Influence of post-treatment strategies on the properties of activated chars from broiler manure.

PubMed

Lima, Isabel M; Boykin, Debbie L; Thomas Klasson, K; Uchimiya, Minori

2014-01-01

There are a myriad of carbonaceous precursors that can be used advantageously to produce activated carbons or chars, due to their low cost, availability and intrinsic properties. Because of the nature of the raw material, production of granular activated chars from broiler manure results in a significant ash fraction. This study was conducted to determine the influence of several pre- and post-treatment strategies in various physicochemical and adsorptive properties of the resulting activated chars. Pelletized samples of broiler litter and cake were pyrolyzed at 700 °C for 1h followed by a 45 min steam activation at 800 °C at different water flow rates from 1 to 5 mL min(-1). For each activation strategy, samples were either water-rinsed or acid-washed and rinsed or used as is (no acid wash/rinse). Activated char's physicochemical and adsorptive properties towards copper ions were selectively affected by both pre- and post-treatments. Percent ash reduction after either rinsing or acid washing ranged from 1.1 to 15.1% but washed activated chars were still alkaline with pH ranging from 8.4 to 9.1. Acid washing or water rinsing had no significant effect in the ability of the activated char to adsorb copper ions, however it significantly affected surface area, pH, ash content and carbon content. Instead, manure type (litter versus cake) and the activation water flow rate were determining factors in copper ion adsorption which ranged from 38 mg g(-1) to 104 mg g(-1) of activated char. Moreover, strong positive correlations were found between copper uptake and concentration of certain elements in the activated char such as phosphorous, sulfur, calcium and sodium. Rinsing could suffice as a post treatment strategy for ash reduction since no significant differences in the carbon properties were observed between rinsed and acid wash treatments. Published by Elsevier Ltd.

The effect of char structure on burnout during pulverized coal combustion at pressure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, G.; Wu, H.; Benfell, K.E.

An Australian bituminous coal sample was burnt in a drop tube furnace (DTF) at 1 atm and a pressurized drop tube furnace (PDTF) at 15 atm. The char samples were collected at different burnout levels, and a scanning electron microscope was used to examine the structures of chars. A model was developed to predict the burnout of char particles with different structures. The model accounts for combustion of the thin-walled structure of cenospheric char and its fragmentation during burnout. The effect of pressure on reaction rate was also considered in the model. As a result, approximately 40% and 70% cenosphericmore » char particles were observed in the char samples collected after coal pyrolysis in the DTF and PDTF respectively. A large number of fine particles (< 30 mm) were observed in the 1 atm char samples at burnout levels between 30% and 50%, which suggests that significant fragmentation occurred during early combustion. Ash particle size distributions show that a large number of small ash particles formed during burnout at high pressure. The time needed for 70% char burnout at 15 atm is approximately 1.6 times that at 1 atm under the same temperature and gas environment conditions, which is attributed to the different pressures as well as char structures. The overall reaction rate for cenospheric char was predicted to be approximately 2 times that of the dense chars, which is consistent with previous experimental results. The predicted char burnout including char structures agrees reasonably well with the experimental measurements that were obtained at 1 atm and 15 atm pressures.« less

Which kind of aromatic structures are produced during biomass charring? New insights provided by modern solid-state NMR spectroscopy

NASA Astrophysics Data System (ADS)

Knicker, Heike; Paneque-Carmona, Marina; Velasco-Molina, Marta; de la Rosa, José Maria; León-Ovelar, Laura Regina; Fernandez-Boy, Elena

2017-04-01

Intense research on biochar and charcoal of the last years has revealed that depending on the production conditions, the chemical and physical characteristics of their aromatic network can greatly vary. Since such variations are determining the behavior and stability of charred material in soils, a better understanding of the structural changes occurring during their heating and the impact of those changes on their function is needed. One method to characterize pyrogenic organic matter (PyOM) represents solid-state 13C NMR spectroscopy applying the cross polarization (CP) magic angle spinning technique (MAS). A drawback of this technique is that the quantification of NMR spectra of samples with highly condensed and proton-depleted structures is assumed to be bias. Typical samples with such attributes are charcoals produced at temperatures above 700°C under pyrolytic conditions. Commonly their high condensation degree leads to graphenic structures that are not only reducing the CP efficiency but create also a conductive lattice which acts as a shield and prevents the entering of the excitation pulse into the sample during the NMR experiments. Since the latter can damage the NMR probe and in the most cases the obtained NMR spectra show only one broad signal assignable to aromatic C, this technique is rarely applied for characterizing high temperature chars or soot. As a consequence, a more detailed knowledge of the nature of the aromatic ring systems is still missing. The latter is also true for the aromatic domains of PyOM produced at lower temperatures, since older NMR instruments operating at low magnetic fields deliver solid-state 13C NMR spectra with low resolution which turns a more detailed analysis of the aromatic chemical shift region into a challenging task. In order to overcome this disadvantages, modern NMR spectroscopy offers not only instruments with greatly improved resolution but also special pulse sequences for NMR experiments which allow a more detailed chemical shift assignment. Applying the latter to various charcoals and biochars, we intended to test their usefulness for a better characterization of PyOM and elucidation how specific aromatic features can affect their behavior in soils. We could demonstrate that furans represent the major compound class of low temperature chars produced from woody material. As indicated by 2D techniques, residual alkyl C in such chars has minor covalent binding to the aromatic network. Reducing the electrical conductivity of high-temperature chars by addition of aluminum oxide permitted the application of the cross CP technique. Determination of the relaxation and CP dynamics confirmed high rigidity of their aromatic domains which were dominated by coronene-type moieties. In contrast to common view, we could demonstrate that quantifiable CP NMR spectra can be obtained from high temperature chars with contact times of 3 to 5 ms and pulse delays > 3 s.

Preparation and characterization of activated carbon from the char produced in the thermolysis of granulated scrap tyres.

PubMed

López, F A; Centeno, T A; Rodríguez, O; Alguacil, E J

2013-05-01

The char produced in the thermolysis of granulated scrap tyres has few market outlets, reducing the economic viability of the thermolytic process. This paper reports the potential of this char as a low-cost precursor of porous carbons. The tyre-derived char was demineralized in either alkaline or acidic media to reduce its ash, zinc, sulfur, and silica contents. The lowest impurity content was achieved with an HNO3/H2O treatment. The resulting demineralized char was then subjected to activation by KOH or CO2. The Brunauer-Emmett-Teller (BET)-specific surface area of the activated carbon produced by the KOH treatment was 242 m2/g, whereas that of the CO2-activated carbon was 720 m2/g. The textural properties of the latter product were similar to those of some commercial activated carbons. The use of tyre-derived char as a precursor of porous carbons could render the thermolytic treatment of scrap tyres more economically attractive. Char produced in thermolysis of granulated scrap tyres has a few market outlets; in this paper an alternative for its use is presented. The char was converted into activated carbon with textural properties similar to those of some commercial activated carbons. This process could render the thermolytic treatment of scrap tyres more economically attractive.

How do molecular marker patterns of BC change at increasing age of chars?

NASA Astrophysics Data System (ADS)

Schneider, M. P. W.; Hilf, M.; Schmidt, M. W. I.

2009-04-01

Black carbon (BC) is considered to be a relatively stable form of organic carbon. However, previous results have shown that the physical and chemical properties of BC can vary considerably with formation temperature. Thus, to understand the long-term carbon sink potential of BC there is increasing interest to gain more information about i) the conditions under which BC was formed, and ii) the resulting degradability of BC under natural conditions. In a first step, we synthesised chars from two different sources of biomass (chestnut wood, rice straw) under well-defined conditions as model substances to analyse the changes in their molecular structure at increasing formation temperature. Results are presented obtained from a set of laboratory produced char samples pyrolysed at increasing temperatures with a high resolution between 200 and 1000 °C. The chars were characterized by a molecular marker method for pyrogenic carbon quantification, which additionally provides information about the degree of condensation of chars. At temperatures between 275 and 500°C, which typically are observed during wildfires and thus are relevant for natural char formation, the molecular marker pattern of the chars remains almost constant. In a next step, we analysed changes in the molecular marker patterns of chars from a chronosequence, with BC deposited between 0 and 100 years ago. Based on the data obtained from the laboratory char series, we compare changes in the molecular marker patterns of the chars from the chronosequence over time. These results show if less condensed forms of BC are degraded preferentially and more condensed, aromatic backbone of BC becomes enriched in the soils with time of degradation. Our results provide information about the fate of BC in the environment, which has important implications in the context of carbon sequestration strategies.

Combustion and Gasification Properties of Plastics Particles.

PubMed

Zevenhoven, Ron; Karlsson, Magnus; Hupa, Mikko; Frankenhaeuser, Martin

1997-08-01

The combustion and gasification behavior of the most common plastics is studied and compared with conventional fuels such as coal, peat, and wood. The aim is to give background data for finding the optimum conditions for co-combustion or co-gasification of a conventional fuel with a certain amount of plastic-derived fuel. Atmospheric or pressurized fluidized bed co-combustion of conventional fuels and plastics are considered to be promising future options. The plastics investigated were poly(ethylene) (PE), poly(propylene) (PP), poly(styrene) (PS), and poly(vinyl chloride) (PVC). Some of the samples had a print or color. The reference fuels were Polish bituminous coal, Finnish peat, and Finnish pine wood. PE, PP, and PS were found to burn like oil. The particles shrank to a droplet and burned completely during the pyrolysis stage, leaving no char. Printing and coloring left a small portion of ash. PVC was the only plastic that produced a carbonaceous residue, and its timescales for heating, devolatilization, and char burning were of the same order as those for peat and wood, and much shorter for the other plastics studied. An important result is that char from PVC contains less than 1% chlorine,99% hydrocarbon. The gasification rate of PVC char (at 1 bar and 25 bar) was of the same order as that of char from coal. Peat-char and wood-char were gasified an order of magnitude faster.

The Erratic Behavior of Lesions in Burnt Bone.

PubMed

Collini, Federica; Amadasi, Alberto; Mazzucchi, Alessandra; Porta, Davide; Regazzola, Valeria Luisa; Garofalo, Paola; Di Blasio, Annalisa; Cattaneo, Cristina

2015-09-01

This study analyses depressed fractures (by blunt force trauma) and circular full-thickness injuries (drill injuries and gunshot wounds) in charred bones. Fifty bovine ribs (total 104 lesions) were divided into three groups. The first group consisted in 20 depressed hammer-produced fractures; in the second one, 60 round drill-holes were produced (30 circular, 30 semicircular); in the third group, 12 fleshed and 12 skeletonized ribs were hit by 9-mm bullets. Each specimen was carbonized in an electric oven up to 800°C. Morphological and metric analyses were performed before and after: morphological features were preserved, but depressed fractures showed an increase in their dimensions (p-value<0.05); the drilled holes shrunk (p-value<0.01); the charring cycle increased the number of fractures in samples with gunshot wounds differently in fleshed and defleshed ribs. This study showed the complex behavior of charred bone, for what concerns the interpretation of trauma and how caution should be applied. © 2015 American Academy of Forensic Sciences.

Molecular Analysis of Primary Vapor and Char Products during Stepwise Pyrolysis of Poplar Biomass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, Roger W.; Reinot, Tonu; McClelland, John F.

2010-08-03

Pyrolysis of biomass produces both pyrolysis oil and solid char. In this study, poplar has been pyrolyzed in a stepwise fashion over a series of temperatures from 200 to 500°C, and both the primary products contributing to pyrolysis oil and the changes in the pyrolyzing poplar surface leading toward char have been characterized at each step. The primary products were identified by direct analysis in real time (DART) mass spectrometry, and the changes in the poplar surface were monitored using Fourier transform infrared (FTIR) photoacoustic spectroscopy, with a sampling depth of a few micrometers. The primary products from pyrolyzing cellulose,more » xylan, and lignin under similar conditions were also characterized to identify the sources of the poplar products.« less

Molecular Analysis of Primary Vapor and Char Products during Stepwise Pyrolysis of Poplar Biomass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, Roger W.; Reinot, Tonu; McClelland, John F.

2010-08-30

Pyrolysis of biomass produces both pyrolysis oil and solid char. In this study, poplar has been pyrolyzed in a stepwise fashion over a series of temperatures from 200 to 500 C, and both the primary products contributing to pyrolysis oil and the changes in the pyrolyzing poplar surface leading toward char have been characterized at each step. The primary products were identified by direct analysis in real time (DART) mass spectrometry, and the changes in the poplar surface were monitored using Fourier transform infrared (FTIR) photoacoustic spectroscopy, with a sampling depth of a few micrometers. The primary products from pyrolyzingmore » cellulose, xylan, and lignin under similar conditions were also characterized to identify the sources of the poplar products.« less

Co-gasification of tire and biomass for enhancement of tire-char reactivity in CO2 gasification process.

PubMed

Lahijani, Pooya; Zainal, Zainal Alimuddin; Mohamed, Abdul Rahman; Mohammadi, Maedeh

2013-06-01

In this investigation, palm empty fruit bunch (EFB) and almond shell (AS) were implemented as two natural catalysts rich in alkali metals, especially potassium, to enhance the reactivity of tire-char through co-gasification process. Co-gasification experiments were conducted at several blending ratios using isothermal Thermogravimetric analysis (TGA) under CO2. The pronounced effect of inherent alkali content of biomass-chars on promoting the reactivity of tire-char was proven when acid-treated biomass-chars did not exert any catalytic effect on improving the reactivity of tire-char in co-gasification experiments. In kinetic studies of the co-gasified samples in chemically-controlled regime, modified random pore model (M-RPM) was adopted to describe the reactive behavior of the tire-char/biomass-char blends. By virtue of the catalytic effect of biomass, the activation energy for tire-char gasification was lowered from 250 kJ/mol in pure form 203 to 187 kJ/mol for AS-char and EFB-char co-gasified samples, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Light Weight Ceramic Ablators for Mars Follow-on Mission Vehicle Thermal Protection System

NASA Technical Reports Server (NTRS)

Tran, Huy K.; Rasky, Daniel J.; Hsu, Ming-Ta; Turan, Ryan

1994-01-01

New Light Weight Ceramic Ablators (LCA) were produced by using ceramic and carbon fibrous substrates, impregnated with silicone and phenolic resins. The special infiltration techniques (patent pending) were developed to control the amount of organic resins in the highly porous fiber matrices so that the final densities of LCA's range from 0.22 to 0.24 g/cc. This paper presents the thermal and ablative performance of the Silicone Impregnated Reusable Ceramic Ablators (SIRCA) in simulated entry conditions for Mars-Pathfinder in the Ames 60 MW Interaction Heating Facility (I HF). Arc jet test results yielded no evidence of char erosion and mass loss at high stagnation pressures to 0.25 atm. Minimal silica melt was detected on surface char at a stagnation pressure of 0.31 atm. Four ceramic substrates were used in the production of SIRCA's to obtain the effective of boron oxide present in substrate so the thermal performance of SIRCA's. A sample of SIRCA was also exposed to the same heating condition for five cycles and no significant mass loss or recession was observed. Tensile testing established that the SIRCA tensile strength is about a factor of two higher than that of the virgin substrates. Thermogravimetric Analysis (TGA) of the char in nitrogen and air showed no evidence of free carbon in the char. Scanning Electron Microscopy of the post test sample showed that the char surface consists of a fibrous structure that was sealed with a thin layer of silicon oxide melt.

Strategy for Passivating Char Efficiently at the Pilot Scale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunning, Timothy C

Fast pyrolysis is a promising pathway for the commercialization of liquid transportation fuels from biomass. Fast pyrolysis is performed at moderate heat (450-600 degrees Celcius) in an oxygen-deficient environment. One of the products of fast pyrolysis is biochar, which is often used as a heat source or as a soil amendment. Biochar is a partially reacted solid that is created in the production of bio-oil during fast pyrolysis. Biochar produced at these conditions contains significant quantities of carbon that adsorb oxygen when exposed to air. Biochar adsorption of oxygen is an exothermic process that may generate sufficient heat for combustionmore » in ambient air. Biochar is also a self-insulating material which compounds the effects of heat generated internally. These factors lead to safety concerns and material handling difficulties. The Thermochemical Process Development Unit at the National Renewable Energy Laboratory operates a pilot plant that may be configured for fast pyrolysis, gasification, and will be introducing catalytic fast pyrolysis capabilities in 2018. The TCPDU designed and installed a system to introduce oxygen to collected biochar systematically for a controlled passivation. Biochar is collected and cooled in an oxygen deficient environment during fast pyrolysis. Oxygen is then introduced to the biochar on a mass flow basis. A sparger imbedded within the biochar sample near the bottom of the bed flows air diluted with nitrogen into the char bed, and excess gasses are removed from the top of the collection drum, above the char bed. Pressure within the collection drum is measured indicating adequate flow through filters. Sample weight is recorded before and after passivation. During passivation, temperature is measured at 18 points within the char bed. Oxygen content and temperature are measured leaving the char bed. Maximum temperature parameters were established to ensure operator safety during biochar passivation. Extensive passivation data was collected on pine and blended feedstocks and has been analyzed to characterize the exotherm of char samples. Observations and data collected while passivating char will be discussed.« less

Development of Acid Functional Groups and Lactones During the Thermal Degradation of Wood and Wood Components

USGS Publications Warehouse

Rutherford, David W.; Wershaw, Robert L.; Reeves, James B.

2008-01-01

Black carbon (pyrogenic materials including chars) in soils has been recognized as a substantial portion of soil organic matter, and has been shown to play a vital role in nutrient cycling; however, little is known concerning the properties of this material. Previous studies have largely been concerned with the creation of high-surface-area materials for use as sorbents. These materials have been manufactured at high temperature and have often been activated. Chars occurring in the environment can be formed over a wide range of temperature. Because it is extremely difficult to isolate black carbon once it has been incorporated in soils, chars produced in the laboratory under controlled conditions can be used to investigate the range of properties possible for natural chars. This report shows that charring conditions (temperature and time) have substantial impact on the acid functional group and lactone content of chars. Low temperatures (250?C) and long charring times (greater than 72 hours) produce chars with the highest acid functional group and lactone content. The charring of cellulose appears to be responsible for the creation of the acid functional group and lactones. The significance of this study is that low-temperature chars can have acid functional group contents comparable to humic materials (as high as 8.8 milliequivalents per gram). Acid functional group and lactone content decreases as charring temperature increases. The variation in formation conditions expected under natural fire conditions will result in a wide range of sorption properties for natural chars which are an important component of soil organic matter. By controlling the temperature and duration of charring, it is possible to tailor the sorption properties of chars, which may be used as soil amendments.

Characterization and Activation Study of Black Chars Derived from Cellulosic Biomass Pyrolyzed at Very High Temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Contescu, Cristian I.; Gallego, Nidia C.

2017-03-01

The State of Tennessee, in partnership with the University of Tennessee (UT) and the Oak Ridge National Laboratory (ORNL), has created the RevV! Manufacturing voucher program to help Tennessee manufacturers gain access to the world-class resources at ORNL. As a part of this program, ORNL was working with Proton Power, Inc. (PPI), a rapidly growing company located in Lenoir City, Tennessee. PPI has developed a patented renewable energy system that uses biomass and waste sources to produce inexpensive hydrogen gas or synthetic fuels which are economically competitive with fossil fuels. The pyrolysis process used by PPI in their manufacturing chainmore » generates significant amounts of black carbon char as by-product. The scope of ORNL collaboration with PPI was assessing the black carbon char as a potential feedstock for activated carbon production, as this could be a potentially new revenue stream. During 2015-2016 ORNL received eight char samples from PPI and characterized their initial properties, simulated their physical activation by carbon dioxide, prepared gram-size samples of physically activated carbons, and characterized their surface and porosity properties. This report presents a summary of the work methods employed and the results obtained in the collaborative project between ORNL and PPI.« less

Production of activated char from Illinois coal for flue gas cleanup

USGS Publications Warehouse

Lizzio, A.A.; DeBarr, J.A.; Kruse, C.W.

1997-01-01

Activated chars were produced from Illinois coal and tested in several flue gas cleanup applications. High-activity chars that showed excellent potential for both SO2 and NOx removal were prepared from an Illinois No. 2 bituminous coal. The SO2 (120 ??C) and NOx (25 ??C) removal performance of one char compared favorably with that of a commercial activated carbon (Calgon Centaur). The NOx removal performance of the same char at 120 ??C exceeded that of the Centaur carbon by more than 1 order of magnitude. Novel char preparation methods were developed including oxidation/thermal desorption and hydrogen treatments, which increased and preserved, respectively, the active sites for SO2 and NOx adsorption. The results of combined SO2/NOx removal tests, however, suggest that SO2 and NOx compete for similar adsorption sites and SO2 seems to be more strongly adsorbed than NO. A low-activity, low-cost char was also developed for cleanup of incinerator flue gas. A three-step method involving coal preoxidation, pyrolysis, and CO2 activation was used to produce the char from Illinois coal. Five hundred pounds of the char was tested on a slipstream of flue gas from a commercial incinerator in Germany. The char was effective in removing >97% of the dioxins and furans present in the flue gas; mercury levels were below detectable limits.

At the forefront: evidence of the applicability of using environmental DNA to quantify the abundance of fish populations in natural lentic waters with additional sampling considerations

USGS Publications Warehouse

Klobucar, Stephen L.; Rodgers, Torrey W.; Budy, Phaedra

2017-01-01

Environmental DNA (eDNA) sampling has proven to be a valuable tool for detecting species in aquatic ecosystems. Within this rapidly evolving field, a promising application is the ability to obtain quantitative estimates of relative species abundance based on eDNA concentration rather than traditionally labor-intensive methods. We investigated the relationship between eDNA concentration and Arctic char (Salvelinus alpinus) abundance in five well-studied natural lakes; additionally, we examined the effects of different temporal (e.g., season) and spatial (e.g., depth) scales on eDNA concentration. Concentrations of eDNA were linearly correlated with char population estimates ( = 0.78) and exponentially correlated with char densities ( = 0.96 by area; 0.82 by volume). Across lakes, eDNA concentrations were greater and more homogeneous in the water column during mixis; however, when stratified, eDNA concentrations were greater in the hypolimnion. Overall, our findings demonstrate that eDNA techniques can produce effective estimates of relative fish abundance in natural lakes. These findings can guide future studies to improve and expand eDNA methods while informing research and management using rapid and minimally invasive sampling.

High temperature gasification of high heating-rate chars using a flat-flame reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Tian; Niu, Yanqing; Wang, Liang

The increasing interest in gasification and oxy-fuel combustion of biomass has heightened the need for a detailed understanding of char gasification in industrially relevant environments (i.e., high temperature and high-heating rate). Despite innumerable studies previously conducted on gasification of biomass, very few have focused on such conditions. Consequently, in this study the high-temperature gasification behaviors of biomass-derived chars were investigated using non-intrusive techniques. Two biomass chars produced at a heating rate of approximately 10 4 K/s were subjected to two gasification environments and one oxidation environment in an entrained flow reactor equipped with an optical particle-sizing pyrometer. A coal charmore » produced from a common U.S. low sulfur subbituminous coal was also studied for comparison. Both char and surrounding gas temperatures were precisely measured along the centerline of the furnace. Despite differences in the physical and chemical properties of the biomass chars, they exhibited rather similar reaction temperatures under all investigated conditions. On the other hand, a slightly lower particle temperature was observed in the case of coal char gasification, suggesting a higher gasification reactivity for the coal char. A comprehensive numerical model was applied to aid the understanding of the conversion of the investigated chars under gasification atmospheres. In addition, a sensitivity analysis was performed on the influence of four parameters (gas temperature, char diameter, char density, and steam concentration) on the carbon conversion rate. Here, the results demonstrate that the gas temperature is the most important single variable influencing the gasification rate.« less

High temperature gasification of high heating-rate chars using a flat-flame reactor

DOE PAGES

Li, Tian; Niu, Yanqing; Wang, Liang; ...

2017-08-25

The increasing interest in gasification and oxy-fuel combustion of biomass has heightened the need for a detailed understanding of char gasification in industrially relevant environments (i.e., high temperature and high-heating rate). Despite innumerable studies previously conducted on gasification of biomass, very few have focused on such conditions. Consequently, in this study the high-temperature gasification behaviors of biomass-derived chars were investigated using non-intrusive techniques. Two biomass chars produced at a heating rate of approximately 10 4 K/s were subjected to two gasification environments and one oxidation environment in an entrained flow reactor equipped with an optical particle-sizing pyrometer. A coal charmore » produced from a common U.S. low sulfur subbituminous coal was also studied for comparison. Both char and surrounding gas temperatures were precisely measured along the centerline of the furnace. Despite differences in the physical and chemical properties of the biomass chars, they exhibited rather similar reaction temperatures under all investigated conditions. On the other hand, a slightly lower particle temperature was observed in the case of coal char gasification, suggesting a higher gasification reactivity for the coal char. A comprehensive numerical model was applied to aid the understanding of the conversion of the investigated chars under gasification atmospheres. In addition, a sensitivity analysis was performed on the influence of four parameters (gas temperature, char diameter, char density, and steam concentration) on the carbon conversion rate. Here, the results demonstrate that the gas temperature is the most important single variable influencing the gasification rate.« less

Interaction and its induced inhibiting or synergistic effects during co-gasification of coal char and biomass char.

PubMed

Ding, Liang; Zhang, Yongqi; Wang, Zhiqing; Huang, Jiejie; Fang, Yitian

2014-12-01

Co-gasification of coal char and biomass char was conducted to investigate the interactions between them. And random pore model (RPM) and modified random pore model (MRPM) were applied to describe the gasification behaviors of the samples. The results show that inhibiting effect was observed during co-gasification of corn stalk char with Hulunbeier lignite coal char, while synergistic effects were observed during co-gasification of corn stalk char with Shenmu bituminous coal char and Jincheng anthracite coal char. The inhibiting effect was attributed to the intimate contact and comparable gasification rate between biomass char and coal char, and the loss of the active form of potassium caused by the formation of KAlSiO4, which was proved to be inactive during gasification. While the synergistic effect was caused by the high potassium content of biomass char and the significant difference of reaction rate between coal char and biomass char during gasification. Copyright © 2014 Elsevier Ltd. All rights reserved.

What happens with the nitrogen in sewage sludge once this material is pyrolyzed?

NASA Astrophysics Data System (ADS)

Paneque, Marina; María De la Rosa, José; Kern, Jürgen; Knicker, Heike

2017-04-01

The transformation of sewage sludge (SS) into char by pyrolysis achieves sludge hygienization, a necessary step prior to a possible application on agricultural soils. Former studies indicated that during this process part of the organic nitrogen (No) of this material is incorporated into the aromatic network of the charred product and forms the so called black N (BN). De la Rosa and Knicker (2011) showed further that at least some of the BN is bioavailable. However, neither the pathways of BN formation nor its chemical structure is well understood. Therefore, we studied the production of inorganic N (Ni) and the forms of No after subjecting two types of SS to hydrothermal carbonization (HTC) and dry pyrolysis (Dry-Py). The samples were collected at two different stages of the wastewater treatment (hereafter A_SS and T_SS) at the Experimental Wastewater Treatment plant CENTA, located in Carrion de los Céspedes (Southern Spain). Four chars were produced by HTC at 200°C and 260°C, and with residence times of 30 min and 3 hours. Dry pyrolysis char was obtained after heating at 600°C for 1 hour. The organic N forms were revealed by solid-state 15N nuclear magnetic resonance (NMR) spectroscopy. All pyrolysis conditions resulted in a decrease of the amount of total N (Nt). Whereas HTC preserved between 83-59% of original N, only 2% were recovered in the char after Dry-Py. With respect to Ni, the amounts of ammonium and nitrite increased between 2 and 4 times compared to the non-treated SS after HTC. After Dry-Py no Ni was detected in the solid residue. The solid-state 15N NMR spectra of the non-treated SS are dominated by the signals assignable to amide-N. With increasing temperature and residence time applied during HTC, a shift of the signal intensity toward the region of pyrrole-N was evidenced. The largest contribution of pyrrole-N was identified in the sample obtained after heating at 260°C for 3h although the 15N-intensity in the chemical shift region of amide/carbazole N dominated the spectrum. In contrast, Dry-Py resulted in a dominance of pyrrole-N. In conclusion, our study demonstrated the impact of the pyrolysis conditions on the quantity and quality of N-forms in chars of SS. Considering the N fertilization potential, HTC chars may be more suitable than chars produced by Dry-Py if fast fertilization is needed due to the presence of Ni. On the other hand, the binding of N in heterocyclic structures retards its bioavailability. Thus Dry-Py chars will be a better choise, if slow N-release is wanted. However, deeper and specific researchers are necessary to confirm this hypothesis. De la Rosa JM, Knicker H (2011) Bioavailability of N released from N-rich pyrogenic organic matter: An incubation study. Soil Biology and Biogeochemistry 43: 2368-2373

Feasibility of mercury removal from simulated flue gas by activated chars made from poultry manures.

PubMed

Klasson, K Thomas; Lima, Isabel M; Boihem, Larry L; Wartelle, Lynda H

2010-12-01

Increased emphasis on reduction of mercury emissions from coal fired electric power plants has resulted in environmental regulations that may in the future require application of activated carbons as mercury sorbents for mercury removal. At the same time, the quantity of poultry manure generated each year is large and technologies that take advantage of the material should be explored. The purpose of the work was to obtain preliminary data to investigate if activated chars made from different poultry manures could adsorb mercury from simulated flue gas. In laboratory experiments, activated chars made from chicken cake and litter removed mercury from the gas as well as a commercial alternative. It was also found that acid-washing these chars after activation may improve pore structure but does not influence the mercury removal efficiency. Activated chars were also made from turkey cake and litter. These raw materials produced activated chars with similar pore structure as those made from chicken manure, but they did not adsorb mercury as well. Acid-washing the turkey manure-based chars improved their performance, but this step would add to the cost of production. Preliminary evaluations suggest that unwashed activated chars may cost as little as $0.95/kg to produce. Published by Elsevier Ltd.

Compositional and thermal evaluation of lignocellulosic and poultry litter chars via high and low temperature pyrolysis

USDA-ARS?s Scientific Manuscript database

Inorganic elements in biomass feedstocks can influence thermochemical reactions as well as the resultant chars elemental, compositional, and thermal characteristics. Chars were produced using slow pyrolysis at less than 400 and at higher than 500 degree Celsius from sugarcane bagasse, peanut hulls,...

Subcellular distribution of trace elements and liver histology of landlocked Arctic char (Salvelinus alpinus) sampled along a mercury contamination gradient.

PubMed

Barst, Benjamin D; Rosabal, Maikel; Campbell, Peter G C; Muir, Derek G C; Wang, Xioawa; Köck, Günter; Drevnick, Paul E

2016-05-01

We sampled landlocked Arctic char (Salvelinus alpinus) from four lakes (Small, 9-Mile, North, Amituk) in the Canadian High Arctic that span a gradient of mercury contamination. Metals (Hg, Se, Tl, and Fe) were measured in char tissues to determine their relationships with health indices (relative condition factor and hepatosomatic index), stable nitrogen isotope ratios, and liver histology. A subcellular partitioning procedure was employed to determine how metals were distributed between potentially sensitive and detoxified compartments of Arctic char livers from a low- and high-mercury lake (Small Lake and Amituk Lake, respectively). Differences in health indices and metal concentrations among char populations were likely related to differences in feeding ecology. Concentrations of Hg, Se, and Tl were highest in the livers of Amituk char, whereas concentrations of Fe were highest in Small and 9-Mile char. At the subcellular level we found that although Amituk char had higher concentrations of Tl in whole liver than Small Lake char, they maintained a greater proportion of this metal in detoxified fractions, suggesting an attempt at detoxification. Mercury was found mainly in potentially sensitive fractions of both Small and Amituk Lake char, indicating that Arctic char are not effectively detoxifying this metal. Histological changes in char livers, mainly in the form of melano-macrophage aggregates and hepatic fibrosis, could be linked to the concentrations and subcellular distributions of essential or non-essential metals. Copyright © 2016 Elsevier Ltd. All rights reserved.

The effect of chars and their water extractable organic carbon (WEOC) fractions on atrazine adsorption-desorption processes

NASA Astrophysics Data System (ADS)

Cavoski, I.; Jablonowski, N.; Burauel, P.; Miano, T.

2012-04-01

Chars are carbonaceous material produced from different type of biomass by pyrolysis. They are known as highly effective adsorbents for atrazine therefore limiting its degradation and its diffusion into the aqueous phase. The aim of the present work is to study the effects of different chars and char's derived WEOC on atrazine sorption-desorption processes. The five chars been used in this study derived from: 1) fast pyrolysis from hard wood (FP1); 2) flash pyrolysis from soft wood (FP2); 3) slow pyrolysis from deciduous wood (CC); 4) gasification from deciduous wood (GC) and 5) the market, purchased as activated charcoal standard (AC). Short-term batch equilibration tests were conducted to assess the sorption-desorption behavior of 14C-labeled atrazine on the chars, with a special focus on the desorption behavior using successive dilution method with six consecutive desorption step. Chars and their WEOC were physically and chemically characterized. Results demonstrate that biomass and pyrolysis process used to produce chars affect their physical and chemical properties, and atrazine adsorption-desorption behavior. Atrazine desorption resulted from the positive and competitive interactions between WEOC and chars surfaces. WEOC pool play important role in atrazine adsorption-desorption behavior. FP1 and FP2 with higher concentration of WEOC showed higher desorption rates, whereas GC, CC and AC with insignificant WEOC concentration strongly adsorb atrazine with low desorption rates. According to our results, when high WEOC pools chars are concerned, an increase in atrazine desorption can be observed but further studies would help in confirming the present results.

Experimental Study of Hydrogasification of Lignite and Subbituminous Coal Chars

PubMed Central

Gil, Stanisław

2015-01-01

The experimental facility for pressure hydrogasification research was adapted to the pressure of 10 MPa and temperature of 1300 K, which ensured repeatability of results and hydrogen heating to the process temperature. A hydrogasification reaction of chars produced from two rank coals was investigated at temperatures up to 1173 K, pressures up to 8 MPa, and the gas flow rates of 0.5–5 dmn 3/min. Reactivity of the “Szczerców” lignite char was found to be slightly higher than that of the subbituminous “Janina” coal char produced under the same conditions. A high value of the char reactivity was observed to a certain carbon conversion degree, above which a sharp drop took place. It was shown that, to achieve proper carbon conversion, the hydrogasification reaction must proceed at a temperature above 1200 K. PMID:26065028

ON-SITE PRODUCTION OF ACTIVATED CARBON FROM KRAFT BLACK LIQUOR

EPA Science Inventory

A pilot plant was designed and constructed to produce char via the St. Regis hydropyrolysis kraft chemical recovery process and to produce activated carbon from the char. This report includes discussion of laboratory and prepilot work, the pilot plant, and presents operating resu...

Temperature influence on the fast pyrolysis of manure samples: char, bio-oil and gases production

NASA Astrophysics Data System (ADS)

Fernandez-Lopez, Maria; Anastasakis, Kostas; De Jong, Wiebren; Valverde, Jose Luis; Sanchez-Silva, Luz

2017-11-01

Fast pyrolysis characterization of three dry manure samples was studied using a pyrolyzer. A heating rate of 600°C/s and a holding time of 10 s were selected to reproduce industrial conditions. The effect of the peak pyrolysis temperature (600, 800 and 1000°C) on the pyrolysis product yield and composition was evaluated. Char and bio-oil were gravimetrically quantified. Scanning electron microscopy (SEM) was used to analyse the char structure. H2, CH4, CO and CO2 were measured by means of gas chromatography (GC). A decrease in the char yield and an increase of the gas yield were observed when temperature increased. From 800°C on, it was observed that the char yield of samples Dig R and SW were constant, which indicated that the primary devolatilization reactions stopped. This fact was also corroborated by GC analysis. The bio-oil yield slightly increased with temperature, showing a maximum of 20.7 and 27.8 wt.% for samples Pre and SW, respectively, whereas sample Dig R showed a maximum yield of 16.5 wt.% at 800°C. CO2 and CO were the main released gases whereas H2 and CH4 production increased with temperature. Finally, an increase of char porosity was observed with temperature.

Power and Limitations of Anhydrosugars to Trace Historical Natural and Anthropogenic Inputs of charcoal BC to Aquatic Systems

NASA Astrophysics Data System (ADS)

Louchouarn, P.; Kuo, L.; Brandenberger, J. M.; Andresen, C. S.; Kjaer, K. H.; Dalton, M.

2011-12-01

Plant-derived chars are the solid residues from incomplete combustion of plant materials. They are an important constituent in the black carbon (BC) continuum, an array of diverse pyrogenic organic materials ranging from slightly charred biomass (low temperature) to highly condensed refractory soot (high temperature). The characterization and quantification of plant-derived chars in environmental samples is a challenging process due to the heterogeneous nature of these substances. Most of the BC methods using oxidative approaches that seek to remove non-BC materials are limited in their potential to identify and quantify plant-derived chars because of their relative labilities compared to the condensed BC forms such as soot. Anhydrosugars, such as levoglucosan and its isomers (mannosan and galactosan), have generated considerable interest in recent years in BC research because they are exclusive thermal degradation products of cellulose/hemicellulose and are produced in different proportions in chars and smokes from low temperature combustion of different plant species permitting some source discrimination in environmental samples (e.g. softwoods vs. hardwoods; gymnosperms vs. angiosperms). We show here a synthesis of several years of work using levoglucosan in diverse environments to reconstruct local to large-scale environmental change from climate-driven wildfires to human and accidental fires. For example, in the Hood Canal (WA), the striking consistency between the fluxes of levoglucosan, the Pacific Decadal Oscillation (PDO) Index, and the Palmer Drought Severity Index (PDSI), suggests that climate oscillations may play a role in the historical wildfire activities and thus influence the inputs of char-BC to the Puget Sound. Similarly, peaks in anhydrosugars in a sediment core from Lake Copenhagen record large-scale accidental fires in the city of Copenhagen during the early and late 18th Century, and help constrain the geochronology of the core beyond the limit of the 210Pb dating potential (late 19th Century). Despite these "successes" in sedimentary systems, the application of anhydrosugars to reconstruct historical char-BC inputs to aquatic systems is fraught with both methodological and conceptual issues. For one, anhydrosugars analysis in sediments suffers from more interferences than similar analyses in atmospheric particles. Secondly, and most significantly, the rapid turnover of anhydrosugars in aquatic systems mean that only a small fraction of the original tracers encapsulated in the inner pores of char particles is preserved in sedimentary systems, thus complicating the potential for a direct transfer function between the presence of anhydrosugars and original fluxes of char-BC to aquatic environments.

Chemical characterization of chars developed from thermochemical treatment of Kentucky bluegrass seed screenings

USDA-ARS?s Scientific Manuscript database

Char produced from the gasification of post-seed harvest Kentucky bluegrass residues could be recycled to a cropping system as a soil amendment if chemical characterization determined that the gasification process had not produced or concentrated deleterious chemical or physical factors that might h...

The hierarchical porous structure bio-char assessments produced by co-pyrolysis of municipal sewage sludge and hazelnut shell and Cu(II) adsorption kinetics.

PubMed

Zhao, Bing; Xu, Xinyang; Zeng, Fanqiang; Li, Haibo; Chen, Xi

2018-05-04

The co-pyrolysis technology was applied to municipal sewage sludge (MSS) and hazelnut shell with alkaline activating agent K 2 CO 3 under N 2 atmosphere. The innovative bio-char produced by co-pyrolysis had significant physical and chemical characteristics. The specific surface area reached 1990.23 m 2 /g, and the iodine absorption number was 1068.22 mg/g after co-pyrolysis at 850 °C. Although hazelnut shell was a kind of solid waste, it also had abundant cellulose resource, which could contribute to porous structure of bio-char during co-pyrolysis with MSS and decrease total heavy metals contents of raw material to increase security of bio-chars. Meanwhile, the residual fractions of heavy metals in bio-char were above 92.95% after co-pyrolysis at 900 °C except Cd to prevent heavy metals digestion, and the bio-char presented significant immobilization behavior from co-pyrolysis technology. Moreover, the yield and the iodine absorption number of bio-chars under different process variables were analyzed, and it was confirmed that appropriate process variables could contribute the yield and the iodine absorption number of bio-char and prevent to etch pore structure excessively to collapse. The changes of surface functional groups and crystallographic structure before and after co-pyrolysis were analyzed by FTIR and XRD, respectively. The hierarchical porous structure of bio-char was presented by SEM and N 2 adsorption-desorption isotherm. The Cu(II) adsorption capacity of the bio-char was 42.28 mg/g after 24 h, and surface functional groups acted as active binding sites for Cu(II) adsorption. Langmuir model and pseudo-second-order model can describe process of Cu(II) adsorption well.

Characterization of bio char derived from tapioca skin

NASA Astrophysics Data System (ADS)

Hasnan, F. I.; Iamail, K. N.; Musa, M.; Jaapar, J.; Alwi, H.; Hamid, K. K. K.

2018-03-01

Pyrolysis of tapioca skin was conducted to produce bio chars in the range between 500°C–800°C. Surface modification treatment were performed on bio chars by using chemicals within 24 hours at 30°C and hot water within 1 hour to enhance the bio char’s adsorption properties according to surface area, pore volume, pore size, crystallinity structure and functional groups. The samples were characterized by using BET, XRD, FTIR and Methylene Blue adsorption. Based on BET result, it showed the surface area increased as the pyrolysis temperature increased followed by pore volume and pore size for S0. The optimum temperature for SNaOH, SHW and SMeOH was at 600°C, 700°C and 800°C with the surface area of 75.9874, 274.5066 and 351.5531 m2/g respectively compared to S0 while SP3HO4 has the worst result since it felt on macroporous structure. The percentage of MB adsorption was followed the size of bio chars surface area. Based on FTIR result, at temperature 500°C to 700°C, the bio chars still have functional groups while at 800°C, many functional groups were diminished due to high temperature struck on them. XRD result showed all the bio chars were amorphous. In conclusion, the best surface modification treatment was by Methanol followed by hot water and Sodium Hydroxide at temperature of 700°C and 800°C while Ortho-Phosphoric acid was the worst one and was not suitable for bio char’s surface modification for adsorption purpose.

Spatial and temporal trends of mercury and other metals in landlocked char from lakes in the Canadian Arctic archipelago.

PubMed

Muir, Derek; Wang, Xiaowa; Bright, Doug; Lockhart, Lyle; Köck, Günter

2005-12-01

Spatial and temporal trends of mercury (Hg) and 22 other elements were examined in landlocked Arctic char (Salvelinus alpinus) from six lakes in the Canadian Arctic (Char, Resolute and North Lakes, and Amituk Lake on Cornwallis Island, Sapphire Lake on Devon Island and Boomerang Lake on Somerset Island). The objectives of the study were to compare recent concentrations of Hg and other metals in char with older data from Amituk, Resolute and Char Lakes, in order to examine temporal trends as well as to investigate factors influencing spatial trends in contaminant levels such as lake characteristics, trophic position, size and age of the fish. Geometric mean Hg concentrations in dorsal muscle ranged from 0.147 microg/g wet weight (ww) in Resolute Lake to 1.52 microg/g ww in Amituk Lake for samples collected over the period 1999-2003. Char from Amituk Lake also had significantly higher selenium (Se). Mercury in char from Resolute Lake was strongly correlated with fish length, weight, and age, as well as with thallium, lead and Se. In 5 of 6 lakes, Hg concentrations were correlated with stable nitrogen isotope ratios (delta15N) and larger char were feeding at a higher trophic level presumably due to feeding on smaller char. Weight adjusted mean Hg concentrations in char from Amituk Lake, and unadjusted geometric means in Char Lake and Resolute Lakes, did not show any statistically significant increase from the early 1990s to 2003. However, small sample sizes from 1999-2003 for fish <1000 g limited the power of this comparison in Char and Amituk Lakes. In Resolute Lake char, manganese, strontium and zinc showed consistent decreases from 1997 or 1999 to 2003 while nickel generally increased over the 6 year period. Differences in char trophic level inferred from delta15N values best explained the higher concentrations of Hg in Amituk Lake compared to the other lakes.

Study on coal char ignition by radiant heat flux.

NASA Astrophysics Data System (ADS)

Korotkikh, A. G.; Slyusarskiy, K. V.

2017-11-01

The study on coal char ignition by CO2-continuous laser was carried out. The coal char samples of T-grade bituminous coal and 2B-grade lignite were studied via CO2-laser ignition setup. Ignition delay times were determined at ambient condition in heat flux density range 90-200 W/cm2. The average ignition delay time value for lignite samples were 2 times lower while this difference is larger in high heat flux region and lower in low heat flux region. The kinetic constants for overall oxidation reaction were determined using analytic solution of simplified one-dimensional heat transfer equation with radiant heat transfer boundary condition. The activation energy for lignite char was found to be less than it is for bituminous coal char by approximately 20 %.

Mechanical properties of acacia and eucalyptus wood chars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, M.; Verma, B.B.; Gupta, R.C.

1999-10-01

In the present investigation the effects of carbonization conditions (temperature and heating rate) on the mechanical properties (such as crushing and impact strengths and shatter index) of acacia and eucalyptus wood chars have been determined. The crushing and impact strengths of both the acacia and eucalyptus wood chars (made by slow carbonization) decreased with increase of preparation temperature up to 600 C, followed by an increase thereafter. These wood chars showed a continuous increase in shatter index values with carbonization temperature. In contrast to slow carbonization (heating rate 4 C min{sup {minus}1}), rapid carbonization (heating rate 30 C min{sup {minus}1})more » yielded chars of lower crushing strengths. Slowly carbonized eucalyptus wood gave chars of superior crushing and impact strengths than those produced from acacia wood under the same carbonization conditions. The crushing and impact strengths of these wood chars, in general, have shown an increase with increase in their apparent density. The crushing strength of cubic-shaped wood char decreased with increase in size.« less

Bio-char from treated and untreated oil palm fronds

NASA Astrophysics Data System (ADS)

Sulaiman, Fauziah; Abdullah, Nurhayati; Rahman, Aizuddin Abdul

2013-05-01

The palm oil industry generates almost 94% of biomass in Malaysia, while other agricultural and forestry by-products contribute the remaining of 6%. Oil palm fronds (OPF) are estimated to be the highest available biomass amounting to 44.84 million tonnes in Malaysia. However, studies on OPF for thermochemical conversion technology which has good potential for energy conversion are still lacking. In this work, pyrolysis of OPF is conducted by using a fixed bed reactor. Samples were carbonized at slow pyrolysis temperature of around 300 to 500°C with heating rate of 10°C min-1. In addition, samples were treated for 20 min with distilled water at ambient temperature to reduce the ash content. Effectiveness of pre-treatment can be determined by observing the percentage of ash content reduction of each sample after undergoing washing pre-treatment. At 300°C, the char yields of the untreated OPF were slightly higher at 50.95% compared to the treated sample at 49.77%. Approximately all bio-char from the treated samples have better high heating value (HHV) of around 18-20 MJ kg-1 compared to the untreated samples. Besides that, all treated OPF char is more carbon rich and considered to be environmental friendly due to its low nitrogen content compared to the untreated OPF char. In this work, microscopic analysis of OPF bio-char were also studied by observing and evaluating their structure surface and morphology.

Evaluation of current techniques for isolation of chars as natural adsorbents

USGS Publications Warehouse

Chun, Y.; Sheng, G.; Chiou, C.T.

2004-01-01

Chars in soils or sediments may potentially influence the soil/sediment sorption behavior. Current techniques for the isolation of black carbon including chars rely often on acid demineralization, base extraction, and chemical oxidation to remove salts and minerals, humic acid, and refractory kerogen, respectively. Little is known about the potential effects of these chemical processes on the char surface and adsorptive properties. This study examined the effects of acid demineralization, base extraction, and acidic Cr2O72- oxidation on the surface areas, surface acidity, and benzene adsorption characteristics of laboratory-produced pinewood and wheat-residue chars, pure or mixed with soils, and a commercial activated carbon. Demineralization resulted in a small reduction in the char surface area, whereas base extraction showed no obvious effect. Neither demineralization nor base extraction caused an appreciable variation in benzene adsorption and presumably the char surface properties. By contrast, the Cr2O 72- oxidation caused a >31% reduction in char surface area. The Boehm titration, supplemented by FTIR spectra, indicated that the surface acidity of oxidized chars increased by a factor between 2.3 and 12 compared to nonoxidized chars. Benzene adsorption with the oxidized chars was lower than that with the non-oxidized chars by a factor of >8.9; both the decrease in char surface area and the increase in char surface acidity contributed to the reduction in char adsorptive power. Although the Cr 2O72- oxidation effectively removes resistant kerogen, it is not well suited for the isolation of chars as contaminant adsorbents because of its destructive nature. Alternative nondestructive techniques that preserve the char surface properties and effectively remove kerogen must be sought.

Characterization of a Neochlamydia-like Bacterium Associated with Epitheliocystis in Cultured Artic Char Salvelinus alpinus

USDA-ARS?s Scientific Manuscript database

Infections of branchial epithelium by intracellular gram-negative bacteria, termed epitheliocystis, have limited culture of Arctic char (Salvelinus alpinus). To characterize a bacterium associated with epitheliocystis in cultured char, gills were sampled for histopathologic examination, conventional...

Gasification of the char derived from distillation of granulated scrap tyres.

PubMed

López, Félix A; Centeno, Teresa A; Alguacil, Francisco José; Lobato, Belén; López-Delgado, Aurora; Fermoso, Javier

2012-04-01

This work reports the effect of pressure on the steam/oxygen gasification at 1000°C of the char derived from low temperature-pressure distillation of granulated scrap tyres (GST). The study was based on the analysis of gas production, carbon conversion, cold gas efficiency and the high heating value (HHV) of the product. For comparison, similar analyses were carried out for the gasification of coals with different rank. In spite of the relatively high ash (≈12 wt.%) and sulphur (≈3 wt.%) contents, the char produced in GST distillation can be regarded as a reasonable solid fuel with a calorific value of 34MJkg(-1). The combustion properties of the char (E(A)≈50 kJ mol(-1)), its temperature of self-heating (≈264°C), ignition temperature (≈459°C) and burn-out temperature (≈676°C) were found to be similar to those of a semi-anthracite. It is observed that the yield, H(2) and CO contents and HHV of the syngas produced from char gasification increase with pressure. At 0.1 MPa, 4.6 Nm(3)kg(char)(-1) of syngas was produced, containing 28%v/v of H(2) and CO and with a HHV around 3.7 MJ Nm(-3). At 1.5 MPa, the syngas yield achieved 4.9N m(3)kg(char)(-1) with 30%v/v of H(2)-CO and HHV of 4.1 MJ Nm(-3). Carbon conversion significantly increased from 87% at 0.1 MPa to 98% at 1.5 MPa. It is shown that the char derived from distillation of granulated scrap tyres can be further gasified to render a gas of considerable heating value, especially when gasification proceeds at high pressure. Copyright © 2011 Elsevier Ltd. All rights reserved.

Pyrolysis of waste animal fats in a fixed-bed reactor: Production and characterization of bio-oil and bio-char

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ben Hassen-Trabelsi, A., E-mail: aidabenhassen@yahoo.fr; Kraiem, T.; Département de Géologie, Université de Tunis, 2092, Tunis

Highlights: • Produced bio-fuels (bio-oil and bio-char) from some animal fatty wastes. • Investigated the effects of main parameters on pyrolysis products distribution. • Determined the suitable conditions for the production of the maximum of bio-oil. • Characterized bio-oils and bio-chars obtained from several animal fatty wastes. - Abstract: Several animal (lamb, poultry and swine) fatty wastes were pyrolyzed under nitrogen, in a laboratory scale fixed-bed reactor and the main products (liquid bio-oil, solid bio-char and syngas) were obtained. The purpose of this study is to produce and characterize bio-oil and bio-char obtained from pyrolysis of animal fatty wastes. Themore » maximum production of bio-oil was achieved at a pyrolysis temperature of 500 °C and a heating rate of 5 °C/min. The chemical (GC–MS analyses) and spectroscopic analyses (FTIR analyses) of bio-oil showed that it is a complex mixture consisting of different classes of organic compounds, i.e., hydrocarbons (alkanes, alkenes, cyclic compounds…etc.), carboxylic acids, aldehydes, ketones, esters,…etc. According to fuel properties, produced bio-oils showed good properties, suitable for its use as an engine fuel or as a potential source for synthetic fuels and chemical feedstock. Obtained bio-chars had low carbon content and high ash content which make them unattractive for as renewable source energy.« less

Chemical structures of swine-manure chars produced under different carbonization conditions investigated by advanced solid-state 13C nuclear magnetic resonance (NMR) spectroscopy

USDA-ARS?s Scientific Manuscript database

Two types of swine manure chars, hydrothermally-produced hydrochar and slow-pyrolysis pyrochar, and their raw swine manure solid were characterized using advanced 13C solid-state nuclear magnetic resonance (NMR) spectroscopy. Compared with the parent raw swine manure, both hydrochars and pyrochar di...

Gasification Characteristics of Coal/Biomass Mixed Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Reginald

2014-09-01

A research project was undertaken that had the overall objective of developing the models needed to accurately predict conversion rates of coal/biomass mixtures to synthesis gas under conditions relevant to a commercially-available coal gasification system configured to co-produce electric power as well as chemicals and liquid fuels. In our efforts to accomplish this goal, experiments were performed in an entrained flow reactor in order to produce coal and biomass chars at high heating rates and temperatures, typical of the heating rates and temperatures fuel particles experience in real systems. Mixed chars derived from coal/biomass mixtures containing up to 50% biomassmore » and the chars of the pure coal and biomass components were subjected to a matrix of reactivity tests in a pressurized thermogravimetric analyzer (TGA) in order to obtain data on mass loss rates as functions of gas temperature, pressure and composition as well as to obtain information on the variations in mass specific surface area during char conversion under kinetically-limited conditions. The experimental data were used as targets when determining the unknown parameters in the chemical reactivity and specific surface area models developed. These parameters included rate coefficients for the reactions in the reaction mechanism, enthalpies of formation and absolute entropies of adsorbed species formed on the carbonaceous surfaces, and pore structure coefficients in the model used to describe how the mass specific surface area of the char varies with conversion. So that the reactivity models can be used at high temperatures when mass transport processes impact char conversion rates, Thiele modulus – effectiveness factor relations were also derived for the reaction mechanisms developed. In addition, the reactivity model and a mode of conversion model were combined in a char-particle gasification model that includes the effects of chemical reaction and diffusion of reactive gases through particle pores and energy exchange between the particle and its environment. This char-particle gasification model is capable of predicting the average mass loss rates, sizes, apparent densities, specific surface areas, and temperatures of the char particles produced when co-firing coal and biomass to the type environments established in entrained flow gasifiers operating at high temperatures and elevated pressures.« less

Study on tar generated from downdraft gasification of oil palm fronds.

PubMed

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

PubMed Central

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study. PMID:24526899

Evaluation of char combustion models: measurement and analysis of variability in char particle size and density

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maloney, Daniel J; Monazam, Esmail R; Casleton, Kent H

Char samples representing a range of combustion conditions and extents of burnout were obtained from a well-characterized laminar flow combustion experiment. Individual particles from the parent coal and char samples were characterized to determine distributions in particle volume, mass, and density at different extent of burnout. The data were then compared with predictions from a comprehensive char combustion model referred to as the char burnout kinetics model (CBK). The data clearly reflect the particle- to-particle heterogeneity of the parent coal and show a significant broadening in the size and density distributions of the chars resulting from both devolatilization and combustion.more » Data for chars prepared in a lower oxygen content environment (6% oxygen by vol.) are consistent with zone II type combustion behavior where most of the combustion is occurring near the particle surface. At higher oxygen contents (12% by vol.), the data show indications of more burning occurring in the particle interior. The CBK model does a good job of predicting the general nature of the development of size and density distributions during burning but the input distribution of particle size and density is critical to obtaining good predictions. A significant reduction in particle size was observed to occur as a result of devolatilization. For comprehensive combustion models to provide accurate predictions, this size reduction phenomenon needs to be included in devolatilization models so that representative char distributions are carried through the calculations.« less

Study on demetalization of sewage sludge by sequential extraction before liquefaction for the production of cleaner bio-oil and bio-char.

PubMed

Leng, Lijian; Yuan, Xingzhong; Shao, Jianguang; Huang, Huajun; Wang, Hou; Li, Hui; Chen, Xiaohong; Zeng, Guangming

2016-01-01

Demetalization of sewage sludge (SS) by sequential extraction before liquefaction was implemented to produce cleaner bio-char and bio-oil. Demetalization steps 1 and 2 did not cause much organic matter loss on SS, and thus the bio-oil and bio-char yields and the compositions of bio-oils were also not affected significantly. However, the demetalization procedures resulted in the production of cleaner bio-chars and bio-oils. The total concentrations and the acid soluble/exchangeable fraction (F1 fraction, the most toxic heavy metal fraction) of heavy metals (Cu, Cr, Pb, Zn, and Cd) in these products were significantly reduced and the environmental risks of these products were also relived considerably compared with those produced from raw SS, respectively. Additionally, these bio-oils had less heavy fractions. Demetalization processes with removal of F1 and F2 fractions of heavy metals would benefit the production of cleaner bio-char and bio-oil by liquefaction of heavy metal abundant biomass like SS. Copyright © 2015 Elsevier Ltd. All rights reserved.

Microbial oxidation of pyrrhotites in coal chars

USGS Publications Warehouse

Miller, K.W.; Risatti, J.B.

1988-01-01

The ability of Thiobacillus ferrooxidans to oxidize pyrrhotite minerals occurring in coal chars was investigated, to evaluate the feasibility of microbial char desulphurization. Bio-oxidation of pyrrhotites in chars produced by two different processes was demonstrated conclusively. Microbial removal of sulphur from a char and its parent coal proceeded at the rate of 3.5% and 12% day-1, respectively with a total of 48% and 81% removal after 27 days. The pH of shake flask cultures containing the coal dropped naturally to a final value of 2.2, while the pH of cultures containing the corresponding char rose and had to be lowered artificially with additional acid. Amending char cultures with elemental sulphur to increase acidity upon bio-oxidation and prevent precipitation of ferric iron was successful; however, the extent of pyrrhotite removal, as demonstated by X-ray diffraction analysis, was not improved. As yet, there is no explanation for the failure of microbial removal of pyrrhotitic sulphur to go to completion. ?? 1988.

Resin char oxidation retardant for composites

NASA Technical Reports Server (NTRS)

Bowles, K. J.; Gluyas, R. E.

1981-01-01

Boron powder stabilizes char, so burned substances are shiny, smooth, and free of loose graphite fibers. Resin weight loss of laminates during burning in air is identical for the first three minutes for unfilled and boron-filled samples, then boron samples stabilize.

Attrition-free pyrolysis to produce bio-oil and char.

PubMed

Mauviel, Guillain; Guillain, Mauviel; Kies, Fairouz; Fairouz, Kies; René, Mar Sans; Mar, Sans Rene; Ferrer, Monique; Monique, Ferrer; Lédé, Jacques; Jacques, Lédé

2009-12-01

Experiments are performed on a laboratory scale setup where beech wood chips are heated by gas convection and walls radiation. This study shows that it is possible to obtain high bio-oil and char yields with relatively low external heat transfer coefficients. The main advantage of this convection/radiation heat transfer mode compared to solid-solid collisions, applied in fluidized bed or twin screw reactors, is the reduction of solid attrition (char and sand). Thus tricky gas-solid separation through hot cyclones and/or hot filters could be avoided or reduced. It should be possible to recover directly bio-oil with less char particles and char free of sand dust. These qualities would allow easier use of these bio-products in different applications.

Low levels of hybridization between sympatric Arctic char (Salvelinus alpinus) and Dolly Varden char (Salvelinus malma) highlights their genetic distinctiveness and ecological segregation.

PubMed

May-McNally, Shannan L; Quinn, Thomas P; Taylor, Eric B

2015-08-01

Understanding the extent of interspecific hybridization and how ecological segregation may influence hybridization requires comprehensively sampling different habitats over a range of life history stages. Arctic char (Salvelinus alpinus) and Dolly Varden (S. malma) are recently diverged salmonid fishes that come into contact in several areas of the North Pacific where they occasionally hybridize. To better quantify the degree of hybridization and ecological segregation between these taxa, we sampled over 700 fish from multiple lake (littoral and profundal) and stream sites in two large, interconnected southwestern Alaskan lakes. Individuals were genotyped at 12 microsatellite markers, and genetic admixture (Q) values generated through Bayesian-based clustering revealed hybridization levels generally lower than reported in a previous study (<0.6% to 5% of samples classified as late-generation hybrids). Dolly Varden and Arctic char tended to make different use of stream habitats with the latter apparently abandoning streams for lake habitats after 2-3 years of age. Our results support the distinct biological species status of Dolly Varden and Arctic char and suggest that ecological segregation may be an important factor limiting opportunities for hybridization and/or the ecological performance of hybrid char.

Low levels of hybridization between sympatric Arctic char (Salvelinus alpinus) and Dolly Varden char (Salvelinus malma) highlights their genetic distinctiveness and ecological segregation

PubMed Central

May-McNally, Shannan L; Quinn, Thomas P; Taylor, Eric B

2015-01-01

Understanding the extent of interspecific hybridization and how ecological segregation may influence hybridization requires comprehensively sampling different habitats over a range of life history stages. Arctic char (Salvelinus alpinus) and Dolly Varden (S. malma) are recently diverged salmonid fishes that come into contact in several areas of the North Pacific where they occasionally hybridize. To better quantify the degree of hybridization and ecological segregation between these taxa, we sampled over 700 fish from multiple lake (littoral and profundal) and stream sites in two large, interconnected southwestern Alaskan lakes. Individuals were genotyped at 12 microsatellite markers, and genetic admixture (Q) values generated through Bayesian-based clustering revealed hybridization levels generally lower than reported in a previous study (<0.6% to 5% of samples classified as late-generation hybrids). Dolly Varden and Arctic char tended to make different use of stream habitats with the latter apparently abandoning streams for lake habitats after 2–3 years of age. Our results support the distinct biological species status of Dolly Varden and Arctic char and suggest that ecological segregation may be an important factor limiting opportunities for hybridization and/or the ecological performance of hybrid char. PMID:26356310

Microwave-assisted pyrolysis of Mississippi coal: A comparative study with conventional pyrolysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdelsayed, Victor; Shekhawat, Dushyant; Smith, Mark W.

Pyrolysis conditions greatly affect the structure-reactivity relationship of char during coal gasification. Here, this work investigated the effect of temperature and microwave heating on the structural properties of the chars generated during pyrolysis, as well as gaseous and tar products. Results showed that microwave pyrolysis of Mississippi coal produced more gaseous products and less tars compared to conventional pyrolysis. Higher CO/CO 2 ratio (>1) was observed under microwave pyrolysis compared to conventional pyrolysis (CO/CO2 < 1), which may be explained by a greater extent of gasification between solid carbon and the CO 2 formed during microwave pyrolysis. Additionally, in microwavemore » pyrolysis, the oil tars generated exhibited lower concentrations of polar oxygenates, while the wax tars showed higher concentrations of non-polar alkanes, as observed from the intensity of CH vibrations in FTIR. The product compositions and FTIR analysis of the tars (oils and waxes) suggest that the microwave interacted preferentially with these polar species, which have relatively higher dielectric properties compared to alkanes. The structure–reactivity relationship of the chars produced was also investigated using a variety of characterization tools such as XRD, BET, SEM, EDS, and FTIR. Finally, the char reactivity towards combustion suggested that microwave-produced chars have a higher thermal stability, likely due to lower O/C ratios, and could be utilized in the metallurgical industry.« less

Microwave-assisted pyrolysis of Mississippi coal: A comparative study with conventional pyrolysis

DOE PAGES

Abdelsayed, Victor; Shekhawat, Dushyant; Smith, Mark W.; ...

2018-01-13

Pyrolysis conditions greatly affect the structure-reactivity relationship of char during coal gasification. Here, this work investigated the effect of temperature and microwave heating on the structural properties of the chars generated during pyrolysis, as well as gaseous and tar products. Results showed that microwave pyrolysis of Mississippi coal produced more gaseous products and less tars compared to conventional pyrolysis. Higher CO/CO 2 ratio (>1) was observed under microwave pyrolysis compared to conventional pyrolysis (CO/CO2 < 1), which may be explained by a greater extent of gasification between solid carbon and the CO 2 formed during microwave pyrolysis. Additionally, in microwavemore » pyrolysis, the oil tars generated exhibited lower concentrations of polar oxygenates, while the wax tars showed higher concentrations of non-polar alkanes, as observed from the intensity of CH vibrations in FTIR. The product compositions and FTIR analysis of the tars (oils and waxes) suggest that the microwave interacted preferentially with these polar species, which have relatively higher dielectric properties compared to alkanes. The structure–reactivity relationship of the chars produced was also investigated using a variety of characterization tools such as XRD, BET, SEM, EDS, and FTIR. Finally, the char reactivity towards combustion suggested that microwave-produced chars have a higher thermal stability, likely due to lower O/C ratios, and could be utilized in the metallurgical industry.« less

Size distribution of carbon layer planes in biochar from different plant type of feedstock with different heating temperatures.

PubMed

Lu, Guan-Yang; Ikeya, Kosuke; Watanabe, Akira

2016-11-01

Biochar application to soil is a strategy to decelerate the increase in the atmospheric carbon concentration. The composition of condensed aromatic clusters appears to be an important determinant of the degradation rate of char in soil. The objective of the present study was to determine the size distribution of carbon layer planes in biochars produced from different types of feedstock (a broadleaf and a coniferous tree and two herbs) using different heating treatment temperatures (HTT; 400 °C-800 °C) using X-ray diffraction 11 band profile analysis. (13)C nuclear magnetic resonance with the phase-adjusted spinning side bands of the chars indicated different spectral features depending on the HTT and similar carbon composition among the plant types at each HTT. Both the content and composition of carbon layer planes in biochar produced using the same HTT were also similar among the plant types. The carbon layer plane size in the 400 °C and 600 °C chars was distributed from 0.24 to 1.68 or 1.92 nm (corresponding to 37 or 52 rings) with the mean size of 0.79-0.92 and 0.80-1.14 nm, respectively. The carbon layer planes in the 800 °C chars ranged from 0.72-0.96 nm (7-14 rings) to 2.64-3.60 nm (91-169 rings) and the mean values were 1.47-1.89 nm. The relative carbon layer plane content in the 600 °C and 800 °C chars was typically 2 and 3 times that in the 400 °C chars. These results indicate the progression of the formation and/or the size development of graphite-like structures, suggesting that a char produced at a higher HTT would have better carbon sequestrating characteristics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solar coal gasification reactor with pyrolysis gas recycle

DOEpatents

Aiman, William R.; Gregg, David W.

1983-01-01

Coal (or other carbonaceous matter, such as biomass) is converted into a duct gas that is substantially free from hydrocarbons. The coal is fed into a solar reactor (10), and solar energy (20) is directed into the reactor onto coal char, creating a gasification front (16) and a pyrolysis front (12). A gasification zone (32) is produced well above the coal level within the reactor. A pyrolysis zone (34) is produced immediately above the coal level. Steam (18), injected into the reactor adjacent to the gasification zone (32), reacts with char to generate product gases. Solar energy supplies the energy for the endothermic steam-char reaction. The hot product gases (38) flow from the gasification zone (32) to the pyrolysis zone (34) to generate hot char. Gases (38) are withdrawn from the pyrolysis zone (34) and reinjected into the region of the reactor adjacent the gasification zone (32). This eliminates hydrocarbons in the gas by steam reformation on the hot char. The product gas (14) is withdrawn from a region of the reactor between the gasification zone (32) and the pyrolysis zone (34). The product gas will be free of tar and other hydrocarbons, and thus be suitable for use in many processes.

Effect of torrefaction on the properties of rice straw high temperature pyrolysis char: Pore structure, aromaticity and gasification activity.

PubMed

Chen, Handing; Chen, Xueli; Qin, Yueqiang; Wei, Juntao; Liu, Haifeng

2017-03-01

The influence of torrefaction on the physicochemical characteristics of char during raw and water washed rice straw pyrolysis at 800-1200°C is investigated. Pore structure, aromaticity and gasification activity of pyrolysis chars are compared between raw and torrefied samples. For raw straw, BET specific surface area decreases with the increased torrefaction temperature at the same pyrolysis temperature and it approximately increases linearly with weight loss during pyrolysis. The different pore structure evolutions relate to the different volatile matters and pore structures between raw and torrefied straw. Torrefaction at higher temperature would bring about a lower graphitization degree of char during pyrolysis of raw straw. Pore structure and carbon crystalline structure evolutions of raw and torrefied water washed straw are different from these of raw straw during pyrolysis. For both raw and water washed straw, CO 2 gasification activities of pyrolysis chars are different between raw and torrefied samples. Copyright © 2016 Elsevier Ltd. All rights reserved.

Charcoal in organic horizon and surface mineral soil in a boreal forest postfire chronosequence of Western Quebec: stocks, depth distribution, chemical properties and a synthesis of related studies

NASA Astrophysics Data System (ADS)

Preston, Caroline M.; Simard, Martin; Bergeron, Yves; Bernard, Guy M.; Wasylishen, Roderick E.

2017-11-01

Wildfires are a major driver of carbon stocks and ecosystem development in Canadian boreal forests, but there is little information on amounts and properties of the charcoal produced. Using data and samples available from a previous study, we determined amounts, depth distribution and chemical properties of visually-determined charcoal (> 2 mm) in a boreal chronosequence in the Abitibi region of Quebec, Canada. Sites ranged from 24 to 2355 years since fire (ysf) and originated from low- and high-severity soil burns (> 5 cm or < 5 cm organic horizon unburned, respectively). Two or three pits were sampled at 1-cm depth intervals from 20 jack pine (Pinus banksiana) sites (one low severity and 19 high severity) and 31 black spruce (Picea mariana) sites (12 low severity and 19 high severity). Site-level charcoal stocks ranged from 50 to 5527 kg ha-1 with high within-site variability and lower stocks for the oldest sites. Depth distributions typically peaked around the organic-mineral interface, but some low-severity sites also had charcoal layers within the organic horizon. Means from 30 samples were 569 mg g-1 total C, 4.1 mg g-1 total N and 140 C/N (molar), with total C and C/N showing a trend of decline with time since fire, and total N showing an increase. Solid-state 13C CPMAS NMR spectra of nine samples showed high variability among the younger samples, but a trend to higher aromaticity for the older ones. A literature survey focusing on boreal forests similarly showed highly variable stocks and chemical properties of charcoal in organic horizon and upper mineral soil, with reduction of variance and lower stocks after several hundred years. This initial variation was also consistent with reports of highly variable temperatures and duration of charring in wildfires. Adding reports available for char production, and considering that most studies of char stocks and production are limited to the organic horizon (forest floor), suggests that initial production of charred material from boreal wildfires might be around 5-10 tonnes ha-1.

Study on the combined sewage sludge pyrolysis and gasification process: mass and energy balance.

PubMed

Wang, Zhonghui; Chen, Dezhen; Song, Xueding; Zhao, Lei

2012-12-01

A combined pyrolysis and gasification process for sewage sludge was studied in this paper for the purpose of its safe disposal with energy self-balance. Three sewage sludge samples with different dry basis lower heat values (LHV(db)) were used to evaluate the constraints on this combined process. Those samples were pre-dried and then pyrolysed within the temperature range of 400-550 degrees C. Afterwards, the char obtained from pyrolysis was gasified to produce fuel gas. The experimental results showed that the char yield ranged between 37.28 and 53.75 wt% of the dry sludge and it changed with ash content, pyrolysis temperature and LHV(db) of the sewage sludge. The gas from char gasification had a LHV around 5.31-5.65 MJ/Nm3, suggesting it can be utilized to supply energy in the sewage sludge drying and pyrolysis process. It was also found that energy balance in the combined process was affected by the LHV(db) of sewage sludge, moisture content and pyrolysis temperature. Higher LHV(db), lower moisture content and higher pyrolysis temperature benefit energy self-balance. For sewage sludge with a moisture content of 80 wt%, LHV(db) of sewage sludge should be higher than 18 MJ/kg and the pyrolysis temperature should be higher than 450 degrees C to maintain energy self-sufficiency when volatile from the pyrolysis process is the only energy supplier; when the LHV(db) was in the range of 14.65-18 MJ/kg, energy self-balance could be maintained in this combined process with fuel gas from char gasification as a supplementary fuel; auxiliary fuel was always needed if the LHV(db) was lower than 14.65 MJ/kg.

Production of carbon molecular sieves from illinois coals. An assessment

USGS Publications Warehouse

Lizzio, Anthony A.; Rostam-Abadi, Massoud

1991-01-01

Chars were produced from an Illinois No. 2 bituminous coal under various pyrolysis and activation conditions and tested for their molecular sieve properties. The amount of N2 compared to the amount of CO2 adsorbed by each char was used as a preliminary indicator of its molecular sieve properties. This relatively simple, but apparently useful test was confirmed by successfully characterizing the well-known molecular sieve properties of a commercial zeolite and molecular sieve carbon. In addition, coal chars having relatively high surface areas (800-1800 m2/g) were produced and tested for their molecular sieving capabilities. These carbon materials, which have high adsorption capacities and relatively narrow pore size distributions, should be ideal candidates for the commercial production of CMS.

Pyrolysis of flax straw: Characterization of char, liquid, and gas as fuel

NASA Astrophysics Data System (ADS)

Tushar, Mohammad Shahed Hasan Khan

The demand for energy continues to outstrip its supply and necessitates the development of renewable energy options. Biomass has been recognized as a major renewable energy source to supplement the declining fossil fuel source of energy. It is the most popular form of renewable energy and, currently, biofuel production is becoming more promising. Being carbon neutral, readily available, and low in sulphur content makes biomass a very promising source of renewable energy. In the present research, both the isothermal and non-isothermal pressurized pyrolysis of flax straw is studied for the first time. In case of isothermal pyrolysis, the influence of pyrolysis temperature and reaction time on char yield and morphology was investigated. The applied pyrolysis temperature was varied between 300 and 500°C. The reaction time was varied from 15 to 60 min. The char yield was found to decrease as pyrolysis temperature and reaction time increased. The char structure and surface morphology were thoroughly investigated by means of x-ray diffraction (XRD), temperature-programmed oxidation (TPO), and scanning electron microscopy (SEM). The degree of porosity and graphitization increased as pyrolysis temperature and time increased. In fact, the experiment performed at 500°C for 1h duration did not yield any char; only residual ash could be obtained. The TPO studies on the char samples corroborated the XRD findings and showed the presence of two types of carbon, namely, amorphous filamentous carbon and graphitic carbon. A thermogravimetric analysis (TGA) of the char was performed to gain an understanding of combustion kinetics and reactivity. It implied that the reactivity of the char decreases as temperature increases, and this finding is well supported by the TPO, TGA, SEM, and XRD characterization data. Furthermore, an empirical global model was devised based on the power law to estimate activation energy and other kinetic parameters. For the non-isothermal pressurized pyrolysis of flax straw, the experiments were carried out at different pressures, ranging from 10 to 40 psig. The three types of products thus obtained (gas, liquid, char) were thoroughly quantified and analyzed. The yields of the products were found to be dependent on the experimental conditions. It was observed that 10 psig of pressure gave the maximum yield of bio-oil, while 20 psig pressure lead to maximum char yield. The gaseous products were analyzed using an online GC, while the bio-oils were characterized using an offline GC/MS. SEM studies were performed to study the char morphology and porosity. The main gaseous products observed were CO, H2, CO2, CH 4, and C3. The bio-oils were mainly composed of phenolic compounds, carboxylic acids, and furfural. The pH and density of the bio-oils was found to increase as pyrolysis pressure increased. SEM investigation gave insights into the porosity of chars; as pressure increased, an increase in the porosity of char was noted. XRD studies showed that amorphous hydrocarbon and graphitic carbons are the major constituents of char, which was supported by TPO experiments. A TGA study showed two reaction zones for char oxidation. The kinetic parameters of oxidation were estimated using a power law model, which was also used for isothermal pyrolysis and isothermal char oxidation kinetics. Based on the data generated, the pressure of 10 psig was found to be optimum for bio-oil production, while a pressure of 20 psig was optimum for char production. With the increase in pressure, the production of individual gas components increased within the pressure range studied. Finally, with the increase in reaction pressure, temperature and time, the produced chars became less reactive.

System and method for producing substitute natural gas from coal

DOEpatents

Hobbs, Raymond [Avondale, AZ

2012-08-07

The present invention provides a system and method for producing substitute natural gas and electricity, while mitigating production of any greenhouse gasses. The system includes a hydrogasification reactor, to form a gas stream including natural gas and a char stream, and an oxygen burner to combust the char material to form carbon oxides. The system also includes an algae farm to convert the carbon oxides to hydrocarbon material and oxygen.

Microwave-induced cracking of pyrolytic tars coupled to microwave pyrolysis for syngas production.

PubMed

Beneroso, D; Bermúdez, J M; Montes-Morán, M A; Arenillas, A; Menéndez, J A

2016-10-01

Herein a new process is proposed to produce a syngas-rich gas fraction (>80vol% H2+CO) from biowaste based on microwave heating within two differentiated steps in order to avoid tars production. The first step consists of the microwave pyrolysis of biowaste induced by a char-based susceptor at 400-800°C; tars, char and syngas-rich gas fractions being produced. The tars are then fed into the second step where a portion of the char from the first step is used as a bed material in a 0.3:1wt% ratio. This bed is heated up by microwaves up to 800°C, allowing thermal cracking of tars and additional syngas (>90vol% H2+CO) being then produced. This new concept arises as an alternative technology to the gasification of biowastes for producing syngas with no need for catalysts or gasifying reagents to minimise tars production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of retorting factors on combustion properties of shale char. 3. Distribution of residual organic matters.

PubMed

Han, Xiangxin; Jiang, Xiumin; Cui, Zhigang; Liu, Jianguo; Yan, Junwei

2010-03-15

Shale char, formed in retort furnaces of oil shale, is classified as a dangerous waste containing several toxic compounds. In order to retort oil shale to produce shale oil as well as treat shale char efficiently and in an environmentally friendly way, a novel kind of comprehensive utilization system was developed to use oil shale for shale oil production, electricity generation (shale char fired) and the extensive application of oil shale ash. For exploring the combustion properties of shale char further, in this paper organic matters within shale chars obtained under different retorting conditions were extracted and identified using a gas chromatography-mass spectrometry (GC-MS) method. Subsequently, the effects of retorting factors, including retorting temperature, residence time, particle size and heating rate, were analyzed in detail. As a result, a retorting condition with a retorting temperature of 460-490 degrees C, residence time of <40 min and a middle particle size was recommended for both keeping nitrogenous organic matters and aromatic hydrocarbons in shale char and improving the yield and quality of shale oil. In addition, shale char obtained under such retorting condition can also be treated efficiently using a circulating fluidized bed technology with fractional combustion. (c) 2009 Elsevier B.V. All rights reserved.

Formation of hydrothermal biochar and char stability in soils

NASA Astrophysics Data System (ADS)

Baumert, Julia; Gleixner, Gerd

2010-05-01

The use of charcoal as an artificial soil additive is suggested to beneficially modify degraded soil, reduce greenhouse gas emission and improve crop yields. So far research has been mainly done using pyrolysis chars which are produced by dry pyrolysis of biomass. Here we used hydrothermal carbonisation (HTC). In this process wet biomass is converted to char at moderate temperatures (~200°C). Due to the exothermal carbonisation reaction this process is almost energy neutral, i.e. the energy needed to start the carbonisation equals the energy released during carbonisation. Different process parameters have been used to modify the properties of the produced chars. We examined the chemical and morphological properties of hydrothermally synthesized biochar. Cellulose, yeast and sucrose were used as model substances for a range of parent material types like organic and garden waste as well as residues from biogas production. By modifying the process conditions of hydrothermal carbonisation concerning temperature (180°C to 220°C) and duration (6 hours to 24 hours) we produced a variety of different biochars. Our findings suggest that the elemental composition and the thermal stability of resulting chars depend on the feedstock and production conditions. Functional group chemistry determined by NMR shows that the aromaticity of the product increases as a function of temperature whereas the amount of O-alkylic compounds declines, concurrently. Our results show that the properties of the biochar can be manipulated by the modification of process conditions. This opens the opportunity to adjust the charcoal to a given soil type.

Century scale char and non-char C co-stabilization in soil free C fractions

NASA Astrophysics Data System (ADS)

Vasilyeva, N. A.; Chenu, C.

2012-04-01

Fate of char particles and reasons of char C stabilization in soils is not well understood especially due to difficulties of its quantification. In this study we showed how char C content could be estimated from elemental analysis along with its size redistribution and co-stabilization with non-char C in long-term. We studied C dynamics in the size and density fractons of soil samples from a historical collection of 80 years bare fallow (no plant input plus tillage) experiment in Versailles, France (1929, 1939, 1949, 1962, 1972, 1991, 2008 years). Coarse char particles were observed in the soil substantially contributing to total organic C. Thus, char C study in this soil was carried out as a nessessary step for estimation of non-char C dynamics. Physical fraction allowed us to follow separately the dynamics of mineral-associated and free C. We analyzed bulk soils, fractions and picked out char particles for C, N and 13C contents. Total organic carbon concentrations in fractions pointed to char C input during 1939-1949 years. After that patterns of C and C/N and δ 13C changes in all fractions suggested redistribution of char C from coarse to finer fractions. Evolution of C/N and δ 13C suggested that all free C fractions, although enriched in char, still contained non-char C in the end of the 80 years C depletion chronosequence. Especially high proportion of non-char C was observed in the silt-size free C fraction. Linear combinations of contrasting char and non-char C C/N values allowed estimation of their proportions from the C/N evolution in the fractions. No substantial admixture of char C was observed for mineral-associated C fractions. Stable C pool in 2008 comprised of 4.6 g C kg-1 soil and was composed of mineral-associated C (3.5 g C kg-1 soil) and char-associated C (1.1 g C kg-1 soil). In both cases organic matter could be stabilized through adsorption and/or occlusion with solid particles (mineral or char). Stabilization capacities of different size class minerals reflected in C concentrations of fractions were 1.2 g C kg-1 for silt-size minerals and 19.4 g C kg-1 for clay-size minerals, contrastingly three orders of magnitude more C was associated with char particles or about 1.2 kg non-char C kg-1 sand-size char and about 1.4 to 3.5 kg non-char C kg-1 silt-size char. Such a high capacity of stabilization by char particles could not be explained by adorbtion alone. In conclusion, combination of C/N and δ13C signature allowed estimation of char content in this soil. Total char C content (sum up of redistributed char C in free fractions) remained not significantly different in the C depletion experiment during five decades after char input. Century scale char and non-char C co-stabilization in this soil could be explained by combination of adsorption and physical protection in microaggregates constructed of mineral and char particles.

Effect of surface area and chemisorbed oxygen on the SO2 adsorption capacity of activated char

USGS Publications Warehouse

Lizzio, A.A.; DeBarr, J.A.

1996-01-01

The objective of this study was to determine whether activated char produced from Illinois coal could be used effectively to remove sulfur dioxide from coal combustion flue gas. Chars were prepared from a high-volatile Illinois bituminous coal under a wide range of pyrolysis and activation conditions. A novel char preparation technique was developed to prepare chars with SO2 adsorption capacities significantly greater than that of a commercial activated carbon. In general, there was no correlation between SO2 adsorption capacity and surface area. Temperature-programmed desorption (TPD) was used to determine the nature and extent of carbon-oxygen (C-O) complexes formed on the char surface. TPD data revealed that SO2 adsorption was inversely proportional to the amount of C-O complex. The formation of a stable C-O complex during char preparation may have served only to occupy carbon sites that were otherwise reactive towards SO2 adsorption. A fleeting C(O) complex formed during SO2 adsorption is postulated to be the reaction intermediate necessary for conversion of SO2 to H2SO4. Copyright ?? 1996 Elsevier Science Ltd.

Degradation of p-Nitrophenol by Lignin and Cellulose Chars: H2O2-Mediated Reaction and Direct Reaction with the Char.

PubMed

Yang, Jing; Pignatello, Joseph J; Pan, Bo; Xing, Baoshan

2017-08-15

Chars and other black carbons are reactive toward certain compounds. Such reactivity has been attributed to reduction of O 2 by persistent free radicals in the solid to H 2 O 2 , which then back-reacts with the solid to generate reactive oxygen species (ROS; especially HO • ). We studied the decomposition of p-nitrophenol (PNP) by pure lignin and cellulose chars aged in moist air or a vacuum at room temperature for up to a month. In air, the chars chemisorbed oxygen, a portion of which was liberated as H 2 O 2 when the char was submerged in water. The evolved H 2 O 2 was simultaneously decomposed by the char. PNP reacted predominantly in the sorbed state and only reduction products (phenol, catechol) were identified. Aging the char in air sharply (within hours) reduced H 2 O 2 -producing capacity and free radical concentration, but more gradually reduced PNP decay rate over the month-long period. PNP decay was only modestly suppressed (12-30%) by H 2 O 2 removal (catalase), and had little effect on the free radical signal (<6 radicals annihilated per 1000 PNP reacted). Contrasting with previous studies, the results show that direct reaction of PNP with char predominates over H 2 O 2 -dependent reactions, and the vast majority of direct-reacting sites are nonradical in character. Nonradical sites are also responsible in part for H 2 O 2 decomposition; in fact, H 2 O 2 pretreatment depleted PNP reactive sites. Lignin char was generally more reactive than cellulose char. The Fe impurity in lignin played no role. The results are relevant to the fate of pollutants in black carbon-rich environments and the use of carbons in remediation.

Comparison of biochar formation from various agricultural by-products using FTIR spectroscopy

USDA-ARS?s Scientific Manuscript database

Biochar is charred material produced by the pyrolysis of organic biomass. In this work, Fourier transform infrared (FTIR) spectra of different agricultural by-products feedstock and their derived biochars were collected to explore the potential of FTIR technique as a simple and rapid method for char...

Characteristics of the microwave pyrolysis and microwave CO2-assisted gasification of dewatered sewage sludge.

PubMed

Chun, Young Nam; Jeong, Byeo Ri

2017-07-28

Microwave drying-pyrolysis or drying-gasification characteristics were examined to convert sewage sludge into energy and resources. The gasification was carried out with carbon dioxide as a gasifying agent. The examination results were compared with those of the conventional heating-type electric furnace to compare both product characteristics. Through the pyrolysis or gasification, gas, tar, and char were generated as products. The produced gas was the largest component of each process, followed by the sludge char and the tar. During the pyrolysis process, the main components of the produced gas were hydrogen and carbon monoxide, with a small amount of hydrocarbons such as methane and ethylene. In the gasification process, however, the amount of carbon monoxide was greater than the amount of hydrogen. In microwave gasification, a large amount of heavy tar was produced. The largest amount of benzene in light tar was generated from the pyrolysis or gasification. Ammonia and hydrogen cyanide, which are precursors of NO x , were also generated. In the microwave heating method, the sludge char produced by pyrolysis and gasification had pores in the mesopore range. This could be explained that the gas obtained from the microwave pyrolysis or gasification of the wet sewage sludge can be used as an alternative fuel, but the tar and NO x precursors in the produced gas should be treated. Sludge char can be used as a biomass solid fuel or as a tar removal adsorbent if necessary.

Comparing Effects of Feedstock and Run Conditions on Pyrolysis Products Produced at Pilot-Scale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunning, Timothy C; Gaston, Katherine R; Wilcox, Esther

2018-01-19

Fast pyrolysis is a promising pathway for mass production of liquid transportable biofuels. The Thermochemical Process Development Unit (TCPDU) pilot plant at NREL is conducting research to support the Bioenergy Technologies Office's 2017 goal of a $3 per gallon biofuel. In preparation for down select of feedstock and run conditions, four different feedstocks were run at three different run conditions. The products produced were characterized extensively. Hot pyrolysis vapors and light gasses were analyzed on a slip stream, and oil and char samples were characterized post run.

Determination of alkylphenols in eluates from pyrolysis solid residues using dispersive liquid-liquid microextraction.

PubMed

Bernardo, M; Gonçalves, M; Lapa, N; Mendes, B

2010-05-01

Dispersive liquid-liquid microextraction (DLLME) coupled with gas chromatography-mass spectrometry (GC-MS) was applied for the determination of 11 alkylphenols in eluates of chars produced in the co-pyrolysis of different wastes. The optimized DLLME procedure, 4 mL of sample solution, 15 microL of trichloroethylene as extraction solvent, 1 mL of acetone as dispersion solvent and addition of 15% (w/v) of NaCl, was validated. Under the optimum conditions, the enrichment factors were in the range of 82-180. Calibration curves were constructed for each analyte in pure water in the concentration range of 0.5-8 microg/L with correlation coefficients higher than 0.999. The limits of detection were between 0.07 and 0.17 microg/L. The repeatability of the method was evaluated using water samples fortified with the analyte mixture at two concentration levels: the relative standard deviation (RSD) values were between 3.7% and 8.0% for a concentration of 0.5 microg/L, and between 4.2% and 6.4% for a concentration of 3 microg/L. The recoveries of the analytes evaluated by fortification of real eluate samples were in the range of 67.9-97.9% for eluate 1 (obtained from a decontaminated char) and in the range of 61.9-101.4% for eluate 2 (obtained from the untreated char). o-Methylphenol presented low recoveries for both eluates showing a possible matrix effect. The results obtained show that this method is adequate for the determination of alkylphenols in environmental aqueous samples and presents itself as a fast and inexpensive technique, using minor amounts of organic solvents. Copyright (c) 2010. Published by Elsevier Ltd.

A burnout prediction model based around char morphology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tao Wu; Edward Lester; Michael Cloke

Several combustion models have been developed that can make predictions about coal burnout and burnout potential. Most of these kinetic models require standard parameters such as volatile content and particle size to make a burnout prediction. This article presents a new model called the char burnout (ChB) model, which also uses detailed information about char morphology in its prediction. The input data to the model is based on information derived from two different image analysis techniques. One technique generates characterization data from real char samples, and the other predicts char types based on characterization data from image analysis of coalmore » particles. The pyrolyzed chars in this study were created in a drop tube furnace operating at 1300{sup o}C, 200 ms, and 1% oxygen. Modeling results were compared with a different carbon burnout kinetic model as well as the actual burnout data from refiring the same chars in a drop tube furnace operating at 1300{sup o}C, 5% oxygen, and residence times of 200, 400, and 600 ms. A good agreement between ChB model and experimental data indicates that the inclusion of char morphology in combustion models could well improve model predictions. 38 refs., 5 figs., 6 tabs.« less

Leaching of major and trace elements from paper-plastic gasification chars: an experimental and modelling study.

PubMed

Fuente-Cuesta, A; Lopez-Anton, M A; Diaz-Somoano, M; Zomeren, A van; Cieplik, M; Martínez-Tarazona, M R

2013-01-15

The control of soluble metal species in the sub-product leachate generated in electricity production processes is of great concern from an environmental and health point of view. Unlike fly ash, the leaching behaviour of char materials has received little attention. Yet, these solids are captured together with fly ashes in the particle control devices of power plants and are emitted in the same way as by-products. The present study was carried out using two char samples: (i) a raw char and (ii) the same type of char employed in a previous study so that it could serve as a sorbent for mercury species in gas phase. The char samples were by-products (residues) that had been generated during the gasification of plastic and paper waste. The leachates were analyzed for the following elements: Al, Ca, Si, Mg, Ba, Cu, Ni, Pb, Zn, Mo and Hg. In addition, geochemical modelling of the leaching test results was employed to identify the underlying chemical processes that led to the release of toxic elements. The results showed that at alkaline pH values, sorption on the solid surfaces of the char was negligible due to the inorganic complexation of cations in the solution. When the char was used as mercury sorbent slight changes occurred on the reactive surface resulting in the modification of the binding of some elements. As the pH increased, complexation with dissolved organic matter played a more important role in the case of some elements such as Cu because of the greater concentration of dissolved organic matter in solution. Copyright © 2012 Elsevier B.V. All rights reserved.

Pulsed Laser Annealing of Carbon

NASA Astrophysics Data System (ADS)

Abrahamson, Joseph P.

This dissertation investigates laser heating of carbon materials. The carbon industry has been annealing carbon via traditional furnace heating since at least 1800, when Sir Humphry Davy produced an electric arc with carbon electrodes made from carbonized wood. Much knowledge has been accumulated about carbon since then and carbon materials have become instrumental both scientifically and technologically. However, to this day the kinetics of annealing are not known due to the slow heating and cooling rates of furnaces. Additionally, consensus has yet to be reached on the cause of nongraphitizability. Annealing trajectories with respect to time at temperature are observed from a commercial carbon black (R250), model graphitizable carbon (anthracene coke) and a model nongraphitizable carbon (sucrose char) via rapid laser heating. Materials were heated with 1064 nm and 10.6 im laser radiation from a Q-switched Nd:YAG laser and a continuous wave CO2 laser, respectively. A pulse generator was used reduce the CO2 laser pulse width and provide high temporal control. Time-temperature-histories with nanosecond temporal resolution and temperature reproducibility within tens of degrees Celsius were determined by spectrally resolving the laser induced incandescence signal and applying multiwavelength pyrometry. The Nd:YAG laser fluences include: 25, 50, 100, 200, 300, and 550 mJ/cm2. The maximum observed temperature ranged from 2,400 °C to the C2 sublimation temperature of 4,180 °C. The CO2 laser was used to collect a series of isothermal (1,200 and 2,600 °C) heat treatments versus time (100 milliseconds to 30 seconds). Laser heated samples are compared to furnace annealing at 1,200 and 2,600 °C for 1 hour. The material transformation trajectory of Nd:YAG laser heated carbon is different than traditional furnace heating. The traditional furnace annealing pathway is followed for CO2 laser heating as based upon equivalent end structures. The nanostructure of sucrose char after 5 seconds of isothermal annealing at 2,600 °C is comprised almost entirely of quasi-spherical closed shell particles that are free of sp3 and oxygen content. With additional time at temperature the particles unravel and propagative particle opening occurs throughout the material. The irregular pore structure found in the end product is a result of particle unraveling. The structures found in heat treated sucrose char believed to contain odd membered rings are not manufactured during the annealing process due to impinging growth of stacks. Thus, odd membered rings are likely present in the starting non-graphitizable char. Furnace annealing of cokes and chars produced from: oxygen containing compounds (polyfurfuryl alcohol and anthanthrone), from a five membered ring containing polyaromatic hydrocarbon (fluorene), and from sulfur containing decant oil and a blend of anthracene-dibenzothiophene were compared to furnace annealed anthracene coke and sucrose char. The majority of initial oxygen content evolved out during low temperature carbonization. The intermediate species formed after oxygen evolution dictated the resulting carbon skeleton and thus the graphitizability. Carbonization of anthanthrone resulted in a graphitizable coke. It is proposed that carbon monoxide loss from anthanthrone results in the formation of perylene. An obvious resemblance was observed in structure between heat treated sucrose and polyfurfuryl alcohol char as compared to heated treated char embedded with 5 membered rings via carbonization of fluorene. Thus, providing evidence that 5 membered rings are present in the virgin chars and are the cause of non-graphitizability. The heteroatom sulfur effects carbon structure in a different way as compared to oxygen. Sulfur is thermally stable in carbon up to ˜ 1,000 °C and thus plays little role in the initial low temperature (500 °C) carbonization. As such it imparts a relatively unobservable impact on nanostructure, but rather acts to cause micro-cracks upon rapid evolution in the form of H2S and CS2, upon subsequent heat treatment. Laboratory generated synthetic soot from benzene and benzene-thiophene were Nd:YAG laser and furnace annealed. Furnace annealing of sulfur doped synthetic soot results in cracks and rupturing due to the high pressures caused by explosive sulfur evolution at elevated temperature. Whereas Nd:YAG laser heating of the sulfur doped sample acted to induce curvature. The observed curvature is owed to annealing occurring simultaneously with sulfur evolution. The unset lamellae are strongly influenced by the defect formed upon sulfur evolution. Coke and char samples were prepared via carbonization in sealed tubing reactors. The extent of mesophase development was assessed by measuring the materials optical anisotropy with a polarized light microscope. Physical and chemical transformations from annealing were measured with electron microscopy, energy dispersive X-ray spectroscopy, selected area electron diffraction, and electron energy loss spectroscopy. Virgin samples and traditional furnace annealed samples available in bulk were analyzed with X-ray diffraction. The potential technological importance of laser annealing carbon is demonstrated as annealing can be performed continuously and rapidly. Examples of material processing and synthesis not possible via traditional furnace annealing are provided.

Physicochemical and adsorptive properties of fast-pyrolysis bio-chars and their steam activated counterparts

USDA-ARS?s Scientific Manuscript database

Fast pyrolysis is rapid heating in the absence of oxygen resulting in decomposition of organic material. When applied to biomass, it produces bio-oil, bio-char and gas. The Agricultural Research Service (ARS) of the USDA has studied fluidized-bed fast pyrolysis of several bimoass including perenni...

Combustion and gasification characteristics of chars from four commercially significant coals of different rank. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nsakala, N.Y.; Patel, R.L.; Lao, T.C.

1982-09-01

The combustion and gasification kinetics of four size graded coal chars were investigated experimentally in Combustion Engineering's Drop Tube Furnace System (DTFS). The chars were prepared in the DTFS from commercially significant coals representing a wide range of rank; these included a Pittsburgh No. 8 Seam hvAb coal, an Illinois No. 6 Seam hvCb coal, a Wyoming Sub C, and a Texas Lignite A. Additionally, a number of standard ASTM and special bench scale tests were performed on the coals and chars to characterize their physicochemical properties. Results showed that the lower rank coal chars were more reactive than themore » higher rank coal chars and that combustion reactions of chars were much faster than the corresponding gasification reactions. Fuel properties, temperature, and reactant gas partial pressure had a significant influence on both combustion and gasification, and particle size had a mild but discernible influence on gasification. Fuel reactivities were closely related to pore structure. Computer simulation of the combustion and gasification performances of the subject samples in the DTFS supported the experimental findings.« less

Design of pyrolysis reactor for production of bio-oil and bio-char simultaneously

NASA Astrophysics Data System (ADS)

Aladin, Andi; Alwi, Ratna Surya; Syarif, Takdir

2017-05-01

The residues from the wood industry are the main contributors to biomass waste in Indonesia. The conventional pyrolysis process, which needs a large energy as well as to produce various toxic chemical to the environment. Therefore, a pyrolysis unit on the laboratory scale was designed that can be a good alternative to achieve zero-waste and low energy cost. In this paper attempts to discuss design and system of pyrolysis reactor to produce bio-oil and bio-char simultaneously.

Production of carbon molecular sieves from Illinois coal

USGS Publications Warehouse

Lizzio, A.A.; Rostam-Abadi, M.

1993-01-01

Carbon molecular sieves (CMS) have become an increasingly important class of adsorbents for application in the separation of gas molecules that vary in size and shape. A study is in progress at the Illinois State Geological Survey to determine whether Illinois basin coals are suitable feedstocks for the production of CMS and to evaluate their potential application in gas separation processes of commercial importance. Chars were prepared from Illinois coal in a fixed-bed reactor under a wide range of heat treatment and activation conditions. The effects of various coal/char pretreatments, including coal demineralization, preoxidation, char activation, and carbon deposition, on the molecular sieve properties of the chars were also investigated. Chars with commercially significant BET surface areas of 1500 m2/g were produced by chemical activation using potassium hydroxide as the activant. These high-surface-area (HSA) chars had more than twice the adsorption capacity of commercial carbon and zeolite molecular sieves. The kinetics of adsorption of various gases, e.g., N2, O2, CO2, CH4, CO and H2, on these chars at 25??C was measured. The O2/N2 molecular sieve properties of one char prepared without chemical activation were similar to those of a commercial CMS. On the other hand, the O2/N2 selectivity of the HSA char was comparable to that of a commercial activated carbon, i.e., essentially unity. Carbon deposition, using methane as the cracking gas, increased the O2/N2 selectivity of the HSA char, but significantly decreased its adsorption capacity. Several chars showed good potential for efficient CO2/CH4 separation; both a relatively high CO2 adsorption capacity and CO2/CH4 selectivity were achieved. The micropore size distribution of selected chars was estimated by equilibrium adsorption of carbon dioxide, n-butane and iso-butane at O??C. The extent of adsorption of each gas corresponded to the effective surface area contained in pores with diameters greater than 3.3, 4.3 and 5.0 A??, respectively. Kinetic and equilibrium adsorption data provided complementary information on the molecular sieving capabilities and microstructure of the prepared chars. ?? 1993.

Biochemical stability of sewage sludge chars and their impact on soil organic matter of a Mediterranean Cambisol

NASA Astrophysics Data System (ADS)

Paneque, Marina; María De la Rosa, José; Aragón, Carlos; Kern, Jürgen; Knicker, Heike

2016-04-01

Transformation of sewage sludge (SS) into char achieves sludge hygienisation, which is necessary prior its application into agricultural soils. The pyrolysis of SS increases its stability in a degree which depends on the thermal treatment used. Thus, chars produced by using hydrothermal carbonization are typically more stable than normal soil organic matter (SOM), but less stable than chars from dry pyrolysis (Libra et al., 2011). Addition of highly-recalcitrant SS-chars to soil will likely increase its carbon sequestration potential; however the fertilizing properties of SS may be compromised due to its alteration during the pyrolysis. The main goal of this work was to investigate the biochemical recalcitrance of two 13C-enriched SS-chars once applied in a Mediterranean Cambisol as well as to evaluate their impact on the SOM quality and carbon stability. Thus, we studied the distribution of 13C between plants and soil after the addition of the 13C-enriched chars (2 atm%) to the soil. Therefore, we performed a greenhouse incubation experiment, using a Mediterranean Cambisol as matrix and tested the following treatments: control (soil alone), raw SS, SS-hydrochar, SS-pyrochar. The SS was produced in a pilot-scale waste-water plant and enriched with 13C by the addition of 13C-glucose during the treatment. The amendment was only applied to the upper 2 cm of the soil matrix where it accounted for 5% of its dry weight. Per pot, 25 seeds of Lolium perenne were sowed and incubated under controlled conditions. The biomass production as well as the concentration of 13C in leaves and roots was determined after 1, 2 and 5 months. The partitioning of the 13C between soil and plant and its transformation into bioavailable forms were monitored by stable isotopic mass spectrometry. The 13C-enrichment of the chars allowed the use of solid-state 13C NMR spectroscopy as a means for the detection of chemical alterations of the chars during their aging. Libra J., Ro K., Kammann C., Funke A., Berge N., Neubauer Y., Titirici M., Fuhner C., Bens O., Kern J., Emmerich K. (2011) Hydrothermal carbonization of biomass residuals: a comparative review of the chemistry, processes and applications of wet and dry pyrolysis. Biofuels, 2 (1), 89-124.

Modified thermal-optical analysis using spectral absorption selectivity to distinguish black carbon from pyrolized organic carbon.

PubMed

Hadley, Odelle L; Corrigan, Craig E; Kirchstetter, Thomas W

2008-11-15

This study presents a method for analyzing the black carbon (BC) mass loading on a quartz fiber filter using a modified thermal-optical analysis method, wherein light transmitted through the sample is measured over a spectral region instead of at a single wavelength. Evolution of the spectral light transmission signal depends on the relative amounts of light-absorbing BC and char, the latter of which forms when organic carbon in the sample pyrolyzes during heating. Absorption selectivities of BC and char are found to be distinct and are used to apportion the amount of light attenuated by each component in the sample. Light attenuation is converted to mass concentration on the basis of derived mass attenuation efficiencies (MAEs) of BC and char. The fractions of attenuation due to each component are scaled by their individual MAE values and added together as the total mass of light absorbing carbon (LAC). An iterative algorithm is used to find the MAE values for both BC and char that provide the best fit to the carbon mass remaining on the filter (derived from direct measurements of thermally evolved CO2) at temperatures higher than 480 degrees C. This method was applied to measure the BC concentration in precipitation samples collected in northern California. The uncertainty in the measured BC concentration of samples that contained a high concentration of organics susceptible to char ranged from 12% to 100%, depending on the mass loading of BC on the filter. The lower detection limit for this method was approximately 0.35 microg of BC, and the uncertainty approached 20% for BC mass loading greater than 1.0 microg of BC.

Microanalysis of vitrous char and associated polymers: reference and ancient assemblages

NASA Astrophysics Data System (ADS)

Allue, E.; Bonnamy, S.; Courty, M. M.; Gispert I Guirado, F.

2012-12-01

Formation of vitrous char that occur in ancient charcoal assemblages have remained unsolved. Laboratory experiments refuted vitrification to resulting from high temperature charring of green or resinous wood. This puzzling problem has been refreshed by showing the association to the charcoal and vitrous char of plastics that were originally supposed to only be produced by petroleum industry. Extraction of similar polymers within geological glassy products from cosmic airbursts has suggested impact processes to possibly forming the carbonaceous polymorphs. The pulverisation at the ground in the Angles village (French Eastern Pyrenees) following the 2011 August 2nd high altitude meteor explosion of exotic debris with vitrous char and polymers, just alike the puzzling ones of the geological and archaeological records, has provided potential reference materials. We present here their microanalysis by Environmental SEM with EDS, Raman micro-spectrometry and FTIR, XRD, TEM, ICP-MS and isotope analyses. The characterization helps elucidating how the carbonaceous polymorphs formed by transient heating and transient high pressure of atmospheric aerosols. Under TEM the vesicular, dense, vitrous char show high structural organization with a dense pattern of nano-sized graphitized domains, metals and mineral inclusions. The coupled Raman-ESEM has allowed identifying a complex pattern at micro scales of ordered "D" peak at 1320-1350 cm-1 and the graphitic, ordered peak at 1576-1590 cm-1, in association to amorphous and poorly graphitic ordered carbon. The later occurs within plant cells that have been extracted from the dense vitrous char by performing controlled combustion under nitrogen up to 1000°C. In contrast, the brittle, vesicular vitrous char and the polymers encountered at the rear of the pulverised airburst debris reveal to be formed of agglutinated micro spherules of amorphous carbon with rare crystallized carbon nano-domains and scattered mineral inclusions. They completely vaporised at 300°C under stepped-heating without leaving extractable residues. The link established between the structure of these exceptional carbon polymorphs and their forming processes provide diagnostic keys for interpreting vitrous carbon in ancient charcoal assemblage. The hardest ones offer reliable impact markers with their distinctive nanostructure produced by the transient high pressure and heating of carbonaceous aerosols by cosmic airbursts. In contrast, the weakly graphitised ones with distinctive plant structures would possibly express moderate effects of the airburst shock wave on vegetation at the ground. Thus micro-structural characterization of charcoal in archaeological assemblages would help tracing possible exploitation of blasted wood forest and related fossil fuel produced by ancient cosmic airbursts.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bozkurt, Y.; Misirlioglu, Z.; Sinag, A.

The reactivities of chars obtained by pyrolysis of Bursa Mustafa Kemal Pasa Alpagut lignite and Balkesir Dursunbey Cakiirca lignite (Turkey) at different temperatures were determined by CO{sub 2} gasification and by combustion with O{sub 2}. Catalytic effect of Na{sub 2}CO{sub 3} on the CO{sub 2} and O{sub 2} gasification reactivity of chars was investigated. Gasification tests were performed in the fixed bed reactors operating at ambient pressure. Reactivity of chars during the CO{sub 2} gasification reactions was determined by calculating the reaction rate constants and reactivity of chars during the O{sub 2} gasification was determined by using ignition temperatures ofmore » the samples. Activation energies and Arrhenius constants of the chars on the CO{sub 2} gasification reactions were also calculated by the help of Arrhenius curves. The activation energy for CO{sub 2} gasification was generally decreased with pyrolysis temperature, due to the different surface characteristics and different nature of carbon atoms gasified as the gasification reactions proceed. Generally, the increase in pyrolysis temperature leads to an increase in gasification reactivity with CO{sub 2}. The reactivity of chars in catalytic gasification was higher than the corresponding non-catalytic reactivity of the same chars. Ignition temperature increased with increasing pyrolysis temperature.« less

Time resolved quantitative imaging of charring in materials at temperatures above 1000 K

NASA Astrophysics Data System (ADS)

Böhrk, Hannah; Jemmali, Raouf

2016-07-01

A device is presented allowing for in situ investigation of chemically changing materials by means of X-ray imaging. A representative cork ablator sample, additionally instrumented with thermocouples, is encapsulated in an evacuated cell heating a sample surface with a heat flux of 230 kW/m2. The images show the sample surface and the in-depth progression of the char front dividing the char layer from the virgin material. Correlating the images to thermocouple data allows for the deduction of a reaction temperature. For the representative cork ablator investigated at the present conditions, the progression rate of the pyrolysis layer is determined to 0.0285 mm/s and pyrolysis temperature is 770 or 737 K, depending on the pre-existing conditions. It is found that the novel device is ideally suited for volume process imaging.

Devolatilization of coal particles in a flat flame -- Experimental and modeling study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Therssen, E.; Gourichon, L.; Delfosse, L.

1995-10-01

Pulverized coals have been tested under the conditions of industrial flames, with high heating rate and high temperatures. The chars were collected after different pyrolysis times. For eight coals, the devolatilized fraction of coal has been measured, as well as those of carbon, hydrogen and nitrogen. During pyrolysis, the evolution of the texture of the grains has been studied by measurement of their microporous surface area, which undergoes a large increase, depending on coal rank. The composition of the volatiles, as deduced from the ultimate and proximate analysis of chars, showed high volatile bituminous coals to essentially produce tars withmore » an aromatic structure. Low and medium volatile bituminous coals produced light hydrocarbons on devolatilization and the char`s surface area continued increasing slowly during the whole of devolatilization, according to the slow increase of the fraction of hydrogen devolatilized. The char`s reactivity with oxygen was followed by measurements of Active Surface Area (ASA). It was shown that the ASA continuously decreases during devolatilization. Five models of devolatilization in the literature were tested and compared to the experimental results, assuming first-order reactions with respect to the remaining volatile matter. Badzioch`s model correctly fitted the experimental results and values of the rate constant obtained by computer trial and error adjustment were higher for lower ranks of the four bituminous coals. Anthony`s model also fits the measurements, provided an adjustment of the preexponential factor of activation energy for which it is shown that an infinite number of such pairs is suitable. If the model is run isothermally at the flame`s peak temperature, it also correctly fits the experimental results.« less

Process for converting coal into liquid fuel and metallurgical coke

DOEpatents

Wolfe, Richard A.; Im, Chang J.; Wright, Robert E.

1994-01-01

A method of recovering coal liquids and producing metallurgical coke utilizes low ash, low sulfur coal as a parent for a coal char formed by pyrolysis with a volatile content of less than 8%. The char is briquetted and heated in an inert gas over a prescribed heat history to yield a high strength briquette with less than 2% volatile content.

Linear lesions in heart tissue using diffused laser radiation

NASA Astrophysics Data System (ADS)

Fried, Nathaniel M.; Lardo, Albert C.; Berger, Ronald D.; Calkins, Hugh; Halperin, Henry R.

2000-05-01

Transmural, continuous, and linear lesions may be necessary for successful catheter ablation of cardiac arrythmias such as atrial fibrillation. Laser ablation was studied as an alternative to radiofrequency ablation, which is noted to produce superficial and discontinuous lesions as well as tissue charring and vaporization. Samples of canine myocardium were placed in a saline bath and irradiated with an 1.06- micrometer Nd:YAG laser operated in either pulsed or continuous mode. For pulsed mode, the laser pulse duration was 10 s with 10 s cooling between pulses. Laser radiation was delivered radially through diffusing optical fiber tips oriented parallel to the endocardial surface. In CW mode, transmural (6-mm-deep), linear (16-mm-long), and continuous lesions were produced using a laser power of 30 W and an irradiation time of 180 s. Peak tissue temperatures measured 51 plus or minus 1 degree Celsius at the endocardial surface, 61 plus or minus 6 degrees Celsius in the mid-myocardium, and 55 plus or minus 6 degree Celsius at the epicardial surface. There was no evidence of tissue charring or vaporization. Pulsed laser irradiation produced comparable lesion depths to CW irradiation with more uniform heating of the subsurface myocardium, but at the expense of longer operation times. Further in vivo study of laser ablation is warranted for possible clinical applications.

The influence of composition and final pyrolysis temperature variations on global kinetics of combustion of segregated municipal solid waste

NASA Astrophysics Data System (ADS)

Pranoto; Himawanto, D. A.; Arifin, N. A.

2017-04-01

The combustion of segregated municipal solid waste (MSW) and the resulted char from the pyrolysis process were investigated in this research. The segregated MSW that was collected and used can be divided into organic and inorganic waste materials. The organic materials were bamboo and banana leaves and the inorganic materials were Styrofoam and snack wrappings. The composition ratio of the waste was based on the percentage of weight of each sample. The thermal behaviour of the segregated MSW was investigated by thermo gravimetric analysis. For the pyrolysis process the prepared samples of 200gram were heated from ambient temperature until a variance of final pyrolysis temperature of 550°C, 650°C and 750°C at a constant heating rate of 25°C/min. It was found that the highest activation energy of the raw materials is achieved from sample CC1 (Char with 100% inorganic materials). The activation energy of the raw materials is relatively lower than that of the char. The higher the final pyrolysis temperature, the lower the calorific value of char. The calorific value gradually increases with the amount of inorganic materials.

Proximate analyses and predicting HHV of chars obtained from cocracking of petroleum vacuum residue with coal, plastics and biomass.

PubMed

Ahmaruzzaman, M

2008-07-01

Higher heating value (HHV) and analysis of chars obtained from cocracking of petroleum vacuum residue (XVR) with coal (SC), biomass (BG, CL) and plastics (PP, PS, BL) are important which define the energy content and determine the clean and efficient use of these chars. The main aim of the present study is to analyze the char obtained from cocracking in terms of their proximate analysis data and determination of the HHV of the chars. The char obtained from XVR+PP cocracking showed a HHV of 32.84 MJ/kg, whereas that from CL cracking showed a HHV of 18.52 MJ/kg. The experimentally determined heating values of the char samples obtained from cocracking have been correlated with the theoretical equation based on proximate analysis data. There exists a variety of correlations for predicting HHV from proximate analysis of fuels. Based upon proximate analysis data, the models were tested. The best results show coefficient of determination (R2) of 0.965 and average absolute and bias error of 3.07% and 0.41%, respectively. The heating values obtained from the model were in good agreement with that obtained by experiment. Proximate analysis of the chars obtained from the cocracking of XVR with coal, biomass and plastics showed that there exists a definite interaction of the reactive species, when they were cocracked together.

Type of litter determines the formation and properties of charred material during wildfires

NASA Astrophysics Data System (ADS)

Chavez, Bruno; Fonturbel, M. Teresa; Salgado, Josefa; García-Oliva, Felipe; Vega, Jose A.; Merino, Agustin

2014-05-01

Wildfire is one of the most important disturbances all over the World, affecting both the amount and composition of forest floor and mineral soils. In comparison with unburnt areas, wildfire-affected forest floor usually shows lower contents of labile C compounds and higher concentrations of recalcitrant aromatic forms. These changes in composition can have important impact on biogeochemical cycles and therefore ecosystem functions. Although burning of different types of litter can lead to different amount and types of pyrogenic compounds, this aspect has not been evaluated yet. The effect of wildfire on SOM composition and stability were evaluated in five major types of non-wood litter in Mediterranean ecosystems: Pinus nigra, E. arborea, P. pinaster, U. europaeus and Eucalyptus globulus. In each of these ecosystems, forest floor samples from different soil burn severities were sampled. Soil burnt severities were based on visual signs of changes in forest floor and deposition of ash. Pyrogenic carbon quality were analysed using elementary analysis, solid-state 13 C nuclear magnetic resonance spectroscopy, Reflectance Infrared Fourier Transform (FTIR) and thermal analysis (simultaneous DSC-TG). The study showed that the different types of litter influenced the formation and characteristics of charred material. They differed in the temperature at which they start to be formed, the amounts of charred compounds and in their chemical composition. The resulting charred materials from the different litter, showed an important variability in the degree of carbonitation/aromatization. Unlike the biochar obtained through pyrolysis of woody sources, which contains exclusively aromatic structures, in the charred material produced in some litter, lignin, cellulose and even cellulose persist even in the high soil burnt severity. Coinciding with increases in aromatic contents, important decreases in atomic H/C and O/C ratios were recorded. However, the values found in some litters, were higher than 0.5, suggesting that low degree of carbonization/aromatization. Although burning also led to compounds of higher thermal recalcitrance (increases in T50 values), values recorded in some litters were lower than those measured in highly polycondensed aromatic compounds. The differences found among the different forest floor cannot be only attributable to the initial SOM composition of the litter. Other aspects, such as the different thermal sensitivity, flammability and different conditions during wildfire (temperatures, combustion duration, oxygen concentrations) could also have contributed.

Removal of Cu(II) from acidic electroplating effluent by biochars generated from crop straws.

PubMed

Tong, Xuejiao; Xu, Renkou

2013-04-01

The removal efficiency of copper (Cu(II)) from an actual acidic electroplating effluent by biochars generated from canola, rice, soybean and peanut straws was investigated. The biochars simultaneously removed Cu(II) from the effluent, mainly through the mechanisms of adsorption and precipitation, and neutralized its acidity. The removal efficiency of Cu(II) by the biochars followed the order: peanut straw char > soybean straw char > canola straw char > rice straw char > a commercial activated carbonaceous material, which is consistent with the alkalinity of the biochars. The pH of the effluent was a key factor determining the removal efficiency of Cu(II) by biochars. Raising the initial pH of the effluent enhanced the removal of Cu(II) from it. The optimum pyrolysis temperature was 400 degrees C for producing biochar from crop straws for acidic wastewater treatment, and the optimum reaction time was 8 hr.

Life-Cycle Analysis of Greenhouse Gas Emissions and Water Consumption – Effects of Coal and Biomass Conversion to Liquid Fuels as Analyzed with the GREET Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Qianfeng; Cai, Hao; Han, Jeongwoo

The vast reserves of coal in the U.S. provide a significant incentive for the development of processes for coal conversion to liquid fuels (CTL). Also, CTL using domestic coal can help move the U.S. toward greater energy independence and security. However, current conversion technologies are less economically competitive and generate greater greenhouse gas (GHG) emissions than production of petroleum fuels. Altex Technologies Corporation (Altex, hereinafter) and Pennsylvania State University have developed a hybrid technology to produce jet fuel from a feedstock blend of coal and biomass. Collaborating with Altex, Argonne National Laboratory has expanded and used the Greenhouse gases, Regulatedmore » Emissions, and Energy use in Transportation (GREET®) model to assess the life-cycle GHG emissions and water consumption of this hybrid technology. Biomass feedstocks include corn stover, switchgrass, and wheat straw. The option of biomass densification (bales to pellets) is also evaluated in this study. The results show that the densification process generates additional GHG emissions as a result of additional biomass process energy demand. This process coproduces a large amount of char, and this study investigates two scenarios to treat char: landfill disposal (Char-LF) and combustion for combined heat and power (CHP). Since the CHP scenarios export excess heat and electricity as coproducts, two coproduct handling methods are used for well-to-wake (WTWa) analysis: displacement (Char-CHP-Disp) and energy allocation (Char-CHP-EnAllo). When the feedstock contains 15 wt% densified wheat straw and 85 wt% lignite coal, WTWa GHG emissions of the coal-and-biomass-to-liquid pathways are 116, 97, and 137 gCO2e per megajoule (MJ) under the Char-LF, Char-CHP-Disp, and Char-CHP-EnAllo scenarios, respectively, as compared to conventional jet fuel production at 84 gCO2e/MJ. WTWa water consumption values are 0.072, -0.046, and 0.044 gal/MJ for Char-LF, Char-CHP-Disp, and Char-CHP-EnAllo, respectively, as compared to conventional jet fuel production at 0.028 gal/MJ. To reach the break-even point of 84 gCO2e/MJ, under the assumptions of constant product yields and energy demands regardless of the share of biomass and coal feedstocks, 31 wt%, 23 wt%, and 53 wt% of the feedstock blend need to be biomass under the Char-LF, Char-CHP-Disp, and Char-CHP-EnAllo scenarios, respectively.« less

Impact of ancient charcoal kilns on chemical properties of several forest soils after 2 centuries

NASA Astrophysics Data System (ADS)

Dufey, Joseph; Hardy, Brieuc; Cornelis, Jean-Thomas

2014-05-01

Pyrogenic carbon plays a major role in soil biogeochemical processes and carbon budgets. Until the early 19th century, charcoal was the unique combustible used for iron metallurgy in Wallonia (Belgium). Traditional charcoal kilns were built directly in the forest: wood logs were piled into a mound and isolated from air oxygen with a covering of vegetation residues and soil before setting fire, inducing wood pyrolysis. Nowadays, ancient wood-charring platforms are still easy to identify on the forest floor as heightened domes of 10 meters in diameter characterized by a very dark topsoil horizon containing charcoal dust and fragments. Our goal is to assess the effects of wood charring at mound kiln sites on the properties of various forest soil types in Wallonia (Belgium), after two centuries. We sampled soil by horizon in 18 ancient kiln sites to 1.20 meter depth. The adjacent charcoal-unaffected soils were sampled the same way. We also collected recent charcoal fragments and topsoil samples from a still active charcoal kiln located close to Dole (France) to apprehend the evolution of soil properties over time. The pH, total carbon (C) and nitrogen (N) content, available phosphorus (Pav), cation exchange capacity at pH 7 (CEC), exchangeable cations (Ca++, Mg++, K+, Na+) and loss on ignition at 550°C (LI550) were measured on each soil sample. We separated the soil profiles in 5 groups based on the nature of soil substrate and pedogenesis for interpretation of the results. We show that the total carbon stock is significantly increased at kiln sites due to higher C concentrations and greater depth of the organo-mineral horizon. The C/N ratio in charcoal-enriched soil horizons is significantly higher than in the neighboring reference soils but clearly attenuated compared to pure wood-charcoal fragments. The CEC is higher in the charcoal-enriched soil horizons, not only due to higher C concentrations but also to increased CEC by carbon unit at kiln sites. The high negative charge of charcoal results from surface oxidation processes over time. This charge varies over quite a wide range of values according to soil type, which might be explained by the nature of the charred wood. The surface soil horizons at kiln site show a completely desaturated exchange complex, comparable to the reference soils. However, the raise of the base saturation in the underlying horizons reflects the past liming effect of ashes produced by wood charring that has been completely erased from the topsoil in 200 years. Exchangeable K+ in the topsoil layers of kiln sites is very low, which can be related to an enhanced selectivity for Mg++ and Ca++ on the exchange complex of old charred material. Similarly, very little Pav is extracted from charcoal-enriched horizons, suggesting that Pav is either reduced in quantity or in availability. Our data clearly highlight the long-term effect of the accumulation of charred material on the evolution of soil chemical properties due to charcoal ageing and nutrient leaching.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calo, J.M.; Suuberg, E.M.; Hradil, G.

This project is concerned with the study of the nature and behavior of ''active sites'' in char gasification. The research strategy involves use of model chars produced from the phenol-formaldehyde family of resins. These materials have been chosen since they have structural features similar to those in coals, but are much ''cleaner'' in that the concentration of potentially catalytic impurities can be maintained at low levels. It should be borne in mind that the objective of this work is to study non-catalytic gasification processes. In the previous quarterly report, we presented evidence that low temperature oxygen chemisorption does not providemore » a site-specific titration of active sites in chars; the uptake of oxygen by a cleaned char surface was unquestionably shown to be a function of temperature and oxygen partial pressure, and the importance of these variables differs from char to char. The fact that ''active surface area'' (ASA) determined by various arbitrary methods does seem to generally correlate with reactivity, seems to suggest that reactivities under various gasification and chemisorption conditions are correlated but that mechanisitic inferences cannot necessarily be drawn from such data. In the present report, we have extended the study of low temperature oxidation of chars, considering mass loss as well as oxygen uptake, since the two processes are essentially inseparable under a wide range of conditions. This work represents more than a simple attempt at trying to learn more about the oxygen chemisorption technique; rather it offers the opportunity to study the mechanism of oxygen attack on char under conditions that allow for better understanding of the fundamental processes. For these reasons, this work was performed in the pyrogasifier reactor (developed for CO/sub 2/ gasification reactivity studies), and complements the ongoing work in the TGA apparatus. 6 refs., 9 figs., 1 tab.« less

Characterization of red mud-epoxy intumescent char using surface imaging and micro analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arogundade, A. I., E-mail: ajiunolorioba@gmail.com; Megat-Yusoff, P. S. M., E-mail: puteris@petronas.com.my; Faiz, A.

In this study, red mud (RM), an oxide waste was proposed as reinforcing, synergistic filler for the traditional epoxy intumescent coating (IC). 5.5 wt% of acid-modified and unmodified red mud were introduced into the basic intumescent formulation of ammonium polyphosphate (APP), pentaerythritol (PER) and melamine (MEL). In order to predict effect of modification on its suitability, Field emission electron scanning microscopy and Fourier transform infra red were used to obtain detailed characteristics such as the cell size, pore distribution, homogeneity and chemical composition of the red mud-epoxy carbonaceous char. Both acid-modified and unmodified RM-filled ICs produced chars with smaller andmore » more closely packed cells compared to chars from the unfilled coating. Both coating types had hard carbonaceous metal phosphate coverings that could act as heat barriers. The unmodified red mud was found to be antagonistic to the intumescent action with an expansion of only 2 times the initial thickness. The leached, low iron-red mud produced an expansion of 15 times the initial thickness, but possessed a hollow interior. From these findings, it may be deduced that while acid leaching of red mud may improve intumescent expansion, it would be necessary to optimize the percent filler loading to improve residual mass.« less

Investigation of growth responses in saprophytic fungi to charred biomass.

PubMed

Ascough, Philippa L; Sturrock, Craig J; Bird, Michael I

2010-03-01

We present the results of a study testing the response of two saprophytic white-rot fungi species, Pleurotus pulmonarius and Coriolus versicolor, to charred biomass (charcoal) as a growth substrate. We used a combination of optical microscopy, scanning electron microscopy, elemental abundance measurements, and isotope ratio mass spectrometry ((13)C and (15)N) to investigate fungal colonisation of control and incubated samples of Scots Pine (Pinus sylvestris) wood, and charcoal from the same species produced at 300 degrees C and 400 degrees C. Both species of fungi colonise the surface and interior of wood and charcoals over time periods of less than 70 days; however, distinctly different growth forms are evident between the exterior and interior of the charcoal substrate, with hyphal penetration concentrated along lines of structural weakness. Although the fungi were able to degrade and metabolise the pine wood, charcoal does not form a readily available source of fungal nutrients at least for these species under the conditions used in this study.

Quantity and quality of black carbon molecular markers as obtained by two chromatographic methods (GC-FID and HPLC-DAD) - How do results compare?

NASA Astrophysics Data System (ADS)

Schneider, M. P. W.; Smittenberg, R. H.; Dittmar, T.; Schmidt, M. W. I.

2009-04-01

Chars produced by wildfires are an important source of black carbon (BC) in the environment. After their deposition on the soil surface they can be distributed into rivers, marine waters and sediments. The analysis of benzenepolycarboxylic acids (BPCAs) as a quantitative measure for black carbon (BC) in soil and sediment samples is a well-established method (Glaser et al., 1998; Brodowski et al., 2005). Briefly, the nitric acid oxidation of fused aromatic ring systems in BC forms eight molecular markers (BPCAs), which can be assigned to BC, and which subsequently can be quantified by GC-FID (gas chromatography with flame ionization detector). Recently, this method was modified for the quantification of BC in seawater samples using HPLC-DAD (High performance liquid chromatography with diode array detector) for the determination of individual BPCAs (Dittmar, 2008). A direct comparison of both analytical techniques is lacking but would be important for future data comparison aimed at the calculation of global BC budgets. Here we present a systematic comparison of the two BPCA quantification methods. We prepared chars under well-defined laboratory conditions. In order to cover a broad spectrum of char properties we used two sources of biomass and a wide range of pyrolysis temperatures. Chestnut hardwood chips (Castanea sativa) and rice straw (Oryza sativa) were pyrolysed at temperatures between 200 and 1000°C under a constant N2 stream. The maximum temperatures were held constant for 5 hours (Hammes et al., 2006). The BC contents of the chars have been analysed using the BPCA extraction method followed by either GC-FID or HPLC-DAD quantification. Preliminary results suggest that both methods yield similar total quantities of BPCA, and also the proportions of the individual markers are similar. Ongoing experiments will allow for a more detailed comparison of the two methods. The BPCA composition of chars formed at different temperatures and from different precursor biomass is being used for this purpose. We seek to establish a conversion factor between both methods, if required. Results show that both the GC and the HPLC method can be used for organic samples containing some silica, such as grass char. Further tests include silica-rich materials, such as soils. Ongoing methodological work aims at carbon isotope analysis (13C and 14C) on individual BPCAs isolated via HPLC. At present the HPLC method employs tetrabutyl ammonium bromide (TBAB) as a modifier for the liquid phase. TBAB is not volatile and contains carbon, it therefore prevents carbon isotopic analysis on isolated BPCAs. References Brodowski, S., Rodionov, A., Haumeier, L., Glaser, B., Amelung, W. (2005) Revised black carbon assessment using benzene polycarboxylic acids. Organic Geochemistry, 36(9), 1299-1310. Dittmar, T. (2008) The molecular level determination of black carbon in marine dissolved organic matter. Organic Geochemistry, 39(4). 396-407. Glaser, B., Haumeier, L., Guggenberger, G., Zech, W. (1998) Black carbon in soils: the use of benzenecarboxylic acids as specific markers. Organic Geochemistry, 29(4), 811-819. Hammes, K. Smernik, R. J., Skjemstad, J. O., Herzog, A., Vogt, U. F., Schmidt, M. W. I. (2006) Synthesis and characterisation of laboratory-charred grass straw (Oryza saliva) and chestnut wood (Castanea sativa) as reference materials for black carbon quantification Organic Geochemistry 37(11). 1629-1633

Coal Technology Program progress report for April 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

In the Hydrocarbonization Research program, two successful experiments were completed in the bench-scale hydrocarbonizer. A settling test at a lower temperature (390/sup 0/F) using 20 percent toluene in Solvent Refined Coal (SRC) Unfiltered Oil (UFO) produced a 30 percent clarified product in 2 hr. Characterization tests include distillation curves for Wilsonville's SRC-UFO and a particle size distribution of Pittsburg and Midway Coal Mining Company's (PAMCO) SRC-UFO. Studies of intermediate-temperature pyrolysis of large blocks have been maintained with char samples continuing to demonstrate pyrophoricity, even after heating to 700/sup 0/C. Simulated distillation analysis of tars produced by the last eight experimentsmore » are being compared with those performed at Laramie upon tars produced by the Hanna No. 2 experiment. In Coal-Fueled MIUS, stainless steel tubing to be used in one of the furnace tube bundles was ordered and the bid package for the furnace completed. Tests continued on the coal feed system and with the cold flow fluidized bed model. For the Synthoil process, flow diagrams, material balances, and utilities requirements were completed for the entire facility. For the Hydrocarbonization process, flowsheets were reviewed for compatibility; equipment lists were brought up to date; and utilities requirements were compiled from the individual flowsheets. The char recovery and storage subsystem flowsheet was completed. (auth)« less

Removal of copper by oxygenated pyrolytic tire char: kinetics and mechanistic insights.

PubMed

Quek, Augustine; Balasubramanian, Rajashekhar

2011-04-01

The kinetics of copper ion (Cu(II)) removal from aqueous solution by pyrolytic tire char was modeled using five different conventional models. A modification to these models was also developed through a modified equation that accounts for precipitation. Conventional first- and second-order reaction models did not fit the copper sorption kinetics well, indicating a lack of simple rate-order dependency on solute concentration. Instead, a reversible first-order rate reaction showed the best fit to the data, indicating a dependence on surface functional groups. Due to the varying solution pH during the sorption process, modified external and internal mass transfer models were employed. Results showed that the sorption of copper onto oxygenated chars was limited by external mass transfer and internal resistance with and without the modification. However, the modification of the sorption process produced very different results for unoxygenated chars, which showed neither internal nor external limitation to sorption. Instead, its slow sorption rate indicates a lack of surface functional groups. The sorption of Cu(II) by oxygenated and unoxygenated chars was also found to occur via three and two distinct stages, respectively. Copyright © 2010 Elsevier Inc. All rights reserved.

Effects of temperature, pressure, and carrier gas on the cracking of coal tar over a char-dolomite mixtures and calcined dolomite in a fixed-bed reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seshadri, K.; Shamsi, A.

1998-10-01

A distillation fraction of a coal-derived liquid (tar) was cracked over a char-dolomite mixture, calcined dolomite, and silicon carbide in a fixed-bed reactor. The char-dolomite mixture (FWC) was produced from Pittsburgh No. 8 coal and dolomite in a Foster Wheeler carbonizer. The experiments were conducted under nitrogen and simulated coal gas (SCG), which was a mixture of CO, CO{sub 2}, H{sub 2}S, CH{sub 4}, N{sub 2}, and steam, at 1 and 17 atm. The conversion over these materials under nitrogen was much higher at 17 atm than at 1 atm. At higher pressures, tar molecules were trapped in the poresmore » of the bed material and underwent secondary reactions, resulting in the formation of excess char. However, when nitrogen was replaced by SCG, the reactions that induce char formation were suppressed, thus increasing the yield of gaseous products. The analysis of the gaseous products and the spent bed materials for organic and inorganic carbons suggested that the product distribution can be altered by changing the carrier gas, temperature, and pressure.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suuberg, E.M.; Lilly, W.D.; Aarna, I.

This project is concerned with the mechanism of reduction of both NO and N{sub 2}O by carbons. It was recognized some years ago that NO formed during fluidized bed coal combustion can be heterogeneously reduced in-situ by the carbonaceous solid intermediates of combustion. This has been recently supplemented by the knowledge that heterogeneous reaction with carbon can also play an important role in reducing emissions of N{sub 2}, but that the NO-carbon reactions might also contribute to formation of N{sub 2}. The precise role of carbon in N{sub 2} reduction and formation has yet to be established. Interest in themore » N{sub 2} and N{sub 2}O-char reactions has been significant in connection with both combustor modeling, as well as in design of post-combustion NO{sub x} control strategies. In our studies, a DuPont thermogravimetric analyzer (TGA) is used for the char reactivity studies. The temperature and mass are recorded as function of time, using a Macintosh computer and software for simultaneous apparatus control and data acquisition. Specific surface areas of char samples were determined by the N{sub 2} BET method at 77 K. A standard flow-type adsorption device (Quantasorb) was used for the measurements. Prior to surface area analysis, all samples were outgassed in a flow of nitrogen at 573 K for 3 hours. The carbonaceous solids used were resin char, graphite, coconut char and a Wyodak coal char. As was noted in the last report, carbons derived from different original materials show quite similar behaviors, in terms of the trends, but there are significant differences in actual reaction rates. It was shown that the spread of the reaction rate data from different studies, when expressed on a mass of carbon reactant- or surface area-basis, was almost the same.« less

Analysis of Flame Retardancy in Polymer Blends by Synchrotron X-ray K-edge Tomography and Interferometric Phase Contrast Movies.

PubMed

Olatinwo, Mutairu B; Ham, Kyungmin; McCarney, Jonathan; Marathe, Shashidhara; Ge, Jinghua; Knapp, Gerry; Butler, Leslie G

2016-03-10

Underwriters Laboratories 94 test bars have been imaged with X-ray K-edge tomography between 12 and 32 keV to assess the bromine and antimony concentration gradient across char layers of partially burnt samples. Phase contrast tomography on partially burnt samples showed gas bubbles and dark-field scattering ascribed to residual blend inhomogeneity. In addition, single-shot grating interferometry was used to record X-ray movies of test samples during heating (IR and flame) intended to mimic the UL 94 plastics flammability test. The UL 94 test bars were formulated with varying concentrations of a brominated flame retardant, Saytex 8010, and a synergist, Sb2O3, blended into high-impact polystyrene (HIPS). Depending on the sample composition, samples will pass or fail the UL 94 plastics flammability test. Tomography and interferometry imaging show differences that correlate with UL 94 performance. Key features such as char layer, gas bubble formation, microcracks, and dissolution of the flame retardant in the char layer regions are used in understanding the efficiency of the flame retardant and synergist. The samples that pass the UL 94 test have a thick, highly visible char layer as well as an interior rich in gas bubbles. Growth of gas bubbles from flame-retardant thermal decomposition is noted in the X-ray phase contrast movies. Also noteworthy is an absence of bubbles near the burning surface of the polymer; dark-field images after burning suggest a microcrack structure between interior bubbles and the surface. The accepted mechanism for flame retardant activity includes free radical quenching in the flame by bromine and antimony species. The imaging supports this as well as provides a fast inspection of other parameters, such as viscosity and surface tension.

Intercomparison of thermal-optical method with different temperature protocols: Implications from source samples and solvent extraction

NASA Astrophysics Data System (ADS)

Cheng, Yuan; Duan, Feng-kui; He, Ke-bin; Du, Zhen-yu; Zheng, Mei; Ma, Yong-liang

2012-12-01

Three temperature protocols with different peak inert mode temperature (Tpeak-inert) were compared based on source and ambient samples (both untreated and extracted using a mixture of hexane, methylene chloride, and acetone) collected in Beijing, China. The ratio of EC580 (elemental carbon measured by the protocol with a Tpeak-inert of 580 °C; similar hereinafter) to EC850 could be as high as 4.8 for biomass smoke samples whereas the ratio was about 1.0 for diesel and gasoline exhaust samples. The EC580 to EC850 ratio averaged 1.95 ± 0.89 and 1.13 ± 0.20 for the untreated and extracted ambient samples, whereas the EC580 to EC650 ratio of ambient samples was 1.22 ± 0.10 and 1.20 ± 0.12 before and after extraction. It was suggested that there are two competing mechanisms for the effects of Tpeak-inert on the EC results such that when Tpeak-inert is increased, one mechanism tends to decrease EC by increasing the amount of charring whereas the other tends to increase EC through promoting more charring to evolve before native EC. Results from this study showed that EC does not always decrease when increasing the peak inert mode temperature. Moreover, reducing the charring amount could improve the protocols agreement on EC measurements, whereas temperature protocol would not influence the EC results if no charring is formed. This study also demonstrated the benefits of allowing for the OC and EC split occurring in the inert mode when a high Tpeak-inert is used (e.g., 850 °C).

Differences in gasification behaviors and related properties between entrained gasifier fly ash and coal char

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jing Gu; Shiyong Wu; Youqing Wu

2008-11-15

In the study, two fly ash samples from Texaco gasifiers were compared to coal char and the physical and chemical properties and reactivity of samples were investigated by scanning electron microscopy (SEM), SEM-energy-dispersive spectrometry (EDS), X-ray diffraction (XRD), N{sub 2} and CO{sub 2} adsorption method, and isothermal thermogravimetric analysis. The main results were obtained. The carbon content of gasified fly ashes exhibited 31-37%, which was less than the carbon content of 58-59% in the feed coal. The fly ashes exhibited higher Brunauer-Emmett-Teller (BET) surface area, richer meso- and micropores, more disordered carbon crystalline structure, and better CO{sub 2} gasification reactivitymore » than coal char. Ashes in fly ashes occurred to agglomerate into larger spherical grains, while those in coal char do not agglomerate. The minerals in fly ashes, especial alkali and alkaline-earth metals, had a catalytic effect on gasification reactivity of fly ash carbon. In the low-temperature range, the gasification process of fly ashes is mainly in chemical control, while in the high-temperature range, it is mainly in gas diffusion control, which was similar to coal char. In addition, the carbon in fly ashes was partially gasified and activated by water vapor and exhibited higher BET surface area and better gasification activity. Consequently, the fact that these carbons in fly ashes from entrained flow gasifiers are reclaimed and reused will be considered to be feasible. 15 refs., 7 figs., 5 tabs.« less

Fire resistance properties of ceramic wool fiber reinforced intumescent coatings

NASA Astrophysics Data System (ADS)

Amir, N.; Othman, W. M. S. W.; Ahmad, F.

2015-07-01

This research studied the effects of varied weight percentage and length of ceramic wool fiber (CWF) reinforcement to fire retardant performance of epoxy-based intumescent coating. Ten formulations were developed using ammonium polyphosphate (APP), expandable graphite (EG), melamine (MEL) and boric acid (BA). The mixing was conducted in two stages; powdered materials were grinded in Rocklabs mortar grinder and epoxy-mixed using Caframo mixer at low speed mixing. The samples were applied on mild steel substrate and exposed to 500°C heat inside Carbolite electric furnace. The char expansion and its physical properties were observed. Scanning electron microscopy (SEM) analyses were conducted to inspect the fiber dispersion, fiber condition and the cell structure of both coatings and chars produced. Thermogravimetric analyses (TGA) were conducted to study the thermal properties of the coating such as degradation temperature and residual weight. Fire retardant performance was determined by measuring backside temperature of substrate in 1-hour, 1000°C Bunsen burner test according to UL 1709 fire regime. The results showed that intumescent coating reinforced with CWF produced better fire resistance performance. When compared to unreinforced coating, formulation S6-15 significantly reduced steel temperature at approximately 34.7% to around 175°C. However, higher fiber weight percentage had slightly decreased fire retardant performance of the coating.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amir, N., E-mail: norlailiamir@petronas.com.my; Othman, W. M. S. W., E-mail: wamosa@gmail.com; Ahmad, F., E-mail: faizahmad@petronas.com.my

This research studied the effects of varied weight percentage and length of ceramic wool fiber (CWF) reinforcement to fire retardant performance of epoxy-based intumescent coating. Ten formulations were developed using ammonium polyphosphate (APP), expandable graphite (EG), melamine (MEL) and boric acid (BA). The mixing was conducted in two stages; powdered materials were grinded in Rocklabs mortar grinder and epoxy-mixed using Caframo mixer at low speed mixing. The samples were applied on mild steel substrate and exposed to 500°C heat inside Carbolite electric furnace. The char expansion and its physical properties were observed. Scanning electron microscopy (SEM) analyses were conducted tomore » inspect the fiber dispersion, fiber condition and the cell structure of both coatings and chars produced. Thermogravimetric analyses (TGA) were conducted to study the thermal properties of the coating such as degradation temperature and residual weight. Fire retardant performance was determined by measuring backside temperature of substrate in 1-hour, 1000°C Bunsen burner test according to UL 1709 fire regime. The results showed that intumescent coating reinforced with CWF produced better fire resistance performance. When compared to unreinforced coating, formulation S6-15 significantly reduced steel temperature at approximately 34.7% to around 175°C. However, higher fiber weight percentage had slightly decreased fire retardant performance of the coating.« less

Understanding how lake populations of arctic char are structured and function with special consideration of the potential effects of climate change: a multi-faceted approach.

PubMed

Budy, Phaedra; Luecke, Chris

2014-09-01

Size dimorphism in fish populations, both its causes and consequences, has been an area of considerable focus; however, uncertainty remains whether size dimorphism is dynamic or stabilizing and about the role of exogenous factors. Here, we explored patterns among empirical vital rates, population structure, abundance and trend, and predicted the effects of climate change on populations of arctic char (Salvelinus alpinus) in two lakes. Both populations cycle dramatically between dominance by small (≤300 mm) and large (>300 mm) char. Apparent survival (Φ) and specific growth rates (SGR) were relatively high (40-96%; SGR range 0.03-1.5%) and comparable to those of conspecifics at lower latitudes. Climate change scenarios mimicked observed patterns of warming and resulted in temperatures closer to optimal for char growth (15.15 °C) and a longer growing season. An increase in consumption rates (28-34%) under climate change scenarios led to much greater growth rates (23-34%). Higher growth rates predicted under climate change resulted in an even greater predicted amplitude of cycles in population structure as well as an increase in reproductive output (Ro) and decrease in generation time (Go). Collectively, these results indicate arctic char populations (not just individuals) are extremely sensitive to small changes in the number of ice-free days. We hypothesize years with a longer growing season, predicted to occur more often under climate change, produce elevated growth rates of small char and act in a manner similar to a "resource pulse," allowing a sub-set of small char to "break through," thus setting the cycle in population structure.

Understanding how lake populations of arctic char are structured and function with special consideration of the potential effects of climate change: A multi-faceted approach.

USGS Publications Warehouse

Budy, Phaedra; Luecke, Chris

2014-01-01

Size dimorphism in fish populations, both its causes and consequences, has been an area of considerable focus; however, uncertainty remains whether size dimorphism is dynamic or stabilizing and about the role of exogenous factors. Here, we explored patterns among empirical vital rates, population structure, abundance and trend, and predicted the effects of climate change on populations of arctic char (Salvelinus alpinus) in two lakes. Both populations cycle dramatically between dominance by small (≤300 mm) and large (>300 mm) char. Apparent survival (Φ) and specific growth rates (SGR) were relatively high (40–96 %; SGR range 0.03–1.5 %) and comparable to those of conspecifics at lower latitudes. Climate change scenarios mimicked observed patterns of warming and resulted in temperatures closer to optimal for char growth (15.15 °C) and a longer growing season. An increase in consumption rates (28–34 %) under climate change scenarios led to much greater growth rates (23–34 %). Higher growth rates predicted under climate change resulted in an even greater predicted amplitude of cycles in population structure as well as an increase in reproductive output (Ro) and decrease in generation time (Go). Collectively, these results indicate arctic char populations (not just individuals) are extremely sensitive to small changes in the number of ice-free days. We hypothesize years with a longer growing season, predicted to occur more often under climate change, produce elevated growth rates of small char and act in a manner similar to a “resource pulse,” allowing a sub-set of small char to “break through,” thus setting the cycle in population structure.

Recovery of solid fuel from municipal solid waste by hydrothermal treatment using subcritical water.

PubMed

Hwang, In-Hee; Aoyama, Hiroya; Matsuto, Toshihiko; Nakagishi, Tatsuhiro; Matsuo, Takayuki

2012-03-01

Hydrothermal treatments using subcritical water (HTSW) such as that at 234°C and 3MPa (LT condition) and 295°C and 8MPa (HT condition) were investigated to recover solid fuel from municipal solid waste (MSW). Printing paper, dog food (DF), wooden chopsticks, and mixed plastic film and sheets of polyethylene, polypropylene, and polystyrene were prepared as model MSW components, in which polyvinylchloride (PVC) powder and sodium chloride were used to simulate Cl sources. While more than 75% of carbon in paper, DF, and wood was recovered as char under both LT and HT conditions, plastics did not degrade under either LT or HT conditions. The heating value (HV) of obtained char was 13,886-27,544 kJ/kg and was comparable to that of brown coal and lignite. Higher formation of fixed carbon and greater oxygen dissociation during HTSW were thought to improve the HV of char. Cl atoms added as PVC powder and sodium chloride to raw material remained in char after HTSW. However, most Cl originating from PVC was found to converse into soluble Cl compounds during HTSW under the HT condition and could be removed by washing. From these results, the merit of HTSW as a method of recovering solid fuel from MSW is considered to produce char with minimal carbon loss without a drying process prior to HTSW. In addition, Cl originating from PVC decomposes into soluble Cl compound under the HT condition. The combination of HTSW under the HT condition and char washing might improve the quality of char as alternative fuel. Copyright © 2011 Elsevier Ltd. All rights reserved.

Synergistic Effect of Co-utilization of Coal and Biomass Char: An Overview

NASA Astrophysics Data System (ADS)

Paiman, M. E. S.; Hamzah, N. S.; Idris, S. S.; Rahman, N. A.; Ismail, K.

2018-05-01

Global concerns on impact of greenhouse gases emission, mostly released from coal-fired power plant, and the depletion of fossil fuel particularly coal, has led the production of electricity from alternatives resources such as co-utilization technologies. Previous studies proved that the co-utilization of coal and biomass/biomass chars has significantly reduced the emission of greenhouse gases either during the pyrolysis, combustion or gasification process in laboratories, pilots as well as in the industrial scales. Interestingly, most of the studies reported the presence of synergistic effect during the co-utilization processes particularly between coal and biomass char while some are not. Biomass chars were found to have porous and highly disorder carbon structure and belong to the class of most reactive carbon material, resulting to be more reactive than those hard coal and lignite. Up to date, microwave assisted pyrolysis is one of the best and latest techniques employed to produce better quality of biomass chars and it is also reduce the processing cost. Lot of works has been done regarding on the existence of synergistic effects during its co-utilization. However, the knowledge is limited to thermal and product characteristics so far. Even so, the specific reasons behind its existence are yet to understand well. Therefore, in this paper, the emphasis will be given on the synergistic effects on emission characteristics of co-utilization of coal and biomass chars so that it can be apply in energy-based industries to help in reduction of the greenhouse gases emission.

Modeling and evaluation of chromium remediation from water using low cost bio-char, a green adsorbent.

PubMed

Mohan, Dinesh; Rajput, Shalini; Singh, Vinod K; Steele, Philip H; Pittman, Charles U

2011-04-15

Oak wood and oak bark chars were obtained from fast pyrolysis in an auger reactor at 400-450 °C. These chars were characterized and utilized for Cr(VI) remediation from water. Batch sorption studies were performed at different temperatures, pH values and solid to liquid ratios. Maximum chromium was removed at pH 2.0. A kinetic study yielded an optimum equilibrium time of 48 h with an adsorbent dose of 10 g/L. Sorption studies were conducted over a concentration range of 1-100mg/L. Cr(VI) removal increased with an increase in temperature (Q(Oak wood)(°): 25 °C = 3.03 mg/g; 35 °C = 4.08 mg/g; 45 °C = 4.93 mg/g and Q(Oakbark)(°): 25 °C = 4.62 mg/g; 35 °C = 7.43 mg/g; 45 °C = 7.51 mg/g). More chromium was removed with oak bark than oak wood. The char performances were evaluated using the Freundlich, Langmuir, Redlich-Peterson, Toth, Radke and Sips adsorption isotherm models. The Sips adsorption isotherm model best fits the experimental data [high regression (R(2)) coefficients]. The overall kinetic data was satisfactorily explained by a pseudo second order rate expression. Water penetrated into the char walls exposing Cr(VI) to additional adsorption sites that were not on the surfaces of dry char pores. It is remarkable that oak chars (S(BET): 1-3m(2)g(-1)) can remove similar amounts of Cr(VI) as activated carbon (S(BET): ∼ 1000 m(2)g(-1)). Thus, byproduct chars from bio-oil production might be used as inexpensive adsorbents for water purification. Char samples were successfully used for chromium remediation from contaminated surface water with dissolved interfering ions. Copyright © 2011 Elsevier B.V. All rights reserved.

Thermochemical characterization of pigeon pea stalk for its efficient utilization as an energy source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katyal, S.K.; Iyer, P.V.R.

2000-05-01

Pigeon pea stalk is a widely available biomass species in India. In this article the potential use of pigeon pea stalk as a fuel source through thermochemical conversion methods such as combustion, gasification, and pyrolysis has been investigated through experimentation using a thermogravimetric analyzer and pilot-plant-scale equipment. It has been proposed that pigeon pea stalks can be effectively utilized in two ways. The first is to pyrolyze the material to produce value-added products such as char, tar, and fuel gas. The second alternative is to partially pyrolyze the material to remove tar-forming volatiles, followed by gasification of reactive char tomore » generate producer gas.« less

Recovery of solid fuel from municipal solid waste by hydrothermal treatment using subcritical water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, In-Hee, E-mail: hwang@eng.hokudai.ac.jp; Aoyama, Hiroya; Matsuto, Toshihiko

2012-03-15

Highlights: Black-Right-Pointing-Pointer Hydrothermal treatment using subcritical water was studied to recover solid fuel from MSW. Black-Right-Pointing-Pointer More than 75% of carbon in MSW was recovered as char. Black-Right-Pointing-Pointer Heating value of char was comparable to that of brown coal and lignite. Black-Right-Pointing-Pointer Polyvinyl chloride was decomposed at 295 Degree-Sign C and 8 MPa and was removed by washing. - Abstract: Hydrothermal treatments using subcritical water (HTSW) such as that at 234 Degree-Sign C and 3 MPa (LT condition) and 295 Degree-Sign C and 8 MPa (HT condition) were investigated to recover solid fuel from municipal solid waste (MSW). Printing paper,more » dog food (DF), wooden chopsticks, and mixed plastic film and sheets of polyethylene, polypropylene, and polystyrene were prepared as model MSW components, in which polyvinylchloride (PVC) powder and sodium chloride were used to simulate Cl sources. While more than 75% of carbon in paper, DF, and wood was recovered as char under both LT and HT conditions, plastics did not degrade under either LT or HT conditions. The heating value (HV) of obtained char was 13,886-27,544 kJ/kg and was comparable to that of brown coal and lignite. Higher formation of fixed carbon and greater oxygen dissociation during HTSW were thought to improve the HV of char. Cl atoms added as PVC powder and sodium chloride to raw material remained in char after HTSW. However, most Cl originating from PVC was found to converse into soluble Cl compounds during HTSW under the HT condition and could be removed by washing. From these results, the merit of HTSW as a method of recovering solid fuel from MSW is considered to produce char with minimal carbon loss without a drying process prior to HTSW. In addition, Cl originating from PVC decomposes into soluble Cl compound under the HT condition. The combination of HTSW under the HT condition and char washing might improve the quality of char as alternative fuel.« less

Solidifying process and flame retardancy of epoxy resin cured with boron-containing phenolic resin

NASA Astrophysics Data System (ADS)

Deng, Peng; Shi, Yan; Liu, Yuansen; Liu, Yuan; Wang, Qi

2018-01-01

For the sake of improving the charring performance and flame retardancy of epoxy resin (EP), boron-containing phenolic resin (BPR) instead of a conventional curing agent, linear phenolic resin (LPR) was employed to cure EP. Of several possible chemical structures for BPR, the existence of benzyl hydroxy groups in BPR chains has been confirmed using 1H nuclear magnetic resonance spectroscopy. The resonance of these groups may reasonably explain the higher curing reactivity of BPR-cured EP than that of LPR-cured EP. Thermogravimetric analysis, observation of the morphologies of the char residues and X-ray photoelectron spectroscopic were performed to characterize the charring process. Due to the presence of B2O3 produced on the char surface from decomposition of phenyl borates and the facile high self-crosslinking reaction of BPR, a more continuous and stronger char barrier was formed for BPR-cured EP compared to that for the LPR-cured EP system. Therefore the former exhibited much better flame retardancy. In addition, BPR-cured EP also displayed better dynamic mechanical properties, than those observed for LPR-cured EP. It is not subject to the significant lowering the glass transition temperature of the polymer which accompanies curing with LPR. This suggests that BPR cured resin may meet the requirement for utilization at high temperature.

Graphite and ablative material response to CO2 laser, carbon-arc, and xenon-arc radiation

NASA Technical Reports Server (NTRS)

Brewer, W. D.

1976-01-01

The behavior was investigated of graphite and several charring ablators in a variety of high-radiative heat-flux environments. A commercial-grade graphite and nine state-of-the-art charring ablators were subjected to various radiative environments produced by a CO2 laser and a carbon arc. Graphite was also tested in xenon-arc radiation. Heat-flux levels ranged from 10 to 47 MW/sq m. Tests were conducted in air, nitrogen, helium, and a CO2-N2 mixture which simulated the Venus atmosphere. The experimental results were compared with theoretical results obtained with a one-dimensional charring-ablator analysis and a two-dimensional subliming-ablator analysis. Neither the graphite nor the charring ablators showed significant differences in appearance or microstructure after testing in the different radiative environments. The performance of phenolic nylon and graphite was predicted satisfactorily with existing analyses and published material property data. Good agreement between experimental and analytical results was obtained by using sublimation parameters from a chemical nonequilibrium analysis of graphite sublimation. Some charring ablators performed reasonably well and could withstand radiative fluxes of the level encountered in certain planetary entries. Other materials showed excessive surface recession and/or large amounts of cracking and spalling, and appear to be unsuitable for severe radiative environments.

Effects of pyrolysis conditions on yield of bio-chars from pine chips

Treesearch

Qiangu Yan; Hossein Toghiani; Fei Yu; Zhiyong Cai; Jilei Zhang

2011-01-01

The influences of temperature, heating rate, purge gas type, and flow rate on the yield of chars produced from pyrolyzing southern pine chips were investigated. Pyrolysis temperatures were between 450°C and 1,000°C, with heating rates of 0.5°C/min, 1.0°C/min, 10°C/min, 30°C/min, 50°C/min, and 100°C/min. Purge gases, nitrogen (N2), hydrogen (H

Perfluorinated alkyl substances (PFAS) in terrestrial environments in Greenland and Faroe Islands.

PubMed

Bossi, Rossana; Dam, Maria; Rigét, Frank F

2015-06-01

Perfluorinated alkylated substances (PFASs) have been measured in liver samples from terrestrial organisms from Greenland and the Faeroe Islands. Samples from ptarmigan (West Greenland), reindeer (southwest-Greenland), muskox (East Greenland), and land-locked Arctic char from southwest Greenland and the Faroe Islands were analyzed. In addition, PFASs levels in land-locked brown trout from Faroese lakes are reported. Of the 17 PFASs analyzed in the samples the following compounds were detected: PFOS, PFNA, PFDA, PFUnA, PFDoA, PFTrA, and PFTeA. PFNA was the compound detected in most samples and in all species. However, the compound detected at highest concentration was dependent on species, with overall highest concentrations of PFTrA and PFUnA being detected in trout liver from Lake á Mýranar (Faroe Islands). In muskox, the PFAS occurring at highest concentrations was PFDA, which was among the PFAS detected at lowest concentrations in freshwater fish, and was only detected in one individual ptarmigan. The concentration of PFOS, PFDoA and PFTrA in Arctic char from Greenland and Faroe Islands were similar, whereas the concentration of PFNA, PFDA and PFUnA were higher in Arctic char than those from Greenland. The opposite was observed for PFTeA. The PFASs occurring at highest concentrations in trout were PFTrA and PFUnA. Arctic char from Lake á Mýranar had much lower concentrations of PFTrA and PFUnA than in trout from the lakes analyzed, but a higher concentration of PFTeA than trout from the same lake. A clear pattern with odd-carbon number homologues concentrations higher than the next lower even homologue was observed in fish samples, which is consistent with the hypothesis of transport of volatile precursors to remote regions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Anadromous char as an alternate food choice to marine animals: a synthesis of Hg concentrations, population features and other influencing factors.

PubMed

Evans, Marlene S; Muir, Derek C G; Keating, Jonathan; Wang, Xiaowa

2015-03-15

This study was conducted to confirm sporadic measurements made over the late 1970s to the early 1990 s which determined that mercury (Hg) concentrations were low in anadromous char across Arctic and subarctic Canada including northern Québec and Labrador. Over 2004-2013, anadromous char populations across northern Canada were investigated at 20 sites for Hg concentrations and life history characteristics. Hg concentrations were extremely low in anadromous char muscle, typically <0.05 μg/g (wet weight) and, at each location, generally increased with fish length, age and nitrogen isotope (δ(15)N) ratio and decreased with condition factor and %lipid; correlations with carbon isotope (δ(13)C) ratio were inconsistent. Location and year were significant variables influencing Hg concentrations over the study area; longitude and latitude also were significant influencing variables. Char length, weight, age, condition factor and lipid content explained additional variance. A tendency towards higher Hg concentrations with increasing latitude may be partially related to decreasing growth of char towards the north. However, Hg concentrations in char were positively correlated with growth rates suggesting that Hg concentrations in char also were higher in the more productive study areas, including to the west where mainland riverine inputs of terrestrial carbon, nutrients, and Hg were greater. The data base for assessing time trends in char was limited by the small number of years investigated at most locations, variable fish size across years, small sample size, etc. Where temporal trends were detected, they were of increase on the long term (1970s, 1980s or early 1990 s to the present) but of decrease on the short term (early 2000s to present) with Nain (Labrador) showing the converse pattern. Higher Hg concentrations were also related to lower condition factor and cooler springs. Hg concentrations in anadromous char are compared with other terrestrial, aquatic and marine vertebrates in traditional diets. The known information on anadromous char is reviewed including population features, habitat, and harvests. Future Hg trend monitoring should focus on specific locations and harvest areas within these areas to better assess trends and influencing factors. Crown Copyright © 2014. Published by Elsevier B.V. All rights reserved.

Burning characteristics and fiber retention of graphite/resin matrix composites

NASA Technical Reports Server (NTRS)

Bowles, K. J.

1980-01-01

Graphite fiber reinforced resin matrix composites were subjected to controlled burning conditions to determine their burning characteristics and fiber retention properties. Small samples were burned with a natural gas fired torch to study the effects of fiber orientation and structural flaws such as holes and slits that were machined into the laminates. Larger laminate samples were burned in a modified heat release rate calorimeter. Unidirectional epoxy/graphite and polyimide/graphite composites and boron powder filled samples of each of the two composite systems were burn tested. The composites were exposed to a thermal radiation of 5.3 Btu/sq ft-sec in air. Samples of each of the unfilled composite were decomposed anaerobically in the calorimeter. Weight loss data were recorded for burning and decomposition times up to thirty-five minutes. The effects of fiber orientation, flaws, and boron filler additives to the resins were evaluated. A high char forming polyimide resin was no more effective in retaining graphite fibers than a low char forming epoxy resin when burned in air. Boron powder additions to both the polyimide and the epoxy resins stabilized the chars and effectively controlled the fiber release.

Studying the specific features pertinent to combustion of chars obtained from coals having different degrees of metamorphism and biomass chars

NASA Astrophysics Data System (ADS)

Bestsennyi, I. V.; Shchudlo, T. S.; Dunaevskaya, N. I.; Topal, A. I.

2013-12-01

Better conditions for igniting low-reaction coal (anthracite) can be obtained, higher fuel burnout ratio can be achieved, and the problem of shortage of a certain grade of coal can be solved by firing coal mixtures and by combusting coal jointly with solid biomass in coal-fired boilers. Results from studying the synergetic effect that had been revealed previously during the combustion of coal mixtures in flames are presented. A similar effect was also obtained during joint combustion of coal and wood in a flame. The kinetics pertinent to combustion of char mixtures obtained from coals characterized by different degrees of metamorphism and the kinetics pertinent to combustion of wood chars were studied on the RSK-1D laboratory setup. It was found from the experiments that the combustion rate of char mixtures obtained from coals having close degrees of metamorphism is equal to the value determined as a weighted mean rate with respect to the content of carbon. The combustion rate of char mixtures obtained from coals having essentially different degrees of metamorphism is close to the combustion rate of more reactive coal initially in the process and to the combustion rate of less reactive coal at the end of the process. A dependence of the specific burnout rate of carbon contained in the char of two wood fractions on reciprocal temperature in the range 663—833 K is obtained. The combustion mode of an experimental sample is determined together with the reaction rate constant and activation energy.

Evaluation of a Technology-Based Adaptive Learning and Prevention Program for Stress Response-A Randomized Controlled Trial.

PubMed

Wesemann, Ulrich; Kowalski, Jens T; Jacobsen, Thomas; Beudt, Susan; Jacobs, Herbert; Fehr, Julia; Büchler, Jana; Zimmermann, Peter L

2016-08-01

To prevent deployment-related disorders, Chaos Driven Situations Management Retrieval System (CHARLY), a computer-aided training platform with a biofeedback interface has been developed. It simulates critical situations photorealistic for certain target and occupational groups. CHARLY was evaluated as a 1.5 days predeployment training method comparing it with the routine training. The evaluation was carried out for a matched random sample of N = 67 soldiers deployed in Afghanistan (International Security Assistance Force). Data collection took place before and after the prevention program and 4 to 6 weeks after deployment, which included mental state, post-traumatic stress disorder (PTSD) symptoms, knowledge of and attitude toward PTSD, and deployment-specific stressors. CHARLY has been significantly superior to the control group in terms of psychoeducation and attitude change. As to the mental state, both groups showed a significant increase in stress after deployment with significant lower increase in CHARLY. For PTSD-specific symptoms, CHARLY achieved a significant superiority. The fact that PTSD-specific scales showed significant differences at the end of deployment substantiates the validity of a specifically preventive effect of CHARLY. The study results tentatively indicate that highly standardized, computer-based primary prevention of mental disorders in soldiers on deployment might be superior to other more personal and less standardized forms of prevention. Reprint & Copyright © 2016 Association of Military Surgeons of the U.S.

Biochar, Tool for Climate Change Mitigation and Soil Management

NASA Astrophysics Data System (ADS)

Shackley, Simon; Sohi, Saran; Ibarrola, Rodrigo; Hammond, Jim; Mašek, Ondřej; Brownsort, Peter; Cross, Andrew; Prendergast-Miller, Miranda; Haszeldine, Stuart

Biochar is the solid remains of any organic material that has been heated to at least 350oC in a zero-oxygen or oxygen-limited environment, which is intended to be mixed with soils. If the solid remains are not suitable for addition to soils, or will be burned as a fuel or used as an aggregate in construction, it is defined as char not biochar. There is a very wide range of potential biochar feedstocks, e.g., wood waste, timber, agricultural residues and wastes (straws, bagasse, manure, husks, shells, fibers, etc.), leaves, food wastes, paper and sewage sludge, green waste, distiller's grain, and many others. Pyrolysis is usually the technology of choice for producing biochar, though biomass gasification also produces smaller char yields. Syngas and pyrolytic bio-liquids, which have a potential use as energy carriers, are produced alongside biochar.

Production, Stocks and Characteristics of Wildfire Charcoal in Canadian Boreal Forests; a Preliminary Synthesis

NASA Astrophysics Data System (ADS)

Preston, C. M.; Simard, M.

2016-12-01

Crowning wildfires are a major driver of carbon stocks and ecosystem development in Canadian boreal forests, but there is insufficient information to incorporate pyrogenic carbon (PyC) into models and management strategies. Data comparison is challenging because of varied experimental design, and studies are often limited to forest floor; nonetheless we have attempted a synthesis limited to visually determined PyC, hereafter designated "charcoal". Sources include our study of amounts, depth distribution (forest floor plus variable amounts of upper mineral soil) and chemical properties of charcoal (>2 mm) from a fire chronosequence in the Abitibi region of Quebec (51 jack pine (Pinus banksiana) and black spruce (Picea mariana) sites, 24 to 2355 years since fire). Complete charcoal production of 7900 kg/ha (forest floor, down wood, standing stems) was determined from an experimental crownfire in jack pine near Fort Providence (NWT) in 2012. Published data were assembled mainly from boreal conifer studies, but using more disparate sources for production, plus laboratory charring studies. Typical findings include high spatial variability, with depth distributions often showing a maximum around the organic-mineral interface. Stocks varied widely (up to ca. 5500 kg/ha), with little initial discernable trend with time, but were much lower in the few older sites (>700y). Total C and N were widely scattered for younger samples, but older samples were mainly 500-600 g C/kg with C/N values around 100. Similarly, carbon-13 NMR spectra show wider variation in young samples, with the oldest samples being highly aromatic. These initial variations are consistent with field reports of highly variable temperatures and duration of charring and many laboratory studies. As a starting point, it may be possibly suggested that a boreal crowning wildfire might produce some 5000-10000 kg/ha of charred material of 550-650 g C/kg, with half to two-thirds on forest floor and down wood and most of the rest on standing stems. Our synthesis mainly highlights future research needs, including more measurements on stems and down wood and chemical analysis of the black carbon component of charcoal.

Etude de production et de caracterisation de biocharbons de panic erige (Panicum virgatum L.) obtenus par pyrolyse

NASA Astrophysics Data System (ADS)

Pilon, Guillaume

This research aimed at the production of biomass char under pyrolytic conditions, targeting biochar as soil amendment, while also considering its application as biocoal, either for bioenergy or subsequent upgrading. The production of biomass char was performed using two bench-scale, batch-type, fixed-bed reactors, each with an operating capacity of 1 and 25 gw.b. /batch, respectively. Switchgrass (Panicum virgatum) has been used for the tests. Production conditions studied implied temperatures of 300, 400 and 500 °C with short residence times (2.5 and 5 min). As well, the effect of using CO2 as vector gas has been compared to a common inert environment of N2. The effects of the previously mentioned parameters were correlated with some important physicochemical characteristics of biomass char. Analyses were also performed on complementary pyrolytic products (bio-oil and gas). The biomass char extraction was performed using a Soxhlet and dichloromethane was used as extracting solvent. The extracts were then characterized by GC-MS thus allowing the identification of several compounds. Specific pyrolysis conditions used at 300 °C - N2 with the 1 g/batch reactor, such as high heating rates as well as high convection conditions, presented advantegeous biomass char yields and properties, and, possible torrefaction process productivity improvement (in comparison to reported literature, such as Gilbert et al. [2009]). The char extracts as well as the bio-oils analysis (also performed using GC-MS), all generated from the 25 g/batch reactor, showed major differences among the compounds obtained from the CO2 and N2 environments, respectively. Several compounds observed in the char extracts appeared less concentrated in the CO2 environment vs N2, for the same reaction temperatures. As an example, at 400 °C, furfural was found only in char extracts from N2 environment as compared to the CO2 environment. Among all studied conditions (for both reactors), only naphthalene and naphthalene derivatives constituted the PAHs content, which was only detected for the chars produced at 500 °C. The use of CO2 as pyrolysis vector gas led to a significant difference for every temperature conditions studied for the biomass char as well as for the liquid and gas products. At 300 °C, in CO 2 environment, it is possible to observe a bio-oil production significantly lower than within a N2 environment (18.0 vs 24.6 %; CO2 vs N2 for P<0.002), a result consistent with the biomass char volatile content that was shown to be significantly higher under the same conditions (0.29 vs 0.35 gchar volatiles content/graw biomass; P=0.1). In addition, at 500 °C, the char ash content was observed to be significantly lower in CO 2 than in N2 (P<0.06). Keywords: Pyrolysis, torrefaction, char, biochar, biocoal, CO 2, Soxhlet extractions, characterization.

Pyrolysis of hornbeam (Carpinus betulus L.) sawdust: Characterization of bio-oil and bio-char.

PubMed

Moralı, Uğur; Yavuzel, Nazan; Şensöz, Sevgi

2016-12-01

Slow pyrolysis of hornbeam (Carpinus betulus L.) sawdust was performed to produce bio-oil and bio-char. The operational variables were as follows: pyrolysis temperature (400-600°C), heating rate (10-50°Cmin -1 ) and nitrogen flow rate (50-150cm 3 min -1 ). Physicochemical and thermogravimetric characterizations of hornbeam sawdust were performed. The characteristics of bio-oil and bio-char were analyzed on the basis of various spectroscopic and chromatographic techniques such as FTIR, GC-MS, 1H NMR, SEM, BET. Higher heating value, density and kinematic viscosity of the bio-oil with maximum yield of 35.28% were 23.22MJkg -1 , 1289kgm -3 and 0.6mm 2 s -1 , respectively. The bio-oil with relatively high fuel potential can be obtained from the pyrolysis of the hornbeam sawdust and the bio-char with a calorific value of 32.88MJkg -1 is a promising candidate for solid fuel applications that also contributes to the preservation of the environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis of improved phenolic resins

NASA Technical Reports Server (NTRS)

Delano, C. B.; Mcleod, A. H.

1979-01-01

Twenty seven addition cured phenolic resin compositions were prepared and tested for their ability to give char residues comparable to state-of-the-art phenolic resins. Cyanate, epoxy, allyl, acrylate, methacrylate and ethynyl derivatized phenolic oligomers were investigated. The novolac-cyanate and propargyl-novolac resins provided anaerobic char yields at 800 C of 58 percent. A 59 percent char yield was obtained from modified epoxy novolacs. A phosphonitrilic derivative was found to be effective as an additive for increasing char yields. The novolac-cyanate, epoxy-novolac and methacrylate-epoxy-novolac systems were investigated as composite matrices with Thornel 300 graphite fiber. All three resins showed good potential as composite matrices. The free radical cured methacrylate-epoxy-novolac graphite composite provided short beam shear strengths at room temperature of 93.3 MPa (13.5 ksi). The novolac-cyanate graphite composite produced a short beam shear strength of 74 MPa (10.7 ksi) and flexural strength of 1302 MPa (189 ksi) at 177 C. Air heat aging of the novolac-cyanate and epoxy novolac based composites for 12 weeks at 204 C showed good property retention.

Organic compounds leached from fast pyrolysis mallee leaf and bark biochars.

PubMed

Lievens, Caroline; Mourant, Daniel; Gunawan, Richard; Hu, Xun; Wang, Yi

2015-11-01

Characterization of organic compounds leached from biochars is essential in assessing the possible toxicity of the biochar to the soils' biota. In this study the nature of the leached organic compounds from Mallee biochars, produced from pyrolysis of Mallee leaf and bark in a fluidised-bed pyrolyser at 400 and 580°C was investigated. Light bio-oil compounds and aromatic organic compounds were investigated. The 'bio-oil like' light compounds from leaf and bark biochars 'surfaces were obtained after leaching the chars with a solvent, suitable to dissolve the respective bio-oils. GC/MS was implemented to investigate the leachates. Phenolics, which are potentially harmful toxins, were detected and their concentration shown to be dependent on the char's origin and the char production temperature. Further, to simulate biochars amendment to soils, the chars were leached with water. The water-leached aromatic compounds from leaf and bark biochars were characterized using UV-fluorescence spectroscopy. Those results suggested that biochars contain leachable compounds of which the nature and amount is dependent on the biomass feedstock, pyrolysis temperature and leaching time. Copyright © 2014 Elsevier Ltd. All rights reserved.

Molecular Analysis of Flood Deposits in the Tennessee River Valley: Implications for Understanding Carbon Cycling in Fluvial Environments and Anthropogenic Impacts

NASA Astrophysics Data System (ADS)

Blackaby, E.; Craven, O. D.; Hockaday, W. C.; Forman, S. L.; Stinchcomb, G. E.

2017-12-01

The middle Tennessee River Valley contains both historic and prehistoric (>AD 1600) flood deposits. Stratigraphic sequences of stacked flood deposits that often bury soils provide new insights on organic matter transported and preserved prior to and after European colonization. This study focused on understanding carbon cycling within a dynamic fluvial system and quantifying the anthropogenic effect on flood processes through the analysis of molecular components of the organic matter. The data may be helpful in discerning the organic geochemical fingerprint for historic and prehistoric flood deposits. Ten samples were collected from three sites at varying depths and dated using optically stimulated luminescence (OSL). All samples underwent solid-state cross polar 13C NMR analysis at twelve kilohertz, and a molecular mixing model (MMM) was used to determine the molecular components of the organic matter present in each sample. The MMM categorized carbon molecules present in each sample in terms of carbohydrate, protein, lipid, lignin, char, or pure carbonyl. Char was the most prominent molecular component of all ten samples ranging from 28.7 to 55.9% and comprised larger percentages in prehistoric deposits. The historic deposits, while still char dominated, showed more molecular diversity with higher percentages in non-char carbon groups. The carbonyl, lipid, and carbohydrate groups are present throughout all the samples with the carbonyl ranging from 9.3 to 31.4%, the lipid from 5.5 to 16.7%, and the carbohydrate from 4.4 to 16.9%. The high amount of carbonyl throughout the samples indicates that the deposits existed in a highly oxidizing environment. Differences in the presence and amount of carbon groups between historic and prehistoric flood deposits potentially reflect diagenic alternation of organic matter through time, changes in human land use, or some combination processes. These preliminary results possibly indicate changes in carbon pools accessed with European cultivation and continued degradation of organic moieties during a ca. 400 years burial, and mostly in oxidizing conditions.

Characteristics and sources of the fine carbonaceous aerosols in Haikou, China

NASA Astrophysics Data System (ADS)

Liu, Baoshuang; Zhang, Jiaying; Wang, Lu; Liang, Danni; Cheng, Yuan; Wu, Jianhui; Bi, Xiaohui; Feng, Yinchang; Zhang, Yufen; Yang, Haihang

2018-01-01

Ambient PM2.5 samples were collected from January to September 2015 in Haikou. The carbonaceous fractions included OC, EC, OC1, OC2, OC3, OC4, EC1, EC2, EC3, Char-EC (EC1 minus POC) and Soot-EC (EC2 plus EC3) were analysed in this study. The results indicate that the mean concentrations of OC and EC are 5.6 and 2.5 μg/m3 during the sampling period, respectively; and the concentrations of most of carbonaceous fractions are the highest in winter and the lowest in spring. The seasonal variations of Soot-EC and Char-EC concentrations show distinct differences. The concentrations of Char-EC are higher in winter and lower in spring; while those of Soot-EC are lower in winter and higher in summer. Compared to Char-EC, the concentrations of Soot-EC show smaller seasonal-variation in Haikou. The Char-EC has the higher correlations with OC and EC (r = 0.91 and 0.95, P < 0.01), while the correlation between the Soot-EC and either OC or EC is absent (r = 0.15 and 0.11, P > 0.05). The average ratios of Char-EC/Soot-EC are in the order of winter (15.9) > autumn (4.9) > summer (4.0) > spring (3.6), with an average value of 7.1. According to error estimation (EE) diagnostics analysis, four factors are revealed in Positive Matrix Factorization (PMF) analysis during each season. The combined gasoline/diesel vehicle exhaust, coal combustion, biomass burning and specific diesel vehicle exhaust are identified as the major sources of carbonaceous aerosols, and their contributions during the whole year are up to 29.3%, 27.4%, 17.9% and 15.9%, respectively. The transport trajectories of the air masses illustrate distinct differences during different seasons, and the transport trajectories are mainly derived from the mainland China (i.e. Jiangxi, Fujian and Guangdong provinces) in winter, likely caused by higher contribution of coal combustion.

Using BPCA and pyrolysis-GC/MS patterns as a measure of charring intensity

NASA Astrophysics Data System (ADS)

Kaal, Joeri; Schneider, Maximilian P. W.; Schmidt, Michael W. I.

2010-05-01

Many questions remain on the molecular properties of Black C (organic fire residues such as charcoal and soot). Here we compare parameters from two methods that have recently shown to be related to the degree of thermal modification ("charring intensity") of charcoal-Black C: i) the proportion of mellitic acid (B6CA) among benzenepolycarboxylic acids in the BPCA method [1,2,3] and ii) the relative proportions and degree of alkylation of pyrolysis products from Black C in pyrolysis-GC/MS [4]. For that purpose we used laboratory chars from rice straw (grass) and chestnut wood (wood) produced at 200-1000 °C under N2 flow. The chars obtained at 450 °C are reference materials of the Black Carbon Ring Trial [5]. Positive correlations between the charring temperature and BPCA and pyrolysis patterns confirm that these methods can be used to study the degree of thermal impact of charred remains. Pyrolysis-GC/MS allowed us to track the thermal degradation of the major biocomponents lignin, polysaccharides, tannin, aliphatic chain lipids, triterpenoids, chlorophyll and proteins, mostly between 250 and 450 °C. The proportions of the pyrolysis products of Black C (benzene, toluene, benzonitrile, PAHs, etc.) and also the ratios that reflect the abundance of aliphatic cross-linkages between aromatic moieties (benzene/toluene, naphthalene/alkylnaphthalenes, benzofuran/alkylbenzofurans), increase with charring intensity. Nonetheless, chars obtained at T > 600 °C (especially for wood) gave low quality pyrograms and poor reproducibility because of high thermal stability. The relative contributions of B6CA, one of the molecular markers used for the BPCA method, are indicative for the degree of condensation of the chars. The BPCA approach showed a clear increase in the relative contribution of B6CA from ca. 5 % at 200 °C to ca. 95 % at 1000 °C, confirming the ability of this parameter to assess charring intensity. The relative contribution of B6CA remains almost constant at ca. 30 % between 250 and 450 °C. Thus, with regard to estimating the charring intensity of Black C, the BPCA method is more suitable for high T chars (> 450 °C) while pyrolysis-GC/MS seems more appropriate in the lower T range (< 500 °C). This is not surprising as larger clusters of polyaromatic domains (high T) can be assessed by the BPCA method but are resistant against pyrolysis. On the other hand, smaller clusters and non-polycondensed portions of Black C (low T) are amenable to pyrolysis-GC/MS but escape the analytical window of the BPCA method. The two methods may therefore be considered complementary, with BPCA giving reliable quantitative data on Black C content and charring degree of high T chars while pyrolysis-GC/MS is quantitatively weak but provides highly detailed information on the molecular properties of especially lower T chars. References [1] Brodowski, S., Rodionov, A., Haumeier L., Glaser, B., Amelung, W. (2005) Org. Geochem. 36, 1299-1310. [2] Glaser, B., Haumeier, L., Guggenberger, G., Zech, W. (1998) Org. Geochem. 29, 811-819. [3] Schneider, M.P.W., Hilf, M., Vogt, U.F., Schmidt, M.W.I., Org. Geochem. (submitted) [4] Kaal, J., Rumpel, C. (2009) Org. Geochem. 40, 1179-1187. [5] Hammes, K., Schmidt, M.W.I., Smernik, R.J. et al. (2007) Global Biogeochemical Cycles 21, 1-18.

Influence of combustion conditions on yields of solvent-extractable anhydrosugars and lignin phenols in chars: implications for characterizations of biomass combustion residues.

PubMed

Kuo, Li-Jung; Louchouarn, Patrick; Herbert, Bruce E

2011-10-01

Anhydrosugars, such as levoglucosan and its isomers (mannosan, galactosan), as well as the solvent-extractable lignin phenols (methoxylated phenols) are thermal degradation products of cellulose/hemicellulose and lignin, respectively. These two groups of biomarkers are often used as unique tracers of combusted biomass inputs in diverse environmental media. However, detailed characterization of the relative proportion and signatures of these compounds in highly heterogeneous plant-derived chars are still scarce. Here we conducted a systematic study to investigate the yields of solvent-extractable anhydrosugars and lignin phenols in 25 lab-made chars produced from different plant materials under different combustion conditions. Solvent-extractable anhydrosugars and lignin phenols were only observed in chars formed below 350°C and yields were variable across different combustion temperatures. The yields of mannosan (M) and galactosan (G) decreased more rapidly than those of levoglucosan (L) under increasing combustion severity (temperature and duration), resulting in variable L/M and L/(M+G) ratios, two diagnostic ratios often used for identification of combustion sources (e.g. hardwoods vs. softwoods vs. grasses). Our observations thus may provide an explanation for the wide ranges of values reported in the literature for these two ratios. On the other hand, the results of this study suggest that the ratios of the major solvent-extractable lignin phenols (vanillyls (V), syringyls (S), cinnamyls (C)) provide additional source reconstruction potential despite observed variations with combustion temperature. We thus propose using a property-property plot (L/M vs. S/V) as an improved means for source characterization of biomass combustion residues. The L/M-S/V plot has shown to be effective in environmental samples (soil organic matter, atmospheric aerosols) receiving substantial inputs of biomass combustion residues. Copyright © 2011 Elsevier Ltd. All rights reserved.

Materials characterization on efforts for ablative materials

NASA Technical Reports Server (NTRS)

Tytula, Thomas P.; Schad, Kristin C.; Swann, Myles H.

1992-01-01

Experimental efforts to develop a new procedure to measure char depth in carbon phenolic nozzle material are described. Using a Shor Type D Durometer, hardness profiles were mapped across post fired sample blocks and specimens from a fired rocket nozzle. Linear regression was used to estimate the char depth. Results are compared to those obtained from computed tomography in a comparative experiment. There was no significant difference in the depth estimates obtained by the two methods.

HIGH PRESSURE COAL COMBUSTON KINETICS PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stefano Orsino

As part of the U.S. Department of Energy (DoE) initiative to improve the efficiency of coal-fired power plants and reduce the pollution generated by these facilities, DOE has funded the High-Pressure Coal Combustion Kinetics (HPCCK) Projects. A series of laboratory experiments were conducted on selected pulverized coals at elevated pressures with the specific goals to provide new data for pressurized coal combustion that will help extend to high pressure and validate models for burnout, pollutant formation, and generate samples of solid combustion products for analyses to fill crucial gaps in knowledge of char morphology and fly ash formation. Two seriesmore » of high-pressure coal combustion experiments were performed using SRI's pressurized radiant coal flow reactor. The first series of tests characterized the near burner flame zone (NBFZ). Three coals were tested, two high volatile bituminous (Pittsburgh No.8 and Illinois No.6), and one sub-bituminous (Powder River Basin), at pressures of 1, 2, and 3 MPa (10, 20, and 30 atm). The second series of experiments, which covered high-pressure burnout (HPBO) conditions, utilized a range of substantially longer combustion residence times to produce char burnout levels from 50% to 100%. The same three coals were tested at 1, 2, and 3 MPa, as well as at 0.2 MPa. Tests were also conducted on Pittsburgh No.8 coal in CO2 entrainment gas at 0.2, 1, and 2 MPa to begin establishing a database of experiments relevant to carbon sequestration techniques. The HPBO test series included use of an impactor-type particle sampler to measure the particle size distribution of fly ash produced under complete burnout conditions. The collected data have been interpreted with the help of CFD and detailed kinetics simulation to extend and validate devolatilization, char combustion and pollutant model at elevated pressure. A global NOX production sub-model has been proposed. The submodel reproduces the performance of the detailed chemical reaction mechanism for the NBFZ tests.« less

Characterization of fuels for second-generation PFBC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zevenhoven, C.A.P.; Hupa, M.

1997-12-31

In second-generation PFBC technology a solid fuel is partly converted in a devolatilization step (in a carbonizer) to produce a char and a pressurized fuel gas, followed by PFB combustion of the char. The fuel gas is led to the combustion chamber of a gas turbine after it is mixed with the PFBC off-gas, thus increasing the temperature at the inlet of the expansion turbine. Clearly, the optimization of the carbonizer design and operation is essential to the process. Detailed information on the behavior of solid fuels under pressurized conditions is, however, largely limited to steam and/or carbon dioxide gasificationmore » reactivities, obtained at a different combination of process parameters, such as temperature, pressure, heating rate, particle size and gas atmosphere. In the present work, the effect of temperature, pressure and heating rates on the yields of volatiles and char residue reactivity has been measured for a set of fuels ranging from bituminous coal to wood. Laboratory conditions were typical for the carbonizer and combustion reactors in a second-generation PFBC system. A pressurized thermogravimetric reactor (PTGR) operated at heating rates of around 250 K/s and a pressurized grid heater (PGH) operated at heating rates up to 3,000 K/s were used to analyze fuel devolatilization and char reactivity against carbon dioxide or steam at temperatures between 800 and 1,100 C, and 1, 10 or 25 bar total pressure. For comparison, a few experiments were repeated without a separate devolatilization step. The behavior of the various fuels were compared and related to proximate and ultimate fuel analysis. Several empirical, engineering equations are given. A simple 2-parameter model which separates intrinsic surface reactivity and physical, structure effects, very well describes the time-conversion data of the char. It was found that the fuel O/C molar ratio is a very good index for char reactivity, when the char O/C ratio itself is unknown.« less

A PC Program to Calculate the One-Sided Lower Tolerance Limit for Total Ionizing Dose Radiation Data

DTIC Science & Technology

1991-08-01

include <graphics .h> #define VEDIO OxlO #define ESC 27 1* Decelerations * FILE *pfile; FILE *outf; FILE *inf; mnt n; mnt un; float max scale...regs.h.ah=2; regs .h.dh=y; regs .h.dl=x; regs .h.bh=O; int86( VEDIO , ®s, ®s); char attribute(char blink, char back-color,char intensity, char...set lint mode) union REGS regs; regs.h.ah=O; regs h a l-mode; int86( VEDIO , ®s, ®s); void str-color (char x, char y, char *str, char blink, char

The influence of wildfire severity on soil char composition and nitrogen dynamics

NASA Astrophysics Data System (ADS)

Rhoades, Charles; Fegel, Timothy; Chow, Alex; Tsai, Kuo-Pei; Norman, John, III; Kelly, Eugene

2017-04-01

Forest fires cause lasting ecological changes and alter the biogeochemical processes that control stream water quality. Decreased plant nutrient uptake is the mechanism often held responsible for lasting post-fire shifts in nutrient supply and demand, though other upland and in-stream factors also likely contribute to elevated stream nutrient losses. Soil heating, for example, creates pyrogenic carbon (C) and char layers that influence C and nitrogen (N) cycling. Char layer composition and persistence vary across burned landscapes and are influenced first by fire behavior through the temperature and duration of combustion and then by post-fire erosion. To evaluate the link between soil char and stream C and N export we studied areas burned by the 2002 Hayman Fire, the largest wildfire in Colorado, USA history. We compared soil C and N pools and processes across ecotones that included 1) unburned forests, 2) areas with moderate and 3) high wildfire severity. We analyzed 1-2 cm thick charred organic layers that remain visible 15 years after the fire, underlying mineral soils, and soluble leachate from both layers. Unburned soils released more dissolved organic C and N (DOC and DON) from organic and mineral soil layers than burned soils. The composition of DOC leachate characterized by UV-fluorescence, emission-excitation matrices (EEMs) and Fluorescence Regional Integration (FRI) found similarity between burned and unburned soils, underscoring a common organic matter source. Humic and fulvic acid-like fractions, contained in regions V and III of the FRI model, comprised the majority of the fluorescing DOM in both unburned and char layers. Similarity between two EEMs indices (Fluorescence and Freshness), further denote that unburned soils and char layers originate from the same source and are consistent with visual evidence char layers contain significant amounts of unaltered OM. However, the EEMs humification index (HIX) and compositional analysis with pyrolysis GCMS both indicate that C contained or leached from severely-burned char layers has higher aromaticity and thus chemical stability compared to C in unburned soils. Mineral soil (0-5 cm depth) beneath char layers in high severity portions of the Hayman Fire had significantly more soil N and C and lower pH. Potential net mineralization - an index of the supply of plant-available nitrogen - differed between the severely-burned areas and both unburned and moderately-burn areas. Negative net mineralization in unburned and moderately burned soils indicates immobilization or retention of inorganic N by soil microbes. In contrast, soils burned at high severity produced inorganic N sources available to plants, leaching and gas losses. Water soluble nitrate comprised a larger proportion of inorganic N leached from the char layer of high severity burns. Mineral soil in those areas had both higher water soluble nitrate and total inorganic N in leachate. Char layers that have persisted for fifteen years influence soil N turnover within the Hayman Fire affected area and may contribute to elevated N losses in streams burned at high severity. The chemical stability of soil char layers perpetuates their importance for C sequestration and N dynamics in burned landscapes.

Who Set the Fire? Determination of Arson Accelerants by GC-MS in an Instrumental Methods Course

NASA Astrophysics Data System (ADS)

Sodeman, David A.; Lillard, Sheri J.

2001-09-01

Forensic scenarios have advantages over traditional experiments in the instrumental laboratory from the perspectives of both teaching and learning. First, students feel that they are calculating more than just a number from their experiments and that their results have meaning. Second, we are teaching techniques that are used in the real world and students can no longer complain, "This is not how it is done in the real world." This experiment is designed for upper-division chemistry and chemical engineering majors taking an instrumental methods course. The experimental approach simulates the steps an arson investigator would take to determine if arson was the cause of a fire. Charred (unknown) samples of wood and five standards of liquid accelerants are prepared in sealed containers and presented to the students for headspace gas chromatography (GC) with quadrupole mass spectrometric (MS) detection. Students interpret the standards and the charred samples using chromatographic retention times and MS data. From this information, they determine which accelerant was used to start the fire. They are also asked to discuss differences between the chromatograms of the charred sample and the corresponding liquid accelerant.

Effects of catalysts on combustion characteristics and kinetics of coal-char blends

NASA Astrophysics Data System (ADS)

Hu, Yingjie; Wang, Zhiqiang; Cheng, Xingxing; Liu, Ming; Ma, Chunyuan

2018-04-01

The effects of Fe2O3, CaO, and MnO2 on the combustion characteristics and kinetics of coal-char blends were investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results indicated that catalysts exhibited positive effects on the combustion characteristics of coal-char blends, especially in the initial period of coal-char blends combustion. With catalysts addition (mass 1.5%), it could improves volatile matter release, and reduces ignition point, promotes char to begin burning under lower temperature. The ignition index (C) was increased, respectively, by 27% for Fe2O3, 6% for CaO, 11.3% for MnO2, and the combustion characteristic index ( S ) was increased respectively, by 29% for Fe2O3, 5% for CaO, 8.3% for MnO2. In addition, two kinetic models (R2 and F1) were adopted to calculate the kinetic parameters in different stage of combustion processes. The results showed that with Fe2O3 or CaO addition, the activation energy at second stage decreases from 86.0 KJ/mol to 76.92 KJ/mol and 75.12 KJ/mol, respectively. There are no obvious decreases at the third stage of samples combustion process.

Hydrothermal carbonization of Opuntia ficus-indica cladodes: Role of process parameters on hydrochar properties.

PubMed

Volpe, Maurizio; Goldfarb, Jillian L; Fiori, Luca

2018-01-01

Opuntia ficus-indica cladodes are a potential source of solid biofuel from marginal, dry land. Experiments assessed the effects of temperature (180-250°C), reaction time (0.5-3h) and biomass to water ratio (B/W; 0.07-0.30) on chars produced via hydrothermal carbonization. Multivariate linear regression demonstrated that the three process parameters are critically important to hydrochar solid yield, while B/W drives energy yield. Heating value increased together with temperature and reaction time and was maximized at intermediate B/W (0.14-0.20). Microscopy shows evidence of secondary char formed at higher temperatures and B/W ratios. X-ray diffraction, thermogravimetric data, microscopy and inductively coupled plasma mass spectrometry suggest that calcium oxalate in the raw biomass remains in the hydrochar; at higher temperatures, the mineral decomposes into CO 2 and may catalyze char/tar decomposition. Copyright © 2017 Elsevier Ltd. All rights reserved.

Interaction of graphite and ablative materials with CO2-laser, carbon-arc, and xenon-arc radiation. M.S. Thesis - George Washington Univ., Washington, D. C.

NASA Technical Reports Server (NTRS)

Brewer, W. D.

1975-01-01

The behavior of graphite and several charring ablators in a variety of high radiative heat flux environments was studied in various radiative environments produced by a CO2 laser and a carbon arc facility. Graphite was also tested in xenon arc radiation. Tests were conducted in air nitrogen, helium, and a mixture of CO2 and nitrogen, simulating the Venus atmosphere. The experimental results are compared with theoretical results obtained with a one dimensional charring ablator analysis and a two dimensional subliming ablator analysis. Photomicroscopy showed no significant differences in appearance or microstructure of the charring ablators or graphite after testing in the three different facilities, indicating that the materials respond fundamentally the same to the radiation of different frequencies. The performance of phenolic nylon and graphite was satisfactorily predicted with existing analyses and published material property data.

Impact of the lignocellulosic material on fast pyrolysis yields and product quality.

PubMed

Carrier, Marion; Joubert, Jan-Erns; Danje, Stephen; Hugo, Thomas; Görgens, Johann; Knoetze, Johannes Hansie

2013-12-01

The paper describes the fast pyrolysis conversion of lignocellulosic materials inside a bubbling fluidized bed. The impact of biopolymers distribution in the biomass feed, namely hemicelluloses, cellulose and lignin, on the yields and properties of pyrolytic bio-oils and chars was investigated. Although it is not possible to deconvoluate chemical phenomena from transfer phenomena using bubbling fluidized bed reactors, the key role of hemicelluloses in biomass feedstocks was illustrated by: (i) its influence on the production of pyrolytic water, (ii) its impact on the production of organics, apparently due to its bonding relationship with the lignin and (iii) its ability to inhibit the development of chars porosity, while the cellulose appeared to be the precursor for the microporous character of the biochars. These results are of interest for the selection of suitable feedstocks aimed at producing bio-oil and char as fuels and soil amendment, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Studies of the physical aspects of intumescence using advance diagnostics methods

NASA Astrophysics Data System (ADS)

Saeed, Hussain; Huang, Hua Wei; Zhang, Yang

2014-04-01

The use of intumescent paints as an active fire protection method has gained immense interest in recent years. A significant aspect of research has focused on studying the chemical aspects of the system to improve performance. The dynamics and physical aspects of intumescence in real time fire conditions are still unclear. The present research uses an experimental approach where diagnostics techniques such as thermal imaging camera was used to study intumescent characteristics that have been not been reported in great detail. T-panels are a substitute to the most commonly used part in construction, the I-beam. Studies were conducted using a cone calorimeter that provided a uniform heat flux through radiation on steel T-panel samples. The complex nature of char movement was recorded and a novel algorithm was used to track the growing char laye07r. The samples are designed to cater to different fire conditions. Therefore, the degree of intumescence was observed to be very different in the samples. The samples designed for low temperature cellulosic fires focus on high degree of intumesce. Whereas, mechanical strength is the focus for samples used in high temperature turbulent hydrocarbon fire conditions. The variation in the internal structure of the sample is presented. Furthermore, the phenomenon is phase shift is discussed. The phase shift is an essential part of the process of intumescence when the majority of intumescence occurs. It was observed to be different in all the samples. The movement of the samples is a property of great interest. This is because if any part of the substrate is exposed then the formulation does not meet strict commercialisation criterion. The movement was diagonal in nature as compared to flat panels where it is perpendicular. This is due tot the heating pattern of the plate that results in the web part of the panel to influence the growth of char on the flange part of the panel. A special case of char cracking is also highlighted and using image processing algorithm on the thermal imaging data. A quantitative method of analsysis is presented to an otherwise commonly qualitative nature of experimental study in this field.

Effects of nano-sized boron nitride (BN) reinforcement in expandable graphite based in-tumescent fire retardant coating

NASA Astrophysics Data System (ADS)

Zulkurnain, E. S.; Ahmad, F.; Gillani, Q. F.

2016-08-01

The purpose of in-tumescent fire retardant coating (IFRC) is to protect substrate from fire attack by limiting heat transfer. A range of coating formulations have been prepared using Bisphenol A epoxy resin BE-188 and polyamide solidifier H-2310 as two-part binder, ammonium polyphosphate (APP) as acid source, melamine (MEL) as the blowing agent, expandable graphite (EG) as carbon source and nano-boron nitride (BN) as inorganic nano filler. The filler was used to improve the performances of the APP-EG-MEL coating. The effects of nano-BN on the char morphology and thermal degradation were investigated by fire test, thermo gravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), X- ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FESEM). The results showed that by substituting or reinforcing of 4% weight percentage of nano-BN, residual weight of the char increases by 23.82% compared to APP-EG-MEL coating without filler. Higher carbon content was obtained in the char and a more compact char was produced. The results indicated that nano-BN could be used as a filler to improve thermal stability of the APP-EG-MEL coating.

Mission analysis for the federal fuels from biomass program. Volume IV. Termochemical conversion of biomass to fuels and chemicals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kohan, S.M.; Barkhordar, P.M.

1979-01-01

The thermochemical conversion of biomass feedstocks generally denotes technologies that use elevated temperatures to convert the fixed carbon content of biomass materials to produce other, more useful energy forms. Examples are combustion to produce heat, steam, electricity, or combinations of these; pyrolysis to produce gas (low- or intermediate-Btu), pyrolytic liquids and chemicals, and char; gasification to produce low or intermediate Btu gas (and, from IBG, additional products such as SNG, ammonia, methanol, or Fischer-Tropsch liquids); and liquefaction to produce heavy fuel oil or, with upgrading, lighter-boiling liquid products such as distillates, light fuel oils, or gasoline. This section discusses themore » selection of the feedstock used in the analysis of thermochemical conversion technologies. The following sections present detailed technical and economic evaluations of biomass conversion to electricity and steam by combustion, SNG by gasification and methanation, methanol by gasification and synthesis, oil by catalytic liquefaction, oil and char by pyrolysis, and ammonia by gasification and synthesis. The conversion options were reviewed with DOE for approval at the start of the project.« less

Fast pyrolysis of tropical biomass species and influence of water pretreatment on product distributions

DOE PAGES

Morgan, Trevor James; Turn, Scott Q.; Sun, Ning; ...

2016-03-15

Here, the fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amountmore » of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO 2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO 2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena.« less

Fast pyrolysis of tropical biomass species and influence of water pretreatment on product distributions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, Trevor James; Turn, Scott Q.; Sun, Ning

Here, the fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amountmore » of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO 2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO 2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena.« less

Fast Pyrolysis of Tropical Biomass Species and Influence of Water Pretreatment on Product Distributions

PubMed Central

Morgan, Trevor James; Turn, Scott Q.; Sun, Ning; George, Anthe

2016-01-01

The fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amount of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena. PMID:26978265

Fast Pyrolysis of Tropical Biomass Species and Influence of Water Pretreatment on Product Distributions.

PubMed

Morgan, Trevor James; Turn, Scott Q; Sun, Ning; George, Anthe

2016-01-01

The fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amount of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena.

Development of carbon dioxide adsorbent from rice husk char

NASA Astrophysics Data System (ADS)

Abang, S.; Janaun, J.; Anisuzzaman, S. M.; Ikhwan, F. S.

2016-06-01

This study was mainly concerned about the development of carbon dioxide (CO2) adsorbent from rice husk (RH). Several chemical treatments were used to produce activated rice husk char (RHAC) from RH. Initially the RH was refluxed with 3M of sodium hydroxide (NaOH) solution, activation followed by using 0.5M of zinc chloride (ZnCl2) solution and finally acidic treatment by using 0.1M of hydrochloric acid (HCl). Then, the RHAC was functionalized by using 3-chloropropylamine hydrochloride (3-CPA) and noted as RHN. RHN samples were characterized with scanning electron microscopy (SEM), mercury intrusion porosimetry (MIP), fourier transform infrared spectroscopy (FTIR). Based on the SEM, the RHN sample had a large pore diameter compared to RH sample after being treated. Based on MIP data, the average pore diameter between RH and RHAC samples were increased significantly from 0.928 microns to 1.017 microns. The RHN sample also had higher total porosity (%) compared to RHAC and RH (58.45%, 47.82% and 45.57% respectively). The total specific surface area of the sample was much increasing from RHO to RHAC (29.17 m2/g and 62.94 m2/g respectively) and slightly being decreasing from RHAC to RHN (58.88 m2/g). FTIR result showed the present of weak band at 1587 cm-1 which demonstrating of the amine group present on the sample. The CO2 capture result showed that the decreasing of operating temperature can increase the breakthrough time of CO2 capture. On the contrary decreasing of CO2 gas flow rate can increase the breakthrough time of CO2 capture. The highest total amount of CO2 adsorbed was 25338.57 mg of CO2/g of RHN sample by using 100 mL/min of gas flow rate at 30oC. Based on adsorption isotherm analysis, the Freundlich isotherm was the best isotherm to describe the CO2 adsorption on the sample.

Combustion heater for oil shale

DOEpatents

Mallon, R.; Walton, O.; Lewis, A.E.; Braun, R.

1983-09-21

A combustion heater for oil shale heats particles of spent oil shale containing unburned char by burning the char. A delayed fall is produced by flowing the shale particles down through a stack of downwardly sloped overlapping baffles alternately extending from opposite sides of a vertical column. The delayed fall and flow reversal occurring in passing from each baffle to the next increase the residence time and increase the contact of the oil shale particles with combustion supporting gas flowed across the column to heat the shale to about 650 to 700/sup 0/C for use as a process heat source.

Combustion heater for oil shale

DOEpatents

Mallon, Richard G.; Walton, Otis R.; Lewis, Arthur E.; Braun, Robert L.

1985-01-01

A combustion heater for oil shale heats particles of spent oil shale containing unburned char by burning the char. A delayed fall is produced by flowing the shale particles down through a stack of downwardly sloped overlapping baffles alternately extending from opposite sides of a vertical column. The delayed fall and flow reversal occurring in passing from each baffle to the next increase the residence time and increase the contact of the oil shale particles with combustion supporting gas flowed across the column to heat the shale to about 650.degree.-700.degree. C. for use as a process heat source.

Cyanate Ester and Phthalonitrile Impregnated Carbon Ablative TPS

NASA Technical Reports Server (NTRS)

Boghozian, Tane; Stackpoole, Margaret M.; Gasch, Matt

2016-01-01

Phenolic resin has extensive heritage as a TPS (Thermal Protection Systems) material, however, alternative resin systems such as Cyanate Ester and Phthalonitrile may offer improved performance compared to state-of-the-art phenolic resin. These alternative resin systems may have higher char yield, higher char strength, lower thermal conductivity and improved mechanical properties. In current work at NASA Ames alternative resin systems were uniformly infused into fibrous substrates and preliminary properties characterized. The density of the cyanate ester infused in fibrous substrate ranged from 0.25-0.3 grams per cubic centimeter compared to PICA (Phenolic resin impregnated carbon ablative) having a density of approximately 0.25 grams per cubic centimeter. The density of Phthalonitrile varies from 0.22-0.25 grams per cubic centimeter. Initial formulations of these new resin systems were recently tested at the LARC HyMETs (Hypersonic Materials Environmental Test System) facility to evaluate their performance and data such as back face temperature, char yield, and recession are compared to PICA. Cyanate Ester and Phthalonitrile impregnated carbon ablative samples showed comparable performance to phenolic resin impregnated carbon ablative samples.

Impact of contamination and pre-treatment on stable carbon and nitrogen isotopic composition of charred plant remains

PubMed Central

Vaiglova, Petra; Snoeck, Christophe; Nitsch, Erika; Bogaard, Amy; Lee-Thorp, Julia

2014-01-01

Rationale Stable isotope analysis of archaeological charred plants has become a useful tool for interpreting past agricultural practices and refining ancient dietary reconstruction. Charred material that lay buried in soil for millennia, however, is susceptible to various kinds of contamination, whose impact on the grain/seed isotopic composition is poorly understood. Pre-treatment protocols have been adapted in distinct forms from radiocarbon dating, but insufficient research has been carried out on evaluating their effectiveness and necessity for stable carbon and nitrogen isotope analysis. Methods The effects of previously used pre-treatment protocols on the isotopic composition of archaeological and modern sets of samples were investigated. An archaeological sample was also artificially contaminated with carbonates, nitrates and humic acid and subjected to treatment aimed at removing the introduced contamination. The presence and removal of the contamination were investigated using Fourier transform infrared spectroscopy (FTIR) and δ13C and δ15N values. Results The results show a ca 1‰ decrease in the δ15N values of archaeological charred plant material caused by harsh acid treatments and ultra-sonication. This change is interpreted as being caused by mechanical distortion of the grains/seeds rather than by the removal of contamination. Furthermore, specific infrared peaks have been identified that can be used to detect the three types of contaminants studied. We argue that it is not necessary to try to remove humic acid contamination for stable isotope analysis. The advantages and disadvantages of crushing the grains/seeds before pre-treatment are discussed. Conclusions We recommend the use of an acid-only procedure (0.5 M HCl for 30 min at 80°C followed by three rinses in distilled water) for cleaning charred plant remains. This study fills an important gap in plant stable isotope research that will enable future researchers to evaluate potential sources of isotopic change and pre-treat their samples with methods that have been demonstrated to be effective. © 2014 The Authors. Rapid Communications in Mass Spectrometry published by John Wiley & Sons Ltd. PMID:25366397

Study on CO2 gasification reactivity and physical characteristics of biomass, petroleum coke and coal chars.

PubMed

Huo, Wei; Zhou, Zhijie; Chen, Xueli; Dai, Zhenghua; Yu, Guangsuo

2014-05-01

Gasification reactivities of six different carbonaceous material chars with CO2 were determined by a Thermogravimetric Analyzer (TGA). Gasification reactivities of biomass chars are higher than those of coke and coal chars. In addition, physical structures and chemical components of these chars were systematically tested. It is found that the crystalline structure is an important factor to evaluate gasification reactivities of different chars and the crystalline structures of biomass chars are less order than those of coke and coal chars. Moreover, initial gasification rates of these chars were measured at high temperatures and with relatively large particle sizes. The method of calculating the effectiveness factor η was used to quantify the effect of pore diffusion on gasification. The results show that differences in pore diffusion effects among gasification with various chars are prominent and can be attributed to different intrinsic gasification reactivities and physical characteristics of different chars. Copyright © 2014 Elsevier Ltd. All rights reserved.

Carbon Sequestration and Nitrogen Mineralization in Soil Cooperated with Organic Composts and Bio-char During Corn (Zea mays) Cultivation

NASA Astrophysics Data System (ADS)

Shin, Joung-Du; Lee, Sun-Ill; Park, Wu-Gyun; Choi, Yong-Su; Hong, Seong-Gil; Park, Sang-Won

2014-05-01

Objectives of this study were to estimate the carbon sequestration and to evaluate nitrogen mineralization and nitrification in soils cooperated with organic composts and bio-char during corn cultivation. For the experiment, the soil used in this study was clay loam types, and application rates of chemical fertilizer and bio-char were recommended amount after soil test and 2 % to soil weight, respectively. The soil samples were periodically taken at every 15 day intervals during the experimental periods. The treatments were consisted of non-application, cow manure compost, pig manure compost, swine digestate from aerobic digestion system, their bio-char cooperation. For the experimental results, residual amount of inorganic carbon was ranged from 51 to 208kg 10a-1 in soil only cooperated with different organic composts. However it was estimated to be highest at 208kg 10a-1 in the application plot of pig manure compost. In addition to bio-char application, it was ranged from 187.8 to 286kg 10a-1, but was greatest accumulated at 160.3kg 10a-1 in the application plot of cow manure compost. For nitrogen mineralization and nitrification rates, it was shown that there were generally low in the soil cooperated with bio-char compared to the only application plots of different organic composts except for 71 days after sowing. Also, they were observed to be highest in the application plot of swine digestate from aerobic digestion system. For the loss of total inorganic carbon (TIC) by run-off water, it was ranged from 0.18 to 0.36 kg 10a-1 in the different treatment plots. Also, with application of bio-char, total nitrogen was estimated to be reduced at 0.42(15.1%) and 0.38(11.8%) kg 10a-1 in application plots of the pig manure compost and aerobic digestate, respectively.

Method for producing and treating coal gases

DOEpatents

Calderon, Albert

1990-01-01

A method of generating a de-sulphurized volatile matter and a relatively low Btu gas includes the initial step of pyrolyzing coal to produce volatile matter and a char. The volatile matter is fed to a first de-sulphurizer containing a de-sulphurizing agent to remove sulphur therefrom. At the same time, the char is gasified to produce a relatively low Btu gas. The low Btu gas is fed to a second de-sulphurizer containing the de-sulphurizing agent to remove sulphur therefrom. A regenerator is provided for removing sulphur from the de-sulphurizing agent. Portions of the de-sulphurizing agent are moved among the first de-sulphurizer, the second de-sulphurizer, and the regenerator such that the regenerator regenerates the de-sulphurizing agent. Preferably, the portions of the de-sulphurizing agent are moved from the second de-sulphurizer to the first de-sulphurizer, from the first de-sulphurizer to the regenerator, and from the regenerator to the second de-sulphurizer.

Characteristics of activated carbon resulted from pyrolysis of the oil palm fronds powder

NASA Astrophysics Data System (ADS)

Maulina, S.; Iriansyah, M.

2018-02-01

Activated carbon is the product of a charcoal impregnation process that has a higher absorption capacity and has more benefits than regular char. Therefore, this study aims to cultivate the powder of oil palm fronds into activated carbon that meets the requirements of Standard National Indonesia 06-3730-1995. To do so, the carbonization process of the powder of oil palm fronds was carried out using a pyrolysis reactor for 30 minutes at a temperature of 150 °C, 200 °C, and 250 °C in order to produce activated char. Then, the char was impregnated using Phosphoric Acid activator (H3PO4) for 24 hours. Characteristics of activated carbon indicate that the treatment of char by chemical activation of oil palm fronds powder has an effect on the properties of activated carbon. The activated carbons that has the highest absorption properties to Iodine (822.91 mg/g) were obtained from the impregnation process with 15% concentration of Phosphoric Acid (H3PO4) at pyrolysis temperature of 200 °C. Furthermore, the activation process resulted in activated carbon with water content of 8%, ash content of 4%, volatile matter 39%, and fixed carbon 75%, Iodine number 822.91 mg/g.

Preparation of porous bio-char and activated carbon from rice husk by leaching ash and chemical activation.

PubMed

Ahiduzzaman, Md; Sadrul Islam, A K M

2016-01-01

Preparation porous bio-char and activated carbon from rice husk char study has been conducted in this study. Rice husk char contains high amount silica that retards the porousness of bio-char. Porousness of rice husk char could be enhanced by removing the silica from char and applying heat at high temperature. Furthermore, the char is activated by using chemical activation under high temperature. In this study no inert media is used. The study is conducted at low oxygen environment by applying biomass for consuming oxygen inside reactor and double crucible method (one crucible inside another) is applied to prevent intrusion of oxygen into the char. The study results shows that porous carbon is prepared successfully without using any inert media. The adsorption capacity of material increased due to removal of silica and due to the activation with zinc chloride compared to using raw rice husk char. The surface area of porous carbon and activated carbon are found to be 28, 331 and 645 m(2) g(-1) for raw rice husk char, silica removed rice husk char and zinc chloride activated rice husk char, respectively. It is concluded from this study that porous bio-char and activated carbon could be prepared in normal environmental conditions instead of inert media. This study shows a method and possibility of activated carbon from agro-waste, and it could be scaled up for commercial production.

Effects of rice husks and their chars from hydrothermal carbonization on the germination rate and root length of Lepidium sativum

NASA Astrophysics Data System (ADS)

Kern, Jürgen; Mukhina, Irina; Dicke, Christiane; Lanza, Giacomo; Kalderis, Dimitrios

2015-04-01

Currently, char substrates gain a lot of interest, since they are being discussed as a component in growing media, which may become one option for the replacement of peat. Among different thermal conversion processes of biomass hydrothermal carbonization (HTC) has been found to produce chars with similar acidic pH values like peat. The question however is, if these hydrochars, which may contain toxic phenolic compounds are suitable to be introduced as a new substitute for peat in horticulture. In this study rice husk were hydrothermally carbonized at 200° C for 6 hours, yielding in hydrochars containing organic contaminants such as phenols and furfurals, which may affect plants and soil organisms. We investigated potential toxic effects on the germination rate and the root length of cress salad (Lepidium sativum) in four fractions: i) soil control, ii) raw rice husk + soil, iii) unwashed rice char + soil and iv) acetone/water washed rice char + soil. It could be shown that phenols and furfurals, which were removed from the hydrochar after washing by 80 to 96% did not affect the germination rate and the root length of the cress plants. The lowest germination rate and root length were found in the soil control, the highest in the non-washed hydrochar treatment, indicating a fertilization effect and growth stimulation of cress salad by hydrochar. If this result can be confirmed for other target and non-target organisms in future studies, a new strategy for the production of growing media may be developed.

Phosphazene diamines

NASA Technical Reports Server (NTRS)

Paciorek, K. L.; Harris, D. H.; Ito, T. I.; Kratzer, R. H.

1980-01-01

The synthesis of a specific phosphazene diamine was optimized, other phosphorus-containing diamines were prepared, and their effect upon certain characteristics of epoxy resins, prepared via reaction with MY 720, in particular, char yield at elevated temperatures was evaluated. The synthesis of the phosphazene diamine resulting from the interaction of methylenedianline with 4,4'-bis(diphenylphosphino)biphenyl was simplified into a one step process giving 77 percent yield of the pure product. Using this procedure, a related diamine containing bis(diphenylphosphino)methane was obtained in a 70 percent yield. Preparation of another class of phosphorus containing amines based upon p-aminophenyldiphenyl-phosphine was unsuccessful; the inability to produce p-aminophenylithlum was responsible for this failure. Seven epoxy resins employing Araldite MY 720, diaminodiphenylsulfone, and two of the phosphorus containing diamines were prepared, characterized, and their char yield capacity at elevated temperatures assessed. Based on these investigations, the resins containing phosphorus appear to exhibit significantly better char formation characteristics than materials hardened using conventional amines, without impairing the other properties measured.

Polar and aliphatic domains regulate sorption of phthalic acid esters (PAEs) to biochars.

PubMed

Sun, Ke; Jin, Jie; Keiluweit, Marco; Kleber, Markus; Wang, Ziying; Pan, Zezhen; Xing, Baoshan

2012-08-01

Molecular variations among different biochar categories translate into differences in their ability to function as sorbents to three phthalic acid esters (PAEs) representing a gradient in hydrophobicity. The sorption capacity (K(OC)) for all three PAEs was the greatest for amorphous biochars (heat treatment temperature HTT=400 °C), followed by biochars produced at 300 °C, and was best explained by the hydrophobicity of the sorbate. Greater alkyl C content and higher polarity of grass chars versus wood chars prepared at similar temperatures explained both (a) the difference in sorbent strength between feedstocks and (b) the maximum in sorbent strength at relatively low HTTs (300-400 °C). Hydrophobic partitioning into 'soft' alkyl carbon and specific H-bonding involving char-bound O and N groups jointly account for high affinities of PAEs for low-HTT biochars. The results highlight the influence of feedstocks and HTTs on PAEs sorption strength and mechanism. Copyright © 2012 Elsevier Ltd. All rights reserved.

Burning characteristics and fiber retention of graphite/resin matrix composites

NASA Technical Reports Server (NTRS)

Bowles, K. J.

1980-01-01

Graphite fiber reinforced resin matrix composites were subjected to controlled burning conditions to determine their burning characteristics and fiber retention properties. Two types of burning equipment were used. Small samples were burned with a natural gas fired torch to study the effects of fiber orientation and structural flaws such as holes and slits that were machined into the laminates. Larger laminate samples were burned in a Heat Release Rate Calorimeter. Unidirectional epoxy/graphite and polyimide/graphite composites and boron powder filled samples of each of the two composite systems were burn tested and exposed to a thermal radiation. The effects of fiber orientation, flaws, and boron filler additives to the resins were evaluated. A high char forming polyimide resin was no more effective in retaining graphite fibers than a low char forming epoxy resin when burning in air.

Freeboard reactions in fluidized coal combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walsh, P.M.; Dutta, A.; Beer, J.M.

1984-05-11

The objective of this study was to determine the contribution of freeboard combustion to overall fixed carbon conversion during atmospheric pressure fluidized bed combustion of Kentucky No. 9 high volatile bituminous coal. The progress of the O/sub 2//char reaction in the freeboard was inferred from O/sub 2/ profiles determined by gas sampling. The rates of O/sub 2/ consumption were in good agreement with the O/sub 2//char rate expression of Sergeant and Smith (1973), except at the lowest temperature investigated (964 K). The discrepancy in this case might be due to catalysis of the O/sub 2//char reaction by lime, since thismore » was the first run of the series. Extrapolation of the O/sub 2/ profile to the bed surface using the rate expression of Sergeant and Smith showed that approximately all of the fixed carbon conversion could be accounted for by freeboard combustion. A simple model is proposed in which devolatilization, fragmentation, attrition, and volatile combustion are limited to the bed; with combustion of the finely ground char occurring only in the freeboard. This model predicts O/sub 2/ at the combustor outlet within 60% of the measured values, except in the low temperature/high lime case.« less

Changes in composition and porosity occurring during the thermal degradation of wood and wood components

USGS Publications Warehouse

Rutherford, David W.; Wershaw, Robert L.; Cox, Larry G.

2005-01-01

Samples of pine and poplar wood, pine bark, and purified cellulose and lignin were charred at temperatures ranging from 250?C to 500?C for times ranging from 1 hour to 168 hours. Changes in composition were examined by Fourier Transform Infrared (FTIR) and 13C Nuclear Magnetic Resonance (NMR) spectrometry, mass loss, and elemental composition (carbon, hydrogen, and oxygen) of the char. Structural changes were examined by changes in porosity as measured by nitrogen gas adsorption. 13C NMR spectrometry, mass loss, and elemental composition were combined to estimate the mass of aromatic and aliphatic carbon remaining in the char. Mass loss and elemental composition were combined to estimate the chemical composition of material lost for various time intervals of heating. These analyses showed that aliphatic components in the test materials were either lost or converted to aromatic carbon early in the charring process. Nitrogen adsorption showed that no porosity develops for any of the test materials with heating at 250?C, even though substantial loss of material and changes in composition occurred. Porosity development coincided with the loss of aromatic carbon, indicating that micropores were developing within a fused-ring matrix.

Co-pyrolysis behavior of fermentation residues with woody sawdust by thermogravimetric analysis and a vacuum reactor.

PubMed

Zheng, Yan; Zhang, Yimin; Xu, Jingna; Li, Xiayang; Charles Xu, Chunbao

2017-12-01

This study aimed at cost-effective utilization of fermentation residues (FR) from biogas project for bio-energy via co-pyrolysis of FR and woody sawdust (WS). In this study, a vacuum reactor was used to study the pyrolysis behaviors of individual and blend samples of FR and WS. Obvious synergistic effects were observed, resulting in a lower char yield but a higher gas yield. The presence of woody sawdust promoted the devolatilization of FR, and improved the syngas (H 2 and CO) content in the gaseous products. Compared to those of the char from pyrolysis of individual feedstock, co-pyrolysis of FR and WS in the vacuum reactor promoted the cracking reactions of large aromatic rings, enlarged the surface area and reduced the oxygenated groups of the resulted char. Copyright © 2017 Elsevier Ltd. All rights reserved.

Silicone modified resins for graphite fiber laminates

NASA Technical Reports Server (NTRS)

Frost, L. W.; Bower, G. M.

1979-01-01

The development of silicon modified resins for graphite fiber laminates which will prevent the dispersal of graphite fibers when the composites are burned is discussed. Eighty-five silicone modified resins were synthesized and evaluated including unsaturated polyesters, thermosetting methacrylates, epoxies, polyimides, and phenolics. Neat resins were judged in terms of Si content, homogeneity, hardness, Char formation, and thermal stability. Char formation was estimated by thermogravimetry to 1,000 C in air and in N2. Thermal stability was evaluated by isothermal weight loss measurements for 200 hrs in air at three temperatures. Four silicone modified epoxies were selected for evaluation in unidirectional filament wound graphite laminates. Neat samples of these resins had 1,000 C char residues of 25 to 50%. The highest flexural values measured for the laminates were a strength of 140 kpsi and a modulus of 10 Mpsi. The highest interlaminar shear strength was 5.3 kpsi.

The Effect of Polymer Char on Nitridation Kinetics of Silicon

NASA Technical Reports Server (NTRS)

Chan, Rickmond C.; Bhatt, Ramakrishna T.

1994-01-01

Effects of polymer char on nitridation kinetics of attrition milled silicon powder have been investigated from 1200 to 1350 C. Results indicate that at and above 1250 C, the silicon compacts containing 3.5 wt percent polymer char were fully converted to Si3N4 after 24 hr exposure in nitrogen. In contrast, the silicon compacts without polymer char could not be fully converted to Si3N4 at 1350 C under similar exposure conditions. At 1250 and 1350 C, the silicon compacts with polymer char showed faster nitridation kinetics than those without the polymer char. As the polymer char content is increased, the amount of SiC in the nitrided material is also increased. By adding small amounts (approx. 2.5 wt percent) of NiO, the silicon compacts containing polymer char can be completely nitrided at 1200 C. The probable mechanism for the accelerated nitridation of silicon containing polymer char is discussed.

Fracture in Phenolic Impregnated Carbon Ablator

NASA Technical Reports Server (NTRS)

Agrawal, Parul; Chavez-Garcia, Jose; Pham, John

2013-01-01

This paper describes the development of a novel technique to understand the failure mechanisms inside thermal protection materials. The focus of this research is on the class of materials known as phenolic impregnated carbon ablators. It has successfully flown on the Stardust spacecraft and is the thermal protection system material chosen for the Mars Science Laboratory and SpaceX Dragon spacecraft. Although it has good thermal properties, structurally, it is a weak material. To understand failure mechanisms in carbon ablators, fracture tests were performed on FiberForm(Registered TradeMark) (precursor), virgin, and charred ablator materials. Several samples of these materials were tested to investigate failure mechanisms at a microstructural scale. Stress-strain data were obtained simultaneously to estimate the tensile strength and toughness. It was observed that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred carbon ablators, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred carbon ablators showed greater strength values compared with FiberForm samples, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Remote Recession Sensing of Ablative Heat Shield Materials

NASA Technical Reports Server (NTRS)

Winter, Michael W.; Stackpoole, Margaret; Nawaz, Anuscheh; Gonzales, Gregory Lewis; Ho, Thanh

2014-01-01

Material recession and charring are two major processes determining the performance of ablative heat shield materials. Even in ground testing, the characterization of these two mechanisms relies on measurements of material thickness before and after testing, thus providing only information integrated over the test time. For recession measurements, optical methods such as imaging the sample surface during testing are under investigation but require high alignment and instrument effort, therefore being not established as a standard measurement method. For char depth measurements, the most common method so far consists in investigation of sectioned samples after testing or in the case of Stardust where core extractions were performed to determine char information. In flight, no reliable recession measurements are available, except total recession after recovering the heat shield on ground. Developments of mechanical recession sensors have been started but require substantial on board instrumentation adding mass and complexity. In this work, preliminary experiments to evaluate the feasibility of remote sensing of material recession and possibly char depth through optically observing the emission signatures of seeding materials in the post shock plasma is investigated. It is shown that this method can provide time resolved recession measurements without the necessity of accurate alignment procedures of the optical set-up and without any instrumentation on board of a spacecraft. Furthermore, recession data can be obtained without recovering flight hardware which would be a huge benefit for inexpensive heat shield material testing on board of small re-entry probes, e.g. on new micro-satellite re-entry probes as a possible future application of Cubesats or RBR

Effects of pressure on morphology and structure of bio-char from pressurized entrained-flow pyrolysis of microalgae.

PubMed

Maliutina, Kristina; Tahmasebi, Arash; Yu, Jianglong

2018-06-01

The present dataset describes the entrained-flow pyrolysis of Microalgae Chlorella vulgaris and the results obtained during bio-char characterization. The dataset includes a brief explanation of the experimental procedure, experimental conditions and the influence of pyrolysis conditions on bio-chars morphology and carbon structure. The data show an increase in sphericity and surface smoothness of bio-chars at higher pressures and temperatures. Data confirmed that the swelling ratio of bio-chars increased with pressure up to 2.0 MPa. Consequently, changes in carbon structure of bio-chars were investigated using Raman spectroscopy. The data showed the increase in carbon order of chars at elevated pressures. Changes in the chemical structure of bio-char as a function of pyrolysis conditions were investigated using FTIR analysis.

Mechanism of catalytic gasification of coal char. Quarterly technical report No. 5, October 1 to December 31, 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, B. J.; Sancier, K. M.; Sheridan, D. R.

1982-02-26

The purpose of this study is to determine the mechanisms involved in the catalytic reactions of coal char and to identify the specific reaction steps and the parameters that control the catalytic process. The mode of action of the catalyst can be viewed in two ways. In one view, the catalyst participates in a reduction/oxidation cycle. The initial reaction between the carbon and the catalyst reduces the KOH to potassium accompanied by the gaseous reactant (H/sub 2/O or CO/sub 2/), producing further gaseous products (CO and H/sub 2/) and regenerating the initial state of the catalyst. In an alternative view,more » the catalyst initially forms an alkali metal addition compound with the carbon network of the char. The carbon-carbon bonds are altered by the formation of the metal-carbon linkage, possibly by electron transfer from the alkali metal atom to the carbon structure. As a result, the carbon structure is more readily attacked by the gaseous reactant (CO or H/sub 2/O) to produce the products of gasification. The following areas were investigated to provide experimental evidence for these catalytic modes of action: chemical kinetic measurements; thermodynamic measurements; free radicals in reacting carbon; electrical conductivity measurements. A detailed discussion on the catalyst-carbon interaction and on the reaction intermediate is provided.« less

Structural characterization of polysaccharides from bamboo

NASA Astrophysics Data System (ADS)

Kamil, Ruzaimah Nik Mohamad; Yusuf, Nur'aini Raman; Yunus, Normawati M.; Yusup, Suzana

2014-10-01

The alkaline and water soluble polysaccharides were isolate by sequential extractions with distilled water, 60% ethanol containing 1%, 5% and 8% NaOH. The samples were prepared at 60 °C for 3 h from local bamboo. The functional group of the sample were examined using FTIR analysis. The most precipitate obtained is from using 60% ethanol containing 8% NaOH with yield of 2.6%. The former 3 residues isolated by sequential extractions with distilled water, 60% ethanol containing 1% and 5% NaOH are barely visible after filtering with cellulose filter paper. The FTIR result showed that the water-soluble polysaccharides consisted mainly of OH group, CH group, CO indicates the carbohydrate and sugar chain. The sample weight loss was slightly decreased with increasing of temperature.

Bone char effects on soil: sequential fractionations and XANES spectroscopy

NASA Astrophysics Data System (ADS)

Morshedizad, Mohsen; Panten, Kerstin; Klysubun, Wantana; Leinweber, Peter

2018-01-01

The acceptability of novel bone char fertilizers depends on their P release, but reactions at bone char surfaces and impacts on soil P speciation are insufficiently known. By using sequential fractionation and synchrotron-based X-ray absorption near-edge structure (XANES) spectroscopy we investigated whether and how the chemical composition of bone char particles has been altered in soil and has consequently affected the P speciation of amended soils. Therefore, two different kinds of bone char particles (BC produced by the pyrolysis of degreased animal bone chips at 800 °C and BCplus, a BC enriched with reduced sulfur compounds) were manually separated from the soil at the end of two different experiments: incubation leaching and ryegrass cultivation. Sequential P fractionation of amended soils showed P enrichment in all fractions compared to the control. The most P increase between all treatments significantly occurred in the NaOH-P and resin-P fractions in response to BCplus application in both incubation-leaching and ryegrass cultivation experiments. This increase in the readily available P fraction in BCplus-treated soils was confirmed by linear combination fitting (LCF) analysis on P K-edge XANES spectra of BC particles and amended soils. The proportion of Ca hydroxyapatite decreased, whereas the proportion of CaHPO4 increased in BCplus particles after amended soils had been incubated and leached and cropped by ryegrass. Based on P XANES speciation as determined by LCF analysis, the proportion of inorganic Ca(H2PO4)2 increased in amended soils after BCplus application. These results indicate that soil amendment with BCplus particles leads to elevated P concentration and maintains more soluble P species than BC particles even after 230 days of ryegrass cultivation.

Could managed burning of peatlands lead to carbon storage?

NASA Astrophysics Data System (ADS)

Clay, G.; Worrall, F.

2007-12-01

Peatlands are the UK's largest single terrestrial carbon store with carbon stored in UK peatlands than in forests of Britain and France combined. Unlike most northern peatlands in the peat soils of the UK are heavily managed for recreation and agriculture and due to their proximity to major centres of population are under more anthropogenic pressure than most peatlands. A typical management strategy on UK upland peats is the use of managed fire to restrict vegetation. Fires are used upon a 10-25 year rotation and are described as "cool" as they remove the crown of the vegetation without scorching the litter layer or the underlying soil. In this case the fire destroys primary productivity and limits litter production but produces char. Char is a low volume, highly refractory, high carbon content product while litter is a high volume, decomposable, lower carbon content product. Therefore, the question is if there are fire conditions underwhich the production of char causes more carbon to be stored in the peat than would have been stored if no fire management had been employed. This study uses detailed vegetation studies from a long term monitoring site in order to assess litter and biomass production; in laboratory experimental burns were undertaken in order to assess the amount and controls upon char production and the carbon content of that char. Results of field and laboratory observations are used to model carbon accumulation under s aseries of fire management scenarios and the modelling shows that cools burns at long rotations could lead to higher carbon storage than if no fire had occurred, further than in several cases more carbon accumulation occurred even if less depth of peat was generated.

Could managed burning of peatlands lead to enhanced carbon storage?

NASA Astrophysics Data System (ADS)

Worrall, F.; Clay, G. D.

2009-04-01

Peatlands are the UK's largest single terrestrial carbon store with carbon stored in UK peatlands than in forests of Britain and France combined. Unlike most northern peatlands in the peat soils of the UK are heavily managed for recreation and agriculture and due to their proximity to major centres of population are under more anthropogenic pressure than most peatlands. A typical management strategy on UK upland peats is the use of managed fire to restrict vegetation. Fires are used upon a 10-25 year rotation and are described as "cool" as they are designed to remove the crown of the vegetation without scorching the litter layer or the underlying soil. In this case the fire destroys primary productivity and limits litter production but produces char. Char is a low volume, highly refractory, high carbon content product while litter is a high volume, decomposable, lower carbon content product. Therefore, the question is if there are fire conditions under which the production of char causes more carbon to be stored in the peat than would have been stored if no fire management had been employed. This study combines field studies of recent managed burns and wildfires along with detailed vegetation studies from a long term monitoring site in order to assess litter, biomass and black carbon production. In the laboratory experimental burns were undertaken in order to assess the amount and controls upon char production and the carbon content of that char. Results of field and laboratory observations are used to model carbon accumulation under a series of fire management scenarios and the modelling shows that cools burns at long rotations could lead to higher carbon storage than if no fire had occurred, further in several cases more carbon accumulation occurred even if less depth of peat was generated.

Method and apparatus for acoustically monitoring the flow of suspended solid particulate matter. [Patent application; monitoring char flow in coal gasifier

DOEpatents

Roach, P.D.; Raptis, A.C.

1980-11-24

A method and apparatus for monitoring char flow in a coal gasifier system includes flow monitor circuits which measure acoustic attenuation caused by the presence of char in a char line and provides a char flow/no flow indication and an indication of relative char density. The flow monitor circuits compute the ratio of signals in two frequency bands, a first frequency band representative of background noise, and a second higher frequency band in which background noise is attenuated by the presence of char. Since the second frequency band contains higher frequencies, the ratio can be used to provide a flow/no flow indication. The second band can also be selected so that attenuation is monotonically related to particle concentration, providing a quantitative measure of char concentration.

Removal of elemental Mercury from flue gas using wheat straw chars modified by K2FeO4 reagent.

PubMed

Zhou, Jianfei; Liu, Yangxian; Pan, Jianfeng

2017-12-01

In this article, wheat straw (WS) char, a common agricultural waste and renewable biomass, was pyrolyzed and then modified by K 2 FeO 4 reagent to develop an efficient sorbent for removal of Hg 0 from flue gas. Brunauer-Emmett-Teller, scanning electron microscopy with energy spectrum and X-ray diffraction (XRD) were employed to characterize the sorbents. The effects of K 2 FeO 4 loading, reaction temperature, Hg 0 inlet concentration and concentrations of gas mixtures O 2 , NO and SO 2 in flue gas on Hg 0 removal were investigated in a fixed-bed reactor. The results show that K 2 FeO 4 -impregnation can improve pore structure of WS char and produce new active sites, which significantly enhance Hg 0 removal. Increasing Hg 0 inlet concentration significantly decreases Hg 0 removal efficiency. O 2 in flue gas promotes Hg 0 oxidation by replenishing the oxygen groups on the surface of modified chars. The presence of NO obviously promotes Hg 0 removal since it can oxidize Hg 0 to Hg(NO 3 ) 2 . SO 2 in flue gas significantly decreases Hg 0 removal efficiency due to the competition adsorption between SO 2 and Hg 0 . The increase in reaction temperature has a dual impact on Hg 0 removal.

Tracking the conversion of nitrogen during pyrolysis of antibiotic mycelial fermentation residues using XPS and TG-FTIR-MS technology.

PubMed

Zhu, Xiangdong; Yang, Shijun; Wang, Liang; Liu, Yuchen; Qian, Feng; Yao, Wenqing; Zhang, Shicheng; Chen, Jianmin

2016-04-01

Antibiotic mycelial fermentation residues (AMFRs), which are emerging solid pollutants, have been recognized as hazardous waste in China since 2008. Nitrogen (N), which is an environmental sensitivity element, is largely retained in AMFR samples derived from fermentation substrates. Pyrolysis is a promising technology for the treatment of solid waste. However, the outcomes of N element during the pyrolysis of AMFRs are still unknown. In this study, the conversion of N element during the pyrolysis of AMFRs was tracked using XPS (X-ray photoelectron spectroscopy) and online TG-FTIR-MS (Thermogravimetry-Fourier transform infrared-Mass spectrometry) technology. In the AMFR sample, organic amine-N, pyrrolic-N, protein-N, pyridinic-N, was the main N-containing species. XPS results indicated that pyrrolic-N and pyridinic-N were retained in the AMFR-derived pyrolysis char. More stable species, such as N-oxide and quaternary-N, were also produced in the char. TG-FTIR-MS results indicated that NH3 and HCN were the main gaseous species, and their contents were closely related to the contents of amine-N and protein-N, and pyrrolic-N and pyridinic-N of AMFRs, respectively. Increases in heating rate enhanced the amounts of NH3 and HCN, but had less of an effect on the degradation degree of AMFRs. N-containing organic compounds, including amine-N, nitrile-N and heterocyclic-N, were discerned from the AMFR pyrolysis process. Their release range was extended with increasing of heating rate and carbon content of AMFR sample. This work will help to take appropriate measure to reduce secondary pollution from the treatment of AMFRs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Molecular aspects of aromatic C additions to soils: Implications of char quality for ecosystem functionality

NASA Astrophysics Data System (ADS)

Keiluweit, M.; Nico, P. S.; Johnson, M. G.; Kleber, M.

2009-12-01

Solid residues of incomplete combustion (biochar or char) are continuously being added to soils due to natural vegetation fires in many ecosystems. However, new strategies for carbon sequestration in soils are likely to include the active addition of biochar to soils. Since biochar is a highly aromatic organic material such additions will modify the native molecular structure of soil organic matter and thus alter interactions with the global atmosphere and hydrosphere. Here we present a molecular level assessment of the physical organization and chemical complexity of biomass-derived chars and, specifically, that of aromatic carbon in char structures. Differences among wood and grass charred at temperatures from 100 to 700°C are investigated. BET-N2 surface area, X-ray diffraction (XRD), synchrotron-based Near-edge X-ray Absorption Fine Structure (NEXAFS) and Fourier transform infrared (FT-IR) spectroscopy results demonstrate how the two plant precursor materials undergo analogous, but quantitatively different physical-chemical transitions as charring intensity increases. These changes suggest the existence of four distinct physical and chemical categories of char. We find that each category of char consists of a unique mixture of chemical phases and physical states: (i) in transition chars the crystalline character of the precursor materials is preserved, (ii) in amorphous chars the heat-altered molecules and incipient aromatic polycondensates are randomly mixed, (iii) composite chars consist of poorly ordered graphene stacks embedded in amorphous phases, and (iv) turbostratic chars are dominated by turbostratic (disordered) graphitic crystallites. There is wide variation in both the chemical and the physical nature of aromatic carbon among these char categories. In this presentation we will point out how molecular variations among the aromatic components of the different char categories translate into differences in their ability to: (i) persist in the environment, (ii) function as environmental sorbents, and (iii) to enable the soil to provide environmental services.

Mapping soil organic carbon content and composition across Australia to assess vulnerability to climate change

NASA Astrophysics Data System (ADS)

Viscarra Rossel, R. A.

2015-12-01

We can effectively monitor soil condition—and develop sound policies to offset the emissions of greenhouse gases—only with accurate data from which to define baselines. Currently, estimates of soil organic C for countries or continents are either unavailable or largely uncertain because they are derived from sparse data, with large gaps over many areas of the Earth. Here, we derive spatially explicit estimates, and their uncertainty, of the distribution and stock of organic C content and composition in the soil of Australia. The composition of soil organic C may be characterized by chemical separation or physical fractionation based on either particle size or particle density (Skjemstad et al., 2004; Gregorich et al., 2006; Kelleher&Simpson, 2006; Zimmermann et al., 2007). In Australia, for example, Skjemstad et al. (2004) used physical separation of soil samples into 50-2000 and <50-μm particle-size fractions followed by the measurement of char-carbon using solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, giving the three OC pools, particulate organic carbon (POC), humic organic carbon (HOC) and resistant organic carbon (ROC; charcoal or char-carbon). We assembled and harmonized data from several sources to produce the most comprehensive set of data on the current stock of organic C in soil of the continent. Using them, we have produced a fine spatial resolution baseline map of organic C, POC, HOC and ROC at the continental scale. In this presentation I will describe how we made the maps and how we use them to assess the vulnerability of soil organic C to for instance climate change.

Effect of high-pressure on pine sawdust pyrolysis: Products distribution and characteristics

NASA Astrophysics Data System (ADS)

Xu, Baiqing; Li, Aimin

2017-08-01

In this work, the pressurized pyrolysis of pine sawdust was performed with a self-made pressurized pyrolysis reactor to investigatethe influence of pyrolysis pressure in the range of 0-5 MPa on products distribution and characteristics. The combustion feature and microstructure of bio-char had analyzed by thermogravimetric (TG) and scanning electron microscopy (SEM), respectively. Elemental analyzer and Fourier transform infrared spectroscopy (FTIR) were used to confirm the identities of bio-oil. The results indicated the pressure had a notable impact on the biomass pyrolysis, which promoted the secondary cracking of bio-oil to produce more gaseous products and bio-char. The minimum bio-oil yield of 20.24% was obtained at the pressure of 5 MPa. Furthermore, the pressure improved the products characteristics. The increasing of pressure was favour to the deoxygenation and dehydrogenation reactions of bio-oil, which led to the increase of CH4, H2 and CO2 in gas. At the same time, under the influence of pressure, the surface structure and compactedness of the bio-char were obviously improved.

Flame Suppression of Cotton with Polymer-Clay Thin Film Assemblies

NASA Astrophysics Data System (ADS)

Sukhonosova, Galina; Li, Yu-Chin; Grunlan, Jaime

2010-03-01

Cotton fabric was treated with flame-retardant coatings composed of branched polyethylenimine (PEI) and montmorillonite (MMT), prepared via layer-by-layer (LbL) assembly. Four coatings were created with solutions of BPEI (pH 7 or 10) and MMT (0.2 or 1 wt. %). The thickness and composition of the coatings were studied by ellipsometry and quartz crystal microbalance. PEI at pH 10 produces the thickest films. Each coating recipe was evaluated at 5 and 20 bilayers. Thermogravimetric analysis showed that coated fabrics left 13 % char after heating at 500 C, over an order of magnitude more char than from uncoated fabric, with less than 4% coming from the coating itself. Coating reduced afterglow time by 9 seconds in vertical flame tests. Post-burn chars of coated fabrics were examined by scanning electron microscopy, revealing that weave structure and fiber shape in all coated fabrics were preserved through burning. This is the first study of its kind to use layer-by-layer assembly to generate a flame retardant coating on a complex substrate like cotton fabric.

Dynamic molecular structure of plant biomass-derived black carbon (biochar)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keiluweit, M.; Nico, P.S.; Johnson, M.G.

2009-11-15

Char black carbon (BC), the solid residue of incomplete combustion, is continuously being added to soils and sediments due to natural vegetation fires, anthropogenic pollution, and new strategies for carbon sequestration ('biochar'). Here we present a molecular-level assessment of the physical organization and chemical complexity of biomass-derived chars and, specifically, that of aromatic carbon in char structures. BET-N{sub 2} surface area, X-ray diffraction (XRD), synchrotron-based Near-edge X-ray Absorption Fine Structure (NEXAFS), and Fourier transform infrared (FT-IR) spectroscopy are used to show how two plant materials (wood and grass) undergo analogous, but quantitatively different physical-chemical transitions as charring temperature increases frommore » 100 to 700 C. These changes suggest the existence of four distinct categories of char consisting of a unique mixture of chemical phases and physical states: (i) in transition chars the crystalline character of the precursor materials is preserved, (ii) in amorphous chars the heat-altered molecules and incipient aromatic polycondensates are randomly mixed, (iii) composite chars consist of poorly ordered graphene stacks embedded in amorphous phases, and (iv) turbostratic chars are dominated by disordered graphitic crystallites. The molecular variations among the different char categories translate into differences in their ability to persist in the environment and function as environmental sorbents.« less

BC measurement activities at the U.S. Environmental Protection Agency

EPA Science Inventory

Black carbon (BC)--sometimes referred to as soot, char, or elemental carbon (EC)--is a refractory form of light-absorbing carbon produced from incomplete combustion. Accurate measurement of BC in combustion source emissions is important for understanding anthropogenic climate for...

Ferns and fires: Experimental charring of ferns compared to wood and implications for paleobiology, paleoecology, coal petrology, and isotope geochemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

McParland, L.C.; Collinson, M.E.; Scott, A.C.

We report the effects of charring on the ferns Osmunda, Pteridium, and Matteucia with coniferous wood (Sequoia) for comparison. Like charred wood, charred ferns shrink, become black and brittle with a silky sheen, and retain three-dimensional cellular structure. Ferns yield recognizable charcoal (up to 800{sup o}C) that could potentially survive in the fossil record enabling reconstruction of ancient fire-prone vegetation containing ferns. Charred fossils of herbaceous ferns would indicate surface fires. Like charred wood, cell-wall layers of charred ferns homogenize, and their reflectance values increase with rising temperature. Charcoalified fragments of thick-walled cells from conifer wood or fern tissues aremore » indistinguishable and so cannot be used to infer the nature of source vegetation. Charred conifer wood and charred fern tissues show a relationship between mean random reflectance and temperature of formation and can be used to determine minimum ancient fire temperatures. Charred fern tissues consistently have significantly more depleted {delta}{sup 13}C values ({le} 4 parts per thousand) than charred wood. Therefore, if an analysis of {delta} {sup 13}C through time included fern charcoal among a succession of wood charcoals, any related shifts in {delta} {sup 13}C could be misinterpreted as atmospheric changes or misused as isotope stratigraphic markers. Thus, charcoals of comparable botanical origin and temperatures of formation should be used in order to avoid misinterpretations of shifts in {delta}{sup 13}C values.« less

Design of a Decentralized Asynchronous Membership Protocol and an Implementation of Its Communications Layer

DTIC Science & Technology

1993-03-01

sstm[MAXFD], stpm [MAXFD]; u-short fport,bport; char sfport[MLAXPORTI, sbport[MAXPORTII; int childpid; char my~name[MAXHOSTNAME+ 1 ], *ip~add&, char my...34, "tpm", stpm , (char*) NULL); printf ("Error executing tpm\

Particle behavior and char burnout mechanisms under pressurized combustion conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, C.M.; Spliethoff, H.; Hein, K.R.G.

Combined cycle systems with coal-fired gas turbines promise highest cycle efficiencies for this fuel. Pressurized pulverized coal combustion, in particular, yields high cycle efficiencies due to the high flue gas temperatures possible. The main problem, however, is to ensure a flue gas clean enough to meet the high gas turbine standards with a dirty fuel like coal. On the one hand, a profound knowledge of the basic chemical and physical processes during fuel conversion under elevated pressures is required whereas on the other hand suitable hot gas cleaning systems need to be developed. The objective of this work was tomore » provide experimental data to enable a detailed description of pressurized coal combustion processes. A series of experiments were performed with two German hvb coals, Ensdorf and Goettelborn, and one German brown coal, Garzweiler, using a semi-technical scale pressurized entrained flow reactor. The parameters varied in the experiments were pressure, gas temperature and bulk gas oxygen concentration. A two-color pyrometer was used for in-situ determination of particle surface temperatures and particle sizes. Flue gas composition was measured and solid residue samples taken and subsequently analyzed. The char burnout reaction rates were determinated varying the parameters pressure, gas temperature and initial oxygen concentration. Variation of residence time was achieved by taking the samples at different points along the reaction zone. The most influential parameters on char burnout reaction rates were found to be oxygen partial pressure and fuel volatile content. With increasing pressure the burn-out reactions are accelerated and are mostly controlled by product desorption and pore diffusion being the limiting processes. The char burnout process is enhanced by a higher fuel volatile content.« less

Method and apparatus for acoustically monitoring the flow of suspended solid particulate matter

DOEpatents

Roach, Paul D.; Raptis, Apostolos C.

1982-01-01

A method and apparatus for monitoring char flow in a coal gasifier system cludes flow monitor circuits which measure acoustic attenuation caused by the presence of char in a char line and provide a char flow/no flow indication and an indication of relative char density. The flow monitor circuits compute the ratio of signals in two frequency bands, a first frequency band representative of background noise, and a second higher frequency band in which background noise is attenuated by the presence of char. Since the second frequency band contains higher frequencies, the ratio can be used to provide a flow/no flow indication. The second band can also be selected so that attenuation is monotonically related to particle concentration, providing a quantitative measure of char concentration.

Effect of reactivity loss on apparent reaction order of burning char particles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, Jeffrey J.; Shaddix, Christopher R.

Considerable debate still exists in the char combustion community over the expected and observed reaction orders of carbon reacting with oxygen. In particular, very low values of the reaction order (approaching zero) are commonly observed in char combustion experiments. These observations appear to conflict with porous catalyst theory as first expressed by Thiele, which suggests that the apparent reaction order must be greater than 0.5. In this work, we propose that this conflict may be resolved by considering the decrease in char reactivity with burnout due to ash effects, thermal annealing, or other phenomena. Specifically, the influence of ash dilutionmore » of the available surface area on the apparent reaction order is explored. Equations describing the ash dilution effect are combined with a model for particle burnout based on single-film nth-order Arrhenius char combustion and yield an analytical expression for the effective reaction order. When this expression is applied for experimental conditions reflecting combustion of individual pulverized coal particles in an entrained flow reactor, the apparent reaction order is shown to be lower than the inherent char matrix reaction order, even for negligible extents of char conversion. As char conversion proceeds and approaches completion, the apparent reaction order drops precipitously past zero to negative values. Conversely, the inclusion of the ash dilution model has little effect on the char conversion profile or char particle temperature until significant burnout has occurred. Taken together, these results suggest that the common experimental observation of low apparent reaction orders during char combustion is a consequence of the lack of explicit modeling of the decrease in char reactivity with burnout. (author)« less

Co-gasification of bituminous coal and hydrochar derived from municipal solid waste: Reactivity and synergy.

PubMed

Wei, Juntao; Guo, Qinghua; He, Qing; Ding, Lu; Yoshikawa, Kunio; Yu, Guangsuo

2017-09-01

In this work, the influences of gasification temperature and blended ratio on co-gasification reactivity and synergy of Shenfu bituminous coal (SF) and municipal solid waste-derived hydrochar (HTC) were investigated using TGA. Additionally, active alkaline and alkaline earth metal (AAEM) transformation during co-gasification was quantitatively analyzed by inductively coupled plasma optical emission spectrometer for correlating synergy on co-gasification reactivity. The results showed that higher char gasification reactivity existed at higher HTC char proportion and gasification temperature, and the main synergy behaviour on co-gasification reactivity was performed as synergistic effect. Enhanced synergistic effect at lower temperature was mainly resulted from more obviously inhibiting the primary AAEM (i.e. active Ca) transformation, and weak synergistic effect still existed at higher temperature since more active K with prominent catalysis was retained. Furthermore, more active HTC-derived AAEM remaining in SF sample during co-gasification would lead to enhanced synergistic effect as HTC char proportion increased. Copyright © 2017 Elsevier Ltd. All rights reserved.

OXIDATION AND DEVOLATILIZATION OF NITROGEN IN COAL CHAR

EPA Science Inventory

The reactions of organically-bound nitrogen in coal char during combustion have been studied in a laboratory furnace using size-graded char particles prepared by the pyrolysis of a Montana lignite. The time-resolved variations of nitrogen-to-carbon ratio during char oxidation hav...

Properties of gasification-derived char and its utilization for catalytic tar reforming

NASA Astrophysics Data System (ADS)

Qian, Kezhen

Char is a low-value byproduct of biomass gasification and pyrolysis with many potential applications, such as soil amendment and the synthesis of activated carbon. The overall goal of the proposed research was to develop novel methods to use char derived from gasification for high-value applications in syngas conditioning. The first objective was to investigate effects of gasification condition and feedstock on properties of char derived from fluidized bed gasification. Results show that the surface areas of most of the char were 1--10 m 2/g and increased as the equivalence ratio increased. Char moisture and fixed carbon contents decreased while ash content increased as equivalence ratio increased. The next objective was to study the properties of sorghum and red cedar char derived from downdraft gasifier. Red cedar char contained more aliphatic carbon and o-alkyl carbon than sorghum char. Char derived from downdraft gasification had higher heating values and lower ash contents than char derived from fluidized bed gasification. The gasification reactivity of red cedar char was higher than that of sorghum char. Then, red cedar char based catalysts were developed with different preparation method to reform toluene and naphthalene as model tars. The catalyst prepared with nickel nitrate was found to be better than that with nickel acetate. The nickel particle size of catalyst impregnated with nickel nitrate was smaller than that of catalyst impregnated with nickel acetate. The particle size of catalyst impregnated with nickel acetate decreased by hydrazine reduction. The catalyst impregnated with nickel nitrate had the highest toluene removal efficiency, which was 70%--100% at 600--800 °C. The presence of naphthalene in tar reduced the catalyst efficiency. The toluene conversion was 36--99% and the naphthalene conversion was 37%--93% at 700--900 °C. Finally, effects of atmosphere and pressure on catalytic reforming of lignin-derived tars over the developed catalyst were investigated. An increase in reaction temperature led to an increase in removal of most tar components except naphthalene. High pressure promoted the catalytic conditioning of lignin tar. Hydrogen promoted the conversion of lignin into non-condensable gas.

Overview of the CHarring Ablator Response (CHAR) Code

NASA Technical Reports Server (NTRS)

Amar, Adam J.; Oliver, A. Brandon; Kirk, Benjamin S.; Salazar, Giovanni; Droba, Justin

2016-01-01

An overview of the capabilities of the CHarring Ablator Response (CHAR) code is presented. CHAR is a one-, two-, and three-dimensional unstructured continuous Galerkin finite-element heat conduction and ablation solver with both direct and inverse modes. Additionally, CHAR includes a coupled linear thermoelastic solver for determination of internal stresses induced from the temperature field and surface loading. Background on the development process, governing equations, material models, discretization techniques, and numerical methods is provided. Special focus is put on the available boundary conditions including thermochemical ablation and contact interfaces, and example simulations are included. Finally, a discussion of ongoing development efforts is presented.

Overview of the CHarring Ablator Response (CHAR) Code

NASA Technical Reports Server (NTRS)

Amar, Adam J.; Oliver, A. Brandon; Kirk, Benjamin S.; Salazar, Giovanni; Droba, Justin

2016-01-01

An overview of the capabilities of the CHarring Ablator Response (CHAR) code is presented. CHAR is a one-, two-, and three-dimensional unstructured continuous Galerkin finite-element heat conduction and ablation solver with both direct and inverse modes. Additionally, CHAR includes a coupled linear thermoelastic solver for determination of internal stresses induced from the temperature field and surface loading. Background on the development process, governing equations, material models, discretization techniques, and numerical methods is provided. Special focus is put on the available boundary conditions including thermochemical ablation, surface-to-surface radiation exchange, and flowfield coupling. Finally, a discussion of ongoing development efforts is presented.

Mercury adsorption of modified mulberry twig chars in a simulated flue gas.

PubMed

Shu, Tong; Lu, Ping; He, Nan

2013-05-01

Mulberry twig chars were prepared by pyrolysis, steam activation and impregnation with H2O2, ZnCl2 and NaCl. Textural characteristics and surface functional groups were performed using nitrogen adsorption and FTIR, respectively. Mercury adsorption of different modified MT chars was investigated in a quartz fixed-bed absorber. The results indicated that steam activation and H2O2-impregnation can improve pore structure significantly and H2O2-impregnation and chloride-impregnation promote surface functional groups. However, chloride-impregnation has adverse effect on pore structure. Mercury adsorption capacities of impregnated MT chars with 10% or 30% H2O2 are 2.02 and 1.77 times of steam activated MT char, respectively. Mercury adsorption capacity of ZnCl2-impregnated MT char increase with increasing ZnCl2 content and is better than that of NaCl-impregnated MT char at the same chloride content. The modified MT char (MT873-A-Z5) prepared by steam activation following impregnation with 5% ZnCl2 exhibits a higher mercury adsorption capacity (29.55 μg g(-1)) than any other MT chars. Copyright © 2013 Elsevier Ltd. All rights reserved.

The combustion of large particles of char in bubbling fluidized beds: The dependence of Sherwood number and the rate of burning on particle diameter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dennis, J.S.; Hayhurst, A.N.; Scott, S.A.

Particles of char derived from a variety of fuels (e.g., biomass, sewage sludge, coal, or graphite), with diameters in excess of {approx}1.5mm, burn in fluidized bed combustors containing smaller particles of, e.g., sand, such that the rate is controlled by the diffusion both of O{sub 2} to the burning solid and of the products CO and CO{sub 2} away from it into the particulate phase. It is therefore important to characterize these mass transfer processes accurately. Measurements of the burning rate of char particles made from sewage sludge suggest that the Sherwood number, Sh, increases linearly with the diameter ofmore » the fuel particle, d{sub char} (for d{sub char}>{approx}1.5mm). This linear dependence of Sh on d{sub char} is expected from the basic equation Sh=2{epsilon}{sub mf}(1+d{sub char}/2{delta}{sub diff})/{tau}, provided the thickness of the boundary layer for mass transfer, {delta}{sub diff}, is constant in the region of interest (d{sub char}>{approx}1.5mm). Such a dependence is not seen in the empirical equations currently used and based on the Frossling expression. It is found here that for chars made from sewage sludge (for d{sub char}>{approx}1.5mm), the thickness of the boundary layer for mass transfer in a fluidized bed, {delta}{sub diff}, is less than that predicted by empirical correlations based on the Frossling expression. In fact, {delta}{sub diff} is not more than the diameter of the fluidized sand particles. Finally, the experiments in this study indicate that models based on surface renewal theory should be rejected for a fluidized bed, because they give unrealistically short contact times for packets of fluidized particles at the surface of a burning sphere. The result is the new correlation Sh = 2{epsilon}{sub mf}/{tau} + (A{sub cush}/A{sub char})(d{sub char}/ {delta}{sub diff}) for the dependence of Sh on d{sub char}, the diameter of a burning char particle. This equation is based on there being a gas-cushion of fluidizing gas underneath a burning char particle; the implication of this correlation is that a completely new picture emerges for the combustion of a char particle in a hot fluidized bed. (author)« less

Removal of fluoride ion by bone char produced from animal biomass.

PubMed

Kawasaki, Naohito; Ogata, Fumihiko; Tominaga, Hisato; Yamaguchi, Isao

2009-01-01

Bone char (BC) was prepared by carbonizing four types of animal biomass, and the adsorption of fluoride ions and elution of phosphate ions were investigated. It was found that the BC yield decreased as carbonization temperature increased, and that carbonization temperature had no significant effect on surface pH, base or acid consumptions. Fluoride ion adsorption was increased in BC produced at a low carbonization temperature. The adsorption mechanism of fluoride ion on BCs might be monolayer adsorption. BC can potentially be used to remove fluoride ions in drinking water. However, it was found that phosphate ions from BC are eluted due to adsorption of fluoride ions, and that ingestion of large amounts of phosphate ions inhibits reabsorption of calcium in the human body. Thus there is a need to study the elution behavior of phosphate ions. The adsorption mechanisms of fluoride ions onto BC would be a physical adsorption onto BC and phosphate ion in BC is exchanged to fluoride ion.

Catalytic pyrolysis of Alcea pallida stems in a fixed-bed reactor for production of liquid bio-fuels.

PubMed

Aysu, Tevfik

2015-09-01

Pyrolysis of Alcea pallida stems was performed in a fixed-bed tubular reactor with and without catalyst at three different temperatures. The effects of pyrolysis parameters including temperature and catalyst on the product yields were investigated. It was found that higher temperature resulted in lower liquid (bio-oil) and solid (bio-char) yields and higher gas yields. Catalysts had different effects on product yields and composition of bio-oils. Liquid yields were increased in the presence of zinc chloride and alumina but decreased with calcium hydroxide, tincal and ulexite. The highest bio-oil yield (39.35%) by weight including aqueous phase was produced with alumina catalyst at 500 °C. The yields of bio-char, bio-oil and gas produced, as well as the compositions of the resulting bio-oils were determined by elemental analysis, TGA, FT-IR and GC-MS. 160 different compounds were identified by GC-MS in the bio-oils obtained at 500 °C. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fluidized bed selective pyrolysis of coal

DOEpatents

Shang, J.Y.; Cha, C.Y.; Merriam, N.W.

1992-12-15

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyses the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step. 9 figs.

Fluidized bed selective pyrolysis of coal

DOEpatents

Shang, Jer Y.; Cha, Chang Y.; Merriam, Norman W.

1992-01-01

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyzes the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step.

Influence of pressure on pyrolysis of black liquor: 1. Swelling.

PubMed

Whitty, Kevin; Backman, Rainer; Hupa, Mikko

2008-02-01

This is the first of two papers concerning the behavior of black liquor during pyrolysis under pressurized conditions. Two industrial kraft liquors were pyrolyzed in a laboratory-scale pressurized single particle reactor and a pressurized grid heater at temperatures ranging from 650 to 1100 degrees C and at pressures between 1 and 20 bar. The dimensions of the chars produced were measured and the specific swollen volume was calculated. Swelling decreased roughly logarithmically over the pressure range 1-20 r. An expression is developed to predict the specific swollen volume at elevated pressure when the volume at 1 bar is known. The bulk density of the char increased with pressure, indicating that liquors will be entrained less easily at higher pressures.

Sustainable development of tyre char-based activated carbons with different textural properties for value-added applications.

PubMed

Hadi, Pejman; Yeung, Kit Ying; Guo, Jiaxin; Wang, Huaimin; McKay, Gordon

2016-04-01

This paper aims at the sustainable development of activated carbons for value-added applications from the waste tyre pyrolysis product, tyre char, in order to make pyrolysis economically favorable. Two activation process parameters, activation temperature (900, 925, 950 and 975 °C) and residence time (2, 4 and 6 h) with steam as the activating agent have been investigated. The textural properties of the produced tyre char activated carbons have been characterized by nitrogen adsorption-desorption experiments at -196 °C. The activation process has resulted in the production of mesoporous activated carbons confirmed by the existence of hysteresis loops in the N2 adsorption-desorption curves and the pore size distribution curves obtained from BJH method. The BET surface area, total pore volume and mesopore volume of the activated carbons from tyre char have been improved to 732 m(2)/g, 0.91 cm(3)/g and 0.89 cm(3)/g, respectively. It has been observed that the BET surface area, mesopore volume and total pore volume increased linearly with burnoff during activation in the range of experimental parameters studied. Thus, yield-normalized surface area, defined as the surface area of the activated carbon per gram of the precursor, has been introduced to optimize the activation conditions. Accordingly, the optimized activation conditions have been demonstrated as an activation temperature of 975 °C and an activation time of 4 h. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pyrolysis of waste tyres: A review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Paul T., E-mail: p.t.williams@leeds.ac.uk

2013-08-15

Graphical abstract: - Highlights: • Pyrolysis of waste tyres produces oil, gas and char, and recovered steel. • Batch, screw kiln, rotary kiln, vacuum and fluidised-bed are main reactor types. • Product yields are influenced by reactor type, temperature and heating rate. • Pyrolysis oils are complex and can be used as chemical feedstock or fuel. • Research into higher value products from the tyre pyrolysis process is reviewed. - Abstract: Approximately 1.5 billion tyres are produced each year which will eventually enter the waste stream representing a major potential waste and environmental problem. However, there is growing interest inmore » pyrolysis as a technology to treat tyres to produce valuable oil, char and gas products. The most common reactors used are fixed-bed (batch), screw kiln, rotary kiln, vacuum and fluidised-bed. The key influence on the product yield, and gas and oil composition, is the type of reactor used which in turn determines the temperature and heating rate. Tyre pyrolysis oil is chemically very complex containing aliphatic, aromatic, hetero-atom and polar fractions. The fuel characteristics of the tyre oil shows that it is similar to a gas oil or light fuel oil and has been successfully combusted in test furnaces and engines. The main gases produced from the pyrolysis of waste tyres are H{sub 2}, C{sub 1}–C{sub 4} hydrocarbons, CO{sub 2}, CO and H{sub 2}S. Upgrading tyre pyrolysis products to high value products has concentrated on char upgrading to higher quality carbon black and to activated carbon. The use of catalysts to upgrade the oil to a aromatic-rich chemical feedstock or the production of hydrogen from waste tyres has also been reported. Examples of commercial and semi-commercial scale tyre pyrolysis systems show that small scale batch reactors and continuous rotary kiln reactors have been developed to commercial scale.« less

Characterization of black carbon and organic contaminants in wood ash from different feedstocks and types of furnaces

NASA Astrophysics Data System (ADS)

Merino, Agustin; Rey-Salgueiro, Ledicia; Omil, Beatriz; Martinez-Carballo, Elena; Simal-Gandara, Jesus

2015-04-01

Due to their important concentration of nutrient and charcoal, wood ash from biomass power plants (WA) can be used as a fertilizer and organic amendment in intensively managed soils. Unlike biochar produced in under anoxic conditions, the nature of the organic compounds present in wood ash has been scarcely studied. Due to the incomplete combustion, wood ash may contain a wide range of organic compounds, from charred to highly condensed refractory biomass, which determines the possibilities of WA as an organic amendment. In addition, the possible environmental risk of this practice must be assessed by determining the content of water-soluble and insoluble organic contaminants. due to the incomplete combustion of organic matter, organic pollutants, such as Polycyclic Aromatic Hydrocarbons (PAHs), can be formed and can remain in the combustion residue. Also, the four alkyl benzene volatile organic compounds (benzene, toluene, ethylbenzene, and the ortho, para, and meta xylenes) can be formed, depending on certain conditions during combustion. For this study 15 biomass power stations in Spain were selected. In all of them the feedstock is pine or eucalyptus branches and bark. Nine of them were bottom wood ash generated from wood fires furnaces, obtained from grate-fired or water-tube boilers. Whereas four of them were fly ash, obtained in cyclone separators. The samples were collected following a common procedure to ensure the representiveness of the sampling. Bottom ash samples were fraccionated in three fractions: < 2mm, 2-5 mm and > 5mm. Each fraction was characterized for organic matter and BTEX, styrene and total petroleum hydrocarbons Polycyclic Aromatic Hydrocarbons. For each analyzes, three replicates were analyzed per sample. Mixes wood ash shows higher amounts of charred material than fly ash. The 13 C CPMAS NMR, DSC/TG and FTIR analysis showed the loss of carbohydrates and aliphatic constituents and revealed the formation of aromatic compounds. The atomic H/C ratios, NMR spectra, DSC and FTIR confirmed the presence of condensed structures, specially in the coarse particles. However, the different wood ash showed an important range of properties revealing the presence from charred material to charcoal containing condensed structures (H/C ratios lower than 0.6; aromaticity higher than 80 % and T50-DSC higher than 500 °C). Typical organic pollutants including those water-soluble such as BTEX plus styrene, but also those water-insoluble such as polycyclic aromatic hydrocarbons (PAHs), together with aliphatic hydrocarbons, were examined in the ash. Their contents were related to degree of combustion of the biomass, determined through the content and composition of the organic matter in the wood ash. The sum of BTEX plus styrene varied from non-detected to 30 mg/kg, and the total amounts of PAHs (total PAHs) ranged between non-detected and 422 µg/kg, not exceeding the regulated limits. This research provides basic information for the evaluation of the environmental risk and potential uses of WW incinerator bottom ash The results demonstrate the important variability in the charred material properties of the different power plants and size-particles. The organic compounds contents are also variable, but in all cases were levels of pollutants in all the samples were below the limits for both soil and industrial use (Environmental Protection Agency in the European Union and the USA.

47 CFR 15.122 - Closed caption decoder requirements for digital television receivers and converter boxes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... code 0×2D Lower-left border (⌊), G2 char code 0×7C G0 dash (-), char code 0×2D Horizontal border... (-), char code 0×2D Upper-left border (⌈), G2 char code 0×7F G0 dash (-), char code 0×2D (4) Support for..., if the character to the left of the embedded return is a hyphen, the embedded return should be...

47 CFR 15.122 - Closed caption decoder requirements for digital television receivers and converter boxes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... code 0×2D Lower-left border (⌊), G2 char code 0×7C G0 dash (-), char code 0×2D Horizontal border... (-), char code 0×2D Upper-left border (⌈), G2 char code 0×7F G0 dash (-), char code 0×2D (4) Support for..., if the character to the left of the embedded return is a hyphen, the embedded return should be...

Mössbauer spectroscopic investigation of iron species in coal

USGS Publications Warehouse

Smith, Gerard V.; Liu, Juei-Ho; Saporoschenko, Mykola

1978-01-01

A series of Herrin No. 6 coal and three coal-derived samples have been examined by Mo??ssbauer spectroscopy. It is established that Mo??ssbauer spectroscopy can be used to identify multiple iron species in a whole coal or an autoclaved char sample without the need to concentrate the minerals to enhance resolution. Our results indicate that there may be an association between the pyrite in raw coal and the coal matrix. This association appears to be broken down when the coal is heated to temperatures as low as 175 ??C. It is also apparent that the iron sulphide present in the whole coal is converted to pyrite at these low temperatures. For our samples, the total quantity of iron species in different coal lithotypes is about the same, but they differ in their distributions. The fusain has the least amount of Fe2+ species when compared to the vitrain or whole-coal sample used. At least two types of nonstoichiometric pyrrhotite are produced in the heat-treated samples. One of these pyrrhotites is unstable and contains dissolved sulphur which is apparently liberated as the temperature is increased. ?? 1978.

Fast Pyrolysis of Poplar Using a Captive Sample Reactor: Effects of Inorganic Salts on Primary Pyrolysis Products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mukarakate, C.; Robichaud, D.; Donohoe, B.

2012-01-01

We have constructed a captive sample reactor (CSR) to study fast pyrolysis of biomass. The reactor uses a stainless steel wire mesh to surround biomass materials with an isothermal environment by independent controlling of heating rates and pyrolysis temperatures. The vapors produced during pyrolysis are immediately entrained and transported in He carrier gas to a molecular beam mass spectrometer (MBMS). Formation of secondary products is minimized by rapidly quenching the sample support with liquid nitrogen. A range of alkali and alkaline earth metal (AAEM) and transition metal salts were tested to study their effect on composition of primary pyrolysis products.more » Multivariate curve resolution (MCR) analysis of the MBMS data shows that transition metal salts enhance pyrolysis of carbohydrates and AAEM salts enhances pyrolysis of lignin. This was supported by performing similar separate studies on cellulose, hemicellulose and extracted lignin. The effect of salts on char formation is also discussed.« less

The effect of 150μm expandable graphite on char expansion of intumescent fire retardant coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ullah, Sami, E-mail: samichemist1@gmail.com; Shariff, A. M., E-mail: azmish@petronas.com.my, E-mail: azmibustam@petronas.com.my; Bustam, M. A., E-mail: azmish@petronas.com.my, E-mail: azmibustam@petronas.com.my

2014-10-24

Intumescent is defined as the swelling of certain substances to insulate the underlying substrate when they are heated. In this research work the effect of 150μm expandable graphite (EG) was studied on char expansion, char morphology and char composition of intumescent coating formulations (ICFs). To study the expansion and thermal properties of the coating, nine different formulations were prepared. The coatings were tested at 500 °C for one hour and physically were found very stable and well bound with the steel substrate. The morphology was studied by Scanning Electron Microscopy (SEM). The char composition was analysed by X-ray Diffraction (XRD)more » and Fourier transform infrared spectroscopy (FTIR) techniques. EG above than 10.8wt% expands the char abruptly with uniform network structure and affect the outer surface of the char.« less

Evaluating the combustion reactivity of drop tube furnace and thermogravimetric analysis coal chars with a selection of metal additives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katherine Le Manquais; Colin E. Snape; Ian McRobbie

Opportunities exist for effective coal combustion additives that can reduce the carbon content of pulverized fuel ash (PFA) to below 6%, thereby making it saleable for filler/building material applications without the need for postcombustion treatment. However, with only limited combustion data currently available for the multitude of potential additives, catalytic performance under pulverized fuel (PF) boiler conditions has received relatively little attention. This paper therefore compares the reactivity of catalyzed bituminous coal chars from thermogravimetric analysis (TGA) with those generated by devolatilization in a drop tube furnace (DTF). The principal aim was to explore the fundamental chemistry behind the chosenmore » additives' relative reactivities. Accordingly, all eight of the investigated additives increased the TGA burnout rate of the TGA and DTF chars, with most of the catalysts demonstrating consistent reactivity levels across chars from both devolatilization methods. Copper(I) chloride, silver chloride, and copper nitrate were thus identified as the most successful additives tested, but it proved difficult to establish a definitive reactivity ranking. This was largely due to the use of physical mixtures for catalyst dispersion, the relatively narrow selection of additives examined, and the inherent variability of the DTF chars. Nevertheless, one crucial exception to normal additive behavior was discovered, with copper(I) chloride perceptibly deactivating during devolatilization in the DTF, even though it remained the most effective catalyst tested. As a prolonged burnout at over 1000{sup o}C was required to replicate this deactivation effect on the TGA, the phenomenon could not be detected by typical testing procedures. Subsequently, a comprehensive TGA study showed no obvious relationship between the catalyst-induced reductions in the reaction's apparent activation energy and the samples recorded burnout rates.« less

Predictive Method for Correct Identification of Archaeological Charred Grape Seeds: Support for Advances in Knowledge of Grape Domestication Process

PubMed Central

Ucchesu, Mariano; Orrù, Martino; Grillo, Oscar; Venora, Gianfranco; Paglietti, Giacomo; Ardu, Andrea; Bacchetta, Gianluigi

2016-01-01

The identification of archaeological charred grape seeds is a difficult task due to the alteration of the morphological seeds shape. In archaeobotanical studies, for the correct discrimination between Vitis vinifera subsp. sylvestris and Vitis vinifera subsp. vinifera grape seeds it is very important to understand the history and origin of the domesticated grapevine. In this work, different carbonisation experiments were carried out using a hearth to reproduce the same burning conditions that occurred in archaeological contexts. In addition, several carbonisation trials on modern wild and cultivated grape seeds were performed using a muffle furnace. For comparison with archaeological materials, modern grape seed samples were obtained using seven different temperatures of carbonisation ranging between 180 and 340ºC for 120 min. Analysing the grape seed size and shape by computer vision techniques, and applying the stepwise linear discriminant analysis (LDA) method, discrimination of the wild from the cultivated charred grape seeds was possible. An overall correct classification of 93.3% was achieved. Applying the same statistical procedure to compare modern charred with archaeological grape seeds, found in Sardinia and dating back to the Early Bronze Age (2017–1751 2σ cal. BC), allowed 75.0% of the cases to be identified as wild grape. The proposed method proved to be a useful and effective procedure in identifying, with high accuracy, the charred grape seeds found in archaeological sites. Moreover, it may be considered valid support for advances in the knowledge and comprehension of viticulture adoption and the grape domestication process. The same methodology may also be successful when applied to other plant remains, and provide important information about the history of domesticated plants. PMID:26901361

Predictive Method for Correct Identification of Archaeological Charred Grape Seeds: Support for Advances in Knowledge of Grape Domestication Process.

PubMed

Ucchesu, Mariano; Orrù, Martino; Grillo, Oscar; Venora, Gianfranco; Paglietti, Giacomo; Ardu, Andrea; Bacchetta, Gianluigi

2016-01-01

The identification of archaeological charred grape seeds is a difficult task due to the alteration of the morphological seeds shape. In archaeobotanical studies, for the correct discrimination between Vitis vinifera subsp. sylvestris and Vitis vinifera subsp. vinifera grape seeds it is very important to understand the history and origin of the domesticated grapevine. In this work, different carbonisation experiments were carried out using a hearth to reproduce the same burning conditions that occurred in archaeological contexts. In addition, several carbonisation trials on modern wild and cultivated grape seeds were performed using a muffle furnace. For comparison with archaeological materials, modern grape seed samples were obtained using seven different temperatures of carbonisation ranging between 180 and 340ºC for 120 min. Analysing the grape seed size and shape by computer vision techniques, and applying the stepwise linear discriminant analysis (LDA) method, discrimination of the wild from the cultivated charred grape seeds was possible. An overall correct classification of 93.3% was achieved. Applying the same statistical procedure to compare modern charred with archaeological grape seeds, found in Sardinia and dating back to the Early Bronze Age (2017-1751 2σ cal. BC), allowed 75.0% of the cases to be identified as wild grape. The proposed method proved to be a useful and effective procedure in identifying, with high accuracy, the charred grape seeds found in archaeological sites. Moreover, it may be considered valid support for advances in the knowledge and comprehension of viticulture adoption and the grape domestication process. The same methodology may also be successful when applied to other plant remains, and provide important information about the history of domesticated plants.

Physico-chemical properties and gasification reactivity of co-pyrolysis char from different rank of coal blended with lignocellulosic biomass: Effects of the cellulose.

PubMed

Wu, Zhiqiang; Wang, Shuzhong; Luo, Zhengyuan; Chen, Lin; Meng, Haiyu; Zhao, Jun

2017-07-01

In this paper, the influence of cellulose on the physicochemical properties and the gasification reactivity of co-pyrolysis char was investigated. A specific surface area analyzer and an X-ray diffraction system were used to characterize the pore structure and the micro-crystalline structure of char. Fractal theory and deconvolution method were applied to quantitatively investigate the influence of cellulose on the structure of co-pyrolysis char. The results indicate that the improvements in the pore structure due to the presence of cellulose are more pronounced in the case of anthracite char with respect to bituminous char. Cellulose promotes the ordering of micro-scale structure and the uniformity of both anthracite and bituminous char, while the negative synergetic effect was observed during gasification of co-pyrolysis char. The exponential relationships between fractal dimension and specific surface area were determined, along with the relations between the gasification reactivity index and the microcrystalline structure parameter. Copyright © 2017 Elsevier Ltd. All rights reserved.

A volumetric ablation model of EPDM considering complex physicochemical process in porous structure of char layer

NASA Astrophysics Data System (ADS)

Yang, Liu; Xiao-Jing, Yu; Jian-Ming, Ma; Yi-Wen, Guan; Jiang, Li; Qiang, Li; Sa, Yang

2017-06-01

A volumetric ablation model for EPDM (ethylene- propylene-diene monomer) is established in this paper. This model considers the complex physicochemical process in the porous structure of a char layer. An ablation physics model based on a porous structure of a char layer and another model of heterogeneous volumetric ablation char layer physics are then built. In the model, porosity is used to describe the porous structure of a char layer. Gas diffusion and chemical reactions are introduced to the entire porous structure. Through detailed formation analysis, the causes of the compact or loose structure in the char layer and chemical vapor deposition (CVD) reaction between pyrolysis gas and char layer skeleton are introduced. The Arrhenius formula is adopted to determine the methods for calculating carbon deposition rate C which is the consumption rate caused by thermochemical reactions in the char layer, and porosity evolution. The critical porosity value is used as a criterion for char layer porous structure failure under gas flow and particle erosion. This critical porosity value is obtained by fitting experimental parameters and surface porosity of the char layer. Linear ablation and mass ablation rates are confirmed with the critical porosity value. Results of linear ablation and mass ablation rate calculations generally coincide with experimental results, suggesting that the ablation analysis proposed in this paper can accurately reflect practical situations and that the physics and mathematics models built are accurate and reasonable.

Hormesis is induced in the red flour beetle Tribolium castaneum through ingestion of charred toast.

PubMed

Grünwald, Stefanie; Niedermeier, Janine; Wenzel, Uwe

2015-06-01

Charred foods are generally suspected to exert health threats by providing toxicants, such as acrylamide or polycyclic aromatic hydrocarbons. Using the red flour beetle Tribolium castaneum as a model organism, we tested its survival under heat stress in response to feeding charred toast. Survival of beetles was measured at 42 °C after a pre-feeding phase with flour enriched with increasing concentrations of charred toast. In order to assess the influence of key transcription factors for phase-I and phase-II xenobiotic metabolism, gene homologs for ahr and nrf-2, respectively, were knocked down by the use of RNA interference (RNAi). Beetles fed only charred toast died off much earlier than control beetles fed on flour, whereas beetles fed flour enriched with 5% charred toast survived significantly longer than the control. Both, ahr and nrf-2 proved essential in order to enable the increase in survival by the feeding of 5% charred toast. Moreover, functional loss of ahr and nrf-2 made the beetles hypersensitive versus the feeding of 100% charred toast. Finally, at the transcriptional level, it was shown that RNAi for ahr blocked the inducing activities of charred toast on nrf-2. Our studies suggest a hormetic response of the red flour beetle to feeding of charred toast that causes an increased stress resistance through the activation of ahr and nrf-2. Those adaptations, however, are saturable and accordingly the hormetic effects at increasing concentrations of the toxicants become expended.

Integration of behavioral tests and biochemical biomarkers of terrestrial isopod Porcellio scaber (Isopoda, Crustacea) is a promising methodology for testing environmental safety of chars.

PubMed

Madžarić, Suzana; Kos, Monika; Drobne, Damjana; Hočevar, Matej; Jemec Kokalj, Anita

2018-03-01

We investigated how different carbonized materials, or chars (olive mill pomace biochar (BC) and urban greens pruning residues hydrochar (HC)) affect an important member of soil fauna, the terrestrial isopod Porcellio scaber. The selection behavior of isopods towards chars after a 48 h exposure was studied in (i) soil-char amended tests with single and multiple choices, and (ii) tests with chars offered as pure material. Finally, we exposed the isopods to char-amended soils for a period of 14 days to follow the effect on food consumption, body mass and activities of enzymes that are commonly altered upon stressor exposure (acetylcholinesterase, AChE, and glutathione S-transferase, GST). We showed that isopods are able to select between char amended and un-amended soil and different forms of char amendments: a clear preference for BC, and avoidance of HC were evidenced. The preferences remained the same when the chars were sterilized leading to the conclusion that initial microorganism composition was not the reason for selection, but selection was governed by other chars' physico-chemical properties. It remains to be elucidated which of these properties were the dominant reason for the selection. We also showed that isopods intentionally use BC as food at a similar rate to alder leaves. Medium-term exposure to HC resulted in adverse effects on isopods because it led to reduced feeding and growth, in addition to increasing GST activity, although no alterations in AChE activity were found. We suggest that behavioral tests with P. scaber could be used as a fast, reliable and economically feasible screening method for determining the safety of chars for the soil environment. Results represent significant contribution in the field of char toxicity testing, highlighting the importance of tests with isopods as important members of soil meso fauna, with the aim of influencing environmental policies and quality standards. Copyright © 2017 Elsevier Ltd. All rights reserved.

Understanding environmental DNA detection probabilities: A case study using a stream-dwelling char Salvelinus fontinalis

Treesearch

Taylor M. Wilcox; Kevin S. McKelvey; Michael K. Young; Adam J. Sepulveda; Bradley B. Shepard; Stephen F. Jane; Andrew R. Whiteley; Winsor H. Lowe; Michael K. Schwartz

2016-01-01

Environmental DNA sampling (eDNA) has emerged as a powerful tool for detecting aquatic animals. Previous research suggests that eDNA methods are substantially more sensitive than traditional sampling. However, the factors influencing eDNA detection and the resulting sampling costs are still not well understood. Here we use multiple experiments to derive...

Structural analysis of char by Raman spectroscopy: Improving band assignments through computational calculations from first principles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Matthew W.; Dallmeyer, Ian; Johnson, Timothy J.

2016-04-01

Raman spectroscopy is a powerful tool for the characterization of many carbon 27 species. The complex heterogeneous nature of chars and activated carbons has confounded 28 complete analysis due to the additional shoulders observed on the D-band and high intensity 29 valley between the D and G-bands. In this paper the effects of various vacancy and substitution 30 defects have been systematically analyzed via molecular modeling using density functional 31 theory (DFT) and how this is manifested in the calculated gas-phase Raman spectra. The 32 accuracy of these calculations was validated by comparison with (solid-phase) experimental 33 spectra, with amore » small correction factor being applied to improve the accuracy of frequency 34 predictions. The spectroscopic effects on the char species are best understood in terms of a 35 reduced symmetry as compared to a “parent” coronene molecule. Based upon the simulation 36 results, the shoulder observed in chars near 1200 cm-1 has been assigned to the totally symmetric 37 A1g vibrations of various small polyaromatic hydrocarbons (PAH) as well as those containing 38 rings of seven or more carbons. Intensity between 1400 cm-1 and 1450 cm-1 is assigned to A1g 39 type vibrations present in small PAHs and especially those containing cyclopentane rings. 40 Finally, band intensity between 1500 cm-1 and 1550 cm-1 is ascribed to predominately E2g 41 vibrational modes in strained PAH systems. A total of ten potential bands have been assigned 42 between 1000 cm-1 and 1800 cm-1. These fitting parameters have been used to deconvolute a 43 thermoseries of cellulose chars produced by pyrolysis at 300-700 °C. The results of the 44 deconvolution show consistent growth of PAH clusters with temperature, development of non-45 benzyl rings as temperature increases and loss of oxygenated features between 400 °C and 46 600 °C« less

Expansion of high-temperature; high-pressure data set for coal gasification. Fifth quarterly report, September 28-December 28, 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solomon, P.R.; Serio, M.A.; Hamblen, D.G.

1985-01-01

During the fifth quarter, the gas mixing station for the high pressure reactor (HPR) system was completed. This station allows us to make reproducible binary mixtures of any two gases. It will be used for pyrolysis experiments in helium/nitrogen or oxygen/nitrogen and gasification experiments in helium/nitrogen or oxygen/nitrogen and gasification experiments in carbon dioxide/nitrogen. In addition, work began on modifications of the HPR system for high pressure (600 psig) operation. A limited amount of data was taken with the HPR system due to the modifications for the mixing station. However, the test plan experiments for pyrolysis in mixtures of heliummore » and nitrogen were completed. In general, there is a slightly higher yield of volatiles and lower yield of char as the helium content (heating rate) increases. A new technique for measuring char reactivity resulted from an Army SBIR program and was further developed under our other METC Contract. It has also been used to characterize chars generated under the current program. It was evident that the severity of the thermal treatment had a direct effect on char reactivity. In this regard, rapid heating to a relatively low temperature was most favorable while slow heating to a high temperature was least favorable. With regard to pressure effects on reactivity, our preliminary data indicated that higher pressures produce chars lower initial reactivity. A total of four experiments were done in the heated tube reactor (HTR) at 60 psig, 800/sup 0/C maximum tube temperature. The trends are the same as observed in the atmospheric pressure experiments for the same tube temperature and cold gas velocity. During the past quarter, a particle temperature (PT) model was under development for the high pressure entrained flow reactor (HPR). 5 refs., 5 figs.« less

The production of black carbon during managed burning of UK peatlands: could managed burning of peatlands lead to enhanced carbon storage?

NASA Astrophysics Data System (ADS)

Clay, G.; Worrall, F.

2008-12-01

Peatlands are the UK's largest single terrestrial carbon store with carbon stored in UK peatlands than in forests of Britain and France combined. Unlike most northern peatlands in the peat soils of the UK are heavily managed for recreation and agriculture and due to their proximity to major centres of population are under more anthropogenic pressure than most peatlands. A typical management strategy on UK upland peats is the use of managed fire to restrict vegetation. Fires are used upon a 10-25 year rotation and are described as "cool" as they are designed to remove the crown of the vegetation without scorching the litter layer or the underlying soil. In this case the fire destroys primary productivity and limits litter production but produces char. Char is a low volume, highly refractory, high carbon content product while litter is a high volume, decomposable, lower carbon content product. Therefore, the question is if there are fire conditions under which the production of char causes more carbon to be stored in the peat than would have been stored if no fire management had been employed. This study combines field studies of recent managed burns and wildfires along with detailed vegetation studies from a long term monitoring site in order to assess litter, biomass and black carbon production. In the laboratory experimental burns were undertaken in order to assess the amount and controls upon char production and the carbon content of that char. Results of field and laboratory observations are used to model carbon accumulation under a series of fire management scenarios and the modelling shows that cools burns at long rotations could lead to higher carbon storage than if no fire had occurred, further in several cases more carbon accumulation occurred even if less depth of peat was generated.

Investigating co-combustion characteristics of bamboo and wood.

PubMed

Liang, Fang; Wang, Ruijuan; Jiang, Changle; Yang, Xiaomeng; Zhang, Tao; Hu, Wanhe; Mi, Bingbing; Liu, Zhijia

2017-11-01

To investigate co-combustion characteristics of bamboo and wood, moso bamboo and masson pine were torrefied and mixed with different blend ratios. The combustion process was examined by thermogravimetric analyzer (TGA). The results showed the combustion process of samples included volatile emission and oxidation combustion as well as char combustion. The main mass loss of biomass blends occurred at volatile emission and oxidation combustion stage, while that of torrefied biomass occurred at char combustion stage. With the increase of bamboo content, characteristic temperatures decreased. Compared with untreated biomass, torrefied biomass had a higher initial and burnout temperature. With the increase of heating rates, combustion process of samples shifted to higher temperatures. Compared with non-isothermal models, activation energy obtained from isothermal model was lower. The result is helpful to promote development of co-combustion of bamboo and masson pine wastes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Laser machining wood composites

Treesearch

Vladimir Barnekov; Henry A. Huber; Charles W. McMillin

1989-01-01

This practical, nonstatistical experiment using commercial equipment demonstrated that nominal 3/4-inch compositep anelsf or furniture consisting of a particleboard core,h igh density melamine crossbands, and walnut veneer face plies can be cut with a carbon dioxide/airjet-assisted laser to produce surfaces with minimal nonparallelism and char compared to previous...

Thermal injury secondary to laparoscopic fiber-optic cables.

PubMed

Hindle, A Katharine; Brody, Fred; Hopkins, Vernon; Rosales, Greg; Gonzalez, Florencia; Schwartz, Arnold

2009-08-01

Laparoscopy requires a reliable light source to provide adequate visualization. However, thermal energy is produced as a by-product from the optical cable. This study attempts to quantify the degree of possible thermal damage secondary to the fiber-optic light source. Using a digital thermometer, temperature measurements were recorded at the tip of optical cables from five different light sources (Karl Storz, Inc., Tuttlingen, Germany). Temperature measurements were recorded with new and old bulbs. The tip of the cable was applied to surgical drapes and the time to charring was recorded. Subsequently, the tip of the optical cable was applied to a porcine model and tissue samples were obtained after varying amounts of time (5, 15, 30, 60, and 90 s). Sections of the damaged tissue were prepared for microscopic evaluation. Parameters for thermal injury included extent of epidermal, dermal, and subcutaneous fat damage and necrosis. The lateral extent and depth of injury were measured. The maximum temperature at the tip of the optical cable varied between 119.5 degrees C and 268.6 degrees C. When surgical drapes were exposed to the tip of the light source, the time to char was 3-6 s. The degree and volume of injury increased with longer exposure times, and significant injury was recorded with the optical cable 3 mm from the skin. This study demonstrates that the temperature at the tip of the optical light cord can induce extensive damage. The by-product of light, heat, can produce immediate superficial tissue necrosis that can extend into the subcutaneous fat even when the optical tip is not in direct contact with the skin. In addition, our study shows the variation in temperature that exists between light sources and bulb status. Overall, surgeons must realize and respect the potential complications associated with optical technology.

Physicochemical properties and gasification reactivity of the ultrafine semi-char derived from a bench-scale fluidized bed gasifier

NASA Astrophysics Data System (ADS)

Zhang, Yukui; Zhang, Haixia; Zhu, Zhiping; Na, Yongjie; Lu, Qinggang

2017-08-01

Zhundong coalfield is the largest intact coalfield worldwide and fluidized bed gasification has been considered as a promising way to achieve its clean and efficient utilization. The purpose of this study is to investigate the physicochemical properties and gasification reactivity of the ultrafine semi-char, derived from a bench-scale fluidized bed gasifier, using Zhundong coal as fuel. The results obtained are as follows. In comparison to the raw coal, the carbon and ash content of the semi-char increase after partial gasification, but the ash fusion temperatures of them show no significant difference. Particularly, 76.53% of the sodium in the feed coal has released to the gas phase after fluidized bed gasification. The chemical compositions of the semi-char are closely related to its particle size, attributable to the distinctly different natures of diverse elements. The semi-char exhibits a higher graphitization degree, higher BET surface area, and richer meso- and macropores, which results in superior gasification reactivity than the coal char. The chemical reactivity of the semi-char is significantly improved by an increased gasification temperature, which suggests the necessity of regasification of the semi-char at a higher temperature. Consequently, it will be considered feasible that these carbons in the semi-char from fluidized bed gasifiers are reclaimed and reused for the gasification process.

Removal of lead (Pb2+) from aqueous medium by using chars from co-pyrolysis.

PubMed

Bernardo, Maria; Mendes, Sandra; Lapa, Nuno; Gonçalves, Margarida; Mendes, Benilde; Pinto, Filomena; Lopes, Helena; Fonseca, Isabel

2013-11-01

The effectiveness of chars from the co-pyrolysis of pine, used tires and plastic wastes for the removal of lead (Pb(2+)) from aqueous medium, was investigated. The chars were predominantly of macroporous nature, but the introduction of tires in the pyrolysis feedstock enhanced their mesoporous content as well as surface area. Pb(2+) sorption with the chars was a slow and unstable process in which sorption-desorption seems to be competing. The highest Pb(2+) removal (88%) was attained by the char resulting from the pyrolysis of a mixture composed by equal mass ratios of used tires and plastics, at 48 h of contact time. This char was also the one with the overall better performance for Pb(2+) sorption, achieving almost 100% of Pb(2+) removal on the study of the effect of adsorbent dose. Mixing the three raw materials for pyrolysis had no advantage for the resulting char concerning the removal efficiency of Pb(2+). The sorption mechanisms varied according to the pyrolysis feedstock: in chars from feedstock with pine, chemisorption involving complexation with oxygenated surface functional groups followed by cation exchange was the presumable mechanism. In tire rubber derived chars, cation exchange with Ca(2+), K(+), and Zn(2+) played the major role on Pb(2+) sorption. Copyright © 2013 Elsevier Inc. All rights reserved.

Co-pyrolysis of corn cob and waste cooking oil in a fixed bed.

PubMed

Chen, Guanyi; Liu, Cong; Ma, Wenchao; Zhang, Xiaoxiong; Li, Yanbin; Yan, Beibei; Zhou, Weihong

2014-08-01

Corn cob (CC) and waste cooking oil (WCO) were co-pyrolyzed in a fixed bed. The effects of various temperatures of 500 °C, 550 °C, 600 °C and CC/WCO mass ratios of 1:0, 1:0.1, 1:0.5, 1:1 and 0:1 were investigated, respectively. Results show that co-pyrolysis of CC/WCO produce more liquid and less bio-char than pyrolysis of CC individually. Bio-oil and bio-char yields were found to be largely dependent on temperature and CC/WCO ratios. GC/MS of bio-oil show it consists of different classes and amounts of organic compounds other than that from CC pyrolysis. Temperature of 550 °C and CC/WCO ratio of 1:1 seem to be the optimum considering high bio-oil yields (68.6 wt.%) and good bio-oil properties (HHV of 32.78 MJ/kg). In this case, bio-char of 24.96 MJ/kg appears attractive as a renewable source, while gas with LHV of 16.06 MJ/Nm(3) can be directly used in boilers as fuel. Copyright © 2014 Elsevier Ltd. All rights reserved.

An evaluation of the efficacy of various coal combustion models for predicting char burnout

DOE Office of Scientific and Technical Information (OSTI.GOV)

McConnell, Josh; Goshayeshi, Babak; Sutherland, James C.

Coal combustion is comprised of several subprocesses including devolatilization and heterogeneous reactions of the coal char with O 2, CO 2, H 2O and potentially several other species. Much effort has been put forth to develop models for these processes which vary widely in both complexity and computational cost. This work investigates the efficacy of models for devolatilization and char reactions at either end of the complexity and cost spectrums for a range of particle sizes and furnace temperatures and across coal types. The overlap of simulated devolatilization and char consumption is also examined. In the gas phase, a detailedmore » kinetics model based on a reduced version of the GRI 3.0 mechanism is used. The Char Conversion Kinetics and an n th-order Langmuir-Hinshelwood models are considered for char oxidation. The Chemical Percolation and Devolatilization and a two-step model are considered for devolatilization. Results indicate that high-fidelity models perform better at representing particle temperature and mass data across a wide range of O 2 concentrations as well as coal types. A significant overlap in devolatilization and char consumption is observed for both char chemistry and devolatilization models.« less

An evaluation of the efficacy of various coal combustion models for predicting char burnout

DOE PAGES

McConnell, Josh; Goshayeshi, Babak; Sutherland, James C.

2016-11-22

Coal combustion is comprised of several subprocesses including devolatilization and heterogeneous reactions of the coal char with O 2, CO 2, H 2O and potentially several other species. Much effort has been put forth to develop models for these processes which vary widely in both complexity and computational cost. This work investigates the efficacy of models for devolatilization and char reactions at either end of the complexity and cost spectrums for a range of particle sizes and furnace temperatures and across coal types. The overlap of simulated devolatilization and char consumption is also examined. In the gas phase, a detailedmore » kinetics model based on a reduced version of the GRI 3.0 mechanism is used. The Char Conversion Kinetics and an n th-order Langmuir-Hinshelwood models are considered for char oxidation. The Chemical Percolation and Devolatilization and a two-step model are considered for devolatilization. Results indicate that high-fidelity models perform better at representing particle temperature and mass data across a wide range of O 2 concentrations as well as coal types. A significant overlap in devolatilization and char consumption is observed for both char chemistry and devolatilization models.« less

Comparative Performance of Three Magnesium Compounds on Thermal Degradation Behavior of Red Gum Wood.

PubMed

Wu, Yiqiang; Yao, Chunhua; Hu, Yunchu; Zhu, Xiaodan; Qing, Yan; Wu, Qinglin

2014-01-24

The effect of basic magnesium carbonate (BMC), magnesium hydroxide (MH), and magnesium chloride hydrate (MCH) on thermal degradation of red gum wood was studied using cone calorimetry, Thermogravimetric-differential scanning calorimetry (TG-DSC) analysis, and X-ray diffraction (XRD) characterization. The results showed common fire retardation actions of the three compounds by releasing incombustible gas and/or water vapor to dilute combustible gas in the flaming zone, and by converting to MgO, which had a satisfactory protective wall effect on the wood. Individually, BMC absorbed heat from the wood at the pre-decomposition stage and, thus, slowed down wood pyrolysis process. It slightly increased the char yield by charring in both the charring stage and the char calcination stage. MH lost water at about 270 °C, close to the temperature at which wood thermally degraded. MH rendered wood char quickly, and the compact char layer impeded further carbonization and burning of inner wood. MCH promoted charring with Mg 2+ as a Lewis acid, and increased wood char yield. MCH also released Cl· free radical and HCl at 167 °C, which easily coordinated with combustion reaction radical, and slowed down, even inhibited, the combustion chain reaction.

Comparative Performance of Three Magnesium Compounds on Thermal Degradation Behavior of Red Gum Wood

PubMed Central

Wu, Yiqiang; Yao, Chunhua; Hu, Yunchu; Zhu, Xiaodan; Qing, Yan; Wu, Qinglin

2014-01-01

The effect of basic magnesium carbonate (BMC), magnesium hydroxide (MH), and magnesium chloride hydrate (MCH) on thermal degradation of red gum wood was studied using cone calorimetry, Thermogravimetric-differential scanning calorimetry (TG-DSC) analysis, and X-ray diffraction (XRD) characterization. The results showed common fire retardation actions of the three compounds by releasing incombustible gas and/or water vapor to dilute combustible gas in the flaming zone, and by converting to MgO, which had a satisfactory protective wall effect on the wood. Individually, BMC absorbed heat from the wood at the pre-decomposition stage and, thus, slowed down wood pyrolysis process. It slightly increased the char yield by charring in both the charring stage and the char calcination stage. MH lost water at about 270°C, close to the temperature at which wood thermally degraded. MH rendered wood char quickly, and the compact char layer impeded further carbonization and burning of inner wood. MCH promoted charring with Mg2+ as a Lewis acid, and increased wood char yield. MCH also released Cl· free radical and HCl at 167°C, which easily coordinated with combustion reaction radical, and slowed down, even inhibited, the combustion chain reaction. PMID:28788480

Improved lignin pyrolysis for phenolics production in a bubbling bed reactor--Effect of bed materials.

PubMed

Li, Dongbing; Briens, Cedric; Berruti, Franco

2015-01-01

Lignin pyrolysis was studied in a bubbling fluidized bed reactor equipped with a fractional condensation train, using nitrogen as the fluidization gas. The effect of different bed materials (silica sand, lignin char, activated lignin char, birch bark char, and foamed glass beads) on bio-oil yield and quality was investigated for a pyrolysis temperature of 550 °C. Results how that a bed of activated lignin char is preferable to the commonly used silica sand: pyrolysis of Kraft lignin with a bed of activated lignin char not only provides a pure char product, but also a higher dry bio-oil yield (with a relative increase of 43%), lower pyrolytic water production, and better bio-oil quality. The bio-oil obtained from Kraft lignin pyrolysis with a bed of activated lignin char has a lower average molecular weight, less tar, more phenolics, and less acidity than when sand is used as bed material. Copyright © 2015 Elsevier Ltd. All rights reserved.

The thermal and mechanical properties of a low density elastomeric ablation material

NASA Technical Reports Server (NTRS)

Engelke, W. T.; Robertson, R. W.; Bush, A. L.; Pears, C. D.

1973-01-01

Thermal and mechanical properties data were obtained for a low density elastomeric resin based ablation material with phenolic-glass honeycomb reinforcement. Data were obtained for the material in the charred and uncharred state. Ablation material specimens were charred in a laboratory furnace at temperatures in the range from 600 K to 1700 K to obtain char specimens representative of the ablation char layer formed during reentry. These specimens were then used to obtain effective thermal conductivity, heat capacity, porosity, and permeability data at the char formation temperature. This provided a boxing of the data which enables the prediction of the transient response of the material during ablation. Limited comparisons were made between the furnace charred specimens and specimens which had been exposed to simulated reentry conditions.

Influence of carbonization conditions on the pyrolytic carbon deposition in acacia and eucalyptus wood chars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, M.; Gupta, R.C.

1997-04-01

The amount of deposited pyrolytic carbon (resulting from the cracking of volatile matter) was found to depend on wood species and carbonization conditions, such as temperature and heating rate. Maximum pyrolytic carbon deposition in both the acacia and eucalyptus wood chars has been observed at a carbonization temperature of 800 C. Rapid carbonization (higher heating rate) of wood significantly reduces the amount of deposited pyrolytic carbon in resulting chars. Results also indicate that the amount of deposited pyrolytic carbon in acacia wood char is less than that in eucalyptus wood char.

Proceedings of the 7th Semiannual Meeting of the Nozzle Initiative Industry Advisory Committee on Standardization of Carbon-Phenolic Test Methods and Specifications

NASA Technical Reports Server (NTRS)

Hall, William B. (Compiler); Pinoli, Pat C. (Compiler); Upton, Cindy G. (Compiler)

1991-01-01

The application of carbon fibers and fabrics (CF) for producing rocket nozzles is discussed. These materials which are essential for fabricating the carbon composites used in aerospace systems gasify when exposed to high temperatures and the mechanical properties of the composites degrade. The oxidation kinetics under isothermal (IC) and non-isothermal (NIC) conditions are examined and a comparison is made between the characteristics of IC and NIC oxidation. Several CF, chars, and carbon blacks were examined, including a microporous char, a graphitized rayon fabric, and several carbonized rayon fabrics. A summary is given of the advantages and drawbacks of isothermal and non-isothermal oxidation of carbons. The proceedings are assembled in the form of a roundtable discussion.

Using environmental chemistry technologies for the removal of arsenic from drinking water, and fat and oil based phase change materials for thermal energy storage

NASA Astrophysics Data System (ADS)

Sutterlin, William R.

The first four chapters of this dissertation involve the removal of arsenic from drinking water. Various forms of a macroporous char prepared by partial gasification of subbituminous coal were studied for removal of arsenic(V) and arsenic(III) from water. In increasing order of effectiveness for arsenic(V) removal were untreated char < acid-washed char < char impregnated with iron(III) and gasified < char impregnated with FeS < char impregnated with iron(III) hydroxide < char coated with zerovalent iron < char impregnated with iron(III) oxide. A mass of 10 g of iron(III) oxide char removed arsenic(V) and arsenic(III) from 10,000 mL of water containing 500 micrograms/L of arsenic to levels below 10 micrograms/L. The capacity of the solid to remove arsenic was significantly diminished in water containing 4 mg/L of phosphate. An electrical current passed over 4 g of iron(III) oxide char in a column enabled removal of arsenic(III) from 14,000 mL of 500 micrograms/L arsenic(III) to below 10 micrograms/liter and at significantly higher flow rates than could be employed without electrolysis. The fifth chapter in this dissertation focused on the retention of organics onto a char/concrete pellet. A mixture of naphthalene, pentachlorophenol, biphenyl, toluene, tetrachloroethane, and chlorobenzene were impregnated into a loose granular char, a char/concrete pellet and a sand/concrete pellet. The results showed that the char/concrete pellet had significant advantages over the other forms. Chapters 6--9 focus on phase change materials (PCMs). These PCMs are made from fats and oils. PCMs are perhaps the only proven method that can provide near 100% thermal energy storage. In chapter 7 a novel HPLC method was developed that could provide quantification and qualification of the resulting products formed after PCM synthesis. In chapter 8 thermal cycling studies were conducted on the fat and oil based PCMs. These thermal cycle demonstrated that these PCMs were capable of going through a multitude of freeze and melt processes with little to no degradation if the appropriate preservative is used. Finally in chapter 9 the PCM is incorporated into a simulated 100 th scale house. A traditional freon based evaporator is used to freeze the PCM at night during electrical-off-peak hours. During the peak-load of the day the evaporator is turned off and the PCM provides the cooling for the house.

Distribution, Transport, and Accumulation of Pyrogenic Black Carbon in Post-Wildfire Watersheds

NASA Astrophysics Data System (ADS)

Galanter, A.; Cadol, D. D.; Frey, B.; Lohse, K. A.

2014-12-01

Large, high severity wildfires greatly alter forest structure, water quality, and soil development/erosion. With increased frequency of such wildfires also follows heavy post-wildfire debris flows and flooding which deliver high loads of sediment and pyrogenic black carbon (PyC) to downstream waterways. The accumulation of PyC is a multi-faceted and dynamic issue in the critical zone. Generated by incomplete combustion of organic matter, PyC (in the form of soot and char) impacts turbidity, biological and chemical oxygen demand, and pH. In addition, PyC has the potential to sequester contaminants and can store carbon over short and long timescales. The impacts of two recent wildfires in Northern New Mexico are studied with the goal of understanding the fluxes and residence times of PyC in post-wildfire, mountainous watersheds. Employing burn severity maps and geospatial data, we selected three sites to collect soil and water samples to characterize PyC: a control, an area impacted by a large, severe burn (2011), and an area impacted by a smaller, less severe burn (2013). By collaborating with researchers at the Jemez Critical Zone Observatory, soil samples are being analyzed and will provide pre-wildfire PyC concentrations for the 2013 burn area. In this study, PyC is treated as both a particulate and a solute that is transported throughout the watershed as well as degraded in soils, surface water and groundwater. We used two black carbon quantification methods: the chemo-thermal oxidation (CTO-375) method to distinguish between soil soot and char, and the benzene polycarboxylic acids (BPCA) method to quantify the total concentrations of PyC in soil and water samples. Preliminary soil data from the CTO-375 method show comparable soot concentrations in the control, 2011, and 2013 burn indicating that the soot is more recalcitrant than char and remains in the watershed long after a wildfire. This data also suggests that the fluxes of black carbon over short time scales are composed mainly of char.

The effects of the conditions of char formation on the physical properties of charred phenolic-nylon

NASA Technical Reports Server (NTRS)

Smyly, E. D.; Pears, C. D.

1972-01-01

A study was made of the effects of the conditions of char formation on the physical properties of charred phenolic nylon of 0.577 gm/cu cm density. It was found that the thermal conductivity and several of the monitors correlate well with degradation conditions. The monitors included electrical resistivity, sonic velocity, porosity, lattice spacing and crystallite size.

Pyrochars and hydrochars differently alter the sorption of the herbicide isoproturon in an agricultural soil.

PubMed

Eibisch, Nina; Schroll, Reiner; Fuß, Roland; Mikutta, Robert; Helfrich, Mirjam; Flessa, Heinz

2015-01-01

Carbonaceous material from pyrolysis (pyrochars) and hydrothermal carbonization (hydrochars) are applied to soil to improve soil fertility and carbon sequestration. As a positive side effect, the mobility of pesticides and the risk of groundwater contamination can be minimized. However, the impact of various raw materials on the sorption capacity of different pyrochars and hydrochars is poorly understood. Thus, sorption experiments were performed with (14)C-labeled isoproturon (IPU, 0.75 kg ha(-1)) in a loamy sand soil amended with either pyrochar or hydrochar (0.5% and 5% dry weight, respectively). Carbonaceous materials were produced from three different raw materials: corn digestate, miscanthus, woodchips of willow and poplar. After 72 h of incubation, a sequential extraction procedure was conducted to quantify in situ IPU bioavailability, total amount of extractable IPU, and non-extractable pesticide residues (NER). Added char amount, carbonization type, and raw materials had statistically significant effects on the sorption of IPU. The amount of in situ available IPU was reduced by a factor of 10-2283 in treatments with pyrochar and by a factor of 3-13 in hydrochar treatments. The surface area of the charred material was the most predictive variable of IPU sorption to char amended soil. Some physical and chemical char properties tend to correlate with pore water-, methanol- or non-extractable IPU amounts. Due to a low micro-porosity and ash content, high water extractable carbon contents and O-functional groups of hydrochars, the proportion of NER in hydrochar amended soils was considerably lower than in soil amended with pyrochars. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of Kinetics and Mathematical Models for High Pressure Gasification of Lignite-Switchgrass Blends

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agrawal, Pradeep K.

The overall objective of the current project was to investigate the high pressure gasification characteristics of a feed containing both coal and biomass. The two feed types differ in their ash contents and ash composition, particularly the alkali content. Gasification of a combined feed of coal and biomass has the potential for considerable synergies that might lead to a dramatic improvement in process economics and flexibility. The proposed study aimed to develop a detailed understanding of the chemistry, kinetics, and transport effects during high pressure gasification of coal-biomass blend feed. Specifically, we studied to develop: (a) an understanding of themore » catalytic effect of alkali and other inorganic species present in the biomass and coal, (b) an understanding of processing conditions under which synergistic effects of the blending of coal and biomass might be observed. This included the role of particle size, residence time, and proximity of the two feed types, (c) kinetics of high pressure gasification of individual feeds as well as the blends, and (d) development of mathematical models that incorporate kinetics and transport models to enable prediction of gasification rate at a given set of operating conditions, and (e) protocols to extend the results to other feed resources. The goal was to provide a fundamental understanding of the gasification process and guide in optimizing the configurations and design of the next generation of gasifiers. The approach undertaken was centered on two basic premises: (1) the gasification for small particles without internal mass transfer limitations can be treated as the sum of two processes in series (pyrolysis and char gasification) , and (2) the reactivity of the char generated during pyrolysis not only depends on the pressure and temperature but is also affected by the heating rates. Thus low heating rates (10-50 °C/min) typical of PTGA fail to produce char that would typically be formed at high heating rates (~10 4 °C/sec), encountered in entrained flow gasifiers. The char morphology, also a function of the heating rate, would influence the transport rates during the char gasification phase. Thus, heating rate plays a critical role through which both, pyrolysis and char gasification, are interconnected. We utilized two complementary gasification experiments: PEFR (pressurized entrained flow gasifier) and PTGA (pressurized thermo-gravimetric analyzer). The PEFR allowed us to study gasification at pressures, temperatures, and heating rates relevant for coal-biomass gasifiers. The PTGA work was useful in understanding the basic chemistry of the evolution of various gaseous species during pyrolysis. These results helped improved our understanding of the chemistry and chemical changes during pyrolysis. The role alkali metals and other inorganics in char gasification using steam and/or CO 2 was investigated. Finally, the mathematical models for char gasification without the transport effects were developed at commercial operating conditions.« less

Characterization of pyrolytic products obtained from fast pyrolysis of chromated copper arsenate (CCA)- and alkaline copper quaternary compounds (ACQ)-treated wood biomasses.

PubMed

Kim, Jae-Young; Kim, Tae-Sung; Eom, In-Yong; Kang, Sung Mo; Cho, Tae-Su; Choi, In Gyu; Choi, Joon Weon

2012-08-15

In this study, chromated copper arsenate-treated wood (CCA-W) and alkaline copper quaternary compounds-treated wood (ACQ-W) were subjected to fast pyrolysis at 500°C for ca. 2s to produce bio-oil and char. The physicochemical properties of the pyrolytic products as well as the distribution of heavy metals - arsenic, copper and chrome - during fast pyrolysis were investigated. The water content, viscosity, pH and higher heating value (HHV) of bio-oil from CCA-W were 24.8 wt%, 13.5 cSt, 2.1 and 16 MJ/kg, respectively, whereas those of bio-oil from ACQ-W were 27.9 wt%, 16 cSt, 3.0 and 14.1 MJ/kg, respectively. The yields of bio-oil from CCA-W and ACQ-W were 43.3% and 46.6%, respectively, significantly lower than that of control (61.6%). In the pyrolytic products of CCA-W, the concentrations of arsenic, copper and chromium were determined to be 36.4 wt%, 74.0 wt% and 75.4 wt% in char, respectively, 34.5 wt%, 10.3 wt% and 9.0 wt% in bio-oil, respectively, and 29.0 wt%, 15.7 wt% and 15.5 wt% in gas, respectively. In addition, most of the copper appeared in the char (98.8 wt%) and only a trace amount of copper was detected in the bio-oil (0.2 wt%) produced by ACQ-W. Copyright © 2012 Elsevier B.V. All rights reserved.

[Dynamics of the parasite fauna of various forms of chars, salvelinus alpinus L., of the Lake Azabach'e basin].

PubMed

Butorina, T E

1975-01-01

The paper deals with age changes in the parasite fauna of different intraspecific forms of chars. It is shown that this year brood and yearlings of predatory, benthofagous, stream and anadromous chars up to 10 cm in length have a similar parasite fauna. During the second year of life the chars come to different feeding; correspondingly changes their parasite fauna which differs considerably in the above forms of chars. Two groups of parasites are distinguished the infection with which increases and decreases with the age of fishes. Observations were carried out on the life cycles, developmental and maturation periods of some parasites of chars. Biological peculiarities of some mixosporidia are studied. A shift in the developmental periods of helminths is noted as compared to those from the European part of the USSR.

Co-gasification of coal and biomass: Synergy, characterization and reactivity of the residual char.

PubMed

Hu, Junhao; Shao, Jingai; Yang, Haiping; Lin, Guiying; Chen, Yingquan; Wang, Xianhua; Zhang, Wennan; Chen, Hanping

2017-11-01

The synergy effect between coal and biomass in their co-gasification was studied in a vertical fixed bed reactor, and the physic-chemical structural characteristics and gasification reactivity of the residual char obtained from co-gasification were also investigated. The results shows that, conversion of the residual char and tar into gas is enhanced due to the synergy effect between coal and biomass. The physical structure of residual char shows more pore on coal char when more biomass is added in the co-gasification. The migration of inorganic elements between coal and biomass was found, the formation and competitive role of K 2 SiO 3 , KAlSiO 4 , and Ca 3 Al 2 (SiO 4 ) 3 is a mechanism behind the synergy. The graphization degree is enhanced but size of graphite crystallite in the residual char decreases with biomass blending ratio increasing. TGA results strongly suggest the big difference in the reactivity of chars derived from coal and biomass in spite of influence from co-gasification. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fire-Resistant Composites

NASA Technical Reports Server (NTRS)

Kourtides, D. A.; Parker, J. A.

1983-01-01

Resin blend produces high-char-yield, low-smoke composites. Diglycidyl Ether of Bis-(4-Hydroxyphenyl)-Fluorene is prepared by reacting epichlorohydrin and sodium hydroxide with 9,9-bis(hydroxyphenyl) fluorene. End of reaction determined by gas or liquid chromatography, mass spectroscopy or infrared techniques. Used to manufacture printed circuit boards and panels for buildings, ships and aircraft.

Determination of Copper by Graphite Furnace Atomic Absorption Spectrophotometry: A Student Exercise in Instrumental Methods of Analysis.

ERIC Educational Resources Information Center

Williamson, Mark A.

1989-01-01

Discusses a student exercise which requires the optimizing of the charring and atomization temperatures by producing a plot of absorbance versus temperature for each temperature parameter. Notes that although the graphite furnace atomic absorption spectroscopy technique has widespread industrial use, there are no published, structured experiments…

Into the Unknown: The Logistics Preparation of the Lewis and Clark Expedition

DTIC Science & Technology

2003-06-06

boils), “pox” (syphilis, also called Lues or French Disease), “char lick” ( colic ), and “biliousness.” Lewis and Clark had a rudimentary knowledge of...secretion producing dark stools; also a diuretic; given orally, has an anti-syphilitic action; ingredient of Dr. Rush’s Bilious Pills. Cream of tartar

Synthesis, structural and flammability studies of novel phosphonates triazine derivative as economic flame retardant for cotton

USDA-ARS?s Scientific Manuscript database

Organophosphorous flame retardants have been known to be more effective when used in conjunction with nitrogen-containing systems. Their mixture produces incombustible non-toxic gases which can dilute the concentration of the oxygen near the flame, and the charred layers become protective barriers t...

16 CFR § 1616.5 - Test procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

Intumescent flame-retardant cotton produced by tannic acid and sodium hydroxide

USDA-ARS?s Scientific Manuscript database

This study showed that tannic acid can form intumescent flame-retardant coating on cotton nonwoven fabric with an aid of NaOH. Tannic acid alone altered the thermal patterns of the pyrolysis and combustion of cotton and increased the char yield, but its improvement in limiting oxygen index (LOI) wa...

Marshall Convergent Spray Formulation Improvement for High Temperatures

NASA Technical Reports Server (NTRS)

Scarpa, Jack; Patterson,Chat

2011-01-01

The Marshall Convergent Coating-1 (MCC-1) formulation was produced in the 1990s, and uses a standard bisphenol A epoxy resin system with a triamine accelerator. With the increasing heat rates forecast for the next generation of vehicles, higher-temperature sprayable coatings are needed. This work substitutes the low-temperature epoxy resins used in the MCC-1 coating with epoxy phenolic, epoxy novalac, or resorcinolinic resins (higher carbon content), which will produce a higher char yield upon exposure to high heat and increased glass transition temperature. High-temperature filler materials, such as granular cork and glass ecospheres, are also incorporated as part of the convergent spray process, but other sacrificial (ablative) materials are possible. In addition, the use of polyhedral oligomeric silsesquioxanes (POSS) nanoparticle hybrids will increase both reinforcement aspects and contribute to creating a tougher silacious char, which will reduce recession at higher heat rates. Use of expanding epoxy resin (lightweight MCC) systems are also useful in that they reduce system weight, have greater insulative properties, and a decrease in application times can be realized.

Temporal trends of contaminants in Arctic char (Salvelinus alpinus) from a small lake, southwest Greenland during a warming climate.

PubMed

Rigét, Frank; Vorkamp, Katrin; Muir, Derek

2010-12-01

Hg and legacy POPs were analysed in muscle tissue of a landlocked Arctic char (Salvelinus alpinus) population from a small lake in southwest Greenland. Hg concentrations were available for six years and OC concentrations for five years during the period 1994 to 2008. For two years, stable isotope values of nitrogen (δ(15)N) were analysed in muscle tissue in order to infer trophic effects. Hg, Σ10-PCB, ΣDDT and trans-nonachlor concentrations (OC on wet weight basis) showed an increase with increasing fish length, which had to be accounted for when assessing temporal trends. δ(15)N values had a narrow range, and there was no indication of increasing δ(15)N values with char length confirming the sampled char did not vary in trophic morphs as often seen in Arctic lakes. Length-adjusted Hg concentrations showed a significantly increasing trend during the period 1994 to 2008, while Σ10-PCB, ΣDDT, ΣHCH and trans-nonachlor showed a significantly decreasing trend when expressed on wet weight, and decreasing but not significantly when expressed on lipid weight. The reason for this was that the lipid content of muscle showed a significantly decreasing trend with time. The sum of mean monthly air temperature during May to August measured at a nearby meteorological station showed an increasing trend during the study period, and changing temperature conditions probably influenced the temporal trend of especially Hg concentrations and the lipid content.

Molecular-scale characterization of uranium sorption by bone apatite materials for a permeable reactive barrier demonstration

USGS Publications Warehouse

Fuller, C.C.; Bargar, J.R.; Davis, J.A.

2003-01-01

Uranium binding to bone charcoal and bone meal apatite materials was investigated using U LIII-edge EXAFS spectroscopy and synchrotron source XRD measurements of laboratory batch preparations in the absence and presence of dissolved carbonate. Pelletized bone char apatite recovered from a permeable reactive barrier (PRB) at Fry Canyon, UT, was also studied. EXAFS analyses indicate that U(VI) sorption in the absence of dissolved carbonate occurred by surface complexation of U(VI) for sorbed concentrations ??? 5500 ??g U(VI)/g for all materials with the exception of crushed bone char pellets. Either a split or a disordered equatorial oxygen shell was observed, consistent with complexation of uranyl by the apatite surface. A second shell of atoms at a distance of 2.9 A?? was required to fit the spectra of samples prepared in the presence of dissolved carbonate (4.8 mM total) and is interpreted as formation of ternary carbonate complexes with sorbed U(VI). A U-P distance at 3.5-3.6 A?? was found for most samples under conditions where uranyl phosphate phases did not form, which is consistent with monodentate coordination of uranyl by phosphate groups in the apatite surface. At sorbed concentrations ??? 5500 ??g U(VI)/g in the absence of dissolved carbonate, formation of the uranyl phosphate solid phase, chernikovite, was observed. The presence of dissolved carbonate (4.8 mM total) suppressed the formation of chernikovite, which was not detected even with sorbed U(VI) up to 12 300 ??g U(VI)/g in batch samples of bone meal, bone charcoal, and reagent-grade hydroxyapatite. EXAFS spectra of bone char samples recovered from the Fry Canyon PRB were comparable to laboratory samples in the presence of dissolved carbonate where U(VI) sorption occurred by surface complexation. Our findings demonstrate that uranium uptake by bone apatite will probably occur by surface complexation instead of precipitation of uranyl phosphate phases under the groundwater conditions found at many U-contaminated sites.

Real-Time X-ray Radiography Diagnostics of Components in Solid Rocket Motors

NASA Technical Reports Server (NTRS)

Cortopassi, A. C.; Martin, H. T.; Boyer, E.; Kuo, K. K.

2012-01-01

Solid rocket motors (SRMs) typically use nozzle materials which are required to maintain their shape as well as insulate the underlying support structure during the motor operation. In addition, SRMs need internal insulation materials to protect the motor case from the harsh environment resulting from the combustion of solid propellant. In the nozzle, typical materials consist of high density graphite, carbon-carbon composites and carbon phenolic composites. Internal insulation of the motor cases is typically a composite material with carbon, asbestos, Kevlar, or silica fibers in an ablative matrix such as EPDM or NBR. For both nozzle and internal insulation materials, the charring process occurs when the hot combustion products heat the material intensely. The pyrolysis of the matrix material takes away a portion of the thermal energy near the wall surface and leaves behind a char layer. The fiber reinforcement retains the porous char layer which provides continued thermal protection from the hot combustion products. It is of great interest to characterize both the total erosion rates of the material and the char layer thickness. By better understanding of the erosion process for a particular ablative material in a specific flow environment, the required insulation material thickness can be properly selected. The recession rates of internal insulation and nozzle materials of SRMs are typically determined by testing in some sort of simulated environment; either arc-jet testing, flame torch testing, or subscale SRMs of different size. Material recession rates are deduced by comparison of pre- and post-test measurements and then averaging over the duration of the test. However, these averaging techniques cannot be used to determine the instantaneous recession rates of the material. Knowledge of the variation in recession rates in response to the instantaneous flow conditions during the motor operation is of great importance. For example, in many SRM configurations the recession of the solid propellant grain can drastically alter the flow-field and effect the recession of internal insulation and nozzle materials. Simultaneous measurement of the overall erosion rate, the development of the char layer, and the recession of the char-virgin interface during the motor operation can be rather difficult. While invasive techniques have been used with limited success, they have serious drawbacks. Break wires or make wire sensors can be installed into a sufficient number of locations in the charring material from which a time history of the charring surface can be deduced. These sensors fundamentally alter the local structure of the material in which they are imbedded. Also, the location of these sensors within the material is not known precisely without the use of an X-ray. To determine instantaneous recession rates, real-time X-ray radiography (X-ray RTR) has been utilized in several SRM experiments at PSU. The X-ray RTR system discussed in this paper consists of an X-ray source, X-ray image intensifier, and CCD camera connected to a capture computer. The system has been used to examine the ablation process of internal insulation as well as nozzle material erosion in a subscale SRM. The X-ray source is rated to 320 kV at 10 mA and has both a large (5.5 mm) and small (3.0 mm) focal spot. The lead-lined cesium iodide X-ray image intensifier produces an image which is captured by a CCD camera with a 1,000 x 1,000 pixel resolution. To produce accurate imagery of the object of interest, the alignment of the X-ray source to the X-ray image intensifier is crucial. The image sequences captured during the operation of an SRM are then processed to enhance the quality of the images. This procedure allows for computer software to extract data on the total erosion rate and the char layer thickness. Figure 1 Error! Reference source not found.shows a sequence of images captured during the operation the subscale SRM with the X-ray RTR system. The X-rayTR system, alignment procedure, uncertainty determination, and image analysis process will be discussed in detail in the full manuscript.

Studies on biomass char gasification and dynamics

NASA Astrophysics Data System (ADS)

You, Zhanping; You, Shijun; Ma, Xiaoyan

2018-01-01

The gasification performances of two kinds of biomass char by experiment methods are studied, including conversion rate and gasification gas component with temperature and time. Experimental results show that gasification temperature has important effects on the conversion rate and gas component. In the range of experimental temperature, char conversion rates are no more than 30.0%. The apparent activation energies and apparent reaction frequency factors of two biomass chars are obtained through kinetic studies.

Adsorption mechanism for xanthene dyes to cellulose granules.

PubMed

Tabara, Aya; Yamane, Chihiro; Seguchi, Masaharu

2012-01-01

The xanthene dyes, erythrosine, phloxine, and rose bengal, were adsorbed to charred cellulose granules. The charred cellulose granules were preliminarily steeped in ionic (NaOH, NaCl, KOH, KCl, and sodium dodecyl sulfate (SDS)), nonionic (glucose, sucrose, and ethanol), and amphipathic sucrose fatty acid ester (SFAE) solutions, and adsorption tests on the dye to the steeped and charred cellulose granules were conducted. Almost none of the dye was adsorbed when the solutions of ionic and amphipathic molecules were used, but were adsorbed in the case of steeping in the nonionic molecule solutions. Thin-layer chromatography (TLC) and the Fourier transform infra-red (FT-IR) profiles of SFAE which was adsorbed to the charred cellulose granules and extracted by ethyl ether suggested the presence of hydrophobic sites on the surface of the charred cellulose granules. We confirmed that the xanthene dyes could bind to the charred cellulose granules by ionic and hydrophobic bonds.

Tyre char preparation from waste tyre rubber for dye removal from effluents.

PubMed

Mui, Edward L K; Cheung, W H; McKay, Gordon

2010-03-15

A number of chars from waste tyre rubber were prepared by carbonisation at 673-1173 K. The effects of holding time, heating rate and particle size on the textural characteristics and elemental composition of the resultant chars were investigated. It was demonstrated that temperatures over 773 K did not have a significant improvement on the total surface area but resulted in lower char yields following increased aromatisation. Modelling of dye adsorption isotherms showed that the Redlich-Peterson expression yields the best-fit between experimental and predicted data. Furthermore, for a larger sized dye like Acid Yellow 117 (MW=848 g/mol), the amount adsorbed by the tyre char is not directly proportional to the total surface area when compared with a commercial carbon, revealing that factors other than total surface area are involved in the adsorption potential of the tyre chars. (c) 2009 Elsevier B.V. All rights reserved.

Low-calorie bread baked with charred cellulose granules and wheat flour to eliminate toxic xanthene food dye in the alimentary canal.

PubMed

Tabara, Aya; Yamane, Chihiro; Seguchi, Masaharu

2012-01-01

We baked low-calorie bread by mixing charred cellulose granules with wheat flour, using the charred cellulose granules to eliminate toxic xanthene food dyes contained in processed foods from the alimentary canal. The size of the charred cellulose granules played an important role in determining good breadmaking properties in respect of the bread height (mm) and specific volume (SV, cm3/g). Charred cellulose granules with a diameter above 270 μm were blended with wheat flour at 10% to obtain bread with a lower caloric content (1020 kcal/gram of bread) than the control bread (1126 kcal) made solely from wheat flour. The charred cellulose granules taken out from the bread adsorbed toxic xanthene food dyes at around pH 6.5, such that toxic food dyes taken into the alimentary canal were excreted in the feces with the non-digestible cellulose granules.

Influence of pressure on pyrolysis of black liquor: 2. Char yields and component release.

PubMed

Whitty, Kevin; Kullberg, Mika; Sorvari, Vesa; Backman, Rainer; Hupa, Mikko

2008-02-01

This is the second in a series of papers concerning the behavior of black liquor during pyrolysis at elevated pressures. Two industrial black liquors were pyrolyzed under pressurized conditions in two laboratory-scale devices, a pressurized single-particle reactor and a pressurized grid heater. Temperatures ranging between 650 and 1100 degrees C and pressures in the range 1-20 bar were studied. Char yields were calculated and based on analysis of some of the chars the fate of carbon, sodium, potassium and sulfur was determined as a function of pyrolysis pressure. At temperatures below 800 degrees C little variation in char yield was observed at different pressures. At higher temperatures char yield increased with pressure due to slower decomposition of sodium carbonate. For the same reason, sodium release decreased with pressure. Sulfur release, however, increased with pressure primarily because there was less opportunity for its capture in the less-swollen chars.

Structural evolution of maize stalk/char particles during pyrolysis.

PubMed

Fu, Peng; Hu, Song; Sun, Lushi; Xiang, Jun; Yang, Tao; Zhang, Anchao; Zhang, Junying

2009-10-01

The structural evolution characteristics of maize stalk/char particles during pyrolysis were investigated. The char was prepared by pyrolyzing at temperatures ranging from 200 to 900 degrees C. Maize stalk and chars were characterized by thermogravimetric analysis, ultimate analysis (TGA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), helium density measurement and N(2) adsorption/desorption method. The char yield decreased rapidly with increasing temperature until 400 degrees C. As temperature increased, the char became progressively more aromatic and carbonaceous. The hydroxyl, aliphatic C-H, carbonyl and olefinic C=C groups were lost at high temperatures. Below 500 degrees C, the removal of volatile matter made pore opening. High temperatures led to the occurrence of softening, melting, fusing and carbon structural ordering. The aromatization process started at approximately 350 degrees C and continued to higher temperatures. The shrinkage of carbon structure occurred above 500 degrees C, which was concurrent with the aromatization process.

Combustion properties, water absorption and grindability of raw/torrefied biomass pellets and Silantek coal

NASA Astrophysics Data System (ADS)

Matali, Sharmeela; Rahman, Norazah Abdul; Idris, Siti Shawaliah; Yaacob, Nurhafizah

2017-12-01

Torrefaction, also known as mild pyrolysis, is proven to convert raw biomass into a value-added energy commodity particularly for application in combustion and co-firing systems with improved storage and handling properties. This paper aims to compare the characteristics of Malaysian bituminous coal i.e. Silantek coal with raw and torrefied biomass pellet originated from oil palm frond and fast growing tree species, Leucaena Leucocephala. Biomass samples were initially torrefied at 300 °C for 60 minutes. Resulting torrefied biomass pellets were analysed using a number of standard fuel characterisation analyses i.e. elemental analysis, proximate analysis and calorific content (high heating values) experiments. Investigations on combustion characteristics via dynamic thermogravimetric analysis (TGA), grindability and moisture uptake tests were also performed on the torrefied biomass pellets. Better quality bio-chars were produced as compared to its raw forms and with optimal process conditions, torrefaction may potentially produces a solid fuel with combustion reactivity and porosity equivalent to raw biomass while having compatible energy density and grindability to coal.

Ignition propagation and heat effects of propellant chips embedded in castable inhibitor using a laser flux test bomb

NASA Technical Reports Server (NTRS)

Bolton, Douglas E., Jr.

1993-01-01

A castable inhibitor is applied to the aft face of the Space Shuttle Redesigned Solid Rocket Motor (RSRM) forward segment propellant grain to control propellant surface burn area. During fabrication, the propellant surface is trimmed prior to the inhibitor application. This produces a potential for small propellant chips to remain undetected on the propellant surface and contaminate the inhibitor during application. The concern was that undetected propellant chips in the inhibitor might provide a fuse path for premature propellant ignition underneath the inhibitor. To evaluate the fuse path potential, testing was performed on inhibitor samples with embedded propellant. The internal motor environment was simulated with a calibrated CO2 laser beam directed onto a sample which was placed in a 4100 kPa (600 psi) nitrogen pressurized bomb (laser bomb). The testing showed definitive results pertaining to fuse path formation. Embedded propellant chips did not autoignite until the receding heat affected inhibitor surface reached, or passed, the propellant chip. Samples with embedded propellant chips in alignment did not propagate ignition from one chip to another with separation distances as small as 0.010 cm(0.004 inc) and some as little as 0.0051 cm (0.002 in). Propellant chips with volumes approximately less than 0.025 cu cm (0.0015 cu in) (which did not propagate ignition) did not increase the inhibitor material decomposition depth more than the resulting void cavity of the burned out propellant chip. In addition, the depth of this void cavity did not increase until it was overtaken by the surrounding material decomposition depth. This was due, in part, to the retention of the protective inhibitor char layer. Samples with embedded propellant strings, whose thicknesses were below 0.023 cm (0.009 in), did not propagate ignition. Propellant string thicknesses above 0.038 cm (0.015 in) did propagate ignition. Test sample char and heat affected layer measurements and observations compared well with those from the Space Shuttle Solid Rocket Motor (SRM) Technical Evaluation Motor no. 9(TEM-9).

Integrated mild gasification processing at the Homer City Electric Power Generating Station site. Final report, July 1989--June 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Battista, J.J.; Zawadzki, E.A.

1993-07-01

A new process for the production of commercial grade coke, char, and carbon products has been evaluated by Penelec/NYSEG. The process, developed by Coal Technology Corporation, CTC, utilizes a unique screw reactor to produce a devolatilized char from a wide variety of coals for the production of commercial grade coke for use in blast furnaces, foundries, and other processes requiring high quality coke. This process is called the CTC Mild Gasification Process (MGP). The process economics are significantly enhanced by integrating the new technology into an existing power generating complex. Cost savings are realized by the coke producer, the cokemore » user, and the electric utility company. Site specific economic studies involving the Homer City Generating Station site in Western Pennsylvania, confirmed that an integrated MGP at the Homer City site, using coal fines produced at the Homer City Coal Preparation Plant, would reduce capital and operating costs significantly and would enable the HC Owners to eliminate thermal dryers, obtain low cost fuel in the form of combustible gases and liquids, and obtain lower cost replacement coal on the spot market. A previous report, identified as the Interim Report on the Project, details the technical and economic studies.« less

Landform position and charring conditions control decomposition of soil organic matter and pyrogenic carbon

NASA Astrophysics Data System (ADS)

Abney, R.; Jin, L.; Berhe, A. A.

2017-12-01

Wildfire is a significant global control on both ecosystem properties and biogeochemical cycling, and wildfires are projected to increase in both size and severity with continued climate change. Post-fire, charred biomass, or pyrogenic carbon, is left behind as a significant, relatively slow-cycling component of the soil organic matter pool. Pyrogenic carbon has a turnover time on the centennial scale, and previous research has demonstrated that it is highly susceptible to erosion. However, the interaction of the roles of landform position and combustion temperature remains unexplored. We collected live Pinus jeffreyi bark and charred it under combustion conditions at three temperatures (200°C, 350°C, and 500°C). The charred bark was mixed with soil collected from both eroding and depositional landform positions and incubated for six months. Throughout this incubation, microbial respiration was monitored via collection of CO2, and cumulative respiration was fitted using both single- and multi-pool exponential models. Overall, respiration was highest in soil and char mixtures in the depositional landform positions. Pyrogenic carbon concentrations, as determined by the Kurth Mackenzie Deluca method, declined only slightly in the 200°C char mixed with the depositional soil. Scanning electron microscopy images of the chars before and after incubation illustrate some incorporation of soil organic matter into the structures of the char, and some breakdown of the physical structures of the char. Altogether, the lower temperature chars mixed with the soil from the depositional landform position had the highest decomposition rates, which suggests the role that landform position may play on the stability of pyrogenic carbon at the landscape scale. Furthermore, this implies that the post-fire erosional re-distribution of pyrogenic carbon may act as a significant control of its long-term stabilization in soil and landscape-scale soil carbon stocks.

Ultrasonically assisted extraction of calcium and ash from char

NASA Astrophysics Data System (ADS)

Mathumba, E. E.; Mbaya, R. K. K.; Kolesnikov, A.

2018-03-01

This study characterized and removed calcium and ash content from char to improve the chemical quality of char as reductant for titanium smelting application. Calcium in char can be classified in two parts: mineral matter and cationic metals associated with organic matrix. Virgin and chemically treated char was characterized by using ISO 1171, wet chemistry methods, ISO 19579, XRF, and B.E.T. methods. In this present work, demineralization of char with mild chemical leachants such as acetic acid, citric acid, gluconic acid and Ethylene Diamine Tetra Acetic acid with three different ultrasonic power input (150 W, 270 W and 300 W) and semi-dual frequency of 40 kHz tank was investigated. Actual power dissipated into the system was calculated from the calorimetric measurement. An optimum set of process parameters are identified and validated. The ultrasound technology was compared with soaking technology to determine the efficiency of ultrasound system for the removal of calcium. The removal of calcium was exponentially higher with ultrasonic treatment than without it. Results revealed that mild chemical reagents do not harm the carbon content of char. It is evident from the results that amongst the leachants used; acetic and citric acid has caused significant removal of mineral phases.

Fracture in Phenolic Impregnated Carbon Ablator

NASA Technical Reports Server (NTRS)

Agrawal, Parul; Chavez-Garcia, Jose F.

2011-01-01

The thermal protection materials used for spacecraft heat shields are subjected to various thermal-mechanical loads during an atmospheric reentry which can threaten the structural integrity of the system. This paper discusses the development of a novel technique to understand the failure mechanisms inside the thermal protection material, Phenolic Impregnated Carbon Ablator (PICA). PICA has successfully flown on the Stardust spacecraft and was the TPS material chosen for the Mars Science Laboratory (MSL), that will fly in 2011. Although PICA has good thermal properties, structurally, it is a weak material. To thoroughly understand failure in PICA, experiments were performed using FiberForm(Registered TradeMark) (precursor of PICA), virgin and furnace-charred PICA. Several small samples were tested inside an electron microscope to investigate the failure mechanisms. Micrographs were obtained before and after the failure in order to study crack initiation and growth. Videos were obtained to capture failure mechanisms in real time. Stress-strain data was obtained simultaneously for all the samples with the help of a data acquisition system, integrated to the mechanical stages. It was found that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred PICA, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred PICA showed greater strength values compared to FiberForm coupons, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Gasification reactor engineering approach to understanding the formation of biochar properties

PubMed Central

2016-01-01

The correlation between thermochemical provenance and biochar functionality is poorly understood. To this end, operational reactor temperatures (spanning the reduction zone), pressure and product gas composition measurements were obtained from a downdraft gasifier and compared against elemental composition, surface morphology and polyaromatic hydrocarbon content (PAH) of the char produced. Pine feedstock moisture with values of 7% and 17% was the experimental variable. Moderately high steady-state temperatures were observed inside the reactor, with a ca 50°C difference in how the gasifier operated between the two feedstock types. Both chars exhibited surface properties comparable to activated carbon, but the relatively small differences in temperature caused significant variations in biochar surface area and morphology: micropore area 584 against 360 m2 g−1, and micropore volume 0.287 against 0.172 cm3 g−1. Differences in char extractable PAH content were also observed, with higher concentrations (187 µg g−1 ± 18 compared with 89 ± 19 µg g−1 Σ16EPA PAH) when the gasifier was operated with higher moisture content feedstock. It is recommended that greater detail on operational conditions during biochar production should be incorporated to future biochar characterization research as a consequence of these results. PMID:27616911

Distillation of granulated scrap tires in a pilot plant.

PubMed

López, Félix A; Centeno, Teresa A; Alguacil, Francisco José; Lobato, Belén

2011-06-15

This paper reports the pyrolytic treatment of granulated scrap tires (GST) in a pilot distillation unit at moderate temperature (550°C) and atmospheric pressure, to produce oil, char and gas products. Tire-derived oil is a complex mixture of organic C(5)-C(24) compounds, including a very large proportion of aromatic compounds. This oil has a high gross calorific value (∼ 43 MJ kg(-1)) and N and S contents of 0.4% and 0.6%, respectively, falling within the specifications of certain heating fuels. The distillation gas is composed of hydrocarbons; methane and n-butane are the most abundant, investing the distillation gas with a very high gross calorific value (∼ 68 MJ Nm(-3)). This gas is transformed into electric power by a co-generation turbine. The distillation char is mostly made of carbon but with significant inorganic impurities (∼ 12 wt%). The quality of the solid residue of the process is comparable to that of some commercial chars. The quantity of residual solids, and the qualities of the gas, liquid and solid fractions, are similar to those obtained by conventional pyrolytic treatments of waste tires. However, the simplicity of the proposed technology and its low investment costs make it a very attractive alternative. Copyright © 2011 Elsevier B.V. All rights reserved.

Ablation characteristics and reaction mechanism of insulation materials under slag deposition condition

NASA Astrophysics Data System (ADS)

Guan, Yiwen; Li, Jiang; Liu, Yang

2017-07-01

Current understanding of the physical and chemical processes involved in the ablation of insulation materials by highly aluminized solid propellants is limited. The study on the heat transfer and ablation principle of ethylene propylene diene monomer (EPDM) materials under slag deposition condition is essential for future design or modification of large solid rocket motors (SRMs) for launch application. In this paper, the alumina liquid flow pattern and the deposition principle in full-scale SRM engines are discussed. The interaction mechanism between the alumina droplets and the wall are analyzed. Then, an experimental method was developed to simulate the insulation material ablation under slag deposition condition. Experimental study was conducted based on a laboratory-scale device. Meanwhile, from the analysis of the cross-sectional morphology and chemical composition of the charring layer after ablation, the reaction mechanism of the charring layer under deposition condition was discussed, and the main reaction equation was derived. The numerical simulation and experimental results show the following. (i) The alumina droplet flow in the deposition section of the laboratory-scale device is similar to that of a full-scale SRM. (ii) The charring layer of the EPDM insulator displays a porous tight/loose structure under high-temperature slag deposition condition. (iii) A seven-step carbothermal reduction in the alumina is derived and established under high-pressure and high-temperature environment in the SRM combustion chamber. (iv) The analysis using thermodynamic software indicates that the reaction of the alumina and charring layer initially forms Al4C3 during the operation. Then, Al element and Al2OC compound are subsequently produced with the reduction in the release of gas CO as well with continuous environmental heating.

Wildfires Caused by Formation of Small Impact Craters: A Kaali Crater Case

NASA Astrophysics Data System (ADS)

Losiak, Anna; Belcher, Claire; Hudspith, Victoria; Zhu, Menghua; Bronikowska, Malgorzata; Jõeleht, Argo; Plado, Juri

2016-04-01

Formation of ~200-km Chicxulub 65 Ma ago was associated with release of significant amount of thermal energy [1,2,3] which was sufficient to start wildfires that had either regional [4] or global [5] range. The evidence for wildfires caused by impacts smaller than Chicxulub is inconclusive. On one hand, no signs of fires are associated with the formation of 24-km Ries crater [6]. On the other hand, the Tunguska site was burned after the impact and the numerical models of the bolide-produced thermal radiation suggest that the Tunguska-like event would produce a thermal flux to the surface that is sufficient to ignite pine needles [7]. However, in case of Tunguska the only proof for the bolide starting the fire comes from an eyewitness description collected many years after the event. Some authors [8] suggest that this fire might have been caused "normaly" later during the same year, induced on dead trees killed by the Tunguska fall. More recently it was observed that the Chelyabinsk meteor [9] - smaller than Tunguska event - did not produced a fire. In order to explore this apparent relationship in more detail, we have studied the proximal ejecta from a 100-m in diameter, ~3500 years old [10] Kaali crater (Estonia) within which we find pieces of charred organic material. Those pieces appear to have been produced during the impact, according to their stratigraphic location and following 14C analysis [19] as opposed to pre- or post-impact forest fires. In order to determine the most probable formation mechanism of the charred organic material found within Kaali proximal ejecta blanket, we: 1) Analyzed charcoal under SEM to identify the charred plants and determine properties of the charcoal related to the temperature of its formation [11]. Detected homogenization of cell walls suggests that at least some pieces of charcoal were formed at >300 °C [11]. 2) Analyzed the reflectance properties of the charred particles in order to determine the intensity with which pyrolysis occurred [12,13]. Initial mesurements suggest some particles are partially charred. This may be consistent with a short thermal exposure. 3) Numerically estimated entry parameters and thermal radiation from the bolide that reaches the surface of the impact site. 4) Performed numerical modeling using iSALE of the Kaali crater formation and ejecta distribution, especially in terms of the temperature of the ejected particles [14]. References: [1] Melosh et al. 1990. Nature 343:251-254. [2] Shuvalov and Artemieva 2002. Geol. Soc. Am. Special Papers 356:695-703. [3] Goldin and Melosh 2009. Geology 37:1135-1138. [4] Belcher et al. 2015. J. Geolog. Soc. doi:10.1144/jgs2014-082. [5] Robertson et al. 2013. J. Geoph. Res. Biogeosc. 118:329-336. [6] Jones and Lim 2000. Paleogeog. Paleoclim.Paleoecol. 164:57-66. [7] Svetsov 2008. Catastrophic Events Caused by Cosmic Objects 207-226. [8] Jones. 2002. Paleogeog. Paleoclim.Paleoecol. 185:407-408. [9] Popowa et al. 2013. Science 342:1069-1073. [10] Losiak et al. 2016. MAPS (in press). [11] Scott 2000. Palaeoecol. 164:281-329. [12] Hudspith et al. 2014. Front Plant Sci. 5:714. [13] Hudspith et al. 2015. PloS One 10.1371/journal.pone.0120835. [14] Zhu et al. 2015. JGR:Planets 10.1002/2015JE004827.

Evaluation of the energy transfer in the char zone during ablation. Part 2: In-depth response of ablative composites, volume 1. Ph.D. Thesis, 1975. Final Report

NASA Technical Reports Server (NTRS)

Pike, R. W.; Delvalle, E. G.

1974-01-01

The decomposition of ablative composites is described along with the transport phenomena of pyrolysis gases which result from the decomposition of these plastics as they flow through the porous char of char-forming ablators. The pyrolysis products are those formed by the thermal degradation of nylon-phenolic resin and silicone elastomer composites. Emphasis is placed on the nature and extent of chemical reactions of the pyrolysis products and the char, along with the energy absorbed by the combined pyrolysis and char zone. Chemical reactions with thermodynamically consistent kinetic data are determined in order to develop a realistic analysis for predicting the thermal performance of ablative heat shields.

Nitric Oxide Reduction over Sewage Sludge and Coal Chars at Conditions Relevant to Staged Fluidized Bed Combustion

NASA Astrophysics Data System (ADS)

Salatino, P.; Solimene, R.; Chirone, R.

The de-NOx potential of coal and of dried and pelletized sewage sludge, a waste-derived fuel candidate for cofiring with coal, is assessed. The experimental procedure is based on operation of a bench scale fluidized bed reactor where NO-doped nitrogen is contacted with batches of the fuel. A second type of experiment has been purposely designed to assess the loss of reactivity of chars toward gasification by NOx as char is heat-treated for pre-set times at temperatures typical of fluidized bed combustion. A simple phenomenological model is developed to shed light on the basic features of the interaction between heterogeneous char-NOx reaction and thermal annealing of the char.

Pyrolysis of fast-growing aquatic biomass -Lemna minor (duckweed): Characterization of pyrolysis products.

PubMed

Muradov, Nazim; Fidalgo, Beatriz; Gujar, Amit C; T-Raissi, Ali

2010-11-01

The aim of this work was to conduct the experimental study of pyrolysis of fast-growing aquatic biomass -Lemna minor (commonly known as duckweed) with the emphasis on the characterization of main products of pyrolysis. The yields of pyrolysis gas, pyrolytic oil (bio-oil) and char were determined as a function of pyrolysis temperature and the sweep gas (Ar) flow rate. Thermogravimetric/differential thermogravimetric (TG/DTG) analyses of duckweed samples in inert (helium gas) and oxidative (air) atmosphere revealed differences in the TG/DTG patterns obtained for duckweed and typical plant biomass. The bio-oil samples produced by duckweed pyrolysis at different reaction conditions were analyzed using GC-MS technique. It was found that pyrolysis temperature had minor effect on the bio-oil product slate, but exerted major influence on the relative quantities of the individual pyrolysis products obtained. While, the residence time of the pyrolysis vapors had negligible effect on the yield and composition of the duckweed pyrolysis products. Copyright 2010 Elsevier Ltd. All rights reserved.

Material Science of Carbon

DTIC Science & Technology

2004-09-01

required for a specific application. The list of applications is very extensive and includes: aircraft brakes, electrodes, high temperature molds, rocket...and includes: aircraft brakes, electrodes, high temperature molds, rocket nozzles and exit cones, tires, ink, nuclear reactors and fuel particles...produced. For example carbons can be hard (chars) or soft (blacks), strong (PAN fibers) or weak ( aerogel ), stiff (pitch fibers) or flexible

THE OPTIMIZATION OF THERMAL OPTICAL ANALYSIS FOR THE MEASUREMENT OF BLACK CARBON IN REGIONAL PM2.5: A CHEMOMETRIC APPROACH REPORT

EPA Science Inventory

In thermal-optical analysis (TOA), particulate organic carbon (OC) as well as black carbon (BC) must be quantified. Both the BC that is native to the filter and instrument-produced OC char are products of incomplete combustion and have similar optical as well as chemical properti...

Effect of fire residues (ash and char) on microbial activity, respiration and methanogenesis in three subtropical wetland soils

NASA Astrophysics Data System (ADS)

Medvedeff, C.; Hogue, B.; Inglett, P.

2011-12-01

Prescribed fire is a common restoration and maintenance technique in the southern United States. Prescribed burns coupled with frequent natural fires in South Florida can have devastating effects on ecosystem function. To determine the effect fire residues have on carbon biogeochemical cycling litter material was obtained from two restored and one native marl wetland in Everglades National Park and manipulated in a laboratory setting to produce ash and vegetation derived char. Based on vegetation biomass removal pre and post fire (insitu) appropriate aliquots of each fire residue was added to experimental microcosms as a soil amendment. Soil enzymes (β-glucosidase, cellobiohydrolase, phosphatase, bis-phosphate and leucine amino peptidase), aerobic and anaerobic respiration (CO2) potentials, extractable C and methanogenesis were measured over a 25 day period. Regardless of site C enzymes responded to both amendments within 5 days of addition. Similarly amended soil contained more extractable carbon in the reference and one of the restored sites. In the restored sites ash and char inhibited methanogenesis, had no effect on anaerobic CO2 potentials, but stimulated aerobic respiration after ten days. In contrast, within the first ten days phosphatase enzyme activity was lower in the ash treatment when compared to the control treatment and stimulation of aerobic respiration was observed in both treatment soils. After ten days ash stimulated methanogenic processing while suppressing anaerobic CO2 production suggesting methanogens in this ecosystem may be dependant on usable carbon substrates derived from aerobic microbial processing. This study illustrates the variable response of C parameters to complete and incomplete combusted materials produced from both prescribed and natural fires with particular importance to fire adapted ecosystems.

Method and apparatus for removing coarse unentrained char particles from the second stage of a two-stage coal gasifier

DOEpatents

Donath, Ernest E.

1976-01-01

A method and apparatus for removing oversized, unentrained char particles from a two-stage coal gasification process so as to prevent clogging or plugging of the communicating passage between the two gasification stages. In the first stage of the process, recycled process char passes upwardly while reacting with steam and oxygen to yield a first stage synthesis gas containing hydrogen and oxides of carbon. In the second stage, the synthesis gas passes upwardly with coal and steam which react to yield partially gasified char entrained in a second stage product gas containing methane, hydrogen, and oxides of carbon. Agglomerated char particles, which result from caking coal particles in the second stage and are too heavy to be entrained in the second stage product gas, are removed through an outlet in the bottom of the second stage, the particles being separated from smaller char particles by a counter-current of steam injected into the outlet.

Kinetic modeling of the formation and growth of inorganic nano-particles during pulverized coal char combustion in O 2/N 2 and O 2/CO 2 atmospheres

DOE PAGES

Shaddix, Christopher R.; Niu, Yanqing; Hui, Shi'en; ...

2016-08-01

In this formation of nano-particles during coal char combustion, the vaporization of inorganic components in char and the subsequent homogeneous particle nucleation, heterogeneous condensation, coagulation, and coalescence play decisive roles. Furthermore, conventional measurements cannot provide detailed information on the dynamics of nano-particle formation and evolution, In this study, a sophisticated intrinsic char kinetics model that considers ash effects (including ash film formation, ash dilution, and ash vaporization acting in tandem), both oxidation and gasification by CO 2 and H 2O, homogeneous particle nucleation, heterogeneous vapor condensation, coagulation, and and coalescence mechanisms is developed and used to compare the temporal evolutionmore » of the number and size of nano-particles during coal char particle combustion as a function of char particle size, ash content, and oxygen content in O 2/N 2 and O 2/CO 2 atmospheres .« less

Kinetic modeling of the formation and growth of inorganic nano-particles during pulverized coal char combustion in O 2/N 2 and O 2/CO 2 atmospheres

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaddix, Christopher R.; Niu, Yanqing; Hui, Shi'en

In this formation of nano-particles during coal char combustion, the vaporization of inorganic components in char and the subsequent homogeneous particle nucleation, heterogeneous condensation, coagulation, and coalescence play decisive roles. Furthermore, conventional measurements cannot provide detailed information on the dynamics of nano-particle formation and evolution, In this study, a sophisticated intrinsic char kinetics model that considers ash effects (including ash film formation, ash dilution, and ash vaporization acting in tandem), both oxidation and gasification by CO 2 and H 2O, homogeneous particle nucleation, heterogeneous vapor condensation, coagulation, and and coalescence mechanisms is developed and used to compare the temporal evolutionmore » of the number and size of nano-particles during coal char particle combustion as a function of char particle size, ash content, and oxygen content in O 2/N 2 and O 2/CO 2 atmospheres .« less

Structural features of resorcinol-formaldehyde resin chars and interfacial behavior of water co-adsorbed with low-molecular weight organics

NASA Astrophysics Data System (ADS)

Gun'ko, Vladimir M.; Bogatyrov, Viktor M.; Turov, Vladimir V.; Leboda, Roman; Skubiszewska-Zięba, Jadwiga; Urubkov, Iliya V.

2013-10-01

Products of resorcinol-formaldehyde resin carbonization (chars) are characterized by different morphology (particle shape and sizes) and texture (specific surface area, pore volume and pore size distribution) depending on water content during resin polymerization. At a low amount of water (Cw = 37.8 wt.%) during synthesis resulting in strongly cross-linked polymers, carbonization gives nonporous particles. An increase in the water content to 62.7 wt.% results in a nano/mesoporous char, but if Cw = 73.3 wt.%, a char is purely nanoporous. Despite these textural differences, the Raman spectra of all the chars are similar because of the similarity in the structure of their carbon sheets with a significant contribution of sp3 C atoms. However, the difference in the spatial organization of the carbon sheet stacks in the particles results in the significant differences in the textural and morphological characteristics and in the adsorption properties of chars with respect to water, methane, benzene, hydrogen, methylene chloride, and dimethylsulfoxide.

Coal char oxidation kinetics in air medium

NASA Astrophysics Data System (ADS)

Slyusarskiy, K. V.; Jankovskiy, S. A.; Korotkikh, A. G.; Sorokin, I. V.

2017-01-01

Research on oxidation in air medium process of three different coal chars with various carbon content was presented. The anthracite, T-grade bituminous coal and 2B-grade lignite char powders with particle size less than 80 µm were studied. The coal char oxidation was studied by isothermal method using coupled TG-DSC analyzer Netzsch STA 449 Jupiter F3 in the temperature range 1000-1200 °C. Experiments were carried out at ambient pressure. Volumetric flow rate of oxidation medium into analyzer chamber was 250 ml/min and consisted of oxygen and argon with volumetric ratio 24:1. Based on experimental data, the average rate of carbon oxidation reaction values were defined at each temperature. Kinetic constants (frequency factor and activation energy) of reaction were defined as well via 1st order Arrhenius equation. Activation energy values are in good agreement with the data presented in the literature. Activation energy values for anthracite char are 1.6-1.7 times higher than those for bituminous coal and lignite chars, respectively.

Investigation on the fast co-pyrolysis of sewage sludge with biomass and the combustion reactivity of residual char.

PubMed

Deng, Shuanghui; Tan, Houzhang; Wang, Xuebin; Yang, Fuxin; Cao, Ruijie; Wang, Zhao; Ruan, Renhui

2017-09-01

Gaining the valuable fuels from sewage sludge is a promising method. In this work, the fast pyrolysis characteristics of sewage sludge (SS), wheat straw (WS) and their mixtures in different proportions were carried out in a drop-tube reactor. The combustion reactivity of the residual char obtained was investigated in a thermogravimetric analyzer (TGA). Results indicate that SS and WS at different pyrolysis temperatures yielded different characteristic gas compositions and product distributions. The co-pyrolysis of SS with WS showed that there existed a synergistic effect in terms of higher gas and bio-oil yields and lower char yield, especially at the WS adding percentage of 80wt%. The addition of WS to SS increased the carbon content in the SS char and improved char porous structures, resulting in an improvement in the combustion reactivity of the SS char. The research results can be used to promote co-utilization of sewage sludge and biomass. Copyright © 2017. Published by Elsevier Ltd.

Pyrolytic characteristics of biomass acid hydrolysis residue rich in lignin.

PubMed

Huang, Yanqin; Wei, Zhiguo; Yin, Xiuli; Wu, Chuangzhi

2012-01-01

Pyrolytic characteristics of acid hydrolysis residue (AHR) of corncob and pinewood (CAHR, WAHR) were investigated using a thermo-gravimetric analyzer (TGA) and a self-designed pyrolysis apparatus. Gasification reactivity of CAHR char was then examined using TGA and X-ray diffractometer. Result of TGA showed that thermal degradation curves of AHR descended smoothly along with temperature increasing from 150 °C to 850 °C, while a "sharp mass loss stage" for original biomass feedstock (OBF) was observed. Char yield from AHR (42.64-30.35 wt.%) was found to be much greater than that from OBF (26.4-19.15 wt.%). In addition, gasification reactivity of CAHR char was lower than that of corncob char, and there was big difference in micro-crystallite structure. It was also found that CAHR char reactivity decreased with pyrolysis temperature, but increased with pyrolysis heating rate and gasification temperature at 850-950 °C. Furthermore, CAHR char reactivity performed better under steam atmosphere than under CO2 atmosphere. Copyright © 2011 Elsevier Ltd. All rights reserved.

Techniques Suitable for a Portable Wear Metal Analyzer.

DTIC Science & Technology

1981-09-01

measured by a detector. Commonly used detectors are semiconductor detectors or proportional counters. b. Energy-Dispersive XRPS . In the energy-dispersive...because the sample must be charred before the analysis. C. X-Ray Fluorescence Spectroscopy. Normally the counting time for XRPS is 100 seconds

Chromatic variation of soot soiling: a possible marker for gunshot wounds in burnt bone.

PubMed

Amadasi, Alberto; Merli, Daniele; Brandone, Alberto; Cattaneo, Cristina

2014-01-01

Soot soiling is a crucial forensic parameter around gunshot lesions. Carbonization, however, can severely alter human tissues and mimic such clues. This study aims at evaluating the survival of soot soiling even after carbonization in bone. A total of 36 bovine ribs (half fleshed and half defleshed) were shot with two types of bullet (both 9-mm; full metal-jacketed and unjacketed) with a near-contact range. With unjacketed bullets, the shot left in every case a clear, black, and roughly round soot stain around the entrance wound, whereas full metal-jacketed bullets left no signs of soot. Every specimen then underwent calcination in an oven at 800°C. The analysis of the charred samples clearly showed the survival of the soot soiling in both fleshed and bony samples, with a clear correspondence with the former position, but with a different color (yellow). Thus, soot soiling may survive, although with a different color, even after charring. © 2013 American Academy of Forensic Sciences.

Global Kinetic Constants for Thermal Oxidative Degradation of a Cellulosic Paper

NASA Technical Reports Server (NTRS)

Kashiwagi, Takashi; Nambu, Hidesaburo

1992-01-01

Values of global kinetic constants for pyrolysis, thermal oxidative degradation, and char oxidation of a cellulosic paper were determined by a derivative thermal gravimetric study. The study was conducted at heating rates of 0.5, 1, 1.5, 3, and 5 C/min in ambient atmospheres of nitrogen, 0.28, 1.08, 5.2 percent oxygen concentrations, and air. Sample weight loss rate, concentrations of CO, CO2, and H2O in the degradation products, and oxygen consumption were continuously measured during the experiment. Values of activation energy, preexponential factor, orders of reaction, and yields of CO, CO2, H2O, total hydrocarbons, and char for each degradation reaction were derived from the results. Heat of reaction for each reaction was determined by differential scanning calorimetry. A comparison of the calculated CO, CO2, H2O, total hydrocarbons, sample weight loss rate, and oxygen consumption was made with the measured results using the derived kinetic constants, and the accuracy of the values of kinetic constants was discussed.

Maleimido substituted aromatic cyclotriphosphazenes

NASA Technical Reports Server (NTRS)

Kumar, D.; Fohlen, G. M.; Parker, J. A. (Inventor)

1985-01-01

4-Aminophenoxy cyclotriphosphazenes are reacted with maleic anhydride to produce maleamic acids which are converted to the maleimides. The maleimides are polymerized. By selection of starting materials (e.g., hexakis amino or trisaminophenoxy-trisphenoxy-cyclo-triphosphazenes), selection of molar proportions of reactants, use of mixtures of anhydrides and use of dianhydrides as bridging groups a variety of maleimides and polymers are produced. The polymers have high limiting oxygen indices, high char yields and other useful heat and fire resistant properties making them useful as, for example, impregnants of fabrics.

Aromatic cyclotriphosphazenes

NASA Technical Reports Server (NTRS)

Kamar, Devendra (Inventor); Fohlen, George M. (Inventor); Parker, John A. (Inventor)

1988-01-01

Four-Aminophenoxy cyclotriphosphazenes are reacted with maleic anhydride to produce maleamic acids which are converted to the maleimides. The maleimides are polymerized. By selection of starting materials (e.g., hexakis amino or trisaminophenoxy trisphenoxy cyclotrisphosphazenes), selection of molar porportions of reactants, use of mixtures of anhydrides and use of dianhydrides as bridging groups a variety of maleimides and polymers are produced. The polymers have high limiting oxygen indices, high char yields and other useful heat and fire resistant properties making them useful as, for example, impregnants of fabrics.

Influence of ultrasound pretreatment on wood physiochemical structure.

PubMed

He, Zhengbin; Wang, Zhenyu; Zhao, Zijian; Yi, Songlin; Mu, Jun; Wang, Xiaoxu

2017-01-01

As an initial step to increase the use of renewable biomass resources, this study was aimed at investigating the effects of ultrasound pretreatment on structural changes of wood. Samples were pretreated by ultrasound with the power of 300W and frequency of 28kHz in aqueous soda solution, aqueous acetic acid, or distilled water, then pretreated and control samples were characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). The results shown that ultrasound pretreatment is indeed effective in modifying the physiochemical structure of eucalyptus wood; the pretreatment decreased the quantity of alkali metals (e.g., potassium, calcium and magnesium) in the resulting material. Compared to the control group, the residual char content of samples pretreated in aqueous soda solution increased by 10.08%-20.12% and the reaction temperature decreased from 361°C to 341°C, however, in samples pretreated by ultrasound in acetic solution or distilled water, the residual char content decreased by 12.40%-21.45% and there were no significant differences in reactivity apart from a slightly higher maximum reaction rate. Ultrasound pretreatment increased the samples' crystallinity up to 35.5% and successfully removed cellulose, hemicellulose, and lignin from the samples; the pretreatment also increased the exposure of the sample to the treatment solutions, broke down sample pits, and generated collapses and microchannels on sample pits, and removed attachments in the samples. Copyright © 2016 Elsevier B.V. All rights reserved.

Thermal characteristics analysis of microwaves reactor for pyrolysis of used cooking oil

NASA Astrophysics Data System (ADS)

Anis, Samsudin; Shahadati, Laily; Sumbodo, Wirawan; Wahyudi

2017-03-01

The research is objected to develop microwave reactor for pyrolysis of used cooking oil. The effect of microwave power as well as addition of char as absorber towards its thermal characteristic were investigated. Domestic microwave was modified and used to test the thermal characteristic of used cooking oil in the terms of temperature evolution, heating rate, and thermal efficiency. The samples were examined under various microwave power of 347W, 399W, 572W and 642W for 25 minutes of irradiation time. The char loading was tested in the level of 0, 50, and 100 g. Microwave reactor consists of microwave unit with a maximum power of 642W, a ceramic reactor, and a condenser equipped with temperature measurement system was successfully developed. It was found that microwave power and addition of absorber significantly influenced the thermal characteristic of microwave reactor. Under investigated condition, the optimum result was obtained at microwave power of 642W and 100 g of char. The condition was able to provide temperature of 480°C, heating rate of 18.2°C/min and thermal efficiency of 53% that is suitable to pyrolyze used cooking oil.

Perfluorinated and polyfluorinated compounds in lake food webs from the Canadian high Arctic.

PubMed

Lescord, Gretchen L; Kidd, Karen A; De Silva, Amila O; Williamson, Mary; Spencer, Christine; Wang, Xiaowa; Muir, Derek C G

2015-03-03

Per- and polyfluorinated alkyl substances (PFASs) enter Arctic lakes through long-range atmospheric transport and local contamination, but their behavior in aquatic food webs at high latitudes is poorly understood. This study compared the concentrations of perfluorocarboxylates, perfluorosulfonates, and fluorotelomer sulfonates (FTS) in biotic and abiotic samples from six high Arctic lakes near Resolute Bay, Nunavut, Canada. Two of these lakes are known to be locally contaminated by a small airport and Arctic char (Salvelinus alpinus) from these lakes had over 100 times higher total [PFAS] when compared to fish from neighboring lakes. Perfluorononanoate (PFOA) and perfluorooctanesulfonate (PFOS) dominated in char, benthic chironomids (their main prey), and sediments, while pelagic zooplankton and water were dominated by lower chain acids and perfluorodecanesulfonate (PFDS). This study also provides the first measures of perfluoroethylcyclohexanesulfonate (PFECHS) and FTS compounds in water, sediment, juvenile char, and benthic invertebrates from lakes in the high Arctic. Negative relationships between [PFAS] and δ(15)N values (indicative of trophic position) within these food webs indicated no biomagnification. Overall, these results suggest that habitat use and local sources of contamination, but not trophic level, are important determinants of [PFAS] in biota from freshwater food webs in the Canadian Arctic.

Novel technologies to improve the performance of biomass pyrolsis systems

NASA Astrophysics Data System (ADS)

Liaw, Shi-Shen

Biomass pyrolysis is a thermochemical conversion process to convert lignocellosic materials into bio-oil, gas, and char. The bio-oil can be further refined to produce transportation fuels, high-value chemicals and heat. Although fast pyrolysis is a very promising technology for high bio-oil production yield, the reactors used have several technological problems that limit their future techno-economic viability. Current fast pyrolysis reactors use large quantities of carrier gas that reduce their thermal efficiency. The use of sand to accelerate heating rates results in serious attrition problems responsible for sand contamination of the bio-char produced. Most of the fast pyrolysis reactors currently used need to process very small particles which consume large quantities of energy in grinding. The bio-oil produced is also highly acidic and corrosive mainly due to the presence of acetic acid. The lack of a viable technology to use the acetic acid contained in these oils is a major challenge for the development of viable bio-oil refineries. The objective of this dissertation is to evaluate several technologies to improve the techno-economic viability of biomass pyrolysis systems. The main hypotheses of this dissertation are: (1) high yields of bio-oils could also be obtained by using auger pyrolysis reactors using very low volumes of carried gas and no sand as a heat carrier if the system is fed with very small particles (2) The grinding energy can be reduced if the biomass is torrefied. There are torrefaction conditions that will not affect the overall yield of pyrolysis products (3) Acetic acid produced during pyrolysis can be removed with the use of a fractional condensation system (4) The acids produced during the torrefaction and pyrolysis with the use of the fractional condensation system can be anaerobically digested to produce methane. In this dissertation, it was proved through Py-GC/MS studies that yield of most of the pyrolytic products can be explained by grouping them in five groups or families. The C1 family is formed by products of cellulose fragmentation reactions (glycoaldehyde, acetol, 1,2-ethanediol, monoacetate, butanedial). The products grouped in the C2 family (levoglucosan, levoglucosenone, 1,4:3,6-dianhydro-alpha-D-glucopyranose) are derived from cellulose depolymerization reactions. The molecules derived from hemicellulose (Acetic acid, furfural, 2-furanmethanol) were grouped in the H family. The products derived from lignin were grouped in two families L1 (derived from p-hydroxyl phenol (H) and guaiacyl (G) structures) and L2 (derived from syringyl (S) structures). The yield and properties of bio-oil obtained from an auger pyrolysis reactor is comparable with other existing fluidized bed reactors in the similar pyrolysis condition. The system proposed required much lower volumes of carrier gas and result in the production of a sand-free bio-char. It was also found that the reactions leadings to the formation of bio-char products and the yield of bio-oil are not affected if the pretreatment (torrefaction) temperature is maintained below 290 °C. Torrefaction at higher temperatures results in a dramatic reduction of the bio-oil yield and an increase in the bio-char yield. A condensation system coupled with the auger pyrolysis reactor was constructed and studied for the separation of crude bio-oil produced from Douglas Fir wood. As the first condenser temperature increases up to 80 °C, the content of light oxygenated organic compounds (chiefly the acetic acid and water) in the first condenser decreased significantly. For the first time, this dissertation reports the anaerobic digestion of the aqueous phase obtained in the thermal pretreatment (torrefaction) step and in the second condenser during biomass pyrolysis to produce bio-methane. Acid washing was studied to minimize the inhibitors (hydroxyacetaldehyde and monophenols) in aqueous phase for higher bio-methane production. The results of this dissertation confirm that with the implementation of the new technologies studied it is possible to improve the performance of existing fast pyrolysis systems.

Influence of crystal allomorph and crystallinity on the products and behavior of cellulose during fast pyrolysis

DOE PAGES

Mukarakate, Calvin; Mittal, Ashutosh; Ciesielski, Peter N.; ...

2016-07-19

Here, cellulose is the primary biopolymer responsible for maintaining the structural and mechanical integrity of cell walls and, during the fast pyrolysis of biomass, may be restricting cell wall expansion and inhibiting phase transitions that would otherwise facilitate efficient escape of pyrolysis products. Here, we test whether modifications in two physical properties of cellulose, its crystalline allomorph and degree of crystallinity, alter its performance during fast pyrolysis. We show that both crystal allomorph and relative crystallinity of cellulose impact the slate of primary products produced by fast pyrolysis. For both cellulose-I and cellulose-II, changes in crystallinity dramatically impact the fastmore » pyrolysis product portfolio. In both cases, only the most highly crystalline samples produced vapors dominated by levoglucosan. Cellulose-III, on the other hand, produces largely the same slate of products regardless of its relative crystallinity and produced as much or more levoglucosan at all crystallinity levels compared to cellulose-I or II. In addition to changes in products, the different cellulose allomorphs affected the viscoelastic properties of cellulose during rapid heating. Real-time hot-stage pyrolysis was used to visualize the transition of the solid material through a molten phase and particle shrinkage. SEM analysis of the chars revealed additional differences in viscoelastic properties and molten phase behavior impacted by cellulose crystallinity and allomorph. Regardless of relative crystallinity, the cellulose-III samples displayed the most obvious evidence of having transitioned through a molten phase.« less

Multiscale Architectures and Parallel Algorithms for Video Object Tracking

DTIC Science & Technology

2011-10-01

0 4 : if FIFO1 contains nDt frames then 5: Partition data into blocks. 6: Put SPE control block information...char buf 4 = FF; vec to r unsigned char buf 5 = FF; vec to r unsigned char buf 6 = FF; vec to r unsigned char buf 7 = FF; for ( j = 0 ; j < s i z e ; j...Public Release; Distribution Unlimited 8 7 u 6 ill :J (;) 5 E -;::; c 0 4 ~ u Q) X 3 Q) 8 7 6 u Q) Ul 5 :J (;) E :;::; 4 c 0

Conversion of microwave pyrolysed ASR's char using high temperature agents.

PubMed

Donaj, Pawel; Blasiak, Wlodzimierz; Yang, Weihong; Forsgren, Christer

2011-01-15

Pyrolysis enables to recover metals and organic feedstock from waste conglomerates such as: automotive shredder residue (ASR). ASR as well as its pyrolysis solid products, is a morphologically and chemically varied mixture, containing mineral materials, including hazardous heavy metals. The aim of the work is to generate fundamental knowledge on the conversion of the organic residues of the solid products after ASR's microwave pyrolysis, treated at various temperatures and with two different types of gasifying agent: pure steam or 3% (v/v) of oxygen. The research is conducted using a lab-scale, plug-flow gasifier, with an integrated scale for analysing mass loss changes over time of experiment, serving as macro TG at 950, 850 and 760 °C. The reaction rate of char decomposition was investigated, based on carbon conversion during gasification and pyrolysis stage. It was found in both fractions that char conversion rate decreases with the rise of external gas temperature, regardless of the gasifying agent. No significant differences between the reaction rates undergoing with steam and oxygen for char decomposition has been observed. This abnormal char behaviour might have been caused by the inhibiting effects of ash, especially alkali metals on char activity or due to deformation of char structure during microwave heating. Copyright © 2010 Elsevier B.V. All rights reserved.

Kinetic analysis of the interactions between calcium ferrite and coal char for chemical looping gasification applications: Identifying reduction routes and modes of oxygen transfer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riley, Jarrett; Siriwardane, Ranjani; Tian, Hanjing

Chemical Looping Gasification (CLG) is an emerging technology that shows promise for efficient coal gasification by eliminating the need for energy intensive gas separations to achieve a non-nitrogen diluted syngas stream. Oxygen from oxygen carriers, such as CaFe 2O 4, are used for coal gasification in place of conventionally produced gaseous oxygen from cryogenic separation of air. These oxygen carriers are unique for their ability to selectively oxidize coal to form syngas and show limited reactivity with syngas components (H 2, CO). To gain a deeper understanding of how these unique oxygen carriers perform and to offer a first attemptmore » at the reaction modeling of solid mediated interactions of this nature, this study was carried out to determine the kinetic parameters associated with the selective oxidation of coal derived char (Wyodak and Illinois #6) with a metal ferrite, CaFe 2O 4. Using thermogravimetric analysis (TGA) coupled with mass spectrometry, the selective oxygen release of metal ferrite in the presence of char by proximal contact was examined. The application of combinatory model fitting approaches was used to describe controlling resistances during oxygen release. A combination of the modified shrinking core model (SCM) with planar oxygen ion diffusion control and reaction order based models was used for kinetic parameter determination. CaFe 2O 4 particle size plays a major role in the prevailing mode of oxygen release. Particle sizes on the order of 40–50 μm tend to favor first order kinetically controlled regimes independent of geometric and diffusion controls. The probability for oxygen ion diffusion controlling regimes increased when the particle size range of the oxygen carrier was increased up to 350 μm. Char type also impacted the prevalence of the controlling regime. Higher ranked chars react in a slower manner, limiting the gradient for oxygen ion release from the oxygen carrier. Activation energies determined for this process range from 120–200kJ/mol and oxygen ion diffusion coefficients are on the order of 10-8 cm 2/s. It is suggested that oxygen ion movement is regulated by lattice diffusion out of partially reduced phases (Ca 2Fe 2O 5) and through reduced outer layers composed of CaO and Fe. The controlled movement of oxygen ions influences the rate of carbon oxidation in the char and therefore the selectivity towards partial oxidation products, which are desirable in CLG applications.« less

Kinetic analysis of the interactions between calcium ferrite and coal char for chemical looping gasification applications: Identifying reduction routes and modes of oxygen transfer

DOE PAGES

Riley, Jarrett; Siriwardane, Ranjani; Tian, Hanjing; ...

2017-05-20

Chemical Looping Gasification (CLG) is an emerging technology that shows promise for efficient coal gasification by eliminating the need for energy intensive gas separations to achieve a non-nitrogen diluted syngas stream. Oxygen from oxygen carriers, such as CaFe 2O 4, are used for coal gasification in place of conventionally produced gaseous oxygen from cryogenic separation of air. These oxygen carriers are unique for their ability to selectively oxidize coal to form syngas and show limited reactivity with syngas components (H 2, CO). To gain a deeper understanding of how these unique oxygen carriers perform and to offer a first attemptmore » at the reaction modeling of solid mediated interactions of this nature, this study was carried out to determine the kinetic parameters associated with the selective oxidation of coal derived char (Wyodak and Illinois #6) with a metal ferrite, CaFe 2O 4. Using thermogravimetric analysis (TGA) coupled with mass spectrometry, the selective oxygen release of metal ferrite in the presence of char by proximal contact was examined. The application of combinatory model fitting approaches was used to describe controlling resistances during oxygen release. A combination of the modified shrinking core model (SCM) with planar oxygen ion diffusion control and reaction order based models was used for kinetic parameter determination. CaFe 2O 4 particle size plays a major role in the prevailing mode of oxygen release. Particle sizes on the order of 40–50 μm tend to favor first order kinetically controlled regimes independent of geometric and diffusion controls. The probability for oxygen ion diffusion controlling regimes increased when the particle size range of the oxygen carrier was increased up to 350 μm. Char type also impacted the prevalence of the controlling regime. Higher ranked chars react in a slower manner, limiting the gradient for oxygen ion release from the oxygen carrier. Activation energies determined for this process range from 120–200kJ/mol and oxygen ion diffusion coefficients are on the order of 10-8 cm 2/s. It is suggested that oxygen ion movement is regulated by lattice diffusion out of partially reduced phases (Ca 2Fe 2O 5) and through reduced outer layers composed of CaO and Fe. The controlled movement of oxygen ions influences the rate of carbon oxidation in the char and therefore the selectivity towards partial oxidation products, which are desirable in CLG applications.« less

Solid fuel volatilization to produce synthesis gas

DOEpatents

Schmidt, Lanny D.; Dauenhauer, Paul J.; Degenstein, Nick J.; Dreyer, Brandon J.; Colby, Joshua L.

2014-07-29

A method comprising contacting a carbon and hydrogen-containing solid fuel and a metal-based catalyst in the presence of oxygen to produce hydrogen gas and carbon monoxide gas, wherein the contacting occurs at a temperature sufficiently high to prevent char formation in an amount capable of stopping production of the hydrogen gas and the carbon monoxide gas is provided. In one embodiment, the metal-based catalyst comprises a rhodium-cerium catalyst. Embodiments further include a system for producing syngas. The systems and methods described herein provide shorter residence time and high selectivity for hydrogen and carbon monoxide.

Properties and potential environmental applications of carbon adsorbents from waste tire rubber

USGS Publications Warehouse

Lehmann, C.M.B.; Rameriz, D.; Rood, M.J.; Rostam-Abadi, M.

2000-01-01

The properties of tire-derived carbon adsorbents (TDCA) produced from select tire chars were compared with those derived from an Illinois coal and pistachio nut shells. Chemical analyses of the TDCA indicated that these materials contain metallic elements not present in coal-and nut shell-derived carbons. These metals, introduced during the production of tire rubber, potentially catalyze steam gasification reactions of tire char. TDCA carbons contained larger meso-and macopore volumes than their counterparts derived from coal and nut shell (on the moisture-and ash-free-basis). Adsorptive properties of the tire-derived adsorbent carbons for air separation, gas storage, and gas clean up were also evaluated and compared with those of the coal-and nut shell derived carbons as well as a commercial activated carbon. The results revealed that TDCA carbons are suitable adsorbents for removing vapor-phase mercury from combustion flue gases and hazardous organic compounds from industrial gas streams.

Final Report

NASA Technical Reports Server (NTRS)

1995-01-01

This cooperative agreement explored the novel polymerization of vinylsilane, alone and in combination with other alkenylsilanes, alkylsilanes, and/or crosslinking agents, using dimethyltitanocene as homogeneous catalyst. The reactions were found to be initiated photochemically under mild conditions, and no hydrogen gas was evolved when alkenylsilanes were polymerized. The polymers were found to have predominately a carbosilane-type backbone containing -SiH2-CH2-CH2-Si and -SiH2-CH(CH3)-Si type linkages. The mechanism of polymerization was found to be step-growth. Despite the relatively low molecular weight of the polymer (M(sub n) - 500 and M(sub W) - 1500), pyrolysis resulted in conversion to C-rich SiC ceramic in high char yields (-60%). Copolymerization with methylsilane resulted in higher chars and more crystalline polymer. Addition of crosslinking agents such as polybutadiene or methyltrivinylsilane increased the viscosity of the polymer produced and enabled application as coatings to fiber toes.

Synergistic combination of biomass torrefaction and co-gasification: Reactivity studies.

PubMed

Zhang, Yan; Geng, Ping; Liu, Rui

2017-12-01

Two typical biomass feedstocks obtained from woody wastes and agricultural residues were torrefied or mildly pyrolized in a fixed-bed reactor. Effects of the torrefaction conditions on product distributions, compositional and energetic properties of the solid products, char gasification reactivity, and co-gasification behavior between coal and torrefied solids were systematically investigated. Torrefaction pretreatment produced high quality bio-solids with not only increased energy density, but also concentrated alkali and alkaline earth metals (AAEM). As a consequence of greater retention of catalytic elements in the solid products, the chars derived from torrefied biomass exhibited a faster conversion than those derived from raw biomass during CO 2 gasification. Furthermore, co-gasification of coal/torrefied biomass blends exhibited stronger synergy compared to the coal/raw biomass blends. The results and insights provided by this study filled a gap in understanding synergy during co-gasification of coal and torrefied biomass. Copyright © 2017 Elsevier Ltd. All rights reserved.

Solid-shape energy fuels from recyclable municipal solid waste and plastics

NASA Astrophysics Data System (ADS)

Gug, Jeongin

Diversion of waste streams, such as plastics, wood and paper, from municipal landfills and extraction of useful materials from landfills is an area of increasing interest across the country, especially in densely populated areas. One promising technology for recycling MSW (municipal solid waste) is to burn the high energy content components in standard coal boilers. This research seeks to reform wastes into briquette that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, moisture resistance, and retain high fuel value. Household waste with high paper and fibers content was used as the base material for this study. It was combined with recyclable plastics such as PE, PP, PET and PS for enhanced binding and energy efficiency. Fuel pellets were processed using a compression molding technique. The resulting moisture absorption, proximate analysis from burning, and mechanical properties were investigated after sample production and then compared with reference data for commercial coals and biomass briquettes. The effects of moisture content, compression pressure and processing temperature were studied to identify the optimal processing conditions with water uptake tests for the durability of samples under humid conditions and burning tests to examine the composition of samples. Lastly, mechanical testing revealed the structural stability of solid fuels. The properties of fuel briquettes produced from waste and recycled plastics improved with higher processing temperature but without charring the material. Optimization of moisture content and removal of air bubbles increased the density, stability and mechanical strength. The sample composition was found to be more similar to biomass fuels than coals because the majority of the starting material was paper-based solid waste. According to the proximate analysis results, the waste fuels can be expected to have low temperature ignition, less char formation and reduced CO2 emission with the high heating energy value similar to coal. It is concluded that solid fuels from paper based waste and plastics can be a good energy resource as an alternative and sustainable fuel, which may help to alleviate the environmental problems related to landfill space at the same time.

Distinct oxidative stabilities of char versus soot black carbon: Implications for quantification and environmental recalcitrance

NASA Astrophysics Data System (ADS)

Elmquist, Marie; Cornelissen, Gerard; Kukulska, Zofia; Gustafsson, Örjan

2006-06-01

Sequestration in sediments of black carbon (BC) from vegetation fires and fuel combustion may constitute a significant sink of otherwise rapidly cycling carbon from the atmosphere-biosphere cycle. It also has the potential to provide a historical record of atmospheric BC loadings. Previous treatments of BC as one homogeneous entity are being replaced with the growing awareness of a BC combustion continuum, a range spanning from slightly charred biomass to soot and graphite. Here the relative recalcitrance of different BC forms is evaluated, and implications for both BC quantification and environmental stability are considered. The stabilities of four BC reference materials against thermal oxidation in air were quite distinct with T50%BC values (i.e., the temperature where 50% BC remained in the residue) of 444°C (diesel soot-BC), 388°C (n-hexane soot-BC), 338°C (wood char-BC), and 266°C (grass char-BC). The implications for BC quantification have been illustrated for a thermal oxidation (the CTO-375) method commonly applied to study BC in sediments. This technique measured BC:TOC ratios of 78.3 ± 1.3% for the diesel soot-BC and 45.3 ± 6.1% for n-hexane soot-BC, whereas no CTO375-BC was detected for the two analyzed char-BC materials. The greater lability of char-BC compared to soot-BC likely reflects higher accessibility to internal microporosity in char-BC, facilitating internal O2 transfer. Decreasing the temperature cutoff below 375°C to also include char-BC is not possible as thermograms of nonpyrogenic reference materials indicated that such material would then be artifactually quantified as BC. The presence of mineral oxides in the sediment matrix may lead to a catalytically mediated lowering of the activation energy for soot-BC oxidation but not for char-BC or nonpyrogenic organic material. Several recent studies combine to challenge the proposition of complete recalcitrance of BC. Particularly, the thermal lability of char-BC from grassland fires deserves further attention in order to improve the understanding of BC in the global carbon cycle.

Lead sorption characteristics of various chicken bone part-derived chars.

PubMed

Park, Jong-Hwan; Wang, Jim J; Kim, Seong-Heon; Kang, Se-Won; Cho, Ju-Sik; Delaune, Ronald D; Ok, Yong Sik; Seo, Dong-Cheol

2018-01-18

Recycling food waste for beneficial use is becoming increasingly important in resource-limited economy. In this study, waste chicken bones of different parts from restaurant industry were pyrolyzed at 600 °C and evaluated for char physicochemical properties and Pb sorption characteristics. Lead adsorption isotherms by different chicken bone chars were carried out with initial Pb concentration range of 1-1000 mg L -1 at pH 5. The Pb adsorption data were better described by the Langmuir model (R 2  = 0.9289-0.9937; ARE = 22.7-29.3%) than the Freundlich model (R 2  = 0.8684-0.9544; ARE = 35.4-72.0%). Among the chars derived from different chicken bone parts, the tibia bone char exhibited the highest maximum Pb adsorption capacity of 263 mg g -1 followed by the pelvis (222 mg g -1 ), ribs (208 mg g -1 ), clavicle (179 mg g -1 ), vertebrae (159 mg g -1 ), and humerus (135 mg g -1 ). The Pb adsorption capacities were significantly and positively correlated with the surface area, phosphate release amount, and total phosphorus content of chicken bone chars (r ≥ 0.9711). On the other hand, approximately 75-88% of the adsorbed Pb on the chicken bone chars was desorbable with 0.1 M HCl, indicating their recyclability for reuse. Results demonstrated that chicken bone char could be used as an effective adsorbent for Pb removal in wastewater.

Removal of hexavalent Cr by coconut coir and derived chars--the effect of surface functionality.

PubMed

Shen, Ying-Shuian; Wang, Shan-Li; Tzou, Yu-Min; Yan, Ya-Yi; Kuan, Wen-Hui

2012-01-01

The Cr(VI) removal by coconut coir (CC) and chars obtained at various pyrolysis temperatures were evaluated. Increasing the pyrolysis temperature resulted in an increased surface area of the chars, while the corresponding content of oxygen-containing functional groups of the chars decreased. The Cr(VI) removal by CC and CC-derived chars was primarily attributed to the reduction of Cr(VI) to Cr(III) by the materials and the extent and rate of the Cr(VI) reduction were determined by the oxygen-containing functional groups in the materials. The contribution of pure Cr(VI) adsorption to the overall Cr(VI) removal became relatively significant for the chars obtained at higher temperatures. Accordingly, to develop a cost-effective method for removing Cr(VI) from water, the original CC is more advantageous than the carbonaceous counterparts because no pyrolysis is required for the application and CC has a higher content of functional groups for reducing Cr(VI) to less toxic Cr(III). Copyright © 2011 Elsevier Ltd. All rights reserved.

Mechanistic understanding of tetracycline sorption on waste tire powder and its chars as affected by Cu(2+) and pH.

PubMed

Lian, Fei; Song, Zhengguo; Liu, Zhongqi; Zhu, Lingyan; Xing, Baoshan

2013-07-01

The sorption characteristics of tetracycline (TC) by waste tire powder and its chars were investigated to explore the potential of using waste tires as effective sorbents for removal of TC from aqueous solution. Naphthalene (NAPH), a typical hydrophobic organic compound, was selected as asorbate for comparison. TC displayed much lower sorption affinity to tire powder than NAPH. However, it exhibited similar adsorption affinity as NAPH on the pyrolyzed tire chars, which was mainly attributed to π-π electron-donor-acceptor interactions of TC with the graphite surface of chars. TC and Cu(2+) could mutually facilitate the sorption of each other on both tire powder and pyrolyzed chars in a wide pH range. This could be explained by the metallic complexation and/or surface-bridging mechanisms (i.e., Cu- or TC-bridging). However, Cu(2+) and NAPH depressed the sorption of each other on tire powder and displayed negligible impact to each other on the highly pyrolyzed chars. Copyright © 2013 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zia-ul-Mustafa, M., E-mail: engr.ziamustafa@gmail.com; Ahmad, Faiz; Megat-Yusoff, Puteri S. M.

In this study, intumescent fire retardant coatings (IFRC) were developed to investigate the synergistic effects of reinforced mica and wollastonite fillers based IFRC towards heat shielding, char expansion, char composition and char morphology. Ammonium poly-phosphate (APP) was used as acid source, expandable graphite (EG) as carbon source, melamine as blowing agent, boric acid as additive and Hardener H-2310 polyamide amine in bisphenol A epoxy resin BE-188(BPA) was used as curing agent. Bunsen burner fire test was used for thermal performance according to UL-94 for 1 h. Field Emission Scanning Electron Microscopy (FESEM) was used to observe char microstructure. X-Ray Diffraction (XRD)more » and Fourier transform infrared spectroscopy (FTIR) were used to analyse char composition. The results showed that addition of clay filler in IFRC enhanced the fire protection performance of intumescent coating. X-Ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) results showed the presence of boron phosphate, silicon phosphate oxide, aluminium borate in the char that improved the thermal performance of intumescent fire retardant coating (IFRC). Resultantly, the presence of these developed compounds enhanced the Integrity of structural steel upto 500°C.« less

Effects of various reactive gas atmospheres on the properties of bio-oil using microwave pyrolysis

USDA-ARS?s Scientific Manuscript database

Fast pyrolysis of lignocellulosic biomass produces organic liquids (bio-oil), bio-char, water, and non-condensable gases. The non-condensable gas component typically contains syngas (H2, CO and CO2) as well as small hydrocarbons (CH4, C2H6, and C3H8). Tail Gas Reactive Pyrolysis (TGRP), a patent p...

Production of activated carbon from TCR char

NASA Astrophysics Data System (ADS)

Stenzel, Fabian; Heberlein, Markus; Klinner, Tobias; Hornung, Andreas

2016-04-01

The utilization of char for adsorptive purposes is known since the 18th century. At that time the char was made of wood or bones and used for decoloration of fluids. In the 20th century the production of activated carbon in an industrial scale was started. The today's raw materials for activated carbon production are hard coal, peat, wood or coconut shells. All these materials entail costs especially the latter. Thus, the utilization of carbon rich residues (biomass) is an interesting economic opportunity because it is available for no costs or even can create income. The char is produced by thermo-catalytic reforming (TCR®). This process is a combination of an intermediate pyrolysis and subsequently a reforming step. During the pyrolysis step the material is decomposed in a vapor and a solid carbon enriched phase. In the second step the vapor and the solid phase get in an intensive contact and the quality of both materials is improved via the reforming process. Subsequently, the condensables are precipitated from the vapor phase and a permanent gas as well as oil is obtained. Both are suitable for heat and power production which is a clear advantage of the TCR® process. The obtained biochar from the TCR® process has special properties. This material has a very low hydrogen and oxygen content. Its stability is comparable to hard coal or anthracite. Therefore it consists almost only of carbon and ash. The latter depends from input material. Furthermore the surface structure and area can be influenced during the reforming step. Depending from temperature and residence time the number of micro pores and the surface area can be increased. Preliminary investigations with methylene blue solution have shown that a TCR® char made of digestate from anaerobic digestion has adsorptive properties. The decoloration of the solution was achieved. A further influencing factor of the adsorption performance is the particle size. Based on the results of the preliminary tests a systematically investigation was started. For this a muffle furnace with a maximum temperature up to 1300 ° C is used. Furthermore the gaseous atmosphere can be controlled. So it is possible to carry out the trials with the absence of oxygen by purging with nitrogen, carbon oxide and/ or steam for example. With the addition of steam the number of mesopores is increased. These pores are responsible for the adsorption performance in liquid phases. The trials for the TCR® chars made from beech wood (reference) and digestate are currently carried out. Additionally the reduction of the ash content of the char by using hydrochloric and acetic acid is investigated, too. These leaching tests are carried out in a lab scale test rig at an operating temperature of 60 ° C and a residence time up to 4 hours. The main objective is to adapt the TCR® process with regard to an optimized activated carbon production from biogenic residues to obtain an economic sustainable concept.

Controls upon biomass losses and char production from prescribed burning on UK moorland.

PubMed

Worrall, Fred; Clay, Gareth D; May, Richard

2013-05-15

Prescribed burning is a common management technique used across many areas of the UK uplands. However, there are few data sets that assess the loss of biomass during burning and even fewer data on the effect of burning on above-ground carbon stocks and production of char. During fire the production of char occurs which represents a transfer of carbon from the short term bio-atmospheric cycle to the longer term geological cycle. However, biomass is consumed leading to the reduction in litter formation which is the principal mechanism for peat formation. This study aims to solve the problem of whether loss of biomass during a fire is ever outweighed by the production of refractory forms of carbon during the fire. This study combines both a laboratory study of char production with an assessment of biomass loss from a series of field burns from moorland in the Peak District, UK. The laboratory results show that there are significant effects due to ambient temperature but the most important control on dry mass loss is the maximum burn temperature. Burn temperature was also found to be linearly related to the production of char in the burn products. Optimisation of dry mass loss, char production and carbon content shows that the production of char from certain fires could store more carbon in the ecosystem than if there had been no fire. Field results show that approximately 75% of the biomass and carbon were lost through combustion, a figure comparable to other studies of prescribed fire in other settings. Char-C production was approximately 2.6% of the carbon consumed during the fire. This study has shown that there are conditions (fast burns at high temperatures) under which prescribed fire may increase C sequestration through char production and that these conditions are within existing management options available to practitioners. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of fresh and aged chars from pyrolysis and hydrothermal carbonization on nutrient sorption in agricultural soils

NASA Astrophysics Data System (ADS)

Gronwald, M.; Don, A.; Tiemeyer, B.; Helfrich, M.

2015-06-01

Leaching of nutrients from agricultural soils causes major environmental problems that may be reduced with amendments of chars derived from pyrolysis (pyrochars) or hydrothermal carbonization (hydrochars). Chars are characterized by a high adsorption capacity - i.e. they may retain nutrients such as nitrate and ammonium. However, the physicochemical properties of the chars and hence their sorption capacity likely depend on feedstock and the production process. We investigated the nutrient retention capacity of pyrochars and hydrochars from three different feedstocks (digestates, Miscanthus, woodchips) mixed into different soil substrates (sandy loam and silty loam). Moreover, we investigated the influence of char degradation on its nutrient retention capacity using a 7-month in situ field incubation of pyrochar and hydrochar mixed into soils at three different field sites. Pyrochars showed the highest ability to retain nitrate, ammonium and phosphate, with pyrochar from woodchips being particularly efficient in nitrate adsorption. Ammonium adsorption of pyrochars was controlled by the soil type of the soil-char mixture. We found some ammonium retention on sandy soils, but no pyrochar effect or even ammonium leaching from the loamy soil. The phosphate retention capacity of pyrochars strongly depended on the pyrochar feedstock with large phosphate leaching from digestate-derived pyrochar and some adsorption capacity from woodchip-derived pyrochar. Application of hydrochars to agricultural soils caused small, and often not significant, effects on nutrient retention. In contrast, some hydrochars did increase the leaching of nutrients compared to the non-amended control soil. We found a surprisingly rapid loss of the chars' adsorption capacity after field application of the chars. For all sites and for hydrochar and pyrochar, the adsorption capacity was reduced by 60-80 % to less or no nitrate and ammonium adsorption. Thus, our results cast doubt on the efficiency of char applications to temperate zone soils to minimize nutrient losses via leaching.

Development, Verification and Validation of Enclosure Radiation Capabilities in the CHarring Ablator Response (CHAR) Code

NASA Technical Reports Server (NTRS)

Salazar, Giovanni; Droba, Justin C.; Oliver, Brandon; Amar, Adam J.

2016-01-01

With the recent development of multi-dimensional thermal protection system (TPS) material response codes including the capabilities to account for radiative heating is a requirement. This paper presents the recent efforts to implement such capabilities in the CHarring Ablator Response (CHAR) code developed at NASA's Johnson Space Center. This work also describes the different numerical methods implemented in the code to compute view factors for radiation problems involving multiple surfaces. Furthermore, verification and validation of the code's radiation capabilities are demonstrated by comparing solutions to analytical results, to other codes, and to radiant test data.

Thermochemical tests on resins: Char resistance of selected phenolic cured epoxides

NASA Technical Reports Server (NTRS)

Keck, F. L.

1982-01-01

Curing epoxy resins with novalac phenolic resins is a feasible approach for increasing intact char of the resin system. Char yields above 40% at 700 C were achieved with epoxy novalac (DEN 438)/novalac phenolic (BRWE 5833) resin systems with or without catalyst such as ethyl tri-phenyl phosphonium iodide. These char yields are comparable to commercially used epoxy resin systems like MY-720/DDS/BF3. Stable prepregs are easily made from a solvent solution of the epoxy/phenolic system and this provides a feasible process for fabrication of same into commercial laminates.

Effect of basalt fibres reinforcement and aluminum trihydrate on the thermal properties of intumescent fire retardant coatings

NASA Astrophysics Data System (ADS)

Yasir, Muhammad; Amir, Norlaili Binti; Ahmad, Faiz; Syahirah Rodzhan, N.

2017-08-01

This research is carried out in order to study the synergistic effect of aluminium trihydrate and basalt fibres on the properties of fire resistant intumescent coatings. Intumescent fire retardant coatings were developed using different flame retardants such as ammonium polyphosphate, expandable graphite, melamine and boric acid. These flame retardants were bound together with the help of epoxy binder along with curing agent. Furthermore, individual and combinations of aluminium trihydrate and basalt fibres was incorporated in the formulations to analyse mechanical and chemical properties of the coatings. Char expansion was observed using furnace test, thermogravimetric analysis was used to determine residual weight, X-Ray Diffraction was performed to investigate compounds present in the char, shear test was conducted to determine char strength and scanning electron microscopy analysis was performed to observe morphology of the burnt char. From the microscopic investigation it was concluded that the dense structure of the char increased the char integrity by adding basalt and aluminium trihydrate as fillers. X-Ray Diffraction results shows the presence boron phosphate, and boric acid which enhanced the thermal performance of the coating up to 800°C. From the Thermogravimetric analysis it was concluded that the residual weight of the char was increased up to 34.9 % for IC-B2A4 which enhanced thermal performance of intumescent coating.

Test and Analysis of Solid Rocket Motor Nozzle Ablative Materials

NASA Technical Reports Server (NTRS)

Clayton, J. Louie

2017-01-01

Asbestos free solid motor internal insulation samples were tested at the MSFC Hyperthermal Facility. Objectives of the test were to gather data for analog characterization of ablative and in-depth thermal performance of rubber materials subject to high enthalpy/pressure flow conditions. Tests were conducted over a range of convective heat fluxes for both inert and chemically reactive sub-sonic free stream gas flow. Instrumentation included use of total calorimeters, thermocouples, and a surface pyrometer for surface temperature measurement. Post-test sample forensics involved measurement of eroded depth, charred depth, total sample weight loss, and documentation of the general condition of the eroded profile. A complete Charring Material Ablator (CMA) style aero-thermal analysis was conducted for the test matrix and results compared to the measured data. In general, comparisons were possible for a number of the cases and the results show a limited predictive ability to model accurately both the ablative response and the in-depth temperature profiles. Lessons learned and modeling recommendations are made regarding future testing and modeling improvements that will increase understanding of the basic chemistry/physics associated with the complicated material ablation process of rubber materials.

Fast Pyrolysis Behavior of Banagrass as a Function of Temperature and Volatiles Residence Time in a Fluidized Bed Reactor

DOE PAGES

Morgan, Trevor James; Turn, Scott Q.; George, Anthe

2015-08-26

A reactor was designed and commissioned to study the fast pyrolysis behavior of banagrass as a function of temperature and volatiles residence time. Four temperatures between 400 and 600°C were examined as well as four residence times between ~1.0 and 10 seconds. Pyrolysis product distributions of bio-oil, char and permanent gases were determined at each reaction condition. The elemental composition of the bio-oils and chars was also assessed. The greatest bio-oil yield was recorded when working at 450°C with a volatiles residence time of 1.4 s, ~37 wt% relative to the dry ash free feedstock (excluding pyrolysis water). The amountsmore » of char (organic fraction) and permanent gases under these conditions are ~4 wt% and 8 wt% respectively. The bio-oil yield stated above is for 'dry' bio-oil after rotary evaporation to remove solvent, which results in volatiles and pyrolysis water being removed from the bio-oil. The material removed during drying accounts for the remainder of the pyrolysis products. The 'dry' bio-oil produced under these conditions contains ~56 wt% carbon which is ~40 wt% of the carbon present in the feedstock. The oxygen content of the 450°C, 1.4 s 'dry' bio-oil is ~38 wt%, which accounts for ~33 wt% of the oxygen in the feedstock. At higher temperature or longer residence time less bio-oil and char is recovered and more gas and light volatiles are produced. Increasing the temperature has a more significant effect on product yields and composition than increasing the volatiles residence time. At 600°C and a volatiles residence time of 1.2 seconds the bio-oil yield is ~21 wt% of the daf feedstock, with a carbon content of 64 wt% of the bio-oil. The bio-oil yield from banagrass is significantly lower than from woody biomass or grasses such as switchgrass or miscanthus, but is similar to barley straw. In conclusion, the reason for the low bio-oil yield from banagrass is thought to be related to its high ash content (8.5 wt% dry basis) and high concentration of alkali and alkali earth metals (totaling ~2.8 wt% relative to the dry feedstock) which are catalytic and increase cracking reactions during pyrolysis.« less

Fast Pyrolysis Behavior of Banagrass as a Function of Temperature and Volatiles Residence Time in a Fluidized Bed Reactor

PubMed Central

Morgan, Trevor James; Turn, Scott Q.; George, Anthe

2015-01-01

A reactor was designed and commissioned to study the fast pyrolysis behavior of banagrass as a function of temperature and volatiles residence time. Four temperatures between 400 and 600°C were examined as well as four residence times between ~1.0 and 10 seconds. Pyrolysis product distributions of bio-oil, char and permanent gases were determined at each reaction condition. The elemental composition of the bio-oils and chars was also assessed. The greatest bio-oil yield was recorded when working at 450°C with a volatiles residence time of 1.4 s, ~37 wt% relative to the dry ash free feedstock (excluding pyrolysis water). The amounts of char (organic fraction) and permanent gases under these conditions are ~4 wt% and 8 wt% respectively. The bio-oil yield stated above is for 'dry' bio-oil after rotary evaporation to remove solvent, which results in volatiles and pyrolysis water being removed from the bio-oil. The material removed during drying accounts for the remainder of the pyrolysis products. The 'dry' bio-oil produced under these conditions contains ~56 wt% carbon which is ~40 wt% of the carbon present in the feedstock. The oxygen content of the 450°C, 1.4 s 'dry' bio-oil is ~38 wt%, which accounts for ~33 wt% of the oxygen in the feedstock. At higher temperature or longer residence time less bio-oil and char is recovered and more gas and light volatiles are produced. Increasing the temperature has a more significant effect on product yields and composition than increasing the volatiles residence time. At 600°C and a volatiles residence time of 1.2 seconds the bio-oil yield is ~21 wt% of the daf feedstock, with a carbon content of 64 wt% of the bio-oil. The bio-oil yield from banagrass is significantly lower than from woody biomass or grasses such as switchgrass or miscanthus, but is similar to barley straw. The reason for the low bio-oil yield from banagrass is thought to be related to its high ash content (8.5 wt% dry basis) and high concentration of alkali and alkali earth metals (totaling ~2.8 wt% relative to the dry feedstock) which are catalytic and increase cracking reactions during pyrolysis. PMID:26308860

Fast Pyrolysis Behavior of Banagrass as a Function of Temperature and Volatiles Residence Time in a Fluidized Bed Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, Trevor James; Turn, Scott Q.; George, Anthe

A reactor was designed and commissioned to study the fast pyrolysis behavior of banagrass as a function of temperature and volatiles residence time. Four temperatures between 400 and 600°C were examined as well as four residence times between ~1.0 and 10 seconds. Pyrolysis product distributions of bio-oil, char and permanent gases were determined at each reaction condition. The elemental composition of the bio-oils and chars was also assessed. The greatest bio-oil yield was recorded when working at 450°C with a volatiles residence time of 1.4 s, ~37 wt% relative to the dry ash free feedstock (excluding pyrolysis water). The amountsmore » of char (organic fraction) and permanent gases under these conditions are ~4 wt% and 8 wt% respectively. The bio-oil yield stated above is for 'dry' bio-oil after rotary evaporation to remove solvent, which results in volatiles and pyrolysis water being removed from the bio-oil. The material removed during drying accounts for the remainder of the pyrolysis products. The 'dry' bio-oil produced under these conditions contains ~56 wt% carbon which is ~40 wt% of the carbon present in the feedstock. The oxygen content of the 450°C, 1.4 s 'dry' bio-oil is ~38 wt%, which accounts for ~33 wt% of the oxygen in the feedstock. At higher temperature or longer residence time less bio-oil and char is recovered and more gas and light volatiles are produced. Increasing the temperature has a more significant effect on product yields and composition than increasing the volatiles residence time. At 600°C and a volatiles residence time of 1.2 seconds the bio-oil yield is ~21 wt% of the daf feedstock, with a carbon content of 64 wt% of the bio-oil. The bio-oil yield from banagrass is significantly lower than from woody biomass or grasses such as switchgrass or miscanthus, but is similar to barley straw. In conclusion, the reason for the low bio-oil yield from banagrass is thought to be related to its high ash content (8.5 wt% dry basis) and high concentration of alkali and alkali earth metals (totaling ~2.8 wt% relative to the dry feedstock) which are catalytic and increase cracking reactions during pyrolysis.« less

Possibilities and limits of pyrolysis for recycling plastic rich waste streams rejected from phones recycling plants.

PubMed

Caballero, B M; de Marco, I; Adrados, A; López-Urionabarrenechea, A; Solar, J; Gastelu, N

2016-11-01

The possibilities and limits of pyrolysis as a means of recycling plastic rich fractions derived from discarded phones have been studied. Two plastic rich samples (⩾80wt% plastics) derived from landline and mobile phones provided by a Spanish recycling company, have been pyrolysed under N 2 in a 3.5dm 3 reactor at 500°C for 30min. The landline and mobile phones yielded 58 and 54.5wt% liquids, 16.7 and 12.6wt% gases and 28.3 and 32.4wt% solids respectively. The liquids were a complex mixture of organic products containing valuable chemicals (toluene, styrene, ethyl-benzene, etc.) and with high HHVs (34-38MJkg -1 ). The solids were composed of metals (mainly Cu, Zn, and Al) and char (≈50wt%). The gases consisted mainly of hydrocarbons and some CO, CO 2 and H 2 . The halogens (Cl, Br) of the original samples were mainly distributed between the gases and solids. The metals and char can be easily separated and the formers may be recycled, but the uses of the char will be restricted due to its Cl/Br content. The gases may provide the energy requirements of the processing plant, but HBr and HCl must be firstly eliminated. The liquids could have a potential use as energy or chemicals source, but the practical implementation of these applications will be no exempt of great problems that may become insurmountable (difficulty of economically recovering pure chemicals, contamination by volatile metals, etc.). Copyright © 2016 Elsevier Ltd. All rights reserved.

Apparatus for mixing char-ash into coal stream

DOEpatents

Blaskowski, Henry J.

1982-03-16

Apparatus for obtaining complete mixing of char with coal prior to the introduction of the mixture into the combustor (30) of a coal gasifier (10). The coal is carried in one air stream (22), and the char in another air stream (54), to a riffle plate arrangement (26), where the streams of solid are intimately mixed or blended.

Char syndrome: an additional family with polythelia, a new finding.

PubMed

Zannolli, R; Mostardini, R; Matera, M; Pucci, L; Gelb, B D; Morgese, G

2000-11-27

This report describes a father and daughter with Char syndrome, a rare autosomal dominant disorder. Both affected individuals had typical face, strabismus, and foot anomalies. The girl also had a patent ductus arteriosus. In addition, both patients had polythelia (supernumerary nipples), a finding not described before in the Char syndrome. Copyright 2000 Wiley-Liss, Inc.

Formation of nanocarbon spheres by thermal treatment of woody char from fast pyrolysis process

Treesearch

Qiangu Yan; Hossein Toghiani; Zhiyong Cai; Jilei Zhang

2014-01-01

Influences of thermal treatment conditions of temperature, reaction cycle and time, and purge gas type on nanocarbon formation over bio-chars from fast pyrolysis and effects of thermal reaction cycle and purge gas type on bio-char surface functional groups were investigated by temperature-programmed desorption (TPD) and temperature programmed reduction methods....

Near-extinction and final burnout in coal combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hurt, R.H.; Davis, K.A.

The late stages of char combustion have a special technological significance, as carbon conversions of 99% or greater are typically required for the economic operation of pulverized coal fired boilers. In the present article, two independent optical techniques are used to investigate near-extinction and final burnout phenomenas. Captive particle image sequences, combined with in situ optical measurements on entrained particles, provide dramatic illustration of the asymptotic nature of the char burnout process. Single particle combustion to complete burnout is seen to comprise two distinct stages: (1) a rapid high-temperature combustion stage, consuming about 70% of the char carbon and endingmore » with near-extinction of the heterogeneous reactions due to a loss of global particle reactivity, and (2) a final burnout stage occurring slowly at lower temperatures. For particles containing mineral matter, the second stage can be further subdivided into: (2a) late char combustion, which begins after the near-extinction event, and converts carbon-rich particles to mixed particle types at a lower temperature and a slower rate; and (2b) decarburization of ash -- the removal of residual carbon inclusions from inorganic (ash) frameworks in the very late stages of combustion. This latter process can be extremely slow, requiring over an order of magnitude more time than the primary rapid combustion stage. For particles with very little ash, the loss of global reactivity leading to early near-extinction is clearly related to changes in the carbonaceous char matrix, which evolves over the course of combustion. Current global kinetic models used for the prediction of char combustion rates and carbon burnout in boilers do not predict the asymptotic nature of char combustion. More realistic models accounting for the evolution of char structure are needed to make accurate predictions in the range of industrial interest.« less

Computational investigations of low-emission burner facilities for char gas burning in a power boiler

NASA Astrophysics Data System (ADS)

Roslyakov, P. V.; Morozov, I. V.; Zaychenko, M. N.; Sidorkin, V. T.

2016-04-01

Various variants for the structure of low-emission burner facilities, which are meant for char gas burning in an operating TP-101 boiler of the Estonia power plant, are considered. The planned increase in volumes of shale reprocessing and, correspondingly, a rise in char gas volumes cause the necessity in their cocombustion. In this connection, there was a need to develop a burner facility with a given capacity, which yields effective char gas burning with the fulfillment of reliability and environmental requirements. For this purpose, the burner structure base was based on the staging burning of fuel with the gas recirculation. As a result of the preliminary analysis of possible structure variants, three types of early well-operated burner facilities were chosen: vortex burner with the supply of recirculation gases into the secondary air, vortex burner with the baffle supply of recirculation gases between flows of the primary and secondary air, and burner facility with the vortex pilot burner. Optimum structural characteristics and operation parameters were determined using numerical experiments. These experiments using ANSYS CFX bundled software of computational hydrodynamics were carried out with simulation of mixing, ignition, and burning of char gas. Numerical experiments determined the structural and operation parameters, which gave effective char gas burning and corresponded to required environmental standard on nitrogen oxide emission, for every type of the burner facility. The burner facility for char gas burning with the pilot diffusion burner in the central part was developed and made subject to computation results. Preliminary verification nature tests on the TP-101 boiler showed that the actual content of nitrogen oxides in burner flames of char gas did not exceed a claimed concentration of 150 ppm (200 mg/m3).

The application of carbon isotope discrimination of charred wheat grains to reconstruct Late Holocene climate change and identify water management strategy in northwest China

NASA Astrophysics Data System (ADS)

Wang, W.; An, C.; Duan, F.; Zhao, Y.; Cao, Z.

2017-12-01

The AMS 14C dating and corresponding carbon stable isotope datum of charred wheat grains from archaeological sites in northwest China especially Hexi Corridor and Xinjiang have been collected widely to study its potential roles in reconstructing past climate change and identifying water management strategies through comparison with integrated regional humidity index, carbon isotope data of wheat grown under modern irrigation environment from study area and Mediterranean charred wheat carbon isotope data. The results suggest (1) carbon isotope discrimination values of charred wheat both in Hexi corridor and Xinjiang could respond well to regional moisture change, and there are also good positive correlation relationship between them (2) in contrast to consistent relationship between decreased carbon isotope discrimination values of charred wheat and dry climate condition, increased carbon isotope discrimination values does not represent wetter regional climate completely and may also reveal effects of human irrigation activities. The higher carbon isotope discrimination value of charred wheat which occurred in the Hexi Corridor from 4000 to 3850 a BP, 2100 a BP and 550 a BP and in Tianshan area of Xinjiang from 3730 a BP could be likely to be related with human activities (3) the carbon isotope discrimination value of charred wheat may have a certain limit which is generally not beyond 19‰. And this upper limit could influence its availability in reflecting abrupt change of precipitation/humidity especially rapid wetter trend. We conclude that carbon isotope analysis of charred wheat grains could be a good tool for reconstructing past climate change and identifying ancient irrigation practices.

Experimental performance of an ablative material as an external insulator for a hypersonic research aircraft

NASA Technical Reports Server (NTRS)

Puster, R. L.; Chapman, A. J.

1977-01-01

An ablative material composed of silica-filled elastomeric silicone was tested to evaluate its thermal and structural performance as an external insulator, or heat shield, for a hypersonic research aircraft. The material was also tested to determine whether it would form a durable char layer when initially heated and thereafter function primarily as an insulator with little further pyrolysis or char removal. Aerothermal tests were representative of nominal Mach 6 cruise conditions of the aircraft, and additional tests were representative of Mach 8 cruise and interference heating conditions. Radiant heating tests were used to simulate the complete nominal Mach 6 surface-temperature history. The silica char that formed during aerothermal tests was not durable. The char experienced a general and preferential surface recession, with the primary mechanism for char removal being erosion. Tests revealed that radiant heating is not a valid technique for simulating aerodynamic heating of the material.

[Dynamics of parasite fauna of different forms of salmon Salvelinus alpinus L. from the basin of the Lake Azabach'e].

PubMed

Butorina, T E

1975-01-01

The paper deals with age changes in the parasite fauna of different intraspecific forms of chars. It is shown that this year brood and yearlings of predatory, benthofagous, stream and anadromous chars up to 10 cm in length have a similar parasite fauna. During the second year of life the chars come to different feeding; correspondingly changes their parasite fauna which differs considerably in the above forms of chars. Two groups of parasites are distinguished the infection with which increases and decreases with the age of fishes. Observations were carried out on the life cycles, developmental and maturation periods of some parasites of chars. Biological peculiarities of some mixosporidia are studied. A shift in the developmental periods of helminths is noted as compared to those from the European part of the USSR.

Production and Composition of Dissolved Black Carbon from Various Biochars and Environmentally-aged Charcoals

NASA Astrophysics Data System (ADS)

Bostick, K. W.; Zimmerman, A. R.; Hatcher, P.; Mitra, S.; Wozniak, A. S.

2016-12-01

Pyrogenic organic matter, or black carbon (BC), is the solid carbonaceous product of biomass pyrolysis. While solid BC represents a long-lived portion of the C cycle, it releases pyrogenic dissolved organic matter (py-DOM) which may be more susceptible to mineralization and transformation. This py-DOM may impact environmental and public health and likely controls exchange between terrestrial and aquatic BC pools. Benzene polycarboxylic acids (BPCAs), produced by acid digestion of samples, are used as molecular markers for pyrogenic organic matter. Yet, we currently have a poor understanding of the controls on the production of py-DOM and its yield of BPCA compounds. In response, aqueous leaching time series experiments were carried out using a series of laboratory-made biochars and environmentally-aged charcoals. While non-charred oak biomass released 31.8 mg C/g (45% C loss), oak biochars prepared at low temperatures (250 and 400ºC), produced 9.9 and 2.6 mg C/g (11 and 2.3% C loss), respectively. Oak chars prepared at a higher temperatures (650ºC) leached only 1.85 mg C/g (1.5% C loss). In contrast, an environmentally-aged charcoal (30 y old cypress charcoal) leached 10.9% of its C. On average, 59% (ranging 38-80%) of oak pyrogenic DOC was converted into BPCAs, suggesting that oak py-DOM has a variably condensed aromatic proportion. However, much less BPCAs were generated by BC parent solids. In addition, trace amounts of BPCA were generated from non-pyrolyzed grass, oak wood, and compost leachates; these lend concern to the use of BPCAs as exclusive pyrogenic molecular markers. As expected, BPCA molecular distribution showed that condensation increased with pyrolysis temperature of solid biochars and their corresponding leachates. The comparison of these findings to 13C and 1H NMR spectra of charcoal parent solids and their leachates will further elucidate the chemistry and production mechanisms of py-DOM.

Pyrolysis of wastewater sludge and composted organic fines from municipal solid waste: laboratory reactor characterisation and product distribution.

PubMed

Agar, David A; Kwapinska, Marzena; Leahy, James J

2018-02-26

Sludge from municipal wastewater treatment plants and organic fines from mechanical sorting of municipal solid waste (MSW) are two common widespread waste streams that are becoming increasingly difficult to utilise. Changing perceptions of risk in food production has limited the appeal of sludge use on agricultural land, and outlets via landfilling are diminishing rapidly. These factors have led to interest in thermal conversion technologies whose aim is to recover energy and nutrients from waste while reducing health and environmental risks associated with material re-use. Pyrolysis yields three output products: solid char, liquid oils and gas. Their relative distribution depends on process parameters which can be somewhat optimised depending on the end use of product. The potential of pyrolysis for the conversion of wastewater sludge (SS) and organic fines of MSW (OF) to a combustion gas and a carbon-rich char has been investigated. Pyrolysis of SS and OF was done using a laboratory fixed-bed reactor. Herein, the physical characterisation of the reactor is described, and results on pyrolysis yields are presented. Feedstock and chars have been characterised using standard laboratory methods, and the composition of pyrolysis gases was analysed using micro gas chromatography. Product distribution (char/liquid/gas) from the pyrolysis of sewage sludge and composted MSW fines at 700°C for 10 min were 45/26/29 and 53/14/33%, respectively. The combustible fractions of pyrolysis gases range from 36 to 54% for SS feedstock and 62 to 72% from OF. The corresponding lower heating value range of sampled gases were 11.8-19.1 and 18.2-21.0 MJ m -3 , respectively.

Fire and heat resistant laminating resins based on maleimido substituted aromatic cyclotriphosphazene polymer

NASA Technical Reports Server (NTRS)

Kumar, Devendra (Inventor); Fohlen, George M. (Inventor); Parker, John A. (Inventor)

1987-01-01

4-Aminophenoxy cyclotriphosphazenes are reacted with maleic anhydride to produce maleamic acids which are converted to the maleimides. The maleimides are polymerized. By selection of starting materials (e.g., hexakis amino or trisaminophenoxy trisphenoxy cyclotriphosphazenes), selection of molar proportions of reactants, use of mixtures of anhydrides and use of dianhydrides as bridging groups a variety of maleimides and polymers are produced. The polymers have high limiting oxygen indices, high char yields and other useful heat and fire resistant properties making them useful as, for example, impregnants of fabrics.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Kwang Ho; Dutta, Tanmoy; Walter, Eric D.

Chemoselective blocking of the phenolic hydroxyl (Ar–OH) group by methylation was found to suppress secondary repolymerization and charring during lignin depolymerization. Methylation of Ar–OH prevents formation of reactive quinone methide intermediates, which are partly responsible for undesirable secondary repolymerization reactions. Instead, this structurally modified lignin produces more relatively low molecular weight products from lignin depolymerization compared to unmodified lignin. This result demonstrates that structural modification of lignin is desirable for production of low molecular weight phenolic products. Finally, this approach could be directed toward alteration of natural lignification processes to produce biomass that is more amenable to chemical depolymerization.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Kwang Ho; Dutta, Tanmoy; Walter, Eric D.

Chemoselective blocking of the phenolic hydroxyl (Ar-OH) group by methylation was found to suppress secondary repolymerization and charring during lignin depolymerization. Methylation of Ar-OH prevents formation of reactive quinone methide intermediates, which are partly responsible for undesirable secondary repolymerization reactions. Instead, this structurally modified lignin produces more relatively low molecular weight products from lignin depolymerization compared to unmodified lignin. This result demonstrates that structural modification of lignin is desirable for production of low molecular weight phenolic products. This approach could be directed toward alteration of natural lignification processes to produce biomass more amenable to chemical depolymerization.

Using bark char codes to predict post-fire cambium mortality

Treesearch

Sharon M. Hood; Danny R. Cluck; Sheri L. Smith; Kevin C. Ryan

2008-01-01

Cambium injury is an important factor in post-fire tree survival. Measurements that quantify the degree of bark charring on tree stems after fire are often used as surrogates for direct cambium injury because they are relatively easy to assign and are non-destructive. However, bark char codes based on these measurements have been inadequately tested to determine how...

Magnetic separation of carbon-encapsulated Fe nanoparticles from thermally-treated wood char

Treesearch

Sung Phil Mun; Zhiyong Cai; Jilei Zhang

2013-01-01

Wood char,a by-product from the fast-pyrolysis process of southern yellow pine wood for bio-oil production, was carbonized with Fenano particles (FeNPs) as a catalyst to prepare carbon-encapsulated Fe nanoparticles. A magnetic separation method was tested to isolate carbon-encapsulated Fe nano particles from the carbonized char. X-ray diffraction pattern clearly shows...

Graphite fiber surface treatment to improve char retention and increase fiber clumping

NASA Technical Reports Server (NTRS)

Paul, J. T., Jr.; Weldy, W. E.

1980-01-01

Composites containing carbon and graphite fibers can release fibers into the atmosphere during a fire. This release can potentially cause failure in some types of electrical equipment. Reduced fiber dispersion during and after combustion will reduce risks. Epoxidized char forming systems were synthesized which will react with commercially available surface treated carbon fiber. Fibers modified with these char formers retained adhesion in a specific epoxy matrix resin. Small scale combustion testing indicates that using these char former modified fibers in laminates will help to reduce the dispersement of fibers resulting from exposure to fire without sacrificing resin to fiber adhesion.

Synergistic effects of mica and wollastonite fillers on thermal performance of intumescent fire retardant coating

NASA Astrophysics Data System (ADS)

Zia-ul-Mustafa, M.; Ahmad, Faiz; Megat-Yusoff, Puteri S. M.; Aziz, Hammad

2015-07-01

In this study, intumescent fire retardant coatings (IFRC) were developed to investigate the synergistic effects of reinforced mica and wollastonite fillers based IFRC towards heat shielding, char expansion, char composition and char morphology. Ammonium poly-phosphate (APP) was used as acid source, expandable graphite (EG) as carbon source, melamine as blowing agent, boric acid as additive and Hardener H-2310 polyamide amine in bisphenol A epoxy resin BE-188(BPA) was used as curing agent. Bunsen burner fire test was used for thermal performance according to UL-94 for 1 h. Field Emission Scanning Electron Microscopy (FESEM) was used to observe char microstructure. X-Ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) were used to analyse char composition. The results showed that addition of clay filler in IFRC enhanced the fire protection performance of intumescent coating. X-Ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) results showed the presence of boron phosphate, silicon phosphate oxide, aluminium borate in the char that improved the thermal performance of intumescent fire retardant coating (IFRC). Resultantly, the presence of these developed compounds enhanced the Integrity of structural steel upto 500°C.

Understanding the Impact of Charcoal Inputs to Soils and Sediments on Conventional Geochemical Markers

NASA Astrophysics Data System (ADS)

Kuo, L.; Louchouarn, P.; Herbert, B.

2008-12-01

Chars/charcoals are solid combustion residues derived from biomass burning. They represent one of the major classes in the pyrogenic organic residues, the so-called black carbon (BC), and have highly heterogeneous nature due to the highly variable combustion conditions during biomass burning. More and more attention has been given to characterize and quantify the inputs of charcoals to different environmental compartments since they also share the common features of BC, such as recalcitrant nature and strong sorption capacity on hydrophobic organic pollutants. Moreover, such inputs also imply the thermal alteration of terrestrial organic matter, as well as corresponding biomarkers such as lignin. Lignin is considered to be among the best-preserved components of vascular plants after deposition, due to its relative stability on biodegradation. This macropolymer is an important contributor to soil organic matter (SOM) and its presence in aquatic environments helps trace the input of terrigenous organic matter to such systems. The yields and specific ratios of lignin oxidation products (LOP) from alkaline cupric oxide (CuO) oxidation method have been extensively used to identify the structure of plant lignin and estimate inputs of plant carbon to soils and aquatic systems, as well as evaluate the diagenetic status of lignin. Although the fate of lignin under microbiological and photochemical degradation pathways have been thoroughly addressed in the literature, studies assessing the impact of thermal degradation on lignin structure and signature are scarce. In the present study, we used three suites of lab-made chars (honey mesquite, cordgrass, and loblolly pine) to study the impact of combustion on lignin and their commonly used parameters. Our results show that combustion can greatly decrease the yields of the eight major lignin phenols (vanillyl, syringyl, and cinnamyl phenols) with no lignin phenols detected in any synthetic char produced at ≥ 400°C. With increasing combustion temperature, internal phenol ratios (S/V and C/V) show a two-stage change with an initial increase at low temperatures followed by marked and rapid decreases when temperatures reach 200- 250°C. The acid/aldehyde ratios of vanillyl phenols ((Ad/Al)v) and syringyl phenols ((Ad/Al)s) all increase with increasing combustion temperature and duration and reach a maximum values at 300- 350°C, regardless plant species. The highly elevated acid/aldehyde ratios reached in some cases exceed the reported values of humic and fulvic acids extracted from soils and sediments. We applied these empirical data in mixing models to estimate the potential effects of charcoal inputs on the observed lignin signatures in environmental mixtures. The shifts in lignin signatures are strongly influenced both by the characteristics of the charcoal incorporated and the proportion of charcoal in the mixture. We validated our observations with two sets of environmental samples, including soils from control burning sites, and a sediment core from a wetland with evidence of charcoal inputs, showing that the presences of charcoals do alter the observed lignin signals in these samples. Such a thermal "interference" on lignin parameters should thus be considered in environmental mixtures with recognized char input.

Amelioration of soil PAH and heavy metals by combined application of fly ash and biochar

NASA Astrophysics Data System (ADS)

Masto, Reginald; George, Joshy; Ansari, Md; Ram, Lal

2016-04-01

Generation of electricity through coal combustion produces huge quantities of fly ash. Sustainable disposal and utilization of these fly ash is a major challenge. Fly ash along with other amendments like biochar could be used for amelioration of soil. In this study, fly ash and biochar were used together for amelioration of polycyclic aromatic hydrocarbon (PAH) contaminated soil. Field experiment was conducted to investigate the effects of fly ash and biochar on the amelioration of soil PAH, and the yield of Zea mays. The treatments were control, biochar (4 t/ha), fly ash (4 t/ha), ash + biochar ( 2 + 2 t/ha). Soil samples were collected after the harvest of maize crop and analysed for chemical and biological parameters. Thirteen PAHs were analysed in the postharvest soil samples. Soil PAHs were extracted in a microwave oven at 120 °C using hexane : acetone (1:1) mixture. The extracted solutions were concentrated, cleaned and the 13 PAHs [Acenaphthene (Ace), fluorene (Flr), phenanthrene (Phn), anthracene(Ant), pyrene(Pyr), benz(a)anthracene (BaA), chrysene (Chy), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene, benzo(g,h,i)perylene (BghiP), dibenzo(a,h)anthracene, and indeno(1,2,3-cd)pyrene)(Inp)] were analysed using GC-MS. The mean pH increased from 6.09 in control to 6.64 and 6.58 at biochar and fly ash treated soils, respectively. N content was not affected, whereas addition of biochar alone and in combination with fly ash, has significantly increased the soil organic carbon content. P content was almost double in combined (9.06 mg/kg) treatment as compared to control (4.32 mg/kg). The increase in K due to biochar was 118%, whereas char + ash increased soil K by 64%. Soil heavy metals were decreased: Zn (-48.4%), Ni (-41.4%), Co (-36.9%), Cu (-35.7%), Mn (-34.3%), Cd (-33.2%), and Pb (-30.4%). Soil dehydrogenase activity was significantly increased by ash and biochar treatments and the maximum activity was observed for the combined treatment. Peroxidase, phenol oxidase, and catalase activities were not affected by these treatments. Acid phosphatase activity decreased, whereas alkaline phosphatase activity increased due to biochar and fly ash treatment. Microbial biomass carbon increased significantly (P < 0.05) with biochar (+27.9%), fly ash (19.8%), and char + ash (+27.9%) applications. Maize grain yield was increased by biochar (+11.4%) and char + ash (+28.1%) treatments. The total PAH concentration decreased from 4191 μg/kg in control to 1930 μg/kg in fly ash; 1509 μg/kg in biochar and 1011 μg/kg in ash + char treatments. Among the different PAHs the concentration was higher for BkF, which decreased from 713 μg/kg in control to 139 - 315 μg/kg under different treatments. Overall, combined application of fly ash and biochar was found to be effective in amelioration of soil quality parameters and improving crop yield.

Fracture in Phenolic Impregnated Carbon Ablator

NASA Technical Reports Server (NTRS)

Agrawal, Parul; Chavez-Garcia, Jose F.

2011-01-01

The thermal protection materials used for spacecraft heat shields are subjected to various thermal-mechanical loads during an atmospheric entry which can threaten the structural integrity of the system. This paper discusses the development of a novel technique to understand the failure mechanisms inside thermal protection materials. The focus of research is Phenolic Impregnated Carbon Ablator (PICA). It has successfully flown on the Stardust spacecraft and is the TPS material chosen for the Mars Science Laboratory (MSL) and Dragon spacecraft. Although PICA has good thermal properties, structurally, it is a weak material. In order to thoroughly understand failure in PICA, fracture tests were performed on FiberForm* (precursor of PICA), virgin and charred PICA materials. Several samples of these materials were tested to investigate failure mechanisms at a microstructural scale. Stress-strain data were obtained simultaneously to estimate the fracture toughness. It was found that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred PICA, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred PICA showed greater strength values compared to FiberForm coupons, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Bio-oil and biochar production from corn cobs and stover by fast pyrolysis

USDA-ARS?s Scientific Manuscript database

Bio-oil and bio-char were produced from corn cobs and corn stover (stalks, leaves and husks) by fast pyrolysis using a pilot scale fluidized bed reactor. Yields of 60% (mass/mass) bio-oil (high heating values are ~20,000 kJ/kg, and densities > 1.0 g/mL) were realized from both corn cobs and from co...

A Mechanistic Investigation of Nitrogen Evolution and Corrosion with Oxy-Combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dale Tree; Andrew Mackrory; Thomas Fletcher

A premixed, staged, down-fired, pulverized coal reactor and a flat flame burner were used to study the evolution of nitrogen in coal contrasting differences in air and oxy-combustion. In the premixed reactor, the oxidizer was staged to produce a fuel rich zone followed by a burnout zone. The initial nominal fuel rich zone stoichiometric ratio (S.R.) of 0.85 selected produced higher NO reductions in the fuel rich region under oxy-combustion conditions. Air was found to be capable of similar NO reductions when the fuel rich zone was at a much lower S.R. of 0.65. At a S.R. of 0.85, oxy-combustionmore » was measured to have higher CO, unburned hydrocarbons, HCN and NH{sub 3} in the fuel rich region than air at the same S.R. There was no measured difference in the initial formation of NO. The data suggest devolatilization and initial NO formation is similar for the two oxidizers when flame temperatures are the same, but the higher CO{sub 2} leads to higher concentrations of CO and nitrogen reducing intermediates at a given equivalence ratio which increases the ability of the gas phase to reduce NO. These results are supported by flat flame burner experiments which show devolatilization of nitrogen from the coal and char to be similar for air and oxy-flame conditions at a given temperature. A model of premixed combustion containing devolatilization, char oxidation and detailed kinetics captures most of the trends seen in the data. The model suggests CO is high in oxy-combustion because of dissociation of CO{sub 2}. The model also predicts a fraction (up to 20%, dependent on S.R.) of NO in air combustion can be formed via thermal processes with the source being nitrogen from the air while in oxy-combustion equilibrium drives a reduction in NO of similar magnitude. The data confirm oxy-combustion is a superior oxidizer to air for NO control because NO reduction can be achieved at higher S.R. producing better char burnout in addition to NO from recirculated flue gas being reduced as it passes back through the flame.« less

Pyrolysis conditions and ozone oxidation effects on ammonia adsorption in biomass generated chars.

PubMed

Kastner, James R; Miller, Joby; Das, K C

2009-05-30

Ammonia adsorbents were generated via pyrolysis of biomass (peanut hulls and palm oil shells) over a range of temperatures and compared to a commercially available activated carbon (AC) and solid biomass residuals (wood and poultry litter fly ash). Dynamic ammonia adsorption studies (i.e., breakthrough curves) were performed using these adsorbents at 23 degrees C from 6 to 17 ppmv NH(3). Of the biomass chars, palm oil char generated at 500 degrees C had the highest NH(3) adsorption capacity (0.70 mg/g, 6 ppmv, 10% relative humidity (RH)), was similar to the AC, and contrasted to the other adsorbents (including the AC), the NH(3) adsorption capacity significantly increased if the relative humidity was increased (4 mg/g, 7 ppmv, 73% RH). Room temperature ozone treatment of the chars and activated carbon significantly increased the NH(3) adsorption capacity (10% RH); resultant adsorption capacity, q (mg/g) increased by approximately 2, 6, and 10 times for palm oil char, peanut hull char (pyrolysis only), and activated carbon, respectively. However, water vapor (73% RH at 23 degrees C) significantly reduced NH(3) adsorption capacity in the steam and ozone treated biomass, yet had no effect on the palm shell char generated at 500 degrees C. These results indicate the feasibility of using a low temperature (and thus low energy input) pyrolysis and activation process for the generation of NH(3) adsorbents from biomass residuals.

Examination of Scanning Electron Microscope and Computed Tomography Images of PICA

NASA Technical Reports Server (NTRS)

Lawson, John W.; Stackpoole, Margaret M.; Shklover, Valery

2010-01-01

Micrographs of PICA (Phenolic Impregnated Carbon Ablator) taken using a Scanning Electron Microscope (SEM) and 3D images taken with a Computed Tomography (CT) system are examined. PICA is a carbon fiber based composite (Fiberform ) with a phenolic polymer matrix. The micrographs are taken at different surface depths and at different magnifications in a sample after arc jet testing and show different levels of oxidative removal of the charred matrix (Figs 1 though 13). CT scans, courtesy of Xradia, Inc. of Concord CA, were captured for samples of virgin PICA, charred PICA and raw Fiberform (Fig. 14). We use these images to calculate the thermal conductivity (TC) of these materials using correlation function (CF) methods. CF methods give a mathematical description of how one material is embedded in another and is thus ideally suited for modeling composites like PICA. We will evaluate how the TC of the materials changes as a function of surface depth. This work is in collaboration with ETH-Zurich, which has expertise in high temperature materials and TC modeling (including CF methods).

Modeling the pyrolysis study of non-charring polymers under reduced pressure environments

NASA Astrophysics Data System (ADS)

Zong, Ruowen; Kang, Ruxue; Hu, Yanghui; Zhi, Youran

2018-04-01

In order to study the pyrolysis of non-charring polymers under reduced pressure environments, a series of experiments based on black acrylonitrile butadiene styrene (ABS) was conducted in a reduced pressure chamber under different external heat fluxes. The temperatures of the top surface and the bottom of the sample and the mass loss during the whole process were measured in real time. A one-dimensional numerical model was developed to predict the top surface and the bottom surface temperatures of ABS during the pyrolysis at different reduced pressures and external heat fluxes, and the model was validated by the experimental data. The results of the study indicate that the profiles of the top surface and the bottom surface temperatures are different at different pressures and heat fluxes. The temperature and the mass loss rate of the sample under a lower heat flux decreased significantly as the pressure was increased. However, under a higher heat flux, the temperature and the mass loss rate showed little sensitivity to the pressure. The simulated results fitted the experimental results better at the higher heat flux than at the lower heat flux.

Influences of metal ions crosslinked alginate based coatings on thermal stability and fire resistance of cotton fabrics.

PubMed

Pan, Ying; Wang, Wei; Liu, Longxiang; Ge, Hua; Song, Lei; Hu, Yuan

2017-08-15

Bio-based and phosphorus-free coating was fabricated by layer-by-layer assembly method to obtain the flame retardant cotton fabric. For the first time, the modified cotton fabrics were prepared by utilizing positively charged polyethylenimine and negatively charged alginate together with subsequent crosslinking of barium, nickel and cobalt ions. Scanning electron microscopy and energy-dispersive X-ray demonstrated that the metal ions crosslinked coating was successfully constructed on the substrate. The thermal stability and flame retardancy were investigated by thermogravimetric analysis (TGA) and horizontal flame tests. TGA results showed that the degradation of the coated cotton fabrics were retarded at high temperature and the char residue of the cotton fabrics were improved after covered with the barium, nickel and cobalt ions crosslinked coatings. Furthermore, the fire resistance of cotton-Ba sample was enhanced significantly compared with the untreated sample, as evidenced by the obvious reduction (28%) of flame spread rate and complete char residue. Finally, the washing durability of coating on the fabric was enhanced after metal ions crosslinked with alginate based coating. Copyright © 2017. Published by Elsevier Ltd.

Microgravity Smoldering Combustion on the USML-1 Space Shuttle Mission

NASA Technical Reports Server (NTRS)

Stocker, Dennis P.; Olson, Sandra L.; Torero, Jose L.; Fernandez-Pello, A Carlos

1994-01-01

Preliminary results from an experimental study of the smolder characteristics of a porous combustible material (flexible polyurethane foam) in normal and microgravity are presented. The experiments, limited in fuel sample size and power available for ignition, show that the smolder process was primarily controlled by heat losses from the reaction to the surrounding environment. In microgravity, the reduced heat losses due to the absence of natural convection result in only slightly higher temperatures in the quiescent microgravity test than in normal gravity but a dramatically larger production of combustion products in all microgravity tests. Particularly significant is the proportionately larger amount of carbon monoxide and light organic compounds produced in microgravity, despite comparable temperatures and similar char patterns. This excessive production of fuel-rich combustion products may be a generic characteristic of smoldering polyurethane in microgravity, with an associated increase in the toxic hazard of smolder in spacecraft.

Microgravity smoldering combustion on the USML-1 Space Shuttle mission

NASA Technical Reports Server (NTRS)

Stocker, Dennis P.; Olson, Sandra L.; Torero, Jose L.; Fernandez-Pello, A. Carlos

1995-01-01

Preliminary results from an experimental study of the smolder characteristics of a porous combustible material (flexible polyurethane foam) in normal and microgravity are presented. The experiments, limited in fuel sample size and power available for ignition, show that the smolder process was primarily controlled by heat losses from the reaction to the surrounding environment In microgravity, the reduced heat losses due to the absence of natural convection result in only slightly higher temperatures in the quiescent microgravity test than in normal gravity, but a dramatically larger production of combustion products in all microgravity tests. Particularly significant is the proportionately larger amount of carbon monoxide and light organic compounds produced in microgravity, despite comparable temperatures and similar char patterns. This excessive production of fuel-rich combustion products may be a generic characteristic of smoldering polyurethane in microgravity, with an associated increase in the toxic hazard of smolder in spacecraft.

Charring rate of wood exposed to a constant heat flux

Treesearch

R. H. White; H. C. Tran

1996-01-01

A critical factor in the fire endurance of a wood member is its rate of charring. Most available charring rate data have been obtained using the time-temperature curves of the standard fire resistance tests (ASTM E 119 and ISO 834) to define the fire exposure. The increased use of heat release calorimeters using exposures of constant heat flux levels has broadened the...

Improved regeneration and transformation protocols for three strawberry cultivars

PubMed Central

Zakaria, Hossam; Hussein, Gihan M; Abdel-Hadi, Abdel-Hadi A; Abdallah, Naglaa A

2014-01-01

Strawberry (Fragaria × ananassa) is an economically important soft fruit crop with polyploid genome which makes the breeding of new cultivars difficult. Simple and efficient method for transformation and regeneration is required for cultivars improvement in strawberry. In the present study, adventitious shoot regeneration has been investigated in three cultivated strawberry plants, i.e., Festival, Sweet Charly and Florida via direct organogenesis using the in vitro juvenile leaves as explants. Explants were collected after sub-culturing on a propagation medium composed of MS supplemented with 0.5 mg/l BA; 0.1 mg/l GA3 and 0.1 mg/l IBA. To select the suitable organogenesis, the explants of the three cultivars were cultured on MS medium supplemented with different concentrations of TDZ (1, 2, 3, and 4 mg/l), then incubated at a temperature of 22 °C ± 2. Medium containing 2 mg/l TDZ revealed the best regeneration efficiency with the three cultivars (72% for Festival, and 73% for Sweet Charly and Florida). After 4 weeks, the produced shoots were cultured on MS medium with different concentrations of BA and Kin to enhance shoot elongation. Results showed that the medium containing 1.5 mg/l BA and 0.5 mg/l Kin revealed highest elongation efficiency (88% and 94%) for Festival and Sweet Charly, respectively. On the other hand, medium containing 1.5 mg/l BA and 0.1 mg/l Kin showed highest elongation efficiency (90%) in Florida. Elongated shoots were successfully rooted on MS medium containing 1.5 mg/l NAA. Furthermore, transformation of the two cultivars, Festival and Sweet Charly, has been established via Agrobacterium strain LBA44404 containing the plasmid pISV2678 with gus-intron and bar genes. Three days post co-cultivation, GUS activity was screening using the histochemical assay. The results showed 16% and 18% of the tested plant materials has changed into blue color for Festival and Sweet Charly, respectively. Out of 120 explants only 13 shoots were developed on bialaphos medium for each cultivar, representing 10.8% bialaphos resistant strawberry shoot. The presence of the both genes bar and uid A was detected by PCR and Northern giving a transformation efficiency of 5%. PMID:24322545

Development and Verification of Enclosure Radiation Capabilities in the CHarring Ablator Response (CHAR) Code

NASA Technical Reports Server (NTRS)

Salazar, Giovanni; Droba, Justin C.; Oliver, Brandon; Amar, Adam J.

2016-01-01

With the recent development of multi-dimensional thermal protection system (TPS) material response codes, the capability to account for surface-to-surface radiation exchange in complex geometries is critical. This paper presents recent efforts to implement such capabilities in the CHarring Ablator Response (CHAR) code developed at NASA's Johnson Space Center. This work also describes the different numerical methods implemented in the code to compute geometric view factors for radiation problems involving multiple surfaces. Verification of the code's radiation capabilities and results of a code-to-code comparison are presented. Finally, a demonstration case of a two-dimensional ablating cavity with enclosure radiation accounting for a changing geometry is shown.

Charring Rate for Fire Exposed X-Lam

NASA Astrophysics Data System (ADS)

Wong, Bernice VY; Fah Tee, Kong

2017-06-01

Design of timber structures has been outlined in Eurocode 5. Notional charring rate for softwood and hardwood timber is given. For the performance of X-LAM panels in fire, only little information on charring is available and whether the fire behaviour of X-LAM is similar to homogenous timber panels has not yet been systematically analysed. This paper presents an overview of fire performance of X-LAM and evaluation of its resistance to elevated temperature as an element of structure in comparison to homogeneous timber panels. Numerical study has been carried out based on available experimental results. Charring rates for X-LAM panels obtained from experimental results are compared with those obtained from Eurocode 5 and proposed simplified model.

The thermal and mechanical properties of a low-density glass-fiber-reinforced elastomeric ablation material

NASA Technical Reports Server (NTRS)

Engelke, W. T.; Robertson, R. W.; Bush, A. L.; Pears, C. D.

1974-01-01

An evaluation of the thermal and mechanical properties was performed on a molded low-density elastomeric ablation material designated as Material B. Both the virgin and charred states were examined to provide meaningful inputs to the design of a thermal protection system. Chars representative of the flight chars formed during ablation were prepared in a laboratory furnace from 600 K to 1700 K and properties of effective thermal conductivity, heat capacity, porosity and permeability were determined on the furnace chars formed at various temperature levels within the range. This provided a boxing of the data which will enable the prediction of the transient response of the material during flight ablation.

Erosion characteristics of ethylene propylene diene monomer composite insulation by high-temperature dense particles

NASA Astrophysics Data System (ADS)

Li, Jiang; Guo, Meng-fei; Lv, Xiang; Liu, Yang; Xi, Kun; Guan, Yi-wen

2018-04-01

In this study, a dense particles erosion test motor which can simulate the erosion state of a solid rocket motor under high acceleration was developed. Subsequently, erosion experiments were carried out for the ethylene propylene diene monomer composite insulation and the microstructure of the char layer analysed. A turning point effect was found from the influence of the particle impact velocity on the ablation rate, and three erosion modes were determined according to the micro-morphology of the char layer. A reasonable explanation for the different structures of the char layer in the three modes was presented based on the formation mechanism of the compact/loose structure of the char layer.

Feasibility Assessment of Thermal Barrier Seals for Extreme Transient Temperatures

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M.; Dunlap, Patrick H., Jr.

1998-01-01

The assembly joints of modem solid rocket motor cases are generally sealed using conventional O-ring type seals. The 5500+ F combustion gases produced by rocket motors are kept a safe distance away from the seals by thick layers of phenolic insulation. Special compounds are used to fill insulation gaps leading up to the seals to prevent a direct flowpath to them. Design criteria require that the seals should not experience torching or charring during operation, or their sealing ability would be compromised. On limited occasions, NASA has observed charring of the primary O-rings of the Space Shuttle solid rocket nozzle assembly joints due to parasitic leakage paths opening up in the gap-fill compounds during rocket operation. NASA is investigating different approaches for preventing torching or charring of the primary O-rings. One approach is to implement a braided rope seal upstream of the primary O-ring to serve as a thermal barrier that prevents the hot gases from impinging on the O-ring seals. This paper presents flow, resiliency, and thermal resistance for several types of NASA rope seals braided out of carbon fibers. Burn tests were performed to determine the time to burn through each of the seals when exposed to the flame of an oxyacetylene torch (5500 F), representative of the 5500 F solid rocket motor combustion temperatures. Rope seals braided out of carbon fibers endured the flame for over six minutes, three times longer than solid rocket motor burn time. Room and high temperature flow tests are presented for the carbon seals for different amounts of linear compression. Room temperature compression tests were performed to assess seal resiliency and unit preloads as a function of compression. The thermal barrier seal was tested in a subscale "char" motor test in which the seal sealed an intentional defect in the gap insulation. Temperature measurements indicated that the seal blocked 2500 F combustion gases on the upstream side with very little temperature rise on the downstream side.

Modeling collision energy transfer in APCI/CID mass spectra of PAHs using thermal-like post-collision internal energy distributions.

PubMed

Solano, Eduardo A; Mohamed, Sabria; Mayer, Paul M

2016-10-28

The internal energy transferred when projectile molecular ions of naphthalene collide with argon gas atoms was extracted from the APCI-CID (atmospheric-pressure chemical ionization collision-induced dissociation) mass spectra acquired as a function of collision energy. Ion abundances were calculated by microcanonical integration of the differential rate equations using the Rice-Ramsperger-Kassel-Marcus rate constants derived from a UB3LYP/6-311G+(3df,2p)//UB3LYP/6-31G(d) fragmentation mechanism and thermal-like vibrational energy distributions p M E,T char . The mean vibrational energy excess of the ions was characterized by the parameter T char ("characteristic temperature"), determined by fitting the theoretical ion abundances to the experimental breakdown graph (a plot of relative abundances of the ions as a function of kinetic energy) of activated naphthalene ions. According to these results, the APCI ion source produces species below T char = 1457 K, corresponding to 3.26 eV above the vibrational ground state. Subsequent collisions heat the ions up further, giving rise to a sigmoid curve of T char as a function of E com (center-of-mass-frame kinetic energy). The differential internal energy absorption per kinetic energy unit (dE vib /dE com ) changes with E com according to a symmetric bell-shaped function with a maximum at 6.38 ± 0.32 eV (corresponding to 6.51 ± 0.27 eV of vibrational energy excess), and a half-height full width of 6.30 ± 1.15 eV. This function imposes restrictions on the amount of energy that can be transferred by collisions, such that a maximum is reached as kinetic energy is increased. This behavior suggests that the collisional energy transfer exhibits a pronounced increase around some specific value of energy. Finally, the model is tested against the CID mass spectra of anthracene and pyrene ions and the corresponding results are discussed.

Test evaluation of potential heatshield contamination of an outer planet probe's gas sampling system

NASA Technical Reports Server (NTRS)

Kessler, W. C.

1975-01-01

The feasibility of retaining the heat shield for outer planet probes was investigated as a potential source of atmospheric sample contamination by outgassing. The onboard instruments which are affected by the concept are the pressure sensor, temperature sensor, IR detector, nephelometer, and gas sampling instruments. It was found that: (1) The retention of the charred heatshield and the baseline atmospheric sampling concepts are compatible with obtaining noncontaminated atmospheric samples. (2) Increasing the sampling tube length so that it extends beyond the viscous boundary layer eliminates contamination of the atmospheric sample. (3) The potential for contamination increases with angle of attack.

Novel sorbent materials for environmental remediation via Pyrolysis of biomass

NASA Astrophysics Data System (ADS)

Zabaniotou, Anastasia

2013-04-01

One of the major challenges facing society at this moment is the transition from a non-sustainable, fossil resources-based economy to a sustainable bio-based economy. By producing multiple products, a biorefinery can take advantage of the differences in biomass components and intermediates and maximize the value derived from the biomass feedstock. The high-value products enhance profitability, the high-volume fuel helps meet national energy needs, and the power production reduces costs and avoids greenhouse-gas emissions From pyrolysis, besides gas and liquid products a solid product - char, is derived as well. This char contains the non converted carbon and can be used for activated carbon production and/or as additive in composite material production. Commercially available activated carbons are still considered expensive due to the use of non-renewable and relatively expensive starting material such as coal. The present study describes pyrolysis as a method to produce high added value carbon materials such as activated carbons (AC) from agricultural residues pyrolysis. Olive kernel has been investigated as the precursor of the above materials. The produced activated carbon was characterized by proximate and ultimate analyses, BET method and porosity estimation. Furthermore, its adsorption of pesticide compound in aqueous solution by was studied. Pyrolysis of olive kernel was conducted at 800 oC for 45min in a fixed reactor. For the production of the activated carbon the pyrolytic char was physically activated under steam in the presence of CO2 at 970oC for 3 h in a bench scale reactor. The active carbons obtained from both scales were characterized by N2 adsorption at 77 K, methyl-blue adsorption (MB adsorption) at room temperature and SEM analysis. Surface area and MB adsorption were found to increase with the degree of burn-off. The surface area of the activated carbons was found to increase up to 1500 m2/g at a burn-off level of 60-65wt.%, while SEM analysis showed the appearance of micropores to mesopores in the produced tire active carbons. Activated carbon prepared from olive kernel is a super active carbon and used as an adsorbent for the removal of pesticide from aqueous solutions (Bromopropylate). The higher removal achieved was 100% in 60 min. The produced activated carbon from agricultural residue was proved to be very effective for gas and water stream purification. Biomass can give a wide spectrum of fuels and materials in the integrated concept of biorefinery

Dwarf char, a new form of chars (the genus Salvelinus) in Lake Kronotskoe

USGS Publications Warehouse

Pavlov, S.D.; Pivovarov, E.A.; Ostberg, C.O.

2012-01-01

Lake Kronotskoe is situated in the Kronotskii State Nature Reserve and is a unique natural heritage of Kamchatka. The lake–river system of the reserve includes numerous springs and small streams and three large inflowing rivers, Listvennichnaya, Unana, and Uzon, which form the main bays of Lake Kronotskoe; one river (Kronotskaya) flows from the lake. This river is characterized by several rapids, which are assumed to be unsurmountable barriers for fish migration. The ichthyofauna of the lake has been isolated for a long time, and some endemic fishes appeared, including char of the genus Salvelinus and the residential form of red salmon Oncorhynchus nerka (the local name is kokanee). These species are perfect model objects to study microevolution processes. Char of Lake Kronotskoe are characterized by significant polymorphism and plasticity [1–3]; therefore, they are extremely valuable for studying the processes of speciation and form development. That is why the populations of char in Lake Kronotskoe are unique and attract special attention of researchers. 

Short-term effects of triiodothyronine on the bowfin, Amia calva (Holostei), and the lake char, Salvelinus namaycush (Teleostei).

PubMed

Ballantyne, J S; John, T M; Singer, T D; Oommen, O V

1992-01-01

To assess the role of triiodothyronine (T3) in mediating short-term changes in metabolism, such as those occurring in circadian patterns, we examined the effects of intraperitoneal injection of T3 on the oxidation of substrates by isolated mitochondria from liver of the bowfin, Amia calva, and red muscle and liver of the lake char, Salvelinus namaycush. Selected enzymes were measured in red muscle and liver of the lake char. Three hours after intraperitoneal injection of T3, oxidation of some substrates by mitochondria isolated from the liver of the bowfin was reduced. Similar treatment had no effect on substrate oxidation in liver mitochondria isolated from lake char. Oxidation of substrates by lake char red muscle mitochondria was stimulated by T3 injection. Citrate synthase levels were increased in red muscle suggesting that changes in enzyme activity may be in part responsible for the short-term mitochondrial responses to T3 injection.

CO2 gasification of char from lignocellulosic garden waste: Experimental and kinetic study.

PubMed

Gupta, Ankita; Thengane, Sonal K; Mahajani, Sanjay

2018-04-25

In this study, the dry leaves litter from jackfruit, raintree, mango and eucalyptus trees, lignin, and cellulose were characterized, pyrolysed, and evaluated for their char reactivity towards CO 2 gasification using TGA. The differences in char reactivity were attributed to the difference in char morphology and the varying inorganic contents. The mineral analysis of biomass ash showed the presence of alkali minerals some of which could act as catalysts. The adverse effect of high silica content was also evident through the experimental results. The kinetic parameters for gasification reaction were determined using three different reaction models. A modified random pore model was investigated to account for the influence of inorganic content. The effect of external catalyst on CO 2 gasification was also studied by adding potassium carbonate to biomass char and pellets. The results obtained from this study can be conveniently used in the design of a gasifier for lignocellulosic garden waste. Copyright © 2018 Elsevier Ltd. All rights reserved.

Behaviors of Char Gasification Based on Two-stage Gasifier of Biomass

NASA Astrophysics Data System (ADS)

Taniguchi, Miki; Sasauchi, Kenichi; Ahn, Chulju; Ito, Yusuke; Hayashi, Toshiaki; Akamatsu, Fumiteru

In order to develop a small-scale gasifier in which biomass can be converted to energy with high efficiency, we planed a gasification process that consists of two parts: pyrolysis part (rotary kiln) and gasification part (downdraft gasifier). We performed fundamental experiments on gasification part and discussed the apropriate conditions such as air supply location, air ratio, air temperature and hearth load. The following results was found: 1) the air supply into the char bed is more effective than that into the gas phase, 2) we can have the maximum cold gas efficiency of 80% on the following conditions: air supply location: char layer, air temperature: 20°C, air ratio: 0.2. 3) As air temperature is higher, the cold gas efficiency is larger. As for the hearth load, the cold gas efficiency becomes higher and reaches the constant level. It is expected from the results that high temperature in the char layer is effective on the char gasification.

Basic study of charring detection at the laser catheter-tip using back scattering light measurement during therapeutic laser irradiation in blood.

PubMed

Takahashi, Mei; Ito, Arisa; Kajihara, Takuro; Matsuo, Hiroki; Arai, Tsunenori

2010-01-01

The purpose of this study is to investigate transient process of the charring at the laser catheter-tip in blood during therapeutic laser irradiation by the back scattering light measurement to detect precursor state of the charring. We took account of using photodynamic therapy for arrhythmia in blood through the laser catheter. We observed the influence of the red laser irradiation (λ=663 nm) upon the shape of red blood cells (RBCs). The RBCs aggregation, round formation, and hemolysis were took place sequentially before charring. With a model blood sandwiched between glass plates simulated as a catheter-tip boundary, we measured diffuse-reflected-light power and transmitted-light power simultaneously and continuously by a microscopic optics during the laser irradiation. We found that measured light power changes were originated with RBCs shape change induced by temperature rise due to the laser irradiation. A gentle peak following a slow descending was observed in the diffuse-reflected-light power history. This history might indicate the precursor state of the charring, in which the hemolysis might be considered to advance rapidly. We think that the measurement of diffuse-reflected-light power history might be able to detect precursor state of charring at the catheter-tip in blood.

Suprasubduction volcanic rocks of the Char ophiolite belt, East Kazakhstan: new geochemical and first geochronological data

NASA Astrophysics Data System (ADS)

Safonova, Inna; Simonov, Vladimir; Seltmann, Reimar; Yamamoto, Shinji; Xiao, Wenjiao

2016-04-01

The Char ophiolite belt is located in the western Central Asian Orogenic Belt, a world largest accretionary orogen, which has evolved during more than 800 Ma. The Char belt formed during Kazakhstan - Siberia collision. It has been known for hosting fragments of Late Devonian-Early Carboniferous oceanic crust, MORB, OPB and OIB, of the Paleo-Asian Ocean (Safonova et al., 2012). The Char is surrounded by two Paleozoic island-arc terranes: Zharma-Saur in the west and Rudny Altai in the east, however, until recent times, no island-arc units have been found within it. We were the first to find island-arc units as tectonic sheets occurring adjacent to those consisting of oceanic rocks. In places, island-arc andesites cut oceanic basalts. The Char volcanic and subvolcanic rocks of a probable suprasubduction origin are basalt, microgabbro, dolerite, andesite, tonalite and dacite. The mafic to andesitic volcanics possessing low TiO2 (0.85 wt.%av.) and show MgO vs. major elements crystallization trends suggesting two magma series: tholeiitic and calc-alkaline. The tholeiitic varieties are less enriched in incompatible elements then the calc-alkaline ones. Two samples are high-Mg and low-Ti andesibasalts similar to boninites. The rocks possess moderately LREE enriched rare-earth element patterns and are characterized by negative Nb anomalies present on the multi-element spectra (Nb/Lapm = 0.14-0.47; Nb/Thpm = 0.7-1.6).The distribution of rare-earth elements (La/Smn = 0.8-2.3, Gd/Ybn = 0.7-1.9) and the results of geochemical modeling in the Nb-Yb system suggest high degrees of melting of a depleted harzburgite-bearing mantle source at spinel facies depths. Fractional crystallization of clinopyroxene, plagioclase and opaque minerals also affected the final composition of the volcanic rocks. Clinopyroxene monomineral thermometry indicates crystallization of melts at 1020-1180°C. Melt inclusion composition based numerical calculations show that primary melts were derived at 1350-1530°C and 14-26 kbar and crystallized at 1150-1190°C (Simonov et al., 2010). All these features are indicative of a supra-subduction origin of rocks. The age of gabbro, dolerite, andesite and tonalite was determined by LA ICP MS U-Pb zircon dating performed in the University of Kyoto, Japan. The andesites and tonalites yielded Carboniferous ages of ca. 322-336 Ma and the gabbro and dolerite appeared Devonian (387-395 Ma). Thus, the Char volcanic rocks possess geochemical signatures of supra-subduction magmas and could be derived at high degree melting of relatively shallow mantle sources. The volcanic units probably formed at one or two island-arcs or at an intra-oceanic arc and continental margin arc during the Middle Devonian - Mississippian. Later, the island-arc units were probably accreted to the active margin of the Kazakhstan continent. The work was supported by RFBR Project no. 16-05-00313. Contribution to IGCP#592 of UNESCO-IUGS. Safonova, I.Yu., Simonov V.A., Kurganskaya E.V., Obut O.T., Romer R.L., Seltmann R., 2012. Late Paleozoic oceanic basalts hosted by the Char suture-shear zone, East Kazakhstan: geological position, geochemistry, petrogenesis and tectonic setting. Journal of Asian Earth Sciences 49, 20-39. Simonov V.A., Safonova I.Yu., Kovyazin S.V., 2010. Petrogenesis of island-arc complexes of the Char zone, East Kazakhstan. Petrology 18, 59-72.

The effect of model fidelity on prediction of char burnout for single-particle coal combustion

DOE PAGES

McConnell, Josh; Sutherland, James C.

2016-07-09

In this study, practical simulation of industrial-scale coal combustion relies on the ability to accurately capture the dynamics of coal subprocesses while also ensuring the computational cost remains reasonable. The majority of the residence time occurs post-devolatilization, so it is of great importance that a balance between the computational efficiency and accuracy of char combustion models is carefully considered. In this work, we consider the importance of model fidelity during char combustion by comparing combinations of simple and complex gas and particle-phase chemistry models. Detailed kinetics based on the GRI 3.0 mechanism and infinitely-fast chemistry are considered in the gas-phase.more » The Char Conversion Kinetics model and nth-Order Langmuir–Hinshelwood model are considered for char consumption. For devolatilization, the Chemical Percolation and Devolatilization and Kobayashi-Sarofim models are employed. The relative importance of gasification versus oxidation reactions in air and oxyfuel environments is also examined for various coal types. Results are compared to previously published experimental data collected under laminar, single-particle conditions. Calculated particle temperature histories are strongly dependent on the choice of gas phase and char chemistry models, but only weakly dependent on the chosen devolatilization model. Particle mass calculations were found to be very sensitive to the choice of devolatilization model, but only somewhat sensitive to the choice of gas chemistry and char chemistry models. High-fidelity models for devolatilization generally resulted in particle temperature and mass calculations that were closer to experimentally observed values.« less

The effect of model fidelity on prediction of char burnout for single-particle coal combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

McConnell, Josh; Sutherland, James C.

In this study, practical simulation of industrial-scale coal combustion relies on the ability to accurately capture the dynamics of coal subprocesses while also ensuring the computational cost remains reasonable. The majority of the residence time occurs post-devolatilization, so it is of great importance that a balance between the computational efficiency and accuracy of char combustion models is carefully considered. In this work, we consider the importance of model fidelity during char combustion by comparing combinations of simple and complex gas and particle-phase chemistry models. Detailed kinetics based on the GRI 3.0 mechanism and infinitely-fast chemistry are considered in the gas-phase.more » The Char Conversion Kinetics model and nth-Order Langmuir–Hinshelwood model are considered for char consumption. For devolatilization, the Chemical Percolation and Devolatilization and Kobayashi-Sarofim models are employed. The relative importance of gasification versus oxidation reactions in air and oxyfuel environments is also examined for various coal types. Results are compared to previously published experimental data collected under laminar, single-particle conditions. Calculated particle temperature histories are strongly dependent on the choice of gas phase and char chemistry models, but only weakly dependent on the chosen devolatilization model. Particle mass calculations were found to be very sensitive to the choice of devolatilization model, but only somewhat sensitive to the choice of gas chemistry and char chemistry models. High-fidelity models for devolatilization generally resulted in particle temperature and mass calculations that were closer to experimentally observed values.« less

Cow bones char as a green sorbent for fluorides removal from aqueous solutions: batch and fixed-bed studies.

PubMed

Nigri, Elbert M; Cechinel, Maria Alice P; Mayer, Diego A; Mazur, Luciana P; Loureiro, José M; Rocha, Sônia D F; Vilar, Vítor J P

2017-01-01

Cow bone char was investigated as sorbent for the defluoridation of aqueous solutions. The cow bone char was characterized in terms of its morphology, chemical composition, and functional groups present on the bone char surface using different analytical techniques: SEM, EDS, N 2 -BET method, and FTIR. Batch equilibrium studies were performed for the bone chars prepared using different procedures. The highest sorption capacities for fluoride were obtained for the acid washed (q = 6.2 ± 0.5 mg/g) and Al-doped (q = 6.4 ± 0.3 mg/g) bone chars. Langmuir and Freundlich models fitted well the equilibrium sorption data. Fluoride removal rate in batch system is fast in the first 5 h, decreasing after this time until achieving equilibrium due to pore diffusion. The presence of carbonate and bicarbonate ions in the aqueous solution contributes to a decrease of the fluoride sorption capacity of the bone char by 79 and 31 %, respectively. Regeneration of the F-loaded bone char using 0.5 M NaOH solution leads to a sorption capacity for fluoride of 3.1 mg/g in the second loading cycle. Fluoride breakthrough curve obtained in a fixed-bed column presents an asymmetrical S-shaped form, with a slow approach of C/C 0  → 1.0 due to pore diffusion phenomena. Considering the guideline value for drinking water of 1.5 mg F - /L, as recommended by World Health Organization, the service cycle for fluoride removal was of 71.0 h ([F - ] feed  ∼ 9 mg/L; flow rate = 1 mL/min; m sorbent  = 12.6 g). A mass transfer model considering the pore diffusion was able to satisfactorily describe the experimental data obtained in batch and continuous systems.

Micro-CT features of intermediate gunshot wounds severely damaged by fire.

PubMed

Fais, Paolo; Giraudo, Chiara; Boscolo-Berto, Rafael; Amagliani, Alessandro; Miotto, Diego; Feltrin, Giampietro; Viel, Guido; Ferrara, S Davide; Cecchetto, Giovanni

2013-03-01

Incineration or extensive burning of the body, causing changes in the content and distribution of fluids, fixation and shrinking processes of tissues, can alter the typical macroscopic and microscopic characteristics of firearm wounds, hampering or at least complicating the reconstruction of gunshot fatalities. The present study aims at evaluating the potential role of micro-computed tomography (micro-CT) for detecting and quantifying gunshot residue (GSR) particles in experimentally produced intermediate-range gunshot wounds severely damaged by fire. Eighteen experimental shootings were performed on 18 sections of human calves surgically amputated for medical reasons at three different firing distances (5, 15 and 30 cm). Six stab wounds produced with an ice pick were used as controls. Each calf section underwent a charring cycle, being placed in a wood-burning stove for 4 min at a temperature of 400 °C. At visual inspection, the charred entrance wounds could not be differentiated from the exit lesions and the stab wounds. On the contrary, micro-CT analysis showed the presence of GSR particles in all burnt entrance gunshot wounds, while GSR was absent in the exit and stab wounds. The GSR deposits of the firearm lesions inflicted at very close distance (5 cm) were mainly constituted of huge particles (diameter >150 μm) with an irregular shape and well-delineated edges; at greater distances (15 and 30 cm), agglomerates of tiny radiopaque particles scattered in the epidermis and dermis layers were evident. Statistical analysis demonstrated that also in charred firearm wounds the amount of GSR roughly correlates with the distance from which the gun was fired. The obtained results suggest that micro-CT analysis can be a valid screening tool for identifying entrance gunshot wounds and for differentiating firearm wounds from sharp-force injuries in bodies severely damaged by fire.

Pyrolysis of automotive shredder residue in a bench scale rotary kiln.

PubMed

Notarnicola, Michele; Cornacchia, Giacinto; De Gisi, Sabino; Di Canio, Francesco; Freda, Cesare; Garzone, Pietro; Martino, Maria; Valerio, Vito; Villone, Antonio

2017-07-01

Automotive shredder residue (ASR) can create difficulties when managing, with its production increasing. It is made of different type of plastics, foams, elastomers, wood, glasses and textiles. For this reason, it is complicated to dispose of in a cost effective way, while also respecting the stringent environmental restrictions. Among thermal treatments, pyrolysis seems to offer an environmentally attractive method for the treatment of ASR; it also allows for the recovery of valuable secondary materials/fuels such as pyrolysis oils, chars, and gas. While, there is a great deal of significant research on ASR pyrolysis, the literature on higher scale pyrolysis experiments is limited. To improve current literature, the aim of the study was to investigate the pyrolysis of ASR in a bench scale rotary kiln. The Italian ASR was separated by dry-sieving into two particle size fractions: d<30mm and d>30mm. Both the streams were grounded, pelletized and then pyrolyzed in a continuous bench scale rotary kiln at 450, 550 and 650°C. The mass flow rate of the ASR pellets was 200-350g/h and each test ran for about 4-5h. The produced char, pyrolysis oil and syngas were quantified to determine product distribution. They were thoroughly analyzed with regard to their chemical and physical properties. The results show how higher temperatures increase the pyrolysis gas yield (44wt% at 650°C) as well as its heating value. The low heating value (LHV) of syngas ranges between 18 and 26MJ/Nm 3 dry. The highest pyrolysis oil yield (33wt.%) was observed at 550°C and its LHV ranges between 12.5 and 14.5MJ/kg. Furthermore, only two out of the six produced chars respect the LHV limit set by the Italian environmental regulations for landfilling. The obtained results in terms of product distribution and their chemical-physical analyses provide useful information for plant scale-up. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hot Spot Initiation Patterns in Shocked Explosives and Propellants Recorded by Thermal Film.

DTIC Science & Technology

1980-12-02

8 PropellantsVRA-23andALTU-16 . . . . . ........ .. 9 PBXN - 106 Simulant . . . . . .. . . . . . . . . . . . . . 9 CONCLUSIONS...Enlargement (120X) Showing Crater Pattern With Charred Rim Produced By Fracture of Glass Beads in PBXN - 106 Simulant . . . . . 21 12 Model of Crater...explosives and high energy propellants as well as with an explo- sive ( PBXN - 106 ) simulant. The results of these tests are reported below. PRESSED TNT. Figure

Analysis of HEMCL Railgun Insulator Damage

DTIC Science & Technology

2006-06-01

pyrolytic epoxy degradation and glass fiber softening and liquification in the insulator, it is determined that rail-to-rail plasmas are present behind...produces epoxy decomposition products in the form of gases, oils , waxes and chars solid (heavily cross-linked residues) [4]. The nature of the... pyrolytic decomposition product (wax) of the epoxy as in the fired specimens. Figures 6 and 7 are typical examples of glass fiber softening and

Novel integrated mechanical biological chemical treatment (MBCT) systems for the production of levulinic acid from fraction of municipal solid waste: A comprehensive techno-economic analysis.

PubMed

Sadhukhan, Jhuma; Ng, Kok Siew; Martinez-Hernandez, Elias

2016-09-01

This paper, for the first time, reports integrated conceptual MBCT/biorefinery systems for unlocking the value of organics in municipal solid waste (MSW) through the production of levulinic acid (LA by 5wt%) that increases the economic margin by 110-150%. After mechanical separation recovering recyclables, metals (iron, aluminium, copper) and refuse derived fuel (RDF), lignocelluloses from remaining MSW are extracted by supercritical-water for chemical valorisation, comprising hydrolysis in 2wt% dilute H2SO4 catalyst producing LA, furfural, formic acid (FA), via C5/C6 sugar extraction, in plug flow (210-230°C, 25bar, 12s) and continuous stirred tank (195-215°C, 14bar, 20min) reactors; char separation and LA extraction/purification by methyl isobutyl ketone solvent; acid/solvent and by-product recovery. The by-product and pulping effluents are anaerobically digested into biogas and fertiliser. Produced biogas (6.4MWh/t), RDF (5.4MWh/t), char (4.5MWh/t) are combusted, heat recovered into steam generation in boiler (efficiency: 80%); on-site heat/steam demand is met; balance of steam is expanded into electricity in steam turbines (efficiency: 35%). Copyright © 2016 Elsevier Ltd. All rights reserved.

Empirical and Bayesian approaches to fossil-only divergence times: A study across three reptile clades.

PubMed

Turner, Alan H; Pritchard, Adam C; Matzke, Nicholas J

2017-01-01

Estimating divergence times on phylogenies is critical in paleontological and neontological studies. Chronostratigraphically-constrained fossils are the only direct evidence of absolute timing of species divergence. Strict temporal calibration of fossil-only phylogenies provides minimum divergence estimates, and various methods have been proposed to estimate divergences beyond these minimum values. We explore the utility of simultaneous estimation of tree topology and divergence times using BEAST tip-dating on datasets consisting only of fossils by using relaxed morphological clocks and birth-death tree priors that include serial sampling (BDSS) at a constant rate through time. We compare BEAST results to those from the traditional maximum parsimony (MP) and undated Bayesian inference (BI) methods. Three overlapping datasets were used that span 250 million years of archosauromorph evolution leading to crocodylians. The first dataset focuses on early Sauria (31 taxa, 240 chars.), the second on early Archosauria (76 taxa, 400 chars.) and the third on Crocodyliformes (101 taxa, 340 chars.). For each dataset three time-calibrated trees (timetrees) were calculated: a minimum-age timetree with node ages based on earliest occurrences in the fossil record; a 'smoothed' timetree using a range of time added to the root that is then averaged over zero-length internodes; and a tip-dated timetree. Comparisons within datasets show that the smoothed and tip-dated timetrees provide similar estimates. Only near the root node do BEAST estimates fall outside the smoothed timetree range. The BEAST model is not able to overcome limited sampling to correctly estimate divergences considerably older than sampled fossil occurrence dates. Conversely, the smoothed timetrees consistently provide node-ages far older than the strict dates or BEAST estimates for morphologically conservative sister-taxa when they sit on long ghost lineages. In this latter case, the relaxed-clock model appears to be correctly moderating the node-age estimate based on the limited morphological divergence. Topologies are generally similar across analyses, but BEAST trees for crocodyliforms differ when clades are deeply nested but contain very old taxa. It appears that the constant-rate sampling assumption of the BDSS tree prior influences topology inference by disfavoring long, unsampled branches.

Empirical and Bayesian approaches to fossil-only divergence times: A study across three reptile clades

PubMed Central

Turner, Alan H.; Pritchard, Adam C.; Matzke, Nicholas J.

2017-01-01

Estimating divergence times on phylogenies is critical in paleontological and neontological studies. Chronostratigraphically-constrained fossils are the only direct evidence of absolute timing of species divergence. Strict temporal calibration of fossil-only phylogenies provides minimum divergence estimates, and various methods have been proposed to estimate divergences beyond these minimum values. We explore the utility of simultaneous estimation of tree topology and divergence times using BEAST tip-dating on datasets consisting only of fossils by using relaxed morphological clocks and birth-death tree priors that include serial sampling (BDSS) at a constant rate through time. We compare BEAST results to those from the traditional maximum parsimony (MP) and undated Bayesian inference (BI) methods. Three overlapping datasets were used that span 250 million years of archosauromorph evolution leading to crocodylians. The first dataset focuses on early Sauria (31 taxa, 240 chars.), the second on early Archosauria (76 taxa, 400 chars.) and the third on Crocodyliformes (101 taxa, 340 chars.). For each dataset three time-calibrated trees (timetrees) were calculated: a minimum-age timetree with node ages based on earliest occurrences in the fossil record; a ‘smoothed’ timetree using a range of time added to the root that is then averaged over zero-length internodes; and a tip-dated timetree. Comparisons within datasets show that the smoothed and tip-dated timetrees provide similar estimates. Only near the root node do BEAST estimates fall outside the smoothed timetree range. The BEAST model is not able to overcome limited sampling to correctly estimate divergences considerably older than sampled fossil occurrence dates. Conversely, the smoothed timetrees consistently provide node-ages far older than the strict dates or BEAST estimates for morphologically conservative sister-taxa when they sit on long ghost lineages. In this latter case, the relaxed-clock model appears to be correctly moderating the node-age estimate based on the limited morphological divergence. Topologies are generally similar across analyses, but BEAST trees for crocodyliforms differ when clades are deeply nested but contain very old taxa. It appears that the constant-rate sampling assumption of the BDSS tree prior influences topology inference by disfavoring long, unsampled branches. PMID:28187191

Aerogel and xerogel composites for use as carbon anodes

DOEpatents

Cooper, John F.; Tillotson, Thomas M.; Hrubesh, Lawrence W.

2010-10-12

A method for forming a reinforced rigid anode monolith and fuel and product of such method. The method includes providing a solution of organic aerogel or xerogel precursors including at least one of a phenolic resin, phenol (hydroxybenzene), resorcinol(1,3-dihydroxybenzene), or catechol(1,2-dihydroxybenzene); at least one aldehyde compound selected from the group consisting of formaldehyde, acetaldehyde, and furfuraldehyde; and an alkali carbonate or phosphoric acid catalyst; adding internal reinforcement materials comprising carbon to said precursor solution to form a precursor mixture; gelling said precursor mixture to form a composite gel; drying said composite gel; and pyrolyzing said composite gel to form a wettable aerogel/carbon composite or a wettable xerogel/carbon composite, wherein said composites comprise chars and said internal reinforcement materials, and wherein said composite is suitable for use as an anode with the chars being fuel capable of being combusted in a molten salt electrochemical fuel cell in the range from 500 C to 800 C to produce electrical energy. Additional methods and systems/compositions are also provided.

Properties of oil and char derived from slow pyrolysis of Tetraselmis chui.

PubMed

Grierson, Scott; Strezov, Vladimir; Shah, Pushan

2011-09-01

Pyrolysis of biomass is a means to industrially manufacture renewable oil and gas, in addition to biochar for soil amendment and long-term carbon fixation. In this work, oil and char derived from the slow pyrolysis of the unicellular marine diatom Tetraselmis chui are analysed using a variety of techniques. The pyrolytic oil fraction exhibits a wide variety of fatty acids, alkanes, alkenes, amides, aldehydes, terpenes, pyrrolidinines, phytol and phenols, with a high heating value (HHV) of 28 MJ/kg. The biochar produced has a HHV of 14.5 MJ/kg and reveals a number of properties that are potentially valuable from an agronomic point of view, including high cation exchange capacity (CEC), large concentration of N, and a low C:N ratio. The quantity of C in T. chui biochar that can be expected to stabilise in soil amounts to approximately 9%/wt of the original feedstock, leading to a potential net reduction in atmospheric CO(2). Copyright © 2011 Elsevier Ltd. All rights reserved.

Production of Substitute Natural Gas from Coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrew Lucero

2009-01-31

The goal of this research program was to develop and demonstrate a novel gasification technology to produce substitute natural gas (SNG) from coal. The technology relies on a continuous sequential processing method that differs substantially from the historic methanation or hydro-gasification processing technologies. The thermo-chemistry relies on all the same reactions, but the processing sequences are different. The proposed concept is appropriate for western sub-bituminous coals, which tend to be composed of about half fixed carbon and about half volatile matter (dry ash-free basis). In the most general terms the process requires four steps (1) separating the fixed carbon frommore » the volatile matter (pyrolysis); (2) converting the volatile fraction into syngas (reforming); (3) reacting the syngas with heated carbon to make methane-rich fuel gas (methanation and hydro-gasification); and (4) generating process heat by combusting residual char (combustion). A key feature of this technology is that no oxygen plant is needed for char combustion.« less

Thermogravimetric and kinetic study of Pinyon pine in the various gases.

PubMed

Kim, Seung-Soo; Shenoy, Alok; Agblevor, Foster A

2014-03-01

As a renewable resource, Pinyon pine can be converted into bio-oil, gas, and char through pyrolysis. It is known that recycling of the non-condensable gases, which are produced by fast pyrolysis, can increase liquid yield and decrease char yield. In this study, pyrolysis characteristics and kinetics of Pinyon pine were investigated in TGA using simulated non-condensable gases (N2, H2/N2, H2/CO2, and He/CO/H2). The apparent activation energy of Pinyon pine increased from 43.9 to 160.3kJ mol(-1) with increasing pyrolysis conversion from 5% to 95% in pure nitrogen, and reaction order was 1.35. When hydrogen (H2) and carbon monoxide (CO) mixtures were used as simulated gases, the maximum degradation temperature and activation energy decreased by 4-11°C and 6.1-10.2kJ/mol, respectively. The results show that recycling of non-condensable gases could positively influence the fast pyrolysis of biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

Arc Jet Test and Analysis of Asbestos Free Solid Rocket Motor Nozzle Dome Ablative Materials

NASA Technical Reports Server (NTRS)

Clayton, J. Louie

2017-01-01

Asbestos free solid motor internal insulation samples were recently tested at the MSFC Hyperthermal Arc Jet Facility. Objectives of the test were to gather data for solid rocket motor analog characterization of ablative and in-depth thermal performance of rubber materials subject to high enthalpy/pressure flow conditions. Tests were conducted over a range of convective heat fluxes for both inert and chemically reactive sub-sonic free stream gas flow. Active instrumentation included use of total calorimeters, in-depth thermocouples, and a surface pyrometer for in-situ surface temperature measurement. Post-test sample forensics involved determination of eroded depth, charred depth, total sample weight loss, and documentation of the general condition of the eroded profile. A complete Charring Material Ablator (CMA) style aero thermal analysis was conducted for the test matrix and results compared to the measured data. In general, comparisons were possible for a number of the cases and the results show a limited predictive ability to model accurately both the ablative response and the in-depth temperature profiles. Lessons learned and modeling recommendations are made regarding future testing and modeling improvements that will increase understanding of the basic chemistry/physics associated with the complicated material ablation process of rubber materials.

Investigation of mineral transformations and ash deposition during staged combustion. Quarterly technical progress report, April 1, 1997--June 30, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harb, J.N.

This report describes work performed in the fifteenth quarter of a fundamental study to examine the effect of staged combustion on ash formation and deposition. Efforts this quarter included addition of a new cyclone for improved particle sampling and modification of the existing sampling probe. Particulate samples were collected under a variety of experimental conditions for both coals under investigation. Deposits formed from the Black Thunder coal were also collected. Particle size and composition from the Pittsburgh No. 8 ash samples support previously reported results. In addition, the authors ability to distinguish char/ash associations has been refined and applied tomore » a variety of ash samples from this coal. The results show a clear difference between the behavior of included and excluded pyrite, and provide insight into the extent of pyrite oxidation. Ash samples from the Black Thunder coal have also been collected and analyzed. Results indicate a significant difference in the particle size of {open_quotes}unclassifiable{close_quotes} particles for ash formed during staged combustion. A difference in composition also appears to be present and is currently under investigation. Finally, deposits were collected under staged conditions for the Black Thunder coal. Specifically, two deposits were formed under similar conditions and allowed to mature under either reducing or oxidizing conditions in natural gas. Differences between the samples due to curing were noted. In addition, both deposits showed skeletal ash structures which resulted from in-situ burnout of the char after deposition.« less

User Interface to an ICAI System That Teaches Discrete Math

DTIC Science & Technology

1990-06-01

lesson; otherwise, returns the user to the lesson. */ if (!frornlsn) menudeino); else exit((); 90 FUNCTION . flashcards CALLED BY: tools CALLS...char opchar[5j; /* OR, AND, IMPLIES or 1FF * char anchar[5J: /* User’s response: Either TRUE or FALSE * char outputch[ 15]; /* Flashcard that is...y values for the user’s screen. */ maxx = getmaxxo ; maxy = getmaxyo ; /* Sets the coordinates for the flashcard . */ left = maxx/6 right = maxx* 5/6

A new mathematical solution for predicting char activation reactions

USGS Publications Warehouse

Rafsanjani, H.H.; Jamshidi, E.; Rostam-Abadi, M.

2002-01-01

The differential conservation equations that describe typical gas-solid reactions, such as activation of coal chars, yield a set of coupled second-order partial differential equations. The solution of these coupled equations by exact analytical methods is impossible. In addition, an approximate or exact solution only provides predictions for either reaction- or diffusion-controlling cases. A new mathematical solution, the quantize method (QM), was applied to predict the gasification rates of coal char when both chemical reaction and diffusion through the porous char are present. Carbon conversion rates predicted by the QM were in closer agreement with the experimental data than those predicted by the random pore model and the simple particle model. ?? 2002 Elsevier Science Ltd. All rights reserved.

Pyrolysis of waste tyres: a review.

PubMed

Williams, Paul T

2013-08-01

Approximately 1.5 billion tyres are produced each year which will eventually enter the waste stream representing a major potential waste and environmental problem. However, there is growing interest in pyrolysis as a technology to treat tyres to produce valuable oil, char and gas products. The most common reactors used are fixed-bed (batch), screw kiln, rotary kiln, vacuum and fluidised-bed. The key influence on the product yield, and gas and oil composition, is the type of reactor used which in turn determines the temperature and heating rate. Tyre pyrolysis oil is chemically very complex containing aliphatic, aromatic, hetero-atom and polar fractions. The fuel characteristics of the tyre oil shows that it is similar to a gas oil or light fuel oil and has been successfully combusted in test furnaces and engines. The main gases produced from the pyrolysis of waste tyres are H(2), C(1)-C(4) hydrocarbons, CO(2), CO and H(2)S. Upgrading tyre pyrolysis products to high value products has concentrated on char upgrading to higher quality carbon black and to activated carbon. The use of catalysts to upgrade the oil to a aromatic-rich chemical feedstock or the production of hydrogen from waste tyres has also been reported. Examples of commercial and semi-commercial scale tyre pyrolysis systems show that small scale batch reactors and continuous rotary kiln reactors have been developed to commercial scale. Copyright © 2013 Elsevier Ltd. All rights reserved.

Impact of petrographic properties on the burning behavior of pulverized coal using a drop tube furnace

DOE Office of Scientific and Technical Information (OSTI.GOV)

S. Biswas; N. Choudhury; S. Ghosal

The combustion behavior of three Indian coals of different rank with wide variation in ash content and maceral compositions were studied using a drop tube furnace (DTF). Each coal was pulverized into a specific size (80% below 200 mesh) and fed into the DTF separately. The DTF runs were carried out under identical conditions for all of the coals. The carbon burnout was found out from the chemical analyses of the feed coals and the char samples collected from different ports of the DTF. Char morphology analyses was carried on the burnout residues of the top port. The top portmore » results show better burnout of the lower rank coals which however was not observed in the last port. An attempt has been made to account for this variation in terms of rank and petrographic parameters of the respective coals. 20 refs., 1 fig., 6 tabs.« less

Fireproofing and heat insulating performance improvement of EG/ATH modified intumescent flame retardant coating treated under Co-60 radiation

NASA Astrophysics Data System (ADS)

Zhang, Yuehong; Luan, Weiling; Jiang, Tao

2017-12-01

New intumescent flame retardant (IFR) coatings with different fire retardants were prepared in this paper. Expandable graphite (EG) and Aluminium hydroxide (ATH) were respectively added into the conventional IFR coating system, which included ammonium polyphosphate (APP) / pentaerythritol (PER) / melamine (MEL). The fireproofing time and heat insulating properties of the additives acted as fire retardants were investigated via thermogravimetry analysis (TGA) and fire resistance test of homemade big panel test. The morphology of the char layer structure was achieved by scanning electron microscopy (SEM). The highlight of the paper was that the coating samples were pretreated under Co-60 radiation. The influence of radiation on the fire resistance time and char layer height was investigated. The results showed that the prepared IFR coatings can be used in Co-60 radiation for more than 90 min when encountering fire. It would be a reference for radiation shielding in nuclear environment.

Understanding the fate of black (pyrogenic) carbon in soil: Preliminary results from a long term field trial

NASA Astrophysics Data System (ADS)

Meredith, Will; Ascough, Philippa; Bird, Michael; Large, David; Shen, Licheng; Snape, Colin

2014-05-01

Black carbon (BC, also known as pyrogenic carbon) is an 'inert' form of carbon and has been proposed as a means of long-term carbon sequestration, particularly by amending soils and sediments with BC known as biochar. While there is abundant anecdotal evidence of biochar stability over extended timescales it is essential to gain a greater understanding of the degree and mechanisms of biochar degradation in the environment. This study aims to quantitatively assess the stability of biochar by investigating samples from field degradation trials first buried during 2009 in a tropical soil, and recovered after 12 and 36 month intervals. Catalytic hydropyrolysis (HyPy) is a novel analytical tool for the isolation of BC [1] in which high hydrogen pressure (150 bar) and a sulphided Mo catalyst reductively remove the non-BC fraction of the chars, and so isolate the most stable portion of the biochar, defined as BC(HyPy). This method also allows for the non-BC(HyPy) fraction of a sample, which from charcoal is known to include small ring PAHs (<7 rings) of pyrogenic origin to be recovered for molecular characterisation by GC-MS [2]. Biochars made from algae, sugarcane bagasse, and beech wood at 305, 414 and 512°C were emplaced under a variety of conditions allowing variables such as leaf cover, soil depth and pH to be investigated. Char stability (as measured by BC(HyPy) content) is dependent on both the feedstock and temperature of formation. HyPy is known to discriminate (in terms of BC isolation) against low temperature chars, composed of relatively small aromatic clusters [1], resulting in the low BC(HyPy) contents reported for the 305°C chars. Fresh charcoals, and those not subject to environmental degradation have display a similar distribution of aromatic clusters in the non-BC(HyPy) fraction, with 2 to 7 ring PAHs abundant [2]. However, environmentally degraded charcoals such as that from a Chinese river sediment, and an Australian river estuary [3] show a more restricted distribution with markedly fewer 2- and 3- ring PAH structures apparent. This may be evidence for the partial solubilisation of the charcoal as observed for a forest soil [4] and suggested as a mechanism for the transport of BC to the oceans [5], implying that BC cycling could be faster than previously thought [6]. Longer term field trials will be required (analysis of the 36 month samples) to observe systematic changes in the PAH distribution of the non-BCC(HyPy) fractions isolated form aged chars, although natural analogues with a better constrained environmental history may also be useful. [1] Meredith, W. et al., 2012. Geochimica et Cosmochimica Acta 97, 131-147. [2] Ascough, P.L. et al., 2010. Radiocarbon 52, 1336-1350. [3] Lockhart, R.S. et al., 2013. Journal of Analytical and Applied Pyrolysis 104, 640-652. [4] Hockaday, W.C. et al., 2007. Geochimica et Cosmochimica Acta 71, 3432-3445. [5] Jaffe, R. et al., 2013. Science 340, 345-347. [6] Zimmerman, M. et al., 2012. Global Change Biology 18, 3306-3316.

Pyrolysis process for producing fuel gas

NASA Technical Reports Server (NTRS)

Serio, Michael A. (Inventor); Kroo, Erik (Inventor); Wojtowicz, Marek A. (Inventor); Suuberg, Eric M. (Inventor)

2007-01-01

Solid waste resource recovery in space is effected by pyrolysis processing, to produce light gases as the main products (CH.sub.4, H.sub.2, CO.sub.2, CO, H.sub.2O, NH.sub.3) and a reactive carbon-rich char as the main byproduct. Significant amounts of liquid products are formed under less severe pyrolysis conditions, and are cracked almost completely to gases as the temperature is raised. A primary pyrolysis model for the composite mixture is based on an existing model for whole biomass materials, and an artificial neural network models the changes in gas composition with the severity of pyrolysis conditions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sai, P.M.S.; Ahmed, J.; Krishnaiah, K.

Activated carbon is produced from coconut shell char using steam or carbon dioxide as the reacting gas in a 100 mm diameter fluidized bed reactor. The effect of process parameters such as reaction time, fluidizing velocity, particle size, static bed height, temperature of activation, fluidizing medium, and solid raw material on activation is studied. The product is characterized by determination of iodine number and BET surface area. The product obtained in the fluidized bed reactor is much superior in quality to the activated carbons produced by conventional processes. Based on the experimental observations, the optimum values of process parameters aremore » identified.« less

Acidification with nitric acid improves chemical characteristics and reduces phytotoxicity of alkaline chars.

PubMed

Fornes, Fernando; Belda, Rosa Maria

2017-04-15

Charred organic matter is recently receiving attention for its potential use as soilless growth medium. However, depending on its origin and on the manufacturing technology, it can result toxic for plants. This fact implies that a detoxifying treatment ought to be devised in order to reclaim char in this way. We have studied three materials which combine these factors: two pyrolyzed biochars, one from forest waste (BCH-FW) and another from olive mill waste (BCH-OMW), and one hydrothermally carbonized hydrochar from forest waste (HYD-FW). These materials are suspicious of phytotoxicity due to their high pH, high salinity, or presence of organic toxics. For these new materials, it is mandatory to select fast and reliable bioassays to predict their potential phytotoxicity. In order to achieve this goal water extracts of the three chars were subjected to bioassays of seed germination and bioassays of seedling growth in hydroponic conditions. The biochar from olive mill waste and the hydrochar, but not the biochar from forest waste, showed considerable phytotoxicity as seed germination and plant growth were negatively affected (e.g. BCH-OMW reduced seed germination by 80% and caused early seedling death). In order to adjust pH and electrical conductivity for plant growth, treatments of acidification and salt leaching with optimal diluted HNO 3 solutions (0.3 N, 0.2 N, and 0.75 N for BCH-OMW, BCH-FW, and HYD-FW, respectively) as calculated from titration curves, were conducted. The acid treatment reduced electrical conductivity in BCH-OMW (from 9.2 to 4.5 dS m -1 ), pH (maximum in BCH-FW from 9.6 to 6.2) and water soluble carbonaceous compounds (maximum in HYD-FW from 5969 to 2145 mg kg -1 ) in the three chars, and increased N content (maximum in BCH-OMW from 50 to 6342 mg kg -1 ) in the three chars. Bioassays on acid-treated chars demonstrated the absence of phytotoxicity and even stimulation of seedling growth over the control (increase of 86% and 56% for BCH-FW and HYD-FW, respectively). We conclude that acidification of chars with diluted HNO 3 is a viable technique to conform chars to standards for plant growth purposes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preference for cannibalism and ontogenetic constraints in competitive ability of piscivorous top predators.

PubMed

Byström, Pär; Ask, Per; Andersson, Jens; Persson, Lennart

2013-01-01

Occurrence of cannibalism and inferior competitive ability of predators compared to their prey have been suggested to promote coexistence in size-structured intraguild predation (IGP) systems. The intrinsic size-structure of fish provides the necessary prerequisites to test whether the above mechanisms are general features of species interactions in fish communities where IGP is common. We first experimentally tested whether Arctic char (Salvelinus alpinus) were more efficient as a cannibal than as an interspecific predator on the prey fish ninespine stickleback (Pungitius pungitius) and whether ninespine stickleback were a more efficient competitor on the shared zooplankton prey than its predator, Arctic char. Secondly, we performed a literature survey to evaluate if piscivores in general are more efficient as cannibals than as interspecific predators and whether piscivores are inferior competitors on shared resources compared to their prey fish species. Both controlled pool experiments and outdoor pond experiments showed that char imposed a higher mortality on YOY char than on ninespine sticklebacks, suggesting that piscivorous char is a more efficient cannibal than interspecific predator. Estimates of size dependent attack rates on zooplankton further showed a consistently higher attack rate of ninespine sticklebacks compared to similar sized char on zooplankton, suggesting that ninespine stickleback is a more efficient competitor than char on zooplankton resources. The literature survey showed that piscivorous top consumers generally selected conspecifics over interspecific prey, and that prey species are competitively superior compared to juvenile piscivorous species in the zooplankton niche. We suggest that the observed selectivity for cannibal prey over interspecific prey and the competitive advantage of prey species over juvenile piscivores are common features in fish communities and that the observed selectivity for cannibalism over interspecific prey has the potential to mediate coexistence in size structured intraguild predation systems.

Preference for Cannibalism and Ontogenetic Constraints in Competitive Ability of Piscivorous Top Predators

PubMed Central

Byström, Pär; Ask, Per; Andersson, Jens; Persson, Lennart

2013-01-01

Occurrence of cannibalism and inferior competitive ability of predators compared to their prey have been suggested to promote coexistence in size-structured intraguild predation (IGP) systems. The intrinsic size-structure of fish provides the necessary prerequisites to test whether the above mechanisms are general features of species interactions in fish communities where IGP is common. We first experimentally tested whether Arctic char (Salvelinus alpinus) were more efficient as a cannibal than as an interspecific predator on the prey fish ninespine stickleback (Pungitius pungitius) and whether ninespine stickleback were a more efficient competitor on the shared zooplankton prey than its predator, Arctic char. Secondly, we performed a literature survey to evaluate if piscivores in general are more efficient as cannibals than as interspecific predators and whether piscivores are inferior competitors on shared resources compared to their prey fish species. Both controlled pool experiments and outdoor pond experiments showed that char imposed a higher mortality on YOY char than on ninespine sticklebacks, suggesting that piscivorous char is a more efficient cannibal than interspecific predator. Estimates of size dependent attack rates on zooplankton further showed a consistently higher attack rate of ninespine sticklebacks compared to similar sized char on zooplankton, suggesting that ninespine stickleback is a more efficient competitor than char on zooplankton resources. The literature survey showed that piscivorous top consumers generally selected conspecifics over interspecific prey, and that prey species are competitively superior compared to juvenile piscivorous species in the zooplankton niche. We suggest that the observed selectivity for cannibal prey over interspecific prey and the competitive advantage of prey species over juvenile piscivores are common features in fish communities and that the observed selectivity for cannibalism over interspecific prey has the potential to mediate coexistence in size structured intraguild predation systems. PMID:23894650

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ejiofor, J.U.; Reddy, R.G.

The influence of microporous particulate carbon char on the mechanical, thermal, and tribological properties of wear-resistant Al-13.5Si-2.5Mg alloy composites was studied. Large increases in surface area due to the formation of micropores in coconut shell chars were achieved by high-temperature activation under CO{sub 2} gas flow. Activated char particles at 0.02 V{sub f} were used to reinforce the alloy. The composites were fabricated via a double-compaction reaction sintering technique under vacuum at a compaction pressure of 250 MPa and sintering temperature of 600 C. At more than 35% burn-off of the carbon chars at the temperature of activation, 915 C,more » the total surface area remained virtually unaffected. The ultimate tensile strength and hardness decreased by 23% and 6%, respectively; with increasing surface area of the reinforcement from 123 to 821 m{sup 2} g{sup {minus}1}. The yield strength and the percentage of elongation decreased by a factor of 2 and 5, respectively. No significant change in sliding wear rate was observed but the coefficient of friction increased by 13% (0.61 to 0.69). The coefficient of linear thermal expansion was reduced by 16% (11.7 {times} 10{sup {minus}6} to 9.8 {times} 10{sup {minus}6} C{sup {minus}1}), and remained unaffected at more than 35% burn-off. Energy-dispersive spectrometry of the particles of the activated chars showed that oxides of potassium and copper coated the open surfaces. Failure at the matrix-char interface was observed, and this was attributed to localized presence of oxides at the interfaces as identified by electron probe microanalysis. Poor wetting of the oxides by magnesium at the sintering conditions resulted in formation of weak matrix-char interface bonds.« less

The effectiveness of spent coffee grounds and its biochar on the amelioration of heavy metals-contaminated water and soil using chemical and biological assessments.

PubMed

Kim, Min-Suk; Min, Hyun-Gi; Koo, Namin; Park, Jeongsik; Lee, Sang-Hwan; Bak, Gwan-In; Kim, Jeong-Gyu

2014-12-15

Spent coffee grounds (SCG) and charred spent coffee grounds (SCG-char) have been widely used to adsorb or to amend heavy metals that contaminate water or soil and their success is usually assessed by chemical analysis. In this work, the effects of SCG and SCG-char on metal-contaminated water and soil were evaluated using chemical and biological assessments; a phytotoxicity test using bok choy (Brassica campestris L. ssp. chinensis Jusl.) was conducted for the biological assessment. When SCG and SCG-char were applied to acid mine drainage, the heavy metal concentrations were decreased and the pH was increased. However, for SCG, the phytotoxicity increased because a massive amount of dissolved organic carbon was released from SCG. In contrast, SCG-char did not exhibit this phenomenon because any easily released organic matter was removed during pyrolysis. While the bioavailable heavy metal content decreased in soils treated with SCG or SCG-char, the phytotoxicity only rose after SCG treatment. According to our statistical methodology, bioavailable Pb, Cu and As, as well as the electrical conductivity representing an increase in organic content, affected the phytotoxicity of soil. Therefore, applying SCG during environment remediation requires careful biological assessments and evaluations of the efficiency of this remediation technology. Copyright © 2014 Elsevier Ltd. All rights reserved.

Changes of chromium speciation and organic matter during low-temperature pyrolysis of tannery sludge.

PubMed

Zhou, Jianjun; Ma, Hongrui; Gao, Mao; Sun, Wenyue; Zhu, Chao; Chen, Xiangping

2018-01-01

The application or disposal of char derived from tannery sludge is directly influenced by the mobility and bioavailability of Cr during pyrolysis process. This study focused on the changes of Cr speciation and organic matter in tannery sludge during low-temperature pyrolysis (100-400 °C) to evaluate the toxicity of char in terms of the leaching possibility of Cr. The results showed that (1) lower char yield and more porous structure were observed after pyrolysis. (2) Higher pyrolysis temperature increased Cr content in the char; however, Cr in this case was converted into the residual fraction which minimized its bioavailability therefore lowers its potential risk to the environment. (3) Organic matters in the acid and alkali leachates were mainly humic acid-like substance, and condensed organic matter might appear at 200 °C and then destruct. (4) Despite the comparatively high content of Cr in the char, the leaching toxicity of char was within the security range according to the national standard of China. The Cr content in the acid and alkali leachates decreased to the range of 16.5-35.3 and 0.2-6.8 mg/L, respectively. It was suggested that the potential toxicity of tannery sludge from Cr could be reduced before utilization or disposal by pyrolysis, especially under 400 °C.

Pyrolysis of Lantana camara and Mimosa pigra: Influences of temperature, other process parameters and incondensable gas evolution on char yield and higher heating value.

PubMed

Mundike, Jhonnah; Collard, François-Xavier; Görgens, Johann F

2017-11-01

Pyrolysis of invasive non-indigenous plants, Lantana camara (LC) and Mimosa pigra (MP) was conducted at milligram-scale for optimisation of temperature, heating rate and hold time on char yield and higher heating value (HHV). The impact of scaling-up to gram-scale was also studied, with chromatography used to correlate gas composition with HHV evolution. Statistically significant effects of temperature on char yield and HHV were obtained, while heating rate and hold time effects were insignificant. Milligram-scale maximised HHVs were 30.03MJkg -1 (525°C) and 31.01MJkg -1 (580°C) for LC and MP, respectively. Higher char yields and HHVs for MP were attributed to increased lignin content. Scaling-up promoted secondary char formation thereby increasing HHVs, 30.82MJkg -1 for LC and 31.61MJkg -1 for MP. Incondensable gas analysis showed that temperature increase beyond preferred values caused dehydrogenation that decreased HHV. Similarly, CO evolution profile explained differences in optimal HHV temperatures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Pyrolysis of polyethylene mixed with paper and wood: Interaction effects on tar, char and gas yields.

PubMed

Grieco, E M; Baldi, G

2012-05-01

In the present study the interactions between the main constituents of the refuse derived fuel (plastics, paper, and wood) during pyrolysis were studied. Binary mixtures of polyethylene-paper and polyethylene/sawdust have been transformed into pellets and pyrolyzed. Various mixtures with different composition were analyzed and pyrolysis products (tar, gas, and char) were collected. The mixtures of wood/PE and paper/PE have a different behavior. The wood/PE mixtures showed a much reduced interaction of the various compounds because the yields of pyrolysis products of the mixture can be predicted as linear combination of those of the pure components. On the contrary, a strong char yield increase was found at a low heating rate for paper/PE mixtures. In order to explain the results, the ability of wood and paper char to adsorb and convert the products of PE pyrolysis into was studied. Adsorption and desorption tests were performed on the char obtained by paper and wood by using n-hexadecane as a model compound for the heavy products of PE pyrolysis. Copyright © 2011 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yuan Zhang; Jin-hu Wu; Dong-ke Zhang

The cracking of oil refinery off-gas, simulated with a gas mixture containing methane (51%), ethylene (21.4%), ethane (21.1%), and propane (6.5%), over a coal char, petroleum coke, and quartz, respectively, has been studied in a fixed bed reactor. The experiments were performed at temperatures between 850 and 1000{sup o}C and at atmospheric pressure. The results show that the conversions of all species considered increased with increasing temperature. Ethane and propane completely decomposed over all three bed materials in the temperature range investigated. However, the higher initial conversion rates of methane and ethylene cracking at all temperatures were observed only overmore » the coal char and not on the petroleum coke and quartz, indicating a significant catalytic effect of the coal char on methane and ethylene cracking. Methane and ethylene conversions decreased with reaction time due to deactivation of the coal char by carbon deposition on the char surface and, in the later stage of a cracking experiment, became negative, suggesting that methane and ethylene had been formed during the cracking of ethane and propane. 16 refs., 13 figs., 2 tabs.« less

Pyrolysis for exploitation of biomasses selected for soil phytoremediation: Characterization of gaseous and solid products.

PubMed

Giudicianni, Paola; Pindozzi, Stefania; Grottola, Corinna Maria; Stanzione, Fernando; Faugno, Salvatore; Fagnano, Massimo; Fiorentino, Nunzio; Ragucci, Raffaele

2017-03-01

Biomasses to be used in the phytoremediation process are generally selected to match agronomic parameters and heavy metals uptake ability. A proper selection can be made greatly effective if knowledge of the properties of the residual char from pyrolysis is available to identify possible valorization routes. In this study a comparative analysis of the yields and characteristics of char obtained from slow pyrolysis of five uncontaminated biomasses (Populus nigra, Salix alba, Fraxinus oxyphylla, Eucalyptus occidentalis and Arundo donax) was carried out under steam atmosphere to better develop char porosity. Moreover, the dependence of the properties of solid residue on the process final temperature was studied for E. occidentalis in the temperature range of 688-967K. The results demonstrate that, among the studied biomasses, chars from P. nigra and E. occidentalis have to be preferred for applications regulated by surface phenomena given their highest surface area (270-300m 2 /g), whereas char from E. occidentalis is the best choice when the goal is to maximize energy recovery. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermal characteristics and surface morphology of char during co-pyrolysis of low-rank coal blended with microalgal biomass: Effects of Nannochloropsis and Chlorella.

PubMed

Wu, Zhiqiang; Yang, Wangcai; Yang, Bolun

2018-02-01

In this work, the influence of Nannochloropsis and Chlorella on the thermal behavior and surface morphology of char during the co-pyrolysis process were explored. Thermogravimetric and iso-conversional methods were applied to analyzing the pyrolytic and kinetic characteristics for different mass ratios of microalgae and low-rank coal (0, 3:1, 1:1, 1:3 and 1). Fractal theory was used to quantitatively determine the effect of microalgae on the morphological texture of co-pyrolysis char. The result indicated that both the Nannochloropsis and Chlorella promoted the release of volatile from low-rank coal. Different synergistic effects on the thermal parameters and yield of volatile were observed, which could be attributed to the different compositions in the Nannochloropsis and Chlorella and operating condition. The distribution of activation energies shows nonadditive characteristics. Fractal dimensions of the co-pyrolysis char were higher than the individual char, indicating the promotion of disordered degree due to the addition of microalgae. Copyright © 2017 Elsevier Ltd. All rights reserved.

Co-pyrolysis behaviors of saw dust and Shenfu coal in drop tube furnace and fixed bed reactor.

PubMed

Li, Shuaidan; Chen, Xueli; Wang, Li; Liu, Aibin; Yu, Guangsuo

2013-11-01

Co-pyrolysis behaviors of saw dust (SD) and Shenfu bituminous coal (SF) were studied in a drop tube furnace and a fixed bed reactor at different temperatures respectively. Six different biomass/coal ratios (B:C) were used. Compared the results with the calculated value obtained by the additional behavior, CO volume yields were lower while H2, CH4, CO2, volume yields were higher. Blend char yields had a good agreement with the calculated values, and their structures remained similar with SD and SF char's. Synergy effect occurred in gaseous phase, which was mainly caused by the secondary reactions. Compared the blend char yields in the drop tube furnace with those in the fixed bed reactor, the results showed the contacting way of biomass and coal particles had little influence on char yield in co-pyrolysis process. The reactivity index of blend char achieved the minimum at B:C=40:60 and the maximum at B:C=80:20. Copyright © 2013 Elsevier Ltd. All rights reserved.

Rapid co-pyrolysis of rice straw and a bituminous coal in a high-frequency furnace and gasification of the residual char.

PubMed

Yuan, Shuai; Dai, Zheng-hua; Zhou, Zhi-jie; Chen, Xue-li; Yu, Guang-suo; Wang, Fu-chen

2012-04-01

Rapid pyrolysis of rice straw (RS) and Shenfu bituminous coal (SB) separately, and rapid co-pyrolysis of RS/SB blends (mass ratio 1:4, 1:4, and 4:1), were carried out in a high-frequency furnace which can ensure both high heating rate and satisfying contact of fuel particles. Synergies between RS and SB during rapid co-pyrolysis were investigated. Intrinsic and morphological structures of residual char from co-pyrolysis, and their effects on gasification characteristics were also studied. Synergies occurred during rapid co-pyrolysis of RS and SB (RS/SB=1:4) resulting in decreasing char yields and increasing volatile yields. Synergies also happened during gasification of the char derived from co-pyrolysis of RS and SB with mass ratio of 1:4. The increased mass ratio of RS to SB did not only weaken synergies during co-pyrolysis, but significantly reduced the gasification rates of the co-pyrolysis char compared to the calculated values. Results can help to optimize co-conversion process of biomass/coal. Copyright © 2012 Elsevier Ltd. All rights reserved.

Intumescent coatings with improved properties for high-rise construction

NASA Astrophysics Data System (ADS)

Ustinov, Andrey; Zybina, Olga; Tanklevsky, Leonid; Lebedev, Vasily; Andreev, Andrey

2018-03-01

The paper overviews the way of creating intumescent fire-protective compositions with improved properties by adding nano-and micro-sized supplements into them. Intumescent paints are inert at low temperatures, and at higher temperatures they expand and degrade to provide a charred layer of low conductivity materials. The modified intumescent paints are able to form a more stable charred layer than the classical paints. The stability of a charred layer is crucial if the fire safety in high-rise construction must be secured, because a weak charred layer will not provide a required fire endurance for steel bearing structures and they will break down in case of fire. The fire-protective properties of modified intumescent paints were estimated using an electrical furnace. Also the way of thermal decomposition of the paints was studied with thermogravimetric analysis. Results show that modified intumescent paints form a charred layer with improved fire-protective properties; it can serve as a thermal barrier for a longer period of time. Thermogravimetric analysis confirms this fact showing that the temperatures of full thermal decay in case of modified paints are higher than those of non-modified paints.

Combustion of Coal Char Particles under Fluidized Bed Oxyfiring Conditions

NASA Astrophysics Data System (ADS)

Scala, Fabrizio; Chirone, Riccardo

In this work combustion of single coal char particles was studied at 850°C in a lab-scale fluidized bed under simulated oxyfiring conditions. The burning rate of the particles was followed as a function of time by continuously measuring the outlet CO and O2 concentrations. Some preliminary evaluations on the significance of homogeneous CO oxidation in the reactor and of carbon gasification by CO2 in the char were also carried out. Results showed that the carbon burning rate increases with oxygen concentration and char particle size. The particle temperature is approximately equal to the bed one up to an oxygen concentration of 2%, but it is considerably higher for larger oxygen concentrations. Both CO2 gasification of char and homogeneous CO oxidation are not negligible. The gasification reaction rate is slow and it is likely to be controlled by intrinsic kinetics. During purely gasification conditions the extent of carbon loss due to particle attrition by abrasion (estimated from the carbon mass balance) appears to be more important than under combustion conditions.

Promotion of hydrogen-rich gas and phenolic-rich bio-oil production from green macroalgae Cladophora glomerata via pyrolysis over its bio-char.

PubMed

Norouzi, Omid; Jafarian, Sajedeh; Safari, Farid; Tavasoli, Ahmad; Nejati, Behnam

2016-11-01

Conversion of Cladophora glomerata (C. glomerata) as a Caspian Sea's green macroalgae into gaseous, liquid and solid products was carried out via pyrolysis at different temperatures to determine its potential for bio-oil and hydrogen-rich gas production for further industrial utilization. Non-catalytic tests were performed to determine the optimum condition for bio-oil production. The highest portion of bio-oil was retrieved at 500°C. The catalytic test was performed using the bio-char derived at 500°C as a catalyst. Effect of the addition of the algal bio-char on the composition of the bio-oil and also gaseous products was investigated. Pyrolysis derived bio-char was characterized by BET, FESEM and ICP method to show its surface area, porosity, and presence of inorganic metals on its surface, respectively. Phenols were increased from 8.5 to 20.76area% by the addition of bio-char. Moreover, the hydrogen concentration and hydrogen selectivity were also enhanced by the factors of 1.37, 1.59 respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development and Verification of the Charring Ablating Thermal Protection Implicit System Solver

NASA Technical Reports Server (NTRS)

Amar, Adam J.; Calvert, Nathan D.; Kirk, Benjamin S.

2010-01-01

The development and verification of the Charring Ablating Thermal Protection Implicit System Solver is presented. This work concentrates on the derivation and verification of the stationary grid terms in the equations that govern three-dimensional heat and mass transfer for charring thermal protection systems including pyrolysis gas flow through the porous char layer. The governing equations are discretized according to the Galerkin finite element method with first and second order implicit time integrators. The governing equations are fully coupled and are solved in parallel via Newton's method, while the fully implicit linear system is solved with the Generalized Minimal Residual method. Verification results from exact solutions and the Method of Manufactured Solutions are presented to show spatial and temporal orders of accuracy as well as nonlinear convergence rates.

Development and Verification of the Charring, Ablating Thermal Protection Implicit System Simulator

NASA Technical Reports Server (NTRS)

Amar, Adam J.; Calvert, Nathan; Kirk, Benjamin S.

2011-01-01

The development and verification of the Charring Ablating Thermal Protection Implicit System Solver (CATPISS) is presented. This work concentrates on the derivation and verification of the stationary grid terms in the equations that govern three-dimensional heat and mass transfer for charring thermal protection systems including pyrolysis gas flow through the porous char layer. The governing equations are discretized according to the Galerkin finite element method (FEM) with first and second order fully implicit time integrators. The governing equations are fully coupled and are solved in parallel via Newton s method, while the linear system is solved via the Generalized Minimum Residual method (GMRES). Verification results from exact solutions and Method of Manufactured Solutions (MMS) are presented to show spatial and temporal orders of accuracy as well as nonlinear convergence rates.

Synthesis of improved phenolic and polyester resins

NASA Technical Reports Server (NTRS)

Delano, C. B.

1980-01-01

Thirty-seven cured phenolic resin compositions were prepared and tested for their ability to provide improved char residues and moisture resistance over state of the art epoxy resin composite matrices. Cyanate, epoxy novolac and vinyl ester resins were investigated. Char promoter additives were found to increase the anaerobic char yield at 800 C of epoxy novolacs and vinyl esters. Moisture resistant cyanate and vinyl ester compositions were investigated as composite matrices with Thornel 300 graphite fiber. A cyanate composite matrix provided state of the art composite mechanical properties before and after humidity exposure and an anaerobic char yield of 46 percent at 800 C. The outstanding moisture resistance of the matrix was not completely realized in the composite. Vinyl ester resins showed promise as candidates for improved composite matrix systems.

Investigation of the Minimum Deployment Time of a Foam/Fabric Composite Material.

DTIC Science & Technology

1980-09-01

Kevlar Fabric! use xperienced, trained personnel. The pres- Polyurethane Foam Composites. TR M-272/ADA076310 sure containers should be adequately...evaluated. High molecular ponent foam producing materials. (Polyurethanes, weight resin performed best because its solubility char- epoxies, phenolics , and...that was coated to a total Because earlier CERL tests had established the weight of about 10 oz/sq yd (237 gm/m 2 ). strength of Kevlar * fabric, it was

Engineering Geology and Geomorphology of Streambank Erosion. Report 3. The Application of Waterborne Geophysical Techniques in Fluvial Environments.

DTIC Science & Technology

1982-02-01

filters are frequency-discriminating instruments whose signal transmission char- acteristics are functions of frequency. Their basic purpose is to pass...sediment loads. The sediment particles block effective transmission of acoustic pulses so that meaningful reflections from the bottom are not received...structures such as dikes, bridge piers, piling, etc. Eddies, boils, and other forms of turbulence associated with streamflow produce significant amounts of

Combustion and NOx emissions in deep-air-staging combustion of char in a circulating fluidized bed

NASA Astrophysics Data System (ADS)

Gong, Zhiqiang; Wang, Zhentong; Wang, Lei; Du, Aixun

2017-10-01

Combustion and NOx emissions in deep-air-staging (with higher level secondary air (SA) injection) combustion of char have been investigated in a CFB test rig. A good fluidized condition and uniform temperature distribution can be achieved with injection of higher level SA. NOx emission decreases with injection of higher level SA and the reduction effect is more obvious at higher temperature. NOx emission decreases with combustion temperature increasing for char combustion.

Well-to-wheels analysis of fast pyrolysis pathways with the GREET model.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, J.; Elgowainy, A.; Palou-Rivera, I.

The pyrolysis of biomass can help produce liquid transportation fuels with properties similar to those of petroleum gasoline and diesel fuel. Argonne National Laboratory conducted a life-cycle (i.e., well-to-wheels [WTW]) analysis of various pyrolysis pathways by expanding and employing the Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model. The WTW energy use and greenhouse gas (GHG) emissions from the pyrolysis pathways were compared with those from the baseline petroleum gasoline and diesel pathways. Various pyrolysis pathway scenarios with a wide variety of possible hydrogen sources, liquid fuel yields, and co-product application and treatment methods were considered. Atmore » one extreme, when hydrogen is produced from natural gas and when bio-char is used for process energy needs, the pyrolysis-based liquid fuel yield is high (32% of the dry mass of biomass input). The reductions in WTW fossil energy use and GHG emissions relative to those that occur when baseline petroleum fuels are used, however, is modest, at 50% and 51%, respectively, on a per unit of fuel energy basis. At the other extreme, when hydrogen is produced internally via reforming of pyrolysis oil and when bio-char is sequestered in soil applications, the pyrolysis-based liquid fuel yield is low (15% of the dry mass of biomass input), but the reductions in WTW fossil energy use and GHG emissions are large, at 79% and 96%, respectively, relative to those that occur when baseline petroleum fuels are used. The petroleum energy use in all scenarios was restricted to biomass collection and transportation activities, which resulted in a reduction in WTW petroleum energy use of 92-95% relative to that found when baseline petroleum fuels are used. Internal hydrogen production (i.e., via reforming of pyrolysis oil) significantly reduces fossil fuel use and GHG emissions because the hydrogen from fuel gas or pyrolysis oil (renewable sources) displaces that from fossil fuel natural gas and the amount of fossil natural gas used for hydrogen production is reduced; however, internal hydrogen production also reduces the potential petroleum energy savings (per unit of biomass input basis) because the fuel yield declines dramatically. Typically, a process that has a greater liquid fuel yield results in larger petroleum savings per unit of biomass input but a smaller reduction in life-cycle GHG emissions. Sequestration of the large amount of bio-char co-product (e.g., in soil applications) provides a significant carbon dioxide credit, while electricity generation from bio-char combustion provides a large energy credit. The WTW energy and GHG emissions benefits observed when a pyrolysis oil refinery was integrated with a pyrolysis reactor were small when compared with those that occur when pyrolysis oil is distributed to a distant refinery, since the activities associated with transporting the oil between the pyrolysis reactors and refineries have a smaller energy and emissions footprint than do other activities in the pyrolysis pathway.« less

The Effect of Soil Warming on Decomposition of Biochar, Wood, and Bulk Soil Organic Carbon in Contrasting Temperate and Tropical Soils

NASA Astrophysics Data System (ADS)

Torn, Margaret; Tas, Neslihan; Reichl, Ken; Castanha, Cristina; Fischer, Marc; Abiven, Samuel; Schmidt, Michael; Brodie, Eoin; Jansson, Janet

2013-04-01

Biochar and wood are known to decay at different rates in soil, but the longterm effect of char versus unaltered wood inputs on soil carbon dynamics may vary by soil ecosystem and by their sensitivity to warming. We conducted an incubation experiment to explore three questions: (1) How do decomposition rates of char and wood vary with soil type and depth? (2) How vulnerable to warming are these slowly decomposing inputs? And (3) Do char or wood additions increase loss of native soil organic carbon (priming)? Soils from a Mediterranean grassland (Hopland Experimental Research Station, California) and a moist tropical forest (Tabunoco Forest, Puerto Rico) were collected from two soil depths and incubated at ambient temperature (14°C, 20°C for Hopland and Tabonuco respectively) and ambient +6°C. We added 13C-labeled wood and char (made from the wood at 450oC) to the soils and quantified CO2 and 13CO2 fluxes with continuous online carbon isotope measurements using a Cavity Ringdown Spectrometer (Picarro, Inc) for one year. As expected, in all treatments the wood decomposed much (about 50 times) more quickly than did the char amendment. With few exceptions, amendments placed in the surface soil decomposed more quickly than those in deeper soil, and in forest soil faster than that placed in grassland soil, at the same temperature. The two substrates were not very temperature sensitive. Both had Q10 less than 2 and char decomposition in particular was relatively insensitive to warming. Finally, the addition of wood caused a significant increase of roughly 30% in decomposition losses of the native soil organic carbon in the grassland and slightly less in forest. Char had only a slight positive priming effect but had a significant effect on microbial community. These results show that conversion of wood inputs to char through wildfire or intentional management will alter not only the persistence of the carbon in soil but also its temperature response and effect on microbial communities.

Carbon Nanotube Oscillator Surface Profiling Device and Method of Use

DTIC Science & Technology

2011-11-15

distance p. The constants A and B are the Hamaker constants, which depend on the materials of the two interacting bodies. The total vdW inter...wall CNT 45 with 2L1 =2L2 =150 A and a sample of specific material char- acterized with atomic density a, Hamaker constants A and B, and a friction

Synthesis of a Novel Phosphorus-Containing Flame Retardant Curing Agent and Its Application in Epoxy Resins.

PubMed

Zhang, Hongkun; Xu, Miaojun; Li, Bin

2016-03-01

A novel phosphorus-containing compound diphenyl-(2,5-dihydroxyphenyl)-phosphine oxide defined as DPDHPPO was synthesized and used as flame retardant and curing agent for epoxy resins (EP). The chemical structure was well characterized by Fourier transform infrared (FTIR) spectroscopy, 1H, 13C and 31P nuclear magnetic resonance. The flame retardant properties, combusting performances and thermal degradation behaviors of the cured epoxy resins were investigated by limiting oxygen index (LOI), vertical burning tests (UL-94), cone calorimeter and thermogravimetric analysis (TGA) tests. The morphologies and chemical compositions of char residues for cured epoxy resins were investigated by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), respectively. The water resistant properties were evaluated by putting the samples into distilled water at 70 degrees C for 168 h. The results revealed that the EP/40 wt% DPDHPPO/60 wt% PDA thermosets successfully passed UL-94 V-0 flammability rating and the LOI value was as high as 31.9%. The cone tests results revealed that the incorporation of DPDHPPO efficiently reduced the combustion parameters of epoxy resins thermosets, such as heat release rate (HRR), total heat release (THR) and so on. The TGA results indicated that the introduction of DPDHPPO promoted epoxy resins matrix decomposed ahead of time compared with that of pure EP and led to a higher char yield and thermal stability at high temperature. The morphological structures and analysis of XPS of char residues revealed that DPDHPPO benefited to the formation of a sufficient, compact and homogeneous char layer with rich flame retardant elements on the epoxy resins materials surface during combustion. After water resistance tests, EP/40 wt% DPDHPPO/60 wt% PDA thermosets still remained excellent flame retardancy, the moisture absorption of epoxy resins thermosets decreased with the increase of DPDHPPO contents in the thermosets due to the existing of P-C bonds and the rigid aromatic hydrophobic structure.

Synthesis and characterization of poly (dihydroxybiphenyl borate) with high char yield for high-performance thermosetting resins

NASA Astrophysics Data System (ADS)

Wang, Shujuan; Xing, Xiaolong; Li, Jian; Jing, Xinli

2018-01-01

The objective of the current work is to synthesize novel boron-containing polymers with excellent thermal resistance, and reveal the structure and the reason for the high char yield. Thus, poly (dihydroxybiphenyl borate) (PDDB) with a more rigid molecular chain, was successfully synthesized using 4,4‧-dihydroxybiphenyl and boric acid. Structural characterizations of the prepared PDDB were performed via NMR, FTIR, XPS, and XRD analyses. The results reveal that PDDB consists of aromatic, Phsbnd Osbnd B and Bsbnd Osbnd B structures as well as a small number of boron hydroxyl and phenolic hydroxyl groups. PDDB shows good solubility in strong polar solvents, which is of great importance for the modification of thermosetting resins. TGA combined with DSC were employed to evaluate the thermal properties of PDDB, and increases in the glass transition temperature (Tg) and char yield were observed with increased boron content. Tg and char yield of PDDB (800 °C, nitrogen atmosphere) reached up to 219 °C and 66.5%, respectively. PDDB was extensively characterized during pyrolysis to reveal the high char yield of PDDB. As briefly discussed, the boron oxide and boron carbide that formed during pyrolysis play a crucial role in the high char yield of PDDB, which reduces the release of volatile carbon dioxide and carbon. This research suggests that PDDB has great potential as a novel modified agent for the improvement of the comprehensive performance of thermosetting resins to broaden their applicability in the field of advanced composites.

2,4-D adsorption to biochars: effect of preparation conditions on equilibrium adsorption capacity and comparison with commercial activated carbon literature data.

PubMed

Kearns, J P; Wellborn, L S; Summers, R S; Knappe, D R U

2014-10-01

Batch isotherm experiments were conducted with chars to study adsorption of the herbicide 2,4-dichlorophenoxyacetic acid (2,4-D). Chars generated from corncobs, bamboo and wood chips in a laboratory pyrolyzer at 400-700 °C were compared with traditional kiln charcoals collected from villages in S/SE Asia and with activated carbons (ACs). 2,4-D uptake by laboratory chars obtained from bamboo and wood chips after 14 h of pyrolysis at 700 °C, from wood chips after 96 h of pyrolysis at 600 °C, and one of the field-collected chars (basudha) was comparable to ACs. H:C and O:C ratios declined with pyrolysis temperature and duration while surface area increased to >500 m(2)/g. Increasing pyrolysis intensity by increasing temperature and/or duration of heating was found to positively influence adsorption capacity yield (mg(2,4-D/g(feedstock))) over the range of conditions studied. Economic analysis showed that high temperature chars can be a cost-effective alternative to ACs for water treatment applications. Copyright © 2014 Elsevier Ltd. All rights reserved.

Valorization of algal waste via pyrolysis in a fixed-bed reactor: Production and characterization of bio-oil and bio-char.

PubMed

Aboulkas, A; Hammani, H; El Achaby, M; Bilal, E; Barakat, A; El Harfi, K

2017-11-01

The aim of the present work is to develop processes for the production of bio-oil and bio-char from algae waste using the pyrolysis at controlled conditions. The pyrolysis was carried out at different temperatures 400-600°C and different heating rates 5-50°C/min. The algal waste, bio-oil and bio-char were successfully characterized using Elemental analysis, Chemical composition, TGA, FTIR, 1 H NMR, GC-MS and SEM. At a temperature of 500°C and a heating rate of 10°C/min, the maximum yield of bio-oil and bio-char was found to be 24.10 and 44.01wt%, respectively, which was found to be strongly influenced by the temperature variation, and weakly affected by the heating rate variation. Results show that the bio-oil cannot be used as bio-fuel, but can be used as a source of value-added chemicals. On the other hand, the bio-char is a promising candidate for solid fuel applications and for the production of carbon materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

Simulation of fluidized bed coal combustors

NASA Technical Reports Server (NTRS)

Rajan, R.

1979-01-01

The many deficiencies of previous work on simulation of fluidized bed combustion (FBC) processes are presented. An attempt is made to reduce these deficiencies, and to formulate a comprehensive FBC model taking into account the following elements: (1) devolatilization of coal and the subsequent combustion of volatiles and residual char; (2) sulfur dioxide capture by limestone; (3) NOx release and reduction of NOx by char; (4) attrition and elutriation of char and limestone; (5) bubble hydrodynamics; (6) solids mixing; (7) heat transfer between gas and solid, and solid and heat exchange surfaces; and (8) freeboard reactions.

Production of MHD fluid

DOEpatents

Lacey, James J.; Kurtzrock, Roy C.; Bienstock, Daniel

1976-08-24

A hot gaseous fluid of low ash content, suitable for use in open-cycle MHD (magnetohydrodynamic) power generation, is produced by means of a three-stage process comprising (1) partial combustion of a fossil fuel to produce a hot gaseous product comprising CO.sub.2 CO, and H.sub.2 O, (2) reformation of the gaseous product from stage (1) by means of a fluidized char bed, whereby CO.sub.2 and H.sub.2 O are converted to CO and H.sub.2, and (3) combustion of CO and H.sub.2 from stage (2) to produce a low ash-content fluid (flue gas) comprising CO.sub.2 and H.sub.2 O and having a temperature of about 4000.degree. to 5000.degree.F.

Chemoselective methylation of phenolic hydroxyl group prevents quinone methide formation and repolymerization during lignin depolymerization

DOE PAGES

Kim, Kwang Ho; Dutta, Tanmoy; Walter, Eric D.; ...

2017-03-22

Chemoselective blocking of the phenolic hydroxyl (Ar–OH) group by methylation was found to suppress secondary repolymerization and charring during lignin depolymerization. Methylation of Ar–OH prevents formation of reactive quinone methide intermediates, which are partly responsible for undesirable secondary repolymerization reactions. Instead, this structurally modified lignin produces more relatively low molecular weight products from lignin depolymerization compared to unmodified lignin. This result demonstrates that structural modification of lignin is desirable for production of low molecular weight phenolic products. Finally, this approach could be directed toward alteration of natural lignification processes to produce biomass that is more amenable to chemical depolymerization.

Fıxed bed slow pyrolysıs of bıomass solıd waste for bıo-char

NASA Astrophysics Data System (ADS)

Islam, M. N.; Ali, M. H.; Ahmad, I.

2017-06-01

Biomass solid waste in the form of rice husk particle is pyrolyzed in a fixed bed pyrolysis reactor. The reactor is made of stainless steel with dimensions of 76 mm in diameter and 90 cm in length. Rice husk is collected locally from Brunei-Muara district of Brunei Darussalam which is processed for pyrolysis. The particles are selected in the millimeter range. It is oven-dried at 105°C for 6 hours after being air-dried prior to pyrolysis. The reactor bed is heated by means of saw-dust in a biomass source heater. A temperature range of 390-410°C is maintained with an apperent vapor residence time of 30 min. Nitrogen gas is passed through the reactor system to make the atmosphere inert. A water-cooled condenser is used to derive bio-oil from the condensable vapors. The system is subjected to pyrolysis for a running time of 60 min. The products obtained are solid bio-char, liquid bio-oil and pyrolytic bio-gases. The solid char yield is found to be 45 by weight of solid biomass feedstock and the liquid product yield is found to be 29 by weight of solid biomass feedstock. The rest is gas flared into the atmosphere. The bio-char is retained in the reactor and collected at the end of the experimental run. The bio-char is found to be black in color retaining its original shape. The bio-char product is subjected to energy analysis for its higher heating value (HHV) by means of an oxygen bomb calorimeter. It is found to be 20.3 MJ/kg. The density of the bio-char is found to be 238.5 kg/m3 with an energy density of 4.85 GJ/m3.

Co-pyrolysis behaviour and kinetic of two typical solid wastes in China and characterisation of activated carbon prepared from pyrolytic char.

PubMed

Ma, Yuhui; Niu, Ruxuan; Wang, Xiaona; Wang, Qunhui; Wang, Xiaoqiang; Sun, Xiaohong

2014-11-01

This is the first study on the co-pyrolysis of spent substrate of Pleurotus ostreatus and coal tar pitch, and the activated carbon prepared from the pyrolytic char. Thermogravimetry (TG) analysis was carried out taking spent substrate, coal tar pitch and spent substrate-coal tar pitch mixture. The activation energies of pyrolysis reactions were obtained via the Flynn-Wall-Ozawa and Kissinger-Akahira-Sunose methods. The kinetic models were determined by the master-plots method. The activated carbons were characterised by N2-adsorption, Fourier transform infrared spectroscopy and X-ray diffraction. Experimental results demonstrated a synergistic effect happened during co-pyrolysis, which was characterised by a decreased maximum decomposition rate and an enhanced char yield. The average activation energies of the pyrolysis reactions of spent substrate, coal tar pitch and the mixture were 115.94, 72.92 and 94.38 kJ mol(-1) for the Flynn-Wall-Ozawa method, and 112.17, 65.62 and 89.91 kJ mol(-1) for the Kissinger-Akahira-Sunose method. The reaction model functions were f(α) = (1-α)(3.42), (1-α)(1.72) and (1-α)(3.07) for spent substrate, coal tar pitch and the mixture, respectively. The mixture char-derived activated carbon had a Brunauer-Emmett-Teller surface area up to 1337 m(2) g(-1) and a total pore volume of 0.680 cm(3) g(-1). Mixing spent substrate with coal tar pitch led to the creation of more micropores and a higher surface area compared with the single spent substrate and coal tar pitch char. Also, the mixture char-derived activated carbon had a higher proportion of aromatic stacking. This study provides a reference for the utilisation of spent substrate and coal tar pitch via co-pyrolysis, and their pyrolytic char as a promising precursor of activated carbon. © The Author(s) 2014.

Charring temperatures are driven by the fuel types burned in a peatland wildfire

PubMed Central

Hudspith, Victoria A.; Belcher, Claire M.; Yearsley, Jonathan M.

2014-01-01

Peatlands represent a globally important carbon store; however, the human exploitation of this ecosystem is increasing both the frequency and severity of fires on drained peatlands. Yet, the interactions between the hydrological conditions (ecotopes), the fuel types being burned, the burn severity, and the charring temperatures (pyrolysis intensity) remain poorly understood. Here we present a post-burn assessment of a fire on a lowland raised bog in Co. Offaly, Ireland (All Saints Bog). Three burn severities were identified in the field (light, moderate, and deeply burned), and surface charcoals were taken from 17 sites across all burn severities. Charcoals were classified into two fuel type categories (either ground or aboveground fuel) and the reflectance of each charcoal particle was measured under oil using reflectance microscopy. Charcoal reflectance shows a positive relationship with charring temperature and as such can be used as a temperature proxy to reconstruct minimum charring temperatures after a fire event. Resulting median reflectance values for ground fuels are 1.09 ± 0.32%Romedian, corresponding to estimated minimum charring temperatures of 447°C ± 49°C. In contrast, the median charring temperatures of aboveground fuels were found to be considerably higher, 646°C ± 73°C (3.58 ± 0.77%Romedian). A mixed-effects modeling approach was used to demonstrate that the interaction effects of burn severity, as well as ecotope classes, on the charcoal reflectance is small compared to the main effect of fuel type. Our findings reveal that the different fuel types on raised bogs are capable of charring at different temperatures within the same fire, and that the pyrolysis intensity of the fire on All Saints Bog was primarily driven by the fuel types burning, with only a weak association to the burn severity or ecotope classes. PMID:25566288

Biomass waste gasification - can be the two stage process suitable for tar reduction and power generation?

PubMed

Sulc, Jindřich; Stojdl, Jiří; Richter, Miroslav; Popelka, Jan; Svoboda, Karel; Smetana, Jiří; Vacek, Jiří; Skoblja, Siarhei; Buryan, Petr

2012-04-01

A pilot scale gasification unit with novel co-current, updraft arrangement in the first stage and counter-current downdraft in the second stage was developed and exploited for studying effects of two stage gasification in comparison with one stage gasification of biomass (wood pellets) on fuel gas composition and attainable gas purity. Significant producer gas parameters (gas composition, heating value, content of tar compounds, content of inorganic gas impurities) were compared for the two stage and the one stage method of the gasification arrangement with only the upward moving bed (co-current updraft). The main novel features of the gasifier conception include grate-less reactor, upward moving bed of biomass particles (e.g. pellets) by means of a screw elevator with changeable rotational speed and gradual expanding diameter of the cylindrical reactor in the part above the upper end of the screw. The gasifier concept and arrangement are considered convenient for thermal power range 100-350 kW(th). The second stage of the gasifier served mainly for tar compounds destruction/reforming by increased temperature (around 950°C) and for gasification reaction of the fuel gas with char. The second stage used additional combustion of the fuel gas by preheated secondary air for attaining higher temperature and faster gasification of the remaining char from the first stage. The measurements of gas composition and tar compound contents confirmed superiority of the two stage gasification system, drastic decrease of aromatic compounds with two and higher number of benzene rings by 1-2 orders. On the other hand the two stage gasification (with overall ER=0.71) led to substantial reduction of gas heating value (LHV=3.15 MJ/Nm(3)), elevation of gas volume and increase of nitrogen content in fuel gas. The increased temperature (>950°C) at the entrance to the char bed caused also substantial decrease of ammonia content in fuel gas. The char with higher content of ash leaving the second stage presented only few mass% of the inlet biomass stream. Copyright © 2011 Elsevier Ltd. All rights reserved.

Reactivity of young chars via energetic distribution measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calo, J.M.; Lilly, W.D.

1991-01-01

The current project is directed at developing related techniques for the characterization and prediction/correlation of the reactivity of young'' chars to steam and oxygen. Of particular interest is mapping of the reactivity behavior of the resultant chars, as revealed by the energetic heterogeneity of the complexes with char preparation conditions; i.e., heating rate and ultimate temperature. In this first quarterly technical progress report we present the background of the project and the research program for the proposed investigations. The following work was accomplished on the experimental apparatus: a new set of electronics for the UTi quadrupole mass spectrometer head wasmore » purchased and delivered. The Temperature Programmed Desorption (TPD) System was moved to another laboratory and interfaced with the mass spectrometer system. A Polycold{trademark} freon refrigeration system was repaired and interfaced with the vacuum system for the TPD apparatus. It will be used to cool the diffusion pump trap. 60 refs.« less

Porous carbon from local coconut shell char by CO2 and H2O activation in the presence of K2CO3

NASA Astrophysics Data System (ADS)

Vi, Nguyen Ngoc Thuy; Truyen, Dang Hai; Trung, Bien Cong; An, Ngo Thanh; Van Dung, Nguyen; Long, Nguyen Quang

2017-09-01

Vietnamese coconut shell char was activated by steam and carbon dioxide at low temperatures with the presence of K2CO3 as a catalyst. The effects of process parameters on adsorption capability of the product including different ratio of impregnation of activation agents, activation temperature, activation time were investigated in this study. Iodine number, methylene blue adsorption capacity, specific surface area and pore size distribution were measured to assess the properties of the activated carbon. Accordingly, the porous carbon was applied for toluene removal by adsorption technology. Significant increases in specific surface area and the toluene adsorption capacity were observed when the coconut shell char was activated in CO2 flow at 720 °C for 150 minutes and the K2CO3/char weight ratio of 0.5.

Burning rate of solid wood measured in a heat release rate calorimeter

Treesearch

H. C. Tran; R. H. White

1992-01-01

Burning rate is a key factor in modeling fire growth and fire endurance of wood structures. This study investigated the burning rate of selected wood materials as determined by heat release, mass loss and charring rates. Thick samples of redwood, southern pine, red oak and basswood were tested in a heat release rate calorimeter. Results on ignitability and average beat...

Role of structure, accessibility and microporosity on sorption of phenanthrene and nonylphenol by sediments and their fractions.

PubMed

Zhang, Dainan; Duan, Dandan; Huang, Youda; Xiong, Yongqiang; Yang, Yu; Ran, Yong

2016-12-01

To better understand interaction mechanism of sediment organic matter with hydrophobic organic compounds, sorption of phenanthrene (Phen) and nonylphenol (NP) by bulk sediments and their fractions was investigated. Three surface sediments were selectively fractionated into different organic fractions, including the demineralized carbon (DM), lipid free carbon (LF), lipid (LP), and nonhydrolyzable carbon (NHC) fractions. The structure and microporosity of the isolated fractions were characterized by NMR and CO 2 adsorption techniques, and used as sorbents for Phen and NP. The calculated micropore volumes (V o ) and specific surface area (SSA) values are positively related to the concentrations of aromatic C and char for the DM, LF and NHC fractions, suggesting that aromatic moieties and char component significantly contribute to the microporosity. The LF fractions exhibit greater sorption affinity than the DM fractions do, indicating that the presence of LP could block the accessibility of sorption sites for Phen and NP. Significant and positive correlations among log K' FOC values for Phen and NP and aromatic carbon and char contents, and V o and SSA values suggest the aromatic moieties and microporosity dominate their sorption of HOCs by sediment organic matter (SOM). As the NHC fractions have much stronger sorption than other fractions do, they dominate the overall sorption by the bulk samples. This study indicated that the important roles of aromatic moieties, accessibility, and microporosity in the sorption of HOCs by SOM. Copyright © 2016 Elsevier Ltd. All rights reserved.

Critical analysis of pyrolysis process with cellulosic based municipal waste as renewable source in energy and technical perspective.

PubMed

Agarwal, Manu; Tardio, James; Venkata Mohan, S

2013-11-01

To understand the potential of cellulosic based municipal waste as a renewable feed-stock, application of pyrolysis by biorefinery approach was comprehensively studied for its practicable application towards technical and environmental viability in Indian context. In India, where the energy requirements are high, the pyrolysis of the cellulosic waste shows numerous advantages for its applicability as a potential waste-to-energy technology. The multiple energy outputs of the process viz., bio-gas, bio-oil and bio-char can serve the two major energy sectors, viz., electricity and transportation. The process suits best for high bio-gas and electrical energy production when energy input is satisfied from bio-char in form of steam (scheme-1). The bio-gas generated through the process shows its direct utility as a transportation fuel while the bio-oil produced can serve as fuel or raw material to chemical synthesis. On a commercial scale the process is a potent technology towards sustainable development. The process is self-sustained when operated on a continuous mode. Copyright © 2013 Elsevier Ltd. All rights reserved.

Highly porous activated carbons from resource-recovered Leucaena leucocephala wood as capacitive deionization electrodes.

PubMed

Hou, Chia-Hung; Liu, Nei-Ling; Hsi, Hsing-Cheng

2015-12-01

Highly porous activated carbons were resource-recovered from Leucaena leucocephala (Lam.) de Wit. wood through combined chemical and physical activation (i.e., KOH etching followed by CO2 activation). This invasive species, which has severely damaged the ecological economics of Taiwan, was used as the precursor for producing high-quality carbonaceous electrodes for capacitive deionization (CDI). Carbonization and activation conditions strongly influenced the structure of chars and activated carbons. The total surface area and pore volume of activated carbons increased with increasing KOH/char ratio and activation time. Overgasification induced a substantial amount of mesopores in the activated carbons. In addition, the electrochemical properties and CDI electrosorptive performance of the activated carbons were evaluated; cyclic voltammetry and galvanostatic charge/discharge measurements revealed a typical capacitive behavior and electrical double layer formation, confirming ion electrosorption in the porous structure. The activated-carbon electrode, which possessed high surface area and both mesopores and micropores, exhibited improved capacitor characteristics and high electrosorptive performance. Highly porous activated carbons derived from waste L. leucocephala were demonstrated to be suitable CDI electrode materials. Copyright © 2015 Elsevier Ltd. All rights reserved.

Peroxide-assisted microwave activation of pyrolysis char for adsorption of dyes from wastewater.

PubMed

Nair, Vaishakh; Vinu, R

2016-09-01

In this study, mesoporous activated biochar with high surface area and controlled pore size was prepared from char obtained as a by-product of pyrolysis of Prosopis juliflora biomass. The activation was carried out by a simple process that involved H2O2 treatment followed by microwave pyrolysis. H2O2 impregnation time and microwave power were optimized to obtain biochar with high specific surface area and high adsorption capacity for commercial dyes such as Remazol Brilliant Blue and Methylene Blue. Adsorption parameters such as initial pH of the dye solution and adsorbent dosage were also optimized. Pore size distribution, surface morphology and elemental composition of activated biochar were thoroughly characterized. H2O2 impregnation time of 24h and microwave power of 600W produced nanostructured biochar with narrow and deep pores of 357m(2)g(-1) specific surface area. Langmuir and Langmuir-Freundlich isotherms described the adsorption equilibrium, while pseudo second order model described the kinetics of adsorption. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pyrolysis of oil palm mesocarp fiber and palm frond in a slow-heating fixed-bed reactor: A comparative study.

PubMed

Kabir, G; Mohd Din, A T; Hameed, B H

2017-10-01

Oil palm mesocarp fiber (OPMF) and palm frond (PF) were respectively devolatilized by pyrolysis to OPMF-oil and PF-oil bio-oils and biochars, OPMF-char and PF-char in a slow-heating fixed-bed reactor. In particular, the OPMF-oil and PF-oil were produced to a maximum yield of 48wt% and 47wt% bio-oils at 550°C and 600°C, respectively. The high heating values (HHVs) of OPMF-oil and PF-oil were respectively found to be 23MJ/kg and 21MJ/kg, whereas 24.84MJ/kg and 24.15MJ/kg were for the corresponding biochar. The HHVs of the bio-oils and biochars are associated with low O/C ratios to be higher than those of the corresponding biomass. The Fourier transform infrared spectra and peak area ratios highlighted the effect of pyrolysis temperatures on the bio-oil compositions. The bio-oils are pervaded with numerous oxygenated carbonyl and aromatic compounds as suitable feedstocks for renewable fuels and chemicals. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparison of pyrolytic products produced from inorganic-rich and demineralized rice straw (Oryza sativa L.) by fluidized bed pyrolyzer for future biorefinery approach.

PubMed

Eom, In-Yong; Kim, Jae-Young; Lee, Soo-Min; Cho, Tae-Su; Yeo, Hwanmyeong; Choi, Joon-Weon

2013-01-01

The objectives of this study were to investigate the effects of inorganic constituents on the fast pyrolysis of the biomass and to determine the yields as well as physicochemical properties of pyrolytic products. The pyrolytic products were obtained from raw and demineralized rice straw using a fluidized bed type pyrolyzer at different temperatures. As pyrolysis temperature increased, total biooil yield gradually decreased from 46.6 to 29.6 wt.% for the raw-straw, and from 55.4 to 35.3 wt.% for the demineralized rice straw. For demineralized rice straw, higher pyrolysis temperatures promoted gasification reactions but reduced char formations. However, char yield for the raw-straw was relatively unaffected by temperature due to an increase in carbonization reactions that were catalyzed by some inorganics. Certain inorganic constituents in the biomass were distinctively distributed in the biooil, and ICP-ES and GC/MS analysis indicated that some inorganics may be chemically bound to cell wall components. Copyright © 2012 Elsevier Ltd. All rights reserved.

Functionalized carbon dot adorned coconut shell char derived green catalysts for the rapid synthesis of amidoalkyl naphthols.

PubMed

Narayanan, Divya P; Cherikallinmel, Sudha Kochiyil; Sankaran, Sugunan; Narayanan, Binitha N

2018-06-15

A one pot synthesis of carbon dot incorporated porous coconut shell char derived sulphonated catalyst is reported here for the first time and is effectively used in the multicomponent synthesis of amidoalkyl naphthol. Macroporous nature of the char is revealed from scanning electron microscopic (SEM) analysis, whereas the dispersion of carbon dots (CDs) on the porous coconut shell char is confirmed from the high resolution transmission electron microscopic (HRTEM) analysis. Fluorescence emission spectrum further confirmed the presence of CDs in the catalyst. Fourier-transform infrared (FTIR) spectral analysis of the materials indicated that sulphonation occurred both to the CD and to the porous char. X-ray photo electron spectroscopic (XPS) analysis of the most active catalyst confirmed the presence of both sulphonic acid and carboxylic acid groups in the catalyst. The coconut shell char derived materials prepared by varying the amount of H 2 SO 4 are successfully utilized as efficient alternative green catalysts for the multicomponent reaction, where excellent activity in amidoalkyl naphthol synthesis is obtained within short periods under solvent free reaction conditions. A maximum yield of 98% is obtained in the synthesis of N-[Phenyl-(2-hydroxy-naphthalen-1-yl)-methyl]-benzamide, the representative amidoalkyl naphthol, with the best catalyst within 3 min of reaction. The catalyst is highly active for the reactions carried out with varieties of aldehydes and amides with a product yield in the range of 88-98%. The best catalyst system retained more than 90% of its initial activity even upto 6 th repeated run. Copyright © 2018 Elsevier Inc. All rights reserved.

Nitric oxide reduction in coal combustion: role of char surface complexes in heterogeneous reactions.

PubMed

Arenillas, Ana; Rubiera, Fernando; Pis, José J

2002-12-15

Nitrogen oxides are one of the major environmental problems arising from fossil fuel combustion. Coal char is relatively rich in nitrogen, and so this is an important source of nitrogen oxides during coal combustion. However, due to its carbonaceous nature, char can also reduce NO through heterogeneous reduction. The objectives of this work were on one hand to compare NO emissions from coal combustion in two different types of equipment and on the other hand to study the influence of char surface chemistry on NO reduction. A series of combustion tests were carried out in two different scale devices: a thermogravimetric analyzer coupled to a mass spectrometer and an FTIR (TG-MS-FTIR) and a fluidized bed reactor with an on line battery of analyzers. The TG-MS-FTIR system was also used to perform a specific study on NO heterogeneous reduction reactions using chars with different surface chemistry. According to the results obtained, it can be said that the TG-MS-FTIR system provides valuable information about NO heterogeneous reduction and it can give good trends of the behavior in other combustion equipments (i.e., fluidized bed combustors). It has been also pointed out that NO-char interaction depends to a large extent on temperature. In the low-temperature range (<800 degrees C), NO heterogeneous reduction seems to be controlled by the evolution of surface complexes. In the high-temperature range (>800 degrees C), a different mechanism is involved in NO heterogeneous reduction, the nature of the carbon matrix being a key factor.

Thermal/optical methods for elemental carbon quantification in soils and urban dusts: equivalence of different analysis protocols.

PubMed

Han, Yongming; Chen, Antony; Cao, Junji; Fung, Kochy; Ho, Fai; Yan, Beizhan; Zhan, Changlin; Liu, Suixin; Wei, Chong; An, Zhisheng

2013-01-01

Quantifying elemental carbon (EC) content in geological samples is challenging due to interferences of crustal, salt, and organic material. Thermal/optical analysis, combined with acid pretreatment, represents a feasible approach. However, the consistency of various thermal/optical analysis protocols for this type of samples has never been examined. In this study, urban street dust and soil samples from Baoji, China were pretreated with acids and analyzed with four thermal/optical protocols to investigate how analytical conditions and optical correction affect EC measurement. The EC values measured with reflectance correction (ECR) were found always higher and less sensitive to temperature program than the EC values measured with transmittance correction (ECT). A high-temperature method with extended heating times (STN120) showed the highest ECT/ECR ratio (0.86) while a low-temperature protocol (IMPROVE-550), with heating time adjusted for sample loading, showed the lowest (0.53). STN ECT was higher than IMPROVE ECT, in contrast to results from aerosol samples. A higher peak inert-mode temperature and extended heating times can elevate ECT/ECR ratios for pretreated geological samples by promoting pyrolyzed organic carbon (PyOC) removal over EC under trace levels of oxygen. Considering that PyOC within filter increases ECR while decreases ECT from the actual EC levels, simultaneous ECR and ECT measurements would constrain the range of EC loading and provide information on method performance. Further testing with standard reference materials of common environmental matrices supports the findings. Char and soot fractions of EC can be further separated using the IMPROVE protocol. The char/soot ratio was lower in street dusts (2.2 on average) than in soils (5.2 on average), most likely reflecting motor vehicle emissions. The soot concentrations agreed with EC from CTO-375, a pure thermal method.

Analysis of black carbon molecular markers by two chromatographic methods (GC-FID and HPLC-DAD)

NASA Astrophysics Data System (ADS)

Schneider, Maximilian P. W.; Smittenberg, Rienk H.; Dittmar, Thorsten; Schmidt, Michael W. I.

2010-05-01

The analysis of benzenepolycarboxylic acids (BPCA) as a quantitative measure for black carbon (BC) in soil and sediment samples is a well-established method [1, 2]. Briefly, the oxidation of polycondensated BC molecules forms seven molecular markers, which can be assigned to BC, and which subsequently can be quantified by GC-FID (gas chromatography with flame ionization detector). Recently this method has been refined for BC quantification in seawater samples measuring BPCA on HPLC-DAD (High performance liquid chromatography with diode array detector) [3]. However, a systematic comparison of BC as determined by both analytical techniques would be essential to the calculation of global BC budgets, but is lacking. Here we present data for the systematic comparison of the two BPCA methods, both for quantity and quality. We prepared chars under well-defined laboratory conditions. Chestnut hardwood chips and rice straw were pyrolysed at temperatures between 200 and 1000°C under constant N2 stream. The BC contents of the chars have been analysed using the BPCA extraction method followed by either GC-FID or HPLC-DAD quantification [4]. It appears that the GC-FID method yields systematically lower concentrations of BPCA in the chars compared to the HPLC-DAD method. Possible reasons for the observed difference are i) higher losses of sample material during preparation for GC-FID; ii) different quality of the linear regression used for quantification; iii) incomplete derivatisation of B5CA and B6CA, which is needed for GC-FID analysis. In a next step, we will test different derivatisation procedures (methylation with dimethyl sulfate or diazomethane, and silylation) for their influence on the GC-FID results. The aim of this study is to test if black carbon can be quantified in soil, sediment and water samples using one single method - a crucial step when attempting a global BC budget. References: [1] Brodowski, S., Rodionov, A., Haumeier L., Glaser, B., Amelung, W. (2005) Org. Geochem. 36, 1299-1310. [2] Glaser, B., Haumeier, L., Guggenberger, G., Zech, W. (1998) Org. Geochem. 29, 811-819. [3] Dittmar, T. (2008) Org. Geochem. 39. 396-407. [4] Schneider, M.P.W., Hilf, M., Vogt, U.F., Schmidt, M.W.I., Org. Geochem. (submitted)

Combustion behavior of different kinds of torrefied biomass and their blends with lignite.

PubMed

Toptas, Asli; Yildirim, Yeliz; Duman, Gozde; Yanik, Jale

2015-02-01

In this study, the combustion behavior of different kinds of torrefied biomass (lignocellulosic and animal wastes) and their blends with lignite was investigated via non-isothermal thermogravimetric method under air atmosphere. For comparison, combustion characteristics of raw biomasses were also determined. Torrefaction process improved the reactivity of char combustion step of biomasses. Characteristic combustion parameters for blends showed non-additivity behavior. It was found that the mixture of torrefied biomasses and lignite at a ratio of 1:1 had a lower ignition and burnout temperature than the coal-only sample. Although no interactions were observed between the lignite and torrefied biomass at initial step of combustion, a certain degree of interaction between the components occurred at char combustion step. Kinetic parameters of combustion were calculated by using the Coats Redfern model. Overall, this study showed that poultry litters can be used as a substitute fuel in coal/biomass co-firing systems by blending with lignocellulosic biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

George W. Huber; Upadhye, Aniruddha A.; Ford, David M.

This University of Massachusetts, Amherst project, "Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils" started on 1st February 2009 and finished on August 31st 2011. The project consisted following tasks: Task 1.0: Char Removal by Membrane Separation Technology The presence of char particles in the bio-oil causes problems in storage and end-use. Currently there is no well-established technology to remove char particles less than 10 micron in size. This study focused on the application of a liquid-phase microfiltration process to remove char particles from bio-oil down to slightly sub-micron levels. Tubular ceramic membranes of nominalmore » pore sizes 0.5 and 0.8m were employed to carry out the microfiltration, which was conducted in the cross-flow mode at temperatures ranging from 38 to 45 C and at three different trans-membrane pressures varying from 1 to 3 bars. The results demonstrated the removal of the major quantity of char particles with a significant reduction in overall ash content of the bio-oil. The results clearly showed that the cake formation mechanism of fouling is predominant in this process. Task 2.0 Acid Removal by Membrane Separation Technology The feasibility of removing small organic acids from the aqueous fraction of fast pyrolysis bio-oils using nanofiltration (NF) and reverse osmosis (RO) membranes was studied. Experiments were carried out with a single solute solutions of acetic acid and glucose, binary solute solutions containing both acetic acid and glucose, and a model aqueous fraction of bio-oil (AFBO). Retention factors above 90% for glucose and below 0% for acetic acid were observed at feed pressures near 40 bar for single and binary solutions, so that their separation in the model AFBO was expected to be feasible. However, all of the membranes were irreversibly damaged when experiments were conducted with the model AFBO due to the presence of guaiacol in the feed solution. Experiments with model AFBO excluding guaiacol were also conducted. NF membranes showed retention factors of glucose greater than 80% and of acetic acid less than 15% when operated at transmembrane pressures near 60 bar. Task 3.0 Acid Removal by Catalytic Processing It was found that the TAN reduction in bio-oil was very difficult using low temperature hydrogenation in flow and batch reactors. Acetic acid is very resilient to hydrogenation and we could only achieve about 16% conversion for acetic acid. Although it was observed that acetic acid was not responsible for instability of aqueous fraction of bio-oil during ageing studies (described in task 5). The bimetallic catalyst PtRe/ceria-zirconia was found to be best catalyst because its ability to convert the acid functionality with low conversion to gas phase carbon. Hydrogenation of the whole bio-oil was carried out at 125°C, 1450 psi over Ru/C catalyst in a flow reactor. Again, negligible acetic acid conversion was obtained in low temperature hydrogenation. Hydrogenation experiments with whole bio-oil were difficult to perform because of difficulty to pumping the high viscosity oil and reactor clogging. Task 4.0 Acid Removal using Ion Exchange Resins DOWEX M43 resin was used to carry out the neutralization of bio-oil using a packed bed column. The pH of the bio-oil increased from 2.43 to 3.7. The GC analysis of the samples showed that acetic acid was removed from the bio-oil during the neutralization and recovered in the methanol washing. But it was concluded that process would not be economical at large scale as it is extremely difficult to regenerate the resin once the bio-oil is passed over it. Task 5.0 Characterization of Upgraded Bio-oils We investigated the viscosity, microstructure, and chemical composition of bio-oils prepared by a fast pyrolysis approach, upon aging these fuels at 90ºC for periods of several days. Our results suggest that the viscosity increase is not correlated with the acids or char present in the bio-oils. The viscosity increase is due to formation of high molecular weight polymeric species over time. Our work also suggests that hydrogenation of the samples is beneficial in eliminating the viscosity increase. Task 6.0 Commercialization Assessment Renewable Oil International LLC (ROI) was responsible for Task 6.0, Commercialization Assessment. As part of this effort ROI focused on methods to reduce char carryover in the vapor stream from the fast pyrolysis reactor and residence time of the vapor in the reactor. Changes were made in the bio-oil recovery methodology and a reactor sweep gas used to reduce vapor residence time. Cyclones were placed in the vapor stream to reduce char particulate carryover. Microfiltration of the bio-oil was also researched to remove char particulate from the bio-oil. The capital cost for these improvements would be less than 2% of the total plant capital cost.« less

Char from sugarcane bagasse

USDA-ARS?s Scientific Manuscript database

Unused sugarcane bagasse represents an underutilized resource in sugarcane growing regions of the world. This is a renewable resource that can be used in a thermochemical process to create chars, which could be incorporated back into agricultural activities. The practice is likely to improve soil ...

Recovery of a Charred Painting Using Atomic Oxygen Treatment

NASA Technical Reports Server (NTRS)

Rutledge, Sharon K.; Banks, Bruce A.; Chichernea, Virgil A.

1999-01-01

A noncontact method is described which uses atomic oxygen to remove soot and char from the surface of a painting. The atomic oxygen was generated by the dissociation of oxygen in low pressure air using radio frequency energy. The treatment, which is an oxidation process, allows control of the amount of material to be removed. The effectiveness of char removal from half of a fire-damaged oil painting was studied using reflected light measurements from selected areas of the painting and by visual and photographic observation. The atomic oxygen was able to effectively remove char and soot from the treated half of the painting. The remaining loosely bound pigment was lightly sprayed with a mist to replace the binder and then varnish was reapplied. Caution should he used when treating an untested paint medium using atomic oxygen. A representative edge or corner should he tested first in order to determine if the process would be safe for the pigments present. As more testing occurs, a greater knowledge base will be developed as to what types of paints and varnishes can or cannot be treated using this technique. With the proper precautions, atomic oxygen treatment does appear to be a technique with great potential for allowing very charred, previously unrestorable art to be salvaged.

Production and characterization of chars from cherry pulp via pyrolysis.

PubMed

Pehlivan, E; Özbay, N; Yargıç, A S; Şahin, R Z

2017-12-01

Pyrolysis is an eco-friendly process to achieve valuable products like bio-oil, char and gases. In the last decades, biochar production from pyrolysis of a wide variety of industrial and agricultural wastes become popular, which can be utilized as adsorbent instead of the expensive activated carbons. In this study, cherry pulp was pyrolyzed in a fixed bed tubular reactor at five different temperatures (400, 500,550, 600 and 700 °C) and three different heating rates (10, 100 and 200 °C/min) to obtain biochar. Proximate, ultimate, nitrogen adsorption/desorption isotherms, scanning electron microscopy, thermogravimetric analysis, x-ray fluorescence, x-ray diffraction, and Fourier transform infrared spectroscopy were performed on cherry pulp and its chars to examine the chemical alterations after the pyrolysis process. Biochar yields were decreased with increasing pyrolysis temperature and heating rate, based on experimental results. Porous biochars are carbon rich and includes high potassium content. The aromaticity of biochars increased and O/C mass ratio reduced with an increase in the pyrolysis temperature as a result of the development of compact aromatic structure in char. Pyrolysis provides a promising conversion procedure for the production of high energy density char which has promising applications in existing coal-fired boilers without any upgrading. Copyright © 2017 Elsevier Ltd. All rights reserved.

Role of charred wood, heat-shock and light in germination of postfire phrygana species from the eastern Mediterranean Basin

USGS Publications Warehouse

Keeley, Jon E.; Babr-Keeley, Melanie

1999-01-01

Seeds of 22 species collected from recently burned phrygana were tested for their response to fire-type cues of charred wood and heat-shock. All Cistus species were stimulated by brief heat-shock, as shown in previous studies; however, none responded to charred wood. Only one of the 22 species was stimulated by charred wood, and only in dark-inhibited seeds, and this response did not occur in the light. The lack of charred-wood-induced germination is in contrast to the substantial proportion of species with this germination response reported for mediterranean-type vegetation in California, the Cape region of South Africa, and Western Australia. Phrygana has many species with heat-shock-stimulated germination, primarily in the Fabaceae and Cistaceae. This germination cue is widespread in these two families, thus, the presence of heat-shock-stimulated germination is a result of homologous, rather than covergent, adaptations in mediterranean-climate ecosystems. Germination response to light was not randomly distributed with respect to fire-type response. Heat-shock-stimulated species were almost uniformly light neutral, in contrast to more opportunistic colonizing species with non-refractory seeds, in which half of the species responded positively or negatively to light.

Successful implementation of biochar carbon sequestration in European soils requires additional benefits and close collaboration with the bioenergy sector

NASA Astrophysics Data System (ADS)

Hauggaard-Nielsen, Henrik; Müller-Stöver, Dorette; Bruun, Esben W.; Petersen, Carsten T.

2014-05-01

Biochar soil application has been proposed as a measure to mitigate climate change and on the same time improve soil fertility by increased soil carbon sequestration. However, while on tropical soils the beneficial effects of biochar application on crop growth often become immediately apparent, it has been shown to be more difficult to demonstrate these effects on the more fertile soils in temperate regions. Therefore and because of the lack of carbon credits for farmers, it is necessary to link biochar application to additional benefits, both related to agricultural as well as to bioenergy production. Thermal gasification of biomass is an efficient (95% energy efficiency) and flexible way (able to cope with many different and otherwise difficult-to-handle biomass fuels) to generate bioenergy, while producing a valuable by-product - gasification biochar, containing recalcitrant carbon and essential crop nutrients. The use of the residual char product in agricultural soils will add value to the technology as well as result in additional soil benefits such as providing plant nutrients and improving soil water-holding capacity while reducing leaching risks. From a soil column (30 x 130 cm) experiment with gasification straw biochar amendment to coarse sandy subsoil increased root density of barley at critical depths in the soil profile reducing the mechanical resistance was shown, increasing yields, and the soil's capacity to store plant available water. Incorporation of residuals from a bioenergy technology like gasification show great potentials to reduce subsoil constraints increasing yield potentials on poor soils. Another advantage currently not appropriately utilized is recovery of phosphorus (P). In a recent pot experiments char products originating from low-temperature gasification of various biofuels were evaluated for their suitability as P fertilizers. Wheat straw gasification biochar generally had a low P content but a high P plant availability. To improve the fertilizer value while keeping a high carbon content in the char, the gasification of a combination of sewage sludge and wheat straw was implemented, resulting in a char product with a promising performance as a fertilizer and soil amendment. To implement gasification-biochar as a promising soil improver on the marked, independently of potential carbon market developments and CO2 certificates, stakeholder involvement is strongly required. In a newly established project consortium Bregentved Estate (one of Europe's largest agriculture companies) and the DONG Energy company (one of the leading energy groups in Northern Europe) are in a joint effort trying to integrate the economic matrix of i) biomass needed for bioenergy, ii) profit from energy generation and iii) soil advantages gained from biochar application. Experiments are conducted with a 6MW biomass gasification demonstration plant producing straw biochar used in field plots (12 m x 250 m).

Biomass waste gasification - Can be the two stage process suitable for tar reduction and power generation?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sulc, Jindrich; Stojdl, Jiri; Richter, Miroslav

2012-04-15

Highlights: Black-Right-Pointing-Pointer Comparison of one stage (co-current) and two stage gasification of wood pellets. Black-Right-Pointing-Pointer Original arrangement with grate-less reactor and upward moving bed of the pellets. Black-Right-Pointing-Pointer Two stage gasification leads to drastic reduction of tar content in gas. Black-Right-Pointing-Pointer One stage gasification produces gas with higher LHV at lower overall ER. Black-Right-Pointing-Pointer Content of ammonia in gas is lower in two stage moving bed gasification. - Abstract: A pilot scale gasification unit with novel co-current, updraft arrangement in the first stage and counter-current downdraft in the second stage was developed and exploited for studying effects of two stagemore » gasification in comparison with one stage gasification of biomass (wood pellets) on fuel gas composition and attainable gas purity. Significant producer gas parameters (gas composition, heating value, content of tar compounds, content of inorganic gas impurities) were compared for the two stage and the one stage method of the gasification arrangement with only the upward moving bed (co-current updraft). The main novel features of the gasifier conception include grate-less reactor, upward moving bed of biomass particles (e.g. pellets) by means of a screw elevator with changeable rotational speed and gradual expanding diameter of the cylindrical reactor in the part above the upper end of the screw. The gasifier concept and arrangement are considered convenient for thermal power range 100-350 kW{sub th}. The second stage of the gasifier served mainly for tar compounds destruction/reforming by increased temperature (around 950 Degree-Sign C) and for gasification reaction of the fuel gas with char. The second stage used additional combustion of the fuel gas by preheated secondary air for attaining higher temperature and faster gasification of the remaining char from the first stage. The measurements of gas composition and tar compound contents confirmed superiority of the two stage gasification system, drastic decrease of aromatic compounds with two and higher number of benzene rings by 1-2 orders. On the other hand the two stage gasification (with overall ER = 0.71) led to substantial reduction of gas heating value (LHV = 3.15 MJ/Nm{sup 3}), elevation of gas volume and increase of nitrogen content in fuel gas. The increased temperature (>950 Degree-Sign C) at the entrance to the char bed caused also substantial decrease of ammonia content in fuel gas. The char with higher content of ash leaving the second stage presented only few mass% of the inlet biomass stream.« less

Brief communication: sliding displacement of amnion and chorion following controlled laser wounding suggests a mechanism for short-term sealing of ruptured membranes.

PubMed

Behzad, F; Dickinson, M R; Charlton, A; Aplin, J D

1994-10-01

The Erbium-YAG laser was used to produce narrow wounds of defined depth in term amniochorion. The charring effect of the laser meant that sites could be readily localized in histological sections. During brief post-wounding incubations, sliding displacement of the amnion relative to the chorion occurred through the plane of the spongy layer. This suggests a possible short-term mechanism whereby a spontaneous rupture could be sealed in vivo.

A users manual for a revised version of the Langley charring ablator program

NASA Technical Reports Server (NTRS)

Stroud, C. W.; Brinkley, K. L.

1975-01-01

A computer program is described that will compute the transient response of a thermal protection material to a prescribed heat input at the surface. The program has the capability of analyzing pyrolysis gas chemical kinetics in detail and treating pyrolysis reactions-in-depth. Deposition of solid products produced by chemical reactions in the gas phase is included in the analysis. An outline is given for the theory. detailed operating instructions for the computer program are included.

Time domain-nuclear magnetic resonance study of chars from southern hardwoods

Treesearch

Thomas Elder; Nicole Labbe; David Harper; Timothy Rials

2006-01-01

Chars from the thermal degradation of silver maple (Acer saccharinum), red maple (Acer rubrum), sugar maple (Acer saccharum), and white oak (Quercus spp.), performed at temperatures from 250 to 350 oC, were examined using time domain-nuclear magnetic resonance...

Radiocarbon studies of latest Pleistocene and Holocene lava flows of the Snake River Plain, Idaho: Data, lessons, interpretations

USGS Publications Warehouse

Kuntz, M.A.; Spiker, E. C.; Rubin, M.; Champion, D.E.; Lefebvre, R.H.

1986-01-01

Latest Pleistocene-Holocene basaltic lava fields of the Snake River Plain, Idaho, have been dated by the radiocarbon method. Backhoe excavations beneath lava flows typically yielded carbon-bearing, charred eolian sediment. This material provided most of the samples for this study; the sediment typically contains less than 0.2% carbon. Charcoal fragments were obtained from tree molds but only from a few backhoe excavations. Contamination of the charred sediments and charcoal by younger carbon components is extensive; the effects of contamination were mitigated but appropriate pretreatment of samples using acid and alkali leaches. Twenty of the more than 60 lava flows of the Craters of the Moon lava field have been dated; their ages range from about 15,000 to about 2000 yr B.P. The ages permit assignment of the flows to eight distinct eruptive periods with an average recurrence interval of about 2000 yr. The seven other latest Pleistocene-Holocene lava fields were all emplaced in short eruptive bursts. Their 14C ages (yr B.P.) are: Kings Bowl (2222?? 100), Wapi (2270 ?? 50), Hells Half Acre (5200 ?? 150), Shoshone (10,130 ?? 350), North Robbers and South Robbers (11.980 ?? 300), and Cerro Grande (13,380 ?? 350). ?? 1986.

Radiocarbon studies of latest Pleistocene and Holocene lava flows of the Snake River Plain, Idaho: Data, lessons, interpretations

NASA Astrophysics Data System (ADS)

Kuntz, Mel A.; Spiker, Elliott C.; Rubin, Meyer; Champion, Duane E.; Lefebvre, Richard H.

1986-03-01

Latest Pleistocene-Holocene basaltic lava fields of the Snake River Plain, Idaho, have been dated by the radiocarbon method. Backhoe excavations beneath lava flows typically yielded carbon-bearing, charred eolian sediment. This material provided most of the samples for this study; the sediment typically contains less than 0.2% carbon. Charcoal fragments were obtained from tree molds but only from a few backhoe excavations. Contamination of the charred sediments and charcoal by younger carbon components is extensive; the effects of contamination were mitigated but appropriate pretreatment of samples using acid and alkali leaches. Twenty of the more than 60 lava flows of the Craters of the Moon lava field have been dated; their ages range from about 15,000 to about 2000 yr B.P. The ages permit assignment of the flows to eight distinct eruptive periods with an average recurrence interval of about 2000 yr. The seven other latest Pleistocene-Holocene lava fields were all emplaced in short eruptive bursts. Their 14C ages (yr B.P.) are: Kings Bowl (2222± 100), Wapi (2270 ± 50), Hells Half Acre (5200 ± 150), Shoshone (10,130 ± 350), North Robbers and South Robbers (11.980 ± 300), and Cerro Grande (13,380 ± 350).

Assessment of relative flammability and thermochemical properties of some thermoplastic materials

NASA Technical Reports Server (NTRS)

Kourtides, D. A.; Parker, J. A.

1977-01-01

Thermomechanical properties, flammability, oxygen index, relative toxicity of pyrolysis effluents, and char yields were studied for 12 advanced polymers which are candidates for use in aircraft interiors as decorative films, compression- and injection-molded parts and thermoplastic parts. Polymers sampled included polyphenylene sulfide, 9,9 bis (4-hydroxyphenol) fluorene polycarbonate-poly (dimethylsiloxane), polyether sulfone, polyvinyl fluoride and polyvinylidene fluoride. Availability of these samples, whether in commercial form or in test quantities, is specified. An estimate of relative fire resistance for the materials was obtained; the five polymers listed above were found to be the most fire resistant of the 12 sampled.

iQOS: evidence of pyrolysis and release of a toxicant from plastic.

PubMed

Davis, Barbara; Williams, Monique; Talbot, Prue

2018-03-13

To evaluate performance of the I quit original smoking (iQOS) heat-not-burn system as a function of cleaning and puffing topography, investigate the validity of manufacturer's claims that this device does not burn tobacco and determine if the polymer-film filter is potentially harmful. iQOS performance was evaluated using five running conditions incorporating two different cleaning protocols. Heatsticks were visually and stereomicroscopically inspected preuse and postuse to determine the extent of tobacco plug charring (from pyrolysis) and polymer-film filter melting, and to elucidate the effects of cleaning on charring. Gas chromatography-mass spectrometry headspace analysis was conducted on unused polymer-film filters to determine if potentially toxic chemicals are emitted from the filter during heating. For all testing protocols, pressure drop decreased as puff number increased. Changes in testing protocols did not affect aerosol density. Charring due to pyrolysis (a form of organic matter thermochemical decomposition) was observed in the tobacco plug after use. When the manufacturer's cleaning instructions were followed, both charring of the tobacco plug and melting of the polymer-film filter increased. Headspace analysis of the polymer-film filter revealed the release of formaldehyde cyanohydrin at 90°C, which is well below the maximum temperature reached during normal usage. Device usage limitations may contribute to decreases in interpuff intervals, potentially increasing user's intake of nicotine and other harmful chemicals. This study found that the tobacco plug does char and that charring increases when the device is not cleaned between heatsticks. Release of formaldehyde cyanohydrin is a concern as it is highly toxic at very low concentrations. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

High-Quality Hollow Closed-Pore Silica Antireflection Coatings Based on Styrene-Acrylate Emulsion @ Organic-Inorganic Silica Precursor.

PubMed

Guo, Zhaolong; Zhao, Haixin; Zhao, Wei; Wang, Tao; Kong, Depeng; Chen, Taojing; Zhang, Xiaoyan

2016-05-11

Making use of a facile and low-cost way for the preparation of a hierarchically organized novel hollow closed-pore silica antireflective coating (CHAR) with tailored optical properties and a mechanical reliability is of great interest in the field of solar photovoltaic technology. The process mainly contains two aspects: (1) a styrene-acrylate emulsion @ organic-inorganic silica precursor (SA@OISP) core/shell hierarchical nanostructure, consisting of a sacrificial styrene-acrylate (SA) primary template, was fabricated using a sol-gel method; (2) the self-assembly of the nanostructures leads to SA@OISP nanospheres forming the high-quality hollow closed-pore silica antireflection coating (CHAR) by a dip-coating process and a subsequent calcination treatment. The resulting SA@OISP nanospheres have a mean diameter of 65.2 nm and contained a SA soft core with a mean diameter of approximately 54.8 nm and an organic-inorganic silica precursor (OISP) shell with a thickness of approximately 6-10 nm. Furthermore, the prepared CHAR film exhibited a high transmittance and good ruggedness. An average transmittance (TAV) of 97.64% was obtained, and the value is close to the ideal single-layered antireflection coating (98.09%) over a broad range of wavelengths (from 380 to 1100 nm). The CHAR film showed a stable TAV, with attenuation values of less than 0.8% and 0.43% after the abrasion test and the damp heat test, respectively. The conversion efficiency of the CHAR coating cover solar modules tends to be increased by 3.75%. The promising results obtained in this study suggest that the CHAR film was considered as an essential component of the solar module and were expected to provide additional solar energy harvest under extreme outdoor climates.

Towards User-Friendly Spelling with an Auditory Brain-Computer Interface: The CharStreamer Paradigm

PubMed Central

Höhne, Johannes; Tangermann, Michael

2014-01-01

Realizing the decoding of brain signals into control commands, brain-computer interfaces (BCI) aim to establish an alternative communication pathway for locked-in patients. In contrast to most visual BCI approaches which use event-related potentials (ERP) of the electroencephalogram, auditory BCI systems are challenged with ERP responses, which are less class-discriminant between attended and unattended stimuli. Furthermore, these auditory approaches have more complex interfaces which imposes a substantial workload on their users. Aiming for a maximally user-friendly spelling interface, this study introduces a novel auditory paradigm: “CharStreamer”. The speller can be used with an instruction as simple as “please attend to what you want to spell”. The stimuli of CharStreamer comprise 30 spoken sounds of letters and actions. As each of them is represented by the sound of itself and not by an artificial substitute, it can be selected in a one-step procedure. The mental mapping effort (sound stimuli to actions) is thus minimized. Usability is further accounted for by an alphabetical stimulus presentation: contrary to random presentation orders, the user can foresee the presentation time of the target letter sound. Healthy, normal hearing users (n = 10) of the CharStreamer paradigm displayed ERP responses that systematically differed between target and non-target sounds. Class-discriminant features, however, varied individually from the typical N1-P2 complex and P3 ERP components found in control conditions with random sequences. To fully exploit the sequential presentation structure of CharStreamer, novel data analysis approaches and classification methods were introduced. The results of online spelling tests showed that a competitive spelling speed can be achieved with CharStreamer. With respect to user rating, it clearly outperforms a control setup with random presentation sequences. PMID:24886978

Phytolith aided paleoenvironmental studies from the Dutch Neolithic

NASA Astrophysics Data System (ADS)

Persaits, Gergő; Gulyás, Sándor; Náfrádi, Katalin; Sümegi, Pál; Szalontai, Csaba

2015-11-01

There is increasing evidence for crop cultivation at sites of the Neolithic Swifterbant culture from ca. 4300 B.C. onwards. Presence of cereal fields at the Swifterbant S2, S3 and S4 sites has been corroborated from micro morphological studies of soil samples. Swifterbant sites with evidence for cultivated plants are still scarce though and only emerging, and have produced very low numbers of charred cereals only. The major aim of our work was to elucidate the environmental background of the Dutch Neolithic site Swifterbant S4 based on the investigation of phytolith remains retrieved from soil samples. In addition to find evidence for crop cultivation independently from other studies. Samples were taken at 1 cm intervals vertically from the soil section at the central profile of site S4. Additional samples were taken from pocket-like structures and adjacent horizons above and below. Pig coprolites yielded an astonishing phytolith assemblage which was compared to that of the soil samples. A pig tooth also yielded evaluable material via detailed investigation using SEM. The evaluation of phytolith assemblages retrieved from the soil horizons plus those ending up in the droppings of pigs feasting in the area enabled to draw a relatively reliable environmental picture of the area. All these refer to the presence of a Neolithic horticulture (cereal cultivation) under balanced micro-climatic conditions as a result of the vicinity of the nearby floodplain. These findings corroborate those of previous soil micro-morphological studies.

Co-hydrothermal treatment of fallen leaves with iron sludge to prepare magnetic iron product and solid fuel.

PubMed

Gu, Lin; Li, Binglian; Wen, Haifeng; Zhang, Xin; Wang, Liang; Ye, Jianfeng

2018-06-01

The hydrothermal carbonization (HTC) was performed on Metasequoia Leaves (ML) in the presence of iron sludge, both of which were generated as solid residuals. The relations between sludge, char's properties and operating conditions were systemically investigated. Iron sludge primarily catalyzed the efficient formation of char with higher heating value (HHV) becoming 1.15-1.65 times of ML (18.21 MJ/kg) and was meanwhile reduced to magnetite. The hydrated Fe ions in octahedron crystals acted as nucleophiles facilitating the dehydration and decarboxylation reactions. The increased HHV is found strong temperature dependent while prolonging the residence time is more preferable for low organic acids generation. Thermogravimetric analysis confirmed the iron sludge enhanced conversion of volatile to fixed carbon. The as-prepared solid char showed better stability after catalytic HTC treatment, having ignition temperature increased from 253 to 426 °C as compared to the char prepared without iron sludge addition. Copyright © 2018 Elsevier Ltd. All rights reserved.

An analysis of a charring ablator with thermal nonequilibrium, chemical kinetics, and mass transfer

NASA Technical Reports Server (NTRS)

Clark, R. K.

1973-01-01

The differential equations governing the transient response of a one-dimensional ablative thermal protection system are presented for thermal nonequilibrium between the pyrolysis gases and the char layer and with finite rate chemical reactions occurring. The system consists of three layers (the char layer, the uncharred layer, and an optical insulation layer) with concentrated heat sinks at the back surface and between the second and third layers. The equations are solved numerically by using a modified implicit finite difference scheme to obtain solutions for the thickness of the charred and uncharred layers, surface recession and pyrolysis rates, solid temperatures, porosity profiles, and profiles of pyrolysis-gas temperature, pressure, composition, and flow rate. Good agreement is obtained between numerical results and exact solutions for a number of simplified cases. The complete numerical analysis is used to obtain solutions for an ablative system subjected to a constant heating environment. Effects of thermal, chemical, and mass transfer processes are shown.

Torrefaction of agriculture straws and its application on biomass pyrolysis poly-generation.

PubMed

Chen, Yingquan; Yang, Haiping; Yang, Qing; Hao, Hongmeng; Zhu, Bo; Chen, Hanping

2014-03-01

This study investigated the properties of corn stalk and cotton stalk after torrefaction, and the effects of torrefaction on product properties obtained under the optimal condition of biomass pyrolysis polygeneration. The color of the torrefied biomass chars darkened, and the grindability was upgraded, with finer particles formed and grinding energy consumption reduced. The moisture and oxygen content significantly decreased whereas the carbon content increased considerably. It was found that torrefaction had different effects on the char, liquid oil and biogas from biomass pyrolysis polygeneration. Compared to raw straws, the output of chars from pyrolysis of torrefied straws increased and the quality of chars as a solid fuel had no significant change, while the output of liquid oil and biogas decreased. The liquid oil contained more concentrated phenols with less water content below 40wt.%, and the biogas contained more concentrated H2 and CH4 with higher LHV up to 15MJ/nm(3). Copyright © 2014 Elsevier Ltd. All rights reserved.

Physicochemical evolution during rice straw and coal co-pyrolysis and its effect on co-gasification reactivity.

PubMed

Wei, Juntao; Gong, Yan; Guo, Qinghua; Ding, Lu; Wang, Fuchen; Yu, Guangsuo

2017-03-01

Physicochemical evolution (i.e. pore structure variation, carbon structure change and active AAEM transformation) during rice straw (RS) and Shenfu bituminous coal (SF) co-pyrolysis was quantitatively determined in this work. Moreover, the corresponding char gasification was conducted using a thermogravimetric analyzer (TGA) and relative reactivity was proposed to quantify the co-pyrolysis impact on co-gasification reactivity. The results showed that the development of pore structure in co-pyrolyzed chars was first inhibited and then enhanced with the decrease of SF proportion. The promotion effect of co-pyrolysis on order degree of co-pyrolyzed chars gradually weakened with increasing RS proportion. Co-pyrolysis mainly enhanced active K transformation in co-pyrolyzed chars and the promotion effect was alleviated with increasing RS proportion. The inhibition effect of co-pyrolysis on co-gasification reactivity weakened with increasing RS proportion and gasification temperature, which was mainly attributed to the combination of carbon structure evolution and active AAEM transformation in co-pyrolysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Influence of Temperature on Pyrolysis of Biomass

NASA Astrophysics Data System (ADS)

Kumar, S.; Pattnaik, D.; Bhuyan, S. K.; Mishra, S. C.

2018-03-01

The Antimicrobial and anti-inflammatory nature of the castor oil is used for the treatment of constipation and also used to clean the intestine before a surgical treatment. The growing demand castor oil due to its cheaper price and have much demand to grow hairs faster which give proteins to hair and increases the life span of hair and increases the hair capacity and provide hair smoothness because it has high ricinoleic ratio which is beneficial for skin and hair. The main objective of this paper is by observing its usefulness and the current aim for the research work is to produce bio-char/carbon compounds and extraction of higher carbon content. The castor leaves are collected and dried in the sun light to get it moisture free and proximate analysis is studied that reveals 14% of fixed amount of carbon. The dried leaves of castor plant are pyrolized at different temperature ranges 250°C, 350 °C, 450°C, 600°C and 900°C. The pyrolised specimens were studied by Fourier-transform infrared spectroscopy analysis which shows the transformation and formation of several bonds including carbon bonds which are affected during carbonization. Scanning electron microscope and energy dispersive x-ray spectroscopy have been studied on pyrolised specimen to get microstructures elements in the bio-char. The parameter called carbon/oxygen ration gives the advantage of char in the agricultural land for fertility motive and discrepancy of carbon and oxygen contents have been analysed. It has been found that carbon/oxygen ration increased along increment in Pyrolysis tempt. Up to 500°C and therefore along moreover increment in tempt. Beyond 500°C there is a decrement trend has been found.

Particle-Sizing System for Scanning Electron Microscope Images of Solid- Propellant Combustion Exhaust

DTIC Science & Technology

1991-03-01

bl2[3]; 1* ditto */ char b13(61, b1413]; /* unused at the moment ~ char bl5(3], b16 (3], b17[31, b18[3]; /* YIN input buffers * char bl9[3], b20[3...gbool(SET,frm,13,wn.10, 1, ’ALL: Enable HELP screens (Y,N] fatrib,’ - ,&HELPLVL,bl5,NSTR,NSTR); bool2YN(DOSEQ, b16 ); wngbool(SET,frm,14,wn,ll, l,’SEMEX...CLIP, TAG and SIZE without asking[Y.N): fatrib,’ ’ ,&DOSEQ, bl6 ,NSTR.NSTR): bool2YN(DFINVERT,b17); wngbool(SET,frm,15,wn,12, 1, ACQUIRE: Complement

Considerations Based on Reaction Rate on Char Gasification Behavior in Two-stage Gasifier for Biomass

NASA Astrophysics Data System (ADS)

Taniguchi, Miki; Nishiyama, Akio; Sasauchi, Kenichi; Ito, Yusuke; Akamatsu, Fumiteru

In order to develop a small-scale gasifier in which biomass can be converted to energy with high efficiency, we planned a gasification process that consists of two parts: pyrolysis part (rotary kiln) and gasification part (downdraft gasifier). We performed fundamental experiments on gasification part and discussed the appropriate conditions such as air supply location, air ratio, air temperature and hearth load. We considered the results by calculating reaction rates of representative reactions on char gasification part and found that water gas reaction is dominant in the reduction area and its behavior gives important information to decide the adequate length of the char layer.

Numerical analysis of the transient response of an axisymmetric ablative char layer considering internal flow effects

NASA Technical Reports Server (NTRS)

Pittman, C. M.; Howser, L. M.

1972-01-01

The differential equations governing the transient response of the char layer of an ablating axisymmetric body, internal pyrolysis gas flow effects being considered, have been derived. These equations have been expanded into finite difference form and programed for numerical solution on a digital computer. Numerical results compare favorably with simplified exact solutions. The complete numerical analysis was used to obtain solutions for two representative body shapes subjected to a typical entry heating environment. Pronounced effects of the lateral flow of pyrolysis gases on the mass flow field within the char layer and the associated surface and pyrolysis interface recession rates are shown.

Pyrolysis of forest residues: An approach to techno-economics for bio-fuel production

DOE PAGES

Carrasco, Jose L.; Gunukula, Sampath; Boateng, Akwasi A.; ...

2017-04-01

Here, the techno-economics for producing liquid fuels from Maine forest residues were determined from a combination of: (1) laboratory experiments at USDA-ARS’s Eastern Regional Research Center using hog fuel (a secondary woody residue produced from mill byproducts such as sawdust, bark and shavings) as a feedstock for pyrolysis to establish product yields and composition, and (2) Aspen Plus® process simulation for a feed rate of 2000 dry metric tons per day to estimate energy requirements and equipment sizes. The simulated plant includes feedstock sizing and drying, pyrolysis, hydrogen production and hydrotreatment of pyrolysis oils. The biomass is converted into bio-oilmore » (61% yield), char (24%) and gases (15%) in the pyrolysis reactor, with an energy demand of 17%. The bio-oil is then hydrotreated to remove oxygen, thereby producing hydrocarbon fuels. The final mass yield of gasoline/diesel hydrocarbons is 16% with a 40% energy yield based on the dry biomass fed, this yield represents a fuel production of 51.9 gallons per dry metric ton of feedstock. A unique aspect of the process simulated herein is that pyrolysis char and gases are used as sources for both thermal energy and hydrogen, greatly decreasing the need to input fossil energy. The total capital investment for a grass-roots plant was estimated to be US$427 million with an annual operational cost of US$154 million. With a 30 year project life, a minimum fuel selling price was determined to be US$6.25 per gallon. The economic concerns are related to high capital costs, high feedstock costs and short hydrotreating catalyst lifetimes.« less

Characterization of cellulosic wastes and gasification products from chicken farms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joseph, Paul, E-mail: p.joseph@ulster.ac.uk; Tretsiakova-McNally, Svetlana; McKenna, Siobhan

Highlights: Black-Right-Pointing-Pointer The gas chromatography indicated the variable quality of the producer gas. Black-Right-Pointing-Pointer The char had appreciable NPK values, and can be used as a fertiliser. Black-Right-Pointing-Pointer The bio-oil produced was of poor quality, having high moisture content and low pH. Black-Right-Pointing-Pointer Mass and energy balances showed inadequate level energy recovery from the process. Black-Right-Pointing-Pointer Future work includes changing the operating parameters of the gasification unit. - Abstract: The current article focuses on gasification as a primary disposal solution for cellulosic wastes derived from chicken farms, and the possibility to recover energy from this process. Wood shavings and chickenmore » litter were characterized with a view to establishing their thermal parameters, compositional natures and calorific values. The main products obtained from the gasification of chicken litter, namely, producer gas, bio-oil and char, were also analysed in order to establish their potential as energy sources. The experimental protocol included bomb calorimetry, pyrolysis combustion flow calorimetry (PCFC), thermo-gravimetric analyses (TGA), differential scanning calorimetry (DSC), Fourier transform infrared (FT-IR) spectroscopy, Raman spectroscopy, elemental analyses, X-ray diffraction (XRD), mineral content analyses and gas chromatography. The mass and energy balances of the gasification unit were also estimated. The results obtained confirmed that gasification is a viable method of chicken litter disposal. In addition to this, it is also possible to recover some energy from the process. However, energy content in the gas-phase was relatively low. This might be due to the low energy efficiency (19.6%) of the gasification unit, which could be improved by changing the operation parameters.« less

Pyrolysis of forest residues: An approach to techno-economics for bio-fuel production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carrasco, Jose L.; Gunukula, Sampath; Boateng, Akwasi A.

Here, the techno-economics for producing liquid fuels from Maine forest residues were determined from a combination of: (1) laboratory experiments at USDA-ARS’s Eastern Regional Research Center using hog fuel (a secondary woody residue produced from mill byproducts such as sawdust, bark and shavings) as a feedstock for pyrolysis to establish product yields and composition, and (2) Aspen Plus® process simulation for a feed rate of 2000 dry metric tons per day to estimate energy requirements and equipment sizes. The simulated plant includes feedstock sizing and drying, pyrolysis, hydrogen production and hydrotreatment of pyrolysis oils. The biomass is converted into bio-oilmore » (61% yield), char (24%) and gases (15%) in the pyrolysis reactor, with an energy demand of 17%. The bio-oil is then hydrotreated to remove oxygen, thereby producing hydrocarbon fuels. The final mass yield of gasoline/diesel hydrocarbons is 16% with a 40% energy yield based on the dry biomass fed, this yield represents a fuel production of 51.9 gallons per dry metric ton of feedstock. A unique aspect of the process simulated herein is that pyrolysis char and gases are used as sources for both thermal energy and hydrogen, greatly decreasing the need to input fossil energy. The total capital investment for a grass-roots plant was estimated to be US$427 million with an annual operational cost of US$154 million. With a 30 year project life, a minimum fuel selling price was determined to be US$6.25 per gallon. The economic concerns are related to high capital costs, high feedstock costs and short hydrotreating catalyst lifetimes.« less

Experimental investigation on IXV TPS interface effects in Plasmatron

NASA Astrophysics Data System (ADS)

Ceglia, Giuseppe; Trifoni, Eduardo; Gouriet, Jean-Baptiste; Chazot, Olivier; Mareschi, Vincenzo; Rufolo, Giuseppe; Tumino, Giorgio

2016-06-01

An experimental investigation related to the thermal protection system (TPS) interfaces of the intermediate experimental vehicle has been carried out in the Plasmatron facility at the von Karman Institute for fluid dynamics. The objective of this test campaign is to qualify the thermal behaviours of two different TPS interfaces under flight representative conditions in terms of heat flux and integral heat load ( 180 kW/m2 for 700 s). Three test samples are tested in off-stagnation configuration installed on an available flat plate holder under the same test conditions. The first junction is composed of an upstream ceramic matrix composite (CMC) plate and an ablative P50 cork composite block separated by a gap of 2 mm. The second one is made of an upstream P50 block and a downstream ablative SV2A silicon elastomer block with silicon-based filler in between. A sample composed of P50 material is tested in order to obtain reference results without TPS interface effect. The overheating at the CMC-P50 interface due to the jump of the catalytic properties of the materials, and the recession/swelling behaviour of the P50-SV2A interface are under investigation. All the test samples withstand relatively well the imposed heat flux for the test duration. As expected, both the ablative materials undergo a thermal degradation. The P50 exhibits the formation of a porous char layer and its recession; on the other hand, the SV2A swells and forms a fragile char layer.

Biochar Treatment Resulted in a Combined Effect on Soybean Growth Promotion and a Shift in Plant Growth Promoting Rhizobacteria

PubMed Central

Egamberdieva, Dilfuza; Wirth, Stephan; Behrendt, Undine; Abd_Allah, Elsayed F.; Berg, Gabriele

2016-01-01

The application of biochar to soil is considered to have the potential for long-term soil carbon sequestration, as well as for improving plant growth and suppressing soil pathogens. In our study we evaluated the effect of biochar on the plant growth of soybeans, as well as on the community composition of root-associated bacteria with plant growth promoting traits. Two types of biochar, namely, maize biochar (MBC), wood biochar (WBC), and hydrochar (HTC) were used for pot experiments to monitor plant growth. Soybean plants grown in soil amended with HTC char (2%) showed the best performance and were collected for isolation and further characterization of root-associated bacteria for multiple plant growth promoting traits. Only HTC char amendment resulted in a statistically significant increase in the root and shoot dry weight of soybeans. Interestingly, rhizosphere isolates from HTC char amended soil showed higher diversity than the rhizosphere isolates from the control soil. In addition, a higher proportion of isolates from HTC char amended soil compared with control soil was found to express plant growth promoting properties and showed antagonistic activity against one or more phytopathogenic fungi. Our study provided evidence that improved plant growth by biochar incorporation into soil results from the combination of a direct effect that is dependent on the type of char and a microbiome shift in root-associated beneficial bacteria. PMID:26941730

Changes imposed by pyrolysis, thermal gasification and incineration on composition and phosphorus fertilizer quality of municipal sewage sludge.

PubMed

Thomsen, Tobias Pape; Sárossy, Zsuzsa; Ahrenfeldt, Jesper; Henriksen, Ulrik B; Frandsen, Flemming J; Müller-Stöver, Dorette Sophie

2017-08-01

Fertilizer quality of ash and char from incineration, gasification and pyrolysis of a single municipal sewage sludge sample were investigated by comparing composition and phosphorus (P) plant availability. A process for post oxidation of gasification ash and pyrolysis char was developed and the oxidized materials were investigated as well. Sequential extraction with full elemental balances of the extracted pools as well as scanning electron microscopy with energy dispersive X-ray spectroscopy were used to investigate the mechanisms driving the observed differences in composition and P plant availability in a short-term soil incubation study. The compositional changes related mainly to differences in the proximate composition as well as to the release of especially nitrogen, sulfur, cadmium and to some extent, phosphorus (P). The cadmium load per unit of P was reduced with 75-85% in gasification processes and 10-15% in pyrolysis whereas no reduction was observed in incineration processes. The influence on other heavy metals was less pronounced. The plant availability of P in the substrates varied from almost zero to almost 100% of the plant availability of P in the untreated sludge. Post-oxidized slow pyrolysis char was found to be the substrate with the highest P fertilizer value while ash from commercial fluid bed sludge incineration had the lowest P fertilizer quality. The high P fertilizer value in the best substrate is suggested to be a function of several different mechanisms including structural surface changes and improvements in the association of P to especially magnesium, calcium and aluminum. Copyright © 2017 Elsevier Ltd. All rights reserved.

40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) GUM AND WOOD CHEMICALS...

EVALUATION OF TRADITIONAL CHARCOALS AND GASIFIER BIOCHARS AS SUSTAINABLE LOW-COST ADSORBENTS FOR WATER TREATMENT SERVING DEVELOPING COMMUNITIES

EPA Science Inventory

This research will break new ground in elucidating connections between principal char manufacture variables and the development of enhanced sorption characteristics in the char product. These variables include feedstock identity (biomass precursor) and form (i.e., whole log...

40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) GUM AND WOOD CHEMICALS...

40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) GUM AND WOOD CHEMICALS...

40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GUM AND WOOD CHEMICALS...

MOLECULAR TRACERS FOR SMOKE FROM CHARRING/BURNING OF CHITIN BIOPOLYMER. (R823990)

EPA Science Inventory

Abstract

Monosaccharide derivatives from the breakdown of cellulose are the major organic components of smoke particles emitted to the atmosphere from biomass burning. In urban areas a related biopolymer, chitin, may contribute markers to smoke from grilling/charring o...

Kim Magrini | NREL

Science.gov Websites

Developing char-based soil amendments Soil carbon and char analysis via molecular beam mass spectrometry depth profiling, Fourier transform infrared [FTIR]) Rapid soil carbon analysis using analytical DRIFTS, 13C NMR, and py-MBMS to Characterize the Effects of Soil Science Oxidation Assays on Soil Organic

USE OF BONE CHAR FOR THE REMOVAL OF ARSENIC AND URANIUM FROM GROUNDWATER ATTHE PINE RIDGE RESERVATION

EPA Science Inventory

Using bench scale U removal capacity data with bone char, a preliminary point-of-use filter was developed using theoretical calculations. The design specifications were completed for the filter, and the manufacturing of the preliminary filter is currently underway. Through ...

40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GUM AND WOOD CHEMICALS...

A study on pyrolysis of Canada thistle (Cirsium arvense) with titania based catalysts for bio-fuel production.

PubMed

Aysu, Tevfik

2016-11-01

The catalytic pyrolysis of Cirsium arvense was performed with titania supported catalysts under the operating conditions of 500°C, 40°C/min heating rate, 100mL/min N2 flow rate in a fixed bed reactor for biofuel production. The effect of catalysts on product yields was investigated. The amount of pyrolysis products (bio-char, bio-oil, gas) and the composition of the produced bio-oils were determined by proton nuclear magnetic resonance ((1)H NMR), Fourier transform infrared spectroscopy (FT-IR), gas chromatography/mass spectrometry (GC-MS) and elemental analysis (EA) techniques. Thistle bio-oils had lower O/C and H/C molar ratios compared to feedstock. The highest bio-char and bio-oil yields of 29.32wt% and 36.71wt% were obtained in the presence of Ce/TiO2 and Ni/TiO2 catalysts respectively. GC-MS identified 97 different compounds in the bio-oils obtained from thistle pyrolysis. (1)H NMR analysis showed that the bio-oils contained ∼55-77% aliphatic and ∼6-19% aromatic structural units. Copyright © 2016 Elsevier Ltd. All rights reserved.

Enrichment of bio-oil after hydrothermal liquefaction (HTL) of microalgae C. vulgaris grown in wastewater: Bio-char and post HTL wastewater utilization studies.

PubMed

Arun, Jayaseelan; Varshini, Padmanabhan; Prithvinath, P Kamath; Priyadarshini, Venkataramani; Gopinath, Kannappan Panchamoorthy

2018-08-01

In this study, bio-oil was produced through hydrothermal liquefaction (HTL) of C. vulgaris biomass cultivated in wastewater and was enriched into transportation fuels. Bio-oil yield was 29.37% wt at 300 °C, 60 min, at 15 g/200 mL biomass loading rate with 3% wt nano ZnO catalyst loading. Applying catalyst reduced oxygen and nitrogen content in bio-oil and increased its calorific value (19.6 ± 0.8 MJ/Kg). Bio-oil was enriched through liquid-liquid extraction (LLE) and higher yield was obtained at 30 °C for dichloromethane solvent (18.2% wt). Compounds of enriched oil were within the petro-diesel range (C 8 -C 21 ). Bio-char after HTL process was activated and used as adsorbent in wastewater treatment process to remove organic pollutants (COD, NO 3 , NH 3 and PO 4 ). Treated wastewater can be supplied as growth medium for microalgae cultivation in further experiments. Nearly 3-4 times the nanocatalyst can be reused in the HTL process. Copyright © 2018 Elsevier Ltd. All rights reserved.

Combined goal gasifier and fuel cell system and method

DOEpatents

Gmeindl, Frank D.; Geisbrecht, Rodney A.

1990-01-01

A molten carbonate fuel cell is combined with a catalytic coal or coal char gasifier for providing the reactant gases comprising hydrogen, carbon monoxide and carbon dioxide used in the operation of the fuel cell. These reactant gases are stripped of sulfur compounds and particulate material and are then separated in discrete gas streams for conveyance to appropriate electrodes in the fuel cell. The gasifier is arranged to receive the reaction products generated at the anode of the fuel cell by the electricity-producing electrochemical reaction therein. These reaction products from the anode are formed primarily of high temperature steam and carbon dioxide to provide the steam, the atmosphere and the heat necessary to endothermically pyrolyze the coal or char in the presence of a catalyst. The reaction products generated at the cathode are substantially formed of carbon dioxide which is used to heat air being admixed with the carbon dioxide stream from the gasifier for providing the oxygen required for the reaction in the fuel cell and for driving an expansion device for energy recovery. A portion of this carbon dioxide from the cathode may be recycled into the fuel cell with the air-carbon dioxide mixture.