[A novel biologic electricity signal measurement based on neuron chip].

PubMed

Lei, Yinsheng; Wang, Mingshi; Sun, Tongjing; Zhu, Qiang; Qin, Ran

2006-06-01

Neuron chip is a multiprocessor with three pipeline CPU; its communication protocol and control processor are integrated in effect to carry out the function of communication, control, attemper, I/O, etc. A novel biologic electronic signal measurement network system is composed of intelligent measurement nodes with neuron chip at the core. In this study, the electronic signals such as ECG, EEG, EMG and BOS can be synthetically measured by those intelligent nodes, and some valuable diagnostic messages are found. Wavelet transform is employed in this system to analyze various biologic electronic signals due to its strong time-frequency ability of decomposing signal local character. Better effect is gained. This paper introduces the hardware structure of network and intelligent measurement node, the measurement theory and the signal figure of data acquisition and processing.

Comparisons between Intel 386 and i486 microprecessors

NASA Technical Reports Server (NTRS)

Liu, Yuan-Kwei

1989-01-01

A quick and preliminary comparison is made between the Intel 386 and i486 microprocessors. The following topics are discussed: the i486 key elements, comparison of instruction set architecture, the i486 on-chip cache characteristics, the i486 multiprocessor support, comparison of performance, comparison of power consumption, comparison of radiation hardening potential, and recommendations for the Space Station Freedom (SSF) Data Management System (DMS).

Monoatomic layer removal mechanism in chemical mechanical polishing process: A molecular dynamics study

NASA Astrophysics Data System (ADS)

Si, Lina; Guo, Dan; Luo, Jianbin; Lu, Xinchun

2010-03-01

Molecular dynamics simulations of nanoscratching processes were used to study the atomic-scale removal mechanism of single crystalline silicon in chemical mechanical polishing (CMP) process and particular attention was paid to the effect of scratching depth. The simulation results under a scratching depth of 1 nm showed that a thick layer of silicon material was removed by chip formation and an amorphous layer was formed on the silicon surface after nanoscratching. By contrast, the simulation results with a depth of 0.1 nm indicated that just one monoatomic layer of workpiece was removed and a well ordered crystalline surface was obtained, which is quite consistent with previous CMP experimental results. Therefore, monoatomic layer removal mechanism was presented, by which it is considered that during CMP process the material was removed by one monoatomic layer after another, and the mechanism could provide a reasonable understanding on how the high precision surface was obtained. Also, the effects of the silica particle size and scratching velocity on the removal mechanism were investigated; the wear regimes and interatomic forces between silica particle and workpiece were studied to account for the different removal mechanisms with indentation depths of 0.1 and 1 nm.

A Heterogeneous Multiprocessor Graphics System Using Processor-Enhanced Memories

DTIC Science & Technology

1989-02-01

frames per second, font generation directly from conic spline descriptions, and rapid calculation of radiosity form factors. The hardware consists of...generality for rendering curved surfaces, volume data, objects dcscri id with Constructive Solid Geometry, for rendering scenes using the radiosity ...f.aces and for computing a spherical radiosity lighting model (see Section 7.6). Custom Memory Chips \\ 208 bits x 128 pixels - Renderer Board ix p o a

Fabrication of pseudo-spin-MOSFETs using a multi-project wafer CMOS chip

NASA Astrophysics Data System (ADS)

Nakane, R.; Shuto, Y.; Sukegawa, H.; Wen, Z. C.; Yamamoto, S.; Mitani, S.; Tanaka, M.; Inomata, K.; Sugahara, S.

2014-12-01

We demonstrate monolithic integration of pseudo-spin-MOSFETs (PS-MOSFETs) using vendor-made MOSFETs fabricated in a low-cost multi-project wafer (MPW) product and lab-made magnetic tunnel junctions (MTJs) formed on the topmost passivation film of the MPW chip. The tunneling magnetoresistance (TMR) ratio of the fabricated MTJs strongly depends on the surface roughness of the passivation film. Nevertheless, after the chip surface was atomically flattened by SiO2 deposition on it and successive chemical-mechanical polish (CMP) process for the surface, the fabricated MTJs on the chip exhibits a sufficiently large TMR ratio (>140%) adaptable to the PS-MOSFET application. The implemented PS-MOSFETs show clear modulation of the output current controlled by the magnetization configuration of the MTJs, and a maximum magnetocurrent ratio of 90% is achieved. These magnetocurrent behaviour is quantitatively consistent with those predicted by HSPICE simulations. The developed integration technique using a MPW CMOS chip would also be applied to monolithic integration of CMOS devices/circuits and other various functional devices/materials, which would open the door for exploring CMOS-based new functional hybrid circuits.

Utilizing Dynamically Coupled Cores to Form a Resilient Chip Multiprocessor

DTIC Science & Technology

2007-06-01

requires a significant deviation from previous work. For instance, we find that using the relaxed input replication model from Reunion incurs a...Circuit Width Delay Count CRC-16 16 6.65 754 CRC- SDLC -16 16 6.10 888 CRC-32 16 7.28 2260 CRC-32 32 8.60 4240 Table 1. FO4 delay and transistor count for...the operation of our proposed system is the same in all other respects. 4.4 Compatibility Across Memory Consis- tency Models The memory consistency

A pipelined architecture for real time correction of non-uniformity in infrared focal plane arrays imaging system using multiprocessors

NASA Astrophysics Data System (ADS)

Zou, Liang; Fu, Zhuang; Zhao, YanZheng; Yang, JunYan

2010-07-01

This paper proposes a kind of pipelined electric circuit architecture implemented in FPGA, a very large scale integrated circuit (VLSI), which efficiently deals with the real time non-uniformity correction (NUC) algorithm for infrared focal plane arrays (IRFPA). Dual Nios II soft-core processors and a DSP with a 64+ core together constitute this image system. Each processor undertakes own systematic task, coordinating its work with each other's. The system on programmable chip (SOPC) in FPGA works steadily under the global clock frequency of 96Mhz. Adequate time allowance makes FPGA perform NUC image pre-processing algorithm with ease, which has offered favorable guarantee for the work of post image processing in DSP. And at the meantime, this paper presents a hardware (HW) and software (SW) co-design in FPGA. Thus, this systematic architecture yields an image processing system with multiprocessor, and a smart solution to the satisfaction with the performance of the system.

Chemical-mechanical polishing of metal and dielectric films for microelectronic applications

NASA Astrophysics Data System (ADS)

Hegde, Sharath

The demand for smaller, faster devices has led the integrated circuit (IC) industry to continually increase the device density on a chip while simultaneously reducing feature dimensions. Copper interconnects and multilevel metallization (MLM) schemes were introduced to meet some of these challenges. With the employment of MLM in the ultra-large-scale-integrated (ULSI) circuit fabrication technology, repeated planarization of different surface layers with tolerance of a few nanometers is required. Presently, chemical-mechanical planarization (CMP) is the only technique that can meet this requirement. Damascene and shallow trench isolation processes are currently used in conjunction with CMP in the fabrication of multilevel copper interconnects and isolation of devices, respectively, for advanced logic and memory devices. These processes, at some stage, require simultaneous polishing of two different materials using a single slurry that offers high polish rates, high polish selectivity to one material over the other and good post-polish surface finish. Slurries containing one kind of abrasive particles do not meet most of these demands due mainly to the unique physical and chemical properties of each abrasive. However, if a composite particle is formed that takes the advantages of different abrasives while mitigating their disadvantages, the CMP performance of resulting abrasives would be compelling. It is demonstrated that electrostatic interactions between ceria and silica particles at pH 4 can be used to produce composite particles with enhanced functionality. Zeta potential measurement and TEM images used for particle characterization show the presence of such composite particles with smaller shell particles attached onto larger core particles. Slurries containing ceria (core)/silica (shell) and silica (core)/ceria (shell) composite particles when used to polish metal and dielectric films, respectively, yield both enhanced metal and dielectric film removal rates and better post-polish surface roughness values compared to those containing single kind of particles. Several arguments are proposed to explain the enhanced CMP performance with the composite abrasives. The effect of surface charge of the composite abrasive and the hardness of the core particles in the composite abrasives contained in the polishing slurry on polish rates of different films is discussed. Also, as a part of this thesis, several issues related to CMP were addressed. The planarization ability of Cu CMP slurry containing alumina coated silica particles was studied to elucidate the role of pattern geometry in affecting polish rate and also generating pattern dependent defects like dishing and erosion. Additionally, a polishing process was devised which, when viewed with the optical profilometer, eliminated surface defects including shallow and deep scratches and pits already present in a copper film. Also, molybdenum dioxide (MoO2) was evaluated as a potential abrasive for a highly reactive copper CMP slurry with potassium iodate as the oxidizing agent. Finally, the interaction of amino acid additives in ceria slurries with the silicon nitride film during STI CMP is discussed. Directions for future work have been presented at the end of the thesis.

Programmable architecture for pixel level processing tasks in lightweight strapdown IR seekers

NASA Astrophysics Data System (ADS)

Coates, James L.

1993-06-01

Typical processing tasks associated with missile IR seeker applications are described, and a straw man suite of algorithms is presented. A fully programmable multiprocessor architecture is realized on a multimedia video processor (MVP) developed by Texas Instruments. The MVP combines the elements of RISC, floating point, advanced DSPs, graphics processors, display and acquisition control, RAM, and external memory. Front end pixel level tasks typical of missile interceptor applications, operating on 256 x 256 sensor imagery, can be processed at frame rates exceeding 100 Hz in a single MVP chip.

Optical interconnection networks for high-performance computing systems

NASA Astrophysics Data System (ADS)

Biberman, Aleksandr; Bergman, Keren

2012-04-01

Enabled by silicon photonic technology, optical interconnection networks have the potential to be a key disruptive technology in computing and communication industries. The enduring pursuit of performance gains in computing, combined with stringent power constraints, has fostered the ever-growing computational parallelism associated with chip multiprocessors, memory systems, high-performance computing systems and data centers. Sustaining these parallelism growths introduces unique challenges for on- and off-chip communications, shifting the focus toward novel and fundamentally different communication approaches. Chip-scale photonic interconnection networks, enabled by high-performance silicon photonic devices, offer unprecedented bandwidth scalability with reduced power consumption. We demonstrate that the silicon photonic platforms have already produced all the high-performance photonic devices required to realize these types of networks. Through extensive empirical characterization in much of our work, we demonstrate such feasibility of waveguides, modulators, switches and photodetectors. We also demonstrate systems that simultaneously combine many functionalities to achieve more complex building blocks. We propose novel silicon photonic devices, subsystems, network topologies and architectures to enable unprecedented performance of these photonic interconnection networks. Furthermore, the advantages of photonic interconnection networks extend far beyond the chip, offering advanced communication environments for memory systems, high-performance computing systems, and data centers.

A parallel row-based algorithm with error control for standard-cell replacement on a hypercube multiprocessor

NASA Technical Reports Server (NTRS)

Sargent, Jeff Scott

1988-01-01

A new row-based parallel algorithm for standard-cell placement targeted for execution on a hypercube multiprocessor is presented. Key features of this implementation include a dynamic simulated-annealing schedule, row-partitioning of the VLSI chip image, and two novel new approaches to controlling error in parallel cell-placement algorithms; Heuristic Cell-Coloring and Adaptive (Parallel Move) Sequence Control. Heuristic Cell-Coloring identifies sets of noninteracting cells that can be moved repeatedly, and in parallel, with no buildup of error in the placement cost. Adaptive Sequence Control allows multiple parallel cell moves to take place between global cell-position updates. This feedback mechanism is based on an error bound derived analytically from the traditional annealing move-acceptance profile. Placement results are presented for real industry circuits and the performance is summarized of an implementation on the Intel iPSC/2 Hypercube. The runtime of this algorithm is 5 to 16 times faster than a previous program developed for the Hypercube, while producing equivalent quality placement. An integrated place and route program for the Intel iPSC/2 Hypercube is currently being developed.

Affinity chromatography matrices for depletion and purification of casein glycomacropeptide from bovine whey.

PubMed

Baieli, María F; Urtasun, Nicolás; Martinez, María J; Hirsch, Daniela B; Pilosof, Ana M R; Miranda, María V; Cascone, Osvaldo; Wolman, Federico J

2017-01-01

Casein glycomacropeptide (CMP) is a 64- amino acid peptide found in cheese whey, which is released after κ-casein specific cleavage by chymosin. CMP lacks aromatic amino acids, a characteristic that makes it usable as a nutritional supplement for people with phenylketonuria. CMP consists of two nonglycosylated isoforms (aCMP A and aCMP B) and its different glycosylated forms (gCMP A and gCMP B). The most predominant carbohydrate of gCMP is N-acetylneuraminic acid (sialic acid). Here, we developed a CMP purification process based on the affinity of sialic acid for wheat germ agglutinin (WGA). After formation of chitosan beads and adsorption of WGA, the agglutinin was covalently attached with glutaraldehyde. Two matrices with different WGA density were assayed for CMP adsorption. Maximum adsorption capacities were calculated according to the Langmuir model from adsorption isotherms developed at pH 7.0, being 137.0 mg/g for the matrix with the best performance. In CMP reduction from whey, maximum removal percentage was 79% (specifically 33.7% of gCMP A and B, 75.8% of aCMP A, and 93.9% of aCMP B). The CMP was recovered as an aggregate with an overall yield of 64%. Therefore, the matrices developed are promising for CMP purification from cheese whey. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 33:171-180, 2017. © 2016 American Institute of Chemical Engineers.

Gene Expression and Pathway Analysis of Effects of the CMAH Deactivation on Mouse Lung, Kidney and Heart

PubMed Central

Kwon, Deug-Nam; Chang, Byung-Soo; Kim, Jin-Hoi

2014-01-01

Background N-glycolylneuraminic acid (Neu5Gc) is generated by hydroxylation of CMP-Neu5Ac to CMP-Neu5Gc, catalyzed by CMP-Neu5Ac hydroxylase (CMAH). However, humans lack this common mammalian cell surface molecule, Neu5Gc, due to inactivation of the CMAH gene during evolution. CMAH is one of several human-specific genes whose function has been lost by disruption or deletion of the coding frame. It has been suggested that CMAH inactivation has resulted in biochemical or physiological characteristics that have resulted in human-specific diseases. Methodology/Principal Findings To identify differential gene expression profiles associated with the loss of Neu5Gc expression, we performed microarray analysis using Illumina MouseRef-8 v2 Expression BeadChip, using the main tissues (lung, kidney, and heart) from control mice and CMP-Neu5Ac hydroxylase (Cmah) gene knock-out mice, respectively. Out of a total of 25,697 genes, 204, 162, and 147 genes were found to be significantly modulated in the lung, kidney, and heart tissues of the Cmah null mouse, respectively. In this study, we examined the gene expression profiles, using three commercial pathway analysis software packages: Ingenuity Pathways Analysis, Kyoto Encyclopedia of Genes and Genomes analysis, and Pathway Studio. The gene ontology analysis revealed that the top 6 biological processes of these genes included protein metabolism and modification, signal transduction, lipid, fatty acid, and steroid metabolism, nucleoside, nucleotide and nucleic acid metabolism, immunity and defense, and carbohydrate metabolism. Gene interaction network analysis showed a common network that was common to the different tissues of the Cmah null mouse. However, the expression of most sialytransferase mRNAs of Hanganutziu-Deicher antigen, sialy-Tn antigen, Forssman antigen, and Tn antigen was significantly down-regulated in the liver tissue of Cmah null mice. Conclusions/Significance Mice bearing a human-like deletion of the Cmah gene serve as an important model for the study of abnormal pathogenesis and/or metabolism caused by the evolutionary loss of Neu5Gc synthesis in humans. PMID:25229777

Self-assembled nanocomplexes of anionic pullulan and polyallylamine for DNA and pH-sensitive intracellular drug delivery

NASA Astrophysics Data System (ADS)

Vora, Lalit; Tyagi, Monica; Patel, Ketan; Gupta, Sanjay; Vavia, Pradeep

2014-12-01

The amalgamation of chemotherapy and gene therapy is promising treatment option for cancer. In this study, novel biocompatible self-assembled nanocomplexes (NCs) between carboxylmethylated pullulan t335 (CMP) with polyallylamine (CMP-PAA NCs) were developed for plasmid DNA (pDNA) and pH-sensitive doxorubicin (DOX) delivery. DOX was conjugated to CMP (DOX-CMP) via hydrazone and confirmed by FTIR and 1H-NMR. In vitro release studies of pH-sensitive DOX-CMP conjugate showed 23 and 85 % release after 48 h at pH 7.4 (physiological pH) and pH 5 (intracellular/tumoral pH), respectively. The CMP-PAA NCs or DOX-CMP-PAA NCs self-assembled into a nanosized (<250 nm) spherical shape as confirmed by DLS and TEM. The hemolysis and cytotoxicity study indicated that the CMP-PAA NCs did not show cytotoxicity in comparison with plain polyallylamine. Gel retardation assay showed complete binding of pDNA with CMP-PAA NCs at 1:2 weight ratio. CMP-PAA NCs/pDNA showed significantly higher transfection in HEK293 cells compared to PAA/pDNA complexes. Confocal imaging demonstrated successful cellular uptake of DOX-CMP-PAA NCs in HEK293 cells. Thus, NCs hold great potential for targeted pDNA and pH-sensitive intratumoral drug delivery.

Cell-derived microparticles and vascular pregnancy complications: a systematic and comprehensive review.

PubMed

Alijotas-Reig, Jaume; Palacio-Garcia, Carles; Llurba, Elisa; Vilardell-Tarres, Miquel

2013-02-01

To assess current studies on the relationship between cell-derived microparticles (cMP) and recurrent miscarriages (RM) and pre-eclampsia (PE), and review the relationships between cMP and inflammatory and clot pathways, antiphospholipid antibodies (aPL), cytokines, and pregnancy complications. Systematic and comprehensive review of the literature from January 2000 to January 2012. Vall d'Hebron University Hospital. Women with recurrent miscarriages or PE, healthy nonpregnant women, and healthy pregnant women. None. Comparison of cMP numbers and types among groups. Platelet and endothelial cMP are increased in women with normal pregnancies compared with nonpregnant healthy women. Only five case-control studies regarding cMP and RM and 16 on cMP and PE were found to match our objective. Three of five articles referring to RM showed differences in cMP numbering, and 13 of 16 on cMP and PE showed differences in some type of cMP compared with controls. Cell-derived microparticles were raised in normal pregnancy. Recurrent miscarriage seems to be related to endothelial and platelet cell activation and/or consumption. An increase in almost all cMP types was observed in PE. A relationship between cMP and endothelial activation and proinflammatory status seems to exist. Copyright © 2013 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Comorbidity of fibromyalgia and cervical myofascial pain syndrome.

PubMed

Cakit, Burcu Duyur; Taskin, Suhan; Nacir, Baris; Unlu, Irem; Genc, Hakan; Erdem, Hatice Rana

2010-04-01

The aims of this study are to determine the frequency of fibromyalgia syndrome (FMS) in patients with chronic cervical myofascial pain (CMP) and to investigate the FMS characteristics in CMP patients. Ninty-three patients with CMP and 30 age-matched healthy women were included in this study. Main outcome measures included visual analog scale (VAS), Beck Depression Inventory (BDI), and pain pressure thresholds. CMP patients were evaluated for the existence of FMS. The severity of FMS was assessed with total myalgic score (TMS) and control point score (CPS). Most common clinical characteristics of FMS were noted. Of the 93 CMP subjects, 22 (23.6%) patients fulfilled the classification criteria for FMS. Number of tender points were higher (p=0.0), while TMS (p=0.0) and CPS (p=0.0) values were lower in comorbid CMP and FMS patients than regional CMP group. There were statistically significant differences between regional CMP patients and comorbid CMP and FMS patients regarding presence of fatigue (p=0.0) and irritable bowel syndrome (p=0.022). There was no statistically significant difference between patient groups regarding VAS values (p>0.05). BDI values of the regional CMP were significantly lower than comorbid CMP and FMS patients (p=0.011). In conclusion, we found that nearly a quarter of CMP patients were comorbid with FMS, and psychological and comorbid symptoms were more prominent in comorbid patients. We thought that, these two syndromes might be overlapping conditions and as a peripheral pain generator or inducer of central sensitisation, MPS might lead to FMS or precipitate and worsen the FMS symptoms.

SCAMPI Lead Appraiser (Service Mark) Body of Knowledge (SLA BOK)

DTIC Science & Technology

2007-10-01

CMP 6.4.2, Understanding business goals and concerns as they impact process judgments • CMP 6.5.4, Recommending next steps for process improvement...Applying practice characterization and rating rules CMP 6.4.2 Understanding business goals and concerns as they impact process judgments Associated...judgments CMP 6.4.2* Understanding business goals and concerns as they impact process judgments CMP 6.4.3 Conducting preliminary findings

Vascular delay of the latissimus dorsi muscle: an essential component of cardiomyoplasty.

PubMed

Carroll, S M; Carroll, C M; Stremel, R W; Heilman, S J; Tobin, G R; Barker, J H

1997-04-01

Cardiomyoplasty (CMP) uses the latissimus dorsi muscle (LDM) to assist the heart in cases of cardiac failure. Distal ischemia and necrosis of the LDM is a recognized complication of CMP that can reduce distal muscle function and the mechanical effectiveness of CMP. Canine (n = 9) LDMs were subjected to a 10-day period of vascular delay followed by a simulated CMP. Two weeks after simulated CMP (corresponding to the healing delay between CMP and the onset of LDM stimulation used in the clinical setting), LDM perfusion was measured in the distal, middle, and proximal segments of the muscle, and circumferential (distal and middle squeezing muscle function) and longitudinal (proximal pulling muscle function) force generation and fatigue rates were measured. The results were compared with the contralateral nondelayed simulated CMP. Muscle perfusion was significantly (p < 0.05) greater in the distal and middle segments of vascular-delayed LDMs. Circumferential muscle force generation and fatigue rates were significantly (p < 0.05) improved in the vascular-delayed LDMs. Vascular delay can significantly improve LDM perfusion and function in a model that closely reflects clinical CMP, and the use of vascular delay may improve clinical outcomes in CMP.

A novel approach of chemical mechanical polishing using environment-friendly slurry for mercury cadmium telluride semiconductors

PubMed Central

Zhang, Zhenyu; Wang, Bo; Zhou, Ping; Guo, Dongming; Kang, Renke; Zhang, Bi

2016-01-01

A novel approach of chemical mechanical polishing (CMP) is developed for mercury cadmium telluride (HgCdTe or MCT) semiconductors. Firstly, fixed-abrasive lapping is used to machine the MCT wafers, and the lapping solution is deionized water. Secondly, the MCT wafers are polished using the developed CMP slurry. The CMP slurry consists of mainly SiO2 nanospheres, H2O2, and malic and citric acids, which are different from previous CMP slurries, in which corrosive and toxic chemical reagents are usually employed. Finally, the polished MCT wafers are cleaned and dried by deionized water and compressed air, respectively. The novel approach of CMP is environment-friendly. Surface roughness Ra, and peak-to-valley (PV) values of 0.45, and 4.74 nm are achieved, respectively on MCT wafers after CMP. The first and second passivating processes are observed in electrochemical measurements on MCT wafers. The fundamental mechanisms of CMP are proposed according to the X-ray photoelectron spectroscopy (XPS) and electrochemical measurements. Malic and citric acids dominate the first passivating process, and the CMP slurry governs the second process. Te4+3d peaks are absent after CMP induced by the developed CMP slurry, indicating the removing of oxidized films on MCT wafers, which is difficult to achieve using single H2O2 and malic and citric acids solutions. PMID:26926622

42 CFR 417.407 - Requirements for a Competitive Medical Plan (CMP).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 3 2010-10-01 2010-10-01 false Requirements for a Competitive Medical Plan (CMP... AND HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE MEDICAL... Requirements for a Competitive Medical Plan (CMP). (a) General rule. To qualify as a CMP, an entity must be...

42 CFR 417.407 - Requirements for a Competitive Medical Plan (CMP).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 3 2011-10-01 2011-10-01 false Requirements for a Competitive Medical Plan (CMP... AND HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE MEDICAL... Requirements for a Competitive Medical Plan (CMP). (a) General rule. To qualify as a CMP, an entity must be...

SEMICONDUCTOR TECHNOLOGY A signal processing method for the friction-based endpoint detection system of a CMP process

NASA Astrophysics Data System (ADS)

Chi, Xu; Dongming, Guo; Zhuji, Jin; Renke, Kang

2010-12-01

A signal processing method for the friction-based endpoint detection system of a chemical mechanical polishing (CMP) process is presented. The signal process method uses the wavelet threshold denoising method to reduce the noise contained in the measured original signal, extracts the Kalman filter innovation from the denoised signal as the feature signal, and judges the CMP endpoint based on the feature of the Kalman filter innovation sequence during the CMP process. Applying the signal processing method, the endpoint detection experiments of the Cu CMP process were carried out. The results show that the signal processing method can judge the endpoint of the Cu CMP process.

Embedded Multiprocessor Technology for VHSIC Insertion

NASA Technical Reports Server (NTRS)

Hayes, Paul J.

1990-01-01

Viewgraphs on embedded multiprocessor technology for VHSIC insertion are presented. The objective was to develop multiprocessor system technology providing user-selectable fault tolerance, increased throughput, and ease of application representation for concurrent operation. The approach was to develop graph management mapping theory for proper performance, model multiprocessor performance, and demonstrate performance in selected hardware systems.

A novel protein from edible fungi Cordyceps militaris that induces apoptosis.

PubMed

Bai, Ke-Chun; Sheu, Fuu

2018-01-01

Cordyceps militaris is a dietary therapeutic fungus that is an important model species in Cordyceps research. In this study, we purified a novel protein from the fruit bodies of C. militaris and designated it as Cordyceps militaris protein (CMP). CMP has a molecular mass of 18.0 kDa and is not glycosylated. Interestingly, CMP inhibited cell viability in murine primary cells and other cell lines in a time- and dose-dependent manner. Using trypan blue staining and a lactate dehydrogenase release assay, we showed that CMP caused cell death in the murine hepatoma cell line BNL 1MEA.7R.1. Furthermore, the frequency of BNL 1MEA.7R.1 cells at the sub-G1 stage was increased by CMP. Apoptosis, as determined by Annexin V and propidium iodide analysis, indicated that CMP could mediate BNL 1MEA.7R.1 apoptosis, but not necrosis. After coincubation with CMP, a decrease in mitochondria potential was detected using 3,3'-dihexyloxacarbocyanine iodide. These results suggest that CMP is a harmful protein that induces apoptosis through a mitochondrion-dependent pathway. Stability experiments demonstrated that heat treatment and alkalization degraded CMP and further destroyed its cell-death-inducing ability, implying that cooking is necessary for food containing C. militaris. Copyright © 2017. Published by Elsevier B.V.

Mechanism of inhibition of mammalian tumor and other thymidylate synthases by N sup 4 -hydroxy-dCMP, N sup 4 -hydroxy-5-fluoro-dCMP, and related analogues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rode, W.; Zielinski, Z.; Dzik, J.M.

1990-12-01

N{sup 4}-Hydroxy-dCMP (N{sup 4}-OH-dCMP), N{sup 4}-methoxy-dCMP (N{sup 4}-OMe-dCMP), and their 5-fluoro congeners were all slow-binding inhibitors of Ehrlich carcinoma thymidylate synthase (TS), competitive with respect to dUMP, and had differing kinetic constants describing interactions with the two TS binding sites. N{sup 4}-OH-dCMP was not a substrate and its inactivation of TS was methylenetetrahydrofolate-dependent, hence mechanism-based. K{sub i} values for N{sup 4}-OH-dCMP and its 5-fluoro analogue were in the range 10{sup {minus}7}-10{sup {minus}8} M, 2-3 orders of magnitude higher for the corresponding N{sup 4}-OMe analogues. The 5-methyl analogue of N{sup 4}-OHdCMP was 10{sup 4}-fold less potent, pointing to the anti rotamermore » of the imino form of exocyclic N{sup 4}-OH, relative to the ring N(3), as the active species. This is consistent with weaker slow-binding inhibition of the altered enzyme from 5-FdUrd-resistant, relative to parent, L1210 cells by both FdUMP and N{sup 4}-OH-dCMP, suggesting interaction of both N{sup 4}-OH and C(5)-F groups with the same region of the active center. Kinetic studies with purified enzyme from five sources, viz., Ehrlich carcinoma, L1210 parental, and 5-FdUrd-resistant cells, regenerating rat liver, and the tapeworm Hymenolepis diminuta, demonstrated that addition of a 5-fluoro substituent to N{sup 4}-OH-dCMP increased its affinity from 2- to 20-fold for the enzyme from different sources. With the Ehrlich and tapeworm enzymes, N{sup 4}-OH-FdCMP and FdUMP were almost equally effective inhibitors.« less

Reversible Sialylation: Synthesis of CMP-NeuAc from 5′-CMP using α2,3-sialyl O-glycan, glycolipid and macromolecule based donors allow for the synthesis of diverse sialylated products

PubMed Central

Chandrasekaran, E.V.; Xue, Jun; Xia, Jie; Locke, Robert D.; Matta, Khushi L.; Neelamegham, Sriram

2008-01-01

Sialyltransferases transfer sialic acid from CMP-NeuAc to an acceptor molecule. Trans-sialidases of parasites transfer α2,3 linked sialic acid from one molecule to another without the involvement of CMP-NeuAc. Here, we report another type of sialylation termed reverse sialylation catalyzed by mammalian sialyltransferase ST3Gal-II. This enzyme synthesizes CMP-NeuAc by transferring NeuAc from the NeuAcα2,3Galβ1,3GalNAcα-unit of O-glycans, 3-sialyl globo unit of glycolipids and sialylated macromolecules to 5′-CMP. CMP-NeuAc produced in situ is utilized by the same enzyme to sialylate other O-glycans and by other sialyltransferases such as ST6Gal-I and ST6GalNAc-I forming α2,6 sialylated compounds. ST3Gal-II also catalyzed the conversion of 5′-UMP to UMP-NeuAc, which was found to be an inactive sialyl donor. Reverse sialylation proceeded without the need for free sialic acid, divalent metal ions or energy. The direct sialylation using CMP-NeuAc as well as the formation of CMP-NeuAc from 5′-CMP had a wide optimum range (pH 5.2–7.2 and 4.8–6.4 respectively) whereas the entire reaction comprising in situ production of CMP-NeuAc and sialylation of acceptor had a sharp optimum at pH 5.6 (the activity level 50% at pH 5.2 & 6.8 and 25% at pH 4.8 & 7.2). Several properties distinguish forward/conventional vs. reverse sialylation: i. Sodium citrate inhibited forward sialylation but not reverse sialylation. ii. 5′-CDP, a potent forward sialyltransferase inhibitor, did not inhibit the conversion of 5′-CMP to CMP-NeuAc. iii. The mucin core 2 compound 3-O-sulfoα2,3Galβ1,4GlcNAcβ1,6(Galβ1,3)GalNAcα-O-Bn, an efficient acceptor for ST3Gal-II, inhibited the conversion of 5′-CMP to CMP-NeuAc. A significant level of reverse sialylation activity is noted in human prostate cancer cell lines LNCaP and PC3. Overall, the study demonstrates that the sialyltransferase reaction is readily reversible in the case of ST3Gal-II and can be exploited for the enzymatic synthesis of diverse sialyl products. PMID:18067323

Fate of 1-(1',4'-cyclohexadienyl)-2-methylaminopropane (CMP) in soil: route-specific by-product in the clandestine manufacture of methamphetamine.

PubMed

Pal, Raktim; Megharaj, Mallavarapu; Kirkbride, K Paul; Naidu, Ravi

2012-02-01

We investigated the fate of 1-(1',4'-cyclohexadienyl)-2-methylaminopropane (CMP) in soil. CMP is the major route-specific byproduct in the clandestine manufacture of methamphetamine (MAP) by the use of excess alkali metal (e.g., lithium) in liquid ammonia, which is commonly referred to as the "Nazi method". This is one of the most common methods used in many countries for the illicit production of MAP. Knowledge on the fate of CMP in the terrestrial environment is essential to combat potential threats arising from illegal dumping of clandestine laboratory wastes. We report on the sorption-desorption, degradation, and metabolism patterns of CMP in three South Australian soils investigated in laboratory scale. CMP sorption in the test soils followed a Freundlich isotherm in the concentration range of 5 to 100μgmL(-1). Degradation studies showed that CMP was fairly unstable in both non-sterile and sterile soils, with half-life values typically less than one week. The role of biotic and abiotic soil processes in the degradation of CMP also varied significantly between the different soils, and with the length of the incubation period. Interestingly, but not surprisingly, the results showed that the CMP was not actually degraded to any simpler compounds but transformed to more persistent MAP. Thus, the main concern with Nazi method is the potential hazard from MAP rather than CMP if wastes are disposed of into the environment. Copyright © 2011 Elsevier B.V. All rights reserved.

The study on the effect of pattern density distribution on the STI CMP process

NASA Astrophysics Data System (ADS)

Sub, Yoon Myung; Hian, Bernard Yap Tzen; Fong, Lee It; Anak, Philip Menit; Minhar, Ariffin Bin; Wui, Tan Kim; Kim, Melvin Phua Twang; Jin, Looi Hui; Min, Foo Thai

2017-08-01

The effects of pattern density on CMP characteristics were investigated using specially designed wafer for the characterization of pattern-dependencies in STI CMP [1]. The purpose of this study is to investigate the planarization behavior based on a direct STI CMP used in cerium (CeO2) based slurry system in terms of pattern density variation. The minimal design rule (DR) of 180nm generation technology node was adopted for the mask layout. The mask was successfully applied for evaluation of a cerium (CeO2) abrasive based direct STI CMP process. In this study, we described a planarization behavior of the loading-effects of pattern density variation which were characterized with layout pattern density and pitch variations using masks mentioned above. Furthermore, the characterizing pattern dependent on the variations of the dimensions and spacing features, in thickness remaining after CMP, were analyzed and evaluated. The goal was to establish a concept of library method which will be used to generate design rules reducing the probability of CMP-related failures. Details of the characterization were measured in various layouts showing different pattern density ranges and the effects of pattern density on STI CMP has been discussed in this paper.

Validation of multiprocessor systems

NASA Technical Reports Server (NTRS)

Siewiorek, D. P.; Segall, Z.; Kong, T.

1982-01-01

Experiments that can be used to validate fault free performance of multiprocessor systems in aerospace systems integrating flight controls and avionics are discussed. Engineering prototypes for two fault tolerant multiprocessors are tested.

[Features of Clinical Register of Chinese Medicine and Pharmacy Based on ClinicalTrials.gov. (USA)].

PubMed

Lu, Peng-fei; Liao, Xing; Xie, Yan-ming; Wang, Zhi-guo

2015-11-01

In recent 10 years, clinical trials of Chinese medicine and pharmacy (cMP) at clinicalTrials.gov.(USA) are gradually increasing. In order to analyze features of CMP clinical register, ClinicalTrials.gov register database were comprehensively retrieved in this study. Included clinical trials were input one item after another using EXCEL. A final of 348 CMP clinical trials were included. Results showed that China occupied the first place in CMP clinical register, followed by USA. CMP clinical trials, sponsored mainly by colleges/universities and hospitals, mostly covered interventional studies on evaluating safety/effectiveness of CMP. The proportions of studies, sponsored by mainland China and companies, recruitment trials and multi-center clinical trials in interventional trials were increasing. The proportions of studies sponsored by Hong Kong and Taiwan, research completed trials, unclear research status, phase III clinical trials, and published research trials in interventional trials were decreasing. Published ratios of CMP clinical trials were quite low. There were more missing types and higher proportions in trial register information.

Musculoskeletal pain in patients with chronic kidney disease.

PubMed

Caravaca, Francisco; Gonzales, Boris; Bayo, Miguel Ángel; Luna, Enrique

2016-01-01

Chronic musculoskeletal pain (CMP) is a very common symptom in patients with chronic kidney disease (CKD), and is associated with a significant deterioration in quality of life. To determine the prevalence and clinical characteristics associated with CMP in patients with advanced CKD not on dialysis, and to analyse their relation with other uraemic symptoms and their prognosis significance. Cross-sectional study to analyse the uraemic symptoms of an unselected cohort of patients with CKD stage 4-5 pre-dialysis. In order to characterise patients with CMP, demographic and anthropometric data were collected, as well as data on comorbidities and kidney function. In addition, inflammatory parameters, uric parameters, bone mineral metabolism including 25-hydroxycholecalciferol (25-OHCC), creatine kinase and drugs of potential interest including allopurinol, statins and erythropoiesis-stimulating agents were recorded. The study group consisted of 1169 patients (mean age 65±15 years, 54% male). A total of 38% of patients complained of CMP, and this symptom was more prevalent in women than in men (49 vs. 28%; P<.0001). Muscle weakness, pruritus, muscle cramps, ecchymosis, insomnia, oedema and dyspnoea were the most common symptoms associated with CMP. There were no significant associations between serum levels of creatine kinase, 25-OHCC, treatment with allopurinol, statins or erythropoiesis-stimulating agents and CMP. The female gender, elderly age, obesity, comorbidity (mainly diabetes, heart failure or COPD), and elevated levels of inflammatory markers (C-reactive protein and non-neutrophilic leukocytes) were the best determinants of CMP. While patients with CMP showed a worse survival rate, a multivariate analysis adjusted for demographic data ruled out the independent association of CMP with mortality. CMP is highly prevalent in patients with advanced CKD and is associated with other common symptoms of chronic uraemia. As with the general population, elderly age, the female gender, obesity and some comorbid conditions are the best determinants of CMP. Increased inflammatory markers commonly observed in patients with CMP may have a relevant role in its pathogenesis. Copyright © 2016 Sociedad Española de Nefrología. Published by Elsevier España, S.L.U. All rights reserved.

IgG subclass reactivity to human cardiac myosin in cardiomyopathy patients is indicative of a Th1-like autoimmune disease

PubMed Central

Skyllouriotis, P; Skyllouriotis-Lazarou, M; Natter, S; Steiner, R; Spitzauer, S; Kapiotis, S; Valent, P; Hirschl, A M; Guber, S E; Laufer, G; Wollenek, G; Wolner, E; Wimmer, M; Valenta, R

1999-01-01

Studies performed in mice together with the demonstration of increased levels of heart-specific autoantibodies, cytokines and cytokine receptors in sera from cardiomyopathy (CMP) patients argued for a pathogenic role of autoimmune mechanisms in CMP. This study was designed to analyse the presence of IgG anti-heart antibodies in sera from patients suffering from hypertrophic and dilatative forms of CMP as well as from patients with ischaemic heart disease and healthy individuals. Patients' sera were analysed for IgG reactivity to Western-blotted extracts prepared from human epithelial and endothelial cells, heart and skeletal muscle specimens as well as from Streptococcus pyogenes. The IgG subclass (IgG1–4) reactivity to purified human cardiac myosin was analysed by ELISA. While sera from CMP patients and healthy individuals displayed comparable IgG reactivity to a variety of human proteins, cardiac myosin represented the prominent antigen detected strongly and preferentially by sera from CMP patients. Pronounced IgG anti-cardiac myosin reactivity was frequently found in sera from patients with dilatative CMP and reduced ventricular function. ELISA analyses revealed a prominent IgG2/IgG3 anti-cardiac myosin reactivity in CMP sera, indicating a preferential Th1-like immune response. Elevated anti-cytomegalovirus, anti-enterovirus IgG titres as well as IgG reactivity to nitrocellulose-blotted S. pyogenes proteins were also frequently observed in the group of CMP patients. If further work can support the hypothesis that autoreactivity to cardiac myosin represents a pathogenic factor in CMP, specific immunomodulation of this Th1- towards a Th2-like immune response may represent a promising therapeutic strategy for CMP. PMID:9933448

Programmable partitioning for high-performance coherence domains in a multiprocessor system

DOEpatents

Blumrich, Matthias A [Ridgefield, CT; Salapura, Valentina [Chappaqua, NY

2011-01-25

A multiprocessor computing system and a method of logically partitioning a multiprocessor computing system are disclosed. The multiprocessor computing system comprises a multitude of processing units, and a multitude of snoop units. Each of the processing units includes a local cache, and the snoop units are provided for supporting cache coherency in the multiprocessor system. Each of the snoop units is connected to a respective one of the processing units and to all of the other snoop units. The multiprocessor computing system further includes a partitioning system for using the snoop units to partition the multitude of processing units into a plurality of independent, memory-consistent, adjustable-size processing groups. Preferably, when the processor units are partitioned into these processing groups, the partitioning system also configures the snoop units to maintain cache coherency within each of said groups.

Queueing analysis of a canonical model of real-time multiprocessors

NASA Technical Reports Server (NTRS)

Krishna, C. M.; Shin, K. G.

1983-01-01

A logical classification of multiprocessor structures from the point of view of control applications is presented. A computation of the response time distribution for a canonical model of a real time multiprocessor is presented. The multiprocessor is approximated by a blocking model. Two separate models are derived: one created from the system's point of view, and the other from the point of view of an incoming task.

A simple modern correctness condition for a space-based high-performance multiprocessor

NASA Technical Reports Server (NTRS)

Probst, David K.; Li, Hon F.

1992-01-01

A number of U.S. national programs, including space-based detection of ballistic missile launches, envisage putting significant computing power into space. Given sufficient progress in low-power VLSI, multichip-module packaging and liquid-cooling technologies, we will see design of high-performance multiprocessors for individual satellites. In very high speed implementations, performance depends critically on tolerating large latencies in interprocessor communication; without latency tolerance, performance is limited by the vastly differing time scales in processor and data-memory modules, including interconnect times. The modern approach to tolerating remote-communication cost in scalable, shared-memory multiprocessors is to use a multithreaded architecture, and alter the semantics of shared memory slightly, at the price of forcing the programmer either to reason about program correctness in a relaxed consistency model or to agree to program in a constrained style. The literature on multiprocessor correctness conditions has become increasingly complex, and sometimes confusing, which may hinder its practical application. We propose a simple modern correctness condition for a high-performance, shared-memory multiprocessor; the correctness condition is based on a simple interface between the multiprocessor architecture and a high-performance, shared-memory multiprocessor; the correctness condition is based on a simple interface between the multiprocessor architecture and the parallel programming system.

A conserved OmpA-like protein in Legionella pneumophila required for efficient intracellular replication.

PubMed

Goodwin, Ian P; Kumova, Ogan K; Ninio, Shira

2016-08-01

The OmpA-like protein domain has been associated with peptidoglycan-binding proteins, and is often found in virulence factors of bacterial pathogens. The intracellular pathogen Legionella pneumophila encodes for six proteins that contain the OmpA-like domain, among them the highly conserved uncharacterized protein we named CmpA. Here we set out to characterize the CmpA protein and determine its contribution to intracellular survival of L. pneumophila Secondary structure analysis suggests that CmpA is an inner membrane protein with a peptidoglycan-binding domain at the C-teminus. A cmpA mutant was able to replicate normally in broth, but failed to compete with an isogenic wild-type strain in an intracellular growth competition assay. The cmpA mutant also displayed significant intracellular growth defects in both the protozoan host Acanthamoeba castellanii and in primary bone marrow-derived macrophages, where uptake into the cells was also impaired. The cmpA phenotypes were completely restored upon expression of CmpA in trans The data presented here establish CmpA as a novel virulence factor of L. pneumophila that is required for efficient intracellular replication in both mammalian and protozoan hosts. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Polymer microfluidic device replacing fluids using only capillary force

NASA Astrophysics Data System (ADS)

Chung, Kwang Hyo; Lee, Dae Sik; Yang, Haesik; Kim, Sung Jin; Pyo, Hyun Bong

2005-02-01

A novel polymer microfluidic device for self-wash using only capillary force is presented. A liquid filled in a reaction chamber is replaced by another liquid with no external actuation. All the fluidic actuations in the device is pre-programmed about time and sequence, and accomplished by capillary force naturally. Careful design is necessary for exact actions. The fluidic conduits were designed by the newly derived theoretical equations about the capillary stop pressure and flow time. Simulations using CFD-ACE+ were conducted to check the validity of theory and the performance of the chip. These analytic results were consistent with experimental ones. The chip was made of polymers for the purpose of single use and low price. It was fabricated by sealing the hot-embossed PMMA substrate with a PET film. For simpler fabrication, the chip was of a single height. The embossing master was produced from a nickel-electroplating on a SU8-patterned Ni-plate followed by CMP. The contact angles of liquids on substrates were manipulated through the mixing of surfactants, and the temporal variations were monitored for a more exact design. The real actuation steps in experiment revealed the stable performance of selfwash, and coincided well with the designed ones. The presented microfluidic method can be applicable to other LOCs of special purposes through simple modification. For example, array or serial types would be possible for multiple selfwashes.

Iterative algorithms for tridiagonal matrices on a WSI-multiprocessor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gajski, D.D.; Sameh, A.H.; Wisniewski, J.A.

1982-01-01

With the rapid advances in semiconductor technology, the construction of Wafer Scale Integration (WSI)-multiprocessors consisting of a large number of processors is now feasible. We illustrate the implementation of some basic linear algebra algorithms on such multiprocessors.

Electrochemical characterization of bulk and thin film copper in ammonia- and nitric acid-based slurries for chemical mechanical planarization of interconnects

NASA Astrophysics Data System (ADS)

Sainio, Carlyn Anne

Copper will be replacing aluminum as the interconnect material in silicon integrated circuits. Chemical mechanical planarization (CMP) in combination with an inlaid metal interconnection scheme has been utilized to pattern copper interconnects. The thesis describes an attempt to understand the electrochemistry of copper in slurries used for CMP. Steady-state electrochemical potential measurements, linear polarization resistance determinations, and potentiodynamic and potentiostatic polarization scans have been used in order to characterize the mechanism by which copper is removed during CMP. Electrochemical measurements were implemented on a rotating disk assembly to simulate conditions during CMP. Experiments were performed on both bulk copper samples and blanket copper thin films sputter deposited onto silicon wafers. Electrochemical potential measurements have been used in conjunction with potential-pH diagrams to determine the possible copper species which are stable during CMP. Electrochemical results were correlated to CMP experiments to determine slurry compositions with optimum potential-pH ranges for copper planarization. The results indicate that such studies present an opportunity to isolate the electrochemical and chemical effects from the mechanical effects in the CMP of metals and to determine the dependencies of each of these effects on the other. CMP of copper was controlled by the removal of native or non-native surface films. High CMP rates were achieved by matching the rates of film formation and copper and film dissolution. During CMP, surface films are abraded, allowing increased dissolution of copper until the surface film reforms. When the surface was indented by abrasive particles, the corrosion rate of the exposed copper increased by two orders of magnitude. Etchants (i.e. ammonia or nitric acid) were necessary for high CMP rates (120-240 nm/min) and to minimize scratching. CMP rates of copper in 1 volume percent NHsb4OH and 0.7 volume percent HNOsb3 with 0.0016 weight percent KMnOsb4 were comparable. Electrochemical characterization can narrow the possible slurry compositions that may be used for polishing. Also, the possibility of implementing electrochemical techniques to detect the endpoint of polishing was investigated. Although electrochemical measurements in ammonia-based slurries did not indicate when tantalum was exposed, similar measurements may be used to determine when polishing pads should be replaced.

Shared performance monitor in a multiprocessor system

DOEpatents

Chiu, George; Gara, Alan G; Salapura, Valentina

2014-12-02

A performance monitoring unit (PMU) and method for monitoring performance of events occurring in a multiprocessor system. The multiprocessor system comprises a plurality of processor devices units, each processor device for generating signals representing occurrences of events in the processor device, and, a single shared counter resource for performance monitoring. The performance monitor unit is shared by all processor cores in the multiprocessor system. The PMU is further programmed to monitor event signals issued from non-processor devices.

Cm-p5: an antifungal hydrophilic peptide derived from the coastal mollusk Cenchritis muricatus (Gastropoda: Littorinidae).

PubMed

López-Abarrategui, Carlos; McBeth, Christine; Mandal, Santi M; Sun, Zhenyu J; Heffron, Gregory; Alba-Menéndez, Annia; Migliolo, Ludovico; Reyes-Acosta, Osvaldo; García-Villarino, Mónica; Nolasco, Diego O; Falcão, Rosana; Cherobim, Mariana D; Dias, Simoni C; Brandt, Wolfgang; Wessjohann, Ludger; Starnbach, Michael; Franco, Octavio L; Otero-González, Anselmo J

2015-08-01

Antimicrobial peptides form part of the first line of defense against pathogens for many organisms. Current treatments for fungal infections are limited by drug toxicity and pathogen resistance. Cm-p5 (SRSELIVHQRLF), a peptide derived from the marine mollusk Cenchritis muricatus peptide Cm-p1, has a significantly increased fungistatic activity against pathogenic Candida albicans (minimal inhibitory concentration, 10 µg/ml; EC50, 1.146 µg/ml) while exhibiting low toxic effects against a cultured mammalian cell line. Cm-p5 as characterized by circular dichroism and nuclear magnetic resonance revealed an α-helical structure in membrane-mimetic conditions and a tendency to random coil folding in aqueous solutions. Additional studies modeling Cm-p5 binding to a phosphatidylserine bilayer in silico and isothermal titration calorimetry using lipid monophases demonstrated that Cm-p5 has a high affinity for the phospholipids of fungal membranes (phosphatidylserine and phosphatidylethanolamine), only moderate interactions with a mammalian membrane phospholipid, low interaction with ergosterol, and no interaction with chitin. Adhesion of Cm-p5 to living C. albicans cells was confirmed by fluorescence microscopy with FITC-labeled peptide. In a systemic candidiasis model in mice, intraperitoneal administration of Cm-p5 was unable to control the fungal kidney burden, although its low amphiphaticity could be modified to generate new derivatives with improved fungicidal activity and stability. © FASEB.

Synergistic effect of casein glycomacropeptide on sodium caseinate foaming properties.

PubMed

Morales, R; Martinez, M J; Pilosof, A M R

2017-11-01

Several strategies to improve the interfacial properties and foaming properties of proteins may be developed; among them, the use of mixtures of biopolymers that exhibit synergistic interactions. The aim of the present work was to evaluate the effect of casein glycomacropeptide (CMP) on foaming and surface properties of sodium caseinate (NaCas) and to establish the role of protein interactions in the aqueous phase. To this end particles size, interfacial and foaming properties of CMP, NaCas and NaCas-CMP mixtures at pH 5.5 and 7 were determined. At both pH, the interaction between CMP and NaCas induced a decrease in the aggregation state of NaCas. Single CMP foams showed the highest and NaCas the lowest foam overrun (FO) and the mixture exhibited intermediate values. CMP foam quickly drained. The drainage profile of mixed foams was closer to NaCas foams; at pH 5.5, mixed foams drained even slower than NaCas foam, exhibiting a synergistic performance. Additionally, a strong synergism was observed on the collapse of mixed foams at pH 5.5. Finally, a model to explain the synergistic effect observed on foaming properties in CMP-NaCas mixtures has been proposed; the reduced aggregation state of NaCas in the presence of CMP, made it more efficient for foam stabilization. Copyright © 2017 Elsevier B.V. All rights reserved.

A fault-tolerant multiprocessor architecture for aircraft, volume 1. [autopilot configuration

NASA Technical Reports Server (NTRS)

Smith, T. B.; Hopkins, A. L.; Taylor, W.; Ausrotas, R. A.; Lala, J. H.; Hanley, L. D.; Martin, J. H.

1978-01-01

A fault-tolerant multiprocessor architecture is reported. This architecture, together with a comprehensive information system architecture, has important potential for future aircraft applications. A preliminary definition and assessment of a suitable multiprocessor architecture for such applications is developed.

Use of a novel radiometric method to assess the inhibitory effect of donepezil on acetylcholinesterase activity in minimally diluted tissue samples

PubMed Central

Kikuchi, Tatsuya; Okamura, Toshimitsu; Arai, Takuya; Obata, Takayuki; Fukushi, Kiyoshi; Irie, Toshiaki; Shiraishi, Tetsuya

2010-01-01

Background and purpose: Cholinesterase inhibitors have been widely used for the treatment of patients with dementia. Monitoring of the cholinesterase activity in the blood is used as an indicator of the effect of the cholinesterase inhibitors in the brain. The selective measurement of cholinesterase with low tissue dilution is preferred for accurate monitoring; however, the methods have not been established. Here, we investigated the effect of tissue dilution on the action of cholinesterase inhibitors using a novel radiometric method with selective substrates, N-[14C]methylpiperidin-4-yl acetate ([14C]MP4A) and (R)-N-[14C]methylpiperidin-3-yl butyrate ([14C]MP3B_R), for AChE and butyrylcholinesterase (BChE) respectively. Experimental approach: We investigated the kinetics of hydrolysis of [14C]-MP4A and [14C]-MP3B_R by cholinesterases, and evaluated the selectivity of [14C]MP4A and [14C]MP3B_R for human AChE and BChE, respectively, compared with traditional substrates. Then, IC50 values of cholinesterase inhibitors in minimally diluted and highly diluted tissues were measured with [14C]MP4A and [14C]MP3B_R. Key results: AChE and BChE activities were selectively measured as the first-order hydrolysis rates of [14C]-MP4A and [14C]MP3B_R respectively. The AChE selectivity of [14C]MP4A was an order of magnitude higher than traditional substrates used for the AChE assay. The IC50 values of specific AChE and BChE inhibitors, donepezil and ethopropazine, in 1.2-fold diluted human whole blood were much higher than those in 120-fold diluted blood. In addition, the IC50 values of donepezil in monkey brain were dramatically decreased as the tissue was diluted. Conclusions and implications: This method would effectively monitor the activity of cholinesterase inhibitors used for therapeutics, pesticides and chemical warfare agents. PMID:20401964

Health fair screening: the clinical utility of the comprehensive metabolic profile.

PubMed

Alpert, Jeffrey P; Greiner, Allen; Hall, Sandra

2004-01-01

Health fairs are a common method used by providers and health care organizations to provide screening tests, including comprehensive metabolic profiles (CMPs), to asymptomatic individuals. No national organizations currently recommend the complete CMP as a screening test for asymptomatic individuals in primary care settings. This study evaluated the value of CMPs in a health fair setting by measuring the ability of a health fair CMP to predict new medical diagnoses among residents of a sparsely populated rural county. Volunteer participants submitted fasting blood samples at a health fair conducted by a county health center in a county with 2,531 total residents. CMP values were determined to be "normal" or "abnormal" based on laboratory reference ranges and clinical judgment of the health center physicians. Medical records were reviewed 4 months later to determine if participants with abnormal CMP values had been diagnosed with new medical conditions as a result of the screening tests. Analysis was conducted to evaluate CMP test characteristics and determine whether demographic factors or specific CMP values predicted new medical diagnoses in the participants. Out of 478 health fair participants, 73 individuals had at least one abnormal CMP value. The most frequently occurring abnormal value was an elevated glucose level, with Hispanic participants significantly more likely to have this abnormality than whites. After all evaluation was completed, only about 1% of tested subjects had a new diagnosis as a result of the screening CMP test; most abnormal CMP tests did not result in a new diagnosis. The positive predictive value for an abnormal test resulting in a new medical diagnosis was 0.356. Comprehensive metabolic profiles have limited value as a screening tool in asymptomatic populations at health fairs.

[Anti-tissue transglutaminase antibodies not related to gluten intake].

PubMed

Garcia-Peris, Mónica; Donat Aliaga, Ester; Roca Llorens, María; Masip Simó, Etna; Polo Miquel, Begoña; Ribes Koninckx, Carmen

2018-03-16

Anti-tissue transglutaminase antibodies (tTG) have high specificity for coeliac disease (CD). However, positive anti-tTG antibodies have been described in non-coeliac patients. Aim To assess positive anti-tTG antibodies not related to gluten intake. Retrospective review and follow up conducted on patients with suspected CD (increase anti-tTG levels and gastrointestinal symptoms) but with atypical serology results, positive anti-tTG with gluten free diet and a decrease in anti-tTG levels despite gluten intake. A total of 9 cases were reviewed in which 5 cases had Marsh 3 involvement in the initial biopsy, and were diagnosed with CD (Group A). They began a gluten free diet and also a cow's milk protein (CMP) free diet because of their nutritional status. When CMP was re-introduced, anti-tTG increased, and returned to normal after the CMP was withdrawn again. The other 4 patients had a normal initial biopsy (Group B). Gluten was not removed from their diet, but they started a CMP free diet because a non IgE mediated CMP allergy was suspected. Symptoms disappeared, and anti-tTG was normal after CMP free diet with gluten intake. All the patients had susceptibility haplotype HLA DQ2/DQ8. CMP ingestion after an exclusion diet can induce an increase in anti-tTG in some coeliac subjects. CMP can produce this immune response if there were no gluten transgressions. This response has also been observed in non-IgE mediated CMP allergy patients with the susceptibility haplotype HLA DQ2/DQ8. Copyright © 2018. Publicado por Elsevier España, S.L.U.

The cox-maze procedure for lone atrial fibrillation: a single-center experience over 2 decades.

PubMed

Weimar, Timo; Schena, Stefano; Bailey, Marci S; Maniar, Hersh S; Schuessler, Richard B; Cox, James L; Damiano, Ralph J

2012-02-01

The Cox-Maze procedure (CMP) has achieved high success rates in the therapy of atrial fibrillation (AF) while becoming progressively less invasive. This report evaluates our experience with the CMP in the treatment of lone AF over 2 decades and compares the original cut-and-sew CMP-III to the ablation-assisted CMP-IV, which uses bipolar radiofrequency and cryoenergy to create the original lesion pattern. Data were collected prospectively on 212 consecutive patients (mean age, 53.5±10.4 years; 78% male) who underwent a stand-alone CMP from 1992 through 2010. The median duration of preoperative AF was 6 (interquartile range, 2.9-11.5) years, with 48% paroxysmal and 52% persistent or long-standing persistent AF. Univariate analysis with preoperative and perioperative variables used as covariates for the CMP-III (n=112) and the CMP-IV (n=100) was performed. Overall, 30-day mortality was 1.4%, with no intraoperative deaths. Freedom from AF was 93%, and freedom from AF off antiarrhythmics was 82%, at a mean follow-up time of 3.6±3.1 years. Freedom from symptomatic AF at 10 years was 85%. Only 1 late stroke occurred, with 80% of patients not receiving anticoagulation therapy. The less invasive CMP-IV had significantly shorter cross-clamp times (41±13 versus 92±26 minutes; P<0.001) while achieving high success rates, with 90% freedom from AF and 84% freedom from AF off antiarrhythmics at 2 years. The CMP, although simplified and shortened by alternative energy sources, has excellent results, even with improved follow-up and stricter definition of failure.

United States Coast Guard Configuration Management Plan (CMP) for the Ports and Waterways Safety System (PAWSS) Project

DOT National Transportation Integrated Search

1997-01-01

Prepared ca. 1997. The Configuration Management Plan (CMP) provides configuration management instructions and guidance for the Vessel Traffic Service (VTS) system of the Ports and Waterways Safety System (PAWSS) project. The CMP describes in detail t...

The Structure of a Cyanobacterial Bicarbonate Transport Protein, CmpA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koropatkin, Nicole M.; Koppenaal, David W.; Pakrasi, Himadri B.

2007-01-26

Cyanobacteria, blue-green algae, are the most abundant autotrophs in aquatic environments and form the base of the food chain by fixing carbon and nitrogen into cellular biomass. To compensate for the low selectivity of Rubisco for CO₂ over O₂, Cyanobacteria have developed highly efficient CO₂concentrating machinery of which the ABC transport system CmpABCD from Synechocystis PCC 6803 is one component. Here we describe the structure of the bicarbonate binding protein, CmpA, in the absence and presence of bicarbonate and carbonic acid. CmpA is highly homologous to the nitrate transport protein, NrtA. CmpA binds carbonic acid at the entrance to themore » ligand-binding pocket whereas bicarbonate binds in nearly an identical location compared to nitrate binding to NrtA. Unexpectedly, bicarbonate binding is accompanied by a metal ion, identified as Ca²⁺ via inductively coupled plasma optical emission spectrometry. The binding of bicarbonate and metal is highly cooperative and suggests that CmpA co-transports bicarbonate and calcium.« less

Cystic meconium peritonitis with jejunoileal atresia: Is it associated with unfavorable outcome?

PubMed Central

Chan, Kin Wai Edwin; Lee, Kim Hung; Wong, Hei Yi Vicky; Tsui, Siu Yan Bess; Wong, Yuen Shan; Pang, Kit Yi Kristine; Mou, Jennifer Wai Cheung; Tam, Yuk Him

2017-01-01

AIM To compare the outcome between patients with jejunoileal atresia (JIA) associated with cystic meconium peritonitis (CMP) and patients with isolated JIA (JIA without CMP). METHODS A retrospective study was conducted for all neonates with JIA operated in our institute from January 2005 to January 2016. Demographics including the gestation age, sex, birth weight, age at operation, the presence of associated syndrome was recorded. Clinical outcome including the type of operation performed, operative time, the need for reoperation and mortality were studied. The demographics and the outcome between the 2 groups were compared. RESULTS During the study period, 53 neonates had JIA underwent operation in our institute. Seventeen neonates (32%) were associated with CMP. There was no statistical difference on the demographics in the two groups. Patients with CMP had earlier operation than patients with isolated JIA (mean 1.4 d vs 3 d, P = 0.038). Primary anastomosis was performed in 16 patients (94%) with CMP and 30 patients (83%) with isolated JIA (P = 0.269). Patients with CMP had longer operation (mean 190 min vs 154 min, P = 0.004). There were no statistical difference the need for reoperation (3 vs 6, P = 0.606) and mortality (2 vs 1, P = 0.269) between the two groups. CONCLUSION Primary intestinal anastomosis can be performed in 94% of patients with JIA associated with CMP. Although patients with CMP had longer operative time, the mortality and reoperation rates were low and were comparable to patients with isolated JIA. PMID:28224094

Circulating cell-derived microparticles in severe preeclampsia and in fetal growth restriction.

PubMed

Alijotas-Reig, Jaume; Palacio-Garcia, Carles; Farran-Codina, Immaculada; Ruiz-Romance, Mar; Llurba, Elisa; Vilardell-Tarres, Miquel

2012-02-01

The behavior of the circulating microparticles (cMP) in severe preeclampsia (PE) and fetal growth restriction (FGR) is disputed. METHOD OF STUDY  Non-matched case-control study. Seventy cases of severe PE/HELLP/FGR were compared to 38 healthy pregnant women. Twenty healthy non-pregnant women acted as a control. cMP were analyzed using flow cytometry. Results are given as total (annexin-A5-ANXA5+), platelet (CD41+), leukocyte (CD45+), endothelial (CD144+CD31+//CD41-), and CD41-negative cMP/μL of plasma. Antiphospholipid antibodies (aPL) were analyzed through usual methods. Platelet and endothelial cMP increased in healthy pregnant women. PE whole group (PE±FGR) showed an increase in endothelial and CD41-negative, but not in platelet-derived, cMP. Comparing PE whole group versus healthy pregnant, we found cMP levels of endothelial and CD41- had increased. The cMP results obtained in PE group were similar to those of the PE whole group. Comparing PE group to isolated FGR, significant CD41-negative cMP increase was found in PE. According to its aPL positivity, a trend to decrease in leukocyte and endothelial-derived cMP was found in PE group. Normal pregnancy is accompanied by endothelial and platelet cell activation. Endothelial cell activation has been shown in PE but not in isolated FGR. In PE, aPL may contribute to endothelial and possibly to leukocyte cell activation. © 2011 John Wiley & Sons A/S.

42 CFR 417.424 - Denial of enrollment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of § 417.422 if acceptance would— (1) Cause the number of enrollees who are Medicare or Medicaid... substantially nonrepresentative of the general population in the HMO's or CMP's geographic area. (b) Selection... the HMO or CMP substantially nonrepresentative of the general population in the HMO's or CMP's...

Two Fundamental Issues in Multiprocessing.

DTIC Science & Technology

1987-10-01

Structural Model of a Multiprocessor 6 Figure 5: Operational Model of a Multiprocessor 7 Figure 6: The von Neumann Processor (from Gajski and Peir [201) 10...Computer Society, June, 1983. 20. Gajski , D. D. & J-K. Peir. "Essential Issues in Multiprocessor Systems". Computer 18, 6 (June 1985), 9-27. 21. Gurd

Insertion of coherence requests for debugging a multiprocessor

DOEpatents

Blumrich, Matthias A.; Salapura, Valentina

2010-02-23

A method and system are disclosed to insert coherence events in a multiprocessor computer system, and to present those coherence events to the processors of the multiprocessor computer system for analysis and debugging purposes. The coherence events are inserted in the computer system by adding one or more special insert registers. By writing into the insert registers, coherence events are inserted in the multiprocessor system as if they were generated by the normal coherence protocol. Once these coherence events are processed, the processing of coherence events can continue in the normal operation mode.

Method and apparatus for single-stepping coherence events in a multiprocessor system under software control

DOEpatents

Blumrich, Matthias A.; Salapura, Valentina

2010-11-02

An apparatus and method are disclosed for single-stepping coherence events in a multiprocessor system under software control in order to monitor the behavior of a memory coherence mechanism. Single-stepping coherence events in a multiprocessor system is made possible by adding one or more step registers. By accessing these step registers, one or more coherence requests are processed by the multiprocessor system. The step registers determine if the snoop unit will operate by proceeding in a normal execution mode, or operate in a single-step mode.

Shared versus distributed memory multiprocessors

NASA Technical Reports Server (NTRS)

Jordan, Harry F.

1991-01-01

The question of whether multiprocessors should have shared or distributed memory has attracted a great deal of attention. Some researchers argue strongly for building distributed memory machines, while others argue just as strongly for programming shared memory multiprocessors. A great deal of research is underway on both types of parallel systems. Special emphasis is placed on systems with a very large number of processors for computation intensive tasks and considers research and implementation trends. It appears that the two types of systems will likely converge to a common form for large scale multiprocessors.

42 CFR 417.480 - Maintenance of records: Cost HMOs and CMPs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... or CMP, and operation of the HMO's or CMP's financial, medical, and other recordkeeping systems. (2..., sale, or other action. (5) Agreements, contracts, and subcontracts. (6) Franchise, marketing, and management agreements. (7) Schedules of charges for the HMO's or CMP's fee-for-service patients. (8) Matters...

A Designed Angiopoietin-1 Variant, Dimeric CMP-Ang1 Activates Tie2 and Stimulates Angiogenesis and Vascular Stabilization in N-glycan Dependent Manner

PubMed Central

Oh, Nuri; Kim, Kangsan; Jin Kim, Soo; Park, Intae; Lee, Jung-Eun; Suk Seo, Young; Joo An, Hyun; Min Kim, Ho; Young Koh, Gou

2015-01-01

Angiopoietin-1 (Ang1), a potential growth factor for therapeutic angiogenesis and vascular stabilization, is known to specifically cluster and activate Tie2 in high oligomeric forms, which is a unique and essential process in this ligand-receptor interaction. However, highly oligomeric native Ang1 and Ang1 variants are difficult to produce, purify, and store in a stable and active form. To overcome these limitations, we developed a simple and active dimeric CMP-Ang1 by replacing the N-terminal of native Ang1 with the coiled-coil domain of cartilage matrix protein (CMP) bearing mutations in its cysteine residues. This dimeric CMP-Ang1 effectively increased the migration, survival, and tube formation of endothelial cells via Tie2 activation. Furthermore, dimeric CMP-Ang1 induced angiogenesis and suppressed vascular leakage in vivo. Despite its dimeric structure, the potencies of such Tie2-activation-induced effects were comparable to those of a previously engineered protein, COMP-Ang1. We also revealed that these effects of dimeric CMP-Ang1 were affected by specified N-glycosylation in its fibrinogen-like domain. Taken together, our results indicate that dimeric CMP-Ang1 is capable of activating Tie2 and stimulating angiogenesis in N-glycan dependent manner. PMID:26478188

Growth-promoting effects of pepsin- and trypsin-treated caseinomacropeptide from bovine milk on probiotics.

PubMed

Robitaille, Gilles; Champagne, Claude P

2014-08-01

Probiotic Lactobacillus and Bifidobacterium species are generally fastidious bacteria and require rich media for propagation. In milk-based media, they grow poorly, and nitrogen supplementation is required to produce high bacterial biomass levels. It has been reported that caseinomacropeptide (CMP), a 7-kDa peptide released from κ-casein during renneting or gastric digestion, exhibits some growth-promoting activity for lactobacilli and bifidobacteria. During the digestive process, peptides derived from CMP are detected in the intestinal lumen The aim of this study was to evaluate the effects of peptic and tryptic digests of CMP on probiotic lactic acid bacteria growth in de Man, Rogosa and Sharpe broth (MRS) and in milk during fermentation at 37 °C under anaerobic conditions. The study showed that pepsin-treated CMP used as supplements at 0.5 g/l can promote the growth of probiotics even in peptone-rich environments such as MRS. The effect was strain-dependent and evident for the strains that grow poorly in MRS, with an improvement of >1.5 times (P<0.05) by addition of pepsin-treated CMP. Trypsin-treated CMP was much less efficient as growth promoter. Moreover, pepsin-treated CMP was effective in promoting the growth in milk of all probiotic lactic acid bacteria tested, with biomass levels being improved significantly, by 1.7 to 2.6 times (P<0.05), depending on the strain. Thus, supplementation of MRS and of milk with pepsin-treated CMP would be advantageous for the production of high biomass levels for Bifidobacteria and Lactobacilli.

Multiprocessor computer overset grid method and apparatus

DOEpatents

Barnette, Daniel W.; Ober, Curtis C.

2003-01-01

A multiprocessor computer overset grid method and apparatus comprises associating points in each overset grid with processors and using mapped interpolation transformations to communicate intermediate values between processors assigned base and target points of the interpolation transformations. The method allows a multiprocessor computer to operate with effective load balance on overset grid applications.

A large-grain mapping approach for multiprocessor systems through data flow model. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Kim, Hwa-Soo

1991-01-01

A large-grain level mapping method is presented of numerical oriented applications onto multiprocessor systems. The method is based on the large-grain data flow representation of the input application and it assumes a general interconnection topology of the multiprocessor system. The large-grain data flow model was used because such representation best exhibits inherited parallelism in many important applications, e.g., CFD models based on partial differential equations can be presented in large-grain data flow format, very effectively. A generalized interconnection topology of the multiprocessor architecture is considered, including such architectural issues as interprocessor communication cost, with the aim to identify the 'best matching' between the application and the multiprocessor structure. The objective is to minimize the total execution time of the input algorithm running on the target system. The mapping strategy consists of the following: (1) large-grain data flow graph generation from the input application using compilation techniques; (2) data flow graph partitioning into basic computation blocks; and (3) physical mapping onto the target multiprocessor using a priority allocation scheme for the computation blocks.

The Major Soybean Allergen Gly m Bd 28K Induces Hypersensitivity Reactions in Mice Sensitized to Cow's Milk Proteins.

PubMed

Candreva, Ángela María; Smaldini, Paola Lorena; Curciarello, Renata; Fossati, Carlos Alberto; Docena, Guillermo Horacio; Petruccelli, Silvana

2016-02-24

Reactions to soy have been reported in a proportion of patients with IgE-mediated cow's milk allergy (CMA). In this work, we analyzed if Gly m Bd 28K/P28, one of the major soybean allergens, is a cross-reactive allergen with cow milk proteins (CMP). We showed that P28 was recognized by IgE sera from CMA patients and activated human peripheral basophils degranulation. Moreover, IgE sera of mice exclusively sensitized to CMP recognized P28. Splenocytes from sensitized animals secreted IL-5 and IL-13 when incubated with CMP or soy proteins, but only IL-13 when treated with P28. In addition, a skin test was strongly positive for CMP and weakly positive for P28. Remarkably, milk-sensitized mice showed hypersensitivity symptoms following sublingual challenge with P28 or CMP. With the use of bioinformatics' tools seven putative cross-reactive epitopes were identified. In conclusion, using in vitro and in vivo tests we demonstrated that P28 is a novel cross-reactive allergen with CMP.

SPOT4 Operational Control Center (CMP)

NASA Technical Reports Server (NTRS)

Zaouche, G.

1993-01-01

CNES(F) is responsible for the development of a new generation of Operational Control Center (CMP) which will operate the new heliosynchronous remote sensing satellite (SPOT4). This Operational Control Center takes large benefit from the experience of the first generation of control center and from the recent advances in computer technology and standards. The CMP is designed for operating two satellites all the same time with a reduced pool of controllers. The architecture of this CMP is simple, robust, and flexible, since it is based on powerful distributed workstations interconnected through an Ethernet LAN. The application software uses modern and formal software engineering methods, in order to improve quality and reliability, and facilitate maintenance. This software is table driven so it can be easily adapted to other operational needs. Operation tasks are automated to the maximum extent, so that it could be possible to operate the CMP automatically with very limited human interference for supervision and decision making. This paper provides an overview of the SPOTS mission and associated ground segment. It also details the CMP, its functions, and its software and hardware architecture.

Anaerobic biodegradability and methanogenic toxicity of key constituents in copper chemical mechanical planarization effluents of the semiconductor industry.

PubMed

Hollingsworth, Jeremy; Sierra-Alvarez, Reyes; Zhou, Michael; Ogden, Kimberly L; Field, Jim A

2005-06-01

Copper chemical mechanical planarization (CMP) effluents can account for 30-40% of the water discharge in semiconductor manufacturing. CMP effluents contain high concentrations of soluble copper and a complex mixture of organic constituents. The aim of this study is to perform a preliminary assessment of the treatability of CMP effluents in anaerobic sulfidogenic bioreactors inoculated with anaerobic granular sludge by testing individual compounds expected in the CMP effluents. Of all the compounds tested (copper (II), benzotriazoles, polyethylene glycol (M(n) 300), polyethylene glycol (M(n) 860) monooleate, perfluoro-1-octane sulfonate, citric acid, oxalic acid and isopropanol) only copper was found to be inhibitory to methanogenic activity at the concentrations tested. Most of the organic compounds tested were biodegradable with the exception of perfluoro-1-octane sulfonate and benzotriazoles under sulfate reducing conditions and with the exception of the same compounds as well as Triton X-100 under methanogenic conditions. The susceptibility of key components in CMP effluents to anaerobic biodegradation combined with their low microbial inhibition suggest that CMP effluents should be amenable to biological treatment in sulfate reducing bioreactors.

High Performance, Dependable Multiprocessor

NASA Technical Reports Server (NTRS)

Ramos, Jeremy; Samson, John R.; Troxel, Ian; Subramaniyan, Rajagopal; Jacobs, Adam; Greco, James; Cieslewski, Grzegorz; Curreri, John; Fischer, Michael; Grobelny, Eric;

VME rollback hardware for time warp multiprocessor systems

NASA Technical Reports Server (NTRS)

Robb, Michael J.; Buzzell, Calvin A.

1992-01-01

The purpose of the research effort is to develop and demonstrate innovative hardware to implement specific rollback and timing functions required for efficient queue management and precision timekeeping in multiprocessor discrete event simulations. The previously completed phase 1 effort demonstrated the technical feasibility of building hardware modules which eliminate the state saving overhead of the Time Warp paradigm used in distributed simulations on multiprocessor systems. The current phase 2 effort will build multiple pre-production rollback hardware modules integrated with a network of Sun workstations, and the integrated system will be tested by executing a Time Warp simulation. The rollback hardware will be designed to interface with the greatest number of multiprocessor systems possible. The authors believe that the rollback hardware will provide for significant speedup of large scale discrete event simulation problems and allow multiprocessors using Time Warp to dramatically increase performance.

Cm-p5: an antifungal hydrophilic peptide derived from the coastal mollusk Cenchritis muricatus (Gastropoda: Littorinidae)

PubMed Central

López-Abarrategui, Carlos; McBeth, Christine; Mandal, Santi M.; Sun, Zhenyu J.; Heffron, Gregory; Alba-Menéndez, Annia; Migliolo, Ludovico; Reyes-Acosta, Osvaldo; García-Villarino, Mónica; Nolasco, Diego O.; Falcão, Rosana; Cherobim, Mariana D.; Dias, Simoni C.; Brandt, Wolfgang; Wessjohann, Ludger; Starnbach, Michael; Franco, Octavio L.; Otero-González, Anselmo J.

2015-01-01

Antimicrobial peptides form part of the first line of defense against pathogens for many organisms. Current treatments for fungal infections are limited by drug toxicity and pathogen resistance. Cm-p5 (SRSELIVHQRLF), a peptide derived from the marine mollusk Cenchritis muricatus peptide Cm-p1, has a significantly increased fungistatic activity against pathogenic Candida albicans (minimal inhibitory concentration, 10 µg/ml; EC50, 1.146 µg/ml) while exhibiting low toxic effects against a cultured mammalian cell line. Cm-p5 as characterized by circular dichroism and nuclear magnetic resonance revealed an α-helical structure in membrane-mimetic conditions and a tendency to random coil folding in aqueous solutions. Additional studies modeling Cm-p5 binding to a phosphatidylserine bilayer in silico and isothermal titration calorimetry using lipid monophases demonstrated that Cm-p5 has a high affinity for the phospholipids of fungal membranes (phosphatidylserine and phosphatidylethanolamine), only moderate interactions with a mammalian membrane phospholipid, low interaction with ergosterol, and no interaction with chitin. Adhesion of Cm-p5 to living C. albicans cells was confirmed by fluorescence microscopy with FITC-labeled peptide. In a systemic candidiasis model in mice, intraperitoneal administration of Cm-p5 was unable to control the fungal kidney burden, although its low amphiphaticity could be modified to generate new derivatives with improved fungicidal activity and stability.—López-Abarrategui, C., McBeth, C., Mandal, S. M., Sun, Z. J., Heffron, G., Alba-Menéndez, A., Migliolo, L., Reyes-Acosta, O., García-Villarino, M., Nolasco, D. O., Falcão, R., Cherobim, M. D., Dias, S. C., Brandt, W., Wessjohann, L., Starnbach, M., Franco, O. L., Otero-González, A. J. Cm-p5: an antifungal hydrophilic peptide derived from the coastal mollusk Cenchritis muricatus (Gastropoda: Littorinidae). PMID:25921828

42 CFR 417.584 - Payment to HMOs or CMPs with risk contracts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CMP. (a) Principle of payment. CMS makes monthly advance payments equivalent to the HMO's or CMP's per... subsequent monthly payments to take account of the difference. (d) Reduction of payments. If an HMO or CMP... 1998, HMOs or CMPs with risk contracts will be paid in accordance with principles contained in subpart...

42 CFR 417.576 - Final settlement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... end of each contract period, unless CMS extends the period for good cause shown by the HMO or CMP. (2... by common ownership or control; and (B) For reports for cost-reporting periods that begin on or after... CMP or related to the HMO or CMP by common ownership or control and that provides services to the HMO...

Operating system for a real-time multiprocessor propulsion system simulator. User's manual

NASA Technical Reports Server (NTRS)

Cole, G. L.

1985-01-01

The NASA Lewis Research Center is developing and evaluating experimental hardware and software systems to help meet future needs for real-time, high-fidelity simulations of air-breathing propulsion systems. Specifically, the real-time multiprocessor simulator project focuses on the use of multiple microprocessors to achieve the required computing speed and accuracy at relatively low cost. Operating systems for such hardware configurations are generally not available. A real time multiprocessor operating system (RTMPOS) that supports a variety of multiprocessor configurations was developed at Lewis. With some modification, RTMPOS can also support various microprocessors. RTMPOS, by means of menus and prompts, provides the user with a versatile, user-friendly environment for interactively loading, running, and obtaining results from a multiprocessor-based simulator. The menu functions are described and an example simulation session is included to demonstrate the steps required to go from the simulation loading phase to the execution phase.

Assessment of late cardiomyopathy by magnetic resonance imaging in patients with acute promyelocytic leukaemia treated with all-trans retinoic acid and idarubicin.

PubMed

Rodríguez-Veiga, Rebeca; Igual, Begoña; Montesinos, Pau; Tormo, Mar; Sayas, Mª José; Linares, Mariano; Fernández, José María; Salvador, Antonio; Maceira-González, Alicia; Estornell, Jordi; Calabuig, Marisa; Pedreño, María; Roig, Mónica; Sanz, Jaime; Sanz, Guillermo; Carretero, Carlos; Boluda, Blanca; Martínez-Cuadrón, David; Sanz, Miguel Ángel

2017-07-01

Late cardiomyopathy CMP is regarded as a potential severe long-term complication after anthracycline-based regimens for acute promyelocitic leukaemia (APL). We assess by MRI the incidence and severity of clinical and subclinical long-term CMP in a cohort of adult APL patients in first complete remission with PETHEMA trials. Adult patients diagnosed with APL in first complete remission lasting ≥2 years underwent anamnesis and physical examination and were asked to perform a cardiac MRI. Clinical CMP was defined as radiographic and physical signs of heart failure accompanied by symptoms or by left ventricle ejection fraction (LVEF) <45% by MRI with or without symptoms. Subclinical CMP was defined as the following MRI abnormalities: LVEF 45-50% or late gadolinium enhancement or two or more of LVEF ≤55%, left ventricle end-diastolic volume index ≥98 ml/m 2 , left ventricle end-systolic volume index ≥38 ml/m 2 , right ventricle end-diastolic volume index ≥106 ml/m 2 and regional wall motion abnormalities. Of the 82 patients enrolled in the study, median cumulative dose of anthracyclines (doxorubicin equivalence) was 650 mg/m 2 , and median time from APL diagnosis to the study was 87 months (range, 24-195). Seven out of 57 patients with available MRI (12%) had subclinical CMP (all of them showed late gadolinium enhancement in MRI), and none had clinical CMP. Among the 25 patients without MRI, none had CMP by chest X-ray and physical assessment. In summary, we found 12% of subclinical and no clinical late CMP assessed by MRI in APL patients treated with PETHEMA protocols. Due to the low number of patients, we must interpret our results cautiously.

In vivo evidence of cross-reactivity between cow's milk and soybean proteins in a mouse model of food allergy.

PubMed

Smaldini, Paola; Curciarello, Renata; Candreva, Angela; Rey, María Amanda; Fossati, Carlos Alberto; Petruccelli, Silvana; Docena, Guillermo Horacio

2012-01-01

Cow's milk allergy (CMA) is an important problem worldwide and the development of an in vivo system to study new immunotherapeutic strategies is of interest. Intolerance to soybean formula has been described in CMA patients, but it is not fully understood. In this work, we used a food allergy model in BALB/c mice to study the cross-reactivity between cow's milk protein (CMP) and soy proteins (SP). Mice were orally sensitized with cholera toxin and CMP, and then challenged with CMP or SP to induce allergy. Elicited symptoms, plasma histamine, humoral and cellular immune response were analyzed. Th1- and Th2-associated cytokines and transcription factors were assessed at mucosal sites and in splenocytes. Cutaneous tests were also performed. We found that the immediate symptoms elicited in CMP-sensitized mice orally challenged with SP were consistent with a plasma histamine increase. The serum levels of CMP-specific IgE and IgG1 antibodies were increased. These antibodies also recognized soy proteins. Splenocytes and mesenteric lymph node cells incubated with CMP or SP secreted IL-5 and IL-13. mRNA expression of Th2-associated genes (IL-5, IL-13, and GATA-3) was upregulated in mucosal samples. In addition, sensitized animals exhibited positive cutaneous tests after the injection of CMP or SP. We demonstrate that CMP-sensitized mice, without previous exposure to soy proteins, elicited hypersensitivity signs immediately after the oral administration of SP, suggesting that the immunochemical cross-reactivity might be clinically relevant. This model may provide an approach to further characterize cross-allergenicity phenomena and develop new immunotherapeutic treatments for allergic patients. Copyright © 2012 S. Karger AG, Basel.

Novel cytidine-based orotidine-5'-monophosphate decarboxylase inhibitors with an unusual twist.

PubMed

Purohit, Meena K; Poduch, Ewa; Wei, Lianhu William; Crandall, Ian Edward; To, Terrence; Kain, Kevin C; Pai, Emil F; Kotra, Lakshmi P

2012-11-26

Orotidine-5'-monophosphate decarboxylase (ODCase) is an interesting enzyme with an unusual catalytic activity and a potential drug target in Plasmodium falciparum, which causes malaria. ODCase has been shown to exhibit unusual and interesting interactions with a variety of nucleotide ligands. Cytidine-5'-monophosphate (CMP) is a poor ligand of ODCase, and CMP binds to the active site of ODCase with an unusual orientation and conformation. We designed N3- and N4-modified CMP derivatives as novel ligands to ODCase. These novel CMP derivatives and their corresponding nucleosides were evaluated against Plasmodium falciparum ODCase and parasitic cultures, respectively. These derivatives exhibited improved inhibition of the enzyme catalytic activity, displayed interesting binding conformations and unusual molecular rearrangements of the ligands. These findings with the modified CMP nucleotides underscored the potential of transformation of poor ligands to ODCase into novel inhibitors of this drug target.

A client-treatment matching protocol for therapeutic communities: first report.

PubMed

Melnick, G; De Leon, G; Thomas, G; Kressel, D

2001-10-01

The present study is the first report on a client-treatment matching protocol (CMP) to guide admissions to residential and outpatient substance abuse treatment settings. Two cohorts, a field test sample (n = 318) and cross-validation (n = 407) sample were drawn from consecutive admissions to nine geographically distributed multisetting therapeutic communities (TCs). A passive matching design was employed. Clients received the CMP on admission, but agencies were "blind" to the CMP treatment recommendation (i.e., match) and assigned clients to treatment by the usual intake procedures. Bivariate and logistical regression analyses show that positive treatment dispositions (treatment completion or longer retention in treatment)) were significantly higher among the CMP-matched clients. The present findings provide the empirical basis for studies assessing the validity and utility of the CMP with controlled designs. Though limited to TC-oriented agencies, the present research supports the use of objective matching criteria to improve treatment.

VxWorks 6.9 for LEON

NASA Astrophysics Data System (ADS)

Cederman, Daniel; Hellstrom, Daniel

2016-08-01

The VxWorks operating system together with the Cobham Grislier LEON architectural port provides an efficient platform for the development of software for space applications. It supports both uni-and multiprocessor mode (SMP or AMP) and comes with an integrated development environment with several debugging and analysis tools. The LEON architectural port from Cobham Grislier supports LEON2/3/4 systems and includes drivers for all standard on-chip peripherals, as well as support for RASTA boards. In this paper we will highlight some the many features of VxWorks and the LEON architectural port. The latest version of the architectural port now supports VxWorks 6.9 (the previous version was for VxWorks 6.7) and has the support for the GR740, the commercially available quad-core LEON system, designed as the European Space Agency's Next Generation Microprocessor (NGMP).

Resource Management for Distributed Parallel Systems

NASA Technical Reports Server (NTRS)

Neuman, B. Clifford; Rao, Santosh

1993-01-01

Multiprocessor systems should exist in the the larger context of distributed systems, allowing multiprocessor resources to be shared by those that need them. Unfortunately, typical multiprocessor resource management techniques do not scale to large networks. The Prospero Resource Manager (PRM) is a scalable resource allocation system that supports the allocation of processing resources in large networks and multiprocessor systems. To manage resources in such distributed parallel systems, PRM employs three types of managers: system managers, job managers, and node managers. There exist multiple independent instances of each type of manager, reducing bottlenecks. The complexity of each manager is further reduced because each is designed to utilize information at an appropriate level of abstraction.

42 CFR 417.560 - Apportionment: Part B physician and supplier services.

Code of Federal Regulations, 2010 CFR

2010-10-01

... HMO or CMP or by a related entity of the HMO or CMP must be apportioned on the basis of the ratio of... reasonable cost the HMO or CMP pays under its financial arrangement with the physician or supplier must be apportioned between Medicare enrollees and others based on the ratio of covered services furnished to Medicare...

Timing of Bag Application and Removal in Controlled Mass Pollination

Treesearch

F.E. Bridgwater; D.L. Bramlett; V.D. Hipkins

1999-01-01

Controlled mass pollination (CMP) among outstanding parents is one way to increase genetic gains from traditional wind-pollinated seed orchards, but the economic success of CMP depends on both genetic gains and costs. CMP has been shown. to be cost-effective (Bridgwater et al. 1998) even when costs were adjusted for risk (Byram and Bridgwater 1999, These Proceedings...

42 CFR 417.460 - Disenrollment of beneficiaries by an HMO or CMP.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or CMP's geographic area does not expand that area to encompass the location of the enrollee's new... to the HMO's or CMP's geographic area within 1 year from the date he or she left that area, the HMO... date the enrollee left that area in accordance with paragraph (f)(1) of this section. (g) Failure to...

42 CFR 417.460 - Disenrollment of beneficiaries by an HMO or CMP.

Code of Federal Regulations, 2010 CFR

2010-10-01

... or CMP's geographic area does not expand that area to encompass the location of the enrollee's new... to the HMO's or CMP's geographic area within 1 year from the date he or she left that area, the HMO... date the enrollee left that area in accordance with paragraph (f)(1) of this section. (g) Failure to...

Design of an ultraprecision computerized numerical control chemical mechanical polishing machine and its implementation

NASA Astrophysics Data System (ADS)

Zhang, Chupeng; Zhao, Huiying; Zhu, Xueliang; Zhao, Shijie; Jiang, Chunye

2018-01-01

The chemical mechanical polishing (CMP) is a key process during the machining route of plane optics. To improve the polishing efficiency and accuracy, a CMP model and machine tool were developed. Based on the Preston equation and the axial run-out error measurement results of the m circles on the tin plate, a CMP model that could simulate the material removal at any point on the workpiece was presented. An analysis of the model indicated that lower axial run-out error led to lower material removal but better polishing efficiency and accuracy. Based on this conclusion, the CMP machine was designed, and the ultraprecision gas hydrostatic guideway and rotary table as well as the Siemens 840Dsl numerical control system were incorporated in the CMP machine. To verify the design principles of machine, a series of detection and machining experiments were conducted. The LK-G5000 laser sensor was employed for detecting the straightness error of the gas hydrostatic guideway and the axial run-out error of the gas hydrostatic rotary table. A 300-mm-diameter optic was chosen for the surface profile machining experiments performed to determine the CMP efficiency and accuracy.

File-System Workload on a Scientific Multiprocessor

NASA Technical Reports Server (NTRS)

Kotz, David; Nieuwejaar, Nils

1995-01-01

Many scientific applications have intense computational and I/O requirements. Although multiprocessors have permitted astounding increases in computational performance, the formidable I/O needs of these applications cannot be met by current multiprocessors a their I/O subsystems. To prevent I/O subsystems from forever bottlenecking multiprocessors and limiting the range of feasible applications, new I/O subsystems must be designed. The successful design of computer systems (both hardware and software) depends on a thorough understanding of their intended use. A system designer optimizes the policies and mechanisms for the cases expected to most common in the user's workload. In the case of multiprocessor file systems, however, designers have been forced to build file systems based only on speculation about how they would be used, extrapolating from file-system characterizations of general-purpose workloads on uniprocessor and distributed systems or scientific workloads on vector supercomputers (see sidebar on related work). To help these system designers, in June 1993 we began the Charisma Project, so named because the project sought to characterize 1/0 in scientific multiprocessor applications from a variety of production parallel computing platforms and sites. The Charisma project is unique in recording individual read and write requests-in live, multiprogramming, parallel workloads (rather than from selected or nonparallel applications). In this article, we present the first results from the project: a characterization of the file-system workload an iPSC/860 multiprocessor running production, parallel scientific applications at NASA's Ames Research Center.

Stable curcumin-loaded polymeric micellar formulation for enhancing cellular uptake and cytotoxicity to FLT3 overexpressing EoL-1 leukemic cells.

PubMed

Tima, Singkome; Anuchapreeda, Songyot; Ampasavate, Chadarat; Berkland, Cory; Okonogi, Siriporn

2017-05-01

The present study aims to develop a stable polymeric micellar formulation of curcumin (CM) with improved solubility and stability, and that is suitable for clinical applications in leukemia patients. CM-loaded polymeric micelles (CM-micelles) were prepared using poloxamers. The chemical structure of the polymers influenced micellar properties. The best formulation of CM-micelles, namely CM-P407, was obtained from poloxamer 407 at drug to polymer ratio of 1:30 and rehydrated with phosphate buffer solution pH 7.4. CM-P407 exhibited the smallest size of 30.3±1.3nm and highest entrapment efficiency of 88.4±4.1%. When stored at -80°C for 60days, CM-P407 retained high protection of CM and had no significant size change. In comparison with CM solution in dimethyl sulfoxide (CM-DMSO), CM kinetic degradation in both formulations followed a pseudo-first-order reaction, but the half-life of CM in CM-P407 was approx. 200 times longer than in CM-DMSO. Regarding the activity against FLT3 overexpressing EoL-1 leukemic cells, CM-P407 showed higher cytotoxicity than CM-DMSO. Moreover, intracellular uptake to leukemic cells of CM-P407 was 2-3 times greater than that of CM-DMSO. These promising results for CM-P407 will be further investigated in rodents and in clinical studies for leukemia treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

Mechanistic, kinetic, and processing aspects of tungsten chemical mechanical polishing

NASA Astrophysics Data System (ADS)

Stein, David

This dissertation presents an investigation into tungsten chemical mechanical polishing (CMP). CMP is the industrially predominant unit operation that removes excess tungsten after non-selective chemical vapor deposition (CVD) during sub-micron integrated circuit (IC) manufacture. This work explores the CMP process from process engineering and fundamental mechanistic perspectives. The process engineering study optimized an existing CMP process to address issues of polish pad and wafer carrier life. Polish rates, post-CMP metrology of patterned wafers, electrical test data, and synergy with a thermal endpoint technique were used to determine the optimal process. The oxidation rate of tungsten during CMP is significantly lower than the removal rate under identical conditions. Tungsten polished without inhibition during cathodic potentiostatic control. Hertzian indenter model calculations preclude colloids of the size used in tungsten CMP slurries from indenting the tungsten surface. AFM surface topography maps and TEM images of post-CMP tungsten do not show evidence of plow marks or intergranular fracture. Polish rate is dependent on potassium iodate concentration; process temperature is not. The colloid species significantly affects the polish rate and process temperature. Process temperature is not a predictor of polish rate. A process energy balance indicates that the process temperature is predominantly due to shaft work, and that any heat of reaction evolved during the CMP process is negligible. Friction and adhesion between alumina and tungsten were studied using modified AFM techniques. Friction was constant with potassium iodate concentration, but varied with applied pressure. This corroborates the results from the energy balance. Adhesion between the alumina and the tungsten was proportional to the potassium iodate concentration. A heuristic mechanism, which captures the relationship between polish rate, pressure, velocity, and slurry chemistry, is presented. In this mechanism, the colloid reacts with the chemistry of the slurry to produce active sites. These active sites become inactive by removing tungsten from the film. The process repeats when then inactive sites are reconverted to active sites. It is shown that the empirical form of the heuristic mechanism fits all of the data obtained. The mechanism also agrees with the limiting cases that were investigated.

Engineering Sialic Acid Synthesis Ability in Insect Cells.

PubMed

Viswanathan, Karthik; Narang, Someet; Betenbaugh, Michael J

2015-01-01

Insect cells lack the ability to synthesize the sialic acid donor molecule CMP-sialic acid or its precursor, sialic acid. In this chapter, we describe a method to engineer CMP-sialic acid synthesis capability into Spodoptera frugiperda (Sf9) cells, a prototypical insect cell line, by recombinant expression of sialic acid synthesis pathway genes using baculovirus technology. Co-expression of a sialuria mutant UDP-GlcNAc-2-epimerase/ManNAc kinase (EKR263L), wild-type sialic acid 9-phosphate synthase (SAS), and wild-type CMP-sialic acid synthetase (CSAS) in the presence of GlcNAc leads to synthesis of CMP-sialic acids synthesis to support sialylation of N-glycans on glycoproteins.

Shared performance monitor in a multiprocessor system

DOEpatents

Chiu, George; Gara, Alan G.; Salapura, Valentina

2012-07-24

A performance monitoring unit (PMU) and method for monitoring performance of events occurring in a multiprocessor system. The multiprocessor system comprises a plurality of processor devices units, each processor device for generating signals representing occurrences of events in the processor device, and, a single shared counter resource for performance monitoring. The performance monitor unit is shared by all processor cores in the multiprocessor system. The PMU comprises: a plurality of performance counters each for counting signals representing occurrences of events from one or more the plurality of processor units in the multiprocessor system; and, a plurality of input devices for receiving the event signals from one or more processor devices of the plurality of processor units, the plurality of input devices programmable to select event signals for receipt by one or more of the plurality of performance counters for counting, wherein the PMU is shared between multiple processing units, or within a group of processors in the multiprocessing system. The PMU is further programmed to monitor event signals issued from non-processor devices.

A cache-aided multiprocessor rollback recovery scheme

NASA Technical Reports Server (NTRS)

Wu, Kun-Lung; Fuchs, W. Kent

1989-01-01

This paper demonstrates how previous uniprocessor cache-aided recovery schemes can be applied to multiprocessor architectures, for recovering from transient processor failures, utilizing private caches and a global shared memory. As with cache-aided uniprocessor recovery, the multiprocessor cache-aided recovery scheme of this paper can be easily integrated into standard bus-based snoopy cache coherence protocols. A consistent shared memory state is maintained without the necessity of global check-pointing.

Atomic-scale and pit-free flattening of GaN by combination of plasma pretreatment and time-controlled chemical mechanical polishing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Hui; Endo, Katsuyoshi; Yamamura, Kazuya, E-mail: yamamura@upst.eng.osaka-u.ac.jp

2015-08-03

Chemical mechanical polishing (CMP) combined with atmospheric-pressure plasma pretreatment was applied to a GaN (0001) substrate. The irradiation of a CF{sub 4}-containing plasma was proven to be very useful for modifying the surface of GaN. When CMP was conducted on a plasma-irradiated surface, a modified layer of GaF{sub 3} acted as a protective layer on GaN by preventing the formation of etch pits. Within a short duration (8 min) of CMP using a commercially available CeO{sub 2} slurry, an atomically flat surface with a root mean square (rms) roughness of 0.11 nm was obtained. Moreover, etch pits, which are inevitably introduced inmore » conventional CMP, could not be observed at the dislocation sites on the polished GaN surface. It was revealed that CMP combined with the plasma pretreatment was very effective for obtaining a pit-free and atomically flat GaN surface.« less

Distinct Signaling Roles of cIMP, cCMP, and cUMP.

PubMed

Seifert, Roland

2016-10-04

The cyclic purine nucleotide cIMP and the cyclic pyrimidine nucleotides cCMP and cUMP are emerging second messengers. These cNMPs show different biological effects, but the molecular mechanisms remain elusive. In this issue of Structure, Ng et al. (2016) provide structural evidence for distinct interactions of cIMP, cCMP, and cUMP with ion channels. Copyright © 2016 Elsevier Ltd. All rights reserved.

Medicinal Chemistry of the Noncanonical Cyclic Nucleotides cCMP and cUMP.

PubMed

Schwede, Frank; Rentsch, Andreas; Genieser, Hans-Gottfried

2017-01-01

After decades of intensive research on adenosine-3',5'-cyclic monophosphate (cAMP)- and guanosine-3',5'-cyclic monophosphate (cGMP)-related second messenger systems, also the noncanonical congeners cyclic cytidine-3',5'-monophosphate (cCMP) and cyclic uridine-3',5'-monophosphate (cUMP) gained more and more interest. Until the late 1980s, only a small number of cCMP and cUMP analogs with sometimes undefined purities had been described. Moreover, most of these compounds had been rather synthesized as precursors of antitumor and antiviral nucleoside-5'-monophosphates and hence had not been tested for any second messenger activity. Along with the recurring interest in cCMP- and cUMP-related signaling in the early 2000s, it became evident that well-characterized small molecule analogs with reliable purities would serve as highly valuable tools for the evaluation of a putative second messenger role of cyclic pyrimidine nucleotides. Meanwhile, for this purpose new cCMP and cUMP derivatives have been developed, and already known analogs have been resynthesized and highly purified. This chapter summarizes early medicinal chemistry work on cCMP and cUMP and analogs thereof, followed by a description of recent synthetic developments and an outlook on potential future directions.

Dynamic NMR Study of Model CMP Slurry Containing Silica Particles as Abrasives

NASA Astrophysics Data System (ADS)

Odeh, F.; Al-Bawab, A.; Li, Y.

2018-02-01

Chemical mechanical planarization (CMP) should provide a good surface planarity with minimal surface defectivity. Since CMP slurries are multi-component systems, it is very important to understand the various processes and interactions taking place in such slurries. Several techniques have been employed for such task, however, most of them lack the molecular recognition to investigate molecular interactions without adding probes which in turn increase complexity and might alter the microenvironment of the slurry. Nuclear magnetic resonance (NMR) is a powerful technique that can be employed in such study. The longitudinal relaxation times (T1) of the different components of CMP slurries were measured using Spin Echo-NMR (SE-NMR) at a constant temperature. The fact that NMR is non-invasive and gives information on the molecular level gives more advantage to the technique. The model CMP slurry was prepared in D2O to enable monitoring of T1 for the various components' protons. SE-NMR provide a very powerful tool to study the various interactions and adsorption processes that take place in a model CMP silica based slurry which contains BTA and/or glycine and/or Cu+2 ions. It was found that BTA is very competitive towards complexation with Cu+2 ions and BTA-Cu complex adsorbs on silica surface.

Matrix Metalloproteinases and their Tissue Inhibitors in Cardiac Amyloidosis: Relationship to Structural, Functional Myocardial Changes and to Light Chain Amyloid Deposition

PubMed Central

Biolo, Andreia; Ramamurthy, Sujata; Connors, Lawreen H.; O'Hara, Carl J.; Meier-Ewert, Hans K.; Hoo, Pamela T. Soo; Sawyer, Douglas B.; Seldin, David S.; Sam, Flora

2009-01-01

Background Cardiac amyloidosis is characterized by amyloid infiltration resulting in extracellular matrix (ECM) disruption. Amyloid cardiomyopathy due to immunoglobulin light chain protein (AL-CMP) deposition, has an accelerated clinical course and a worse prognosis compared to non-light chain cardiac amyloidoses i.e., forms associated with wild-type or mutated transthyretin (TTR). We therefore tested the hypothesis that determinants of proteolytic activity of the ECM, the matrix metalloproteinases (MMPs) and their tissue inhibitors (TIMPs), would have distinct patterns and contribute to the pathogenesis of AL-CMP vs. TTR. Methods / Results We studied 40 patients with systemic amyloidosis: 10 AL-CMP patients, 20 patients with TTR-associated forms of cardiac amyloidosis, i.e. senile systemic amyloidois (SSA, involving wild-type TTR) or mutant TTR (ATTR), and 10 patients with AL amyloidosis without cardiac involvement. Serum MMP-2 and −9, TIMP-1, −2 and −4, brain natriuretic peptide (BNP) values and echocardiography were determined. AL-CMP and SSA-ATTR groups had similar degrees of increased left ventricular wall thickness (LVWT). However, BNP, MMP-9 and TIMP-1 levels were distinctly elevated accompanied by marked diastolic dysfunction in the AL-CMP group vs. no or minimal increases in the SSA-ATTR group. BNP, MMPs and TIMPs were not correlated with the degree of LVWT but were correlated to each other and to measures of diastolic dysfunction. Immunostaining of human endomyocardial biopsies showed diffuse expression of MMP-9 and TIMP-1 in AL-CMP and limited expression in SSA or ATTR hearts. Conclusions Despite comparable LVWT with TTR-related cardiac amyloidosis, AL-CMP patients have higher BNP, MMPs and TIMPs, which correlated with diastolic dysfunction. These findings suggest a relationship between light chains and ECM proteolytic activation that may play an important role in the functional and clinical manifestations of AL-CMP, distinct from the other non-light chain cardiac amyloidoses. PMID:19808299

Mechanism of amino acid interaction with silicon nitride surface during chemical mechanical planarization

NASA Astrophysics Data System (ADS)

America, William George

Chemical-Mechanical Planarization (CMP) has become an essential technology for making modern semiconductor devices. This technique was originally applied to overcome the depth of focus limitations of lithography tools during pattern development of metal and dielectric films. As features of the semiconductor device became smaller the lithographic process shifted to shorter exposure wavelengths and the useable depth of focus became smaller. The topography differences on the wafer's surface from all of the previous processing steps became greater than the exposure tools could properly project. CMP helped solve this problem by bringing the features of the wafer surface to the same plane. As semiconductor fabrication technology progressed further, CMP was applied to other areas of the process, including shallow trench isolation and metal line Damascene processing. In its simplest application, CMP polishes on features projecting upward and higher than the average surface. These projections experience more work and are polished faster. Given sufficient time the surface becomes essentially flat, on a micro-scale, and the lithographic projection tools has the same plane onto which to focus. Thus, the pattern is properly and uniformly exposed and subsequent reactive ion etching (RIE) steps are executed. This technique was initially applied to later steps in the wafer processing scheme to render a new flat surface at each metal layer. Building on this success, CMP has been applied to a broad range of steps in the wafer processing particularly where surface topography warrants and when RIE of dielectric or metallic films is not practical. CMP has seen its greatest application in semiconductor logic and memory devices and most recently, a Damascene processing for copper lines and shallow trench isolation. This pattern dependent CMP issue is explored in this thesis as it pertains primarily to shallow trench isolation CMP coupled with a highly selective slurry chemistry.

Smart-Pixel Array Processors Based on Optimal Cellular Neural Networks for Space Sensor Applications

NASA Technical Reports Server (NTRS)

Fang, Wai-Chi; Sheu, Bing J.; Venus, Holger; Sandau, Rainer

1997-01-01

A smart-pixel cellular neural network (CNN) with hardware annealing capability, digitally programmable synaptic weights, and multisensor parallel interface has been under development for advanced space sensor applications. The smart-pixel CNN architecture is a programmable multi-dimensional array of optoelectronic neurons which are locally connected with their local neurons and associated active-pixel sensors. Integration of the neuroprocessor in each processor node of a scalable multiprocessor system offers orders-of-magnitude computing performance enhancements for on-board real-time intelligent multisensor processing and control tasks of advanced small satellites. The smart-pixel CNN operation theory, architecture, design and implementation, and system applications are investigated in detail. The VLSI (Very Large Scale Integration) implementation feasibility was illustrated by a prototype smart-pixel 5x5 neuroprocessor array chip of active dimensions 1380 micron x 746 micron in a 2-micron CMOS technology.

Nuclear Science Symposium, 31st and Symposium on Nuclear Power Systems, 16th, Orlando, FL, October 31-November 2, 1984, Proceedings

NASA Technical Reports Server (NTRS)

Biggerstaff, J. A. (Editor)

1985-01-01

Topics related to physics instrumentation are discussed, taking into account cryostat and electronic development associated with multidetector spectrometer systems, the influence of materials and counting-rate effects on He-3 neutron spectrometry, a data acquisition system for time-resolved muscle experiments, and a sensitive null detector for precise measurements of integral linearity. Other subjects explored are concerned with space instrumentation, computer applications, detectors, instrumentation for high energy physics, instrumentation for nuclear medicine, environmental monitoring and health physics instrumentation, nuclear safeguards and reactor instrumentation, and a 1984 symposium on nuclear power systems. Attention is given to the application of multiprocessors to scientific problems, a large-scale computer facility for computational aerodynamics, a single-board 32-bit computer for the Fastbus, the integration of detector arrays and readout electronics on a single chip, and three-dimensional Monte Carlo simulation of the electron avalanche in a proportional counter.

A novel highly selective 5-HT6 receptor antagonist attenuates ethanol and nicotine seeking but does not affect inhibitory response control in Wistar rats.

PubMed

de Bruin, N M W J; McCreary, A C; van Loevezijn, A; de Vries, T J; Venhorst, J; van Drimmelen, M; Kruse, C G

2013-01-01

Recent studies suggest a potential role for 5-hydroxytryptamine(6) (5-HT(6)) receptors in the regulation of addictive behavior. In the present study, our aim was to investigate whether the novel highly selective 5-HT(6) receptor antagonist compound (CMP) 42 affected nicotine and ethanol seeking behavior in Wistar rats. We have also studied whether CMP 42 had beneficial effects in a model of impulse control, as measured in the 5-choice serial reaction time task (5-CSRTT). Rats were trained to nose poke to receive intravenous infusions of nicotine or an ethanol drop. CMP 42 (3-30 mg/kg intraperitoneally, i.p.) was administered to investigate the effects on nicotine self-administration. Rats were also tested for cue-induced reinstatement of nicotine and ethanol seeking. In addition, the effects of CMP 42 were studied on the number of anticipatory responses in the 5-CSRTT. CMP 42 was effective in reducing nicotine self-administration and reinstatement of nicotine seeking at a dose of 30 mg/kg (i.p.). CMP 42 was also effective in reducing reinstatement of ethanol seeking (30 mg/kg i.p.). In contrast, CMP 42 did not affect anticipatory responding at doses tested, indicating no effects on impulse control. These results add to a body of evidence implicating the 5-HT(6) receptor as a viable target for the control of drug abuse. Specifically, we demonstrated for the first time effects on nicotine self-administration and on nicotine and ethanol reinstatement. Further, these effects are probably not mediated by effects on impulse control. Copyright © 2012 Elsevier B.V. All rights reserved.

Microbiomes of Endodontic-Periodontal Lesions before and after Chemomechanical Preparation.

PubMed

Gomes, Brenda P F A; Berber, Vanessa B; Kokaras, Alexis S; Chen, Tsute; Paster, Bruce J

2015-12-01

This study was conducted to evaluate the microbiomes of endodontic-periodontal lesions before and after chemomechanical preparation (CMP). Clinical samples were taken from 15 root canals (RCs) with necrotic pulp tissues and from their associated periodontal pockets (PPs) (n = 15) of teeth with endodontic-periodontal lesions before and after CMP. The Human Oral Microbe Identification using Next Generation Sequencing (NGS) protocol and viable culture were used to analyze samples from RCs and PPs. The Mann-Whitney U test and Benjamini-Hochberg corrections were performed to correlate the clinical and radiographic findings with microbial findings (P < .05). Bacteria were detected in 100% of the samples in both sites (15/15) using NGS. Firmicutes was the most predominant phylum in both sites using both methods. The most frequently detected species in the RCs before and after CMP using NGS were Enterococcus faecalis, Parvimonas micra, Mogibacterium timidum, Filifactor alocis, and Fretibacterium fastidiosum. The species most frequently detected in the PPs before and after CMP using NGS were P. micra, E. faecalis, Streptococcus constellatus, Eubacterium brachy, Tannerella forsythia, and F. alocis. Associations were found between periapical lesions ≤ 2 mm and Desulfobulbus sp oral taxon 041 and with periodontal pockets ≥ 6 mm and Dialister invisius and Peptostreptococcus stomatis (all P < .05, found in the RCs before CMP). It is concluded that the microbial community present in combined endodontic-periodontal lesions is complex and more diverse than previously reported. It is important to note that bacteria do survive in some root canals after CMP. Finally, the similarity between the microbiota of both sites, before and after CMP, suggests there may be a pathway of infection between the pulp and periodontium. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

SEMICONDUCTOR TECHNOLOGY Dummy fill effect on CMP planarity

NASA Astrophysics Data System (ADS)

Junxiong, Zhou; Lan, Chen; Wenbiao, Ruan; Zhigang, Li; Weixiang, Shen; Tianchun, Ye

2010-10-01

With the use of a chemical-mechanical polishing (CMP) simulator verified by testing data from a foundry, the effect of dummy fill characteristics, such as fill size, fill density and fill shape, on CMP planarity is analyzed. The results indicate that dummy density has a significant impact on oxide erosion, and copper dishing is in proportion to dummy size. We also demonstrate that cross shape dummy fill can have the best dishing performance at the same density.

An innovative method of ocular prosthesis fabrication by bio-CAD and rapid 3-D printing technology: A pilot study.

PubMed

Alam, Md Shahid; Sugavaneswaran, M; Arumaikkannu, G; Mukherjee, Bipasha

2017-08-01

Ocular prosthesis is either a readymade stock shell or custom made prosthesis (CMP). Presently, there is no other technology available, which is either superior or even comparable to the conventional CMP. The present study was designed to fabricate ocular prosthesis using computer aided design (CAD) and rapid manufacturing (RM) technology and to compare it with custom made prosthesis (CMP). The ocular prosthesis prepared by CAD was compared with conventional CMP in terms of time taken for fabrication, weight, cosmesis, comfort, and motility. Two eyes of two patients were included. Computerized tomography scan of wax model of socket was converted into three dimensional format using Materialize Interactive Medical Image Control System (MIMICS)software and further refined. This was given as an input to rapid manufacturing machine (Polyjet 3-D printer). The final painting on prototype was done by an ocularist. The average effective time required for fabrication of CAD prosthesis was 2.5 hours; and weight 2.9 grams. The same for CMP were 10 hours; and 4.4 grams. CAD prosthesis was more comfortable for both the patients. The study demonstrates the first ever attempt of fabricating a complete ocular prosthesis using CAD and rapid manufacturing and comparing it with conventional CMP. This prosthesis takes lesser time for fabrication, and is more comfortable. Studies with larger sample size will be required to further validate this technique.

Application of AI methods to aircraft guidance and control

NASA Technical Reports Server (NTRS)

Hueschen, Richard M.; Mcmanus, John W.

1988-01-01

A research program for integrating artificial intelligence (AI) techniques with tools and methods used for aircraft flight control system design, development, and implementation is discussed. The application of the AI methods for the development and implementation of the logic software which operates with the control mode panel (CMP) of an aircraft is presented. The CMP is the pilot control panel for the automatic flight control system of a commercial-type research aircraft of Langley Research Center's Advanced Transport Operating Systems (ATOPS) program. A mouse-driven color-display emulation of the CMP, which was developed with AI methods and used to test the AI software logic implementation, is discussed. The operation of the CMP was enhanced with the addition of a display which was quickly developed with AI methods. The display advises the pilot of conditions not satisfied when a mode does not arm or engage. The implementation of the CMP software logic has shown that the time required to develop, implement, and modify software systems can be significantly reduced with the use of the AI methods.

Parallel and fault-tolerant algorithms for hypercube multiprocessors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aykanat, C.

1988-01-01

Several techniques for increasing the performance of parallel algorithms on distributed-memory message-passing multi-processor systems are investigated. These techniques are effectively implemented for the parallelization of the Scaled Conjugate Gradient (SCG) algorithm on a hypercube connected message-passing multi-processor. Significant performance improvement is achieved by using these techniques. The SCG algorithm is used for the solution phase of an FE modeling system. Almost linear speed-up is achieved, and it is shown that hypercube topology is scalable for an FE class of problem. The SCG algorithm is also shown to be suitable for vectorization, and near supercomputer performance is achieved on a vectormore » hypercube multiprocessor by exploiting both parallelization and vectorization. Fault-tolerance issues for the parallel SCG algorithm and for the hypercube topology are also addressed.« less

Development and evaluation of a fault-tolerant multiprocessor (FTMP) computer. Volume 1: FTMP principles of operation

NASA Technical Reports Server (NTRS)

Smith, T. B., Jr.; Lala, J. H.

1983-01-01

The basic organization of the fault tolerant multiprocessor, (FTMP) is that of a general purpose homogeneous multiprocessor. Three processors operate on a shared system (memory and I/O) bus. Replication and tight synchronization of all elements and hardware voting is employed to detect and correct any single fault. Reconfiguration is then employed to repair a fault. Multiple faults may be tolerated as a sequence of single faults with repair between fault occurrences.

Compiler-directed cache management in multiprocessors

NASA Technical Reports Server (NTRS)

Cheong, Hoichi; Veidenbaum, Alexander V.

1990-01-01

The necessity of finding alternatives to hardware-based cache coherence strategies for large-scale multiprocessor systems is discussed. Three different software-based strategies sharing the same goals and general approach are presented. They consist of a simple invalidation approach, a fast selective invalidation scheme, and a version control scheme. The strategies are suitable for shared-memory multiprocessor systems with interconnection networks and a large number of processors. Results of trace-driven simulations conducted on numerical benchmark routines to compare the performance of the three schemes are presented.

Multi-scale reflection modulator-based optical interconnects

NASA Astrophysics Data System (ADS)

Nair, Rohit

This dissertation describes the design, analysis, and experimental validation of micro- and macro-optical components for implementing optical interconnects at multiple scales for varied applications. Three distance scales are explored: millimeter, centimeter, and meter-scales. At the millimeter-scale, we propose the use of optical interconnects at the intra-chip level. With the rapid scaling down of CMOS critical dimensions in accordance to Moore's law, the bandwidth requirements of global interconnects in microprocessors has exceeded the capabilities of metal links. These are the wires that connect the most remote parts of the chip and are disproportionately problematic in terms of chip area and power consumption. Consequently, in the mid-2000s, we saw a shift in the chip architecture: a move towards multicore designs. However, this only delays the inevitable communication bottleneck between cores. To satisfy this bandwidth, we propose to replace the global metal interconnects with optical interconnects. We propose to use the hybrid integration of silicon with GaAs/AlAs-based multiple quantum well devices as optical modulators and photodetectors along with polymeric waveguides to transport the light. We use grayscale lithography to fabricate curved facets into the waveguides to couple light into the modulators and photodetectors. Next, at the chip-to-chip level in high-performance multiprocessor computing systems, communication distances vary from a few centimeters to tens of centimeters. An optical design for coupling light from off-chip lasers to on-chip surface-normal modulators is proposed in order to implement chip-to-chip free-space optical interconnects. The method uses a dual-prism module constructed from prisms made of two different glasses. The various alignment tolerances of the proposed system are investigated and found to be well within pick-and-place accuracies. For the off-chip lasers, vertical cavity surface emitting lasers (VCSELs) are proposed. The rationale behind using on-chip modulators rather than VCSELs is to avoid VCSEL thermal loads on chip, and because of higher reliability of modulators than VCSELs. Particularly above 10Gbps, an empirical model developed shows the rapid decrease of VCSEL median time to failure vs. data rate. Thus the proposed interconnect scheme which utilizes continuous wave VCSELs that are externally modulated by on-chip multiple quantum well modulators is applicable for chip-to-chip optical interconnects at 20Gbps and higher line data rates. Finally, for applications such as remote telemetry, where the interrogation distances can vary from a few meters to tens or even hundreds of meters we demonstrate a modulated retroreflector that utilizes InGaAs/InAlAs-based large-area multiple quantum well modulators on all three faces of a retroreflector. The large-area devices, fabricated by metalorganic chemical vapor deposition, are characterized in terms of the yield and leakage currents. A yield higher than that achieved previously using devices fabricated by molecular beam epitaxy is observed. The retroreflector module is constructed using standard FR4 printed circuit boards, thereby simplifying the wiring issue. A high optical contrast ratio of 8.23dB is observed for a drive of 20V. A free-standing PCB retroreflector is explored and found to have insufficient angular tolerances (+/-0.5 degrees). We show that the angular errors in the corner-cube construction can be corrected for using off-the-shelf optical components as opposed to mounting the PCBs on a precision corner cube, as has been done previously.

ATAMM enhancement and multiprocessor performance evaluation

NASA Technical Reports Server (NTRS)

Stoughton, John W.; Mielke, Roland R.; Som, Sukhamoy; Obando, Rodrigo; Malekpour, Mahyar R.; Jones, Robert L., III; Mandala, Brij Mohan V.

1991-01-01

ATAMM (Algorithm To Architecture Mapping Model) enhancement and multiprocessor performance evaluation is discussed. The following topics are included: the ATAMM model; ATAMM enhancement; ADM (Advanced Development Model) implementation of ATAMM; and ATAMM support tools.

Multiprocessor architectural study

NASA Technical Reports Server (NTRS)

Kosmala, A. L.; Stanten, S. F.; Vandever, W. H.

1972-01-01

An architectural design study was made of a multiprocessor computing system intended to meet functional and performance specifications appropriate to a manned space station application. Intermetrics, previous experience, and accumulated knowledge of the multiprocessor field is used to generate a baseline philosophy for the design of a future SUMC* multiprocessor. Interrupts are defined and the crucial questions of interrupt structure, such as processor selection and response time, are discussed. Memory hierarchy and performance is discussed extensively with particular attention to the design approach which utilizes a cache memory associated with each processor. The ability of an individual processor to approach its theoretical maximum performance is then analyzed in terms of a hit ratio. Memory management is envisioned as a virtual memory system implemented either through segmentation or paging. Addressing is discussed in terms of various register design adopted by current computers and those of advanced design.

Multiprocessor smalltalk: Implementation, performance, and analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pallas, J.I.

1990-01-01

Multiprocessor Smalltalk demonstrates the value of object-oriented programming on a multiprocessor. Its implementation and analysis shed light on three areas: concurrent programming in an object oriented language without special extensions, implementation techniques for adapting to multiprocessors, and performance factors in the resulting system. Adding parallelism to Smalltalk code is easy, because programs already use control abstractions like iterators. Smalltalk's basic control and concurrency primitives (lambda expressions, processes and semaphores) can be used to build parallel control abstractions, including parallel iterators, parallel objects, atomic objects, and futures. Language extensions for concurrency are not required. This implementation demonstrates that it is possiblemore » to build an efficient parallel object-oriented programming system and illustrates techniques for doing so. Three modification tools-serialization, replication, and reorganization-adapted the Berkeley Smalltalk interpreter to the Firefly multiprocessor. Multiprocessor Smalltalk's performance shows that the combination of multiprocessing and object-oriented programming can be effective: speedups (relative to the original serial version) exceed 2.0 for five processors on all the benchmarks; the median efficiency is 48%. Analysis shows both where performance is lost and how to improve and generalize the experimental results. Changes in the interpreter to support concurrency add at most 12% overhead; better access to per-process variables could eliminate much of that. Changes in the user code to express concurrency add as much as 70% overhead; this overhead could be reduced to 54% if blocks (lambda expressions) were reentrant. Performance is also lost when the program cannot keep all five processors busy.« less

The clinical and occupational effectiveness of condition management for Incapacity Benefit recipients.

PubMed

Kellett, Stephen; Bickerstaffe, Darren; Purdie, Fiona; Dyke, Andrew; Filer, Sarah; Lomax, Victoria; Tomlinson, Hayley

2011-06-01

OBJECTIVES. The aim of the Condition Management Programme (CMP) is to help Incapacity Benefit recipients manage their health conditions more effectively and return to work. This paper seeks to examine the clinical and employment outcomes from a group-based and mixed-condition CMP. DESIGN. In a prospective cohort design, measures of employment status and psychological well-being were taken at three time points; pre-CMP, post-CMP, and at 3-month follow-up. METHOD. Participants (N= 2,064) with a variety of physical and mental health conditions voluntarily attended a seven session cognitive-behaviourally informed psychoeducational group intervention. The psychological measures used were the Clinical Outcomes in Routine Evaluation - Outcome Measure, Work and Social Adjustment Scale, Self-Efficacy Scale, and the Intrinsic Motivation Scale. The employment status of participants was also measured at the three time points of the evaluation. RESULTS. Following CMP, 50% of participants experienced a reliable improvement in psychological well-being and 26% had either taken some steps towards work or returned to work at follow-up. Participants with a mental health condition were more likely to experience a reliable improvement in psychological well-being compared to those with physical health conditions. CONCLUSIONS. The results suggest that participation in CMP may be helpful in facilitating more effective self-management of the health conditions contributing to unemployment. The results have implications for whether formal employment assistance should be available in mental health services. ©2010 The British Psychological Society.

Cerebral misery perfusion due to carotid occlusive disease

PubMed Central

Maddula, Mohana; Sprigg, Nikola; Bath, Philip M; Munshi, Sunil

2017-01-01

Purpose Cerebral misery perfusion (CMP) is a condition where cerebral autoregulatory capacity is exhausted, and cerebral blood supply in insufficient to meet metabolic demand. We present an educational review of this important condition, which has a range of clinical manifestations. Method A non-systematic review of published literature was undertaken on CMP and major cerebral artery occlusive disease, using Pubmed and Sciencedirect. Findings Patients with CMP may present with strokes in watershed territories, collapses and transient ischaemic attacks or episodic movements associated with an orthostatic component. While positron emission tomography is the gold standard investigation for misery perfusion, advanced MRI is being increasingly used as an alternative investigation modality. The presence of CMP increases the risk of strokes. In addition to the devastating effect of stroke, there is accumulating evidence of impaired cognition and quality of life with carotid occlusive disease (COD) and misery perfusion. The evidence for revascularisation in the setting of complete carotid occlusion is weak. Medical management constitutes careful blood pressure management while addressing other vascular risk factors. Discussion The evidence for the management of patients with COD and CMP is discussed, together with recommendations based on our local experience. In this review, we focus on misery perfusion due to COD. Conclusion Patients with CMP and COD may present with a wide-ranging clinical phenotype and therefore to many specialties. Early identification of patients with misery perfusion may allow appropriate management and focus on strategies to maintain or improve cerebral blood flow, while avoiding potentially harmful treatment. PMID:28959496

Does the grading of chondromalacia patellae influence anterior knee pain following total knee arthroplasty without patellar resurfacing?

PubMed

Zha, Guo-Chun; Feng, Shuo; Chen, Xiang-Yang; Guo, Kai-Jin

2018-03-01

The influence of chondromalacia patellae (CMP) on post-operative anterior knee pain (AKP) following total knee arthroplasty (TKA) remains controversial, and few studies have focused on the relationship between them. The purpose of this study was to determine whether different CMP grades affect the incidence of AKP after TKA without patellar resurfacing. We performed a retrospective analysis of prospectively collected data on 290 TKAs with the use of the low contact stress mobile-bearing prosthesis, without patellar resurfacing in 290 patients from February 2009 to January 2013. Patients were assessed by the Outerbridge classification for CMP, visual analog scale for AKP, the Knee Society clinical scoring system of knee score (KS), function score (FS), the patellar score (PS) for clinical function, and patients' satisfaction. The intra-operative grading of CMP: grade I in 30 patients, grade II in 68 patients, grade III in 97 patients, and grade IV in 95 patients. The incidence of AKP at 36-month follow-up was 10.3% (30/290). No statistical difference was detected among the different CMP grades in terms of the incidence of AKP (p = 0.995), patients' satisfaction (p = 0.832), KS (p = 0.228), FS (p = 0.713), and PS (p = 0.119) at 36-month follow-up. The findings may suggest no relevant influence of CMP grading on the incidence of AKP after TKA without patellar resurfacing.

ECM turnover-stimulated gene delivery through collagen-mimetic peptide-plasmid integration in collagen.

PubMed

Urello, Morgan A; Kiick, Kristi L; Sullivan, Millicent O

2017-10-15

Gene therapies have great potential in regenerative medicine; however, clinical translation has been inhibited by low stability and limited transfection efficiencies. Herein, we incorporate collagen-mimetic peptide (CMP)-linked polyplexes in collagen scaffolds to increase DNA stability by up to 400% and enable tailorable in vivo transgene expression at 100-fold higher levels and 10-fold longer time periods. These improvements were directly linked to a sustained interaction between collagen and polyplexes that persisted during cellular remodeling, polyplex uptake, and intracellular trafficking. Specifically, incorporation of CMPs into polyethylenimine (PEI) polyplexes preserved serum-exposed polyplex-collagen activity over a period of 14days, with 4 orders-of-magnitude more intact DNA present in CMP-modified polyplex-collagen relative to unmodified polyplex-collagen after a 10day incubation under cell culture conditions. CMP-modification also altered endocytic uptake, as indicated by gene silencing studies showing a nearly 50% decrease in transgene expression in response to caveolin-1 silencing in modified samples versus only 30% in unmodified samples. Furthermore, cellular internalization studies demonstrated that polyplex-collagen association persisted within cells in CMP polyplexes, but not in unmodified polyplexes, suggesting that CMP linkage to collagen regulates intracellular transport. Moreover, experiments in an in vivo repair model showed that CMP modification enabled tailoring of transgene expression from 4 to 25days over a range of concentrations. Overall, these findings demonstrate that CMP decoration provides substantial improvements in gene retention, altered release kinetics, improved serum-stability, and improved gene activity in vivo. This versatile technique has great potential for multiple applications in regenerative medicine. In this work, we demonstrate a novel approach for stably integrating DNA into collagen scaffolds to exploit the natural process of collagen remodelling for high efficiency non-viral gene delivery. The incorporation of CMPs into DNA polyplexes, coupled with the innate affinity between CMPs and collagen, not only permitted improved control over polyplex retention and release, but also provided a series of substantial and highly unique benefits via the stable and persistent linkage between CMP-polyplexes and collagen fragments. Specifically, CMP-modification of polyplexes was demonstrated to (i) control release for nearly a month, (ii) improve vector stability under physiological-like conditions, and (iii) provide ligands able to efficiently transfer genes via endocytic collagen pathways. These unique properties overcome key barriers inhibiting non-viral gene therapy. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Cytosine to uracil conversion through hydrolytic deamination of cytidine monophosphate hydroxy-alkylated on the amino group: a liquid chromatography--electrospray ionization--mass spectrometry investigation.

PubMed

Losito, I; Angelico, R; Introna, B; Ceglie, A; Palmisano, F

2012-10-01

A novel pathway for cytosine to uracil conversion performed in a micellar environment, leading to the generation of uridine monophosphate (UMP), was evidenced during the alkylation reaction of cytidine monophosphate (CMP) by dodecyl epoxide. Liquid chromatography-electrospray ionization - ion trap - mass spectrometry was used to separate and identify the reaction products and to follow their formation over time. The detection of hydroxy-amino-dodecane, concurrently with free UMP, in the reaction mixture suggested that, among the various alkyl-derivatives formed, CMP alkylated on the amino group of cytosine could undergo tautomerization to an imine and hydrolytic deamination, generating UMP. Interestingly, no evidence for this peculiar conversion pathway was obtained when guanosine monophosphate (GMP), the complementary ribonucleotide of CMP, was also present in the reaction mixture, due to the fact that NH(2)-alkylated CMP was not formed in this case. The last finding emphasized the role played by CMP-GMP molecular interactions, mediated by a micellar environment, in hindering the alkylation reaction at the level of the cytosine amino group. Copyright © 2012 John Wiley & Sons, Ltd.

Deoxypyrimidine monophosphate bypass therapy for thymidine kinase 2 deficiency

PubMed Central

Garone, Caterina; Garcia-Diaz, Beatriz; Emmanuele, Valentina; Lopez, Luis C; Tadesse, Saba; Akman, Hasan O; Tanji, Kurenai; Quinzii, Catarina M; Hirano, Michio

2014-01-01

Autosomal recessive mutations in the thymidine kinase 2 gene (TK2) cause mitochondrial DNA depletion, multiple deletions, or both due to loss of TK2 enzyme activity and ensuing unbalanced deoxynucleotide triphosphate (dNTP) pools. To bypass Tk2 deficiency, we administered deoxycytidine and deoxythymidine monophosphates (dCMP+dTMP) to the Tk2 H126N (Tk2−/−) knock-in mouse model from postnatal day 4, when mutant mice are phenotypically normal, but biochemically affected. Assessment of 13-day-old Tk2−/− mice treated with dCMP+dTMP 200 mg/kg/day each (Tk2−/−200dCMP/dTMP) demonstrated that in mutant animals, the compounds raise dTTP concentrations, increase levels of mtDNA, ameliorate defects of mitochondrial respiratory chain enzymes, and significantly prolong their lifespan (34 days with treatment versus 13 days untreated). A second trial of dCMP+dTMP each at 400 mg/kg/day showed even greater phenotypic and biochemical improvements. In conclusion, dCMP/dTMP supplementation is the first effective pharmacologic treatment for Tk2 deficiency. Subject Categories Genetics, Gene Therapy & Genetic Disease; Metabolism PMID:24968719

Deoxypyrimidine monophosphate bypass therapy for thymidine kinase 2 deficiency.

PubMed

Garone, Caterina; Garcia-Diaz, Beatriz; Emmanuele, Valentina; Lopez, Luis C; Tadesse, Saba; Akman, Hasan O; Tanji, Kurenai; Quinzii, Catarina M; Hirano, Michio

2014-08-01

Autosomal recessive mutations in the thymidine kinase 2 gene (TK2) cause mitochondrial DNA depletion, multiple deletions, or both due to loss of TK2 enzyme activity and ensuing unbalanced deoxynucleotide triphosphate (dNTP) pools. To bypass Tk2 deficiency, we administered deoxycytidine and deoxythymidine monophosphates (dCMP+dTMP) to the Tk2 H126N (Tk2(-/-)) knock-in mouse model from postnatal day 4, when mutant mice are phenotypically normal, but biochemically affected. Assessment of 13-day-old Tk2(-/-) mice treated with dCMP+dTMP 200 mg/kg/day each (Tk2(-/-200dCMP/) (dTMP)) demonstrated that in mutant animals, the compounds raise dTTP concentrations, increase levels of mtDNA, ameliorate defects of mitochondrial respiratory chain enzymes, and significantly prolong their lifespan (34 days with treatment versus 13 days untreated). A second trial of dCMP+dTMP each at 400 mg/kg/day showed even greater phenotypic and biochemical improvements. In conclusion, dCMP/dTMP supplementation is the first effective pharmacologic treatment for Tk2 deficiency. © 2014 The Authors. Published under the terms of the CC BY 4.0 license.

Circulating cell-derived microparticles in women with pregnancy loss.

PubMed

Alijotas-Reig, Jaume; Palacio-Garcia, Carles; Farran-Codina, Immaculada; Zarzoso, Cristina; Cabero-Roura, Luis; Vilardell-Tarres, Miquel

2011-09-01

To analyze cell-derived microparticles (cMP) in pregnancy loss (PL), both recurrent miscarriages (RM) and unexplained fetal loss (UFL). Non-matched case-control study was performed at Vall d'Hebron Hospital. Cell-derived microparticles of 53 PL cases, 30 with RM, 16 with UFL, and 7 (RM + UFL), were compared to 38 healthy pregnant women. Twenty healthy non-pregnant women act as controls. Cell-derived microparticles were analyzed through flow cytometry. Results are given as total annexin (A5+), endothelial-(CD144+/CD31+ CD41-), platelet-(CD41+), leukocyte-(CD45+) and CD41- c-MP/μL of plasma. Antiphospholipid antibodies (aPLA) were analyzed according to established methods. Comparing PL versus healthy pregnant, we observed a significant endothelial cMP decrease in PL. When comparing RM subgroup with controls, we observed significant decreases in endothelial cMP. When comparing the PL positive for aPLA versus PL-aPLA-negative, no cMP numbering differences were seen. Pregnancy loss seems to be related to endothelial cell activation and/or consumption. A relationship between aPLA and cMP could not be demonstrated. © 2011 John Wiley & Sons A/S.

A fault-tolerant information processing concept for space vehicles.

NASA Technical Reports Server (NTRS)

Hopkins, A. L., Jr.

1971-01-01

A distributed fault-tolerant information processing system is proposed, comprising a central multiprocessor, dedicated local processors, and multiplexed input-output buses connecting them together. The processors in the multiprocessor are duplicated for error detection, which is felt to be less expensive than using coded redundancy of comparable effectiveness. Error recovery is made possible by a triplicated scratchpad memory in each processor. The main multiprocessor memory uses replicated memory for error detection and correction. Local processors use any of three conventional redundancy techniques: voting, duplex pairs with backup, and duplex pairs in independent subsystems.

Cache-based error recovery for shared memory multiprocessor systems

NASA Technical Reports Server (NTRS)

Wu, Kun-Lung; Fuchs, W. Kent; Patel, Janak H.

1989-01-01

A multiprocessor cache-based checkpointing and recovery scheme for of recovering from transient processor errors in a shared-memory multiprocessor with private caches is presented. New implementation techniques that use checkpoint identifiers and recovery stacks to reduce performance degradation in processor utilization during normal execution are examined. This cache-based checkpointing technique prevents rollback propagation, provides for rapid recovery, and can be integrated into standard cache coherence protocols. An analytical model is used to estimate the relative performance of the scheme during normal execution. Extensions that take error latency into account are presented.

Novel technique for fabrication of multi-layered microcoils in microelectromechanical systems (MEMS) applications

NASA Astrophysics Data System (ADS)

Chang, Hung-Pin; Qian, Jiangyuan; Bachman, Mark; Congdon, Philip; Li, Guann-pyng

2002-07-01

A novel planarization technique, compressive molding planarization (CMP) is developed for implementation of a multi-layered micro coil device. Applying CMP and other micromachining techniques, a multi-layered micro coil device has been designed and fabricated, and its use in the magnetic micro actuators for hard disk drive applications has been demonstrated, showing that it can produce milli-Newton of magnetic force suitable for driving a micro actuator. The novel CMP technique can be equally applicable in other MEMS devices fabrication to ease the process integration for the complicated structure.

Antifungal nanofibers made by controlled release of sea animal derived peptide

NASA Astrophysics Data System (ADS)

Viana, Juliane F. C.; Carrijo, Jéssica; Freitas, Camila G.; Paul, Arghya; Alcaraz, Jarib; Lacorte, Cristiano C.; Migliolo, Ludovico; Andrade, César A.; Falcão, Rosana; Santos, Nuno C.; Gonçalves, Sónia; Otero-González, Anselmo J.; Khademhosseini, Ali; Dias, Simoni C.; Franco, Octávio L.

2015-03-01

Candida albicans is a common human-pathogenic fungal species with the ability to cause several diseases including surface infections. Despite the clear difficulties of Candida control, antimicrobial peptides (AMPs) have emerged as an alternative strategy for fungal control. In this report, different concentrations of antifungal Cm-p1 (Cencritchis muricatus peptide 1) were electrospun into nanofibers for drug delivery. The nanofibers were characterized by mass spectrometry confirming the presence of the peptide on the scaffold. Atomic force microscopy and scanning electronic microscopy were used to measure the diameters, showing that Cm-p1 affects fiber morphology as well as the diameter and scaffold thickness. The Cm-p1 release behavior from the nanofibers demonstrated peptide release from 30 min to three days, leading to effective yeast control in the first 24 hours. Moreover, the biocompatibility of the fibers were evaluated through a MTS assay as well as ROS production by using a HUVEC model, showing that the fibers do not affect cell viability and only nanofibers containing 10% Cm-p1-PVA improved ROS generation. In addition, the secretion of pro-inflammatory cytokines IL-6 and TNF-α by the HUVECs was also slightly modified by the 10% Cm-p1-PVA nanofibers. In conclusion, the electrospinning technique applied here allowed for the manufacture of biodegradable biomimetic nanofibrous extracellular membranes with the ability to control fungal infection.Candida albicans is a common human-pathogenic fungal species with the ability to cause several diseases including surface infections. Despite the clear difficulties of Candida control, antimicrobial peptides (AMPs) have emerged as an alternative strategy for fungal control. In this report, different concentrations of antifungal Cm-p1 (Cencritchis muricatus peptide 1) were electrospun into nanofibers for drug delivery. The nanofibers were characterized by mass spectrometry confirming the presence of the peptide on the scaffold. Atomic force microscopy and scanning electronic microscopy were used to measure the diameters, showing that Cm-p1 affects fiber morphology as well as the diameter and scaffold thickness. The Cm-p1 release behavior from the nanofibers demonstrated peptide release from 30 min to three days, leading to effective yeast control in the first 24 hours. Moreover, the biocompatibility of the fibers were evaluated through a MTS assay as well as ROS production by using a HUVEC model, showing that the fibers do not affect cell viability and only nanofibers containing 10% Cm-p1-PVA improved ROS generation. In addition, the secretion of pro-inflammatory cytokines IL-6 and TNF-α by the HUVECs was also slightly modified by the 10% Cm-p1-PVA nanofibers. In conclusion, the electrospinning technique applied here allowed for the manufacture of biodegradable biomimetic nanofibrous extracellular membranes with the ability to control fungal infection. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr00767d

Random or predictable?: Adoption patterns of chronic care management practices in physician organizations.

PubMed

Miake-Lye, Isomi M; Chuang, Emmeline; Rodriguez, Hector P; Kominski, Gerald F; Yano, Elizabeth M; Shortell, Stephen M

2017-08-24

Theories, models, and frameworks used by implementation science, including Diffusion of Innovations, tend to focus on the adoption of one innovation, when often organizations may be facing multiple simultaneous adoption decisions. For instance, despite evidence that care management practices (CMPs) are helpful in managing chronic illness, there is still uneven adoption by physician organizations. This exploratory paper leverages this natural variation in uptake to describe inter-organizational patterns in adoption of CMPs and to better understand how adoption choices may be related to one another. We assessed a cross section of national survey data from physician organizations reporting on the use of 20 CMPs (5 each for asthma, congestive heart failure, depression, and diabetes). Item response theory was used to explore patterns in adoption, first considering all 20 CMPs together and then by subsets according to disease focus or CMP type (e.g., registries, patient reminders). Mokken scale analysis explored whether adoption choices were linked by disease focus or CMP type and whether a consistent ordering of adoption choices was present. The Mokken scale for all 20 CMPs demonstrated medium scalability (H = 0.43), but no consistent ordering. Scales for subsets of CMPs sharing a disease focus had medium scalability (0.4 < H < 0.5), while subsets sharing a CMP type had strong scalability (H > 0.5). Scales for CMP type consistently ranked diabetes CMPs as most adoptable and depression CMPs as least adoptable. Within disease focus scales, patient reminders were ranked as the most adoptable CMP, while clinician feedback and patient education were ranked the least adoptable. Patterns of adoption indicate that innovation characteristics may influence adoption. CMP dissemination efforts may be strengthened by encouraging traditionally non-adopting organizations to focus on more adoptable practices first and then describing a pathway for the adoption of subsequent CMPs. Clarifying why certain CMPs are "less adoptable" may also provide insights into how to overcome CMP adoption constraints.

Carboxymethyl pachyman (CMP) reduces intestinal mucositis and regulates the intestinal microflora in 5-fluorouracil-treated CT26 tumour-bearing mice.

PubMed

Wang, Canhong; Yang, Shuxian; Gao, Li; Wang, Lili; Cao, Li

2018-05-23

The compound 5-fluorouracil (5-FU) is the first choice chemotherapeutic agent for the treatment of colorectal cancer (CRC), but intestinal mucositis is a primary limiting factor in anticancer therapy. There is currently no broadly effective targeted treatment to cure this side effect. Carboxymethylated pachyman (CMP) is a polysaccharide that is modified from the structure of pachyman isolated from Poria cocos (Chinese name: Fu Ling). Meanwhile, recent studies have shown that CMP exhibits immune regulatory, anti-inflammatory and antioxidant activities. Therefore, the purpose of this study was to evaluate the intestinal protective effect of CMP in 5-FU-treated CT26 tumour-bearing mice and to further explore its underlying mechanism(s) of action. Initially, a CT26 colon carcinoma xenograft mice model was established. The colon length, colon tissue injury, intestinal flora, short-chain fatty acids (SCFAs) and indicators linked to inflammation, antioxidation and apoptosis were then measured. Our results showed that CMP in combination with 5-FU reversed intestinal shortening (p < 0.01) and alleviated 5-FU-induced colon injury (p < 0.001) via suppression of ROS production; increasing the levels of CAT, GSH-Px and GSH; decreasing expression of NF-κB, p-p38 and Bax; and elevating the levels of Nrf2 and Bcl-2. More importantly, CMP had a significant impact and counteracted the intestinal microflora disorders produced by 5-FU by increasing the proportion of Bacteroidetes, lactobacilli, and butyric acid-producing and acetic acid-producing bacteria and restoring the intestinal flora diversity. Overall, this work suggested that CMP could regulate the ecological balance of the intestinal flora and reduce colon injuries induced by 5-FU in CT26 tumour-bearing mice, and the mechanism involved may be associated with the regulation of the NF-κB, Nrf2-ARE and MAPK/P38 pathways.

The Galley Parallel File System

NASA Technical Reports Server (NTRS)

Nieuwejaar, Nils; Kotz, David

1996-01-01

Most current multiprocessor file systems are designed to use multiple disks in parallel, using the high aggregate bandwidth to meet the growing I/0 requirements of parallel scientific applications. Many multiprocessor file systems provide applications with a conventional Unix-like interface, allowing the application to access multiple disks transparently. This interface conceals the parallelism within the file system, increasing the ease of programmability, but making it difficult or impossible for sophisticated programmers and libraries to use knowledge about their I/O needs to exploit that parallelism. In addition to providing an insufficient interface, most current multiprocessor file systems are optimized for a different workload than they are being asked to support. We introduce Galley, a new parallel file system that is intended to efficiently support realistic scientific multiprocessor workloads. We discuss Galley's file structure and application interface, as well as the performance advantages offered by that interface.

Mapping of H.264 decoding on a multiprocessor architecture

NASA Astrophysics Data System (ADS)

van der Tol, Erik B.; Jaspers, Egbert G.; Gelderblom, Rob H.

2003-05-01

Due to the increasing significance of development costs in the competitive domain of high-volume consumer electronics, generic solutions are required to enable reuse of the design effort and to increase the potential market volume. As a result from this, Systems-on-Chip (SoCs) contain a growing amount of fully programmable media processing devices as opposed to application-specific systems, which offered the most attractive solutions due to a high performance density. The following motivates this trend. First, SoCs are increasingly dominated by their communication infrastructure and embedded memory, thereby making the cost of the functional units less significant. Moreover, the continuously growing design costs require generic solutions that can be applied over a broad product range. Hence, powerful programmable SoCs are becoming increasingly attractive. However, to enable power-efficient designs, that are also scalable over the advancing VLSI technology, parallelism should be fully exploited. Both task-level and instruction-level parallelism can be provided by means of e.g. a VLIW multiprocessor architecture. To provide the above-mentioned scalability, we propose to partition the data over the processors, instead of traditional functional partitioning. An advantage of this approach is the inherent locality of data, which is extremely important for communication-efficient software implementations. Consequently, a software implementation is discussed, enabling e.g. SD resolution H.264 decoding with a two-processor architecture, whereas High-Definition (HD) decoding can be achieved with an eight-processor system, executing the same software. Experimental results show that the data communication considerably reduces up to 65% directly improving the overall performance. Apart from considerable improvement in memory bandwidth, this novel concept of partitioning offers a natural approach for optimally balancing the load of all processors, thereby further improving the overall speedup.

Statistical metrology—measurement and modeling of variation for advanced process development and design rule generation

NASA Astrophysics Data System (ADS)

Boning, Duane S.; Chung, James E.

1998-11-01

Advanced process technology will require more detailed understanding and tighter control of variation in devices and interconnects. The purpose of statistical metrology is to provide methods to measure and characterize variation, to model systematic and random components of that variation, and to understand the impact of variation on both yield and performance of advanced circuits. Of particular concern are spatial or pattern-dependencies within individual chips; such systematic variation within the chip can have a much larger impact on performance than wafer-level random variation. Statistical metrology methods will play an important role in the creation of design rules for advanced technologies. For example, a key issue in multilayer interconnect is the uniformity of interlevel dielectric (ILD) thickness within the chip. For the case of ILD thickness, we describe phases of statistical metrology development and application to understanding and modeling thickness variation arising from chemical-mechanical polishing (CMP). These phases include screening experiments including design of test structures and test masks to gather electrical or optical data, techniques for statistical decomposition and analysis of the data, and approaches to calibrating empirical and physical variation models. These models can be integrated with circuit CAD tools to evaluate different process integration or design rule strategies. One focus for the generation of interconnect design rules are guidelines for the use of "dummy fill" or "metal fill" to improve the uniformity of underlying metal density and thus improve the uniformity of oxide thickness within the die. Trade-offs that can be evaluated via statistical metrology include the improvements to uniformity possible versus the effect of increased capacitance due to additional metal.

Conjugated Microporous Polymers for Heterogeneous Catalysis.

PubMed

Zhou, Yun-Bing; Zhan, Zhuang-Ping

2018-01-04

Conjugated microporous polymers (CMPs) are a class of crosslinked polymers that combine permanent micropores with π-conjugated skeletons and possess three-dimensional (3D) networks. Compared with conventional materials such as metal-organic frameworks (MOFs) and covalent organic frameworks (COFs), CMPs usually have superior chemical and thermal stability. CMPs have made significant progress in heterogeneous catalysis in the past seven years. With a bottom-up strategy, catalytic moieties can be directly introduced into in the framework to produce heterogeneous CMP catalysts. Higher activity, stability, and selectivity can be obtained with heterogeneous CMP catalysts in comparison with their homogeneous analogs. In addition, CMP catalysts can be easily isolated and recycled. In this review, we focus on CMPs as an intriguing platform for developing various highly efficient and recyclable heterogeneous catalysts in organic reactions. The design, synthesis, and structure of these CMP catalysts are also discussed in this focus review. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

TreeCmp: Comparison of Trees in Polynomial Time

PubMed Central

Bogdanowicz, Damian; Giaro, Krzysztof; Wróbel, Borys

2012-01-01

When a phylogenetic reconstruction does not result in one tree but in several, tree metrics permit finding out how far the reconstructed trees are from one another. They also permit to assess the accuracy of a reconstruction if a true tree is known. TreeCmp implements eight metrics that can be calculated in polynomial time for arbitrary (not only bifurcating) trees: four for unrooted (Matching Split metric, which we have recently proposed, Robinson-Foulds, Path Difference, Quartet) and four for rooted trees (Matching Cluster, Robinson-Foulds cluster, Nodal Splitted and Triple). TreeCmp is the first implementation of Matching Split/Cluster metrics and the first efficient and convenient implementation of Nodal Splitted. It allows to compare relatively large trees. We provide an example of the application of TreeCmp to compare the accuracy of ten approaches to phylogenetic reconstruction with trees up to 5000 external nodes, using a measure of accuracy based on normalized similarity between trees.

The endolysins of bacteriophages CMP1 and CN77 are specific for the lysis of Clavibacter michiganensis strains.

PubMed

Wittmann, Johannes; Eichenlaub, Rudolf; Dreiseikelmann, Brigitte

2010-08-01

Putative endolysin genes of bacteriophages CMP1 and CN77, which infect Clavibacter michiganensis subsp. michiganensis and C. michiganensis subsp. nebraskensis, respectively, were cloned and expressed in Escherichia coli. The His-tagged endolysin of CMP1 consists of 306 amino acids and has a calculated molecular mass of 34.8 kDa, while the His-tagged endolysin of CN77 has 290 amino acids with a molecular mass of 31.9 kDa. The proteins were purified and their bacteriolytic activity was demonstrated. The bacteriolytic activity of both enzymes showed a host range which was limited to the respective C. michiganensis subspecies and did not affect other bacteria, even those closely related to Clavibacter. Due to the high specificity of the CMP1 and CN77 endolysins they may be useful tools for biocontrol of plant-pathogenic C. michiganensis without affecting other bacteria in the soil.

Interaction of cytidine 5'-monophosphate with Au(111): an in situ infrared spectroscopic study.

PubMed

Doneux, Thomas; Fojt, Lukás

2009-07-13

The interaction of cytidine 5'-monophosphate (CMP) with gold surfaces is studied by means of in situ infrared spectroscopy and cyclic voltammetry at the Au(111)|aqueous solution interface. Similar to other nucleic acid components, cytidine 5'-monophosphate is chemisorbed on the surface at positive potentials, and the amount of adsorbed CMP increases with the potential. Subtractively normalized interfacial Fourier-transform infrared spectroscopy (SNIFTIRS) is used to identify the adsorbed and desorbed species. Upon electrochemical desorption, the molecules released in solution are unprotonated on the N3 atom. Striking similarities are found between the spectrum of adsorbed CMP and the solution spectrum of protonated CMP. The origin of such similarities is discussed. The results strongly suggest that chemisorption occurs through the N3 atom of the pyrimidine ring. A comparison is drawn with cytidine, whose electrochemical and spectroscopic behaviors are also investigated.

Ultrafast fingerprint indexing for embedded systems

NASA Astrophysics Data System (ADS)

Zhou, Ru; Sin, Sang Woo; Li, Dongju; Isshiki, Tsuyoshi; Kunieda, Hiroaki

2011-10-01

A novel core-based fingerprint indexing scheme for embedded systems is presented in this paper. Our approach is enabled by our new precise and fast core-detection algorithm with the direction map. It introduces the feature of CMP (core minutiae pair), which describes the coordinates of minutiae and the direction of ridges associated with the minutiae based on the uniquely defined core coordinates. Since each CMP is identical against the shift and rotation of the fingerprint image, the CMP comparison between a template and an input image can be performed without any alignment. The proposed indexing algorithm based on CMP is suitable for embedded systems because the tremendous speed up and the memory reduction are achieved. In fact, the experiments with the fingerprint database FVC2002 show that its speed for the identifications becomes about 40 times faster than conventional approaches, even though the database includes fingerprints with no core.

Two-dimensional systolic-array architecture for pixel-level vision tasks

NASA Astrophysics Data System (ADS)

Vijverberg, Julien A.; de With, Peter H. N.

2010-05-01

This paper presents ongoing work on the design of a two-dimensional (2D) systolic array for image processing. This component is designed to operate on a multi-processor system-on-chip. In contrast with other 2D systolic-array architectures and many other hardware accelerators, we investigate the applicability of executing multiple tasks in a time-interleaved fashion on the Systolic Array (SA). This leads to a lower external memory bandwidth and better load balancing of the tasks on the different processing tiles. To enable the interleaving of tasks, we add a shadow-state register for fast task switching. To reduce the number of accesses to the external memory, we propose to share the communication assist between consecutive tasks. A preliminary, non-functional version of the SA has been synthesized for an XV4S25 FPGA device and yields a maximum clock frequency of 150 MHz requiring 1,447 slices and 5 memory blocks. Mapping tasks from video content-analysis applications from literature on the SA yields reductions in the execution time of 1-2 orders of magnitude compared to the software implementation. We conclude that the choice for an SA architecture is useful, but a scaled version of the SA featuring less logic with fewer processing and pipeline stages yielding a lower clock frequency, would be sufficient for a video analysis system-on-chip.

A nano-scale mirror-like surface of Ti-6Al-4V attained by chemical mechanical polishing

NASA Astrophysics Data System (ADS)

Chenliang, Liang; Weili, Liu; Shasha, Li; Hui, Kong; Zefang, Zhang; Zhitang, Song

2016-05-01

Metal Ti and its alloys have been widely utilized in the fields of aviation, medical science, and micro-electro-mechanical systems, for its excellent specific strength, resistance to corrosion, and biological compatibility. As the application of Ti moves to the micro or nano scale, however, traditional methods of planarization have shown their short slabs. Thus, we introduce the method of chemical mechanical polishing (CMP) to provide a new way for the nano-scale planarization method of Ti alloys. We obtain a mirror-like surface, whose flatness is of nano-scale, via the CMP method. We test the basic mechanical behavior of Ti-6Al-4V (Ti64) in the CMP process, and optimize the composition of CMP slurry. Furthermore, the possible reactions that may take place in the CMP process have been studied by electrochemical methods combined with x-ray photoelectron spectroscopy (XPS). An equivalent circuit has been built to interpret the dynamic of oxidation. Finally, a model has been established to explain the synergy of chemical and mechanical effects in the CMP of Ti-6Al-4V. Project supported by the National Major Scientific and Technological Special Project during the Twelfth Five-year Plan Period of China (Grant No. 2009ZX02030-1), the National Natural Science Foundation of China (Grant No. 51205387), the Support by Science and Technology Commission of Shanghai City, China (Grant No. 11nm0500300), and the Science and Technology Commission of Shanghai City, China (Grant No. 14XD1425300).

The Effect of Postpartum Depression and Current Mental Health Problems of the Mother on Child Behaviour at Eight Years.

PubMed

Closa-Monasterolo, R; Gispert-Llaurado, M; Canals, J; Luque, V; Zaragoza-Jordana, M; Koletzko, B; Grote, V; Weber, M; Gruszfeld, D; Szott, K; Verduci, E; ReDionigi, A; Hoyos, J; Brasselle, G; Escribano Subías, J

2017-07-01

Background Maternal postpartum depression (PPD) could affect children's emotional development, increasing later risk of child psychological problems. The aim of our study was to assess the association between child's emotional and behavioural problems and mother's PPD, considering maternal current mental health problems (CMP). Methods This is a secondary analysis from the EU-Childhood Obesity Project (NCT00338689). Women completed the Edinburgh Postnatal Depression Scale (EPDS) at, 2, 3 and 6 months after delivery and the General Health Questionnaire (GHQ-12) to assess CMP once the children reached the age of 8 years. EPDS scores > 10 were defined as PPD and GHQ-12 scores > 2 were defined as CMP. The psychological problems of the children at the age of eight were collected by mothers through the Child's Behaviour Checklist (CBCL). Results 473, 474 and 459 mothers filled in GHQ-12 and CBCL tests at 8 years and EPDS at 2, 3 and 6 months, respectively. Anxiety and depression was significantly increased by maternal EPDS. Children whose mothers had both PPD and CMP exhibited the highest levels of psychological problems, followed by those whose mothers who had only CMP and only PPD. PPD and CMP had a significant effect on child's total psychological problems (p = 0.033, p < 0.001, respectively). Children whose mothers had PPD did not differ from children whose mothers did not have any depression. Conclusions Maternal postpartum depression and current mental health problems, separately and synergistically, increase children's psychological problems at 8 years.

Large Cardiac Muscle Patches Engineered From Human Induced-Pluripotent Stem Cell-Derived Cardiac Cells Improve Recovery From Myocardial Infarction in Swine.

PubMed

Gao, Ling; Gregorich, Zachery R; Zhu, Wuqiang; Mattapally, Saidulu; Oduk, Yasin; Lou, Xi; Kannappan, Ramaswamy; Borovjagin, Anton V; Walcott, Gregory P; Pollard, Andrew E; Fast, Vladimir G; Hu, Xinyang; Lloyd, Steven G; Ge, Ying; Zhang, Jianyi

2018-04-17

Here, we generated human cardiac muscle patches (hCMPs) of clinically relevant dimensions (4 cm × 2 cm × 1.25 mm) by suspending cardiomyocytes, smooth muscle cells, and endothelial cells that had been differentiated from human induced-pluripotent stem cells in a fibrin scaffold and then culturing the construct on a dynamic (rocking) platform. In vitro assessments of hCMPs suggest maturation in response to dynamic culture stimulation. In vivo assessments were conducted in a porcine model of myocardial infarction (MI). Animal groups included: MI hearts treated with 2 hCMPs (MI+hCMP, n=13), MI hearts treated with 2 cell-free open fibrin patches (n=14), or MI hearts with neither experimental patch (n=15); a fourth group of animals underwent sham surgery (Sham, n=8). Cardiac function and infarct size were evaluated by MRI, arrhythmia incidence by implanted loop recorders, and the engraftment rate by calculation of quantitative polymerase chain reaction measurements of expression of the human Y chromosome. Additional studies examined the myocardial protein expression profile changes and potential mechanisms of action that related to exosomes from the cell patch. The hCMPs began to beat synchronously within 1 day of fabrication, and after 7 days of dynamic culture stimulation, in vitro assessments indicated the mechanisms related to the improvements in electronic mechanical coupling, calcium-handling, and force generation, suggesting a maturation process during the dynamic culture. The engraftment rate was 10.9±1.8% at 4 weeks after the transplantation. The hCMP transplantation was associated with significant improvements in left ventricular function, infarct size, myocardial wall stress, myocardial hypertrophy, and reduced apoptosis in the periscar boarder zone myocardium. hCMP transplantation also reversed some MI-associated changes in sarcomeric regulatory protein phosphorylation. The exosomes released from the hCMP appeared to have cytoprotective properties that improved cardiomyocyte survival. We have fabricated a clinically relevant size of hCMP with trilineage cardiac cells derived from human induced-pluripotent stem cells. The hCMP matures in vitro during 7 days of dynamic culture. Transplantation of this type of hCMP results in significantly reduced infarct size and improvements in cardiac function that are associated with reduction in left ventricular wall stress. The hCMP treatment is not associated with significant changes in arrhythmogenicity. © 2017 American Heart Association, Inc.

Colloidal and electrochemical aspects of copper-CMP

NASA Astrophysics Data System (ADS)

Sun, Yuxia

Copper based interconnects with low dielectric constant layers are currently used to increase interconnect densities and reduce interconnect time delays in integrated circuits. The technology used to develop copper interconnects involves Chemical Mechanical Planarization (CMP) of copper films deposited on low-k layers (silica or silica based films), which is carried out using slurries containing abrasive particles. One issue using such a structure is copper contamination over dielectric layers (SiO2 film), if not reduced, this contamination will cause current leakage. In this study, the conditions conducive to copper contamination onto SiO2 films during Cu-CMP process were studied, and a post-CMP cleaning technique was discussed based on experimental results. It was found that the adsorption of copper onto a silica surface is kinetically fast (<0.5 minute). The amount of copper absorbed is pH and concentration dependent and affected by presence of H2O2, complexing agents, and copper corrosion inhibitor Benzotrazole. Based on de-sorption results, DI water alone was unable to reduce adsorbed copper to an acceptable level, especially for adsorption that takes place at a higher pH condition. The addition of complex agent, citric acid, proved effective in suppressing copper adsorption onto oxide silica during polishing or post-CMP cleaning by forming stable copper-CA complexes. Surface Complexation Modeling was used to simulate copper adsorption isotherms and predict the copper contamination levels on SiO2 surfaces. Another issue with the application of copper CMP is its environmental impact. CMP is a costly process due to its huge consumption of pure water and slurry. Additionally, Cu-CMP processing generates a waste stream containing certain amounts of copper and abrasive slurry particles. In this study, the separation technique electrocoagulation was investigated to remove both copper and abrasive slurry particles simultaneously. For effluent containing ˜40 ppm dissolved copper, it was found that ˜90% dissolved copper was removed from the waste streams through electroplating and in-situ chemical precipitation. The amount of copper removed through plating is impacted by membrane surface charge, type/amount of complexing agents, and solid content in the slurry suspension. The slurry particles can be removed ˜90% within 2 hours of EC through multiple mechanisms.

Preliminary basic performance analysis of the Cedar multiprocessor memory system

NASA Technical Reports Server (NTRS)

Gallivan, K.; Jalby, W.; Turner, S.; Veidenbaum, A.; Wijshoff, H.

1991-01-01

Some preliminary basic results on the performance of the Cedar multiprocessor memory system are presented. Empirical results are presented and used to calibrate a memory system simulator which is then used to discuss the scalability of the system.

Real-Time Multiprocessor Programming Language (RTMPL) user's manual

NASA Technical Reports Server (NTRS)

Arpasi, D. J.

1985-01-01

A real-time multiprocessor programming language (RTMPL) has been developed to provide for high-order programming of real-time simulations on systems of distributed computers. RTMPL is a structured, engineering-oriented language. The RTMPL utility supports a variety of multiprocessor configurations and types by generating assembly language programs according to user-specified targeting information. Many programming functions are assumed by the utility (e.g., data transfer and scaling) to reduce the programming chore. This manual describes RTMPL from a user's viewpoint. Source generation, applications, utility operation, and utility output are detailed. An example simulation is generated to illustrate many RTMPL features.

Validation of fault-free behavior of a reliable multiprocessor system - FTMP: A case study. [Fault-Tolerant Multi-Processor avionics

NASA Technical Reports Server (NTRS)

Clune, E.; Segall, Z.; Siewiorek, D.

1984-01-01

A program of experiments has been conducted at NASA-Langley to test the fault-free performance of a Fault-Tolerant Multiprocessor (FTMP) avionics system for next-generation aircraft. Baseline measurements of an operating FTMP system were obtained with respect to the following parameters: instruction execution time, frame size, and the variation of clock ticks. The mechanisms of frame stretching were also investigated. The experimental results are summarized in a table. Areas of interest for future tests are identified, with emphasis given to the implementation of a synthetic workload generation mechanism on FTMP.

Techniques for video compression

NASA Technical Reports Server (NTRS)

Wu, Chwan-Hwa

1995-01-01

In this report, we present our study on multiprocessor implementation of a MPEG2 encoding algorithm. First, we compare two approaches to implementing video standards, VLSI technology and multiprocessor processing, in terms of design complexity, applications, and cost. Then we evaluate the functional modules of MPEG2 encoding process in terms of their computation time. Two crucial modules are identified based on this evaluation. Then we present our experimental study on the multiprocessor implementation of the two crucial modules. Data partitioning is used for job assignment. Experimental results show that high speedup ratio and good scalability can be achieved by using this kind of job assignment strategy.

Preparation of chitosan/MCM-41-PAA nanocomposites and the adsorption behaviour of Hg(II) ions

NASA Astrophysics Data System (ADS)

Fu, Yong; Huang, Yue; Hu, Jianshe

2018-03-01

A novel functional hybrid mesoporous composite material (CMP) based on chitosan and MCM-41-PAA was reported and its application as an excellent adsorbent for Hg(II) ions was also investigated. Innovatively, MCM-41-PAA was prepared by using diatomite and polyacrylic acid (PAA) with integrated polymer-silica hybrid frameworks, and then CMP was fabricated by introducing MCM-41-PAA to chitosan using glutaraldehyde as a cross-linking agent. The structure and morphology of CMP were characterized by X-ray diffraction, Fourier transform infrared spectra, thermogravimetric analysis, scanning electron microscopy and Brunauer-Emmett-Teller measurements. The results showed that the CMP possessed multifunctional groups such as -OH, -COOH and -NH2 with large specific surface area. Adsorption behaviour of Hg(II) ions onto CMP was fitted better by the pseudo-second-order kinetic model and the Langmuir model when the initial Hg(II) concentration, pH, adsorption temperature and time were 200 mg l-1, 4, 298 K and 120 min, respectively, as the optimum conditions. The corresponding maximum adsorption capacity could reach 164 mg g-1. According to the thermodynamic parameters determined such as free energy, enthalpy and entropy, the adsorption process of Hg(II) ions was spontaneous endothermic adsorption.

Deoxycytidine and deoxythymidine treatment for thymidine kinase 2 deficiency

PubMed Central

Lopez-Gomez, Carlos; Levy, Rebecca J; Sanchez-Quintero, Maria J; Juanola-Falgarona, Marti; Barca, Emanuele; Garcia-Diaz, Beatriz; Tadesse, Saba; Garone, Caterina; Hirano, Michio

2017-01-01

Objective Thymidine kinase 2 (TK2), a critical enzyme in the mitochondrial pyrimidine salvage pathway, is essential for mitochondrial DNA (mtDNA) maintenance. Mutations in the nuclear gene TK2 cause TK2 deficiency, which manifests predominantly in children as myopathy with mtDNA depletion. Molecular bypass therapy with the TK2 products, dCMP and dTMP, prolongs the lifespan of Tk2-deficient (Tk2-/-) mice by 2-3 fold. Because we observed rapid catabolism of the deoxynucleoside monophosphates to deoxythymidine (dT) and deoxycytidine (dC), we hypothesized that: 1) deoxynucleosides might be the major active agents and 2) inhibition of deoxycytidine deamination might enhance dTMP+dCMP therapy. Methods To test these hypotheses, we assessed two therapies in Tk2-/- mice: 1) dT+dC and 2) co-administration of the deaminase inhibitor, tetrahydrouridine (THU), with dTMP+dCMP. Results We observed that dC+dT delayed disease onset, prolonged lifespan of Tk2-deficient mice, and restored mtDNA copy number as well as respiratory chain enzyme activities and levels. In contrast, dCMP+dTMP+THU therapy decreased lifespan of Tk2-/- animals compared to dCMP+dTMP. Interpretation Our studies demonstrate that deoxynucleoside substrate enhancement is a novel therapy, which may ameliorate TK2 deficiency in patients. PMID:28318037

Preparation of chitosan/MCM-41-PAA nanocomposites and the adsorption behaviour of Hg(II) ions

PubMed Central

Fu, Yong; Huang, Yue; Hu, Jianshe

2018-01-01

A novel functional hybrid mesoporous composite material (CMP) based on chitosan and MCM-41-PAA was reported and its application as an excellent adsorbent for Hg(II) ions was also investigated. Innovatively, MCM-41-PAA was prepared by using diatomite and polyacrylic acid (PAA) with integrated polymer–silica hybrid frameworks, and then CMP was fabricated by introducing MCM-41-PAA to chitosan using glutaraldehyde as a cross-linking agent. The structure and morphology of CMP were characterized by X-ray diffraction, Fourier transform infrared spectra, thermogravimetric analysis, scanning electron microscopy and Brunauer–Emmett–Teller measurements. The results showed that the CMP possessed multifunctional groups such as –OH, –COOH and –NH2 with large specific surface area. Adsorption behaviour of Hg(II) ions onto CMP was fitted better by the pseudo-second-order kinetic model and the Langmuir model when the initial Hg(II) concentration, pH, adsorption temperature and time were 200 mg l−1, 4, 298 K and 120 min, respectively, as the optimum conditions. The corresponding maximum adsorption capacity could reach 164 mg g−1. According to the thermodynamic parameters determined such as free energy, enthalpy and entropy, the adsorption process of Hg(II) ions was spontaneous endothermic adsorption. PMID:29657793

Chemical-mechanical planarization of aluminum and copper interconnects with magnetic liners

NASA Astrophysics Data System (ADS)

Wang, Bin

2000-10-01

Chemical Mechanical Planarization (CMP) has been employed to achieve Damascene patterning of aluminum and copper interconnects with unique magnetic liners. A one-step process was developed for each interconnect scheme, using a double-layered pad with mesh cells, pores, and perforations on a top hard layer. In a hydrogen peroxide-based slurry, aluminum CMP was a process of periodic removal and formation of a surface oxide layer. Cu CMP in the same slurry, however, was found to be a dissolution dominant process. In a potassium iodate-based slurry, copper removal was the result of two competing reactions: copper dissolution and a non-native surface layer formation. Guided by electrochemistry, slurries were developed to remove nickel in different regimes of the corrosion kinetics diagram. Nickel CMP in a ferric sulfate-based slurry resulted in periodic removal and formation of a passive surface layer. In a potassium permanganate-based slurry, nickel removal is a dissolution dominant process. Visible Al(Cu) surface damages obtained with copper-doped aluminum could be eliminated by understanding the interactions between the substrate, the pad, and the abrasive agglomerate. Increasing substrate hardness by annealing prior to CMP led to a surface finish free of visible scratches. A similar result was also obtained by preventing formation of abrasive agglomerates and minimizing their contact with the substrate.

Creating a Community to Strengthen the Broader Impacts of Condensed Matter Physics Research

NASA Astrophysics Data System (ADS)

Adenwalla, Shireen; Bosley, Jocelyn; Voth, Gregory; Smith, Leigh

The Broader Impacts (BI) merit criteria set out by the National Science Foundation are essential for building the public support necessary for science to flourish. Condensed matter physicists (CMP) have made transformative impacts on our society, but these are often invisible to the public. Communicating the societal benefits of our research can be challenging, because CMP consists of many independent research groups for whom effective engagement in the public arena is not necessarily a forte. Other BI activities, such as engaging K-12 students and teachers to increase scientific literacy and strengthen the STEM workforce, may be very effective, but these are often isolated and short in duration. To increase the visibility of CMP and to make the implementation of BI activities more efficient, we have created a website with two sides: a public side to communicate to a broad audience exciting scientific discoveries in CMP and the technologies they enable, and a private side for condensed matter researchers to communicate with one another about effective broader impact activities. Here we discuss the content of the new website, and the best practices we have identified for communicating the excitement of CMP research to the broadest possible audience. Nsf-DMR 1550737, 1550724 and 1550681.

Spaceborne VHSIC multiprocessor system for AI applications

NASA Technical Reports Server (NTRS)

Lum, Henry, Jr.; Shrobe, Howard E.; Aspinall, John G.

1988-01-01

A multiprocessor system, under design for space-station applications, makes use of the latest generation symbolic processor and packaging technology. The result will be a compact, space-qualified system two to three orders of magnitude more powerful than present-day symbolic processing systems.

Total circulating microparticle levels are increased in patients with deep infiltrating endometriosis.

PubMed

Munrós, J; Martínez-Zamora, M A; Tàssies, D; Coloma, J L; Torrente, M A; Reverter, J C; Carmona, F; Balasch, J

2017-02-01

Are the levels of total circulating cell-derived microparticles (cMPs) and circulating tissue factor-containing microparticles (cMP-TF) increased in patients with endometriosis? The levels of total cMP, but not cMP-TF, were higher in patients with endometriosis, and these were attributed to higher levels in patients with deep infiltrating endometriosis (DIE). Previous studies have reported elevated levels of total cMP in inflammatory conditions as well as higher levels of other inflammatory biomarkers in endometriosis. Increased expression of tissue factor (a transmembrane receptor for Factor VII/VIIa) in eutopic and ectopic endometrium from patients with endometriosis has been described. There is no previous data regarding total cMP and cMP-TF levels in patients with endometriosis. A prospective case-control study including two groups of patients was carried out. The E group included 65 patients with surgically confirmed endometriosis (37 with DIE lesions) and the C group comprises 33 women without surgical findings of any form of endometriosis. Patients and controls were recruited during the same 10-month period. Controls were the next patient without endometriosis undergoing surgery, after including two patients with endometriosis. Venous blood samples for total cMP and cMP-TF determinations were obtained at the time of surgery, before anesthesia at a tertiary care center. To assess total cMP, an ELISA functional assay was used and cMP-TF activity in plasma was measured using an ELISA kit. Total cMP levels in plasma were higher in the E group compared with the C group (P < 0.0001). The subanalysis of endometriosis patients with DIE or with ovarian endometriomas without DIE showed that total cMP levels were higher in the DIE group (P = 0.001). There were no statistically significant differences in cMP-TF levels among the groups analyzed. This is a preliminary study in which the sample size was arbitrarily decided, albeit in keeping with previous studies analyzing cMP in other inflammatory diseases and other biomarkers in endometriosis. The control group included patients with other pathologies as well as healthy controls, and blood samples were taken at different phases of the cycle. Elevated total cMP levels in DIE patients may reflect an inflammatory and/or procoagulant systemic status in these patients. Further studies are warranted to confirm our findings and to assess the role of cMP levels in the pathophysiology of DIE. This study was supported in part by a grant from FIS-PI11/01560 and FIS-PI11/00977 within the 'Plan Nacional de I + D + I' and co-funded by the 'ISCIII-Subdirección General de Evaluación' and 'Fondo Europeo de Desarrollo Regional (FEDER)' and by the grant 'Premi Fi de Residència Emili Letang 2015' from the Hospital Clínic of Barcelona. The authors have no competing interests to disclose. © The Author 2016. Published by Oxford University Press on behalf of the European Society of Human Reproduction and Embryology. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Updating and improving methodology for prioritizing highway project locations on the strategic intermodal system (SIS).

DOT National Transportation Integrated Search

2016-04-01

The Florida Department of Transportation (FDOT) District One developed the Congestion Management Process : (CMP) system to prioritize low-cost, near-term highway improvements on the Strategic Intermodal System (SIS). : The existing CMP system is desi...

The way to zeros: The future of semiconductor device and chemical mechanical polishing technologies

NASA Astrophysics Data System (ADS)

Tsujimura, Manabu

2016-06-01

For the last 60 years, the development of cutting-edge semiconductor devices has strongly emphasized scaling; the effort to scale down current CMOS devices may well achieve the target of 5 nm nodes by 2020. Planarization by chemical mechanical polishing (CMP), is one technology essential for supporting scaling. This paper summarizes the history of CMP transitions in the planarization process as well as the changing degree of planarity required, and, finally, introduces innovative technologies to meet the requirements. The use of CMP was triggered by the replacement of local oxidation of silicon (LOCOS) as the element isolation technology by shallow trench isolation (STI) in the 1980s. Then, CMP’s use expanded to improving embedability of aluminum wiring, tungsten (W) contacts, Cu wiring, and, more recently, to its adoption in high-k metal gate (HKMG) and FinFET (FF) processes. Initially, the required degree of planarity was 50 nm, but now 0 nm is required. Further, zero defects on a post-CMP wafer is now the goal, and it is possible that zero psi CMP loading pressure will be required going forward. Soon, it seems, everything will have to be “zero” and perfect. Although the process is also chemical in nature, the CMP process is actually mechanical with a load added using slurry particles several tens of nm in diameter. Zero load in the loading process, zero nm planarity with no trace of processing, and zero residual foreign material, including the very slurry particles used in the process, are all required. This article will provide an overview of how to achieve these new requirements and what technologies should be employed.

Investigation of the Relationship between Anterior Knee Pain and Chondromalacia Patellae and Patellofemoral Malalignment.

PubMed

Aysin, Idil Kurut; Askin, Ayhan; Mete, Berna Dirim; Guvendi, Ece; Aysin, Murat; Kocyigit, Hikmet

2018-02-01

The study aimed to investigate whether there is any association of anterior knee pain and knee function with chondromalacia stage and patellofemoral alignment in patients with anterior knee pain for over a month and with chondromalacia patellae (CMP) detected by magnetic resonance imaging (MRI). We reviewed the medical records of 38 patients who underwent a knee MRI examination and were diagnosed with chondromalacia based on the MRI. Knee MRI images were evaluated by a radiologist for chondromalacia staging. Patients were divided into two groups as early stage (stage 1-2) and advanced stage (stage 3-4) chondromalacia. Patients' demographical data (age, sex, and occupation), clinical features, physical examination findings and patellofemoral pain severity scale, kujala patellofemoral scoring system, and functional index questionnaire scores were obtained from their medical records. Trochlear sulcus angle, sulcus depth, lateral patellofemoral angle, patellar translation, and Insall-Salvati index were measured using the MRI images. The mean patient age was higher in the advanced stage CMP group compared to the early stage CMP group (p=0.038). There was no statistically significant difference regarding other demographical data (p>0.05). MRI measurement parameters did not show difference between the groups (p>0.05). Patients in the advanced stage CMP group had higher patellofemoral pain severity score, lower kujala patellofemoral score, and lower functional index questionnaire score compared to the early stage CMP group. The differences were statistically significant (p=0.008, p=0.012, and p=0.026, respectively). As chondromalacia stage advances, the symptom severity worsens and knee functions decline; however, MRI measurements do not show difference between early and advanced stage CMP patients.

Investigation of the Relationship between Anterior Knee Pain and Chondromalacia Patellae and Patellofemoral Malalignment

PubMed Central

Aysin, Idil Kurut; Askin, Ayhan; Mete, Berna Dirim; Guvendi, Ece; Aysin, Murat; Kocyigit, Hikmet

2018-01-01

Objective: The study aimed to investigate whether there is any association of anterior knee pain and knee function with chondromalacia stage and patellofemoral alignment in patients with anterior knee pain for over a month and with chondromalacia patellae (CMP) detected by magnetic resonance imaging (MRI). Materials and Methods: We reviewed the medical records of 38 patients who underwent a knee MRI examination and were diagnosed with chondromalacia based on the MRI. Knee MRI images were evaluated by a radiologist for chondromalacia staging. Patients were divided into two groups as early stage (stage 1–2) and advanced stage (stage 3–4) chondromalacia. Patients’ demographical data (age, sex, and occupation), clinical features, physical examination findings and patellofemoral pain severity scale, kujala patellofemoral scoring system, and functional index questionnaire scores were obtained from their medical records. Trochlear sulcus angle, sulcus depth, lateral patellofemoral angle, patellar translation, and Insall–Salvati index were measured using the MRI images. Results: The mean patient age was higher in the advanced stage CMP group compared to the early stage CMP group (p=0.038). There was no statistically significant difference regarding other demographical data (p>0.05). MRI measurement parameters did not show difference between the groups (p>0.05). Patients in the advanced stage CMP group had higher patellofemoral pain severity score, lower kujala patellofemoral score, and lower functional index questionnaire score compared to the early stage CMP group. The differences were statistically significant (p=0.008, p=0.012, and p=0.026, respectively). Conclusion: As chondromalacia stage advances, the symptom severity worsens and knee functions decline; however, MRI measurements do not show difference between early and advanced stage CMP patients. PMID:29531488

Ready-to-use pre-filled syringes of atropine for anaesthesia care in French hospitals - a budget impact analysis.

PubMed

Benhamou, Dan; Piriou, Vincent; De Vaumas, Cyrille; Albaladejo, Pierre; Malinovsky, Jean-Marc; Doz, Marianne; Lafuma, Antoine; Bouaziz, Hervé

2017-04-01

Patient safety is improved by the use of labelled, ready-to-use, pre-filled syringes (PFS) when compared to conventional methods of syringe preparation (CMP) of the same product from an ampoule. However, the PFS presentation costs more than the CMP presentation. To estimate the budget impact for French hospitals of switching from atropine in ampoules to atropine PFS for anaesthesia care. A model was constructed to simulate the financial consequences of the use of atropine PFS in operating theatres, taking into account wastage and medication errors. The model tested different scenarios and a sensitivity analysis was performed. In a reference scenario, the systematic use of atropine PFS rather than atropine CMP yielded a net one-year budget saving of €5,255,304. Medication errors outweighed other cost factors relating to the use of atropine CMP (€9,425,448). Avoidance of wastage in the case of atropine CMP (prepared and unused) was a major source of savings (€1,167,323). Significant savings were made by means of other scenarios examined. The sensitivity analysis suggests that the results obtained are robust and stable for a range of parameter estimates and assumptions. The financial model was based on data obtained from the literature and expert opinions. The budget impact analysis shows that even though atropine PFS is more expensive than atropine CMP, its use would lead to significant cost savings. Savings would mainly be due to fewer medication errors and their associated consequences and the absence of wastage when atropine syringes are prepared in advance. Copyright © 2016 Société française d'anesthésie et de réanimation (Sfar). Published by Elsevier Masson SAS. All rights reserved.

Modelling parallel programs and multiprocessor architectures with AXE

NASA Technical Reports Server (NTRS)

Yan, Jerry C.; Fineman, Charles E.

1991-01-01

AXE, An Experimental Environment for Parallel Systems, was designed to model and simulate for parallel systems at the process level. It provides an integrated environment for specifying computation models, multiprocessor architectures, data collection, and performance visualization. AXE is being used at NASA-Ames for developing resource management strategies, parallel problem formulation, multiprocessor architectures, and operating system issues related to the High Performance Computing and Communications Program. AXE's simple, structured user-interface enables the user to model parallel programs and machines precisely and efficiently. Its quick turn-around time keeps the user interested and productive. AXE models multicomputers. The user may easily modify various architectural parameters including the number of sites, connection topologies, and overhead for operating system activities. Parallel computations in AXE are represented as collections of autonomous computing objects known as players. Their use and behavior is described. Performance data of the multiprocessor model can be observed on a color screen. These include CPU and message routing bottlenecks, and the dynamic status of the software.

Inhibition of DNA replication in Saccharomyces cerevisiae by araCMP.

PubMed

McIntosh, E M; Kunz, B A; Haynes, R H

1986-01-01

Cytosine arabinoside (araC), a potent inhibitor of DNA replication in mammalian cells, was found to be completely ineffective in Saccharomyces cerevisiae. The 5' monophosphate derivative, araCMP, is toxic and effectively inhibits both nuclear and mitochondrial DNA synthesis in this organism. Although wild-type strains can be inhibited by araCMP, dTMP permeable (tup-) strains were found to be much more sensitive to the analogue. In vivo labelling experiments indicate that araC enters yeast cells; however, it is extensively catabolized by deamination and breakage of the glycosidic bond. In addition, the analogue is not efficiently phosphorylated in S. cerevisiae owing to an apparent lack of deoxynucleoside kinase activity. These results provide further evidence that deoxyribonucleotides can be synthesized only through de novo pathways in this organism. Finally, araCMP was found to be recombinagenic in S. cerevisiae which suggests, together with other previous studies, that, in general, inhibition of DNA synthesis in yeast promotes mitotic recombination events.

Characterization of chemical interactions during chemical mechanical polishing (CMP) of copper

NASA Astrophysics Data System (ADS)

Lee, Seung-Mahn

2003-10-01

Chemical mechanical polishing (CMP) has received much attention as an unique technique to provide a wafer level planarization in semiconductor manufacturing. However, despite the extensive use of CMP, it still remains one of the least understood areas in semiconductor processing. The lack of the fundamental understanding is a significant barrier to further advancements in CMP technology. One critical aspect of metal CMP is the formation of a thin surface layer on the metal surface. The formation and removal of this layer controls all the aspects of the CMP process, including removal rate, surface finish, etc. In this dissertation, we focus on the characterization of the formation and removal of the thin surface layer on the copper surface. The formation dynamics was investigated using static and dynamic electrochemical techniques, including potentiodynamic scans and chronoamperometry. The results were validated using XPS measurements. The mechanical properties of the surface layer were investigated using nanoindentation measurements. The electrochemical investigation showed that the thickness of the surface layer is controlled by the chemicals such as an oxidizer (hydrogen peroxide), a corrosion inhibitor (benzotriazole), a complexing agent (citric acid), and their concentrations. The dynamic electrochemical measurements indicated that the initial layer formation kinetics is unaffected by the corrosion inhibitors. The passivation due to the corrosion inhibitor becomes important only on large time scales (>200 millisecond). The porosity and the density of the chemically modified surface layer can be affected by additives of other chemicals such as citric acid. An optimum density of the surface layer is required for high polishing rate while at the same time maintaining a high degree of surface finish. Nanoindentation measurements indicated that the mechanical properties of the surface layer are strongly dependent on the chemical additives in the slurry. The CMP removal rates were found to be in good agreement with the initial reaction kinetics as well as the mechanical properties of the chemically modified surface layer. In addition, the material removal model based on the micro- and nano-scale interactions, which were measured experimentally, has been developed.

The influence of soil organic matter chemistry and site/soil properties in predicting the decomposability of tundra soils

NASA Astrophysics Data System (ADS)

Matamala, R.; Jastrow, J. D.; Fan, Z.; Liang, C.; Calderon, F.; Michaelson, G.; Mishra, U.; Ping, C. L.

2017-12-01

With the increase in high latitude warming, there is a need to better understand the potential vulnerability of soil organic matter (SOM) stored in Arctic regions. In this study, we used mid infrared spectroscopy (MidIR) to determine the influence of soil chemistry and site properties in the short-term mineralization potential of SOM stored in tundra soils. Soils from the active and permafrost layers were collected from four tundra sites on the Coastal Plain, and Arctic Foothills of the North Slope of Alaska and were incubated for 60 days at a range of temperatures. Site and soil properties including acidic versus non-acidic tundra, lowland versus upland areas, total soil organic carbon (TOC) and total nitrogen (TN) concentrations, 60-day carbon mineralization potential (CMP), MidIR spectra and the chemical composition of the SOM stored in these soils were determined. Partial least squares (PLS) models for CMP versus MidIR spectra were produced upon splitting the dataset into site and soil properties categories. We found that SOM composition determined by MidIR spectroscopy was most effective in predicting CMP for tundra soils and it was most relevant for the active-layer mineral and upper permafrost soil horizons and/or soils with C concentrations of 10% or lower. Analysis of the factor loadings and standardized beta coefficients from the CMP PLS models indicated that spectral bands associated with clay contents, phenolic OH, aliphatic, silicates, carboxylic acids, and polysaccharides were influential for lower TOC soils, but these bands were less important for higher TOC soils. High TOC soils were influenced by a combination of other factors. Our results suggest that different factors affect the short-term CMP of SOM in tundra soils depending on the amount of TOC present. We show MidIR as a powerful tool for quickly and reasonably estimating the short-term CMP of tundra soils. Widespread application of MidIR measurements to already collected and archived tundra region soils could provide a quick and reliable assessment of the CMP of these soils, reduce the need for incubation studies, and contribute to upscaling and model benchmarking of SOM mineralization of tundra soils.

Multipurpose silicon photonics signal processor core.

PubMed

Pérez, Daniel; Gasulla, Ivana; Crudgington, Lee; Thomson, David J; Khokhar, Ali Z; Li, Ke; Cao, Wei; Mashanovich, Goran Z; Capmany, José

2017-09-21

Integrated photonics changes the scaling laws of information and communication systems offering architectural choices that combine photonics with electronics to optimize performance, power, footprint, and cost. Application-specific photonic integrated circuits, where particular circuits/chips are designed to optimally perform particular functionalities, require a considerable number of design and fabrication iterations leading to long development times. A different approach inspired by electronic Field Programmable Gate Arrays is the programmable photonic processor, where a common hardware implemented by a two-dimensional photonic waveguide mesh realizes different functionalities through programming. Here, we report the demonstration of such reconfigurable waveguide mesh in silicon. We demonstrate over 20 different functionalities with a simple seven hexagonal cell structure, which can be applied to different fields including communications, chemical and biomedical sensing, signal processing, multiprocessor networks, and quantum information systems. Our work is an important step toward this paradigm.Integrated optical circuits today are typically designed for a few special functionalities and require complex design and development procedures. Here, the authors demonstrate a reconfigurable but simple silicon waveguide mesh with different functionalities.

The Unification of Space Qualified Integrated Circuits by Example of International Space Project GAMMA-400

NASA Astrophysics Data System (ADS)

Bobkov, S. G.; Serdin, O. V.; Arkhangelskiy, A. I.; Arkhangelskaja, I. V.; Suchkov, S. I.; Topchiev, N. P.

The problem of electronic component unification at the different levels (circuits, interfaces, hardware and software) used in space industry is considered. The task of computer systems for space purposes developing is discussed by example of scientific data acquisition system for space project GAMMA-400. The basic characteristics of high reliable and fault tolerant chips developed by SRISA RAS for space applicable computational systems are given. To reduce power consumption and enhance data reliability, embedded system interconnect made hierarchical: upper level is Serial RapidIO 1x or 4x with rate transfer 1.25 Gbaud; next level - SpaceWire with rate transfer up to 400 Mbaud and lower level - MIL-STD-1553B and RS232/RS485. The Ethernet 10/100 is technology interface and provided connection with the previously released modules too. Systems interconnection allows creating different redundancy systems. Designers can develop heterogeneous systems that employ the peer-to-peer networking performance of Serial RapidIO using multiprocessor clusters interconnected by SpaceWire.

A general model for memory interference in a multiprocessor system with memory hierarchy

NASA Technical Reports Server (NTRS)

Taha, Badie A.; Standley, Hilda M.

1989-01-01

The problem of memory interference in a multiprocessor system with a hierarchy of shared buses and memories is addressed. The behavior of the processors is represented by a sequence of memory requests with each followed by a determined amount of processing time. A statistical queuing network model for determining the extent of memory interference in multiprocessor systems with clusters of memory hierarchies is presented. The performance of the system is measured by the expected number of busy memory clusters. The results of the analytic model are compared with simulation results, and the correlation between them is found to be very high.

Experimental evaluation of multiprocessor cache-based error recovery

NASA Technical Reports Server (NTRS)

Janssens, Bob; Fuchs, W. K.

1991-01-01

Several variations of cache-based checkpointing for rollback error recovery in shared-memory multiprocessors have been recently developed. By modifying the cache replacement policy, these techniques use the inherent redundancy in the memory hierarchy to periodically checkpoint the computation state. Three schemes, different in the manner in which they avoid rollback propagation, are evaluated. By simulation with address traces from parallel applications running on an Encore Multimax shared-memory multiprocessor, the performance effect of integrating the recovery schemes in the cache coherence protocol are evaluated. The results indicate that the cache-based schemes can provide checkpointing capability with low performance overhead but uncontrollable high variability in the checkpoint interval.

Connected Mathematics Project (CMP). What Works Clearinghouse Intervention Report

ERIC Educational Resources Information Center

What Works Clearinghouse, 2010

2010-01-01

The "Connected Mathematics Project" ("CMP") is a mathematics curriculum designed for students in grades 6-8. Each grade level of the curriculum is a full-year program and covers numbers, algebra, geometry/measurement, probability, and statistics. The curriculum uses an investigative approach, and students utilize interactive…

Deoxycytidine and Deoxythymidine Treatment for Thymidine Kinase 2 Deficiency.

PubMed

Lopez-Gomez, Carlos; Levy, Rebecca J; Sanchez-Quintero, Maria J; Juanola-Falgarona, Martí; Barca, Emanuele; Garcia-Diaz, Beatriz; Tadesse, Saba; Garone, Caterina; Hirano, Michio

2017-05-01

Thymidine kinase 2 (TK2), a critical enzyme in the mitochondrial pyrimidine salvage pathway, is essential for mitochondrial DNA (mtDNA) maintenance. Mutations in the nuclear gene, TK2, cause TK2 deficiency, which manifests predominantly in children as myopathy with mtDNA depletion. Molecular bypass therapy with the TK2 products, deoxycytidine monophosphate (dCMP) and deoxythymidine monophosphate (dTMP), prolongs the life span of Tk2-deficient (Tk2 -/- ) mice by 2- to 3-fold. Because we observed rapid catabolism of the deoxynucleoside monophosphates to deoxythymidine (dT) and deoxycytidine (dC), we hypothesized that: (1) deoxynucleosides might be the major active agents and (2) inhibition of deoxycytidine deamination might enhance dTMP+dCMP therapy. To test these hypotheses, we assessed two therapies in Tk2 -/- mice: (1) dT+dC and (2) coadministration of the deaminase inhibitor, tetrahydrouridine (THU), with dTMP+dCMP. We observed that dC+dT delayed disease onset, prolonged life span of Tk2-deficient mice and restored mtDNA copy number as well as respiratory chain enzyme activities and levels. In contrast, dCMP+dTMP+THU therapy decreased life span of Tk2 -/- animals compared to dCMP+dTMP. Our studies demonstrate that deoxynucleoside substrate enhancement is a novel therapy, which may ameliorate TK2 deficiency in patients. Ann Neurol 2017;81:641-652. © 2017 American Neurological Association.

Increased circulating cell-derived microparticle count is associated with recurrent implantation failure after IVF and embryo transfer.

PubMed

Martínez-Zamora, M Angeles; Tàssies, Dolors; Reverter, Juan Carlos; Creus, Montserrat; Casals, Gemma; Cívico, Salvadora; Carmona, Francisco; Balasch, Juan

2016-08-01

Cell-derived microparticles (cMPs) are small membrane vesicles that are released from many different cell types in response to cellular activation or apoptosis. Elevated cMP counts have been found in almost all thrombotic diseases and pregnancy wastage, such as recurrent spontaneous abortion and in a number of conditions associated with inflammation, cellular activation and angiogenesis. cMP count was investigated in patients experiencing unexplained recurrent implantation failure (RIF). The study group was composed of 30 women diagnosed with RIF (RIF group). The first control group (IVF group) (n = 30) comprised patients undergoing a first successful IVF cycle. The second control group (FER group) included 30 healthy women who had at least one child born at term and no history of infertility or obstetric complications. cMP count was significantly higher in the RIF group compared with the IVF and FER groups (P < 0.05 and P < 0.01, respectively) (RIF group: 15.8 ± 6.2 nM phosphatidylserine equivalent [PS eq]; IVF group: 10.9 ± 5.3 nM PS eq; FER group: 9.6 ± 4.0 nM PS eq). No statistical difference was found in cMP count between the IVF and FER groups. Increased cMP count is, therefore, associated with RIF after IVF and embryo transfer. Copyright © 2016. Published by Elsevier Ltd.

Polymorphous Computing Architectures

DTIC Science & Technology

2007-12-12

provide a multiprocessor implementation. In this work, we introduce the Atomos transactional programming language, which is the first to include...implicit transactions, strong atomicity, and a scalable multiprocessor implementation [47]. Atomos is derived from Java, but replaces its synchronization...and conditional waiting constructs with transactional alternatives. The Atomos conditional waiting proposal is tailored to allow efficient

Validity of Self-Reported Concentration and Memory Problems: Relationship with Neuropsychological Assessment and Depression

EPA Science Inventory

Background: This study investigated the validity of self-reported concentration and memory problems (CMP) in residents environmentally exposed to manganese (Mn). Method: Self-report of CMP from a health questionnaire (HQ) and the Symptoms Checklist-90-Revised (SCL-90-R) was com...

Interim Action Proposed Plan for the Chemicals, Metals, and Pesticides (CMP) Pits Operable Unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley, J.

2002-06-18

The purpose of this Interim Action Proposed Plan (IAPP) is to describe the preferred interim remedial action for addressing the Chemicals, Metals, and Pesticides (CMP) Pits Operable Unit and to provide an opportunity for public input into the remedial action selection process.

Incorporating Nondrug Social & Recreational Activities in Outpatient Chemical Dependency Treatment

ERIC Educational Resources Information Center

Siporin, Sheldon; Baron, Lisa

2012-01-01

"Contingency Management programs (CMP) and non-drug social and recreational activities (NDSRA) are interventions premised on behavior theory that rely on external sources of reinforcement alternative to drug-based forms to decrease drug use. CMP usually employs vouchers as reinforcement for negative toxicologies. Despite research support, CMP…

42 CFR 417.594 - Computation of adjusted community rate (ACR).

Code of Federal Regulations, 2012 CFR

2012-10-01

... HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM (CONTINUED) HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE... or CMP develops an aggregate premium for all its enrollees and weights the aggregate by the size of... groups are defined as employee groups or other bodies of subscribers that enroll in the HMO or CMP...

42 CFR 417.594 - Computation of adjusted community rate (ACR).

Code of Federal Regulations, 2014 CFR

2014-10-01

... HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM (CONTINUED) HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE... or CMP develops an aggregate premium for all its enrollees and weights the aggregate by the size of... groups are defined as employee groups or other bodies of subscribers that enroll in the HMO or CMP...

42 CFR 417.594 - Computation of adjusted community rate (ACR).

Code of Federal Regulations, 2013 CFR

2013-10-01

... HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM (CONTINUED) HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE... or CMP develops an aggregate premium for all its enrollees and weights the aggregate by the size of... groups are defined as employee groups or other bodies of subscribers that enroll in the HMO or CMP...

42 CFR 417.424 - Denial of enrollment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the criteria of § 417.422 if acceptance would— (1) Cause the number of enrollees who are Medicare or... become substantially nonrepresentative of the general population in the HMO's or CMP's geographic area... the enrollment of the HMO or CMP substantially nonrepresentative of the general population in the HMO...

42 CFR 417.424 - Denial of enrollment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the criteria of § 417.422 if acceptance would— (1) Cause the number of enrollees who are Medicare or... become substantially nonrepresentative of the general population in the HMO's or CMP's geographic area... the enrollment of the HMO or CMP substantially nonrepresentative of the general population in the HMO...

42 CFR 417.424 - Denial of enrollment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the criteria of § 417.422 if acceptance would— (1) Cause the number of enrollees who are Medicare or... become substantially nonrepresentative of the general population in the HMO's or CMP's geographic area... the enrollment of the HMO or CMP substantially nonrepresentative of the general population in the HMO...

42 CFR 417.458 - Recoupment of uncollected deductible and coinsurance amounts.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM HEALTH MAINTENANCE ORGANIZATIONS... Medicare Contract § 417.458 Recoupment of uncollected deductible and coinsurance amounts. An HMO or CMP... previous contract period except in the following circumstances: (a) The HMO or CMP failed to collect the...

42 CFR 417.422 - Eligibility to enroll in an HMO or CMP.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SERVICES (CONTINUED) MEDICARE PROGRAM HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE MEDICAL PLANS, AND HEALTH CARE PREPAYMENT PLANS Enrollment, Entitlement, and Disenrollment under Medicare Contract § 417.422... entered into a contract under subpart L of this part; (d) During an enrollment period of the HMO or CMP...

Connected Mathematics Project (CMP). What Works Clearinghouse Intervention Report. Updated

ERIC Educational Resources Information Center

What Works Clearinghouse, 2017

2017-01-01

"Connected Mathematics Project" (CMP) is a math curriculum for students in grades 6-8. It uses interactive problems and everyday situations to explore mathematical ideas, with a goal of fostering a problem-centered, inquiry-based learning environment. At each grade level, the curriculum covers numbers, algebra, geometry/measurement,…

48 CFR 732.406-74 - Revocation of the LOC.

Code of Federal Regulations, 2011 CFR

2011-10-01

....406-74 Section 732.406-74 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT GENERAL CONTRACTING REQUIREMENTS CONTRACT FINANCING Advance Payments 732.406-74 Revocation of the LOC. If during the term of the contract FM/CMP believes that the LOC should be revoked, FM/CMP may, after...

48 CFR 732.406-74 - Revocation of the LOC.

Code of Federal Regulations, 2010 CFR

2010-10-01

....406-74 Section 732.406-74 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT GENERAL CONTRACTING REQUIREMENTS CONTRACT FINANCING Advance Payments 732.406-74 Revocation of the LOC. If during the term of the contract FM/CMP believes that the LOC should be revoked, FM/CMP may, after...

42 CFR 417.576 - Final settlement.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the HMO's or CMP's submission and CMS's review of an independently certified cost report and... that begin on or after January 1, 1996, the costs of hospital and SNF services paid by Medicare's intermediaries under the option provided by § 417.532(d). (ii) The HMO's or CMP's methods of apportioning cost...

42 CFR 417.576 - Final settlement.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the HMO's or CMP's submission and CMS's review of an independently certified cost report and... that begin on or after January 1, 1996, the costs of hospital and SNF services paid by Medicare's intermediaries under the option provided by § 417.532(d). (ii) The HMO's or CMP's methods of apportioning cost...

Surface topography analysis and performance on post-CMP images (Conference Presentation)

NASA Astrophysics Data System (ADS)

Lee, Jusang; Bello, Abner F.; Kakita, Shinichiro; Pieniazek, Nicholas; Johnson, Timothy A.

2017-03-01

Surface topography on post-CMP processing can be measured with white light interference microscopy to determine the planarity. Results are used to avoid under or over polishing and to decrease dishing. The numerical output of the surface topography is the RMS (root-mean-square) of the height. Beyond RMS, the topography image is visually examined and not further quantified. Subjective comparisons of the height maps are used to determine optimum CMP process conditions. While visual comparison of height maps can determine excursions, it's only through manual inspection of the images. In this work we describe methods of quantifying post-CMP surface topography characteristics that are used in other technical fields such as geography and facial-recognition. The topography image is divided into small surface patches of 7x7 pixels. Each surface patch is fitted to an analytic surface equation, in this case a third order polynomial, from which the gradient, directional derivatives, and other characteristics are calculated. Based on the characteristics, the surface patch is labeled as peak, ridge, flat, saddle, ravine, pit or hillside. The number of each label and thus the associated histogram is then used as a quantified characteristic of the surface topography, and could be used as a parameter for SPC (statistical process control) charting. In addition, the gradient for each surface patch is calculated, so the average, maximum, and other characteristics of the gradient distribution can be used for SPC. Repeatability measurements indicate high confidence where individual labels can be lower than 2% relative standard deviation. When the histogram is considered, an associated chi-squared value can be defined from which to compare other measurements. The chi-squared value of the histogram is a very sensitive and quantifiable parameter to determine the within wafer and wafer-to-wafer topography non-uniformity. As for the gradient histogram distribution, the chi-squared could again be calculated and used as yet another quantifiable parameter for SPC. In this work we measured the post Cu CMP of a die designed for 14nm technology. A region of interest (ROI) known to be indicative of the CMP processing is chosen for the topography analysis. The ROI, of size 1800 x 2500 pixels where each pixel represents 2um, was repeatably measured. We show the sensitivity based on measurements and the comparison between center and edge die measurements. The topography measurements and surface patch analysis were applied to hundreds of images representing the periodic process qualification runs required to control and verify CMP performance and tool matching. The analysis is shown to be sensitive to process conditions that vary in polishing time, type of slurry, CMP tool manufacturer, and CMP pad lifetime. Keywords: Keywords: CMP, Topography, Image Processing, Metrology, Interference microscopy, surface processing [1] De Lega, Xavier Colonna, and Peter De Groot. "Optical topography measurement of patterned wafers." Characterization and Metrology for ULSI Technology 2005 788 (2005): 432-436. [2] de Groot, Peter. "Coherence scanning interferometry." Optical Measurement of Surface Topography. Springer Berlin Heidelberg, 2011. 187-208. [3] Watson, Layne T., Thomas J. Laffey, and Robert M. Haralick. "Topographic classification of digital image intensity surfaces using generalized splines and the discrete cosine transformation." Computer Vision, Graphics, and Image Processing 29.2 (1985): 143-167. [4] Wang, Jun, et al. "3D facial expression recognition based on primitive surface feature distribution." Computer Vision and Pattern Recognition, 2006 IEEE Computer Society Conference on. Vol. 2. IEEE, 2006.

C-MOS array design techniques: SUMC multiprocessor system study

NASA Technical Reports Server (NTRS)

Clapp, W. A.; Helbig, W. A.; Merriam, A. S.

1972-01-01

The current capabilities of LSI techniques for speed and reliability, plus the possibilities of assembling large configurations of LSI logic and storage elements, have demanded the study of multiprocessors and multiprocessing techniques, problems, and potentialities. Evaluated are three previous systems studies for a space ultrareliable modular computer multiprocessing system, and a new multiprocessing system is proposed that is flexibly configured with up to four central processors, four 1/0 processors, and 16 main memory units, plus auxiliary memory and peripheral devices. This multiprocessor system features a multilevel interrupt, qualified S/360 compatibility for ground-based generation of programs, virtual memory management of a storage hierarchy through 1/0 processors, and multiport access to multiple and shared memory units.

Identification of cytidine 2',3'-cyclic monophosphate and uridine 2',3'-cyclic monophosphate in Pseudomonas fluorescens pfo-1 culture.

PubMed

Bordeleau, Emily; Oberc, Christopher; Ameen, Eve; da Silva, Amanda Mendes; Yan, Hongbin

2014-09-15

Cytidine 2',3'-cyclic monophosphate (2',3'-cCMP) and uridine 2',3'-cyclic monophosphate (2',3'-cUMP) were isolated from Pseudomonas fluorescens pfo-1 cell extracts by semi-preparative reverse phase HPLC. The structures of the two compounds were confirmed by NMR and mass spectroscopy against commercially available authentic samples. Concentrations of both intracellular and extracellular 2',3'-cCMP and 2',3'-cUMP were determined. Addition of 2',3'-cCMP and 2',3'-cUMP to P. fluorescens pfo-1 culture did not significantly affect the level of biofilm formation in static liquid cultures. Copyright © 2014 Elsevier Ltd. All rights reserved.

Silicon photonics for high-performance interconnection networks

NASA Astrophysics Data System (ADS)

Biberman, Aleksandr

2011-12-01

We assert in the course of this work that silicon photonics has the potential to be a key disruptive technology in computing and communication industries. The enduring pursuit of performance gains in computing, combined with stringent power constraints, has fostered the ever-growing computational parallelism associated with chip multiprocessors, memory systems, high-performance computing systems, and data centers. Sustaining these parallelism growths introduces unique challenges for on- and off-chip communications, shifting the focus toward novel and fundamentally different communication approaches. This work showcases that chip-scale photonic interconnection networks, enabled by high-performance silicon photonic devices, enable unprecedented bandwidth scalability with reduced power consumption. We demonstrate that the silicon photonic platforms have already produced all the high-performance photonic devices required to realize these types of networks. Through extensive empirical characterization in much of this work, we demonstrate such feasibility of waveguides, modulators, switches, and photodetectors. We also demonstrate systems that simultaneously combine many functionalities to achieve more complex building blocks. Furthermore, we leverage the unique properties of available silicon photonic materials to create novel silicon photonic devices, subsystems, network topologies, and architectures to enable unprecedented performance of these photonic interconnection networks and computing systems. We show that the advantages of photonic interconnection networks extend far beyond the chip, offering advanced communication environments for memory systems, high-performance computing systems, and data centers. Furthermore, we explore the immense potential of all-optical functionalities implemented using parametric processing in the silicon platform, demonstrating unique methods that have the ability to revolutionize computation and communication. Silicon photonics enables new sets of opportunities that we can leverage for performance gains, as well as new sets of challenges that we must solve. Leveraging its inherent compatibility with standard fabrication techniques of the semiconductor industry, combined with its capability of dense integration with advanced microelectronics, silicon photonics also offers a clear path toward commercialization through low-cost mass-volume production. Combining empirical validations of feasibility, demonstrations of massive performance gains in large-scale systems, and the potential for commercial penetration of silicon photonics, the impact of this work will become evident in the many decades that follow.

Static Scheduler for Hard Real-Time Tasks on Multiprocessor Systems

DTIC Science & Technology

1992-09-01

Foundation of Computer Science, 1980 . [SIM83] Simons, B., "Multiprocessor Scheduling of Unit-Time Jobs with Arbitrary Release Times and Deadlines", SIAM...Research Office Attn: Dr. David Hislop P. O. Box 12211 Research Triangle Park, NC 27709-2211 31. Persistent Data Systems 75 W. Chapel Ridge Road Attn: Dr

Fault tree models for fault tolerant hypercube multiprocessors

NASA Technical Reports Server (NTRS)

Boyd, Mark A.; Tuazon, Jezus O.

1991-01-01

Three candidate fault tolerant hypercube architectures are modeled, their reliability analyses are compared, and the resulting implications of these methods of incorporating fault tolerance into hypercube multiprocessors are discussed. In the course of performing the reliability analyses, the use of HARP and fault trees in modeling sequence dependent system behaviors is demonstrated.

Modeling and measurement of fault-tolerant multiprocessors

NASA Technical Reports Server (NTRS)

Shin, K. G.; Woodbury, M. H.; Lee, Y. H.

1985-01-01

The workload effects on computer performance are addressed first for a highly reliable unibus multiprocessor used in real-time control. As an approach to studing these effects, a modified Stochastic Petri Net (SPN) is used to describe the synchronous operation of the multiprocessor system. From this model the vital components affecting performance can be determined. However, because of the complexity in solving the modified SPN, a simpler model, i.e., a closed priority queuing network, is constructed that represents the same critical aspects. The use of this model for a specific application requires the partitioning of the workload into job classes. It is shown that the steady state solution of the queuing model directly produces useful results. The use of this model in evaluating an existing system, the Fault Tolerant Multiprocessor (FTMP) at the NASA AIRLAB, is outlined with some experimental results. Also addressed is the technique of measuring fault latency, an important microscopic system parameter. Most related works have assumed no or a negligible fault latency and then performed approximate analyses. To eliminate this deficiency, a new methodology for indirectly measuring fault latency is presented.

42 CFR 417.544 - Physicians' services furnished directly by the HMO or CMP.

Code of Federal Regulations, 2010 CFR

2010-10-01

... attributable to salaries, wages, incentive payments, fringe benefits) must be distinguished from the cost of... 42 Public Health 3 2010-10-01 2010-10-01 false Physicians' services furnished directly by the HMO or CMP. 417.544 Section 417.544 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF...

75 FR 9864 - Fisheries of the Caribbean, Gulf of Mexico and South Atlantic; Comprehensive Ecosystem-Based...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-04

... Coastal Migratory Pelagic (CMP) Resources (CMP FMP); and the FMP for the Spiny Lobster Fishery of the Gulf... golden crab and deepwater shrimp fisheries while extending protection for deepwater coral ecosystems. CE-BA 1 would also amend the Coral, Shrimp, Coastal Migratory Pelagics, Golden Crab, Spiny Lobster...

Clinicians' and Patients' Assessment of Activity Overuse and Underuse and Its Relation to Physical Capacity

ERIC Educational Resources Information Center

de Jong, Annemieke Bonny; Preuper, Henrica R. Schiphorst; Reneman, Michiel F.

2012-01-01

To explore clinicians' and patients' (self)-assessment of activity overuse and underuse, and its relationship with physical capacity in patients with chronic musculoskeletal pain (CMP). Study design was cross-sectional. Participants included patients with CMP, admitted to a multidisciplinary outpatient pain rehabilitation program. The main…

42 CFR 417.440 - Entitlement to health care services from an HMO or CMP.

Code of Federal Regulations, 2010 CFR

2010-10-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE... Contract § 417.440 Entitlement to health care services from an HMO or CMP. (a) Basic rules. (1) Subject to... not converted to the risk portion of the contract, may enroll in a special supplemental plan, if...

Medicare and State Health Care Programs: Fraud and Abuse; Revisions to the Office of Inspector General's Civil Monetary Penalty Rules. Final rule.

PubMed

2016-12-07

This final rule amends the civil monetary penalty (CMP or penalty) rules of the Office of Inspector General to incorporate new CMP authorities, clarify existing authorities, and reorganize regulations on civil money penalties, assessments, and exclusions to improve readability and clarity.

42 CFR 417.558 - Emergency, urgently needed, and out-of-area services for which the HMO or CMP accepts...

Code of Federal Regulations, 2010 CFR

2010-10-01

... services for which the HMO or CMP accepts responsibility. 417.558 Section 417.558 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE MEDICAL PLANS, AND HEALTH CARE PREPAYMENT PLANS Medicare Payment: Cost...

Study on effect of the surface variation of colloidal silica abrasive during chemical mechanical polishing of sapphire

NASA Astrophysics Data System (ADS)

Bun-Athuek, Natthaphon; Yoshimoto, Yutaka; Sakai, Koya; Khajornrungruang, Panart; Suzuki, Keisuke

2017-07-01

The surface and diameter size variations of colloidal silica particles during the chemical mechanical polishing (CMP) of sapphire substrates were investigated using different particle diameters of 20 and 55 nm. Dynamic light scattering (DLS) results show that the silica particles became larger after CMP under both conditions. The increase in particle size in the slurry was proportional to the material removal amount (MRA) as a function of the removed volume of sapphire substrates by CMP and affected the material removal rate (MRR). Transmission electron microscopy (TEM) images revealed an increase in the size of the fine particles and a change in their surface shape in the slurry. The colloidal silica was coated with the material removed from the substrate during CMP. In this case, the increase in the size of 55 nm diameter particles is larger than that of 20 nm diameter particles. X-ray fluorescence spectrometry (XRF) results indicate that the aluminum element from polished sapphire substrates adhered to the surfaces of silica particles. Therefore, MRR decreases with increasing of polishing time owing to the degradation of particles in the slurry.

Chitin nanofibrils for rapid and efficient removal of metal ions from water system.

PubMed

Liu, Dagang; Zhu, Yi; Li, Zehui; Tian, Donglin; Chen, Lei; Chen, Peng

2013-10-15

Joint mechanical defibrillation was successfully used to downsize chitin micro-particles (CMP) into nanofibrils without changing its chemical or crystalline structure. The fine chitin nanofibrils (CNF) bearing width of about 50 nm and length of more than 1 μm were then developed as heavy metal ion sorbents. The uptake performance of CNF dependent on pH, ionic concentration, time, and temperature was investigated. Results show that fixation amount of Cd(II), Ni(II), Cu(II), Zn(II), Pb(II), Cr(III) on CNF was up to 2.94, 2.30, 2.22, 2.06, 1.46, and 0.31 mmol/g, respectively, much higher than CMP due to high specific surface area and widely distributed pores of CNF. Adsorption kinetics of CMP and CNF followed pseudo-second-order model and Freundlich isotherm although CNF exhibited higher rate constant and sorption capacity than that of CMP. The defibrillated CNF is renewable, feasible, easily recyclable, and is thought as good candidate for heavy metal ion treatment due to their low sorption energy, rapid and efficient uptake capacity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Ribonucleotide incorporation by human DNA polymerase η impacts translesion synthesis and RNase H2 activity

PubMed Central

Mentegari, Elisa; Crespan, Emmanuele; Bavagnoli, Laura; Kissova, Miroslava; Bertoletti, Federica; Sabbioneda, Simone; Imhof, Ralph; Sturla, Shana J.; Nilforoushan, Arman; Hübscher, Ulrich; van Loon, Barbara

2017-01-01

Abstract Ribonucleotides (rNs) incorporated in the genome by DNA polymerases (Pols) are removed by RNase H2. Cytidine and guanosine preferentially accumulate over the other rNs. Here we show that human Pol η can incorporate cytidine monophosphate (rCMP) opposite guanine, 8-oxo-7,8-dihydroguanine, 8-methyl-2΄-deoxyguanosine and a cisplatin intrastrand guanine crosslink (cis-PtGG), while it cannot bypass a 3-methylcytidine or an abasic site with rNs as substrates. Pol η is also capable of synthesizing polyribonucleotide chains, and its activity is enhanced by its auxiliary factor DNA Pol δ interacting protein 2 (PolDIP2). Human RNase H2 removes cytidine and guanosine less efficiently than the other rNs and incorporation of rCMP opposite DNA lesions further reduces the efficiency of RNase H2. Experiments with XP-V cell extracts indicate Pol η as the major basis of rCMP incorporation opposite cis-PtGG. These results suggest that translesion synthesis by Pol η can contribute to the accumulation of rCMP in the genome, particularly opposite modified guanines. PMID:27994034

Two-dimensional cross correlation analysis of protein unfolding: Portrayal of the thermal denaturation of CMP kinases in the absence and presence of substrates

NASA Astrophysics Data System (ADS)

Schultz, Christian P.; Bârzu, Octavian; Mantsch, Henry H.

2000-03-01

The functional role of CMP kinases is to regenerate mono-phosphate nucleotides in cells by transferring phosphate residues from tri-phosphorylated nucleotides to monophosphorylated nucleotides. These enzymes possess two binding sites and maintain a highly conserved secondary structure. They are essential for cell survival. Herein we compare the infrared spectra of two similar, but not identical enzymes, the CMP kinases from Escherichia coli and Bacillus subtilis. A two-dimensional cross correlation analysis of the infrared spectra reveals differences in the denaturation behavior of the two proteins. Different secondary structure elements show different time-delayed or advanced unfolding events in the two enzymes. When bound to the active sites, the two nucleotide-substrates CMP and ATP exert a stabilizing effect on the structure of both proteins. The changes observed upon thermal denaturation are different for the two enzymes. Model 2D correlations are used to simulate the different denaturation of the two enzymes. Thermal denaturation and aggregation can be distinguished as two processes separated in time.

Primary care physicians, acupuncture and chiropractic clinicians, and chronic pain patients: a qualitative analysis of communication and care coordination patterns.

PubMed

Penney, Lauren S; Ritenbaugh, Cheryl; Elder, Charles; Schneider, Jennifer; Deyo, Richard A; DeBar, Lynn L

2016-01-25

A variety of people, with multiple perspectives, make up the system comprising chronic musculoskeletal pain (CMP) treatment. While there are frequently problems in communication and coordination of care within conventional health systems, more opportunities for communicative disruptions seem possible when providers use different explanatory models and are not within the same health management system. We sought to describe the communication system surrounding the management of chronic pain from the perspectives of allopathic providers, acupuncture and chiropractor (A/C) providers, and CMP patients. We collected qualitative data from CMP patients (n = 90) and primary care physicians (PCPs) (n = 25) in a managed care system, and community acupuncture and chiropractic care providers (n = 14) who received high levels of referrals from the system, in the context of a longitudinal study of CMP patients' experience. Multiple points of divergence and communicative barriers were identified among the main stakeholders in the system. Those that were most frequently mentioned included issues surrounding the referral process (requesting, approving) and lack of consistent information flow back to providers that impairs overall management of patient care. We found that because of these problems, CMP patients were frequently tasked and sometimes overwhelmed with integrating and coordinating their own care, with little help from the system. Patients, PCPs, and A/C providers desire more communication; thus systems need to be created to facilitate more open communication which could positively benefit patient outcomes.

Antibody-independent identification of bovine milk-derived peptides in breast-milk.

PubMed

Picariello, Gianluca; Addeo, Francesco; Ferranti, Pasquale; Nocerino, Rita; Paparo, Lorella; Passariello, Annalisa; Dallas, David C; Robinson, Randall C; Barile, Daniela; Canani, Roberto Berni

2016-08-10

Exclusively breast-fed infants can exhibit clear signs of IgE or non IgE-mediated cow's milk allergy. However, the definite characterization of dietary cow's milk proteins (CMP) that survive the maternal digestive tract to be absorbed into the bloodstream and secreted into breast milk remains missing. Herein, we aimed at assessing possible CMP-derived peptides in breast milk. Using high performance liquid chromatography (HPLC)-high resolution mass spectrometry (MS), we compared the peptide fraction of breast milk from 12 donors, among which 6 drank a cup of milk daily and 6 were on a strict dairy-free diet. We identified two bovine β-lactoglobulin (β-Lg, 2 out 6 samples) and one αs1-casein (1 out 6 samples) fragments in breast milk from mothers receiving a cup of bovine milk daily. These CMP-derived fragments, namely β-Lg (f42-54), (f42-57) and αs1-casein (f180-197), were absent in milk from mothers on dairy-free diet. In contrast, neither intact nor hydrolyzed β-Lg was detected by western blot and competitive ELISA in any breast milk sample. Eight additional bovine milk-derived peptides identified by software-assisted MS were most likely false positive. The results of this study demonstrate that CMP-derived peptides rather than intact CMP may sensitize or elicit allergic responses in the neonate through mother's milk. Immunologically active peptides from the maternal diet could be involved in priming the newborn's immune system, driving a tolerogenic response.

Case mix, outcome and length of stay for admissions to adult, general critical care units in England, Wales and Northern Ireland: the Intensive Care National Audit & Research Centre Case Mix Programme Database

PubMed Central

2005-01-01

Introduction The present paper describes the methods of data collection and validation employed in the Intensive Care National Audit & Research Centre Case Mix Programme (CMP), a national comparative audit of outcome for adult, critical care admissions. The paper also describes the case mix, outcome and activity of the admissions in the Case Mix Programme Database (CMPD). Methods The CMP collects data on consecutive admissions to adult, general critical care units in England, Wales and Northern Ireland. Explicit steps are taken to ensure the accuracy of the data, including use of a dataset specification, of initial and refresher training courses, and of local and central validation of submitted data for incomplete, illogical and inconsistent values. Criteria for evaluating clinical databases developed by the Directory of Clinical Databases were applied to the CMPD. The case mix, outcome and activity for all admissions were briefly summarised. Results The mean quality level achieved by the CMPD for the 10 Directory of Clinical Databases criteria was 3.4 (on a scale of 1 = worst to 4 = best). The CMPD contained validated data on 129,647 admissions to 128 units. The median age was 63 years, and 59% were male. The mean Acute Physiology and Chronic Health Evaluation II score was 16.5. Mortality was 20.3% in the CMP unit and was 30.8% at ultimate discharge from hospital. Nonsurvivors stayed longer in intensive care than did survivors (median 2.0 days versus 1.7 days in the CMP unit) but had a shorter total hospital length of stay (9 days versus 16 days). Results for the CMPD were comparable with results from other published reports of UK critical care admissions. Conclusions The CMP uses rigorous methods to ensure data are complete, valid and reliable. The CMP scores well against published criteria for high-quality clinical databases.

Case mix, outcome and length of stay for admissions to adult, general critical care units in England, Wales and Northern Ireland: the Intensive Care National Audit & Research Centre Case Mix Programme Database

PubMed Central

Harrison, David A; Brady, Anthony R; Rowan, Kathy

2004-01-01

Introduction The present paper describes the methods of data collection and validation employed in the Intensive Care National Audit & Research Centre Case Mix Programme (CMP), a national comparative audit of outcome for adult, critical care admissions. The paper also describes the case mix, outcome and activity of the admissions in the Case Mix Programme Database (CMPD). Methods The CMP collects data on consecutive admissions to adult, general critical care units in England, Wales and Northern Ireland. Explicit steps are taken to ensure the accuracy of the data, including use of a dataset specification, of initial and refresher training courses, and of local and central validation of submitted data for incomplete, illogical and inconsistent values. Criteria for evaluating clinical databases developed by the Directory of Clinical Databases were applied to the CMPD. The case mix, outcome and activity for all admissions were briefly summarised. Results The mean quality level achieved by the CMPD for the 10 Directory of Clinical Databases criteria was 3.4 (on a scale of 1 = worst to 4 = best). The CMPD contained validated data on 129,647 admissions to 128 units. The median age was 63 years, and 59% were male. The mean Acute Physiology and Chronic Health Evaluation II score was 16.5. Mortality was 20.3% in the CMP unit and was 30.8% at ultimate discharge from hospital. Nonsurvivors stayed longer in intensive care than did survivors (median 2.0 days versus 1.7 days in the CMP unit) but had a shorter total hospital length of stay (9 days versus 16 days). Results for the CMPD were comparable with results from other published reports of UK critical care admissions. Conclusions The CMP uses rigorous methods to ensure data are complete, valid and reliable. The CMP scores well against published criteria for high-quality clinical databases. PMID:15025784

Immunochemical characterization of Glycine max L. Merr. var Raiden, as a possible hypoallergenic substitute for cow's milk-allergic patients.

PubMed

Curciarello, R; Lareu, J F; Fossati, C A; Docena, G H; Petruccelli, S

2008-09-01

Cows' milk allergy (CMA) is the most common cause of food allergy in infancy. The only proven treatment is the complete elimination of cows' milk proteins (CMPs) from the diet by means of hypoallergenic formulas. Soybean-based formulae are widely used although intolerance to soy has been reported to occur in 15-40% of infants with CMA. The aim of this work was to analyse the in vitro reactivity of the soybean cultivar Raiden, which naturally lacks glycinin A(4)A(5)B(3), to evaluate whether this genotype could be a safe CMP substitute for CMA patients. The reactivity of conventional soybean (CS) and Raiden soybean (RS) genotypes and also recombinant glycinin A(4)A(5)B(3) and alphabeta-conglycinin with casein-specific monoclonal antibodies and CMP-specific polyclonal serum was evaluated by immunoblotting and ELISA. A sequential competitive ELISA with the polyclonal antiserum and different soluble inhibitors was performed. In addition, an indirect ELISA with sera of atopic children with CMA was carried out to analyse the IgE-binding capacity of the different soybean components. We have shown that CS contains four components that cross-react with CMP, while RS has only one. The remaining cross-reactive component in RS was identified as alpha-subunit beta-conglycinin. By means of inhibitory ELISA, we demonstrated that CS, RS and the alpha-subunit beta-conglycinin extracts inhibited the binding of CMP-specific antibodies to the CMP-coated solid phase. Finally, we showed that CS, RS and the recombinant proteins were recognized by human CMP-specific IgE antibodies. This work shows that although Raiden has fewer cross-reactive components than conventional soybean, it still has a residual cross-reactive component: the alpha-subunit beta-conglycinin. This reactivity might make this genotype unsuitable to treat CMA and also explains adverse reactions to soybean in CMA infants.

Influence of Si wafer thinning processes on (sub)surface defects

NASA Astrophysics Data System (ADS)

Inoue, Fumihiro; Jourdain, Anne; Peng, Lan; Phommahaxay, Alain; De Vos, Joeri; Rebibis, Kenneth June; Miller, Andy; Sleeckx, Erik; Beyne, Eric; Uedono, Akira

2017-05-01

Wafer-to-wafer three-dimensional (3D) integration with minimal Si thickness can produce interacting multiple devices with significantly scaled vertical interconnections. Realizing such a thin 3D structure, however, depends critically on the surface and subsurface of the remaining backside Si after the thinning processes. The Si (sub)surface after mechanical grinding has already been characterized fruitfully for a range of few dozen of μm. Here, we expand the characterization of Si (sub)surface to 5 μm thickness after thinning process on dielectric bonded wafers. The subsurface defects and damage layer were investigated after grinding, chemical mechanical polishing (CMP), wet etching and plasma dry etching. The (sub)surface defects were characterized using transmission microscopy, atomic force microscopy, and positron annihilation spectroscopy. Although grinding provides the fastest removal rate of Si, the surface roughness was not compatible with subsequent processing. Furthermore, mechanical damage such as dislocations and amorphous Si cannot be reduced regardless of Si thickness and thin wafer handling systems. The CMP after grinding showed excellent performance to remove this grinding damage, even though the removal amount is 1 μm. For the case of Si thinning towards 5 μm using grinding and CMP, the (sub)surface is atomic scale of roughness without vacancy. For the case of grinding + dry etch, vacancy defects were detected in subsurface around 0.5-2 μm. The finished surface after wet etch remains in the nm scale in the strain region. By inserting a CMP step in between grinding and dry etch it is possible to significantly reduce not only the roughness, but also the remaining vacancies at the subsurface. The surface of grinding + CMP + dry etching gives an equivalent mono vacancy result as to that of grinding + CMP. This combination of thinning processes allows development of extremely thin 3D integration devices with minimal roughness and vacancy surface.

Sensor-based monitoring and inspection of surface morphology in ultraprecision manufacturing processes

NASA Astrophysics Data System (ADS)

Rao, Prahalad Krishna

This research proposes approaches for monitoring and inspection of surface morphology with respect to two ultraprecision/nanomanufacturing processes, namely, ultraprecision machining (UPM) and chemical mechanical planarization (CMP). The methods illustrated in this dissertation are motivated from the compelling need for in situ process monitoring in nanomanufacturing and invoke concepts from diverse scientific backgrounds, such as artificial neural networks, Bayesian learning, and algebraic graph theory. From an engineering perspective, this work has the following contributions: 1. A combined neural network and Bayesian learning approach for early detection of UPM process anomalies by integrating data from multiple heterogeneous in situ sensors (force, vibration, and acoustic emission) is developed. The approach captures process drifts in UPM of aluminum 6061 discs within 15 milliseconds of their inception and is therefore valuable for minimizing yield losses. 2. CMP process dynamics are mathematically represented using a deterministic multi-scale hierarchical nonlinear differential equation model. This process-machine inter-action (PMI) model is evocative of the various physio-mechanical aspects in CMP and closely emulates experimentally acquired vibration signal patterns, including complex nonlinear dynamics manifest in the process. By combining the PMI model predictions with features gathered from wirelessly acquired CMP vibration signal patterns, CMP process anomalies, such as pad wear, and drifts in polishing were identified in their nascent stage with high fidelity (R2 ~ 75%). 3. An algebraic graph theoretic approach for quantifying nano-surface morphology from optical micrograph images is developed. The approach enables a parsimonious representation of the topological relationships between heterogeneous nano-surface fea-tures, which are enshrined in graph theoretic entities, namely, the similarity, degree, and Laplacian matrices. Topological invariant measures (e.g., Fiedler number, Kirchoff index) extracted from these matrices are shown to be sensitive to evolving nano-surface morphology. For instance, we observed that prominent nanoscale morphological changes on CMP processed Cu wafers, although discernible visually, could not be tractably quantified using statistical metrology parameters, such as arithmetic average roughness (Sa), root mean square roughness (Sq), etc. In contrast, CMP induced nanoscale surface variations were captured on invoking graph theoretic topological invariants. Consequently, the graph theoretic approach can enable timely, non-contact, and in situ metrology of semiconductor wafers by obviating the need for reticent profile mapping techniques (e.g., AFM, SEM, etc.), and thereby prevent the propagation of yield losses over long production runs.

Neural networks and MIMD-multiprocessors

NASA Technical Reports Server (NTRS)

Vanhala, Jukka; Kaski, Kimmo

1990-01-01

Two artificial neural network models are compared. They are the Hopfield Neural Network Model and the Sparse Distributed Memory model. Distributed algorithms for both of them are designed and implemented. The run time characteristics of the algorithms are analyzed theoretically and tested in practice. The storage capacities of the networks are compared. Implementations are done using a distributed multiprocessor system.

Multiprocessor programming environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, M.B.; Fornaro, R.

Programming tools and techniques have been well developed for traditional uniprocessor computer systems. The focus of this research project is on the development of a programming environment for a high speed real time heterogeneous multiprocessor system, with special emphasis on languages and compilers. The new tools and techniques will allow a smooth transition for programmers with experience only on single processor systems.

Shared Versus Distributed Memory Multiprocessors

DTIC Science & Technology

1991-01-01

multiprocessors should hawe shared or dis.trimuted meieo-% ha~ trr ~ g ’’~ de~i c4~accio;, S Cm teaicners argue S trongly tor Outiding (li15 tri huted...Applications, MIT Press (1985). 161 D. Gajski et el., "Cedar," Proc. Compcon, pp. 306-309 (Spring 19S9). 171 S. Ahuja, N. Carriero and D. Gelernter, "Linda

The Minerva Multi-Microprocessor.

DTIC Science & Technology

A multiprocessor system is described which is an experiment in low cost, extensible, multiprocessor architectures. Global issues such as inclusion of a central bus, design of the bus arbiter, and methods of interrupt handling are considered. The system initially includes two processor types, based on microprocessors, and these are discussed. Methods for reducing processor demand for the central bus are described.

FTMP - A highly reliable Fault-Tolerant Multiprocessor for aircraft

NASA Technical Reports Server (NTRS)

Hopkins, A. L., Jr.; Smith, T. B., III; Lala, J. H.

1978-01-01

The FTMP (Fault-Tolerant Multiprocessor) is a complex multiprocessor computer that employs a form of redundancy related to systems considered by Mathur (1971), in which each major module can substitute for any other module of the same type. Despite the conceptual simplicity of the redundancy form, the implementation has many intricacies owing partly to the low target failure rate, and partly to the difficulty of eliminating single-fault vulnerability. An extensive analysis of the computer through the use of such modeling techniques as Markov processes and combinatorial mathematics shows that for random hard faults the computer can meet its requirements. It is also shown that the maintenance scheduled at intervals of 200 hr or more can be adequate most of the time.

77 FR 68748 - Intent To Prepare a Draft Environmental Impact Statement and Feasibility Report for the Cano...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-16

... recreation and tourism, with minimal temporary negative impact on the ecosystem and the adjacent communities... public spaces for recreation and interaction between the communities, visitors and the CMP identified as... impoverished communities in San Juan, the CMP connects the San Juan Bay with the San Jose and Los Corozos...

75 FR 14548 - Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Comprehensive Ecosystem-Based...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-26

... the FMP for Coastal Migratory Pelagic (CMP) Resources (CMP FMP); and the FMP for the Spiny Lobster Fishery of the Gulf of Mexico and South Atlantic (Spiny Lobster FMP), as prepared and submitted by the... bottom habitats; dolphin and wahoo; golden crab; shrimp; spiny lobster; and snapper-grouper off the...

75 FR 35330 - Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Comprehensive Ecosystem-Based...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-22

... Migratory Pelagic (CMP) Resources (CMP FMP); and the FMP for the Spiny Lobster Fishery of the Gulf of Mexico and South Atlantic (Spiny Lobster FMP), as prepared and submitted by the South Atlantic and Gulf of...; shrimp; spiny lobster; and snapper-grouper off the southern Atlantic states are managed under their...

Controlled mass pollination in loblolly pine to increase genetic gains

Treesearch

F.E. Bridgwater; D.L. Bramlett; T.D. Byram; W.J. Lowe

1998-01-01

Controlled mass pollination (CMP) is one way to increase genetic gains from traditional wind-pollinated seed orchards. Methodology is under development by several forestry companies in the southern USA. Costs of CMP depend on the efficient installation, pollination, and removal of inexpensive paper bags. Even in pilot-scale studies these costs seem reasonable. Net...

Condensed Matter Physics at ONR - A Nanoelectronics Perspective

NASA Astrophysics Data System (ADS)

Baatar, Chagaan

As a mission agency within the Department of Defense, the Office of Naval Research (ONR) currently does not have a program exclusively dedicated to condensed matter physics (CMP) research. Yet many CMP related topics are being funded under various programs scattered throughout the agency. In this talk I will provide an example of such a program - the ONR Nanoelectronics program, that I currently manage, and highlight some of the CMP related activities within the program. I may also mention a few topics that are funded by other ONR program officers. Finally, in addressing the theme of the session, I will describe the ONR Young Investigator Program (YIP) - its brief history, solicitation and evaluation processes involved, and provide a few examples from recent YIP projects.

Development of High-Speed Copper Chemical Mechanical Polishing Slurry for Through Silicon Via Application Based on Friction Analysis Using Atomic Force Microscope

NASA Astrophysics Data System (ADS)

Amanokura, Jin; Ono, Hiroshi; Hombo, Kyoko

2011-05-01

In order to obtain a high-speed copper chemical mechanical polishing (CMP) process for through silicon vias (TSV) application, we developed a new Cu CMP slurry through friction analysis of Cu reaction layer by an atomic force microscope (AFM) technique. A lateral modulation friction force microscope (LM-FFM) is able to measure the friction value properly giving a vibration to the layer. We evaluated the torsional displacement between the probe of the LM-FFM and the Cu reaction layer under a 5 nm vibration to cancel the shape effect of the Cu reaction layer. The developed Cu CMP slurry forms a frictionally easy-removable Cu reaction layer.

Minimum area requirements for an at-risk butterfly based on movement and demography.

PubMed

Brown, Leone M; Crone, Elizabeth E

2016-02-01

Determining the minimum area required to sustain populations has a long history in theoretical and conservation biology. Correlative approaches are often used to estimate minimum area requirements (MARs) based on relationships between area and the population size required for persistence or between species' traits and distribution patterns across landscapes. Mechanistic approaches to estimating MAR facilitate prediction across space and time but are few. We used a mechanistic MAR model to determine the critical minimum patch size (CMP) for the Baltimore checkerspot butterfly (Euphydryas phaeton), a locally abundant species in decline along its southern range, and sister to several federally listed species. Our CMP is based on principles of diffusion, where individuals in smaller patches encounter edges and leave with higher probability than those in larger patches, potentially before reproducing. We estimated a CMP for the Baltimore checkerspot of 0.7-1.5 ha, in accordance with trait-based MAR estimates. The diffusion rate on which we based this CMP was broadly similar when estimated at the landscape scale (comparing flight path vs. capture-mark-recapture data), and the estimated population growth rate was consistent with observed site trends. Our mechanistic approach to estimating MAR is appropriate for species whose movement follows a correlated random walk and may be useful where landscape-scale distributions are difficult to assess, but demographic and movement data are obtainable from a single site or the literature. Just as simple estimates of lambda are often used to assess population viability, the principles of diffusion and CMP could provide a starting place for estimating MAR for conservation. © 2015 Society for Conservation Biology.

Redox-active triazatruxene-based conjugated microporous polymers for high-performance supercapacitors† †Electronic supplementary information (ESI) available: Synthetic procedures and characterization data for all new compounds; general experimental method; thermogravimetry curves; PXRD patterns; SEM and TEM images; XPS spectra. See DOI: 10.1039/c6sc05532j Click here for additional data file.

PubMed Central

Li, Xiang-Chun; Zhang, Yizhou; Wang, Chun-Yu; Wan, Yi

2017-01-01

Conjugated polymers (CPs) have been intensively explored for various optoelectronic applications in the last few decades. Nevertheless, CP based electrochemical energy storage devices such as supercapacitors remain largely unexplored. This is mainly owing to the low specific capacitance, poor structural/electrochemical stability, and low energy density of most existing CPs. In this contribution, a novel set of redox-active conjugated microporous polymers, TAT-CMP-1 and TAT-CMP-2, based on nitrogen-rich and highly conductive triazatruxene building blocks, were successfully designed and synthesized to explore their potential application as efficient and stable electrode materials for supercapacitors. Despite a moderate surface area of 88 m2 g–1 for TAT-CMP-1 and 106 m2 g–1 for TAT-CMP-2, exceptional specific capacitances of 141 F g–1 and 183 F g–1 were achieved at a current density of 1 A g–1. The resulting polymers exhibited unusually high areal specific capacitance (>160 μF cm–2), which is attributed to the pseudocapacitance resulting from redox-active structures with high nitrogen content. More importantly, the TAT-CMP-2 electrode exhibits excellent cycling stability: only 5% capacitance fading is observed after 10 000 cycles at a high current density of 10 A g–1, enabling the possible use of these materials as electrodes in electrochemical devices. PMID:28451362

A prime-boost immunization regimen based on a simian adenovirus 36 vectored multi-stage malaria vaccine induces protective immunity in mice.

PubMed

Fonseca, Jairo A; McCaffery, Jessica N; Kashentseva, Elena; Singh, Balwan; Dmitriev, Igor P; Curiel, David T; Moreno, Alberto

2017-05-31

Malaria remains a considerable burden on public health. In 2015, the WHO estimates there were 212 million malaria cases causing nearly 429,000 deaths globally. A highly effective malaria vaccine is needed to reduce the burden of this disease. We have developed an experimental vaccine candidate (PyCMP) based on pre-erythrocytic (CSP) and erythrocytic (MSP1) stage antigens derived from the rodent malaria parasite P. yoelii. Our protein-based vaccine construct induces protective antibodies and CD4 + T cell responses. Based on evidence that viral vectors increase CD8 + T cell-mediated immunity, we also have tested heterologous prime-boost immunization regimens that included human adenovirus serotype 5 vector (Ad5), obtaining protective CD8 + T cell responses. While Ad5 is commonly used for vaccine studies, the high prevalence of pre-existing immunity to Ad5 severely compromises its utility. Here, we report the use of the novel simian adenovirus 36 (SAd36) as a candidate for a vectored malaria vaccine since this virus is not known to infect humans, and it is not neutralized by anti-Ad5 antibodies. Our study shows that the recombinant SAd36PyCMP can enhance specific CD8 + T cell response and elicit similar antibody titers when compared to an immunization regimen including the recombinant Ad5PyCMP. The robust immune responses induced by SAd36PyCMP are translated into a lower parasite load following P. yoelii infectious challenge when compared to mice immunized with Ad5PyCMP. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of apical enlargement and complementary canal preparation with the Self-Adjusting File on endotoxin reduction in retreatment cases.

PubMed

Silva, E J N L; Ferreira, V M; Silva, C C; Herrera, D R; De-Deus, G; Gomes, B P

2017-07-01

To compare the effectiveness of large apical preparations and complementary canal preparation with the Self-Adjusting File (SAF) in removing endotoxins from the root canal of teeth with apical periodontitis. Ten single-rooted and single-canaled teeth with post-treatment apical periodontitis were selected. Endotoxin samples were taken after removal of the root filling (S1), after chemomechanical preparation (CMP) using 2.5% NaOCl and an R25 file (S2), after CMP using 2.5% NaOCl and an R40 file (S3) and after complementary CMP using the SAF system (S4). Limulus amebocyte lysate (LAL) was used to measure endotoxin levels. The Friedman and Wilcoxon tests were used to compare endotoxin levels at each clinical intervention (P < 0.05). After root filling removal, endotoxin was detected in 100% of the root canals (S1, 4.84 EU mL -1 ). CMP with the R25 file was able to significantly reduce endotoxin levels (P < 0.05). Increased levels of endotoxin removal were achieved by apical preparation with the R40 file (P < 0.05). Complementary CMP with SAF did not significantly reduce endotoxin levels (P > 0.05) following the use of the R40 instrument. Apical enlargement protocols were effective in significantly reducing endotoxin levels. Complementary preparation with the SAF system failed to eliminate residual endotoxin contents beyond those obtained with the R40 instrument. © 2016 International Endodontic Journal. Published by John Wiley & Sons Ltd.

The Community Mentorship Program: Providing Community-Engagement Opportunities for Early-Stage Clinical and Translational Scientists to Facilitate Research Translation.

PubMed

Patino, Cecilia M; Kubicek, Katrina; Robles, Marisela; Kiger, Holly; Dzekov, Jeanne

2017-02-01

A goal of the Southern California Clinical and Translational Science Institute (SC-CTSI) at the University of Southern California and Children's Hospital Los Angeles is to train early-stage clinical and translational scientists (CTSs) to conduct research that improves the health of diverse communities. This goal aligns well with the Institute of Medicine's recommendations emphasizing community engagement in biomedical research that facilitates research translation. The Community Mentorship Program (CMP), created to complement community-engaged research didactics, matches CTSs with community mentors who help them identify and complete community-engaged experiences that inform their research. The CMP was piloted in 2013-2015 by the SC-CTSI Workforce Development and Community Engagement cores. The CMP team matched three CTSs (assistant professors pursuing mentored career development awards) with mentors at community-based organizations (CBOs) aligned with their research interests. Each mentor-mentee pair signed a memorandum of understanding. The CMP team checked in regularly, monitoring progress and addressing challenges in CTSs' completion of their community-engaged experience. Each pair completed at least one community-engaged activity informing the CTS's research. In exit interviews, the CTSs and CBO mentors expressed satisfaction with the program and stated that they would continue to work together. The CTSs reported that the program provided opportunities to develop networks outside academia, build trust within the community, and receive feedback and learn from individuals in communities affected by their research. The CMP will be expanded to include all eligible early-career CTSs and promoted for use in similar settings outside the SC-CTSI.

Investigation of aluminum gate CMP in a novel alkaline solution

NASA Astrophysics Data System (ADS)

Cuiyue, Feng; Yuling, Liu; Ming, Sun; Wenqian, Zhang; Jin, Zhang; Shuai, Wang

2016-01-01

Beyond 45 nm, due to the superior CMP performance requirements with the metal gate of aluminum in the advanced CMOS process, a novel alkaline slurry for an aluminum gate CMP with poly-amine alkali slurry is investigated. The aluminum gate CMP under alkaline conditions has two steps: stock polishing and fine polishing. A controllable removal rate, the uniformity of aluminum gate and low corrosion are the key challenges for the alkaline polishing slurry of the aluminum gate CMP. This work utilizes the complexation-soluble function of FA/O II and the preference adsorption mechanism of FA/O I nonionic surfactant to improve the uniformity of the surface chemistry function with the electrochemical corrosion research, such as OCP-TIME curves, Tafel curves and AC impedance. The result is that the stock polishing slurry (with SiO2 abrasive) contains 1 wt.% H2O2,0.5 wt.% FA/O II and 1.0 wt.% FA/O I nonionic surfactant. For a fine polishing process, 1.5 wt.% H2O2, 0.4 wt.% FA/O II and 2.0 wt.% FA/O I nonionic surfactant are added. The polishing experiments show that the removal rates are 3000 ± 50 Å/min and 1600 ± 60 Å/min, respectively. The surface roughnesses are 2.05 ± 0.128 nm and 1.59 ± 0.081 nm, respectively. A combination of the functions of FA/O II and FA/O I nonionic surfactant obtains a controllable removal rate and a better surface roughness in alkaline solution.

Benchmarking GNU Radio Kernels and Multi-Processor Scheduling

DTIC Science & Technology

2013-01-14

AMD E350 APU , comparable to Atom • ARM Cortex A8 running on a Gumstix Overo on an Ettus USRP E110 The general testing procedure consists of • Build...Intel Atom, and the AMD E350 APU . 3.2 Multi-Processor Scheduling Figure 1: GFLOPs per second through an FFT array on an Intel i7. Example output from

A Real-Time Linux for Multicore Platforms

DTIC Science & Technology

2013-12-20

under ARO support) to obtain a fully-functional OS for supporting real-time workloads on multicore platforms. This system, called LITMUS -RT...to be specified as plugin components. LITMUS -RT is open-source software (available at The views, opinions and/or findings contained in this report... LITMUS -RT (LInux Testbed for MUltiprocessor Scheduling in Real-Time systems), allows different multiprocessor real-time scheduling and

Considerations for Multiprocessor Topologies

NASA Technical Reports Server (NTRS)

Byrd, Gregory T.; Delagi, Bruce A.

1987-01-01

Choosing a multiprocessor interconnection topology may depend on high-level considerations, such as the intended application domain and the expected number of processors. It certainly depends on low-level implementation details, such as packaging and communications protocols. The authors first use rough measures of cost and performance to characterize several topologies. They then examine how implementation details can affect the realizable performance of a topology.

Variation in the Use of Federal and State Civil Money Penalties for Nursing Homes

ERIC Educational Resources Information Center

Harrington, Charlene; Tsoukalas, Theodore; Rudder, Cynthia; Mollot, Richard J.; Carrillo, Helen

2008-01-01

Purpose: The study examined factors associated with state variations in the use of federal and state civil money penalties (CMPs) for nursing homes. Design and Methods: We collected federal and state CMP data from state survey and certification agencies for 2004. We also used federal CMP data from the federal enforcement action database for…

An Injectable Enzymatically Crosslinked Carboxymethylated Pullulan/Chondroitin Sulfate Hydrogel for Cartilage Tissue Engineering

PubMed Central

Chen, Feng; Yu, Songrui; Liu, Bing; Ni, Yunzhou; Yu, Chunyang; Su, Yue; Zhu, Xinyuan; Yu, Xiaowei; Zhou, Yongfeng; Yan, Deyue

2016-01-01

In this study, an enzymatically cross-linked injectable and biodegradable hydrogel system comprising carboxymethyl pullulan-tyramine (CMP-TA) and chondroitin sulfate-tyramine (CS-TA) conjugates was successfully developed under physiological conditions in the presence of both horseradish peroxidase (HRP) and hydrogen peroxide (H2O2) for cartilage tissue engineering (CTTE). The HRP crosslinking method makes this injectable system feasible, minimally invasive and easily translatable for regenerative medicine applications. The physicochemical properties of the mechanically stable hydrogel system can be modulated by varying the weight ratio and concentration of polymer as well as the concentrations of crosslinking reagents. Additionally, the cellular behaviour of porcine auricular chondrocytes encapsulated into CMP-TA/CS-TA hydrogels demonstrates that the hydrogel system has a good cyto-compatibility. Specifically, compared to the CMP-TA hydrogel, these CMP-TA/CS-TA composite hydrogels have enhanced cell proliferation and increased cartilaginous ECM deposition, which significantly facilitate chondrogenesis. Furthermore, histological analysis indicates that the hydrogel system exhibits acceptable tissue compatibility by using a mouse subcutaneous implantation model. Overall, the novel injectable pullulan/chondroitin sulfate composite hydrogels presented here are expected to be useful biomaterial scaffold for regenerating cartilage tissue. PMID:26817622

Surfactant assisted disperser pretreatment on the liquefaction of Ulva reticulata and evaluation of biodegradability for energy efficient biofuel production through nonlinear regression modelling.

PubMed

Kumar, M Dinesh; Tamilarasan, K; Kaliappan, S; Banu, J Rajesh; Rajkumar, M; Kim, Sang Hyoun

2018-05-01

The present study aimed to increase the disintegration potential of marine macroalgae, (Ulva reticulata) through chemo mechanical pretreatment (CMP) in an energy efficient manner. By combining surfactant with disperser, the specific energy input was considerably reduced from 437.1 kJ/kg TS to 264.9 kJ/kg TS to achieve 10.7% liquefaction. A disperser rpm (10,000), pretreatment time (30 min) and tween 80 dosage (21.6 mg/L) were considered as an optimum for effective liquefaction of algal biomass. CMP was designated as an appropriate pretreatment resulting in a higher soluble organic release 1250 mg/L, respectively. Anaerobic fermentation results revealed that the volatile fatty acid (VFA) concentration was doubled (782 mg/L) in CMP when compared to mechanical pretreatment (MP) (345 mg/L). CMP pretreated algal biomass was considered as the suitable for biohydrogen production with highest H 2 yield of about 63 mL H 2 /g COD than (MP) (45 mL H 2 /g COD) and control (10 mL H 2 /g COD). Copyright © 2018 Elsevier Ltd. All rights reserved.

Association of Calf Muscle Pump Stimulation With Sleep Quality in Adults.

PubMed

Baniak, Lynn M; Pierce, Carolyn S; McLeod, Kenneth J; Chasens, Eileen R

2016-12-01

Prevention of lower extremity fluid pooling (LEFP) is associated with improved sleep quality. Physical activity and compression stockings are non-invasive methods used to manage LEFP, but both are associated with low adherence. Calf muscle pump (CMP) stimulation is an alternative and more convenient approach. Convenience sampling was used to recruit 11 participants between ages 45 and 65 with poor sleep quality. A within-person single-group pre-test-post-test design was used to evaluate changes in sleep quality, daytime sleepiness, and functional outcomes sensitive to impaired sleep as measured by the Pittsburgh Sleep Quality Index (PSQI), Functional Outcomes of Sleep Questionnaire, and Epworth Sleepiness Scale after 4 weeks of CMP stimulation. Statistical analysis included effect size (ES) calculations. After daily use of CMP stimulation, participants demonstrated improvement in overall sleep quality (ES = -.97) and a large reduction in daily disturbance from poor sleep (ES = -1.25). Moderate improvements were observed in daytime sleepiness (ES = -.53) and functional outcomes sensitive to sleepiness (ES = .49). Although causality could not be determined with this study design, these results support further research to determine whether CMP stimulation can improve sleep quality. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

An Injectable Enzymatically Crosslinked Carboxymethylated Pullulan/Chondroitin Sulfate Hydrogel for Cartilage Tissue Engineering

NASA Astrophysics Data System (ADS)

Chen, Feng; Yu, Songrui; Liu, Bing; Ni, Yunzhou; Yu, Chunyang; Su, Yue; Zhu, Xinyuan; Yu, Xiaowei; Zhou, Yongfeng; Yan, Deyue

2016-01-01

In this study, an enzymatically cross-linked injectable and biodegradable hydrogel system comprising carboxymethyl pullulan-tyramine (CMP-TA) and chondroitin sulfate-tyramine (CS-TA) conjugates was successfully developed under physiological conditions in the presence of both horseradish peroxidase (HRP) and hydrogen peroxide (H2O2) for cartilage tissue engineering (CTTE). The HRP crosslinking method makes this injectable system feasible, minimally invasive and easily translatable for regenerative medicine applications. The physicochemical properties of the mechanically stable hydrogel system can be modulated by varying the weight ratio and concentration of polymer as well as the concentrations of crosslinking reagents. Additionally, the cellular behaviour of porcine auricular chondrocytes encapsulated into CMP-TA/CS-TA hydrogels demonstrates that the hydrogel system has a good cyto-compatibility. Specifically, compared to the CMP-TA hydrogel, these CMP-TA/CS-TA composite hydrogels have enhanced cell proliferation and increased cartilaginous ECM deposition, which significantly facilitate chondrogenesis. Furthermore, histological analysis indicates that the hydrogel system exhibits acceptable tissue compatibility by using a mouse subcutaneous implantation model. Overall, the novel injectable pullulan/chondroitin sulfate composite hydrogels presented here are expected to be useful biomaterial scaffold for regenerating cartilage tissue.

Enhanced degradation and mineralization of 4-chloro-3-methyl phenol by Zn-CNTs/O3 system.

PubMed

Liu, Yong; Zhou, Anlan; Liu, Yanlan; Wang, Jianlong

2018-01-01

A novel zinc-carbon nanotubes (Zn-CNTs) composite was prepared, characterized and used in O 3 system for the enhanced degradation and mineralization of chlorinated phenol. The Zn-CNTs was characterized by SEM, BET and XRD, and the degradation of 4-chloro-3-methyl phenol (CMP) in aqueous solution was investigated using Zn-CNTs/O 3 system. The experimental results showed that the rate constant of total organic carbon (TOC) removal was 0.29 min -1 , much higher than that of only O 3 system (0.059 min -1 ) because Zn-CNTs/O 2 system could generate H 2 O 2 in situ, the concentration of H 2 O 2 could reach 156.14 mg/L within 60 min at pH 6.0. The high mineralization ratio of CMP by Zn-CNTs/O 3 occurred at wide pH range (3.0-9.0). The increase of Zn-CNTs dosage or gas flow rate contributed to the enhancement of CMP mineralization. The intermediates of CMP degradation were identified and the possible degradation pathway was tentatively proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fabrication of controllably variable sub-100  nm gaps in silver nanowires by photothermal-induced stress.

PubMed

Ghosh, Pintu; Lu, Jinsheng; Luo, Hao; Xu, Ziquan; Yan, Xiaoyuan; Wang, Yewu; Lu, Jun; Qiu, Min; Li, Qiang

2018-05-15

A technique to fabricate nanogaps with controllably variable gap width in silver (Ag) nanowires (NWs) by photothermal-induced stress utilizing a focused continuous-wave laser (532 nm) is presented. For the case of an Ag NW on gold thin film, a gap width starting from ∼20  nm is achieved with a critical minimum power (CMP) of about 160 mW, whereas in the case of an Ag NW placed on top of a zinc oxide NW, the attained gap width is as small as a few nm (<10  nm) with a CMP of only ∼100  mW. In both cases, the CMP is much lower as compared to the required CMP (∼280  mW) for an Ag NW placed on a bare silica substrate. The photothermal-induced stress combined with Rayleigh instability, melting, and sublimation of Ag aids in breaking the Ag NW. In particular, the former one plays a key role in attaining an extremely narrow gap. This technique to fabricate sub-100 nm nanogaps in metal NWs can be extensively implemented in fabrication and maintenance of nanomechanical, nanoplasmonic, and nanoelectronic devices.

A multiprocessor computer simulation model employing a feedback scheduler/allocator for memory space and bandwidth matching and TMR processing

NASA Technical Reports Server (NTRS)

Bradley, D. B.; Irwin, J. D.

1974-01-01

A computer simulation model for a multiprocessor computer is developed that is useful for studying the problem of matching multiprocessor's memory space, memory bandwidth and numbers and speeds of processors with aggregate job set characteristics. The model assumes an input work load of a set of recurrent jobs. The model includes a feedback scheduler/allocator which attempts to improve system performance through higher memory bandwidth utilization by matching individual job requirements for space and bandwidth with space availability and estimates of bandwidth availability at the times of memory allocation. The simulation model includes provisions for specifying precedence relations among the jobs in a job set, and provisions for specifying precedence execution of TMR (Triple Modular Redundant and SIMPLEX (non redundant) jobs.

Dataflow computing approach in high-speed digital simulation

NASA Technical Reports Server (NTRS)

Ercegovac, M. D.; Karplus, W. J.

1984-01-01

New computational tools and methodologies for the digital simulation of continuous systems were explored. Programmability, and cost effective performance in multiprocessor organizations for real time simulation was investigated. Approach is based on functional style languages and data flow computing principles, which allow for the natural representation of parallelism in algorithms and provides a suitable basis for the design of cost effective high performance distributed systems. The objectives of this research are to: (1) perform comparative evaluation of several existing data flow languages and develop an experimental data flow language suitable for real time simulation using multiprocessor systems; (2) investigate the main issues that arise in the architecture and organization of data flow multiprocessors for real time simulation; and (3) develop and apply performance evaluation models in typical applications.

Design and evaluation of a fault-tolerant multiprocessor using hardware recovery blocks

NASA Technical Reports Server (NTRS)

Lee, Y. H.; Shin, K. G.

1982-01-01

A fault-tolerant multiprocessor with a rollback recovery mechanism is discussed. The rollback mechanism is based on the hardware recovery block which is a hardware equivalent to the software recovery block. The hardware recovery block is constructed by consecutive state-save operations and several state-save units in every processor and memory module. When a fault is detected, the multiprocessor reconfigures itself to replace the faulty component and then the process originally assigned to the faulty component retreats to one of the previously saved states in order to resume fault-free execution. A mathematical model is proposed to calculate both the coverage of multi-step rollback recovery and the risk of restart. A performance evaluation in terms of task execution time is also presented.

Medicare program; contracts with health maintenance organizations (HMOs) and competitive medical plans (CMPs)--HCFA. Final rule with comment period.

PubMed

1995-09-01

This rule clarifies and updates portions of the HCFA regulations that pertain to the following: The conditions that an HMO or CMP must meet to qualify for a Medicare contract (Subpart J). The contract requirements (Subpart L). The rules for enrollment, entitlement, and disenrollment of Medicare beneficiaries in a contracting HMO or CMP (Subpart K). How a Medicare contract is affected when there is change of ownership or leasing of facilities of a contracting HMO or CMP (Subpart M). These are technical and editorial changes that do not affect the substance of the regulations. They are intended to make it easier to find particular provisions, to provide overviews of the different program aspects, and to better ensure uniform understanding of the rules.

Cow's milk allergy: where have we come from and where are we going?

PubMed

Host, Arne; Halken, Susanne

2014-03-01

Since the 1930's the scientific literature on cow's milk protein allergy (CMPA) has accumulated. Over the last decade new diagnostic tools and treatment approaches have been developed. The diagnosis of reproducible adverse reactions to cow's milk proteins (CMP), i.e. CMPA, still has to be confirmed by controlled elimination and challenge procedures. Advanced diagnostic testing using epitope and microarray technology may in the future improve the diagnostic accuracy of CMPA by determination of specific IgE against specific allergen components of cow's milk protein. The incidence of CMPA in early childhood is approximately 2-3% in developed countries. Symptoms suggestive of CMPA may be encountered in 5-15% of infants emphasizing the importance of controlled elimination/milk challenge procedures. Reproducible clinical reactions to CMP in human milk have been reported in 0.5% of breastfed infants. Most infants with CMPA develop symptoms before 1 month of age, often within 1 week after inter introduction of CMP-based formula. The majority has two or more symptoms from two or more organ systems. Approximately 50-70% have cutaneous symptoms, 50-60% gastrointestinal symptoms and 20-30% respiratory symptoms. Symptoms may occur within 1 hour after milk intake (immediate reactions) or after 1 hour (late reactions). The prognosis of CMPA is good with a remission rate of approximately 45 to 50% at 1 year, 60 to 75% at 2 years and 85 to 90% at 3 years. Associated adverse reactions to other foods develop in up to 50% and allergy against inhalants in 50 to 80%. The basic treatment of CMPA is avoidance of CMP. In early childhood a milk substitute is needed. Documented extensively hydrolysed formulas are recommended, whereas partially hydrolysed formulas should not be used because of a high degree of antigenicity and allergenicity associated with adverse reactions. In case of intolerance to extensively hydrolysed formulas and multiple food allergies a formula based on aminoacids is recommended. Alternative milk substitutes such as sheep's and goat's milk should not be used because of a high degree of cross reactivity with CMP. Milk from other mammals such as mare and donkey may be tolerated by some children with CMPA. Soy protein is as allergenic as CMP and soy formula is not recommended for young children with CMPA because of a great risk of development of allergy to soy, whereas soymilk is normally tolerated in older children with CMPA. Recent treatment modalities are oral immunotherapy (OIT) involving the ingestion of increasing amounts of milk allergen on a regular basis to desensitize and potentially permanently tolerize patients to CMP. OIT can increase the reaction thresholds to CMP, but questions about safety and long-term efficacy remain. Anti-IgE therapy with Omalizumab may improve the safety and efficacy of OIT and may provide benefit in monotherapy.

Exploring personality dimensions that influence practice and performance of a simulated laparoscopic task in the objective structured clinical examination.

PubMed

Malhotra, Neha; Poolton, Jamie M; Wilson, Mark R; Leung, Gilberto; Zhu, Frank; Fan, Joe K M; Masters, Rich S W

2015-01-01

Surgical educators have encouraged the investigation of individual differences in aptitude and personality in surgical performance. An individual personality difference that has been shown to influence laparoscopic performance under time pressure is movement specific reinvestment. Movement specific reinvestment has 2 dimensions, movement self-consciousness (MS-C) (i.e., the propensity to consciously monitor movements) and conscious motor processing (CMP) (i.e., the propensity to consciously control movements), which have been shown to differentially influence laparoscopic performance in practice but have yet to be investigated in the context of psychological stress (e.g., the objective structured clinical examination [OSCE]). This study investigated the role of individual differences in propensity for MS-C and CMP in practice of a fundamental laparoscopic skill and in laparoscopic performance during the OSCE. Furthermore, this study examined whether individual differences during practice of a fundamental laparoscopic skill were predictive of laparoscopic performance during the OSCE. Overall, 77 final-year undergraduate medical students completed the movement specific reinvestment scale, an assessment tool that quantifies the propensity for MS-C and CMP. Participants were trained to proficiency on a fundamental laparoscopic skill. The number of trials to reach proficiency was measured, and completion times were recorded during early practice, later practice, and the OSCE. There was a trend for CMP to be negatively associated with the number of trials to reach proficiency (p = 0.064). A higher propensity for CMP was associated with fewer trials to reach proficiency (β = -0.70, p = 0.023). CMP and MS-C did not significantly predict completion times in the OSCE (p > 0.05). Completion times in early practice (β = 0.05, p = 0.016) and later practice (β = 0.47, p < 0.001) and number of trials to reach proficiency (β = 0.23, p = 0.003) significantly predicted completion times in the OSCE. It appears that a higher propensity for CMP predicts faster rates of learning of a fundamental laparoscopic skill. Furthermore, laparoscopic performance during practice is indicative of laparoscopic performance in the challenging conditions of the OSCE. The lack of association between the 2 dimensions of movement specific reinvestment and performance during the OSCE is explained using the theory of reinvestment as a framework. Overall, consideration of personality differences and individual differences in ability during practice could help inform the development of individualized surgical training programs. Copyright © 2015 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Bibliography On Multiprocessors And Distributed Processing

NASA Technical Reports Server (NTRS)

Miya, Eugene N.

1988-01-01

Multiprocessor and Distributed Processing Bibliography package consists of large machine-readable bibliographic data base, which in addition to usual keyword searches, used for producing citations, indexes, and cross-references. Data base contains UNIX(R) "refer" -formatted ASCII data and implemented on any computer running under UNIX(R) operating system. Easily convertible to other operating systems. Requires approximately one megabyte of secondary storage. Bibliography compiled in 1985.

Method for wiring allocation and switch configuration in a multiprocessor environment

DOEpatents

Aridor, Yariv [Zichron Ya'akov, IL; Domany, Tamar [Kiryat Tivon, IL; Frachtenberg, Eitan [Jerusalem, IL; Gal, Yoav [Haifa, IL; Shmueli, Edi [Haifa, IL; Stockmeyer, legal representative, Robert E.; Stockmeyer, Larry Joseph [San Jose, CA

2008-07-15

A method for wiring allocation and switch configuration in a multiprocessor computer, the method including employing depth-first tree traversal to determine a plurality of paths among a plurality of processing elements allocated to a job along a plurality of switches and wires in a plurality of D-lines, and selecting one of the paths in accordance with at least one selection criterion.

Generic Software for Emulating Multiprocessor Architectures.

DTIC Science & Technology

1985-05-01

RD-A157 662 GENERIC SOFTWARE FOR EMULATING MULTIPROCESSOR 1/2 AlRCHITECTURES(J) MASSACHUSETTS INST OF TECH CAMBRIDGE U LRS LAB FOR COMPUTER SCIENCE R...AREA & WORK UNIT NUMBERS MIT Laboratory for Computer Science 545 Technology Square Cambridge, MA 02139 ____________ I I. CONTROLLING OFFICE NAME AND...aide If neceeasy end Identify by block number) Computer architecture, emulation, simulation, dataf low 20. ABSTRACT (Continue an reverse slde It

Adaptive Backoff Synchronization Techniques

DTIC Science & Technology

1989-07-01

The Simple Code. Technical Report, Lawrence Livermore Laboratory, February 1978. [6] F. Darems-Rogers, D. A. George, V. A. Norton, and G . F. Pfister...Heights, November 1986. 20 [7] Daniel Gajski , David Kuck, Duncan Lawrie, and Ahmed Saleh. Cedar - A Large Scale Multiprocessor. In International...17] Janak H. Patel. Analysis of Multiprocessors with Private Cache Memories. IEEE Transactions on Com- puters, C-31(4):296-304, April 1982. [18] G

Three-Dimensional Vibration Isolator for Suppressing High-Frequency Responses for Sage III Contamination Monitoring Package (CMP)

NASA Technical Reports Server (NTRS)

Li, Y.; Cutright, S.; Dyke, R.; Templeton, J.; Gasbarre, J.; Novak, F.

2015-01-01

The Stratospheric Aerosol and Gas Experiment (SAGE) III - International Space Station (ISS) instrument will be used to study ozone, providing global, long-term measurements of key components of the Earth's atmosphere for the continued health of Earth and its inhabitants. SAGE III is launched into orbit in an inverted configuration on SpaceX;s Falcon 9 launch vehicle. As one of its four supporting elements, a Contamination Monitoring Package (CMP) mounted to the top panel of the Interface Adapter Module (IAM) box experiences high-frequency response due to structural coupling between the two structures during the SpaceX launch. These vibrations, which were initially observed in the IAM Engineering Development Unit (EDU) test and later verified through finite element analysis (FEA) for the SpaceX launch loads, may damage the internal electronic cards and the Thermoelectric Quartz Crystal Microbalance (TQCM) sensors mounted on the CMP. Three-dimensional (3D) vibration isolators were required to be inserted between the CMP and IAM interface in order to attenuate the high frequency vibrations without resulting in any major changes to the existing system. Wire rope isolators were proposed as the isolation system between the CMP and IAM due to the low impact to design. Most 3D isolation systems are designed for compression and roll, therefore little dynamic data was available for using wire rope isolators in an inverted or tension configuration. From the isolator FEA and test results, it is shown that by using the 3D wire rope isolators, the CMP high-frequency responses have been suppressed by several orders of magnitude over a wide excitation frequency range. Consequently, the TQCM sensor responses are well below their qualification environments. It is indicated that these high-frequency responses due to the typical instrument structural coupling can be significantly suppressed by a vibration passive control using the 3D vibration isolator. Thermal and contamination issues were also examined during the isolator selection period for meeting the SAGE III-ISS instrument requirements.

Framework for analysis of guaranteed QOS systems

NASA Astrophysics Data System (ADS)

Chaudhry, Shailender; Choudhary, Alok

1997-01-01

Multimedia data is isochronous in nature and entails managing and delivering high volumes of data. Multiprocessors with their large processing power, vast memory, and fast interconnects, are an ideal candidate for the implementation of multimedia applications. Initially, multiprocessors were designed to execute scientific programs and thus their architecture was optimized to provide low message latency and efficiently support regular communication patterns. Hence, they have a regular network topology and most use wormhole routing. The design offers the benefits of a simple router, small buffer size, and network latency that is almost independent of path length. Among the various multimedia applications, video on demand (VOD) server is well-suited for implementation using parallel multiprocessors. Logical models for VOD servers are presently mapped onto multiprocessors. Our paper provides a framework for calculating bounds on utilization of system resources with which QoS parameters for each isochronous stream can be guaranteed. Effects of the architecture of multiprocessors, and efficiency of various local models and mapping on particular architectures can be investigated within our framework. Our framework is based on rigorous proofs and provides tight bounds. The results obtained may be used as the basis for admission control tests. To illustrate the versatility of our framework, we provide bounds on utilization for various logical models applied to mesh connected architectures for a video on demand server. Our results show that worm hole routing can lead to packets waiting for transmission of other packets that apparently share no common resources. This situation is analogous to head-of-the-line blocking. We find that the provision of multiple VCs per link and multiple flit buffers improves utilization (even under guaranteed QoS parameters). This analogous to parallel iterative matching.

Structure-based Mechanism of CMP-2-keto-3-deoxymanno-octulonic Acid Synthetase

PubMed Central

Heyes, Derren J.; Levy, Colin; Lafite, Pierre; Roberts, Ian S.; Goldrick, Marie; Stachulski, Andrew V.; Rossington, Steven B.; Stanford, Deborah; Rigby, Stephen E. J.; Scrutton, Nigel S.; Leys, David

2009-01-01

The enzyme CMP-Kdo synthetase (KdsB) catalyzes the addition of 2-keto-3-deoxymanno-octulonic acid (Kdo) to CTP to form CMP-Kdo, a key reaction in the biosynthesis of lipopolysaccharide. The reaction catalyzed by KdsB and the related CMP-acylneuraminate synthase is unique among the sugar-activating enzymes in that the respective sugars are directly coupled to a cytosine monophosphate. Using inhibition studies, in combination with isothermal calorimetry, we show the substrate analogue 2β-deoxy-Kdo to be a potent competitive inhibitor. The ligand-free Escherichia coli KdsB and ternary complex KdsB-CTP-2β-deoxy-Kdo crystal structures reveal that Kdo binding leads to active site closure and repositioning of the CTP phosphates and associated Mg2+ ion (Mg-B). Both ligands occupy conformations compatible with an Sn2-type attack on the α-phosphate by the Kdo 2-hydroxyl group. Based on strong similarity with DNA/RNA polymerases, both in terms of overall chemistry catalyzed as well as active site configuration, we postulate a second Mg2+ ion (Mg-A) is bound by the catalytically competent KdsB-CTP-Kdo ternary complex. Modeling of this complex reveals the Mg-A coordinated to the conserved Asp100 and Asp235 in addition to the CTP α-phosphate and both the Kdo carboxylic and 2-hydroxyl groups. EPR measurements on the Mn2+-substituted ternary complex support this model. We propose the KdsB/CNS sugar-activating enzymes catalyze the formation of activated sugars, such as the abundant CMP-5-N-acetylneuraminic acid, by recruitment of two Mg2+ to the active site. Although each metal ion assists in correct positioning of the substrates and activation of the α-phosphate, Mg-A is responsible for activation of the sugar-hydroxyl group. PMID:19815542

Estimating Temporal Redistribution of Surface Melt Water into Upper Stratigraphy of the Juneau Icefield, Alaska

NASA Astrophysics Data System (ADS)

Wilner, J.; Smith, B.; Moore, T.; Campbell, S. W.; Slavin, B. V.; Hollander, J.; Wolf, J.

2015-12-01

The redistribution of winter accumulation from surface melt into firn or deeper layers (i.e. internal accumulation) remains a poorly understood component of glacier mass balance. Winter accumulation is usually quantified prior to summer melt, however the time window between accumulation and the onset of melt is minimal so this is not always possible. Studies which are initiated following the onset of summer melt either neglect sources of internal accumulation or attempt to estimate melt (and therefore winter accumulation uncertainty) through a variety of modeling methods. Here, we used ground-penetrating radar (GPR) repeat common midpoint (CMP) surveys with supporting common offset surveys, mass balance snow pits, and probing to estimate temporal changes in water content within the winter accumulation and firn layers of the southern Juneau Icefield, Alaska. In temperate glaciers, radio-wave velocity is primarily dependent on water content and snow or firn density. We assume density changes are temporally slow relative to water flow through the snow and firn pack, and therefore infer that changing radio-wave velocities measured by successive CMP surveys result from flux in surface melt through deeper layers. Preliminary CMP data yield radio-wave velocities of 0.15 to 0.2 m/ns in snowpack densities averaging 0.56 g cm-3, indicating partially to fully saturated snowpack (4-9% water content). Further spatial-temporal analysis of CMP surveys is being conducted. We recommend that repeat CMP surveys be conducted over a longer time frame to estimate stratigraphic water redistribution between the end of winter accumulation and maximum melt season. This information could be incorporated into surface energy balance models to further understanding of the influence of internal accumulation on glacier mass balance.

Mineral materials as feasible amendments to stabilize heavy metals in polluted urban soils.

PubMed

Zhang, Mingkui; Pu, Jincheng

2011-01-01

Four minerals, agricultural limestone (AL), rock phosphate (RP), palygorskite (PG), and calcium magnesium phosphate (CMP), were evaluated by means of chemical fractions of heavy metals in soils and concentrations of heavy metals in leachates from columns to determine their ability to stabilize heavy metals in polluted urban soils. Two urban soils (calcareous soil and acidic soil) polluted with cadmium, copper, zinc and lead were selected and amended in the laboratory with the mineral materials) for 12 months. Results indicated that application of the mineral materials reduced exchangeable metals in the sequence of Pb, Cd > Cu > Zn. The reduction of exchangeable fraction of heavy metals in the soils amended with different mineral materials followed the sequence of CMP, PG > AL > RP. Reductions of heavy metals leached were based on comparison with cumulative totals of heavy metals eluted through 12 pore volumes from an untreated soil. The reductions of the metals eluted from the calcareous soil amended with the RP, AL, PG and CMP were 1.98%, 38.89%, 64.81% and 75.93% for Cd, 8.51%, 40.42%, 60.64% and 55.32% for Cu, 1.76%, 52.94%, 70.00% and 74.12% for Pb, and 28.42%, 52.74%, 64.38% and 49.66% for Zn. Those from the acidic soil amended with the CMP, PG, AL, and RP were 25.65%, 68.06%, 78.01% and 79.06% for Cd, 26.56%, 49.64%, 43.40% and 34.68% for Cu, 44.44%, 33.32%, 61.11% and 69.44% for Pb, and 18.46%, 43.77%, 41.98% and 40.68% for Zn. The CMP and PG treatments were superior to the AL and RP for stabilizing heavy metals in the polluted urban soils.

The Community Mentorship Program: Providing Community-Engagement Opportunities for Early-Stage Clinical and Translational Scientists to Facilitate Research Translation

PubMed Central

Patino, Cecilia M.; Kubicek, Katrina; Robles, Marisela; Kiger, Holly; Dzekov, Jeanne

2016-01-01

Problem A goal of the Southern California Clinical and Translational Science Institute (SC-CTSI) at the University of Southern California (USC) and Children's Hospital Los Angeles is to train early-stage clinical translational scientists (CTSs) to conduct research that improves the health of diverse communities. This goal aligns well with the Institute of Medicine's recommendations emphasizing community engagement in biomedical research that facilitates research translation. The Community Mentorship Program (CMP), created to complement community-engaged research (CER) didactics, matches CTSs with community mentors who help CTSs identify and complete community-engaged experiences that inform their research. Approach The CMP was piloted in 2013-2015 by the SC-CTSI Workforce Development and Community-Engagement cores. The CMP team matched three CTSs (assistant professors pursuing mentored career development awards, two with CER experience) with mentors at community-based organizations (CBOs) aligned with their research interests. Each mentor–mentee pair signed a memorandum of understanding. The CMP team checked in regularly, monitoring progress and addressing challenges in CTSs’ completion of their community-engaged experience. Outcomes All pairs completed at least one community-engaged activity informing the CTS's research. In exit interviews, the CTSs and CBO mentors expressed satisfaction with the program and stated they would continue to work together. The CTSs reported the program provided opportunities to develop networks outside academia, build trust within the community, and receive feedback and learn from individuals in communities affected by their research. Next Steps The CMP will be expanded to include all eligible early-career CTSs and promoted for use in similar settings outside the SC-CTSI. PMID:27508342

Oral delivery of Brucella spp. recombinant protein U-Omp16 abrogates the IgE-mediated milk allergy.

PubMed

Smaldini, Paola Lorena; Ibañez, Andrés Esteban; Fossati, Carlos Alberto; Cassataro, Juliana; Docena, Guillermo Horacio

2014-01-01

Food allergies are increasingly common disorders and no therapeutic strategies are yet approved. The unlipidated Omp16 (U-Omp16) is the outer membrane protein of 16 kDa from B. abortus and possesses a mucosal adjuvant property. In this study, we aimed to examine the U-Omp16 capacity to abrogate an allergen-specific Th2 immune response when it is administered as an oral adjuvant in a mouse model of food allergy.   Balb/c mice were sensitized with cholera toxin and cow's milk proteins (CMP) by gavage and simultaneously treated with U-Omp16 and CMP. Oral challenge with CMP was performed to evaluate the allergic status of mice. Symptoms, local (small bowel cytokine and transcription factor gene expression) and systemic (specific isotypes and spleen cell-secreted cytokines) parameters, and skin tests were done to evaluate the immune response. We found that the oral administration of U-Omp16 with CMP during sensitization dampened the allergic symptoms, with negativization of immediate skin test and increased skin DTH response. Serum specific IgE and IL-5 were inhibited and a Th1 response was promoted (specific IgG2a antibodies and CMP-induced IFN-γ secretion). We found at the mucosal site an inhibition of the gene expression corresponding to IL-13 and Gata-3, with an induction of IFN-γ and T-bet. These results indicated that the oral administration of U-Omp16 significantly controlled the allergic response in sensitized mice with a shift of the balance of Th1- and Th2-T cells toward Th1 predominance. These findings suggest that U-Omp16 may be useful as a Th1-directing adjuvant in an oral vaccine.

Oral delivery of Brucella spp. recombinant protein U-Omp16 abrogates the IgE-mediated milk allergy

PubMed Central

Smaldini, Paola Lorena; Ibañez, Andrés Esteban; Fossati, Carlos Alberto; Cassataro, Juliana; Docena, Guillermo Horacio

2014-01-01

Food allergies are increasingly common disorders and no therapeutic strategies are yet approved. The unlipidated Omp16 (U-Omp16) is the outer membrane protein of 16 kDa from B. abortus and possesses a mucosal adjuvant property. In this study, we aimed to examine the U-Omp16 capacity to abrogate an allergen-specific Th2 immune response when it is administered as an oral adjuvant in a mouse model of food allergy.   Balb/c mice were sensitized with cholera toxin and cow’s milk proteins (CMP) by gavage and simultaneously treated with U-Omp16 and CMP. Oral challenge with CMP was performed to evaluate the allergic status of mice. Symptoms, local (small bowel cytokine and transcription factor gene expression) and systemic (specific isotypes and spleen cell-secreted cytokines) parameters, and skin tests were done to evaluate the immune response. We found that the oral administration of U-Omp16 with CMP during sensitization dampened the allergic symptoms, with negativization of immediate skin test and increased skin DTH response. Serum specific IgE and IL-5 were inhibited and a Th1 response was promoted (specific IgG2a antibodies and CMP-induced IFN-γ secretion). We found at the mucosal site an inhibition of the gene expression corresponding to IL-13 and Gata-3, with an induction of IFN-γ and T-bet. These results indicated that the oral administration of U-Omp16 significantly controlled the allergic response in sensitized mice with a shift of the balance of Th1- and Th2-T cells toward Th1 predominance. These findings suggest that U-Omp16 may be useful as a Th1-directing adjuvant in an oral vaccine. PMID:25424811

Effects of age on the soccer-specific cognitive-motor performance of elite young soccer players: Comparison between objective measurements and coaches’ evaluation

PubMed Central

Chauvin, Alan; Chassot, Steve; Chenevière, Xavier; Taube, Wolfgang

2017-01-01

The cognitive-motor performance (CMP), defined here as the capacity to rapidly use sensory information and transfer it into efficient motor output, represents a major contributor to performance in almost all sports, including soccer. Here, we used a high-technology system (COGNIFOOT) which combines a visual environment simulator fully synchronized with a motion capture system. This system allowed us to measure objective real-time CMP parameters (passing accuracy/speed and response times) in a large turf-artificial grass playfield. Forty-six (46) young elite soccer players (including 2 female players) aged between 11 and 16 years who belonged to the same youth soccer academy were tested. Each player had to pass the ball as fast and as accurately as possible towards visual targets projected onto a large screen located 5.32 meters in front of him (a short pass situation). We observed a linear age-related increase in the CMP: the passing accuracy, speed and reactiveness of players improved by 4 centimeters, 2.3 km/h and 30 milliseconds per year of age, respectively. These data were converted into 5 point-scales and compared to the judgement of expert coaches, who also used a 5 point-scale to evaluate the same CMP parameters but based on their experience with the players during games and training. The objectively-measured age-related CMP changes were also observed in expert coaches’ judgments although these were more variable across coaches and age categories. This demonstrates that high-technology systems like COGNIFOOT can be used in complement to traditional approaches of talent identification and to objectively monitor the progress of soccer players throughout a cognitive-motor training cycle. PMID:28953958

Effects of age on the soccer-specific cognitive-motor performance of elite young soccer players: Comparison between objective measurements and coaches' evaluation.

PubMed

Hicheur, Halim; Chauvin, Alan; Chassot, Steve; Chenevière, Xavier; Taube, Wolfgang

2017-01-01

The cognitive-motor performance (CMP), defined here as the capacity to rapidly use sensory information and transfer it into efficient motor output, represents a major contributor to performance in almost all sports, including soccer. Here, we used a high-technology system (COGNIFOOT) which combines a visual environment simulator fully synchronized with a motion capture system. This system allowed us to measure objective real-time CMP parameters (passing accuracy/speed and response times) in a large turf-artificial grass playfield. Forty-six (46) young elite soccer players (including 2 female players) aged between 11 and 16 years who belonged to the same youth soccer academy were tested. Each player had to pass the ball as fast and as accurately as possible towards visual targets projected onto a large screen located 5.32 meters in front of him (a short pass situation). We observed a linear age-related increase in the CMP: the passing accuracy, speed and reactiveness of players improved by 4 centimeters, 2.3 km/h and 30 milliseconds per year of age, respectively. These data were converted into 5 point-scales and compared to the judgement of expert coaches, who also used a 5 point-scale to evaluate the same CMP parameters but based on their experience with the players during games and training. The objectively-measured age-related CMP changes were also observed in expert coaches' judgments although these were more variable across coaches and age categories. This demonstrates that high-technology systems like COGNIFOOT can be used in complement to traditional approaches of talent identification and to objectively monitor the progress of soccer players throughout a cognitive-motor training cycle.

Decision Support Preferences Among Hispanic and Non-Hispanic White Older Adults With Chronic Musculoskeletal Pain.

PubMed

Riffin, Catherine; Pillemer, Karl; Reid, Manny C; Lӧckenhoff, Corinna E

2016-09-01

Despite broad recognition that social networks play a key role in the management of chronic musculoskeletal pain (CMP), little is known about when and why older adults with CMP choose to involve others in treatment decisions. This study investigates the types (i.e., informational, emotional, and instrumental) and sources (i.e., formal and informal) of support Hispanic and non-Hispanic White CMP patients desire and receive when making decisions about their pain care. Semi-structured interviews were conducted with Hispanic and non-Hispanic White older adults with CMP (N = 63) recruited from one medical center and one senior center in New York City. Interviews were transcribed and then analyzed using content analysis. CMP patients sought network members who supported their emotional well-being throughout the decision-making process. When considering high-stakes treatment decisions, participants selectively involved individuals who had similar pain conditions or first-hand experience with the procedure. Participants' perceptions of the decision-making process were contingent upon the congruence between the decision they made and the support they received for it. For Spanish-speaking participants, positive perceptions were linked with satisfactory language competence by their providers. On the other hand, lack of language competence among providers hindered Spanish speakers' ability to obtain adequate informational support. Results reveal the importance of empathic patient-provider exchanges across diverse patient populations and cultural sensitivity for Spanish-speaking patients. Findings suggest that social networks beyond the patient-provider dyad influence patients' decision-making satisfaction. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Parallelising a molecular dynamics algorithm on a multi-processor workstation

NASA Astrophysics Data System (ADS)

Müller-Plathe, Florian

1990-12-01

The Verlet neighbour-list algorithm is parallelised for a multi-processor Hewlett-Packard/Apollo DN10000 workstation. The implementation makes use of memory shared between the processors. It is a genuine master-slave approach by which most of the computational tasks are kept in the master process and the slaves are only called to do part of the nonbonded forces calculation. The implementation features elements of both fine-grain and coarse-grain parallelism. Apart from three calls to library routines, two of which are standard UNIX calls, and two machine-specific language extensions, the whole code is written in standard Fortran 77. Hence, it may be expected that this parallelisation concept can be transfered in parts or as a whole to other multi-processor shared-memory computers. The parallel code is routinely used in production work.

Satisfiability Test with Synchronous Simulated Annealing on the Fujitsu AP1000 Massively-Parallel Multiprocessor

NASA Technical Reports Server (NTRS)

Sohn, Andrew; Biswas, Rupak

1996-01-01

Solving the hard Satisfiability Problem is time consuming even for modest-sized problem instances. Solving the Random L-SAT Problem is especially difficult due to the ratio of clauses to variables. This report presents a parallel synchronous simulated annealing method for solving the Random L-SAT Problem on a large-scale distributed-memory multiprocessor. In particular, we use a parallel synchronous simulated annealing procedure, called Generalized Speculative Computation, which guarantees the same decision sequence as sequential simulated annealing. To demonstrate the performance of the parallel method, we have selected problem instances varying in size from 100-variables/425-clauses to 5000-variables/21,250-clauses. Experimental results on the AP1000 multiprocessor indicate that our approach can satisfy 99.9 percent of the clauses while giving almost a 70-fold speedup on 500 processors.

A flexible nanobrush pad for the chemical mechanical planarization of Cu/ultra-low-к materials

NASA Astrophysics Data System (ADS)

Han, Guiquan; Liu, Yuhong; Lu, Xinchun; Luo, Jianbin

2012-10-01

A new idea of polishing pad called flexible nanobrush pad (FNP) has been proposed for the low down pressure chemical mechanical planarization (CMP) process of Cu/ultra-low-к materials. The FNP was designed with a surface layer of flexible brush-like nanofibers which can `actively' carry nanoscale abrasives in slurry independent of the down pressure. Better planarization performances including high material removal rate, good planarization, good polishing uniformity, and low defectivity are expected in the CMP process under the low down pressure with such kind of pad. The FNP can be made by template-assisted replication or template-based synthesis methods, which will be driven by the development of the preparation technologies for ordered nanostructure arrays. The present work would potentially provide a new solution for the Cu/ultra-low-к CMP process.

Defectivity control of aluminum chemical mechanical planarization in replacement metal gate process of MOSFET

NASA Astrophysics Data System (ADS)

Jin, Zhang; Yuling, Liu; Chenqi, Yan; Yangang, He; Baohong, Gao

2016-04-01

The replacement metal gate (RMG) defectivity performance control is very challenging in high-k metal gate (HKMG) chemical mechanical polishing (CMP). In this study, three major defect types, including fall-on particles, micro-scratch and corrosion have been investigated. The research studied the effects of polishing pad, pressure, rotating speed, flow rate and post-CMP cleaning on the three kinds of defect, which finally eliminated the defects and achieved good surface morphology. This study will provide an important reference value for the future research of aluminum metal gate CMP. Project supported by the Major National Science and Technology Special Projects (No. 2009ZX02308), the Natural Science Foundation for the Youth of Hebei Province (Nos. F2012202094, F2015202267), and the Outstanding Youth Science and Technology Innovation Fund of Hebei University of Technology (No. 2013010).

Scheduling for Locality in Shared-Memory Multiprocessors

DTIC Science & Technology

1993-05-01

Submitted in Partial Fulfillment of the Requirements for the Degree ’)iIC Q(JALfryT INSPECTED 5 DOCTOR OF PHILOSOPHY I Accesion For Supervised by NTIS CRAM... architecture on parallel program performance, explain the implications of this trend on popular parallel programming models, and propose system software to 0...decomoosition and scheduling algorithms. I. SUIUECT TERMS IS. NUMBER OF PAGES shared-memory multiprocessors; architecture trends; loop 110 scheduling

The MIT Alewife Machine: A Large-Scale Distributed-Memory Multiprocessor

DTIC Science & Technology

1991-06-01

Symposium on Compiler Construction, June 1986. [14] Daniel Gajski , David Kuck, Duncan Lawrie, and Ahmed Saleh. Cedar - A Large Scale Multiprocessor. In...Directory Methods. In Proceedings 17th Annual International Symposium on Computer Architecture, June 1990. [31] G . M. Papadopoulos and D.E. Culler...Monsoon: An Explicit Token-Store Ar- chitecture. In Proceedings 17th Annual International Symposium on Computer Architecture, June 1990. [32] G . F

Adaptive Backoff Synchronization Techniques

DTIC Science & Technology

1989-06-01

The Simple Code. Technical Report, Lawrence Livermore Laboratory, February 1978. [6J F. Darems-Rogers, D. A. George, V. A. Norton, and G . F. Pfister...Heights, November 1986. 20 [7] Daniel Gajski , David Kuck, Duncan Lawrie, and Ahmed Saleh. Cedar - A Large Scale Multiprocessor. In International Conference...17] Janak H. Patel. Analysis of Multiprocessors with Private Cache Memories. IEEE Transactions on Com- puters, C-31(4):296-304, April 1982. [18] G

Operating system for a real-time multiprocessor propulsion system simulator

NASA Technical Reports Server (NTRS)

Cole, G. L.

1984-01-01

The success of the Real Time Multiprocessor Operating System (RTMPOS) in the development and evaluation of experimental hardware and software systems for real time interactive simulation of air breathing propulsion systems was evaluated. The Real Time Multiprocessor Operating System (RTMPOS) provides the user with a versatile, interactive means for loading, running, debugging and obtaining results from a multiprocessor based simulator. A front end processor (FEP) serves as the simulator controller and interface between the user and the simulator. These functions are facilitated by the RTMPOS which resides on the FEP. The RTMPOS acts in conjunction with the FEP's manufacturer supplied disk operating system that provides typical utilities like an assembler, linkage editor, text editor, file handling services, etc. Once a simulation is formulated, the RTMPOS provides for engineering level, run time operations such as loading, modifying and specifying computation flow of programs, simulator mode control, data handling and run time monitoring. Run time monitoring is a powerful feature of RTMPOS that allows the user to record all actions taken during a simulation session and to receive advisories from the simulator via the FEP. The RTMPOS is programmed mainly in PASCAL along with some assembly language routines. The RTMPOS software is easily modified to be applicable to hardware from different manufacturers.

Effects of the Connected Mathematics Project 2 (CMP2) on the Mathematics Achievement of Grade 6 Students in the Mid-Atlantic Region. Final Report. NCEE 2012-4017

ERIC Educational Resources Information Center

Martin, Taylor; Brasiel, Sarah J.; Turner, Herb; Wise, John C.

2012-01-01

This study examines the effects of Connected Mathematics Project 2 (CMP2) on grade 6 student mathematics achievement and engagement using a cluster randomized controlled trial (RCT) design. It responds to a need to improve mathematics learning in the Mid-Atlantic Region (Delaware, Maryland, New Jersey, Pennsylvania, and Washington, DC). Findings…

Student Attainment in Connected Mathematics Curriculum [and] Effects of the Connected Mathematics Project on Student Achievement. What Works Clearinghouse Detailed Study Report

ERIC Educational Resources Information Center

What Works Clearinghouse, 2004

2004-01-01

In this study, Ridgway et al. found mixed results, depending on the assessment test used. With the Balanced Assessment (BA) test, positive significant differences were found between the Connected Mathematics Project (CMP) students and non-CMP students in grades 6, 7, and 8. The results for the Iowa Test of Basic Skills (ITBS) were less favorable…

Student Attainment in Connected Mathematics Curriculum [and] Effects of the Connected Mathematics Project on Student Achievement. What Works Clearinghouse Brief Study Report

ERIC Educational Resources Information Center

What Works Clearinghouse, 2004

2004-01-01

In this study, Ridgway et al. found mixed results, depending on the assessment test used. With the Balanced Assessment (BA) test, positive significant differences were found between the Connected Mathematics Project (CMP) students and non-CMP students in grades 6, 7, and 8. The results for the Iowa Test of Basic Skills (ITBS) were less favorable…

Free-free and fixed base modal survey tests of the Space Station Common Module Prototype

NASA Technical Reports Server (NTRS)

Driskill, T. C.; Anderson, J. B.; Coleman, A. D.

1992-01-01

This paper describes the testing aspects and the problems encountered during the free-free and fixed base modal surveys completed on the original Space Station Common Module Prototype (CMP). The CMP is a 40-ft long by 14.5-ft diameter 'waffle-grid' cylinder built by the Boeing Company and housed at the Marshall Space Flight Center (MSFC) near Huntsville, AL. The CMP modal survey tests were conducted at MSFC by the Dynamics Test Branch. The free-free modal survey tests (June '90 to Sept. '90) included interface verification tests (IFVT), often referred to as impedance measurements, mass-additive testing and linearity studies. The fixed base modal survey tests (Feb. '91 to April '91), including linearity studies, were conducted in a fixture designed to constrain the CMP in 7 total degrees-of-freedom at five trunnion interfaces (two primary, two secondary, and the keel). The fixture also incorporated an airbag off-load system designed to alleviate the non-linear effects of friction in the primary and secondary trunnion interfaces. Numerous test configurations were performed with the objective of providing a modal data base for evaluating the various testing methodologies to verify dynamic finite element models used for input to coupled load analysis.

Intellectual disability and bleeding diathesis due to deficient CMP--sialic acid transport.

PubMed

Mohamed, Miski; Ashikov, Angel; Guillard, Mailys; Robben, Joris H; Schmidt, Samuel; van den Heuvel, B; de Brouwer, Arjan P M; Gerardy-Schahn, Rita; Deen, Peter M T; Wevers, Ron A; Lefeber, Dirk J; Morava, Eva

2013-08-13

To identify the underlying genetic defect in a patient with intellectual disability, seizures, ataxia, macrothrombocytopenia, renal and cardiac involvement, and abnormal protein glycosylation. Genetic studies involved homozygosity mapping by 250K single nucleotide polymorphism array and SLC35A1 sequencing. Functional studies included biochemical assays for N-glycosylation and mucin-type O-glycosylation and SLC35A1-encoded cytidine 5'-monophosphosialic acid (CMP-sialic acid) transport after heterologous expression in yeast. We performed biochemical analysis and found combined N- and O-glycosylation abnormalities and specific reduction in sialylation in this patient. Homozygosity mapping revealed homozygosity for the CMP-sialic acid transporter SLC35A1. Mutation analysis identified a homozygous c.303G > C (p.Gln101His) missense mutation that was heterozygous in both parents. Functional analysis of mutant SLC35A1 showed normal Golgi localization but 50% reduction in transport activity of CMP-sialic acid in vitro. We confirm an autosomal recessive, generalized sialylation defect due to mutations in SLC35A1. The primary neurologic presentation consisting of ataxia, intellectual disability, and seizures, in combination with bleeding diathesis and proteinuria, is discriminative from a previous case described with deficient sialic acid transporter. Our study underlines the importance of sialylation for normal CNS development and regular organ function.

Development and application of a crossbreeding simulation model for goat production systems in tropical regions.

PubMed

Tsukahara, Y; Oishi, K; Hirooka, H

2011-12-01

A deterministic simulation model was developed to estimate biological production efficiency and to evaluate goat crossbreeding systems under tropical conditions. The model involves 5 production systems: pure indigenous, first filial generations (F1), backcross (BC), composite breeds of F1 (CMP(F1)), and BC (CMP(BC)). The model first simulates growth, reproduction, lactation, and energy intakes of a doe and a kid on a 1-d time step at the individual level and thereafter the outputs are integrated into the herd dynamics program. The ability of the model to simulate individual performances was tested under a base situation. The simulation results represented daily BW changes, ME requirements, and milk yield and the estimates were within the range of published data. Two conventional goat production scenarios (an intensive milk production scenario and an integrated goat and oil palm production scenario) in Malaysia were examined. The simulation results of the intensive milk production scenario showed the greater production efficiency of the CMP(BC) and CMP(F1) systems and decreased production efficiency of the F1 and BC systems. The results of the integrated goat and oil palm production scenario showed that the production efficiency and stocking rate were greater for the indigenous goats than for the crossbreeding systems.

The FORCE - A highly portable parallel programming language

NASA Technical Reports Server (NTRS)

Jordan, Harry F.; Benten, Muhammad S.; Alaghband, Gita; Jakob, Ruediger

1989-01-01

This paper explains why the FORCE parallel programming language is easily portable among six different shared-memory multiprocessors, and how a two-level macro preprocessor makes it possible to hide low-level machine dependencies and to build machine-independent high-level constructs on top of them. These FORCE constructs make it possible to write portable parallel programs largely independent of the number of processes and the specific shared-memory multiprocessor executing them.

Reducing Response Time Bounds for DAG-Based Task Systems on Heterogeneous Multicore Platforms

DTIC Science & Technology

2016-01-01

synchronous parallel tasks on multicore platforms. In 25th ECRTS, 2013. [10] U. Devi. Soft Real - Time Scheduling on Multiprocessors. PhD thesis...report, Washington University in St Louis, 2014. [18] C. Liu and J. Anderson. Supporting soft real - time DAG-based sys- tems on multiprocessors with...analysis for DAG-based real - time task systems im- plemented on heterogeneous multicore platforms. The spe- cific analysis problem that is considered was

Graphics applications utilizing parallel processing

NASA Technical Reports Server (NTRS)

Rice, John R.

1990-01-01

The results are presented of research conducted to develop a parallel graphic application algorithm to depict the numerical solution of the 1-D wave equation, the vibrating string. The research was conducted on a Flexible Flex/32 multiprocessor and a Sequent Balance 21000 multiprocessor. The wave equation is implemented using the finite difference method. The synchronization issues that arose from the parallel implementation and the strategies used to alleviate the effects of the synchronization overhead are discussed.

Dynamic file-access characteristics of a production parallel scientific workload

NASA Technical Reports Server (NTRS)

Kotz, David; Nieuwejaar, Nils

1994-01-01

Multiprocessors have permitted astounding increases in computational performance, but many cannot meet the intense I/O requirements of some scientific applications. An important component of any solution to this I/O bottleneck is a parallel file system that can provide high-bandwidth access to tremendous amounts of data in parallel to hundreds or thousands of processors. Most successful systems are based on a solid understanding of the expected workload, but thus far there have been no comprehensive workload characterizations of multiprocessor file systems. This paper presents the results of a three week tracing study in which all file-related activity on a massively parallel computer was recorded. Our instrumentation differs from previous efforts in that it collects information about every I/O request and about the mix of jobs running in a production environment. We also present the results of a trace-driven caching simulation and recommendations for designers of multiprocessor file systems.

Safe and Efficient Support for Embeded Multi-Processors in ADA

NASA Astrophysics Data System (ADS)

Ruiz, Jose F.

2010-08-01

New software demands increasing processing power, and multi-processor platforms are spreading as the answer to achieve the required performance. Embedded real-time systems are also subject to this trend, but in the case of real-time mission-critical systems, the properties of reliability, predictability and analyzability are also paramount. The Ada 2005 language defined a subset of its tasking model, the Ravenscar profile, that provides the basis for the implementation of deterministic and time analyzable applications on top of a streamlined run-time system. This Ravenscar tasking profile, originally designed for single processors, has proven remarkably useful for modelling verifiable real-time single-processor systems. This paper proposes a simple extension to the Ravenscar profile to support multi-processor systems using a fully partitioned approach. The implementation of this scheme is simple, and it can be used to develop applications amenable to schedulability analysis.

A Multiprocessor Operating System Simulator

NASA Technical Reports Server (NTRS)

Johnston, Gary M.; Campbell, Roy H.

1988-01-01

This paper describes a multiprocessor operating system simulator that was developed by the authors in the Fall semester of 1987. The simulator was built in response to the need to provide students with an environment in which to build and test operating system concepts as part of the coursework of a third-year undergraduate operating systems course. Written in C++, the simulator uses the co-routine style task package that is distributed with the AT&T C++ Translator to provide a hierarchy of classes that represents a broad range of operating system software and hardware components. The class hierarchy closely follows that of the 'Choices' family of operating systems for loosely- and tightly-coupled multiprocessors. During an operating system course, these classes are refined and specialized by students in homework assignments to facilitate experimentation with different aspects of operating system design and policy decisions. The current implementation runs on the IBM RT PC under 4.3bsd UNIX.

Reciprocal Interactions between Multiple Myeloma Cells and Osteoprogenitor Cells Affect Bone Formation and Tumor Growth

DTIC Science & Technology

2015-12-01

cells (HSCs) are multipotent cells that differentiate into myeloid, lymphoid and erythroid lineages, and have short-term or long-term regenerative...All rights reserved Nature Reviews | Rheumatology a b MPP CMP CLP Lymphoid cells NK cellB cell T cell Megakaryocyte and erythrocytes Macrophage and...into other cell types. CLP, common lymphoid progenitor; CMP, common myeloid progenitor; MPP, multipotent progenitor; NK cell , natural killer cell . R E

A flexible nanobrush pad for the chemical mechanical planarization of Cu/ultra-low-к materials

PubMed Central

2012-01-01

A new idea of polishing pad called flexible nanobrush pad (FNP) has been proposed for the low down pressure chemical mechanical planarization (CMP) process of Cu/ultra-low-к materials. The FNP was designed with a surface layer of flexible brush-like nanofibers which can ‘actively’ carry nanoscale abrasives in slurry independent of the down pressure. Better planarization performances including high material removal rate, good planarization, good polishing uniformity, and low defectivity are expected in the CMP process under the low down pressure with such kind of pad. The FNP can be made by template-assisted replication or template-based synthesis methods, which will be driven by the development of the preparation technologies for ordered nanostructure arrays. The present work would potentially provide a new solution for the Cu/ultra-low-к CMP process. PMID:23110959

[The optimization of chondromalacia patellae diagnosis by NMR tomography. The use of an apparatus for cartilage compression].

PubMed

König, H; Dinkelaker, F; Wolf, K J

1991-08-01

The aim of this study was to improve the MRI diagnosis of CMP, with special reference to the early stages and accurate staging. For this purpose, the retropatellar cartilage was examined by MRI while compression was carried out, using 21 patients and five normal controls. The compression was applied by means of a specially constructed device. Changes in cartilage thickness and signal intensity were evaluated quantitatively during FLASH and FISP sequences. In all patients the results of arthroscopies were available and in 12 patients, cartilage biopsies had been obtained. CMP stage I could be distinguished from normal cartilage by reduction in cartilage thickness and signal increase from the oedematous cartilage during compression. In CMP stages II/III, abnormal protein deposition of collagen type I could be demonstrated by its compressibility. In stages III and IV, the method does not add any significant additional information.

Acupuncture and chiropractic care for chronic pain in an integrated health plan: a mixed methods study

PubMed Central

2011-01-01

Background Substantial recent research examines the efficacy of many types of complementary and alternative (CAM) therapies. However, outcomes associated with the "real-world" use of CAM has been largely overlooked, despite calls for CAM therapies to be studied in the manner in which they are practiced. Americans seek CAM treatments far more often for chronic musculoskeletal pain (CMP) than for any other condition. Among CAM treatments for CMP, acupuncture and chiropractic (A/C) care are among those with the highest acceptance by physician groups and the best evidence to support their use. Further, recent alarming increases in delivery of opioid treatment and surgical interventions for chronic pain--despite their high costs, potential adverse effects, and modest efficacy--suggests the need to evaluate real world outcomes associated with promising non-pharmacological/non-surgical CAM treatments for CMP, which are often well accepted by patients and increasingly used in the community. Methods/Design This multi-phase, mixed methods study will: (1) conduct a retrospective study using information from electronic medical records (EMRs) of a large HMO to identify unique clusters of patients with CMP (e.g., those with differing demographics, histories of pain condition, use of allopathic and CAM health services, and comorbidity profiles) that may be associated with different propensities for A/C utilization and/or differential outcomes associated with such care; (2) use qualitative interviews to explore allopathic providers' recommendations for A/C and patients' decisions to pursue and retain CAM care; and (3) prospectively evaluate health services/costs and broader clinical and functional outcomes associated with the receipt of A/C relative to carefully matched comparison participants receiving traditional CMP services. Sensitivity analyses will compare methods relying solely on EMR-derived data versus analyses supplementing EMR data with conventionally collected patient and clinician data. Discussion Successful completion of these aggregate aims will provide an evaluation of outcomes associated with the real-world use of A/C services. The trio of retrospective, qualitative, and prospective study will also provide a clearer understanding of the decision-making processes behind the use of A/C for CMP and a transportable methodology that can be applied to other health care settings, CAM treatments, and clinical populations. Trial registration ClinicalTrials.gov: NCT01345409 PMID:22118061

Cache as point of coherence in multiprocessor system

DOEpatents

Blumrich, Matthias A.; Ceze, Luis H.; Chen, Dong; Gara, Alan; Heidelberger, Phlip; Ohmacht, Martin; Steinmacher-Burow, Burkhard; Zhuang, Xiaotong

2016-11-29

In a multiprocessor system, a conflict checking mechanism is implemented in the L2 cache memory. Different versions of speculative writes are maintained in different ways of the cache. A record of speculative writes is maintained in the cache directory. Conflict checking occurs as part of directory lookup. Speculative versions that do not conflict are aggregated into an aggregated version in a different way of the cache. Speculative memory access requests do not go to main memory.

Multiprocessor Real-Time Locking Protocols for Replicated Resources

DTIC Science & Technology

2016-07-01

circular buffer of slots, each representing a discrete segment of time . For example, if the maintenance of a timing wheel occurs af- ter an interrupt ...Experimental Evaluation To evaluate Algs. 2, 3, and 4, we conducted a series of ex- periments in which we measured relevant overheads and blocking times . We...Multiprocessor Real- Time Locking Protocols for Replicated Resources ∗ Catherine E. Jarrett1, Kecheng Yang1, Ming Yang1, Pontus Ekberg2, and James H

Cedar-a large scale multiprocessor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gajski, D.; Kuck, D.; Lawrie, D.

1983-01-01

This paper presents an overview of Cedar, a large scale multiprocessor being designed at the University of Illinois. This machine is designed to accommodate several thousand high performance processors which are capable of working together on a single job, or they can be partitioned into groups of processors where each group of one or more processors can work on separate jobs. Various aspects of the machine are described including the control methodology, communication network, optimizing compiler and plans for construction. 13 references.

The force on the flex: Global parallelism and portability

NASA Technical Reports Server (NTRS)

Jordan, H. F.

1986-01-01

A parallel programming methodology, called the force, supports the construction of programs to be executed in parallel by an unspecified, but potentially large, number of processes. The methodology was originally developed on a pipelined, shared memory multiprocessor, the Denelcor HEP, and embodies the primitive operations of the force in a set of macros which expand into multiprocessor Fortran code. A small set of primitives is sufficient to write large parallel programs, and the system has been used to produce 10,000 line programs in computational fluid dynamics. The level of complexity of the force primitives is intermediate. It is high enough to mask detailed architectural differences between multiprocessors but low enough to give the user control over performance. The system is being ported to a medium scale multiprocessor, the Flex/32, which is a 20 processor system with a mixture of shared and local memory. Memory organization and the type of processor synchronization supported by the hardware on the two machines lead to some differences in efficient implementations of the force primitives, but the user interface remains the same. An initial implementation was done by retargeting the macros to Flexible Computer Corporation's ConCurrent C language. Subsequently, the macros were caused to directly produce the system calls which form the basis for ConCurrent C. The implementation of the Fortran based system is in step with Flexible Computer Corporations's implementation of a Fortran system in the parallel environment.

Impact of a human CMP-sialic acid transporter on recombinant glycoprotein sialylation in glycoengineered insect cells.

PubMed

Mabashi-Asazuma, Hideaki; Shi, Xianzong; Geisler, Christoph; Kuo, Chu-Wei; Khoo, Kay-Hooi; Jarvis, Donald L

2013-02-01

Insect cells are widely used for recombinant glycoprotein production, but they cannot provide the glycosylation patterns required for some biotechnological applications. This problem has been addressed by genetically engineering insect cells to express mammalian genes encoding various glycoprotein glycan processing functions. However, for various reasons, the impact of a mammalian cytosine-5'-monophospho (CMP)-sialic acid transporter has not yet been examined. Thus, we transformed Spodoptera frugiperda (Sf9) cells with six mammalian genes to generate a new cell line, SfSWT-4, that can produce sialylated glycoproteins when cultured with the sialic acid precursor, N-acetylmannosamine. We then super-transformed SfSWT-4 with a human CMP-sialic acid transporter (hCSAT) gene to isolate a daughter cell line, SfSWT-6, which expressed the hCSAT gene in addition to the other mammalian glycogenes. SfSWT-6 cells had higher levels of cell surface sialylation and also supported higher levels of recombinant glycoprotein sialylation, particularly when cultured with low concentrations of N-acetylmannosamine. Thus, hCSAT expression has an impact on glycoprotein sialylation, can reduce the cost of recombinant glycoprotein production and therefore should be included in ongoing efforts to glycoengineer the baculovirus-insect cell system. The results of this study also contributed new insights into the endogenous mechanism and potential mechanisms of CMP-sialic acid accumulation in the Golgi apparatus of lepidopteran insect cells.

A reliable control system for measurement on film thickness in copper chemical mechanical planarization system

NASA Astrophysics Data System (ADS)

Li, Hongkai; Qu, Zilian; Zhao, Qian; Tian, Fangxin; Zhao, Dewen; Meng, Yonggang; Lu, Xinchun

2013-12-01

In recent years, a variety of film thickness measurement techniques for copper chemical mechanical planarization (CMP) are subsequently proposed. In this paper, the eddy-current technique is used. In the control system of the CMP tool developed in the State Key Laboratory of Tribology, there are in situ module and off-line module for measurement subsystem. The in situ module can get the thickness of copper film on wafer surface in real time, and accurately judge when the CMP process should stop. This is called end-point detection. The off-line module is used for multi-points measurement after CMP process, in order to know the thickness of remained copper film. The whole control system is structured with two levels, and the physical connection between the upper and the lower is achieved by the industrial Ethernet. The process flow includes calibration and measurement, and there are different algorithms for two modules. In the process of software development, C++ is chosen as the programming language, in combination with Qt OpenSource to design two modules' GUI and OPC technology to implement the communication between the two levels. In addition, the drawing function is developed relying on Matlab, enriching the software functions of the off-line module. The result shows that the control system is running stably after repeated tests and practical operations for a long time.

A reliable control system for measurement on film thickness in copper chemical mechanical planarization system.

PubMed

Li, Hongkai; Qu, Zilian; Zhao, Qian; Tian, Fangxin; Zhao, Dewen; Meng, Yonggang; Lu, Xinchun

2013-12-01

In recent years, a variety of film thickness measurement techniques for copper chemical mechanical planarization (CMP) are subsequently proposed. In this paper, the eddy-current technique is used. In the control system of the CMP tool developed in the State Key Laboratory of Tribology, there are in situ module and off-line module for measurement subsystem. The in situ module can get the thickness of copper film on wafer surface in real time, and accurately judge when the CMP process should stop. This is called end-point detection. The off-line module is used for multi-points measurement after CMP process, in order to know the thickness of remained copper film. The whole control system is structured with two levels, and the physical connection between the upper and the lower is achieved by the industrial Ethernet. The process flow includes calibration and measurement, and there are different algorithms for two modules. In the process of software development, C++ is chosen as the programming language, in combination with Qt OpenSource to design two modules' GUI and OPC technology to implement the communication between the two levels. In addition, the drawing function is developed relying on Matlab, enriching the software functions of the off-line module. The result shows that the control system is running stably after repeated tests and practical operations for a long time.

A reliable control system for measurement on film thickness in copper chemical mechanical planarization system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hongkai; Qu, Zilian; Zhao, Qian

In recent years, a variety of film thickness measurement techniques for copper chemical mechanical planarization (CMP) are subsequently proposed. In this paper, the eddy-current technique is used. In the control system of the CMP tool developed in the State Key Laboratory of Tribology, there are in situ module and off-line module for measurement subsystem. The in situ module can get the thickness of copper film on wafer surface in real time, and accurately judge when the CMP process should stop. This is called end-point detection. The off-line module is used for multi-points measurement after CMP process, in order to knowmore » the thickness of remained copper film. The whole control system is structured with two levels, and the physical connection between the upper and the lower is achieved by the industrial Ethernet. The process flow includes calibration and measurement, and there are different algorithms for two modules. In the process of software development, C++ is chosen as the programming language, in combination with Qt OpenSource to design two modules’ GUI and OPC technology to implement the communication between the two levels. In addition, the drawing function is developed relying on Matlab, enriching the software functions of the off-line module. The result shows that the control system is running stably after repeated tests and practical operations for a long time.« less

Key Processes of Silicon-On-Glass MEMS Fabrication Technology for Gyroscope Application.

PubMed

Ma, Zhibo; Wang, Yinan; Shen, Qiang; Zhang, Han; Guo, Xuetao

2018-04-17

MEMS fabrication that is based on the silicon-on-glass (SOG) process requires many steps, including patterning, anodic bonding, deep reactive ion etching (DRIE), and chemical mechanical polishing (CMP). The effects of the process parameters of CMP and DRIE are investigated in this study. The process parameters of CMP, such as abrasive size, load pressure, and pH value of SF1 solution are examined to optimize the total thickness variation in the structure and the surface quality. The ratio of etching and passivation cycle time and the process pressure are also adjusted to achieve satisfactory performance during DRIE. The process is optimized to avoid neither the notching nor lag effects on the fabricated silicon structures. For demonstrating the capability of the modified CMP and DRIE processes, a z-axis micro gyroscope is fabricated that is based on the SOG process. Initial test results show that the average surface roughness of silicon is below 1.13 nm and the thickness of the silicon is measured to be 50 μm. All of the structures are well defined without the footing effect by the use of the modified DRIE process. The initial performance test results of the resonant frequency for the drive and sense modes are 4.048 and 4.076 kHz, respectively. The demands for this kind of SOG MEMS device can be fulfilled using the optimized process.

NeuA sialic acid O-acetylesterase activity modulates O-acetylation of capsular polysaccharide in group B Streptococcus.

PubMed

Lewis, Amanda L; Cao, Hongzhi; Patel, Silpa K; Diaz, Sandra; Ryan, Wesley; Carlin, Aaron F; Thon, Vireak; Lewis, Warren G; Varki, Ajit; Chen, Xi; Nizet, Victor

2007-09-21

Group B Streptococcus (GBS) is a common cause of neonatal sepsis and meningitis. A major GBS virulence determinant is its sialic acid (Sia)-capped capsular polysaccharide. Recently, we discovered the presence and genetic basis of capsular Sia O-acetylation in GBS. We now characterize a GBS Sia O-acetylesterase that modulates the degree of GBS surface O-acetylation. The GBS Sia O-acetylesterase operates cooperatively with the GBS CMP-Sia synthetase, both part of a single polypeptide encoded by the neuA gene. NeuA de-O-acetylation of free 9-O-acetyl-N-acetylneuraminic acid (Neu5,9Ac(2)) was enhanced by CTP and Mg(2+), the substrate and co-factor, respectively, of the N-terminal GBS CMP-Sia synthetase domain. In contrast, the homologous bifunctional NeuA esterase from Escherichia coli K1 did not display cofactor dependence. Further analyses showed that in vitro, GBS NeuA can operate via two alternate enzymatic pathways: de-O-acetylation of Neu5,9Ac(2) followed by CMP activation of Neu5Ac or activation of Neu5,9Ac(2) followed by de-O-acetylation of CMP-Neu5,9Ac(2). Consistent with in vitro esterase assays, genetic deletion of GBS neuA led to accumulation of intracellular O-acetylated Sias, and overexpression of GBS NeuA reduced O-acetylation of Sias on the bacterial surface. Site-directed mutagenesis of conserved asparagine residue 301 abolished esterase activity but preserved CMP-Sia synthetase activity, as evidenced by hyper-O-acetylation of capsular polysaccharide Sias on GBS expressing only the N301A NeuA allele. These studies demonstrate a novel mechanism regulating the extent of capsular Sia O-acetylation in intact bacteria and provide a genetic strategy for manipulating GBS O-acetylation in order to explore the role of this modification in GBS pathogenesis and immunogenicity.

Radical scavenger can scavenge lipid allyl radicals complexed with lipoxygenase at lower oxygen content.

PubMed

Koshiishi, Ichiro; Tsuchida, Kazunori; Takajo, Tokuko; Komatsu, Makiko

2006-04-15

Lipoxygenases have been proposed to be a possible factor that is responsible for the pathology of certain diseases, including ischaemic injury. In the peroxidation process of linoleic acid by lipoxygenase, the E,Z-linoleate allyl radical-lipoxygenase complex seems to be generated as an intermediate. In the present study, we evaluated whether E,Z-linoleate allyl radicals on the enzyme are scavenged by radical scavengers. Linoleic acid, the content of which was greater than the dissolved oxygen content, was treated with soya bean lipoxygenase-1 (ferric form) in the presence of radical scavenger, CmP (3-carbamoyl-2,2,5,5-tetramethylpyrrolidine-N-oxyl). The reaction rate between oxygen and lipid allyl radical is comparatively faster than that between CmP and lipid allyl radical. Therefore a reaction between linoleate allyl radical and CmP was not observed while the dioxygenation of linoleic acid was ongoing. After the dissolved oxygen was depleted, CmP stoichiometrically trapped linoleate-allyl radicals. Accompanied by this one-electron redox reaction, the resulting ferrous lipoxygenase was re-oxidized to the ferric form by hydroperoxylinoleate. Through the adduct assay via LC (liquid chromatography)-MS/MS (tandem MS), four E,Z-linoleate allyl radical-CmP adducts corresponding to regio- and diastereo-isomers were detected in the linoleate/lipoxygenase system, whereas E,E-linoleate allyl radical-CmP adducts were not detected at all. If E,Z-linoleate allyl radical is liberated from the enzyme, the E/Z-isomer has to reach equilibrium with the thermodynamically favoured E/E-isomer. These data suggested that the E,Z-linoleate allyl radicals were not liberated from the active site of lipoxygenase before being trapped by CmP. Consequently, we concluded that the lipid allyl radicals complexed with lipoxygenase could be scavenged by radical scavengers at lower oxygen content.

Radical scavenger can scavenge lipid allyl radicals complexed with lipoxygenase at lower oxygen content

PubMed Central

Koshiishi, Ichiro; Tsuchida, Kazunori; Takajo, Tokuko; Komatsu, Makiko

2006-01-01

Lipoxygenases have been proposed to be a possible factor that is responsible for the pathology of certain diseases, including ischaemic injury. In the peroxidation process of linoleic acid by lipoxygenase, the E,Z-linoleate allyl radical–lipoxygenase complex seems to be generated as an intermediate. In the present study, we evaluated whether E,Z-linoleate allyl radicals on the enzyme are scavenged by radical scavengers. Linoleic acid, the content of which was greater than the dissolved oxygen content, was treated with soya bean lipoxygenase-1 (ferric form) in the presence of radical scavenger, CmP (3-carbamoyl-2,2,5,5-tetramethylpyrrolidine-N-oxyl). The reaction rate between oxygen and lipid allyl radical is comparatively faster than that between CmP and lipid allyl radical. Therefore a reaction between linoleate allyl radical and CmP was not observed while the dioxygenation of linoleic acid was ongoing. After the dissolved oxygen was depleted, CmP stoichiometrically trapped linoleate-allyl radicals. Accompanied by this one-electron redox reaction, the resulting ferrous lipoxygenase was re-oxidized to the ferric form by hydroperoxylinoleate. Through the adduct assay via LC (liquid chromatography)–MS/MS (tandem MS), four E,Z-linoleate allyl radical–CmP adducts corresponding to regio- and diastereo-isomers were detected in the linoleate/lipoxygenase system, whereas E,E-linoleate allyl radical–CmP adducts were not detected at all. If E,Z-linoleate allyl radical is liberated from the enzyme, the E/Z-isomer has to reach equilibrium with the thermodynamically favoured E/E-isomer. These data suggested that the E,Z-linoleate allyl radicals were not liberated from the active site of lipoxygenase before being trapped by CmP. Consequently, we concluded that the lipid allyl radicals complexed with lipoxygenase could be scavenged by radical scavengers at lower oxygen content. PMID:16396633

Substrate-induced fit of the ATP binding site of cytidine monophosphate kinase from Escherichia coli: time-resolved fluorescence of 3'-anthraniloyl-2'-deoxy-ADP and molecular modeling.

PubMed

Li de La Sierra, I M; Gallay, J; Vincent, M; Bertrand, T; Briozzo, P; Bârzu, O; Gilles, A M

2000-12-26

The conformation and dynamics of the ATP binding site of cytidine monophosphate kinase from Escherichia coli (CMPK(coli)), which catalyzes specifically the phosphate exchange between ATP and CMP, was studied using the fluorescence properties of 3'-anthraniloyl-2'-deoxy-ADP, a specific ligand of the enzyme. The spectroscopic properties of the bound fluorescent nucleotide change strongly with respect to those in aqueous solution. These changes (red shift of the absorption and excitation spectra, large increase of the excited state lifetime) are compared to those observed in different solvents. These data, as well as acrylamide quenching experiments, suggest that the anthraniloyl moiety is protected from the aqueous solvent upon binding to the ATP binding site, irrespective of the presence of CMP or CDP. The protein-bound ADP analogue exhibits a restricted fast subnanosecond rotational motion, completely blocked by CMP binding. The energy-minimized models of CMPK(coli) complexed with 3'-anthraniloyl-2'-deoxy-ADP using the crystal structures of the ligand-free protein and of its complex with CDP (PDB codes and, respectively) were compared to the crystal structure of UMP/CMP kinase from Dictyostelium discoideum complexed with substrates (PDB code ). The key residues for ATP/ADP binding to CMPK(coli) were identified as R157 and I209, their side chains sandwiching the adenine ring. Moreover, the residues involved in the fixation of the phosphate groups are conserved in both proteins. In the model, the accessibility of the fluorescent ring to the solvent should be substantial if the LID conformation remained unchanged, by contrast to the fluorescence data. These results provide the first experimental arguments about an ATP-mediated induced-fit of the LID in CMPK(coli) modulated by CMP, leading to a closed conformation of the active site, protected from water.

Backend Control Processor for a Multi-Processor Relational Database Computer System.

DTIC Science & Technology

1984-12-01

SCHOOL OF ENGI. UNCRSIFID MPONTIFF DEC 84 AFXT/GCS/ENG/84D-22 F/O 9/2 L ommhhhhmhhml mhhhommhhhhhm i-2 8 -- U0. 11111= Q. 2 111.8IIII- 1111111..6...THESIS Presented to the Faculty of the School of Engineering of the Air Force Institute of Technology Air University In Partial Fulfillment of the...development of a Backend Multi-Processor Relational Database Computer System. This thesis addresses a single component of this system, the Backend Control

Visual monitoring of autonomous life sciences experimentation

NASA Technical Reports Server (NTRS)

Blank, G. E.; Martin, W. N.

1987-01-01

The design and implementation of a computerized visual monitoring system to aid in the monitoring and control of life sciences experiments on board a space station was investigated. A likely multiprocessor design was chosen, a plausible life science experiment with which to work was defined, the theoretical issues involved in the programming of a visual monitoring system for the experiment was considered on the multiprocessor, a system for monitoring the experiment was designed, and simulations of such a system was implemented on a network of Apollo workstations.

A CAMAC-VME-Macintosh data acquisition system for nuclear experiments

NASA Astrophysics Data System (ADS)

Anzalone, A.; Giustolisi, F.

1989-10-01

A multiprocessor system for data acquisition and analysis in low-energy nuclear physics has been realized. The system is built around CAMAC, the VMEbus, and the Macintosh PC. Multiprocessor software has been developed, using RTF, MACsys, and CERN cross-software. The execution of several programs that run on several VME CPUs and on an external PC is coordinated by a mailbox protocol. No operating system is used on the VME CPUs. The hardware, software, and system performance are described.

Performance Evaluation of Parallel Algorithms and Architectures in Concurrent Multiprocessor Systems

DTIC Science & Technology

1988-09-01

HEP and Other Parallel processors, Report no. ANL-83-97, Argonne National Laboratory, Argonne, Ill. 1983. [19] Davidson, G . S. A Practical Paradigm for...IEEE Comp. Soc., 1986. [241 Peir, Jih-kwon, and D. Gajski , "CAMP: A Programming Aide For Multiprocessors," Proc. 1986 ICPP, IEEE Comp. Soc., pp475...482. [251 Pfister, G . F., and V. A. Norton, "Hot Spot Contention and Combining in Multistage Interconnection Networks,"IEEE Trans. Comp., C-34, Oct

Advanced metrology by offline SEM data processing

NASA Astrophysics Data System (ADS)

Lakcher, Amine; Schneider, Loïc.; Le-Gratiet, Bertrand; Ducoté, Julien; Farys, Vincent; Besacier, Maxime

2017-06-01

Today's technology nodes contain more and more complex designs bringing increasing challenges to chip manufacturing process steps. It is necessary to have an efficient metrology to assess process variability of these complex patterns and thus extract relevant data to generate process aware design rules and to improve OPC models. Today process variability is mostly addressed through the analysis of in-line monitoring features which are often designed to support robust measurements and as a consequence are not always very representative of critical design rules. CD-SEM is the main CD metrology technique used in chip manufacturing process but it is challenged when it comes to measure metrics like tip to tip, tip to line, areas or necking in high quantity and with robustness. CD-SEM images contain a lot of information that is not always used in metrology. Suppliers have provided tools that allow engineers to extract the SEM contours of their features and to convert them into a GDS. Contours can be seen as the signature of the shape as it contains all the dimensional data. Thus the methodology is to use the CD-SEM to take high quality images then generate SEM contours and create a data base out of them. Contours are used to feed an offline metrology tool that will process them to extract different metrics. It was shown in two previous papers that it is possible to perform complex measurements on hotspots at different process steps (lithography, etch, copper CMP) by using SEM contours with an in-house offline metrology tool. In the current paper, the methodology presented previously will be expanded to improve its robustness and combined with the use of phylogeny to classify the SEM images according to their geometrical proximities.

Abnormal fault-recovery characteristics of the fault-tolerant multiprocessor uncovered using a new fault-injection methodology

NASA Technical Reports Server (NTRS)

Padilla, Peter A.

1991-01-01

An investigation was made in AIRLAB of the fault handling performance of the Fault Tolerant MultiProcessor (FTMP). Fault handling errors detected during fault injection experiments were characterized. In these fault injection experiments, the FTMP disabled a working unit instead of the faulted unit once in every 500 faults, on the average. System design weaknesses allow active faults to exercise a part of the fault management software that handles Byzantine or lying faults. Byzantine faults behave such that the faulted unit points to a working unit as the source of errors. The design's problems involve: (1) the design and interface between the simplex error detection hardware and the error processing software, (2) the functional capabilities of the FTMP system bus, and (3) the communication requirements of a multiprocessor architecture. These weak areas in the FTMP's design increase the probability that, for any hardware fault, a good line replacement unit (LRU) is mistakenly disabled by the fault management software.

A multiprocessor operating system simulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnston, G.M.; Campbell, R.H.

1988-01-01

This paper describes a multiprocessor operating system simulator that was developed by the authors in the Fall of 1987. The simulator was built in response to the need to provide students with an environment in which to build and test operating system concepts as part of the coursework of a third-year undergraduate operating systems course. Written in C++, the simulator uses the co-routine style task package that is distributed with the AT and T C++ Translator to provide a hierarchy of classes that represents a broad range of operating system software and hardware components. The class hierarchy closely follows thatmore » of the Choices family of operating systems for loosely and tightly coupled multiprocessors. During an operating system course, these classes are refined and specialized by students in homework assignments to facilitate experimentation with different aspects of operating system design and policy decisions. The current implementation runs on the IBM RT PC under 4.3bsd UNIX.« less

Solution of large nonlinear quasistatic structural mechanics problems on distributed-memory multiprocessor computers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blanford, M.

1997-12-31

Most commercially-available quasistatic finite element programs assemble element stiffnesses into a global stiffness matrix, then use a direct linear equation solver to obtain nodal displacements. However, for large problems (greater than a few hundred thousand degrees of freedom), the memory size and computation time required for this approach becomes prohibitive. Moreover, direct solution does not lend itself to the parallel processing needed for today`s multiprocessor systems. This talk gives an overview of the iterative solution strategy of JAS3D, the nonlinear large-deformation quasistatic finite element program. Because its architecture is derived from an explicit transient-dynamics code, it does not ever assemblemore » a global stiffness matrix. The author describes the approach he used to implement the solver on multiprocessor computers, and shows examples of problems run on hundreds of processors and more than a million degrees of freedom. Finally, he describes some of the work he is presently doing to address the challenges of iterative convergence for ill-conditioned problems.« less

Analysis of a Multiprocessor Guidance Computer. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Maltach, E. G.

1969-01-01

The design of the next generation of spaceborne digital computers is described. It analyzes a possible multiprocessor computer configuration. For the analysis, a set of representative space computing tasks was abstracted from the Lunar Module Guidance Computer programs as executed during the lunar landing, from the Apollo program. This computer performs at this time about 24 concurrent functions, with iteration rates from 10 times per second to once every two seconds. These jobs were tabulated in a machine-independent form, and statistics of the overall job set were obtained. It was concluded, based on a comparison of simulation and Markov results, that the Markov process analysis is accurate in predicting overall trends and in configuration comparisons, but does not provide useful detailed information in specific situations. Using both types of analysis, it was determined that the job scheduling function is a critical one for efficiency of the multiprocessor. It is recommended that research into the area of automatic job scheduling be performed.

Tetraphenylethylene-Interweaving Conjugated Macrocycle Polymer Materials as Two-Photon Fluorescence Sensors for Metal Ions and Organic Molecules.

PubMed

Li, Xi; Li, Zheng; Yang, Ying-Wei

2018-05-01

A luminescent conjugated macrocycle polymer (CMP) with strong two-photon fluorescence property, namely, P[5]-TPE-CMP, is constructed from ditriflate-functionalized pillar[5]arene and a 1,1,2,2-tetrakis(4-ethynylphenyl)ethylene (TPE) linker through a Sonogashira-Hagihara cross-coupling reaction. Significantly, in sharp contrast with the corresponding conjugated microporous polymer without synthetic macrocycles, P[5]-TPE-CMP shows an outstanding stability against photobleaching and exhibits highly selective cation sensing capability toward Fe 3+ at different excitation wavelengths (both UV and red-near-infrared regions). Meanwhile, its fluorescence could also be sufficiently quenched by 4-amino azobenzene, a frequently used organic dye that is certified to be carcinogenic, as compared with a group of common organic compounds. This work paves a new way for enhancing the properties of porous organic polymers through the introduction of supramolecular macrocycles like macrocyclic arenes. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development of chitosan-pullulan composite nanoparticles for nasal delivery of vaccines: in vivo studies.

PubMed

Cevher, Erdal; Salomon, Stefan K; Somavarapu, Satyanarayana; Brocchini, Steve; Alpar, H Oya

2015-01-01

Here, we aimed at developing chitosan/pullulan composite nanoparticles and testing their potential as novel systems for the nasal delivery of diphtheria toxoid (DT). All the chitosan derivatives [N-trimethyl (TMC), chloride and glutamate] and carboxymethyl pullulan (CMP) were synthesised and antigen-loaded composites were prepared by polyion complexation of chitosan and pullulan derivatives (particle size: 239-405 nm; surface charge: +18 and +27 mV). Their immunological effects after intranasal administration to mice were compared to intramuscular route. Composite nanoparticles induced higher levels of IgG responses than particles formed with chitosan derivative and antigen. Nasally administered TMC-pullulan composites showed higher DT serum IgG titre when compared with the other composites. Co-encapsulation of CpG ODN within TMC-CMP-DT nanoparticles resulted in a balanced Th1/Th2 response. TMC/pullulan composite nanoparticles also induced highest cytokine levels compared to those of chitosan salts. These findings demonstrated that TMC-CMP-DT composite nanoparticles are promising delivery system for nasal vaccination.

Effects of the Physical Characteristics of Cerium Oxide on Plasma-Enhanced Tetraethylorthosiliate Removal Rate of Chemical Mechanical Polishing for Shallow Trench Isolation

NASA Astrophysics Data System (ADS)

Kim, Sang-Kyun; Paik, Ungyu; Oh, Seong-Geun; Park, Yong-Kook; Katoh, Takeo; Park, Jea-Gun

2003-03-01

Ceria powders were synthesized by two different methods, solid-state displacement reaction and wet chemical precipitation, and the influence of the physical characteristics of cerium oxide on the removal rate of plasma-enhanced tetraethylorthosilicate (PETEOS) and chemical vapor deposition (CVD) nitride films in chemical mechanical planarization (CMP) was investigated. The fundamental physicochemical property and electrokinetic behavior of ceria particles in aqueous suspending media were investigated to identify the correlation between the colloidal property of ceria and the CMP performance. The surface potentials of two different ceria particles are found to have different isoelectric point (pHiep) values and differences in physical properties of ceria particles such as porosity and density were found to be the key parameters in CMP of PETEOS films. Ceria powders synthesized by the solid-state displacement reaction method yielded a higher removal rate of PETEOS and higher selectivity than powders synthesized by the wet chemical precipitation method.

TRMM Common Microphysics Products: A Tool for Evaluating Spaceborne Precipitation Retrieval Algorithms

NASA Technical Reports Server (NTRS)

Kingsmill, David E.; Yuter, Sandra E.; Hobbs, Peter V.; Rangno, Arthur L.; Heymsfield, Andrew J.; Stith, Jeffrey L.; Bansemer, Aaron; Haggerty, Julie A.; Korolev, Alexei V.

2004-01-01

A customized product for analysis of microphysics data collected from aircraft during field campaigns in support of the TRMM program is described. These Common Microphysics Products (CMP's) are designed to aid in evaluation of TRMM spaceborne precipitation retrieval algorithms. Information needed for this purpose (e.g., particle size spectra and habit, liquid and ice water content) was derived using a common processing strategy on the wide variety of microphysical instruments and raw native data formats employed in the field campaigns. The CMP's are organized into an ASCII structure to allow easy access to the data for those less familiar with and without the tools to accomplish microphysical data processing. Detailed examples of the CMP show its potential and some of its limitations. This approach may be a first step toward developing a generalized microphysics format and an associated community-oriented, non-proprietary software package for microphysics data processing, initiatives that would likely broaden community access to and use of microphysics datasets.

Recent results on output feedback problems

NASA Technical Reports Server (NTRS)

Byrnes, C. I.

1980-01-01

Given a real linear system sigma = (A, B, C) with m inputs, p outputs and degree n, the problem of generic pole placement by output feedback is studied, which is to compute the constant C(m,p) such that the inequality C(m,p) not less than n is necessary and sufficient for generically positioning the poles of the generic linear system by constant output feedback. A constant C prime (m,p) is determined, which gives a sufficient condition for generic pole placement and which, to the best of the author's knowledge, is at least as good an estimate of C(m,p) as any in the literature. Some results on the construction of solutions in case mp = n are announced, based on the degree formula of Brockett and Byrnes and the Galois theory. In particular, a question raised by Anderson, Bose, and Jury, on the existence of a rational procedure for computing the feedback law from the desired characteristic polynomial is answered.

Benzotriazole removal on post-Cu CMP cleaning

NASA Astrophysics Data System (ADS)

Jiying, Tang; Yuling, Liu; Ming, Sun; Shiyan, Fan; Yan, Li

2015-06-01

This work investigates systematically the effect of FA/O II chelating agent and FA/O I surfactant in alkaline cleaning solutions on benzotriazole (BTA) removal during post-Cu CMP cleaning in GLSI under the condition of static etching. The best detergent formulation for BTA removal can be determined by optimization of the experiments of single factor and compound cleaning solution, which has been further confirmed experimentally by contact angle (CA) measurements. The resulting solution with the best formulation has been measured for the actual production line, and the results demonstrate that the obtained cleaning solution can effectively and efficiently remove BTA, CuO and abrasive SiO2 without basically causing interfacial corrosion. This work demonstrates the possibility of developing a simple, low-cost and environmentally-friendly cleaning solution to effectively solve the issues of BTA removal on post-Cu CMP cleaning in a multi-layered copper wafer. Project supported by the Major National Science and Technology Special Projects (No. 2009ZX02308).

A novel approach of chemical mechanical polishing for cadmium zinc telluride wafers.

PubMed

Zhang, Zhenyu; Wang, Bo; Zhou, Ping; Kang, Renke; Zhang, Bi; Guo, Dongming

2016-05-26

A novel approach of chemical mechanical polishing (CMP) is developed for cadmium zinc telluride (CdZnTe or CZT) wafers. The approach uses environment-friendly slurry that consists of mainly silica, hydrogen peroxide, and citric acid. This is different from the previously reported slurries that are usually composed of strong acid, alkali, and bromine methanol, and are detrimental to the environment and operators. Surface roughness 0.5 nm and 4.7 nm are achieved for Ra and peak-to-valley (PV) values respectively in a measurement area of 70 × 50 μm(2), using the developed novel approach. Fundamental polishing mechanisms are also investigated in terms of X-ray photoelectron spectroscopy (XPS) and electrochemical measurements. Hydrogen peroxide dominates the passivating process during the CMP of CZT wafers, indicating by the lowest passivation current density among silica, citric acid and hydrogen peroxide solution. Chemical reaction equations are proposed during CMP according to the XPS and electrochemical measurements.

A novel approach of chemical mechanical polishing for cadmium zinc telluride wafers

PubMed Central

Zhang, Zhenyu; Wang, Bo; Zhou, Ping; Kang, Renke; Zhang, Bi; Guo, Dongming

2016-01-01

A novel approach of chemical mechanical polishing (CMP) is developed for cadmium zinc telluride (CdZnTe or CZT) wafers. The approach uses environment-friendly slurry that consists of mainly silica, hydrogen peroxide, and citric acid. This is different from the previously reported slurries that are usually composed of strong acid, alkali, and bromine methanol, and are detrimental to the environment and operators. Surface roughness 0.5 nm and 4.7 nm are achieved for Ra and peak-to-valley (PV) values respectively in a measurement area of 70 × 50 μm2, using the developed novel approach. Fundamental polishing mechanisms are also investigated in terms of X-ray photoelectron spectroscopy (XPS) and electrochemical measurements. Hydrogen peroxide dominates the passivating process during the CMP of CZT wafers, indicating by the lowest passivation current density among silica, citric acid and hydrogen peroxide solution. Chemical reaction equations are proposed during CMP according to the XPS and electrochemical measurements. PMID:27225310

OSCAR API for Real-Time Low-Power Multicores and Its Performance on Multicores and SMP Servers

NASA Astrophysics Data System (ADS)

Kimura, Keiji; Mase, Masayoshi; Mikami, Hiroki; Miyamoto, Takamichi; Shirako, Jun; Kasahara, Hironori

OSCAR (Optimally Scheduled Advanced Multiprocessor) API has been designed for real-time embedded low-power multicores to generate parallel programs for various multicores from different vendors by using the OSCAR parallelizing compiler. The OSCAR API has been developed by Waseda University in collaboration with Fujitsu Laboratory, Hitachi, NEC, Panasonic, Renesas Technology, and Toshiba in an METI/NEDO project entitled "Multicore Technology for Realtime Consumer Electronics." By using the OSCAR API as an interface between the OSCAR compiler and backend compilers, the OSCAR compiler enables hierarchical multigrain parallel processing with memory optimization under capacity restriction for cache memory, local memory, distributed shared memory, and on-chip/off-chip shared memory; data transfer using a DMA controller; and power reduction control using DVFS (Dynamic Voltage and Frequency Scaling), clock gating, and power gating for various embedded multicores. In addition, a parallelized program automatically generated by the OSCAR compiler with OSCAR API can be compiled by the ordinary OpenMP compilers since the OSCAR API is designed on a subset of the OpenMP. This paper describes the OSCAR API and its compatibility with the OSCAR compiler by showing code examples. Performance evaluations of the OSCAR compiler and the OSCAR API are carried out using an IBM Power5+ workstation, an IBM Power6 high-end SMP server, and a newly developed consumer electronics multicore chip RP2 by Renesas, Hitachi and Waseda. From the results of scalability evaluation, it is found that on an average, the OSCAR compiler with the OSCAR API can exploit 5.8 times speedup over the sequential execution on the Power5+ workstation with eight cores and 2.9 times speedup on RP2 with four cores, respectively. In addition, the OSCAR compiler can accelerate an IBM XL Fortran compiler up to 3.3 times on the Power6 SMP server. Due to low-power optimization on RP2, the OSCAR compiler with the OSCAR API achieves a maximum power reduction of 84% in the real-time execution mode.

A macrochip interconnection network enabled by silicon nanophotonic devices.

PubMed

Zheng, Xuezhe; Cunningham, John E; Koka, Pranay; Schwetman, Herb; Lexau, Jon; Ho, Ron; Shubin, Ivan; Krishnamoorthy, Ashok V; Yao, Jin; Mekis, Attila; Pinguet, Thierry

2010-03-01

We present an advanced wavelength-division multiplexing point-to-point network enabled by silicon nanophotonic devices. This network offers strictly non-blocking all-to-all connectivity while maximizing bisection bandwidth, making it ideal for multi-core and multi-processor interconnections. We introduce one of the key components, the nanophotonic grating coupler, and discuss, for the first time, how this device can be useful for practical implementations of the wavelength-division multiplexing network using optical proximity communications. Finite difference time-domain simulation of the nanophotonic grating coupler device indicates that it can be made compact (20 microm x 50 microm), low loss (3.8 dB), and broadband (100 nm). These couplers require subwavelength material modulation at the nanoscale to achieve the desired functionality. We show that optical proximity communication provides unmatched optical I/O bandwidth density to electrical chips, which enables the application of wavelength-division multiplexing point-to-point network in macrochip with unprecedented bandwidth-density. The envisioned physical implementation is discussed. The benefits of such an interconnect network include a 5-6x improvement in latency when compared to a purely electronic implementation. Performance analysis shows that the wavelength-division multiplexing point-to-point network offers better overall performance over other optical network architectures.

Implementation of MPEG-2 encoder to multiprocessor system using multiple MVPs (TMS320C80)

NASA Astrophysics Data System (ADS)

Kim, HyungSun; Boo, Kenny; Chung, SeokWoo; Choi, Geon Y.; Lee, YongJin; Jeon, JaeHo; Park, Hyun Wook

1997-05-01

This paper presents the efficient algorithm mapping for the real-time MPEG-2 encoding on the KAIST image computing system (KICS), which has a parallel architecture using five multimedia video processors (MVPs). The MVP is a general purpose digital signal processor (DSP) of Texas Instrument. It combines one floating-point processor and four fixed- point DSPs on a single chip. The KICS uses the MVP as a primary processing element (PE). Two PEs form a cluster, and there are two processing clusters in the KICS. Real-time MPEG-2 encoder is implemented through the spatial and the functional partitioning strategies. Encoding process of spatially partitioned half of the video input frame is assigned to ne processing cluster. Two PEs perform the functionally partitioned MPEG-2 encoding tasks in the pipelined operation mode. One PE of a cluster carries out the transform coding part and the other performs the predictive coding part of the MPEG-2 encoding algorithm. One MVP among five MVPs is used for system control and interface with host computer. This paper introduces an implementation of the MPEG-2 algorithm with a parallel processing architecture.

Customers' perspectives on the impact of the Pathways to Work condition management programme on their health, well-being and vocational activity.

PubMed

Secker, Jenny; Pittam, Gail; Ford, Fiona

2012-11-01

Pathways to Work is a UK initiative aimed at supporting customers on incapacity benefits to return to work. This qualitative study complements previous evaluations of Pathways to Work by exploring customers' perceptions of the impact of the Condition Management Programme (CMP) offered to claimants with long-term health conditions. 39 customers took part in focus groups held at the seven sites where Pathways was originally piloted. The main focus of the discussions was on perceptions of the ways in which participation had impacted on health, well-being and return to work. The discussions were audio-recorded and fully transcribed for analysis using a text analysis framework to enable the development and refinement of categories and overarching patterns in the data. Perceived impacts on health and well-being included a more positive outlook, social contact, changed perceptions of conditions and improvements in health. Some customers also reported an increase in their vocational activity and others felt ready to embark on new activities. Factors associated with positive outcomes included the extent and quality of contact with CMP staff and practical advice about condition management. Factors impeding positive employment outcomes related mainly to obstacles to returning to work. The results indicated that CMP can assist customers to learn about and manage their health conditions and increase their vocational activity, and that CMP therefore provides a promising means of enabling people with long-term health conditions to regain a fulfilling, productive life.

The Electronic CardioMetabolic Program (eCMP) for Patients With Cardiometabolic Risk: A Randomized Controlled Trial.

PubMed

Azar, Kristen M J; Koliwad, Suneil; Poon, Tak; Xiao, Lan; Lv, Nan; Griggs, Robert; Ma, Jun

2016-05-27

Effective lifestyle interventions targeting high-risk adults that are both practical for use in ambulatory care settings and scalable at a population management level are needed. Our aim was to examine the potential effectiveness, feasibility, and acceptability of delivering an evidence-based Electronic Cardio-Metabolic Program (eCMP) for improving health-related quality of life, improving health behaviors, and reducing cardiometabolic risk factors in ambulatory care high-risk adults. We conducted a randomized, wait-list controlled trial with 74 adults aged ≥18 years recruited from a large multispecialty health care organization. Inclusion criteria were (1) BMI ≥35 kg/m(2) and prediabetes, previous gestational diabetes and/or metabolic syndrome, or (2) BMI ≥30 kg/m(2) and type 2 diabetes and/or cardiovascular disease. Participants had a mean age of 59.7 years (SD 11.2), BMI 37.1 kg/m(2) (SD 5.4) and were 59.5% female, 82.4% white. Participants were randomized to participate in eCMP immediately (n=37) or 3 months later (n=37). eCMP is a 6-month program utilizing video conferencing, online tools, and pre-recorded didactic videos to deliver evidence-based curricula. Blinded outcome assessments were conducted at 3 and 6 months postbaseline. Data were collected and analyzed between 2014 and 2015. The primary outcome was health-related quality of life. Secondary outcomes included biometric cardiometabolic risk factors (eg, body weight), self-reported diet and physical activity, mental health status, retention, session attendance, and participant satisfaction. Change in quality of life was not significant in both immediate and delayed participants. Both groups significantly lost weight and reduced waist circumference at 6 months, with some cardiometabolic factors trending accordingly. Significant reduction in self-reported anxiety and perceived stress was seen in the immediate intervention group at 6 months. Retention rate was 93% at 3 months and 86% at 6 months post-baseline. Overall eCMP attendance was high with 59.5-83.8% of immediate and delayed intervention participants attending 50% of the virtual stress management and behavioral lifestyle sessions and 37.8-62.2% attending at least 4 out of 7 in-person physical activity sessions. The intervention received high ratings for satisfaction. The technology-assisted eCMP is a feasible and well-accepted intervention and may significantly decrease cardiometabolic risk among high-risk individuals. Clinicaltrials.gov NCT02246400; https://clinicaltrials.gov/ct2/show/NCT02246400 (Archived by WebCite at http://www.webcitation.org/6h6mWWokP).

Tribochemical investigation of microelectronic materials

NASA Astrophysics Data System (ADS)

Kulkarni, Milind Sudhakar

To achieve efficient planarization with reduced device dimensions in integrated circuits, a better understanding of the physics, chemistry, and the complex interplay involved in chemical mechanical planarization (CMP) is needed. The CMP process takes place at the interface of the pad and wafer in the presence of the fluid slurry medium. The hardness of Cu is significantly less than the slurry abrasive particles which are usually alumina or silica. It has been accepted that a surface layer can protect the Cu surface from scratching during CMP. Four competing mechanisms in materials removal have been reported: the chemical dissolution of Cu, the mechanical removal through slurry abrasives, the formation of thin layer of Cu oxide and the sweeping surface material by slurry flow. Despite the previous investigation of Cu removal, the electrochemical properties of Cu surface layer is yet to be understood. The motivation of this research was to understand the fundamental aspects of removal mechanisms in terms of electrochemical interactions, chemical dissolution, mechanical wear, and factors affecting planarization. Since one of the major requirements in CMP is to have a high surface finish, i.e., low surface roughness, optimization of the surface finish in reference to various parameters was emphasized. Three approaches were used in this research: in situ measurement of material removal, exploration of the electropotential activation and passivation at the copper surface and modeling of the synergistic electrochemical-mechanical interactions on the copper surface. In this research, copper polishing experiments were conducted using a table top tribometer. A potentiostat was coupled with this tribometer. This combination enabled the evaluation of important variables such as applied pressure, polishing speed, slurry chemistry, pH, materials, and applied DC potential. Experiments were designed to understand the combined and individual effect of electrochemical interactions as well as mechanical impact during polishing. Extensive surface characterization was performed with AFM, SEM, TEM and XPS. An innovative method for direct material removal measurement on the nanometer scale was developed and used. Experimental observations were compared with the theoretically calculated material removal rate values. The synergistic effect of all of the components of the process, which result in a better quality surface finish was quantitatively evaluated for the first time. Impressed potential during CMP proved to be a controlling parameter in the material removal mechanism. Using the experimental results, a model was developed, which provided a practical insight into the CMP process. The research is expected to help with electrochemical material removal in copper planarization with low-k dielectrics.

A language comparison for scientific computing on MIMD architectures

NASA Technical Reports Server (NTRS)

Jones, Mark T.; Patrick, Merrell L.; Voigt, Robert G.

1989-01-01

Choleski's method for solving banded symmetric, positive definite systems is implemented on a multiprocessor computer using three FORTRAN based parallel programming languages, the Force, PISCES and Concurrent FORTRAN. The capabilities of the language for expressing parallelism and their user friendliness are discussed, including readability of the code, debugging assistance offered, and expressiveness of the languages. The performance of the different implementations is compared. It is argued that PISCES, using the Force for medium-grained parallelism, is the appropriate choice for programming Choleski's method on the multiprocessor computer, Flex/32.

The MSFC UNIVAC 1108 EXEC 8 simulation model

NASA Technical Reports Server (NTRS)

Williams, T. G.; Richards, F. M.; Weatherbee, J. E.; Paul, L. K.

1972-01-01

A model is presented which simulates the MSFC Univac 1108 multiprocessor system. The hardware/operating system is described to enable a good statistical measurement of the system behavior. The performance of the 1108 is evaluated by performing twenty-four different experiments designed to locate system bottlenecks and also to test the sensitivity of system throughput with respect to perturbation of the various Exec 8 scheduling algorithms. The model is implemented in the general purpose system simulation language and the techniques described can be used to assist in the design, development, and evaluation of multiprocessor systems.

Generation-based memory synchronization in a multiprocessor system with weakly consistent memory accesses

DOEpatents

Ohmacht, Martin

2017-08-15

In a multiprocessor system, a central memory synchronization module coordinates memory synchronization requests responsive to memory access requests in flight, a generation counter, and a reclaim pointer. The central module communicates via point-to-point communication. The module includes a global OR reduce tree for each memory access requesting device, for detecting memory access requests in flight. An interface unit is implemented associated with each processor requesting synchronization. The interface unit includes multiple generation completion detectors. The generation count and reclaim pointer do not pass one another.

Generation-based memory synchronization in a multiprocessor system with weakly consistent memory accesses

DOEpatents

Ohmacht, Martin

2014-09-09

In a multiprocessor system, a central memory synchronization module coordinates memory synchronization requests responsive to memory access requests in flight, a generation counter, and a reclaim pointer. The central module communicates via point-to-point communication. The module includes a global OR reduce tree for each memory access requesting device, for detecting memory access requests in flight. An interface unit is implemented associated with each processor requesting synchronization. The interface unit includes multiple generation completion detectors. The generation count and reclaim pointer do not pass one another.

Multiprocessor system with multiple concurrent modes of execution

DOEpatents

Ahn, Daniel; Ceze, Luis H; Chen, Dong; Gara, Alan; Heidelberger, Philip; Ohmacht, Martin

2013-12-31

A multiprocessor system supports multiple concurrent modes of speculative execution. Speculation identification numbers (IDs) are allocated to speculative threads from a pool of available numbers. The pool is divided into domains, with each domain being assigned to a mode of speculation. Modes of speculation include TM, TLS, and rollback. Allocation of the IDs is carried out with respect to a central state table and using hardware pointers. The IDs are used for writing different versions of speculative results in different ways of a set in a cache memory.

Multiprocessor system with multiple concurrent modes of execution

DOEpatents

Ahn, Daniel; Ceze, Luis H.; Chen, Dong Chen; Gara, Alan; Heidelberger, Philip; Ohmacht, Martin

2016-11-22

A multiprocessor system supports multiple concurrent modes of speculative execution. Speculation identification numbers (IDs) are allocated to speculative threads from a pool of available numbers. The pool is divided into domains, with each domain being assigned to a mode of speculation. Modes of speculation include TM, TLS, and rollback. Allocation of the IDs is carried out with respect to a central state table and using hardware pointers. The IDs are used for writing different versions of speculative results in different ways of a set in a cache memory.

Soluble minerals in chemical evolution. II - Characterization of the adsorption of 5-prime-AMP and 5-prime-CMP on a variety of soluble mineral salts

NASA Technical Reports Server (NTRS)

Chan, Stephen; Orenberg, James; Lahav, Noam

1987-01-01

The adsorption of 5-prime-AMP and 5-prime-CMP is studied in the saturated solutions of several mineral salts as a function of pH, ionic strength, and surface area of the solid salt. It is suggested that the adsorption which results from the binding between the nucleotide molecule and the salt surface is due to electrostatic forces. The adsorption is reversible in nature and decreases with increasing ionic strength.

SEMICONDUCTOR TECHNOLOGY: Material removal rate in chemical-mechanical polishing of wafers based on particle trajectories

NASA Astrophysics Data System (ADS)

Jianxiu, Su; Xiqu, Chen; Jiaxi, Du; Renke, Kang

2010-05-01

Distribution forms of abrasives in the chemical mechanical polishing (CMP) process are analyzed based on experimental results. Then the relationships between the wafer, the abrasive and the polishing pad are analyzed based on kinematics and contact mechanics. According to the track length of abrasives on the wafer surface, the relationships between the material removal rate and the polishing velocity are obtained. The analysis results are in accord with the experimental results. The conclusion provides a theoretical guide for further understanding the material removal mechanism of wafers in CMP.

Novel bio-synthetic hybrid materials and coculture systems for musculoskeletal tissue engineering

NASA Astrophysics Data System (ADS)

Lee, Hyeseung Janice

Tissue Engineering is a truly exciting field of this age, trying to regenerate and repair impaired tissues. Unlike the old artificial implants, tissue engineering aims at making a long-term functional biological replacement. One strategy for such tissue engineering requires the following three components: cells, scaffolds, and soluble factors. Cells are cultured in a three-dimensional (3D) scaffold with medium containing various soluble factors. Once a tissue is developed in vitro, then it is implanted in vivo. The overall goal of this thesis was to develop novel bio-synthetic hybrid scaffolds and coculture system for musculoskeletal tissue engineering. The most abundant cartilage extracellular matrix (ECM) components are collagen and glycosaminoglycan (GAG), which are the natural scaffold for chondrocytes. As two different peptides, collagen mimetic peptide (CMP) and hyaluronic acid binding peptide (HABPep) were previously shown to bind to collagen and hyaluronic acid (HA) of GAG, respectively, it was hypothesized that immobilizing CMP and HABP on 3D scaffold would results in an interaction between ECM components and synthetic scaffolds via peptide-ECM bindings. CMP or HABPep-conjugated photopolymerizable poly(ethylene oxide) diacrylate (PEODA) hydrogels were synthesized and shown to retain encapsulated collagen or HA, respectively. This result supported that conjugated CMP and HABPep can interact with collagen and HA, respectively, and can serve as biological linkers in 3D synthetic hydrogels. When chondrocytes or mesenchymal stem cells (MSCs) were seeded, cells in CMP-conjugated scaffolds produced significantly more amount of type II collagen and GAG, compared to those in control scaffolds. Moreover, MSCs cultured in CMP-conjugated scaffolds exhibited lower level of hypertrophic markers, cbfa-1 and type X collagen. These results demonstrated that enhanced interaction between collagen and scaffold via CMP improves chondrogenesis of chondrocytes and MSCs and further reduces hypertrophy of differentiating MSCs. On the other hand, although cells in HABPep-conjugated scaffolds produced less ECM components, they survived and proliferated significantly more than those in control, resulting in overall increase in ECM contents per scaffold. Once implanted in vivo, HABPep-conjugated constructs increased GAG and type II collagen contents further, compared to those of the control hydrogel. These results showed that enhanced interaction between HA and scaffold via HABPep improved the in vitro culture expansion of MSCs and further ECM production in vivo. Effects of cell-secreted bioactive factors via cell-cell communication on stem cell differentiation were also investigated in 3D bilayer system. First, when mesenchymal progenitor cells (MPCs) were cocultured with ES-derived cells (ESDC), morphogenetic factors secreted by ESDCs showed a potential to improve MPC chondrogenesis in both control and chondrogenic medium by increasing not only MPC's chondrogenic gene expression, but also ECM production. Moreover, the effect of ESDC cell-mediated chondrogenesis of MSC could not be mimicked by chondrogenic medium supplemented with TGF-beta1 and dexamethasone. Secondly, coculturing hepatic cells enhanced specific chondrogenic differentiation of ES cells in the 3D bilayer system. These studies demonstrated that cell-secreted soluble factors can be used to guide stem cell differentiation.

Spin dynamics in the modulation frame: application to homonuclear recoupling in magic angle spinning solid-state NMR.

PubMed

De Paëpe, Gaël; Lewandowski, Józef R; Griffin, Robert G

2008-03-28

We introduce a family of solid-state NMR pulse sequences that generalizes the concept of second averaging in the modulation frame and therefore provides a new approach to perform magic angle spinning dipolar recoupling experiments. Here, we focus on two particular recoupling mechanisms-cosine modulated rotary resonance (CMpRR) and cosine modulated recoupling with isotropic chemical shift reintroduction (COMICS). The first technique, CMpRR, is based on a cosine modulation of the rf phase and yields broadband double-quantum (DQ) (13)C recoupling using >70 kHz omega(1,C)/2pi rf field for the spinning frequency omega(r)/2=10-30 kHz and (1)H Larmor frequency omega(0,H)/2pi up to 900 MHz. Importantly, for p>or=5, CMpRR recouples efficiently in the absence of (1)H decoupling. Extension to lower p values (3.5

Luminescence properties and energy transfer of site-sensitive Ca(6-x-y)Mg(x-z)(PO(4))(4):Eu(y)(2+),Mn(z)(2+) phosphors and their application to near-UV LED-based white LEDs.

PubMed

Kwon, Ki Hyuk; Im, Won Bin; Jang, Ho Seong; Yoo, Hyoung Sun; Jeon, Duk Young

2009-12-21

On the basis of the structural information that the host material has excellent charge stabilization, blue-emitting Ca(6-x-y)Mg(x)(PO(4))(4):Eu(y)(2+) (CMP:Eu(2+)) phosphors were synthesized and systematically optimized, and their photoluminescence (PL) properties were evaluated. Depending upon the amount of Mg added, the emission efficiency of the phosphors could be enhanced. The substitution of Eu(2+) affected their maximum wavelength (lambda(max)) and thermal stability because the substitution site of Eu(2+) could be varied. To obtain single-phase two-color-emitting phosphors, we incorporated Mn(2+) into CMP:Eu(2+) phosphors. Weak red emission resulting from the forbidden transition of Mn(2+) could be enhanced by the energy transfer from Eu(2+) to Mn(2+) that occurs because of the spectral overlap between the photoluminescence excitation (PLE) spectrum of Mn(2+) and the PL spectrum of Eu(2+). The energy transfer process was confirmed by the luminescence spectra, energy transfer efficiency, and decay curve of the phosphors. Finally, the optimized Ca(6-x-y)Mg(x-z)(PO(4))(4):Eu(y)(2+),Mn(z)(2+) (CMP:Eu(2+),Mn(2+)) phosphors were applied with green emitting Ca(2)MgSi(2)O(7):Eu(2+) (CMS:Eu(2+)) phosphors to ultraviolet (UV) light emitting diode (LED)-pumped white LEDs. The CMS:Eu(2+)-mixed CMP:Eu(2+), Mn(2+)-based white LEDs showed an excellent color rendering index (CRI) of 98 because of the broader emission band and more stable color coordinates than those of commercial Y(3)Al(5)O(12):Ce(3+) (YAG:Ce(3+))-based white LEDs under a forward bias current of 20 mA. The fabricated white LEDs showed very bright natural white light that had the color coordinate of (0.3288, 0.3401), and thus CMP:Eu(2+),Mn(2+) could be regarded as a good candidate for UV LED-based white LEDs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gustafsson, Helena; Runesson, Johan; Lundqvist, Jessica

The objective of the EU-funded integrated project ACuteTox is to develop a strategy in which general cytotoxicity, together with organ-specific toxicity and biokinetic features, are used for the estimation of human acute systemic toxicity. Our role in the project is to characterise the effect of reference chemicals with regard to neurotoxicity. We studied cell membrane potential (CMP), noradrenalin (NA) uptake, acetylcholine esterase (AChE) activity, acetylcholine receptor (AChR) signalling and voltage-operated calcium channel (VOCC) function in human neuroblastoma SH-SY5Y cells after exposure to 23 pharmaceuticals, pesticides or industrial chemicals. Neurotoxic alert chemicals were identified by comparing the obtained data with cytotoxicitymore » data from the neutral red uptake assay in 3T3 mouse fibroblasts. Furthermore, neurotoxic concentrations were correlated with estimated human lethal blood concentrations (LC50). The CMP assay was the most sensitive assay, identifying eight chemicals as neurotoxic alerts and improving the LC50 correlation for nicotine, lindane, atropine and methadone. The NA uptake assay identified five neurotoxic alert chemicals and improved the LC50 correlation for atropine, diazepam, verapamil and methadone. The AChE, AChR and VOCC assays showed limited potential for detection of acute toxicity. The CMP assay was further evaluated by testing 36 additional reference chemicals. Five neurotoxic alert chemicals were generated and orphendrine and amitriptyline showed improved LC50 correlation. Due to the high sensitivity and the simplicity of the test protocol, the CMP assay constitutes a good candidate assay to be included in an in vitro test strategy for prediction of acute systemic toxicity.« less

High accuracy differential pressure measurements using fluid-filled catheters - A feasibility study in compliant tubes.

PubMed

Rotman, Oren Moshe; Weiss, Dar; Zaretsky, Uri; Shitzer, Avraham; Einav, Shmuel

2015-09-18

High accuracy differential pressure measurements are required in various biomedical and medical applications, such as in fluid-dynamic test systems, or in the cath-lab. Differential pressure measurements using fluid-filled catheters are relatively inexpensive, yet may be subjected to common mode pressure errors (CMP), which can significantly reduce the measurement accuracy. Recently, a novel correction method for high accuracy differential pressure measurements was presented, and was shown to effectively remove CMP distortions from measurements acquired in rigid tubes. The purpose of the present study was to test the feasibility of this correction method inside compliant tubes, which effectively simulate arteries. Two tubes with varying compliance were tested under dynamic flow and pressure conditions to cover the physiological range of radial distensibility in coronary arteries. A third, compliant model, with a 70% stenosis severity was additionally tested. Differential pressure measurements were acquired over a 3 cm tube length using a fluid-filled double-lumen catheter, and were corrected using the proposed CMP correction method. Validation of the corrected differential pressure signals was performed by comparison to differential pressure recordings taken via a direct connection to the compliant tubes, and by comparison to predicted differential pressure readings of matching fluid-structure interaction (FSI) computational simulations. The results show excellent agreement between the experimentally acquired and computationally determined differential pressure signals. This validates the application of the CMP correction method in compliant tubes of the physiological range for up to intermediate size stenosis severity of 70%. Copyright © 2015 Elsevier Ltd. All rights reserved.

The relationship of insulin resistance estimated by triglyceride glucose index and coronary plaque characteristics.

PubMed

Won, Ki-Bum; Kim, Yun Seok; Lee, Byoung Kwon; Heo, Ran; Han, Donghee; Lee, Ji Hyun; Lee, Sang-Eun; Sung, Ji Min; Cho, Iksung; Park, Hyung-Bok; Cho, In-Jeong; Chang, Hyuk-Jae

2018-05-01

The triglyceride glucose (TyG) index is a useful surrogate marker for insulin resistance, which is an important risk factor for coronary artery disease (CAD). However, data on the relationship of the TyG index and coronary plaque characteristics are limited.This study included 2840 participants with near-normal renal function who underwent coronary computed tomography angiography. CAD was defined as the presence of any plaques, and obstructive CAD was defined as the presence of plaques with ≥50% stenosis. The relationship between the TyG index and noncalcified plaque (NCP), calcified or mixed plaque (CMP), and coronary artery calcium score (CACS) was evaluated.All participants were stratified into 4 groups based on the quartiles of the TyG index. The prevalence of CAD and obstructive CAD significantly increased with increasing quartiles. The risk for NCP and obstructive NCP was not different among all groups. However, compared with group I (lowest quartile), the risk for CMP was higher in groups III (odds ratio [OR]: 1.438) and IV (highest quartile) (OR: 1.895) (P < .05), and that for obstructive CMP was higher in groups II (OR: 1.469), III (OR: 1.595), and IV (OR: 2.168) (P < .05). Multivariate regression analysis showed that the TyG index was associated with an increased risk for CAD (OR: 1.700), obstructive CAD (OR: 1.692), and CACS >400 (OR: 1.448) (P < .05).The TyG index was independently associated with the presence and severity of CAD due to an increased risk for CMP.

Development and evaluation of a Fault-Tolerant Multiprocessor (FTMP) computer. Volume 3: FTMP test and evaluation

NASA Technical Reports Server (NTRS)

Lala, J. H.; Smith, T. B., III

1983-01-01

The experimental test and evaluation of the Fault-Tolerant Multiprocessor (FTMP) is described. Major objectives of this exercise include expanding validation envelope, building confidence in the system, revealing any weaknesses in the architectural concepts and in their execution in hardware and software, and in general, stressing the hardware and software. To this end, pin-level faults were injected into one LRU of the FTMP and the FTMP response was measured in terms of fault detection, isolation, and recovery times. A total of 21,055 stuck-at-0, stuck-at-1 and invert-signal faults were injected in the CPU, memory, bus interface circuits, Bus Guardian Units, and voters and error latches. Of these, 17,418 were detected. At least 80 percent of undetected faults are estimated to be on unused pins. The multiprocessor identified all detected faults correctly and recovered successfully in each case. Total recovery time for all faults averaged a little over one second. This can be reduced to half a second by including appropriate self-tests.

Conference on Real-Time Computer Applications in Nuclear, Particle and Plasma Physics, 6th, Williamsburg, VA, May 15-19, 1989, Proceedings

NASA Technical Reports Server (NTRS)

Pordes, Ruth (Editor)

1989-01-01

Papers on real-time computer applications in nuclear, particle, and plasma physics are presented, covering topics such as expert systems tactics in testing FASTBUS segment interconnect modules, trigger control in a high energy physcis experiment, the FASTBUS read-out system for the Aleph time projection chamber, a multiprocessor data acquisition systems, DAQ software architecture for Aleph, a VME multiprocessor system for plasma control at the JT-60 upgrade, and a multiasking, multisinked, multiprocessor data acquisition front end. Other topics include real-time data reduction using a microVAX processor, a transputer based coprocessor for VEDAS, simulation of a macropipelined multi-CPU event processor for use in FASTBUS, a distributed VME control system for the LISA superconducting Linac, a distributed system for laboratory process automation, and a distributed system for laboratory process automation. Additional topics include a structure macro assembler for the event handler, a data acquisition and control system for Thomson scattering on ATF, remote procedure execution software for distributed systems, and a PC-based graphic display real-time particle beam uniformity.

Performances of multiprocessor multidisk architectures for continuous media storage

NASA Astrophysics Data System (ADS)

Gennart, Benoit A.; Messerli, Vincent; Hersch, Roger D.

1996-03-01

Multimedia interfaces increase the need for large image databases, capable of storing and reading streams of data with strict synchronicity and isochronicity requirements. In order to fulfill these requirements, we consider a parallel image server architecture which relies on arrays of intelligent disk nodes, each disk node being composed of one processor and one or more disks. This contribution analyzes through bottleneck performance evaluation and simulation the behavior of two multi-processor multi-disk architectures: a point-to-point architecture and a shared-bus architecture similar to current multiprocessor workstation architectures. We compare the two architectures on the basis of two multimedia algorithms: the compute-bound frame resizing by resampling and the data-bound disk-to-client stream transfer. The results suggest that the shared bus is a potential bottleneck despite its very high hardware throughput (400Mbytes/s) and that an architecture with addressable local memories located closely to their respective processors could partially remove this bottleneck. The point- to-point architecture is scalable and able to sustain high throughputs for simultaneous compute- bound and data-bound operations.

Communication Studies of DMP and SMP Machines

NASA Technical Reports Server (NTRS)

Sohn, Andrew; Biswas, Rupak; Chancellor, Marisa K. (Technical Monitor)

1997-01-01

Understanding the interplay between machines and problems is key to obtaining high performance on parallel machines. This paper investigates the interplay between programming paradigms and communication capabilities of parallel machines. In particular, we explicate the communication capabilities of the IBM SP-2 distributed-memory multiprocessor and the SGI PowerCHALLENGEarray symmetric multiprocessor. Two benchmark problems of bitonic sorting and Fast Fourier Transform are selected for experiments. Communication-efficient algorithms are developed to exploit the overlapping capabilities of the machines. Programs are written in Message-Passing Interface for portability and identical codes are used for both machines. Various data sizes and message sizes are used to test the machines' communication capabilities. Experimental results indicate that the communication performance of the multiprocessors are consistent with the size of messages. The SP-2 is sensitive to message size but yields a much higher communication overlapping because of the communication co-processor. The PowerCHALLENGEarray is not highly sensitive to message size and yields a low communication overlapping. Bitonic sorting yields lower performance compared to FFT due to a smaller computation-to-communication ratio.

A multiprocessor airborne lidar data system

NASA Technical Reports Server (NTRS)

Wright, C. W.; Bailey, S. A.; Heath, G. E.; Piazza, C. R.

1988-01-01

A new multiprocessor data acquisition system was developed for the existing Airborne Oceanographic Lidar (AOL). This implementation simultaneously utilizes five single board 68010 microcomputers, the UNIX system V operating system, and the real time executive VRTX. The original data acquisition system was implemented on a Hewlett Packard HP 21-MX 16 bit minicomputer using a multi-tasking real time operating system and a mixture of assembly and FORTRAN languages. The present collection of data sources produce data at widely varied rates and require varied amounts of burdensome real time processing and formatting. It was decided to replace the aging HP 21-MX minicomputer with a multiprocessor system. A new and flexible recording format was devised and implemented to accommodate the constantly changing sensor configuration. A central feature of this data system is the minimization of non-remote sensing bus traffic. Therefore, it is highly desirable that each micro be capable of functioning as much as possible on-card or via private peripherals. The bus is used primarily for the transfer of remote sensing data to or from the buffer queue.

Experience with a Genetic Algorithm Implemented on a Multiprocessor Computer

NASA Technical Reports Server (NTRS)

Plassman, Gerald E.; Sobieszczanski-Sobieski, Jaroslaw

2000-01-01

Numerical experiments were conducted to find out the extent to which a Genetic Algorithm (GA) may benefit from a multiprocessor implementation, considering, on one hand, that analyses of individual designs in a population are independent of each other so that they may be executed concurrently on separate processors, and, on the other hand, that there are some operations in a GA that cannot be so distributed. The algorithm experimented with was based on a gaussian distribution rather than bit exchange in the GA reproductive mechanism, and the test case was a hub frame structure of up to 1080 design variables. The experimentation engaging up to 128 processors confirmed expectations of radical elapsed time reductions comparing to a conventional single processor implementation. It also demonstrated that the time spent in the non-distributable parts of the algorithm and the attendant cross-processor communication may have a very detrimental effect on the efficient utilization of the multiprocessor machine and on the number of processors that can be used effectively in a concurrent manner. Three techniques were devised and tested to mitigate that effect, resulting in efficiency increasing to exceed 99 percent.

Atomistic scale nanoscratching behavior of monocrystalline Cu influenced by water film in CMP process

NASA Astrophysics Data System (ADS)

Shi, Junqin; Chen, Juan; Fang, Liang; Sun, Kun; Sun, Jiapeng; Han, Jing

2018-03-01

The effect of water film on the nanoscratching behavior of monocrystalline Cu was studied by molecular dynamics (MD) simulation. The results indicate that the friction force acting on abrasive particle increases due to the resistance of water film accumulating ahead of particle, but the water film with lubrication decreases friction force acting on Cu surface. The accumulation of water molecules around particle causes the anisotropy of ridge and the surface damage around the groove, and the water molecules remaining in the groove lead to the non-regular groove structure. The dislocation evolution displays the re-organization of the dislocation network in the nanoscratching process. The evaluation of removal efficiency shows the number of removed Cu atoms decreases with water film thickness. It is considered that an appropriate rather than a high removal efficiency should be adopted to evaluate the polishing process in real (chemical mechanical polishing) CMP. These results are helpful to reveal the polishing mechanism under the effect of water film from physical perspective, which benefits the development of ultra-precision manufacture and miniaturized components, as well as the innovation of CMP technology.

Note: Evaluation of slurry particle size analyzers for chemical mechanical planarization process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jang, Sunjae; Kulkarni, Atul; Qin, Hongyi

In the chemical mechanical planarization (CMP) process, slurry particle size is important because large particles can cause defects. Hence, selection of an appropriate particle measuring system is necessary in the CMP process. In this study, a scanning mobility particle sizer (SMPS) and dynamic light scattering (DLS) were compared for particle size distribution (PSD) measurements. In addition, the actual particle size and shape were confirmed by transmission electron microscope (TEM) results. SMPS classifies the particle size according to the electrical mobility, and measures the particle concentration (single particle measurement). On the other hand, the DLS measures the particle size distribution bymore » analyzing scattered light from multiple particles (multiple particle measurement). For the slurry particles selected for evaluation, it is observed that SMPS shows bi-modal particle sizes 30 nm and 80 nm, which closely matches with the TEM measurements, whereas DLS shows only single mode distribution in the range of 90 nm to 100 nm and showing incapability of measuring small particles. Hence, SMPS can be a better choice for the evaluation of CMP slurry particle size and concentration measurements.« less

Ultra-precision process of CaF2 single crystal

NASA Astrophysics Data System (ADS)

Yin, Guoju; Li, Shengyi; Xie, Xuhui; Zhou, Lin

2014-08-01

This paper proposes a new chemical mechanical polishing (CMP) process method for CaF2 single crystal to get ultraprecision surface. The CMP processes are improving polishing pad and using alkaline SiO2 polishing slurry with PH=8, PH=11 two phases to polish, respectively, and the roughness can be 0.181nm Rq (10μm×10μm). The CMP process can't get high surface figure, so we use ion beam figuring (IBF) technology to obtain high surface figure. However, IBF is difficult to improve the CaF2 surface roughness. We optimize IBF process to improve surface figure and keep good surface roughness too. Different IBF incident ion energy from 400ev to 800ev does not affect on the surface roughness obviously but the depth of material removal is reverse. CaF2 single crystal can get high precision surface figure (RMS=2.251nm) and still keep ultra-smooth surface (Rq=0.207nm) by IBF when removal depth is less than 200nm. The researches above provide important information for CaF2 single crystal to realize ultra-precision manufacture.

Metal Ion-Assembled Micro-Collagen Heterotrimers

PubMed Central

LeBruin, Lyndelle Toni; Banerjee, Sunandan; O'Rourke, Bruce Delany; Case, Martin Ashley

2011-01-01

Collagen mimetic peptides (CMPs) provide critical insight into the assembly, stability and structure of the triple helical collagen protein. The majority of natural fibrous collagens are aab or abc heterotrimers, yet few examples of heterotrimeric CMPs have been reported. Previously CMP heterotrimers have only been accessible by total syntheses or by introducing complementary interstrand electrostatic or steric interactions. Here we describe an abc CMP heterotrimer in which each contributing CMP consists of only three amino acids: glycine, proline and 4-hydroxyproline. Assembly of the heterotrimeric triple helix is directed by a combination of metal-ion coordination to set the relative register of the CMPs, and minimization of valence frustration to direct heterotrimerization. Assembly of the four-component mixture is facile and extremely rapid, and equilibration to the abc heterotrimer occurs within a few hours at modestly elevated temperatures. The melting temperatures of the metal-assembled collagen trimers are higher by some 30 °C than the apopeptide assemblies. Two iterations of the design are described, and the outcomes suggest possibilities for designing self-assembling abc and abb heterotrimers. PMID:21590759

Interaction of Tl +3 with mononucleotides: metal ion binding and sugar conformation

NASA Astrophysics Data System (ADS)

Nafisi, Sh.; Mohajerani, N.; Hadjiakhoondi, A.; Monajemi, M.; Garib, F.

2001-05-01

The interaction of Tl 3+ with sodium salts of adenosine-5'-monophosphate (5'-AMP), guanosine-5'-monophosphate (5'-GMP), cytidine-5'-monophosphate (5'-CMP), thymidine 5'-monophosphate (5'-dTMP) in ratios 1 and 2 have been studied in neutral pH. The solid complexes were isolated and characterized by Fourier transform infrared (FTIR) and 1H NMR spectroscopy. In the Tl 2(AMP) 3, Tl 3+ binds directly to N-7 and indirectly to the N-1 position of the pyrimidine ring and phosphate group with sugar moiety in C2'-endoanti. The crystalline salt of Tl 2(GMP) 3 show direct Tl-N-7 and Tl-PO 3(inner-sphere) binding. The conformation of ribose moiety in Tl 2(GMP) 3 is C3'-endoanti. In the Tl 2(CMP) 3, Tl 3+ bind directly to N-3 and PO32- (inner-sphere). The conformation of ribose moiety in Tl 2(CMP) 3 is C2'-endoanti. In the Tl 2(dTMP) 3, Tl 3+ bind indirectly to carbonyl group. The sugar moiety in Tl 2(dTMP) 3 is C3'-endoanti.

Identification of a novel ovine PrP polymorphism and scrapie-resistant genotypes for St. Croix White and a related composite breed.

PubMed

Seabury, C M; Derr, J N

2003-01-01

Susceptibility to scrapie is primarily controlled by polymorphisms in the ovine prion protein gene (PRNP). Here, we report a novel ovine exon three PRNP polymorphism (SNP G346C; P116), its association with the ovine ARQ allele (P116A136R154Q171), and two new genotypes (PARQ/ARR; PARQ/ARQ) for the St. Croix White (SCW) breed and a related composite (CMP) breed developed for meat production. The (P116) polymorphism occurs between the N-terminal cleavage site and the hydrophobic region of the ovine prion protein, a region which exhibits extreme conservation across mammalian taxa. The relatively high frequency (0.75) of resistant ARR alleles and the absence of ARQ alleles for the SCW ewes used as breeding stock for CMP resulted in significant genic differentiation (P = 0.0123; S.E. = 0.00113). Additionally, the majority of the SCW (66.7%) and CMP (65.4%) sampled possessed genotypes considered resistant or nearly resistant to scrapie and experimental BSE (bovine spongiform encephalopathy. Copyright 2003 S. Karger AG, Basel

Electro-Analytical Study of Material Interfaces Relevant for Chemical Mechanical Planarization and Lithium Ion Batteries

NASA Astrophysics Data System (ADS)

Turk, Michael C.

This dissertation work involves two areas of experimental research, focusing specifically on the applications of electro-analytical techniques for interfacial material characterization. The first area of the work is centered on the evaluation and characterization of material components used for chemical mechanical planarization (CMP) in the fabrication of semiconductor devices. This part also represents the bulk of the projects undertaken for the present dissertation. The other area of research included here involves exploratory electrochemical studies of certain electrolyte and electrode materials for applications in the development of advanced lithium ion secondary batteries. The common element between the two areas of investigation is the technical approach that combines a broad variety of electro-analytical characterization techniques to examine application specific functions of the associated materials and devices. The CMP related projects concentrate on designing and evaluating materials for CMP slurries that would be useful in the processing of copper interconnects for the sub-22 nm technology node. Specifically, ruthenium and cobalt are nontraditional barrier materials currently considered for the new interconnects. The CMP schemes used to process the structures based on these metals involve complex surface chemistries of Ru, Co and Cu (used for wiring lines). The strict requirement of defect-control while maintaining material removal by precisely regulated tribo-corrosion complicates the designs of the CMP slurries needed to process these systems. Since Ru is electrochemically more noble than Cu, the surface regions of Cu assembled in contact with Ru tend to generate defects due to galvanic corrosion in the CMP environment. At the same time, Co is strongly reactive in the typical slurry environment and is prone to developing galvanic corrosion induced by Cu. The present work explores a selected class of alkaline slurry formulations aimed at reducing these galvanic corrosions in chemically controlled low-pressure CMP. The CMP specific functions of the slurry components are characterized in the tribo-electro-analytical approach by using voltammetry, open circuit potential (OCP) measurements and electrochemical impedance spectroscopy (EIS) in the presence as well as in the absence of surface abrasion, both with and without the inclusion of colloidal silica (SiO2) abrasives. The results are used to understand the reaction mechanisms responsible for supporting material removal and corrosion suppression. The project carried out in the area of Li ion batteries (LIBs) uses electro-analytical techniques to probe electrolyte characteristics as well as electrode material performance. The investigation concentrates on optimizing a tactically chosen set of electrolyte compositions for low-to-moderate temperature applications of lithium titanium oxide (LTO), a relatively new anode material for such batteries. For this application, mixtures of non-aqueous carbonate based solvents are studied in combination with lithium perchlorate. The temperature dependent conductivities of the electrolytes are rigorously measured and analyzed using EIS. The experimental considerations and the working principle of this EIS based approach are carefully examined and standardized in the course of this study. These experiments also investigate the effects of temperature variations (below room temperature) on the solid electrolyte interphase (SEI) formation characteristics of LTO in the given electrolytes. This dissertation is organized as follows: Each experimental system and its relevance for practical applications are briefly introduced in each chapter. The experimental approach and the motivation for carrying out the investigation are also noted in that context. The experimental details specific to the particular study are described. This is followed by the results and their discussion, and subsequently, by the specific conclusions drawn from the given set of experiments. A general summary of the obtained results is presented at the end of the dissertation. Possible extensions of the present studies have also been briefly noted there.

Multitasking kernel for the C and Fortran programming languages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brooks, E.D. III

1984-09-01

A multitasking kernel for the C and Fortran programming languages which runs on the Unix operating system is presented. The kernel provides a multitasking environment which serves two purposes. The first is to provide an efficient portable environment for the coding, debugging and execution of production multiprocessor programs. The second is to provide a means of evaluating the performance of a multitasking program on model multiprocessors. The performance evaluation features require no changes in the source code of the application and are implemented as a set of compile and run time options in the kernel.

Distributed parallel messaging for multiprocessor systems

DOEpatents

Chen, Dong; Heidelberger, Philip; Salapura, Valentina; Senger, Robert M; Steinmacher-Burrow, Burhard; Sugawara, Yutaka

2013-06-04

A method and apparatus for distributed parallel messaging in a parallel computing system. The apparatus includes, at each node of a multiprocessor network, multiple injection messaging engine units and reception messaging engine units, each implementing a DMA engine and each supporting both multiple packet injection into and multiple reception from a network, in parallel. The reception side of the messaging unit (MU) includes a switch interface enabling writing of data of a packet received from the network to the memory system. The transmission side of the messaging unit, includes switch interface for reading from the memory system when injecting packets into the network.

Programming parallel architectures: The BLAZE family of languages

NASA Technical Reports Server (NTRS)

Mehrotra, Piyush

1988-01-01

Programming multiprocessor architectures is a critical research issue. An overview is given of the various approaches to programming these architectures that are currently being explored. It is argued that two of these approaches, interactive programming environments and functional parallel languages, are particularly attractive since they remove much of the burden of exploiting parallel architectures from the user. Also described is recent work by the author in the design of parallel languages. Research on languages for both shared and nonshared memory multiprocessors is described, as well as the relations of this work to other current language research projects.

Automatic Data Partitioning on Distributed Memory Multiprocessors

DTIC Science & Technology

1990-10-01

DISTRIBUTED MEMORY MULTIPROCESSORS D 1"’ 1 C . Manish Gupta NOV,1 41990.NOV 1 41990m Prithviraj Banerjee D Coordinated Science Laboratory College of...developed on the partitioning of arrays can as well be applied to other programming languages, such as C . 3 The rest of this paper is organized as follows...value 1, as in Fortran. a) N= 4, N 2 = 1: f(i) = J,(j) = 03 b) =Ni 1, N 2 =4: fA(i) =, f() - c ) NI 2, X) 2: f()=[., f2(j) = [L-.j d) N 1 , N 2 =4: fA(i

[Improving the CMP appointment waiting time for children and adolescents].

PubMed

Cani, Pascale

2014-01-01

The increasing activity of mental health centres for children and adolescents and longer waiting times in obtaining a first appointment have led an area of child psychiatry to question the organisation of new consultation applications. Two CMP in the sector had a waiting period of over 40 days for half of the patients. Two improvement actions were implemented:the implementation of organisation and reception nurses and the development of a new applications management process. The evaluation after one year showed a decrease of half of the appointment waiting time without changing the non showed up rate.

The Electronic CardioMetabolic Program (eCMP) for Patients With Cardiometabolic Risk: A Randomized Controlled Trial

PubMed Central

Koliwad, Suneil; Poon, Tak; Xiao, Lan; Lv, Nan; Griggs, Robert; Ma, Jun

2016-01-01

Background Effective lifestyle interventions targeting high-risk adults that are both practical for use in ambulatory care settings and scalable at a population management level are needed. Objective Our aim was to examine the potential effectiveness, feasibility, and acceptability of delivering an evidence-based Electronic Cardio-Metabolic Program (eCMP) for improving health-related quality of life, improving health behaviors, and reducing cardiometabolic risk factors in ambulatory care high-risk adults. Methods We conducted a randomized, wait-list controlled trial with 74 adults aged ≥18 years recruited from a large multispecialty health care organization. Inclusion criteria were (1) BMI ≥35 kg/m2 and prediabetes, previous gestational diabetes and/or metabolic syndrome, or (2) BMI ≥30 kg/m2 and type 2 diabetes and/or cardiovascular disease. Participants had a mean age of 59.7 years (SD 11.2), BMI 37.1 kg/m2 (SD 5.4) and were 59.5% female, 82.4% white. Participants were randomized to participate in eCMP immediately (n=37) or 3 months later (n=37). eCMP is a 6-month program utilizing video conferencing, online tools, and pre-recorded didactic videos to deliver evidence-based curricula. Blinded outcome assessments were conducted at 3 and 6 months postbaseline. Data were collected and analyzed between 2014 and 2015. The primary outcome was health-related quality of life. Secondary outcomes included biometric cardiometabolic risk factors (eg, body weight), self-reported diet and physical activity, mental health status, retention, session attendance, and participant satisfaction. Results Change in quality of life was not significant in both immediate and delayed participants. Both groups significantly lost weight and reduced waist circumference at 6 months, with some cardiometabolic factors trending accordingly. Significant reduction in self-reported anxiety and perceived stress was seen in the immediate intervention group at 6 months. Retention rate was 93% at 3 months and 86% at 6 months post-baseline. Overall eCMP attendance was high with 59.5-83.8% of immediate and delayed intervention participants attending 50% of the virtual stress management and behavioral lifestyle sessions and 37.8-62.2% attending at least 4 out of 7 in-person physical activity sessions. The intervention received high ratings for satisfaction. Conclusions The technology-assisted eCMP is a feasible and well-accepted intervention and may significantly decrease cardiometabolic risk among high-risk individuals. Trial Registration Clinicaltrials.gov NCT02246400; https://clinicaltrials.gov/ct2/show/NCT02246400 (Archived by WebCite at http://www.webcitation.org/6h6mWWokP) PMID:27234480

Material Characterization in the Electro-Analytic Approach for Applications in Chemical Mechanical Planarization and Electrochemical Energy Systems

NASA Astrophysics Data System (ADS)

Rock, Simon E.

The work presented in this thesis covers electro-analytical characterization for multiple applications in material science. Electrochemical techniques were used to investigate soluble film formation on metals used in chemical mechanical planarization in order to better understand the removal rate process by studying new chemicals proposed by groups in industry. Second, an ionic liquid was used as an electrolyte in a lithium ion cathode half cell to show the essential functionality of the IL and the temperature advantage over traditional electrolytes. Lastly, a comprehensive measurement for charge recombination in dye-sensitized solar cells was performed using both open-circuit voltage decay and impedance spectroscopy, which may be used to better understand the limiting factors that affect the cell's efficiently. Electrochemical techniques were applied to new methods and materials to extend the development of material manufacturing and advance the measurement process. The fabrication of interconnect structures for semiconductor devices requires low down-pressure chemical mechanical planarization (CMP) of Ta barrier layers. Guanidine carbonate (GC) serves as an effective surface-complexing agent for such CMP applications, where the rate of Ta removal can be chemically controlled through pH-tuned selectivity with respect to the removal of Cu lines. Electrochemical techniques are employed in this work to study the surface-modifying roles of GC that make this chemical an attractive complexing agent for Ta CMP. In addition, the effects of including H2O2 (an oxidizer) and dodecyl benzene sulfonic acid (DBSA, a dissolution inhibitor for Cu) in GC-based CMP solutions are investigated to examine the selective CMP mechanisms of Ta and Cu in these solutions. The results suggest that the removal of Ta is supported in part by structurally weak guanidinium-tantalic-acid surface complexes formed on Ta/Ta2O5. The bicarbonate/carbonate anions of GC also facilitate Ta removal through the generation of ion-incorporated tantalum pentoxide. DBSA strongly affects the CMP chemistry of Cu, but exhibits relatively weaker effects on the surface activity of Ta, and thus plays a vital role in dictating the selectivity of Ta:Cu polish rates. CMP of tantalum nitride is also an essential step of material processing in the fabrication of integrated circuits, which is looked separately in this thesis. The present work investigates certain chemical aspects of this strategy of TaN-CMP by also using guanidine carbonate (GC) as a surface complexing agent, and employing electrochemical experiments. The experiments are designed to study the chemical and electrochemical origins of the CMP-specific surface complex films formed on a TaN wafer in acidic solutions of GC and hydrogen peroxide. Open circuit potential, polarization resistance, and electrochemical impedance measurements are employed to probe the surface effects that facilitate material removal in chemically prevailing CMP of TaN. The results are discussed in view of designing slurry variables to support barrier layer planarization with reduced roles of mechanical abrasion. Nonvolatile and nonflammable ionic liquids (ILs) have distinct thermal advantages over the traditional organic solvent electrolytes of lithium ion batteries. However, this beneficial feature of ILs is often counterbalanced by their high viscosity (a limiting factor for ionic conductivity) and, sometimes, by their unsuitable electrochemistry for generating protective layers on electrode surfaces. In an effort to alleviate these limiting Aspects of ILs, we have synthesized a PEGylated imidazolium bis(triflouromethylsulfonyl)amide (bistriflamide) IL that exhibited better thermal and electrochemical stability than a conventional electrolyte based on a blend of ethylene carbonate and diethyl carbonate. The electrochemical performance of this IL has been demonstrated using a cathode consisting of ball-milled LiMn2O4 particles. A direct comparison of the ionic liquid electrolyte with the nonionic low-viscosity conventional solvent blend is presented. Charge recombination at the electrolyte-photoanode interface of a dye sensitized solar cell (DSSC) is a major efficiency-limiting factor of the cell. To mitigate this recombination effect it is necessary to ensure that the effective electron lifetime in the DSSC is longer than the electron's transit time across the photoanode of mesoporous TiO2. While the efforts aimed at accomplishing this goal are often based on new materials/designs of photoanodes, a quantitative evaluation of these designs relies on the precision of the benchmarking measurements of electron lifetimes. The open circuit voltage decay (OCVD) technique offers an effective yet straightforward method for such measurements. The present work focuses on certain experimental criteria for ensuring the accuracy of these experiments, and probes the associated effects of temperature variations in the solar cell. The results demonstrate that, a high rate of data sampling is essential for adequately resolving the fast initial stages of charge recombination. The results also show the effects of nonlinear recombination where second order OCV variations are operative. The findings of the OCVD experiments are compared with a parallel set of tests carried out using impedance spectroscopy. The relative roles of the two sets of analytical measurements are examined.

Clomipramine and Benznidazole Act Synergistically and Ameliorate the Outcome of Experimental Chagas Disease

PubMed Central

García, Mónica Cristina; Ponce, Nicolás Eric; Sanmarco, Liliana Maria; Manzo, Rubén Hilario; Jimenez-Kairuz, Alvaro Federico

2016-01-01

Chagas disease is an important public health problem in Latin America, and its treatment by chemotherapy with benznidazole (BZ) or nifurtimox remains unsatisfactory. In order to design new alternative strategies to improve the current etiological treatments, in the present work, we comprehensively evaluated the in vitro and in vivo anti-Trypanosoma cruzi effects of clomipramine (CMP) (a parasite-trypanothione reductase-specific inhibitor) combined with BZ. In vitro studies, carried out using a checkerboard technique on trypomastigotes (T. cruzi strain Tulahuen), revealed a combination index (CI) of 0.375, indicative of a synergistic effect of the drug combination. This result was correlated with the data obtained in infected BALB/c mice. We observed that during the acute phase (15 days postinfection [dpi]), BZ at 25 mg/kg of body weight/day alone decreased the levels of parasitemia compared with those of the control group, but when BZ was administered with CMP, the drug combination completely suppressed the parasitemia due to the observed synergistic effect. Furthermore, in the chronic phase (90 dpi), mice treated with both drugs showed less heart damage as assessed by the histopathological analysis, index of myocardial inflammation, and levels of heart injury biochemical markers than mice treated with BZ alone at the reference dose (100 mg/kg/day). Collectively, these data support the notion that CMP combined with low doses of BZ diminishes cardiac damage and inflammation during the chronic phase of cardiomyopathy. The synergistic activity of BZ-CMP clearly suggests a potential drug combination for Chagas disease treatment, which would allow a reduction of the effective dose of BZ and an increase in therapeutic safety. PMID:27067322

Chinese medicine patterns in patients with post-stroke dementia.

PubMed

Tang, Nou-Ying; Liu, Chung-Hsiang; Liu, Hsu-Jan; Li, Tsai-Chung; Liu, Jui-Chen; Chen, Ping-Kun; Hsieh, Ching-Liang

2012-04-01

A stroke often results in post-stroke dementia, a rapid decline in memory and intelligence causing dysfunctions in daily life. The Chinese medicine doctor uses 4 examinations of inspection, listening, smelling, and feeling to determine the Chinese medicine pattern (CMP). Therefore, the purpose of the present study was to investigate the CMP in patients with post-stroke dementia. A total of 101 stroke patients were examined, consistent with the DSM IV diagnostic criteria of the American Psychiatric Association, as well as the National Institute of Neurological Disorders and Stroke-Association International pour Ia Recherche et I'Enseignement en Neurosciences vascular dementia diagnostic criteria of post-stroke dementia. 100 patients (99.0%) were KEDP (kidney essence deficiency pattern, shèn jīng kuī xū zhèng, ), 83 patients were AHLYP (ascendant hyperactivity of liver yang pattern, gān yáng shàng kàng zhèng, ), 83 patients were QBDP (qi-blood deficiency pattern, qì xuè kuī xū zhèng, ), 81 patients were SBOCP (static blood obstructing the collaterals pattern, yū xuè zǔ luò zhèng, ), 72 patients were BSTRP (bowels stagnation turbidity retention pattern, fǔ zhì zhuó liú zhèng, ), 50 patients were FHIEP (fire heat interior excess pattern, huǒ rè nèi sheng zhèng, ), and 39 participants (38.6%) were PTOOP (phlegm turbidity obstructing the orifices pattern, tán zhuó zǔ qiào zhèng, ); one to 31 patients have at least 2 CMPs simultaneously. In conclusion, the most CMP is KEDP CMP in the post-stroke dementia patients, and one patient may have one or at least 2 CMPs simultaneously.

Implementing a hybrid approach to select patients for care management: variations across practices.

PubMed

Vogeli, Christine; Spirt, Jenna; Brand, Richard; Hsu, John; Mohta, Namita; Hong, Clemens; Weil, Eric; Ferris, Timothy G

2016-05-01

Appropriate selection of patients is key to the success of care management programs (CMPs). Hybrid patient selection approaches, in which large data assets are culled to develop a list of patients for more targeted clinical review, are increasingly common. We sought to describe the patient and practice characteristics associated with high-risk patient identification and selection for a CMP during clinical review, and to explore variation across primary care practices. Retrospective cohort study. Standardized estimates of Medicare beneficiaries identified as high risk for poor outcomes and high medical expense, and appropriate for a CMP within a large Pioneer Accountable Care Organization, were developed using mixed effects logistic models. Study subjects were 2685 Medicare beneficiaries aged over 18 (includes individuals eligible for Medicare due to a disability) aligned to 35 primary care practices in 2013. Independent predictors of patient identification as high risk include older age; higher risk score; recent increases in medical conditions; higher numbers of medical hospitalizations, skilled nursing facility days, and primary care physician visits; and shorter relationships with the primary care physician. Older age, and lower income, but no prior hospice use were independently associated with patient selection for a CMP among the subset of patients identified as being high risk. Adjusted predicted percents of high-risk patients varied significantly across practices overall and for 5 of the 6 patient characteristics that were independently associated with identification as high risk. Inconsistency in high-risk patient identification and selection for a CMP may reflect differences in practice resources, but also highlight the need for continual training and feedback in order to protect against unintentional biases.

Atmospheric oxidation of selected chlorinated alkenes by O3, OH, NO3 and Cl

NASA Astrophysics Data System (ADS)

Zhang, Qun; Chen, Yi; Tong, Shengrui; Ge, Maofa; Shenolikar, Justin; Johnson, Matthew S.; Wang, Yifeng; Tsona, Narcisse T.; Mellouki, Abdelwahid; Du, Lin

2017-12-01

An experimental study on the 3-chloro-2-methyl-1-propene (CMP), 2,3-dichloropropene (DCP) and 3,4-dichlorobutene (DCB) reactions with atmospheric oxidants at (298 ± 1) K and atmospheric pressure is reported. Rate constants for the gas phase reactions of the three chlorinated alkenes with O3, OH and NO3 radicals and Cl atom were determined in a 100 L Teflon reactor by gas chromatography with flame ionization detector (GC-FID). The obtained rate constants are (3.03 ± 0.15) × 10-18, (3.83 ± 1.30) × 10-11, (1.99 ± 0.19) × 10-14, and (2.40 ± 0.41) × 10-10 cm3 molecule-1 s-1 for CMP reactions with O3, OH, NO3, and Cl, respectively, (4.62 ± 1.41) × 10-20, (1.37 ± 1.02) × 10-11, (1.45 ± 0.15) × 10-15 and (1.30 ± 0.99) × 10-11 cm3 molecule-1 s-1 for DCP reactions and (2.09 ± 0.24) × 10-19, (1.45 ± 0.59) × 10-11, (3.00 ± 0.82) × 10-16 and (1.91 ± 0.19) × 10-10 cm3 molecule-1 s-1 for DCB reactions. The CMP reaction products were detected and possible reaction mechanisms of their formation were proposed. Chloroacetone was found to be the major product in all four oxidation reactions. The loss process of CMP in the atmosphere is mostly controlled by its reaction with the OH radical during daytime and with NO3 during nighttime, with lifetimes of 3.6 h and 27.9 h respectively. Atmospheric implications of both these reactions and their potential products are discussed.

Particulate emissions calculations from fall tillage operations using point and remote sensors.

PubMed

Moore, Kori D; Wojcik, Michael D; Martin, Randal S; Marchant, Christian C; Bingham, Gail E; Pfeiffer, Richard L; Prueger, John H; Hatfield, Jerry L

2013-07-01

Soil preparation for agricultural crops produces aerosols that may significantly contribute to seasonal atmospheric particulate matter (PM). Efforts to reduce PM emissions from tillage through a variety of conservation management practices (CMPs) have been made, but the reductions from many of these practices have not been measured in the field. A study was conducted in California's San Joaquin Valley to quantify emissions reductions from fall tillage CMP. Emissions were measured from conventional tillage methods and from a "combined operations" CMP, which combines several implements to reduce tractor passes. Measurements were made of soil moisture, bulk density, meteorological profiles, filter-based total suspended PM (TSP), concentrations of PM with an equivalent aerodynamic diameter ≤10 μm (PM) and PM with an equivalent aerodynamic diameter ≤2.5 μm (PM), and aerosol size distribution. A mass-calibrated, scanning, three-wavelength light detection and ranging (LIDAR) procedure estimated PM through a series of algorithms. Emissions were calculated via inverse modeling with mass concentration measurements and applying a mass balance to LIDAR data. Inverse modeling emission estimates were higher, often with statistically significant differences. Derived PM emissions for conventional operations generally agree with literature values. Sampling irregularities with a few filter-based samples prevented calculation of a complete set of emissions through inverse modeling; however, the LIDAR-based emissions dataset was complete. The CMP control effectiveness was calculated based on LIDAR-derived emissions to be 29 ± 2%, 60 ± 1%, and 25 ± 1% for PM, PM, and TSP size fractions, respectively. Implementation of this CMP provides an effective method for the reduction of PM emissions. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

ROLES OF ADIPOCYTES AND FIBROBLASTS IN ACTIVATION OF THE ALTERNATIVE PATHWAY OF COMPLEMENT IN INFLAMMATORY ARTHRITIS IN MICE

PubMed Central

Arend, William P.; Mehta, Gaurav; Antonioli, Alexandra H.; Takahashi, Minoru; Takahashi, Kazue; Stahl, Gregory L.; Holers, V. Michael; Banda, Nirmal K.

2013-01-01

The complement system is involved in mediation of joint damage in rheumatoid arthritis, with evidence suggesting activation of both the classical and alternative pathways (AP). The AP is both necessary and sufficient to mediate collagen antibody-induced arthritis (CAIA), an experimental animal model of immune complex (IC)-induced joint disease. The AP in mice is dependent on MASP-1/3 cleavage of pro-factor D (pro-FD) into mature FD. The objectives of the present study were to determine the cells synthesizing MASP-1/3 and pro-FD in synovial tissue. CAIA was studied in wild-type C57BL/6 mice, and the localization of mRNA and protein for FD and MASP-1/3 in synovial adipose tissue (SAT) and fibroblast-like synoviocytes (FLS) was determined using various techniques, including laser capture micro-dissection (LCM). SAT was the sole source of mRNA for pro-FD. Cultured differentiated 3T3 adipocytes, a surrogate for SAT, produced pro-FD but no mature FD. FLS were the main source of MASP-1/3 mRNA and protein. Using cartilage micro-particles (CMP) coated with anti-collagen mAb and serum from MASP-1/3−/− mice as a source of factor B, pro-FD in 3T3 supernatants was cleaved into mature FD by MASP-1/3 in FLS supernatants. The mature FD was eluted from the CMP, and was not present in the supernatants from the incubation with CMP, indicating that cleavage of pro-FD into mature FD by MASP-1 occurred on the CMP. These results demonstrate that pathogenic activation of the AP may occur in the joint through IC adherent to cartilage and the local production of necessary AP proteins by adipocytes and FLS. PMID:23650618

Self-reported work ability and work performance in workers with chronic nonspecific musculoskeletal pain.

PubMed

de Vries, Haitze J; Reneman, Michiel F; Groothoff, Johan W; Geertzen, Jan H B; Brouwer, Sandra

2013-03-01

To assess self-reported work ability and work performance of workers who stay at work despite chronic nonspecific musculoskeletal pain (CMP), and to explore which variables were associated with these outcomes. In a cross-sectional study we assessed work ability (Work Ability Index, single item scale 0-10) and work performance (Health and Work Performance Questionnaire, scale 0-10) among 119 workers who continued work while having CMP. Scores of work ability and work performance were categorized into excellent (10), good (9), moderate (8) and poor (0-7). Hierarchical multiple regression and logistic regression analysis was used to analyze the relation of socio-demographic, pain-related, personal- and work-related variables with work ability and work performance. Mean work ability and work performance were 7.1 and 7.7 (poor to moderate). Hierarchical multiple regression analysis revealed that higher work ability scores were associated with lower age, better general health perception, and higher pain self-efficacy beliefs (R(2) = 42 %). Higher work performance was associated with lower age, higher pain self-efficacy beliefs, lower physical work demand category and part-time work (R(2) = 37 %). Logistic regression analysis revealed that work ability ≥8 was significantly explained by age (OR = 0.90), general health perception (OR = 1.04) and pain self-efficacy (OR = 1.15). Work performance ≥8 was explained by pain self-efficacy (OR = 1.11). Many workers with CMP who stay at work report poor to moderate work ability and work performance. Our findings suggest that a subgroup of workers with CMP can stay at work with high work ability and performance, especially when they have high beliefs of pain self-efficacy. Our results further show that not the pain itself, but personal and work-related factors relate to work ability and work performance.

Enhanced efficacy of anticonvulsants when combined with levetiracetam in soman-exposed rats.

PubMed

Myhrer, Trond; Enger, Siri; Jonassen, Morten; Aas, Pål

2011-12-01

Results from studies based on microinfusions into seizure controlling brain sites (area tempestas, medial septum, perirhinal cortex, posterior piriform cortex) have shown that procyclidine, muscimol, caramiphen, and NBQX, but not ketamine, exert anticonvulsant effects against soman-induced seizures. The purpose of the present study was to examine whether levetiracetam (Keppra(®)) may enhance the anticonvulsant potency of the above drugs to become optimally effective when used systemically. Levetiracetam has a unique profile in preclinical models of epilepsy and has been shown to increase the potency of other antiepileptic drugs. The rats were pretreated with pyridostigmine (0.1mg/kg) to enhance survival and received anticonvulsants 20 min after onset of seizures evoked by soman (1.15 × LD(50)). The results showed that no single drug was able to terminate seizure activity. However, when levetiracetam (LEV; 50mg/kg) was combined with either procyclidine (PCD; 10mg/kg) or caramiphen (CMP; 10mg/kg) complete cessation of seizures was achieved, but the nicotinic antagonist mecamylamine was needed to induce full motor rest in some rats. In a subsequent experiment, rats were pretreated with HI-6 (125 mg/kg) to enhance survival and treatment started 40 min following seizure onset of a soman dose of 1.6 × LD(50). LEV (50mg/kg) combined with either PCD (20mg/kg) or CMP (20mg/kg) terminated seizure activity, but the survival rate was considerably higher for LEV+PCD than LEV+CMP. Both therapies could also save the lives of rats that were about to die 5-10 min after seizure onset. Thus, the combination of LEV and PCD or CMP may make up a model of a future autoinjector being effective regardless of the time of application. Copyright © 2011 Elsevier Inc. All rights reserved.

Clinical efficacy of EDTA ultrasonic activation in the reduction of endotoxins and cultivable bacteria.

PubMed

Herrera, D R; Martinho, F C; de-Jesus-Soares, A; Zaia, A A; Ferraz, C C R; Almeida, J F A; Gomes, B P F A

2017-10-01

This clinical study was conducted to investigate the influence of 17% ethylenediaminetetraacetic acid (EDTA) ultrasonic activation after chemomechanical preparation (CMP) on eliminating/reducing oral bacterial lipopolysaccharides (known as endotoxins) and cultivable bacteria in teeth with pulp necrosis and apical periodontitis. Samples were taken from 24 root canals at several clinical periods: S1 - before CMP; S2 - after CMP; S3 - after EDTA: G1 - with ultrasonic activation (n = 12) and G2 - without ultrasonic activation (n = 12). Root canals were instrumented using Mtwo rotary files. Culture techniques were used to determine the number of colony-forming units (CFU). Limulus amebocyte lysate (LAL) was used to measure endotoxin levels. Friedman's and Wilcoxon signed-rank tests were used to compare the amount of bacteria and endotoxin levels in each period (P < 0.05). Endotoxins and cultivable bacteria were recovered in 100% of the initial samples (S1). CMP was effective in reducing endotoxins and bacterial load (all with P < 0.05). Higher values of endotoxin reduction were achieved with EDTA ultrasonic activation [G1, 0.02 EU mL -1 (range 0.01-0.75)] compared with the no activation group [G2, 1.13 EU mL -1 (range 0.01-8.34)] (P < 0.05). Regarding bacterial reduction, no statistically significant difference was found in S3, regardless of the group (G1, G2, P > 0.05). Chemomechanical preparation was effective in reducing bacteria and endotoxins, but could not completely eliminate them. The ultrasonic activation of EDTA was effective in further reducing endotoxin levels in the root canals of teeth with pulp necrosis and apical periodontitis. © 2016 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Ternary borate-nucleoside complex stabilization by Ribonuclease A demonstrates phosphate mimicry

PubMed Central

Gabel, Scott A.; London, Robert E.

2010-01-01

Phosphate esters play a central role in cellular energetics, biochemical activation, signal transduction and conformational switching. The structural homology of the borate anion with phosphate, combined with its ability to spontaneously esterify hydroxyl groups, suggested that phosphate-ester recognition sites on proteins might exhibit significant affinity for non-enzymatically formed borate esters. 11B NMR studies and activity measurements on ribonuclease A in the presence of borate and several cytidine analogs demonstrate the formation of a stable ternary RNase A•3′-deoxycytidine-2′-borate ternary complex that mimics the complex formed between RNase A and a 2′-cytidine monophosphate (2′-CMP) inhibitor. Alternatively, no slowly exchanging borate resonance is observed for a ternary RNase A, borate, 2′-deoxycytidine mixture, demonstrating the critical importance of the 2′-hydroxyl group for complex formation. Titration of the ternary complex with 2′-CMP shows that it can displace the bound borate ester with a binding constant that is close to the reported inhibition constant of RNase A by 2′CMP. RNase A binding of a cyclic cytidine-2′,3′-borate ester, which is a structural homolog of the cytidine-2′,3′-cyclic phosphate substrate, could also be demonstrated. The apparent dissociation constant for the cytidine-2′,3′-borate•RNase A complex is 0.8 mM, which compares with a Michaelis constant of 11 mM for cCMP at pH 7, indicating considerably stronger binding. However, the value is 1000-fold larger than the reported dissociation constant of the RNase A complex with uridine-vanadate. These results are consistent with recent reports suggesting that in situ formation of borate esters that mimic the corresponding phosphate esters support enzyme catalysis. PMID:17957392

Deciding the liveness for a subclass of weighted Petri nets based on structurally circular wait

NASA Astrophysics Data System (ADS)

Liu, GuanJun; Chen, LiJing

2016-05-01

Weighted Petri nets as a kind of formal language are widely used to model and verify discrete event systems related to resource allocation like flexible manufacturing systems. System of Simple Sequential Processes with Multi-Resources (S3PMR, a subclass of weighted Petri nets and an important extension to the well-known System of Simple Sequential Processes with Resources, can model many discrete event systems in which (1) multiple processes may run in parallel and (2) each execution step of each process may use multiple units from multiple resource types. This paper gives a necessary and sufficient condition for the liveness of S3PMR. A new structural concept called Structurally Circular Wait (SCW) is proposed for S3PMR. Blocking Marking (BM) associated with an SCW is defined. It is proven that a marked S3PMR is live if and only if each SCW has no BM. We use an example of multi-processor system-on-chip to show that SCW and BM can precisely characterise the (partial) deadlocks for S3PMR. Simultaneously, two examples are used to show the advantages of SCW in preventing deadlocks of S3PMR. These results are significant for the further research on dealing with the deadlock problem.

Low energy CMOS for space applications

NASA Technical Reports Server (NTRS)

Panwar, Ramesh; Alkalaj, Leon

1992-01-01

The current focus of NASA's space flight programs reflects a new thrust towards smaller, less costly, and more frequent space missions, when compared to missions such as Galileo, Magellan, or Cassini. Recently, the concept of a microspacecraft was proposed. In this concept, a small, compact spacecraft that weighs tens of kilograms performs focused scientific objectives such as imaging. Similarly, a Mars Lander micro-rover project is under study that will allow miniature robots weighing less than seven kilograms to explore the Martian surface. To bring the microspacecraft and microrover ideas to fruition, one will have to leverage compact 3D multi-chip module-based multiprocessors (MCM) technologies. Low energy CMOS will become increasingly important because of the thermodynamic considerations in cooling compact 3D MCM implementations and also from considerations of the power budget for space applications. In this paper, we show how the operating voltage is related to the threshold voltage of the CMOS transistors for accomplishing a task in VLSI with minimal energy. We also derive expressions for the noise margins at the optimal operating point. We then look at a low voltage CMOS (LVCMOS) technology developed at Stanford University which improves the power consumption over conventional CMOS by a couple of orders of magnitude and consider the suitability of the technology for space applications by characterizing its SEU immunity.

Multiprocessor and memory architecture of the neurocomputer SYNAPSE-1.

PubMed

Ramacher, U; Raab, W; Anlauf, J; Hachmann, U; Beichter, J; Brüls, N; Wesseling, M; Sicheneder, E; Männer, R; Glass, J

1993-12-01

A general purpose neurocomputer, SYNAPSE-1, which exhibits a multiprocessor and memory architecture is presented. It offers wide flexibility with respect to neural algorithms and a speed-up factor of several orders of magnitude--including learning. The computational power is provided by a 2-dimensional systolic array of neural signal processors. Since the weights are stored outside these NSPs, memory size and processing power can be adapted individually to the application needs. A neural algorithms programming language, embedded in C(+2) has been defined for the user to cope with the neurocomputer. In a benchmark test, the prototype of SYNAPSE-1 was 8000 times as fast as a standard workstation.

An efficient 3-dim FFT for plane wave electronic structure calculations on massively parallel machines composed of multiprocessor nodes

NASA Astrophysics Data System (ADS)

Goedecker, Stefan; Boulet, Mireille; Deutsch, Thierry

2003-08-01

Three-dimensional Fast Fourier Transforms (FFTs) are the main computational task in plane wave electronic structure calculations. Obtaining a high performance on a large numbers of processors is non-trivial on the latest generation of parallel computers that consist of nodes made up of a shared memory multiprocessors. A non-dogmatic method for obtaining high performance for such 3-dim FFTs in a combined MPI/OpenMP programming paradigm will be presented. Exploiting the peculiarities of plane wave electronic structure calculations, speedups of up to 160 and speeds of up to 130 Gflops were obtained on 256 processors.

Automatic partitioning of unstructured meshes for the parallel solution of problems in computational mechanics

NASA Technical Reports Server (NTRS)

Farhat, Charbel; Lesoinne, Michel

1993-01-01

Most of the recently proposed computational methods for solving partial differential equations on multiprocessor architectures stem from the 'divide and conquer' paradigm and involve some form of domain decomposition. For those methods which also require grids of points or patches of elements, it is often necessary to explicitly partition the underlying mesh, especially when working with local memory parallel processors. In this paper, a family of cost-effective algorithms for the automatic partitioning of arbitrary two- and three-dimensional finite element and finite difference meshes is presented and discussed in view of a domain decomposed solution procedure and parallel processing. The influence of the algorithmic aspects of a solution method (implicit/explicit computations), and the architectural specifics of a multiprocessor (SIMD/MIMD, startup/transmission time), on the design of a mesh partitioning algorithm are discussed. The impact of the partitioning strategy on load balancing, operation count, operator conditioning, rate of convergence and processor mapping is also addressed. Finally, the proposed mesh decomposition algorithms are demonstrated with realistic examples of finite element, finite volume, and finite difference meshes associated with the parallel solution of solid and fluid mechanics problems on the iPSC/2 and iPSC/860 multiprocessors.

Parallel processing of real-time dynamic systems simulation on OSCAR (Optimally SCheduled Advanced multiprocessoR)

NASA Technical Reports Server (NTRS)

Kasahara, Hironori; Honda, Hiroki; Narita, Seinosuke

1989-01-01

Parallel processing of real-time dynamic systems simulation on a multiprocessor system named OSCAR is presented. In the simulation of dynamic systems, generally, the same calculation are repeated every time step. However, we cannot apply to Do-all or the Do-across techniques for parallel processing of the simulation since there exist data dependencies from the end of an iteration to the beginning of the next iteration and furthermore data-input and data-output are required every sampling time period. Therefore, parallelism inside the calculation required for a single time step, or a large basic block which consists of arithmetic assignment statements, must be used. In the proposed method, near fine grain tasks, each of which consists of one or more floating point operations, are generated to extract the parallelism from the calculation and assigned to processors by using optimal static scheduling at compile time in order to reduce large run time overhead caused by the use of near fine grain tasks. The practicality of the scheme is demonstrated on OSCAR (Optimally SCheduled Advanced multiprocessoR) which has been developed to extract advantageous features of static scheduling algorithms to the maximum extent.

Scalable Multiprocessor for High-Speed Computing in Space

NASA Technical Reports Server (NTRS)

Lux, James; Lang, Minh; Nishimoto, Kouji; Clark, Douglas; Stosic, Dorothy; Bachmann, Alex; Wilkinson, William; Steffke, Richard

2004-01-01

A report discusses the continuing development of a scalable multiprocessor computing system for hard real-time applications aboard a spacecraft. "Hard realtime applications" signifies applications, like real-time radar signal processing, in which the data to be processed are generated at "hundreds" of pulses per second, each pulse "requiring" millions of arithmetic operations. In these applications, the digital processors must be tightly integrated with analog instrumentation (e.g., radar equipment), and data input/output must be synchronized with analog instrumentation, controlled to within fractions of a microsecond. The scalable multiprocessor is a cluster of identical commercial-off-the-shelf generic DSP (digital-signal-processing) computers plus generic interface circuits, including analog-to-digital converters, all controlled by software. The processors are computers interconnected by high-speed serial links. Performance can be increased by adding hardware modules and correspondingly modifying the software. Work is distributed among the processors in a parallel or pipeline fashion by means of a flexible master/slave control and timing scheme. Each processor operates under its own local clock; synchronization is achieved by broadcasting master time signals to all the processors, which compute offsets between the master clock and their local clocks.

Process Management and Exception Handling in Multiprocessor Operating Systems Using Object-Oriented Design Techniques. Revised Sep. 1988

NASA Technical Reports Server (NTRS)

Russo, Vincent; Johnston, Gary; Campbell, Roy

1988-01-01

The programming of the interrupt handling mechanisms, process switching primitives, scheduling mechanism, and synchronization primitives of an operating system for a multiprocessor require both efficient code in order to support the needs of high- performance or real-time applications and careful organization to facilitate maintenance. Although many advantages have been claimed for object-oriented class hierarchical languages and their corresponding design methodologies, the application of these techniques to the design of the primitives within an operating system has not been widely demonstrated. To investigate the role of class hierarchical design in systems programming, the authors have constructed the Choices multiprocessor operating system architecture the C++ programming language. During the implementation, it was found that many operating system design concerns can be represented advantageously using a class hierarchical approach, including: the separation of mechanism and policy; the organization of an operating system into layers, each of which represents an abstract machine; and the notions of process and exception management. In this paper, we discuss an implementation of the low-level primitives of this system and outline the strategy by which we developed our solution.

Method for prefetching non-contiguous data structures

DOEpatents

Blumrich, Matthias A [Ridgefield, CT; Chen, Dong [Croton On Hudson, NY; Coteus, Paul W [Yorktown Heights, NY; Gara, Alan G [Mount Kisco, NY; Giampapa, Mark E [Irvington, NY; Heidelberger, Philip [Cortlandt Manor, NY; Hoenicke, Dirk [Ossining, NY; Ohmacht, Martin [Brewster, NY; Steinmacher-Burow, Burkhard D [Mount Kisco, NY; Takken, Todd E [Mount Kisco, NY; Vranas, Pavlos M [Bedford Hills, NY

2009-05-05

A low latency memory system access is provided in association with a weakly-ordered multiprocessor system. Each processor in the multiprocessor shares resources, and each shared resource has an associated lock within a locking device that provides support for synchronization between the multiple processors in the multiprocessor and the orderly sharing of the resources. A processor only has permission to access a resource when it owns the lock associated with that resource, and an attempt by a processor to own a lock requires only a single load operation, rather than a traditional atomic load followed by store, such that the processor only performs a read operation and the hardware locking device performs a subsequent write operation rather than the processor. A simple perfecting for non-contiguous data structures is also disclosed. A memory line is redefined so that in addition to the normal physical memory data, every line includes a pointer that is large enough to point to any other line in the memory, wherein the pointers to determine which memory line to prefect rather than some other predictive algorithm. This enables hardware to effectively prefect memory access patterns that are non-contiguous, but repetitive.

Low latency memory access and synchronization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blumrich, Matthias A.; Chen, Dong; Coteus, Paul W.

A low latency memory system access is provided in association with a weakly-ordered multiprocessor system. Each processor in the multiprocessor shares resources, and each shared resource has an associated lock within a locking device that provides support for synchronization between the multiple processors in the multiprocessor and the orderly sharing of the resources. A processor only has permission to access a resource when it owns the lock associated with that resource, and an attempt by a processor to own a lock requires only a single load operation, rather than a traditional atomic load followed by store, such that the processormore » only performs a read operation and the hardware locking device performs a subsequent write operation rather than the processor. A simple prefetching for non-contiguous data structures is also disclosed. A memory line is redefined so that in addition to the normal physical memory data, every line includes a pointer that is large enough to point to any other line in the memory, wherein the pointers to determine which memory line to prefetch rather than some other predictive algorithm. This enables hardware to effectively prefetch memory access patterns that are non-contiguous, but repetitive.« less

Low latency memory access and synchronization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blumrich, Matthias A.; Chen, Dong; Coteus, Paul W.

A low latency memory system access is provided in association with a weakly-ordered multiprocessor system. Bach processor in the multiprocessor shares resources, and each shared resource has an associated lock within a locking device that provides support for synchronization between the multiple processors in the multiprocessor and the orderly sharing of the resources. A processor only has permission to access a resource when it owns the lock associated with that resource, and an attempt by a processor to own a lock requires only a single load operation, rather than a traditional atomic load followed by store, such that the processormore » only performs a read operation and the hardware locking device performs a subsequent write operation rather than the processor. A simple prefetching for non-contiguous data structures is also disclosed. A memory line is redefined so that in addition to the normal physical memory data, every line includes a pointer that is large enough to point to any other line in the memory, wherein the pointers to determine which memory line to prefetch rather than some other predictive algorithm. This enables hardware to effectively prefetch memory access patterns that are non-contiguous, but repetitive.« less

Energy-efficient fault tolerance in multiprocessor real-time systems

NASA Astrophysics Data System (ADS)

Guo, Yifeng

The recent progress in the multiprocessor/multicore systems has important implications for real-time system design and operation. From vehicle navigation to space applications as well as industrial control systems, the trend is to deploy multiple processors in real-time systems: systems with 4 -- 8 processors are common, and it is expected that many-core systems with dozens of processing cores will be available in near future. For such systems, in addition to general temporal requirement common for all real-time systems, two additional operational objectives are seen as critical: energy efficiency and fault tolerance. An intriguing dimension of the problem is that energy efficiency and fault tolerance are typically conflicting objectives, due to the fact that tolerating faults (e.g., permanent/transient) often requires extra resources with high energy consumption potential. In this dissertation, various techniques for energy-efficient fault tolerance in multiprocessor real-time systems have been investigated. First, the Reliability-Aware Power Management (RAPM) framework, which can preserve the system reliability with respect to transient faults when Dynamic Voltage Scaling (DVS) is applied for energy savings, is extended to support parallel real-time applications with precedence constraints. Next, the traditional Standby-Sparing (SS) technique for dual processor systems, which takes both transient and permanent faults into consideration while saving energy, is generalized to support multiprocessor systems with arbitrary number of identical processors. Observing the inefficient usage of slack time in the SS technique, a Preference-Oriented Scheduling Framework is designed to address the problem where tasks are given preferences for being executed as soon as possible (ASAP) or as late as possible (ALAP). A preference-oriented earliest deadline (POED) scheduler is proposed and its application in multiprocessor systems for energy-efficient fault tolerance is investigated, where tasks' main copies are executed ASAP while backup copies ALAP to reduce the overlapped execution of main and backup copies of the same task and thus reduce energy consumption. All proposed techniques are evaluated through extensive simulations and compared with other state-of-the-art approaches. The simulation results confirm that the proposed schemes can preserve the system reliability while still achieving substantial energy savings. Finally, for both SS and POED based Energy-Efficient Fault-Tolerant (EEFT) schemes, a series of recovery strategies are designed when more than one (transient and permanent) faults need to be tolerated.

Chromatic multifocal pupillometer for objective early diagnosis of mild cognitive impairment

NASA Astrophysics Data System (ADS)

Rotenstreich, Ygal; Ben-Ner, Daniel; Sharvit-Ginon, Inbal; Ravona-Springer, Ramit; Beeri, Michal; Sher, Ifat

2017-02-01

The pupil responses of 15 cognitively normal subjects (ages 60-74) were examined in response to 76 focal red and blue light stimuli using a chromatic multifocal pupillometer (CMP). Subjects with low cognitive scores as determined as by Montreal Cognitive Assessment testing, presented significantly weaker and sluggish pupil responses in peripheral and central locations of the visual field in response to red and blue light. Our findings suggests that the CMP may present a novel objective, non-invasive, low cost technique for early diagnosis of cognitive decline that may serve for Alzheimer Disease prevention and as sensitive outcome measure of therapeutic effects.

Micro Computer Feedback Report for the Strategic Leader Development Inventory

DTIC Science & Technology

1993-05-01

POS or NEG variables CALL CREATE MEM DIR ;make a memory directory JC SELS ;exat I error CALL SELECT-SCREEN ;dlsplay select screen JC SEL4 ;no flles in...get keyboaI Input CMP AL,1Bh3 ;ls I an Esc key ? JNZ SEL2 ;X not goto nrod test G-95 JMP SEL4 ;Exit SEL2: CMP AL,OOh Iskapick? JZ SEL ;I YES exit loop...position CALL READ DATE ;gat DOS daoe od 4e CALL F4ND -ERO ;kxlae OW In data ue JC SEL.5 SEL4 : CALL RELEASE MEM DIR ;release meu block CLC ;cler carry fag

Mechanism of the development of a weakly alkaline barrier slurry without BTA and oxidizer

NASA Astrophysics Data System (ADS)

Xiaodong, Luan; Yuling, Liu; Xinhuan, Niu; Juan, Wang

2015-07-01

Controllable removal rate selectivity with various films (Cu, Ta, SiO2) is a challenging job in barrier CMP. H2O2 as an oxidizer and benzotriazole (BTA) as an inhibitor is considered to be an effective method in barrier CMP. Slurries that contain hydrogen peroxide have a very short shelf life because H2O2 is unstable and easily decomposed. BTA can cause post-CMP challenges, such as organic residue, toxicity and particle adhesion. We have been engaged in studying a weakly alkaline barrier slurry without oxidizer and benzotriazole. Based on these works, the objective of this paper is to discuss the mechanism of the development of the barrier slurry without oxidizer and benzotriazole by studying the effects of the different components (containing colloidal silica, FA/O complexing agent, pH of polishing solution and guanidine nitrate) on removal rate selectivity. The possible related polishing mechanism has also been proposed. Project supported by the Major National Science and Technology Special Projects (No. 2009ZX02308), the National Natural Science Foundation of Hebei Province, China (No. E2013202247), and the Department of Education-Funded Research Projects of Hebei Province, China (No. QN2014208).

Relation between isokinetic muscle strength and functional capacity in recreational athletes with chondromalacia patellae.

PubMed

Yildiz, Y; Aydin, T; Sekir, U; Cetin, C; Ors, F; Alp Kalyon, T

2003-12-01

To investigate the effects of isokinetic exercise on pain and functional test scores of recreational athletes with chondromalacia patellae (CMP) and to examine the correlation between isokinetic parameters and functional tests or pain score. The functional ability of 30 recreational athletes with unilateral CMP was evaluated using six different tests. Pain scores were assessed during daily activities before and after the treatment protocol. Isokinetic exercise sessions were carried out at angular velocities of 60 degrees /s (25-90 degrees range of flexion) and 180 degrees /s (full range). These sessions were repeated three times a week for six weeks. Quadriceps and hamstring peak torque, total work, and endurance ratios had improved significantly after the treatment, as did the functional parameters and pain scores. There was a poor correlation between the extensor endurance ratio and one leg standing test. A moderate correlation between the visual analogue scale and the extensor endurance ratio or flexion endurance ratio was also found. The isokinetic exercise programme used in this study had a positive effect on muscle strength, pain score, and functional ability of knees with CMP. The improvement in the functional capacity did not correlate with the isokinetic parameters.

Genomic and molecular analysis of phage CMP1 from Clavibacter michiganensis subspecies michiganensis

PubMed Central

Wittmann, Johannes; Gartemann, Karl-Heinz; Eichenlaub, Rudolf

2011-01-01

Bacteriophage CMP1 is a member of the Siphoviridae family that infects specifically the plant-pathogen Clavibacter michiganensis subsp. michiganensis. The linear double- stranded DNA is terminally redundant and not circularly permuted. The complete nucleotide sequence of the bacteriophage CMP1 genome consists of 58,652 bp including the terminal redundant ends of 791 bp. The G+C content of the phage (57%) is significantly lower than that of its host (72.66%). 74 potential open reading frames were identified and annotated by different bioinformatic tools. Two large clusters which encode the early and the late functions could be identified which are divergently transcribed. There are only a few hypothetical gene products with conserved domains and significant similarity to sequences from the databases. Functional analyses confirmed the activity of four gene products, an endonuclease, an exonuclease, a single-stranded DNA binding protein and a thymidylate synthase. Partial genomic sequences of CN77, a phage of Clavibacter michiganensis subsp. nebraskensis, revealed a similar genome structure and significant similarities on the level of deduced amino acid sequences. An endolysin with peptidase activity has been identified for both phages, which may be good tools for disease control of tomato plants against Clavibacter infections. PMID:21687530

Genomic and molecular analysis of phage CMP1 from Clavibacter michiganensis subspecies michiganensis.

PubMed

Wittmann, Johannes; Gartemann, Karl-Heinz; Eichenlaub, Rudolf; Dreiseikelmann, Brigitte

2011-01-01

Bacteriophage CMP1 is a member of the Siphoviridae family that infects specifically the plant-pathogen Clavibacter michiganensis subsp. michiganensis. The linear double- stranded DNA is terminally redundant and not circularly permuted. The complete nucleotide sequence of the bacteriophage CMP1 genome consists of 58,652 bp including the terminal redundant ends of 791 bp. The G+C content of the phage (57%) is significantly lower than that of its host (72.66%). 74 potential open reading frames were identified and annotated by different bioinformatic tools. Two large clusters which encode the early and the late functions could be identified which are divergently transcribed. There are only a few hypothetical gene products with conserved domains and significant similarity to sequences from the databases. Functional analyses confirmed the activity of four gene products, an endonuclease, an exonuclease, a single-stranded DNA binding protein and a thymidylate synthase. Partial genomic sequences of CN77, a phage of Clavibacter michiganensis subsp. nebraskensis, revealed a similar genome structure and significant similarities on the level of deduced amino acid sequences. An endolysin with peptidase activity has been identified for both phages, which may be good tools for disease control of tomato plants against Clavibacter infections.

Impact of a Traditional Dietary Supplement with Coconut Milk and Soya Milk on the Lipid Profile in Normal Free Living Subjects

PubMed Central

Ekanayaka, R. A. I.; Ekanayaka, N. K.; Perera, B.; De Silva, P. G. S. M.

2013-01-01

Background. The effects of coconut fat and soya fat on serum lipids are controversial. This study was designed to investigate the lipid effects of coconut milk and soya milk supplementation on the lipid profile of free living healthy subjects. Methods. Sixty (60) healthy volunteers aged 18–57 years were given coconut milk porridge (CMP) for 5 days of the week for 8 weeks, followed by a 2-week washout period, subsequent to which they received isoenergetic soya milk porridge (SMP) for 8 weeks. Results. The LDL (low density lipoprotein) levels decreased with CMP and reached statistical significance in the total study population and in the >130 baseline LDL group. The HDL (high density lipoprotein) levels rose significantly with CMP supplementation (P = 0.000). Conclusions. We conclude that coconut fat in the form of CM does not cause a detrimental effect on the lipid profile in the general population and in fact is beneficial due to the decrease in LDL and rise in HDL. SMP will be of benefit only in those whose baseline LDL levels are elevated. PMID:24282632

Deoxyribonucleic Acid Replication and Expression of Early and Late Bacteriophage Functions in Bacillus subtilis

PubMed Central

Pène, Jacques J.; Marmur, Julius

1967-01-01

The role of deoxyribonucleic acid (DNA) replication in the control of the synthesis of deoxycytidylate (dCMP) deaminase and lysozyme in Bacillus subtilis infected with bacteriophage 2C has been studied. These phage-induced enzymes are synthesized at different times during the latent period. It was shown by actinomycin inhibition that the formation of the late enzyme (lysozyme) required messenger ribonucleic acid (mRNA) synthesized de novo after the initiation of translation of mRNA which specifies the early function (dCMP deaminase). The inhibition of phage DNA synthesis by mitomycin C prevented the synthesis of lysozyme only when added before the onset of phage DNA replication, but it did not affect the synthesis or action of dCMP deaminase when added at any time during the latent period. Treatment of infected cells with mitomycin C after phage DNA synthesis had reached 8 to 10% of its maximal rate resulted in the production of normal amounts of lysozyme. These observations suggest that mRNA specifying early enzymes can be transcribed from parental (and probably also from progeny) DNA, whereas late functional messengers can be transcribed only after the formation of progeny DNA. PMID:4990039

Adsorption treatment of oxide chemical mechanical polishing wastewater from a semiconductor manufacturing plant by electrocoagulation.

PubMed

Chou, Wei-Lung; Wang, Chih-Ta; Chang, Wen-Chun; Chang, Shih-Yu

2010-08-15

In this study, metal hydroxides generated during electrocoagulation (EC) were used to remove the chemical oxygen demand (COD) of oxide chemical mechanical polishing (oxide-CMP) wastewater from a semiconductor manufacturing plant by EC. Adsorption studies were conducted in a batch system for various current densities and temperatures. The COD concentration in the oxide-CMP wastewater was effectively removed and decreased by more than 90%, resulting in a final wastewater COD concentration that was below the Taiwan discharge standard (100 mg L(-1)). Since the processed wastewater quality exceeded the direct discharge standard, the effluent could be considered for reuse. The adsorption kinetic studies showed that the EC process was best described using the pseudo-second-order kinetic model at the various current densities and temperatures. The experimental data were also tested against different adsorption isotherm models to describe the EC process. The Freundlich adsorption isotherm model predictions matched satisfactorily with the experimental observations. Thermodynamic parameters, including the Gibbs free energy, enthalpy, and entropy, indicated that the COD adsorption of oxide-CMP wastewater on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K. Copyright 2010 Elsevier B.V. All rights reserved.

Performance issues for domain-oriented time-driven distributed simulations

NASA Technical Reports Server (NTRS)

Nicol, David M.

1987-01-01

It has long been recognized that simulations form an interesting and important class of computations that may benefit from distributed or parallel processing. Since the point of parallel processing is improved performance, the recent proliferation of multiprocessors requires that we consider the performance issues that naturally arise when attempting to implement a distributed simulation. Three such issues are: (1) the problem of mapping the simulation onto the architecture, (2) the possibilities for performing redundant computation in order to reduce communication, and (3) the avoidance of deadlock due to distributed contention for message-buffer space. These issues are discussed in the context of a battlefield simulation implemented on a medium-scale multiprocessor message-passing architecture.

MPF: A portable message passing facility for shared memory multiprocessors

NASA Technical Reports Server (NTRS)

Malony, Allen D.; Reed, Daniel A.; Mcguire, Patrick J.

1987-01-01

The design, implementation, and performance evaluation of a message passing facility (MPF) for shared memory multiprocessors are presented. The MPF is based on a message passing model conceptually similar to conversations. Participants (parallel processors) can enter or leave a conversation at any time. The message passing primitives for this model are implemented as a portable library of C function calls. The MPF is currently operational on a Sequent Balance 21000, and several parallel applications were developed and tested. Several simple benchmark programs are presented to establish interprocess communication performance for common patterns of interprocess communication. Finally, performance figures are presented for two parallel applications, linear systems solution, and iterative solution of partial differential equations.

Partitioning and packing mathematical simulation models for calculation on parallel computers

NASA Technical Reports Server (NTRS)

Arpasi, D. J.; Milner, E. J.

1986-01-01

The development of multiprocessor simulations from a serial set of ordinary differential equations describing a physical system is described. Degrees of parallelism (i.e., coupling between the equations) and their impact on parallel processing are discussed. The problem of identifying computational parallelism within sets of closely coupled equations that require the exchange of current values of variables is described. A technique is presented for identifying this parallelism and for partitioning the equations for parallel solution on a multiprocessor. An algorithm which packs the equations into a minimum number of processors is also described. The results of the packing algorithm when applied to a turbojet engine model are presented in terms of processor utilization.

Event parallelism: Distributed memory parallel computing for high energy physics experiments

NASA Astrophysics Data System (ADS)

Nash, Thomas

1989-12-01

This paper describes the present and expected future development of distributed memory parallel computers for high energy physics experiments. It covers the use of event parallel microprocessor farms, particularly at Fermilab, including both ACP multiprocessors and farms of MicroVAXES. These systems have proven very cost effective in the past. A case is made for moving to the more open environment of UNIX and RISC processors. The 2nd Generation ACP Multiprocessor System, which is based on powerful RISC system, is described. Given the promise of still more extraordinary increases in processor performance, a new emphasis on point to point, rather than bussed, communication will be required. Developments in this direction are described.

A multiarchitecture parallel-processing development environment

NASA Technical Reports Server (NTRS)

Townsend, Scott; Blech, Richard; Cole, Gary

1993-01-01

A description is given of the hardware and software of a multiprocessor test bed - the second generation Hypercluster system. The Hypercluster architecture consists of a standard hypercube distributed-memory topology, with multiprocessor shared-memory nodes. By using standard, off-the-shelf hardware, the system can be upgraded to use rapidly improving computer technology. The Hypercluster's multiarchitecture nature makes it suitable for researching parallel algorithms in computational field simulation applications (e.g., computational fluid dynamics). The dedicated test-bed environment of the Hypercluster and its custom-built software allows experiments with various parallel-processing concepts such as message passing algorithms, debugging tools, and computational 'steering'. Such research would be difficult, if not impossible, to achieve on shared, commercial systems.

Development and evaluation of a fault-tolerant multiprocessor (FTMP) computer. Volume 4: FTMP executive summary

NASA Technical Reports Server (NTRS)

Smith, T. B., III; Lala, J. H.

1984-01-01

The FTMP architecture is a high reliability computer concept modeled after a homogeneous multiprocessor architecture. Elements of the FTMP are operated in tight synchronism with one another and hardware fault-detection and fault-masking is provided which is transparent to the software. Operating system design and user software design is thus greatly simplified. Performance of the FTMP is also comparable to that of a simplex equivalent due to the efficiency of fault handling hardware. The FTMP project constructed an engineering module of the FTMP, programmed the machine and extensively tested the architecture through fault injection and other stress testing. This testing confirmed the soundness of the FTMP concepts.

A measurement-based performability model for a multiprocessor system

NASA Technical Reports Server (NTRS)

Ilsueh, M. C.; Iyer, Ravi K.; Trivedi, K. S.

1987-01-01

A measurement-based performability model based on real error-data collected on a multiprocessor system is described. Model development from the raw errror-data to the estimation of cumulative reward is described. Both normal and failure behavior of the system are characterized. The measured data show that the holding times in key operational and failure states are not simple exponential and that semi-Markov process is necessary to model the system behavior. A reward function, based on the service rate and the error rate in each state, is then defined in order to estimate the performability of the system and to depict the cost of different failure types and recovery procedures.

Effect of magnetization boundary condition on cavity magnon polariton of YIG thin film.

PubMed

Jiang, H H; Xiao, Y; Hu, C M; Guo, H; Xia, K

2018-06-22

Motivated by recent studies of cavity magnon polariton (CMP), we extended a previous theoretical work to generalize microwave transmission calculation with various magnetization boundary condition of YIG thin film embedded in cavity. It is found that numerical implementation given in this paper can be easily applied to other magnetization boundary condition and extended to magnetic multilayers. Numerical results show that ferromagnetic resonance mode of microwave transmission spectrum, which is absent in previous calculation, can be recovered by altering the pinning condition of surface spins. The demonstrated reliability of our theory opens attractive perspectives for studying CMP of thin film with complicated surface magnetization distribution and magnetic multilayers.

Investigation of the binding between pepsin and nucleoside analogs by spectroscopy and molecular simulation.

PubMed

Li, Zhen; Li, Zhigang; Yang, Lingling; Xie, Yuanzhe; Shi, Jie; Wang, Ruiyong; Chang, Junbiao

2015-03-01

In this paper, the interactions of pepsin with CYD (cytidine) or nucleoside analogs, including FNC (2'-deoxy-2'-β-fluoro-4'-azidocytidine) and CMP (cytidine monophosphate), were investigated by fluorescence, UV-visible absorption and synchronous fluorescence spectroscopy under mimic physiological conditions. The results indicated that FNC (CYD/CMP) caused the fluorescence quenching by the formation of complex. The binding constants and thermo-dynamic parameters at three different temperatures were obtained. The hydrophobic and electrostatic interactions were the predominant intermolecular forces to stabilize the complex. The F atom in FNC might weaken the binding of nucleoside analog to pepsin. Results showed that CYD was the strongest quencher and bound to pepsin with higher affinity.

In situ measurement method for film thickness using transparency resin sheet with low refractive index under wet condition on chemical mechanical polishing

NASA Astrophysics Data System (ADS)

Oniki, Takahiro; Khajornrungruang, Panart; Suzuki, Keisuke

2017-07-01

We suggest that a transparency resin sheet with low refractive index can be applied to the measurement of a silicon dioxide (SiO2) film on a silicon wafer under wet condition for a film thickness measurement system on chemical mechanical polishing (CMP). By adjusting the refractive indices of the resin sheet and water, stable measurements of the SiO2 film can be expected, irrespective of slurry film thickness fluctuation because it has robustness against the slurry film. This result indicates that the transparency resin sheet with low refractive index is a useful for monitoring system of CMP.

Effect of magnetization boundary condition on cavity magnon polariton of YIG thin film

NASA Astrophysics Data System (ADS)

Jiang, H. H.; Xiao, Y.; Hu, C. M.; Guo, H.; Xia, K.

2018-06-01

Motivated by recent studies of cavity magnon polariton (CMP), we extended a previous theoretical work to generalize microwave transmission calculation with various magnetization boundary condition of YIG thin film embedded in cavity. It is found that numerical implementation given in this paper can be easily applied to other magnetization boundary condition and extended to magnetic multilayers. Numerical results show that ferromagnetic resonance mode of microwave transmission spectrum, which is absent in previous calculation, can be recovered by altering the pinning condition of surface spins. The demonstrated reliability of our theory opens attractive perspectives for studying CMP of thin film with complicated surface magnetization distribution and magnetic multilayers.

Instrumentation, performance visualization, and debugging tools for multiprocessors

NASA Technical Reports Server (NTRS)

Yan, Jerry C.; Fineman, Charles E.; Hontalas, Philip J.

1991-01-01

The need for computing power has forced a migration from serial computation on a single processor to parallel processing on multiprocessor architectures. However, without effective means to monitor (and visualize) program execution, debugging, and tuning parallel programs becomes intractably difficult as program complexity increases with the number of processors. Research on performance evaluation tools for multiprocessors is being carried out at ARC. Besides investigating new techniques for instrumenting, monitoring, and presenting the state of parallel program execution in a coherent and user-friendly manner, prototypes of software tools are being incorporated into the run-time environments of various hardware testbeds to evaluate their impact on user productivity. Our current tool set, the Ames Instrumentation Systems (AIMS), incorporates features from various software systems developed in academia and industry. The execution of FORTRAN programs on the Intel iPSC/860 can be automatically instrumented and monitored. Performance data collected in this manner can be displayed graphically on workstations supporting X-Windows. We have successfully compared various parallel algorithms for computational fluid dynamics (CFD) applications in collaboration with scientists from the Numerical Aerodynamic Simulation Systems Division. By performing these comparisons, we show that performance monitors and debuggers such as AIMS are practical and can illuminate the complex dynamics that occur within parallel programs.

Efficient partitioning and assignment on programs for multiprocessor execution

NASA Technical Reports Server (NTRS)

Standley, Hilda M.

1993-01-01

The general problem studied is that of segmenting or partitioning programs for distribution across a multiprocessor system. Efficient partitioning and the assignment of program elements are of great importance since the time consumed in this overhead activity may easily dominate the computation, effectively eliminating any gains made by the use of the parallelism. In this study, the partitioning of sequentially structured programs (written in FORTRAN) is evaluated. Heuristics, developed for similar applications are examined. Finally, a model for queueing networks with finite queues is developed which may be used to analyze multiprocessor system architectures with a shared memory approach to the problem of partitioning. The properties of sequentially written programs form obstacles to large scale (at the procedure or subroutine level) parallelization. Data dependencies of even the minutest nature, reflecting the sequential development of the program, severely limit parallelism. The design of heuristic algorithms is tied to the experience gained in the parallel splitting. Parallelism obtained through the physical separation of data has seen some success, especially at the data element level. Data parallelism on a grander scale requires models that accurately reflect the effects of blocking caused by finite queues. A model for the approximation of the performance of finite queueing networks is developed. This model makes use of the decomposition approach combined with the efficiency of product form solutions.

Kinetic measurement of 2-aminopurine X cytosine and 2-aminopurine X thymine base pairs as a test of DNA polymerase fidelity mechanisms.

PubMed Central

Watanabe, S M; Goodman, M F

1982-01-01

Enzyme kinetic measurements are presented showing that Km rather than maximum velocity (Vmax) discrimination governs the frequency of forming 2-aminopurine X cytosine base mispairs by DNA polymerase alpha. An in vitro system is used in which incorporation of dTMP or dCMP occurs opposite a template 2-aminopurine, and values for Km and Vmax are obtained. Results from a previous study in which dTTP and dCTP were competing simultaneously for insertion opposite 2-aminopurine indicated that dTMP is inserted 22 times more frequently than dCMP. We now report that the ratio of Km values KCm/KTm = 25 +/- 6, which agrees quantitatively with the dTMP/dCMP incorporation ratio obtained previously. We also report that VCmax is indistinguishable from VTmax. These Km and Vmax data are consistent with predictions from a model, the Km discrimination model, in which replication fidelity is determined by free energy differences between matched and mismatched base pairs. Central to this model is the prediction that the ratio of Km values for insertion of correct and incorrect nucleotides specifies the insertion fidelity, and the maximum velocities of insertion are the same for both nucleotides. PMID:6959128

Effect of photocatalytic oxidation technology on GaN CMP

NASA Astrophysics Data System (ADS)

Wang, Jie; Wang, Tongqing; Pan, Guoshun; Lu, Xinchun

2016-01-01

GaN is so hard and so chemically inert that it is difficult to obtain a high material removal rate (MRR) in the chemical mechanical polishing (CMP) process. This paper discusses the application of photocatalytic oxidation technology in GaN planarization. Three N-type semiconductor particles (TiO2, SnO2, and Fe2O3) are used as catalysts and added to the H2O2-SiO2-based slurry. By optical excitation, highly reactive photoinduced holes are produced on the surface of the particles, which can oxidize OH- and H2O absorbed on the surface of the catalysts; therefore, more OH* will be generated. As a result, GaN MRRs in an H2O2-SiO2-based polishing system combined with catalysts are improved significantly, especially when using TiO2, the MRR of which is 122 nm/h. The X-ray photoelectron spectroscopy (XPS) analysis shows the variation trend of chemical composition on the GaN surface after polishing, revealing the planarization process. Besides, the effect of pH on photocatalytic oxidation combined with TiO2 is analyzed deeply. Furthermore, the physical model of GaN CMP combined with photocatalytic oxidation technology is proposed to describe the removal mechanism of GaN.

Phosphorylation of uridine and cytidine by uridine-cytidine kinase.

PubMed

Qian, Yahui; Ding, Qingbao; Li, Yanyu; Zou, Zhi; Yan, Bingkun; Ou, Ling

2014-10-20

Uridine 5'-monophosphate (5'-UMP) and cytidine 5'-monophosphate (5'-CMP) were biosynthesized by recombinant uridine-cytidine kinase (UCK) and acetate kinase (ACK). The ack and uck genes from Escherichia coli K12 and the uck1, uck2 and ack genes from Lactobacillus bulgaricus ATCC 11842 were cloned and inserted into the plasmid pET-28a. All of the recombinant E. coli strains were capable of overexpressing UCK and ACK, which catalyzed the reaction using guanosine 5'-triphosphate (GTP) as a phosphate intermediate that was regenerated by ACK from acetyl phosphate. The effect of several parameters, including the substrate concentration, the GTP concentration, the temperature and the reaction pH, were optimized. High efficiency was achieved if uridine or cytidine was phosphorylated by UCK encoded by uck from E. coli and ACK encoded by ack from L. bulgaricus. The maximum conversion yield of 5'-UMP and 5'-CMP was 97% at 37 °C and pH 7.5 when 30 mM uridine/cytidine and 0.5mM GTP in a total of 1 mL were used. In addition, the 5'-UMP and 5'-CMP products were very stable in the reaction system and did not undergo significant degradation. Copyright © 2014 Elsevier B.V. All rights reserved.

Abrasive rolling effects on material removal and surface finish in chemical mechanical polishing analyzed by molecular dynamics simulation

NASA Astrophysics Data System (ADS)

Si, Lina; Guo, Dan; Luo, Jianbin; Lu, Xinchun; Xie, Guoxin

2011-04-01

In an abrasive chemical mechanical polishing (CMP) process, materials were considered to be removed by abrasive sliding and rolling. Abrasive sliding has been investigated by many molecular dynamics (MD) studies; while abrasive rolling was usually considered to be negligible and therefore was rarely investigated. In this paper, an MD simulation was used to study the effects of abrasive rolling on material removal and surface finish in the CMP process. As the silica particle rolled across the silicon substrate, some atoms of the substrate were dragged out from their original positions and adhered to the silica particle, leaving some atomic vacancies on the substrate surface. Meanwhile, a high quality surface could be obtained. During the abrasive rolling process, the influencing factors of material removal, e.g., external down force and driving force, were also discussed. Finally, MD simulations were carried out to examine the effects of abrasive sliding on material removal under the same external down force as abrasive rolling. The results showed that the ability of abrasive rolling to remove material on the atomic scale was not notably inferior to that of abrasive sliding. Therefore, it can be proposed that both abrasive sliding and rolling play important roles in material removal in the abrasive CMP of the silicon substrate.

Development of Rapid, Continuous Calibration Techniques and Implementation as a Prototype System for Civil Engineering Materials Evaluation

NASA Astrophysics Data System (ADS)

Scott, M. L.; Gagarin, N.; Mekemson, J. R.; Chintakunta, S. R.

2011-06-01

Until recently, civil engineering material calibration data could only be obtained from material sample cores or via time consuming, stationary calibration measurements in a limited number of locations. Calibration data are used to determine material propagation velocities of electromagnetic waves in test materials for use in layer thickness measurements and subsurface imaging. Limitations these calibration methods impose have been a significant impediment to broader use of nondestructive evaluation methods such as ground-penetrating radar (GPR). In 2006, a new rapid, continuous calibration approach was designed using simulation software to address these measurement limitations during a Federal Highway Administration (FHWA) research and development effort. This continuous calibration method combines a digitally-synthesized step-frequency (SF)-GPR array and a data collection protocol sequence for the common midpoint (CMP) method. Modeling and laboratory test results for various data collection protocols and materials are presented in this paper. The continuous-CMP concept was finally implemented for FHWA in a prototype demonstration system called the Advanced Pavement Evaluation (APE) system in 2009. Data from the continuous-CMP protocol is processed using a semblance/coherency analysis to determine material propagation velocities. Continuously calibrated pavement thicknesses measured with the APE system in 2009 are presented. This method is efficient, accurate, and cost-effective.

Immunoreactivity to food antigens in patients with chronic urticaria.

PubMed

Rašković, Sanvila; Matić, Ivana Z; Dorđić, Marija; Damjanović, Ana; Kolundžija, Branka; Grozdanić-Stanisavljević, Nađa; Besu, Irina; Jovičić, Zikica; Bijelić, Borivoj; Janković, Ljiljana; Juranić, Zorica

2014-01-01

The goal of study was better understanding of complex immune mechanisms that can help to evaluate patients with chronic urticaria (CU), especially those with unknown etiology. The study involved 55 patients with CU. Control group consisted of up to 90 healthy persons. The presence and intensity of serum IgG, IgA, IgM and IgE antibodies to common food antigens: cow's milk proteins (CMP), gliadin and phytohemagglutinin were determined by ELISA. Determination of subpopulations of immunocompetent cells was performed by flow cytometry. Significantly enhanced IgE, but also IgA immunity to CMP was found in patients with CU in comparison to healthy controls: (p < 0.000004) and (p < 0.002), respectively. Notably, in 40 out of 55 CU patients, the increased levels of some type of immunoglobulin reactivity to CMP were found. Regarding gliadin, only the levels of serum IgE anti-gliadin antibodies were significantly enhanced in patients with CU (p < 0.04). Significantly enhanced percentage of CD89+ cells accompanied with significantly lower percentage of lymphocytes and significantly higher mean fluorescence intensity of CD26 expression on lymphocytes were found in patients with CU in comparison to healthy controls (p < 0.04), (p < 0.02) and (p < 0.003), respectively. Results of this study may help in better understanding the complex immune disturbances in patients with CU.

Quality of ω-3 fatty acid enriched low-fat chicken meat patties incorporated with selected levels of linseed flour/oil and canola flour/oil.

PubMed

Singh, Ripudaman; Chatli, Manish K; Biswas, Ashim K; Sahoo, Jhari

2014-02-01

The aim of the present study was to compare the nutritional, processing and sensory characteristics of low-fat ω-3 enriched fatty acids chicken meat patties (CMP) prepared with the incorporation of 4% linseed flour (T1), 2% canola flour (T2), 3% linseed oil (T3), and 4% canola oil (T4) and to estimate their cost of production. The total fat and crude fiber content was increased (P < 0.05) with the incorporation of linseed flour. The emulsion stability and cooking yield was greater (P < 0.05) in T4 among all the treatments. The percent shrinkage was lower (P < 0.05) in linseed/canola oil incorporated CMP than their respective flours. The colour and appearance and flavour scores were lower (P < 0.05) in canola flour than canola oil incorporated CMP. The texture scores were not influenced (P < 0.05) in linseed-and canola-treated products. The overall acceptability was greatest (P < 0.05) in T4 whereas, lowest (P < 0.05) in T2 among all treated products. The cost of production was increased by 3-5% with the incorporation of linseed and canola oil whereas it was almost same for control and linseed flour.

Relation between isokinetic muscle strength and functional capacity in recreational athletes with chondromalacia patellae

PubMed Central

Yildiz, Y; Aydin, T; Sekir, U; Cetin, C; Ors, F; Alp, K

2003-01-01

Objectives: To investigate the effects of isokinetic exercise on pain and functional test scores of recreational athletes with chondromalacia patellae (CMP) and to examine the correlation between isokinetic parameters and functional tests or pain score. Methods: The functional ability of 30 recreational athletes with unilateral CMP was evaluated using six different tests. Pain scores were assessed during daily activities before and after the treatment protocol. Isokinetic exercise sessions were carried out at angular velocities of 60°/s (25–90° range of flexion) and 180°/s (full range). These sessions were repeated three times a week for six weeks. Results: Quadriceps and hamstring peak torque, total work, and endurance ratios had improved significantly after the treatment, as did the functional parameters and pain scores. There was a poor correlation between the extensor endurance ratio and one leg standing test. A moderate correlation between the visual analogue scale and the extensor endurance ratio or flexion endurance ratio was also found. Conclusions: The isokinetic exercise programme used in this study had a positive effect on muscle strength, pain score, and functional ability of knees with CMP. The improvement in the functional capacity did not correlate with the isokinetic parameters. PMID:14665581

Synergetic effect of chelating agent and nonionic surfactant for benzotriazole removal on post Cu-CMP cleaning

NASA Astrophysics Data System (ADS)

Yanlei, Li; Yuling, Liu; Chenwei, Wang; Yue, Li

2016-08-01

The cleaning of copper interconnects after chemical mechanical planarization (CMP) process is a critical step in integrated circuits (ICs) fabrication. Benzotriazole (BTA), which is used as corrosion inhibitor in the copper CMP slurry, is the primary source for the formation of organic contaminants. The presence of BTA can degrade the electrical properties and reliability of ICs which needs to be removed by using an effective cleaning solution. In this paper, an alkaline cleaning solution was proposed. The alkaline cleaning solution studied in this work consists of a chelating agent and a nonionic surfactant. The removal of BTA was characterized by contact angle measurements and potentiodynamic polarization studies. The cleaning properties of the proposed cleaning solution on a 300 mm copper patterned wafer were also quantified, total defect counts after cleaning was studied, scanning electron microscopy (SEM) review was used to identify types of BTA to confirm the ability of cleaning solution for BTA removal. All the results reveal that the chelating agent can effectively remove the BTA residual, nonionic surfactant can further improve the performance. Project supported by the Natural Science Foundation of Hebei Province, China (No. F2015202267) and the Scientific Innovation Grant for Excellent Young Scientists of Hebei University of Technology (No. 2015007).

Performance of colloidal silica and ceria based slurries on CMP of Si-face 6H-SiC substrates

NASA Astrophysics Data System (ADS)

Chen, Guomei; Ni, Zifeng; Xu, Laijun; Li, Qingzhong; Zhao, Yongwu

2015-12-01

Colloidal silica and ceria based slurries, both using KMnO4 as an oxidizer, for chemical mechanical polishing (CMP) of Si-face (0 0 0 1) 6H-SiC substrate, were investigated to obtain higher material removal rate (MRR) and ultra-smooth surface. The results indicate that there was a significant difference in the CMP performance of 6H-SiC between silica and ceria based slurries. For the ceria based slurries, a higher MRR was obtained, especially in strong acid KMnO4 environment, and the maximum MRR (1089 nm/h) and a smoother surface with an average roughness Ra of 0.11 nm was achieved using slurries containing 2 wt% colloidal ceria, 0.05 M KMnO4 at pH 2. In contrast, due to the attraction between negative charged silica particles and positive charged SiC surface below pH 5, the maximum MRR of silica based slurry was only 185 nm/h with surface roughness Ra of 0.254 nm using slurries containing 6 wt% colloidal silica, 0.05 M KMnO4 at pH 6. The polishing mechanism was discussed based on the zeta potential measurements of the abrasives and the X-ray photoelectron spectroscopy (XPS) analysis of the polished SiC surfaces.

Development of rapid, continuous calibration techniques and implementation as a prototype system for civil engineering materials evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, M. L.; Gagarin, N.; Mekemson, J. R.

Until recently, civil engineering material calibration data could only be obtained from material sample cores or via time consuming, stationary calibration measurements in a limited number of locations. Calibration data are used to determine material propagation velocities of electromagnetic waves in test materials for use in layer thickness measurements and subsurface imaging. Limitations these calibration methods impose have been a significant impediment to broader use of nondestructive evaluation methods such as ground-penetrating radar (GPR). In 2006, a new rapid, continuous calibration approach was designed using simulation software to address these measurement limitations during a Federal Highway Administration (FHWA) research andmore » development effort. This continuous calibration method combines a digitally-synthesized step-frequency (SF)-GPR array and a data collection protocol sequence for the common midpoint (CMP) method. Modeling and laboratory test results for various data collection protocols and materials are presented in this paper. The continuous-CMP concept was finally implemented for FHWA in a prototype demonstration system called the Advanced Pavement Evaluation (APE) system in 2009. Data from the continuous-CMP protocol is processed using a semblance/coherency analysis to determine material propagation velocities. Continuously calibrated pavement thicknesses measured with the APE system in 2009 are presented. This method is efficient, accurate, and cost-effective.« less

DESI-MS imaging and NMR spectroscopy to investigate the influence of biodiesel in the structure of commercial rubbers.

PubMed

Silva, Lorena M A; Alves Filho, Elenilson G; Simpson, André J; Monteiro, Marcos R; Cabral, Elaine; Ifa, Demian; Venâncio, Tiago

2017-10-01

Biodiesel has been introduced as an energetic matrix in several countries around the world. However, the affinity of biodiesel with the components of petrodiesel engines is a growing concern. In order to obtain information regarding the effect of biodiesel on the rubber structure, nuclear magnetic resonance technics under a new technology named as comprehensive multiphase (CMP NMR) and the imaging through desorption electrospray ionization mass spectrometry (DESI-MS imaging) were used. The 1 H CMP-DOSY NMR showed the entrapped fuel into the rubber cavities, which the higher constraint caused by the rubber structure is related to the smaller diffusion coefficient. The less affected type of rubber by biodiesel was ethylene-propylene-diene monomer (EPDM), and the most affected was synthetic rubber nitrile (NBR). The 13 C CMP MAS-SPE experiments also confirmed that the internal region of EPDM was less accessible to the biodiesel molecules (no fuels detected) while other rubbers were more susceptible to the penetration of the fuel. DESI-MS imaging revealed for the first time the topography of the rubbers exposed to fuels. The biodiesel molecules entrapped at the EPDM and NBR pores were in oxidized form, which might degrade the rubber structure at long exposure time. The employed technics enabled the study of dynamic and molecular structure of the mixing complex multiphase. The DOSY under CMP used in this study could prove helpful in assessing the interactions throughout all physical phases (liquid, solid, and gel or semi-solid) by observing swellability caused by the fuel in the rubber. In addition, the DESI-MS was especially valuable to detect the degradation products of biodiesel entangled at the rubber structure. In our knowledge, this was the first report in which chemical changes of commercial rubbers induced by biodiesel and petrodiesel were investigated by means of DESI-MS and DOSY NMR. Copyright © 2017 Elsevier B.V. All rights reserved.

The choline-depleted type II pneumonocyte. A model for investigating the synthesis of surfactant lipids.

PubMed Central

Anceschi, M M; Di Renzo, G C; Venincasa, M D; Bleasdale, J E

1984-01-01

When type II pneumonocytes from adult rats were maintained in a medium that lacked choline, the incorporation of [14C]glycerol into phosphatidylcholine was not greatly diminished during the period that the cells displayed characteristics of type II pneumonocytes. Cells that were maintained in choline-free medium that contained choline oxidase and catalase, however, became depleted of choline and subsequent synthesis of phosphatidylcholine by these cells was responsive to choline in the extracellular medium. Incorporation of [14C]glycerol into phosphatidylcholine by choline-depleted cells was stimulated maximally (approx. 6-fold) by extracellular choline at a concentration (0.05 mM) that also supported the greatest incorporation into phosphatidylglycerol. The incorporation of [14C]glycerol into other glycerophospholipids by choline-depleted cells was not increased by extracellular choline. When cells were incubated in the presence of [3H]cytidine, the choline-dependent stimulation of the synthesis of phosphatidylcholine and phosphatidylglycerol was accompanied by an increased recovery of [3H]CMP. This increased recovery of [3H]CMP reflected an increase in the intracellular amount of CMP from 48 +/- 9 to 76 +/- 16 pmol/10(6) cells. Choline-depleted cells that were exposed to [3H]choline contained [3H]CDP-choline as the principal water-soluble choline derivative. As the extracellular concentration of choline was increase, however, the amount of 3H in phosphocholine greatly exceeded that in all other water-soluble derivatives. Choline-depletion of cells resulted in an increase in the specific activity of CTP:phosphocholine cytidylyltransferase in cell homogenates (from 0.40 +/- 0.15 to 1.31 +/- 0.20 nmol X min-1 X mg of protein-1). These data are indicative that the biosynthesis of phosphatidylcholine is integrated with that of phosphatidylglycerol and are consistent with the proposed involvement of CMP in this integration. The choline-depleted type II pneumonocyte provides a new model for investigating the regulation of CTP:phosphocholine cytidylyltransferase activity. PMID:6548908

Cytosine substituted calix[4]pyrroles: Neutral receptors for 5′-guanosine monophosphate

PubMed Central

Sessler, Jonathan L.; Král, Vladimír; Shishkanova, Tatiana V.; Gale, Philip A.

2002-01-01

The synthesis and characterization of two cytosine-substituted calix[4]pyrrole conjugates, bearing the appended cytosine attached at either a β- or meso-pyrrolic position, is described. These systems were tested as nucleotide-selective carriers and as active components of nucleotide-sensing ion-selective electrodes at pH 6.6. Studies of carrier selectivity were made using a Pressman-type model membrane system consisting of an initial pH 6.0 aqueous phase, an intervening dichloromethane barrier containing the calix[4]pyrrole conjugate, and a receiving basic aqueous phase. Good selectivity for the Watson–Crick complementary nucleotide, 5′-guanosine monophosphate (5′-GMP), was seen in the case of the meso-linked conjugate with the relative rates of through-membrane transport being 7.7:4.1:1 for 5′-GMP, 5′-AMP, and 5′-CMP, respectively. By contrast, the β-substituted conjugate, while showing a selectivity for 5′-GMP that was enhanced relative to unsubstituted calix[4]pyrrole, was found to transport 5′-CMP roughly 4.5 times more quickly than 5′-GMP. Higher selectivities were also found for 5′-CMP when both the β- and meso-substituted conjugates were incorporated into polyvinyl chloride membranes and tested as ion selective electrodes at pH 6.6, whereas near-equal selectivities were observed for 5′-CMP and 5′-GMP in the case of unsubstituted calix[4]pyrroles. These seemingly disparate results are consistent with a picture wherein the meso-substituted cytosine calix[4]pyrrole conjugate, but not its β-linked congener, is capable of acting as a ditopic receptor, binding concurrently both the phosphate anion and nucleobase portions of 5′-GMP to the calixpyrrole core and cytosine “tails” of the molecule, respectively, with the effect of this binding being most apparent under the conditions of the transport experiments. PMID:11929967

Does Mindfulness Improve After Heart Coherence Training in Patients With Chronic Musculoskeletal Pain and Healthy Subjects? A Pilot Study.

PubMed

Soer, Remko; de Jong, Annemieke B; Hofstra, Bert L; Preuper, Henrica R Schiphorst; Reneman, Michiel F

2015-07-01

Mindfulness and heart coherence training (HCT) training are applied increasingly in the treatment of patients with chronic musculoskeletal pain (CMP). Questionnaires have been developed to assess changes in mindfulness but no gold standard is available. Explore the relationship between changes in mindfulness scores and changes in heart coherence after 3 sessions of HCT in patients with CMP and in healthy subjects. Ten patients with CMP and 15 healthy subjects were trained in self-regulation with the use of HCT following a standardized stress relief program developed by the HeartMath Institute. A heart coherence-score (HC-score) was constructed with scores ranging from 0-100 with higher scores reflecting more heart rate variability (HRV) coherency. Change scores, Spearman correlation coefficients, and Wilcoxon Signed Rank test were calculated to test relationships and differences between HC-score, the Mindfulness Attention and Awareness Scale (MAAS) and Five Facet Mindfulness Questionnaire (FFMQ). A new questionnaire was constructed to explore on which mindfulness-related domains patients with CMP report changes after HCT. Increases were present on HC-score in healthy subjects (P<.01) and in patients (P<.01) between baseline and follow-up. Effect sizes on change on the MAAS and FFMQ were low. Weak (r<0.25) and non-significant correlations were observed in change scores between HC-score and MAAS or FFMQ. Patients reported significant favorable differences on 6 mindfulness related domains in the new questionnaire: breathing rhythm, physical awareness, positive or negative emotions, recognition of stressful situations, thoughts, and tendency to actively self-regulate. In this pilot study, mindfulness as assessed by the MAAS and FFMQ does not appear to improve after HCT. HRV coherency, MAAS, and FFMQ measure different constructs and are weakly related. It is of great importance to choose and develop valid measures that reflect patients' states of mindfulness. Content and face validity of measures of mindfulness may be considered in the light of performance-based measures.

The peroxynitrite donor 3-morpholinosydnonimine induces reversible changes in electrophysiological properties of neurons of the guinea-pig spinal cord.

PubMed

Ashki, N; Hayes, K C; Bao, F

2008-09-22

Elevated concentrations of nitric oxide (NO) and peroxynitrite (ONOO(-)) are present within the CNS following neurotrauma and are implicated in the pathogenesis of the accompanying neurologic deficits. We tested the hypothesis that elevated extracellular concentrations of ONOO(-), introduced by the donor 3-morpholinosydnonimine (SIN-1), induce reversible axonal conduction deficits in neurons of the guinea-pig spinal cord. The compound action potential (CAP) and compound membrane potential (CMP) of excised ventral cord white matter were recorded before, during, and after, bathing the tissue (30 min) in varying concentrations (0.125-2.0 mM) of SIN-1 (3.75-60 microM ONOO(-)). The principal results were rapid onset, concentration-dependent, reductions in amplitude of the CAP (P<0.05). At a concentration of 0.25 mM of SIN-1 the reduction in CAP amplitude was fully reversible and was not accompanied by any changes in CMP. At higher concentrations of SIN-1 (> or =0.5 mM) the reversibility was incomplete and there was concurrent depolarization of the CMP. These electrophysiological changes were not evident when the donor had been a priori depleted of ONOO(-) by uric acid or was co-administered with the ONOO(-) scavenger ebselen (3 mM). Immuno-fluorescence staining for nitrotyrosine (Ntyr) revealed extensive nitration of tyrosine residues in neurons exposed to higher concentrations of SIN-1. These results are the first to demonstrate that ONOO(-) induces reversible conduction deficits within axons of the spinal cord. The dissociation of CAP and CMP changes at low concentrations of SIN-1, when the CAP changes were reversible and there was no evidence of nitration of tyrosine residues, is consistent with ONOO(-)-induced alteration in Na+ channel conductance in the axolemma. The results support the view that ONOO(-) contributes to both reversible and non-reversible neurologic deficits following neurotrauma. The reversal of immune-mediated conduction deficits may contribute to spontaneous neurologic deficits following neurotrauma.

The length-force behavior and operating length range of squid muscle vary as a function of position in the mantle wall.

PubMed

Thompson, Joseph T; Shelton, Ryan M; Kier, William M

2014-06-15

Hollow cylindrical muscular organs are widespread in animals and are effective in providing support for locomotion and movement, yet are subject to significant non-uniformities in circumferential muscle strain. During contraction of the mantle of squid, the circular muscle fibers along the inner (lumen) surface of the mantle experience circumferential strains 1.3 to 1.6 times greater than fibers along the outer surface of the mantle. This transmural gradient of strain may require the circular muscle fibers near the inner and outer surfaces of the mantle to operate in different regions of the length-tension curve during a given mantle contraction cycle. We tested the hypothesis that circular muscle contractile properties vary transmurally in the mantle of the Atlantic longfin squid, Doryteuthis pealeii. We found that both the length-twitch force and length-tetanic force relationships of the obliquely striated, central mitochondria-poor (CMP) circular muscle fibers varied with radial position in the mantle wall. CMP circular fibers near the inner surface of the mantle produced higher force relative to maximum isometric tetanic force, P0, at all points along the ascending limb of the length-tension curve than CMP circular fibers near the outer surface of the mantle. The mean ± s.d. maximum isometric tetanic stresses at L₀ (the preparation length that produced the maximum isometric tetanic force) of 212 ± 105 and 290 ± 166 kN m(-2) for the fibers from the outer and inner surfaces of the mantle, respectively, did not differ significantly (P=0.29). The mean twitch:tetanus ratios for the outer and inner preparations, 0.60 ± 0.085 and 0.58 ± 0.10, respectively, did not differ significantly (P=0.67). The circular fibers did not exhibit length-dependent changes in contraction kinetics when given a twitch stimulus. As the stimulation frequency increased, L₀ was approximately 1.06 times longer than LTW, the mean preparation length that yielded maximum isometric twitch force. Sonomicrometry experiments revealed that the CMP circular muscle fibers operated in vivo primarily along the ascending limb of the length-tension curve. The CMP fibers functioned routinely over muscle lengths at which force output ranged from only 85% to 40% of P₀, and during escape jets from 100% to 30% of P₀. Our work shows that the functional diversity of obliquely striated muscles is much greater than previously recognized. © 2014. Published by The Company of Biologists Ltd.

Portable programming on parallel/networked computers using the Application Portable Parallel Library (APPL)

NASA Technical Reports Server (NTRS)

Quealy, Angela; Cole, Gary L.; Blech, Richard A.

1993-01-01

The Application Portable Parallel Library (APPL) is a subroutine-based library of communication primitives that is callable from applications written in FORTRAN or C. APPL provides a consistent programmer interface to a variety of distributed and shared-memory multiprocessor MIMD machines. The objective of APPL is to minimize the effort required to move parallel applications from one machine to another, or to a network of homogeneous machines. APPL encompasses many of the message-passing primitives that are currently available on commercial multiprocessor systems. This paper describes APPL (version 2.3.1) and its usage, reports the status of the APPL project, and indicates possible directions for the future. Several applications using APPL are discussed, as well as performance and overhead results.

High-performance multiprocessor architecture for a 3-D lattice gas model

NASA Technical Reports Server (NTRS)

Lee, F.; Flynn, M.; Morf, M.

1991-01-01

The lattice gas method has recently emerged as a promising discrete particle simulation method in areas such as fluid dynamics. We present a very high-performance scalable multiprocessor architecture, called ALGE, proposed for the simulation of a realistic 3-D lattice gas model, Henon's 24-bit FCHC isometric model. Each of these VLSI processors is as powerful as a CRAY-2 for this application. ALGE is scalable in the sense that it achieves linear speedup for both fixed and increasing problem sizes with more processors. The core computation of a lattice gas model consists of many repetitions of two alternating phases: particle collision and propagation. Functional decomposition by symmetry group and virtual move are the respective keys to efficient implementation of collision and propagation.

Shared Memory Parallelization of an Implicit ADI-type CFD Code

NASA Technical Reports Server (NTRS)

Hauser, Th.; Huang, P. G.

1999-01-01

A parallelization study designed for ADI-type algorithms is presented using the OpenMP specification for shared-memory multiprocessor programming. Details of optimizations specifically addressed to cache-based computer architectures are described and performance measurements for the single and multiprocessor implementation are summarized. The paper demonstrates that optimization of memory access on a cache-based computer architecture controls the performance of the computational algorithm. A hybrid MPI/OpenMP approach is proposed for clusters of shared memory machines to further enhance the parallel performance. The method is applied to develop a new LES/DNS code, named LESTool. A preliminary DNS calculation of a fully developed channel flow at a Reynolds number of 180, Re(sub tau) = 180, has shown good agreement with existing data.

The performance of disk arrays in shared-memory database machines

NASA Technical Reports Server (NTRS)

Katz, Randy H.; Hong, Wei

1993-01-01

In this paper, we examine how disk arrays and shared memory multiprocessors lead to an effective method for constructing database machines for general-purpose complex query processing. We show that disk arrays can lead to cost-effective storage systems if they are configured from suitably small formfactor disk drives. We introduce the storage system metric data temperature as a way to evaluate how well a disk configuration can sustain its workload, and we show that disk arrays can sustain the same data temperature as a more expensive mirrored-disk configuration. We use the metric to evaluate the performance of disk arrays in XPRS, an operational shared-memory multiprocessor database system being developed at the University of California, Berkeley.

Dynamic programming on a shared-memory multiprocessor

NASA Technical Reports Server (NTRS)

Edmonds, Phil; Chu, Eleanor; George, Alan

1993-01-01

Three new algorithms for solving dynamic programming problems on a shared-memory parallel computer are described. All three algorithms attempt to balance work load, while keeping synchronization cost low. In particular, for a multiprocessor having p processors, an analysis of the best algorithm shows that the arithmetic cost is O(n-cubed/6p) and that the synchronization cost is O(absolute value of log sub C n) if p much less than n, where C = (2p-1)/(2p + 1) and n is the size of the problem. The low synchronization cost is important for machines where synchronization is expensive. Analysis and experiments show that the best algorithm is effective in balancing the work load and producing high efficiency.

Geometry-based across wafer process control in a dual damascene scenario

NASA Astrophysics Data System (ADS)

Krause, Gerd; Hofmann, Detlef; Habets, Boris; Buhl, Stefan; Gutsch, Manuela; Lopez-Gomez, Alberto; Thrun, Xaver

2018-03-01

Dual damascene is an established patterning process for back-end-of-line to generate copper interconnects and lines. One of the critical output parameters is the electrical resistance of the metal lines. In our 200 mm line, this is currently being controlled by a feed-forward control from the etch process to the final step in the CMP process. In this paper, we investigate the impact of alternative feed-forward control using a calibrated physical model that estimates the impact on electrical resistance of the metal lines* . This is done by simulation on a large set of wafers. Three different approaches are evaluated, one of which uses different feed-forward settings for different radial zones in the CMP process.

Influence of Wafer Edge Geometry on Removal Rate Profile in Chemical Mechanical Polishing: Wafer Edge Roll-Off and Notch

NASA Astrophysics Data System (ADS)

Fukuda, Akira; Fukuda, Tetsuo; Fukunaga, Akira; Tsujimura, Manabu

2012-05-01

In the chemical mechanical polishing (CMP) process, uniform polishing up to near the wafer edge is essential to reduce edge exclusion and improve yield. In this study, we examine the influences of inherent wafer edge geometries, i.e., wafer edge roll-off and notch, on the CMP removal rate profile. We clarify the areas in which the removal rate profile is affected by the wafer edge roll-off and the notch, as well as the intensity of their effects on the removal rate profile. In addition, we propose the use of a small notch to reduce the influence of the wafer notch and present the results of an examination by finite element method (FEM) analysis.

Synthesis and biological evaluation of several dephosphonated analogues of CMP-Neu5Ac as inhibitors of GM3-synthase.

PubMed

Rota, Paola; Cirillo, Federica; Piccoli, Marco; Gregorio, Antonio; Tettamanti, Guido; Allevi, Pietro; Anastasia, Luigi

2015-10-05

Previous studies demonstrated that reducing the GM3 content in myoblasts increased the cell resistance to hypoxic stress, suggesting that a pharmacological inhibition of the GM3 synthesis could be instrumental for the development of new treatments for ischemic diseases. Herein, the synthesis of several dephosphonated CMP-Neu5Ac congeners and their anti-GM3-synthase activity is reported. Biological activity testes revealed that some inhibitors almost completely blocked the GM3-synthase activity in vitro and reduced the GM3 content in living embryonic kidney 293A cells, eventually activating the epidermal growth factor receptor (EGFR) signaling cascade. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

42 CFR 417.434 - Reenrollment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PROGRAM HEALTH MAINTENANCE ORGANIZATIONS, COMPETITIVE MEDICAL PLANS, AND HEALTH CARE PREPAYMENT PLANS Enrollment, Entitlement, and Disenrollment under Medicare Contract § 417.434 Reenrollment. If an HMO or CMP...

Silicon-on-insulator with hybrid orientations for heterogeneous integration of GaN on Si (100) substrate

NASA Astrophysics Data System (ADS)

Zhang, Runchun; Zhao, Beiji; Huang, Kai; You, Tiangui; Jia, Qi; Lin, Jiajie; Zhang, Shibin; Yan, Youquan; Yi, Ailun; Zhou, Min; Ou, Xin

2018-05-01

Heterogeneous integration of materials pave a new way for the development of the microsystem with miniaturization and complex functionalities. Two types of hybrid silicon on insulator (SOI) structures, i.e., Si (100)-on-Si (111) and Si (111)-on-Si (100), were prepared by the smart-cut technique, which is consist of ion-slicing and wafer bonding. The precise calculation of the lattice strain of the transferred films without the epitaxial matching relationship to the substrate was demonstrated based on X-ray diffraction (XRD) measurements. The XRD and Raman measurement results suggest that the transferred films possess single crystalline quality. With a chemical mechanical polishing (CMP) process, the surface roughness of the transferred thin films can be reduced from 5.57 nm to 0.30 nm. The 4-inch GaN thin film epitaxially grown on the as-prepared hybrid SOI of Si (111)-on-Si (100) by metalorganic chemical vapor deposition (MOCVD) is of improved quality with a full width at half maximum (FWHM) of 672.54 arcsec extracted from the XRD rocking curve and small surface roughness of 0.40 nm. The wafer-scale GaN on Si (111)-on-Si (100) can serve as a potential platform for the one chip integration of GaN-based high electron mobility transistors (HEMT) or photonics with the Si (100)-based complementary metal oxide semiconductor (CMOS).

Experimental Studies of Selected Aqueous Electrochemical Systems Relevant for Materials Processing in the Fabrications of Microelectronic Components and Direct Alcohol Fuel Cells

NASA Astrophysics Data System (ADS)

Shi, Xingzhao

A broad range of electrochemical techniques are employed in this dissertation to investigate a selected set of aqueous electrochemical systems that are relevant for materials processing in the fabrication of microelectronic devices and direct alcohol fuel cells. In terms of technical applications, this work covers three main experimental systems: (i) chemical mechanical planarization (CMP), (ii) electro-less nickel deposition, and (iii) direct alkaline glycerol fuel cells. The first two areas are related to electronic device fabrications and the third topic is related to cost-effective energy conversion. The common electrochemical aspect of these different systems is that, in all these cases the active material characteristics are governed by complex (often multi-step) reactions occurring at metal-liquid (aqueous) interfaces. Electro-analytical techniques are ideally suited for studying the detailed mechanisms of such reactions, and the present investigation is largely focused on developing adequate analytical strategies for probing these reaction mechanisms. In the fabrication of integrated circuits, certain steps of materials processing involve CMP of Al deposited on thin layers of diffusion barrier materials like Ta/TaN, Co, or Ti/TiN. A specific example of this situation is found in the processing of replacement metal gates used for high-k/metal-gate transistors. Since the commonly used barrier materials are nobler than Al, the Al interface in contact with the barrier can become prone to galvanic corrosion in the wet CMP environment. Using model systems of coupon electrodes and two specific barrier metals, Ta and Co, the electrochemical factors responsible for these corrosion effects are investigated here in a moderately acidic (pH = 4.0) abrasive-free solution. The techniques of cyclic voltammetry and impedance spectroscopy are combined with strategic measurements of galvanic currents and open circuit potentials (OCPs). L-ascorbic acid (AA) is employed as a surface modifying agent for controlling galvanic corrosions of Al in the Ta-Al and Co-Al bimetallic combinations. The results elaborate the chemical and electrochemical mechanisms responsible for activating and suppressing the corrosion processes in these systems. Defect-control is a critical requirement for CMP of the ultrathin diffusion barriers considered for the new Cu-interconnects. The challenging task of developing advanced CMP slurries for such systems can be aided by electrochemical evaluations of model CMP schemes under tribological conditions. The present work uses this strategy to characterize an alkaline slurry formulation aimed at minimizing galvanic corrosion in the CMP systems involving Ru, Ta (barrier metals) and Cu (wiring metal). This slurry is based on percarbonate and guanidine additives, and the test metals are polycrystalline disc samples. A particular goal of this study is to explore the essential analytical aspects of evaluating CMP systems in the tribo-electrochemical approach. The CMP specific surface reactions are characterized by potentiodynamic polarization and open circuit voltage measurements, performed both in the presence and in the absence of polishing, and by employing abrasive free as well as abrasive (colloidal SiO 2) added solutions. The findings of these experiments are further checked by using impedance spectroscopy. The electrochemical mixed potential steps of the CMP promoting reactions are analyzed, and the removable surface species formed by these reactions are discussed. Electro-oxidation of hypophosphite plays an important role in the electro-less deposition of Ni used to fabricate surface engineered films, alloys, and coatings for a variety of applications. At the same time, the kinetic details of this oxidation reaction comprise an ideal framework for studying many general mechanistic aspects of electrocatalysis on transition metal substrates. The present study utilizes these specific attributes of hypophosphite oxidation to probe the underlying function of the incipient hydrous oxide of Ni in promoting the catalytic properties of this metal in an alkaline medium. The experiments reported here use time-resolved Fourier-transform electrochemical impedance spectroscopy (FT-EIS), strategically coupled with scan-rate controlled voltammetry. The results suggest that the incipient hydrous oxide Ni(OH)ad formed at the onset of hypophosphite oxidation catalytically promotes the latter's precursor de-hydrogenation step. While voltammetry provides suggestive evidence for these Ni(OH)ad induced effects, the FT-EIS data serve to gather more direct signatures of the catalytic function of Ni(OH)ad. The mechanism of energy conversion in a direct glycerol fuel cell (DGFC) is governed by the anode-supported heterogeneous steps of glycerol electro-oxidation. In aerated alkaline electrolytes, glycerol also participates in a base catalyzed process, which can release certain species mixing with the anode catalyzed surface products. As a result, selective probing of the surface catalytic reactions involving such systems can be difficult. The present work addresses this issue for a gold anode by using the analytical capability of cyclic voltammetry (CV). In addition, surface plasmon resonance measurements are used to optically probe the adsorption characteristics of the electrolyte species. The net exchange current of the oxidation process and the transfer coefficient of the rate determining step are evaluated by analyzing the CV data. The interfacial reactions and their products on Au are identified by measuring the number of electrons released during the electro-oxidation of glycerol. The results indicate that these reactions are facilitated by the surface bound hydroxyl species on Au (chemisorbed OH-- and faradaically formed Au-OH). By comparing the findings for stationary and rotating electrodes, it is shown that, convective mass transport is critical to maintaining efficient progression of the consecutive oxidation steps of glycerol. In the absence of hydrodynamic support, the main surface products of glycerol oxidation appear to be glyceraldehyde, glycerate and malonate, formed through a net six-electron route. In the presence of controlled convection, a ten-electron process is activated, where mesaxolate is the likely additional product.

Field demonstration of reduction of lead availability in soil and cabbage (Brassica Chinensis L.) contaminated by mining tailings using phosphorus fertilizers*

PubMed Central

Xie, Zheng-miao; Wang, Bi-ling; Sun, Ye-fang; Li, Jing

2006-01-01

A field demonstration of reduction of lead availability in a soil and cabbage (Brassica Chinensis L.) contaminated by mining tailings, located in Shaoxing, China was carried out to evaluate the effects of applications of phosphorus fertilizers on Pb fractionation and Pb phytoavailability in the soil. It was found that the addition of all three P fertilizers including single super phosphate (SSP), phosphate rock (PR), and calcium magnesium phosphate (CMP) significantly decreased the percentage of water-soluble and exchangeable (WE) soil Pb and then reduced the uptake of Pb, Cd, and Zn by the cabbage compared to the control (CK). The results showed that the level of 300 g P/m2 soil was the most cost-effective application rate of P fertilizers for reducing Pb availability at the first stage of remediation, and that at this P level, the effect of WE fraction of Pb in the soil decreased by three phosphorus fertilizers followed the order: CMP (79%)>SSP (41%)>PR (23%); Effectiveness on the reduction of Pb uptake by cabbage was in the order: CMP (53%)>SSP (41%)>PR (30%). Therefore our field trial demonstrated that it was effective and feasible to reduce Pb availability in soil and cabbage contaminated by mining tailings using P fertilizers in China and PR would be a most cost-effective amendment. PMID:16365925

Signal processing and analysis for copper layer thickness measurement within a large variation range in the CMP process.

PubMed

Li, Hongkai; Zhao, Qian; Lu, Xinchun; Luo, Jianbin

2017-11-01

In the copper (Cu) chemical mechanical planarization (CMP) process, accurate determination of a process reaching the end point is of great importance. Based on the eddy current technology, the in situ thickness measurement of the Cu layer is feasible. Previous research studies focus on the application of the eddy current method to the metal layer thickness measurement or endpoint detection. In this paper, an in situ measurement system, which is independently developed by using the eddy current method, is applied to the actual Cu CMP process. A series of experiments are done for further analyzing the dynamic response characteristic of the output signal within different thickness variation ranges. In this study, the voltage difference of the output signal is used to represent the thickness of the Cu layer, and we can extract the voltage difference variations from the output signal fast by using the proposed data processing algorithm. The results show that the voltage difference decreases as thickness decreases in the conventional measurement range and the sensitivity increases at the same time. However, it is also found that there exists a thickness threshold, and the correlation is negative, when the thickness is more than the threshold. Furthermore, it is possible that the in situ measurement system can be used within a larger Cu layer thickness variation range by creating two calibration tables.

Development of Formulations for a-SiC and Manganese CMP and Post-CMP Cleaning of Cobalt

NASA Astrophysics Data System (ADS)

Lagudu, Uma Rames Krishna

We have investigated the chemical mechanical polishing (CMP) of amorphous SiC (a-SiC) and Mn and Post CMP cleaning of cobalt for various device applications. During the manufacture of copper interconnects using the damascene process the polishing of copper is followed by the polishing of the barrier material (Co, Mn, Ru and their alloys) and its post CMP cleaning. This is followed by the a-SiC hard mask CMP. Silicon carbide thin films, though of widespread use in microelectronic engineering, are difficult to process by CMP because of their hardness and chemical inertness. The earlier part of the SiC work discusses the development of slurries based on silica abrasives that resulted in high a-SiC removal rates (RRs). The ionic strength of the silica dispersion was found to play a significant role in enhancing material removal rate, while also providing very good post-polish surface-smoothness. For example, the addition of 50 mM potassium nitrate to a pH 8 aqueous slurry consisting of 10 wt % of silica abrasives and 1.47 M hydrogen peroxide increased the RR from about 150 nm/h to about 2100 nm/h. The role of ionic strength in obtaining such high RRs was investigated using surface zeta-potentials measurements and X-ray photoelectron spectroscopy (XPS). Evidently, hydrogen peroxide promoted the oxidation of Si and C to form weakly adhered species that were subsequently removed by the abrasive action of the silica particles. The effect of potassium nitrate in increasing material removal is attributed to the reduction in the electrostatic repulsion between the abrasive particles and the SiC surface because of screening of surface charges by the added electrolyte. We also show that transition metal compounds when used as additives to silica dispersions enhance a-SiC removal rates (RRs). Silica slurries containing potassium permanganate gave RRs as high as 2000 nm/h at pH 4. Addition of copper sulfate to this slurry further enhanced the RRs to ˜3500 nm/h at pH 6. Furthermore, addition of a low concentration of 250 ppm Brij-35 to this slurry suppressed the RRs of silicon dioxide to zero, while retaining the RRs of a-SiC at ˜2700 nm/h , a combination of RRs that is appropriate for hard mask polishing. The second part of this thesis focuses on the polishing of manganese which was proposed as a "self-forming" barrier material to prevent copper diffusion in advanced generation (22 nm and smaller) Si devices. A major challenge associated with such a self-forming Mn barrier for Cu interconnects in sub-22nm devices is galvanic corrosion that can occur at the Cu-Mn interface during chemical mechanical planarization. In the present work, it was shown that an aqueous solution of sucrose, BTA and potassium periodate reduces the corrosion potential gap between Cu and Mn to ˜ 0.01 V at pH 10 while also lowering the galvanic currents significantly and hence can be an excellent candidate for a polishing slurry. We discuss the role of these reagents and the inhibiting film that can be formed at the interface of the bimetallic system in this solution. Preliminary polishing results for Cu and Mn using a silica-based slurry formulated with this solution are also presented. The third part involves the development of compositions for Post CMP cleaning of cobalt barriers in advanced generation (22 nm and smaller). The thickness of the cobalt films was found to impact the corrosion behavior of the films. Thinner films of cobalt were found be more prone to galvanic corrosion in the presence of copper. The corrosion currents were low for both Cu and Co in all the solutions tested but the galvanic currents varied significantly. It was found that while BTA was not able to suppress the galvanic corrosion between Cu and Co (2000 A) at pH 8, either 60 mM of 3 Amino 1,2,4 triazole or 30 mM of 3 Amino 5 methyl thio 1,2,4 triazole were able to suppress the galvanic corrosion between Cu and Co (2000 A) to < 0.3 micro amperes per square cm at pH 8. These compositions however were not able to suppress the galvanic corrosion of Co (20 A) films. Changing the pH to 10 did not improve the results. Furthermore, addition of several complexing agents and other corrosion inhibitors also did not lower the Ecorr of Co (20 A) and Cu. Further experiments are being conducted to identify compositions to protect Co and Cu from corrosion. (Abstract shortened by UMI.).

Multiprocessor shared-memory information exchange

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santoline, L.L.; Bowers, M.D.; Crew, A.W.

1989-02-01

In distributed microprocessor-based instrumentation and control systems, the inter-and intra-subsystem communication requirements ultimately form the basis for the overall system architecture. This paper describes a software protocol which addresses the intra-subsystem communications problem. Specifically the protocol allows for multiple processors to exchange information via a shared-memory interface. The authors primary goal is to provide a reliable means for information to be exchanged between central application processor boards (masters) and dedicated function processor boards (slaves) in a single computer chassis. The resultant Multiprocessor Shared-Memory Information Exchange (MSMIE) protocol, a standard master-slave shared-memory interface suitable for use in nuclear safety systems, ismore » designed to pass unidirectional buffers of information between the processors while providing a minimum, deterministic cycle time for this data exchange.« less

Multiprocessor Neural Network in Healthcare.

PubMed

Godó, Zoltán Attila; Kiss, Gábor; Kocsis, Dénes

2015-01-01

A possible way of creating a multiprocessor artificial neural network is by the use of microcontrollers. The RISC processors' high performance and the large number of I/O ports mean they are greatly suitable for creating such a system. During our research, we wanted to see if it is possible to efficiently create interaction between the artifical neural network and the natural nervous system. To achieve as much analogy to the living nervous system as possible, we created a frequency-modulated analog connection between the units. Our system is connected to the living nervous system through 128 microelectrodes. Two-way communication is provided through A/D transformation, which is even capable of testing psychopharmacons. The microcontroller-based analog artificial neural network can play a great role in medical singal processing, such as ECG, EEG etc.

Characterizing parallel file-access patterns on a large-scale multiprocessor

NASA Technical Reports Server (NTRS)

Purakayastha, A.; Ellis, Carla; Kotz, David; Nieuwejaar, Nils; Best, Michael L.

1995-01-01

High-performance parallel file systems are needed to satisfy tremendous I/O requirements of parallel scientific applications. The design of such high-performance parallel file systems depends on a comprehensive understanding of the expected workload, but so far there have been very few usage studies of multiprocessor file systems. This paper is part of the CHARISMA project, which intends to fill this void by measuring real file-system workloads on various production parallel machines. In particular, we present results from the CM-5 at the National Center for Supercomputing Applications. Our results are unique because we collect information about nearly every individual I/O request from the mix of jobs running on the machine. Analysis of the traces leads to various recommendations for parallel file-system design.

Dynamic modelling and estimation of the error due to asynchronism in a redundant asynchronous multiprocessor system

NASA Technical Reports Server (NTRS)

Huynh, Loc C.; Duval, R. W.

1986-01-01

The use of Redundant Asynchronous Multiprocessor System to achieve ultrareliable Fault Tolerant Control Systems shows great promise. The development has been hampered by the inability to determine whether differences in the outputs of redundant CPU's are due to failures or to accrued error built up by slight differences in CPU clock intervals. This study derives an analytical dynamic model of the difference between redundant CPU's due to differences in their clock intervals and uses this model with on-line parameter identification to idenitify the differences in the clock intervals. The ability of this methodology to accurately track errors due to asynchronisity generate an error signal with the effect of asynchronisity removed and this signal may be used to detect and isolate actual system failures.

Probabilistic evaluation of on-line checks in fault-tolerant multiprocessor systems

NASA Technical Reports Server (NTRS)

Nair, V. S. S.; Hoskote, Yatin V.; Abraham, Jacob A.

1992-01-01

The analysis of fault-tolerant multiprocessor systems that use concurrent error detection (CED) schemes is much more difficult than the analysis of conventional fault-tolerant architectures. Various analytical techniques have been proposed to evaluate CED schemes deterministically. However, these approaches are based on worst-case assumptions related to the failure of system components. Often, the evaluation results do not reflect the actual fault tolerance capabilities of the system. A probabilistic approach to evaluate the fault detecting and locating capabilities of on-line checks in a system is developed. The various probabilities associated with the checking schemes are identified and used in the framework of the matrix-based model. Based on these probabilistic matrices, estimates for the fault tolerance capabilities of various systems are derived analytically.

Automated AFM for small-scale and large-scale surface profiling in CMP applications

NASA Astrophysics Data System (ADS)

Zandiatashbar, Ardavan; Kim, Byong; Yoo, Young-kook; Lee, Keibock; Jo, Ahjin; Lee, Ju Suk; Cho, Sang-Joon; Park, Sang-il

2018-03-01

As the feature size is shrinking in the foundries, the need for inline high resolution surface profiling with versatile capabilities is increasing. One of the important areas of this need is chemical mechanical planarization (CMP) process. We introduce a new generation of atomic force profiler (AFP) using decoupled scanners design. The system is capable of providing small-scale profiling using XY scanner and large-scale profiling using sliding stage. Decoupled scanners design enables enhanced vision which helps minimizing the positioning error for locations of interest in case of highly polished dies. Non-Contact mode imaging is another feature of interest in this system which is used for surface roughness measurement, automatic defect review, and deep trench measurement. Examples of the measurements performed using the atomic force profiler are demonstrated.

The ontogeny of muscle structure and locomotory function in the long-finned squid Doryteuthis pealeii.

PubMed

Thompson, J T; Bartol, I K; Baksi, A E; Li, K Y; Krueger, P S

2010-04-01

Understanding the extent to which changes in muscle form and function underlie ontogenetic changes in locomotory behaviors and performance is important in understanding the evolution of musculoskeletal systems and also the ecology of different life stages. We explored ontogenetic changes in the structure, myosin heavy chain (MHC) expression and contractile properties of the circular muscles that provide power for jet locomotion in the long-finned squid Doryteuthis pealeii. The circular muscle fibers of newly hatched paralarvae had different sizes, shapes, thick filament lengths, thin:thick filament ratio, myofilament organization and sarcoplasmic reticulum (SR) distribution than those of adults. Viewed in cross section, most circular muscle cells were roughly triangular or ovoid in shape with a core of mitochondria; however, numerous muscle cells with crescent or other unusual cross-sectional shapes and muscle cells with unequal distributions of mitochondria were present in the paralarvae. The frequency of these muscle cells relative to 'normal' circular muscle cells ranged from 1:6 to 1:10 among the 19 paralarvae we surveyed. The thick filaments of the two types of circular fibers, superficial mitochondria-rich (SMR) and central mitochondria-poor (CMP), differed slightly in length among paralarvae with thick filament lengths of 0.83+/-0.15 microm and 0.71+/-0.1 microm for the SMR and CMP fibers, respectively (P 0.05; ANOVA). During ontogeny the thick filament lengths of both the CMP and SMR fibers increased significantly to 1.78+/-0.27 microm and 3.12+/-0.56 microm, respectively, in adults (P<0.0001 for both comparisons; ANOVA with Tukey's highly significant difference post hoc tests). When sectioned parallel to their long axes, the SMR and CMP fibers of both paralarvae and adults exhibited the myofilament arrangements typical of obliquely striated muscle cells but the angle of obliquity of the dense bodies was 22.8+/-2.4 deg. and 4.6+/-0.87 deg. for paralarvae and adults, respectively. There were also differences in the distribution of the anastomosing network of SR. In paralarvae, the outer and central zones of SR were well developed but the intramyoplasmic zone was greatly reduced in some cells or was scattered non-uniformly across the myoplasm. Whereas in adults the intramyoplasmic SR region was composed primarily of flattened tubules, it was composed primarily of rounded vesicles or tubules when present in the paralarvae. The ontogenetic differences in circular muscle structure were correlated with significant differences in their contractile properties. In brief tetanus at 20 degrees C, the mean unloaded shortening velocity of the paralarval circular muscle preparations was 9.1 L(0) s(-1) (where L(0) was the preparation length that generated the peak isometric stress), nearly twice that measured in other studies for the CMP fibers of adults. The mean peak isometric stress was 119+/-15 mN mm(-2) physiological cross section, nearly half that measured for the CMP fibers of adults. Reverse transcriptase-polymerase chain reaction analysis of paralarval and adult mantle samples revealed very similar expression patterns of the two known isoforms of squid MHC. The ontogenetic differences in the structure and physiology of the circular muscles may result in more rapid mantle movements during locomotion. This prediction is consistent with jet pulse durations observed in other studies, with shorter jet pulses providing hydrodynamic advantages for paralarvae.

Abrasive Particle Trajectories and Material Removal Non-Uniformity during CMP and Filtration Characteristics of CMP Slurries - A Simulation and Experimental Study

NASA Astrophysics Data System (ADS)

Rastegar, Vahid

Nanoscale finishing and planarization are integral process steps in multilevel metallization designs for integrated circuit (IC) manufacturing since it is necessary to ensure local and global surface planarization at each metal layer before depositing the next layer. Chemical mechanical planarization (CMP) has been widely recognized as the most promising technology to eliminate topographic variation and has allowed the construction of multilevel interconnection structures with a more regularly stacked sequence, resulting in better device performance [1]. Understanding fundamental of the CMP mechanisms can offer guidance to the control and optimization of the polishing processes. CMP kinematics based on slurry distribution and particle trajectories have a significant impact on MRR profiles. In this work a mathematical model to describe particle trajectories during chemical mechanical polishing was developed and extended to account for the effect of larger particles, particle location changes due to slurry dispensing and in-situ conditioning. Material removal rate (MRR) and within wafer non-uniformity (WIWNU) were determined based on the calculated particle trajectory densities. Rotary dynamics and reciprocating motion were optimized to obtain best MRR uniformity. Edge-fast MRR profile was discussed based on mechanical aspect of CMP. Using the model, we also investigated the effect of variable rotational speeds of wafer and pad, and of large particles on WIWNU and scratch growth. It was shown that the presence of even a small portion of large particles can deteriorate the WIWNU significantly and also lead to more scratches. Furthermore, it was shown that the in-situ conditioning improves the uniformity of the polished wafers. Furthermore, a combined experimental and computational study of fibrous filters for removal of larger abrasive particles from aqueous dispersions, essential to minimize defects during chemical mechanical polishing, was performed. Dilute aqueous suspensions of colloidal ceria particles, of known size distribution, were filtered at different flow rates and the filter efficiencies were measured for different particle sizes and pH, then converted to single fiber efficiencies. The particle size distributions were also measured for the influent and effluent streams. In a series of numerical simulations, the Navier-Stokes equation was solved for a single fiber using the ANSYS-FLUENT computational fluid dynamics commercial package. For dilute suspensions, the motion of the dispersed particles in the size range of 35-600 nm and zeta potential range of -50 to 50 mV was tracked in the Lagrangian reference frame including the effects of hydrodynamic drag, lift, gravity, hydrodynamic retardation, Brownian, van der Waals and electric double layer forces. The electric double layer and van der Waals forces were incorporated in the calculations by developing a user defined function. Particular attention was given to the effects of Brownian excitations, as well as the electric double layer and van der Waals forces that have been neglected in many of the previous models on the overall fiber collection efficiency for different particle sizes and charges. Moreover, the effect of flow velocity on the fiber capture efficiency and residence time was investigated. The effect of velocity on minimum collection efficiency and most penetrating particle size was investigated. It was also shown that the CFD results are in a good agreement with the experimental results.

Evaluation of the Delta-T SPN1 radiometer for the measurement of solar irradiance components

NASA Astrophysics Data System (ADS)

Estelles, Victor; Serrano, David; Segura, Sara; Wood, John; Webb, Nick; Utrillas, Maria Pilar

2016-04-01

In this study we analyse the performance of an SPN1 radiometer built by Delta-T Devices Ltd. to retrieve global solar irradiance at ground and its components (diffuse, direct) in comparison with measurements from two Kipp&Zonen CMP21 radiometers and a Kipp&Zonen CHP1 pirheliometer, mounted on an active Solys-2 suntracker at the Burjassot site (Valencia, Spain) using data acquired every minute during years 2013 - 2015. The measurement site is close to sea level (60 m a.s.l.), near the Mediterranean coast (10 km) and within the metropolitan area of Valencia City (over 1.500.000 inhabitants). The SPN1 is an inexpensive and versatile instrument for the measurement of the three components of the solar radiation without any mobile part and without any need to azimuthally align the instrument to track the sun (http://www.delta-t.co.uk). The three components of the solar radiation are estimated from a combination of measurements performed by 7 different miniature thermopiles. The SPN1 pyranometer measures the irradiance between 400 and 2700 nm, and the nominal uncertainty for the individual readings is about 8% ± 10 W/m2 (5% for the daily averages). The pyranometer Kipp&Zonen CMP21 model is a secondary standard for the measurement of broadband solar global irradiance in horizontal planes. Two ventilated CMP21 are used for the measurement of the global and diffuse irradiances. The expected total daily uncertainty of the radiometer is estimated to be 2%. The pirheliometer Kipp&Zonen CHP1 is designed for the measurement of the direct irradiance. The principles are similar to the CMP21 pyranometer. The results of the comparison show that the global irradiance from the SPN1 compares very well with the CMP21, with absolute RMSD and MBD differences below the combined uncertainties (15 W/m2 and -5.4 W/m2, respectively; relative RMSD of 3.1%). Both datasets are very well correlated, with a correlation coefficient higher than 0.997 and a slope and intercept very close to 1 and 0, respectively. The diffuse and direct irradiances do not compare as well as the global irradiance, although the deviations are below or close to the combined uncertainties. The diffuse irradiances have a RMSD and MBD of 15 W/m2 and 12 W/m2, similar to the global irradiance; the direct irradiance RMSD and MBD are 57 W/m2 and -44 W/m2. Both cases have a relative RMSD about 7.7-18%. Linearity is lower but still high (R=0.96). In conclusion, the SPN1 radiometer is a compact, robust and easy to maintain instrument that provides good results for the different solar irradiance components.

Exposure assessment and risk management of engineered nanoparticles: Investigation in semiconductor wafer processing

NASA Astrophysics Data System (ADS)

Shepard, Michele N.

Engineered nanomaterials (ENMs) are currently used in hundreds of commercial products and industrial processes, with more applications being investigated. Nanomaterials have unique properties that differ from bulk materials. While these properties may enable technological advancements, the potential risks of ENMs to people and the environment are not yet fully understood. Certain low solubility nanoparticles are more toxic than their bulk material, such that existing occupational exposure limits may not be sufficiently protective for workers. Risk assessments are currently challenging due to gaps in data on the numerous emerging materials and applications as well as method uncertainties and limitations. Chemical mechanical planarization (CMP) processes with engineered nanoparticle abrasives are used for research and commercial manufacturing applications in the semiconductor and related industries. Despite growing use, no published studies addressed occupational exposures to nanoparticles associated with CMP or risk assessment and management practices for these scenarios. Additional studies are needed to evaluate potential sources of workplace exposure or emission, as well as to help test and refine assessment methods. This research was conducted to: identify the lifecycle stages and potential exposure sources for ENMs in CMP processes; characterize worker exposure; determine recommended engineering controls and compare risk assessment models. The study included workplace air and surface sampling and an evaluation of qualitative risk banding approaches. Exposure assessment results indicated the potential for worker contact with ENMs on workplace surfaces but did not identify nanoparticles readily dispersed in air during work tasks. Some increases in respirable particle concentrations were identified, but not consistently. Measured aerosol concentrations by number and mass were well below current reference values for poorly soluble low toxicity nanoparticles. From application and evaluation of qualitative risk assessment approaches, differences in control banding models and results were identified, although output generally agreed with conclusions from air sampling as to whether an upgrade in site engineering controls was recommended. This research helped to improve understanding of potential worker exposures to ENMs in CMP processes, as well as the methods for risk assessment and management of metal oxide nanoparticles in occupational environments.

NASA Workshop on Computational Structural Mechanics 1987, part 1

NASA Technical Reports Server (NTRS)

Sykes, Nancy P. (Editor)

1989-01-01

Topics in Computational Structural Mechanics (CSM) are reviewed. CSM parallel structural methods, a transputer finite element solver, architectures for multiprocessor computers, and parallel eigenvalue extraction are among the topics discussed.

Job-mix modeling and system analysis of an aerospace multiprocessor.

NASA Technical Reports Server (NTRS)

Mallach, E. G.

1972-01-01

An aerospace guidance computer organization, consisting of multiple processors and memory units attached to a central time-multiplexed data bus, is described. A job mix for this type of computer is obtained by analysis of Apollo mission programs. Multiprocessor performance is then analyzed using: 1) queuing theory, under certain 'limiting case' assumptions; 2) Markov process methods; and 3) system simulation. Results of the analyses indicate: 1) Markov process analysis is a useful and efficient predictor of simulation results; 2) efficient job execution is not seriously impaired even when the system is so overloaded that new jobs are inordinately delayed in starting; 3) job scheduling is significant in determining system performance; and 4) a system having many slow processors may or may not perform better than a system of equal power having few fast processors, but will not perform significantly worse.

A macro-micro robot for precise force applications

NASA Technical Reports Server (NTRS)

Marzwell, Neville I.; Wang, Yulun

1993-01-01

This paper describes an 8 degree-of-freedom macro-micro robot capable of performing tasks which require accurate force control. Applications such as polishing, finishing, grinding, deburring, and cleaning are a few examples of tasks which need this capability. Currently these tasks are either performed manually or with dedicated machinery because of the lack of a flexible and cost effective tool, such as a programmable force-controlled robot. The basic design and control of the macro-micro robot is described in this paper. A modular high-performance multiprocessor control system was designed to provide sufficient compute power for executing advanced control methods. An 8 degree of freedom macro-micro mechanism was constructed to enable accurate tip forces. Control algorithms based on the impedance control method were derived, coded, and load balanced for maximum execution speed on the multiprocessor system.

Closed-form solutions of performability. [modeling of a degradable buffer/multiprocessor system

NASA Technical Reports Server (NTRS)

Meyer, J. F.

1981-01-01

Methods which yield closed form performability solutions for continuous valued variables are developed. The models are similar to those employed in performance modeling (i.e., Markovian queueing models) but are extended so as to account for variations in structure due to faults. In particular, the modeling of a degradable buffer/multiprocessor system is considered whose performance Y is the (normalized) average throughput rate realized during a bounded interval of time. To avoid known difficulties associated with exact transient solutions, an approximate decomposition of the model is employed permitting certain submodels to be solved in equilibrium. These solutions are then incorporated in a model with fewer transient states and by solving the latter, a closed form solution of the system's performability is obtained. In conclusion, some applications of this solution are discussed and illustrated, including an example of design optimization.

Parallel algorithm of VLBI software correlator under multiprocessor environment

NASA Astrophysics Data System (ADS)

Zheng, Weimin; Zhang, Dong

2007-11-01

The correlator is the key signal processing equipment of a Very Lone Baseline Interferometry (VLBI) synthetic aperture telescope. It receives the mass data collected by the VLBI observatories and produces the visibility function of the target, which can be used to spacecraft position, baseline length measurement, synthesis imaging, and other scientific applications. VLBI data correlation is a task of data intensive and computation intensive. This paper presents the algorithms of two parallel software correlators under multiprocessor environments. A near real-time correlator for spacecraft tracking adopts the pipelining and thread-parallel technology, and runs on the SMP (Symmetric Multiple Processor) servers. Another high speed prototype correlator using the mixed Pthreads and MPI (Massage Passing Interface) parallel algorithm is realized on a small Beowulf cluster platform. Both correlators have the characteristic of flexible structure, scalability, and with 10-station data correlating abilities.

HyperForest: A high performance multi-processor architecture for real-time intelligent systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garcia, P. Jr.; Rebeil, J.P.; Pollard, H.

1997-04-01

Intelligent Systems are characterized by the intensive use of computer power. The computer revolution of the last few years is what has made possible the development of the first generation of Intelligent Systems. Software for second generation Intelligent Systems will be more complex and will require more powerful computing engines in order to meet real-time constraints imposed by new robots, sensors, and applications. A multiprocessor architecture was developed that merges the advantages of message-passing and shared-memory structures: expendability and real-time compliance. The HyperForest architecture will provide an expandable real-time computing platform for computationally intensive Intelligent Systems and open the doorsmore » for the application of these systems to more complex tasks in environmental restoration and cleanup projects, flexible manufacturing systems, and DOE`s own production and disassembly activities.« less

Using parallel banded linear system solvers in generalized eigenvalue problems

NASA Technical Reports Server (NTRS)

Zhang, Hong; Moss, William F.

1993-01-01

Subspace iteration is a reliable and cost effective method for solving positive definite banded symmetric generalized eigenproblems, especially in the case of large scale problems. This paper discusses an algorithm that makes use of two parallel banded solvers in subspace iteration. A shift is introduced to decompose the banded linear systems into relatively independent subsystems and to accelerate the iterations. With this shift, an eigenproblem is mapped efficiently into the memories of a multiprocessor and a high speed-up is obtained for parallel implementations. An optimal shift is a shift that balances total computation and communication costs. Under certain conditions, we show how to estimate an optimal shift analytically using the decay rate for the inverse of a banded matrix, and how to improve this estimate. Computational results on iPSC/2 and iPSC/860 multiprocessors are presented.

Development and evaluation of a Fault-Tolerant Multiprocessor (FTMP) computer. Volume 2: FTMP software

NASA Technical Reports Server (NTRS)

Lala, J. H.; Smith, T. B., III

1983-01-01

The software developed for the Fault-Tolerant Multiprocessor (FTMP) is described. The FTMP executive is a timer-interrupt driven dispatcher that schedules iterative tasks which run at 3.125, 12.5, and 25 Hz. Major tasks which run under the executive include system configuration control, flight control, and display. The flight control task includes autopilot and autoland functions for a jet transport aircraft. System Displays include status displays of all hardware elements (processors, memories, I/O ports, buses), failure log displays showing transient and hard faults, and an autopilot display. All software is in a higher order language (AED, an ALGOL derivative). The executive is a fully distributed general purpose executive which automatically balances the load among available processor triads. Provisions for graceful performance degradation under processing overload are an integral part of the scheduling algorithms.

Blood Test: Comprehensive Metabolic Panel (CMP)

MedlinePlus

... the body's fluid levels and its acid-base balance. Normal levels of these electrolytes help keep cells in the body working as they should. Blood urea nitrogen (BUN) and creatinine , which are waste products filtered ...

Quantum Mechanics/Molecular Mechanics Study of the Sialyltransferase Reaction Mechanism.

PubMed

Hamada, Yojiro; Kanematsu, Yusuke; Tachikawa, Masanori

2016-10-11

The sialyltransferase is an enzyme that transfers the sialic acid moiety from cytidine 5'-monophospho-N-acetyl-neuraminic acid (CMP-NeuAc) to the terminal position of glycans. To elucidate the catalytic mechanism of sialyltransferase, we explored the potential energy surface along the sialic acid transfer reaction coordinates by the hybrid quantum mechanics/molecular mechanics method on the basis of the crystal structure of sialyltransferase CstII. Our calculation demonstrated that CstII employed an S N 1-like reaction mechanism via the formation of a short-lived oxocarbenium ion intermediate. The computational barrier height was 19.5 kcal/mol, which reasonably corresponded with the experimental reaction rate. We also found that two tyrosine residues (Tyr156 and Tyr162) played a vital role in stabilizing the intermediate and the transition states by quantum mechanical interaction with CMP.

The stability of a novel weakly alkaline slurry of copper interconnection CMPfor GLSI

NASA Astrophysics Data System (ADS)

Yao, Caihong; Wang, Chenwei; Niu, Xinhuan; Wang, Yan; Tian, Shengjun; Jiang, Zichao; Liu, Yuling

2018-02-01

Chemical mechanical polishing (CMP) is one of the important machining procedures of multilayered copper interconnection for GLSI, meanwhile polishing slurry is a critical factor for realizing the high polishing performance such as high planarization efficiency, low surface roughness. The effect of slurry components such as abrasive (colloidal silica), complexing agent (glycine), inhibitor (BTA) and oxidizing agent (H2O2) on the stability of the novel weakly alkaline slurry of copper interconnection CMP for GLSI was investigated in this paper. First, the synergistic and competitive relationship of them in a peroxide-based weakly alkaline slurry during the copper CMP process was studied and the stability mechanism was put forward. Then 1 wt% colloidal silica, 2.5 wt% glycine, 200 ppm BTA, 20 mL/L H2O2 had been selected as the appropriate concentration to prepare copper slurry, and using such slurry the copper blanket wafer was polished. From the variations of copper removal rate, root-mean square roughness (Sq) value with the setting time, it indicates that the working-life of the novel weakly alkaline slurry can reach more than 7 days, which satisfies the requirement of microelectronics further development. Project supported by the Major National Science and Technology Special Projects (No. 2016ZX02301003-004-007), the Professional Degree Teaching Case Foundation of Hebei Province, China (No. KCJSZ2017008), the Natural Science Foundation of Hebei Province, China (No. F2015202267), and the Natural Science Foundation of Tianjin, China (No. 16JCYBJC16100).

Isolation and Expression Profile of the Ca2+-Activated Chloride Channel-like Membrane Protein 6 Gene in Xenopus laevis

PubMed Central

Lee, Ra Mi; Ryu, Rae Hyung; Jeong, Seong Won; Oh, Soo Jin; Huang, Hue; Han, Jin Soo; Lee, Chi Ho; Lee, C. Justin; Jan, Lily Yeh

2011-01-01

To clone the first anion channel from Xenopus laevis (X. laevis), we isolated a calcium-activated chloride channel (CLCA)-like membrane protein 6 gene (CMP6) in X. laevis. As a first step in gene isolation, an expressed sequence tags database was screened to find the partial cDNA fragment. A putative partial cDNA sequence was obtained by comparison with rat CLCAs identified in our laboratory. First stranded cDNA was synthesized by reverse transcription polymerase-chain reaction (RT-PCR) using a specific primer designed for the target cDNA. Repeating the 5' and 3' rapid amplification of cDNA ends, full-length cDNA was constructed from the cDNA pool. The full-length CMP6 cDNA completed via 5'- and 3'-RACE was 2,940 bp long and had an open reading frame (ORF) of 940 amino acids. The predicted 940 polypeptides have four major transmembrane domains and showed about 50% identity with that of rat brain CLCAs in our previously published data. Semi-quantification analysis revealed that CMP6 was most abundantly expressed in small intestine, colon and liver. However, all tissues except small intestine, colon and liver had undetectable levels. This result became more credible after we did real-time PCR quantification for the target gene. In view of all CLCA studies focused on human or murine channels, this finding suggests a hypothetical protein as an ion channel, an X. laevis CLCA. PMID:21826170

Nitric oxide reversibly impairs axonal conduction in Guinea pig spinal cord.

PubMed

Ashki, Negin; Hayes, Keith C; Shi, Riyi

2006-12-01

Increased expression of the inducible and neuronal isoforms of nitric oxide synthase (NOS), and elevated concentrations of nitric oxide (NO) metabolites, are present within the central nervous system (CNS) following neurotrauma and are implicated in the pathogenesis of the accompanying neurologic deficits. We tested the hypothesis that elevated extracellular concentrations of NO introduced by the donor Spermine NONOate, induce reversible axonal conduction deficits in neurons of the guinea pig spinal cord. The compound action potential (CAP) and compound membrane potential (CMP) of excised ventral cord white matter were recorded before, during, and after bathing the tissue (30 min) in varying concentrations (0.25-3.0 mM) of Spermine NONOate. The principal results were a rapid onset, dose-dependent, reduction in amplitude of the CAP (p < 0.05) accompanied by depolarization of the CMP during NO exposure. These effects were largely reversible on washout, at low concentration of the donor (0.5 mM), but were only partially reversed at higher concentrations. Changes in the electrophysiological properties were not evident when the donor had been a priori depleted of NO. The results extend previous reports that NO induces reversible axonal conduction deficits. They provide new evidence of dissociation of the effects of NO on CAP and CMP during washout, and after prolonged exposure to the donor. They add support to the emerging concept that immune-mediated axonal conduction failure contributes to reversible neurologic deficits following neurotrauma and aid in understanding clinical phenomena such as spinal shock and neurologic recovery.

Effects of a Proteasome Inhibitor on Cardiomyocytes in a Pressure-Overload Hypertrophy Rat Model: An Animal Study.

PubMed

Kim, In-Sub; Jo, Won-Min

2017-06-01

The ubiquitin-proteasome system (UPS) is an important pathway of proteolysis in pathologic hypertrophic cardiomyocytes. We hypothesize that MG132, a proteasome inhibitor, might prevent hypertrophic cardiomyopathy (CMP) by blocking the UPS. Nuclear factor kappa-light-chain-enhancer of activated B cells (NF-κB) and androgen receptor (AR) have been reported to be mediators of CMP and heart failure. This study drew upon pathophysiologic studies and the analysis of NF-κB and AR to assess the cardioprotective effects of MG132 in a left ventricular hypertrophy (LVH) rat model. We constructed a transverse aortic constriction (TAC)-induced LVH rat model with 3 groups: sham (TAC-sham, n=10), control (TAC-cont, n=10), and MG132 administration (TAC-MG132, n=10). MG-132 (0.1 mg/kg) was injected for 4 weeks in the TAC-MG132 group. Pathophysiologic evaluations were performed and the expression of AR and NF-κB was measured in the left ventricle. Fibrosis was prevalent in the pathologic examination of the TAC-cont model, and it was reduced in the TAC-MG132 group, although not significantly. Less expression of AR, but not NF-κB, was found in the TAC-MG132 group than in the TAC-cont group (p<0.05). MG-132 was found to suppress AR in the TAC-CMP model by blocking the UPS, which reduced fibrosis. However, NF-κB expression levels were not related to UPS function.

Influence of chocolate matrix composition on cocoa flavan-3-ol bioaccessibility in vitro and bioavailability in humans.

PubMed

Neilson, Andrew P; George, Judy C; Janle, Elsa M; Mattes, Richard D; Rudolph, Ralf; Matusheski, Nathan V; Ferruzzi, Mario G

2009-10-28

Conflicting data exist regarding the influence of chocolate matrices on the bioavailability of epicatechin (EC) from cocoa. The objective of this study was to assess the bioavailability of EC from matrices varying in macronutrient composition and physical form. EC bioavailability was assessed from chocolate confections [reference dark chocolate (CDK), high sucrose (CHS), high milk protein (CMP)] and cocoa beverages [sucrose milk protein (BSMP), non-nutritive sweetener milk protein (BNMP)], in humans and in vitro. Six subjects consumed each product in a randomized crossover design, with serum EC concentrations monitored over 6 h post consumption. Areas under the serum concentration-time curve (AUC) were similar among chocolate matrices. However, AUCs were significantly increased for BSMP and BNMP (132 and 143 nM h) versus CMP (101 nM h). Peak serum concentrations (C(MAX)) were also increased for BSMP and BNMP (43 and 42 nM) compared to CDK and CMP (32 and 25 nM). Mean T(MAX) values were lower, although not statistically different, for beverages (0.9-1.1 h) versus confections (1.8-2.3 h), reflecting distinct shapes of the pharmacokinetic curves for beverages and confections. In vitro bioaccessibility and Caco-2 accumulation did not differ between treatments. These data suggest that bioavailability of cocoa flavan-3-ols is likely similar from typical commercial cocoa based foods and beverages, but that the physical form and sucrose content may influence T(MAX) and C(MAX).

Electrochemical studies of Copper, Tantalum and Tantalum Nitride surfaces in aqueous solutions for applications in chemical-mechanical and electrochemical-mechanical planarization

NASA Astrophysics Data System (ADS)

Sulyma, Christopher Michael

This report will investigate fundamental properties of materials involved in integrated circuit (IC) manufacturing. Individual materials (one at a time) are studied in different electrochemical environmental solutions to better understand the kinetics associated with the polishing process. Each system tries to simulate a real CMP environment in order to compare our findings with what is currently used in industry. To accomplish this, a variety of techniques are used. The voltage pulse modulation technique is useful for electrochemical processing of metal and alloy surfaces by utilizing faradaic reactions like electrodeposition and electrodissolution. A theoretical framework is presented in chapter 4 to facilitate quantitative analysis of experimental data (current transients) obtained in this approach. A typical application of this analysis is demonstrated for an experimental system involving electrochemical removal of copper surface layers, a relatively new process for abrasive-free electrochemical mechanical planarization of copper lines used in the fabrication of integrated circuits. Voltage pulse modulated electrodissolution of Cu in the absence of mechanical polishing is activated in an acidic solution of oxalic acid and hydrogen peroxide. The current generated by each applied voltage step shows a sharp spike, followed by a double-exponential decay, and eventually attains the rectangular shape of the potential pulses. For the second system in chapter 5, open-circuit potential measurements, cyclic voltammetry and Fourier transform impedance spectroscopy have been used to study pH dependent surface reactions of Cu and Ta rotating disc electrodes (RDEs) in aqueous solutions of succinic acid (SA, a complexing agent), hydrogen peroxide (an oxidizer), and ammonium dodecyl sulfate (ADS, a corrosion inhibitor for Cu). The surface chemistries of these systems are relevant for the development of a single-slurry approach to chemical mechanical planarization (CMP) of Cu lines and Ta barriers in the fabrication of semiconductor devices. It is shown that in non-alkaline solutions of H2O2, the SA-promoted surface complexes of Cu and Ta can potentially support chemically enhanced material removal in low-pressure CMP of surface topographies overlying fragile low-k dielectrics. ADS can suppress Cu dissolution without significantly affecting the surface chemistry of Ta. Chapter 6 discusses anodic corrosion of Ta, which is examined as a possible route to voltage induced removal of Ta for potential applications in electrochemical mechanical planarization (ECMP) of diffusion barriers. This strategy involves electro-oxidation of Ta in the presence of NO3- anions to form mechanically weak surface oxide films, followed by removal of the oxide layers by moderate mechanical abrasion. This NO3 - system is compared with a reference solution of Br -. In both electrolytes, the voltammetric currents of anodic oxidation exhibit oscillatory behaviors in the initial cycles of slow (5 mV s-1) voltage scans. The frequencies of these current oscillations are show signature attributes of localized pitting or general surface corrosion caused by Br- or NO3 -, respectively. Scanning electron microscopy, cyclic voltammetry, polarization resistance measurements, and time resolved Fourier transform impedance spectroscopy provide additional details about these corrosion mechanism. Apart from their relevance in the context of ECMP, the results also address certain fundamental aspects of pitting and general corrosions. The general protocols necessary to combine and analyze the results of D.C. and A.C. electrochemical measurements involving such valve metal corrosion systems are discussed in detail. In chapter 7 potassium salts of certain oxyanions (nitrate, sulfate and phosphate in particular) are shown to serve as effective surface-modifying agents in chemically enhanced, low-pressure chemical mechanical planarization (CMP) of Ta and TaN barrier layers for interconnect structures. The surface reactions that form the basis of this CMP strategy are investigated here in detail using the electrochemical techniques of cyclic voltammetry, open circuit potential analysis, polarization resistance measurements, and Fourier transform impedance spectroscopy. The results suggest that forming structurally weak oxide layers on the CMP samples is a key to achieving the goal of chemically controlled CMP of Ta/TaN at low down-pressures. (Abstract shortened by UMI.)

Performance and evaluation of real-time multicomputer control systems

NASA Technical Reports Server (NTRS)

Shin, K. G.

1985-01-01

Three experiments on fault tolerant multiprocessors (FTMP) were begun. They are: (1) measurement of fault latency in FTMP; (2) validation and analysis of FTMP synchronization protocols; and investigation of error propagation in FTMP.

Real-time trace ambient ammonia monitor for haze prevention

NASA Astrophysics Data System (ADS)

Nishimura, Katsumi; Sakaguchi, Yuhei; Crosson, Eric; Wahl, Edward; Rella, Chris

2007-05-01

In photolithography, haze prevention is of critical importance to integrated circuit chip manufacturers. Numerous studies have established that the presence of ammonia in the photolithography tool can cause haze to form on optical surfaces resulting in permanent damage to costly deep ultra-violet optics. Ammonia is emitted into wafer fab air by various semiconductor processes including coating steps in the track and CMP. The workers in the clean room also emit a significant amount of ammonia. Chemical filters are typically used to remove airborne contamination from critical locations but their lifetime and coverage cannot offer complete protection. Therefore, constant or periodic monitoring of airborne ammonia at parts-per-trillion (ppt) levels is critical to insure the integrity of the lithography process. Real time monitoring can insure that an accidental ammonia release in the clean room is detected before any optics is damaged. We have developed a transportable, highly accurate, highly specific, real-time trace gas monitor that detects ammonia using Cavity Ring-Down Spectroscopy (CRDS). The trace gas monitor requires no calibration gas standards, and can measure ammonia with 200 ppt sensitivity in five minutes with little or no baseline drift. In addition, the high spectral resolution of CRDS makes the analyzer less susceptible to interference from other gases when compared to other detection methods. In this paper we describe the monitor, focus on its performance, discuss the results of a careful comparison with ion chromatography (IC), and present field data measured inside the aligner and the reticule stocker at a semiconductor fab.

Design and Characterization of Next-Generation Micromirrors Fabricated in a Four-Level, Planarized Surface-Micromachined Polycrystalline Silicon Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michalicek, M.A.; Comtois, J.H.; Barron, C.C.

This paper describes the design and characterization of several types of micromirror devices to include process capabilities, device modeling, and test data resulting in deflection versus applied potential curves. These micromirror devices are the first to be fabricated in the state-of-the-art four-level planarized polysilicon process available at Sandia National Laboratories known as the Sandia Ultra-planar Multi-level MEMS Technology (SUMMiT). This enabling process permits the development of micromirror devices with near-ideal characteristics which have previously been unrealizable in standard three-layer polysilicon processes. This paper describes such characteristics as elevated address electrodes, individual address wiring beneath the device, planarized mirror surfaces usingmore » Chemical Mechanical Polishing (CMP), unique post-process metallization, and the best active surface area to date. This paper presents the design, fabrication, modeling, and characterization of several variations of Flexure-Beam (FBMD) and Axial-Rotation Micromirror Devices (ARMD). The released devices are first metallized using a standard sputtering technique relying on metallization guards and masks that are fabricated next to the devices. Such guards are shown to enable the sharing of bond pads between numerous arrays of micromirrors in order to maximize the number of on-chip test arrays. The devices are modeled and then empirically characterized using a laser interferometer setup located at the Air Force Institute of Technology (AFIT) at Wright-Patterson AFB in Dayton, Ohio. Unique design considerations for these devices and the process are also discussed.« less

The Highly Robust Electrical Interconnects and Ultrasensitive Biosensors Based on Embedded Carbon Nanotube Arrays

NASA Technical Reports Server (NTRS)

Li, Jun; Cassell, Alan; Koehne, Jessica; Chen, Hua; Ng, Hou Tee; Ye, Qi; Stevens, Ramsey; Han, Jie; Meyyappan, M.

2003-01-01

We report on our recent breakthroughs in two different applications using well-aligned carbon nanotube (CNT) arrays on Si chips, including (1) a novel processing solution for highly robust electrical interconnects in integrated circuit manufacturing, and (2) the development of ultrasensitive electrochemical DNA sensors. Both of them rely on the invention of a bottom-up fabrication scheme which includes six steps, including: (a) lithographic patterning, (b) depositing bottom conducting contacts, (c) depositing metal catalysts, (d) CNT growth by plasma enhanced chemical vapor deposition (PECVD), (e) dielectric gap-filling, and (f) chemical mechanical polishing (CMP). Such processes produce a stable planarized surface with only the open end of CNTs exposed, whch can be further processed or modified for different applications. By depositing patterned top contacts, the CNT can serve as vertical interconnects between the two conducting layers. This method is fundamentally different fiom current damascene processes and avoids problems associated with etching and filling of high aspect ratio holes at nanoscales. In addition, multiwalled CNTs (MWCNTs) are highly robust and can carry a current density of 10(exp 9) A/square centimeters without degradation. It has great potential to help extending the current Si technology. The embedded MWCNT array without the top contact layer can be also used as a nanoelectrode array in electrochemical biosensors. The cell time-constant and sensitivity can be dramatically improved. By functionalizing the tube ends with specific oligonucleotide probes, specific DNA targets can be detected with electrochemical methods down to subattomoles.

Stochastic airspace simulation tool development

DOT National Transportation Integrated Search

2009-10-01

Modeling and simulation is often used to study : the physical world when observation may not be : practical. The overall goal of a recent and ongoing : simulation tool project has been to provide a : documented, lifecycle-managed, multi-processor : c...

ARTS III/Parallel Processor Design Study

DOT National Transportation Integrated Search

1975-04-01

It was the purpose of this design study to investigate the feasibility, suitability, and cost-effectiveness of augmenting the ARTS III failsafe/failsoft multiprocessor system with a form of parallel processor to accomodate a large growth in air traff...

Evict on write, a management strategy for a prefetch unit and/or first level cache in a multiprocessor system with speculative execution

DOEpatents

Gara, Alan; Ohmacht, Martin

2014-09-16

In a multiprocessor system with at least two levels of cache, a speculative thread may run on a core processor in parallel with other threads. When the thread seeks to do a write to main memory, this access is to be written through the first level cache to the second level cache. After the write though, the corresponding line is deleted from the first level cache and/or prefetch unit, so that any further accesses to the same location in main memory have to be retrieved from the second level cache. The second level cache keeps track of multiple versions of data, where more than one speculative thread is running in parallel, while the first level cache does not have any of the versions during speculation. A switch allows choosing between modes of operation of a speculation blind first level cache.

Fault recovery characteristics of the fault tolerant multi-processor

NASA Technical Reports Server (NTRS)

Padilla, Peter A.

1990-01-01

The fault handling performance of the fault tolerant multiprocessor (FTMP) was investigated. Fault handling errors detected during fault injection experiments were characterized. In these fault injection experiments, the FTMP disabled a working unit instead of the faulted unit once every 500 faults, on the average. System design weaknesses allow active faults to exercise a part of the fault management software that handles byzantine or lying faults. It is pointed out that these weak areas in the FTMP's design increase the probability that, for any hardware fault, a good LRU (line replaceable unit) is mistakenly disabled by the fault management software. It is concluded that fault injection can help detect and analyze the behavior of a system in the ultra-reliable regime. Although fault injection testing cannot be exhaustive, it has been demonstrated that it provides a unique capability to unmask problems and to characterize the behavior of a fault-tolerant system.

Strategies for concurrent processing of complex algorithms in data driven architectures

NASA Technical Reports Server (NTRS)

Stoughton, John W.; Mielke, Roland R.

1988-01-01

The purpose is to document research to develop strategies for concurrent processing of complex algorithms in data driven architectures. The problem domain consists of decision-free algorithms having large-grained, computationally complex primitive operations. Such are often found in signal processing and control applications. The anticipated multiprocessor environment is a data flow architecture containing between two and twenty computing elements. Each computing element is a processor having local program memory, and which communicates with a common global data memory. A new graph theoretic model called ATAMM which establishes rules for relating a decomposed algorithm to its execution in a data flow architecture is presented. The ATAMM model is used to determine strategies to achieve optimum time performance and to develop a system diagnostic software tool. In addition, preliminary work on a new multiprocessor operating system based on the ATAMM specifications is described.

A robot arm simulation with a shared memory multiprocessor machine

NASA Technical Reports Server (NTRS)

Kim, Sung-Soo; Chuang, Li-Ping

1989-01-01

A parallel processing scheme for a single chain robot arm is presented for high speed computation on a shared memory multiprocessor. A recursive formulation that is derived from a virtual work form of the d'Alembert equations of motion is utilized for robot arm dynamics. A joint drive system that consists of a motor rotor and gears is included in the arm dynamics model, in order to take into account gyroscopic effects due to the spinning of the rotor. The fine grain parallelism of mechanical and control subsystem models is exploited, based on independent computation associated with bodies, joint drive systems, and controllers. Efficiency and effectiveness of the parallel scheme are demonstrated through simulations of a telerobotic manipulator arm. Two different mechanical subsystem models, i.e., with and without gyroscopic effects, are compared, to show the trade-off between efficiency and accuracy.

Strategies for concurrent processing of complex algorithms in data driven architectures

NASA Technical Reports Server (NTRS)

Stoughton, John W.; Mielke, Roland R.

1987-01-01

The results of ongoing research directed at developing a graph theoretical model for describing data and control flow associated with the execution of large grained algorithms in a spatial distributed computer environment is presented. This model is identified by the acronym ATAMM (Algorithm/Architecture Mapping Model). The purpose of such a model is to provide a basis for establishing rules for relating an algorithm to its execution in a multiprocessor environment. Specifications derived from the model lead directly to the description of a data flow architecture which is a consequence of the inherent behavior of the data and control flow described by the model. The purpose of the ATAMM based architecture is to optimize computational concurrency in the multiprocessor environment and to provide an analytical basis for performance evaluation. The ATAMM model and architecture specifications are demonstrated on a prototype system for concept validation.

Partitioning strategy for efficient nonlinear finite element dynamic analysis on multiprocessor computers

NASA Technical Reports Server (NTRS)

Noor, Ahmed K.; Peters, Jeanne M.

1989-01-01

A computational procedure is presented for the nonlinear dynamic analysis of unsymmetric structures on vector multiprocessor systems. The procedure is based on a novel hierarchical partitioning strategy in which the response of the unsymmetric and antisymmetric response vectors (modes), each obtained by using only a fraction of the degrees of freedom of the original finite element model. The three key elements of the procedure which result in high degree of concurrency throughout the solution process are: (1) mixed (or primitive variable) formulation with independent shape functions for the different fields; (2) operator splitting or restructuring of the discrete equations at each time step to delineate the symmetric and antisymmetric vectors constituting the response; and (3) two level iterative process for generating the response of the structure. An assessment is made of the effectiveness of the procedure on the CRAY X-MP/4 computers.

System architecture for asynchronous multi-processor robotic control system

NASA Technical Reports Server (NTRS)

Steele, Robert D.; Long, Mark; Backes, Paul

1993-01-01

The architecture for the Modular Telerobot Task Execution System (MOTES) as implemented in the Supervisory Telerobotics (STELER) Laboratory is described. MOTES is the software component of the remote site of a local-remote telerobotic system which is being developed for NASA for space applications, in particular Space Station Freedom applications. The system is being developed to provide control and supervised autonomous control to support both space based operation and ground-remote control with time delay. The local-remote architecture places task planning responsibilities at the local site and task execution responsibilities at the remote site. This separation allows the remote site to be designed to optimize task execution capability within a limited computational environment such as is expected in flight systems. The local site task planning system could be placed on the ground where few computational limitations are expected. MOTES is written in the Ada programming language for a multiprocessor environment.

An Evaluation of Architectural Platforms for Parallel Navier-Stokes Computations

NASA Technical Reports Server (NTRS)

Jayasimha, D. N.; Hayder, M. E.; Pillay, S. K.

1996-01-01

We study the computational, communication, and scalability characteristics of a computational fluid dynamics application, which solves the time accurate flow field of a jet using the compressible Navier-Stokes equations, on a variety of parallel architecture platforms. The platforms chosen for this study are a cluster of workstations (the LACE experimental testbed at NASA Lewis), a shared memory multiprocessor (the Cray YMP), and distributed memory multiprocessors with different topologies - the IBM SP and the Cray T3D. We investigate the impact of various networks connecting the cluster of workstations on the performance of the application and the overheads induced by popular message passing libraries used for parallelization. The work also highlights the importance of matching the memory bandwidth to the processor speed for good single processor performance. By studying the performance of an application on a variety of architectures, we are able to point out the strengths and weaknesses of each of the example computing platforms.

Parallelizing Navier-Stokes Computations on a Variety of Architectural Platforms

NASA Technical Reports Server (NTRS)

Jayasimha, D. N.; Hayder, M. E.; Pillay, S. K.

1997-01-01

We study the computational, communication, and scalability characteristics of a Computational Fluid Dynamics application, which solves the time accurate flow field of a jet using the compressible Navier-Stokes equations, on a variety of parallel architectural platforms. The platforms chosen for this study are a cluster of workstations (the LACE experimental testbed at NASA Lewis), a shared memory multiprocessor (the Cray YMP), distributed memory multiprocessors with different topologies-the IBM SP and the Cray T3D. We investigate the impact of various networks, connecting the cluster of workstations, on the performance of the application and the overheads induced by popular message passing libraries used for parallelization. The work also highlights the importance of matching the memory bandwidth to the processor speed for good single processor performance. By studying the performance of an application on a variety of architectures, we are able to point out the strengths and weaknesses of each of the example computing platforms.

The Career Motivation Process Program

ERIC Educational Resources Information Center

Garrison, Clifford; And Others

1975-01-01

Describes the Career Motivation Process (CMP) program, an experimental approach to career counseling incorporating both the "personality" approach, which centers around personal self-examination, and the "decision-making" approach, which emphasizes the collection of information about possible career options. (JG)

Nitrogen K-edge x-ray absorption near edge structure of pyrimidine-containing nucleotides in aqueous solution

NASA Astrophysics Data System (ADS)

Shimada, Hiroyuki; Minami, Hirotake; Okuizumi, Naoto; Sakuma, Ichiro; Ukai, Masatoshi; Fujii, Kentaro; Yokoya, Akinari; Fukuda, Yoshihiro; Saitoh, Yuji

2015-05-01

X-ray absorption near edge structure (XANES) was measured at energies around the N K-edge of the pyrimidine-containing nucleotides, cytidine 5'-monophosphate (CMP), 2'-deoxythymidine 5'-monophosphate (dTMP), and uridine 5'-monophosphate (UMP), in aqueous solutions and in dried films under various pH conditions. The features of resonant excitations below the N K-edge in the XANES spectra for CMP, dTMP, and UMP changed depending on the pH of the solutions. The spectral change thus observed is systematically explained by the chemical shift of the core-levels of N atoms in the nucleobase moieties caused by structural changes due to protonation or deprotonation at different proton concentrations. This interpretation is supported by the results of theoretical calculations using density functional theory for the corresponding nucleobases in the neutral and protonated or deprotonated forms.

Nitrogen K-edge x-ray absorption near edge structure of pyrimidine-containing nucleotides in aqueous solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shimada, Hiroyuki, E-mail: hshimada@cc.tuat.ac.jp; Minami, Hirotake; Okuizumi, Naoto

2015-05-07

X-ray absorption near edge structure (XANES) was measured at energies around the N K-edge of the pyrimidine-containing nucleotides, cytidine 5′-monophosphate (CMP), 2′-deoxythymidine 5′-monophosphate (dTMP), and uridine 5′-monophosphate (UMP), in aqueous solutions and in dried films under various pH conditions. The features of resonant excitations below the N K-edge in the XANES spectra for CMP, dTMP, and UMP changed depending on the pH of the solutions. The spectral change thus observed is systematically explained by the chemical shift of the core-levels of N atoms in the nucleobase moieties caused by structural changes due to protonation or deprotonation at different proton concentrations.more » This interpretation is supported by the results of theoretical calculations using density functional theory for the corresponding nucleobases in the neutral and protonated or deprotonated forms.« less

Chemical-mechanical polishing of recessed microelectromechanical devices

DOEpatents

Barron, Carole C.; Hetherington, Dale L.; Montague, Stephen

1999-01-01

A method is disclosed for micromachining recessed layers (e.g. sacrificial layers) of a microelectromechanical system (MEMS) device formed in a cavity etched into a semiconductor substrate. The method uses chemical-mechanical polishing (CMP) with a resilient polishing pad to locally planarize one or more of the recessed layers within the substrate cavity. Such local planarization using the method of the present invention is advantageous for improving the patterning of subsequently deposited layers, for eliminating mechanical interferences between functional elements (e.g. linkages) of the MEMS device, and for eliminating the formation of stringers. After the local planarization of one or more of the recessed layers, another CMP step can be provided for globally planarizing the semiconductor substrate to form a recessed MEMS device which can be integrated with electronic circuitry (e.g. CMOS, BiCMOS or bipolar circuitry) formed on the surface of the substrate.

Weighted stacking of seismic AVO data using hybrid AB semblance and local similarity

NASA Astrophysics Data System (ADS)

Deng, Pan; Chen, Yangkang; Zhang, Yu; Zhou, Hua-Wei

2016-04-01

The common-midpoint (CMP) stacking technique plays an important role in enhancing the signal-to-noise ratio (SNR) in seismic data processing and imaging. Weighted stacking is often used to improve the performance of conventional equal-weight stacking in further attenuating random noise and handling the amplitude variations in real seismic data. In this study, we propose to use a hybrid framework of combining AB semblance and a local-similarity-weighted stacking scheme. The objective is to achieve an optimal stacking of the CMP gathers with class II amplitude-variation-with-offset (AVO) polarity-reversal anomaly. The selection of high-quality near-offset reference trace is another innovation of this work because of its better preservation of useful energy. Applications to synthetic and field seismic data demonstrate a great improvement using our method to capture the true locations of weak reflections, distinguish thin-bed tuning artifacts, and effectively attenuate random noise.

Chemical-mechanical polishing of recessed microelectromechanical devices

DOEpatents

Barron, C.C.; Hetherington, D.L.; Montague, S.

1999-07-06

A method is disclosed for micromachining recessed layers (e.g. sacrificial layers) of a microelectromechanical system (MEMS) device formed in a cavity etched into a semiconductor substrate. The method uses chemical-mechanical polishing (CMP) with a resilient polishing pad to locally planarize one or more of the recessed layers within the substrate cavity. Such local planarization using the method of the present invention is advantageous for improving the patterning of subsequently deposited layers, for eliminating mechanical interferences between functional elements (e.g. linkages) of the MEMS device, and for eliminating the formation of stringers. After the local planarization of one or more of the recessed layers, another CMP step can be provided for globally planarizing the semiconductor substrate to form a recessed MEMS device which can be integrated with electronic circuitry (e.g., CMOS, BiCMOS or bipolar circuitry) formed on the surface of the substrate. 23 figs.

Conversion of post consumer waste polystyrene into a high value adsorbent and its sorptive properties for Congo Red removal from aqueous solution.

PubMed

Chaukura, Nhamo; Mamba, Bhekie B; Mishra, Shivani B

2017-05-15

Using post-consumer waste polystyrene (WPS), a conjugated microporous polymer (CMP) was synthesised and activated into a sulphonic-group carrying resin (SCMP). The surface chemistry of the materials showed a decline in both the aromatic CH and aliphatic CH 2 stretching vibrations confirming successful crosslinking. The synthesised polymers were thermally stable with decomposition temperatures above 300 °C, had surface heterogeneity, and BET surface areas of 752 and 510 m 2 /g, respectively. A distribution of pores ranging from meso- to micro-pores was comparable to other CMPs. The materials had maximum adsorption capacities of 500 and 357 mg/g for Congo Red (CR) on CMP and SCMP, respectively. Converting waste polystyrene to an adsorbent is a cost effective way of handling waste and simultaneously providing material for wastewater remediation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis and characterization of an anomeric sulfur analogue of CMP-sialic acid.

PubMed

Cohen, S B; Halcomb, R L

2000-09-22

alpha-2,3-Sialyltransferase catalyzes the transfer of sialic acid from CMP-sialic acid (1) to a lactose acceptor. An analogue of 1 was synthesized in which the anomeric oxygen atom was replaced with a sulfur atom (1S). The key step in the synthesis of 1S was a tetrazole-promoted coupling of a cytidine-5'-phosphoramidite with a glycosyl thiol of a protected sialic acid. Compounds 1 and 1S were characterized for their activity in a sialyl transfer assay. The rate of solvolysis in aqueous buffer of analogue 1S was 50-fold slower than that of 1. Analogue 1S was found to be substrate for alpha-2,3-sialyltransferase. The K(m) of 1S was just 3-fold higher than that of 1, while the k(cat) of 1S was 2 orders of magnitude lower compared to 1.

An ab initio MO study on the hydrolysis of methyl chloride with explicit consideration of 13 water molecules

NASA Astrophysics Data System (ADS)

Yamataka, Hiroshi; Aida, Misako

1998-06-01

Ab initio MO calculations (HF/3-21G, HF/6-31G, HF/6-31+G* and MP2/6-31+G*) were carried out on the hydrolysis of CH 3Cl in which up to 13 water solvent molecules were explicitly considered. For n⩾3, three important stationary points ( cmp1, TS, and cmp2) were detected in the course of the reaction. The calculations for the n=13 system at the HF/6-31+G* level reproduced the experimental activation enthalpy and the secondary deuterium kinetic isotope effect. The two reacting bond lengths in the transition state are 1.975 Å (O-C) and 2.500 Å (C-Cl), and CH 3Cl is surrounded by 13 water molecules without any apparent vacant space. The proton transfer from the attacking water to the water cluster occurs after TS is reached.

Facilitating Scholarly Writing in Academic Medicine

PubMed Central

Pololi, Linda; Knight, Sharon; Dunn, Kathleen

2004-01-01

Scholarly writing is a critical skill for faculty in academic medicine; however, few faculty receive instruction in the process. We describe the experience of 18 assistant professors who participated in a writing and faculty development program which consisted of 7 monthly 75-minute sessions embedded in a Collaborative Mentoring Program (CMP). Participants identified barriers to writing, developed personal writing strategies, had time to write, and completed monthly writing contracts. Participants provided written responses to open-ended questions about the learning experience, and at the end of the program, participants identified manuscripts submitted for publication, and completed an audiotaped interview. Analysis of qualitative data using data reduction, data display, and conclusion drawing/verification showed that this writing program facilitated the knowledge, skills, and support needed to foster writing productivity. All participants completed at least 1 scholarly manuscript by the end of the CMP. The impact on participants’ future academic productivity requires long-term follow-up. PMID:14748862

Characterizing parallel file-access patterns on a large-scale multiprocessor

NASA Technical Reports Server (NTRS)

Purakayastha, Apratim; Ellis, Carla Schlatter; Kotz, David; Nieuwejaar, Nils; Best, Michael

1994-01-01

Rapid increases in the computational speeds of multiprocessors have not been matched by corresponding performance enhancements in the I/O subsystem. To satisfy the large and growing I/O requirements of some parallel scientific applications, we need parallel file systems that can provide high-bandwidth and high-volume data transfer between the I/O subsystem and thousands of processors. Design of such high-performance parallel file systems depends on a thorough grasp of the expected workload. So far there have been no comprehensive usage studies of multiprocessor file systems. Our CHARISMA project intends to fill this void. The first results from our study involve an iPSC/860 at NASA Ames. This paper presents results from a different platform, the CM-5 at the National Center for Supercomputing Applications. The CHARISMA studies are unique because we collect information about every individual read and write request and about the entire mix of applications running on the machines. The results of our trace analysis lead to recommendations for parallel file system design. First the file system should support efficient concurrent access to many files, and I/O requests from many jobs under varying load conditions. Second, it must efficiently manage large files kept open for long periods. Third, it should expect to see small requests predominantly sequential access patterns, application-wide synchronous access, no concurrent file-sharing between jobs appreciable byte and block sharing between processes within jobs, and strong interprocess locality. Finally, the trace data suggest that node-level write caches and collective I/O request interfaces may be useful in certain environments.

The Automated Instrumentation and Monitoring System (AIMS) reference manual

NASA Technical Reports Server (NTRS)

Yan, Jerry; Hontalas, Philip; Listgarten, Sherry

1993-01-01

Whether a researcher is designing the 'next parallel programming paradigm,' another 'scalable multiprocessor' or investigating resource allocation algorithms for multiprocessors, a facility that enables parallel program execution to be captured and displayed is invaluable. Careful analysis of execution traces can help computer designers and software architects to uncover system behavior and to take advantage of specific application characteristics and hardware features. A software tool kit that facilitates performance evaluation of parallel applications on multiprocessors is described. The Automated Instrumentation and Monitoring System (AIMS) has four major software components: a source code instrumentor which automatically inserts active event recorders into the program's source code before compilation; a run time performance-monitoring library, which collects performance data; a trace file animation and analysis tool kit which reconstructs program execution from the trace file; and a trace post-processor which compensate for data collection overhead. Besides being used as prototype for developing new techniques for instrumenting, monitoring, and visualizing parallel program execution, AIMS is also being incorporated into the run-time environments of various hardware test beds to evaluate their impact on user productivity. Currently, AIMS instrumentors accept FORTRAN and C parallel programs written for Intel's NX operating system on the iPSC family of multi computers. A run-time performance-monitoring library for the iPSC/860 is included in this release. We plan to release monitors for other platforms (such as PVM and TMC's CM-5) in the near future. Performance data collected can be graphically displayed on workstations (e.g. Sun Sparc and SGI) supporting X-Windows (in particular, Xl IR5, Motif 1.1.3).

The Automated Instrumentation and Monitoring System (AIMS): Design and Architecture. 3.2

NASA Technical Reports Server (NTRS)

Yan, Jerry C.; Schmidt, Melisa; Schulbach, Cathy; Bailey, David (Technical Monitor)

1997-01-01

Whether a researcher is designing the 'next parallel programming paradigm', another 'scalable multiprocessor' or investigating resource allocation algorithms for multiprocessors, a facility that enables parallel program execution to be captured and displayed is invaluable. Careful analysis of such information can help computer and software architects to capture, and therefore, exploit behavioral variations among/within various parallel programs to take advantage of specific hardware characteristics. A software tool-set that facilitates performance evaluation of parallel applications on multiprocessors has been put together at NASA Ames Research Center under the sponsorship of NASA's High Performance Computing and Communications Program over the past five years. The Automated Instrumentation and Monitoring Systematic has three major software components: a source code instrumentor which automatically inserts active event recorders into program source code before compilation; a run-time performance monitoring library which collects performance data; and a visualization tool-set which reconstructs program execution based on the data collected. Besides being used as a prototype for developing new techniques for instrumenting, monitoring and presenting parallel program execution, AIMS is also being incorporated into the run-time environments of various hardware testbeds to evaluate their impact on user productivity. Currently, the execution of FORTRAN and C programs on the Intel Paragon and PALM workstations can be automatically instrumented and monitored. Performance data thus collected can be displayed graphically on various workstations. The process of performance tuning with AIMS will be illustrated using various NAB Parallel Benchmarks. This report includes a description of the internal architecture of AIMS and a listing of the source code.

LEM2 recruits CHMP7 for ESCRT-mediated nuclear envelope closure in fission yeast and human cells

PubMed Central

Gu, Mingyu; LaJoie, Dollie; Chen, Opal S.; von Appen, Alexander; Ladinsky, Mark S.; Redd, Michael J.; Nikolova, Linda; Bjorkman, Pamela J.; Sundquist, Wesley I.; Ullman, Katharine S.; Frost, Adam

2017-01-01

Endosomal sorting complexes required for transport III (ESCRT-III) proteins have been implicated in sealing the nuclear envelope in mammals, spindle pole body dynamics in fission yeast, and surveillance of defective nuclear pore complexes in budding yeast. Here, we report that Lem2p (LEM2), a member of the LEM (Lap2-Emerin-Man1) family of inner nuclear membrane proteins, and the ESCRT-II/ESCRT-III hybrid protein Cmp7p (CHMP7), work together to recruit additional ESCRT-III proteins to holes in the nuclear membrane. In Schizosaccharomyces pombe, deletion of the ATPase vps4 leads to severe defects in nuclear morphology and integrity. These phenotypes are suppressed by loss-of-function mutations that arise spontaneously in lem2 or cmp7, implying that these proteins may function upstream in the same pathway. Building on these genetic interactions, we explored the role of LEM2 during nuclear envelope reformation in human cells. We found that CHMP7 and LEM2 enrich at the same region of the chromatin disk periphery during this window of cell division and that CHMP7 can bind directly to the C-terminal domain of LEM2 in vitro. We further found that, during nuclear envelope formation, recruitment of the ESCRT factors CHMP7, CHMP2A, and IST1/CHMP8 all depend on LEM2 in human cells. We conclude that Lem2p/LEM2 is a conserved nuclear site-specific adaptor that recruits Cmp7p/CHMP7 and downstream ESCRT factors to the nuclear envelope. PMID:28242692

The role of hydroxo-bridged dinuclear species and the influence of "innocent" buffers in the reactivity of cis-[Co(III)(cyclen)(H₂O)₂]³⁺ and [Co(III)(tren)(H₂O)₂]³⁺ complexes with biologically relevant ligands at physiological pH.

PubMed

Basallote, Manuel G; Martínez, Manuel; Vázquez, Marta

2014-07-28

In view of the relevance of the reactivity of inert tetraamine Co(III) complexes having two substitutionally active cis positions capable of interact with biologically relevant ligands, the study of the reaction of cis-[Co(cyclen)(H2O)2](3+) and [Co(tren)(H2O)2](3+) with chlorides, inorganic phosphate and 5'-CMP (5'-cytidinemonophosphate) has been pursued at physiological pH. The results indicate that, in addition to the actuation of the expected labilising conjugate-base mechanism, the formation of mono and inert bis hydroxo-bridged species is relevant for understanding their speciation and reactivity. The reactivity pattern observed also indicates the key role played by the "innocent" buffers frequently used in most in vitro studies, which can make the results unreliable in many cases. The differences between the reactivity of inorganic and biologically relevant phosphates has also been found to be remarkable, with outer-sphere hydrogen bonding interactions being a dominant factor for the process. While for the inorganic phosphate substitution process the formation of μ-η(2)-OPO2O represents the termination of the reactivity monitored, for 5'-CMP only the formation of η(1)-OPO3 species is observed, which evolve with time to the final dead-end bis hydroxo-bridged complexes. The promoted hydrolysis of the 5'-CMP phosphate has not been observed in any of the processes studied.

Myocardial oedema as the sole marker of acute injury in Takotsubo cardiomyopathy: a cardiovascular magnetic resonance (CMR) study.

PubMed

Iacucci, Ilaria; Carbone, Iacopo; Cannavale, Giuseppe; Conti, Bettina; Iampieri, Ilaria; Rosati, Riccardo; Sardella, Gennaro; Frustaci, Andrea; Fedele, Francesco; Catalano, Carlo; Francone, Marco

2013-12-01

The main hallmark of Takotsubo cardiomyopathy (TT-CMP) is transient ischaemia, with completely reversible regional contractile dysfunction, which involves the mid-apical segments and shows no angiographic signs of coronary artery disease (CAD). The acute and reversible myocardial injury suggests that tissue oedema may be an important marker of disease. Seventeen patients with a clinical and angiographic diagnosis of TT-CMP underwent cardiovascular magnetic resonance (CMR) imaging in the acute phase and at follow-up after 4 months. A standard acquisition protocol including turbo spin echo (TSE) T2-weighted short-tau inversion-recovery (T2 STIR), steady-state free-precession cine (SSFP cine) and lateenhancement (LE) imaging after gadolinium benzyloxypropionic tetraacetic acid (Gd-BOPTA) administration was performed. All images were analysed, and data on oedema and LE were correlated with regional dysfunction and histological findings from endomyocardial biopsy (EMB) where available. In all patients, T2 STIR images showed a diffuse homogeneous hyperintensity that extended to all mid-apical segments and perfectly matched the area of regional dysfunction, reflecting tissue oedema. In the five patients who underwent EMB, histology confirmed the massive interstitial oedema associated with typical contraction-band necrosis. No cases of LE were observed. At follow-up, complete regression of oedema was observed in all cases, with significant recovery of regional and global left ventricular (LV) function (ejection fraction from 48.7% to 59.8%). Myocardial oedema on CMR is a characteristic feature of acute TT-CMP, which reflects acute inflammation and acute myocardial injury. It could therefore be used as a specific marker of disease severity.

Enzymatic Characterization of AMP Phosphorylase and Ribose-1,5-Bisphosphate Isomerase Functioning in an Archaeal AMP Metabolic Pathway

PubMed Central

Aono, Riku; Sato, Takaaki; Yano, Ayumu; Yoshida, Shosuke; Nishitani, Yuichi; Miki, Kunio; Imanaka, Tadayuki

2012-01-01

AMP phosphorylase (AMPpase), ribose-1,5-bisphosphate (R15P) isomerase, and type III ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco) have been proposed to constitute a novel pathway involved in AMP metabolism in the Archaea. Here we performed a biochemical examination of AMPpase and R15P isomerase from Thermococcus kodakarensis. R15P isomerase was specific for the α-anomer of R15P and did not recognize other sugar compounds. We observed that activity was extremely low with the substrate R15P alone but was dramatically activated in the presence of AMP. Using AMP-activated R15P isomerase, we reevaluated the substrate specificity of AMPpase. AMPpase exhibited phosphorylase activity toward CMP and UMP in addition to AMP. The [S]-v plot (plot of velocity versus substrate concentration) of the enzyme toward AMP was sigmoidal, with an increase in activity observed at concentrations higher than approximately 3 mM. The behavior of the two enzymes toward AMP indicates that the pathway is intrinsically designed to prevent excess degradation of intracellular AMP. We further examined the formation of 3-phosphoglycerate from AMP, CMP, and UMP in T. kodakarensis cell extracts. 3-Phosphoglycerate generation was observed from AMP alone, and from CMP or UMP in the presence of dAMP, which also activates R15P isomerase. 3-Phosphoglycerate was not formed when 2-carboxyarabinitol 1,5-bisphosphate, a Rubisco inhibitor, was added. The results strongly suggest that these enzymes are actually involved in the conversion of nucleoside monophosphates to 3-phosphoglycerate in T. kodakarensis. PMID:23065974

Interactions of 1,12-diamino-4,9-dioxadodecane (OSpm) and Cu(II) ions with pyrimidine and purine nucleotides: adenosine-5'-monophosphate (AMP) and cytidine-5'-monophosphate (CMP).

PubMed

Lomozik, L; Gasowska, A; Krzysko, G

2006-11-01

The interactions of Cu(II) ions with adenosine-5'-monophosphate (AMP), cytidine-5'-monophosphate (CMP) and 1,12-diamino-4,9-dioxadodecane (OSpm) were studied. A potentiometric method was applied to determine the composition and stability constants of complexes formed, while the mode of interactions was analysed by spectral methods (ultraviolet and visible spectroscopy (UV-Vis), electron paramagnetic resonance (EPR), (13)C NMR, (31)P NMR). In metal-free systems, molecular complexes nucleotide-polyamine (NMP)H(x)(OSpm) were formed. The endocyclic nitrogen atoms of the purine ring N(1), N(7), the nitrogen atom of the pyrimidine ring N(3), the oxygen atoms of the phosphate group of the nucleotide and the protonated nitrogen atoms of the polyamine were the reaction centres. The mode of interaction of the metal ion with OSpm and the nucleotides (AMP or CMP) in the coordination compounds was established. In the system Cu(II)/OSpm the dinuclear complex Cu(2)(OSpm) forms, while in the ternary systems Cu(II)/nucleotide/OSpm the species type MH(x)LL' and MLL' appear. In the MH(x)LL' type species, the main centres of copper (II) ion binding in the nucleotide are the phosphate groups. The protonated amino groups of OSpm are involved in non-covalent interaction with the nitrogen atoms N(1), N(7) or N(3) of the purine or pyrimidine ring, whereas at higher pH, deprotonated nitrogen atoms of polyamine are engaged in metallation in MLL' species.

Hierachical assembly of collagen mimetic peptides into biofunctional materials

NASA Astrophysics Data System (ADS)

Gleaton, Jeremy W.

Collagen is a remarkably strong and prevalent protein distributed throughout nature and as such, collagen is an ideal material for a variety of medical applications. Research efforts for the development of synthetic collagen biomaterials is an area of rapid growth. Here we present two methods for the assembly of collagen mimetic peptides (CMPs). The initial approach prompts assembly of CMPs which contain modifications for metal ion-triggered assembly. Hierarchical assembly into triple helices, followed by formation of disks via hydrophobic interactions has been demonstrated. Metal-ion mediated assembly of these disks, using iron (II)-bipyrdine interactions, has been shown to form micron-sized cages. The nature of the final structures that form depends on the number of bipyridine moieties incorporated into the CMP. These hollow spheres encapsulate a range of molecular weight fluorescently labeled dextrans. Furthermore, they demonstrate a time dependent release of contents under a variety of thermal conditions. The second approach assembles CMPs via the copper-catalyzed alkyne-azide cycloaddition (CuAAC) and the strain-promoted alkyne-azide cycloaddition (SPAAC) reactions. CMPs that incorporate the unnatural amino acids L-propargylglycine and L-azidolysine form triple helices and demonstrate higher order assembly when reacted via CuAAC. Reaction of the alkyne/azide modified CMPs under CuAAC conditions was found to produce an crosslinked 3-dimensional network. Moreover, we demonstrate that polymers, such as, PEG, can be reacted with alkyne and azide CMP triple helices via CuAAC and SPAAC. This designed covalent CMP chemistry allows for high flexibility in integrating various chemical cues, such as cell growth and differentiation within the higher order structures.

Synchronizing Data-Bus Messages

NASA Technical Reports Server (NTRS)

Harris, L. H.

1985-01-01

Adapter allows communications among as many as 30 data processors without central bus controller. Adapter improves reliability of multiprocessor system by eliminating point of failure that causes entire system to fail. Scheme prevents data collisions and eliminates nonessential polling, thereby reducing power consumption.