Optimization of buffer injection for the effective bioremediation of chlorinated solvents in aquifers

NASA Astrophysics Data System (ADS)

Brovelli, A.; Robinson, C.; Barry, A.; Kouznetsova, I.; Gerhard, J.

2008-12-01

Various techniques have been proposed to enhance biologically-mediated reductive dechlorination of chlorinated solvents in the subsurface, including the addition of fermentable organic substrate for the generation of H2 as an electron donor. One rate-limiting factor for enhanced dechlorination is the pore fluid pH. Organic acids and H+ ions accumulate in dechlorination zones, generating unfavorable conditions for microbial activity (pH < 6.5). The pH variation is a nonlinear function of the amount of reduced chlorinated solvents, and is affected by the organic material fermented, the chemical composition of the pore fluid and the soil's buffering capacity. Consequently, in some cases enhanced remediation schemes rely on buffer injection (e.g., bicarbonate) to alleviate this problem, particularly in the presence of solvent nonaqueous phase liquid (NAPL) source zones. However, the amount of buffer required - particularly in complex, evolving biogeochemical environments - is not well understood. To investigate this question, this work builds upon a geochemical numerical model (Robinson et al., Science of the Total Environment, submitted), which computes the amount of additional buffer required to maintain the pH at a level suitable for bacterial activity for batch systems. The batch model was coupled to a groundwater flow/solute transport/chemical reaction simulator to permit buffer optimization computations within the context of flowing systems exhibiting heterogeneous hydraulic, physical and chemical properties. A suite of simulations was conducted in which buffer optimization was examined within the bounds of the minimum concentration necessary to sustain a pH favorable to microbial activity and the maximum concentration to avoid excessively high pH values (also not suitable to bacterial activity) and mineral precipitation (e.g., calcite, which may lead to pore-clogging). These simulations include an examination of the sensitivity of this buffer concentration range to aquifer heterogeneity and groundwater velocity. This work is part of SABRE (Source Area BioREmediation), a collaborative international research project that aims to evaluate and improve enhanced bioremediation of chlorinated solvent source zones. In this context, numerical simulations are supporting the upscaling of the technique, including identifying the most appropriate buffer injection strategies for field applications

METRICS OF PERFORMANCE FOR THE SABRE MICROCOSM STUDY (ABSTRACT ONLY)

EPA Science Inventory

The SABRE (Source Area BioREmediation) project will evaluate accelerated anaerobic bioremediation of chlorinated solvents in areas of high concentration, such as DNAPL source areas. In preparation for a field scale pilot test, a laboratory microcosm study was conducted to provide...

CHARACTERIZING THE MICROBIAL COMMUNITY IN SABRE MICROCOSM STUDIES (ABSTRACT ONLY)

EPA Science Inventory

The SABRE (Source Area BioREmediation) project will evaluate accelerated anaerobic bioremediation of chlorinated solvents in areas of high concentration, such as DNAPL source areas. In preparation for a field scale pilot test, laboratory microcosm and column studies were conducte...

NON-BIOLOGICAL REACTIONS MAY BE AN IMPORTANT MECHANISM FOR NATURAL ATTENUATION OF CHLORINATED SOLVENTS

EPA Science Inventory

The role of non-biological transformation of chlorinated solvents was not considered in the U.S. EPA Technical Protocol for Evaluating Natural Attenuation of Chlorinated Solvents in Ground Water. This deficiency became very apparent when U.S. EPA conducted a beta test of the Pro...

Characterization and Remediation of Chlorinated Volatile Organic Contaminants in the Vadose Zone: An Overview of Issues and Approaches

PubMed Central

Brusseau, Mark L.; Carroll, Kenneth C.; Truex, Michael J.; Becker, David J.

2014-01-01

Contamination of vadose-zone systems by chlorinated solvents is widespread, and poses significant potential risk to human health through impacts on groundwater quality and vapor intrusion. Soil vapor extraction (SVE) is the presumptive remedy for such contamination, and has been used successfully for innumerable sites. However, SVE operations typically exhibit reduced mass-removal effectiveness at some point due to the impact of poorly accessible contaminant mass and associated mass-transfer limitations. Assessment of SVE performance and closure is currently based on characterizing contaminant mass discharge associated with the vadose-zone source, and its impact on groundwater or vapor intrusion. These issues are addressed in this overview, with a focus on summarizing recent advances in our understanding of the transport, characterization, and remediation of chlorinated solvents in the vadose zone. The evolution of contaminant distribution over time and the associated impacts on remediation efficiency will be discussed, as will the potential impact of persistent sources on groundwater quality and vapor intrusion. In addition, alternative methods for site characterization and remediation will be addressed. PMID:25383058

Grape pomace compost harbors organohalide-respiring Dehalogenimonas species with novel reductive dehalogenase genes

DOE PAGES

Yang, Yi; Higgins, Steven A.; Yan, Jun; ...

2017-08-15

Here, organohalide-respiring bacteria play key roles in the natural chlorine cycle; however, most of the current knowledge is based on cultures from contaminated environments. We demonstrate that grape pomace compost without prior exposure to chlorinated solvents harbors a Dehalogenimonas ( Dhgm) species capable of using chlorinated ethenes, including the human carcinogen and common groundwater pollutant vinyl chloride (VC) as electron acceptors. Grape pomace microcosms and derived solid-free enrichment cultures were able to dechlorinate trichloroethene (TCE) to less chlorinated daughter products including ethene. 16S rRNA gene amplicon and qPCR analyses revealed the predominance of Dhgm sequences, but no Dehalococcoides mccartyi (more » Dhc) biomarker genes were detected. The enumeration of Dhgm 16S rRNA genes demonstrated VC-dependent growth, and 6.55 ± 0.64 x 10 8 cells were produced per µmole of chloride released. Metagenome sequencing enabled the assembly of a Dhgm draft genome, and 52 putative reductive dehalogenase (RDase) genes were identified. Proteomic workflows identified a putative VC RDase with 49% and 56.1% amino acid similarity to the known VC RDases VcrA and BvcA, respectively. A survey of 1,173 groundwater samples collected from 111 chlorinated solvent-contaminated sites revealed that Dhgm 16S rRNA genes were frequently detected and outnumbered Dhc in 65% of the samples. Dhgm may be more relevant contributors to chlorinated solvent reductive dechlorination in contaminated aquifers than is currently recognized, and non-polluted environments are a source of strictly organohalide-respiring bacteria with novel RDase genes.« less

Grape pomace compost harbors organohalide-respiring Dehalogenimonas species with novel reductive dehalogenase genes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Yi; Higgins, Steven A.; Yan, Jun

Here, organohalide-respiring bacteria play key roles in the natural chlorine cycle; however, most of the current knowledge is based on cultures from contaminated environments. We demonstrate that grape pomace compost without prior exposure to chlorinated solvents harbors a Dehalogenimonas ( Dhgm) species capable of using chlorinated ethenes, including the human carcinogen and common groundwater pollutant vinyl chloride (VC) as electron acceptors. Grape pomace microcosms and derived solid-free enrichment cultures were able to dechlorinate trichloroethene (TCE) to less chlorinated daughter products including ethene. 16S rRNA gene amplicon and qPCR analyses revealed the predominance of Dhgm sequences, but no Dehalococcoides mccartyi (more » Dhc) biomarker genes were detected. The enumeration of Dhgm 16S rRNA genes demonstrated VC-dependent growth, and 6.55 ± 0.64 x 10 8 cells were produced per µmole of chloride released. Metagenome sequencing enabled the assembly of a Dhgm draft genome, and 52 putative reductive dehalogenase (RDase) genes were identified. Proteomic workflows identified a putative VC RDase with 49% and 56.1% amino acid similarity to the known VC RDases VcrA and BvcA, respectively. A survey of 1,173 groundwater samples collected from 111 chlorinated solvent-contaminated sites revealed that Dhgm 16S rRNA genes were frequently detected and outnumbered Dhc in 65% of the samples. Dhgm may be more relevant contributors to chlorinated solvent reductive dechlorination in contaminated aquifers than is currently recognized, and non-polluted environments are a source of strictly organohalide-respiring bacteria with novel RDase genes.« less

Characterizing The Microbial Community In A TCE DNAPL Site: SABRE Column And Field Studies

EPA Science Inventory

The SABRE (Source Area BioREmediation) project is evaluating accelerated anaerobic bioremediation of chlorinated solvents in areas of high concentration, such as DNAPL source areas. In support of a field scale pilot test, column studies were conducted to design the system and ob...

Spatial And Temporal Distribution Of Microbial Communities In A TCE DNAPL Site: SABRE Field Studies

EPA Science Inventory

The SABRE (Source Area BioREmediation) project was conducted to evaluate accelerated anaerobic bioremediation of chlorinated solvents in areas of high concentration, such as DNAPL source areas. To study performance of this technology, a test cell was constructed with a longitudi...

COMPLETE NATURAL ATTENUATION OF A PCE AND TCE PLUME AFTER SOURCE REMOVAL

EPA Science Inventory

Disposal of the chlorinated solvents PCE and TCE at the Twin Cities Army Ammunition Plant (TCAAP) resulted in the contamination of groundwater in a shallow, unconsolidated sand aquifer. The resulting plume had moved over 1000 feet from the disposal source area and had impacted p...

Biodegradation of Chlorinated Solvents: Reactions near DNAPL and Enzyme Function

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCarty, P. L.; Spormann, Alfred M.; Criddle, Craig, S.

Chlorinated solvents are among the most widespread groundwater contaminants in the country, contamination which is also among the most difficult and expensive for remediation. These solvents are biodegradable in the absence of oxygen, but this biodegradation requires both a food source for the organisms (electron donor) and the presence of chlorinated solvent biodegrading organisms. These two requirements are present naturally at some contamination sites, leading to natural attenuation of the solvents. If one or both requirements are absent, then engineered bioremediation either through addition of an external electron donor or through bioaugmentation with appropriate microorganisms, or both, may be usedmore » for site remediation. The most difficult case for cleanup is when a large residual of undissolved chlorinated solvents are present, residing as dense -non-aqueous-phase- liquid ( DNAPL). A major focus of this study was on the potential for biodegradation of the solvents when pre sent as DNAPL where concentrations are very high and potential for toxicity to microorganisms exist. Another focus was on a better understanding of the biological mechanisms involved in chlorinated solvent biodegradation . These studies were directed towards the chlorinated solvents, trichloroethene (TCE), tetrachloroethene or perchloroethene (PCE), and carbon tetrachloride (CT). The potential for biodegradation of TCE and PCE DNAPL was clearly demonstrated in this research. From column soil studies and batch studies we found there to be a clear advantage in focusing efforts at bioremediation near the DNAPL. Here, chlorinated solvent concentrations are the highest, both because of more favorable reaction kinetics and because such high solvent concentrations are toxic to microorganisms, such as methanogens, which compete with dehalogenators for the electron donor. Additionally, biodegradation near a PCE DNAPL results in an enhanced dissolution rate for the chlorinated solvent, by factors of three to five times, leading to a more rapid clean-up of the DNAPL zone. The most favored electron donor to add is one which partitions well with the chlorinated solvent or can be concentrated near it. Unfortunately, an ideal electron donor, such as vegetable oil, is difficult to introduce and mix with DNAPL in the ground, doing this properly remains an engineering challenge. Numerical model studies have indicated that several factors may significantly influence the rate and extent of enhancement, including the inhibitory effects of PCE and cDCE, the level of ED concentration, DNAPL configuration, and competition for ED. Such factors need to be considered when contemplating engineered DNAPL bioremediation. Pseudomonas stuzeri KC is an organism that transforms CT to carbon dioxide and chloride without the formation of the hazardous intermediate, chloroform. This is accomplished by production and secretion of a molecule called PDTC. This study was direct ed towards determining how PDTC works. Cu (II) at a ratio of 1:1 Cu to PDTC was found to result in the most rapid CT transformation, confirming that the PDTC-Cu complex is both a reactant and a catalyst in CT transformation. CT degradation requires that the PDTC be in a reduced form, which is generated by contact with cell components. Fe(II) inhibits CT transformation by PDTC. Studies indicated that this inhibition is enhanced by some compound or factor in the supernatant with molecular weight greater than 10,000 Da. We have made progress in determining what this factor might be, but have not yet been able to identify it. In related studies, we found that CT transformation by another organism, Shewanella oneidensis MR1, also involves an excreted factor, but this factor is different from PDTC and results in chloroform transformation as an intermediate. Our studies have indicated that this factor is similar to vitamin K2, and we have also confirmed that vitamin K2 does transform C T into chloroform.« less

Aqueous alternatives for metal and composite cleaning

NASA Technical Reports Server (NTRS)

Quitmeyer, Joann

1994-01-01

For many years the metalworking industry has cleaned metal and composite substrates with chlorinated solvents. Recently, however, health and disposal related environmental concerns have increased regarding chlorinated solvents, including 1,1,1-trichloroethane, trichloroethylene, methylene chloride, or Freon'. World leaders have instituted a production ban of certain ozone depleting chlorofluorocarbons (CFC's) by 1996. The Occupational Safety and Health Administration (OSHA) has instituted worker vapor exposure limitations for virtually all of the solvents used in solvent-based cleaners. In addition, the United States Environmental Protection Agency (EPA) has defined nearly all solvent-based cleaners as 'hazardous'. Cradle to grave waste responsibility is another reason manufacturers are trying to replace chlorinated solvents in their cleaning processes. Because of these factors, there now is a world wide effort to reduce and/or eliminate the use of chlorinated solvents for industrial cleaning. Waterbased cleaners are among the alternatives being offered to the industry. New technology alkaline cleaners are now available that can be used instead of chlorinated solvents in many cleaning processes. These waterbased cleaners reduce the release of volatile organic compounds (VOC's) by as much as 99 percent. (The definition and method of calculation of VOC's now varies from region to region.) Hazardous waste generation can also be significantly reduced or eliminated with new aqueous technology. This in turn can ease worker exposure restrictions and positively impact the environment. This paper compares the chemical and physical properties of this aqueous cleaners versus chlorinated solvents.

Guidelines for the Selection of Chemical Protective Clothing. Volume 2. Technical and Reference Manual.

DTIC Science & Technology

1987-02-01

Handler’s Suit for Protection from Chlorine Trifluoride and Elemental Fluorine Technical Report AFRPL-TR-71-44 (August 1971) NTIS AD731556 199 Masterman’s...Protective Clothing for Chlorine , Edition 1 Chlorine Institute Pamphlet 65, The Chlorine Institute, Inc. New York, New York, (June 1978) 15 Anon...Chemical Company Selection of Gloves for Use With Chlorinated Solvents Chlorinated Solvents Information Midland, Michigan 48640 101 Duffy, R.M., A.R.Beer

Unintentional contaminant transfer from groundwater to the vadose zone during source zone remediation of volatile organic compounds.

PubMed

Chong, Andrea D; Mayer, K Ulrich

2017-09-01

Historical heavy use of chlorinated solvents in conjunction with improper disposal practices and accidental releases has resulted in widespread contamination of soils and groundwater in North America and worldwide. As a result, remediation of chlorinated solvents is required at many sites. For source zone treatment, common remediation strategies include in-situ chemical oxidation (ISCO) using potassium or sodium permanganate, and the enhancement of biodegradation by primary substrate addition. It is well known that these remediation methods tend to generate gas (carbon dioxide (CO 2 ) in the case of ISCO using permanganate, CO 2 and methane (CH 4 ) in the case of bioremediation). Vigorous gas generation in the presence of chlorinated solvents, which are categorized as volatile organic contaminants (VOCs), may cause gas exsolution, ebullition and stripping of the contaminants from the treatment zone. This process may lead to unintentional 'compartment transfer', whereby VOCs are transported away from the contaminated zone into overlying clean sediments and into the vadose zone. To this extent, benchtop column experiments were conducted to quantify the effect of gas generation during remediation of the common chlorinated solvent trichloroethylene (TCE/C 2 Cl 3 H). Both ISCO and enhanced bioremediation were considered as treatment methods. Results show that gas exsolution and ebullition occurs for both remediation technologies. Facilitated by ebullition, TCE was transported from the source zone into overlying clean groundwater and was subsequently released into the column headspace. For the case of enhanced bioremediation, the intermediate degradation product vinyl chloride (VC) was also stripped from the treatment zone. The concentrations measured in the headspace of the columns (TCE ∼300ppm in the ISCO column, TCE ∼500ppm and VC ∼1380ppm in the bioremediation column) indicate that substantial transfer of VOCs to the vadose zone is possible. These findings provide direct evidence for the unintended spreading of contaminants as a result of remediation efforts, which can, under some circumstances, result in enhanced risks for soil vapour intrusion. Copyright © 2017 Elsevier B.V. All rights reserved.

Remediation Evaluation Model for Chlorinated Solvents (REMChlor)

EPA Science Inventory

A new analytical solution has been developed for simulating the transient effects of groundwater source and plume remediation. This development was performed as part of a Strategic Environmental Research and Development Program (SERDP) research project, which was a joint effort ...

Biodegradation of Chlorinated Solvents: Reactions near DNAPL and Enzyme Function

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCarty, Perry L.; Spormann, Alfred M.; Criddle, Craig S.

The anaerobic biodegradation of chlorinated solvents is of great interest both for natural attenuation and for engineered remediation of these hazardous contaminants in groundwater. Compounds to be studied are carbon tetrachloride (CT) and the chlorinated ethenes, tetrachloroethene (PCE), trichloroethene (TCE) cis-1,2-dichloroethene (cDCE), and vinyl chloride (VC). The chlorinated solvents often are present as dense non-aqueous-phase liquids (DNAPLs), which are difficult to remove. Biodegradation of DNAPLs was previously thought not possible because of toxicity, but recent evidence indicates that under the right conditions, biodegradation is possible. Anaerobic biodegradation of DNAPLs is the major subject of this research. The specific objectives ofmore » this multi-investigator effort are: (1) Evaluate the potential for chlorinated solvent biodegradation near DNAPLs, (2) Provide a molecular understanding of the biological mechanisms involved, (3) Determine cellular components involved in carbon tetrachloride transformation by Pseudomonas stutzeri strain KC without chloroform formation.« less

EVALUATION OF THE ROLE OF DEHALOCOCCOIDES ORGANISMS IN THE NATURAL ATTENUATION OF CHLORINATED ETHYLENES IN GROUNDWATER

EPA Science Inventory

At most hazardous waste sites where monitored natural attenuation (MNA) of chlorinated solvents in ground water is successful as a remedy, the chlorinated solvents are biologically degraded to harmless end products such as ethylene or ethane. Many organisms can degrade chlorinat...

Biodegradation Kinetics of 1,4-Dioxane in Chlorinated Solvent Mixtures.

PubMed

Zhang, Shu; Gedalanga, Phillip B; Mahendra, Shaily

2016-09-06

This study investigated the impacts of individual chlorinated solvents and their mixtures on aerobic 1,4-dioxane biodegradation by Pseudonocardia dioxanivorans CB1190. The established association of these co-occurring compounds suggests important considerations for their respective biodegradation processes. Our kinetics and mechanistic studies demonstrated that individual solvents inhibited biodegradation of 1,4-dioxane in the following order: 1,1-dichloroethene (1,1-DCE) > cis-1,2-diochloroethene (cDCE) > trichloroethene (TCE) > 1,1,1-trichloroethane (TCA). The presence of 5 mg L(-1) 1,1-DCE completely inhibited 1,4-dioxane biodegradation. Subsequently, we determined that 1,1-DCE was the strongest inhibitor of 1,4-dioxane biodegradation by bacterial pure cultures exposed to chlorinated solvent mixtures as well as in environmental samples collected from a site contaminated with chlorinated solvents and 1,4-dioxane. Inhibition of 1,4-dioxane biodegradation rates by chlorinated solvents was attributed to delayed ATP production and down-regulation of both 1,4-dioxane monooxygenase (dxmB) and aldehyde dehydrogenase (aldH) genes. Moreover, increasing concentrations of 1,1-DCE and cis-1,2-DCE to 50 mg L(-1) respectively increased 5.0-fold and 3.5-fold the expression of the uspA gene encoding a universal stress protein. In situ natural attenuation or enhanced biodegradation of 1,4-dioxane is being considered for contaminated groundwater and industrial wastewater, so these results will have implications for selecting 1,4-dioxane bioremediation strategies at sites where chlorinated solvents are present as co-contaminants.

CHLORINATED SOLVENT PLUME CONTROL

EPA Science Inventory

This lecture will cover recent success in controlling and assessing the treatment of shallow ground water plumes of chlorinated solvents, other halogenated organic compounds, and methyl tert-butyl ether (MTBE).

Oxidative Gelation of Solvent-Accessible Arabinoxylans is the Predominant Consequence of Extensive Chlorination of Soft Wheat Flour

USDA-ARS?s Scientific Manuscript database

Solvent retention capacity (SRC) and Bostwick flow were used to explore the effects of milling yield, extent of chlorination, and flour particle size on cake flour functionality and batter viscosity. The effects of the extent of chlorination were dramatic, but milling yield and additional milling t...

Guidance Protocol: Application of Nucleic Acid-Based Tools for Monitoring Monitored Natural Attenuation (MNA), Biostimulation, and Bioaugmentation at Chlorinated Solvent Sites

DTIC Science & Technology

2011-02-01

Reductive dechlorination is a promising process for biodegradation of chlorinated solvents. The successful field evaluation and implementation of the...population. These specialized bacteria use the chlorinated ethenes as electron acceptors and gain energy for growth from the reductive...This guidance protocol addresses the use of MBTs to quantitatively assess the Dhc population at chlorinated ethene sites and aims at providing

EVALUATING THE POTENTIAL FOR CHLORINATED SOLVENT DEGRADATION FROM HYDROGEN CONCENTRATIONS

EPA Science Inventory

Long-term monitoring of a large trichioroethylene (TCE) and 1,1,1-trichloroethane (TCA) ground water plume in Minnesota indicated that these contaminants attenuated with distance from the source. Mathematical modelling indicated that sufficient time had passed for the plume to fu...

Interactions Between Chlorinated Waste Solvents and Clay Minerals in Low Permeability Subsurface Layers

NASA Astrophysics Data System (ADS)

Ayral, D.; Otero-Diaz, M.; Demond, A. H.

2014-12-01

Waste organic contaminants stored in low permeability subsurface layers serve as long-term sources for dissolved phase contaminant plumes. These layers may have a different mineralogical make up than the surrounding geologic media; specifically, they may be characterized by a high clay content. Although these layers are often considered inert, interactions may occur between the clay minerals and the waste liquids that may influence transport. Measurements of the basal spacing of Na-montmorillonite in contact with pure chlorinated organic liquids such as trichloroethylene (TCE) showed that it is similar to that with water; however, its basal spacing in contact with waste chlorinated liquids was reduced, leading to cracking. In fact, the basal spacing in contact with the waste chlorinated liquids was closer to that in contact with air than in contact with water. The observation that contact with pure organic liquids did not cause cracking, but contact with chlorinated wastes obtained from the field did, suggests that other components of the waste are critical to the basal spacing reduction process. Screening experiments indicated that the presence of a binary mixture of surfactants, a nonionic and an anionic surfactant, in the chlorinated solvent were necessary to cause the cracking at the same rate and magnitude as the chlorinated wastes obtained from the field. Fourier transform infrared (FT-IR) spectroscopy measurements suggest that the mixture alters the adsorbed water OH-bending band, implying a displacement of adsorbed water. Coupling these results with sorption and x-ray diffraction (XRD) measurements, a hypothesis of component conformation in the clay interlayer space that leads to cracking can be constructed.

COMBINATION OF A SOURCE REMOVAL REMEDY AND BIOREMEDIATION FOR THE TREATMENT OF A TCE CONTAMINATED AQUIFER

EPA Science Inventory

Historical disposal practices of chlorinated solvents have resulted in the widespread contamination of ground-water resources. These ground-water contaminants exist in the subsurface as free products, residual and vapor phases, and in solution. The remediation of these contamin...

Diagnosing Abiotic Degradation

EPA Science Inventory

The abiotic degradation of chlorinated solvents in ground water can be difficult to diagnose. Under current practice, most of the “evidence” is negative; specifically the apparent disappearance of chlorinated solvents with an accumulation of vinyl chloride, ethane, ethylene, or ...

U. S. EPA’S APPROACH FOR CHLORINATED SOLVENTS

EPA Science Inventory

The approach for chlorinated solvents is similar to the approach for petroleum hydrocarbons. However, there are more mechanisms of removal, including reductive dechlorination (biotic or abiotic), dehydrochloroelimination (abiotic), and hydrolysis (biotic or abiotic). As a resul...

76 FR 13615 - Notice of Proposed Administrative Settlement Pursuant to the Comprehensive Environmental Response...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

... Chlorinated Solvents Superfund Site, Grants, Cibola County, New Mexico. The settlement requires the Holiday..., Texas 75202-2733 or by calling (214) 665-7111. Comments should reference the Grants Chlorinated Solvents...

Sub-slab vs. Near-slab Soil Vapor Profiles at a Chlorinated Solvent Site (1)

EPA Science Inventory

A critical issue in assessing the vapor intrusion pathway is the distribution and migration of VOCs from the subsurface source to the near surface environment. Of particular importance is the influence of a slab. Therefore, EPA/ORD is funding a research program with the primary...

Sub-slab vs. Near-slab Soil Vapor Profiles at a Chlorinated Solvent Site

EPA Science Inventory

A critical issue in assessing the vapor intrusion pathway is the distribution and migration of VOCs from the subsurface source to the near surface environment. Therefore, EPA/ORD funded a research project with the primary goal of comparing vertical profiles of soil gas concentrat...

MICROEMULSION OF MIXED CHLORINATED SOLVENTS USING FOOD GRADE (EDIBLE) SURFACTANTS

EPA Science Inventory

Ground water contamination frequently consists of mixed chlorinated solvents [e.g., tetrachloroethylene (PCE), trichloroethylene (TCE), and trans-1,2- dichloroethylene (DCE)]. In this research, mixtures of the food grade (edible) surfactants bis(2-ethylhexyl) sodium sulfosuccinat...

Use of Field-Scale Phytotechnology for Chlorinated Solvents, Metals, Explosives and Propellants, and Pesticides

EPA Pesticide Factsheets

For this document, the US EPA collected information about 79 field-scale phytotechnology projects conducted throughout the US and Canada that involved treatment of soil and groundwater contaminated with chlorinated solvents, metals, explosives and...

EVALUATION OF ALTERNATIVES TO CHLORINATED SOLVENTS FOR METAL CLEANING

EPA Science Inventory

This project report details results of investigations into alternatives to chlorinated solvents used for metal degreasing. Three companies participated in this project. The results reported for one company document a situation where the conversion to an aqueous cleaning system ha...

BIOVENTING OF CHLORINATED SOLVENTS FOR GROUND-WATER CLEANUP THROUGH BIOREMEDIATION

EPA Science Inventory

Chlorinated solvents such as tetrachloroethylene, trichloroethylene, carbon tetrachloride, chloroform, 1,2-dichloroethane, and dichloromethane (methylene chloride) can exist in contaminated subsurface material as (1) the neat oil, (2) a component of a mixed oily waste, (3) a solu...

Emerging Trends in Regulatory Implementation of MNA

EPA Science Inventory

There are two EPA documents relevant to MNA of Chlorinated Solvents: the Technical Protocol for Evaluating Natural Attenuation of Chlorinated Solvents in Ground Water. EPA/600/R-98/128 September, 1998, and Use of Monitored Natural Attenuation at Superfund, RCRA Corrective Action...

DESIGN AND TESTING OF SECOND GENERATION BIOREMEDIATION TECHNOLOGIES FOR CHLORINATED SOLVENT CONTAMINATED SITES

EPA Science Inventory

The contamination of ground water at industrial and military facilities by chlorinated solvents remains a significant environmental challenge. In the 1990's several successful demonstrations of in situ biodegradation processes, targeted for chloroethenes, occurred. While these tr...

Dendrochemistry of multiple releases of chlorinated solvents at a former industrial site

USGS Publications Warehouse

Balouet, Jean Christophe; Burken, Joel G.; Karg, Frank; Vroblesky, Don; Smith, Kevin T.; Grudd, Hakan; Rindby, Anders; Beaujard, Francois; Chalot, Michel

2012-01-01

Trees can take up and assimilate contaminants from the soil, subsurface, and groundwater. Contaminants in the transpiration stream can become bound or incorporated into the annual rings formed in trees of the temperate zones. The chemical analysis of precisely dated tree rings, called dendrochemistry, can be used to interpret past plant interactions with contaminants. This investigation demonstrates that dendrochemistry can be used to generate historical scenarios of past contamination of groundwater by chlorinated solvents at a site in Verl, Germany. Increment cores from trees at the Verl site were collected and analyzed by energy-dispersive X-ray fluorescence (EDXRF) line scanning. The EDXRF profiles showed four to six time periods where tree rings had anomalously high concentrations of chlorine (Cl) as an indicator of potential contamination by chlorinated solvents.

Analyzing Environmental Policies for Chlorinated Solvents with a Model of Markets and Regulations

DTIC Science & Technology

1991-01-01

electronics, aerospace, fabricated metal products, and dry cleaning depend heavily on chlorinated solvents in their production processes . For example...production processes . The second of the model’s components is a group of economic equations that represents all of the solvent substitutions in...Instead, the process for numerically specifying the substitution parameters involves eliciting expert judgments and then normalizing the parameters

Accounting for Mass Transfer Kinetics when Modeling the Impact of Low Permeability Layers in a Groundwater Source Zone on Dissolved Contaminant Fate and Transport

DTIC Science & Technology

2014-03-27

Clay Interface) ...................................................................................................... 40 Figure 9: Time-Dependent...vs Constant Dissolution Rate BTCs (Monitoring Well in Clay ...pits, poured down sanitary sewer systems, and partially burned in fire training pits. Poor handling and disposal of chlorinated solvents have

PHYTOREMEDIATION POTENTIAL OF A CHLORINATED SOLVENTS PLUME IN CENTRAL FLORIDA

EPA Science Inventory

The potential for phytoremediation of a shallow chlorinated solvent plume was assessed by application of ground water flow and evapotranspiration (ET) models for a site in Orlando, Florida. The focus of the work was on the hydrologic and hydraulic factors that influence phytoreme...

RELATIONSHIP BETWEEN DEHALOCOCCOIDES DNA IN GROUND WATER AND NATURAL ATTENUATION OF CHLORINATED SOLVENTS

EPA Science Inventory

Biological reductive dechlorination is the primary mechanism for natural attenuation of chlorinated solvents in ground water. The only organisms that are known to completely dechlorinate cis-DCE past vinyl chloride to ethylene or ethane are members of the Dehalococcoides group. ...

Review of Abiotic Degradation of Chlorinated Solvents by Reactive Iron Minerals

EPA Science Inventory

Abiotic degradation of chlorinated solvents by reactive iron minerals such as iron sulfides, magnetite, green rust, and other Fe(II)-containing minerals has been observed in both laboratory and field conditions. These reactive iron minerals typically form under iron and sulfate ...

Analytical model for the design of in situ horizontal permeable reactive barriers (HPRBs) for the mitigation of chlorinated solvent vapors in the unsaturated zone

NASA Astrophysics Data System (ADS)

Verginelli, Iason; Capobianco, Oriana; Hartog, Niels; Baciocchi, Renato

2017-02-01

In this work we introduce a 1-D analytical solution that can be used for the design of horizontal permeable reactive barriers (HPRBs) as a vapor mitigation system at sites contaminated by chlorinated solvents. The developed model incorporates a transient diffusion-dominated transport with a second-order reaction rate constant. Furthermore, the model accounts for the HPRB lifetime as a function of the oxidant consumption by reaction with upward vapors and its progressive dissolution and leaching by infiltrating water. Simulation results by this new model closely replicate previous lab-scale tests carried out on trichloroethylene (TCE) using a HPRB containing a mixture of potassium permanganate, water and sand. In view of field applications, design criteria, in terms of the minimum HPRB thickness required to attenuate vapors at acceptable risk-based levels and the expected HPRB lifetime, are determined from site-specific conditions such as vapor source concentration, water infiltration rate and HPRB mixture. The results clearly show the field-scale feasibility of this alternative vapor mitigation system for the treatment of chlorinated solvents. Depending on the oxidation kinetic of the target contaminant, a 1 m thick HPRB can ensure an attenuation of vapor concentrations of orders of magnitude up to 20 years, even for vapor source concentrations up to 10 g/m3. A demonstrative application for representative contaminated site conditions also shows the feasibility of this mitigation system from an economical point of view with capital costs potentially somewhat lower than those of other remediation options, such as soil vapor extraction systems. Overall, based on the experimental and theoretical evaluation thus far, field-scale tests are warranted to verify the potential and cost-effectiveness of HPRBs for vapor mitigation control under various conditions of application.

MICROCOSM STUDY OF DEGRADATION OF CHLORINATED SOLVENTS ON SYNTHETIC GREEN RUST MINERALS

EPA Science Inventory

Green rust minerals contain ferrous ion in their structure that can potentially serve as a chemical reductant for degradation of chlorinated solvents. Green rusts are found in zerovalent iron based permeable reactive barriers and in certain soil and sediments. Some previous labor...

Investigation of In-situ Biogeochemical Reduction of Chlorinated Solvents in Groundwater by Reduced Iron Minerals

EPA Science Inventory

Biogeochemical transformation is a process in which chlorinated solvents are degraded abiotically by reactive minerals formed by, at least in part or indirectly from, anaerobic biological processes. Five mulch biowall and/or vegetable oil-based bioremediation applications for tr...

Monitored natural attenuation of chlorinated solvents—Moving beyond reductive dechlorination

USGS Publications Warehouse

Vangelas, Karen M.; Looney, Brian B.; Early, Tom O.; Gilmore, Tyler; Chapelle, Francis H.; Adams, Karen M.; Sink, Claire H.

2006-01-01

Monitored natural attenuation (MNA), while a remedy of choice for many sites, can be challenging when the contaminants are chlorinated solvents. Even with many high-quality technical guidance references available, there continue to be challenges implementing MNA at some chlorinated solvent sites. The U.S. Department of Energy, as one organization facing such challenges, is leading a project that will incorporate developing concepts and tools into the existing toolbox for selecting and implementing MNA as a remediation option at sites with chlorinated solvent contamination. The structure and goals of this project were introduced in an article in the Winter 2004 issue of Remediation (Sink et al., 2004). This article is a summary of the three technical areas being developed through the project: mass balance, enhanced attenuation, and characterization and monitoring supporting the first two areas.

STRATEGIES FOR THE AEROBIC CO-METABOLISM OF CHLORINATED SOLVENTS. (R825689C019)

EPA Science Inventory

Abstract

Recent field and laboratory studies have evaluated the potential for aerobic co-metabolism of chlorinated solvents. Different co-metabolic substrates and different methods of application have been tried, including growing indigenous microbes in situ, an...

Biological reduction of chlorinated solvents: Batch-scale geochemical modeling

NASA Astrophysics Data System (ADS)

Kouznetsova, Irina; Mao, Xiaomin; Robinson, Clare; Barry, D. A.; Gerhard, Jason I.; McCarty, Perry L.

2010-09-01

Simulation of biodegradation of chlorinated solvents in dense non-aqueous phase liquid (DNAPL) source zones requires a model that accounts for the complexity of processes involved and that is consistent with available laboratory studies. This paper describes such a comprehensive modeling framework that includes microbially mediated degradation processes, microbial population growth and decay, geochemical reactions, as well as interphase mass transfer processes such as DNAPL dissolution, gas formation and mineral precipitation/dissolution. All these processes can be in equilibrium or kinetically controlled. A batch modeling example was presented where the degradation of trichloroethene (TCE) and its byproducts and concomitant reactions (e.g., electron donor fermentation, sulfate reduction, pH buffering by calcite dissolution) were simulated. Local and global sensitivity analysis techniques were applied to delineate the dominant model parameters and processes. Sensitivity analysis indicated that accurate values for parameters related to dichloroethene (DCE) and vinyl chloride (VC) degradation (i.e., DCE and VC maximum utilization rates, yield due to DCE utilization, decay rate for DCE/VC dechlorinators) are important for prediction of the overall dechlorination time. These parameters influence the maximum growth rate of the DCE and VC dechlorinating microorganisms and, thus, the time required for a small initial population to reach a sufficient concentration to significantly affect the overall rate of dechlorination. Self-inhibition of chlorinated ethenes at high concentrations and natural buffering provided by the sediment were also shown to significantly influence the dechlorination time. Furthermore, the analysis indicated that the rates of the competing, nonchlorinated electron-accepting processes relative to the dechlorination kinetics also affect the overall dechlorination time. Results demonstrated that the model developed is a flexible research tool that is able to provide valuable insight into the fundamental processes and their complex interactions during bioremediation of chlorinated ethenes in DNAPL source zones.

Diffusion of Chlorinated Organic Contaminants into Aquitards: Enhanced by the Flocculation of Clay?

NASA Astrophysics Data System (ADS)

Ayral, D.; Otero, M.; Demond, A. H.; Goltz, M. N.; Huang, J.

2011-12-01

Waste organic contaminants stored in low permeability subsurface layers serve as long-term sources for dissolved phase contaminant plumes. Current models consider the movement into and out of aquitards or other low permeability layers to occur through transverse diffusion. Yet, field evidence suggests higher transport rates of contaminants than can be accounted for by diffusion alone. Waste organic liquids contain both organic liquid solvents as well as surface-active solutes. Measurements using montmorillonite in contact with pure chlorinated organic liquids such as trichloroethylene (TCE) showed that the basal spacing is similar to the case of montmorillonite in contact with air, thus suggesting that these fluids have similar flocculation effects. On the other hand, the basal spacing increased in contact with aqueous surfactant solutions. Measurements of the basal spacing in contact with a TCE waste gave the same results as with pure TCE, suggesting that effect on basal spacing is dominated by the organic solvent matrix rather than by the surfactant content. Since flocculation can lead to cracking, this behavior suggests that aquitards underlying aquifers contaminated with chlorinated organic wastes may develop cracks, thus enhancing the transport into low permeability layers.

Diagnostic Tools for Performance Evaluation of Innovative In-Situ Remediation Technologies at Chlorinated Solvent-Contaminated Sites

DTIC Science & Technology

2011-11-01

within a groundwater sample or within a biofilm . FISH probes have been developed that target chlorinated solvent- degrading populations, such as...1988. Bacterial metabolism of protein and endogenous nitrogen compounds. In I.R. Rowland (ed.), Role of the gut flora in toxicity and cancer (p. 227

Independent Design Review: Grants Chlorinated Solvents Plume, Superfund Site, Grants, Cibola County, New Mexico, EPA Region 6

EPA Pesticide Factsheets

The Grants Chlorinated Solvents Plume Superfund Site in Grants, Cibola County, New Mexico was selected by EPA OSRTI based on a nomination from EPA Region 6. The remedy is in the early design stage and has an estimated cost of $29.5 million.

Natural Attenuation of Chlorinated Solvents and Fuel Components (BTEX and MTBE) in Ground Water

EPA Science Inventory

Monitored Natural Attenuation is widely used in the USA to deal with ground water contamination from fuel components such as the BTEX compounds or MTBE or TBA and from chlorinated solvents such as PCE, TCE, and TCA. This presentation reviews the theory and practice of MNA in the...

In situ remediation of chlorinated solvent-contaminated groundwater using ZVI/organic carbon amendment in China: field pilot test and full-scale application.

PubMed

Yang, Jie; Meng, Liang; Guo, Lin

2018-02-01

Chlorinated solvents in groundwater pose threats to human health and the environment due to their carcinogenesis and bioaccumulation. These problems are often more severe in developing countries such as China. Thus, methods for chlorinated solvent-contaminated groundwater remediation are urgently needed. This study presents a technique of in situ remediation via the direct-push amendment injection that enhances the reductive dechlorination of chlorinated solvents in groundwater in the low-permeability aquifer. A field-based pilot test and a following real-world, full-scale application were conducted at an active manufacturing facility in Shanghai, China. The chlorinated solvents found at the clay till site included 1,1,1-trichloroethane (1,1,1-TCA), 1,1-dichloroethane (1,1-DCA), 1,1-dichloroethylene (1,1-DCE), vinyl chloride (VC), and chloroethane (CA). A commercially available amendment (EHC ® , Peroxychem, Philadelphia, PA) combining zero-valent iron and organic carbon was used to treat the above pollutants. Pilot test results showed that direct-push EHC injection efficiently facilitated the in situ reductive remediation of groundwater contaminated with chlorinated solvents. The mean removal rates of 1,1,1-TCA, 1,1-DCA, and 1,1-DCE at 270 days post-injection were 99.6, 99.3, and 73.3%, respectively, which were obviously higher than those of VC and CA (42.3 and 37.1%, respectively). Clear decreases in oxidation-reduction potential and dissolved oxygen concentration, and increases in Fe 2+ and total organic carbon concentration, were also observed during the monitoring period. These indicate that EHC promotes the anaerobic degradation of chlorinated hydrocarbons primarily via long-term biological reductive dechlorination, with instant chemical reductive dechlorination acting as a secondary pathway. The optimal effective time of EHC injection was 0-90 days, and its radius of influence was 1.5 m. In full-scale application, the maximum concentrations of 1,1,1-TCA and 1,1-DCA in the contaminate plume fell below the relevant Dutch Intervention Values at 180 days post-injection. Moreover, the dynamics of the target pollutant concentrations mirrored those of the pilot test. Thus, we have demonstrated that the direct-push injection of EHC successfully leads to the remediation of chlorinated solvent-contaminated groundwater in a real-world scenario. The parameters determined by this study (e.g., effectiveness, injection amount, injection depth, injection pressures, and radius of influence) are applicable to other low-permeability contaminated sites where in situ remediation by enhanced reductive dechlorination is required.

The study on the extraction and recovery of Au from scrap of the used computer using chloride solvent

NASA Astrophysics Data System (ADS)

Oh, Su-ji; Choi, Eunju; Choi, Nagchoul; Park, Cheonyoung

2013-04-01

Recently, due to the realization of environmental problems of cyanide, it is a worldwide quest to find viable alternatives. One of the alternatives is a chloride solvent(chlorine-hypochlorite acid) with an appropriate oxidizing agent. The rate of dissolution of Au by chloride solvent is much faster than that by cyanide. Also, due to presence of chloride ions, there is no passivation of gold surfaces during chlorination. The objective of this work was to investigate the effect of Au extraction efficiency under various experimental conditions(pulp density, chlorine-hypochlorite ratio and concentration of NaCl) from scrap of the used computer by chloride solvent. In addition, the recovery experiment was conducted to examine of the precipitation efficiency of Au under various metabisulfite concentration from extracted solution. In an EDS analysis, valuable metals such as Cu, Sn, Sb, Al, Ni, Pb and Au were observed in scrap of the used computer. The result of extraction experiment showed that the highest extraction rate was obtained under 1% of pulp density with a chlorine-hypochlorite ratio of 2:1, and a concentration of NaCl at 2M. The highest Au recovery(precipitation) rate was observed the addition of sodium metabisulfite at 2M concentration. Under these conditions, chlorine-hypochlorite could effectively Au extraction from scrap of the used computer sections and the additive reagent using sodium metabisulfite could easily precipitate the Au from the chlorine-hypochlorite solution.

EVALUATION OF THE PROTOCOL FOR THE NATURAL ATTENUATION OF CHLORINATED SOLVENTS: CASE STUDY AT THE TWIN CITIES ARMY AMMUNITION PLANT

EPA Science Inventory

At the request of staff in the EPA Regions, EPA?s Office of Research and Development carried out an independent evaluation of the Technical Protocol for Evaluating Natural Attenuation of Chlorinated Solvents in Ground Water (EPA/600/R-98/128). The Protocol was developed around c...

In situ thermally enhanced biodegradation of petroleum fuel hydrocarbons and halogenated organic solvents

DOEpatents

Taylor, Robert T.; Jackson, Kenneth J.; Duba, Alfred G.; Chen, Ching-I

1998-01-01

An in situ thermally enhanced microbial remediation strategy and a method for the biodegradation of toxic petroleum fuel hydrocarbon and halogenated organic solvent contaminants. The method utilizes nonpathogenic, thermophilic bacteria for the thermal biodegradation of toxic and carcinogenic contaminants, such as benzene, toluene, ethylbenzene and xylenes, from fuel leaks and the chlorinated ethenes, such as trichloroethylene, chlorinated ethanes, such as 1,1,1-trichloroethane, and chlorinated methanes, such as chloroform, from past solvent cleaning practices. The method relies on and takes advantage of the pre-existing heated conditions and the array of delivery/recovery wells that are created and in place following primary subsurface contaminant volatilization efforts via thermal approaches, such as dynamic underground steam-electrical heating.

In situ thermally enhanced biodegradation of petroleum fuel hydrocarbons and halogenated organic solvents

DOEpatents

Taylor, R.T.; Jackson, K.J.; Duba, A.G.; Chen, C.I.

1998-05-19

An in situ thermally enhanced microbial remediation strategy and a method for the biodegradation of toxic petroleum fuel hydrocarbon and halogenated organic solvent contaminants are described. The method utilizes nonpathogenic, thermophilic bacteria for the thermal biodegradation of toxic and carcinogenic contaminants, such as benzene, toluene, ethylbenzene and xylenes, from fuel leaks and the chlorinated ethenes, such as trichloroethylene, chlorinated ethanes, such as 1,1,1-trichloroethane, and chlorinated methanes, such as chloroform, from past solvent cleaning practices. The method relies on and takes advantage of the pre-existing heated conditions and the array of delivery/recovery wells that are created and in place following primary subsurface contaminant volatilization efforts via thermal approaches, such as dynamic underground steam-electrical heating. 21 figs.

Use of Nanoscale Emulsified Zero-valent Iron to Treat a Chlorinated Solvent Source Zone at Site 45, Marine Corp Recruit Depot, Parris Island, South Carolina

EPA Science Inventory

This document summarizes the research activities currently underway at the Solid Waste Management Unit 45 (Site 45), Marine Corps Recruit Depot, Parris Island, South Carolina. A pilot field test was initiated in 2005 at this site to evaluate the effectiveness of nanoscale emulsif...

Principles and Practices of Enhanced Anaerobic Bioremediation of Chlorinated Solvents

DTIC Science & Technology

2004-09-01

high - fructose corn syrup (HFCS), whey, bark mulch and compost, chitin, and gaseous hydrogen. Table 1.2...Benzoate Injection wells or circulation systems Dissolved in water Continuous to monthly Molasses, High Fructose Corn Syrup Injection wells...to 0.35 High (> 100) Refined Sugars ( high fructose corn syrup ) 0.25 to 0.30 Moderate (> 20) Soluble substrates may be used for source

Combining Low-Energy Electrical Resistance Heating with Biotic and Abiotic Reactions for Treatment of Chlorinated Solvent DNAPL Source Areas

DTIC Science & Technology

2015-01-01

5 2.1.2 In Situ Bioremediation ...Technology Certification Program gpm gallons per minute ISB in situ bioremediation JBLM Joint Base Lewis-McChord mmol millimole MROD Mount...EXECUTIVE SUMMARY BACKGROUND The applicability of in situ groundwater remedies such as in situ bioremediation (ISB) or zero valent iron (ZVI) reduction

Decision & Management Tools for DNAPL Sites: Optimization of Chlorinated Solvent Source and Plume Remediation Considering Uncertainty

DTIC Science & Technology

2010-09-01

differentiated between source codes and input/output files. The text makes references to a REMChlor-GoldSim model. The text also refers to the REMChlor...To the extent possible, the instructions should be accurate and precise. The documentation should differentiate between describing what is actually...Windows XP operating system Model Input Paran1eters. · n1e input parameters were identical to those utilized and reported by CDM (See Table .I .from

IN-SITU AQUIFER RESTORATION OF CHLORINATED ALIPHATICS BY METHANOTROPHIC BACTERIA

EPA Science Inventory

This project evaluated the potential of enhanced in-situ biotransformation of chlorinated aliphatic solvents by a bacterial community grown on methane under aerobic conditions. The target chlorinated compounds were trichloroethene (TCE), cis-and trans-1,2-dichloroethene (DCE), an...

Project Summary. IN-SITU AQUIFER RESTORATION OF CHLORINATED ALIPHATICS BY METHANOTROPHIC BACTERIA

EPA Science Inventory

This project evaluated the potential of an innovative approach to aquifer restoration: enhanced in-situ biotransformation of chlorinated aliphatic solvents by a bacterial community grown on methane under aerobic conditions. The target chlorinated compounds were trichloroethene (...

Enhanced Attenuation of Unsaturated Chlorinated Solvent Source Zones using Direct Hydrogen Delivery

DTIC Science & Technology

2013-01-01

map, York , Nebraska. ...................................... 15 Figure 3. SVE system map...projected to be $49/cy. This would compare to the following costs per cubic yards: $37 for a new -build SVE system; $20 to keep an existing SVE...Atlas Missile Site 10 in Former Lincoln Air Force Base (AFB) was selected for the demonstration located in York , Nebraska (Figure 2). Figure 2

Combining Low-Energy Electrical Resistance Heating with Biotic and Abiotic Reactions for Treatment of Chlorinated Solvent DNAPL Source Area

DTIC Science & Technology

2012-12-01

DEPTH DRILLED INTO ROCK NIA 18. TOTAL CORE RECOVERY FOR BORING 9. TOTAL DEPTH OF HOLE 3o.o I 19. SIGNATURE OF INSPECT/’fi1’ ~V.U.. ELEVATION...EPA/540/-93/ 505 , U.S. Environmental Protection Agency Risk Reduction Engineering Laboratory, Cincinnati, OH. Farrell, J., Kason, M., Melitas, N., Li

Field-Scale Evaluation of Monitored Natural Attenuation for Dissolved Chlorinated Solvent Plumes

DTIC Science & Technology

2009-04-01

biological in-situ treatment, an air sparging pilot study, and a phytoremediation study. The innovative technology studies were conducted within the source... phytoremediation (June to September 1997), reductive anaerobic biological in-situ treatment technology (RABITT; 1998), and groundwater recirculation wells...u g / L ) Measured Concentrations in 1381MWS09 Air Sparge Pilot Test (1996/1997) Phytoremediation Pilot Test (1997) RABITT Pilot Test (1998

Analytical model for the design of in situ horizontal permeable reactive barriers (HPRBs) for the mitigation of chlorinated solvent vapors in the unsaturated zone.

PubMed

Verginelli, Iason; Capobianco, Oriana; Hartog, Niels; Baciocchi, Renato

2017-02-01

In this work we introduce a 1-D analytical solution that can be used for the design of horizontal permeable reactive barriers (HPRBs) as a vapor mitigation system at sites contaminated by chlorinated solvents. The developed model incorporates a transient diffusion-dominated transport with a second-order reaction rate constant. Furthermore, the model accounts for the HPRB lifetime as a function of the oxidant consumption by reaction with upward vapors and its progressive dissolution and leaching by infiltrating water. Simulation results by this new model closely replicate previous lab-scale tests carried out on trichloroethylene (TCE) using a HPRB containing a mixture of potassium permanganate, water and sand. In view of field applications, design criteria, in terms of the minimum HPRB thickness required to attenuate vapors at acceptable risk-based levels and the expected HPRB lifetime, are determined from site-specific conditions such as vapor source concentration, water infiltration rate and HPRB mixture. The results clearly show the field-scale feasibility of this alternative vapor mitigation system for the treatment of chlorinated solvents. Depending on the oxidation kinetic of the target contaminant, a 1m thick HPRB can ensure an attenuation of vapor concentrations of orders of magnitude up to 20years, even for vapor source concentrations up to 10g/m 3 . A demonstrative application for representative contaminated site conditions also shows the feasibility of this mitigation system from an economical point of view with capital costs potentially somewhat lower than those of other remediation options, such as soil vapor extraction systems. Overall, based on the experimental and theoretical evaluation thus far, field-scale tests are warranted to verify the potential and cost-effectiveness of HPRBs for vapor mitigation control under various conditions of application. Copyright © 2017 Elsevier B.V. All rights reserved.

Coal desulfurization process

NASA Technical Reports Server (NTRS)

Hsu, G. C.; Gavalas, G. R.; Ganguli, P. S.; Kalfayan, S. H.

1978-01-01

A method for chlorinolysis of coal is an organic solvent at a moderate temperautre and atmospheric pressure has been proven to be effective in removing sulfur, particularly the organic sulfur, from coal. Chlorine gas is bubbled through a slurry of moist coal in chlorinated solvent. The chlorinated coal is separated, hydrolyzed and the dechlorinated. Preliminary results of treating a high sulfutr (4.77%S) bituminous coal show that up to 70% organic sulfur, 90% hyritic sulfur and 76% total sulfur can be removed. The treated coal is dechlorinated by heating at 500 C. The presence of moisture helps to remove organic sulfur.

Development of Permeable Reactive Barriers (PRB) Using Edible Oils

DTIC Science & Technology

2008-06-01

developed for the in-situ treatment of hazardous constituents including chlorinated solvents, perchlorate (ClO4-), chromate (CrO4-2) and oxidized... beef tallow, melted corn oil margarine, coconut oil and molasses supported the complete reductive dehalogenation of PCE to ethene in microcosms using...anaerobic bioremediation processes are being developed for the in-situ treatment of hazardous constituents including chlorinated solvents, perchlorate

The Market Responses to the Government Regulation of Chlorinated Solvents: A Policy Analysis

DTIC Science & Technology

1988-10-01

in the process of statistical estimation of model parameters. The results of the estimation process applied to chlorinated solvent markets show the...93 C.5. Marginal Feedstock Cost Series Estimates for Process Share of Total Production .................................. 94 F.I...poliay context for this research. Section III provides analysis necessary to understand the chemicals involved, their production processes and costs, and

Workshop on In Situ Biogeochemical Transformation of Chlorinated Solvents

DTIC Science & Technology

2008-02-01

sites across the country, and also has its own internal research programs. In situ bioremediation has become a widely- used technology for...concern [e.g., dithionite, sulfate (at high concentrations), pesticides , and agri-chemicals that are residues in mulch used in biowalls, as well as... Bioremediation of Chlorinated Solvents in Groundwater Using a Permeable Mulch Biowall, Operable Unit 1, Altus Air Force Base, Oklahoma. Prepared

pH Control for Effective Anaerobic Bioremediation of Chlorinated Solvents

NASA Astrophysics Data System (ADS)

Robinson, C.; Barry, D.; Gerhard, J. I.; Kouznetsova, I.

2007-12-01

SABRE (Source Area BioREmediation) is a 4-year collaborative project that aims to evaluate the performance of enhanced anaerobic bioremediation for the treatment of chlorinated solvent DNAPL source areas. The project focuses on a pilot scale demonstration at a trichloroethene (TCE) DNAPL field site, and includes complementary laboratory and modelling studies. Organic acids and hydrogen ions (HCl) typically build up in the treatment zone during anaerobic bioremediation. In aquifer systems with relatively low buffering capacity the generation of these products can cause significant groundwater acidification thereby inhibiting dehalogenating activity. Where the soil buffering capacity is exceeded, addition of buffer may be needed for the effective continuation of TCE degradation. As an aid to the design of remediation schemes, a geochemical model was designed to predict the amount of buffer required to maintain the source zone pH at a suitable level for dechlorinating bacteria (i.e. > 6.5). The model accounts for the amount of TCE to be degraded, site water chemistry, type of organic amendment and soil mineralogy. It assumes complete dechlorination of TCE, and further considers mineral dissolution and precipitation kinetics. The model is applicable to a wide range of sites. For illustration we present results pertinent to the SABRE field site. Model results indicate that, for the extensive dechlorination expected in proximity to the SABRE DNAPL source zone, significant buffer addition may be necessary. Additional simulations are performed to identify buffer requirements over a wider range of field conditions.

The legacy of chlorinated solvents in the Birmingham aquifer, UK: Observations spanning three decades and the challenge of future urban groundwater development

NASA Astrophysics Data System (ADS)

Rivett, Michael O.; Turner, Ryan J.; Glibbery (née Murcott), Penny; Cuthbert, Mark O.

2012-10-01

Licensed abstraction well data collected during 1986-2008 from a total of 77 wells mainly located at industrial sites combined with historic land use data from 1975 has allowed insight into the legacy of chlorinated solvent contamination in the Birmingham aquifer that underlies the UK's second largest city. This legacy, expected to be reasonably symptomatic of those occurring in other urban aquifers, was characterised by: dominance of parent solvents, particularly TCE (trichloroethene) that widely exceeded drinking-water quality criteria; greater TCE occurrence in wells in proximity to increased historic land use by the metal/engineering solvent-user industry (the relationship providing a first-pass indicator of future resource development potential); regional groundwater vulnerability controls; well abstraction changes (over months to decades) influential of observed concentration transients and anticipated plume capture or release; persistence of contamination over decades (with less soluble PCE (perchloroethene) showing increased persistence relative to TCE) that was reasonably ascribed to slow contaminant release from DNAPL (dense non-aqueous phase liquid) sources and, or low permeability layers; presence of dechlorination products arising from solvent (bio)degradation, although this key attenuation process appeared to have moderate to weak influence regionally on plumes; and, inadvertent, but significant solvent mass removal from the aquifer by industrial abstractions. Key challenges to realising future urban groundwater development were identified based on the observed legacy and well capture zone simulations. Despite the extensive contamination of the aquifer, it should still be possible to develop wells of high (several megalitres per day) capacity for drinking water supply (or other lower grade uses) without the requirement for solvent treatment. In those areas with higher risk of contamination, our dataset, together with application of emergent risk assessment approaches (that our dataset may serve to validate), could be used to inform potential abstractors as to whether solvent treatment is likely to be required at a particular abstraction site with time. Challenges identified that were relevant to the future development of Birmingham and urban aquifers more generally include the adequacy of groundwater quality monitoring data and uncertainties in contaminant source terms, abstraction well capture zone predictions and plume natural attenuation, in particular degradation rates. The study endorses that despite significant solvent contamination encountered, strategies can, and need, to be increasingly found to reclaim urban aquifer resources and more sustainably meet urban water demands.

Hazardous Waste Cleanup: Solvents & Petroleum Incorporated in Syracuse, New York

EPA Pesticide Factsheets

The Solvents and Petroleum Service, Inc. (SPS) facility is located at 1405 Brewerton Road in Syracuse, New York. The current owner is a distributor of organic and chlorinated solvents to industries in the Central New York region. Solvents are stored in

Natural Attenuation in Streambed Sediment Receiving Chlorinated Solvents from Underlying Fracture Networks

DOE PAGES

Şimşir, Burcu; Yan, Jun; Im, Jeongdae; ...

2017-03-22

Contaminant discharge from fractured bedrock formations remains a remediation challenge. Here, we applied an integrated approach to assess the natural attenuation potential of sediment that forms the transition zone between upwelling groundwater from a chlorinated solvent-contaminated fractured bedrock aquifer and the receiving surface water. In situ measurements demonstrated that reductive dechlorination in the sediment attenuated chlorinated compounds before reaching the water column. Microcosms established with creek sediment or in situ incubated Bio-Sep beads degraded C 1-C 3 chlorinated solvents to less-chlorinated or innocuous products. Quantitative PCR and 16S rRNA gene amplicon sequencing revealed the abundance and spatial distribution of knownmore » dechlorinator biomarker genes within the creek sediment and demonstrated that multiple dechlorinator populations degrading chlorinatedC 1-C 3 alkanes and alkenes co-inhabit the sediment. Phylogenetic classification of bacterial and archaeal sequences indicated a relatively uniform distribution over spatial (300 m horizontally) scale, but Dehalococcoides and Dehalobacter were more abundant in deeper sediment, where 5.7 ± 0.4 × 10 5 and 5.4 ± 0.9 × 10 6 16S rRNA gene copies per g of sediment, respectively, were measured. The microbiological and hydrogeological characterization demonstrated that microbial processes at the fractured bedrock-sediment interface were crucial for preventing contaminants reaching the water column, emphasizing the relevance of this critical zone environment for contaminant attenuation.« less

Natural Attenuation in Streambed Sediment Receiving Chlorinated Solvents from Underlying Fracture Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Şimşir, Burcu; Yan, Jun; Im, Jeongdae

Contaminant discharge from fractured bedrock formations remains a remediation challenge. Here, we applied an integrated approach to assess the natural attenuation potential of sediment that forms the transition zone between upwelling groundwater from a chlorinated solvent-contaminated fractured bedrock aquifer and the receiving surface water. In situ measurements demonstrated that reductive dechlorination in the sediment attenuated chlorinated compounds before reaching the water column. Microcosms established with creek sediment or in situ incubated Bio-Sep beads degraded C 1-C 3 chlorinated solvents to less-chlorinated or innocuous products. Quantitative PCR and 16S rRNA gene amplicon sequencing revealed the abundance and spatial distribution of knownmore » dechlorinator biomarker genes within the creek sediment and demonstrated that multiple dechlorinator populations degrading chlorinatedC 1-C 3 alkanes and alkenes co-inhabit the sediment. Phylogenetic classification of bacterial and archaeal sequences indicated a relatively uniform distribution over spatial (300 m horizontally) scale, but Dehalococcoides and Dehalobacter were more abundant in deeper sediment, where 5.7 ± 0.4 × 10 5 and 5.4 ± 0.9 × 10 6 16S rRNA gene copies per g of sediment, respectively, were measured. The microbiological and hydrogeological characterization demonstrated that microbial processes at the fractured bedrock-sediment interface were crucial for preventing contaminants reaching the water column, emphasizing the relevance of this critical zone environment for contaminant attenuation.« less

Integrated Stable Isotope - Reactive Transport Model Approach for Assessment of Chlorinated Solvent Degradation

DTIC Science & Technology

2016-05-01

Certification Program ETH Ethene GC Gas Chromatography GC-IRMS Gas Chromatography Isotope Ratio Mass Spectroscopy H Hydrogen IRMS Isotope...tool for attenuation of chlorinated solvents. The Demonstration Site was Operable Unit 10 at Hill AFB, Utah , a site where groundwater is impacted...techniques. The method involves extraction of the target compounds from environmental sample matrix, followed by separation of the compounds using gas

Monitoring trihalomethanes in chlorinated waters using a dispersive liquid-liquid microextraction method with a non-chlorinated organic solvent and gas chromatography-mass spectrometry.

PubMed

Pacheco-Fernández, Idaira; Herrera-Fuentes, Ariadna; Delgado, Bárbara; Pino, Verónica; Ayala, Juan H; Afonso, Ana M

2017-03-01

The environmental monitoring of trihalomethanes (THMs) has been performed by setting up a dispersive liquid-liquid microextraction method in combination with gas chromatography (GC)-mass spectrometry (MS). The optimized method only requires ∼26 µL of decanol as extractant solvent, dissolved in ∼1 mL of acetone (dispersive solvent) for 5 mL of the environmental water containing THMs. The mixture is then subjected to vortex for 1 min and then centrifuged for 2 min at 3500 rpm. The microdroplet containing the extracted THMs is then sampled with a micro-syringe, and injected (1 µL) in the GC-MS. The method is characterized for being fast (3 min for the entire sample preparation step) and environmentally friendly (low amounts of solvents required, being all non-chlorinated), and also for getting average relative recoveries of 90.2-106% in tap waters; relative standard deviation values always lower than 11%; average enrichment factors of 48-49; and detection limits down to 0.7 µg·L-1. Several waters: tap waters, pool waters, and wastewaters were successfully analyzed with the method proposed. Furthermore, the method was used to monitor the formation of THMs in wastewaters when different chlorination parameters, namely temperature and pH, were varied.

Novel carotenol chlorin esters in marine sediments and water column particulate matter

NASA Astrophysics Data System (ADS)

Goericke, Ralf; Shankle, Amy; Repeta, Daniel J.

1999-09-01

Novel esters of carotenols and chlorins (carotenol chlorin esters, CCEs) were found in recent sediments from the California Borderlands, Monterey Bay, and the Peru and Oman margins. The chlorins associated with CCEs were pheophorbide a and pyropheophorbide a, degradation products of chlorophyll a. Isofucoxanthin-dehydrate and isofucoxanthinol-dehydrate and possibly their isomers, degradation products of fucoxanthin, were the only carotenols associated with CCEs. This result is surprising, considering that at least 8 major degradation products of fucoxanthin are present in organic-rich marine sediments. The carotenols of CCEs are likely derived from diatoms as these are the primary source for fucoxanthin in the marine environment. In sediments studied by us, CCEs contributed approximately 10% to total solvent extractable chlorins. The high relative concentrations of CCEs in these sediments suggest that CCEs are an important degradation product of chlorophyll a in some marine environments; a pathway hitherto unrecognized. Off Oman and Southern California we found CCEs in water column suspended particulate matter when diatoms dominated the phytoplankton community. By analogy with sterol chlorin esters, we suggest that CCEs are primarily produced by enzymatically mediated transesterifications in crustaceans grazing on diatoms. We are currently studying if CCEs are biomarkers for the grazing of crustaceans on diatoms, an important pathway of carbon remineralization in the marine environment.

Enhanced Amendment Delivery to Low Permeability Zones for Chlorinated Solvent Source Area Bioremediation

DTIC Science & Technology

2014-10-01

enhanced amendments delivery process, a non-toxic biodegradable polymer, such as xanthan gum, is added to the injection solution to form a non- Newtonian...Once injection stops, the injected fluid viscosity increases and creates a more stable zone for biodegradation reactions because the amendment-laden...electron acceptors and biodegradation of the shear-thinning agent. • Determine the cost factors for applying the STF enhanced delivery technology

Enhanced Amendment Delivery to Low Permeability Zones for Chlorinated Solvent Source Area Bioremediation

DTIC Science & Technology

2014-09-01

suspend manganese dioxide particles produced from oxidation of permanganate in aqueous phase (Crimi and Ko, 2009). Xanthan gum is a biopolymer that...shear-thinning fluids for improving treatment of low-k zones. This study established that combinations of xanthan gum and potassium permanganate ...flow cell experiments using xanthan gum solution to deliver permanganate , Chokejaroenrat et al. (2013, 2014) presented a set of data supporting that

The DNAPL Remediation Challenge: Is There a Case for Source Depletion?

DTIC Science & Technology

2003-12-01

fermentation products acting as electron donors to promote reductive dechlorination of chlorinated solvents (e.g., see discussion on Sages and Bachman...has been primarily used to remove organic contamination in the vadose zone (see e.g., Stegemeier and Vinegar , 2001). Signifi cant removals of...Stegemeier, G.L., and H.J. Vinegar . 2001. Thermal conduction heating for in-situ thermal desorption of soils. In: Hazardous and Radioactive Waste Treatment

21 CFR 177.1650 - Polysulfide polymer-polyepoxy resins.

Code of Federal Regulations, 2011 CFR

2011-04-01

...(2-chloroethyl) formal Bis(dichloropropyl) formal Cross-linking agent. Butyl alcohol Solvent. Carbon black (channel process) Chlorinated paraffins Cross-linking agent. Epoxidized linseed oil Epoxidized... monobutyl ether Solvent. Magnesium chloride Methyl isobutyl ketone Solvent. Naphthalene sulfonic acid...

Bioremediation of a Large Chlorinated Solvent Plume, Dover AFB, DE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bloom, Aleisa C

2015-01-01

Bioremediation of a Large Chlorinated Solvent Plume, Dover AFB, DE Aleisa Bloom, (Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA) Robert Lyon (bob.lyon@aecom.com), Laurie Stenberg, and Holly Brown (AECOM, Germantown, Maryland, USA) ABSTRACT: Past disposal practices at Dover Air Force Base (AFB), Delaware, created a large solvent plume called Area 6 (about 1 mile long, 2,000 feet wide, and 345 acres). The main contaminants are PCE, TCE, and their degradation products. The remedy is in-situ accelerated anaerobic bioremediation (AAB). AAB started in 2006 and is focusing on source areas and downgradient plume cores. Direct-push injections occurred in source areas wheremore » contamination is typically between 5 and 20 feet below ground surface. Lower concentration dissolved-phased contamination is present downgradient at 35 and 50 feet below ground surface. Here, permanent injection/extraction wells installed in transects perpendicular to the flow of groundwater are used to apply AAB. The AAB substrate is a mix of sodium lactate, emulsified vegetable oil, and nutrients. After eight years, dissolved contaminant mass within the main 80-acre treatment area has been reduced by over 98 percent. This successful application of AAB has stopped the flux of contaminants to the more distal portions of the plume. While more time is needed for effects to be seen in the distal plume, AAB injections will soon cease, and the remedy will transition to natural attenuation. INTRODUCTION Oak Ridge National Laboratory Environmental Science Division (ORNL) and AECOM (formerly URS Corporation) have successfully implemented in situ accelerated anaerobic bioremediation (AAB) to remediate chlorinated solvent contamination in a large, multi-sourced groundwater plume at Dover Air Force Base (AFB). AAB has resulted in significant reductions of dissolved phase chlorinated solvent concentrations. This plume, called Area 6, was originally over 1 mile in length and over 2,000 feet wide (Figure 1). It originated from at least four separate source areas that comingled in the subsurface to form the large plume. The major contaminants of concern (COCs) are tetrachloroethene (PCE), trichloroethene (TCE), and 1,1,1-trichloroethane (1,1,1-TCA), which were historically used for degreasing operations in the maintenance of aircraft and support vehicles. Relatively small areas of elevated PCE, TCE, and 1,1,1-TCA were delineated in the shallow portion of the water table aquifer by direct-push groundwater sampling. Focused direct-push AAB treatment occurred in March 2006 at these source areas (Figure 1). Downgradient of the these areas and deeper in the aquifer, AAB treatment was implemented using rows of extraction/injection wells oriented perpendicular to groundwater flow to create multiple reductive zones across the plume cores, defined as areas where more than 1,000 micrograms per liter (ug/L) total solvent concentrations were present. Initial indications of successful degradation were observed within 6 months of starting injections. FIGURE 1. Dover AFB Area 6 plume. This paper describes the AAB implementation and progress of remediation after 8 years of treatment and periodic groundwater monitoring. SITE LITHOLOGY Contamination at the site is limited to the surficial aquifer, which consists of 35 to 50 feet (ft) (11 to 15 meters [m]) of unconsolidated Pleistocene deposits of the Columbia Formation. The Columbia Formation consists of fine to coarse sand with silt and clay lenses and less common gravel lenses. Silts and silty sands are generally encountered to a depth of 10 to 12 ft (3.05 to 3.65 m) below ground surface (bgs) and grade to medium- and coarse-grained sands to a depth of 35 to 50 ft (11 to 15 m) bgs. There is a clay and silt unit (part of the Calvert Formation) below the surficial aquifer that acts as an aquitard to the downward migration of contaminants. The depth to the water table varies across the site but usually ranges from 8 to 15 ft (2.4 to 4.5 m) bgs in the treatment area. REMEDIAL APPROACH AND OPERATIONS Because the Columbia Aquifer is used as a source of potable water off base, the remedial goal is to restore the aquifer to usable condition, i.e., reduce all chemicals of concern to below drinking water maximum contaminant levels (MCLs). To achieve this goal, AAB was selected as the best remedial alternative to reduce the solvent contamination. Source areas with high solvent concentrations were present in the shallow portion of the aquifer. From the source areas, dissolved solvents migrated downgradient and deeper in the aquifer with the flow of groundwater. In the deeper portion of the aquifer, the individual plumes comingle to form the larger Area 6 Plume, which covers approximately 345 acres. Types of Substrate. Previous AAB pilot tests at Dover AFB used either sodium lactate or emulsified vegetable oil (EVO) as substrates to stimulate microbial growth. The best results were obtained with...« less

Subsurface occurrence and potential source areas of chlorinated ethenes identified using concentrations and concentration ratios, Air Force Plant 4 and Naval Air Station-Joint Reserve Base Carswell Field, Fort Worth, Texas

USGS Publications Warehouse

Garcia, C. Amanda

2005-01-01

The U.S. Geological Survey, in cooperation with the U.S. Air Force Aeronautical Systems Center, Environmental Management Directorate, conducted a study during 2003-05 to characterize the subsurface occurrence and identify potential source areas of the volatile organic compounds classified as chlorinated ethenes at U.S. Air Force Plant 4 (AFP4) and adjacent Naval Air Station-Joint Reserve Base Carswell Field (NAS-JRB) at Fort Worth, Texas. The solubilized chlorinated ethenes detected in the alluvial aquifer originated as either released solvents (tetrachloroethene [PCE], trichloroethene [TCE], and trans-1,2-dichloroethene [trans-DCE]) or degradation products of the released solvents (TCE, cis-1,2-dichloroethene [cis-DCE], and trans-DCE). The combined influences of topographic- and bedrock-surface configurations result in a water table that generally slopes away from a ground-water divide approximately coincident with bedrock highs and the 1-mile-long aircraft assembly building at AFP4. Highest TCE concentrations (10,000 to 920,000 micrograms per liter) occur near Building 181, west of Building 12, and at landfill 3. Highest PCE concentrations (500 to 920 micrograms per liter) occur near Buildings 4 and 5. Highest cis-DCE concentrations (5,000 to 710,000 micrograms per liter) occur at landfill 3. Highest trans-DCE concentrations (1,000 to 1,700 micrograms per liter) occur just south of Building 181 and at landfill 3. Ratios of parent-compound to daughter-product concentrations that increase in relatively short distances (tens to 100s of feet) along downgradient ground-water flow paths can indicate a contributing source in the vicinity of the increase. Largest increases in ratio of PCE to TCE concentrations are three orders of magnitude from 0.01 to 2.7 and 7.1 between nearby wells in the northeastern part of NAS-JRB. In the northern part of NAS-JRB, the largest increases in TCE to total DCE concentration ratios relative to ratios at upgradient wells are from 17 to 240 or from 17 to 260. In the southern part of NAS-JRB, the largest ratio increases with respect to those at upgradient wells are from 22 and 24 to 130, and from 0 and 7.2 to 71. Numerous maximum historical ratios of trans-DCE to cis-DCE are greater than 1, which can indicate that trans-DCE likely was released as a solvent and does not occur only as a result of degradation of TCE. High concentrations of TCE, PCE, cis-DCE, and trans-DCE, abrupt increases in ratios of PCE to TCE and TCE to total DCE, and ratios of trans-DCE to cis-DCE greater than 1 were used to identify 16 potential source areas of chlorinated ethenes at NAS-JRB. The evidence for some of the potential source areas is stronger than for others, but each area reflects one or more of the conditions indicative of chlorinated ethenes entering the aquifer. Potential source areas supported by the strongest evidence are Building 181, between buildings 4 and 5, just west of Building 12, and landfills 1 and 3. The highest historical TCE concentration in the study area, 920,000 micrograms per liter, is near Building 181. The potential source area between Buildings 4 and 5 primarily is identified by notably high PCE concentrations (to 920 micrograms per liter). Primary evidence for the potential source are just west of Building 12 is the notably high TCE concentrations (for example, 160,000 micrograms per liter) that appear to originate in the area. Primary evidence for the potential source area at landfills 1 and (primarily) 3 is the magnitudes of TCE concentrations (for example, two in the 100,000-to-920,000-microgram-per-liter range), cis-DCE concentrations (several in the 5,000-to-710,000-microgram-per-liter range), and trans-DCE concentrations (several in the 500-to-1,700-microgram-per-liter range). The ratio of trans-DCE to cis-DCE at one well in landfill 3 (6.7) is appreciably above the threshold that can indicate likely solvent release as opposed to TCE degradation alone.

Oxidation-reduction processes in ground water at Naval Weapons Industrial Reserve Plant, Dallas, Texas

USGS Publications Warehouse

Jones, S.A.; Braun, Christopher L.; Lee, Roger W.

2003-01-01

Concentrations of trichloroethene in ground water at the Naval Weapons Industrial Reserve Plant in Dallas, Texas, indicate three source areas of chlorinated solvents?building 1, building 6, and an off-site source west of the facility. The presence of daughter products of reductive dechlorination of trichloroethene, which were not used at the facility, south and southwest of the source areas are evidence that reductive dechlorination is occurring. In places south of the source areas, dissolved oxygen concentrations indicated that reduction of oxygen could be the dominant process, particularly south of building 6; but elevated dissolved oxygen concentrations south of building 6 might be caused by a leaking water or sewer pipe. The nitrite data indicate that denitrification is occurring in places; however, dissolved hydrogen concentrations indicate that iron reduction is the dominant process south of building 6. The distributions of ferrous iron indicate that iron reduction is occurring in places south-southwest of buildings 6 and 1; dissolved hydrogen concentrations generally support the interpretation that iron reduction is the dominant process in those places. The generally low concentrations of sulfide indicate that sulfate reduction is not a key process in most sampled areas, an interpretation that is supported by dissolved hydrogen concentrations. Ferrous iron and dissolved hydrogen concentrations indicate that ferric iron reduction is the primary oxidation-reduction process. Application of mean first-order decay rates in iron-reducing conditions for trichloroethene, dichloroethene, and vinyl chloride yielded half-lives for those solvents of 231, 347, and 2.67 days, respectively. Decay rates, and thus half-lives, at the facility are expected to be similar to those computed. A weighted scoring method to indicate sites where reductive dechlorination might be likely to occur indicated strong evidence for anaerobic biodegradation of chlorinated solvents at six sites. In general, scores were highest for samples collected on the northeast side of the facility.

Activated Persulfate Treatment of 1,4-Dioxane in the Presence of Chlorinated Solvent Co-contaminants

NASA Astrophysics Data System (ADS)

Boving, T. T.; Eberle, D. E. H.; Ball, R.

2014-12-01

1,4-dioxane is an emerging groundwater contaminant and a likely human carcinogen. Due to its history as a stabilizer in chlorinated solvents, 1,4-dioxane is often found as a co-contaminant at solvent releases sites such as landfills, solvent recycling facilities, vapor decreasing operations, and fire-training areas. Historically, 1,4-dioxane was not routinely analyzed for at solvent release sites. The lack of analyses and the limitations of the analyses that were performed (i.e. high reporting limits) means that the scale of 1,4-dioxane subsurface contamination is still emerging. With the number of known 1,4-dioxane sites increasing, the need for cost effective 1,4-dioxane remediation technologies is rising as well. Remediation strategies that are capable of treating both 1,4-dioxane as well as chlorinated co-contaminants are of particular importance, especially when treating mixed-waste source zones. In the present study, we examined the fate of 1,4-dioxane during the targeted remediation of aqueous phase volatile organic compounds (VOC) using an activated persulfate based ISCO method (OxyZone®). Bench scale laboratory experiments are used to evaluate the treatability of 1,4-dioxane both as a single compound and in the presence of trichloroethene (TCE) and 1,1,1-trichloroethane (1,1,1-TCA). Possible dependencies on oxidant concentration and reaction kinetics were studied. Preliminary results are promising and show that OxyZone® is persistent and long lived, with oxidation of 1,4-dioxane continuing more than 12 days after initial dosage, even at dilute oxidant concentrations. The oxidative destruction of 1,4-dioxane, TCE and 1,1,1-TCA in single compound batch systems followed pseudo first order reaction kinetics. The rate of oxidation for each contaminant increased linearly with increasing persulfate concentration over the range of oxidant concentrations tested. The rate of oxidative destruction, from most easily degraded to least was: TCE > 1,4-Dioxane > 1,1,1-TCA. Experiments examining the destruction of 1,4-dioxane in the presence of TCE and 1,1,1-TCA are ongoing. The final results of this study will be presented.

Use of normal propyl bromide solvents for extraction and recovery of asphalt cements

DOT National Transportation Integrated Search

2000-11-01

Four normal propyl bromide (nPB) solvents were evaluated for use as chlorinated solvent replacements in typical hot mix asphalt (HMA) extraction and recovery processes. The experimental design included one method of extraction (centrifuge), one metho...

Emulsified Zero-Valent Nano-Scale Iron Treatment of Chlorinated Solvent DNAPL Source Areas

DTIC Science & Technology

2010-04-01

The EZVI is composed of food-grade surfactant, biodegradable oil , water, and ZVI particles (either nano- or micro-scale iron), which form...emulsion particles (Figure 2-1). Each emulsion particle or droplet contains ZVI particles in water surrounded by an oil -liquid membrane. Since the...exterior oil membrane of the emulsion droplet has hydrophobic properties similar to that of DNAPL, the droplets are miscible with DNAPL. It is believed

Development of a Design Tool for Planning Aqueous Amendment Injection Systems

DTIC Science & Technology

2008-06-01

BIOREMresources.asp) • “Protocol for Enhanced In Situ Bioremediation Using Emulsified Edible Oil” – (search for title at http://docs.serdp-estcp.org...index.cfm) • “Protocol for In Situ Bioremediation of Chlorinated Solvents Using Edible Oil” (http://www.afcee.brooks.af.mil/products/techtrans...and acetate by common subsurface microorganisms . The H2 and acetate are then used as a carbon and energy source for anaerobic biodegradation of the

Used Solvent Testing and Reclamation. Volume 2. Vapor Degreasing and Precision Cleaning Solvents

DTIC Science & Technology

1988-12-01

of 5 to 500 ppm in halogenated solvents using Karl - Fischer reagent. Arbitrary criteria to identify a spent solvent have evolved in various industries... methods of managing waste solvent. Some DOD installations are reclaiming used solvents rather than discarding them. Reclamation is feasible because the...most E E CT E reliable methods for testing solvent quality. Further testing isnecessary for chlorinated solvents to determine the inhibitor con- FEB 24

Direct Push Optical Screening Tool for High-Resolution, Real-Time Mapping of Chlorinated Solvent DNAPL Architecture

DTIC Science & Technology

2016-04-01

due to higher densities, lower viscosities , and increased weathering (mass depletion) of residual chlorinated solvent DNAPL compared to those other...demonstration area can be generally classified as stratified layers of fine sand and silt with few clay layers. A silt layer was penetrated consistently at...toxic and carcinogenic. Another potential issue evaluated was that in plastic soils (stiff clays for example) there is potential for the thickness of

Direct Push Optical Screening Tool for High Resolution, Real-Time Mapping of Chlorinated Solvent DNAPL Architecture

DTIC Science & Technology

2016-07-01

petroleum hydrocarbon fuels due to higher densities, lower viscosities , and increased weathering (mass depletion) of residual chlorinated solvent DNAPL...generally classified as stratified layers of fine sand and silt with few clay layers. A silt layer was penetrated consistently at a depth of about 45...e.g., stiff clays ) there is potential for the thickness of the dye interaction zone to increase to approximately 1-2 mm. Intuition suggests that this

Effect of biosurfactants on the aqueous solubility of PCE and TCE.

PubMed

Albino, John D; Nambi, Indumathi M

2009-12-01

The effect of biosurfactants on the solubility of tetrachloroethylene (PCE) and trichloroethylene (TCE) was studied in batch experiments pertaining to their use for solubilization and mobilization of such contaminants in surfactant enhanced aquifer remediation. Biosurfactants, rhamnolipid and surfactin used in solubility studies were synthesized in our laboratory by Pseudomonas aeruginosa (MTCC 2297) and Bacillus subtilis (MTCC 2423), respectively. The efficiency of the biosurfactants in solubilizing the chlorinated solvents was compared to that of synthetic surfactants. The Weight Solubilization Ratio (WSR) values for solubilization of PCE and TCE by biosurfactants were very high compared to the values obtained for synthetic surfactants. Surfactin proved to be a better surfactant over rhamnolipid. The WSR of surfactin on solubilization of PCE and TCE were 3.83 and 12.5, respectively, whereas the values obtained for rhamnolipid were 2.06 and 8.36. The solubility of the chlorinated solvents by biosurfactants was considerably affected by the changes in pH. The aqueous solubility of PCE and TCE increased tremendously with decrease in pH. The solubility of biosurfactants was observed to decrease with the pH, favoring partitioning of surfactants into the chlorinated solvents in significant amounts at lower pH. The excessive accumulation of biosurfactants at the interface facilitated interfacial tension reductions resulting in higher solubility of the chlorinated solvents at pH less than 7.

Implications of matrix diffusion on 1,4-dioxane persistence at contaminated groundwater sites.

PubMed

Adamson, David T; de Blanc, Phillip C; Farhat, Shahla K; Newell, Charles J

2016-08-15

Management of groundwater sites impacted by 1,4-dioxane can be challenging due to its migration potential and perceived recalcitrance. This study examined the extent to which 1,4-dioxane's persistence was subject to diffusion of mass into and out of lower-permeability zones relative to co-released chlorinated solvents. Two different release scenarios were evaluated within a two-layer aquifer system using an analytical modeling approach. The first scenario simulated a 1,4-dioxane and 1,1,1-TCA source zone where spent solvent was released. The period when 1,4-dioxane was actively loading the low-permeability layer within the source zone was estimated to be <3years due to its high effective solubility. While this was approximately an order-of-magnitude shorter than the loading period for 1,1,1-TCA, the mass of 1,4-dioxane stored within the low-permeability zone at the end of the simulation period (26kg) was larger than that predicted for 1,1,1-TCA (17kg). Even 80years after release, the aqueous 1,4-dioxane concentration was still several orders-of-magnitude higher than potentially-applicable criteria. Within the downgradient plume, diffusion contributed to higher concentrations and enhanced penetration of 1,4-dioxane into the low-permeability zones relative to 1,1,1-TCA. In the second scenario, elevated 1,4-dioxane concentrations were predicted at a site impacted by migration of a weak source from an upgradient site. Plume cutoff was beneficial because it could be implemented in time to prevent further loading of the low-permeability zone at the downgradient site. Overall, this study documented that 1,4-dioxane within transmissive portions of the source zone is quickly depleted due to characteristics that favor both diffusion-based storage and groundwater transport, leaving little mass to treat using conventional means. Furthermore, the results highlight the differences between 1,4-dioxane and chlorinated solvent source zones, suggesting that back diffusion of 1,4-dioxane mass may be serving as the dominant long-term "secondary source" at many contaminated sites that must be managed using alternative approaches. Copyright © 2016 Elsevier B.V. All rights reserved.

Solubility and surface thermodynamics of conducting polymers by inverse gas chromatography. III: polypyrrole chloride.

PubMed

Duaij, Omar K; Alghamdi, Ali; Al-Saigh, Zeki Y

2013-05-24

Inverse gas chromatography, IGC, was applied to characterize conducting polypyrrole chloride (PPyCl) using twenty three solvents. IGC is able to reveal the change in the morphology, the strength of solvent-PPyCl interactions, thermodynamics parameters (χ12, Ω1(∞)), solvent and polymer solubility parameters, and molar heats of sorption, mixing and evaporation (ΔH1(s), ΔH1(∞), ΔH1(v)). The following solvents showed stronger interactions than others; yet, none of these solvents are good solvents for PPyCl: dodecane among the alkane family, tetrahydrofuran and methyl ethyl ketone among the oxy and keto group, dichloromethane among the chlorinated group up to 120°C and chloroform at 180°C, and toluene among the cyclic and aromatic group. Overall, the groups showed higher affinities to PPyCl are: acetates, oxy and cyclic, and chlorinated groups. Comprehensive solvents and PPyCl solubility parameters are obtained. The latter showed that PPyCl is not soluble in any solvent used. Copyright © 2013 Elsevier B.V. All rights reserved.

Method for the synthesis of chlorosilanes

DOEpatents

Wheeler, D.R.; Pollagi, T.P.

1999-08-17

A novel method is described for the synthesis of chlorinated or partially chlorinated organosilanes and organopolysilanes. The chlorination is effected by contacting an organosilanes or organopolysilanes with anhydrous CuCl{sub 2} in a nonpolar alkane solvent, preferably pentane or hexadecane, without the use of a catalyst. Copper metal, which is easily filtered, is a reaction product. The filtrate containing the chlorinated organosilane or organopolysilane can be used directly as a reactant to produce, for example, aminoorganosilanes.

Method for the synthesis of chlorosilanes

DOEpatents

Wheeler, David R.; Pollagi, Timothy P.

1999-01-01

A novel method for the synthesis of chlorinated or partially chlorinated organosilanes and organopolysilanes. The chlorination is effected by contacting an organosilanes or organopolysilanes with anhydrous CuCl.sub.2 in a nonpolar alkane solvent, preferably pentane or hexadecane, without the use of a catalyst. Copper metal, which is easily filtered, is a reaction product. The filtrate containing the chlorinated organosilane or organopolysilane can be used directly as a reactant to produce, for example, aminoorganosilanes.

Microcosm Studies to Evaluate Aerobic Cometabolism of Low Concentrations of 1,4-Dioxane by Isobutane-utilizing Microorganisms in the Presence of Chlorinated Solvent Co-contaminants

NASA Astrophysics Data System (ADS)

Rolston, H. M.; Azizian, M.; Hyman, M. R.; Semprini, L.

2015-12-01

Due to its use as a stabilizer for chlorinated solvents, 1,4-dioxane (1,4D), a probable human carcinogen, is a common co-contaminant in solvent spills at industrial and military sites and landfills. Its persistence in large groundwater plumes at low concentrations makes it a relevant candidate for in-situ bioremediation via cometabolism. Microcosm studies are being performed to evaluate the capability of aerobic microorganisms to cometabolize mixtures of 1,4D and chlorinated solvents, such as trichloroethylene (TCE), 1,1,1-trichloroethane (1,1,1TCA), and 1,1-dichloroethene (1,1DCE), with isobutane as the primary substrate. Microcosms were constructed using aquifer solids from Fort Carson, Colorado, a site contaminated with 1,4D and TCE, to assess the isobutane uptake and transformation of 1,4D and chlorinated solvents by microorganisms native to the site. Additional microcosms were augmented with Rhodococcus rhodochrous, a bacterium shown to cometabolize 1,4D and chlorinated solvents. Results indicate that native microcosms cometabolized 1,4D upon stimulation with isobutane after a lag period of about 15 days. TCE was also transformed, but at significantly slower rates. The presence of 1,4D and TCE at 500 and 300 ppb, respectively, did not inhibit the growth of native microorganisms on isobutane, with isobutane uptake and 1,4D transformation occurring simultaneously. Bioaugmented microcosms transformed 1,4D immediately after inoculation with R. rhodochrous. Tests in bioaugmented microorganisms indicated that the presence of TCE at low concentrations inhibits but does not block the transformation of 1,4D. Results from the microcosms will be used to design field tests to be performed at Fort Carson. Additional microcosm studies will compare the stimulation of native and bioaugmented microcosms and the transformation of mixtures of 1,4D, 1,1,1TCA and 1,1DCE. Molecular methods will analyze the monoxygenase enzymes expressed in the native and bioaugmented microcosms.

Performance of an anaerobic, static bed, fixed film bioreactor for chlorinated solvent treatment

USGS Publications Warehouse

Lorah, Michelle M.; Walker, Charles; Graves, Duane

2015-01-01

Anaerobic, fixed film, bioreactors bioaugmented with a dechlorinating microbial consortium were evaluated as a potential technology for cost effective, sustainable, and reliable treatment of mixed chlorinated ethanes and ethenes in groundwater from a large groundwater recovery system. Bench- and pilot-scale testing at about 3 and 13,500 L, respectively, demonstrated that total chlorinated solvent removal to less than the permitted discharge limit of 100 μg/L. Various planned and unexpected upsets, interruptions, and changes demonstrated the robustness and reliability of the bioreactor system, which handled the operational variations with no observable change in performance. Key operating parameters included an adequately long hydraulic retention time for the surface area, a constant supply of electron donor, pH control with a buffer to minimize pH variance, an oxidation reduction potential of approximately −200 millivolts or lower, and a well-adapted biomass capable of degrading the full suite of chlorinated solvents in the groundwater. Results indicated that the current discharge criteria can be met using a bioreactor technology that is less complex and has less downtime than the sorption based technology currently being used to treat the groundwater.

RECOVERY OF METAL VALUES FROM AQUEOUS SOLUTIONS BY SOLVENT EXTRACTION

DOEpatents

Moore, R.L.

1959-09-01

An organic solvent mixure is described for extracting actinides from aqueous solutions; the solvent mixture consists of from 10 to 25% by volume of tributyl phosphate and the remainder a chlorine-fluorine-substituted saturated hydrocarbon having two carbon atoms in the molecule.

21 CFR 173.290 - Trichloroethylene.

Code of Federal Regulations, 2010 CFR

2010-04-01

... million. Spice oleoresins 30 parts per million (provided that if residues of other chlorinated solvents are also present, the total of all residues of such solvents in spice oleoresins shall not exceed 30...

Improved Monitoring Methods for Performance Assessment During Remediation of DNAPL Source Zones

DTIC Science & Technology

2010-04-01

partitioning behavior of TCE (Schwarzenbach et al. 2003). Kile et al. (1995) determined that the Koc values for two chlorinated solvents in the... Kile et al. (1995) that the sediment organic matter was less polar than the terrestrial material. This difference in polarity was assumed by Kile et al...of reasoning was tested further by Kile et al. (1999), who first related carbon functional group contents of whole soil and sediment samples with

Edible Oil Barriers for Treatment of Chlorinated Solvent Contaminated Groundwater

DTIC Science & Technology

2009-07-01

CF Chloroform Cl# Chlorine Number CO Carbon Monoxide CT Carbon Tetrachloride CVOC Chlorinated Volatile Organic Compound 1,2-DCA 1,2...As Safe HCl Hydrochloric Acid HRC® Hydrogen Release Compound IDW Investigation-Derived Waste ISCO In Situ Chemical Oxidation LEL Lower...Total Organic Carbon VC Vinyl Chloride VFA Volatile Fatty Acid VOC Volatile Organic Compound ZVI Zero Valent Iron viii ACKNOWLEDGEMENTS

Substrate interactions in dehalogenation of 1,2-dichloroethane, 1,2-dichloropropane, and 1,1,2-trichloroethane mixtures by Dehalogenimonas spp.

PubMed

Dillehay, Jacob L; Bowman, Kimberly S; Yan, Jun; Rainey, Fred A; Moe, William M

2014-04-01

When chlorinated alkanes are present as soil or groundwater pollutants, they often occur in mixtures. This study evaluated substrate interactions during the anaerobic reductive dehalogenation of chlorinated alkanes by the type strains of two Dehalogenimonas species, D. lykanthroporepellens and D. alkenigignens. Four contaminant mixtures comprised of combinations of the chlorinated solvents 1,2-dichloroethane (1,2-DCA), 1,2-dichloropropane (1,2-DCP), and 1,1,2-trichloroethane (1,1,2-TCA) were assessed for each species. Chlorinated solvent depletion and daughter product formation determined as a function of time following inoculation into anaerobic media revealed preferential dechlorination of 1,1,2-TCA over both 1,2-DCA and 1,2-DCP for both species. 1,2-DCA in particular was not dechlorinated until 1,1,2-TCA reached low concentrations. In contrast, both species concurrently dechlorinated 1,2-DCA and 1,2-DCP over a comparably large concentration range. This is the first report of substrate interactions during chlorinated alkane dehalogenation by pure cultures, and the results provide insights into the chlorinated alkane transformation processes that may be expected for contaminant mixtures in environments where Dehalogenimonas spp. are present.

21 CFR 173.290 - Trichloroethylene.

Code of Federal Regulations, 2011 CFR

2011-04-01

... extract 10 parts per million. Spice oleoresins 30 parts per million (provided that if residues of other chlorinated solvents are also present, the total of all residues of such solvents in spice oleoresins shall...

Cleaning without chlorinated solvents

NASA Technical Reports Server (NTRS)

Thompson, L. M.; Simandl, R. F.

1995-01-01

Because of health and environmental concerns, many regulations have been passed in recent years regarding the use of chlorinated solvents. The Oak Ridge Y-12 Plant has had an active program to find alternatives for these solvents used in cleaning applications for the past 7 years. During this time frame, the quantity of solvents purchased has been reduced by 92 percent. The program has been a twofold effort. Vapor degreasers used in batch cleaning operations have been replaced by ultrasonic cleaning with aqueous detergent, and other organic solvents have been identified for use in hand-wiping or specialty operations. In order to qualify these alternatives for use, experimentation was conducted on cleaning ability as well as effects on subsequent operations such as welding, painting, and bonding. Cleaning ability was determined using techniques such as x-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) which are capable of examining monolayer levels of contamination on a surface. Solvents have been identified for removal of rust preventative oils, lapping oils, machining coolants, lubricants, greases, and mold releases. Solvents have also been evaluated for cleaning urethane foam spray guns, swelling of urethanes, and swelling of epoxies.

Evaluation of Phytoremediation for Management of Chlorinated Solvents in Soil and Groundwater

EPA Pesticide Factsheets

This document is intended to aid regulators, site owners, consultants, neighbors, and other stakeholders in understanding the proper application of planted systems to remediate groundwater contaminated with halogenated solvents.

Electrokinetic-enhanced bioaugmentation for remediation of chlorinated solvents contaminated clay

PubMed Central

Mao, Xuhui; Wang, James; Ciblak, Ali; Cox, Evan E.; Riis, Charlotte; Terkelsen, Mads; Gent, David B.; Alshawabkeh, Akram N.

2012-01-01

Successful bioremediation of contaminated soils is controlled by the ability to deliver bioremediation additives, such as bacteria and/or nutrients, to the contaminated zone. Because hydraulic advection is not practical for delivery in clays, electrokinetic (EK) injection is an alternative for efficient and uniform delivery of bioremediation additive into low-permeability soil and heterogeneous deposits. EK–enhanced bioaugmentation for remediation of clays contaminated with chlorinated solvents is evaluated. Dehalococcoides (Dhc) bacterial strain and lactate ions are uniformly injected in contaminated clay and complete dechlorination of chlorinated ethene is observed in laboratory experiments. The injected bacteria can survive, grow, and promote effective dechlorination under EK conditions and after EK application. The distribution of Dhc within the clay suggests that electrokinetic transport of Dhc is primarily driven by electroosmosis. In addition to biodegradation due to bioaugmentation of Dhc, an EK-driven transport of chlorinated ethenes is observed in the clay, which accelerates cleanup of chlorinated ethenes from the anode side. Compared with conventional advection-based delivery, EK injection is significantly more effective forestablis hingmicrobial reductive dechlorination capacity in low-permeability soils. PMID:22365139

Preparation of B-trichloroborazine

NASA Technical Reports Server (NTRS)

Riccitiello, Salvatore R.; Hsu, Ming-Ta S.; Chen, Timothy S.

1987-01-01

The present invention relates to a method of preparing B-trichloroborazine. Generally, the method includes the combination of gaseous boron trichloride in an anhydrous aprotic organic solvent followed by addition of excess gaseous ammonia at ambient temperature or below. The reaction mixture is heated to about 100 to 140 C followed by cooling, removal of the solid ammonium chloride at ambient temperature, distillation of the solvent under vacuum if necessary at a temperature of up to about 112 C, and recovery of the B-trichloroborazine. Solvents include toluene, benzene, xylene, chlorinated hydrocarbons, chlorinated aromatic compounds, or mixtures thereof. Toluene is a preferred solvent. The process provides a convenient synthesis of a material which often decomposes on standing. B-trichloroborazine is useful in a number of chemical reactions, and particularly in the formation of high temperature inorganic polymers and polymer precursors.

CHLORINATED SOLVENT CONTAMINATED SOILS AND GROUNDWATER: FIELD APPLICATION OF THE SOLVENT EXTRACTION RESIDUAL BIOTREATMENT TECHNOLOGY

EPA Science Inventory

A pilot scale demonstration of the Solvent Extraction Residual Biotreatment (SERB) technology was conducted at the former Sage's Dry Cleaner site in Jacksonville, FL. The SERB technology is a treatment train approach to complete site restoration, which combines an active in situ...

Use of Nucleic Acid-Based Tools for Monitoring Biostimulation and Bioaugmentation

DTIC Science & Technology

2011-01-01

dechlorination is a promising process for biodegradation of chlorinated solvents. The successful field evaluation and implementation of the reductive...These specialized bacteria use the chlorinated ethenes as electron acceptors and gain energy for growth from the reductive dechlorination reactions...protocol addresses the use of MBTs to quantitatively assess the Dhc population at chlorinated ethene sites and aims at providing guidance to evaluate

Impact Of Landfill Closure Designs On Long-Term Natural Attenuation Of Chlorinated Hydrocarbons

DTIC Science & Technology

2002-03-01

chlorinated aliphatic hydrocarbons (CAHs) (i.e., chlorinated solvents) in landfills and landfill- leachate -contaminated groundwater. The project was divided...attenuation rather than expensive leachate collection and treatment systems. At some landfills, surface infiltration may accelerate the leaching of...the “source” and reduce the time required for biological stabilization of the landfilled waste. Recirculation of landfill leachate could also be

ENHANCED CONCENTRATION AND ANALYSIS METHOD FOR MEASURING WATER SOLUABLE ENDOGENOUS COMPOUNDS IN HUMAN BREATH

EPA Science Inventory

Exhaled human breath analysis has become a standard technique for assessing exposure to exogenous volatile organic compounds (VOCs) such as trihalomethanes from water chlorination; aromatics, hydrocarbons, and oxygenates from fuels usage; and various chlorinated solvents from i...

In Situ Bioremediation of Chlorinated Solvent Source Areas with Enhanced Mass Transfer

DTIC Science & Technology

2008-09-01

immerse in cold water. Do not apply ointment , grease or Vaseline. Cover burns with thick, dry sterile dressings. Keep burned feet or legs elevated...about six to eight barrels per month of waste TCE and POL may have been disposed. These materials were also used to aid in burning other wastes...These consist of man-made fill in the trench areas and include debris and burned material. These materials typically extend to less than 12 ft bgs

40 CFR Table 4 to Subpart Jj of... - Pollutants Excluded From Use in Cleaning and Washoff Solvents

Code of Federal Regulations, 2011 CFR

2011-07-01

... Cleaning and Washoff Solvents 4 Table 4 to Subpart JJ of Part 63 Protection of Environment ENVIRONMENTAL... Cleaning and Washoff Solvents Chemical name CAS No. 4-Aminobiphenyl 92671 Styrene oxide 96093 Diethyl...-chloroethyl) ether) 111444 1,2-Diphenylhydrazine 122667 Toxaphene (chlorinated camphene) 8001352 2,4...

PLANT MULCH TO TREAT TCE IN GROUND WATER IN A PRB

EPA Science Inventory

In the past ten years, passive reactive barriers (PRBs) have found widespread application to treat chlorinated solvent contamination in ground water. The traditional PRB commonly uses granular zero-valent iron and/or iron alloys as filling materials for treatment of chlorinated ...

TRANSECT STUDY OF THE INTRINSIC BIOREMEDIATION TEST PLOT: DOVER AFB

EPA Science Inventory

The work described in this report is part of a project undertaken by the Bioremediation of Chlorinated Solvents Action Team of the Remediation Technologies Development Forum, a joint U.S. Federal agency-industry collaboration, to study the natural attenuation of chlorinated ethen...

Occupational exposure to solvents and risk of head and neck cancer in women: a population-based case-control study in France.

PubMed

Carton, Matthieu; Barul, Christine; Menvielle, Gwenn; Cyr, Diane; Sanchez, Marie; Pilorget, Corinne; Trétarre, Brigitte; Stücker, Isabelle; Luce, Danièle

2017-01-09

Our objective was to investigate the association between head and neck cancer and occupational exposure to chlorinated, oxygenated and petroleum solvents in women. Investigation of occupational and environmental CAuses of REspiratory cancers (ICARE), a French population-based case-control study, included 296 squamous cell carcinomas of the head and neck (HNSCC) in women and 775 female controls. Lifelong occupational history was collected. Job-exposure matrices allowed to assess exposure to 5 chlorinated solvents (carbon tetrachloride; chloroform; methylene chloride; perchloroethylene; trichloroethylene), 5 petroleum solvents (benzene; special petroleum product; gasoline; white spirits and other light aromatic mixtures; diesel, fuels and kerosene) and 5 oxygenated solvents (alcohols; ketones and esters; ethylene glycol; diethyl ether; tetrahydrofuran). OR and 95% CIs, adjusted for smoking, alcohol drinking, age and geographical area, were estimated with logistic models. Elevated ORs were observed among women ever exposed to perchloroethylene (OR=2.97, 95% CI 1.05 to 8.45) and trichloroethylene (OR=2.15, 95% CI 1.21 to 3.81). These ORs increased with exposure duration (OR=3.75, 95% CI 0.64 to 21.9 and OR=4.44, 95% CI 1.56 to 12.6 for 10 years or more, respectively). No significantly increased risk of HNSCC was found for occupational exposure to the other chlorinated, petroleum or oxygenated solvents. These findings suggest that exposure to perchloroethylene or trichloroethylene may increase the risk of HNSCC in women. In our study, there is no clear evidence that the other studied solvents are risk factors for HNSCC. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Occupational exposure to solvents, metals and welding fumes and risk of Parkinson's disease.

PubMed

van der Mark, Marianne; Vermeulen, Roel; Nijssen, Peter C G; Mulleners, Wim M; Sas, Antonetta M G; van Laar, Teus; Huss, Anke; Kromhout, Hans

2015-06-01

The aim of this study was to investigate the potential association between occupational exposure to solvents, metals and/or welding fumes and risk of developing Parkinson's disease (PD). Data of a hospital based case-control study including 444 PD patients and 876 age and sex matched controls was used. Occupational histories and lifestyle information of cases and controls were collected in a structured telephone interview. Exposures to aromatic solvents, chlorinated solvents and metals were estimated by linking the ALOHA+ job-exposure matrix to the occupational histories. Exposure to welding fumes was estimated using self-reported information on welding activities. No statistically significant associations with any of the studied metal and solvent exposures were found. However, for self-reported welding activities we observed non-statistically significant reduced risk estimates (third tertile cumulative exposure: OR = 0.51 (95% CI: 0.21-1.24)). The results of our study did not provide support for an increased chance on developing PD after occupational exposure to aromatic solvents, chlorinated solvents or exposure to metals. The results showed reduced risk estimates for welding, which is in line with previous research, but no clear explanation for these findings is available. Copyright © 2015 Elsevier Ltd. All rights reserved.

Field-scale modeling of acidity production and remediation efficiency during in situ reductive dechlorination

NASA Astrophysics Data System (ADS)

Brovelli, A.; Robinson, C. E.; Barry, D. A.; Gerhard, J.

2009-12-01

Enhanced reductive dechlorination is a viable technology for in situ remediation of chlorinated solvent DNAPL source areas. Although in recent years increased understanding of this technology has led to more rapid dechlorination rates, complete dechlorination can be hindered by unfavorable conditions. Hydrochloric acid produced from dechlorination and organic acids generated from electron donor fermentation can lead to significant groundwater acidification. Adverse pH conditions can inhibit the activity of dehalogenating microorganisms and thus slow or stall the remediation process. The extent of acidification likely to occur at a contaminated site depends on a number of factors including (1) the extent of dechlorination, (2) the pH-sensitivity of dechlorinating bacteria, and (3) the geochemical composition of the soil and water, in particular the soil’s natural buffering capacity. The substantial mass of solvents available for dechlorination when treating DNAPL source zones means that these applications are particularly susceptible to acidification. In this study a reactive transport biogeochemical model was developed to investigate the chemical and physical parameters that control the build-up of acidity and subsequent remediation efficiency. The model accounts for the site water chemistry, mineral precipitation and dissolution kinetics, electron donor fermentation, gas phase formation, competing electron-accepting processes (e.g., sulfate and iron reduction) and the sensitivity of microbial processes to pH. Confidence in the model was achieved by simulating a well-documented field study, for which the 2-D field scale model was able to reproduce long-term variations of pH, and the concurrent build up of reaction products. Sensitivity analyses indicated the groundwater flow velocity is able to reduce acidity build-up when the rate of advection is comparable or larger than the rate of dechlorination. The extent of pH change is highly dependent on the presence of calcite in soil, the availability of competing electron acceptors (in particular dissolved sulfates) and the efficiency with which microbes utilize electron donor. This work is part of SABRE (Source Area BioREmediation), a collaborative international research project that aimed to evaluate and improve enhanced bioremediation of chlorinated solvent source zones.

ENVIRONMENTAL RESEARCH BRIEF: SURFACTANT-ENHANCED DNAPL REMEDIATION: SURFACTANT SELECTION, HYDRAULIC EFFICIENCY, AND ECONOMIC FACTORS

EPA Science Inventory

Chlorinated hydrocarbons are ubiquitous ground water contaminants due to their widespread use as organic solvents and cleaners/degreasers. The immiscibility of chlorinated organis with ground water causes them to exists as nonaqueous phase liquids (NAPLs); this results in their o...

PLANT MULCH TO TREAT TCE IN GROUND WATER IN A PRB (ABSTRACT ONLY)

EPA Science Inventory

In the past ten years, passive reactive barriers (PRBs) have found widespread application to treat chlorinated solvent contamination in ground water. The traditional PRB commonly uses granular zero-valent iron and/or iron alloys as filling materials for treatment of chlorinated ...

Occupational risk factors for urothelial carcinoma: agent-specific results from a case-control study in Germany. MURC Study Group. Multicenter Urothelial and Renal Cancer.

PubMed

Pesch, B; Haerting, J; Ranft, U; Klimpel, A; Oelschlägel, B; Schill, W

2000-04-01

This multicentre population-based case-control study was conducted to estimate the urothelial cancer risk for occupational exposure to aromatic amines, polycyclic aromatic hydrocarbons (PAH), and chlorinated hydrocarbons besides other suspected risk factors. In a population-based multicentre study, 1035 incident urothelial cancer cases and 4298 controls matched for region, sex, and age were interviewed between 1991 and 1995 for their occupational history and lifestyle habits. Exposure to the agents under study was self-assessed as well as expert-rated with two job-exposure matrices and a job task-exposure matrix. Conditional logistic regression was used to calculate smoking adjusted odds ratios (OR) and to control for study centre and age. Urothelial cancer risk following exposure to aromatic amines was only slightly elevated. Among males, substantial exposures to PAH as well as to chlorinated solvents and their corresponding occupational settings were associated with significantly elevated risks after adjustment for smoking (PAH exposure, assessed with a job-exposure matrix: OR = 1.6, 95% CI: 1.1-2.3, exposure to chlorinated solvents, assessed with a job task-exposure matrix: OR = 1.8, 95% CI: 1.2-2.6). Metal degreasing showed an elevated urothelial cancer risk among males (OR = 2.3, 95% CI: 1.4-3.8). In females also, exposure to chlorinated solvents indicated a urothelial cancer risk. Because of small numbers the risk evaluation for females should be treated with caution. Occupational exposure to aromatic amines could not be shown to be as strong a risk factor for urothelial carcinomas as in the past. A possible explanation for this finding is the reduction in exposure over the last 50 years. Our results strengthen the evidence that PAH may have a carcinogenic potential for the urothelium. Furthermore, our results indicate a urothelial cancer risk for the use of chlorinated solvents.

Presence and importance of organochlorine solvents and other compounds in Germany's groundwater and drinking water.

PubMed

Dieter, H H; Kerndorff, H

1993-01-01

Organochlorine compounds are widely used in Germany although the inland production of chlorinated solvents has greatly decreased since 1985. Data on groundwater contamination are incomplete, but there are some regional data sets from the States (Länder). Approximately 25% of the groundwater samples contain more than 1 microgram/l of a single solvent, the most prominent ones being tri- and tetrachloroethene, 1,1,1-trichloroethane and dichloromethane, but also chloroform. The most important causes for contaminations of the groundwater are unprotected storage and leaking sewage systems. Abandoned waste sites are, besides chlorinated compounds, also a source of many other contaminants. A ranking procedure according to their exposure potential (concentration, incidence, toxicology) is proposed. The compound of greatest concern is vinyl chloride, which is formed from tri- and tetrachloroethene under reducing conditions in the subsoil. The most important contaminant in drinking water is tetrachloroethene followed by 1,1,1-trichloroethane and trichloroethane. Chlorobenzene may also be present on occasion, while only about 20% of the finished drinking waters contain more chloroform after treatment than before. Only about 10% of all analyses of drinking water derived from groundwater shows the presence of organochlorine solvents and most of these show total concentrations less than 2 micrograms/l. The degradation product, vinyl chloride, was found up to now only in different groundwaters. To stabilize and to improve the situation, which still is much more favorable for drinking than for groundwater, precautions are going to be taken which should assure that these and other problematic substances which endanger water are used only in closed systems and rigid safety measures be imposed on their disposal and transport.

An assessment of natural biotransformation of petroleum hydrocarbons and chlorinated solvents at an aquifer plume transect

NASA Astrophysics Data System (ADS)

Skubal, Karen L.; Barcelona, Michael J.; Adriaens, Peter

2001-05-01

Field biogeochemical characterization and laboratory microcosm studies were performed to assess the potential for future biotransformation of trichloroethylene (TCE) and toluene in a plume containing petroleum hydrocarbons and chlorinated solvents at the former Wurtsmith Air Force Base in Oscoda, MI. In situ terminal electron accepting processes (TEAPs), contaminant composition and microbial phylogeny were studied at a plume transect 100 m downgradient of the source. The presence of reduced electron acceptors, relevant microbial communities, and elevated dissolved methane and carbon dioxide concentrations at the transect, as well as downgradient accumulation of BTEX metabolites and dechlorination products, indicated that past or current reductive dechlorination at the transect was likely driven by BTEX biodegradation in the methanogenic zone. However, TCE and toluene mineralization in sediment-groundwater microcosms without added electron acceptors did not exceed 5% during 300 days of incubation and was nearly invariant with original sediment TEAP, even following amendments of nitrogen and phosphorus. Mineralization rates were on the order of 0.0015-0.03 μmol/g day. After 8 months, microcosms showed evidence of methanogenesis, but CH 4 and CO 2 production arose from the degradation of contaminants other than toluene. Cis-dichloroethylene was observed in only one methanogenic microcosm after more than 500 days. It appears likely that spatially and temporally dynamic redox zonation at the plume transect will prevent future sustained reductive dehalogenation of highly chlorinated solvents, for during the course of a year, the predominant TEAP at the highly contaminated water table shifted from methanogenesis to iron- and sulfate-reduction. It is recommended that biotransformation studies combine considerations of long-term, spatially relevant changes in redox zonation with laboratory-scale studies of electron donor utilization and cometabolic substrate transformation to yield a more accurate assessment of natural bioattenuation of specific pollutants in aquifers contaminated by undefined organic waste mixtures.

STATISTICAL ANALYSIS OF GROUNDWATER GEOCHEMISTRY DATA FROM AREA 6, DOVER AIR FORCE BASE, DOVER, DELAWARE

EPA Science Inventory

The work described in this report is part of a project undertaken by the Bioremediation of Chlorinated Solvents Action Team of the Remediation Technologies Development Forum, a joint U.S. Federal agency-industry collaboration, to study the natural attenuation of chlorinated ethen...

EFFECTIVE REMOVAL OF TCE IN A LABORATORY MODEL OF A PRB CONSTRUCTED WITH PLANT MULCH

EPA Science Inventory

In the past ten years, passive reactive barriers (PRBs) have found widespread application to treat chlorinated solvent contamination in ground water. The traditional PRB commonly uses granular zero-valent iron and/or iron alloys as filling materials for treatment of chlorinated ...

Alternative acceptance procedures for asphalt mixes.

DOT National Transportation Integrated Search

1992-01-01

By the year 2005, the use of chlorinated solvents is to be eliminated. Faced with this eventuality, VDOT formed a task force to look at alternatives for the acceptance of asphalt mixes. One alternative is to use biodegradable solvents in the extracti...

Design and performance of subgrade biogeochemical reactors.

PubMed

Gamlin, Jeff; Downey, Doug; Shearer, Brad; Favara, Paul

2017-12-15

Subgrade biogeochemical reactors (SBGRs), also commonly referred to as in situ bioreactors, are a unique technology for treatment of contaminant source areas and groundwater plume hot spots. SBGRs have most commonly been configured for enhanced reductive dechlorination (ERD) applications for chlorinated solvent treatment. However, they have also been designed for other contaminant classes using alternative treatment media. The SBGR technology typically consists of removal of contaminated soil via excavation or large-diameter augers, and backfill of the soil void with gravel and treatment amendments tailored to the target contaminant(s). In most cases SBGRs include installation of infiltration piping and a low-flow pumping system (typically solar-powered) to recirculate contaminated groundwater through the SBGR for treatment. SBGRs have been constructed in multiple configurations, including designs capable of meeting limited access restrictions at heavily industrialized sites, and at sites with restrictions on surface disturbance due to sensitive species or habitat issues. Typical performance results for ERD applications include 85 to 90 percent total molar reduction of chlorinated volatile organic compounds (CVOCs) near the SBGR and rapid clean-up of adjacent dissolved contaminant source areas. Based on a review of the literature and CH2M's field-scale results from over a dozen SBGRs with a least one year of performance data, important site-specific design considerations include: 1) hydraulic residence time should be long enough for sufficient treatment but not too long to create depressed pH and stagnant conditions (e.g., typically between 10 and 60 days), 2) reactor material should balance appropriate organic mulch as optimal bacterial growth media along with other organic additives that provide bioavailable organic carbon, 3) a variety of native bacteria are important to the treatment process, and 4) biologically mediated generation of iron sulfides along with addition of iron pyrite sands as an abiotic polishing step within the reactor has been observed to be an efficient treatment train for chlorinated solvent sites. Copyright © 2017 Elsevier Ltd. All rights reserved.

I{ Relationship between source clean up and mass flux of chlorinated solvents in low permeability settings with fractures}

NASA Astrophysics Data System (ADS)

Bjerg, P. L.; Chambon, J. C.; Christiansen, C. M.; Broholm, M. M.; Binning, P. J.

2009-04-01

Groundwater contamination by chlorinated solvents, such as perchloroethylene (PCE), often occurs via leaching from complex sources located in low permeability sediments such as clayey tills overlying aquifers. Clayey tills are mostly fractured, and contamination migrating through the fractures spreads to the low permeability matrix by diffusion. This results in a long term source of contamination due to back-diffusion. Leaching from such sources is further complicated by microbial degradation under anaerobic conditions to sequentially form the daughter products trichloroethylene, cis-dichloroethylene (cis-DCE), vinyl chloride (VC) and ethene. This process can be enhanced by addition of electron donors and/or bioaugmentation and is termed Enhanced Reductive Dechlorination (ERD). This work aims to improve our understanding of the physical, chemical and microbial processes governing source behaviour under natural and enhanced conditions. That understanding is applied to risk assessment, and to determine the relationship and time frames of source clean up and plume response. To meet that aim, field and laboratory observations are coupled to state of the art models incorporating new insights of contaminant behaviour. The long term leaching of chlorinated ethenes from clay aquitards is currently being monitored at a number of Danish sites. The observed data is simulated using a coupled fracture flow and clay matrix diffusion model. Sequential degradation is represented by modified Monod kinetics accounting for competitive inhibition between the chlorinated ethenes. The model is constructed using Comsol Multiphysics, a generic finite- element partial differential equation solver. The model is applied at well characterised field sites with respect to hydrogeology, fracture network, contaminant distribution and microbial processes (lab and field experiments). At one of the study sites (Sortebrovej), the source areas are situated in a clayey till with fractures and interbedded sand lenses. The site is highly contaminated with chlorinated ethenes which impact the underlying sand aquifer. Full scale remediation using ERD was implemented at Sortebrovej in 2006. Anaerobic dechlorination is taking place, and cis-DCE and VC have been found in significant amounts in monitoring wells and to some degree in sediment cores representing the the clayey till matrix. Model results reveal several interesting findings. The physical processes of matrix diffusion and advection in the fractures seem to be more important than the microbial degradation processes for estimation of the time frames and the distance between fractures is amongst the most sensitive model parameters. However, the inclusion of sequential degradation is crucial to determining the composition of contamination leaching into the underlying aquifer. Degradation products like VC will peak at an earlier stage compared to the mother compound due to a higher mobility. These model results are supported by actual findings at the Sortebrovej site. The findings highlight a need for improved characterization of low permeability aquitards lying above aquifers used for water supply. The fracture network in aquitards is currently poorly described at larger depths (below 5-8 m) and the effect of sand lenses on leaching behaviour is not well understood. The microbial processes are assumed to be taking place in the fracture system, but the interaction with and processes in the matrix need to be further explored. Development of new methods for field site characterisation and integrated field and model expertise are crucial for the design of remedial actions and for risk assessment of contaminated sites in low permeability settings.

Long Term Leaching of Chlorinated Solvents from Source Zones in Low Permeability Settings with Fractures

NASA Astrophysics Data System (ADS)

Bjerg, P. L.; Chambon, J.; Troldborg, M.; Binning, P. J.; Broholm, M. M.; Lemming, G.; Damgaard, I.

2008-12-01

Groundwater contamination by chlorinated solvents, such as perchloroethylene (PCE), often occurs via leaching from complex sources located in low permeability sediments such as clayey tills overlying aquifers. Clayey tills are mostly fractured, and contamination migrating through the fractures spreads to the low permeability matrix by diffusion. This results in a long term source of contamination due to back-diffusion. Leaching from such sources is further complicated by microbial degradation under anaerobic conditions to sequentially form the daughter products trichloroethylene, cis-dichloroethylene (cis-DCE), vinyl chloride (VC) and ethene. This process can be enhanced by addition of electron donors and/or bioaugmentation and is termed Enhanced Reductive Dechlorination (ERD). This work aims to improve our understanding of the physical, chemical and microbial processes governing source behaviour under natural and enhanced conditions. That understanding is applied to risk assessment, and to determine the relationship and time frames of source clean up and plume response. To meet that aim, field and laboratory observations are coupled to state of the art models incorporating new insights of contaminant behaviour. The long term leaching of chlorinated ethenes from clay aquitards is currently being monitored at a number of Danish sites. The observed data is simulated using a coupled fracture flow and clay matrix diffusion model. Sequential degradation is represented by modified Monod kinetics accounting for competitive inhibition between the chlorinated ethenes. The model is constructed using Comsol Multiphysics, a generic finite- element partial differential equation solver. The model is applied at two well characterised field sites with respect to hydrogeology, fracture network, contaminant distribution and microbial processes (lab and field experiments). At the study sites (Sortebrovej and Vadsbyvej), the source areas are situated in a clayey till with fractures and interbedded sand lenses. The field sites are both highly contaminated with chlorinated ethenes which impact the underlying sand aquifer. Anaerobic dechlorination is taking place, and cis-DCE and VC have been found in significant amounts in the matrix. Full scale remediation using ERD was implemented at Sortebrovej in 2006, and ERD has been suggested as a remedy at Vadsbyvej. Results reveal several interesting findings. The physical processes of matrix diffusion and advection in the fractures seem to be more important than the microbial degradation processes for estimation of the time frames and the distance between fractures is amongst the most sensitive model parameters. However, the inclusion of sequential degradation is crucial to determining the composition of contamination leaching into the underlying aquifer. Degradation products like VC will peak at an earlier stage compared to the mother compound due to a higher mobility. The findings highlight a need for improved characterization of low permeability aquitards lying above aquifers used for water supply. The fracture network in aquitards is currently poorly described at larger depths (below 5-8 m) and the effect of sand lenses on leaching behaviour is not well understood. The microbial processes are assumed to be taking place in the fracture system, but the interaction with and processes in the matrix need to be further explored. Development of new methods for field site characterisation and integrated field and model expertise are crucial for the design of remedial actions and for risk assessment of contaminated sites in low permeability settings.

BIOCHLOR: NATURAL ATTENUATION DECISION SUPPORT SYSTEM, USER'S MANUAL, VERSION 1.0

EPA Science Inventory

BIOCHLOR is an easy-to-use screening model that simulates remediation by natural attenuation (RNA) of dissolved solvents at chlorinated solvent release sites. The software, programmed in the Microsoft Excel spreadsheet environment and based on the Domenico analytical solute tran...

Tyrosine 192 in apolipoprotein A-I is the major site of nitration and chlorination by myeloperoxidase, but only chlorination markedly impairs ABCA1-dependent cholesterol transport.

PubMed

Shao, Baohai; Bergt, Constanze; Fu, Xiaoyun; Green, Pattie; Voss, John C; Oda, Michael N; Oram, John F; Heinecke, Jay W

2005-02-18

High density lipoprotein (HDL) isolated from human atherosclerotic lesions and the blood of patients with established coronary artery disease contains elevated levels of 3-nitrotyrosine and 3-chlorotyrosine. Myeloperoxidase (MPO) is the only known source of 3-chlorotyrosine in humans, indicating that MPO oxidizes HDL in vivo. In the current studies, we used tandem mass spectrometry to identify the major sites of tyrosine oxidation when lipid-free apolipoprotein A-I (apoA-I), the major protein of HDL, was exposed to MPO or peroxynitrite (ONOO(-)). Tyrosine 192 was the predominant site of both nitration and chlorination by MPO and was also the major site of nitration by ONOO(-). Electron paramagnetic spin resonance studies of spin-labeled apoA-I revealed that residue 192 was located in an unusually hydrophilic environment. Moreover, the environment of residue 192 became much more hydrophobic when apoA-I was incorporated into discoidal HDL, and Tyr(192) of HDL-associated apoA-I was a poor substrate for nitration by both myeloperoxidase and ONOO(-), suggesting that solvent accessibility accounted in part for the reactivity of Tyr(192). The ability of lipid-free apoA-I to facilitate ATP-binding cassette transporter A1 cholesterol transport was greatly reduced after chlorination by MPO. Loss of activity occurred in concert with chlorination of Tyr(192). Both ONOO(-) and MPO nitrated Tyr(192) in high yield, but unlike chlorination, nitration minimally affected the ability of apoA-I to promote cholesterol efflux from cells. Our results indicate that Tyr(192) is the predominant site of nitration and chlorination when MPO or ONOO(-) oxidizes lipid-free apoA-I but that only chlorination markedly reduces the cholesterol efflux activity of apoA-I. This impaired biological activity of chlorinated apoA-I suggests that MPO-mediated oxidation of HDL might contribute to the link between inflammation and cardiovascular disease.

Occupational exposures to solvents and metals are associated with fixed airflow obstruction.

PubMed

Alif, Sheikh M; Dharmage, Shyamali C; Benke, Geza; Dennekamp, Martine; Burgess, John A; Perret, Jennifer L; Lodge, Caroline J; Morrison, Stephen; Johns, David P; Giles, Graham G; Gurrin, Lyle C; Thomas, Paul S; Hopper, John L; Wood-Baker, Richard; Thompson, Bruce R; Feather, Iain H; Vermeulen, Roel; Kromhout, Hans; Walters, E Haydn; Abramson, Michael J; Matheson, Melanie C

2017-11-01

Objectives This study investigated the associations between occupational exposures to solvents and metals and fixed airflow obstruction (AO) using post-bronchodilator spirometry. Methods We included 1335 participants from the 2002-2008 follow-up of the Tasmanian Longitudinal Health Study. Ever-exposure and cumulative exposure-unit (EU) years were calculated using the ALOHA plus job exposure matrix (JEM). Fixed AO was defined as post-bronchodilator forced expiratory volume in one second (FEV1)/forced vital capacity (FVC) <0.7 and FEV 1 /FVC

IN-SITU DUOX™ CHEMICAL OXIDATION TECHNOLOGY TO TREAT CHLORINATED ORGANICS AT THE ROOSEVELT MILLS SITE, VERNON, CT: SITE CHARACTERIZATION AND TREATABILITY STUDY

EPA Science Inventory

A study was performed investigating the feasibility of applying the DUOX™ chemical oxidation technology to chlorinated solvent contaminated media at the Roosevelt Mills site in Vernon, Connecticut. The Roosevelt Mills site is a former woolen mill that included dry cleaning operat...

EXTRACTION OF SEDIMENT-BOUND CHLORINATED ORGANIC COMPOUNDS: IMPLICATIONS ON FATE AND HAZARD ASSESSMENT. (R825513C007)

EPA Science Inventory

Five methods were used for the extraction of hexachlorobutadiene and chlorobenzenes from a contaminated estuarine sediment. The following extraction methods were used: Soxhlet extraction, sonication and solvent extraction, sequential solvent extraction, saponification and solv...

IRIS TOXICOLOGICAL REVIEW AND SUMMARY DOCUMENTS FOR 1,4 - DIOXANE

EPA Science Inventory

1,4 -Dioxane is a cyclic ether that is primarily utilized for industrial applications. These applications include 1,4 -dioxane as a solvent, reaction medium, wetting, degreasing, and dispersing agent, and for stabilization of chlorinated solvents (e.g. 1,1,1 -trichloroethane). ...

Temporal variations in parameters reflecting terminal-electron-accepting processes in an aquifer contaminated with waste fuel and chlorinated solvents

USGS Publications Warehouse

McGuire, Jennifer T.; Smith, Erik W.; Long, David T.; Hyndman, David W.; Haack, Sheridan K.; Klug, Michael J.; Velbel, Michael A.

2000-01-01

A fundamental issue in aquifer biogeochemistry is the means by which solute transport, geochemical processes, and microbiological activity combine to produce spatial and temporal variations in redox zonation. In this paper, we describe the temporal variability of TEAP conditions in shallow groundwater contaminated with both waste fuel and chlorinated solvents. TEAP parameters (including methane, dissolved iron, and dissolved hydrogen) were measured to characterize the contaminant plume over a 3-year period. We observed that concentrations of TEAP parameters changed on different time scales and appear to be related, in part, to recharge events. Changes in all TEAP parameters were observed on short time scales (months), and over a longer 3-year period. The results indicate that (1) interpretations of TEAP conditions in aquifers contaminated with a variety of organic chemicals, such as those with petroleum hydrocarbons and chlorinated solvents, must consider additional hydrogen-consuming reactions (e.g., dehalogenation); (2) interpretations must consider the roles of both in situ (at the sampling point) biogeochemical and solute transport processes; and (3) determinations of microbial communities are often necessary to confirm the interpretations made from geochemical and hydrogeological measurements on these processes.

A study of chlorinated solvent contamination of the aquifers of an industrial area in central Italy: a possibility of bioremediation

PubMed Central

Matteucci, Federica; Ercole, Claudia; del Gallo, Maddalena

2015-01-01

Perchloroethene, trichloroethene, and other chlorinated solvents are widespread groundwater pollutants. They form dense non-aqueous phase liquids that sink through permeable groundwater aquifers until non-permeable zone is reached. In Italy, there are many situations of serious contamination of groundwater that might compromise their use in industry, agriculture, private, as the critical case of a Central Italy valley located in the province of Teramo (“Val Vibrata”), characterized by a significant chlorinated solvents contamination. Data from the various monitoring campaigns that have taken place over time were collected, and new samplings were carried out, resulting in a complete database. The data matrix was processed with a multivariate statistic analysis (in particular principal component analysis, PCA) and was then imported into geographic information system (GIS), to obtain a model of the contamination. A microcosm anaerobic study was utilized to assess the potential for in situ natural or enhanced bioremediation. Most of the microcosms were positive for dechlorination, particularly those inoculated with a mineral medium. This indicate the presence of an active native dechlorinating population in the subsurface, probably inhibited by co-contaminants in the groundwater, or more likely by the absence or lack of nutritional factors. Among the tested electron donors (i.e., yeast extract, lactate, and butyrate) lactate and butyrate enhanced dechlorination of chlorinated compounds. PCA and GIS studies allowed delimiting the contamination; the microcosm study helped to identify the conditions to promote the bioremediation of the area. PMID:26388862

Synthetic oligomer analysis using atmospheric pressure photoionization mass spectrometry at different photon energies.

PubMed

Desmazières, Bernard; Legros, Véronique; Giuliani, Alexandre; Buchmann, William

2014-01-15

Atmospheric pressure photoionization (APPI) followed by mass spectrometric detection was used to ionize a variety of polymers: polyethylene glycol, polymethyl methacrylate, polystyrene, and polysiloxane. In most cases, whatever the polymer or the solvent used (dichloromethane, tetrahydrofuran, hexane, acetone or toluene), only negative ion mode produced intact ions such as chlorinated adducts, with no or few fragmentations, in contrast to the positive ion mode that frequently led to important in-source fragmentations. In addition, it was shown that optimal detection of polymer distributions require a fine tuning of other source parameters such as temperature and ion transfer voltage. Series of mass spectra were recorded in the negative mode, in various solvents (dichloromethane, tetrahydrofuran, hexane, toluene, and acetone), by varying the photon energy from 8eV up to 10.6eV using synchrotron radiation. To these solvents, addition of a classical APPI dopant (toluene or acetone) was not necessary. Courtesy of the synchrotron radiation, it was demonstrated that the photon energy required for an efficient ionization of the polymer was correlated to the ionization energy of the solvent. As commercial APPI sources typically use krypton lamps with energy fixed at 10eV and 10.6eV, the study of the ionization of polymers over a wavelength range allowed to confirm and refine the previously proposed ionization mechanisms. Moreover, the APPI source can efficiently be used as an interface between size exclusion chromatography or reverse phase liquid chromatography and MS for the study of synthetic oligomers. However, the photoionization at fixed wavelength of polymer standards with different molecular weights showed that it was difficult to obtain intact ionized oligomers with molecular weights above a few thousands. Copyright © 2013 Elsevier B.V. All rights reserved.

Anaerobic oxidation of [1,2-14C]Dichloroethene under Mn(IV)-reducing conditions

USGS Publications Warehouse

Bradley, Paul M.; Landmeyer, James E.; Dinicola, Richard S.

1998-01-01

Anaerobic oxidation of [1,2-14C]dichloroethene to14CO2 under Mn(IV)-reducing conditions was demonstrated. The results indicate that oxidative degradation of partially chlorinated solvents like dichloroethene can be significant even under anoxic conditions and demonstrate the potential importance of Mn(IV) reduction for remediation of chlorinated groundwater contaminants.

Analytical method for optimal source reduction with monitored natural attenuation in contaminated aquifers

USGS Publications Warehouse

Widdowson, M.A.; Chapelle, F.H.; Brauner, J.S.; ,

2003-01-01

A method is developed for optimizing monitored natural attenuation (MNA) and the reduction in the aqueous source zone concentration (??C) required to meet a site-specific regulatory target concentration. The mathematical model consists of two one-dimensional equations of mass balance for the aqueous phase contaminant, to coincide with up to two distinct zones of transformation, and appropriate boundary and intermediate conditions. The solution is written in terms of zone-dependent Peclet and Damko??hler numbers. The model is illustrated at a chlorinated solvent site where MNA was implemented following source treatment using in-situ chemical oxidation. The results demonstrate that by not taking into account a variable natural attenuation capacity (NAC), a lower target ??C is predicted, resulting in unnecessary source concentration reduction and cost with little benefit to achieving site-specific remediation goals.

Complementing approaches to demonstrate chlorinated solvent biodegradation in a complex pollution plume: Mass balance, PCR and compound-specific stable isotope analysis

NASA Astrophysics Data System (ADS)

Courbet, Christelle; Rivière, Agnès; Jeannottat, Simon; Rinaldi, Sandro; Hunkeler, Daniel; Bendjoudi, Hocine; de Marsily, Ghislain

2011-11-01

This work describes the use of different complementing methods (mass balance, polymerase chain reaction assays and compound-specific stable isotope analysis) to demonstrate the existence and effectiveness of biodegradation of chlorinated solvents in an alluvial aquifer. The solvent-contaminated site is an old chemical factory located in an alluvial plain in France. As most of the chlorinated contaminants currently found in the groundwater at this site were produced by local industries at various times in the past, it is not enough to analyze chlorinated solvent concentrations along a flow path to convincingly demonstrate biodegradation. Moreover, only a few data were initially available to characterize the geochemical conditions at this site, which were apparently complex at the source zone due to (i) the presence of a steady oxygen supply to the groundwater by irrigation canal losses and river infiltration and (ii) an alkaline pH higher than 10 due to former underground lime disposal. A demonstration of the existence of biodegradation processes was however required by the regulatory authority within a timeframe that did not allow a full geochemical characterization of such a complex site. Thus a combination of different fast methods was used to obtain a proof of the biodegradation occurrence. First, a mass balance analysis was performed which revealed the existence of a strong natural attenuation process (biodegradation, volatilization or dilution), despite the huge uncertainty on these calculations. Second, a good agreement was found between carbon isotopic measurements and PCR assays (based on 16S RNA gene sequences and functional genes), which clearly indicated reductive dechlorination of different hydrocarbons (Tetrachloroethene—PCE-, Trichloroethene—TCE-, 1,2- cisDichloroethene— cis-1,2-DCE-, 1,2- transDichloroethene— trans-1,2-DCE-, 1,1-Dichloroethene—1,1-DCE-, and Vinyl Chloride—VC) to ethene. According to these carbon isotope measurements, although TCE biodegradation seems to occur only in the upgradient part of the studied zone, DCE and VC dechlorination (originating from the initial TCE dechlorination) occurs along the entire flowpath. TCE reductase was not detected among the Dehalococcoides bacteria identified by quantitative PCR (qPCR), while DCE and VC reductases were present in the majority of the population. Reverse transcriptase PCR assays (rt-PCR) also indicated that bacteria and their DCE and VC reductases were active. Mass balance calculations showed moreover that 1,1-DCE was the predominant DCE isomer produced by TCE dechlorination in the upgradient part of the site. Consequently, coupling rt-PCR assays with isotope measurements removes the uncertainties inherent in a simple mass balance approach, so that when the three methods are used jointly, they allow the identification and quantification of natural biodegradation, even under apparently complex geochemical and hydraulic conditions.

Statistical modeling of occupational chlorinated solvent exposures for case–control studies using a literature-based database

PubMed Central

Hein, Misty J.; Waters, Martha A.; Ruder, Avima M.; Stenzel, Mark R.; Blair, Aaron; Stewart, Patricia A.

2010-01-01

Objectives: Occupational exposure assessment for population-based case–control studies is challenging due to the wide variety of industries and occupations encountered by study participants. We developed and evaluated statistical models to estimate the intensity of exposure to three chlorinated solvents—methylene chloride, 1,1,1-trichloroethane, and trichloroethylene—using a database of air measurement data and associated exposure determinants. Methods: A measurement database was developed after an extensive review of the published industrial hygiene literature. The database of nearly 3000 measurements or summary measurements included sample size, measurement characteristics (year, duration, and type), and several potential exposure determinants associated with the measurements: mechanism of release (e.g. evaporation), process condition, temperature, usage rate, type of ventilation, location, presence of a confined space, and proximity to the source. The natural log-transformed measurement levels in the exposure database were modeled as a function of the measurement characteristics and exposure determinants using maximum likelihood methods. Assuming a single lognormal distribution of the measurements, an arithmetic mean exposure intensity level was estimated for each unique combination of exposure determinants and decade. Results: The proportions of variability in the measurement data explained by the modeled measurement characteristics and exposure determinants were 36, 38, and 54% for methylene chloride, 1,1,1-trichloroethane, and trichloroethylene, respectively. Model parameter estimates for the exposure determinants were in the anticipated direction. Exposure intensity estimates were plausible and exhibited internal consistency, but the ability to evaluate validity was limited. Conclusions: These prediction models can be used to estimate chlorinated solvent exposure intensity for jobs reported by population-based case–control study participants that have sufficiently detailed information regarding the exposure determinants. PMID:20418277

Recycling of Rare Earth Elements

NASA Astrophysics Data System (ADS)

Lorenz, Tom; Bertau, Martin

2017-01-01

Any development of an effective process for rare earth (RE) recycling has become more and more challenging, especially in recent years. Since 2011, when commodity prices of REs had met their all-time maximum, prices have dropped rapidly by more than 90 %. An economic process able to offset these fluctuations has to take unconventional methods into account beside well-known strategies like acid/basic leaching or solvent extraction. The solid-state chlorination provides such an unconventional method for mobilizing RE elements from waste streams. Instead of hydrochloric acid this kind of chlorination decomposes NH4Cl thermally to release up to 400 °C hot HCl gas. After cooling the resulting solid metal chlorides may be easily dissolved in pH-adjusted water. Without producing strongly acidic wastes and with NH4Cl as cheap source for hydrogen chloride, solid-state chlorination provides various advantages in terms of costs and disposal. In the course of the SepSELSA project this method was examined, adjusted and optimized for RE recycling from fluorescent lamp scraps as well as Fe14Nd2B magnets. Thereby many surprising influences and trends required various analytic methods to examine the reasons and special mechanisms behind them.

Solvents and Parkinson disease: A systematic review of toxicological and epidemiological evidence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lock, Edward A., E-mail: e.lock@ljmu.ac.uk; Zhang, Jing; Checkoway, Harvey

2013-02-01

Parkinson disease (PD) is a debilitating neurodegenerative motor disorder, with its motor symptoms largely attributable to loss of dopaminergic neurons in the substantia nigra. The causes of PD remain poorly understood, although environmental toxicants may play etiologic roles. Solvents are widespread neurotoxicants present in the workplace and ambient environment. Case reports of parkinsonism, including PD, have been associated with exposures to various solvents, most notably trichloroethylene (TCE). Animal toxicology studies have been conducted on various organic solvents, with some, including TCE, demonstrating potential for inducing nigral system damage. However, a confirmed animal model of solvent-induced PD has not been developed.more » Numerous epidemiologic studies have investigated potential links between solvents and PD, yielding mostly null or weak associations. An exception is a recent study of twins indicating possible etiologic relations with TCE and other chlorinated solvents, although findings were based on small numbers, and dose–response gradients were not observed. At present, there is no consistent evidence from either the toxicological or epidemiologic perspective that any specific solvent or class of solvents is a cause of PD. Future toxicological research that addresses mechanisms of nigral damage from TCE and its metabolites, with exposure routes and doses relevant to human exposures, is recommended. Improvements in epidemiologic research, especially with regard to quantitative characterization of long-term exposures to specific solvents, are needed to advance scientific knowledge on this topic. -- Highlights: ► The potential for organic solvents to cause Parkinson's disease has been reviewed. ► Twins study suggests etiologic relations with chlorinated solvents and Parkinson's. ► Animal studies with TCE showed potential to cause damage to dopaminergic neurons. ► Need to determine if effects in animals are relevant to human exposure levels.« less

Characterization of Chlorinated Solvent Degradation Profile Due to Microbial and Chemical Processes in a Constructed Wetland

DTIC Science & Technology

2004-03-01

Natural Attenuation…………………………………………………………………..10 Phytoremediation and Biodegradation……………………………………………….11 Microbial Growth...84 ix List of Figures Figure Page 1. Processes in Phytoremediation ……………………………………………………….13 2. Known Pathway of...produced and used in the United States for nearly a century. The production of chlorinated solvents began in the early nineteenth century in Germany

Mechanistic insights into the one-pot synthesis of propargylamines from terminal alkynes and amines in chlorinated solvents catalyzed by gold compounds and nanoparticles.

PubMed

Aguilar, David; Contel, Maria; Urriolabeitia, Esteban P

2010-08-09

Propargylamines can be obtained from secondary amines and terminal alkynes in chlorinated solvents by a three- and two-component synthesis catalyzed by gold compounds and nanoparticles (Au-NP) under mild conditions. The use of dichloromethane allows for the activation of two C-Cl bonds and a clean transfer of the methylene fragment to the final product. The scope of the reaction as well as the influence of different gold(III) cycloaurated complexes and salts has been investigated. The involvement of gold nanoparticles generated in situ in the process is discussed and a plausible reaction mechanism is proposed on the basis of the data obtained.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kin, B.; Dincer, S.; Kuyulu, A.

The authors report the reduction and removal of sulfur compounds from Can K{sub 4}, Keles and Agacli lignite samples, obtained from mines close to Istanbul, studied using chlorine gas. Water or mixtures of methyl chloroform-water and carbon tetrachloride-water were used as solvents. Chlorine gas was bubbled through a suspension of lignite sample in solvent for about 1 to 5 hrs. It was observed that removal of sulfur increased with increasing time. Chlorinolysis and the Meyers method were used separately to compare their effects on the reduction of sulfur from Agacli and Keles lignite samples. Chlorinolysis was found to be moremore » effective than the Meyers method in the removal of organic sulfur and thus the total sulfur.« less

Impact of Ammonium on Syntrophic Organohalide-Respiring and Fermenting Microbial Communities

PubMed Central

Fajardo-Williams, Devyn; Kegerreis, Kylie L.; Parameswaran, Prathap

2016-01-01

ABSTRACT Syntrophic interactions between organohalide-respiring and fermentative microorganisms are critical for effective bioremediation of halogenated compounds. This work investigated the effect of ammonium concentration (up to 4 g liter−1 NH4+-N) on trichloroethene-reducing Dehalococcoides mccartyi and Geobacteraceae in microbial communities fed lactate and methanol. We found that production of ethene by D. mccartyi occurred in mineral medium containing ≤2 g liter−1 NH4+-N and in landfill leachate. For the partial reduction of trichloroethene (TCE) to cis-dichloroethene (cis-DCE) at ≥1 g liter−1 NH4+-N, organohalide-respiring dynamics shifted from D. mccartyi and Geobacteraceae to mainly D. mccartyi. An increasing concentration of ammonium was coupled to lower metabolic rates, longer lag times, and lower gene abundances for all microbial processes studied. The methanol fermentation pathway to acetate and H2 was conserved, regardless of the ammonium concentration provided. However, lactate fermentation shifted from propionic to acetogenic at concentrations of ≥2 g liter−1 NH4+-N. Our study findings strongly support a tolerance of D. mccartyi to high ammonium concentrations, highlighting the feasibility of organohalide respiration in ammonium-contaminated subsurface environments. IMPORTANCE Contamination with ammonium and chlorinated solvents has been reported in numerous subsurface environments, and these chemicals bring significant challenges for in situ bioremediation. Dehalococcoides mccartyi is able to reduce the chlorinated solvent trichloroethene to the nontoxic end product ethene. Fermentative bacteria are of central importance for organohalide respiration and bioremediation to provide D. mccartyi with H2, their electron donor, acetate, their carbon source, and other micronutrients. In this study, we found that high concentrations of ammonium negatively correlated with rates of trichloroethene reductive dehalogenation and fermentation. However, detoxification of trichloroethene to nontoxic ethene occurred even at ammonium concentrations typical of those found in animal waste (up to 2 g liter−1 NH4+-N). To date, hundreds of subsurface environments have been bioremediated through the unique metabolic capability of D. mccartyi. These findings extend our knowledge of D. mccartyi and provide insight for bioremediation of sites contaminated with chlorinated solvents and ammonium. PMID:27303735

Annual Report to Congress, Fiscal Year 1997. A Report by The Council of the Strategic Environmental Research and Development Program

DTIC Science & Technology

1998-03-01

Discovery of Novel Enzymatic Reactions and Determination of Biodegradation Mechanisms and Pathways. b. Phytoremediation of Explosives Contaminated...Groundwater using Wetlands and Aquatic Plants. c. Phytoremediation of Munitions Contaminated Soils. d. Enhanced TNT Biodegradation Through Genetic Manipulation...Microbial Communities Active in the Enhanced Aerobic Treatment of Chlorinated Ethenes. c. Phytoremediation of Shallow Chlorinated Solvent Plumes

Long term impacts of CMC/nZVI amendment injection on organohalide-respiring microbial communities at a chlorinated solvent field site

NASA Astrophysics Data System (ADS)

Kocur, C. M.; Lomheim, L.; Boparai, H. K.; Chowdhury, A. I.; Weber, K.; Austrins, L. M.; Sleep, B.; O'Carroll, D. M.; Edwards, E.

2014-12-01

Injection of carboxymethyl-cellulose stabilized nanoscale Zero Valent Iron (CMC/nZVI) has received significant attention in the last decade as an emerging alternative for in-situ remediation of chlorinated solvents and other recalcitrant compounds. There has also been some indication that injection of nZVI will create conditions that will stimulate in-situ microbial populations, leading to further contaminant degradation. Carboxy-methyl cellulose (CMC) is commonly used for nZVI synthesis as it provides steric stabilization for the nanoparticles, however, the CMC is equally important as a subsurface amendment as it may act as a fermentable substrate for microorganisms in-situ. In this study, microbial communities were monitored over a 2.5 year period following the injection of CMC/nZVI at a chlorinated solvent remediation site. Dehalococcoides spp. genetic markers and vinyl chloride reductase genes (vcrA) were targeted in the 16s RNA using quantitative polymerase chain reaction (qPCR). This analysis was complimented with a suite of aqueous chlorinated ethene, ethane, and methane compounds to monitor degradation. Following the injection of CMC/nZVI a decline of parent chlorinated compound concentrations was observed as well as the emergence of daughter products. A period of abiotic nZVI oxidation is believed to be responsible for a portion of the degradation at the site, however, a prolonged period of contaminant degradation followed and is believed to be the result of organohalide-respiring microorganisms native to the site. Further analysis was performed on the microbial samples using 454 pyrotag sequencing of amplified 16S rRNA genes to obtain the genetic profile of the microbial community. Of particular interest within this large genomic profile is the characterization of the stable population of important organohalide-respiring microorganisms on site. Results suggest that there is a distinctly different response in the organohalide-respiring microbial community in areas of the site where CMC/nZVI amendments were injected compared to a background response.

Contamination in fractured-rock aquifers: Research at the former Naval Air Warfare Center, West Trenton, New Jersey

USGS Publications Warehouse

Goode, Daniel J.; Tiedeman, Claire; Lacombe, Pierre J.; Imbrigiotta, Thomas E.; Shapiro, Allen M.; Chapelle, Francis H.

2007-01-01

The U.S. Geological Survey and cooperators are studying chlorinated solvents in a fractured sedimentary rock aquifer underlying the former Naval Air Warfare Center (NAWC), West Trenton, New Jersey. Fractured-rock aquifers are common in many parts of the United States and are highly susceptible to contamination, particularly at industrial sites. Compared to 'unconsolidated' aquifers, there can be much more uncertainty about the direction and rate of contaminant migration and about the processes and factors that control chemical and microbial transformations of contaminants. Research at the NAWC is improving understanding of the transport and fate of chlorinated solvents in fractured-rock aquifers and will compare the effectiveness of different strategies for contaminant remediation.

An Approach Using Gas Monitoring to Find the Residual TCE Location in the Unsaturated Zone of Woosan Industrial Complex (WIC), Korea

NASA Astrophysics Data System (ADS)

Koh, Y.; Lee, S.; Yang, J.; Lee, K.

2012-12-01

An area accommodating various industrial facilities has fairly high probability of groundwater contamination with multiple chlorinated solvents such as trichloroethene (TCE), carbon tetrachloride (CT), and chloroform (CF). Source tracing of chlorinated solvents in the unsaturated zone is an essential procedure for the management and remediation of contaminated area. From the previous study on seasonal variations in hydrological stresses and spatial variations in geologic conditions on a TCE plume, the existence of residual DNAPLs at or above the water table has proved. Since TCE is one of the frequently detected VOCs (Volatile Organic Compounds) in groundwater, residual TCE can be detected by gas monitoring. Therefore, monitoring of temporal and spatial variations in the gas phase TCE contaminant at an industrial complex in Wonju, Korea, were used to find the residual TCE locations. As pilot tests, TCE gas samples collected in the unsaturated zone at 4 different wells were analyzed using SPME (Solid Phase MicroExtraction) fiber and Gas Chromatography (GC). The results indicated that detecting TCE in gas phase was successful from these wells and TCE analysis on gas samples, collected from the unsaturated zone, will be useful for source area characterization. However, some values were too high to doubt the accuracy of the current method, which needs a preliminary lab test with known concentrations. The modified experiment setups using packer at different depths are in process to find residual TCE locations in the unsaturated zone. Meanwhile, several PVD (polyethylene-membrane Passive Vapor Diffusion) samplers were placed under water table to detect VOCs by equilibrium between air in the vial and VOCs in pore water.

Enhancement of In Situ Bioremediation of Energetic Compounds by Coupled Abiotic/Biotic Processes

DTIC Science & Technology

2007-08-01

reduced in the laboratory and successfully treat energetics (RDX, TNT, CL-20, NDMA ), chlorinated solvents (PCE, TCE, TCA, 1,1-DCE, cis-DCE), and...Fruchter, M Williams, V Vermeul, H Fredrickson, and K Thompson. 2006. In situ chemical reduction of sediments for TCE, energetics, and NDMA remediation...sediments for TCE, energetics, and NDMA remediation, Remediation of Chlorinated and Recalcitrant Compounds, Monterey, California, May 2006. Szecsody J

Solvent for the simultaneous recovery of radionuclides from liquid radioactive wastes

DOEpatents

Romanovskiy, Valeriy Nicholiavich; Smirnov, Igor V.; Babain, Vasiliy A.; Todd, Terry A.; Brewer, Ken N.

2002-01-01

The present invention relates to solvents, and methods, for selectively extracting and recovering radionuclides, especially cesium and strontium, rare earths and actinides from liquid radioactive wastes. More specifically, the invention relates to extracting agent solvent compositions comprising complex organoboron compounds, substituted polyethylene glycols, and neutral organophosphorus compounds in a diluent. The preferred solvent comprises a chlorinated cobalt dicarbollide, diphenyl-dibutylmethylenecarbamoylphosphine oxide, PEG-400, and a diluent of phenylpolyfluoroalkyl sulfone. The invention also provides a method of using the invention extracting agents to recover cesium, strontium, rare earths and actinides from liquid radioactive waste.

Method for the simultaneous recovery of radionuclides from liquid radioactive wastes using a solvent

DOEpatents

Romanovskiy, Valeriy Nicholiavich; Smirnov, Igor V.; Babain, Vasiliy A.; Todd, Terry A.; Brewer, Ken N.

2001-01-01

The present invention relates to solvents, and methods, for selectively extracting and recovering radionuclides, especially cesium and strontium, rare earths and actinides from liquid radioactive wastes. More specifically, the invention relates to extracting agent solvent compositions comprising complex organoboron compounds, substituted polyethylene glycols, and neutral organophosphorus compounds in a diluent. The preferred solvent comprises a chlorinated cobalt dicarbollide, diphenyl-dibutylmethylenecarbamoylphosphine oxide, PEG-400, and a diluent of phenylpolyfluoroalkyl sulfone. The invention also provides a method of using the invention extracting agents to recover cesium, strontium, rare earths and actinides from liquid radioactive waste.

BIOREMEDIATION TRAINING

EPA Science Inventory

Bioremediation encompasses a collection of technologies which use microbes to degrade or transform contaminants. Three technologies have an established track record of acceptable performance: aerobic bioventing for fuels; enhanced reductive dechlorination for chlorinated solvent...

JD-2000™

EPA Pesticide Factsheets

Technical product bulletin: this dispersant used in oil spill cleanups is free of phosphates, aromatic chlorinated solvents, branched ethoxylated alcohols, and hydrotreated distillates. Timely application even at low rates can counter mousse forming.

Effect on de-greasing solvents on conductive separable connector shields and semiconductive cable shields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perry, D.D.; Bolcar, J.P.

1990-04-01

A study has been conducted to determine the effects of commercial degreasing solvents on the conductivity of an EPDM separable connector shield and two types of cable shields based on EPR and XLPE, respectively. Solvents tested included a chlorinated solvent based on 1,1,1-trichloroethane and several so-called citrus solvents consisting of the natural terpene, limonene, or blends of limonene with other hydrocarbons. All the solvents significantly degraded the conductivity of the EPR and EPDM materials, but had little effect on the XLPE cable shield. The solvents differed, however, in the extent of their effects, the rate of recovery of conductivity aftermore » removal of the solvent, and the degree to which the original conductivity of the material was restored. The consequences of these results in terms of appropriate field use of these types of solvents by utility personnel are discussed.« less

Post monitoring of a cyclodextrin remeditated chlorinated solvent contaminated aquifer

NASA Astrophysics Data System (ADS)

Blanford, W. J.

2006-12-01

Hydroxypropyl-â-cyclodextrin (HPâCD) has been tested successfully in the laboratory and in the field for enhanced flushing of low-polarity contaminants from aquifers. The cyclodextrin molecule forms a toroidal structure, which has a hydrophobic cavity. Within this cavity, organic compounds of appropriate shape and size can form inclusion complexes, which is the basis for the use of cyclodextrin in groundwater remediation. The hydrophilic exterior of the molecule makes cyclodextrin highly water-soluble. The solubility of cyclodextrins can be further enhanced by adding functional groups, such as hydroxypropyl groups, to the cyclodextrin core. The aqueous solubility of HPâCD exceeds 950 g/L. These high solubilities are advantageous for field applications because they permit relatively high concentrations of the flushing agent. In order for cyclodextrin to become a feasible remediative alternative, it must be demonstrate a short term resistance to biodegradation during field application, but ultimately biodegrade so as not to pose a long term presence in the aquifer. The potential for degradation of cyclodextrin as well as changes in the chlorinated solvents and groundwater geochemistry were examined during the post monitoring of a field demonstration in a shallow aquifer at Little Creek Naval Amphibious Base in Virginia. It was found that a portion of the cyclodextrin remaining in the aquifer after the cessation of field activities biodegraded during the 425 days of post monitoring. This degradation also led to the degradation of the chlorinated solvents trichloroethylene and 1,1-trichloroethane through both biological and chemical processes. The aquifer remained anaerobic with average dissolved oxygen levels below 0.5 mg/L. Dissolved nitrate and sulfate concentrations within the cyclodextrin plume decreased due their being used as terminal electron acceptors during the degradation of the cyclodextrin. The concentrations of total iron at the field site showed no change over time. It can be concluded from this research that cyclodextrin remaining in the subsurface after cessation of active remediation will degrade due to microbial processes. The chlorinated solvents will also degrade through both chemical and biological processes to their daughter products. The terminal electron acceptors present within the cyclodextrin plume will also be used for energy during the degradation processes.

Incorporation of High Energy Materials Into High Density Polymers

DTIC Science & Technology

1987-09-21

and the pure graft copolymer was isolated by selective solvent extraction. 5 f. Isolation of pure Qraft copolymers. The isolation of pure EPDM -g-PS...characterized, such as EPDM -g-PST and EPDM -g-PMST. Two methods of synthesis were successful: a macromonomer (a polymer containing a polymerizab head group) was...copolymerized with ethylene and propylene to lead to the final product, and chlorination of a commercial EPDM allowed the chlorinated sites to serve as

Sol-gel analogous aminolysis-ammonolysis of chlorosilanes to chlorine-free Si/(C)/N-materials.

PubMed

Wiltzsch, Conny; Wagler, Jörg; Roewer, Gerhard; Kroke, Edwin

2009-07-28

Large amounts of chlorosilanes, especially SiCl4 and CH3SiCl3, are produced as side-products of the industrial fabrication of solar or electronic grade silicon and the Müller-Rochow process. It was a goal of the present study to transform these compounds into useful chlorine-free precursors for Si/(C)/N ceramics via a sol-gel analogous liquid processing route. Chlorine substitution of the chlorosilanes (mixtures) with diethylamine did not yield chlorine-free products, complete reactions are only possible with lithium diethylamide. However, aminolyses with n-propylamine were successful. Transamination with ammonia was not possible with diethylaminosilanes but was with n-propylaminosilanes in various solvents. This result was attributed to steric reasons and polar interactions of the N-H groups. Colourless solid or liquid polysilazanes were obtained, depending on the silane (mixture) and the solvent. Transamination reactions of CH3Si(NH-n-Pr)3 in chloroform reproducibly yielded a cage-like oligosilazane of the composition (CH3)9Si9(NH)12N. Single crystal X-ray structure analysis revealed a seven-cyclic cluster containing four six- and three ten-membered silazane rings. This unique silazane cage as well as the other aminosilanes and the silazanes were comprehensively characterised using multi-nuclear solid state and solution NMR, elemental analyses and thermal gravimetry (TGA).

Switchable hydrophilicity solvents for lipid extraction from microalgae for biofuel production.

PubMed

Boyd, Alaina R; Champagne, Pascale; McGinn, Patrick J; MacDougall, Karen M; Melanson, Jeremy E; Jessop, Philip G

2012-08-01

A switchable hydrophilicity solvent (SHS) was studied for its effectiveness at extracting lipids from freeze-dried samples of Botryococcus braunii microalgae. The SHS N,N-dimethylcyclohexylamine extracted up to 22 wt.% crude lipid relative to the freeze-dried cell weight. The solvent was removed from the extract with water saturated with carbon dioxide at atmospheric pressure and recovered from the water upon de-carbonation of the mixture. Liquid chromatography-mass spectrometry (LC-MS) showed that the extracted lipids contained high concentrations of long chain tri-, di- and mono-acylglycerols, no phospholipids, and only 4-8% of residual solvent. Unlike extractions with conventional organic solvents, this new method requires neither distillation nor the use of volatile, flammable or chlorinated organic solvents. Copyright © 2012 Elsevier Ltd. All rights reserved.

Remediation of Chlorinated Solvent Plumes Using In-Situ Air Sparging—A 2-D Laboratory Study

PubMed Central

Adams, Jeffrey A.; Reddy, Krishna R.; Tekola, Lue

2011-01-01

In-situ air sparging has evolved as an innovative technique for soil and groundwater remediation impacted with volatile organic compounds (VOCs), including chlorinated solvents. These may exist as non-aqueous phase liquid (NAPL) or dissolved in groundwater. This study assessed: (1) how air injection rate affects the mass removal of dissolved phase contamination, (2) the effect of induced groundwater flow on mass removal and air distribution during air injection, and (3) the effect of initial contaminant concentration on mass removal. Dissolved-phase chlorinated solvents can be effectively removed through the use of air sparging; however, rapid initial rates of contaminant removal are followed by a protracted period of lower removal rates, or a tailing effect. As the air flow rate increases, the rate of contaminant removal also increases, especially during the initial stages of air injection. Increased air injection rates will increase the density of air channel formation, resulting in a larger interfacial mass transfer area through which the dissolved contaminant can partition into the vapor phase. In cases of groundwater flow, increased rates of air injection lessened observed downward contaminant migration effect. The air channel network and increased air saturation reduced relative hydraulic conductivity, resulting in reduced groundwater flow and subsequent downgradient contaminant migration. Finally, when a higher initial TCE concentration was present, a slightly higher mass removal rate was observed due to higher volatilization-induced concentration gradients and subsequent diffusive flux. Once concentrations are reduced, a similar tailing effect occurs. PMID:21776228

Remediation of chlorinated solvent plumes using in-situ air sparging--a 2-D laboratory study.

PubMed

Adams, Jeffrey A; Reddy, Krishna R; Tekola, Lue

2011-06-01

In-situ air sparging has evolved as an innovative technique for soil and groundwater remediation impacted with volatile organic compounds (VOCs), including chlorinated solvents. These may exist as non-aqueous phase liquid (NAPL) or dissolved in groundwater. This study assessed: (1) how air injection rate affects the mass removal of dissolved phase contamination, (2) the effect of induced groundwater flow on mass removal and air distribution during air injection, and (3) the effect of initial contaminant concentration on mass removal. Dissolved-phase chlorinated solvents can be effectively removed through the use of air sparging; however, rapid initial rates of contaminant removal are followed by a protracted period of lower removal rates, or a tailing effect. As the air flow rate increases, the rate of contaminant removal also increases, especially during the initial stages of air injection. Increased air injection rates will increase the density of air channel formation, resulting in a larger interfacial mass transfer area through which the dissolved contaminant can partition into the vapor phase. In cases of groundwater flow, increased rates of air injection lessened observed downward contaminant migration effect. The air channel network and increased air saturation reduced relative hydraulic conductivity, resulting in reduced groundwater flow and subsequent downgradient contaminant migration. Finally, when a higher initial TCE concentration was present, a slightly higher mass removal rate was observed due to higher volatilization-induced concentration gradients and subsequent diffusive flux. Once concentrations are reduced, a similar tailing effect occurs.

Mixed Redox Catalytic Destruction of Chlorinated Solvents in Soils and Groundwater: From the Laboratory to the Field

PubMed Central

Gao, Song; Rupp, Erik; Bell, Suzanne; Willinger, Martin; Foley, Theresa; Barbaris, Brian; Sáez, A. Eduardo; Arnold, Robert G.; Betterton, Eric

2010-01-01

A new thermocatalytic method to destroy chlorinated solvents has been developed in the laboratory and tested in a pilot field study. The method employs a conventional Pt/Rh catalyst on a ceramic honeycomb. Reactions proceed at moderate temperatures in the simultaneous presence of oxygen and a reductant (mixed redox conditions) to minimize catalyst deactivation. In the laboratory, stable operation with high conversions (above 90% at residence times shorter than 1 s) for perchloroethylene (PCE) is achieved using hydrogen as the reductant. A molar ratio of H2/O2 = 2 yields maximum conversions; the temperature required to produce maximum conversions is sensitive to influent PCE concentration. When a homologous series of aliphatic alkanes is used to replace hydrogen as the reductant, the resultant mixed redox conditions also produce high PCE conversions. It appears that the dissociation energy of the C–H bond in the respective alkane molecule is a strong determinant of the activation energy, and therefore the reaction rate, for PCE conversion. This new method was employed in a pilot field study in Tucson, Arizona. The mixed redox system was operated semicontinuously for 240 days with no degradation of catalyst performance and complete destruction of PCE and trichloroethylene in a soil vapor extraction gas stream. Use of propane as the reductant significantly reduced operating costs. Mixed redox destruction of chlorinated solvents provides a potentially viable alternative to current soil and groundwater remediation technologies. PMID:18991945

Compatibility of Halthane 88-3 urethane adhesive with the replacement cleaning solvent D-Limonene

DOE Office of Scientific and Technical Information (OSTI.GOV)

LeMay, J.D.; Mendoza, B.

1991-08-01

D-Limonene, (R)1-methyl-4-isopropenyl-1-cyclohexene, has been identified as a leading replacement for chlorinated solvents traditionally used to clean electrical assemblies and critical components in some phases of weapons production. Unfortunately, d-limonene has a much lower vapor pressure than the chlorinated solvents if replaces (<2 torr at ambient). This makes its complete elimination from cleaned subassemblies potentially difficult, and gives rise to concerns about the compatibility of d-limonene with materials in the warhead. During the past year many WR polymers and adhesives have been surveyed for their compatibility with d-limonene. Preliminary test results obtained at Sandia (Albuquerque) and Allied-Signal (KCD) showed that Aluminum/Halthanemore » 88-3/Aluminum joints were destroyed during exposure to saturated d-limonene vapor. The cause of bond failure appeared to be d-limonene induced swelling of the Halthane polymer. This report describes recent work performed at LLNL to study the swelling behavior and bond strength degradation of Halthane 88-3 resulting from exposure to d-limonene vapor.« less

Household Effectiveness vs. Laboratory Efficacy of Point-of-use Chlorination

PubMed Central

Levy, Karen; Anderson, Larissa; Robb, Katharine A.; Cevallos, William; Trueba, Gabriel; Eisenberg, Joseph N.S.

2014-01-01

Treatment of water at the household level offers a promising approach to combat the global burden of diarrheal diseases. In particular, chlorination of drinking water has been a widely promoted strategy due to persistence of residual chlorine after initial treatment. However, the degree to which chlorination can reduce microbial levels in a controlled setting (efficacy) or in a household setting (effectiveness) can vary as a function of chlorine characteristics, source water characteristics, and household conditions. To gain more understanding of these factors, we carried out an observational study within households in rural communities of northern coastal Ecuador. We found that the efficacy of chlorine treatment under controlled conditions was significantly better than its effectiveness when evaluated both by ability to meet microbiological safety standards and by log reductions. Water treated with chlorine achieved levels of microbial contamination considered safe for human consumption after 24 hours of storage in the household only 39 – 51% of the time, depending on chlorine treatment regimen. Chlorine treatment would not be considered protective against diarrheal disease according to WHO log reduction standards. Factors that explain the observed compromised effectiveness include: source water turbidity, source water baseline contamination levels, and in-home contamination. Water in 38% of the households that had low turbidity source water (< 10 NTU) met the safe water standard as compared with only 17% of the households that had high turbidity source water (> 10 NTU). A 10 MPN/100mL increase in baseline E. coli levels was associated with a 2.2% increase in failure to meet the E. colistandard. Higher mean microbial contamination levels in 54% of household samples in comparison to their matched controls, which is likely the result of in-home contamination during storage. Container characteristics (size of the container mouth) did not influence chlorine effectiveness. We found no significant differences between chlorine treatment regimens in ability to meet the safe water standards or in overall log reductions, although chlorine dosage did modify the effect of source conditions. These results underscore the importance of measuring both source water and household conditions to determine appropriate chlorine levels, as well as to evaluate the appropriateness of chlorine treatment and other point-of-use water quality improvement interventions. PMID:24561887

Household effectiveness vs. laboratory efficacy of point-of-use chlorination.

PubMed

Levy, Karen; Anderson, Larissa; Robb, Katharine A; Cevallos, William; Trueba, Gabriel; Eisenberg, Joseph N S

2014-05-01

Treatment of water at the household level offers a promising approach to combat the global burden of diarrheal diseases. In particular, chlorination of drinking water has been a widely promoted strategy due to persistence of residual chlorine after initial treatment. However, the degree to which chlorination can reduce microbial levels in a controlled setting (efficacy) or in a household setting (effectiveness) can vary as a function of chlorine characteristics, source water characteristics, and household conditions. To gain more understanding of these factors, we carried out an observational study within households in rural communities of northern coastal Ecuador. We found that the efficacy of chlorine treatment under controlled conditions was significantly better than its household effectiveness when evaluated both by ability to meet microbiological safety standards and by log reductions. Water treated with chlorine achieved levels of microbial contamination considered safe for human consumption after 24 h of storage in the household only 39-51% of the time, depending on chlorine treatment regimen. Chlorine treatment would not be considered protective against diarrheal disease according to WHO log reduction standards. Factors that explain the observed compromised effectiveness include: source water turbidity, source water baseline contamination levels, and in-home contamination. Water in 38% of the households that had low turbidity source water (<10 NTU) met the safe water standard as compared with only 17% of the households that had high turbidity source water (>10 NTU). A 10 MPN/100 mL increase in baseline Escherichia coli levels was associated with a 2.2% increase in failure to meet the E. coli standard. Higher mean microbial contamination levels were seen in 54% of household samples in comparison to their matched controls, which is likely the result of in-home contamination during storage. Container characteristics (size of the container mouth) did not influence chlorine effectiveness. We found no significant differences between chlorine treatment regimens in ability to meet the safe water standards or in overall log reductions, although chlorine dosage did modify the effect of source conditions. These results underscore the importance of measuring both source water and household conditions to determine appropriate chlorine levels, as well as to evaluate the appropriateness of chlorine treatment and other point-of-use water quality improvement interventions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Solid state synthesis of poly(dichlorophosphazene)

DOEpatents

Allen, Christopher W.; Hneihen, Azzam S.; Peterson, Eric S.

2001-01-01

A method for making poly(dichlorophosphazene) using solid state reactants is disclosed and described. The present invention improves upon previous methods by removing the need for chlorinated hydrocarbon solvents, eliminating complicated equipment and simplifying the overall process by providing a "single pot" two step reaction sequence. This may be accomplished by the condensation reaction of raw materials in the melt phase of the reactants and in the absence of an environmentally damaging solvent.

Synthesis and properties of new chlorin and bacteriochlorin photosensitizers

NASA Astrophysics Data System (ADS)

Mironov, Andrei F.

1996-01-01

A series of novel sensitizers, which absorb in the range of 660 - 820 nm, derived from natural occurring chlorophyll and bacteriochlorophyll was synthesized. Biomass of blue-green algae Spirulina platensis was used to prepare chlorophyll a derivatives, and biomass of purple bacteria Rhodobacter capsulatus was applied for preparation of bacteriochlorophyll a. The influence of different substituents on spectral characteristics and the amphipility of the sensitizer was investigated. The route for the synthesis of porphyrin macrocycle with the spacer that bears the isothiocyanate group capable for binding with proteins was proposed. Photophysical properties of chlorin p6, purpurin 18 and their esters in different solvents are investigated. Accumulation of two chlorins in the model Erlich tumor was studied.

Risk of liver cancer and exposure to organic solvents and gasoline vapors among Finnish workers.

PubMed

Lindbohm, Marja-Liisa; Sallmén, Markku; Kyyrönen, Pentti; Kauppinen, Timo; Pukkala, Eero

2009-06-15

We investigated the association between exposure to various groups of solvents and gasoline vapors and liver cancer. A cohort of economically active Finns born between 1906 and 1945 was followed up during the period 1971-1995. The incident cases of primary liver cancer (n = 2474) were identified in a record linkage with the Finnish Cancer Registry. Occupations from the 1970 census were converted to exposures using a job-exposure matrix. Cumulative exposure was calculated as the product of estimated prevalence, level and duration of exposure, and we used Poisson regression to calculate the relative risks (RR). Among the occupations entailing exposure to organic solvents, an elevated liver cancer incidence was observed in male printers, and varnishers and lacquerers. Among men, the risk was increased in the highest exposure category of aromatic hydrocarbons [RR 1.77, 95% confidence interval (CI) 1.30-2.40], aliphatic/alicyclic hydrocarbons (RR 1.47, 95% CI 0.99-2.18), chlorinated hydrocarbons (RR 2.65, 95% CI 1.38-5.11) and "other solvents" (RR 2.14, 95% CI 1.23-3.71). Among women, the risk was increased for the group "other solvents" that includes mainly alcohols, ketones, esters and glycol ethers (RR 2.73, 95% CI 1.21-6.16). Our finding of an increased risk among workers exposed to chlorinated hydrocarbons is in line with several earlier studies on trichloroethylene. The results also suggest a link between exposure to other types of solvents and the risk of liver cancer. The possibility that alcohol consumption contributes to the observed risks cannot be totally excluded. Copyright 2008 UICC.

Transport, Targeting, and Applications of Metallic Functional Nanoparticles for Degradation of DNAPL Chlorinated Organic Solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gregory V. Lowry; Sara Majetich; Krzysztof Matyjaszewski

2006-12-27

Dense Non-Aqueous Phase Liquid (DNAPL) such as trichloroethylene act as long term sources of groundwater contaminants and are difficult and expensive to remediate. DNAPL-contaminated sites are a significant financial liability for the Department of Energy and the private sector. The objective of this study was to engineer reactive Fe-based nanoparticles with specialized polymeric coatings to make them mobile in the subsurface and to provide them with an affinity for the DNAPL/water interface. The synthesis, characterization, and reactivity/mobility of the engineered particles, and a molecular dynamic model that predicts their behavior at the DNPAL/water interface are described in this report.

DNAPL SITE EVALUATION - Project Summary

EPA Science Inventory

Dense nonaqueous-phase liquids (DNAPLs), especially chlorinated solvents, are among the most prevalent subsurface contaminants identified in ground-water supplies and at waste disposal sites. There are several site-characterization issues specific to DNAPL sites including (a) the...

Alternate methods of asphalt content determination.

DOT National Transportation Integrated Search

1996-01-01

This study identified an alternate method of asphalt content determination to replace chlorinated solvent extraction. The production of trichloroethane was outlawed on December 31, 1996 as part of the 1990 Clean Air Act Amendments. Initially, the stu...

29 CFR 1915.51 - Ventilation and protection in welding, cutting and heating.

Code of Federal Regulations, 2010 CFR

2010-07-01

... from the exposed arc, and surfaces prepared with chlorinated solvents shall be thoroughly dry before... heating shall be protected by suitable eye protective equipment in accordance with the requirements of...

METHODS AND ANALYSES FOR IMPLEMENTING NATURAL ATTENUATION PROTOCOLS

EPA Science Inventory

Technical protocols for evaluating natural attenuation at petroleum hydrocarbon and chlorinated solvent contaminated sites specify the analysis of electron acceptors and metabolic by-products for identifying and quantifying natural attenuation processes. However, these protocols ...

Modeling 3D-CSIA data: Carbon, chlorine, and hydrogen isotope fractionation during reductive dechlorination of TCE to ethene.

PubMed

Van Breukelen, Boris M; Thouement, Héloïse A A; Stack, Philip E; Vanderford, Mindy; Philp, Paul; Kuder, Tomasz

2017-09-01

Reactive transport modeling of multi-element, compound-specific isotope analysis (CSIA) data has great potential to quantify sequential microbial reductive dechlorination (SRD) and alternative pathways such as oxidation, in support of remediation of chlorinated solvents in groundwater. As a key step towards this goal, a model was developed that simulates simultaneous carbon, chlorine, and hydrogen isotope fractionation during SRD of trichloroethene, via cis-1,2-dichloroethene (and trans-DCE as minor pathway), and vinyl chloride to ethene, following Monod kinetics. A simple correction term for individual isotope/isotopologue rates avoided multi-element isotopologue modeling. The model was successfully validated with data from a mixed culture Dehalococcoides microcosm. Simulation of Cl-CSIA required incorporation of secondary kinetic isotope effects (SKIEs). Assuming a limited degree of intramolecular heterogeneity of δ 37 Cl in TCE decreased the magnitudes of SKIEs required at the non-reacting Cl positions, without compromising the goodness of model fit, whereas a good fit of a model involving intramolecular CCl bond competition required an unlikely degree of intramolecular heterogeneity. Simulation of H-CSIA required SKIEs in H atoms originally present in the reacting compounds, especially for TCE, together with imprints of strongly depleted δ 2 H during protonation in the products. Scenario modeling illustrates the potential of H-CSIA for source apportionment. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Origin of VC-only plumes from naturally enhanced dechlorination in a peat-rich hydrogeologic setting

NASA Astrophysics Data System (ADS)

Filippini, Maria; Amorosi, Alessandro; Campo, Bruno; Herrero-Martìn, Sara; Nijenhuis, Ivonne; Parker, Beth L.; Gargini, Alessandro

2016-09-01

The occurrence of vinyl chloride (VC) is often a main concern at sites contaminated with chlorinated solvents due to its high degree of toxicity and carcinogenicity. VC occurrence in aquifers is most often related to the degradation of higher chlorinated ethenes or ethanes and it is generally detected in plumes along with parent contaminants. However, specific combination of stratigraphic, hydrogeologic and geochemical conditions can enhance the degradation of parents and lead to the formation of plumes almost entirely composed of VC (i.e. VC-only plumes). This paper investigates the causes of VC-only plumes in the aquifers below the city of Ferrara (northern Italy) by combining multiple lines of evidence. The City of Ferrara is located on an alluvial lowland, built by the River Po, and is made up of alternating unconsolidated sandy aquifer and silt-clay aquitard deposits of fluvial origin. This region has been strongly impacted by prior industrial activities, with the occurrence of chlorinated compounds at several sites. VC-only plumes with uncertain source location were found at two contaminated sites. The source zone of a third plume composed of chloroethenes from PCE to VC was investigated for high resolution depositional facies architecture and contaminant distribution (contaminant concentration and Compound Specific Isotope Analysis - CSIA). The investigation suggested that degradation of PCE and TCE takes place during contaminant migration through peat-rich (swamp) layers related to the Holocene transgression, which locally act as a ;reactor; for stimulating degradation with the accumulation of VC in the strongly reducing environment of the peat. Regional-scale stratigraphic architecture showed the ubiquitous occurrence of swamp layers at distinct stratigraphic levels in the investigated system and their apparent linkage to the in situ creation of the VC-only plumes.

Atopic Dermatitis

MedlinePlus

... perfumes and cosmetics. Substances such as chlorine, mineral oil, or solvents. Dust or sand. Cigarette smoke. Sleep problems. Foods that seem to be related to skin flares. Previous treatments for skin-related symptoms. Use of steroids or other medications. Identify factors that ...

29 CFR 1926.353 - Ventilation and protection in welding, cutting, and heating.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., and surfaces prepared with chlorinated solvents shall be thoroughly dry before welding is permitted on... suitable eye protective equipment in accordance with the requirements of subpart E of this part. [44 FR...

EVALUATION OF PERMEABLE REACTIVE BARRIER PERFORMANCE

EPA Science Inventory

The permeable reactive barrier (PRB) technology represents a passive option for long-term treatment of ground-water contamination. PRBs are a potentially more cost-effective treatment option for a variety of dissolved contaminants, such as certain types of chlorinated solvents, ...

ELECTROCHEMICAL DEGRADATION OF PERSISTANCE POLLUTANTS IN GROUNDWATER AND SEDIMENTS

EPA Science Inventory

Electrochemical Degradation (ECD) utilizes redox potential at the anode and the cathode to oxidize and/or reduce organic contaminants. ECD of environmentally persistence pollutants such chlorinate solvents, PCBs, and PAHs, although theoretically possible, has not been experimenta...

MASS BALANCE ANALYSIS FOR MICROBIAL DECHLORINATION OF TETRACHLOROETHENE

EPA Science Inventory

Contamination of subsurface environments by chlorinated aliphatic solvents and petroleum hydrocarbons is a significant public health concern because groundwater is one of the major drinking water resources in the United States. Biotic and abiotic techniques have been widely exam...

Constraining wintertime sources of inorganic chlorine over the northeast United States

NASA Astrophysics Data System (ADS)

Haskins, J.; Jaegle, L.; Shah, V.; Lopez-Hilfiker, F.; Lee, B. H.; Campuzano Jost, P.; Schroder, J. C.; Day, D. A.; Fiddler, M. N.; Holloway, J. S.; Sullivan, A.; Veres, P. R.; Weber, R. J.; Dibb, J. E.; Brown, S. S.; Jimenez, J. L.; Thornton, J. A.

2017-12-01

Wintertime multiphase chlorine chemistry is thought to play a significant role in the regional distribution of oxidants, the lifetime of VOCs, and the transport of NOx downwind of urban sources. However, the sources and chemistry of reactive chlorine remain highly uncertain. During the WINTER 2015 aircraft campaign, the inorganic chlorine budget was dominated by HCl (g) and total particulate chloride, accounting for greater than 85% of the total chlorine budget within the boundary layer. The total concentration of inorganic chlorine compounds found over marine regions was 1014 pptv and 609 pptv over continental regions with variability found to be driven by changes in meteorological conditions, particle liquid water content, particle pH, and proximity to large anthropogenic sources. However, displacement of particle chloride was often not a large enough source to fully explain the concentrations of gas phase Cly compounds. We use the GEOS-Chem global chemical transport model to simulate the emissions, gas-particle partitioning, and downwind transport and deposition of Cly during winter. Simulated concentrations of HCl, particle chloride, and other dominant Cly compounds are compared to measurements made during the WINTER aircraft campaign. The relative roles of Cly sources from sea-salt aerosol and anthropogenic sources such as power plants, biomass burning and road salt are explored.

Annual Report to Congress - Fiscal Year 1996. A Report by the Council of the Strategic Environmental Research and Development Program

DTIC Science & Technology

1997-03-01

volatile organic compounds (VOCs), dense non-aqueous phase liquids (DNAPLs), and permeable reactive walls for chlorinated solvents The GRFL is the only... compounds , solvents, and heavy metals. SCAPS technology has been demonstrated to reduce the costs of traditional site screening by up to 90 percent; it...styphnate and volatile organic compounds (VOCs). Hazardous wastes also are generated during demilitarization. Under partial sponsorship of SERDP, the US Army

Reducing chlorinated solvent emissions from three vapor degreasers: 1990 summer intern project conducted at Alliant Techsystems, Inc., New Brighton, Minnesota

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hymes, C.

1990-12-31

Alliant Techsystems manufactures aluminum and steel components for armaments, under defense contract, at building 502 in Arden Hills, MN. As part of the manufacturing process, six vapor degreasers are used to remove oil and other soils from the components. The focus of this study was to identify the causes of solvent loss from three of the degreasers, and suggest options for reducing those losses.

Chemically enhanced in situ recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sale, T.; Pitts, M.; Wyatt, K.

1996-08-01

Chemically enhanced recovery is a promising alternative to current technologies for management of subsurface releases of organic liquids. Through the inclusion of surfactants, solvents, polymers, and/or alkaline agents to a waterflood, the transport of targeted organic compounds can be increased and rates of recovery enhanced. By far, the vast majority of work done in the field of chemically enhanced recovery has been at a laboratory scale. The following text focuses on chemically enhanced recovery from a field application perspective with emphasis given to chlorinated solvents in a low permeability setting. While chlorinated solvents are emphasized, issues discussed are also relevantmore » to organic liquids less dense than water such as petroleum products. Topics reviewed include: (1) Description of technology; (2) General technology considerations; (3) Low permeability media considerations; (4) Cost and reliability considerations; (5) Commercial availability; and (6) Case histories. Through this paper an appreciation is developed of both the potential and limitations of chemically enhanced recovery. Excluded from the scope of this paper is the in situ destruction of organic compounds through processes such as chemical or biological oxidation, chemically enhanced recovery of inorganic compounds, and ex situ soil treatment processes. 11 refs., 2 figs., 1 tab.« less

Phytoscreening with SPME: Variability Analysis.

PubMed

Limmer, Matt A; Burken, Joel G

2015-01-01

Phytoscreening has been demonstrated at a variety of sites over the past 15 years as a low-impact, sustainable tool in delineation of shallow groundwater contaminated with chlorinated solvents. Collection of tree cores is rapid and straightforward, but low concentrations in tree tissues requires sensitive analytics. Solid-phase microextraction (SPME) is amenable to the complex matrix while allowing for solvent-less extraction. Accurate quantification requires the absence of competitive sorption, examined here both in laboratory experiments and through comprehensive examination of field data. Analysis of approximately 2,000 trees at numerous field sites also allowed testing of the tree genus and diameter effects on measured tree contaminant concentrations. Collectively, while these variables were found to significantly affect site-adjusted perchloroethylene (PCE) concentrations, the explanatory power of these effects was small (adjusted R(2) = 0.031). 90th quantile chemical concentrations in trees were significantly reduced by increasing Henry's constant and increasing hydrophobicity. Analysis of replicate tree core data showed no correlation between replicate relative standard deviation (RSD) and wood type or tree diameter, with an overall median RSD of 30%. Collectively, these findings indicate SPME is an appropriate technique for sampling and analyzing chlorinated solvents in wood and that phytoscreening is robust against changes in tree type and diameter.

Tolerance of anaerobic bacteria to chlorinated solvents.

PubMed

Koenig, Joanna C; Groissmeier, Kathrin D; Manefield, Mike J

2014-01-01

The aim of this research was to evaluate the effects of four chlorinated aliphatic hydrocarbons (CAHs), perchloroethene (PCE), carbon tetrachloride (CT), chloroform (CF) and 1,2-dichloroethane (1,2-DCA), on the growth of eight anaerobic bacteria: four fermentative species (Escherichia coli, Klebsiella sp., Clostridium sp. and Paenibacillus sp.) and four respiring species (Pseudomonas aeruginosa, Geobacter sulfurreducens, Shewanella oneidensis and Desulfovibrio vulgaris). Effective concentrations of solvents which inhibited growth rates by 50% (EC50) were determined. The octanol-water partition coefficient or log Po/w of a CAH proved a generally satisfactory measure of its toxicity. Most species tolerated approximately 3-fold and 10-fold higher concentrations of the two relatively more polar CAHs CF and 1,2-DCA, respectively, than the two relatively less polar compounds PCE and CT. EC50 values correlated well with growth rates observed in solvent-free cultures, with fast-growing organisms displaying higher tolerance levels. Overall, fermentative bacteria were more tolerant to CAHs than respiring species, with iron- and sulfate-reducing bacteria in particular appearing highly sensitive to CAHs. These data extend the current understanding of the impact of CAHs on a range of anaerobic bacteria, which will benefit the field of bioremediation.

Tolerance of Anaerobic Bacteria to Chlorinated Solvents

PubMed Central

Koenig, Joanna C.; Groissmeier, Kathrin D.; Manefield, Mike J.

2014-01-01

The aim of this research was to evaluate the effects of four chlorinated aliphatic hydrocarbons (CAHs), perchloroethene (PCE), carbon tetrachloride (CT), chloroform (CF) and 1,2-dichloroethane (1,2-DCA), on the growth of eight anaerobic bacteria: four fermentative species (Escherichia coli, Klebsiella sp., Clostridium sp. and Paenibacillus sp.) and four respiring species (Pseudomonas aeruginosa, Geobacter sulfurreducens, Shewanella oneidensis and Desulfovibrio vulgaris). Effective concentrations of solvents which inhibited growth rates by 50% (EC50) were determined. The octanol-water partition coefficient or log Po/w of a CAH proved a generally satisfactory measure of its toxicity. Most species tolerated approximately 3-fold and 10-fold higher concentrations of the two relatively more polar CAHs CF and 1,2-DCA, respectively, than the two relatively less polar compounds PCE and CT. EC50 values correlated well with growth rates observed in solvent-free cultures, with fast-growing organisms displaying higher tolerance levels. Overall, fermentative bacteria were more tolerant to CAHs than respiring species, with iron- and sulfate-reducing bacteria in particular appearing highly sensitive to CAHs. These data extend the current understanding of the impact of CAHs on a range of anaerobic bacteria, which will benefit the field of bioremediation. PMID:24441515

Transgenic plants and associated bacteria for phytoremediation of chlorinated compounds.

PubMed

Van Aken, Benoit; Doty, Sharon Lafferty

2010-01-01

Phytoremediation is the use of plants for the treatment of environmental pollution, including chlorinated organics. Although conceptually very attractive, removal and biodegradation of chlorinated pollutants by plants is a rather slow and inefficient process resulting in incomplete treatment and potential release of toxic metabolites into the environment. In order to overcome inherent limitations of plant metabolic capabilities, plants have been genetically modified, following a strategy similar to the development of transgenic crops: genes from bacteria, fungi, and mammals involved in the metabolism of organic contaminants, such as cytochrome P-450 and glutathione S-transferase, have been introduced into higher plants, resulting in significant improvement of tolerance, removal, and degradation of pollutants. Recently, plant-associated bacteria have been recognized playing a significant role in phytoremediation, leading to the development of genetically modified rhizospheric and endophytic bacteria with improved biodegradation capabilities. Transgenic plants and associated bacteria constitute a new generation of genetically modified organisms for efficient and environmental-friendly treatment of polluted soil and water. This review focuses on recent advances in the development of transgenic plants and bacteria for the treatment of chlorinated pollutants, including chlorinated solvents, polychlorinated phenols, and chlorinated herbicides.

PHYTOREMEDIATION: AN ECOLOGICAL SOLUTION TO ORGANIC CHEMICAL CONTAMINATION

EPA Science Inventory

Phytoremediation is a promising new technology that uses plants to degrade, assimilate, metabolize, or detoxify metals, hydrocarbons, pesticides, and chlorinated solvents. In this review, in situ, in vivo and in vitro methods of application are described for remediation of these ...

Applications of Monitored Natural Attenuation in the USA (Abstract)

EPA Science Inventory

Monitored Natural Attenuation (MNA) is widely applied in the USA to control the risk associated with ground water contamination from chlorinated solvents such a tetrachloroethylene (PCE) and trichloroethylene (TCE). MNA relies on the natural processes of degradation, sorption an...

Applications of Monitored Natural Attenuation in the USA (Presentation)

EPA Science Inventory

Monitored Natural Attenuation (MNA) is widely applied in the USA to control the risk associated with ground water contamination from chlorinated solvents such a tetrachloroethylene (PCE) and trichloroethylene (TCE). MNA relies on the natural processes of degradation, sorption an...

MULTIDISCIPLINARY APPROACH TO TOXICOLOGICAL SCREENING: II. DEVELOPMENTAL TOXICITY

EPA Science Inventory

As part of the validation of an integrated bioassay for systemic, neuro-, and developmental toxicity, we evaluated the responses of Fischer-344 rats to four pesticides, four chlorinated solvents, and two other industrial chemicals. he pesticides included carbaryl, triadimefon, ch...

IN-SITU OXIDATION OF 1,4-DIOXANE (LABORATORY RESULTS)

EPA Science Inventory

Interest in the solvent stabilizer, 1,4-dioxane, is increasing because analytical detection limits have decreased indicating its presence at chlorinated volatile organic compound contaminated sites. The most common method for removing 1,4-dioxane from contaminated water is advanc...

Spectral Induced Polarization Response of Unconsolidated Saturated Sand and Surfactant Solutions

EPA Science Inventory

Dense non-aqueous phase liquids (DNAPL), such as chlorinated solvents, are common groundwater contaminants. Traditional pump-and-treat methods are often not effective at removing residual DNAPL from the subsurface. Surfactant-enhanced aquifer remediation is a promising remediatio...

MICROBIAL CHARACTERIZATION OF MANURE BASED PERMEABLE REACTIVE BARRIER

EPA Science Inventory

The implementation of permeable reactive barriers (PRB) provides a viable option for the remediation of contaminants of environmental significance such as dissolved metals (i.e., chromium), chlorinated solvents, and nitrate/ammonia. The designs of PRBs are usually based on the a...

PROPERTIES OF FOOD GRADE (EDIBLE) SURFACTANTS AFFECTING SUBSURFACE REMEDIATION OF CHLORINATED SOLVENTS

EPA Science Inventory

In this research, several food grade (edible) surfactants are systematically evaluated for various loss mechanisms: precipitation, adsorption, and coacervation (for nonionic surfactants). Cloud points for the polyethoxylate sorbitan (T-MAZ) surfactants are much higher than aquife...

DETERMINATION OF PESTICIDES AND PCB'S IN INDUSTRIAL AND MUNICIPAL WASTEWATERS

EPA Science Inventory

Steps in the procedure for the analysis of 25 chlorinated pesticides and polychlorinated biphenyls were studied. Two gas chromatographic columns and two detectors (electron capture and Hall electrolytic conductivity) were evaluated. Extractions were performed with two solvents (d...

Prospects for harnessing biocide resistance for bioremediation and detoxification.

PubMed

Atashgahi, Siavash; Sánchez-Andrea, Irene; Heipieper, Hermann J; van der Meer, Jan R; Stams, Alfons J M; Smidt, Hauke

2018-05-18

Prokaryotes in natural environments respond rapidly to high concentrations of chemicals and physical stresses. Exposure to anthropogenic toxic substances-such as oil, chlorinated solvents, or antibiotics-favors the evolution of resistant phenotypes, some of which can use contaminants as an exclusive carbon source or as electron donors and acceptors. Microorganisms similarly adapt to extreme pH, metal, or osmotic stress. The metabolic plasticity of prokaryotes can thus be harnessed for bioremediation and can be exploited in a variety of ways, ranging from stimulated natural attenuation to bioaugmentation and from wastewater treatment to habitat restoration. Copyright © 2018 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

A survey of the geophysical properties of chlorinated DNAPLs

NASA Astrophysics Data System (ADS)

Ajo-Franklin, Jonathan B.; Geller, Jil T.; Harris, Jerry M.

2006-07-01

Dense Non Aqueous Phase Liquids (DNAPLs) are a family of fluids often encountered as industrial contaminants. Some of the most problematic DNAPLs are chlorinated solvents such as trichloroethylene (TCE) and tetrachloroethylene (PCE). While many DNAPLs have been extensively studied from a hydrology perspective, documentation of DNAPL properties relevant to geophysical detection is far from complete. We present a short survey of acoustic velocity, density, and dielectric constant measurements for an important subset of commonly encountered dense chlorinated contaminants. Viscosity and surface tension data are included to allow exploration of contaminant signatures within the context of poroelastic or contact theory models. Where available, the temperature dependence of solvent properties are also provided. Densities for the listed DNAPLs range from 1253 to 1622 kg/m 3 at 20 °C. All are effectively non-polar with dielectric constants between 2.2 and 10.9 and have relatively low compressional wave velocities ranging from 938 to 1217 m/s. We conclude with documentation of a small collection of recent experiments investigating the properties of soils partially saturated with similar fluids. Current laboratory evidence demonstrates that DNAPLs can produce changes in geophysically measurable properties. We hope that this survey will facilitate further studies of the feasibility and effectiveness of geophysical techniques for detection of DNAPLs in the subsurface.

Study on Sources of Volatile Organic Compounds (CMB) in Pearl River Delta region, China

NASA Astrophysics Data System (ADS)

Liu, Y.; Shao, M.; Lu, S.; Chang, C.; Wang, C. J.; Wang, B.

2007-05-01

The profiles of major Volatile organic compounds (VOCs) sources including vehicle exhaust, gasoline vapor, painting, asphalt, liquefied petroleum gas (LPG), biomass burning and petrochemical industry in Pearl River Delta were experimentally determined. Source samples were taken by using dilution chamber for mobile and stationary sources, laboratory simulation for biomass burning. The concentrations of 108 VOC species of sources were quantified by using canister with pre-concentration-GC/MS system, from which 52 PAMS hydrocarbons and one kind of chlorinated hydrocarbon were deployed to build the source profiles for source apportionment of VOCs. Based the measurement of source profiles, the possible tracers for various emission sources were identified, e.g 2-methylbutane and 1,3-butadiene were the tracers for motor vehicle exhaust, the characteristic compounds of architectural and furnishing coatings are aromatics such as toluene and m/p-xylene; the light hydrocarbons, namely n-butane, trans-2-butene and n-pentane, dominated the composition of gasoline vapor; and the nonane, decane and undecane are found to represent the asphalt emissions etc.. The CMB receptor model was applied to source apportionment of 58 hydrocarbons measured at seven sites during the PRD campaign, 2004. The 12 kinds of VOC sources include gasoline/diesel-powered vehicle exhaust, gasoline/diesel headspace vapor, vehicle evaporative emissions, liquid petroleum gas (LPG) leakage, painting vapors, asphalt emission from paved road, biomass burning, coal burning, chemical industry and petroleum refinery. Vehicle exhaust was the largest sources contributing over half of the ambient VOCs at the three urban sites (GuangZhou, FoShan and ZhongShan). LPG leakage played an important role with the percentage of 8- 16% in most sites in PRD. Contributions from solvents usage were highest at DongGuan, an industrial site. At XinKen, the solvents and coatings had the largest percentage of 31% probably due to the influence of its upwind area of DongGuan. The local biomass burning was also found to be a noticeable source at XK.

Importance of chlorine speciation on de novo formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans.

PubMed

Wikström, Evalena; Ryan, Shawn; Touati, Abderrahmane; Telfer, Marnie; Tabor, Dennis; Gullett, Brian K

2003-03-15

The role of chlorine speciation on de novo formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs) has been studied thoroughly in an entrained flow reactor during simulated waste combustion. The effects of gas-phase chlorine species such as chlorine (Cl2), hydrogen chloride (HCl), and chlorine radicals (Cl*), as well as ash-bound chlorine, on PCDD/F de novo formation were isolated for investigation. The ash-bound chlorine alone was observed to be a sufficient chlorine source for PCDD/F formation. The addition of HCl to the system did not influence the yields of the PCDDs/Fs nor the degree of chlorination due to its poor chlorinating ability. Addition of 200 ppm of Cl2 to the ash-feed system resulted in increased PCDD/F yields, especially for the octa- and hepta-chlorinated congeners. Altering the reaction temperature to enable the presence of only Cl2 to the system did not change the yields of PCDD/F compared to those when both Cl2/Cl* were present. However, comparison between ash-bound and gas-phase chlorine, the latter at a concentration typical of a realistic combustion process, revealed ash-bound chlorine to be the more important chlorine source for de novo formation of PCDD/F in a full-scale incinerator.

Development of a universal solvent for the decontamination of acidic liquid radioactive wastes

NASA Astrophysics Data System (ADS)

Todd, T. A.; Brewer, K. N.; Law, J. D.; Wood, D. J.; Herbest, R. S.; Romanovskiy, V. N.; Esimantovskiy, V. M.; Smirnov, I. V.; Babain, V. A.

1999-01-01

A teritiary solvent containing chlorinated cobalt dicarbollide, polyethylene glycol and diphenylcarbamoylmethylphosphine oxide was evaluated in different non-nitroaromatic diluents for the separation of cesium, strontium, actinides and rare earth elements from acidic liquid radioactive waste. Decontamination factors of >95% for Cs, 99.7% for Sr, and 99.99% for actinides were achieved in four successive batch contacts using actual radioactive waste. Pilot plant testing in centrifugal contactors using simulated wastes, has demonstrated removal of >99% of all targeted ions.

Conversion from solvent rinsable fluxes to aqueous rinsable fluxes for hot oil solder leveling

NASA Astrophysics Data System (ADS)

1992-03-01

A water rinsable flux was evaluated for hot oil solder leveling of printed wiring boards. The previously used rosin-activated flux required a solvent containing a chlorinated hydrocarbon for removing the flux residues after soldering. The water rinsable flux requires hot water or a solution of hot detergent for removing flux residues after smoldering. The water rinsable flux produced an acceptable soldered surface. Flux residues were removed by either hot water (120 F) or a solution of hot detergent (120 F).

Ozone depletion and chlorine loading potentials

NASA Technical Reports Server (NTRS)

Pyle, John A.; Wuebbles, Donald J.; Solomon, Susan; Zvenigorodsky, Sergei; Connell, Peter; Ko, Malcolm K. W.; Fisher, Donald A.; Stordal, Frode; Weisenstein, Debra

1991-01-01

The recognition of the roles of chlorine and bromine compounds in ozone depletion has led to the regulation or their source gases. Some source gases are expected to be more damaging to the ozone layer than others, so that scientific guidance regarding their relative impacts is needed for regulatory purposes. Parameters used for this purpose include the steady-state and time-dependent chlorine loading potential (CLP) and the ozone depletion potential (ODP). Chlorine loading potentials depend upon the estimated value and accuracy of atmospheric lifetimes and are subject to significant (approximately 20-50 percent) uncertainties for many gases. Ozone depletion potentials depend on the same factors, as well as the evaluation of the release of reactive chlorine and bromine from each source gas and corresponding ozone destruction within the stratosphere.

CHARACTERIZATION OF FRACTURED BEDROCK FOR STEAM INJECTION

EPA Science Inventory

The most difficult setting in which to conduct groundwater remediation is that where chlorinated solvents have penetrated fractured bedrock. To demonstrate the potential viability of steam injection as a means of groundwater clean-up in this type of environment, steam will be in...

EVALUATION OF PERMEABLE REACTIVE BARRIER PERFORMANCE: A TRI-AGENCY INITIATIVE

EPA Science Inventory

The permeable reactive barrier (PRB) technology represents a passive option for long-term treatment of ground-water contamination. PRBs are a potentially more cost-effective treatment option for a variety of dissolved contaminants, such as certain types of chlorinated solvents, ...

LONG TERM PERFORMANCE MONITORING OF A PRB FOR REMEDIATION OF CHLORINATED SOLVENTS AND CHROMIUM

EPA Science Inventory

Permeable reactive barriers (PRB's) are an emerging, alternative in-situ approach for remediating groundwater contamination that combine subsurface fluid flow management with a passive chemical treatment zone. The few pilot and commercial installations which have been implemented...

Use of Additives in Bioremediation of Contaminated Groundwater and Soil

EPA Science Inventory

This chapter reviews application of additives used in bioremediation of chlorinated solvents and fuels for groundwater and soil remediation. Soluble carbon substrates are applicable to most site conditions except aquifers with very high or very low groundwater flow. Slow-release ...

Models Show Subsurface Cracking May Complicate Groundwater Cleanup at Hazardous Waste Sites

EPA Science Inventory

Chlorinated solvents like trichloroethylene contaminate groundwater at numerous sites nationwide. This modeling study, conducted at the Air Force Institute of Technology, shows that subsurface cracks, either natural or due to the presence of the contaminant itself, may result in...

COMPOUND-SPECIFIC STABLE ISOTOPE ANALYSIS TO DEMONSTRATE IN-SITU MTBE BIOTRANSFORMATION

EPA Science Inventory

Change of stable isotope composition of organic contaminants (isotopic fractionation) is a useful indicator of biotransformation. Most of applications to date are in the area of chlorinated solvents and recently BTEX, MTBE and TBA. Chemical reactions (biotic- and abiotic transfor...

Transport of Organic Solutes in Clay Formations

EPA Science Inventory

The research is a pilot investigation for the SERDP (Strategic Environmental Research and Development Program, DoD) founded project, Impact of Clay-DNAPL Interactions on Transport and Storage of Chlorinated Solvents in Low Permeability Zones, from 2010-2012. The report tries to s...

STEAM INJECTION INTO FRACTURED LIMESTONE AT LORING AIR FORCE BASE

EPA Science Inventory

A research project on steam injection for the remediation of spent chlorinated solvents from fractured limestone was recently undertaken at the former Loring AFB in Limestone, ME. Participants in the project include the Maine Department of Environmental Protection, EPA Region I,...

Synthesis and evaluation of sensitizer drug photorelease chemistry: Micro-optic method applied to singlet oxygen generation and drug delivery

NASA Astrophysics Data System (ADS)

Ghosh, Goutam

This thesis summarizes a new micro-optic method for singlet oxygen generation and sensitizer drug delivery, which include i) synthesis and evaluation of a first generation device for drug delivery from native and fluorinated silica probe tips, ii) synthesis of PEG conjugated sensitizers to study phototoxicity in ovarian cancer cells, and iii) synthesis and evaluation of tris-PEGylated chlorin conjugated fluorinated silica for its future integration into the device to use as a 2nd generation device. A first generation micro-optic device was developed that works by sparging O2 gas and light generating cytotoxic singlet oxygen that cleaves the covalently attached drug (sensitizer) from the probe tip at the distal end of the fiber. The aim is to develop a 1st and 2nd generation device for site specific delivery of photosensitizer and singlet oxygen to overcome the challenges involved in systemic administration of the sensitizer. Synthesis and evaluation of drug (pheophorbide-a) delivery applying micro-optic method from native and fluorinated silica probe tip was achieved. The amount of sensitizer photocleavage depends on the loading level of sensitizer onto the probe tips. We also found that photorelease efficiency depends on the nature of the solvents where sensitizer is photocleaved. For example, no photorelease was observed in an aqueous solvent where sensitizer remained adsorbed to the native silica probe-tip. But, 90% photocleavage was obtained in octanol. A significant amount of photosensitizer (formate ester of pyropheophorbide- a) diffused into the liposome when photocleavage study was carried out in liposome. Substantial increase of photorelease was observed in organic solvent when pyropheophorbide-a (PPa) sensitizer was attached to the partially fluorinated porous Vycor glass. We also explored sensitizer photorelease from the fluorinated silica surface at various temperatures and we found that autocatalytic photorelease happened at room temperature and above. No photorelease was observed at low temperature. Chlorin e6 and its one, two and three short chain methoxy triethylene glycol (PEG) conjugated derivatives were synthesized. A comparative study of photocytotoxicity and cellular uptake between each showed that 17 3,152,131- chlorin e6 methoxy triethylene glycol triester has the highest photocytotoxic activity and uptake by ovarian OVCAR-5 cancer cells. Therefore, we decided to load three short chain PEG conjugated chlorin e6 onto the silica surface through spacer alkene for delivery via a fiber-optic probe tip. In order to load chlorin e6-triPEG ester conjugate, in chapter 4, we explored different synthetic strategies. We have been successful in synthesizing spacer alkene succinate linker conjugated chlorin e6 -tri PEG ester, which was attached to the fiber-optic probe tip. Reactions were carried out in mild conditions to avoid detachment of the PEG ester from the carboxylic acid sites of chlorin. Photocleavage of the triPEG modified fluorinated probe tip system was studied in n-butanol.

Transport and transformations of chlorinated-solvent contamination in a saprolite and fractured rock aquifer near a former wastewater-treatment plant, Greenville, South Carolina

USGS Publications Warehouse

Vroblesky, D.A.; Bradley, P.M.; Lane, J.W.; Robertson, J.F.

1997-01-01

The transport and fate of chlorinated-ethene contamination was investigated in a fractured-rock aquifer downgradient from a wastewater-treatment plant at a gas-turbine manufacturing facility in Greenville, South Carolina. A vapor-diffusion-sampler technique, developed for this investigation, located fracture zones that discharged contaminated ground water to surface water. The distribution of chlorinated compounds and sulfate, comparison of borehole geophysical data, driller's logs, and the aquifer response to pumpage allowed subsurface contaminant-transport pathways to be delineated.The probable contaminant-transport pathway from the former aeration lagoon was southward. The probable pathway of contaminant transport from the former sludge lagoon was southward to and beneath Little Rocky Creek. South of the creek, the major pathway of contaminant transport appeared to be at a depth of approximately 80 to 107 feet below land surface. The contaminant-transport pathway from the former industrial lagoon was not readily discernible from existing data. A laboratory investigation, as well as examination of ground- water-chemistry data collected during this investigation and concentrations of chlorinated compounds collected during previous investigations,indicates that higher chlorinated compounds are being degraded to lower-chlorinated compounds in the contaminated aquifer. The approaches used in this investigation, as well as the findings, have potential application to other fractured-rock aquifers contaminated by chlorinated ethenes.

Formation of toxic iodinated disinfection by-products from compounds used in medical imaging.

PubMed

Duirk, Stephen E; Lindell, Cristal; Cornelison, Christopher C; Kormos, Jennifer; Ternes, Thomas A; Attene-Ramos, Matias; Osiol, Jennifer; Wagner, Elizabeth D; Plewa, Michael J; Richardson, Susan D

2011-08-15

Iodinated X-ray contrast media (ICM) were investigated as a source of iodine in the formation of iodo-trihalomethane (iodo-THM) and iodo-acid disinfection byproducts (DBPs), both of which are highly genotoxic and/or cytotoxic in mammalian cells. ICM are widely used at medical centers to enable imaging of soft tissues (e.g., organs, veins, blood vessels) and are designed to be inert substances, with 95% eliminated in urine and feces unmetabolized within 24 h. ICM are not well removed in wastewater treatment plants, such that they have been found at elevated concentrations in rivers and streams (up to 100 μg/L). Naturally occurring iodide in source waters is believed to be a primary source of iodine in the formation of iodo-DBPs, but a previous 23-city iodo-DBP occurrence study also revealed appreciable levels of iodo-DBPs in some drinking waters that had very low or no detectable iodide in their source waters. When 10 of the original 23 cities' source waters were resampled, four ICM were found--iopamidol, iopromide, iohexol, and diatrizoate--with iopamidol most frequently detected, in 6 of the 10 plants sampled, with concentrations up to 2700 ng/L. Subsequent controlled laboratory reactions of iopamidol with aqueous chlorine and monochloramine in the absence of natural organic matter (NOM) produced only trace levels of iodo-DBPs; however, when reacted in real source waters (containing NOM), chlorine and monochloramine produced significant levels of iodo-THMs and iodo-acids, up to 212 nM for dichloroiodomethane and 3.0 nM for iodoacetic acid, respectively, for chlorination. The pH behavior was different for chlorine and monochloramine, such that iodo-DBP concentrations maximized at higher pH (8.5) for chlorine, but at lower pH (6.5) for monochloramine. Extracts from chloraminated source waters with and without iopamidol, as well as from chlorinated source waters with iopamidol, were the most cytotoxic samples in mammalian cells. Source waters with iopamidol but no disinfectant added were the least cytotoxic. While extracts from chlorinated and chloraminated source waters were genotoxic, the addition of iopamidol enhanced their genotoxicity. Therefore, while ICM are not toxic in themselves, their presence in source waters may be a source of concern because of the formation of highly toxic iodo-DBPs in chlorinated and chloraminated drinking water.

STEAM INJECTION REMEDIATION IN FRACTURED BEDROCK AT LORING AIR FORCE BASE

EPA Science Inventory

Contaminated groundwater occurs at many Superfund, RCRA, and Brownfields sites. Chlorinated solvents which can form a dense nonaqueous phase (DNAPL) when released to the subsurface can pose an extreme challenge for remediation, as DNAPLs are often difficult to locate and even ha...

DEVELOPMENT OF BIOPLUME 4 MODEL FOR FUELS AND CHLORINATED SOLVENT BIODEGRADATION

EPA Science Inventory

The Bioplume model has been in development and use for modeling biodegradation and natural attenuation since the late 1980s. Bioplume 1 focused on aerobic biodegradation of BTEX. Bioplume II simulated oxygen and hydrocarbons and simulated biodegradation using an instantaneous r...

REMOVAL OF CHLORINATED ALKENE SOLVENTS FROM DRINKING WATER BY VARIOUS REVERSE OSMOSIS MEMBRANES

EPA Science Inventory

Historically, membranes have been used to desalinate water. As new membrane materials are developed, traditional water treatment schemes may incorporate membrane technologies, such as reverse osmosis, to address a variety of new concerns such as low molecular weight volatile org...

STREAM INJECTION INTO FRACTURE BEDROCK AT LORING AFB

EPA Science Inventory

The Quarry at the former Loring Air Force Base in Limestone, Maine, was used for the disposal of drums containing spent chlorinated solvents, mainly tetrachloroethene (PCE). After closure of the base, surface geophysics were used to locate the drums, and they were removed. Subs...

DEVELOPMENT OF BIOPLUME4 MODEL FOR FUELS AND CHLORINATED SOLVENT BIODEGRADATION

EPA Science Inventory

The Bioplume model has been in development and use for modeling biodegradation and natural attenuation since the late 80's. Bioplume I focused on aerobic biodegradation of BTEX. Bioplume II simulated oxygen and hydrocarbons and simulated biodegradation using an instantaneous re...

Long-Term Capacity of Plant Mulch to Remediate Trichloroethylene in Groundwater

EPA Science Inventory

Passive reactive barriers are commonly used to treat groundwater that is contaminated with chlorinated solvents such as trichloroethylene (TCE). A number of passive reactive barriers have been constructed with plant mulch as the reactive medium. The TCE is removed in these barr...

Monitored Natural Attenuation of Chlorinated Solvent Plumes

EPA Science Inventory

The chapter provides a synopsis of current applications of monitored natural attenuation (MNA) as a remedy at hazardous waste sites, and reviews the expectations of the U.S. Environmental Protection Agency for MNA as a remedy. It provides a detailed case study of the application...

The Role of Magnetite in In Situ Biogeochemical Transformation

EPA Science Inventory

The former Twin Cities Army Ammunition Plant (TCAAP) is located just north of St. Paul, Minnesota. Disposal of chlorinated solvents on the TCAAP contaminated groundwater in the shallow, unconsolidated sand aquifer with TCE and cis-DCE. Concentrations of TCE and cis-DCE rapidly ...

SOLUBILIZATION AND MICROEMULSIFICATION OF CHLORINATED SOLVENTS USING DIRECT FOOD ADDITIVE (EDIBLE) SURFACTANTS (JOURNAL)

EPA Science Inventory

Surfactant enhanced subsurface remediation is being evaluated as an innovative technology to expedite contaminant extraction from the subsurface. Regulatory approval of this technology will likely be enhanced by use of surfactants with FDA direct food additive status ("edible" su...

DESIGN AND OPERATION OF A HORIZONTAL WELL, IN SITU BIOREMEDIATION SYSTEM

EPA Science Inventory

A large field demonstration using nutrient addition to stimulate insitu anaerobic bioremediation of chlorinated solvent contaminated soil and ground water was performed at the former U.S. Department of Energy Pinellas Plant in Largo, Florida, from January through June, 1997. Ins...

Biodegradation potential of chlorinated solvents in ground water at the Naval Surface Warfare Center, Louisville, Kentucky, July 1999 to February 2000

USGS Publications Warehouse

Vroblesky, Don A.; Bradley, Paul M.; Petkewich, Matthew D.; Casey, Clifton C.

2001-01-01

The U.S. Geological Survey, in cooperation with the U.S. Department of the Navy, Southern Division Naval Facilities Engineering Command, investigated the potential for biodegradation of chlorinated solvents in ground water at the Naval Surface Warfare Center (also known as the Naval Ordnance Station, or the station), Louisville, Kentucky. The subsurface down to at least 100 feet at the station is characterized, from shallowest to deepest, by overburden deposits, a shale layer, and limestone. In general, all of the strata are poorly permeable. The permeable zones of the overburden and the limestone make up the overburden aquifer and the bedrock aquifer, respectively. Observed concentrations of redox-sensitive solutes suggest that the predominant anaerobic terminal electron accepting process in the overburden aquifer can shift between iron reduction and sulfate reduction, possibly as a result of rainfall-induced oxidation events. Daughter-product concentrations and laboratory experiments indicate that a variety of mechanisms, including reductive dechlorination and cometabolic oxidation, appear to be actively

Treatment of chlorinated solvents by TiO2 photocatalysis and photo-Fenton: influence of operating conditions in a solar pilot plant.

PubMed

Rodríguez, S Malato; Gálvez, J Blanco; Rubio, Manuel I Maldonado; Ibáñez, P Fernández; Gernjak, W; Alberola, I Oller

2005-01-01

Titanium dioxide photocatalysis (using 20 0mg l(-1) of TiO2), under aerobic and anaerobic conditions, and photo-Fenton (2 and 56 mg l(-1) iron) were applied to the treatment of different NBCS (non-biodegradable chlorinated solvents), such as dichloroethane, dichloromethane and trichloromethane dissolved in water at 50 mg l(-1). All the tests were performed in a 35-l solar pilot plant with compound parabolic collectors (CPCs) under natural illumination. The two solar treatments were compared with attention to chloride release and TOC mineralisation, as the main parameters. Photo-Fenton was found to be the more appropriate treatment for these compounds, assuming volatilisation as a drawback of photocatalytic degradation of NBCS dissolved in water. In this context, several operating parameters related to NBCS degradation, e.g., treatment time, temperature, hydrogen peroxide consumption and volatility of parent compounds are discussed. The correct choice of operating conditions can very often diminish the problem of volatilisation during treatment.

Biodegradation of chlorinated ethenes at a karst site in middle Tennessee

USGS Publications Warehouse

Byl, Thomas Duane; Williams, Shannon D.

2000-01-01

This report presents results of field and laboratory investigations examining the biodegradation of chlorinated ethenes in a karst aquifer contaminated with trichloroethylene (TCE). The study site, located in Middle Tennessee, was selected because of the presence of TCE degradation byproducts in the karst aquifer and available site hydrologic and chlorinated-ethene information. Additional chemical, biological, and hydrologic data were gathered to evaluate whether the occurrence of TCE degradation byproducts in the karst aquifer was the result of biodegradation within the aquifer or simply transport into the aquifer. Geochemical analysis established that sulfate-reducing conditions, essential for reductive dechlorination of chlorinated solvents, existed in parts of the contaminated karst aquifer. Other areas of the aquifer fluctuated between anaerobic and aerobic conditions and contained compounds associated with cometabolism, such as ethane, methane, ammonia, and dissolved oxygen. A large, diverse bacteria population inhabits the contaminated aquifer. Bacteria known to biodegrade TCE and other chlorinated solvents, such as sulfate-reducers, methanotrophs, and ammonia-oxidizers, were identified from karst-aquifer water using the RNA-hybridization technique. Results from microcosms using raw karst-aquifer water found that aerobic cometabolism and anaerobic reductive-dechlorination degradation processes were possible when appropriate conditions were established in the microcosms. These chemical and biological results provide circumstantial evidence that several biodegradation processes are active in the aquifer. Additional site hydrologic information was developed to determine if appropriate conditions persist long enough in the karst aquifer for these biodegradation processes to be significant. Continuous monitoring devices placed in four wells during the spring of 1998 indicated that pH, specific conductance, dissolved oxygen, and oxidation-reduction potentials changed very little in areas isolated from active ground-water flow paths. These stable areas in the karst aquifer had geochemical conditions and bacteria conducive to reductive dechlorination of chlorinated ethenes. Other areas of the karst aquifer were associated with active ground-water flow paths and fluctuated between anaerobic and aerobic conditions in response to rain events. Associated with this dynamic environment were bacteria and geochemical conditions conducive to cometabolism. In summary, multiple lines of evidence developed from chemical, biological, and hydrologic data demonstrate that a variety of biodegradation processes are active in this karst aquifer.

Phytoscreening for chlorinated solvents using rapid in vitro SPME sampling: Application to urban plume in Verl, Germany

USGS Publications Warehouse

Limmer, M.A.; Balouet, J.-C.; Karg, F.; Vroblesky, D.A.; Burken, J.G.

2011-01-01

Rapid detection and delineation of contaminants in urban settings is critically important in protecting human health. Cores from trees growing above a plume of contaminated groundwater in Verl, Germany, were collected in 1 day, with subsequent analysis and plume mapping completed over several days. Solid-phase microextraction (SPME) analysis was applied to detect tetrachloroethene (PCE) and trichloroethene (TCE) to below nanogram/liter levels in the transpiration stream of the trees. The tree core concentrations showed a clear areal correlation to the distribution of PCE and TCE in the groundwater. Concentrations in tree cores were lower than the underlying groundwater, as anticipated; however, the tree core water retained the PCE:TCE signature of the underlying groundwater in the urban, populated area. The PCE:TCE ratio can indicate areas of differing degradation activity. Therefore, the phytoscreening analysis was capable not only of mapping the spatial distribution of groundwater contamination but also of delineating zones of potentially differing contaminant sources and degradation. The simplicity of tree coring and the ability to collect a large number of samples in a day with minimal disruption or property damage in the urban setting demonstrates that phytoscreening can be a powerful tool for gaining reconnaissance-level information on groundwater contaminated by chlorinated solvents. The use of SPME decreases the detection level considerably and increases the sensitivity of phytoscreening as an assessment, monitoring, and phytoforensic tool. With rapid, inexpensive, and noninvasive methods of detecting and delineating contaminants underlying homes, as in this case, human health can be better protected through screening of broader areas and with far faster response times. ?? 2011 American Chemical Society.

THE EFFECT OF CHLORINE EMISSIONS ON TROPOSPHERIC OZONE IN THE UNITED STATES

EPA Science Inventory

The effect of chlorine emissions on atmospheric ozone in the continental United States was evaluated. Atmospheric chlorine chemistry was combined with the carbon bond mechanism and incorporated into the Community Multiscale Air Quality model. Sources of chlorine included anthrop...

Pilot Field Test of Electrokinetically-Delivered and Thermally Activated Persulfate (EKTAP) for Remediation of Chlorinated Solvents in Clay

NASA Astrophysics Data System (ADS)

O'Carrol, D. M.; Head, N.; Chowdhury, A. I.; Inglis, A.; Garcia, A. N.; Reynolds, D. A.; Hayman, J.; Hogberg, D.; Austrins, L. M.; Sidebottom, A.; Auger, M.; Eimers, J.; Gerhard, J.

2017-12-01

Remediation of low-permeability soils that are contaminated with chlorinated solvents is challenging. In-situ chemical oxidation (ISCO) with persulfate is promising, however, the delivery of the oxidant by hydraulic gradient is limited in low-permeability soils. Electrokinetic (EK) enhanced transport of amendments has shown the potential to overcome these limitations. In particular, the combined technology of EK-delivered and thermally activated persulfate (EKTAP) has been recently demonstrated in the laboratory as promising in these challenging environments (Chowdhury A. I. (2016) Hydraulic and Electrokinetic Delivery of Remediants for In-situ Remediation. Electronic Thesis and Dissertation Repository, Paper 4135). This study presents the first pilot field test to evaluate EKTAP to enhance the distribution and effectiveness of persulfate in clayey soil. The pilot field test was conducted at a contaminated site formerly occupied by a chlorinated solvent production facility. In the EK transport phase, 925 L of 40 g/L persulfate was injected over 57 days, during which 9A of direct current (DC) was applied between two electrodes spaced 3 m apart. In the subsequent heating phase, 10A of alternate current (AC) was applied across the same electrodes for an additional 70 days. Extensive sampling of soil and groundwater in this EKTAP cell were compared to those from two parallel control cells, one with EK only and one with no electrodes. Results indicated that EK can significantly increase transport rates of persulfate in clayey soil. Persulfate activation primarily occurred in the period of DC application, indicating that the natural reduction capacity of the clay soil had a significant impact on persulfate decomposition. Temperature mapping indicated that AC current was able to increase soil temperatures, validating the EKTAP concept. Degradation of chlorinated compounds, in particular, 1-2, dichloroethane (1,2- DCA), was observed to be substantial in areas of persulfate delivery. Studies are ongoing to evaluate the mineral oxidation of the persulfate and how to optimize the system for both EK and ERH applications. This study nevertheless demonstrates for the first time at the field scale that EKTAP can result in enhanced amendment transport and remediation of low permeability strata.

Hydrous pyrolysis/oxidation process for in situ destruction of chlorinated hydrocarbon and fuel hydrocarbon contaminants in water and soil

DOEpatents

Knauss, Kevin G.; Copenhaver, Sally C.; Aines, Roger D.

2000-01-01

In situ hydrous pyrolysis/oxidation process is useful for in situ degradation of hydrocarbon water and soil contaminants. Fuel hydrocarbons, chlorinated hydrocarbons, polycyclic aromatic hydrocarbons, petroleum distillates and other organic contaminants present in the soil and water are degraded by the process involving hydrous pyrolysis/oxidation into non-toxic products of the degradation. The process uses heat which is distributed through soils and water, optionally combined with oxygen and/or hydrocarbon degradation catalysts, and is particularly useful for remediation of solvent, fuel or other industrially contaminated sites.

40 CFR 63.1218 - What are the standards for hydrochloric acid production furnaces that burn hazardous waste?

Code of Federal Regulations, 2011 CFR

2011-07-01

... paragraph (a)(5) of this section; (2) For mercury, hydrogen chloride and chlorine gas emissions in excess of... source as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess of the levels... source as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess of the levels...

Test plan for Geo-Cleanse{reg_sign} demonstration (in situ destruction of dense non-aqueous phase liquid (DNAPL))

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jerome, K.M.; Looney, B.B.; Accorsi, F.

1996-09-01

Soils and groundwater beneath an abandoned process sewer line in the A/M Area of the Savannah River Site (SRS) contain elevated levels of volatile organic compounds, specifically trichloroethylene (TCE) and tetrachloroethylene (PCE), two common chlorinated solvents. These compounds have low aqueous solubilities, thus when released to the subsurface in sufficient quantity, tend to exist as immiscible fluids or nonaqueous phase liquids (NAPLs). Because chlorinated solvents are also denser than water, they are referred to by the acronym DNAPLs, or dense non-aqueous phase liquids. Technologies targeted at the efficient characterization or removal of DNAPL are not currently proven. For example, mostmore » DNAPL studies rely on traditional soil and water sampling and the fortuitous observation of immiscible solvent. Once DNAPL is identified, soil excavation (which is only applicable to small contained spill sites) is the only proven cleanup method. New cleanup approaches based on destruction of DNAPL either in situ or ex situ have been proposed and tested at the pilot scale. The proposed demonstration, as described in this report will evaluate the applicability to DNAPL plumes of a technology proven for in situ destruction of light non-aqueous phase liquids (LNAPLs) such as oils.« less

Point-of-use chlorination of turbid water: results from a field study in Tanzania.

PubMed

Mohamed, Hussein; Brown, Joe; Njee, Robert M; Clasen, Thomas; Malebo, Hamisi M; Mbuligwe, Steven

2015-06-01

Household-based chlorine disinfection is widely effective against waterborne bacteria and viruses, and may be among the most inexpensive and accessible options for household water treatment. The microbiological effectiveness of chlorine is limited, however, by turbidity. In Tanzania, there are no guidelines on water chlorination at household level, and limited data on whether dosing guidelines for higher turbidity waters are sufficient to produce potable water. This study was designed to assess the effectiveness of chlorination across a range of turbidities found in rural water sources, following local dosing guidelines that recommend a 'double dose' for water that is visibly turbid. We chlorinated water from 43 sources representing a range of turbidities using two locally available chlorine-based disinfectants: WaterGuard and Aquatabs. We determined free available chlorine at 30 min and 24 h contact time. Our data suggest that water chlorination with WaterGuard or Aquatabs can be effective using both single and double doses up to 20 nephelometric turbidity units (NTU), or using a double dose of Aquatabs up to 100 NTU, but neither was effective at turbidities greater than 100 NTU.

MICROBIAL COMETABOLISM OF RECALCITRANT CHEMICALS IN CONTAMINATED AIR STREAMS

EPA Science Inventory

Chlorinated Solvents: The treatment system consists of a laboratory-scale hollow fiber membrane (HFM) module containing a center baffle and a radial cross-flow pattern on the shell side of the fibers. The shell and lumen fluids are contacting in a counter-current f...

NATURAL ATTENUATION OF CHLORINATED SOLVENTS AT MULTIPLE AIR FORCE BASE DEMONSTRATION SITES

EPA Science Inventory

Natural attenuation treatability studies(TSs) were conducted at 14 US Air Force bases. Only sites where biodegradation of CAHs was suspected were selected for the study. The major initiative was to evaluate the effectiveness of monitored natural attenuation(MNA) at sites contam...

LABORATORY SCALE EVALUATION OF HYDRA-TONE GRAFF-OFF™ COCONUT OIL BASED DEGREASER

EPA Science Inventory

This technical and economic assessment evaluated the effectiveness of a biodegradable, coconut oil-based degreaser called Graff-Off™. In immersion (cold) cleaning and rinse tests, Graff-Off™ was compared to a conventional chlorinated solvent 1,1,1 trichloroethane (TCA) and to an ...

Application of Stable Isotope Analysis to Understand Behavior of Chlorinated Solvents

EPA Science Inventory

The traditional approach of monitoring a reduction in the concentrations of contaminants at sites does not always offer compelling documentation that the contaminants are actually being degraded. When data on concentrations are the only data available, it is may be difficult or i...

Photo-oxidation method using MoS2 nanocluster materials

DOEpatents

Wilcoxon, Jess P.

2001-01-01

A method of photo-oxidizing a hydrocarbon compound is provided by dispersing MoS.sub.2 nanoclusters in a solvent containing a hydrocarbon compound contaminant to form a stable solution mixture and irradiating the mixture to photo-oxide the hydrocarbon compound. Hydrocarbon compounds of interest include aromatic hydrocarbon and chlorinated hydrocarbons. MoS.sub.2 nanoclusters with an average diameter less than approximately 10 nanometers are shown to be effective in decomposing potentially toxic aromatic and chlorinated hydrocarbons, such as phenol, pentachlorophenol, chlorinated biphenols, and chloroform, into relatively non-toxic compounds. The irradiation can occur by exposing the MoS.sub.2 nanoclusters and hydrocarbon compound mixture with visible light. The MoS.sub.2 nanoclusters can be introduced to the toxic hydrocarbons as either a MoS.sub.2 solution or deposited on a support material.

Detection and occurrence of chlorinated byproducts of bisphenol a, nonylphenol, and estrogens in drinking water of china: comparison to the parent compounds.

PubMed

Fan, Zhanlan; Hu, Jianying; An, Wei; Yang, Min

2013-10-01

This study applied a sensitive dansylation LC-MS/MS method to the investigation on the occurrence of bisphenol A (BPA), nonylphenol (NP), estrogens (E1 and E2), and their 11 chlorinated byproducts in 62 drinking water treatment plants (DWTPs) of 31 major cities across China. BPA (4.7-512 ng/L), NP (8.2-918 ng/L), and E1 (ND-9.9 ng/L) were widely detected in source waters, E2 was detected in less than half of the samples (ND-3.2 ng/L), while chlorinated byproducts were only detected in source waters of two DWTPs. In drinking water, chlorinated BPAs and monochloro-NP (MCNP) were detected in more than half of the samples with concentrations of 0.2-26.7 ng/L for monochloro-BPA (MCBPA), ND-6.3 ng/L for dichloro-BPA (DCBPA), ND-7.7 ng/L for trichloro-BPA (TCBPA), ND-4.8 ng/L for tetrachloro-BPA (TBBPA), and ND-13.3 ng/L for MCNP, while dichloro-E1 (DCE1, ND-0.2 ng/L) and dichloro-NP (DCNP, ND-1.6 ng/L) were less frequently detected (10/62 and 4/62). The production of chlorinated NPs in DWTPs was mainly influenced by the amount of NP in source water and chlorine added, while the concentrations of chlorinated BPAs in drinking waters were only found to be significantly correlated with those of BPA in source waters. Advanced treatment processes could be effective techniques for reducing target chlorinated byproducts in drinking water. This is the first report on the occurrence of chlorinated byproducts of BPA, NP, and estrogens in drinking water, and these chemicals should be considered when assessing the human risk of their parent compounds.

Evaluating four measures of water quality in clay pots and plastic safe storage containers in Kenya.

PubMed

Murphy, Jennifer L; Ayers, Tracy L; Knee, Jacqueline; Oremo, Jared; Odhiambo, Aloyce; Faith, Sitnah H; Nyagol, Ronald O; Stauber, Christine E; Lantagne, Daniele S; Quick, Robert E

2016-11-01

Household water treatment with chlorine can improve microbiological quality and reduce diarrhea. Chlorination is typically assessed using free chlorine residual (FCR), with a lower acceptable limit of 0.2 mg/L, however, accurate measurement of FCR is challenging with turbid water. To compare potential measures of adherence to treatment and water quality, we chlorinated recently-collected water in rural Kenyan households and measured total chlorine residual (TCR), FCR, oxidation reduction potential (ORP), and E. coli concentration over 72 h in clay and plastic containers. Results showed that 1) ORP served as a useful proxy for chlorination in plastic containers up to 24 h; 2) most stored water samples disinfected by chlorination remained significantly less contaminated than source water for up to 72 h, even in the absence of FCR; 3) TCR may be a useful proxy indicator of microbiologic water quality because it confirms previous chlorination and is associated with a lower risk of E. coli contamination compared to untreated source water; and 4) chlorination is more effective in plastic than clay containers presumably because of lower chlorine demand in plastic. Published by Elsevier Ltd.

In situ treatability testing of reductive dechlorination in wetland sediments

USGS Publications Warehouse

Lorah, M.M.; Majcher, E.; Jones, E.; Driedger, G.; Dworatzek, S.; Graves, D.

2005-01-01

In situ treatability testing was conducted in the discharge wetlands along West Branch Canal Creek at Aberdeen Proving Ground, MD. The potential for stimulating reductive dechlorination of 1,1,2,2-tetrachloroethane, tetrachloroethylene, trichloroethylene, and carbon tetrachloride in areas of preferential discharge or seeps was evaluated. Geological Survey that degrades chlorinated ethanes and ethylenes was tested using MICRO-Trac??? devices. At seep 3-4W, results of the C and BA MICRO-Trac??? treatments showed essentially no biodegradation of chlorinated solvents occurring under natural and bioaugmented conditions. Results of geochemical samples at this site indicated predominantly iron- and sulfate-reducing conditions consistent with the rapid discharge rates previously measured. The biostimulated treatment showed stimulation of methanogenic conditions and partial degradation of the parent chlorinated VOC to intermediate chlorinated compounds. The bioaugmented and bistimulated treatment showed the highest production of methane, the highest removal of parent compounds and intermediate daughter products, and the highest production of the non-chlorinated end product ethylene. This is an abstract of a paper presented at the proceedings of the 8th International In Situ and On-Site Bioremediation Symposium (Baltimore, MD 6/6-9/2005).

Assessment of In-Situ Reductive Dechlorination Using Compound-Specific Stable Isotopes, Functional-Gene Pcr, and Geochemical Data

PubMed Central

Carreón-Diazconti, Concepción; Santamaría, Johanna; Berkompas, Justin; Field, James A.; Brusseau, Mark L.

2010-01-01

Isotopic analysis and molecular-based bioassay methods were used in conjunction with geochemical data to assess intrinsic reductive dechlorination processes for a chlorinated-solvent contaminated site in Tucson, Arizona. Groundwater samples were obtained from monitoring wells within a contaminant plume comprising tetrachloroethene and its metabolites trichloroethene, cis-1,2-dichloroethene, vinyl chloride, and ethene, as well as compounds associated with free-phase diesel present at the site. Compound specific isotope (CSI) analysis was performed to characterize biotransformation processes influencing the transport and fate of the chlorinated contaminants. PCR analysis was used to assess the presence of indigenous reductive dechlorinators. The target regions employed were the 16s rRNA gene sequences of Dehalococcoides sp. and Desulfuromonas sp., and DNA sequences of genes pceA, tceA, bvcA, and vcrA, which encode reductive dehalogenases. The results of the analyses indicate that relevant microbial populations are present and that reductive dechlorination is presently occurring at the site. The results further show that potential degrader populations as well as biotransformation activity is non-uniformly distributed within the site. The results of laboratory microcosm studies conducted using groundwater collected from the field site confirmed the reductive dechlorination of tetrachloroethene to dichloroethene. This study illustrates the use of an integrated, multiple-method approach for assessing natural attenuation at a complex chlorinated-solvent contaminated site. PMID:19603638

The influence of in situ chemical oxidation on microbial community composition in groundwater contaminated with chlorinated solvents.

PubMed

Sercu, Bram; Jones, Antony D G; Wu, Cindy H; Escobar, Mauricio H; Serlin, Carol L; Knapp, Timothy A; Andersen, Gary L; Holden, Patricia A

2013-01-01

In situ chemical oxidation with permanganate has become an accepted remedial treatment for groundwater contaminated with chlorinated solvents. This study focuses on the immediate and short-term effects of sodium permanganate (NaMnO(4)) on the indigenous subsurface microbial community composition in groundwater impacted by trichloroethylene (TCE). Planktonic and biofilm microbial communities were studied using groundwater grab samples and reticulated vitreous carbon passive samplers, respectively. Microbial community composition was analyzed by terminal restriction fragment length polymorphism and a high-density phylogenetic microarray (PhyloChip). Significant reductions in microbial diversity and biomass were shown during NaMnO(4) exposure, followed by recovery within several weeks after the oxidant concentrations decreased to <1 mg/L. Bray-Curtis similarities and nonmetric multidimensional scaling showed that microbial community composition before and after NaMnO(4) was similar, when taking into account the natural variation of the microbial communities. Also, 16S rRNA genes of two reductive dechlorinators (Desulfuromonas spp. and Sulfurospirillum spp.) and diverse taxa capable of cometabolic TCE oxidation were detected in similar quantities by PhyloChip across all monitoring wells, irrespective of NaMnO(4) exposure and TCE concentrations. However, minimal biodegradation of TCE was observed in this study, based on oxidized conditions, concentration patterns of chlorinated and nonchlorinated hydrocarbons, geochemistry, and spatiotemporal distribution of TCE-degrading bacteria.

40 CFR 63.1218 - What are the standards for hydrochloric acid production furnaces that burn hazardous waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... limits provided by paragraph (a)(5) of this section; (2) For mercury, hydrogen chloride and chlorine gas..., except for an area source as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess..., except for an area source as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess...

Impacts by point and diffuse micropollutant sources on the stream water quality at catchment scale

NASA Astrophysics Data System (ADS)

Petersen, M. F.; Eriksson, E.; Binning, P. J.; Bjerg, P. L.

2012-04-01

The water quality of surface waters is threatened by multiple anthropogenic pollutants and the large variety of pollutants challenges the monitoring and assessment of the water quality. The aim of this study was to characterize and quantify both point and diffuse sources of micropollutants impacting the water quality of a stream at catchment scale. Grindsted stream in western Jutland, Denmark was used as a study site. The stream passes both urban and agricultural areas and is impacted by severe groundwater contamination in Grindsted city. Along a 12 km reach of Grindsted stream, the potential pollution sources were identified including a pharmaceutical factory site with a contaminated old drainage ditch, two waste deposits, a wastewater treatment plant, overflow structures, fish farms, industrial discharges and diffuse agricultural and urban sources. Six water samples were collected along the stream and analyzed for general water quality parameters, inorganic constituents, pesticides, sulfonamides, chlorinated solvents, BTEXs, and paracetamol and ibuprofen. The latter two groups were not detected. The general water quality showed typical conditions for a stream in western Jutland. Minor impacts by releases of organic matter and nutrients were found after the fish farms and the waste water treatment plant. Nickel was found at concentrations 5.8 - 8.8 μg/l. Nine pesticides and metabolites of both agricultural and urban use were detected along the stream; among these were the two most frequently detected and some rarely detected pesticides in Danish water courses. The concentrations were generally consistent with other findings in Danish streams and in the range 0.01 - 0.09 μg/l; except for metribuzin-diketo that showed high concentrations up to 0.74 μg/l. The groundwater contamination at the pharmaceutical factory site, the drainage ditch and the waste deposits is similar in composition containing among others sulfonamides and chlorinated solvents (including vinyl chloride). Vinyl chloride concentrations surpassed Danish stream water quality criteria with a factor 10. The largest chemical impact occurs at the reach downstream Grindsted city revealing that the main contaminant groundwater discharge zones are found here. The contaminant plume from the factory site north of the stream is known to impact the stream whereas the impact by the old landfill south of the stream remains to be assessed. A conceptual model of the chemical impacts by the identified sources was made, and high impact was assigned to the contaminant plume from the factory site and to the diffuse sources of urban-use and agricultural pesticides. The next step will be a quantification of the sources, which will be presented at the conference.

Emerging nitrogenous disinfection byproducts: Transformation of the antidiabetic drug metformin during chlorine disinfection of water.

PubMed

Armbruster, Dominic; Happel, Oliver; Scheurer, Marco; Harms, Klaus; Schmidt, Torsten C; Brauch, Heinz-Jürgen

2015-08-01

As an environmental contaminant of anthropogenic origin metformin is present in the high ng/L- up to the low μg/L-range in most surface waters. Residues of metformin may lead to the formation of disinfection by-products during chlorine disinfection, when these waters are used for drinking water production. Investigations on the underlying chemical processes occurring during treatment of metformin with sodium hypochlorite in aqueous medium led to the discovery of two hitherto unknown transformation products. Both substances were isolated and characterized by HPLC-DAD, GC-MS, HPLC-ESI-TOF, (1)H-NMR and single-crystal X-ray structure determination. The immediate major chlorination product is a cyclic dehydro-1,2,4-triazole-derivate of intense yellow color (Y; C4H6ClN5). It is a solid chlorimine of limited stability. Rapid formation was observed between 10 °C and 30 °C, as well as between pH 3 and pH 11, in both ultrapure and tap water, even at trace quantities of reactants (ng/L-range for metformin, mg/L-range for free chlorine). While Y is degraded within a few hours to days in the presence of light, elevated temperature, organic solvents and matrix constituents within tap water, a secondary degradation product was discovered, which is stable and colorless (C; C4H6ClN3). This chloroorganic nitrile has a low photolysis rate in ambient day light, while being resistant to heat and not readily degraded in the presence of organic solvents or in the tap water matrix. In addition, the formation of ammonia, dimethylamine and N,N-dimethylguanidine was verified by cation exchange chromatography. Copyright © 2015 Elsevier Ltd. All rights reserved.

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

Aggregation of Adenovirus 2 in Source Water and Impacts on Disinfection by Chlorine

PubMed Central

Cromeans, Theresa L.; Metcalfe, Maureen G.; Humphrey, Charles D.; Hill, Vincent R.

2016-01-01

It is generally accepted that viral particles in source water are likely to be found as aggregates attached to other particles. For this reason, it is important to investigate the disinfection efficacy of chlorine on aggregated viruses. A method to produce adenovirus particle aggregation was developed for this study. Negative stain electron microscopy was used to measure aggregation before and after addition of virus particles to surface water at different pH and specific conductance levels. The impact of aggregation on the efficacy of chlorine disinfection was also examined. Disinfection experiments with human adenovirus 2 (HAdV2) in source water were conducted using 0.2 mg/L free chlorine at 5 °C. Aggregation of HAdV2 in source water (≥3 aggregated particles) remained higher at higher specific conductance and pH levels. However, aggregation was highly variable, with the percentage of particles present in aggregates ranging from 43 to 71 %. Upon addition into source water, the aggregation percentage dropped dramatically. On average, chlorination CT values (chlorine concentration in mg/L × time in min) for 3-log10 inactivation of aggregated HAdV2 were up to three times higher than those for dispersed HAdV2, indicating that aggregation reduced the disinfection rate. This information can be used by water utilities and regulators to guide decision making regarding disinfection of viruses in water. PMID:26910058

Aggregation of Adenovirus 2 in Source Water and Impacts on Disinfection by Chlorine.

PubMed

Kahler, Amy M; Cromeans, Theresa L; Metcalfe, Maureen G; Humphrey, Charles D; Hill, Vincent R

2016-06-01

It is generally accepted that viral particles in source water are likely to be found as aggregates attached to other particles. For this reason, it is important to investigate the disinfection efficacy of chlorine on aggregated viruses. A method to produce adenovirus particle aggregation was developed for this study. Negative stain electron microscopy was used to measure aggregation before and after addition of virus particles to surface water at different pH and specific conductance levels. The impact of aggregation on the efficacy of chlorine disinfection was also examined. Disinfection experiments with human adenovirus 2 (HAdV2) in source water were conducted using 0.2 mg/L free chlorine at 5 °C. Aggregation of HAdV2 in source water (≥3 aggregated particles) remained higher at higher specific conductance and pH levels. However, aggregation was highly variable, with the percentage of particles present in aggregates ranging from 43 to 71 %. Upon addition into source water, the aggregation percentage dropped dramatically. On average, chlorination CT values (chlorine concentration in mg/L × time in min) for 3-log10 inactivation of aggregated HAdV2 were up to three times higher than those for dispersed HAdV2, indicating that aggregation reduced the disinfection rate. This information can be used by water utilities and regulators to guide decision making regarding disinfection of viruses in water.

Ground Water Issue Paper: Synthesis Report on State of Understanding of Chlorinated Solvent Transformation

EPA Science Inventory

The U.S. EPA (1999) provided clarification of its policy on the application of MNA as a remedy for contaminated sites, and defines this alternative as “the reliance on natural attenuation processes (within the context of a carefully controlled and monitored site cleanup approach)...

CHLORINATED SOLVENT MOVEMENT THROUGH PLANTS MONITORED BY FOURIER TRANSFORM INFRARED (FT-IR) SPECTROMETRY. (R825549C062)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

BUILDING DEFINED MIXED CULTURES TO BIODEGRADE DIVERSE MIXTURES OF CHLORINATED SOLVENTS

EPA Science Inventory

The major accomplishment that I can think of is the education of a Master’s student who is now out in practice working for a consulting engineering firm.  This project allowed him to develop expertise with biological treatment systems, which are widely used...

DEMONSTRATION OF A LIQUID CARBON DIOXIDE PROCESS FOR CLEANING METAL PARTS

EPA Science Inventory

The report gives results of a demonstration of liquid carbon dioxide (LCO2) as an alternative to chlorinated solvents for cleaning metal parts. It describes the LCO2 process, the parts tested, the contaminants removed, and results from preliminary laboratory testing and on-site d...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT, PCB DETECTION TECHNOLOGY, DEXSIL CORPORATION L2000DX ANALYZER

EPA Science Inventory

The L2000DX Analyzer (dimensions: 9 x 9.5 x 4.25 in.) is a field-portable ion-specific electrode instrument, weighing approximately 5 lb 12 oz, designed to quantify concentrations of PCBS, chlorinated solvents, and pesticides in soils, water, transformer oils, and surface wipes. ...

Using Concentrations of Methane and Gasoline Hydrocarbons in Soil Gas to Predict Vapor Intrusion of Benzene

EPA Science Inventory

Risk management of petroleum vapor intrusion has been a daunting and challenging task for the Underground Storage Tank Program. Because chlorinated solvents do not degrade in soil gas, techniques that focus on their properties and behavior can produce useful estimates. However, t...

Degradation of Environmental Contaminants with Water-Soluble Cobalt Catalysts: An Integrative Inorganic Chemistry Investigation

ERIC Educational Resources Information Center

Evans, Alexandra L.; Messersmith, Reid E.; Green, David B.; Fritsch, Joseph M.

2011-01-01

We present an integrative laboratory investigation incorporating skills from inorganic chemistry, analytical instrumentation, and physical chemistry applied to a laboratory-scale model of the environmental problem of chlorinated ethylenes in groundwater. Perchloroethylene (C[subscript 2]Cl[subscript 4], PCE) a common dry cleaning solvent,…

FIELD MEASUREMENT OF VAPOR INTRUSION RATES AT A PCE SITE (ABSTRACT ONLY)

EPA Science Inventory

A field study was performed to evaluate vapor intrusion (VI) of tetrachloroethylene (PCE) and other chlorinated solvents at a commercial retail site in Dallas, TX. The building is approximately 40 years old and once housed a dry cleaning operation. Results from an initial site ch...

CHLORINATED SOLVENT IMPACT AND REMEDIATION STRATEGIES FOR THE DRY CLEANING INDUSTRY

EPA Science Inventory

Additional funding has been received from the Advanced Technologies Program of the State of Texas by collaborators on this project, Dr. Herb Ward and Dr. Joseph Hughes. This follow-up study will provide a further in depth analysis of the benefits of bioremediation for...

Abiotic Removal of TCE and cis-DCE by Magnetite under Aerobic Conditions in Ground Water (Maryland)

EPA Science Inventory

The former Twin Cities Army Ammunition Plant (TCAAP) is located just north of St. Paul, Minnesota. Disposal of chlorinated solvents at the Building102 site on the TCAAP contaminated groundwater in the shallow, unconsolidated sand aquifer with TCE and cis-DCE. Concentrations of ...

The Use of Molecular and Genomic Techniques Applied to Microbial Diversity, Community Structure, and Activities at DNAPL and Metal Contaminated Sites

EPA Science Inventory

A wide variety of in situ subsurface remediation strategies have been developed to mitigate contamination by chlorinated solvent dense non-aqueous phase liquids (DNAPLS) and metals. Geochemical methods include: zerovalent iron emplacement, various electrolytic applications, elec...

Determination of six iodotrihalomethanes in drinking water in Korea.

PubMed

Woo, Bomi; Park, Ju-Hyun; Kim, Seungki; Lee, Jeongae; Choi, Jong-Ho; Pyo, Heesoo

2018-06-02

Trihalomethanes (THMs) are chemicals regulated by Environmental Protection Agency's first drinking water regulation issued after the passage of the Safe Drinking Water Act. Among THMs, iodotrihalomethanes (I-THMs) are produced by treating water containing iodides ion with chlorine or ozone. I-THMs are more carcinogenic and biotoxic than chlorinated or brominated THMs. The purpose of this study was to analyze of I-THMs in drinking water using the liquid-liquid extraction (LLE) method with various extraction solvents. The calibration curves ranged from 0.01 to 20 ng/mL and the correlation coefficient showed a good linearity of 0.99 or more. The method detection limit ranged from 0.01 to 0.10 ng/mL. The accuracy of the LLE method ranged from 99.43 to 112.40%, and its precision ranged from 1.10 to 10.36%. Good recoveries (71.35-118.60%) were obtained for spiked drinking water samples, demonstrating that the LLE method is suitable for the analysis of drinking water samples. Dichloroiodomethane, bromochloroiodomethane, and dibromoiodomethane were identified in drinking water collected from 70 places of water purification plants in Korea. The samples were classified by disinfection systems, regions, seasons, and water sources. The concentration of I-THMs in pre-/postchlorination facilities owing to excess chlorine usage was higher than in ozonization/postchlorination facilities. Moreover, the concentrations of I-THMs were high in the coastal region, because of the large amount of halide ions from the sea. There was no seasonal difference; however, the concentration of I-THMs in pre-/postchlorination facilities increased in spring and summer. The concentration of I-THMs in water sources was high in samples from the Geum River and the Yeongsan and Sumjin River. The concentration and detection frequency of I-THMs in Han River and Nakdong River were high in the coastal region, because of numerous pre-/postchlorination facilities and the abundance of halide ions from the ocean. Copyright © 2018 Elsevier B.V. All rights reserved.

Sewers as a source and sink of chlorinated-solvent groundwater contamination, Marine Corps Recruit Depot, Parris Island, South Carolina

USGS Publications Warehouse

Vroblesky, D.A.; Petkewich, M.D.; Lowery, M.A.; Landmeyer, J.E.

2011-01-01

Groundwater contamination by tetrachloroethene and its dechlorination products is present in two partially intermingled plumes in the surficial aquifer near a former dry-cleaning facility at Site 45, Marine Corps Recruit Depot, Parris Island, South Carolina. The northern plume originates from the vicinity of former above-ground storage tanks. Free-phase tetrachloroethene from activities in this area entered the groundwater. The southern plume originates at a nearby, new dry-cleaning facility, but probably was the result of contamination released to the aquifer from a leaking sanitary sewer line from the former dry-cleaning facility. Discharge of dissolved groundwater contamination is primarily to leaking storm sewers below the water table. The strong influence of sanitary sewers on source distribution and of storm sewers on plume orientation and discharge at this site indicates that groundwater-contamination investigators should consider the potential influence of sewer systems at their sites. ?? 2011, National Ground Water Association.

The Influence of Nitrogen Oxides on Chlorine Chemistry in Barrow, Alaska

NASA Astrophysics Data System (ADS)

McNamara, S. M.; Raso, A. R. W.; Wang, S.; Thanekar, S.; Fuentes, J. D.; Shepson, P. B.; Pratt, K.

2016-12-01

Active chlorine chemistry in the springtime Arctic boundary layer impacts the fate of atmospheric pollutants and greenhouse gases. Recent field studies have reported high amounts of molecular chlorine (Cl2), up to 400 parts per trillion (ppt), as well as the presence of chlorinated hydrocarbon oxidation products. However, our knowledge of Arctic chlorine chemistry is limited by a paucity of observations. The presence of nitrogen oxides (NOx) may influence the chlorine chemistry in this region. Here, we report chemical ionization mass spectrometry measurements of Cl2, chlorine monoxide (ClO), nitryl chloride (ClNO2), and dinitrogen pentoxide (N2O5), and NOx measurements at Barrow, AK during March-May 2016. To our knowledge, these data represent the first observations of ClNO2 in the Arctic. While the main source of NOx in a pristine Arctic environment is irradiated snow surfaces, anthropogenic sources can significantly enhance local NOx concentrations. The role of NOx in the activation and temporal trends of the reactive chlorine species are examined using a 0-D photochemical model. The prevalence of chlorine chemistry under elevated nitrogen oxide conditions may have significant impacts on the atmospheric composition in an increasingly polluted Arctic.

Volatile and organic compositions of sedimentary rocks in Yellowknife Bay, Gale crater, Mars.

PubMed

Ming, D W; Archer, P D; Glavin, D P; Eigenbrode, J L; Franz, H B; Sutter, B; Brunner, A E; Stern, J C; Freissinet, C; McAdam, A C; Mahaffy, P R; Cabane, M; Coll, P; Campbell, J L; Atreya, S K; Niles, P B; Bell, J F; Bish, D L; Brinckerhoff, W B; Buch, A; Conrad, P G; Des Marais, D J; Ehlmann, B L; Fairén, A G; Farley, K; Flesch, G J; Francois, P; Gellert, R; Grant, J A; Grotzinger, J P; Gupta, S; Herkenhoff, K E; Hurowitz, J A; Leshin, L A; Lewis, K W; McLennan, S M; Miller, K E; Moersch, J; Morris, R V; Navarro-González, R; Pavlov, A A; Perrett, G M; Pradler, I; Squyres, S W; Summons, R E; Steele, A; Stolper, E M; Sumner, D Y; Szopa, C; Teinturier, S; Trainer, M G; Treiman, A H; Vaniman, D T; Vasavada, A R; Webster, C R; Wray, J J; Yingst, R A

2014-01-24

H2O, CO2, SO2, O2, H2, H2S, HCl, chlorinated hydrocarbons, NO, and other trace gases were evolved during pyrolysis of two mudstone samples acquired by the Curiosity rover at Yellowknife Bay within Gale crater, Mars. H2O/OH-bearing phases included 2:1 phyllosilicate(s), bassanite, akaganeite, and amorphous materials. Thermal decomposition of carbonates and combustion of organic materials are candidate sources for the CO2. Concurrent evolution of O2 and chlorinated hydrocarbons suggests the presence of oxychlorine phase(s). Sulfides are likely sources for sulfur-bearing species. Higher abundances of chlorinated hydrocarbons in the mudstone compared with Rocknest windblown materials previously analyzed by Curiosity suggest that indigenous martian or meteoritic organic carbon sources may be preserved in the mudstone; however, the carbon source for the chlorinated hydrocarbons is not definitively of martian origin.

Volatile and organic compositions of sedimentary rocks in Yellowknife Bay, Gale crater, Mars

USGS Publications Warehouse

Ming, D. W.; Archer, P.D.; Glavin, D.P.; Eigenbrode, J.L.; Franz, H.B.; Sutter, B.; Brunner, A.E.; Stern, J.C.; Freissinet, C.; McAdam, A.C.; Mahaffy, P.R.; Cabane, M.; Coll, P.; Campbell, J.L.; Atreya, S.K.; Niles, P.B.; Bell, J.F.; Bish, D.L.; Brinckerhoff, W.B.; Buch, A.; Conrad, P.G.; Des Marais, D.J.; Ehlmann, B.L.; Fairén, A.G.; Farley, K.; Flesch, G.J.; Francois, P.; Gellert, Ralf; Grant, J. A.; Grotzinger, J.P.; Gupta, S.; Herkenhoff, K. E.; Hurowitz, J.A.; Leshin, L.A.; Lewis, K.W.; McLennan, S.M.; Miller, Karl E.; Moersch, J.; Morris, R.V.; Navarro- González, R.; Pavlov, A.A.; Perrett, G.M.; Pradler, I.; Squyres, S. W.; Summons, Roger E.; Steele, A.; Stolper, E.M.; Sumner, D.Y.; Szopa, C.; Teinturier, S.; Trainer, M.G.; Treiman, A.H.; Vaniman, D.T.; Vasavada, A.R.; Webster, C.R.; Wray, J.J.; Yingst, R.A.

2014-01-01

H2O, CO2, SO2, O2, H2, H2S, HCl, chlorinated hydrocarbons, NO, and other trace gases were evolved during pyrolysis of two mudstone samples acquired by the Curiosity rover at Yellowknife Bay within Gale crater, Mars. H2O/OH-bearing phases included 2:1 phyllosilicate(s), bassanite, akaganeite, and amorphous materials. Thermal decomposition of carbonates and combustion of organic materials are candidate sources for the CO2. Concurrent evolution of O2 and chlorinated hydrocarbons suggests the presence of oxychlorine phase(s). Sulfides are likely sources for sulfur-bearing species. Higher abundances of chlorinated hydrocarbons in the mudstone compared with Rocknest windblown materials previously analyzed by Curiosity suggest that indigenous martian or meteoritic organic carbon sources may be preserved in the mudstone; however, the carbon source for the chlorinated hydrocarbons is not definitively of martian origin.

A groundwater management plan for Stuttgart.

PubMed

Vasin, Sandra; Carle, Achim; Lang, Ulrich; Kirchholtes, Hermann Josef

2016-09-01

In general, groundwater in urban areas is exposed to anthropogenic influence and suffers from concentrations of contaminants. Stuttgart, as a highly industrialized city, has more than 5000 contaminated sites which might influence the Stuttgart's mineral water quality. Despite tremendous efforts and intensive single site orientated remediation since 1984 in downtown, the mineral springs were still affected with chlorinated hydrocarbons at low concentrations. Therefore, the applied practices of environmental management and measures for mitigation of pollution sources were not sufficient and had to be adjusted. The main goal of this study is to define an integral remediation plan (a groundwater management plan), focusing on the key sources of chlorinated solvents which are relevant for the mineral springs. For the large-scale investigated area of 26.6km(2) and eight aquifers, an extensive investigation and characterization methods were used in order to delineate the contamination plumes. By means of a 3D numerical model, the prioritization of the contaminated sites could be performed. Five contaminated sites with high remediation priority and need for optimized or additional remediation efforts were determined. For those five contaminated sites feasibility studies were performed which resulted in recommendation of remediation measures with total costs of more than 12.5 million euros. The proposed strategy and approach are suitable for multiple sources of contamination. Only in this way, the contributions of single contaminated sites to the total groundwater contamination can be identified and local remediation measures with their spatial impact simulated. Due to very complex geological conditions, technically there is no alternative to this strategy in order to achieve the contamination reduction in groundwater. Copyright © 2015 Elsevier B.V. All rights reserved.

Chlorinated volatile organic compounds (Cl-VOCs) in environment - sources, potential human health impacts, and current remediation technologies.

PubMed

Huang, Binbin; Lei, Chao; Wei, Chaohai; Zeng, Guangming

2014-10-01

Chlorinated volatile organic compounds (Cl-VOCs), including polychloromethanes, polychloroethanes and polychloroethylenes, are widely used as solvents, degreasing agents and a variety of commercial products. These compounds belong to a group of ubiquitous contaminants that can be found in contaminated soil, air and any kind of fluvial mediums such as groundwater, rivers and lakes. This review presents a summary of the research concerning the production levels and sources of Cl-VOCs, their potential impacts on human health as well as state-of-the-art remediation technologies. Important sources of Cl-VOCs principally include the emissions from industrial processes, the consumption of Cl-VOC-containing products, the disinfection process, as well as improper storage and disposal methods. Human exposure to Cl-VOCs can occur through different routes, including ingestion, inhalation and dermal contact. The toxicological impacts of these compounds have been carefully assessed, and the results demonstrate the potential associations of cancer incidence with exposure to Cl-VOCs. Most Cl-VOCs thus have been listed as priority pollutants by the Ministry of Environmental Protection (MEP) of China, Environmental Protection Agency of the U.S. (U.S. EPA) and European Commission (EC), and are under close monitor and strict control. Yet, more efforts will be put into the epidemiological studies for the risk of human exposure to Cl-VOCs and the exposure level measurements in contaminated sites in the future. State-of-the-art remediation technologies for Cl-VOCs employ non-destructive methods and destructive methods (e.g. thermal incineration, phytoremediation, biodegradation, advanced oxidation processes (AOPs) and reductive dechlorination), whose advantages, drawbacks and future developments are thoroughly discussed in the later sections. Copyright © 2014 Elsevier Ltd. All rights reserved.

Using Iron to Treat Chlorohydrocarbon-Contaminated Soil

NASA Technical Reports Server (NTRS)

Hitchens, G. Duncan; Hodko, Dalibor; Kim, Heekyung; Rogers, Tom; Singh, Waheguru Pal; Giletto, Anthony; Cisar, Alan

2004-01-01

A method of in situ remediation of soil contaminated with chlorinated hydrocarbon solvents involves injection of nanometer-size iron particles. The present method exploits a combination of prompt chemical remediation followed by longer-term enhanced bioremediation and, optionally, is practiced in conjunction with the method of bioremediation described earlier. Newly injected iron particles chemically reduce chlorinated hydrocarbons upon contact. Thereafter, in the presence of groundwater, the particles slowly corrode via chemical reactions that effect sustained release of dissolved hydrogen. The hydrogen serves as an electron donor, increasing the metabolic activity of the anaerobic bacteria and thereby sustaining bioremediation at a rate higher than the natural rate.

A chlorine precursor route (CPR) to poly(p-phenylene vinylene) light emitting diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heieh, B.R.; Antoniadis, H.; Bland, D.C.

1995-12-01

We use a chlorine precursor route (CPR) to fabricate PPV based electroluminescent (EL) devices. 1,4- Bis(chloromethyl)-2,3-diphenylbenzene was polymerized with one equivalent amount of potassium t-butoxide (t-BuOK) to give the corresponding chlorine precursor polymer with very high molecular weights. This polymer is soluble in common organic solvents and is highly stable in the solid state and in solution. Thin films of the precursor polymer were spin cast on indiumtin-oxide (ITO) coated glass substrates followed by thermal conversion at 300{degrees}C for 2 h to give DP-PPV thin films. We found that CPR is more convenient and reliable than sulfonium precursor route formore » the fabrication of PPV thin film EL devices. Efficient emission of green light (500 nm) was observed for Mg/DP-PPV/ITO and Al/DP-PPV/ITO single layer devices.« less

Elucidating the Higher Stability of Vanadium (V) Cations in Mixed Acid Based Redox Flow Battery Electrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vijayakumar, M.; Wang, Wei; Nie, Zimin

2013-11-01

The Vanadium (V) cation structures in mixed acid based electrolyte solution were analysed by density functional theory (DFT) based computational modelling and 51V and 35Cl Nuclear Magnetic Resonance (NMR) spectroscopy. The Vanadium (V) cation exists as di-nuclear [V2O3Cl2.6H2O]2+ compound at higher vanadium concentrations (≥1.75M). In particular, at high temperatures (>295K) this di-nuclear compound undergoes ligand exchange process with nearby solvent chlorine molecule and forms chlorine bonded [V2O3Cl2.6H2O]2+ compound. This chlorine bonded [V2O3Cl2.6H2O]2+ compound might be resistant to the de-protonation reaction which is the initial step in the precipitation reaction in Vanadium based electrolyte solutions. The combined theoretical and experimental approachmore » reveals that formation of chlorine bonded [V2O3Cl2.6H2O]2+ compound might be central to the observed higher thermal stability of mixed acid based Vanadium (V) electrolyte solutions.« less

Hydrogeophysical imaging of deposit heterogeneity and groundwater chemistry changes during DNAPL source zone bioremediation.

PubMed

Chambers, J E; Wilkinson, P B; Wealthall, G P; Loke, M H; Dearden, R; Wilson, R; Allen, D; Ogilvy, R D

2010-10-21

Robust characterization and monitoring of dense nonaqueous phase liquid (DNAPL) source zones is essential for designing effective remediation strategies, and for assessing the efficacy of treatment. In this study high-resolution cross-hole electrical resistivity tomography (ERT) was evaluated as a means of monitoring a field-scale in-situ bioremediation experiment, in which emulsified vegetable oil (EVO) electron donor was injected into a trichloroethene source zone. Baseline ERT scans delineated the geometry of the interface between the contaminated alluvial aquifer and the underlying mudstone bedrock, and also the extent of drilling-induced physical heterogeneity. Time-lapse ERT images revealed major preferential flow pathways in the source and plume zones, which were corroborated by multiple lines of evidence, including geochemical monitoring and hydraulic testing using high density multilevel sampler arrays within the geophysical imaging planes. These pathways were shown to control the spatial distribution of the injected EVO, and a bicarbonate buffer introduced into the cell for pH control. Resistivity signatures were observed within the preferential flow pathways that were consistent with elevated chloride levels, providing tentative evidence from ERT of the biodegradation of chlorinated solvents. Copyright © 2010 S. Yamamoto. Published by Elsevier B.V. All rights reserved.

40 CFR 261.31 - Hazardous wastes from non-specific sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... free radical catalyzed processes. These chlorinated aliphatic hydrocarbons are those having carbon... spent desiccant wastes from the production of certain chlorinated aliphatic hydrocarbons, by free radical catalyzed processes. These chlorinated aliphatic hydrocarbons are those having carbon chain...

40 CFR 261.31 - Hazardous wastes from non-specific sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... free radical catalyzed processes. These chlorinated aliphatic hydrocarbons are those having carbon... spent desiccant wastes from the production of certain chlorinated aliphatic hydrocarbons, by free radical catalyzed processes. These chlorinated aliphatic hydrocarbons are those having carbon chain...

Pilot-Scale Demonstration of In-Situ Chemical Oxidation ...

EPA Pesticide Factsheets

A pilot-scale in situ chemical oxidation (ISCO) demonstration, involving subsurface injections of sodium permanganate (NaMnO4), was performed at the US Marine Corp Recruit Depot (MCRD), site 45 (Parris Island (PI), SC). The ground water was originally contaminated with perchloroethylene (PCE) (also known as tetrachloroethylene), a chlorinated solvent used in dry cleaner operations. High resolution site characterization involved multiple iterations of soil core sampling and analysis. Nested micro-wells and conventional wells were also used to sample and analyze ground water for PCE and decomposition products (i.e., trichloroethyelene (TCE), dichloroethylene (c-DCE, t-DCE), and vinyl chloride (VC)), collectively referred to as chlorinated volatile organic compounds (CVOC). This characterization methodology was used to develop and refine the conceptual site model and the ISCO design, not only by identifying CVOC contamination but also by eliminating uncontaminated portions of the aquifer from further ISCO consideration. Direct-push injection was selected as the main method of NaMnO4 delivery due to its flexibility and low initial capital cost. Site impediments to ISCO activities in the source area involved subsurface utilities, including a high pressure water main, a high voltage power line, a communication line, and sanitary and stormwater sewer lines. Utility markings were used in conjunction with careful planning and judicious selection of injection locations. A

PERFORMANCE ASSESSMENT OF IN-WELL AERATION FOR THE REMEDIATION OF AN AQUIFER CONTAMINATED BY MULTICOMPONENT IMMISCIBLE LIQUID

EPA Science Inventory

A pilot-scale test to evaluate the performance of a vertical recirculation well equipped with an in-well air stripper was conducted at Hill AFB, Utah, in an aquifer contaminated with petroleum and chlorinated solvents. During the two months of operation, the air stripping system ...

Natural Attenuation of Chlorinated Solvent Ground-Water Plumes Discharging into Wetlands

DTIC Science & Technology

2003-09-01

ground water in highly saline wetlands (Swanson et al., 1984), and the distribution of marsh marigold (Caltha palustris L.) has been used to map...seeps and springs next to a lake and in wetlands in Minnesota (Rosenberry et al., 2000). Marsh marigold favors ground-water discharge areas across the

DISTRIBUTION OF DEHALOCCOIDES AT DOD CHLORINATED SOLVENT SITES-DO YOU NEED TO BIOAUGMENT?

EPA Science Inventory

Dehaloccoides is the only organism that has been shown to completely dechlorinate TCE, cis-DCE, and vinyl chloride to ethene or ethane (Maymo-Gatell et al., 2001; He et al., 2003a; He et al., 2003b). Dehaloccoides is a naturally occurring organism, with a world-wide distribution...

Reductive amination with zinc powder in aqueous media

PubMed Central

Imperio, Daniela; Penoni, Andrea; Palmisano, Giovanni

2011-01-01

Summary Zinc powder in aqueous alkaline media was employed to perform reductive amination of aldehydes with primary amines. The corresponding secondary amines were obtained in good yields along with minor amounts of hydrodimerization byproducts. The protocol is a green alternative to the use of complex hydrides in chlorinated or highly flammable solvents. PMID:21915212

ANALYSIS OF A GAS-PHASE PARTITIONING TRACER TEST CONDUCTED IN AN UNSATURATED FRACTURED-CLAY FORMATION

EPA Science Inventory

The gas-phase partitioning tracer method was used to estimate non-aqueous phase liquid (NAPL), water, and air saturations in the vadose zone at a chlorinated-solvent contaminated field site in Tucson, AZ. The tracer test was conducted in a fractured-clay system that is the confin...

Degradation Kinetics of Carbon Tetrachloride by Sulfate Green Rust as Influenced by pH and Copper Ions (Stillwater)

EPA Science Inventory

Chlorinated solvents such as trichloroethene (TCE, C2HCl3) and carbon tetrachloride (CT, CCl4) are priority groundwater contaminants at many EPA field sites. Green rust (GR) minerals are important corrosion products of zerovalent iron (Fe0) that has been used in permeable react...

Degradation Kinetics of Carbon Tetrachloride by Sulfate Green Rust as Influenced by pH and Copper Ions

EPA Science Inventory

Chlorinated solvents such as trichloroethene (TCE, C2HCl3) and carbon tetrachloride (CT, CCl4) are priority groundwater contaminants at many EPA field sites. Green rust (GR) minerals are important corrosion products of zerovalent iron (Fe0) that has been used in permeable reactiv...

Integrated Stable Isotope - Reactive Transport Model Approach for Assessment of Chlorinated Solvent Degradation

DTIC Science & Technology

2016-06-16

immediate electron donor. In the microcosm, H2 was produced by fermentation of lactate. It was previously reported that H2 and water undergo fast...being tied to the H isotope composition of the fermentation substrate (see Kuder et al., 2013 for more information). ESTCP Final Report

New Developments in 1,4 Dioxane Site Management

DTIC Science & Technology

2016-11-01

oxidation, enhanced bioremediation , site management. Unclassified Unclassified UU UL 8 David Adamson (713) 522-6300 Page Intentionally Left Blank...there was little indication that chlorinated solvent remedial efforts (e.g., chemical oxidation, enhanced bioremediation ) impacted 1,4-dioxane...oxidation may prove beneficial for subsequent biologically- based approaches, including both enhanced bioremediation and natural attenuation. FOR

Application of Microarrays and qPCR to Identify Phylogenetic and Functional Biomarkers Diagnostic of Microbial Communities that Biodegrade Chlorinated Solvents to Ethene

DTIC Science & Technology

2012-01-01

Acidobacteria, Actinobacteria , Bacteroidetes, Chloroflexi, Cyanobacteria, Firmicutes, and all classes of Proteobacteria accounted for 76% of this dynamic...the course of treatment (Figure 4). The dominant members in cluster group 2 were from Actinobacteria (24 subfamilies), Bacteroidetes (25 subfamilies

In planta passive sampling devices for assessing subsurface chlorinated solvents.

PubMed

Shetty, Mikhil K; Limmer, Matt A; Waltermire, Kendra; Morrison, Glenn C; Burken, Joel G

2014-06-01

Contaminant concentrations in trees have been used to delineate groundwater contaminant plumes (i.e., phytoscreening); however, variability in tree composition hinders accurate measurement of contaminant concentrations in planta, particularly for long-term monitoring. This study investigated in planta passive sampling devices (PSDs), termed solid phase samplers (SPSs) to be used as a surrogate tree core. Characteristics studied for five materials included material-air partitioning coefficients (Kma) for chlorinated solvents, sampler equilibration time and field suitability. The materials investigated were polydimethylsiloxane (PDMS), low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), polyoxymethylene (POM) and plasticized polyvinyl chloride (PVC). Both PDMS and LLDPE samplers demonstrated high partitioning coefficients and diffusivities and were further tested in greenhouse experiments and field trials. While most of the materials could be used for passive sampling, the PDMS SPSs performed best as an in planta sampler. Such a sampler was able to accurately measure trichloroethylene (TCE) and tetrachloroethylene (PCE) concentrations while simultaneously incorporating simple operation and minimal impact to the surrounding property and environment. Copyright © 2013 Elsevier Ltd. All rights reserved.

Vapor-phase exchange of perchloroethene between soil and plants

USGS Publications Warehouse

Struckhoff, G.C.; Burken, J.G.; Schumacher, J.G.

2005-01-01

Tree core concentrations of tetrachloroethylene (perchloroethene, PCE) at the Riverfront Superfund Site in New Haven, MO, were found to mimic the profile of soil phase concentrations. The observed soil-tree core relationship was stronger than that of groundwater PCE to tree core concentrations at the same site. Earlier research has shown a direct, linear relationship between tree core and groundwater concentrations of chlorinated solvents and other organics. Laboratory-scale experiments were performed to elucidate this phenomenon, including determining partitioning coefficients of PCE between plant tissues and air and between plant tissues and water, measured to be 8.1 and 49 L/kg, respectively. The direct relationship of soil to tree core PCE concentrations was hypothesized to be caused by diffusion between tree roots and the soil vapor phase in the subsurface. The central findings of this research are discovering the importance of subsurface vapor-phase transfer for VOCs and uncovering a direct relationship between soil vapor-phase chlorinated solvents and uptake rates that impact contaminant translocation from the subsurface and transfer into the atmosphere. ?? 2005 American Chemical Society.

Treatment of Chlorinated Solvents in Groundwater Beneath an Occupied Building at the Young-Rainey STAR Center, Pinellas, FL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, Joe; Surovchak, Scott; Tabor, Charles

Groundwater contamination, consisting of two dissolved-phase plumes originating from chlorinated solvent source areas, in the southeastern portion of the Young- Rainey Star Center (also known as the Pinellas County, Florida, Site) in Largo, Florida, has migrated beyond the property boundary, beneath the roadways, and beneath adjacent properties to the south and east. Groundwater contamination will persist as long as the onsite contaminant source remains. The origin of the contamination appears to be multiple long-term point sources beneath Building 100, a 4.5 ha (11 acre) building that housed manufacturing facilities during US DOE operations at the site. The site is nowmore » owned by Pinellas County, and most of the space inside the building is leased to private companies, so DOE chose not to conduct characterization or remediation through the floor of the building, instead choosing to conduct all work from outside the building. Injection of emulsified soybean oil and a microbial culture has been used at other areas of the site to accelerate naturally occurring bacterial processes that degrade groundwater contaminants to harmless compounds, and that same approach was chosen for this task. The technical approach consisted of installing horizontal wells from outside the building footprint, extending through and around the identified subsurface treatment areas, and terminating beneath the building. Two 107 m (350 ft) long wells, two 122 m (400 ft) long wells, and four 137 m (450 ft) long wells have been installed to intersect the inferred source areas and confirmed contaminant plumes beneath the building. DOE then injected emulsified vegetable oil and a microbial culture into the horizontal wells at each of several target areas beneath the building where the highest groundwater contaminant concentrations have been detected. The target areas are the northwest corner of the building between the old drum storage pad locations and monitoring well PIN12-S35B, the vicinity of former monitoring well PIN12-S57B, and hydraulically upgradient from the south plume and the east plume at the points where they exit from beneath the building. We describe the details of designing and constructing horizontal injection wells for bioremediation beneath a large, occupied industrial production facility, including lessons learned; technical, logistical, and environmental challenges; community relations; and regulatory relations. Because of the expected lag in biological acclimation and response, distance between the treatment areas and associated monitoring points, and low groundwater velocity, it will likely be years before the full impact of the project will be realized.« less

Health assessment for Pasley Solvents and Chemical, Garden City, New York, Region 2. CERCLIS No. NYD991292004. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-06-01

The Pasley Solvents and Chemicals site, a National Priorities List site, is located in the Town of Hempstead, immediately east of the Village of Garden City in Nassau County, New York. Between 1969 and 1982, Pasley operated a chemical distribution facility on the lot, occasionally storing waste chemicals. Prior to this, Commander Oil used the site for gasoline storage and fuel oil distribution. The Nassau County Health Department (NCHD) investigated the site in 1981 and found the on-site soil and ground water to be contaminated with organic solvents and petroleum products. On-site sampling by NCHD and the owner has revealedmore » organic chemicals and petroleum products in both soil and ground water. Six chlorinated solvents and four aromatic compounds are in ground water above the part per million. The site is a potential threat to public health.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Exon, J.H.

The chlorinated phenols are a group of 19 isomers composed of phenol with substituted chlorines. These chemicals are readily soluble in organic solvents but only slightly soluble in water, except for the chlorophenate salts. Chlorophenols with less than 3 chlorines are not used extensively except in the production of higher chlorophenols and chlorophenyloxyacetic acid herbicides. Pentachlorophenol and some tetrachlorophenols are used worldwide, primarily as wood preservatives or fungicides. Residues of chlorophenols have been found worldwide in soil, water and air samples, in food products, and in human and animal tissues and body fluids. Environmental contamination with these chemicals occurs frommore » industrial effluents, agricultural runoff, breakdown of chlorophenyloxyacetic acid herbicides and hexachlorobenzene, and from spontaneous formation following chlorination of water for disinfection and deodorization. The acute toxicity of these chemicals is relatively low and little is known concerning their chronic effects. Chlorophenols have not been shown conclusively to be mutagens, teratogens or carcinogens. However, these compounds may act as promotors or cocarcinogens and the immune system is particularly sensitive to their toxic effects. Transplacental exposure to chlorophenols may result in embryotoxicity and abortion. The major mode of toxic action is as uncouplers of oxidative phosphorylation. The toxicity of chlorophenols decreases with decreasing chlorination. These chemicals are mild hepatotoxins and are stored mainly in hepatic and renal tissues.« less

STABLE CHLORINE ISOTOPE ANALYSIS OF CHLORINATED ORGANIC CONTAMINANTS

EPA Science Inventory

The biogeochemical cycling of chlorinated organic contaminants in the environment is often difficult to understand because of the complex distributions of these compounds and variability of sources. To address these issues from an isotopic perspective, we have measured the, 37Cl...

Chlorine isotope geochemistry of Icelandic thermal fluids: Implications for geothermal system behavior at divergent plate boundaries

NASA Astrophysics Data System (ADS)

Stefánsson, Andri; Barnes, Jaime D.

2016-09-01

The chlorine isotope composition of thermal fluids from Iceland were measured in order to evaluate the source of chlorine and possible chlorine isotope fractionation in geothermal systems at divergent plate boundaries. The geothermal systems studied have a wide range of reservoir temperatures from 40 to 437 °C and in-situ pH of 6.15 to 7.15. Chlorine concentrations range from 5.2 to 171 ppm and δ37 Cl values are -0.3 to + 2.1 ‰ (n = 38). The δ37 Cl values of the thermal fluids are interpreted to reflect the source of the chlorine in the fluids. Geothermal processes such as secondary mineral formation, aqueous and vapor speciation and boiling were found to have minimal effects on the δ37 Cl values. However, further work is needed on incorporation of Cl into secondary minerals and its effect on Cl isotope fractionation. Results of isotope geochemical modeling demonstrate that the range of δ37 Cl values documented in the natural thermal fluids can be explained by leaching of the basaltic rocks by meteoric source water under geothermal conditions. Magmatic gas partitioning may also contribute to the source of Cl in some cases. The range of δ37 Cl values of the fluids result mainly from the large range of δ37 Cl values observed for Icelandic basalts, which range from -0.6 to + 1.2 ‰.

A comparison of various modes of liquid-liquid based microextraction techniques: determination of picric acid.

PubMed

Burdel, Martin; Šandrejová, Jana; Balogh, Ioseph S; Vishnikin, Andriy; Andruch, Vasil

2013-03-01

Three modes of liquid-liquid based microextraction techniques--namely auxiliary solvent-assisted dispersive liquid-liquid microextraction, auxiliary solvent-assisted dispersive liquid-liquid microextraction with low-solvent consumption, and ultrasound-assisted emulsification microextraction--were compared. Picric acid was used as the model analyte. The determination is based on the reaction of picric acid with Astra Phloxine reagent to produce an ion associate easily extractable by various organic solvents, followed by spectrophotometric detection at 558 nm. Each of the compared procedures has both advantages and disadvantages. The main benefit of ultrasound-assisted emulsification microextraction is that no hazardous chlorinated extraction solvents and no dispersive solvent are necessary. Therefore, this procedure was selected for validation. Under optimized experimental conditions (pH 3, 7 × 10(-5) mol/L of Astra Phloxine, and 100 μL of toluene), the calibration plot was linear in the range of 0.02-0.14 mg/L and the LOD was 7 μg/L of picric acid. The developed procedure was applied to the analysis of spiked water samples. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Solutions Remediate Contaminated Groundwater

NASA Technical Reports Server (NTRS)

2010-01-01

During the Apollo Program, NASA workers used chlorinated solvents to clean rocket engine components at launch sites. These solvents, known as dense non-aqueous phase liquids, had contaminated launch facilities to the point of near-irreparability. Dr. Jacqueline Quinn and Dr. Kathleen Brooks Loftin of Kennedy Space Center partnered with researchers from the University of Central Florida's chemistry and engineering programs to develop technology capable of remediating the area without great cost or further environmental damage. They called the new invention Emulsified Zero-Valent Iron (EZVI). The groundwater remediation compound is cleaning up polluted areas all around the world and is, to date, NASA's most licensed technology.

Chemically modified graphite for electrochemical cells

DOEpatents

Greinke, R.A.; Lewis, I.C.

1998-05-26

This invention relates to chemically modified graphite particles: (a) that are useful in alkali metal-containing electrode of a electrochemical cell comprising: (1) the electrode, (2) a non-aqueous electrolytic solution comprising an organic aprotic solvent which solvent tends to decompose when the electrochemical cell is in use, and an electrically conductive salt of an alkali metal, and (3) a counter electrode; and (b) that are chemically modified with fluorine, chlorine, iodine or phosphorus to reduce such decomposition. This invention also relates to electrodes comprising such chemically modified graphite and a binder and to electrochemical cells containing such electrodes. 3 figs.

Chemically modified graphite for electrochemical cells

DOEpatents

Greinke, Ronald Alfred; Lewis, Irwin Charles

1998-01-01

This invention relates to chemically modified graphite particles: (a) that are useful in alkali metal-containing electrode of a electrochemical cell comprising: (i) the electrode, (ii) a non-aqueous electrolytic solution comprising an organic aprotic solvent which solvent tends to decompose when the electrochemical cell is in use, and an electrically conductive salt of an alkali metal, and (iii) a counterelectrode; and (b) that are chemically modified with fluorine, chlorine, iodine or phosphorus to reduce such decomposition. This invention also relates to electrodes comprising such chemically modified graphite and a binder and to electrochemical cells containing such electrodes.

Efficient dechlorination of chlorinated solvent pollutants under UV irradiation by using the synthesized TiO2 nano-sheets in aqueous phase.

PubMed

Ndong, Landry Biyoghe Bi; Ibondou, Murielle Primaelle; Miao, Zhouwei; Gu, Xiaogang; Lu, Shuguang; Qiu, Zhaofu; Sui, Qian; Mbadinga, Serge Maurice

2014-05-01

Titanium dioxide (TiO2), which is the widely used photo-catalyst, has been synthesized by simple hydrothermal solution containing tetrabutyl titanate and hydrofluoric acid. The synthesized product has been applied to photo-degradation in aqueous phase of chlorinated solvents, namely tetrachloroethene (PCE), trichloroethene (TCE) and 1,1,1-trichloroethane (TCA). The photo-degradation results revealed that the degradation of these harmful chemicals was better in UV/synthesized TiO2 system compared to UV/commercial P25 system and UV only system. The photo-catalytic efficiency of the synthesized TiO2 was 1.4, 1.8 and 3.0 folds higher compared to the commercial P25 for TCA, TCE and PCE degradation, respectively. Moreover, using nitrobenzene (NB) as a probe of hydroxyl radical (·OH), the degradation rate was better over UV/synthesized TiO2, suggesting the high concentration of ·OH generated in UV/synthesized TiO2 system. In addition, ·OH concentration was confirmed by the strong peak displayed in EPR analysis over UV/synthesized TiO2 system. The characterization result using XRD and TEM showed that the synthesized TiO2 was in anatase form and consisted of well-defined sheet-shaped structures having a rectangular outline with a thickness of 4 nm, side length of 50 nm and width of 33 nm and a surface 90.3 m(2)/g. XPS analysis revealed that ≡Ti-F bond was formed on the surface of the synthesized TiO2. The above results on both photocatalytic activity and the surface analysis demonstrated the good applicability of the synthesized TiO2 nano-sheets for the remediation of chlorinated solvent contaminated groundwater. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Vegetation sampling for the screening of subsurface pollution

NASA Astrophysics Data System (ADS)

Karlson, U. G.; Petersen, M. D.; Algreen, M.; Rein, A.; Sheehan, E.; Limmer, M. A.; Burken, J. G.; Mayer, P.; Trapp, S.

2012-04-01

Measurement of vegetation samples has been reported as an alternative, cheap method to drilling for exploring subsurface pollution. The purpose of this presentation is to give an update on some further developments of this field method - faster sampling and improved analysis for chlorinated solvents, and application of phytomonitoring to heavy metal contamination. Rapid analysis of trees for chlorinated solvents was facilitated by employing automated headspace SPME-GC/ECD, resulting in a detection limit of 0.87 and 0.04 μg/kg fresh weight of wood for TCE and PCE, respectively, which is significantly lower than we have reported earlier, using manual injection of 1mL headspace air into a GC/MS. Technical details of the new method will be presented. As an even more direct alternative, time weighted average SPME analysis has been developed for in planta sampling of trees, using novel polydimethylsiloxane/carboxen SPME fibres designed for field application. In a different study, trees growing on a former dump site in Norway were analyzed for arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), and zinc (Zn). Concentrations in wood were in averages (dw) 30 mg/kg for Zn, 2 mg/kg for Cu, and <1 mg/kg for Cd, Cr, As and Ni. For all except one case, mean concentrations from the dump site were higher than those from a unpolluted reference site, but the difference was small and not always significant. Differences between tree species were typically higher than differences between the polluted and the unpolluted site. As all these elements occur naturally, and Cu, Ni, and Zn are essential elements, all trees will have a natural background of these elements, and the occurrence alone does not indicate soil pollution. For the interpretation of the results, a comparison to wood samples from an unpolluted reference site with the same tree species and similar soil conditions is required. This makes the tree core screening method less reliable for heavy metals than, e.g., for chlorinated solvents.

Reductive Outer-Sphere Single Electron Transfer Is an Exception Rather than the Rule in Natural and Engineered Chlorinated Ethene Dehalogenation.

PubMed

Heckel, Benjamin; Cretnik, Stefan; Kliegman, Sarah; Shouakar-Stash, Orfan; McNeill, Kristopher; Elsner, Martin

2017-09-05

Chlorinated ethenes (CEs) such as perchloroethylene, trichloroethylene and dichloroethylene are notorious groundwater contaminants. Although reductive dehalogenation is key to their environmental and engineered degradation, underlying reaction mechanisms remain elusive. Outer-sphere reductive single electron transfer (OS-SET) has been proposed for such different processes as Vitamin B 12 -dependent biodegradation and zerovalent metal-mediated dehalogenation. Compound-specific isotope effect ( 13 C/ 12 C, 37 Cl/ 35 Cl) analysis offers a new opportunity to test these hypotheses. Defined OS-SET model reactants (CO 2 radical anions, S 2- -doped graphene oxide in water) caused strong carbon (ε C = -7.9‰ to -11.9‰), but negligible chlorine isotope effects (ε Cl = -0.12‰ to 0.04‰) in CEs. Greater chlorine isotope effects were observed in CHCl 3 (ε C = -7.7‰, ε Cl = -2.6‰), and in CEs when the exergonicity of C-Cl bond cleavage was reduced in an organic solvent (reaction with arene radical anions in glyme). Together, this points to dissociative OS-SET (SET to a σ* orbital concerted with C-Cl breakage) in alkanes compared to stepwise OS-SET (SET to a π* orbital followed by C-Cl cleavage) in ethenes. The nonexistent chlorine isotope effects of chlorinated ethenes in all aqueous OS-SET experiments contrast strongly with pronounced Cl isotope fractionation in all natural and engineered reductive dehalogenations reported to date suggesting that OS-SET is an exception rather than the rule in environmental transformations of chlorinated ethenes.

Occurrence of Sustained Treatment Following Enhanced Anaerobic Bioremediation at Chlorinated Solvent Sites

NASA Astrophysics Data System (ADS)

Burcham, M.; Bedient, P.; McGuire, T.; Adamson, D.; Newell, C. J.

2012-12-01

Chlorinated solvents are among the most prevalent groundwater contaminants found in the United States, located at nearly 80% of all Superfund sites, and at more than 3,000 Department of Defense sites. Responsible parties in the U.S. spend several billion dollars per year on environmental restoration with much of these funds targeting remediation of chlorinated solvents in groundwater. To make this large investment in groundwater remediation technologies more effective, end-users need quantitative, accurate, and reliable performance data for commonly used remediation technologies. One such technology that has been used increasingly for remediation of chlorinated solvent sites is enhanced anaerobic bioremediation (EAB). A previous study of remediation performance of various technologies indicated that EAB has the potential for sustained treatment several years after injection of an EAB substrate. This benefit is attributed to the recycling of decaying biomass (endogenous decay) and/or the formation of reactive mineral species, and it serves to mitigate the incidence of concentration rebound during the post-treatment period that is commonly-observed with other technologies. The current study expands on the previous study by focusing on the occurrence of sustained treatment at EAB sites through analysis of groundwater concentration data for longer post-treatment periods than were available for the previous study (up to 9 years), along with site characteristics such as hydrogeology, geochemistry, and microbiology. The objective is to determine whether relationships exist that can aid in determining when sustained treatment following EAB might occur for a given site. To date, data from over 17 distinct sites applying EAB have been collected. The dataset includes over 50 monitoring wells within EAB treatment zones, with concentration data extending from before treatment began to more than 3 to 9 years following treatment. Efforts are underway to continue this data mining effort and expand the number of sites. The occurrence of sustained treatment is evaluated using several metrics, including: i) concentration reduction achieved over the post-treatment monitoring period; ii) concentration trend analysis over the post-treatment monitoring period using the Mann-Kendall statistical procedure; iii) comparison of decay rates from before and after treatment; and iv) the occurrence of concentration rebound. Of the 17 sites evaluated to date, sustained treatment appears to be occurring at 11 sites (65%), as evidenced by sustained reductions in post-treatment groundwater concentrations. At sites where sustained treatment appears to be occurring, site characteristics such as predominant aquifer soil type, groundwater flow rate, groundwater geochemistry, presence of native dechlorinating bacteria, etc. will be evaluated to determine if relationships exist between these properties and the occurrence of sustained treatment.

Methylated silicates may explain the release of chlorinated methane from Martian soil

NASA Astrophysics Data System (ADS)

Bak, Ebbe N.; Jensen, Svend J. Knak; Nørnberg, Per; Finster, Kai

2016-01-01

The only organic compounds that have been detected in the Martian soil are simple chlorinated compounds released from heated surface material. However, the sources of the organic carbon are in dispute. Wind abraded silicates, which are widespread on the Martian surface, can sequester atmospheric methane which generates methylated silicates and thus could provide a mechanism for accumulation of reduced carbon in the surface soil. In this study we show that thermal volatilization of methylated silicates in the presence of perchlorate leads to the production of chlorinated methane. Thus, methylated silicates could be a source of the organic carbon released as chlorinated methane upon thermal volatilization of Martian soil samples. Further, our experiments show that the ratio of the different chlorinated compounds produced is dependent on the mass ratio of perchlorate to organic carbon in the soil.

Valiant 'Zero-Valent' Effort Restores Contaminated Grounds

NASA Technical Reports Server (NTRS)

2005-01-01

Dense non-aqueous phase liquids (DNAPLs) are chemical compounds that can contaminate soil and groundwater to the point of irreparability. These substances are only slightly soluble in water, and are much denser than water. Because of their solubility, DNAPLs form separate liquid phases in groundwater, and because of their density, DNAPLs sink in aquifers instead of floating at the water table, making it extremely difficult to detect their presence. If left untreated in the ground, they can taint fresh water sources. Common DNAPLs include chlorinated hydrocarbon compounds such as carbon tetrachloride, chloroform, tetrachloroethylene, and trichloroethylene. Trichloroethylene was used during the early days of the Space Program, as a solvent for flushing rocket engines, and for metal cleaning and degreasing of equipment, electronics, and heavy machinery. As a result, areas of Cape Canaveral s Launch Complex 34, the site of several historic Saturn rocket launches occurring from 1959 to 1968, were polluted with chlorinated DNAPLs. Through the direction and guidance of Dr. Jacqueline Quinn, an environmental engineer in the Spaceport Engineering and Technology Directorate at NASA s Kennedy Space Center, a biodegradable environmental cleanup technology was developed to reductively dechlorinate DNAPL sources in polluted water at Launch Complex 34. It was important for Kennedy to nip this problem in the bud, in light of the fact that the Space Center is also a National Wildlife Refuge, home to thousands of shorebirds, endangered sea turtles and eagles, manatees, alligators, and diverse habitats that include brackish marshes and salt water estuaries. The success in remediating this historic launch site has led to numerous commercial applications that are restoring the health of our environmental surroundings.

CHARACTERIZATION OF CHLORINATION TRANSFORMATION PRODUCTS OF SELECTED PESTICIDES

EPA Science Inventory

Chlorination is a commonly-used disinfectant step in drinking water treatment. Should free chlorine be added to water used as a drinking water source, it is widely understood that many biological species in the water along with dissolved organic and inorganic chemicals will react...

Influence of Nitrogen Source on NDMA Formation during Chlorination of Diuron

PubMed Central

Chen, Wei-Hsiang; Young, Thomas M.

2009-01-01

N-Nitrosodimethylamine (NDMA) is formed during chlorination of water containing the herbicide diuron (N′-(3,4-dichlorophenyl)-N, N-dimethylurea) but formation is greatly enhanced in the presence of ammonia (chloramination). Groundwater impacted by agricultural runoff may contain diuron and relatively high total nitrogen concentrations; this study examines the impact of the nitrogen form (ammonium, nitrite or nitrate) on NDMA formation during chlorination of such waters. NDMA formation during chlorination of diuron increased in the order nitrite < nitrate < ammonium for a given chlorine, nitrogen, and diuron dose. Formation of dichloramine seemed to fully explain enhanced NDMA formation in the presence of ammonium. Nitrate unexpectedly enhanced nitrosation of diuron derivatives to form NDMA compared to the cases of no added nitrogen or nitrite addition. Nitrite addition is less effective because it consumes more chlorine and produces intermediates that react rapidly with diuron and its aromatic byproducts. Differences between surface and groundwater in nitrogen forms and concentrations and disinfection approaches, suggest strategies to reduce NDMA formation should vary with drinking water source. PMID:19457535

Influence of nitrogen source on NDMA formation during chlorination of diuron.

PubMed

Chen, Wei-Hsiang; Young, Thomas M

2009-07-01

N-Nitrosodimethylamine (NDMA) is formed during chlorination of water containing the herbicide diuron (N'-(3,4-dichlorophenyl)-N,N-dimethylurea) but formation is greatly enhanced in the presence of ammonia (chloramination). Groundwater impacted by agricultural runoff may contain diuron and relatively high total nitrogen concentrations; this study examines the impact of the nitrogen form (ammonium, nitrite or nitrate) on NDMA formation during chlorination of such waters. NDMA formation during chlorination of diuron increased in the order nitrite

Technology summary of the in situ bioremediation demonstration (methane biostimulation) via horizontal wells at the Savannah River Site Integrated Demonstration Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hazen, T.C.; Looney, B.B.; Fliermans, C.B.

1994-06-01

The US Department of Energy, Office of Technology Development, has been sponsoring full-scale environmental restoration technology demonstrations for the past 4 years. The Savannah River Site Integrated Demonstration focuses on ``Clean-up of Soils ad Groundwater Contaminated with Chlorinated VOCs.`` Several laboratories including our own had demonstrated the ability of methanotrophic bacteria to completely degrade or mineralize chlorinated solvents, and these bacteria were naturally found in soil and aquifer material. Thus the test consisted of injection of methane mixed with air into the contaminated aquifer via a horizontal well and extraction from the vadose zone via a parallel horizontal well.

Two-chamber configuration of Bio-Nano electron cyclotron resonance ion source for fullerene modification.

PubMed

Uchida, T; Rácz, R; Muramatsu, M; Kato, Y; Kitagawa, A; Biri, S; Yoshida, Y

2016-02-01

We report on the modification of fullerenes with iron and chlorine using two individually controllable plasmas in the Bio-Nano electron cyclotron resonance ion source (ECRIS). One of the plasmas is composed of fullerene and the other one is composed of iron and chlorine. The online ion beam analysis allows one to investigate the rate of the vapor-phase collisional modification process in the ECRIS, while the offline analyses (e.g., liquid chromatography-mass spectrometry) of the materials deposited on the plasma chamber can give information on the surface-type process. Both analytical methods show the presence of modified fullerenes such as fullerene-chlorine, fullerene-iron, and fullerene-chlorine-iron.

Dendrochemistry of multiple releases of chlorinated solvents at a former industrial site

Treesearch

Jean Christophe ​Balouet; Joel G. Burken; Frank Karg; Don Vroblesky; Kevin T. Smith; Håkan Grudd; Anders Rindby; François Beaujard; Michel Chalot

2012-01-01

Trees can take up and assimilate contaminants from soil, subsurface, and groundwater. Contaminants in the transpiration stream can become bound or incorporated into the annual rings formed in trees of the temperate zones. The chemical analysis of precisely dated tree rings, called dendrochemistry, can be used to interpret past plant interactions with contaminants. This...

Characterization of Chlorinated Solvent Degradation in a Constructed Wetland

DTIC Science & Technology

2003-03-25

the flows to be different under the same pressure. A 30m Restek RTX- VRX (Model 49314) column was connected to the micro-Electron Capture Detector...min) 2.00 Gas Type: Helium Column 1 (Restek 49314 RTX- VRX ) Column 2 (J&W 113-4332 GS-GASPRO) Max Temp (deg C) 260 Max Temp (deg C

LONG-TERM PERFORMANCE MONITORING FOR A PERMEABLE REACTIVE BARRIER AT THE U.S. COAST GUARD SUPPORT CENTER, ELIZABETH CITY, NORTH CAROLINA

EPA Science Inventory

A continuous hanging iron wall was installed in June, 1996, at the U.S. Coast Guard (USCG) Support Center near Elizabeth City, NC, United States, to treat overlapping plumes of chromate and chlorinated solvent compounds. The wall was emplaced using a continuous trenching machine...

Risk of lung cancer associated with six types of chlorinated solvents: results from two case-control studies in Montreal, Canada

EPA Science Inventory

Methods: Two case-control studies of occupation and lung cancer were conducted in Montreal, including 2,016 cases and 2,001 population controls. Occupational exposure to a host of agents was evaluated using a combination of subject-reported job history and expert assessment. We e...

CONCENTRATION OF TETRACHLOROETHYLENE IN INDOOR AIR AT A FORMER DRY CLEANER FACILITY AS A FUNCTION OF SUBSURFACE CONTAMINATION: A CASE STUDY

EPA Science Inventory

A field study was performed to evaluate indoor air concentrations and vapor intrusion (VI) of tetrachloroethylene (PCE) and other chlorinated solvents at a commercial retail site in Dallas, TX. The building is approximately 40 years old and once housed a dry cleaning operation. R...

MNA of Chlorinated Solvents and Fuel Oxygenates: Why it occurs, how it evolved, and using stable carbon isotopes to predict plume behavior

EPA Science Inventory

The organisms that degrade MTBE under anaerobic conditions are evolved to acquire energy for growth by using molecular hydrogen and carbonate ion to cleave methyl ether bonds. Methyl ether bonds are common in nature and the bond also occurs in MTBE. MTBE in contaminated ground...

Integrating Stable Isotope - Reactive Transport Model Approach for Assessment of Chlorinated Solvent Degradation

DTIC Science & Technology

2016-06-01

Dehalococcoides species require molecular hydrogen as the immediate electron donor. In the microcosm, H2 was produced by fermentation of lactate. It was...superimposed depletion upon H2/H2O equilibrium rather than being tied to the H isotope composition of the fermentation substrate (see Kuder et al., 2013 for more

Rapid analysis of chlorinated anilines in environmental water samples using ultrasound assisted emulsification microextraction with solidification of floating organic droplet followed by HPLC-UV detection.

PubMed

Ramkumar, Abilasha; Ponnusamy, Vinoth Kumar; Jen, Jen-Fon

2012-08-15

The present study demonstrates a simple, rapid and efficient method for the determination of chlorinated anilines (CAs) in environmental water samples using ultrasonication assisted emulsification microextraction technique based on solidification of floating organic droplet (USAEME-SFO) coupled with high performance liquid chromatography-ultraviolet (HPLC-UV) detection. In this extraction method, 1-dodecanol was used as extraction solvent which is of lower density than water, low toxicity, low volatility, and low melting point (24 °C). After the USAEME, extraction solvent could be collected easily by keeping the extraction tube in ice bath for 2 min and the solidified organic droplet was scooped out using a spatula and transferred to another glass vial and allowed to thaw. Then, 10 μL of extraction solvent was diluted with mobile phase (1:1) and taken for HPLC-UV analysis. Parameters influencing the extraction efficiency, such as the kind and volume of extraction solvent, volume of sample, ultrasonication time, pH and salt concentration were thoroughly examined and optimized. Under the optimal conditions, the method showed good linearity in the concentration range of 0.05-500 ng mL(-1) with correlation coefficients ranging from 0.9948 to 0.9957 for the three target CAs. The limit of detection based on signal to noise ratio of 3 ranged from 0.01 to 0.1 ng mL(-1). The relative standard deviations (RSDs) varied from 2.1 to 6.1% (n=3) and the enrichment factors ranged from 44 to 124. The proposed method has also been successfully applied to analyze real water samples and the relative recoveries of environmental water samples ranged from 81.1 to 116.9%. Copyright © 2012 Elsevier B.V. All rights reserved.

Computational insights into the photocyclization of diclofenac in solution: effects of halogen and hydrogen bonding.

PubMed

Bani-Yaseen, Abdulilah Dawoud

2016-08-21

The effects of noncovalent interactions, namely halogen and hydrogen bonding, on the photochemical conversion of the photosensitizing drug diclofenac (DCF) in solution were investigated computationally. Both explicit and implicit solvent effects were qualitatively and quantitatively assessed employing the DFT/6-31+G(d) and SQM(PM7) levels of theory. Full geometry optimizations were performed in solution for the reactant DCF, hypothesized radical-based intermediates, and the main product at both levels of theories. Notably, in good agreement with previous experimental results concerning the intermolecular halogen bonding of DCF, the SQM(PM7) method revealed different values for d(ClO, Å) and ∠(C-ClO, °) for the two chlorine-substituents of DCF, with values of 2.63 Å/162° and 3.13 Å/142° for the trans and cis orientations, respectively. Employing the DFT/6-31+G(d) method with implicit solvent effects was not conclusive; however, explicit solvent effects confirmed the key contribution of hydrogen and halogen bonding in stabilizing/destabilizing the reactant and hypothesized intermediates. Interestingly, the obtained results revealed that a protic solvent such as water can increase the rate of photocyclization of DCF not only through hydrogen bonding effects, but also through halogen bonding. Furthermore, the atomic charges of atoms majorly involved in the photocyclization of DCF were calculated using different methods, namely Mulliken, Hirshfeld, and natural bond orbital (NBO). The obtained results revealed that in all cases there is a notable nonequivalency in the noncovalent intermolecular interactions of the two chlorine substituents of DCF and the radical intermediates with the solvent, which in turn may account for the discrepancy of their reactivity in different media. These computational results provide insight into the importance of halogen and hydrogen bonding throughout the progression of the photochemical conversion of DCF in solution.

ATRAZOME CHLORINATION TRANSFORMATION PRODUCTS UNDER DRINKING WATER DISTRIBUTION SYSTEM CONDITIONS

EPA Science Inventory

Chlorination is a commonly-used disinfectant step in drinking water treatment. Should free chlorine be added to water used as a drinking water source, it is widely understood that many biological species in the water, along with dissolved organic and inorganic chemicals, will rea...

Recovery and diversity of heterotrophic bacteria from chlorinated drinking waters.

PubMed Central

Maki, J S; LaCroix, S J; Hopkins, B S; Staley, J T

1986-01-01

Heterotrophic bacteria were enumerated from the Seattle drinking water catchment basins and distribution system. The highest bacterial recoveries were obtained by using a very dilute medium containing 0.01% peptone as the primary carbon source. Other factors favoring high recovery were the use of incubation temperatures close to that of the habitat and an extended incubation (28 days or longer provided the highest counts). Total bacterial counts were determined by using acridine orange staining. With one exception, all acridine orange counts in chlorinated samples were lower than those in prechlorinated reservoir water, indicating that chlorination often reduces the number of acridine orange-detectable bacteria. Source waters had higher diversity index values than did samples examined following chlorination and storage in reservoirs. Shannon index values based upon colony morphology were in excess of 4.0 for prechlorinated source waters, whereas the values for final chlorinated tap waters were lower than 2.9. It is not known whether the reduction in diversity was due solely to chlorination or in part to other factors in the water treatment and distribution system. Based upon the results of this investigation, we provide a list of recommendations for changes in the procedures used for the enumeration of heterotrophic bacteria from drinking waters. Images PMID:3524453

Electrochemistry of Interhalogen Cathodes

DTIC Science & Technology

sources. Chlorine trifluoride , with a theoretical 2120 whr/lb in combination with lithium, is also known to support substantial current densities when... chlorine trifluoride as a power source cathode material. A half-cell study was made on dilute ClF3 solutions at 5C in 1 M NaF-HF by the cyclic

Impact of bromide on halogen incorporation into organic moieties in chlorinated drinking water treatment and distribution systems.

PubMed

Tan, J; Allard, S; Gruchlik, Y; McDonald, S; Joll, C A; Heitz, A

2016-01-15

The impact of elevated bromide concentrations (399 to 750 μg/L) on the formation of halogenated disinfection by-products (DBPs), namely trihalomethanes, haloacetic acids, haloacetonitriles, and adsorbable organic halogen (AOX), in two drinking water systems was investigated. Bromine was the main halogen incorporated into all of the DBP classes and into organic carbon, even though chlorine was present in large excess to maintain a disinfectant residual. Due to the higher reactivity of bromine compared to chlorine, brominated DBPs were rapidly formed, followed by a slower increase in chlorinated DBPs. Higher bromine substitution and incorporation factors for individual DBP classes were observed for the chlorinated water from the groundwater source (lower concentration of dissolved organic carbon (DOC)), which contained a higher concentration of bromide, than for the surface water source (higher DOC). The molar distribution of adsorbable organic bromine to chlorine (AOBr/AOCl) for AOX in the groundwater distribution system was 1.5:1 and almost 1:1 for the surface water system. The measured (regulated) DBPs only accounted for 16 to 33% of the total organic halogen, demonstrating that AOX measurements are essential to provide a full understanding of the formation of halogenated DBPs in drinking waters. In addition, the study demonstrated that a significant proportion (up to 94%) of the bromide in source waters can be converted AOBr. An evaluation of AOBr and AOCl through a second groundwater treatment plant that uses conventional treatment processes for DOC removal produced 70% of AOX as AOBr, with 69% of the initial source water bromide converted to AOBr. Exposure to organobromine compounds is suspected to result in greater adverse health consequences than their chlorinated analogues. Therefore, this study highlights the need for improved methods to selectively reduce the bromide content in source waters. Copyright © 2015 Elsevier B.V. All rights reserved.

REACTIONS OF CHLORINE IN DRINKING WATER, WITH HUMIC ACIDS AND 'IN VIVO'

EPA Science Inventory

The use of chlorine as a drinking water disinfectant is known to produce a variety of chlorinated and oxidized derivatives of organic matter present in the source water. Humic substances, which represent the major fraction of the organic matter in natural waters, have been shown ...

The impact of iodinated X-ray contrast agents on formation and toxicity of disinfection by-products in drinking water.

PubMed

Jeong, Clara H; Machek, Edward J; Shakeri, Morteza; Duirk, Stephen E; Ternes, Thomas A; Richardson, Susan D; Wagner, Elizabeth D; Plewa, Michael J

2017-08-01

The presence of iodinated X-ray contrast media (ICM) in source waters is of high concern to public health because of their potential to generate highly toxic disinfection by-products (DBPs). The objective of this study was to determine the impact of ICM in source waters and the type of disinfectant on the overall toxicity of DBP mixtures and to determine which ICM and reaction conditions give rise to toxic by-products. Source waters collected from Akron, OH were treated with five different ICMs, including iopamidol, iopromide, iohexol, diatrizoate and iomeprol, with or without chlorine or chloramine disinfection. The reaction product mixtures were concentrated with XAD resins and the mammalian cell cytotoxicity and genotoxicity of the reaction mixture concentrates was measured. Water containing iopamidol generated an enhanced level of mammalian cell cytotoxicity and genotoxicity after disinfection. While chlorine disinfection with iopamidol resulted in the highest cytotoxicity overall, the relative iopamidol-mediated increase in toxicity was greater when chloramine was used as the disinfectant compared with chlorine. Four other ICMs (iopromide, iohexol, diatrizoate, and iomeprol) expressed some cytotoxicity over the control without any disinfection, and induced higher cytotoxicity when chlorinated. Only iohexol enhanced genotoxicity compared to the chlorinated source water. Copyright © 2017. Published by Elsevier B.V.

Two-chamber configuration of Bio-Nano electron cyclotron resonance ion source for fullerene modification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uchida, T., E-mail: uchida-t@toyo.jp; Graduate School of Interdisciplinary New Science, Toyo University, Kawagoe 350-8585; Rácz, R.

2016-02-15

We report on the modification of fullerenes with iron and chlorine using two individually controllable plasmas in the Bio-Nano electron cyclotron resonance ion source (ECRIS). One of the plasmas is composed of fullerene and the other one is composed of iron and chlorine. The online ion beam analysis allows one to investigate the rate of the vapor-phase collisional modification process in the ECRIS, while the offline analyses (e.g., liquid chromatography-mass spectrometry) of the materials deposited on the plasma chamber can give information on the surface-type process. Both analytical methods show the presence of modified fullerenes such as fullerene-chlorine, fullerene-iron, andmore » fullerene-chlorine-iron.« less

The sorption properties of polymers with molecular imprints of chlorine-containing pesticides

NASA Astrophysics Data System (ADS)

Popov, S. A.; Dmitrienko, S. G.; Chumichkina, Yu. A.; Zolotov, Yu. A.

2009-04-01

Polymers with molecular imprints of 2,4-dichlorophenoxyacetic acid (2,4-D), 3,6-dichloro-2-methoxybenzoic acid (dicamba), and (RS)-1- p-chlorophenyl-4,4-dimethyl-3-(1H-1,2,4-triazol-1-ylmethyl) pentan-3-ol and the corresponding blank polymers were synthesized using acrylamide as a functional monomer. The specific surface area of the resulting materials was estimated and their sorption properties were studied. It was found that the sorption characteristics of the polymers with molecular imprints of chlorine-containing pesticides depended on the nature of template molecules, functional monomer: template ratio in the polymerization mixture, and nature and content of solvents varied at the synthesis stage. According to the sorption isotherms, the difference in the sorption behavior of molecularly imprinted and blank polymers was observed over a wide range of chlorine-containing pesticide concentrations. The selectivity of the adsorbent with 2,4-D imprints was estimated for the example of structurally related compounds.

UV-Vis spectroscopy and solvatochromism of the tyrosine kinase inhibitor AG-1478

NASA Astrophysics Data System (ADS)

Khattab, Muhammad; Wang, Feng; Clayton, Andrew H. A.

2016-07-01

The effect of twenty-one solvents on the UV-Vis spectrum of the tyrosine kinase inhibitor AG-1478 was investigated. The absorption spectrum in the range 300-360 nm consisted of two partially overlapping bands at approximately 340 nm and 330 nm. The higher energy absorption band was more sensitive to solvent and exhibited a peak position that varied from 327 nm to 336 nm, while the lower energy absorption band demonstrated a change in peak position from 340 nm to 346 nm in non-chlorinated solvents. The fluorescence spectrum of AG-1478 was particularly sensitive to solvent. The wavelength of peak intensity varied from 409 nm to 495 nm with the corresponding Stokes shift in the range of 64 nm to 155 nm (4536 cm- 1 to 9210 cm- 1). We used a number of methods to assess the relationship between spectroscopic properties and solvent properties. The detailed analysis revealed that for aprotic solvents, the peak position of the emission spectrum in wavenumber scale correlated with the polarity (dielectric constant or ET(30)) of the solvent. In protic solvents, a better correlation was observed between the hydrogen bonding power of the solvent and the position of the emission spectrum. Moreover, the fluorescence quantum yields were larger in aprotic solvents as compared to protic solvents. This analysis underscores the importance of polarity and hydrogen-bonding environment on the spectroscopic properties of AG-1478. These studies will assume relevance in understanding the interaction of AG-1478 in vitro and in vivo.

In situ remediation of DNAPL compounds in low permeability media fate/transport, in situ control technologies, and risk reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-08-01

In this project, in situ remediation technologies are being tested and evaluated for both source control and mass removal of dense, non-aqueous phase liquid (DNAPL) compounds in low permeability media (LPM). This effort is focused on chlorinated solvents (e.g., trichloroethylene and perchloroethylene) in the vadose and saturated zones of low permeability, massive deposits, and stratified deposits with inter-bedded clay lenses. The project includes technology evaluation and screening analyses and field-scale testing at both clean and contaminated sites in the US and Canada. Throughout this project, activities have been directed at understanding the processes that influence DNPAL compound migration and treatmentmore » in LPM and to assessing the operation and performance of the remediation technologies developed and tested. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.« less

Compound-specific isotope analysis: Questioning the origins of a trichloroethene plume

USGS Publications Warehouse

Eberts, S.M.; Braun, C.; Jones, S.

2008-01-01

Stable carbon isotope ratios of trichloroethene (TCE), cis-1,2- dichloroethene, and trans-1,2-dichloroethene were determined by use of gas chromatography-combustion-isotope ratio mass spectroscopy to determine whether compound-specific stable carbon isotopes could be used to help understand the origin and history of a TCE groundwater plume in Fort Worth, TX. Calculated ??13C values for total chlorinated ethenes in groundwater samples, which can approximate the ??13C of a spilled solvent if all degradation products are accounted for, were useful for determining whether separate lobes of the plume resulted from different sources. Most notably, values for one lobe, where tetrachloroethene (PCE) has been detected periodically, were outside the range for manufactured TCE but within the range for manufactured PCE, whereas values for a separate lobe, which is downgradient of reported TCE spills, were within the range for manufactured TCE. Copyright ?? Taylor & Francis Group, LLC.

Non-aqueous cleaning solvent substitution

NASA Technical Reports Server (NTRS)

Meier, Gerald J.

1994-01-01

A variety of environmental, safety, and health concerns exist over use of chlorinated and fluorinated cleaning solvents. Sandia National Laboratories, Lawrence Livermore National Laboratories, and the Kansas City Division of AlliedSignal have combined efforts to focus on finding alternative cleaning solvents and processes which are effective, environmentally safe, and compliant with local, state, and federal regulations. An alternative solvent has been identified, qualified, and implemented into production of complex electronic assemblies, where aqueous and semi-aqueous cleaning processes are not allowed. Extensive compatibility studies were performed with components, piece-parts, and materials. Electrical testing and accelerated aging were used to screen for detrimental, long-term effects. A terpene, d-limonene, was selected as the solvent of choice, and it was found to be compatible with the components and materials tested. A brief history of the overall project will be presented, along with representative cleaning efficiency results, compatibility results, and residual solvent data. The electronics industry is constantly searching for proven methods and environmentally-safe materials to use in manufacturing processes. The information in this presentation will provide another option to consider on future projects for applications requiring high levels of quality, reliability, and cleanliness from non-aqueous cleaning processes.

A Guide for Selecting Remedies for Subsurface Releases of Chlorinated Solvents

DTIC Science & Technology

2011-03-01

exception of secondary permeability features (e.g., fractures , root holes, animal burrows), high displacement pressures typically preclude DNAPL from...1 to 40 percent. Fractured media with high matrix porosity are commonly encountered in sedimentary rock (e.g., limestone, dolomite , shale, and...Low Permeability .......... 21 Type III – Granular Media with Moderate to High Heterogeneity ........................ 21 Type IV - Fractured Media

DEVELOPMENT OF A SYSTEMATIC APPROACH TO ACCURATELY MEASURE TRACE LEVELS OF VOLATILE ORGANIC COMPOUNDS (VOCS) IN SOIL AND SEDIMENT CONTAINING HIGH MOISTURE TO MEET THE EPA'S RISK ASSESSMENT NEEDS

EPA Science Inventory

A majority of the contaminated sites within the United States contain volatile organic compounds (VOCs), either as industrial chlorinated solvents or petroleum products commonly referred to as BTEX (benzene, toluene, ethyl benzene, and xylene). The present EPA methods for low le...

Application of Nucleic Acid-Based Tools for Monitoring Monitored Natural Attenuation (MNA), Biostimulation and Bioaugmentation at Chlorinated Solvent Sites

DTIC Science & Technology

2010-12-01

K. M. Ritalahti, and J. M. Tiedje. 2003. Diversity of Dechlorinating Bacteria, p. 53-87. In M. M. Häggblom and I. D. Bossert (eds.), Dehalogenation ...Anaerobic Microbial Dehalogenation . Annu. Rev. Microbiol. 58:43-73. Smits, T. H.M., C. Devenoges, K. Szynalski, J. Maillard, and C. Holliger. 2004

Principles and Practices of Enhanced Anaerobic Bioremediation of Chlorinated Solvents

DTIC Science & Technology

2004-08-01

high - fructose corn syrup - xi - 022/738863/28.doc...systems Dissolved in water Continuous to monthly Molasses, High Fructose Corn Syrup Injection wells Dissolved in water Continuous to monthly Viscous...7 to 90 days Suthersan et al., 2002; Appendices E.2 and E.11 High Fructose Corn Syrup Diluted to 1 to 10 percent by weight. 50 to 500 mg/L

MNA for Chlorinated Solvents and Fuel Oxygenates: Why It Occurs, How It Evolved, and Using Stable Carbon Isotopes to Predict Plume Behavior

EPA Science Inventory

The organisms that degrade MtBE under anaerobic conditions are evolved to acquire energy for growth by using molecular hydrogen and carbonate ion to cleave methyl ether bonds. Methyl ether bonds are common in nature and the bond also occurs in MTBE. MTBE in contaminated ground...

Foam Delivery of Hydrogen for Enhanced Aquifer Contacting and Anaerobic Bioremediation of Chlorinated Solvents

DTIC Science & Technology

2005-11-01

101 Task 6 - Incorporation of the heterogeneity enhanced mechanisms in the UTCHEM numerical simulator...hydrogen sparging in a bench scale three-dimensional sand pack model. (6) Incorporation of the heterogeneity enhanced mechanisms in the UTCHEM ...Incorporation of the heterogeneity enhanced mechanisms in the UTCHEM numerical simulator. Simulation model for foam in porous media and

Sustainable in-well vapor stripping: A design, analytical model, and pilot study for groundwater remediation

NASA Astrophysics Data System (ADS)

Sutton, Patrick T.; Ginn, Timothy R.

2014-12-01

A sustainable in-well vapor stripping system is designed as a cost-effective alternative for remediation of shallow chlorinated solvent groundwater plumes. A solar-powered air compressor is used to inject air bubbles into a monitoring well to strip volatile organic compounds from a liquid to vapor phase while simultaneously inducing groundwater circulation around the well screen. An analytical model of the remediation process is developed to estimate contaminant mass flow and removal rates. The model was calibrated based on a one-day pilot study conducted in an existing monitoring well at a former dry cleaning site. According to the model, induced groundwater circulation at the study site increased the contaminant mass flow rate into the well by approximately two orders of magnitude relative to ambient conditions. Modeled estimates for 5 h of pulsed air injection per day at the pilot study site indicated that the average effluent concentrations of dissolved tetrachloroethylene and trichloroethylene can be reduced by over 90% relative to the ambient concentrations. The results indicate that the system could be used cost-effectively as either a single- or multi-well point technology to substantially reduce the mass of dissolved chlorinated solvents in groundwater.

Phytoremediation of Trichloroethylene and Perchloroethylene at the Savannah River Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brigmon, R.L.

Bioremediation of chlorinated solvents, both natural and accelerated, is exemplified by phytoremediation and biodegradation by rhizosphere microorganisms. Phytoremediation is the use of vegetation for the treatment of contaminated soils, sediments, and water. The potential for phytoremediation of chlorinated solvents has been demonstrated at the Savannah River Site (SRS) Miscellaneous Chemical Basin, Southern Sector of A/M Area and TNX/D-Area. Recent characterization work at the SRS has delineated widespread plumes (1-2 miles) of low concentration (40 ppb -10-ppm range) trichloroethylene (TCE) and perchloroethylene (PCE) contaminated groundwater. Phytoremediation deployments are underway for TCE and PCE phytoremediation in select SRS areas. Phytoremediation appears tomore » be an excellent technology to intercept and control plume migration. The ongoing Southern Sector treatability study is part of a multi-year field study of SRS seepline-soil systems maintained under saturated conditions. The primary focus is on determining how trees, seepline groundcover, soil microbial communities, and geochemical and surface-volatilization processes affect TCE and PCE in contaminated groundwater that flows through surface seepline areas. Therefore, FY00 represented an initial acclimation phase for soil and plant systems and will facilitate examination of seepline phyto- and bioactivity in subsequent growth season in FY01.« less

Disinfection byproduct formation in reverse-osmosis concentrated and lyophilized natural organic matter from a drinking water source.

PubMed

Pressman, Jonathan G; McCurry, Daniel L; Parvez, Shahid; Rice, Glenn E; Teuschler, Linda K; Miltner, Richard J; Speth, Thomas F

2012-10-15

Drinking water treatment and disinfection byproduct (DBP) research can be complicated by natural organic matter (NOM) temporal variability. NOM preservation by lyophilization (freeze-drying) has been long practiced to address this issue; however, its applicability for drinking water research has been limited because the selected NOM sources are atypical of most drinking water sources. The purpose of this research was to demonstrate that reconstituted NOM from a lyophilized reverse-osmosis (RO) concentrate of a typical drinking water source closely represents DBP formation in the original NOM. A preliminary experiment assessed DBP formation kinetics and yields in concentrated NOM, which demonstrated that chlorine decays faster in concentrate, in some cases leading to altered DBP speciation. Potential changes in NOM reactivity caused by lyophilization were evaluated by chlorination of lyophilized and reconstituted NOM, its parent RO concentrate, and the source water. Bromide lost during RO concentration was replaced by adding potassium bromide prior to chlorination. Although total measured DBP formation tended to decrease slightly and unidentified halogenated organic formation tended to increase slightly as a result of RO concentration, the changes associated with lyophilization were minor. In lyophilized NOM reconstituted back to source water TOC levels and then chlorinated, the concentrations of 19 of 21 measured DBPs, constituting 96% of the total identified DBP mass, were statistically indistinguishable from those in the chlorinated source water. Furthermore, the concentrations of 16 of 21 DBPs in lyophilized NOM reconstituted back to the RO concentrate TOC levels, constituting 86% DBP mass, were statistically indistinguishable from those in the RO concentrate. This study suggests that lyophilization can be used to preserve concentrated NOM without substantially altering the precursors to DBP formation. Published by Elsevier Ltd.

Life Cycle Environmental Impacts of Disinfection Technologies Used in Small Drinking Water Systems.

PubMed

Jones, Christopher H; Shilling, Elizabeth G; Linden, Karl G; Cook, Sherri M

2018-03-06

Small drinking water systems serve a fifth of the U.S. population and rely heavily on disinfection. While chlorine disinfection is common, there is interest in minimizing chemical addition, especially due to carcinogenic disinfection byproducts and chlorine-resistant pathogens, by using ultraviolet technologies; however, the relative, broader environmental impacts of these technologies are not well established, especially in the context of small (<10 000 people) water systems. The objective of this study was to identify environmental trade-offs between chlorine and ultraviolet disinfection via comparative life cycle assessment. The functional unit was the production of 1 m 3 of drinking water to U.S. Treatment included cartridge filtration followed by either chlorine disinfection or ultraviolet disinfection with chlorine residual addition. Environmental performance was evaluated for various chlorine contact zone materials (plastic, concrete, steel), ultraviolet validation factors (1.2 to 4.4), and electricity sources (renewable; U.S. average, high, and low impact grids). Performance was also evaluated when filtration and chlorine residual were not required. From a life cycle assessment perspective, replacing chlorine with UV was preferred only in a limited number of cases (i.e., high pumping pressure but filtration is not required). In all others, chlorine was environmentally preferred, although some contact zone materials and energy sources had an impact on the comparison. Utilities can use these data to inform their disinfection technology selection and operation to minimize environmental and human health impacts.

Solid-phase microextraction of organophosphate pesticides in source waters for drinking water treatment facilities.

PubMed

Flynt, Elizabeth; Dupuy, Aubry; Kennedy, Charles; Bennett, Shanda

2006-09-01

The rapid detection of contaminants in our nation's drinking water has become a top homeland security priority in this time of increased national vigilance. Real-time monitoring of drinking water for deliberate or accidental contamination is key to national security. One method that can be employed for the rapid screening of pollutants in water is solid-phase microextraction (SPME). SPME is a rapid, sensitive, solvent-free system that can be used to screen for contaminants that have been accidentally or intentionally introduced into a water system. A method using SPME has been developed and optimized for the detection of seven organophosphate pesticides in drinking water treatment facility source waters. The method is tested in source waters for drinking water treatment facilities in Mississippi and Alabama. Water is collected from a deepwater well at Stennis Space Center (SSC), MS, the drinking water source for SSC, and from the Converse Reservoir, the main drinking water supply for Mobile, AL. Also tested are samples of water collected from the Mobile Alabama Water and Sewer System drinking water treatment plant prior to chlorination. The method limits of detection for the seven organophosphates were comparable to those described in several Environmental Protection Agency standard methods. They range from 0.25 to 0.94 microg/L.

Redox conditions and the efficiency of chlorinated ethene biodegradation: Field studies

USGS Publications Warehouse

Chapelle, F.H.; Bradley, P.M.

2000-01-01

The effect of redox conditions on the efficiency of chlorinated ethene biodegradation was investigated at two field sites. One site (NAS Cecil Field, FL) is characterized by predominantly Fe(III)-reducing conditions in the contaminant source area, grading to predominantly sulfate- reducing conditions downgradient. This sequence of redox conditions led to relatively inefficient biodegradation of chlorinated ethenes, with high concentrations of trichloroethene extending more than 400 meters downgradient of the source area. In contrast, a second site (NBS Kings Bay, GA) characterized by predominantly sulfate-reducing conditions in the source area followed by Fe(III)-reducing conditions downgradient. In this system perchloroethene (PCE) and TCE were rapidly biodegraded and extended less than 100 meters downgradient. Rates of ground- water transport are similar at the two sites (???0.2 m/d) indicating that the succession of redox processes, rather than other hydrologic factors, is the principal control on biodegradation. In particular, redox conditions that favor the initial reduction of highly chlorinated ethenes (methanogenic or sulfate-reducing conditions) followed by more oxidizing conditions (Fe(III)- reducing or oxic conditions) favors efficient biodegradation. Thus, documenting the succession of redox processes is an important step in understanding the efficiency of chlorinated ethene biodegradation in ground-water systems.

Atmospheric reactivity of alcohols, thiols and fluoroalcohols with chlorine atoms

NASA Astrophysics Data System (ADS)

Garzon Ruiz, Andres

Alcohols, thiols and fluoroalcohols are volatile organic compounds (VOCs) which are emitted to the atmosphere from both natural (vegetation, oceans, volcanoes, etc.) and anthropogenic sources (fuels, solvents, wastewater, incinerators, refrigerants, etc.). These pollutants can be eliminated from the troposphere by deposition on the terrestrial surface, direct photolysis or reaction with different tropospheric oxidants. Reactions of VOCs with tropospheric oxidants are involved in the well-known atmospheric phenomenon of photochemical smog or the production of tropospheric ozone. The oxidation of these VOCs in the troposphere is mainly initiated by reaction with OH radicals during the daytime and with NO radicals at night. However, in recent years, the oxidation by chlorine atoms (Cl) has gained great importance in the study of atmospheric reactions because they may exert some influence in the boundary layer, particularly in marine and coastal environments. In general, Cl atoms are much more reactive species than OH and NO; radicals and therefore low concentrations of Cl may compete with OH and NO3 in hydrocarbon oxidation processes. The main source of tropospheric Cl atoms is believed to be the photolysis of chlorine-containing molecules generated by heterogeneous reactions of sea salt aerosols. It has also been proposed that Cl atoms, produced in the photolysis of Cl2 emitted from industrial processes, may enhance hydrocarbon oxidation rates and ozone production in urban environments. In this work, a kinetic, theoretical and mechanistic study of the reaction of several alcohols, thiols, and fluoroalcohols with Cl atoms has been carried out. Pulsed laser photolysis-fluorescence resonance (PLP-RF) technique was used for the kinetic study as a function of temperature and pressure. An environmental chamber-Fourier transform infrared (FTIR) system was also employed in the kinetic studies. Tropospheric lifetimes of these pollutants were estimated using obtained kinetic data. Products of these reactions were determined by FTIR and derivatization with 2,4-dinitrophenylhydrazine and HPLC analysis. Finally, in order to determine the main reaction pathways a theoretical study at QCISD(T)/6-311G**//MP2(Full)(6-311C** level was performed for each reaction.

Sources and occurrence of chloroform and other trihalomethanes in drinking-water supply wells in the United States, 1986-2001

USGS Publications Warehouse

Ivahnenko, Tamara; Zogorski, J.S.

2006-01-01

Chloroform and three other trihalomethanes (THMs)--bromodichloromethane, dibromochloromethane, and bromoform--are disinfection by-products commonly produced during the chlorination of water and wastewater. Samples of untreated ground water from drinking-water supply wells (1,096 public and 2,400 domestic wells) were analyzed for THMs and other volatile organic compounds (VOCs) during 1986-2001, or compiled, as part of the U.S. Geological Survey's National Water-Quality Assessment Program. This report provides a summary of potential sources of THMs and of the occurrence and geographical distribution of THMs in samples from public and domestic wells. Evidence for an anthropogenic source of THMs and implications for future research also are presented. Potential sources of THMs to both public and domestic wells include the discharge of chlorinated drinking water and wastewater that may be intentional or inadvertent. Intentional discharge includes the use of municipally supplied chlorinated water to irrigate lawns, golf courses, parks, gardens, and other areas; the use of septic systems; or the regulated discharge of chlorinated wastewater to surface waters or ground-water recharge facilities. Inadvertent discharge includes leakage of chlorinated water from swimming pools, spas, or distribution systems for drinking water or wastewater sewers. Statistical analyses indicate that population density, the percentage of urban land, and the number of Resource Conservation and Recovery Act hazardous-waste facilities near sampled wells are significantly associated with the probability of detection of chloroform, especially for public wells. Domestic wells may have several other sources of THMs, including the practice of well disinfection through shock chlorination, laundry wastewater containing bleach, and septic system effluent. Chloroform was the most frequently detected VOC in samples from drinking-water supply wells (public and domestic wells) in the United States. Although chloroform was detected frequently in samples from public and domestic wells and the other THMs were detected in some samples, no concentrations in samples from either well type exceeded the U.S. Environmental Protection Agency's Maximum Contaminant Level of 80 micrograms per liter for total THMs. Chloroform was detected in public well samples almost twice as frequently (11 percent) as in domestic well samples (5 percent). The other three THMs also were detected more frequently in public well samples than in domestic well samples. This detection pattern may be attributed to public wells having a higher pumping capacity than domestic wells. The higher capacity wells create a larger capture zone that potentially intercepts more urban and other land uses and associated point and nonpoint sources of contamination than the smaller capacity domestic wells. THM detection frequencies in domestic well samples show a pattern of decreasing frequency with increasing bromide content, that is in the order: chloroform > bromodichloromethane >= dibromochloromethane >= bromoform. This same pattern has been documented in studies of water chlorination, indicating that an important source of chloroform and other THMs in drinking-water supply wells may be the recycling of chlorinated water and wastewater. Mixtures of THMs commonly occur in public well samples, and the most frequently occurring are combinations of the brominated THMs. These THMs have limited industrial production, few natural sources, and small or no reported direct releases to the environment. Therefore, industrial, commercial, or natural sources are not likely sources of the brominated THMs in public and domestic well samples. The THM detection frequency pattern, the co-occurrence of brominated THMs, and other lines of evidence indicate that the recycling of water with a history of chlorination is an important source of these compounds in samples from drinking-water supply wells.

Occupational solvent exposure and cognition

PubMed Central

Sabbath, E.L.; Glymour, M.M.; Berr, C.; Singh-Manoux, A.; Zins, M.; Goldberg, M.

2012-01-01

Objective: Chronic occupational solvent exposure is associated with long-term cognitive deficits. Cognitive reserve may protect solvent-exposed workers from cognitive impairment. We tested whether the association between chronic solvent exposure and cognition varied by educational attainment, a proxy for cognitive reserve. Methods: Data were drawn from a prospective cohort of French national gas and electricity (GAZEL) employees (n = 4,134). Lifetime exposure to 4 solvent types (chlorinated solvents, petroleum solvents, benzene, and nonbenzene aromatic solvents) was assessed using a validated job-exposure matrix. Education was dichotomized at less than secondary school or below. Cognitive impairment was defined as scoring below the 25th percentile on the Digit Symbol Substitution Test at mean age 59 (SD 2.8; 88% of participants were retired at testing). Log-binomial regression was used to model risk ratios (RRs) for poor cognition as predicted by solvent exposure, stratified by education and adjusted for sociodemographic and behavioral factors. Results: Solvent exposure rates were higher among less-educated patients. Within this group, there was a dose-response relationship between lifetime exposure to each solvent type and RR for poor cognition (e.g., for high exposure to benzene, RR = 1.24, 95% confidence interval 1.09–1.41), with significant linear trends (p < 0.05) in 3 out of 4 solvent types. Recency of solvent exposure also predicted worse cognition among less-educated patients. Among those with secondary education or higher, there was no significant or near-significant relationship between any quantification of solvent exposure and cognition. Conclusions: Solvent exposure is associated with poor cognition only among less-educated individuals. Higher cognitive reserve in the more-educated group may explain this finding. PMID:22641403

Chlorine poisoning

MedlinePlus

... the body to form hydrochloric acid and hypochlorous acid. Both are extremely poisonous. ... has been closed all winter) Mild cleaners Some bleach products ... This list may not include all uses and sources of chlorine.

LLNL Experimental Test Site (Site 300) Potable Water System Operations Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ocampo, R. P.; Bellah, W.

The existing Lawrence Livermore National Laboratory (LLNL) Site 300 drinking water system operation schematic is shown in Figures 1 and 2 below. The sources of water are from two Site 300 wells (Well #18 and Well #20) and San Francisco Public Utilities Commission (SFPUC) Hetch-Hetchy water through the Thomas shaft pumping station. Currently, Well #20 with 300 gallons per minute (gpm) pump capacity is the primary source of well water used during the months of September through July, while Well #18 with 225 gpm pump capacity is the source of well water for the month of August. The well watermore » is chlorinated using sodium hypochlorite to provide required residual chlorine throughout Site 300. Well water chlorination is covered in the Lawrence Livermore National Laboratory Experimental Test Site (Site 300) Chlorination Plan (“the Chlorination Plan”; LLNL-TR-642903; current version dated August 2013). The third source of water is the SFPUC Hetch-Hetchy Water System through the Thomas shaft facility with a 150 gpm pump capacity. At the Thomas shaft station the pumped water is treated through SFPUC-owned and operated ultraviolet (UV) reactor disinfection units on its way to Site 300. The Thomas Shaft Hetch- Hetchy water line is connected to the Site 300 water system through the line common to Well pumps #18 and #20 at valve box #1.« less

Lawrence Livermore National Laboratory Experimental Test Site (Site 300) Potable Water System Operations Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ocampo, Ruben P.; Bellah, Wendy

The existing Lawrence Livermore National Laboratory (LLNL) Site 300 drinking water system operation schematic is shown in Figures 1 and 2 below. The sources of water are from two Site 300 wells (Well #18 and Well #20) and San Francisco Public Utilities Commission (SFPUC) Hetch-Hetchy water through the Thomas shaft pumping station. Currently, Well #20 with 300 gallons per minute (gpm) pump capacity is the primary source of well water used during the months of September through July, while Well #18 with 225 gpm pump capacity is the source of well water for the month of August. The well watermore » is chlorinated using sodium hypochlorite to provide required residual chlorine throughout Site 300. Well water chlorination is covered in the Lawrence Livermore National Laboratory Experimental Test Site (Site 300) Chlorination Plan (“the Chlorination Plan”; LLNL-TR-642903; current version dated August 2013). The third source of water is the SFPUC Hetch-Hetchy Water System through the Thomas shaft facility with a 150 gpm pump capacity. At the Thomas shaft station the pumped water is treated through SFPUC-owned and operated ultraviolet (UV) reactor disinfection units on its way to Site 300. The Thomas Shaft Hetch- Hetchy water line is connected to the Site 300 water system through the line common to Well pumps #18 and #20 at valve box #1.« less

INTERACTION OF AQUEOUS SOLUTIONS OF CHLORINE WITH MALIC ACID, TARTARIC ACID, AND VARIOUS FRUIT JUICES, A SOURCE OF MUTAGENS

EPA Science Inventory

The interactions of aqueous solutions of chlorine with some fruit acids (citric acid, DL-malic acid, and L-tartaric acid) at different pH values were studied. iethyl ether extraction followed by GC/MS analysis indicated that a number of mutagens (certain chlorinated propanones an...

Response surface model for the reduction of Salmonella biofilm on stainless steel with lactic acid, ethanol and chlorine as controlling factors

USDA-ARS?s Scientific Manuscript database

Bacterial colonization and biofilm formation on food contact surfaces can be sources of contamination of processed foods and poses a serious threat to health. Since chlorine- or ethanol-based disinfection is commonly used in the food industry and kitchens, a disinfectant containing chlorine (Cl), et...

SPINE: SParse eIgengene NEtwork linking gene expression clusters in Dehalococcoides mccartyi to perturbations in experimental conditions

DOE PAGES

Mansfeldt, Cresten B.; Logsdon, Benjamin A.; Debs, Garrett E.; ...

2015-02-25

We present a statistical model designed to identify the effect of experimental perturbations on the aggregate behavior of the transcriptome expressed by the bacterium Dehalococcoides mccartyi strain 195. Strains of Dehalococcoides are used in sub-surface bioremediation applications because they organohalorespire tetrachloroethene and trichloroethene (common chlorinated solvents that contaminate the environment) to non-toxic ethene. However, the biochemical mechanism of this process remains incompletely described. Additionally, the response of Dehalococcoides to stress-inducing conditions that may be encountered at field-sites is not well understood. The constructed statistical model captured the aggregate behavior of gene expression phenotypes by modeling the distinct eigengenes of 100more » transcript clusters, determining stable relationships among these clusters of gene transcripts with a sparse network-inference algorithm, and directly modeling the effect of changes in experimental conditions by constructing networks conditioned on the experimental state. Based on the model predictions, we discovered new response mechanisms for DMC, notably when the bacterium is exposed to solvent toxicity. The network identified a cluster containing thirteen gene transcripts directly connected to the solvent toxicity condition. Transcripts in this cluster include an iron-dependent regulator (DET0096-97) and a methylglyoxal synthase (DET0137). To validate these predictions, additional experiments were performed. Continuously fed cultures were exposed to saturating levels of tetrachloethene, thereby causing solvent toxicity, and transcripts that were predicted to be linked to solvent toxicity were monitored by quantitative reverse-transcription polymerase chain reaction. Twelve hours after being shocked with saturating levels of tetrachloroethene, the control transcripts (encoding for a key hydrogenase and the 16S rRNA) did not significantly change. By contrast, transcripts for DET0137 and DET0097 displayed a 46.8±11.5 and 14.6±9.3 fold up-regulation, respectively, supporting the model. This is the first study to identify transcripts in Dehalococcoides that potentially respond to tetrachloroethene solvent-toxicity conditions that may be encountered near contamination source zones in sub-surface environments.« less

Persistence of two Trichomonas gallinae isolates in chlorinated and distilled water with or without organic material.

PubMed

Gerhold, Richard W; Maestas, Lauren P; Harnage, Philip M

2013-09-01

Trichomonas gallinae is a protozoan parasite commonly found in columbids, passerines, and raptors. In passerines and columbids, trichomonosis causes significant morbidity and mortality associated with contaminated bird feeders and waters. However, there has been little work on the persistence of T. gallinae in water to determine if artificial waters are a likely source of infection for naive birds. To examine drinking water as a source of T. gallinae transmission, we inoculated 1 x 10(6) trichomonads into containers with 500 ml of either distilled or chlorinated water. In addition, we inoculated the same number of trichomonads in distilled or chlorinated water contaminated with 15 g organic matter. Aliquots of 0.5 ml were collected from each container at 0, 0.5, 1, 5, 10, or 20 min; inoculated into a Trichomonas culture packet; and incubated at 37 C for 6 days. Survival was best in the presence of organic matter, with either distilled or chlorinated water. Uncontaminated chlorinated water did not allow survival at any sampling period.

Evaluation of Innovative Volatile Organic Compound and Hazardous Air Pollutant Control Technologies for U.S. Air Force Paint Spray Booths

DTIC Science & Technology

1990-10-01

adsorption/incineration * Membrane vapor separation/condensation * Supercritical fluid oxidation • UV/ozone destruction * Molten salt combustion process...separation/ separate air stream contaminants 9 Oxygenated solvents condensation * Chlorinated hydrocarbons Supercritical fluid * Technology utilizing high...testing or full-scale unit capacity; they are: * Supercritical fluid oxidation • UV/ozone destruction * Molten salt incineration * Infrared incineration

DISCUSSION ON "ELECTROCHEMICAL AND RAMAN SPECTROSCOPIC STUDIES OF THE INFLUENCE OF CHLORINATED SOLVENTS ON THE CORROSION BEHAVIOUR OF IRON IN BORATE BUFFER AND IN SIMULATED GROUNDWATER (CORROSION SCIENCE 2000;42:1921-1939)." (R827117)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Application of Nucleic Acid-Based Tools for Monitoring Monitored Natural Attenuation (MNA), Biostimulation and Bioaugmentation at Chlorinated Solvent Sites

DTIC Science & Technology

2011-02-01

TABLE OF CONTENTS TABLE OF CONTENTS ............................................................................................................... ii...gallons. In 1978, the lagoons were emptied by pumping the contents into the A-Block Lagoon (SWMU 22), a ESTCP ER-0518 Final Report 25...feet bgs, but deeper at some locations, the clay content increased significantly. In approximately 20 to 30 feet above bedrock, sandy clay and clayey

A Case Study of Using Zero-Valent Iron Nanoparticles for Groundwater Remediation

NASA Astrophysics Data System (ADS)

Xiong, Z.; Kaback, D.; Bennett, P. J.

2011-12-01

Zero-valent iron nanoparticle (nZVI) is a promising technology for rapid in situ remediation of numerous contaminants, including chlorinated solvents, in groundwater and soil. Because of the high specific surface area of nZVI particles, this technology achieves treatment rates that are significantly faster than micron-scale and granular ZVI. However, a key technical challenge facing this technology involves agglomeration of nZVI particles. To improve nZVI mobility/deliverability and reactivity, an innovative method was recently developed using a low-cost and bio-degradable organic polymer as a stabilizer. This nZVI stabilization strategy offers unique advantages including: (1) the organic polymer is cost-effective and "green" (completely bio-compatible), (2) the organic polymer is highly effective in stabilizing nZVI particles; and (3) the stabilizer is applied during particle preparation, making nZVI particles more stable. Through a funding from the U.S. Air Force Center for Engineering and the Environment (AFCEE), AMEC performed a field study to test the effectiveness of this innovative technology for degradation of chlorinated solvents in groundwater at a military site. Laboratory treatability tests were conducted using groundwater samples collected from the test site and results indicated that trichloroethene (main groundwater contaminant at the site) was completely degraded within four hours by nZVI particles. In March and May 2011, two rounds of nZVI injection were performed at the test site. Approximately 700 gallons of nZVI suspension with palladium as a catalyst were successfully prepared in the field and injected into the subsurface. Before injection, membrane filters with a pore size of 450 nm were used to check the nZVI particle size and it was observed that >85% of nZVI particles were passed through the filter based on total iron measurement, indicating particle size of <450 nm. During field injections, nZVI particles were observed in a monitoring well located 5 feet downgradient from the injection well. Chlorinated solvent degradation products, e.g. ethane and ethene, increased significantly in monitoring wells following nZVI injections. Groundwater monitoring will be continued for approximately eight months following the last sampling event in July 2011 to demonstrate the performance of nZVI particles.

Metagenome phylogenetic profiling of microbial community evolution in a tetrachloroethene-contaminated aquifer responding to enhanced reductive dechlorination protocols.

PubMed

Reiss, Rebecca A; Guerra, Peter; Makhnin, Oleg

2016-01-01

Chlorinated solvent contamination of potable water supplies is a serious problem worldwide. Biostimulation protocols can successfully remediate chlorinated solvent contamination through enhanced reductive dechlorination pathways, however the process is poorly understood and sometimes stalls creating a more serious problem. Whole metagenome techniques have the potential to reveal details of microbial community changes induced by biostimulation. Here we compare the metagenome of a tetrachloroethene contaminated Environmental Protection Agency Superfund Site before and after the application of biostimulation protocols. Environmental DNA was extracted from uncultured microbes that were harvested by on-site filtration of groundwater one month prior to and five months after the injection of emulsified vegetable oil, nutrients, and hydrogen gas bioamendments. Pair-end libraries were prepared for high-throughput DNA sequencing and 90 basepairs from both ends of randomly fragmented 400 basepair DNA fragments were sequenced. Over 31 millions reads were annotated with Metagenome Rapid Annotation using Subsystem Technology representing 32 prokaryotic phyla, 869 genera, and 3,181 species. A 3.6 log 2 fold increase in biomass as measured by DNA yield per mL water was measured, but there was a 9% decrease in the number of genera detected post-remediation. We apply Bayesian statistical methods to assign false discovery rates to fold-change abundance data and use Zipf's power law to filter genera with low read counts. Plotting the log-rank against the log-fold-change facilitates the visualization of the changes in the community in response to the enhanced reductive dechlorination protocol. Members of the Archaea domain increased 4.7 log 2 fold, dominated by methanogens. Prior to remediation, classes Alphaproteobacteria and Betaproteobacteria dominated the community but exhibit significant decreases five months after biostimulation. Geobacter and Sulfurospirillum replace " Sideroxydans " and Burkholderia as the most abundant genera. As a result of biostimulation, Deltaproteobacteria and Epsilonproteobacteria capable of dehalogenation, iron and sulfate reduction, and sulfur oxidation increase. Matches to thermophilic, haloalkane respiring archaea is evidence for additional species involved in biodegradation of chlorinated solvents. Additionally, potentially pathogenic bacteria increase, indicating that there may be unintended consequences of bioremediation.

Multidisciplinary investigation of the fate, transport, and remediation of chlorinated solvents in fractured rocks at the former Naval Air Warfare Center (NAWC): Scientific and management challenges, and strategies for a successful research program

NASA Astrophysics Data System (ADS)

Tiedeman, C. R.; Goode, D. J.; Shapiro, A. M.; Lacombe, P. J.; Chapelle, F. H.; Bradley, P. M.; Imbrigiotta, T. E.; Williams, J. H.; Curtis, G. P.; Hsieh, P. A.

2008-12-01

At the former Naval Air Warfare Center (NAWC) in West Trenton NJ, the U.S. Geological Survey, in cooperation with the U.S. Navy and under support from the Strategic Environmental Research and Development Program (SERDP), is investigating the fate, transport, and remediation of trichloroethylene (TCE) and its daughter products in dipping, fractured mudstones underlying the site. TCE concentrations in ground water are as high as ~100 mg/L. Objectives of multidisciplinary research at the NAWC include (1) understanding the physical, chemical, and microbiological processes and properties affecting the fate, transport, and removal of chlorinated solvents in fractured rocks, (2) assessing the efficiency of different remediation methods (pump and treat, natural and enhanced biodegradation), and (3) transferring the results to help remediate other contaminated fractured rock aquifers. There are numerous scientific and technical challenges to meeting these goals, including the extreme spatial variability of flow and transport properties at the NAWC and the complex distribution of contaminants, geochemical constituents, and microorganisms in fractures and the rock matrix. In addition, there are management challenges that are equally important to address in order to achieve a successful research program. These include balancing the requirements of the many parties involved at the site, including researchers, the site owner, and regulatory agencies; and ensuring that limited research funds are directed towards work that addresses the most important scientific questions as well as stakeholder concerns. Strategies for the scientific challenges at NAWC include developing a carefully planned program to characterize spatial variability in rock properties and groundwater constituents so that the data obtained are applicable to solving research questions focused on remediation. Strategies for the management challenges include fostering open lines of communication among all parties and conferring with the U.S. Environmental Protection Agency to ensure that our research is relevant to remediation at Superfund and other hazardous waste sites with chlorinated solvent contamination of fractured rocks.

UV-Vis spectroscopy and solvatochromism of the tyrosine kinase inhibitor AG-1478.

PubMed

Khattab, Muhammad; Wang, Feng; Clayton, Andrew H A

2016-07-05

The effect of twenty-one solvents on the UV-Vis spectrum of the tyrosine kinase inhibitor AG-1478 was investigated. The absorption spectrum in the range 300-360nm consisted of two partially overlapping bands at approximately 340nm and 330nm. The higher energy absorption band was more sensitive to solvent and exhibited a peak position that varied from 327nm to 336nm, while the lower energy absorption band demonstrated a change in peak position from 340nm to 346nm in non-chlorinated solvents. The fluorescence spectrum of AG-1478 was particularly sensitive to solvent. The wavelength of peak intensity varied from 409nm to 495nm with the corresponding Stokes shift in the range of 64nm to 155nm (4536cm(-1) to 9210cm(-1)). We used a number of methods to assess the relationship between spectroscopic properties and solvent properties. The detailed analysis revealed that for aprotic solvents, the peak position of the emission spectrum in wavenumber scale correlated with the polarity (dielectric constant or ET(30)) of the solvent. In protic solvents, a better correlation was observed between the hydrogen bonding power of the solvent and the position of the emission spectrum. Moreover, the fluorescence quantum yields were larger in aprotic solvents as compared to protic solvents. This analysis underscores the importance of polarity and hydrogen-bonding environment on the spectroscopic properties of AG-1478. These studies will assume relevance in understanding the interaction of AG-1478 in vitro and in vivo. Copyright © 2016 Elsevier B.V. All rights reserved.

Factors Influencing TCE Anaerobic Dechlorination Investigated via Simulations of Microcosm Experiments

NASA Astrophysics Data System (ADS)

Mao, X.; Harkness, M.; Lee, M. D.; Mack, E. E.; Dworatzek, S.; Acheson, C.; McCarty, P.; Barry, D. A.; Gerhard, J. I.

2006-12-01

SABRE (Source Area BioREmediation) is a public-private consortium whose charter is to determine if enhanced anaerobic bioremediation can result in effective and quantifiable treatment of chlorinated solvent DNAPL source areas. The focus of this 4-year, $5.7 million research project is a field site in the United Kingdom containing a TCE DNAPL source area. In preparation, a microcosm study was performed to determine the optimal combination of factors to support reductive dechlorination of TCE in site soil and groundwater. The study consisted of 168 bottles distributed between four laboratories (Dupont, GE, SiREM, and Terra Systems) and tested the impact of six carbon substrates (lactate, acetate, methanol, SRS (soybean oil), hexanol, butyl acetate), bioaugmentation with KB-1 bacterial culture, three TCE levels (100 mg/L, 400 mg/L, and 800 mg/L) and two sulphate levels (200 mg/L, >500 mg/L) on TCE dechlorination. This research presents a numerical model designed to simulate the main processes occurring in the microcosms, including substrate fermentation, sequential dechlorination, toxic inhibition, and the influence of sulphate concentration. In calibrating the model to over 60 of the microcosm experiments, lumped parameters were employed to quantify the effect of key factors on the conversion rate of each chlorinated ethene in the TCE degradation sequence. Results quantify the benefit (i.e., increased stepwise dechlorination rate) due to both bioaugmentation and the presence of higher sulphate concentrations. Competitive inhibition is found to increase in significance as TCE concentrations increase; however, inclusion of Haldane inhibition is not supported. Over a wide range of experimental conditions and dechlorination steps, SRS appears to induce relatively little hydrogen limitation, thereby facilitating relatively quick conversion of TCE to ethene. In general, hydrogen limitation is found to increase with increasing TCE concentration and with bioaugmentation, and is most pronounced in the dechlorination of TCE to DCE.

40 CFR 63.1218 - What are the standards for hydrochloric acid production furnaces that burn hazardous waste?

Code of Federal Regulations, 2010 CFR

2010-07-01

...)(5) of this section; (2) For mercury, hydrogen chloride and chlorine gas emissions in excess of the... as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess of the levels... source as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess of the levels...

Free chlorine inactivation of fungi in drinking water sources.

PubMed

Pereira, V J; Marques, R; Marques, M; Benoliel, M J; Barreto Crespo, M T

2013-02-01

The effectiveness of free chlorine for the inactivation of fungi present in settled surface water was tested. In addition, free chlorine inactivation rate constants of Cladosporium tenuissimum, Cladosporium cladosporioides, Phoma glomerata, Aspergillus terreus, Aspergillus fumigatus, Penicillium griseofulvum, and Penicillium citrinum that were found to occur in different source waters were determined in different water matrices (laboratory grade water and settled water). The effect of using different disinfectant concentrations (1 and 3 mg/l), temperatures (21 and 4 °C), and pH levels (6 and 7) was addressed. The sensitivity degree of different fungi isolates to chlorine disinfection varied among different genera with some species showing a higher resistance to disinfection and others expected to be more prone to protection from inactivation by the water matrix components. When the disinfection efficiency measured in terms of the chlorine concentration and contact time (Ct) values needed to achieve 99% inactivation were compared with the Ct values reported as being able to achieve the same degree of inactivation of other microorganisms, fungi were found to be more resistant to chlorine inactivation than bacteria and viruses and less resistant than Cryptosporidium oocysts. Copyright © 2012 Elsevier Ltd. All rights reserved.

Characterization of cobalt(II) chloride-modified condensation polyimide films

NASA Technical Reports Server (NTRS)

Rancourt, J. D.; Taylor, L. T.

1988-01-01

The effect of solvent extraction on the properties of cobalt(II) chloride-modified polyimide films was investigated. Solvent-cast films were prepared from solutions of cobalt chloride in poly(amide acid)/N,N-dimethylacetamide (DMAc) and were subsequently dried and cured in static air, forced air, or inert gas ovens with controlled humidity. The films were extracted by either of the three processes (1) soaking in a tray with distilled water at room temperature, (2) soxhlett extraction with distilled water, or (3) soxhell extraction with DMAc. Extraction with DMAc was found to remove both cobalt and chlorine from the films and to slightly increase bulk thermal stability and both surface resistivity and electrical resistivity.

Fluidized bed desulfurization

NASA Technical Reports Server (NTRS)

Ravindram, M.; Kallvinskas, J. J. (Inventor)

1985-01-01

High sulfur content carbonaceous material, such as coal is desulfurized by continuous fluidized suspension in a reactor with chlorine gas, inert dechlorinating gas and hydrogen gas. A source of chlorine gas, a source of inert gas and a source of hydrogen gas are connected to the bottom inlet through a manifold and a heater. A flow controler operates servos in a manner to continuously and sequentially suspend coal in the three gases. The sulfur content is reduced at least 50% by the treatment.

A Two and Half-Year-Performance Evaluation of a Field Test on Treatment of Source Zone Tetrachloroethene and Its Chlorinated Daughter Products Using Emulsified Zaro Valent Iron Nanoparticles

EPA Science Inventory

A field test of emulsified zero valent iron (EZVI) nanoparticles was conducted at Parris Island, SC, USA and was monitored for two and half years to assess the treatment of subsurface-source zone chlorinated volatile organic compounds (CVOCs) dominated by tetrachloroethene (PCE) ...

Enhanced Attenuation: Chlorinated Organics

DTIC Science & Technology

2008-04-01

attenuation capacity of the aquifer downgradient from the source (e.g., permeable reactive barriers or phytoremediation ) Selection of EA remedies should be...ranging from very aggressive source destruction and removal methods to less energy-intensive methods, such as phytoremediation . In many cases, it...plumes that include chlorinated organics. The flux of organic-rich leachate to underlying aquifers can create favorable conditions for the natural

Comparison of gamma-oryzanol contents in crude rice bran oils from different sources by various determination methods.

PubMed

Yoshie, Ayano; Kanda, Ayato; Nakamura, Takahiro; Igusa, Hisao; Hara, Setsuko

2009-01-01

Although there are various determination methods for gamma -oryzanol contained in rice bran oil by absorptiometry, normal-phase HPLC, and reversed-phase HPLC, their accuracies and the correlations among them have not been revealed yet. Chloroform-containing mixed solvents are widely used as mobile phases in some HPLC methods, but researchers have been apprehensive about its use in terms of safety for the human body and the environment.In the present study, a simple and accurate determination method was developed by improving the reversed-phase HPLC method. This novel HPLC method uses methanol/acetonitrile/acetic acid (52/45/3 v/v/v), a non-chlorinated solvent, as the mobile phase, and shows an excellent linearity (y = 0.9527x + 0.1241, R(2) = 0.9974) with absorptiometry. The mean relative errors among the existing 3 methods and the novel method, determined by adding fixed amounts of gamma-oryzanol into refined rice salad oil, were -4.7% for the absorptiometry, -6.8% for the existing normal-phase HPLC, +4.6% for the existing reversed-phase HPLC, and -1.6% for the novel reversed-phase HPLC method. gamma -Oryzanol content in 12 kinds of crude rice bran oils obtained from different sources were determined by the four methods. The mean content of those oils were 1.75+/-0.18% for the absorptiometry, 1.29+/-0.11% for the existing normal-phase HPLC, 1.51+/-0.10% for the existing reversed-phase HPLC, and 1.54+/-0.19% for the novel reversed-phase HPLC method.

Chlorine hazard evaluation for the zinc-chlorine electric vehicle battery. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zalosh, R.G.; Bajpai, S.N.; Short, T.P.

1980-04-01

An evaluation of the hazards associated with conceivable accidental chlorine releases from zinc-chlorine electric vehicle batteries is presented. Since commercial batteries are not yet available, this hazard assessment is based both on theoretical chlorine dispersion models and small-scale and large-scale spill tests with chlorine hydrate. Six spill tests involving chlorine hydrate indicate that the danger zone in which chlorine vapor concentrations intermittently exceed 100 ppM extends at least 23 m directly downwind of a spill onto a warm road surface. Chlorine concentration data from the hydrate spill tests compare favorably with calculations based on a quasi-steady area source dispersion modelmore » and empirical estimates of the hydrate decomposition rate. The theoretical dispersion model has been combined with assumed hydrate spill probabilities and current motor vehicle accident statistics in order to project expected chlorine-induced fatality rates. These calculations indicate that expected chlorine fatality rates are several times higher in a city with a warm and calm climate than in a colder and windier city. Calculated chlorine-induced fatality rate projections for various climates are presented as a function of hydrate spill probability in order to illustrate the degree of vehicle/battery crashworthiness required to maintain chlorine-induced fatality rates below current vehicle fatility rates due to fires and asphyxiations.« less

INDEPENDENT TECHNICAL REVIEW OF THE FOCUSED FEASIBILITY STUDY AND PROPOSED PLAN FOR DESIGNATED SOLID WASTE MANAGEMENT UNITS CONTRIBUTING TO THE SOUTHWEST GROUNDWATER PLUME AT THE PADUCAH GASEOUS DIFFUSION PLANT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Looney, B.; Eddy-Dilek, C.; Amidon, M.

2011-05-31

The U. S. Department of Energy (DOE) is currently developing a Proposed Plan (PP) for remediation of designated sources of chlorinated solvents that contribute contamination to the Southwest (SW) Groundwater Plume at the Paducah Gaseous Diffusion Plant (PGDP), in Paducah, KY. The principal contaminants in the SW Plume are trichloroethene (TCE) and other volatile organic compounds (VOCs); these industrial solvents were used and disposed in various facilities and locations at PGDP. In the SW plume area, residual TCE sources are primarily in the fine-grained sediments of the Upper Continental Recharge System (UCRS), a partially saturated zone that delivers contaminants downwardmore » into the coarse-grained Regional Gravel Aquifer (RGA). The RGA serves as the significant lateral groundwater transport pathway for the plume. In the SW Plume area, the four main contributing TCE source units are: (1) Solid Waste Management Unit (SWMU) 1 / Oil Landfarm; (2) C-720 Building TCE Northeast Spill Site (SWMU 211A); (3) C-720 Building TCE Southeast Spill Site (SWMU 211B); and (4) C-747 Contaminated Burial Yard (SWMU 4). The PP presents the Preferred Alternatives for remediation of VOCs in the UCRS at the Oil Landfarm and the C-720 Building spill sites. The basis for the PP is documented in a Focused Feasibility Study (FFS) (DOE, 2011) and a Site Investigation Report (SI) (DOE, 2007). The SW plume is currently within the boundaries of PGDP (i.e., does not extend off-site). Nonetheless, reasonable mitigation of the multiple contaminant sources contributing to the SW plume is one of the necessary components identified in the PGDP End State Vision (DOE, 2005). Because of the importance of the proposed actions DOE assembled an Independent Technical Review (ITR) team to provide input and assistance in finalizing the PP.« less

Photocatalytic destruction of chlorinated solvents in water with solar energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacheco, J.E.; Prairie, M.R.; Yellowhorse, L.

1993-08-01

Sandia National Laboratories and the National Renewable Energy Laboratory are developing a photocatalytic process to destroy organic contaminants in water. Tests with common water pollutants have been conducted at Sandia's Solar Thermal Facility using a near commercial scale, single-axis tracking parabolic trough system with a glass pipe reactor mounted at its focus. Experiments at this scale provide verification of laboratory studies and allow examination of design and operation issues at a real-lifescale. The catalyst, titanium dioxide (TiO[sub 2]), is a harmless material found in paint, cosmetics, and toothpaste. Experiments were conducted to determine the effects of key process parameters onmore » destruction rates of chlorinated organic compounds that are common water pollutants. This paper summarizes the engineering-scale results of these experiments and analyses.« less

Determination of the thermal stability of perfluoropolyalkyl ethers by tensimetry

NASA Technical Reports Server (NTRS)

Helmick, Larry A.; Jones, William R., Jr.

1992-01-01

The thermal decomposition temperatures of several perfluoropolyalkyl ether fluids were determined with a computerized tensimeter. In general, the decomposition temperatures of the commercial fluids were all similar and significantly higher than those for noncommercial fluids. Correlation of the decomposition temperatures with the molecular structures of the primary components of the commercial fluids revealed that the stability of the fluids was not affected by carbon chain length, branching, or adjacent difluoroformal groups. Instead, stability was limited by the presence of small quantities of thermally unstable material and/or chlorine-containing material arising from the use of chlorine containing solvents during synthesis. Finally, correlation of decomposition temperatures with molecular weights for two fluids supports a chain cleavage reaction mechanism for one and an unzipping reaction mechanism for the other.

Ecology and distribution of a new biomarker linked to 1,2-dichloropropane dechlorination in subsurface environments

NASA Astrophysics Data System (ADS)

Padilla-Crespo, E.; Loeffler, F. E.

2011-12-01

Reductive dechlorination plays a major role in the transformation and detoxification of chlorinated solvents, including chlorinated ethenes. Molecular biological tools are being applied at contaminated sites in order to assess the process-specific biomarkers that impact site performance, and to monitor the progress of bioremediation approaches. The few current biomarker genes in use provide an incomplete picture of the reductively dechlorinating bacterial community; this is a limitation for implementing enhanced bioremediation and monitored natural attenuation as cleanup strategies at chlorinated solvent contaminated sites. Reductively dehalogenating organisms, particularly Dehalococcoides (Dhc) strains, possess multiple reductive dehalogenase (RDase) genes, which are promising targets to specifically monitor dehalogenation processes of interest. Dehalococcoides populations in two highly enriched cultures (RC and KS) have been implicated in the reductive dechlorination of dechlorination of 1,2-dichloropropane (1,2-D), a widespread halogenated organic pollutant, to the non-toxic propene. Using a combined approach of transcription, expression and molecular analysis a new biomarker linked to 1,2-dichloropropane has been identified in Dhc strains RC and KS providing for the first time, convincing evidence of a specific RDase implicated in 1,2-D dechlorination to propene. Further analyses imply that new biomarker is in a "mobile DNA segment", a genomic island (GI) of horizontal gene transfer origin. A valid quantitative PCR approach was designed to detect and enumerate this gene in cultures and environmental samples; this will be a useful to bioremediation practitioners to more efficiently implement reductive dechlorination as a remediation tool. The new biomarker has been identified in fresh water sediment samples from different geographical locations in Europe, North and South America. Further research aims to shed light on RDase gene dissemination and the adaptation of dehalospiring populations in subsurface environments.

Preparation, structure and luminescent characterization of a series of metal-organic frameworks based on flexible ligands with nitrogen heterocycles and carboxyl

NASA Astrophysics Data System (ADS)

Dai, Hai-yu; Tang, Yu-yuan; Wang, Cui-juan; Chen, Shuang; Tong, Yan; Zhang, Zhi-Bing

2017-12-01

Seven new compounds, [Zn(pypymba)2]n(1), [Co(pypymba)2]n(2), [Cd(pypymba)2]n(3), [Cd(Hpypymba)Cl2]n(4), {[Cd(pypymba)Cl]·C2H5OH·H2O}n(5), [Cd(pypyaa)Cl]n(6), {[Cd2(pyznpy)2Cl2H2O]·H2O}n(7) [Hpypymba = 4-((3-(pyrazin-2-yl)-1H-pyrazol-1-yl)methyl)benzoic acid, Hpyznpy = 4-((3-(pyridin-2-yl)-1H-pyrazol-1-yl)methyl)benzoic acid, Hpypyaa = 2-(3-pyridin-2-yl)-1H-pyrazol-1-yl)acetic acid], were hydrothermally synthesized by tuning the metal ion's species, counter anions, solvents and pH values and characterized by routine methods: XRD, elemental analysis, fluorescence properties analysis, TGA and crystal structure analysis and single-crystal X-ray crystallography. The main structures of the compounds 1, 2, and 3 are extended to similar 3D structures by C-H…N, C-H…O hydrogen bonds and π…π stacking under the same synthesis method. Each Cd(II) node of compound 4 has four chlorine bridges (two pairs of double chlorine); Each Cd(II) node of compounds 5, 6 has two chlorine bridges (a pair of double chlorine bridges), while their spatial structures are expanded in different ways. Compound 7 also contains chlorine atoms, but does not contain chlorine bridged structures. The luminescent properties of compound 7 and the ones immersed in various kinds of organic compounds and nitrate@EtOH solutions have been investigated. Importantly, 7 shows highly sensitive response to nitrobenzene and Fe3+ through luminescence quenching effects, making it a promising luminescent sensor for nitrobenzene and Fe3+.

Simultaneous determination of polycyclic aromatic hydrocarbons and their chlorination by-products in drinking water and the coatings of water pipes by automated solid-phase microextraction followed by gas chromatography-mass spectrometry.

PubMed

Tillner, Jocelyn; Hollard, Caroline; Bach, Cristina; Rosin, Christophe; Munoz, Jean-François; Dauchy, Xavier

2013-11-08

In this study, an automated method for the simultaneous determination of polycyclic aromatic hydrocarbons (PAHs) and their chlorination by-products in drinking water was developed based on online solid-phase microextraction-gas chromatography-mass spectrometry. The main focus was the optimisation of the solid-phase microextraction step. The influence of the agitation rate, type of fibre, desorption time, extraction time, extraction temperature, desorption temperature, and solvent addition was examined. The method was developed and validated using a mixture of 17 PAHs, 11 potential chlorination by-products (chlorinated and oxidised PAHs) and 6 deuterated standards. The limit of quantification was 10 ng/L for all target compounds. The validated method was used to analyse drinking water samples from three different drinking water distribution networks and the presumably coal tar-based pipe coatings of two pipe sections. A number of PAHs were detected in all three networks although individual compositions varied. Several PAH chlorination by-products (anthraquinone, fluorenone, cyclopenta[d,e,f]phenanthrenone, 3-chlorofluoranthene, and 1-chloropyrene) were also found, their presence correlating closely with that of their respective parent compounds. Their concentrations were always below 100 ng/L. In the coatings, all PAHs targeted were detected although concentrations varied between the two coatings (76-12,635 mg/kg and 12-6295 mg/kg, respectively). A number of chlorination by-products (anthraquinone, fluorenone, cyclopenta[d,e,f]phenanthrenone, 3-chlorofluoranthene, and 1-chloropyrene) were also detected (from 40 to 985 mg/kg), suggesting that the reaction of PAHs with disinfectant agents takes place in the coatings and not in the water phase after migration. Copyright © 2013 Elsevier B.V. All rights reserved.

Cracking of Clay Due to Contact with Waste Chlorinated Solvents

NASA Astrophysics Data System (ADS)

Otero, M.; Ayral, D.; Shipan, J.; Goltz, M. N.; Huang, J.; Demond, A. H.

2012-12-01

Clays are known to crack upon desiccation. Desiccation cracks of up to 3 cm wide have been reported in natural soils. This raises the question if a similar behavior is seen when a dense non-aqueous phase liquids (DNAPL) waste is in contact with clay. The contact with organic liquids causes the clay structure to shrink, leading to the formation of cracks. Moreover, DNAPL waste not only contains the organic liquid solvent but also includes surface-active solutes or surfactants. Such solutes can enhance the interaction of the organic solvents with the clay. This research will assess whether or not contact with chlorinated organic waste causes cracking. In order to evaluate the possibility of cracking in the clay, microcosms have been constructed that mimic aquifer systems, consisting of a saturated layer of sand, a saturated layer of bentonite clay and a 2.5 cm layer of either pure chlorinated solvents or DNAPL waste. The onset of cracking for the microcosm with tetrachloroethylene (PCE) waste as the DNAPL layer occurred after ten days of contact. Similarly, at eight days, cracks were observed in a microcosm containing trichloroethylene (TCE) waste . Forty-four days later, the length and number of cracks have grown considerably; with a total crack length of 50 cm on a surface of 80 cm2 in the microcosm containing PCE waste. On the other hand it took approximately 161 days for the clay layer in the microcosm containing pure PCE to crack. To quantity the degree of cracking, crack maps were developed using the image software, Image J. Characteristics like crack length, crack aperture, and the percentage of total length for a range of apertures were calculated using this software. For example, for the PCE waste microcosm, it was calculated that 3.7% of the crack length had an aperture of 100-300 microns, 15.1% of the crack length had an aperture of 300-500 microns, 29.7% of the crack length had an aperture of 500-700 microns, 40.1% of the crack length had an aperture of 700-900 microns, 6.3% had an aperture of 900-1,100 microns and 5.1% had an aperture of over 1,100 microns. These data suggest that aquitards in the field might crack when in contact with the DNAPL waste. Moreover, it is apparent that the waste contains solutes that accelerate the cracking of the clay layer. Thus, models examining the impact of storage in low permeability layers need to consider the possible impact of cracking.

Modeling and optimization of trihalomethanes formation potential of surface water (a drinking water source) using Box-Behnken design.

PubMed

Singh, Kunwar P; Rai, Premanjali; Pandey, Priyanka; Sinha, Sarita

2012-01-01

The present research aims to investigate the individual and interactive effects of chlorine dose/dissolved organic carbon ratio, pH, temperature, bromide concentration, and reaction time on trihalomethanes (THMs) formation in surface water (a drinking water source) during disinfection by chlorination in a prototype laboratory-scale simulation and to develop a model for the prediction and optimization of THMs levels in chlorinated water for their effective control. A five-factor Box-Behnken experimental design combined with response surface and optimization modeling was used for predicting the THMs levels in chlorinated water. The adequacy of the selected model and statistical significance of the regression coefficients, independent variables, and their interactions were tested by the analysis of variance and t test statistics. The THMs levels predicted by the model were very close to the experimental values (R(2) = 0.95). Optimization modeling predicted maximum (192 μg/l) TMHs formation (highest risk) level in water during chlorination was very close to the experimental value (186.8 ± 1.72 μg/l) determined in laboratory experiments. The pH of water followed by reaction time and temperature were the most significant factors that affect the THMs formation during chlorination. The developed model can be used to determine the optimum characteristics of raw water and chlorination conditions for maintaining the THMs levels within the safe limit.

Enhanced photo-activated luminescence for screening polychlorobiphenyls (PCBs) and other related chlorinated compounds

DOEpatents

Vo-Dinh, Tuan

1994-01-01

The presence of polychlorinated biphenyls and other chlorinated compounds in a sample is determined by treating the sample with a photo-activator and then exposing the treated sample to a UV light source. The UV light produces a photo-product complex, which is subsequently excited with UV light to cause luminescence of the complex. The luminescence is detected and characteristics of the luminescence spectra are used to determine the presence of chlorinated compounds and also the quantity of the chlorine in the compounds

Enhanced photo-activated luminescence for screening polychlorobiphenyls (PCBs) and other related chlorinated compounds

DOEpatents

Vo-Dinh, Tuan

1993-01-01

The presence of polychlorinated biphenyls and other chlorinated compounds in a sample is determined by treating the sample with a photo-activator and then exposing the treated sample to a UV light source. The UV light produces a photo-product complex, which is subsequently excited with UV light to cause luminescence of the complex. The luminescence is detected and characteristics of the luminescence spectra are used to determine the presence of chlorinated compounds and also the quantity of the chlorine in the compounds.

Enhanced photo-activated luminescence for screening polychlorobiphenyls (PCBs) and other related chlorinated compounds

DOEpatents

Vo-Dinh, T.

1994-06-07

The presence of polychlorinated biphenyls and other chlorinated compounds in a sample is determined by treating the sample with a photo-activator and then exposing the treated sample to a UV light source. The UV light produces a photo-product complex, which is subsequently excited with UV light to cause luminescence of the complex. The luminescence is detected and characteristics of the luminescence spectra are used to determine the presence of chlorinated compounds and also the quantity of the chlorine in the compounds. 14 figs.

Enhanced photo-activated luminescence for screening polychlorobiphenyls (PCBs) and other related chlorinated compounds

DOEpatents

Tuan Vodinh.

1993-12-21

The presence of polychlorinated biphenyls and other chlorinated compounds in a sample is determined by treating the sample with a photo-activator and then exposing the treated sample to a UV light source. The UV light produces a photo-product complex, which is subsequently excited with UV light to cause luminescence of the complex. The luminescence is detected and characteristics of the luminescence spectra are used to determine the presence of chlorinated compounds and also the quantity of the chlorine in the compounds. 14 figures.

Chlorinated ethenes from groundwater in tree trunks

USGS Publications Warehouse

Vroblesky, Don A.; Nietch, C.T.; Morris, J.T.

1999-01-01

The purpose of this investigation was to determine whether tree-core analysis could be used to delineate shallow groundwater contamination by chlorinated ethenes. Analysis of tree cores from bald cypress [Taxodium distichum (L.) Rich], tupelo (Nyssa aquatica L.), sweet gum (Liquidambar stryaciflua L.), oak (Quercus spp.), sycamore (Platanus occidentalis L.), and loblolly pine (Pinus taeda L.) growing over shallow groundwater contaminated with cis-1,2-dichloroethene (cDCE) and trichloroethene (TCE) showed that those compounds also were present in the trees. The cores were collected and analyzed by headspace gas chromatography. Bald cypress, tupelo, and loblolly pine contained the highest concentrations of TCE, with lesser amounts in nearby oak and sweet gum. The concentrations of cDCE and TCE in various trees appeared to reflect the configuration of the chlorinated-solvent groundwater contamination plume. Bald cypress cores collected along 18.6-m vertical transects of the same trunks showed that TCE concentrations decline by 30−70% with trunk height. The ability of the tested trees to take up cDCE and TCE make tree coring a potentially cost-effective and simple approach to optimizing well placement at this site. 

FY90 R&D Project Descriptions ESL (Engineering & Services Laboratory) Environics Division

DTIC Science & Technology

1989-07-01

and Development Support for Subsurface Monitoring Technology 15 19007048 Pumping and Purging Contaminants 16 19007049 Methods for Selecting In Situ...Decontamination 40 3788VW17 Treatment of Chlorinated Organics with Aboveground Bioreactors 41 3788VW18 Improved Methods for Monitoring Fuel Biodegradation 42 2...Fluoride (HF) Dispersion Model 63 21036093 Solvent Capacity Field Test Method 64 21037097 Volatile Organic Compound (VOC) Control Technology 65 21037102

PREMChlor: Probabilistic Remediation Evaluation Model for Chlorinated Solvents

DTIC Science & Technology

2010-03-01

Council O&M Operation & Management PAT pump-and-treat PCE tetrachloroethylene PDFs Probability density functions PRBs Permeable reactive barriers...includes a one-time capital cost and a total operation & management (O&M) cost in present net value (NPV) for a certain remediation period. The...Generally, the costs of plume treatment include the capital cost (treatment volume multiply by the unit cost) and the annual operation & Management (O&M

Diagnostic Tools for Performance Evaluation of Innovative In-Situ Remediation Technologies at Chlorinated Solvent-Contaminated Sites

DTIC Science & Technology

2011-07-01

fluid resistivity , temperature logging, and flow metering at other sites that typically indicated only two or three active fractures in each hole...was consistent with results of conventional borehole fluid resistivity , temperature logging, and flow metering at other sites that typically indicated...following tests were performed in each boundary monitoring well: ■ Gamma Ray; ■ Spontaneous Potential (SP); ■ Single Point Resistance (SPR

Edible Oil Barriers for Treatment of Chlorinated Solvent and Perchlorate-Contaminated Groundwater

DTIC Science & Technology

2010-02-01

This page left blank intentionally. 9 3.0 TECHNOLOGY The emulsified oil technology is a low- cost process for delivering a low solubility, slowly...associated with the actual injection process , including costs for installing the injection and monitoring wells, purchasing the substrate for injection...large area can be significantly lower due to economies of scale during injection and the relatively lower design, permitting, and monitoring costs

Monitoring the effect of poplar trees on petroleum-hydrocarbon and chlorinated-solvent contaminated ground water

USGS Publications Warehouse

Landmeyer, James E.

2001-01-01

At contaminated groundwater sites, poplar trees can be used to affect ground-water levels, flow directions, and ultimately total groundwater and contaminant flux to areas downgradient of the trees. The magnitude of the hydrologic changes can be monitored using fundamental concepts of groundwater hydrology, in addition to plant physiology-based approaches, and can be viewed as being almost independent of the contaminant released. The affect of poplar trees on the fate of groundwater contaminants, however, is contaminant dependent. Some petroleum hydrocarbons or chlorinated solvents may be mineralized or transformed to innocuous compounds by rhizospheric bacteria associated with the tree roots, mineralized or transformed by plant tissues in the transpiration stream or leaves after uptake, or passively volatilized and rapidly dispersed or oxidized in the atmosphere. These processes also can be monitored using a combination of physiological- or geochemical-based field or laboratory approaches. When combined, such hydrologic and contaminant monitoring approaches can result in a more accurate assessment of the use of poplar trees to meet regulatory goals at contaminated groundwater sites, verify that these goals continue to be met in the future, and ultimately lead to a consensus on how the performance of plant-based remedial strategies (phytoremediation) is to be assessed.

Sustainable in-well vapor stripping: A design, analytical model, and pilot study for groundwater remediation.

PubMed

Sutton, Patrick T; Ginn, Timothy R

2014-12-15

A sustainable in-well vapor stripping system is designed as a cost-effective alternative for remediation of shallow chlorinated solvent groundwater plumes. A solar-powered air compressor is used to inject air bubbles into a monitoring well to strip volatile organic compounds from a liquid to vapor phase while simultaneously inducing groundwater circulation around the well screen. An analytical model of the remediation process is developed to estimate contaminant mass flow and removal rates. The model was calibrated based on a one-day pilot study conducted in an existing monitoring well at a former dry cleaning site. According to the model, induced groundwater circulation at the study site increased the contaminant mass flow rate into the well by approximately two orders of magnitude relative to ambient conditions. Modeled estimates for 5h of pulsed air injection per day at the pilot study site indicated that the average effluent concentrations of dissolved tetrachloroethylene and trichloroethylene can be reduced by over 90% relative to the ambient concentrations. The results indicate that the system could be used cost-effectively as either a single- or multi-well point technology to substantially reduce the mass of dissolved chlorinated solvents in groundwater. Copyright © 2014 Elsevier B.V. All rights reserved.

Contamination source review for Building E5485, Edgewood Area, Aberdeen Proving Ground, Maryland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Billmark, K.A.; Hayes, D.C.; Draugelis, A.K.

1995-09-01

This report was prepared by Argonne National Laboratory (ANL) to document the results of a contamination source review of Building E5485 at the Aberdeen Proving Ground (APG) in Maryland. This report may be used to assist the US Army in planning for the future use or disposition of this building. The review included a historical records search, physical inspection, photographic documentation, geophysical investigation, and collection of air samples. Building E5485 (APG designation) is located in the drainage basin of the west branch of Canal Creek in the Edgewood Area of APG. The building was constructed in 1922 and used asmore » a fan house for agent operations in Building E5487 from 1925 to 1966. Building E5485 was then used as a laboratory to support manufacturing and storage of flammable agents and chemical warfare agents from 1966 until 1967, when it was placed on the inactive list. Air quality samples were collected upwind, downwind, and inside Building E5485 in November 1994. Analytical results showed no distinguishable difference in hydrocarbon and chlorinated solvent levels between the two background samples and the sample collected inside Building E5485. These results indicate that Building E5485 is not a source of volatile organic compound contamination.« less

NDMA formation during chlorination and chloramination of aqueous diuron solutions.

PubMed

Chen, Wei-Hsiang; Young, Thomas M

2008-02-15

Formation of the potent carcinogen N-nitrosodimethylamine (NDMA) during chlorine disinfection of water containing secondary amines is now generally acknowledged. The phenylurea herbicide diuron is one of the most widely used herbicides in California, has been frequently detected in California's water sources with a transient nature of appearance, and has a structure that suggests it might be an NDMA precursor. This study sought to quantify the potential for NDMA formation from aqueous diuron solutions under varied chlorine and chloramine conditions. NDMA formation was consistently observed even in the absence of added ammonia, which has usually been the source of the nitroso-nitrogen during chloramination of other precursors. It appears that both nitrogen atoms in NDMA are donated by diuron during chlorination in the absence of added ammonia. For a given chlorine and diuron dose, NDMA formation increased in the order OCl- < NH2Cl < NHCl2, a result consistentwith previous NDMAformation studies. Significant quantities of NDMA (170 ng/L) were produced during dichloramination of diuron using a low dichloramine concentration and a diuron concentration at the upper end of typically detected concentrations in California (20 microg/L), suggesting a need for further investigation to accurately assess the human health risks posed by diuron with respect to NDMA formation potential. A reaction pathway is proposed to provide a possible explanation for NDMA formation from diuron during chlorination or chloramination. The findings in this study identify a specific potential precursor of NDMA formation, one that arises from nonpoint sources. This further highlights the difficulties associated with determining the environmental safety of chemicals and their associated byproducts.

Environmental Survey of Drinking Water Sources in Kampala, Uganda, during a Typhoid Fever Outbreak

PubMed Central

Kahler, A. M.; Nansubuga, I.; Nanyunja, E. M.; Kaplan, B.; Jothikumar, N.; Routh, J.; Gómez, G. A.; Mintz, E. D.; Hill, V. R.

2017-01-01

ABSTRACT In 2015, a typhoid fever outbreak began in downtown Kampala, Uganda, and spread into adjacent districts. In response, an environmental survey of drinking water source types was conducted in areas of the city with high case numbers. A total of 122 samples was collected from 12 source types and tested for Escherichia coli, free chlorine, and conductivity. An additional 37 grab samples from seven source types and 16 paired large volume (20 liter) samples from wells and springs were also collected and tested for the presence of Salmonella enterica serovar Typhi. Escherichia coli was detected in 60% of kaveras (drinking water sold in plastic bags) and 80% of refilled water bottles; free chlorine was not detected in either source type. Most jerry cans (68%) contained E. coli and had free chlorine residuals below the WHO-recommended level of 0.5 mg/liter during outbreaks. Elevated conductivity readings for kaveras, refilled water bottles, and jerry cans (compared to treated surface water supplied by the water utility) suggested that they likely contained untreated groundwater. All unprotected springs and wells and more than 60% of protected springs contained E. coli. Water samples collected from the water utility were found to have acceptable free chlorine levels and no detectable E. coli. While S. Typhi was not detected in water samples, Salmonella spp. were detected in samples from two unprotected springs, one protected spring, and one refilled water bottle. These data provided clear evidence that unregulated vended water and groundwater represented a risk for typhoid transmission. IMPORTANCE Despite the high incidence of typhoid fever globally, relatively few outbreak investigations incorporate drinking water testing. During waterborne disease outbreaks, measurement of physical-chemical parameters, such as free chlorine residual and electrical conductivity, and of microbiological parameters, such as the presence of E. coli or the implicated etiologic agent, in drinking water samples can identify contaminated sources. This investigation indicated that unregulated vended water and groundwater sources were contaminated and were therefore a risk to consumers during the 2015 typhoid fever outbreak in Kampala. Identification of contaminated drinking water sources and sources that do not contain adequate disinfectant levels can lead to rapid targeted interventions. PMID:28970225

Role of drinking water biofilms on residual chlorine decay and trihalomethane formation: An experimental and modeling study.

PubMed

Xu, Jianeng; Huang, Conghui; Shi, Xiaoyang; Dong, Shengkun; Yuan, Baoling; Nguyen, Thanh H

2018-06-13

PVC pipe loops were constructed to simulate household premise plumbing. These pipe loops were exposed to water treated by physical processes at three water treatment plants in Xiamen, China from August 2016 to June 2017. After the biofilms were allowed to develop inside the pipes, these pipes were deconstructed and exposed to organic-free chlorine solution buffered at pH 6.8 ± 0.2 for 48 h. The decay of chlorine by these biofilms was higher than by the effluent waters that were used to grow the biofilms. A chlorine consumption mass balance model elucidated the role of both the diffusion of chlorine into the biofilm and the reaction of chlorine with the biofilm matrix. Comparable concentrations of trihalomethanes were quantified from the reaction between chlorine and source water organic matters, and chlorine and the biofilm, further emphasizing the role of biofilms in the safety of disinfected drinking water. These findings imply that when chlorine is used in the drinking water distribution system, the ubiquitous presence of biofilms may cause the depletion of chlorine and the formation of non-negligible levels of toxic disinfection byproducts. Copyright © 2018 Elsevier B.V. All rights reserved.

Effects of Processing on MOS Radiation Hardening

DTIC Science & Technology

1992-09-01

magnitude) impurity inclusion for Fluorine sources vs. Chlorine sources, many of the other beneficial effects on point defects, traps, MOS quality, etc...profiles. The addition of percent concentrations of a chlorine rates from 1 to 10 ml/nmr. This corresponded to fluorine bearing compound to the silicon...computes the partial roethane and gaseous nitrogen trifluoride . The alphatic liq- pres-ures of all the possible species in equilibrium in the uid

Validation of chlorine and oxygen isotope ratio analysis to differentiate perchlorate sources and to document perchlorate biodegradation

USGS Publications Warehouse

Paul B. Hatzinger,; Böhlke, John Karl; Sturchio, Neil C.; Gu, Baohua

2013-01-01

Increased health concerns about perchlorate (ClO4-) during the past decade and subsequent regulatory considerations have generated appreciable interest in source identification. The key objective of the isotopic techniques described in this guidance manual is to provide evidence concerning the origin of ClO4- in soils and groundwater and, more specifically, whether that ClO4- is synthetic or natural. Chlorine and oxygen isotopic analyses of ClO4- provide the primary direct approach whereby different sources of ClO4- can be distinguished from each other. These techniques measure the relative abundances of the stable isotopes of chlorine (37Cl and 35Cl) and oxygen (18O, 17O, and 16O) in ClO4- using isotope-ratio mass spectrometry (IRMS). In addition, the relative abundance of the radioactive chlorine isotope 36Cl is measured using accelerator mass spectrometry (AMS). Taken together, these measurements provide four independent quantities that can be used to distinguish natural and synthetic ClO4- sources, to discriminate different types of natural ClO4-, and to detect ClO4- biodegradation in the environment. Other isotopic, chemical, and geochemical techniques that can be applied in conjunction with isotopic analyses of ClO4- to provide supporting data in forensic studies are also described.

Comparison of chlorine and ammonia concentration field trial data with calculated results from a Gaussian atmospheric transport and dispersion model.

PubMed

Bauer, Timothy J

2013-06-15

The Jack Rabbit Test Program was sponsored in April and May 2010 by the Department of Homeland Security Transportation Security Administration to generate source data for large releases of chlorine and ammonia from transport tanks. In addition to a variety of data types measured at the release location, concentration versus time data was measured using sensors at distances up to 500 m from the tank. Release data were used to create accurate representations of the vapor flux versus time for the ten releases. This study was conducted to determine the importance of source terms and meteorological conditions in predicting downwind concentrations and the accuracy that can be obtained in those predictions. Each source representation was entered into an atmospheric transport and dispersion model using simplifying assumptions regarding the source characterization and meteorological conditions, and statistics for cloud duration and concentration at the sensor locations were calculated. A detailed characterization for one of the chlorine releases predicted 37% of concentration values within a factor of two, but cannot be considered representative of all the trials. Predictions of toxic effects at 200 m are relevant to incidents involving 1-ton chlorine tanks commonly used in parts of the United States and internationally. Published by Elsevier B.V.

[Influence of water source switching on water quality in drinking water distribution system].

PubMed

Wang, Yang; Niu, Zhang-bin; Zhang, Xiao-jian; Chen, Chao; He, Wen-jie; Han, Hong-da

2007-10-01

This study investigates the regularity of the change on the physical and chemical water qualities in the distribution system during the process of water source switching in A city. Due to the water source switching, the water quality is chemical-astable. Because of the differences between the two water sources, pH reduced from 7.54 to 7.18, alkalinity reduced from 188 mg x L(-1) to 117 mg x L(-1), chloride (Cl(-)) reduced from 310 mg x L(-1) to 132 mg x L(-1), conductance reduced from 0.176 S x m(-1) to 0.087 S x m(-1) and the ions of calcium and magnesium reduced to 15 mg x L(-1) and 11 mg x L(-1) respectively. Residual chlorine changed while the increase of the chlorine demand and the water quantity decreasing at night, and the changes of pH, alkalinity and residual chlorine brought the iron increased to 0.4 mg x L(-1) at the tiptop, which was over the standard. The influence of the change of the water parameters on the water chemical-stability in the drinking water distribution system is analyzed, and the controlling countermeasure is advanced: increasing pH, using phosphate and enhancing the quality of the water in distribution system especially the residual chlorine.

The Chlorine Isotope Composition of the Solar Nebula & Implications to the Sources of Volatiles to the Terrestrial Planets

NASA Astrophysics Data System (ADS)

Gargano, A. M.; Sharp, Z. D.

2017-12-01

It was originally proposed by Sharp et al., 2016 that the solar nebula was isotopically light based on limited sampling of the Ol-phyric shergottites and two ordinary chondrites (Parnallee LL3.00, and NWA 8276 L3.00). Iron meteorites are remnants of early planetesimals which segregated cores <1Ma after CAI's and have δ37Cl values as low as -7‰, consistent with a light nebular source. Chondrules are relatively younger than iron meteorite parent bodies (2-3Ma after CAI's) and exhibit evidence for mixing with & recycling numerous isotopically distinct precursors as observed by Cl rich chondrules in Semarkona, and Qingzhen. The average δ37Cl values of chondrites are around 0‰, independent of petrologic type or [Cl], suggesting that chondrule forming regions have similar chlorine isotope sources. The average δ37Cl values of chondrites are consistent with a +3 to +6‰ isotopic fractionation of HCl clathrate from HCl gas, which occurred beyond the snow-line at 150K. The recycling of chondritic precursors mixed with HCl clathrate can account for pristine type 3.00 chondrites with δ37Cl values at approximately 0‰ independent of [Cl], or petrologic type. The source of volatiles to the terrestrial planets is commonly assumed to be chondritic in origin. These preliminary chlorine isotope data suggest that early planetesimals and planetary embryos had a solar Cl component at -7‰ or less, and secondary processes has since increased the δ37Cl values of Earth, Mars, and most chondrites. The chlorine isotope system therefore provides a new constraint regarding the sources of volatiles to the terrestrial planets. The δ37Cl value of the bulk Earth is around 0‰, inconsistent with a nebular source as measured in the Martian mantle but similar to that of chondrites with HCl clathrate precursors. The prolonged accretion of heavy chondritic material to Earth can account for the chlorine isotope discrepancy between the Earth and Mars, but is unconstrained by HSE abundances before complete core-mantle differentiation. Here, we examine the amount of chondritic chlorine and water that can added to the Earth allowable by HSE abundances and explore other potential sources of volatiles to the terrestrial planets to account for isotopic and elemental discrepancies.

The formation and fate of chlorinated organic substances in temperate and boreal forest soils.

PubMed

Clarke, Nicholas; Fuksová, Kvetoslava; Gryndler, Milan; Lachmanová, Zora; Liste, Hans-Holger; Rohlenová, Jana; Schroll, Reiner; Schröder, Peter; Matucha, Miroslav

2009-03-01

Chlorine is an abundant element, commonly occurring in nature either as chloride ions or as chlorinated organic compounds (OCls). Chlorinated organic substances were long considered purely anthropogenic products; however, they are, in addition, a commonly occurring and important part of natural ecosystems. Formation of OCls may affect the degradation of soil organic matter (SOM) and thus the carbon cycle with implications for the ability of forest soils to sequester carbon, whilst the occurrence of potentially toxic OCls in groundwater aquifers is of concern with regard to water quality. It is thus important to understand the biogeochemical cycle of chlorine, both inorganic and organic, to get information about the relevant processes in the forest ecosystem and the effects on these from human activities, including forestry practices. A survey is given of processes in the soil of temperate and boreal forests, predominantly in Europe, including the participation of chlorine, and gaps in knowledge and the need for further work are discussed. Chlorine is present as chloride ion and/or OCls in all compartments of temperate and boreal forest ecosystems. It contributes to the degradation of SOM, thus also affecting carbon sequestration in the forest soil. The most important source of chloride to coastal forest ecosystems is sea salt deposition, and volcanoes and coal burning can also be important sources. Locally, de-icing salt can be an important chloride input near major roads. In addition, anthropogenic sources of OCls are manifold. However, results also indicate the formation of chlorinated organics by microorganisms as an important source, together with natural abiotic formation. In fact, the soil pool of OCls seems to be a result of the balance between chlorination and degradation processes. Ecologically, organochlorines may function as antibiotics, signal substances and energy equivalents, in descending order of significance. Forest management practices can affect the chlorine cycle, although little is at present known about how. The present data on the apparently considerable size of the pool of OCls indicate its importance for the functioning of the forest soil system and its stability, but factors controlling their formation, degradation and transport are not clearly understood. It would be useful to estimate the significance and rates of key processes to be able to judge the importance of OCls in SOM and litter degradation. Effects of forest management processes affecting SOM and chloride deposition are likely to affect OCls as well. Further standardisation and harmonisation of sampling and analytical procedures is necessary. More work is necessary in order to understand and, if necessary, develop strategies for mitigating the environmental impact of OCls in temperate and boreal forest soils. This includes both intensified research, especially to understand the key processes of formation and degradation of chlorinated compounds, and monitoring of the substances in question in forest ecosystems. It is also important to understand the effect of various forest management techniques on OCls, as management can be used to produce desired effects.

Sorption/Desorption and Transport of Trichloroethene in Freshly-amended, Synthetically- aged, and Field-contaminated Aquifer Material

NASA Astrophysics Data System (ADS)

Johnson, G. R.; Norris, D. K.; Brusseau, M. L.

2008-12-01

This study investigates the effect of long-term contaminant aging on the sorption/desorption and transport of trichloroethene in a low organic-carbon content aquifer material collected from the source zone of a chlorinated-solvent contaminated federal Superfund site in Arizona. This was accomplished by comparing elution behavior for field-contaminated, synthetically-aged (contact times of approximately four years), and freshly-amended aquifer material. Elution of trichloroethene exhibited extensive low-concentration tailing, despite minimal retention of trichloroethene by the aquifer material. The observed nonideal behavior indicates significant mass-transfer constraints influenced trichloroethene transport in this aquifer material. The elution behavior of trichloroethene for the field-contaminated and aged treatments was essentially identical to that observed for the fresh treatments. In addition, the results of three independent mass- balance analyses, total mass eluted, solvent-extraction analysis of residual sorbed mass, and flow- interruption rebound, showed equivalent recoveries for the aged and fresh treatments. These results indicate that long-term contaminant aging did not significantly influence the transport and fate behavior of trichloroethene in this low organic-carbon aquifer material. The observed nonideal behavior of trichloroethene (i.e., nonlinear sorption and significantly rate-limited sorption/desorption) suggests physically condensed carbonaceous material, comprising 61% of this media's organic-carbon content, mediates the transport and fate behavior of trichloroethene in this low organic-carbon content aquifer material.

Photocatalytic destruction of chlorinated solvents with solar energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacheco, J.; Prairie, M.; Yellowhorse, L.

1990-01-01

Sandia National Laboratories and the Solar Energy Research Institute are developing a photocatalytic process to destroy organic contaminants in water. Tests with common water pollutants are being conducted at Sandia's Solar Thermal Test Facility using a near commercial-scale single-axis tracking parabolic trough system with glass pipe mounted at its focus. Experiments at this scale provide verification of laboratory studies and allow examination of design and operation issues at a real-life scale. The catalyst, titanium dioxide (TiO{sub 2}), is a harmless material found in paint, cosmetics and toothpaste. Experiments were conducted to determine the effect of key process parameters on destructionmore » rates of two chlorinated organic compounds which are common water pollutants: trichloroethylene and trichloroethane. In this paper, we summarize the engineering-scale results of these experiments and analyses. 21 refs., 8 figs.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morita, M.

Chlorinated benzenes are composed of twelve chemical species: one mono-, three di-, three tri-, three tetra-, one penta-, and one hexachlorobenzene. Most of these are not only important intermediates for various kinds of chemicals but are also extensively employed for various applications singly or in combination. For example, 1,4-dichlorobenzene is used chiefly against termites in soil; trichlorobenzenes are used as solvents for pesticides and also as heat transfer agents with PCBs; the mixture of trichlorobenzene and tetrachlorobenzene is applied in controlling shellfish predators; and hexachlorobenzene is applied to wheat as a fungicide in some countries and as an additive tomore » rubber products. The annual production (1973) of monochlorobenzene, 1,2-dichlorobenzene, and 1,4-dichlorobenzene in Japan was about 23,000, 9000, and 20,000, tons, respectively. Production volumes of other chlorinated benzenes are not well known but are assumed to be smaller than those of the above three compounds. The total annual production of chlorinated benzenes far surpasses the peak production of PCBs (7000 tons/year) which are known as a ubiquitous pollutant in this country. Since chlorinated benzenes have a chemical structure and properties similar to those of PCBs and PCTs, it seemed necessary to direct our attention to environmental contamination by these materials. The present paper describes only the occurrence and the fate of these materials. Toxicity and biological impact are not referred to here.« less

Stabile Chlorine Isotope Study of Martian Shergottites and Nakhlites; Whole Rock and Acid Leachates and Residues

NASA Technical Reports Server (NTRS)

Nakamura, N.; Nyquist, L. E.; Reese, Y.; Shih, C-Y; Fujitani, T.; Okano, O.

2011-01-01

We have established a precise analytical technique for stable chlorine isotope measurements of tiny planetary materials by TIMS (Thermal Ionization Mass Spectrometry) [1], for which the results are basically consistent with the IRMS tech-nique (gas source mass spectrometry) [2,3,4]. We present here results for Martian shergottites and nakhlites; whole rocks, HNO3-leachates and residues, and discuss the chlorine isotope evolution of planetary Mars.

Diagnostic Tools for Performance Evaluation of Innovative In-Situ Remediation Technologies at Chlorinated Solvent-Contaminated Sites

DTIC Science & Technology

2011-07-01

to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT...these innovative methods with conventional diagnostic tools that are currently used for assessing bioremediation performance. 132 Rula Deeb (510) 596...conventional diagnostic tools that are currently used for assessing bioremediation performance. DEMONSTRATION RESULTS 3-D multi-level systems

Development of Azeotropic Blends to Replace TCE and nPB in Vapor Degreasing Operations

DTIC Science & Technology

2016-12-21

vapor zone is fully contained and oxygen free, inexpensive and effective flammable solvents may be used. Working toward this type of process change...chlorine, chromic acid etc.) 7.2. Conditions for safe storage including any incompatibilities Store in a well- ventilated place. Store at temperatures ...Nausea, Dizziness, Headache, Exposure to and/or consumption of alcohol may increase toxic effects . To the best of our knowledge, the chemical

Engineered Approaches to In Situ Bioremediation of Chlorinated Solvents: Fundamentals and Field Applications

DTIC Science & Technology

2000-07-01

scale system that consists of three injection wells currently is being installed at the site. The wells will deliver fructose corn syrup to the...aerobic reaction). The energy gained is stored as high energy compounds, such as ATP and low- energy compounds, such as nicotinamide adenine...processes at high redox potential values is limited; efficiency improves as the redox potential decreases. Pilot studies have been conducted at a variety of

Crude oil desulfurization

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Hsu, G. C.; Ernest, J. B. (Inventor)

1982-01-01

High sulfur crude oil is desulfurized by a low temperature (25-80 C.) chlorinolysis at ambient pressure in the absence of organic solvent or diluent but in the presence of water (water/oil=0.3) followed by a water and caustic wash to remove sulfur and chlorine containing reaction products. The process described can be practiced at a well site for the recovery of desulfurized oil used to generate steam for injection into the well for enhanced oil recovery.

Inkjet Printing of Organic Light-Emitting Diodes Based on Alcohol-Soluble Polyfluorenes

NASA Astrophysics Data System (ADS)

Odod, A. V.; Gadirov, R. M.; Solodova, T. A.; Kurtsevich, A. E.; Il'gach, D. M.; Yakimanskii, A. V.; Burtman, V.; Kopylova, T. N.

2018-04-01

Ink compositions for inkjet printing based on poly(9.9-dioctylfluorene) and its alcohol-soluble analog are created. Current-voltage, brightness-voltage, and spectral characteristics are compared for one- and twolayer polymer structures of organic light-emitting diodes. It is shown that the efficiency of the alcohol-soluble polyfluorene analog is higher compared to poly(9.9-dioctylfluorene), and the possibility of viscosity optimization is higher compared to aromatic chlorinated solvents.

Multiple source/multiple target fluid transfer apparatus

DOEpatents

Turner, Terry D.

1997-01-01

A fluid transfer apparatus includes: a) a plurality of orifices for connection with fluid sources; b) a plurality of orifices for connection with fluid targets; c) a set of fluid source conduits and fluid target conduits associated with the orifices; d) a pump fluidically interposed between the source and target conduits to transfer fluid therebetween; e) a purge gas conduit in fluid communication with the fluid source conduits, fluid target conduits and pump to receive and pass a purge gas under pressure; f) a solvent conduit in fluid communication with the fluid source conduits, fluid target conduits and pump to receive and pass solvent, the solvent conduit including a solvent valve; g) pump control means for controlling operation of the pump; h) purge gas valve control means for controlling operation of the purge gas valve to selectively impart flow of purge gas to the fluid source conduits, fluid target conduits and pump; i) solvent valve control means for controlling operation of the solvent valve to selectively impart flow of solvent to the fluid source conduits, fluid target conduits and pump; and j) source and target valve control means for controlling operation of the fluid source conduit valves and the fluid target conduit valves to selectively impart passage of fluid between a selected one of the fluid source conduits and a selected one of the fluid target conduits through the pump and to enable passage of solvent or purge gas through selected fluid source conduits and selected fluid target conduits.

Multiple source/multiple target fluid transfer apparatus

DOEpatents

Turner, T.D.

1997-08-26

A fluid transfer apparatus includes: (a) a plurality of orifices for connection with fluid sources; (b) a plurality of orifices for connection with fluid targets; (c) a set of fluid source conduits and fluid target conduits associated with the orifices; (d) a pump fluidically interposed between the source and target conduits to transfer fluid there between; (e) a purge gas conduit in fluid communication with the fluid source conduits, fluid target conduits and pump to receive and pass a purge gas under pressure; (f) a solvent conduit in fluid communication with the fluid source conduits, fluid target conduits and pump to receive and pass solvent, the solvent conduit including a solvent valve; (g) pump control means for controlling operation of the pump; (h) purge gas valve control means for controlling operation of the purge gas valve to selectively impart flow of purge gas to the fluid source conduits, fluid target conduits and pump; (i) solvent valve control means for controlling operation of the solvent valve to selectively impart flow of solvent to the fluid source conduits, fluid target conduits and pump; and (j) source and target valve control means for controlling operation of the fluid source conduit valves and the fluid target conduit valves to selectively impart passage of fluid between a selected one of the fluid source conduits and a selected one of the fluid target conduits through the pump and to enable passage of solvent or purge gas through selected fluid source conduits and selected fluid target conduits. 6 figs.

Residual contamination and corrosion on electrochemically marked uranium

NASA Astrophysics Data System (ADS)

Seals, R. D.; Bullock, J. S.; Cristy, S. S.; Bennett, R. K.

Residual contamination and potential corrosion problems on uranium parts electrochemically marked with PHB-1 and PHB-1E electroetchants have been investigated using ion microprobe mass analysis (IMMA), scanning electron microscopy (SEM), and light microscopy (LM). The effectiveness of various solvent-cleaning sequences and the influence of the use of an abrasive cleaner were evaluated. The corrosion depths and chlorine distributions resulting from the electroetching process were determined. To meet the objective, the surfaces of uranium coupons, which had been processed according to production procedures for parts, i.e., machining, cleaning, marking, inspecting and coating with Shell Vitrea-29® oil, were studied. The greater surface wetting capability of the PHB-1E electroetchant solution relative to PHB-1 resulted in less localized corrosion at the point of attack which provided a more legible mark. Components of the electroetchants (aluminum, potassium and chromium) were found in the marked areas of both types of electroetched samples. Chromium, resulting from the corrosion inhibitor in the electroetchants, was found in the etched areas as well as on the coupon away from the electroetched areas. Depth profile data indicated that the major etching action (marking thickness) of the electroetchants penetrated to a depth of approximately 200 nm. Trace amounts of chlorine were present primarily within the first 65 nm of the marked surface. Comparison of the solvent rinsing sequences revealed that the most effective cleaning process included a degreaser, such as perchloroethylene, followed by a polar solvent, such as alcohol. Evaluation of the use of an abrasive cleaner on the electroetched areas indicates that this process removed residual contaminants, increased mark legibility and did not introduce significant residuals from the abrading material or cause significant surface damage.

Ultraviolet-B radiation enhancement in dielectric barrier discharge based xenon chloride exciplex source by air

NASA Astrophysics Data System (ADS)

Gulati, P.; Prakash, R.; Pal, U. N.; Kumar, M.; Vyas, V.

2014-07-01

A single barrier dielectric barrier discharge tube of quartz with multi-strip Titanium-Gold (Ti-Au) coatings have been developed and utilized for ultraviolet-B (UV-B) radiation production peaking at wavelength 308 nm. The observed radiation at this wavelength has been examined for the mixtures of the Xenon together with chlorine and air admixtures. The gas mixture composition, chlorine gas content, total gas pressure, and air pressure dependency of the UV intensity, has been analyzed. It is found that the larger concentration of Cl2 deteriorates the performance of the developed source and around 2% Cl2 in this source produced optimum results. Furthermore, an addition of air in the xenon and chlorine working gas environment leads to achieve same intensity of UV-B light but at lower working gas pressure where significant amount of gas is air.

Ultraviolet-B radiation enhancement in dielectric barrier discharge based xenon chloride exciplex source by air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gulati, P., E-mail: pgulati1512@gmail.com; Department of Physics, Banasthali University, P.O. Banasthali Vidyapith, Rajasthan 304022; Prakash, R.

2014-07-07

A single barrier dielectric barrier discharge tube of quartz with multi-strip Titanium-Gold (Ti-Au) coatings have been developed and utilized for ultraviolet-B (UV-B) radiation production peaking at wavelength 308 nm. The observed radiation at this wavelength has been examined for the mixtures of the Xenon together with chlorine and air admixtures. The gas mixture composition, chlorine gas content, total gas pressure, and air pressure dependency of the UV intensity, has been analyzed. It is found that the larger concentration of Cl{sub 2} deteriorates the performance of the developed source and around 2% Cl{sub 2} in this source produced optimum results. Furthermore, anmore » addition of air in the xenon and chlorine working gas environment leads to achieve same intensity of UV-B light but at lower working gas pressure where significant amount of gas is air.« less

Analytical solutions for sequentially coupled one-dimensional reactive transport problems Part I: Mathematical derivations

NASA Astrophysics Data System (ADS)

Srinivasan, V.; Clement, T. P.

2008-02-01

Multi-species reactive transport equations coupled through sorption and sequential first-order reactions are commonly used to model sites contaminated with radioactive wastes, chlorinated solvents and nitrogenous species. Although researchers have been attempting to solve various forms of these reactive transport equations for over 50 years, a general closed-form analytical solution to this problem is not available in the published literature. In Part I of this two-part article, we derive a closed-form analytical solution to this problem for spatially-varying initial conditions. The proposed solution procedure employs a combination of Laplace and linear transform methods to uncouple and solve the system of partial differential equations. Two distinct solutions are derived for Dirichlet and Cauchy boundary conditions each with Bateman-type source terms. We organize and present the final solutions in a common format that represents the solutions to both boundary conditions. In addition, we provide the mathematical concepts for deriving the solution within a generic framework that can be used for solving similar transport problems.

Vanadium Chloroperoxidases: The Missing Link in the Formation of Chlorinated Compounds and Chloroform in the Terrestrial Environment?

PubMed

Wever, Ron; Barnett, Phil

2017-08-17

It is well established that the majority of chlorinated organic substances found in the terrestrial environment are produced naturally. The presence of these compounds in soils is not limited to a single ecosystem. Natural chlorination is also a widespread phenomenon in grasslands and agricultural soils typical for unforested areas. These chlorinated compounds are formed from chlorination of natural organic matter consisting of very complex chemical structures, such as lignin. Chlorination of several lignin model compounds results in the intermediate formation of trichloroacetyl-containing compounds, which are also found in soils. These decay, in general, through a haloform-type reaction mechanism to CHCl 3 . Upon release into the atmosphere, CHCl 3 will produce chlorine radicals through photolysis, which will, in turn, lead to natural depletion of ozone. There is evidence that fungal chloroperoxidases able to produce HOCl are involved in the chlorination of natural organic matter. The objective of this review is to clarify the role and source of the various chloroperoxidases involved in the natural formation of CHCl 3 . © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Chlorine in solid fuels fired in pulverized fuel boilers sources, forms, reactions, and consequences: a literature review

DOE Office of Scientific and Technical Information (OSTI.GOV)

David A. Tillman; Dao Duong; Bruce Miller

2009-07-15

Chlorine is a significant source of corrosion and deposition, both from coal and from biomass, and in PF boilers. This investigation was designed to highlight the potential for corrosion risks associated with once-through units and advanced cycles. The research took the form of a detailed literature investigation to evaluate chlorine in solid fuels: coals of various ranks and origins, biomass fuels of a variety of types, petroleum cokes, and blends of the above. The investigation focused upon an extensive literature review of documents dating back to 1991. The focus is strictly corrosion and deposition. To address the deposition and corrosionmore » issues, this review evaluates the following considerations: concentrations of chlorine in available solid fuels including various coals and biomass fuels, forms of chlorine in those fuels, and reactions - including reactivities - of chlorine in such fuels. The assessment includes consideration of alkali metals and alkali earth elements as they react with, and to, the chlorine and other elements (e.g., sulfur) in the fuel and in the gaseous products of combustion. The assessment also includes other factors of combustion: for example, combustion conditions including excess O{sub 2} and combustion temperatures. It also considers analyses conducted at all levels: theoretical calculations, bench scale laboratory data and experiments, pilot plant experiments, and full scale plant experience. Case studies and plant surveys form a significant consideration in this review. The result of this investigation focuses upon the concentrations of chlorine acceptable in coals burned exclusively, in coals burned with biomass, and in biomass cofired with coal. Values are posited based upon type of fuel and combustion technology. Values are also posited based upon both first principles and field experience. 86 refs., 8 figs., 7 tabs.« less

Separation of chlorinated diastereomers of decarboxy-betacyanins in myeloperoxidase catalyzed chlorinated Beta vulgaris L. extract.

PubMed

Wybraniec, Sławomir; Starzak, Karolina; Szneler, Edward; Pietrzkowski, Zbigniew

2016-11-15

A comparative chromatographic evaluation of chlorinated decarboxylated betanins and betanidins generated under activity of hypochlorous acid exerted upon these highly antioxidative potent decarboxylated pigments derived from natural sources was performed by LC-DAD-ESI-MS/MS. Comparison of the chromatographic profiles of the chlorinated pigments revealed two different directions of retention changes in relation to the corresponding substrates. Chlorination of all betacyanins that are decarboxylated at carbon C-17 results in an increase of their retention times. In contrast, all other pigments (the non-decarboxylated betacyanins as well as 2-decarboxy- and 15-decarboxy-derivatives) exhibit lower retention after chlorination. During further chromatographic experiments based upon chemical transformation of the related pigments (decarboxylation and deglucosylation), the compounds' structures were confirmed. The elaborated method for determination of chlorinated pigments enabled analysis of a chlorinated red beet root extract that was submitted to the MPO/H 2 O 2 /Cl - system acting under inflammation-like conditions (pH 5). This indicates a promising possibility for measurement of these chlorinated pigments as indicators of specific inflammatory states wherein betacyanins and decarboxylated betacyanins act as hypochlorite scavengers. Copyright © 2016 Elsevier B.V. All rights reserved.

Detection of explosives using negative ion mobility spectrometry in air based on dopant-assisted thermal ionization.

PubMed

Shahraki, Hassan; Tabrizchi, Mahmoud; Farrokhpor, Hossein

2018-05-26

The ionization source is an essential component of most explosive detectors based on negative ion mobility spectrometry. Conventional ion sources suffer from such inherent limitations as special safety regulations on radioactive sources or generating interfering ions (for non-radioactive sources) such as corona discharge operating in the air. In this study, a new negative ion source is introduced for ion mobility spectrometry that is based on thermal ionization and operates in the air, applicable to explosives detection. Our system consists of a heating filament powered by an isolated power supply connected to negative high voltage. The ionization is assisted by doping chlorinated compounds in the gas phase using chlorinated hydrocarbons in contact with the heating element to yield Cl - reactant ions. Several chlorinated hydrocarbons are evaluated as the reagent chemicals for providing Cl- reactant ions, of which CCl 4 is identified as the best ionizing reagent. The ion source is evaluated by recording the ion mobility spectra of common explosives, including TNT, RDX, and PETN in the air. A detection limit of 150 pg is obtained for TNT. Compared to other ionization sources, the new source is found to be low-cost, simple, and long-lived, making it suited to portable explosives detection devices. Copyright © 2018 Elsevier B.V. All rights reserved.

Photochemical modeling of emissions trading of highly reactive volatile organic compounds in Houston, Texas. 2. Incorporation of chlorine emissions.

PubMed

Wang, Linlin; Thompson, Tammy; McDonald-Buller, Elena C; Allen, David T

2007-04-01

As part of the State Implementation Plan for attaining the National Ambient Air Quality Standard for ozone, the Texas Commission of Environmental Quality has created a Highly Reactive Volatile Organic Compounds (HRVOC) Emissions Cap and Trade Program for industrial point sources in the Houston/Galveston/Brazoria area. This series of papers examines the potential air quality impacts of this new emission trading program through photochemical modeling of potential trading scenarios; this paper examines the air quality impact of allowing facilities to trade chlorine emission reductions for HRVOC allocations on a reactivity weighted basis. The simulations indicate that trading of anthropogenic chlorine emission reductions for HRVOC allowances at a single facility or between facilities, in general, resulted in improvements in air quality. Decreases in peak 1-h averaged and 8-h averaged ozone concentrations associated with trading chlorine emissions for HRVOC allocations on a Maximum Incremental Reactivity (MIR) basis were up to 0.74 ppb (0.63%) and 0.56 ppb (0.61%), respectively. Air quality metrics based on population exposure decreased by up to 3.3% and 4.1% for 1-h and 8-h averaged concentrations. These changes are small compared to the maximum changes in ozone concentrations due to the VOC emissions from these sources (5-10 ppb for 8-h averages; up to 30 ppb for 1-h averages) and the chlorine emissions from the sources (5-10 ppb for maximum concentrations over wide areas and up to 70 ppb in localized areas). The simulations indicate that the inclusion of chlorine emissions in the trading program is likely to be beneficial to air quality and is unlikely to cause localized increases in ozone concentrations ("hot spots").

Effect of peracetic acid, ultraviolet radiation, nanofiltration-chlorine in the disinfection of a non conventional source of water (Tula Valley).

PubMed

Trujillo, J; Barrios, J A; Jimenez, B

2008-01-01

Water supply for human consumption requires certain quality that reduces health risks to consumers. In this sense, the process of disinfection plays an important role in the elimination of pathogenic microorganisms. Even though chlorination is the most applied process based on its effectiveness and cost, its application is being questioned considering the formation of disinfection by-products (DBPs). Therefore, alternative disinfectants are being evaluated and some treatment processes have been proposed to remove DBPs precursors (organic matter. This paper reports the results of disinfection of a non conventional source of water (aquifer recharged unintentionally with raw wastewater) with peracetic acid (PAA) and ultraviolet radiation (UV) as well as nanofiltration (NF) followed by chlorination to produce safe drinking water. The results showed that a dose of 2 mg/L PAA was needed to eliminate total and faecal coliforms. For UV light, a dose of 12.40 mWs/cm2 reduced total and faecal coliforms below the detection limit. On the other hand, chlorine demand of water before NF was 1.1-1.3 mg/L with a trihalomethane formation potential (THMFP) of 118.62 microg/L, in contrast with chlorination after NF where the demand was 0.5 mg/L and THMFP of 17.64 microg/L. The recommended scheme is nanofiltration + chlorination.

Solvent exposure and cognitive function in automotive technicians.

PubMed

Bates, Michael N; Reed, Bruce R; Liu, Sa; Eisen, Ellen A; Hammond, S Katharine

2016-12-01

Automotive technicians are commonly exposed to organic and chlorinated solvents, particularly through use of cleaning products. Occupational solvent exposures have been associated with deficits in cognitive function but, to our knowledge, no previous studies have investigated automotive technicians. The purpose of the present study was to investigate whether previous exposures to n-hexane, in particular, or general solvents posed a persistent neurotoxic hazard to automotive workers. Enrolled in the study were 830 San Francisco Bay Area automotive repair workers. Each participant underwent a battery of cognitive function tests to investigate central nervous system impairment, with a primary focus on the domains of psychomotor speed, fine motor function, memory and mood. Cognitive test results regressed against estimated hexane and total solvent exposures showed little evidence of associations. Exposures to both solvents and hexane were well below the occupational exposure limits. Our results provide some reassurance about persistent neuropsychological effects in automotive workers who use solvent-based products and those who previously used hexane-containing automotive cleaning products, since this solvent is believed no longer to be used in automotive cleaning products. The lack of observed effect in this study may be attributable to low exposures, or it may reflect improved cognitive function since hexane use in automotive cleaning products was discontinued. However, impacts on results of exposure misclassification and/or the healthy worker survivor effect cannot be discounted. Irrespective of the outcome of this study, the main known neurologic effect of n-hexane is peripheral neuropathy, and such an association in automotive technicians is not excluded by these results. Copyright © 2016 Elsevier B.V. All rights reserved.

Assessing Subsurface Bioaugmentation of a Mixed Culture Capable of Chlorinated Solvent Cometabolism via Molecular Methods

NASA Astrophysics Data System (ADS)

Dolan, M. E.; Lim, H. K.; Semprini, L.; Giovanonni, S.; Vergin, K.; McCarty, P. L.; Hopkins, G. D.

2001-12-01

The goal of this project is the successful bioaugmentation of a mixed culture capable of aerobic cometabolism of chlorinated solvent mixtures into an aquifer test zone at Moffett Federal Airfield, CA (Moffett). The test zone consists of two parallel well legs both fed butane and oxygen. One leg will be bioaugmented and the other will serve as an indigenous control. Injection and extraction wells and six (3 per leg) intermediately placed groundwater monitoring points will be frequently monitored for chlorinated solvents, butane, dissolved oxygen, and pH. Groundwater will also be periodically analyzed for microbial content using terminal restriction fragment length polymorphism (T-RFLP) and fluorescence in-situ hybridization (FISH) analyses. In each well leg, two fully-penetrating wells containing solid media will be periodically analyzed for microbial colonization (T-RFLP). The mixed bioaugmentation culture originated from environmental samples taken from Hanford, WA. The culture was enriched on butane and tested for viability in Moffett groundwater and aquifer solids. A clone library was created from the 16S rDNA in the mixed culture and 86 clones were sorted based on RFLP patterns. Complete sequencing of the 16S rDNA gene from the three most prevalent clones revealed 45 clones similar to Acidovorax or Hydrogenophaga, gram negative proteobacterium, and 12 clones similar to Rhodococcus, a gram positive filamentous organism. Fluorescently-labeled rRNA probes were designed for FISH analyses and appropriate restriction enzymes were chosen for T-RFLP analyses based upon the sequence information. Microcosm tests were conducted prior to the initiation of the field study to evaluate butane, 1,1-dichloroethylene (1,1-DCE), and 1,1,1-trichloroethane (TCA) degradation kinetics and microbial community composition. Bioaugmented microcosms began butane utilization sooner than non-bioaugmented ones in the presence and absence of 1,1-DCE, and were able to degrade more 1,1-DCE (up to 500 Yg/L) faster than non-bioaugmented microcosms. T-RFLP analyses of triplicate bottles produced very consistent results. An organism(s) with a T-RFLP signature of 183 bp was found to dominate in bioaugmented microcosms and was consistently absent from non-bioaugmented microcosms. T-RFLP and FISH analyses of groundwater and solid media during the bioaugmentation field demonstration are expected to reveal the extent of transport and subsurface colonization of the bioaugmentation culture.

Natural chlorine and fluorine in the atmosphere, water and precipitation

NASA Technical Reports Server (NTRS)

Friend, James P.

1990-01-01

The geochemical cycles of chlorine and fluorine are surveyed and summarized as framework for the understanding of the global natural abundances of these species in the atmosphere, water, and precipitation. In the cycles the fluxes into and out of the atmosphere can be balanced within the limits of our knowledge of the natural sources and sinks. Sea salt from the ocean surfaces represent the predominant portion of the source of chlorine. It is also an important source of atmospheric fluorine, but volcanoes are likely to be more important fluorine sources. Dry deposition of sea salt returns about 85 percent of the salt released there. Precipitation removes the remainder. Most of the sea salt materials are considered to be cyclic, moving through sea spray over the oceans and either directly back to the oceans or deposited dry and in precipitation on land, whence it runs off into rivers and streams and returns to the oceans. Most of the natural chlorine in the atmosphere is in the form of particulate chloride ion with lesser amounts as gaseous inorganic chloride and methyl chloride vapor. Fluorine is emitted from volcanoes primarily as HF. It is possible that HF may be released directly form the ocean surface but this has not been confirmed by observation. HCl and most likely HF gases are released into the atmosphere by sea salt aerosols. The mechanism for the release is likely to be the provision of protons from the so-called excess sulfate and HNO3. Sea salt aerosol contains fluorine as F(-), MgF(+), CaF(+), and NaF. The concentrations of the various species of chlorine and fluorine that characterize primarily natural, unpolluted atmospheres are summarized in tables and are discussed in relation to their fluxes through the geochemical cycle.

Comparison of Chlorinated Ethenes DNAPL Reductive Dechlorination by Indigenous and Evanite culture with Surfactant Tween-80

NASA Astrophysics Data System (ADS)

Kwon, S.; Hong, S.; Kim, R.; Kim, N.; Ahn, H.; Lee, S.; Kim, Y.

2010-12-01

Although many innovative technologies have been developed to enhance remediation of chlorinated ethenes(e.g. tetrachloroethene[PCE], trichloroethene[TCE])DNAPL source zones, they have been ineffective in reducing contaminant concentration to regulatory end points. Thus, combination of surfactant flushing process that removes significant contaminant mass with microbial reductive dechlorination, posttreatment "polishing step" to control the remaining DNAPL that may serve as a source of reducing equivalents and stimulate the dechlorinating bacterial communities may be an attractive remediation process alternatively. Microcosm studies were conducted to explore chlorinated ethenes, PCE/TCE of 3 ~ 30 mg/L dechlorination by indigenous microbial communities from TCE DNAPL source zones of Korea and Evanite culture in the presence of Tween-80 of 10 ~ 5,000 mg/L. In the microcosms for indigenous microbial communities, by-products(e.g. c-DCE, vinyl chloride) of reductive dechlorination of PCE/TCE were not detected. This results suggest dechlorinating bacteria might be not exist or high concentration of chlorinated ethenes inhibit activity of dechlorinating bacteria in indigenous microbial communities. But VFAs like acetate, methane and hydrogen gas from fermentation of Tween-80 were detected. So Tween-80 might estimated to serve as a source of reducing equivalents. To evaluate the dechlorinating ability of Evanite-culture, we added Evanite-culture to the microcosms for indigenous bacteria and monitored by-products of reductive dechlorination of PCE/TCE and VFAs and hydrogen gas.

Chlorinated ethenes from groundwater in tree trunks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vroblesky, D.A.; Nietch, C.T.; Morris, J.T.

1999-02-01

The purpose of this investigation was to determine whether tree-core analysis could be used to delineate shallow groundwater contamination by chlorinated ethenes. Analysis of tree cores from bald cypress [Taxodium distichum (L.) Rich], tupelo (Nyssa aquatica L.), sweet gum (Liquidambar stryaciflua L.), oak (Quercus spp.), sycamore (Platanus occidentalis L.), and loblolly pine (Pinus taeda L.) growing over shallow groundwater contaminated with cis-1,2-dichloroethene (cDCE) and trichloroethene (TCE) showed that those compounds also were present in the trees. The cores were collected and analyzed by headspace gas chromatography. Bald cypress, tupelo, and loblolly pine contained the highest concentrations of TCE, with lessermore » amounts in nearby oak and sweet gum. The concentrations of cDCE and TCE in various trees appeared to reflect the configuration of the chlorinated-solvent groundwater contamination plume. Bald cypress cores collected along 18.6-m vertical transects of the same trunks showed that TCE concentrations decline by 30--70% with trunk height. The ability of the tested trees to take up cDCE and TCE make tree coring a potentially cost-effective and simple approach to optimizing well placement at this site.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferrell, Jack R; Ware, Anne E

Two catalytic fast pyrolysis (CFP) oils (bottom/heavy fraction) were analyzed in various solvents that are used in common analytical methods (nuclear magnetic resonance - NMR, gas chromatography - GC, gel permeation chromatography - GPC, thermogravimetric analysis - TGA) for oil characterization and speciation. A more accurate analysis of the CFP oils can be obtained by identification and exploitation of solvent miscibility characteristics. Acetone and tetrahydrofuran can be used to completely solubilize CFP oils for analysis by GC and tetrahydrofuran can be used for traditional organic GPC analysis of the oils. DMSO-d6 can be used to solubilize CFP oils for analysismore » by 13C NMR. The fractionation of oils into solvents that did not completely solubilize the whole oils showed that miscibility can be related to the oil properties. This allows for solvent selection based on physico-chemical properties of the oils. However, based on semi-quantitative comparisons of the GC chromatograms, the organic solvent fractionation schemes did not speciate the oils based on specific analyte type. On the other hand, chlorinated solvents did fractionate the oils based on analyte size to a certain degree. Unfortunately, like raw pyrolysis oil, the matrix of the CFP oils is complicated and is not amenable to simple liquid-liquid extraction (LLE) or solvent fractionation to separate the oils based on the chemical and/or physical properties of individual components. For reliable analyses, for each analytical method used, it is critical that the bio-oil sample is both completely soluble and also not likely to react with the chosen solvent. The adoption of the standardized solvent selection protocols presented here will allow for greater reproducibility of analysis across different users and facilities.« less

Inactivation Kinetics of the Cyanobacterial Toxin Microcystin-LR by Free Chlorine

EPA Science Inventory

Worldwide, the increasing occurrence of toxins produced by cyanobacteria in water bodies used as source waters for drinking water has become an important public health issue. Microcystin-LR is one of the most commonly found cyanotoxins. A detailed evaluation of the free chlorine ...

Environmental Survey of Drinking Water Sources in Kampala, Uganda, during a Typhoid Fever Outbreak.

PubMed

Murphy, J L; Kahler, A M; Nansubuga, I; Nanyunja, E M; Kaplan, B; Jothikumar, N; Routh, J; Gómez, G A; Mintz, E D; Hill, V R

2017-12-01

In 2015, a typhoid fever outbreak began in downtown Kampala, Uganda, and spread into adjacent districts. In response, an environmental survey of drinking water source types was conducted in areas of the city with high case numbers. A total of 122 samples was collected from 12 source types and tested for Escherichia coli , free chlorine, and conductivity. An additional 37 grab samples from seven source types and 16 paired large volume (20 liter) samples from wells and springs were also collected and tested for the presence of Salmonella enterica serovar Typhi. Escherichia coli was detected in 60% of kaveras (drinking water sold in plastic bags) and 80% of refilled water bottles; free chlorine was not detected in either source type. Most jerry cans (68%) contained E. coli and had free chlorine residuals below the WHO-recommended level of 0.5 mg/liter during outbreaks. Elevated conductivity readings for kaveras, refilled water bottles, and jerry cans (compared to treated surface water supplied by the water utility) suggested that they likely contained untreated groundwater. All unprotected springs and wells and more than 60% of protected springs contained E. coli Water samples collected from the water utility were found to have acceptable free chlorine levels and no detectable E. coli While S Typhi was not detected in water samples, Salmonella spp. were detected in samples from two unprotected springs, one protected spring, and one refilled water bottle. These data provided clear evidence that unregulated vended water and groundwater represented a risk for typhoid transmission. IMPORTANCE Despite the high incidence of typhoid fever globally, relatively few outbreak investigations incorporate drinking water testing. During waterborne disease outbreaks, measurement of physical-chemical parameters, such as free chlorine residual and electrical conductivity, and of microbiological parameters, such as the presence of E. coli or the implicated etiologic agent, in drinking water samples can identify contaminated sources. This investigation indicated that unregulated vended water and groundwater sources were contaminated and were therefore a risk to consumers during the 2015 typhoid fever outbreak in Kampala. Identification of contaminated drinking water sources and sources that do not contain adequate disinfectant levels can lead to rapid targeted interventions. Copyright © 2017 American Society for Microbiology.

Application of a source apportionment model in consideration of volatile organic compounds in an urban stream

USGS Publications Warehouse

Asher, W.E.; Luo, W.; Campo, K.W.; Bender, D.A.; Robinson, K.W.; Zogorski, J.S.; Pankow, J.F.

2007-01-01

Position-dependent concentrations of trichloroethylene and methyl-tert-butyl ether are considered for a 2.81-km section of the Aberjona River in Massachusetts, USA. This river flows through Woburn and Winchester (Massachusetts, USA), an area that is highly urbanized, has a long history of industrial activities dating to the early 1800s, and has gained national attention because of contamination from chlorinated solvent compounds in Woburn wells G and H. The river study section is in Winchester and begins approximately five stream kilometers downstream from the Woburn wells superfund site. Approximately 300 toxic release sites are documented in the watershed upstream from the terminus of the study section. The inflow to the river study section is considered one source of contamination. Other sources are the atmosphere, a tributary flow, and groundwater flows entering the river; the latter are categorized according to stream zone (1, 2, 3, etc.). Loss processes considered include outflows to groundwater and water-to-atmosphere transfer of volatile compounds. For both trichloroethylene and methyl-rerf-butyl ether, degradation is neglected over the timescale of interest. Source apportionment fractions with assigned values ??inflow, ??1, ??2, ??3, etc. are tracked by a source apportionment model. The strengths of the groundwater and tributary sources serve as fitting parameters when minimizing a reduced least squares statistic between water concentrations measured during a synoptic study in July 2001 versus predictions from the model. The model fits provide strong evidence of substantial unknown groundwater sources of trichloroethylene and methyl-tert-butyl ether amounting to tens of grams per day of trichloroethylene and methyl-tert-butyl ether in the river along the study section. Modeling in a source apportionment manner can be useful to water quality managers allocating limited resources for remediation and source control. ?? 2007 SETAC.

Integrated Field Scale, Lab Scale, and Modeling Studies for Improving Our Ability to Assess the Groundwater to Indoor Air Pathway at Chlorinated Solvent Impacted Groundwater Sites

DTIC Science & Technology

2016-01-07

clays . The Emean/Estatic values were greater for loam than the other two types of soil – indicating greater amplification of emissions relative to a...ɸT): 0.35 m3-voids/m3- soil Soil permeability to soil gas flow (Kg): 1E-7 cm2 Soil gas phase dynamic viscosity : 1.8E-4 g/cm/s Soil domain

Bioaugmentation for Remediation of Chlorinated Solvents: Technology Development, Status, and Research Needs

DTIC Science & Technology

2005-10-01

Report Documentation Page Form ApprovedOMB No. 0704-0188 Public reporting burden for the collection of information is estimated to average 1 hour...subject to a penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. 1 . REPORT DATE...staff at GeoSyntec, though other vendors and experts have contributed as well. The objectives of this White Paper are to: 1 ) summarize the current

Virantmycin, a new antiviral antibiotic produced by a strain of Streptomyces.

PubMed

Nakagawa, A; Iwai, Y; Hashimoto, H; Miyazaki, N; Oiwa, R; Takahashi, Y; Hirano, A; Shibukawa, N; Kojima, Y; Omura, S

1981-11-01

Virantmycin, a novel chlorine-containing antiviral antibiotic, has been isolated from Streptomyces nitrosporeus No. AM-2722. The active substance in culture broth is isolated as colorless needles by solvent extraction followed by high performance liquid chromatography on silicic acid. The molecular formula is C19H26NO3Cl (molecular weight 351) from the elemental analysis and mass spectrum. The antibiotic possesses antifungal activity and potent inhibitory activity against various RNA and DNA viruses.

Bioenvironmental Engineer’s Guide to TVA-1000B Toxic Vapor Analyzer

DTIC Science & Technology

2014-01-01

chemicals including aromatics, unsaturated chlorinated hydrocarbons, aldehydes , ketones , ethylene oxide, hydrogen sulfide, and glycol ether solvents. The...Dimethoxyethane 9.65 Diethyl ketone 9.32 Ethyl amine 8.86 1,1-Dimethylhydrazine 7.28 Diethyl sulfide 8.43 Ethyl benzene 8.76 1,2-Dibromoethene 9.45...Chemical IP (eV) Chemical IP (eV) Chemical IP (eV) Freon 13 (chlorotrifluoromethane) 12.91 Isobutyric acid 10.02 Methyl butyl ketone 9.34

Monitoring of the aerobe biodegradation of chlorinated organic solvents by stable isotope analysis

NASA Astrophysics Data System (ADS)

Horváth, Anikó; Futó, István; Palcsu, László

2014-05-01

Our chemical-biological basic research aims to eliminate chlorinated environmental contaminants from aquifers around industrial areas in the frame of research program supported by the European Social Fund (TÁMOP-4.2.2.A-11/1/KONV-2012-0043). The most careful and simplest way includes the in situ biodegradation with the help of cultured and compound specific strains. Numerous members of Pseudomonas bacteria are famous about function of bioremediation. They can metabolism the environmental hazardous chemicals like gas oils, dyes, and organic solvents. Our research based on the Pseudomonas putida F1 strain, because its ability to degrade halogenated hydrocarbons such as trichloroethylene. Several methods were investigated to estimate the rate of biodegradation, such as the measurement of the concentration of the pollutant along the contamination pathway, the microcosm's studies or the compound specific stable isotope analysis. In this area in the Transcarpathian basin we are pioneers in the stable isotope monitoring of biodegradation. The main goal is to find stable isotope fractionation factors by stable isotope analysis, which can help us to estimate the rate and effectiveness of the biodegradation. The subsequent research period includes the investigation of the method, testing its feasibility and adaptation in the environment. Last but not least, the research gives an opportunity to identify the producer of the contaminant based on the stable isotope composition of the contaminant.

Determination of the thermal stability of perfluoroalkylethers

NASA Technical Reports Server (NTRS)

Helmick, Larry S.; Jones, William R., Jr.

1990-01-01

The thermal decomposition temperatures of several commercial and custom synthesized perfluoroalkylether fluids were determined with a computerized tensimeter. In general, the decomposition temperatures of the commercial fluids were all similar and significantly higher than those for custom synthesized fluids. Correlation of the decomposition temperatures with the molecular structures of the primary components of the commercial fluids revealed that the stability of the fluids is not affected by intrinsic factors such as carbon chain length, branching, or cumulated difluoroformal groups. Instead, correlation with extrinsic factors revealed that the stability may be limited by the presence of small quantities of thermally unstable material and/or chlorine-containing material arising from the use of chlorine-containing solvents during synthesis. Finally, correlation of decomposition temperatures with molecular weights for Demnum and Krytox fluids supports a chain cleavage reaction mechanism for Demnum fluids and an unzipping reaction mechanism for Krytox fluids.

Coal desulfurization by low temperature chlorinolysis, phase 3

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Rohatgi, N. K.; Ernest, J.

1981-01-01

Laboratory scale, bench scale batch reactor, and minipilot plant tests were conducted on 22 bituminous, subbituminous, and lignite coals. Chemical pretreatment and post treatment of coals relative to the chlorination were tried as a means of enhancing desulfurization by the chlorinolysis process. Elevated temperature (500-700 C) hydrogen treatment of chlorinolysis-processed coal at atmospheric pressure was found to substantially increase coal desulfurization up to 90 percent. Sulfur forms, proximate and ultimate analyses of the processed coal are included. Minipilot plant operation indicates that the continuous flow reactor provides coal desulfurization results comparable to those obtained in the batch reactor. Seven runs were conducted at coal feed rates of 1.5 to 8.8 kg per hour using water and methylchloroform solvents, gaseous chlorine feed of 3 to 31.4 SCFH at 21 to 70 C, and atmospheric pressure for retention times of 20 to 120 minutes.

Formation and reduction of 3-monochloropropane-1,2-diol esters in peanut oil during physical refining.

PubMed

Li, Chang; Li, Linyan; Jia, Hanbing; Wang, Yuting; Shen, Mingyue; Nie, Shaoping; Xie, Mingyong

2016-05-15

In the present study, lab-scale physical refining processes were investigated for their effects on the formation of 3-monochloropropane-1,2-diol (3-MCPD) esters. The potential precursors, partial acylglycerols and chlorines were determined before each refining step. 3-MCPD esters were not detected in degummed and bleached oil when the crude oils were extracted by solvent. While in the hot squeezed crude oils, 3-MCPD esters were detected with low amounts. 3-MCPD esters were generated with maximum values in 1-1.5h at a certain deodorizing temperature (220-260°C). Chlorine seemed to be more effective precursor than partial acylglycerol. By washing bleached oil before deodorization with ethanol solution, the precursors were removed partially and the content of 3-MCPD esters decreased to some extent accordingly. Diacetin was found to reduce 3-MCPD esters effectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Increases in Atmospheric Chlorine from Dichloromethane, a Gas Not Controlled by the Montreal Protocol.

NASA Astrophysics Data System (ADS)

Montzka, S. A.; Hossaini, R.; Hall, B. D.; Hu, L.; Miller, B.; Siso, C.; Andrews, A. E.; Sweeney, C.; Elkins, J. W.; Chipperfield, M.

2015-12-01

Short-lived, anthropogenically produced chlorinated gases historically have not been controlled by the Montreal Protocol; their contribution to stratospheric halogen loading has been relatively small and constant. Since 2000, however, tropospheric mole fractions of dichloromethane (mean lifetime of 5 months) have increased by a factor of 2 at remote sites throughout the globe. Dichloromethane currently adds more chlorine to the atmosphere (~80 ppt) than either HCFC-141b or HCFC-142b, and the implied resulting increase in stratospheric chlorine in recent years is comparable to the increase in total Cl from HCFCs. Emissions driving this global increase have been estimated at 800 Gg/yr in 2012, which is more than half of the chlorine emitted from the three main CFCs during their peak emissions in the late 1980s. Although dichloromethane is used typically as a cleaning agent, solvent, and feedstock in the production of other chemicals, the cause of the recent atmospheric increase is not well understood. Here we will show that the substantial increase in emissions does not appear to be coming from the U.S., as our ongoing observations from tall towers and aircraft profiles over North America since 2005 show a decreasing trend in measured mole fractions in the continental boundary layer relative to the background atmosphere during this period. Instead, our data from remote sites across the Northern Hemisphere reveal a shift in the atmospheric distribution of dichloromethane since 2000 that implies increased emissions from lower latitudes in the northern hemisphere. These changing distributions will be presented and discussed, along with an exploration of the potential causes for the large inter-annual variations observed in the rate of increase and what the results suggest about the main loss mechanism for dichloromethane: oxidation by the hydroxyl radical.

Operation of the solvent-refined-coal pilot plant, Wilsonville, Alabama. Annual technical report, January-December 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, H.E.

1981-08-01

The plant was in operation for the equivalent of 247 days, an on-stream factor of 67.7%. Kentucky 9 coals from the Lafayette, Dotiki and Fies mines were processed. During 1980, the operating conditions and equipment were adjusted to evaluate potential process improvements. These experiments produced significant results in the following areas: Operating V103 High Pressure Separator in the hot mode; varying T102 Vacuum Column operating temperature; adding light SRC (LSRC), a product of the third stage of the Critical Solvent Deashing (CSD) unit, to the process solvent; investigating the effects of the chlorine content of the feed coal on corrosionmore » in the process vessels; evaluating the effects of adding sodium carbonate on corrosion rates; operating under conditions of low severity; i.e., low reactor temperature and long residence time; and testing an alternate CSD deashing solvent. A series of simulation runs investigating the design operating conditions for a planned 6000 ton per day SRC-I demonstation plant were also completed. Numerous improvements were made in the CSD processing area, and the components for a hydrotreating unit were installed.« less

Multi-element compound specific stable isotope analysis of chlorinated aliphatic contaminants derived from chlorinated pitches.

PubMed

Filippini, Maria; Nijenhuis, Ivonne; Kümmel, Steffen; Chiarini, Veronica; Crosta, Giovanni; Richnow, Hans H; Gargini, Alessandro

2018-05-30

Tetrachloroethene and trichloroethene are typical by-products of the industrial production of chloromethanes. These by-products are known as "chlorinated pitches" and were often dumped in un-contained waste disposal sites causing groundwater contaminations. Previous research showed that a strongly depleted stable carbon isotope signature characterizes chlorinated compounds associated with chlorinated pitches whereas manufactured commercial compounds have more enriched carbon isotope ratios. The findings were restricted to a single case study and one element (i.e. carbon). This paper presents a multi-element Compound-Specific Stable Isotope Analysis (CSIA, including carbon, chlorine and hydrogen) of chlorinated aliphatic contaminants originated from chlorinated pitches at two sites with different hydrogeology and different producers of chloromethanes. The results show strongly depleted carbon signatures at both sites whereas the chlorine and the hydrogen signatures are comparable to those presented in the literature for manufactured commercial compounds. Multi-element CSIA allowed the identification of sources and site-specific processes affecting chloroethene transformation in groundwater as a result of emergency remediation measures. CSIA turned out to be an effective forensic tool to address the liability for the contamination, leading to a conviction for the crimes of unintentional aggravated public water supply poisoning and environmental disaster. Copyright © 2018 Elsevier B.V. All rights reserved.

40 CFR 63.1215 - What are the health-based compliance alternatives for total chlorine?

Code of Federal Regulations, 2012 CFR

2012-07-01

... SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants from Hazardous Waste... chlorine under the procedures prescribed in this section for your hazardous waste combustors other than... concentration (ppmv) expressed as chloride (Cl(−)) equivalent for each on site hazardous waste combustor. You...

Effects of Solvent and Ion Source Pressure on the Analysis of Anabolic Steroids by Low Pressure Photoionization Mass Spectrometry.

PubMed

Liu, Chengyuan; Zhu, Yanan; Yang, Jiuzhong; Zhao, Wan; Lu, Deen; Pan, Yang

2017-04-01

Solvent and ion source pressure were two important factors relating to the photon induced ion-molecule reactions in low pressure photoionization (LPPI). In this work, four anabolic steroids were analyzed by LPPI mass spectrometry. Both the ion species present and their relative abundances could be controlled by switching the solvent and adjusting the ion source pressure. Whereas M •+ , MH + , [M - H 2 O] + , and solvent adducts were observed in positive LPPI, [M - H] - and various oxidation products were abundant in negative LPPI. Changing the solvent greatly affected formation of the ion species in both positive and negative ion modes. The ion intensities of the solvent adduct and oxygen adduct were selectively enhanced when the ion source pressure was elevated from 68 to 800 Pa. The limit of detection could be decreased by increasing the ion source pressure. Graphical Abstract ᅟ.

Effects of Solvent and Ion Source Pressure on the Analysis of Anabolic Steroids by Low Pressure Photoionization Mass Spectrometry

NASA Astrophysics Data System (ADS)

Liu, Chengyuan; Zhu, Yanan; Yang, Jiuzhong; Zhao, Wan; Lu, Deen; Pan, Yang

2017-04-01

Solvent and ion source pressure were two important factors relating to the photon induced ion-molecule reactions in low pressure photoionization (LPPI). In this work, four anabolic steroids were analyzed by LPPI mass spectrometry. Both the ion species present and their relative abundances could be controlled by switching the solvent and adjusting the ion source pressure. Whereas M•+, MH+, [M - H2O]+, and solvent adducts were observed in positive LPPI, [M - H]- and various oxidation products were abundant in negative LPPI. Changing the solvent greatly affected formation of the ion species in both positive and negative ion modes. The ion intensities of the solvent adduct and oxygen adduct were selectively enhanced when the ion source pressure was elevated from 68 to 800 Pa. The limit of detection could be decreased by increasing the ion source pressure.

Viral Pollution of Surface Waters Due to Chlorinated Primary Effluents

PubMed Central

Sattar, Syed A.; Westwood, J. C. N.

1978-01-01

The role of chlorinated primary effluents in viral pollution of the Ottawa River (Ontario) was assessed by examining 282 field samples of wastewaters from two different sewage treatment plants over a 2-year period. The talc-Celite technique was used for sample concentration, and BS-C-1 cells were employed for virus detection. Viruses were detected in 80% (75/94) of raw sewage, 72% (68/94) of primary effluent, and 56% (53/94) of chlorinated effluent samples. Both raw sewage and primary effluent samples contained about 100 viral infective units (VIU) per 100 ml. Chlorination produced a 10- to 50-fold reduction in VIU and gave nearly 2.7 VIU/100 ml of chlorinated primary effluent. With a combined daily chlorinated primary effluent output of approximately 3.7 × 108 liters, these two plants were discharging 1.0 × 1010 VIU per day. Because the river has a mean annual flow of 8.0 × 1010 liters per day, these two sources alone produced a virus loading of 1.0 VIU/8 liters of the river water. This river also receives at least 9.0 × 107 liters of raw sewage per day and undetermined but substantial amounts of storm waters and agricultural wastes. It is used for recreation and acts as a source of potable water for some 6.0 × 105 people. In view of the potential of water for disease transmission, discharge of such wastes into the water environment needs to be minimized. PMID:215085

Effect of heterogeneity on enhanced reductive dechlorination: Analysis of remediation efficiency and groundwater acidification

NASA Astrophysics Data System (ADS)

Brovelli, A.; Lacroix, E.; Robinson, C. E.; Gerhard, J.; Holliger, C.; Barry, D. A.

2011-12-01

Enhanced reductive dehalogenation is an attractive in situ treatment technology for chlorinated contaminants. The process includes two acid-forming microbial reactions: fermentation of an organic substrate resulting in short-chain fatty acids, and dehalogenation resulting in hydrochloric acid. The accumulation of acids and the resulting drop of groundwater pH are controlled by the mass and distribution of chlorinated solvents in the source zone, type of electron donor, alternative terminal electron acceptors available and presence of soil mineral phases able to buffer the pH (such as carbonates). Groundwater acidification may reduce or halt microbial activity, and thus dehalogenation, significantly increasing the time and costs required to remediate the aquifer. In previous work a detailed geochemical and groundwater flow simulator able to model the fermentation-dechlorination reactions and associated pH change was developed. The model accounts for the main processes influencing microbial activity and groundwater pH, including the groundwater composition, the electron donor used and soil mineral phase interactions. In this study, the model was applied to investigate how spatial variability occurring at the field scale affects dechlorination rates, groundwater pH and ultimately the remediation efficiency. Numerical simulations were conducted to examine the influence of heterogeneous hydraulic conductivity on the distribution of the injected, fermentable substrate and on the accumulation/dilution of the acidic products of reductive dehalogenation. The influence of the geometry of the DNAPL source zone was studied, as well as the spatial distribution of soil minerals. The results of this study showed that the heterogeneous distribution of the soil properties have a potentially large effect on the remediation efficiency. For examples, zones of high hydraulic conductivity can prevent the accumulation of acids and alleviate the problem of groundwater acidification. The conclusions drawn and insights gained from this modeling study will be useful to design improved in-situ enhanced dehalogenation remediation schemes.

Tracing chlorine sources of thermal and mineral springs along and across the Cascade Range using halogen and chlorine isotope compositions

USGS Publications Warehouse

Cullen, Jeffrey T.; Barnes, Jaime D.; Hurwitz, Shaul; Leeman, William P.

2015-01-01

In order to provide constraints on the sources of chlorine in spring waters associated with arc volcanism, the major/minor element concentrations and stable isotope compositions of chlorine, oxygen, and hydrogen were measured in 28 thermal and mineral springs along the Cascade Range in northwestern USA. Chloride concentrations in the springs range from 64 to 19,000 mg/L and View the MathML source values range from +0.2‰ to +1.9‰ (average=+1.0±0.4‰), with no systematic variation along or across the arc, nor correlations with their presumed underlying basement lithologies. Additionally, nine geochemically well-characterized lavas from across the Mt. St. Helens/Mt. Adams region of the Cascade Range (Leeman et al., 2004 and Leeman et al., 2005) were analyzed for their halogen concentrations and Cl isotope compositions. In the arc lavas, Cl and Br concentrations from the volcanic front are higher than in lavas from the forearc and backarc. F and I concentrations progressively decrease from forearc to backarc, similar to the trend documented for B in most arcs. View the MathML source values of the lavas range from −0.1 to +0.8‰ (average = +0.4±0.3‰). Our results suggest that the predominantly positive View the MathML source values observed in the springs are consistent with water interaction with underlying 37Cl-enriched basalt and/or altered oceanic crust, thereby making thermal spring waters a reasonable proxy for the Cl isotope compositions of associated volcanic rocks in the Cascades. However, waters with View the MathML source values >+1.0‰ also suggest additional contributions of chlorine degassed from cooling magmas due to subsurface vapor–liquid HCl fractionation in which Cl is lost to the aqueous fluid phase and 37Cl is concentrated in the ascending magmatic HCl vapor. Future work is necessary to better constrain Cl isotope behavior during volcanic degassing and fluid–rock interaction in order to improve volatile flux estimates through subduction zones.

Addition of chlorine during water purification reduces iodine content of drinking water and contributes to iodine deficiency.

PubMed

Samson, L; Czegeny, I; Mezosi, E; Erdei, A; Bodor, M; Cseke, B; Burman, K D; Nagy, E V

2012-01-01

Drinking water is the major natural source of iodine in many European countries. In the present study, we examined possible sites of iodine loss during the usual water purification process.Water samples from 6 sites during the technological process were taken and analyzed for iodine content. Under laboratory circumstances, prepared iodine in water solution has been used as a model to test the effect of the presence of chlorine. Samples from the purification sites revealed that in the presence of chlorine there is a progressive loss of iodine from the water. In the chlorine concentrations employed in the purification process, 24-h chlorine exposure eliminated more than 50% of iodine when the initial iodine concentration was 250 μg/l or less. Iodine was completely eliminated if the starting concentration was 16 μg/l.We conclude that chlorine used during water purification may be a major contributor to iodine deficiency in European communities.

Environmental analysis of the life cycle emissions of 2-methyl tetrahydrofuran solvent manufactured from renewable resources.

PubMed

Slater, C Stewart; Savelski, Mariano J; Hitchcock, David; Cavanagh, Eduardo J

2016-01-01

An environmental analysis has been conducted to determine the cradle to gate life cycle emissions to manufacture the green solvent, 2-methyl tetrahydrofuran. The solvent is considered a greener chemical since it can be manufactured from renewable resources with a lower life cycle footprint. Analyses have been performed using different methods to show greenness in both its production and industrial use. This solvent can potentially be substituted for other ether and chlorinated solvents commonly used in organometallic and biphasic reactions steps in pharmaceutical and fine chemical syntheses. The 2-methyl tetrahydrofuran made from renewable agricultural by-products is marketed by Penn A Kem under the name ecoMeTHF™. The starting material, 2-furfuraldehyde (furfural), is produced from corn cob waste by converting the available pentosans by acid hydrolysis. An evaluation of each step in the process was necessary to determine the overall life cycle and specific CO2 emissions for each raw material/intermediate produced. Allocation of credits for CO2 from the incineration of solvents made from renewable feedstocks significantly reduced the overall carbon footprint. Using this approach, the overall life cycle emissions for production of 1 kg of ecoMeTHF™ were determined to be 0.191 kg, including 0.150 kg of CO2. Life cycle emissions generated from raw material manufacture represents the majority of the overall environmental impact. Our evaluation shows that using 2-methyl tetrahydrofuran in an industrial scenario results in a 97% reduction in emissions, when compared to typically used solvents such as tetrahydrofuran, made through a conventional chemical route.

Design Guidance for Application of Permeable Barriers to Remediate Dissolved Chlorinated Solvents,

DTIC Science & Technology

1997-02-01

fill slurry composed of a reactive medium, such as iron powder and guar gum , can then be injected into the fracture to form a reactive treatment zone...slurry (Owaidat, 1996). The slurry, which is composed of powdered guar bean, acts to maintain the integrity of the trench walls during installation of...the cell. The guar gum will later biodegrade to mostly water after wall completion, and will have minimal effect on the permeability of the trench

Development of Effective Aerobic Cometabolic Systems for the In Situ Transformation of Problematic Chlorinated Solvent Mixtures

DTIC Science & Technology

2005-02-01

vector contained the ampicillin resistance gene , only transformed colonies should grow on the plates and since the inserted DNA should have knocked...flava 340 209 203 69 2422 Nitrogen-fixing bacterium MI753 340 209 203 69 2571 Pseudomonas spinosa 340 209 203 217 2458 Xylophilus ampelinus 340 209...277 203 198 2767 Unidentified bacterium 340 277 203 198 2674 Type 0803 filamentous bacterium 340 277 203 198 2581 Xylophilus ampelinus 340 209 203 217

Quantitative Framework and Management Expectation Tool for the Selection of Bioremediation Approaches at Chlorinated Solvent Sites

DTIC Science & Technology

2015-03-19

to Abiotic Degradation  Magnetite (FeO.Fe2O3) often occurs naturally in sediments formed by weathering of igneous or metamorphic rock  Magnetite...send questions at any time using the Q&A panel 6 SERDP & ESTCP Webinar Series (#11) SERDP & ESTCP Webinar Series SERDP and ESTCP Overview Andrea...Attenuation (MNA)  Integrate the decision-making framework into an easy to use application • Excel spreadsheet  Guide users in the selection of

Phytoremediation and innovative strategies for specialized remedial actions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alleman, B.C.; Leeson, A.

1999-01-01

Phytoremediation is a site remediation strategy whose time seems to have come in the past few years, with field implementations taking place in a host of applications. From laboratory studies on plant uptake to full-scale phytoremediation treatment strategies, this volume covers the use of plants to treat contaminants such as hydrocarbons, metals, pesticides, perchlorate, and chlorinated solvents. In addition to the phytoremediation studies, this volume also covers specialized remediation approaches such as sequential anaerobic/aerobic in situ treatment, membrane bioreactors, and Fenton's reagent oxidation.

Phytoremediation and innovative strategies for specialized remedial actions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alleman, B.C.; Leeson, A.

1999-11-01

Phytoremediation is a site remediation strategy whose time seems to have come in the past few years, with field implementations taking place in a host of applications. From laboratory studies on plant uptake to full-scale phytoremediation treatment strategies, this volume covers the use of plants to treat contaminants such as hydrocarbons, metals, pesticides, perchlorate, and chlorinated solvents. In addition to the phytoremediation studies, this volume also covers specialized remediation approaches such as sequential anaerobic/aerobic in situ treatment, membrane bioreactors, and Fenton`s reagent oxidation.

Phytoremediation and innovative strategies for specialized remedial applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alleman, B.C.; Leeson, A.

1999-10-01

Phytoremediation is a site remediation strategy whose time seems to have come in the past few years, with field implementations taking place in a host of applications. From laboratory studies on plant uptake to full-scale phytoremediation treatment strategies, this volume covers the use of plants to treat contaminants such as hydrocarbons, metals, pesticides, perchlorate, and chlorinated solvents. In addition to the phytoremediation studies, this volume also covers specialized remediation approaches such as sequential anaerobic/aerobic in situ treatment, membrane bioreactors, and Fenton`s reagent oxidation.

Impact of Clay DNAPL Interactions on Transport and Storage of Chlorinated Solvents in Low Permeability Zones

DTIC Science & Technology

2015-02-01

producing cracking, in a time frame on the order of weeks. The hypothesized mechanism is syneresis, involving the sorption of the surfactants from...49 4.0 Determination of Mechanism of Clay Structure Modification 53 ii 4.1 Introduction 53 4.2 Materials and Methods 52 4.2.1. Screening...Spectroscopy (FTIR) Measurements 65 4.3.4. Sorption Experiments 68 4.4 Proposed Mechanism for Basal Spacing Decrease 70 4.5 Conclusions 72 5.0

Frequently Asked Questions about Monitored Natural Attenuation in Groundwater

DTIC Science & Technology

2014-02-01

Natural Attenuation of Fuels and Chlorinated Solvents book (600 citations) I? • MNA Since 2000 Although there was tremendous progress in technical and...faster with Scenario Scenario Scenario heterogen. 7 8 8 slower with Scenario Scenario Scenario heterogen. 10 I I 12 fractured / • Scenario 13...DC. 7 (W OHC-17 ( 1 E5 yr) ~ 1,2DCA VC Ethylene Glycol (W I RD-7 AH-17 (72 yr) • Mechanisms ORP CEC Sediment iron oxide Sulfur TDS CA

Diagnostic Tools for Performance Evaluation of Innovative In-Situ Remediation Technologies at Chlorinated Solvent-Contaminated Sites

DTIC Science & Technology

2011-07-01

Florida: Dr. Michael Annable, Dr. Kirk Hatfield • Air Force Institute of Technology: Dr. Mark Goltz , Dr. Junqi Huang • United States (U.S.) Environmental...somewhat less than (e.g., 70% of) the natural groundwater flow through the transect (Yoon, 2006; Goltz et al., 2007b). Once the calculated mass...approach ( Goltz et al., 2007a; Wheeldon, 2008) is then used to estimate the mass discharge through the transect. Each RFM application typically

Using Advanced Analysis Approaches to Complete Long-Term Evaluations of Natural Attenuation Processes on the Remediation of Dissolved Chlorinated Solvent Contamination

DTIC Science & Technology

2008-10-01

and UTCHEM (Clement et al., 1998). While all four of these software packages use conservation of mass as the basic principle for tracking NAPL...simulate dissolution of a single NAPL component. UTCHEM can be used to simulate dissolution of a multiple NAPL components using either linear or first...parameters. No UTCHEM a/ 3D model, general purpose NAPL simulator. Yes Virulo a/ Probabilistic model for predicting leaching of viruses in unsaturated

Cleanliness verification process at Martin Marietta Astronautics

NASA Astrophysics Data System (ADS)

King, Elizabeth A.; Giordano, Thomas J.

1994-06-01

The Montreal Protocol and the 1990 Clean Air Act Amendments mandate CFC-113, other chlorinated fluorocarbons (CFC's) and 1,1,1-Trichloroethane (TCA) be banned from production after December 31, 1995. In response to increasing pressures, the Air Force has formulated policy that prohibits purchase of these solvents for Air Force use after April 1, 1994. In response to the Air Force policy, Martin Marietta Astronautics is in the process of eliminating all CFC's and TCA from use at the Engineering Propulsion Laboratory (EPL), located on Air Force property PJKS. Gross and precision cleaning operations are currently performed on spacecraft components at EPL. The final step of the operation is a rinse with a solvent, typically CFC-113. This solvent is then analyzed for nonvolatile residue (NVR), particle count and total filterable solids (TFS) to determine cleanliness of the parts. The CFC-113 used in this process must be replaced in response to the above policies. Martin Marietta Astronautics, under contract to the Air Force, is currently evaluating and testing alternatives for a cleanliness verification solvent. Completion of test is scheduled for May, 1994. Evaluation of the alternative solvents follows a three step approach. This first is initial testing of solvents picked from literature searches and analysis. The second step is detailed testing of the top candidates from the initial test phase. The final step is implementation and validation of the chosen alternative(s). Testing will include contaminant removal, nonvolatile residue, material compatibility and propellant compatibility. Typical materials and contaminants will be tested with a wide range of solvents. Final results of the three steps will be presented as well as the implementation plan for solvent replacement.

Direct electrochemical oxidation of ammonia on graphite as a treatment option for stored source-separated urine.

PubMed

Zöllig, Hanspeter; Fritzsche, Cristina; Morgenroth, Eberhard; Udert, Kai M

2015-02-01

Electrolysis can be a viable technology for ammonia removal from source-separated urine. Compared to biological nitrogen removal, electrolysis is more robust and is highly amenable to automation, which makes it especially attractive for on-site reactors. In electrolytic wastewater treatment, ammonia is usually removed by indirect oxidation through active chlorine which is produced in-situ at elevated anode potentials. However, the evolution of chlorine can lead to the formation of chlorate, perchlorate, chlorinated organic by-products and chloramines that are toxic. This study focuses on using direct ammonia oxidation on graphite at low anode potentials in order to overcome the formation of toxic by-products. With the aid of cyclic voltammetry, we demonstrated that graphite is active for direct ammonia oxidation without concomitant chlorine formation if the anode potential is between 1.1 and 1.6 V vs. SHE (standard hydrogen electrode). A comparison of potentiostatic bulk electrolysis experiments in synthetic stored urine with and without chloride confirmed that ammonia was removed exclusively by continuous direct oxidation. Direct oxidation required high pH values (pH > 9) because free ammonia was the actual reactant. In real stored urine (pH = 9.0), an ammonia removal rate of 2.9 ± 0.3 gN·m(-2)·d(-1) was achieved and the specific energy demand was 42 Wh·gN(-1) at an anode potential of 1.31 V vs. SHE. The measurements of chlorate and perchlorate as well as selected chlorinated organic by-products confirmed that no chlorinated by-products were formed in real urine. Electrode corrosion through graphite exfoliation was prevented and the surface was not poisoned by intermediate oxidation products. We conclude that direct ammonia oxidation on graphite electrodes is a treatment option for source-separated urine with three major advantages: The formation of chlorinated by-products is prevented, less energy is consumed than in indirect ammonia oxidation and readily available and cheap graphite can be used as the electrode material. Copyright © 2014 Elsevier Ltd. All rights reserved.

RAILCAR4 Toxic Industrial Chemical Source Characterization Program (Software User’s Manual)

DTIC Science & Technology

2011-08-01

hydroxide (29%) boron trifluoride sulfur trioxide hydrogen chloride methyl bromide phosphine hydrochloric acid (39%) phosphoryl trichloride arsine...Data for Chlorine Trial 05-RC ...............................20 10 Nitric Acid Thermodynamic Properties...Table 1. TICs Available for RAILCAR Simulations chlorine hydrobromic acid (48%) acetylene tetrabromide ammonia OMPA o-anisidine ammonium

Predicting total organic carbon load with El Nino southern oscillation phase using hybrid and fuzzy logic approaches

USDA-ARS?s Scientific Manuscript database

During drinking water treatment chlorine reacts with total organic carbon (TOC) to form disinfection byproducts (DBP), some of which can be carcinogenic. Additional treatment required to remove TOC before chlorination significantly increases treatment cost. There are two main sources of TOC in a wat...

Toxicity comparison of chlorinated and brominated dibenzo-p-dioxins and dibenzofurans in industrial source samples by HRGC/HRMS and enzyme immunoassay

EPA Science Inventory

Limited information is available on the applicability of polychlorinated dibenzo-p-dioxin/furan (PCDD/F) toxicity assays to their brominated counterparts: polybrominated dibenzo-p-dixoins/furans (PBDDs/Fs). We estimated the toxicity of mixtures of chlorinated, brominated, and mi...

Determination of Chlorine in Milk via Molecular Absorption of SrCl Using High-Resolution Continuum Source Graphite Furnace Atomic Absorption Spectrometry.

PubMed

Ozbek, Nil; Akman, Suleyman

2016-07-20

Total chlorine in milk was determined via the molecular absorption of diatomic strontium monochloride at 635.862 nm using high-resolution continuum source graphite furnace atomic absorption spectrometry. The effects of coating the graphite furnace, using different modifiers, amount of molecule-forming element, and different calibrants were investigated and optimized. Chlorine concentrations in milk samples were determined in a Zr-coated graphite furnace using 25 μg of Sr as the molecule-forming reagent and applying a pyrolysis temperature of 600 °C and a molecule-forming temperature of 2300 °C. Linearity was maintained up to 500 μg mL(-1) of Cl. The method was tested by analyzing a certified reference wastewater. The results were in the uncertainty limits of the certified value. The limit of detection of the method was 1.76 μg mL(-1). The chlorine concentrations in various cow milk samples taken from the market were found in the range of 588-1472 mg L(-1).

Evaluation of geophysical logs and video surveys in boreholes adjacent to the Berkley Products Superfund Site, West Cocalico Township, Lancaster County, Pennsylvania

USGS Publications Warehouse

Low, Dennis J.; Conger, Randall W.

1998-01-01

Between February 1998 and April 1998, geophysical logs were collected in nine boreholes adjacent to the Berkley Products Superfund Site, West Cocalico Township, Lancaster County, Pa. Video surveys were conducted on four of the nine boreholes. The boreholes range in depth from 320 to 508 feet below land surface, are completed open holes, have ambient vertical flow of water, and penetrate a series of interbedded siltstone, sandstone, and conglomerate units. The purpose of collecting geophysical-log data was to help determine horizontal and vertical distribution of contaminated ground water migrating from known or suspected sources and to aid in the placement of permanent borehole packers. The primary contaminants were derived from paint waste that included pigment sludges and wash solvents. The chlorinated volatile organic compounds probably originated from the wash solvents.Caliper logs and video surveys were used to locate fractures; inflections on fluid-resistivity and fluid-temperature logs were used to locate possible water-bearing fractures. Heatpulse-flowmeter measurements were used to verify the locations of water-producing or water-receiving zones and to measure rates of flow between water-bearing fractures. Single-point-resistance and natural-gamma logs provided information on stratigraphy. After interpretation of geophysical logs, video surveys, and driller's logs, permanent multiple-packer systems were installed in each borehole to obtain depth specific water samples from one or more water-bearing fractures in each borehole.

Identifying the underlying causes of biological instability in a full-scale drinking water supply system.

PubMed

Nescerecka, Alina; Juhna, Talis; Hammes, Frederik

2018-05-15

Changes in bacterial concentration and composition in drinking water during distribution are often attributed to biological (in)stability. Here we assessed temporal biological stability in a full-scale distribution network (DN) supplied with different types of source water: treated and chlorinated surface water and chlorinated groundwater produced at three water treatment plants (WTP). Monitoring was performed weekly during 12 months in two locations in the DN. Flow cytometric total and intact cell concentration (ICC) measurements showed considerable seasonal fluctuations, which were different for two locations. ICC varied between 0.1-3.75 × 10 5  cells mL -1 and 0.69-4.37 × 10 5  cells mL -1 at two locations respectively, with ICC increases attributed to temperature-dependent bacterial growth during distribution. Chlorinated water from the different WTP was further analysed with a modified growth potential method, identifying primary and secondary growth limiting compounds. It was observed that bacterial growth in the surface water sample after chlorination was primarily inhibited by phosphorus limitation and secondly by organic carbon limitation, while carbon was limiting in the chlorinated groundwater samples. However, the ratio of available nutrients changed during distribution, and together with disinfection residual decay, this resulted in higher bacterial growth potential detected in the DN than at the WTP. In this study, bacterial growth was found to be higher (i) at higher water temperatures, (ii) in samples with lower chlorine residuals and (iii) in samples with less nutrient (carbon, phosphorus, nitrogen, iron) limitation, while this was significantly different between the samples of different origin. Thus drinking water microbiological quality and biological stability could change during different seasons, and the extent of these changes depends on water temperature, the water source and treatment. Furthermore, differences in primary growth limiting nutrients in different water sources could contribute to biological instability in the network, where mixing occurs. Copyright © 2018 Elsevier Ltd. All rights reserved.

Inactivation of Renibacterium salmoninarum by free chlorine

USGS Publications Warehouse

Pascho, Ronald J.; Landolt, Marsha L.; Ongerth, Jerry E.

1995-01-01

Salmonid fishes contract bacterial kidney disease by vertical or horizontal transmission of the pathogenic bacterium, Renibacterium salmoninarum. Procedures to reduce vertical transmission are under evaluation, but methods are still needed to eliminate sources of waterborne R. salmoninarum. We examined the efficacy of chlorine to inactivate R. salmoninarum. The bacterium was exposed to various levels of chlorine at pH 6, 7, or 8, and at 7.5 °C or 15 °C. At pH 7 and 15 °C, 99% inactivation occurred within 18 s, even at free chlorine concentrations as low as 0.05 mg/l. Chlorine was most effective at neutral or acidic pH, and 15 °C. The inactivation curves for 7.5 °C and pH 7, or 15 °C and pH 8, deviated from first-order kinetics by exhibiting shoulders or a tailing-off effect, suggesting that chlorine and the bacterial cells were not the sole reactants. A plot of the concentration-time (Ct) products for free chlorine at pH 7 and 15 °C produced a line with a slope less than 1, indicating that the duration of exposure was more important than the concentration of free chlorine. These data indicate that R. salmoninarum is very sensitive to chlorine, and that this disinfectant may be appropriate for use in fish hatcheries rearing salmonids affected by bacterial kidney disease.

Organochlorine compounds and the biogeochemical cycle of chlorine in soils: A review

NASA Astrophysics Data System (ADS)

Vodyanitskii, Yu. N.; Makarov, M. I.

2017-09-01

Chloride ions in soil may interact with soil organic matter and form organochlorine compounds in situ. The biotic chlorination of soil organic substances takes places under aerobic conditions with participation of H2O2 forming from peroxidases released by soil microorganisms (in particular, by microscopic fungi). The abiotic chlorination results also from the redox reactions with the participation of Fe3+/Fe2+ system, but it develops several times slower. Chlorination of soil organic substances is favored by Cl- coming to soil both from natural (salinized soil-forming rocks and groundwater, sea salt) and anthropogenic sources of chlorides, i.e., spills of saline water at oil production, road deicing chemicals, mineral fertilizers, etc. The study of the biogeochemical chlorine cycle should take into account the presence of organochlorine compounds in soils, in addition to transformation and migration of chloride ions.

Impact of wastewater infrastructure upgrades on the urban water cycle: Reduction in halogenated reaction byproducts following conversion from chlorine gas to ultraviolet light disinfection

USGS Publications Warehouse

Barber, Larry B.; Hladik, Michelle; Vajda, Alan M.; Fitzgerald, Kevin C.; Douville, Chris

2015-01-01

The municipal wastewater treatment facility (WWTF) infrastructure of the United States is being upgraded to expand capacity and improve treatment, which provides opportunities to assess the impact of full-scale operational changes on water quality. Many WWTFs disinfect their effluent prior to discharge using chlorine gas, which reacts with natural and synthetic organic matter to form halogenated disinfection byproducts (HDBPs). Because HDBPs are ubiquitous in chlorine-disinfected drinking water and have adverse human health implications, their concentrations are regulated in potable water supplies. Less is known about the formation and occurrence of HDBPs in disinfected WWTF effluents that are discharged to surface waters and become part of the de facto wastewater reuse cycle. This study investigated HDBPs in the urban water cycle from the stream source of the chlorinated municipal tap water that comprises the WWTF inflow, to the final WWTF effluent disinfection process before discharge back to the stream. The impact of conversion from chlorine-gas to low-pressure ultraviolet light (UV) disinfection at a full-scale (68,000 m3 d−1 design flow) WWTF on HDBP concentrations in the final effluent was assessed, as was transport and attenuation in the receiving stream. Nutrients and trace elements (boron, copper, and uranium) were used to characterize the different urban source waters, and indicated that the pre-upgrade and post-upgrade water chemistry was similar and insensitive to the disinfection process. Chlorinated tap water during the pre-upgrade and post-upgrade samplings contained 11 (mean total concentration = 2.7 μg L−1; n=5) and 10 HDBPs (mean total concentration = 4.5 μg L−1), respectively. Under chlorine-gas disinfection conditions 13 HDBPs (mean total concentration = 1.4 μg L−1) were detected in the WWTF effluent, whereas under UV disinfection conditions, only one HDBP was detected. The chlorinated WWTF effluent had greater relative proportions of nitrogenous, brominated, and iodinated HDBPs than the chlorinated tap water. Conversion of the WWTF to UV disinfection reduced the loading of HDBPs to the receiving stream by >90%.

Impact of wastewater infrastructure upgrades on the urban water cycle: Reduction in halogenated reaction byproducts following conversion from chlorine gas to ultraviolet light disinfection.

PubMed

Barber, Larry B; Hladik, Michelle L; Vajda, Alan M; Fitzgerald, Kevin C; Douville, Chris

2015-10-01

The municipal wastewater treatment facility (WWTF) infrastructure of the United States is being upgraded to expand capacity and improve treatment, which provides opportunities to assess the impact of full-scale operational changes on water quality. Many WWTFs disinfect their effluent prior to discharge using chlorine gas, which reacts with natural and synthetic organic matter to form halogenated disinfection byproducts (HDBPs). Because HDBPs are ubiquitous in chlorine-disinfected drinking water and have adverse human health implications, their concentrations are regulated in potable water supplies. Less is known about the formation and occurrence of HDBPs in disinfected WWTF effluents that are discharged to surface waters and become part of the de facto wastewater reuse cycle. This study investigated HDBPs in the urban water cycle from the stream source of the chlorinated municipal tap water that comprises the WWTF inflow, to the final WWTF effluent disinfection process before discharge back to the stream. The impact of conversion from chlorine-gas to low-pressure ultraviolet light (UV) disinfection at a full-scale (68,000 m(3) d(-1) design flow) WWTF on HDBP concentrations in the final effluent was assessed, as was transport and attenuation in the receiving stream. Nutrients and trace elements (boron, copper, and uranium) were used to characterize the different urban source waters, and indicated that the pre-upgrade and post-upgrade water chemistry was similar and insensitive to the disinfection process. Chlorinated tap water during the pre-upgrade and post-upgrade samplings contained 11 (mean total concentration=2.7 μg L(-1); n=5) and 10 HDBPs (mean total concentration=4.5 μg L(-1)), respectively. Under chlorine-gas disinfection conditions 13 HDBPs (mean total concentration=1.4 μg L(-1)) were detected in the WWTF effluent, whereas under UV disinfection conditions, only one HDBP was detected. The chlorinated WWTF effluent had greater relative proportions of nitrogenous, brominated, and iodinated HDBPs than the chlorinated tap water. Conversion of the WWTF to UV disinfection reduced the loading of HDBPs to the receiving stream by >90%. Copyright © 2015. Published by Elsevier B.V.

Chemical reactivity indices for the complete series of chlorinated benzenes: solvent effect.

PubMed

Padmanabhan, J; Parthasarathi, R; Subramanian, V; Chattaraj, P K

2006-03-02

We present a comprehensive analysis to probe the effect of solvation on the reactivity of the complete series of chlorobenzenes through the conceptual density functional theory (DFT)-based global and local descriptors. We propose a multiphilic descriptor in this study to explore the nature of attack at a particular site in a molecule. It is defined as the difference between nucleophilic and electrophilic condensed philicity functions. This descriptor is capable of explaining both the nucleophilicity and electrophilicity of the given atomic sites in the molecule simultaneously. The predictive ability of this descriptor is tested on the complete series of chlorobenzenes in gas and solvent media. A structure-toxicity analysis of these entire sets of chlorobenzenes toward aquatic organisms demonstrates the importance of the electrophilicity index in the prediction of the reactivity/toxicity.

Reversed phase liquid chromatography with UV absorbance and flame ionization detection using a water mobile phase and a cyano propyl stationary phase Analysis of alcohols and chlorinated hydrocarbons.

PubMed

Quigley, W W; Ecker, S T; Vahey, P G; Synovec, R E

1999-10-01

The development of liquid chromatography with a commercially available cyano propyl stationary phase and a 100% water mobile phase is reported. Separations were performed at ambient temperature, simplifying instrumental requirements. Excellent separation efficiency using a water mobile phase was achieved, for example N=18 800, or 75 200 m(-1), was obtained for resorcinol, at a retention factor of k'=4.88 (retention time of 9.55 min at 1 ml min(-1) for a 25 cmx4.6 mm i.d. column, packed with 5 mum diameter particles with the cyano propyl stationary phase). A separation via reversed phase liquid chromatography (RP-LC) with a 100% water mobile phase of six phenols and related compounds was compared to a separation of the same compounds by traditional RP-LC, using octadecylsilane (ODS), i.e. C18, bound to silica and an aqueous mobile phase modified with acetonitrile. Nearly identical analysis time was achieved for the separation of six phenols and related compounds using the cyano propyl stationary phase with a 100% water mobile phase, as compared to traditional RP-LC requiring a relatively large fraction of organic solvent modifier in the mobile phase (25% acetonitrile:75% water). Additional understanding of the retention mechanism with the 100% water mobile phase was obtained by relating measured retention factors of aliphatic alcohols, phenols and related compounds, and chlorinated hydrocarbons to their octanol:water partition coefficients. The retention mechanism is found to be consistent with a RP-LC mechanism coupled with an additional retention effect due to residual hydroxyl groups on the cyano propyl stationary phase. Advantages due to a 100% water mobile phase for the chemical analysis of alcohol mixtures and chlorinated hydrocarbons are reported. By placing an absorbance detector in-series and preceding a novel drop interface to a flame ionization detector (FID), selective detection of a separated mixture of phenols and related compounds and aliphatic alcohols is achieved. The compound class of aliphatic alcohols is selectively and sensitively detected by the drop interface/FID, and the phenols and related compounds are selectively and sensitively detected by absorbance detection at 200 nm. The separation and detection of chlorinated hydrocarbons in a water sample matrix further illustrated the advantages of this methodology. The sensitivity and selectivity of the FID signal for the chlorinated hydrocarbons are significantly better than absorbance detection, even at 200 nm. This methodology is well suited to continuous and automated monitoring of water samples. The applicability of samples initially in an organic solvent matrix is explored, since an organic sample matrix may effect retention and efficiency. Separations in acetonitrile and isopropyl alcohol sample matrices compared well to separations with a water sample matrix.

Three Dimensional Vapor Intrusion Modeling: Model Validation and Uncertainty Analysis

NASA Astrophysics Data System (ADS)

Akbariyeh, S.; Patterson, B.; Rakoczy, A.; Li, Y.

2013-12-01

Volatile organic chemicals (VOCs), such as chlorinated solvents and petroleum hydrocarbons, are prevalent groundwater contaminants due to their improper disposal and accidental spillage. In addition to contaminating groundwater, VOCs may partition into the overlying vadose zone and enter buildings through gaps and cracks in foundation slabs or basement walls, a process termed vapor intrusion. Vapor intrusion of VOCs has been recognized as a detrimental source for human exposures to potential carcinogenic or toxic compounds. The simulation of vapor intrusion from a subsurface source has been the focus of many studies to better understand the process and guide field investigation. While multiple analytical and numerical models were developed to simulate the vapor intrusion process, detailed validation of these models against well controlled experiments is still lacking, due to the complexity and uncertainties associated with site characterization and soil gas flux and indoor air concentration measurement. In this work, we present an effort to validate a three-dimensional vapor intrusion model based on a well-controlled experimental quantification of the vapor intrusion pathways into a slab-on-ground building under varying environmental conditions. Finally, a probabilistic approach based on Monte Carlo simulations is implemented to determine the probability distribution of indoor air concentration based on the most uncertain input parameters.

Multi-isotope (carbon and chlorine) analysis for fingerprinting and site characterization at a fractured bedrock aquifer contaminated by chlorinated ethenes.

PubMed

Palau, Jordi; Marchesi, Massimo; Chambon, Julie C C; Aravena, Ramon; Canals, Àngels; Binning, Philip J; Bjerg, Poul L; Otero, Neus; Soler, Albert

2014-03-15

The use of compound specific multi-isotope approach (C and Cl) in the characterization of a chlorinated ethenes contaminated fractured aquifer allows the identification of several sources and contaminant plumes, as well as the occurrence of biodegradation and mixing processes. The study site is located in Spain with contamination resulting in groundwater concentrations of up to 50mg/L of trichloroethene (TCE), the most abundant chlorinated ethene, and 7 mg/L of tetrachloroethene (PCE). The potential sources of contamination including abandoned barrels, an underground tank, and a disposal lagoon, showed a wide range in δ(13)C values from -15.6 to -40.5‰ for TCE and from -18.5 to -32.4‰ for PCE, allowing the use of isotope fingerprinting for tracing of the origin and migration of these contaminants in the aquifer. In contrast, there is no difference between the δ(37)Cl values for TCE in the contaminant sources, ranging from +0.53 to +0.66‰. Variations of δ(37)Cl and δ(13)C in the different contaminant plumes were used to investigate the role of biodegradation in groundwater. Moreover, the isotopic data were incorporated into a reactive transport model for determination of whether the isotope pattern observed downstream from the tank's source could be explained by the simultaneous effect of mixing and biodegradation. The results demonstrate that a multi-isotope approach is a valuable tool for characterization of complex sites such as fractured bedrock aquifer contaminated by multiple sources, providing important information which can be used by consultants and site managers to prioritize and design more successful remediation strategies. Copyright © 2013 Elsevier B.V. All rights reserved.