40 CFR 430.46 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2013 CFR

2013-07-01

... pretreatment standards for existing sources (PSES) if it uses chlorophenolic-containing biocides. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides. PSES must be attained on or before July 1, 1984: Subpart D [PSES for...

40 CFR 430.36 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2013 CFR

2013-07-01

... pretreatment standards for existing sources (PSES) if it uses chlorophenolic-containing biocides. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using those biocides. PSES must be attained on or before July 1, 1984: Subpart C [PSES for...

40 CFR 430.66 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2014 CFR

2014-07-01

... standards for existing sources (PSES) if it uses chlorophenolic-containing biocides. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides. PSES must be attained on or before July 1, 1984: Subpart F Pollutant or pollutant property PSES...

40 CFR 430.104 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... chlorophenolic-containing biocides are used must achieve the following effluent limitations representing the... applicable to non-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart J [BAT effluent...

40 CFR 430.94 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... chlorophenolic-containing biocides are used must achieve the following effluent limitations representing the... applicable to non-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart I [Facilities...

40 CFR 430.15 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

..., concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used shall be subject to pentachlorophenol and trichlorophenol limitations. Permittees not using chlorophenolic-containing biocides must...

40 CFR 430.75 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

...-continuous dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration... are only applicable at facilities where chlorophenolic-containing biocides are used. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not...

40 CFR 430.75 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-continuous dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration... are only applicable at facilities where chlorophenolic-containing biocides are used. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not...

40 CFR 430.14 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... chlorophenolic-containing biocides are used must achieve the following effluent limitations representing the.../kkg (lb/1000 lb) but shall be subject to concentration limitations. Concentration limitations are only applicable to non-continuous dischargers. Permittees not using chlorophenolic-containing biocides must...

40 CFR 430.106 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2013 CFR

2013-07-01

... biocides. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides. PSES must be attained on or before July 1, 1984: Subpart J...

40 CFR 430.115 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

...-containing biocides are used shall be subject to pentachlorophenol and trichlorophenol limitations. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart K [NSPS for non-integrated mills where fine paper is...

40 CFR 430.34 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... biocides are used must achieve the following effluent limitations representing the degree of effluent...-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart C [BAT effluent limitations for...

40 CFR 430.64 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... biocides are used must achieve the following effluent limitations representing the degree of effluent...-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart F Pollutant or pollutant property BAT...

40 CFR 430.14 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... biocides are used must achieve the following effluent limitations representing the degree of effluent...-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart A [BAT effluent limitations] Pollutant...

40 CFR 430.44 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... biocides are used must achieve the following effluent limitations representing the degree of effluent...-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart D [BAT effluent limitations for...

40 CFR 430.95 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-continuous dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration... biocides are used shall be subject to pentachlorophenol and trichlorophenol limitations. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not...

40 CFR 430.105 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

...-continuous dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration... biocides are used shall be subject to pentachlorophenol and trichlorophenol limitations. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not...

40 CFR 430.95 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

...-continuous dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration... biocides are used shall be subject to pentachlorophenol and trichlorophenol limitations. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not...

40 CFR 430.105 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-continuous dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration... biocides are used shall be subject to pentachlorophenol and trichlorophenol limitations. Permittees not using chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not...

40 CFR 430.34 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... biocides are used must achieve the following effluent limitations representing the degree of effluent... shall be subject to concentration limitations. Concentration limitations are only applicable to non-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit...

40 CFR 430.14 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... biocides are used must achieve the following effluent limitations representing the degree of effluent... shall be subject to concentration limitations. Concentration limitations are only applicable to non-continuous dischargers. Permittees not using chlorophenolic-containing biocides must certify to the permit...

40 CFR 430.105 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart J [NSPS for secondary fiber non-deink facilities where paperboard from wastepaper is...

40 CFR 430.95 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these biocides: Subpart I [Facilities where fine paper is produced] [NSPS] Pollutant or pollutant property Kg/kkg...

40 CFR 430.65 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.15 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.45 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.65 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.15 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.15 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.35 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.45 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

40 CFR 430.35 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... dischargers, concentration limitations (mg/l) shall apply, where provided. Concentration limitations will only apply to non-continuous dischargers. Only facilities where chlorophenolic-containing biocides are used... chlorophenolic-containing biocides must certify to the permit-issuing authority that they are not using these...

Toxicological Profile of Chlorophenols and Their Derivatives in the Environment: The Public Health Perspective

PubMed Central

Igbinosa, Etinosa O.; Odjadjare, Emmanuel E.; Chigor, Vincent N.; Igbinosa, Isoken H.; Emoghene, Alexander O.; Ekhaise, Fredrick O.; Igiehon, Nicholas O.; Idemudia, Omoruyi G.

2013-01-01

Chlorophenol compounds and their derivatives are ubiquitous contaminants in the environment. These compounds are used as intermediates in manufacturing agricultural chemicals, pharmaceuticals, biocides, and dyes. Chlorophenols gets into the environment from a variety of sources such as industrial waste, pesticides, and insecticides, or by degradation of complex chlorinated hydrocarbons. Thermal and chemical degradation of chlorophenols leads to the formation of harmful substances which constitute public health problems. These compounds may cause histopathological alterations, genotoxicity, mutagenicity, and carcinogenicity amongst other abnormalities in humans and animals. Furthermore, the recalcitrant nature of chlorophenolic compounds to degradation constitutes an environmental nuisance, and a good understanding of the fate and transport of these compounds and their derivatives is needed for a clearer view of the associated risks and mechanisms of pathogenicity to humans and animals. This review looks at chlorophenols and their derivatives, explores current research on their effects on public health, and proffers measures for mitigation. PMID:23690744

Synthetic Chemicals with Potential for Natural Attenuation (Postprint)

DTIC Science & Technology

2012-07-01

The purpose of this paper is to describe examples of other synthetic organic compounds that are known to be biodegradable ...chlorophenols are unusual among the synthetic compounds discussed here in that they can be very toxic to microorganisms . They are often used as biocides...widely distributed. In contract, bacteria able to grow at the expense of chlorinated aliphatic compounds are less common and the

A kinetic study of 3-chlorophenol enhanced hydroxyl radical generation during ozonation.

PubMed

Utsumi, Hideo; Han, Youn-Hee; Ichikawa, Kazuhiro

2003-12-01

Hydroxyl (OH) radical is proposed as an important factor in the ozonation of water. In the present study, the enhancing effect of 3-chlorophenol on OH radical generation was mathematically evaluated using electron spin resonance (ESR)/spin-trapping technique. OH radical was trapped with a 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as a stable adduct, DMPO-OH. The initial velocity of DMPO-OH generation in ozonated water containing 3-chlorophenol was quantitatively measured using a combined system of ESR spectroscopy with stopped-flow apparatus which was controlled by home-made software. The initial velocity of DMPO-OH generation increased as a function of the concentration of ozone and the more effectively of 3-chlorophenol concentration. The relation among ozone concentration, amount of 3-chlorophenol and the initial velocity (nu(0)) of DMPO-OH generation was mathematically analyzed and the following equation was obtained, nu(0) (10(-6)M/s)=[9.7 x [3-chlorophenol (10(-9)M)] + 0.0005]exp(57 x [ozone (10(-9)M)]). The equation fitted very well with the experimental results, and the correlation coefficient was larger than 0.99. The equation for the enhancing effect by 3-chlorophenol should provide useful information to optimize the condition in ozone treatment process of water containing phenolic pollutants.

Consumer exposure to biocides--identification of relevant sources and evaluation of possible health effects.

PubMed

Hahn, Stefan; Schneider, Klaus; Gartiser, Stefan; Heger, Wolfgang; Mangelsdorf, Inge

2010-02-03

Products containing biocides are used for a variety of purposes in the home environment. To assess potential health risks, data on products containing biocides were gathered by means of a market survey, exposures were estimated using a worst case scenario approach (screening), the hazard of the active components were evaluated, and a preliminary risk assessment was conducted. Information on biocide-containing products was collected by on-site research, by an internet inquiry as well as research into databases and lists of active substances. Twenty active substances were selected for detailed investigation. The products containing these substances were subsequently classified by range of application; typical concentrations were derived. Potential exposures were then estimated using a worst case scenario approach according to the European Commission's Technical Guidance Document on Risk Assessment. Relevant combinations of scenarios and active substances were identified. The toxicological data for these substances were compiled in substance dossiers. For estimating risks, the margins of exposure (MOEs) were determined. Numerous consumer products were found to contain biocides. However, it appeared that only a limited number of biocidal active substances or groups of biocidal active substances were being used. The lowest MOEs for dermal exposure or exposure by inhalation were obtained for the following scenarios and biocides: indoor pest control using sprays, stickers or evaporators (chlorpyrifos, dichlorvos) and spraying of disinfectants as well as cleaning of surfaces with concentrates (hydrogen peroxide, formaldehyde, glutardialdehyde). The risk from aggregate exposure to individual biocides via different exposure scenarios was higher than the highest single exposure on average by a factor of three. From the 20 biocides assessed 10 had skin-sensitizing properties. The biocides isothiazolinone (mixture of 5-chloro-2-methyl-2H-isothiazolin-3-one and 2-methyl-2H-isothiazolin-3-one, CMI/MI), glutardialdehyde, formaldehyde and chloroacetamide may be present in household products in concentrations which have induced sensitization in experimental studies. Exposure to biocides from household products may contribute to induction of sensitization in the population. The use of biocides in consumer products should be carefully evaluated. Detailed risk assessments will become available within the framework of the EU Biocides Directive.

Consumer exposure to biocides - identification of relevant sources and evaluation of possible health effects

PubMed Central

2010-01-01

Background Products containing biocides are used for a variety of purposes in the home environment. To assess potential health risks, data on products containing biocides were gathered by means of a market survey, exposures were estimated using a worst case scenario approach (screening), the hazard of the active components were evaluated, and a preliminary risk assessment was conducted. Methods Information on biocide-containing products was collected by on-site research, by an internet inquiry as well as research into databases and lists of active substances. Twenty active substances were selected for detailed investigation. The products containing these substances were subsequently classified by range of application; typical concentrations were derived. Potential exposures were then estimated using a worst case scenario approach according to the European Commission's Technical Guidance Document on Risk Assessment. Relevant combinations of scenarios and active substances were identified. The toxicological data for these substances were compiled in substance dossiers. For estimating risks, the margins of exposure (MOEs) were determined. Results Numerous consumer products were found to contain biocides. However, it appeared that only a limited number of biocidal active substances or groups of biocidal active substances were being used. The lowest MOEs for dermal exposure or exposure by inhalation were obtained for the following scenarios and biocides: indoor pest control using sprays, stickers or evaporators (chlorpyrifos, dichlorvos) and spraying of disinfectants as well as cleaning of surfaces with concentrates (hydrogen peroxide, formaldehyde, glutardialdehyde). The risk from aggregate exposure to individual biocides via different exposure scenarios was higher than the highest single exposure on average by a factor of three. From the 20 biocides assessed 10 had skin-sensitizing properties. The biocides isothiazolinone (mixture of 5-chloro-2-methyl-2H-isothiazolin-3-one and 2-methyl-2H-isothiazolin-3-one, CMI/MI), glutardialdehyde, formaldehyde and chloroacetamide may be present in household products in concentrations which have induced sensitization in experimental studies. Conclusions Exposure to biocides from household products may contribute to induction of sensitization in the population. The use of biocides in consumer products should be carefully evaluated. Detailed risk assessments will become available within the framework of the EU Biocides Directive. PMID:20128903

New environmentally-benign concepts in wood protection: the combination of organic biocides and non-biocidal additives

Treesearch

Frederick Green; Tor P. Schultz

2003-01-01

The principal wood preservative for residential use is currently a broad-spectrum biocide which contains As, Cr and Cu. However, the use of totally organic wood preservative systems in certain applications or localities may be required in the future. This will greatly increase the price of treated wood. The combination of organic biocides with non-biocidal additives to...

Extent of fungal growth on fiberglass duct liners with and without biocides under challenging environmental conditions.

PubMed

Samimi, Behzad S; Ross, Kristen

2003-03-01

Eight brands of fiberglass duct liners, including three that contained biocides, were exposed to challenging environmental conditions that would promote fungal growth. Twenty-four rectangular sheet metal ducts in three groups of eight ducts per group were lined with the eight selected liners. Each group of ducts was exposed to one of the three test conditions within an environmental chamber for a period of 15 days. These conditions were a) 75 percent RH, b) 75 percent RH plus water spray, c) 75 percent RH plus dry nutrient, and d) 75 percent RH plus water plus nutrient. Viable spores of Aspergillus niger were aerosolized into each duct as seed. On the 16th day, air and surface samples for fungal spores were collected from inside ducts. The results of air sampling using N6 sampler and visual inspection indicated that two out of three biocide-containing liners, Permacote and Toughgard, inhibited fungal growth but only under condition A. The third biocide-containing liner, Aeroflex Plus, was effective even when it was wet (conditions A and B). All three biocide-containing liners failed to inhibit fungal growth under conditions C and D. Among the five other types of liners that did not contain biocides, ATCO Flex with a smooth Mylar coating was more preferable, exhibiting lower fungal activity during conditions A, B, and C. All liners failed under condition D when nutrient and water were added together. Surface sampling using adhesive tape failed to produce representative results, apparently due to rough/porous surface of duct liners. It was concluded that duct liners with biocide treatment could be less promoting to microbial growth under high humidity as long as their surfaces remain clean and water-free. A liner with an impermeable and smooth surface seems to be less subject to microbial growth under most conditions than biocide-containing liners having porous and/or rough surfaces.

Effects of Material Choice on Biocide Loss in Orion Water Storage Tanks

NASA Technical Reports Server (NTRS)

Wallace, W. T.; Wallace, S. L.; Gazda, D. B.; Lewis, J. F.

2016-01-01

When preparing for long-duration spaceflight missions, maintaining a safe supply of potable water is of the utmost importance. One major aspect of that is ensuring that microbial growth is minimized. Historically, this challenge has been addressed through the use of biocides. When using biocides, the choice of materials for the storage containers is important, because surface reactions can reduce biocide concentrations below their effective range. In the water storage system baselined for the Orion vehicle, the primary wetted materials are stainless steel (316 L) and a titanium alloy (Ti6Al4V). Previous testing with these materials has shown that the biocide selected for use in the system (ionic silver) will plate out rapidly upon initial wetting of the system. One potential approach for maintaining an adequate biocide concentration is to spike the water supply with high levels of biocide in an attempt to passivate the surface. To evaluate this hypothesis, samples of the wetted materials were tested individually and together to determine the relative loss of biocide under representative surface area-to-volume ratios after 24 hours. Additionally, we have analyzed the efficacy of disinfecting a system containing these materials by measuring reductions in bacterial counts in the same test conditions. Preliminary results indicate that the use of titanium, either individually or in combination with stainless steel, can result in over 95% loss of biocide, while less than 5% is lost when using stainless steel. In bacterial testing, viable organisms were recovered from samples exposed to the titanium coupons after 24 hours. By comparison, no organisms were recovered from the test vessels containing only stainless steel. These results indicate that titanium, while possessing some favorable attributes, may pose additional challenges when used in water storage tanks with ionic silver biocide.

Ecotoxicological Assessment of Immersion Samples from Façade Render Containing Free or Encapsulated Biocides.

PubMed

Vermeirssen, Etiënne L M; Campiche, Sophie; Dietschweiler, Conrad; Werner, Inge; Burkhardt, Michael

2018-05-22

To protect house façades from fouling by microorganisms, biocides can be added to a render or paint before it is applied. During driving rain events, these biocides gradually leach out and have the potential to pollute soil or aquatic ecosystems. We studied the leaching behaviour of biocides and toxicity of leachates from renders with either free or encapsulated biocides. Both render types contained equal amounts of terbutryn, 2-octyl-3(2H)-isothiazolinone (OIT) and 4,5-dichloro-2-n-octyl-4-isothiazolino-3-one (DCOIT). Leachate samples were generated over nine immersion cycles according to a European standard and biocides were quantified. The first and ninth samples were tested using bioassays with algae, bacteria and water flea, the first sample with earthworms and springtails. Encapsulation reduced leaching of terbutryn, OIT and DCOIT four-, 17-, and 27-fold. For aquatic organisms, the toxicity of water from render containing encapsulated biocides was always lower than that of render with free biocides. Furthermore, toxicity decreased four- to five-fold over the nine immersion cycles. Inhibition of photosynthesis was the most sensitive endpoint, followed by algal growth rate, bacterial bioluminescence and water flea reproduction. Toxicity to algae was explained by terbutryn and toxicity to bacteria by OIT. None of the samples affected soil organisms. Results demonstrate that combining standardised leaching tests with standardised bioassays is a promising approach to evaluate the ecotoxicity of biocides that leach from façade renders. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

14 CFR 437.57 - Operating area containment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... containment. (a) During each permitted flight, a permittee must contain its reusable suborbital rocket's..., railway traffic, or waterborne vessel traffic. (c) The FAA may prohibit a reusable suborbital rocket's...

14 CFR 437.57 - Operating area containment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... containment. (a) During each permitted flight, a permittee must contain its reusable suborbital rocket's..., railway traffic, or waterborne vessel traffic. (c) The FAA may prohibit a reusable suborbital rocket's...

14 CFR 437.57 - Operating area containment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... containment. (a) During each permitted flight, a permittee must contain its reusable suborbital rocket's..., railway traffic, or waterborne vessel traffic. (c) The FAA may prohibit a reusable suborbital rocket's...

14 CFR 437.57 - Operating area containment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... containment. (a) During each permitted flight, a permittee must contain its reusable suborbital rocket's..., railway traffic, or waterborne vessel traffic. (c) The FAA may prohibit a reusable suborbital rocket's...

14 CFR 437.57 - Operating area containment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... containment. (a) During each permitted flight, a permittee must contain its reusable suborbital rocket's..., railway traffic, or waterborne vessel traffic. (c) The FAA may prohibit a reusable suborbital rocket's...

Enhanced Biocide Mitigation of Field Biofilm Consortia by a Mixture of D-Amino Acids

PubMed Central

Li, Yingchao; Jia, Ru; Al-Mahamedh, Hussain H.; Xu, Dake; Gu, Tingyue

2016-01-01

Microbiologically influenced corrosion (MIC) is a major problem in the oil and gas industry as well as in many other industries. Current treatment methods rely mostly on pigging and biocide dosing. Biocide resistance is a growing concern. Thus, it is desirable to use biocide enhancers to improve the efficacy of existing biocides. D-Amino acids are naturally occurring. Our previous work demonstrated that some D-amino acids are biocide enhancers. Under a biocide stress of 50 ppm (w/w) hydroxymethyl phosphonium sulfate (THPS) biocide, 1 ppm D-tyrosine and 100 ppm D-methionine used separately successfully mitigated the Desulfovibrio vulgaris biofilm on carbon steel coupons. The data reported in this work revealed that 50 ppm of an equimolar mixture of D-methionine, D-tyrosine, D-leucine, and D-tryptophan greatly enhanced 50 ppm THPS biocide treatment of two recalcitrant biofilm consortia containing sulfate reducing bacteria (SRB), nitrate reducing bacteria (NRB), and fermentative bacteria, etc., from oil-field operations. The data also indicated that individual D-amino acids were inadequate for the biofilm consortia. PMID:27379039

Determining the biofilm penetrating ability of various biocides utilizing an artificial biofilm matrix

DOE Office of Scientific and Technical Information (OSTI.GOV)

McIlwaine, D.B.; Diemer, J.; Grab, L.

1997-12-01

The efficacy of many commonly used biocides is often determined by laboratory evaluations against a variety of planktonic microorganisms. While these tests provide some information as to the performance of a biocide against a particular microorganism, they may not predict how well the biocide will perform under actual field conditions against the more problematic sissile form of the organisms. In order to address the issue of how well a biocide penetrates and kills the problematic microorganisms contained within a biofilm, an artificial biofilm system utilizing microorganisms embedded in alginate beads has been used to compare the efficacy of biocide treatmentsmore » against both the planktonic and sessile form of the same organism. Pure cultures of Enterobacter aerogenes, as well as mixed field isolates, were used in the experiments. In addition, the alginate beads were prepared with actual system waters taken from a variety of industrial applications. In that way, all of the scale and corrosion inhibitors and other contaminants which are present in the actual system are also present in the model biofilm system. In all cases, the organisms contained within the artificial biofilm were significantly more difficult to kill than the corresponding planktonic microbes.« less

Modelling biofilm-induced formation damage and biocide treatment in subsurface geosystems

PubMed Central

Ezeuko, C C; Sen, A; Gates, I D

2013-01-01

Biofilm growth in subsurface porous media, and its treatment with biocides (antimicrobial agents), involves a complex interaction of biogeochemical processes which provide non-trivial mathematical modelling challenges. Although there are literature reports of mathematical models to evaluate biofilm tolerance to biocides, none of these models have investigated biocide treatment of biofilms growing in interconnected porous media with flow. In this paper, we present a numerical investigation using a pore network model of biofilm growth, formation damage and biocide treatment. The model includes three phases (aqueous, adsorbed biofilm, and solid matrix), a single growth-limiting nutrient and a single biocide dissolved in the water. Biofilm is assumed to contain a single species of microbe, in which each cell can be a viable persister, a viable non-persister, or non-viable (dead). Persisters describe small subpopulation of cells which are tolerant to biocide treatment. Biofilm tolerance to biocide treatment is regulated by persister cells and includes ‘innate’ and ‘biocide-induced’ factors. Simulations demonstrate that biofilm tolerance to biocides can increase with biofilm maturity, and that biocide treatment alone does not reverse biofilm-induced formation damage. Also, a successful application of biological permeability conformance treatment involving geologic layers with flow communication is more complicated than simply engineering the attachment of biofilm-forming cells at desired sites. PMID:23164434

Biocidal Efficacy of Dissolved Ozone, Formaldehyde and Sodium Hypochlorite Against Total Planktonic Microorganisms in Produced Water

NASA Astrophysics Data System (ADS)

Puyate, Y. T.; Rim-Rukeh, A.

The performance of three biocides (dissolved ozone, formaldehyde and sodium hypochlorite) in eliminating the bacteria and fungi in produced water is investigated experimentally. The analysis involves monitoring the microbial population in nine conical flasks each containing the same volume of a mixture of produced water, culture medium that sustains the growth of microorganisms and a known concentration of biocide. The concentrations of each biocide used in the study are 0.1, 0.2 and 0.5 ppm. It is shown that dissolved ozone exhibits the best biocidal characteristics and a concentration of 0.5 ppm eliminated all the microorganisms in the produced water after 150 min contact time.

Evaluation of the Biocidal Efficacy of Different Forms of Silver Against Cupriavidus (formerly Wautersia) Species Bacteria

NASA Technical Reports Server (NTRS)

Gazda, Daniel B.; Schultz, John R.; Wong, Wing; Algate, Michelle T.; Bryant, Becky; Castro, Victoria A.

2009-01-01

Contingency Water Containers (CWCs) are used to store potable and technical water that is transferred to the International Space Station (ISS) from the Shuttle orbiter vehicles. When CWCs are filled, water from the orbiter galley is passed through an ion exchange/activated carbon cartridge that removes the residual iodine biocide used on Shuttle before silver biocide is added. Removal of iodine and addition of silver is necessary to inhibit microbial growth inside CWCs and maintain compatibility with the water systems in the Russian segment of ISS. As part of nominal water transfer activities, crewmembers collect samples from several CWCs for postflight analysis. Results from the analysis of water transfer samples collected during the docked phases of STS-118/13A.1 and STS-120/10A showed that several of the CWCs contained up to 10(exp 4) CFU/mL of bacteria despite the fact that the silver concentrations in the CWCs were within acceptable limits. The samples contained pure cultures of a single bacteria, a Cupriavidus (formerly Wautersia) species that has been shown to be resistant to metallic biocides. As part of the investigation into the cause and remediation of the bacterial contamination in these CWCs, ground studies were initiated to evaluate the resistance of the Cupriavidus species to the silver biocides used on ISS and to determine the minimum effective concentration for the different forms of silver present in the biocides. The initial findings from those experiments are discussed herein.

Glass-(nAg, nCu) biocide coatings on ceramic oxide substrates.

PubMed

Esteban-Tejeda, Leticia; Malpartida, Francisco; Díaz, Luis Antonio; Torrecillas, Ramón; Rojo, Fernando; Moya, José Serafín

2012-01-01

The present work was focused on obtaining biocide coatings constituted by a glassy soda-lime matrix containing silver or copper nanoparticles on ceramic (alumina and zirconia based) substrates. Both glassy coatings showed a high biocide activity against Gram-, Gram+ bacteria and yeast, reducing cell numbers more than three logarithms. Silver nanoparticles had a significantly higher biocide activity than copper nanoparticles, since the lixiviation levels required to reduce cell numbers more than 3 logarithms was of almost 1-2 µg/cm(2) in the case of silver nanoparticles, and 10-15 µg/cm(2) for the copper nanoparticles.

Evolution in the Lab: Biocide Resistance in E.coli.

ERIC Educational Resources Information Center

Welden, Charles W.; Hossler, Rex A.

2003-01-01

Describes a laboratory experiment on resistance to teach about evolution and issues of misuse of antimicrobial compounds. Investigates Escherichia coli's response to treatment of triclosan, a biocide used in consumer products. (Contains 12 references.) (YDS)

Regulation of sporicides under the European Biocidal Products Directive.

PubMed

Low, A

2011-03-01

Disinfectants (including sporicides) used in the healthcare setting fall within the scope of the European Biocidal Products Directive (98/8/EC). The active substances used in these products will be evaluated as part of an EU wide review programme, to determine whether they can be used in biocidal products without undue risks to humans, animals and the environment, and that these products will be effective. Following the review of an active substance, biocidal products containing the active substance will become subject to regulatory controls in all EU Member States. This paper discusses how the Directive operates, both through the review programme and the authorisation of biocidal products at the Member State level, together with the requirements to provide data on the efficacy of both the active substances and end-use biocidal products. Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.

Formation of industrial mixed culture biofilm in chlorophenol cultivated medium of microbial fuel cell

NASA Astrophysics Data System (ADS)

Hassan, Huzairy; Jin, Bo; Dai, Sheng; Ngau, Cornelius

2016-11-01

The formation of microbial biofilm while maintaining the electricity output is a challenging topic in microbial fuel cell (MFC) studies. This MFC critical factor becomes more significant when handling with industrial wastewater which normally contains refractory and toxic compounds. This study explores the formation of industrial mixed culture biofilm in chlorophenol cultivated medium through observing and characterizing microscopically its establishment on MFC anode surface. The mixed culture was found to develop its biofilm on the anode surface in the chlorophenol environment and established its maturity and dispersal stages with concurrent electricity generation and phenolic degradation. The mixed culture biofilm engaged the electron transfer roles in MFC by generating current density of 1.4 mA/m2 and removing 53 % of 2,4-dichlorophenol. The results support further research especially on hazardous wastewater treatment using a benign and sustainable method.

Uptake and transformation of phenol and chlorophenols by hairy root cultures of Daucus carota, Ipomoea batatas and Solanum aviculare.

PubMed

de Araujo, Brancilene Santos; Dec, Jerzy; Bollag, Jean Marc; Pletsch, Marcia

2006-04-01

Hairy root cultures of Daucus carota L., Ipomoea batatas L. and Solanum aviculare Forst were investigated for their susceptibility to the highly toxic pollutants phenol and chlorophenols and for the involvement of inherent peroxidases in the removal of phenols from liquid media. Roots of D. carota grew normally in medium containing 1000 micromol l(-1) of phenol, whilst normal growth of roots of I. batatas and S. aviculare was only possible at levels up to 500 micromol l(-1). In the presence of chlorophenols, normal root growth was possible only in concentrations not exceeding 50 micromol l(-1), except for I. batatas which was severely affected at all concentrations. Despite the reduction in biomass, the growth of S. aviculare cultures was sustained in medium containing up to 2000 micromol l(-1) of phenol or 2-chlorophenol, and up to 500 micromol l(-1) of 2,6-dichlorophenol. The amounts of phenol removed by the roots within 72 h of treatment were 72.7%, 90.7% and 98.6% of the initial concentration for D. carota, I. batatas and S. aviculare, respectively. For the removal of 2,6-dichlorophenol the values were, respectively, 83.0%, 57.7% and 73.1%. Phenols labelled with 14C were absorbed by the root tissues and condensed with highly polar cellular substances as well as being incorporated into the cell walls or membranes. The results suggest that S. aviculare, an ornamental plant, would be best suited for remediation trials under field conditions.

Performance of the Tin-Free Antifouling Coating International Ecoloflex in DSTO/RAN Trials

DTIC Science & Technology

2008-10-01

Science and Technology Organisation DSTO-TR-2203 ABSTRACT A national and global ban on the application of antifouling paints containing tributyltin (TBT...Ecoloflex in DSTO/RAN Trials Executive Summary The antifouling biocide tributyltin (TBT) has provided the most effective means of preventing fouling...24 DSTO-TR-2203 1. Introduction Antifouling paints containing tributyltin (TBT) as the primary biocide were

Promising silicones modified with cationic biocides for the development of antimicrobial medical devices.

PubMed

Ghamrawi, Sarah; Bouchara, Jean-Philippe; Tarasyuk, Oksana; Rogalsky, Sergiy; Lyoshina, Lyudmila; Bulko, Olga; Bardeau, Jean-François

2017-06-01

We have tested silicones containing 2% or 5% of the cationic biocides polyhexamethylene guanidine dodecylbenzenesulfonate (PHMG-DBS), 1-octyl-3-methylimidazolium tetrafluoroborate (OMIM-BF 4 ) or 1-dodecyl-3-methylimidazolium tetrafluoroborate (DMIM-BF 4 ) against the major relevant bacterial and yeast species in health care-associated infections (HCAI). Study conducted according to the international standard ISO 22196 revealed that silicones containing 2% or 5% DMIM-BF 4 or 5% PHMG-DBS presented the highest antimicrobial activity, leading to a logarithmic growth reduction of 3.03 to 6.46 and 3.65 to 4.85 depending on the bacterial or fungal species. Heat-pretreated silicones containing 2% DMIM-BF 4 kept a high activity, with at least a 3-log reduction in bacterial growth, except against P. aeruginosa where there was only a 1.1-log reduction. After 33days, the release ratio of cationic biocide from silicone films containing 5% of DMIM-BF 4 was found to be 5.6% in pure water and 1.9% in physiological saline solution, respectively. No leaching of PHMG-DBS polymeric biocide was detected under the same conditions. These results demonstrate unambiguously that silicones containing 2% DMIM-BF 4 or 5% PHMG-DBS present high antimicrobial activity, as well as high leaching resistance and therefore may be good candidates for the development of safer medical devices. Copyright © 2017 Elsevier B.V. All rights reserved.

Effective Synthesis of Sulfate Metabolites of Chlorinated Phenols

PubMed Central

Lehmler, Hans-Joachim; He, Xianran; Li, Xueshu; Duffel, Michael W.; Parkin, Sean

2013-01-01

Chlorophenols are an important class of persistent environmental contaminants and have been implicated in a range of adverse health effects, including cancer. They are readily conjugated and excreted as the corresponding glucuronides and sulfates in the urine of humans and other species. Here we report the synthesis and characterization of a series of ten chlorophenol sulfates by sulfation of the corresponding chlorophenols with 2,2,2-trichloroethyl (TCE) chlorosulfate using N,N-dimethylaminopyridine (DMAP) as base. Deprotection of the chlorophenol diesters with zinc powder/ammonium formate yielded the respective chlorophenol sulfate ammonium salts in good yield. The molecular structure of three TCE-protected chlorophenol sulfate diesters and one chlorophenol sulfate monoester were confirmed by X-ray crystal structure analysis. The chlorophenol sulfates were stable for several months if stored at −20 °C and, thus, are useful for future toxicological, environmental and human biomonitoring studies. PMID:23906814

Crew Exploration Vehicle Potable Water System Verification Description

NASA Technical Reports Server (NTRS)

Tuan, George; Peterson, Laurie J.; Vega, Leticia M.

2010-01-01

A stored water system on the crew exploration vehicle (CEV) will supply the crew with potable water for: drinking and food rehydration, hygiene, medical needs, sublimation, and various contingency situations. The current baseline biocide for the stored water system is ionic silver, similar in composition to the biocide used to maintain the quality of the water, transferred from the orbiter to the International Space Station, stored in contingency water containers. In the CEV water system, a depletion of the ionic silver biocide is expected due to ionic silver-plating onto the surfaces of materials within the CEV water system, thus negating its effectiveness as a biocide. Because this may be the first time NASA is considering a stored water system for long-term missions that do not maintain a residual biocide, a team of experts in materials compatibility, biofilms and point-of-use filters, surface treatment and coatings, and biocides has been created to pinpoint concerns and perform the testing that will help alleviate concerns related to the CEV water system.

Antimicrobial biocides in the healthcare environment: efficacy, usage, policies, and perceived problems.

PubMed

Maillard, Jean-Yves

2005-12-01

Biocides are heavily used in the healthcare environment, mainly for the disinfection of surfaces, water, equipment, and antisepsis, but also for the sterilization of medical devices and preservation of pharmaceutical and medicinal products. The number of biocidal products for such usage continuously increases along with the number of applications, although some are prone to controversies. There are hundreds of products containing low concentrations of biocides, including various fabrics such as linen, curtains, mattresses, and mops that claim to help control infection, although evidence has not been evaluated in practice. Concurrently, the incidence of hospital-associated infections (HAIs) caused notably by bacterial pathogens such as methicillin-resistant Staphylococcus aureus (MRSA) remains high. The intensive use of biocides is the subject of current debate. Some professionals would like to see an increase in their use throughout hospitals, whereas others call for a restriction in their usage to where the risk of pathogen transmission to patients is high. In addition, the possible linkage between biocide and antibiotic resistance in bacteria and the role of biocides in the emergence of such resistance has provided more controversies in their extensive and indiscriminate usage. When used appropriately, biocidal products have a very important role to play in the control of HAIs. This paper discusses the benefits and problems associated with the use of biocides in the healthcare environment and provides a constructive view on their overall usefulness in the hospital setting.

Extended internal standard method for quantitative 1H NMR assisted by chromatography (EIC) for analyte overlapping impurity on 1H NMR spectra.

PubMed

Saito, Naoki; Kitamaki, Yuko; Otsuka, Satoko; Yamanaka, Noriko; Nishizaki, Yuzo; Sugimoto, Naoki; Imura, Hisanori; Ihara, Toshihide

2018-07-01

We devised a novel extended internal standard method of quantitative 1 H NMR (qNMR) assisted by chromatography (EIC) that accurately quantifies 1 H signal areas of analytes, even when the chemical shifts of the impurity and analyte signals overlap completely. When impurity and analyte signals overlap in the 1 H NMR spectrum but can be separated in a chromatogram, the response ratio of the impurity and an internal standard (IS) can be obtained from the chromatogram. If the response ratio can be converted into the 1 H signal area ratio of the impurity and the IS, the 1 H signal area of the analyte can be evaluated accurately by mathematically correcting the contributions of the 1 H signal area of the impurity overlapping the analyte in the 1 H NMR spectrum. In this study, gas chromatography and liquid chromatography were used. We used 2-chlorophenol and 4-chlorophenol containing phenol as an impurity as examples in which impurity and analyte signals overlap to validate and demonstrate the EIC, respectively. Because the 1 H signals of 2-chlorophenol and phenol can be separated in specific alkaline solutions, 2-chlorophenol is suitable to validate the EIC by comparing analytical value obtained by the EIC with that by only qNMR under the alkaline condition. By the EIC, the purity of 2-chlorophenol was obtained with a relative expanded uncertainty (k = 2) of 0.24%. The purity matched that obtained under the alkaline condition. Furthermore, the EIC was also validated by evaluating the phenol content with the absolute calibration curve method by gas chromatography. Finally, we demonstrated that the EIC was possible to evaluate the purity of 4-chlorophenol, with a relative expanded uncertainty (k = 2) of 0.22%, which was not able to be separated from the 1 H signal of phenol under any condition. Copyright © 2018 Elsevier B.V. All rights reserved.

Aspects of cooling tower biocides and protozoa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berk, S.G.; Ashburn, R.J.; Ting, R.S.

1998-12-31

Previous work has shown that certain cooling tower amoebae and ciliated protozoa are resistant to several cooling tower biocides, even at the manufacturer`s recommended dosages. For the present study, an Acunthumoeba species was isolated from a cooling tower in Australia. Suspensions of the trophozoites (feeding stages) were exposed to isothiazolones. Cysts were tested separately. The minimum lethal concentration (MLC) for trophozoites was between 31-62 ppm of the biocide product, which is slightly less than the MLC for an amoebae species from the United States; and cyst forms were twofold more resistant than those of the US species, with a MLCmore » of 62,500 ppm. A ciliate and an amoeba species were also exposed to bromochlorodimethylhydantoin. The MLC for the ciliate species was 1 ppm of the biocide product, and the MLC was 30--40 ppm for the amoeba trophozoites. Since amoebae can expel vesicles containing live Legionella, experiments were conducted to determine whether exposure of Acunthamoebu polyphugu to biocides influenced release of such potentially infectious particles. Vesicle release was not inhibited by any of the three biocides: quaternary ammonium compounds (QACs), isothiazolones, and a thiocarbamate compound. These results suggest that amoebae from various sources are resistant to recommended levels of biocides, and the amoebae may continue to release potentially infectious vesicles in the presence of biocides.« less

Information technologies in public health management: a database on biocides to improve quality of life.

PubMed

Roman, C; Scripcariu, L; Diaconescu, Rm; Grigoriu, A

2012-01-01

Biocides for prolonging the shelf life of a large variety of materials have been extensively used over the last decades. It has estimated that the worldwide biocide consumption to be about 12.4 billion dollars in 2011, and is expected to increase in 2012. As biocides are substances we get in contact with in our everyday lives, access to this type of information is of paramount importance in order to ensure an appropriate living environment. Consequently, a database where information may be quickly processed, sorted, and easily accessed, according to different search criteria, is the most desirable solution. The main aim of this work was to design and implement a relational database with complete information about biocides used in public health management to improve the quality of life. Design and implementation of a relational database for biocides, by using the software "phpMyAdmin". A database, which allows for an efficient collection, storage, and management of information including chemical properties and applications of a large quantity of biocides, as well as its adequate dissemination into the public health environment. The information contained in the database herein presented promotes an adequate use of biocides, by means of information technologies, which in consequence may help achieve important improvement in our quality of life.

Waste Isolation Pilot Plant (WIPP) fact sheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-10-01

Pursuant to the Solid Waste Disposal Act, as amended by the Resource Conservation and Recovery Act (RCRA), as amended (42 USC 6901, et seq.), and the New Mexico Hazardous Waste Act (Section 74-4-1 et seq., NMSA 1978), Permit is issued to the owner and operator of the US DOE, WIPP site (hereafter called the Permittee(s)) to operate a hazardous waste storage facility consisting of a container storage unit (Waste Handling Building) and two Subpart X miscellaneous below-ground storage units (Bin Scale Test Rooms 1 and 3), all are located at the above location. The Permittee must comply with all termsmore » and conditions of this Permit. This Permit consists of the conditions contained herein, including the attachments. Applicable regulations cited are the New Mexico Hazardous Waste Management Regulations, as amended 1992 (HWMR-7), the regulations that are in effect on the date of permit issuance. This Permit shall become effective upon issuance by the Secretary of the New Mexico Environment Department and shall be in effect for a period of ten (10) years from issuance. This Permit is also based on the assumption that all information contained in the Permit application and the administrative record is accurate and that the activity will be conducted as specified in the application and the administrative record. The Permit application consists of Revision 3, as well as associated attachments and clarifying information submitted on January 25, 1993, and May 17, 1993.« less

Suitability of small environmental chambers to test the emission of biocides from treated materials into the air

NASA Astrophysics Data System (ADS)

Horn, Wolfgang; Jann, Oliver; Wilke, Olaf

Biocides are used to protect materials that might be damaged by fungal, microbial or insect activity. The aim of this study is to develop a method for the measurement of these organic compounds, which generally have low or moderate vapor pressures. The biocides considered in this study are permethrin, dichlofluanid, tolylfluanid, iodpropinylbutylcarbamat, octylisothiazolinone, tebuconazole and propiconazole. The emission from two commercial products (plastic foil, wool carpet) containing biocides and of seven types of biocidal formulations applied to wood or clay tiles were investigated in 20-l glass emission test chambers. Each chamber test was performed over a period of 100-200 days, and one investigation was conducted over several years. Compared to volatile organic compounds, low-volatility compounds show totally different emission curves in chamber tests; maximal emission values may be reached in days or weeks. A period of 3 months is sometimes necessary for the determination of area-specific emission rates (SER a's). The SER a's (μg m -2 h -1) from biocide-containing products were determined for permethrin (0.006), propiconazole (0.3), dichlofluanid (2.0), tolylfluanid (1.0), octylisothiazolinone (2.5) and iodpropinylbutylcarbamat (2). In most cases, the SER a stayed at its maximum value or declined slowly over the test period. Additionally, a chamber test begun in 1994 with a piece of wood treated with a typical mixture of biocides dissolved in a technical solvent was continued. SER a's (μg m -2 h -1) for dichlofluanid (0.20), tebuconazole (0.49) and permethrin (0.08) remained detectable after the period of nearly 9 years during which the sample remained continuously in the chamber. This test proved the very slow decrease of emission of low-volatility compounds like permethrin and tebuconazole.

Bactericidal Specificity and Resistance Profile of Poly(Quaternary Ammonium) Polymers and Protein-Poly(Quaternary Ammonium) Conjugates.

PubMed

Ji, Weihang; Koepsel, Richard R; Murata, Hironobu; Zadan, Sawyer; Campbell, Alan S; Russell, Alan J

2017-08-14

Antibacterial polymers are potentially powerful biocides that can destroy bacteria on contact. Debate in the literature has surrounded the mechanism of action of polymeric biocides and the propensity for bacteria to develop resistance to them. There has been particular interest in whether surfaces with covalently coupled polymeric biocides have the same mechanism of action and resistance profile as similar soluble polymeric biocides. We designed and synthesized a series of poly(quaternary ammonium) polymers, with tailorable molecular structures and architectures, to engineer their antibacterial specificity and their ability to delay the development of bacterial resistance. These linear poly(quaternary ammonium) homopolymers and block copolymers, generated using atom transfer radical polymerization, had structure-dependent antibacterial specificity toward Gram positive and negative bacterial species. When single block copolymers contained two polymer segments of differing antibacterial specificity, the polymer combined the specificities of its two components. Nanoparticulate human serum albumin-poly(quaternary ammonium) conjugates of these same polymers, synthesized via "grafting from" atom transfer radical polymerization, were strongly biocidal and also exhibited a marked decrease in the rate of bacterial resistance development relative to linear polymers. These protein-biocide conjugates mimicked the behavior of surface-presented polycationic biocides rather than their nonproteinaceous counterparts.

Antimicrobial biocides in the healthcare environment: efficacy, usage, policies, and perceived problems

PubMed Central

Maillard, Jean-Yves

2005-01-01

Biocides are heavily used in the healthcare environment, mainly for the disinfection of surfaces, water, equipment, and antisepsis, but also for the sterilization of medical devices and preservation of pharmaceutical and medicinal products. The number of biocidal products for such usage continuously increases along with the number of applications, although some are prone to controversies. There are hundreds of products containing low concentrations of biocides, including various fabrics such as linen, curtains, mattresses, and mops that claim to help control infection, although evidence has not been evaluated in practice. Concurrently, the incidence of hospital-associated infections (HAIs) caused notably by bacterial pathogens such as methicillin-resistant Staphylococcus aureus (MRSA) remains high. The intensive use of biocides is the subject of current debate. Some professionals would like to see an increase in their use throughout hospitals, whereas others call for a restriction in their usage to where the risk of pathogen transmission to patients is high. In addition, the possible linkage between biocide and antibiotic resistance in bacteria and the role of biocides in the emergence of such resistance has provided more controversies in their extensive and indiscriminate usage. When used appropriately, biocidal products have a very important role to play in the control of HAIs. This paper discusses the benefits and problems associated with the use of biocides in the healthcare environment and provides a constructive view on their overall usefulness in the hospital setting. PMID:18360573

Leaching of biocides from building facades: Upscaling of a local two-region leaching model to the city scale

NASA Astrophysics Data System (ADS)

Coutu, S.; Rota, C.; Rossi, L.; Barry, D. A.

2011-12-01

Facades are protected by paints that contain biocides as protection against degradation. These biocides are leached by rainfall (albeit at low concentrations). At the city scale, however, the surface area of building facades is significant, and leached biocides are a potential environmental risk to receiving waters. A city-scale biocide-leaching model was developed based on two main steps. In the first step, laboratory experiments on a single facade were used to calibrate and validate a 1D, two-region phenomenological model of biocide leaching. The same data set was analyzed independently by another research group who found empirically that biocide leachate breakthrough curves were well represented by a sum of two exponentials. Interestingly, the two-region model was found analytically to reproduce this functional form as a special case. The second step in the method is site-specific, and involves upscaling the validated single facade model to a particular city. In this step, (i) GIS-based estimates of facade heights and areas are deduced using the city's cadastral data, (ii) facade flow is estimated using local meteorological data (rainfall, wind direction) and (iii) paint application rates are modeled as a stochastic process based on manufacturers' recommendations. The methodology was applied to Lausanne, Switzerland, a city of about 200,000 inhabitants. Approximately 30% of the annually applied mass of biocides was estimated to be released to the environment.

Development of an energy-saving anaerobic hybrid membrane bioreactors for 2-chlorophenol-contained wastewater treatment.

PubMed

Wang, Yun-Kun; Pan, Xin-Rong; Sheng, Guo-Ping; Li, Wen-Wei; Shi, Bing-Jing; Yu, Han-Qing

2015-12-01

A novel energy-saving anaerobic hybrid membrane bioreactor (AnHMBR) with mesh filter, which takes advantage of anaerobic membrane bioreactor and fixed-bed biofilm reactor, is developed for low-strength 2-chlorophenol (2-CP)-contained wastewater treatment. In this system, the anaerobic membrane bioreactor is stuffed with granular activated carbon to construct an anaerobic hybrid fixed-bed biofilm membrane bioreactor. The effluent turbidity from the AnHMBR system was low during most of the operation period, and the chemical oxygen demand and 2-CP removal efficiencies averaged 82.3% and 92.6%, respectively. Furthermore, a low membrane fouling rate was achieved during the operation. During the AnHMBR operation, the only energy consumption was for feed pump. And a low energy demand of 0.0045-0.0063kWhm(-3) was estimated under the current operation conditions. All these results demonstrated that this novel AnHMBR is a sustainable technology for treating 2-CP-contained wastewater. Copyright © 2014 Elsevier Ltd. All rights reserved.

9 CFR 112.2 - Final container label, carton label, and enclosure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... biological product which name shall be identical with that shown in the product license under which such... container label if complete descriptive terms appear on a carton label and enclosures; (2) If the biological... if the biological product is prepared in a foreign country, the name and address of the permittee and...

9 CFR 112.2 - Final container label, carton label, and enclosure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... biological product which name shall be identical with that shown in the product license under which such... container label if complete descriptive terms appear on a carton label and enclosures; (2) If the biological... if the biological product is prepared in a foreign country, the name and address of the permittee and...

9 CFR 112.2 - Final container label, carton label, and enclosure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... biological product which name shall be identical with that shown in the product license under which such... container label if complete descriptive terms appear on a carton label and enclosures; (2) If the biological... if the biological product is prepared in a foreign country, the name and address of the permittee and...

9 CFR 112.2 - Final container label, carton label, and enclosure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... biological product which name shall be identical with that shown in the product license under which such... container label if complete descriptive terms appear on a carton label and enclosures; (2) If the biological... if the biological product is prepared in a foreign country, the name and address of the permittee and...

40 CFR 270.42 - Permit modification at the request of the permittee.

Code of Federal Regulations, 2014 CFR

2014-07-01

... storage in tanks or containers, or in containment buildings in accordance with 40 CFR part 268; (C) To...) Performance Track member facilities. The following procedures apply to Performance Track member facilities... Track member facilities must have complied with the requirements of § 264.15(b)(5) in order to request a...

40 CFR 270.42 - Permit modification at the request of the permittee.

Code of Federal Regulations, 2011 CFR

2011-07-01

... storage in tanks or containers, or in containment buildings in accordance with 40 CFR part 268; (C) To...) Performance Track member facilities. The following procedures apply to Performance Track member facilities... Track member facilities must have complied with the requirements of § 264.15(b)(5) in order to request a...

40 CFR 270.42 - Permit modification at the request of the permittee.

Code of Federal Regulations, 2013 CFR

2013-07-01

... storage in tanks or containers, or in containment buildings in accordance with 40 CFR part 268; (C) To...) Performance Track member facilities. The following procedures apply to Performance Track member facilities... Track member facilities must have complied with the requirements of § 264.15(b)(5) in order to request a...

40 CFR 270.42 - Permit modification at the request of the permittee.

Code of Federal Regulations, 2012 CFR

2012-07-01

... storage in tanks or containers, or in containment buildings in accordance with 40 CFR part 268; (C) To...) Performance Track member facilities. The following procedures apply to Performance Track member facilities... Track member facilities must have complied with the requirements of § 264.15(b)(5) in order to request a...

Metal-containing and related polymers for biomedical applications.

PubMed

Yan, Yi; Zhang, Jiuyang; Ren, Lixia; Tang, Chuanbing

2016-10-07

A survey of the most recent progress in the biomedical applications of metal-containing polymers is given. Due to the unique optical, electrochemical, and magnetic properties, at least 30 different metal elements, most of them transition metals, are introduced into polymeric frameworks for interactions with biology-relevant substrates via various means. Inspired by the advance of metal-containing small molecular drugs and promoted by the great progress in polymer chemistry, metal-containing polymers have gained momentum during recent decades. According to their different applications, this review summarizes the following biomedical applications: (1) metal-containing polymers as drug delivery vehicles; (2) metal-containing polymeric drugs and biocides, including antimicrobial and antiviral agents, anticancer drugs, photodynamic therapy agents, radiotherapy agents and biocides; (3) metal-containing polymers as biosensors, and (4) metal-containing polymers in bioimaging.

Relationship of Triamine-Biocide Tolerance of Salmonella enterica Serovar Senftenberg to Antimicrobial Susceptibility, Serum Resistance and Outer Membrane Proteins.

PubMed

Futoma-Kołoch, Bożena; Dudek, Bartłomiej; Kapczyńska, Katarzyna; Krzyżewska, Eva; Wańczyk, Martyna; Korzekwa, Kamila; Rybka, Jacek; Klausa, Elżbieta; Bugla-Płoskońska, Gabriela

2017-07-11

A new emerging phenomenon is the association between the incorrect use of biocides in the process of disinfection in farms and the emergence of cross-resistance in Salmonella populations. Adaptation of the microorganisms to the sub-inhibitory concentrations of the disinfectants is not clear, but may result in an increase of sensitivity or resistance to antibiotics, depending on the biocide used and the challenged Salmonella serovar. Exposure of five Salmonella enterica subsp. enterica serovar Senftenberg ( S. Senftenberg) strains to triamine-containing disinfectant did not result in variants with resistance to antibiotics, but has changed their susceptibility to normal human serum (NHS). Three biocide variants developed reduced sensitivity to NHS in comparison to the sensitive parental strains, while two isolates lost their resistance to serum. For S. Senftenberg, which exhibited the highest triamine tolerance (6 × MIC) and intrinsic sensitivity to 22.5% and 45% NHS, a downregulation of flagellin and enolase has been demonstrated, which might suggest a lower adhesion and virulence of the bacteria. This is the first report demonstrating the influence of biocide tolerance on NHS resistance. In conclusion, there was a potential in S. Senftenberg to adjust to the conditions, where the biocide containing triamine was present. However, the adaptation did not result in the increase of antibiotic resistance, but manifested in changes within outer membrane proteins' patterns. The strategy of bacterial membrane proteins' analysis provides an opportunity to adjust the ways of infection treatments, especially when it is connected to the life-threating bacteremia caused by Salmonella species.

Relationship of Triamine-Biocide Tolerance of Salmonella enterica Serovar Senftenberg to Antimicrobial Susceptibility, Serum Resistance and Outer Membrane Proteins

PubMed Central

Futoma-Kołoch, Bożena; Dudek, Bartłomiej; Kapczyńska, Katarzyna; Wańczyk, Martyna; Korzekwa, Kamila; Rybka, Jacek; Klausa, Elżbieta; Bugla-Płoskońska, Gabriela

2017-01-01

A new emerging phenomenon is the association between the incorrect use of biocides in the process of disinfection in farms and the emergence of cross-resistance in Salmonella populations. Adaptation of the microorganisms to the sub-inhibitory concentrations of the disinfectants is not clear, but may result in an increase of sensitivity or resistance to antibiotics, depending on the biocide used and the challenged Salmonella serovar. Exposure of five Salmonella enterica subsp. enterica serovar Senftenberg (S. Senftenberg) strains to triamine-containing disinfectant did not result in variants with resistance to antibiotics, but has changed their susceptibility to normal human serum (NHS). Three biocide variants developed reduced sensitivity to NHS in comparison to the sensitive parental strains, while two isolates lost their resistance to serum. For S. Senftenberg, which exhibited the highest triamine tolerance (6 × MIC) and intrinsic sensitivity to 22.5% and 45% NHS, a downregulation of flagellin and enolase has been demonstrated, which might suggest a lower adhesion and virulence of the bacteria. This is the first report demonstrating the influence of biocide tolerance on NHS resistance. In conclusion, there was a potential in S. Senftenberg to adjust to the conditions, where the biocide containing triamine was present. However, the adaptation did not result in the increase of antibiotic resistance, but manifested in changes within outer membrane proteins’ patterns. The strategy of bacterial membrane proteins’ analysis provides an opportunity to adjust the ways of infection treatments, especially when it is connected to the life-threating bacteremia caused by Salmonella species. PMID:28696348

Chemical Interactions of Hydraulic Fracturing Biocides with Natural Pyrite

NASA Astrophysics Data System (ADS)

Consolazio, Nizette A.

In conjunction with horizontal drilling, hydraulic fracturing or fracking has enabled the recovery of natural gas from low permeable shale formations. In addition to water, these fracking fluids employ proppants and up to 38 different chemical additives to improve the efficiency of the process. One important class of additives used in hydraulic fracturing is biocides. When applied appropriately, they limit the growth of harmful microorganisms within the well, saving energy producers 4.5 billion dollars each year. However, biocides or their harmful daughter products may return to the surface in produced water, which must then be appropriately stored, treated and disposed of. Little is known about the effect of mineral-fluid interactions on the fate of the biocides employed in hydraulic fracturing. In this study, we employed laboratory experiments to determine changes in the persistence and products of these biocides under controlled environments. While many minerals are present in shale formations, pyrite, FeS2(s) is particularly interesting because of its prevalence and reactivity. The FeII groups on the face of pyrite may be oxidized to form FeIII phases. Both of these surfaces have been shown to be reactive with organic compounds. Chlorinated compounds undergo redox reactions at the pyrite-fluid interface, and sulfur-containing compounds undergo exceptionally strong sorption to both pristine and oxidized pyrite. This mineral may significantly influence the degradation of biocides in the Marcellus Shale. Thus, the overall goal of this study was to understand the effect of pyrite on biocide reactivity in hydraulic fracturing, focusing on the influence of pyrite on specific functional groups. The first specific objective was to demonstrate the effect of pyrite and pyrite reaction products on the degradation of the bromine-containing biocide, DBNPA. On the addition of pyrite to DBNPA, degradation rates of the doubly brominated compound were found to increase significantly. DBNPA is proposed to undergo redox reactions with the pyrite surface, accepting two-electrons from pyrite, and thus becoming reduced. The primary product is the monobrominated analogue of DBNPA, 2-monobromo-3-nitrilopropionamide (or MBNPA). The surface area-normalized first-order initial degradation rate constant was found to be 5.1 L.m-2day-1. It was also determined that the dissolution and oxidation products of pyrite, Fe II, S2O32- and SO4 2- are unlikely to contribute to the reduction of the biocide. Taken together, the results illustrate that a surface reaction with pyrite has the ability to reduce the persistence of DBNPA, and as a consequence change the distribution of its reaction products. The second objective was to quantify the influence of water chemistry and interactions with pyrite on the degradation of the sulfur-containing biocide. Dazomet readily hydrolyzes in water due to the nucleophilic attack of hydroxide (OH-) anions. Thus the half-life of dazomet during the shut-in phase of hydraulic fracturing will decrease with increasing pH: 8.5 hours at pH 4.1 to 3.4 hours at pH 8.2.Dazomet degradation was rapidly accelerated upon exposure to the oxidized pyrite surface, reacting five times faster than hydrolysis in the absence of pyrite at a similar pH. The products measured were identical to those identified on hydrolysis (methyl isothiocyanate and formaldehyde) and no dissolved iron was detected in solutions. This suggests that the dithiocarbamate group in dazomet was able to chemisorb onto the oxidized pyrite surface, shifting the electron density of the molecule which resulted in accelerated hydrolysis of the biocide. The third objective explored the reactivity of various biocide functional groups due to the addition of pyrite. Several elimination mechanisms were identified, and tied to the reactivity of the specific functional group involved. The addition of pyrite led to accelerated degradation of dibromodicyanobutane. This is because the bromine (-Br) group is easily reduced. For methylene bis(thiocyanate), hydrolysis was a noteworthy elimination mechanism since the thiocyanate (-SCN) functionality is a good leaving group. Benzisothiazolinone and methyl isothiazolinone were stable at low pH due to the stabilizing donor-acceptor interactions between the organic biocides' carbonyl (-C=O) groups and salts in the solution. This body of work has illustrated that pristine pyrite can undergo redox reactions with brominated biocides used in hydraulic fracturing, reducing their persistence and altering the product distribution. This will change the efficacy and the risks associated with the use of these biocides in shales containing pyrite, particularly at lower pH where organic compounds are more stable to hydrolysis. However, at higher pH hydrolysis becomes more important, and additional studies will need to be conducted to investigate the pyrite contribution under these conditions. Conversely, the FeIII surface groups on oxidized pyrite can catalyze the hydrolysis of dazomet and may do so for other labile, sulfur-containing biocides as well. Overall, this research has shown that the physicochemical properties (such as the acid dissociation constant and the standard reduction potential) that govern the environmental reactivity of a molecule can be used to anticipate its reactivity in hydraulic fracturing.

25 CFR 166.214 - Will the BIA notify the permittee of any change in land title status?

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false Will the BIA notify the permittee of any change in land... AND WATER GRAZING PERMITS Permit Requirements General Requirements § 166.214 Will the BIA notify the permittee of any change in land title status? Yes. We will notify the permittee if a fee patent is issued or...

Sorption of chlorophenols on microporous minerals: mechanism and influence of metal cations, solution pH, and humic acid.

PubMed

Yang, Hui; Hu, Yuanan; Cheng, Hefa

2016-10-01

Sorption of 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), and 2,4,6-trichlorophenol (2,4,6-TCP) on a range of dealuminated zeolites were investigated to understand the mechanism of their sorption on microporous minerals, while the influence of common metal cations, solution pH, and humic acid was also studied. Sorption of chlorophenols was found to increase with the hydrophobicity of the sorbates and that of the microporous minerals, indicating the important role of hydrophobic interactions, while sorption was also stronger in the micropores of narrower sizes because of greater enhancement of the dispersion interactions. The presence of metal cations could enhance chlorophenol sorption due to the additional electrostatic attraction between metal cations exchanged into the mineral micropores and the chlorophenolates, and this effect was apparent on the mineral sorbent with a high density of surface cations (2.62 sites/nm(2)) in its micropores. Under circum-neutral or acidic conditions, neutral chlorophenol molecules adsorbed into the hydrophobic micropores through displacing the "loosely bound" water molecules, while their sorption was negligible under moderately alkaline conditions due to electrostatic repulsion between the negatively charged zeolite framework and anionic chlorophenolates. The influence of humic acid on sorption of chlorophenols on dealuminated Y zeolites suggests that its molecules did not block the micropores but created a secondary sorption sites by forming a "coating layer" on the external surface of the zeolites. These mechanistic insights could help better understand the interactions of ionizable chlorophenols and metal cations in mineral micropores and guide the selection and design of reusable microporous mineral sorbents for sorptive removal of chlorophenols from aqueous stream.

Study on US/O3 mechanism in p-chlorophenol decomposition

PubMed Central

Xu, Xian-wen; Xu, Xin-hua; Shi, Hui-xiang; Wang, Da-hui

2005-01-01

Study on the effects of sonolysis, ozonolysis and US/O3 system on the decomposition of p-chlorophenol in aqueous solutions indicated that in the cases of US/O3 system, individual ozonolysis and sonolysis, the decomposition rate of p-chlorophenol reached 78.78%, 56.20%, 2.79% after a 16-min reaction while its CODcr (chemical oxygen demand) removal rate was 97.02%, 62.17%, 3.67% after a 120-min reaction. The decomposition reaction of p-chlorophenol follows pseudo-first-order kinetics. The enhancement factors of p-chlorophenol and its CODcr under US/O3 system reached 63% and 237% respectively. The main intermediates during the decomposition include catechol, hydroquinone, p-benzoquinone, phenol, fumaric acid, maleic acid, oxalic acid and formic acid. The decomposition mechanism of p-chlorophenol was also discussed. PMID:15909343

Oxidative Degradation of Chlorophenolic Compounds with Modified-Fenton Process Using Pyrite as the Catalyst

NASA Astrophysics Data System (ADS)

Kantar, Cetin; Urken, Ozge; Oral, Ozlem; Kaplan, Iremsu; Ayman Oz, Nilgun

2017-04-01

Oxidative dehalogenation has been shown to be a viable and cost effective process for dealing with a particularly persistent class of contaminants (e.g., chlorophenolic compounds (CP)) often found in contaminated soil and ground water. Here, the degradation of various chlorophenolic compounds (e.g., 2-CP, 4-CP, 2,3-di CP, 2,4-di CP, 2,4,6-tri CP, 2,3,4,6-Tetra CP) was investigated by modified Fenton process using pyrite as source of Fe2+ (catalyst) . The effects of different parameters such as chlorophenol type, pH and chlorophenol, pyrite and H2O2 concentrations on the degradation kinetics of chlorophenols were studied in batch reactors. Our results show that while the rate of chloropehenol degradation increased with decreasing solution pH, no direct correlation was observed between H2O2 concentration and chlorophenol degradation, indicating a complex mechanism involved in CP degradation by modified Fenton process. The batch results also show that the CP degradation was highly dependent on CP type, the number and location of chloride ions in the structure. Overall, the results of this study suggest that pyrite can be effectively used in reactive treatment barriers for in-situ treatment of subsurface systems contaminated with chlorophenols.

The corrosion behaviour of galvanized steel in cooling tower water containing a biocide and a corrosion inhibitor.

PubMed

Minnoş, Bihter; Ilhan-Sungur, Esra; Çotuk, Ayşın; Güngör, Nihal Doğruöz; Cansever, Nurhan

2013-01-01

The corrosion behaviour of galvanized steel in cooling tower water containing a biocide and a corrosion inhibitor was investigated over a 10-month period in a hotel. Planktonic and sessile numbers of sulphate reducing bacteria (SRB) and heterotrophic bacteria were monitored. The corrosion rate was determined by the weight loss method. The corrosion products were analyzed by energy dispersive X-ray spectroscopy and X-ray diffraction. A mineralized, heterogeneous biofilm was observed on the coupons. Although a biocide and a corrosion inhibitor were regularly added to the cooling water, the results showed that microorganisms, such as SRB in the mixed species biofilm, caused corrosion of galvanized steel. It was observed that Zn layers on the test coupons were completely depleted after 3 months. The Fe concentrations in the biofilm showed significant correlations with the weight loss and carbohydrate concentration (respectively, p < 0.01 and p < 0.01).

Biocidal Properties of Anti-Icing Additives for Aircraft Fuels

PubMed Central

Neihof, R. A.; Bailey, C. A.

1978-01-01

The biocidal and biostatic activities of seven glycol monoalkyl ether compounds were evaluated as part of an effort to find an improved anti-icing additive for jet aircraft fuel. Typical fuel contaminants, Cladosporium resinae, Gliomastix sp., Candida sp., Pseudomonas aeruginosa, and a mixed culture containing sulfate-reducing bacteria were used as assay organisms. Studies were carried out over 3 to 4 months in two-phase systems containing jet fuel and aqueous media. Diethylene glycol monomethyl ether, triethylene glycol monomethyl ether, triethylene glycol monoethyl ether, and 2-methoxyethanol were generally biocidal in aqueous concentrations of 10 to 17% for all organisms except Gliomastix, which required 25% or more. 2-Ethoxyethanol, 2-propoxyethanol, and 2-butoxyethanol were biocidal at progressively lower concentrations down to 1 to 2% for 2-butoxyethanol. The enhanced antimicrobial activity of these three compounds was attributed to cytoplasmic membrane damage because of the correlation between surface tension measurements and lytic activity with P. aeruginosa cells. The mechanism of action of the less active compounds appeared to be due to osmotic (dehydrating) effects. When all requirements are taken into account, diethylene glycol monomethyl ether appears to be the most promising replacement for the currently used additive, 2-methoxyethanol. PMID:646356

Reductive dehalogenation of chlorophenols by Desulfomonile tiedjei DCB-1.

PubMed Central

Mohn, W W; Kennedy, K J

1992-01-01

Reductive dehalogenation of chlorophenols has been reported in undefined anaerobic cultures but never before in an anaerobic pure culture. We found that the sulfate-reducing bacterium Desulfomonile tiedjei DCB-1 reductively dehalogenates pentachlorophenol (PCP) and other chlorophenols. The maximum rate of PCP dechlorination observed was 54 mu mol of Cl- h-1 g of protein-1. 3-Chlorobenzoate appeared to serve as a required inducer for PCP dehalogenation; however, neither PCP nor 3-chlorophenol induced dehalogenation. Dehalogenation was catalyzed by living cells, and formate served as a required electron donor. D. tiedjei dehalogenated meta-chlorine substituents of chlorophenols (i.e., PCP was degraded to 2,4,6-trichlorophenol). Generally, more highly chlorinated phenol congeners were more readily dechlorinated, and 3-chlorophenol was not dehalogenated. Growing cultures dehalogenated PCP, but greater than 10 microM PCP (approximately 1.7 mmol g of protein-1) reversibly inhibited growth. PMID:1599254

[Concentration of biocides in indoor rooms using pyrethroids as an example].

PubMed

Walker, G; Keller, R; Beckert, J; Butte, W

1994-06-01

Pyrethroids are an analogous substance group to one of the oldest known, naturally occurring insecticides pyrethrum and have replaced a number of pesticides such as Lindane, DDT and PCP on the market. Biocides are more persistent indoors than in nature, which could lead to permanent health hazards for the people concerned. Within a few days after application pyrethroids are rarely detected in room air but can be traced for a long time on textiles, furniture and in dust particles (3, 8). The investigation results of approx. 100 analyses from dust and carpet samples show that approx. 1/3 of these samples are positive for at least one pyrethroid and contain a concentration of > 2 mg substance per kg sample. The evaluation of 35 air samples taken from rooms where substances containing pyrethroids had been used at least a month prior to the investigation (the samples were sampled on active charcoal or Chromosorb) showed that pyrethroids could no longer be traced above the detection limit of 0.05-0.1 micrograms/m3. We therefore think that when investigating a contamination of rooms by biocides it is more advisable to determine pyrethroid and its synergists in the suspended dust portion and corresponding dust sample rather than analysing air by adsorption to active charcoal, Chromosorb or other carrier materials. From the observed concentrations of biocides one could conclude that in an indoor setting secondary contamination by biocides plays a more significant role in the total-body-load than that of air contamination.

Degradation of aqueous phenol solutions by coaxial DBD reactor

NASA Astrophysics Data System (ADS)

Dojcinovic, B. P.; Manojlovic, D.; Roglic, G. M.; Obradovic, B. M.; Kuraica, M. M.; Puric, J.

2008-07-01

Solutions of 2-chlorophenol, 4-chlorophenol and 2,6-dichlorophenol in bidistilled and water from the river Danube were treated in plasma reactor. In this reactor, based on coaxial dielectric barrier discharge at atmospheric pressure, plasma is formed over a thin layer of treated water. After one pass through the reactor, starting chlorophenols concentration of 20 mg/l was diminished up to 95 %. Kinetics of the chlorophenols degradation was monitored by High Pressure Liquid Chromatography method (HPLC).

[Biodegradation characteristics of o-chlorophenol with photosynthetic bacteria PSB-1D].

PubMed

Hu, Xiao-min; Dong, Yi-hu; Li, Liang; Lu, Juan; He, Ying-dian; Gao, Yang

2010-07-01

A strain of photosynthetic bacteria named PSB-1D with degradation of o-chlorophenol (2-CP) was isolated and screened from the shallow substrate sludge in downstream side of the sewage outfall of an insecticide factory. The PSB-1D is identified preliminarily as Rhodopseudomonas sp. according to its colony and cell morphological properties, physiological biochemical characteristics and absorption spectrum analysis of living cells. The experiments results of relationship between PSB-1D growth and o-chlorophenol degradation showed that the degradation rate of o-chlorophenol was up to 57.26% after 7 days cultural time. The main environmental factors including way of illumination and oxygen, initial pH, cultural temperature, illumination intensity had distinctly influenced on the o-chlorophenol degradation with PSB-1D. The results showed that the optimum conditions were as following: an anaerobic light, pH 7.0, temperature 30 degrees C, illumination intensity 4000 lx,initial o-chlorophenol concentration 50 mg/L. Under that cultural condition, the degradation rate of o-chlorophenol could reach to 62.08%. The degradation kinetic data fitted the Andrews model well. In addition, the biodegradation process of o-chlorophenol can be well described by enzymatic reaction of high concentration inhibition, with the maximum substrate utilization rate 0.309 d(-1), Michaelis-Menten constant 2.733 mg/L, inhibitory constant 230.15 mg/L respectively.

Crew Exploration Vehicle (CEV) Potable Water System Verification Description

NASA Technical Reports Server (NTRS)

Peterson, Laurie; DeVera, Jean; Vega, Leticia; Adam, Nik; Steele, John; Rector, Tony; Gazda, Daniel; Roberts, Michael

2008-01-01

The Crew Exploration Vehicle (CEV), also known as Orion, will ferry a crew of up to six astronauts to the International Space Station (ISS), or a crew of up to four astronauts to the moon. The first launch of CEV is scheduled for approximately 2014. A stored water system on the CEV will supply the crew with potable water for various purposes: drinking and food rehydration, hygiene, medical needs, sublimation, and various contingency situations. The current baseline biocide for the stored water system is ionic silver, similar in composition to the biocide used to maintain quality of the water transferred from the Orbiter to the ISS and stored in Contingency Water Containers (CWCs). In the CEV water system, the ionic silver biocide is expected to be depleted from solution due to ionic silver plating onto the surfaces of the materials within the CEV water system, thus negating its effectiveness as a biocide. Since the biocide depletion is expected to occur within a short amount of time after loading the water into the CEV water tanks at the Kennedy Space Center (KSC), an additional microbial

Environmental monitoring of bleached kraft pulp mill chlorophenolic compounds in a northern Canadian river system.

PubMed

Owens, J W; Swanson, S M; Birkholz, D A

1994-07-01

The environmental transport of pulp mill effluent compounds and the exposure of two fish species has been monitored by parallel analyses of effluent, water column and suspended sediment samples, and fish bile and muscle. Compounds analyzed included over 20 chlorophenolic compounds and 12 fatty and resin acids. The concentration of chlorophenols varied with seasonal river flows and mill process changes such as the substitution of chlorine dioxide (ClO2) for chlorine gas (Cl2) in the bleach plant. At 100% (ClO2) substitution, the effluent and the water column concentrations of most chlorophenolics approached the analytical detection limits of 0.1-1 parts per billion. Chlorophenolic and fatty/resin acid compounds were detected in the bile of both mountain whitefish (Prosopium williamsoni) and longnose sucker (Catostomus catostomus), but were rarely detected in fillets. Fish bile concentrations were observed in an apparent spatial gradient as far as 230 km downstream of the mill. A depuration experiment with fish held in uncontaminated water for eight days indicated a rapid decrease in chlorophenol levels. These observations corroborate previous investigations that chlorophenolic compounds are rapidly excreted and can be used as sensitive markers for recent exposure to mill effluents.

Comparative cytotoxicity of chlorophenols to cultured fish cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saito, Hotaka; Shigeoka, Tadayoshi

1994-10-01

In vitro cytotoxicity of chlorophenols to Cyprinus carpio brain (CCB) cells derived from carp and Oryzias latipes fin (OLF-136) cells derived from medaka was examined with the neutral red (3-amino-7-dimethylamino-2-methylphenazine hydrochloride) incorporation assay. Results were compared with previous cytotoxicity data of chlorophenols to goldfish (Carassius auratus) scale (GFS) cells derived from the goldfish. There were excellent correlations between the 24-h NR50 values of chlorophenols toward the three kinds of cells (r[sup 2] > 0.94).

10 CFR 1016.34 - Accountability for Secret Restricted Data.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Accountability for Secret Restricted Data. 1016.34 Section... Information § 1016.34 Accountability for Secret Restricted Data. Each permittee possessing documents containing Secret Restricted Data shall establish a document accountability procedure and shall maintain...

10 CFR 1016.34 - Accountability for Secret Restricted Data.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Accountability for Secret Restricted Data. 1016.34 Section... Information § 1016.34 Accountability for Secret Restricted Data. Each permittee possessing documents containing Secret Restricted Data shall establish a document accountability procedure and shall maintain...

10 CFR 1016.34 - Accountability for Secret Restricted Data.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 4 2013-01-01 2013-01-01 false Accountability for Secret Restricted Data. 1016.34 Section... Information § 1016.34 Accountability for Secret Restricted Data. Each permittee possessing documents containing Secret Restricted Data shall establish a document accountability procedure and shall maintain...

10 CFR 1016.34 - Accountability for Secret Restricted Data.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Accountability for Secret Restricted Data. 1016.34 Section... Information § 1016.34 Accountability for Secret Restricted Data. Each permittee possessing documents containing Secret Restricted Data shall establish a document accountability procedure and shall maintain...

10 CFR 1016.34 - Accountability for Secret Restricted Data.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Accountability for Secret Restricted Data. 1016.34 Section... Information § 1016.34 Accountability for Secret Restricted Data. Each permittee possessing documents containing Secret Restricted Data shall establish a document accountability procedure and shall maintain...

Chlorophenol sorption on multi-walled carbon nanotubes: DFT modeling and structure-property relationship analysis.

PubMed

Watkins, Marquita; Sizochenko, Natalia; Moore, Quentarius; Golebiowski, Marek; Leszczynska, Danuta; Leszczynski, Jerzy

2017-02-01

The presence of chlorophenols in drinking water can be hazardous to human health. Understanding the mechanisms of adsorption under specific experimental conditions would be beneficial when developing methods to remove toxic substances from drinking water during water treatment in order to limit human exposure to these contaminants. In this study, we investigated the sorption of chlorophenols on multi-walled carbon nanotubes using a density functional theory (DFT) approach. This was applied to study selected interactions between six solvents, five types of nanotubes, and six chlorophenols. Experimental data were used to construct structure-adsorption relationship (SAR) models that describe the recovery process. Specific interactions between solvents and chlorophenols were taken into account in the calculations by using novel specific mixture descriptors.

50 CFR 3.3 - Discrimination by contractors and permittees prohibited.

Code of Federal Regulations, 2013 CFR

2013-10-01

... permittees prohibited. 3.3 Section 3.3 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR GENERAL PROVISIONS NONDISCRIMINATION-CONTRACTS, PERMITS, AND USE OF FACILITIES § 3.3 Discrimination by contractors and permittees prohibited. The provisions of part III of Executive...

50 CFR 3.3 - Discrimination by contractors and permittees prohibited.

Code of Federal Regulations, 2014 CFR

2014-10-01

... permittees prohibited. 3.3 Section 3.3 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR GENERAL PROVISIONS NONDISCRIMINATION-CONTRACTS, PERMITS, AND USE OF FACILITIES § 3.3 Discrimination by contractors and permittees prohibited. The provisions of part III of Executive...

50 CFR 3.3 - Discrimination by contractors and permittees prohibited.

Code of Federal Regulations, 2012 CFR

2012-10-01

... permittees prohibited. 3.3 Section 3.3 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR GENERAL PROVISIONS NONDISCRIMINATION-CONTRACTS, PERMITS, AND USE OF FACILITIES § 3.3 Discrimination by contractors and permittees prohibited. The provisions of part III of Executive...

50 CFR 3.3 - Discrimination by contractors and permittees prohibited.

Code of Federal Regulations, 2010 CFR

2010-10-01

... permittees prohibited. 3.3 Section 3.3 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR GENERAL PROVISIONS NONDISCRIMINATION-CONTRACTS, PERMITS, AND USE OF FACILITIES § 3.3 Discrimination by contractors and permittees prohibited. The provisions of part III of Executive...

50 CFR 3.3 - Discrimination by contractors and permittees prohibited.

Code of Federal Regulations, 2011 CFR

2011-10-01

... permittees prohibited. 3.3 Section 3.3 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR GENERAL PROVISIONS NONDISCRIMINATION-CONTRACTS, PERMITS, AND USE OF FACILITIES § 3.3 Discrimination by contractors and permittees prohibited. The provisions of part III of Executive...

Microreactor of Pd nanoparticles immobilized hollow microspheres for catalytic hydrodechlorination of chlorophenols in water.

PubMed

Lan, Yang; Yang, Li; Zhang, Minchao; Zhang, Wangqing; Wang, Shengnan

2010-01-01

A microreactor of Pd nanoparticles immobilized shell-corona hollow microspheres of poly[styrene-co-2-(acetoacetoxy) ethyl methacrylate-co-acrylamide] has been designed for catalytic hydrodechlorination (HDC) of chlorophenols in the sole solvent of water. The strategy of the combined use of the shell-corona hollow microspheres as microcapsule and catalyst scaffold endues the microreactor several advantages. First, the microreactor can be dispersed in the sole solvent of water and acts as a quasi-homogeneous catalyst for catalytic HDC of chlorophenols. Second, the reactant of chlorophenols can be highly concentrated within the hollow microspheres of the microreactor in the sole solvent of water. Third, the resultant product of phenol can be favorably excreted off the microreactor into water because of the polar difference between the reactant of chlorophenols and the product of phenol. Ascribed to the combined advantages, catalytic HDC of chlorophenols can be performed efficiently within the microreactor in the sole solvent of water at room temperature under atmosphere pressure.

ANAEROBIC/AEROBIC BIODEGRADATION OF PENTACHLOROPHENOL USING GAC FLUIDIXED BED REACTORS: OPTIMIZATION OF THE EMPTY BED CONTACT TIME

EPA Science Inventory

An integrated reactor system has been developed to remediate pentachlorophenol (PCP) containing wastes using sequential anaerobic and aerobic biodegradation. Anaerobically, PCP was degraded to approximately equimolar concentrations (>99%) of chlorophenol (CP) in a granular activa...

36 CFR 20.3 - Maximum number of permittees.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Maximum number of permittees... INTERIOR ISLE ROYALE NATIONAL PARK; COMMERCIAL FISHING § 20.3 Maximum number of permittees. Commercial fishermen to whom the annual revocable permits may be granted shall not exceed the maximum number of persons...

[Health risks from pest control products].

PubMed

Pieper, C; Holthenrich, D; Schneider, H

2014-05-01

According to European biocide legislation, pest control products require assessment and authorization by the responsible national or European authorities. Biocidal products can only be authorized if they have no unacceptable effects on human health. The health risk assessment performed for authorization comprises (a) the derivation of reference values for the active substances and substances of concern contained in the biocidal product and (b) an exposure assessment. These parameters are required for risk characterization. No unacceptable health risks are expected if the determined exposure is less than the relevant reference value. In addition, the toxicological information is used for classification of the biocidal product. The assessment may, where necessary, result in specific conditions for use or other restrictions aimed at minimizing risk. The risk to human health from pest control products is mainly based on the toxicological properties of their active substances. Commonly, the coformulants used in pest control products are of less concern than the active substances (e.g., food ingredients and animal feed products). For example, most rodenticides belong to the group of anticoagulants, which are also effective in humans. Regarding intoxications through insecticides, the group of pyrethroids is of particular importance. Fumigants containing metal phosphides, hydrogen cyanide, or sulfuryl difluoride are particularly toxic. This toxicity is linked to the high acute inhalation toxicity of the gaseous active substances themselves or, in the case of phosphides, of the released gas phosphane. The aim of health risk assessment for the authorization of biocidal products is to ensure their safe application for users and all other persons involved, assuming an adequate and label-compliant use.

Biofilm Inhibition by Novel Natural Product- and Biocide-Containing Coatings Using High-Throughput Screening.

PubMed

Salta, Maria; Dennington, Simon P; Wharton, Julian A

2018-05-10

The use of natural products (NPs) as possible alternative biocidal compounds for use in antifouling coatings has been the focus of research over the past decades. Despite the importance of this field, the efficacy of a given NP against biofilm (mainly bacteria and diatoms) formation is tested with the NP being in solution, while almost no studies test the effect of an NP once incorporated into a coating system. The development of a novel bioassay to assess the activity of NP-containing and biocide-containing coatings against marine biofilm formation has been achieved using a high-throughput microplate reader and highly sensitive confocal laser scanning microscopy (CLSM), as well as nucleic acid staining. Juglone, an isolated NP that has previously shown efficacy against bacterial attachment, was incorporated into a simple coating matrix. Biofilm formation over 48 h was assessed and compared against coatings containing the NP and the commonly used booster biocide, cuprous oxide. Leaching of the NP from the coating was quantified at two time points, 24 h and 48 h, showing evidence of both juglone and cuprous oxide being released. Results from the microplate reader showed that the NP coatings exhibited antifouling efficacy, significantly inhibiting biofilm formation when compared to the control coatings, while NP coatings and the cuprous oxide coatings performed equally well. CLSM results and COMSTAT analysis on biofilm 3D morphology showed comparable results when the NP coatings were tested against the controls, with higher biofilm biovolume and maximum thickness being found on the controls. This new method proved to be repeatable and insightful and we believe it is applicable in antifouling and other numerous applications where interactions between biofilm formation and surfaces is of interest.

25 CFR 161.206 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2011 CFR

2011-04-01

... exposure to disease? 161.206 Section 161.206 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... permittee do to protect livestock from exposure to disease? In accordance with applicable law, permittees... infectious diseases; and (c) Restrict the movement of exposed or infected livestock. ...

25 CFR 161.206 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2010 CFR

2010-04-01

... exposure to disease? 161.206 Section 161.206 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... permittee do to protect livestock from exposure to disease? In accordance with applicable law, permittees... infectious diseases; and (c) Restrict the movement of exposed or infected livestock. ...

25 CFR 161.206 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2012 CFR

2012-04-01

... exposure to disease? 161.206 Section 161.206 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... permittee do to protect livestock from exposure to disease? In accordance with applicable law, permittees... infectious diseases; and (c) Restrict the movement of exposed or infected livestock. ...

25 CFR 161.206 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2014 CFR

2014-04-01

... exposure to disease? 161.206 Section 161.206 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... permittee do to protect livestock from exposure to disease? In accordance with applicable law, permittees... infectious diseases; and (c) Restrict the movement of exposed or infected livestock. ...

25 CFR 161.206 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2013 CFR

2013-04-01

... exposure to disease? 161.206 Section 161.206 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... permittee do to protect livestock from exposure to disease? In accordance with applicable law, permittees... infectious diseases; and (c) Restrict the movement of exposed or infected livestock. ...

10 CFR 1016.8 - Approval for processing access permittees for security facility approval.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Approval for processing access permittees for security facility approval. 1016.8 Section 1016.8 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) SAFEGUARDING OF RESTRICTED DATA Physical Security § 1016.8 Approval for processing access permittees for security facility...

10 CFR 1016.8 - Approval for processing access permittees for security facility approval.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Approval for processing access permittees for security facility approval. 1016.8 Section 1016.8 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) SAFEGUARDING OF RESTRICTED DATA Physical Security § 1016.8 Approval for processing access permittees for security facility...

Evaluation of biocidal efficacy of copper alloy coatings in comparison with solid metal surfaces: generation of organic copper phosphate nanoflowers.

PubMed

Gutierrez, H; Portman, T; Pershin, V; Ringuette, M

2013-03-01

To analyse the biocidal efficacy of thermal sprayed copper surfaces. Copper alloy sheet metals containing >60% copper have been shown to exhibit potent biocidal activity. Surface biocidal activity was assessed by epifluorescence microscopy. After 2-h exposure at 20 °C in phosphate-buffered saline (PBS), contact killing of Gram-negative Escherichia coli and Gram-positive Staphylococcus epidermidis by brass sheet metal and phosphor bronze was 3-4-times higher than that by stainless steel. SEM observations revealed that the surface membranes of both bacterial strains were slightly more irregular when exposed to brass sheet metal than stainless steel. However, when exposed to phosphor bronze coating, E. coli were 3-4 times larger with irregular membrane morphology. In addition, the majority of the cells were associated with spherical carbon-copper-phosphate crystalline nanostructures characteristic of nanoflowers. The membranes of many of the S. epidermidis exhibited blebbing, and a small subset was also associated with nanoflowers. Our data indicate that increasing the surface roughness of copper alloys had a pronounced impact on the membrane integrity of Gram-positive and, to a lesser degree, Gram-negative bacteria. In the presence of PBS, carbon-copper-phosphate-containing nanoflowers were formed, likely nucleated by components derived from killed bacteria. The intimate association of the bacteria with the nanoflowers and phosphor bronze coating likely contributed to their nonreversible adhesion. Thermal spraying of copper alloys provides a strategy for the rapid coating of three-dimensional organic and inorganic surfaces with biocidal copper alloys. Our study demonstrates that the macroscale surface roughness generated by the thermal spray process enhances the biocidal activity of copper alloys compared with the nanoscale surface roughness of copper sheet metals. Moreover, the coating surface topography provides conditions for the rapid formation of organic copper phosphate nanocrystals/nanoflowers. © 2012 The Society for Applied Microbiology.

Laboratory observations of biocide efficiency against Legionella in model cooling tower systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, W.M.; Eccles, J.; Fricker, C.

1999-07-01

The efficacy of specific oxidizing and non-oxidizing biocides was examined using a model cooling system inoculated with a microcosm containing an environmental isolate of Legionella pneumophila. The microcosm was prepared in a two-stage chemostat, which provided a consistent source of microbiological inoculum for the study. The microcosm consisted of both sessile (within biofilms) and planktonic Legionella in association with other microorganisms, including Pseudomonas species and cyst-forming ameobae. A procedure was established to successfully transfer the chemostat grown inoculum to the model cooling system and establish both sessile and planktonic forms of Legionella in the model cooling system. The greatest biocidalmore » effect for all of the biocides was observed immediately after dosing. This effect was relatively short-lived even for the slow acting biocides such isothiazolin (as 8 ppm active) where an effect was only observed over the first 12 hours. The faster acting biocides, DBNPA (as 8 ppm active) and gluteraldehyde (as 27 ppm active), did initially reduce Legionella populations but did not totally eliminate Legionella or provide lasting control. Chlorine and bromine (as 0.5--1.5 ppm free halogen), and ozone (as 0.1--0.5 ppm free reserve) reduced and controlled Legionella populations so long as a free reserve of oxidant was maintained. Legionella recovered quickly after biocide dosing, reestablishing similar levels to those observed before dosing.« less

36 CFR 228.47 - General terms and conditions of contracts and permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of improvements. (e) Use of existing National Forest development roads. The authorized officer may require purchasers and permittees to obtain appropriate road-use permits, make deposits for or perform their commensurate share of road maintenance, and comply with road-use rules contained in 36 CFR part...

Anaerobic biodegradation of phenolic compounds in digested sludge.

PubMed Central

Boyd, S A; Shelton, D R; Berry, D; Tiedje, J M

1983-01-01

We examined the anaerobic degradation of phenol and the ortho, meta, and para isomers of chlorophenol, methoxyphenol, methylphenol (cresol), and nitrophenol in anaerobic sewage sludge diluted to 10% in a mineral salts medium. Of the 12 monosubstituted phenols studied, only p-chlorophenol and o-cresol were not significantly degraded during an 8-week incubation period. The phenol compounds degraded and the time required for complete substrate disappearance (in weeks) were: phenol (2), o-chlorophenol (3), m-chlorophenol (7), o-methoxyphenol (2), m- and p-methoxyphenol (1), m-cresol (7), p-cresol (3), and o-, m-, and p-nitrophenol (1). Complete mineralization of phenol, o-chlorophenol, m-cresol, p-cresol, o-nitrophenol, p-nitrophenol, and o-, m-, and p-methoxyphenol was observed. In general, the presence of Cl and NO2 groups on phenols inhibited methane production. Elimination or transformation of these substituents was accompanied by increased methane production, o-Chlorophenol was metabolized to phenol, which indicated that dechlorination was the initial degradation step. The methoxyphenols were transformed to the corresponding dihydroxybenzene compounds, which were subsequently mineralized. PMID:6614908

DETERMINATION OF PHENOLS IN ENVIRONMENTALLY RELEVANT MATRICES WITH THE USE OF LIQUID CHROMATOGRAPHY WITH AN ENZYME ELECTRODE DETECTOR

EPA Science Inventory

A simple and rapid assay using HPLC with a tyrosinase-containing carbon paste electrode (Tyr-CPE) detector is demonstrated for the detection of phenol, p-cresol, p-methoxyphenol, and p-chlorophenol in environmental matrices. These compounds were measured in contaminated aqueous...

7 CFR 319.24-4 - Notice of arrival of corn by permittee.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Notice of arrival of corn by permittee. 319.24-4... HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FOREIGN QUARANTINE NOTICES Corn Diseases Regulations Governing Entry of Indian Corn Or Maize § 319.24-4 Notice of arrival of corn by permittee. Immediately upon...

7 CFR 319.24-4 - Notice of arrival of corn by permittee.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Notice of arrival of corn by permittee. 319.24-4... HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FOREIGN QUARANTINE NOTICES Corn Diseases Regulations Governing Entry of Indian Corn Or Maize § 319.24-4 Notice of arrival of corn by permittee. Immediately upon...

40 CFR 270.42 - Permit modification at the request of the permittee.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; and (vi) The following statement: “The permittee's compliance history during the life of the permit... can be viewed and copied; and (vi) The following statement: “The permittee's compliance history during... purpose of technology changes needed to meet the standards under 40 CFR 63.1203, 63.1204, and 63.1205. (2...

Encapsulation of Antifouling Organic Biocides in Poly(lactic acid) Nanoparticles.

PubMed

Kamtsikakis, Aristotelis; Kavetsou, Eleni; Chronaki, Konstantina; Kiosidou, Evangelia; Pavlatou, Evangelia; Karana, Alexandra; Papaspyrides, Constantine; Detsi, Anastasia; Karantonis, Antonis; Vouyiouka, Stamatina

2017-09-26

The scope of the current research was to assess the feasibility of encapsulating three commercial antifouling compounds, Irgarol 1051, Econea and Zinc pyrithione, in biodegradable poly(lactic acid) (PLA) nanoparticles. The emulsification-solvent evaporation technique was herein utilized to manufacture nanoparticles with a biocide:polymer ratio of 40%. The loaded nanoparticles were analyzed for their size and size distribution, zeta potential, encapsulation efficiency and thermal properties, while the relevant physicochemical characteristics were correlated to biocide-polymer system. In addition, the encapsulation process was scaled up and the prepared nanoparticles were dispersed in a water-based antifouling paint in order to examine the viability of incorporating nanoparticles in such coatings. Metallic specimens were coated with the nanoparticles-containing paint and examined regarding surface morphology.

Chlorophenols in marine organisms from the southern coast of Hangzhou Bay, China, and an assessment of risks posed to human health

NASA Astrophysics Data System (ADS)

Zheng, Dan; Jiao, Haifeng; Zhong, Huiying; Qiu, Jishi; Yan, Xiaojun; Duan, Qingyuan; Chai, Liyue

2017-06-01

The composition of chlorophenols in marine organisms from the southern coast of Hangzhou Bay, China, was analyzed and the health risks posed to humans assessed. A total of 19 chlorophenols from 16 types of marine organism were analyzed across nine survey sections in Hangzhou Bay. The chlorophenols were analyzed by gas chromatography-mass spectrometry using a DB-5MS quartz capillary column. The concentrations of monochlorophenol, dichlorophenol, trichlorophenol, tetrachlorophenol, and pentachlorophenol ranged from below the detection limit (ND) to 132 μg/kg, ND-51.0 μg/kg, ND-42.5 μg/kg, ND-69.0 μg/kg, and ND-9.06 μg/kg, respectively. Additionally, concentration differences between each type of chlorophenol were not signifi cant (P>0.05). However, signifi cant differences were found between monochlorophenol (F=8.13, P<0.01) and total chlorophenol (F=5.19, P<0.01) concentrations. As the noncarcinogenic risk indices were <0.1 (10-5-10-2) for all of the organisms, no high risk was posed by 2-chlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol, 2,4,5-trichlorophenol, 2,3,4,6-tetrachlorophenol, and pentachlorophenol to humans consuming marine organisms from the study area. Furthermore, the carcinogenic risks posed by 2,4,6-trichlorophenol and pentachlorophenol were lower than limits set by the International Commission on Radiological Protection and the US Environmental Protection Agency. However, the noncarcinogenic and carcinogenic risks posed by chlorophenols in marine organisms from four of the survey sections (Sizaopu, Niluoshan, Longshan Town and Xinhong zha) were higher than the other survey sections.

Biodegradation of 4-chlorophenol by adsorptive immobilized Alcaligenes sp. A 7-2 in soil.

PubMed

Balfanz, J; Rehm, H J

1991-08-01

Alcaligenes sp. A 7-2 immobilized on granular clay has been applied in a percolator to degrade 4-chlorophenol in sandy soil. Good adsorption rates on granular clay were achieved using cell suspensions with high titres and media at pH 8.0. The influence of various parameters such as aeration rate, pH, temperature, concentration of 4-chlorophenol and size of inoculum on the degradation rate were investigated. During fed-batch fermentations under optimal culture conditions, concentrations of 4-chlorophenol up to 160 mg.l-1 could be degraded. Semicontinuous culture experiments demonstrated that the degradation potential in soil could be well established and enhanced by the addition of immobilized bacteria. Continuous fermentation was performed with varying 4-chlorophenol concentrations in the feed and different input levels. The maximum degradation rate was 1.64 g.l-1.day-1.

43 CFR 2812.4-3 - Agreements and arbitration between permittee and licensee respecting adjustment of road use.

Code of Federal Regulations, 2012 CFR

2012-10-01

... permittee and licensee respecting adjustment of road use. 2812.4-3 Section 2812.4-3 Public Lands: Interior... RESOURCE MANAGEMENT (2000) TRAMROADS AND LOGGING ROADS Over O. and C. and Coos Bay Revested Lands § 2812.4-3 Agreements and arbitration between permittee and licensee respecting adjustment of road use. (a...

43 CFR 2812.4-3 - Agreements and arbitration between permittee and licensee respecting adjustment of road use.

Code of Federal Regulations, 2014 CFR

2014-10-01

... permittee and licensee respecting adjustment of road use. 2812.4-3 Section 2812.4-3 Public Lands: Interior... RESOURCE MANAGEMENT (2000) TRAMROADS AND LOGGING ROADS Over O. and C. and Coos Bay Revested Lands § 2812.4-3 Agreements and arbitration between permittee and licensee respecting adjustment of road use. (a...

43 CFR 2812.4-3 - Agreements and arbitration between permittee and licensee respecting adjustment of road use.

Code of Federal Regulations, 2013 CFR

2013-10-01

... permittee and licensee respecting adjustment of road use. 2812.4-3 Section 2812.4-3 Public Lands: Interior... RESOURCE MANAGEMENT (2000) TRAMROADS AND LOGGING ROADS Over O. and C. and Coos Bay Revested Lands § 2812.4-3 Agreements and arbitration between permittee and licensee respecting adjustment of road use. (a...

43 CFR 2812.4-3 - Agreements and arbitration between permittee and licensee respecting adjustment of road use.

Code of Federal Regulations, 2011 CFR

2011-10-01

... permittee and licensee respecting adjustment of road use. 2812.4-3 Section 2812.4-3 Public Lands: Interior... RESOURCE MANAGEMENT (2000) TRAMROADS AND LOGGING ROADS Over O. and C. and Coos Bay Revested Lands § 2812.4-3 Agreements and arbitration between permittee and licensee respecting adjustment of road use. (a...

25 CFR 161.704 - What can a permittee do if they receive a trespass notice?

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false What can a permittee do if they receive a trespass notice... NAVAJO PARTITIONED LANDS GRAZING PERMITS Trespass Notification § 161.704 What can a permittee do if they receive a trespass notice? The trespasser will within the time frame specified in the notice: (a) Comply...

25 CFR 161.704 - What can a permittee do if they receive a trespass notice?

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true What can a permittee do if they receive a trespass notice... NAVAJO PARTITIONED LANDS GRAZING PERMITS Trespass Notification § 161.704 What can a permittee do if they receive a trespass notice? The trespasser will within the time frame specified in the notice: (a) Comply...

25 CFR 161.704 - What can a permittee do if they receive a trespass notice?

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false What can a permittee do if they receive a trespass notice... NAVAJO PARTITIONED LANDS GRAZING PERMITS Trespass Notification § 161.704 What can a permittee do if they receive a trespass notice? The trespasser will within the time frame specified in the notice: (a) Comply...

25 CFR 161.704 - What can a permittee do if they receive a trespass notice?

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false What can a permittee do if they receive a trespass notice... NAVAJO PARTITIONED LANDS GRAZING PERMITS Trespass Notification § 161.704 What can a permittee do if they receive a trespass notice? The trespasser will within the time frame specified in the notice: (a) Comply...

25 CFR 161.704 - What can a permittee do if they receive a trespass notice?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false What can a permittee do if they receive a trespass notice... NAVAJO PARTITIONED LANDS GRAZING PERMITS Trespass Notification § 161.704 What can a permittee do if they receive a trespass notice? The trespasser will within the time frame specified in the notice: (a) Comply...

Photocatalytic activity of porous multiwalled carbon nanotube-TiO2 composite layers for pollutant degradation.

PubMed

Zouzelka, Radek; Kusumawati, Yuly; Remzova, Monika; Rathousky, Jiri; Pauporté, Thierry

2016-11-05

TiO2 nanoparticles are suitable building blocks nanostructures for the synthesis of porous functional thin films. Here we report the preparation of films using brookite, P25 titania and anatase pristine nanoparticles and of nanocomposite layers combining anatase nanoparticles and multi-walled carbon nanotube (MWCNT) at various concentrations. The structure and phase composition of the layers were characterized by X-ray diffraction and Raman spectroscopy. Their morphology and texture properties were determined by scanning electron microscopy and krypton adsorption experiments, respectively. Additionally to a strong absorption in the UV range, the composites exhibited light absorption in the visible range as well. The photocatalytic performance of the layers was tested in the degradation of aqueous solutions of 4-chlorophenol serving as a model of an eco-persistent pollutant. Besides the determination of the decrease in the concentration of 4-chlorophenol, also the formation of intermediate degradation products, namely hydroquinone and benzoquinone, was followed. The presence of MWCNTs had a beneficial effect on the photocatalytic performance, a marked increase in the photocatalytic degradation rate constant being observed even at very low concentrations of MWCNTs. Compared to a P25 reference layer, the first order rate reaction constant increased by about 100% for the composite films containing MWCNTs at concentrations above 0.6 wt%. The key parameters for the enhancement of the photocatalytic performance are discussed. The presence of carbon nanotubes influences beneficially the degradation of 4-chlorophenol by an attack of the primarily photoproduced hydroxyl radicals onto the 4-chlorophenol molecules. The degradation due to the direct charge transfer is practically not influenced at all. Copyright © 2016 Elsevier B.V. All rights reserved.

Removal of 2,4-dichlorophenol and pentachlorophenol from waters by sorption using coal fly ash from a Portuguese thermal power plant.

PubMed

Estevinho, Berta N; Martins, Isabel; Ratola, Nuno; Alves, Arminda; Santos, Lúcia

2007-05-08

Chlorophenols are one of the most important groups of priority pollutants, due to their high toxicity, mutagenicity and carcinogenicity. Although activated carbon has been the preferred choice for the removal of such pollutants from wastewaters, the search for cheaper alternative sorbents became common in the last years. Fly ash, a by-product from coal burning power plants, has a surface composition that may enable the sorption of specific organic compounds. Therefore, this feasibility study presents the optimization of the operating parameters of a fixed-bed column containing fly ash particles, percolated by aqueous solutions of 2,4-dichlorophenol (2,4-DCP) and pentachlorophenol (PCP) with concentrations of 1 and 100 microg/ml. Both chlorophenols were analysed by gas chromatography with electron capture detection (GC-ECD), after solid-phase microextraction (SPME), with limits of detection (LODs) of 7.28 microg/l for 2,4-DCP and 1.76 microg/l for PCP. Removal efficiencies above 99% were obtained for an initial concentration of 10 microg/ml of chlorophenols. Column saturation was achieved after 7h of continuous operation for 2,4-DCP and 10h for the PCP for feed levels of 10 microg/ml. Fly ash exhibited more affinity towards the sorption of PCP, in comparison to 2,4-DCP.

47 CFR 73.3526 - Local public inspection file of commercial stations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... or at its proposed main studio. (2) A television station licensee or applicant that had a Web site... inspection file containing the material, relating to that station, described in paragraphs (e)(2) and (e)(10... pending. If the application is granted, paragraph (a)(2) of this section shall apply. (2) Every permittee...

47 CFR 73.3526 - Local public inspection file of commercial stations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or at its proposed main studio. (2) A television station licensee or applicant that had a Web site... inspection file containing the material, relating to that station, described in paragraphs (e)(2) and (e)(10... pending. If the application is granted, paragraph (a)(2) of this section shall apply. (2) Every permittee...

Efflux pump induction by quaternary ammonium compounds and fluoroquinolone resistance in bacteria.

PubMed

Buffet-Bataillon, Sylvie; Tattevin, Pierre; Maillard, Jean-Yves; Bonnaure-Mallet, Martine; Jolivet-Gougeon, Anne

2016-01-01

Biocides, primarily those containing quaternary ammonium compounds (QAC), are heavily used in hospital environments and various industries (e.g., food, water, cosmetic). To date, little attention has been paid to potential implications of QAC use in the emergence of antibiotic resistance, especially fluoroquinolone-resistant bacteria in patients and in the environment. QAC-induced overexpression of efflux pumps can lead to: cross resistance with fluoroquinolones mediated by multidrug efflux pumps; stress response facilitating mutation in the Quinolone Resistance Determining Region; and biofilm formation increasing the risk of transfer of mobile genetic elements carrying fluoroquinolone or QAC resistance determinants. By following the European Biocidal Product Regulation, manufacturers of QAC are required to ensure that their QAC-based biocidal products are safe and will not contribute to emerging bacterial resistance.

Update on antibacterial soaps: the FDA takes a second look at triclosans.

PubMed

Bergstrom, Kendra Gail

2014-04-01

In December of 2013 the Food and Drug Administration announced it would look further into the safety and efficacy of the biocide triclosan and requested further safety data as part of a new review with the Environmental Protection Agency. The use of triclosan has increased exponentially since its introduction in in 1972, to the point that 75% of commercial soap brands contain triclosan and 76% of a nationwide sample of adults and children excrete triclosan in the urine. This announcement raised an important dialog about the appropriate use of all over the counter biocides. Particular concerns include whether these biocides are more effective than regular soaps, whether they may create new drug resistant bacteria, and whether they may also act as hormone disruptors in humans or the environment.

Biocides in hydraulic fracturing: hazard and vulnerability with respect to potential groundwater pollution

NASA Astrophysics Data System (ADS)

Worrall, Fred; Wilson, Miles; Davies, Richard

2016-04-01

Biocides are one possible chemical additive to frack fluids and their role is to control bacterial growth. Bacterial growth might lead to biofilm build up; and acid sulfide species and hydrogen sulfide (H2S) production: biofilm build up may reduce formation permeability and hinder gas extraction. Kahrilas et al. (2014) published a review of common biocides used in fracking in the USA. The biocides assessed in the review were the sixteen most commonly used in the USA, based on the hydraulic fracturing chemical registry Frac Focus (Frac Focus, 2015). However, the review of Kahrilas et al. (2014) contained no data or observations and so the objective of this study was to consider whether biocides proposed for use in hydrofacturing could be a threat to English groundwater. The study considered all groundwater samples analysed for biocides in English groundwater between 2005 and 2014. The monitoring records were compared to: records of application (both amount and area); and chemical and molecular data for the biocides. The study did not use traditional adsorption and degradation data as these parameters are to prone to variability and are not pure molecular parameters. The study then used the approach of Worrall and Thomsen (2004) to consider the hazard represented by proposed frack biocides and the approach of Worrall and Kolpin (2003) to consider the vulnerability of the areas of potential shale gas exploitation. The study showed that of the 113 biocides tested for in English groundwaters in the decade 2005 - 2014 that 95 were detected above 0.1 g/l . Of these 95, 41 were compounds that were not recorded as being applied during the period of record and the detection of these 41 compounds did not decline over the 10 year period which implies very long residence times and that once compounds do pollute an aquifer then they will be a persistent problem. Furthermore, the solubility of the range of biocides used in frack fluids would imply a potentially higher hazard than for other compounds. For one proposed area of shale gas exploitation we could show that the for the 15 km radius around the proposed frack site the total average probability of detecting a pesticide above 0.1 μg l-1 was 0.08%, while for the same group of pesticides on the national scale, the probability of detection was 0.18%, i.e. for that area the aquifer was less vulnerable to biocide pollution than would be expected.

In situ electrochemical assessment of cytotoxicity of chlorophenols in MCF-7 and HeLa cells.

PubMed

Qin, Hongwei; Liu, Jiguang; Zhang, Zeshi; Li, Jinlian; Gao, Guanggang; Yang, Yuxin; Yuan, Xing; Wu, Dongmei

2014-10-01

An in situ electrochemical method was used to assess the cytotoxicity of chlorophenols using human breast cancer (MCF-7) and cervical carcinoma (HeLa) cells as models. On treatment with different chlorophenols, the electrochemical responses of the selected cells, resulting from the oxidation of guanine and xanthine in the cytoplasm, indicated the cell viability. In addition, the in situ in vitro electrochemical method was further compared with the traditional MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assays. Although similar cytotoxicity data were obtained from both methods, the effective concentrations of chlorophenols that inhibited 50% cell growth (EC50 values) from the electrochemical method were only slightly lower than those from the MTT assay. These results indicate that the in situ in vitro electrochemical method paves a simple, rapid, strongly responsive, and label-free way to the cytotoxicity assessment of different chlorophenol pollutants. Copyright © 2014 Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

van Gestel, C.A.; Ma, W.C.

The acute toxicity of five chlorophenols for two earthworm species was determined in two sandy soils differing in organic matter content and the results were compared with adsorption data. Adsorption increased with increasing organic matter content of the soils, but for tetra- and pentachlorophenol was also influenced by soil pH. Earthworm toxicity was significantly higher in the soil with a low level of organic matter. This difference disappeared when LC50 values were recalculated to concentrations in soil solution using adsorption data. Eisenia fetida andrei showed LC50 values lower than those of Lumbricus rubellus although bioaccumulation was generally higher in themore » latter species. Toxicity and bioaccumulation based on soil solution concentrations increased with increasing lipophilicity of the chlorophenols. The present results indicate that the toxicity and bioaccumulation and therefore the bioavailability of chlorophenols in soil to earthworms are dependent on the concentration in soil solution and can be predicted on the basis of adsorption data. Both the toxicity of and bioaccumulation data on chlorophenols in earthworms demonstrated surprisingly good agreement with those on chlorophenols in fish.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Exon, J.H.

The chlorinated phenols are a group of 19 isomers composed of phenol with substituted chlorines. These chemicals are readily soluble in organic solvents but only slightly soluble in water, except for the chlorophenate salts. Chlorophenols with less than 3 chlorines are not used extensively except in the production of higher chlorophenols and chlorophenyloxyacetic acid herbicides. Pentachlorophenol and some tetrachlorophenols are used worldwide, primarily as wood preservatives or fungicides. Residues of chlorophenols have been found worldwide in soil, water and air samples, in food products, and in human and animal tissues and body fluids. Environmental contamination with these chemicals occurs frommore » industrial effluents, agricultural runoff, breakdown of chlorophenyloxyacetic acid herbicides and hexachlorobenzene, and from spontaneous formation following chlorination of water for disinfection and deodorization. The acute toxicity of these chemicals is relatively low and little is known concerning their chronic effects. Chlorophenols have not been shown conclusively to be mutagens, teratogens or carcinogens. However, these compounds may act as promotors or cocarcinogens and the immune system is particularly sensitive to their toxic effects. Transplacental exposure to chlorophenols may result in embryotoxicity and abortion. The major mode of toxic action is as uncouplers of oxidative phosphorylation. The toxicity of chlorophenols decreases with decreasing chlorination. These chemicals are mild hepatotoxins and are stored mainly in hepatic and renal tissues.« less

A novel anti-influenza copper oxide containing respiratory face mask.

PubMed

Borkow, Gadi; Zhou, Steve S; Page, Tom; Gabbay, Jeffrey

2010-06-25

Protective respiratory face masks protect the nose and mouth of the wearer from vapor drops carrying viruses or other infectious pathogens. However, incorrect use and disposal may actually increase the risk of pathogen transmission, rather than reduce it, especially when masks are used by non-professionals such as the lay public. Copper oxide displays potent antiviral properties. A platform technology has been developed that permanently introduces copper oxide into polymeric materials, conferring them with potent biocidal properties. We demonstrate that impregnation of copper oxide into respiratory protective face masks endows them with potent biocidal properties in addition to their inherent filtration properties. Both control and copper oxide impregnated masks filtered above 99.85% of aerosolized viruses when challenged with 5.66+/-0.51 and 6.17+/-0.37 log(10)TCID(50) of human influenza A virus (H1N1) and avian influenza virus (H9N2), respectively, under simulated breathing conditions (28.3 L/min). Importantly, no infectious human influenza A viral titers were recovered from the copper oxide containing masks within 30 minutes (< or = 0.88 log(10)TCID(50)), while 4.67+/-1.35 log(10)TCID(50) were recovered from the control masks. Similarly, the infectious avian influenza titers recovered from the copper oxide containing masks were < or = 0.97+/-0.01 log(10)TCID(50) and from the control masks 5.03+/-0.54 log(10)TCID(50). The copper oxide containing masks successfully passed Bacterial Filtration Efficacy, Differential Pressure, Latex Particle Challenge, and Resistance to Penetration by Synthetic Blood tests designed to test the filtration properties of face masks in accordance with the European EN 14683:2005 and NIOSH N95 standards. Impregnation of copper oxide into respiratory protective face masks endows them with potent anti-influenza biocidal properties without altering their physical barrier properties. The use of biocidal masks may significantly reduce the risk of hand or environmental contamination, and thereby subsequent infection, due to improper handling and disposal of the masks.

Biocide squirting from an elastomeric tri-layer film.

PubMed

Sonntag, Philippe; Hoerner, Pierre; Cheymol, André; Argy, Gilles; Riess, Gérard; Reiter, Günter

2004-05-01

Protective layers typically act in a passive way by simply separating two sides. Protection is only efficient as long as the layers are intact. If a high level of protection has to be achieved by thin layers, complementary measures need to be in place to ensure safety, even after breakage of the layer-an important issue in medical applications. Here, we present a novel approach for integrating a biocide liquid into a protective film (about 300-500 microm thick), which guarantees that a sufficient amount of biocide is rapidly released when the film is punctured. The film is composed of a middle layer, containing the liquid in droplet-like compartments, sandwiched between two elastomeric boundary layers. When the film is punctured, the liquid squirts out of the middle layer. A theoretical model was used to determine the size and density of droplets that are necessary to ensure a sufficient quantity of biocide is expelled from an adequately elastic matrix to provide protection at the site of damage. We demonstrate the utility of this approach for the fabrication of surgical gloves.

Identification of bacterial contaminants from calcium carbonate filler production lines and an evaluation of biocide based decontamination procedures.

PubMed

Odić, Duško; Prah, Jana; Avguštin, Gorazd

2017-04-01

The aim of this study was to analyze the bacterial community in the production line of a calcium carbonate filler production company and to investigate possible causes for bacterial presence. Throughout 2012, 24 carbonate slurry and six groundwater samples were analyzed. Pseudomonas and Microbacterium were the most frequent contaminants in the slurry, whereas Pseudomonas and Brevundimonas dominated the groundwater samples. Of the 43 different bacterial strains isolated, only five were found both in the slurry and the groundwater, indicating that the latter was not a major source of contamination. The efficacy of 54 commercial biocidal formulations was tested against an artificial bacterial consortium composed of selected slurry isolates. A formulation containing 7.5-15% (v v -1 ) bronopol and 1.0-2.5% (v v -1 ) [chloroisothiazolinone (CIT) + methylisothiazolinone (MIT)] exhibited the highest efficacy. Of the possible causes for bacterial presence, sporogenesis and biocide adsorption to carbonate particles were found to be less probable compared to bacterial adsorption to particles, and the acquisition of resistance to biocides.

Preparation of multifunctional polysaccharide microcontainers for lipophilic bioactive agents.

PubMed

Borodina, Tatiana N; Grigoriev, Dmitry O; Carillo, Maria A; Hartmann, Jürgen; Moehwald, Helmuth; Shchukin, Dmitry G

2014-05-14

Chitosan/xanthan gum microcontainers with a core-shell structure formed due to chemical interactions between polysaccharide chains induced by ultrasonication are presented. Containers were prepared by sonication of water-immiscible (oil-like) liquids in the solution of polysaccharides. One-step fabrication of the container permanent shell is possible, because of the contribution of ultrasonically caused formation of hydrogen bonds and amide linkages. We synthesized containers in a wide size range from 350 nm to 7500 nm, varying in oil/water ratio. The microcontainers were modified with oppositely charged polyelectrolytes and microparticles, which could be used to impart the specified properties to the system. The biocide 4,5-dichloro-2-n-octyl-4-isothiazoline-3-one (DCOIT) was loaded into the proposed containers by utilizing its solution as an oil phase. The following incorporation of the DCOIT containers into the polymer coating demonstrated more sustained antimicrobial activity (∼30%) of the biocide in the encapsulated state, compared to its non-encapsulated form.

Commercial Biocides Induce Transfer of Prophage Φ13 from Human Strains of Staphylococcus aureus to Livestock CC398.

PubMed

Tang, Yuanyue; Nielsen, Lene N; Hvitved, Annemette; Haaber, Jakob K; Wirtz, Christiane; Andersen, Paal S; Larsen, Jesper; Wolz, Christiane; Ingmer, Hanne

2017-01-01

Human strains of Staphylococcus aureus commonly carry the bacteriophage ΦSa3 that encodes immune evasion factors. Recently, this prophage has been found in livestock-associated, methicillin resistant S. aureus (MRSA) CC398 strains where it may promote human colonization. Here, we have addressed if exposure to biocidal products induces phage transfer, and find that during co-culture, Φ13 from strain 8325, belonging to ΦSa3 group, is induced and transferred from a human strain to LA-MRSA CC398 when exposed to sub-lethal concentrations of commercial biocides containing hydrogen peroxide. Integration of ΦSa3 in LA-MRSA CC398 occurs at multiple positions and the integration site influences the stability of the prophage. We did not observe integration in hlb encoding β-hemolysin that contains the preferred ΦSa3 attachment site in human strains, and we demonstrate that this is due to allelic variation in CC398 strains that disrupts the phage attachment site, but not the expression of β-hemolysin. Our results show that hydrogen peroxide present in biocidal products stimulate transfer of ΦSa3 from human to LA-MRSA CC398 strains and that in these strains prophage stability depends on the integration site. Knowledge of ΦSa3 transfer and stability between human and livestock strains may lead to new intervention measures directed at reducing human infection by LA-MRSA strains.

Commercial Biocides Induce Transfer of Prophage Φ13 from Human Strains of Staphylococcus aureus to Livestock CC398

PubMed Central

Tang, Yuanyue; Nielsen, Lene N.; Hvitved, Annemette; Haaber, Jakob K.; Wirtz, Christiane; Andersen, Paal S.; Larsen, Jesper; Wolz, Christiane; Ingmer, Hanne

2017-01-01

Human strains of Staphylococcus aureus commonly carry the bacteriophage ΦSa3 that encodes immune evasion factors. Recently, this prophage has been found in livestock-associated, methicillin resistant S. aureus (MRSA) CC398 strains where it may promote human colonization. Here, we have addressed if exposure to biocidal products induces phage transfer, and find that during co-culture, Φ13 from strain 8325, belonging to ΦSa3 group, is induced and transferred from a human strain to LA-MRSA CC398 when exposed to sub-lethal concentrations of commercial biocides containing hydrogen peroxide. Integration of ΦSa3 in LA-MRSA CC398 occurs at multiple positions and the integration site influences the stability of the prophage. We did not observe integration in hlb encoding β-hemolysin that contains the preferred ΦSa3 attachment site in human strains, and we demonstrate that this is due to allelic variation in CC398 strains that disrupts the phage attachment site, but not the expression of β-hemolysin. Our results show that hydrogen peroxide present in biocidal products stimulate transfer of ΦSa3 from human to LA-MRSA CC398 strains and that in these strains prophage stability depends on the integration site. Knowledge of ΦSa3 transfer and stability between human and livestock strains may lead to new intervention measures directed at reducing human infection by LA-MRSA strains. PMID:29270158

Adaptive Resistance to Biocides in Salmonella enterica and Escherichia coli O157 and Cross-Resistance to Antimicrobial Agents

PubMed Central

Braoudaki, M.; Hilton, A. C.

2004-01-01

The mechanisms by which bacteria resist killing by antibiotics and biocides are still poorly defined, although repeated exposure to sublethal concentrations of antibacterial agents undoubtedly contributes to their development. This study aimed both to investigate the potential of Salmonella enterica and Escherichia coli O157 for adaptive resistance to commonly used biocides and to determine any cross-resistance to antibiotics. Strains were repeatedly passaged in media containing increasing concentrations of a biocide or antibiotic until adaptive resistance was obtained. A wide panel of antimicrobial agents was then screened by using the adapted strain to determine cross-resistance, if any. Adaptive resistance was readily achieved for both S. enterica and E. coli O157. Cross-resistance in adaptively resistant S. enterica varied with the serotype; Salmonella enterica serovar Enteritidis expressed cross-resistance to chloramphenicol, whereas Salmonella enterica serovar Typhimurium expressed cross-resistance to chlorhexidine. Benzalkonium chloride-resistant Salmonella enterica serovar Virchow showed elevated resistance to chlorhexidine; however, chlorhexidine-resistant Salmonella serovar Virchow did not demonstrate reciprocal cross-resistance to benzalkonium chloride, suggesting specific rather than generic resistance mechanisms. E. coli O157 strains acquired high levels of resistance to triclosan after only two sublethal exposures and, when adapted, repeatedly demonstrated decreased susceptibilities to various antimicrobial agents, including chloramphenicol, erythromycin, imipenem, tetracycline, and trimethoprim, as well as to a number of biocides. These observations raise concern over the indiscriminate and often inappropriate use of biocides, especially triclosan, in situations where they are unnecessary, whereby they may contribute to the development of microbial resistance mechanisms. PMID:14715734

Efficiency of four currently used decontamination conditionings in Romania against Aspergillus and Candida strains.

PubMed

Lorin, D; Cristina, R T; Teusdea, V; Mitrănescu, E; Muselin, F; Butnariu, M; David, G; Dumitrescu, E

2017-09-01

Efficacy of four commercial biocidal products (noted A to D), using manufacturers' recommendations, and a contact time of 30minutes, were evaluated in the purpose of standard SR EN1657: 2006 adapted. Were used four strains, two as reference: Aspergillus brasiliensis (niger) (ATCC 16404) and Candida albicans (ATCC 10231), and two isolates: Aspergillus flavus and respectively Aspergillus fumigatus. The inoculum plates containing Malt Extract Agar (MEA) were incubated 48h for C. albicans and 72hours for Aspergillus spp. The standard SR EN1657: 2006 adapted was conducted in two phases: the test cultures preparation and the method validation. Method validation included: the control of experimental conditions and of neutralizant solution, and the method verification. Results revealed that three from the four tested products (A, B and D) had exerted biocidal effect on the studied strains at the recommended concentrations, the registered CFU values being reduced by more than 4 log 10 , conversely in the case of the product (C), applied against A. fumigatus at the recommended concentration of 2%, the biocidal effect was not detected, fact confirmed also by the CFU's value (3.59 log 10 ). The biocide retested at a greater concentration (of 5%), showed a biocidal effect against A. fumigatus after 30minutes, the CFU value being reduced, by more than 5.29 log 10 , evidencing the resistance emergence of A. fumigatus under the repeated pressure of biocides. It is re-confirming that merely the "chemical" defense measures to defuse the fungi's strategies become unproductive. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Toward Tailor-Made Biocide Materials Based on Poly(propylene)/Copper Nanoparticles.

PubMed

Palza, Humberto; Gutiérrez, Sebastian; Delgado, Katherine; Salazar, Oriana; Fuenzalida, Victor; Avila, Jonathan I; Figueroa, Guillermo; Quijada, Raúl

2010-03-16

A set of poly(propylene) composites containing different amounts of copper nanoparticles (CNP) were prepared by the melt mixed method and their antimicrobial behavior was quantitatively studied. The time needed to reduce the bacteria to 50% dropped to half with only 1 v/v % of CNP, compared to the polymer without CNP. After 4 h, this composite killed more than 99.9% of the bacteria. The biocide kinetics can be controlled by the nanofiller content; composites with CNP concentrations higher than 10 v/v % eliminated 99% of the bacteria in less than 2 h. X-ray photoelectron spectroscopy did not detect CNP at the surface, therefore the biocide behavior was attributed to copper in the bulk of the composite. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Silver Ion Biocide Delivery System for Water Disinfection

NASA Technical Reports Server (NTRS)

Slote, Benjamin M.; Salley, Edward; Carr, Daniel; Kimble, Michael C.; Adam, Niklas

2016-01-01

U.S. space exploration missions have long considered returning to the Moon and exploration of Mars that challenge life support systems. For these long duration missions, there is interest in replacing the iodine water treatment system with ionic silver, a proven biocide. For long duration exploration missions, it is imperative that an effective biocide be used that prevents microbial growth, biofilm formation, and microbially induced corrosion in the water storage and distribution systems while minimizing logistical supply requirements associated with the biocide delivery system. Two biocide delivery systems have been developed that electrochemically produce silver ions for disinfecting water throughout the water storage and distribution system. One system uses a newly developed hybrid micro-filtration and ion-exchange membrane to produce an abundance of silver ions at the 1000 ppb level upstream in the water distribution system to prevent biofilm growth. This is followed by a downstream collection module that electrochemically removes these silver ions before the water is discharged. Another approach uses a membraneless reactor to produce a 1000 ppb silver ion concentration level that also has a mechanically driven electrode cleaning mechanism that removes oxide films ensuring long life operation. By maintaining a sufficiently high level of silver ions throughout the water storage and distribution system, biofilm formation is suppressed. This approach overcomes present concerns where spurious silver deposition occurs on the container and flow line surfaces thus lowering the silver ion concentration to unsatisfactory disinfection levels.

Precursor anion states in dissociative electron attachment to chlorophenol isomers.

PubMed

Kossoski, F; Varella, M T do N

2016-07-28

We report a theoretical study on low-energy (<10 eV) elastic electron scattering from chlorophenol isomers, namely, para-chlorophenol (pCP), meta-chlorophenol (mCP), and ortho-chlorophenol (oCP). The calculations were performed with the Schwinger multichannel method with pseudopotentials, and analysis of the computed integral cross sections and virtual orbitals revealed one σCCl (∗), one σOH (∗), and three π(∗) shape resonances. We show that electron capture into the two lower lying π(∗) orbitals initiates dissociative processes that lead to the elimination of the chloride ion, accounting for the two overlapping peaks where this fragment was observed. Despite the relatively small differences on the energetics of the π(∗) resonances, a major isomeric effect was found on their corresponding autodetachment lifetimes, which accounts for the observed increasing cross sections in the progression pCP < mCP < oCP. In particular, dissociation from the π1 (∗) anion of pCP is largely suppressed because of the unfavorable mixing with the σCCl (∗) state. We found the intramolecular hydrogen bond present in oCP to have the opposite effects of stabilizing the σCCl (∗) resonance and destabilizing the σOH (∗) resonance. We also suggest that the hydrogen abstraction observed in chlorophenols and phenol actually takes place by a mechanism in which the incoming electron is directly attached to the dissociative σOH (∗) orbital.

Precursor anion states in dissociative electron attachment to chlorophenol isomers

NASA Astrophysics Data System (ADS)

Kossoski, F.; Varella, M. T. do N.

2016-07-01

We report a theoretical study on low-energy (<10 eV) elastic electron scattering from chlorophenol isomers, namely, para-chlorophenol (pCP), meta-chlorophenol (mCP), and ortho-chlorophenol (oCP). The calculations were performed with the Schwinger multichannel method with pseudopotentials, and analysis of the computed integral cross sections and virtual orbitals revealed one σCCl ∗ , one σOH ∗ , and three π∗ shape resonances. We show that electron capture into the two lower lying π∗ orbitals initiates dissociative processes that lead to the elimination of the chloride ion, accounting for the two overlapping peaks where this fragment was observed. Despite the relatively small differences on the energetics of the π∗ resonances, a major isomeric effect was found on their corresponding autodetachment lifetimes, which accounts for the observed increasing cross sections in the progression pCP < mCP < oCP. In particular, dissociation from the π1 ∗ anion of pCP is largely suppressed because of the unfavorable mixing with the σCCl ∗ state. We found the intramolecular hydrogen bond present in oCP to have the opposite effects of stabilizing the σCCl ∗ resonance and destabilizing the σOH ∗ resonance. We also suggest that the hydrogen abstraction observed in chlorophenols and phenol actually takes place by a mechanism in which the incoming electron is directly attached to the dissociative σOH ∗ orbital.

Biodegradability of Chlorophenols in Surface Waters from the Urban Area of Buenos Aires.

PubMed

Gallego, A; Laurino Soulé, J; Napolitano, H; Rossi, S L; Vescina, C; Korol, S E

2018-04-01

Biodegradability of 2-Chlorophenol (2-CP), 3-Chlorophenol (3-CP), 4-Chlorophenol (4-CP), 2,4-Dichlorophenol (2,4-DCP) and 2,4,6 Trichlorophenol (2,4,6-TCP) has been tested in surface waters in the urban area of Buenos Aires. Samples were taken from the La Plata River and from the Reconquista and Matanza-Riachuelo basins, with a total amount of 18 sampling points. Water quality was established measuring chemical oxygen demand (COD), biochemical oxygen demand (BOD 5 ), and both Escherichia coli and Enterococcus counts. Biodegradability was carried out by a respirometric method, using a concentration of 20 mg L -1 of chlorophenol, and the surface water as inoculum. Chlorophenols concentration in the same water samples were simultaneously measured by a solid phase microextraction (SPME) procedure followed by gas chromatography-mass spectrometry (GC-MS). 2,4-DCP was the most degradable compound followed by 2,4,6-TCP, 4-CP, 3-CP and 2-CP. Biodegradability showed no correlation with compound concentration. At most sampling points the concentration was below the detection limit for all congeners. Biodegradability does not correlate even with COD, BOD 5 , or fecal contamination. Biodegradability assays highlighted information about bacterial exposure to contaminants that parameters routinely used for watercourse characterization do not reveal. For this reason, they might be a helpful tool to complete the characterization of a site.

Palladium Supported on Titanium Carbide: A Highly Efficient, Durable, and Recyclable Bifunctional Catalyst for the Transformation of 4-Chlorophenol and 4-Nitrophenol

PubMed Central

Fan, Guangyin; Li, Xiaojing; Xu, Caili; Jiang, Weidong; Zhang, Yun; Gao, Daojiang; Bi, Jian; Wang, Yi

2018-01-01

Developing highly efficient and recyclable catalysts for the transformation of toxic organic contaminates still remains a challenge. Herein, Titanium Carbide (Ti3C2) MXene modified by alkali treatment process was selected as a support (designated as alk-Ti3C2X2, where X represents the surface terminations) for the synthesis of Pd/alk-Ti3C2X2. Results show that the alkali treatment leads to the increase of surface area and surface oxygen-containing groups of Ti3C2X2, thereby facilitating the dispersion and stabilization of Pd species on the surface of alk-Ti3C2X2. The Pd/alk-Ti3C2X2 catalyst shows excellent catalytic activity for the hydrodechlorination of 4-chlorophenol and the hydrogenation of 4-nitrophenol in aqueous solution at 25 °C and hydrogen balloon pressure. High initial reaction rates of 216.6 and 126.3 min−1·gpd−1 are observed for the hydrodechlorination of 4-chlorophenol and hydrogenation of 4-nitrophenol, respectively. Most importantly, Pd/alk-Ti3C2X2 exhibits excellent stability and recyclability in both reactions without any promoters. The superior property of Pd/alk-Ti3C2X2 makes it as a potential material for practical applications. PMID:29498652

Sorption of chlorophenols from aqueous solution by granular activated carbon, filter coal, pine and hardwood.

PubMed

Hossain, G S M; McLaughlan, R G

2012-09-01

Wood and coal, as low-cost sorbents, have been evaluated as an alternative to commercial granular activated carbon (GAC) for chlorophenol removal. Kinetic experiments indicated that filter coal had a significantly lower rate of uptake (approximately 10% of final uptake was achieved after three hours) than the other sorbents, owing to intra-particle diffusion limitations. The data fitted a pseudo-second-order model. Sorption capacity data showed that GAC had a high sorption capacity (294-467 mg g(-1)) compared with other sorbents (3.2-7.5 mg(g-1)). However, wood and coal had a greater sorption capacity per unit surface area than GAC. Sorption equilibrium data was best predicted using a Freundlich adsorption model. The sorption capacity for all sorbents was 2-chlorophenol < 4-chlorophenol < 2, 4-dichlorophenol, which correlates well with solute hydrophobicity, although the relative differences were much less for coal than the other sorbents. The results showed that pine, hardwood and filter coal can be used as sorbent materials for the removal of chlorophenol from water; however, kinetic considerations may limit the application of filter coal.

Crew Exploration Vehicle (CEV) Potable Water System Verification Description

NASA Technical Reports Server (NTRS)

Peterson, Laurie; DeVera, Jean; Vega, Leticia; Adam, Nik; Steele, John; Gazda, Daniel; Roberts, Michael

2009-01-01

The Crew Exploration Vehicle (CEV), also known as Orion, will ferry a crew of up to six astronauts to the International Space Station (ISS), or a crew of up to four astronauts to the moon. The first launch of CEV is scheduled for approximately 2014. A stored water system on the CEV will supply the crew with potable water for various purposes: drinking and food rehydration, hygiene, medical needs, sublimation, and various contingency situations. The current baseline biocide for the stored water system is ionic silver, similar in composition to the biocide used to maintain quality of the water transferred from the Orbiter to the ISS and stored in Contingency Water Containers (CWCs). In the CEV water system, the ionic silver biocide is expected to be depleted from solution due to ionic silver plating onto the surfaces of the materials within the CEV water system, thus negating its effectiveness as a biocide. Since the biocide depletion is expected to occur within a short amount of time after loading the water into the CEV water tanks at the Kennedy Space Center (KSC), an additional microbial control is a 0.1 micron point of use filter that will be used at the outlet of the Potable Water Dispenser (PWD). Because this may be the first time NASA is considering a stored water system for longterm missions that does not maintain a residual biocide, a team of experts in materials compatibility, biofilms and point of use filters, surface treatment and coatings, and biocides has been created to pinpoint concerns and perform testing to help alleviate those concerns related to the CEV water system. Results from the test plans laid out in the paper presented to SAE last year (Crew Exploration Vehicle (CEV) Potable Water System Verification Coordination, 2008012083) will be detailed in this paper. Additionally, recommendations for the CEV verification will be described for risk mitigation in meeting the physicochemical and microbiological requirements on the CEV PWS.

25 CFR 166.223 - Can I use a permit as collateral for a loan?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Can I use a permit as collateral for a loan? 166.223... PERMITS Permit Requirements Permit (leasehold) Mortgage § 166.223 Can I use a permit as collateral for a loan? We may approve a permit containing a provision that authorizes the permittee to encumber the...

36 CFR 13.116 - Permittee's interest.

Code of Federal Regulations, 2010 CFR

2010-07-01

... NATIONAL PARK SYSTEM UNITS IN ALASKA Cabins General Provisions § 13.116 Permittee's interest. (a) A..., bartered, exchanged, assigned or included as a portion of any sale or exchange of other property by a...

Antibacterial and Antifungal Activity of ZnO Containing Glasses.

PubMed

Esteban-Tejeda, Leticia; Prado, Catuxa; Cabal, Belén; Sanz, Jesús; Torrecillas, Ramón; Moya, José Serafín

2015-01-01

A new family of non-toxic biocides based on low melting point (1250°C) transparent glasses with high content of ZnO (15-40wt%) belonging to the miscibility region of the B2O3-SiO2-Na2O-ZnO system has been developed. These glasses have shown an excellent biocide activity (logarithmic reduction >3) against Gram- (E. coli), Gram+ (S. aureus) and yeast (C. krusei); they are chemically stable in different media (distilled water, sea-like water, LB and DMEN media) as well as biocompatible. The cytotoxicity was evaluated by the Neutral Red Uptake using NIH-3T3 (mouse embryonic fibroblast cells) and the cell viability was >80%. These new glasses can be considered in several and important applications in the field of inorganic non-toxic biocide agents such as medical implants, surgical equipment, protective apparels in hospitals, water purifications systems, food packaging, food storages or textiles.

Antibacterial and Antifungal Activity of ZnO Containing Glasses

PubMed Central

Esteban-Tejeda, Leticia; Prado, Catuxa; Cabal, Belén; Sanz, Jesús; Torrecillas, Ramón; Moya, José Serafín

2015-01-01

A new family of non-toxic biocides based on low melting point (1250°C) transparent glasses with high content of ZnO (15–40wt%) belonging to the miscibility region of the B2O3-SiO2-Na2O-ZnO system has been developed. These glasses have shown an excellent biocide activity (logarithmic reduction >3) against Gram- (E. coli), Gram+ (S. aureus) and yeast (C. krusei); they are chemically stable in different media (distilled water, sea-like water, LB and DMEN media) as well as biocompatible. The cytotoxicity was evaluated by the Neutral Red Uptake using NIH-3T3 (mouse embryonic fibroblast cells) and the cell viability was >80%. These new glasses can be considered in several and important applications in the field of inorganic non-toxic biocide agents such as medical implants, surgical equipment, protective apparels in hospitals, water purifications systems, food packaging, food storages or textiles. PMID:26230940

New promising antifouling agent based on polymeric biocide polyhexamethylene guanidine molybdate.

PubMed

Protasov, Alexander; Bardeau, Jean-Francois; Morozovskaya, Irina; Boretska, Mariia; Cherniavska, Tetiana; Petrus, Lyudmyla; Tarasyuk, Oksana; Metelytsia, Larisa; Kopernyk, Iryna; Kalashnikova, Larisa; Dzhuzha, Oleg; Rogalsky, Sergiy

2017-09-01

A new polymeric biocide polyhexamethylene guanidine (PHMG) molybdate has been synthesized. The obtained cationic polymer has limited water solubility of 0.015 g/100 mL and is insoluble in paint solvents. The results of acute toxicity studies indicate moderate toxicity of PHMG molybdate, which has a median lethal dose at 48 h of 0.7 mg/L for Daphnia magna and at 96 h of 17 mg/L for Danio rerio (zebrafish) freshwater model organisms. Commercial ship paint was then modified by the addition of a low concentration of polymeric biocide 5% (w/w). The painted steel panels were kept in Dnipro River water for the evaluation of the dynamics of fouling biomass. After 129-d exposure, Bryozoa dominated in biofouling of tested substrates, forming 86% (649 g/m 2 ) of the total biomass on control panel surfaces. However, considerably lower Bryozoa fouling biomass (15 g/m 2 ) was detected for coatings containing PHMG molybdate. Dreissenidae mollusks were found to form 88% (2182 g/m 2 ) of the fouling biomass on the control substrates after 228 d of exposure, whereas coatings containing PHMG molybdate showed a much lower biomass value of 23.6 g/m 2 . The leaching rate of PHMG molybdate in water was found to be similar to rates for conventional booster biocides ranging from 5.7 μg/cm 2 /d at the initial stage to 2.2 μg/cm 2 /d at steady state. Environ Toxicol Chem 2017;36:2543-2551. © 2017 SETAC. © 2017 SETAC.

Anaerobic Degradation of Chloroaromatic Compounds in Aquatic Sediments under a Variety of Enrichment Conditions †

PubMed Central

Genthner, Barbara R. Sharak; Price, W. Allen; Pritchard, P. H.

1989-01-01

Anaerobic degradation of monochlorophenols and monochlorobenzoates in a variety of aquatic sediments was compared under four enrichment conditions. A broader range of compounds was degraded in enrichments inoculated with sediment exposed to industrial effluents. Degradation of chloroaromatic compounds was observed most often in methanogenic enrichments and in enrichments amended with 1 mM bromoethane sulfonic acid. Degradation was observed least often in enrichments with added nitrate or sulfate. The presence of 10 mM bromoethane sulfonic acid prevented or inhibited degradation of most compounds tested. Primary enrichments in which KNO3 was periodically replenished to maintain enrichment characteristics degraded chlorobenzoates, but not chlorophenols. In contrast, primary enrichments in which Na2SO4 was periodically replenished failed to degrade any chloroaromatic compounds. Upon transfer to fresh medium, none of the sulfate enrichments required the presence of Na2SO4 for degradation, while only two nitrate enrichments required the presence of KNO3 for degradation. As a class of compounds, chlorophenols were degraded more readily than chlorobenzoates. However, as individual compounds 3-chlorobenzoate, 2-chlorophenol, and 3-chlorophenol degradation was observed most often and with an equal frequency. Within the chlorophenol class, the relative order of degradability was ortho > meta > para, while that of chlorobenzoates was meta > ortho > para, In laboratory transfers, 2-chlorobenzoate, 3-chlorobenzoate, and 2-chlorophenol degradation was most easily maintained, while degradation of para-chlorinated compounds was very difficult to maintain. PMID:16347940

Development of a robust chromatographic method for the detection of chlorophenols in cork oak forest soils.

PubMed

McLellan, Iain; Hursthouse, Andrew; Morrison, Calum; Varela, Adélia; Pereira, Cristina Silva

2014-02-01

A major concern for the cork and wine industry is 'cork taint' which is associated with chloroanisoles, the microbial degradation metabolites of chlorophenols. The use of chlorophenolic compounds as pesticides within cork forests was prohibited in 1993 in the European Union (EU) following the introduction of industry guidance. However, cork produced outside the EU is still thought to be affected and simple, robust methods for chlorophenol analysis are required for wider environmental assessment by industry and local environmental regulators. Soil samples were collected from three common-use forests in Tunisia and from one privately owned forest in Sardinia, providing examples of varied management practice and degree of human intervention. These provided challenge samples for the optimisation of a HPLC-UV detection method. It produced recoveries consistently >75% against a soil CRM (ERM-CC008) for pentachlorophenol. The optimised method, with ultraviolet (diode array) detection is able to separate and quantify 16 different chlorophenols at field concentrations greater than the limits of detection ranging from 6.5 to 191.3 μg/kg (dry weight). Application to a range of field samples demonstrated the absence of widespread contamination in forest soils at sites sampled in Sardinia and Tunisia.

Removal efficiency and toxicity reduction of 4-chlorophenol with physical, chemical and biochemical methods.

PubMed

Gómez, M; Murcia, M D; Dams, R; Christofi, N; Gómez, E; Gómez, J L

2012-01-01

Chlorophenols are well-known priority pollutants and many different treatments have been assessed to facilitate their removal from industrial wastewater. However, an absolute and optimum solution still has to be practically implemented in an industrial setting. In this work, a series ofphysical, chemical and biochemical treatments have been systematically tested for the removal of 4-chlorophenol, and their results have been compared in order to determine the most effective treatment based on removal efficiency and residual by-product formation. Chemical treatments based on advanced oxidation processes (AOP) produced the best results on rate and extent of pollutant removal. The non-chemical technologies showed advantages in terms of complete (in the case of adsorption) or easy (enzymatic treatments) removal of toxic treatment by-products. The AOP methods led to the production of different photoproducts depending on the chosen treatment. Toxic products remained in most cases following treatment, though the toxicity level is significantly reduced with combination treatments. Among the treatments, a photochemical method combining UV, produced with a KrCl excilamp, and hydrogen peroxide achieved total removal of chlorophenol and all by-products and is considered the best treatment for chlorophenol removal.

Magnetic porous carbon as an adsorbent for the enrichment of chlorophenols from water and peach juice samples.

PubMed

Wang, Chun; Ma, Ruiyang; Wu, Qiuhua; Sun, Meng; Wang, Zhi

2014-09-26

In this paper, porous carbon with a highly ordered structure was synthesized using zeolite ZSM-5 as a template and sucrose as a carbon source. Through the in situ reduction of Fe(3+), magnetic property was successfully introduced into the ordered porous carbon, resulting in a magnetic porous carbon (MPC). MPC was used as an adsorbent for the extraction of some chlorophenols (2-chlorophenol, 3-chlorophenol, 2,3-dichlorophenol and 3,4-dichlorophenol) from water and peach juice samples followed by high performance liquid chromatography-ultraviolet detection. Good linearity was observed in the range 1.0-100.0 ng mL(-1) and 2.0-100.0 ng mL(-1) for water and peach juice sample, respectively. The limits of detection (S/N=3) were between 0.10 and 0.30 ng mL(-1). The relative standard deviations were less than 5.3% and the recoveries of the method for the compounds were in the range from 87.8% to 102.3%. The results demonstrated that the MPC had a high adsorptive capability toward the four chlorophenols from water and peach juice samples. Copyright © 2014 Elsevier B.V. All rights reserved.

Quantum chemical and kinetic study of formation of 2-chlorophenoxy radical from 2-chlorophenol: unimolecular decomposition and bimolecular reactions with H, OH, Cl, and O2.

PubMed

Altarawneh, Mohammednoor; Dlugogorski, Bogdan Z; Kennedy, Eric M; Mackie, John C

2008-04-24

This study investigates the kinetic parameters of the formation of the chlorophenoxy radical from the 2-chlorophenol molecule, a key precursor to polychlorinated dibenzo-p-dioxins and dibenzofurans (PCCD/F), in unimolecular and bimolecular reactions in the gas phase. The study develops the reaction potential energy surface for the unimolecular decomposition of 2-chlorophenol. The migration of the phenolic hydrogen to the ortho-C bearing the hydrogen atom produces 2-chlorocyclohexa-2,4-dienone through an activation barrier of 73.6 kcal/mol (0 K). This route holds more importance than the direct fission of Cl or the phenolic H. Reaction rate constants for the bimolecular reactions, 2-chlorophenol + X --> X-H + 2-chlorophenoxy (X = H, OH, Cl, O2) are calculated and compared with the available experimental kinetics for the analogous reactions of X with phenol. OH reaction with 2-chlorophenol produces 2-chlorophenoxy by direct abstraction rather than through addition and subsequent water elimination. The results of the present study will find applications in the construction of detailed kinetic models describing the formation of PCDD/F in the gas phase.

Self-assembly of chlorophenols in water

PubMed Central

Rogalska, Ewa; Rogalski, Marek; Gulik-Krzywicki, Tadeusz; Gulik, Annette; Chipot, Christophe

1999-01-01

In saturated solutions of some di- and trichlorophenols, structures with complex morphologies, consisting of thin, transparent sheets often coiling into helices and ultimately twisting into filaments, were observed under the optical microscope. Freeze-fracture electron microscopy, x-ray diffraction, phase diagrams, and molecular modeling were performed to elucidate the observed phenomena. Here, we present evidence that the chlorophenols studied, when interacting with water, self-assemble into bilayers. The fact that some chlorophenols form the same supramolecular structures as those described previously for structurally nonrelated surfactants sheds light on the mechanisms of self-assembly. PMID:10359753

Micro/nanoreservoirs for controlled release of active species in smart functional coatings =

NASA Astrophysics Data System (ADS)

Maia, Frederico Calheiros

This work reports one possible way to develop new functional coatings used to increase the life time of metallic structures. The functionalities selected and attributed to model coatings in the frame of this work were corrosion protection, self-sensing and prevention of fouling (antifouling). The way used to confer those functionalities to coatings was based on the encapsulation of active compounds (corrosion inhibitors, pH indicators and biocides) in micro and nanocontainers followed by their incorporation into the coating matrices. To confer active corrosion protection, one corrosion inhibitor (2-mercaptobenzothiazole, MBT) was encapsulated in two different containers, firstly in silica nanocapsules (SiNC) and in polyurea microcapsules (PU-MC). The incorporation of both containers in different models coatings shows a significant improvement in the corrosion protection of aluminum alloy 2024 (AA2024). Following the same approach, SiNC and PU-MC were also used for the encapsulation of phenolphthalein (one well known pH indicator) to introduce sensing properties in polymeric coatings. SiNC and PU-MC containing phenolphthalein acted as corrosion sensor, showing a pink coloration due to the beginning of cathodic reaction, resulting in a pH increase identified by those capsules. Their sensing performance was proved in suspension and when integrated in coatings for aluminium alloy 2024 and magnesium alloy AZ31. In a similar way, the biocide activity (antifouling) was assigned to two polymeric matrices using SiNC for encapsulation of one biocide (Dichloro-2-octyl-2H-isothiazol-3-one, DCOIT) and also SiNC-MBT was tested as biocide. The antifouling activity of those two encapsulated compounds was assessed through inhibition and consequent decrease in the bioluminescence of modified E. coli. That effect was verified in suspension and when incorporated in coatings for AISI 1008 carbon steel. The developed micro and nanocontainers presented the desired performance, allowing the introduction of new functionalities to model coatings, showing potential to be used as functional additives in the next generation of multifunctional coatings.

Cattle grazing and fish recovery on US federal lands: can social-ecological systems science help?

Treesearch

Susan Charnley; Hannah Gosnell; Kendra L Wendel; Mary M Rowland; Michael J Wisdom

2018-01-01

In the western US, grazing management on federal lands containing habitat for fish species listed under the US Endangered Species Act (ESA) has sparked social conflict and litigation for decades. To date, the problem has been addressed through a top-down environmental governance system, but rangeland managers and grazing permittees now believe there is a need for more...

New biocide guanidine-containing nanocomposites

NASA Astrophysics Data System (ADS)

Gorbunova, Marina; Lemkina, Larisa

2014-08-01

New water-soluble nanocomposites based on Ag and copolymers of 2,2-diallyl-1,1,3,3-tetraethylguanidiniumchloride with N-vinylpyrrolidone [poly(AGC-VP)] and vinylacetate [poly(AGC-VA)] have been developed. The average silver particle size ranged from 52 to 62 nm for poly(AGC-VA) and from 28 to 30 nm for poly(AGC-VP), with the corresponding UV-vis absorption peak position at 405-410 nm. The using of copolymers resulted in improvement in bactericide properties of composites. Following these results, the newly developed nanocomposite scaffold may be considered for new water-soluble medicines and biocides.

A Novel Anti-Influenza Copper Oxide Containing Respiratory Face Mask

PubMed Central

Borkow, Gadi; Zhou, Steve S.; Page, Tom; Gabbay, Jeffrey

2010-01-01

Background Protective respiratory face masks protect the nose and mouth of the wearer from vapor drops carrying viruses or other infectious pathogens. However, incorrect use and disposal may actually increase the risk of pathogen transmission, rather than reduce it, especially when masks are used by non-professionals such as the lay public. Copper oxide displays potent antiviral properties. A platform technology has been developed that permanently introduces copper oxide into polymeric materials, conferring them with potent biocidal properties. Methodology/Principal Findings We demonstrate that impregnation of copper oxide into respiratory protective face masks endows them with potent biocidal properties in addition to their inherent filtration properties. Both control and copper oxide impregnated masks filtered above 99.85% of aerosolized viruses when challenged with 5.66±0.51 and 6.17±0.37 log10TCID50 of human influenza A virus (H1N1) and avian influenza virus (H9N2), respectively, under simulated breathing conditions (28.3 L/min). Importantly, no infectious human influenza A viral titers were recovered from the copper oxide containing masks within 30 minutes (≤0.88 log10TCID50), while 4.67±1.35 log10TCID50 were recovered from the control masks. Similarly, the infectious avian influenza titers recovered from the copper oxide containing masks were ≤0.97±0.01 log10TCID50 and from the control masks 5.03±0.54 log10TCID50. The copper oxide containing masks successfully passed Bacterial Filtration Efficacy, Differential Pressure, Latex Particle Challenge, and Resistance to Penetration by Synthetic Blood tests designed to test the filtration properties of face masks in accordance with the European EN 14683:2005 and NIOSH N95 standards. Conclusions/Significance Impregnation of copper oxide into respiratory protective face masks endows them with potent anti-influenza biocidal properties without altering their physical barrier properties. The use of biocidal masks may significantly reduce the risk of hand or environmental contamination, and thereby subsequent infection, due to improper handling and disposal of the masks. PMID:20592763

RELATIVE POTENCY RANKING FOR CHLOROPHENOLS

EPA Science Inventory

Recently the National Center for Environmental Assessment-Cincinnati completed a feasibility study for developing a toxicity related relative potency ranking scheme for chlorophenols. In this study it was concluded that a large data base exists pertaining to the relative toxicity...

Fluorescent Sensing of Chlorophenols in Water Using an Azo Dye Modified β-Cyclodextrin Polymer

PubMed Central

Ncube, Phendukani; Krause, Rui W.; Mamba, Bhekie B.

2011-01-01

A water soluble azo dye modified β-cyclodextrin polymer 4 was synthesized and used as a chemosensor for the detection of chlorinated phenols, model chlorinated by-products (CBPs) of water treatment for drinking purposes. The characterization of the intermediates and the azo dye modified β-CD polymer was done by UV/Vis Spectrophotometry, FT-IR and 1H-NMR spectroscopies. The chlorophenols were capable of quenching the fluorescence of the polymer. The polymer showed greater sensitivity towards 2,4-dichlorophenol, with a sensitivity factor of 0.35 compared to 0.05 and 0.12 for phenol and 4-chlorophenol, respectively. The stability constants (Ks) of the pollutants were also determined by the Benesi-Hildebrand method to be 2.104 × 103 M−1 for 2,4-dichlorophenol and 1.120 × 102 M−1 for 4-chlorophenol. PMID:22163864

Adsorption of phenolic compound by aged-refuse.

PubMed

Xiaoli, Chai; Youcai, Zhao

2006-09-01

The adsorption of phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol by aged-refuse has been studied. Adsorption isotherms have been determined for phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol and the data fits well to the Freundlich equation. The chlorinated phenols are absorbed more strongly than the phenol and the adsorption capacity has an oblivious relationship with the numbers and the position of chlorine subsistent. The experiment data suggests that both the partition function and the chemical adsorption involve in the adsorption process. Pseudo-first-order and pseudo-second-order model were applied to investigate the kinetics of the adsorption and the results show that it fit the pseudo-second-order model. More than one step involves in the adsorption process and the overall rate of the adsorption process appears to be controlled by the chemical reaction. The thermodynamic analysis indicates that the adsorption is spontaneous and endothermic.

Comparison of Natural and Engineered Chlorophenol Bioremediation Enzymes

DTIC Science & Technology

2015-02-26

herein addresses the urgent need to incorporate biological strategies into environmental restoration efforts ( bioremediation ) that focus on the catalytic... Bioremediation Enzymes The views, opinions and/or findings contained in this report are those of the author(s) and should not contrued as an official Department...Army Research Office P.O. Box 12211 Research Triangle Park, NC 27709-2211 dehaloperoxidase, bioremediation , halophenol, Amphitrite ornata, marine

15 CFR 971.801 - Records to be maintained and information to be submitted by licensees and permittees.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., DEPARTMENT OF COMMERCE GENERAL REGULATIONS OF THE ENVIRONMENTAL DATA SERVICE DEEP SEABED MINING REGULATIONS... applicant, licensee or permittee will be required to submit to the Administrator, upon request, data or...

15 CFR 971.801 - Records to be maintained and information to be submitted by licensees and permittees.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., DEPARTMENT OF COMMERCE GENERAL REGULATIONS OF THE ENVIRONMENTAL DATA SERVICE DEEP SEABED MINING REGULATIONS... applicant, licensee or permittee will be required to submit to the Administrator, upon request, data or...

15 CFR 971.801 - Records to be maintained and information to be submitted by licensees and permittees.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., DEPARTMENT OF COMMERCE GENERAL REGULATIONS OF THE ENVIRONMENTAL DATA SERVICE DEEP SEABED MINING REGULATIONS... applicant, licensee or permittee will be required to submit to the Administrator, upon request, data or...

15 CFR 971.801 - Records to be maintained and information to be submitted by licensees and permittees.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., DEPARTMENT OF COMMERCE GENERAL REGULATIONS OF THE ENVIRONMENTAL DATA SERVICE DEEP SEABED MINING REGULATIONS... applicant, licensee or permittee will be required to submit to the Administrator, upon request, data or...

15 CFR 971.801 - Records to be maintained and information to be submitted by licensees and permittees.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., DEPARTMENT OF COMMERCE GENERAL REGULATIONS OF THE ENVIRONMENTAL DATA SERVICE DEEP SEABED MINING REGULATIONS... applicant, licensee or permittee will be required to submit to the Administrator, upon request, data or...

Resistance to Antibiotics, Biocides, Preservatives and Metals in Bacteria Isolated from Seafoods: Co-Selection of Strains Resistant or Tolerant to Different Classes of Compounds

PubMed Central

Romero, José L.; Grande Burgos, María J.; Pérez-Pulido, Rubén; Gálvez, Antonio; Lucas, Rosario

2017-01-01

Multi-drug resistant bacteria (particularly those producing extended-spectrum β-lactamases) have become a major health concern. The continued exposure to antibiotics, biocides, chemical preservatives, and metals in different settings such as the food chain or in the environment may result in development of multiple resistance or co-resistance. The aim of the present study was to determine multiple resistances (biocides, antibiotics, chemical preservatives, phenolic compounds, and metals) in bacterial isolates from seafoods. A 75.86% of the 87 isolates studied were resistant to at least one antibiotic or one biocide, and 6.90% were multiply resistant to at least three biocides and at least three antibiotics. Significant (P < 0.05) moderate or strong positive correlations were detected between tolerances to biocides, between antibiotics, and between antibiotics with biocides and other antimicrobials. A sub-set of 30 isolates selected according to antimicrobial resistance profile and food type were identified by 16S rDNA sequencing and tested for copper and zinc tolerance. Then, the genetic determinants for biocide and metal tolerance and antibiotic resistance were investigated. The selected isolates were identified as Pseudomonas (63.33%), Acinetobacter (13.33%), Aeromonas (13.33%), Shewanella, Proteus and Listeria (one isolate each). Antibiotic resistance determinants detected included sul1 (43.33% of tested isolates), sul2 (6.66%), blaTEM (16.66%), blaCTX−M (16.66%), blaPSE (10.00%), blaIMP (3.33%), blaNDM−1 (3.33%), floR (16.66%), aadA1 (20.0%), and aac(6′)-Ib (16.66%). The only biocide resistance determinant detected among the selected isolates was qacEΔ1 (10.00%). A 23.30 of the selected isolates were able to grow on media containing 32 mM copper sulfate, and 46.60% on 8 mM zinc chloride. The metal resistance genes pcoA/copA, pcoR, and chrB were detected in 36.66, 6.66, and 13.33% of selected isolates, respectively. Twelve isolates tested positive for both metal and antibiotic resistance genes, including one isolate positive for the carbapenemase gene blaNDM−1 and for pcoA/copA. These results suggest that exposure to metals could co-select for antibiotic resistance and also highlight the potential of bacteria on seafoods to be involved in the transmission of antimicrobial resistance genes. PMID:28912764

Layer of organic pine forest soil on top of chlorophenol-contaminated mineral soil enhances contaminant degradation.

PubMed

Sinkkonen, Aki; Kauppi, Sari; Simpanen, Suvi; Rantalainen, Anna-Lea; Strömmer, Rauni; Romantschuk, Martin

2013-03-01

Chlorophenols, like many other synthetic compounds, are persistent problem in industrial areas. These compounds are easily degraded in certain natural environments where the top soil is organic. Some studies suggest that mineral soil contaminated with organic compounds is rapidly remediated if it is mixed with organic soil. We hypothesized that organic soil with a high degradation capacity even on top of the contaminated mineral soil enhances degradation of recalcitrant chlorophenols in the mineral soil below. We first compared chlorophenol degradation in different soils by spiking pristine and pentachlorophenol-contaminated soils with 2,4,6-trichlorophenol in 10-L buckets. In other experiments, we covered contaminated mineral soil with organic pine forest soil. We also monitored in situ degradation on an old sawmill site where mineral soil was either left intact or covered with organic pine forest soil. 2,4,6-Trichlorophenol was rapidly degraded in organic pine forest soil, but the degradation was slower in other soils. If a thin layer of the pine forest humus was added on top of mineral sawmill soil, the original chlorophenol concentrations (high, ca. 70 μg g(-1), or moderate, ca. 20 μg g(-1)) in sawmill soil decreased by >40 % in 24 days. No degradation was noticed if the mineral soil was kept bare or if the covering humus soil layer was sterilized beforehand. Our results suggest that covering mineral soil with an organic soil layer is an efficient way to remediate recalcitrant chlorophenol contamination in mineral soils. The results of the field experiment are promising.

2-Chlorophenol

Integrated Risk Information System (IRIS)

2 - Chlorophenol ; CASRN 95 - 57 - 8 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic E

25 CFR 166.310 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2010 CFR

2010-04-01

... LAND AND WATER GRAZING PERMITS Land and Operations Management § 166.310 What must a permittee do to...; and (c) Restrict the movement of exposed or infected livestock. Management Plans and Environmental...

Adaptation of amoebae to cooling tower biocides.

PubMed

Srikanth, S; Berk, S G

1994-05-01

Adaptation of amoebae to four cooling tower Biocides, which included a thiocarbamate compound, tributyltin neodecanoate mixed with quaternary ammonium compounds (TBT/QAC), another QAC alone, and an isothiazolin derivative, was studied. Previously we found that amoebae isolated from waters of cooling towers were more resistant to cooling tower biocides than amoebae from other habitats. Acanthamoeba hatchetti and Cochliopodium bilimbosum, obtained from American Type Culture Collection and used in the previous studies, were tested to determine whether they could adapt to cooling tower Biocides. A. hatchetti was preexposed to subinhibitory concentrations of the four Biocides for 72h, after which they were tested for their resistance to the same and other biocides. C. bilimbosum was exposed to only two biocides, as exposure to the other two was lethal after 72 h. Preexposure to the subinhibitory concentrations of the Biocides increased the resistance of the amoebae, as indicated by a significant increase in the minimum inhibitory concentration (up to 30-fold). In addition, cross-resistance was also observed, i.e., exposure to one biocide caused resistance to other biocides. These results show that amoebae can adapt to biocides in a short time. The phenomenon of cross-resistance indicates that regularly alternating biocides, as is done to control microbial growth in cooling towers, may not be effective in keeping amoeba populations in check. On the contrary, exposure to one biocide may boost the amoebae's resistance to a second biocide before the second biocide is used in the cooling tower. Since amoebae may harbor Legionella, or alone cause human diseases, these results may be important in designing effective strategies for controlling pathogens in cooling towers.

Fabrication of a novel hydrophobic/ion-exchange mixed-mode adsorbent for the dispersive solid-phase extraction of chlorophenols from environmental water samples.

PubMed

Gao, Li; Wei, Yinmao

2016-08-01

A novel mixed-mode adsorbent was prepared by functionalizing silica with tris(2-aminoethyl)amine and 3-phenoxybenzaldehyde as the main mixed-mode scaffold due to the presence of the plentiful amino groups and benzene rings in their molecules. The adsorption mechanism was probed with acidic, natural and basic compounds, and the mixed hydrophobic and ion-exchange interactions were found to be responsible for the adsorption of analytes. The suitability of dispersive solid-phase extraction was demonstrated in the determination of chlorophenols in environmental water. Several parameters, including sample pH, desorption solvent, ionic strength, adsorbent dose, and extraction time were optimized. Under the optimal extraction conditions, the proposed dispersive solid-phase extraction coupled with high-performance liquid chromatography showed good linearity range and acceptable limits of detection (0.22∽0.54 ng/mL) for five chlorophenols. Notably, the higher extraction recoveries (88.7∽109.7%) for five chlorophenols were obtained with smaller adsorbent dose (10 mg) and shorter extraction time (15 min) compared with the reported methods. The proposed method might be potentially applied in the determination of trace chlorophenols in real water samples. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Biocidal Inactivation of Lactococcus lactis Bacteriophages: Efficacy and Targets of Commonly Used Sanitizers

PubMed Central

Hayes, Stephen; Murphy, James; Mahony, Jennifer; Lugli, Gabriele A.; Ventura, Marco; Noben, Jean-Paul; Franz, Charles M. A. P.; Neve, Horst; Nauta, Arjen; Van Sinderen, Douwe

2017-01-01

Lactococcus lactis strains, being intensely used in the dairy industry, are particularly vulnerable to members of the so-called 936 group of phages. Sanitization and disinfection using purpose-made biocidal solutions is a critical step in controlling phage contamination in such dairy processing plants. The susceptibility of 36 936 group phages to biocidal treatments was examined using 14 biocides and commercially available sanitizers. The targets of a number of these biocides were investigated by means of electron microscopic and proteomic analyses. The results from this study highlight significant variations in phage resistance to biocides among 936 phages. Furthermore, rather than possessing resistance to specific biocides or biocide types, biocide-resistant phages tend to possess a broad tolerance to multiple classes of antimicrobial compounds. PMID:28210242

Biocides in urban wastewater treatment plant influent at dry and wet weather: concentrations, mass flows and possible sources.

PubMed

Bollmann, Ulla E; Tang, Camilla; Eriksson, Eva; Jönsson, Karin; Vollertsen, Jes; Bester, Kai

2014-09-01

In recent years, exterior thermal insulation systems became more and more important leading to an increasing amount of houses equipped with biocide-containing organic façade coatings or fungicide treated wood. It is known that these biocides, e.g. terbutryn, carbendazim, and diuron, as well as wood preservatives as propiconazole, leach out of the material through contact with wind driven rain. Hence, they are present in combined sewage during rain events in concentrations up to several hundred ng L(-1). The present study focused on the occurrence of these biocides in five wastewater treatment plants in Denmark and Sweden during dry and wet weather. It was discovered, that biocides are detectable not only during wet weather but also during dry weather when leaching from façade coatings can be excluded as source. In most cases, the concentrations during dry weather were in the same range as during wet weather (up to 100 ng L(-1)); however, for propiconazole noteworthy high concentrations were detected in one catchment (4.5 μg L(-1)). Time resolved sampling (12 × 2 h) enabled assessments about possible sources. The highest mass loads during wet weather were detected when the rain was heaviest (e.g. up to 116 mg h(-1) carbendazim or 73 mg h(-1) mecoprop) supporting the hypothesis that the biocides were washed off by wind driven rain. Contrary, the biocide emissions during dry weather were rather related to household activities than with emissions from buildings, i.e., emissions were highest during morning and evening hours (up to 50 mg h(-1)). Emissions during night were significantly lower than during daytime. Only for propiconazole a different emission behaviour during dry weather was observed: the mass load peaked in the late afternoon (3 g h(-1)) and declined slowly afterwards. Most likely this emission was caused by a point source, possibly from inappropriate cleaning of spray equipment for agriculture or gardening. Copyright © 2014 Elsevier Ltd. All rights reserved.

77 FR 10524 - Information Collections Being Reviewed by the Federal Communications Commission Under Delegated...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-22

... or Permittee, or Assignment of License or Permit, for an FM or TV Translator Station, or a Low Power... permittee for an FM or TV translator station, or low power TV station. This collection also includes the...

Effects of materials surface preparation for use in spacecraft potable water storage tanks

NASA Astrophysics Data System (ADS)

Wallace, William T.; Wallace, Sarah L.; Loh, Leslie J.; Kuo, C. K. Mike; Hudson, Edgar K.; Marlar, Tyler J.; Gazda, Daniel B.

2017-12-01

Maintaining a safe supply of potable water is of utmost importance when preparing for long-duration spaceflight missions, with the minimization of microbial growth being one major aspect. While biocides, such as ionic silver, historically have been used for microbial control in spaceflight, their effectiveness is sometimes limited due to surface reactions with the materials of the storage containers that reduce their concentrations below the effective range. For the Multi-Purpose Crew Vehicle, the primary wetted materials of the water storage system are stainless steel and a titanium alloy, and ionic silver has been chosen to serve as the biocide. As an attempt to understand what processes might reduce the known losses of silver, different treatment processes were attempted and samples of the wetted materials were tested, individually and together, to determine the relative loss of biocide under representative surface area-to-volume ratios. The results of testing presented here showed that the materials could be treated by a nitric acid rinse or a high-concentration silver spike to reduce the loss of silver and bacterial growth. It was also found that the minimum biocidal concentration could be maintained for over 28 days. These results have pointed to approaches that could be used to successfully maintain silver in spacecraft water systems for long-duration missions.

DIOXIN AND FURAN FORMATION ON FLY ASH FROM A MIXTURE OF CHLOROPHENOLS

EPA Science Inventory

To establish the relationship between specific chlorophenol (CP) congener distributions and polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/F) products this work investigated the formation of PCDDs/Fs from different CP mixtures passed over fly ash under selected reaction ...

DECHLORINATION ACTIVITY (CROSS-ACCLIMATION) OF FRESHWATER SEDIMENTS ADAPTED TO MONO- AND DI-CHLOROPHENOLS

EPA Science Inventory

The reductive dechlorination of chlorophenols (CPs) in sediment slurries (10% solids) adapted to dechlorinate mono- and di-CPs (DCP) was investigated to define the regiospecificity of the dechlorination reaction. nadapted sediment slurries amended with various ortho-substituted C...

Phenotypic changes contributing to Enterobacter gergoviae biocide resistance.

PubMed

Périamé, M; Philippe, N; Condell, O; Fanning, S; Pagès, J-M; Davin-Regli, A

2015-08-01

Enterobacter gergoviae is a recurrent contaminant of cosmetic and hygiene products. To understand how this bacterium adapts to biocides, we studied Ent. gergoviae CIP 76.01 and its triclosan and Methylisothiazolinone-chloromethylisothiazolinone (MIT-CMIT) tolerant isogenic mutants. They were compared with others also isolated from contaminated cosmetics. Phenotypic differences were noted and these included changes in the bacterial envelope and flagella along with differences in motility, and biofilm growth rates. Triclosan and MIT-CMIT derivatives expressed flagella and other MIT-CMIT derivatives exhibited some external appendages. Those bacteria expressing a high-level minimal inhibitory concentration to MIT-CMIT, expressed a strong biofilm formation. No differential phenotypes were noted for carbon source utilisation. Enterobacter gergoviae demonstrated a diverse response to both of these preservatives contained in cosmetic preparations, depending on their concentrations. Interestingly, this adaptive response is associated with modifications of filament structure-related proteins contributing to increase the organism motility and the production of biofilm. Recurrent contaminations of cosmetics products by Ent. gergoviae, needed a better understanding concerning the bacterial adaptation to preservative agents, with particular concern to triclosan and MIT-CMIT. We demonstrated that bacteria response is associated to various mechanisms represented by expression of external appendages (pili or fimbriae) that control cell motility and biofilm formation and evolving as the concentration of biocides adaptation increased. Such mechanisms which are not chemical specific can also promote a cross-resistance to other biocidal agents. The characterization of Ent. gergoviae adaptability to biocides allows industry to adjust the ranges of concentrations and composition of preservatives in formula. © 2015 The Society for Applied Microbiology.

Zebrafish Functional Genetics Approach to the Pathogenesis of Well-Differentiated Liposarcoma

DTIC Science & Technology

2015-12-01

humans, and predis- posing factors include exposure to dioxin-containing herbicidal agents used during the Vietnam War (Agent Orange) and radiation...Acad Sci U S A (2011);108:16386-91. PMCID: 3182699 Institute of Medicine (1994). Veterans and Agent Orange: Health Effects of Herbicides Used in...to phenoxy herbicides , chlorophenols, and dioxins. An expanded and updated international cohort study." Am J Epidemiol (1997);145:1061-75. PMCID

40 CFR 172.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... grants permission to a permittee or a permittee's designated participant for the use of an experimental use pesticide at an application site owned or controlled by the cooperator. Experimental animals means... supervising the use or evaluation of, an experimental use pesticide to be applied at a specific application...

Development of antimicrobial active packaging materials based on gluten proteins.

PubMed

Gómez-Heincke, Diana; Martínez, Inmaculada; Partal, Pedro; Guerrero, Antonio; Gallegos, Críspulo

2016-08-01

The incorporation of natural biocide agents into protein-based bioplastics, a source of biodegradable polymeric materials, manufactured by a thermo-mechanical method is a way to contribute to a sustainable food packaging industry. This study assesses the antimicrobial activity of 10 different biocides incorporated into wheat gluten-based bioplastics. The effect that formulation, processing, and further thermal treatments exert on the thermo-mechanical properties, water absorption characteristics and rheological behaviour of these materials is also studied. Bioplastics containing six of the 10 examined bioactive agents have demonstrated suitable antimicrobial activity at 37 °C after their incorporation into the bioplastic. Moreover, the essential oils are able to create an antimicrobial atmosphere within a Petri dish. Depending on the selected biocide, its addition may alter the bioplastics protein network in a different extent, which leads to materials exhibiting less water uptake and different rheological and thermo-mechanical behaviours. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

EFFECTS OF TRANSPLACENTAL EXPOSURE TO CHLORINATED PHENOLS

EPA Science Inventory

Female rats were exposed to 0,5,50 or 500 ppm of 2-Chlorophenol (2CP) or pentachlorophenol (PCP). The study was designed to produce progeny which were exposed to the chlorophenolic compounds both prenatally and postnatally. Percent conception, litter size, birth weight, and numbe...

Cancer incidence following chlorophenol exposure in a community in southern Finland.

PubMed

Lampi, P; Hakulinen, T; Luostarinen, T; Pukkala, E; Teppo, L

1992-01-01

Chlorophenols have contaminated the drinking water system and the local lake in the village of Järvelä in southern Finland. Local geology, ground water streams, and chemical analyses incriminated a local sawmill as the only plausible source of exposure. Cancer incidence in the municipality of Kärkölä (half of the population lives in Järvelä), compared with the rest of the local health-care district and with the greater cancer control region, indicated an excess of soft-tissue sarcomas and non-Hodgkin's lymphomas. A case-control study, which focused on cancers of the colon, bladder and soft tissues, lymphomas, and leukemia, demonstrated a significantly elevated risk ratio for non-Hodgkin's lymphomas among persons who consumed fish from the local lake, which was contaminated with chlorophenols. Probable exposure to chlorophenol-contaminated drinking water played a role in the increased incidence of non-Hodgkin's lymphomas and possibly was a factor in the development of soft-tissue sarcoma.

14 CFR 437.69 - Communications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Communications. 437.69 Section 437.69... TRANSPORTATION LICENSING EXPERIMENTAL PERMITS Safety Requirements § 437.69 Communications. (a) A permittee must be in communication with Air Traffic Control during all phases of flight. (b) A permittee must record...

14 CFR 437.69 - Communications.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Communications. 437.69 Section 437.69... TRANSPORTATION LICENSING EXPERIMENTAL PERMITS Safety Requirements § 437.69 Communications. (a) A permittee must be in communication with Air Traffic Control during all phases of flight. (b) A permittee must record...

14 CFR 437.69 - Communications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Communications. 437.69 Section 437.69... TRANSPORTATION LICENSING EXPERIMENTAL PERMITS Safety Requirements § 437.69 Communications. (a) A permittee must be in communication with Air Traffic Control during all phases of flight. (b) A permittee must record...

Case-control study: soft-tissue sarcomas and exposure to phenoxyacetic acids or chlorophenols.

PubMed Central

Hardell, L.; Sandström, A.

1979-01-01

In 1977 a number of patients with soft-tissue sarcomas and previous exposure to phenoxyacetic acids were described. Following from these observations a matched case-control study was made. Exposure to chlorophenols was also included in this study. The results showed that exposure to phenoxyacetic acids or chlorophenols gave an approximately 6-fold increase in the risk for this type of tumour. It was not possible to determine, however, whether the carcinogenic effect was exerted by these compounds or by impurities such as chlorinated dibenzodioxins and dibenzofurans that in almost all cases were part of the commercial preparations. PMID:444410

Efficacy of Biocides Used in the Modern Food Industry To Control Salmonella enterica, and Links between Biocide Tolerance and Resistance to Clinically Relevant Antimicrobial Compounds

PubMed Central

Condell, Orla; Iversen, Carol; Cooney, Shane; Power, Karen A.; Walsh, Ciara; Burgess, Catherine

2012-01-01

Biocides play an essential role in limiting the spread of infectious disease. The food industry is dependent on these agents, and their increasing use is a matter for concern. Specifically, the emergence of bacteria demonstrating increased tolerance to biocides, coupled with the potential for the development of a phenotype of cross-resistance to clinically important antimicrobial compounds, needs to be assessed. In this study, we investigated the tolerance of a collection of susceptible and multidrug-resistant (MDR) Salmonella enterica strains to a panel of seven commercially available food-grade biocide formulations. We explored their abilities to adapt to these formulations and their active biocidal agents, i.e., triclosan, chlorhexidine, hydrogen peroxide, and benzalkonium chloride, after sequential rounds of in vitro selection. Finally, cross-tolerance of different categories of biocidal formulations, their active agents, and the potential for coselection of resistance to clinically important antibiotics were investigated. Six of seven food-grade biocide formulations were bactericidal at their recommended working concentrations. All showed a reduced activity against both surface-dried and biofilm cultures. A stable phenotype of tolerance to biocide formulations could not be selected. Upon exposure of Salmonella strains to an active biocidal compound, a high-level of tolerance was selected for a number of Salmonella serotypes. No cross-tolerance to the different biocidal agents or food-grade biocide formulations was observed. Most tolerant isolates displayed changes in their patterns of susceptibility to antimicrobial compounds. Food industry biocides are effective against planktonic Salmonella. When exposed to sublethal concentrations of individual active biocidal agents, tolerant isolates may emerge. This emergence was associated with changes in antimicrobial susceptibilities. PMID:22367085

Efficacy of biocides used in the modern food industry to control salmonella enterica, and links between biocide tolerance and resistance to clinically relevant antimicrobial compounds.

PubMed

Condell, Orla; Iversen, Carol; Cooney, Shane; Power, Karen A; Walsh, Ciara; Burgess, Catherine; Fanning, Séamus

2012-05-01

Biocides play an essential role in limiting the spread of infectious disease. The food industry is dependent on these agents, and their increasing use is a matter for concern. Specifically, the emergence of bacteria demonstrating increased tolerance to biocides, coupled with the potential for the development of a phenotype of cross-resistance to clinically important antimicrobial compounds, needs to be assessed. In this study, we investigated the tolerance of a collection of susceptible and multidrug-resistant (MDR) Salmonella enterica strains to a panel of seven commercially available food-grade biocide formulations. We explored their abilities to adapt to these formulations and their active biocidal agents, i.e., triclosan, chlorhexidine, hydrogen peroxide, and benzalkonium chloride, after sequential rounds of in vitro selection. Finally, cross-tolerance of different categories of biocidal formulations, their active agents, and the potential for coselection of resistance to clinically important antibiotics were investigated. Six of seven food-grade biocide formulations were bactericidal at their recommended working concentrations. All showed a reduced activity against both surface-dried and biofilm cultures. A stable phenotype of tolerance to biocide formulations could not be selected. Upon exposure of Salmonella strains to an active biocidal compound, a high-level of tolerance was selected for a number of Salmonella serotypes. No cross-tolerance to the different biocidal agents or food-grade biocide formulations was observed. Most tolerant isolates displayed changes in their patterns of susceptibility to antimicrobial compounds. Food industry biocides are effective against planktonic Salmonella. When exposed to sublethal concentrations of individual active biocidal agents, tolerant isolates may emerge. This emergence was associated with changes in antimicrobial susceptibilities.

47 CFR 1.526 - Records to be maintained locally for public inspection by commercial applicants, permittees and...

Code of Federal Regulations, 2010 CFR

2010-10-01

... inspection by commercial applicants, permittees and licensees. 1.526 Section 1.526 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL PRACTICE AND PROCEDURE Broadcast Applications and Proceedings General Filing Requirements § 1.526 Records to be maintained locally for public inspection by commercial applicants...

14 CFR 437.93 - Compliance monitoring.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Compliance monitoring. 437.93 Section 437....93 Compliance monitoring. A permittee must allow access by, and cooperate with, federal officers or employees or other individuals authorized by the FAA to observe any activities of the permittee, or of its...

14 CFR 437.93 - Compliance monitoring.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Compliance monitoring. 437.93 Section 437....93 Compliance monitoring. A permittee must allow access by, and cooperate with, federal officers or employees or other individuals authorized by the FAA to observe any activities of the permittee, or of its...

14 CFR 437.93 - Compliance monitoring.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Compliance monitoring. 437.93 Section 437....93 Compliance monitoring. A permittee must allow access by, and cooperate with, federal officers or employees or other individuals authorized by the FAA to observe any activities of the permittee, or of its...

14 CFR 437.93 - Compliance monitoring.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Compliance monitoring. 437.93 Section 437....93 Compliance monitoring. A permittee must allow access by, and cooperate with, federal officers or employees or other individuals authorized by the FAA to observe any activities of the permittee, or of its...

14 CFR 437.93 - Compliance monitoring.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Compliance monitoring. 437.93 Section 437....93 Compliance monitoring. A permittee must allow access by, and cooperate with, federal officers or employees or other individuals authorized by the FAA to observe any activities of the permittee, or of its...

30 CFR 774.12 - Post-permit issuance information requirements for permittees.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for permittees. 774.12 Section 774.12 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL... competent jurisdiction grants a stay of the cessation order and the stay remains in effect. (c) Within 60...

27 CFR 555.56 - Change in trade name.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Change in trade name. 555... trade name. A licensee or permittee continuing to conduct business or operations at the location shown... in trade name under which he conducts his business or operations. However, the licensee or permittee...

27 CFR 555.56 - Change in trade name.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Change in trade name. 555... trade name. A licensee or permittee continuing to conduct business or operations at the location shown... in trade name under which he conducts his business or operations. However, the licensee or permittee...

27 CFR 555.56 - Change in trade name.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Change in trade name. 555... trade name. A licensee or permittee continuing to conduct business or operations at the location shown... in trade name under which he conducts his business or operations. However, the licensee or permittee...

27 CFR 555.56 - Change in trade name.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Change in trade name. 555... trade name. A licensee or permittee continuing to conduct business or operations at the location shown... in trade name under which he conducts his business or operations. However, the licensee or permittee...

7 CFR 319.55-5 - Notice of arrival by permittee.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Notice of arrival by permittee. 319.55-5 Section 319.55-5 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FOREIGN QUARANTINE NOTICES Rice Rules and Regulations § 319.55...

7 CFR 319.55-5 - Notice of arrival by permittee.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Notice of arrival by permittee. 319.55-5 Section 319.55-5 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FOREIGN QUARANTINE NOTICES Rice Rules and Regulations § 319.55...

7 CFR 319.41-4 - Notice of arrival by permittee.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Notice of arrival by permittee. 319.41-4 Section 319.41-4 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FOREIGN QUARANTINE NOTICES Indian Corn or Maize, Broomcorn, and...

25 CFR 173.11 - Supervision of permittees' rates.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true Supervision of permittees' rates. 173.11 Section 173.11 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER CONCESSIONS, PERMITS AND LEASES ON LANDS WITHDRAWN OR ACQUIRED IN CONNECTION WITH INDIAN IRRIGATION PROJECTS § 173.11 Supervision...

25 CFR 173.11 - Supervision of permittees' rates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Supervision of permittees' rates. 173.11 Section 173.11 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER CONCESSIONS, PERMITS AND LEASES ON LANDS WITHDRAWN OR ACQUIRED IN CONNECTION WITH INDIAN IRRIGATION PROJECTS § 173.11 Supervision...

25 CFR 173.11 - Supervision of permittees' rates.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false Supervision of permittees' rates. 173.11 Section 173.11 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER CONCESSIONS, PERMITS AND LEASES ON LANDS WITHDRAWN OR ACQUIRED IN CONNECTION WITH INDIAN IRRIGATION PROJECTS § 173.11 Supervision...

25 CFR 173.11 - Supervision of permittees' rates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Supervision of permittees' rates. 173.11 Section 173.11 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER CONCESSIONS, PERMITS AND LEASES ON LANDS WITHDRAWN OR ACQUIRED IN CONNECTION WITH INDIAN IRRIGATION PROJECTS § 173.11 Supervision...

50 CFR 13.23 - Amendment of permits.

Code of Federal Regulations, 2011 CFR

2011-10-01

... amend any permit for just cause at any time during its term, upon written finding of necessity, provided... modified, such permittee must submit a full written justification and supporting information in conformity... permittee is not required to obtain a new permit if there is a change in the legal individual or business...

7 CFR 319.41-4 - Notice of arrival by permittee.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Notice of arrival by permittee. 319.41-4 Section 319.41-4 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FOREIGN QUARANTINE NOTICES Indian Corn or Maize, Broomcorn, and...

9 CFR 116.1 - Applicability and general considerations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... imported products, each permittee shall maintain at the permittee's place of business detailed and accurate... manufacturer may maintain and retain records required under this part at an alternative location. Such authorization shall be confirmed by the filing of an addendum to the plot plan legend. The addendum shall list...

15 CFR 971.503 - Diligent commercial recovery.

Code of Federal Regulations, 2010 CFR

2010-01-01

... flexibility for changes encountered by the permittee in market conditions or other factors. (e) The permittee... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Diligent commercial recovery. 971.503 Section 971.503 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued...

CHLOROBENZENES, CHLOROPHENOLS, PHAS AND LOW CHLORINATED DIOXIN/FURAN POST-BOILER TOXICITY INDICATORS IN MUNICIPAL SOLID WASTE INCINERATORS

EPA Science Inventory

Research has sought indicator compounds for fast and less costly predictive monitoring of polychlorinated dibenzo-p-dioxin and furans, PCDD/F, toxic equivalent concentrations or TEQs. Studies have shown chlorobenzenes and chlorophenols had a good correlation with TEQ, suggesting ...

Continuous monitoring of bacterial attachment

NASA Technical Reports Server (NTRS)

Koeing, D. W.; Mishra, S. K.; Pierson, D. L.

1994-01-01

A major concern with the Space Station Freedom (SSF) water supply system is the control of longterm microbial contamination and biofilm development in the water storage and distribution systems. These biofilms have the potential for harboring pathogens as well as microbial strains containing resistance factors that could negatively influence crew health. The proposed means for disinfecting the water system on SSF (iodine) may encourage the selection of resistant strains. In fact, biofilm bacteria were observed in water lines from the Space Shuttle Columbia (OV-102); therefore, an alternative remediation method is required to disinfect spacecraft water lines. A thorough understanding of colonization events and the physiological parameters that will influence bacteria adhesion is required. The limiting factor for development of this technology is the ability to continuously monitor adhesion events and the effects of biocides on sessile bacteria. Methods were developed to allow bacterial adhesion and subsequent biocidal treatment to be monitored continuously. This technique couples automated image analysis with a continuous flow of a bacterial suspension through an optical flow cell. A strain of Pseudomonas cepacia isolated from the water supply of the Space Shuttle Discovery (OV-103) during STS-39 was grown in a nitrogen-limited continuous culture. This culture was challenged continuously with iodine during growth, and the adhesion characteristics of this strain was measure with regard to flow rate. Various biocides (ozone, hypochlorite, and iodine) were added to the flow stream to evaluate how well each chemical removed the bacteria. After biocide treatment, a fresh bacterial suspension was introduced into the flow cell, and the attachment rate was evaluated on the previously treated surface. This secondary fouling was again treated with biocide to determine the efficacy of multiple batch chemical treatments in removing biofilm.

Loading and release mechanisms of a biocide in polystyrene-block-poly(acrylic acid) block copolymer micelles.

PubMed

Vyhnalkova, Renata; Eisenberg, Adi; van de Ven, Theo G M

2008-07-24

The kinetics of loading of polystyrene197-block-poly(acrylic acid)47 (PS197-b-PAA47) micelles, suspended in water, with thiocyanomethylthiobenzothiazole biocide and its subsequent release were investigated. Loading of the micelles was found to be a two-step process. First, the surface of the PS core of the micelles is saturated with biocide, with a rate determined by the transfer of solid biocide to micelles during transient micelle-biocide contacts. Next, the biocide penetrates as a front into the micelles, lowering the Tg in the process (non-Fickian case II diffusion). The slow rate of release is governed by the height of the energy barrier that a biocide molecule must overcome to pass from PS into water, resulting in a uniform biocide concentration within the micelle, until Tg is increased to the point that diffusion inside the micelles becomes very slow. Maximum loading of biocide into micelles is approximately 30% (w/w) and is achieved in 1 h. From partition experiments, it can be concluded that the biocide has a similar preference for polystyrene as for ethylbenzene over water, implying that the maximum loading is governed by thermodynamics.

25 CFR 166.310 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2011 CFR

2011-04-01

... exposure to disease? 166.310 Section 166.310 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... protect livestock from exposure to disease? In accordance with applicable law, permittees must: (a) Vaccinate livestock; (b) Treat all livestock exposed to or infected with contagious or infectious diseases...

25 CFR 166.310 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2013 CFR

2013-04-01

... exposure to disease? 166.310 Section 166.310 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... protect livestock from exposure to disease? In accordance with applicable law, permittees must: (a) Vaccinate livestock; (b) Treat all livestock exposed to or infected with contagious or infectious diseases...

25 CFR 166.310 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2014 CFR

2014-04-01

... exposure to disease? 166.310 Section 166.310 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... protect livestock from exposure to disease? In accordance with applicable law, permittees must: (a) Vaccinate livestock; (b) Treat all livestock exposed to or infected with contagious or infectious diseases...

25 CFR 166.310 - What must a permittee do to protect livestock from exposure to disease?

Code of Federal Regulations, 2012 CFR

2012-04-01

... exposure to disease? 166.310 Section 166.310 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... protect livestock from exposure to disease? In accordance with applicable law, permittees must: (a) Vaccinate livestock; (b) Treat all livestock exposed to or infected with contagious or infectious diseases...

25 CFR 166.316 - Can a permittee construct improvements on permitted Indian land?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Can a permittee construct improvements on permitted Indian land? 166.316 Section 166.316 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER GRAZING PERMITS Land and Operations Management Conservation Practices and Improvements § 166...

25 CFR 166.314 - Can a permittee apply a conservation practice on permitted Indian land?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Can a permittee apply a conservation practice on permitted Indian land? 166.314 Section 166.314 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER GRAZING PERMITS Land and Operations Management Conservation Practices and Improvements...

43 CFR 29.6 - Financing, accounting, and audit.

Code of Federal Regulations, 2010 CFR

2010-10-01

... each Permittee within a reasonable time as to the date of the tanker loadings and the volumes of TAPS oil loaded. The Permittee will send an invoice for transportation charges for TAPS oil (which includes... to vessels, the amount of fees charged and collected, and the Owners of TAPS oil from whom such fees...

27 CFR 20.60 - Change in name of permittee.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Change in name of permittee. 20.60 Section 20.60 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... appropriate TTB officer. (Approved by the Office of Management and Budget under control number 1512-0336) [T.D...

14 CFR 437.71 - Flight rules.

Code of Federal Regulations, 2013 CFR

2013-01-01

... rocket-powered flight, a permittee must confirm that all systems and operations necessary to ensure that... endanger the public. (c) A permittee may not operate a reusable suborbital rocket in a careless or reckless... operate a reusable suborbital rocket in areas designated in a Notice to Airmen under § 91.137, § 91.138...

14 CFR 437.71 - Flight rules.

Code of Federal Regulations, 2014 CFR

2014-01-01

... rocket-powered flight, a permittee must confirm that all systems and operations necessary to ensure that... endanger the public. (c) A permittee may not operate a reusable suborbital rocket in a careless or reckless... operate a reusable suborbital rocket in areas designated in a Notice to Airmen under § 91.137, § 91.138...

14 CFR 437.71 - Flight rules.

Code of Federal Regulations, 2011 CFR

2011-01-01

... rocket-powered flight, a permittee must confirm that all systems and operations necessary to ensure that... endanger the public. (c) A permittee may not operate a reusable suborbital rocket in a careless or reckless... operate a reusable suborbital rocket in areas designated in a Notice to Airmen under § 91.137, § 91.138...

14 CFR 437.71 - Flight rules.

Code of Federal Regulations, 2012 CFR

2012-01-01

... rocket-powered flight, a permittee must confirm that all systems and operations necessary to ensure that... endanger the public. (c) A permittee may not operate a reusable suborbital rocket in a careless or reckless... operate a reusable suborbital rocket in areas designated in a Notice to Airmen under § 91.137, § 91.138...

14 CFR 437.71 - Flight rules.

Code of Federal Regulations, 2010 CFR

2010-01-01

... rocket-powered flight, a permittee must confirm that all systems and operations necessary to ensure that... endanger the public. (c) A permittee may not operate a reusable suborbital rocket in a careless or reckless... operate a reusable suborbital rocket in areas designated in a Notice to Airmen under § 91.137, § 91.138...

Resistance of Bacteria to Biocides.

PubMed

Maillard, Jean-Yves

2018-04-01

Biocides and formulated biocides are used worldwide for an increasing number of applications despite tightening regulations in Europe and in the United States. One concern is that such intense usage of biocides could lead to increased bacterial resistance to a product and cross-resistance to unrelated antimicrobials including chemotherapeutic antibiotics. Evidence to justify such a concern comes mostly from the use of health care-relevant bacterial isolates, although the number of studies of the resistance characteristics of veterinary isolates to biocides have increased the past few years. One problem remains the definition of "resistance" and how to measure resistance to a biocide. This has yet to be addressed globally, although the measurement of resistance is becoming more pressing, with regulators both in Europe and in the United States demanding that manufacturers provide evidence that their biocidal products will not impact on bacterial resistance. Alongside in vitro evidence of potential antimicrobial cross-resistance following biocide exposure, our understanding of the mechanisms of bacterial resistance and, more recently, our understanding of the effect of biocides to induce a mechanism(s) of resistance in bacteria has improved. This article aims to provide an understanding of the development of antimicrobial resistance in bacteria following a biocide exposure. The sections provide evidence of the occurrence of bacterial resistance and its mechanisms of action and debate how to measure bacterial resistance to biocides. Examples pertinent to the veterinary field are used where appropriate.

Effect Of Inorganic, Synthetic And Naturally Occurring Chelating Agents On Fe(II) Mediated Advanced Oxidation Of Chlorophenols

EPA Science Inventory

This study examines the feasibility and application of Advanced Oxidation Technologies (AOTs) for the treatment of chlorophenols that are included in US EPA priority pollutant list. A novel class of sulfate/hydroxyl radical-based homogeneous AOTs (Fe(II)/PS, Fe(II)/PMS, Fe(II)/H...

Australian DefenceScience. Volume 13. Number 1, Autumn

DTIC Science & Technology

2005-01-01

marine communities in the surrounding environment. Antifouling paints containing the agent tributyltin ( TBT ) were recently banned under a new...are presently seen as the most promising non- toxic alternative to biocidal antifouling paints. However, some diatoms still adhere to these surfaces

Synergistic activity of biocides and antibiotics on resistant bacteria from organically produced foods.

PubMed

Fernández Fuentes, Miguel Angel; Abriouel, Hikmate; Gadea, Rebeca; Pérez Pulido, Rubén; Gálvez, Antonio; Ortega, Elena

2014-10-01

Synergism between biocides and antibiotics was investigated in 20 biocide and antibiotic-resistant bacterial strains that were previously isolated from organically produced foods, according to their antimicrobial resistance profiles. Most of the antibiotic/biocide combinations yielded synergistic interactions, reducing the inhibitory concentrations of biocides and antibiotics by 4- to 16-fold. Among enterococci, synergism with biocides was detected for amoxicillin (AM), cefuroxime (CX), erythromycin (EM), ciprofloxacin (CP), and trimethoprim/sulphametoxazol (T/S). Among staphylococci, interactions were synergistic (AM) and either synergistic or indifferent (CX and EM, depending on biocide). Among the three methicillin-resistant Staphylococcus aureus clinical strains included in the study, the combinations of methicillin and triclosan or hexachlorophene acted synergistically in all strains, but interactions were either synergistic or indifferent for the other biocides, depending on the strain. All combinations tested were synergistic for Lactobacillus (AM, CX, EM, and CP) and Micrococcus (AM, EM). In Salmonella, interactions were indifferent (AM, CX, EM, and CP) or synergistic (T/S). Synergism with biocides was also detected in Klebsiella isolates (AM, CX, and T/S), Enterobacter sp. (AM, CX, EM, and T/S), Pantoea (AM, CX, EM, CP, and T/S), and Chryseobacterium sp. (EM). These results suggest that combinations of biocides and antibiotics may open new possibilities to combat antimicrobial resistance.

Halloysite clay nanotubes for controlled release of protective agents.

PubMed

Lvov, Yuri M; Shchukin, Dmitry G; Möhwald, Helmuth; Price, Ronald R

2008-05-01

Halloysite aluminosilicate nanotubes with a 15 nm lumen, 50 nm external diameter, and length of 800 +/- 300 nm have been developed as an entrapment system for loading, storage, and controlled release of anticorrosion agents and biocides. Fundamental research to enable the control of release rates from hours to months is being undertaken. By variation of internal fluidic properties, the formation of nanoshells over the nanotubes and by creation of smart caps at the tube ends it is possible to develop further means of controlling the rate of release. Anticorrosive halloysite coatings are in development and a self-healing approach has been developed for repair mechanisms through response activation to external impacts. In this Perspective, applications of halloysite as nanometer-scale containers are discussed, including the use of halloysite tubes as drug releasing agents, as biomimetic reaction vessels, and as additives in biocide and protective coatings. Halloysite nanotubes are available in thousands of tons, and remain sophisticated and novel natural nanomaterials which can be used for the loading of agents for metal and plastic anticorrosion and biocide protection.

27 CFR 22.61 - Change in name of permittee.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Change in name of permittee. 22.61 Section 22.61 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... the Office of Management and Budget under control number 1512-0335) [T.D. ATF-199, 50 FR 9183, Mar. 6...

27 CFR 22.61 - Change in name of permittee.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Change in name of permittee. 22.61 Section 22.61 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... the Office of Management and Budget under control number 1512-0335) [T.D. ATF-199, 50 FR 9183, Mar. 6...

27 CFR 1.40 - Change of name.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Change of name. 1.40... Amendment and Duration of Basic Permits § 1.40 Change of name. In the event of any change in the name (trade or corporate name) of a permittee, or, in the event a permittee desires to engage in operations under...

27 CFR 1.40 - Change of name.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Change of name. 1.40... Amendment and Duration of Basic Permits § 1.40 Change of name. In the event of any change in the name (trade or corporate name) of a permittee, or, in the event a permittee desires to engage in operations under...

27 CFR 1.40 - Change of name.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Change of name. 1.40... Amendment and Duration of Basic Permits § 1.40 Change of name. In the event of any change in the name (trade or corporate name) of a permittee, or, in the event a permittee desires to engage in operations under...

27 CFR 1.40 - Change of name.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Change of name. 1.40... Amendment and Duration of Basic Permits § 1.40 Change of name. In the event of any change in the name (trade or corporate name) of a permittee, or, in the event a permittee desires to engage in operations under...

27 CFR 1.40 - Change of name.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Change of name. 1.40... Amendment and Duration of Basic Permits § 1.40 Change of name. In the event of any change in the name (trade or corporate name) of a permittee, or, in the event a permittee desires to engage in operations under...

30 CFR 251.11 - Submission, inspection, and selection of geological data and information collected under a permit...

Code of Federal Regulations, 2010 CFR

2010-07-01

... geological data and information collected under a permit and processed by permittees or third parties. 251.11... GEOLOGICAL AND GEOPHYSICAL (G&G) EXPLORATIONS OF THE OUTER CONTINENTAL SHELF § 251.11 Submission, inspection, and selection of geological data and information collected under a permit and processed by permittees...

47 CFR 73.3540 - Application for voluntary assignment or transfer of control.

Code of Federal Regulations, 2010 CFR

2010-10-01

... control of a corporate licensee or permittee for an FM or TV translator station, a low power TV station and any associated auxiliary station, such as translator microwave relay stations and UHF translator... Licensee or Permittee, or Assignment of License or Permit for an FM or TV translator Station, or a Low...

Nonhazardous Urine Pretreatment Method

NASA Technical Reports Server (NTRS)

Akse, James R.; Holtsnider, John T.

2012-01-01

A method combines solid phase acidification with two non-toxic biocides to prevent ammonia volatilization and microbial proliferation. The safe, non-oxidizing biocide combination consists of a quaternary amine and a food preservative. This combination has exhibited excellent stabilization of both acidified and unacidified urine. During pretreatment tests, composite urine collected from donors was challenged with a microorganism known to proliferate in urine, and then was processed using the nonhazardous urine pre-treatment method. The challenge microorganisms included Escherichia coli, a common gram-negative bacteria; Enterococcus faecalis, a ureolytic gram-positive bacteria; Candida albicans, a yeast commonly found in urine; and Aspergillus niger, a problematic mold that resists urine pre-treatment. Urine processed in this manner remained microbially stable for over 57 days. Such effective urine stabilization was achieved using non-toxic, non-oxidizing biocides at higher pH (3.6 to 5.8) than previous methods in use or projected for use aboard the International Space Station (ISS). ISS urine pretreatment methods employ strong oxidants including ozone and hexavalent chromium (Cr(VI)), a carcinogenic material, under very acidic conditions (pH = 1.8 to 2.4). The method described here offers a much more benign chemical environment than previous pretreatment methods, and will lower equivalent system mass (ESM) by reducing containment volume and mass, system complexity, and crew time needed to handle pre-treatment chemicals. The biocides, being non-oxidizing, minimize the potential for chemical reactions with urine constituents to produce volatile, airborne contaminants such as cyanogen chloride. Additionally, the biocides are active under significantly less acidic conditions than those used in the current system, thereby reducing the degree of required acidification. A simple flow-through solid phase acidification (SPA) bed is employed to overcome the natural buffering capacity of urine, and to lower the pH to levels that fix ammoniacal nitrogen in the non-volatile and highly water soluble NH4 + form. Citric acid, a highly soluble, solid tricarboxylic acid essential to cellular metabolism, and typically used as a food preservative, has also been shown to efficiently acidify urine in conjunction with non-oxidizing biocides to provide effective stabilization with respect to both microbial growth and ammonia volatilization.

Synthesis of ethylene maleic anhydride copolymer containing fungicides and evaluation of their effect for wood decay resistance

Treesearch

George C. Chen

2008-01-01

The aim of the present study was to combat wood decay based on the approach controlled-release biocides from polymers. The possibility of introducing polymer-bonded fungicides into the cell lumens was investigated. The synthesis of ethylene maleic anhydride copolymer containing pentachlorophenol (penta) and 8-hydroxy quinoline (8HQ) in N, N dimethyl formamide is...

Adsorption interactions of humic acids with biocides

NASA Astrophysics Data System (ADS)

Mal'Tseva, E. V.; Ivanov, A. A.; Yudina, N. V.

2009-11-01

The chemical composition of humic acids from brown coal (Aldrich) was determined by element analysis, 13C NMR spectroscopy, and potentiometric titration. The adsorption ability of humic acids with different biocides (cyproconasol, propiconasol, tebuconasol, irgarol 1051, and DCOIT) was studied. The adsorption ability of a mixture of biocides in aqueous solutions was higher than that of the individual components. The limiting concentration of humic acids at which adsorption of biocides was maximum was determined. Adsorption constants were calculated by the Freundlich equation for each biocide in aqueous solution.

Encapsulation of Antifouling Organic Biocides in Poly(lactic acid) Nanoparticles

PubMed Central

Kamtsikakis, Aristotelis; Kavetsou, Eleni; Chronaki, Konstantina; Kiosidou, Evangelia; Pavlatou, Evangelia; Karana, Alexandra; Papaspyrides, Constantine; Detsi, Anastasia; Karantonis, Antonis; Vouyiouka, Stamatina

2017-01-01

The scope of the current research was to assess the feasibility of encapsulating three commercial antifouling compounds, Irgarol 1051, Econea and Zinc pyrithione, in biodegradable poly(lactic acid) (PLA) nanoparticles. The emulsification–solvent evaporation technique was herein utilized to manufacture nanoparticles with a biocide:polymer ratio of 40%. The loaded nanoparticles were analyzed for their size and size distribution, zeta potential, encapsulation efficiency and thermal properties, while the relevant physicochemical characteristics were correlated to biocide–polymer system. In addition, the encapsulation process was scaled up and the prepared nanoparticles were dispersed in a water-based antifouling paint in order to examine the viability of incorporating nanoparticles in such coatings. Metallic specimens were coated with the nanoparticles-containing paint and examined regarding surface morphology. PMID:28952560

Antiseptic resistance: what do we know and what does it mean?

PubMed

Sheldon, Albert T

2005-01-01

Biocides (antiseptics, disinfectants, preservatives, sterilants) are used in clinical medicine as intervention strategies that prevent the dissemination of nosocomial pathogens. Biocides are also used for personal hygiene and to prevent cross-contamination of food-borne pathogens in homes, restaurants, day care centers, and nursing homes. However, laboratory evidence has emerged suggesting that the mechanism of nonsusceptibility to biocides may counter-select for resistance to antibiotics. Nature conserves successful survival strategies. Using existing mechanisms of resistance to antibiotics and their means of dissemination, microorganisms have adopted this same survival strategy for biocide nonsusceptibility. These mechanisms are intrinsic in nature or are acquired. The consequences to biocide efficacy in the clinical setting are probably not significant from the biocide perspective. But, the selective pressure biocides exert on bacterial populations that have mechanisms of resistance similar to those to antibiotics or that are also substrates for antibiotic resistance is of concern.

Emergent behaviour in a chlorophenol-mineralising three-tiered microbial ‘food web’

PubMed Central

Wade, M.J.; Pattinson, R.W.; Parker, N.G.; Dolfing, J.

2016-01-01

Anaerobic digestion enables the water industry to treat wastewater as a resource for generating energy and recovering valuable by-products. The complexity of the anaerobic digestion process has motivated the development of complex models. However, this complexity makes it intractable to pin-point stability and emergent behaviour. Here, the widely used Anaerobic Digestion Model No. 1 (ADM1) has been reduced to its very backbone, a syntrophic two-tiered microbial ‘food chain’ and a slightly more complex three-tiered microbial ‘food web’, with their stability analysed as a function of the inflowing substrate concentration and dilution rate. Parameterised for phenol and chlorophenol degradation, steady-states were always stable and non-oscillatory. Low input concentrations of chlorophenol were sufficient to maintain chlorophenol- and phenol-degrading populations but resulted in poor conversion and a hydrogen flux that was too low to sustain hydrogenotrophic methanogens. The addition of hydrogen and phenol boosted the populations of all three organisms, resulting in the counterintuitive phenomena that (i) the phenol degraders were stimulated by adding hydrogen, even though hydrogen inhibits phenol degradation, and (ii) the dechlorinators indirectly benefitted from measures that stimulated their hydrogenotrophic competitors; both phenomena hint at emergent behaviour. PMID:26551153

Solid-phase microextraction based on polyaniline doped with perfluorooctanesulfonic acid coupled to HPLC for the quantitative determination of chlorophenols in water samples.

PubMed

He, Huan; Zhuang, Yuan; Peng, Ying; Gao, Zhanqi; Yang, Shaogui; Sun, Cheng

2014-02-01

A porous and highly efficient polyaniline-based solid-phase microextraction (SPME) coating was successfully prepared by the electrochemical deposition method. A method based on headspace SPME followed by HPLC was established to rapidly determine trace chlorophenols in water samples. Influential parameters for the SPME, including extraction mode, extraction temperature and time, pH and ionic strength procedures, were investigated intensively. Under the optimized conditions, the proposed method was linear in the range of 0.5-200 μg/L for 4-chlorophenol and 2,4,6-trichlorophenol, 0.2-200 μg/L for 2,4-dichlorophenol and 2-200 μg/L for 2,3,4,6-tetrachlorophenol and pentachlorophenol, with satisfactory correlation coefficients (>0.99). RSDs were <15% (n = 5) and LODs were relatively low (0.10-0.50 μg/L). Compared to commercial 85 μm polyacrylate and 60 μm polydimethylsiloxane/divinylbenzene fibers, the homemade polyaniline fiber showed a higher extraction efficiency. The proposed method has been successfully applied to the determination of chlorophenols in water samples with satisfactory recoveries. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Pentachlorophenol and cancer risk: Focusing the lens on ...

EPA Pesticide Factsheets

Objective: Pentachlorophenol is a fungicide widely used as a wood preservative, classified in 1999 by the International Agency for Research on Cancer as a “possible human carcinogen”. We review currently available epidemiological research to determine the extent to which recent studies address the limitations of the previous data, particularly with respect to distinguishing the effect of pentachlorophenol from that of its contaminants (e.g., dioxins) and other chlorophenols. Data Sources and Extraction: We examined published studies with a quantitative or qualitative pentachlorophenol measure, or an assessment of chlorophenol exposure and additional information on specific jobs that would likely have used pentachlorophenol rather than other chlorophenols. The data collection process focused on results pertaining specifically to all cancer sites and specific hematopoietic cancers, and data pertaining to risks associated with other types of chlorophenols, dioxins, or furans. Synthesis: In contrast with dioxin, pentachlorophenol exposure was not associated with total cancer incidence or mortality. However, the pentachlorophenol studies present considerable evidence pertaining to lymphopoietic cancers, with strong associations seen in multiple studies, in different locations and using different designs. The extension of a large cohort study of sawmill workers, with follow-up to 1995, provides information about risks of relatively rare cancers (e.g.,

Chlorophenols in leachates originating from different landfills and aerobic composting plants.

PubMed

Ozkaya, Bestamin

2005-09-30

Both type and concentration of organic contaminants in landfill leachates show great variation depending on many factors, such as type of wastes, rate of water application, moisture content, landfill design and operation age. In this paper, highly toxic chlorophenol derivatives, poorly biodegradable, carcinogenic existence and recalcitrant properties are determined by solid phase microextraction (SPME)-GC/FID in different leachates from landfill and composting plant in Istanbul. Leachates originated from acidogenic, methanogenic phases of Odayeri sanitary landfill (OSL) and from an aerobic composting plant are considered for different chlorophenol types. It is observed that acidogenic leachate from Odayeri landfill includes 2,4-dichlorophenol, 2,6-dichlorophenol, 2,3,4-trichlorophenol, 2,3,4,5-tetrachlorophenol and 2,3,4,6-tetrachlorophenol at concentration ranges, 15-130, 18-65, 8-40, 5-20 and 10-25 microg/l, respectively. Whereas, only 2,4-dichlorophenol at a concentration range 8-40 microg/l is determined in the methanogenic leachate of the landfill, which can be considered as an indication of reductive dechlorination. There is no chlorophenol derivative in aerobic composting leachate. It is determined that acidogenic leachate from Odayeri landfill includes more species of chlorinated phenols at higher concentration.

Zebrafish Functional Genetics Approach to the Pathogenesis of Well-Differentiated Liposarcoma

DTIC Science & Technology

2014-10-01

is the most common soft-tissue sarcoma of humans, and predis- posing factors include exposure to dioxin -containing herbicidal agents used during the...is completely refractory to chemotherapy and radiation. Exposure to dioxin -based herbicidal agents (Agent Orange) and to radiation are known predis...34Cancer  mortality  in  workers  exposed  to  phenoxy  herbicides,  chlorophenols,  and  dioxins .  An  expanded  and  updated  international  cohort

Characterization of biocide-tolerant bacteria isolated from cheese and dairy small-medium enterprises.

PubMed

Fernández Márquez, Ma Luisa; Grande Burgos, Ma José; López Aguayo, Ma Carmen; Pérez Pulido, Rubén; Gálvez, Antonio; Lucas, Rosario

2017-04-01

A collection of 120 bacterial isolates from small medium enterprises involved in the production of cow milk and the manufacture of goat cheese were screened for sensitivity to biocides benzalkonium chloride (BC), cetrimide (CT), hexadecylpyridinium chloride (HDP), triclosan (TC), hexachlorophene (CF) and poly-(hexamethylen guanidinium) hydrochloride (PHMG). Nineteen isolates were selected according to biocide tolerance and identified by 16S rDNA sequencing as Lactococcus sp. (6) Enterococcus sp. (1), Lactobacillus sp. (4), Bacillus sp. (1) Escherichia sp. (5), Enterobacter sp. (1) and Helicobacter sp. (1). These were further characterised regarding antimicrobial resistance phenotype and genotype. Several isolates were multiply (3 or more) tolerant to biocides or resistant to antibiotics, but only two Escherichia sp. isolates and Enterobacter sp. were multiply resistant to biocides and antibiotics. Statistical analysis of biocide tolerance and antibiotic resistance revealed significant positive correlations between different biocides and between biocides and antibiotics. The biocide tolerance genes most frequently found were qacEΔ1 and qacA/B. The sulfonamide resistance gene sul1 was found in two Escherichia sp. isolates and in Enterobacter sp., all of which also carried qacEΔ1. Beta-lactam (bla CTX-M , bla PSE ) and tetracycline resistance genes [tet(A), tet(C) and tet(D)] were detected. Efflux pump genes acrB and mdfA were found in most Gram-negative isolates. Results from the study suggest that exposure to biocides can indirectly select for antibiotic resistance. Copyright © 2016 Elsevier Ltd. All rights reserved.

Possible underestimations of risks for the environment due to unregulated emissions of biocides from households to wastewater.

PubMed

Wieck, Stefanie; Olsson, Oliver; Kümmerer, Klaus

2016-09-01

The aim of this study was to investigate the role of household products as possible sources of biocidal active substances in municipal wastewater and their regulation under the Biocidal Products Regulation (EU) 528/2012. In 131 households, we investigated the prevalence of products used to control pests, washing and cleaning agents and select personal care products with high release to wastewater. Inventories of these products were established with the help of barcode scanning. All uses of biocidal active substances were evaluated regarding their assessment under the Biocidal Products Regulation. 2963 products were scanned in total, with 48% being washing and cleaning agents, 43% personal care products and 9% products used to control pests. Biocidal active substances were found in each household. These were observed primarily in washing and cleaning agents and personal care products (90%), while only a small percentage of the observations of biocidal active substances was in biocidal products. 64% of the observations of biocidal active substances were in applications that do not fall under the Biocidal Products Regulation and are thus not subject to its environmental risk assessment. This study shows clearly that risks for the environment are underestimated because unregulated emissions to wastewater occur. It demonstrates that there are gaps in the current chemical legislation that lead to a release of substances into wastewater that were not subject to environmental risk assessment under the Biocidal Products Regulation. This is one example of the limitations of scientific risk assessment of chemicals - its complexity is immense. From our point of view, the results underline the importance of a sustainable use of the substances as this is the only way to decrease yet unidentified risks. Copyright © 2016 Elsevier Ltd. All rights reserved.

Adsorbed states of chlorophenol on Cu(110) and controlled switching of single-molecule junctions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okuyama, H., E-mail: hokuyama@kuchem.kyoto-u.ac.jp; Kitaguchi, Y.; Hattori, T.

A molecular junction of substituted benzene (chlorophenol) is fabricated and controlled by using a scanning tunneling microscope (STM). Prior to the junction formation, the bonding geometry of the molecule on the surface is characterized by STM and electron energy loss spectroscopy (EELS). EELS shows that the OH group of chlorophenol is dissociated on Cu(110) and that the molecule is bonded nearly flat to the surface via an O atom, with the Cl group intact. We demonstrate controlled contact of an STM tip to the “available” Cl group and lift-up of the molecule while it is anchored to the surface viamore » an O atom. The asymmetric bonding motifs of the molecule to the electrodes allow for reversible control of the junction.« less

Consumers' perceptions of biocidal products in households.

PubMed

Wieck, Stefanie; Olsson, Oliver; Kümmerer, Klaus

2018-03-01

Biocidal products are commonly used in households and can pose a risk to human health and the environment. The aim of this study was to evaluate consumers' use and understanding of biocidal products in order to identify starting points for minimising their exposure to these products and reducing possible emissions to the environment. In a case study, standardised questionnaires were used to interview consumers in 133 households in three neighbourhoods in Northern Germany, representing the urban-rural typologies in Europe: predominantly urban, intermediate and predominantly rural regions. The questions focussed on the comprehension of the term 'biocide', pest control habits, sources of information, risk perception of different product groups and possible emission reduction measures. Only 21% of the respondents understood the term 'biocide' correctly, whereas 29% thought of 'something that had to do with organic pest control', and 28% were not able to think of a possible meaning. The risk perception of biocidal products compared to plant protection products varied depending on the living conditions. In the urban neighbourhood, biocidal products were perceived as more dangerous than in the rural area. The main pests to be fought were ants, mould and fruit fly. The results of the study indicate that there is a considerable difference between the types of biocidal products that interviewees claimed to own and those that they actually did have in their households. Most notably, respondents did not realise that they owned surface disinfectants. This result indicates that consumers often seem not to be aware of using specific biocidal products. Also, this shows the limitations of collecting data on products owned with only one method, as the results from products inventories of the households deviate from the data collected in interviews. Our results show that the term 'biocide' is not fully understood by many people. To communicate possible risks of biocidal products, other terms would have to be used. Online information regarding general facts on necessary general hygiene measures and biocidal products against bacteria and insects are likely to be of highest relevance for consumers. However, risk communication for biocidal products in general is difficult because consumers are often not aware of using biocidal products. For this reason, information and awareness raising campaigns should be accompanied by further measures such as sales restrictions for specific user-groups or prohibitions of certain uses for a sustainable use of biocidal products. Copyright © 2017 Elsevier GmbH. All rights reserved.

25 CFR 166.421 - If a permit is canceled for non-payment, does that extinguish the permittee's debt?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false If a permit is canceled for non-payment, does that extinguish the permittee's debt? 166.421 Section 166.421 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE... Rental Payment Collections § 166.421 If a permit is canceled for non-payment, does that extinguish the...

Chapter 14: Evaluating the Leaching of Biocides from Preservative-Treated Wood Products

Treesearch

Stan T. Lebow

2014-01-01

Leaching of biocides is an important consideration in the long term durability and any potential for environmental impact of treated wood products. This chapter discusses factors affecting biocide leaching, as well as methods of evaluating rate and quantity of biocide released. The extent of leaching is a function of preservative formulation, treatment methods, wood...

Protecting wood from mould, decay, and termites with multi-component biocide systems

Treesearch

Carol A. Clausen

2007-01-01

Biocides must be developed for controlling mould establishment on cellulose-based building materials. Accordingly, biocides intended for indoor applications must be non- toxic, non-volatile, odourless, hypoallergenic, and able to provide long-term protection under conditions of high humidity. Multi-component biocide systems were tested in American Wood-Preservers’...

Virulence factors and antimicrobial resistance in Escherichia coli strains isolated from hen egg shells.

PubMed

Grande Burgos, María José; Fernández Márquez, Maria Luisa; Pérez Pulido, Rubén; Gálvez, Antonio; Lucas López, Rosario

2016-12-05

Eggs may contain extraintestinal pathogenic (ExPEC) and diarrheogenic (DEC) Escherichia coli which in addition may carry antibiotic resistance. The wide use of biocides and disinfectants in the food industry may induce biocide tolerance in bacteria. The aim of the present study was to evaluate biocide tolerance and antibiotic resistance in E. coli from hen egg shells. A total of 27 isolates obtained from a screening of 180 eggs were studied. Seven isolates carried both eae and bfpA genes of typical enteropathogenic E. coli (EPEC) strains, while 14 isolates only carried eae associated with atypical EPEC strains. Shiga toxin genes stx and stx2 were detected in four isolates. Heat-stable and heat-labile enterotoxin genes as well as aggR were also detected. Several isolates had minimum inhibitory concentrations (MICs) that were higher than the wild-type for the biocide hexadecylpyridinium chloride (HDP, 18.52%) or the commercial disinfectant P3 oxonia (OX, 14.81%). Antibiotic resistance was detected for ampicillin (37.03%), streptomycin (37.03%), tetracycline (37.03%), chloramphenicol (11.11%), nalidixic acid (18.51%) and trimethoprim-sulfamethoxazole (14.81%). Eight isolates (29.63%) were biocide tolerant and antibiotic resistant. Efflux pump genes detected included acrB (96.29%), mdfA (85.18%) and oxqA (37.03%), in addition to quaternary ammonium compound (QAC) resistance genes qacA/B (11.11%) and qacE (7.40%). Antibiotic resistance genes detected included bla CTX-M-2 (22.22%), bla TEM (3.70%), bla PSE (3.70%), tet(A) (29.63%), tet(B) (29.63%), tet(C) (7.40%), tet(E) (11.11%), aac(6')-Ib (3.70%), sul1 (14.81%), dfrA12 (3.70%) and dfrA15 (3.70%). Most isolates (96.30%) carried more than one genetic determinant of resistance. The most frequent combinations were efflux pump components acrB and mdfA with tetracycline resistance genes (33.33% of isolates). Isolates carrying QAC resistance genes also carried between 4 and 8 of the additional antimicrobial resistance genes investigated. Regardless of biocide tolerance and antibiotic resistance, all isolates were sensitive to carvacrol (0.25%), thymol (0.125%) and trisodium phosphate (1 to 1.5%), but they exhibited a heterogeneous response to sodium lactate and lysozyme-EDTA combinations that apparently were not related with antibiotic resistance. Results from the study reveal not only a low incidence of biocide tolerance but also the presence of multiple resistance strains carrying multiple genetic determinants of resistance. Copyright © 2016 Elsevier B.V. All rights reserved.

Anaerobic dechlorination of 2,4-dichlorophenol in freshwater sediments in the presence of sulfate.

PubMed Central

Kohring, G W; Zhang, X M; Wiegel, J

1989-01-01

In the presence of added sulfate, 2,4-dichlorophenol and 4-chlorophenol were transformed stoichiometrically to 4-chlorophenol and phenol, respectively, in anaerobic freshwater lake sediments between 18 and 40 degrees C. The concomitantly occurring sulfate reduction reduced the initial sulfate concentration from 25 mM to about 6 to 8 mM and depressed methane formation. PMID:2604410

Room-temperature Pd-catalyzed C-H chlorination by weak coordination: one-pot synthesis of 2-chlorophenols with excellent regioselectivity.

PubMed

Sun, Xiuyun; Sun, Yonghui; Zhang, Chao; Rao, Yu

2014-02-07

A room-temperature Pd(II)-catalyzed regioselective chlorination reaction has been developed for a facile one-pot synthesis of a broad range of 2-chlorophenols. The reaction demonstrates an excellent regioselectivity and reactivity for C-H chlorination. This reaction represents one of the rare examples of mild C-H functionalization at ambient temperature.

Risks of Using Antifouling Biocides in Aquaculture

PubMed Central

Guardiola, Francisco Antonio; Cuesta, Alberto; Meseguer, José; Esteban, Maria Angeles

2012-01-01

Biocides are chemical substances that can deter or kill the microorganisms responsible for biofouling. The rapid expansion of the aquaculture industry is having a significant impact on the marine ecosystems. As the industry expands, it requires the use of more drugs, disinfectants and antifoulant compounds (biocides) to eliminate the microorganisms in the aquaculture facilities. The use of biocides in the aquatic environment, however, has proved to be harmful as it has toxic effects on the marine environment. Organic booster biocides were recently introduced as alternatives to the organotin compounds found in antifouling products after restrictions were imposed on the use of tributyltin (TBT). The replacement products are generally based on copper metal oxides and organic biocides. The biocides that are most commonly used in antifouling paints include chlorothalonil, dichlofluanid, DCOIT (4,5-dichloro-2-n-octyl-4-isothiazolin-3-one, Sea-nine 211®), Diuron, Irgarol 1051, TCMS pyridine (2,3,3,6-tetrachloro-4-methylsulfonyl pyridine), zinc pyrithione and Zineb. There are two types of risks associated with the use of biocides in aquaculture: (i) predators and humans may ingest the fish and shellfish that have accumulated in these contaminants and (ii) the development of antibiotic resistance in bacteria. This paper provides an overview of the effects of antifouling (AF) biocides on aquatic organisms. It also provides some insights into the effects and risks of these compounds on non-target organisms. PMID:22408407

Risks of using antifouling biocides in aquaculture.

PubMed

Guardiola, Francisco Antonio; Cuesta, Alberto; Meseguer, José; Esteban, Maria Angeles

2012-01-01

Biocides are chemical substances that can deter or kill the microorganisms responsible for biofouling. The rapid expansion of the aquaculture industry is having a significant impact on the marine ecosystems. As the industry expands, it requires the use of more drugs, disinfectants and antifoulant compounds (biocides) to eliminate the microorganisms in the aquaculture facilities. The use of biocides in the aquatic environment, however, has proved to be harmful as it has toxic effects on the marine environment. Organic booster biocides were recently introduced as alternatives to the organotin compounds found in antifouling products after restrictions were imposed on the use of tributyltin (TBT). The replacement products are generally based on copper metal oxides and organic biocides. The biocides that are most commonly used in antifouling paints include chlorothalonil, dichlofluanid, DCOIT (4,5-dichloro-2-n-octyl-4-isothiazolin-3-one, Sea-nine 211(®)), Diuron, Irgarol 1051, TCMS pyridine (2,3,3,6-tetrachloro-4-methylsulfonyl pyridine), zinc pyrithione and Zineb. There are two types of risks associated with the use of biocides in aquaculture: (i) predators and humans may ingest the fish and shellfish that have accumulated in these contaminants and (ii) the development of antibiotic resistance in bacteria. This paper provides an overview of the effects of antifouling (AF) biocides on aquatic organisms. It also provides some insights into the effects and risks of these compounds on non-target organisms.

Biocidal additives for lubricating/cooling fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morozova, L.P.; Klyavlina, E.A.; Lebedev, E.V.

1984-03-01

This article reports on the synthesis of new biocidal products for the protection of water emulsions of lubricating/cooling fluids (LCFs) against microbiological damage. The new biocides are based on compounds belonging to the classes of oxazolidines and oxazines, and also compounds of these classes but activated by nitro derivatives of aromatic hydrocarbons. Results are presented from evaluations of the biocidal activity of the new products with respect to aerobes, anaerobes, and fungi growing in a 3% emulsion of the widely used LCF Ukrinol-1. The comparative evaluation was based on the optimal biocidal concentration corresponding to the smallest quantity of addedmore » biocide to give maximum suppression of the microorganisms in a minimum time, and with the longest period of effectiveness. The lubricating properties of the biocides were evaluated in an emulsion of the Ukrinol-1 LCF is a four-ball tester. It is concluded that the developed biocides are homogeneous, transparent liquids with a specific odor and can be considered as nontoxic to man; they mix readily with components used in formulating LCFs and detergents (sulfonates, oxyethylated alcohols, phenols, polyglycols, fatty acid soaps, etc.). They are readily soluble in water and in oils. Includes 3 tables.« less

Predicting herbicide and biocide concentrations in rivers across Switzerland

NASA Astrophysics Data System (ADS)

Wemyss, Devon; Honti, Mark; Stamm, Christian

2014-05-01

Pesticide concentrations vary strongly in space and time. Accordingly, intensive sampling is required to achieve a reliable quantification of pesticide pollution. As this requires substantial resources, loads and concentration ranges in many small and medium streams remain unknown. Here, we propose partially filling the information gap for herbicides and biocides by using a modelling approach that predicts stream concentrations without site-specific calibration simply based on generally available data like land use, discharge and nation-wide consumption data. The simple, conceptual model distinguishes herbicide losses from agricultural fields, private gardens and biocide losses from buildings (facades, roofs). The herbicide model is driven by river discharge and the applied herbicide mass; the biocide model requires precipitation and the footprint area of urban areas containing the biocide. The model approach allows for modelling concentrations across multiple catchments at the daily, or shorter, time scale and for small to medium-sized catchments (1 - 100 km2). Four high resolution sampling campaigns in the Swiss Plateau were used to calibrate the model parameters for six model compounds: atrazine, metolachlor, terbuthylazine, terbutryn, diuron and mecoprop. Five additional sampled catchments across Switzerland were used to directly compare the predicted to the measured concentrations. Analysis of the first results reveals a reasonable simulation of the concentration dynamics for specific rainfall events and across the seasons. Predicted concentration ranges are reasonable even without site-specific calibration. This indicates the transferability of the calibrated model directly to other areas. However, the results also demonstrate systematic biases in that the highest measured peaks were not attained by the model. Probable causes for these deviations are conceptual model limitations and input uncertainty (pesticide use intensity, local precipitation, etc.). Accordingly, the model will be conceptually improved. This presentation will present the model simulations and compare the performance of the original and the modified model versions. Finally, the model will be applied across approximately 50% of the catchments in the Swiss Plateau, where necessary input data is available and where the model concept can be reasonably applied.

Biocides in the Yangtze River of China: spatiotemporal distribution, mass load and risk assessment.

PubMed

Liu, Wang-Rong; Zhao, Jian-Liang; Liu, You-Sheng; Chen, Zhi-Feng; Yang, Yuan-Yuan; Zhang, Qian-Qian; Ying, Guang-Guo

2015-05-01

Nineteen biocides were investigated in the Yangtze River to understand their spatiotemporal distribution, mass loads and ecological risks. Fourteen biocides were detected, with the highest concentrations up to 166 ng/L for DEET in surface water, and 54.3 ng/g dry weight (dw) for triclocarban in sediment. The dominant biocides were DEET and methylparaben, with their detection frequencies of 100% in both phases. An estimate of 152 t/y of 14 biocides was carried by the Yangtze River to the East China Sea. The distribution of biocides in the aquatic environments was significantly correlated to Gross Domestic Product (GDP), total phosphorus (TP) and total nitrogen (TN), suggesting dominant input sources from domestic wastewater of the cities along the river. Risk assessment showed high ecological risks posed by carbendazim in both phases and by triclosan in sediment. Therefore, proper measures should be taken to reduce the input of biocides into the river systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effective delivery of volatile biocides employing mesoporous silicates for treating biofilms

PubMed Central

Chan, Andrea C.; Townley, Helen E.

2017-01-01

Nanoparticulate delivery of biocides has the potential to decrease levels of exposure to non-target organisms, and miminize long-term exposure that can promote the development of resistance. Silica nanoparticles are an ideal vehicle since they are inert, biocompatible, biodegradable, and thermally and chemically stable. Encapsulation of biocides within nanoparticulates can improve their stability and longevity and maximize the biocidal potential of hydrophobic volatile compounds. Herein, we have shown that the plant secondary metabolites allyl isothiocyanate and cinnamaldehyde demonstrated increased antimicrobial activity against Escherichia coli in planktonic form, when packaged into mesoporous silica nanoparticles. Furthermore, the biocide-loaded nanoparticles showed activity against Pseudomonas aeruginosa biofilms that have inherent resistance to antimicrobial agents. The delivery platform can also be expanded to traditional biocides and other non-conventional antimicrobial agents. PMID:28077760

EU Regulation of Nanobiocides: Challenges in Implementing the Biocidal Product Regulation (BPR)

PubMed Central

Brinch, Anna; Hansen, Steffen Foss; Hartmann, Nanna B.; Baun, Anders

2016-01-01

The Biocidal Products Regulation (BPR) contains several provisions for nanomaterials (NMs) and is the first regulation in the European Union to require specific testing and risk assessment for the NM form of a biocidal substance as a part of the information requirements. Ecotoxicological data are one of the pillars of the information requirements in the BPR, but there are currently no standard test guidelines for the ecotoxicity testing of NMs. The overall objective of this work was to investigate the implications of the introduction of nano-specific testing requirements in the BPR and to explore how these might be fulfilled in the case of copper oxide nanoparticles. While there is information and data available in the open literature that could be used to fulfill the BPR information requirements, most of the studies do not take the Organisation for Economic Co-operation and Development’s nanospecific test guidelines into consideration. This makes it difficult for companies as well as regulators to fulfill the BPR information requirements for nanomaterials. In order to enable a nanospecific risk assessment, best practices need to be developed regarding stock suspension preparation and characterization, exposure suspensions preparation, and for conducting ecotoxicological test. PMID:28344290

EU Regulation of Nanobiocides: Challenges in Implementing the Biocidal Product Regulation (BPR).

PubMed

Brinch, Anna; Hansen, Steffen Foss; Hartmann, Nanna B; Baun, Anders

2016-02-16

The Biocidal Products Regulation (BPR) contains several provisions for nanomaterials (NMs) and is the first regulation in the European Union to require specific testing and risk assessment for the NM form of a biocidal substance as a part of the information requirements. Ecotoxicological data are one of the pillars of the information requirements in the BPR, but there are currently no standard test guidelines for the ecotoxicity testing of NMs. The overall objective of this work was to investigate the implications of the introduction of nano-specific testing requirements in the BPR and to explore how these might be fulfilled in the case of copper oxide nanoparticles. While there is information and data available in the open literature that could be used to fulfill the BPR information requirements, most of the studies do not take the Organisation for Economic Co-operation and Development's nanospecific test guidelines into consideration. This makes it difficult for companies as well as regulators to fulfill the BPR information requirements for nanomaterials. In order to enable a nanospecific risk assessment, best practices need to be developed regarding stock suspension preparation and characterization, exposure suspensions preparation, and for conducting ecotoxicological test.

Biocide Runoff from Building Facades: Degradation Kinetics in Soil.

PubMed

Bollmann, Ulla E; Fernández-Calviño, David; Brandt, Kristian K; Storgaard, Morten S; Sanderson, Hans; Bester, Kai

2017-04-04

Biocides are common additives in building materials. In-can and film preservatives in polymer-resin render and paint, as well as wood preservatives are used to protect facade materials from microbial spoilage. Biocides leach from the facade material with driving rain, leading to highly polluted runoff water (up to several mg L -1 biocides) being infiltrated into the soil surrounding houses. In the present study the degradation rates in soil of 11 biocides used for the protection of building materials were determined in laboratory microcosms. The results show that some biocides are degraded rapidly in soil (e.g., isothiazolinones: T 1/2 < 10 days) while others displayed higher persistence (e.g., terbutryn, triazoles: T 1/2 ≫ 120 days). In addition, mass balances of terbutryn and octylisothiazolinone were determined, including nine (terbutryn) and seven (octylisothiazolinone) degradation products, respectively. The terbutryn mass balance could be closed over the entire study period of 120 days and showed that relative persistent metabolites were formed, while the mass balances for octylisothiazolinone could not be closed. Octylisothiazolinone degradation products did not accumulate over time suggesting that the missing fraction was mineralized. Microtox-tests revealed that degradation products were less toxic toward the bacterium Aliivibrio fischeri than their parent compounds. Rain is mobilizing these biocides from the facades and transports them to the surrounding soils; thus, rainfall events control how often new input to the soil occurs. Time intervals between rainfall events in Northern Europe are shorter than degradation half-lives even for many rapidly degraded biocides. Consequently, residues of some biocides are likely to be continuously present due to repeated input and most biocides can be considered as "pseudo-persistent"-contaminants in this context. This was verified by (sub)urban soil screening, where concentrations of up to 0.1 μg g -1 were detected for parent compounds as well as terbutryn degradation products in soils below biocide treated facades.

Stimulatory effect of cooling tower biocides on amoebae.

PubMed

Srikanth, S; Berk, S G

1993-10-01

Two species of amoebae were isolated from the cooling tower of an air-conditioning system and examined for effects of exposure to four cooling tower biocides, a thiocarbamate compound, tributyltin neodecanoate mixed with quaternary ammonium compounds, another quaternary ammonium compound alone, and an isothiazolin derivative. The amoebae isolated were Acanthamoeba hatchetti and a Cochliopodium species. Two other amoeba cultures, an A. hatchetti culture and Cochliopodium bilimbosum, were obtained from the American Type Culture Collection (ATCC) and were also tested. The cooling tower isolates were more resistant to most of the biocides than the ATCC isolates were. The isothiazolin derivative was the least inhibitory to all four amoeba isolates, and tributyltin neodecanoate mixed with quaternary ammonium compounds was the most inhibitory to three of the four isolates. After exposure to lower concentrations of the biocides, including for one strain the manufacturer's recommended concentration of one biocide, the cooling tower amoeba populations increased significantly compared with unexposed controls, whereas the ATCC isolates were not stimulated at any of the concentrations tested. In some cases, concentrations which stimulated cooling tower amoebae inhibited the growth of the ATCC isolates. These results suggest that cooling tower amoebae may adapt to biocides, underscoring the need to use freshly isolated cooling tower organisms rather than organisms from culture collections for testing the efficacy of such biocides. The stimulatory effect of biocides on amoeba populations is an alarming observation, since these organisms may be reservoirs for legionellae. Biocides used to control microbial growth may actually enhance populations of host organisms for pathogenic bacteria.

Image Cytometric Analysis of Algal Spores for Evaluation of Antifouling Activities of Biocidal Agents.

PubMed

Il Koo, Bon; Lee, Yun-Soo; Seo, Mintae; Seok Choi, Hyung; Leng Seah, Geok; Nam, Taegu; Nam, Yoon Sung

2017-07-31

Chemical biocides have been widely used as marine antifouling agents, but their environmental toxicity impose regulatory restriction on their use. Although various surrogate antifouling biocides have been introduced, their comparative effectiveness has not been well investigated partly due to the difficulty of quantitative evaluation of their antifouling activity. Here we report an image cytometric method to quantitatively analyze the antifouling activities of seven commercial biocides using Ulva prolifera as a target organism, which is known to be a dominant marine species causing soft fouling. The number of spores settled on a substrate is determined through image analysis using the intrinsic fluorescence of chlorophylls in the spores. Pre-determined sets of size and shape of spores allow for the precise determination of the number of settled spores. The effects of biocide concentration and combination of different biocides on the spore settlement are examined. No significant morphological changes of Ulva spores are observed, but the amount of adhesive pad materials is appreciably decreased in the presence of biocides. It is revealed that the growth rate of Ulva is not directly correlated with the antifouling activities against the settlement of Ulva spores. This work suggests that image cytometric analysis is a very convenient, fast-processable method to directly analyze the antifouling effects of biocides and coating materials.

Sublethal Triclosan Exposure Decreases Susceptibility to Gentamicin and Other Aminoglycosides in Listeria monocytogenes▿

PubMed Central

Christensen, Ellen G.; Gram, Lone; Kastbjerg, Vicky G.

2011-01-01

The human food-borne pathogen Listeria monocytogenes is capable of persisting in food processing plants despite cleaning and sanitation and is likely exposed to sublethal biocide concentrations. This could potentially affect susceptibility of the bacterium to biocides and other antimicrobial agents. The purpose of the present study was to determine if sublethal biocide concentrations affected antibiotic susceptibility in L. monocytogenes. Exposure of L. monocytogenes strains EGD and N53-1 to sublethal concentrations of Incimaxx DES (containing peroxy acids and hydrogen peroxide) and Triquart Super (containing quaternary ammonium compound) in four consecutive cultures did not alter the frequency of antibiotic-tolerant isolates, as determined by plating on 2× the MIC for a range of antibiotics. Exposure of eight strains of L. monocytogenes to 1 and 4 μg/ml triclosan did not alter triclosan sensitivity. However, all eight strains became resistant to gentamicin (up to 16-fold increase in MIC) after exposure to sublethal triclosan concentrations. Gentamicin-resistant isolates of strains N53-1 and 4446 were also resistant to other aminoglycosides, such as kanamycin, streptomycin, and tobramycin. Gentamicin resistance remained at a high level also after five subcultures without triclosan or gentamicin. Aminoglycoside resistance can be caused by mutations in the target site, the 16S rRNA gene. However, such mutations were not detected in the N53-1-resistant isolates. A combination of gentamicin and ampicillin is commonly used in listeriosis treatment. The triclosan-induced resistance is, hence, of great concern. Further investigations are needed to determine the molecular mechanisms underlying the effect of triclosan. PMID:21746948

Research on Statistical Methodology Applicable to Technical Problems Associated with Navy Programs.

DTIC Science & Technology

1987-10-01

the fleetwide use of organotin antifouling paints that contain tributyltin ( TBT ), a tin-based compound, as a biocide. Organotin antifouling compounds...with this program has been devoted to providing technical and analytical support on various related statistical aspects. The TBT -release rate of a...paini ;q detrmined by placing a coated specimen panel or cylinder into a container of synthetic seawater, measuring the increasing concentration of TBT in

Biofilm Surface Density Determines Biocide Effectiveness

PubMed Central

Bas, Sara; Kramer, Mateja; Stopar, David

2017-01-01

High resistance of biofilms for chemical challenges is a serious industrial and medical problem. In this work a gradient of surface covered with biofilm has been produced and correlated to the effectiveness of different commercially available oxidative biocides. The results for thin Escherichia coli biofilms grown in rich media supplemented with glucose or lactose on glass or poly methyl methacrylate surfaces indicate that the effectiveness of hydrogen peroxide or chlorine dioxide and quaternary ammonium compounds is inversely proportional to the fraction of the surface covered with the biofilm. In areas where biofilm covered more than 90% of the available surface the biocide treatment was inefficient after 60 min of incubation. The combined effect of oxidant and surfactant increased the effectiveness of the biocide. On the other hand, the increased biofilm viscoelasticity reduced biocide effectiveness. The results emphasize differential biocide effectiveness depending on the fraction of the attached bacterial cells. The results suggest that biofilm biocide resistance is an acquired property that increases with biofilm maturation. The more dense sessile structures present lower log reductions compared to less dense ones. PMID:29276508

Method for Reduction of Silver Biocide Plating on Metal Surfaces

NASA Technical Reports Server (NTRS)

Steele, John; Nalette, Timothy; Beringer, Durwood

2013-01-01

Silver ions in aqueous solutions (0.05 to 1 ppm) are used for microbial control in water systems. The silver ions remain in solution when stored in plastic containers, but the concentration rapidly decreases to non-biocidal levels when stored in metal containers. The silver deposits onto the surface and is reduced to non-biocidal silver metal when it contacts less noble metal surfaces, including stainless steel, titanium, and nickel-based alloys. Five methods of treatment of contact metal surfaces to deter silver deposition and reduction are proposed: (1) High-temperature oxidation of the metal surface; (2) High-concentration silver solution pre-treatment; (3) Silver plating; (4) Teflon coat by vapor deposition (titanium only); and (5) A combination of methods (1) and (2), which proved to be the best method for the nickel-based alloy application. The mechanism associated with surface treatments (1), (2), and (5) is thought to be the development of a less active oxide layer that deters ionic silver deposition. Mechanism (3) is an attempt to develop an equilibrium ionic silver concentration via dissolution of metallic silver. Mechanism (4) provides a non-reactive barrier to deter ionic silver plating. Development testing has shown that ionic silver in aqueous solution was maintained at essentially the same level of addition (0.4 ppm) for up to 15 months with method (5) (a combination of methods (1) and (2)), before the test was discontinued for nickel-based alloys. Method (1) resulted in the maintenance of a biocidal level (approximately 0.05 ppm) for up to 10 months before that test was discontinued for nickel-based alloys. Methods (1) and (2) used separately were able to maintain ionic silver in aqueous solution at essentially the same level of addition (0.4 ppm) for up to 10 months before the test was discontinued for stainless steel alloys. Method (3) was only utilized for titanium alloys, and was successful at maintaining ionic silver in aqueous solution at essentially the same level of addition (0.4 ppm) for up to 10 months before the test was discontinued for simple flat geometries, but not for geometries that are difficult to Teflon coat.

Local viscosity and solvent relaxation experienced by rod-like fluorophores in AOT/4-chlorophenol/m-xylene organogels

NASA Astrophysics Data System (ADS)

Dandapat, Manika; Mandal, Debabrata

2017-01-01

Organogels prepared from AOT/4-chlorophenol/m-xylene are immobile in the macroscopic sense, with a well-characterized internal structure. However, the molecular level dynamics inside the gels is not too clear, although a very slow structural relaxation has been reported previously. Using a set of rod-like fluorophores, we find that the rotational mobility of a small guest molecule inside the gel can be extremely fast, indicating presence of sufficiently low-microviscosity domains. These domains consist of m-xylene solvent molecules trapped in the interstices of fiber bundles comprising columnar stacks of 4-chlorophenol surrounded by AOT molecules. However, interstitial trapping of m-xylene does retard its own dynamics, which explains the slow solvent relaxation inside the gels. Hence, the state of m-xylene in the organogel may be characterized as "bound", in contrast to the "free" state in neat m-xylene.

Evaluation of toxicity and genotoxicity of 2-chlorophenol on bacteria, fish and human cells.

PubMed

Vlastos, Dimitris; Antonopoulou, Maria; Konstantinou, Ioannis

2016-05-01

Due to the extensive use of chlorophenols (CPs) in anthropogenic activities, 2-Chlorophenol (2-CP), among other CPs, can enter aquatic ecosystems and can be harmful to a variety of organisms, including bacteria, fish and humans, that are exposed directly and/or indirectly to such contaminated environments. Based on the existing knowledge and in order to move a step forward, the purpose of this study is to investigate the toxic and mainly the genotoxic effects of 2-CP using a combination of bioassays. The tests include the marine bacterium Vibrio fischeri and micronuclei induction in the erythrocytes of Carassius auratus as well as in cultured human lymphocytes. The results obtained reveal that 2-CP is able to induce dose-dependent toxic and genotoxic effects on the selected tested concentrations under the specific experimental conditions. Copyright © 2016 Elsevier B.V. All rights reserved.

Flavanoid biocides: Wood preservatives based on condensed tannins

Treesearch

Peter Laks; Peggy A. McKaig; Richard W. Hemingway

1988-01-01

The condensed tannins are natural wood preservatives found in high concentrations in the bark and wood of some tree species. Condensed tannin-containing bark extracts from loblolly pine (Pinus taeda) were evaluated as wood preservatives using standard methods. Bark extracts by themselves did not cause any reduction in weight loss of pressure-treated...

Fatty acid-based formulations for wood protection against mold and sapstain

Treesearch

Carol A. Clausen; Robert D. Coleman; Vina W. Yang

2010-01-01

Safer, highly effective biocides providing long-term protection of mold growth on wood-based materials is of interest to the wood protection industry. Moldicide formulations containing synergistic combinations of ingredients derived from natural sources are commonly recognized as a promising approach for the next generation of wood protectants. Although fatty acid (FA...

NANOTECHNOLOGY: A NOVEL APPROACH TO PREVENT BIOCIDE LEACHING

EPA Science Inventory

This project will demonstrate the environmental benefits of introducing biocide into wood using hydrophobic nanoparticles as a delivery vehicle and controlled release device for organic and inorganic biocides. The primary benefits expected from use of nanoparticles as controll...

Biocides in hydraulic fracturing fluids: a critical review of their usage, mobility, degradation, and toxicity.

PubMed

Kahrilas, Genevieve A; Blotevogel, Jens; Stewart, Philip S; Borch, Thomas

2015-01-06

Biocides are critical components of hydraulic fracturing ("fracking") fluids used for unconventional shale gas development. Bacteria may cause bioclogging and inhibit gas extraction, produce toxic hydrogen sulfide, and induce corrosion leading to downhole equipment failure. The use of biocides such as glutaraldehyde and quaternary ammonium compounds has spurred a public concern and debate among regulators regarding the impact of inadvertent releases into the environment on ecosystem and human health. This work provides a critical review of the potential fate and toxicity of biocides used in hydraulic fracturing operations. We identified the following physicochemical and toxicological aspects as well as knowledge gaps that should be considered when selecting biocides: (1) uncharged species will dominate in the aqueous phase and be subject to degradation and transport whereas charged species will sorb to soils and be less bioavailable; (2) many biocides are short-lived or degradable through abiotic and biotic processes, but some may transform into more toxic or persistent compounds; (3) understanding of biocides' fate under downhole conditions (high pressure, temperature, and salt and organic matter concentrations) is limited; (4) several biocidal alternatives exist, but high cost, high energy demands, and/or formation of disinfection byproducts limits their use. This review may serve as a guide for environmental risk assessment and identification of microbial control strategies to help develop a sustainable path for managing hydraulic fracturing fluids.

Considerations on Directive 98/8 of the European Commission - the biocide directive.

PubMed

Patryn, Rafał; Jarosz, Mirosław J; Włoszczak-Szubzda, Anna; Sak, Jarosław; Pawlikowski, Jakub

2011-01-01

Nowadays, versatile human activity requires the development of technologies in the chemical and biological industries that ultimately enable an increase in human activity, and help create the living conditions in the domain of human civilization. Increasing this activity very frequently requires the implementation of new technologies concerning the active elimination of numerous threats and obstacles which are found in the human and natural environment. The concept of so-called biocidal products has been introduced into the European legislation as long as ten years ago, defining them as various types of 'chemical substances or microorganisms which can deter, render harmless, or exert a controlling eff ect on any harmful organism, by chemical or biological means'. They can be added to other materials (typically liquids) to protect them against biological infestation and growth. Biocidal products - due to their specificity, toxicity and composition - create a serious risk for human and animal life and health, as well as for the natural environment, it is therefore fully justified to have legal regulations concerning such biocides. Because biocidal products are intended to kill living organisms, and as such, many biocidal products pose a significant risk to human health and welfare, and have significant adverse eff ects on the natural environment. Great care is required when handling biocides and appropriate protective clothing and equipment should be used. Currently, Directive 98/8/EC is a comprehensive set of legal regulations concerning biocidal products, their specificity, principles relating to their placing on the market, and guidelines for their control. It is worth emphasizing that Directive 98/8/EC implements the clampdown on poisoning cases with biocides, the duty of which was passed to the so-called Centres of Consultation and Toxicological Information. These centres provide round-the-clock (24-hour) medical consultation and assistance in cases of poisonings with these products. The presented study constitutes an in-depth presentation and analysis of the European law concerning biocides and the current regulations applying to them.

Cold Incineration of Chlorophenols in Aqueous Solution by Advanced Electrochemical Process Electro-Fenton. Effect of Number and Position of Chlorine Atoms on the Degradation Kinetics

NASA Astrophysics Data System (ADS)

Oturan, Nihal; Panizza, Marco; Oturan, Mehmet A.

2009-09-01

This study reports the kinetics of the degradation of several chlorophenols (CPs), such as monochlorophenols (2-chlorophenol and 4-chlorophenol), dichlorophenols (2,4-dichlorophenol and 2,6- dichlorophenol), trichlorophenols (2,3,5- trichlorophenol and 2,4,5-trichlorophenol), 2,3,5,6-tetrachlorophenol, and pentachlorophenol, by the electro-Fenton process using a carbon felt cathode and a Pt anode. The effect of number and the position of the chlorine atoms in the aromatic ring on the oxidative degradation rate was evaluated and discussed. The oxidation reaction of all the CPs with hydroxyl radicals evidenced a pseudo-first-order kinetics and the rate constant decreased with increasing the number of chlorine atoms. The absolute rate constant of second-order reaction kinetics between CPs and •OH was determined by the competition kinetics method in the range of (3.56-7.75) × 109 M-1 s-1 and follows the same sequence of the apparent rate constants. The mineralization of several CPs and of a mixture of all CPs under study was monitored by the total organic carbon (TOC) removal and the chlorine release during mineralization was followed by ion chromatography. Our results demonstrated that more chlorinated phenols are more difficult to mineralize; however for all the tested CPs, almost quantitative release of chloride ions was obtained after 6 h of treatment.

Oxidative degradation of phenols in sono-Fenton-like systems upon high-frequency ultrasound irradiation

NASA Astrophysics Data System (ADS)

Aseev, D. G.; Sizykh, M. R.; Batoeva, A. A.

2017-12-01

The kinetics of oxidative degradation of phenol and chlorophenols upon acoustic cavitation in the megahertz range (1.7 MHz) is studied experimentally in model systems, and the involvement of in situ generated reactive oxygen species (ROSs) is demonstrated. The phenols subjected to high frequency ultrasound (HFUS) are ranked in terms of their rate of conversion: 2,4,6-trichlorophenol > 2,4-dichlorophenol 2-chlorophenol > 4-chlorophenol phenol. Oxidative degradation upon HFUS irradiation is most efficient at low concentrations of pollutants, due to the low steady-state concentrations of the in situ generated ROSs. A dramatic increase is observed in the efficiency of oxidation in several sonochemical oxidative systems (HFUS in combination with other chemical oxidative factors). The system with added Fe2+ (a sono-Fenton system) derives its efficiency from hydrogen peroxide generated in situ as a result of the recombination of OH radicals. The S2O8 2-/Fe2+/HFUS system has a synergetic effect on substrate oxidation that is attributed to a radical chain mechanism. In terms of the oxidation rates, degrees of conversion, and specific energy efficiencies of 4-chlorophenol oxidation based on the amount of oxidized substance per unit of expended energy the considered sonochemical oxidative systems form the series HFUS < S2O8 2-/HFUS < S2O8 2-/Fe2+/HFUS.

Degradation of Chlorophenols by Alcaligenes eutrophus JMP134(pJP4) in Bleached Kraft Mill Effluent

PubMed Central

Valenzuela, J.; Bumann, U.; Cespedes, R.; Padilla, L.; Gonzalez, B.

1997-01-01

The ability of Alcaligenes eutrophus JMP134(pJP4) to degrade 2,4-dichlorophenoxyacetic acid, 2,4,6-trichlorophenol, and other chlorophenols in a bleached kraft mill effluent was studied. The efficiency of degradation and the survival of strain JMP134 and indigenous microorganisms in short-term batch or long-term semicontinuous incubations performed in microcosms were assessed. After 6 days of incubation, 2,4-dichlorophenoxyacetate (400 ppm) or 2,4,6-trichlorophenol (40 to 100 ppm) were extensively degraded (70 to 100%). In short-term batch incubations, indigenous microorganisms were unable to degrade such of compounds. Degradation of 2,4,6-trichlorophenol by strain JMP134 was significantly lower at 200 to 400 ppm of compound. This strain was also able to degrade 2,4-dichlorophenoxyacetate, 2,4,6-trichlorophenol, 4-chlorophenol, and 2,4,5-trichlorophenol when bleached Kraft mill effluent was amended with mixtures of these compounds. On the other hand, the chlorophenol concentration and the indigenous microorganisms inhibited the growth and survival of the strain in short-term incubations. In long-term (>1-month) incubations, strain JMP134 was unable to maintain a large, stable population, although extensive 2,4,6-trichlorophenol degradation was still observed. The latter is probably due to acclimation of the indigenous microorganisms to degrade 2,4,6-trichlorophenol. Acclimation was observed only in long-term, semicontinuous microcosms. PMID:16535488

Phenoxy herbicides and chlorophenols: a case control study on soft tissue sarcoma and malignant lymphoma.

PubMed Central

Smith, J. G.; Christophers, A. J.

1992-01-01

A case control study on patients with soft tissue sarcoma and malignant lymphoma was undertaken to test whether there was any association between these diseases and past exposure to chlorinated phenoxy acid herbicides or chlorophenols. It was carried out over the period 1982-1988 in Victoria, Australia. Thirty males with soft tissue sarcoma and 52 males with malignant lymphoma were matched by age, place of residence and sex with one population control and one cancer control each. Exposure was assessed by personal interviews conducted by an occupational hygienist. Exposures within 5 years prior to diagnosis of each matched case were ignored, both for the cases and their matched controls. The estimated relative risks for definite or probable exposure to chlorinated phenoxy compounds or chlorophenols for at least 1 day were 1.0 (95% confidence interval (CI): 0.3-3.1) for soft tissue sarcoma and 1.5 (95% CI: 0.6-3.7) for malignant lymphoma. When the criterion for exposure was raised to more than 30 days, the estimated relative risks were 2.0 (95% CI: 0.5-8.0) for soft tissue sarcoma and 2.7 (95% CI: 0.7-9.6) for malignant lymphoma. Additional analyses were carried out for exposure of at least 1 day to phenoxy herbicides alone or chlorophenols alone. None of the estimated relative risks was significantly greater than unity. PMID:1558802

Biocidal packaging for pharmaceuticals, foods, and other perishables.

PubMed

Larson, Alyssa M; Klibanov, Alexander M

2013-01-01

Many consumer goods must be protected from bacterial and fungal colonization to ensure their integrity and safety. By making these items' packaging biocidal, the interior environment can be preserved from microbial spoilage without altering the products themselves. Herein we briefly review this concept, referred to as active packaging, and discuss existing methods for constructing active packaging systems. They are based on either packaging materials that release biocides or those that are themselves intrinsically biocidal (or biostatic), with numerous variations within each category.

Combined treatments of enterocin AS-48 with biocides to improve the inactivation of methicillin-sensitive and methicillin-resistant Staphylococcus aureus planktonic and sessile cells.

PubMed

Caballero Gómez, Natacha; Abriouel, Hikmate; Grande, M José; Pérez Pulido, Rubén; Gálvez, Antonio

2013-05-15

Control of staphylococci during cleaning and disinfection is important to the food industry. Broad-spectrum bacteriocins with proved anti-staphylococcal activity, such as enterocin AS-48, could open new possibilities for disinfection in combination with biocides. In the present study, enterocin AS-48 was tested singly or in combination with biocides against a cocktail of six Staphylococcus aureus strains (including three methicillin-resistant strains) in planktonic state as well as in biofilms formed on polystyrene microtiter plates. Cells were challenged with enterocin, biocides or enterocin/biocide combinations. Inactivation of planktonic cells increased significantly (p<0.05) when enterocin AS-48 (25mg/l) was tested in combination with benzalkonium chloride (BC), cetrimide (CT) and hexadecylpyridinium chloride (HDP), and non-significantly in combination with didecyldimethylammonium bromide (AB), triclosan (TC), hexachlorophene (CF), polyhexamethylen guanidinium chloride (PHMG), chlorhexidine (CH) or P3-oxonia (OX). In the sessile state (24h biofilms), staphylococci required higher biocide concentrations in most cases, except for OX. Inactivation of sessile staphylococci increased remarkably when biocides were applied in combination with enterocin AS-48, especially when the bacteriocin was added at 50mg/l. During storage, the concentrations of sessile as well as planktonic cells in the treated samples decreased remarkably for BC, TC and PHMG, but OX failed to inhibit proliferation of the treated biofilms as well as growth of planktonic cells. The observed inhibitory effects during storage were potentiated when the biocides were combined with 50 mg/l enterocin AS-48. Results from this study suggest that selected combinations of enterocin AS-48 and biocides offer potential use against planktonic and sessile, methicillin-sensitive and methicillin-resistant S. aureus. Copyright © 2013 Elsevier B.V. All rights reserved.

Assessment of Silver Based Disinfection Technology for CEV and Future US Spacecraft

NASA Technical Reports Server (NTRS)

Callahan, Michael R.; Adam, Niklas M.; Roberts, Michael S.; Garland, Jay L.; Sager, John C.; Pickering, Karen D.

2007-01-01

Silver biocide offers a potential advantage over iodine, the current state-of-the-art in US spacecraft disinfection technology, in that silver can be safely consumed by the crew. As such, silver may reduce the overall complexity and mass of future spacecraft potable water systems, particularly those used to support long duration missions. A primary technology gap identified for the use of silver biocide is one of material compatibility. Wetted materials of construction are required to be selected such that silver ion concentrations can be maintained at biocidally effective levels. Preliminary data on silver biocide depletion rates in heritage spacecraft potable water system wetted-materials of construction has been gathered as part of a multi-phase test project aimed at the characterization of silver based biocide technology through: development of preferred materials lists, investigation of silver biocide forms and delivery methods, down-selection of silver biocide technologies, and integrated testing. A 10% - 20% loss in silver ion concentration per day was observed for acid passivated Nitronic 40 tubing with surface area to volume (S/V) ratios of approximately 4.59 cm-1. The Nitronic 40 tubes were tested both with and without biocide pretreatment. Silver biocide depletion was also observed at approximately 0.1% per day for the first 35 days of exposure to acid passivated Inconel 718 coupon, S/V of approximately 0.14 cm-1. Surface analysis by scanning election microscopy (SEM) suggested deposition of silver metal on both test materials. SEM analysis also provided evidence of potential variability in the passivation process for tube configuration of the Nitronic 40 test apparatus. These preliminary results are presented and discussed herein, along with the current project status.

Biocides in hydraulic fracturing: A comparison to agricultural and assessment of hazard and vulnerability with respect to groundwater pollution

NASA Astrophysics Data System (ADS)

Worrall, Fred; Wilson, Miles; Davies, Richard

2017-04-01

Biocides are one possible chemical additive to frack fluids and their role is to control bacterial growth. Since biocides are designed to be toxic to particular organisms, their accidental or deliberate release into the environment has become a growing topic of concern, especially with regards to fracking. The objective of this study was to consider whether biocides proposed for use in fracking, could be a threat to English groundwater based on past groundwater monitoring data. The study considered all groundwater samples analysed for biocides in English groundwater between 2005 and 2014. The monitoring records were compared to: records of application (both amount and area); and chemical and molecular data for the biocides. The study did not use traditional adsorption and degradation data as these parameters are prone to variability and are not pure molecular parameters. The study showed that of the 110 biocides tested for in English groundwaters in the decade 2005 - 2014. The total number of detections was 2234 out of 1475000 observations of 95 compounds, and 38 were compounds that were not applied during the period of record. The detection of these 38 compounds did not decline over the 10 year period implying very long residence times and that once compounds do pollute an aquifer, then they will be a persistent problem. The study was able to develop binomial regression models of the probability of detecting pesticide in groundwater based upon molecular and application variables; and solely upon molecular properties. The solubility of the range of biocides used in frack fluids would imply a potentially higher hazard than for most agricultural biocides, but molecular modelling implied that one compound could be safer than others.

Successful aerobic bioremediation of groundwater contaminated with higher chlorinated phenols by indigenous degrader bacteria.

PubMed

Mikkonen, Anu; Yläranta, Kati; Tiirola, Marja; Dutra, Lara Ambrosio Leal; Salmi, Pauliina; Romantschuk, Martin; Copley, Shelley; Ikäheimo, Jukka; Sinkkonen, Aki

2018-07-01

The xenobiotic priority pollutant pentachlorophenol has been used as a timber preservative in a polychlorophenol bulk synthesis product containing also tetrachlorophenol and trichlorophenol. Highly soluble chlorophenol salts have leaked into groundwater, causing severe contamination of large aquifers. Natural attenuation of higher-chlorinated phenols (HCPs: pentachlorophenol + tetrachlorophenol) at historically polluted sites has been inefficient, but a 4-year full scale in situ biostimulation of a chlorophenol-contaminated aquifer by circulation and re-infiltration of aerated groundwater was remarkably successful: pentachlorophenol decreased from 400 μg L -1 to <1 μg L -1 and tetrachlorophenols from 4000 μg L -1 to <10 μg L -1 . The pcpB gene, the gene encoding pentachlorophenol hydroxylase - the first and rate-limiting enzyme in the only fully characterised aerobic HCP degradation pathway - was present in up to 10% of the indigenous bacteria already 4 months after the start of aeration. The novel quantitative PCR assay detected the pcpB gene in situ also in the chlorophenol plume of another historically polluted aquifer with no remediation history. Hotspot groundwater HCPs from this site were degraded efficiently during a 3-week microcosm incubation with one-time aeration but no other additives: from 5400 μg L -1 to 1200 μg L -1 and to 200 μg L -1 in lightly and fully aerated microcosms, respectively, coupled with up to 2400% enrichment of the pcpB gene. Accumulation of lower-chlorinated metabolites was observed in neither in situ remediation nor microcosms, supporting the assumption that HCP removal was due to the aerobic degradation pathway where the first step limits the mineralisation rate. Our results demonstrate that bacteria capable of aerobic mineralisation of xenobiotic pentachlorophenol and tetrachlorophenol can be present at long-term polluted groundwater sites, making bioremediation by simple aeration a viable and economically attractive alternative. Copyright © 2018 Elsevier Ltd. All rights reserved.

The Effect of Long-Term Storage on the Physiochemical and Bactericidal Properties of Electrochemically Activated Solutions

PubMed Central

Robinson, Gareth; Thorn, Robin; Reynolds, Darren

2013-01-01

Electrochemically activated solutions (ECAS) are generated by electrolysis of NaCl solutions, and demonstrate broad spectrum antimicrobial activity and high environmental compatibility. The biocidal efficacy of ECAS at the point of production is widely reported in the literature, as are its credentials as a “green biocide.” Acidic ECAS are considered most effective as biocides at the point of production and ill suited for extended storage. Acidic ECAS samples were stored at 4 °C and 20 °C in glass and polystyrene containers for 398 days, and tested for free chlorine, pH, ORP and bactericidal activity throughout. ORP and free chlorine (mg/L) in stored ECAS declined over time, declining at the fastest rate when stored at 20 °C in polystyrene and at the slowest rate when stored at 4 °C in glass. Bactericidal efficacy was also affected by storage and ECAS failed to produce a 5 log10 reduction on five occasions when stored at 20 °C. pH remained stable throughout the storage period. This study represents the longest storage evaluation of the physiochemical parameters and bactericidal efficacy of acidic ECAS within the published literature and reveals that acidic ECAS retain useful bactericidal activity for in excess of 12 months, widening potential applications. PMID:23263673

The effect of long-term storage on the physiochemical and bactericidal properties of electrochemically activated solutions.

PubMed

Robinson, Gareth; Thorn, Robin; Reynolds, Darren

2012-12-24

Electrochemically activated solutions (ECAS) are generated by electrolysis of NaCl solutions, and demonstrate broad spectrum antimicrobial activity and high environmental compatibility. The biocidal efficacy of ECAS at the point of production is widely reported in the literature, as are its credentials as a "green biocide." Acidic ECAS are considered most effective as biocides at the point of production and ill suited for extended storage. Acidic ECAS samples were stored at 4 °C and 20 °C in glass and polystyrene containers for 398 days, and tested for free chlorine, pH, ORP and bactericidal activity throughout. ORP and free chlorine (mg/L) in stored ECAS declined over time, declining at the fastest rate when stored at 20 °C in polystyrene and at the slowest rate when stored at 4 °C in glass. Bactericidal efficacy was also affected by storage and ECAS failed to produce a 5 log(10) reduction on five occasions when stored at 20 °C. pH remained stable throughout the storage period. This study represents the longest storage evaluation of the physiochemical parameters and bactericidal efficacy of acidic ECAS within the published literature and reveals that acidic ECAS retain useful bactericidal activity for in excess of 12 months, widening potential applications.

Chemistry of Durable and Regenerable Biocidal Textiles

ERIC Educational Resources Information Center

Gang Sun; Worley, S. Dave

2005-01-01

Antimicrobial textiles can be categorized into two groups, biocidal and biostatic materials, according to their functions. Biostatic functions refer to inhibiting growth of microorganisms on textiles and preventing the materials from biodegradation and biocidal materials are able to kill microorganisms, thus eliminating their growth, sterilizing…

¹H-MAS-NMR chemical shifts in hydrogen-bonded complexes of chlorophenols (pentachlorophenol, 2,4,6-trichlorophenol, 2,6-dichlorophenol, 3,5-dichlorophenol, and p-chlorophenol) and amine, and H/D isotope effects on ¹H-MAS-NMR spectra.

PubMed

Honda, Hisashi

2013-04-22

Chemical shifts (CS) of the ¹H nucleus in N···H···O type hydrogen bonds (H-bond) were observed in some complexes between chlorophenols [pentachlorophenol (PCP), 2,4,6-tricholorophenol (TCP), 2,6-dichlorophenol (26DCP), 3,5-dichlorophenol (35DCP), and p-chlorophenol (pCP)] and nitrogen-base (N-Base) by solid-state high-resolution ¹H-NMR with the magic-angle-spinning (MAS) method. Employing N-Bases with a wide range of pKa values (0.65-10.75), ¹H-MAS-NMR CS values of bridging H atoms in H-bonds were obtained as a function of the N-Base's pKa. The result showed that the CS values were increased with increasing pKa values in a range of DpKa < 0 [DpKa = pKa(N-Base)-pKa(chlorophenols)] and decreased when DpKa > 2: The maximum CS values was recorded in the PCP (pKa = 5.26)-4-methylpyridine (6.03), TCP (6.59)-imidazole (6.99), 26DCP (7.02)-2-amino-4-methylpyridine (7.38), 35DCP (8.04)-4-dimethylaminopyridine (9.61), and pCP (9.47)-4-dimethylaminopyridine (9.61) complexes. The largest CS value of 18.6 ppm was recorded in TCP-imidazole crystals. In addition, H/D isotope effects on ¹H-MAS-NMR spectra were observed in PCP-2-amino-3-methylpyridine. Based on the results of CS simulation using a B3LYP/6-311+G** function, it can be explained that a little changes of the N-H length in H-bond contribute to the H/D isotope shift of the ¹H-MAS-NMR peaks.

Development of a novel ultrasound-assisted headspace liquid-phase microextraction and its application to the analysis of chlorophenols in real aqueous samples.

PubMed

Xu, Hui; Liao, Ying; Yao, Jinrong

2007-10-05

A new sample pretreatment technique, ultrasound-assisted headspace liquid-phase microextraction was developed as mentioned in this paper. In the technique, the volatile analytes were headspace extracted into a small drop of solvent, which suspended on the bottom of a cone-shaped PCR tube instead of the needle tip of a microsyringe. More solvent could be suspended in the PCR tube than microsyringe due to the larger interfacial tension, thus the analysis sensitivity was significantly improved with the increase of the extractant volume. Moreover, ultrasound-assisted extraction and independent controlling temperature of the extractant and the sample were performed to enhance the extraction efficiency. Following the extraction, the solvent-loaded sample was analyzed by high-performance liquid chromatography. Chlorophenols (2-chlorophenol, 2,4-dichlorophenol and 2,6-dichlorophenol) were chosen as model analytes to investigate the feasibility of the method. The experimental conditions related to the extraction efficiency were systematically studied. Under the optimum experimental conditions, the detection limit (S/N=3), intra- and inter-day RSD were 6 ng mL(-1), 4.6%, 3.9% for 2-chlorophenol, 12 ng mL(-1), 2.4%, 8.8% for 2,4-dichlorophenol and 23 ng mL(-1), 3.3%, 5.3% for 2,6-dichlorophenol, respectively. The proposed method was successfully applied to determine chlorophenols in real aqueous samples. Good recoveries ranging from 84.6% to 100.7% were obtained. In addition, the extraction efficiency of our method and the conventional headspace liquid-phase microextraction were compared; the extraction efficiency of the former was about 21 times higher than that of the latter. The results demonstrated that the proposed method is a promising sample pretreatment approach, its advantages over the conventional headspace liquid-phase microextraction include simple setup, ease of operation, rapidness, sensitivity, precision and no cross-contamination. The method is very suitable for the analysis of trace volatile and semivolatile pollutants in real aqueous sample.

Modeling of facade leaching in urban catchments

NASA Astrophysics Data System (ADS)

Coutu, S.; Del Giudice, D.; Rossi, L.; Barry, D. A.

2012-12-01

Building facades are protected from microbial attack by incorporation of biocides within them. Flow over facades leaches these biocides and transports them to the urban environment. A parsimonious water quantity/quality model applicable for engineered urban watersheds was developed to compute biocide release from facades and their transport at the urban basin scale. The model couples two lumped submodels applicable at the basin scale, and a local model of biocide leaching at the facade scale. For the facade leaching, an existing model applicable at the individual wall scale was utilized. The two lumped models describe urban hydrodynamics and leachate transport. The integrated model allows prediction of biocide concentrations in urban rivers. It was applied to a 15 km2urban hydrosystem in western Switzerland, the Vuachère river basin, to study three facade biocides (terbutryn, carbendazim, diuron). The water quality simulated by the model matched well most of the pollutographs at the outlet of the Vuachère watershed. The model was then used to estimate possible ecotoxicological impacts of facade leachates. To this end, exceedance probabilities and cumulative pollutant loads from the catchment were estimated. Results showed that the considered biocides rarely exceeded the relevant predicted no-effect concentrations for the riverine system. Despite the heterogeneities and complexity of (engineered) urban catchments, the model application demonstrated that a computationally "light" model can be employed to simulate the hydrograph and pollutograph response within them. It thus allows catchment-scale assessment of the potential ecotoxicological impact of biocides on receiving waters.

Nanotechnology : implications for the wood preservation industry

Treesearch

Carol A. Clausen

2007-01-01

Nanotechnology has the potential to greatly impact the wood protection industry through the creation of nanomaterials with unique properties. Nanobiocides may find applications as co-biocides, or may alter treatability properties such as penetration and biocide distribution. Nanocarrier delivery systems may increase the applications for organic biocides through...

The environmental behaviour of polychlorinated phenols and its relevance to cork forest ecosystems: a review.

PubMed

McLellan, Iain; Carvalho, Mariana; Silva Pereira, Cristina; Hursthouse, Andrew; Morrison, Calum; Tatner, Paul; Martins, Isabel; San Romão, M Vitória; Leitão, Maria

2007-10-01

Pentachlorophenol (PCP) has been used as a herbicide, biocide and preservative worldwide since the 1930s and as a result, extensive and prolonged contamination exists. The environmental impact increases when its many degradation products are taken into consideration. A number of chloroanisols and their related chlorophenols have been found in cork slabs collected from Portuguese oak tree forests before stopper manufacturing, and contamination by PCP and polychlorinated anisole (PCA) has been detected in Canadian forests. It is suggested that the use of polychlorinated phenols, in particular PCP, is thought to be a cause of the cork taint problem in wine, a major socio-economic impact not only for industry but on sensitive and highly biodiverse ecosystems. It also highlights particular issues relating to the regional regulation of potentially toxic chemicals and global economics world wide. To fully understand the impact of contamination sources, the mechanisms responsible for the fate and transport of PCP and its degradation products and assessment of their environmental behaviour is required. This review looks at the current state of knowledge of soil sorption, fate and bioavailability and identifies the challenges of degradation product identification and the contradictory evidence from field and laboratory observations. The need for a systematic evaluation of PCP contamination in relation to cork forest ecosystems and transfer of PCP between trophic levels is emphasised by discrepancies in bioaccumulation and toxicity. This is essential to enable long term management of not only transboundary contaminants, but also the sustainable management of socially and economically important forest ecosystems.

Human Health Risk of Ingested Nanoparticles That Are Added as Multifunctional Agents to Paints: an In Vitro Study

PubMed Central

Kaiser, Jean-Pierre; Roesslein, Matthias; Diener, Liliane; Wick, Peter

2013-01-01

Microorganisms growing on painted surfaces are not only an aesthetic problem, but also actively contribute to the weathering and deterioration of materials. A widely used strategy to combat microbial colonization is the addition of biocides to the paint. However, ecotoxic, non-degradable biocides with a broad protection range are now prohibited in Europe, so the paint industry is considering engineered nanoparticles (ENPs) as an alternative biocide. There is concern that ENPs in paint might be released in run-off water and subsequently consumed by animals and/or humans, potentially coming into contact with cells of the gastrointestinal tract and affecting the immune system. Therefore, in the present study we evaluated the cytotoxic effects of three ENPs (nanosilver, nanotitanium dioxide and nanosilicon dioxide) that have a realistic potential for use in paints in the near future. When exposed to nanotitanium dioxide and nanosilicon dioxide in concentrations up to 243 µg/mL for 48 h, neither the gastrointestinal cells (CaCo-2) nor immune system cells (Jurkat) were significantly affected. However, when exposed to nanosilver, several cell parameters were affected, but far less than by silver ions used as a control. No differences in cytotoxicity were observed when cells were exposed to ENP-containing paint particles, compared with the same paint particles without ENPs. Paint particles containing ENPs did not affect cell morphology, the release of reactive oxygen species or cytokines, cell activity or cell death in a different manner to the same paint particles without ENPs. The results suggest that paints doped with ENPs do not pose an additional acute health hazard for humans. PMID:24358264

Long-term biobarriers to plant and animal intrusions of uranium tailings. [24% trifluralin, 18% carbon black, and 58% polymer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cline, J.F.; Burton, F.G.; Cataldo, D.A.

1982-09-01

The objective of this project was to develop and evaluate the effectiveness of physical and chemical barriers designed to prevent plant and animal breachment of uranium mill tailings containment systems for an extended period of time. A polymeric carrier/biocide delivery system was developed and tested in the laboratory, greenhouse and field. A continuous flow technique was established to determine the release rates of the biocides from the PCD systems; polymeric carrier specifications were established. Studies were conducted to determine effective biocide concentrations required to produce a phytotoxic response and the relative rates of phytotoxin degradation resulting from chemical and biologicalmore » breakdown in soils. The final PCD system developed was a pelletized system containing 24% trifluralin, 18% carbon black and 58% polymer. Pellets were placed in the soil at the Grand Junction U-tailings site at one in. and two in. intervals. Data obtained in the field determined that the pellets released enough herbicide to the soil layer to stop root elongation past the barrier. Physical barriers to subsurface movement of burrowing animals were investigated. Small crushed stone (1 to 1 1/2 in. diameter) placed over asphalt emulsion and multilayer soil seals proved effective as barriers to a small mammal (ground squirrels) but were not of sufficient size to stop a larger animal (the prairie dog). No penetrations were made through the asphalt emulsion or the clay layer of the multilayer soil seals by either of the two mammals tested. A literature survey was prepared and published on the burrowing habits of the animals that may be found at U-tailings sites.« less

Performance of copper-based wood preservatives in soil bed exposures

Treesearch

Stan T. Lebow; Thomas Nilsson; Jeffrey J. Morrell

Copper-based biocides are widely used to protect wood from biological attack in a variety of environments. Chromated copper arsenate (CCA) is the dominant copper-based preservative for wood protection (J. T. MICKLEWRIGHT, 1989). First developed in India in the 1930s, CCA contains a very effective combination of materials. Copper provides protection against most...

76 FR 11980 - Stakeholder Input: Listening Session to Provide Information and Solicit Suggestions for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-04

... organisms to the surrounding water. Coatings used to deter organism growth on vessel hulls can release heavy metals and/or other biocides, which can lead to acute or chronic toxicity in non-targeted organisms. Bilgewater can contain oils, dissolved heavy metals, and other chemical constituents that can result in toxic...

Removing 3,5-Dichlorophenol from Wastewater by Alternative Adsorbents

NASA Astrophysics Data System (ADS)

Kobetičová, Hana; Galbičková, Blanka; Ševčíková, Janka; Soldán, Maroš

2014-12-01

The main objective of this paper is to evaluate an efficiency of 3,5 - dichlorophenol removal from wastewater by using alternative adsorbents. Chlorophenols are organic compounds consisting of a benzene ring, OH groups and also atoms of chlorine. Chlorophenols may have a huge isomere variety that means there are differences in their chemical and physical properties. Due to their toxicity it is necessary to remove them from waste water and in this paper an alternative way of such process is described.

Biocidal Energetic Materials for the Destruction of Spore Forming Bacteria

DTIC Science & Technology

2015-07-01

Bacteria Spore Gas Antibacterial Thermal Unclassified Unclassified Unclassified SAR 47 Suhithi Peiris...naturally antibacterial and biocidal properties using combustion synthesis of mildly energetic reactants; and, (2) engineering an aerosolized spray...of biocidal gases using unique a deflagration synthesis approach. Accomplishments for all years: Major Activity 1: Creating highly porous

Analysis of metal and biocides resistance genes in drug resistance and susceptible Salmonella enterica from food animals

USDA-ARS?s Scientific Manuscript database

Background Generally drug resistant bacteria carry antibiotic resistance genes and heavy metal and biocide resistance genes on large conjugative plasmids. The presence of these metal and biocide resistance genes in susceptible bacteria are not assessed comprehensively. Hence, WGS data of susceptib...

SOLUBILITY OF ORGANIC BIOCIDES IN SUPERCRITICAL CO2 AND CO2+ COSOLVENT MIXTURES

EPA Science Inventory

Solubilities of four organic biocides in supercritical carbon dioxide (Sc-CO2) were measured using a dynamic flowr apparatus over a pressure range of 10 to 30 MPa and temperature of 35-80 degrees C. The biocides studied were: Amical-48 (diiodomethyl p-tolyl sulfone), chlorothalo...

Formulation of Biocides Increases Antimicrobial Potency and Mitigates the Enrichment of Nonsusceptible Bacteria in Multispecies Biofilms

PubMed Central

Forbes, Sarah; Cowley, Nicola; Mistry, Hitesh; Amézquita, Alejandro

2017-01-01

ABSTRACT The current investigation aimed to generate data to inform the development of risk assessments of biocide usage. Stabilized domestic drain biofilm microcosms were exposed daily over 6 months to increasing concentrations (0.01% to 1%) of the biocide benzalkonium chloride (BAC) in a simple aqueous solution (BAC-s) or in a complex formulation (BAC-f) representative of a domestic cleaning agent. Biofilms were analyzed by culture, differentiating by bacterial functional group and by BAC or antibiotic susceptibility. Bacterial isolates were identified by 16S rRNA sequencing, and changes in biofilm composition were assessed by high-throughput sequencing. Exposure to BAC-f resulted in significantly larger reductions in levels of viable bacteria than exposure to BAC-s, while bacterial diversity greatly decreased during exposure to both BAC-s and BAC-f, as evidenced by sequencing and viable counts. Increases in the abundance of bacteria exhibiting reduced antibiotic or BAC susceptibility following exposure to BAC at 0.1% were significantly greater for BAC-s than BAC-f. Bacteria with reduced BAC and antibiotic susceptibility were generally suppressed by higher BAC concentrations, and formulation significantly enhanced this effect. Significant decreases in the antimicrobial susceptibility of bacteria isolated from the systems before and after long-term BAC exposure were not detected. In summary, dose-dependent suppression of bacterial viability by BAC was enhanced by formulation. Biocide exposure decreased bacterial diversity and transiently enriched populations of organisms with lower antimicrobial susceptibility, and the effects were subsequently suppressed by exposure to 1% BAC-f, the concentration most closely reflecting deployment in formulated products. IMPORTANCE Assessment of the risks of biocide use has been based mainly on the exposure of axenic cultures of bacteria to biocides in simple aqueous solutions. The current investigation aimed to assess the effects of formulation on the outcome of biocide exposure in multispecies biofilms. Formulation of the cationic biocide BAC significantly increased antimicrobial potency. Bacteria with lower antimicrobial susceptibility whose populations were enriched after low-level biocide exposure were more effectively suppressed by the biocide at in-use concentrations (1% [wt/vol]) in a formulation than in a simple aqueous solution. These observations underline the importance of simulating normal deployment conditions in considering the risks and benefits of biocide use. PMID:28115386

Chlorophenol degradation in soil columns inoculated with Anthracophyllum discolor immobilized on wheat grains.

PubMed

Diez, M C; Gallardo, F; Tortella, G; Rubilar, O; Navia, R; Bornhardt, C

2012-03-01

The white-rot fungus Anthracophyllum discolor immobilized on wheat grains was evaluated for chlorophenol (2,4-dichlorophenol, 2,4,6-trichlorophenol and pentachlorophenol) degradation in allophanic soil columns activated by acidification. Columns without inoculation were used as the control to evaluate the adsorption capacity of the soil columns. The chlorophenols were removed efficiently in soil columns by both adsorption and degradation processes. In inoculated soil columns, 2,4-dichlorophenol was highly degraded and this degradation is associated with a high production of manganese peroxidase. 2,4,6-trichlorophenol was degraded to a lesser extent compared with 2,4-dichlorophenol. Pentachlorophenol was first removed by adsorption and then through degradation by the fungus. Manganese peroxidase activity was lowest when the column was fed with pentachlorophenol and highest when the column was fed with 2,4-dichlorophenol. Laccase was also produced by the fungus but to a lesser degree. Copyright © 2010 Elsevier Ltd. All rights reserved.

Electrocatalytic behaviour of surface confined pentanethio cobalt (II) binuclear phthalocyanines towards the oxidation of 4-chlorophenol

NASA Astrophysics Data System (ADS)

Makinde, Zainab O.; Louzada, Marcel; Mashazi, Philani; Nyokong, Tebello; Khene, Samson

2017-12-01

Cobalt binuclear phthalocyanine (CoBiPc) bearing pentanethio substituents at the peripheral positions were synthesized. The immobilization of the synthesized cobalt phthalocyanines on gold electrode was achieved using self-assembled monolayer method (SAM). X-ray photoelectron spectroscopy (XPS) and Kelvin Probe (KP) techniques were used to characterise the formation of monomeric and binuclear phthalocyanine SAMs on the gold surface. The phthalocyanine SAMs on gold electrodes were investigated for electrocatalytic oxidation of 4-chlorophenol. The electrocatalytic properties of tetra- and octa- pentanethio substituted cobalt binuclear phthalocyanine (CoBiPc) are compared with their tetra- and octa-pentanethio substituted phthalocyanine (CoPc). The SAMs modified gold electrode surfaces showed a peak current enhancement and stability and reduction in electrocatalytic potentials compared to the bare or unmodified electrodes towards the detection of the 4-chlorophenol. The SAMs of cobalt binuclear phthalocyanines exhibited more enhanced electrocatalytic properties in terms of stability, detection peak current and reduction of the electrocatalytic over potential.

Comparative toxicological effects of two antifouling biocides on the marine diatom Chaetoceros lorenzianus: Damage and post-exposure recovery.

PubMed

Chavan, Pooja; Kumar, Rajesh; Kirubagaran, Ramalingam; Venugopalan, Vayalam P

2017-10-01

Antifouling biocides are commonly used in coastal electric power stations to prevent biofouling in their condenser cooling systems. However, the environmental impact of the chemical biocides is less understood than the thermal stress effects caused by the condenser effluents. In this study, Chaetoceros lorenzianus, a representative marine diatom, was used to analyse the toxicity of two antifouling biocides, chlorine and chlorine dioxide. The diatom cells were subjected to a range of concentrations of the biocides (from 0.05 to 2mg/L, as total residual oxidants, TRO) for contact time of 30min. They were analysed for viability, genotoxicity, chlorophyll a and cell density endpoints. The cells were affected at all concentrations of the biocides (0.05-2mg/L), showing dose-dependent decrease in viability and increase in DNA damage. The treated cells were later incubated in filtered seawater devoid of biocide to check for recovery. The cells were able to recover in terms of overall viability and DNA damage, when they had been initially treated with low concentrations of the biocides (0.5mg/L of Cl 2 or 0.2mg/L of ClO 2 ). Chlorophyll a analysis showed irreparable damage at all concentrations, while cell density showed increasing trend of reduction, if treated above 0.5mg/L of Cl 2 and 0.2mg/L of ClO 2 . The data indicated that in C. lorenzianus, cumulative toxic effects and recovery potential of ClO 2 up to 0.2mg/L were comparable with those of Cl 2 , up to 0.5mg/L concentration in terms of the studied endpoints. The results indicate that at the biocide levels currently being used at power stations, recovery of the organism is feasible upon return to ambient environment. Similar studies should be carried out on other planktonic and benthic organisms, which will be helpful in the formulation of future guidelines for discharge of upcoming antifouling biocides such as chlorine dioxide. Copyright © 2017 Elsevier Inc. All rights reserved.

Correlation between antibiotic and biocide resistance in mesophilic and psychrotrophic Pseudomonas spp. isolated from slaughterhouse surfaces throughout meat chain production.

PubMed

Lavilla Lerma, Leyre; Benomar, Nabil; Casado Muñoz, María del Carmen; Gálvez, Antonio; Abriouel, Hikmate

2015-10-01

The aim of this study was to evaluate biocide susceptibility in mesophilic and psychrotrophic pseudomonads isolated from surfaces of a goat and lamb slaughterhouse, which was representative of the region. To determine biocide resistance in pseudomonads, we determined for the first time the epidemiological cut-off values (ECOFFs) of benzalkonium, cetrimide, chlorhexidine, hexachlorophene, P3 oxonia, polyhexamethylene guanidine hydrochloride (PHMG), topax 66 and triclosan being generally very similar in different Pseudomonas spp. with some exceptions. Thus, resistance of pseudomonads was mainly shown to triclosan, and in lesser extent to cetrimide and benzalkonium chloride depending on the species, however they were highly susceptible to industrial formulations of biocides. By means of statistical analysis, positive correlations between antibiotics, biocides and both antimicrobials in pseudomonads were detected suggesting a co- or cross resistance between different antimicrobials in goat and lamb slaughterhouse environment. Cross-resistance between biocides and antibiotics in pseudomonads were especially detected between PHMG or triclosan and different antibiotics depending on the biocide and the population type. Thus, the use of those biocides as disinfectant in slaughterhouse zones must be carefully evaluated because of the selection pressure effect of antimicrobials on the emergence of resistant bacteria which could be spread to the consumer. It is noteworthy that specific industrial formulations such as topax 66 and oxonia P3 showed few correlations with antibiotics (none or 1-2 antibiotics) which should be taken into consideration for disinfection practices in goat and lamb slaughterhouse. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Branch-specific detection of phenols and assessment of ground water solubility].

PubMed

Fischer, F; Kerndorff, H; Kühn, S

2000-01-01

There are about 500 technically relevant phenolic compounds such as cresols, chlorophenols or nitrophenols. It is most preferable to determine phenols as single compounds via gas chromatography. Further, phenols can also be assayed as photometrically as an overall parameter (Phenolindex): however, no conclusions about specific compounds can be drawn from this type of test. Also this method is not as reliable for an hazard assessment as gas chromatography. First, not all phenols, for instance resorcinol or 1-naphthol can be determined with this method. Second, phenolic groups in humic substances, which do not constitute a threat for groundwater, are determined alongside environmentally relevant phenols using this method. In most cases, it is possible to deduce which phenols can be expected in the groundwater of contaminated sites from the type of industrial usage, such as chlorophenols and pulp bleaching or nitrophenols and the production of explosives. Phenols are formed during coal combustion for instance at cokemanufactures or gasworks. They are important raw materials for the chemical industry from which resins, surfactants, pharmaceuticals, pigments, explosives, and stabilizers are produced. During the 80's phenol, cresols, nonylphenols, anisidines, aminophenols, dihydroxybenzenes, and naphthols were manufactured in amounts exceeding 10,000 t/a. Also, phenolic compounds are used as additives in many areas for example as solvents in the electric industry, in sawmills, papermanufacture, electroplating of metal sheets, as photographic developers, as textile dyes, or for the tanning of hydes. Due to the formation and use of phenols at industrial sites, groundwater contaminations are possible via infiltration through the unsaturated zone. Especially at gasworks and ammunition factories, groundwater contaminations with phenols have become known. In the vicinity of railway tracks and associated facillities contaminations due to the use of pesticides or mineral oils are possible. Input of phenols on agricultural lands can be caused by pesticides, sewage sludge or manure. The groundwater downstream of landfills often contains phenol, chlorophenols, cresols, and xylenols. The formation of phenol from other organic contaminants as benzene in groundwater has been reported. The potential for mobilization of phenols in the saturated zone can be estimated from their physical and chemical properties. Especially low molecular weight phenols are easily mobilized due to their high solubility in water and low potential for accumulation. These compounds are: phenol, cresols, xylenols, chlorophenols, hydroxybenzenes, nitrophenols, anisidines, aminophenols, anisol, 2-phenoxyethanol, and thiophenol. The stability of phenols under laboratory conditions varies. The complete mineralization depends mainly on the experimental set-up, i.e. nutrients, temperature, and type of inocula. The anaerobic degradation of phenols is generally slower than the aerobic. Phenol is readily biodegradable under both aerobic and anaerobic conditions. In general, the biodegradability depends on the type, number and position of substitutes. Phenols with nitro-, alkyl-, or chlorosubstitutes are more recalcitrant than phenol itself. Our biodegradability test show that the decomposition of alkylphenols is determined by the length and branching of the alcyllic chain. Phenols with high contamination potential are chlorophenols, xylenols, and nitrophenols. These compounds are both mobile and recalcitrant in the saturated zone. Phenolic compounds of a medium contamination risk are dichlorophenols, trichlorophenols, cresols, and phenol because they are mobile but less stable in groundwater. These compounds are known contaminants in the groundwater at gasworks, landfills, and ammunition factories. Aminophenols, anisidines, tert-butylphenols, ethylphenols, hydroxybenzenes, and 2-phenoxyethanol also constite a potential hazard for groundwater; however, no contaminations with these compounds are known. Poisoning due to oral uptake of phenol contaminated ground- or drinking water have not been reported, which might be due to the pungent odor and taste phenolic compounds have even at very low concentrations (mg/L). Because of the taste problem, the German drinking water standard for phenols is 0.5 microgram/L. In Berlin, groundwater with phenol concentrations higher than 30 micrograms/L of alkylphenols or 2 micrograms/L of chlorophenols is considered contaminated.

Effectiveness of bromicide against Legionella pneumophila in a cooling tower

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fliermans, C.B.; Harvey, R.S.

1983-01-01

Cooling towers are considered to be man-made amplifiers of Legionella. Thus the proper maintenance and choice of biocides is important. The only biocide that has thus far been shown to be effective in field tests is the judicious use of chlorination. Perturbation studies were conducted on an industrial cooling tower shown to contain Legionella, using 1-bromo-3-chloro-5,5-dimethylhydantoin (Bromicide, Great Lakes Chemical Corp.). At the manufacturer's recommended concentrations neither the density nor the activity of Legionella was affected. At concentrations greater than 2.0 ppM free residual, the Bromicide was not effective in reducing Legionella to source water concentrations, nor was it effectivemore » in reducing the INT activity of the bacterium in situ. The data indicate that at concentrations up to 2.0 ppM, Bromicide is not effective in these tower studies. 23 references, 3 tables.« less

The microbiology of Lascaux Cave.

PubMed

Bastian, F; Jurado, V; Nováková, A; Alabouvette, C; Saiz-Jimenez, C

2010-03-01

Lascaux Cave (Montignac, France) contains paintings from the Upper Paleolithic period. Shortly after its discovery in 1940, the cave was seriously disturbed by major destructive interventions. In 1963, the cave was closed due to algal growth on the walls. In 2001, the ceiling, walls and sediments were colonized by the fungus Fusarium solani. Later, black stains, probably of fungal origin, appeared on the walls. Biocide treatments, including quaternary ammonium derivatives, were extensively applied for a few years, and have been in use again since January 2008. The microbial communities in Lascaux Cave were shown to be composed of human-pathogenic bacteria and entomopathogenic fungi, the former as a result of the biocide selection. The data show that fungi play an important role in the cave, and arthropods contribute to the dispersion of conidia. A careful study on the fungal ecology is needed in order to complete the cave food web and to control the black stains threatening the Paleolithic paintings.

Powder characteristics and biocidal activity of the MnOx-WO₃-TiO₂ system synthesized by a sol-gel method for antifouling agents.

PubMed

Shin, Byeongkil; Kim, Sangmin; Lee, Heesoo; Park, Hyun

2013-08-01

The TiO₂-system powders were investigated with respect to the crystallinity and the microstructure. The biocidal activity increased from TiO₂ to binary MnOx-TiO₂ to ternary MnOx-WO₃-TiO₂ against Vibrio fischeri as a model of Gram-negative bacteria. Anatase and rutile TiO₂ were not toxic even at 200 mg/L, but anatase has been observed in bacterial growth inhibition due to the different electronic band (lattice) structure. All materials containing manganese oxides were toxic: the toxicity correlation (EC₅₀) of MnOx-WO₃ and MnOx-WO₃-TiO₂ was 7.0, 1.8 ppm, respectively. The high antifouling activity of MnOx-WO₃-TiO₂ was attributed to its redox potential and soluble metal ions originating from tungsten oxides according to the improvements in the powder characteristics.

Why does Kevlar decompose, while Nomex does not, when treated with aqueous chlorine solutions?

PubMed

Akdag, Akin; Kocer, Hasan B; Worley, S D; Broughton, R M; Webb, T R; Bray, Travis H

2007-05-24

Kevlar and Nomex are high-performance polymers which have wide varieties of applications in daily life. Recently, they have been proposed to be biocidal materials when reacted with household bleach (sodium hypochlorite solution) because they contain amide moieties which can be chlorinated to generate biocidal N-halamine functional groups. Although Nomex can be chlorinated without any significant decomposition, Kevlar decomposes under the same chlorination conditions. In this study, two mimics for each of the polymers were synthesized to simulate the carboxylate and diaminophenylene components of the materials. It was found that the p-diaminophenylene component of the Kevlar mimic is oxidized to a quinone-type structure upon treatment with hypochlorous acid, which then decomposes. However, such a mechanism for the Nomex mimic is not possible. In this paper, based upon these observations, a plausible answer will be provided to the title question.

Leaching of biocides used in façade coatings under laboratory test conditions.

PubMed

Schoknecht, Ute; Gruycheva, Jana; Mathies, Helena; Bergmann, Hannelore; Burkhardt, Michael

2009-12-15

The European Biocidal Products Directive 98/8/EC requires a risk assessment concerning possible effects of active ingredients on the environment. Biocides can be leached from treated materials exposed to outdoor use. These emissions have to be estimated and evaluated during the authorization procedure. Different immersion and irrigation tests were performed to investigate leaching of biocides from façade coatings. Several marketed formulations of textured coatings and paints spiked with a mixture of commonly used active ingredients (OIT, DCOIT, IPBC, carbendazim, isoproturon, diuron, terbutryn, and Irgarol 1051) were investigated. The emission process can be described by time-dependent functions that depend on the test conditions. The results of all test procedures confirm that leachability is related to water solubility and n-octanol-water partition coefficient of the active ingredients and that leaching of biocides from façade coatings is mainly a diffusion controlled process. Other factors like the composition of the product, availability and transport of water, concentration of active ingredients in the coatings, as well as UV-exposure of the coatings influence biocide emissions.

Rapid and effective decontamination of chlorophenol-contaminated soil by sorption into commercial polymers: concept demonstration and process modeling.

PubMed

Tomei, M Concetta; Mosca Angelucci, Domenica; Ademollo, Nicoletta; Daugulis, Andrew J

2015-03-01

Solid phase extraction performed with commercial polymer beads to treat soil contaminated by chlorophenols (4-chlorophenol, 2,4-dichlorophenol and pentachlorophenol) as single compounds and in a mixture has been investigated in this study. Soil-water-polymer partition tests were conducted to determine the relative affinities of single compounds in soil-water and polymer-water pairs. Subsequent soil extraction tests were performed with Hytrel 8206, the polymer showing the highest affinity for the tested chlorophenols. Factors that were examined were polymer type, moisture content, and contamination level. Increased moisture content (up to 100%) improved the extraction efficiency for all three compounds. Extraction tests at this upper level of moisture content showed removal efficiencies ≥70% for all the compounds and their ternary mixture, for 24 h of contact time, which is in contrast to the weeks and months, normally required for conventional ex situ remediation processes. A dynamic model characterizing the rate and extent of decontamination was also formulated, calibrated and validated with the experimental data. The proposed model, based on the simplified approach of "lumped parameters" for the mass transfer coefficients, provided very good predictions of the experimental data for the absorptive removal of contaminants from soil at different individual solute levels. Parameters evaluated from calibration by fitting of single compound data, have been successfully applied to predict mixture data, with differences between experimental and predicted data in all cases being ≤3%. Copyright © 2014 Elsevier Ltd. All rights reserved.

Modeling of adsorption isotherms of phenol and chlorophenols onto granular activated carbon. Part I. Two-parameter models and equations allowing determination of thermodynamic parameters.

PubMed

Hamdaoui, Oualid; Naffrechoux, Emmanuel

2007-08-17

The adsorption equilibrium isotherms of five phenolic compounds from aqueous solutions onto granular activated carbon (GAC) were studied and modeled. Phenol (Ph), 2-chlorophenol (2-CP), 4-chlorophenol (4-CP), 2,4-dichlorophenol (DCP), and 2,4,6-trichlorophenol (TCP) were chosen for the adsorption tests. To predict the adsorption isotherms and to determine the characteristic parameters for process design, seven isotherm models: Langmuir (five linear forms), Freundlich, Elovich, Temkin, Fowler-Guggenheim, Kiselev, and Hill-de Boer models were applied to experimental data. The results reveal that the adsorption isotherm models fitted the data in the order: Fowler-Guggenheim>Hill-de Boer>Temkin>Freundlich>Kiselev>Langmuir isotherms. Adsorption isotherms modeling shows that the interaction of phenolic compounds with activated carbon surface is localized monolayer adsorption, that is adsorbed molecules are adsorbed at definite, localized sites. Each site can accommodate only one molecule. The interaction among adsorbed molecules is repulsive and there is no association between them, adsorption is carried out on energetically different sites and is an exothermic process. Uptake of phenols increases in the order Ph<2-CP<4-CP

Alkanols and chlorophenols cause different physiological adaptive responses on the level of cell surface properties and membrane vesicle formation in Pseudomonas putida DOT-T1E.

PubMed

Baumgarten, Thomas; Vazquez, José; Bastisch, Christian; Veron, Wilfried; Feuilloley, Marc G J; Nietzsche, Sandor; Wick, Lukas Y; Heipieper, Hermann J

2012-01-01

In order to cope with the toxicity imposed by the exposure to environmental hydrocarbons, many bacteria have developed specific adaptive responses such as modifications in the cell envelope. Here we compared the influence of n-alkanols and chlorophenols on the surface properties of the solvent-tolerant bacterium Pseudomonas putida DOT-T1E. In the presence of toxic concentrations of n-alkanols, this strain significantly increased its cell surface charge and hydrophobicity with changes depending on the chain length of the added n-alkanols. The adaptive response occurred within 10 min after the addition of the solvent and was demonstrated to be of physiological nature. Contrary to that, chlorophenols of similar hydrophobicity and potential toxicity as the corresponding alkanols caused only minor effects in the surface properties. To our knowledge, this is the first observation of differences in the cellular adaptive response of bacteria to compound classes of quasi equal hydrophobicity and toxicity. The observed adaptation of the physico-chemical surface properties of strain DOT-T1E to the presence of alkanols was reversible and correlated with changes in the composition of the lipopolysaccharide content of the cells. The reaction is explained by previously described reactions allowing the release of membrane vesicles that was demonstrated for cells affected by 1-octanol and heat shock, whereas no membrane vesicles were released after the addition of chlorophenols.

Silver biocide's real-world success.

PubMed

Pearson, Susan

2015-03-01

Although temperature control has been the UK's longest-serving means of controlling the growth and proliferation of Legionella in hot and cold water systems, there are other factors, including major rises in energy costs, that warrant the use of biocides--including in the healthcare sector. In 2000, the HSE's new 'L8' guidelines took this into account, giving equal weight to both temperature reg~mes and biocides, such as chlorine dioxide, as control methods. Susan Pearson BSc reports on one potentially effective biocide- silver hydrogen peroxide, explains how it 'works' in practice, and highlights the recent 'real-world' evidence of its effectiveness and advantages.

The environmental fate and effects of antifouling paint biocides.

PubMed

Thomas, K V; Brooks, S

2010-01-01

Antifouling (AF) biocides are the active ingredients in AF paints that prevent the settlement, adhesion and growth of organisms to a painted surface. A wide range of chemicals are used as AF biocides, which have very different physico-chemical properties and therefore differing environmental fates, behaviour and effects. Copper has been used as an antifoulant for centuries and extensive research has been performed to understand how copper speciation influences bioavailability and toxicity. For biocides that have been widely used over a number of decades, for example Irgarol 1051 and diuron, there are a large amount of environmental data in the public domain, including for their respective metabolites, that allows their environmental safety and potential risk to the environment to be assessed. For other biocides such as dichlofluanid, DCOIT (SeaNine 211) and zinc/copper pyrithione, there is a good understanding of their fate and effects. However, few monitoring studies have been performed and not so much is known about the fate and effects of their metabolites. There are also new or candidate biocides such as triphenylborane pyridine, Econea, capsaicin and medetomidine for which there is very little information in the public domain. This review provides an overview of the environmental fate and occurrence data that are in the public domain for AF biocides and provides some insight into the effects of these compounds on non-target organisms.

2-(Decylthio)ethanamine hydrochloride: A new multifunctional biocide which enhances corrosion inhibition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walter, R.W.; Cooke, L.M.

1997-12-01

2-(Decylthio)ethanamine hydrochloride is a new multifunctional biocide that is registered for use in a variety of recirculating cooling water systems. This biocide has broad spectrum activity against bacteria, fungi and algae. It also has biofilm and corrosion inhibition properties. Data on these various activities will be presented for both laboratory and field evaluations.

Lung cancer mortality and exposure to synthetic metalworking fluid and biocides: controlling for the healthy worker survivor effect.

PubMed

Garcia, Erika; Picciotto, Sally; Neophytou, Andreas M; Bradshaw, Patrick T; Balmes, John R; Eisen, Ellen A

2018-05-09

Synthetic metalworking fluids (MWFs), widely used to cool and lubricate industrial machining and grinding operations, have been linked with increased risk of several cancers. Estimates of their relation with lung cancer, however, are inconsistent. Controlling for the healthy worker survivor effect, we examined the relations between lung cancer mortality and exposure to synthetic MWF, as well as to biocides added to water-based fluids to control microbial growth, in a cohort of autoworkers. Biocides served as a marker for endotoxin, which has reported antitumour effects, and were hypothesised to be the reason prior studies found reduced lung cancer risk associated with exposure to synthetic fluids. Using the parametric g-formula, we estimated risk ratios (RRs) comparing cumulative lung cancer mortality under no intervention with what would have occurred under hypothetical interventions reducing exposure to zero (ie, a ban) separately for two exposures: synthetic fluids and biocides. We also specified an intervention on synthetic MWF and biocides simultaneously to estimate joint effects. Under a synthetic MWF ban, we observed decreased lung cancer mortality risk at age 86, RR=0.96 (0.91-1.01), but when we also intervened to ban biocides, the RR increased to 1.03 (0.95-1.11). A biocide-only ban increased lung cancer mortality (RR=1.07 (1.00-1.16)), with slightly larger RR in younger ages. Findings suggest a modest positive association for synthetic MWF with lung cancer mortality, contrary to the negative associations reported in earlier studies. Biocide exposure, however, was inversely associated with risk of lung cancer mortality. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Selection of an Alternate Biocide for the ISS Internal Thermal Control System Coolant, Phase 2

NASA Technical Reports Server (NTRS)

Wilson, Mark E.; Cole, Harold; Weir, Natalee; Oehler, Bill; Steele, John; Varsik, Jerry; Lukens, Clark

2004-01-01

The ISS (International Space Station) ITCS (Internal Thermal Control System) includes two internal coolant loops that utilize an aqueous based coolant for heat transfer. A silver salt biocide had previously been utilized as an additive in the coolant formulation to control the growth and proliferation of microorganisms within the coolant loops. Ground-based and in-flight testing demonstrated that the silver salt was rapidly depleted, and did not act as an effective long-term biocide. Efforts to select an optimal alternate biocide for the ITCS coolant application have been underway and are now in the final stages. An extensive evaluation of biocides was conducted to down-select to several candidates for test trials and was reported on previously. Criteria for that down-select included: the need for safe, non-intrusive implementation and operation in a functioning system; the ability to control existing planktonic and biofilm residing microorganisms; a negligible impact on system-wetted materials of construction; and a negligible reactivity with existing coolant additives. Candidate testing to provide data for the selection of an optimal alternate biocide is now in the final stages. That testing has included rapid biocide effectiveness screening using Biolog MT2 plates to determine minimum inhibitory concentration (amount that will inhibit visible growth of microorganisms), time kill studies to determine the exposure time required to completely eliminate organism growth, materials compatibility exposure evaluations, coolant compatibility studies, and bench-top simulated coolant testing. This paper reports the current status of the effort to select an alternate biocide for the ISS ITCS coolant. The results of various test results to select the optimal candidate are presented.

Aspects of tests and assessment of filtering materials used for respiratory protection against bioaerosols. Part I: type of active substance, contact time, microorganism species.

PubMed

Majchrzycka, Katarzyna; Gutarowska, Beata; Brochocka, Agnieszka

2010-01-01

This paper presents the results of a study on antimicrobial activity of polymer filter nonwovens produced by needle-punching or melt-blowing with an addition of disinfecting agents. The first part of the paper discusses how the biocidal activity of nonwovens is a function of the active agent added to the nonwovens, the duration of the contact of microorganisms with nonwovens and the type of microorganisms. The types of fibres and disinfecting agents had a considerable effect on the biocidal activity of nonwovens. The biocidal effect of nonwovens increased with the duration of their contact with microorganisms. Fibre activity differed considerably depending on the species of the microorganism. The microorganisms most sensitive to biocidal activity of the active filter nonwoven were S. aureus, M. flavus and E. coli. There were no biocidal effects on spore-forming bacterium B. subtilis.

Encapsulation of biocides by cyclodextrins: toward synergistic effects against pathogens

PubMed Central

Nardello-Rataj, Véronique

2014-01-01

Summary Host–guest chemistry is useful for the construction of nanosized objects. Some of the widely used hosts are probably the cyclodextrins (CDs). CDs can form water-soluble complexes with numerous hydrophobic compounds. They have been widespread used in medicine, drug delivery and are of interest for the biocides encapsulation. Indeed, this enables the development of more or less complex systems that release antimicrobial agents with time. In this paper, the general features of CDs and their applications in the field of biocides have been reviewed. As the key point is the formation of biocide–CD inclusion complexes, this review deals with this in depth and the advantages of biocide encapsulation are highlighted throughout several examples from the literature. Finally, some future directions of investigation have been proposed. We hope that scientists studying biocide applications receive inspiration from this review to exploit the opportunities offered by CDs in their respective research areas. PMID:25550722

A survey of antifoulants in sediments from Ports and Marinas along the French Mediterranean coast.

PubMed

Cassi, Roberto; Tolosa, Imma; de Mora, Stephen

2008-11-01

Due to deleterious effects on non-target organisms, the use of organotin compounds on boat hulls of small vessels (<25 m) has been widely prohibited. The International Maritime Organisation (IMO) resolved that the complete prohibition on organotin compounds acting as biocides in antifouling systems should commence in 2008. As a result of restrictions on the use of organotin based paints, other antifouling formulations containing organic biocides have been utilised. This survey was conducted to assess the contamination of replacement biocides in the marine environment following the ban of TBT-based paints. Surface sediments samples were collected in the major ports and marinas along the France Mediterranean coastline (Cote d'Azur) and analysed for organotin compounds, Irgarol 1051, Sea-nine 211, Chlorothalonil, Dichlofluanid and Folpet. Every port and marina exhibited high levels of organotin compounds, with concentrations in sediments ranging from 37 ng Sn g(-1) dry wt in Menton Garavan to over 4000 ng Sn g(-1) dry wt close to the ship chandler within the port of Villefranche-sur-Mer. TBT degradation indexes suggested that fresh inputs are still made. Among the other antifoulants monitored, only Irgarol 1051 exhibited measurable concentrations in almost every port, with concentrations ranging from 40 ng g(-1) dry wt (Cannes) to almost 700 ng g(-1) dry wt (Villefranche-sur-Mer, ship chandler).

A simple and rapid method for optical visualization and quantification of bacteria on textiles

PubMed Central

Stiefel, Philipp; Schneider, Jana; Amberg, Caroline; Maniura-Weber, Katharina; Ren, Qun

2016-01-01

To prevent bacterial contamination on textiles and the associated undesired effects different biocidal coatings have been investigated and applied. However, due to health and environmental concerns anti-adhesive coatings preventing the binding of bacteria would be favored. To develop such anti-adhesive coatings simple assays for reliable and fast screening are beneficial. Here an easy-to-handle, robust and rapid assay to assess bacteria on textiles utilizing a tetrazolium salt was reported. The assay allowed direct eye visualization of the color change of the textiles containing bacteria, facilitating fast screening. Quantification of the adhered bacteria could be done by generating standard curves which correlate the staining intensity to cell numbers. An additional advantage of the described assay is that with the same detection method anti-adhesive and biocidal effects can be investigated. The method was applied to different coatings, using Pseudomonas aeruginosa and Staphylococcus aureus as model organisms. The detection limit was found to be between 2.5 * 106 and 9.4 * 108 for P. aeruginosa and between 1 * 106 and 3.3 * 108 for S. aureus. The anti-adhesive coating PLUMA was demonstrated to reduce bacterial adhesion without killing them, whereas the biocidal coating TH22-27 caused a clear reduction in the number of viable cells. PMID:28004762

Biocidal properties of maltose reduced silver nanoparticles against American foulbrood diseases pathogens.

PubMed

Çulha, Mustafa; Kalay, Şaban; Sevim, Elif; Pinarbaş, Müberra; Baş, Yıldız; Akpinar, Rahşan; Karaoğlu, Şengül Alpay

2017-12-01

Bee disease caused by spore-forming Paenibacillus larvae and Paenibacillus alvei is a serious problem for honey production. Thus, there is an ongoing effort to find an effective agent that shows broad biocidal activity with minimal environmental hazard. In this study, the biocidal effect of maltose reduced silver nanoparticles (AgNPs) is evaluated against American foulbrood and European foulbrood pathogens. The results demonstrate that the maltose reduced AgNPs are excellent short and long-term biocides against P. larvae isolates. The long-term effect suggests that the Ag + ions are released from the AgNPs with increasing time in a controlled manner.

Effects of single and repeated exposure to biocidal active substances on the barrier function of the skin in vitro.

PubMed

Buist, Harrie E; van de Sandt, Johannes J M; van Burgsteden, Johan A; de Heer, Cees

2005-10-01

The dermal route of exposure is important in worker exposure to biocidal products. Many biocidal active substances which are used on a daily basis may decrease the barrier function of the skin to a larger extent than current risk assessment practice addresses, due to possible skin effects of repeated exposure. The influence of repeated and single exposure to representative biocidal active substances on the skin barrier was investigated in vitro. The biocidal active substances selected were alkyldimethylbenzylammonium chloride (ADBAC), boric acid, deltamethrin, dimethyldidecylammonium chloride (DDAC), formaldehyde, permethrin, piperonyl butoxide, sodium bromide, and tebuconazole. Of these nine compounds, only the quaternary ammonium chlorides ADBAC and DDAC had a clear and consistent influence on skin permeability of the marker compounds tritiated water and [(14)C]propoxur. For these compounds, repeated exposure increased skin permeability more than single exposure. At high concentrations the difference between single and repeated exposure was quantitatively significant: repeated exposure to 300 mg/L ADBAC increased skin permeability two to threefold in comparison to single exposure. Therefore, single and repeated exposure to specific biocidal products may significantly increase skin permeability, especially when used undiluted.

Importance of Porins for Biocide Efficacy against Mycobacterium smegmatis▿

PubMed Central

Frenzel, Elrike; Schmidt, Stefan; Niederweis, Michael; Steinhauer, Katrin

2011-01-01

Mycobacteria are among the microorganisms least susceptible to biocides but cause devastating diseases, such as tuberculosis, and increasingly opportunistic infections. The exceptional resistance of mycobacteria to toxic solutes is due to an unusual outer membrane, which acts as an efficient permeability barrier, in synergy with other resistance mechanisms. Porins are channel-forming proteins in the outer membrane of mycobacteria. In this study we used the alamarBlue assay to show that the deletion of Msp porins in isogenic mutants increased the resistance of Mycobacterium smegmatis to isothiazolinones (methylchloroisothiazolinone [MCI]/methylisothiazolinone [MI] and octylisothiazolinone [2-n-octyl-4-isothiazolin-3-one; OIT]), formaldehyde-releasing biocides {hexahydrotriazine [1,3,5-tris (2-hydroxyethyl)-hexahydrotriazine; HHT] and methylenbisoxazolidine [N,N′-methylene-bis-5-(methyloxazolidine); MBO]}, and the lipophilic biocides polyhexamethylene biguanide and octenidine dihydrochloride 2- to 16-fold. Furthermore, the susceptibility of the porin triple mutant against a complex disinfectant was decreased 8-fold compared to wild-type (wt) M. smegmatis. Efficacy testing in the quantitative suspension test EN 14348 revealed 100-fold improved survival of the porin mutant in the presence of this biocide. These findings underline the importance of porins for the susceptibility of M. smegmatis to biocides. PMID:21398489

Comprehensive Evaluation of Biological Growth Control by Chlorine-Based Biocides in Power Plant Cooling Systems Using Tertiary Effluent

PubMed Central

Chien, Shih-Hsiang; Dzombak, David A.; Vidic, Radisav D.

2013-01-01

Abstract Recent studies have shown that treated municipal wastewater can be a reliable cooling water alternative to fresh water. However, elevated nutrient concentration and microbial population in wastewater lead to aggressive biological proliferation in the cooling system. Three chlorine-based biocides were evaluated for the control of biological growth in cooling systems using tertiary treated wastewater as makeup, based on their biocidal efficiency and cost-effectiveness. Optimal chemical regimens for achieving successful biological growth control were elucidated based on batch-, bench-, and pilot-scale experiments. Biocide usage and biological activity in planktonic and sessile phases were carefully monitored to understand biological growth potential and biocidal efficiency of the three disinfectants in this particular environment. Water parameters, such as temperature, cycles of concentration, and ammonia concentration in recirculating water, critically affected the biocide performance in recirculating cooling systems. Bench-scale recirculating tests were shown to adequately predict the biocide residual required for a pilot-scale cooling system. Optimal residuals needed for proper biological growth control were 1, 2–3, and 0.5–1 mg/L as Cl2 for NaOCl, preformed NH2Cl, and ClO2, respectively. Pilot-scale tests also revealed that Legionella pneumophila was absent from these cooling systems when using the disinfectants evaluated in this study. Cost analysis showed that NaOCl is the most cost-effective for controlling biological growth in power plant recirculating cooling systems using tertiary-treated wastewater as makeup. PMID:23781129

Comprehensive Evaluation of Biological Growth Control by Chlorine-Based Biocides in Power Plant Cooling Systems Using Tertiary Effluent.

PubMed

Chien, Shih-Hsiang; Dzombak, David A; Vidic, Radisav D

2013-06-01

Recent studies have shown that treated municipal wastewater can be a reliable cooling water alternative to fresh water. However, elevated nutrient concentration and microbial population in wastewater lead to aggressive biological proliferation in the cooling system. Three chlorine-based biocides were evaluated for the control of biological growth in cooling systems using tertiary treated wastewater as makeup, based on their biocidal efficiency and cost-effectiveness. Optimal chemical regimens for achieving successful biological growth control were elucidated based on batch-, bench-, and pilot-scale experiments. Biocide usage and biological activity in planktonic and sessile phases were carefully monitored to understand biological growth potential and biocidal efficiency of the three disinfectants in this particular environment. Water parameters, such as temperature, cycles of concentration, and ammonia concentration in recirculating water, critically affected the biocide performance in recirculating cooling systems. Bench-scale recirculating tests were shown to adequately predict the biocide residual required for a pilot-scale cooling system. Optimal residuals needed for proper biological growth control were 1, 2-3, and 0.5-1 mg/L as Cl 2 for NaOCl, preformed NH 2 Cl, and ClO 2 , respectively. Pilot-scale tests also revealed that Legionella pneumophila was absent from these cooling systems when using the disinfectants evaluated in this study. Cost analysis showed that NaOCl is the most cost-effective for controlling biological growth in power plant recirculating cooling systems using tertiary-treated wastewater as makeup.

Significant Differences Characterise the Correlation Coefficients between Biocide and Antibiotic Susceptibility Profiles in Staphylococcus aureus.

PubMed

Oggioni, Marco R; Coelho, Joana Rosado; Furi, Leonardo; Knight, Daniel R; Viti, Carlo; Orefici, Graziella; Martinez, Jose-Luis; Freitas, Ana Teresa; Coque, Teresa M; Morrissey, Ian

2015-01-01

There is a growing concern by regulatory authorities for the selection of antibiotic resistance caused by the use of biocidal products. We aimed to complete the detailed information on large surveys by investigating the relationship between biocide and antibiotic susceptibility profiles of a large number of Staphylococcus aureus isolates using four biocides and antibiotics commonly used in clinical practice. The minimal inhibitory concentration (MIC) for most clinically-relevant antibiotics was determined according to the standardized methodology for over 1600 clinical S. aureus isolates and compared to susceptibility profiles of benzalkonium chloride, chlorhexidine, triclosan, and sodium hypochlorite. The relationship between antibiotic and biocide susceptibility profiles was evaluated using non-linear correlations. The main outcome evidenced was an absence of any strong or moderate statistically significant correlation when susceptibilities of either triclosan or sodium hypochlorite were compared for any of the tested antibiotics. On the other hand, correlation coefficients for MICs of benzalkonium chloride and chlorhexidine were calculated above 0.4 for susceptibility to quinolones, beta-lactams, and also macrolides. Our data do not support any selective pressure for association between biocides and antibiotics resistance and furthermore do not allow for a defined risk evaluation for some of the compounds. Importantly, our data clearly indicate that there does not involve any risk of selection for antibiotic resistance for the compounds triclosan and sodium hypochlorite. These data hence infer that biocide selection for antibiotic resistance has had so far a less significant impact than feared.

Effects of Antifouling Biocides on Molecular and Biochemical Defense System in the Gill of the Pacific Oyster Crassostrea gigas.

PubMed

Park, Mi Seon; Kim, Young Dae; Kim, Bo-Mi; Kim, Youn-Jung; Kim, Jang Kyun; Rhee, Jae-Sung

2016-01-01

Antifouling biocides such as organotin compounds and their alternatives are potent toxicants in marine ecosystems. In this study, we employed several molecular and biochemical response systems of the Pacific oyster Crassostrea gigas to understand a potential mode of action of antifouling biocides (i.e. tributyltin (TBT), diuron and irgarol) after exposure to different concentrations (0.01, 0.1, and 1 μg L-1) for 96 h. As a result, all the three antifouling biocides strongly induced the antioxidant defense system. TBT reduced both enzymatic activity and mRNA expression of Na+/K+-ATPase and acetylcholinesterase (AChE). Lower levels of both Na+/K+-ATPase activity and AChE mRNA expression were observed in the diuron-exposed oysters compared to the control, while the irgarol treatment reduced only the transcriptional expression of AChE gene. We also analyzed transcript profile of heat shock protein (Hsp) superfamily in same experimental conditions. All antifouling biocides tested in this study significantly modulated mRNA expression of Hsp superfamily with strong induction of Hsp70 family. Taken together, overall results indicate that representative organotin TBT and alternatives have potential hazardous effects on the gill of C. gigas within relatively short time period. Our results also suggest that analyzing a series of molecular and biochemical parameters can be a way of understanding and uncovering the mode of action of emerging antifouling biocides. In particular, it was revealed that Pacific oysters have different sensitivities depend on the antifouling biocides.

A new combined green method for 2-Chlorophenol removal using cross-linked Brassica rapa peroxidase in silicone oil.

PubMed

Tandjaoui, Nassima; Abouseoud, Mahmoud; Couvert, Annabelle; Amrane, Abdeltif; Tassist, Amina

2016-04-01

This study proposes a new technique to treat waste air containing 2-Chlorophenol (2-CP), namely an integrated process coupling absorption of the compound in an organic liquid phase and its enzymatic degradation. Silicone oil (47V20) was used as an organic absorbent to allow the volatile organic compound (VOC) transfer from the gas phase to the liquid phase followed by its degradation by means of Cross-linked Brassica rapa peroxidase (BRP) contained in the organic phase. An evaluation of silicone oil (47V20) absorption capacity towards 2-CP was first accomplished by determining its partition coefficient (H) in this solvent. The air-oil partition coefficient of 2-CP was found equal to 0.136 Pa m(3) mol(-1), which is five times lower than the air-water value (0.619 Pam(3) mol(-1)). The absorbed 2-CP was then subject to enzymatic degradation by cross-linked BRP aggregates (BRP-CLEAs). The degradation step was affected by four parameters (contact time; 2-CP, hydrogen peroxide and enzyme concentrations), which were optimized in order to obtain the highest conversion yield. A maximal conversion yield of 69% and a rate of 1.58 mg L(-1) min(-1)were obtained for 100 min duration time when 2-CP and hydrogen peroxide concentrations were respectively 80 mg L(-1) and 6 mM in the presence of 2.66 UI mL(-1) BRP-CLEAs. The reusability of BRP-CLEAs in silicone oil was assessed, showing promising results since 59% of their initial efficiency remained after three batches. Copyright © 2016 Elsevier Ltd. All rights reserved.

Technical Basis for the Removal of Unremediated Nitrate Salt Sampling (UNS) to Support LANL Treatment Studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Funk, David John

2016-05-05

The sampling of unremediated nitrate salts (UNS) was originally proposed by the U.S. Department of Energy (DOE) and Los Alamos National Security, LLC (LANS) (collectively, the Permittees) as a means to ensure adequate understanding and characterization of the problematic waste stream created when the Permittees remediated these nitrate salts-bearing waste with an organic absorbent. The proposal to sample the UNS was driven by a lack of understanding with respect to the radioactive contamination release that occurred within the underground repository at the Waste Isolation Pilot Plant (WIPP) in February 14, 2014, as well as recommendations made by a Peer Reviewmore » Team. As discussed, the Permittees believe that current knowledge and understanding of the waste has sufficiently matured such that this additional sampling is not required. Perhaps more importantly, the risk of both chemical and radiological exposure to the workers sampling the UNS drum material is unwarranted. This memo provides the technical justification and rationale for excluding the UNS sampling from the treatment studies.« less

Wetland mitigation compliance in the western upper peninsula of Michigan.

PubMed

Hornyak, Melissa M; Halvorsen, Kathleen E

2003-11-01

The Army Corps of Engineers (ACE) is generally responsible for the implementation of federal Clean Water Act wetland regulations. It therefore plays an important role in the protection of wetlands within the United States. Unfortunately, past evaluators of ACE's implementation of these regulations found low rates of regulatory compliance. However, the fact that two states have taken responsibility for the implementation of these regulations within their boundaries provided the opportunity to assess whether one of these states might be doing a better job of enforcement. This paper reports on compliance with some of these regulations within one Michigan region. We evaluated permittee compliance with paperwork filing requirements related to wetland mitigation projects. Sixty-seven percent of county road commission permittees were out of compliance with at least one filing requirement. Forty percent of private and non-county government permittees were out of compliance. Our results therefore suggest that serious problems exist with Michigan's implementation of wetland regulations. They do not suggest that compliance in this state is significantly better than in states under ACE administration. We believe that increased agency monitoring and enforcement would improve compliance.

Adsorption and bio-sorption of nickel ions and reuse for 2-chlorophenol catalytic ozonation oxidation degradation from water.

PubMed

Ma, Wei; Zong, Panpan; Cheng, Zihong; Wang, Baodong; Sun, Qi

2014-02-15

This work explored the preparation of an effective and low-cost catalyst and investigated its catalytic capacity for 2-chlorophenol ozonation oxidation degradation in wastewater by using an ozone oxidation batch reactor. The catalyst was directly prepared by the reuse of fly ash and sawdust after saturated adsorption of nickel ions from wastewater, which was proposed as an efficient and economic approach. The obtained catalyst was characterized by TGA, BET, FTIR, XRD, and SEM, the results showed that fly ash as the basic framework has high specific surface area and the addition of sawdust as the porogen agent could improve the pore structure of the catalyst. The adsorption of nickel ions by fly ash and sawdust from aqueous solution was also investigated in this study. The results obtained from the experiments indicated that adsorption of nickel ions by fly ash and biomass sawdust could be well described by Langmuir isotherm model and pseudo second order kinetic model. The catalytic performance of catalyst was studied in terms of the effect of time, liquid-solid ratio and pH on 2-chlorophenol ozonation degradation. It was found that the catalyst could effectively improve the ozonation reaction rate at pH=7 with a 2:1 liquid-solid ratio. The kinetic study demonstrated that the reaction followed the first order model, and the rate constant increased 267% (0.03-0.1 min(-1)) of 2-chlorophenol ozonation degradation with 5 mmol/L concentration at pH=7.0 compared with ozonation alone. Copyright © 2013 Elsevier B.V. All rights reserved.

Comparison of reductive dechlorination of p-chlorophenol using Fe0 and nanosized Fe0.

PubMed

Cheng, Rong; Wang, Jian-Long; Zhang, Wei-xian

2007-06-01

Chlorophenols, as a kind of important contaminants in groundwater, are toxic and difficult to biodegrade. Laboratory tests were conducted to examine zero-valent iron as an enhancing agent in the dechlorination of chlorinated organic compounds. Nanoscale iron particles were synthesized from common precursors KBH(4) and FeSO(4). Batch experiments were performed to investigate the reduction of p-chlorophenol (4-CP) by both common Fe(0) and nanoscale Fe(0). Comparison of 300 mesh/100 mesh/commercial reductive iron powders showed that size of iron particles played an important role in reduction process. Initial concentration and pretreatment of iron particles also influenced the chlorination rate. Nanoscale Fe(0) offered much more advantages for treatment of 4-CP compared with common iron particles, such as stability and durability. And they can be used to treat contaminants in groundwater over a long time. Among different parts of synthesized nanoscale iron particle solution, the very fine particles were the major agent for treatment of pollutants. As for preservation of nanoscale Fe(0), ethanol was recommended.

Theoretical Mechanistic and Kinetic Studies on Homogeneous Gas-Phase Formation of Polychlorinated Naphthalene from 2-Chlorophenol as Forerunner

PubMed Central

Xu, Fei; Zhang, Ruiming; Li, Yunfeng; Zhang, Qingzhu; Wang, Wenxing

2015-01-01

Polychlorinated naphthalenes (PCNs) are dioxins-like compounds and are formed along with polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in thermal and combustion procedures. Chlorophenols (CPs) are the most important forerunners of PCNs. A comprehensive comprehension of PCN formation procedure from CPs is a precondition for reducing the discharge of PCNs. Experiments on the formation of PCNs from CPs have been hindered by PCN toxicity and short of precise detection methods for active intermediate radicals. In this work, PCN formation mechanism in gas-phase condition from 2-chlorophenol (2-CP) as forerunner was studied by quantum chemistry calculations. Numbers of energetically advantaged formation routes were proposed. The rate constants of key elementary steps were calculated over 600–1200 K using canonical variational transition-state theory (CVT) with small curvature tunneling contribution (SCT) method. This study illustrates formation of PCNs with one chlorine atom loss from 2-CP is preferred over that without chlorine atom loss. In comparison with formation of PCDFs from 2-CP, PCN products are less chlorinated and have lower formation potential. PMID:26516839

Theoretical Mechanistic and Kinetic Studies on Homogeneous Gas-Phase Formation of Polychlorinated Naphthalene from 2-Chlorophenol as Forerunner.

PubMed

Xu, Fei; Zhang, Ruiming; Li, Yunfeng; Zhang, Qingzhu; Wang, Wenxing

2015-10-26

Polychlorinated naphthalenes (PCNs) are dioxins-like compounds and are formed along with polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in thermal and combustion procedures. Chlorophenols (CPs) are the most important forerunners of PCNs. A comprehensive comprehension of PCN formation procedure from CPs is a precondition for reducing the discharge of PCNs. Experiments on the formation of PCNs from CPs have been hindered by PCN toxicity and short of precise detection methods for active intermediate radicals. In this work, PCN formation mechanism in gas-phase condition from 2-chlorophenol (2-CP) as forerunner was studied by quantum chemistry calculations. Numbers of energetically advantaged formation routes were proposed. The rate constants of key elementary steps were calculated over 600-1200 K using canonical variational transition-state theory (CVT) with small curvature tunneling contribution (SCT) method. This study illustrates formation of PCNs with one chlorine atom loss from 2-CP is preferred over that without chlorine atom loss. In comparison with formation of PCDFs from 2-CP, PCN products are less chlorinated and have lower formation potential.

NMED Correspondence Related to Notice of Intent for Chromium Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martinez, Ellena Isabel

Two methods of injection using a solution containing 50 kilograms (kg) of tracer are proposed for each well. Half of the tracer (25 kg) may be mixed with 3,000 gallons of potable water and delivered into a scheduled injection stream of treated groundwater as permitted in OP-1835 over a five to seven-hour period. This procedure would then be repeated on a consecutive second day. Alternatively, 5 kg of tracer may be added to each of ten 3,000-gallon tanks for a total of 30,000 gallons of tracer solution that may be injected independently of other injection flow over a period ofmore » up to five days. The permittees request that the types and masses of tracers that may be utilized per each injection well remain flexible enough to allow for one or more of the naphthalene sulfonate tracers to be substituted with a different naphthalene sulfonate. This need for flexibility is due to the availability of the tracers and any tracer listed that is designated for a given CrIN well may be interchanged with a tracer that is designated for another CrIN well, pending final NMED approval. The permittees are not allowed to introduce any new tracers and will submit a final work plan prior to each injection for each CrIN well.« less

Inactivation of Bacillus anthracis Spores by a Combination of Biocides and Heating under High-Temperature Short-Time Pasteurization Conditions ▿

PubMed Central

Xu, Sa; Labuza, Theodore P.; Diez-Gonzalez, Francisco

2008-01-01

The milk supply is considered a primary route for a bioterrorism attack with Bacillus anthracis spores because typical high-temperature short-time (HTST) pasteurization conditions cannot inactivate spores. In the event of intentional contamination, an effective method to inactivate the spores in milk under HTST processing conditions is needed. This study was undertaken to identify combinations and concentrations of biocides that can inactivate B. anthracis spores at temperatures in the HTST range in less than 1 min. Hydrogen peroxide (HP), sodium hypochlorite (SH), and peroxyacetic acid (PA) were evaluated for their efficacy in inactivating spores of strains 7702, ANR-1, and 9131 in milk at 72, 80, and 85°C using a sealed capillary tube technique. Strains ANR-1 and 9131 were more resistant to all of the biocide treatments than strain 7702. Addition of 1,260 ppm SH to milk reduced the number of viable spores of each strain by 6 log CFU/ml in less than 90 and 60 s at 72 and 80°C, respectively. After neutralization, 1,260 ppm SH reduced the time necessary to inactivate 6 log CFU/ml (TTI6-log) at 80°C to less than 20 s. Treatment of milk with 7,000 ppm HP resulted in a similar level of inactivation in 60 s. Combined treatment with 1,260 ppm SH and 1,800 ppm HP inactivated spores of all strains in less than 20 s at 80°C. Mixing 15 ppm PA with milk containing 1,260 ppm SH resulted in TTI6-log of 25 and 12 s at 72 and 80°C, respectively. TTI6-log of less than 20 s were also achieved at 80°C by using two combinations of biocides: 250 ppm SH, 700 ppm HP, and 150 ppm PA; and 420 ppm SH (pH 7), 1,100 ppm HP, and 15 ppm PA. These results indicated that different combinations of biocides could consistently result in 6-log reductions in the number of B. anthracis spores in less than 1 min at temperatures in the HTST range. This information could be useful for developing more effective thermal treatment strategies which could be used in HTST milk plants to process contaminated milk for disposal and decontamination, as well as for potential protective measures. PMID:18390680

Inactivation of Bacillus anthracis spores by a combination of biocides and heating under high-temperature short-time pasteurization conditions.

PubMed

Xu, Sa; Labuza, Theodore P; Diez-Gonzalez, Francisco

2008-06-01

The milk supply is considered a primary route for a bioterrorism attack with Bacillus anthracis spores because typical high-temperature short-time (HTST) pasteurization conditions cannot inactivate spores. In the event of intentional contamination, an effective method to inactivate the spores in milk under HTST processing conditions is needed. This study was undertaken to identify combinations and concentrations of biocides that can inactivate B. anthracis spores at temperatures in the HTST range in less than 1 min. Hydrogen peroxide (HP), sodium hypochlorite (SH), and peroxyacetic acid (PA) were evaluated for their efficacy in inactivating spores of strains 7702, ANR-1, and 9131 in milk at 72, 80, and 85 degrees C using a sealed capillary tube technique. Strains ANR-1 and 9131 were more resistant to all of the biocide treatments than strain 7702. Addition of 1,260 ppm SH to milk reduced the number of viable spores of each strain by 6 log CFU/ml in less than 90 and 60 s at 72 and 80 degrees C, respectively. After neutralization, 1,260 ppm SH reduced the time necessary to inactivate 6 log CFU/ml (TTI6-log) at 80 degrees C to less than 20 s. Treatment of milk with 7,000 ppm HP resulted in a similar level of inactivation in 60 s. Combined treatment with 1,260 ppm SH and 1,800 ppm HP inactivated spores of all strains in less than 20 s at 80 degrees C. Mixing 15 ppm PA with milk containing 1,260 ppm SH resulted in TTI6-log of 25 and 12 s at 72 and 80 degrees C, respectively. TTI6-log of less than 20 s were also achieved at 80 degrees C by using two combinations of biocides: 250 ppm SH, 700 ppm HP, and 150 ppm PA; and 420 ppm SH (pH 7), 1,100 ppm HP, and 15 ppm PA. These results indicated that different combinations of biocides could consistently result in 6-log reductions in the number of B. anthracis spores in less than 1 min at temperatures in the HTST range. This information could be useful for developing more effective thermal treatment strategies which could be used in HTST milk plants to process contaminated milk for disposal and decontamination, as well as for potential protective measures.

Magnetically Separable MoS₂/Fe₃O₄/nZVI Nanocomposites for the Treatment of Wastewater Containing Cr(VI) and 4-Chlorophenol.

PubMed

Lu, Haijiao; Wang, Jingkang; Hao, Hongxun; Wang, Ting

2017-09-30

With a large specific surface area, high reactivity, and excellent adsorption properties, nano zerovalent iron (nZVI) can degrade a wide variety of contaminants in wastewater. However, aggregation, oxidation, and separation issues greatly impede its wide application. In this study, MoS₂/Fe₃O₄/nZVI nanocomposites were successfully synthesized by a facile step-by-step approach to overcome these problems. MoS₂ nanosheets (MNs) acted as an efficient support for nZVI and enriched the organic pollutants nearby, leading to an enhanced removal efficiency. Fe₃O₄ nanoparticles (NPs) could not only suppress the agglomeration and restacking of MNs, but also facilitate easy separation and recovery of the nanocomposites. The synergistic effect between MNs and Fe₃O₄ NPs effectively enhanced the reactivity and efficiency of nZVI. In the system, Cr(VI) was reduced to Cr(III) by nZVI in the nanocomposites, and Fe 2+ produced in the process was combined with H₂O₂ to further remove 4-Chlorophenol (4-CP) through a Fenton reaction. Furthermore, the nanocomposites could be easily separated from wastewater by a magnet and be reused for at least five consecutive runs, revealing good reusability. The results demonstrate that the novel nanocomposites are highly efficient and promising for the simultaneous removal of Cr(VI) and 4-CP in wastewater.

[Using Excess Activated Sludge Treated 4-Chlorophenol Contained Waste Water to Cultivate Chlorella vulgaris].

PubMed

Wang, Lu; Chen, Xiu-rong; Yan, Long; He, Yi-xuan; Shi, Zhen-dong

2015-04-01

Using different rations of sludge extracts and supernate from 4-Chlorophenol (4-CP) simulated wastewater's excess sludge after centrifugation to cultivate the Chlorella vulgaris to achieve the goal of excess sludge utilization together with chlorella cultivating. The experiments were performed in 500 mL flasks with different rations of sludge extracts & BG-11 and supernate & BG-11 in a light growth chamber respectively. Number of algal cells, Chlorophyll, enzyme activity, oil and water total nitrogen (TN), total phosphorus (TP), total organic carbon (TOC), toxicity index were investigated. Result showed that the nutrition supplies and toxicity in the excess sludge were removed efficiently via Chlorella vulgaris, the removal rates of TN and TP were at least 40% and 90% respectively; After 10 days cultivation, the density growth of 50% sludge extracts was 20 times higher of the beginning while its chlorophyll content was lower than that of the blank group. Sludge extracts could promote the proliferation of algae, but were not conducive to the synthesis of chlorophyll. The quantity of SOD in per cell showed Chlorella vulgaris gave a positive response via stimulation from toxicant in sludge extracts and supernate. The best time for collecting chlorella vulgaris was the fifth day of cultivation, taking neutral oil accumulation as the evaluating indicator for its utilization combined with the removal of supplies and toxicity.

Alkyl ammonium cation stabilized biocidal polyiodides with adaptable high density and low pressure.

PubMed

He, Chunlin; Parrish, Damon A; Shreeve, Jean'ne M

2014-05-26

The effective application of biocidal species requires building the active moiety into a molecular back bone that can be delivered and decomposed on demand under conditions of low pressure and prolonged high-temperature detonation. The goal is to destroy storage facilities and their contents while utilizing the biocidal products arising from the released energy to destroy any remaining harmful airborne agents. Decomposition of carefully selected iodine-rich compounds can produce large amounts of the very active biocides, hydroiodic acid (HI) and iodine (I2). Polyiodide anions, namely, I3(-), I5(-), which are excellent sources of such biocides, can be stabilized through interactions with large, symmetric cations, such as alkyl ammonium salts. We have designed and synthesized suitable compounds of adaptable high density up to 3.33 g cm(-3) that are low-pressure polyiodides with various alkyl ammonium cations, deliverable iodine contents of which range between 58.0-90.9%. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evaluation of antibiofilm effect of benzalkonium chloride, iodophore and sodium hypochlorite against biofilm of Pseudomonas aeruginosa of dairy origin.

PubMed

Pagedar, Ankita; Singh, Jitender

2015-08-01

The present study was undertaken with objectives of; a) to investigate and compare Pseudomonas aeruginosa isolates from two dairies for biofilm formation potential and, b) to compares three common biocides for biofilm eradication efficiencies. Amongst the isolates from commercial dairy, 70 % were strong and/or moderate biofilm former in comparison to 40 % isolates from small scale dairy. All isolates, irrespective of source, exhibited higher susceptibility to biocides in planktonic stage than in biofilm. Antibiofilm efficiencies of three biocides i.e. benzalkonium chloride, sodium hypochlorite and iodophore were determined in terms of their microbial biofilms eradicating concentration (MBEC). Our findings show that the three biocides were ineffective against preformed biofilms at recommended in-use concentrations. Biofilms were the most resistant to benzalkonium chloride and least against iodophore. A trend of decreasing MBECs was observed with extended contact time. The findings of present study warrant for a systematic approach for selecting types and concentrations of biocide for application as antibiofilm agent in food industry.

The use of poloxamer hydrogels for the assessment of biofilm susceptibility towards biocide treatments.

PubMed

Gilbert, P; Jones, M V; Allison, D G; Heys, S; Maira, T; Wood, P

1998-12-01

Poloxamer F127 is a non-toxic, di-block copolymer of polyoxyethylene and polyoxypropylene. Aqueous solutions (30% w/v) show thermoreversible gelation, being liquid at temperatures < 15 degrees C and robust gels at temperatures > 15 degrees C. Chilled poloxamer (30% in tryptone soya broth) was mixed with an inoculum of Pseudomonas aeruginosa (10(4) cfu ml-1) and placed as 100 microliters drops onto separate glass cover-slips. These were placed into sealed Petri dishes containing moistened cotton wool and incubated at 35 degrees C. Viable counts could be performed on the poloxamer gels by transfer of the coverslips to diluents at < 15 degrees C. Growth curves in the gels and in liquid batch cultures were indistinguishable from one another with stationary phase cell densities, being approximately 5 x 10(10) cfu ml-1 in each at 16 h. SDS-PAGE of cell envelope preparations showed the poloxamer-grown cells to exhibit a biofilm rather than planktonic phenotype. Susceptibility towards various concentrations of chlorhexidine, iodine and hydrogen peroxide was assessed for 10 min at 35 degrees C for suspensions of broth-grown cells and for incubated poloxamer-gels (1 and 16 h). The gels were immersed in biocide, on their glass supports, before transfer to neutralizer at 10 degrees C where dissolution was complete within 5 min. Further serial dilutions and plate counts were made. While modest decreases in susceptibility towards all biocides were associated with incorporation of the inoculum with the gel (1 h incubation), substantial changes were noted after prolonged incubation and adaptation to a biofilm phenotype (16 h incubation). The gel populations mimic the localized high cell densities observed in biofilms and will also be subject to the same nutrient and chemical gradients as found within natural biofilms. Thermoreversible gelation enables complete recovery of the test inoculum without further trauma. They therefore provide an effective model for assessing biofilm susceptibility towards biocides and would be suitable for screening programmes.

Spectrum of the Reductive Dehalogenation Activity of Desulfitobacterium frappieri PCP-1

PubMed Central

Dennie, D.; Gladu, I.; Lépine, F.; Villemur, R.; Bisaillon, J.-G.; Beaudet, R.

1998-01-01

Desulfitobacterium frappieri PCP-1 was induced for ortho- and para-dechlorinating activities by different chlorophenols. Dehalogenation rates ranging from 25 to 1,158 nmol/min/mg of cell protein were observed according to the chlorophenol tested and the position of the chlorine removed. D. frappieri shows a broad substrate specificity; in addition to tetrachloroethylene and pentachloropyridine, strain PCP-1 can dehalogenate at ortho, meta, and para positions a large variety of aromatic molecules with substituted hydroxyl or amino groups. Reactions of O demethylation and reduction of nitro to amino substituents on aromatic molecules were also observed. PMID:9797330

Adsorptive removal of 2-chlorophenol by low-cost coir pith carbon.

PubMed

Namasivayam, C; Kavitha, D

2003-03-17

Adsorption of 2-chlorophenol (2-CP) by coir pith carbon was carried out by varying the parameters such as agitation time, 2-CP concentration, adsorbent dose, pH and temperature. Adsorption equilibrium reached at 40, 60, 80 and 100 min for 2-CP concentration of 10, 20, 30 and 40 mg/l, respectively. Adsorption followed second-order kinetics. The adsorption equilibrium data obeyed Freundlich isotherm. Acidic pH was favorable for the adsorption of 2-CP. Desorption studies showed that chemisorption plays a major role in the adsorption process. Copyright 2003 Elsevier Science B.V.

Does microbial resistance to biocides create a hazard to food hygiene?

PubMed

Meyer, Bernhard

2006-12-01

Numerous reports are available on microbial resistance to antibiotics as well as to biocides. Instances of cross-resistance between these substance groups have been reported. Resistance, which is a genetically determined phenomenon, has to be distinguished from phenotypic adaptation processes, which are not hereditary. Adaptation can be avoided by rigorous cleaning and disinfection, avoiding concentrations of disinfectants below the microbicidal concentration. Resistance phenomena have to be divided into intrinsic and acquired resistance. Intrinsic resistance is the naturally greater resistance of certain microbial species compared to others. The term acquired resistance is used if certain strains of a microbial species differ significantly in their susceptibility to biocides compared to the average of this species. An overview of existing reports of resistance to different biocidal substances is given. In most of these reports, resistance is defined as an elevated minimum inhibitory concentration. The relevance of these data for disinfection processes, where microbicidal concentrations are applied, is discussed. Rotational use of different types of disinfectants, to avoid development of resistance, has been discussed controversially. Because of the unspecific mechanism of action of biocides, and the lack of scientific evidence for its need, rotational use of disinfectants is not recommended. In conclusion the risk of hazards in food production and processing caused by resistance to biocides is regarded as low.

Biocide and antibiotic resistance of Enterococcus faecalis and Enterococcus faecium isolated from the swine meat chain.

PubMed

Rizzotti, Lucia; Rossi, Franca; Torriani, Sandra

2016-12-01

In this study nine strains of Enterococcus faecalis and 12 strains of Enterococcus faecium, isolated from different sample types in the swine meat chain and previously characterized for the presence of antibiotic resistance genes, were examined for phenotypic tolerance to seven biocides (chlorexidine, benzalkonium chloride, triclosan, sodium hypochlorite, 2-propanol, formaldehyde and hydrogen peroxide) and resistance to nine antibiotics (ampicillin, vancomycin, gentamicin, kanamycin, streptomycin, erythromycin, clindamycin, tetracycline and chloramphenicol). Moreover, the presence of efflux system encoding genes qacA/B, qacC, qacE, qacEΔ1, emeA, and stress response genes, sigV and gsp65, involved in the tolerance to biocides, was analysed. Most strains were not tolerant to the biocides, but showed minimum inhibitory concentrations (MICs) higher than the recommended cut-off values for all the antibiotics tested, except for vancomycin and chloramphenicol. Only weak correlations, if any, were found between biocide and antibiotic resistance data. One E. faecalis strain was tolerant to triclosan and one E. faecium strain, with higher tolerance to chlorexidine than the other strains tested, was found to carry a qacA/B gene. Our results indicated that phenotypic resistance to antibiotics is very frequent in enterococcal isolates from the swine meat chain, but phenotypic tolerance to biocides is not common. On the other hand, the gene qacA/B was found for the first time in the species E. faecium, an indication of the necessity to adopt measures suitable to control the spread of biocide resistance determinants among enterococci. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of Antifouling Biocides on Molecular and Biochemical Defense System in the Gill of the Pacific Oyster Crassostrea gigas

PubMed Central

Park, Mi Seon; Kim, Young Dae; Kim, Bo-Mi; Kim, Youn-Jung; Kim, Jang Kyun; Rhee, Jae-Sung

2016-01-01

Antifouling biocides such as organotin compounds and their alternatives are potent toxicants in marine ecosystems. In this study, we employed several molecular and biochemical response systems of the Pacific oyster Crassostrea gigas to understand a potential mode of action of antifouling biocides (i.e. tributyltin (TBT), diuron and irgarol) after exposure to different concentrations (0.01, 0.1, and 1 μg L-1) for 96 h. As a result, all the three antifouling biocides strongly induced the antioxidant defense system. TBT reduced both enzymatic activity and mRNA expression of Na+/K+-ATPase and acetylcholinesterase (AChE). Lower levels of both Na+/K+-ATPase activity and AChE mRNA expression were observed in the diuron-exposed oysters compared to the control, while the irgarol treatment reduced only the transcriptional expression of AChE gene. We also analyzed transcript profile of heat shock protein (Hsp) superfamily in same experimental conditions. All antifouling biocides tested in this study significantly modulated mRNA expression of Hsp superfamily with strong induction of Hsp70 family. Taken together, overall results indicate that representative organotin TBT and alternatives have potential hazardous effects on the gill of C. gigas within relatively short time period. Our results also suggest that analyzing a series of molecular and biochemical parameters can be a way of understanding and uncovering the mode of action of emerging antifouling biocides. In particular, it was revealed that Pacific oysters have different sensitivities depend on the antifouling biocides. PMID:28006823

Ecotoxicological potential of the biocides terbutryn, octhilinone and methylisothiazolinone: Underestimated risk from biocidal pathways?

PubMed

Kresmann, Simon; Arokia, Arokia Hansel Rajan; Koch, Christoph; Sures, Bernd

2018-06-01

The use of biocides by industry, agriculture and households increased throughout the last two decades. Many new applications with known substances enriched the variety of biocidal pollution sources for the aquatic environment. While agriculture was the major source for a long time, leaching from building facades and preservation of personal care and cleaning products was identified as new sources in the last few years. With the different usage forms of biocidal products the complexity of legislative regulation increased as well. The requirements for risk assessment differ from one law to another and the potential risk of substances under different regulations might be underestimated. Still EC 50 and predicted no-effect concentration (PNEC) values gained from testing with different species are the core of environmental risk assessment, but ecotoxicological data is limited or lacking for many biocides. In this study the biocides widely used in facade coatings and household products terbutryn, octhilinone and methylisothiazolinone were tested with the Daphnia magna acute immobilisation assay, the neutral red uptake assay and the ethoxyresorufin-O-deethylase (EROD) assay, performed with rainbow trout liver (RTL-W1) cells. Further, the MTT assay with the ovarian cell line CHO-9 from Chinese hamster was used as mammalian model. Octhilinone induced the strongest effects with EC 50 values of 156μg/l in the D. magna assay, while terbutryn showed the weakest effects with 8390μg/l and methylisothiazolinone 513μg/l respectively. All other assays showed higher EC 50 values and thus only weak effects. EROD assays did not show any effects. With additional literature and database records PNEC values were calculated: terbutryn reached 0.003μg/l, octhilinone 0.05μg/l and methylisothiazolinone 0.5μg/l. Potential ecotoxicological risks of these biocides are discussed, considering environmental concentrations. Copyright © 2017 Elsevier B.V. All rights reserved.

Preparation, bioactivity, and application of novel biocidal materials

NASA Astrophysics Data System (ADS)

Wu, Rong

In this study, several novel N-halamine precursors were synthesized. These surface coupling agents were bonded to the surfaces of cotton fabric, cotton gauze, paper, glass, and sand. Once they were activated using household bleach, the surfaces and materials became biocidal. Possible uses for the biocidal cotton are in protective garments for hospital personnel and those who must fight against bioterrorism. The treated cotton gauze may be used to make an antimicrobial mask to stop infective pathogen transcontamination. Biocidal sand has the potential to be used as a disinfectant in a filter for wastewater or municipal water treatment. In fact, the N-halamine siloxanes can be applied to many other surfaces. The results of biocidal efficacy of some of the treated surfaces will be presented in this study. Several new hydantoinyl diols and quaternary ammonium hydantoinyl diols were prepared in this work also. They were copolymerized with commercial water borne acrylic polyol and commercial isocyanate to form polyurethane coatings. The biocidal polyurethane coatings were produced after activation by chlorination. Those diols also reacted with a two-component epoxy paint to render the paint antimicrobial. Several novel biocidal polymeric resins were synthesized by attachment of N-halamine moieties to the commercial polymer supported beads such as Merrifield resin and Amberlite IRA-67 ionic resin. The Merrifield resin and Amberlite IRA-67 ionic resin also were grafted with N-halamine functionality as well as with the N,N-dimethyl-dodecylamine moiety via 1,2-dichloroethane. Finally, several quaternary ammonium N-halamine polymers were prepared. Direct copolymerization of (triethoxysilyl)propyl-7,7,9,9-tetramethyl-1,3,8-triazaspiro-[4,5]-decane-2,4-dione (TTDD-Si), or 3-(trimethoxysilyl)propyl-5,5-dimethylhydantoin (BA-1 ') with 3-(trimethoxysilylpropyl)dimethyloctadecyl ammonium chloride (DC 5700) produced dual functionality and water soluble biocidal materials and surfaces. (Abstract shortened by UMI.)

Regenerable biocide delivery unit, volume 1

NASA Technical Reports Server (NTRS)

Atwater, James E.; Wheeler, Richard R., Jr.

1992-01-01

The Microbial Check Valve (MCV), which is currently used aboard the Shuttle Orbiter for disinfection of the potable water supply, is an expendable flow-through canister containing iodinated ion exchange resin. Means for extension of MCV life are desirable to avoid resupply penalties. The Phase 1 Regenerable Biocide Delivery Unit program demonstrated the feasibility of regenerating an MCV in situ, using a strong aqueous elemental iodine solution resulting from diversion of the MCV influent to a packed bed containing iodine crystals. In small column tests, eight manual regenerations of an MCV resin were accomplished. The term Regenerative Microbial Check Valve (RMCV) was adopted describing this new technology. The Phase 2 program resulted in the development of a full scale and fully autonomous prototype RMCV, capable of maintaining residual I(sub 2) levels between 2.0 - 4.0 mg/L for prolonged periods. During six months of testing at the Space Station baseline flow rate of 120 cm(sup 3)/min, the prototype RMCV underwent nine regenerations. RMCV life cycle tests, using a variety of influent streams, were conducted over an eighteen month period to determine the useful lives of MCV's incorporating this new technology and to determine ultimate failure mechanisms. MCV life extensions of 130 fold were demonstrated, limited only by the Phase 2 performance period. Based upon this work, it is certain that RMCV units can be developed to provide unattended biocide addition for the thirty year life of Space Station Freedom, or for other longer duration applications such as a Lunar Base or Mars mission. RMCV technology was also demonstrated capable of delivering, on demand, a concentrated aqueous I(sub 2) solution for potential use as a disinfectant during transient episodes of microbial surface contamination, for the control of biofilm formation, or as a preventative measure in systems which are particularly susceptible to the growth of microorganisms.

Does antifouling paint select for antibiotic resistance?

PubMed

Flach, Carl-Fredrik; Pal, Chandan; Svensson, Carl Johan; Kristiansson, Erik; Östman, Marcus; Bengtsson-Palme, Johan; Tysklind, Mats; Larsson, D G Joakim

2017-07-15

There is concern that heavy metals and biocides contribute to the development of antibiotic resistance via co-selection. Most antifouling paints contain high amounts of such substances, which risks turning painted ship hulls into highly mobile refuges and breeding grounds for antibiotic-resistant bacteria. The objectives of this study were to start investigate if heavy-metal based antifouling paints can pose a risk for co-selection of antibiotic-resistant bacteria and, if so, identify the underlying genetic basis. Plastic panels with one side painted with copper and zinc-containing antifouling paint were submerged in a Swedish marina and biofilms from both sides of the panels were harvested after 2.5-4weeks. DNA was isolated from the biofilms and subjected to metagenomic sequencing. Biofilm bacteria were cultured on marine agar supplemented with tetracycline, gentamicin, copper sulfate or zinc sulfate. Biofilm communities from painted surfaces displayed lower taxonomic diversity and enrichment of Gammaproteobacteria. Bacteria from these communities showed increased resistance to both heavy metals and tetracycline but not to gentamicin. Significantly higher abundance of metal and biocide resistance genes was observed, whereas mobile antibiotic resistance genes were not enriched in these communities. In contrast, we found an enrichment of chromosomal RND efflux system genes, including such with documented ability to confer decreased susceptibility to both antibiotics and biocides/heavy metals. This was paralleled by increased abundances of integron-associated integrase and ISCR transposase genes. The results show that the heavy metal-based antifouling paint exerts a strong selection pressure on marine bacterial communities and can co-select for certain antibiotic-resistant bacteria, likely by favoring species and strains carrying genes that provide cross-resistance. Although this does not indicate an immediate risk for promotion of mobile antibiotic resistance, the clear increase of genes involved in mobilizing DNA provides a foundation for increased opportunities for gene transfer in such communities, which might also involve yet unknown resistance mechanisms. Copyright © 2017 Elsevier B.V. All rights reserved.

Antimicrobial Activity of Chitosan Derivatives Containing N-Quaternized Moieties in Its Backbone: A Review

PubMed Central

Martins, Alessandro F.; Facchi, Suelen P.; Follmann, Heveline D. M.; Pereira, Antonio G. B.; Rubira, Adley F.; Muniz, Edvani C.

2014-01-01

Chitosan, which is derived from a deacetylation reaction of chitin, has attractive antimicrobial activity. However, chitosan applications as a biocide are only effective in acidic medium due to its low solubility in neutral and basic conditions. Also, the positive charges carried by the protonated amine groups of chitosan (in acidic conditions) that are the driving force for its solubilization are also associated with its antimicrobial activity. Therefore, chemical modifications of chitosan are required to enhance its solubility and broaden the spectrum of its applications, including as biocide. Quaternization on the nitrogen atom of chitosan is the most used route to render water-soluble chitosan-derivatives, especially at physiological pH conditions. Recent reports in the literature demonstrate that such chitosan-derivatives present excellent antimicrobial activity due to permanent positive charge on nitrogen atoms side-bonded to the polymer backbone. This review presents some relevant work regarding the use of quaternized chitosan-derivatives obtained by different synthetic paths in applications as antimicrobial agents. PMID:25402643

Electrochemical treatment of aqueous solutions of organic pollutants by electro-Fenton with natural heterogeneous catalysts under pressure using Ti/IrO2-Ta2O5 or BDD anodes.

PubMed

Ltaïef, Aziza Hadj; Sabatino, Simona; Proietto, Federica; Ammar, Salah; Gadri, Abdellatif; Galia, Alessandro; Scialdone, Onofrio

2018-07-01

The treatment of toxic organic pollutants by electro-Fenton (EF) presents some drawbacks such as the necessity to work at low pH and the low solubility of oxygen in water contacted with air or oxygen at room pressure that results often in slow and relatively low abatements. Here, the coupled adoption of natural heterogeneous catalysts and of relatively high pressure was proposed in order to improve the performances of EF for the treatment of organic pollutants. Caffeic acid (CA) and 3-chlorophenol were used as model resistant organic pollutants. EF process was performed using both conventional homogeneous FeSO 4 and natural heterogeneous catalysts (pyrite, chalcopyrite, Fe 2 O 3 and Fe 3 O 4 ) as iron catalysts and oxygen at various pressures in the absence or in the presence of BDD anode. The effect of the nature of the catalyst, the oxygen pressure, the current density and the catalyst load was widely investigated in order to optimize the process. It was shown that the coupled utilization of a natural heterogeneous catalyst such as chalcopyrite and a relatively high pressure allows to obtain the total removal of CA and a high removal of the TOC (about 75%) in short times (2 h) with relatively high current efficiencies using an Iridium based anode. In the case of 3-chlorophenol, the utilization of a BDD anode was necessary to achieve a high removal of the pollutant and the TOC. It was shown that the removal of 3-chlorophenol can be effectively performed in different water bodies and with different initial concentrations of 3-chlorophenol. Copyright © 2018 Elsevier Ltd. All rights reserved.

Antimicrobial efficacy of a novel eucalyptus oil, chlorhexidine digluconate and isopropyl alcohol biocide formulation.

PubMed

Hendry, Emma; Conway, Barbara; Worthington, Tony

2012-10-30

Effective surface disinfection is a fundamental infection control strategy within healthcare. This study assessed the antimicrobial efficacy of novel biocide formulations comprising 5% and 2% eucalyptus oil (EO) combined with 2% chlorhexidine digluconate (CHG) and 70% isopropyl alcohol (IPA) contained within a wipe. The efficacy of this novel antimicrobial formulation to remove and eliminate methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli and Candida albicans from steel surfaces was investigated. Adpression studies of pre-contaminated wipes were also utilised to assess their potential to induce cross-contamination between hard surfaces. Furthermore, the bactericidal nature of the EO-formulation was established in addition to time-kill. The EO-containing formulations demonstrated bactericidal antimicrobial efficacy against all microorganisms and did not induce surface cross-contamination. There was no significant difference (p < 0.05) between the 5% and 2% EO formulations in their ability to remove microorganisms from steel surfaces, however both significantly (p < 0.05) removed more than the control formulations. Microbial biofilms were eliminated within 10 min (p < 0.05) when exposed to the EO formulations. Our novel EO-formulation demonstrated rapid antimicrobial efficacy for potential disinfection and elimination of microbial biofilms from hard surfaces and may therefore be a useful adjunct to current infection control strategies currently employed within healthcare facilities.

Antimicrobial Efficacy of a Novel Eucalyptus Oil, Chlorhexidine Digluconate and Isopropyl Alcohol Biocide Formulation

PubMed Central

Hendry, Emma; Conway, Barbara; Worthington, Tony

2012-01-01

Effective surface disinfection is a fundamental infection control strategy within healthcare. This study assessed the antimicrobial efficacy of novel biocide formulations comprising 5% and 2% eucalyptus oil (EO) combined with 2% chlorhexidine digluconate (CHG) and 70% isopropyl alcohol (IPA) contained within a wipe. The efficacy of this novel antimicrobial formulation to remove and eliminate methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli and Candida albicans from steel surfaces was investigated. Adpression studies of pre-contaminated wipes were also utilised to assess their potential to induce cross-contamination between hard surfaces. Furthermore, the bactericidal nature of the EO-formulation was established in addition to time-kill. The EO-containing formulations demonstrated bactericidal antimicrobial efficacy against all microorganisms and did not induce surface cross-contamination. There was no significant difference (p < 0.05) between the 5% and 2% EO formulations in their ability to remove microorganisms from steel surfaces, however both significantly (p < 0.05) removed more than the control formulations. Microbial biofilms were eliminated within 10 min (p < 0.05) when exposed to the EO formulations. Our novel EO-formulation demonstrated rapid antimicrobial efficacy for potential disinfection and elimination of microbial biofilms from hard surfaces and may therefore be a useful adjunct to current infection control strategies currently employed within healthcare facilities. PMID:23203047

Mixture toxicity of wood preservative products in the fish embryo toxicity test.

PubMed

Coors, Anja; Dobrick, Jan; Möder, Monika; Kehrer, Anja

2012-06-01

Wood preservative products are used globally to protect wood from fungal decay and insects. We investigated the aquatic toxicity of five commercial wood preservative products, the biocidal active substances and some formulation additives contained therein, as well as six generic binary mixtures of the active substances in the fish embryo toxicity test (FET). Median lethal concentrations (LC50) of the single substances, the mixtures, and the products were estimated from concentration-response curves and corrected for concentrations measured in the test medium. The comparison of the experimentally observed mixture toxicity with the toxicity predicted by the concept of concentration addition (CA) showed less than twofold deviation for all binary mixtures of the active substances and for three of the biocidal products. A more than 60-fold underestimation of the toxicity of the fourth product by the CA prediction was detected and could be explained fully by the toxicity of one formulation additive, which had been labeled as a hazardous substance. The reason for the 4.6-fold underestimation of toxicity of the fifth product could not be explained unambiguously. Overall, the FET was found to be a suitable screening tool to verify whether the toxicity of formulated wood preservatives can reliably be predicted by CA. Applied as a quick and simple nonanimal screening test, the FET may support approaches of applying component-based mixture toxicity predictions within the environmental risk assessment of biocidal products, which is required according to European regulations. Copyright © 2012 SETAC.

ZnO and ZnTiO3 nanopowders for antimicrobial stone coating

NASA Astrophysics Data System (ADS)

Ruffolo, S. A.; La Russa, M. F.; Malagodi, M.; Oliviero Rossi, C.; Palermo, A. M.; Crisci, G. M.

2010-09-01

In the past a great variety of biocidal compounds and persistent organic pesticides were applied on a large scale for preventive measures aimed at the long-term preservation of our cultural heritage. Only recently, public and expert attention has started to focus increasingly on the risks resulting from these treatments on human health, works of art and environment in general. The work done in this field demonstrated that the most effective way for inactivation can be achieved by using highly efficient photocatalysts with the illumination of UV radiation. Following this direction our group focused its attention on well-known photocatalysts, ZnO and ZnTiO3, in the degradation and complete mineralisation of environmental pollutants. This explorative work deals with an experimental investigation on biocidal efficient of ZnO and ZnTiO3. In particular micro-quantities of the two nanopowdered photocatalysts were spread on plated dishes. They were filled by the MEA (Malt Extract Agar) medium containing given quantities of Aspergillus Niger (a chromogen filamentous fungus involved in biodeterioration). At the same time the two oxides were dispersed in different polymeric matrices, acrylic and fluorinated, in order to obtain a new coating technology, with hydrophobic, consolidant and biocidal properties for the restoration of building stone material. The mixtures obtained were applied on marble samples and capillary water absorption, simulated solar ageing, colourimetric measurements and contact angle measurements have been performed to evaluate its properties.

Efficacy and Ecotoxicity of Novel Anti-Fouling Nanomaterials in Target and Non-Target Marine Species.

PubMed

Avelelas, Francisco; Martins, Roberto; Oliveira, Tânia; Maia, Frederico; Malheiro, Eliana; Soares, Amadeu M V M; Loureiro, Susana; Tedim, João

2017-04-01

Biofouling is a global problem that affects virtually all the immersed structures. Currently, several novel environmentally friendly approaches are being tested worldwide to decrease the toxicity of biocides in non-fouling species, such as the encapsulation/immobilization of commercially available biocides, in order to achieve control over the leaching rate. The present study addresses the toxicity of two widely used booster biocides, zinc pyrithione (ZnPT) and copper pyrithione (CuPT), in its free and incorporated forms in order to assess their toxicity and anti-fouling efficacy in target and non-target species. To achieve this goal, the following marine organisms were tested; the green microalgae Tetraselmis chuii (non-target species) and both target species, the diatom Phaeodactylum tricornutum and the mussel Mytilus edulis. Organisms were exposed to both biocides, two unloaded nanostructured materials and nanomaterials loaded with biocides, from 10 μg/L to 100 mg/L total weight, following standard protocols. The most eco-friendly and simultaneously efficient anti-fouling solution against the two photosynthetic species (nanoclays loaded with ZnPT) was then tested on mussels to assess its lethal efficacy (LC 50  = 123 μg/L) and compared with free biocide (LC 50  = 211 μg/L) and unloaded material (LC 50  > 1000 μg/L). A second exposure test with sub-lethal concentrations (lower than 100 μg/L), using mussels, was carried out to assess biochemical changes caused by the tested compounds. Oxidative stress, detoxification and neurotransmission markers were not responsive; however, different antioxidant patterns were found with free ZnPT and loaded nanoclay exposures. Thus, the immobilization of the biocide ZnPT into nanoclays proved to be a promising efficient and eco-friendly anti-fouling strategy.

Use of a predictive protocol to measure the antimicrobial resistance risks associated with biocidal product usage.

PubMed

Wesgate, Rebecca; Grasha, Pierre; Maillard, Jean-Yves

2016-04-01

In this study we assessed the propensity of biocide exposure in the development of antimicrobial resistance in bacteria. Our protocol is based on reporting changes in established antimicrobial susceptibility profiles in biocides and antibiotics after during use exposure to a product. The during use exposure reflects worse conditions of product use during application. It differs from the term low concentration, which usually reflects a concentration below the minimal inhibitory concentration, but not necessarily a concentration that occurs in practice. Our results showed that exposure to triclosan (0.0004%) was associated with a high risk of developing resistance and cross-resistance in Staphylococcus aureus and Escherichia coli. This was not observed with exposure to chlorhexidine (0.00005%) or a hydrogen peroxide-based biocidal product (in during use conditions). Interestingly, exposure to a low concentration of hydrogen peroxide (0.001%) carried a risk of emerging resistance to antibiotics if the presence of the oxidizing agent was maintained. We observed a number of unstable clinical resistances to antibiotics after exposure to the cationic biocide and oxidizing agent, notably to tobramycin and ticarcillin-clavulanic acid. Using a decision tree based on the change in antimicrobial susceptibility test results, we were able to provide information on the effect of biocide exposure on the development of bacterial resistance to antimicrobials. Such information should address the call from the U.S. Food and Drug Administration and European Union Biocidal Products Regulation for manufacturers to provide information on antimicrobial resistance and cross-resistance in bacteria after the use of their product. Copyright © 2016 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Determination of biocides as well as some biocide metabolites from facade run-off waters by solid phase extraction and high performance liquid chromatographic separation and tandem mass spectrometry detection.

PubMed

Bester, K; Lamani, X

2010-08-06

Biocides are used to protect buildings, boats, and other materials from microbial infestations. A huge variety of compounds are being used: isothiazolinones, e.g., to prevent bacterial growth in paints, triazines and phenylureas against algal growth on water exposed materials while carbamates are used against fungal investations. However these biocides can be leached from the respective materials. As these are very effective compounds it is important to know the concentrations of these biocides in the leachates as well as their leaching behaviour to assess their risk to the environment. In this study, a method for the determination of biocides from facade material run-off water by means of high performance liquid chromatography coupled to tandem mass spectrometry (HPLC-MS/MS) was developed. Due to the amphiphilic character and the expected varying pH-values in the samples, the extractions as well as the HPLC-method development proved to be demanding. The water samples (leachates) were buffered with a phosphate buffer to pH 7. As some of the biocides are very hydrophilic, different SPE cartridges were tested to identify the SPE material with the highest recovery rates for all compounds. For gaining a good separation, analyte trapping was performed on the HPLC column. Quantification was performed using a mass spectrometer in multi-reaction monitoring with two transitions per compound. The final recovery rates were conducted using a cartridge with a divenylbenzyl polymer sorbent. A combination of methanol and acetonitrile as eluents was used to reach recovery rates in the range of 70-100%. The limit of quantification for the compounds of interest ranged from 0.01 to 0.1 microg/L. Copyright 2010 Elsevier B.V. All rights reserved.

Biocide and antibiotic susceptibility of Salmonella isolates obtained before and after cleaning at six Danish pig slaughterhouses.

PubMed

Gantzhorn, Mette Rørbæk; Pedersen, Karl; Olsen, John Elmerdahl; Thomsen, Line Elnif

2014-07-02

Salmonella sp. continues to be one of the most important foodborne pathogens. Control measures in terms of cleaning and disinfection on food production plants are very important for limiting the risk of contaminated food products to reach the consumer. In the last decade concern has arisen that bacteria exposed to disinfectants can develop resistance toward disinfectants and can have a higher risk of developing antibiotic resistance. The objectives of this study were to examine the prevalence of biocide resistant Salmonella sp. in Danish pig slaughterhouses, to evaluate if there was a correlation between susceptibilities to biocides and antibiotics, and to examine if cleaning and disinfection select isolates with changed susceptibility toward biocides or antibiotics. Salmonella sp. was isolated from the environment in Danish pig slaughterhouses before and after cleaning and disinfection. The susceptibility toward three different biocides, triclosan and two commercial disinfection products: Desinfect Maxi, a quaternary ammonium compound, and Incimaxx DES, an acetic compound, was determined. We found no resistance toward the biocides tested, but we did find that isolates obtained after cleaning had higher minimum inhibitory concentration (MIC) values toward one of the disinfectants (Incimaxx DES) compared to isolates obtained before cleaning and disinfection. This could indicate selection of strains that are more tolerant, due to the cleaning and disinfection. Furthermore, we found that there was a weak statistical correlation between MICs toward the biocides and some antibiotics, but no difference in log(MIC)s toward antibiotics between isolates obtained before and after cleaning, nor did we find any difference in the number of resistances of isolates obtained before and after cleaning and disinfection. Copyright © 2014 Elsevier B.V. All rights reserved.

The application of bioactive compounds from the food industry to control mold growth in indoor waterborne coatings.

PubMed

Bellotti, N; Salvatore, L; Deyá, C; Del Panno, M T; del Amo, B; Romagnoli, R

2013-04-01

Microbial growth in indoor environments creates health problems, especially in people with asthma; approximately 80% of these patients are allergic to mold. Antimicrobial coatings are formulated to generate surfaces that are easy to clean and may also incorporate active agents, commonly called biocides, which inhibit microbial colonization, subsequent growth and bio-deterioration of the substrates. Some research lines seek to replace traditional organometallic and organochlorines biocides with environmentally acceptable ones. The aim of this research was, primarily, to explore the possible application of different compounds used in food industry like preservatives to be used as antimicrobial additives for antimicrobial coatings. Four biocides were tested against two different ambient molds isolated from an interior painted wall (Chaetomium globosum and Alternaria alternate). The selected biocides were zinc salicylate, zinc benzoate, calcium benzoate and potassium sorbate. The resulting paints were subjected to biological and physical tests (viscosity, hiding power, humidity absorption and biocides leaching rate). Bioassays revealed that zinc benzoate and zinc salicylate resulted active against both fungi. Copyright © 2012 Elsevier B.V. All rights reserved.

Material Testing in Support of the ISS Electrochemical Disinfection Feasibility Study

NASA Technical Reports Server (NTRS)

Clements, Anna; Shindo, David; Modica, Cathy

2011-01-01

The International Space Station Program recognizes the risk of microbial contamination in their potable and non-potable water sources. With the end of the Space Shuttle Program, the ability to send up shock-kits of biocides in the event of an outbreak becomes even more difficult. Currently, the US Segment water system relies primarily on iodine to mitigate contamination concerns. To date, several small cases of contamination have occurred which have been remediated. NASA, however, realizes that having a secondary method of combating a microbial outbreak is a prudent investment. NASA is looking into developing hardware that can generate biocides electrochemically, and potentially deploying that hardware. The specific biocides that the technology could generate include: hydrogen peroxide, oxone, hypochlorite and peracetic acid. In order to use these biocides on deployed water systems, the project must determine that all the materials in the potential application are compatible with the biocides at their anticipated administered concentrations. This paper will detail the materials test portion of the feasibility assessment including the plan for both metals and non-metals along with results to date.

Biocides: Capturing bugs and bigger markets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hairston, D.W.

1995-10-01

Deep in the dark interior of cooling water towers, intake streams and purifiers, there is a jungle. Hundreds of thousands of microorganisms dwell in algae and biofilm, breeding mutant and increasingly resistant strains of bacteria. For biocide manufacturers, the imperative is to find better ways to control the proliferation of the microscopic bugs. Some of the most robust demand for biocides is in the cooling water market, particularly as industrial water treatment continues to switch from gaseous chlorine to bromine compounds. The trend toward closed-loop and faster cycles for process water treatment will require more biological control. Biocides are expectedmore » to benefit from that trend, but in pulp and paper operations, chlorine dioxide may reap the biggest gains. Also making inroads is an electrolytic system that uses ClO{sub 2} to control microorganisms in cooling towers. Despite growing demand for safe and more-effective biocides in Europe and the US, new product development is stymied by the rigorous and costly process of getting regulatory approval. In the US, EPA registration can cost $5--10 million and take 5 to 10 years.« less

Compatibility Study of Silver Biocide in Drinking Water with Candidate Metals for Crew Exploration Vehicle Potable Water System

NASA Technical Reports Server (NTRS)

Adam, Niklas M.

2009-01-01

The stability of silver biocide, used to keep drinking water on the CEV potable water sterile, is unknown as the system design is still in progress. Silver biocide in water can deplete rapidly when exposed to various metal surfaces. Additionally, silver depletion rates may be affected by the surface-area-to-volume (SA/V) ratios in the water system. Therefore, to facilitate the CEV water system design, it would be advantageous to know the biocide depletion rates in water exposed to the surfaces of these candidate metals at various SA/V ratios. Certain surface treatments can be employed to reduce the depletion rates of silver compared to the base metal. The purpose of this work is to determine the compatibility of specific spaceflight-certified metals that could used in the design of the CEV potable water system with silver biocide as well as understand the effect of surface are to volume ratios of metals used in the construction of the potable water system on the silver concentration.

Displacement imprinted polymer receptor analysis (DIPRA) for chlorophenolic contaminants in drinking water and packaging materials.

PubMed

Nicholls, C; Karim, K; Piletsky, S; Saini, S; Setford, S

2006-01-15

The preparation of a molecularly imprinted polymer (MIP) for pentachlorophenol is described together with two alternative reporter derivatives for use in a displacement imprinted polymer receptor analysis (DIPRA) format procedure. In this procedure, alternative reporter molecules were rebound to the synthetic receptor sites and their displacement by the target analyte was employed as the basis of a simple procedure for the measurement of chlorophenols in water and packaging material samples. Water samples were extracted using the standard procedure (EPA 528) and a detection limit of 0.5 microg l(-1) was achieved using the DIPRA detection method, with good agreement between the displacement technique and GC-ECD analysis. A variety of packaging materials, extracted using a buffered detergent solution were also analysed using the DIPRA procedure and showed good agreement with GC results. In addition, investigation of the cross-reactivity of a range of pesticides and materials commonly encountered in environmental analysis indicated the procedure gave good discrimination between pesticides bearing a chlorophenolic moiety and other materials. The procedure is considered highly suitable for use as a rapid field-test method or for incorporation into a test kit device.

Performance and Mechanism of Piezo-Catalytic Degradation of 4-Chlorophenol: Finding of Effective Piezo-Dechlorination.

PubMed

Lan, Shenyu; Feng, Jinxi; Xiong, Ya; Tian, Shuanghong; Liu, Shengwei; Kong, Lingjun

2017-06-06

Piezo-catalysis was first used to degrade a nondye pollutant, 4-chlorophenol (4-CP). In this process, hydrothermally synthesized tetragonal BaTiO 3 nano/micrometer-sized particles were used as the piezo-catalyst, and the ultrasonic irradiation with low frequency was selected as the vibration energy to cause the deformation of tetragonal BaTiO 3 . It was found that the piezoelectric potential from the deformation could not only successfully degrade 4-chlorophenol but also effectively dechlorinate it at the same time, and five kinds of dechlorinated intermediates, hydroquinone, benzoquinone, phenol, cyclohexanone, and cyclohexanol, were determined. This is the first sample of piezo-dechlorination. Although various active species, including h + , e - , •H, •OH, •O 2 - , 1 O 2 , and H 2 O 2 , were generated in the piezoelectric process, it was confirmed by ESR, scavenger studies, and LC-MS that the degradation and dechlorination were mainly attributed to •OH radicals. These •OH radicals were chiefly derived from the electron reduction of O 2 , partly from the hole oxidation of H 2 O. These results indicated that the piezo-catalysis was an emerging and effective advanced oxidation technology for degradation and dechlorination of organic pollutants.

Degradation of various chlorophenols under alkaline conditions by gram-negative bacteria closely related to Ochrobactrum anthropi.

PubMed

Müller, R H; Jorks, S; Kleinsteuber, S; Babel, W

1998-01-01

From concrete debris of a demolished herbicide production plant several Gram-negative bacterial strains were isolated, which exhibit metabolic capabilities for the degradation of 2,4-dichlorophenol (DCP)l), 4-chloro-2-methylphenol (MCP) and 4-chlorophenol (4-CP), while 2-chlorophenol (2-CP) was degraded at a slower rate. Degradative activity was inducible and was impeded by adding of 100 mg/l of chloramphenicol to growing cultures. The strains displayed alkaliphilic properties with optimum DCP/MCP degradation at pH values around 8.5-9.5; activity was observed up to pH values of 11. Degradation was most likely complete according to chlorine balances; formation of intermediary products was observed with MCP some time. Specific activity of up to 380 mumol/h.g dry mass was found within the concentration range of 10-20 mg/l DCP; higher concentrations retarded the activity with complete inhibition at 200-400 mg/l. Some of the strains carry plasmids whose presence was not unambiguously correlated to the degradative properties. Ribotyping revealed a high degree of relationship between the strains. Preliminary taxonomic investigations showed close relationship to Ochrobactrum anthropi.

The influence of pH on the degradation of phenol and chlorophenols by potassium ferrate.

PubMed

Graham, Nigel; Jiang, Cheng-Chun; Li, Xiang-Zhong; Jiang, Jia-Qian; Ma, Jun

2004-09-01

This paper presents information concerning the influence of solution pH on the aqueous reaction between potassium ferrate and phenol and three chlorinated phenols: 4-chlorophenol (CP), 2,4-dichlorophenol (DCP), 2,4,6-trichlorophenol (TCP). The redox potential and aqueous stability of the ferrate ion, and the reactivity of dissociating compounds, are known to be pH dependent. Laboratory tests have been undertaken over a wide range of pH (5.8-11) and reactant concentrations (ferrate:compound molar ratios of 1:1 to 8:1). The reactivity of trichloroethylene was also investigated as a reference compound owing to its non-dissociating nature. The extent of compound degradation by ferrate was found to be highly pH dependent, and the optimal pH (maximum degradation) decreased in the order: phenol/CP, DCP, TCP; at the optimal pH the degree of degradation of these compounds was similar. The results indicate that for the group of phenol and chlorophenols studied, the presence of an increasing number of chlorine substituent atoms corresponds to an increasing reactivity of the undissociated compound, and a decreasing reactivity of the dissociated compound.

Photocatalytic oxidation of organic compounds via waveguide-supported titanium dioxide films

NASA Astrophysics Data System (ADS)

Miller, Lawrence W.

A photochemical reactor based on titanium dioxide (TiO2)-coated silica optical fibers was constructed to explore the use of waveguide-supported TiO2 films for photocatalytic oxidation of organic compounds. The reactor was used for the photocatalytic oxidation of 4-chlorophenol in water. It was confirmed that TiO2 films could be securely attached to silica optical fibers. The 4-chlorophenol (100 mumol/L in water) was successfully oxidized on the TiO2 surface when UV light (310 nm--380 nm) was propagated through the fibers to the films. Rates of 4-chlorophenol oxidation and UV light flux to the fibers were measured. The quantum efficiency of 4-chlorophenol oxidation [defined as the change in 4-chlorophenol concentration divided by the UV light absorbed by the catalyst] was determined as a function of TiO2 catalyst film thickness and internal incident angle of propagating UV light. A maximum quantum efficiency of 2.8% was measured when TiO2 film thickness was ca. 80 nm and the maximum internal incident angle of propagating light was 84°. Quantum efficiency increased with increasing internal angle of incidence of propagating light and decreased with TiO2 film thickness. UV-Visible internal reflection spectroscopy was used to determine whether UV light propagated through TiO2-coated silica waveguides in an ATR mode. Propagation of UV light in an ATR mode was confirmed by the similarities between internal reflection spectra of phenolphthalein obtained with uncoated and TiO2-coated silica crystals. Planar silica waveguides coated with TiO2 were employed in a photocatalytic reactor for the oxidation of formic acid (833 mumol/L in water). It was shown that the quantum yield of formic acid oxidation [defined as the moles of formic acid oxidized divided by the moles of UV photons absorbed by the catalyst] on the waveguide-supported TiO2 surface is enhanced when UV light propagates through the waveguides in an ATR mode. A maximum quantum yield of 3.9% was found for formic acid oxidation on silica waveguides. The waveguides were coated with 150 nm of TiO2 and activated with UV light (lambdamax = 360 nm) propagating through the waveguides at an internal incident angle of 68°.

The Potential of Antimicrobial Peptides as Biocides

PubMed Central

Laverty, Garry; Gorman, Sean P.; Gilmore, Brendan F.

2011-01-01

Antimicrobial peptides constitute a diverse class of naturally occurring antimicrobial molecules which have activity against a wide range of pathogenic microorganisms. Antimicrobial peptides are exciting leads in the development of novel biocidal agents at a time when classical antibiotics are under intense pressure from emerging resistance, and the global industry in antibiotic research and development stagnates. This review will examine the potential of antimicrobial peptides, both natural and synthetic, as novel biocidal agents in the battle against multi-drug resistant pathogen infections. PMID:22072905

Antifouling processes and toxicity effects of antifouling paints on marine environment. A review.

PubMed

Amara, Intissar; Miled, Wafa; Slama, Rihab Ben; Ladhari, Neji

2018-01-01

The production infrastructure in aquaculture invariably is a complex assortment of submerged components with cages, nets, floats and ropes. Cages are generally made from polyamide or high density polyethylene (PEHD). All of these structures serve as surfaces for biofouling. However, cage nets and supporting infrastructure offer fouling organisms thousands of square meters of multifilament netting. That's why, before immersing them in seawater, they should be coated with an antifouling agent. It helps to prevent net occlusion and to increase its lifespan. Biofouling in marine aquaculture is a specific problem and has three main negative effects. It causes net occlusion and so restricts water and oxygen exchange. Besides, the low dissolved oxygen levels from poor water exchange increases the stress levels of fish, lowers immunity and increases vulnerability to disease. Also, the extra weight imposed by fouling causes cage deformation and structural fatigue. The maintenance and loss of equipment cause the increase of production costs for the industry. Biocides are chemical substances that can prohibit or kill microorganisms responsible for biofouling. The expansion of the aquaculture industry requires the use of more drugs, disinfectants and antifoulant compounds (biocides) to eliminate the microorganisms in the aquaculture facilities. Unfortunately, the use of biocides in the aquatic environment has proved to be harmful as it has toxic effects on the marine environment. The most commonly used biocides in antifouling paints are Tributyltin (TBT), Chlorothalonil, Dichlofluanid, Sea-Nine 211, Diuron, Irgarol 1051 and Zinc Pyrithione. Restrictions were imposed on the use of TBT, that's why organic booster biocides were recently introduced. The replacement products are generally based on copper metal oxides and organic biocides. This paper provides an overview of the effects of antifouling biocides on aquatic organisms. It will focus on the eight booster biocides in common use, despite little data are available for some of them. Toxicity values and effects of these antifoulants will also be mentioned for different species of fish, crustaceans, invertebrates and algae. Copyright © 2017 Elsevier B.V. All rights reserved.

Colorimetric Solid Phase Extraction (CSPE): Using Color to Monitor Spacecraft Water Quality

NASA Technical Reports Server (NTRS)

Gazda, Daniel B.; Nolan, Daniel J.; Rutz, Jeffrey A.; Schultz, John R.; Siperko, Lorraine M.; Porter, Marc D.; Lipert, Robert J.; Flint, Stephanie M.; McCoy, J. Torin

2010-01-01

In August 2009, an experimental water quality monitoring kit based on Colorimetric Solid Phase Extraction (CSPE) technology was delivered to the International Space Station (ISS). The kit, called the Colorimetric Water Quality Monitoring Kit (CWQMK), was launched as a Station Development Test Objective (SDTO) experiment to evaluate the suitability of CSPE technology for routine use monitoring water quality on the ISS. CSPE is a sorption-spectrophotometric technique that combines colorimetric reagents, solid-phase extraction, and diffuse reflectance spectroscopy to quantify trace analytes in water samples. In CSPE, a known volume of sample is metered through a membrane disk that has been impregnated with an analyte-specific colorimetric reagent and any additives required to optimize the formation of the analyte-reagent complex. As the sample flows through the membrane disk, the target analyte is selectively extracted, concentrated, and complexed. Formation of the analyte-reagent complex causes a detectable change in the color of the membrane disk that is proportional to the amount of analyte present in the sample. The analyte is then quantified by measuring the color of the membrane disk surface using a hand-held diffuse reflectance spectrophotometer (DRS). The CWQMK provides the capability to measure the ionic silver (Ag +) and molecular iodine (I2) in water samples on-orbit. These analytes were selected for the evaluation of CSPE technology because they are the biocides used in the potable water storage and distribution systems on the ISS. Biocides are added to the potable water systems on spacecraft to inhibit microbial growth. On the United States (US) segment of the ISS molecular iodine serves as the biocide, while the Russian space agency utilizes silver as a biocide in their systems. In both cases, the biocides must be maintained at a level sufficient to control bacterial growth, but low enough to avoid any negative effects on crew health. For example, the presence of high levels of iodine in water can cause taste and odor issues that result in decreased water consumption by the crew. There are also concerns about potential impacts on thyroid function following exposure to high levels of iodine. With silver, there is a risk of developing argyria, an irreversible blue-gray discoloration of the skin, associated with long term consumption of water containing high concentrations of silver. The need to ensure that safe, effective levels of biocide are maintained in the potable water systems on the ISS provides a perfect platform for evaluating the suitability of CSPE technology for in-flight water quality monitoring. This paper provides an overview of CSPE technology and details on the silver and iodine methods used in the CWQMK. It also reports results obtained during in-flight analyses performed with the CWQMK and briefly discusses other potential applications for CSPE technology in both the spacecraft and terrestrial environments.

Emission of biocides from treated materials: test procedures for water and air.

PubMed

Schoknecht, Ute; Wegner, Robby; Horn, Wolfgang; Jann, Oliver

2003-01-01

Methods for the determination of biocide emissions from treated materials into water and air were developed and tested in order to support a comparative ecological assessment of biocidal products. Leaching tests, experiments with simulated rain, extraction cleaning of carpets and emission chamber tests were performed with a series of treated materials. The experiments focused on the effect of changes in the procedure as well as characteristics of the specimens and demonstrate the suitability of the proposed methods for biocides of different product types. It was demonstrated that emissions of biocides into water can be compared on the basis of leaching tests in which the emission kinetics of the active ingredients are recorded. However, the water volume per surface area and the timetable for water changes have to be defined in such tests. Functions of flux rates related to time can be well described for inorganic compounds, whereas modelling of the data is more complicated for organic substances. Emission chamber tests using 20-litre and 23-litre glass exsiccators, originally developed to study volatile organic compounds, were successfully adapted for the investigation of the emission of biocides from treated materials which are usually semi volatile organic compounds. However test parameters and the method of analysis have to be adapted to the substances to be determined. Generally, it was found that the emission curves for the semi volatile organic compounds investigated differ from those of volatile organic compounds.

Reduction of healthcare-associated infections in a long-term care brain injury ward by replacing regular linens with biocidal copper oxide impregnated linens.

PubMed

Lazary, A; Weinberg, I; Vatine, J-J; Jefidoff, A; Bardenstein, R; Borkow, G; Ohana, N

2014-07-01

Contaminated textiles in hospitals contribute to endogenous, indirect-contact, and aerosol transmission of nosocomial related pathogens. Copper oxide impregnated linens have wide-spectrum antimicrobial, antifungal, and antiviral properties. Our aim was to determine if replacing non-biocidal linens with biocidal copper oxide impregnated linens would reduce the rates of healthcare-associated infections (HAI) in a long-term care ward. We compared the rates of HAI in two analogous patient cohorts in a head injury care ward over two 6-month parallel periods before (period A) and after (period B) replacing all the regular non-biocidal linens and personnel uniforms with copper oxide impregnated biocidal products. During period B, in comparison to period A, there was a 24% reduction in the HAI per 1000 hospitalization-days (p<0.05), a 47% reduction in the number of fever days (>38.5°C) per 1000 hospitalization-days (p<0.01), and a 32.8% reduction in total number of days of antibiotic administration per 1000 hospitalization-days (p<0.0001). Accordingly there was saving of approximately 27% in costs of antibiotics, HAI-related treatments, X-rays, disposables, labor, and laundry, expenses during period B. The use of biocidal copper oxide impregnated textiles in a long-term care ward may significantly reduce HAI, fever, antibiotic consumption, and related treatment costs. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Ozonation of Common Textile Auxiliaries

NASA Astrophysics Data System (ADS)

Iskender, Gulen; Arslan-Alaton, Idil; Koyunluoglu, Sebnem; Yilmaz, Zeynep; Germirli Babuna, Fatos

2016-10-01

The treatability of four different commonly applied textile auxiliary chemicals, namely two tannin formulations (Tannin 1: a condensation product of aryl sulphonate; Tannin 2: natural tannic acid) and two biocidal finishing agents (Biocide 1: 2,4,4’-trichloro-2’- hydroxydiphenyl ether; Biocide 2: a nonionic diphenyl alkane derivative) with ozone was investigated. Increasing the ozone dose yielded higher COD removals for the natural tannin. Optimum ozone doses of 485 and 662 mg/h were obtained at a pH of 3.5 for natural and synthetic tannin carrying textile bath discharges, respectively. When the reaction pH was increased from 3.5 to 7.0, a slight decrease in COD removal was observed for the natural tannin due to ozone selectivity towards its polyaromatic structure. The same increase in ozonation pH enhanced COD removals for the synthetic tannin as a result of enhanced ozone decomposition rendering free radical chain reactions dominant. Optimum ozone doses of 499 and 563 mg/h were established for Biocide 1 and 2, respectively. With the increase of ozonation, pH exhibited a positive influence on COD removals for both textile tannins. A substantial improvement in terms of TOC removals was observed as the reaction pH was increased from 3.5 to 7.0 for the synthetic tannin, and from 7 to 12 for both textile biocides. Higher AOX removals were evident at pH 7 than at pH 12 for Biocide 1 as a result of the higher selectivity of the dehalogenation reaction at neutral pH.

Controlling the invasive diatom Didymosphenia geminata: an ecotoxicity assessment of four potential biocides.

PubMed

Jellyman, P G; Clearwater, S J; Clayton, J S; Kilroy, C; Blair, N; Hickey, C W; Biggs, B J F

2011-07-01

In 2004, an invasive mat-forming freshwater diatom, Didymosphenia geminata (didymo), was found in New Zealand causing concern with regard to potential consequences for local freshwater ecosystems. A four-stage research program was initiated to identify methods to control D. geminata. This article reports the results of Stage 2, in which four potential control compounds [Gemex™ (a chelated copper formulation), EDTA, Hydrothol®191, and Organic Interceptor™ (a pine oil formulation)] selected in Stage 1 were evaluated for their biocidal efficacy on D. geminata and effects on non-target organisms using both artificial stream and laboratory trials. Artificial stream trials evaluated the mortality rates of D. geminata and fishes to three concentrations of the four biocides, whereas laboratory toxicity trials tested the response of green alga and cladocera to a range of biocide concentrations and exposure times. In artificial stream trials, Gemex and Organic Interceptor were the most effective biocides against D. geminata for a number of measured indices; however, exposure of fishes to Organic Interceptor resulted in high mortality rates. Laboratory toxicity testing indicated that Gemex might negatively affect sensitive stream invertebrates, based on the cladoceran sensitivity at the proposed river control dose. A decision support matrix evaluated the four biocides based on nine criteria stipulated by river stakeholders (effectiveness, non-target species impacts, stalk removal, degradation profile, risks to health and safety, ease of application, neutralization potential, cost, and local regulatory requirements) and Gemex was identified as the product warranting further refinement prior to an in-river trial.

Magnetically Separable MoS2/Fe3O4/nZVI Nanocomposites for the Treatment of Wastewater Containing Cr(VI) and 4-Chlorophenol

PubMed Central

Wang, Jingkang; Wang, Ting

2017-01-01

With a large specific surface area, high reactivity, and excellent adsorption properties, nano zerovalent iron (nZVI) can degrade a wide variety of contaminants in wastewater. However, aggregation, oxidation, and separation issues greatly impede its wide application. In this study, MoS2/Fe3O4/nZVI nanocomposites were successfully synthesized by a facile step-by-step approach to overcome these problems. MoS2 nanosheets (MNs) acted as an efficient support for nZVI and enriched the organic pollutants nearby, leading to an enhanced removal efficiency. Fe3O4 nanoparticles (NPs) could not only suppress the agglomeration and restacking of MNs, but also facilitate easy separation and recovery of the nanocomposites. The synergistic effect between MNs and Fe3O4 NPs effectively enhanced the reactivity and efficiency of nZVI. In the system, Cr(VI) was reduced to Cr(III) by nZVI in the nanocomposites, and Fe2+ produced in the process was combined with H2O2 to further remove 4-Chlorophenol (4-CP) through a Fenton reaction. Furthermore, the nanocomposites could be easily separated from wastewater by a magnet and be reused for at least five consecutive runs, revealing good reusability. The results demonstrate that the novel nanocomposites are highly efficient and promising for the simultaneous removal of Cr(VI) and 4-CP in wastewater. PMID:28973986

Controlled release for crop and wood protection: Recent progress toward sustainable and safe nanostructured biocidal systems.

PubMed

Mattos, Bruno D; Tardy, Blaise L; Magalhães, Washington L E; Rojas, Orlando J

2017-09-28

We review biocide delivery systems (BDS), which are designed to deter or control harmful organisms that damage agricultural crops, forests and forest products. This is a timely topic, given the growing socio-economical concerns that have motivated major developments in sustainable BDS. Associated designs aim at improving or replacing traditional systems, which often consist of biocides with extreme behavior as far as their solubility in water. This includes those that compromise or pollute soil and water (highly soluble or volatile biocides) or those that present low bioavailability (poorly soluble biocides). Major breakthroughs are sought to mitigate or eliminate consequential environmental and health impacts in agriculture and silviculture. Here, we consider the most important BDS vehicles or carriers, their synthesis, the environmental impact of their constituents and interactions with the active components together with the factors that affect their rates of release such as environmental factors and interaction of BDS with the crops or forest products. We put in perspective the state-of-the-art nanostructured carriers for controlled release, which need to address many of the challenges that exist in the application of BDS. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of enterocin AS-48 in combination with biocides on planktonic and sessile Listeria monocytogenes.

PubMed

Gómez, Natacha Caballero; Abriouel, Hikmate; Grande, M A José; Pulido, Rubén Pérez; Gálvez, Antonio

2012-05-01

Enterocin AS-48 was tested on a cocktail of Listeria monocytogenes strains in planktonic and sessile states, singly or in combination with biocides benzalkonium chloride, cetrimide, hexadecylpyridinium chloride, didecyldimethylammonium bromide, triclosan, poly-(hexamethylen guanidinium) hydrochloride, chlorhexidine, hexachlorophene, and the commercial sanitizers P3 oxonia and P3 topax 66. Combinations of sub-inhibitory bacteriocin concentrations and biocide concentrations 4 to 10-fold lower than their minimum inhibitory concentrations (MIC) completely inhibited growth of the planktonic listeriae. Inactivation of Listeria in biofilms formed on polystyrene microtiter plates required concentrations of enterocin AS-48 greater than 50 μg/ml, and biocide concentrations ten to 100-fold higher. In combination with enterocin AS-48 (25 or 50 μg/ml), microbial inactivation increased remarkably for all biocides except P3 oxonia and P3 topax 66 solutions. Polystyrene microtiter plates conditioned with enterocin solutions (0.5-25 μg/ml) decreased the adherence and biofilm formation of the L. monocytogenes cell cocktail, avoiding biofilm formation for at least 24 h at a bacteriocin concentration of 25 μg/ml. Copyright © 2011 Elsevier Ltd. All rights reserved.

Diatom communities on commercial biocidal fouling control coatings after one year of immersion in the marine environment.

PubMed

Muthukrishnan, Thirumahal; Dobretsov, Sergey; De Stefano, Mario; Abed, Raeid M M; Kidd, Barry; Finnie, Alistair A

2017-08-01

Little is known about the effect of commercial biocidal fouling control coatings on fouling diatom communities and their growth forms after long periods of exposure in the marine tropical environment. The current study investigated the abundance and composition of fouling diatom communities developed on 11 commercially available biocidal antifouling coatings, covering the three main technology types in recent historic use (Self-Polishing Copolymers, Self-Polishing Hybrid and Controlled Depletion Polymers) after one year of static immersion at two locations in Muscat, Oman (Marina Shangri La and Marina Bandar Rowdha). Light microscopy demonstrated that the total abundance of diatoms and the relative abundance of growth forms were significantly affected by the choice of biocidal antifouling coating and experimental location. Using scanning electron microscopy, a total of 21 diatom genera were identified which were grouped into adnate, motile, plocon and erect growth forms. The adnate growth forms, mainly the genera Amphora, Cocconeis and Mastogloia, dominated the other growth forms in terms of their relative abundance. Current results revealed the importance of exposure location and choice of biocidal antifouling coating on the relative abundance of diatom growth forms. Copyright © 2017 Elsevier Ltd. All rights reserved.

Adverse Effect of Antifouling Compounds on the Reproductive Mechanisms of the Ascidian Ciona intestinalis

PubMed Central

Gallo, Alessandra; Tosti, Elisabetta

2013-01-01

Fertilization and embryo development that occur in sea water are sensitive to xenobiotics from anthropogenic sources. In this work, we evaluated the influence of two antifouling biocides, tributyltin (TBT) and diuron, on the reproductive mechanisms of the marine invertebrate Ciona intestinalis. By using electrophysiological techniques, we examined the impact of these compounds on the electrical properties of the mature oocytes and of events occurring at fertilization. With different toxicity assays, we studied the effect of the two biocides on the gametes by evaluating fertilization rate and embryo development. Results show that sodium (Na+) currents were significantly reduced by either of the two biocides, whereas conductance was significantly increased. The fertilization current frequency and amplitude, fertilization rate and larval development were affected only by TBT. This study suggests that: (i) the two biocides affect either the electrical properties of the oocyte plasma membrane and the reproductive success representing a risk factor for the survival of the species exposed to environmental pollution; (ii) the ascidian Ciona intestinalis may represent a good model organism to test toxicity of marine pollutants. Possible mechanisms of action of the two biocides are discussed. PMID:24065165

Comparative evaluation of the activity of commercial biocides in relation to micromycetes

NASA Astrophysics Data System (ADS)

Strokova, Valeria; Nelyubova, Victoria; Vasilenko, Marina; Goncharova, Elena; Rykunova, Marina; Kalatozi, Elina

2017-11-01

The paper presents the results of comparative studies of commercial biocides of Russian production, used in the technology of biostable materials for construction purposes, to micromycetes of various species and type diversity. The influence of the type of biocide additive on their fungicidal activity was established. The fungicidal effect of bioactive agents was evaluated using a disc-diffusion method. The analysis of the results is carried out both using the traditional approach and a modified method using a scoring of the degree of impact.

Control of Microbial Sulfide Production with Biocides and Nitrate in Oil Reservoir Simulating Bioreactors

PubMed Central

Xue, Yuan; Voordouw, Gerrit

2015-01-01

Oil reservoir souring by the microbial reduction of sulfate to sulfide is unwanted, because it enhances corrosion of metal infrastructure used for oil production and processing. Reservoir souring can be prevented or remediated by the injection of nitrate or biocides, although injection of biocides into reservoirs is not commonly done. Whether combined application of these agents may give synergistic reservoir souring control is unknown. In order to address this we have used up-flow sand-packed bioreactors injected with 2 mM sulfate and volatile fatty acids (VFA, 3 mM each of acetate, propionate and butyrate) at a flow rate of 3 or 6 pore volumes (PV) per day. Pulsed injection of the biocides glutaraldehyde (Glut), benzalkonium chloride (BAC) and cocodiamine was used to control souring. Souring control was determined as the recovery time (RT) needed to re-establish an aqueous sulfide concentration of 0.8–1 mM (of the 1.7–2 mM before the pulse). Pulses were either for a long time (120 h) at low concentration (long-low) or for a short time (1 h) at high concentration (short-high). The short-high strategy gave better souring control with Glut, whereas the long-low strategy was better with cocodiamine. Continuous injection of 2 mM nitrate alone was not effective, because 3 mM VFA can fully reduce both 2 mM nitrate to nitrite and N2 and, subsequently, 2 mM sulfate to sulfide. No synergy was observed for short-high pulsed biocides and continuously injected nitrate. However, use of continuous nitrate and long-low pulsed biocide gave synergistic souring control with BAC and Glut, as indicated by increased RTs in the presence, as compared to the absence of nitrate. Increased production of nitrite, which increases the effectiveness of souring control by biocides, is the most likely cause for this synergy. PMID:26696994

BioCIDER: a Contextualisation InDEx for biological Resources discovery

PubMed Central

Horro, Carlos; Cook, Martin; Attwood, Teresa K.; Brazas, Michelle D.; Hancock, John M.; Palagi, Patricia; Corpas, Manuel; Jimenez, Rafael

2017-01-01

Abstract Summary The vast, uncoordinated proliferation of bioinformatics resources (databases, software tools, training materials etc.) makes it difficult for users to find them. To facilitate their discovery, various services are being developed to collect such resources into registries. We have developed BioCIDER, which, rather like online shopping ‘recommendations’, provides a contextualization index to help identify biological resources relevant to the content of the sites in which it is embedded. Availability and Implementation BioCIDER (www.biocider.org) is an open-source platform. Documentation is available online (https://goo.gl/Klc51G), and source code is freely available via GitHub (https://github.com/BioCIDER). The BioJS widget that enables websites to embed contextualization is available from the BioJS registry (http://biojs.io/). All code is released under an MIT licence. Contact carlos.horro@earlham.ac.uk or rafael.jimenez@elixir-europe.org or manuel@repositive.io PMID:28407033

Two-Functional Direct Current Sputtered Silver-Containing Titanium Dioxide Thin Films

NASA Astrophysics Data System (ADS)

Musil, J.; Louda, M.; Cerstvy, R.; Baroch, P.; Ditta, I. B.; Steele, A.; Foster, H. A.

2009-04-01

The article reports on structure, mechanical, optical, photocatalytic and biocidal properties of Ti-Ag-O films. The Ti-Ag-O films were reactively sputter-deposited from a composed Ti/Ag target at different partial pressures of oxygen p_{O2} on unheated glass substrate held on floating potential U fl. It was found that addition of 2 at.% of Ag into TiO2 film has no negative influence on UV-induced hydrophilicity of TiO2 film. Thick ( 1,500 nm) TiO2/Ag films containing (200) anatase phase exhibit the best hydrophilicity with water droplet contact angle (WDCA) lower than 10° after UV irradiation for 20 min. Thick ( 1,500 nm) TiO2/Ag films exhibited a better UV-induced hydrophilicity compared to that of thinner ( 700 nm) TiO2/Ag films. Further it was found that hydrophilic TiO2/Ag films exhibit a strong biocidal effect under both the visible light and the UV irradiation with 100% killing efficiency of Escherichia coli ATCC 10536 after UV irradiation for 20 min. Reported results show that single layer of TiO2 with Ag distributed in its whole volume exhibits, after UV irradiation, simultaneously two functions: (1) excellent hydrophilicity with WDCA < 10° and (2) strong power to kill E. coli even under visible light due to direct toxicity of Ag.

Bacteria survival probability in bactericidal filter paper.

PubMed

Mansur-Azzam, Nura; Hosseinidoust, Zeinab; Woo, Su Gyeong; Vyhnalkova, Renata; Eisenberg, Adi; van de Ven, Theo G M

2014-05-01

Bactericidal filter papers offer the simplicity of gravity filtration to simultaneously eradicate microbial contaminants and particulates. We previously detailed the development of biocidal block copolymer micelles that could be immobilized on a filter paper to actively eradicate bacteria. Despite the many advantages offered by this system, its widespread use is hindered by its unknown mechanism of action which can result in non-reproducible outcomes. In this work, we sought to investigate the mechanism by which a certain percentage of Escherichia coli cells survived when passing through the bactericidal filter paper. Through the process of elimination, the possibility that the bacterial survival probability was controlled by the initial bacterial load or the existence of resistant sub-populations of E. coli was dismissed. It was observed that increasing the thickness or the number of layers of the filter significantly decreased bacterial survival probability for the biocidal filter paper but did not affect the efficiency of the blank filter paper (no biocide). The survival probability of bacteria passing through the antibacterial filter paper appeared to depend strongly on the number of collision between each bacterium and the biocide-loaded micelles. It was thus hypothesized that during each collision a certain number of biocide molecules were directly transferred from the hydrophobic core of the micelle to the bacterial lipid bilayer membrane. Therefore, each bacterium must encounter a certain number of collisions to take up enough biocide to kill the cell and cells that do not undergo the threshold number of collisions are expected to survive. Copyright © 2014 Elsevier B.V. All rights reserved.

Increased Usage of Antiseptics Is Associated with Reduced Susceptibility in Clinical Isolates of Staphylococcus aureus

PubMed Central

Hardy, Katherine; Sunnucks, Katie; Gil, Hannah; Shabir, Sahida; Trampari, Eleftheria; Hawkey, Peter

2018-01-01

ABSTRACT Hospital-acquired infection is a major cause of morbidity and mortality, and regimes to prevent infection are crucial in infection control. These include the decolonization of vulnerable patients with methicillin-resistant Staphylococcus aureus (MRSA) carriage using antiseptics, including chlorhexidine and octenidine. Concern has been raised, however, regarding the possible development of biocide resistance. In this study, we assembled a panel of S. aureus isolates, including isolates collected before the development of chlorhexidine and octenidine and isolates, from a major hospital trust in the United Kingdom during a period when the decolonization regimes were altered. We observed significant increases in the MIC and minimum bactericidal concentration (MBC) of chlorhexidine in isolates from periods of high usage of chlorhexidine. Isolates with increased MICs and MBCs of octenidine rapidly emerged after octenidine was introduced in the trust. There was no apparent cross-resistance between the two biocidal agents. A combination of variable-number tandem repeat (VNTR) analysis, PCR for qac genes, and whole-genome sequencing was used to type isolates and examine possible mechanisms of resistance. There was no expansion of a single strain associated with decreased biocide tolerance, and biocide susceptibility did not correlate with carriage of qac efflux pump genes. Mutations within the NorA or NorB efflux pumps, previously associated with chlorhexidine export, were identified, however, suggesting that this may be an important mechanism of biocide tolerance. We present evidence that isolates are evolving in the face of biocide challenge in patients and that changes in decolonization regimes are reflected in changes in susceptibility of isolates. PMID:29844113

Choice of optimal biocide combination to control flies (Diptera: Muscidae).

PubMed

Kavran, Mihaela; Zgomba, Marija F; Ignjatovic-Ćupina, Aleksandra M; Lazić, Sanja D; Petrić, Dušan V

2015-01-01

Flies - by feeding on decaying matter, human waste and food - have been implicated in the spread of numerous animal and human diseases. Excessive fly populations are generally associated with livestock units and domestic waste due to decaying organic matter. A large number of flies cause extreme disturbance in the behavior of the host, resulting in skin irritation, lesions, wounds, and secondary infections are likely to appear. The aim of this study was to evaluate the effects of combined applications of larvicide (cyromazine) and adulticides (acetamiprid in formulation with pheromone and thiamethoxam) on the suppression of fly populations. The study was conducted on a pig farm. The piglet farms are one of the most favorable places for fly breeding. Three units were used for biocide applications and a fourth unit as the control where biocides were not applied. The monitoring of pre- and post-treatment of adult fly populations was carried out by glued cardboards. The cards were hung on metal rods above piglet's cage. This monitoring method served as a parameter for the estimation of biological effectiveness. The highest degree of fly control (88.4% mortality 8 days after treatment) was achieved when a combination of cyromazine and thiamethoxam was used. A biocide based on sex pheromone (Z)-9-tricosene + acetamiprid was the most effective on flies 3 days after biocide application, with a mortality rate of 69.1 %. Thiamethoxam achieved the highest reduction of flies 6 days after treatment, with 78.19% obtained mortality. Biological efficacy of the applied biocides in combination ciromazine + thiamethoxam and thiamethoxam alone was justified.

Modification of the surfaces of medical devices to prevent microbial adhesion and biofilm formation.

PubMed

Desrousseaux, C; Sautou, V; Descamps, S; Traoré, O

2013-10-01

The development of devices with surfaces that have an effect against microbial adhesion or viability is a promising approach to the prevention of device-related infections. To review the strategies used to design devices with surfaces able to limit microbial adhesion and/or growth. A PubMed search of the published literature. One strategy is to design medical devices with a biocidal agent. Biocides can be incorporated into the materials or coated or covalently bonded, resulting either in release of the biocide or in contact killing without release of the biocide. The use of biocides in medical devices is debated because of the risk of bacterial resistance and potential toxicity. Another strategy is to modify the chemical or physical surface properties of the materials to prevent microbial adhesion, a complex phenomenon that also depends directly on microbial biological structure and the environment. Anti-adhesive chemical surface modifications mostly target the hydrophobicity features of the materials. Topographical modifications are focused on roughness and nanostructures, whose size and spatial organization are controlled. The most effective physical parameters to reduce bacterial adhesion remain to be determined and could depend on shape and other bacterial characteristics. A prevention strategy based on reducing microbial attachment rather than on releasing a biocide is promising. Evidence of the clinical efficacy of these surface-modified devices is lacking. Additional studies are needed to determine which physical features have the greatest potential for reducing adhesion and to assess the usefulness of antimicrobial coatings other than antibiotics. Copyright © 2013 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Comparison of experimental methods for determination of toxicity and biodegradability of xenobiotic compounds.

PubMed

Polo, A M; Tobajas, M; Sanchis, S; Mohedano, A F; Rodríguez, J J

2011-07-01

Different methods for determining the toxicity and biodegradability of hazardous compounds evaluating their susceptibility to biological treatment were studied. Several compounds including chlorophenols and herbicides have been evaluated. Toxicity was analyzed in terms of EC50 and by a simple respirometric procedure based on the OECD Method 209 and by the Microtox® bioassay. The values of EC50 obtained from respirometry were in all the cases higher than those from the Microtox® test. The respirometric inhibition values of chlorophenols were related well with the number of chlorine atoms and their position in the aromatic ring. In general, herbicides showed lower inhibition, being alachlor the less toxic from this criterion. For determination of biodegradability an easier and faster alternative to the OECD Method 301, with a higher biomass to substrate ratio is proposed. When this test was negative, the Zahn-Wellens one was performed in order to evaluate the inherent biodegradability. In the fast test of biodegradability, 4-chlorocatechol and 4-chlorophenol showed a complete biodegradation by an unacclimated sludge upon 48 h. These results together with their low respirometric inhibition, allow concluding that these compounds could be conveniently removed in a WWTP. Alachlor, 2,4-dichlorophenol, 2,4,6-trichlorophenol and MCPA showed a partial biodegradation upon 28 days by the Zahn-Wellens inherent biodegradability test.

Suitability of dispersive liquid-liquid microextraction for the in situ silylation of chlorophenols in water samples before gas chromatography with mass spectrometry.

PubMed

Saraji, Mohammad; Ghambari, Hoda

2015-10-01

Trace analysis of chlorophenols in water was performed by simultaneous silylation and dispersive liquid-liquid microextraction followed by gas chromatography with mass spectrometry. Dispersive liquid-liquid microextraction was carried out using an organic solvent lighter than water (n-hexane). The effect of different silylating reagents on the method efficiency was investigated. The influence of derivatization reagent volume, presence of catalyst and derivatization/extraction time on the yield of the derivatization reaction was studied. Different parameters affecting extraction efficiency such as kind and volume of extraction and disperser solvents, pH of the sample and addition of salt were also investigated and optimized. Under the optimum conditions, the calibration graphs were linear in the range of 0.05-100 ng/mL and the limit of detection was 0.01 ng/mL. The enrichment factors were 242, 351, and 363 for 4-chlorophenol, 2,4-dichlorophenol, and 2,4,6-trichlorophenol, respectively. The values of intra- and inter-day relative standard deviations were in the range of 3.0-6.4 and 6.1-9.9%, respectively. The applicability of the method was investigated by analyzing water and wastewater samples. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of polysiloxane with quaternized N-halamine moieties for antibacterial coating of polypropylene via supercritical impregnation technique

NASA Astrophysics Data System (ADS)

Chen, Yong; Yu, Panwei; Feng, Chunyan; Wang, Yuyu; Han, Qiuxia; Zhang, Qiang

2017-10-01

Development of polymers with enhanced biocidal ability to coated surfaces by a simple and versatile approach is very desirable in biomaterial area. A polysiloxane containing both quaternary ammonium and N-halamine was synthesized by silane alcoholysis between poly(methylhydrosiloxane) (PMHS) and 3-bromo-1-propanol, subsequent quaternization with 3-(3-(dimethylamino)propyl)-5,5-dimethylhydantoin (DMAPDMH), and chlorination with tert-butyl hypochlorite. The quaternized N-halamine polysiloxane was impregnated into polypropylene (PP) in supercritical carbon dioxide (scCO2) and formed an antibacterial coating layer of 61 nm. The synthetic procedures and coating results were characterized using FTIR, NMR, XPS, and SEM. The polysiloxane layer showed enhanced synergetic antibacterial ability, providing a total kill of a 7-log S. aureus and E. coli within 10 min of contact. The rechargability and stability of the coating layer toward washing cycles, storage, and UV irradiation were good. This coating procedure uses environmentally benign CO2 as solvent and affords a general method to functionalize inert polymers with biocidal capability.

Tire tread wear particles in ambient air--a previously unknown source of human exposure to the biocide 2-mercaptobenzothiazole.

PubMed

Avagyan, Rozanna; Sadiktsis, Ioannis; Bergvall, Christoffer; Westerholm, Roger

2014-10-01

Urban particulate matter (PM), asphalt, and tire samples were investigated for their content of benzothiazole and benzothiazole derivates. The purpose of this study was to examine whether wear particles, i.e., tire tread wear or road surface wear, could contribute to atmospheric concentrations of benzothiazole derivatives. Airborne particulate matter (PM10) sampled at a busy street in Stockholm, Sweden, contained on average 17 pg/m(3) benzothiazole and 64 pg/m(3) 2-mercaptobenzothiazole, and the total suspended particulate-associated benzothiazole and 2-mercaptobenzothiazole concentrations were 199 and 591 pg/m(3), respectively. This indicates that tire tread wear may be a major source of these benzothiazoles to urban air PM in Stockholm. Furthermore, 2-mercaptobenzothiazole was determined in urban air particulates for the first time in this study, and its presence in inhalable PM10 implies that the human exposure to this biocide is underestimated. This calls for a revision of the risk assessments of 2-mercaptobenzothiazole exposure to humans which currently is limited to occupational exposure.

Novel silver-based nanoclay as an antimicrobial in polylactic acid food packaging coatings.

PubMed

Busolo, Maria A; Fernandez, Patricia; Ocio, Maria J; Lagaron, Jose M

2010-11-01

This paper presents a comprehensive performance study of polylactic acid (PLA) biocomposites, obtained by solvent casting, containing a novel silver-based antimicrobial layered silicate additive for use in active food packaging applications. The silver-based nanoclay showed strong antimicrobial activity against Gram-negative Salmonella spp. Despite the fact that no exfoliation of the silver-based nanoclay in PLA was observed, as suggested by transmission electron microscopy (TEM) and wide angle X-ray scattering (WAXS) experiments, the additive dispersed nicely throughout the PLA matrix to a nanoscale, yielding nanobiocomposites. The films were highly transparent with enhanced water barrier and strong biocidal properties. Silver migration from the films to a slightly acidified water medium, considered an aggressive food simulant, was measured by stripping voltammetry. Silver migration accelerated after 6 days of exposure. Nevertheless, the study suggests that migration levels of silver, within the specific migration levels referenced by the European Food Safety Agency (EFSA), exhibit antimicrobial activity, supporting the potential application of this biocidal additive in active food-packaging applications to improve food quality and safety.

N-halamine biocidal coatings via a layer-by-layer assembly technique.

PubMed

Cerkez, Idris; Kocer, Hasan B; Worley, S D; Broughton, R M; Huang, T S

2011-04-05

Two N-halamine copolymer precursors, poly(2,2,6,6-tetramethyl-4-piperidyl methacrylate-co-acrylic acid potassium salt) and poly(2,2,6,6-tetramethyl-4-piperidyl methacrylate-co-trimethyl-2-methacryloxyethylammonium chloride) have been synthesized and successfully coated onto cotton fabric via a layer-by-layer (LbL) assembly technique. A multilayer thin film was deposited onto the fiber surfaces by alternative exposure to polyelectrolyte solutions. The coating was rendered biocidal by a dilute household bleach treatment. The biocidal efficacies of tested swatches composed of treated fibers were evaluated against Staphylococcus aureus and Escherichia coli. It was determined that chlorinated samples inactivated both S. aureus and E. coli O157:H7 within 15 min of contact time, whereas the unchlorinated control samples did not exhibit significant biocidal activities. Stabilities of the coatings toward washing and ultraviolet light exposure have also been studied. It was found that the stability toward washing was superior, whereas the UVA light stability was moderate compared to previously studied N-halamine moieties. The layer-by-layer assembly technique can be used to attach N-halamine precursor polymers onto cellulose surfaces without using covalently bonding tethering groups which limit the structure designs. In addition, ionic precursors are very soluble in water, thus promising for biocidal coatings without the use of organic solvents.

Studies on the impact, detection, and control of microbiology influenced corrosion related to pitting failures in the Russian oil and gas industry. Final CRADA report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehst, D.

2006-09-30

The objectives of the Project are: (1) to design effective anti-corrosion preparations (biocides, inhibitors, penetrants and their combinations) for gas- and oil-exploration industries; (2) to study a possibility of development of environmentally beneficial ('green') biocides and inhibitors of the new generation; (3) to develop chemical and microbiological methods of monitoring of sites at risk of corrosion; and (4) to evaluate potentialities in terms of technology, raw materials and material and technical basis to set up a production of effective anti-corrosion preparations of new generation in Russia. During the four years of the project 228 compounds and formulations were synthesized andmore » studied in respect to their corrosion inhibiting activity. A series of compounds which were according to the Bubble tests more efficient (by a factor of 10-100) than the reference inhibitor SXT-1102, some possessing the similar activity or slightly better activity than new inhibitor ??-1154? (company ONDEO/Nalco). Two synthetic routes for the synthesis of mercaptopyrimidines as perspective corrosion inhibitors were developed. Mercaptopyrimidine derivatives can be obtained in one or two steps from cheap and easily available precursors. The cost for their synthesis is not high and can be further reduced after the optimization of the production processes. A new approach for lignin utilization was proposed. Water-soluble derivative of lignin can by transformed to corrosion protective layer by its electropolymerization on a steel surface. Varying lignosulfonates from different sources, as well as conditions of electrooxidation we proved, that drop in current at high anodic potentials is due to electropolymerization of lignin derivative at steel electrode surface. The electropolymerization potential can be sufficiently decreased by an increase in ionic strength of the growing solution. The lignosulfonate electropolymerization led to the considerable corrosion protection effect of carbon steel. More than three times decrease of corrosion rate on steel surface was observed after lignosulfonate electropolymerization, exceeding protective effect of standard commercially available corrosion inhibitor. Solikamsky lignin could be a promising candidate as a base for the development of the future green corrosion inhibitor. A protective effect of isothiazolones in compositions with other biocides and inhibitors was investigated. Additionally to high biocidal properties, combination of kathon 893 and copper sulfate may also produce a strong anticorrosion effect depending on concentrations of the biocides. Based on its joint biocidal and anticorrosion properties, this combination can be recommended for protection of pipelines against carbon dioxide-induced corrosion. By means of linear polarization resistance test, corrosion properties of biocides of different classes were studied. Isothiazolones can be recommended for treating oil-processing waters in Tatarstan to curb carbon dioxide - induced corrosion. A laboratory research on evaluation of the efficiency of biocides, inhibitors and penetrants by biological and physical-and-chemical methods has been carried out. It was shown that action of corrosion inhibitors and biocides strongly depends on character of their interaction with mineral substances available in waters on oil-exploration sites. It was found that one of approaches to designing environmentally safe ('green') antimicrobial formulations may be the use of synergetic combinations, which allow one to significantly decrease concentrations of biocides. It was shown that the efficacy of biocides and inhibitors depends on physicochemical characteristics of the environment. Anticorrosion and antimicrobial effects of biocides and inhibitors depended in much on the type of medium and aeration regimen. Effects of different biocides, corrosion inhibitors. penetrants and their combinations on the biofilm were investigated. It has been shown that minimal inhibiting concentrations of the reagents for the biofilm are much higher than those for aquatic microorganisms. Results obtained from the research in stationary conditions have been confirmed with data from experiments carried out in hydrodynamic conditions. New approaches to the investigation of biocorrosive processes on the basis of bioluminescent method of intracellular ATP determination have been developed. Approaches and methods developed on the basis of bioluminescent method could significantly simplify the analysis of biocorrosion processes and allow to conduct the analysis directly under the field conditions in situ. An express method to assess biogenic sulfate reduction in soil and water samples has been elaborated. The method intends for field application and allows one to no-problem assess action of such harmful and corrosion provoking microorganisms, as sulfate-reducing bacteria.« less

Purification and characterization of a surfactin-like molecule produced by Bacillus sp. H2O-1 and its antagonistic effect against sulfate reducing bacteria.

PubMed

Korenblum, Elisa; de Araujo, Livia Vieira; Guimarães, Carolina Reis; de Souza, Lauro M; Sassaki, Guilherme; Abreu, Fernanda; Nitschke, Márcia; Lins, Ulysses; Freire, Denise Maria Guimarães; Barreto-Bergter, Eliana; Seldin, Lucy

2012-11-07

Bacillus sp. H2O-1, isolated from the connate water of a Brazilian reservoir, produces an antimicrobial substance (denoted as AMS H2O-1) that is active against sulfate reducing bacteria, which are the major bacterial group responsible for biogenic souring and biocorrosion in petroleum reservoirs. Thus, the use of AMS H2O-1 for sulfate reducing bacteria control in the petroleum industry is a promising alternative to chemical biocides. However, prior to the large-scale production of AMS H2O-1 for industrial applications, its chemical structure must be elucidated. This study also analyzed the changes in the wetting properties of different surfaces conditioned with AMS H2O-1 and demonstrated the effect of AMS H2O-1 on sulfate reducing bacteria cells. A lipopeptide mixture from AMS H2O-1 was partially purified on a silica gel column and identified via mass spectrometry (ESI-MS). It comprises four major components that range in size from 1007 to 1049 Da. The lipid moiety contains linear and branched β-hydroxy fatty acids that range in length from C13 to C16. The peptide moiety contains seven amino acids identified as Glu-Leu-Leu-Val-Asp-Leu-Leu.Transmission electron microscopy revealed cell membrane alteration of sulfate reducing bacteria after AMS H2O-1 treatment at the minimum inhibitory concentration (5 μg/ml). Cytoplasmic electron dense inclusions were observed in treated cells but not in untreated cells. AMS H2O-1 enhanced the osmosis of sulfate reducing bacteria cells and caused the leakage of the intracellular contents. In addition, contact angle measurements indicated that different surfaces conditioned by AMS H2O-1 were less hydrophobic and more electron-donor than untreated surfaces. AMS H2O-1 is a mixture of four surfactin-like homologues, and its biocidal activity and surfactant properties suggest that this compound may be a good candidate for sulfate reducing bacteria control. Thus, it is a potential alternative to the chemical biocides or surface coating agents currently used to prevent SRB growth in petroleum industries.

Use of Homogeneously-Sized Carbon Steel Ball Bearings to Study Microbially-Influenced Corrosion in Oil Field Samples

PubMed Central

Voordouw, Gerrit; Menon, Priyesh; Pinnock, Tijan; Sharma, Mohita; Shen, Yin; Venturelli, Amanda; Voordouw, Johanna; Sexton, Aoife

2016-01-01

Microbially-influenced corrosion (MIC) contributes to the general corrosion rate (CR), which is typically measured with carbon steel coupons. Here we explore the use of carbon steel ball bearings, referred to as beads (55.0 ± 0.3 mg; Ø = 0.238 cm), for determining CRs. CRs for samples from an oil field in Oceania incubated with beads were determined by the weight loss method, using acid treatment to remove corrosion products. The release of ferrous and ferric iron was also measured and CRs based on weight loss and iron determination were in good agreement. Average CRs were 0.022 mm/yr for eight produced waters with high numbers (105/ml) of acid-producing bacteria (APB), but no sulfate-reducing bacteria (SRB). Average CRs were 0.009 mm/yr for five central processing facility (CPF) waters, which had no APB or SRB due to weekly biocide treatment and 0.036 mm/yr for 2 CPF tank bottom sludges, which had high numbers of APB (106/ml) and SRB (108/ml). Hence, corrosion monitoring with carbon steel beads indicated that biocide treatment of CPF waters decreased the CR, except where biocide did not penetrate. The CR for incubations with 20 ml of a produced water decreased from 0.061 to 0.007 mm/yr when increasing the number of beads from 1 to 40. CRs determined with beads were higher than those with coupons, possibly also due to a higher weight of iron per unit volume used in incubations with coupons. Use of 1 ml syringe columns, containing carbon steel beads, and injected with 10 ml/day of SRB-containing medium for 256 days gave a CR of 0.11 mm/yr under flow conditions. The standard deviation of the distribution of residual bead weights, a measure for the unevenness of the corrosion, increased with increasing CR. The most heavily corroded beads showed significant pitting. Hence the use of uniformly sized carbon steel beads offers new opportunities for screening and monitoring of corrosion including determination of the distribution of corrosion rates, which allows estimation of the probability of high rate events that may lead to failure. PMID:27047467

THE BIOCIDE TRIBUTYLTIN ALTERS TESTOSTERONE ESTERIFICATION IN MUD SNAILS (ILYANASSA OBSOLETA)

EPA Science Inventory

The Biocide Tributyltin Alters Testosterone Esterification in Mud Snails (Ilyanassa obsoleta)

Meredith P. Gooding and Gerald A. LeBlanc
Department of Environmental and Molecular Toxicology, North Carolina State University, Raleigh, NC 27695-7633

Tributyltin (TBT...

Potential development of a new cotton-based antimicrobial wipe

USDA-ARS?s Scientific Manuscript database

The adsorption of a cationic biocide on various cotton and synthetic nonwoven fabrics was investigated using UV-Vis absorption spectroscopy. The results reveal that rayon and greige cotton nonwovens adsorb nearly three times more cationic biocide than comparable bleached cotton substrates. Polyester...

40 CFR 469.12 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... methylene chloride naphthalene 2 Nitrophenol phenol bis (2-ethylhexyl) phthalate tetrachloroethylene toluene trichloroethylene 2 Chlorophenol 2,4 Dichlorophenol 4 Nitrophenol pentachlorophenol di-n-butyl phthalate anthracene...

40 CFR 469.12 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... methylene chloride naphthalene 2 Nitrophenol phenol bis (2-ethylhexyl) phthalate tetrachloroethylene toluene trichloroethylene 2 Chlorophenol 2,4 Dichlorophenol 4 Nitrophenol pentachlorophenol di-n-butyl phthalate anthracene...

A high-throughput screen for mitochondrial function reveals known and novel mitochondrial toxicants in a library of environmental agents

PubMed Central

Datta, Sandipan; Sahdeo, Sunil; Gray, Jennifer A.; Morriseau, Christophe; Hammock, Bruce D.; Cortopassi, Gino

2016-01-01

Mitochondrial toxicity is emerging as a major mechanism underlying serious human health consequences. This work performs a high-throughput screen (HTS) of 176 environmental chemicals for mitochondrial toxicity utilizing a previously reported biosensor platform. This established HTS confirmed known mitochondrial toxins and identified novel mitotochondrial uncouplers such as 2, 2′-Methylenebis(4-chlorophenol) and pentachlorophenol. It also identified a mitochondrial ‘structure activity relationship’ (SAR) in the sense that multiple environmental chlorophenols are mitochondrial inhibitors and uncouplers. This study demonstrates proof-of-concept that a mitochondrial HTS assay detects known and novel environmental mitotoxicants, and could be used to quickly evaluate human health risks from mitotoxicants in the environment. PMID:27717841

Degradation of 4-Chlorophenol Under Sunlight Using ZnO Nanoparticles as Catalysts

NASA Astrophysics Data System (ADS)

Rajar, Kausar; Sirajuddin; Balouch, Aamna; Bhanger, M. I.; Sherazi, Tufail H.; Kumar, Raj

2018-03-01

Herein we demonstrate a simplistic microwave assisted chemical precipitation approach regarding the synthesis of zinc oxide nanoparticles. As-prepared ZnO nanoparticles (NPs) were characterized by UV-visible spectroscopy, Fourier transform infra-red spectroscopy, atomic force microscopy and x-ray diffractometry and scrutinized as photo-catalysts for degradation of 4-chlorophenol (4-CP) under sunlight. The study substantiated that 98.5% of 4-CP was degraded within 20 min in the absence of initiator like H2O2 which reflects an outstanding prospective use for ZnO NPs as photo-catalysts. The nanocatalysts were recycled four times and still showed catalytic efficiency up to 95.5% for degradation of 4-CP in the specified 20 min.

[Degradation of 4-chlorophenol in aqueous solution by high-voltage pulsed discharge-ozone technology].

PubMed

Wen, Yuezhong; Jiang, Xuanzhen; Liu, Weiping

2002-03-01

The combination of high voltage pulse discharge and ozonation as an advanced oxidation technology was used to investigate the degradation of 4-chlorophenol (4-CP) in water. The factors that affect the rate of degradation were discussed. The 1.95 x 10(-3) mol/L solutions of 4-CP were almost completely (96%) degraded after the discharge treatment of 30 min. The degradation of 4-CP was investigated as a function of the ozone concentration, radical scavenger and electrode distance. The rate of 4-CP degradation increases with an increase in ozone concentration and a decrease in the electrode distance from 20 mm to 10 mm. The presence of radical scavenger decreased the rate of 4-CP degradation.

3rd International Conference on Stability and Handling of Liquid Fuels

DTIC Science & Technology

1988-12-07

53012, and ( 2 ) the product has no or neglible antimicrobial activity, and (3) FUELSAVER, as is, is of interest for non-military appli- cations. Biocide... antimicrobial action. 101 The active constituents of FUELSAVER are 4-( 2 -nitrobutyl)morpholine, CAS-Reg.No. 2224-44-4 / EINECS No. 2187483, and 4 4’-( 2 ...isothiazoline-3-one, Rohm & Haas Company, Philadelphia Pennsylvania. 5An antimicrobial agent containing 70% 4-( 2 -nitrobutyl)morpholine and 20% 4,4’-( 2 -ethyl- 2

High-Performance Water-Iodinating Cartridge

NASA Technical Reports Server (NTRS)

Sauer, Richard; Gibbons, Randall E.; Flanagan, David T.

1993-01-01

High-performance cartridge contains bed of crystalline iodine iodinates water to near saturation in single pass. Cartridge includes stainless-steel housing equipped with inlet and outlet for water. Bed of iodine crystals divided into layers by polytetrafluoroethylene baffles. Holes made in baffles and positioned to maximize length of flow path through layers of iodine crystals. Resulting concentration of iodine biocidal; suppresses growth of microbes in stored water or disinfects contaminated equipment. Cartridge resists corrosion and can be stored wet. Reused several times before necessary to refill with fresh iodine crystals.

Occurrence of imidacloprid, carbendazim, and other biocides in Italian house dust: Potential relevance for intakes in children and pets.

PubMed

Salis, Severyn; Testa, Cecilia; Roncada, Paola; Armorini, Sara; Rubattu, Nicola; Ferrari, Angelo; Miniero, Roberto; Brambilla, Gianfranco

2017-09-02

The occurrence of pesticides intended for non-agricultural use was investigated in 206 dust samples drawn from vacuum-cleaner bags from residential flats in Italy. The multi-residue analysis targeted on 95 different active principles was performed with UPLC-MS/MS, with a Limit of Quantification (LOQ) of 0.008 μg/g dry weight. The results indicated the presence of imidacloprid (IMI) and carbendazim (CARB) in 30% and 26% of the samples, with a mean and P95 concentration between 1.6 and 39 and between 0.08 and 4.9 μg/g, respectively. Combined presence of two biocides was noted in 19.4% samples, of three biocides in 9.2% samples, of four biocides in 3.4% samples, and of five and six biocides in 0.5% and 1% samples, respectively. According to the estimated dust intake in infants/toddlers aged 6-24 months (16-100 mg d -1 ) and cats (200 mg d -1 ), it was possible to obtain risk characterization with respect to the Acceptable Daily Intake (ADI) for IMI of 0.060 mg/kg body weight (bw) proposed by the European Food Safety Authority (EFSA) and the chronic Population Adjusted Dose (cPAD) of 0.019 mg/kg bw d -1 by US-EPA. Under the worst-case scenario, the presence of IMI in dust indicates potential exceedance of the cPAD in kittens, to be considered as sentinel also accounting for combined exposure. This study highlights the relevance of consumer empowerment about the responsible use of pesticides as biocidal products in indoor environment.

Hemp (Cannabis sativa L.).

PubMed

Feeney, Mistianne; Punja, Zamir K

2015-01-01

Hemp (Cannabis sativa L.) suspension culture cells were transformed with Agrobacterium tumefaciens strain EHA101 carrying the binary plasmid pNOV3635. The plasmid contains a phosphomannose isomerase (PMI) selectable marker gene. Cells transformed with PMI are capable of metabolizing the selective agent mannose, whereas cells not expressing the gene are incapable of using the carbon source and will stop growing. Callus masses proliferating on selection medium were screened for PMI expression using a chlorophenol red assay. Genomic DNA was extracted from putatively transformed callus lines, and the presence of the PMI gene was confirmed using PCR and Southern hybridization. Using this method, an average transformation frequency of 31.23% ± 0.14 was obtained for all transformation experiments, with a range of 15.1-55.3%.

Fluorescence microscopy techniques for quantitative evaluation of organic biocide distribution in antifouling paint coatings: application to model antifouling coatings.

PubMed

Goodes, L R; Dennington, S P; Schuppe, H; Wharton, J A; Bakker, M; Klijnstra, J W; Stokes, K R

2012-01-01

A test matrix of antifouling (AF) coatings including pMMA, an erodible binder and a novel trityl copolymer incorporating Cu₂O and a furan derivative (FD) natural product, were subjected to pontoon immersion and accelerated rotor tests. Fluorescence and optical microscopy techniques were applied to these coatings for quantification of organic biocide and pigment distribution. Total leaching of the biocide from the novel copolymer binder was observed within 6 months of rotor immersion, compared to 35% from the pMMA coating. In pontoon immersions, 61% of the additive was lost from the pMMA coating, and 53% from the erodible binder. Profiles of FD content in the binders revealed an accelerated loss of additive from the surface of the CDP resulting from rosin degradation, compared to even depletion from pMMA. In all samples, release of the biocide was inhibited beyond the Cu₂O front, corresponding to the leached layer in samples where Cu₂O release occurred.

Electrochemical Disinfection Feasibility Assessment Materials Evaluation for the International Space Station

NASA Technical Reports Server (NTRS)

Rodriquez, Branelle; Shindo, David; Montgomery, Eliza

2013-01-01

The International Space Station (ISS) Program recognizes the risk of microbial contamination in their potable and non-potable water sources. The end of the Space Shuttle Program limited the ability to send up shock kits of biocides in the event of an outbreak. Currently, the United States Orbital Segment water system relies primarily on iodine to mitigate contamination concerns, which has been successful in remediating the small cases of contamination documented. However, a secondary method of disinfection is a necessary investment for future space flight. Over the past year, NASA Johnson Space Center has investigated the development of electrochemically generated systems for use on the ISS. These systems include: hydrogen peroxide, ozone, sodium hypochlorite, and peracetic acid. To use these biocides on deployed water systems, NASA must understand of the effect these biocides have on current ISS materials prior to proceeding forward with possible on-orbit applications. This paper will discuss the material testing that was conducted to assess the effects of the biocides on current ISS materials.

Biogenic nanosilica blended by nanofibrillated cellulose as support for slow-release of tebuconazole

NASA Astrophysics Data System (ADS)

Mattos, Bruno D.; Magalhães, Washington L. E.

2016-09-01

Despite the potential application of nanotechnology in the agricultural sector, it is not as competitive as other industrial sectors because these approaches do not demonstrate a sufficient economic return to counterbalance the high production costs. For biocidal purposes, the reduction of the initial costs can be addressed if biogenic nanosilica and nanofibrillated cellulose were used to prepare nanocomposite for further utilization as support for slow-release of tebuconazole. Infrared spectroscopy and thermogravimetric analysis revealed that biocide was entrapped in the cellulose/silica nanocomposites network. The scanning electron microscopy and X-ray microtomography evaluation showed the nanocomposite's microstructure based on irregular shape nanosilica blended by nanofibrillated cellulose in a randomly organized network. Elemental mapping images showed the tebuconazole better dispersed in the composite blended with lower content of cellulose. The nanofibrillated cellulose played an important role in the release rate of the biocide mainly at short-term periods. At 15 days of immersion, the pure biocide had 95 % release compared with 30-45 % release of the tebuconazole loaded in the nanocomposites.

How representative is pesticide monitoring in Swiss streams?

NASA Astrophysics Data System (ADS)

Munz, Nicole; Wittmer, Irene; Strahm, Ivo; Leu, Christian; Stamm, Christian

2013-04-01

The surveillance of surface water quality in Switzerland is the task of the 26 cantons. This includes the assessment of the level of pesticide pollution. Each of the cantons may follow different procedures, which makes a comparison difficult and cumbersome. Nevertheless, in this study presents the main results of the first nation-wide compilation and interpretation of cantonal and federal monitoring data as well as results from specific research projects on agricultural and urban pesticides are presented. Overall, more than 345'000 concentration data of 281 biocidal compounds have been analyzed. This set of substances includes 203 compounds that have been registered either only as agricultural plant protection (N = 149) product or only as urban biocide (N = 18), but also some (N = 36) which were registered for both uses. This data set contains 70 out of the 100 most sold agricultural plant protection products in 2010. A comparable assessment for the representativeness of the biocide data is hardly possible due to a lack of systematic use data. The data stem from 565 measuring sites. However, these sites are not representative for all size classes of the Swiss stream network. While about 75% of the total length of the stream network is made up by small streams (Strahler order 1 and 2), only 28% of the measuring sites are located on such streams. In combination with the sampling strategies that have been used - about 50% grab samples and 50% composite samples - it can be concluded that the 2% of measured values > 100 ng L-1 most probably severely underestimates the true level of pesticide pollution in the Swiss stream network. In the future, more emphasis has to be put on small streams, where higher concentrations are expected and thus also actual ecological effects.

Toxic indole alkaloids avrainvillamide and stephacidin B produced by a biocide tolerant indoor mold Aspergillus westerdijkiae.

PubMed

Mikkola, Raimo; Andersson, Maria A; Hautaniemi, Maria; Salkinoja-Salonen, Mirja S

2015-06-01

Toxic Aspergillus westerdijkiae were present in house dust and indoor air fall-out from a residence and a kindergarten where the occupants suffered from building related ill health. The A. westerdijkiae isolates produced indole alkaloids avrainvillamide (445 Da) and its dimer stephacidin B (890 Da). It grew and sporulated in presence of high concentrations of boron or polyguanidine (PHMB, PHMG) based antimicrobial biocides used to remediate mold infested buildings. The boar sperm cells were used as sensor cells to purify toxins from HPLC fractions of the fungal biomass. Submicromolar concentrations (EC50 0.3-0.4 μM) blocked boar spermatozoan motility and killed porcine kidney tubular epithelial cells (PK-15). Plate grown hyphal mass of the A. westerdijkiae isolates contained 300-750 ng of avrainvillamide and 30-300 ng of stephacidin B per mg (wet weight). The toxins induced rapid (30 min) loss of boar sperm motility, followed (24 h) by loss of mitochondrial membrane potential (ΔΨm). Apoptotic cell death was observed in PK-15 cell monolayers, prior to cessation of glucose uptake or loss of ΔΨm. Avrainvillamide and stephacidin B were 100-fold more potent towards the porcine cells than the mycotoxins stephacidin A, ochratoxin A, sterigmatocystin and citrinin. The high toxicity of stephacidin B indicates a role of nitrone group in the mechanism of toxicity. Avrainvillamide and stephacidin B represent a new class of toxins with possible a threat to human health in buildings. Furthermore, the use of biocides highly enhanced the growth of toxigenic A. westerdijkiae. Copyright © 2015 Elsevier Ltd. All rights reserved.

Common hydraulic fracturing fluid additives alter the structure and function of anaerobic microbial communities

USGS Publications Warehouse

Mumford, Adam C.; Akob, Denise M.; Klinges, J. Grace; Cozzarelli, Isabelle M.

2018-01-01

The development of unconventional oil and gas (UOG) resources results in the production of large volumes of wastewater containing a complex mixture of hydraulic fracturing chemical additives and components from the formation. The release of these wastewaters into the environment poses potential risks that are poorly understood. Microbial communities in stream sediments form the base of the food chain and may serve as sentinels for changes in stream health. Iron-reducing organisms have been shown to play a role in the biodegradation of a wide range of organic compounds, and so to evaluate their response to UOG wastewater, we enriched anaerobic microbial communities from sediments collected upstream (background) and downstream (impacted) of an UOG wastewater injection disposal facility in the presence of hydraulic fracturing fluid (HFF) additives: guar gum, ethylene glycol, and two biocides, 2,2-dibromo-3-nitrilopropionamide (DBNPA) and bronopol (C3H6BrNO4). Iron reduction was significantly inhibited early in the incubations with the addition of biocides, whereas amendment with guar gum and ethylene glycol stimulated iron reduction relative to levels in the unamended controls. Changes in the microbial community structure were observed across all treatments, indicating the potential for even small amounts of UOG wastewater components to influence natural microbial processes. The microbial community structure differed between enrichments with background and impacted sediments, suggesting that impacted sediments may have been preconditioned by exposure to wastewater. These experiments demonstrated the potential for biocides to significantly decrease iron reduction rates immediately following a spill and demonstrated how microbial communities previously exposed to UOG wastewater may be more resilient to additional spills.

Comparing the biocidal properties of non-thermal plasma sources by reference protocol

NASA Astrophysics Data System (ADS)

Khun, Josef; Jirešová, Jana; Kujalová, Lucie; Hozák, Pavel; Scholtz, Vladimír

2017-10-01

The previously proposed reference protocol enabling easy comparison of biocidal properties of different non-thermal plasma sources has been followed and discussed. For inactivation tests the reference protocol has used spores of Gram positive bacterium Bacillus subtilis (ATCC 6633) deposited on a polycarbonate membrane as reference sample. In this work, biocidal properties of a negative glow corona, positive streamer corona, positive transient spark and cometary discharges are being compared in both open air and closed apparatus. Despite the total number of bacteria surviving 1 h exposure has decreased by up to 7 orders in closed apparatus, in open one, only weak inhibition bactericidal effect has been observed.

Biofilms and Oxidizing Biocides; Evaluation of Disinfection and Removal Effects by Using Established Microbial Systems.

PubMed

Tachikawa, Mariko

2017-01-01

The formation of bacterial biofilms and their disinfection and removal have been important subjects in the maintenance of water quality in areas such as public spas, swimming pools, food processing lines, industrial water systems, and in the hygienic control of medical devices, hospital procedures, etc. Presented here is an outline of biofilm formation, as well as studies on the disinfection and removal of biofilms by oxidizing biocides using established biofilms. These studies using established biofilms may increase the understanding of the variable response of biofilms to planktonic bacteria, and the unique aspects of oxidizing biocides in the disinfection and removal of biofilms.

40 CFR 469.22 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... trichloroethylene 2 Chlorophenol 2,4 Dichlorophenol 4 Nitrophenol pentachlorophenol di-n-butyl phthalate anthracene 1,2 Diphenylhydrazine isophorone butyl benzyl pthalate 1,1 Dichloroethylene 2,4,6 Trichlorophenol...

40 CFR 469.22 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... trichloroethylene 2 Chlorophenol 2,4 Dichlorophenol 4 Nitrophenol pentachlorophenol di-n-butyl phthalate anthracene 1,2 Diphenylhydrazine isophorone butyl benzyl pthalate 1,1 Dichloroethylene 2,4,6 Trichlorophenol...

THE REMOVAL OF INVASIVE SPECIES THROUGH GENE SILENCING IN MICROALGAE CULTIVATION FOR BIODIESEL

EPA Science Inventory

The successful completion of this project will be a significant advancement in promoting a domestic supply of sustainable biodiesel. Additionally, the “green” biocide proposed in this project is significantly less toxic to the environment compared to current biocides and algae...

The aluminium and iodine pentoxide reaction for the destruction of spore forming bacteria.

PubMed

Clark, Billy R; Pantoya, Michelle L

2010-10-21

The threat of biological weapons is a major concern in the present day and has led to studying methods to neutralize spore forming bacteria. A new technique involves the use of a thermite reaction that exhibits biocidal properties to limit bacterial growth. The objective was to examine the influence on bacteria growth upon spore exposure to thermite reactions with and without biocidal properties. Three thermites are considered: two that have biocidal properties (aluminium (Al) combined with iodine pentoxide (I(2)O(5)) and Al combined with silver oxide (Ag(2)O)); and, one that produces a highly exothermic reaction but has no biocidal properties (Al combined with iron oxide (Fe(2)O(3))). Results show that Al + I(2)O(5) is extremely effective at neutralizing spores after only one hour of exposure. The temperature generated by the reaction was not determined to be an influential factor affecting spore growth kinetics. Further analysis of the thermite reactions revealed that the Al + I(2)O(5) reaction produces iodine gas that effectively interacts with the spores and neutralizes bacteria growth, while the Al + Ag(2)O reaction temperature does not vaporize silver. In the condensed phase silver does not interact with the spores enough to neutralize bacteria growth. This study gives evidence that a thermite can be used as a stable transportation and delivery system for biocidal gas.

Fate of hydraulic fracturing chemicals under down-hole conditions

NASA Astrophysics Data System (ADS)

Blotevogel, J.; Kahrilas, G.; Corrin, E. R.; Borch, T.

2013-12-01

Hydraulic fracturing is a method to increase the yield of oil and natural gas extraction from unconventional rock formations. The process of hydrofracturing occurs via injecting water, sand, and chemicals into the production well and subjecting this mixture to high pressures to crack the rock shale, allowing increased amounts of gas and oil to seep out of the target formation. Typical constituents of the chemical mixtures are biocides, which are applied to inhibit growth of sulfate reducing bacteria in order to prevent pipe corrosion and production of hazardous gases. However, very little is known about the persistence, fate, and activity of biocides when subjected to the high temperatures and pressures of down-hole conditions. Thus, the objective of this talk is to present data from ongoing experiments focused on determining the fate of biocides commonly used for hydraulic fracturing under conditions simulating down-hole environments. Using stainless steel reactors, the high pressures and temperatures of down-hole conditions in the Marcellus shale are simulated, while concentration, speciation, and degradation of priority biocides are observed as a function of time, using primarily LC/MS techniques. The impact of water quality, shale, temperature, and pressure on the transformation kinetics and pathways of biocides will be discussed. Finally, field samples (both sediments and flowback brine) from the Marcellus shale are analyzed to verify that our lab simulations mirror real-life conditions and results.

Quantitative comparison of the results obtained by the multiple-dose guinea pig maximization test and the non-radioactive murine local lymph-node assay for various biocides.

PubMed

Yamano, Tetsuo; Shimizu, Mitsuru; Noda, Tsutomu

2005-07-01

We compared the results of the multiple-dose guinea pig maximization test (GPMT) and the non-radioactive murine local lymph-node assay (LLNA) for various biocides. Thirteen out of 17 positive biocides in the GPMT gave positive results in the LLNA. In the GPMT, the minimum first induction doses ranged over four orders (0.00005-0.5%), while elicitation-threshold doses, which were evaluated using an optimally sensitized group of animals in the multiple-dose studies, ranged over five orders (0.00006-2.8%). In the LLNA, minimum induction doses ranged over more than three orders (0.01-30%). With respect to 13 biocides that were positive in both the GPMT and the LLNA, results were quantitatively compared. When compared after conversion to corresponding area doses (microg/cm), the minimum doses required to elicit skin reaction in guinea pigs were always lower than that for induction in mice with all biocides. Correlation between minimum induction doses from the GPMT and the LLNA seemed poor (r=0.57), while that between minimum induction doses in the LLNA and elicitation-threshold doses in the GPMT was relatively good (r=0.73). The results suggest the possibility to estimate human elicitation-threshold doses, which are definitely lacking in the process of risk assessment for skin-sensitizers, from the data of the LLNA.

Antibacterial surface design - Contact kill

NASA Astrophysics Data System (ADS)

Kaur, Rajbir; Liu, Song

2016-08-01

Designing antibacterial surfaces has become extremely important to minimize Healthcare Associated Infections which are a major cause of mortality worldwide. A previous biocide-releasing approach is based on leaching of encapsulated biocides such as silver and triclosan which exerts negative impacts on the environment and potentially contributes to the development of bacterial resistance. This drawback of leachable compounds led to the shift of interest towards a more sustainable and environmentally friendly approach: contact-killing surfaces. Biocides that can be bound onto surfaces to give the substrates contact-active antibacterial activity include quaternary ammonium compounds (QACs), quaternary phosphoniums (QPs), carbon nanotubes, antibacterial peptides, and N-chloramines. Among the above, QACs and N-chloramines are the most researched contact-active biocides. We review the engineering of contact-active surfaces using QACs or N-chloramines, the modes of actions as well as the test methods. The charge-density threshold of cationic surfaces for desired antibacterial efficacy and attempts to combine various biocides for the generation of new contact-active surfaces are discussed in detail. Surface positive charge density is identified as a key parameter to define antibacterial efficacy. We expect that this research field will continue to attract more research interest in view of the potential impact of self-disinfective surfaces on healthcare-associated infections, food safety and corrosion/fouling resistance required on industrial surfaces such as oil pipes and ship hulls.

Atmospheric oxidation mechanism of chlorobenzene.

PubMed

Wu, Runrun; Wang, Sainan; Wang, Liming

2014-09-01

The atmospheric oxidation mechanism of chlorobenzene (CB) initiated by the OH radicals is investigated at M06-2X/6-311++G(2df, 2p) and ROCBS-QB3 levels. The oxidation is initiated by OH addition to the ortho (∼50%), para (∼33%) and meta (∼17%) positions, forming CB-OH adducts as R2, R3, and R4; while the ipso-addition is negligible (∼0.2%). The reactions of the CB-OH adducts with the atmospheric oxygen are further investigated in detail by coupling the unimolecular reaction rate theory calculations with master-equation (RRKM-ME). The CB-OH adducts react with O2 either by irreversible H-abstraction to form chlorophenol and HO2 or by reversible additions to form CB-OH-O2 radicals, which subsequently cyclize to bicyclic radicals. RRKM-ME calculations show that the addition reactions of CB-OH and O2 at the atmospheric pressure are close to but not yet reach their high-pressure-limits. The RRKM-ME simulations predict the yields of 93%, 38%, and 74% for ortho-, meta- and para-chlorophenols from the reactions of O2 with R2, R3 and R4, being lower than their high-pressure-limit yields of 95%, 48%, an 80%, respectively. Overall, the yield of chlorophenols is determined as 72% at the atmospheric pressure. Copyright © 2014 Elsevier Ltd. All rights reserved.

Chlorination Revisited: Does Cl- Serve as a Catalyst in the Chlorination of Phenols?

PubMed

Lau, Stephanie S; Abraham, Sonali M; Roberts, A Lynn

2016-12-20

The aqueous chlorination of (chloro)phenols is one of the best-studied reactions in the environmental literature. Previous researchers have attributed these reactions to two chlorine species: HOCl (at circum-neutral and high pH) and H 2 OCl + (at low pH). In this study, we seek to examine the roles that two largely overlooked chlorine species, Cl 2 and Cl 2 O, may play in the chlorination of (chloro)phenols. Solution pH, chloride concentration, and chlorine dose were systematically varied in order to assess the importance of different chlorine species as chlorinating agents. Our findings indicate that chlorination rates at pH < 6 increase substantially when chloride is present, attributed to the formation of Cl 2 . At pH 6.0 and a chlorine dose representative of drinking water treatment, Cl 2 O is predicted to have at best a minor impact on chlorination reactions, whereas Cl 2 may contribute more than 80% to the overall chlorination rate depending on the (chloro)phenol identity and chloride concentration. While it is not possible to preclude H 2 OCl + as a chlorinating agent, we were able to model our low-pH data by considering Cl 2 only. Even traces of chloride can generate sufficient Cl 2 to influence chlorination kinetics, highlighting the role of chloride as a catalyst in chlorination reactions.

Linking the Physicochemical Properities of Titania with Its Biocidal Properities

EPA Science Inventory

LINKING THE PHYSICOCHEMICAL PROPERTIES OF TITANIA WITH ITS BIOCIDAL PROPERTIES. C. Han1, L. Putvin2, M. Pelaez1, H. Zamankhan3, H. Choi3, D. Betancourt4a, D. Dionysiou1. B. Veronesi4b, 1 Department of Biomedical, Chemical and Environmental Engineering, University of Cincinnati...

Limiting sucrose loss in Louisiana raw sugar factories: Are biocides necessary?

USDA-ARS?s Scientific Manuscript database

Sucrose deterioration takes place post-harvest in sugarcane, and is a significant problem for the sugar industry. In Louisiana, the majority of sucrose destruction occurs when cane is stock piled in mill yards and during overnight truck sleeper loads. Biocides are used in Louisiana raw sugarcane fac...

INVESTIGATION OF GAS-PHASE OZONE AS A POTENTIAL BIOCIDE

EPA Science Inventory

The paper presents data on the effect of ozone on both vegetative and spore-forming fungi as well as on spore-forming bacteria. (NOTE: Despite the wide use of ozone generators in indoor air cleaning, there is little research data on ozone's biocidal activity in the gas phase.) Dr...

120 years of nanosilver history: implications for policy makers.

PubMed

Nowack, Bernd; Krug, Harald F; Height, Murray

2011-02-15

Nanosilver is one nanomaterial that is currently under a lot of scrutiny. Much of the discussion is based on the assumption that nanosilver is something new that has not been seen until recently and that the advances in nanotechnology opened completely new application areas for silver. However, we show in this analysis that nanosilver in the form of colloidal silver has been used for more than 100 years and has been registered as a biocidal material in the United States since 1954. Fifty-three percent of the EPA-registered biocidal silver products likely contain nanosilver. Most of these nanosilver applications are silver-impregnated water filters, algicides, and antimicrobial additives that do not claim to contain nanoparticles. Many human health standards for silver are based on an analysis of argyria occurrence (discoloration of the skin, a cosmetic condition) from the 1930s and include studies that considered nanosilver materials. The environmental standards on the other hand are based on ionic silver and may need to be re-evaluated based on recent findings that most silver in the environment, regardless of the original silver form, is present in the form of small clusters or nanoparticles. The implications of this analysis for policy of nanosilver is that it would be a mistake for regulators to ignore the accumulated knowledge of our scientific and regulatory heritage in a bid to declare nanosilver materials as new chemicals, with unknown properties and automatically harmful simply on the basis of a change in nomenclature to the term "nano".

25 CFR 166.312 - Is a conservation plan required?

Code of Federal Regulations, 2010 CFR

2010-04-01

... Operations Management Management Plans and Environmental Compliance § 166.312 Is a conservation plan required... resource management plan and must address the permittee's management objectives regarding animal husbandry...

Summary Factsheets for Pesticide Permittees

EPA Pesticide Factsheets

Summaries of the 2016 Pesticide General Permit (PGP) requirements and provisions covering mosquito and other flying insect pest control; weed and algae pest control; animal pest control; and forest canopy pest control.

47 CFR 74.1269 - Copies of rules.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., AUXILIARY, SPECIAL BROADCAST AND OTHER PROGRAM DISTRIBUTIONAL SERVICES FM Broadcast Translator Stations and FM Broadcast Booster Stations § 74.1269 Copies of rules. The licensee or permittee of a station...

40 CFR 172.6 - Labeling.

Code of Federal Regulations, 2010 CFR

2010-07-01

...”; (4) The name, brand, or trademark; (5) The name and address of the permittee, producer, or registrant... a registered pesticide, the Administrator may, at his discretion, permit a pesticide to be used...

25 CFR 167.8 - Grazing rights.

Code of Federal Regulations, 2011 CFR

2011-04-01

... ownership records as established in accordance with § 167.7 or who have acquired grazing rights by marriage..., separation, threatened family disruption, and permits of deceased permittees shall be the responsibility of...

25 CFR 167.8 - Grazing rights.

Code of Federal Regulations, 2014 CFR

2014-04-01

... ownership records as established in accordance with § 167.7 or who have acquired grazing rights by marriage..., separation, threatened family disruption, and permits of deceased permittees shall be the responsibility of...

25 CFR 167.8 - Grazing rights.

Code of Federal Regulations, 2013 CFR

2013-04-01

... ownership records as established in accordance with § 167.7 or who have acquired grazing rights by marriage..., separation, threatened family disruption, and permits of deceased permittees shall be the responsibility of...

25 CFR 167.8 - Grazing rights.

Code of Federal Regulations, 2012 CFR

2012-04-01

... ownership records as established in accordance with § 167.7 or who have acquired grazing rights by marriage..., separation, threatened family disruption, and permits of deceased permittees shall be the responsibility of...

40 CFR 144.53 - Schedule of compliance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... permittee may cease conducting regulated activities (by plugging and abandonment) rather than continue to... public commitment satisfactory to the Director, such as a resolution of the board of directors of a...

40 CFR 144.53 - Schedule of compliance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... permittee may cease conducting regulated activities (by plugging and abandonment) rather than continue to... public commitment satisfactory to the Director, such as a resolution of the board of directors of a...

40 CFR 144.53 - Schedule of compliance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... permittee may cease conducting regulated activities (by plugging and abandonment) rather than continue to... public commitment satisfactory to the Director, such as a resolution of the board of directors of a...

40 CFR 144.53 - Schedule of compliance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... permittee may cease conducting regulated activities (by plugging and abandonment) rather than continue to... public commitment satisfactory to the Director, such as a resolution of the board of directors of a...

40 CFR 144.53 - Schedule of compliance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... permittee may cease conducting regulated activities (by plugging and abandonment) rather than continue to... public commitment satisfactory to the Director, such as a resolution of the board of directors of a...

40 CFR 421.21 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Aluminum Smelting Subcategory § 421... apply to this subpart. (b) The term product shall mean hot aluminum metal. (c) If a permittee chooses to...

25 CFR 167.7 - Records.

Code of Federal Regulations, 2010 CFR

2010-04-01

... and assist in organizing the sheep and goat dipping and horse and cattle branding program and... sheep and goats and at branding and tallying points for cattle and horses. Should the permittee be...