Conductance Steamflow relationship

DOE Data Explorer

Whitney Trainor-Guitton

2015-04-01

These histograms represent our calibration of conductance of a volcanic geothermal field (with a clay cap) and the observed steam flow rates. See the following paper for further description: Trainor-Guitton, Hoversten,Nordquist, Intani, Value of information analysis using geothermal field data: accounting for multiple interpretations & determining new drilling locations. SEG Abstracts 2015.

Strength and Deformation Behaviour of Cap Rocks Above the CO2SINK-Reservoir

NASA Astrophysics Data System (ADS)

Mutschler, T.; Triantafyllidis, T.; Balthasar, K.; Norden, B.

2009-04-01

The cap-rock of the CO2SINK storage site close to Ketzin consists of clay rich rocks which are typical for cap rock formations above CO2 storage reservoirs. The strength and deformation behaviour of such claystone samples are therefore of fundamental importance for the characterization of secure geological storage of CO2. The elastic and anelastic deformation behaviour limits the maximum injection pressure during CO2-injection and is part of the security measures for the long term storage of CO2. The laboratory experiments where performed on samples gathered from the injection well of the Ketzin pilot test site in Germany and are compared with the elastic and anelastic behaviour of samples from the same Keuper formation in a near-surface outcrop in the Southwest of Germany showing a similar lithology. The samples from the outcrop allowed drilling of samples with a standard size of 100 mm diameter and 200 mm height as well as large samples with a diameter of 550 mm and a height of 1200 mm. The investigations have a special emphasis on the viscous behaviour of the clay stones and its scaling behaviour. A special triaxial testing procedure is applied both on standard and large size samples allowing the determination of the strength, stiffness and viscosity behaviour of the rock in one experimental run. Multi-stage technique (stepwise variation of the confining pressure) gives the strength behaviour of each single sample while applying a constant deformation rate. Stepwise varied deformation rates on the other hand lead to steps in the stress-strain-curve from which the viscosity index is determined. The viscosity index is directly used in the Norton's constitutive relations for viscoplastic simulations. The combination of tests allows for the determination of a broad range of elastic and anelastic properties. The comparison of results - both for elastic and anelastic behaviour - from standard and large samples shows that for the examined rocks a scale effect is negligible. Transition from cataclastic to non-cataclastic behaviour - the transition limit - occurs in a similar range of applied levels of pressure and deformation rates even at room temperature. The obtained transition limit is very important for the judgment of the sealing capacity and integrity of the cap rock. The deformation rates predicted for the pressure and temperature conditions of the caprock at Ketzin test site are far beneath the determined transition limit during the injection and after stop of injection. As a 0° friction angle is used for pressure and deformation limit at Ketzin, the measured elastic and anelastic behaviour of the real caprock act as additional safety margin during injection and in the post injection phase. As the examined rocks are typical for many possible storage sites, the discussed results are of importance beyond the Ketzin Pilot Experiment CO2SINK.

Effect of alternative surface inlet designs on sediment and phosphorus drainage losses

USDA-ARS?s Scientific Manuscript database

Open surface inlets that connect to subsurface tile drainage systems provide a direct pathway for sediment, nutrients, and agrochemicals to surface waters. This study was conducted to determine whether modifying open inlets by burying them in gravel capped with 30 cm of sandy clay loam soil or in ve...

Testing the shorter and variable recurrence interval hypothesis along the Cholame segment of the San Andreas Fault

NASA Astrophysics Data System (ADS)

Williams, A.; Arrowsmith, R.; Rockwell, T. K.; Akciz, S. O.; Grant Ludwig, L.

2016-12-01

The Cholame segment of the San Andreas Fault interacts with the Parkfield segment to the northwest with its creep and M6 earthquakes and the locked Carrizo segment to the southeast. Although offset reconstructions exist for this 75 km reach, rupture behavior is poorly characterized, limiting seismic hazard evaluation. Here we present new paleoseismic results from 2 fault perpendicular 26 m long trenches connected by a 15 m long fault parallel trench. The site is located south of the Parkfield segment 20 km southeast of Highway 46. Site geomorphology is characterized by several 50 m offset drainages northwest of the trenches, small shutter ridges and sag ponds, and alluvial fans crossing the fault. Fault zone stratigraphy consists of alternating finely bedded sands, silts, and gravels, and bioturbated soil horizons. The strata record 3-4 earthquakes and possible deformation post-1857, similar to the LY4 site 38 km southeast. E4, E3 and the most recent earthquake (MRE) are well supported by evidence of decreasing vertical offset up-sequence, capped fissure fill and colluvial wedges, which create small horst and graben structures. Units display vertical offsets ranging from 60 cm at the base to 12 cm near the MRE horizon, small colluvial wedges, and sag deposits within the 4 m wide fault zone. E2—the penultimate-is less certain, supported only by the decreasing offset in the stratigraphic sequence. The E4 event horizon is a gradational clayey silt sag deposit capped by discontinuous gravel, 18 cm at its thickest point and extending 4.8 m across the fault zone. The E3 and E2 event horizons are capped by thin bedded silty clay, and bounded by discontinuous burn horizons. The MRE horizon extends 6 m across the main fault zone, and consists of a silty clay sag deposit capped by very fine, bedded sand and coarse gravel, 22 cm at its thickest point and overlying a burn horizon. If the MRE is indeed the 1857 event, it has significant potential in correlation with the high quality rupture records at Bidart (70 km southeast), and Frazier Mountain (180 km southeast). This site contains abundant detrital charcoal in many of the units and burn horizons at or near event horizons providing great potential for bracketing the age of these paleoearthquakes.

Effect of replacing surface inlets with blind or gravel inlets on sediment and phosphorus subsurface drainage losses

USDA-ARS?s Scientific Manuscript database

Open surface inlets that connect to subsurface tile drainage systems provide a direct pathway for sediment, nutrients, and agrochemicals to surface waters. This study was conducted to determine whether modifying open inlets by burying them in gravel capped with 30 cm of sandy clay loam soil or in ve...

Biodiversity of mycorrhizas on Garry oak (Quercus garryana) in a southern Oregon savanna

Treesearch

Lori L. Valentine; Tina L. Fiedler; Stephen R. Haney; Harold K. Berninghausen; Darlene Southworth

2002-01-01

Garry oak or Oregon white oak (Quercus garryana) is the dominant vegetation on the Whetstone Savanna in Jackson County, Oregon. The site is located on the western edge of the Agate Desert, an alluvial fan capped with shallow clay loam over a cemented hardpan. The landform exhibits patterned ground with mounds and vernal pools. The oaks are associated...

Stand Parameters of 11- to 15-Year Old Green Ash Plantings

Treesearch

Roger M. Krinard

1989-01-01

Three green ash (Fraxinus pennsylvanica Marsh.) plantings, ages 11, 13, and 15, and a 13-year-old pumpkin ash (F. profunda (Bush) Bush) planting were sampled to determine d.b.h. and height development and survival of free-to-grow trees. On medium-textured (Commerce) and clay-capped (Bowdre and Tunica) soils, the average d.b.h...

2,4,6-Trinitrotoluene in soil and groundwater under a waste lagoon at the former Explosives Factory Maribyrnong (EFM), Victoria, Australia

NASA Astrophysics Data System (ADS)

Martel, Richard; Robertson, Timothy James; Doan, Minh Quan; Thiboutot, Sonia; Ampleman, Guy; Provatas, Arthur; Jenkins, Thomas

2008-01-01

Energetic materials contamination was investigated at the former Explosives Factory Maribyrnong, Victoria, Australia. Spectrophotometric/high performance liquid chromatography (HPLC) analysis was utilised to delineate a 5 tonne crystalline 2,4,6-trinitrotoluene (TNT) source in a former process waste lagoon that was found to be supplying contaminant leachate to the surficial clay aquitard with a maximum-recorded concentration of 7.0 ppm TNT. Groundwater within underlying sand and gravel aquifers was found to be uncontaminated due to upward hydraulic gradients resulting in slow plume development and propagation. Adsorption and microcosm test results from a parallel study were used as input parameters to simulate aqueous TNT transport in the clay aquitard using ATRANS20 software. The simulated TNT plume was localised within a few metres of the source, and at steady state, though leaching rate calculations suggest that without mitigation or other changes to the system, persistence of the source would be approximately 2,000 years. Remediation strategies may involve removal of the near surface source zone and infilling with an impermeable capping to impede leaching while facilitating ongoing natural attenuation by anaerobic degradation.

Willow water uptake and shoot extension growth in response to nutrient and moisture on a clay landfill cap soil.

PubMed

Martin, Peter J; Stephens, William

2008-09-01

Extension growth of willow (Salix viminalis L.) and changes in soil water were measured in lysimeters containing clay and sandy loam soils with different amendment and watering treatments. No water uptake was found below 0.3m in the nutritionally poor unamended clay; amendment with organic matter to 0.4m depth resulted in water extraction down to 0.5m depth whereas in the sandy loam, there was greater extraction from all depths down to 0.6m. With water stress, wilting of plants occurred when the volumetric soil water content at 0.1m was about 31% in the clay and 22% in the sandy loam. Compared with shoots on plants in the amended clay, those in the unamended treatment showed reduced extension growth, little increase in stem basal area (SBA) and a small shoot leaf area, resulting from a reduced number of leaves shoot(-1) and a small average area leaf(-1). Water stress also reduced shoot extension growth, SBA gain and the leaf area on extension growth. Shoot growth rates were significantly correlated with air temperature and base temperatures between 2.0 and 7.6 degrees C were indicated for the different treatments. These studies have helped to explain some of the large treatment effects described previously on biomass production and plant leaf area.

A comparative study of internally and externally capped balloons using small scale test balloons

NASA Technical Reports Server (NTRS)

Bell, Douglas P.

1994-01-01

Caps have been used to structurally reinforce scientific research balloons since the late 1950's. The scientific research balloons used by the National Aeronautics and Space Administration (NASA) use internal caps. A NASA cap placement specification does not exist since no empirical information exisits concerning cap placement. To develop a cap placement specification, NASA has completed two in-hangar inflation tests comparing the structural contributions of internal caps and external caps. The tests used small scale test balloons designed to develop the highest possible stresses within the constraints of the hangar and balloon materials. An externally capped test balloon and an internally capped test balloon were designed, built, inflated and simulated to determine the structural contributions and benefits of each. The results of the tests and simulations are presented.

A Laboratory Experiment for the Statistical Evaluation of Aerosol Retrieval (STEAR) Algorithms

NASA Astrophysics Data System (ADS)

Schuster, G. L.; Espinosa, R.; Ziemba, L. D.; Beyersdorf, A. J.; Rocha Lima, A.; Anderson, B. E.; Martins, J. V.; Dubovik, O.; Ducos, F.; Fuertes, D.; Lapyonok, T.; Shook, M.; Derimian, Y.; Moore, R.

2016-12-01

We have developed a method for validating Aerosol Robotic Network (AERONET) retrieval algorithms by mimicking atmospheric extinction and radiance measurements in a laboratory experiment. This enables radiometric retrievals that utilize the same sampling volumes, relative humidities, and particle size ranges as observed by other in situ instrumentation in the experiment. We utilize three Cavity Attenuated Phase Shift (CAPS) monitors for extinction and UMBC's three-wavelength Polarized Imaging Nephelometer (PI-Neph) for angular scattering measurements. We subsample the PI-Neph radiance measurements to angles that correspond to AERONET almucantar scans, with solar zenith angles ranging from 50 to 77 degrees. These measurements are then used as input to the Generalized Retrieval of Aerosol and Surface Properties (GRASP) algorithm, which retrieves size distributions, complex refractive indices, single-scatter albedos (SSA), and lidar ratios for the in situ samples. We obtained retrievals with residuals R < 10% for 100 samples. The samples that we tested include Arizona Test Dust, Arginotec NX, Senegal clay, Israel clay, montmorillonite, hematite, goethite, volcanic ash, ammonium nitrate, ammonium sulfate, and fullerene soot. Samples were alternately dried or humidified, and size distributions were limited to diameters of 1.0 or 2.5 um by using a cyclone. The SSA at 532 nm for these samples ranged from 0.59 to 1.00 when computed with CAPS extinction and PSAP absorption measurements. The GRASP retrieval provided SSAs that are highly correlated with the in situ SSAs, and the correlation coefficients ranged from 0.955 to 0.976, depending upon the simulated solar zenith angle. The GRASP SSAs exhibited an average absolute bias of +0.023 +/-0.01 with respect to the extinction and absorption measurements for the entire dataset. Although our apparatus was not capable of measuring backscatter lidar ratio, we did measure bistatic lidar ratios at a scattering angle of 173 deg. The GRASP bistatic lidar ratios had correlations of 0.488 to 0.735 (depending upon simulated SZA) with respect to in situ measurements, positive relative biases of 6-10%, and average absolute biases of 4.0-6.6 sr. We also compared the GRASP size distributions to aerodynamic particle size measurements.

Effectiveness of Sealed Double-Ring Infiltrometers{trademark} and effects of changes in atmospheric pressure on hydraulic conductivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMullin, S.R.

The Savannah River Site is currently evaluating some 40 hazardous and radioactive-waste sites for remediation. Among the remedial alternatives considered is closure using a kaolin clay cap. The hydraulic conductivity suggested by the US Environmental Protection Agency is 1.0 {times} 10{sup {minus}7} cm/sec. One instrument to measure this value is the Sealed Double-Ring Infiltrometer{trademark} (SDRI). Six SDRI were recently installed on a kaolin test cap. Test results demonstrated uniform performance of these instruments. However, the test data showed as much as an order of magnitude of variation over time. This variation is attributed to both internal structural heterogeneity and variablemore » external boundary conditions. The internal heterogeneity is caused by construction variability within a specified range of moisture and density. The external influences considered are temperature and barometric pressure. Temperature was discharged as a source of heterogeneity because of a lack of correlation with test data and a negligible impact from the range of variability. However, a direct correlation was found between changes in barometric pressure and hydraulic conductivity. This correlation is most pronounced when pressure changes occur over a short period of time. Additionally, this correlation is related to a single soil layer. When the wetting front passes into a more porous foundation layer, the correlation with pressure changes disappears. Conclusions are that the SDRI performs adequately, with good repeatability of results. The duration of test is critical to assure a statistically valid data set. Data spikes resulting from pressure changes should be identified, and professional judgment used to determine the representative hydraulic conductivity. Further evaluation is recommended to determine the impact of pressure change on the actual hydraulic conductivity.« less

Subdivision of Glacial Deposits in Southeastern Peru Based on Pedogenic Development and Radiometric Ages

NASA Astrophysics Data System (ADS)

Goodman, Adam Y.; Rodbell, Donald T.; Seltzer, Geoffrey O.; Mark, Bryan G.

2001-07-01

The Cordillera Vilcanota and Quelccaya Ice Cap region of southern Peru (13°30‧-14°00‧S; 70°40‧-71°25‧W) contains a detailed record of late Quaternary glaciation in the tropical Andes. Quantification of soil development on 19 moraine crests and radiocarbon ages are used to reconstruct the glacial history. Secondary iron and clay increase linearly in Quelccaya soils and clay accumulates at a linear rate in Vilcanota soils, which may reflect the semicontinuous addition of eolian dust enriched in secondary iron to all soils. In contrast, logarithmic rates of iron buildup in soils in the Cordillera Vilcanota reflect chemical weathering; high concentrations of secondary iron in Vilcanota tills may mask the role of eolian input to these soils. Soil-age estimates from extrapolation of field and laboratory data suggest that the most extensive late Quaternary glaciation occurred >70,000 yr B.P. This provides one of the first semiquantitative age estimates for maximum ice extent in southern Peru and is supported by a minimum-limiting age of ∼41,520 14C yr B.P. A late glacial readvance culminated ∼16,650 cal yr B.P. in the Cordillera Vilcanota. Following rapid deglaciation of unknown extent, an advance of the Quelccaya Ice Cap occurred between ∼13,090 and 12,800 cal yr B.P., which coincides approximately with the onset of the Younger Dryas cooling in the North Atlantic region. Moraines deposited <394 cal yr B.P. in the Cordillera Vilcanota and <300 cal yr B.P. on the west side of the Quelccaya Ice Cap correlate with Little Ice Age moraines of other regions.

Examination and Manipulation of Clay Aggregates - Initial Inquiry

DTIC Science & Technology

2011-06-06

and the first conclusions in the examination and testing of clay aggregates composed of montmorillonite clay and a polysaccharide (xanthan gum, also...and the first conclusions in the examination and testing of clay aggregates composed of montmorillonite clay and a polysaccharide (xanthan gum, also...PSU and the X-gum content from 0% to 10% of the mineral content of the clay (by weight). Montmorillonite was used in all the suspensions prepared

Finite element analysis of the failure mechanism of gentle slopes in weak disturbed clays

NASA Astrophysics Data System (ADS)

Lollino, Piernicola; Mezzina, Giuseppe; Cotecchia, Federica

2014-05-01

Italian south-eastern Apennines are affected by a large number of deep slow active landslide processes that interact with urban structures and infrastructures throughout the region, thus causing damages and economic losses. For most landslide processes in the region, the main predisposing factors for instability are represented by the piezometric regime and the extremely poor mechanical properties of the weak disturbed clays in the lower and central portions of the slopes that are overlaid in some cases by a stiffer cap layer, formed of rocky flysch, e.g. alternations of rock and soil strata. Based on phenomenological approaches, landslide processes are deemed to be triggered within the weaker clay layer and later on to develop upward to the stiffer cap, with the shear bands reaching also high depths. The paper presents the results of two-dimensional numerical analyses of the failure mechanisms developing in the unstable slopes of the region, carried out by means of the finite element method (Plaxis 2011) applied to slope conditions representative for the region. In particular, the effects of slope inclination, along with the thickness and the strength of the material forming the caprock at the top of the slope, on the depth of the sliding surface, the mobilised strengths, the evolution of the landslide process and the predisposing factors of landsliding have been explored by means of the finite element analysis of an ideal case study representative of the typical geomechanical context of the region. In particular, the increase of slope inclination is shown to raise the depth of the shear band as well as to extend landslide scarp upwards, in accordance with the field evidence. Moreover, the numerical results indicate how the increase of the caprock thickness tends to confine the development of the shear band to the underlying weaker clay layer, so that the depth of the shear band is also observed to reduce, and when the stiffer top stratum becomes involved in the retrogression of the failure process. The numerical results allow also for the investigation of the variation in seepage conditions that combine with the variations in litostratigraphy in determining the variations of the features of the failure mechanism.

Effects of four different phosphorus-locking materials on sediment and water quality in Xi'an moat.

PubMed

Wang, Guanbai; Wang, Yi; Guo, Yu; Peng, Dangcong

2017-01-01

To lower phosphorus concentration in Xi'an moat, four different phosphorus-locking materials, namely, calcium nitrate, sponge-iron, fly ash, and silica alumina clay, were selected in this experiment to study their effects on water quality and sediment. Results of the continuous 68-day experiment showed that calcium nitrate was the most effective for controlling phosphorus concentration in overlying and interstitial water, where the efficiency of locking phosphorus was >97 and 90 %, respectively. Meanwhile, the addition of calcium nitrate caused Fe/Al-bound phosphorus (Fe/Al-P) content in sediment declining but Ca-bound phosphorus (Ca-P) and organic phosphorus (OP) content ascending. The phosphorus-locking efficiency of sponge-iron in overlying and interstitial water was >72 and 66 %, respectively. Meanwhile, the total phosphorus (TP), OP, Fe/Al-P, and Ca-P content in sediment increased by 33.8, 7.7, 23.1, and 23.1 %, respectively, implying that under the action of sponge-iron, the locked phosphorus in sediment was mainly inorganic form and the phosphorus-locking efficiency of sponge-iron could be stable and persistent. In addition, the phosphorus-locking efficiency of fly ash was transient and limited, let alone silica alumina clay had almost no capacity for phosphorus-locking efficiency. Therefore, calcium nitrate and sponge-iron were excellent phosphorus-locking agents to repair the seriously polluted water derived from an internal source.

Clay preference and particle transport behavior of Formosan subterranean termites (Isoptera: Rhinotermitidae): a laboratory study.

PubMed

Wang, Cai; Henderson, Gregg

2014-12-01

Although preference and utilization of clay have been studied in many higher termites, little attention has been paid to lower termites, especially subterranean termites. The Formosan subterranean termite, Coptotermes formosanus Shiraki, can modify its habitat by using clay to fill tree cavities. Here, the biological significance of clay on C. formosanus was investigated. Choice tests showed that significantly more termites aggregated in chambers where clay blocks were provided, regardless of colony group, observation period, or nutritional condition (fed or starved). No-choice tests showed that clay had no observable effect on survivorship, live or dry biomass, water content, and tunneling activity after 33-35 d. However, clay appeared to significantly decrease filter paper consumption (dry weight loss). Active particle (sand, paper, and clay) transport behavior was observed in both choice and no-choice tests. When present, clay was preferentially spread on the substrate, attached to the smooth surfaces of the containers, and used to line sand tunnels. Mechanisms and potential application of clay attraction are discussed. © 2013 Institute of Zoology, Chinese Academy of Sciences.

Integrated geophysical imaging of the Aluto-Langano geothermal field (Ethiopia).

NASA Astrophysics Data System (ADS)

Rizzello, Daniele; Armadillo, Egidio; Verdoya, Massimo; Pasqua, Claudio; Kebede, Solomon; Mengiste, Andarge; Hailegiorgis, Getenesh; Abera, Fitsum; Mengesha, Kebede; Meqbel, Naser

2017-04-01

The Aluto-Langano geothermal system is located in the central part of the Main Ethiopian Rift, one of the world's most tectonically active areas, where continental rifting has been occurring since several Ma and has yielded widespread volcanism and enhanced geothermal gradient. The geothermal system is associated to the Mt Aluto Volcanic Complex, located along the eastern margin of the rift and related to the Wonji Fault Belt, constituted by Quaternary NNE-SSW en-echelon faults. These structures are younger than the NE-SW border faults of the central Main Ethiopian Rift and were originated by a stress field oblique to the rift direction. This peculiar tectonism yielded local intense rock fracturing that may favour the development of geothermal reservoirs. In this paper, we present the results of an integrated geophysical survey carried out in 2015 over an area of about 200 km2 covering the Mt Aluto Volcanic Complex. The geophysical campaign included 162 coincident magnetotelluric and time domain electromagnetic soundings, and 207 gravity stations, partially located in the sedimentary plain surrounding the volcanic complex. Three-dimensional inversion of the full MT static-corrected tensor and geomagnetic tipper was performed in the 338-0.001 Hz band. Gravity data processing comprised digital enhancement of the residual Bouguer anomaly and 2D-3D inverse modelling. The geophysical results were compared to direct observations of stratigraphy, rock alteration and temperature available from the several deep wells drilled in the area. The magnetotelluric results imaged a low-resistivity layer which appears well correlated with the mixed alteration layer found in the wells and can be interpreted as a low-temperature clay cap. The clay-cap bottom depth is well corresponds to a change of thermal gradient. The clay cap is discontinuous, and in the central area of the volcanic complex is characterised by a dome-shape structure likely related to isotherm rising. The propilitic alteration layer, pinpointed as the 80-Ohm-m isosurface, shows two dome-shape highs. The first is NNE-trending, and may be interpreted as an upflow zone along a fault of the Wonji belt. Two productive wells are located along the borders of this area, as well as the alignements of fumaroles and altered grounds. The second is linked to a wide resistive area, located at shallow depth, where no clay cap was detected. It could be interpreted as a fossil high-temperature alteration zone reaching shallow depths, and it is associated to several fumaroles. Modeling of 2D/3D gravity data shows that the anomalies are due to shallow density variations likely related to lithology. The deep lateral variations due to structural lineaments inferred from well stratigraphy have no detectable signature. However, the trend analysis performed on the residual Bouguer anomaly (via horizontal and tilt derivative computations), allowed to identify five lineaments. Three of them exhibit NNE-SSW strike, corresponding to the Wonji Fault Belt Trend, whereas two have NNW-SSE strike, corresponding to the Red Sea Rift trend, which in this area is of minor evidence. The signature of shallow structures is then indicative of major regional structures. One of the lineaments marks the presence of a major fumarolic zone.

[Mechanism of tritium persistence in porous media like clay minerals].

PubMed

Wu, Dong-Jie; Wang, Jin-Sheng; Teng, Yan-Guo; Zhang, Ke-Ni

2011-03-01

To investigate the mechanisms of tritium persistence in clay minerals, three types of clay soils (montmorillonite, kaolinite and illite) and tritiated water were used in this study to conduct the tritium sorption tests and the other related tests. Firstly, the ingredients, metal elements and heat properties of clay minerals were studied with some instrumental analysis methods, such as ICP and TG. Secondly, with a specially designed fractionation and condensation experiment, the adsorbed water, the interlayer water and the structural water in the clay minerals separated from the tritium sorption tests were fractionated for investigating the tritium distributions in the different types of adsorptive waters. Thirdly, the location and configuration of tritium adsorbed into the structure of clay minerals were studied with infrared spectrometry (IR) tests. And finally, the forces and mechanisms for driving tritium into the clay minerals were analyzed on the basis of the isotope effect of tritium and the above tests. Following conclusions have been reached: (1) The main reason for tritium persistence in clay minerals is the entrance of tritium into the adsorbed water, the interlayer water and the structural water in clay minerals. The percentage of tritium distributed in these three types of adsorptive water are in the range of 13.65% - 38.71%, 0.32% - 5.96%, 1.28% - 4.37% of the total tritium used in the corresponding test, respectively. The percentages are different for different types of clay minerals. (2) Tritium adsorbed onto clay minerals are existed in the forms of the tritiated hydroxyl radical (OT) and the tritiated water molecule (HTO). Tritium mainly exists in tritiated water molecule for adsorbed water and interlayer water, and in tritiated hydroxyl radical for structural water. (3) The forces and effects driving tritium into the clay minerals may include molecular dispersion, electric charge sorption, isotope exchange and tritium isotope effect.

Synthesis of highly reactive subnano-sized zero-valent iron using smectite clay templates.

PubMed

Gu, Cheng; Jia, Hanzhong; Li, Hui; Teppen, Brian J; Boyd, Stephen A

2010-06-01

A novel method was developed for synthesizing subnano-sized zero-valent iron (ZVI) using smectite clay layers as templates. Exchangeable Fe(III) cations compensating the structural negative charges of smectites were reduced with NaBH(4), resulting in the formation of ZVI. The unique structure of smectite clay, in which isolated exchangeable Fe(III) cations reside near the sites of structural negative charges, inhibited the agglomeration of ZVI resulting in the formation of subnanoscale ZVI particles in the smectite interlayer regions. X-ray diffraction revealed an interlayer spacing of approximately 5 A. The non-structural iron content of this clay yields a calculated ratio of two atoms of ZVI per three cation exchange sites, in full agreement with the X-ray diffraction (XRD) results since the diameter of elemental Fe is 2.5 A. The clay-templated ZVI showed superior reactivity and efficiency compared to other previously reported forms of ZVI as indicated by the reduction of nitrobenzene; structural Fe within the aluminosilicate layers was nonreactive. At a 1:3 molar ratio of nitrobenzene/non-structural Fe, a reaction efficiency of 83% was achieved, and over 80% of the nitrobenzene was reduced within one minute. These results confirm that non-structural Fe from Fe(III)-smectite was reduced predominantly to ZVI which was responsible for the reduction of nitrobenzene to aniline. This new form of subnanoscale ZVI may find utility in the development of remediation technologies for persistent environmental contaminants, for example, as components of constructed reactive domains such as reactive caps for contaminated sediments.

Synthesis of Highly Reactive Subnano-sized Zero-valent Iron using Smectite Clay Templates

PubMed Central

Gu, Cheng; Jia, Hanzhang; Li, Hui; Teppen, Brian J.; Boyd, Stephen A.

2010-01-01

A novel method was developed for synthesizing subnano-sized zero-valent iron (ZVI) using smectite clay layers as templates. Exchangeable Fe(III) cations compensating the structural negative charges of smectites were reduced with NaBH4, resulting in the formation of ZVI. The unique structure of smectite clay, in which isolated exchangeable Fe(III) cations reside near the sites of structural negative charges, inhibited the agglomeration of ZVI resulting in the formation of discrete regions of subnanoscale ZVI particles in the smectite interlayer regions. X-ray diffraction revealed an interlayer spacing of ~ 5 Å. The non-structural iron content of this clay yields a calculated ratio of two atoms of ZVI per three cation exchange sites, in full agreement with the XRD results since the diameter of elemental Fe is 2.5 Å. The clay-templated ZVI showed superior reactivity and efficiency compared to other previously reported forms of ZVI as indicated by the reduction of nitrobenzene; structural Fe within the aluminosilicate layers was nonreactive. At a 1:3 molar ratio of nitrobenzene:non-structural Fe, a reaction efficiency of 83% was achieved, and over 80% of the nitrobenzene was reduced within one minute. These results confirm that non-structural Fe from Fe(III)-smectite was reduced predominantly to ZVI which was responsible for the reduction of nitrobenzene to aniline. This new form of subnano-scale ZVI may find utility in the development of remediation technologies for persistent environmental contaminants, e.g. as components of constructed reactive domains such as reactive caps for contaminated sediments. PMID:20446730

Installation Restoration Program. Phase 2. Confirmation/Quantification Stage 2, Moody Air Force Base, Georgia. Appendices. Volume 1

DTIC Science & Technology

1988-11-01

Light gray NB, clayey (kaolin). Poetv al - quartz mad to fine sand, mod. (0 Locking Cap plastic , saturated. 3 COMPILED BY B. Painter (EWM) t DATE 11-21...Painter (EUM) -SAMPLE PNTAINSOIL DESCRIIPTION COMMENTS ZTEST NAME. GRADATION OR PLASTICITY ,. DEPTH Of CASING, W ~ 1NPARTICLE SIZE DISTRIBUTION. COLOR...L. Grayish orange 10 YR 7/4. quart. RNDEVAI: very tine Sandy clay, dense, DIAMETER: 2-inrh Srhe So PVC moderately plastics dry. DEPTH: 2 - fenot[ 1

Geological and geophysical properties of cap rock in a natural CO2 occurrence, Mihályi-Répcelak area, Western Hungary

NASA Astrophysics Data System (ADS)

Király, Csilla; Szamosfalvi, Ágnes; Sendula, Eszter; Páles, Mariann; Kovács, István; Kónya, Péter; Falus, György; Szabó, Csaba

2015-04-01

The physical and geochemical consistency of the cap rock is primarily important for safe geological storage of CO2.. As a consequence of CO2 injection reactions took place between the minerals of the reservoir, the cap rock and CO2 saturated pore water. These reactions may change the mineral composition and petrophysical properties of the storage reservoir as well as the cap rock that provides the only physical barrier that retains carbon dioxide in the target reservoir formation. Study of the natural CO2 occurrences delivers information to understand which properties of a cap rock provide the sustainable closure and retainment. Knowledge of the long term effect of CO2 on the behavior of the cap rock is an important input in the selection procedure of a potential CO2 injection site. Yet, very few data exist on geochemical properties and reactivity of the cap rocks. During normal commercial operations the reservoir is typically cored, but not the cap rock. This study may enhance our knowledge about possible mineralogical reactions, which can occur in clayey-aleuritic cap rocks. The Mihályi-Répcelak natural CO2 occurrence is believed to be leakage safe. There is no known seepage on the surface. It is suggested that the aleuritic clay rich cap rock occurring at the natural reservoir can stop CO2 migration into other reservoirs or to the surface. The most important characteristics of cap rocks that they have low permeability (<0.1 mD) and porosity (eff.por. = 4%) and high clayeyness (approx. 80%). However, we demonstrate that in addition to these parameters the geochemical properties of cap rock is also important. In order to characterize the natural CO2 occurrence, we applied the following analysis, like XRD, FTIR, SEM. The petrophysical properties are determined from the interpretation of geophysical well-logs and grain size distribution. The most important result of this study that adequate petrophysical properties do not completely define the suitability of a cap rock. The effective porosity (~4 %), permeability (0.026 mD) and clayeyness (~80%) data imply that the studied aleurolites are good cap rocks. The mineral composition of cap rock is similar to that of reservoir rock, however, the ratio of components is different. The mineralogical analysis and petrography yield to the reaction between CO2 and the cap rocks. The most visible effect of CO2 presence is the dawsonite precipitation after albite dissolution within the cap rocks. Therefore, the CO2 may migrate through the cap rocks in geological time scale, however the total system could be leakage safe.

40 CFR 1060.521 - How do I test fuel caps for permeation emissions?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false How do I test fuel caps for permeation... EQUIPMENT Test Procedures § 1060.521 How do I test fuel caps for permeation emissions? If you measure a fuel.... However, you may not combine these emission measurements if you test the fuel cap at a nominal temperature...

40 CFR 1060.521 - How do I test fuel caps for permeation emissions?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false How do I test fuel caps for permeation... EQUIPMENT Test Procedures § 1060.521 How do I test fuel caps for permeation emissions? If you measure a fuel.... However, you may not combine these emission measurements if you test the fuel cap at a nominal temperature...

40 CFR 1060.521 - How do I test fuel caps for permeation emissions?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false How do I test fuel caps for permeation... EQUIPMENT Test Procedures § 1060.521 How do I test fuel caps for permeation emissions? If you measure a fuel.... However, you may not combine these emission measurements if you test the fuel cap at a nominal temperature...

40 CFR 1060.521 - How do I test fuel caps for permeation emissions?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false How do I test fuel caps for permeation... EQUIPMENT Test Procedures § 1060.521 How do I test fuel caps for permeation emissions? If you measure a fuel.... However, you may not combine these emission measurements if you test the fuel cap at a nominal temperature...

[Removal efficiency of red tide organisms by modified clay and its impacts on cultured organisms].

PubMed

Cao, Xi-hua; Song, Xiu-xian; Yu, Zhi-ming

2004-09-01

Removal efficiencies of Prorocentrum donghaiense (Prorocentrum dentatum) by Hexadecyltrimethylammonium (HDTMA) bromide and organo-clay modified by HDTMA were identified. Moreover the toxicity of the unbound HDTMA and HDTMA plus clay to aquacultural organisms, Penaeus japonicus, was also tested. The results suggested that (1) The unbound HDTMA had an excellent ability to remove the red tide organisms. However, its strong toxicity to Penaeus japonicus would restrict its practical use in red tide control. (2) The toxicity of HDTMA could be remarkably decreased by addition of clay and the organo-clay complex had a good ability to removal red tide organisms. At the same time the availability of organo-clay to remove the red tide of P. donghaiense and Heterosigma akashiwo in the lab-imitated cultures were studied. The results indicated that the organo-clay complex could remove 100% P. donghaiense at the dosage of 0.03 g/L and effectively control H. akashiwo at 0.09 g/L while the survival rate of Penaeus japonicus larvae, which were cultured in the red tide seawater, is kept 100%. According to the results in laboratory, the mesocosm tests (CEPEX) in East China Sea were conducted in April and May of 2003. The removal efficiencies of original clay, organic clay and inorganic clay were compared during the CEPEX tests. The results revealed that both inorganic clay and organic clay could remove red tide organisms more effectively than the original clay.

Feasibility of Plasma Treated Clay in Clay/Polymer Nanocomposites Powders for use Laser Sintering (LS)

NASA Astrophysics Data System (ADS)

Almansoori, Alaa; Seabright, Ryan; Majewski, C.; Rodenburg, C.

2017-05-01

The addition of small quantities of nano-clay to nylon is known to improve mechanical properties of the resulting nano-composite. However, achieving a uniform dispersion and distribution of the clay within the base polymer can prove difficult. A demonstration of the fabrication and characterization of plasma-treated organoclay/Nylon12 nanocomposite was carried out with the aim of achieving better dispersion of clay platelets on the Nylon12 particle surface. Air-plasma etching was used to enhance the compatibility between clays and polymers to ensure a uniform clay dispersion in composite powders. Downward heat sintering (DHS) in a hot press is used to process neat and composite powders into tensile and XRD specimens. Morphological studies using Low Voltage Scanning Electron Microscopy (LV-SEM) were undertaken to characterize the fracture surfaces and clay dispersion in powders and final composite specimens. Thermogravimetric analysis (TGA) testing performed that the etched clay (EC) is more stable than the nonetched clay (NEC), even at higher temperatures. The influence of the clay ratio and the clay plasma treatment process on the mechanical properties of the nanocomposites was studied by tensile testing. The composite fabricated from (3% EC/N12) powder showed ~19 % improvement in elastic modulus while the composite made from (3% NEC/N12) powder was improved by only 14%). Most notably however is that the variation between tests is strongly reduced when etch clay is used in the composite. We attribute this to a more uniform distribution and better dispersion of the plasma treated clay within polymer powders and ultimately the composite.

Impact of Exposure to Pressure of 50 MPa on the Specific Surface Area of Clay

NASA Astrophysics Data System (ADS)

Koszela-Marek, Ewa

2017-12-01

The paper presents results of laboratory tests conducted to determine the impact of pressure of 50 MPa on specific surface area of clay. These tests were carried out in an original, high-pressure test stand. The specific surface area of clay extracted directly from an open pit mine was compared with the specific surface area of the same clay subjected to the pressure of 50 MPa in a high-pressure chamber. The study found that the specific surface area of the clay subjected to the pressure of 50 MPa increased distinctly by over 35 %. The increase in specific surface can be a result of changes in the microstructure of clay particles and microstructural alteration in the soil skeleton, caused by the pressure.

Chronology for the Cueva Victoria fossil site (SE Spain): Evidence for Early Pleistocene Afro-Iberian dispersals.

PubMed

Gibert, Luis; Scott, Gary R; Scholz, Denis; Budsky, Alexander; Ferràndez, Carles; Ribot, Francesc; Martin, Robert A; Lería, María

2016-01-01

Cueva Victoria has provided remains of more than 90 species of fossil vertebrates, including a hominin phalanx, and the only specimens of the African cercopithecid Theropithecus oswaldi in Europe. To constrain the age of the vertebrate remains we used paleomagnetism, vertebrate biostratigraphy and (230)Th/U dating. Normal polarity was identified in the non-fossiliferous lowest and highest stratigraphic units (red clay and capping flowstones) while reverse polarity was found in the intermediate stratigraphic unit (fossiliferous breccia). A lower polarity change occurred during the deposition of the decalcification clay, when the cave was closed and karstification was active. A second polarity change occurred during the capping flowstone formation, when the upper galleries were filled with breccia. The mammal association indicates a post-Jaramillo age, which allows us to correlate this upper reversal with the Brunhes-Matuyama boundary (0.78 Ma). Consequently, the lower reversal (N-R) is interpreted as the end of the Jaramillo magnetochron (0.99 Ma). These ages bracket the age of the fossiliferous breccia between 0.99 and 0.78 Ma, suggesting that the capping flowstone was formed during the wet Marine Isotopic Stage 19, which includes the Brunhes-Matuyama boundary. Fossil remains of Theropithecus have been only found in situ ∼1 m below the B/M boundary, which allows us to place the arrival of Theropithecus to Cueva Victoria at ∼0.9-0.85 Ma. The fauna of Cueva Victoria lived during a period of important climatic change, known as the Early-Middle Pleistocene Climatic Transition. The occurrence of the oldest European Acheulean tools at the contemporaneous nearby site of Cueva Negra suggest an African dispersal into SE Iberia through the Strait of Gibraltar during MIS 22, when sea-level was ∼100 m below its present position, allowing the passage into Europe of, at least, Theropithecus and Homo bearing Acheulean technology. Copyright © 2015 Elsevier Ltd. All rights reserved.

Magnetic and GPR surveys of a former munitions foundry site at the Denver Federal Center

USGS Publications Warehouse

Campbell, David L.; Beanland, Shay; Lucius, Jeffrey E.; Powers, Michael H.

2000-01-01

We made magnetometer and ground penetrating radar (GPR) surveys over part of the foundation of a World War II-era foundry located on the Denver Federal Center. The site contains a number of highly magnetic source bodies, concrete foundation walls, and underground openings, buried under a clay cap. The cap is several feet thick and has a conductivity of about 35 mS/m, making the features underneath it a poor target for conventional GPR. Indeed, the raw data look unlike typical GPR data, but rather show reverberation (?) bands under sidewalks and other shallow buried sources. Using a newly-written computer package, we made plan maps of the GPR response at different time slices. The sliced GPR data did not outline buried foundry foundations, as we had hoped it might. The resulting plan maps of the sliced data show sidewalks and other blobby features, some of which correspond to magnetometer highs.

Modeling of subsurface structures in Telomoyo Volcano geothermal area, Magelang using 1-D magnetotelluric method

NASA Astrophysics Data System (ADS)

Sarjan, Achmad Fajar Narotama; Niasari, Sintia Windhi

2017-07-01

There are some of geothermal prospects around Java Island. One of them are located in Telomoyo Volcano area, Magelang, Central Java. The existence of hot spring manifestations in Telomoyo Volcano area shows the presence of geothermal system. The upflow zone of this geothermal system was formed in the caldera of Telomoyo Volcano area, while the outflow zone was formed around Candi Umbul. In addition, from the geological map shows a geological structure assumed as a normal fault with southwest-northeast orientation that was caused by the volcanic activity. The aim of this research is to give a brief introduction about subsurface resistivity beneath Telomoyo Volcano area using 1-D magnetotelluric forward model. Thus, we can determine the possibility of data that will obtained during the acquisition process based on the geological model that was made. The apparent resistivity, phase, and period values were obtained from the forward modeling process. The result from this study is a 1-D resistivity section with synthetics curves of each geothermal model. In each model the presence of clay cap characterized by a low resistivity layer. A layer below the clay cap with a medium resistivity value interpreted as the reservoir of this geothermal system. The heat source of this geothermal area is characterized by a low resistivity that is located at depth 4000-5500m. This study is still in progress to acquire the exact values of resistivity from each layer from the field data acquisition in Telomoyo Volcano area, Magelang.

Vesicular delivery of crystalline calcium minerals to ECM in biomineralized nanoclay composites

NASA Astrophysics Data System (ADS)

Katti, Kalpana S.; Ambre, Avinash H.; Payne, Scott; Katti, Dinesh R.

2015-04-01

The mechanisms of mineralization and new bone formation were explored in newly formed extracellular matrix in a nanoclay based composite. Nanoclay films were prepared by intercalating the clays with amino acids and using the amino acids for mineralization of hydroxyapatite. The biomineralized hydroxyapatite (HAP) inside nanoclay galleries or in situ HAP/clay was further used to make films (substrates) using polycaprolactone (PCL) that were seeded with mesenchymal stem cells in a two-stage seeding process. SEM imaging experiments performed on PCL/in situ HAPclay composite films seeded with human MSCs indicated formation of matrix vesicles. The vesicles appear to emerge from the cells that are adhered to the nanoclay HAP films and also deposited in the extracellular space. Vesicles are also observed to be embedded in the cells or under the surface of cells. Crystalline structures with Ca and P were found inside vesicles. The Ca/P ratios obtained using energy dispersive spectroscopy indicate values ranging from below 0.7 to the stoichiometric HAP value of 1.67. The Ca/P ratios were obtained to be closer to the stoichiometric value for single seeding experiments as compared to the double seeding experiments indicating more new bone formation in double seeding experiments. New bone formation with bone mimetic mineralization is thus observed on the in situ HAP nanoclay PCL samples. Hence the PCL/in situ HAPclay composites besides being osteoinductive are also capable of providing a favorable micro-environment for cell dependent processes involved in bone mineral formation.

Colorstratigraphy; A New Stratigraphic Correlation Technique

NASA Astrophysics Data System (ADS)

Nanayakkara, N. U.; Ranasinghage, P. N.; Priyantha, C.; Abillapitiya, T.

2016-12-01

Here we introduce a novel stratigraphic technique namely colorstratigraphy for correlating sedimentary sequences. Minihagalkanda is about 1 km long amphitheater like sedimentary terrain, situated at the southeastern coast of Sri Lanka. It has Miocene sedimentary sequences, separated in to 10-12 m high small hillocks by erosion, and bounded by about 30 m high escarpment. Sandstone, yellowish sandy clay, greenish silty clay sequences are capped by 4-5 m limestone bed in these hillocks but not at the boundary escarpment. Stratigraphic profiles at two hillocks and the boundary escarpment, separated each other by 200-300 m, were selected to test the new colorstartigraphic correlation technique. Color reflectance (DSR) was measured at four samples in each sequence at every profile and hence altogether 36 reflectance measurements were taken using Minolta 2500D hand-held color spectrophotometer. The first-derivative of the reflectance spectra (dR/dλ) defines the "spectral shape" of the sample. Therefore, DSR data (360-740 nm) measured at 10 nm resolution were used to calculate a center-weighted, first-derivative spectra for each reflectance sample consisting of 39 channels. Particle size of each sequence was measured at all 03 profiles using laser particle size analyzer to verify the stratigraphic correlation. Mean reflectance spectrum for each sequence at all 03 profiles were plotted on the same graph for comparison. Same was done for the grain size spectrums. Discriminant function analysis was performed separately for dsr data and grain size data using a number assigned to each sedimentary sequence as the grouping variable Color spectrums of sandstone, yellowish sandy clay, and greenish silty clay sequences at all three profiles perfectly match showing clear stratigraphic correlation among these three stratigraphic profiles. Matching grain size distribution curves of the three sequence at the three profiles verify the stratigraphic correlation. Perfect 100 % discrimination of the three sequences with color reflectance data proves the accuracy of the correlation. Similar 100 % discrimination resulted with grain size data further verifies the results. Therefore, colorstratigraphy based on DSR can be introduced as a quick and easy technique for stratigraphic correlation of sedimentary sequences.

Geologic controls on gas hydrate occurrence in the Mount Elbert prospect, Alaska North Slope

USGS Publications Warehouse

Boswell, R.; Rose, K.; Collett, T.S.; Lee, M.; Winters, W.; Lewis, K.A.; Agena, W.

2011-01-01

Data acquired at the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well, drilled in the Milne Point area of the Alaska North Slope in February, 2007, indicates two zones of high gas hydrate saturation within the Eocene Sagavanirktok Formation. Gas hydrate is observed in two separate sand reservoirs (the D and C units), in the stratigraphically highest portions of those sands, and is not detected in non-sand lithologies. In the younger D unit, gas hydrate appears to fill much of the available reservoir space at the top of the unit. The degree of vertical fill with the D unit is closely related to the unit reservoir quality. A thick, low-permeability clay-dominated unit serves as an upper seal, whereas a subtle transition to more clay-rich, and interbedded sand, silt, and clay units is associated with the base of gas hydrate occurrence. In the underlying C unit, the reservoir is similarly capped by a clay-dominated section, with gas hydrate filling the relatively lower-quality sands at the top of the unit leaving an underlying thick section of high-reservoir quality sands devoid of gas hydrate. Evaluation of well log, core, and seismic data indicate that the gas hydrate occurs within complex combination stratigraphic/structural traps. Structural trapping is provided by a four-way fold closure augmented by a large western bounding fault. Lithologic variation is also a likely strong control on lateral extent of the reservoirs, particularly in the D unit accumulation, where gas hydrate appears to extend beyond the limits of the structural closure. Porous and permeable zones within the C unit sand are only partially charged due most likely to limited structural trapping in the reservoir lithofacies during the period of primary charging. The occurrence of the gas hydrate within the sands in the upper portions of both the C and D units and along the crest of the fold is consistent with an interpretation that these deposits are converted free gas accumulations formed prior to the imposition of gas hydrate stability conditions. ?? 2009.

40 CFR 1060.521 - How do I test fuel caps for permeation emissions?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I test fuel caps for permeation... EQUIPMENT Test Procedures § 1060.521 How do I test fuel caps for permeation emissions? If you measure a fuel tank's permeation emissions with a nonpermeable covering in place of the fuel cap under § 1060.520(b)(5...

Application of viscoelastic, viscoplastic, and rate-and-state friction constitutive laws to the deformation of unconsolidated sands

NASA Astrophysics Data System (ADS)

Hagin, Paul N.

Laboratory experiments on dry, unconsolidated sands from the Wilmington field, CA, reveal significant viscous creep strain under a variety of loading conditions. In hydrostatic compression tests between 10 and 50 MPa of pressure, the creep strain exceeds the magnitude of the instantaneous strain and follows a power law function of time. Interestingly, the viscous effects only appear when loading a sample beyond its preconsolidation pressure. Cyclic loading tests (at quasi-static frequencies of 10-6 to 10 -2 Hz) show that the bulk modulus increases by a factor of two with increasing frequency while attenuation remains constant. I attempt to fit these observations using three classes of models: linear viscoelastic, viscoplastic, and rate-and-state friction models. For the linear viscoelastic modeling, I investigated two types of models; spring-dashpot (exponential) and power law models. I find that a combined power law-Maxwell solid creep model adequately fits all of the data. Extrapolating the power law-Maxwell creep model out to 30 years (to simulate the lifetime of a reservoir) predicts that the static bulk modulus is 25% of the dynamic modulus, in good agreement with field observations. Laboratory studies also reveal that a large portion of the deformation is permanent, suggesting that an elastic-plastic model is appropriate. However, because the viscous component of deformation is significant, an elastic-viscoplastic model is necessary. An appropriate model for unconsolidated sands is developed by incorporating Perzyna (power law) viscoplasticity theory into the modified Cambridge clay cap model. Hydrostatic compression tests conducted as a function of volumetric strain rate produced values for the required model parameters. As a result, by using an end cap model combined with power law viscoplasticity theory, changes in porosity in both the elastic and viscoplastic regimes can be predicted as a function of both stress path and strain rate. To test whether rate-and-state friction laws can be used to model creep strain, I expand the rate-and-state formulation to include deformation under hydrostatic stress boundary conditions. Results show that the expanded rate-and-state formulation successfully describes the creep strain of unconsolidated sand. Finally, I show that the viscoplastic end cap and rate-and-state models are mathematically similar.

NASA Tech Briefs, December 2003

NASA Technical Reports Server (NTRS)

2003-01-01

Topics covered include: Organic/Inorganic Hybrid Polymer/Clay Nanocomposites; Less-Toxic Coatings for Inhibiting Corrosion of Aluminum; Liquid Coatings for Reducing Corrosion of Steel in Concrete; Processable Polyimides Containing APB and Reactive End Caps; Rod/Coil Block Copolyimides for Ion-Conducting Membranes; Techniques for Characterizing Microwave Printed Antennas; Cylindrical Antenna With Partly Adaptive Phased-Array Feed; Command Interface ASIC - Analog Interface ASIC Chip Set; Predicting Accumulations of Ice on Aerodynamic Surfaces; Analyzing Aeroelasticity in Turbomachines; Software for Allocating Resources in the Deep Space Network; Expert Seeker; High-Speed Recording of Test Data on Hard Disks; Functionally Graded Nanophase Beryllium/Carbon Composites; Thin Thermal-Insulation Blankets for Very High Temperatures; Aerostructures Test Wing; Flight-Test Evaluation of Flutter-Prediction Methods; Piezoelectrically Actuated Microvalve for Liquid Effluents; Larger-Stroke Piezoelectrically Actuated Microvalve; Innovative, High-Pressure, Cryogenic Control Valve: Short Face-to-Face, Reduced Cost; Safer Roadside Crash Walls Would Limit Deceleration; Improved Interactive Medical-Imaging System; Scanning Microscopes Using X Rays and Microchannels; Slotting Fins of Heat Exchangers to Provide Thermal Breaks; Methane Clathrate Hydrate Prospecting; Automated Monitoring with a BSP Fault-Detection Test; Automated Monitoring with a BCP Fault-Decision Test; Vector-Ordering Filter Procedure for Data Reduction; Remote Sensing and Information Technology for Large Farms; Developments at the Advanced Design Technologies Testbed; Spore-Forming Bacteria that Resist Sterilization; and Acoustical Applications of the HHT Method.

A laboratory study of supercritical CO2 adsorption on cap rocks in the geological storage conditions

NASA Astrophysics Data System (ADS)

Jedli, Hedi; Jbara, Abdessalem; Hedfi, Hachem; Bouzgarrou, Souhail; Slimi, Khalifa

2017-04-01

In the present study, various cap rocks have been experimentally reacted in water with supercritical CO2 in geological storage conditions ( P = 8 × 106 Pa and T = 80 °C) for 25 days. To characterize the potential CO2-water-rock interactions, an experimental setup has been built to provide additional information concerning the effects of structure, thermal and surface characteristics changes due to CO2 injection with cap rocks. In addition, CO2 adsorption capacities of different materials (i.e., clay evaporate and sandstone) are measured. These samples were characterized by XRD technique. The BET specific surface area was determined by nitrogen isotherms. In addition, thermal characteristics of untreated adsorbents were analyzed via TGA method and topography surfaces are identified by Scanning Electron Microscope (SEM). Taking into account pressure and temperature, the physical as well as chemical mechanisms of CO2 retention were determined. Isotherm change profiles of samples for relative pressure range indicate clearly that CO2 was adsorbed in different quantities. In accordance with the X-ray diffraction, a crystalline phase was formed due to the carbonic acid attack and precipitation of some carbonate.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malin, Peter E.; Shalev, Eylon; Onacha, Stepthen A.

In this final report, we discuss both theoretical and applied research resulting from our DOE project, ICEKAP 2004: A Collaborative Joint Geophysical Imaging Project at Krafla and IDDP. The abstract below begins with a general discussion of the problem we addressed: the location and characterization of “blind” geothermal resources using microearthquake and magnetotelluric measurements. The abstract then describes the scientific results and their application to the Krafla geothermal area in Iceland. The text following this abstract presents the full discussion of this work, in the form of the PhD thesis of Stephen A. Onacha. The work presented here was awardedmore » the “Best Geophysics Paper” at the 2005 Geothermal Resources Council meeting, Reno. This study presents the modeling of buried fault zones using microearthquake and electrical resistivity data based on the assumptions that fluid-filled fractures cause electrical and seismic anisotropy and polarization. In this study, joint imaging of electrical and seismic data is used to characterize the fracture porosity of the fracture zones. P-wave velocity models are generated from resistivity data and used in locating microearthquakes. Fracture porosity controls fluid circulation in the hydrothermal systems and the intersections of fracture zones close to the heat source form important upwelling zones for hydrothermal fluids. High fracture porosity sites occur along fault terminations, fault-intersection areas and fault traces. Hydrothermal fault zone imaging using resistivity and microearthquake data combines high-resolution multi-station seismic and electromagnetic data to locate rock fractures and the likely presence fluids in high temperature hydrothermal systems. The depths and locations of structural features and fracture porosity common in both the MT and MEQ data is incorporated into a joint imaging scheme to constrain resistivity, seismic velocities, and locations of fracture systems. The imaging of the fault zones is constrained by geological, drilling, and geothermal production data. The objective is to determine interpretation techniques for evaluating structural controls of fluid circulation in hydrothermal systems. The conclusions are: • directions of MT polarization and anisotropy and MEQ S-splitting correlate. Polarization and anisotropy are caused by fluid filled fractures at the base of the clay cap. •Microearthquakes occur mainly on the boundary of low resistivity within the fracture zone and high resistivity in the host rock. Resistivity is lowest within the core of the fracture zone and increases towards the margins of the fracture zone. The heat source and the clay cap for the hydrothermal have very low resistivity of less than 5Ωm. •Fracture porosity imaged by resistivity indicates that it varies between 45-5% with most between 10-20%, comparable to values from core samples in volcanic areas in Kenya and Iceland. For resistivity values above 60Ωm, the porosity reduces drastically and therefore this might be used as the upper limit for modeling fracture porosity from resistivity. When resistivity is lower than 5Ωm, the modeled fracture porosity increases drastically indicating that this is the low resistivity limit. This is because at very low resistivity in the heat source and the clay cap, the resistivity is dominated by ionic conduction rather than fracture porosity. •Microearthquakes occur mainly above the heat source which is defined by low resistivity at a depth of 3-4.5 km at the Krafla hydrothermal system and 4-7 km in the Longonot hydrothermal system. •Conversions of S to P waves occur for microearthquakes located above the heat source within the hydrothermal system. Shallow microearthquakes occur mainly in areas that show both MT and S-wave anisotropy. •S-wave splitting and MT anisotropy occurs at the base of the clay cap and therefore reflects the variations in fracture porosity on top of the hydrothermal system. •In the Krafla hydrothermal system in Iceland, both MT polarization and MEQ splitting directions align with zones that have high fracture porosity below the clay cap. These zones coincide with fault zones trending in the NNE-SSW and NW-SE directions in otherwise uniform volcanic rocks and laterally continuous geology. The NW-SE orientation is parallel to the regional shear fractures while the NNE-SSW trending polarizations align parallel to rift zone fracture swarms. This suggest that correlations between MT polarizations and MEQ splitting may be related to fluid filled fractures. •In areas of high resistivity (60Ωm), the P-wave velocity approaches that of the rock matrix. •S-wave splitting polarization is determined from measurements of angles of rotation to get the optimum direction of polarization. •The use of MEQ and resistivity for imaging fractures requires that the MEQ data acquisition system be located close to the fracture zone.« less

Synthesis of organic/inorganic hybrid gel with acid activated clay after γ-ray radiation.

PubMed

Kim, Donghyun; Lee, Hoik; Sohn, Daewon

2014-08-01

A hybrid gel was prepared from acid activated clay (AA clay) and acrylic acid by gamma ray irradiation. Irradiated inorganic particles which have peroxide groups act as initiator because it generates oxide radicals by increasing temperature. Inorganic nanoparticles which are rigid part in hybrid gel also contribute to increase the mechanical property as a crosslinker. We prepared two hybrid gels to compare the effect of acid activated treatment of clay; one is synthesized with raw clay particles and another is synthesized with AA clay particles. The composition and structure of AA clay particles and raw clay particles were confirmed by X-ray diffraction (XRD), X-ray fluorescence instrument and surface area analyzer. And chemical and physical property of hybrid gel with different ratios of acrylic acid and clay particle was tested by Raman spectroscope and universal testing machine (UTM). The synthesized hydrogel with 76% gel contents can elongated approximately 1000% of its original size.

Hydraulic and mechanical behavior of landfill clay liner containing SSA in contact with leachate.

PubMed

Zhang, Qian; Lu, Haijun; Liu, Junzhu; Wang, Weiwei; Zhang, Xiong

2018-05-01

Sewage sludge ash (SSA) produced by municipal sludge can be used as a modified additive for clay liner, and improves the working performance of landfill clay liner in contact with leachate. Under the action of landfill leachate, the permeability, shear strength, phase composition, and pore structure of the modified clay are investigated through the flexible wall permeability test, triaxial shear test, thermal gravimetric and differential thermal analysis, and low-temperature nitrogen adsorption test, respectively. The hydraulic conductivity of the modified clay containing 0-5% SSA is in the range of 3.94 × 10 -8 -1.16 × 10 -7  cm/s, and the pollutant concentration of the sample without SSA was higher than others. The shear strength of the modified clay is more than that of the traditional clay liner, the cohesion rate of modified clay increases from 32.5 to 199.91 kPa, and the internal friction angle decreases from 32.5° to 15.6°. Furthermore, the weight loss rates of the samples are 15.69%, 17.92%, 18.06%, and 20.68%, respectively, when the SSA content increases from 0% to 5%. The total pore volume and average pore diameter of the modified clay decrease with the increase in the SSA content, respectively. However, the specific area of the modified clay increases with the increase in the SSA content.

Application of artificial neural network to predict clay sensitivity in a high landslide prone area using CPTu data- A case study in Southwest of Sweden

NASA Astrophysics Data System (ADS)

Shahri, Abbas; Mousavinaseri, Mahsasadat; Naderi, Shima; Espersson, Maria

2015-04-01

Application of Artificial Neural Networks (ANNs) in many areas of engineering, in particular to geotechnical engineering problems such as site characterization has demonstrated some degree of success. The present paper aims to evaluate the feasibility of several various types of ANN models to predict the clay sensitivity of soft clays form piezocone penetration test data (CPTu). To get the aim, a research database of CPTu data of 70 test points around the Göta River near the Lilli Edet in the southwest of Sweden which is a high prone land slide area were collected and considered as input for ANNs. For training algorithms the quick propagation, conjugate gradient descent, quasi-Newton, limited memory quasi-Newton and Levenberg-Marquardt were developed tested and trained using the CPTu data to provide a comparison between the results of field investigation and ANN models to estimate the clay sensitivity. The reason of using the clay sensitivity parameter in this study is due to its relation to landslides in Sweden.A special high sensitive clay namely quick clay is considered as the main responsible for experienced landslides in Sweden which has high sensitivity and prone to slide. The training and testing program was started with 3-2-1 ANN architecture structure. By testing and trying several various architecture structures and changing the hidden layer in order to have a higher output resolution the 3-4-4-3-1 architecture structure for ANN in this study was confirmed. The tested algorithm showed that increasing the hidden layers up to 4 layers in ANN can improve the results and the 3-4-4-3-1 architecture structure ANNs for prediction of clay sensitivity represent reliable and reasonable response. The obtained results showed that the conjugate gradient descent algorithm with R2=0.897 has the best performance among the tested algorithms. Keywords: clay sensitivity, landslide, Artificial Neural Network

Four Types of Deposits From Wet Conditions on Early Mars

NASA Technical Reports Server (NTRS)

2008-01-01

Each of these four panels shows a close-up view of a different type of geological deposit formed with the involvement of water, based on observations by NASA's Mars Reconnaissance Orbiter. All four date from the earliest period of Martian history, called the Noachian Period.

The upper-left panel shows carbonates overlying clays in the Nili Fossae region of Mars. The view combines color-coded information from infrared spectral observations by the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) with an underlying black-and-white image from the High Resolution Imaging Science Experiment (HiRISE) camera. Beneath a rough-textured capping rock unit (purple) lie banded olivine-bearing layers (yellow), which in some places have been partially or wholly altered to carbonate (green).

The upper-right panel shows phyllosilicates and chlorides in the Terra Sirenum region, observed by CRISM and HiRISE. Medium-toned, finely fractured rocks containing chloride salts either underlie higher-standing, light-toned phyllosilicates or fill in low spots between them. Both sit on dark, eroded volcanic material.

The lower-left panel shows the upper portion of canyon wall in Coprates Chasma, observed by HiRISE and CRISM. The chasm rim cuts across the middle of the image. The wall slopes down to the top of the image and continues outside the region shown, exposing multiple phyllosilicate-bearing layers in a section of rock 7 kilometers (4 miles) thick. Two of the layers shown here are finely fractured aluminum clays that dominate the lower half of the image, underlain by thin beds of iron-magnesium clays at the top of the image. The dark material is a remnant of an overlying layer of basaltic sand that has been partly eroded away by the wind.

The lower-right panel shows phyllosilicates with vertically layered compositions in Mawrth Vallis, observed by HiRISE (presented in enhanced color) and CRISM. The brown-colored knob in the middle of the scene is a remnant of cap rock that overlies aluminum clays (blue-gray), which in turn overlie iron-magnesium clays (buff).

NASA's Jet Propulsion Laboratory, a division of the California Institute of Technology, Pasadena, manages the Mars Reconnaissance Orbiter for the NASA Science Mission Directorate, Washington. Lockheed Martin Space Systems, Denver, is the prime contractor for the project and built the spacecraft. The Johns Hopkins University Applied Physics Laboratory led the effort to build the CRISM instrument and operates CRISM in coordination with an international team of researchers from universities, government and the private sector. The University of Arizona, Tucson, operates the HiRISE camera, which was built by Ball Aerospace & Technologies Corp., Boulder, Colo.

The Archaeology of Coralville Lake, Iowa. Volume 3. Sample Survey (Interim Report 1).

DTIC Science & Technology

1985-03-01

n t ho I aite 19 60 ’ s , Air ian Anderson di rectedl a se-r ies coI Li in a ner e I cd s c1. ooIs v It 1h s tude ntLs f r om the tini v-er’si ty of r...wash cap the surface (Figure 13). 7 0- ii NORTH PROFILE 13 JH 479- UNIT 2 SIL WY 3/ c(HISTOWiCAL ALLUVIUM) stl ~SILT WVITH MINk CLAY JOYN 3/3 SCALE I

Value of Information spreadsheet

DOE Data Explorer

Trainor-Guitton, Whitney

2014-05-12

This spreadsheet represents the information posteriors derived from synthetic data of magnetotellurics (MT). These were used to calculate value of information of MT for geothermal exploration. Information posteriors describe how well MT was able to locate the "throat" of clay caps, which are indicative of hidden geothermal resources. This data is full explained in the peer-reviewed publication: Trainor-Guitton, W., Hoversten, G. M., Ramirez, A., Roberts, J., Júlíusson, E., Key, K., Mellors, R. (Sept-Oct. 2014) The value of spatial information for determining well placement: a geothermal example, Geophysics.

[A novel diagnostic method for allergy "LUCICA HRT"].

PubMed

Yamakoshi, M; Fujii, Y; Nagai, H; Ohyama, K

1997-02-01

We developed a novel glass microfiber-based histamine release test (HRT) which is characteristic of response of basophil leukocyte to allergens in vitro. It allows the determination of 20 allergens (10 for inhalation allergy, and the other for food allergy) at the same time using a small amount of whole blood. For 158 patients of inhalation allergy and 135 patients of food allergy, they were evaluated by HRT, CAP-RAST, skin test, and provocation test. The concordance of HRT, CAP-RAST, and skin test were 78%, 72%, and 62% in inhalation allergy, and 84%, 71%, and 81% in food allergy, respectively. The specificity of HRT, CAP-RAST, and skin test were 63%, 37%, and 19% in inhalation allergy, and 92%, 63%, and 83% in food allergy, respectively. The positive predictive value of HRT, CAP-RAST, and skin test were 79%, 71%, and 63%, respectively. The false positive ratio of HRT (14%) was lower than that of CAP-RAST (42%). The sensitivity of CAP-RAST was higher than that of HRT. In addition, we experienced a case of patient who showed significant improvement by treatment. At initial stage, not only the symptoms were erythema and scratching but also HRT, CAP-RAST, and skin test resulted in positive. Four months later, he had no allergic symptoms, HRT resulted in negative, but CAP-RAST and skin test resulted in still positive. From these results, we concluded that CAP-RAST is good for screening of etiological allergens and that HRT is a useful diagnostic method for the confirmation of a clinical allergy.

Evaluation of the medicinal use of clay minerals as antibacterial agents.

PubMed

Williams, Lynda B; Haydel, Shelley E

2010-07-01

Natural clays have been used to heal skin infections since the earliest recorded history. Recently our attention was drawn to a clinical use of French green clay (rich in Fe-smectite) for healing Buruli ulcer, a necrotizing fasciitis ('flesh-eating' infection) caused by Mycobacterium ulcerans. These clays and others like them are interesting as they may reveal an antibacterial mechanism that could provide an inexpensive treatment for this and other skin infections, especially in global areas with limited hospitals and medical resources.Microbiological testing of two French green clays, and other clays used traditionally for healing, identified three samples that were effective at killing a broad-spectrum of human pathogens. A clear distinction must be made between 'healing clays' and those we have identified as antibacterial clays. The highly adsorptive properties of many clays may contribute to healing a variety of ailments, although they are not antibacterial. The antibacterial process displayed by the three identified clays is unknown. Therefore, we have investigated the mineralogical and chemical compositions of the antibacterial clays for comparison with non-antibacterial clays in an attempt to elucidate differences that may lead to identification of the antibacterial mechanism(s).The two French green clays used to treat Buruli ulcer, while similar in mineralogy, crystal size, and major element chemistry, have opposite effects on the bacterial populations tested. One clay deposit promoted bacterial growth whereas another killed the bacteria. The reasons for the difference in antibacterial properties thus far show that the bactericidal mechanism is not physical (e.g., an attraction between clay and bacteria), but by a chemical transfer or reaction. The chemical variables are still under investigation.Cation exchange experiments showed that the antibacterial component of the clay can be removed, implicating exchangeable cations in the antibacterial process. Furthermore, aqueous leachates of the antibacterial clays effectively kill the bacteria. Progressively heating the clay leads first to dehydration (200 degrees C), then dehydroxylation (550 degrees C or more), and finally to destruction of the clay mineral structure by (~900 degrees C). By identifying the elements lost after each heating step, and testing the bactericidal effect of the heated product, we eliminated many toxins from consideration (e.g., microbes, organic compounds, volatile elements) and identified several redox-sensitive refractory metals that are common among antibacterial clays. We conclude that the pH and oxidation state buffered by the clay mineral surfaces is key to controlling the solution chemistry and redox related reactions occurring at the bacterial cell wall.

Mars Seasonal Polar Caps as a Test of the Equivalence Principle

NASA Technical Reports Server (NTRS)

Rubincam, Daivd Parry

2011-01-01

The seasonal polar caps of Mars can be used to test the equivalence principle in general relativity. The north and south caps, which are composed of carbon dioxide, wax and wane with the seasons. If the ratio of the inertial to gravitational masses of the caps differs from the same ratio for the rest of Mars, then the equivalence principle fails, Newton's third law fails, and the caps will pull Mars one way and then the other with a force aligned with the planet's spin axis. This leads to a secular change in Mars's along-track position in its orbit about the Sun, and to a secular change in the orbit's semimajor axis. The caps are a poor E6tv6s test of the equivalence principle, being 4 orders-of-magnitude weaker than laboratory tests and 7 orders-of-magnitude weaker than that found by lunar laser ranging; the reason is the small mass of the caps compared to Mars as a whole. The principal virtue of using Mars is that the caps contain carbon, an element not normally considered in such experiments. The Earth with its seasonal snow cover can also be used for a similar test.

Anatomical knowledge gain through a clay-modeling exercise compared to live and video observations.

PubMed

Kooloos, Jan G M; Schepens-Franke, Annelieke N; Bergman, Esther M; Donders, Rogier A R T; Vorstenbosch, Marc A T M

2014-01-01

Clay modeling is increasingly used as a teaching method other than dissection. The haptic experience during clay modeling is supposed to correspond to the learning effect of manipulations during exercises in the dissection room involving tissues and organs. We questioned this assumption in two pretest-post-test experiments. In these experiments, the learning effects of clay modeling were compared to either live observations (Experiment I) or video observations (Experiment II) of the clay-modeling exercise. The effects of learning were measured with multiple choice questions, extended matching questions, and recognition of structures on illustrations of cross-sections. Analysis of covariance with pretest scores as the covariate was used to elaborate the results. Experiment I showed a significantly higher post-test score for the observers, whereas Experiment II showed a significantly higher post-test score for the clay modelers. This study shows that (1) students who perform clay-modeling exercises show less gain in anatomical knowledge than students who attentively observe the same exercise being carried out and (2) performing a clay-modeling exercise is better in anatomical knowledge gain compared to the study of a video of the recorded exercise. The most important learning effect seems to be the engagement in the exercise, focusing attention and stimulating time on task. © 2014 American Association of Anatomists.

7 CFR 1714.7 - Interest rate cap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Interest rate cap. 1714.7 Section 1714.7 Agriculture... PRE-LOAN POLICIES AND PROCEDURES FOR INSURED ELECTRIC LOANS General § 1714.7 Interest rate cap. Except... section, or both the rate disparity test for the interest rate cap and the consumer income test set forth...

Evaluation of the medicinal use of clay minerals as antibacterial agents

PubMed Central

Williams, Lynda B.; Haydel, Shelley E.

2010-01-01

Natural clays have been used to heal skin infections since the earliest recorded history. Recently our attention was drawn to a clinical use of French green clay (rich in Fe-smectite) for healing Buruli ulcer, a necrotizing fasciitis (‘flesh-eating’ infection) caused by Mycobacterium ulcerans. These clays and others like them are interesting as they may reveal an antibacterial mechanism that could provide an inexpensive treatment for this and other skin infections, especially in global areas with limited hospitals and medical resources. Microbiological testing of two French green clays, and other clays used traditionally for healing, identified three samples that were effective at killing a broad-spectrum of human pathogens. A clear distinction must be made between ‘healing clays’ and those we have identified as antibacterial clays. The highly adsorptive properties of many clays may contribute to healing a variety of ailments, although they are not antibacterial. The antibacterial process displayed by the three identified clays is unknown. Therefore, we have investigated the mineralogical and chemical compositions of the antibacterial clays for comparison with non-antibacterial clays in an attempt to elucidate differences that may lead to identification of the antibacterial mechanism(s). The two French green clays used to treat Buruli ulcer, while similar in mineralogy, crystal size, and major element chemistry, have opposite effects on the bacterial populations tested. One clay deposit promoted bacterial growth whereas another killed the bacteria. The reasons for the difference in antibacterial properties thus far show that the bactericidal mechanism is not physical (e.g., an attraction between clay and bacteria), but by a chemical transfer or reaction. The chemical variables are still under investigation. Cation exchange experiments showed that the antibacterial component of the clay can be removed, implicating exchangeable cations in the antibacterial process. Furthermore, aqueous leachates of the antibacterial clays effectively kill the bacteria. Progressively heating the clay leads first to dehydration (200°C), then dehydroxylation (550°C or more), and finally to destruction of the clay mineral structure by (~900°C). By identifying the elements lost after each heating step, and testing the bactericidal effect of the heated product, we eliminated many toxins from consideration (e.g., microbes, organic compounds, volatile elements) and identified several redox-sensitive refractory metals that are common among antibacterial clays. We conclude that the pH and oxidation state buffered by the clay mineral surfaces is key to controlling the solution chemistry and redox related reactions occurring at the bacterial cell wall. PMID:20640226

Retention Strength of Conical Welding Caps for Fixed Implant-Supported Prostheses.

PubMed

Nardi, Diego; Degidi, Marco; Sighinolfi, Gianluca; Tebbel, Florian; Marchetti, Claudio

This study evaluated the retention strength of welding caps for Ankylos standard abutments using a pull-out test. Each sample consisted of an implant abutment and its welding cap. The tests were performed with a Zwick Roell testing machine with a 1-kN load cell. The retention strength of the welding caps increased with higher abutment diameters and higher head heights and was comparable or superior to the values reported in the literature for the temporary cements used in implant dentistry. Welding caps provide a reliable connection between an abutment and a fixed prosthesis without the use of cement.

Association of Medical Liability Reform With Clinician Approach to Coronary Artery Disease Management.

PubMed

Farmer, Steven A; Moghtaderi, Ali; Schilsky, Samantha; Magid, David; Sage, William; Allen, Nori; Masoudi, Frederick A; Dor, Avi; Black, Bernard

2018-06-06

Physicians often report practicing defensive medicine to reduce malpractice risk, including performing expensive but marginally beneficial tests and procedures. Although there is little evidence that malpractice reform affects overall health care spending, it may influence physician behavior for specific conditions involving clinical uncertainty. To examine whether reducing malpractice risk is associated with clinical decisions involving coronary artery disease testing and treatment. Difference-in-differences design, comparing physician-specific changes in coronary artery disease testing and treatment in 9 new-cap states that adopted damage caps between 2003 and 2005 with 20 states without caps. We used the 5% national Medicare fee-for-service random sample between 1999 and 2013. Physicians (n = 75 801; 36 647 in new-cap states) who ordered or performed 2 or more coronary angiographies. Data were analyzed from June 2015 to January 2018. Changes in ischemic evaluation rates for possible coronary artery disease, type of initial evaluation (stress testing or coronary angiography), progression from stress test to angiography, and progression from ischemic evaluation to revascularization (percutaneous coronary intervention or coronary artery bypass grafting). We studied 36 647 physicians in new-cap states and 39 154 physicians in no-cap states. New-cap states had younger populations, more minorities, lower per-capita incomes, fewer physicians per capita, and lower managed care penetration. Following cap adoption, new-cap physicians reduced invasive testing (angiography) as a first diagnostic test compared with control physicians (relative change, -24%; 95% CI, -40% to -7%; P = .005) with an offsetting increase in noninvasive stress testing (7.8%; 95% CI, -3.6% to 19.3%; P = .17), and referred fewer patients for angiography following stress testing (-21%; 95% CI, -40% to -2%; P = .03). New-cap physicians also reduced revascularization rates after ischemic evaluation (-23%; 95% CI, -40% to -4%; P = .02; driven by fewer percutaneous coronary interventions). Changes in overall ischemic evaluation rates were similar for new-cap and control physicians (-0.05%; 95% CI, -8.0% to 7.9%; P = .98). Physicians substantially altered their approach to coronary artery disease testing and follow-up after initial ischemic evaluations following adoption of damage caps. They performed a similar number of ischemic evaluations but conducted fewer initial left heart catheterizations, referred fewer stress-tested patients for left heart catheterizations, and referred fewer patients for revascularization. These findings suggest that physicians tolerate greater clinical uncertainty in coronary artery disease testing and treatment if they face lower malpractice risk.

Coupled Heat and Moisture Transport Simulation on the Re-saturation of Engineered Clay Barrier

NASA Astrophysics Data System (ADS)

Huang, W. H.; Chuang, Y. F.

2014-12-01

Engineered clay barrier plays a major role for the isolation of radioactive wastes in a underground repository. This paper investigates the resaturation processes of clay barrier, with emphasis on the coupling effects of heat and moisture during the intrusion of groundwater to the repository. A reference bentonite and a locally available clay were adopted in the laboratory program. Soil suction of clay specimens was measured by psychrometers embedded in clay specimens and by vapor equilibrium technique conducted at varying temperatures so as to determine the soil water characteristic curves of the two clays at different temperatures. And water uptake tests were conducted on clay specimens compacted at various densities to simulate the intrusion of groundwater into the clay barrier. Using the soil water characteristic curve, an integration scheme was introduced to estimate the hydraulic conductivity of unsaturated clay. It was found that soil suction decreases as temperature increases, resulting in a reduction in water retention capability. The finite element method was then employed to carry out the numerical simulation of the saturation process in the near field of a repository. Results of the numerical simulation were validated using the degree of saturation profile obtained from the water uptake tests on the clays. The numerical scheme was then extended to establish a model simulating the resaturation process after the closure of a repository. Finally, the model was then used to evaluate the effect of clay barrier thickness on the time required for groundwater to penetrate the clay barrier and approach saturation. Due to the variation in clay suction and thermal conductivity with temperature of clay barrier material, the calculated temperature field shows a reduction as a result of incorporating the hydro-properties in the calculations.

Perceptions of Prostate Cancer Fatalism and Screening Behavior Between United States-Born and Caribbean-Born Black Males

PubMed Central

Cobran, Ewan K.; Wutoh, Anthony K.; Lee, Euni; Odedina, Folakemi T.; Ragin, Camille; Aiken, William; Godley, Paul A.

2013-01-01

Cancer fatalism is believed to be a major barrier for cancer screening in Black males. Therefore, the purpose of this study was to compare perceptions of prostate cancer (CaP) fatalism and predictors of CaP screening with Prostate Specific Antigen (PSA) testing between U.S.-born and Caribbean-born Black males. The Powe Fatalism Inventory and the Personal Integrative Model of CaP Disparity Survey were used to collect the following data from males in South Florida. Multivariate logistic regression models were constructed to examine the statistically significant predictors of CaP screening. A total of 211 U.S.-born and Caribbean-born Black males between ages 39–75 were recruited. Nativity was not a significant predictor of CaP screening with PSA testing within the last year (Odds ratio [OR] = 0.80, 95 % confidence interval [CI] = 0.26, 2.48, p = 0.70). Overall, higher levels of CaP fatalism were not a significant predictor of CaP screening with PSA testing within the last year (OR = 1.37, 95 % CI = 0.48, 3.91, p = 0.56). The study results suggest that nativity did not influence CaP screening with PSA testing. However, further studies are needed to evaluate the association between CaP screening behavior and levels of CaP fatalism. PMID:23576029

Mars seasonal polar caps as a test of the equivalence principle

NASA Astrophysics Data System (ADS)

Rubincam, David Parry

2011-08-01

The seasonal polar caps of Mars can be used to test the equivalence principle in general relativity. The north and south caps, which are composed of carbon dioxide, wax and wane with the seasons. If the ratio of the inertial (passive) to gravitational (active) masses of the caps differs from the same ratio for the rest of Mars, then the equivalence principle fails, Newton’s third law fails, and the caps will pull Mars one way and then the other with a force aligned with the planet’s spin axis. This leads to a secular change in Mars’s along-track position in its orbit about the Sun, and to a secular change in the orbit’s semimajor axis. The caps are a poor Eötvös test of the equivalence principle, being 4 orders-of-magnitude weaker than laboratory tests and 7 orders-of-magnitude weaker than that found by lunar laser ranging; the reason is the small mass of the caps compared to Mars as a whole. The principal virtue of using Mars is that the caps contain carbon, an element not normally considered in such experiments. The Earth with its seasonal snow cover can also be used for a similar test.

Comparison of the Performance of Skin Prick, ImmunoCAP, and ISAC Tests in the Diagnosis of Patients with Allergy.

PubMed

Griffiths, Rebecca L M; El-Shanawany, Tariq; Jolles, Stephen R A; Selwood, Clive; Heaps, Adrian G; Carne, Emily M; Williams, Paul E

2017-01-01

Allergy is diagnosed from typical symptoms, and tests are performed to incriminate the suspected precipitant. Skin prick tests (SPTs) are commonly performed, inexpensive, and give immediate results. Laboratory tests (ImmunoCAP) for serum allergen-specific IgE antibodies are usually performed more selectively. The immuno-solid phase allergen chip (ISAC) enables testing for specific IgE against multiple allergen components in a multiplex assay. We retrospectively analysed clinic letters, case notes, and laboratory results of 118 patients attending the National Adult Allergy Service at the University Hospital of Wales who presented diagnostic difficulty, to evaluate which testing strategy (SPT, ImmunoCAP, or ISAC) was the most appropriate to use to confirm the diagnosis in these complex patients, evaluated in a "real-life" clinical service setting. In patients with nut allergy, the detection rates of SPTs (56%) and ISAC (65%) were lower than those of ImmunoCAP (71%). ISAC had a higher detection rate (88%) than ImmunoCAP (69%) or SPT (33%) in the diagnosis of oral allergy syndrome. ImmunoCAP test results identified all 9 patients with anaphylaxis due to wheat allergy (100%), whereas ISAC was positive in only 6 of these 9 (67%). In this difficult diagnostic group, the ImmunoCAP test should be the preferred single test for possible allergy to nuts, wheat, other specific foods, and anaphylaxis of any cause. In these conditions, SPT and ISAC tests give comparable results. The most useful single test for oral allergy syndrome is ISAC, and SPT should be the preferred test for latex allergy. © 2017 S. Karger AG, Basel.

Tension and Bending Testing of an Integral T-Cap for Stitched Composite Airframe Joints

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Leone, Frank A., Jr.

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in large-scale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

Assessment of the mechanical properties of sisal fiber-reinforced silty clay using triaxial shear tests.

PubMed

Wu, Yankai; Li, Yanbin; Niu, Bin

2014-01-01

Fiber reinforcement is widely used in construction engineering to improve the mechanical properties of soil because it increases the soil's strength and improves the soil's mechanical properties. However, the mechanical properties of fiber-reinforced soils remain controversial. The present study investigated the mechanical properties of silty clay reinforced with discrete, randomly distributed sisal fibers using triaxial shear tests. The sisal fibers were cut to different lengths, randomly mixed with silty clay in varying percentages, and compacted to the maximum dry density at the optimum moisture content. The results indicate that with a fiber length of 10 mm and content of 1.0%, sisal fiber-reinforced silty clay is 20% stronger than nonreinforced silty clay. The fiber-reinforced silty clay exhibited crack fracture and surface shear fracture failure modes, implying that sisal fiber is a good earth reinforcement material with potential applications in civil engineering, dam foundation, roadbed engineering, and ground treatment.

Clays causing adhesion with tool surfaces during mechanical tunnel driving

NASA Astrophysics Data System (ADS)

Spagnoli, G.; Fernández-Steeger, T.; Stanjek, H.; Feinendegen, M.; Post, C.; Azzam, R.

2009-04-01

During mechanical excavation with a tunnel boring machine (TBM) it is possible that clays stick to the cutting wheel and to other metal parts. The resulting delays in the progress of construction work, cause great economic damage and often disputes between the public awarding authorities and executing companies. One of the most important factors to reduce successfully the clay adhesion is the use of special polymers and foams. But why does the clay stick to the metal parts? A first step is to recognize which kind of clay mineralogy shows serious adhesion problems. The mechanical properties of clay and clay suspensions are primarily determined by surface chemistry and charge distribution at the interfaces, which in turn affect the arrangement of the clay structure. As we know, clay is a multi-phase material and its behaviour depends on numerous parameters such as: clay mineralogy, clay fraction, silt fraction, sand fraction, water content, water saturation, Atterberg limits, sticky limit, activity, cation exchange capacity, degree of consolidation and stress state. It is therefore likely that adhesion of clay on steel is also affected by these clay parameters. Samples of clay formations, which caused problems during tunnel driving, will be analyzed in laboratory. Mineralogical analyses (diffractometry, etc.) will be carried out to observe which minerals are responsible for adherence problems. To manipulate the physical properties, batch tests will be carried out in order to eliminate or reduce the adhesion on tool surfaces through variation of the zeta potential. Second step is the performance of vane shear tests on clay samples. Different pore fluid (distilled water, pure NaCl solution, ethanol and methanol) will be used to study the variation of the mechanical behaviour of clay depending on the dielectric constant of the fluids. This project is funded by the German Federal Ministry of Education and Research (BMBF) and the DFG (German Research Foundation) in the frame of the programme GEOTECHNOLOGIEN.

Color measurement of methylene blue dye/clay mixtures and its application using economical methods

NASA Astrophysics Data System (ADS)

Milosevic, Maja; Kaludjerovic, Lazar; Logar, Mihovil

2016-04-01

Identifying the clay mineral components of clay materials by staining tests is rapid and simple, but their applicability is restricted because of the mutual interference of the common components of clay materials and difficulties in color determination. The change of color with concentration of the dye is related to the use of colorants as a field test for identifying clay minerals and has been improved over the years to assure the accuracy of the tests (Faust G. T., 1940). The problem of measurement and standardization of color may be solved by combination of colors observed in staining tests with prepared charts of color chips available in the Munsell Book of Color, published by Munsell Color Co. Under a particular set of illumination conditions, a human eye can achieve an approximate match between the color of the dyed clay sample and that of a standard color chip, even though they do have different spectral reflectance characteristics. Experiments were carried out with diffuse reflectance spectroscopy on selected clay samples (three montmorillonite, three kaolinite and one mix-layer clay samples) saturated with different concentration of methylene blue dye solution. Dominant wavelength and purity of the color was obtained on oriented dry samples and calculated by use of the I. C. I. (x, y) - diagram in the region of 400-700 nm (reflectance spectra) without MB and after saturation with different concentrations of MB solutions. Samples were carefully photographed in the natural light environment and processed with user friendly and easily accessible applications (Adobe color CC and ColorHexa encyclopedia) available for android phones or tablets. Obtained colors were compared with Munsell standard color chips, RGB and Hexa color standards. Changes in the color of clay samples in their interaction with different concentration of the applied dye together with application of economical methods can still be used as a rapid fieldwork test. Different types of clay minerals can be distinguished by application of at least three concentrations of the methylene blue dye on the same sample and observing the color change in comparison with standardized color chips that can be easily obtained and free of charge. If the color tests are properly used in conjunction with other more complex analytical procedures, they can be helpful addition in identification of different clay minerals, especially montmorillonite and kaolinite minerals. - Faust G. T., 1940, Staining of clay minerals as a rapid means of identification in natural and beneficiated products, U. S. Bur. Mines, Investigation Report. N0.3522 - Munsell Color, Munsell Book of Color, 1942. Macbeth Division of Kollmorgen Corporation, Maryland, U.S.A. - https://color.adobe.com/create/color-wheel/ - http://www.colorhexa.com/

Fire retardancy assessment of polypropylene composite filed with nano clay prepared from Iraqi bentonite

NASA Astrophysics Data System (ADS)

Kareem Salih, Watheq

2018-05-01

Fire retardants have an extraordinary importance because of their role in saving the people, property and reducing the damages and minimizing the dangers resulting from fires and burning of polymeric composites which are used in different civil and industrial fields. The work in this paper can be divided into two main stages. In first one nano-clay was manufactured from Iraqi bentonite and it was characterized using AFM, XRD, XRF, SEM, and BET. The AFM test showed the particle size of prepared nano clay was about 99.25 nm. In the second stage, polypropylene/nano clay composites at three low loading percents (0%,2%,4%,6%) were formulated via twin screw extruder. The fire retardancy tests included burning rate according to ASTM:D-635 and maximum flame height of flame according to ASTM:D-3014. Besides, the mechanical tests and thermal behavior of prepared samples were investigated. The results showed that (4%) of nano-clay had the maximum fire retardancy and while at (2%) loading, the maximum value of tensile strength and Yong modulus were obtained. The maximum heat of fusion was recorded for 6% nano clay sample. The final results assessment confirmed on the possibility of using low loadings of prepared nano clay to improve the fire retardancy, mechanical and thermal properties successfully.

Development of High Capacity Enterosorbents for Aflatoxin B1 and Other Hazardous Chemicals.

PubMed

Wang, Meichen; Maki, Cody R; Deng, Youjun; Tian, Yanan; Phillips, Timothy D

2017-09-18

Previously, a calcium montmorillonite clay (NovaSil) included in the diet of animals has been shown to bind aflatoxin B1 (AfB1) and reduce the symptoms of aflatoxicosis. To investigate and improve the capacity and efficacy of clay-based materials as aflatoxin sorbents, we developed and tested calcium and sodium montmorillonite clays amended with nutrients including l-carnitine and choline. Also, we determined the sorption of AfB1 by isothermal analysis and tested the ability of these amended sorbents to protect adult hydra from AfB1 toxicity. The results showed that exchanging montmorillonite clays with l-carnitine and choline inhibited swelling of the clays and increased the sorption capacity and efficacy of clay surfaces for AfB1. Results from dehydroxylated and heat-collapsed clays suggested that AfB1 was primarily adsorbed in the clay interlayer, as predicted from thermodynamic calculations and computational modeling. The hydra bioassay further indicated that the modified clays can significantly protect adult hydra from AfB1 with as low as 0.005% clay inclusion. This enterosorbent therapy may also be applied to screen hazardous chemicals such as pesticides and PAHs based on similar sorption mechanisms. Taken together, enterosorbent therapy could be delivered in nutritional supplements, foods that are vulnerable to aflatoxin contamination, flavored liquids and animal feeds during emergencies and outbreaks of acute aflatoxicosis, and as a screening model for hazardous environmental chemicals.

Evaluation of the healing activity of therapeutic clay in rat skin wounds.

PubMed

Dário, Giordana Maciel; da Silva, Geovana Gomes; Gonçalves, Davi Ludvig; Silveira, Paulo; Junior, Adilson Teixeira; Angioletto, Elidio; Bernardin, Adriano Michael

2014-10-01

The use of clays for therapeutic practice is widespread in almost all regions of the world. In this study the physicochemical and microbiological healing characteristics of a clay from Ocara, Brazil, popularly used for therapeutic uses, were analyzed. The presence of Ca, Mg, Al, Fe, and Si was observed, which initially indicated that the clay had potential for therapeutic use. The average particle size of the clay (26.3 μm) can induce the microcirculation of the skin and the XRD analysis shows that the clay is formed by kaolinite and illite, a swelling clay. During the microbiological evaluation there was the need to sterilize the clay for later incorporation into the pharmaceutical formula. The accelerated stability test at 50°C for 3 months has showed that the pharmaceutical formula remained stable with a shelf life of two years. After the stability test the wound-healing capacity of the formulation in rats was evaluated. It was observed that the treatment made with the formulation containing the Ocara clay showed the best results since the formula allowed greater formation of collagen fibers and consequent regeneration of the deep dermis after seven days of treatment and reepithelialization and continuous formation of granulation tissue at the 14th day. Copyright © 2014 Elsevier B.V. All rights reserved.

Influence of nanoclay on interlaminar shear strength and fracture toughness of glass fiber reinforced nanocomposites

NASA Astrophysics Data System (ADS)

Senthil Kumar, M. S.; Chithirai Pon Selvan, M.; Sampath, P. S.; Raja, K.; Balasundaram, K.

2018-04-01

Multilayer glass fiber reinforced polymer (GFRP) laminates filled with nanoclay was manufactured with compression moulding machine. In the present work, five kinds of nanoclay (Cloisite 25A) loadings viz. 2, 4, 6, 8 and 10% on weight basis of epoxy resin were employed to modify the interlaminar shear strength (ILSS), critical energy release rate (GIc) and impact energy properties of GFRP laminates. Experimental results obtained from ILSS test on clay filled GFRP confirm that the superior strength was attained at low clay content of 155.10 MPa. Furthermore, the mode I interlaminar fracture toughness test conducted on DCB specimens revealed that the commanding improvement of GIc was obtained at 2 wt.% clay content level. On the other hand, both ILSS and fracture toughness was getting reduced at higher clay loadings. At last, the impact strength of the test samples was investigated by using Izod impact test apparatus and observed that the impact energy was increased by 44.39% for 2 wt.% and followed by 24.87% for 4 wt.% clay loadings.

T-Cap Pull-Off and Bending Behavior for Stitched Structure

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Leone, Frank A., Jr.

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in largescale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

Compressibility characteristics of Sabak Bernam Marine Clay

NASA Astrophysics Data System (ADS)

Lat, D. C.; Ali, N.; Jais, I. B. M.; Baharom, B.; Yunus, N. Z. M.; Salleh, S. M.; Azmi, N. A. C.

2018-04-01

This study is carried out to determine the geotechnical properties and compressibility characteristics of marine clay collected at Sabak Bernam. The compressibility characteristics of this soil are determined from 1-D consolidation test and verified by existing correlations by other researchers. No literature has been found on the compressibility characteristics of Sabak Bernam Marine Clay. It is important to carry out this study since this type of marine clay covers large coastal area of west coast Malaysia. This type of marine clay was found on the main road connecting Klang to Perak and the road keeps experiencing undulation and uneven settlement which jeopardise the safety of the road users. The soil is indicated in the Generalised Soil Map of Peninsular Malaysia as a CLAY with alluvial soil on recent marine and riverine alluvium. Based on the British Standard Soil Classification and Plasticity Chart, the soil is classified as a CLAY with very high plasticity (CV). Results from laboratory test on physical properties and compressibility parameters show that Sabak Bernam Marine Clay (SBMC) is highly compressible, has low permeability and poor drainage characteristics. The compressibility parameters obtained for SBMC is in a good agreement with other researchers in the same field.

Positive urinary antigen tests for Streptococcus pneumoniae in community-acquired pneumonia: a 7-year retrospective evaluation of health care cost and treatment consequences.

PubMed

Engel, M F; van Velzen, M; Hoepelman, A I M; Thijsen, S; Oosterheert, J J

2013-04-01

A positive pneumococcal urinary antigen test (PUAT) for Streptococcus pneumoniae allows an early switch from empiric to targeted treatment in hospitalised community-acquired pneumonia (CAP) patients. The economic and treatment consequences of this widespread implemented test are, however, unknown. We retrospectively evaluated all tests performed since its introduction in two teaching hospitals. Data on patient characteristics, treatment, admission and outcome were retrieved from the electronic patient files. Test benefits were expressed as the number of days that targeted therapy (i.e. penicillin) was administered to hospitalised CAP patients due to a positive PUAT. This calculation was based on the timing of the PUAT and the initiation of targeted therapy. Subsequently, we performed two direct cost analyses from a hospital perspective, first including tests performed for CAP only, and second including costs of all (excessive) tests. Between 2005 and 2012, 3,479 PUATs were performed, of which 1,907 (55 %) were for CAP. A total of 1,638 PUATs (86 %) were negative and 269 (14 %) were positive. Fifty-two (19 %) positive tests were excluded. In 75 (35 %) of the 217 remaining positive tests, a positive PUAT led to targeted treatment during 293 cumulative admission days. Testing costs for CAP only were €131 per targeted treatment day. These costs were €257 if local protocol dictated PUAT use for all CAP cases, as opposed to €72 if the test was reserved for severe cases only. When including all tests, PUAT costs were €254 per targeted treatment day. Therefore, improving the selective use of the PUAT in hospitalised CAP patients may lead to increased (cost-)efficiency.

Resistivity imaging of Aluto-Langano geothermal field using 3-D magnetotelluric inversion

NASA Astrophysics Data System (ADS)

Cherkose, Biruk Abera; Mizunaga, Hideki

2018-03-01

Magnetotelluric (MT) method is a widely used geophysical method in geothermal exploration. It is used to image subsurface resistivity structures from shallow depths up to several kilometers of depth. Resistivity imaging using MT method in high-enthalpy geothermal systems is an effective tool to identify conductive clay layers that cover the geothermal systems and to detect a potential reservoir. A resistivity model is vital for deciding the location of pilot and production sites at the early stages of a geothermal project. In this study, a 3-D resistivity model of Aluto-Langano geothermal field was constructed to map structures related to a geothermal resource. The inversion program, ModEM was used to recover the 3-D resistivity model of the study area. The 3-D inversion result revealed the three main resistivity structures: a high-resistivity surface layer related to unaltered volcanic rocks at shallow depth, underlain by a conductive zone associated with the presence of conductive clay minerals, predominantly smectite. Beneath the conductive layer, the resistivity increases gradually to higher values related to the formation of high-temperature alteration minerals such as chlorite and epidote. The resistivity model recovered from 3-D inversion in Aluto-Langano corresponds very well to the conceptual model for high-enthalpy volcanic geothermal systems. The conductive clay cap is overlying the resistive propylitic upflow zone as confirmed by the geothermal wells in the area.

Effects of Kaolin Clay on the Mechanical Properties of Asphaltic Concrete AC14

NASA Astrophysics Data System (ADS)

Abdullah, M. E.; Ramadhansyah, P. J.; Rafsanjani, M. H.; Norhidayah, A. H.; Yaacob, H.; Hainin, M. R.; Warid, M. N. Mohd; Satar, M. K. I. Mohd; Aziz, Md Maniruzzaman A.; Mashros, N.

2018-04-01

This study investigated the effect of kaolin clay on the mechanical properties of asphaltic concrete AC14 through Marshall Stability, resilient modulus, and dynamic creep tests. Four replacement levels of kaolin clay (2%, 4%, 6%, and 8% by weight of the binder) were considered. Kaolin clay functioned as an effective filler replacement material to increase the mechanical properties of asphalt mixtures. Asphaltic concrete with 2% to 4% kaolin clay replacement level exhibited excellent performance with good stability, resilient modulus, and creep stiffness.

30 CFR 250.1608 - Well casing and cementing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... rock casing, (iv) Bobtail cap rock casing (required when the cap rock casing does not penetrate into the cap rock), (v) Second cap rock casing (brine wells), and (vi) Production liner. (2) The lessee... lessee shall initiate remedial action as approved by the District Manager. For cap rock casing, the test...

30 CFR 250.1608 - Well casing and cementing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... rock casing, (iv) Bobtail cap rock casing (required when the cap rock casing does not penetrate into the cap rock), (v) Second cap rock casing (brine wells), and (vi) Production liner. (2) The lessee... lessee shall initiate remedial action as approved by the District Manager. For cap rock casing, the test...

30 CFR 250.1608 - Well casing and cementing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... rock casing, (iv) Bobtail cap rock casing (required when the cap rock casing does not penetrate into the cap rock), (v) Second cap rock casing (brine wells), and (vi) Production liner. (2) The lessee... lessee shall initiate remedial action as approved by the District Manager. For cap rock casing, the test...

Slope Stability of Geosynthetic Clay Liner Test Plots

EPA Science Inventory

Fourteen full-scale field test plots containing five types of geosynthetic clay liners (GCLs) were constructed on 2H:IV and 3H:IV slopes for the purpose of assessing slope stability. The test plots were designed to simulate typical final cover systems for landfill. Slides occurr...

Lateral pile cap load tests with gravel backfill of limited width.

DOT National Transportation Integrated Search

2010-08-01

This study investigated the increase in passive force produced by compacting a dense granular fill adjacent to a pile cap or abutment wall when the surrounding soil is in a relative loose state. Lateral load tests were performed on a pile cap with th...

Expanded clay hot mix study : final report: part I.

DOT National Transportation Integrated Search

1969-04-01

This is part I of a two part final report on expanded clay hot mix to: (1) evaluate the use of various expanded clay bituminous mixtures under high traffic counts, (2) accumulate through experience testing, suitable information on the physical proper...

The Influence of SAND’s Gradation and Clay Content of Direct Sheart Test on Clayey Sand

NASA Astrophysics Data System (ADS)

Wibisono, Gunawan; Agus Nugroho, Soewignjo; Umam, Khairul

2018-03-01

The shear strength of clayey-sand can be affected by several factors, e.g. gradation, density, moisture content, and the percentage of clay and sand fraction. The same percentage of clay and sand fraction in clayey-sand mixtures may have different shear strengths due to those factors. This research aims to study the effect of clay content on sand that cause the change of its shear strength. Samples consisted of different clay and sand fractions were reconstituted at a certain moisture content. Sand fractions varied from well-graded to poorly-graded sand. Shear strength was measured in terms of the direct shear test. Prior to the test, surcharge loads were applied to represent overburden pressures. Shear strength results and their components (i.e. Cohesion and internal angle of friction) were correlated with physical properties of samples (i.e. grading coefficient of curvature, coefficient of uniformity, and density). Results showed that samples classified as well-graded and dense sand had higher shear strength. In the other hand, the shear strengths decreased when the mixtures became poorly-graded and less dense. The inclusion of the clay fraction increased cohesion component and decreased internal angle of friction.

Synthesis and innovation of PLA/clay nanocomposite characterization againts to mechanical and thermal properties

NASA Astrophysics Data System (ADS)

Salim, S.; Agusnar, H.; Wirjosentono, B.; Tamrin; Marpaung, H.; Rihayat, T.; Nurhanifa; Adriana

2018-03-01

Plastic polymer is one of the most dominant materials of daily human activities because of its multifunctional nature, light and strong and anti-corrosion so it is easy to apply in various equipment. Plastic is generally derived from petroleum material so it is nonbiodegradable. Therefore, this study aims to create a breakthrough of natural and biodegradable biodegradable plastic materials from plant starch (pisok kepok starch) with the help of 3 types of acid (HNO3, HCl and H2SO4) called Poly Lactid Acid (PLA). PLA is enhanced by mixing with a clay material with a variation of 1, 3 and 5% composition to form a PLA / Clay Nanocomposite material which is expected to have superior properties and resemble conventional plastics in general. Several types of characterization were performed to see the quality of the resulting material including tensile strength test with UTM tool, thermal endurance test with TGA tool, morphological structure test using SEM tool and additional test to see filler clay quality through X-RD tool. Based on the characterization of tensile and thermal test, 5B nanocomposite with addition of 5% clay and HCl acid aid showed the best tensile strength of 36 Mpa and the highest stability was 446,63 oC. Based on the results of morphological analysis of the best samples (5B) showed good interface ties. Meanwhile, based on the results of filler analysis, the opening of clay layer d-spacing occurred at 0.355 nm.

Design and implementation of the protective cap/biobarrier experiment at the Idaho National Engineering Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Limbach, W.E.; Ratzlaff, T.D.; Anderson, J.E.

1994-12-31

The Protective Cap/Biobarrier Experiment (PCBE), initiated in 1993 at the Idaho National Engineering Laboratory (INEL), is a strip-split plot experiment with three replications designed to rigorously test a 2.0-m loessal soil cap against a cap recommended by the US Environmental Protection Agency and two caps with biological intrusion barriers. Past research at INEL indicates that it should be possible to exclude water from buried wastes using natural materials and natural processes in arid environments rather than expensive materials (geotextiles) and highly engineered caps. The PCBE will also test the effects of two vegetal covers and three irrigation levels on capmore » performance. Drainage pans, located at the bottom of each plot, will monitor cap failure. Soil water profiles will be monitored biweekly by neutron probe and continuously by time domain reflectometry. The performance of each cap design will be monitored under a variety of conditions through 1998. From 1994 to 1996, the authors will assess plant establishment, rooting depths, patterns of moisture extraction and their interactions among caps, vegetal covers, and irrigation levels. In 1996, they will introduce ants and burrowing mammals to test the structural integrity of each cap design. In 1998, the authors will apply sufficient water to determine the failure limit for each cap design. The PCBE should provide reliable knowledge of the performances of the four cap designs under a variety of conditions and aid in making hazardous-waste management decisions at INEL and at disposal sites in similar environments.« less

Anisotropic Behaviour of Opalinus Clay Through Consolidated and Drained Triaxial Testing in Saturated Conditions

NASA Astrophysics Data System (ADS)

Favero, Valentina; Ferrari, Alessio; Laloui, Lyesse

2018-05-01

This paper investigates the anisotropic hydro-mechanical behaviour of Opalinus Clay shale, the host material currently being considered for the construction of a nuclear waste repository in Switzerland. Consolidated and drained triaxial tests on Opalinus Clay from the Mont Terri URL have been conducted in order to derive information on its strength and stiffness properties. Opalinus Clay specimens were tested both parallel to bedding (P-specimens) and perpendicular to bedding (S-specimens). The considered effective confining stress range (from 2 to 12 MPa) has been selected in order to reproduce possible in situ stress conditions for the repository. In this work, particular attention has been paid to the experimental procedure in order to ensure consolidated conditions and avoid generation of unwanted excess pore water pressure during drained shearing. The Skempton B parameter has been determined for all the tested specimens in order to ensure saturation. Both single-stage and multistage triaxial testing procedures were adopted in the experimental campaign. The results of the triaxial tests highlight an anisotropic elastic response of Opalinus Clay: S-specimens present a more compliant behaviour than P-specimens. The values of the Young modulus are found to increase with the increase in mean effective stress. The analysis of the peak and ultimate shear strength results reveals that the material behaves in a similar manner regardless of the considered direction of loading (P and S directions) with respect to the bedding orientation. Peak and ultimate failure envelopes for Opalinus Clay were derived for the investigated stress range.

Coupling Effects of Heat and Moisture on the Saturation Processes of Buffer Material in a Deep Geological Repository

NASA Astrophysics Data System (ADS)

Huang, Wei-Hsing

2017-04-01

Clay barrier plays a major role for the isolation of radioactive wastes in a underground repository. This paper investigates the resaturation behavior of clay barrier, with emphasis on the coupling effects of heat and moisture of buffer material in the near-field of a repository during groundwater intrusion processes. A locally available clay named "Zhisin clay" and a standard bentotine material were adopted in the laboratory program. Water uptake tests were conducted on clay specimens compacted at various densities to simulate the intrusion of groundwater into the buffer material. Soil suction of clay specimens was measured by psychrometers embedded in clay specimens and by vapor equilibrium technique conducted at varying temperatures. Using the soil water characteristic curve, an integration scheme was introduced to estimate the hydraulic conductivity of unsaturated clay. The finite element program ABAQUS was then employed to carry out the numerical simulation of the saturation process in the near field of a repository. Results of the numerical simulation were validated using the degree of saturation profile obtained from the water uptake tests on Zhisin clay. The numerical scheme was then extended to establish a model simulating the resaturation process after the closure of a repository. It was found that, due to the variation in suction and thermal conductivity with temperature of clay barrier material, the calculated temperature field shows a reduction as a result of incorporating the hydro-properties in the calculations.

Assessment of the Mechanical Properties of Sisal Fiber-Reinforced Silty Clay Using Triaxial Shear Tests

PubMed Central

Wu, Yankai; Li, Yanbin; Niu, Bin

2014-01-01

Fiber reinforcement is widely used in construction engineering to improve the mechanical properties of soil because it increases the soil's strength and improves the soil's mechanical properties. However, the mechanical properties of fiber-reinforced soils remain controversial. The present study investigated the mechanical properties of silty clay reinforced with discrete, randomly distributed sisal fibers using triaxial shear tests. The sisal fibers were cut to different lengths, randomly mixed with silty clay in varying percentages, and compacted to the maximum dry density at the optimum moisture content. The results indicate that with a fiber length of 10 mm and content of 1.0%, sisal fiber-reinforced silty clay is 20% stronger than nonreinforced silty clay. The fiber-reinforced silty clay exhibited crack fracture and surface shear fracture failure modes, implying that sisal fiber is a good earth reinforcement material with potential applications in civil engineering, dam foundation, roadbed engineering, and ground treatment. PMID:24982951

Dragon Skin - How It Changed Body Armor Testing in the United States Army

DTIC Science & Technology

2015-09-01

flat front surface for accurate and consistent measurement of depression depths. After the clay has been worked into the rigid frame, the clay backing...material will be simultaneously conditioned for use in filling depressions created by the drop testing and building up areas to fit non-planar body...clay consistency shall be such that a depression of [redacted] in depth is obtained when a [redacted] cylindrical steel mass (see Figure 4

Stabilization Of Marine Clay Using Biomass Silica-Rubber Chips Mixture

NASA Astrophysics Data System (ADS)

Marto, Aminaton; Ridzuan Jahidin, Mohammed; Aziz, Norazirah Abdul; Kasim, Fauziah; Zurairahetty Mohd. Yunus, Nor

2016-11-01

Marine clay is found widely along the coastal area and had caused expensive solutions in the construction of coastal highways. Hence, soil stabilization was suggested by some consultant to increase the strength of this soil in order to meet the highway construction requirement and also to achieve the specification for the development. Biomass Silica (BS), particularly the SH85 as a non-traditional stabilisation method, has been gaining more interest from the engineers recently. Rubber chips (RC), derived from waste rubber tyres, are considered ‘green’ element and had been used previously in some geotechnical engineering works. This paper presents the effect of using BS and RC as a mixture (BS-RC mixture), to increase the strength of marine clay for highway construction. Samples of marine clay, obtained from the West Coast Expressway project at Teluk Intan, Perak, were oven dried and grind to fine-grained sized. The marine clay was mixed with 9 % by weight proportion of BS- RC; that were 8%-l% and 7%-2%, respectively. For comparison purposes the result of BS-RC was compared to the result of stabilization by using 9% BS only. Laboratory tests were then carried out to determine the Atterberg limits and compaction characteristics of the untreated and treated marine clay. The Unconfined Compressive Strength (UCS) of the untreated and treated marine clays, compacted at the optimum moisture content was later obtained. The treated marine clay was tested at 0, 3 and 7 days curing periods. The results show that the Plasticity Index of BS-RC treated marine clay was lower than the untreated marine clay. From the UCS test results, it is shown that BS-RC mixtures had significantly improved the strength of marine clay. With the same percentage of 9% BS-RC, the increased of BS from 7% to 8% increased the UCS further to about six times more than untreated marine clay soils in 7 days curing period. The strength gained by using BS-RC at 8%-1% is slightly below the strength by using 9% BS only. From the experimental results, it is shown that BS, in the form of SH85, admixed with rubber chips could significantly improve the strength of marine clay soils.

Report on International Collaboration Involving the FE Heater and HG-A Tests at Mont Terri

DOE Office of Scientific and Technical Information (OSTI.GOV)

Houseworth, Jim; Rutqvist, Jonny; Asahina, Daisuke

Nuclear waste programs outside of the US have focused on different host rock types for geological disposal of high-level radioactive waste. Several countries, including France, Switzerland, Belgium, and Japan are exploring the possibility of waste disposal in shale and other clay-rich rock that fall within the general classification of argillaceous rock. This rock type is also of interest for the US program because the US has extensive sedimentary basins containing large deposits of argillaceous rock. LBNL, as part of the DOE-NE Used Fuel Disposition Campaign, is collaborating on some of the underground research laboratory (URL) activities at the Mont Terrimore » URL near Saint-Ursanne, Switzerland. The Mont Terri project, which began in 1995, has developed a URL at a depth of about 300 m in a stiff clay formation called the Opalinus Clay. Our current collaboration efforts include two test modeling activities for the FE heater test and the HG-A leak-off test. This report documents results concerning our current modeling of these field tests. The overall objectives of these activities include an improved understanding of and advanced relevant modeling capabilities for EDZ evolution in clay repositories and the associated coupled processes, and to develop a technical basis for the maximum allowable temperature for a clay repository.« less

Mars, clays and the origins of life

NASA Technical Reports Server (NTRS)

Hartman, Hyman

1989-01-01

To detect life in the Martian soil, tests were designed to look for respiration and photosynthesis. Both tests (labeled release, LR, and pyrolytic release, PR) for life in the Martian soils were positive. However, when the measurement for organic molecules in the soil of Mars was made, none were found. The interpretation given is that the inorganic constituents of the soil of Mars were responsible for these observations. The inorganic analysis of the soil was best fitted by a mixture of minerals: 60 to 80 percent clay, iron oxide, quartz, and soluble salts such as halite (NaCl). The minerals most successful in simulating the PR and LR experiments are iron-rich clays. There is a theory that considers clays as the first organisms capable of replication, mutation, and catalysis, and hence of evolving. Clays are formed when liquid water causes the weathering of rocks. The distribution of ions such as aluminum, magnesium, and iron play the role of bases in the DNA. The information was stored in the distribution of ions in the octahedral and tetrahedral molecules, but that they could, like RNA and DNA, replicate. When the clays replicated, each sheet of clay would be a template for a new sheet. The ion substitutions in one clay sheet would give rise to a complementary or similar pattern on the clay synthesized on its surface. It was theorized that it was on the surface of replicating iron-rich clays that carbon dioxide would be fixed in the light into organic acids such as formic or oxalic acid. If Mars had liquid water during a warm period in its past, clay formation would have been abundant. These clays would have replicated and evolved until the liquid water was removed due to cooling of Mars. It is entirely possible that the Viking mission detected life on Mars, but it was clay life that awaits the return of water to continue its evolution into life based on organic molecules.

Field Jet Erosion Tests on the Mississippi River Collocated Demonstration Section, Plaquemines Parish, Louisiana

DTIC Science & Technology

2015-06-01

ash/bed-ash blend treatment, and the second segment was constructed of Bonnet Carré clay treated with lime . In addition, a section of untreated clay...on the original levee was also tested. The field JET data showed that the clay treated with lime was categorized as resistant to very resistant. The...treatments reduced the erodibility of the soil. However, the field JET results showed that lime treatment performed better at reducing erosion than the

Ground penetrating radar imaging of cap rock, caliche and carbonate strata

USGS Publications Warehouse

Kruse, S.E.; Schneider, J.C.; Campagna, D.J.; Inman, J.A.; Hickey, T.D.

2000-01-01

Field experiments show ground penetrating radar (GPR) can be used to image shallow carbonate stratigraphy effectively in a variety of settings. In south Florida, the position and structure of cap rock cover on limestone can be an important control on surface water flow and vegetation, but larger scale outcrops (tens of meters) of cap rock are sparse. GPR mapping through south Florida prairie, cypress swamp and hardwood hammock resolves variations in thickness and structure of cap rock to ~3 m and holds the potential to test theories for cap rock-vegetation relationships. In other settings, carbonate strata are mapped to test models for the formation of local structural anomalies. A test of GPR imaging capabilities on an arid caliche (calcrete) horizon in southeastern Nevada shows depth penetration to ~2 m with resolution of the base of caliche. GPR profiling also succeeds in resolving more deeply buried (~5 m) limestone discontinuity surfaces that record subaerial exposure in south Florida. (C) 2000 Elsevier Science B.V. All rights reserved.Field experiments show ground penetrating radar (GPR) can be used to image shallow carbonate stratigraphy effectively in a variety of settings. In south Florida, the position and structure of cap rock cover on limestone can be an important control on surface water flow and vegetation, but larger scale outcrops (tens of meters) of cap rock are sparse. GPR mapping through south Florida prairie, cypress swamp and hardwood hammock resolves variations in thickness and structure of cap rock to approx. 3 m and holds the potential to test theories for cap rock-vegetation relationships. In other settings, carbonate strata are mapped to test models for the formation of local structural anomalies. A test of GPR imaging capabilities on an arid caliche (calcrete) horizon in southeastern Nevada shows depth penetration to approx. 2 m with resolution of the base of caliche. GPR profiling also succeeds in resolving more deeply buried (approx. 5 m) limestone discontinuity surfaces that record subaerial exposure in south Florida.

Aluminium - Cobalt-Pillared Clay for Dye Filtration Membrane

NASA Astrophysics Data System (ADS)

Darmawan, A.; Widiarsih

2018-04-01

The manufacture of membrane support from cobalt aluminium pillared clay has been conducted. This research was conducted by mixing a clay suspension with pillared solution prepared from the mixture of Co(NO3)2.6H2O and AlCl3.6H2O. The molar ratio between Al and Co was 75:25 and the ratio of [OH-]/[metal] was 2. The clay suspension was stirred for 24 hours at room temperature, filtered and dried. The dried clay was then calcined at 200°C, 300°C and 400°C with a ramp rate of 2°C/min. Aluminium-cobalt-pillared clay was then characterized by XRD and GSA and moulded become a membrane support for subsequent tests on dye filtration. The XRD analysis showed that basal spacing (d 001) value of aluminium cobalt was 19.49 Å, which was higher than the natural clay of 15.08Å however, the basal spacing decreased with increasing calcination temperature. The result of the GSA analysis showed that the pore diameter of the aluminium cobalt pillared clay membrane was almost the same as that of natural clay that were 34.5Å and 34.2Å, respectively. Nevertheless, the pillared clay has a more uniform pore size distribution. The results of methylene blue filtration measurements demonstrated that the membrane filter support could well which shown by a clear filtrate at all concentrations tested. The value of rejection and flux decreased with the increasing concentration of methylene blue. The values of dye rejection and water flux reached 99.89% and 5. 80 x 10-6 kg min-1, respectively but they decreased with increasing concentration of methylene blue. The results of this study indicates that the aluminium-pillared clay cobalt could be used as membrane materials especially for ultrafiltration.

Creep and Sliding in Clay Slopes: Mutual Effects of Interlayer Swelling and Ice Jacking.

DTIC Science & Technology

1983-04-24

calcite and feldspar constituents. Therefore a swelling clay with low diagenetic lithification (matrix forming) e fects. Therefore, the clay shows...were determined quantitatively (Tab. 2). The CEC depends mainly on the montmorillonite content and shows values up to 86 meq/lOOg, which Indicates...high montmorillonite clays. First freezing tests have been performed within a freezer. After freezing, three typical zones within the samples can be

488-4D ASH LANDFILL CLOSURE CAP HELP MODELING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phifer, M.

At the request of Area Completion Projects (ACP) in support of the 488-4D Landfill closure, the Savannah River National Laboratory (SRNL) has performed Hydrologic Evaluation of Landfill Performance (HELP) modeling of the planned 488-4D Ash Landfill closure cap to ensure that the South Carolina Department of Health and Environmental Control (SCDHEC) limit of no more than 12 inches of head on top of the barrier layer (saturated hydraulic conductivity of no more than 1.0E-05 cm/s) in association with a 25-year, 24-hour storm event is not projected to be exceeded. Based upon Weber 1998 a 25-year, 24-hour storm event at themore » Savannah River Site (SRS) is 6.1 inches. The results of the HELP modeling indicate that the greatest peak daily head on top of the barrier layer (i.e. geosynthetic clay liner (GCL) or high density polyethylene (HDPE) geomembrane) for any of the runs made was 0.079 inches associated with a peak daily precipitation of 6.16 inches. This is well below the SCDHEC limit of 12 inches.« less

[Mechanisms of removing red tide organisms by organo-clays].

PubMed

Cao, Xi-Hua; Song, Xiu-Xian; Yu, Zhi-Ming; Wang, Kui

2006-08-01

We tested the influence of the preparation conditions of the quaternary ammonium compounds (QACs) modified clays on their capacities to remove red tide organisms, then discussed the mechanisms of the organo-clays removing red tide organisms. Hexadecyltrimethylammonium (HDTMA) improved the capacity of clays to flocculate red tide algae, and the HDTMA in metastable state enhanced the toxicity of the clay complexes to algae. The capacities of the organo-clays correlated with the toxicity and the adsorbed amount of the QACs used in clays modification, but as the incubation time was prolonged the stability of the organo-clays was improved and the algal removal efficiencies of the clay complexes decreased. When the adsorbed HDTMA was arranged in different clays in which the spatial resistance was different, there was more HDTMA in metastable state in the three-layer montmorillonite. Because of the homo-ion effect the bivalent or trivalent metal ions induced more HDTMA in metastable state and the corresponding organo-clays had high capacities to remove red tide organisms. When the reaction temperature was 60 degrees C the adsorbed HDTMA was easily arranged on cation exchange sites, if the temperature rose or fell the metastable HDTMA would increase so that the capacity of the clays was improved.

Micromechanical Properties of Nanostructured Clay-Oxide Multilayers Synthesized by Layer-by-Layer Self-Assembly.

PubMed

Hou, Dongwei; Zhang, Guoping; Pant, Rohit Raj; Wei, Zhongxin; Shen, Shuilong

2016-11-08

Clay-based nanostructured multilayers, such as clay-polymer multilayers and clay-oxide multilayers, have attracted growing attention owing to their remarkable mechanical properties and promising application in various fields. In this paper, synthesis of a new kind of nanostructured clay-oxide multilayers by layer-by-layer self-assembly was explored. Nano-mechanical characterization of 18 clay-based multilayer samples, prepared under as-deposited (i.e., air-dried) and annealing conditions at 400 °C/600 °C with different precursor cations and multilayer structure, were carried out using nanoindentation testing, atomic force microscopy (AFM), and X-ray diffraction (XRD). The influencing factors, including as-deposited and annealing conditions and clay concentrations on the mechanical properties were analyzed. Results show that all of the multilayers exhibit high bonding strength between interlayers. Higher modulus and hardness of clay-based multilayers were obtained with lower clay concentrations than that with higher clay concentrations. Different relationships between the modulus and hardness and the annealing temperature exist for a specific type of clay-oxide multilayer. This work offers the basic and essential knowledge on design of clay-based nanostructured multilayers by layer-by-layer self-assembly.

Numerical simulations of sand production in interbedded hydrate-bearing sediments during depressurization

USGS Publications Warehouse

Uchida, Shun; Lin, Jeen-Shang; Myshakin, Evgeniy; Seol, Yongkoo; Collett, Timothy S.; Boswell, Ray

2017-01-01

Geomechanical behavior of hydrate-bearing sediments during gas production is complex, involving changes in hydrate-dependent mechanical properties. When interbedded clay layers are present, the complexity is more pronounced because hydrate dissociation tends to occur preferentially in the sediments adjacent to the clay layers due to clay layers acting as a heat source. This would potentially lead to shearing deformation along the sand/clay contacts and may contribute to solid migration, which hindered past field-scale gas production tests. This paper presents a near-wellbore simulation of sand/clay interbedded hydrate-bearing sediments that have been subjected to depressurization and discusses the effect of clay layers on sand production.

Sorption of Cesium on smectite-rich clays from the Bohemian Massif (Czech Republic) and their mixtures with sand.

PubMed

Vejsada, J; Jelínek, E; Randa, Z; Hradil, D; Prikryl, R

2005-01-01

Sorption is an important process for the transport of radionuclides through backfill materials in a radioactive waste underground repository. Within this study, sorption of Cs on selected Czech clay materials and their mixtures with sand was investigated by batch tests. The experiments were performed under oxic conditions at 25 degrees C. Synthetic groundwater as a liquid phase and unconditioned clays (as they were provided by their producer) were used to reach the natural conditions as close as possible. Distribution ratios (Rds) of Cs for all selected clays rise with increase of the clay fraction in clay/sand mixtures in agreement with previous works studying sorption behaviour of such mixtures. The rise of Rds is from 10(2) cm3 g(-1) for mixtures with 80% of sand to 10(3) cm3 g(-1) for pure clays. There are significant differences between natural and technologically modified clays.

Assessing landslide potential on coastal bluffs near Mukilteo, Washington—Geologic site characterization for hydrologic monitoring

USGS Publications Warehouse

Mirus, Benjamin B.; Smith, Joel B.; Benjamin Stark,; York Lewis,; Abigail Michel,; Baum, Rex L.

2016-07-01

During the summer 2015, the U.S. Geological Survey collected geologic and geotechnical data for two sites on coastal bluffs along the eastern shore of Puget Sound, Washington. The U.S. Geological Survey also installed hydrologic instrumentation at the sites and collected specimens for laboratory testing. The two sites are located on City of Mukilteo open-space land and are about 0.6 kilometers apart. The bluffs at each site are approximately 42 meters high, and rise steeply from the shoreline with 32–35° slopes. The more northerly of the two sites occupies an active landslide and is mostly unvegetated. The other site is forested, and although stable during the preparation of this report, shows evidence of historical and potential landslide activity. The slopes of the bluffs at both sites are mantled by a thin, nonuniform colluvium underlain by clay-rich glacial deposits and tills of the Whidbey Formation or Double Bluff Drift. Till consisting of sand, gravel, and cobbles caps the bluffs and rests on finer grained glacial deposits of sand, silt, and clay. These types of different glacial deposits are dense, vertically fractured, and generally have low permeability, but field observations indicate that locally the deposits are sufficiently permeable to allow lateral flow of water along fractures and subhorizontal boundaries between deposits of different texture. Laboratory tests indicate that many of the deposits are highly plastic, with low hydraulic conductivity, and moderate shear strength. Steep slopes combined with the strength and hydraulic characteristics of the deposits leave the bluffs prone to slope instability, particularly during the wet season when infiltrating rainfall changes moisture content, pore-water pressure, and effective stress within the hillslope. The instrumentation was designed to primarily observe rainfall variability and hydrologic changes in the subsurface that can affect stability of the bluffs, and also to compare the hydrologic response between areas where previous landslides have disturbed vegetation and areas where the bluff is apparently more stable and well vegetated.

Volcanic geothermal system in the Main Ethiopian Rift: insights from 3D MT finite-element inversion and other exploration methods

NASA Astrophysics Data System (ADS)

Samrock, F.; Grayver, A.; Eysteinsson, H.; Saar, M. O.

2017-12-01

In search for geothermal resources, especially in exploration for high-enthalpy systems found in regions with active volcanism, the magnetotelluric (MT) method has proven to be an efficient tool. Electrical conductivity of the subsurface, imaged by MT, is used for detecting layers of electrically highly conductive clays which form around the surrounding strata of hot circulating fluids and for delineating magmatic heat sources such as zones with partial melting. We present a case study using a novel 3-D inverse solver, based on adaptive local mesh refinement techniques, applied to decoupled forward and inverse mesh parameterizations. The flexible meshing allows accurate representation of surface topography, while keeping computational costs at a reasonable level. The MT data set we analyze was measured at 112 sites, covering an area of 18 by 11 km at a geothermal prospect in the Main Ethiopian Rift. For inverse modelling, we tested a series of different settings to ensure that the recovered structures are supported by the data. Specifically, we tested different starting models, regularization functionals, sets of transfer functions, with and without inclusion of topography. Several robust subsurface structures were revealed. These are prominent features of a high-enthalpy geothermal system: A highly conductive shallow clay cap occurs in an area with high fumarolic activity, and is underlain by a more resistive zone, which is commonly interpreted as a propylitic reservoir and is the main geothermal target for drilling. An interesting discovery is the existence of a channel-like conductor connecting the geothermal field at the surface with an off-rift conductive zone, whose existence was proposed earlier as being related to an off-rift volcanic belt along the western shoulder of the Main Ethiopian Rift. The electrical conductivity model is interpreted together with results from other geoscientific studies and outcomes from satellite remote sensing techniques.

Effects of selenizing angelica polysaccharide and selenizing garlic polysaccharide on immune function of murine peritoneal macrophage.

PubMed

Gao, Zhenzhen; Liu, Kuanhui; Tian, Weijun; Wang, Hongchao; Liu, Zhenguang; Li, Youying; Li, Entao; Liu, Cui; Li, Xiuping; Hou, Ranran; Yue, Chanjuan; Wang, Deyun; Hu, Yuanliang

2015-07-01

The effects of two selenizing polysaccharides (sCAP2 and sGPS6) on immune function of murine peritoneal macrophages taking two non-selenizing polysaccharides (CAP and GPS) and modifier Na2SeO3 as control. In vitro test, the changes of selenizing polysaccharides, non-selenizing polysaccharides and Na2SeO3 on murine macrophages function were evaluated by phagocytosis and nitric oxide (NO) secretion tests. In vivo test, the mice were injected respectively with 0.2, 0.4 and 0.6 mg of sCAP2, sGPS6, CAP and GPS, or Na2SeO3 80 μg or normal saline 0.4 mL. The peritoneal macrophages were collected and cultured to determine the contents of TNF-α, IL-6 and IL-10 in supernatants by enzyme-linked immunosorbent assay. The results showed that sCAP2 and sGPS6 could significantly promote the phagocytosis and secretion of NO and three cytokines of macrophages in comparison with CAP and GPS. sCAP2 possessed the strongest activity. This indicates that selenylation modification can further improve the immune-enhancing activity of polysaccharide, and sCAP2 could be as a new immunopotentiator. Copyright © 2015 Elsevier B.V. All rights reserved.

Clay Improvement with Burned Olive Waste Ash

PubMed Central

Mutman, Utkan

2013-01-01

Olive oil is concentrated in the Mediterranean basin countries. Since the olive oil industries are incriminated for a high quantity of pollution, it has become imperative to solve this problem by developing optimized systems for the treatment of olive oil wastes. This study proposes a solution to the problem. Burned olive waste ash is evaluated for using it as clay stabilizer. In a laboratory, bentonite clay is used to improve olive waste ash. Before the laboratory, the olive waste is burned at 550°C in the high temperature oven. The burned olive waste ash was added to bentonite clay with increasing 1% by weight from 1% to 10%. The study consisted of the following tests on samples treated with burned olive waste ash: Atterberg Limits, Standard Proctor Density, and Unconfined Compressive Strength Tests. The test results show promise for this material to be used as stabilizer and to solve many of the problems associated with its accumulation. PMID:23766671

Removal of clay by stingless bees: load size and moisture selection.

PubMed

Costa-Pereira, Raul

2014-09-01

Some organisms disperse energy, associated with the transportation of resource, which is not necessarily food. Stingless bees of Central Amazonia (Melipona flavolineata and M. lateralis) collect clay in banks along streams for nest building. The moisture of the clay varies along the bank, and bees collect clay from specific location, indicating that there is some sort of preference regarding their selection. This study aims at identifying: if larger bees carry more clay; if there is a preference for moisture of substrates; and if bees are less efficient accumulating and transporting clay when it is wet. In order to do so, I measured the size of the bees and of the pellets of clay found in the corbicula. I set up a field experiment to test substrate preferences. The amount of clay transported, increased exponentially in accordance to the size of the bee, and the preferred substrate was the driest clay. The amount and the efficiency of removal of clay were not affected by the moisture of the substrate. Despite the wet clay being denser, it does not reduce the efficiency of exploitation of the resource, but suggests that bees spend more energy to carry the same quantity of wet clay, which may be the underlying mechanism explaining their preference for removing drier clay.

The Clinician-Administered PTSD Scale for DSM-5 (CAPS-5): Development and initial psychometric evaluation in military veterans.

PubMed

Weathers, Frank W; Bovin, Michelle J; Lee, Daniel J; Sloan, Denise M; Schnurr, Paula P; Kaloupek, Danny G; Keane, Terence M; Marx, Brian P

2018-03-01

The Clinician-Administered PTSD Scale (CAPS) is an extensively validated and widely used structured diagnostic interview for posttraumatic stress disorder (PTSD). The CAPS was recently revised to correspond with PTSD criteria in the fifth edition of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5; American Psychiatric Association, 2013). This article describes the development of the CAPS for DSM-5 (CAPS-5) and presents the results of an initial psychometric evaluation of CAPS-5 scores in 2 samples of military veterans (Ns = 165 and 207). CAPS-5 diagnosis demonstrated strong interrater reliability (к = .78 to 1.00, depending on the scoring rule) and test-retest reliability (к = .83), as well as strong correspondence with a diagnosis based on the CAPS for DSM-IV (CAPS-IV; к = .84 when optimally calibrated). CAPS-5 total severity score demonstrated high internal consistency (α = .88) and interrater reliability (ICC = .91) and good test-retest reliability (ICC = .78). It also demonstrated good convergent validity with total severity score on the CAPS-IV (r = .83) and PTSD Checklist for DSM-5 (r = .66) and good discriminant validity with measures of anxiety, depression, somatization, functional impairment, psychopathy, and alcohol abuse (rs = .02 to .54). Overall, these results indicate that the CAPS-5 is a psychometrically sound measure of DSM-5 PTSD diagnosis and symptom severity. Importantly, the CAPS-5 strongly corresponds with the CAPS-IV, which suggests that backward compatibility with the CAPS-IV was maintained and that the CAPS-5 provides continuity in evidence-based assessment of PTSD in the transition from DSM-IV to DSM-5 criteria. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Comparative study of two precision overdenture attachment designs.

PubMed

Cohen, B I; Pagnillo, M; Condos, S; Deutsch, A S

1996-08-01

In this study two precision overdenture attachment designs were tested for retention--a nylon overdenture cap system and a new cap and keeper system. The new cap and keeper system was designed to reduce the time involved in replacing a cap worn by the conditions of the oral environment. Six groups were tested at two different angles and retentive failure was examined at two different angles (26 and 0 degrees). Failure was measured in pounds with a force gauge over a 2000 pull cycle. The amount of force required to remove caps for two overdenture caps and a replaced cap for the metal keeper system was determined. Two dependent variables were absolute force and relative force. Repeated measures analysis of variance (RMANOVA) was used to compare the between-subjects effects of cap and angle, and the within-subjects effect of pull. The results indicated a significant difference between cap types (p < 0.0001) with respect to the relative force required to remove the cap. There was no effect of angle. For absolute force, RMANOVA revealed a highly significant interaction between pull and cap (p < 0.0001). Thus, the way that force changed over pulls depended on which cap was used (no effect of angle). For relative force, RMANOVA revealed no interaction between pull and cap, but there was a main effect of cap type (p < 0.0001) (no effect of angle). The nylon cap design required less force for removal but showed more consistency in the force required over the course of the 2000 pulls when compared with the keeper with cap insert. The results obtained in this study were consistent with similar studies in literature.

Termites utilise clay to build structural supports and so increase foraging resources.

PubMed

Oberst, Sebastian; Lai, Joseph C S; Evans, Theodore A

2016-02-08

Many termite species use clay to build foraging galleries and mound-nests. In some cases clay is placed within excavations of their wooden food, such as living trees or timber in buildings; however the purpose for this clay is unclear. We tested the hypotheses that termites can identify load bearing wood, and that they use clay to provide mechanical support of the load and thus allow them to eat the wood. In field and laboratory experiments, we show that the lower termite Coptotermes acinaciformis, the most basal species to build a mound-nest, can distinguish unloaded from loaded wood, and use clay differently when eating each type. The termites target unloaded wood preferentially, and use thin clay sheeting to camouflage themselves while eating the unloaded wood. The termites attack loaded wood secondarily, and build thick, load-bearing clay walls when they do. The termites add clay and build thicker walls as the load-bearing wood is consumed. The use of clay to support wood under load unlocks otherwise unavailable food resources. This behaviour may represent an evolutionary step from foraging behaviour to nest building in lower termites.

Burden of vaccine-preventable pneumococcal disease in hospitalized adults: A Canadian Immunization Research Network (CIRN) Serious Outcomes Surveillance (SOS) network study.

PubMed

LeBlanc, Jason J; ElSherif, May; Ye, Lingyun; MacKinnon-Cameron, Donna; Li, Li; Ambrose, Ardith; Hatchette, Todd F; Lang, Amanda L; Gillis, Hayley; Martin, Irene; Andrew, Melissa K; Boivin, Guy; Bowie, William; Green, Karen; Johnstone, Jennie; Loeb, Mark; McCarthy, Anne; McGeer, Allison; Moraca, Sanela; Semret, Makeda; Stiver, Grant; Trottier, Sylvie; Valiquette, Louis; Webster, Duncan; McNeil, Shelly A

2017-06-22

Pneumococcal community acquired pneumonia (CAP Spn ) and invasive pneumococcal disease (IPD) cause significant morbidity and mortality worldwide. Although childhood immunization programs have reduced the overall burden of pneumococcal disease, there is insufficient data in Canada to inform immunization policy in immunocompetent adults. This study aimed to describe clinical outcomes of pneumococcal disease in hospitalized Canadian adults, and determine the proportion of cases caused by vaccine-preventable serotypes. Active surveillance for CAP Spn and IPD in hospitalized adults was performed in hospitals across five Canadian provinces from December 2010 to 2013. CAP Spn were identified using sputum culture, blood culture, a commercial pan-pneumococcal urine antigen detection (UAD), or a serotype-specific UAD. The serotype distribution was characterized using Quellung reaction, and PCR-based serotyping on cultured isolates, or using a 13-valent pneumococcal conjugate vaccine (PCV13) serotype-specific UAD assay. In total, 4769 all-cause CAP cases and 81 cases of IPD (non-CAP) were identified. Of the 4769 all-cause CAP cases, a laboratory test for S. pneumoniae was performed in 3851, identifying 14.3% as CAP Spn . Of CAP cases among whom all four diagnostic test were performed, S. pneumoniae was identified in 23.2% (144/621). CAP Spn cases increased with age and the disease burden of illness was evident in terms of requirement for mechanical ventilation, intensive care unit admission, and 30-day mortality. Of serotypeable CAP Spn or IPD results, predominance for serotypes 3, 7F, 19A, and 22F was observed. The proportion of hospitalized CAP cases caused by a PCV13-type S. pneumoniae ranged between 7.0% and 14.8% among cases with at least one test for S. pneumoniae performed or in whom all four diagnostic tests were performed, respectively. Overall, vaccine-preventable pneumococcal CAP and IPD were shown to be significant causes of morbidity and mortality in hospitalized Canadian adults in the three years following infant PCV13 immunization programs in Canada. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

The Cobas AmpliPrep/Cobas TaqMan HCV test, version 2.0, real-time PCR assay accurately quantifies hepatitis C virus genotype 4 RNA.

PubMed

Chevaliez, Stéphane; Bouvier-Alias, Magali; Rodriguez, Christophe; Soulier, Alexandre; Poveda, Jean-Dominique; Pawlotsky, Jean-Michel

2013-04-01

Accurate hepatitis C virus (HCV) RNA quantification is mandatory for the management of chronic hepatitis C therapy. The first-generation Cobas AmpliPrep/Cobas TaqMan HCV test (CAP/CTM HCV) underestimated HCV RNA levels by >1-log10 international units/ml in a number of patients infected with HCV genotype 4 and occasionally failed to detect it. The aim of this study was to evaluate the ability of the Cobas AmpliPrep/Cobas TaqMan HCV test, version 2.0 (CAP/CTM HCV v2.0), to accurately quantify HCV RNA in a large series of patients infected with different subtypes of HCV genotype 4. Group A comprised 122 patients with chronic HCV genotype 4 infection, and group B comprised 4 patients with HCV genotype 4 in whom HCV RNA was undetectable using the CAP/CTM HCV. Each specimen was tested with the third-generation branched DNA (bDNA) assay, CAP/CTM HCV, and CAP/CTM HCV v2.0. The HCV RNA level was lower in CAP/CTM HCV than in bDNA in 76.2% of cases, regardless of the HCV genotype 4 subtype. In contrast, the correlation between bDNA and CAP/CTM HCV v2.0 values was excellent. CAP/CTM HCV v2.0 accurately quantified HCV RNA levels in the presence of an A-to-T substitution at position 165 alone or combined with a G-to-A substitution at position 145 of the 5' untranslated region of HCV genome. In conclusion, CAP/CTM HCV v2.0 accurately quantifies HCV RNA in genotype 4 clinical specimens, regardless of the subtype, and can be confidently used in clinical trials and clinical practice with this genotype.

Automated method for determining Instron Residual Seal Force of glass vial/rubber closure systems.

PubMed

Ludwig, J D; Nolan, P D; Davis, C W

1993-01-01

Instron Residual Seal Force (IRSF) of glass vial/rubber closure systems was determined using an Instron 4501 Materials Testing System. Computer programs were written to process raw data and calculate IRSF values. Preliminary experiments indicated both the appearance of the stress-deformation curves and precision of the derived IRSF values were dependent on the internal dimensions and top surface geometry of the cap anvil. Therefore, a series of five cap anvils varying in shape and dimensions were machined to optimize performance and precision. Vials capped with West 4416/50 PURCOAT button closures or Helvoet compound 6207 lyophilization closures were tested with each cap anvil. Cap anvils with spherical top surfaces and narrow internal dimensions produced more precise results and more uniform stress-deformation curves than cap anvils with flat top surfaces and wider internal dimensions.

Degradation of chloramphenicol by potassium ferrate (VI) oxidation: kinetics and products.

PubMed

Zhou, Jia-Heng; Chen, Kai-Bo; Hong, Qian-Kun; Zeng, Fan-Cheng; Wang, Hong-Yu

2017-04-01

The oxidation of chloramphenicol (CAP) by potassium ferrate (VI) in test solution was studied in this paper. A series of jar tests were performed at bench scale with pH of 5-9 and molar ratio [VI/CAP] of 16.3:1-81.6:1. Results showed that raising VI dose could improve the treatment performance and the influence of solution pH was significant. VI is more reactive in neutral conditions, presenting the highest removal efficiency of CAP. The rate law for the oxidation of CAP by VI was first order with respect to each reactant, yielding an overall second-order reaction. Furthermore, five oxidation products were observed during CAP oxidation by VI. Results revealed that VI attacked the amide group of CAP, leading to the cleavage of the group, while benzene ring remained intact.

The effect of clay nanoparticleon the retention and attack of drywood termite (Cryptotermes cynocephalus Light).

NASA Astrophysics Data System (ADS)

Alex, T.; Winarni, B.; Kusuma, I. W.; Arung, E. T.; Budiarso, E.

2018-04-01

The aplication of clay nanoparticles as wood preservative was intended to examine its resistant to infestation of drywood termite (C. cynocephalusLight). Loam was crushed into small pieces as clay nanoparticles, which was used as wood preservative that was soluble in water. The material was dissolved with water in a given concentration and put it into anggerung (Trema orientalis), white meranti (Shorea bracteolata) and sengon (Paraseriehthes falcataria) by full cell method or impregnation. The tested samples were preserved by clay nanoparticles at the air pressure 60 psi for 2 hours and then furnace-dried, and tested by infestation of drywood termites. Results of the research showed that mortality of the drywood termites on those three preserved woods with clay nanoparticles by concentration of 2.5% and 5%, which reached 96.4% and 100% on average, respectively, in comparison without preservation by average mortality value was 27.4%. The highest retention of clay nanoparticle was 24.89 kg.m3 was obtained by concentration of 5% for white merantiand the lowest was 9.32 kg.m3 by concentration of 2.5% for anggerung. The application of clay nanoparticle as effective wood preservative against the infestation of drywood termite by concentration of 5% has been proven by mortality 100%.

Field Performance of A Compacted Clay Landfill Final cover At A Humid Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albright, William H.; Benson, Craig H.; Gee, Glendon W.

A study was conducted in southern Georgia, USA to evaluate how the hydraulic properties of the compacted clay barrier layer in a landfill final cover changed over a 4-yr service life. The cover was part of a test section constructed in a large drainage lysimeter that allowed CE Database subject headings: landfill, hydrogeology, compacted soils, lysimeters, desiccation continuous monitoring of the water balance. Patterns in the drainage (i.e., flow from the bottom of the cover) record suggest that preferential flow paths developed in the clay barrier soon after construction, apparently in response to desiccation cracking. After four years, the claymore » barrier was excavated and examined for changes in soil structure and hydraulic conductivity. Tests were conducted in situ with a sealed double-ring infiltrometer and two-stage borehole permeameters and in the laboratory on hand-carved blocks taken during construction and after four years of service. The in situ and laboratory tests indicated that the hydraulic conductivity increased approximately three orders of magnitude (from ? 10-7 to ? 10-4 cm s-1) during the service life. A dye tracer test and soil structure analysis showed that extensive cracking and root development occurred throughout the entire depth of the barrier layer. Laboratory tests on undisturbed specimens of the clay barrier indicated that the hydraulic conductivity of damaged clay barriers can be under-estimated significantly if small specimens (e.g., tube samples) are used for hydraulic conductivity assessment. The findings also indicate that clay barriers must be protected from desiccation and root intrusion if they are expected to function as intended, even at sites in warm, humid locations.« less

Anatomical Knowledge Gain through a Clay-Modeling Exercise Compared to Live and Video Observations

ERIC Educational Resources Information Center

Kooloos, Jan G. M.; Schepens-Franke, Annelieke N.; Bergman, Esther M.; Donders, Rogier A. R. T.; Vorstenbosch, Marc A. T. M.

2014-01-01

Clay modeling is increasingly used as a teaching method other than dissection. The haptic experience during clay modeling is supposed to correspond to the learning effect of manipulations during exercises in the dissection room involving tissues and organs. We questioned this assumption in two pretest-post-test experiments. In these experiments,…

Geotechnical characterization of mined clay from Appalachian Ohio: challenges and implications for the clay mining industry.

PubMed

Moran, Anthony R; Hettiarachchi, Hiroshan

2011-07-01

Clayey soil found in coal mines in Appalachian Ohio is often sold to landfills for constructing Recompacted Soil Liners (RSL) in landfills. Since clayey soils possess low hydraulic conductivity, the suitability of mined clay for RSL in Ohio is first assessed by determining its clay content. When soil samples are tested in a laboratory, the same engineering properties are typically expected for the soils originated from the same source, provided that the testing techniques applied are standard, but mined clay from Appalachian Ohio has shown drastic differences in particle size distribution depending on the sampling and/or laboratory processing methods. Sometimes more than a 10 percent decrease in the clay content is observed in the samples collected at the stockpiles, compared to those collected through reverse circulation drilling. This discrepancy poses a challenge to geotechnical engineers who work on the prequalification process of RSL material as it can result in misleading estimates of the hydraulic conductivity of the samples. This paper describes a laboratory investigation conducted on mined clay from Appalachian Ohio to determine how and why the standard sampling and/or processing methods can affect the grain-size distributions. The variation in the clay content was determined to be due to heavy concentrations of shale fragments in the clayey soils. It was also concluded that, in order to obtain reliable grain size distributions from the samples collected at a stockpile of mined clay, the material needs to be processed using a soil grinder. Otherwise, the samples should be collected through drilling.

Geotechnical Characterization of Mined Clay from Appalachian Ohio: Challenges and Implications for the Clay Mining Industry

PubMed Central

Moran, Anthony R.; Hettiarachchi, Hiroshan

2011-01-01

Clayey soil found in coal mines in Appalachian Ohio is often sold to landfills for constructing Recompacted Soil Liners (RSL) in landfills. Since clayey soils possess low hydraulic conductivity, the suitability of mined clay for RSL in Ohio is first assessed by determining its clay content. When soil samples are tested in a laboratory, the same engineering properties are typically expected for the soils originated from the same source, provided that the testing techniques applied are standard, but mined clay from Appalachian Ohio has shown drastic differences in particle size distribution depending on the sampling and/or laboratory processing methods. Sometimes more than a 10 percent decrease in the clay content is observed in the samples collected at the stockpiles, compared to those collected through reverse circulation drilling. This discrepancy poses a challenge to geotechnical engineers who work on the prequalification process of RSL material as it can result in misleading estimates of the hydraulic conductivity of the samples. This paper describes a laboratory investigation conducted on mined clay from Appalachian Ohio to determine how and why the standard sampling and/or processing methods can affect the grain-size distributions. The variation in the clay content was determined to be due to heavy concentrations of shale fragments in the clayey soils. It was also concluded that, in order to obtain reliable grain size distributions from the samples collected at a stockpile of mined clay, the material needs to be processed using a soil grinder. Otherwise, the samples should be collected through drilling. PMID:21845150

Determination of chloramphenicol residues in commercial chicken eggs in the Federal Capital Territory, Abuja, Nigeria.

PubMed

Mbodi, Felix E; Nguku, P; Okolocha, E; Kabir, J

2014-01-01

The use of antibiotics in poultry can result in residues in eggs. The joint FAO/WHO committee recommended banning the use of chloramphenicol (CAP) in food animals due to its public health hazards of aplastic anaemia, leukaemia, allergy, antibacterial resistance and carcinogenicity. This paper determines the prevalence of CAP residues in chicken eggs and assesses the usage and awareness of its ban amongst poultry farmers in the Federal Capital Territory (FCT), Abuja, Nigeria. A cross-sectional survey of registered poultry farmers in FCT was conducted using questionnaires to determine CAP administration in poultry and awareness of its ban. Pooled egg samples were collected from each poultry farm surveyed and from randomly sampled government-owned markets in FCT. Source of eggs by state were identified by the marketer at the time of collection. Samples were analysed using an enzyme-linked immunosorbent assay (ELISA) technique for the presence of CAP, and prevalence was determined. Of 288 total pooled samples collected, 257 (89.2%) were from the markets and 31 (10.8%) were from poultry farms. A total of 20 (7%) pooled egg samples tested CAP-positive; market eggs originated from 15 (41%) states of the country. Of the market eggs, 16 (6.2%) pooled samples tested positive. Of eggs from poultry farms, four (12.9%) tested positive. Mean CAP concentrations in the positive samples ranged from 0.49 to 1.17 µg kg(-1) (parts per billion). CAP use amongst poultry farmers in FCT was 75.5%; awareness of the CAP ban was 26.3%. Though 66% of veterinarians were unaware of a CAP ban, they were more likely to be aware than other poultry farmers (odds ratio (OR) = 1.4). Farm managers who use CAP were more likely to be aware of CAP ban than the farm managers not using CAP (OR = 5.5; p = 0.04). Establishing a drug residue surveillance and control program and enforcement of CAP legislation/regulation is needful to educate and prohibit the widespread CAP use amongst Nigerian poultry farmers.

Geological and technological characterization of the Late Jurassic-Early Cretaceous clay deposits (Jebel Ammar, northeastern Tunisia) for ceramic industry

NASA Astrophysics Data System (ADS)

Ben M'barek-Jemaï, Moufida; Sdiri, Ali; Ben Salah, Imed; Ben Aissa, Lassaad; Bouaziz, Samir; Duplay, Joelle

2017-05-01

Late Jurassic-Lower Cretaceous clays of the Jebel Ammar study site were used as raw materials for potential applications in ceramic industry. Physico-chemical characterization of the collected samples was performed using atomic absorption spectroscopy, X-ray diffraction, thermogravimetry and dilatometry (Bugot's curve). Geotechnical study was also undertaken by the assessment of plasticity and liquidity limits. It was found that high concentrations of silica, alumina with SiO2/Al2O3 ratio characterized the studied clays; its high amounts of CaO and Fe2O3 in the Late Jurassic clays indicated their calcareous nature. In addition, technological tests indicated moderate to low plasticity values for the Late Jurassic and Lower Cretaceous clays, respectively. Clay fraction (<2 μm) reached 50% of the natural clay in some cases. Mineralogical analysis showed that Jurassic clays were dominated by smectite, illite and kaolinite, as clay mineral species; calcite was the main associated mineral. Lower Cretaceous clays were mainly composed of abundant illite accompanied by well-crystallized smectite and kaolinite. Kaolinite gradually increased upwards, reaching 70% of the total clay fraction (i.e. <2 μm). Quartz, calcite and feldspar were the main non-clay minerals. Based on these analyses, the clays meet technological requirements that would allow their use in the ceramic industry and for the manufacturing of ceramic tiles.

Evaluation of correlation between physical properties and ultrasonic pulse velocity of fired clay samples.

PubMed

Özkan, İlker; Yayla, Zeliha

2016-03-01

The aim of this study is to establish a correlation between physical properties and ultrasonic pulse velocity of clay samples fired at elevated temperatures. Brick-making clay and pottery clay were studied for this purpose. The physical properties of clay samples were assessed after firing pressed clay samples separately at temperatures of 850, 900, 950, 1000, 1050 and 1100 °C. A commercial ultrasonic testing instrument (Proceq Pundit Lab) was used to evaluate the ultrasonic pulse velocity measurements for each fired clay sample as a function of temperature. It was observed that there became a relationship between physical properties and ultrasonic pulse velocities of the samples. The results showed that in consequence of increasing densification of the samples, the differences between the ultrasonic pulse velocities were higher with increasing temperature. These findings may facilitate the use of ultrasonic pulse velocity for the estimation of physical properties of fired clay samples. Copyright © 2015 Elsevier B.V. All rights reserved.

Clay facial masks: physicochemical stability at different storage temperatures.

PubMed

Zague, Vivian; de Almeida Silva, Diego; Baby, André Rolim; Kaneko, Telma Mary; Velasco, Maria Valéria Robles

2007-01-01

Clay facial masks--formulations that contain a high percentage of solids dispersed in a liquid vehicle--have become of special interest due to specific properties presented by clays, such as particle size, cooling index, high adsorption capacity, and plasticity. Although most of the physicochemical properties of clay dispersions have been studied, specific aspects concerning the physicochemical stability of clay mask products remain unclear. This work aimed at investigating the accelerated physicochemical stability of clay mask formulations stored at different temperatures. Formulations were subjected to centrifuge testing and to thermal treatment for 15 days, during which temperature was varied from -5.0 degrees to 45.0 degrees C. The apparent viscosity and visual aspect (homogeneity) of all formulations were affected by temperature variation, whereas color, odor, and pH value remained unaltered. These results, besides the estimation of physicochemical stability under aging, can be useful in determining the best storage conditions for clay-based formulations.

California Bearing Ratio (CBR) test on stabilization of clay with lime addition

NASA Astrophysics Data System (ADS)

Hastuty, I. P.; Roesyanto; Limbong, M. N.; Oberlyn, S. J.

2018-02-01

Clay is a type of soil with particles of certain minerals giving plastic properties when mixed with water. Soil has an important role in a construction, besides as a building material in a wide variety of civil engineering works, soil is also used as supporting foundation of the building. Basic properties of clay are rock-solid in dry and plastic with medium water content. In high water content, clay becomes sticky like (cohesive) and soften. Therefore, clay stabilization is necessary to repair soil’s mechanical properties. In this research, lime is use as a stabilizer that contains the Ca+ element to bond bigger particles. Lime used is slaked lime Ca(OH)2. Clay used has liquid limitation (LL) value of 47.33%, plasticity index of 29.88% and CBR value 6.29. The results explain about 10% lime mixture variation gives the optimum stabilized clay with CBR value of 8.75%.

Results from the Mars global surveyor thermal emission spectrometer

USGS Publications Warehouse

Christensen, P.R.; Anderson, D.L.; Chase, S.C.; Clancy, R.T.; Clark, R.N.; Conrath, B.J.; Kieffer, H.H.; Kuzmin, R.O.; Malin, M.C.; Pearl, J.C.; Roush, T.L.; Smith, M.D.

1998-01-01

The Thermal Emission Spectrometer spectra of low albedo surface materials suggests that a four to one mixture of pyroxene to plagioclase, together with about a 35 percent dust component provides the best fit to the spectrum. Qualitative upper limits can be placed on the concentration of carbonates (<10 percent), olivine (<10 percent), clay minerals (<20 percent), and quartz (<5 percent) in the limited regions observed. Limb observations in the northern hemisphere reveal low-lying dust hazes and detached water-ice clouds at altitudes up to 55 kilometers. At an aerocentric longitude of 224??a major dust storm developed in the Noachis Terra region. The south polar cap retreat was similar to that observed by Viking.

Leg 67: the Deep Sea Drilling Project Mid-America Trench transect off Guatemala.

USGS Publications Warehouse

von Huene, Roland E.

1980-01-01

Drilling on the Cocos plate recovered a basal chalk sequence deposited during early and mid-Miocene time, a short interval of abyssal red clay, and an upper sequence of late Miocene and younger sediment deposited within an area influenced by a terrigenous source. In the trench, a mud and sand fill less than 400,000 yr old overlies the oceanic sequence. The entire section shows no evidence of compressive deformation. In contrast, the section cored on the trench's landward slope 3 km from the trench axis is affected by tectonism. The section contains a Cretaceous to Pliocene claystone sequence capped by Pliocene to Quaternary hemipelagic slope deposits.- from Authors

Establishing diagnostic cut-off criteria for the COBAS AmpliPrep/COBAS TaqMan HIV-1 Qualitative test through validation against the Amplicor DNA test v1.5 for infant diagnosis using dried blood spots.

PubMed

Maritz, Jean; Preiser, Wolfgang; van Zyl, Gert U

2012-02-01

As antibody testing cannot confirm HIV-1 infection in children less than 18 months of age, diagnosis in these children depends on nucleic acid testing. The COBAS(®) AmpliPrep/COBAS(®) TaqMan(®) (CAP/CTM, Roche(®) Molecular Systems, Inc., Branchburg, NJ) HIV-1 Qualitative test is a total nucleic acid real-time PCR assay utilising whole EDTA blood or dried blood spots (DBS), which recently replaced the Roche(®) AMPLICOR(®) DNA test v1.5 (Amplicor) as the diagnostic HIV PCR assay in many South African laboratories. For the Amplicor assay, stringent diagnostic criteria were previously formulated for the local population, and a comparison reported the CAP/CTM's sensitivity at 99.7% and specificity at 100% for both sample types compared to these Amplicor criteria. To validate the assay prior to introduction in our laboratory and to define stringent diagnostic cut-off criteria. Whole EDTA blood samples from patients younger than 18 months sent for routine HIV-1 diagnosis were tested by Amplicor, and positive results were confirmed from DBS. CAP/CTM assays were subsequently performed from DBS. The CAP/CTM had a sensitivity of 98.8% and a specificity of 97.1%, but a positive predictive value (PPV) of only 78.7% compared to the Amplicor assay. Samples positive by CAP/CTM but negative by Amplicor displayed poor amplification curves compared to concordant positive samples. Upon re-testing those with sufficient material available by CAP/CTM, all showed negative results. The decreased PPV may either be due to false positive CAP/CTM results, or increased sensitivity compared to the Amplicor assay. Criteria were formulated for defining presumed false-positive results. Copyright © 2011 Elsevier B.V. All rights reserved.

Development and evaluation of a contrast sensitivity perimetry test for patients with glaucoma.

PubMed

Hot, Aliya; Dul, Mitchell W; Swanson, William H

2008-07-01

To design a contrast sensitivity perimetry (CSP) protocol that decreases variability in glaucomatous defects while maintaining good sensitivity to glaucomatous loss. Twenty patients with glaucoma and 20 control subjects were tested with a CSP protocol implemented on a monitor-based testing station. In the protocol 26 locations were tested over the central visual field with Gabor patches with a peak spatial frequency of 0.4 cyc/deg and a two-dimensional spatial Gaussian envelope, with most of the energy concentrated within a 4 degrees circular region. Threshold was estimated by a staircase method: Patients and 10 age-similar control subjects were also tested on conventional automated perimetry (CAP), with the 24-2 pattern with the SITA Standard testing strategy. The neuroretinal rim area of the patients was measured with a retinal tomograph (Retina Tomograph II [HRT]; Heidelberg Engineering, Heidelberg, Germany). A Bland-Altman analysis of agreement was used to assess test-retest variability, compare depth of defect shown by the two perimetric tests, and investigate the relations between contrast sensitivity and neuroretinal rim area. Variability showed less dependence on defect depth for CSP than for CAP (z = 9.3, P < 0.001). Defect depth was similar for CAP and CSP when averaged by quadrant (r = 0.26, P > 0.13). The relation between defect depth and rim area was more consistent with CSP than with CAP (z = 9, P < 0.001). The implementation of CSP was successful in reducing test-retest variability in glaucomatous defects. CSP was in general agreement with CAP in terms of depth of defect and was in better agreement than CAP with HRT-determined rim area.

Termites utilise clay to build structural supports and so increase foraging resources

PubMed Central

Oberst, Sebastian; Lai, Joseph C. S.; Evans, Theodore A.

2016-01-01

Many termite species use clay to build foraging galleries and mound-nests. In some cases clay is placed within excavations of their wooden food, such as living trees or timber in buildings; however the purpose for this clay is unclear. We tested the hypotheses that termites can identify load bearing wood, and that they use clay to provide mechanical support of the load and thus allow them to eat the wood. In field and laboratory experiments, we show that the lower termite Coptotermes acinaciformis, the most basal species to build a mound-nest, can distinguish unloaded from loaded wood, and use clay differently when eating each type. The termites target unloaded wood preferentially, and use thin clay sheeting to camouflage themselves while eating the unloaded wood. The termites attack loaded wood secondarily, and build thick, load-bearing clay walls when they do. The termites add clay and build thicker walls as the load-bearing wood is consumed. The use of clay to support wood under load unlocks otherwise unavailable food resources. This behaviour may represent an evolutionary step from foraging behaviour to nest building in lower termites. PMID:26854187

An alternate lining scheme for solar ponds - Results of a liner test rig

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raman, P.; Kishore, V.V.N.

1990-01-01

Solar pond lining schemes consisting of combinations of clays and Low Density Polyethylene (LDPE) films have been experimentally evaluated by means of a Solar Pond Liner Test Rig. Results indicate that LDPE film sandwiched between two layers of clay can be effectively used for lining solar ponds.

ANALYSIS OF A GAS-PHASE PARTITIONING TRACER TEST CONDUCTED IN AN UNSATURATED FRACTURED-CLAY FORMATION

EPA Science Inventory

The gas-phase partitioning tracer method was used to estimate non-aqueous phase liquid (NAPL), water, and air saturations in the vadose zone at a chlorinated-solvent contaminated field site in Tucson, AZ. The tracer test was conducted in a fractured-clay system that is the confin...

Performance of Kaolin Clay on the Concrete Pavement

NASA Astrophysics Data System (ADS)

Abdullah, M. E.; Jaya, R. P.; Shahafuddin, M. N. A.; Yaacob, H.; Ibrahim, M. H. Wan; Nazri, F. M.; Ramli, N. I.; Mohammed, A. A.

2018-05-01

This paper investigates the performance of concrete pavement containing kaolin clay with their engineering properties and to determine the optimum kaolin clay content. The concrete used throughout the study was designed as grade 30 MPa strength with constant water to cement ratio of 0.49. The compressive strength, flexural strength and water absorption test was conducted in this research. The concrete mix designed with kaolin clay as cement replacement comprises at 0%, 5%, 10% and 15% by the total weight of cement. The results indicate that the strength of pavement concrete decreases as the percentage of kaolin clay increases. It also shows that the water absorption increases with the percentage of cement replacement. However, 5% kaolin clay is found to be the optimum level to replace cement in a pavement concrete.

Design and testing of a pilot scale magnetic separator for the treatment of textile dyeing wastewater.

PubMed

Salinas, Tobías; Durruty, Ignacio; Arciniegas, Lorena; Pasquevich, Gustavo; Lanfranconi, Matías; Orsi, Isabela; Alvarez, Vera; Bonanni, Sebastian

2018-07-15

Iron nanoparticles can be incorporated on the structure of natural clays to obtain magnetic clays, an adsorbent that be easily removed from a wastewater by magnetic means. Magnetic clays have high adsorption capacities of different contaminants such as heavy metals, fungicides, aromatic compounds and colorants and show rapid adsorption kinetics, but crucial data for achieving its full or pilot scale application is still lacking. In this work, magnetic bentonites with different amounts of magnetite (iron fractions on the clay of 0.55, 0.6 and 0.6) were used to remove color from a real textile wastewater. On a first stage the optimal conditions for the adsorption of the dye, including pH, temperature and clay dosage were determined. Also design parameters for the separation process such as residence time, distance from magnet to magnetic clay and magnet strength were obtained. Finally a pilot scale magnetic drum separator was constructed and tested. A removal of 60% of the dye from a wastewater that contained more than 250 ppm of azo dye was achieved with only 10 min of residence time inside the separator. Copyright © 2018 Elsevier Ltd. All rights reserved.

Testosterone sorption and desorption: effects of soil particle size.

PubMed

Qi, Yong; Zhang, Tian C; Ren, Yongzheng

2014-08-30

Soils contain a wide range of particles of different diameters with different mobility during rainfall events. Effects of soil particles on sorption and desorption behaviors of steroid hormones have not been investigated. In this study, wet sieve washing and repeated sedimentation methods were used to fractionate the soils into five ranges. The sorption and desorption properties and related mechanisms of testosterone in batch reactors filled with fractionated soil particles were evaluated. Results of sorption and desorption kinetics indicate that small soil particles have higher sorption and lower desorption rates than that of big ones. Thermodynamic results show the sorption processes are spontaneous and exothermal. The sorption capacity ranks as clay>silt>sand, depending mainly on specific surface area and surface functional groups. The urea control test shows that hydrogen bonding contributes to testosterone sorption onto clay and silt but not on sand. Desorption tests indicate sorption is 36-65% irreversible from clay to sand. Clays have highest desorption hysteresis among these five soil fractions, indicating small particles like clays have less potential for desorption. The results provide indirect evidence on the colloid (clay)-facilitated transport of hormones (micro-pollutants) in soil environments. Copyright © 2014 Elsevier B.V. All rights reserved.

488-1D Ash Basin closure cap help modeling- Microdrain® liner option

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyer, J. A.

At the request of Area Completion Engineering and in support of the 488-1D Ash Basin closure, the Savannah River National Laboratory (SRNL) performed hydrologic simulations of the revised 488-1D Ash Basin closure cap design using the Hydrologic Evaluation of Landfill Performance (HELP) model. The revised design substitutes a MicroDrain Liner®—60-mil low-density polyethylene geomembrane structurally integrated with 130-mil drainage layer—for the previously planned drainage/barrier system—300-mil geosynthetic drainage layer (GDL), 300-mil geosynthetic clay liner (GCL), and 6-inch common fill soil layer. For a 25-year, 24-hour storm event, HELP model v3.07 was employed to (1) predict the peak maximum daily hydraulic head formore » the geomembrane layer, and (2) ensure that South Carolina Department of Health and Environmental Control (SCDHEC) requirements for the barrier layer (i.e., ≤ 12 inches hydraulic head on top of a barrier having a saturated hydraulic conductivity ≤ 1.0E-05 cm/s) will not be exceeded. A 25-year, 24-hour storm event at the Savannah River Site (SRS) is 6.1 inches rainfall (Weber 1998). HELP model v3.07 results based upon the new planned cap design suggest that the peak maximum daily hydraulic head on the geomembrane barrier layer will be 0.15 inches for a minimum slope equal to 3%, which is two orders of magnitude below the SCDHEC upper limit of 12 inches.« less

488-1D Ash basin closure cap help modeling-Microdrain® liner option

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyer, J.

At the request of Area Completion Engineering and in support of the 488-1D Ash Basin closure, the Savannah River National Laboratory (SRNL) performed hydrologic simulations of the revised 488-1D Ash Basin closure cap design using the Hydrologic Evaluation of Landfill Performance (HELP) model. The revised design substitutes a MicroDrain Liner®—50-mil linear low-density polyethylene geomembrane structurally integrated with 130-mil drainage layer—for the previously planned drainage/barrier system—300-mil geosynthetic drainage layer (GDL), 300-mil geosynthetic clay liner (GCL), and 6-inch common fill soil layer. For a 25-year, 24-hour storm event, HELP model v3.07 was employed to (1) predict the peak maximum daily hydraulic headmore » for the geomembrane layer, and (2) ensure that South Carolina Department of Health and Environmental Control (SCDHEC) requirements for the barrier layer (i.e., ≤ 12 inches hydraulic head on top of a barrier having a saturated hydraulic conductivity ≤ 1.0E-05 cm/s) will not be exceeded. A 25-year, 24-hour storm event at the Savannah River Site (SRS) is 6.1 inches rainfall (Weber 1998). HELP model v3.07 results based upon the new planned cap design suggest that the peak maximum daily hydraulic head on the geomembrane barrier layer will be 0.179 inches for a minimum slope equal to 3%, which is approximately two orders of magnitude below the SCDHEC upper limit of 12 inches.« less

Delineation of a quick clay zone at Smørgrav, Norway, with electromagnetic methods under geotechnical constraints

NASA Astrophysics Data System (ADS)

Kalscheuer, Thomas; Bastani, Mehrdad; Donohue, Shane; Persson, Lena; Aspmo Pfaffhuber, Andreas; Reiser, Fabienne; Ren, Zhengyong

2013-05-01

In many coastal areas of North America and Scandinavia, post-glacial clay sediments have emerged above sea level due to iso-static uplift. These clays are often destabilised by fresh water leaching and transformed to so-called quick clays as at the investigated area at Smørgrav, Norway. Slight mechanical disturbances of these materials may trigger landslides. Since the leaching increases the electrical resistivity of quick clay as compared to normal marine clay, the application of electromagnetic (EM) methods is of particular interest in the study of quick clay structures. For the first time, single and joint inversions of direct-current resistivity (DCR), radiomagnetotelluric (RMT) and controlled-source audiomagnetotelluric (CSAMT) data were applied to delineate a zone of quick clay. The resulting 2-D models of electrical resistivity correlate excellently with previously published data from a ground conductivity metre and resistivity logs from two resistivity cone penetration tests (RCPT) into marine clay and quick clay. The RCPT log into the central part of the quick clay identifies the electrical resistivity of the quick clay structure to lie between 10 and 80 Ω m. In combination with the 2-D inversion models, it becomes possible to delineate the vertical and horizontal extent of the quick clay zone. As compared to the inversions of single data sets, the joint inversion model exhibits sharper resistivity contrasts and its resistivity values are more characteristic of the expected geology. In our preferred joint inversion model, there is a clear demarcation between dry soil, marine clay, quick clay and bedrock, which consists of alum shale and limestone.

Geotechnical and mineralogical characteristics of marl deposits in Jordan

NASA Astrophysics Data System (ADS)

Shaqour, Fathi M.; Jarrar, Ghaleb; Hencher, Steve; Kuisi, Mostafa

2008-10-01

Marls and marly limestone deposits cover most of Northern Jordan, where Amman City and its suburbs are located. These deposits serve as foundations for most buildings and roads as well as fill material for structural back filling, especially road bases and sub-bases. The present study aims at investigating the geotechnical characteristics and mineral composition of the marl units of these deposits through field investigations and laboratory testing. Using X-ray diffraction technique along with chemical analysis, representative samples of marl horizons were tested for mineral composition, and for a set of index and geotechnical properties including: specific gravity, grain size, Atterberg limits, Proctor compaction and shear strength properties. The test results show a positive linear relationship as expected between the clay content and both liquid and plastic limits. The tests results also show an inverse linear relationship between the clay content and the maximum dry density in both standard and modified compaction. This is attributed to the adsorption of water by the clay minerals. The relationship is more prominent in the case of modified compaction test. The results also indicate a similar relationship for the angle of internal friction. No clear correlation between cohesion and clay content was apparent.

Results of hydraulic tests in U.S. Department of Energy's wells DOE-4, 5, 6, 7, 8, and 9, Salt Valley, Grand County, Utah

USGS Publications Warehouse

Wollitz, Leonard E.; Thordarson, William; Whitfield, Merrick S.; Weir, James E.

1982-01-01

Six exploratory wells were drilled into the cap rock underlying Salt Valley, Utah, for geologic, geophysical, and hydrologic data to augment information obtained from three previous test wells. Drilling of three other test holes was abandoned due to caving and loss of drilling tools, Before reaching the zone of saturation; the upper 100 meters of cap rock is unsaturated. Within the saturated part of the cap rock, hydraulic heads generally decrease with depth and to the northwest in this part of the valley.Hydraulic conductivity of the cap rock, as determined from pumping tests, ranged from 9.3 X 10-5 to 2.06 X 10-1 meters per day; as a result, groundwater flow rates in the cap rock are low. Water ranges from a calcium bicarbonate sulfate type on the western edge of the valley to a calcium magnesium sodium bicarbonate, sulfate, chloride type near the center of the valley. Carbon-14 specific activity for cap-rock water yielded an uncorrected age of about 17,000 to 26,000 years before present near the western edge of the valley and about 41,000 years before present near the center of the valley.

Comparative ecotoxicity of chlorantraniliprole to non-target soil invertebrates.

PubMed

Lavtižar, Vesna; Berggren, Kristina; Trebše, Polonca; Kraak, Michiel H S; Verweij, Rudo A; van Gestel, Cornelis A M

2016-09-01

The insecticide chlorantraniliprole (CAP) is gaining importance in agricultural practice, but data on its possible negative effects on non-target organisms is severely deficient. This study therefore determined CAP toxicity to non-target soil invertebrates playing a crucial role in ecosystem functioning, including springtails (Folsomia candida), isopods (Porcellio scaber), enchytraeids (Enchytraeus crypticus) and oribatid mites (Oppia nitens). In sublethal toxicity tests in Lufa 2.2 soil, chronic exposure to CAP concentrations up to 1000 mg/kgdw did not affect the survival and reproduction of E. crypticus and O. nitens nor the survival, body weight and consumption of P. scaber. In contrast, the survival and reproduction of F. candida was severely affected, with an EC50 for effects on reproduction of 0.14 mg CAP/kgdw. The toxicity of CAP to the reproduction of F. candida was tested in four different soils following OECD guideline 232, and additionally in an avoidance test according to ISO guideline 17512-2. A significantly lower toxicity in soils rich in organic matter was observed, compared to low organic soils. Observations in the avoidance test with F. candida suggest that CAP acted in a prompt way, by affecting collembolan locomotor abilities thus preventing them from escaping contaminated soil. This study shows that CAP may especially pose a risk to non-target soil arthropods closely related to insects, while other soil invertebrates seem rather insensitive. Copyright © 2016 Elsevier Ltd. All rights reserved.

Implementation of DSC model and application for analysis of field pile tests under cyclic loading

NASA Astrophysics Data System (ADS)

Shao, Changming; Desai, Chandra S.

2000-05-01

The disturbed state concept (DSC) model, and a new and simplified procedure for unloading and reloading behavior are implemented in a nonlinear finite element procedure for dynamic analysis for coupled response of saturated porous materials. The DSC model is used to characterize the cyclic behavior of saturated clays and clay-steel interfaces. In the DSC, the relative intact (RI) behavior is characterized by using the hierarchical single surface (HISS) plasticity model; and the fully adjusted (FA) behavior is modeled by using the critical state concept. The DSC model is validated with respect to laboratory triaxial tests for clay and shear tests for clay-steel interfaces. The computer procedure is used to predict field behavior of an instrumented pile subjected to cyclic loading. The predictions provide very good correlation with the field data. They also yield improved results compared to those from a HISS model with anisotropic hardening, partly because the DSC model allows for degradation or softening and interface response.

In situ characterization of organo-modified and unmodified montmorillonite aqueous suspensions by UV-visible spectroscopy.

PubMed

Alin, Jonas; Rubino, Maria; Auras, Rafael

2015-10-15

UV-visible (UV-Vis) spectroscopy (Tyndall spectra) was applied and tested for its ability to measure organo-modified and unmodified montmorillonite (MMT) clays in aqueous suspensions. A full factorial design of experiments was used to study the influence of pH, NaCl and clay concentrations on the average particle size of the clay agglomerates. The methodology was evaluated by observing results that were consistent with previous research about the unmodified clay's behavior in aqueous suspensions. The results from this evaluation corresponded to accepted theories about the unmodified clay's behavior, indicating that the methodology is precise enough to distinguish the effects of the studied factors on these clay suspensions. The effect of clay concentration was related to the amount of ions per clay particle for the unmodified clay, but was not significant for the organo-modified MMT. The average particle size of the organo-modified MMT in suspension was significantly larger than that of the unmodified clay. Size of the organo-modified MMT agglomerates in suspension decreased in the presence of NaCl and at both high and low pH; this behavior was opposite to that of the unmodified clay. These results demonstrate that the UV-Vis methodology is well-suited for characterizing clay particle size in aqueous suspensions. The technique also is simple, rapid, and low-cost. Copyright © 2015 Elsevier Inc. All rights reserved.

Precast, Prestressed Concrete Bent Caps : Volume 2, Design Recommendations and Design Examples

DOT National Transportation Integrated Search

2018-04-01

Recommendations for design of pretensioned bent caps are developed based on the findings of full-scale experimental tests of bent cap subassemblages. Companion examples are provided to demonstrate implementation of the design recommendations. First, ...

Neoprene pads for capping concrete cylinders.

DOT National Transportation Integrated Search

1979-01-01

The possibility of using neoprene pads as an alternate to sulfur mortar for capping concrete specimens subjected to compression tests was investigated. In preliminary tests to determine the feasibility of the investigation, two batches of concrete we...

The application of halloysite tubule nanoclay in drug delivery.

PubMed

Lvov, Yuri M; DeVilliers, Melgardt M; Fakhrullin, Rawil F

2016-07-01

Natural and biocompatible clay nanotubes are among the best inorganic materials for drug nanoformulations. These halloysite tubes with SiO2 on the outermost surface have diameter of ca. 50 nm, length around 1 micrometer and may be loaded with drugs at 10-30 wt. %. Narrow tube openings allow for controllable sustained drug release for hours, days or even weeks. Physical-chemical properties of these nanotubes are described followed by examples of drug-loading capabilities, release characteristics, and control of duration of release through the end tube capping with polymers. Development of halloysite-polymer composites such as tissue scaffolds and bone cement/dentist resin formulations with enhanced mechanical properties and extension of the drug release to 2-3 weeks are described. Examples of the compression properties of halloysite in tablets and capsules are also shown. We expect that clay nanotubes will be used primarily for non-injectable drug formulations, such as topical and oral dosage forms, cosmetics, as well as for composite materials with enhanced therapeutic effects. These include tissue scaffolds, bone cement and dentist resins with sustained release of antimicrobial and cell growth-promoting medicines (including proteins and DNA) as well as other formulations such as compounds for antiseptic treatment of hospitals.

Chemical and mineralogical characteristics of French green clays used for healing

USGS Publications Warehouse

Williams, Lynda B.; Haydel, Shelley E.; Giese, Rossman F.; Eberl, Dennis D.

2008-01-01

The worldwide emergence of infectious diseases, together with the increasing incidence of antibiotic-resistant bacteria, elevate the need to properly detect, prevent, and effectively treat these infections. The overuse and misuse of common antibiotics in recent decades stimulates the need to identify new inhibitory agents. Therefore, natural products like clays, that display antibacterial properties, are of particular interest.The absorptive properties of clay minerals are well documented for healing skin and gastrointestinal ailments. However, the antibacterial properties of clays have received less scientific attention. French green clays have recently been shown to heal Buruli ulcer, a necrotic or ‘flesh-eating’ infection caused by Mycobacterium ulcerans. Assessing the antibacterial properties of these clays could provide an inexpensive treatment for Buruli ulcer and other skin infections.Antimicrobial testing of the two clays on a broad-spectrum of bacterial pathogens showed that one clay promotes bacterial growth (possibly provoking a response from the natural immune system), while another kills bacteria or significantly inhibits bacterial growth. This paper compares the mineralogy and chemical composition of the two French green clays used in the treatment of Buruli ulcer.Mineralogically, the two clays are dominated by 1Md illite and Fe-smectite. Comparing the chemistry of the clay minerals and exchangeable ions, we conclude that the chemistry of the clay, and the surface properties that affect pH and oxidation state, control the chemistry of the water used to moisten the clay poultices and contribute the critical antibacterial agent(s) that ultimately debilitate the bacteria.

Field Evaluation of the Sidestream Sensors for Filter/Separators and Clay Filters.

DTIC Science & Technology

1987-02-01

originally, but only the Atlanta and New York ( JFK ) airports produced suitable test results. At O’Hare (Chicago) Airport, the operator advised the...the JFK Airport installation, every one of the eight test runs terminated prematurely because solids caused pressure drop buildup before any surfactant...about 20 points. In this test period, the high CSS rating also confirmed the activity of the clay. At JFK Airport , the CSS was tested on 27 occasions

Effects of chronic plus acute prolonged stress on measures of coping style, anxiety, and evoked HPA-axis reactivity.

PubMed

Roth, Megan K; Bingham, Brian; Shah, Aparna; Joshi, Ankur; Frazer, Alan; Strong, Randy; Morilak, David A

2012-11-01

Exposure to psychological trauma is the precipitating factor for PTSD. In addition, a history of chronic or traumatic stress exposure is a predisposing risk factor. We have developed a Chronic plus Acute Prolonged Stress (CAPS) treatment for rats that models some of the characteristics of stressful events that can lead to PTSD in humans. We have previously shown that CAPS enhances acute fear responses and impairs extinction of conditioned fear. Further, CAPS reduced the expression of glucocorticoid receptors in the medial prefrontal cortex. In this study we examined the effects of CAPS exposure on behavioral stress coping style, anxiety-like behaviors, and acute stress reactivity of the hypothalamic-pituitary-adrenal (HPA) axis. Male Sprague-Dawley rats were exposed to CAPS treatment, consisting of chronic intermittent cold stress (4 °C, 6 h/day, 14 days) followed on day 15 by a single 1-h session of sequential acute stressors (social defeat, immobilization, swim). After CAPS or control treatment, different groups were tested for shock probe defensive burying, novelty suppressed feeding, or evoked activation of adrenocorticotropic hormone (ACTH) and corticosterone release by an acute immobilization stress. CAPS resulted in a decrease in active burying behavior and an increase in immobility in the shock probe test. Further, CAPS-treated rats displayed increases in the latency to feed in the novelty suppressed feeding test, despite an increase in food intake in the home cage. CAPS treatment also reduced the HPA response to a subsequent acute immobilization stress. These results further validate CAPS treatment as a rat model of relevance to PTSD, and together with results reported previously, suggest that CAPS impairs fear extinction, shifts coping behavior from an active to a more passive strategy, increases anxiety, and alters HPA reactivity, resembling many aspects of human PTSD. Copyright © 2012 Elsevier Ltd. All rights reserved.

Rapid Stabilization/Polymerization of Wet Clay Soils; Literature Review

DTIC Science & Technology

2009-01-15

known as lime, and potassium hydroxide (KOH) were found to increase shear strength, and decrease expansive properties of Diablo clay. The lime...Publication Date: 1991 Purpose of Stabilizer: Control High Swell Potential Stabilizers Tested: Lime, potassium phosphate, potassium chloride...Date: 1988 Purpose of Stabilizer: Stabilizer Stabilizers Tested: Hydroxy-aluminum, hydroxy-aluminum and potassium chloride, hydroxy-aluminum

Tactical Wheeled Vehicle Survivability: Results of Experiments to Quantify Aboveground Impulse

DTIC Science & Technology

2010-03-01

in each testbed are pre- sented in Table 4.7. For all the clay soil experiments, the mean value of wet density was 121.2 lb/ft3, and the mean value...4.7. Summary of clay soil test series. Experiment Number Charge Position Avg Wet Density , lb/ft3 Avg Dry Density , lb/ft3 Avg Water... Clay soil ................................................................................................................................... 81

Short- and long-term effects of a lactose-restricted diet and probiotics in children with chronic abdominal pain: a retrospective study.

PubMed

Ockeloen, L E; Deckers-Kocken, J M

2012-05-01

To determine the short- and long-term effect of treatment in children with chronic abdominal pain (CAP). A database with the results of H(2) breath test of children with CAP was created. All children with an abnormal test result were included and classified as small intestinal bacterial overgrowth (SIBO) or lactose intolerant (LTI). SIBO was treated with probiotics and LTI with a lactose-restricted diet. CAP was evaluated 5 months and 15 months after the test. 37 children (41%) were included. 17 LTI children (94%) improved after 5 months and 11 children (61%) after 15 months (P<0.05). Seven SIBO children improved after 5 months and 4 children after 15 months. In the combination group all 4 children improved after 5 months and 3 children after 15 months. Children with CAP caused by LTI or SIBO had less CAP after 5 months. This positive effect persists only in half of the children. Copyright © 2011 Elsevier Ltd. All rights reserved.

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, workers remove the overhead crane from the nose cap that was removed from Atlantis. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

NASA Image and Video Library

2003-10-29

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, workers remove the overhead crane from the nose cap that was removed from Atlantis. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, the nose cap from Atlantis is secured on a shipping pallet. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

NASA Image and Video Library

2003-10-29

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, the nose cap from Atlantis is secured on a shipping pallet. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, packing material is placed over the nose cap that was removed from Atlantis. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

NASA Image and Video Library

2003-10-29

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, packing material is placed over the nose cap that was removed from Atlantis. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, the nose cap from Atlantis is lowered toward a shipping pallet. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

NASA Image and Video Library

2003-10-29

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, the nose cap from Atlantis is lowered toward a shipping pallet. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

Activation of a Ca-bentonite as buffer material

NASA Astrophysics Data System (ADS)

Huang, Wei-Hsing; Chen, Wen-Chuan

2016-04-01

Swelling behavior is an important criterion in achieving the low-permeability sealing function of buffer material. A potential buffer material may be used for radioactive waste repository in Taiwan is a locally available clayey material known as Zhisin clay, which has been identified as a Ca-bentonite. Due to its Ca-based origin, Zhisin was found to exhibit swelling capacity much lower than that of Na-bentonite. To enhance the swelling potential of Zhisin clay, a cation exchange process by addition of Na2CO3 powder was introduced in this paper. The addition of Na2CO3 reagent to Zhisin clay, in a liquid phase, caused the precipitation of CaCO3 and thereby induced a replacement of Ca2+ ions by Na+ ions on the surface of bentonite. Characterization test conducted on Zhisin clay includes chemical analysis, cation exchange capacity, X-ray diffraction, and thermogravimetry (TG). Free-swelling test apparatus was developed according to International Society of Rock Mechanics recommendations. A series of free-swelling tests were conducted on untreated and activated specimens to characterize the effect of activation on the swelling capacity of Zhisin clay. Efforts were made to determine an optimum dosage for the activation, and to evaluate the aging effect. Also, the activated material was evaluated for its stability in various hydrothermal conditions for potential applications as buffer material in a repository. Experimental results show that Na2CO3-activated Zhisin clay is superior in swelling potential to untreated Zhisin clay. Also, there exists an optimum amount of activator in terms of improvements in the swelling capacity. A distinct time-swell relationship was discovered for activated Zhisin clay. The corresponding mechanism refers to exchange of cations and breakdown of quasi-crystal, which results in ion exchange hysteresis of Ca-bentonite. Due to the ion exchange hysteresis, activated bentonite shows a post-rise time-swell relationship different than the sigmoid-shaped time-swell curves of typical bentonites. That is, a greater part of swelling strain develops after the completion of primary swelling strain. At an optimal amount of 1% Na2CO3 in weight, the maximum swelling strain was found to be 3 times as much as that of untreated Zhisin clay. Furthermore, the Na2CO3-activated Zhisin clay exhibited improved resistance to thermal environments and behaved similar to Na-type bentonites under various hydrothermal temperatures.

Modified clay minerals efficiency against chemical and biological warfare agents for civil human protection.

PubMed

Plachá, Daniela; Rosenbergová, Kateřina; Slabotínský, Jiří; Kutláková, Kateřina Mamulová; Studentová, Soňa; Martynková, Gražyna Simha

2014-04-30

Sorption efficiencies of modified montmorillonite and vermiculite of their mono ionic Na and organic HDTMA and HDP forms were studied against chemical and biological warfare agents such as yperite and selected bacterial strains. Yperite interactions with modified clay minerals were observed through its capture in low-density polyethylene foil-modified clay composites by measuring yperite gas permeation with using chemical indication and gas chromatography methods. The antibacterial activities of synthetized organoclays were tested against selected Gram-positive and Gram-negative bacterial species in minimum inhibitory concentration tests. The obtained results showed a positive influence of modified clay minerals on the significant yperite breakthrough-time increase. The most effective material was the polyethylene-Na form montmorillonite, while the polyethylene-Na form vermiculite showed the lowest efficiency. With increasing organic cations loading in the interlayer space the montmorillonite efficiency decreased, and in the case of vermiculite an opposite effect was observed. Generally the modified montmorillonites were more effective than modified vermiculites. The HDP cations seem to be more effective compare to the HDTMA. The antibacterial activity tests confirmed efficiency of all organically modified clay minerals against Gram-positive bacteria. The confirmation of antibacterial activity against Y. pestis, plague bacteria, is the most interesting result of this part of the study. Copyright © 2014 Elsevier B.V. All rights reserved.

Reducing the Cation Exchange Capacity of Lithium Clay to Form Better Dispersed Polymer-Clay Nanocomposites

NASA Technical Reports Server (NTRS)

Liang, Maggie

2004-01-01

Polymer-clay nanocomposites have exhibited superior strength and thermo- oxidative properties as compared to pure polymers for use in air and space craft; however, there has often been difficulty completely dispersing the clay within the matrices of the polymer. In order to improve this process, the cation exchange capacity of lithium clay is first lowered using twenty-four hour heat treatments of no heat, 130 C, 150 C, or 170 C to fixate the lithium ions within the clay layers so that they are unexchangeable. Generally, higher temperatures have generated lower cation exchange capacities. An ion exchange involving dodecylamine, octadecylamine, or dimethyl benzidine (DMBZ) is then employed to actually expand the clay galleries. X-ray diffraction and transmission electron microscopy can be used to determine whether the clay has been successfully exfoliated. Finally, resins of DMBZ with clay are then pressed into disks for characterization using dynamic mechanical analyzer and oven- aging techniques in order to evaluate their glass transition, modulus strength, and thermal-oxidative stability in comparison to neat DMBZ. In the future, they may also be tested as composites for flexural and laminar shear strength.

How could a freshwater swamp produce a chemical signature characteristic of a saltmarsh?

USGS Publications Warehouse

McCloskey, Terrence; Smith, Christopher G.; Liu, Kam-biu; Marot, Marci E.; Haller, Christian

2018-01-01

Reduction–oxidation (redox) reaction conditions, which are of great importance for the soil chemistry of coastal marshes, can be temporally dynamic. We present a transect of cores from northwest Florida wherein radical postdepositional changes in the redox regime has created atypical geochemical profiles at the bottom of the sedimentary column. The stratigraphy is consistent along the transect, consisting of, from the bottom upward, carbonate bedrock, a gray clay, an organic mud section, a dense clay layer, and an upper organic mud unit representing the current saltwater marsh. However, the geochemical signature of the lower organic mud unit suggests pervasive redox reactions, although the interval has been identified as representing a freshwater marsh, an unlikely environment for such conditions. Analyses indicate that this discrepancy results from postdepositional diagenesis driven by millennial-scale environmental parameters. Rising sea level that led to the deposition of the capping clay layer, created anaerobic conditions in the freshwater swamp interval, and isolated it hydrologically from the rest of the sediment column. The subsequent infiltration of marine water into this organic material led to sulfate reduction, the buildup of H2S and FeS, and anoxic conditions. Continued sulfidation eventually resulted in euxinic conditions, as evidenced by elevated levels of Fe, S, and especially Mo, the diagnostic marker of euxinia. Because this chemical transformation occurred long after the original deposition the geochemical signature does not reflect soil chemistry at the time of deposition and cannot be used to infer syn-depositional environmental conditions, emphasizing the importance of recognizing diagenetic processes in paleoenvironmental studies.

Novel Organically Modified Core-Shell Clay for Epoxy Composites-"SOBM Filler 1".

PubMed

Iheaturu, Nnamdi Chibuike; Madufor, Innocent Chimezie

2014-01-01

Preparation of a novel organically modified clay from spent oil base drilling mud (SOBM) that could serve as core-shell clay filler for polymers is herein reported. Due to the hydrophilic nature of clay, its compatibility with polymer matrix was made possible through modification of the surface of the core clay sample with 3-aminopropyltriethoxysilane (3-APTES) compound prior to its use. Fourier transform infrared (FT-IR) spectroscopy was used to characterize clay surface modification. Electron dispersive X-ray diffraction (EDX) and scanning electron microscopy (SEM) were used to expose filler chemical composition and morphology, while electrophoresis measurement was used to examine level of filler dispersion. Results show an agglomerated core clay powder after high temperature treatment, while EDX analysis shows that the organically modified clay is composed of chemical inhomogeneities, wherein elemental compositions in weight percent vary from one point to the other in a probe of two points. Micrographs of the 3-APTES coupled SOBM core-shell clay filler clearly show cloudy appearance, while FT-IR indicates 25% and 5% increases in fundamental vibrations band at 1014 cm(-1) and 1435 cm(-1), respectively. Furthermore, 3-APTES coupled core-shell clay was used to prepare epoxy composites and tested for mechanical properties.

Novel Organically Modified Core-Shell Clay for Epoxy Composites—“SOBM Filler 1”

PubMed Central

Iheaturu, Nnamdi Chibuike; Madufor, Innocent Chimezie

2014-01-01

Preparation of a novel organically modified clay from spent oil base drilling mud (SOBM) that could serve as core-shell clay filler for polymers is herein reported. Due to the hydrophilic nature of clay, its compatibility with polymer matrix was made possible through modification of the surface of the core clay sample with 3-aminopropyltriethoxysilane (3-APTES) compound prior to its use. Fourier transform infrared (FT-IR) spectroscopy was used to characterize clay surface modification. Electron dispersive X-ray diffraction (EDX) and scanning electron microscopy (SEM) were used to expose filler chemical composition and morphology, while electrophoresis measurement was used to examine level of filler dispersion. Results show an agglomerated core clay powder after high temperature treatment, while EDX analysis shows that the organically modified clay is composed of chemical inhomogeneities, wherein elemental compositions in weight percent vary from one point to the other in a probe of two points. Micrographs of the 3-APTES coupled SOBM core-shell clay filler clearly show cloudy appearance, while FT-IR indicates 25% and 5% increases in fundamental vibrations band at 1014 cm−1 and 1435 cm−1, respectively. Furthermore, 3-APTES coupled core-shell clay was used to prepare epoxy composites and tested for mechanical properties. PMID:27355022

Experimental Study on Environment Friendly Tap Hole Clay for Blast Furnace

NASA Astrophysics Data System (ADS)

Siva kumar, R.; Mohammed, Raffi; Srinivasa Rao, K.

2018-03-01

Blast furnace (BF) is the best possible route of iron production available. Blast furnace is a high pressure vessel where iron ore is melted and liquid iron is produced. The liquid iron is tapped through the hole in Blast Furnace called tap hole. The tapped liquid metal flowing through the tap hole is plugged using a clay called tap hole clay. Tap hole clay (THC) is a unshaped refractory used to plug the tap hole. The tap hole clay extruded through the tap hole using a gun. The tap hole clay is designed to expand and plug the tap hole. The tap hole filled with clay is drilled using drill bit and the hole made through the tap hole to tap the liquid metal accumulated inside the furnace. The number of plugging and drilling varies depending on the volume of the furnace. The tap hole clay need to have certain properties to avoid problems during plugging and drilling. In the present paper tap hole clay properties in industrial use was tested and studied. The problems were identified related to tap hole clay manufacturing. Experiments were conducted in lab scale to solve the identified problems. The present composition was modified with experimental results. The properties of the modified tap hole clay were found suitable and useful for blast furnace operation with lab scale experimental results.

Development and Evaluation of a Contrast Sensitivity Perimetry Test for Patients with Glaucoma

PubMed Central

Hot, Aliya; Dul, Mitchell W.; Swanson, William H.

2008-01-01

Purpose To design a contrast sensitivity perimetry (CSP) protocol that decreases variability in glaucomatous defects while maintaining good sensitivity to glaucomatous loss. Methods Twenty patients with glaucoma and 20 control subjects were tested with a CSP protocol implemented on a monitor-based testing station. In the protocol 26 locations were tested over the central visual field with Gabor patches with a peak spatial frequency of 0.4 cyc/deg and a two-dimensional spatial Gaussian envelope, with most of the energy concentrated within a 4° circular region. Threshold was estimated by a staircase method. Patients and 10 age-similar control subjects were also tested on conventional automated perimetry (CAP), with the 24−2 pattern with the SITA Standard testing strategy. The neuroretinal rim area of the patients was measured with a retinal tomograph (Retina Tomograph II [HRT]; Heidelberg Engineering, Heidelberg, Germany). A Bland-Altman analysis of agreement was used to assess test–retest variability, compare depth of defect shown by the two perimetric tests, and investigate the relations between contrast sensitivity and neuroretinal rim area. Results Variability showed less dependence on defect depth for CSP than for CAP (z = 9.3, P < 0.001). Defect depth was similar for CAP and CSP when averaged by quadrant (r = 0.26, P > 0.13). The relation between defect depth and rim area was more consistent with CSP than with CAP (z = 9, P < 0.001). Conclusions The implementation of CSP was successful in reducing test–retest variability in glaucomatous defects. CSP was in general agreement with CAP in terms of depth of defect and was in better agreement than CAP with HRT-determined rim area. PMID:18378580

Preliminary report on the clay mineralogy of the Upper Devonian Shales in the southern and middle Appalachian Basin

USGS Publications Warehouse

Hosterman, John W.; Loferski, Patricia J.

1978-01-01

The distribution of kaolinite in parts of the Devonian shale section is the most significant finding of this work. These shales are composed predominately of 2M illite and illitic mixed-layer clay with minor amounts of chlorite and kaolinite. Preliminary data indicate that kaolinite, the only allogenic clay mineral, is present in successively older beds of the Ohio Shale from south to north in the southern and middle parts of the Appalachian basin. This trend in the distribution of kaolinite shows a paleocurrent direction to the southwest. Three well-known methods of preparing the clay fraction for X-ray diffraction analysis were tested and evaluated. Kaolinite was not identified in two of the methods because of layering due to differing settling rates of the clay minerals. It is suggested that if one of the two settling methods of sample preparation is used, the clay film be thin enough for the X-ray beam to penetrate the entire thickness of clay.

New polyelectrolyte complex from pectin/chitosan and montmorillonite clay.

PubMed

da Costa, Marcia Parente Melo; de Mello Ferreira, Ivana Lourenço; de Macedo Cruz, Mauricio Tavares

2016-08-01

A new nanocomposite hydrogel was prepared by forming a crosslinked hybrid polymer network based on chitosan and pectin in the presence of montmorillonite clay. The influence of clay concentration (0.5 and 2% wt) as well as polymer ratios (1:1, 1:2 and 2:1) was investigated carefully. The samples were characterized by different techniques: transmission and scanning electron microscopy, X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, swelling degree and compression test. Most samples presented swelling degree above 1000%, which permits characterizing them as superabsorbent material. Images obtained by transmission electron microscopy showed the presence of clay nanoparticles into hydrogel. The hydrogels' morphological properties were evaluated by scanning electron microscope in high and low-vacuum. The micrographs showed that the samples presented porous. The incorporation of clay produced hydrogels with differentiated morphology. Thermogravimetric analysis results revealed that the incorporation of clay in the samples provided greater thermal stability to the hydrogels. The compression resistance also increased with addition of clay. Copyright © 2016 Elsevier Ltd. All rights reserved.

A quantification model for the structure of clay materials.

PubMed

Tang, Liansheng; Sang, Haitao; Chen, Haokun; Sun, Yinlei; Zhang, Longjian

2016-07-04

In this paper, the quantification for clay structure is explicitly explained, and the approach and goals of quantification are also discussed. The authors consider that the purpose of the quantification for clay structure is to determine some parameters that can be used to quantitatively characterize the impact of clay structure on the macro-mechanical behaviour. According to the system theory and the law of energy conservation, a quantification model for the structure characteristics of clay materials is established and three quantitative parameters (i.e., deformation structure potential, strength structure potential and comprehensive structure potential) are proposed. And the corresponding tests are conducted. The experimental results show that these quantitative parameters can accurately reflect the influence of clay structure on the deformation behaviour, strength behaviour and the relative magnitude of structural influence on the above two quantitative parameters, respectively. These quantitative parameters have explicit mechanical meanings, and can be used to characterize the structural influences of clay on its mechanical behaviour.

Long-term recovery of PCB-contaminated surface sediments at the Sangamo-westonl Twelvemile Creek/lake Hartwell Superfund Site.

PubMed

Brenner, Richard C; Magar, Victor S; Ickes, Jennifer A; Foote, Eric A; Abbott, James E; Bingler, Linda S; Crecelius, Eric A

2004-04-15

Natural recovery of contaminated sediments relies on burial of contaminated sediments with increasingly clean sediments over time (i.e., natural capping). Natural capping reduces the risk of resuspension of contaminated surface sediments, and it reduces the potential for contaminant transport into the food chain by limiting bioturbation of contaminated surface or near-surface sediments. This study evaluated the natural recovery of surface sediments contaminated with polychlorinated biphenyls (PCBs) at the Sangamo-Weston/Twelvemile Creek/Lake Hartwell Superfund Site (Lake Hartwell), Pickens County, SC. The primary focus was on sediment recovery resulting from natural capping processes. Total PCB (t-PCB), lead-210 (210Pb), and cesium-137 (137Cs) sediment core profiles were used to establish vertical t-PCB concentration profiles, age date sediments, and determine surface sedimentation and surface sediment recovery rates in 18 cores collected along 10 transects. Four upgradient transects in the headwaters of Lake Hartwell were impacted by historical sediment releases from three upgradient sediment impoundments. These transects were characterized by silt/ clay and sand layering. The highest PCB concentrations were associated with silt/clay layers (1.8-3.5% total organic carbon (TOC)), while sand layers (0.05-0.32% TOC) contained much lower PCB concentrations. The historical sediment releases resulted in substantial burial of PCB-contaminated sediment in the vicinity of these four cores; each core contained less than 1 mg/kg t-PCBs in the surface sand layers. Cores collected from six downgradient Lake Hartwell transects consisted primarily of silt and clay (0.91-5.1% TOC) and were less noticeably impacted by the release of sand from the impoundments. Vertical t-PCB concentration profiles in these cores began with relatively low PCB concentrations at the sediment-water interface and increased in concentration with depth until maximum PCB concentrations were measured at approximately 30-60 cm below the sediment-water interface, ca. 1960-1980. Maximum t-PCB concentrations were followed by progressively decreasing concentrations with depth until the t-PCB concentrations approached the detection limit, where sediments were likely deposited before the onset of PCB use at the Sangamo-Weston plant. The sediments containing the maximum PCB concentrations are associated with the period of maximum PCB release into the watershed. Sedimentation rates averaged 2.1 +/- 1.5 g/(cm2 yr) for 12 of 18 cores collected. The 1994 Record of Decision cleanup requirement is 1.0 mg/kg; two more goals (0.4 and 0.05 mg/kg t-PCBs) also were identified. Average surface sedimentation requirements to meet the three goals were 1.4 +/- 3.7, 11 +/- 4.2, and 33 +/- 11 cm, respectively. Using the age dating results, the average recovery dates to meet these goals were 2000.6 +/- 2.7, 2007.4 +/- 3.5, and 2022.7 +/- 11 yr, respectively. (The 95% prediction limits for these values also are provided.) Despite the reduction in surface sediment PCB concentrations, PCB concentrations measured in largemouth bass and hybrid bass filets continue to exceed the 2.0 mg/kg FDA fish tolerance level.

Influence of Different Container Closure Systems and Capping Process Parameters on Product Quality and Container Closure Integrity (CCI) in GMP Drug Product Manufacturing.

PubMed

Mathaes, Roman; Mahler, Hanns-Christian; Roggo, Yves; Huwyler, Joerg; Eder, Juergen; Fritsch, Kamila; Posset, Tobias; Mohl, Silke; Streubel, Alexander

2016-01-01

Capping equipment used in good manufacturing practice manufacturing features different designs and a variety of adjustable process parameters. The overall capping result is a complex interplay of the different capping process parameters and is insufficiently described in literature. It remains poorly studied how the different capping equipment designs and capping equipment process parameters (e.g., pre-compression force, capping plate height, turntable rotating speed) contribute to the final residual seal force of a sealed container closure system and its relation to container closure integrity and other drug product quality parameters. Stopper compression measured by computer tomography correlated to residual seal force measurements.In our studies, we used different container closure system configurations from different good manufacturing practice drug product fill & finish facilities to investigate the influence of differences in primary packaging, that is, vial size and rubber stopper design on the capping process and the capped drug product. In addition, we compared two large-scale good manufacturing practice manufacturing capping equipment and different capping equipment settings and their impact on product quality and integrity, as determined by residual seal force.The capping plate to plunger distance had a major influence on the obtained residual seal force values of a sealed vial, whereas the capping pre-compression force and the turntable rotation speed showed only a minor influence on the residual seal force of a sealed vial. Capping process parameters could not easily be transferred from capping equipment of different manufacturers. However, the residual seal force tester did provide a valuable tool to compare capping performance of different capping equipment. No vial showed any leakage greater than 10(-8)mbar L/s as measured by a helium mass spectrometry system, suggesting that container closure integrity was warranted in the residual seal force range tested for the tested container closure systems. Capping equipment used in good manufacturing practice manufacturing features different designs and a variety of adjustable process parameters. The overall capping result is a complex interplay of the different capping process parameters and is insufficiently described in the literature. It remains poorly studied how the different capping equipment designs and capping equipment process parameters contribute to the final capping result.In this study, we used different container closure system configurations from different good manufacturing process drug product fill & finish facilities to investigate the influence of the vial size and the rubber stopper design on the capping process. In addition, we compared two examples of large-scale good manufacturing process capping equipment and different capping equipment settings and their impact on product quality and integrity, as determined by residual seal force. © PDA, Inc. 2016.

The effects of Tulsa's CAP Head Start program on middle-school academic outcomes and progress.

PubMed

Phillips, Deborah; Gormley, William; Anderson, Sara

2016-08-01

This study presents evidence pertinent to current debates about the lasting impacts of early childhood educational interventions and, specifically, Head Start. A group of students who were first studied to examine the immediate impacts of the Tulsa, Oklahoma, Community Action Project (CAP) Head Start program were followed-up in middle school, primarily as 8th graders. Using ordinary least squares and logistic regressions with a rich set of controls and propensity score weighting models to account for differential selection into Head Start, we compared students who had attended the CAP Head Start program and enrolled in the Tulsa Public Schools (TPS) as kindergarteners with children who also attended TPS kindergarten but had attended neither CAP Head Start nor the TPS pre-K program as 4-year-olds. CAP Head Start produced significant positive effects on achievement test scores in math and on both grade retention and chronic absenteeism for middle-school students as a whole; positive effects for girls on grade retention and chronic absenteeism; for white students on math test scores; for Hispanic students on math test scores and chronic absenteeism, and for students eligible for free lunches on math test scores, grade retention, and chronic absenteeism. We conclude that the Tulsa CAP Head Start program produced significant and consequential effects into the middle school years. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

[Comparison of expression of transforming growth factor-β1 in rat dental pulp during direct pulp capping with 2 capping agents].

PubMed

Zhang, Xiao-fang; Yao, Ya-peng; Kang, Hong-ying; Dong, Pei

2014-04-01

To examine and compare the expression of transforming growth factor-β1(TGF-β1) in rat dental pulp after direct pulp capping with calcium hydroxide (CH) and mineral trioxide aggregate (MTA). The model of direct dental pulp capping after first molars was established in 28 female Wistar rats with CH and MTA. The rats were sacrificed 1, 3, 5, 7, 14,21 and 28 days after direct pulp capping. TGF-β1 expression in pulp tissues were measured with immunohistochemical staining. The data was analyzed by Dunnett t test and paired t test with SPSS 13.0 software package. The results showed that no TGF-β1 expression was detected in the control group. After direct pulp capping with MTA, TGF-β1 expression gradually increased and reached peak expression on 5 day. TGF-β1 expression gradually decreased afterwards and reached normal on 21 day after direct pulp. TGF-β1 was mainly expressed in neutrophils, odontoblasts cells, vascular endothelial cells and fibroblasts. The expression of TGF-β1 was significantly different between 2 capping agents 1, 3, 5, 7, 14 days after direct pulp capping (P<0.05). The results suggest that TGF-β1 expression increases at first and then decreases after direct pulp capping. The type of capping agents has an impact on the expression of TGF-β1 after direct pulp capping. MTA enhances more TGFβ-1 expression than CH 1, 3, 5, 7 and 14 days after direct pulp capping. Supported by Science and Technology Plan Project of Liaoning Province (2009225001-2).

Unraveling the antibacterial mode of action of a clay from the Colombian Amazon.

PubMed

Londono, Sandra Carolina; Williams, Lynda B

2016-04-01

Natural antibacterial clays can inhibit growth of human pathogens; therefore, understanding the antibacterial mode of action may lead to new applications for health. The antibacterial modes of action have shown differences based on mineralogical constraints. Here we investigate a natural clay from the Colombian Amazon (AMZ) known to the Uitoto natives as a healing clay. The physical and chemical properties of the AMZ clay were compared to standard reference materials: smectite (SWy-1) and kaolinite (API #5) that represent the major minerals in AMZ. We tested model Gram-negative (Escherichia coli ATCC #25922) and Gram-positive (Bacillus subtilis ATCC #6633) bacteria to assess the clay's antibacterial effectiveness against different bacterial types. The chemical and physical changes in the microbes were examined using bioimaging and mass spectrometry of clay digests and aqueous leachates. Results indicate that a single dose of AMZ clay (250 mg/mL) induced a 4-6 order of magnitude reduction in cell viability, unlike the reference clays that did not impact bacterial survival. AMZ clay possesses a relatively high specific surface area (51.23 m(2)/g) and much higher total surface area (278.82 m(2)/g) than the reference clays. In aqueous suspensions (50 mg clay/mL water), soluble metals are released and the minerals buffer fluid pH between 4.1 and 4.5. We propose that the clay facilitates chemical interactions detrimental to bacteria by absorbing nutrients (e.g., Mg, P) and potentially supplying metals (e.g., Al) toxic to bacteria. This study demonstrates that native traditional knowledge can direct scientific studies.

Improved recombinant Api m 1- and Ves v 5-based IgE testing to dissect bee and yellow jacket allergy and their correlation with the severity of the sting reaction.

PubMed

Šelb, J; Kogovšek, R; Šilar, M; Košnik, M; Korošec, P

2016-04-01

No study has assessed the diagnostic sensitivity of rApi m 1 and rVes v 5 on Immulite testing system. To compare the diagnostic sensitivity of commercially available venom recombinant allergens between the currently available immunoassays [ImmunoCAP (CAP) and Immulite (LITE)] and establish their correlation with the severity of the sting reaction. This study evaluated 95 bee venom and 110 yellow jacket venom-allergic subjects. We measured the levels of sIgE to rApi m 1, rVes v 5 (LITE and CAP), rApi m 2 (LITE), rVes v 1 (CAP) and total IgE (CAP). Forty-nine healthy subjects served as controls. The diagnostic sensitivity of rApi m 1 and rVes v 5 was significantly higher with the LITE than with the CAP system (71% vs. 88% and 82% vs. 93%). The specificity of both assays for both allergens was between 94% and 98%. Twenty-nine patients that tested negative for rApi m 1 or rVes v 5 with CAP were positive with LITE, but none of the patients that tested negative with LITE were positive with CAP. The positive values of rApi m 1 and rVes v 5 were on average 2.7 and 2.3 times higher, with the LITE than with the CAP system. The combination of rApi m 1 and rApi m 2 (LITE) and the combination of rVes v 5 (LITE) and rVes v 1 (CAP) almost matched the sensitivity of native venoms (95% and 97%, respectively), whereas the diagnostic sensitivity of the combination of rVes v 5 and rVes v 1 (CAP) did not reach the sensitivity of rVes v 5 (LITE) alone (90% vs. 93%). IgE levels to venom recombinants and total IgE did not correlate with the severity of sting reaction. The use of rApi m 1 and rVes v 5 with the LITE system significantly enhanced diagnostic utility of venom recombinants and should improve the dissection of bee and yellow jacket venom allergy. © 2015 John Wiley & Sons Ltd.

Breakdown Voltage of Thermoplastics with Clay Nanometer-Sized Fillers (Postprint)

DTIC Science & Technology

2008-12-01

of clay nanofillers. Low density polyethylene ( LDPE ) is a mechanically tough, inexpensive polymer used heavily in industry. Numerous studies have...A blend of LDPE grafted with maleic anhydride ( LDPE -g- MA) is tested in this work for improved electrical properties with clay addition. The...LLDPE) copolymer with octene. LLDPE improves over regular LDPE in a number of mechanical properties, though it has a higher production cost. A

Properties of Base Stocks Obtained from Used Engine Oils by Acid/Clay Re-refining (Proprietes des Stocks de Base Obtenus par Regeneration des Huiles a Moteur Usees par le Procede de Traitement a l’Acide et a la Terre),

DTIC Science & Technology

1980-09-01

Research Conseil national Council Canada de recherches Canada LEY EL < PROPERTIES OF BASE STOCKS OBTAINED FROM USED ENGINE OILS BY ACID /CLAY RE-REFINING DTIC...MECHANICAL ENGINEERING REPORT Canad NC MP75 NRC NO. 18719 PROPERTIES OF BASE STOCKS OBTAINED FROM USED ENGINE OILS BY ACID /CLAY RE-REFINING (PROPRIETES...refined Base Stock ..................................... 10 3 Physical Test Data of Acid /Clay Process - Re-refined Base Stock Oils ............ 11 4

Developing Basic Mathematical Skills of Pre-School Children by Using Plasticized Clay

ERIC Educational Resources Information Center

Chumark, Charung; Puncreobutr, Vichian

2016-01-01

The main objective of this research was to study the development of basic mathematical skills in preschool children by using plasticized clay. A pre-test and post-test design was adopted for the study to compare the difference before and after the art activity. The experimental group of 15 preschool children of 3-4 years old, attending…

Artificial recharge to a freshwater-sensitive brackish-water sand aquifer, Norfolk, Virginia

USGS Publications Warehouse

Brown, Donald L.; Silvey, William Dudley

1977-01-01

Fresh water was injected into a brackish-water sand for storage and retrieval. The initial injection rate of 400 gpm decreased to 70 gpm during test 3. The specific capacity of the well decreased also, from 15.4 to 0.93 gpm. Current-meter surveys indicated uniform reduction in hydraulic conductivity of all contributing zones in the aquifer. Hydraulic and chemical data indicate this was caused by dispersion of the interstitial clay upon introduction of the calcium bicarbonate water into the sodium chloride bearing sand aquifer. The clay dispersion also caused particulate rearrangement and clogging of well screen. A pre-flush of 0.2 N calcium chloride solution injected in front of the fresh water at the start of test 4 stabilized the clay. However, it did not reverse the particulate clogging that permanently reduced permeability and caused sanding during redevelopment. Clogging can be prevented by stabilization of the clay using commercially available trivalent aluminum compounds. Test 1 and test 2 showed that 85 percent of the water injected can be recovered, and the water meets U.S. Public Health Standards. Storage of fresh water in a brackish-water aquifer appears feasible provided proper control measures are used. (Woodard-USGS)

Graphite composite truss welding and cap section forming subsystems. Volume 1: Executive summary. [large space structures

NASA Technical Reports Server (NTRS)

1980-01-01

A rolltrusion process was developed for forming of a hybrid, single-ply woven graphite and glass fiber cloth, impregnated with a polysulfone resin and coated with TI02 pigmented P-1700 resin into strips for the on-orbit fabrication of triangular truss segments. Ultrasonic welding in vacuum showed no identifiable effects on weld strength or resin flow characteristics. An existing bench model cap roll forming machine was modified and used to roll form caps for the prototype test truss and for column test specimens in order to test local buckling and torsional instability characteristics.

Effects of cold atmospheric plasma on mucosal tissue culture

NASA Astrophysics Data System (ADS)

Welz, Christian; Becker, Sven; Li, Yang-Fang; Shimizu, Tetsuji; Jeon, Jin; Schwenk-Zieger, Sabina; Thomas, Hubertus M.; Isbary, Georg; Morfill, Gregor E.; Harréus, Ulrich; Zimmermann, Julia L.

2013-01-01

Thermal plasmas have been commonly used in medical applications such as plasma ablation and blood coagulation. Newer developments show that plasmas can be generated with ion temperatures close to room temperature: these non-thermal or so-called cold atmospheric plasmas (CAPs) therefore open up a wide range of further biomedical applications. Based on the understanding of the bactericidal, virucidal and fungicidal properties of CAPs, information about the effects of CAP on mucosal cells and tissue is still lacking. Therefore this study focuses on the interaction of CAP with healthy head and neck mucosal cells on a molecular level. To analyse this interaction in detail, fresh tissue samples from healthy nasal and pharyngeal mucosa were harvested during surgery, assembled to a three-dimensional tissue culture model (mini organ cultures) and treated with CAP for different treatment times. Effects on the viability, necrosis induction and mutagenic activity were evaluated with the trypan blue exclusion test, Annexin-V/PI staining and alkaline microgel electrophoresis (comet assay). Trypan blue exclusion test revealed that the CAP treatment significantly decreases the cell viability for all tested treatment times (5, 10, 30, 60 and 120 s p < 0.05), but only a treatment time of 120 s showed a cytotoxic effect as the viability dropped below 90%. Annexin-V/PI staining revealed a significant increase in necrosis in CAP treated pharyngeal tissue cultures for treatment times of 60 and 120 s (p < 0.05). For nasal tissue this effect was already detected for a 30 s treatment (p < 0.05). Comet assay analysis showed no mutagenic effects after exposure to CAP.

Laterally loaded pile cap connections.

DOT National Transportation Integrated Search

2010-08-01

This study investigated the moment capacity and load-displacement response of the pile-to-cap connection details. Lateral load tests were conducted on four pile caps (3 ft H x 3 ft W x 6.5 ft L) with two 40 foot-long steel pipe piles (12.75 inch OD) ...

The methodology of choice Cam-Clay model parameters for loess subsoil

NASA Astrophysics Data System (ADS)

Nepelski, Krzysztof; Błazik-Borowa, Ewa

2018-01-01

The paper deals with the calibration method of FEM subsoil model described by the constitutive Cam-Clay model. The four-storey residential building and solid substrate are modelled. Identification of the substrate is made using research drilling, CPT static tests, DMT Marchetti dilatometer, and laboratory tests. Latter are performed on the intact soil specimens which are taken from the wide planning trench at the depth of foundation. The real building settlements was measured as the vertical displacement of benchmarks. These measurements were carried out periodically during the erection of the building and its operation. Initially, the Cam Clay model parameters were determined on the basis of the laboratory tests, and later, they were corrected by taking into consideration numerical analyses results (whole building and its parts) and real building settlements.

Creep and Sliding in Clay Slopes: Mutual Effects of Interlayer Swelling and Ice Jacking.

DTIC Science & Technology

1983-08-24

project, swelling and freezing, have been treated as well. The extent of swell heave of the montmorillonite clay under investigation depends on the...the amount of clay size particles: up to 70% and the amount of montmorillonite : up to 35%. 1.2. Grain Size Distribution Twelve hydrometer tests were...in physical conditions and exhibit swelling again upon subsequent wetting. Another important swelling parameter is the montmorillonite content, that

Impact of clay minerals on sulfate-reducing activity in aquifers

USGS Publications Warehouse

Wong, D.; Suflita, J.M.; McKinley, J.P.; Krumholz, L.R.

2004-01-01

Previous studies have shown that sulfate-reduction activity occurs in a heterogeneous manner throughout the terrestrial subsurface. Low-activity regions are often observed in the presence of clay minerals. Here we report that clays inhibit sulfate reduction activity in sediments and in a pure culture of Desulfovibriovulgaris. Clay minerals including bentonite and kaolinite inhibited sulfate reduction by 70–90% in sediments. Intact clays and clay colloids or soluble components, capable of passing through a 0.2-µm filter, were also inhibitory to sulfate-reducing bacteria. Other adsorbent materials, including anion or cation exchangers and a zeolite, did not inhibit sulfate reduction in sediments, suggesting that the effect of clays was not due to their cation-exchange capacity. We observed a strong correlation between the Al2O3content of clays and their relative ability to inhibit sulfate reduction in sediments (r2 = 0.82). This suggested that inhibition might be a direct effect of Al3+ (aq) on the bacteria. We then tested pure aluminum oxide (Al2O3) and showed it to act in a similar manner to clay. As dissolved aluminum is known to be toxic to a variety of organisms at low concentrations, our results suggest that the effects of clay on sulfate-reducing bacteria may be directly due to aluminum. Thus, our experiments provide an explanation for the lack of sulfate-reduction activity in clay-rich regions and presents a mechanism for the effect.

Effects of clay dispersion on aquifer storage and recovery in coastal aquifers

USGS Publications Warehouse

Konikow, Leonard F.; August, L.L.; Voss, C.I.

2001-01-01

Cyclic injection, storage, and withdrawal of freshwater in brackish aquifers is a form of aquifer storage and recovery (ASR) that can beneficially supplement water supplies in coastal areas. A 1970s field experiment in Norfolk, Virginia, showed that clay dispersion in the unconsolidated sedimentary aquifer occurred because of cation exchange on clay minerals as freshwater displaced brackish formation water. Migration of interstitial clay particles clogged pores, reduced permeability, and decreased recovery efficiency, but a calcium preflush was found to reduce clay dispersion and lead to a higher recovery efficiency. Column experiments were performed in this study to quantify the relations between permeability changes and clay mineralogy, clay content, and initial water salinity. The results of these experiments indicate that dispersion of montmorillonite clay is a primary contributor to formation damage. The reduction in permeability by clay dispersion may be expressed as a linear function of chloride content. Incorporating these simple functions into a radial, cross-sectional, variable-density, ground-water flow and transport model yielded a satisfactory simulation of the Norfolk field test - and represented an improvement over the model that ignored changes in permeability. This type of model offers a useful planning and design tool for ASR operations in coastal clastic aquifer systems.

A front-end wafer-level microsystem packaging technique with micro-cap array

NASA Astrophysics Data System (ADS)

Chiang, Yuh-Min

2002-09-01

The back-end packaging process is the remaining challenge for the micromachining industry to commercialize microsystem technology (MST) devices at low cost. This dissertation presents a novel wafer level protection technique as a final step of the front-end fabrication process for MSTs. It facilitates improved manufacturing throughput and automation in package assembly, wafer level testing of devices, and enhanced device performance. The method involves the use of a wafer-sized micro-cap array, which consists of an assortment of small caps micro-molded onto a material with adjustable shapes and sizes to serve as protective structures against the hostile environments during packaging. The micro-cap array is first constructed by a micromachining process with micro-molding technique, then sealed to the device wafer at wafer level. Epoxy-based wafer-level micro cap array has been successfully fabricated and showed good compatibility with conventional back-end packaging processes. An adhesive transfer technique was demonstrated to seal the micro cap array with a MEMS device wafer. No damage or gross leak was observed while wafer dicing or later during a gross leak test. Applications of the micro cap array are demonstrated on MEMS, microactuators fabricated using CRONOS MUMPS process. Depending on the application needs, the micro-molded cap can be designed and modified to facilitate additional component functions, such as optical, electrical, mechanical, and chemical functions, which are not easily achieved in the device by traditional means. Successful fabrication of a micro cap array comprised with microlenses can provide active functions as well as passive protection. An optical tweezer array could be one possibility for applications of a micro cap with microlenses. The micro cap itself could serve as micro well for DNA or bacteria amplification as well.

Use of neoprene pads in testing concrete cylinders : final report.

DOT National Transportation Integrated Search

1982-01-01

This study investigated the feasibility of using neoprene pads confined by steel end caps instead of sulfur-mortar caps in compressive strength tests on concrete cylinders. The 1/2 in. (13 mm) thick neoprene pads had a 50 durometer hardness and were ...

Hardware Design and Testing of SUPERball, A Modular Tensegrity Robot

NASA Technical Reports Server (NTRS)

Sabelhaus, Andrew P.; Bruce, Jonathan; Caluwaerts, Ken; Chen, Yangxin; Lu, Dizhou; Liu, Yuejia; Agogino, Adrian K.; SunSpiral, Vytas; Agogino, Alice M.

2014-01-01

We are developing a system of modular, autonomous "tensegrity end-caps" to enable the rapid exploration of untethered tensegrity robot morphologies and functions. By adopting a self-contained modular approach, different end-caps with various capabilities (such as peak torques, or motor speeds), can be easily combined into new tensegrity robots composed of rods, cables, and actuators of different scale (such as in length, mass, peak loads, etc). As a first step in developing this concept, we are in the process of designing and testing the end-caps for SUPERball (Spherical Underactuated Planetary Exploration Robot), a project at the Dynamic Tensegrity Robotics Lab (DTRL) within NASA Ames's Intelligent Robotics Group. This work discusses the evolving design concepts and test results that have gone into the structural, mechanical, and sensing aspects of SUPERball. This representative tensegrity end-cap design supports robust and repeatable untethered mobility tests of the SUPERball, while providing high force, high displacement actuation, with a low-friction, compliant cabling system.

The Role of NREM Sleep Instability in Child Cognitive Performance

PubMed Central

Bruni, Oliviero; Kohler, Mark; Novelli, Luana; Kennedy, Declan; Lushington, Kurt; Martin, James; Ferri, Raffaele

2012-01-01

Study Objectives: Based on recent reports of the involvement of cyclic alternating pattern (CAP) in cognitive functioning in adults, we investigated the association between CAP parameters and cognitive performance in healthy children. Design: Polysomnographic assessment and standardized neurocognitive testing in healthy children. Settings: Sleep laboratory. Participants: Forty-two children aged 7.6 ± 2.7 years, with an even distribution of body mass percentile (58.5 ± 25.5) and SES reflective of national norms. Measurements: Analysis of sleep macrostructure following the R&K criteria and of cyclic alternating pattern (CAP). The neurocognitive tests were the Stanford Binet Intelligence Scale (5th edition) and a Neuropsychological Developmental Assessment (NEPSY) Results: Fluid reasoning ability was positively associated with CAP rate, particularly during SWS and with A1 total index and A1 index in SWS. Regression analysis, controlling for age and SES, showed that CAP rate in SWS and A1 index in SWS were significant predictors of nonverbal fluid reasoning, explaining 24% and 22% of the variance in test scores, respectively. Conclusion: This study shows that CAP analysis provides important insights on the role of EEG slow oscillations (CAP A1) in cognitive performance. Children with higher cognitive efficiency showed an increase of phase A1 in total sleep and in SWS Citation: Bruni O; Kohler M; Novelli L; Kennedy D; Lushington K; Martin J; Ferri R. The role of NREM sleep instability in child cognitive performance. SLEEP 2012;35(5):649-656. PMID:22547891

Tensile and burning properties of clay/phenolic/GF composite and its application

NASA Astrophysics Data System (ADS)

Diharjo, Kuncoro; Armunanto, V. Bram; Kristiawan, S. Adi

2016-03-01

Composite material has been widely used in automotive due to its properties can be improved by combining with reinforcement, like fiber and particle to enhance mechanical properties and burning resistance. This study aims to investigate the tensile and burning properties of hybrid composite combining glass fiber and clay in phenolic resin. The clay was produced from roof tile rejected by tile industries in Sokka, Kebumen, Indonesia. The composite was made using a press mold method for different number of laminates and orientation of woven-roving-glass-fiber/ WRGF (0/90 and ±45), and the total volume fraction of fiber and clay is constant 40%. The specimens were tested using universal testing machine for tensile properties and burning tests apparatus for burning resistance (time to ignite/ TTI and burning rate/ BR). The enhancing of the Clay/Penolic/GF composite can be performed by the increasing of GF laminates, and the composite with 0/90 orientation of WRGF has higher tensile strength and modulus compared to that with ±45 orientation of WRGF. Both composite with 0/90 and ±45 orientation of WRGF have similar burning resistance (TTI and BR) and the composite containing 13 laminates of WR-GF shows the best burning resistance. According to these properties, this composite has good opportunity to be applied as car body panels or other structure in industries due to save weight and high burning resistance.

Mechanical Property Allowables Generated for the Solid Rocket Booster Composite Note Cap

NASA Technical Reports Server (NTRS)

Hodge, A. J.

2000-01-01

Mechanical property characterization was performed on AS4/3501-6 graphite/epoxy and SC350G syntactic foam for the SRB Composite Nose Cap Shuttle Upgrades Project. Lamina level properties for the graphite/epoxy were determined at room temperature, 240 F, 350 F, 480 F, 600 F, and 350 F after a cycle to 600 F. Graphite/epoxy samples were moisture conditioned prior to testing. The syntactic foam material was tested at room temperature, 350 F, and 480 F. A high-temperature test facility was developed at MSFC. Testing was performed with quartz lamp heaters and high resistance heater strips. The thermal history profile of the nose cap was simulated in order to test materials at various times during launch. A correlation study was performed with Southern Research Institute to confirm the test methodology and validity of test results. A-basis allowables were generated from the results of testing on three lots of material.

Comparsion of an immunochromatographic strip with ELISA for simultaneous detection of thiamphenicol, florfenicol and chloramphenicol in food samples.

PubMed

Guo, Lingling; Song, Shanshan; Liu, Liqiang; Peng, Juan; Kuang, Hua; Xu, Chuanlai

2015-09-01

Rapid and sensitive indirect competitive enzyme-linked immunosorbent assays (ic-ELISA) and gold nanoparticle immunochromatographic strip tests were developed to detect thiamphenicol (TAP), florfenicol (FF) and chloramphenicol (CAP) in milk and honey samples. The generic monoclonal antibody for TAP, FF and CAP was prepared based on a hapten [D-threo-1-(4-aminophenyl)-2- dichloroacetylamino-1,3-propanediol], and the haptenwas linked to a carrier protein using the diazotization method. After the optimization of several parameters (coating, pH, sodium chloride content and methanol content), the ic-ELISA was established. The quantitative working range for TAP was 0.11-1.36 ng/mL, with an IC50 of 0.39 ng/mL. The optimized ELISA showed cross-reactivity to CAP (300%) and FF (15.6%), with IC50 values of 0.13 and 2.5 ng/mL, respectively. The analytical recovery of TAP, FF and CAP in milk and honey samples in the ic-ELISA ranged from 81.2 to 112.9%. Based on this monoclonal antibody, a rapid and sensitive immunochromatographic test strip was also developed. This strip had a detection limit of 1 ng/mL for TAP, FF and CAP in milk and honey samples. Moreover, the test was completed within 10 min. Our results showed that the proposed ic-ELISA and immunochromatographic test strip method are highly useful screening tools for TAP, FF and CAP detection in milk and honey samples. Copyright © 2015 John Wiley & Sons, Ltd.

A gel-based visual immunoassay for non-instrumental detection of chloramphenicol in food samples.

PubMed

Yuan, Meng; Sheng, Wei; Zhang, Yan; Wang, Junping; Yang, Yijin; Zhang, Shuguang; Goryacheva, Irina Yu; Wang, Shuo

2012-11-02

A gel-based non-instrumental immuno-affinity assay was developed for the rapid screening of chloramphenicol (CAP) in food samples with the limit of detection (LOD) of 1 μg L(-1). The immuno-affinity test column (IATC) consisted of a test layer containing anti-CAP antibody coupled gel, and a control layer with anti-HRP antibody coupled gel. Based on the direct competitive immuno-reaction and the horseradish peroxidase enzymatic reaction, the test results could be evaluated visually. Basically, blue color development represented the negative results, while the absence of color development represented the positive results. In this study, CAP spiked samples of raw milk, pasteurized milk, UHT milk, skimmed milk powder, acacia honey, date honey, fish and shrimp were tested. Little or none sample pretreatment was required for this assay. The whole procedure was completed within 10min. In conclusion, the gel-based immuno-affinity test is a simple, rapid, and promising on-site screening method for CAP residues in food samples, with no instrumental requirement. Copyright © 2012 Elsevier B.V. All rights reserved.

Compaction and Plasticity Comparative Behaviour of Soft Clay Treated with Coarse and Fine Sizes of Ceramic Tiles

NASA Astrophysics Data System (ADS)

Al-Bared, Mohammed Ali Mohammed; Marto, Aminaton; Sati Hamonangan Harahap, Indra; Kasim, Fauziah

2018-03-01

Recycled blended ceramic tiles (RBT) is a waste material produced from ceramic tile factories and construction activities. RBT is found to be cost effective, sustainable, environmental-friendly and has the potential to be used as an additive in soft soil stabilization. Recent reports show that massive amounts of RBT are dumped into legal or illegal landfills every year consuming very large spaces and creating major environmental problems. On the other hand, dredged marine clay obtained from Nusajaya, Johor, Malaysia has weak physical and engineering characteristics to be considered as unsuitable soft soil that is usually excavated, dumped into landfills and replaced by stiff soil. Hence, this study investigates the suitability of possible uses of RBT to treat marine clay. Laboratory tests included Standard proctor tests and Atterberg limits tests. The plasticity of marine clay was evaluated by adding 10%, 20%, 30% and 40% of 0.3 mm RBT. In addition, the compaction behaviour of treated marine clay was compared by adding two different sizes (0.3 mm and 1.18 mm diameter) of RBT. For both coarse and fine sizes of RBT, 10%, 20%, 30% and 40% of the dry weight of the soft clay were added. The mixture of each combination was examined in order to evaluate the Maximum Dry Density (MDD) and the optimum moisture content (OMC) for the treated soft clay. MDD and OMC for soft untreated samples were 1.59 Mg/m3 and 22%, respectively. Treated samples with 10%, 20%, 30% and 40% of 0.30 mm size RBT resulted in a significant reduction of OMC ranged from 19 to 15% while MDD resulted in increment ranged from 1.69 to 1.77 Mg/m3. In addition, samples treated with 10%, 20%, 30% and 40% of 1.18 mm size RBT resulted in major reduction of OMC ranged from 15 to 13.5% while MDD increased effectively from 1.75 to 1.82 Mg/m3. For all mix designs of soft clay-RBT, MDD was gradually increasing and OMC was sharply reducing with further increments of both sizes of RBT.

Comparative characterization of the quaternary deposits of Northwest Peninsular Malaysia by wash boring and CPTU site investigation methods

NASA Astrophysics Data System (ADS)

Selamat, Mohamad R.; Rosli, Ros N.; Ramli, Muhd H.; Azmi, Mastura; Kumaravelu, Prakash; Govindasamy, Darvintharen

2017-10-01

A site investigation by wash boring method was carried out in the compound of the Engineering Campus, Universiti Sains Malaysia, in Northwest Peninsular Malaysia. The subsurface soils of the region are known to be comprised of quaternary deposits including the prominent marine clays of the Gula formation. The conventional Standard Penetration Test, or SPT, was carried out for every 1.5m depth. The 18 disturbed samples collected were tested for grain size distribution, Atterberg limits, and specific gravity; and categorized according to the unified soil classification system. The results indicate low SPT numbers, or SPTN, i.e. SPTN<4 for depths lesser than 10m, slightly high SPTN, i.e. 4≤SPTN≤8 for depths between 10 and 12m, and very high SPTN, i.e. SPTN>8 for depths deeper than 12m. Samples from shallower than 12m were mostly classified as low plasticity clay, or CL, which represents the soft marine clay while the underlying materials were mostly sands, namely poorly graded sand, or SP, silty sand, or SM, clayey sand, or SC, and well graded sand, or SW. Another site investigation by the CPTU method was also carried out 5m from the wash boring position, penetrating the entire soft clay stratum, thus giving another marine clay characterization in addition to the one given by the first method. The CPTU results generally gave SPTN≤2 for depths lesser than 8m, 2≤;SPTN≤4 for depths between 8 and 12m, and SPTN=23 at 12.5m, where the CPTU test terminated. The CPTU method classified the soft materials as sensitive fine grains, clays, and clayey silts to silty clays. Thus the CPTU results did not agree very well with the conventional wash boring SPT results in terms of the SPTN obtained. Nevertheless both methods equally identified the prominent presence of the soft marine clay stratum in the top 12.5m and the underlying strong sandy bed with higher bearing capacity values.

Sensitivity of genera Porphyromonas and Prevotella to the bactericidal action of C-terminal domain of human CAP18 and its analogues.

PubMed

Isogai, E; Isogai, H; Matuo, K; Hirose, K; Kowashi, Y; Okumuara, K; Hirata, M

2003-10-01

This paper reports the effect of the synthesized 27-amino acid sequence in the C-terminal domain of human CAP18 (hCAP18), a human cationic antibacterial protein or cathelicidin, on certain strains belonging to the genera Porophyromonas and Prevotella. The domain binds lipopolysaccharides (LPS) from Porophyromonas gingivalis and Porophyromonas circumdentaria as well as enterobacterial LPS. Two analogues of hCAP18, designated LL/CAP18 and FF/CAP18, were also tested to determine whether additional activity was obtained. The analogue peptides replaced with hydrophobic and cationic amino acid residues showed more potent bactericidal and LPS-binding activities than the original one.

Preparation and Characterization of a Superparamagnetic Polymer Nanocomposite

NASA Astrophysics Data System (ADS)

Brenner, N.; Isseroff, R.; Rafailovich, M.; Rudomen, G.; Gambino, R.; Liang, S. S.; Sunil, D.; Si, M.; Collazo, L.; Pernodet, N.; Fang, X.

2006-03-01

Fe(CO)5 decomposition produced ferro- and superparamagnetic polymer nanocomposites. Fe(CO)5 and Cloisite 20A clay were combined in a closed vial for 12 hours, then opened to air for 2 hours. Mössbauer analysis indicated formation of Fe2O3 on clay; mass analysis indicated 12% Fe in clay. A Brabender mixed Fe2O3/clays with PMMA and EVA at ratios by mass of 9:4:36 and 1:1:4 respectively (Fe(CO)5:clay:polymer). TEM displayed Fe2O3 nanoparticles, 3.3 ^+ 0.8 nm in diameter, adsorbed on exfoliated clay platelet surfaces in polymer matrices. VSM data indicated superparamagnetism with moments of 510.3 emu/g(Fe2O3) (PMMA) and 8.46 emu/g(Fe2O3) (EVA). DMA showed 37% decreased dynamic modulus (EVA) and 11% (PMMA) due to Fe2O3. TGA indicated PMMA stability to 400^oC (9.3% mass residual) and EVA to 435^oC (11% mass residual). Cell adhesion tests showed Fe2O3/clay enhanced proliferation, promising applications in bone implants.

PEP Talk: Prostate Education Program, "Cutting Through the Uncertainty of Prostate Cancer for Black Men Using Decision Support Instruments in Barbershops".

PubMed

Frencher, Stanley K; Sharma, Arun K; Teklehaimanot, Senait; Wadzani, Dennis; Ike, Ijeoma E; Hart, Alton; Norris, Keith

2016-09-01

The objective of this study was to investigate the effectiveness of using decision support instruments (DSI) to assist African-American (AA) men in making a prostate cancer (CaP) screening decision. This nonrandomized pretest-posttest comparison study assessed two DSI that were either culturally tailored or culturally nonspecific. CaP knowledge, intention to screen, and preferences were assessed before and after exposure to DSI using a convenience sample of 120 AA men aged 40 years and above. Participants interested in screening were referred to healthcare providers through a community-based patient navigator to obtain prostate-specific antigen (PSA) testing. We followed up 3 months after to determine if participants screened for CaP. CaP knowledge increased following exposure to both DSI in equivalent proportions. While similar proportions of men ultimately intended on having a PSA test following both DSI, bivariate analysis revealed that the culturally tailored DSI demonstrated a statistically significant increase in intention to screen. Participants' degree of certainty in their decision-making process with regard to CaP screening increased following the culturally tailored DSI (p < .001). The majority of participants planned on discussing CaP screening with a healthcare provider upon completion of the study. Barbershop-based health education can change the knowledge, preferences, intentions, and behaviors of this at-risk population. At 3 months follow-up, half (n = 58) of the participants underwent PSA testing, which led to the diagnosis of CaP in one participant. Community-led interventions for CaP, such as cluster-randomized designs in barbershops, are needed to better assess the efficacy of DSI in community settings.

Allergen Chip Diagnosis for Soy-Allergic Patients: Gly m 4 as a Marker for Severe Food-Allergic Reactions to Soy

PubMed Central

Berneder, M.; Bublin, M.; Hoffmann-Sommergruber, K.; Hawranek, T.; Lang, R.

2016-01-01

Background Gly m 5 and Gly m 6 are known to induce severe reactions in soy-allergic patients. For birch pollen (BP)-allergic patients, the Bet v 1 homologous allergen Gly m 4 is also a potential trigger of generalized severe reactions upon soy consumption. Therefore, reliable component-resolved diagnosis of soy allergy is needed. Methods IgE reactivity from sera of 20 patients from a BP environment with reported soy allergy was assessed. Skin prick tests (SPT) with BP and soy drink were performed. Specific IgE for BP, soy, Bet v 1 and Gly m 4 was analyzed by ImmunoCAP. In addition, ISAC microarray profiling was performed. Results Nineteen of 20 patients were BP allergic (positive SPT and/or CAP results for BP extract and Bet v 1). Eighteen soy-allergic patients were tested positive with soy drink in SPT. Soy CAP results were negative in the majority of tests (15/20), whereas 19/20 sera had specific IgE to Gly m 4. In the microarray approach, 14/20 sera displayed Gly m 4-specific IgE, the additional 6 sera had IgE levels below 0.3 ISAC standardized units. The BP-negative serum had Gly m 5- and Gly m 6-specific IgE which correlated with positive soy ImmunoCAP. Conclusions Soy sensitization detected by SPT and Gly m 4 ImmunoCAP were in good qualitative agreement with ISAC results. Soy ImmunoCAP was only specific for Gly m 5 and Gly m 6 sensitization. Gly m 4 ImmunoCAP has a higher sensitivity than ImmunoCAP ISAC. In this patient cohort, Gly m 4 sensitization was linked to the development of severe and generalized allergic reactions upon soy consumption. PMID:23548307

Prostate cancer survivors as community health educators: implications for informed decision making and cancer communication.

PubMed

Vijaykumar, Santosh; Wray, Ricardo J; Jupka, Keri; Clarke, Ryan; Shahid, Mellve

2013-12-01

Recent evidence questioning the effectiveness of prostate-specific antigen testing leave community-based prostate cancer (CaP) outreach programs with a dilemma between promoting screening and highlighting screening risks. CaP survivors are uniquely positioned to address this problem by drawing upon real-life experiences to share nuanced information and perspectives. While CaP survivors have historically been incorporated into outreach programs, little is known about their impact on psychosocial outcomes and their effectiveness compared to professional health educators. This study addressed these gaps through a quasi-experimental design where African American men attended a CaP screening session conducted by a health educator (HE) or survivor educator (SV). The presentation included prostate cancer statistics, CaP information, and descriptions of CaP screening tests. SV were encouraged to bolster their presentations with personal stories whereas HE maintained fidelity to the curriculum content. All participants completed pre- and post-test questionnaires. Our sample comprised a total of 63 participants (HE group = 32; SV group = 31) with an age range of 40-70 years. Decision self-efficacy increased significantly in the SV group (p = 0.01) whereas perceived screening risks reduced significantly in the HE group (p < 0.001). No significant changes were found in knowledge, subjective norms, outcome expectancies, and screening benefits. Survivor educators were found to have significantly greater appeal (p = 0.03), identification with audience (p = 0.01), and liking (p = 0.03). Training CaP survivors as health educators might be a viable strategy for community-based cancer communication efforts confronted by the CaP screening controversy. We discuss conceptual and programmatic implications of our findings and present directions for future research.

Nonlinear behavior of PP/PS blends with and without clay under large amplitude oscillatory shear (LAOS) flow

NASA Astrophysics Data System (ADS)

Salehiyan, Reza; Song, Hyeong Yong; Hyun, Kyu

2015-05-01

Dynamic oscillatory measurement, i.e., small amplitude oscillatory shear (SAOS) and large amplitude oscillatory shear (LAOS) test was used to investigate linear and non-linear viscoelastic properties of Polypropylene (PP)/Polystyrene (PS) blends with and without 5 wt.% clay (C20A). Fourier transform (FT-Rheology), Lissajous curves and stress decomposition methods were used to analyze non-linear responses under LAOS flow. Composition effects of blends were investigated prior to compatibilization effects. Elevated concentrations of dispersed phase (PS) increased the moduli G'(ω) from SAOS test and G*( γ 0) from LAOS test of the blends as well as strain thinning behavior. Interestingly, addition of 5 wt.% clay (C20A) boosted moduli of the blends as well as led to similar strain thinning behaviors among the PP/PS/C20A blends, except for the (90/10) PP/PS blend. The latter did not show improved rheological properties despite morphological improvements, as shown by SEM. Results from SEM and improved rheological properties of PP/PS/C20A blends revealed the compatibilization effects of clay (C20A) particles regardless of size reduction mechanisms. Third relative intensities ( I 3/1) from FT-rheology were found to be sensitive to clay (C20A) additions for the (70/30) and (30/70) PP/PS blends. Similarly, Lissajous curves could detect changes upon clay (C20A) addition, specifically at lower strain amplitudes whereupon addition of 5 wt.% clay resulted in the closed loops of Lissajous curves showing a more ellipsoidal shape due to increased elasticity in the blends. However, detection of these changes at larger strain amplitudes was more challenging. Therefore, stress decomposition (SD) method was applied for more precise characterization as it decomposes the total stress (σ) into elastic stress (σ') and viscous stress (σ″). Using SD method, elastic stress was more distorted, especially, strain hardening, while the total stress response remained almost unchanged at larger strain amplitudes.

Degradation of Nitrobenzene Using Bio-Reduced Fe-Clays: Progress Towards the Development of an in-situ Groundwater Remediation Technology

NASA Astrophysics Data System (ADS)

White, M. L.; Fialips, C. I.

2008-12-01

Clay minerals are widely used in agricultural, industrial and environmental engineering applications due to their specific physical and chemical properties and their high abundance in soils in sediments. Currently however, Fe-bearing clays are not widely exploited in these applied fields. Fe-rich smectites, such as nontronite, can contain up to 20wt% of Fe2O3 as structural Fe(III) and if a suitable electron donor is available, this Fe(III) can be utilized by Fe-reducing bacteria as a terminal electron acceptor. When reduced, the overall reactivity of Fe-smectites changes, particularly where interactions with water and various organic compounds are involved. For instance, the presence of reduced Fe-smectites has been found to induce the degradation of certain organic contaminants found in groundwaters and the subsurface, e.g. chlorinated aliphatics and nitroaromatic compounds. The goal of this study is to develop an in-situ groundwater remediation technology that targets redox- sensitive organics, in the form of a permeable Bio Fe-clay barrier. To achieve this, the iron-reducing bacterium Shewanella algae BrY was first used to reduce structural FeIII in <2micron fractions of the Fe- rich smectite nontronite (NAu-2, 41.74wt% Fe2O3) and a Fe-bearing montmorrillonite (Speeton Clay, Yorkshire, UK, ~8wt% Fe2O3). S. algae BrY was able to reduce structural FeIII within these clays to maximum Fe(II)/Fe(II)+Fe(III) ratios 0.34 and 0.19 for the nontronite and Speeton Clay, respectively, in the presence and absence of the electron shuttle, AQDS (9, 10-anthraquinone-2, 6-disulfonic acid). These results are novel because the capability of S. algae BrY to reduce structural Fe(III) in smectite clays has not previously been tested. Nitrobenzene was selected as the test redox-sensitive organic compound as it is a common subsurface contaminant and is of global ecotoxicological concern. To test the capability of bio- reduced Fe-clays to transform nitrobenzene to aniline (the less toxic and more stable degradation product of nitrobenzene), nontronite suspensions with reduction levels of 20% and 30% were spiked with various concentrations of nitrobenzene and monitored for 5 days. Results showed that when reduced clay, S. algae BrY and AQDS were present, 100% of the nitrobenzene had been transformed to aniline within 24 hours. Further recent results suggest that bio-reduced nontronite alone is also capable of degrading nitrobenzene but at a slower rate than when AQDS is present. Future experiments will constrain absorption and degradation rates of nitrobenzene in contact with the reduced Fe-clays and the role(s) of the Fe-reducing bacteria. Results to date will be presented.

Dynamic properties of composite cemented clay.

PubMed

Cai, Yuan-Qiang; Liang, Xu

2004-03-01

In this work, the dynamic properties of composite cemented clay under a wide range of strains were studied considering the effect of different mixing ratio and the change of confining pressures through dynamic triaxial test. A simple and practical method to estimate the dynamic elastic modulus and damping ratio is proposed in this paper and a related empirical normalized formula is also presented. The results provide useful guidelines for preliminary estimation of cement requirements to improve the dynamic properties of clays.

The pharmaceutical vial capping process: Container closure systems, capping equipment, regulatory framework, and seal quality tests.

PubMed

Mathaes, Roman; Mahler, Hanns-Christian; Buettiker, Jean-Pierre; Roehl, Holger; Lam, Philippe; Brown, Helen; Luemkemann, Joerg; Adler, Michael; Huwyler, Joerg; Streubel, Alexander; Mohl, Silke

2016-02-01

Parenteral drug products are protected by appropriate primary packaging to protect against environmental factors, including potential microbial contamination during shelf life duration. The most commonly used CCS configuration for parenteral drug products is the glass vial, sealed with a rubber stopper and an aluminum crimp cap. In combination with an adequately designed and controlled aseptic fill/finish processes, a well-designed and characterized capping process is indispensable to ensure product quality and integrity and to minimize rejections during the manufacturing process. In this review, the health authority requirements and expectations related to container closure system quality and container closure integrity are summarized. The pharmaceutical vial, the rubber stopper, and the crimp cap are described. Different capping techniques are critically compared: The most common capping equipment with a rotating capping plate produces the lowest amount of particle. The strength and challenges of methods to control the capping process are discussed. The residual seal force method can characterize the capping process independent of the used capping equipment or CCS. We analyze the root causes of several cosmetic defects associated with the vial capping process. Copyright © 2015 Elsevier B.V. All rights reserved.

Hollow Cylinder Tests on Boom Clay: Modelling of Strain Localization in the Anisotropic Excavation Damaged Zone

NASA Astrophysics Data System (ADS)

François, Bertrand; Labiouse, Vincent; Dizier, Arnaud; Marinelli, Ferdinando; Charlier, Robert; Collin, Frédéric

2014-01-01

Boom Clay is extensively studied as a potential candidate to host underground nuclear waste disposal in Belgium. To guarantee the safety of such a disposal, the mechanical behaviour of the clay during gallery excavation must be properly predicted. In that purpose, a hollow cylinder experiment on Boom Clay has been designed to reproduce, in a small-scale test, the Excavation Damaged Zone (EDZ) as experienced during the excavation of a disposal gallery in the underground. In this article, the focus is made on the hydro-mechanical constitutive interpretation of the displacement (experimentally obtained by medium resolution X-ray tomography scanning). The coupled hydro-mechanical response of Boom Clay in this experiment is addressed through finite element computations with a constitutive model including strain hardening/softening, elastic and plastic cross-anisotropy and a regularization method for the modelling of strain localization processes. The obtained results evidence the directional dependency of the mechanical response of the clay. The softening behaviour induces transient strain localization processes, addressed through a hydro-mechanical second grade model. The shape of the obtained damaged zone is clearly affected by the anisotropy of the materials, evidencing an eye-shaped EDZ. The modelling results agree with experiments not only qualitatively (in terms of the shape of the induced damaged zone), but also quantitatively (for the obtained displacement in three particular radial directions).

Effect on mechanical properties of glass reinforced epoxy (GRE) pipe filled with different geopolymer filler molarity for piping application

NASA Astrophysics Data System (ADS)

Hashim, M. F. Abu; Abdullah, M. M. A.; Ghazali, C. M. R.; Hussin, K.; Binhussain, M.

2017-04-01

This study investigated the use of a novel white clay geopolymer as a filler to produce high strength glass reinforced epoxy pipe. It was found that using white clay geopolymer as filler gives better compressive strength to the glass reinforced epoxy pipe. The disadvantages of current glass reinforced epoxy pipes such low compressive strength which can be replaced by the composite pipes. Geopolymerization is an innovative technology that can transform several aluminosilicate materials into useful products called geopolymers or inorganic polymers. A series of glass reinforced epoxy pipe and glass reinforced epoxy pipe filled with 10 - 40 weight percentages white clay geopolymer filler with 4 Molarity and 8 Molarity were prepared. Morphology of white clay geopolymer filler surface was indicates using scanning electron microscopy. The additions of white clay geopolymer filler for both 4 Molarity and 8 Molarity show higher compressive strength than glass reinforced epoxy pipe without any geopolymer filler. The compressive test of these epoxy geopolymer pipe samples was determined using Instron Universal Testing under compression mode. Nonetheless, the compressive strength of glass reinforced epoxy pipe with white clay geopolymer filler continues to drop when added to 40 wt% of the geopolymer filler loading for both 4 Molarity and 8 Molarity. These outcomes showed that the mixing of geopolymer materials in epoxy system can be attained in this research.

The growth-defense trade-off and habitat specialization by plants in Amazonian forests.

PubMed

Fine, Paul V A; Miller, Zachariah J; Mesones, Italo; Irazuzta, Sebastian; Appel, Heidi M; Stevens, M Henry H; Sääksjärvi, Ilari; Schultz, Jack C; Coley, Phyllis D

2006-07-01

Tropical forests include a diversity of habitats, which has led to specialization in plants. Near Iquitos, in the Peruvian Amazon, nutrient-rich clay forests surround nutrient-poor white-sand forests, each harboring a unique composition of habitat specialist trees. We tested the hypothesis that the combination of impoverished soils and herbivory creates strong natural selection for plant defenses in white-sand forest, while rapid growth is favored in clay forests. Recently, we reported evidence from a reciprocal-transplant experiment that manipulated the presence of herbivores and involved 20 species from six genera, including phylogenetically independent pairs of closely related white-sand and clay specialists. When protected from herbivores, clay specialists exhibited faster growth rates than white-sand specialists in both habitats. But, when unprotected, white-sand specialists outperformed clay specialists in white-sand habitat, and clay specialists outperformed white-sand specialists in clay habitat. Here we test further the hypothesis that the growth defense trade-off contributes to habitat specialization by comparing patterns of growth, herbivory, and defensive traits in these same six genera of white-sand and clay specialists. While the probability of herbivore attack did not differ between the two habitats, an artificial defoliation experiment showed that the impact of herbivory on plant mortality was significantly greater in white-sand forests. We quantified the amount of terpenes, phenolics, leaf toughness, and available foliar protein for the plants in the experiment. Different genera invested in different defensive strategies, and we found strong evidence for phylogenetic constraint in defense type. Overall, however, we found significantly higher total defense investment for white-sand specialists, relative to their clay specialist congeners. Furthermore, herbivore resistance consistently exhibited a significant trade-off against growth rate in each of the six phylogenetically independent species-pairs. These results confirm theoretical predictions that a trade-off exists between growth rate and defense investment, causing white-sand and clay specialists to evolve divergent strategies. We propose that the growth-defense trade-off is universal and provides an important mechanism by which herbivores govern plant distribution patterns across resource gradients.

Polyimide Nanocomposites Prepared from High-Temperature, Reduced Charge Organoclays

NASA Technical Reports Server (NTRS)

Delozier, D. M.; Orwoll, R. A.; Cahoon, J. F.; Ladislaw, J. S.; Smith, J. G., Jr.; Connell, J. W.

2003-01-01

Montmorillonite clays modified with the dihydrochloride salt of 1,3-bis(3-aminophenoxy)benzene (APB) were used in the preparation of polyimide/organoclay hybrid films. Organoclays with varying surface charge based upon APB were prepared and examined for their dispersion behavior in the polymer matrix. High molecular weight poly(amide acid) solutions were prepared in the presence of the organoclays. Films were cast and subsequently heated to 300C to cause imidization. The resulting nanocomposite films, containing 3 wt% of organoclay, were characterized by transmission electron microscopy and X-ray diffraction. The clay's cation exchange capacity (CEC) played a key role in determining the extent of dispersion in the polyimide matrix. Considerable dispersion was observed in some of the nanocomposite films. The most effective organoclay was found to have a CEC of 0.70 meq/g. Nanocomposite films prepared with 3-8 wt% of this organoclay were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), and thin-film tensile testing. High levels of clay dispersion could be achieved even at the higher clay loadings. Results from mechanical testing revealed that while the moduli of the nanocomposites increased with increasing clay loadings, both strength and elongation decreased.

Mineralogy and instrumental neutron activation analysis of seven National Bureau of Standards and three Instituto de Pesquisas Tecnologicas clay reference samples

USGS Publications Warehouse

Hosterman, John W.; Flanagan, F.J.; Bragg, Anne; Doughten, M.W.; Filby, R.H.; Grimm, Catherine; Mee, J.S.; Potts, P.J.; Rogers, N.W.

1987-01-01

The concentrations of 3 oxides and 29 elements in 7 National Bureau of Standards (NBS) and 3 Instituto de Pesquisas Techno16gicas (IPT) reference clay samples were etermined by instrumental neutron activation analysis. The analytical work was designed to test the homogeneity of constituents in three new NBS reference clays, NBS-97b, NBS-98b, and NBS-679. The analyses of variance of 276 sets of data for these three standards show that the constituents are distributed homogeneously among bottles of samples for 94 percent of the sets of data. Three of the reference samples (NBS-97, NBS-97a, and NBS-97b) are flint clays; four of the samples (NBS-98, NBS-98a, NBS-98b, and IPT-32) are plastic clays, and three of the samples (NBS-679, IPT-28, and IPT-42) are miscellaneous clays (both sedimentary and residual). Seven clays are predominantly kaolinite; the other three clays contain illite and kaolinite in the approximate ratio 3:2. Seven clays contain quartz as the major nonclay mineral. The mineralogy of the flint and plastic clays from Missouri (NBS-97a and NBS-98a) differs markedly from that of the flint and plastic clays from Pennsylvania (NBS-97, NBS-97b, NBS-98, and NBS-98b). The flint clay NBS-97 has higher average chromium, hafnium, lithium, and zirconium contents than its replacement, reference sample NBS-97b. The differences between the plastic clay NBS-98 and its replacement, NBS-98b, are not as pronounced. The trace element contents of the flint and plastic clays from Missouri, NBS-97a and NBS-98a, differ significantly from those of the clays from Pennsylvania, especially the average rare earth element (REE) contents. The trace element contents of clay sample IPT-32 differ from those of the other plastic clays. IPT-28 and IPT-42 have some average trace element contents that differ not only between these two samples but also from all the other clays. IPT-28 has the highest summation of the average REE contents of the 10 samples. The uranium content of NBS-98a, 46 parts per million, is very much higher than that of the other clays. Plots of average REE contents of the flint and plastic clays, normalized to chondritic abundances, show that the clays from Missouri differ from the same types of clay from Pennsylvania. The plot of REE contents for the miscellaneous clays shows that the normalized means for the elements lanthanum through samarium for IPT-28 are much greater than those for the other miscellaneous clays. The means for the elements europium through lutetium are similar for all three miscellaneous clays.

Enzyme induction in neonates after fetal exposure to antiepileptic drugs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rating, D.; Jaeger-Roman, E.; Nau, H.

1983-01-01

The /sup 13/C-AP breath test is shown to be a convenient, noninvasive method to monitor velocity and capacity of P450-dependent AP N-demethylation in infancy and childhood. According to /sup 13/C-AP breath tests, neonates have a very low capacity to eliminate /sup 13/CO/sub 2/, which is only 15 to 21% of the activity in adults. During the first year of life AP N-demethylation increases to reach its maximum at about 2 years; afterwards a slight decrease occurs. In 25 neonates exposed prenatally to different antiepileptic drugs /sup 13/C-AP breath test was efficiently used to prove that cytochrome AP N-demethylation was considerablymore » stimulated. After primidone/phenobarbitone, especially in combination with phenytoin, /sup 13/C elimination reaches and even surpasses the range for older children. Valproate exposure during fetal life is not consistently followed by a significant increase in AP N-demethylation. The enzyme induction demonstrated by /sup 13/C-AP breath test was often accompanied by accelerated metabolic clearance and shortened half-life times of transplacentally acquired antiepileptic drugs. There was good agreement between /sup 13/C-AP breath tests and pharmacokinetic data for primidone/phenobarbitone but not for phenytoin. In contrast, in the case of phenytoin exposure during pregnancy the pharmacokinetic parameters and the /sup 13/C breath test data will transport very different informations about enzyme induction in these neonates.« less

EVALUATION USING AN ORGANOPHILIC CLAY TO CHEMICALLY STABILIZE WASTE CONTAINING ORGANIC COMPOUNDS

EPA Science Inventory

A modified clay (organophilic) was utilized to evaluate the potential for chemically stabilizing a waste containing organic compounds. hemical bonding between the binder and the contaminants was indicated. eachate testing also indicated strong binding. Copy available at NTIS as ...

New trends in the prevention and management of community-acquired pneumonia.

PubMed

Postma, D F; van Werkhoven, C H; Huijts, S M; Bolkenbaas, M; Oosterheert, J J; Bonten, M J M

2012-10-01

Community-acquired pneumonia (CAP) is an important cause of morbidity and mortality worldwide. This review summarises current trends and knowledge gaps in CAP management and prevention. Although Streptococcus pneumoniae is the most frequent cause of CAP, identification of the microbial cause of infection remains unsuccessful in most episodes, and little is known about the aetiology of CAP in immunocompromised patients. Urinary antigen testing has become standard care for diagnosing Legionella infection, and pneumococcal urinary antigen testing is now recommended in the Dutch guidelines to streamline antibiotic therapy in patients hospitalised with CAP. In primary care C-reactive protein determination is recommended to improve antibiotic prescription for lower respiratory tract infections. In patients hospitalised with CAP, three strategies are considered equally effective for choosing empirical antibiotic treatment. Yet, more (and better designed) studies are needed to determine the best strategy, as well as to determine optimal (which usually means the minimum) duration of antibiotic therapy and the role of adjuvant treatment with corticosteroids. The effectiveness of the 23-valent pneumococcal polysaccharide vaccine in preventing invasive pneumococcal disease and pneumococcal CAP remains debated, and whether the newer conjugate vaccines are more effective remains to be determined. Many of these questions are currently being addressed in large-scaled trials in the Netherlands, and their results may allow evidence-based decisions in CAP management and prevention.

Reformulation of the CBR Procedure, Report 2: Design, Construction, and Behavior Under Traffic of the Pavement Test Sections

DTIC Science & Technology

2013-12-01

shows the clay moisture- density curve. The design subgrade CBR values selected for the test section construction were 4%, 10%, and 15%. The high...9  Figure 7. Subgrade moisture- density curve...view of Hangar 4. (a) (b) The in situ soil was a lean clay (loess) deposit, and the depth to the groundwater table was approximately 6 ft

A Closer Look at Holden Crater

NASA Image and Video Library

2017-03-15

Holden Crater in southern Margaritifer Terra displays a series of finely layered deposits on its floor. The layered deposits are especially well exposed in the southwestern section of the crater where erosion by water flowing through a breach in the crater rim created spectacular outcrops. In this location, the deposits appear beneath a cap of alluvial fan materials (tan to brown in this image). Within the deposits, individual layers are nearly flat-lying and can be traced for hundreds of meters to kilometers. Information from the CRISM instrument on the Mars Reconnaissance Orbiter suggests that at least some of these beds contain clays. By contrast, the beds in the overlying alluvial fan are less continuous and dip in varying directions, showing less evidence for clays. Collectively, the characteristics of the finely bedded deposits suggest they may have been deposited into a lake on the crater floor, perhaps fed by runoff related to formation of the overlying fans. The map is projected here at a scale of 25 centimeters (9.8 inches) per pixel. [The original image scale is 25.9 centimeters (10.2 inches) per pixel (with 1 x 1 binning); objects on the order of 78 centimeters (30.7 inches) across are resolved.] North is up. http://photojournal.jpl.nasa.gov/catalog/PIA21561

Comparison of the skin-prick test and Phadia ImmunoCAP as tools to diagnose house-dust mite allergy.

PubMed

Jung, Yong Gi; Cho, Hyun-Jin; Park, Ga Young; Min, Jin-Young; Kim, Hyo Yeol; Dhong, Hun-Jong; Chung, Seung Kyu; Kim, Seon Woo

2010-01-01

When the skin-prick test (SPT) and in vitro test such as ImmunoCAP assay are performed simultaneously, results do not always coincide in some patients. Our objectives, therefore, were (1) to assess differences in allergic test results according to age group and (2) to establish appropriate guidelines for diagnosing mite allergy according to age. A total of 692 participants complaining of allergic rhinitis symptoms participated. Patients were divided according to age; the mean age was 32 years (range, 8-76 years). The SPT and ImmunoCAP assays were performed to detect allergies to house-dust mites (Dermatophagoides pteronyssinus and Dermatophagoides farinae). The association between age and the result of each allergy test were examined, and a cutoff age for proper application of each test was than estimated. Three hundred thirty-six patients (48.6%) were allergic to D. pteronyssinus and 350 patients (50.6%) were allergic to D. farinae. In the case of D. pteronyssinus, SPT was proved to be more useful in detecting allergy for subjects <50 years old (p < 0.0001). However in case of D. farinae, ImmunoCAP was useful for all age groups, but SPT showed decreased ratio of positive result for subjects >30 years old (p < 0.0001). This study was the first to compare results of allergy tests according to age using true allergens. For patients >50 years of age, the ImmunoCAP was found to be the preferred method for detecting allergy to house-dust mites and for patients <30 years old, SPT is the recommended first choice.

Influence of Clay Content, Mineralogy and Fabric On Radar Frequency Response of Aquifer Materials

NASA Astrophysics Data System (ADS)

West, L. J.; Handley, K.

High frequency electromagnetic methods such as ground penetrating radar (GPR) and time domain reflectometry (TDR) are widely employed to measure water saturation in the vadose zone and water filled porosity in the saturated zone. However, previous work has shown that radar frequency dielectric properties are strongly influenced by clay as well as by water content. They have also shown that that the dielectric response of clay minerals is strongly frequency dependent, and that even a small proportion of clay such as that present in many sandstone aquifers can have a large effect at typi- cal GPR frequencies (around 100MHz). Hence accurate water content/porosity deter- mination requires clay type and content to be taken into account. Reported here are dielectric measurements on clay-sand mixtures, aimed at investigating the influence of clay mineralogy, particle shape, and the geometrical arrangement of the mixture constituents on GPR and TDR response. Dielectric permittivity (at 50-1000MHz) was measured for mixtures of Ottawa Sand and various clay minerals or clay size quartz rock flour, using a specially constructed dielectric cell. Both homogeneous and layered mixtures were tested. The influence of pore water salinity, clay type, and particle arrangement on the dielectric response is interpreted in terms of dielectric dispersion mechanisms. The appropriateness of var- ious dielectric mixing rules such as the Complex Refractive Index Method (CRIM) for determination of water content or porosity from field GPR and TDR data are dis- cussed.

Investigating the Influence of Clay Mineralogy on Stream Bank Erodibility

NASA Astrophysics Data System (ADS)

Ambers, R. K.; Stine, M. B.

2005-12-01

Soil scientists concerned with erosion of agricultural fields and geotechnical engineers concerned with the mechanical behavior of soils under different conditions have both examined the role of clay mineralogy in controlling soil/sediment properties. Fluvial geomorphologists studying stream channel erosion and stability have focused more on the effects of particle-size distribution, vegetation and rooting. The clay mineralogy of bed and bank sediment has the potential to influence cohesiveness and erodibility, however. The goal of this study is to determine the influence of clay mineralogy on the erodibility of natural stream bank sediment, utilizing techniques drawn from pedology and soil mechanics. Bank samples were collected from eleven sites in small watersheds in central and western Virginia. To obtain sediment containing a range of different clay minerals, watersheds with different types of bedrock were chosen for sampling. Rock types included mafic to felsic metamorphic and igneous rocks, shale, sandstone, and limestone. Where stream bank materials were clearly stratified, different layers were sampled separately. X-ray diffraction of the clay-fraction of the sediment indicates the presence of kaolinite, illite, vermiculite, and mixed-layer clay minerals in various abundances in the different samples. Clay content is 9-46%, as determined by the hydrometer method, and textures range from silty clay and silt loam to clay loam and sandy loam. Organic mater contents range from 1-5% by the loss-on-ignition method. Bulk density of intact sediment samples averages 1.5 g/cc. Liquid limits range from 23-41 with one sample having a value of 65; plasticity indices range from 15-22. While these tests predict that the samples would show a range of mechanical behaviors, the channel morphology at the sampling sites was not strikingly different, all having steep cut banks eroded primarily by scour with no evidence of mass movement and most having a width/depth ratio around 4.5. The ASTM pinhole test for identifying dispersive clay soils is being adapted to measure erodibility of intact and remolded sediment samples in the laboratory to look for more subtle differences in behavior under erosive conditions. Factors such as the extent and method of sample compaction are being taken into account in order to standardize the method.

Adsorption and Desorption of Cesium in Clay Minerals: Effects of Natural Organic Matter and pH

NASA Astrophysics Data System (ADS)

Yoon, Hongkyu; Ilgen, Anastasia; Mills, Melissa; Lee, Moo; Seol, Jeung Gun; Cho, Nam Chan; Kang, Hyungyu

2017-04-01

Cesium (Cs) released into the environment (e.g., Fukushima accident) poses significant environmental concerns and remediation challenges. A majority of Cs in the environment have remained within the surface soils due to the strong adsorption affinity of Cs towards clay minerals. Different clay minerals have different bonding sites, resulting in various adsorption mechanisms at nanometer scale. For example, the illite commonly has a basal spacing of 1.0 nm, but becomes wider to 1.4 nm once other cations exchange with K in the interlayer site. Cs adsorbs into these expanded wedged zone strongly, which can control its mobility in the environment. In addition, natural organic matter (NOM) in the surface soils can interact with clay minerals, which can modify the mechanisms of Cs adsorption on the clay minerals by blocking specific adsorption sites and/or providing Cs adsorption sites on NOM surface. In this work, three representative clay minerals (illite, vermiculite, montmorillonite) and humic acid (HA) are used to systematically investigate the adsorption and desorption behavior of Cs. We performed batch adsorption experiments over a range of Cs concentrations on three clay minerals with and without HA, followed by sequential desorption batch testing. We tested desorption efficiency as a function of initial adsorbed Cs concentration, HA content, sodium concentration, and pH. The sequential extraction results are compared to the structural changes in clay minerals, measured using extended X-ray absorption fine structure spectroscopy (EXAFS) and aberration-corrected (scanning) transmission electron microscopy (TEM) - energy dispersive X-ray spectroscopy (EDX). Hence, this work aims to identify the mechanisms of Cs fixation at the nanometer (or atomic-) scale as a function of the clay mineral properties (e.g. expandability, permanent surface charge) and varying organic matter content at different pH values and to enhance our atomic-scale mechanistic understanding of the clay mineral interactions with cesium in the presence of NOM. The expandability of clay minerals and effect of HA addition on Cs adsorption and desorption are highlighted to address the efficiency of Cs removal schemes from contaminated soils. Sandia National Laboratories is a multi-mission laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

In situ synthesis, characterization, and catalytic performance of tungstophosphoric acid encapsulated into the framework of mesoporous silica pillared clay.

PubMed

Li, Baoshan; Liu, Zhenxing; Han, Chunying; Ma, Wei; Zhao, Songjie

2012-07-01

Mesoporous silica pillared clay (SPC) incorporated with tungstophosphoric acid (HPW) has been synthesized via in situ introducing P and W source in the acidic suspension of the clay interlayer template during the formation of the silica pillared clay. The samples were characterized by XRD, XRF, FT-IR, TG-DTA, N(2) adsorption-desorption, and SEM techniques. The results showed that the HPW formed by in situ method has been effectively introduced into the framework of mesoporous silica pillared clay and its Keggin structure remained perfectly after formation of the materials. In addition, samples with similar HPW loadings were also prepared by impregnation method using SPC as the support. HPW in the incorporated samples was better dispersed into the silica pillared clay than in the impregnated samples. The results of catalytic tests indicated that the encapsulated materials demonstrated better catalytic performance than the impregnated samples in oxidative desulfurization (ODS) of dibenzothiophene (DBT). Copyright © 2012 Elsevier Inc. All rights reserved.

The influence of clay fineness upon sludge recycling in a ceramic matrix

NASA Astrophysics Data System (ADS)

Szőke, A. M.; Muntean, M.; Sándor, M.; Brotea, L.

2016-04-01

The feasibility of sludge recycling in the ceramic manufacture was evaluated through laboratory testing. Such residues have similar chemical and mineralogical composition with the raw mixture of the green ceramic body used in construction. Several ceramic masses with clay and various proportion of sludge have been synthesized and then characterized by their physical-mechanical properties. The fineness of the clay, the main component of the green ceramic body, has been considered for every raw mixture. The proportion of the sludge waste addition depends on the clay fineness and the sintering capacity also, increases with the clay fineness. The ceramic properties, particularly, the open porosity, and mechanical properties, in presence of small sludge proportion (7, 20%) shows small modification. The introduction of such waste into building ceramic matrix (bricks, tiles, and plates) has a very good perspective.

Pangaea, She No Spin

NASA Astrophysics Data System (ADS)

McDowell, M.

2002-12-01

Looking at lopsided Pangaea, shown imaginatively on many illustrated proposals, I wondered what would happen if the configuration were put in high relief on a globe and spun on axis. Then I wondered if the present configuration of land masses would itself balance as a spinning top. So I got two Replogle globes, two boxes of colored modeling clay sticks, and two fat knitting needles, to fit through the capped holes at the poles of the globes. The clay sticks I cut up into 3 mm. (1/8") slices, using a different color for each continent, and applied to the first globe, assuming the extreme exaggeration above the geoid, no matter how crude, would tell the story. Inserting one needle through the globe and securing it, I balanced the globe on the point of the needle and twirled it like a top. Result: Wobbly! Top end of needle gyrated unevenly, and here it was supposed to make a smooth precessional cone. Oh boy. For the second globe, I used a Scotese "free stuff" interpretation of Pangaea, which I had to augment considerably using USGS, DuToit, Irving and other references, fitting it on the globe and applying identical clay color slices to what I judged generally accepted land surfaces. Result: the thing would hardly stand up, let alone spin. Conclusion: Although a refinement of application on the "today" globe might eliminate nutation, creating a smoother spin, there is no way any refinement of Pangaea on the same size globe can come close. While the concept of a supercontinent may be viable, I theorize that it had to have evolved on a far smaller globe, where land mass could balance, and the "breakup" would not have caused us to wildly gyrate on our axis. Because Pangaea, she no spin.

Diagnostic, therapeutic and economic consequences of a positive urinary antigen test for Legionella spp. in patients admitted with community-acquired pneumonia: a 7-year retrospective evaluation.

PubMed

Engel, M F; van Manen, L; Hoepelman, A I M; Thijsen, S; Oosterheert, J J

2013-09-01

A positive urinary antigen test for Legionella spp. (Legionella urinary antigen test; LUAT) allows an early switch from empiric to targeted treatment (TT) in hospitalised, community-acquired pneumonia (CAP) patients. We aimed to evaluate the diagnostic, therapeutic and economic consequences of this frequently used test 7 years after its implementation. We retrospectively evaluated LUATs performed between 2005 and 2011 in two teaching hospitals. All tests performed in hospitalised CAP patients were used in the economic evaluation and positive tests were included in the treatment evaluation. Data on patient characteristics, admission and outcome were retrieved from the patients' files. The number of days gained by making a rapid aetiological diagnosis, the number of days TT could be provided and their costs were calculated. Of 4485 LUATs, 2504 (56%) were performed for CAP including 55 (1%) positive tests (€1041/positive test). In 26 (60%) of the 43 included positive tests, LUAT was the only test showing Legionella spp. Subsequently, earlier TT was possible in the remaining cases during 209 cumulative admission days (€274/TT day). LUAT led to detection of Legionella spp. 13 days earlier per case (€203/day) as compared with culture/serology alone. Timely LUAT use in accordance with current guidelines allows early detection and treatment of CAP caused by Legionella spp. at considerable expense.

DSTO Landmine Detection Test Targets

DTIC Science & Technology

2005-06-01

cm diameter, 10 cm high. x x GS 32D50 Galvanised steel, pipe, hollow, 32 cm diameter, 50 cm long, ends capped x x GS 45D50 Galvanised Steel, pipe...hollow, 45 cm diameter, 50 cm long, ends capped x x GS 75D50 Galvanised Steel, pipe, hollow, 75 cm diameter, 50 cm long, ends capped x x

The antioxidative and hepatoprotective effects comparison of Chinese angelica polysaccharide(CAP)and selenizing CAP (sCAP) in CCl4 induced hepatic injury mice.

PubMed

Gao, Zhenzhen; Zhang, Chao; Tian, Weijun; Liu, Kuanhui; Hou, Ranran; Yue, Chanjuan; Wu, Yi; Wang, Deyun; Liu, Jiaguo; Hu, Yuanliang; Yang, Ying

2017-04-01

Chinese angelica polysaccharides (CAP) and selenizing CAP (sCAP) were prepared and identified through FTIR and SEM observation. Their antioxidant activities in vitro and hepatoprotective effects in vivo were compared by free radical-scavenging tests or with CCl 4 -induced hepatic injury model mice. The results showed that for DPPH radical, superoxide anion and hydroxyl radical, the scavenging capabilities of sCAP were significantly stronger than those of CAP . In hepatic injury model mice, sCAP could significantly reduce ALT, AST and ALP contents and raised TP content in serum, significantly reduce MDA and ROS contents and raised SOD and T-AOC activities in liver homogenate in comparison with CAP; obviously relieve the pathological changes of liver and significantly inhibit the expressions of p-ERK, p-JNK and p-p38 protein as compared with those in model control group. These results indicate that selenylation modification can enhance the antioxidant and hepatoprotective actions of Chinese angelica polysaccharide. A action mechanism of sCAP is suppressing the protein expression of MAPK signaling pathway. Copyright © 2017 Elsevier B.V. All rights reserved.

Behavior of nonplastic silty soils under cyclic loading.

PubMed

Ural, Nazile; Gunduz, Zeki

2014-01-01

The engineering behavior of nonplastic silts is more difficult to characterize than is the behavior of clay or sand. Especially, behavior of silty soils is important in view of the seismicity of several regions of alluvial deposits in the world, such as the United States, China, and Turkey. In several hazards substantial ground deformation, reduced bearing capacity, and liquefaction of silty soils have been attributed to excess pore pressure generation during dynamic loading. In this paper, an experimental study of the pore water pressure generation of silty soils was conducted by cyclic triaxial tests on samples of reconstituted soils by the slurry deposition method. In all tests silty samples which have different clay percentages were studied under different cyclic stress ratios. The results have showed that in soils having clay content equal to and less than 10%, the excess pore pressure ratio buildup was quicker with an increase in different cyclic stress ratios. When fine and clay content increases, excess pore water pressure decreases constant cyclic stress ratio in nonplastic silty soils. In addition, the applicability of the used criteria for the assessment of liquefaction susceptibility of fine grained soils is examined using laboratory test results.

Behavior of Nonplastic Silty Soils under Cyclic Loading

PubMed Central

Ural, Nazile; Gunduz, Zeki

2014-01-01

The engineering behavior of nonplastic silts is more difficult to characterize than is the behavior of clay or sand. Especially, behavior of silty soils is important in view of the seismicity of several regions of alluvial deposits in the world, such as the United States, China, and Turkey. In several hazards substantial ground deformation, reduced bearing capacity, and liquefaction of silty soils have been attributed to excess pore pressure generation during dynamic loading. In this paper, an experimental study of the pore water pressure generation of silty soils was conducted by cyclic triaxial tests on samples of reconstituted soils by the slurry deposition method. In all tests silty samples which have different clay percentages were studied under different cyclic stress ratios. The results have showed that in soils having clay content equal to and less than 10%, the excess pore pressure ratio buildup was quicker with an increase in different cyclic stress ratios. When fine and clay content increases, excess pore water pressure decreases constant cyclic stress ratio in nonplastic silty soils. In addition, the applicability of the used criteria for the assessment of liquefaction susceptibility of fine grained soils is examined using laboratory test results. PMID:24672343

Determination of Aflatoxin M1 and Chloramphenicol in Milk Based on Background Fluorescence Quenching Immunochromatographic Assay.

PubMed

Wu, Xiaoxia; Tian, Xiaofeng; Xu, Lihua; Li, Jiutong; Li, Xinxia; Wang, Yuwen

2017-01-01

Harsh demanding has been exposed on the concentration of aflatoxin M1 (AFM1) and chloramphenicol (CAP) in milk. In this study, we developed a new method based on background fluorescence quenching immunochromatographic assay (bFQICA) to detect AFM1 and CAP in milk. The detection limit for AFM1 was 0.0009 ng/mL, while that for the CAP was 0.0008 ng/mL. The assay variability was determined with 3 AFM1 standards (i.e., 0.25 ng/mL, 0.5 ng/mL, and 1.0 ng/mL), and the actual detection value was 0.2497, 0.5329, and 1.0941, respectively. For the assay variability of 3 CAP standards (i.e., 0.10 ng/mL, 0.30 ng/mL, and 0.50 ng/mL), the actual detection value was 0.0996, 0.3096, and 0.4905, respectively. The recovery rate of AFM1 was 99.7%-101.7%, while that for CAP was 95.3%-97.6%. For the test stability, AFM1 and CAP showed satisfactory test stability even at month 5. Compared with the sensitivity of liquid chromatography-mass spectrometry (LC-MS) method, no statistical difference was noticed in results of the bFQICA. Our method is convenient for the detection of AFM1 and CAP in milk with a test duration of about 8 minutes. Additionally, an internal WiFi facility is provided in the system allowing for quick connection and storage in the intelligent cell phone.

Community-acquired pneumonia requiring hospitalization: rational decision making and interpretation of guidelines.

PubMed

Postma, Douwe F; van Werkhoven, Cornelis H; Oosterheert, Jan Jelrik

2017-05-01

This review focuses on the evidence base for guideline recommendations on the diagnosis, the optimal choice, timing and duration of empirical antibiotic therapy, and the use of microbiological tests for patients hospitalized with community-acquired pneumonia (CAP): issues for which guidelines are frequently used as a quick reference. Furthermore, we will discuss possibilities for future research in these topics. Many national and international guideline recommendations, even on critical elements of CAP management, are based on low-to-moderate quality evidence. The diagnosis and management of CAP has hardly changed for decades. The recommendation to cover atypical pathogens in all hospitalized CAP patients is based on observational studies only and is challenged by two recent trials. The following years, improved diagnostic testing, radiologically by low-dose Computed Tomography or ultrasound and/or microbiologically by point-of-care multiplex PCR, has the potential to largely influence the choice and start of antibiotic therapy in hospitalized CAP patients. Rapid microbiological testing will hopefully improve antibiotic de-escalation or early pathogen-directed therapy, both potent ways of reducing broad-spectrum antibiotic use. Current guideline recommendations on the timing and duration of antibiotic therapy are based on limited evidence, but will be hard to improve.

Comparison of the Roche COBAS Amplicor Monitor, Roche COBAS Ampliprep/COBAS Taqman and Abbott RealTime Test assays for quantification of hepatitis C virus and HIV RNA.

PubMed

Wolff, Dietmar; Gerritzen, Andreas

2007-01-01

We have evaluated the performance of two newly developed automated real-time PCR assays, the COBAS Ampliprep/COBAS TaqMan (CAP/CTM) and the Abbott RealTime tests, in the quantification of human immunodeficiency virus (HIV) and hepatitis C virus (HCV) RNA. The widely used semi-automated COBAS Amplicor Monitor (CAM) assay served as the reference test. Several specimens were analyzed, including 102 plasma samples from HCV patients and 109 from HIV patients and 10 samples from negative donors, as well as Quality Control in Molecular Diagnostics (QCMD) and National Institute for Biological Standards and Controls (NIBSC) proficiency program panels. Good correlation was observed among the three assays, with correlation coefficients (R2) of 0.8 (CAM-CAP/CTM), 0.89 (CAM-RealTime) and 0.91 (CAP/CTM-RealTime) for HCV and 0.83 (CAM-RealTime), 0.85 (CAM-CAP/CTM) and 0.89 (CAP/CTM-RealTime) for HIV. The overall concordance for negative/positive results was 100% for HCV and 98% for HIV. All assays were equally able to quantify HCV genotypes 1, 3, 5 and HIV group M (subtypes A-H) and N from QCMD and NIBSC panels. In terms of workflow, the RealTime assay requires more hands-on-time than the CAP/CTM assay. The results indicate that real-time PCR assays can improve the efficiency of end-point PCR tests by better covering viral dynamic ranges and providing higher throughput and automation.

Geogrid Reinforced Base Course for Flexible Pavements for Light Aircraft: Literature Review and Test Section Design

DTIC Science & Technology

1991-05-01

GeoarId Reinforced Agregate Layers over Weak Clay Subgrades. Milligan and Love(Z3) conducted small-scale laboratory model tests under plane strain...34. Based on the very limited literature available on geogrid applications in airfield pavements, the literature review was expanded to cover railroad...thicknesses and clay subgrade strengths. Performance of the reinforced systems was significantly better. The increased performance resulted from the

HYDRAULIC CONDUCTIVITY OF THREE GEOSYNTHETIC CLAY LINERS

EPA Science Inventory

The hydraulic conductivity of three 2.9 m² (32 sq ft) geosynthetic clay liners (GCLs) was measured. Tests were performed on individual sheets of the GCLs, on overlapped pieces of GCLs, and on composite liners consisting of a punctured geomembrane overlying a GCL. Hyd...

Clay Caterpillars: A Tool for Ecology & Evolution Laboratories

ERIC Educational Resources Information Center

Barber, Nicholas A.

2012-01-01

I present a framework for ecology and evolution laboratory exercises using artificial caterpillars made from modeling clay. Students generate and test hypotheses about predation rates on caterpillars that differ in appearance or "behavior" to understand how natural selection by predators shapes distribution and physical characteristics of…

Pedologic and climatic controls on Rn-222 concentrations in soil gas, Denver, Colorado

USGS Publications Warehouse

Asher-Bolinder, S.; Owen, D.E.; Schumann, R.R.

1990-01-01

Soil-gas radon concentrations are controlled seasonally by factors of climate and pedology. In a swelling soil of the semiarid Western United States, soil-gas radon concentrations at 100 cm depth increase in winter and spring due to increased emanation with higher soil moisture and the capping effect of surface water or ice. Radon concentrations in soil drop markedly through the summer and fall. The increased insolation of spring and summer warms and dries the soil, limiting the amount of water that reaches 100 cm. Probable controls on the distribution of uranium within the soil column include its downward leaching, its precipitation or adsorption onto B-horizon clays, concretions, or cement, and the uranium content and mineralogy of the soil's granitic and gneissic precursors. -from Authors

Clay-sewage sludge co-pyrolysis. A TG-MS and Py-GC study on potential advantages afforded by the presence of clay in the pyrolysis of wastewater sewage sludge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ischia, Marco, E-mail: marco.ischia@ing.unitn.it; Maschio, Roberto Dal; Grigiante, Maurizio

2011-01-15

Wastewater sewage sludge was co-pyrolyzed with a well characterized clay sample, in order to evaluate possible advantages in the thermal disposal process of solid waste. Characterization of the co-pyrolysis process was carried out both by thermogravimetric-mass spectrometric (TG-MS) analysis, and by reactor tests, using a lab-scale batch reactor equipped with a gas chromatograph for analysis of the evolved gas phase (Py-GC). Due to the presence of clay, two main effects were observed in the instrumental characterization of the process. Firstly, the clay surface catalyzed the pyrolysis reaction of the sludge, and secondly, the release of water from the clay, atmore » temperatures of approx. 450-500 deg. C, enhanced gasification of part of carbon residue of the organic component of sludge following pyrolysis. Moreover, the solid residue remaining after pyrolysis process, composed of the inorganic component of sludge blended with clay, is characterized by good features for possible disposal by vitrification, yielding a vitreous matrix that immobilizes the hazardous heavy metals present in the sludge.« less

Characterization of electron-beam-modified surface coated clay fillers and their influence on physical properties of rubbers

NASA Astrophysics Data System (ADS)

Ray, Sudip; Bhowmick, Anil K.; Sarma, K. S. S.; Majali, A. B.; Tikku, V. K.

2002-12-01

A novel process of surface modification of clay filler has been developed by coating this with an acrylate monomer, trimethylol propane triacrylate (TMPTA) or a silane coupling agent, triethoxy vinyl silane (TEVS) followed by electron beam irradiation. Characterization of these surface modified fillers has been carried out by Fourier-transform infrared analysis (FTIR), electron spectroscopy for chemical analysis (ESCA), wettability by dynamic wicking method measuring the rise of a liquid through a filler-packed capillary tube and water flotation test, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), thermogravimetric analysis (TGA), and X-ray diffraction (XRD). Presence of the acrylate and the silane coupling agent on the modified fillers has been confirmed from FTIR, ESCA, and EDX studies, which has also been supported by TGA studies. The contact angle measurement by dynamic wicking method suggests improvement in hydrophobicity of the treated fillers, which is supported by water flotation test especially in the case of silanized clay. However, XRD studies demonstrate that the entire modification process does not affect the bulk properties of the fillers. Finally, both unmodified and modified clay fillers have been incorporated in styrene butadiene rubber (SBR) and nitrile rubber (NBR). Rheometric and mechanical properties reveal that there is a definite improvement using these modified fillers specially in the case of silanized clay compared to the control sample, probably due to successful enhancement in interaction between the treated clay and the base polymer.

Geohydrology of the High Energy Laser System Test Facility site, White Sands Missile Range, Tularosa Basin, south-central New Mexico

USGS Publications Warehouse

Basabilvazo, G.T.; Nickerson, E.L.; Myers, R.G.

1994-01-01

The Yesum-HoHoman and Gypsum land (hummocky) soils at the High Energy Laser System Test Facility (HELSTF) represent wind deposits from recently desiccated lacustrine deposits and deposits from the ancestral Lake Otero. The upper 15-20 feet of the subsurface consists of varved gypsiferous clay and silt. Below these surfidai deposits the lithology consists of interbedded clay units, silty-clay units, and fine- to medium-grained quartz arenite units in continuous and discontinuous horizons. Clay horizons can cause perched water above the water table. Analyses of selected clay samples indicate that clay units are composed chiefly of kaolinire and mixed-layer illite/ smectite. The main aquifer is representative of a leaky-confined aquifer. Estimated aquifer properties are: transmissivity (T) = 780 feet squared per day, storage coefficient (S) = 3.1 x 10-3, and hydraulic conductivity (K) = 6.0 feet per day. Ground water flows south and southwest; the estimated hydraulic gradient is 5.3 feet per mile. Analyses of water samples indicate that ground water at the HELSTF site is brackish to slightly saline at the top of the main aquifer. Dissolved-solids concentration near the top of the main aquifer ranges from 5,940 to 11,800 milligrams per liter. Predominant ions are sodium and sulfate. At 815 feet below land surface, the largest dissolved-solids concentration measured is 111,000 milligrams per liter, which indicates increasing salinity with depth. Predominant ions are sodium and chloride.

Incorporation of gypsum waste in ceramic block production: Proposal for a minimal battery of tests to evaluate technical and environmental viability of this recycling process.

PubMed

Godinho-Castro, Alcione P; Testolin, Renan C; Janke, Leandro; Corrêa, Albertina X R; Radetski, Claudemir M

2012-01-01

Civil engineering-related construction and demolition debris is an important source of waste disposed of in municipal solid waste landfills. After clay materials, gypsum waste is the second largest contributor to the residential construction waste stream. As demand for sustainable building practices grows, interest in recovering gypsum waste from construction and demolition debris is increasing, but there is a lack of standardized tests to evaluate the technical and environmental viability of this solid waste recycling process. By recycling gypsum waste, natural deposits of gypsum might be conserved and high amounts of the waste by-product could be reused in the civil construction industry. In this context, this paper investigates a physical property (i.e., resistance to axial compression), the chemical composition and the ecotoxicological potential of ceramic blocks constructed with different proportions of clay, cement and gypsum waste, and assesses the feasibility of using a minimal battery of tests to evaluate the viability of this recycling process. Consideration of the results for the resistance to axial compression tests together with production costs revealed that the best formulation was 35% of plastic clay, 35% of non-plastic clay, 10% of Portland cement and 20% of gypsum waste, which showed a mean resistance of 4.64MPa. Energy dispersive X-ray spectrometry showed calcium and sulfur to be the main elements, while quartz, gypsum, ettringite and nacrite were the main crystalline compounds found in this formulation. Ecotoxicity tests showed that leachate from this formulation is weakly toxic toward daphnids and bacteria (EC(20%)=69.0 and 75.0, respectively), while for algae and fish the leachate samples were not toxic at the EC(50%) level. Overall, these results show that the addition of 20% of gypsum waste to the ceramic blocks could provide a viable substitute for clay in the ceramics industry and the tests applied in this study proved to be a useful tool for the technical and environmental evaluation of this recycling process, bacterial and daphnid tests being more sensitive than algae and fish tests. Copyright © 2011 Elsevier Ltd. All rights reserved.

The origin of high sulfate concentrations in a coastal plain aquifer, Long Island, New York

USGS Publications Warehouse

Brown, C.J.; Schoonen, M.A.A.

2004-01-01

Ion-exchange batch experiments were run on Cretaceous (Magothy aquifer) clay cores from a nearshore borehole and an inland borehole on Long Island, NY, to determine the origin of high SO42- concentrations in ground water. Desorption batch tests indicate that the amounts of SO 42- released from the core samples are much greater (980-4700 ??g/g of sediment) than the concentrations in ground-water samples. The locally high SO42- concentrations in pore water extracted from cores are consistent with the overall increase in SO 42- concentrations in ground water along Magothy flow paths. Results of the sorption batch tests indicate that SO42- sorption onto clay is small but significant (40-120 ??g/g of sediment) in the low-pH (<5) pore water of clays, and a significant part of the SO42- in Magothy pore water may result from the oxidation of FeS2 by dissolved Fe(III). The acidic conditions that result from FeS2 oxidation in acidic pore water should result in greater sorption of SO42- and other anions onto protonated surfaces than in neutral-pH pore water. Comparison of the amounts of Cl- released from a clay core sample in desorption batch tests (4 ??g/g of sediment) with the amounts of Cl- sorbed to the same clay in sorption tests (3.7-5 ??g/g) indicates that the high concentrations of Cl- in pore water did not originate from connate seawater but were desorbed from sediment that was previously in contact with seawater. Furthermore, a hypothetical seawater transgression in the past is consistent with the observed pattern of sorbed cation complexes in the Magothy cores and could be a significant source of high SO42- concentrations in Magothy ground water.

A case study on stratified settlement and rebound characteristics due to dewatering in Shanghai subway station.

PubMed

Wang, Jianxiu; Huang, Tianrong; Sui, Dongchang

2013-01-01

Based on the Yishan Metro Station Project of Shanghai Metro Line number 9, a centrifugal model test was conducted to investigate the behavior of stratified settlement and rebound (SSR) of Shanghai soft clay caused by dewatering in deep subway station pit. The soil model was composed of three layers, and the dewatering process was simulated by self-invention of decompressing devise. The results indicate that SSR occurs when the decompression was carried out, and only negative rebound was found in sandy clay, but both positive and negative rebound occurred in the silty clay, and the absolute value of rebound in sandy clay was larger than in silty clay, and the mechanism of SSR was discussed with mechanical sandwich model, and it was found that the load and cohesive force of different soils was the main source of different responses when decompressed.

Improving the Mechanical Performance and Thermal Stability of a PVA-Clay Nanocomposite by Electron Beam Irradiation

NASA Astrophysics Data System (ADS)

Shokuhi Rad, A.; Ebrahimi, D.

2017-07-01

The effects of electron beam irradiation and presence of clay on the mechanical properties and thermal stability of montmorillonite clay-modified polyvinyl alcohol nanocomposites were studied. By using the X-ray diffraction (XRD) and transmission electron microscopy (TEM), the microstructure of the nanocomposites was investigated. The results obtained from TEM and XRD tests showed that montmorillonite clay nanoparticles were located in the polyvinyl alcohol phase. The XRD analysis confirmed the formation of an exfoliated structure in nanocomposites samples. Increasing the amount of clay to 20 wt.% increased the tensile strength and modulus of the nanocomposite. Irradiation up to an absorbed dose of 100 kGy increased its mechanical properties and thermal stability, but at higher irradiation levels, the mechanical strength and thermal stability declined. The sample with 20 wt.% of the nanofiller, exposed to 100 kGy, showed the highest mechanical strength and thermal stability.

A Case Study on Stratified Settlement and Rebound Characteristics due to Dewatering in Shanghai Subway Station

PubMed Central

Wang, Jianxiu; Huang, Tianrong; Sui, Dongchang

2013-01-01

Based on the Yishan Metro Station Project of Shanghai Metro Line number 9, a centrifugal model test was conducted to investigate the behavior of stratified settlement and rebound (SSR) of Shanghai soft clay caused by dewatering in deep subway station pit. The soil model was composed of three layers, and the dewatering process was simulated by self-invention of decompressing devise. The results indicate that SSR occurs when the decompression was carried out, and only negative rebound was found in sandy clay, but both positive and negative rebound occurred in the silty clay, and the absolute value of rebound in sandy clay was larger than in silty clay, and the mechanism of SSR was discussed with mechanical sandwich model, and it was found that the load and cohesive force of different soils was the main source of different responses when decompressed. PMID:23878521

Factors Affecting the Design of Slow Release Formulations of Herbicides Based on Clay-Surfactant Systems. A Methodological Approach

PubMed Central

Galán-Jiménez, María del Carmen; Mishael, Yael-Golda; Nir, Shlomo; Morillo, Esmeralda; Undabeytia, Tomás

2013-01-01

A search for clay-surfactant based formulations with high percentage of the active ingredient, which can yield slow release of active molecules is described. The active ingredients were the herbicides metribuzin (MZ), mesotrione (MS) and flurtamone (FL), whose solubilities were examined in the presence of four commercial surfactants; (i) neutral: two berols (B048, B266) and an alkylpolyglucoside (AG6202); (ii) cationic: an ethoxylated amine (ET/15). Significant percent of active ingredient (a.i.) in the clay/surfactant/herbicide formulations could be achieved only when most of the surfactant was added as micelles. MZ and FL were well solubilized by berols, whereas MS by ET/15. Sorption of surfactants on the clay mineral sepiolite occurred mostly by sorption of micelles, and the loadings exceeded the CEC. Higher loadings were determined for B266 and ET/15. The sorption of surfactants was modeled by using the Langmuir-Scatchard equation which permitted the determination of binding coefficients that could be used for further predictions of the sorbed amounts of surfactants under a wide range of clay/surfactant ratios. A possibility was tested of designing clay-surfactant based formulations of certain herbicides by assuming the same ratio between herbicides and surfactants in the formulations as for herbicides incorporated in micelles in solution. Calculations indicated that satisfactory FL formulations could not be synthesized. The experimental fractions of herbicides in the formulations were in agreement with the predicted ones for MS and MZ. The validity of this approach was confirmed in in vitro release tests that showed a slowing down of the release of a.i. from the designed formulations relative to the technical products. Soil dissipation studies with MS formulations also showed improved bioactivity of the clay-surfactant formulation relative to the commercial one. This methodological approach can be extended to other clay-surfactant systems for encapsulation and slow release of target molecules of interest. PMID:23527087

The correlation between albumin levels with 30 days mortality in community acquired pneumonia patients

NASA Astrophysics Data System (ADS)

Damayanti, N.; Abidin, A.; Keliat, E. N.

2018-03-01

The assessment of level severity ofCommunity-Acquired Pneumonia (CAP) patient at the early admission to the hospital is critical because it will determine the severity of the disease and the subsequent management of the plan. Albumin can be used as a biomarker to assess the severity of CAP. To identify the correlation between albumin level at early admission in hospital with 30-day mortality in patients with CAP. It was a cohort study. We had examined of 50 CAP subject with theCURB-65 score (Confusion, Urea, Respiratory rate, Blood pressure, Age >65years), albumin, sputum culture at the early admission at Emergency Room (ER). Then, albumin levels associated with 30-day mortality was assessed using Chi-Square test. Analysis with chi-square test found a significant correlation between albumin level with 30-day mortality (p=0.001) and Relative Risk was 2.376 (95% CI 1.515-3.723). It means that patients with CAP who has severe hypoalbuminemia have a higher risk ofdying in 30 days with 2,376 times more significant than patients with mild to moderate hypoalbuminemia. In conclusion, albumin levels at early admission in the hospital correlate with 30-day mortality in CAP patients.

Predicting pneumococcal community-acquired pneumonia in the emergency department: evaluation of clinical parameters.

PubMed

Huijts, S M; Boersma, W G; Grobbee, D E; Gruber, W C; Jansen, K U; Kluytmans, J A J W; Kuipers, B A F; Palmen, F; Pride, M W; Webber, C; Bonten, M J M

2014-12-01

The aim of this study was to quantify the value of clinical predictors available in the emergency department (ED) in predicting Streptococcus pneumoniae as the cause of community-acquired pneumonia (CAP). A prospective, observational, cohort study of patients with CAP presenting in the ED was performed. Pneumococcal aetiology of CAP was based on either bacteraemia, or S. pneumoniae being cultured from sputum, or urinary immunochromatographic assay positivity, or positivity of a novel serotype-specific urinary antigen detection test. Multivariate logistic regression was used to identify independent predictors and various cut-off values of probability scores were used to evaluate the usefulness of the model. Three hundred and twenty-eight (31.0%) of 1057 patients with CAP had pneumococcal CAP. Nine independent predictors for pneumococcal pneumonia were identified, but the clinical utility of this prediction model was disappointing, because of low positive predictive values or a small yield. Clinical criteria have insufficient diagnostic capacity to predict pneumococcal CAP. Rapid antigen detection tests are needed to diagnose S. pneumoniae at the time of hospital admission. © 2014 The Authors Clinical Microbiology and Infection © 2014 European Society of Clinical Microbiology and Infectious Diseases.

7 CFR 58.129 - Cleanliness.

Code of Federal Regulations, 2010 CFR

2010-01-01

... outer garments and caps (paper caps, hard hats, or hair nets acceptable) shall be worn to adequately protect the hair and beards when grown by all persons engaged in receiving, testing, processing milk...

7 CFR 58.129 - Cleanliness.

Code of Federal Regulations, 2014 CFR

2014-01-01

... outer garments and caps (paper caps, hard hats, or hair nets acceptable) shall be worn to adequately protect the hair and beards when grown by all persons engaged in receiving, testing, processing milk...

7 CFR 58.129 - Cleanliness.

Code of Federal Regulations, 2012 CFR

2012-01-01

... outer garments and caps (paper caps, hard hats, or hair nets acceptable) shall be worn to adequately protect the hair and beards when grown by all persons engaged in receiving, testing, processing milk...

7 CFR 58.129 - Cleanliness.

Code of Federal Regulations, 2013 CFR

2013-01-01

... outer garments and caps (paper caps, hard hats, or hair nets acceptable) shall be worn to adequately protect the hair and beards when grown by all persons engaged in receiving, testing, processing milk...

7 CFR 58.129 - Cleanliness.

Code of Federal Regulations, 2011 CFR

2011-01-01

... outer garments and caps (paper caps, hard hats, or hair nets acceptable) shall be worn to adequately protect the hair and beards when grown by all persons engaged in receiving, testing, processing milk...

Effect of clay content and mineralogy on frictional sliding behavior of simulated gouges: binary and ternary mixtures of quartz, illite, and montmorillonite

USGS Publications Warehouse

Tembe, Sheryl; Lockner, David A.; Wong, Teng-Fong

2010-01-01

We investigated the frictional sliding behavior of simulated quartz-clay gouges under stress conditions relevant to seismogenic depths. Conventional triaxial compression tests were conducted at 40 MPa effective normal stress on saturated saw cut samples containing binary and ternary mixtures of quartz, montmorillonite, and illite. In all cases, frictional strengths of mixtures fall between the end-members of pure quartz (strongest) and clay (weakest). The overall trend was a decrease in strength with increasing clay content. In the illite/quartz mixture the trend was nearly linear, while in the montmorillonite mixtures a sigmoidal trend with three strength regimes was noted. Microstructural observations were performed on the deformed samples to characterize the geometric attributes of shear localization within the gouge layers. Two micromechanical models were used to analyze the critical clay fractions for the two-regime transitions on the basis of clay porosity and packing of the quartz grains. The transition from regime 1 (high strength) to 2 (intermediate strength) is associated with the shift from a stress-supporting framework of quartz grains to a clay matrix embedded with disperse quartz grains, manifested by the development of P-foliation and reduction in Riedel shear angle. The transition from regime 2 (intermediate strength) to 3 (low strength) is attributed to the development of shear localization in the clay matrix, occurring only when the neighboring layers of quartz grains are separated by a critical clay thickness. Our mixture data relating strength degradation to clay content agree well with strengths of natural shear zone materials obtained from scientific deep drilling projects.

Experimental study of clay-hydrocarbon interactions relevant to the biodegradation of the Deepwater Horizon oil from the Gulf of Mexico.

PubMed

Warr, Laurence N; Friese, André; Schwarz, Florian; Schauer, Frieder; Portier, Ralph J; Basirico, Laura M; Olson, Gregory M

2016-11-01

Adding clay to marine oil pollution represents a promising approach to enhance bacterial hydrocarbon degradation in nutrient poor waters. In this study, three types of regionally available clays (Ca-bentonite, Fuller's Earth and kaolin) were tested to stimulate the biodegradation of source and weathered oil collected from the Deepwater Horizon spill. The weathered oil showed little biodegradation prior to experimentation and was extensively degraded by bacteria in the laboratory in a similar way as the alkane-rich source oil. For both oils, the addition of natural clay-flakes showed minor enhancement of oil biodegradation compared to the non-clay bearing control, but the clay-oil films did limit evaporation. Only alkanes of a molecular weight (MW) > 420 showed significant reduction by enhanced biodegradation following natural clay treatment. In contrast, all fertilized clay flakes showed major bacterial degradation of the oil, with a 6-10 times reduction in alkane content, and an up to 8 fold increase in the rate of O2 consumption. Compared to the control, such treatment showed particular reduction of longer chained alkanes (MW > 226). The application of natural and fertilized clay flakes also showed selective reduction of PAHs, mainly in the MW range of 200-300, but without significant change in the toxicity indices measured. These results imply that a large variety of clays may be used to boost oil biodegradation by aiding attachment of fertilizing nutrients to the oil. Copyright © 2016 Elsevier Ltd. All rights reserved.

Zeta Potential Measurements on Three Clays from Turkey and Effects of Clays on Coal Flotation

PubMed

Hussain; Dem&idot;rc&idot;; özbayoğlu

1996-12-25

There is a growing trend of characterizing coal and coal wastes in order to study the effect of clays present in them during coal washing. Coarse wastes from the Zonguldak Coal Washery, Turkey, were characterized and found to contain kaolinite, illite, and chlorite. These three clays, obtained in almost pure form from various locations in Turkey, have been subjected to X-ray diffraction (XRD) analysis to assess their purity and zeta potential measurements in order to evaluate their properties in terms of their surface charge and point of zero charge (pzc) values. It was found from XRD data that these clays were almost pure and their electrokinetic potential should therefore be representative of their colloidal behavior. All three clay minerals were negatively charged over the range from pH 2.5 to 11. Chlorite and illite have pzc at pH 3 and pH 2.5, respectively, whereas kaolinite has no pzc. The effect of these clays in Zonguldak coal, wastes, and black waters on coal flotation was studied by floating artificial mixtures of Zonguldak clean coal (4.5% ash) and individual clay. The flotation tests on coal/individual clay revealed that each clay influences coal flotation differently according to its type and amount. Illite had the worst effect on coal floated, followed by chlorite and kaolinite. The loss of yield in coal was found to be 18% for kaolinite, 20% for chlorite, and 28% for illite, indicating the worst effect of illite and least for kaolinite during coal flotation.

A comparative analysis of green synthesis approach starch capped metal oxides (ZnO & CdO) nanoparticles and its bacterial activity

NASA Astrophysics Data System (ADS)

Vidhya, K.; Devarajan, V. P.; Viswanathan, C.; Nataraj, D.; Bhoopathi, G.

2013-06-01

In this study, we have investigated the bacterial activity of starch capped ZnO & CdO NPs. The NPs were prepared through green technique under room temperature and then obtained samples were characterized by using XRD and PL techniques. XRD pattern confirms the crystal nature it shows hexagonal structure for ZnO NPs and monoclinic structure for CdO NPs and their average particle size is ±20 nm. Further, the optical properties of NPs were investigated using PL technique in which the starch capped ZnO NPs shows maximum emission at 440 nm whereas starch capped CdO NPs shows maximum emission at 545 nm. Finally, toxic test was performed with E.coli bacteria and their results were investigated. Hence, starch capped ZnO NPs induced less killing effect when compared with starch capped CdO NPs. Therefore, we conclude that the starch capped ZnO NPs may be less toxic to microorganisms when compared with starch capped CdO NPs. In addition, starch capped ZnO NPs is also suitable for anti-microbial activity.

Use of geological mapping tools to improve the hydraulic performance of SuDS.

PubMed

Bockhorn, Britta; Klint, Knud Erik Strøyberg; Jensen, Marina Bergen; Møller, Ingelise

2015-01-01

Most cities in Denmark are situated on low permeable clay rich deposits. These sediments are of glacial origin and range among the most heterogeneous, with hydraulic conductivities spanning several orders of magnitude. This heterogeneity has obvious consequences for the sizing of sustainable urban drainage systems (SuDS). We have tested methods to reveal geological heterogeneity at field scale to identify the most suitable sites for the placement of infiltration elements and to minimize their required size. We assessed the geological heterogeneity of a clay till plain in Eastern Jutland, Denmark measuring the shallow subsurface resistivity with a geoelectrical multi-electrode system. To confirm the resistivity data we conducted a spear auger mapping. The exposed sediments ranged from clay tills over sandy clay tills to sandy tills and correspond well to the geoelectrical data. To verify the value of geological information for placement of infiltration elements we carried out a number of infiltration tests on geologically different areas across the field, and we observed infiltration rates two times higher in the sandy till area than in the clay till area, thus demonstrating that the hydraulic performance of SuDS can be increased considerably and oversizing avoided if field geological heterogeneity is revealed before placing SuDS.

Geological and geotechnical characteristics of Metro Manila volcanic soils and their suitability for landfill soil liner

NASA Astrophysics Data System (ADS)

Mendoza, Edna Patricia; Catane, Sandra; Pascua, Chelo; Zarco, Mark Albert

2010-05-01

Due to the Philippines's island-arc setting, andesitic tuff and volcanic ash constitute two-thirds of the country's agricultural land. In situ weathering of these volcanic sediments produces volcanic soils. Metro Manila volcanic soils were studied to determine their suitability for landfill soil liner. The soils were analyzed using XRD and XRF, and were tested for geotechnical properties. The results show the presence of the smectite group, a swelling variety of clay. The smectite-type clays are weathering products of volcanic glasses which are dominant components of the parental rocks. The high amounts of Al2O3 indicate an Al-rich type of soil. The clay species is either di- or tri-octahedral type, which points to montmorillonite as the main clay species. Swelling clay lowers the permeability of soils and reduces the infiltration and lateral movement of leachates in the ground. Also, geotechnical tests revealed moderate to high plasticity indices and low hydraulic conductivity values. The study shows that the physicochemical characteristics of volcanic soils meet the criteria for a soil liner for future sanitary landfill projects as mandated by RA 9003, a recently ratified solid waste management act of the Philippines. Being widespread, volcanic soils can be viewed as an important resource of the country.

Cytotoxicity and mutagenicity studies on migration extracts from nanocomposites with potential use in food packaging.

PubMed

Maisanaba, Sara; Pichardo, Silvia; Jordá-Beneyto, María; Aucejo, Susana; Cameán, Ana M; Jos, Ángeles

2014-04-01

Clays are used in the food packaging industry to obtain nanocomposites. The use of these new materials is a concern, because they could reach consumers by oral exposure through possible migration, and potential toxic effects could be derived. In the present study, several in vitro basal cytotoxicity and mutagenicity tests on migration extracts obtained from a nanocomposite material with poly (lactic) acid (PLA) and two modified clays, Clay1 and Clay2, are shown. Migration extracts in distilled water showed values of 0.1 ± 0.2mg/dm(2) in all samples. Also, the content of characteristic metals of the clays structure (Al, Ca, Mg, Fe, Si) was studied and no statistical differences were observed. For the cytotoxicity assays, the human intestinal Caco-2 and human liver HepG2 cells were selected. Cells were exposed to concentrations between 2.5% and 100% extracts determining three different biomarkers of cellular viability. No significant differences were observed in the cytotoxicity assays. Finally, mutagenicity was evaluated by the Ames test and resulted in the absence of mutagenic response at all the concentrations assayed. Taking in account all above mentioned, these new materials show a good profile for their use in food packaging although further research is still needed. Copyright © 2014 Elsevier Ltd. All rights reserved.

Calcium Phosphate Bioceramics: A Review of Their History, Structure, Properties, Coating Technologies and Biomedical Applications.

PubMed

Eliaz, Noam; Metoki, Noah

2017-03-24

Calcium phosphate (CaP) bioceramics are widely used in the field of bone regeneration, both in orthopedics and in dentistry, due to their good biocompatibility, osseointegration and osteoconduction. The aim of this article is to review the history, structure, properties and clinical applications of these materials, whether they are in the form of bone cements, paste, scaffolds, or coatings. Major analytical techniques for characterization of CaPs, in vitro and in vivo tests, and the requirements of the US Food and Drug Administration (FDA) and international standards from CaP coatings on orthopedic and dental endosseous implants, are also summarized, along with the possible effect of sterilization on these materials. CaP coating technologies are summarized, with a focus on electrochemical processes. Theories on the formation of transient precursor phases in biomineralization, the dissolution and reprecipitation as bone of CaPs are discussed. A wide variety of CaPs are presented, from the individual phases to nano-CaP, biphasic and triphasic CaP formulations, composite CaP coatings and cements, functionally graded materials (FGMs), and antibacterial CaPs. We conclude by foreseeing the future of CaPs.

Calcium Phosphate Bioceramics: A Review of Their History, Structure, Properties, Coating Technologies and Biomedical Applications

PubMed Central

Eliaz, Noam; Metoki, Noah

2017-01-01

Calcium phosphate (CaP) bioceramics are widely used in the field of bone regeneration, both in orthopedics and in dentistry, due to their good biocompatibility, osseointegration and osteoconduction. The aim of this article is to review the history, structure, properties and clinical applications of these materials, whether they are in the form of bone cements, paste, scaffolds, or coatings. Major analytical techniques for characterization of CaPs, in vitro and in vivo tests, and the requirements of the US Food and Drug Administration (FDA) and international standards from CaP coatings on orthopedic and dental endosseous implants, are also summarized, along with the possible effect of sterilization on these materials. CaP coating technologies are summarized, with a focus on electrochemical processes. Theories on the formation of transient precursor phases in biomineralization, the dissolution and reprecipitation as bone of CaPs are discussed. A wide variety of CaPs are presented, from the individual phases to nano-CaP, biphasic and triphasic CaP formulations, composite CaP coatings and cements, functionally graded materials (FGMs), and antibacterial CaPs. We conclude by foreseeing the future of CaPs. PMID:28772697

Cryopyrin-associated periodic syndromes: development of a patient-reported outcomes instrument to assess the pattern and severity of clinical disease activity.

PubMed

Hoffman, Hal M; Wolfe, Frederick; Belomestnov, Pavel; Mellis, Scott J

2008-09-01

Development of an instrument for characterization of symptom patterns and severity in patients with cryopyrin-associated periodic syndromes (CAPS). Two generations of daily health assessment forms (DHAFs) were evaluated in this study. The first-generation DHAF queried 11 symptoms. Analyses of results obtained with that instrument identified five symptoms included in a revised second-generation DHAF that was tested for internal consistency and test-retest reliability. This DHAF was also assessed during the initial portion of a phase 3 clinical study of CAPS treatment. Forty-eight CAPS patients provided data for the first-generation DHAFs. Five symptoms (rash, fever, joint pain, eye redness/pain, and fatigue) were included in the revised second-generation DHAF. Symptom severity was highly variable during all study phases with as many as 89% of patients reporting at least one symptom flare, and percentages of days with flares reaching 58% during evaluation of the second-generation instrument. Mean composite key symptom scores (KSSs) computed during evaluation of the second-generation DHAF correlated well with Physician's Global Assessment of Disease Activity (r=0.91, p<0.0001) and patient reports of limitations of daily activities (r=0.68, p<0.0001). Test-retest reliability and Cronbach's alpha's were high (0.93 and 0.94, respectively) for the second-generation DHAF. Further evaluation of this DHAF during a baseline period and placebo treatment in a phase 3 clinical study of CAPS patients indicated strong correlations between baseline KSS and Physician's Global Assessment of Disease Activity. Cronbach's alpha's at baseline and test-retest reliability were also high. Potentially important study limitations include small sample size, the lack of a standard tool for CAPS symptom assessment against which to validate the DHAF, and no assessment of the instrument's responsivity to CAPS therapy. The DHAF is a new instrument that may be useful for capturing symptom patterns and severity in CAPS patients and monitoring responses to therapies for these conditions.

Strain Rate and Stress Relaxation Effects on Pressuremeter Testing in Clays

DTIC Science & Technology

1992-03-01

CHARACTERISTICS OF KAOLINITE AND GROUND SILICA 245 APPENDIX E COMPUTER PROGRAMS ....................... 248 0 0 0 0 0 0 0 iv LIST OF TABLES Table Page 3.1 A...Comparison of Three Types of Boundary Conditions in a Multiaxial Cubical Test Apparatus ................... 37 3.2 Properties of the Kaolinite and Kaolin...to 0.01 %/min Versus Strain Rate for Kaolinite Clay ................... 102 4.3 Shear Strength Normalized with Respect to 0.01 %/min Versus Strain Rate

Assessing behind armor blunt trauma in accordance with the National Institute of Justice Standard for Personal Body Armor Protection using finite element modeling.

PubMed

Roberts, Jack C; Ward, Emily E; Merkle, Andrew C; O'Connor, James V

2007-05-01

To assess the possibility of injury as a result of behind armor blunt trauma (BABT), a study was undertaken to determine the conditions necessary to produce the 44-mm clay deformation as set forth in the National Institute of Justice (NIJ) Standard 0101.04. These energy levels were then applied to a three-dimensional Human Torso Finite Element Model (HTFEM) with soft armor vest. An examination will be made of tissue stresses to determine the effects of the increased kinetic energy levels on the probability of injury. A clay finite element model (CFEM) was created with a material model that required nonlinear properties for clay. To determine these properties empirically, the results from the CFEM were matched with experimental drop tests. A soft armor vest was modeled over the clay to create a vest over clay block finite element model (VCFEM) and empirical methods were again used to obtain material properties for the vest from experimental ballistic testing. Once the properties for the vest and clay had been obtained, the kinetic energy required to produce a 44-mm deformation in the VCFEM was determined through ballistic testing. The resulting kinetic energy was then used in the HTFEM to evaluate the probability of BABT. The VCFEM, with determined clay and vest material properties, was exercised with the equivalent of a 9-mm (8-gm) projectile at various impact velocities. The 44-mm clay deformation was produced with a velocity of 785 m/s. This impact condition (9-mm projectile at 785 m/s) was used in ballistic exercises of the HTFEM, which was modeled with high-strain rate human tissue properties for the organs. The impact zones were over the sternum anterior to T6 and over the liver. The principal stresses in both soft and hard tissue at both locations exceeded the tissue tensile strength. This study indicates that although NIJ standard 0101.04 may be a good guide to soft armor failure, it may not be as good a guide in BABT, especially at large projectile kinetic energies. Further studies, both numerical and experimental, are needed to assist in predicting injury using the NIJ standard.

Hygrothermal behavior for a clay brick wall

NASA Astrophysics Data System (ADS)

Allam, R.; Issaadi, N.; Belarbi, R.; El-Meligy, M.; Altahrany, A.

2018-06-01

In Egypt, the clay brick is the common building materials which are used. By studying clay brick walls behavior for the heat and moisture transfer, the efficient use of the clay brick can be reached. So, this research studies the hygrothermal transfer in this material by measuring the hygrothermal properties and performing experimental tests for a constructed clay brick wall. We present the model for the hygrothermal transfer in the clay brick which takes the temperature and the vapor pressure as driving potentials. In addition, this research compares the presented model with previous models. By constructing the clay brick wall between two climates chambers with different boundary conditions, we can validate the numerical model and analyze the hygrothermal transfer in the wall. The temperature and relative humidity profiles within the material are measured experimentally and determined numerically. The numerical and experimental results have a good convergence with 3.5% difference. The surface boundary conditions, the ground effect, the infiltration from the closed chambers and the material heterogeneity affects the results. Thermal transfer of the clay brick walls reaches the steady state very rapidly than the moisture transfer. That means the effect of using only the external brick wall in the building in hot climate without increase the thermal resistance for the wall, will add more energy losses in the clay brick walls buildings. Also, the behavior of the wall at the heat and mass transfer calls the three-dimensional analysis for the whole building to reach the real behavior.

Hygrothermal behavior for a clay brick wall

NASA Astrophysics Data System (ADS)

Allam, R.; Issaadi, N.; Belarbi, R.; El-Meligy, M.; Altahrany, A.

2018-01-01

In Egypt, the clay brick is the common building materials which are used. By studying clay brick walls behavior for the heat and moisture transfer, the efficient use of the clay brick can be reached. So, this research studies the hygrothermal transfer in this material by measuring the hygrothermal properties and performing experimental tests for a constructed clay brick wall. We present the model for the hygrothermal transfer in the clay brick which takes the temperature and the vapor pressure as driving potentials. In addition, this research compares the presented model with previous models. By constructing the clay brick wall between two climates chambers with different boundary conditions, we can validate the numerical model and analyze the hygrothermal transfer in the wall. The temperature and relative humidity profiles within the material are measured experimentally and determined numerically. The numerical and experimental results have a good convergence with 3.5% difference. The surface boundary conditions, the ground effect, the infiltration from the closed chambers and the material heterogeneity affects the results. Thermal transfer of the clay brick walls reaches the steady state very rapidly than the moisture transfer. That means the effect of using only the external brick wall in the building in hot climate without increase the thermal resistance for the wall, will add more energy losses in the clay brick walls buildings. Also, the behavior of the wall at the heat and mass transfer calls the three-dimensional analysis for the whole building to reach the real behavior.

Tailoring the mechanical properties of SU-8/clay nanocomposites: polymer microcantilever fabrication perspective

NASA Astrophysics Data System (ADS)

Chen, Hao; Ojijo, Vincent; Cele, Hastings; Joubert, Trudi; Suprakas, Sinha Ray; Land, Kevin

2014-06-01

SU-8/Clay nanocomposite is considered as a candidate material for microcantilever sensor fabrication. Organically modified montmorillonite clay nanoparticles are dispersed in the universally used negative photoresist polymer SU-8, for a low cost material, which is also biocompatible. If varying the clay loading of the composite material yields a variation of the Young's modulus, the tailored material stiffness presents an opportunity for fabrication of microcantilevers with tunable sensor sensitivity. With this microcantilever application perspective, mechanical and thermal properties of the material were investigated. SU-8/Clay nanocomposite samples were prepared with clay loadings from 1wt% - 10wt%. Tensile test results show a general trend of increase in composite modulus with an increase in the clay loading up to 7wt%, followed by a small drop at 10wt%. The composite material indeed yields moderate variation of the Young's modulus. It was also found that the thermal degradation peak of the material occurred at 300°C, which is beyond the operating temperature of typical microcantilever sensor applications. The fabrication of a custom designed microcantilever array chip with the SU-8/Clay nanocomposite material was achieved in a class 100 cleanroom, using spin-coating and photolithography microfabrication techniques. The optimization of the process for fabricating microcantilever with the SU-8/Clay nanocomposite material is discussed in this paper. The results of this research are promising for cheaper mass production of low cost disposable, yet sensitive, microcantilever sensor elements, including biosensor applications.

Organoclay hybrid materials as precursors of porous ZnO/silica-clay heterostructures for photocatalytic applications.

PubMed

Akkari, Marwa; Aranda, Pilar; Ben Haj Amara, Abdessalem; Ruiz-Hitzky, Eduardo

2016-01-01

In this study, ZnO/SiO 2 -clay heterostructures were successfully synthesized by a facile two-step process applied to two types of clays: montmorillonite layered silicate and sepiolite microfibrous clay mineral. In the first step, intermediate silica-organoclay hybrid heterostructures were prepared following a colloidal route based on the controlled hydrolysis of tetramethoxysilane in the presence of the starting organoclay. Later on, pre-formed ZnO nanoparticles (NP) dispersed in 2-propanol were incorporated under ultrasound irradiation to the silica-organoclay hybrid heterostructures dispersed in 2-propanol, and finally, the resulting solids were calcinated to eliminate the organic matter and to produce ZnO nanoparticles (NP) homogeneously assembled to the clay-SiO 2 framework. In the case of montmorillonite the resulting materials were identified as delaminated clays of ZnO/SiO 2 -clay composition, whereas for sepiolite, the resulting heterostructure is constituted by the assembling of ZnO NP to the sepiolite-silica substrate only affecting the external surface of the clay. The structural and morphological features of the prepared heterostructures were characterized by diverse physico-chemical techniques (such as XRD, FTIR, TEM, FE-SEM). The efficiency of these new porous ZnO/SiO 2 -clay heterostructures as potential photocatalysts in the degradation of organic dyes and the removal of pharmaceutical drugs in water solution was tested using methylene blue and ibuprofen compounds, respectively, as model of pollutants.

College of American Pathologists' laboratory standards for next-generation sequencing clinical tests.

PubMed

Aziz, Nazneen; Zhao, Qin; Bry, Lynn; Driscoll, Denise K; Funke, Birgit; Gibson, Jane S; Grody, Wayne W; Hegde, Madhuri R; Hoeltge, Gerald A; Leonard, Debra G B; Merker, Jason D; Nagarajan, Rakesh; Palicki, Linda A; Robetorye, Ryan S; Schrijver, Iris; Weck, Karen E; Voelkerding, Karl V

2015-04-01

The higher throughput and lower per-base cost of next-generation sequencing (NGS) as compared to Sanger sequencing has led to its rapid adoption in clinical testing. The number of laboratories offering NGS-based tests has also grown considerably in the past few years, despite the fact that specific Clinical Laboratory Improvement Amendments of 1988/College of American Pathologists (CAP) laboratory standards had not yet been developed to regulate this technology. To develop a checklist for clinical testing using NGS technology that sets standards for the analytic wet bench process and for bioinformatics or "dry bench" analyses. As NGS-based clinical tests are new to diagnostic testing and are of much greater complexity than traditional Sanger sequencing-based tests, there is an urgent need to develop new regulatory standards for laboratories offering these tests. To develop the necessary regulatory framework for NGS and to facilitate appropriate adoption of this technology for clinical testing, CAP formed a committee in 2011, the NGS Work Group, to deliberate upon the contents to be included in the checklist. Results . -A total of 18 laboratory accreditation checklist requirements for the analytic wet bench process and bioinformatics analysis processes have been included within CAP's molecular pathology checklist (MOL). This report describes the important issues considered by the CAP committee during the development of the new checklist requirements, which address documentation, validation, quality assurance, confirmatory testing, exception logs, monitoring of upgrades, variant interpretation and reporting, incidental findings, data storage, version traceability, and data transfer confidentiality.

76 FR 57696 - Approval and Promulgation of Implementation Plans; New York; Motor Vehicle Enhanced Inspection...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-16

..., oxygen sensor, heated oxygen sensor, and exhaust gas recirculation or EGR system) while the remaining...: Emissions Test Type: light-duty vehicles ( 18,000 lbs. ECD Checks for or gas cap checks). GVWR), 25 MYs old..., CAT, EVAP system disablement. Gas Cap: NYTEST Pressure Test. Note: The reader is referred to the...

Emergent Literacy: A Comparison of Formal and Informal Assessment Methods.

ERIC Educational Resources Information Center

Harlin, Rebecca; Lipa, Sally

1990-01-01

Compares the effectiveness of the Concepts about Print (CAP) Test and the Metropolitan Readiness Test (MRT) in assessing the literacy development of both normal and at-risk primary students. Finds the CAP to be an effective predictor for at-risk children. Finds the MRT not worth the time, effort, and cost of administration. (RS)

Test results of Thermal Ice Cap prototype and final comments. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burley, W.

1982-01-01

The design and testing of an insulating cover, Ice Cap, for an ice rink are described. The radio-controlled reel system which houses, deploys, and harvests the 17,000 square feet of insulating material is essential to the success of the cover. Photographs showing the use of the system are included. (MHR)

Kindergarten Knowledge of Print Conventions and Later School Achievement: A Five-Year Follow-Up.

ERIC Educational Resources Information Center

Day, Kaaren C.; Day, H. D.

1984-01-01

Administered the Concepts About Print (CAP) test during kindergarten and first grade (N=56). Results showed the CAP to be highly correlated with various tests of school achievement obtained during the second through the fourth grades and to effectively predict those children who would later be retained in school. (JAC)

Effectiveness of 13-Valent Pneumococcal Conjugate Vaccine Against Hospitalization for Community-Acquired Pneumonia in Older US Adults: A Test-Negative Design.

PubMed

McLaughlin, John M; Jiang, Qin; Isturiz, Raul E; Sings, Heather L; Swerdlow, David L; Gessner, Bradford D; Carrico, Ruth M; Peyrani, Paula; Wiemken, Timothy L; Mattingly, William A; Ramirez, Julio A; Jodar, Luis

2018-05-21

Following universal recommendation for use of 13-valent pneumococcal conjugate vaccine (PCV13) in US adults aged ≥65 years in September 2014, we conducted the first real-world evaluation of PCV13 vaccine effectiveness (VE) against hospitalized vaccine-type community-acquired pneumonia (CAP) in this population. Using a test-negative design, we identified cases and controls from a population-based surveillance study of adults in Louisville, Kentucky, who were hospitalized with CAP. We analyzed a subset of CAP patients enrolled 1 April 2015 through 30 April 2016 who were aged ≥65 years and consented to have their pneumococcal vaccination history confirmed by health insurance records. Cases were defined as hospitalized CAP patients with PCV13 serotypes identified via culture or serotype-specific urinary antigen detection assay. Remaining CAP patients served as test-negative controls. Of 2034 CAP hospitalizations, we identified PCV13 serotypes in 68 (3.3%) participants (ie, cases), of whom 6 of 68 (8.8%) had a positive blood culture. Cases were less likely to be immunocompromised (29.4% vs 46.4%, P = .02) and overweight or obese (41.2% vs 58.6%, P = .01) compared to controls, but were otherwise similar. Cases were less likely to have received PCV13 than controls (3/68 [4.4%] vs 285/1966 [14.5%]; unadjusted VE, 72.8% [95% confidence interval, 12.8%-91.5%]). No confounding was observed during adjustment for patient characteristics, including immunocompromised status, body mass index, and history of influenza and pneumococcal polysaccharide vaccination (adjusted VE range, 71.1%-73.3%). Our study is the first to demonstrate real-world effectiveness of PCV13 against vaccine-type CAP in adults aged ≥65 years following introduction into a national immunization program.

Synthesis and characterization of immobilized Ni-Co bimetallic using Tapanuli clay for catalyst application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nuryanti,; Juwono, Ariadne L., E-mail: ariadne@sci.ui.ac.id; Krisnandi, Yuni K.

2016-04-19

Heterogeneous catalysts hold various advantages, namely, easy to separate from their products, reusable and regarded as environmental friendly materials. The synthesis of immobilized Ni monometallic, Co monometallic and Ni-Co bimetallic by Tapanuli clay were carried out using intercalation method. Firstly, the synthesis of Na-Bentonite was conducted to provide sufficient area to immobilize bimetal in the clay interlayer. Secondly, Ni, Co and Ni-Co were immobilized in the Tapanuli clay interlayer. Several techniques, such as X-Ray Diffraction, Fourier Transform Infra Red and Energy Dispersive X-Ray Analysis were applied to characterize and compare the properties of the synthesized materials. The results showed thatmore » the insertion of Ni, Co and Ni-Co in the clay interlayer occurred through a cation exchange reaction. The Energy Dispersive X-Ray analysis for Ni-Co bimetallic showed that the immobilized Ni and Co in the clay is in the ratio of 1:1. Catalytic test with Gas Chromatography showed that Ni-Co bimetallic generates a higher yield percentage compared to Ni and Co monometallic.« less

Test of superplastically formed corrugated aluminum compression specimens with beaded webs

NASA Technical Reports Server (NTRS)

Davis, Randall C.; Royster, Dick M.; Bales, Thomas T.; James, William F.; Shinn, Joseph M., Jr.

1991-01-01

Corrugated wall sections provide a highly efficient structure for carrying compressive loads in aircraft and spacecraft fuselages. The superplastic forming (SPF) process offers a means to produce complex shells and panels with corrugated wall shapes. A study was made to investigate the feasibility of superplastically forming 7475-T6 aluminum sheet into a corrugated wall configuration and to demonstrate the structural integrity of the construction by testing. The corrugated configuration selected has beaded web segments separating curved-cap segments. Eight test specimens were fabricated. Two specimens were simply a single sheet of aluminum superplastically formed to a beaded-web, curved-cap corrugation configuration. Six specimens were single-sheet corrugations modified by adhesive bonding additional sheet material to selectively reinforce the curved-cap portion of the corrugation. The specimens were tested to failure by crippling in end compression at room temperature.

Gas breakthrough and emission through unsaturated compacted clay in landfill final cover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ng, C.W.W.; Chen, Z.K.; Coo, J.L.

Highlights: • Explore feasibility of unsaturated clay as a gas barrier in landfill cover. • Gas breakthrough pressure increases with clay thickness and degree of saturation. • Gas emission rate decreases with clay thickness and degree of saturation. • A 0.6 m-thick clay layer may be sufficient to meet gas emission rate limit. - Abstract: Determination of gas transport parameters in compacted clay plays a vital role for evaluating the effectiveness of soil barriers. The gas breakthrough pressure has been widely studied for saturated swelling clay buffer commonly used in high-level radioactive waste disposal facility where the generated gas pressuremore » is very high (in the order of MPa). However, compacted clay in landfill cover is usually unsaturated and the generated landfill gas pressure is normally low (typically less than 10 kPa). Furthermore, effects of clay thickness and degree of saturation on gas breakthrough and emission rate in the context of unsaturated landfill cover has not been quantitatively investigated in previous studies. The feasibility of using unsaturated compacted clay as gas barrier in landfill covers is thus worthwhile to be explored over a wide range of landfill gas pressures under various degrees of saturation and clay thicknesses. In this study, to evaluate the effectiveness of unsaturated compacted clay to minimize gas emission, one-dimensional soil column tests were carried out on unsaturated compacted clay to determine gas breakthrough pressures at ultimate limit state (high pressure range) and gas emission rates at serviceability limit state (low pressure range). Various degrees of saturation and thicknesses of unsaturated clay sample were considered. Moreover, numerical simulations were carried out using a coupled gas–water flow finite element program (CODE-BRIGHT) to better understand the experimental results by extending the clay thickness and varying the degree of saturation to a broader range that is typical at different climate conditions. The results of experimental study and numerical simulation reveal that as the degree of saturation and thickness of clay increase, the gas breakthrough pressure increases but the gas emission rate decreases significantly. Under a gas pressure of 10 kPa (the upper bound limit of typical landfill gas pressure), a 0.6 m or thicker compacted clay is able to prevent gas breakthrough at degree of saturation of 60% or above (in humid regions). Furthermore, to meet the limit of gas emission rate set by the Australian guideline, a 0.6 m-thick clay layer may be sufficient even at low degree of saturation (i.e., 10% like in arid regions)« less

The differential impact of clerk interest and participation in a child and adolescent psychiatry clerkship rotation upon psychiatry and pediatrics residency matches.

PubMed

Hanson, Mark D; Szatmari, Peter; Eva, Kevin W

2011-01-01

The authors evaluated the differential impact of clerk interest and participation in a Child and Adolescent Psychiatry (CAP) clerkship rotation upon psychiatry and pediatrics residency matches. Authors studied clerks from the McMaster University M.D. program graduating years of 2005-2007. Participants were categorized as 1) clerks with CAP clerkship interest and CAP clerkship participation; 2) clerks with CAP clerkship interest but without CAP clerkship participation; and 3) clerks with neither CAP clerkship interest nor CAP clerkship participation. The outcome variable was residency matches, with Psychiatry and Pediatrics residency matches highlighted. Descriptive statistics were used, and chi-squared tests performed to compare proportions of residency matches across these three clerkship groups. Residency matches of 390 clerks were reviewed. CAP clerkship interest was expressed by 23.9% of clerks. Comparison across the two CAP clerkship interest groups revealed match rates to Psychiatry and Pediatrics not to be significantly different, although the proportion of each match was significantly different from the third clerkship group (without CAP clerkship interest) in both instances. CAP clerkship interest, but not participation, was associated with Psychiatry and Pediatrics residency matches. CAP clerkship interest among clerks presents recruitment and educational opportunities; a recruitment opportunity for clerks heading toward a Psychiatry residency, and an educational opportunity for clerks heading toward a Pediatrics residency.

Optical Properties of Synthesized Nanoparticles ZnS Using Methacrylic Acid as the Capping Agent

NASA Astrophysics Data System (ADS)

Nazerdeylami, Somayeh; Saievar Iranizad, Esmaiel; Molaei, Mehdi

Optical analysis (UV-vis spectroscopy) of solution of ZnS nanoparticles prepared at room temperature by a chemical capping method using methacrylic acid (MAA) capping agent at concentration of 0.05, 0.2, 0.5 and 1.17 molar is investigated. The spectroscopy results indicate increasing of band gap of ZnS through increasing concentration of the methacrylic acid as capping agent in the solution. According to the relation of Effective Mass Approximation, it is concluded that the size of nanoparticles decreased with the increasing concentration of the capping agent in the tested solutions. The size of the particles is found to be in 1.77-2.05 nm range.

Psychophysics, flare, and neurosecretory function in human pain models: capsaicin versus electrically evoked pain.

PubMed

Geber, Christian; Fondel, Ricarda; Krämer, Heidrun H; Rolke, Roman; Treede, Rolfe-Detlef; Sommer, Claudia; Birklein, Frank

2007-06-01

Intradermal capsaicin injection (CAP) and electrical current stimulation (ES) are analyzed in respect to patterns and test-retest reliability of pain as well as sensory and neurosecretory changes. In 10 healthy subjects, 2x CAP (50 microg) and 2x ES (5 to 30 mA) were applied to the volar forearm. The time period between 2 identical stimulations was about 4 months. Pain ratings, areas of mechanical hyperalgesia, and allodynia were assessed. The intensity of sensory changes was quantified by using quantitative sensory testing. Neurogenic flare was assessed by using laser Doppler imaging. Calcitonin gene-related peptide (CGRP) release was quantified by dermal microdialysis in combination with an enzyme immunoassay. Time course and peak pain ratings were different between CAP and ES. Test-retest correlation was high (r > or = 0.73). Both models induced primary heat hyperalgesia and primary plus secondary pin-prick hyperalgesia. Allodynia occurred in about half of the subjects. Maximum flare sizes did not differ between CAP and ES, but flare intensities were higher for ES. Test-retest correlation was higher for flare sizes than for flare intensity. A significant CGRP release could only be measured after CAP. The different time courses of pain stimulation (CAP: rapidly decaying pain versus ES: pain plateau) led to different peripheral neurosecretory effects but induced similar central plasticity and hyperalgesia. The present study gives a detailed overview of psychophysical and neurosecretory characteristics induced by noxious stimulation with capsaicin and electrical current. We describe differences, similarities, and reproducibility of these human pain models. These data might help to interpret past and future results of human pain studies using experimental pain.

Desorption and mobility mechanisms of co-existing polycyclic aromatic hydrocarbons and heavy metals in clays and clay minerals.

PubMed

Saeedi, Mohsen; Li, Loretta Y; Grace, John R

2018-05-15

The effects of soil components such as clay minerals and as humic acids, as well as co-existing metals and polycyclic aromatic hydrocarbons, on desorption and mobility are examined. Three types of artificially blended clay and clay mineral mixtures (pure kaolinite, kaolinite + sand and kaolinite + sand + bentonite), each with different humic acid content, were tested for desorption and mobility of acenaphthene, fluorene and fluoranthene by three extracting solutions CaCl 2 (0.01 M) and EDTA (0.01M) with non-ionic surfactants (Tween 80 and Triton X100). Heavy metals (Ni, Pb and Zn) were also studied for desorption and mobility. The influence of co-present metals on simultaneous desorption and mobility of PAHs was investigated as well. The results showed that <10% of metals in the clay mineral mixtures were mobile. Combined EDTA and non-ionic solutions can enhance the desorption and mobility of PAHs to >80% in clay mineral mixtures containing no sand, while in the same soils containing ∼40% sand, the desorption exceeded 90%. Heavy metals, as well as increasing humic acids content in the clay mineral mixtures, decreased the desorption and mobility of PAHs, especially for soils containing no sand, and for fluoranthene compared with fluorene and acenaphthene. Copyright © 2018 Elsevier Ltd. All rights reserved.

Fault-related clay authigenesis along the Moab Fault: Implications for calculations of fault rock composition and mechanical and hydrologic fault zone properties

USGS Publications Warehouse

Solum, J.G.; Davatzes, N.C.; Lockner, D.A.

2010-01-01

The presence of clays in fault rocks influences both the mechanical and hydrologic properties of clay-bearing faults, and therefore it is critical to understand the origin of clays in fault rocks and their distributions is of great importance for defining fundamental properties of faults in the shallow crust. Field mapping shows that layers of clay gouge and shale smear are common along the Moab Fault, from exposures with throws ranging from 10 to ???1000 m. Elemental analyses of four locations along the Moab Fault show that fault rocks are enriched in clays at R191 and Bartlett Wash, but that this clay enrichment occurred at different times and was associated with different fluids. Fault rocks at Corral and Courthouse Canyons show little difference in elemental composition from adjacent protolith, suggesting that formation of fault rocks at those locations is governed by mechanical processes. Friction tests show that these authigenic clays result in fault zone weakening, and potentially influence the style of failure along the fault (seismogenic vs. aseismic) and potentially influence the amount of fluid loss associated with coseismic dilation. Scanning electron microscopy shows that authigenesis promotes that continuity of slip surfaces, thereby enhancing seal capacity. The occurrence of the authigenesis, and its influence on the sealing properties of faults, highlights the importance of determining the processes that control this phenomenon. ?? 2010 Elsevier Ltd.

Combined Mini-Cylex & Disk Acceleration Tests in Type K Copper.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maines, Warren Russell; Kittell, David E.; Hobbs, Michael L.

We combined the miniature cylinder expansion test (Mini-Cylex), with the Disk Acceleration Test (DAX) using Type K copper, Picatinny Liquid Explosive, and photonic Doppler velocimetry. We estimated the CJ state using plate reverberation methods at the test cap. We extracted velocities at 2, 7, and 10 volume expansions to fit Jones-Wilkins-Lee Equation of State at the tube wall. And we estimated Gurney velocity both at the test cap and tube wall. Our experiments and simulations are within expected uncertainty. The test and the analysis effectively reduce costs while keeping similar fidelity compared with more expensive tests.

Ford-Class Aircraft Carrier: Congress Should Consider Revising Cost Cap Legislation to Include All Construction Costs

DTIC Science & Technology

2014-11-01

thus increasing the likelihood of additional testing delays. For example, testing of the ship’s fire sprinklers was delayed because construction of...not deploy as scheduled or will deploy without fully tested systems . The Navy is implementing steps to achieve the $11.5 billion congressional cost...cap, by postponing installation of some systems until after ship delivery, and deferring an estimated $200 million - $250 million in previously

Solid Rocket Booster Hydraulic Pump Port Cap Joint Load Testing

NASA Technical Reports Server (NTRS)

Gamwell, W. R.; Murphy, N. C.

2004-01-01

The solid rocket booster uses hydraulic pumps fabricated from cast C355 aluminum alloy, with 17-4 PH stainless steel pump port caps. Corrosion-resistant steel, MS51830 CA204L self-locking screw thread inserts are installed into C355 pump housings, with A286 stainless steel fasteners installed into the insert to secure the pump port cap to the housing. In the past, pump port cap fasteners were installed to a torque of 33 Nm (300 in-lb). However, the structural analyses used a significantly higher nut factor than indicated during tests conducted by Boeing Space Systems. When the torque values were reassessed using Boeing's nut factor, the fastener preload had a factor of safety of less than 1, with potential for overloading the joint. This paper describes how behavior was determined for a preloaded joint with a steel bolt threaded into steel inserts in aluminum parts. Finite element models were compared with test results. For all initial bolt preloads, bolt loads increased as external applied loads increased. For higher initial bolt preloads, less load was transferred into the bolt, due to external applied loading. Lower torque limits were established for pump port cap fasteners and additional limits were placed on insert axial deformation under operating conditions after seating the insert with an initial preload.

The effect of cap lamp lighting on postural control and stability

PubMed Central

Sammarco, John J.; Pollard, Jonisha P.; Porter, William L.; Dempsey, Patrick G.; Moore, Caitlin T.

2015-01-01

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are conducting mine illumination research with the objective of improving miner safety. Slips, trips, and falls (STFs) are the second leading accident class (18.1%, n = 2,374) of nonfatal lost-time injuries at underground mines (MSHA, 2005–2009). Factors contributing to STFs include recognition of hazards as well as postural balance and age. Improved lighting may enable better hazard recognition and reduce the impact of postural balance and age. Previous research has shown that cap lamp technology that used light-emitting diodes (LEDs) has improved hazard detection. This study was an initial investigation to determine if cap lamp lighting significantly influences measures of static postural stability (displacement and velocity of center of pressure). Results of this investigation showed no significant differences in the balance measures of interest between cap lamps tested. However, balance was shown to significantly decline (p < 0.05) when tested in an underground coal mine compared to the laboratory testing condition. Relevance to industry: Underground coal mine workers wear cap lamps on their hard hats as their primary light source to illuminate nearby areas where their vision is directed. Proper illumination may improve miner safety by improving their STF hazard recognition and balance. PMID:26472917

2002 Hyperspectral Analysis of Hazardous Waste Sites on the Savannah River Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gladden, J.B.

2003-08-28

Hazardous waste site inspection is a labor intensive, time consuming job, performed primarily on the ground using visual inspection and instrumentation. It is an expensive process to continually monitor hazardous waste and/or landfill sites to determine if they are maintaining their integrity. In certain instances, it may be possible to monitor aspects of the hazardous waste sites and landfills remotely. The utilization of multispectral data was suggested for the mapping of clays and iron oxides associated with contaminated groundwater, vegetation stress, and methane gas emissions (which require longer wavelength detectors). The Savannah River Site (SRS) near Aiken, S.C. is amore » United States Department of Energy facility operated by the Westinghouse Savannah River Company. For decades the SRS was responsible for developing weapons grade plutonium and other materials for the nation's nuclear defense. Hazardous waste was generated during this process. Waste storage site inspection is a particularly important issue at the SRS because there are over 100 hazardous waste sites scattered throughout the 300 mile complex making it difficult to continually monitor all of the facilities. The goal is to use remote sensing technology to identify surface anomalies on the hazardous waste sites as early as possible so that remedial work can take place rapidly to maintain the integrity of the storage sites. The anomalous areas are then targeted for intensive in situ human examination and measurement. During the 1990s, many of the hazardous waste sites were capped with protective layers of polyethelene sheeting and soil, and planted with bahia grass and/or centipede grass. This research investigated hyperspectral remote sensing technology to determine if it can be used to measure accurately and monitor possible indicators of change on vegetated hazardous waste sites. Specifically, it evaluated the usefulness of hyperspectral remote sensing to assess the condition of vegetation on clay- caps on the Mixed Waste Management Facility (MWMF). This report first describes the principles of hyperspectral remote sensing. In situ measurement and hyperspectral remote sensing methods used to analyze hazardous waste sites on the Savannah River Site are then presented.« less

Field Performance Of A Compacted Clay Landfill Final Cover At A Humid Site

EPA Science Inventory

A study was conducted in southern Georgia, USA, to evalaute how the hydraulic properties of the compacted clay barrier layer in a final landfill cover changed over a 4-year service life. The cover was part of a test section constructed in a large drainage lysimeter that allowed ...

Links between Children's Clay Models and School Achievement.

ERIC Educational Resources Information Center

Bezruczko, Nikolaus

Two studies examined the relationship between children's clay models and the children's concurrent school achievement, and compared a 6-year longitudinal record of achievement test scores for one cohort of students at schools that did or did not provide visual arts instruction. Participating in Study 1 were 201 kindergartners and third graders…

Use of natural clays as sorbent materials for rare earth ions: Materials characterization and set up of the operative parameters.

PubMed

Iannicelli-Zubiani, Elena Maria; Cristiani, Cinzia; Dotelli, Giovanni; Gallo Stampino, Paola; Pelosato, Renato; Mesto, Ernesto; Schingaro, Emanuela; Lacalamita, Maria

2015-12-01

Two mineral clays of the montmorillonite group were tested as sorbents for the removal of Rare Earths (REs) from liquid solutions. Lanthanum and neodymium model solutions were used to perform uptake tests in order to: (a) verify the clays sorption capability, (b) investigate the sorption mechanisms and (c) optimize the experimental parameters, such as contact time and pH. The desorption was also studied, in order to evaluate the feasibility of REs recovery from waters. The adsorption-desorption procedure with the optimized parameters was also tested on a leaching solution obtained by dissolution of a dismantled NdFeB magnet of a hard-disk. The clays were fully characterized after REs adsorption and desorption by means of X-ray powder diffraction (XRPD) and X-ray photoelectron spectroscopy (XPS); the liquid phase was characterized via Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES) analyses. The experimental results show that both clays are able to capture and release La and Nd ions, with an ion exchange mechanism. The best total efficiency (capture ≈ 50%, release ≈ 70%) is obtained when the uptake and release processes are performed at pH=5 and pH=1 respectively; in real leached scrap solutions, the uptake is around 40% but release efficiency is strongly decreased passing from a mono-ion system to a real system (from 80% to 5%). Furthermore, a strong matrix effect is found, with the matrix largely affecting both the uptake and the release of neodymium. Copyright © 2015 Elsevier Ltd. All rights reserved.

Strength and Stiffness Development in Soft Soils: A FESEM aided Soil Microstructure Viewpoint

NASA Astrophysics Data System (ADS)

Wijeyesekera, D. C.; Ho, M. H.; Bai, X.; Bakar, I.

2016-07-01

This paper opens with an overview of the debatable definition of soft soil that goes beyond a (CH) organic / inorganic clay and OH peat to include weakly cemented periglacial deposits of loess and alike. It then outlines the findings obtained from stiffness test on cement-stabilised soft clay. The findings are complemented with a microstructure viewpoint obtained using field emission scanning electron microscope (FESEM). Research also comprised of making cylindrical stabilised clay samples, prepared in the laboratory with various rubber chips contents and cement, and then aged for 28 days. The samples were then subjected to unconfined compressive strength (UCS) test and observations were also made of its microstructure using the FESEM. The impact of the soil microstructure on the stiffness result was studied both with the stabilized soil and also of some of the natural undisturbed loess soils. Sustainability aspect and the potential of the use of rubber chips and sand as additives to cement stabilisation are also discussed. The overall test results indicated that rubber chips and sand contributed to the improvement in unconfined compressive strength (qu). The derogatory influence of moisture on the stiffness of the stabilised clay was studied simultaneously. SEM micrographs are presented that show bonding of cement, rubber chips/ sand and soft clay, granular units and aggregated / agglomerated units in loess. The paper concludes with observations on the dependence of soil microstructure on the soil strength and deformability and even collapsibility of the loess. Current practices adopted as engineering solutions to these challenging soils are outlined.

Testing Orbital Parameters as a Hypothesis for the Presence of CO2 Deposits on Mars's South Pole

NASA Astrophysics Data System (ADS)

Bain, Z. M.; Bierson, C. J.

2017-12-01

Observational data of Mars's polar caps shows large deposits of buried CO2 ice in the south polar cap and only seasonal CO2 ice in the north [1]. The lower elevation of Mars's north pole leads to higher surface pressures and therefore more favorable conditions for CO2 ice deposition. There are a few plausible reasons why the CO2 deposits are observed at the southern cap. The first is that during a past epochs of atmospheric collapse, CO2was deposited at both poles and only preserved in the south. Another is that the deposits represent a period where ice was preferentially deposited at the south polar cap. The latter could occur if the orbital parameters were such that the southern cap experienced colder summers (less insolation) than the north. The model of Bierson et. al. 2016 [2] used the observed difference in albedo between the north and the south polar caps and found several periods in the last one million years where deposition was favored at the south polar cap. Here we test if deposition is still favored in the south using the same albedo for both caps. For this work we are using the seasonally resolved KRC model [3]. We varied obliquity, longitude of perihelion, and eccentricity to match their expected values over the last one million years [4]. We modeled the annual CO2 deposition rate in 1,000 year increments. We tested both constant and insolation dependent albedo that was the same at both poles. While we did find periods of deposition on the south pole, this was always in conjunction with deposition in the north in much greater amounts. This finding favors the hypothesis that the deposits are only observed in the southern cap due to the deep pre-existing troughs that allowed the CO2 to be preserved to the modern day. These results also highlight the importance of understanding the observed difference in albedo between the polar caps. [1] Phillips et al. (2011) AAAS, Vol.332 Is.6031 pp.838-841 [2] Bierson et al. (2016) GRL, Vol.43 Is.9 pp.4172-4179 [3] Kieffer (2013) JGR, Vol.118 Is.3 pp.451-470 [4] Laskar et al. (2004) Icarus, Vol.170 Is.2 pp.343-364

Automatic Quality Inspection of Percussion Cap Mass Production by Means of 3D Machine Vision and Machine Learning Techniques

NASA Astrophysics Data System (ADS)

Tellaeche, A.; Arana, R.; Ibarguren, A.; Martínez-Otzeta, J. M.

The exhaustive quality control is becoming very important in the world's globalized market. One of these examples where quality control becomes critical is the percussion cap mass production. These elements must achieve a minimum tolerance deviation in their fabrication. This paper outlines a machine vision development using a 3D camera for the inspection of the whole production of percussion caps. This system presents multiple problems, such as metallic reflections in the percussion caps, high speed movement of the system and mechanical errors and irregularities in percussion cap placement. Due to these problems, it is impossible to solve the problem by traditional image processing methods, and hence, machine learning algorithms have been tested to provide a feasible classification of the possible errors present in the percussion caps.

Holocene surge-history of the Eyjabakkajökull glacier inferred from varved lake sediments on eastern Iceland

NASA Astrophysics Data System (ADS)

Striberger, J.; Bjorck, S.; Ingolfsson, O.; Kjaer, K.; Snowball, I.; Uvo, C. B.

2009-12-01

Properties of varved lake sediments from Lake Lögurinn on eastern Iceland and their link to glacial processes of Eyjabakkajökull, a surging outlet glacier of the Vatnajökull ice cap, is examined. An 18 m long sediment sequence obtained from the lake, covering at least the past ~ 9 200 years, displays a distinct recurring pattern of light-coloured clay dominated laminae sections. The thickness of the light-coloured laminae is mainly controlled by the amount of glacial rock flour transported from Eyjabakkajökull. These light laminae are interlaid by coarser dark-coloured laminae mainly formed by suspended matter transported to the lake by the large non-glacial river Grímsá. During the recent surge of Eyjabakkajökull in 1972, the amount of suspended matter transported to the lake increased significantly. The surge was followed by years of recurring drainages of Lake Háöldulón, an ice-dammed lake that was formed shortly after the surge. As a result, the amount of glacial rock flour transported to Lake Lögurinn was higher than usual as long as Lake Háöldulón continued to drain (i.e. as long as the ice front was in an advanced position enough to dam the lake). This increase in glacially derived rock flour is reflected in the sediments, as the varve that was formed in 1972 constitutes the thickest light-coloured laminae deposited during the 20th century, which is followed by the second thickest light-coloured laminae, deposited in 1973. From there on, the thicknesses of the light-coloured laminae gradually fade out. Based on these modern observations, we suggest that the recurring cyclic pattern of light-coloured clay dominated laminae sections in the sediment sequence is related to past surges of Eyjabakkajökull, followed by drainages of Lake Háöldulón. Recurring cycles of light-coloured clay dominated laminae began to develop close to the Hekla-3 and Hekla-4 tephras (ca. 3000-4000 years BP), which also coincides with the time when the varves became more distinct. Further down in the sequence, the recurring cycles of light-coloured laminae are not found and any varves are in general diffuse or missing. Hypothetically, the reason for this might be that the suspended matter delivered from the glacier was transported elsewhere at this time. However, based on the large-scale morphology of the area, we find it more likely that Eyjabakkajökull, and thus parts of, or the whole Vatnajökull ice cap, was smaller or perhaps not present during the mid-Holocene and thus had little or no influence on the sedimentation in Lake Lögurinn.

Use of borehole geophysical logs for improved site characterization at Naval Weapons Industrial Reserve Plant, Dallas, Texas

USGS Publications Warehouse

Anaya, Roberto; Braun, Christopher L.; Kuniansky, Eve L.

2000-01-01

A shallow alluvial aquifer at the Naval Weapons Industrial Reserve Plant near Dallas, Texas, has been contaminated by organic solvents used in the fabrication and assembly of aircraft and aircraft parts. Natural gamma-ray and electromagnetic-induction log data collected during 1997 from 162 wells were integrated with existing lithologic and cone-penetrometer test log data to improve characterization of the subsurface alluvium at the site. The alluvium, consisting of mostly fine-grained, low-permeability sediments, was classified into low, intermediate, and high clay-content sediments on the basis of the gamma-ray logs. Low clay-content sediments were interpreted as being relatively permeable, whereas high clay-content sediments were interpreted as being relatively impermeable. Gamma-ray logs, cone-penetrometer test logs, and electromagnetic-induction logs were used to develop a series of intersecting sections to delineate the spatial distribution of low, intermediate, and high clay-content sediments and to delineate zones of potentially contaminated sediments. The sections indicate three major sedimentary units in the shallow alluvial aquifer at NWIRP. The lower unit consists of relatively permeable, low clay-content sediments and is absent over the southeastern and northwestern part of the site. Permeable zones in the complex, discontinuous middle unit are present mostly in the western part of the site. In the eastern and southeastern part of the site, the upper unit has been eroded away and replaced by fill material. Zones of potentially contaminated sediments are generally within the uppermost clay layer or fill material. In addition, the zones tend to be local occurrences.

Selectivity sequences and sorption capacities of phosphatic clay and humus rich soil towards the heavy metals present in zinc mine tailing.

PubMed

Chaturvedi, Pranav Kumar; Seth, Chandra Shekhar; Misra, Virendra

2007-08-25

Sorption efficacy of phosphatic clay and humus rich soil alone and on combination were tested towards heavy metals present in zinc mine tailing (Zawar Zinc Mine), Udaipur (India). Characterization of the zinc mine tailing sample indicated the presence of Pb, Cu, Zn and Mn in the concentration of 637, 186, 720 and 577microg(-1), respectively. For sorption efficacy, the zinc mine tailing soil were properly amended with phosphatic clay and humus rich soil separately and in combination and leachability study was performed by batch experiment at different pH range from 3 to 9. The data showed that the percent leachability of heavy metal in non-amended soil was 75-90%. After amendment with phosphatic clay percent leachability of heavy metals became 35-45%. Further, the addition of humus soil to phosphatic clay decreased the percent leachability up to 5-15% at all tested pH. Column leachability experiment was performed to evaluate the rate of leachability. The shape of cumulative curves of Pb, Cu, Zn and Mn showed an increase in its concavity in following order: PbCu>Zn>Mn. Further, Langmuir isotherms applied for the sorption studies indicated that phosphatic clay in the presence of humus soil had high affinity for Pb followed by Cu, Zn and Mn, with sorption capacities (b) 139.94, 97.02, 83.32 and 67.58microgg(-1), respectively.

Closure Report for Corrective Action Unit 516: Septic Systems and Discharge Points

DOE Office of Scientific and Technical Information (OSTI.GOV)

NSTec Environmental Restoration

Corrective Action Unit (CAU) 516 is located in Areas 3, 6, and 22 of the Nevada Test Site. CAU 516 is listed in the Federal Facility Agreement and Consent Order of 1996 as Septic Systems and Discharge Points, and is comprised of six Corrective Action Sites (CASs): {sm_bullet} CAS 03-59-01, Bldg 3C-36 Septic System {sm_bullet} CAS 03-59-02, Bldg 3C-45 Septic System {sm_bullet} CAS 06-51-01, Sump and Piping {sm_bullet} CAS 06-51-02, Clay Pipe and Debris {sm_bullet} CAS 06-51-03, Clean Out Box and Piping {sm_bullet} CAS 22-19-04, Vehicle Decontamination Area The Nevada Division of Environmental Protection (NDEP)-approved corrective action alternative for CASsmore » 06-51-02 and 22-19-04 is no further action. The NDEP-approved corrective action alternative for CASs 03-59-01, 03-59-02, 06-51-01, and 06-51-03 is clean closure. Closure activities included removing and disposing of total petroleum hydrocarbon (TPH)-impacted septic tank contents, septic tanks, distribution/clean out boxes, and piping. CAU 516 was closed in accordance with the NDEP-approved CAU 516 Corrective Action Plan (CAP). The closure activities specified in the CAP were based on the recommendations presented in the CAU 516 Corrective Action Decision Document (U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, 2004). This Closure Report documents CAU 516 closure activities. During closure activities, approximately 186 tons of hydrocarbon waste in the form of TPH-impacted soil and debris, as well as 89 tons of construction debris, were generated and managed and disposed of appropriately. Waste minimization techniques, such as field screening of soil samples and the utilization of laboratory analysis to characterize and classify waste streams, were employed during the performance of closure work.« less

Testing Pneumonia Vaccines in the Elderly: Determining a Case Definition for Pneumococcal Pneumonia in the Absence of a Gold Standard.

PubMed

Jokinen, Jukka; Snellman, Marja; Palmu, Arto A; Saukkoriipi, Annika; Verlant, Vincent; Pascal, Thierry; Devaster, Jeanne-Marie; Hausdorff, William P; Kilpi, Terhi M

2018-06-01

Clinical assessments of vaccines to prevent pneumococcal community-acquired pneumonia (CAP) require sensitive and specific case definitions, but there is no gold standard diagnostic test. To develop a new case definition suitable for vaccine efficacy studies, we applied latent class analysis (LCA) to the results from 7 diagnostic tests for pneumococcal etiology on clinical specimens from 323 elderly persons with radiologically confirmed pneumonia enrolled in the Finnish Community-Acquired Pneumonia Epidemiology study during 2005-2007. Compared with the conventional use of LCA, which is mainly to determine sensitivities and specificities of different tests, we instead used LCA as an appropriate instrument to predict the probability of pneumococcal etiology for each CAP case based on individual test profiles, and we used the predictions to minimize the sample size that would be needed for a vaccine efficacy trial. When compared with the conventional laboratory criteria of encapsulated pneumococci in culture, in blood culture or high-quality sputum culture, or urine antigen positivity, our optimized case definition for pneumococcal CAP resulted in a trial sample size that was almost 20,000 subjects smaller. We believe that the novel application of LCA detailed here to determine a case definition for pneumococcal CAP could also be similarly applied to other diseases without a gold standard.

In vitro and in vivo assessment of cellular permeability and pharmacodynamics of S-nitrosylated Captopril, a nitric oxide donor

PubMed Central

Jia, Lee; Wong, Hong

2001-01-01

The present studies were aimed at testing the hypothesis that S-nitrosylated captopril (CapNO), a novel crystalline nitric oxide (NO) donor, readily permeates both in vitro and in vivo endothelial monolayers, resulting in its pharmacodynamic effects. CapNO and Captopril (Cap) were added to apical side of endothelial monolayers formed on microporous membranes, and the permeated drugs were collected from basolateral side and detected by a HPLC method. The permeability coefficient (Papp; cm sec−1) of CapNO across the endothelial monolayers was 6.0×10−5, higher than that of Cap (3.13×10−5), indicating the enhancement effect of the attached NO group in CapNO on cellular permeability. The Papp of CapNO and Cap across Caco-2 cells were 3.15×10−5 and 1.53×10−5, respectively. The low Papp of CapNO to Caco-2 cells may be attributed to the high membrane resistance of Caco-2 cells. A bolus injection of CapNO to epicardial coronary artery of chronically-instrumented awake dogs caused significant increases in coronary blood flow and coronary diameters dose-dependently without significant changes in aortic pressure. In contrast, the equimolar doses of Cap did not produce haemodynamic responses. Intravenous CapNO caused an instant increase in the regional cerebral blood flow determined by H2-clearance, whereas the equimolar doses of Cap did not enhance the cerebral blood flow. These results conclude that the NO group, an active component of CapNO, enhances both in vitro and in vivo endothelial permeability to the entire compound, resulting in instant increases in blood flow and vascular diameters. In contrast, the equimolar Cap does not have the instant vascular effects. PMID:11739246

In vitro and in vivo assessment of cellular permeability and pharmacodynamics of S-nitrosylated captopril, a nitric oxide donor.

PubMed

Jia, L; Wong, H

2001-12-01

1. The present studies were aimed at testing the hypothesis that S-nitrosylated captopril (CapNO), a novel crystalline nitric oxide (NO) donor, readily permeates both in vitro and in vivo endothelial monolayers, resulting in its pharmacodynamic effects. 2. CapNO and Captopril (Cap) were added to apical side of endothelial monolayers formed on microporous membranes, and the permeated drugs were collected from basolateral side and detected by a HPLC method. The permeability coefficient (P(app); cm sec(-1)) of CapNO across the endothelial monolayers was 6.0 x 10(-5), higher than that of Cap (3.13 x 10(-5)), indicating the enhancement effect of the attached NO group in CapNO on cellular permeability. The P(app) of CapNO and Cap across Caco-2 cells were 3.15 x 10(-5) and 1.53 x 10(-5), respectively. The low P(app) of CapNO to Caco-2 cells may be attributed to the high membrane resistance of Caco-2 cells. 3. A bolus injection of CapNO to epicardial coronary artery of chronically-instrumented awake dogs caused significant increases in coronary blood flow and coronary diameters dose-dependently without significant changes in aortic pressure. In contrast, the equimolar doses of Cap did not produce haemodynamic responses. 4. Intravenous CapNO caused an instant increase in the regional cerebral blood flow determined by H(2)-clearance, whereas the equimolar doses of Cap did not enhance the cerebral blood flow. 5. These results conclude that the NO group, an active component of CapNO, enhances both in vitro and in vivo endothelial permeability to the entire compound, resulting in instant increases in blood flow and vascular diameters. In contrast, the equimolar Cap does not have the instant vascular effects.

The cervical cap.

PubMed

1988-10-07

The US Food and Drug Administration has approved marketing of the Prentif cavity-rim cervical cap. This contraceptive device is being distributed in the US and Canada by Cervical Cap Ltd, Los Gatos, California. The Prentif cap is available in 4 sizes: 22, 25, 28, and 31 mm inside diameter, with a length of 1 1/4-1 1/2 inches. In a multicenter trial involving 522 diaphragm users and 581 cap users followed for 2 years, the cap was 82.6% effective and the diaphragm was 83.3% effective in preventing pregnancy. When pregnancies attributable to user failure were excluded, these rates were increased to 93.6% for the cap and 95.4% for the diaphragm. 4% of cap users compared with only 1.7% of diaphragm users in this study developed abnormal Pap smears after 3 months of use; in addition, a higher proportion of cap users became infected with Gardnerella vaginalis and Monilia. Theoretical hazards include toxic shock syndrome and endometriosis due to backflow of menstrual fluids. Cap users are advised to undergo a Pap test after 3 months of use and discontinue cap use if the results are abnormal. The cap should not be used during menstruation. Although the cap can be left in place for up to 48 hours, its position should be checked before and after each episode of intercourse. The cervical cap requires less spermicide than the diaphragm and is not as messy. In addition, it can be left in the vagina twice as long as the diaphragm, without additional spermicide. Since the cap is smaller than the diaphragm and does not cover the vaginal wall, some women find intercourse more pleasurable with this device.

The influence of total suction on the brittle failure characteristics of clay shales

NASA Astrophysics Data System (ADS)

Amann, F.; Linda, W.; Zimmer, S.; Thoeny, R.

2013-12-01

Clay shale testing is challenging and the results obtained from standard laboratory tests may not always reflect the strength of the clay shale in-situ. This is to a certain extend associated with the sensitivity of these rock types to desaturation processes during drilling, sample storage, and sample preparation. In this study the relationship between total suction, uniaxial compressive strength and Brazilian tensile (BTS) strength of cylindrical samples of Opalinus Clay was established in a systematic manner. Unconfined uniaxial compression and BTS tests were performed utilizing a servo-controlled testing procedure. Total suctions in the specimens was generated in air tight desiccators using supersaturated saline solutions which establish a relative humidity ranging from 20% to 99%. For unconfined compressive strength tests loading of the specimens occurred parallel to bedding. For BTS tests loading was either oriented normal or perpendicular to bedding. Both, the crack initiation and volumetric strain reversal threshold values were determined using volumetric and radial stress-strain methods. The results of BTS tests show that the tensile strength normal and perpendicular to bedding increases by a factor of approximately 3 when total suction is increased from 0 to 90 MPa (i.e. saturation decreases from 1.0 to 0.7) . Beyond 90 MPa total suction no further increase in tensile strength was observed, most probably due to shrinkage cracks which alter the tensile strength of the clay shale. Results obtained from UCS tests suggest that higher total suctions result in higher UCS values. Between total suctions of 0 to 90 MPa, the strength increase is almost linear (i.e. the UCS increases by a factor of 1.5 MPa). Beyond 90 MPa total suction no further strength increase was observed. A similar trend can be observed for crack initiation and crack damage values. In the same range of total suction the crack initiation stress increases by a factor of 5 (from 2 MPa to 10 MPa), and the crack damage stress increases by a factor of 2 (from 6 to 12 MPa). In addition to UCS tests, the water retention curve of intact and disturbed specimens was established. Here, results indicate that the drying path remains nearly unaffected by mechanical damage. However, the wetting path is considerably affected by mechanical damage.

Excessive Cap-dependent Translation as a Molecular Mechanism Underlying ASD

DTIC Science & Technology

2012-08-01

SUPPLEMENTARY NOTES 14. ABSTRACT We hypothesize that excessive cap-dependent translation is a causative factor in autism spectrum disorder...compounds to therapeutically target eIF4E-eIF4G interactions and eIF4A for treating patients with ASD. 15. SUBJECT TERMS autism spectrum...Introduction We hypothesize that excessive cap-dependent translation is a causative factor in autism spectrum disorder (ASD). To test this

Experimental study of Human Adenoviruses interactions with clays

NASA Astrophysics Data System (ADS)

Bellou, Maria; Syngouna, Vasiliki; Paparrodopoulos, Spyros; Vantarakis, Apostolos; Chrysikopoulos, Constantinos

2014-05-01

Clays are used to establish low permeability liners in landfills, sewage lagoons, water retention ponds, golf course ponds, and hazardous waste sites. Human adenoviruses (HAdVs) are waterborne viruses which have been used as viral indicators of fecal pollution. The objective of this study was to investigate the survival of HAdV in static and dynamic clay systems. The clays used as a model were crystalline aluminosilicates: kaolinite and bentonite. The adsorption and survival of HAdVs onto these clays were characterized at two different controlled temperatures (4 and 25o C) under static and dynamic batch conditions. Control tubes, in the absence of clay, were used to monitor virus inactivation due to factors other than adsorption to clays (e.g. inactivation or sorption onto the tubes walls). For both static and dynamic batch experiments, samples were collected for a maximum period of seven days. This seven day time - period was determined to be sufficient for the virus-clay systems to reach equilibrium. To infer the presence of infectious HAdV particles, all samples were treated with Dnase and the extraction of viral nucleid acid was performed using a commercial viral RNA kit. All samples were analyzed by Real - Time PCR which was used to quantify viral particles in clays. Samples were also tested for virus infectivity by A549 cell cultures. Exposure time intervals in the range of seven days (0.50-144 hours) resulted in a load reduction of 0.74 to 2.96 logs for kaolinite and a reduction of 0.89 to 2.92 for bentonite. Furthermore, virus survival was higher onto bentonite than kaolinite (p

Capping a Pulpotomy with Calcium Aluminosilicate Cement: Comparison to Mineral Trioxide Aggregates

PubMed Central

Kramer, Phillip R.; Woodmansey, Karl F.; White, Robert; Primus, Carolyn M.; Opperman, Lynne A.

2014-01-01

Introduction Calcium aluminate cements have shown little affinity for bacterial growth, low toxicity, and immunogenicity when used as a restoration material, but calcium aluminate cements have not been tested in vivo in pulpotomy procedures. Methods To address this question, a calcium aluminate cement (Quick-Set) was tested along with 2 mineral trioxide aggregates, ProRoot MTA and MTA Plus. These cements were used as a capping agent after pulpotomy. Control rats had no pulpotomy, or the pulpotomy was not capped. Proinflammatory cytokines interleukin (IL)-1β and IL-1α were measured, and histology was performed at 30 and 60 days after capping. The nociceptive response was determined by measuring the lengthening of the rat's meal duration. Results and Conclusions: IL-1β and IL-1α concentrations were reduced in the capped teeth, but no differences were observed among the 3 cements. Dentinal bridging could be detected at both 30 and 60 days with each of the 3 cements, and the pulps were still vital 60 days after capping. Meal duration significantly shortened after placement of the 3 different cements, indicating a nociceptive response, but there were no differences among the materials. Calcium aluminate cements had similar properties to mineral trioxide aggregates and is a viable option for pulpotomy procedures. PMID:25146026

30 CFR 20.0 - Compliance with the requirements necessary for obtaining approval.

Code of Federal Regulations, 2010 CFR

2010-07-01

... LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MINE LAMPS OTHER THAN STANDARD CAP... MSHA for any electric mine lamps other than standard cap lamps a manufacturer must comply with the...

Effective control of modified palygorskite to NH4+-N release from sediment.

PubMed

Chen, Lei; Zheng, Tianyuan; Zhang, Junjie; Liu, Jie; Zheng, Xilai

2014-01-01

Sediment capping is an in situ treatment technology that can effectively restrain nutrient and pollutant release from the sediment in lakes and reservoirs. Research on sediment capping has focused on the search for effective, non-polluting and affordable capping materials. The efficiency and mechanism of sediment capping with modified palygorskite in preventing sediment ammonia nitrogen (NH4+-N) release to surface water were investigated through a series of batch and sediment capping experiments. Purified palygorskite and different types of modified palygorskite (i.e. heated, acid-modified and NaCI-modified palygorskite) were used in this investigation. Factors affecting control efficiency, including the temperature, thickness and grain size of the capping layer, were also analysed. The batch tests showed that the adsorption of NH4+-N on modified palygorskite achieved an equilibration in the initial 45 min, and the adsorption isotherm followed the Freundlich equation. Sediment capping experiments showed that compared with non-capped condition, covering the sediment with modified palygorskite and sand both inhibited NH4+-N release to the overlying water. Given its excellent chemical stability and strong adsorption, heated palygorskite, which has a NH4+-N release inhibition ratio of 41.3%, is a more effective sediment capping material compared with sand. The controlling effectiveness of the modified palygorskite increases with thicker capping layer, lower temperature and smaller grain size of the capping material.

Rigid palm oil-based polyurethane foam reinforced with diamine-modified montmorillonite nanoclay

NASA Astrophysics Data System (ADS)

Haziq Dzulkifli, Mohd; Yazid Yahya, Mohd; Majid, Rohah A.

2017-05-01

This paper presents work on organically-modified montmorillonite (MMT) nanoclay embedded in rigid palm oil-based polyurethane (PU) foam. MMT was modified with organic surfactant diamino propane (DAP). PU foam was fabricated in closed mold, and the amount of DAP-MMT was varied in each foam formulation. The obtained foam was tested for its microstructure and morphology. Appearance of peaks from infra-red spectra corresponding to N-H, C=O, and C-N confirms the formation of PU networks. Scanning electron microscopy (SEM) revealed fine, closed-cellular structure at low clay loading; increasing DAP-MMT content induced larger cell sizes with blowholes. X-ray diffraction (XRD) indicates fully-exfoliated clays at 1 wt. % and partial-exfoliation at 3 wt. % clay loading, suggesting clumping of clays as DAP-MMT content increased.

USAFSAM (USAF School of Aerospace Medicine) Review and Analysis of Radiofrequency Radiation Bioeffects Literature: Fourth Report.

DTIC Science & Technology

1984-05-01

TEST CHART ?NATIONAL BUREAU OF STANDARDS-1963-A AD)A142 961 Repor USAFSAM-TR-84-17 USAFSAM REVIEW AND ANALYSIS OF RADIOFREQUENCY RADIATION BIOEFFECTS...1983a) AUTHOR ABSTRACT: Normal mouse B lymphocytes were tested for the ability to cap plasma antigen-antibody complexes following exposure to 2.45-GHz...treatment, the irradiated cells and the nonirradiated controls were tested for capping by the direct immunofluorescence technique. First, the cells

KSC-04pd0965

NASA Image and Video Library

2004-04-28

KENNEDY SPACE CENTER, FLA. - Workers in the Orbiter Processing Facility remove Ground Support Equipment used to install Discovery’s nose cap on Friday. The nose cap had been removed from the vehicle in the summer of 2003 and returned to the vendor, where it underwent numerous forms of Non-Destructive Evaluation. These tests included X-ray, ultrasound and eddy current to ensure its structural integrity prior to installation on the vehicle. The nose cap was also recoated. Once returned to KSC, new Thermal Protection System blankets were assembled inside of the nose cap and thermography was performed prior to installation on the orbiter.

KSC-04pd0964

NASA Image and Video Library

2004-04-28

KENNEDY SPACE CENTER, FLA. - Workers in the Orbiter Processing Facility get ready to remove Ground Support Equipment used to install Discovery’s nose cap on Friday. The nose cap had been removed from the vehicle in the summer of 2003 and returned to the vendor, where it underwent numerous forms of Non-Destructive Evaluation. These tests included X-ray, ultrasound and eddy current to ensure its structural integrity prior to installation on the vehicle. The nose cap was also recoated. Once returned to KSC, new Thermal Protection System blankets were assembled inside of the nose cap and thermography was performed prior to installation on the orbiter.

Synthetic. cap alpha. subunit peptide 125-147 of human nicotinic acetylcholine receptor induces antibodies to native receptor

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCormick, D.J.; Griesmann, G.E.; Huang, Z.

1986-03-05

A synthetic peptide corresponding to residues 125-147 of the Torpedo acetylcholine receptor (AChR) ..cap alpha.. subunit proved to be a major antigenic region of the AChR. Rats inoculated with 50 ..mu..g of peptide (T ..cap alpha.. 125-147) developed T cell immunity and antibodies to native AChR and signs of experimental autoimmune myasthenia gravis. They report the synthesis and preliminary testing of a disulfide-looped peptide comprising residues 125-147 of the human AChR ..cap alpha.. subunit. Peptide H ..cap alpha.. 125-147 differs from T ..cap alpha.. 125-147 at residues 139 (Glu for Gln) and 143 (Ser for Thr). In immunoprecipitation assays, antibodiesmore » to Torpedo AChR bound /sup 125/I-labelled H..cap alpha.. 125-147 antibody bound H..cap alpha.. 125-147, but monoclonal antibodies to an immunodominant region of native AChR bound neither H..cap alpha.. 125-147 nor T ..cap alpha.. 125-147. Rats immunized with H ..cap alpha.. 125-147 produced anti-mammalian muscle AChR antibodies that induced modulation of AChRs from cultured human myotubes. Thus, region 125-147 of the human AChR ..cap alpha.. subunit is extracellular in muscle, and is both antigenic and immunogenic. It remains to be determined whether or not autoantibodies to this region may in part cause the weakness or myasthenia gravis in man.« less

Performance of the cobas Hepatitis B virus (HBV) test using the cobas 4800 system and comparison of HBV DNA quantification ability between the COBAS AmpliPrep/COBAS TaqMan HBV test version 2.0 and cobas HBV test.

PubMed

Shin, Kyung-Hwa; Lee, Hyun-Ji; Chang, Chulhun L; Kim, Hyung-Hoi

2018-04-01

Hepatitis B virus (HBV) DNA levels are used to predict the response to therapy, determine therapy initiation, monitor resistance to therapy, and establish treatment success. To verify the performance of the cobas HBV test using the cobas 4800 system for HBV DNA quantification and to compare the HBV DNA quantification ability between the cobas HBV test and COBAS AmpliPrep/COBAS TaqMan HBV version 2.0 (CAP/CTM v2.0). The precision, linearity, and limit of detection of the cobas HBV test were evaluated using the 4th World Health Organization International Standard material and plasma samples. Clinical samples that yielded quantitative results using the CAP/CTM v2.0 and cobas HBV tests were subjected to correlational analysis. Three hundred forty-nine samples were subjected to correlational analysis, among which 114 samples showed results above the lower limit of quantification. Comparable results were obtained ([cobas HBV test] = 1.038 × [CAP/CTM v2.0]-0.173, r = 0.914) in 114 samples, which yielded values above the lower limit of quantification. The results for 86.8% of the samples obtained using the cobas HBV test were within 0.5 log 10 IU/mL of the CAP/CTM v2.0 results. The total precision values against the low and high positive controls were 1.4% (mean level: 2.25 log 10 IU/mL) and 3.2% (mean level: 6.23 log 10 IU/mL), respectively. The cobas HBV test demonstrated linearity (1.15-6.75 log 10 IU/mL, y = 0.95 × 6 + 0.17, r 2  = 0.994). The cobas HBV test showed good correlation with CAP/CTM v2.0, and had good precision and an acceptable limit of detection. The cobas HBV test using the cobas 4800 is a reliable method for quantifying HBV DNA levels in the clinical setting. Copyright © 2018. Published by Elsevier B.V.

Accuracy verification and identification of matrix effects. The College of American Pathologists' Protocol.

PubMed

Eckfeldt, J H; Copeland, K R

1993-04-01

Proficiency testing using stabilized control materials has been used for decades as a means of monitoring and improving performance in the clinical laboratory. Often, the commonly used proficiency testing materials exhibit "matrix effects" that cause them to behave differently from fresh human specimens in certain clinical analytic systems. Because proficiency testing is the primary method in which regulatory agencies have chosen to evaluate clinical laboratory performance, the College of American Pathologists (CAP) has proposed guidelines for investigating the influence of matrix effects on their Survey results. The purpose of this investigation was to determine the feasibility, usefulness, and potential problems associated with this CAP Matrix Effect Analytical Protocol, in which fresh patient specimens and CAP proficiency specimens are analyzed simultaneously by a field method and a definitive, reference, or other comparative method. The optimal outcome would be that both the fresh human and CAP Survey specimens agree closely with the comparative method result. However, this was not always the case. Using several different analytic configurations, we were able to demonstrate matrix and calibration biases for several of the analytes investigated.

Capsaicin-capped silver nanoparticles: its kinetics, characterization and biocompatibility assay

NASA Astrophysics Data System (ADS)

Amruthraj, Nagoth Joseph; Preetam Raj, John Poonga; Lebel, Antoine

2015-04-01

Capsaicin was used as a bio-reductant for the reduction of silver nitrate to form silver nanoparticles. The formation of the silver nanoparticles was initially confirmed by color change and Tyndall effect of light scattering. It was characterized with UV-visible spectroscopy, FTIR and TEM. Hemagglutination (H) test and H-inhibition assay were performed in the presence of AgNPs-capsaicin conjugates. The silver colloid solution after complete reduction turned into pale gray color. The characteristic surface plasmon resonance of silver nanoparticles (SNPs) was observed at 450 nm. Time taken for complete bio-reduction of silver nitrate and capping was found to be 16 hours. The amount of capsaicin required to reduce 20 ml of 1 mM silver nitrate solution was found to be 40 μg approximately. The FTIR results confirmed the capping of capsaicin on the silver metal. The particle size was within the range of 20-30 nm. The hemagglutination and H-inhibition test was negative for all the blood groups. The capsaicin-capped silver nanoparticles were compatible with blood cells in hemagglutination test implying biocompatibility as future therapeutic drug.

Protective capping and surface passivation of III-V nanowires by atomic layer deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dhaka, Veer, E-mail: veer.dhaka@aalto.fi; Perros, Alexander; Kakko, Joona-Pekko

2016-01-15

Low temperature (∼200 °C) grown atomic layer deposition (ALD) films of AlN, TiN, Al{sub 2}O{sub 3}, GaN, and TiO{sub 2} were tested for protective capping and surface passivation of bottom-up grown III-V (GaAs and InP) nanowires (NWs), and top-down fabricated InP nanopillars. For as-grown GaAs NWs, only the AlN material passivated the GaAs surface as measured by photoluminescence (PL) at low temperatures (15K), and the best passivation was achieved with a few monolayer thick (2Å) film. For InP NWs, the best passivation (∼2x enhancement in room-temperature PL) was achieved with a capping of 2nm thick Al{sub 2}O{sub 3}. All othermore » ALD capping layers resulted in a de-passivation effect and possible damage to the InP surface. Top-down fabricated InP nanopillars show similar passivation effects as InP NWs. In particular, capping with a 2 nm thick Al{sub 2}O{sub 3} layer increased the carrier decay time from 251 ps (as-etched nanopillars) to about 525 ps. Tests after six months ageing reveal that the capped nanostructures retain their optical properties. Overall, capping of GaAs and InP NWs with high-k dielectrics AlN and Al{sub 2}O{sub 3} provides moderate surface passivation as well as long term protection from oxidation and environmental attack.« less

Preparation of hybrid nano biocomposite κ-carrageenan/cellulose nanocrystal/nanoclay

NASA Astrophysics Data System (ADS)

Zakuwan, Siti Zarina; Ahmad, Ishak; Ramli, Nazaruddin

2013-11-01

Biodegradable composites film based on κ-carrageenan and nano particles as filler was prepared to study the mechanical strength of carrageenan composites. Solution casting technique was used to prepare_this biocomposite. Preparation of composite film and nano filler involve two stages, preparation of cellulose nanocrystals (CNC) from kenaf with alkali treatment, bleaching, and hydrolysis followed by the preparation of two types of nano composite. Tensile test was carried on the composite film based on κ-carrageenan with the variation percentage of CNC and nano clay to obtain the optimum CNC and nano clay loading. After that hybrid nano-biocomposite film based on κ-carrageenan with the variation percentage of CNC/nano clay (OMMT) according to optimum value of composite carrageenan/CNC and composite carrageenan/nano clay film was prepared. The effect of nano filler on the mechanical properties of carrageenan films was examined. κ-carrageenan biocomposite increased with the optimum at 4% CNC and nano clay composition. Additional improvement of tensile strength with hybridization of CNC and nanoclay indicated better mechanical properties.

Lime as an Anti-Plasticizer for Self-Compacting Clay Concrete

PubMed Central

Landrou, Gnanli; Brumaud, Coralie; Winnefeld, Frank; Flatt, Robert J.; Habert, Guillaume

2016-01-01

This paper focuses on the modification of clay properties with inorganic additives to deflocculate and flocculate inorganic soil for the development of a material that would be as easy to use as the current concrete products, but with a much lower environmental impact. Considering that the rheological behaviour of clays is controlled by their surface charge, we first introduce potential determining ions to deflocculate the clay particles and to reduce the yield stress of the earth material. Their efficiency is characterized using zeta potential measurements and rheological tests. We then achieve the flocculation of clay particles by using natural minerals that slowly dissolve in the interstitial liquid and ultimately precipitate calcium silicate hydrate (C–S–H). The precipitation products are identified by X-ray diffraction and the consequences of this delayed precipitation are followed by oscillatory rheometric measurements. Finally, it is suggested that in this process, C–S–H precipitation is not used as a binding vector but as an anti-plasticizer that removes the inorganic dispersant additives. PMID:28773453

Lime as an Anti-Plasticizer for Self-Compacting Clay Concrete.

PubMed

Landrou, Gnanli; Brumaud, Coralie; Winnefeld, Frank; Flatt, Robert J; Habert, Guillaume

2016-04-29

This paper focuses on the modification of clay properties with inorganic additives to deflocculate and flocculate inorganic soil for the development of a material that would be as easy to use as the current concrete products, but with a much lower environmental impact. Considering that the rheological behaviour of clays is controlled by their surface charge, we first introduce potential determining ions to deflocculate the clay particles and to reduce the yield stress of the earth material. Their efficiency is characterized using zeta potential measurements and rheological tests. We then achieve the flocculation of clay particles by using natural minerals that slowly dissolve in the interstitial liquid and ultimately precipitate calcium silicate hydrate (C-S-H). The precipitation products are identified by X-ray diffraction and the consequences of this delayed precipitation are followed by oscillatory rheometric measurements. Finally, it is suggested that in this process, C-S-H precipitation is not used as a binding vector but as an anti-plasticizer that removes the inorganic dispersant additives.

Improvement of barrier properties of rotomolded PE containers with nanoclay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jamshidi, Shadi; Sundararaj, Uttandaraman, E-mail: u.sundararaj@ucalgary.ca

Polyethylene (PE) is widely used to make bulk containers in rotational molding process. The challenge in this study is to improve permeation resistance of PE to hydrocarbon solvents and gases. Adding organomodified clay improves the thermal, barrier and mechanical properties of PE. In fact, clay layers create a tortuous path against the permeant, yielding better barrier properties. Due to the non-polar hydrophobic nature of PE and polar hydrophilic structure of clay minerals, the compatibilizer plays a crucial role to enhance the dispersion level of clay in the matrix. In this study High Density Polyethylene (HDPE) and Linear Low Density Polyethylenemore » (LLDPE) layered silicate nanocomposite were melt-compounded with two concentrations of organomodified clay (2 and 4 wt. %). The interaction between nanoclay, compatibilizer and rotomolding grade of PE were examined by using X-ray diffraction, transmission electron microscopy (TEM) and rheology test. Rheology was used to determine the performance of our material at low shear processing condition.« less

Late Holocene Lake Level Fluctuations at Laguna Arapa, Peru and Connections to Human Demography

NASA Astrophysics Data System (ADS)

Hillman, A. L.; Abbott, M. B.; Werne, J. P.; Arkush, E.; Thompson, L. G.; Ferland, T.; Holmes, E.; Puhnaty, C.; Woods, A.

2016-12-01

The relationship between variations in hydroclimate and human demography on the Peruvian Altiplano has significant implications for understanding how people in the past have adapted to changes in freshwater resources. To investigate these human-environmental interactions, this project presents a 2,000 year sediment record from Laguna Arapa, a large lake that is <20 km NW of Lake Titicaca. Using sedimentology and stratigraphy as well as a suite of organic geochemical proxies including fecal 5β-stanols and leaf waxes (long chain n-alkanoic acids), we aim to tie together proxies of human population with indicators of regional hydroclimate. Preliminary results of sedimentology and stratigraphy show notable transitions from sand to silt to clay, suggesting rising lake level sequences at 500 and 700 AD. The last 1,300 years of sediment are characterized by alternating layers of organic rich material with abundant charcoal and black inorganic clay, suggesting intermittent periods of aridity and/or anthropogenic fire-setting. These layers are particularly frequent during the Medieval Climate Anomaly, which was characterized by dry and warm conditions. These results agree well with other records of hydroclimate from regional lakes as well as accumulation rate and temperature from the Quelccaya ice cap. Organic geochemical work is currently in progress and shows promise for linking together proxies of human demography with hydroclimate to understand the relationship between human settlement and climate change.

In situ chemical osmosis experiment in the Boom Clay at the Mol underground research laboratory

NASA Astrophysics Data System (ADS)

Garavito, A. M.; De Cannière, P.; Kooi, H.

Studies on the compatibility of Boom Clay with large amounts of nitrate- bearing bituminized radioactive waste have recently raised a particular interest for osmosis-induced effects in this reference formation in Belgium. Indeed, water flow and solute transport may be associated with several types of driving forces, or gradients (chemical, electrical, thermal), in addition to the hydraulic forces, resulting in the so-called coupled flows. Fluid flow caused by driving forces different than hydraulic gradients is referred to as osmosis. Chemical osmosis, the water flow induced by a chemical gradient across a semi-permeable membrane, can generate pressure increase. The question thus arises if there is a risk to create high pore pressures that could damage the near-field of medium-level waste (MLW) galleries, if osmotically driven water flows towards the galleries are produced by the release of large amounts of NaNO 3 (750 t) in the formation. To what extent a low-permeability clay formation such as the Boom Clay acts as an osmotic membrane is thus a key issue to assess the relevance of osmosis phenomena for the disposal of medium-level waste. An in situ osmosis experiment has been conducted at the H ADES underground research laboratory to determine the osmotic efficiency of Boom Clay at the field scale. A recently developed chemical osmosis flow continuum model has been used to design the osmosis experiment, and to interpret the water pressure measurements. Experimental data could be reproduced quite accurately by the model, and the inferred parameter values are consistent with independent determinations for Boom Clay. A rapid water pressure increase (but limited to about a 2 m water column) was observed after 12 h in the filter containing the more saline water. Then, the osmotically induced water pressure slowly decays on several months. So, the experimental results obtained in situ confirm the occurrence of non-hydraulic flow phenomena (chemical osmosis) in a low-permeability plastic formation such as the Boom Clay. The osmotic efficiency of Boom Clay is high under undisturbed chemical conditions ( σ = 0.41 at 0.014 M NaHCO 3), but rapidly decreases when the dissolved salts concentration increases ( σ = 0.07 at 0.14 M NaHCO 3). A semi-permeable membrane behaviour of the Boom Clay (high efficiencies) may be expected for the disposal of nitrate-bearing radioactive waste. However, the presently observed osmotically induced pressure is too low to have a significant mechanical impact on the host rock. Finally, the short duration of the osmosis test performed suggests that the shut-in test method used is effective for osmosis testing.

Y-12 Industrial Landfill V. Permit application modifications

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-09-01

This report contains the modifications in operations and design to meet the Tennessee Department of Environment and Conversation (TDEC) July 10, 1993, amendments to the regulations for Class 2 landfills. These modifications, though extensive in design and construction cost, are considered minor revisions and should not require a processing fee. Area 1 of ILF V, comprising approximately 20% of the ILF V footprint, was designed and submitted to TDEC prior to the implementation of current regulations. This initial area was constructed with a compacted clay liner and leachate collection system, and became operational in April 1994. The current regulations requiremore » landfills to have a composite liner with leachate collection system and closure cap. Modifications to upgrade Areas 2 and 3 of ILF V to meet the current TDEC requirements are included.« less

Seasonal carbon dioxide exchange between the regolith and atmosphere of Mars - Experimental and theoretical studies

NASA Technical Reports Server (NTRS)

Fanale, F. P.; Salvail, J. R.; Banerdt, W. B.; Saunders, R. S.; Johansen, L. A.

1982-01-01

CO2 penetration rate measurements have been made through basalt-clay soils under conditions simulating the penetration of the cap-induced seasonal CO2 pressure wave through the topmost regolith of Mars, and results suggest that existing theoretical models for the diffusion of a gas through a porous and highly adsorbing medium may be used to assess the importance of the Martian seasonal regolith-atmosphere CO2 exchange. The maximum effect of thermally driven exchange between the topmost seasonally (thermally) affected regolith and the atmosphere shows that, while this may be of greater importance than the isothermal exchange, the thermally driven exchange would be recognizable only if the pressure wave from CO2 exchanged at high latitudes did not propagate atmospherically faster than the rate at which the exchange itself occurred. This is an unreasonable assumption.

Precast, Prestressed Concrete Bent Caps : Volume 1, Preliminary Design Considerations and Experimental Test Program

DOT National Transportation Integrated Search

2018-04-01

Precast prestressed concrete bent caps may provide significant benefits by enabling accelerated construction of bridge substructures and improve longevity by reducing the propensity for cracking. The Texas Department of Transportation enables the use...

76 FR 23992 - Meeting To Review and Solicit Input on Tests for Inclusion in the Project 25 Compliance...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-29

... Solicit Input on Tests for Inclusion in the Project 25 Compliance Assessment Program AGENCY: National... inclusion in the P25 CAP. The following criteria are provided as a basis for comment: Does the conformance...' suitability for inclusion in the P25 CAP. The following criteria are provided as a basis for comment: For all...

An immunohistochemical and fluorescence in situ hybridization-based comparison between the Oracle HER2 Bond Immunohistochemical System, Dako HercepTest, and Vysis PathVysion HER2 FISH using both commercially validated and modified ASCO/CAP and United Kingdom HER2 IHC scoring guidelines.

PubMed

O'Grady, Anthony; Allen, David; Happerfield, Lisa; Johnson, Nicola; Provenzano, Elena; Pinder, Sarah E; Tee, Lilian; Gu, Mai; Kay, Elaine W

2010-12-01

Immunohistochemistry (IHC) is used as the frontline assay to determine HER2 status in invasive breast cancer patients. The aim of the study was to compare the performance of the Leica Oracle HER2 Bond IHC System (Oracle) with the current most readily accepted Dako HercepTest (HercepTest), using both commercially validated and modified ASCO/CAP and UK HER2 IHC scoring guidelines. A total of 445 breast cancer samples from 3 international clinical HER2 referral centers were stained with the 2 test systems and scored in a blinded fashion by experienced pathologists. The overall agreement between the 2 tests in a 3×3 (negative, equivocal and positive) analysis shows a concordance of 86.7% and 86.3%, respectively when analyzed using commercially validated and modified ASCO/CAP and UK HER2 IHC scoring guidelines. There is a good concordance between the Oracle and the HercepTest. The advantages of a complete fully automated test such as the Oracle include standardization of key analytical factors and improved turn around time. The implementation of the modified ASCO/CAP and UK HER2 IHC scoring guidelines has minimal effect on either assay interpretation, showing that Oracle can be used as a methodology for accurately determining HER2 IHC status in formalin fixed, paraffin-embedded breast cancer tissue.

Management of community-acquired pneumonia in adults: 2016 guideline update from the Dutch Working Party on Antibiotic Policy (SWAB) and Dutch Association of Chest Physicians (NVALT).

PubMed

Wiersinga, W J; Bonten, M J; Boersma, W G; Jonkers, R E; Aleva, R M; Kullberg, B J; Schouten, J A; Degener, J E; van de Garde, E M W; Verheij, T J; Sachs, A P E; Prins, J M

2018-01-01

The Dutch Working Party on Antibiotic Policy in collaboration with the Dutch Association of Chest Physicians, the Dutch Society for Intensive Care and the Dutch College of General Practitioners have updated their evidence-based guidelines on the diagnosis and treatment of community-acquired pneumonia (CAP) in adults who present to the hospital. This 2016 update focuses on new data on the aetiological and radiological diagnosis of CAP, severity classification methods, initial antibiotic treatment in patients with severe CAP and the role of adjunctive corticosteroids. Other parts overlap with the 2011 guideline. Apart from the Q fever outbreak in the Netherlands (2007-2010) no other shifts in the most common causative agents of CAP or in their resistance patterns were observed in the last five years. Low-dose CT scanning may ultimately replace the conventional chest X-ray; however, at present, there is insufficient evidence to advocate the use of CT scanning as the new standard in patients evaluated for CAP. A pneumococcal urine antigen test is now recommended for all patients presenting with severe CAP; a positive test result can help streamline therapy once clinical stability has been reached and no other pathogens have been detected. Coverage for atypical microorganisms is no longer recommended in empirical treatment of severe CAP in the non-intensive care setting. For these patients (with CURB-65 score >2 or Pneumonia Severity Index score of 5) empirical therapy with a 2nd/3rd generation cephalosporin is recommended, because of the relatively high incidence of Gram-negative bacteria, and to a lesser extent S. aureus. Corticosteroids are not recommended as adjunctive therapy for CAP.

Respirable dust and quartz exposure from three South African farms with sandy, sandy loam, and clay soils.

PubMed

Swanepoel, Andrew J; Kromhout, Hans; Jinnah, Zubair A; Portengen, Lützen; Renton, Kevin; Gardiner, Kerry; Rees, David

2011-07-01

To quantify personal time-weighted average respirable dust and quartz exposure on a sandy, a sandy loam, and a clay soil farm in the Free State and North West provinces of South Africa and to ascertain whether soil type is a determinant of exposure to respirable quartz. Three farms, located in the Free State and North West provinces of South Africa, had their soil type confirmed as sandy, sandy loam, and clay; and, from these, a total of 298 respirable dust and respirable quartz measurements were collected between July 2006-November 2009 during periods of major farming operations. Values below the limit of detection (LOD) (22 μg · m(-3)) were estimated using multiple 'imputation'. Non-parametric tests were used to compare quartz exposure from the three different soil types. Exposure to respirable quartz occurred on all three farms with the highest individual concentration measured on the sandy soil farm (626 μg · m(-3)). Fifty-seven, 59, and 81% of the measurements on the sandy soil, sandy loam soil, and clay soil farm, respectively, exceeded the American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 25 μg · m(-3). Twelve and 13% of respirable quartz concentrations exceeded 100 μg · m(-3) on the sandy soil and sandy loam soil farms, respectively, but none exceeded this level on the clay soil farm. The proportions of measurements >100 μg · m(-3) were not significantly different between the sandy and sandy loam soil farms ('prop.test'; P = 0.65), but both were significantly larger than for the clay soil farm ('prop.test'; P = 0.0001). The percentage of quartz in respirable dust was determined for all three farms using measurements > the limit of detection. Percentages ranged from 0.5 to 94.4% with no significant difference in the median quartz percentages across the three farms (Kruskal-Wallis test; P = 0.91). This study demonstrates that there is significant potential for over-exposure to respirable quartz in farming and even clay soil farming may pose a risk. Soil type may determine whether exposure is >100 μg · m(3), but the job type and the manner in which the task is performed (e.g. mechanical or manual) may be important determinants of exposure. Identifying quartz exposure determinants (e.g. type of job) and modifiers will be of value to focus implementation of controls of particular importance in developing countries.

Suitability of the methylene blue test for determination of cation exchange capacity of clay minerals related to ammonium acetate method

NASA Astrophysics Data System (ADS)

Milošević, Maja; Logar, Mihovil; Dojčinović, Biljana; Erić, Suzana

2015-04-01

Cation exchange capacity (CEC) represents one of the most important parameters of clay minerals which reflects their ability to exchange cations with liquid phases in near contact. Measurement of CEC is used for characterizing sample plasticity, adsorbing and swelling properties which later define their usage in industrial purposes. Several methods have been developed over the years for determination of layer charge, charge density, charge distribution, etc. and have been published in numerous papers (Czimerova et al., 2006; Yukselen and Kaya, 2008). The main goal of present study is comparison of suitability of more recent method - methylene blue test in regard to older method - ammonium acetate for determination of CEC. For this study, we selected one montmorillonite clay (Bogovina, Serbia) and two mainly kaolinite clays (Miličinica, Serbia). Chemicals used for CEC determinations were solution of methylene blue (MB)(14*10-6M/ml) and ammonium acetate (AA) solution (1M). The obtained results are showing generally lower values in case of MB method. The main difference is due to molecular aggregation of MB on the clay surface. AA method is highly sensitive to the presence of CaO. Release of Ca ion from the sample into the solution can limit the saturation of exchange sites by the ammonium ion. This is clearly visible in case of montmorillonite clay. Fe2+ and Mg ions are difficult to move by the ammonium ion because of their ion radius, but in case of MB molecule there is no such restriction in removing them from the exchange sites. MB solution, even in a low concentration (2*10-6M/ml), is showing preferable results in moving the ions from their positions which is already visible after adding a small quantity of solution (25cm3). Both MB-titration and MB-spot test yield similar results and are much simpler methods than AA and they also give other information such as specific surface area (external and internal) whereas AA method only provides information about cations in exchangeable positions. Both methods, methylene blue test and ammonium acetate method, have advantages and disadvantages and differ in their requirements for the sample preparations but in general method selection is depending on the specific application of the given sample. References: - Yukselen, Y. and Kaya, A., Engineering Geology 102 (2008) 38-45 - Czimerova, A., Bujdak, J. and Dohrmann, R., Applied Clay Science 34 (2006) 2-13

Petrophysical analysis of geophysical logs of the National Drilling Company-U.S. Geological Survey ground-water research project for Abu Dhabi Emirate, United Arab Emirates

USGS Publications Warehouse

Jorgensen, Donald G.; Petricola, Mario

1994-01-01

A program of borehole-geophysical logging was implemented to supply geologic and geohydrologic information for a regional ground-water investigation of Abu Dhabi Emirate. Analysis of geophysical logs was essential to provide information on geohydrologic properties because drill cuttings were not always adequate to define lithologic boundaries. The standard suite of logs obtained at most project test holes consisted of caliper, spontaneous potential, gamma ray, dual induction, microresistivity, compensated neutron, compensated density, and compensated sonic. Ophiolitic detritus from the nearby Oman Mountains has unusual petrophysical properties that complicated the interpretation of geophysical logs. The density of coarse ophiolitic detritus is typically greater than 3.0 grams per cubic centimeter, porosity values are large, often exceeding 45 percent, and the clay fraction included unusual clays, such as lizardite. Neither the spontaneous-potential log nor the natural gamma-ray log were useable clay indicators. Because intrinsic permeability is a function of clay content, additional research in determining clay content was critical. A research program of geophysical logging was conducted to determine the petrophysical properties of the shallow subsurface formations. The logging included spectral-gamma and thermal-decay-time logs. These logs, along with the standard geophysical logs, were correlated to mineralogy and whole-rock chemistry as determined from sidewall cores. Thus, interpretation of lithology and fluids was accomplished. Permeability and specific yield were calculated from geophysical-log data and correlated to results from an aquifer test. On the basis of results from the research logging, a method of lithologic and water-resistivity interpretation was developed for the test holes at which the standard suite of logs were obtained. In addition, a computer program was developed to assist in the analysis of log data. Geohydrologic properties were estimated, including volume of clay matrix, volume of matrix other than clay, density of matrix other than clay, density of matrix, intrinsic permeability, specific yield, and specific storage. Geophysical logs were used to (1) determine lithology, (2) correlate lithologic and permeable zones, (3) calibrate seismic reprocessing, (4) calibrate transient-electromagnetic surveys, and (5) calibrate uphole-survey interpretations. Logs were used at the drill site to (1) determine permeability zones, (2) determine dissolved-solids content, which is a function of water resistivity, and (3) design wells accordingly. Data and properties derived from logs were used to determine transmissivity and specific yield of aquifer materials.

Impact of Vial Capping on Residual Seal Force and Container Closure Integrity.

PubMed

Mathaes, Roman; Mahler, Hanns-Christian; Roggo, Yves; Ovadia, Robert; Lam, Philippe; Stauch, Oliver; Vogt, Martin; Roehl, Holger; Huwyler, Joerg; Mohl, Silke; Streubel, Alexander

2016-01-01

The vial capping process is a critical unit operation during drug product manufacturing, as it could possibly generate cosmetic defects or even affect container closure integrity. Yet there is significant variability in capping equipment and processes, and their relation to potential defects or container closure integrity has not been thoroughly studied. In this study we applied several methods-residual seal force tester, a self-developed system of a piezo force sensor measurement, and computed tomography-to characterize different container closure system combinations that had been sealed using different capping process parameter settings. Additionally, container closure integrity of these samples was measured using helium leakage (physical container closure integrity) and compared to characterization data. The different capping equipment settings lead to residual seal force values from 7 to 115 N. High residual seal force values were achieved with high capping pre-compression force and a short distance between the capping plate and plunge. The choice of container closure system influenced the obtained residual seal force values. The residual seal force tester and piezoelectric measurements showed similar trends. All vials passed physical container closure integrity testing, and no stopper rupture was seen with any of the settings applied, suggesting that container closure integrity was warranted for the studied container closure system with the chosen capping setting ranges. The vial capping process is a critical unit operation during drug product manufacturing, as it could possibly generate cosmetic defects or even affect container closure integrity. Yet there is significant variability in capping equipment and processes, and their relation to potential defects or container closure integrity has not been thoroughly studied. In this study we applied several methods-residual seal force tester, a self-developed system of a piezo force sensor measurement, and computed tomography-to characterize different container closure system combinations that had been sealed using different capping process parameter settings. The residual seal force tester can analyze a variety of different container closure systems independent of the capping equipment. An adequate and safe residual seal force range for each container closure system configuration can be established with the residual seal force tester and additional methods like computed tomography scans and leak testing. In the residual seal force range studied, the physical container closure integrity of the container closure system was warranted. © PDA, Inc. 2016.

Towards a numerical run-out model for quick-clay slides

NASA Astrophysics Data System (ADS)

Issler, Dieter; L'Heureux, Jean-Sébastien; Cepeda, José M.; Luna, Byron Quan; Gebreslassie, Tesfahunegn A.

2015-04-01

Highly sensitive glacio-marine clays occur in many relatively low-lying areas near the coasts of eastern Canada, Scandinavia and northern Russia. If the load exceeds the yield stress of these clays, they quickly liquefy, with a reduction of the yield strength and the viscosity by several orders of magnitude. Leaching, fluvial erosion, earthquakes and man-made overloads, by themselves or combined, are the most frequent triggers of quick-clay slides, which are hard to predict and can attain catastrophic dimensions. The present contribution reports on two preparatory studies that were conducted with a view to creating a run-out model tailored to the characteristics of quick-clay slides. One study analyzed the connections between the morphological and geotechnical properties of more than 30 well-documented Norwegian quick-clay slides and their run-out behavior. The laboratory experiments by Locat and Demers (1988) suggest that the behavior of quick clays can be reasonably described by universal relations involving the liquidity index, plastic index, remolding energy, salinity and sensitivity. However, these tests should be repeated with Norwegian clays and analyzed in terms of a (shear-thinning) Herschel-Bulkley fluid rather than a Bingham fluid because the shear stress appears to grow in a sub-linear fashion with the shear rate. Further study is required to understand the discrepancy between the material parameters obtained in laboratory tests of material from observed slides and in back-calculations of the same slides with the simple model by Edgers & Karlsrud (1982). The second study assessed the capability of existing numerical flow models to capture the most important aspects of quick-clay slides by back-calculating three different, well documented events in Norway: Rissa (1978), Finneidfjord (1996) and Byneset (2012). The numerical codes were (i) BING, a quasi-two-dimensional visco-plastic model, (ii) DAN3D (2009 version), and (iii) MassMov2D. The latter two are quasi-three-dimensional codes with a choice of bed-friction laws. The findings of the simulations point strongly towards the need for a different modeling approach that incorporates the essential physical features of quick-clay slides. The major requirement is a realistic description of remolding. A two-layer model is needed to describe the non-sensitive topsoil that often is passively advected by the slide. In many cases, the topography is rather complex so that 3D or quasi-3D (depth-averaged) models are required for realistic modeling of flow heights and velocities. Finally, since many Norwegian quick-clay slides run-out in a fjord (and may generate a tsunami), it is also desirable to explicitly account for buoyancy and hydrodynamic drag.

Numerical analysis of dense narrow backfills for increasing lateral passive resistance.

DOT National Transportation Integrated Search

2010-08-01

Previously, full-scale lateral load tests conducted on pile caps with different aspect ratios showed that placement : of a narrow, dense backfill zone against the cap could substantially increase the passive resistance. The objective : of this study ...

ASR/DEF-damaged bent caps : shear tests and field implications.

DOT National Transportation Integrated Search

2009-08-01

Over the last decade, a number of reinforced concrete bent caps within Houston, Texas have exhibited premature concrete damage (cracking, spalling and a loss of material : strength) due to alkali-silica reaction (ASR) and/or delayed ettringite format...

Sorption-desorption of imidacloprid onto a lacustrine Egyptian soil and its clay and humic acid fractions.

PubMed

Kandil, Mahrous M; El-Aswad, Ahmed F; Koskinen, William C

2015-01-01

Sorption-desorption of the insecticide imidacloprid 1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine onto a lacustrine sandy clay loam Egyptian soil and its clay and humic acid (HA) fractions was investigated in 24-h batch equilibrium experiments. Imidacloprid (IMDA) sorption-desorption isotherms onto the three sorbents were found to belong to a non-linear L-type and were best described by the Freundlich model. The value of the IMDA adsorption distribution coefficient, Kd(ads), varied according to its initial concentration and was ranged 40-84 for HA, 14-58 for clay and 1.85-4.15 for bulk soil. Freundlich sorption coefficient, Kf(ads), values were 63.0, 39.7 and 4.0 for HA, clay and bulk soil, respectively. The normalized soil Koc value for imidacloprid sorption was ∼800 indicating its slight mobility in soils. Nonlinear sorption isotherms were indicated by 1/n(ads) values <1 for all sorbents. Values of the hysteresis index (H) were <1, indicating the irreversibility of imidacloprid sorption process with all tested sorbents. Gibbs free energy (ΔG) values indicated a spontaneous and physicosorption process for IMDA and a more favorable sorption to HA than clay and soil. In conclusion, although the humic acid fraction showed the highest capacity and affinity for imidacloprid sorption, the clay fraction contributed to approximately 95% of soil-sorbed insecticide. Clay and humic acid fractions were found to be the major two factors controlling IMDA sorption in soils. The slight mobility of IMDA in soils and the hysteresis phenomenon associated with the irreversibility of its sorption onto, mainly, clay and organic matter of soils make its leachability unlikely to occur.

A smart cap for olive oil rancidity detection using optochemical sensors

NASA Astrophysics Data System (ADS)

Mignani, A. G.; Ciaccheri, L.; Mencaglia, A. A.; Paolesse, R.; Mastroianni, M.; Monti, D.; Buonocore, G.; Del Nobile, A.; Mentana, A.; Grimaldi, M. F.

2007-09-01

The design and experimental setup of a smart cap are presented. It is capable of sniffing the vapors of extra virgin olive oil, thus alerting the consumer or the retailer of any rancid flavor. The cap is made of an array of metalloporphyrin-based optochemical sensors, the colors of which are modulated by the concentration of aldehydes, the main responsible for rancid off-flavors. A micro-optic device, implemented to simulate a cap prototype, is presented. The spectral response of the chromophore-array is processed by means of multivariate data analysis so as to achieve an artificial olfactory perception of oil aroma and, consequently, an indication of oil ageing and rancidity. In practice, the cap prototype proved to be a device for non-destructive testing of bottled oil quality.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maines, Warren Russell; Kittell, David E.; Hobbs, Michael L.

In this work, we combined the miniature cylinder expansion test (Mini-Cylex), with the Disk Acceleration Test (DAX) using Type K copper, Picatinny Liquid Explosive, and photonic Doppler velocimetry. We estimated the CJ state using plate reverberation methods at the test cap. We extracted velocities at 2, 7, and 10 volume expansions to fit Jones-Wilkins-Lee Equation of State and estimated Gurney velocity at the tube wall. The test also provides an additional method to estimate reaction products Hugoniot through knowledge of the copper test cap. Our experiments and simulations are within expected uncertainty. Lastly, the test and the analysis effectively reducemore » costs while keeping or increasing fidelity.« less

Myofibril growth during cardiac hypertrophy is regulated through dual phosphorylation and acetylation of the actin capping protein CapZ

PubMed Central

Lin, Ying-Hsi; Warren, Chad M.; Li, Jieli; McKinsey, Timothy A.; Russell, Brenda

2016-01-01

The mechanotransduction signaling pathways initiated in heart muscle by increased mechanical loading are known to lead to long-term transcriptional changes and hypertrophy, but the rapid events for adaptation at the sarcomeric level are not fully understood. The goal of this study was to test the hypothesis that actin filament assembly during cardiomyocyte growth is regulated by post-translational modifications (PTMs) of CapZβ1. In rapidly hypertrophying neonatal rat ventricular myocytes (NRVMs) stimulated by phenylephrine (PE), two-dimensional gel electrophoresis (2DGE) of CapZβ1 revealed a shift toward more negative charge. Consistent with this, mass spectrometry identified CapZβ1 phosphorylation on serine-204 and acetylation on lysine-199, two residues which are near the actin binding surface of CapZβ1. Ectopic expression of dominant negative PKCε (dnPKCε) in NRVMs blunted the PE-induced increase in CapZ dynamics, as evidenced by the kinetic constant (Kfrap) of fluorescence recovery after photobleaching (FRAP), and concomitantly reduced phosphorylation and acetylation of CapZβ1. Furthermore, inhibition of class I histone deacetylases (HDACs) increased lysine-199 acetylation on CapZβ1, which increased Kfrap of CapZ and stimulated actin dynamics. Finally, we show that PE treatment of NRVMs results in decreased binding of HDAC3 to myofibrils, suggesting a signal-dependent mechanism for the regulation of sarcomere-associated CapZβ1 acetylation. Taken together, this dual regulation through phosphorylation and acetylation of CapZβ1 provides a novel model for the regulation of myofibril growth during cardiac hypertrophy. PMID:27185186

Ball clay and bentonite deposits of the central and western Gulf of Mexico Coastal Plain, United States

USGS Publications Warehouse

Hosterman, John W.

1984-01-01

The Gulf of Mexico Coastal Plain produces approximately 85 percent of the ball clay used in the United States. The best commercial-grade clay deposits are composed of poorly crystalline kaolinite and small amounts of Md illite and (or) smectite. Sand and silt and iron oxide minerals are virtually absent, but quartz is present in the clay-size fraction. The best grade ball clays are found as lenses limited to the Wilcox Group (Paleocene and lower Eocene) and Claiborne Group (middle Eocene). Reserves of ball clay are sufficient for the present, but because of the lenticular nature of the clay bodies, close-spaced drilling, detailed sampling, mineralogic analyses, and ceramic testing are needed to prove future reserves.Approximately 11 percent of the total bentonite produced in the United States comes from the Gulf Coast region. The commercial-grade bentonites are composed primarily of smectite with little or no Md illite and kaolinite. The nonclay impurities are quartz, feldspar, muscovite, biotite, calcite, dolomite, gypsum, and heulandite. Commercial bentonites occur in the Upper Cretaceous formations in Alabama and Mississippi, in Paleocene formations in Mississippi and Tennessee, and in Eocene and Miocene formations in Texas. The demand for low-swelling bentonite of the Gulf Coastal Plain has not increased along with the demand for swelling bentonite; therefore the reserves are adequate.

Zr-doped TiO2 supported on delaminated clay materials for solar photocatalytic treatment of emerging pollutants.

PubMed

Belver, C; Bedia, J; Rodriguez, J J

2017-01-15

Solar light-active Zr-doped TiO 2 nanoparticles were successfully immobilized on delaminated clay materials by a one-step sol-gel route. Fixing the amount of TiO 2 at 65wt.%, this work studies the influence of Zr loading (up to 2%) on the photocatalytic activity of the resulting Zr-doped TiO 2 /clay materials. The structural characterization demonstrates that all samples were formed by a delaminated clay with nanostructured anatase assembled on its surface. The Zr dopant was successfully incorporated into the anatase lattice, resulting in a slight deformation of the anatase crystal and the reduction of the band gap. These materials exhibit high surface area with a disordered mesoporous structure formed by TiO 2 particles (15-20nm) supported on a delaminated clay. They were tested in the solar photodegradation of antipyrine, usually used as an analgesic drug and selected as an example of emerging pollutant. High degradation rates have been obtained at low antipyrine concentrations and high solar irradiation intensities with the Zr-doped TiO 2 /clay catalyst, more effective than the undoped one. This work demonstrates the potential application of the synthesis method for preparing novel and efficient solar-light photocatalysts based on metal-doped anatase and a delaminated clay. Copyright © 2016 Elsevier B.V. All rights reserved.

How do changes in bulk soil organic carbon content affect carbon concentrations in individual soil particle fractions?

PubMed Central

Yang, X. M.; Drury, C. F.; Reynolds, W. D.; Yang, J. Y.

2016-01-01

We test the common assumption that organic carbon (OC) storage occurs on sand-sized soil particles only after the OC storage capacity on silt- and clay-sized particles is saturated. Soil samples from a Brookston clay loam in Southwestern Ontario were analysed for the OC concentrations in bulk soil, and on the clay (<2 μm), silt (2–53 μm) and sand (53–2000 μm) particle size fractions. The OC concentrations in bulk soil ranged from 4.7 to 70.8 g C kg−1 soil. The OC concentrations on all three particle size fractions were significantly related to the OC concentration of bulk soil. However, OC concentration increased slowly toward an apparent maximum on silt and clay, but this maximum was far greater than the maximum predicted by established C sequestration models. In addition, significant increases in OC associated with sand occurred when the bulk soil OC concentration exceeded 30 g C kg−1, but this increase occurred when the OC concentration on silt + clay was still far below the predicted storage capacity for silt and clay fractions. Since the OC concentrations in all fractions of Brookston clay loam soil continued to increase with increasing C (bulk soil OC content) input, we concluded that the concept of OC storage capacity requires further investigation. PMID:27251365

How do changes in bulk soil organic carbon content affect carbon concentrations in individual soil particle fractions?

NASA Astrophysics Data System (ADS)

Yang, X. M.; Drury, C. F.; Reynolds, W. D.; Yang, J. Y.

2016-06-01

We test the common assumption that organic carbon (OC) storage occurs on sand-sized soil particles only after the OC storage capacity on silt- and clay-sized particles is saturated. Soil samples from a Brookston clay loam in Southwestern Ontario were analysed for the OC concentrations in bulk soil, and on the clay (<2 μm), silt (2-53 μm) and sand (53-2000 μm) particle size fractions. The OC concentrations in bulk soil ranged from 4.7 to 70.8 g C kg-1 soil. The OC concentrations on all three particle size fractions were significantly related to the OC concentration of bulk soil. However, OC concentration increased slowly toward an apparent maximum on silt and clay, but this maximum was far greater than the maximum predicted by established C sequestration models. In addition, significant increases in OC associated with sand occurred when the bulk soil OC concentration exceeded 30 g C kg-1, but this increase occurred when the OC concentration on silt + clay was still far below the predicted storage capacity for silt and clay fractions. Since the OC concentrations in all fractions of Brookston clay loam soil continued to increase with increasing C (bulk soil OC content) input, we concluded that the concept of OC storage capacity requires further investigation.

Centrifugal Tensioned Metastable Fluid Detectors for Trace Radiation Sources: Experimental Verification and Military Employment

DTIC Science & Technology

2016-06-01

used in both CTMFD and Beckman LS 6500 Scintillation System. Actinide   Mass  of  Nalgene  (g)  Mass  of  Cap (g)  Mass  of  Nalgene,  Cap, 50 mL...both CTMFD and Beckman LS 6500 Scintillation System. Actinide   Mass  of  Nalgene  and Cap  (g)  Mass  of  Nalgene, Cap,  50 mL Acetone  (g)  Mass  of...testing comparing the CTMFD’s capabilities of actinide spectroscopy and neutron detection against other detection systems with similar capabilities. The

Development of a prototype commonality analysis tool for use in space programs

NASA Technical Reports Server (NTRS)

Yeager, Dorian P.

1988-01-01

A software tool to aid in performing commonality analyses, called Commonality Analysis Problem Solver (CAPS), was designed, and a prototype version (CAPS 1.0) was implemented and tested. The CAPS 1.0 runs in an MS-DOS or IBM PC-DOS environment. The CAPS is designed around a simple input language which provides a natural syntax for the description of feasibility constraints. It provides its users with the ability to load a database representing a set of design items, describe the feasibility constraints on items in that database, and do a comprehensive cost analysis to find the most economical substitution pattern.

The Ability of an Aftermarket Helmet Add-On Device to Reduce Impact-Force Accelerations During Drop Tests.

PubMed

Breedlove, Katherine M; Breedlove, Evan; Nauman, Eric; Bowman, Thomas G; Lininger, Monica R

2017-09-01

  The Guardian Cap provides a soft covering intended to mitigate energy transfer to the head during football contact. Yet how well it attenuates impacts remains unknown.   To evaluate the changes in the Gadd Severity Index (GSI) and linear acceleration during drop tests on helmeted headforms with or without Guardian Caps.   Crossover study.   Laboratory.   Nine new football helmets sent directly from the manufacturer.   We dropped the helmets at 3 velocities on 6 helmet locations (front, side, right front boss, top, rear right boss, and rear) as prescribed by the National Operating Committee on Standards for Athletic Equipment. Helmets were tested with facemasks in place but no Guardian Cap and then retested with the facemasks in place and the Guardian Cap affixed.   The GSI scores and linear accelerations measured in g forces.   For the GSI, we found a significant interaction among drop location, Guardian Cap presence, and helmet brand at the high velocity (F 10,50 = 3.01, P = .005) but not at the low (F 3.23,16.15 = 0.84, P = .50) or medium (F 10,50 = 1.29, P = .26) velocities. Similarly for linear accelerations, we found a significant interaction among drop location, Guardian Cap presence, and helmet brand at the high velocity (F 10,50 = 3.01, P = .002, ω 2 = 0.05) but not at the low (F 10,50 = 0.49, P = .89, ω 2 < 0.01, 1-β = 0.16) or medium (F 5.20,26.01 = 2.43, P = .06, ω 2 < 0.01, 1-β = 0.68) velocities.   The Guardian Cap failed to significantly improve the helmets' ability to mitigate impact forces at most locations. Limited evidence indicates how a reduction in GSI would provide clinically relevant benefits beyond reducing the risk of skull fracture or a similar catastrophic event.

MEASUREMENT OF CONTROLLED ATTENUATION PARAMETER: A SURROGATE MARKER OF HEPATIC STEATOSIS IN PATIENTS OF NONALCOHOLIC FATTY LIVER DISEASE ON LIFESTYLE MODIFICATION - A PROSPECTIVE FOLLOW-UP STUDY.

PubMed

Paul, Jayanta; Venugopal, Raj Vigna; Peter, Lorance; Shetty, Kula Naresh Kumar; Shetti, Mohit P

2018-01-01

Liver biopsy is a gold standard method for hepatic steatosis assessment. However, liver biopsy is an invasive and painful procedure and can cause severe complications therefore it cannot be frequently used in case of follow-up of patients. Non-invasive assessment of steatosis and fibrosis is of growing relevance in non-alcoholic fatty liver disease (NAFLD). To evaluate hepatic steatosis, transient elastography with controlled attenuation parameter (CAP) measurement is an option now days. Aim of this study is to evaluate role of measurement of controlled attenuation parameter, a surrogate marker of hepatic steatosis in patients of nonalcoholic fatty liver disease on lifestyle modification. In this study, initially 37 participants were included who were followed up after 6 months with transient elastography, blood biochemical tests and anthropometric measurements. The results were analyzed by Multivariate linear regression analysis and paired samples t-test (Dependent t-test) with 95% confidence interval. Correlation is calculated by Pearson correlation coefficients. Mean CAP value for assessing hepatic steatosis during 1st consultation (278.57±49.13 dB/m) was significantly improved (P=0.03) after 6 months of lifestyle modification (252.91±62.02 dB/m). Only fasting blood sugar (P=0.008), weight (P=0.000), body mass index (BMI) (P=0.000) showed significant positive correlation with CAP. Only BMI (P=0.034) and weight (P=0.035) were the independent predictor of CAP value in NAFLD patients. Lifestyle modification improves the hepatic steatosis, and CAP can be used to detect the improvement of hepatic steatosis during follow-up in patients with NAFLD on lifestyle modification. There is no relation between CAP and Fibroscan score in NAFLD patients. Only BMI and weight can predict CAP value independently.

Determining the spatial variability of personal sampler inlet locations.

PubMed

Vinson, Robert; Volkwein, Jon; McWilliams, Linda

2007-09-01

This article examines the spatial variability of dust concentrations within a coal miner's breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value < .0001). This finding is important because the lapel has always been the sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Capsaicin Supplementation Reduces Physical Fatigue and Improves Exercise Performance in Mice

PubMed Central

Hsu, Yi-Ju; Huang, Wen-Ching; Chiu, Chien-Chao; Liu, Yan-Lin; Chiu, Wan-Chun; Chiu, Chun-Hui; Chiu, Yen-Shuo; Huang, Chi-Chang

2016-01-01

Chili pepper is used as a food, seasoning and has been revered for its medicinal and health claims. It is very popular and is the most common spice worldwide. Capsaicin (CAP) is a major pungent and bioactive phytochemical in chili peppers. CAP has been shown to improve mitochondrial biogenesis and adenosine triphosphate (ATP) production. However, there is limited evidence around the effects of CAP on physical fatigue and exercise performance. The purpose of this study was to evaluate the potential beneficial effects of CAP on anti-fatigue and ergogenic functions following physiological challenge. Female Institute of Cancer Research (ICR) mice from four groups (n = 8 per group) were orally administered CAP for 4 weeks at 0, 205, 410, and 1025 mg/kg/day, which were respectively designated the vehicle, CAP-1X, CAP-2X, and CAP-5X groups. The anti-fatigue activity and exercise performance was evaluated using forelimb grip strength, exhaustive swimming time, and levels of serum lactate, ammonia, glucose, BUN (blood urea nitrogen) and creatine kinase (CK) after a 15-min swimming exercise. The grip strength and exhaustive swimming time of the CAP-5X group were significantly higher than other groups. CAP supplementation dose-dependently reduced serum lactate, ammonia, BUN and CK levels, and increased glucose concentration after the 15-min swimming test. In addition, CAP also increased hepatic glycogen content, an important energy source for exercise. The possible mechanism was relevant to energy homeostasis and the physiological modulations by CAP supplementation. Therefore, our results suggest that CAP supplementation may have a wide spectrum of bioactivities for promoting health, performance improvement and fatigue amelioration. PMID:27775591

Capsaicin Supplementation Reduces Physical Fatigue and Improves Exercise Performance in Mice.

PubMed

Hsu, Yi-Ju; Huang, Wen-Ching; Chiu, Chien-Chao; Liu, Yan-Lin; Chiu, Wan-Chun; Chiu, Chun-Hui; Chiu, Yen-Shuo; Huang, Chi-Chang

2016-10-20

Chili pepper is used as a food, seasoning and has been revered for its medicinal and health claims. It is very popular and is the most common spice worldwide. Capsaicin (CAP) is a major pungent and bioactive phytochemical in chili peppers. CAP has been shown to improve mitochondrial biogenesis and adenosine triphosphate (ATP) production. However, there is limited evidence around the effects of CAP on physical fatigue and exercise performance. The purpose of this study was to evaluate the potential beneficial effects of CAP on anti-fatigue and ergogenic functions following physiological challenge. Female Institute of Cancer Research (ICR) mice from four groups ( n = 8 per group) were orally administered CAP for 4 weeks at 0, 205, 410, and 1025 mg/kg/day, which were respectively designated the vehicle, CAP-1X, CAP-2X, and CAP-5X groups. The anti-fatigue activity and exercise performance was evaluated using forelimb grip strength, exhaustive swimming time, and levels of serum lactate, ammonia, glucose, BUN (blood urea nitrogen) and creatine kinase (CK) after a 15-min swimming exercise. The grip strength and exhaustive swimming time of the CAP-5X group were significantly higher than other groups. CAP supplementation dose-dependently reduced serum lactate, ammonia, BUN and CK levels, and increased glucose concentration after the 15-min swimming test. In addition, CAP also increased hepatic glycogen content, an important energy source for exercise. The possible mechanism was relevant to energy homeostasis and the physiological modulations by CAP supplementation. Therefore, our results suggest that CAP supplementation may have a wide spectrum of bioactivities for promoting health, performance improvement and fatigue amelioration.

Production of porous Calcium Phosphate (CaP) ceramics with aligned pores using ceramic/camphene-based co-extrusion.

PubMed

Choi, Won-Young; Kim, Hyoun-Ee; Moon, Young-Wook; Shin, Kwan-Ha; Koh, Young-Hag

2015-01-01

Calcium phosphate (CaP) ceramics are one of the most valuable biomaterials for uses as the bone scaffold owing to their outstanding biocompatability, bioactivity, and biodegradation nature. In particular, these materials with an open porous structure can stimulate bone ingrowth into their 3-dimensionally interconnected pores. However, the creation of pores in bulk materials would inevitably cause a severe reduction in mechanical properties. Thus, it is a challenge to explore new ways of improving the mechanical properties of porous CaP scaffolds without scarifying their high porosity. Porous CaP ceramic scaffolds with aligned pores were successfully produced using ceramic/camphene-based co-extrusion. This aligned porous structure allowed for the achievement of high compressive strength when tested parallel to the direction of aligned pores. In addition, the overall porosity and mechanical properties of the aligned porous CaP ceramic scaffolds could be tailored simply by adjusting the initial CaP content in the CaP/camphene slurry. The porous CaP scaffolds showed excellent in vitro biocompatibility, suggesting their potential as the bone scaffold. Aligned porous CaP ceramic scaffolds with considerably enhanced mechanical properties and tailorable porosity would find very useful applications as the bone scaffold.

Phytoextraction of Pb and Cu contaminated soil with maize and microencapsulated EDTA.

PubMed

Xie, Zhiyi; Wu, Longhua; Chen, Nengchang; Liu, Chengshuai; Zheng, Yuji; Xu, Shengguang; Li, Fangbai; Xu, Yanling

2012-09-01

Chelate-assisted phytoextraction using agricultural crops has been widely investigated as a remediation technique for soils contaminated with low mobility potentially toxic elements. Here, we report the use of a controlled-release microencapsulated EDTA (Cap-EDTA) by emulsion solvent evaporation to phytoremediate soil contaminated with Pb and Cu. Incubation experiments were carried out to assess the effect of Cap- and non-microencapsulated EDTA (Ncap-EDTA) on the mobility of soil metals. Results showed EDTA effectively increased the mobility of Pb and Cu in the soil solution and Cap-EDTA application provided lower and more constant water-soluble concentrations of Pb and Cu in comparison with. Phytotoxicity may be alleviated and plant uptake of Pb and Cu may be increased after the incorporation of Cap-EDTA. In addition phytoextraction efficiencies of maize after Cap- and Ncap-EDTA application were tested in a pot experiment. Maize shoot concentrations of Pb and Cu were lower with Cap-EDTA application than with Ncap-EDTA. However, shoot dry weight was significantly higher with Cap-EDTA application. Consequently, the Pb and Cu phytoextraction potential of maize significantly increased with Cap-EDTA application compared with the control and Ncap-EDTA application.

Results of Laboratory Tests of the Filtration Characteristics of Clay-Cement Concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sol’skii, S. V., E-mail: solskiysv@vniig.ru; Lopatina, M. G., E-mail: LoptainaMG@vniig.ru; Legina, E. E.

Laboratory studies of the filtration characteristics of clay-cement concrete materials for constructing filtering diaphragms of earth dams by the method of secant piles are reported. Areas for further study aimed at improving the quality of construction, increasing operational safety, and developing a standards base for the design, construction, and operation of these systems are discussed.

Automated method for determining Instron Residual Seal Force of glass vial/rubber closure systems. Part II. 13 mm vials.

PubMed

Ludwig, J D; Davis, C W

1995-01-01

Instron Residual Seal Force (IRSF) of 13 mm glass vial/rubber closure systems was determined using an Instron 4501 Materials Testing System and computerized data analysis. A series of three cap anvils varying in shape and dimensions were machined to optimize cap anvil performance. Cap anvils with spherical top surfaces and narrow internal dimensions produced uniform stress-deformation curves from which precise IRSF values were derived.

Potential prebiotic properties of cashew apple (Anacardium occidentale L.) agro-industrial byproduct on Lactobacillus species.

PubMed

Duarte, Francisca Nayara Dantas; Rodrigues, Jéssica Bezerra; da Costa Lima, Maiara; Lima, Marcos Dos Santos; Pacheco, Maria Teresa Bertoldo; Pintado, Maria Manuela Estevez; de Souza Aquino, Jailane; de Souza, Evandro Leite

2017-08-01

The prebiotic effects of a cashew apple (Anacardium occidentale L.) agro-industrial byproduct powder (CAP) on different potentially probiotic Lactobacillus strains, namely Lactobacillus acidophilus LA-05, Lactobacillus casei L-26 and Lactobacillus paracasei L-10, were assessed using in vitro experimental models. Accordingly, the growth of the Lactobacillus strains when cultivated in a broth containing CAP (20 or 30 g L -1 ), glucose (20 g L -1 ) or fructooligosaccharides (FOS) (20 g L -1 ) was monitored over 48 h; the prebiotic activity scores of CAP were determined; and the changes in pH values, production of organic acids and consumption of sugars in growth media were verified. During the 48-h cultivation, similar viable cell counts were observed for the Lactobacillus strains grown in the different media tested. The CAP presented positive prebiotic activity scores toward all the tested Lactobacillus strains, indicating a desirable selective fermentable activity relative to enteric organisms. The cultivation of the Lactobacillus strains in broth containing glucose, FOS or CAP resulted in high viable cell counts, a decreased pH, the production of organic acids and the consumption of sugars over time, revealing intense bacterial metabolic activity. The CAP exerts potential prebiotic effects on different potentially probiotic Lactobacillus strains and should be an added-value ingredient for the food industry. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Effects of twelve weeks of capsaicinoid supplementation on body composition, appetite and self-reported caloric intake in overweight individuals.

PubMed

Urbina, Stacie L; Roberts, Michael D; Kephart, Wesley C; Villa, Katelyn B; Santos, Emily N; Olivencia, Alyssa M; Bennett, Haley M; Lara, Marissa D; Foster, Cliffa A; Purpura, Martin; Jäger, Ralf; Taylor, Lem W; Wilborn, Colin D

2017-06-01

We examined if 12 weeks of capsaicinoid (CAP) supplementation affected appetite, body composition and metabolic health markers. Seventy seven healthy male and female volunteers (30 ± 1 y, 171.2 ± 9.8 cm, 81.0 ± 2.2 kg, 27.5 ± 0.6 kg/m 2 ) were randomly assigned to ingest either low-dose CAP (2 mg/d; L-CAP, n = 27), high-dose CAP (4 mg/d; H-CAP, n = 22) from Capsimax or placebo (corn starch; PLA, n = 28) for 12 weeks. At baseline (0 WK), 6 weeks (6 WK) and 12 weeks (12 WK) waist: hip ratio, body composition via dual energy x-ray absorptiometry (DEXA, 0 WK and 12 WK only), self-reported Calorie intakes, appetite levels via Council on Nutrition Appetite Questionnaire (CNAQ) and serum metabolic health markers (0 WK and 12 WK only) were analyzed. Moreover, an oral glucose tolerance test (OGTT) was administered at 0 WK and 12 WK, and serum glucose and insulin responses were examined 30-120 min post test-drink consumption. Waist: hip ratio significantly decreased in L-CAP from 0 WK to 6 WK (p < 0.05), although supplementation did not significantly affect body composition. H-CAP consumed less kcal/d compared to PLA at 12 WK (difference = 257 kcal/d, p < 0.05) and L-CAP participants at 12 WK (difference = 247, p < 0.05). Twenty-three percent (9/39) of the originally-enrolled H-CAP participants reported GI distress, although no participants in the L-CAP group reported such adverse events. Interestingly, H-CAP participants presented significant increases in serum insulin as well as significant decreases in serum HDL cholesterol levels from WK0 to WK12. However, supplementation did not affect the insulin response to the administered OGTT and/or other indices of insulin sensitivity. These data suggest that H-CAP supplementation reduces self-reported energy intake after 12 weeks of supplementation, and L-CAP supplementation also reduces waist: hip ratio. Longer-term effects of capsaicinoid supplementation on basal insulin and cholesterol levels warrant further investigation. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Predictive values of semi-quantitative procalcitonin test and common biomarkers for the clinical outcomes of community-acquired pneumonia.

PubMed

Ugajin, Motoi; Yamaki, Kenichi; Hirasawa, Natsuko; Yagi, Takeo

2014-04-01

The semi-quantitative serum procalcitonin test (Brahms PCT-Q) is available conveniently in clinical practice. However, there are few data on the relationship between results for this semi-quantitative procalcitonin test and clinical outcomes of community-acquired pneumonia (CAP). We investigated the usefulness of this procalcitonin test for predicting the clinical outcomes of CAP in comparison with severity scoring systems and the blood urea nitrogen/serum albumin (B/A) ratio, which has been reported to be a simple but reliable prognostic indicator in our prior CAP study. This retrospective study included data from subjects who were hospitalized for CAP from August 2010 through October 2012 and who were administered the semi-quantitative serum procalcitonin test on admission. The demographic characteristics; laboratory biomarkers; microbiological test results; Pneumonia Severity Index scores; confusion, urea nitrogen, breathing frequency, blood pressure, ≥ 65 years of age (CURB-65) scale scores; and age, dehydration, respiratory failure, orientation disturbance, pressure (A-DROP) scale scores on hospital admission were retrieved from their medical charts. The outcomes were mortality within 28 days of hospital admission and the need for intensive care. Of the 213 subjects with CAP who were enrolled in the study, 20 died within 28 days of hospital admission, and 32 required intensive care. Mortality did not differ significantly among subjects with different semi-quantitative serum procalcitonin levels; however, subjects with serum procalcitonin levels ≥ 10.0 ng/mL were more likely to require intensive care than those with lower levels (P < .001). The elevation of semi-quantitative serum procalcitonin levels was more frequently observed in subjects with proven etiology, especially pneumococcal pneumonia. Using the receiver operating characteristic curves for mortality, the area under the curve was 0.86 for Pneumonia Severity Index class, 0.81 for B/A ratio, 0.81 for A-DROP, 0.80 for CURB-65, and 0.57 for semi-quantitative procalcitonin test. The semi-quantitative serum procalcitonin level on hospital admission was less predictive of mortality from CAP compared with the B/A ratio. However, the subjects with serum procalcitonin levels ≥ 10.0 ng/mL were more likely to require intensive care than those with lower levels.

Mechanisms of selective antitumor action of cold atmospheric plasma

NASA Astrophysics Data System (ADS)

Graves, David; Bauer, Georg

2016-09-01

Transformed (precancerous) cells are known to be subject to elimination through intercellular RONS-dependent apoptosis-inducing signaling. It is a remarkable fact that the chemical species utilized by apoptosis induction in transformed cells are essentially identical to chemical species created by cold atmospheric plasma (CAP) in aqueous solutions. The association between CAP-induced biochemistry and natural cell anti-tumor mechanisms offers the opportunity to establish a rationale for the observed successes of CAP in selectively eliminating tumor cells in vitro and in vivo. In particular, 1O2 appears to act to selectively induce apoptosis in tumor cells, and can also result in self-perpetuating, cell-to-cell apoptotic signaling. Various CAP-generated liquid phase species can react to form 1O2, thus providing a hypothetical mechanism to explain how CAP can trigger therapeutic apoptosis in tumors. The analysis of model experiments performed with defined RONS in vitro implies that CAP-derived 1O2 induces the mechanism through which CAP acts selectively against cancer cells in vitro and tumors in vivo. This hypothesis needs to be tested experimentally in order to establish its validity.

Discordance of physician clinical judgment vs. pneumonia severity index (PSI) score to admit patients with low risk community-acquired pneumonia: a prospective multicenter study.

PubMed

Marcos, Pedro J; Restrepo, Marcos I; González-Barcala, Francisco J; Soni, Nilam J; Vidal, Iria; Sanjuàn, Pilar; Llinares, Diego; Ferreira-Gonzalez, Lucía; Rábade, Carlos; Otero-González, Isabel; Marcos, Pedro; Verea-Hernando, Héctor

2017-06-01

The relationship between clinical judgment and the pneumonia severity index (PSI) score in deciding the site of care for patients with community-acquired pneumonia (CAP) has not been well investigated. The objective of the study was to determine the clinical factors that influence decision-making to hospitalize low-risk patients (PSI ≤2) with CAP. An observational, prospective, multicenter study of consecutive CAP patients was performed at five hospitals in Spain. Patients admitted with CAP and a PSI ≤2 were identified. Admitting physicians completed a patient-specific survey to identify the clinical factors influencing the decision to admit a patient. The reason for admission was categorized into 1 of 6 categories. We also assessed whether the reason for admission was associated with poorer clinical outcomes [intensive care unit (ICU) admission, 30-day mortality or readmission]. One hundred and fifty-five hospitalized patients were enrolled. Two or more reasons for admission were seen in 94 patients (60.6%), including abnormal clinical test results (60%), signs of clinical deterioration (43.2%), comorbid conditions (28.4%), psychosocial factors (28.4%), suspected H1N1 pneumonia (20.6%), and recent visit to the emergency department (ED) in the past 2 weeks (7.7%). Signs of clinical deterioration and abnormal clinical test results were associated with poorer clinical outcomes (P<0.005). Low-risk patients with CAP and a PSI ≤2 are admitted to the hospital for multiple reasons. Abnormal clinical test results and signs of clinical deterioration are two specific reasons for admission that are associated with poorer clinical outcomes in low risk CAP patients.

The effect of clay on the dissolution of nuclear waste glass

NASA Astrophysics Data System (ADS)

Lemmens, K.

2001-09-01

In a nuclear waste repository, the waste glass can interact with metals, backfill materials (if present) and natural host rock. Of the various host rocks considered, clays are often reported to delay the onset of the apparent glass saturation, where the glass dissolution rate becomes very small. This effect is ascribed to the sorption of silica or other glass components on the clay. This can have two consequences: (1) the decrease of the silica concentration in solution increases the driving force for further dissolution of glass silica, and (2) the transfer of relatively insoluble glass components (mainly silica) from the glass surface to the clay makes the alteration layer less protective. In recent literature, the latter explanation has gained credibility. The impact of the environmental materials on the glass surface layers is however not well understood. Although the glass dissolution can initially be enhanced by clay, there are arguments to assume that it will decrease to very low values after a long time. Whether this will indeed be the case, depends on the fate of the released glass components in the clay. If they are sorbed on specific sites, it is likely that saturation of the clay will occur. If however the released glass components are removed by precipitation (growth of pre-existing or new secondary phases), saturation of the clay is less likely, and the process can continue until exhaustion of one of the system components. There are indications that the latter mechanism can occur for varying glass compositions in Boom Clay and FoCa clay. If sorption or precipitation prevents the formation of protective surface layers, the glass dissolution can in principle proceed at a high rate. High silica concentrations are assumed to decrease the dissolution rate (by a solution saturation effect or by the impact on the properties of the glass alteration layer). In glass corrosion tests at high clay concentrations, silica concentrations are, however, often higher than the silica concentrations in equilibrium with the glass surface ( C ∗Si, saturation) that are found in absence of clay. Nevertheless, the glass dissolution proceeds at relatively high rate. C ∗Si, saturation seems to be increased by the presence of clay. To understand this, more knowledge is necessary concerning the fate of the released silica and the silica speciation in solution.

MODIFIED REVERSE OSMOSIS SYSTEM FOR TREATMENT OF PRODUCED WATERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

T.M. Whitworth; Liangxiong Li

2002-09-15

This report describes work performed during the first year of the project ''Modified Reverse Osmosis System for Treatment of Produced Waters.'' This research project has two objectives. The first objective is to test the use of clay membranes in the treatment of produced waters by reverse osmosis. The second objective is to test the ability of a system patented by the New Mexico Tech Research Foundation to remove salts from reverse osmosis waste streams as a solid. We performed 12 experiments using clay membranes in cross-flow experimental cells. We found that, due to dispersion in the porous frit used adjacentmore » to the membrane, the concentration polarization layer seems to be completely (or nearly completely) destroyed at low flow rates. This observation suggests that clay membranes used with porous frit material many reach optimum rejection rates at lower pumping rates than required for use with synthetic membranes. The solute rejection efficiency decreases with increasing solution concentration. For the membranes and experiments reported here, the rejection efficiency ranged from 71% with 0.01 M NaCl solution down to 12% with 2.3 M NaCl solution. More compacted clay membranes will have higher rejection capabilities. The clay membranes used in our experiments were relatively thick (approximately 0.5 mm). The active layer of most synthetic membranes is only 0.04 {micro}m (0.00004 mm), approximately 1250 times thinner than the clay membranes used in these experiments. Yet clay membranes as thin as 12 {micro}m have been constructed (Fritz and Eady, 1985). Since Darcy's law states that the flow through a material of constant permeability is inversely proportional to it's the material's thickness, then, based on these experimental observations, a very thin clay membrane would be expected to have much higher flow rates than the ones used in these experiments. Future experiments will focus on testing very thin clay membranes. The membranes generally exhibited reasonable stable rejection rates over time for chloride for a range of concentrations between 0.01 and 2.5 M. One membrane ran in excess of three months with no apparent loss of usability. This suggests that clay membranes may have a long useable life. Twenty different hyperfiltration-induced solute precipitation experiments were either attempted or completed and are reported here. The results of these experiments suggest that hyperfiltration-induced solute precipitation is possible, even for very soluble substances such as NaCl. However, the precipitation rates obtained in the laboratory do not appear to be adequate for commercial application at this time. Future experiments will focus on making the clay membranes more compact and thinner in order to obtain higher flux rates. Two alternative methods of removing solutes from solution, for which the New Mexico Tech Research Foundation is preparing patent applications, are also being investigated. These methods will be described in the next annual report after the patent applications are filed. Technology transfer efforts included two meetings (one in Farmington NM, and one in Hobbs, NM) where the results of this research were presented to independent oil producers and other interested parties. In addition, members of the research team gave seven presentations concerning this research and because of this research project T. M. (Mike) Whitworth was asked to sit on the advisory board for development of a new water treatment facility for the City of El Paso, Texas. Several papers are in preparation for submission to peer-reviewed journals based on the data presented in this report.« less

Evaluating Weathering of Food Packaging Polyethylene-Nano-clay Composites: Release of Nanoparticles and their Impacts.

PubMed

Han, Changseok; Zhao, Amy; Varughese, Eunice; Sahle-Demessie, E

2018-01-01

Nano-fillers are increasingly incorporated into polymeric materials to improve the mechanical, barrier or other matrix properties of nanocomposites used for consumer and industrial applications. However, over the life cycle, these nanocomposites could degrade due to exposure to environmental conditions, resulting in the release of embedded nanomaterials from the polymer matrix into the environment. This paper presents a rigorous study on the degradation and the release of nanomaterials from food packaging composites. Films of nano-clay-loaded low-density polyethylene (LDPE) composite for food packaging applications were prepared with the spherilene technology and exposed to accelerated weathering of ultraviolet (UV) irradiation or low concentration of ozone at 40 °C. The changes in the structural, surface morphology, chemical and physical properties of the films during accelerated weathering were investigated. Qualitative and quantitative changes in properties of pristine and aged materials and the release of nano-clay proceeded slowly until 130 hr irradiation and then accelerated afterward resulting complete degradation. Although nano-clay increased the stability of LDPE and improved thermal and barrier properties, they accelerated the UV oxidation of LDPE. With increasing exposure to UV, the surface roughness, chemiluminescence index, and carbonyl index of the samples increased while decreasing the intensity of the wide-angle X-ray diffraction pattern. Nano-clay particles with sizes ranging from 2-8 nm were released from UV and ozone weathered composite. The concentrations of released nanoparticles increased with an increase in aging time. Various toxicity tests, including reactive oxygen species generation and cell activity/viability were also performed on the released nano-clay and clay polymer. The released nano-clays basically did not show toxicity. Our combined results demonstrated the degradation properties of nano-clay particle-embedded LDPE composites toxicity of released nano-clay particles to A594 adenocarcinomic human alveolar basal epithelial cells was observed, which will help with future risk based-formulations of exposure.

A shovel with a perforated blade reduces energy expenditure required for digging wet clay.

PubMed

Harivanam, Sridhar; Marklin, Richard W; Papanek, Paula E; Cariapa, Vikram

2010-08-01

A shovel with a blade perforated with small holes was tested to see whether a worker would use less whole-body energy to dig wet clay than with a shovel with an opaque blade. A perforated shovel is hypothesized to require less whole-body energy on the basis of adhesion theory; a smaller surface area would require less physical effort to dig and release soil from the blade. The study involved 13 workers from an electric utility who dug wet clay with two 1.5-m long-handled point shovels, which differed only in blade design (perforated and opaque). Oxygen consumption was measured with a portable system while each worker dug wet clay at a self-regulated pace for 10 min. There was no significant difference in number of scoops dug during the 10-min sessions, but workers dug 9.5% more weight of clay with the perforated shovel than with the conventional shovel (404 kg vs. 369 kg, respectively). Furthermore, stable oxygen uptake normalized to weight of participant and to the weight of clay dug revealed that participants expended 11.7% less relative energy per kilogram of clay dug with the perforated shovel. A point shovel with a perforated blade is recommended for digging and shoveling wet clay. However, the extra weight that workers chose to dig with the perforated shovel may increase the loading on the spine and may offset the metabolic advantages. Manual shoveling is a common task, and workers may experience less whole-body and muscle fatigue when using a perforated shovel.

Decolorization of Methyl Orange by a new clay-supported nanoscale zero-valent iron: Synergetic effect, efficiency optimization and mechanism.

PubMed

Li, Xiaoguang; Zhao, Ying; Xi, Beidou; Meng, Xiaoguang; Gong, Bin; Li, Rui; Peng, Xing; Liu, Hongliang

2017-02-01

In this study, a novel nanoscale zero-valent iron (nZVI) composite material was successfully synthesized using a low-cost natural clay, "Hangjin 2 # clay" (HJ clay) as the support and tested for the decolorization of the azo dye Methyl Orange (MO) in aqueous solution by nZVI particles. According to the characterization and MO decolorization experiments, the sample with 5:1 HJ clay-supported nZVI (HJ/nZVI) mass ratio (HJ-nZVI5) showed the best dispersion and reactivity and the highest MO decolorization efficiency. With the same equivalent Fe 0 dosage, the HJ-nZVI1 and HJ-nZVI5 samples demonstrated a synergetic effect for the decolorization of MO: their decolorization efficiencies were much higher than that achieved by physical mixing of HJ clay and nZVIs, or the sum of HJ clay and nZVIs alone. The synergetic effect was primarily due to the improved dispersion and more effective utilization of the nZVI particles on/in the composite materials. Higher decolorization efficiency of MO was obtained at larger HJ-nZVI dosage, higher temperature and under N 2 atmosphere, while the MO initial concentration and pH were negatively correlated to the efficiency. HJ clay not only works as a carrier for nZVI nanoparticles, but also contributes to the decolorization through an "adsorption-enhanced reduction" mechanism. The high efficiency of HJ-nZVI for decontamination gives it great potential for use in a variety of remediation applications. Copyright © 2016. Published by Elsevier B.V.

Combined Mini-Cylex & Disk Acceleration Tests in Type K Copper

DOE PAGES

Maines, Warren Russell; Kittell, David E.; Hobbs, Michael L.

2018-04-16

In this work, we combined the miniature cylinder expansion test (Mini-Cylex), with the Disk Acceleration Test (DAX) using Type K copper, Picatinny Liquid Explosive, and photonic Doppler velocimetry. We estimated the CJ state using plate reverberation methods at the test cap. We extracted velocities at 2, 7, and 10 volume expansions to fit Jones-Wilkins-Lee Equation of State and estimated Gurney velocity at the tube wall. The test also provides an additional method to estimate reaction products Hugoniot through knowledge of the copper test cap. Our experiments and simulations are within expected uncertainty. Lastly, the test and the analysis effectively reducemore » costs while keeping or increasing fidelity.« less

Combined Mini-Cylex & Disk Acceleration Tests in Type K Copper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maines, Warren Russell; Kittell, David E.; Hobbs, Michael L.

In this work, we combined the miniature cylinder expansion test (Mini-Cylex), with the Disk Acceleration Test (DAX) using Type K copper, Picatinny Liquid Explosive, and photonic Doppler velocimetry. We estimated the CJ state using plate reverberation methods at the test cap. We extracted velocities at 2, 7, and 10 volume expansions to fit Jones-Wilkins-Lee Equation of State and estimated Gurney velocity at the tube wall. The test also provides an additional method to estimate reaction products Hugoniot through knowledge of the copper test cap. Our experiments and simulations are within expected uncertainty. Lastly, the test and the analysis effectively reducemore » costs while keeping or increasing fidelity.« less

Evaluation of the attenuating properties of selected Greek clays for toxic inorganic elements in landfill sites.

PubMed

Mimides, T; Perraki, T

2000-05-15

Heavy metal attenuation properties of selected clay material collected from miscellaneous Greek sites is investigated and tested in the laboratory for their suitability, either as liners in hydrologically unsafe sites or as earth covers for sanitary landfill sites. Eleven potentially hazardous elements (As, Be, Cd, Cr, Cu, Hg, Ni, Pb, Se, V, and Zn) generated by a co-disposal landfill leachate have been considered. Experimental column and static equilibrium methods for the determination of dispersion and adsorption are described. Molecular diffusion dominates the migration phenomena with a velocity range between 1.3 x 10(-5) and 3.5 x 10(-4) cm/s throughout the experiments. A simple way to evaluate dispersion coefficients from breakthrough curves gave values of between 3.90 x 10(-6) and 3.5 x 10(-4) cm2/s, with a mean value of 1.5 x 10(-5). Static adsorption equilibrium studies supported by column runs showed that Freundlich (F = kCn) isotherms express in a better way the assimilative capacities of the tested clays, with k and n values ranging from 0.06 to 1.99 and 0.55 to 1.48 correspondingly. Mathematical models involving non-linear parabolic equations are involved. The experimental data, together with finite difference techniques and some physical clay characteristics, produced trilinear textural diagrams and predictive flow transport convection-dispersion breakthrough curves for a quick estimation of the attenuating properties of clays for heavy metals.

[X-ray diffraction and infrared spectrum analysis of fault gouge in Wenchuan seismic belt].

PubMed

Wang, Zheng-Yang; Cao, Jian-Jin; Luo, Song-Ying; Liao, Yi-Peng

2014-05-01

Wenchuan earthquake produced a series of co-seismic surface ruptures in Leigu and Zhaojiagou, and we collected samples of co-seismic fault gouge in the surface ruptures as well as the old gouge in the fault of Nanba. Testing The new and old fault gouge was tested with X-ray diffraction and infrared absorption spectra, and its characteristics such as mineral compositions, clay mineral contents and combinations were comprehensively analyzed. The results display obvious differences between the new and old fault gouge, showing that the old fault gouge is mainly composed of wall rock debris or milled powders, while the main components of new fault gouge are clay minerals. The assemblage of clay minerals composition shows that the environment of the fault activity was mainly warm and humid, and the clay minerals were mainly transformed by low temperature and low pressure dynamic metamorphism. And this also partly indicates that the latest way of the fault activity in this area may be a creeping. However the previous researches on the fault gouge of Wenchuan earthquake fault zone are mainly focused on its mechanical properties as well as its texture and structure, the research in this paper is to determine the physical and chemical environment of fault activity through the mineral compositions and clay mineral contents in the fault gouge characteristics, and this research has important scientific significance to the researches on the evolution of the fault environment and the activity mechanism of the earthquake.

Lightweight aggregate production from claystone and shale in Bangladesh

USGS Publications Warehouse

Parker, Norbert A.; Khan, M.A.

1976-01-01

Muffle furnace tests were made on samples of clay, claystone, and shale collected in the Chittagong and Dacca areas of East Pakistan to determine their amenability to bloating for the commercial production of light-weight aggregate. Several areas, sampled in some detail, were selected for investigation because of their proximity to market, and accessibility to fuel and electricity. Muffle furnace tests show that the clay, claystone, and shale are natural bloaters at temperatures in the 1700? to 2200? F range, and do not require additives. The most desirable deposit, insofar as producing a strong aggregate is concerned, can be determined only by pilot-kiln testing and by crushing-strength tests made on concrete test cylinders. Reserves of suitable raw material are large in both the Chittagong and Dacca areas.

Risk factors for latex allergy in patients with spina bifida and latex sensitization.

PubMed

Bernardini, R; Novembre, E; Lombardi, E; Mezzetti, P; Cianferoni, A; Danti, D A; Mercurella, A; Vierucci, A

1999-05-01

Some subjects with spina bifida (SB) and latex sensitization (cutaneous and/or serum IgE) can have clinical reactions, while others may have no symptoms after the exposure to latex products. This study was carried out to determine the risk factors associated with latex allergy in patients affected with SB and latex sensitization. Fifty-nine consecutive subjects affected with SB, besides answering a questionnaire, underwent a skin-prick test (SPT) to latex and the determination of the specific serum IgE (RAST CAP) to latex. The total serum IgE concentration was determined and SPT to common aero- and food-allergens, skin tests (prick + prick) with fresh foods (kiwi, pear, orange, pineapple, tomato, banana) and RAST CAP to the same foods tested by the prick + prick technique, were also performed. Fifteen out of the 59 subjects (25%) were sensitized to latex according to the presence of IgE to latex detected by SPT (nine patients) and/or RAST CAP (13 patients). Five out of the 15 sensitized patients (33%) suffered from clinical reactions to latex (urticaria, conjunctivitis, angioedema, rhinitis, bronchial asthma) while they were using latex gloves and while inflating latex balloons. In the 15 sensitized patients, the presence of specific latex seric IgE > 3.5 kU/L (>/= class 3), a positive latex SPT, an elevated total serum IgE, and a positive prick + prick and/or a positive RAST CAP to foods, were significant (P < 0.05) risk factors associated with latex symptoms. The other factors tested (age, gender, months of intermittent bladder catheterization, surgical procedures, SPT reactivity and clinical reactions to aero-allergens and food-allergens, skin tests for fresh foods, positive RAST CAP to foods) were not significantly different in symptomatic and asymptomatic patients. Significant risk factors for symptoms to latex in patients with SB and latex sensitization were a presence of specific IgE to latex > 3.5 kU/L, a more frequent positive latex SPT, elevated total IgE, and one or more positive prick + prick and/or RAST CAP to fresh foods.

Sensors for the End-cap prototype of the Inner Tracker in the ATLAS Detector Upgrade

NASA Astrophysics Data System (ADS)

Benítez, V.; Ullán, M.; Quirion, D.; Pellegrini, G.; Fleta, C.; Lozano, M.; Sperlich, D.; Hauser, M.; Wonsak, S.; Parzefall, U.; Mahboubi, K.; Kuehn, S.; Mori, R.; Jakobs, K.; Bernabeu, J.; García, C.; Lacasta, C.; Marco, R.; Rodriguez, D.; Santoyo, D.; Solaz, C.; Soldevila, U.; Ariza, D.; Bloch, I.; Diez, S.; Gregor, I. M.; Keller, J.; Lohwasser, K.; Peschke, R.; Poley, L.; Brenner, R.; Affolder, A.

2016-10-01

The new silicon microstrip sensors of the End-cap part of the HL-LHC ATLAS Inner Tracker (ITk) present a number of challenges due to their complex design features such as the multiple different sensor shapes, the varying strip pitch, or the built-in stereo angle. In order to investigate these specific problems, the "petalet" prototype was defined as a small End-cap prototype. The sensors for the petalet prototype include several new layout and technological solutions to investigate the issues, they have been tested in detail by the collaboration. The sensor description and detailed test results are presented in this paper. New software tools have been developed for the automatic layout generation of the complex designs. The sensors have been fabricated, characterized and delivered to the institutes in the collaboration for their assembly on petalet prototypes. This paper describes the lessons learnt from the design and tests of the new solutions implemented on these sensors, which are being used for the full petal sensor development. This has resulted in the ITk strip community acquiring the necessary expertise to develop the full End-cap structure, the petal.

Stratigraphic Evolution of Brazos-Trinity Basin IV, Western Gulf of Mexico: Preliminary Results of IODP Expedition 308

NASA Astrophysics Data System (ADS)

Pirmez, C.; Behrmann, J.; Flemings, P. B.; John, C.

2005-12-01

IODP Expedition 308 drilled three sites across Brazos-Trinity Basin IV, at the terminal end of a system of four salt-withdrawal intra-slope basins offshore Texas. A 175 m thick succession of sand-rich turbidite fans, mass-transport deposits and hemipelagic sediments was deposited within the last ~120 ka in Basin IV, as recorded at Site U1320. Pre-fan deposits dating back to MIS 6 form a conformable succession of laminated and bioturbated clays, deposited from distal turbidity currents and/or river plumes. The pre-fan succession is capped by a hemipelagic clay interpreted to represent the high stand of sea level during MIS 5e. The basal turbidite deposits in the basin are mud-rich, with the exception of the very first turbidity currents to enter the basin. This initial pulse, possibly derived from failure of older shelf edge deposits, accumulated an ~8 m thick sand-rich interval. A pause in turbidity current influx lasted 30 to 40 kyrs, beginning a few thousand years before ash layer Y8 dated at 84 ka and the Emiliana huxleyi acme. During MIS 3 to MIS 2 sand-rich fans containing 5-25 m thick packets of very fine to lower medium sand beds accumulated up to 130 m of sediments. A 2-3 m thick microfossil-rich clay marks the end of turbidity current influx into the basin during the Holocene. The sedimentary record of Brazos-Trinity Basin IV shows that the accumulation of turbidites in the terminal end of this source to sink depositional system reflects a complex interaction between the availability of material and the initiation of flows at the source near the shelf edge, the interaction of turbidity currents with complex slope topography, and the effects of salt tectonics and flow processes on modifying this topography. The initial results indicate that sealevel changes alone cannot explain the sedimentation patterns observed in the basin.

Environmental magnetism of intertrapean Deccan deposits: unravelling local paleoenvironmental during Phase 1 and 2

NASA Astrophysics Data System (ADS)

Font, Eric; Adatte, Thierry; Ponte, Jorge; Fantasia, Alicia; Mirão, José; Samant, Bandana; Mohabey, Dhananjay; Florindo, Fabio

2014-05-01

The Deccan phase 2 is a crucial period caracterized by the rapid eruptions of huge volume of continental flood basalts correlated in age to the mass extinction of the Cretaceous-Paleogene boundary. However, local to global paleonvironmental changes during the Deccan Phase 2 are still baddly known. Here we provide new environmental magnetic data coupled to scanning electron microscopy of intertrapean deposits from the Deccan Volcanic Province (India) in order to unravel local paleoenvironmental conditions during periods of volcanic quiescence in the aftermath of the Deccan Phase 1 and Phase 2. Our results show that the magnetic mineralogy of these lacustrine and fluvial sediments is composed by several populations of iron oxides and sulphur, with a large range of grain size, probably resulting from different source of magnetic carriers (aeolian, detrital and bio-chemical). The number of magnetic phases identified using unmixing Isothermal Remanence Magnetic techniques is significantly higher (2 to 4) in the Podgavan section equivalent to Phase 2 than in the other studied sections, interpreted to result from higher weathering rates (acidity) by correlation with index of chemical alteration. Detailed scanning electron microscopy analysis of the Podgavan section reveal a complex mineralogy constituted by detrital magnetite, spherical and framboidal magnetite, microsphere of silicon, pyrrhotite, sylvite, manganese oxides and sporangiospores. A peculiar interval observed in the middle part of the Podgavan section, and corresponding to a thin interval of organic-rich clay capped by a thin oxidized level of reddish clays, show the presence of calcite needles and very fine hematite pigment. Hematite pigment are systematically associated to voids and form structures comparable to the blueberry hematite formed on mars. The abrupt transition from organic-rich levels (reducing conditions) to red hematitic clays (oxidation) suggests drastic and abrupt paleoenvironmental changes and acid conditions during the Deccan Phase 2. Keywords: Deccan, lacustrine sediments, environmental magnetism, acid rain, climate, weathering, volcanism.

Transduction of the Root Gravitropic Stimulus: Can Apical Calcium Regulate Auxin Distribution?

NASA Technical Reports Server (NTRS)

Edwards, K. L.

1985-01-01

The hypothesis was tested that calcium, asymmetrically distributes in the root cap upon reorientation to gravity, affects auxin transport and thereby auxin distribution at the elongation zone. It is assumed that calcium exists in the root cap and is asymmetrically transported in root caps altered from a vertical to a horizontal position and that the meristem, the tissue immediately adjacent to the root cap and lying between the site of gravity perception and the site of gravity response, is essential for mediation of gravitropism. Tip calcium in root gravicurvature was implicated. The capstone evidence is that the root cap has the capacity to polarly translocate exogenous calcium downward when tissue is oriented horizontally, and that exogenous calcium, when supplied asymmetrically at the root tip, induces curvature and dictates the direction of curvature in both vertical and horizontal corn roots.

Biologic Potential of Calcium Phosphate Biopowders Produced via Decomposition Combustion Synthesis

PubMed Central

Vollmer, N.; King, K.B.; Ayers, R.

2015-01-01

The aim of this research was to evaluate the biologic potential of calcium phosphate (CaP) biopowders produced with a novel reaction synthesis system. Decomposition combustion synthesis (DCS) is a modified combustion synthesis method capable of producing CaP powders for use in bone tissue engineering applications. During DCS, the stoichiometric ratio of reactant salt to fuel was adjusted to alter product chemistry and morphology. In vitro testing methods were utilized to determine the effects of controlling product composition on cytotoxicity, proliferation, biocompatibility and biomineralization. In vitro, human fetal osteoblasts (ATCC, CRL-11372) cultured with CaP powder displayed a flattened morphology, and uniformly encompassed the CaP particulates. Matrix vesicles containing calcium and phosphorous budded from the osteoblast cells. CaP powders produced via DCS are a source of biologically active, synthetic, bone graft substitute materials PMID:26034341

Apparatuses for prestressing rod-type specimens in torsion for in-situ passive fracture toughness testing in an extremely high-pressure environment of hydrogen

DOEpatents

Wang, Jy-an [Oak Ridge, TN; Liu, Ken C [Oak Ridge, TN; Feng, Zhili [Knoxville, TN

2012-05-15

An in-situ specimen fixture particularly adapted for prestressing rod-type SNTT-type specimens comprising a tube and end cap wherein the specimen is secured at one end to the tube, and at the opposite end to the end cap. The end cap is rotatable relative to the tube, and may be fixedly secured for creating a torsional force prestressing the specimen enclosed within the tube.

Study on Fired Clay Bricks by Replacing Clay with Palm Oil Waste: Effects on Physical and Mechanical Properties

NASA Astrophysics Data System (ADS)

Kadir, A. A.; Sarani, N. A.; Abdullah, M. M. A. B.; Perju, M. C.; Sandu, A. V.

2017-06-01

Palm oil is one of the major agricultural industries in Malaysia. Due to the poor management system, the discarded palm oil waste has always been linked to the environment issues. During processing of palm oil, a considerable amount of solid waste by-products in the form of fibres, shells, empty fruit bunches and fly ashes are produce rapidly. Therefore, this study was conducted to incorporate 1%, 5% and 10% of palm oil waste into fired clay brick. Samples of brick were fired at 1050°C temperature with heating rates of 1°C/min. Manufactured bricks were tested with physical and mechanical properties including firing shrinkage, dry density, water absorption and compressive strength. The results demonstrated that the replacement of 1% up to 5% of palm oil waste had improved several properties, although, a decrease of performance in certain aspects has also been observed. As a result, palm oil waste can be utilized in an environmentally safe way into fired clay brick thus providing adequate properties of fired clay brick.

Evaluation of clay/poly (L-lactide) microcomposites as anticancer drug, 6-mercaptopurine reservoir through in vitro cytotoxicity, oxidative stress markers and in vivo pharmacokinetics.

PubMed

Kevadiya, Bhavesh D; Chettiar, Shiva Shankaran; Rajkumar, Shalini; Bajaj, Hari C; Gosai, Kalpeshgiri A; Brahmbhatt, Harshad

2013-12-01

Intercalation of 6-mercaptopurine (6-MP), an antineoplastic drug in interlayer gallery of Na(+)-clay (MMT) was further entrapped in poly (L-lactide) matrix to form microcomposite spheres (MPs) in order to reduce the cell toxicity and enhance in vitro release and pharmacokinetic proficiency. The drug-clay hybrid was fabricated via intercalation by ion-exchange method to form MPs from hybrid. In vitro drug release showed controlled pattern, fitted to kinetic models suggested controlled exchange and partial diffusion through swollen matrix of clay inter layered gallery. The in vitro efficacy of formulated composites drug was tested in Human neuroblastoma cell line (IMR32) by various cell cytotoxic and oxidative stress marker indices. In vivo pharmacokinetics suggested that the intensity of formulated drug level in plasma was within remedial borders as compared to free drug. These clay based composites therefore have great potential of becoming a new dosage form of 6-MP. Copyright © 2013 Elsevier B.V. All rights reserved.

Preparation and characterization of electron-beam treated HDPE composites reinforced with rice husk ash and Brazilian clay

NASA Astrophysics Data System (ADS)

Ortiz, A. V.; Teixeira, J. G.; Gomes, M. G.; Oliveira, R. R.; Díaz, F. R. V.; Moura, E. A. B.

2014-08-01

This work evaluates the morphology, mechanical and thermo-mechanical properties of high density polyethylene (HDPE) composites. HDPE reinforced with rice husk ashes (80:20 wt%), HDPE reinforced with clay (97:3 wt%) and HDPE reinforced with both rice husk ashes and clay(77:20:3 wt%) were obtained. The Brazilian bentonite chocolate clay was used in this study. This Brazilian smectitic clay is commonly used to produce nanocomposites. The composites were produced by melting extrusion process and then irradiation was carried out in a 1.5 MeV electron-beam accelerator (room temperature, presence of air). Comparisons using the irradiated and non-irradiated neat polymer, and the irradiated and non-irradiated composites were made. The materials obtained were submitted to tensile, flexural and impact tests. Additionally HDT, SEM and XRD analyses were carried out along with the sol-gel analysis which aimed to assess the cross-linking degree of the irradiated materials. Results showed great improvement in most HDPE properties and a high cross-linking degree of 85% as a result of electron-beam irradiation of the material.

Chemical remagnetization and clay diagenesis: testing the hypothesis in the Cretaceous sedimentary rocks of northwestern Montana

NASA Astrophysics Data System (ADS)

Gill, J. D.; Elmore, R. D.; Engel, M. H.

Although the migration of fluids is a likely agent of remagnetization for some chemical remanent magnetizations (CRMs), widespread CRMs, which occur in rocks that have not been altered by externally derived fluids, need to explained by another mechanism. We are testing clay diagenesis as a remagnetization mechanism for such CRMs by comparing results from Mesozoic strata in the disturbed belt of Montana where the rocks contain ordered illite/smectite that formed by moderate heating as a result of thrust loading, with equivalent strata on the adjacent Sweetgrass Arch which contain unaltered smectite-rich clay mineral assemblages. The results indicate that the magnetization in the rocks in the Sweetgrass Arch is weak and dominated by a modern viscous component. In contrast, the disturbed belt rocks have higher magnetic intensities and contain a prefolding or early synfolding, reversed tertiary magnetization that is interpreted to be a CRM residing in magnetite and perhaps pyrrhotite. A presence-absence test and the timing of acquisition for the CRM suggest that magnetite authigenesis could be related to the smectite-to-illite conversion.

Diagnostic criteria for cryopyrin-associated periodic syndrome (CAPS).

PubMed

Kuemmerle-Deschner, Jasmin B; Ozen, Seza; Tyrrell, Pascal N; Kone-Paut, Isabelle; Goldbach-Mansky, Raphaela; Lachmann, Helen; Blank, Norbert; Hoffman, Hal M; Weissbarth-Riedel, Elisabeth; Hugle, Boris; Kallinich, Tilmann; Gattorno, Marco; Gul, Ahmet; Ter Haar, Nienke; Oswald, Marlen; Dedeoglu, Fatma; Cantarini, Luca; Benseler, Susanne M

2017-06-01

Cryopyrin-associated periodic syndrome (CAPS) is a rare, heterogeneous disease entity associated with NLRP3 gene mutations and increased interleukin-1 (IL-1) secretion. Early diagnosis and rapid initiation of IL-1 inhibition prevent organ damage. The aim of the study was to develop and validate diagnostic criteria for CAPS. An innovative process was followed including interdisciplinary team building, item generation: review of CAPS registries, systematic literature review, expert surveys, consensus conferences for item refinement, item reduction and weighting using 1000Minds decision software. Resulting CAPS criteria were tested in large cohorts of CAPS cases and controls using correspondence analysis. Diagnostic models were explored using sensitivity analyses. The international team included 16 experts. Systematic literature and registry review identified 33 CAPS-typical items; the consensus conferences reduced these to 14. 1000Minds exercises ranked variables based on importance for the diagnosis. Correspondence analysis determined variables consistently associated with the diagnosis of CAPS using 284 cases and 837 controls. Seven variables were significantly associated with CAPS (p<0.001). The best diagnosis model included: Raised inflammatory markers (C-reactive protein/serum amyloid A) plus ≥two of six CAPS-typical symptoms: urticaria-like rash, cold-triggered episodes, sensorineural hearing loss, musculoskeletal symptoms, chronic aseptic meningitis and skeletal abnormalities. Sensitivity was 81%, specificity 94%. It performed well for all CAPS subtypes and regardless of NLRP3 mutation. The novel approach integrated traditional methods of evidence synthesis with expert consensus, web-based decision tools and innovative statistical methods and may serve as model for other rare diseases. These criteria will enable a rapid diagnosis for children and adults with CAPS. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Phosphates in some Missouri refractory clays

USGS Publications Warehouse

Halley, Robert B.; Foord, Eugene E.; Keller, David J.; Keller, Walter D.

1997-01-01

This paper describes in detail phosphate minerals occurring in refractory clays of Missouri and their effect on the refractory degree of the clays. The minerals identified include carbonate-fluorapatite (francolite), crandallite, goyazite, wavellite, variscite and strengite. It is emphasized that these phosphates occur only in local isolated concentrations, and not generally in Missouri refractory clays.The Missouri fireclay region comprises 2 districts, northern and southern, separated by the Missouri River. In this region, clay constitutes a major part of the Lower Pennsylvanian Cheltenham Formation. The original Cheltenham mud was an argillic residue derived from leaching and dissolution of pre-Pennsylvanian carbonates. The mud accumulated on a karstic erosion surface truncating the pre-Cheltenham rocks. Fireclays of the northern district consist mainly of poorly ordered kaolinite, with variable but minor amounts of illite, chlorite and fine-grained detrital quartz. Clays of the southern district were subjected to extreme leaching that produced well-ordered kaolinite flint clays. Local desilication formed pockets of diaspore, or more commonly, kaolinite, with oolite-like nubs or burls of diaspore (“burley”" clay).The phosphate-bearing materials have been studied by X-ray diffraction (XRD), scanning electron microscopy-energy dispersive spectral analysis (SEM-EDS) and chemical analysis. Calcian goyazite was identified in a sample of diaspore, and francolite in a sample of flint clay. A veinlet of wavellite occurs in flint clay at one locality, and a veinlet of variscite-strengite at another locality.The Missouri flint-clay-hosted francolite could not have formed in the same manner as marine francolite. The evidence suggests that the Cheltenham francolite precipitated from ion complexes in pore water, nearly simultaneously with crystallization of kaolinite flint clay from an alumina-silica gel. Calcian goyazite is an early diagenetic addition to its diaspore host. The wavellite and variscite-strengite veinlets are secondary, precipitated from ion complexes in ground water percolating along cracks in the flint clay. The flint clay host of the variscite-strengite veinlet contains strontian crandallite. All of the phosphates contain significant amounts of strontium. The source of P, Ca and Sr was the marine carbonates. Dissolution of these carbonates produced the argillic residue that became the primordial Cheltenham paludal mud, which ultimately altered to fireclay.Preliminary firing tests show that the presence of phosphates lowers fusion temperature. However, it is not clear whether poor refractoriness is due to the presence of phosphates, per se, or to Ca, Sr and other alkaline elements present in the phosphates.

Pyrolysis of attapulgite clay blended with yak dung enhances pasture growth and soil health: Characterization and initial field trials.

PubMed

Rafiq, Muhammad Khalid; Joseph, Stephen D; Li, Fei; Bai, Yanfu; Shang, Zhanhuan; Rawal, Aditya; Hook, James M; Munroe, Paul R; Donne, Scott; Taherymoosavi, Sara; Mitchell, David R G; Pace, Ben; Mohammed, Mohanad; Horvat, Joseph; Marjo, Christopher E; Wagner, Avital; Wang, Yanlong; Ye, Jun; Long, Rui-Jun

2017-12-31

Recent studies have shown that the pyrolysis of biomass combined with clay can result in both lower cost and increase in plant yields. One of the major sources of nutrients for pasture growth, as well as fuel and building materials in Tibet is yak dung. This paper reports on the initial field testing in a pasture setting in Tibet using yak dung, biochar, and attapulgite clay/yak dung biochars produced at ratios of 10/90 and 50/50 clay to dung. We found that the treatment with attapulgite clay/yak dung (50/50) biochar resulted in the highest pasture yields and grass nutrition quality. We also measured the properties and yields of mixtures of clay/yak dung biochar used in the field trials produced at 400°C and 500°C to help determine a possible optimum final pyrolysis temperature and dung/clay ratio. It was observed that increasing clay content increased carbon stability, overall biochar yield, pore size, carboxyl and ketone/aldehyde functional groups, hematite and ferrous/ferric sulphate/thiosulphate concentration, surface area and magnetic moment. Decreasing clay content resulted in higher pH, CEC, N content and an enhanced ability to accept and donate electrons. The resulting properties were a complex function of both processing temperature and the percentage of clay for the biochars processed at both 400°C and 500°C. It is possible that the increase in yield and nutrient uptake in the field trial is related to the higher concentration of C/O functional groups, higher surface area and pore volume and higher content of Fe/O/S nanoparticles of multiple oxidation state in the 50/50 clay/dung. These properties have been found to significantly increase the abundance of beneficial microorganisms and hence improve the nutrient cycling and availability in soil. Further field trials are required to determine the optimum pyrolysis production conditions and application rate on the abundance of beneficial microorganisms, yields and nutrient quality. Copyright © 2017 Elsevier B.V. All rights reserved.

An Experimental Investigation of Mechanical Properties in Clay Brick Masonry by Partial Replacement of Fine Aggregate with Clay Brick Waste

NASA Astrophysics Data System (ADS)

Kumavat, Hemraj Ramdas

2016-09-01

The compressive stress-strain behavior and mechanical properties of clay brick masonry and its constituents clay bricks and mortar, have been studied by several laboratory tests. Using linear regression analysis, a analytical model has been proposed for obtaining the stress-strain curves for masonry that can be used in the analysis and design procedures. The model requires only the compressive strengths of bricks and mortar as input data, which can be easily obtained experimentally. Development of analytical model from the obtained experimental results of Young's modulus and compressive strength. Simple relationships have been identified for obtaining the modulus of elasticity of bricks, mortar, and masonry from their corresponding compressive strengths. It was observed that the proposed analytical model clearly demonstrates a reasonably good prediction of the stress-strain curves when compared with the experimental curves.

The Evaluation of Basal Respiration for Various Soil Textures in Ecologically Sensitive Area

NASA Astrophysics Data System (ADS)

Huličová, P.; Kotorová, D.; Fazekašová, D.; Hynšt, J.

2017-10-01

The present contribution was focused on monitoring changes in the soil basal respiration in different textures of soil in the dry polder Beša. The research was conducted between 2012 and 2014 on soil type Fluvisol locations on three soil textures: clay - loam soil, clayey soil and clay soil in three soil depths. The basal respiration (BR) has been determine by soil CO2 production measuring from incubated soil samples in serum bottles in laboratory condition. Release Co2 has been analysed by gas chromatography. Content of clay particles were in the range 52.18 % to 81.31%, indicating the high difference between the minimum and maximum content. By using of multiple LSD-test we recorded statistically significant impact of clay on basal respiration. Results confirm the values of basal respiration with the depth of the soil profile decreased.

Halloysite clay nanotubes for resveratrol delivery to cancer cells.

PubMed

Vergaro, Viviana; Lvov, Yuri M; Leporatti, Stefano

2012-09-01

Halloysite is natural aluminosilicate clay with hollow tubular structure which allows loading with low soluble drugs using their saturated solutions in organic solvents. Resveratrol, a polyphenol known for having antioxidant and antineoplastic properties, is loaded inside these clay nanotubes lumens. Release time of 48 h is demonstrated. Spectroscopic and ζ-potential measurements are used to study the drug loading/release and for monitoring the nanotube layer-by-layer (LbL) coating with polyelectrolytes for further release control. Resveratrol-loaded clay nanotubes are added to breast cell cultures for toxicity tests. Halloysite functionalization with LbL polyelectrolyte multilayers remarkably decrease nanotube self-toxicity. MTT measurements performed with a neoplastic cell lines model system (MCF-7) as function of the resveratrol-loaded nanotubes concentration and incubation time indicate that drug-loaded halloysite strongly increase of cytotoxicity leading to cell apoptosis. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Clay Nanoparticles Elicit Long-Term Immune Responses by Forming Biodegradable Depots for Sustained Antigen Stimulation.

PubMed

Chen, Weiyu; Zuo, Huali; Li, Bei; Duan, Chengcheng; Rolfe, Barbara; Zhang, Bing; Mahony, Timothy J; Xu, Zhi Ping

2018-05-01

Nanomaterials have been widely tested as new generation vaccine adjuvants, but few evoke efficient immunoreactions. Clay nanoparticles, for example, layered double hydroxide (LDH) and hectorite (HEC) nanoparticles, have shown their potent adjuvanticity in generating effective and durable immune responses. However, the mechanism by which clay nanoadjuvants stimulate the immune system is not well understood. Here, it is demonstrated that LDH and HEC-antigen complexes form loose agglomerates in culture medium/serum. They also form nodules with loose structures in tissue after subcutaneous injection, where they act as a depot for up to 35 d. More importantly, clay nanoparticles actively and continuously recruit immune cells into the depot for up to one month, and stimulate stronger immune responses than FDA-approved adjuvants, Alum and QuilA. Sustained antigen release is also observed in clay nanoparticle depots, with 50-60% antigen released after 35 d. In contrast, Alum-antigen complexes show minimal antigen release from the depot. Importantly, LDH and HEC are more effective than QuilA and Alum in promoting memory T-cell proliferation. These findings suggest that both clay nanoadjuvants can serve as active vaccine platforms for sustained and potent immune responses. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

In-situ subaqueous capping of mercury-contaminated sediments in a fresh-water aquatic system, Part II-evaluation of sorption materials.

PubMed

Randall, Paul M; Yates, Brian J; Lal, Vivek; Darlington, Ramona; Fimmen, Ryan

2013-08-01

The function and longevity of traditional, passive, isolation caps can be augmented through the use of more chemically active capping materials which have higher sorptive capacities, ideally rendering metals non-bioavailable. In the case of Hg, active caps also mitigate the rate and extent of methylation. This research examined low cost, readily available, capping materials for their ability to sequester Hg and MeHg. Furthermore, selected capping materials were evaluated to inhibit the methylation of Hg in an incubation study as well as the capacity of a selected capping material to inhibit translocation of Hg and MeHg with respect to ebullition-facilitated contaminant transport in a column study. Results indicated that bauxite had a better capacity for mercury sorption than the other test materials. However, bauxite as well as soil capping materials did not decrease methylation to a significant extent. Materials with larger surface areas, higher organic matter and acid volatile sulfide (AVS) content displayed a larger partitioning coefficient. In the incubation experiments, the presence of a carbon source (lactate), electron acceptor (sulfate) and the appropriate strains of SRB provided the necessary conditions for Hg methylation to occur. The column study showed effectiveness in sequestering Hg and MeHg and retarding transport to the overlying water column; however, disturbances to the soil capping material resulting from gas ebullition negated its effectiveness. Published by Elsevier Inc.

Type of closure prevents microbial contamination of cosmetics during consumer use.

PubMed Central

Brannan, D K; Dille, J C

1990-01-01

The dispensing closure used for containers plays an important role in protecting cosmetics from in-use microbial contamination. This hypothesis was tested by aseptically packing unpreserved shampoo and skin lotion into containers with three different closure types which provided various degrees of protection against consumer and environmental microbial insults. Shampoo was packed in containers with slit-cap (n = 25), flip-cap (n = 25), or screw-cap (n = 28) closures. Skin lotion was packed in containers with pump-top (n = 21), flip-cap (n = 18), or screw-cap (n = 21) closures. The products were then used by volunteers under actual in-use conditions for 3 (shampoo) or 2 (skin lotion) weeks. After use, the products were evaluated for microbial contamination by using standard methods for enumeration and identification. The standard screw-cap closure provided only minimal protection against microbial contamination of both the shampoo (29% contamination incidence) and the skin lotion (71%). The slit-cap closure on the shampoo container and the flip-cap closure on the skin lotion container provided slightly enhanced degrees of protection (21 and 39% contamination incidence, respectively). The greatest amount of protection (i.e., lowest contamination incidence) was provided by the flip-cap closure for the shampoo container (0%) and the pump-top closure for the skin lotion container (10%). As a result, closure type plays an important role in protecting poorly preserved products from in-use microbial contamination. Images PMID:2339896

The Common Cryogenic Test Facility for the ATLAS Barrel and End-Cap Toroid Magnets

NASA Astrophysics Data System (ADS)

Delruelle, N.; Haug, F.; Junker, S.; Passardi, G.; Pengo, R.; Pirotte, O.

2004-06-01

The large ATLAS toroidal superconducting magnet made of the Barrel and two End-Caps needs extensive testing at the surface of the individual components prior to their final assembly into the underground cavern of LHC. A cryogenic test facility specifically designed for cooling sequentially the eight coils making the Barrel Toroid (BT) has been fully commissioned and is now ready for final acceptance of these magnets. This facility, originally designed for testing individually the 46 tons BT coils, will be upgraded to allow the acceptance tests of the two End-Caps, each of them having a 160 tons cold mass. The integrated system mainly comprises a 1.2 kW@4.5 K refrigerator, a 10 kW liquid-nitrogen precooler, two cryostats housing liquid helium centrifugal pumps of respectively 80 g/s and 600 g/s nominal flow and specific instrumentation to measure the thermal performances of the magnets. This paper describes the overall facility with particular emphasis to the cryogenic features adopted to match the specific requirements of the magnets in the various operating scenarios.

Improving the Diagnosis of Legionella Pneumonia within a Healthcare System through a Systematic Consultation and Testing Program.

PubMed

Decker, Brooke K; Harris, Patricia L; Muder, Robert R; Hong, Jae H; Singh, Nina; Sonel, Ali F; Clancy, Cornelius J

2016-08-01

Legionella testing is not recommended for all patients with pneumonia, but rather for particular patient subgroups. As a result, the overall incidence of Legionella pneumonia may be underestimated. To determine the incidence of Legionella pneumonia in a veteran population in an endemic area after introduction of a systematic infectious diseases consultation and testing program. In response to a 2011-2012 outbreak, the VA Pittsburgh Healthcare System mandated infectious diseases consultations and testing for Legionella by urine antigen and sputum culture in all patients with pneumonia. Between January 2013 and December 2015, 1,579 cases of pneumonia were identified. The incidence of pneumonia was 788/100,000 veterans per year, including 352/100,000 veterans per year and 436/100,000 veterans per year with community-associated pneumonia (CAP) and health care-associated pneumonia, respectively. Ninety-eight percent of patients with suspected pneumonia were tested for Legionella by at least one method. Legionella accounted for 1% of pneumonia cases (n = 16), including 1.7% (12/706) and 0.6% (4/873) of CAP and health care-associated pneumonia, respectively. The yearly incidences of Legionella pneumonia and Legionella CAP were 7.99 and 5.99/100,000 veterans, respectively. The sensitivities of urine antigen and sputum culture were 81% and 60%, respectively; the specificity of urine antigen was >99.97%. Urine antigen testing and Legionella cultures increased by 65% and 330%, respectively, after introduction of our program. Systematic testing of veterans in an endemic area revealed a higher incidence of Legionella pneumonia and CAP than previously reported. Widespread urine antigen testing was not limited by false positivity.

Advantages of InGaN/GaN multiple quantum wells with two-step grown low temperature GaN cap layers

NASA Astrophysics Data System (ADS)

Zhu, Yadan; Lu, Taiping; Zhou, Xiaorun; Zhao, Guangzhou; Dong, Hailiang; Jia, Zhigang; Liu, Xuguang; Xu, Bingshe

2017-11-01

Two-step grown low temperature GaN cap layers (LT-cap) are employed to improve the optical and structural properties of InGaN/GaN multiple quantum wells (MQWs). The first LT-cap layer is grown in nitrogen atmosphere, while a small hydrogen flow is added to the carrier gas during the growth of the second LT-cap layer. High-resolution X-ray diffraction results indicate that the two-step growth method can improve the interface quality of MQWs. Room temperature photoluminescence (PL) tests show about two-fold enhancement in integrated PL intensity, only 25 meV blue-shift in peak energy and almost unchanged line width. On the basis of temperature-dependent PL characteristics analysis, it is concluded that the first and the second LT-cap layer play a different role during the growth of MQWs. The first LT-cap layer acts as a protective layer, which protects quantum well from serious indium loss and interface roughening resulting from the hydrogen over-etching. The hydrogen gas employed in the second LT-cap layer is in favor of reducing defect density and indium segregation. Consequently, interface/surface and optical properties are improved by adopting the two-step growth method.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pham Minh, Doan, E-mail: doan.phamminh@mines-albi.fr; Nzihou, Ange; Sharrock, Patrick

Highlights: • Carbonated apatite (CAP) could be easily obtained from CaCO{sub 3} and orthophosphates. • Highest CaCO{sub 3} dissolution and apatitic carbonate content were obtained with H{sub 3}PO{sub 4}. • A-B-type CAP was formed. • The synthesized CAP was thermally stable up to 1000 °C. • This CAP showed high biomineralization activity before and after thermal treatment. - Abstract: The one-step synthesis of carbonated hydroxyapatite (CAP) using calcite and different orthophosphates was investigated in a closed batch reactor. Only orthophosphoric acid could lead to the complete decomposition of calcite particles, when the reaction temperature was set at 80 °C. Onmore » the other hand, the reaction time and the dilution of the initial calcite suspension had no significant influence on the formation of the solid products. CAP was formed as the main crystalline calcium phosphate with the carbonate content in the range of 4.2–4.6 wt.%. The thermal decarbonation of the synthesized CAP started at 750 °C but it was only significant at 1000 °C under air atmosphere. This thermal decarbonation was total at 1200 °C or above. All CAP samples and products following thermal treatments were found bioactive in the test using simulated body fluid (SBF) solution.« less

The influence of shale depositional fabric on the kinetics of hydrocarbon generation through control of mineral surface contact area on clay catalysis

NASA Astrophysics Data System (ADS)

Rahman, Habibur M.; Kennedy, Martin; Löhr, Stefan; Dewhurst, David N.; Sherwood, Neil; Yang, Shengyu; Horsfield, Brian

2018-01-01

Accurately assessing the temperature and hence the depth and timing of hydrocarbon generation is a critical step in the characterization of a petroleum system. Clay catalysis is a potentially significant modifier of hydrocarbon generation temperature, but experimental studies of clay catalysis show inconsistent or contradictory results. This study tests the hypothesis that source rock fabric itself is an influence on clay mineral catalysis as it controls the extent to which organic matter and clay minerals are physically associated. Two endmember clay-organic fabrics distinguish the source rocks studied: (1) a particulate fabric where organic matter is present as discrete, >5 μm particles and (2) a nanocomposite fabric in which amorphous organic matter is associated with clay mineral surfaces at sub-micron scale. High-resolution electron imaging and bulk geochemical characterisation confirm that samples of the Miocene Monterey Formation (California) are representative of the nanocomposite source rock endmember, whereas samples from the Permian Stuart Range Formation (South Australia) represent the particulate source rock endmember. Kinetic experiments are performed on paired whole rock and kerogen isolate samples from these two formations using open system, non-isothermal pyrolysis at three different heating rates (0.7, 2 and 5 K/min) to determine the effects of the different shale fabrics on hydrocarbon generation kinetics. Extrapolation to a modelled geological heating rate shows a 20 °C reduction in the onset temperature of hydrocarbon generation in Monterey Formation whole rock samples relative to paired kerogen isolates. This result is consistent with the Monterey Formations's nanocomposite fabric where clay catalysis can proceed because reactive clay minerals are intimately associated with organic matter. By contrast, there is no significant difference in the modelled hydrocarbon generation temperature of paired whole rock and kerogen isolates from the Stuart Range Formation. This is consistent with its particulate fabric, where relatively large, discrete organic particles have limited contact with the mineral matrix and the clay minerals are mainly diagenetic and physically segregated within pores. While heating rate may have a control on mineral matrix effects, this result shows that the extent to which organic matter and clay minerals are physically associated could have a significant effect on the timing of hydrocarbon generation, and is a function of the depositional environment and detrital vs diagenetic origin of clay minerals in source rocks.

Combined Bearing Capacity of Spudcans on a Double Layer Deposit of Strong-Over-Weak Clays

NASA Astrophysics Data System (ADS)

Yin, Qilin; Dong, Sheng

2018-05-01

An extreme sea storm process can lead to a jack-up rig under the combined loading condition of vertical load (V), horizontal load (H), and moment (M) to have stability problems. This paper presents the analysis of combined bearing capacities of a circular spudcan on layered clays with a strong layer overlying a comparatively weaker layer. Numerical models combined with displacement- based load tests, swipe tests, and constant ratio displacement probe tests are adopted to calculate the uniaxial bearing capacities, failure envelopes in combined V-H, V-M planes, and failure envelopes in a combined V-H-M load space, respectively. A parametric study on the effects of vertical load level V, the layer strength ratio s u,t/s u,b, and the hard layer thickness t 1 on the bearing capacities is then performed. Results show that the vertical load level is a key factor that influences the values of H and M and the size of the H-M failure envelope. The existence of the underlying weak clay decreases the bearing capacities in all directions, and the vertical capacity V ult is affected more than the horizontal (H ult) and moment (M ult) capacities based on a single uniform deposit. The influence of the underlying weak clay on H-M failure envelope is mainly shown where H and M are coupled in the same direction. In contrast, little difference is observed when H and M are coupled in opposite directions.

Bioavailability of iron in geophagic earths and clay minerals, and their effect on dietary iron absorption using an in vitro digestion/Caco-2 cell model.

PubMed

Seim, Gretchen L; Ahn, Cedric I; Bodis, Mary S; Luwedde, Flavia; Miller, Dennis D; Hillier, Stephen; Tako, Elad; Glahn, Raymond P; Young, Sera L

2013-08-01

Geophagy, the deliberate consumption of earth, is strongly associated with iron (Fe) deficiency. It has been proposed that geophagy may be practiced as a means to improve Fe status by increasing Fe intakes and, conversely, that geophagy may cause Fe deficiency by inhibiting Fe absorption. We tested these hypotheses by measuring Fe concentration and relative bioavailable Fe content of 12 samples of geophagic earth and 4 samples of pure clay minerals. Further, we assessed the impact of these samples on the bioavailability of Fe from an Fe-rich test meal (cooked white beans, WB). Fe concentrations were measured with inductively coupled plasma atomic emission spectroscopy. Fe bioavailability was determined using an in vitro digestion/Caco-2 cell model in which ferritin formation was used as an index of Fe bioavailability. Geophagic earth and clay mineral samples were evaluated with this model, both alone and in combination with WB (1 : 16 ratio, sample : WB). Median Fe concentration of the geophagic earth was 3485 (IQR 2462, 14 ,571) μg g⁻¹ and mean Fe concentration in the clay minerals was 2791 (±1782) μg g⁻¹. All specimens had Fe concentrations significantly higher (p ≤ 0.005) than the Fe concentration of WB (77 μg g⁻¹). Ferritin formation (i.e. Fe uptake) in cells exposed to geophagic earths and clay minerals was significantly lower than in cells exposed to WB (p ≤ 0.05) and Fe uptake responses of 11 of the 16 samples were not significantly different from the blank, indicating no bioavailable Fe. When samples were combined with WB, 5 of 16 had mean ferritin levels that were significantly lower (p ≤ 0.05, one tail) than the WB alone, indicating that the samples inhibited Fe uptake from the WB. None of the ferritin responses of cells exposed to both WB and earth/clay were significantly higher than WB alone. Thus, although geophagic earths and mineral clays are high in total Fe, very little of this Fe is bioavailable. Further, some geophagic earth and clay mineral samples inhibit Fe absorption from foods. In vivo research is warranted to confirm these observations and to determine if geophagic earth samples can be a source of Fe and/or inhibit Fe absorption.

Bioavailability of iron in geophagic earths and clay minerals, and their effect on dietary iron absorption using an in vitro digestion/Caco-2 cell model

PubMed Central

Seim, Gretchen L.; Ahn, Cedric I.; Bodis, Mary S.; Luwedde, Flavia; Miller, Dennis D.; Hillier, Stephen; Tako, Elad; Glahn, Raymond P.; Young, Sera L.

2014-01-01

Geophagy, the deliberate consumption of earth, is strongly associated with iron (Fe) deficiency. It has been proposed that geophagy may be practiced as a means to improve Fe status by increasing Fe intakes and, conversely, that geophagy may cause Fe deficiency by inhibiting Fe absorption. We tested these hypotheses by measuring Fe concentration and relative bioavailable Fe content of 12 samples of geophagic earth and 4 samples of pure clay minerals. Further, we assessed the impact of these samples on the bioavailability of Fe from an Fe-rich test meal (cooked white beans, WB). Fe concentrations were measured with inductively coupled plasma atomic emission spectroscopy. Fe bioavailability was determined using an in vitro digestion/Caco-2 cell model in which ferritin formation was used as an index of Fe bioavailability. Geophagic earth and clay mineral samples were evaluated with this model, both alone and in combination with WB (1:16 ratio, sample:WB). Median Fe concentration of the geophagic earth was 3485 (IQR 2462, 14571) μg/g and mean Fe concentration in the clay minerals was 2791 (± 1782) μg/g. All specimens had Fe concentrations significantly higher (p ≤ 0.005) than the Fe concentration of WB (77 μg/g). Ferritin formation (i.e. Fe uptake) in cells exposed to geophagic earths and clay minerals was significantly lower than in cells exposed to WB (p ≤ 0.05) and Fe uptake responses of 11 of the 16 samples were not significantly different from the blank, indicating no bioavailable Fe. When samples were combined with WB, 5 of 16 had mean ferritin levels that were significantly lower (p ≤ 0.05, one tail) than the WB alone, indicating that the samples inhibited Fe uptake from the WB. None of the ferritin responses of cells exposed to both WB and earth/clay were significantly higher than WB alone. Thus, although geophagic earths and mineral clays are high in total Fe, very little of this Fe is bioavailable. Further, some geophagic earth and clay mineral samples inhibit Fe absorption from foods. In vivo research is warranted to confirm these observations and to determine if geophagic earth samples can be a source of Fe and/or inhibit Fe absorption. PMID:23787405

PEG-PE/clay composite carriers for doxorubicin: Effect of composite structure on release, cell interaction and cytotoxicity.

PubMed

Kohay, Hagay; Sarisozen, Can; Sawant, Rupa; Jhaveri, Aditi; Torchilin, Vladimir P; Mishael, Yael G

2017-06-01

A novel drug delivery system for doxorubicin (DOX), based on organic-inorganic composites was developed. DOX was incorporated in micelles (M-DOX) of polyethylene glycol-phosphatidylethanolamine (PEG-PE) which in turn were adsorbed by the clay, montmorillonite (MMT). The nano-structures of the PEG-PE/MMT composites of LOW and HIGH polymer loadings were characterized by XRD, TGA, FTIR, size (DLS) and zeta measurements. These measurements suggest that for the LOW composite a single layer of polymer intercalates in the clay platelets and the polymer only partially covers the external surface, while for the HIGH composite two layers of polymer intercalate and a bilayer may form on the external surface. These nanostructures have a direct effect on formulation stability and on the rate of DOX release. The release rate was reversely correlated with the degree of DOX interaction with the clay and followed the sequence: M-DOX>HIGH formulation>LOW formulation>DOX/MMT. Despite the slower release from the HIGH formulation, its cytotoxicity effect on sensitive cells was as high as the "free" DOX. Surprisingly, the LOW formulation, with the slowest release, demonstrated the highest cytotoxicity in the case of Adriamycin (ADR) resistant cells. Confocal microscopy images and association tests provided an insight into the contribution of formulation-cell interactions vs. the contribution of DOX release rate. Internalization of the formulations was suggested as a mechanism that increases DOX efficiency, particularly in the ADR resistant cell line. The employment of organic-inorganic hybrid materials as drug delivery systems, has not reached its full potential, however, its functionality as an efficient tunable release system was demonstrated. DOX PEG-PE/clay formulations were design as an efficient drug delivery system. The main aim was to develop PEG-PE/clay formulations of different structures based on various PEG-PE/clay ratios in order to achieve tunable release rates, to control the external surface characteristics and formulation stability. The formulations showed significantly higher toxicity in comparison to "free" DOX, explained by formulation internalization. For each cell line tested, sensitive and ADR resistant, a different formulation structure was found most efficient. The potential of PEG-PE/clay-DOX formulations to improve DOX administration efficacy was demonstrated and should be further explored and implemented for other cancer drugs and cells. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Clinical evaluation of the COBAS Ampliprep/COBAS TaqMan for HCV RNA quantitation in comparison with the branched-DNA assay.

PubMed

Pittaluga, Fabrizia; Allice, Tiziano; Abate, Maria Lorena; Ciancio, Alessia; Cerutti, Francesco; Varetto, Silvia; Colucci, Giuseppe; Smedile, Antonina; Ghisetti, Valeria

2008-02-01

Diagnosis and monitoring of HCV infection relies on sensitive and accurate HCV RNA detection and quantitation. The performance of the COBAS AmpliPrep/COBAS TaqMan 48 (CAP/CTM) (Roche, Branchburg, NJ), a fully automated, real-time PCR HCV RNA quantitative test was assessed and compared with the branched-DNA (bDNA) assay. Clinical evaluation on 576 specimens obtained from patients with chronic hepatitis C showed a good correlation (r = 0.893) between the two test, but the CAP/CTM scored higher HCV RNA titers than the bDNA across all viral genotypes. The mean bDNA versus CAP/CTM log10 IU/ml differences were -0.49, -0.4, -0.54, -0.26 for genotype 1a, 1b, 2a/2c, 3a, and 4, respectively. These differences reached statistical significance for genotypes 1b, 2a/c, and 3a. The ability of the CAP/CTM to monitor patients undergoing antiviral therapy and correctly identify the weeks 4 and 12 rapid and early virological responses was confirmed. The broader dynamic range of the CAP/CTM compared with the bDNA allowed for a better definition of viral kinetics. In conclusion, the CAP/CTM appears as a reliable and user-friendly assay to monitor HCV viremia during treatment of patients with chronic hepatitis. Its high sensitivity and wide dynamic range may help a better definition of viral load changes during antiviral therapy. (Copyright) 2007 Wiley-Liss, Inc.

Testosterone treatment and the risk of aggressive prostate cancer in men with low testosterone levels.

PubMed

Walsh, Thomas J; Shores, Molly M; Krakauer, Chloe A; Forsberg, Christopher W; Fox, Alexandra E; Moore, Kathryn P; Korpak, Anna; Heckbert, Susan R; Zeliadt, Steven B; Kinsey, Chloe E; Thompson, Mary Lou; Smith, Nicholas L; Matsumoto, Alvin M

2018-01-01

Testosterone treatment of men with low testosterone is common and, although relatively short-term, has raised concern regarding an increased risk of prostate cancer (CaP). We investigated the association between modest-duration testosterone treatment and incident aggressive CaP. Retrospective inception cohort study of male Veterans aged 40 to 89 years with a laboratory-defined low testosterone measurement from 2002 to 2011 and recent prostate specific antigen (PSA) testing; excluding those with recent testosterone treatment, prostate or breast cancer, high PSA or prior prostate biopsy. Histologically-confirmed incident aggressive prostate cancer or any prostate cancer were the primary and secondary outcomes, respectively. Of the 147,593 men included, 58,617 were treated with testosterone. 313 aggressive CaPs were diagnosed, 190 among untreated men (incidence rate (IR) 0.57 per 1000 person years, 95% CI 0.49-0.65) and 123 among treated men (IR 0.58 per 1000 person years; 95% CI 0.48-0.69). After adjusting for age, race, hospitalization during year prior to cohort entry, geography, BMI, medical comorbidities, repeated testosterone and PSA testing, testosterone treatment was not associated with incident aggressive CaP (HR 0.89; 95% CI 0.70-1.13) or any CaP (HR 0.90; 95% CI 0.81-1.01). No association between cumulative testosterone dose or formulation and CaP was observed. Among men with low testosterone levels and normal PSA, testosterone treatment was not associated with an increased risk of aggressive or any CaP. The clinical risks and benefits of testosterone treatment can only be fully addressed by large, longer-term randomized controlled trials.

Leader Positivity and Follower Creativity: An Experimental Analysis

ERIC Educational Resources Information Center

Avey, James B.; Richmond, F. Lynn; Nixon, Don R.

2012-01-01

Using an experimental research design, 191 working adults were randomly assigned to two experimental conditions in order to test a theoretical model linking leader and follower positive psychological capital (PsyCap). Multiple methods were used to gather information from the participants. We found when leader PsyCap was manipulated experimentally,…

Centrifuge modeling of cyclic lateral response of pile-cap systems and seat-type abutments in dry sands

DOT National Transportation Integrated Search

1998-10-02

This report presents the results of slow, cyclic, lateral-loading centrifuge tests performed on models of pile-cap foundation systems and seat-type bridge abutements in dry Neveda sand of 75% relative density to study the lateral response of these sy...

Torque test measurement in segmental bone defects using porous calcium phosphate cement implants.

PubMed

Kroese-Deutman, Henriette C; Wolke, Joop G C; Spauwen, Paul H M; Jansen, John A

2010-10-01

This study was performed to assess the bone healing supporting characteristics of porous calcium phosphate (Ca-P) cement when implanted in a rabbit segmental defect model as well as to determine the reliability of torque testing as a method to verify bone healing. The middiaphyseal radius was chosen as the area to create bilaterally increasing defect sizes (5, 10, and 15 mm), which were either filled with porous Ca-P cement or left open as a control. After 12 weeks of implantation, torque test measurements as well as histological and radiographic evaluation were performed. In two of the open 15 mm control defects, bone bridging was visible at the radiographic and histological evaluation. Bone was observed to be present in all porous Ca-P cement implants (5, 10, and 15 mm defects) after 12 weeks. No significant differences in torque measurements were observed between the 5 and 10 mm filled and open control defects using a t-test. In addition, the mechanical strength of all operated specimens was similar compared with nonoperated bone samples. The torsion data for the 15 mm open defect appeared to be lower compared with the filled 15 mm defect, but no significant difference could be proven. Within the limitation of the study design, porous Ca-P cement implants demonstrated osteoconductive properties and confirmed to be a suitable scaffold material in a weight-bearing situation. Further, the used torque testing method was found to be unreliable for testing the mechanical properties of the healed bone defect.

Clinical Characteristics of Q Fever and Etiology of Community-Acquired Pneumonia in a Tropical Region of Southern Taiwan: A Prospective Observational Study

PubMed Central

Lai, Chung-Hsu; Chang, Lin-Li; Lin, Jiun-Nong; Chen, Wei-Fang; Wei, Yu-Feng; Chiu, Chien-Tung; Wu, Jiun-Ting; Hsu, Chi-Kuei; Chen, Jung-Yueh; Lee, Ho-Sheng; Lin, Hsi-Hsun; Chen, Yen-Hsu

2014-01-01

Background The clinical characteristics of Q fever are poorly identified in the tropics. Fever with pneumonia or hepatitis are the dominant presentations of acute Q fever, which exhibits geographic variability. In southern Taiwan, which is located in a tropical region, the role of Q fever in community-acquired pneumonia (CAP) has never been investigated. Methodology/Principal Findings During the study period, May 2012 to April 2013, 166 cases of adult CAP and 15 cases of acute Q fever were prospectively investigated. Cultures of clinical specimens, urine antigen tests for Streptococcus pneumoniae and Legionella pneumophila, and paired serologic assessments for Mycoplasma pneumoniae, Chlamydophila pneumoniae, and Q fever (Coxiella burnetii) were used for identifying pathogens associated with CAP. From April 2004 to April 2013 (the pre-study period), 122 cases of acute Q fever were also included retrospectively for analysis. The geographic distribution of Q fever and CAP cases was similar. Q fever cases were identified in warmer seasons and younger ages than CAP. Based on multivariate analysis, male gender, chills, thrombocytopenia, and elevated liver enzymes were independent characteristics associated with Q fever. In patients with Q fever, 95% and 13.5% of cases presented with hepatitis and pneumonia, respectively. Twelve (7.2%) cases of CAP were seropositive for C. burnetii antibodies, but none of them had acute Q fever. Among CAP cases, 22.9% had a CURB-65 score ≧2, and 45.8% had identifiable pathogens. Haemophilus parainfluenzae (14.5%), S. pneumoniae (6.6%), Pseudomonas aeruginosa (4.8%), and Klebsiella pneumoniae (3.0%) were the most common pathogens identified by cultures or urine antigen tests. Moreover, M. pneumoniae, C. pneumoniae, and co-infection with 2 pathogens accounted for 9.0%, 7.8%, and 1.8%, respectively. Conclusions In southern Taiwan, Q fever is an endemic disease with hepatitis as the major presentation and is not a common etiology of CAP. PMID:25033402

Resilient modulus testing of materials from MN/Road : phase 1

DOT National Transportation Integrated Search

1996-09-01

The U.S. Army Cold Regions Research and Engineering Laboratory (CRREL) conducted resilient modulus tests on materials from the MN/ROAD test site for the Minnesota Department of Transportation. Materials tested included samples of the lean clay subgra...

Removal of ibuprofen, naproxen and carbamazepine in aqueous solution onto natural clay: equilibrium, kinetics, and thermodynamic study

NASA Astrophysics Data System (ADS)

Khazri, Hassen; Ghorbel-Abid, Ibtissem; Kalfat, Rafik; Trabelsi-Ayadi, Malika

2017-10-01

This study aimed to describe the adsorption of three pharmaceuticals compounds (ibuprofen, naproxen and carbamazepine) onto natural clay on the basis of equilibrium parameters such as a function of time, effect of pH, varying of the concentration and the temperature. Adsorption kinetic data were modeled using the Lagergren's first-order and the pseudo-second-order kinetic equations. The kinetic results of adsorption are described better using the pseudo-second order model. The isotherm results were tested in the Langmuir, Freundlich and Dubinin-Radushkevich models. The thermodynamic parameters obtained indicate that the adsorption of pharmaceuticals on the clay is a spontaneous and endothermic process.

Numerical Analysis of Helical Pile-Soil Interaction under Compressive Loads

NASA Astrophysics Data System (ADS)

Polishchuk, A. I.; Maksimov, F. A.

2017-11-01

The results of the field tests of full-scale steel helical piles in clay soils intended for prefabricated temporary buildings foundations are presented in this article. The finite element modeling was used for the evaluation of stress distribution of the clay soil around helical piles. An approach of modeling of the screw-pile geometry has been proposed through the Finite Element Analysis. Steel helical piles with a length of 2.0 m, shaft diameter of 0.108 m and a blade diameter of 0.3 m were used in the experiments. The experiments have shown the efficiency of double-bladed helical piles in the clay soils compared to single-bladed piles. It has been experimentally established that the introduction of the second blade into the pile shaft provides an increase of the bearing capacity in clay soil up to 30% compared to a single-bladed helical pile with similar geometrical dimensions. The numerical results are compared with the measurements obtained by a large scale test and the bearing capacity has been estimated. It has been found that the model results fit the field results. For a double-bladed helical pile it was revealed that shear stresses upon pile loading are formed along the lateral surface forming a cylindrical failure surface.

The atypical pneumonias: clinical diagnosis and importance.

PubMed

Cunha, B A

2006-05-01

The most common atypical pneumonias are caused by three zoonotic pathogens, Chlamydia psittaci (psittacosis), Francisella tularensis (tularemia), and Coxiella burnetii (Q fever), and three nonzoonotic pathogens, Chlamydia pneumoniae, Mycoplasma pneumoniae, and Legionella. These atypical agents, unlike the typical pathogens, often cause extrapulmonary manifestations. Atypical CAPs are systemic infectious diseases with a pulmonary component and may be differentiated clinically from typical CAPs by the pattern of extrapulmonary organ involvement which is characteristic for each atypical CAP. Zoonotic pneumonias may be eliminated from diagnostic consideration with a negative contact history. The commonest clinical problem is to differentiate legionnaire's disease from typical CAP as well as from C. pneumoniae or M. pneumonia infection. Legionella is the most important atypical pathogen in terms of severity. It may be clinically differentiated from typical CAP and other atypical pathogens by the use of a weighted point system of syndromic diagnosis based on the characteristic pattern of extrapulmonary features. Because legionnaire's disease often presents as severe CAP, a presumptive diagnosis of Legionella should prompt specific testing and empirical anti-Legionella therapy such as the Winthrop-University Hospital Infectious Disease Division's weighted point score system. Most atypical pathogens are difficult or dangerous to isolate and a definitive laboratory diagnosis is usually based on indirect, i.e., direct flourescent antibody (DFA), indirect flourescent antibody (IFA). Atypical CAP is virtually always monomicrobial; increased IFA IgG tests indicate past exposure and not concurrent infection. Anti-Legionella antibiotics include macrolides, doxycycline, rifampin, quinolones, and telithromycin. The drugs with the highest level of anti-Legionella activity are quinolones and telithromycin. Therapy is usually continued for 2 weeks if potent anti-Legionella drugs are used. In adults, M. pneumoniae and C. pneumoniae may exacerbate or cause asthma. The importance of the atypical pneumonias is not related to their frequency (approximately 15% of CAPs), but to difficulties in their diagnosis, and their nonresponsiveness to beta-lactam therapy. Because of the potential role of C. pneumoniae in coronary artery disease and multiple sclerosis (MS), and the role of M. pneumoniae and C. pneumoniae in causing or exacerbating asthma, atypical CAPs also have public health importance.

A pilot study analyzing PSA, serum testosterone, lipid profile, body mass index and race in a small sample of patients with and without carcinoma of the prostate.

PubMed

Mydlo, J H; Tieng, N L; Volpe, M A; Chaiken, R; Kral, J G

2001-01-01

Androgens, diet, race and obesity are thought to play some roles in the pathogenesis of prostate cancer. We wanted to evaluate if there were any inter-relationships between prostate specific antigen (PSA), serum testosterone, serum cholesterol, HDL, triglycerides, body mass index (BMI) and race, in older patients with and without prostate cancer (CaP). We evaluated 308 patients referred to urologists in private practice offices and clinics with and without prostate cancer with regard to race, serum PSA, age, serum testosterone, full lipid profile, height and weight, and stage of cancer. We used multivariate analysis, Fisher's exact test and t-tests as well as logistic regression analysis. Data was analyzed using SPSS computer software, and P-values<0.05 were considered statistically significant. Significantly higher levels of serum testosterone were found in black men with CaP than black men without CaP (526+/-28 vs 404+/-19, respectively.) We also found significantly higher levels of serum testosterone in white men with CaP than white men without CaP (409+/-20 vs 302+/-14, respectively, P<0.05). HDL was higher in black men than white men, and triglycerides were higher in white men than black men. Cholesterol was similar across all groups, but BMI was highest in white men with CaP. We also found a significant association between BMI and pathological stage of prostate cancer patients among both black and white men (P<0.05). Our study demonstrated that black men who developed CaP had higher serum testosterone levels, on average, than white men who developed CaP. Furthermore, BMI was highest in white men developing CaP compared to black men, but we found a significant association between pathological stage and BMI in both black and white patients. Although it is controversial whether obesity is considered to be a risk factor for prostate cancer, this small pilot study suggests that BMI may play a role in the progression of the disease once it is established.Prostate Cancer and Prostatic Diseases (2001) 4, 101-105

Moving granular-bed filter development program, Option III: Development of moving granular-bed filter technology for multi-contaminant control. Task 14: Test plan; Topical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haas, J.C.; Olivo, C.A.; Wilson, K.B.

1994-04-01

An experimental test plan has been prepared for DOE/METC review and approval to develop a filter media suitable for multi-contaminant control in granular-bed filter (GBF) applications. The plan includes identification, development, and demonstration of methods for enhanced media morphology, chemical reactivity, and mechanical strength. The test plan includes media preparation methods, physical and chemical characterization methods for fresh and reacted media, media evaluation criteria, details of test and analytical equipment, and test matrix of the proposed media testing. A filter media composed of agglomerated limestone and clay was determined to be the best candidate for multi-contaminate control in GBF operation.more » The combined limestone/clay agglomerate has the potential to remove sulfur and alkali species, in addition to particulate, and possibly halogens and trace heavy metals from coal process streams.« less

Multifunctional nanocarrier based on clay nanotubes for efficient intracellular siRNA delivery and gene silencing.

PubMed

Wu, Hui; Shi, Yinfeng; Huang, Chusen; Zhang, Yang; Wu, Jiahui; Shen, Hebai; Jia, Nengqin

2014-04-01

RNA interference-mediated gene silencing relating to disease has recently emerged as a powerful method in gene therapy. Despite the promises, effective transport of siRNA with minimal side effects remains a challenge. Halloysites are cheap and naturally available aluminosilicate clay nanotubes with high mechanical strength and biocompatibility. In this study, a novel multifunctional nanocarrier based on functionalized halloysite nanotubes (f-HNTs) has been developed via electrostatic layer-by-layer assembling approach for loading and intracellular delivery of therapeutic antisurvivin siRNA and simultaneously tracking their intracellular transport, in which PEI-modified HNTs are used as gene vector, antisurvivin siRNA as gene therapeutic agent, and mercaptoacetic acid-capped CdSe quantum dots as fluorescent labeling probes. The successful assembly of the f-HNTs-siRNA complexes was systematically characterized by transmission electron microscopy (TEM), UV-visible spectrophotometry, Zeta potential measurement, fluorescence spectrophotometry, and electrochemical impedance spectroscopy. Confocal microscopy, biological TEM, and flow cytometry studies revealed that the complexes enabled the efficient intracellular delivery of siRNA for cell-specific gene silencing. MTT assays exhibited that the complexes can enhance antitumor activity. Furthermore, Western blot analysis showed that f-HNTs-mediated siRNA delivery effectively knocked down gene expression of survivin and thereby decreased the levels of target proteins of PANC-1 cells. Therefore, this study suggested that the synthesized f-HNTs were a new effective drug delivery system for potential application in cancer gene therapy.

Combined natural gamma ray spectral/litho-density measurements applied to complex lithologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quirein, J.A.; Gardner, J.S.; Watson, J.T.

1982-09-01

Well log data has long been used to provide lithological descriptions of complex formations. Historically, most of the approaches used have been restrictive because they assumed fixed, known, and distinct lithologies for specified zones. The approach described in this paper attempts to alleviate this restriction by estimating the ''probability of a model'' for the models suggested as most likely by the reservoir geology. Lithological variables are simultaneously estimated from response equations for each model and combined in accordance with the probability of each respective model. The initial application of this approach has been the estimation of calcite, quartz, and dolomitemore » in the presence of clays, feldspars, anhydrite, or salt. Estimations were made by using natural gamma ray spectra, photoelectric effect, bulk density, and neutron porosity information. For each model, response equations and parameter selections are obtained from the thorium vs potassium crossplot and the apparent matrix density vs apparent volumetric photoelectric cross section crossplot. The thorium and potassium response equations are used to estimate the volumes of clay and feldspar. The apparent matrix density and volumetric cross section response equations can then be corrected for the presence of clay and feldspar. A test ensures that the clay correction lies within the limits for the assumed lithology model. Results are presented for varying lithologies. For one test well, 6,000 feet were processed in a single pass, without zoning and without adjusting more than one parameter pick. The program recognized sand, limestone, dolomite, clay, feldspar, anhydrite, and salt without analyst intervention.« less

The Influence of Syndepositional Macropores on the Hydraulic Integrity of Thick Alluvial Clay Aquitards

NASA Astrophysics Data System (ADS)

Timms, Wendy A.; Acworth, R. Ian; Crane, Richard A.; Arns, Christoph H.; Arns, Ji-Youn; McGeeney, Dayna E.; Rau, Gabriel C.; Cuthbert, Mark O.

2018-04-01

Clay-rich deposits are commonly assumed to be aquitards which act as natural hydraulic barriers due to their low hydraulic connectivity. Postdepositional weathering processes are known to increase the permeability of aquitards in the near surface but not impact on deeper parts of relatively thick formations. However, syndepositional processes affecting the hydraulic properties of aquitards have previously received little attention in the literature. Here, we analyze a 31 m deep sediment core recovered from an inland clay-rich sedimentary sequence using a combination of techniques including particle size distribution and microscopy, centrifuge dye tracer testing and micro X-ray CT imaging. Subaerial deposition of soils within these fine grained alluvial deposits has led to the preservation of considerable macropores (root channels or animal burrows). Connected pores and macropores thus account for vertical hydraulic conductivity (K) of 4.2×10-9 m/s (geometric mean of 13 samples) throughout the thick aquitard, compared to a matrix K that is likely <10-10 m/s, the minimum K value that was measured. Our testing demonstrates that such syndepositional features may compromise the hydraulic integrity of what otherwise appears to have the characteristics of a much lower permeability aquitard. Heterogeneity within a clay-rich matrix could also enhance vertical connectivity, as indicated by digital analysis of pore morphology in CT images. We highlight that the paleo-environment under which the sediment was deposited must be considered when aquitards are investigated as potential natural hydraulic barriers and illustrate the value of combining multiple investigation techniques for characterizing clay-rich deposits.

Coextrusion-Based 3D Plotting of Ceramic Pastes for Porous Calcium Phosphate Scaffolds Comprised of Hollow Filaments.

PubMed

Jo, In-Hwan; Koh, Young-Hag; Kim, Hyoun-Ee

2018-05-29

This paper demonstrates the utility of coextrusion-based 3D plotting of ceramic pastes (CoEx-3DP) as a new type of additive manufacturing (AM) technique, which can produce porous calcium phosphate (CaP) ceramic scaffolds comprised of hollow CaP filaments. In this technique, green filaments with a controlled core/shell structure can be produced by coextruding an initial feedrod, comprised of the carbon black (CB) core and CaP shell, through a fine nozzle in an acetone bath and then deposited in a controlled manner according to predetermined paths. In addition, channels in CaP filaments can be created through the removal of the CB cores during heat-treatment. Produced CaP scaffolds had two different types of pores with well-defined geometries: three-dimensionally interconnected pores (~360 × 230 μm² in sizes) and channels (>100 μm in diameter) in hollow CaP filaments. The porous scaffolds showed high compressive strengths of ~12.3 ± 2.2 MPa at a high porosity of ~73 vol % when compressed parallel to the direction of the hollow CaP filaments. In addition, the mechanical properties of porous CaP scaffolds could be tailored by adjusting their porosity, for example, compressive strengths of 4.8 ± 1.1 MPa at a porosity of ~82 vol %. The porous CaP scaffold showed good biocompatibility, which was assessed by in vitro cell tests, where several the cells adhered to and spread actively with the outer and inner surfaces of the hollow CaP filaments.

Effects of circumferential ankle pressure on ankle proprioception, stiffness, and postural stability: a preliminary investigation.

PubMed

You, Sung H; Granata, Kevin P; Bunker, Linda K

2004-08-01

Cross-sectional repeated-measures design. Determine the effects of circumferential ankle pressure (CAP) intervention on proprioceptive acuity, ankle stiffness, and postural stability. The application of CAP using braces, taping, and adaptive shoes or military boots is widely used to address chronic ankle instability (CAI). An underlying assumption is that the CAP intervention might improve ankle stability through increased proprioceptive acuity and stiffness in the ankle. METHOD AND MEASURES: A convenience sample of 10 subjects was recruited from the local university community and categorized according to proprioceptive acuity (high, low) and ankle stability (normal, CAI). Proprioceptive acuity was measured when blindfolded subjects were asked to accurately reproduce a self-selected target ankle position before and after the application of CAP. Proprioceptive acuity was determined in 5 different ankle joint position sense tests: neutral, inversion, eversion, plantar flexion, and dorsiflexion. Joint position angles were recorded electromechanically using a potentiometer. Passive ankle stiffness was computed from the ratio of applied static moment versus angular displacement. Active ankle stiffness was determined from biomechanical analyses of ankle motion following a mediolateral perturbation. Postural stability was quantified from the center of pressure displacement in the mediolateral and the anteroposterior directions in unipedal stance. All measurements were recorded with and without CAP applied by a pediatric blood pressure cuff. Data were analyzed using a separate mixed-model analysis of variance (ANOVA) for each dependent variable. Post hoc comparison using Tukey's honestly significant difference (HSD) test was performed if significant interactions were obtained. Significance level was set at P<.05 for all analyses. Significant group (high versus low proprioceptive acuity) x CAP interactions were identified for postural stability. Passive ankle stiffness was not increased by an application of CAP. Active ankle stiffness was significantly different between the high and low proprioceptive acuity groups and was not affected by an application of CAP. Significant group (normal versus CAI) x CAP interactions were observed for mediolateral center-of-pressure displacement with a main effect of group on neutral joint position sense. Application of CAP increased proprioceptive acuity and demonstrated trends toward increased active stiffness in the ankle, hence improved postural stability. The effects tend to be limited to individuals with low proprioceptive acuity.

Applications of three-dimensional modeling in electromagnetic exploration

NASA Astrophysics Data System (ADS)

Pellerin, Louise Donna

Numerical modeling is used in geophysical exploration to understand physical mechanisms of a geophysical method, compare different exploration techniques, and interpret field data. Exploring the physics of a geophysical response enhances the geophysicist's insight, resulting in better survey design and interpretation. Comparing exploration methods numerically can eliminate the use of a technique that cannot resolve the exploration target. Interpreting field data to determine the structure of the earth is the ultimate goal of the exploration geophysicist. Applications of three-dimensional (3-D) electromagnetic (EM) modeling in mining, geothermal and environmental exploration demonstrate the importance of numerical modeling as a geophysical tool. Detection of a confined, conductive target with a vertical electric source (VES) can be an effective technique if properly used. The vertical magnetic field response is due solely to multi-dimensional structures, and current channeling is the dominant mechanism. A VES is deployed in a bore hole, hence the orientation of the hole is critical to the response. A deviation of more than a degree from the vertical can result in a host response that overwhelms the target response. Only the in-phase response at low frequencies can be corrected to a purely vertical response. The geothermal system studied consists of a near-surface clay cap and a deep reservoir. The magnetotelluric (MT), controlled-source audio magnetotelluric (CSAMT), long-offset time-domain electromagnetic (LOTEM) and central-loop transient electromagnetic (TEM) methods are appraised for their ability to detect the reservoir and delineate the cap. The reservoir anomaly is supported by boundary charges and therefore is detectable only with deep sounding electric field measurement MT and LOTEM. The cap is easily delineated with all techniques. For interpretation I developed an approximate 3-D inversion that refines a 1-D interpretation by removing lateral distortions. An iterative inverse procedure invokes EM reciprocity while operating on a localized portion of the survey area thereby greatly reducing the computational requirements. The scheme is illustrated with three synthetic data sets representative of problems in environmental geophysics.

Oriented clay nanopaper from biobased components--mechanisms for superior fire protection properties.

PubMed

Carosio, F; Kochumalayil, J; Cuttica, F; Camino, G; Berglund, L

2015-03-18

The toxicity of the most efficient fire retardant additives is a major problem for polymeric materials. Cellulose nanofiber (CNF)/clay nanocomposites, with unique brick-and-mortar structure and prepared by simple filtration, are characterized from the morphological point of view by scanning electron microscopy and X-ray diffraction. These nanocomposites have superior fire protection properties to other clay nanocomposites and fiber composites. The corresponding mechanisms are evaluated in terms of flammability (reaction to a flame) and cone calorimetry (exposure to heat flux). These two tests provide a wide spectrum characterization of fire protection properties in CNF/montmorrilonite (MTM) materials. The morphology of the collected residues after flammability testing is investigated. In addition, thermal and thermo-oxidative stability are evaluated by thermogravimetric analyses performed in inert (nitrogen) and oxidative (air) atmospheres. Physical and chemical mechanisms are identified and related to the unique nanostructure and its low thermal conductivity, high gas barrier properties and CNF/MTM interactions for char formation.

Potentialité d'utilisation d'argiles marocaines de Jbel Kharrou dans l'industrie céramique

NASA Astrophysics Data System (ADS)

El Yakoubi, Nadia; Aberkan, M'hamed; Ouadia, Mohamed

2006-08-01

The Ordovician clays of Jbel Kharrou (Rehamna, Morocco) have been studied for their use in ceramic industry. The realised studies were carried out on two samples B1 and B2, the most representative, taken from a clay dominated formation that outcrops 25 km east of the Skhour Rehamna city. The chemical analyses, mineralogical studies and advanced technological tests undertaken on the two samples indicate that these clays can be considered as non-refractory material, so they can be used to the manufacturing of ceramic products: soil and wall tiles, sanitary, pottery, etc. The tested briquettes, cooked at 1040 °C, remain flat, without deformation or defects; they are of cream white dye. These briquettes show a high mechanical resistance to the flexion, the loss in weight remains tolerable with cooking, lightly elevated (12% ); it can be corrected by the addition of a grease-remover. To cite this article: N. El Yakoubi et al., C. R. Geoscience 338 (2006).

Redox Control and Hydrogen Production in Sediment Caps Using Carbon Cloth Electrodes

PubMed Central

Sun, Mei; Yan, Fei; Zhang, Ruiling; Reible, Danny D.; Lowry, Gregory V.; Gregory, Kelvin B.

2010-01-01

Sediment caps that degrade contaminants can improve their ability to contain contaminants relative to sand and sorbent-amended caps, but few methods to enhance contaminant degradation in sediment caps are available. The objective of this study was to determine if, carbon electrodes emplaced within a sediment cap at poised potential could create a redox gradient and provide electron donor for the potential degradation of contaminants. In a simulated sediment cap overlying sediment from the Anacostia River (Washington, DC), electrochemically induced redox gradients were developed within 3 days and maintained over the period of the test (~100 days). Hydrogen and oxygen were produced by water electrolysis at the electrode surfaces and may serve as electron donor and acceptor for contaminant degradation. Electrochemical and geochemical factors that may influence hydrogen production were studied. Hydrogen production displayed zero order kinetics with ~75% coulombic efficiency and rates were proportional to the applied potential between 2.5V to 5V and not greatly affected by pH. Hydrogen production was promoted by increasing ionic strength and in the presence of natural organic matter. Graphite electrode-stimulated degradation of tetrachlorobenzene in a batch reactor was dependent on applied voltage and production of hydrogen to a concentration above the threshold for biological dechlorination. These findings suggest that electrochemical reactive capping can potentially be used to create “reactive” sediments caps capable of promoting chemical or biological transformations of contaminants within the cap. PMID:20879761

Response of Buried Vertically Oriented Cylinders to Dynamic Loading,

DTIC Science & Technology

1980-06-01

BALSARA • , . / ,, _,-, -. 1i S ,LESPONSE OF BURIED VERTICALLY 9RIENTED CYLINDERS 𔃺 .-TO DINAMIC LOADING_ 9AYLE E. LRTOrwW&-N JIIMY P./BALSARA Nk...1.7, 2,8, and 4.0 inches). The end caps for the cylinders consisted of a steel shell filled with high- strength concrete; however, the end caps were...not designed to be test articles. The average concrete compressive strength of the cylinders on test day was 44.0 MPa (6,380 psi). The three DEOT

Legionella pneumophila serogroup 3 infection: importance of serology.

PubMed

Khanna, N; Meikle, A; Gillespie, L; Edwards, G; Lindsay, D

2012-08-01

We present a case of Legionella pneumophila serogroup 3 (LP3) infection in a patient with severe community-acquired pneumonia (CAP). The diagnosis was complicated by an initial equivocal L. pneumophila urinary antigen test, followed by two negative samples. LP3 was cultured from a sputum sample and the diagnosis was confirmed by serology 15 days into the admission. This case highlights the importance of considering non-LP1 serogroups as causes of CAP and the role of serological testing in diagnosis.

Hillslope Chromatography in Savannas

NASA Astrophysics Data System (ADS)

Hartshorn, A.; Khomo, L.; Chadwick, O.; Rogers, K.; Kurtz, A.; Heimsath, A.

2005-12-01

In semiarid ecosystems, vegetation patterns are controlled in part by soil water availability. Along hillslopes in Kruger National Park, South Africa, water availability is strongly dependent on soil texture and textural differences with depth, which are a function of landscape position (convergent or divergent crests, midslopes, and footslopes) and parent material. We are studying weathering and landscape development on the western side of the park, which is underlain by granitic gneisses. Hillslopes in the park are often described as catenas, where rainfall catalyzes chemical weathering and drives the downslope transport of clays and weathering products, forming a predictable sequence of soil types. Sandy crest soils grade to midslope soils where sandy surface horizons overlie clayey subsurface horizons; footslopes generally have higher volumetric clay contents. The boundary between the sandy and clayey soils is of ecological significance because this is the location where run-on from upslope landscape positions is diverted to the surface, initiating overland flow and reducing infiltration. In a geochemical sense these hillslopes can be thought of as chromatographic columns that accentuate differential solute mobility along the long (~1-2 km) potential flowpaths. We use the compound topographic index (a terrain attribute that indexes soil wetness by dividing the upslope contributing area by the slope) to predict the redistribution of clays across these semiarid hillslopes and hope to demonstrate that landscape positions occupying comparable plan and profile curvatures contain clay and organic carbon in proportion to contributing area. Thus far, we have derived contributing area values for 40 soil pits using LiDAR-based digital elevation models and then tested how well contributing area and other terrain attributes predicted clay and carbon content for 218 horizons at these 40 locations. Depth-weighted soil clay ranged from 3 to 25% and total soil carbon ranged from 0.1 to 2.1%. Our preliminary results suggest that greater contributing area only produces greater soil clay content up to a threshold clay content, after which clay illuviation and in situ clay production slows following the diversion of water to the surface.

A remediation performance model for enhanced metabolic reductive dechlorination of chloroethenes in fractured clay till

NASA Astrophysics Data System (ADS)

Manoli, Gabriele; Chambon, Julie C.; Bjerg, Poul L.; Scheutz, Charlotte; Binning, Philip J.; Broholm, Mette M.

2012-04-01

A numerical model of metabolic reductive dechlorination is used to describe the performance of enhanced bioremediation in fractured clay till. The model is developed to simulate field observations of a full scale bioremediation scheme in a fractured clay till and thereby to assess remediation efficiency and timeframe. A relatively simple approach is used to link the fermentation of the electron donor soybean oil to the sequential dechlorination of trichloroethene (TCE) while considering redox conditions and the heterogeneous clay till system (clay till matrix, fractures and sand stringers). The model is tested on lab batch experiments and applied to describe sediment core samples from a TCE-contaminated site. Model simulations compare favorably to field observations and demonstrate that dechlorination may be limited to narrow bioactive zones in the clay matrix around fractures and sand stringers. Field scale simulations show that the injected donor is expected to be depleted after 5 years, and that without donor re-injection contaminant rebound will occur in the high permeability zones and the mass removal will stall at 18%. Long remediation timeframes, if dechlorination is limited to narrow bioactive zones, and the need for additional donor injections to maintain dechlorination activity may limit the efficiency of ERD in low-permeability media. Future work should address the dynamics of the bioactive zones, which is essential to understand for predictions of long term mass removal.

KSC-03PD-2981

NASA Technical Reports Server (NTRS)

2003-01-01

KENNEDY SPACE CENTER, FLA. In the Orbiter Processing Facility, packing material is placed over the nose cap that was removed from Atlantis. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non- destructive testing such as CAT scan and thermography.

KSC-03PD-2980

NASA Technical Reports Server (NTRS)

2003-01-01

KENNEDY SPACE CENTER, FLA. In the Orbiter Processing Facility, workers remove the overhead crane from the nose cap that was removed from Atlantis. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

KSC-03PD-2978

NASA Technical Reports Server (NTRS)

2003-01-01

KENNEDY SPACE CENTER, FLA. In the Orbiter Processing Facility, the nose cap from Atlantis is lowered toward a shipping pallet. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

KSC-03PD-2979

NASA Technical Reports Server (NTRS)

2003-01-01

KENNEDY SPACE CENTER, FLA. In the Orbiter Processing Facility, the nose cap from Atlantis is secured on a shipping pallet. The reinforced carbon-carbon (RCC) nose cap is being sent to the original manufacturing company, Vought in Ft. Worth, Texas, a subsidiary of Lockheed Martin, to undergo non-destructive testing such as CAT scan and thermography.

30 CFR 20.0 - Compliance with the requirements necessary for obtaining approval.

Code of Federal Regulations, 2011 CFR

2011-07-01

... LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MINE LAMPS OTHER THAN STANDARD CAP LAMPS § 20.0 Compliance with the requirements necessary for obtaining approval. To receive approval of MSHA for any electric mine lamps other than standard cap lamps a manufacturer must comply with the...

30 CFR 20.0 - Compliance with the requirements necessary for obtaining approval.

Code of Federal Regulations, 2013 CFR

2013-07-01

... LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MINE LAMPS OTHER THAN STANDARD CAP LAMPS § 20.0 Compliance with the requirements necessary for obtaining approval. To receive approval of MSHA for any electric mine lamps other than standard cap lamps a manufacturer must comply with the...

30 CFR 20.0 - Compliance with the requirements necessary for obtaining approval.

Code of Federal Regulations, 2012 CFR

2012-07-01

... LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MINE LAMPS OTHER THAN STANDARD CAP LAMPS § 20.0 Compliance with the requirements necessary for obtaining approval. To receive approval of MSHA for any electric mine lamps other than standard cap lamps a manufacturer must comply with the...

30 CFR 20.0 - Compliance with the requirements necessary for obtaining approval.

Code of Federal Regulations, 2014 CFR

2014-07-01

... LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MINE LAMPS OTHER THAN STANDARD CAP LAMPS § 20.0 Compliance with the requirements necessary for obtaining approval. To receive approval of MSHA for any electric mine lamps other than standard cap lamps a manufacturer must comply with the...

46 CFR 118.410 - Fixed gas fire extinguishing systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... piping must be capped within the space protected at the first joint between the nozzles and the storage... and the first nozzle in the system must be capped and pneumatically tested for a period of 10 minutes... protect the piping from overpressurization. (3) Nozzles must be approved by the Commandant. (4) When...

46 CFR 118.410 - Fixed gas fire extinguishing systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... piping must be capped within the space protected at the first joint between the nozzles and the storage... and the first nozzle in the system must be capped and pneumatically tested for a period of 10 minutes... protect the piping from overpressurization. (3) Nozzles must be approved by the Commandant. (4) When...

46 CFR 118.410 - Fixed gas fire extinguishing systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... piping must be capped within the space protected at the first joint between the nozzles and the storage... and the first nozzle in the system must be capped and pneumatically tested for a period of 10 minutes... protect the piping from overpressurization. (3) Nozzles must be approved by the Commandant. (4) When...

Multi-strategy coevolving aging particle optimization.

PubMed

Iacca, Giovanni; Caraffini, Fabio; Neri, Ferrante

2014-02-01

We propose Multi-Strategy Coevolving Aging Particles (MS-CAP), a novel population-based algorithm for black-box optimization. In a memetic fashion, MS-CAP combines two components with complementary algorithm logics. In the first stage, each particle is perturbed independently along each dimension with a progressively shrinking (decaying) radius, and attracted towards the current best solution with an increasing force. In the second phase, the particles are mutated and recombined according to a multi-strategy approach in the fashion of the ensemble of mutation strategies in Differential Evolution. The proposed algorithm is tested, at different dimensionalities, on two complete black-box optimization benchmarks proposed at the Congress on Evolutionary Computation 2010 and 2013. To demonstrate the applicability of the approach, we also test MS-CAP to train a Feedforward Neural Network modeling the kinematics of an 8-link robot manipulator. The numerical results show that MS-CAP, for the setting considered in this study, tends to outperform the state-of-the-art optimization algorithms on a large set of problems, thus resulting in a robust and versatile optimizer.

Use of a clay modeling task to reduce chocolate craving.

PubMed

Andrade, Jackie; Pears, Sally; May, Jon; Kavanagh, David J

2012-06-01

Elaborated Intrusion theory (EI theory; Kavanagh, Andrade, & May, 2005) posits two main cognitive components in craving: associative processes that lead to intrusive thoughts about the craved substance or activity, and elaborative processes supporting mental imagery of the substance or activity. We used a novel visuospatial task to test the hypothesis that visual imagery plays a key role in craving. Experiment 1 showed that spending 10 min constructing shapes from modeling clay (plasticine) reduced participants' craving for chocolate compared with spending 10 min 'letting your mind wander'. Increasing the load on verbal working memory using a mental arithmetic task (counting backwards by threes) did not reduce craving further. Experiment 2 compared effects on craving of a simpler verbal task (counting by ones) and clay modeling. Clay modeling reduced overall craving strength and strength of craving imagery, and reduced the frequency of thoughts about chocolate. The results are consistent with EI theory, showing that craving is reduced by loading the visuospatial sketchpad of working memory but not by loading the phonological loop. Clay modeling might be a useful self-help tool to help manage craving for chocolate, snacks and other foods. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Activity Profile of Young Tennis Athletes Playing on Clay and Hard Courts: Preliminary Data.

PubMed

Adriano Pereira, Lucas; Freitas, Victor; Arruda Moura, Felipe; Saldanha Aoki, Marcelo; Loturco, Irineu; Yuzo Nakamura, Fábio

2016-04-01

The aim of this study was to compare the kinematic characteristics of tennis matches between red clay and hard courts in young tennis players. Eight young tennis players performed two tennis matches on different court surfaces. The match activities were monitored using GPS units. The distance covered in different velocity ranges and the number of accelerations were analyzed. The paired t test and inference based on magnitudes were used to compare the match physical performance between groups. The total distance (24% of difference), high-intensity running distance (15 - 18 km/h) (30% of difference), the number of high-intensity activities (44% of difference), the body load (1% of difference), and accelerations >1.5 g (1.5-2 g and >2 g 7.8 and 8.1 % of difference, respectively) were significantly greater in clay court than hard court matches ( p < 0.05). Matches played on the red clay court required players to cover more total and high-intensity running distances and engage in more high-intensity activities than the matches played on the hard court. Finally, on the clay court the body load and the number of accelerations performed (>1.5 g) were possibly higher than on the hard court.

Statistical analysis of the factors that influenced the mechanical properties improvement of cassava starch films

NASA Astrophysics Data System (ADS)

Monteiro, Mayra; Oliveira, Victor; Santos, Francisco; Barros Neto, Eduardo; Silva, Karyn; Silva, Rayane; Henrique, João; Chibério, Abimaelle

2017-08-01

In order to obtain cassava starch films with improved mechanical properties in relation to the synthetic polymer in the packaging production, a complete factorial design 23 was carried out in order to investigate which factor significantly influences the tensile strength of the biofilm. The factors to be investigated were cassava starch, glycerol and modified clay contents. Modified bentonite clay was used as a filling material of the biofilm. Glycerol was the plasticizer used to thermoplastify cassava starch. The factorial analysis suggested a regression model capable of predicting the optimal mechanical property of the cassava starch film from the maximization of the tensile strength. The reliability of the regression model was tested by the correlation established with the experimental data through the following statistical analyse: Pareto graph. The modified clay was the factor of greater statistical significance on the observed response variable, being the factor that contributed most to the improvement of the mechanical property of the starch film. The factorial experiments showed that the interaction of glycerol with both modified clay and cassava starch was significant for the reduction of biofilm ductility. Modified clay and cassava starch contributed to the maximization of biofilm ductility, while glycerol contributed to the minimization.

Some engineering aspects of homoionized mixed clay minerals.

PubMed

Oren, Ali Hakan; Kaya, Abidin

2003-05-01

Many studies have been conducted to investigate the physicochemical behavior of pure clay minerals and predict their engineering performance in the field. In this study, the physicochemical properties of an artificial mixture of different clay minerals namely, 40-50% montmorillonite, 20-30% illite and 10-15% kaolin were investigated. The mixture was homoionized with sodium, Na+; calcium, Ca2+; and aluminum, Al3+. The engineering properties studied were consistency limits, sediment volume, compressibility behavior, and hydraulic conductivity. The results revealed that the liquid, plastic and shrinkage limits of soil increased with increasing cation valence. The hydraulic conductivity of the soil also increased with an increase in the valence of the cation at any given void ratio. Aluminum and sodium treated clays had the highest and the lowest modified compression index values, respectively. Furthermore, trivalent cation saturated clayey soil consolidates three times faster than that of monovalent and two times faster than that of divalent. These properties of the soils determined were, in general, similar to those of kaolinite rather than those of montmorillonite. The comparison of the results obtained with the published data in the literature revealed that the physicochemical behavior of the tested clay soil was, in general, similar to that of kaolinite.

Heavy metal content and potential health risk of geophagic white clay from the Kumasi Metropolis in Ghana.

PubMed

Nkansah, Marian Asantewah; Korankye, Mavis; Darko, Godfred; Dodd, Matt

2016-01-01

Geophagia is the craving for non-food substances and commonly practiced among pregnant women and children. Consumption of geophagic clay samples can have serious implications on the health of the consumers as a result of the presence of toxic metals such as Pb, As, Hg and Cd. This study sought to determine the levels of heavy metals in the studied geophagic clay samples and to determine the potential risks of heavy metals as cumulative carcinogenic and non-carcinogenic risks to the health of the consumers via oral (ingestion) and dermal exposure routes. A total of thirty (30) white clay samples were analysed using Niton Thermo scientific XRF Analyser (Mobile Test S, NDTr-XL3t-86956, com 24). The clay samples were found to contain essential elements such as Ca, Fe, K and Zn as well as toxic metals such as As and Pb. There were isolated cases of the presence of Hg and all samples had Cd levels below detection. Health risk indices such as hazard quotient and cancer risk were calculated and the results indicated that consumers are likely to suffer from cancer through ingestion of geophagic clay. Bioaccessibility studies were done on zinc and it did not indicate any potential toxicity due to zincs essential nature. The levels of heavy metals in some of the geophagic clay consumed by some residents in the Kumasi were high compared to the Permitted Maximum Tolerable Daily Intake (PMTDI) by (WHO/FAO) and may pose potential health threat over time.

Piezo-resistivity electric cone penetration technology investigation of the M-basin at the Savannah River Site, Aiken, South Carolina. Progress report, May 1, 1992--October 31, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowers, B.; Rossabi, J.; Shinn, J.D. II

1997-05-01

This report documents the results of a combined field and laboratory investigation program to: (1) delineate the geologic layering and (2) determine the location of a dense non-aqueous liquid-phase (DNAPL) contaminated plume beneath the M Area Hazardous Waste Management Facility at the Savannah River Plant. During April of 1991, DNAPLs were detected in monitoring well (MSB-3D), located adjacent to the capped M-Area Settling Basin. Solvents in the well consisted mainly of tetrachloroethylene and trichloroethylene, which are also the main solvents found in groundwater in the M Area. In permeable soils, DNAPLs move downward rapidly due to their high density andmore » low viscosity as compared to water. Within the vadose zone, DNAPLs tend to be held by the less permeable clay and silts by capillary force. In the saturated zone, the downward movement is slowed by clays and silts and the DNAPL tends to pool on this layer, then spread laterally. The lateral movement continues until a permeable layer is encountered, which can be a sand lens, fracture or other high conductivity seam. The DNAPL then moves downward, until another low permeability layer is encountered. Applied Research Associates was contracted to conduct a program to: (1) field demonstrate the utility of Cone Penetration Technology to investigate DOE contaminant sites and, (2) conduct a laboratory and field program to evaluate the use of electric resistivity surveys to locate DNAPL contaminated soils. The field program was conducted in the M-Basin and laboratory tests were conducted on samples from the major stratigraphy units as identified in Eddy et. al. Cone Penetration Technology was selected to investigate the M-Basin as it: (1) is minimally invasive, (2) generates minimal waste, (3) is faster and less costly than drilling, (4) provides continuous, detailed in situ characterization data, (5) permits real-time data processing, and (6) can obtain soil, soil gas, and water samples without the need for a boring.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knox, Anna Sophia; Paller, Michael H.; Milliken, Charles E.

One challenge to all remedial approaches for contaminated sediments is the continued influx of contaminants from uncontrolled sources following remediation. We investigated the effects of ongoing contamination in mesocosms employing sediments remediated by different types of active and passive caps and in-situ treatment. Our hypothesis was that the sequestering agents used in active caps and in situ treatment will bind elements (arsenic, chromium, cadmium, cobalt, copper, nickel, lead, selenium, and zinc) from ongoing sources thereby reducing their bioavailability and protecting underlying remediated sediments from recontamination. Most element concentrations in surface water remained significantly lower in mesocosms with apatite and mixedmore » amendment caps than in mesocosms with passive caps (sand), uncapped sediment, and spike solution throughout the 2520 hour experiment. Element concentrations were significantly higher in Lumbriculus variegatus from untreated sediment than in Lumbriculus from most active caps. Moreover, Pearson correlations between element concentrations in Lumbriculus and metal concentrations in the top 2.5 cm of sediment or cap measured by diffusive gradient in thin films (DGT) sediment probes were generally strong (as high as 0.98) and significant (p<0.05) for almost all tested elements. Metal concentrations in both Lumbriculus and sediment/cap were lowest in apatite, mixed amendment, and activated carbon treatments. Finally, these findings show that some active caps can protect remediated sediments by reducing the bioavailable pool of metals/metalloids in ongoing sources of contamination.« less

Enhanced biocorrosion resistance and biocompatibility of degradable Mg-Nd-Zn-Zr alloy by brushite coating.

PubMed

Niu, Jialin; Yuan, Guangyin; Liao, Yi; Mao, Lin; Zhang, Jian; Wang, Yongping; Huang, Feng; Jiang, Yao; He, Yaohua; Ding, Wenjiang

2013-12-01

To further improve the corrosion resistance and biocompatibility of Mg-Nd-Zn-Zr alloy (JDBM), a biodegradable calcium phosphate coating (Ca-P coating) with high bonding strength was developed using a novel chemical deposition method. The main composition of the Ca-P coating was brushite (CaHPO4·2H2O). The bonding strength between the coating and the JDBM substrate was measured to be over 10 MPa, and the thickness of the coating layer was about 10-30 μm. The in vitro corrosion tests indicated that the Ca-P treatment improved the corrosion resistance of JDBM alloy in Hank's solution. Ca-P treatment significantly reduced the hemolysis rate of JDBM alloy from 48% to 0.68%, and induced no toxicity to MC3T3-E1 cells. The in vivo implantation experiment in New Zealand's rabbit tibia showed that the degradation rate was reduced obviously by the Ca-P treatment and less gas was produced from Ca-P treated JDBM bone plates and screws in early stage of the implantation, and at least 10weeks degradation time can be prolonged by the present coating techniques. Both Ca-P treated and untreated JDBM Mg alloy induced bone growth. The primary results indicate that the present Ca-P treatment is a promising technique for the degradable Mg-based biomaterials for orthopedic applications. © 2013.

Environmental impact of ongoing sources of metal contamination on remediated sediments

DOE PAGES

Knox, Anna Sophia; Paller, Michael H.; Milliken, Charles E.; ...

2016-04-29

One challenge to all remedial approaches for contaminated sediments is the continued influx of contaminants from uncontrolled sources following remediation. We investigated the effects of ongoing contamination in mesocosms employing sediments remediated by different types of active and passive caps and in-situ treatment. Our hypothesis was that the sequestering agents used in active caps and in situ treatment will bind elements (arsenic, chromium, cadmium, cobalt, copper, nickel, lead, selenium, and zinc) from ongoing sources thereby reducing their bioavailability and protecting underlying remediated sediments from recontamination. Most element concentrations in surface water remained significantly lower in mesocosms with apatite and mixedmore » amendment caps than in mesocosms with passive caps (sand), uncapped sediment, and spike solution throughout the 2520 hour experiment. Element concentrations were significantly higher in Lumbriculus variegatus from untreated sediment than in Lumbriculus from most active caps. Moreover, Pearson correlations between element concentrations in Lumbriculus and metal concentrations in the top 2.5 cm of sediment or cap measured by diffusive gradient in thin films (DGT) sediment probes were generally strong (as high as 0.98) and significant (p<0.05) for almost all tested elements. Metal concentrations in both Lumbriculus and sediment/cap were lowest in apatite, mixed amendment, and activated carbon treatments. Finally, these findings show that some active caps can protect remediated sediments by reducing the bioavailable pool of metals/metalloids in ongoing sources of contamination.« less

Closure Report for Corrective Action Unit 426: Cactus Spring Waste Trenches, Tonopah Test Range, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dave Madsen

This Closure Report provides the documentation for closure of the Cactus Spring Waste Trenches Corrective Action Unit (CAU) 426. The site is located on the Tonopah Test Range, approximately 225 kilometers northwest of Las Vegas, NV. CAU 426 consists of one corrective action site (CAS) which is comprised of four waste trenches. The trenches were excavated to receive solid waste generated in support of Operation Roller Coaster, primary the Double Tracks Test in 1963, and were subsequently backfilled. The Double Tracks Test involved use of live animals to assess the biological hazards associated with the nonnuclear detonation of plutonium-bearing devices.more » The Nevada Division of Environmental Protection approved Corrective Action Plan (CAP)which proposed ''capping'' methodology. The closure activities were completed in accordance with the approved CAP and consisted of constructing an engineered cover in the area of the trenches, constructing/planting a vegetative cover, installing a perimeter fence and signs, implementing restrictions on future use, and preparing a Post-Closure Monitoring Plan.« less

Microbiologically Influenced Corrosion

DTIC Science & Technology

2015-11-05

high in water content, are less corrosive owing to their elevated viscosity and resulting low conductivity (᝺-7 S/cm) [30]. Asphaltenes and resins...wet surface to a water-wet surface. Sludge deposits are combinations of hydrocarbons, sand, clay , corTosion prod- ucts, and biomass that can reach 50...fine clay sun·ounded by a film of water. Under low flow conditions, these particles precipitate and form a sludge deposit. 27.4 TESTING 27 .4.1 A

Reformulation of the CBR Procedure. Report 1: Basic Report

DTIC Science & Technology

2012-04-01

originate a superior method of compaction control, the modified density test associated with the name of Ralph R. Proctor . In time, Porter was able to...enough for the subsoil moisture to equalize. Colonel Bragdon in the South Atlantic Division was to choose an airstrip built on sandy clay , a fairly good...subsoil; Colonel Scott in the Southwestern Division, one of lean black clay , a rather poor foundation; Colonel Elliott in the Upper Mississippi

Severity of influenza A 2009 (H1N1) pneumonia is underestimated by routine prediction rules. Results from a prospective, population-based study.

PubMed

Bjarnason, Agnar; Thorleifsdottir, Gudlaug; Löve, Arthur; Gudnason, Janus F; Asgeirsson, Hilmir; Hallgrimsson, Kristinn L; Kristjansdottir, Berglind S; Haraldsson, Gunnsteinn; Baldursson, Olafur; Kristinsson, Karl G; Gottfredsson, Magnus

2012-01-01

Characteristics of patients with community-acquired pneumonia (CAP) due to pandemic influenza A 2009 (H1N1) have been inadequately compared to CAP caused by other respiratory pathogens. The performance of prediction rules for CAP during an epidemic with a new infectious agent are unknown. Prospective, population-based study from November 2008-November 2009, in centers representing 70% of hospital beds in Iceland. Patients admitted with CAP underwent evaluation and etiologic testing, including polymerase chain reaction (PCR) for influenza. Data on influenza-like illness in the community and overall hospital admissions were collected. Clinical and laboratory data, including pneumonia severity index (PSI) and CURB-65 of patients with CAP due to H1N1 were compared to those caused by other agents. Of 338 consecutive and eligible patients 313 (93%) were enrolled. During the pandemic peak, influenza A 2009 (H1N1) patients constituted 38% of admissions due to CAP. These patients were younger, more dyspnoeic and more frequently reported hemoptysis. They had significantly lower severity scores than other patients with CAP (1.23 vs. 1.61, P= .02 for CURB-65, 2.05 vs. 2.87 for PSI, P<.001) and were more likely to require intensive care admission (41% vs. 5%, P<.001) and receive mechanical ventilation (14% vs. 2%, P= .01). Bacterial co-infection was detected in 23% of influenza A 2009 (H1N1) patients with CAP. Clinical characteristics of CAP caused by influenza A 2009 (H1N1) differ markedly from CAP caused by other etiologic agents. Commonly used CAP prediction rules often failed to predict admissions to intensive care or need for assisted ventilation in CAP caused by the influenza A 2009 (H1N1) virus, underscoring the importance of clinical acumen under these circumstances.

Severity of Influenza A 2009 (H1N1) Pneumonia Is Underestimated by Routine Prediction Rules. Results from a Prospective, Population-Based Study

PubMed Central

Bjarnason, Agnar; Thorleifsdottir, Gudlaug; Löve, Arthur; Gudnason, Janus F.; Asgeirsson, Hilmir; Hallgrimsson, Kristinn L.; Kristjansdottir, Berglind S.; Haraldsson, Gunnsteinn; Baldursson, Olafur; Kristinsson, Karl G.; Gottfredsson, Magnus

2012-01-01

Background Characteristics of patients with community-acquired pneumonia (CAP) due to pandemic influenza A 2009 (H1N1) have been inadequately compared to CAP caused by other respiratory pathogens. The performance of prediction rules for CAP during an epidemic with a new infectious agent are unknown. Methods Prospective, population-based study from November 2008–November 2009, in centers representing 70% of hospital beds in Iceland. Patients admitted with CAP underwent evaluation and etiologic testing, including polymerase chain reaction (PCR) for influenza. Data on influenza-like illness in the community and overall hospital admissions were collected. Clinical and laboratory data, including pneumonia severity index (PSI) and CURB-65 of patients with CAP due to H1N1 were compared to those caused by other agents. Results Of 338 consecutive and eligible patients 313 (93%) were enrolled. During the pandemic peak, influenza A 2009 (H1N1) patients constituted 38% of admissions due to CAP. These patients were younger, more dyspnoeic and more frequently reported hemoptysis. They had significantly lower severity scores than other patients with CAP (1.23 vs. 1.61, P = .02 for CURB-65, 2.05 vs. 2.87 for PSI, P<.001) and were more likely to require intensive care admission (41% vs. 5%, P<.001) and receive mechanical ventilation (14% vs. 2%, P = .01). Bacterial co-infection was detected in 23% of influenza A 2009 (H1N1) patients with CAP. Conclusions Clinical characteristics of CAP caused by influenza A 2009 (H1N1) differ markedly from CAP caused by other etiologic agents. Commonly used CAP prediction rules often failed to predict admissions to intensive care or need for assisted ventilation in CAP caused by the influenza A 2009 (H1N1) virus, underscoring the importance of clinical acumen under these circumstances. PMID:23071646

Goat's milk allergy without cow's milk allergy: suppression of non-cross-reactive epitopes on caprine β-casein.

PubMed

Hazebrouck, S; Ah-Leung, S; Bidat, E; Paty, E; Drumare, M-F; Tilleul, S; Adel-Patient, K; Wal, J-M; Bernard, H

2014-04-01

Goat's milk (GM) allergy associated with tolerance to cow's milk (CM) has been reported in patients without history of CM allergy and in CM-allergic children successfully treated with oral immunotherapy. The IgE antibodies from GM-allergic/CM-tolerant patients recognize caprine β-casein (βcap) without cross-reacting with bovine β-casein (βbov) despite a sequence identity of 91%. In this study, we investigated the non-cross-reactive IgE-binding epitopes of βcap. Recombinant βcap was genetically modified by substituting caprine domains with the bovine counterparts and by performing site-directed mutagenesis. We then evaluated the recognition of modified βcap by IgE antibodies from 11 GM-allergic/CM-tolerant patients and 11 CM-allergic patients or by monoclonal antibodies (mAb) raised against caprine caseins. The allergenic potency of modified βcap was finally assessed by degranulation tests of humanized rat basophil leukaemia (RBL)-SX38 cells. Non-cross-reactive epitopes of βcap were found in domains 44-88 and 130-178. The substitutions A55T/T63P/L75P and P148H/S152P induced the greatest decrease in IgE reactivity of GM-allergic/CM-tolerant patients towards βcap. The pivotal role of threonine 63 was particularly revealed as its substitution also impaired the recognition of βcap by specific mAb, which could discriminate between βcap and βbov. The modified βcap containing the five substitutions was then unable to trigger the degranulation of RBL-SX38 cells passively sensitized with IgE antibodies from GM-allergic/CM-tolerant patients. Although IgE-binding epitopes are spread all over βcap, a non-cross-linking version of βcap was generated with only five amino acid substitutions and could thus provide new insight for the design of hypoallergenic variants. © 2013 John Wiley & Sons Ltd.

Mineralogy of fine-grained alluvium from borehole U11g, expl. 1, northern Frenchman Flat area, Nevada Test Site

USGS Publications Warehouse

Jones, B.F.

1982-01-01

The mineralogy of matrix fines in alluvium from borehole Ullg, expl. 1, north of Frenchman Flat, Nevada Test Site, has been examined for evidence of past variations in water table elevation. Although greater abundance of zeolite and slightly more expanded basal spacings in smectite clays suggest effects of increased hydration of material up to 50 m above the present water table, these differences might also be related to provenance of environment of deposition. The relative uniformity of clay hydration properties in the 50 meters above the current water table suggest long-term stability near the present level. (USGS)

Atypical aetiology in patients hospitalised with community-acquired pneumonia is associated with age, gender and season; a data-analysis on four Dutch cohorts.

PubMed

Raeven, Vivian M; Spoorenberg, Simone M C; Boersma, Wim G; van de Garde, Ewoudt M W; Cannegieter, Suzanne C; Voorn, G P Paul; Bos, Willem Jan W; van Steenbergen, Jim E

2016-06-17

Microorganisms causing community-acquired pneumonia (CAP) can be categorised into viral, typical and atypical (Legionella species, Coxiella burnetii, Mycoplasma pneumoniae, and Chlamydia species). Extensive microbiological testing to identify the causative microorganism is not standardly recommended, and empiric treatment does not always cover atypical pathogens. In order to optimize epidemiologic knowledge of CAP and to improve empiric antibiotic choice, we investigated whether atypical microorganisms are associated with a particular season or with the patient characteristics age, gender, or chronic obstructive pulmonary disease (COPD). A data-analysis was performed on databases from four prospective studies, which all included adult patients hospitalised with CAP in the Netherlands (N = 980). All studies performed extensive microbiological testing. A main causative agent was identified in 565/980 (57.7 %) patients. Of these, 117 (20.7 %) were atypical microorganisms. This percentage was 40.4 % (57/141) during the non-respiratory season (week 20 to week 39, early May to early October), and 67.2 % (41/61) for patients under the age of 60 during this season. Factors that were associated with atypical causative agents were: CAP acquired in the non-respiratory season (odds ratio (OR) 4.3, 95 % CI 2.68-6.84), age <60 year (OR 2.9, 95 % CI 1.83-4.66), male gender (OR 1.7, 95 % CI 1.06-2.71) and absence of COPD (OR 0.2, 95 % CI 0.12-0.52). Atypical causative agents in CAP are associated with respectively non-respiratory season, age <60 years, male gender and absence of COPD. Therefore, to maximise its yield, extensive microbiological testing should be considered in patients <60 years old who are admitted with CAP from early May to early October. NCT00471640 , NCT00170196 (numbers of original studies).

Outcomes of direct pulp capping: interrogating an insurance database.

PubMed

Raedel, M; Hartmann, A; Bohm, S; Konstantinidis, I; Priess, H W; Walter, M H

2016-11-01

To evaluate the effectiveness of direct pulp capping under general practice conditions. It was hypothesized that direct pulp capping is an effective procedure in the majority of cases and prevents the need for root canal treatment or extraction. Claims data were collected from the digital database of a major German national health insurance company. Only patients who had been insurance members for the entire 3 year period 2010 to 2012 were eligible. Kaplan-Meier survival analyses were conducted for all teeth with direct pulp capping. Success was defined as not undergoing root canal treatment. Survival was defined as not undergoing extraction. Differences between survival functions were tested with the log rank test. A total of 148 312 teeth were included. The overall success rate was 71.6% at 3 years. The overall survival rate was 95.9% at 3 years. The success rates for single-rooted teeth (71.8%) and multirooted teeth (71.5%) were similar although significantly different (P < 0.001). Best 3-year success rates were found at low (79.7%; <18 years.) and very high age (81.8%; >85 years.). After direct pulp capping, more than two-thirds of the affected teeth did not undergo root canal treatment within 3 years. Although this study has the typical limits of a claims data analysis, it can be concluded that direct pulp capping is an effective intervention to avoid root canal treatment and extraction in a general practice setting. © 2015 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Dynamic load testing on the bearing capacity of prestressed tubular concrete piles in soft ground

NASA Astrophysics Data System (ADS)

Yu, Chuang; Liu, Songyu

2008-11-01

Dynamic load testing (DLT) is a high strain test method for assessing pile performance. The shaft capacity of a driven PTC (prestressed tubular concrete) pile in marine soft ground will vary with time after installation. The DLT method has been successfully transferred to the testing of prestressed pipe piles in marine soft clay of Lianyungang area in China. DLT is investigated to determine the ultimate bearing capacity of single pile at different period after pile installation. The ultimate bearing capacity of single pile was founded to increase more than 70% during the inventing 3 months, which demonstrate the time effect of rigid pile bearing capacity in marine soft ground. Furthermore, the skin friction and axial force along the pile shaft are presented as well, which present the load transfer mechanism of pipe pile in soft clay. It shows the economy and efficiency of DLT method compared to static load testing method.

CAP/ACMG proficiency testing for biochemical genetics laboratories: a summary of performance.

PubMed

Oglesbee, Devin; Cowan, Tina M; Pasquali, Marzia; Wood, Timothy C; Weck, Karen E; Long, Thomas; Palomaki, Glenn E

2018-01-01

PurposeTesting for inborn errors of metabolism is performed by clinical laboratories worldwide, each utilizing laboratory-developed procedures. We sought to summarize performance in the College of American Pathologists' (CAP) proficiency testing (PT) program and identify opportunities for improving laboratory quality. When evaluating PT data, we focused on a subset of laboratories that have participated in at least one survey since 2010.MethodsAn analysis of laboratory performance (2004 to 2014) on the Biochemical Genetics PT Surveys, a program administered by CAP and the American College of Medical Genetics and Genomics. Analytical and interpretive performance was evaluated for four tests: amino acids, organic acids, acylcarnitines, and mucopolysaccharides.ResultsSince 2010, 150 laboratories have participated in at least one of four PT surveys. Analytic sensitivities ranged from 88.2 to 93.4%, while clinical sensitivities ranged from 82.4 to 91.0%. Performance was higher for US participants and for more recent challenges. Performance was lower for challenges with subtle findings or complex analytical patterns.ConclusionUS clinical biochemical genetics laboratory proficiency is satisfactory, with a minority of laboratories accounting for the majority of errors. Our findings underscore the complex nature of clinical biochemical genetics testing and highlight the necessity of continuous quality management.

Correlation analysis of two serum-specific immunoglobulin E test systems and skin-prick test in allergic rhinitis patients from northeast China.

PubMed

Jiang, Xiao-Dan; Li, Guang-Yu; Dong, Zhen; Zhu, Dong-Dong

2011-01-01

Skin-prick testing (SPT) is the most common screening method for allergy evaluation. The detection of serum-specific immunoglobulin E (sIgE) is also commonly used. The sensitivity and specificity of these testing methods may vary due to type of causative allergen and type of allergic manifestation. The purpose of this study was to evaluate the correlation between two methods of measuring sIgE (AllergyScreen [Mediwiss Analytic GmbH, Moers, Germany] and ImmunoCAP [Pharmacia, Uppsala, Sweden]) and SPT for the diagnosis of allergic rhinitis (AR). All 216 patients who were referred to the allergist for suspected AR from June to October 2009 had SPT and the two serological tests. One hundred fifty-eight patients had a positive clinical history and a related positive SPT. The SPT was used as reference standard, and we selected three allergens (Dermatophagoides pteronyssinus, mugwort, and ragweed), which were common in fall in northeast China, to analyze the correlation of the two serum tests and SPT. Compared with the SPT, the diagnostic indexes (accuracy, sensitivity and specificity) of the AllergyScreen system and the ImmunoCAP system were 0.819 versus 0.810, 0.780 versus 0.872, and 0.862 versus 0.741, respectively. The accuracy was similar between the two systems (p > 0.05). The ImmunoCAP system method had a higher sensitivity (p < 0.01). The AllergyScreen system had a higher specificity (p < 0.01). These data support that the AllergyScreen system and ImmunoCAP system can identify potentially significant allergens in the diagnosis of AR in patients from northeastern China.

Comparative evaluation of the Cobas Amplicor HIV-1 Monitor Ultrasensitive Test, the new Cobas AmpliPrep/Cobas Amplicor HIV-1 Monitor Ultrasensitive Test and the Versant HIV RNA 3.0 assays for quantitation of HIV-1 RNA in plasma samples.

PubMed

Berger, Annemarie; Scherzed, Lina; Stürmer, Martin; Preiser, Wolfgang; Doerr, Hans Wilhelm; Rabenau, Holger Felix

2005-05-01

There are several commercially available assays for the quantitation of HIV RNA. A new automated specimen preparation system, the Cobas AmpliPrep, was developed to automate this last part of the PCR. We compared the results obtained by the Roche Cobas Amplicor HIV-1 Monitor Ultrasensitive Test (MCA, manual sample preparation) with those by the Versant HIV-1 RNA 3.0 assay (bDNA). Secondly we compared the MCA with the new Cobas AmpliPrep/Cobas Amplicor HIV Monitor Ultrasensitive Test (CAP/CA, automated specimen preparation) by investigating clinical patient samples and a panel of HIV-1 non-B subtypes. Furthermore, we assessed the assay throughput and workflow (especially hands-on time) for all three assays. Seventy-two percent of the 140 investigated patient samples gave concordant results in the bDNA and MCA assays. The MCA values were regularly higher than the bDNA values. One sample was detected only by the MCA within the linear range of quantification. In contrast, 38 samples with results <50 copies/ml in the MCA showed in the bDNA results between 51 and 1644 copies/ml (mean value 74 copies/ml); 21 of these specimens were shown to have detectable HIV RNA < 50 copies/ml in the MCA assay. The overall agreement between the MCA and the CAP/CA was 94.3% (551/584). The quantification results showed significant correlation, although the CAP/CA generated values slightly lower than those generated by the manual procedure. We found that the CAP/CA produced comparable results with the MCA test in a panel of HIV-1 non-B subtypes. All three assays showed comparable results. The bDNA provides a high sample throughput without the need of full automation. The new CAP/CA provides reliable test results with no HIV-subtype specific influence and releases time for other works in the laboratory; thus it is suitable for routine diagnostic PCR.

Apparatus for pre-stress-straining rod-type specimens in tension for in-situ passive fracture testing

DOEpatents

Wang, John Jy-an [Oak Ridge, TN; Liu, Ken C [Oak Ridge, TN; Feng, Zhili [Knoxville, TN

2013-07-31

A stress-strain testing apparatus imposes a stress-strain on a specimen while disposed in a controlled environment. Each end of the specimen is fastened to an end cap and a strain gage is attached to the specimen. An adjusting mechanism and a compression element are disposed between the end caps forming a frame for applying forces to the end caps and thereby stress-straining the specimen. The adjusting mechanism may be extended or retracted to increase or decrease the imposed stress-strain on the specimen, and the stress-strain is measured by the strain gage on the specimen while the apparatus is exposed to an environment such as high pressure hydrogen. Strain gages may be placed on the frame to measure stress-strains in the frame that may be caused by the environment.

Neural and receptor cochlear potentials obtained by transtympanic electrocochleography in auditory neuropathy.

PubMed

Santarelli, Rosamaria; Starr, Arnold; Michalewski, Henry J; Arslan, Edoardo

2008-05-01

Transtympanic electrocochleography (ECochG) was recorded bilaterally in children and adults with auditory neuropathy (AN) to evaluate receptor and neural generators. Test stimuli were clicks from 60 to 120dB p.e. SPL. Measures obtained from eight AN subjects were compared to 16 normally hearing children. Receptor cochlear microphonics (CMs) in AN were of normal or enhanced amplitude. Neural compound action potentials (CAPs) and receptor summating potentials (SPs) were identified in five AN ears. ECochG potentials in those ears without CAPs were of negative polarity and of normal or prolonged duration. We used adaptation to rapid stimulus rates to distinguish whether the generators of the negative potentials were of neural or receptor origin. Adaptation in controls resulted in amplitude reduction of CAP twice that of SP without affecting the duration of ECochG potentials. In seven AN ears without CAP and with prolonged negative potential, adaptation was accompanied by reduction of both amplitude and duration of the negative potential to control values consistent with neural generation. In four ears without CAP and with normal duration potentials, adaptation was without effect consistent with receptor generation. In five AN ears with CAP, there was reduction in amplitude of CAP and SP as controls but with a significant decrease in response duration. Three patterns of cochlear potentials were identified in AN: (1) presence of receptor SP without CAP consistent with pre-synaptic disorder of inner hair cells; (2) presence of both SP and CAP consistent with post-synaptic disorder of proximal auditory nerve; (3) presence of prolonged neural potentials without a CAP consistent with post-synaptic disorder of nerve terminals. Cochlear potential measures may identify pre- and post-synaptic disorders of inner hair cells and auditory nerves in AN.

Comparison of six Aspergillus-specific IgG assays for the diagnosis of chronic pulmonary aspergillosis (CPA).

PubMed

Page, Iain D; Richardson, Malcolm D; Denning, David W

2016-02-01

Chronic pulmonary aspergillosis (CPA) is estimated to affect 3 million persons worldwide. Aspergillus-specific IgG is a key component in CPA diagnosis. We aimed to establish the optimal diagnostic cut offs for CPA and the comparative performance of six assays in this context. Sera from 241 patients with CPA and 100 healthy blood donors were tested using five Aspergillus-specific IgG assays plus precipitin testing using Microgen Aspergillus antigens. Receiver operating characteristic (ROC) curve area under the curve (AUC) results were as follows: ThermoFisher Scientific ImmunoCAP 0.996 (95% confidence interval 0.992-1), Siemens Immulite 0.991 (0.982-1), Serion 0.973 (0.960-0.987), Dynamiker 0.918 (0.89-0.946) and Genesis 0.902 (0.871-0.933). Optimal CPA diagnostic cut-offs were; ImmunoCAP 20 mg/L (96% sensitivity, 98% specificity), Immulite 10 mg/L (96% sensitivity, 98% specificity), Serion 35 U/ml (90% sensitivity, 98% specificity), Dynamiker 65 AU/ml (77% sensitivity, 97% specificity) and Genesis 20 U/ml (75% sensitivity, 99% specificity). The precipitin test was 59% sensitive and 100% specific. ImmunoCAP and Immulite were statistically significantly superior to the other assays. Precipitins testing performed poorly. The currently accepted ImmunoCAP cut-off of 40 mg/L appears sub-optimal for CPA diagnosis and may require revision in this context. Copyright © 2015 The British Infection Association. Published by Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Liange; Li, Lianchong; Rutqvist, Jonny

Clay/shale has been considered as potential host rock for geological disposal of high-level nuclear waste throughout the world, because of its low permeability, low diffusion coefficient, high retention capacity for radionuclides, and capability to self-seal fractures induced by tunnel excavation. For example, Callovo-Oxfordian argillites at the Bure site, France (Fouche et al., 2004), Toarcian argillites at the Tournemire site, France (Patriarche et al., 2004), Opalinus Clay at the Mont Terri site, Switzerland (Meier et al., 2000), and Boom clay at the Mol site, Belgium (Barnichon and Volckaert, 2003) have all been under intensive scientific investigation (at both field and laboratorymore » scales) for understanding a variety of rock properties and their relationships to flow and transport processes associated with geological disposal of nuclear waste. Clay/shale formations may be generally classified as indurated or plastic clays (Tsang and Hudson, 2010). The latter (including Boom clay) is a softer material without high cohesion; its deformation is dominantly plastic. During the lifespan of a clay repository, the repository performance is affected by complex thermal, hydrogeological, mechanical, chemical (THMC) processes, such as heat release due to radionuclide decay, multiphase flow, formation of damage zones, radionuclide transport, waste dissolution, and chemical reactions. All these processes are related to each other. An in-depth understanding of these coupled processes is critical for the performance assessment (PA) of the repository. These coupled processes may affect radionuclide transport by changing transport paths (e.g., formation and evolution of excavation damaged zone (EDZ)) and altering flow, mineral, and mechanical properties that are related to radionuclide transport. While radionuclide transport in clay formation has been studied using laboratory tests (e,g, Appelo et al. 2010, Garcia-Gutierrez et al., 2008, Maes et al., 2008), short-term field tests (e.g. Garcia-Gutierrez et al. 2006, Soler et al. 2008, van Loon et al. 2004, Wu et al. 2009) and numerical modeling (de Windt et al. 2003; 2006), the effects of THMC processes on radionuclide transport are not fully investigated. The objectives of the research activity documented in this report are to improve a modeling capability for coupled THMC processes and to use it to evaluate the THMC impacts on radionuclide transport. This research activity addresses several key Features, Events and Processes (FEPs), including FEP 2.2.08, Hydrologic Processes, FEP 2.2.07, Mechanical Processes and FEP 2.2.09, Chemical Process— Transport, by studying near-field coupled THMC processes in clay/shale repositories and their impacts on radionuclide transport. This report documents the progress that has been made in FY12. Section 2 discusses the development of THMC modeling capability. Section 3 reports modeling results of THMC impacts on radionuclide transport. Planned work for the remaining months of FY12 and proposed work for FY13 are presented in Section 4.« less

Monitoring water content in Opalinus Clay within the FE-Experiment: Test application of dielectric water content sensors

NASA Astrophysics Data System (ADS)

Sakaki, T.; Vogt, T.; Komatsu, M.; Müller, H. R.

2013-12-01

The spatiotemporal variation of water content in the near field rock around repository tunnels for radioactive waste in clay formations is one of the essential quantities to be monitored for safety assessment in many waste disposal programs. Reliable measurements of water content are important not only for the understanding and prediction of coupled hydraulic-mechanic processes that occur during tunnel construction and ventilation phase, but also for the understanding of coupled thermal-hydraulic-mechanical (THM) processes that take place in the host rock during the post closure phase of a repository tunnel for spent fuel and high level radioactive waste (SF/HLW). The host rock of the Swiss disposal concept for SF/HLW is the Opalinus Clay formation (age of approx. 175 Million years). To better understand the THM effects in a full-scale heater-engineered barrier-rock system in Opalinus Clay, a full-scale heater test, namely the Full-Scale Emplacement (FE) experiment, was initiated in 2010 at the Mont Terri underground rock laboratory in north-western Switzerland. The experiment is designed to simulate the THM evolution of a SF/HLW repository tunnel based on the Swiss disposal concept in a realistic manner during the construction, emplacement, backfilling, and post-closure phases. The entire experiment implementation (in a 50 m long gallery with approx. 3 m diameter) as well as the post-closure THM evolution will be monitored using a network of several hundred sensors. The sensors will be distributed in the host rock, the tunnel lining, the engineered barrier, which consists of bentonite pellets and blocks, and on the heaters. The excavation is completed and the tunnel is currently being ventilated. Measuring water content in partially saturated clay-rich high-salinity rock with a deformable grain skeleton is challenging. Therefore, we use the ventilation phase (before backfilling and heating) to examine the applicability of commercial water content sensors and to design custom-made TDR sensors. The focus of this study is mainly on dielectric-based commercial water content sensors. Unlike soils for which the sensors were originally designed, it requires significantly more attention to properly install it onto rock (i.e., a good contact with the sensor and rock). The results will be used to select and design the instrumentation set-up for monitoring water content during the heating phase where sensors have to withstand harsh conditions (high salinity, high temperature, high pressures, high clay content and long term monitoring up to 10 years). The sensor tests are beneficial also in the sense that the water content data generated during these tests provide insights into drainage processes after tunnel construction and seasonal water content variations in the near field rock around the test gallery. We will present results from the tests and measurements performed during the first year.

Impact of positive psychological capital on employee well-being over time.

PubMed

Avey, James B; Luthans, Fred; Smith, Ronda M; Palmer, Noel F

2010-01-01

The recently recognized core construct of psychological capital or PsyCap (consisting of the positive psychological resources of efficacy, hope, optimism, and resilience) has been demonstrated to be related to various employee attitudinal, behavioral, and performance outcomes. However, to date, the impact of this positive core construct over time and on important employee well-being outcomes has not been tested. This study meets this need by analyzing the relationship between a broad cross-section of employees' (N = 280) level of PsyCap and two measures of psychological well-being over time. The results indicated that employees' PsyCap was related to both measures of well-being and, importantly, that PsyCap explained additional variance in these well-being measures over time. The limitations, needed future research, and practical implications conclude the article.

Effects of pulp capping materials on fracture resistance of Class II composite restorations

PubMed Central

Kucukyilmaz, Ebru; Yasa, Bilal; Akcay, Merve; Savas, Selcuk; Kavrik, Fevzi

2015-01-01

Objective: The aim of this study was to investigate the effect of cavity design and the type of pulp capping materials on the fracture resistance of Class II composite restorations. Materials and Methods: Sixty freshly extracted, sound molar teeth were selected for the study. A dovetail cavity on the mesio-occlusal and a slot cavity on disto-occlusal surfaces of each tooth were prepared, and the teeth were divided 4 groups which one of them as a control group. The pulp capping materials (TheraCal LC, Calcimol LC, Dycal) applied on pulpo-axial wall of each cavity, and the restoration was completed with composite resin. The teeth were subjected to a compressive load in a universal mechanical testing machine. The surfaces of the tooth and restoration were examined under a stereomicroscope. The data were analyzed using factorial analysis of variance and Tukey's test. Results: For pulp capping materials, the highest fracture load (931.15 ± 203.81 N) and the lowest fracture load (832.28 ± 245.75 N) were calculated for Control and Dycal group, respectively. However, there were no statistically significant differences among all groups (P > 0.05). The fracture load of the dovetail groups was significantly higher than those of the slot cavity groups (P < 0.05). Conclusion: Dovetail cavity design shows better fracture resistance in Class II composite restorations, independent of used or not used pulp capping materials. PMID:26038653

On the history of plasma treatment and comparison of microbiostatic efficacy of a historical high-frequency plasma device with two modern devices

PubMed Central

Napp, Judith; Daeschlein, Georg; Napp, Matthias; von Podewils, Sebastian; Gümbel, Denis; Spitzmueller, Romy; Fornaciari, Paolo; Hinz, Peter; Jünger, Michael

2015-01-01

Background: Cold atmospheric pressure plasma (CAP) with its many bioactive properties has defined a new medical field: the plasma medicine. However, in the related form of high-frequency therapy, CAP was even used briefly a century ago. The aim of this study was to review historic CAP treatments and to obtain data regarding the antimicrobial efficacy of a historical high-frequency plasma device. Methods: First, historic literature regarding the history of CAP treatment was evaluated, because in the modern literature no data were available. Second, the susceptibility of 5 different bacterial wound isolates, cultured on agar, to a historic plasma source (violet wand [VW]) and two modern devices (atmospheric pressure plasma jet [APPJ] and Dielectric Barrier Discharge [DBD]) was analyzed . The obtained inhibition areas (IA) were compared. Results: First, the most convenient popular historical electromedical treatments produced a so-called effluvia by using glass electrodes, related to today’s CAP. Second, all three tested plasma sources showed complete eradication of all tested microbial strains in the treated area. The “historical” cold VW plasma showed antimicrobial effects similar to those of modern APPJ and DBD regarding the diameter of the IA. Conclusion: Some retrograde evidence may be deducted from this, especially for treatment of infectious diseases with historical plasma devices. The underlying technology may serve as model for construction of modern sucessive devices. PMID:26124985

Comparison of Tasseled Cap-based Landsat data structures for use in forest disturbance detection.

Treesearch

Sean P. Healey; Warren B. Cohen; Yang Zhiqiang; Olga N. Krankina

2005-01-01

Landsat satellite data has become ubiquitous in regional-scale forest disturbance detection. The Tasseled Cap (TC) transformation for Landsat data has been used in several disturbance-mapping projects because of its ability to highlight relevant vegetation changes. We used an automated composite analysis procedure to test four multi-date variants of the TC...

Catastrophic antiphospholipid syndrome: a clinical review.

PubMed

Nayer, Ali; Ortega, Luis M

2014-01-01

Catastrophic antiphospholipid syndrome (CAPS) is a rare life-threatening autoimmune disease characterized by disseminated intravascular thrombosis resulting in multiorgan failure. Directory of Open Access Journals (DOAJ), Google Scholar, PubMed (NLM), LISTA (EBSCO) and Web of Science have been searched. CAPS is due to antiphospholipid antibodies directed against a heterogeneous group of proteins that are associated with phospholipids. These autoantibodies activate endothelial cells, platelets, and immune cells, thereby promoting a proinflammatory and prothrombotic phenotype. Furthermore, antiphospholipid antibodies inhibit anticoagulants, impair fibrinolysis, and activate complements. Although CAPS can affect a variety of organs and tissues, the kidneys, lungs, central nervous system, heart, skin, liver, and gastrointestinal tract are most commonly affected. The systemic inflammatory response syndrome, likely to extensive tissue damage, accompanies CAPS. The most frequent renal manifestations are hypertension, proteinuria, hematuria, and acute renal failure.In the majority of patients with CAPS, a precipitating factor such as infection, surgery, or medication can be identified. Antiphospholipid antibodies such as lupus anticoagulant and antibodies against cardiolipin, β2-glycoprotein I, and prothrombin are serological hallmark of CAPS. Laboratory tests often reveal antinuclear antibodies, thrombocytopenia, and anemia. Despite widespread intravascular coagulation, blood films reveal only a small number of schistocytes. In addition, severe thrombocytopenia is uncommon. Histologically, CAPS is characterized by acute thrombotic microangiopathy. CAPS must be distinguished from other forms of thrombotic microangiopathies such as hemolytic-uremic syndrome, thrombotic thrombocytopenic purpura, disseminated intravascular coagulation, and heparin-induced thrombocyt openia. CAPS is associated with high morbidity and mortality. Therefore, an aggressive multidisciplinary treatment strategy is indicated. Anticoagulation, immunosuppression, plasma exchange, intravenous immunoglobulins, and anti-platelet agents, used in various combinations, have resulted in improved patient outcome.

Resolving Large Pre-glacial Valleys Buried by Glacial Sediment Using Electric Resistivity Imaging (ERI)

NASA Astrophysics Data System (ADS)

Schmitt, D. R.; Welz, M.; Rokosh, C. D.; Pontbriand, M.-C.; Smith, D. G.

2004-05-01

Two-dimensional electric resistivity imaging (ERI) is the most exciting and promising geological tool in geomorphology and stratigraphy since development of ground-penetrating radar. Recent innovations in 2-D ERI provides a non-intrusive mean of efficiently resolving complex shallow subsurface structures under a number of different geological scenarios. In this paper, we test the capacity of ERI to image two large pre-late Wisconsinan-aged valley-fills in central Alberta and north-central Montana. Valley-fills record the history of pre-glacial and glacial sedimentary deposits. These fills are of considerable economical value as groundwater aquifers, aggregate resources (sand and gravel), placers (gold, diamond) and sometime gas reservoirs in Alberta. Although the approximate locations of pre-glacial valley-fills have been mapped, the scarcity of borehole (well log) information and sediment exposures make accurate reconstruction of their stratigraphy and cross-section profiles difficult. When coupled with borehole information, ERI successfully imaged three large pre-glacial valley-fills representing three contrasting geological settings. The Sand Coulee segment of the ancestral Missouri River, which has never been glaciated, is filled by electrically conductive pro-glacial lacustrine deposits over resistive sandstone bedrock. By comparison, the Big Sandy segment of the ancestral Missouri River valley has a complex valley-fill composed of till units interbedded with glaciofluvial gravel and varved clays over conductive shale. The fill is capped by floodplain, paludal and low alluvial fan deposits. The pre-glacial Onoway Valley (the ancestral North Saskatchewan River valley) is filled with thick, resistive fluvial gravel over conductive shale and capped with conductive till. The cross-sectional profile of each surveyed pre-glacial valley exhibits discrete benches (terraces) connected by steep drops, features that are hard to map using only boreholes. Best quality ERI results were obtained along the Sand Coulee and Onoway transects where the contrast between the bedrock and valley-fill was large and the surficial sediment was homogeneous. The effects of decreasing reliability with depth, 3-D anomalies, principles of equivalence and suppression, and surface inhomogeneity on the image quality are discussed.

Structural Testing of the Blade Reliability Collaborative Effect of Defect Wind Turbine Blades

DOE Office of Scientific and Technical Information (OSTI.GOV)

Desmond, M.; Hughes, S.; Paquette, J.

Two 8.3-meter (m) wind turbine blades intentionally constructed with manufacturing flaws were tested to failure at the National Wind Technology Center (NWTC) at the National Renewable Energy Laboratory (NREL) south of Boulder, Colorado. Two blades were tested; one blade was manufactured with a fiberglass spar cap and the second blade was manufactured with a carbon fiber spar cap. Test loading primarily consisted of flap fatigue loading of the blades, with one quasi-static ultimate load case applied to the carbon fiber spar cap blade. Results of the test program were intended to provide the full-scale test data needed for validation ofmore » model and coupon test results of the effect of defects in wind turbine blade composite materials. Testing was part of the Blade Reliability Collaborative (BRC) led by Sandia National Laboratories (SNL). The BRC seeks to develop a deeper understanding of the causes of unexpected blade failures (Paquette 2012), and to develop methods to enable blades to survive to their expected operational lifetime. Recent work in the BRC includes examining and characterizing flaws and defects known to exist in wind turbine blades from manufacturing processes (Riddle et al. 2011). Recent results from reliability databases show that wind turbine rotor blades continue to be a leading contributor to turbine downtime (Paquette 2012).« less

Cone penetration tests and soil borings at the Mason Road site in Green Valley, Solano County, California

USGS Publications Warehouse

Bennett, Michael J.; Noce, Thomas E.; Lienkaemper, James J.

2011-01-01

In support of a study to investigate the history of the Green Valley Fault, 13 cone penetration test soundings and 3 auger borings were made at the Mason Road site in Green Valley, Solano County, California. Three borings were made at or near two of the cone penetration test soundings. The soils are mostly clayey with a few sandy layers or lenses. Fine-grained soils range from low plasticity sandy lean clay to very plastic fat clay. Lack of stratigraphic correlation in the subsurface prevented us from determining whether any channels had been offset at this site. Because the soils are generally very clayey and few sand layers or lenses are loose, the liquefaction potential at the site is very low.

Inconsistent Results of Diagnostic Tools Hamper the Differentiation between Bee and Vespid Venom Allergy

PubMed Central

Sturm, Gunter J.; Jin, Chunsheng; Kranzelbinder, Bettina; Hemmer, Wolfgang; Sturm, Eva M.; Griesbacher, Antonia; Heinemann, Akos; Vollmann, Jutta; Altmann, Friedrich; Crailsheim, Karl; Focke, Margarete; Aberer, Werner

2011-01-01

Background Double sensitization (DS) to bee and vespid venom is frequently observed in the diagnosis of hymenoptera venom allergy, but clinically relevant DS is rare. Therefore it is sophisticated to choose the relevant venom for specific immunotherapy and overtreatment with both venoms may occur. We aimed to compare currently available routine diagnostic tests as well as experimental tests to identify the most accurate diagnostic tool. Methods 117 patients with a history of a bee or vespid allergy were included in the study. Initially, IgE determination by the ImmunoCAP, by the Immulite, and by the ADVIA Centaur, as well as the intradermal test (IDT) and the basophil activation test (BAT) were performed. In 72 CAP double positive patients, individual IgE patterns were determined by western blot inhibition and component resolved diagnosis (CRD) with rApi m 1, nVes v 1, and nVes v 5. Results Among 117 patients, DS was observed in 63.7% by the Immulite, in 61.5% by the CAP, in 47.9% by the IDT, in 20.5% by the ADVIA, and in 17.1% by the BAT. In CAP double positive patients, western blot inhibition revealed CCD-based DS in 50.8%, and the CRD showed 41.7% of patients with true DS. Generally, agreement between the tests was only fair and inconsistent results were common. Conclusion BAT, CRD, and ADVIA showed a low rate of DS. However, the rate of DS is higher than expected by personal history, indicating that the matter of clinical relevance is still not solved even by novel tests. Furthermore, the lack of agreement between these tests makes it difficult to distinguish between bee and vespid venom allergy. At present, no routinely employed test can be regarded as gold standard to find the clinically relevant sensitization. PMID:21698247

Musculoskeletal symptoms in patients with cryopyrin-associated periodic syndromes: a large database study.

PubMed

Houx, Laetitia; Hachulla, Eric; Kone-Paut, Isabelle; Quartier, Pierre; Touitou, Isabelle; Guennoc, Xavier; Grateau, Gilles; Hamidou, Mohamed; Neven, Bénédicte; Berthelot, Jean-Marie; Lequerré, Thierry; Pillet, Pascal; Lemelle, Irène; Fischbach, Michel; Duquesne, Agnès; Le Blay, Pierre; Le Jeunne, Claire; Stirnemann, Jérome; Bonnet, Christine; Gaillard, Dominique; Alix, Lilian; Touraine, Renaud; Garcier, François; Bedane, Christophe; Jurquet, Anne-Laure; Duffau, Pierre; Smail, Amar; Frances, Camille; Grall-Lerosey, Martine; Cathebras, Pascal; Tran, Tu Anh; Morell-Dubois, Sandrine; Pagnier, Anne; Richez, Christophe; Cuisset, Laurence; Devauchelle-Pensec, Valérie

2015-11-01

To determine the type and frequency of musculoskeletal symptoms at onset and during followup of cryopyrin-associated periodic syndromes (CAPS). We retrospectively recorded the articular and muscular symptoms of patients with CAPS followed up in French hospitals. Data were presented as frequencies or the median (range), and patient groups were compared using chi-square test, Fisher's exact test, and Mann-Whitney test. The study included 133 patients (33 children), 20 with familial cold autoinflammatory syndrome, 88 with Muckle-Wells syndrome, 22 with chronic infantile neurologic, cutaneous, articular syndrome, and 3 with unclassified CAPS. The median age was 35 years (range 0-78 years) at the time of the study, 1 year (range 0-41 years) at symptom onset, and 23 years (range 0-58 years) at diagnosis. The disease was sporadic in 17% of the patients. Cutaneous symptoms predominated at onset (77%), followed by articular symptoms (30%). The p.Thr348Met and p.Arg260Trp NLRP3 mutations were significantly associated with the presence and absence of articular symptoms at onset, respectively. During followup, 86% of the patients had musculoskeletal symptoms, 88% had arthralgia, and 58% had arthritis, but only 9% had joint destruction. Tendinopathies occurred in 21.5% of the patients, tender points in 16.5%, and myalgia in 33%. Only 3 patients had typical knee deformities. Radiographs were rarely obtained. Except for bone deformities, osteoarticular symptoms occurred at similar frequencies in the different CAPS phenotypes. Joint manifestations were frequent in all CAPS phenotypes. Bone deformities were rare. Musculoskeletal manifestations varied within given families but tended to worsen over time. © 2015, American College of Rheumatology.

Yield of coeliac screening in abdominal pain-associated functional gastrointestinal system disorders.

PubMed

Kansu, Aydan; Kuloğlu, Zarife; Demir, Arzu; Yaman, Aytaç

2015-11-01

Chronic abdominal pain (CAP) in childhood is common and in the majority functional. While CAP is one of the complaints of coeliac disease (CD), whether CAP as a sole complaint is indicative of CD is unclear. Our aim was to evaluate the relationship between CAP and CD. The study was conducted on 1047 children (61.1% female, mean age 9.6 ± 4.1 years) with CAP. Patients were evaluated according to the Rome III criteria. Patients with alarm symptoms and conditions known to be associated with CD were excluded. Patients were screened for CD using a rapid tissue transglutaminase (tTG) test; positive cases were tested by tTG ELISA, and duodenal biopsies were obtained if tTG was above the normal limit. Functional dyspepsia (FD), irritable bowel syndrome (IBS) and functional abdominal pain (FAP) were diagnosed in 384 (36.7%), 274 (26.2%) and 389 (37.2%) patients, respectively. In 13 patients, the tTG rapid test was positive; 10 were also positive for tTG by ELISA and histopathological evaluations diagnosed CD in all 10 patients. The overall prevalence of CD was 0.95% (2.2%, 0.5% and 0.5% in patients with IBS, FD and FAP, respectively). The prevalence of CD in patients with IBS was higher than expected but with borderline statistical significance (P = 0.053). CD is found as common in children with FD and FAP as in the general population. CD was more commonly diagnosed in IBS patients with borderline statistical significance. We suggest that particular attention be paid to children with IBS. © 2015 The Authors. Journal of Paediatrics and Child Health © 2015 Paediatrics and Child Health Division (Royal Australasian College of Physicians).

Experimental Study on the Interaction Between Contacting Barrier Materials for Containment of Radioactive Wastes

NASA Astrophysics Data System (ADS)

Huang, W. H.; Chang, H. C.

2017-12-01

The disposal of low- and intermediate-level radioactive wastes requires use of multi-barriers for isolation of the wastes from the biosphere. Typically, the engineered barriers are composed of a concrete vault, buffer and backfill materials. Zhishin clay and Black Hill bentonite were used as raw clay material in making buffer and backfill materials in this study. These clays were compacted to make buffer material, or mixed with Taitung area argillite to produce backfill material for potential application as barriers for the disposal of low- and intermediate-level radioactive wastes. The interaction between concrete barrier and the buffer/backfill material is simulated by an accelerated migration test to investigate the effect of contacting concrete on the expected functions of buffer/backfill material. The results show buffer material close to the contact with concrete exhibits significant change in the ratio of calcium/sodium exchange capacity, due to the move of calcium ions released from the concrete. The shorter the distance from the contacting interface, the ratio of the calcium/sodium concentration in buffer/backfill materials increases. The longer the distance from the interface, the effect of the contact on alteration in clays become less significant. Also, some decreases in swelling capacity in the buffer/backfill material near the concrete-backfill interface are noted. Finally, a comparison is made between Zhisin clay and Balck Hill bentonite on the interaction between concrete and the two clays. Black Hill bentonite was found to be influenced more by the interaction, because of the higher content of montmorillonite. On the other hand, being a mixture of clay and sand, backfill material is less affected by the decalsification of concrete at the contact than buffer material.

A parametric study on hydraulic conductivity and self-healing properties of geotextile clay liners used in landfills.

PubMed

Parastar, Fatemeh; Hejazi, Sayyed Mahdi; Sheikhzadeh, Mohammad; Alirezazadeh, Azam

2017-11-01

Nowadays, the raise of excessive generation of solid wastes is considered as a major environmental concern due to the fast global population growth. The contamination of groundwater from landfill leachate compromises every living creature. Geotextile clay liner (GCL) that has a sandwich structure with two fibrous sheets and a clay core can be considered as an engineered solution to prevent hazardous pollutants from entering into groundwater. The main objective of the present study is therefore to enhance the performance of GCL structures. By changing some structural factors such as clay type (sodium vs. calcium bentonite), areal density of clay, density of geotextile, geotextile thickness, texture type (woven vs. nonwoven), and needle punching density a series of GCL samples were fabricated. Water pressure, type of cover soil and overburden pressure were the environmental variables, while the response variables were hydraulic conductivity and self-healing rate of GCL. Rigid wall constant head permeability test was conducted on all the samples. The outlet water flow was measured and evaluated at a defined time period and the hydraulic conductivity was determined for each sample. In the final stage, self-healing properties of samples were investigated and an analytical model was used to explain the results. It was found that higher Montmorillonite content of clay, overburden pressure, needle punching density and areal density of clay poses better self-healing properties and less hydraulic conductivity, meanwhile, an increase in water pressure increases the hydraulic conductivity. Moreover, the observations were aligned with the analytical model and indicated that higher fiber inclusion as a result of higher needle-punching density produces closer contact between bentonite and fibers, reduces hydraulic conductivity and increases self-healing properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Soil forensics: How far can soil clay analysis distinguish between soil vestiges?

PubMed

Corrêa, R S; Melo, V F; Abreu, G G F; Sousa, M H; Chaker, J A; Gomes, J A

2018-03-01

Soil traces are useful as forensic evidences because they frequently adhere to individuals and objects associated with crimes and can place or discard a suspect at/from a crime scene. Soil is a mixture of organic and inorganic components and among them soil clay contains signatures that make it reliable as forensic evidence. In this study, we hypothesized that soils can be forensically distinguished through the analysis of their clay fraction alone, and that samples of the same soil type can be consistently distinguished according to the distance they were collected from each other. To test these hypotheses 16 Oxisol samples were collected at distances of between 2m and 1.000m, and 16 Inceptisol samples were collected at distances of between 2m and 300m from each other. Clay fractions were extracted from soil samples and analyzed for hyperspectral color reflectance (HSI), X-ray diffraction crystallographic (XRD), and for contents of iron oxides, kaolinite and gibbsite. The dataset was submitted to multivariate analysis and results were from 65% to 100% effective to distinguish between samples from the two soil types. Both soil types could be consistently distinguished for forensic purposes according to the distance that samples were collected from each other: 1000m for Oxisol and 10m for Inceptisol. Clay color and XRD analysis were the most effective techniques to distinguish clay samples, and Inceptisol samples were more easily distinguished than Oxisol samples. Soil forensics seems a promising field for soil scientists as soil clay can be useful as forensic evidence by using routine analytical techniques from soil science. Copyright © 2017 The Chartered Society of Forensic Sciences. Published by Elsevier B.V. All rights reserved.

A model for predicting embankment slope failures in clay-rich soils; A Louisiana example

NASA Astrophysics Data System (ADS)

Burns, S. F.

2015-12-01

A model for predicting embankment slope failures in clay-rich soils; A Louisiana example It is well known that smectite-rich soils significantly reduce the stability of slopes. The question is how much smectite in the soil causes slope failures. A study of over 100 sites in north and south Louisiana, USA, compared slopes that failed during a major El Nino winter (heavy rainfall) in 1982-1983 to similar slopes that did not fail. Soils in the slopes were tested for per cent clay, liquid limits, plasticity indices and semi-quantitative clay mineralogy. Slopes with the High Risk for failure (85-90% chance of failure in 8-15 years after construction) contained soils with a liquid limit > 54%, a plasticity index over 29%, and clay contents > 47%. Slopes with an Intermediate Risk (55-50% chance of failure in 8-15 years) contained soils with a liquid limit between 36-54%, plasticity index between 16-19%, and clay content between 32-47%. Slopes with a Low Risk chance of failure (< 5% chance of failure in 8-15 years after construction) contained soils with a liquid limit < 36%, a plasticity index < 16%, and a clay content < 32%. These data show that if one is constructing embankments and one wants to prevent slope failure of the 3:1 slopes, check the above soil characteristics before construction. If the soils fall into the Low Risk classification, construct the embankment normally. If the soils fall into the High Risk classification, one will need to use lime stabilization or heat treatments to prevent failures. Soils in the Intermediate Risk class will have to be evaluated on a case by case basis.

Exchangeable Ions Are Responsible for the In Vitro Antibacterial Properties of Natural Clay Mixtures

PubMed Central

Otto, Caitlin C.; Haydel, Shelley E.

2013-01-01

We have identified a natural clay mixture that exhibits in vitro antibacterial activity against a broad spectrum of bacterial pathogens. We collected four samples from the same source and demonstrated through antibacterial susceptibility testing that these clay mixtures have markedly different antibacterial activity against Escherichia coli and methicillin-resistant Staphylococcus aureus (MRSA). Here, we used X-ray diffraction (XRD) and inductively coupled plasma – optical emission spectroscopy (ICP-OES) and – mass spectrometry (ICP-MS) to characterize the mineralogical and chemical features of the four clay mixture samples. XRD analyses of the clay mixtures revealed minor mineralogical differences between the four samples. However, ICP analyses demonstrated that the concentrations of many elements, Fe, Co, Cu, Ni, and Zn, in particular, vary greatly across the four clay mixture leachates. Supplementation of a non-antibacterial leachate containing lower concentrations of Fe, Co, Ni, Cu, and Zn to final ion concentrations and a pH equivalent to that of the antibacterial leachate generated antibacterial activity against E. coli and MRSA, confirming the role of these ions in the antibacterial clay mixture leachates. Speciation modeling revealed increased concentrations of soluble Cu2+ and Fe2+ in the antibacterial leachates, compared to the non-antibacterial leachates, suggesting these ionic species specifically are modulating the antibacterial activity of the leachates. Finally, linear regression analyses comparing the log10 reduction in bacterial viability to the concentration of individual ion species revealed positive correlations with Zn2+ and Cu2+ and antibacterial activity, a negative correlation with Fe3+, and no correlation with pH. Together, these analyses further indicate that the ion concentration of specific species (Fe2+, Cu2+, and Zn2+) are responsible for antibacterial activity and that killing activity is not solely attributed to pH. PMID:23691149

The Prevalence of Oropharyngeal Dysphagia in Danish Patients Hospitalised with Community-Acquired Pneumonia.

PubMed

Melgaard, Dorte; Baandrup, Ulrik; Bøgsted, Martin; Bendtsen, Mette Dahl; Hansen, Tina

2017-06-01

Community-acquired pneumonia (CAP) and oropharyngeal dysphagia (OD) are prevalent conditions in the elderly. The aim of this study was to explore the relationship between CAP, OD, and frailty in patients admitted to a department of respiratory medicine at a regional hospital. The outcome was mortality during hospitalization and within 30 days of discharge and rehospitalization within 30 days of discharge. A total of 154 consecutive patients (54.5% male, mean age 77.4 years (SD 11.51)) hospitalized because of CAP from September 1, 2013 to March 31, 2014 at North Denmark Regional Hospital were included in this study. The volume-viscosity swallow test was conducted for each patient. A total of 34.42% patients presented with OD. Patients with OD and CAP presented significant differences in age, CURB-65, and dementia compared with those of patients with CAP alone. The majority lived in nursing homes, had a lower body mass index, Barthel 20 score, and handgrip strength, and had poor oral health compared with patients with CAP only. Patients with OD presented an increased length of stay in hospital (P < 0.001), intra-hospital mortality (P < 0.001), and 30-day mortality rate (P < 0.001) compared with those of patients with CAP only. Their rate of rehospitalization 0-30 days after discharge was also increased (P < 0.001) compared with that of patients with CAP only. Thus, OD is related to frailty and poor outcome.

Cold Atmospheric Plasma for Selectively Ablating Metastatic Breast Cancer Cells

PubMed Central

Wang, Mian; Holmes, Benjamin; Cheng, Xiaoqian; Zhu, Wei; Keidar, Michael; Zhang, Lijie Grace

2013-01-01

Traditional breast cancer treatments such as surgery and radiotherapy contain many inherent limitations with regards to incomplete and nonselective tumor ablation. Cold atomospheric plasma (CAP) is an ionized gas where the ion temperature is close to room temperature. It contains electrons, charged particles, radicals, various excited molecules, UV photons and transient electric fields. These various compositional elements have the potential to either enhance and promote cellular activity, or disrupt and destroy them. In particular, based on this unique composition, CAP could offer a minimally-invasive surgical approach allowing for specific cancer cell or tumor tissue removal without influencing healthy cells. Thus, the objective of this research is to investigate a novel CAP-based therapy for selectively bone metastatic breast cancer treatment. For this purpose, human metastatic breast cancer (BrCa) cells and bone marrow derived human mesenchymal stem cells (MSCs) were separately treated with CAP, and behavioral changes were evaluated after 1, 3, and 5 days of culture. With different treatment times, different BrCa and MSC cell responses were observed. Our results showed that BrCa cells were more sensitive to these CAP treatments than MSCs under plasma dose conditions tested. It demonstrated that CAP can selectively ablate metastatic BrCa cells in vitro without damaging healthy MSCs at the metastatic bone site. In addition, our study showed that CAP treatment can significantly inhibit the migration and invasion of BrCa cells. The results suggest the great potential of CAP for breast cancer therapy. PMID:24040051

Correlation of the controlled attenuation parameter with indices of liver steatosis in overweight or obese individuals: a pilot study.

PubMed

Ferraioli, Giovanna; Tinelli, Carmine; Lissandrin, Raffaella; Zicchetti, Mabel; Faliva, Milena; Perna, Simone; Perani, Guido; Alessandrino, Francesco; Calliada, Fabrizio; Rondanelli, Mariangela; Filice, Carlo

2015-03-01

The aim of this study was to assess the clinical relevance of the controlled attenuation parameter (CAP) by analyzing the correlations between CAP and indirect indices of liver steatosis in obese or overweight individuals. Consecutive participants were prospectively enrolled. BMI, waist circumference, hepatic steatosis index, fatty liver index, percent fat mass and regional fat masses as assessed by dual-energy X-ray absorptiometry (DXA), fat signal fraction as assessed by MRI, and CAP were obtained. Pearson's r coefficient was used to test the correlation between two study variables. A total of 88 individuals were studied. They included 31 men [age, 50.4 years (12.9 years); BMI, 30.7 kg/m (4.8 kg/m)] and 57 women [age, 49.0 years (12.6 years); BMI, 31.4 kg/m (5.6 kg/m)]. DXA, anthropometric parameters, and fatty liver index were moderately correlated with CAP in men. In women, there was a moderate correlation of CAP with the hepatic steatosis index and anthropometric parameters and only a slight or fair correlation of CAP with DXA parameters. CAP and fat signal fraction showed a good correlation (r=0.65 in men, P=0.002; r=0.68 in women, P=0.0009). Measurement of CAP is a reliable method for noninvasive assessment of liver steatosis, showing a correlation with other indirect markers of central obesity and a good correlation with MRI results.

The ultimate mineral processing challenge: Recovery of rare earths, phosphorus and uranium from Florida phosphatic clay

DOE PAGES

Zhang, Patrick; Liang, Haijun; Jin, Zhen; ...

2017-11-01

We report phosphate beneficiation in Florida generates more than one tonne of phosphatic clay, or slime, per tonne of phosphate rock produced. Since the start of the practice of large-scale washing and desliming for phosphate beneficiation, more than 2 Gt of slime has accumulated, containing approximately 600 Mt of phosphate rock, 600 kt of rare earth elements (REEs) and 80 million kilograms of uranium. The recovery of these valuable elements from the phosphatic clay is one of the most challenging endeavors in mineral processing, because the clay is extremely dilute, with an average solids concentration of 3 percent, and finemore » in size, with more than 50 percent having particle size smaller than 2 μm, and it contains nearly 50 percent clay minerals as well as large amounts of magnesium, iron and aluminum. With industry support and under funding from the Critical Materials Institute, the Florida Industrial and Phosphate Research Institute in conjunction with the Oak Ridge National Laboratory undertook the task to recover phosphorus, rare earths and uranium from Florida phosphatic clay. This paper presents the results from the preliminary testing of two approaches. The first approach involves three-stage cycloning using cyclones with diameters of 12.4 cm (5 in.), 5.08 cm (2 in.) and 2.54 cm (1 in.), respectively, to remove clay minerals followed by flotation and leaching. The second approach is a two-step leaching process. In the first step, selective leaching was conducted to remove magnesium, thus allowing the production of phosphoric acid suitable for the manufacture of diammonium phosphate (DAP) in the second leaching step. The results showed that multistage cycloning with small cyclones is necessary to remove clay minerals. Finally, selective leaching at about pH 3.2 using sulfuric acid was found to be effective for removing more than 80 percent of magnesium from the feed with minimal loss of phosphorus.« less

The ultimate mineral processing challenge: Recovery of rare earths, phosphorus and uranium from Florida phosphatic clay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Patrick; Liang, Haijun; Jin, Zhen

We report phosphate beneficiation in Florida generates more than one tonne of phosphatic clay, or slime, per tonne of phosphate rock produced. Since the start of the practice of large-scale washing and desliming for phosphate beneficiation, more than 2 Gt of slime has accumulated, containing approximately 600 Mt of phosphate rock, 600 kt of rare earth elements (REEs) and 80 million kilograms of uranium. The recovery of these valuable elements from the phosphatic clay is one of the most challenging endeavors in mineral processing, because the clay is extremely dilute, with an average solids concentration of 3 percent, and finemore » in size, with more than 50 percent having particle size smaller than 2 μm, and it contains nearly 50 percent clay minerals as well as large amounts of magnesium, iron and aluminum. With industry support and under funding from the Critical Materials Institute, the Florida Industrial and Phosphate Research Institute in conjunction with the Oak Ridge National Laboratory undertook the task to recover phosphorus, rare earths and uranium from Florida phosphatic clay. This paper presents the results from the preliminary testing of two approaches. The first approach involves three-stage cycloning using cyclones with diameters of 12.4 cm (5 in.), 5.08 cm (2 in.) and 2.54 cm (1 in.), respectively, to remove clay minerals followed by flotation and leaching. The second approach is a two-step leaching process. In the first step, selective leaching was conducted to remove magnesium, thus allowing the production of phosphoric acid suitable for the manufacture of diammonium phosphate (DAP) in the second leaching step. The results showed that multistage cycloning with small cyclones is necessary to remove clay minerals. Finally, selective leaching at about pH 3.2 using sulfuric acid was found to be effective for removing more than 80 percent of magnesium from the feed with minimal loss of phosphorus.« less

Interaction between the Bacterium Pseudomonas fluorescens strain CHA0, its genetic derivatives and vermiculite: Effects on chemical, mineralogical and mechanical properties of vermiculite

NASA Astrophysics Data System (ADS)

Mueller, Barbara

2016-04-01

Using bacteria of the strain Pseudomonas fluorescens wild type CHA0 and its genetic derivative strains CHA77, CHA89, CHA400, CHA631 and CHA661 (which differ in one gene only) the changes in chemical, mineralogical and rheological properties of the clay mineral vermiculite affected by microbial activity were studied in order to test whether the individually different production of metabolites by the genetically engineered strains may alter the clay mineral vermiculite in distinct ways. With the novel strategy of working with living wild type bacteria, their genetic derivatives and clay, the following properties of the mineral altered by the various strains of Pseudomonas fluorescens were determined: grain size, X-Ray diffraction pattern, intercrystalline swelling with glycerol, layer charge, CEC, BET surface and uptake of trace elements. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was used to determine the changes in major, minor and trace elements of the clay vermiculite affected by microbial activity. Among all analyzed trace elements, Fe, Mn and Cu are the most interesting. Fe and Mn are taken up from the clay mineral by all bacterial strains whereas Cu is only removed from vermiculite by strains CHA0, CHA77, CHA400 and CHA661. The latter mentioned strains all produce the antibiotics 2,4-diacetylphloroglucinol and monoacetylphloroglucinol which can complex Cu efficiently. Therefore the alteration of only one gene of the bacteria is causing significant effects on the clay mineral.

Role of Interfaces in Elasticity and Failure of Clay-Organic Nanocomposites: Toughening upon Interface Weakening?

PubMed

Hantal, György; Brochard, Laurent; Pellenq, Roland J-M; Ulm, Franz-Joseph; Coasne, Benoit

2017-10-24

Synthetic organic-inorganic composites constitute a new class of engineering materials finding applications in an increasing range of fields. The interface between the constituting phases plays a pivotal role in the enhancement of mechanical properties. In exfoliated clay-organic nanocomposites, individual, high aspect ratio clay sheets are dispersed in the organic matrix providing large interfaces and hence efficient stress transfer. In this study, we aim at elucidating molecular-scale reinforcing mechanisms in a series of model clay-organic composite systems by means of reactive molecular simulations. In our models, two possible locations of failure initiation are present: one is the interlayer space of the clay platelet, and the other one is the clay-organic interface. We systematically modify the cohesiveness of the interface and assess how the failure mechanism changes when the different model composites are subjected to a tensile test. Besides a change in the failure mechanism, an increase in the released energy at the interface (meaning an increased overall toughness) are observed upon weakening the interface by bond removal. We propose a theoretical analysis of these results by considering a cohesive law that captures the effect of the interface on the composite mechanics. We suggest an atomistic interpretation of this cohesive law, in particular, how it relates to the degree of bonding at the interface. In a broader perspective, this work sheds light on the importance of the orthogonal behavior of interfaces to nanocomposites.

An experimental study of the effects of adsorbing and non-adsorbing gases on friction and permeability evolution in clay-rich fault gouge

NASA Astrophysics Data System (ADS)

Lisabeth, H. P.; Zoback, M. D.

2017-12-01

Understanding the flow of fluids through fractures in clay-rich rocks is fundamental to a number of geoengineering enterprises, including development of unconventional hydrocarbon resources, nuclear waste storage and geological carbon sequestration. High clay content tends to make rocks plastic, low-porosity and anisotropic. In addition, some gasses adsorb to clay mineral surfaces, resulting in swelling and concomitant changes in physical properties. These complexities can lead to coupled behaviors that render prediction of fluid behavior in the subsurface difficult. We present the results of a suite of triaxial experiments on binary mixtures of quartz and illite grains to separate and quantify the effects of hydrostatic pressure, differential stress, clay content and gas chemistry on the evolution of mechanical and hydraulic characteristics of the gouge material during deformation. Tests are run on saw-cut samples prepared with gouge at 20 MPa confining pressure, 10 MPa pore pressure and at room temperature. Argon or carbon dioxide is used as pore fluid. Sample permeability, stress and strain are monitored continuously during hydrostatic and axial deformation. We find that pressure and shearing both lead to reductions in permeability. Adsorbing gas leads to swelling and promotes permeability reduction, but appears to have no effect on frictional properties. These results indicate that the seal integrity of clay-rich caprocks may not be compromised by shear deformation, and that depletion and shear deformation of unconventional reservoirs is expected to result in production declines.

Performance of two Aspergillus IgG EIA assays compared with the precipitin test in chronic and allergic aspergillosis.

PubMed

Baxter, C G; Denning, D W; Jones, A M; Todd, A; Moore, C B; Richardson, M D

2013-04-01

Detection of Aspergillus IgG antibodies is important in the diagnosis of chronic pulmonary aspergillosis and allergic bronchopulmonary aspergillosis. Immunoprecipitation techniques to detect these antibodies appear to lack sensitivity and accurate quantitation compared with enzyme immunoassays (EIA). This study assessed the performance of two commercial EIAs compared with counterimmunoelectrophoresis (CIE). This was a prospective cohort study of 175 adult patients with chronic or allergic pulmonary aspergillosis. Aspergillus IgG antibodies were detected using CIE, Phadia ImmunoCap Aspergillus IgG and Bio-Rad Platelia Aspergillus IgG. Inter-assay reproducibility was determined for each method and 25 patients had two serum samples analysed within a 6-month interval. When compared with CIE, both ImmunoCap and Platelia Aspergillus IgG had good sensitivity (97 and 93%, respectively) for detection of Aspergillus IgG antibodies. The level of agreement between the two EIAs for positive results was good, but the concentration of antibodies was not correlated between the tests or with CIE titre. ImmunoCap IgG inter-assay coefficient of variation was 5%, whereas Platelia IgG was 33%. Median ImmunoCap IgG values for CPA and allergic aspergillosis were 95 and 32 mg/L, respectively, whereas Platelia IgG values were >80 and 6 AU/mL. The direction of CIE titre change over 6 months was mirrored by ImmunoCap IgG levels in 92% of patients, and by Platelia IgG in 72% of patients. Both ImmunoCap and Platelia Aspergillus IgG EIAs are sensitive measures of Aspergillus IgG antibodies compared with CIE. However, ImmunoCap appears to have better reproducibility and may be more suitable for monitoring patient disease. © 2012 The Authors Clinical Microbiology and Infection © 2012 European Society of Clinical Microbiology and Infectious Diseases.

Evaluation of COBAS AmpliPrep/COBAS TaqMan CMV Test for use in hematopoietic stem cell transplant recipients.

PubMed

Ramanan, Poornima; Razonable, Raymund R

2017-07-01

Cytomegalovirus (CMV) is a common opportunistic infection that contributes to poor outcomes in hematopoietic stem cell transplant (HSCT) recipients. Prevention of CMV end-organ disease in allogeneic HSCT recipients is commonly achieved by preemptive antiviral therapy of asymptomatic CMV reactivation that is detected by serial nucleic acid testing (NAT). However, there was no standardized CMV NAT until the development of the World Health Organization (WHO) International Standard. Areas covered: This article provides a comprehensive review on COBAS AmpliPrep/TaqMan (CAP/CTM) CMV assay (Roche) and emphasizes the limitations in the clinical use of CMV NAT in HSCT recipients. Expert commentary: The CAP/CTM CMV Test is the first US FDA approved commercial quantitative NAT for CMV viral load monitoring of plasma samples in solid organ transplant and HSCT recipients. The CAP/CTM assay has wide linear range of DNA quantification and demonstrates colinearity to the WHO International Standard. Studies of CAP/CTM CMV assay in HSCT recipients are still limited, but are now being reported to define viral thresholds for diagnosis, surveillance and monitoring. Results from these early studies in HSCT recipients suggest that, while the WHO IS has improved the inter-laboratory result variances, there are still important factors that continue to contribute to assay variability. This lack of harmony among NAT highlights the need for further standardization.

The dual effects of root-cap exudates on nematodes: from quiescence in plant-parasitic nematodes to frenzy in entomopathogenic nematodes.

PubMed

Hiltpold, Ivan; Jaffuel, Geoffrey; Turlings, Ted C J

2015-02-01

To defend themselves against herbivores and pathogens, plants produce numerous secondary metabolites, either constitutively or de novo in response to attacks. An intriguing constitutive example is the exudate produced by certain root-cap cells that can induce a state of reversible quiescence in plant-parasitic nematodes, thereby providing protection against these antagonists. The effect of such root exudates on beneficial entomopathogenic nematodes (EPNs) remains unclear, but could potentially impair their use in pest management programmes. We therefore tested how the exudates secreted by green pea (Pisum sativum) root caps affect four commercial EPN species. The exudates induced reversible quiescence in all EPN species tested. Quiescence levels varied with the green pea cultivars tested. Notably, after storage in root exudate, EPN performance traits were maintained over time, whereas performances of EPNs stored in water rapidly declined. In sharp contrast to high concentrations, lower concentrations of the exudate resulted in a significant increase in EPN activity and infectiousness, but still reduced the activity of two plant-parasitic nematode species. Our study suggests a finely tuned dual bioactivity of the exudate from green pea root caps. Appropriately formulated, it can favour long-term storage of EPNs and boost their infectiousness, while it may also be used to protect plants from plant-parasitic nematodes. © The Author 2014. Published by Oxford University Press on behalf of the Society for Experimental Biology.

[Cross-cultural adaptation of the community-acquired pneumonia score questionnaire in patients with mild-to-moderate pneumonia in Colombia].

PubMed

Bernal-Vargas, Mónica Alejandra; Cortés, Jorge Alberto; Sánchez, Ricardo

2017-01-24

One of the strategies for the rational use of antibiotics is the use of the score for community-acquired pneumonia (CAP Score). This instrument clinically evaluates patients with community-acquired pneumonia, thereby facilitating decision making regarding the early and safe withdrawal of antibiotics. To generate a translation and cross-cultural adaptation of the Community-Acquired Pneumonia (CAP) Score questionnaire in Spanish. Authorization for cross-cultural adaptation of the Community-Acquired Pneumonia (CAP) Score questionnaire was obtained; the recommendations of the International Society for Pharmacoeconomics and Outcomes Research (ISPOR) and the European Organisation for Research and Treatment of Cancer (EORTC) were carried out through the following stages: forward translation, reconciliation, backward translation, harmonization, obtaining a provisional questionnaire, and applying the questionnaire in a pilot test. The pilot test was conducted at a second-level public hospital in Bogotá after the study was approved by the ethics and research institutional boards. The changes suggested by the forward translators were applied. There were no discrepancies between the backward and forward translations, consequently, no revisions were necessary. Five items had modifications based on suggestions made by eleven patients hospitalized with a diagnosis of community-acquired pneumonia during the pilot test. A Spanish version of the Community-Acquired Pneumonia (CAP) Score was crossculturally adapted and is now available.