The Study of Cross-layer Optimization for Wireless Rechargeable Sensor Networks Implemented in Coal Mines.

PubMed

Ding, Xu; Shi, Lei; Han, Jianghong; Lu, Jingting

2016-01-28

Wireless sensor networks deployed in coal mines could help companies provide workers working in coal mines with more qualified working conditions. With the underground information collected by sensor nodes at hand, the underground working conditions could be evaluated more precisely. However, sensor nodes may tend to malfunction due to their limited energy supply. In this paper, we study the cross-layer optimization problem for wireless rechargeable sensor networks implemented in coal mines, of which the energy could be replenished through the newly-brewed wireless energy transfer technique. The main results of this article are two-fold: firstly, we obtain the optimal relay nodes' placement according to the minimum overall energy consumption criterion through the Lagrange dual problem and KKT conditions; secondly, the optimal strategies for recharging locomotives and wireless sensor networks are acquired by solving a cross-layer optimization problem. The cyclic nature of these strategies is also manifested through simulations in this paper.

Structural characterization of graphene layers in various Indian coals by X-Ray Diffraction technique

NASA Astrophysics Data System (ADS)

Manoj, B.; Kunjomana, A. G.

2015-02-01

The results of the structural investigation of three Indian coals showed that, the structural parameters like fa & Lc increased where as interlayer spacing d002 decreased with increase in carbon content, aromaticity and coal rank. These structural parameters change just opposite with increase in volatile matter content. Considering the 'turbostratic' structure for coals, the minimum separation between aromatic lamellae was found to vary between 3.34 to 3.61 A° for these coals. As the aromaticity increased, the interlayer spacing decreased an indication of more graphitization of the sample. Volatile matter and carbon content had a strong influence on the aromaticity, interlayer spacing and stacking height on the sample. The average number of carbon atoms per aromatic lamellae and number of layers in the lamellae was found to be 16-21 and 7-8 for all the samples.

Hardened, environmentally disposable composite granules of coal cleaning refuse, coal combustion waste, and other wastes, and method preparing the same

DOEpatents

Burnet, George; Gokhale, Ashok J.

1990-07-10

A hardened, environmentally inert and disposable composite granule of coal cleaning refuse and coal combustion waste, and method for producing the same, wherein the coal combustion waste is first granulated. The coal cleaning refuse is pulverized into fine particles and is then bound, as an outer layer, to the granulated coal combustion waste granules. This combination is then combusted and sintered. After cooling, the combination results in hardened, environmentally inert and disposable composite granules having cores of coal combustion waste, and outer shells of coal cleaning refuse. The composite particles are durable and extremely resistant to environmental and chemical forces.

Hardened, environmentally disposable composite granules of coal cleaning refuse, coal combustion waste, and other wastes, and method preparing the same

DOEpatents

Burnet, G.; Gokhale, A.J.

1990-07-10

A hardened, environmentally inert and disposable composite granule of coal cleaning refuse and coal combustion waste and method for producing the same are disclosed, wherein the coal combustion waste is first granulated. The coal cleaning refuse is pulverized into fine particles and is then bound, as an outer layer, to the granulated coal combustion waste granules. This combination is then combusted and sintered. After cooling, the combination results in hardened, environmentally inert and disposable composite granules having cores of coal combustion waste, and outer shells of coal cleaning refuse. The composite particles are durable and extremely resistant to environmental and chemical forces. 3 figs.

Calculation of dispersion curves and amplitude-depth distributions of Love channel waves in horizontally-layered media. [In seam; various boundary conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rader, D.; Dresen, L.; Ruter, H.

We present dispersion curves, and amplitude-depth distributions of the fundamental and first higher mode of Love seam waves for two characteristic seam models. The first model consists of four layers, representing a coal seam underlain by a root clay of variable thickness. The second model consists of five layers, representing coal seams containing a dirt band with variable position and thickness. The simple three-layer model is used for reference. It is shown that at higher frequencies, depending on the thickness of the root clay and the dirt band, the coal layers alone act as a wave guide, whereas at lowmore » frequencies all layers act together as a channel. Depending on the thickness, and position of the dirt band and the root clay, in the dispersion curves of the group velocity, secondary minima grow in addition to the absolute minima. Furthermore, the dispersion curves of the group velocity of the two modes can overlap. In all these cases, wave groups in addition to the Airy phase of the fundamental mode (propagating with minimum group velocity) occur on the seismograms recorded in in-seam seismic surveys, thus impeding their interpretation. Hence, we suggest the estimation of the dispersion characteristics of Love seam waves in coal seams under investigation preceding actual field surveys. All numerical calculations were performed using a fast and stable phase recursion algorithm.« less

Method and apparatus for measuring surface density of explosive and inert dust in stratified layers

DOEpatents

Sapko, Michael J.; Perlee, Henry E.

1988-01-01

A method for determining the surface density of coal dust on top of rock dust or rock dust on top of coal dust is disclosed which comprises directing a light source at either a coal or rock dust layer overlaying a substratum of the other, detecting the amount of light reflected from the deposit, generating a signal from the reflected light which is converted into a normalized output (V), and calculating the surface density from the normalized output. The surface density S.sub.c of coal dust on top of rock dust is calculated according to the equation: S.sub.c =1/-a.sub.c ln(V) wherein a.sub.c is a constant for the coal dust particles, and the surface density S.sub.r of rock dust on top of coal dust is determined by the equation: ##EQU1## wherein a.sub.r is a constant based on the properties of the rock dust particles. An apparatus is also disclosed for carrying out the method of the present invention.

Identification and classification of high risk groups for Coal Workers' Pneumoconiosis using an artificial neural network based on occupational histories: a retrospective cohort study

PubMed Central

Liu, Hongbo; Tang, Zhifeng; Yang, Yongli; Weng, Dong; Sun, Gao; Duan, Zhiwen; Chen, Jie

2009-01-01

Background Coal workers' pneumoconiosis (CWP) is a preventable, but not fully curable occupational lung disease. More and more coal miners are likely to be at risk of developing CWP owing to an increase in coal production and utilization, especially in developing countries. Coal miners with different occupational categories and durations of dust exposure may be at different levels of risk for CWP. It is necessary to identify and classify different levels of risk for CWP in coal miners with different work histories. In this way, we can recommend different intervals for medical examinations according to different levels of risk for CWP. Our findings may provide a basis for further emending the measures of CWP prevention and control. Methods The study was performed using longitudinal retrospective data in the Tiefa Colliery in China. A three-layer artificial neural network with 6 input variables, 15 neurons in the hidden layer, and 1 output neuron was developed in conjunction with coal miners' occupational exposure data. Sensitivity and ROC analyses were adapted to explain the importance of input variables and the performance of the neural network. The occupational characteristics and the probability values predicted were used to categorize coal miners for their levels of risk for CWP. Results The sensitivity analysis showed that influence of the duration of dust exposure and occupational category on CWP was 65% and 67%, respectively. The area under the ROC in 3 sets was 0.981, 0.969, and 0.992. There were 7959 coal miners with a probability value < 0.001. The average duration of dust exposure was 15.35 years. The average duration of ex-dust exposure was 0.69 years. Of the coal miners, 79.27% worked in helping and mining. Most of the coal miners were born after 1950 and were first exposed to dust after 1970. One hundred forty-four coal miners had a probability value ≥0.1. The average durations of dust exposure and ex-dust exposure were 25.70 and 16.30 years, respectively. Most of the coal miners were born before 1950 and began to be exposed to dust before 1980. Of the coal miners, 90.28% worked in tunneling. Conclusion The duration of dust exposure and occupational category were the two most important factors for CWP. Coal miners at different levels of risk for CWP could be classified by the three-layer neural network analysis based on occupational history. PMID:19785771

Coal Thickness Gauging Using Elastic Waves

NASA Technical Reports Server (NTRS)

Nazarian, Soheil; Bar-Cohen, Yoseph

1999-01-01

The efforts of a mining crew can be optimized, if the thickness of the coal layers to be excavated is known before excavation. Wave propagation techniques can be used to estimate the thickness of the layer based on the contrast in the wave velocity between coal and rock beyond it. Another advantage of repeated wave measurement is that the state of the stress within the mine can be estimated. The state of the stress can be used in many safety-related decisions made during the operation of the mine. Given these two advantages, a study was carried out to determine the feasibility of the methodology. The results are presented herein.

Soil organic carbon and nitrogen accumulation on coal mine spoils reclaimed with maritime pine (Pinus pinaster Aiton) in Agacli-Istanbul.

PubMed

Sever, Hakan; Makineci, Ender

2009-08-01

Mining operations on open coal mines in Agacli-Istanbul have resulted in the destruction of vast amounts of land. To rehabilitate these degraded lands, plantations on this area began in 1988. Twelve tree species were planted, however, the most planted tree species was maritime pine (Pinus pinaster Aiton). This study performed on 14 sample plots randomly selected in maritime pine plantations on coal mine soil/spoils in 2005. Soil samples were taken from eight different soil layers (0-1, 1-3, 3-5, 5-10, 10-20, 20-30, 30-40 and 40-50 cm) into the soil profile. On soil samples; fine soil fraction (<2 mm), soil acidity (pH), organic carbon (C(org)) and total nitrogen (N(t)) contents were investigated, and results were compared statistically among soil layers. As a result, 17 years after plantations, total forest floor accumulation determined as 17,973.20 kg ha(-1). Total nitrogen and organic matter amounts of forest floor were 113.90 and 14,640.92 kg ha(-1) respectively. Among soil layers, the highest levels of organic carbon (1.77%) and total nitrogen (0.096%) and the lowest pH value (pH 5.38) were found in 0-1 cm soil layer, and the variation differs significantly among soil layers. Both organic carbon and total nitrogen content decreased, pH values increased from 0-1 to 5-10 cm layer. In conclusion, according to results obtained maritime pine plantations on coal mine spoils; slow accumulation and decomposition of forest floor undergo simultaneously. Depending on these changes organic carbon and total nitrogen contents increased in upper layer of soil/spoil.

Development of low-ash, planar peat swamps in an alluvial-plain setting: The no. 5 Block beds (westphalian D) of southern West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Staub, J.R.; Richards, B.K.

1993-07-01

Coals from the No. 5 Block coal beds (Westphalian D) of the central Appalachian basin are noted for their blocky, dull character and their low ash and low sulfur content. The beds are multiple benched, with rock partings separating benches. Individual benches have limited lateral extent and, where thick, are dominated by bright, high-ash coal at the base and dull, low-ash coal in the upper parts. The duller coals contain more exinite-group and inertinite-group macerals than the brighter coals. These coal beds are encased in sandstone units dominated by fining-upward sequences. The overall depositional setting is an alluvial-plain environment withmore » northwest-flowing channels spaced approximately 20 km apart. The channels were flanked by clastic swamps about 7 km wide. Low-ash peat accumulated in areas of the flood plain most distant from the channels. These peat-accumulating swamps were about 8 km across. In a few instances low-frequency flood events introduced fine siliciclastic sediment into the peat swamps, depositing a thin layer of sediment on top of the peat. This sediment layer is thicker where the underlying coal is the thickest. These thick coal areas are topographically lower than surrounding coal areas. This relationship between coal thickness, parting thickness, and topography indicates that these peat swamps were planar at the time of deposition. Individual coal benches contain abundant preserved cellular tissue (telocollinite, semifusinite, and fusinite) at most locations, suggesting that robust vegetation was widespread in the swamps and that the morphology was planar. The high concentrations of exinite-group an inertinite-group macerals in the upper parts of benches resulted from selective decomposition and oxidation of the peat in subaerial and aquatic planar-swamp environments.« less

Occurrence of microbial acetate-oxidation in ~2 km-deep coal-bearing sediments off the Shimokita Peninsula, Japan (IODP Expedition 337)

NASA Astrophysics Data System (ADS)

Ijiri, A.; Inagaki, F.

2015-12-01

During the Integrated Ocean Drilling Program (IODP) Expedition 337 in 2012, the riser-drilling vessel Chikyu extended the previous world depth record of scientific ocean drilling and made one of the deepest scientific borehole down to 2466 m below the seafloor (mbsf) at Site C0020 Hole A off the Shimokita Peninsula, Japan. The sedimentary sequence consists of 17 lignite layers below 1.5 km bellow the seafloor. Microbiological and geochemical data consistently showed evidence for the existence of microbial communities associated with lignite coal beds in the coal-bearing sediments (Inagaki and Hinrichs et al., Science, 2015). Since lignite coals produce substantial dissolved organic compounds during the burial alternation process, volatile fatty acids may play important roles for microbial life and its activity in the deep sedimentary environment. To address this hypothesis, we measured methanogenic and acetate-oxidation activities by radiotracer incubation experiments using 14C-labelled substrate ([2-14C]-acetate) immediately after core recovery. Activity of aceticlastic methanogenesis was observed in the sediment above the coal-baring layers (>1990 mbsf), ranging from 0.2 to 1.2 pmol cm-3 d-1. The highest activity was observed in a coal-bed horizon at 1990 mbsf. However, aceticlastic methanogenesis was below the detection limit in sediment samples below the 2 km-coal layers. Activity of acetate oxidation to CO2 was measured by 14CO2 production rate from [2-14C]-acetate. Interestingly, the acetate-oxidation activity was observed in sediments above the coal beds, which values were generally higher than those of methanogenesis with the maximum value of 33 pmol cm-3 d-1 at 1800 mbsf. The rates gradually decreased with increasing depth from 1800 mbsf and reached below the detection limit (i.e., 0.05 pmol cm-3 d-1) in 2 km-deep coal-bed samples. The occurrence of relatively high acetate oxidation at ~1800 mbsf above the coal formation suggests that microbes respire acetate with available electron acceptors such as glauconitic iron oxides in the deep sedimentary environment.

Heat and mass transfer at gas-phase ignition of grinded coal layer by several metal particles heated to a high temperature

NASA Astrophysics Data System (ADS)

Glushkov, D. O.; Kuznetsov, G. V.; Strizhak, P. A.

2017-07-01

Characteristics of gas-phase ignition of grinded brown coal (brand 2B, Shive-Ovoos deposit in Mongolia) layer by single and several metal particles heated to a high temperature (above 1000 K) have been investigated numerically. The developed mathematical model of the process takes into account the heating and thermal decomposition of coal at the expense of the heat supplied from local heat sources, release of volatiles, formation and heating of gas mixture and its ignition. The conditions of the joint effect of several hot particles on the main characteristic of the process-ignition delay time are determined. The relation of the ignition zone position in the vicinity of local heat sources and the intensity of combustible gas mixture warming has been elucidated. It has been found that when the distance between neighboring particles exceeds 1.5 hot particle size, an analysis of characteristics and regularities of coal ignition by several local heat sources can be carried out within the framework of the model of "single metal particle / grinded coal / air". Besides, it has been shown with the use of this model that the increase in the hot particle height leads, along with the ignition delay time reduction, to a reduction of the source initial temperatures required for solid fuel ignition. At an imperfect thermal contact at the interface hot particle / grinded coal due to the natural porosity of the solid fuel structure, the intensity of ignition reduces due to a less significant effect of radiation in the area of pores on the heat transfer conditions compared to heat transfer by conduction in the near-surface coal layer without regard to its heterogeneous structure.

Modeling forest ecosystem changes resulting from surface coal mining in West Virginia

Treesearch

John Brown; Andrew J. Lister; Mary Ann Fajvan; Bonnie Ruefenacht; Christine Mazzarella

2012-01-01

The objective of this project is to assess the effects of surface coal mining on forest ecosystem disturbance and restoration in the Coal River Subbasin in southern West Virginia. Our approach is to develop disturbance impact models for this subbasin that will serve as a case study for testing the feasibility of integrating currently available GIS data layers, remote...

Coal thickness guage using RRAS techniques, parts 2 and 3

NASA Technical Reports Server (NTRS)

King, J. D.; Rollwitz, W. L.

1980-01-01

Electron magnetic resonance was investigated as a sensing technique for use in measuring the thickness of the layer of coal overlying the rock substrate. The goal is development of a thickness gauge which will be usable for control of mining machinery to maintain the coal thickness within selected bounds. A sensor must be noncontracting, have a measurement range of 6 inches or more, and an accuracy of 1/2 inch or better. The sensor should be insensitive to variations in spacing between the sensor and the surface, the response speed should be adequate to permit use on continuous mining equipment, and the device should be rugged and otherwise suited for operation under conditions of high vibration, moisture, and dust. Finally, the sensor measurement must not be adversely affected by the natural effects occurring in coal such as impurities, voids, cracks, layering, high moisture level, and other conditions that are likely to be encountered.

Variability of Mercury Content in Coal Matter From Coal Seams of The Upper Silesia Coal Basin

NASA Astrophysics Data System (ADS)

Wierzchowski, Krzysztof; Chećko, Jarosław; Pyka, Ireneusz

2017-12-01

The process of identifying and documenting the quality parameters of coal, as well as the conditions of coal deposition in the seam, is multi-stage and extremely expensive. The taking and analyzing of seam samples is the method of assessment of the quality and quantity parameters of coals in deep mines. Depending on the method of sampling, it offers quite precise assessment of the quality parameters of potential commercial coals. The main kind of seam samples under consideration are so-called "documentary seam samples", which exclude dirt bands and other seam contaminants. Mercury content in coal matter from the currently accessible and exploited coal seams of the Upper Silesian Coal Basin (USCB) was assessed. It was noted that the mercury content in coal seams decreases with the age of the seam and, to a lesser extent, seam deposition depth. Maps of the variation of mercury content in selected lithostratigraphic units (layers) of the Upper Silesian Coal Basin have been created.

Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

NASA Astrophysics Data System (ADS)

Borowski, Marek; Kuczera, Zbigniew

2018-03-01

Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on numerous factors; mainly on presence or lack of insulating layers in cover deposit that allow or do not on degasification and easily methane outflow into surroundings. Hence in coal mining there are coal deposits that contain only low degree of methane saturation in places where is lack of insulating layers till high in methane coal deposits occurring in insulating claystones or in shales. Conducting mining works in coal deposits of high methane hazard without using of special measures to combat (ventilation, methane drainage) could be impossible. Control of methane hazard depends also on other co-occuring natural dangers for which used preventive actions eliminate methane hazard. Safety in mines excavating coal deposits saturated with methane depends on the correct estimation of methane hazard, drawn up forecasts, conducted observations, hazard control as well as undertaken prevention measures. Methane risk prevention includes identification and control methods of methane hazards as well as means of combating the explosive accumulation of methane in longwall workings. The main preventive actions in underground coal mines are: effective ventilation that prevents forming of methane fuses or placed methane accumulation in headings ventilated by airflow created by main fans and in headings with auxiliary ventilation, methane drainage using drain holes that are drilled from underground headings or from the surface, methanometry control of methane concentration in the air; location of the sensors is defined by law, additional ventilation equipment used in places of lower intensity of ventilation and places where methane is concentrated.

Graphene quantum dots, graphene oxide, carbon quantum dots and graphite nanocrystals in coals

NASA Astrophysics Data System (ADS)

Dong, Yongqiang; Lin, Jianpeng; Chen, Yingmei; Fu, Fengfu; Chi, Yuwu; Chen, Guonan

2014-06-01

Six coal samples of different ranks have been used to prepare single-layer graphene quantum dots (S-GQDs). After chemical oxidation and a series of centrifugation separation, every coal could be treated into two fractions, namely, CoalA and CoalB. According to the characterization results of TEM, AFM, XRD, Raman and FTIR, CoalA was revealed to be mainly composed of S-GQDs, which have an average height of about 0.5 nm and an average plane dimension of about 10 nm. The obtained S-GQDs showed excitation-dependent fluorescence and excellent electrochemiluminescence. CoalB was found to be some other carbon-based nanomaterials (CNMs), including agglomerated GQDs, graphene oxide, carbon quantum dots and agglomerated carbon nanocrystals. Generally, low-ranked coals might be more suitable for the preparation of S-GQDs. The production yield of S-GQDs from the six investigated coals decreased from 56.30% to 14.66% when the coal rank increased gradually. In contrast, high-ranked coals had high production yield of CoalB and might be more suitable for preparing other CNMs that were contained in CoalB, although those CNMs were difficult to separate from each other in our experiment.Six coal samples of different ranks have been used to prepare single-layer graphene quantum dots (S-GQDs). After chemical oxidation and a series of centrifugation separation, every coal could be treated into two fractions, namely, CoalA and CoalB. According to the characterization results of TEM, AFM, XRD, Raman and FTIR, CoalA was revealed to be mainly composed of S-GQDs, which have an average height of about 0.5 nm and an average plane dimension of about 10 nm. The obtained S-GQDs showed excitation-dependent fluorescence and excellent electrochemiluminescence. CoalB was found to be some other carbon-based nanomaterials (CNMs), including agglomerated GQDs, graphene oxide, carbon quantum dots and agglomerated carbon nanocrystals. Generally, low-ranked coals might be more suitable for the preparation of S-GQDs. The production yield of S-GQDs from the six investigated coals decreased from 56.30% to 14.66% when the coal rank increased gradually. In contrast, high-ranked coals had high production yield of CoalB and might be more suitable for preparing other CNMs that were contained in CoalB, although those CNMs were difficult to separate from each other in our experiment. Electronic supplementary information (ESI) available: Elemental analysis results of coal samples, FTIR spectra of CoalA and CoalB, ECL responses of CoalA/S2O82-. See DOI: 10.1039/c4nr01482k

Sensitivity Analysis of Mechanical Parameters of Different Rock Layers to the Stability of Coal Roadway in Soft Rock Strata

PubMed Central

Zhao, Zeng-hui; Wang, Wei-ming; Gao, Xin; Yan, Ji-xing

2013-01-01

According to the geological characteristics of Xinjiang Ili mine in western area of China, a physical model of interstratified strata composed of soft rock and hard coal seam was established. Selecting the tunnel position, deformation modulus, and strength parameters of each layer as influencing factors, the sensitivity coefficient of roadway deformation to each parameter was firstly analyzed based on a Mohr-Columb strain softening model and nonlinear elastic-plastic finite element analysis. Then the effect laws of influencing factors which showed high sensitivity were further discussed. Finally, a regression model for the relationship between roadway displacements and multifactors was obtained by equivalent linear regression under multiple factors. The results show that the roadway deformation is highly sensitive to the depth of coal seam under the floor which should be considered in the layout of coal roadway; deformation modulus and strength of coal seam and floor have a great influence on the global stability of tunnel; on the contrary, roadway deformation is not sensitive to the mechanical parameters of soft roof; roadway deformation under random combinations of multi-factors can be deduced by the regression model. These conclusions provide theoretical significance to the arrangement and stability maintenance of coal roadway. PMID:24459447

Dissolved organic matter removal during coal slag additive soil aquifer treatment for secondary effluent recharging: Contribution of aerobic biodegradation.

PubMed

Wei, Liangliang; Li, Siliang; Noguera, Daniel R; Qin, Kena; Jiang, Junqiu; Zhao, Qingliang; Kong, Xiangjuan; Cui, Fuyi

2015-06-01

Recycling wastewater treatment plant (WWTP) effluent at low cost via the soil aquifer treatment (SAT), which has been considered as a renewable approach in regenerating potable and non-potable water, is welcome in arid and semi-arid regions throughout the world. In this study, the effect of a coal slag additive on the bulk removal of the dissolved organic matter (DOM) in WWTP effluent during SAT operation was explored via the matrix configurations of both coal slag layer and natural soil layer. Azide inhibition and XAD-resins fractionation experiments indicated that the appropriate configuration designing of an upper soil layer (25 cm) and a mixture of soil/coal slag underneath would enhance the removal efficiency of adsorption and anaerobic biodegradation to the same level as that of aerobic biodegradation (31.7% vs 32.2%), while it was only 29.4% compared with the aerobic biodegradation during traditional 50 cm soil column operation. The added coal slag would preferentially adsorb the hydrophobic DOM, and those adsorbed organics could be partially biodegraded by the biomass within the SAT systems. Compared with the relatively lower dissolved organic carbon (DOC), ultraviolet light adsorption at 254 nm (UV-254) and trihalomethane formation potential (THMFP) removal rate of the original soil column (42.0%, 32.9%, and 28.0%, respectively), SSL2 and SSL4 columns would enhance the bulk removal efficiency to more than 60%. Moreover, a coal slag additive in the SAT columns could decline the aromatic components (fulvic-like organics and tryptophan-like proteins) significantly. Copyright © 2015 Elsevier Ltd. All rights reserved.

Low ash, planar peat swamp development in an alluvial plain setting: The No. 5 block beds of southern West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Staub, J.R.; Richards, B.K.

1992-01-01

Coals from the No. 5 Block beds (Westphalian D) are noted for their low ash and sulfur content. Beds are multiple benched, with rock partings separating individual benches. Benches have limited continuity and, where thick are dominated by bright, high ash coal at the base and dull, low ash coal in their upper portions. The duller coals contain more exinite and inertinite group macerals than the brighter coals. The depositional setting is an alluvial plain environment with channel systems separated by distances of about 20 km. The channel systems were flanked by clastic swamps for distances of up to 7more » km or more on either side. Areas of flood plain most distant from the channels were sites where peat accumulated and these zones were about 8 km across. High energy, low frequency flood events introduced fine grained sediment into the peat swamps resulting in thin layers of sediment being deposited on top of the peat. These sediment layers are thicker in areas where the underlying coal is the thickest. These thick coal areas are topographically negative. This relationship between coal and parting thickness and topography indicates that these peat swamps were low-lying or planar. Individual coal benches contain abundant amounts of preserved cellular tissue (telocollinite, semifusinite, fusinite) at most locations indicating that woody arborescent like vegetation was widespread in the swamps suggesting a planar morphology. The high concentrations of exinite and inertinite group macerals found in the upper portions of individual benches resulted from decomposition and oxidation of the peat in subaerial to aquatic planar swamp environments.« less

Geospatial data for coal beds in the Powder River Basin, Wyoming and Montana

USGS Publications Warehouse

Kinney, Scott A.; Scott, David C.; Osmonson, Lee M.; Luppens, James A.

2015-01-01

The purpose of this report is to provide geospatial data for various layers and themes in a Geographic Information System (GIS) format for the Powder River Basin, Wyoming and Montana. In 2015, as part of the U.S. Coal Resources and Reserves Assessment Project, the U.S. Geological Survey (USGS) completed an assessment of coal resources and reserves within the Powder River Basin, Wyoming and Montana. This report is supplemental to USGS Professional Paper 1809 and contains GIS data that can be used to view digital layers or themes, including the Tertiary limit of the Powder River Basin boundary, locations of drill holes, clinker, mined coal, land use and technical restrictions, geology, mineral estate ownership, coal thickness, depth to the top of the coal bed (overburden), and coal reliability categories. Larger scale maps may be viewed using the GIS data provided in this report supplemental to the page-size maps provided in USGS Professional Paper 1809. Additionally, these GIS data can be exported to other digital applications as needed by the user. The database used for this report contains a total of 29,928 drill holes, of which 21,393 are in the public domain. The public domain database is linked to the geodatabase in this report so that the user can access the drill-hole data through GIS applications. Results of this report are available at the USGS Energy Resources Program Web site,http://energy.usgs.gov/RegionalStudies/PowderRiverBasin.aspx.

Determination of Critical Conditions of Spontaneous Combustion of Coal in Longwall Gob Areas / Wyznaczanie Warunków Krytycznych Samozapalania Węgla W Zrobach Ścian

NASA Astrophysics Data System (ADS)

Cygankiewicz, Janusz

2015-09-01

Decades of experience in the fight against endogenous fire hazard in coal mines indicate a major influence of certain conditions in a given area of the mine on the possibility of fire occurrence, such as: susceptibility of coals to spontaneous combustion, oxygen content in the air incoming to the self-heating coal, conditions of heat exchange between the self-heating coal mass and the environment This paper presents a numerical method for determining the critical conditions of spontaneous combustion of coal in longwall gob areas, i.e. conditions under which spontaneous combustion may occur. It has been assumed that crushed coal in the gob has a shape of a flat layer adjacent from the roof and floor side to the rocks. Our considerations have been limited to coals containing small amount of moisture. A simple model of oxidation kinetics on the coal surface expressed by the Arrhenius equation has been adopted. This model assumes that oxidation rate is independent of the amount of oxygen absorbed by coal. The rate of reaction depends only on temperature, with the parameters of the equation changing after the coal has reached the critical temperature. The article presents also a mathematical model of spontaneous heating of the coal layer in the gob area. It describes the heat balance in the coal as well as the oxygen and heat balance in the flowing gases. The model consists of a system of differential equations which are solved using numerical techniques. The developed computer program enables to perform the relevant calculations. In this paper, on the example of coal from a seam 405, we present the method for determining the following critical parameters of the layer of crushed coal: thickness of the layer, oxygen content in a stream of gases flowing through the layer and thermal conductivity of surrounding rocks. Wieloletnie doświadczenie w zakresie zwalczania zagrożenia pożarem endogenicznym w kopalniach wskazują na zasadniczy wpływ na możliwość zaistnienia pożaru niektórych warunków panujących w danym miejscu kopalni, takich jak: - skłonność węgla do samozapalania - zawartość tlenu w powietrzu dopływającym do zagrzewającego się węgla. W pracy przedstawiono numeryczną metodę wyznaczania warunków krytycznych samozapalania węgla w zrobach ścian, czyli takich po spełnieniu których może dojść do samozapalenia. Przyjęto, że znajdujący się w zrobach rozkruszony węgiel ma kształt płaskiej warstwy, sąsiadującej od stropu i spągu ze skałami. Rozważania ograniczono do węgli charakteryzujących się niską zawartością wilgoci. Przyjęto prosty model kinetyki utleniania na powierzchni węgla wyrażony równaniem Arrheniusa. Model ten zakłada niezależność szybkości utleniania od ilości tlenu pochłoniętego przez węgiel. Szybkość reakcji zależy jedynie od temperatury , przy czym występujące w równaniu parametry zmieniają się po osiągnięciu przez węgiel temperatury krytycznej. W artykule przedstawiono matematyczny model samozagrzewania warstwy węgla w zrobach opisujący bilans ciepła w węglu oraz bilans tlenu i bilans ciepła w przepływających gazach. Tworzące model układy równań różniczkowych cząstkowych rozwiązywane są metodami numerycznymi. Opracowany program komputerowy umożliwia wykonywanie stosownych obliczeń. W pracy, na przykładzie węgla z pokładu 405 , przedstawiono sposób wyznaczania warunków krytycznych warstwy rozkruszonego węgla: grubości warstwy, zawartości tlenu w przepływających przez warstwę gazach oraz przewodności cieplnej otaczających skał.

Bidirectional, Automatic Coal-Mining Machine

NASA Technical Reports Server (NTRS)

Collins, Earl R., Jr.

1986-01-01

Proposed coal-mining machine operates in both forward and reverse directions along mine face. New design increases efficiency and productivity, because does not stop cutting as it retreats to starting position after completing pass along face. To further increase efficiency, automatic miner carries its own machinery for crushing coal and feeding it to slurry-transport tube. Dual-drum mining machine cuts coal in two layers, crushes, mixes with water, and feeds it as slurry to haulage tube. At end of pass, foward drum raised so it becomes rear drum, and rear drum lowered, becoming forward drum for return pass.

Coal thickness gauge using RRAS techniques, part 1. [radiofrequency resonance absorption

NASA Technical Reports Server (NTRS)

Rollwitz, W. L.; King, J. D.

1978-01-01

A noncontacting sensor having a measurement range of 0 to 6 in or more, and with an accuracy of 0.5 in or better is needed to control the machinery used in modern coal mining so that the thickness of the coal layer remaining over the rock is maintained within selected bounds. The feasibility of using the radiofrequency resonance absorption (RRAS) techniques of electron magnetic resonance (EMR) and nuclear magnetic resonance (NMR) as the basis of a coal thickness gauge is discussed. The EMR technique was found, by analysis and experiments, to be well suited for this application.

The role of coal in industrialization: A case study of Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akarakiri, J.B.

1989-01-01

Coal is a mineral matter found in layers or beds in sedimentary rocks. It is a very highly variable substance. In addition to the variations from lignite to bituminous and anthracite, there are vast differences in its heating value, amount of volatiles, sulfur, moisture and so on. The chemical and physical properties of coal make it an important industrial raw material. There is proven 639 million tonnes of coal reserves in Nigeria. This paper examines the potential and current role of coal in the industrialization of Nigeria. Industries are now dependent on fuel oil as a source of fuel becausemore » of its economic and technological advantages over coal. Coal is a source of industrial energy for the future after the known oil reserves might have been exhausted. In the short term, coal can be used as a material for chemicals, iron and steel production as well as a substitute for wood energy in the process of industrialization.« less

The Eocene Thermal Maximum 2 (ETM-2) in a terrestrial section of the High Arctic: identification by U-Pb zircon ages of volcanic ashes and carbon isotope records of coal and amber (Stenkul Fiord, Ellesmere Island, Canada)

NASA Astrophysics Data System (ADS)

Reinhardt, Lutz; von Gosen, Werner; Piepjohn, Karsten; Lückge, Andreas; Schmitz, Mark

2017-04-01

The Stenkul Fiord section on southern Ellesmere Island reveals largely fluvial clastic sediments with intercalated coal seams of the Margaret Formation of Late Paleocene/Early Eocene age according to palynology and vertebrate remains. Field studies in recent years and interpretative mapping of a high-resolution satellite image of the area southeast of Stenkul Fiord revealed that the clastic deposits consist of at least four sedimentary units (Units 1 to 4) separated by unconformities. Several centimeter-thin volcanic ash layers, recognized within coal layers and preserved as crandallite group minerals (Ca-bearing goyazite), suggest an intense volcanic ash fall activity. Based on new U-Pb zircon ages (ID-TIMS) of three ash layers, the volcanic ash fall took place at 53.7 Ma in the Early Eocene, i.e. within the Eocene Thermal Maximum 2 (ETM-2) hyperthermal. The ETM-2 is bracketed further by discrete negative excursions of carbon isotope records of both bulk coal and amber droplets collected from individual coal layers of the section. The identification of the ETM-2 hyperthermal provides a stratigraphic tie-point in the terrestrial Margaret Formation sediments enabling assignment of the lowermost sedimentary Unit 1 to the Late Paleocene-earliest Eocene, Unit 2 to the Early Eocene, whereas Unit 3 and 4 might be Early to Middle Eocene in age. Thus the timing of syn-sedimentary movements of the Eurekan deformation causal for the observed unconformities in the section can be studied and the positions of further hyperthermals like the PETM or the ETM-3 in the section can be identified in the future. The integration of structural studies, new U-Pb zircon ages, and different carbon isotope records provides a new stratigraphic framework for further examination of the unique Early Eocene flora and fauna preserved in this high-latitude outcrop.

Investigation of Corrosion Protection in Oil Mineral Reservoirs by Nanocomposites Used as Coating Layers

NASA Astrophysics Data System (ADS)

Al-Sarraf, Abdulhameed R.; Al-Saaidi, Samer A.

2018-05-01

In this study, a number of nanocomposites were prepared by adding magnesium oxide (MgO) with weight percentages (1, 2 & 3)% to cellulose nitrate and sodium silicate as an intermediate layer and other nanocomposites by adding MgO, coal coke and hybrid (MgO & coal coke with ratio 1:1) with weight percentages (1, 2 & 3)% to epoxy resin as final layer. The identity of the used metal is determined by spectrometer OE thermo. The nature and topography of the surface layers were examined by optical microscope and atomic force microscope (AFM). Mechanical properties are indicated by hardness, wear rate, impact strength and adhesion strength. The efficiency of the layers prepared to inhibit corrosion in the oil mineral reservoirs of the oil products distribution company was studied by electrochemical corrosion test in addition to the chemical corrosion test. The used metal is (St-37) according to (ASTM). It was found that the best intermediate layer (cellulose nitrate+3%MgO) and the final layer is the epoxy resin reinforced by 2% hybrid.

A New Approach in Coal Mine Exploration Using Cosmic Ray Muons

NASA Astrophysics Data System (ADS)

Darijani, Reza; Negarestani, Ali; Rezaie, Mohammad Reza; Fatemi, Syed Jalil; Akhond, Ahmad

2016-08-01

Muon radiography is a technique that uses cosmic ray muons to image the interior of large scale geological structures. The muon absorption in matter is the most important parameter in cosmic ray muon radiography. Cosmic ray muon radiography is similar to X-ray radiography. The main aim in this survey is the simulation of the muon radiography for exploration of mines. So, the production source, tracking, and detection of cosmic ray muons were simulated by MCNPX code. For this purpose, the input data of the source card in MCNPX code were extracted from the muon energy spectrum at sea level. In addition, the other input data such as average density and thickness of layers that were used in this code are the measured data from Pabdana (Kerman, Iran) coal mines. The average thickness and density of these layers in the coal mines are from 2 to 4 m and 1.3 gr/c3, respectively. To increase the spatial resolution, a detector was placed inside the mountain. The results indicated that using this approach, the layers with minimum thickness about 2.5 m can be identified.

Prediction of groundwater inrush into coal mines from aquifers underlying the coal seams in China: application of vulnerability index method to Zhangcun Coal Mine, China

NASA Astrophysics Data System (ADS)

Wu, Qiang; Zhou, Wanfang; Wang, Jinhua; Xie, Shuhan

2009-05-01

Groundwater inrush is a geohazard that can significantly impact safe operations of the coal mines in China. Its occurrence is controlled by many factors and processes are often not amenable to mathematical expressions. To evaluate the water inrush risk, Professor Wu and his colleagues have proposed the vulnerability index approach by coupling the artificial neural network (ANN) and geographic information system (GIS). The detailed procedures of using this innovative approach are shown in a case study. Firstly, the powerful spatial data analysis functions of GIS was used to establish the thematic layer of each of the main factors that control the water inrush, and then to choose the training sample on the thematic layer with the ANN-BP Arithmetic. Secondly, the ANN evaluation model of the water inrush was established to determine the threshold value for each risk level with a histogram of the water inrush vulnerability index. As a result, the mine area was divided into four regions with different vulnerability levels and they served as the general guidelines for the mine operations.

Synergistic erosion/corrosion of superalloys in PFB coal combustor effluent

NASA Technical Reports Server (NTRS)

Benford, S. M.; Zellars, G. R.; Lowell, C. E.

1981-01-01

Two Ni-based superalloys were exposed to the high velocity effluent of a pressurized fluidized bed coal combustor. Targets were 15 cm diameter rotors operating at 40,000 rpm and small flat plate specimens. Above an erosion rate threshold, the targets were eroded to bare metal. The presence of accelerated oxidation at lower erosion rates suggests erosion/corrosion synergism. Various mechanisms which may contribute to the observed oxide growth enhancement include erosive removal of protective oxide layers, oxide and subsurface cracking, and chemical interaction with sulfur in the gas and deposits through damaged surface layers.

Monte Carlo simulation of moderator and reflector in coal analyzer based on a D-T neutron generator.

PubMed

Shan, Qing; Chu, Shengnan; Jia, Wenbao

2015-11-01

Coal is one of the most popular fuels in the world. The use of coal not only produces carbon dioxide, but also contributes to the environmental pollution by heavy metals. In prompt gamma-ray neutron activation analysis (PGNAA)-based coal analyzer, the characteristic gamma rays of C and O are mainly induced by fast neutrons, whereas thermal neutrons can be used to induce the characteristic gamma rays of H, Si, and heavy metals. Therefore, appropriate thermal and fast neutrons are beneficial in improving the measurement accuracy of heavy metals, and ensure that the measurement accuracy of main elements meets the requirements of the industry. Once the required yield of the deuterium-tritium (d-T) neutron generator is determined, appropriate thermal and fast neutrons can be obtained by optimizing the neutron source term. In this article, the Monte Carlo N-Particle (MCNP) Transport Code and Evaluated Nuclear Data File (ENDF) database are used to optimize the neutron source term in PGNAA-based coal analyzer, including the material and shape of the moderator and neutron reflector. The optimized targets include two points: (1) the ratio of the thermal to fast neutron is 1:1 and (2) the total neutron flux from the optimized neutron source in the sample increases at least 100% when compared with the initial one. The simulation results show that, the total neutron flux in the sample increases 102%, 102%, 85%, 72%, and 62% with Pb, Bi, Nb, W, and Be reflectors, respectively. Maximum optimization of the targets is achieved when the moderator is a 3-cm-thick lead layer coupled with a 3-cm-thick high-density polyethylene (HDPE) layer, and the neutron reflector is a 27-cm-thick hemispherical lead layer. Copyright © 2015 Elsevier Ltd. All rights reserved.

New technological methods for protecting underground waters from agricultural pollution

NASA Astrophysics Data System (ADS)

Mavlyanov, Gani

2015-04-01

The agricultural production on the irrigated grounds can not carry on without mineral fertilizers, pesticides and herbicides. Especially it is shown in Uzbekistan, in cultivation of cotton. There is an increase in mineralization, rigidity, quantity of heavy metals, phenols and other pollutions in the cotton fields. Thus there is an exhaustion of stocks of fresh underground waters. In the year 2003 we were offered to create the ecological board to prevent pollution to get up to a level of subsoil waters in the top 30 centimeter layer of the ground. We carried out an accumulation and pollution processing. This layer possesses a high adsorbing ability for heavy metals, mineral oil, mineral fertilizers remnants, defoliants and pesticides. In order to remediate a biological pollution treatment processing should be take into account. The idea is consisted in the following. The adsorption properties of coal is all well-known that the Angren coal washing factories in Tashkent area have collected more than 10 million tons of the coal dust to mix with clays. We have picked up association of anaerobic microorganisms which, using for development, destroys nutrients of coal waste pollutions to a harmless content for people. Coal waste inoculation also are scattered by these microorganisms on the field before plowing. Deep (up to 30 cm) plowing brings them on depth from 5 up to 30 cm. Is created by a plough a layer with necessary protective properties. The norm of entering depends on the structure of ground and the intensity of pollutions. Laboratory experiments have shown that 50% of pollutions can be treated by the ecological board and are processed up to safe limit.

Estimating Effective Seismic Anisotropy Of Coal Seam Gas Reservoirs from Sonic Log Data Using Orthorhombic Buckus-style Upscaling

NASA Astrophysics Data System (ADS)

Gross, Lutz; Tyson, Stephen

2015-04-01

Fracture density and orientation are key parameters controlling productivity of coal seam gas reservoirs. Seismic anisotropy can help to identify and quantify fracture characteristics. In particular, wide offset and dense azimuthal coverage land seismic recordings offers the opportunity for recovery of anisotropy parameters. In many coal seam gas reservoirs (eg. Walloon Subgroup in the Surat Basin, Queensland, Australia (Esterle et al. 2013)) the thickness of coal-beds and interbeds (e.g mud-stone) are well below the seismic wave length (0.3-1m versus 5-15m). In these situations, the observed seismic anisotropy parameters represent effective elastic properties of the composite media formed of fractured, anisotropic coal and isotropic interbed. As a consequence observed seismic anisotropy cannot directly be linked to fracture characteristics but requires a more careful interpretation. In the paper we will discuss techniques to estimate effective seismic anisotropy parameters from well log data with the objective to improve the interpretation for the case of layered thin coal beds. In the first step we use sonic log data to reconstruct the elasticity parameters as function of depth (at the resolution of the sonic log). It is assumed that within a sample fractures are sparse, of the same size and orientation, penny-shaped and equally spaced. Following classical fracture model this can be modeled as an elastic horizontally transversely isotropic (HTI) media (Schoenberg & Sayers 1995). Under the additional assumption of dry fractures, normal and tangential fracture weakness is estimated from slow and fast shear wave velocities of the sonic log. In the second step we apply Backus-style upscaling to construct effective anisotropy parameters on an appropriate length scale. In order to honor the HTI anisotropy present at each layer we have developed a new extension of the classical Backus averaging for layered isotropic media (Backus 1962) . Our new method assumes layered HTI media with constant anisotropy orientation as recovered in the first step. It leads to an effective horizontal orthorhombic elastic model. From this model Thomsen-style anisotropy parameters are calculated to derive azimuth-dependent normal move out (NMO) velocities (see Grechka & Tsvankin 1998). In our presentation we will show results of our approach from sonic well logs in the Surat Basin to investigate the potential of reconstructing S-wave velocity anisotropy and fracture density from azimuth dependent NMO velocities profiles.

A means to estimate thermal and kinetic parameters of coal dust layer from hot surface ignition tests.

PubMed

Park, Haejun; Rangwala, Ali S; Dembsey, Nicholas A

2009-08-30

A method to estimate thermal and kinetic parameters of Pittsburgh seam coal subject to thermal runaway is presented using the standard ASTM E 2021 hot surface ignition test apparatus. Parameters include thermal conductivity (k), activation energy (E), coupled term (QA) of heat of reaction (Q) and pre-exponential factor (A) which are required, but rarely known input values to determine the thermal runaway propensity of a dust material. Four different dust layer thicknesses: 6.4, 12.7, 19.1 and 25.4mm, are tested, and among them, a single steady state dust layer temperature profile of 12.7 mm thick dust layer is used to estimate k, E and QA. k is calculated by equating heat flux from the hot surface layer and heat loss rate on the boundary assuming negligible heat generation in the coal dust layer at a low hot surface temperature. E and QA are calculated by optimizing a numerically estimated steady state dust layer temperature distribution to the experimentally obtained temperature profile of a 12.7 mm thick dust layer. Two unknowns, E and QA, are reduced to one from the correlation of E and QA obtained at criticality of thermal runaway. The estimated k is 0.1 W/mK matching the previously reported value. E ranges from 61.7 to 83.1 kJ/mol, and the corresponding QA ranges from 1.7 x 10(9) to 4.8 x 10(11)J/kg s. The mean values of E (72.4 kJ/mol) and QA (2.8 x 10(10)J/kg s) are used to predict the critical hot surface temperatures for other thicknesses, and good agreement is observed between measured and experimental values. Also, the estimated E and QA ranges match the corresponding ranges calculated from the multiple tests method and values reported in previous research.

Performance of double-layer biofilter packed with coal fly ash ceramic granules in treating highly polluted river water.

PubMed

Jing, Zhaoqian; Li, Yu-You; Cao, Shiwei; Liu, Yuyu

2012-09-01

To improve trickling filters' denitrification efficiency, a biofilter with a trickling upper layer and a submerged lower layer was developed and applied in treating highly polluted river water. It was packed with porous coal fly ash ceramic granules. Its start-up characteristics, influence of hydraulic loading rates (HLR), carbon/nitrogen (C/N) ratio and filter depth on pollutants removal were investigated. The results indicated this biofilter was started quickly in 16 days with river sediment as inoculum. Alternating nitrification and denitrification were achieved when water flowed downwards. COD and nitrogen were mainly removed in the upper layer and the lower layer, respectively. With HLR of 4.0-5.0m(3)/(m(2)d), chemical oxygen demand (COD), ammonium (NH(4)(+)-N) and total nitrogen (TN) in the effluent were below 50, 5 and 15 mg/L, respectively. This biofilter removed more than 80% of COD, 85% of NH(4)(+)-N and 60% of TN with C/N ratios ranging from 6 to 10. Copyright © 2012 Elsevier Ltd. All rights reserved.

Depositional history of the Fire Clay coal bed (Late Duckmantian), Eastern Kentucky, USA

USGS Publications Warehouse

Greb, S.F.; Eble, C.F.; Hower, J.C.

1999-01-01

More than 3800 coal thickness measurements, proximate analyses from 97 localities, and stratigraphic and sedimentological analyses from more than 300 outcrops and cores were used in conjunction with previously reported palynological and petrographic studies to map individual benches of the coal and document bench-scale variability in the Fire Clay (Hazard No. 4) coal bed across a 1860 km2 area of the Eastern Kentucky Coal Field. The bench architecture of the Fire Clay coal bed consists of uncommon leader benches, a persistent but variable lower bench, a widespread, and generally thick upper bench, and local, variable rider benches. Rheotrophic conditions are inferred for the leader benches and lower bench based on sedimentological associations, mixed palynomorph assemblages, locally common cannel coal layers, and generally high ash yields. The lower bench consistently exhibits vertical variability in petrography and palynology that reflects changing trophic conditions as topographic depressions infilled. Infilling also led to unconfined flooding and ultimately the drowning of the lower bench mire. The drowned mire was covered by an air-fall volcanic-ash deposit, which produced the characteristic flint clay parting. The extent and uniform thickness of the parting suggests that the ash layer was deposited in water on a relatively flat surface without a thick canopy or extensive standing vegetation across most of the study area. Ash deposits led to regional ponding and establishment of a second planar mire. Because the topography had become a broadly uniform, nutrient-rich surface, upper-bench peats became widespread with large areas of the mire distant to clastic sources. Vertical sections of thick (> 70 cm), low-ash yield, upper coal bench show a common palynomorph change from arborescent lycopod dominance upward to fern and densospore-producing, small lycopod dominance, inferred as a shift from planar to ombrotrophic mire phases. Domed mires appear to have been surrounded by wide areas of planar mires, where the coal was thinner (< 70 cm), higher in ash yield, and dominated by arborescent lycopods. Rectangular thickness trends suggest that syndepositional faulting influenced peat accumulation, and possibly the position of the domed mire phase. Faulting also influenced post-depositional clastic environments of deposition, resulting in sandstone channels with angular changes in orientation. Channels and lateral facies were locally draped by high-ash-yield rider coal benches, which sometimes merged with the upper coal bench. These arborescent-lycopod dominant rider coal benches were profoundly controlled by palcotopography, much like the leader coal benches. Each of the benches of coal documented here represent distinctly different mires that came together to form the Fire Clay coal bed, rather than a single mire periodically split by clastic influx. This is significant as each bench of the coal has its own characteristics, which contribute to the total coal characteristics. The large data set allows interpretation of both vertical and lateral limits to postulated domed phases in the upper coal bench, and to the delineation of subtle tectonic structures that allow for meaningful thickness projections beyond the limits of present mining.A study was conducted to analyze the depositional history of the Fire Clay coal bed in the eastern Kentucky coal field. The study involved over 3800 coal thickness measurements, proximate analyses from 97 localities, and stratigraphic and sedimentological analyses from more than 300 outcrops and cores in conjunction with previously reported palynological and petrographic studies to map individual benches of the coal and document bench-scale variability.

Modeling of Three Flat Coal Seams Strata Developing at Open Pit Miming

NASA Astrophysics Data System (ADS)

Gvozdkova, Tatiana; Markov, Sergey; Demirel, Nuray; Anyona, Serony

2017-11-01

The use of low-cost direct dumpling technology, as is well known, has a relatively limited field of application: flat coal seams, and the higher the dip angle of the seam, the more difficult it is to place the necessary volume of overburden rock in the dumping layers. For this, we have to pour four-tier dumps. In this article, four possible options for piling the dump have been studied and prerequisites have been made for further research aimed at improving the efficiency of the use of direct dumpling technology in the development of flat coal seams.

Coal Rank and Stratigraphy of Pennsylvanian Coal and Coaly Shale Samples, Young County, North-Central Texas

USGS Publications Warehouse

Guevara, Edgar H.; Breton, Caroline; Hackley, Paul C.

2007-01-01

Vitrinite reflectance measurements were made to determine the rank of selected subsurface coal and coaly shale samples from Young County, north-central Texas, for the National Coal Resources Database System State Cooperative Program conducted by the Bureau of Economic Geology at The University of Texas at Austin. This research is the continuation of a pilot study that began in adjacent Archer County, and forms part of a larger investigation of the coalbed methane resource potential of Pennsylvanian coals in north-central Texas. A total of 57 samples of coal and coaly shale fragments were hand-picked from drill cuttings from depths of about 2,000 ft in five wells, and Ro determinations were made on an initial 10-sample subset. Electric-log correlation of the sampled wells indicates that the collected samples represent coal and coaly shale layers in the Strawn (Pennsylvanian), Canyon (Pennsylvanian), and Cisco (Pennsylvanian-Permian) Groups. Coal rank in the initial sample subset ranges from lignite (Ro=0.39), in a sample from the Cisco Group at a depth of 310 to 320 ft, to high volatile bituminous A coal (Ro=0.91) in a sample from the lower part of the Canyon Group at a depth of 2,030 to 2,040 ft.

[Macromolecular aromatic network characteristics of Chinese power coal analyzed by synchronous fluorescence and X-ray diffraction].

PubMed

Ye, Cui-Ping; Feng, Jie; Li, Wen-Ying

2012-07-01

Coal structure, especially the macromolecular aromatic skeleton structure, has a strong influence on coke reactivity and coal gasification, so it is the key to grasp the macromolecular aromatic skeleton coal structure for getting the reasonable high efficiency utilization of coal. However, it is difficult to acquire their information due to the complex compositions and structure of coal. It has been found that the macromolecular aromatic network coal structure would be most isolated if small molecular of coal was first extracted. Then the macromolecular aromatic skeleton coal structure would be clearly analyzed by instruments, such as X-ray diffraction (XRD), fluorescence spectroscopy with synchronous mode (Syn-F), Gel permeation chromatography (GPC) etc. Based on the previous results, according to the stepwise fractional liquid extraction, two Chinese typical power coals, PS and HDG, were extracted by silica gel as stationary phase and acetonitrile, tetrahydrofuran (THF), pyridine and 1-methyl-2-pyrollidinone (NMP) as a solvent group for sequential elution. GPC, Syn-F and XRD were applied to investigate molecular mass distribution, condensed aromatic structure and crystal characteristics. The results showed that the size of aromatic layers (La) is small (3-3.95 nm) and the stacking heights (Lc) are 0.8-1.2 nm. The molecular mass distribution of the macromolecular aromatic network structure is between 400 and 1 130 amu, with condensed aromatic numbers of 3-7 in the structure units.

Geomorphology of coal seam fires

NASA Astrophysics Data System (ADS)

Kuenzer, Claudia; Stracher, Glenn B.

2012-02-01

Coal fires occur in underground natural coal seams, in exposed surface seams, and in coal storage or waste piles. The fires ignite through spontaneous combustion or natural or anthropogenic causes. They are reported from China, India, USA, South Africa, Australia, and Russia, as well as many other countries. Coal fires lead to loss of a valuable resource (coal), the emission of greenhouse-relevant and toxic gases, and vegetation deterioration. A dangerous aspect of the fires is the threat to local mines, industries, and settlements through the volume loss underground. Surface collapse in coal fire areas is common. Thus, coal fires are significantly affecting the evolution of the landscape. Based on more than a decade of experience with in situ mapping of coal fire areas worldwide, a general classification system for coal fires is presented. Furthermore, coal seam fire geomorphology is explained in detail. The major landforms associated with, and induced by, these fires are presented. The landforms include manifestations resulting from bedrock surface fracturing, such as fissures, cracks, funnels, vents, and sponges. Further manifestations resulting from surface bedrock subsidence include sinkholes, trenches, depressions, partial surface subsidence, large surface subsidence, and slides. Additional geomorphologic coal fire manifestations include exposed ash layers, pyrometamorphic rocks, and fumarolic minerals. The origin, evolution, and possible future development of these features are explained, and examples from in situ surveys, as well as from high-resolution satellite data analyses, are presented. The geomorphology of coal fires has not been presented in a systematic manner. Knowledge of coal fire geomorphology enables the detection of underground coal fires based on distinct surface manifestations. Furthermore, it allows judgments about the safety of coal fire-affected terrain. Additionally, geomorphologic features are indicators of the burning stage of fires. Finally, coal fire geomorphology helps to explain landscape features whose occurrence would otherwise not be understood. Although coal fire-induced thermal anomalies and gas release are also indications of coal fire activity, as addressed by many investigators, no assessment is complete without sound geomorphologic mapping of the fire-induced geomorphologic features.

Subverting Toll-Like Receptor Signaling by Bacterial Pathogens

PubMed Central

McGuire, Victoria A.; Arthur, J. Simon C.

2015-01-01

Pathogenic bacteria are detected by pattern-recognition receptors (PRRs) expressed on innate immune cells, which activate intracellular signal transduction pathways to elicit an immune response. Toll-like receptors are, perhaps, the most studied of the PRRs and can activate the mitogen-activated protein kinase (MAPK) and Nuclear Factor-κB (NF-κB) pathways. These pathways are critical for mounting an effective immune response. In order to evade detection and promote virulence, many pathogens subvert the host immune response by targeting components of these signal transduction pathways. This mini-review highlights the diverse mechanisms that bacterial pathogens have evolved to manipulate the innate immune response, with a particular focus on those that target MAPK and NF-κB signaling pathways. Understanding the elaborate strategies that pathogens employ to subvert the immune response not only highlights the importance of these proteins in mounting effective immune responses, but may also identify novel approaches for treatment or prevention of infection. PMID:26648936

Paleoecological interpretation of a middle Pennsylvanian coal bed in the central Appalachian basin, U.S.A.

USGS Publications Warehouse

Eble, C.F.; Grady, W.C.

1990-01-01

At least 180 small spore species assignable to 62 miospore genera have been identified from the Middle Pennsylvanian Hernshaw coal bed in southern West Virginia, and its stratigraphic equivalent, the Fire Clay coal bed, in eastern Kentucky. The established natural affinities of a majority of these miospore taxa indicate that the Hernshaw-Fire Clay peat swamp supported a diverse flora consisting of arborescent and "herbaceous" lycopods, ferns (tree-like and small varities), calamities and cordaites. Four floral groupings are recognized in the Hernshaw-Fire Clay coal bed. The inferred paleoecology and vertical stratification of each of these four floral groupings is similar in structure to the "phasic" floral communities found in modern domed peat systems, suggesting that the ancient Hernshaw-Fire Clay peat swamp was a domed deposit. Compositional characteristics (petrographic make up, ash yield and sulfur content) associated with the four groupings are consistent with, and support this interpretation. Where uninterrupted by inorganic partings, the Hernshaw-Fire Clay coal bed commonly contains basal coal layers dominated by Lycospora-bearing arborescent lycopods, with successive increments showing a progression to a more fern- and "herbaceous"-lycopod-dominant flora in younger layers. These observations are corroborated by petrographic analyses, which show the bed to be compositionally stratified. Increments dominated by Lycospora have high vitrinite contents, in contrast to increments containing increased percentages of fern- and "herbaceous"-lycopod-affiliated taxa that are enriched in inertinite macerals. The volcanic ash fall, preserved as the flint-clay parting in the Hernshaw-Fire Clay coal bed, had a considerable effect on the development of the ancient Hernshaw-Fire Clay peat swamp. Besides interrupting peat formation, the presence of an inorganic substrate represent a major change in edaphic conditions within the swamp. This disruption is demonstrated by a change in palynflora and by the establishment and proliferation of some plant groups, notably cordaites and calamites, that may have been better adapted to growth on mineral soils. These palynologic and petrographic relationships, thought to be indicative of a domed peat-swamp origin, are not confined to the Hernshaw-Fire Clay coal bed, but appear to be characteristic of many coal beds in the Appalachian basin, and also of coal beds in other basins. ?? 1990.

Temperature dependence of the vapour tension of methyl-substituted phenol derivatives

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.G. Gagarin

2007-05-15

Notable among the coking products of coal are phenol and its derivatives, derived for the coal tar and water layer above ht tar. Given that phenol an its derivatives are mainly extracted from coal tar fractions by rectification, information on how the vapor tension of the individual components depends on the temperature is of great importance. For phenol and various substituted alkylphenols there are tabular data. In the pre-computer era these data were sufficient for the separation of phenol mixtures. However, the development and introduction of information technology in the coal industry and in the design process demands the mathematicalmore » description of the physicochemical processes of coking products. The temperature dependence of the saturated vapor pressure for organic compounds is commonly described by the Antoine equation.« less

Numerical investigations on mapping permeability heterogeneity in coal seam gas reservoirs using seismo-electric methods

NASA Astrophysics Data System (ADS)

Gross, L.; Shaw, S.

2016-04-01

Mapping the horizontal distribution of permeability is a key problem for the coal seam gas industry. Poststack seismic data with anisotropy attributes provide estimates for fracture density and orientation which are then interpreted in terms of permeability. This approach delivers an indirect measure of permeability and can fail if other sources of anisotropy (for instance stress) come into play. Seismo-electric methods, based on recording the electric signal from pore fluid movements stimulated through a seismic wave, measure permeability directly. In this paper we use numerical simulations to demonstrate that the seismo-electric method is potentially suitable to map the horizontal distribution of permeability changes across coal seams. We propose the use of an amplitude to offset (AVO) analysis of the electrical signal in combination with poststack seismic data collected during the exploration phase. Recording of electrical signals from a simple seismic source can be closer to production planning and operations. The numerical model is based on a sonic wave propagation model under the low frequency, saturated media assumption and uses a coupled high order spectral element and low order finite element solver. We investigate the impact of seam thickness, coal seam layering, layering in the overburden and horizontal heterogeneity of permeability.

Coal Fields and Federal Lands of the Conterminous United States

USGS Publications Warehouse

Biewick, Laura

1997-01-01

The map depicts the relationship of coal and public lands in the conterminous U. S. Multiple GIS layers are being created for the purpose of deriving estimates of how much coal is owned and administered by the Federal government. Federal coal areas have a profound effect on land-management decisions. Regulatory agencies attempt to balance energy development with alternative land-use and environmental concerns. A GIS database of Federal lands used in energy resource assessments is being developed by the U. S. Geological Survey (USGS) in cooperation with the U.S. Bureau of Land Management (BLM) to integrate information on status of public land, and minerals owned by the Federal government with geologic information on coal resources, other spatial data, coal quality characteristics, and coal availability for development. Using national-scale data we estimate that approximately 60 percent of the area underlain by coal-bearing rocks in the conterminous United States are under Federal surface. Coal produced from Federal leases has tripled from about 12 percent of the total U.S. production in 1976 to almost 34 percent in 1995 (Energy Information Administration website ftp://ftp.eia.doe.gov/pub/coal/cia_95_tables/t13p01.txt). The reason for this increase is demand for low-sulfur coal for use in power plants and the fact that large reserves of this low-sulfur coal are in the western interior U.S., where the Federal government owns the rights to most of the coal reserves. The map was created using Arc/Info 7.0.3 on a UNIX system. The HPGL2 plot file for this map is available from the USGS Energy Resource Surveys Team from http://energy.cr.usgs.gov:8080/energy/coal.html.

3D Geological Modeling of CoalBed Methane (CBM) Resources in the Taldykuduk Block Karaganda Coal Basin, Kazakhstan

NASA Astrophysics Data System (ADS)

Sadykov, Raman; Kiponievich Ogay, Evgeniy; Royer, Jean-Jacques; Zhapbasbayev, Uzak; Panfilova, Irina

2015-04-01

Coal Bed Methane (CBM) is gas stored in coal layers. It can be extracted from wells after hydraulic fracturing and/or solvent injection, and secondary recovery techniques such as CO2 injection. Karaganda Basin is a very favorable candidate region to develop CBM production for the following reasons: (i) Huge gas potential; (ii) Available technologies for extracting and commercializing the gas produced by CBM methods; (iii) Experience in degassing during underground mining operations for safety reasons; (iv) Local needs in energy for producing electricity for the industrial and domestic market. The objectives of this work are to model the Taldykuduk block coal layers and their properties focusing on Coal Bed Methane production. It is motivated by the availability of large coal bed methane resources in Karaganda coal basin which includes 4 300 Bm3 equivalent 2 billion tons of coal (B = billion = 109) with gas content 15-25 m3/t of coal (for comparison San Juan basin (USA) has < 20 m3/t). The CBM reserves estimations are about: Saransk block, 26.3 Bm3 and Taldykuduk block, 23.5 Bm3. Methane (CH4) can be considered as an environmentally-friendly fuel compared to coal. Actually, the methane extracted during mining is released in the atmosphere, collecting it for recovering energy will reduce CO2 equivalent emissions by 36 Mt, good news regarding climate warming issues. The exploitation method will be based on a EOR technology consisting in injecting CO2 which replaces methane in pores because it has a higher adsorption capacity than CH4; exploiting CBM by CO2 injection provides thus a safe way to sequestrate CO2 in adsorbed form. The 3D geological model was built on Gocad/Skua using the following available data set: 926 wells and large area (7 x 12 km). No seismic data; coal type and chemical components (S, ash, …); unreliable available cross-section & maps due to old acquisition; quality mature coal; complex heterogeneous fractures network reported on geological cross sections; and utilization issues of the water extracted in the early stages of exploitation. The resulting 3D faulted model which includes more than 100 of faults will be further used to simulate the secondary recovery of methane by injecting CO2. The simulation will be carried out on a flow simulator assuming a two phase dimensionless formulation of CBM production in a double porosity model considering two domains: the matrix (m) and the fracture (f) for which the initial and boundary conditions are different. The resulting comprehensive 3D models had helped in better understanding the tectonic structures of the region, especially the relationships between the fault systems.

Laboratory studies to characterize the efficacy of sand capping a coal tar-contaminated sediment.

PubMed

Hyun, Seunghun; Jafvert, Chad T; Lee, Linda S; Rao, P Suresh C

2006-06-01

Placement of a microbial active sand cap on a coal tar-contaminated river sediment has been suggested as a cost effective remediation strategy. This approach assumes that the flux of contaminants from the sediment is sufficiently balanced by oxygen and nutrient fluxes into the sand layer such that microbial activity will reduce contaminant concentrations within the new benthic zone and reduce the contaminant flux to the water column. The dynamics of such a system were evaluated using batch and column studies with microbial communities from tar-contaminated sediment under different aeration and nutrient inputs. In a 30-d batch degradation study on aqueous extracts of coal tar sediment, oxygen and nutrient concentrations were found to be key parameters controlling the degradation rates of polycyclic aromatic hydrocarbons (PAHs). For the five PAHs monitored (naphthalene, fluorene, phenanthrene, anthracene, and pyrene), degradation rates were inversely proportional to molecular size. For the column studies, where three columns were packed with a 20-cm sand layer on the top of a 5 cm of sediment layer, flow was established to sand layers with (1) aerated water, (2) N(2) sparged water, or (3) HgCl(2)-sterilized N(2) sparged water. After steady-state conditions, PAH concentrations in effluents were the lowest in the aerated column, except for pyrene, whose concentration was invariant with all effluents. These laboratory scale studies support that if sufficient aeration can be achieved in the field through either active and passive means, the resulting microbially active sand layer can improve the water quality of the benthic zone and reduce the flux of many, but not all, PAHs to the water column.

Coal Layer Identification using Electrical Resistivity Imaging Method in Sinjai Area South Sulawesi

NASA Astrophysics Data System (ADS)

Ilham Samanlangi, Andi

2018-03-01

The purpose of this research is to image subsurface resistivity for coal identification in Panaikang Village, Sinjai, South Sulawesi.Resistivity measurements were conducted in 3 lines of length 400 meters and 300 meter using resistivity imaging, dipole-dipole configuration. Resistivity data was processed using Res2DInv software to image resistivity variation and interpret lithology. The research results shown that coal resistivity in Line is about 70-200 Ωm, Line 2 is about 70-90 Ωm, and Line 3 is about 70-200 Ωm with average thickness about 10 meters and distributed to the east of research area.

Research on preventive technologies for bed-separation water hazard in China coal mines

NASA Astrophysics Data System (ADS)

Gui, Herong; Tong, Shijie; Qiu, Weizhong; Lin, Manli

2018-03-01

Bed-separation water is one of the major water hazards in coal mines. Targeted researches on the preventive technologies are of paramount importance to safe mining. This article studied the restrictive effect of geological and mining factors, such as lithological properties of roof strata, coal seam inclination, water source to bed separations, roof management method, dimensions of mining working face, and mining progress, on the formation of bed-separation water hazard. The key techniques to prevent bed-separation water-related accidents include interception, diversion, destructing the buffer layer, grouting and backfilling, etc. The operation and efficiency of each technique are corroborated in field engineering cases. The results of this study will offer reference to countries with similar mining conditions in the researches on bed-separation water burst and hazard control in coal mines.

Efficient and large scale synthesis of graphene from coal and its film electrical properties studies.

PubMed

Wu, Yingpeng; Ma, Yanfeng; Wang, Yan; Huang, Lu; Li, Na; Zhang, Tengfei; Zhang, Yi; Wan, Xiangjian; Huang, Yi; Chen, Yongsheng

2013-02-01

Coal, which is abundant and has an incompact structure, is a good candidate to replace graphite as the raw material for the production of graphene. Here, a new solution phase technique for the preparation of graphene from coal has been developed. The precursor: graphene oxide got from coal was examined by atomic force microscopy, dynamic light scattering and X-ray diffraction, the results showed the GO was a small and single layer sheet. The graphene was examined by X-ray photoelectron spectroscopy, and Raman spectroscopy. Furthermore, graphene films have been prepared using direct solution process and the electrical conductivity and Hall effect have been studied. The results showed the conductivity of the films could reach as high as 2.5 x 10(5) Sm(-1) and exhibited an n-type behavior.

Necroptotic debris including damaged mitochondria elicits sepsis-like syndrome during late-phase tularemia.

PubMed

Singh, Anju; Periasamy, Sivakumar; Malik, Meenakshi; Bakshi, Chandra Shekhar; Stephen, Laurie; Ault, Jeffrey G; Mannella, Carmen A; Sellati, Timothy J

2017-01-01

Infection with Francisella tularensis ssp. tularensis ( Ft ) strain SchuS4 causes an often lethal disease known as tularemia in rodents, non-human primates, and humans. Ft subverts host cell death programs to facilitate their exponential replication within macrophages and other cell types during early respiratory infection (⩽72 h). The mechanism(s) by which cell death is triggered remains incompletely defined, as does the impact of Ft on mitochondria, the host cell's organellar 'canary in a coal mine'. Herein, we reveal that Ft infection of host cells, particularly macrophages and polymorphonuclear leukocytes, drives necroptosis via a receptor-interacting protein kinase 1/3-mediated mechanism. During necroptosis mitochondria and other organelles become damaged. Ft -induced mitochondrial damage is characterized by: (i) a decrease in membrane potential and consequent mitochondrial oncosis or swelling, (ii) increased generation of superoxide radicals, and (iii) release of intact or damaged mitochondria into the lung parenchyma. Host cell recognition of and response to released mitochondria and other damage-associated molecular patterns engenders a sepsis-like syndrome typified by production of TNF, IL-1 β , IL-6, IL-12p70, and IFN- γ during late-phase tularemia (⩾72 h), but are absent early during infection.

Land status and federal mineral ownership in the Powder River basin, Wyoming and Montana; a digital data set for geographic information systems

USGS Publications Warehouse

Biewick, Laura; Urbanowski, Shayne R.; Cain, Sheila; Neasloney, Larry

1998-01-01

As the Nation's energy resources continue to be examined for development, it is critical that a digital database exist that contains location data for all Federal land and mineral resources. The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), is collecting these ownership files and compiling them in Environmental Systems Research Institute, Inc. (ESRI) ARC/INFO coverages, to form a standardized data library. A coverage is a digital version of a map in the form of vector data storage. These coverages are combined with models of coal deposits from the USGS National Coal Resource Assessment project, a five-year effort to identify and characterize the coal beds and coal zones that will provide fuel for the Nation’s energy needs during the first quarter of the twenty-first century. Geographic and geologic data layers are integrated in a Geographic Information System (GIS) to answer complex geo-spatial questions concerning coal resource occurrence.

Post-translational regulation of plant immunity.

PubMed

Withers, John; Dong, Xinnian

2017-08-01

Plants have evolved multi-layered molecular defense strategies to protect against pathogens. Plant immune signaling largely relies on post-translational modifications (PTMs) to induce rapid alterations of signaling pathways to achieve a response that is appropriate to the type of pathogen and infection pressure. In host cells, dynamic PTMs have emerged as powerful regulatory mechanisms that cells use to adjust their immune response. PTM is also a virulence strategy used by pathogens to subvert host immunity through the activities of effector proteins secreted into the host cell. Recent studies focusing on deciphering post-translational mechanisms underlying plant immunity have offered an in-depth view of how PTMs facilitate efficient immune responses and have provided a more dynamic and holistic view of plant immunity. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Calcite-impregnated defluidization structures in littoral sands of Mono Lake, California

USGS Publications Warehouse

Cloud, P.; Lajoie, K.R.

1980-01-01

Associated locally with well-known tufa mounds and towers of Mono Lake, California, are subvertical, concretionary sand structures through which fresh calcium-containing artesian waters moved up to sites of calcium carbonate precipitation beneath and adjacent to the lake. The structures include closely spaced calcite-impregnated columns, tubes, and other configurations with subcylindrical to bizarre cross sections and predominantly vertical orientation in coarse, barely coherent pumice sands along the south shore of the lake. Many structures terminate upward in extensive calcareous layers of caliche and tufa. Locally they enter the bases of tufa mounds and towers. A common form superficially resembles root casts and animal burrows except that branching is mostly up instead of down. Similar defluidization structures in ancient sedimentary rocks have been mistakenly interpreted as fossil burrows.

Fort Campbell Childers House: Historic Maintenance and Repair Manual

DTIC Science & Technology

2006-09-01

coal-tar pitch and surfaced with a layer of gravel or slag in a heavy coat of asphalt or coal-tar pitch or finished with a cap sheet; generally used...such as lead, tin, copper, terneplate, and zinc with appropriate chemical methods because their finishes can be easily abraded by blasting methods...tin, copper, terneplate, and zinc with grit blasting which will abrade the surface of the metal. • Using cleaning methods, which alter or damage

Fluidized bed coal combustion reactor

NASA Technical Reports Server (NTRS)

Moynihan, P. I.; Young, D. L. (Inventor)

1981-01-01

A fluidized bed coal reactor includes a combination nozzle-injector ash-removal unit formed by a grid of closely spaced open channels, each containing a worm screw conveyor, which function as continuous ash removal troughs. A pressurized air-coal mixture is introduced below the unit and is injected through the elongated nozzles formed by the spaces between the channels. The ash build-up in the troughs protects the worm screw conveyors as does the cooling action of the injected mixture. The ash layer and the pressure from the injectors support a fluidized flame combustion zone above the grid which heats water in boiler tubes disposed within and/or above the combustion zone and/or within the walls of the reactor.

Potential effects of surface coal mining on the hydrology of the Little Bear Creek area, Moorhead coal field, southeastern Montana

USGS Publications Warehouse

McClymonds, N.E.

1986-01-01

The Little Bear Creek area of the Moorhead Coal Field, 27 miles south of Ashland, Montana, contains large reserves of Federally owned coal that have been identified for potential lease sale. A hydrologic study was conducted in the area to describe existing hydrologic system and to assess potential effects of surface mining on local water resources. Hydrologic data collected from private wells, observation wells, test holes and springs indicate that the aquifers are coal and sandstone beds in the upper part of the Tongue River Member, Fort Union Formation (Paleocene age), and sand and gravel layers of valley alluvium (Pleistocene and Holocene age). Surface water is available from ephemeral flow along stretches of the main streams, and from stock ponds throughout the area. Mining the Anderson and Dietz coal beds would destroy one stock well and several stock ponds, would possibly interfere with the flow of one spring, and would lower the potentiometric surface within the coal and sandstone aquifers. The alluvial aquifer beneath Little Bear Creek and Davidson Draw would be removed at the mine site, as would sandstone and coal aquifers above the mine floor. Although mining would alter existing hydrologic systems, alternative water supplies are available. Planned structuring of the spoils and reconstruction of the alluvial aquifers could minimize downstream water-quality degradation. (USGS)

Preparation of Functionally Graded Materials (FGMs) Using Coal Fly Ash and NiCr-Based Alloy Powder by Spark Plasma Sintering (SPS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaneko, Gen-yo; Kitagawa, Hiroyuki; Hasezaki, Kazuhiro

2008-02-15

Functionally Graded Materials (FGMs) were prepared by spark plasma sintering (SPS) using coal fly ash and NiCr alloy powder. The coal fly ash was produced by the Misumi Coal Thermal Power Station (Chugoku Electric Power Co., Inc.), with 80 wt% nickel and 20 wt% chromium (Fukuda Metal Foil and Powder Co., Ltd.) used as source materials. The sintering temperature in the graphite die was 1000 deg. C. X-ray diffraction patterns of the sintered coal fly ash materials indicated that mullite (3Al{sub 2}O{sub 3}{center_dot}2SiO{sub 2}) and silica (SiO{sub 2}) phases were predominant. Direct joining of coal fly ash and NiCr causesmore » fracture at the interface. This is due to the mismatch in the thermal expansion coefficients (CTE). A crack in the FGM was observed between the two layers with a CTE difference of over 4.86x10{sup -6} K{sup -1}, while a crack in the FGM was difficult to detect when the CTE difference was less than 2.77x10{sup -6} K{sup -1}.« less

Palaeoenvironmental reconstruction of Hüsamlar coal seam, SW Turkey

NASA Astrophysics Data System (ADS)

Büçkün, Zeynep; İnaner, Hülya; Oskay, Riza Görkem; Christanis, Kimon

2015-06-01

The Ören and Yatağan Basins in SW Turkey host several Miocene coal deposits currently under exploitation for power generation. The present study aims to provide insight into the palaeoenvironmental conditions, which controlled the formation of the Hüsamlar coal seam located in Ören Basin. The coal seam displays many sharp alternations of matrix lignite beds and inorganic, lacustrine sediment layers. The coal is a medium-to-high ash lignite (10.47-31.16 wt%, on dry basis) with high total sulphur content (up to 10 wt%, on dry, ash-free basis), which makes it prone to self-combustion. The maceral composition indicates that the peat-forming vegetation consisted of both arboreal and herbaceous plants, with the latter being predominant in the upper part of the seam. Mica and feldspars contribute to the low part of the seam; carbonates are dominant in the upper part, whereas quartz and pyrite are present along the entire coal profile. The sudden transitions of the telmatic to the lacustrine regime and reverse is attributed to tectonic movements that controlled water table levels in the palaeomire, which affected surface runoff and hence, clastic deposition.

Coal mining activities change plant community structure due to air pollution and soil degradation.

PubMed

Pandey, Bhanu; Agrawal, Madhoolika; Singh, Siddharth

2014-10-01

The aim of this study was to investigate the effects of coal mining activities on the community structures of woody and herbaceous plants. The response of individual plants of community to defilement caused by coal mining was also assessed. Air monitoring, soil physico-chemical and phytosociological analyses were carried around Jharia coalfield (JCF) and Raniganj coalfield. The importance value index of sensitive species minified and those of tolerant species enhanced with increasing pollution load and altered soil quality around coal mining areas. Although the species richness of woody and herbaceous plants decreased with higher pollution load, a large number of species acclimatized to the stress caused by the coal mining activities. Woody plant community at JCF was more affected by coal mining than herbaceous community. Canonical correspondence analysis revealed that structure of herbaceous community was mainly driven by soil total organic carbon, soil nitrogen, whereas woody layer community was influenced by sulphur dioxide in ambient air, soil sulphate and soil phosphorus. The changes in species diversity observed at mining areas indicated an increase in the proportion of resistant herbs and grasses showing a tendency towards a definite selection strategy of ecosystem in response to air pollution and altered soil characteristics.

Effect of Amount of Carbon on the Reduction Efficiency of Iron Ore-Coal Composite Pellets in Multi-layer Bed Rotary Hearth Furnace (RHF)

NASA Astrophysics Data System (ADS)

Mishra, Srinibash; Roy, Gour Gopal

2016-08-01

The effect of carbon-to-hematite molar ratio has been studied on the reduction efficiency of iron ore-coal composite pellet reduced at 1523 K (1250 °C) for 20 minutes in a laboratory scale multi-layer bed rotary hearth furnace (RHF). Reduced pellets have been characterized through weight loss measurement, estimation of porosity, shrinkage, qualitative and quantitative phase analysis by XRD. Performance parameters such as the degree of reduction, metallization, carbon efficiency, productivity, and compressive strength have been calculated to compare the process efficacy at different carbon levels in the pellets. Pellets with optimum carbon-to-hematite ratio (C/Fe2O3 molar ratio = 1.66) that is much below the stoichiometric carbon required for direct reduction of hematite yielded maximum reduction, better carbon utilization, and productivity for all three layers. Top layer exhibited maximum reduction at comparatively lower carbon level (C/Fe2O3 molar ratio <2.33) in the pellet, while bottom layer exceeded top layer reduction at higher carbon level (C/Fe2O3 molar ratio >2.33). Correlation between degree of reduction and metallization indicated non-isothermal kinetics influenced by heat and mass transfer in multi-layer bed RHF. Compressive strength of the partially reduced pellet with optimum carbon content (C/Fe2O3 molar ratio = 1.66) showed that they could be potentially used as an alternate feed in a blast furnace or any other smelting reactor.

GIS Representation of Coal-Bearing Areas in North, Central, and South America

USGS Publications Warehouse

Tewalt, Susan J.; Kinney, Scott A.; Merrill, Matthew D.

2008-01-01

Worldwide coal consumption and international coal trade are projected to increase in the next several decades (Energy Information Administration, 2007). A search of existing literature indicates that in the Western Hemisphere, coal resources are known to occur in about 30 countries. The need exists to be able to depict these areas in a digital format for use in Geographic Information System (GIS) applications at small scales (large areas) and in visual presentations. Existing surficial geology GIS layers of the appropriate geologic age have been used as an approximation to depict the extent of coal-bearing areas in North, Central, and South America, as well as Greenland (fig. 1). Global surficial geology GIS data were created by the U.S. Geological Survey (USGS) for use in world petroleum assessments (Hearn and others, 2003). These USGS publications served as the major sources for the selection and creation of polygons to represent coal-bearing areas. Additional publications and maps by various countries and agencies were also used as sources of coal locations. GIS geologic polygons were truncated where literature or hardcopy maps did not indicate the presence of coal. The depicted areas are not adequate for use in coal resource calculations, as they were not adjusted for geologic structure and do not include coal at depth. Additionally, some coal areas in Central America could not be represented by the mapped surficial geology and are shown only as points based on descriptions or depictions from scientific publications or available maps. The provided GIS files are intended to serve as a backdrop for display of coal information. Three attributes of the coal that are represented by the polygons or points include geologic age (or range of ages), published rank (or range of ranks), and information source (published sources for age, rank, or physical location, or GIS geology base).

Increasing the Reliability of the Work of Artificial Filtering Arrays for the Purification of Quarry Waste Water

NASA Astrophysics Data System (ADS)

Tyulenev, Maxim; Lesin, Yury; Litvin, Oleg; Maliukhina, Elena; Abay, Asmelash

2017-11-01

Features of geological structure of the Kuznetsk coal basin stipulate the application of a low-cost open technique of coal mining, which is more advantageous both from the economic standpoint, and by safety criteria of mining. However, open mining affects significantly the water resources of region. Intensive pollution of reservoirs and water courses, exhaustion of the underground water-bearing layers, violation of a hydrographic network, etc. be-long to the main disadvantages of an open technique of coal mining. Besides, the volume of the water coming into the mining producers exceeds signi-ficantly the needed quantity. According to the data of annual reports of ecology and natural resources department, 348.277 million m3 of water were ta-ken away during production of soft coal, brown coal and lignum fossil from waters of Kemerovo region in 2013 (mostly from underground water objects (96,5%) when draining of mine openings). At the same time, only 87.018 million m3 of water (25%) has been used within a year.

A Power-Efficient Clustering Protocol for Coal Mine Face Monitoring with Wireless Sensor Networks Under Channel Fading Conditions

PubMed Central

Ren, Peng; Qian, Jiansheng

2016-01-01

This study proposes a novel power-efficient and anti-fading clustering based on a cross-layer that is specific to the time-varying fading characteristics of channels in the monitoring of coal mine faces with wireless sensor networks. The number of active sensor nodes and a sliding window are set up such that the optimal number of cluster heads (CHs) is selected in each round. Based on a stable expected number of CHs, we explore the channel efficiency between nodes and the base station by using a probe frame and the joint surplus energy in assessing the CH selection. Moreover, the sending power of a node in different periods is regulated by the signal fade margin method. The simulation results demonstrate that compared with several common algorithms, the power-efficient and fading-aware clustering with a cross-layer (PEAFC-CL) protocol features a stable network topology and adaptability under signal time-varying fading, which effectively prolongs the lifetime of the network and reduces network packet loss, thus making it more applicable to the complex and variable environment characteristic of a coal mine face. PMID:27338380

Lidar Investigation of Aerosol Pollution Distribution near a Coal Power Plant

NASA Technical Reports Server (NTRS)

Mitsev, TS.; Kolarov, G.

1992-01-01

Using aerosol lidars with high spatial and temporal resolution with the possibility of real-time data interpretation can solve a large number of ecological problems related to the aerosol-field distribution and variation and the structure of convective flows. Significantly less expensive specialized lidars are used in studying anthropogenic aerosols in the planetary boundary layer. Here, we present results of lidar measurements of the mass-concentration field around a coal-fired power plant with intensive local aerosol sources. We studied the pollution evolution as a function of the emission dynamics and the presence of retaining layers. The technique used incorporates complex analysis of three types of lidar mapping: horizontal map of the aerosol field, vertical cross-section map, and a series of profiles along a selected path. The lidar-sounding cycle was performed for the time of atmosphere's quasi-stationarity.

Analysis of coal seam thickness and seismic wave amplitude: A wedge model

NASA Astrophysics Data System (ADS)

Zou, Guangui; Xu, Zhiliang; Peng, Suping; Fan, Feng

2018-01-01

Coal seam thickness is of great significance in mining coal resources. The focus of this study is to determine the relationship between coal seam thickness and seismic wave amplitude, and the factors influencing this relationship. We used a wedge model to analyze this relationship and its influencing factors. The results show that wave interference from the top and bottom interfaces is the primary reason for the linear relationship between seismic wave amplitude and wedge thickness, when the thickness of the wedge is less than one quarter of the wavelength. This relationship is influenced by the dominant frequency, reflection coefficients from the top and bottom boundaries, depth, thickness, and angle of the wedge. However, when the lateral shift between the reflected waves is smaller than the radius of the first Fresnel zone, the wedge angle and change in lithology at the top and bottom layers are considered to have little effect on the amplitude of the interference wave. The difference in the dominant frequency of seismic waves can be reduced by filtering, and the linear relationship between amplitude and coal thickness can be improved. Field data from Sihe coal mine was analyzed, and the error was found to be within 4% of the predicted seismic wave amplitude. The above conclusions could help predict the thickness of coal seam by seismic amplitude.

In situ Van der Pauw measurements of the Ni/YSZ anode during exposure to syngas with phosphine contaminant

NASA Astrophysics Data System (ADS)

Demircan, Oktay; Xu, Chunchuan; Zondlo, John; Finklea, Harry O.

Solid oxide fuel cells (SOFCs) represent an option to provide a bridging technology for energy conversion (coal syngas) as well as a long-term technology (hydrogen from biomass). Whether the fuel is coal syngas or hydrogen from biomass, the effect of impurities on the performance of the anode is a vital question. The anode resistivity during SOFC operation with phosphine-contaminated syngas was studied using the in situ Van der Pauw method. Commercial anode-supported solid oxide fuel cells (Ni/YSZ composite anodes, YSZ electrolytes) were exposed to a synthetic coal syngas mixture (H 2, H 2O, CO, and CO 2) at a constant current and their performance evaluated periodically with electrochemical methods (cyclic voltammetry, impedance spectroscopy, and polarization curves). In one test, after 170 h of phosphine exposure, a significant degradation of cell performance (loss of cell voltage, increase of series resistance and increase of polarization resistance) was evident. The rate of voltage loss was 1.4 mV h -1. The resistivity measurements on Ni/YSZ anode by the in situ Van der Pauw method showed that there were no significant changes in anode resistivity both under clean syngas and syngas with 10 ppm PH 3. XRD analysis suggested that Ni 5P 2 and P 2O 5 are two compounds accumulated on the anode. XPS studies provided support for the presence of two phosphorus phases with different oxidation states on the external anode surface. Phosphorus, in a positive oxidation state, was observed in the anode active layer. Based on these observations, the effect of 10 ppm phosphine impurity (or its reaction products with coal syngas) is assigned to the loss of performance of the Ni/YSZ active layer next to the electrolyte, and not to any changes in the thick Ni/YSZ support layer.

Petrology and palynology of the No. 5 block coal bed, northeastern Kentucky

USGS Publications Warehouse

Hower, J.C.; Eble, C.F.; Rathbone, R.F.

1994-01-01

The upper Middle Pennsylvanian (middle Westphalian D equivalent) No. 5 Block coal bed (Eastern Kentucky Coal Field of the Central Appalachian Basin) is a low-sulfur, compliance coal resource, dominantly comprised of dull, inertinite-rich lithotypes. Ash yields tend to be highly variable in the No. 5 Block, as does bed thickness and frequency of bed splitting. This study describes the petrographic, palynologic and geochemical characteristics of the No. 5 Block coal bed, and reports on some temporal and spatial trends among these parameters in eastern-northeastern Kentucky. Petrographically the No. 5 Block coal is predominated by dull, often high-ash lithotypes, with inertinite contents commonly exceeding 30% (mmf). The coal thins to the north-northwest where it tends to be higher in vitrinite and sulfur content. Representatives of large and small lycopsids and ferns (both tree-like and small varieties) dominate the No. 5 Block coal bed palynoflora. Calamite spores and cordaite pollen also occur but are less abundant. Small lycopsid (Densosporites spp. and related crassicingulate genera) and tree fern (e.g. Punctatisporites minutus, Laevigatosporites globosus) spore taxa are most abundant in dull lithotypes. Bright lithotypes contain higher percentages of arboreous lycopsid spores (Lycospora spp.). Regionally, the No. 5 Block coal contains abundant Torispora securis, a tree fern spore specially adapted for desiccation prevention. This, along with overall high percentages of inertinite macerals, suggest that peat accumulation may have taken place in a seasonally dry (?) paleoclimate. The No. 5 Block coal bed thickens rather dramatically in a NW-SE direction, as does the frequency of coal bed splitting. This phenomenon appears to be related to increased accomodation space in the southeastern portion of the study area, perhaps via penecontemporaneous growth faulting. Maceral and palynomorph variations within the bed correspond with these changes. Thin coal along the northwestern margin tends to be vetrinite rich and contains abundant Lycospora, perhaps reflecting relatively stable peat-forming conditions. Thicker coal to the southeast contains more inertinite, high-ash coal layers, and inorganic partings. Spore floras contain more small lycopsid and tree fern components and are temporally variable, perhaps indicating a more unstable peat-forming environment. ?? 1994.

Preparation and combustion of coal-water fuel from the Sin Pun coal deposit, southern Thailand

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

In response to an inquiry by the Department of Mineral Resources in Thailand, the Energy & Environmental Research Center (EERC) prepared a program to assess the responsiveness of Sin Pun lignite to the temperature and pressure conditions of hot-water drying. The results indicate that drying made several improvements in the coal, notably increases in heating value and carbon content and reductions in equilibrium moisture and oxygen content. The equilibrium moisture content decreased from 27 wt% for the raw coal to about 15 wt% for the hot-water-dried (HWD) coals. The energy density for a pumpable coal-water fuel (CWF) indicates an increasemore » from 4500 to 6100 Btu/lb by hot-water drying. Approximately 650 lb of HWD Sin Pun CWF were fired in the EERC`s combustion test facility. The fuel burned extremely well, with no feed problems noted during the course of the test. Fouling and slagging deposits each indicated a very low rate of ash deposition, with only a dusty layer formed on the cooled metal surfaces. The combustor was operated at between 20% and 25% excess air, resulting in a flue gas SO{sub 2} concentration averaging approximately 6500 parts per million.« less

Electric Pulse Discharge Activated Carbon Supercapacitors for Transportation Application

NASA Astrophysics Data System (ADS)

Nayak, Subhadarshi; Agrawal, Jyoti

2012-03-01

ScienceTomorrow is developing a high-speed, low-cost process for synthesizing high-porosity electrodes for electrochemical double-layer capacitors. Four types of coal (lignite, subbituminous, bituminous, and anthracite) were used as precursor materials for spark discharge activation with multiscale porous structure. The final porosity and pore distribution depended, among other factors, on precursor type. The high gas content in low-grade carbon resulted in mechanical disintegration, whereas high capacitance was attained in higher-grade coal. The properties, including capacitance, mechanical robustness, and internal conductivity, were excellent when the cost is taken into consideration.

A Comparison between Model Base Hardconstrain, Bandlimited, and Sparse-Spike Seismic Inversion: New Insights for CBM Reservoir Modelling on Muara Enim Formation, South Sumatra

NASA Astrophysics Data System (ADS)

Mohamad Noor, Faris; Adipta, Agra

2018-03-01

Coal Bed Methane (CBM) as a newly developed resource in Indonesia is one of the alternatives to relieve Indonesia’s dependencies on conventional energies. Coal resource of Muara Enim Formation is known as one of the prolific reservoirs in South Sumatra Basin. Seismic inversion and well analysis are done to determine the coal seam characteristics of Muara Enim Formation. This research uses three inversion methods, which are: model base hard- constrain, bandlimited, and sparse-spike inversion. Each type of seismic inversion has its own advantages to display the coal seam and its characteristic. Interpretation result from the analysis data shows that the Muara Enim coal seam has 20 (API) gamma ray value, 1 (gr/cc) – 1.4 (gr/cc) from density log, and low AI cutoff value range between 5000-6400 (m/s)*(g/cc). The distribution of coal seam is laterally thinning northwest to southeast. Coal seam is seen biasedly on model base hard constraint inversion and discontinued on band-limited inversion which isn’t similar to the geological model. The appropriate AI inversion is sparse spike inversion which has 0.884757 value from cross plot inversion as the best correlation value among the chosen inversion methods. Sparse Spike inversion its self-has high amplitude as a proper tool to identify coal seam continuity which commonly appears as a thin layer. Cross-sectional sparse spike inversion shows that there are possible new boreholes in CDP 3662-3722, CDP 3586-3622, and CDP 4004-4148 which is seen in seismic data as a thick coal seam.

Regeneratively cooled coal combustor/gasifier with integral dry ash removal

DOEpatents

Beaufrere, A.H.

1982-04-30

A coal combustor/gasifier is disclosed which produces a low or medium combustion gas fired furnances or boilers. Two concentric shells define a combustion air flows to provide regenerative cooling of the inner shell for dry ash operation. A fuel flow and a combustion air flow having opposed swirls are mixed and burned in a mixing-combustion portion of the combustion volume and the ash laden combustion products flow with a residual swirl into an ash separation region. The ash is cooled below the fusion temperature and is moved to the wall by centrifugal force where it is entrained in the cool wall boundary layer. The boundary layer is stabilized against ash re-entrainment as it is moved to an ash removal annulus by a flow of air from the plenum through slots in the inner shell, and by suction on an ash removal skimmer slot.

The Potential of Low-Cost Rpas for Multi-View Reconstruction of Sub-Vertical Rock Faces

NASA Astrophysics Data System (ADS)

Thoeni, K.; Guccione, D. E.; Santise, M.; Giacomini, A.; Roncella, R.; Forlani, G.

2016-06-01

The current work investigates the potential of two low-cost off-the-shelf quadcopters for multi-view reconstruction of sub-vertical rock faces. The two platforms used are a DJI Phantom 1 equipped with a Gopro Hero 3+ Black and a DJI Phantom 3 Professional with integrated camera. The study area is a small sub-vertical rock face. Several flights were performed with both cameras set in time-lapse mode. Hence, images were taken automatically but the flights were performed manually as the investigated rock face is very irregular which required manual adjustment of the yaw and roll for optimal coverage. The digital images were processed with commercial SfM software packages. Several processing settings were investigated in order to find out the one providing the most accurate 3D reconstruction of the rock face. To this aim, all 3D models produced with both platforms are compared to a point cloud obtained with a terrestrial laser scanner. Firstly, the difference between the use of coded ground control targets and the use of natural features was studied. Coded targets generally provide the best accuracy, but they need to be placed on the surface, which is not always possible, as sub-vertical rock faces are not easily accessible. Nevertheless, natural features can provide a good alternative if wisely chosen as shown in this work. Secondly, the influence of using fixed interior orientation parameters or self-calibration was investigated. The results show that, in the case of the used sensors and camera networks, self-calibration provides better results. To support such empirical finding, a numerical investigation using a Monte Carlo simulation was performed.

Distributed deformation structures in shallow water carbonates subsiding through a simple stress field (Jandaira Formation, NE Brazil)

NASA Astrophysics Data System (ADS)

Bertotti, Giovanni; Bisdom, Kevin; Bezerra, Hilario; Reijmer, John; Cazarin, Carol

2016-04-01

Despite the scarcity of major deformation structures such as folds and faults, the flat-lying, post-rift shallow water carbonates of the Jandaira Formation (Potiguar Basin, NE Brazil) display well-organized fracture systems distributed of tens of km2. Structures observed in the outcropping carbonates are sub-vertical, generally N-S trending mode I and hybrid veins and barren fractures, sub-vertical roughly E-W trending stylolites and sub-horizontal stylolites. These features developed during subsidence in a simple and constant stress field characterized by, beside gravity, a significant horizontal stress probably of tectonic origin. The corresponding depth curves have different origin and slopes and, therefore, cross each other resulting in position of the principal stresses which change with depth. As a result, the type and amount of fractures affecting subsiding rocks change despite the fact that the far-field stresses remain constant. Following early diagenesis and porosity elimination in the first 100-200m depth, Jandaira carbonates experienced wholesale fracturing at depths of 400-800m resulting in a network of NNW-NE trending fractures partly organized in conjugate sets with a low interfault angle and a sub-vertical intersection, and sub-vertical stylolites roughly perpendicular to the fractures. Intense fluid circulation was activated as a consequence through the carbonates. With increasing subsidence, sub-horizontal stylolites formed providing calcite which precipitated in the open fractures transforming them in veins. The Jandaira formation lost thereby the permeability it had reached during the previous stage. Because of the lack of major deformation, the outcrops of the Jandaira Formation is an excellent analog for carbonate reservoirs in the Middle East, South Atlantic and elsewhere.

Seismic, magnetic, and geotechnical properties of a landslide and clinker deposits, Powder River basin, Wyoming and Montana

USGS Publications Warehouse

Miller, C.H.

1979-01-01

Exploitation of vast coal and other resources in the Powder River Basin has caused recent, rapid increases in population and in commercial and residential development and has prompted land utilization studies. Two aspects of land utilization were studied for this report: (1) the seismic and geotechnical properties of a landslide and (2) the seismic, magnetic, and geotechnical properties of clinker deposits. (1) The landslide seismic survey revealed two layers in the slide area. The upper (low-velocity) layer is a relatively weak mantle of colluvium and unconsolidated and weathered bedrock that ranges in thickness from 3.0 to 7.5 m and has an average seismic velocity of about 390 m/s. It overlies high-velocity, relatively strong sedimentary bedrock that has velocities greater than about 1330 m/s. The low-velocity layer is also present at the other eight seismic refraction sites in the basin; a similar layer has also been reported in the Soviet Union in a landslide area over similar bedrock. The buried contact of the low- and high-velocity layers is relatively smooth and is nearly parallel with the restored topographic surface. There is no indication that any of the high-velocity layer (bedrock) has been displaced or removed. The seismic data also show that the shear modulus of the low-velocity layer is only about one-tenth that of the high-velocity layer and the shear strength (at failure) is only about one-thirtieth. Much of the slide failure is clearly in the shear mode, and failure is, therefore, concluded to be confined to the low-velocity layer. The major immediate factor contributing to landslide failure is apparently the addition of moisture to the low-velocity layer. The study implies that the low-velocity layer can be defined over some of the basin by seismic surveys and that they can help predict or delineate potential slides. Preventative actions that could then be taken include avoidance, dewatering, prevention of saturation, buttressing the toe, and unloading the head. The low-velocity layer is usually less than about 5 m thick and may be excavated by dozing, whereas the bedrock must be blasted. Thus, it would seem economically feasible to underpin a structure to nonweathered bedrock or, perhaps, to remove the low-velocity layer prior to construction. (2) Many coal beds in the Powder River Basin have burned along their outcrops, and the resulting intense heat has baked and fused the overlying clastic (sedimentary) rocks into clinkers. The clinkers are very magnetic and a buried edge of a single layer of burn can easily be located by magnetic prospecting methods. Location of the edge is very important in estimating unburned coal deposits, locating clinker quarries, and planning drilling of seismic reflection lines. The clinkers are very porous and highly fractured,-and seismic and geotechnical tests show that they have relatively low strength and competency. Many of the laboratory tests, however, are inherently biased because the clinkers are so highly fractured that only competent samples are selected. The laboratory tests, for example, show that clinkers must be loosened by heavy ripping tractors or blasting, whereas the field data and practical experience indicate that clinkers may be mined with light equipment. Heavy structures such as coal silos and bridge abutments may have to be sited on clinkers. However, differential settlement may occur, with failure in the shear mode, because chimneys of relatively greater strength occur among the weaker clinkers. Preliminary data indicate that the chimneys may be located by magnetic or possibly seismic surveys. Special foundation-preparation techniques could be used or, perhaps, the chimneys could be avoided altogether at a construction site.

The Use of the Visualisation of Multidimensional Data Using PCA to Evaluate Possibilities of the Division of Coal Samples Space Due to their Suitability for Fluidised Gasification

NASA Astrophysics Data System (ADS)

Jamróz, Dariusz; Niedoba, Tomasz; Surowiak, Agnieszka; Tumidajski, Tadeusz

2016-09-01

Methods serving to visualise multidimensional data through the transformation of multidimensional space into two-dimensional space, enable to present the multidimensional data on the computer screen. Thanks to this, qualitative analysis of this data can be performed in the most natural way for humans, through the sense of sight. An example of such a method of multidimensional data visualisation is PCA (principal component analysis) method. This method was used in this work to present and analyse a set of seven-dimensional data (selected seven properties) describing coal samples obtained from Janina and Wieczorek coal mines. Coal from these mines was previously subjected to separation by means of a laboratory ring jig, consisting of ten rings. With 5 layers of both types of coal (with 2 rings each) were obtained in this way. It was decided to check if the method of multidimensional data visualisation enables to divide the space of such divided samples into areas with different suitability for the fluidised gasification process. To that end, the card of technological suitability of coal was used (Sobolewski et al., 2012; 2013), in which key, relevant and additional parameters, having effect on the gasification process, were described. As a result of analyses, it was stated that effective determination of coal samples suitability for the on-surface gasification process in a fluidised reactor is possible. The PCA method enables the visualisation of the optimal subspace containing the set requirements concerning the properties of coals intended for this process.

Stochastic Modelling of the Hydraulic Anisotropy of Ash Impoundment Sediment

NASA Astrophysics Data System (ADS)

Slávik, Ivan

2017-12-01

In the case reported here the impoundments of a 400 MW coal heated power plant with an annual production of about 1.5 million tons of fuel ash are of the cross-valley type, operated by the simple and cheap „upstream method”. The aim of the research was to determine overall and local values of the permeability in horizontal as well as in vertical direction and the anisotropy of the thin-layered sedimented ash. The coal ashes are hydraulically transported through pipelines in form of a slurry and periodically floated on the beach of the impoundment. The ashes are deposited in the form of a thin-layered sediment, with random alternation of layers with a coarser or finer granularity. The ash impoundment sediment is anthropogenic sediment with horizontally laminated texture. Therefore, the sediment is anisotropic from the viewpoint of water seepage. The knowledge of the permeability and the seepage anisotropy of the sediment is a basic requirement for the design of an appropriate dewatering system. The seepage anisotropy of the ash sediment has been checked by means of stochastic modelling, based on the correlation between the effective grain diameter and the coefficient of permeability of the ash: the effective grain diameter and the thickness of individual layers have been proposed to be random events.

Spatio-Temporal Modelling of Dust Transport over Surface Mining Areas and Neighbouring Residential Zones.

PubMed

Matejicek, Lubos; Janour, Zbynek; Benes, Ludek; Bodnar, Tomas; Gulikova, Eva

2008-06-06

Projects focusing on spatio-temporal modelling of the living environment need to manage a wide range of terrain measurements, existing spatial data, time series, results of spatial analysis and inputs/outputs from numerical simulations. Thus, GISs are often used to manage data from remote sensors, to provide advanced spatial analysis and to integrate numerical models. In order to demonstrate the integration of spatial data, time series and methods in the framework of the GIS, we present a case study focused on the modelling of dust transport over a surface coal mining area, exploring spatial data from 3D laser scanners, GPS measurements, aerial images, time series of meteorological observations, inputs/outputs form numerical models and existing geographic resources. To achieve this, digital terrain models, layers including GPS thematic mapping, and scenes with simulation of wind flows are created to visualize and interpret coal dust transport over the mine area and a neighbouring residential zone. A temporary coal storage and sorting site, located near the residential zone, is one of the dominant sources of emissions. Using numerical simulations, the possible effects of wind flows are observed over the surface, modified by natural objects and man-made obstacles. The coal dust drifts with the wind in the direction of the residential zone and is partially deposited in this area. The simultaneous display of the digital map layers together with the location of the dominant emission source, wind flows and protected areas enables a risk assessment of the dust deposition in the area of interest to be performed. In order to obtain a more accurate simulation of wind flows over the temporary storage and sorting site, 3D laser scanning and GPS thematic mapping are used to create a more detailed digital terrain model. Thus, visualization of wind flows over the area of interest combined with 3D map layers enables the exploration of the processes of coal dust deposition at a local scale. In general, this project could be used as a template for dust-transport modelling which couples spatial data focused on the construction of digital terrain models and thematic mapping with data generated by numerical simulations based on Reynolds averaged Navier-Stokes equations.

Spatio-Temporal Modelling of Dust Transport over Surface Mining Areas and Neighbouring Residential Zones

PubMed Central

Matejicek, Lubos; Janour, Zbynek; Benes, Ludek; Bodnar, Tomas; Gulikova, Eva

2008-01-01

Projects focusing on spatio-temporal modelling of the living environment need to manage a wide range of terrain measurements, existing spatial data, time series, results of spatial analysis and inputs/outputs from numerical simulations. Thus, GISs are often used to manage data from remote sensors, to provide advanced spatial analysis and to integrate numerical models. In order to demonstrate the integration of spatial data, time series and methods in the framework of the GIS, we present a case study focused on the modelling of dust transport over a surface coal mining area, exploring spatial data from 3D laser scanners, GPS measurements, aerial images, time series of meteorological observations, inputs/outputs form numerical models and existing geographic resources. To achieve this, digital terrain models, layers including GPS thematic mapping, and scenes with simulation of wind flows are created to visualize and interpret coal dust transport over the mine area and a neighbouring residential zone. A temporary coal storage and sorting site, located near the residential zone, is one of the dominant sources of emissions. Using numerical simulations, the possible effects of wind flows are observed over the surface, modified by natural objects and man-made obstacles. The coal dust drifts with the wind in the direction of the residential zone and is partially deposited in this area. The simultaneous display of the digital map layers together with the location of the dominant emission source, wind flows and protected areas enables a risk assessment of the dust deposition in the area of interest to be performed. In order to obtain a more accurate simulation of wind flows over the temporary storage and sorting site, 3D laser scanning and GPS thematic mapping are used to create a more detailed digital terrain model. Thus, visualization of wind flows over the area of interest combined with 3D map layers enables the exploration of the processes of coal dust deposition at a local scale. In general, this project could be used as a template for dust-transport modelling which couples spatial data focused on the construction of digital terrain models and thematic mapping with data generated by numerical simulations based on Reynolds averaged Navier-Stokes equations. PMID:27879911

Structural geology of Amazonian-aged layered sedimentary deposits in southwest Candor Chasma, Mars

USGS Publications Warehouse

Okubo, C.H.

2010-01-01

The structural geology of an outcropping of layered sedimentary deposits in southwest Candor Chasma is mapped using two adjacent high-resolution (1 m/pixel) HiRISE digital elevation models and orthoimagery. Analysis of these structural data yields new insight into the depositional and deformational history of these deposits. Bedding in non-deformed areas generally dips toward the center of west Candor Chasma, suggesting that these deposits are basin-filling sediments. Numerous kilometer-scale faults and folds characterize the deformation here. Normal faults of the requisite orientation and length for chasma-related faulting are not observed, indicating that the local sediments accumulated after chasma formation had largely ceased in this area. The cause of the observed deformation is attributed to landsliding within these sedimentary deposits. Observed crosscutting relationships indicate that a population of sub-vertical joints are the youngest deformational structures in the area. The distribution of strain amongst these joints, and an apparently youthful infill of sediment, suggests that these fractures have been active in the recent past. The source of the driving stress acting on these joints has yet to be fully constrained, but the joint orientations are consistent with minor subsidence within west Candor Chasma.

Elaboration of new ceramic microfiltration membranes from mineral coal fly ash applied to waste water treatment.

PubMed

Jedidi, Ilyes; Saïdi, Sami; Khemakhem, Sabeur; Larbot, André; Elloumi-Ammar, Najwa; Fourati, Amine; Charfi, Aboulhassan; Salah, Abdelhamid Ben; Amar, Raja Ben

2009-12-15

This work aims to develop a new mineral porous tubular membrane based on mineral coal fly ash. Finely ground mineral coal powder was calcinated at 700 degrees C for about 3 h. The elaboration of the mesoporous layer was performed by the slip-casting method using a suspension made of the mixture of fly-ash powder, water and polyvinyl alcohol (PVA). The obtained membrane was submitted to a thermal treatment which consists in drying at room temperature for 24 h then a sintering at 800 degrees C. SEM photographs indicated that the membrane surface was homogeneous and did not present any macrodefects (cracks, etc...). The average pore diameter of the active layer was 0.25 microm and the thickness was around 20 microm. The membrane permeability was 475 l/h m(2) bar. This membrane was applied to the treatment of the dying effluents generated by the washing baths in the textile industry. The performances in term of permeate flux and efficiency were determined and compared to those obtained using a commercial alumina microfiltration membrane. Almost the same stabilised permeate flux was obtained (about 100 l h(-1)m(-2)). The quality of permeate was almost the same with the two membranes: the COD and color removal was 75% and 90% respectively.

Borehole sampling of fracture populations - compensating for borehole sampling bias in crystalline bedrock aquifers, Mirror Lake, Grafton County, New Hampshire

USGS Publications Warehouse

McDonald, G.D.; Paillet, Frederick L.; Barton, C.C.; Johnson, C.D.

1997-01-01

The clustering of orientations of hydraulically conductive fractures in bedrock at the Mirror Lake, New Hampshire fractured rock study site was investigated by comparing the orientations of fracture populations in two subvertical borehole arrays with those mapped on four adjacent subvertical roadcuts. In the boreholes and the roadcuts, the orientation of fracture populations appears very similar after borehole data are compensated for undersampling of steeply dipping fractures. Compensated borehole and pavement fracture data indicate a northeast-striking population of fractures with varying dips concentrated near that of the local foliation in the adjacent rock. The data show no correlation between fracture density (fractures/linear meter) and distance from lithologic contacts in both the boreholes and the roadcuts. The population of water-producing borehole fractures is too small (28 out of 610 fractures) to yield meaningful orientation comparisons. However, the orientation of large aperture fractures (which contains all the producing fractures) contains two or three subsidiary clusters in orientation frequency that are not evident in stereographic projections of the entire population containing all aperture sizes. Further, these subsidiary orientation clusters do not coincide with the dominant (subhorizontal and subvertical) regional fracture orientations.

Multiphase boudinage: a case study of amphibolites in marble in the Naxos migmatite core

NASA Astrophysics Data System (ADS)

Virgo, Simon; von Hagke, Christoph; Urai, Janos L.

2018-02-01

In multiply deformed terrains multiphase boudinage is common, but identification and analysis of these is difficult. Here we present an analysis of multiphase boudinage and fold structures in deformed amphibolite layers in marble from the migmatitic centre of the Naxos metamorphic core complex. Overprinting between multiple boudinage generations is shown in exceptional 3-D outcrop. We identify five generations of boudinage, reflecting the transition from high-strain high-temperature ductile deformation to medium- to low-strain brittle boudins formed during cooling and exhumation. All boudin generations indicate E-W horizontal shortening and variable direction of bedding parallel extension, evolving from subvertical extension in the earliest boudins to subhorizontal N-S extension during exhumation. Two phases of E-W shortening can be inferred, the first associated with lower crustal synmigmatic convergent flow and the second associated with exhumation and N-S extension, possibly related to movement of the North Anatolian Fault.

Evaluation of engineering properties for the use of leached brown coal ash in soil covers.

PubMed

Mudd, Gavin M; Chakrabarti, Srijib; Kodikara, Jayantha

2007-01-31

The need to engineer cover systems for the successful rehabilitation or remediation of a wide variety of solid wastes is increasing. Some common applications include landfills, hazardous waste repositories, or mine tailings dams and waste rock/overburden dumps. The brown coal industry of the Latrobe Valley region of Victoria, Australia, produces significant quantities of coal ash and overburden annually. There are some site-specific acid mine drainage (AMD) issues associated with overburden material. This needs to be addressed both during the operational phase of a project and during rehabilitation. An innovative approach was taken to investigate the potential to use leached brown coal ash in engineered soil covers on this overburden dump. The basis for this is two-fold: first, the ash has favourable physical characteristics for use in cover systems (such as high storage capacity/porosity, moderately low permeability, and an ability to act as a capillary break layer generating minimal leachate or seepage); and second, the leachate from the ash is mildly alkaline (which can help to mitigate and reduce the risk of AMD). This paper will review the engineering issues involved in using leached brown coal ash in designing soil covers for potentially acid-forming overburden dumps. It presents the results of laboratory work investigating the technical feasibility of using leached brown coal ash in engineered solid waste cover systems.

Surface modification to improve fireside corrosion resistance of Fe-Cr ferritic steels

DOEpatents

Park, Jong-Hee; Natesan, Krishnamurti; Rink, David L.

2010-03-16

An article of manufacture and a method for providing an Fe--Cr ferritic steel article of manufacture having a surface layer modification for corrosion resistance. Fe--Cr ferritic steels can be modified to enhance their corrosion resistance to liquid coal ash and other chemical environments, which have chlorides or sulfates containing active species. The steel is modified to form an aluminide/silicide passivating layer to reduce such corrosion.

The Study Of Soil And Agrochemical Features Of Zonal Soils Of Coal Mining Enterprises In Kemerovo Region

NASA Astrophysics Data System (ADS)

Yakovchenko, M. A.; Kosolapova, A. A.; Ermolaev, V. A.

2017-01-01

The paper represents the results of the study of soil and agrochemical features of zonal soils: the grain-size composition, the content of humus, phosphorus and potassium, and heavy metals, the reaction of soil solution of the territory of the open-pit coal mine No12 of Kemerovo region in the areas of the working enterprise. The species composition of the lignose and herbaceous vegetation of the undisturbed territories has been studied. It has been revealed that the fertile soil layer of the studied areas of the open-pit coal mine is characterized as fertile but can’t be removed and stored because the surface of the whole area under study is forest-covered very much, rumpled, there are gullies and a lot of wind-fallen trees.

Simulation of reduction of iron-oxide-carbon composite pellets in a rotary hearth furnace

NASA Astrophysics Data System (ADS)

Halder, Sabuj

The primary motivation of this work is to evaluate a new alternative ironmaking process which involves the combination of a Rotary Hearth Furnace (RHF) with an iron bath smelter. This work is concerned primarily, with the productivity of the RHF. It is known that the reduction in the RHF is controlled by chemical kinetics of the carbon oxidation and wustite reduction reactions as well as by heat transfer to the pellet surface and within the pellet. It is heat transfer to the pellet which limits the number of layers of pellets in the pellet bed in the RHF and thus, the overall productivity. Different types of carbon like graphite, coal-char and wood charcoal were examined. Part of the research was to investigate the chemical kinetics by de-coupling it from the influence of heat and mass transfer. This was accomplished by carrying out reduction experiments using small iron-oxide-carbon powder composite mixtures. The reaction rate constants were determined by fitting the experimental mass loss with a mixed reaction model. This model accounts for the carbon oxidation by CO2 and wustite reduction by CO, which are the primary rate controlling surface-chemical reactions in the composite system. The reaction rate constants have been obtained using wustite-coal-char powder mixtures and wustite-wood-charcoal mixtures. The wustite for these mixtures was obtained from two iron-oxide sources: artificial porous analytical hematite (PAH) and hematite ore tailings. In the next phase of this study, larger scale experiments were conducted in a RHF simulator using spherical composite pellets. Measurement of the reaction rates was accomplished using off-gas analysis. Different combinations of raw materials for the pellets were investigated. These included artificial ferric oxide as well as naturally existing hematite and taconite ores. Graphite, coal-char and wood-charcoal were the reductants. Experiments were conducted using a single layer, a double layer and a triple layer of composite pellets to look into the different aspects associated with multi-layer reduction in the RHF. The reduced pellets were examined for morphology and phase distribution using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) analysis. Efforts were made to interpret the differences in the observed rates from one kind of pellet to the other on the grounds of chemical kinetics of the carbon oxidation and wustite reduction reactions and the issues of external and internal heat transport to and within the pellets. It was concluded from the experiments that in the ore containing pellets, wood-charcoal appeared to be a faster reductant than coal-char. However, in the PAH containing pellets, the reverse was found to be true. This is because of the internal heat transport limitations imposed by two factors (a) lower thermal conductivity of wood-charcoal in comparison to coal-char and (b) swelling of the PAH-Wood-Charcoal pellets during the initial heat-up stage. For the same type of reductant, hematite containing pellets were observed to reduce faster than taconite containing pellets. This is in accordance with the higher reducibility of hematite because of development of internal porosity due to cracking and fissure formation during the Fe2O3 to Fe 3O4 transformation stage. This is however, absent during the reduction of taconite, which is primarily Fe3O4. The PAH-Wood-Charcoal pellets were found to undergo significant amounts of swelling under low temperature conditions. This behavior of the PAH-Wood-Charcoal pellets of a certain layer impeded the external heat transport to the lower layer and consequently, resulted in a relatively lower reduction rate for a multi-layer bed. The volume change phenomena associated with the reduction of composites were also studied. Volume changes influence the external heat transport, especially to the lower layers of a multi-layer bed. The volume change of the different kinds of composite pellets was studied as a function of reduction temperature and time. Empirical correlations were developed associating the volume shrinkage to the fractional mass loss of the pellets. The estimation of the change in the amount of external heat transport with varying pellet sizes for a particular layer of a multi-layer bed was obtained by conducting heat transport tests using inert low carbon steel spheres. The experimental temperature data for the spheres of different layers was interpreted using a simple mathematical model. It was found through this exercise, that if the spheres of the top layer of the bed shrink by 30%, the external heat transfer to the second layer increases by almost 6 times. This is because of the decrease in the shielded area of the second layer due to the decreasing size of the top layer spheres. If the average degree of reduction targeted in a RHF is reduced from 95% to about 70% by coupling the RHF with a bath smelter, the productivity of the RHF can be enhanced by 1.5 to 2 times. The use of a 2 or 3 layer bed was found to be far superior to that of a single layer for higher productivities under the current experimental conditions. Sometimes, a 2 layer bed is more advantageous than a 3 layer bed, as was found to be the case with hematite-wood-charcoal pellets. The choice of the optimal number of layers depends upon several factors like pellet size, kind of pellet and shrinking characteristics of the pellet.

Comparison of litter decomposition in a natural versus coal-slurry pond reclaimed as a wetland

USGS Publications Warehouse

Taylor, J.; Middleton, B.A.

2004-01-01

Decomposition is a key function in reclaimed wetlands, and changes in its rate have ramifications for organic-matter accumulation, nutrient cycling, and production. The purpose of this study was to compare leaf litter decomposition rates in coal-slurry ponds vs. natural wetlands on natural floodplain wetlands in Illinois, USA. The rate of decomposition was slower in the natural wetland vs. the coal pond (k=0.0043??0.0008 vs. 0.0066??0.0011, respectively); the soil of the natural wetland was more acidic than the coal pond in this study (pH=5.3 vs. 7.9, respectively). Similarly, higher organic matter levels were related to lower pH levels, and organic matter levels were seven-times higher in the natural wetland than in the coal pond. The coal slurry pond was five years old at the time of the study, while the natural oxbow wetland was older (more than 550 years). The coal-slurry pond was originally a floodplain wetland (slough); the downstream end was blocked with a stoplog structure and the oxbow filled with slurry. The pattern of decomposition for all species in the coal pond was the same as in the natural pond; Potomogeton nodosus decomposed more quickly than Phragmites australis, and both of these species decomposed more quickly than either Typha latifolia or Cyperus erythrorhizos (k=0.0121??0.0008, 0.0051??0.0006, 0.0024??0.0001, 0-0024??0.0004, respectively). Depending on how open or closed the system is to outside inputs, decomposition rate regulates other functions such as production, nutrient cycling, organic-layer accumulation in the soil, and the timing and nature of delivery of detritus to the food chain. ?? 2004 John Wiley and Sons, Ltd.

Investigation of MHD flow structure and fluctuations by potassium lineshape fitting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, L.E.

1993-12-31

Multiple Potassium D-line emission absorption spectra from a high temperature, coal-fired flow have been fit to a radiative transfer, boundary layer flow model. The results of fitting spectra from the aerodynamic duct of the Department of Energy Coal-Fired Flow Facility provide information about the thickness and shape of the thermal boundary layer and the bulk potassium seed atom density in a simulated magnetohydrodynamic channel flow. Probability distribution functions for the entire set of more than six thousand spectra clearly indicate the typical values and magnitude of fluctuations for the flow: core temperature of 2538 {plus_minus} 20 K, near wall temperaturemore » of 1945 {plus_minus} 135 K, boundary layer width of about 1 cm, and potassium seed atom density of (5.1 {plus_minus} 0.8)x 10{sup 22}/m{sup 3}. Probability distribution functions for selected times during the eight hours of measurements indicate occasional periods of unstable combustion. In addition, broadband particle parameters during the unstable start of the test may be related to differing particle and gas temperatures. The results clearly demonstrate the ability of lineshape fitting to provide valuable data for diagnosing the high speed turbulent flow.« less

Application of Laser Scanning for Creating Geological Documentation

NASA Astrophysics Data System (ADS)

Buczek, Michał; Paszek, Martyna; Szafarczyk, Anna

2018-03-01

A geological documentation is based on the analyses obtained from boreholes, geological exposures, and geophysical methods. It consists of text and graphic documents, containing drilling sections, vertical crosssections through the deposit and various types of maps. The surveying methods (such as LIDAR) can be applied in measurements of exposed rock layers, presented in appendices to the geological documentation. The laser scanning allows obtaining a complete profile of exposed surfaces in a short time and with a millimeter accuracy. The possibility of verifying the existing geological cross-section with laser scanning was tested on the example of the AGH experimental mine. The test field is built of different lithological rocks. Scans were taken from a single station, under favorable measuring conditions. The analysis of the signal intensity allowed to divide point cloud into separate geological layers. The results were compared with the geological profiles of the measured object. The same approach was applied to the data from the Vietnamese hard coal open pit mine Coc Sau. The thickness of exposed coal bed deposits and gangue layers were determined from the obtained data (point cloud) in combination with the photographs. The results were compared with the geological cross-section.

Phenols as chemical fossils in coals. [Book chapter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bimer, J.; Given, P.H.; Raj, S.

It is generally considered that vitrinite, the principal maceral in most coals, represents coalified, partly decayed wood. Hence lignin should be one of the important precursors to the vitrinites in coals. Accordingly, it would be interesting to know whether any chemical fossils related to lignin could be found in coals. The purpose of this paper is to report what we believe to be a successful search for such fossils. The experimental approach exploited a degradation reaction developed in a study of soil humic acids by Burges et al. This reaction involves a reductive degradation with sodium amalgam and hot water.more » Thin layer chromatography of the ether soluble part of the product (yield, about 20%) showed the presence of a number of phenols and phenolic acids, most of whose structures bore obvious relationships to known microbial and chemical degradation products of lignin but some to the A ring of flavonoids. Humic acids can be extracted from peats and lignites but not from bituminous coals. However, oxidation of bituminous coals with aqueous performic acid generates in high yield (80 to 110% by weight) materials that closely resemble humic acids. The Burges reductive degradation was applied to humic acids extracted from some peats and lignites, and produced by oxidation of a number of bituminous coals. A number of identifications of products were made originally by gas chromatography with co-injection of standards. In this preliminary publication the experimental procedures are described and a sufficient selection of the data are given to show what was found by co-injection and later confirmed by mass spectrometry.« less

Sulfidation of 310 stainless steel at sulfur potentials encountered in coal conversion systems

NASA Technical Reports Server (NTRS)

Rao, D. B.; Nelson, H. G.

1976-01-01

The sulfidation of SAE 310 stainless steel was carried out in gas mixtures of hydrogen and hydrogen sulfide over a range of sulfur potentials anticipated in advanced coal gasification processes. The kinetics, composition, and morphology of sulfide scale formation were studied at a fixed temperature of 1,065 K over a range of sulfur potentials from .00015 Nm to the -2nd power to 900 Nm to the -2nd power. At all sulfur potentials investigated, the sulfide scales were found to be multilayered. The relative thickness of the individual layers as well as the composition was found to depend on the sulfur potential. The reaction was found to obey the parabolic rate law after an initial transient period. Considerably longer transient periods were found to be due to unsteady state conditions resulting from compositional variations in the spinel layer. The sulfur pressure dependence on the parabolic rate constant was found to best fit the equation K sub p equals const. (P sub S2) to the 1/nth power, where n equals 3.7. The growth of the outer layers was found to be primarily due to the diffusion of metal ions, iron being the predominant species. The inner layer growth was due to the dissociation of the primary product at the alloy scale interface and depended on the activity of chromium.

Synthesis, anion exchange, and delamination of Co-Al layered double hydroxide: assembly of the exfoliated nanosheet/polyanion composite films and magneto-optical studies.

PubMed

Liu, Zhaoping; Ma, Renzhi; Osada, Minoru; Iyi, Nobuo; Ebina, Yasuo; Takada, Kazunori; Sasaki, Takayoshi

2006-04-12

This paper describes a systematic study on the synthesis, anion exchange, and delamination of Co-Al layered double hydroxide (LDH), with the aim of achieving fabrication and clarifying the properties of LDH nanosheet/polyanion composite films. Co-Al-CO3 LDH hexagonal platelets of 4 mum in lateral size were synthesized by the urea method under optimized reaction conditions. The as-prepared CO3(2-)-LDH was converted to Cl- -LDH by treating with a NaCl-HCl mixed solution, retaining its high crystallinity and hexagonal platelike morphology. LDHs intercalated with a variety of anions (such as NO3-, ClO4-, acetate, lactate, dodecyl sulfate, and oleate) were further prepared from Cl- -LDH via an anion-exchange process employing corresponding salts. Exchanged products in various anion forms were found to show different delamination behaviors in formamide. Among them, best results were observed for NO3- -LDH in terms of the exfoliating degree and the quality of the exfoliated nanosheets. The delamination gave a pink transparent suspension containing well-defined nanosheets with lateral sizes of up to 2 microm. The resulting nanosheets were assembled layer-by-layer with an anionic polymer, poly(sodium styrene 4-sulfonate) (PSS), onto quartz glass substrates to produce composite films. Magnetic circular dichroism (MCD) measurements revealed that the assembled multilayer films exhibited an interesting magneto-optical response.

Conditions for the formation and atmospheric dispersion of a toxic, heavy gas layer during thermal metamorphism of coal and evaporite deposits by sill intrusion

NASA Astrophysics Data System (ADS)

Storey, Michael; Hankin, Robin K. S.

2010-05-01

There is compelling evidence for massive discharge of volatiles, including toxic species, into the atmosphere at the end of the Permian. It has been argued that most of the gases were produced during thermal metamorphism of coal and evaporite deposits in the East Siberia Tunguska basin following sill intrusion (Retallack and Jahren, 2008; Svensen et al., 2009). The release of the volatiles has been proposed as a major cause of environmental and extinction events at the end of the Permian, with venting of carbon gases and halocarbons to the atmosphere leading to global warming and atmospheric ozone depletion (Svensen et al., 2009) Here we consider the conditions required for the formation and dispersion of toxic, heavier than air, gas plumes, made up of a mixture of CO2, CH4, H2S and SO2 and formed during the thermal metamorphism of C- and S- rich sediments. Dispersion models and density considerations within a range of CO2/CH4 ratios and volatile fluxes and temperatures, for gas discharge by both seepage and from vents, allow the possibility that following sill emplacement much of the vast East Siberia Tunguska basin was - at least intermittently - covered by a heavy, toxic gas layer that was unfavorable for life. Dispersion scenarios for a heavy gas layer beyond the Siberian region during end-Permian times will be presented. REFERENCES G. J. Retallack and A. H. Jahren, Methane release from igneous intrusion of coal during Late Permian extinction events, Journal of Geology, volume 116, 1-20, 2008 H. Svensen et al., Siberian gas venting and the end-Permian environmental crisis, Earth and Planetary Science Letters, volume 277, 490-500, 2009

Hydrogeology, groundwater flow, and groundwater quality of an abandoned underground coal-mine aquifer, Elkhorn Area, West Virginia

USGS Publications Warehouse

Kozar, Mark D.; McCoy, Kurt J.; Britton, James Q.; Blake, B.M.

2017-01-01

The Pocahontas No. 3 coal seam in southern West Virginia has been extensively mined by underground methods since the 1880’s. An extensive network of abandoned mine entries in the Pocahontas No. 3 has since filled with good-quality water, which is pumped from wells or springs discharging from mine portals (adits), and used as a source of water for public supplies. This report presents results of a three-year investigation of the geology, hydrology, geochemistry, and groundwater flow processes within abandoned underground coal mines used as a source of water for public supply in the Elkhorn area, McDowell County, West Virginia. This study focused on large (> 500 gallon per minute) discharges from the abandoned mines used as public supplies near Elkhorn, West Virginia. Median recharge calculated from base-flow recession of streamflow at Johns Knob Branch and 12 other streamflow gaging stations in McDowell County was 9.1 inches per year. Using drainage area versus mean streamflow relationships from mined and unmined watersheds in McDowell County, the subsurface area along dip of the Pocahontas No. 3 coal-mine aquifer contributing flow to the Turkey Gap mine discharge was determined to be 7.62 square miles (mi2), almost 10 times larger than the 0.81 mi2 surface watershed. Results of this investigation indicate that groundwater flows down dip beneath surface drainage divides from areas up to six miles east in the adjacent Bluestone River watershed. A conceptual model was developed that consisted of a stacked sequence of perched aquifers, controlled by stress-relief and subsidence fractures, overlying a highly permeable abandoned underground coal-mine aquifer, capable of substantial interbasin transfer of water. Groundwater-flow directions are controlled by the dip of the Pocahontas No. 3 coal seam, the geometry of abandoned mine workings, and location of unmined barriers within that seam, rather than surface topography. Seven boreholes were drilled to intersect abandoned mine workings in the Pocahontas No. 3 coal seam and underlying strata in various structural settings of the Turkey Gap and adjacent down-dip mines. Geophysical logging and aquifer testing were conducted on the boreholes to locate the coal- mine aquifers, characterize fracture geometry, and define permeable zones within strata overlying and underlying the Pocahontas No. 3 coal-mine aquifer. Water levels were measured monthly in the wells and showed a relatively static phreatic zone within subsided strata a few feet above the top of or within the Pocahontas No. 3 coal-mine aquifer (PC3MA). A groundwater-flow model was developed to verify and refine the conceptual understanding of groundwater flow and to develop groundwater budgets for the study area. The model consisted of four layers to represent overburden strata, the Pocahontas No. 3 coal-mine aquifer, underlying fractured rock, and fractured rock below regional drainage. Simulation of flow in the flooded abandoned mine entries using highly conductive layers or zones within the model, was unable to realistically simulate interbasin transfer of water. Therefore it was necessary to represent the coal-mine aquifer as an internal boundary condition rather than a contrast in aquifer properties. By representing the coal-mine aquifer with a series of drain nodes and optimizing input parameters with parameter estimation software, model errors were reduced dramatically and discharges for Elkhorn Creek, Johns Knob Branch, and other tributaries were more accurately simulated. Flow in the Elkhorn Creek and Johns Knob Branch watersheds is dependent on interbasin transfer of water, primarily from up dip areas of abandoned mine workings in the Pocahontas No. 3 coal-mine aquifer within the Bluestone River watershed to the east. For the 38th, 70th, and 87th percentile flow duration of streams in the region, mean measured groundwater discharge was estimated to be 1.30, 0.47, and 0.39 cubic feet per square mile (ft3/s/mi2

Highly dispersed catalysts for coal liquefaction. Quarterly report No. 9, August 23, 1993--November 22, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirschon, A.S.; Wilson, R.B.

We analyzed two sets of liquefaction experiments, one involved the liquefaction of Black Thunder Coal with the corresponding recycle vehicle, and the second set of liquefaction runs involved the liquefaction of Argonne North Dakota Lignite. We compared coal conversions of Black Thunder coal and recycle solvent using Fe(CO){sub 5} and carbon monoxide/hydrogen atmospheres and a MolyVanL molybdenum catalyst under a hydrogen atmosphere. We also continued our investigation of the effect of water on the conversions. We found that addition of water seemed to decrease the amount of oils; we determined the effect of water with the recycle solvent alone, (nomore » coal added) under similar conditions, and again produced a decrease in oil yields. FIMS analyses of the hexane and toluene soluble fractions seem to indicate that in the experiment when water was added, a considerable amount of light material remained behind in the toluene layer, suggesting that somehow the addition of water decreased the amount of extracted material, perhaps by increasing the amount of polarity of the product. When the conversion was conducted with the MolyVanL molybdenum catalyst a good quality product in terms of lower viscosity was produced; however, conversions to THF soluble material was not increased. We believe the molybdenum catalyst hydrogenated the recycle vehicle rather than effectively converted the coal. In order to eliminate the effect of solvent we have often conducted experiments in an inert solvent with Argonne coals. We conducted several coal conversions experiments using an Argonne North Dakota lignite. We compared several dispersed Fe catalysts and in addition, a nickel catalyst. We investigated nickel as a catalyst since we believe this metal may be more effective in decarboxylating low rank coals. Consistent with this premise we found that the nickel catalyst gave the highest conversions.« less

Regeneratively cooled coal combustor/gasifier with integral dry ash removal

DOEpatents

Beaufrere, Albert H.

1983-10-04

A coal combustor/gasifier is disclosed which produces a low or medium combustion gas for further combustion in modified oil or gas fired furnaces or boilers. Two concentric shells define a combustion volume within the inner shell and a plenum between them through which combustion air flows to provide regenerative cooling of the inner shell for dry ash operation. A fuel flow and a combustion air flow having opposed swirls are mixed and burned in a mixing-combustion portion of the combustion volume and the ash laden combustion products flow with a residual swirl into an ash separation region. The ash is cooled below the fusion temperature and is moved to the wall by centrifugal force where it is entrained in the cool wall boundary layer. The boundary layer is stabilized against ash re-entrainment as it is moved to an ash removal annulus by a flow of air from the plenum through slots in the inner shell, and by suction on an ash removal skimmer slot.

GIS Representation of Coal-Bearing Areas in Africa

USGS Publications Warehouse

Merrill, Matthew D.; Tewalt, Susan J.

2008-01-01

The African continent contains approximately 5 percent of the world's proven recoverable reserves of coal (World Energy Council, 2007). Energy consumption in Africa is projected to grow at an annual rate of 2.3 percent from 2004 through 2030, while average consumption in first-world nations is expected to rise at 1.4 percent annually (Energy Information Administration, 2007). Coal reserves will undoubtedly continue to be part of Africa's energy portfolio as it grows in the future. A review of academic and industrial literature indicates that 27 nations in Africa contain coal-bearing rock. South Africa accounts for 96 percent of Africa's total proven recoverable coal reserves, ranking it sixth in the world. This report is a digital compilation of information on Africa's coal-bearing geology found in the literature and is intended to be used in small scale spatial investigations in a Geographic Information System (GIS) and as a visual aid for the discussion of Africa's coal resources. Many maps of African coal resources often include points for mine locations or regional scale polygons with generalized borders depicting basin edges. Point locations are detailed but provide no information regarding extent, and generalized polygons do not have sufficient detail. In this dataset, the polygons are representative of the actual coal-bearing lithology both in location and regional extent. Existing U.S. Geological Survey (USGS) digital geology datasets provide the majority of the base geologic polygons. Polygons for the coal-bearing localities were clipped from the base geology that represented the age and extent of the coal deposit as indicated in the literature. Where the 1:5,000,000-scale geology base layer's ages conflicted with those in the publications, polygons were generated directly from the regional African coal maps (1:500,000 scale, approximately) in the published material. In these cases, coal-bearing polygons were clipped to the literature's indicated coal extent, without regard to the underlying geology base or topographic constraints. Indication of the presence of African coal is based on multiple sources. However, the quality of the sources varies and there is often disagreement in the literature. This dataset includes the rank, age, and location of coal in Africa as well as the detailed source information responsible for each coal-bearing polygon. The dataset is not appropriate for use in resource assessments of any kind. Attributes necessary for tasks, such as number of coal seams, thickness of seams, and depth to coal are rarely provided in the literature and accordingly not represented in this data set. Small-scale investigations, representations and display uses are most appropriate for this product. This product is the first to show coal distribution as bounded by actual geologic contacts for the entire African continent. In addition to the spatial component of this dataset, complete references to source material are provided for each polygon, making this product a useful first step resource in African coal research. Greater detail regarding the creation of this dataset as well as the sources used is provided in the metadata file for the Africa_coal.shp file.

Gone viral? Heard the buzz? A guide for public health practitioners and researchers on how Web 2.0 can subvert advertising restrictions and spread health information.

PubMed

Freeman, B; Chapman, S

2008-09-01

Many nations have banned or curtailed advertising of potentially harmful products to protect public health, particularly in the area of chronic disease control. The growth in Internet-based marketing techniques is subverting these advertising regulations. Explosive rises in use of social networking and user-generated content websites is further fuelling product promotion through electronic media. In contrast, there is a very limited body of public health research on these "new media" advertising methods. This paper provides an overview of these advertising methods and details examples relevant to chronic disease control. There is a vast untapped potential for health practitioners and researchers to exploit these same media for health promotion.

Fabrication and characteristics of excellent current spreading GaN-based LED by using transparent electrode-insulator-semiconductor structure

NASA Astrophysics Data System (ADS)

Qi, Chenglin; Huang, Yang; Zhan, Teng; Wang, Qinjin; Yi, Xiaoyan; Liu, Zhiqiang

2017-08-01

GaN-based vertical light-emitting-diodes (V-LEDs) with an improved current injection pattern were fabricated and a novel current injection pattern of LEDs which consists of electrode-insulator-semiconductor (EIS) structure was proposed. The EIS structure was achieved by an insulator layer (20-nm Ta2O5) deposited between the p-GaN and the ITO layer. This kind of EIS structure works through a defect-assisted tunneling mechanism to realize current injection and obtains a uniform current distribution on the chip surface, thus greatly improving the current spreading ability of LEDs. The appearance of this novel current injection pattern of V-LEDs will subvert the impression of the conventional LEDs structure, including simplifying the chip manufacture technology and reducing the chip cost. Under a current density of 2, 5, 10, and 25 A/cm2, the luminous uniformity was better than conventional structure LEDs. The standard deviation of power density distribution in light distribution was 0.028, which was much smaller than that of conventional structure LEDs and illustrated a huge advantage on the current spreading ability of EIS-LEDs. Project supported by the Natural Science Foundation of China (Nos. 61306051, 61306050) and the National High Technology Program of China (No. 2014AA032606).

Thickness-, Composition-, and Magnetic-Field-Dependent Complex Impedance Spectroscopy of Granular-Type-Barrier Co/Co-Al2O3/Co MTJs

NASA Astrophysics Data System (ADS)

Tuan, Nguyen Anh; Anh, Nguyen Tuan; Nga, Nguyen Tuyet; Tue, Nguyen Anh; Van Cuong, Giap

2016-06-01

The alternating-current (ac) electrical properties of granular-type-barrier magnetic tunnel junctions (GBMTJs) based on Co/Co x (Al2O3)1- x ( t)/Co trilayer structures have been studied using complex impedance spectroscopy (CIS). Their CIS characteristics were investigated in external magnetic fields varying from 0 kOe to 3 kOe as a function of Co composition x at 10 at.%, 25 at.%, and 35 at.%, with barrier layer thickness t of 20 nm to 90 nm. The influence of these factors on the behaviors of the ac impedance response of the GBMTJs was deeply investigated and attributed to the dielectric or conducting nature of the Co-Al2O3 barrier layer. The most remarkable typical phenomena observed in these behaviors, even appearing paradoxical, include lower impedance for thicker t for each given x, a declining trend of Z with increasing x, a clear decrease of Z with H, and especially a partition of Z into zones according to the H value. All these effects are analyzed and discussed to demonstrate that diffusion-type and mass-transfer-type phenomena can be inferred from processes such as spin tunneling and Coulomb or spin blockade in the Co-Al2O3 barrier layer.

The application of Co-Al-hydrotalcite as a novel additive of positive material for nickel-metal hydride secondary cells

NASA Astrophysics Data System (ADS)

Feng, Zhaobin; Yang, Zhanhong; Yang, Bin; Zhang, Zheng; Xie, Xiaoe

2014-11-01

Co-Al-CO3 layered double hydroxide (LDH) with the different Co/Al molar ration is synthesized by hydrothermal method and investigated as an additive for positive material of the Ni-MH cells. The Fourier transform infrared spectra (FT-IR), scanning electron microscopy (SEM) and X-ray diffraction (XRD) show the Co-Al-LDH with Co/Al = 4:1 (molar ration) is well-crystallized and hexagon structure. The electrochemical performances of the nickel electrode added with different Co/Al molar ration Co-Al-LDH, the pure nickel electrode and the nickel electrode added with CoO are investigated by the cyclic voltammograms (CV), galvanostatic charge-discharge measurements, and AC electrochemical impedance spectroscopy (EIS). Compared with the pure nickel electrode and the nickel electrode added with CoO, the nickel electrode added with Co/Al = 4:1 (molar ration) Co-Al-LDH has higher discharge capacity and more stable cycling performances. This cell can undergo at least 400 charge-discharge cycles at constant current of 1 C. The discharge capacity of this cell remains about 287 mAh g-1 after the 400th cycle. Meanwhile, compared with the pure electrode, the nickel electrode added with Co/Al = 4:1 (molar ration) Co-Al-LDH possess a higher rate capability to meet the needs of high-storage applications.

Green technologies in natural and synthetic surfaces use for dumps reclamation

NASA Astrophysics Data System (ADS)

Klimkina, Iryna; Fedotov, Viacheslav; Heilmeier, Hermann

2016-04-01

Last 50 years coal dumps reclamation in Ukraine was based on two- or three-layer models. These models use a fertile substratum underneath a black soil (chernozem) layer 0.5 m thick (Model 1) or 0.70-1 m thick (Model 2). Model 3 has 3 layers. The deepest layer is a substrate which is phytotoxic or unfavourable for crop growth (coal-bearing substrates with a high content of pyrite, saline substrates). The second layers acts as a protective shield and consist of loess (0.5 m). The third is the layer of fertile chernozem (0.3-0.8 m). However, due to the situation of a shortage of fertile soils, a lack of nutrient elements in the waste rock, and a moisture deficit with strong rock acidification, it is considered important to develop new non-traditional reclamation methods based on the geo-synthetic materials used in conjunction with sowing lawn grasses or grass seeds inside. The geogrids and biogeotextiles made from natural materials such as hemp, flax, jute, coconut and other plant biopolymer fibers are recommended for bioremediation. The biodegradable carcass of reclamation covering materials stabilises the slopes, effectively restraints the soil particles from leaching and blowing, and prevents wash-out of the plant seeds, as well as protecting them from being eaten by animals. The research object of the presented work was the coal dumps of sulfide rocks in Western Donbass (Ukraine). These rocks are characterized by low level of the maximum hygroscopic moisture (4.3%) and moisture content not available for plant growth (5-6%). Also the rock has an average level of salinity, mainly of the sulphate type. The main goal of the study was to justify the use of some non-traditional materials such as burlap (jute cloth), agricultural fibers (light non-woven material from polypropylene fiber of spun-bond type) and a padding of polyester in the capacity of a geosynthetic substrate as a basis for the mixed grass crop that enable a reduction in the bioremediation costs (in comparison with traditional methods of covering by fertile soil layer) and the arrangement of lawn roll. A mixture of grass crops was used that included three types of grass seeds which were sown in the condition of hydroponics with settled tap water in a floating poly-foam frame on the one- and two-layer (with grass seeds inside) substrates of the above-mentioned materials. The best results, in terms of seed germination, root and above-ground parts of the plants length, were obtained with a single layer of jute burlap on which practically all germinated seeds reached a high degree of seedlings mass and root productivity similar to indices of growth mixtures in greenhouses. As a mulch of organic ingredients a wide range of crop residues, namely wheat straw, corn stalks, sunflower stalks and husks, and others, can be used.

Occurrence and origin of minerals in a chamosite-bearing coal of Late Permian age, Zhaotong, Yunnan, China

USGS Publications Warehouse

Dai, S.; Chou, C.-L.

2007-01-01

The minerals found in the no.5 coal (Late Permian) from the Zhaotong Coalfield, Yunnan Province, southwestern China, have been examined and found to consist mainly of kaolinite, pyrite, chamosite, quartz, and calcite, with trace amounts of illite and mixed-layer illite-smectite. The proportion of chamosite in clay minerals ranges from 32 to 56 wt%, with an average of 46 wt%. Chamosite is distributed not only in collodetrinite, but also occurs as cell fillings in fusinite, semifusinite, and telinite. The high content and mode of occurrence of chamosite in this mine indicate its formation by interaction of kaolinite with Fe-Mg-rich fluids during early diagenesis. Except for a minor amount of terfigenous quartz, most quartz is of authigenic origin and formed from kaolinite desilication. The calcite content of the no. 5 coal is 1.4-6.3% (with an average of 3%) and is distributed in collodetrinite and as cell fillings of coal-forming plants. Calcite originated from seawater invasion during peat accumulation. Pyrite occurs in several ways: as massive, framboidal, isolated enhedral/ anhedral, and euhedral forms. In addition, the presence of a large amount of pyritized red algae provides strong evidence of seawater invasion during peat accumulation. The red algae may have played an important role in the enrichment of sulfur in the coal. The characteristic assemblage of minerals in this mine resulted from a unique basinal environment in which the mineral matter was derived from a basaltic source region, volcanic activity, and seawater transgression during coal formation.

Surface Morphology of Active Normal Faults in Hard Rock: Implications for the Mechanics of the Asal Rift, Djibouti

NASA Astrophysics Data System (ADS)

Pinzuti, P.; Mignan, A.; King, G. C.

2009-12-01

Mechanical stretching models have been previously proposed to explain the process of continental break-up through the example of the Asal Rift, Djibouti, one of the few places where the early stages of seafloor spreading can be observed. In these models, deformation is distributed starting at the base of a shallow seismogenic zone, in which sub-vertical normal faults are responsible for subsidence whereas cracks accommodate extension. Alternative models suggest that extension results from localized magma injection, with normal faults accommodating extension and subsidence above the maximum reach of the magma column. In these magmatic intrusion models, normal faults have dips of 45-55° and root into dikes. Using mechanical and kinematics concepts and vertical profiles of normal fault scarps from an Asal Rift campaign, where normal faults are sub-vertical on surface level, we discuss the creation and evolution of normal faults in massive fractured rocks (basalt). We suggest that the observed fault scarps correspond to sub-vertical en echelon structures and that at greater depth, these scarps combine and give birth to dipping normal faults. Finally, the geometry of faulting between the Fieale volcano and Lake Asal in the Asal Rift can be simply related to the depth of diking, which in turn can be related to magma supply. This new view supports the magmatic intrusion model of early stages of continental breaking.

'We talk, we do not have shame': addressing stigma by reconstructing identity through enhancing social cohesion among female sex workers living with HIV in the Dominican Republic.

PubMed

Carrasco, Maria Augusta; Barrington, Clare; Kennedy, Caitlin; Perez, Martha; Donastorg, Yeycy; Kerrigan, Deanna

2017-05-01

This study explores social cohesion as a strategy used by female sex workers to address layered HIV and sex work-related stigma. Data derive from a thematic analysis of 23 in-depth interviews and 2 focus groups with female sex workers living with HIV enrolled in a multi-level HIV/STI prevention, treatment and care intervention in Santo Domingo, Dominican Republic. Drawing on Foucault's conceptualisation of modern power, discipline and resistance, we argue that social cohesion provides the psychosocial space (of trust, solidarity and mutual aid) to subvert oppressive societal norms, enabling the reconstruction of identity. Among study participants, identity reconstruction happened through the production, repetition and performance of new de-stigmatised narratives that emerged and were solidified through collective interaction. Findings highlight that enabling the collective reconstruction of identity through social cohesion - rather than solely attempting to change individual beliefs - is a successful approach to addressing stigma.

Myxoma virus in the European rabbit: interactions between the virus and its susceptible host.

PubMed

Stanford, Marianne M; Werden, Steven J; McFadden, Grant

2007-01-01

Myxoma virus (MV) is a poxvirus that evolved in Sylvilagus lagomorphs, and is the causative agent of myxomatosis in European rabbits (Oryctolagus cuniculus). This virus is not a natural pathogen of O. cuniculus, yet is able to subvert the host rabbit immune system defenses and cause a highly lethal systemic infection. The interaction of MV proteins and the rabbit immune system has been an ideal model to help elucidate host/poxvirus interactions, and has led to a greater understanding of how other poxvirus pathogens are able to cause disease in their respective hosts. This review will examine how MV causes myxomatosis, by examining a selection of the identified immunomodulatory proteins that this virus expresses to subvert the immune and inflammatory pathways of infected rabbit hosts.

Coal Mining, Germany

NASA Image and Video Library

2001-08-01

This simulated natural color ASTER image in the German state of North Rhine Westphalia covers an area of 30 by 36 km, and was acquired on August 26, 2000. On the right side of the image are 3 enormous opencast coalmines. The Hambach opencast coal mine has recently been brought to full output capacity through the addition of the No. 293 giant bucket wheel excavator. This is the largest machine in the world; it is twice as long as a soccer field and as tall as a building with 30 floors. To uncover the 2.4 billion tons of brown coal (lignite) found at Hambach, five years were required to remove a 200-m-thick layer of waste sand and to redeposit it off site. The mine currently yields 30 million tons of lignite annually, with annual capacity scheduled to increase to 40 million tons in coming years. The image is centered at 51 degrees north latitude, 6.4 degrees east longitude. http://photojournal.jpl.nasa.gov/catalog/PIA02676

Graphene-oxide-supported CuAl and CoAl layered double hydroxides as enhanced catalysts for carbon-carbon coupling via Ullmann reaction

NASA Astrophysics Data System (ADS)

Ahmed, Nesreen S.; Menzel, Robert; Wang, Yifan; Garcia-Gallastegui, Ainara; Bawaked, Salem M.; Obaid, Abdullah Y.; Basahel, Sulaiman N.; Mokhtar, Mohamed

2017-02-01

Two efficient catalyst based on CuAl and CoAl layered double hydroxides (LDHs) supported on graphene oxide (GO) for the carbon-carbon coupling (Classic Ullmann Homocoupling Reaction) are reported. The pure and hybrid materials were synthesised by direct precipitation of the LDH nanoparticles onto GO, followed by a chemical, structural and physical characterisation by electron microscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), surface area measurements and X-ray photoelectron spectroscopy (XPS). The GO-supported and unsupported CuAl-LDH and CoAl-LDH hybrids were tested over the Classic Ullman Homocoupling Reaction of iodobenzene. In the current study CuAl- and CoAl-LDHs have shown excellent yields (91% and 98%, respectively) at very short reaction times (25 min). GO provides a light-weight, charge complementary and two-dimensional material that interacts effectively with the 2D LDHs, in turn enhancing the stability of LDH. After 5 re-use cycles, the catalytic activity of the LDH/GO hybrid is up to 2 times higher than for the unsupported LDH.

Facile synthesis of three dimensional hierarchical Co-Al layered double hydroxides on graphene as high-performance materials for supercapacitor electrode.

PubMed

Hao, Jinhui; Yang, Wenshu; Zhang, Zhe; Lu, Baoping; Ke, Xi; Zhang, Bailin; Tang, Jilin

2014-07-15

A facile simple hydrothermal method combined with a post-solution reaction is developed to grow interconnected three dimensional (3D) hierarchical Co-Al layered double hydroxides (LDHs) on reduced graphene oxide (rGO). The obtained 3D hierarchical rGO-LDHs are characterized by field emission scanning electron microscopy, X-ray diffraction, and X-ray photo-electron spectroscopy. As LDHs nanosheets directly grow on the surface of rGO via chemical covalent bonding, the rGO could provide facile electron transport paths in the electrode for the fast Faradaic reaction. Moreover, benefiting from the rational 3D hierarchical structural, the rGO-LDHs demonstrate excellent electrochemical properties with a combination of high charge storage capacitance, fast rate capability and stable cycling performance. Remarkably, the 3D hierarchical rGO-LDHs exhibit specific capacitance values of 599 F g(-1) at a constant current density of 4 A g(-1). The rGO-LDHs also show high charge-discharge reversibility with an efficiency of 92.4% after 5000 cycles. Copyright © 2014 Elsevier Inc. All rights reserved.

Studies of Low-Current Back-Discharge in Point-Plane Geometry with Dielectric Layer

NASA Astrophysics Data System (ADS)

Jaworek, Anatol; Rajch, Eryk; Krupa, Andrzej; Czech, Tadeusz; Lackowski, Marcin

2006-01-01

The paper presents results of spectroscopic investigations of back-discharges generated in the point-plane electrode geometry in ambient air at atmospheric pressure, with the plane electrode covered with a dielectric layer. Fly ash from an electrostatic precipitator of a coal-fired power plant was used as the dielectric layer in these investigations. The discharges for positive and negative polarities of the needle electrode were studied by measuring optical emission spectra at two regions of the discharge: near the needle electrode and dielectric layer surface. The visual forms of the discharge were recorded and correlated with the current-voltage characteristics and optical emission spectra. The back-arc discharge was of particular interest in these studies due to its detrimental effects it causes in electrostatic precipitators.

Technology, Privacy and the Democratic Process.

ERIC Educational Resources Information Center

Gandy, Oscar H., Jr.; Simmons, Charles E.

1986-01-01

Argues that advances in information technology, especially capacities to collect and combine data for marketing purposes, subvert protections of individual privacy and weaken the influence of the individual in democracy. (MS)

A conceptual hydrodynamic model of a geological discontinuity in hard rock aquifers: Example of a quartz reef in granitic terrain in South India

NASA Astrophysics Data System (ADS)

Dewandel, Benoît; Lachassagne, Patrick; Zaidi, Faisal K.; Chandra, Subash

2011-08-01

SummaryThe structure and hydrodynamic properties of geological discontinuities and of a deeply weathered granite aquifer near these structures are described on the basis of geological, geophysical and hydrodynamic investigations in two sites of South India located along a 20-40-m-wide quartz reef intruding a weathered Archean biotite granite. One of the two sites also comprises a metre-wide dolerite dyke. Weathering processes appear to be at the origin of fissures development and of a related enhanced local hydraulic conductivity, both in the quartz reef and in the surrounding granite. The weathering profile in the granite (saprolite and fissured layer) is characterized by an abrupt deepening of the weathered layers in the granite near the contact and in the quartz reef itself. Therefore, the weathering profile shows a 'U'-shape geometry with, among others, the verticalization of the granite's fissured layer. The hydraulic conductivity of this verticalized layer is on average 5 × 10 -6 m/s and storativity about 10 -3 (-). The hydraulic conductivity of the fissured quartz is 4-6 × 10 -6 m/s and its storativity about 3-5 × 10 -4 (-). Both media are also characterized by a matrix hydraulic conductivity (10 -7-10 -9 m/s) and by a significant heterogeneity in hydrodynamic properties that generates preferential flow paths along the sub-vertical fissures parallel to the reef axis. A special attention has been paid for characterizing this heterogeneity. The weathering of the dolerite dyke, however, results in a local low hydraulic conductivity, which consequently does not enhance either the thickness of weathered granite layers or its hydraulic conductivity. The obtained results complete the conceptual hydrogeological model developed for weathered granite aquifers in characterizing the relationships between weathering processes and hydrodynamic properties near geological discontinuities.

Numerical modeling of a subsidence induced by underground coal gasification, including thermal effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stephenson, D.E.; Dass, S.T.; Shaw, D.E.

During normal coal extraction roof collapse is controlled, thermal effects are absent and existing data is useless for the formation of numerical models of underground coal gasification(PGU). Thermal deformation occurs during PGU to the extent that rock is deformed, the roof collapses, rock settles, and changes occur in the water-bearing layers, and so forth. As PGU progresses, changes occur in the geometry, size, and other characteristics of the volume of the reaction. Data derived from plastic coal in New Mexico (USA) is used to construct a numerical model. This coal was bedded at a depth of 259 meters where itmore » was stratified throughout a mixture of rock. Core drilling was conducted and a geological column was constructed to induce a PGY combustion front with temperatures of 900 degrees. Temperatures of 600 and 300 degrees were encountered 6.1 and 12.2 meters from the front, respectively. A short distance from the front, in a direction away from the placticized material, the temperature of the rock matched the 27 degree temperature in the surrounding rock. Correlational relationships were obtained for stress in rock under different conditions and these correlations were used to appraise the effect of heat on the rock. It was suggested that the heating of rock did, at times, serve to support the roof rock. Similarly, during periods of cooling, this effect lessened. Comparative and optimal test results are appraised with the aid of the numerical model.« less

Historical record of black carbon in urban soils and its environmental implications.

PubMed

He, Yue; Zhang, Gan-Lin

2009-10-01

Energy use in urbanization has fundamentally changed the pattern and fluxes of carbon cycling, which has global and local environmental impacts. Here we have investigated organic carbon (OC) and black carbon (BC) in six soil profiles from two contrast zones in an ancient city (Nanjing) in China. BC in soils was widely variable, from 0.22 to 32.19 g kg(-1). Its average concentration in an ancient residential area (Zone 1) was, 0.91 g kg(-1), whereas in Zone 2, an industrial and commercial area, the figure was 8.62 g kg(-1). The ratio of BC/OC ranged from 0.06 to 1.29 in soil profiles, with an average of 0.29. The vertical distribution of BC in soil is suggested to reflect the history of BC formation from burning of biomass and/or fossil fuel. BC in the surface layer of soils was mainly from traffic emission (especially from diesel vehicles). In contrast, in cultural layers BC was formed from historical coal use. The contents of BC and the ratio of BC/OC may reflect different human activities and pollution sources in the contrasting urban zones. In addition, the significant correlation of heavy metals (Cu, Pb, and Zn) with BC contents in some culture layers suggests the sorption of the metals by BC or their coexistence resulted from the coal-involved smelting.

The coal-forming plants of the upper part of the Lower Cretaceous Starosuchan Formation (Partizansk Basin, South Primorye region)

NASA Astrophysics Data System (ADS)

Bugdaeva, E. V.; Markevich, V. S.; Volynets, E. B.

2014-05-01

The plant remains and palynological assemblages are studied in detail in the section of the coal-bearing upper part of the Aptian Starosuchan Formation near the village of Molchanovka (Partizansk Basin, South Primorye region). On the basis of the light and electron microscopic study of the disperse cuticles, it was established that the coals are mostly composed of remains of taxodialean Elatides asiatica (Yok.) Krassil., subordinate Miroviaceae, rare ginkgoalean Pseudotorellia sp., and bennettite Nilssoniopteris rithidorachis (Krysht.) Krassil. The spores Gleicheniidites and pollen Taxodiaceaepollenites are dominant in the palynospectrum of the coal interlayer. It was found that dominant taxodialeans and gleicheniaceous ferns with less abundant Miroviaceae, ginkgoaleans, and rare bennettites occurred in the Aptian swamp communities of the Partizansk basin. Shoots and leaves of Elatides asiatica, fronds of Birisia onychioides (Vassil. et K.-M.) Samyl., are dominant in the burials of plants from the clastic rocks. The fragments of leaves of Nilssoniopteris, scale-leaved conifers, and Ginkgo ex gr. adiantoides are rare. The disperse cuticle of these layers mostly includes Pseudotorellia sp.; however, its remains in burials were not found. The spores Laevigatosporites are dominant in the palynospectra from the clastic interlayers. Ginkgocycadophytus and taxa close to Pinaceae are plentiful among the pollen of gymnosperms.

Greatly increased use of fly ash in hydraulic cement concrete (HCC) for pavement layers and transportation structures - volume I.

DOT National Transportation Integrated Search

2012-03-01

The purpose of this phase is to evaluate the past, current and future trends of use of fly ash in concrete and restrictions to its use. The American Coal Ash Association (ACAA) conducts an annual survey of fly ash production and use. Typically on an ...

DOE Office of Scientific and Technical Information (OSTI.GOV)

L.P. Noskova

The products of the alkaline hydrolysis of wax isolated from brown coal from the Sergeevskoe deposit were studied using chromatography and IR and NMR spectroscopy. It was found that hydrocarbons, alcohols, acids, and a representative fraction of unsaponifiable esters were the constituents of wax. High-molecular-weight fatty alcohols and acids were identified as the constituents of wax with the use of thin-layer chromatography.

Key Technologies and Applications of Gas Drainage in Underground Coal Mine

NASA Astrophysics Data System (ADS)

Zhou, Bo; Xue, Sheng; Cheng, Jiansheng; Li, Wenquan; Xiao, Jiaping

2018-02-01

It is the basis for the long-drilling directional drilling, precise control of the drilling trajectory and ensuring the effective extension of the drilling trajectory in the target layer. The technology can be used to complete the multi-branch hole construction and increase the effective extraction distance of the coal seam. The gas drainage and the bottom grouting reinforcement in the advanced area are realized, and the geological structure of the coal seam can be proved accurately. It is the main technical scheme for the efficient drainage of gas at home and abroad, and it is applied to the field of geological structure exploration and water exploration and other areas. At present, the data transmission method is relatively mature in the technology and application, including the mud pulse and the electromagnetic wave. Compared with the mud pulse transmission mode, the electromagnetic wave transmission mode has obvious potential in the data transmission rate and drilling fluid, and it is suitable for the coal mine. In this paper, the key technologies of the electromagnetic wave transmission mode are analyzed, including the attenuation characteristics of the electromagnetic transmission channel, the digital modulation scheme, the channel coding method and the weak signal processing technology. A coal mine under the electromagnetic wave drilling prototype is developed, and the ground transmission experiments and down hole transmission test are carried out. The main work includes the following aspects. First, the equivalent transmission line method is used to establish the electromagnetic transmission channel model of coal mine drilling while drilling, and the attenuation of the electromagnetic signal is measured when the electromagnetic channel measured. Second, the coal mine EM-MWD digital modulation method is developed. Third, the optimal linear block code which suitable for EM-MWD communication channel in coal mine is proposed. Fourth, the noise characteristics of well near horizontal directional drilling are analyzed, and the multi-stage filter method is proposed to suppress the natural potential and strong frequency interference signal. And the weak electromagnetic communication signal is extracted from the received signal. Finally, the detailed design of the electromagnetic wave while drilling is given.

Regional-scale geomechanical impact assessment of underground coal gasification by coupled 3D thermo-mechanical modeling

NASA Astrophysics Data System (ADS)

Otto, Christopher; Kempka, Thomas; Kapusta, Krzysztof; Stańczyk, Krzysztof

2016-04-01

Underground coal gasification (UCG) has the potential to increase the world-wide coal reserves by utilization of coal deposits not mineable by conventional methods. The UCG process involves combusting coal in situ to produce a high-calorific synthesis gas, which can be applied for electricity generation or chemical feedstock production. Apart from its high economic potentials, UCG may induce site-specific environmental impacts such as fault reactivation, induced seismicity and ground subsidence, potentially inducing groundwater pollution. Changes overburden hydraulic conductivity resulting from thermo-mechanical effects may introduce migration pathways for UCG contaminants. Due to the financial efforts associated with UCG field trials, numerical modeling has been an important methodology to study coupled processes considering UCG performance. Almost all previous UCG studies applied 1D or 2D models for that purpose, that do not allow to predict the performance of a commercial-scale UCG operation. Considering our previous findings, demonstrating that far-field models can be run at a higher computational efficiency by using temperature-independent thermo-mechanical parameters, representative coupled simulations based on complex 3D regional-scale models were employed in the present study. For that purpose, a coupled thermo-mechanical 3D model has been developed to investigate the environmental impacts of UCG based on a regional-scale of the Polish Wieczorek mine located in the Upper Silesian Coal Basin. The model size is 10 km × 10 km × 5 km with ten dipping lithological layers, a double fault and 25 UCG reactors. Six different numerical simulation scenarios were investigated, considering the transpressive stress regime present in that part of the Upper Silesian Coal Basin. Our simulation results demonstrate that the minimum distance between the UCG reactors is about the six-fold of the coal seam thickness to avoid hydraulic communication between the single UCG reactors. Fault reactivation resulting from fault shear and normal displacements is discussed under consideration of potentially induced seismicity. Here, the coupled simulation results indicate that seismic hazard during UCG operation remains negligible with a seismic moment magnitude of MW < 3.

Engineering Graphene Films from Coal

NASA Astrophysics Data System (ADS)

Vijapur, Santosh H.

Graphene is a unique material with remarkable properties suitable for a wide array of applications. Chemical vapor deposition (CVD) is a simple technique for synthesis of large area and high quality graphene films on various metal substrates. Among the metal substrates, copper has been shown to be an excellent support for the growth of graphene films. Traditionally, hydrocarbon gases are used for the graphene synthesis via CVD. Unconventional solid carbon sources such as various polymers and food waste have also shown great potential for synthesis of graphene films. Coal is one such carbon enriched and abundantly available unconventional source. Utilization of coal as a carbon source to synthesize large area, transparent, and high quality few-layer graphene films via CVD has been demonstrated in the present work. Hydrocarbon gases are released as products of coal pyrolysis at temperatures ≥400 °C. This study hypothesized that, these hydrocarbon gases act as precursors for the synthesis of graphene films on the copper substrate. Hence, atmospheric pressure CVD and low temperature of 400 °C were utilized initially for the production of graphene films. These conditions were suitable for the formation of amorphous carbon (a-C) films but not crystalline graphene films that were the objective of this work. The synthesized a-C films on the copper substrate were shown to be uniform and transparent with large surface area. The thickness and surface roughness of the a-C films were determined to have typical values of 5 nm and 0.55 nm, respectively. The a-C film has >95 % optical transmittance and sheet resistivity of 0.6 MO sq-1. These values are comparable to other carbon thin films synthesized at higher temperatures. Further, the a-C films were transferred onto any type of substrate such as silicon wafer and titanium foil, and can be utilized for diverse applications. However, crystalline graphene films were not produced by implementing atmospheric pressure CVD and low temperature operation. Annealing of copper support was required to remove the oxide layer present on its surface and low pressure operation was demonstrated to be suitable for crystalline graphene film formation. The CVD system and the synthesis procedure were modified to address these issues. This was done by increasing the synthesis temperature, incorporating a vacuum pump for low pressure operation, and implementing two step procedure of annealing the copper substrate followed by subsequent coal pyrolysis for the synthesis of crystalline graphene films. The synthesized few layer graphene films were uniform and continuous with thickness in the range of 3-7 nm. The optical transmittance and electrical conductivity measurements demonstrated that the graphene films have >95 % transparency and sheet resistivity of 5.0 kO sq-1, respectively. An investigation of growth mechanism of coal derived graphene films synthesized via CVD was conducted utilizing spectroscopy, microscopy, and chromatography techniques. Gas collection was performed at the graphene synthesis conditions utilizing the CVD reactor without vacuum in operation. Various gases released as products of coal pyrolysis in the CVD reactor were collected and analyzed using gas chromatography. The analysis showed the presence of methane, ethane, ethene, propane, propene, carbon monoxide, and carbon dioxide as coal pyrolysis products. The hydrocarbon gases act as precursors for graphene growth. Raman spectroscopy, selected area electron diffraction (SAED), and X-ray photoelectron spectroscopy (XPS) confirmed the formation of crystalline graphene films at 1055 °C and 18-30 min synthesis. The growth mechanism involves copper catalyzed reaction to produce amorphous carbon film within the first few minutes of synthesis. Raman spectroscopy and SAED validated that lower synthesis times (6-12 min) produced hybrid amorphous carbon films. This is followed by hydrogen catalyzed graphitization of the underlying carbon film to form graphene domains. Optical microscopy and Raman spectra demonstrated the formation of these oval shaped graphene domains as synthesis time was increased (18-30 min). The graphene films are formed by growth and merging of these graphene domains on the copper substrate. The growth mechanism of coal derived crystalline graphene films is presented in the current work.

A Neanderthal lower molar from Stajnia Cave, Poland.

PubMed

Dąbrowski, P; Nowaczewska, W; Stringer, C B; Compton, T; Kruszyński, R; Nadachowski, A; Stefaniak, K; Urbanowski, M

2013-04-01

The primary aim of this study was to conduct a taxonomic assessment of the second of three isolated human teeth found in the Stajnia Cave (north of the Carpathians, Poland) in 2008. The specimen was located near a human tooth (S5000), which was identified by Urbanowski et al. (2010) as a Neanderthal permanent upper molar. Both of these teeth were excavated from the D2 layer, which belongs to the D stratigraphic complex comprising the archaeological assemblage associated with the Micoquian tradition. An Ursus spelaeus bone and Mammuthus primigenius tooth that were also excavated from the D2 layer were dated to >49,000 years BP (by AMS (14)C) and 52.9 ka BP (by U-Th), respectively. The sediment overlying stratigraphic complex D was dated to 45.9 ka BP by the OSL method. The S4300 tooth is a lower first or second permanent molar belonging to an individual other than that who once possessed the S5000 tooth. The S4300 tooth exhibits a combination of traits typical of Neanderthal lower molars, including a mid-trigonid crest, large anterior fovea, taurodontism and subvertical grooves on the interproximal face, indicating that this tooth belonged to a Neanderthal individual. The S4300 tooth from Stajnia Cave is one of the oldest human remains found in Poland. Copyright © 2013 Elsevier GmbH. All rights reserved.

Ocular findings in coal miners diagnosed with pneumoconiosis.

PubMed

Ayar, Orhan; Orcun Akdemir, Mehmet; Erboy, Fatma; Yazgan, Serpil; Hayri Ugurbas, Suat

2017-06-01

Our study aimed at evaluating ocular findings and structural changes in coal mine workers who were chronically exposed to coal mine dust and diagnosed with pneumoconiosis. Ocular findings of 161 eyes of 81 patients diagnosed with pneumoconiosis who had previously worked or are currently working in coal mines were analyzed. Forty-six coal mine workers and sex matched healthy people (n = 20) participated in the study. Workers who had early changes of pneumoconiosis were included in Group 1 (n = 17), workers diagnosed with pneumoconiosis were included in Group 2 (n = 29), and healthy subjects were included in Group 3 (n = 20). Outcome measures were the difference in peripapillary retinal nerve fiber layer (RNFL) thickness, choroidal thickness (CT), central macular thickness (CMT) and tear function tests between the groups. RNFL thickness values in Group 1 and 2 were lower than in Group 3, the control group, in all quadrants except the temporal quadrant. However, there was no statistically significant difference in peripapillary RNFL thickness values in any quadrants among the three groups (p > 0.05). Central subfoveal choroidal thickness and CMT measurements were thinner in Group 1 and 2 than in the control group. However, this difference among groups was not statistically significant (p > 0.05). Mean schirmer's test result was 8.8 ± 1.6 mm in group 1, 7.1 ± 1.8 mm in Group 2 and 11.5 ± 3.6 mm in the control group. Mean tear break up time (BUT) test result was 7.1 ± 1.3 seconds (sec) in Group 1, 6.5 ± 1.8 sec in Group 2 and 10.4 ± 2.9 s in the control group. The Schirmer's test and BUT test results were both statistically significantly lower in coal mine workers (Group 1 and 2) compared to the control group. Group 1 and Group 2 did not show statistically significant difference in terms of Schirmer's test and BUT test results. The association between pneumoconiosis and coal mine dust contiguity is thought to be due to the effect of coal dust by producing chronic inflammation. In addition, there are several trace elements in coal dust which are toxic to vital tissues. In this study, ocular findings suggest that systemic levels of trace elements and chronic inflammation may not reach to a level that influences ocular structures. Nonetheless, tear functions seem to be affected in coal mine workers. This study suggests that the systemic effect of coal mine dust in ocular structures is not evident. However, direct contact with coal mine and fume leads to a decrease in tear function tests.

Hi-Tech Unrevealed.

ERIC Educational Resources Information Center

Vernooy, D. Andrew; Alter, Kevin

2001-01-01

Presents design features of the University of Texas' Applied Computational Engineering and Sciences Building and discusses how institutions can guide the character of their architecture without subverting the architects' responsibility to confront their contemporary culture in a critical manner. (GR)

Lower and lower Middle Pennsylvanian coal palynofloras, southwestern Virginia

USGS Publications Warehouse

Eble, C.F.

1996-01-01

Lower and lower Middle Pennsylvanian coals, recovered from an exploratory drilling program in southwestern Virginia, were analyzed for their palynomorph content. Results show them to be dominated by spores produced by arboreous lycopsids. Lycospora pellucida and Lycospora pusilla generally are the most common species, with others, namely Lycospora granulata, L. micropapillata and Lycospora orbicula being locally abundant. Densosporites, Cristatisporites, Radiizonates and Cingulizonates, representing small lycopsids, and Granulatisporites, produced by small ferns, and perhaps some pteridosperms typically are sub-dominant taxa. The recovered palynofloras are similar in overall composition making individual coal bed identification and correlation very difficult, if not impossible. However, the introduction and extinction of a few forms do assist the correlation of packages of strata, on both an intra- and interbasinal scale. Dictyotriletes bireticulatus is first observed in basal Lee Formation strata, at about the level of the Cove Creek coal bed. Radiizonates aligerans and R. striatus also appear more abundantly at this level, although some forms have been observed in older, Pocahontas Formation coals. This level essentially coincides with the Namurian C/Westphalian A boundary, based on plant megafossil evidence. Laevigatosporites minor, L. vulgaris, Endosporites globiformis, E. zonalis and Granasporites medius are first seen consistently just above the Sewell coal bed. Radiizonates aligerans, R. striatus and Densosporites irregularis are last seen in the early Middle Pennsylvanian, at about the level of the Splash Dam coal bed. Schulzospora rara occurs throughout Early and early Middle Pennsylvanian strata, and is last seen in the Manchester coal. The Manchester is directly overlain by the Betsie Shale, a widespread marine unit; the base of the Betsie marks the Westphalian A/B contact. When compared with palynomorph assemblage zonations published for the Western Interior, and Eastern Interior Basins, Early and early Middle Pennsylvanian palynofloras from the Central Appalachian Basin compare most favorably with early Morrowan strata. Analysis of bench samples indicates that Lycospora typically dominates basal and middle portions of Early and early Middle Pennsylvanian coals. More terminal layers often contain higher percentages of Granulatisporites (and related trilete, sphaerotriangular genera, e.g. Lophotriletes, Acanthotriletes, Deltoidspora) and Densosporites (and related trilete, crassicingulate genera, e.g. Cristatisporites, Cingulizonates, Radiizonates). This temporal change is consistently observed and may primarily reflect a water table change within the paleomires from consistently high (covered with water or at least water-logged most of the time) to intermittently low (occasional substrate exposure).

Brown coal maceral distributions in a modern domed tropical Indonesian peat and a comparison with maceral distributions in Middle Pennsylvanian–age Appalachian bituminous coal beds

USGS Publications Warehouse

Grady, William C.; Eble, Cortland F.; Neuzil, Sandra G.

1993-01-01

Analyses of modern Indonesian peat samples reveal that the optical characteristics of peat constituents are consistent with the characteristics of macerals observed in brown coal and, as found by previous workers, brown-coal maceral terminology can be used in the analysis of modern peat. A core from the margin and one from near the center of a domed peat deposit in Riau Province, Sumatra, reveal that the volume of huminite macerals representing well-preserved cell structures (red, red-gray, and gray textinite; ulminite; and corpo/textinite) decreases upward. Huminite macerals representing severely degraded (<20 microns) cellular debris (degraded textinite, attrinite, and densinite) increase uniformly from the base to the surface. Greater degradation of the huminite macerals in the upper peat layers in the interior of the deposit is interpreted to be the result of fungal activity that increased in response to increasingly aerobic conditions associated with the doming of the peat deposit. Aerobic conditions concurrent with the activities of fungi may result in incipient oxidation of the severely degraded huminite macerals. This oxidation could lead to the formation of degradosemifusinite, micrinite, and macrinite maceral precursors in the peat, which may become evident only upon coalification. The core at the margin was petrographically more homogeneous than the core from the center and was dominated by well-preserved huminite macerals except in the upper 1 m, which showed signs of aerobic degradation and was similar to the upper 1 m of the peat in the interior of the deposit.The Stockton and other Middle Pennsylvanian Appalachian coal beds show analogous vertical trends in vitrinite maceral composition. The succession from telocollinite-rich, bright coal lithotypes in the lower benches upward to thin-banded/matrix collinite and desmocollinite in higher splint coal benches is believed to reflect a progression similar to that from the well-preserved textinite macerals in the lower portions of the peat cores to severely fragmented and degraded cellular materials (degraded textinite, attrinite, and densinite) in the upper portions of the cores. This petrographic sequence from bright to splint coal in the Stockton and other Middle Pennsylvanian coal beds supports previous interpretations of an upward transition from planar to domed swamp accumulations.

Mathematical optimization techniques for managing selective catalytic reduction for a fleet of coal-fired power plants

NASA Astrophysics Data System (ADS)

Alanis Pena, Antonio Alejandro

Major commercial electricity generation is done by burning fossil fuels out of which coal-fired power plants produce a substantial quantity of electricity worldwide. The United States has large reserves of coal, and it is cheaply available, making it a good choice for the generation of electricity on a large scale. However, one major problem associated with using coal for combustion is that it produces a group of pollutants known as nitrogen oxides (NO x). NOx are strong oxidizers and contribute to ozone formation and respiratory illness. The Environmental Protection Agency (EPA) regulates the quantity of NOx emitted to the atmosphere in the United States. One technique coal-fired power plants use to reduce NOx emissions is Selective Catalytic Reduction (SCR). SCR uses layers of catalyst that need to be added or changed to maintain the required performance. Power plants do add or change catalyst layers during temporary shutdowns, but it is expensive. However, many companies do not have only one power plant, but instead they can have a fleet of coal-fired power plants. A fleet of power plants can use EPA cap and trade programs to have an outlet NOx emission below the allowances for the fleet. For that reason, the main aim of this research is to develop an SCR management mathematical optimization methods that, with a given set of scheduled outages for a fleet of power plants, minimizes the total cost of the entire fleet of power plants and also maintain outlet NO x below the desired target for the entire fleet. We use a multi commodity network flow problem (MCFP) that creates edges that represent all the SCR catalyst layers for each plant. This MCFP is relaxed because it does not consider average daily NOx constraint, and it is solved by a binary integer program. After that, we add the average daily NOx constraint to the model with a schedule elimination constraint (MCFPwSEC). The MCFPwSEC eliminates, one by one, the solutions that do not satisfy the average daily NOx constraint and the worst NH 3 slip until it finds the solution that satisfies that requirement. We introduce an algorithm called heuristic MCFPwSEC (HMCFPwSEC). When HMCFPwSEC algorithm starts, we calculate the cost of the edges estimating the average NH3 slip level, but after we have a schedule that satisfies the average daily NOx constraint and the worst NH3 slip, we update the cost of the edges with the average NH3 slip for this schedule. We repeat this process until we have the solution. Because HMCFPwSEC does not guarantee optimality, we compare its results with SGO, which is optimal, using computational experiments. The results between both models are very similar, the only important difference is the time to solve each model. Then, a fleet HMCFPwSEC (FHMCFPwSEC) uses HMCFPwSEC to create the SCR management plan for each plant of the fleet, with a discrete NOx emissions value for each plant. FHMCFPwSEC repeats this process with different discrete levels of NOx emissions, for each plant, in order to create a new problem with schedules with different cost and NO x emissions for each plant of the fleet. Finally, FHMCFPwSEC solves this new problem with a binary integer program, in order to satisfy a NO x emission value for the fleet that also minimizes the total cost for the fleet, and using each plant once. FHMCFPwSEC can work with single cut and also with multi-cut methods. Because FHMCFPwSEC does not guarantee optimality, we compare its results with fleet SGO (FSGO) using computational experiments. The results between both models are very similar, the only important difference is the time to solve each model. In the experiments, FHMCFPwSEC multi-cut targeting new layer always uses less time than FSGO.

A noise control package for vibrating screens1),2)

PubMed Central

Lowe, M. Jenae; Yantek, David S.; Yang, Junyi; Schuster, Kevin C.; Mechling, Jessie J.

2015-01-01

Hearing loss was the second-most common illness reported to the Mine Safety and Health Administration (MSHA) in 2009. Furthermore, between 2000 and 2010, 30% of all noise-related injury complaints reported to MSHA were for coal preparation plant employees. Previous National Institute for Occupational Safety and Health (NIOSH) studies have shown that vibrating screens are key noise sources to address in order to reduce coal preparation plant noise. In response, NIOSH researchers have developed a suite of noise controls for vibrating screens consisting of constrained layer damping (CLD) treatments, a tuned mechanism suspension, an acoustic enclosure, and spring inserts. Laboratory testing demonstrates that this noise control suite reduces the A-weighted sound power level of the vibrating screen by 6 dB. To provide a comparison to laboratory results and prove durability, field testing of two noise controls was performed on a vibrating screen in a working coal preparation plant. The spring inserts and CLD treatments were selected due to their ease of installation and practicability. Field testing of these controls yielded reductions that were comparable to laboratory results. PMID:26257468

Mapping the hydraulic connection between a coalbed and adjacent aquifer: example of the coal-seam gas resource area, north Galilee Basin, Australia

NASA Astrophysics Data System (ADS)

Jiang, Zhenjiao; Mariethoz, Gregoire; Schrank, Christoph; Cox, Malcolm; Timms, Wendy

2016-12-01

Coal-seam gas production requires groundwater extraction from coal-bearing formations to reduce the hydraulic pressure and improve gas recovery. In layered sedimentary basins, the coalbeds are often separated from freshwater aquifers by low-permeability aquitards. However, hydraulic connection between the coalbed and aquifers is possible due to the heterogeneity in the aquitard such as the existence of conductive faults or sandy channel deposits. For coal-seam gas extraction operations, it is desirable to identify areas in a basin where the probability of hydraulic connection between the coalbed and aquifers is low in order to avoid unnecessary loss of groundwater from aquifers and gas production problems. A connection indicator, the groundwater age indictor (GAI), is proposed, to quantify the degree of hydraulic connection. The spatial distribution of GAI can indicate the optimum positions for gas/water extraction in the coalbed. Depressurizing the coalbed at locations with a low GAI would result in little or no interaction with the aquifer when compared to the other positions. The concept of GAI is validated on synthetic cases and is then applied to the north Galilee Basin, Australia, to assess the degree of hydraulic connection between the Aramac Coal Measure and the water-bearing formations in the Great Artesian Basin, which are separated by an aquitard, the Betts Creek Beds. It is found that the GAI is higher in the western part of the basin, indicating a higher risk to depressurization of the coalbed in this region due to the strong hydraulic connection between the coalbed and the overlying aquifer.

Bacterial effectors target the plant cell nucleus to subvert host transcription.

PubMed

Canonne, Joanne; Rivas, Susana

2012-02-01

In order to promote virulence, Gram-negative bacteria have evolved the ability to inject so-called type III effector proteins into host cells. The plant cell nucleus appears to be a subcellular compartment repeatedly targeted by bacterial effectors. In agreement with this observation, mounting evidence suggests that manipulation of host transcription is a major strategy developed by bacteria to counteract plant defense responses. It has been suggested that bacterial effectors may adopt at least three alternative, although not mutually exclusive, strategies to subvert host transcription. T3Es may (1) act as transcription factors that directly activate transcription in host cells, (2) affect histone packing and chromatin configuration, and/or (3) target host transcription factor activity. Here, we provide an overview on how all these strategies may lead to host transcriptional re-programming and, as a result, to improved bacterial multiplication inside plant cells.

Wood chips for dust control on surface-mine haul roads

Treesearch

George P., Jr. Williams

1979-01-01

On a coal haul spur road where water sprinkling was the primary method of dust control, the duration of control was increased tenfold by covering the road surface with a layer of wood chips. The chip blanket prevented existing dust-size particles from being kicked up and swept into plumes by passing traffic, insulated the road surface against evaporation and protected...

Core-in-shell sorbent for hot coal gas desulfurization

DOEpatents

Wheelock, Thomas D.; Akiti, Jr., Tetteh T.

2004-02-10

A core-in-shell sorbent is described herein. The core is reactive to the compounds of interest, and is preferably calcium-based, such as limestone for hot gas desulfurization. The shell is a porous protective layer, preferably inert, which allows the reactive core to remove the desired compounds while maintaining the desired physical characteristics to withstand the conditions of use.

Speciation and pulmonary effects of acidic SO x formed on the surface of ultrafine zinc oxide aerosols

NASA Astrophysics Data System (ADS)

Amdur, Mary O.; Chen, Lung Chi; Guty, John; Lam, Hua Fuan; Miller, Patricia D.

Ultrafine metal oxides and SO 2 react during coal combustion or smelting operations to form primary emissions coated with an acidic SO x layer. A ZnO-SO 2-H 2O (mixed 500°C) system generates such particles to provide greatly needed information on both quantitative composition of the surface layer and its effects on the lung. Total S on the particles is related to ZnO concentration and is predominantly S VI. As a surface layer, 20 μg m -3 H 2SO 4 decreases pulmonary diffusing capacity in guinea pigs after four daily 3-h exposures and produces bronchial hypersensitivity following a single 1-h exposure. That 200 μg m -3 H 2SO 4 aerosols of equivalent particle size are needed to produce the same degree of bronchial hypersensitivity emphasizes the importance of the surface layer.

Carbothermic reduction behaviors of Ti-Nb-bearing Fe concentrate from Bayan Obo ore in China

NASA Astrophysics Data System (ADS)

Wang, Guang; Du, Ya-xing; Wang, Jing-song; Xue, Qing-guo

2018-01-01

To support the development of technology to utilize low-grade Ti-Nb-bearing Fe concentrate, the reduction of the concentrate by coal was systematically investigated in the present paper. A liquid phase formed when the Ti-Nb-bearing Fe concentrate/coal composite pellet was reduced at temperatures greater than 1100°C. The addition of CaCO3 improved the reduction rate when the slag basicity was less than 1.0 and inhibited the formation of the liquid phase. Mechanical milling obviously increased the metallization degree compared with that of the standard pellet when reduced under the same conditions. Evolution of the mineral phase composition and microstructure of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet at 1100°C were analyzed by X-ray diffraction and scanning electron microscopy-energy-dispersive spectroscopy. The volume shrinkage value of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet with a basicity of 1.0 was approximately 35.2% when the pellet was reduced at 1100°C for 20 min, which enhanced the external heat transfer to the lower layers when reduced in a practical rotary hearth furnace. The present work provides key parameters and mechanism understanding for the development of carbothermic reduction technology of a Ti-Nb-bearing Fe concentrate incorporated in a pyrometallurgical utilization flow sheet.

Friends World College, Bensalem, The College of the Potomac: Portrait of Three Experiments

ERIC Educational Resources Information Center

Jerome, Judson

1970-01-01

The experimental college must not only define new standards of quality education, but also the means to achieve it, and to defend itself against the educational establishment which it seeks to subvert. (Editor)

NORMATIVE SCIENCE: SUBVERTING DEVELOPMENT OF SOUND FISHERIES POLICY

EPA Science Inventory

Effectively resolving the typical fisheries policy issue requires an array of scientific information as part of the input provided to decision-makers. In my experience, the ability of scientists (and scientific information) to constructively inform fisheries policy deliberations...

Low cost hydrogen/novel membrane technology for hydrogen separation from synthesis gas, Phase 1. [Polyetherimide, cellulose acetate and ethylcellulose

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-01-01

The goal of this program is to develop polymer membranes useful in the preparation of hydrogen from coal-derived synthesis gas. During this quarter the first experiment were aimed at developing high performance composite membranes for the separation of hydrogen from nitrogen and carbon monoxide. Three polymers have been selected as materials for these membranes: polyetherimide cellulose acetate and ethylcellulose. This quarter the investigators worked on polyetherimide and cellulose acetate membranes. The overall structure of these membranes is shown schematically in Figure 1. As shown, a microporous support membrane is first coated with a high flux intermediate layer then with anmore » ultrathin permselective layer and finally, if necessary, a thin protective high flux layer. 1 fig., 4 tabs.« less

HIV-1 Nef hijacks clathrin coats by stabilizing AP-1:Arf1 polygons.

PubMed

Shen, Qing-Tao; Ren, Xuefeng; Zhang, Rui; Lee, Il-Hyung; Hurley, James H

2015-10-23

The lentiviruses HIV and simian immunodeficiency virus (SIV) subvert intracellular membrane traffic as part of their replication cycle. The lentiviral Nef protein helps viruses evade innate and adaptive immune defenses by hijacking the adaptor protein 1 (AP-1) and AP-2 clathrin adaptors. We found that HIV-1 Nef and the guanosine triphosphatase Arf1 induced trimerization and activation of AP-1. Here we report the cryo-electron microscopy structures of the Nef- and Arf1-bound AP-1 trimer in the active and inactive states. A central nucleus of three Arf1 molecules organizes the trimers. We combined the open trimer with a known dimer structure and thus predicted a hexagonal assembly with inner and outer faces that bind the membranes and clathrin, respectively. Hexagons were directly visualized and the model validated by reconstituting clathrin cage assembly. Arf1 and Nef thus play interconnected roles in allosteric activation, cargo recruitment, and coat assembly, revealing an unexpectedly intricate organization of the inner AP-1 layer of the clathrin coat. Copyright © 2015, American Association for the Advancement of Science.

Seismic properties investigation of the Springer Ranch landslide, Powder River basin, Wyoming

USGS Publications Warehouse

Miller, C.H.; Ramirez, A.L.; Bullard, T.G.

1980-01-01

A recent and rapid increase since the mid-1970's in commercial and residential development in the Powder River Basin, Wyoming and Montana, is caused by exploitation of vast coal and other resources in the basin. One geologic hazard to such development is landsliding. A landslide sufficiently representative of others in the area was chosen for detailed seismic studies. Studies of this landslide show that a low-velocity layer overlies a high-velocity layer both on the slide and away from it and that the contact between the volocity layers is nearly parallel with the preslide topographic surface. Computed shear and other elastic moduli of the low-velocity layer are about one-tenth those of the high-velocity layer. When failure occurs within the slope materials, it will very likely be confined to the low-velocity layer. The number and position of main shear planes in the landslide are unknown, but the main slippage surface is probably near the contact between the low- and high-velocity layers. The main cause of landslide failure in the study area is apparently the addition of moisture to the low-velocity layer.

Integrated stratigraphy of Paleocene lignite seams of the fluvial Tullock Formation, Montana (USA).

NASA Astrophysics Data System (ADS)

Noorbergen, Lars J.; Kuiper, Klaudia F.; Hilgen, Frederik J.; Krijgsman, Wout; Dekkers, Mark J.; Smit, Jan; Abels, Hemmo A.

2015-04-01

Coal-bearing fluvial sedimentation is generally thought to be dominated by autogenic processes that are processes intrinsic to the sedimentary system. Ongoing research however suggests that several fluvial processes such as floodplain inundation and avulsion, can also be controlled by external forcing such as orbital climate change. Still, the exact role of orbital climate forcing in fluvial sediments is difficult to decipher since riverine deposits are complicated by variable sedimentation rates including erosion of previously deposited material, by lateral heterogeneity of sedimentation, and by scarcity of independent dating methods. The early Paleocene lignite-bearing Tullock Formation of the Williston Basin in eastern Montana represents a record of fluvial sedimentation that is perfectly exposed and, displays a seemingly regular alternation of sandstones and lignite seams. These coal beds contain multiple volcanic ash layers. Here, we use an integrated stratigraphic approach (litho- and magnetostratigraphy, geochemical fingerprinting and radio-isotope dating of volcanic ash layers) to establish a high-resolution time frame for the early Paleocene fluvial sediments. First age estimations indicate that the Tullock Formation in Eastern Montana was deposited over a time span of ~ 1000 kyr subsequent to the Cretaceous - Paleogene boundary, dated at ~ 65.95 Ma [1]. Initial high-resolution magnetostratigraphy revealed the occurrence of the C29r/C29n polarity reversal which was stratigraphic consistent at different field locations. We investigate the regional significance of sedimentary change at multiple sites of the same age in order to provide improved insight on the role of orbital forcing in fluvial coal formation. References: [1] Kuiper, K.F., Deino, A., Hilgen, F.J., Krijgsman, W., Renne, P.R., Wijbrans, J.R. (2008). Synchronizing Rock Clocks of Earth History. Science 320, 500-504.

Petrological constraints on the recycling of mafic crystal mushes, magma ascent and intrusion of braided sills in the Torres del Paine mafic complex (Patagonia)

NASA Astrophysics Data System (ADS)

Leuthold, Julien; Müntener, Othmar; Baumgartner, Lukas; Putlitz, Benita

2014-05-01

Cumulate and crystal mush disruption and reactivation are difficult to recognise in coarse grained shallow plutonic rocks. Mafic minerals included in hornblende and zoned plagioclase provide snapshots of early crystallization and cumulate formation, but are difficult to interpret in terms of the dynamics of magma ascent and possible links between silicic and mafic rock emplacement. We will present the field relations, the microtextures and the mineral chemistry of the Miocene mafic sill complex of the Torres del Paine intrusive complex (Patagonia, Chile) and its sub-vertical feeder-zone. The mafic sill complex was built up by a succession of braided sills of shoshonitic and high-K calc-alkaline porphyritic hornblende-gabbro and fine grained monzodioritic sills. The mafic units were over-accreted over 41±11 ka, underplating the overlying granite. Local diapiric structures and felsic magma accumulation between sills indicate limited separation of intercumulus liquid from the mafic sills. Anhedral hornblende cores, with olivine + clinopyroxene ± plagioclase ± apatite inclusions, crystallized at temperatures >900°C and pressures of ~300 to ~500 MPa. The corresponding rims and monzodiorite matrix crystallized at <830°C, ~70 MPa. This abrupt compositional variation suggests stability and instability of hornblende during mafic roots recycling and subsequent decompression. The near lack of intercumulus crystals in the sub-vertical feeder zone layered gabbronorite and pyroxene-hornblende gabbronorite stocks testifies that melt is more efficiently extracted than in sills, resulting in a cumulate signature in the feeding system. The emplacement age of the sill complex topmost granitic unit is identical, within uncertainties, to the feeder zone mafic cumulates. Granitic liquids formed by AFC processes and were extracted at high temperature (T>950°C) from the middle crust reservoir to the emplacement level. We show that hornblende-plagioclase thermobarometry is a useful monitor for the determination of segregation conditions of granitic magmas from gabbroic crystal mushes, and for monitoring the evolution of shallow crustal magmatic crystallization, decompression and cooling.

Catalytic hydrotreating process

DOEpatents

Karr, Jr., Clarence; McCaskill, Kenneth B.

1978-01-01

Carbonaceous liquids boiling above about 300.degree. C such as tars, petroleum residuals, shale oils and coal-derived liquids are catalytically hydrotreated by introducing the carbonaceous liquid into a reaction zone at a temperature in the range of 300.degree. to 450.degree. C and a pressure in the range of 300 to 4000 psig for effecting contact between the carbonaceous liquid and a catalytic transition metal sulfide in the reaction zone as a layer on a hydrogen permeable transition metal substrate and then introducing hydrogen into the reaction zone by diffusing the hydrogen through the substrate to effect the hydrogenation of the carbonaceous liquid in the presence of the catalytic sulfide layer.

[Contamination Assessment and Sources Analysis of Soil Heavy Metals in Opencast Mine of East Junggar Basin in Xinjiang].

PubMed

Liu, Wei; Yang, Jian-jun; Wang, Jun; Wang, Guo; Cao, Yue-e

2016-05-15

The opencast mine of East Junggar Basin in Xinjiang is the largest self-contained coalfield in China, and the ecological environment of the opencast is very fragile because of its arid climate and poor soil. In this study, 50 soil samples (from 0 to 30 cm depth soil at intervals of 10 cm) in opencast Mine of East Junggar Basin in Xinjiang were collected in order to explore the heavy metals contamination of the coal mining. The contents of zinc (Zn), copper (Cu), cadmium (Cr), lead (Pb), mercury (Hg) and arsenic (As) were measured and the degree of pollution was assessed by Nemerow index, geo-accumulation (Igeo) index and potential ecological risk index. In addition, the layered comparison, dust fall and the distance between coal mine and samples location were used to analyze the source of heavy metals contamination. The results showed that value of As surpassed the Chinese soil quality standard class I (GB 15618-1995) mostly severely, followed by Cr, a relatively lower surpass was obtained by Hg and Cu, while Zn and Pb did not surpass the standard. According to the standard, the soil heavy metals content of research region was in light pollution status and the pollution index for each heavy metal followed the order of As (2.07) > Cr (0.95) > Cu (0.55) > Zn (0.48) > Hg (0.45) > Pb (0.38), which demonstrated a heavy pollution of As and clean status of others. Additionally, an Igeo value of 1.14 for Hg reflected a moderated pollution. The major contribution factor was Hg with a risk index of 251.40. The source analysis showed that the content of Pb in the surface soil (10-20 cm) was different from that in the deep layer (20-30 cm), which may be caused by coal combustion and other human activities. The sources of Hg and As were similar and may come from coal combustion. The distance to the mining area was not the major factor affecting the diffusion of heavy metals, other candidate factors included terrain, aspect and wind direction, etc.

Stratigraphy and structure of coalbed methane reservoirs in the United States: an overview

USGS Publications Warehouse

Pashin, J.C.

1998-01-01

Stratigraphy and geologic structure determine the shape, continuity and permeability of coal and are therefore critical considerations for designing exploration and production strategies for coalbed methane. Coal in the United states is dominantly of Pennsylvanian, Cretaceous and Tertiary age, and to date, more than 90% of the coalbed methane produced is from Pennsylvanian and cretaceous strata of the Black Warrior and San Juan Basins. Investigations of these basins establish that sequence stratigraphy is a promising approach for regional characterization of coalbed methane reservoirs. Local stratigraphic variation within these strata is the product of sedimentologic and tectonic processes and is a consideration for selecting completion zones. Coalbed methane production in the United States is mainly from foreland and intermontane basins containing diverse compression and extensional structures. Balanced structural models can be used to construct and validate cross sections as well as to quantify layer-parallel strain and predict the distribution of fractures. Folds and faults influence gas and water production in diverse ways. However, interwell heterogeneity related to fractures and shear structures makes the performance of individual wells difficult to predict.Stratigraphy and geologic structure determine the shape, continuity and permeability of coal and are therefore critical considerations for designing exploration and production strategies for coalbed methane. Coal in the United States is dominantly of Pennsylvanian, Cretaceous and Tertiary age, and to date, more than 90% of the coalbed methane produced is from Pennsylvanian and Cretaceous strata of the Black Warrior and San Juan Basins. Investigations of these basins establish that sequence stratigraphy is a promising approach for regional characterization of coalbed methane reservoirs. Local stratigraphic variation within these strata is the product of sedimentologic and tectonic processes and is a consideration for selecting completion zones. Coalbed methane production in the United States is mainly from foreland and intermontane basins containing diverse compressional and extensional structures. Balanced structural models can be used to construct and validate cross sections as well as to quantify layer-parallel strain and predict the distribution of fractures. Folds and faults influence gas and water production in diverse ways. However, interwell heterogeneity related to fractures and shear structures makes the performance of individual wells difficult to predict.

Catalyst support structure, catalyst including the structure, reactor including a catalyst, and methods of forming same

DOEpatents

Van Norman, Staci A.; Aston, Victoria J.; Weimer, Alan W.

2017-05-09

Structures, catalysts, and reactors suitable for use for a variety of applications, including gas-to-liquid and coal-to-liquid processes and methods of forming the structures, catalysts, and reactors are disclosed. The catalyst material can be deposited onto an inner wall of a microtubular reactor and/or onto porous tungsten support structures using atomic layer deposition techniques.

JPRS report: Science and technology. Central Eurasia

NASA Astrophysics Data System (ADS)

1995-02-01

Translated articles cover the following topics: laser-controlled rotary microwave waveguide junction; optical pulse-phase modulation of semiconductor laser; amplitude-phase distortions of light beam obliquely propagating through ground layer of troposphere; antenna arrays with ultrafast beam scanning; materials for a walk on moon; textile-wood-coal briquette path to capitalism; and development of automated system for scientific research and design of heat and mass transfer processes.

Electron-probe microanalysis of light elements in coal and other kerogen

USGS Publications Warehouse

Bustin, R.M.; Mastalerz, Maria; Raudsepp, M.

1996-01-01

Recent advances in electron microprobe technology including development of layered synthetic microstructures, more stable electronics and better matrix-correction programs facilitated routine microanalysis of the light elements in coal. Utilizing an appropriately equipped electron microprobe with suitable standards, it is now possible to analyze directly the light elements (C, O and N, if abundant) in coal macerals and other kerogen. The analytical results are both accurate compared to ASTM methods and highly precise, and provide an opportunity to access the variation in coal chemistry at the micrometre scale. Our experiments show that analyses using a 10 kV accelerating voltage and 10 nA beam current yield the most reliable data and result in minimum sample damage and contamination. High sample counts were obtained for C, O and N using a bi-elemental nickel-carbon pseudo-crystal (2d = 9.5 nm) as an analyzing crystal. Vitrinite isolated from anthracite rank coal proves the best carbon standard and is more desirable than graphite which has higher porosity, whereas lower rank vitrinite is too heterogeneous to use routinely as a standard. Other standards utilized were magnesite for oxygen and BN for nitrogen. No significant carbon, oxygen or nitrogen X-ray peak shifts or peak-shape changes occur between standards and the kerogen analyzed. Counting rates for carbon and oxygen were found to be constant over a range of beam sizes and currents for counting times up to 160 s. Probe-determined carbon and oxygen contents agree closely with those reported from ASTM analyses. Nitrogen analyses compare poorly to ASTM values which probably is in response to overlap between the nitrogen Ka peak with the carbon K-adsorption edge and the overall low nitrogen content of most of our samples. Our results show that the electron microprobe technique provides accurate compositional data for both minor and major elements in coal without the necessity and inherent problems associated with mechanically isolating macerals. Studies to date have demonstrated the level of compositional variability within and between macerals in suites of Canadian coals.

Prediction of Compressional Wave Velocity Using Regression and Neural Network Modeling and Estimation of Stress Orientation in Bokaro Coalfield, India

NASA Astrophysics Data System (ADS)

Paul, Suman; Ali, Muhammad; Chatterjee, Rima

2018-01-01

Velocity of compressional wave ( V P) of coal and non-coal lithology is predicted from five wells from the Bokaro coalfield (CF), India. Shear sonic travel time logs are not recorded for all wells under the study area. Shear wave velocity ( Vs) is available only for two wells: one from east and other from west Bokaro CF. The major lithologies of this CF are dominated by coal, shaly coal of Barakar formation. This paper focuses on the (a) relationship between Vp and Vs, (b) prediction of Vp using regression and neural network modeling and (c) estimation of maximum horizontal stress from image log. Coal characterizes with low acoustic impedance (AI) as compared to the overlying and underlying strata. The cross-plot between AI and Vp/ Vs is able to identify coal, shaly coal, shale and sandstone from wells in Bokaro CF. The relationship between Vp and Vs is obtained with excellent goodness of fit ( R 2) ranging from 0.90 to 0.93. Linear multiple regression and multi-layered feed-forward neural network (MLFN) models are developed for prediction Vp from two wells using four input log parameters: gamma ray, resistivity, bulk density and neutron porosity. Regression model predicted Vp shows poor fit (from R 2 = 0.28) to good fit ( R 2 = 0.79) with the observed velocity. MLFN model predicted Vp indicates satisfactory to good R2 values varying from 0.62 to 0.92 with the observed velocity. Maximum horizontal stress orientation from a well at west Bokaro CF is studied from Formation Micro-Imager (FMI) log. Breakouts and drilling-induced fractures (DIFs) are identified from the FMI log. Breakout length of 4.5 m is oriented towards N60°W whereas the orientation of DIFs for a cumulative length of 26.5 m is varying from N15°E to N35°E. The mean maximum horizontal stress in this CF is towards N28°E.

Relationships among macerals, minerals, miospores and paleoecology in a column of Redstone coal (Upper Pennsylvanian) from north-central West Virginia (U.S.A.)

USGS Publications Warehouse

Grady, W.C.; Eble, C.F.

1990-01-01

Two distinct paleoenvironments are represented in vertical succession in a column of Redstone coal in north-central West Virginia as indicated by a study of 37 consecutive 3-cm (0.1 ft) increments analyzed for ash yield, petrographic composition, low-temperature ash mineralogy and palynomorph abundances. Abundance profiles were constructed for ash, 12 petrographic components, 3 minerals and 5 miospore assemblages. The profiles and calculated correlation coefficients show close relationships between several constituents. Components that increased in abundance upward in the coal bed were a collinite type > 50 microns in thickness, cutinite, and miospores affiliated with calamites, herbaceous lycopods, cordaites and herbaceous ferns. Components that decreased in abundance upward were a collinite type 50 ??m in thickness, cutinite, calamite and cordaite miospores and kaolinite. Significant correlations occurred between ash yield and the collinite types > 50 and < 50 ??m in thickness but no significant correlation was found between ash yield and total vitrinite-group content. This is interpreted to show that division of vitrinite macerals by size is important in petrographic paleoenvironmental studies. Paleoecologic interpretations based upon these correlations suggest that two distinct, planar, probably topogenous paleoecologic environments are represented in this column of the Redstone coal. The lower two-thirds of the coal bed was interpreted to have accumulated in a planar swamp in which significant introduction of detrital or dissolved mineral matter, and significant anaerobic and moderate oxidative degradation of the peat occurred. The flora of this paleoenvironment was dominated by tree ferns. The paleoenvironment during accumulation of the upper one-third of the coal bed was also interpreted to have been a planar swamp, but one in which moderate to low introduction of detrital or dissolved mineral matter, and minor anaerobic and oxidative degradation of the peat occurred. The dominant flora of this paleoenvironment consisted mainly of calamites with fewer cordaites and herbaceous ferns. This study shows that valuable paleoecologic information may be obtained by sampling closely spaced vertical increments. No mixing of detrital sediments with the peat was observed in coal layers immediately adjacent to the parting or the overlying sandstone unit. ?? 1990.

Investigating waste rock, tailings, slag and coal ash clinker as adsorbents for heavy metals: Batch and column studies

NASA Astrophysics Data System (ADS)

Letina, D.; Letshwenyo, W. M.

2018-06-01

Wastewater from the mining industry is a concern because most of the time it contains heavy metals with concentrations above permissible levels, posing a threat to terrestrial and aquatic life. The study was conducted to evaluate the effectiveness of locally available waste materials (waste rock, tailings, coal ash clinker, and slag) generated by BCL (Ltd) mine, a copper and nickel mining and smelting company in Botswana, for removal of nickel and copper from the real mining wastewater. Batch adsorption studies were conducted to establish the adsorptive efficiency and kinetics of each media with respect to nickel and copper ions. The best media was further evaluated through fixed bed column studies at 24 and 48 h empty bed contact time. The results indicate that the percentage removal for coal ash clinker, waste rock, smelter slag and tailings was 98%, 15%, 3% and -3% with respect to copper ions, and 46%, 9%, 7% and 2% with respect to nickel ions for each media respectively. Coal ash clinker followed pseudo first order kinetic model and Langmuir isotherm model with respect to nickel ions indicating the dominance of physisorption and mono layer coverage respectively. The Langmuir separation factor (RL) was 0.37 suggesting favourable adsorption onto the media. Fixed bed column studies revealed that copper was completely retained in the bed at both 24 and 48 h contact times. In the case of nickel, removal efficiency ranged between 83% and 99% when contact time was 48 h and between 68% and 99% when the contact time was reduced to 24 h. Breakthrough was not reached after 19 bed volumes. It can be concluded that coal ash clinker is a better candidate for the removal of copper and nickel ions from mining wastewater.

Remediation of Coal Tar by STAR: Self-Sustaining Propagation Across Clean Gaps

NASA Astrophysics Data System (ADS)

Gerhard, J.; Brown, J.; Torero, J. L.; Grant, G.

2016-12-01

Self-sustaining Treatment for Active Remediation (STAR) is an emerging remediation technique which utilizes a subsurface smouldering reaction to destroy non-aqueous phase liquids (NAPL) in situ. The reaction is self-sustaining in that, once ignited, the destructive smouldering front will propagate outwards using only the energy embedded in the contaminant. However, it is known that coal tar can occur as both a continuous pool as well as in distinct seams separated by clean intervals. This study evaluated the hypothesis that the smouldering reaction can cross or `jump' clean gaps by transferring enough heat through the gap to re-ignite the reaction in the contaminated region beyond. Column and 2D box experiments were performed at two scales to determine the maximum clean gap which could be jumped vertically and horizontally. Once the maximum gap had been determined, sensitivity to various in situ and engineering control parameters were explored including: coal tar layer thickness, soil permeability, moisture content, NAPL saturation, and air injection flowrate. High resolution thermocouples informed the progress of the reaction, continuous gas emissions analysis revealed when the reaction was active and dormant, and detailed excavation mapped the extent of remediation and whether gaps were successfully jumped. The work demonstrated that substantial clean gaps, approaching the limit of the laboratory scale, can be jumped by the smouldering reaction using convective heat transfer. Also observed in some cases was the mobilization of pre-heated coal tar into the clean gaps and the reaction's ability to propagate through and destroy coal tar both adjacent to and within the gaps. This work is providing new insights into the robust nature of the technology for in situ applications, and indicating how extreme the heterogeneity has to be before the reaction is interrupted and a new ignition location would be required.

Hydrogeology and simulation of groundwater flow at the Green Valley reclaimed coal refuse site near Terre Haute, Indiana

USGS Publications Warehouse

Bayless, E. Randall; Arihood, Leslie D.; Fowler, Kathleen K.

2011-01-01

The Green Valley reclaimed coal refuse site, near Terre Haute, Ind., was mined for coal from 1948 to 1963. Subsurface coal was cleaned and sorted at land surface, and waste material was deposited over the native glacial till. Approximately 2.7 million cubic yards of waste was deposited over 159 acres (92.3 hectares) in tailings ponds and gob piles. During 1993, the Indiana Department of Natural Resources, Division of Reclamation, improved the site by grading gob piles, filling tailings ponds, and covering the refuse with a layer of glacial drift. During 2008, the Division of Reclamation and U.S. Geological Survey initiated a cooperative investigation to characterize the hydrogeology of the site and construct a calibrated groundwater flow model that could be used to simulate the results of future remedial actions. In support of the modeling, a data-collection network was installed at the Green Valley site to measure weather components, geophysical properties, groundwater levels, and stream and seep flow. Results of the investigation indicate that (1) there is negligible overland flow from the site, (2) the prevailing groundwater-flow direction is from northeast to southwest, with a much smaller drainage to the northeast, (3) there is not a direct hydraulic connection between the refuse and West Little Sugar Creek, (4) about 24 percent of the groundwater recharge emerges through seeps, and water from the seeps evaporates or eventually flows to West Little Sugar Creek and the Green Valley Mine Pond, and (5) about 72 percent of groundwater recharge moves vertically downward from the coal refuse into the till and follows long, slow flow paths to eventual dischage points.

Fine particles flotation of the Moatize coal/Mozambique

NASA Astrophysics Data System (ADS)

Castro, Amilton; de Brum, Irineu A. S.

2017-11-01

This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the UCB layer. Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were Betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of Betacol concentrations in the first test phase was 200 g / t at 500 g / t, and in the second phase 200 g / t at 500 g / t of diesel oil and MIBC were kept constant at 300 g / t. The immediate analysis followed the Brazilian standards: NBR 8289, NBR 8293, NBR 8290, NBR 8299. The results showed that it is possible, from a feed with the ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of Betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.

An example of applied structural petrology in the Illinois Basin: Sphalerite kaolinite and their relation to the depth and relative timing of coal jointing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ambers, C.P.

1993-03-01

Sphalerite is associated with very well crystallized kaolinite (VWCK) in geodes, siderite nodules and coal cleats in the Illinois Basin and allows estimation of the temperature of formation of the VWCK using fluid inclusions. The approximate depth of kaolinite growth and the relative timing of coal fracturing can then be ascertained. Sphalerite associated with VWCK was extracted from Mississippian geodes collected near Keokuk, Iowa, and from Pennsylvanian siderite nodules and coal collected in SW Indiana. Inclusions in the sphalerite consist of VWCK; large, negative crystal, two-phase fluid inclusions; small, fracture-related, two-phase fluid inclusions; and organic inclusions. Homogenization temperatures of 89more » C [+-] 10, 115 C [+-] 15, 89 C [+-] 5 were measured for the two-phase inclusions in sphalerite from the geodes, siderite nodules and coal, respectively. Freezing temperatures of the inclusions in the geode and siderite nodule sphalerite were measured at [minus]13.5 C [+-] 0.5 and [minus]9.4 C [+-] 0.2, indicating moderate salinity. Using a geothermal gradient range of 23--36 C/km and an average surface temperature of 20 C, kaolinite and sphalerite probably grew at depths of about 1.9 to 4.1 km. In SW Indiana, VWCK occurs in vertical, non-penetrative joints in vitrinite layers. Penetrative joint sets rarely contain VWCK. At nearly all of the 28 sites studied, two sets of barren cleats occur oriented N10W to NSE and N80E to N95E. The orientation of barren, penetrative cleats shows that the maximum horizontal stress rotated CW from the earlier stress field. Rare VWCK in the late cleats suggests they also formed at depth after the thermal maxima.« less

Phytoremediation of spoil coal dumps in Western Donbass (Ukraine)

NASA Astrophysics Data System (ADS)

Klimkina, Iryna; Kharytonov, Mykola; Wiche, Oliver; Heilmeier, Hermann

2017-04-01

At the moment, in Ukraine about 150 thousand hectares of fertile land are occupied by spoil dumps. Moreover, this figure increases every year. According to the technology used about 1500 m3 of adjacent stratum is dumped at the surface per every 1000 tons of coal mined. Apart from land amortization, waste dumps drastically change the natural landscape and pollute air, soil and water sources as the result of water and wind erosion, as well as self-ignition processes. A serious concern exists with respect to the Western Donbass coal mining region in Ukraine, where the coal extraction is made by the subsurface way and solid wastes are represented by both spoil dumps and wastes after coal processing. Sulphides, mostly pyrite (up to 4% of waste material), are widely distributed in the waste heaps freshly removed due to coal mining in Western Donbass.The oxidation of pyrite with the presence of oxygen and water is accompanied by a sharp drop in the pH from the surface layer to the spoil dumps(from 5.2-6.2 to 3.9-4.2 in soil substrates with chernozen and from 8.3-8.4 to 6.7-7.2 in soil substrates with red-brown clay, stabilizing in dump material in both cases at 2.9-3.2). Low pH generates the transformation of a number of toxic metals and other elementspresent in waste rock (e.g. Fe, Al, Mn, Zn, Mo, Co, As, Cd, Bi, Pb, U) into mobile forms. To stabilize and reduce metal mobility the most resistant plants that occur naturally in specified ecosystems can be used. On coal spoil dumpsin Western Donbas the dominant species are Bromopsis inermis, subdominant Artemisia austriaca; widespread are also Festucas pp., Lathyrus tuberosus, Inula sp., Calamagrostis epigeios, Lotus ucrainicus, and Vicias pp. Identification of plants tolerant to target metals is a key issue in phytotechnology for soil restoration. It is hypothesized that naturally occurring plants growing on coal spoil dumps can be candidates for phytostabilization, phytoextraction (phytoaccumulation) and phytomining techniques. Results on accumulation of target elements in the above- and below ground biomass of abundant plant species will be used to discuss their phytoremediation potential for spoil coal dumps in Western Donbas. Research is being carried out in the framework of DAAD project "Biotechnology in Mining - Integration of New Technologies into Educational Practice" and cooperation between TechnischeUniversität Bergakademie Freiberg, Germany, and National Mining University, Dnipro, Ukraine.

Properties, origin and nomenclature of rodlets of the inertinite maceral group in coals of the central Appalachian basin, U.S.A.

USGS Publications Warehouse

Lyons, P.C.; Finkelman, R.B.; Thompson, C.L.; Brown, F.W.; Hatcher, P.G.

1982-01-01

Resin rodlets, sclerenchyma strands and woody splinters, which are collectively called rodlets, were studied by chemical, optical petrographic, and scanning-electron microscopic (SEM) techniques. A study was made of such rodlets from the bituminous coal beds of the central Appalachian basin (Pennsylvanian; Upper Carboniferous) of the United States. Comparisons were made with rodlets from coal beds of the Illinois basin, the Southern Anthracite Field of Pennsylvania, the St. Rose coal field of Nova Scotia, and European and other coal fields. In order to determine their physical and chemical properties, a detailed study was made of the rodlets from the Pomeroy coal bed (high volatile A bituminous coal; Monongahela Formation; Upper Pennsylvanian) of Kanawha County, West Virginia. The origin of the rodlets was determined by a comparative analysis of a medullosan (seed fern) stem from the Herrin (No. 6) coal bed (high volatile C bituminous coal; Carbondale Formation) from Washington County, Illinois. Rodlets are commonly concentrated in fusain or carbominerite layers or lenses in bituminous coal beds of the central Appalachian basin. Most of the rodlets examined in our study were probably derived from medullosan seed ferns. The three types of rodlets are distinguished on the basis of cellularity, morphology and fracture. The resin rodlets studied by us are noncellular and appear to be similar in properties and origin to those found in coal beds of the Middle and Upper Pennsylvanian of the Illinois basin. The resin rodlets extracted from the Pomeroy coal bed exhibit high relief and high reflectance when polished and viewed in reflected light; they are opaque in transmitted light. In cross section, the resin rodlets are oval to round and have diameters ranging from 60 to 450 ??m. Many are solid, but some have vesicles, canals or cavities, which are commonly filled with clay, probably kaolinite. Typically, they have distinct fracture patterns ("kerfs") in longitudinal and cross sections and many are characterized by dense (probably oxidized) rims. The orientation and amounts of void space and mineralization of resin rodlets in coal have resulted in much confusion in their recognition and classification. The resin rodlets are petrographically recognized as sclerotinites of the inertinite maceral group. We here propose that resin rodlets be assigned to the maceral variety of sclerotinites termed "resino-sclerotinite" because of their presumable resinous origin. Other investigators have confused some fusinitized resin rodlets with fungal masses, which have different morphological properties and which probably have different chemical properties. We here propose that such fungal masses be assigned to the maceral variety of sclerotinites termed "fungo-sclerotinite.". The sclerenchyma strands examined in our study are cellular, thick-walled, and crescent-shaped in cross section. They exhibit high reflectance and high relief and belong to semifusinite and fusinite of the inertinite maceral group. Sclerenchyma strands are commonly associated with resin canals in Medullosa and related seed-fern genera, which are common in coal balls of the Illinois basin. We here propose adoption of the maceral varietal terms "sclerenchymo-fusinite" and "sclerenchymo-semifusinite" for these bodies. The woody splinters in the Pomeroy coal bed are cellular and thin-walled and have scattered pits as much as a few microns in diameter. They are dark brown to black in transmitted light and commonly have a lower reflectance than the resino-sclerotinite and sclerenchymo-fusinite of the Pomeroy coal. The woody splinters belong to semifusinite and fusinite of the inertinite maceral group. The maceral varietal terms "xylemo-semifusinite" and "xylemo-fusinite" are here proposed for these bodies. Elemental chemical data for the resin rodlets of the Pomeroy coal bed of the central Appalachian basin indicate that resin rodlets have significantly lower atomic H/C and O/C ratio

Observations on the palynology, petrography and geochemistry of the Western Kentucky number 4 coal bed

USGS Publications Warehouse

Eble, C.F.; Greb, S.F.; Williams, D.A.; Hower, J.C.

1999-01-01

Eight bench-column samples of the Western Kentucky Number 4 coal bed, collected from an area along the southern margin of the Western Kentucky Coal Field, were analyzed palynologically, petrographically, and geochemically to document both temporal and spatial variability among these parameters. The Western Kentucky Number 4 coal occurs near the top of the Tradewater Formation, is of Early Desmoinesian age, and is correlative with the lower part of the Allegheny Formation of the Appalachian Basin, and Late Bolsovian strata of western Europe. Palynologically, the coal is co-dominated by spores that were produced by lycopod trees (Lycospora and Granasporites medius) and tree ferns. Thin-walled tree fern spores (Punctatisporites minutus, P. minutus, P. rotundus) are more abundant than thick-walled forms (Laevigatosporites globosus, P. granifer). Calamitean spores (Calamospora and Laevigatosporites spp.) are locally abundant as is cordaitean pollen (Florinites). Small fern (Granulatisporites) and small lycopod spores (Densosporites, Cirratriradites, Endosporites and Anacanthotriletes spinosus) are present, but occur in minor amounts. Temporal changes in palynomorph composition occur, but are not uniform between columns. Spatial variability among columns is also evident. Petrographically, the coal is dominated by vitrinite macerals, with telinite and telocollinite generally occurring more commonly than desmocollinite and gelocollinite. Basal benches typically contain high percentages of vitrinite; middle benches usually contain higher percentages of liptinite and inertinite. In about half the studied columns, the terminal coal benches show a slight increase in vitrinite. In the study area, the petrography of the Western Kentucky Number 4 coal is more uniform than the palynology. Ash yields and total sulfur contents are temporally uniform in some columns, but variable in others. In the latter case, higher percentages of ash and sulfur occur at the base of the bed and decrease up to the middle of the bed. The terminal benches of these columns often, but not always, show slight increases in ash or sulfur. Both syngenetic and epigenetic forms of sulfur are present in the Western Kentucky Number 4 coal. The high vitrinite contents and moderate to high sulfur contents suggest that the Western Kentucky Number 4 paleomire was mainly planar and rheotrophic throughout its developmental history. Groundwaters carrying dissolved solutes may have helped neutralize the normally acidic interstitial peat waters allowing for the production of sulfide minerals. Several of the columns with high sulfur contents at the base of the bed occur in faulted areas. The faults could have promoted the flow of groundwaters through the peat, providing an increased dissolved load for acid mitigation and sulfide formation. The concentration of sulfur at the base of the bed may be a function of the peat/underclay contact enhancing sulfide formation. The clay layer may also have acted as an impermeable boundary for downward moving groundwaters, causing mainly lateral, rather than vertical movement along the base of the coal bed.Eight bench-column samples of the Western Kentucky Number 4 coal bed were analyzed palynologically, petrographically, and geochemically to study both temporal and spatial variability among these parameters. Palynologically, the coal is co-dominated by spores that were produced by lycopod trees and tree ferns. Petrographically, the coal is dominated by vitrinite macerals, with telinite and telocollinite generally occurring more commonly than desmocollinite and gelocollinite. The petrography of the coal was found to be more uniform than the palynology.

Learning about Teachers through Film.

ERIC Educational Resources Information Center

Raimo, Angela; Devlin-Scherer, Roberta; Zinicola, Debra

2002-01-01

Analysis of films featuring teachers reveals a variety of roles portrayed: teacher as culture guardian, iconoclast/subverter, alien culture-bearer, change agent, learner, compassionate mentor, student advocate, maverick, and incompetent. Examination of these portrayals can prompt critical thinking about teacher responses to different social and…

Queering Outdoor Education.

ERIC Educational Resources Information Center

Russell, Connie; Sarick, Tema; Kennelly, Jackie

2003-01-01

Queer pedagogy is rife with possibilities for outdoor educators to challenge the status quo of heterosexism and sexism. From recognizing and addressing the heteronormative assumptions that influence the outdoor classroom, to subverting oppressive gender norms, to noticing the cultural constructs through which we view nature, queer pedagogy can…

Career Education--The Final Impoverishment of Learning?

ERIC Educational Resources Information Center

Nash, Robert J.; Agne, Russell M.

1973-01-01

Career educators appear to be developing an approach to schooling rooted in at least four questionable assumptions about the learning process. Unless these interrelated assumptions are critically examined and rectified, then the most beneficial intended outcomes of career education will be subverted. (Authors)

Women's Struggle against Tradition in Bangladesh.

ERIC Educational Resources Information Center

Sultan, Mainus

1994-01-01

In rural Bangladesh, women's participation in a literacy program was opposed by Mullahs for several reasons: content encouraged decision making, monopoly of the Qur'anic schools was threatened, Mullahs' leadership and spiritual roles were potentially subverted, and it conflicted with the practice of polygamy. (SK)

Combining linear polarization spectroscopy and the Representative Layer Theory to measure the Beer-Lambert law absorbance of highly scattering materials.

PubMed

Gobrecht, Alexia; Bendoula, Ryad; Roger, Jean-Michel; Bellon-Maurel, Véronique

2015-01-01

Visible and Near Infrared (Vis-NIR) Spectroscopy is a powerful non destructive analytical method used to analyze major compounds in bulk materials and products and requiring no sample preparation. It is widely used in routine analysis and also in-line in industries, in-vivo with biomedical applications or in-field for agricultural and environmental applications. However, highly scattering samples subvert Beer-Lambert law's linear relationship between spectral absorbance and the concentrations. Instead of spectral pre-processing, which is commonly used by Vis-NIR spectroscopists to mitigate the scattering effect, we put forward an optical method, based on Polarized Light Spectroscopy to improve the absorbance signal measurement on highly scattering samples. This method selects part of the signal which is less impacted by scattering. The resulted signal is combined in the Absorption/Remission function defined in Dahm's Representative Layer Theory to compute an absorbance signal fulfilling Beer-Lambert's law, i.e. being linearly related to concentration of the chemicals composing the sample. The underpinning theories have been experimentally evaluated on scattering samples in liquid form and in powdered form. The method produced more accurate spectra and the Pearson's coefficient assessing the linearity between the absorbance spectra and the concentration of the added dye improved from 0.94 to 0.99 for liquid samples and 0.84-0.97 for powdered samples. Copyright © 2014 Elsevier B.V. All rights reserved.

Surface morphology of active normal faults in hard rock: Implications for the mechanics of the Asal Rift, Djibouti

NASA Astrophysics Data System (ADS)

Pinzuti, Paul; Mignan, Arnaud; King, Geoffrey C. P.

2010-10-01

Tectonic-stretching models have been previously proposed to explain the process of continental break-up through the example of the Asal Rift, Djibouti, one of the few places where the early stages of seafloor spreading can be observed. In these models, deformation is distributed starting at the base of a shallow seismogenic zone, in which sub-vertical normal faults are responsible for subsidence whereas cracks accommodate extension. Alternative models suggest that extension results from localised magma intrusion, with normal faults accommodating extension and subsidence only above the maximum reach of the magma column. In these magmatic rifting models, or so-called magmatic intrusion models, normal faults have dips of 45-55° and root into dikes. Vertical profiles of normal fault scarps from levelling campaign in the Asal Rift, where normal faults seem sub-vertical at surface level, have been analysed to discuss the creation and evolution of normal faults in massive fractured rocks (basalt lava flows), using mechanical and kinematics concepts. We show that the studied normal fault planes actually have an average dip ranging between 45° and 65° and are characterised by an irregular stepped form. We suggest that these normal fault scarps correspond to sub-vertical en echelon structures, and that, at greater depth, these scarps combine and give birth to dipping normal faults. The results of our analysis are compatible with the magmatic intrusion models instead of tectonic-stretching models. The geometry of faulting between the Fieale volcano and Lake Asal in the Asal Rift can be simply related to the depth of diking, which in turn can be related to magma supply. This new view supports the magmatic intrusion model of early stages of continental breaking.

Salmonella employs multiple mechanisms to subvert the TLR-inducible zinc-mediated antimicrobial response of human macrophages.

PubMed

Kapetanovic, Ronan; Bokil, Nilesh J; Achard, Maud E S; Ong, Cheryl-Lynn Y; Peters, Kate M; Stocks, Claudia J; Phan, Minh-Duy; Monteleone, Mercedes; Schroder, Kate; Irvine, Katharine M; Saunders, Bernadette M; Walker, Mark J; Stacey, Katryn J; McEwan, Alastair G; Schembri, Mark A; Sweet, Matthew J

2016-05-01

We aimed to characterize antimicrobial zinc trafficking within macrophages and to determine whether the professional intramacrophage pathogen Salmonella enterica serovar Typhimurium (S Typhimurium) subverts this pathway. Using both Escherichia coli and S Typhimurium, we show that TLR signaling promotes the accumulation of vesicular zinc within primary human macrophages. Vesicular zinc is delivered to E. coli to promote microbial clearance, whereas S. Typhimurium evades this response via Salmonella pathogenicity island (SPI)-1. Even in the absence of SPI-1 and the zinc exporter ZntA, S Typhimurium resists the innate immune zinc stress response, implying the existence of additional host subversion mechanisms. We also demonstrate the combinatorial antimicrobial effects of zinc and copper, a pathway that S. Typhimurium again evades. Our use of complementary tools and approaches, including confocal microscopy, direct assessment of intramacrophage bacterial zinc stress responses, specific E. coli and S Typhimurium mutants, and inductively coupled plasma mass spectroscopy, has enabled carefully controlled characterization of this novel innate immune antimicrobial pathway. In summary, our study provides new insights at the cellular level into the well-documented effects of zinc in promoting host defense against infectious disease, as well as the complex host subversion strategies employed by S Typhimurium to combat this pathway.-Kapetanovic, R., Bokil, N. J., Achard, M. E. S., Ong, C.-L. Y., Peters, K. M., Stocks, C. J., Phan, M.-D., Monteleone, M., Schroder, K., Irvine, K. M., Saunders, B. M., Walker, M. J., Stacey, K. J., McEwan, A. G., Schembri, M. A., Sweet, M. J. Salmonella employs multiple mechanisms to subvert the TLR-inducible zinc-mediated antimicrobial response of human macrophages. © FASEB.

Intact Pneumococci Trigger Transcription of Interferon-Related Genes in Human Monocytes, while Fragmented, Autolyzed Bacteria Subvert This Response

PubMed Central

Nordén, Rickard; Martner, Anna; Samuelsson, Ebba; Hynsjö, Lars; Wold, Agnes E.

2017-01-01

ABSTRACT A peculiar trait of pneumococci (Streptococcus pneumoniae) is their propensity to undergo spontaneous lysis during stationary growth due to activation of the enzyme autolysin (LytA), which fragments the peptidoglycan cell wall. The fragments that are generated upon autolysis impair phagocytosis and reduce production of interleukin-12 (IL-12) and gamma interferon (IFN-γ) by human leukocytes in response to intact pneumococci, thereby impeding crucial host defenses. The objective was to identify additional monocyte genes whose transcription is induced by intact pneumococci and subverted by autolyzed bacteria. Monocytes were isolated from healthy blood donors and stimulated for 3 h with UV-inactivated S. pneumoniae (Rx1PLY− LytA+ strain), which is capable of autolyzing, its LytA− isogenic autolysin-deficient mutant, or a mixture of the two (containing twice the initial bacterial concentration). Gene expression was assessed by Illumina microarray, and selected findings were confirmed by reverse transcription-quantitative real-time PCR (RT-qPCR), enzyme-linked immunosorbent assay (ELISA), and flow cytometry. In all, we identified 121 genes that were upregulated to a significantly higher degree by intact than autolyzed pneumococci. These included IFNB1 and a large set of interferon-induced genes, such as IFIT3, RSAD2, CFCL1, and CXCL10 genes, as well as IL12B and CD40 genes. RT-qPCR revealed that transcription of these genes in response to intact pneumococci diminished when autolyzed pneumococci were admixed and that this pattern was independent of pneumolysin. Thus, transcription of interferon-related genes is triggered by intact pneumococci and subverted by fragments generated by spontaneous bacterial autolysis. We suggest that interferon-related pathways are important for elimination of pneumococci and that autolysis contributes to virulence by extinguishing these pathways. PMID:28223347

Prediction of Floor Water Inrush: The Application of GIS-Based AHP Vulnerable Index Method to Donghuantuo Coal Mine, China

NASA Astrophysics Data System (ADS)

Wu, Qiang; Liu, Yuanzhang; Liu, Donghai; Zhou, Wanfang

2011-09-01

Floor water inrush represents a geohazard that can pose significant threat to safe operations for instance in coal mines in China and elsewhere. Its occurrence is controlled by many factors, and the processes are often not amenable to mathematical expressions. To evaluate the water inrush risk, the paper proposes the vulnerability index approach by coupling the analytic hierarchy process (AHP) and geographic information system (GIS). The detailed procedures of using this innovative approach are shown in a case study in China (Donghuantuo Coal Mine). The powerful spatial data analysis functions of GIS was used to establish the thematic layer of each of the six factors that control the water inrush, and the contribution weights of each factor was determined with the AHP method. The established AHP evaluation model was used to determine the threshold value for each risk level with a histogram of the water inrush vulnerability index. As a result, the mine area was divided into five regions with different vulnerability levels which served as general guidelines for the mine operations. The prediction results were further corroborated with the actual mining data, and the evaluation result is satisfactory.

Separation and characterization of polycyclic aromatic hydrocarbons and alkylphenols in coal derived solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hurtubise, R.J.; Allen, T.W.; Hussain, A.

1981-03-29

Dry-column chromatography with an aluminum oxide stationary phase and a n-hexane-ether (19:1) mobile phase was used to separate polycyclic aromatic hydrocarbons (PAH) by ring size. Prior to the dry-column chromatography step, the coal derived solvents were added to an acid treated silica gel column and eluted with chloroform. This step removed pyridine-type nitrogen heterocycles. After separation of the individual ring fractions, the fractions were further separated by either thin layer chromatography (TLC) or high performance liquid chromatography (HPLC). If TLC was used, then after separation fluorescence profiles of each PAH ring fraction distributed on 30%-acetylated cellulose chromatoplates were obtained withmore » a spectrodensitometer. Measurement of fluorescence peak heights gave an approximate measure of the amount of the 3-, 4-, 5-, and 6- ring PAH. For HPLC separation, the 3- and 4- ring PAH fractions obtained from the dry-column chromatography step were separated with a ..mu..-Bondapak C/sub 18/ column and methanol:water (65:35) mobile phase. The HPLC separated PAH were characterized by chromatographic correlation factors and corrected fluorescence excitation spectra. Alkylphenols were identified in coal recycle solvent sample following separation by HPLC.« less

Low cost hydrogen/novel membrane technology for hydrogen separation from synthesis gas, Phase 1. Quarterly technical progress report for the period ending March 31, 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-12-31

The goal of this program is to develop polymer membranes useful in the preparation of hydrogen from coal-derived synthesis gas. During this quarter the first experiment were aimed at developing high performance composite membranes for the separation of hydrogen from nitrogen and carbon monoxide. Three polymers have been selected as materials for these membranes: polyetherimide cellulose acetate and ethylcellulose. This quarter the investigators worked on polyetherimide and cellulose acetate membranes. The overall structure of these membranes is shown schematically in Figure 1. As shown, a microporous support membrane is first coated with a high flux intermediate layer then with anmore » ultrathin permselective layer and finally, if necessary, a thin protective high flux layer. 1 fig., 4 tabs.« less

East Europe Report, Economic and Industrial Affairs, No. 2400.

DTIC Science & Technology

1983-05-18

ducts, such as, for instance, oil, natural gas , coal, steel and cement. The socialist countries participate in large-scale successful joint programs of...which there are not many in international practice. Regarding their impact and significance, the joint construction and integration of natural gas ...separators; —reduced pollution (fallout of flue ashes and concentration of gaseous pol- lutants, particularly SO2 and N0X in ground layers of the

Characterization of Rare Earth Elements in in Clay Deposits Associated with Central Appalachian Coal Seams

NASA Astrophysics Data System (ADS)

Scott, M.; Verba, C.; Falcon, A.; Poston, J.; McKoy, M.

2017-12-01

Because of their multiple uses in clean energy technologies, rare earth elements (REE) are critical for national economic and energy security. With no current domestic source, supply remains a major concern for domestic security. Underclay - specifically the layer of stratum beneath a coal bed - is a potentially rich source of REE. This study focuses on the characterization and ion exchange recovery of REE from underclay samples from the Lower Freeport, Middle Kittanning, and Pittsburgh coal seams in West Virginia. Multimodal techniques provided quantitative assessments of REE-bearing mineral phases in select underclays and the influence of organic acid rock treatment on the recovery of REE from both exchangeable and crystalline mineral phases present. All samples are from extensively weathered horizons that contain abundant kaolinite and illite. Total REE concentrations range from 250-450 ppm and all samples have a HREE/LEEE ratio >20%. Rare earth element bearing minerals identified in the clay are monazite, xenotime, florencite, and crandallite. Our selective recovery approach is designed to isolate and recover REE through partial dissolution of the clay matrix and ion exchange rather than dissolution/recovery of phosphate or aluminosilicate bound REE. These results provide a better understanding of coal seam underclay, the affinity of REEs for specific ligands and colloids, and how the rock and ligands respond to different chemical treatments. These processes are important to the development and commercialization of efficient and cost effective methods to extract REE from domestic geologic deposits and recover into salable forms.

Deconstructive Pedagogy and Ideological Demystification in Post-Colonial Pakistan

ERIC Educational Resources Information Center

Mansoor, Asma; Malik, Samina

2016-01-01

With post-colonial Pakistan inheriting the British colonial ideological and governmental apparatus, the English literature curriculum implemented at the university level in Pakistan carried the interpellatory baggage of its colonial past. Our interdisciplinary exploration focuses on using deconstructive pedagogy to demystify and subvert the…

Changing the Poisonous Narrative

ERIC Educational Resources Information Center

Dodge, Arnold

2012-01-01

In this interview conducted by educator Arnold Dodge, education historian Diane Ravitch discusses what's wrong with the agenda of the "corporate reform movement." She notes that a current obsession with testing and a persistent blaming of teachers is subverting learning for students. The emphasis on competition, entrepreneurship, and…

Ecological Identity in Education: Subverting the Neoliberal Self

ERIC Educational Resources Information Center

Kretz, Lisa

2014-01-01

The neoliberal ideology that is hijacking educational institutions entails an atomistic, individualistic, and Western vision of self. Students are understood as competitive, economic, homogenous entities. Interpreted as information stockpiles, students collect the data necessary for the regurgitation that enables assuming their role in the…

Subverting sterols: rerouting an oxysterol-signaling pathway to promote tumor growth

PubMed Central

York, Autumn G.

2013-01-01

Oxysterols are oxidized derivatives of cholesterol that are generated enzymatically or through autoxidation. Initially identified as important lipid signaling molecules in the context of atherosclerosis and inflammation, accumulated evidence indicates that these lipid-signaling molecules can have pleiotropic effects on the fate and function of the immune system. These effects range from the regulation of immune cell survival and proliferation to chemotaxis and antiviral immunity. New studies now indicate that tumor-derived oxysterols can serve to subvert the immune system by recruiting protumorigenic neutrophils into the tumor microenvironment. The consequence of this recruitment is the generation of proangiogenic factors and matrix metalloproteinase proteins that provide a tumor a significant growth and survival advantage. In combination with other recent studies, these data highlight the ongoing cross talk between sterol metabolism and the immune system, and they raise the intriguing possibility that targeting oxysterol pathways could serve as a novel therapeutic approach in the war on cancer. PMID:23980123

NADPH oxidase-derived H2O2 subverts pathogen signaling by oxidative phosphotyrosine conversion to PB-DOPA

PubMed Central

Alvarez, Luis A.; Kovačič, Lidija; Rodríguez, Javier; Gosemann, Jan-Hendrik; Kubica, Malgorzata; Pircalabioru, Gratiela G.; Friedmacher, Florian; Cean, Ada; Ghişe, Alina; Sărăndan, Mihai B.; Puri, Prem; Daff, Simon; Plettner, Erika; von Kriegsheim, Alex; Bourke, Billy; Knaus, Ulla G.

2016-01-01

Strengthening the host immune system to fully exploit its potential as antimicrobial defense is vital in countering antibiotic resistance. Chemical compounds released during bidirectional host–pathogen cross-talk, which follows a sensing-response paradigm, can serve as protective mediators. A potent, diffusible messenger is hydrogen peroxide (H2O2), but its consequences on extracellular pathogens are unknown. Here we show that H2O2, released by the host on pathogen contact, subverts the tyrosine signaling network of a number of bacteria accustomed to low-oxygen environments. This defense mechanism uses heme-containing bacterial enzymes with peroxidase-like activity to facilitate phosphotyrosine (p-Tyr) oxidation. An intrabacterial reaction converts p-Tyr to protein-bound dopa (PB-DOPA) via a tyrosinyl radical intermediate, thereby altering antioxidant defense and inactivating enzymes involved in polysaccharide biosynthesis and metabolism. Disruption of bacterial signaling by DOPA modification reveals an infection containment strategy that weakens bacterial fitness and could be a blueprint for antivirulence approaches. PMID:27562167

Determining the seismic source mechanism and location for an explosive eruption with limited observational data: Augustine Volcano, Alaska

NASA Astrophysics Data System (ADS)

Dawson, Phillip B.; Chouet, Bernard A.; Power, John

2011-02-01

Waveform inversions of the very-long-period components of the seismic wavefield produced by an explosive eruption that occurred on 11 January, 2006 at Augustine Volcano, Alaska constrain the seismic source location to near sea level beneath the summit of the volcano. The calculated moment tensors indicate the presence of a volumetric source mechanism. Systematic reconstruction of the source mechanism shows the source consists of a sill intersected by either a sub-vertical east-west trending dike or a sub-vertical pipe and a weak single force. The trend of the dike may be controlled by the east-west trending Augustine-Seldovia arch. The data from the network of broadband sensors is limited to fourteen seismic traces, and synthetic modeling confirms the ability of the network to recover the source mechanism. The synthetic modeling also provides a guide to the expected capability of a broadband network to resolve very-long-period source mechanisms, particularly when confronted with limited observational data.

NADPH oxidase-derived H2O2 subverts pathogen signaling by oxidative phosphotyrosine conversion to PB-DOPA.

PubMed

Alvarez, Luis A; Kovačič, Lidija; Rodríguez, Javier; Gosemann, Jan-Hendrik; Kubica, Malgorzata; Pircalabioru, Gratiela G; Friedmacher, Florian; Cean, Ada; Ghişe, Alina; Sărăndan, Mihai B; Puri, Prem; Daff, Simon; Plettner, Erika; von Kriegsheim, Alex; Bourke, Billy; Knaus, Ulla G

2016-09-13

Strengthening the host immune system to fully exploit its potential as antimicrobial defense is vital in countering antibiotic resistance. Chemical compounds released during bidirectional host-pathogen cross-talk, which follows a sensing-response paradigm, can serve as protective mediators. A potent, diffusible messenger is hydrogen peroxide (H2O2), but its consequences on extracellular pathogens are unknown. Here we show that H2O2, released by the host on pathogen contact, subverts the tyrosine signaling network of a number of bacteria accustomed to low-oxygen environments. This defense mechanism uses heme-containing bacterial enzymes with peroxidase-like activity to facilitate phosphotyrosine (p-Tyr) oxidation. An intrabacterial reaction converts p-Tyr to protein-bound dopa (PB-DOPA) via a tyrosinyl radical intermediate, thereby altering antioxidant defense and inactivating enzymes involved in polysaccharide biosynthesis and metabolism. Disruption of bacterial signaling by DOPA modification reveals an infection containment strategy that weakens bacterial fitness and could be a blueprint for antivirulence approaches.

The “Visual Shock” of Francis Bacon: an essay in neuroesthetics

PubMed Central

Zeki, Semir; Ishizu, Tomohiro

2013-01-01

In this paper we discuss the work of Francis Bacon in the context of his declared aim of giving a “visual shock.”We explore what this means in terms of brain activity and what insights into the brain's visual perceptive system his work gives. We do so especially with reference to the representation of faces and bodies in the human visual brain. We discuss the evidence that shows that both these categories of stimuli have a very privileged status in visual perception, compared to the perception of other stimuli, including man-made artifacts such as houses, chairs, and cars. We show that viewing stimuli that depart significantly from a normal representation of faces and bodies entails a significant difference in the pattern of brain activation. We argue that Bacon succeeded in delivering his “visual shock” because he subverted the normal neural representation of faces and bodies, without at the same time subverting the representation of man-made artifacts. PMID:24339812

The "Visual Shock" of Francis Bacon: an essay in neuroesthetics.

PubMed

Zeki, Semir; Ishizu, Tomohiro

2013-01-01

In this paper we discuss the work of Francis Bacon in the context of his declared aim of giving a "visual shock."We explore what this means in terms of brain activity and what insights into the brain's visual perceptive system his work gives. We do so especially with reference to the representation of faces and bodies in the human visual brain. We discuss the evidence that shows that both these categories of stimuli have a very privileged status in visual perception, compared to the perception of other stimuli, including man-made artifacts such as houses, chairs, and cars. We show that viewing stimuli that depart significantly from a normal representation of faces and bodies entails a significant difference in the pattern of brain activation. We argue that Bacon succeeded in delivering his "visual shock" because he subverted the normal neural representation of faces and bodies, without at the same time subverting the representation of man-made artifacts.

Leishmania parasites: could we consider them as living organisms per se?

PubMed

Milon, Geneviève

2008-07-01

Over the last 10 years - in Microbes and Infection - the publications dealing with protozoan parasites were mainly providing insights on the pathogenic processes leading to the local or systemic damages in the mammals, these parasitic organisms exploit/subvert as hosts. As a result, many investigators introduced the objectives of their analysis by referring to "host-pathogen" interactions. Though we, as investigators, are all determined to decipher the pathogenic processes which can indeed be coupled to the parasite uncontrolled development, I think that the parasites - alike the living organisms they subvert as hosts - need to be considered as living organisms per se, instead of being considered as "pathogens". Such a conceptual frame will promote research on the processes on which relies their perpetuation whatever the level under investigations - individual and/or population level. Only the unicellular protozoan parasites of the genus Leishmania known to be hosted by blood-feeding insects and mammals will be further considered in this brief contribution.

Recommended procedures and techniques for the petrographic description of bituminous coals

USGS Publications Warehouse

Chao, E.C.T.; Minkin, J.A.; Thompson, C.L.

1982-01-01

Modern coal petrology requires rapid and precise description of great numbers of coal core or bench samples in order to acquire the information required to understand and predict vertical and lateral variation of coal quality for correlation with coal-bed thickness, depositional environment, suitability for technological uses, etc. Procedures for coal description vary in accordance with the objectives of the description. To achieve our aim of acquiring the maximum amount of quantitative information within the shortest period of time, we have adopted a combined megascopic-microscopic procedure. Megascopic analysis is used to identify the distinctive lithologies present, and microscopic analysis is required only to describe representative examples of the mixed lithologies observed. This procedure greatly decreases the number of microscopic analyses needed for adequate description of a sample. For quantitative megascopic description of coal microlithotypes, microlithotype assemblages, and lithotypes, we use (V) for vitrite or vitrain, (E) for liptite, (I) for inertite or fusain, (M) for mineral layers or lenses other than iron sulfide, (S) for iron sulfide, and (X1), (X2), etc. for mixed lithologies. Microscopic description is expressed in terms of V representing the vitrinite maceral group, E the exinite group, I the inertinite group, and M mineral components. volume percentages are expressed as subscripts. Thus (V)20(V80E10I5M5)80 indicates a lithotype or assemblage of microlithotypes consisting of 20 vol. % vitrite and 80% of a mixed lithology having a modal maceral composition V80E10I5M5. This bulk composition can alternatively be recalculated and described as V84E8I4M4. To generate these quantitative data rapidly and accurately, we utilize an automated image analysis system (AIAS). Plots of VEIM data on easily constructed ternary diagrams provide readily comprehended illustrations of the range of modal composition of the lithologic units making up a given coal bed. The use of bulk-specific-gravity determinations is alo recommended for identification and characterization of the distinctive lithologic units. The availability of an AIAS also enhances the capability to acquire textural information. Ranges of size of maceral and mineral grains can be quickly and precisely determined by use of an AIAS. We assume that shape characteristics of coal particles can also be readily evaluated by automated image analysis, although this evaluation has not yet been attempted in our laboratory. Definitive data on the particulate mineral content of coal constitute another important segment of petrographic description. Characterization of mineral content may be accomplished by optical identification, electron microprobe analysis, X-ray diffraction, and scanning and transmission electron microscopy. Individual mineral grains in place in polished blocks or polished this sections, or separated from the coal matrix by sink-float methods are studied by analytical techniques appropriate to the conditions of sampling. Finally, whenever possible, identification of the probable genus or plant species from which a given coal component is derived will add valuable information and meaning to the petrographic description. ?? 1982.

Off-design performance analysis of MHD generator channels

NASA Technical Reports Server (NTRS)

Wilson, D. R.; Williams, T. S.

1980-01-01

A computer code for performing parametric design point calculations, and evaluating the off-design performance of MHD generators has been developed. The program is capable of analyzing Faraday, Hall, and DCW channels, including the effect of electrical shorting in the gas boundary layers and coal slag layers. Direct integration of the electrode voltage drops is included. The program can be run in either the design or off-design mode. Details of the computer code, together with results of a study of the design and off-design performance of the proposed ETF MHD generator are presented. Design point variations of pre-heat and stoichiometry were analyzed. The off-design study included variations in mass flow rate and oxygen enrichment.

Who Needs Critical Agency?: Educational Research and the Rhetorical Economy of Globalization

ERIC Educational Resources Information Center

Rice, J. A.; Vastola, Michael

2011-01-01

Current critical pedagogical scholarship has theorized the epistemological and social intersection between globalization and educational technology according to two distinct positions. For some, this intersection offers new liberatory knowledges and opportunities that can subvert social homogenization and economic disparity. For others, this…

Student Authority: Antidote to Alienation

ERIC Educational Resources Information Center

Goodman, Joan

2010-01-01

The widespread disaffection of students from school is manifested in academic failure, indifference, and defiance. These problems can be alleviated, I argue, when an authority structure is developed that combines three components--freedom, power, and legitimacy. Authority understood as either power or freedom is apt to subvert students' school…

Postmylonitic deformation in the Raft River metamorphic core complex, northwestern Utah: Evidence of a rolling hinge

NASA Astrophysics Data System (ADS)

Manning, Andrew H.; Bartley, John M.

1994-06-01

Much of the recent debate over low-angle normal faults exposed in metamorphic core complexes has centered on the rolling hinge model. The model predicts tilting of seismogenic high-angle normal faults to lower dips by footwall deformation in response to isostatic forces caused by footwall exhumation. This shallow brittle deformation should visibly overprint the mylonitic fabric in the footwall of a metamorphic core complex. The predicted style and magnitude of rolling hinge strain depends upon the macroscopic mechanism by which the footwall deforms. Two end-members have been proposed: subvertical simple shear and flexural failure. Each mechanism should generate a distinctive pattern of structures that strike perpendicular to the regional extension direction. Subvertical simple shear (SVSS) should generate subvertical faults and kink bands with a shear sense antithetic to the detachment. For an SVSS hinge, the hinge-related strain magnitude should depend only on initial fault dip; rolling hinge structures should shorten the mylonitic foliation by >13% for an initial fault dip of >30°. In flexural failure the footwall behaves as a flexed elastic beam that partially fails in response to bending stresses. Resulting structures include conjugate faults and kink bands that both extend and contract the mylonitic foliation. Extensional sets could predominate as a result of superposition of far-field and flexural stresses. Strain magnitudes do not depend on fault dip but depend on the thickness and radius of curvature of the flexed footwall beam and vary with location within that beam. Postmylonitic structures were examined in the footwall of the Raft River metamorphic core complex in northwestern Utah to test these predictions. Observed structures strike perpendicular to the regional extension direction and include joints, normal faults, tension-gash arrays, and both extensional and contractional kink bands. Aside from the subvertical joints, the extensional structures dip moderately to steeply and are mainly either synthetic to the detachment or form conjugate sets. Range-wide, the extensional structures accomplish about 4% elongation of the mylonitic foliation. Contractional structures dip steeply, mainly record shear antithetic to the detachment, and accomplish <1% contraction of the foliation. These observations are consistent with the presence of a rolling hinge in the Raft River Mountains, but a rolling hinge that reoriented a high-angle normal fault by SVSS is excluded. The pattern and magnitudes of strain favor hinge-related deformation mainly by flexural failure with a subordinate component of SVSS.

DEEP BIOSPHERE. Exploring deep microbial life in coal-bearing sediment down to ~2.5 km below the ocean floor.

PubMed

Inagaki, F; Hinrichs, K-U; Kubo, Y; Bowles, M W; Heuer, V B; Hong, W-L; Hoshino, T; Ijiri, A; Imachi, H; Ito, M; Kaneko, M; Lever, M A; Lin, Y-S; Methé, B A; Morita, S; Morono, Y; Tanikawa, W; Bihan, M; Bowden, S A; Elvert, M; Glombitza, C; Gross, D; Harrington, G J; Hori, T; Li, K; Limmer, D; Liu, C-H; Murayama, M; Ohkouchi, N; Ono, S; Park, Y-S; Phillips, S C; Prieto-Mollar, X; Purkey, M; Riedinger, N; Sanada, Y; Sauvage, J; Snyder, G; Susilawati, R; Takano, Y; Tasumi, E; Terada, T; Tomaru, H; Trembath-Reichert, E; Wang, D T; Yamada, Y

2015-07-24

Microbial life inhabits deeply buried marine sediments, but the extent of this vast ecosystem remains poorly constrained. Here we provide evidence for the existence of microbial communities in ~40° to 60°C sediment associated with lignite coal beds at ~1.5 to 2.5 km below the seafloor in the Pacific Ocean off Japan. Microbial methanogenesis was indicated by the isotopic compositions of methane and carbon dioxide, biomarkers, cultivation data, and gas compositions. Concentrations of indigenous microbial cells below 1.5 km ranged from <10 to ~10(4) cells cm(-3). Peak concentrations occurred in lignite layers, where communities differed markedly from shallower subseafloor communities and instead resembled organotrophic communities in forest soils. This suggests that terrigenous sediments retain indigenous community members tens of millions of years after burial in the seabed. Copyright © 2015, American Association for the Advancement of Science.

Single-layer transition metal sulfide catalysts

DOEpatents

Thoma, Steven G [Albuquerque, NM

2011-05-31

Transition Metal Sulfides (TMS), such as molybdenum disulfide (MoS.sub.2), are the petroleum industry's "workhorse" catalysts for upgrading heavy petroleum feedstocks and removing sulfur, nitrogen and other pollutants from fuels. We have developed an improved synthesis technique to produce SLTMS catalysts, such as molybdenum disulfide, with potentially greater activity and specificity than those currently available. Applications for this technology include heavy feed upgrading, in-situ catalysis, bio-fuel conversion and coal liquefaction.

Petrography of Permian "Gondwana" coals from boreholes in northwestern Bangladesh, based on semiautomated reflectance scanning

USGS Publications Warehouse

Bostick, N.H.; Betterton, W.J.; Gluskoter, H.J.; Nazrul, Islam M.

1991-01-01

Drilling through Quaternary alluvium and Tertiary cover at low-gravity anomalies in northwestern Bangladesh showed the presence of Permian sedimentary rocks in depressions that may be as much as a thousand meters deep in the crystalline basement. These Permian strata include low-sulfur, high-volatile bituminous coals in beds as thick as 15 m. The maceral group composition of these coals was determined by semiautomated reflectance scanning with a motorized microscope stage, rather than by point counting. This method was chosen to give objectively recorded raw analytical data and to provide a graphical picture of each sample. The coals are mostly "Gondwana" type (poorly layered "plum pudding" with abundant minerals and inertinite in a vitrinite groundmass) that would be classed as semi-dull (inerto-gelitite) coals. However, six samples have more than 70% vitrinite. None of the samples would be classed as sapropelic (liptinitic). The upper, middle, and lower main seams in borehole GDH-45 were sampled in 10 benches (0.1-3 m thick) each. Inertinite ranges from 7 to 100 vol% (mineral free basis) in individual benches, but composite seam averages are 41, 54 and 67%. Inertinite increases toward the top of two main seams so the bottom would yield the most valuable first mine slices. Some benches with extremely high inertinite content, such as the top 7 m of the lower thick seam, might be mined specially for blending with foreign low-inert coals to increase coke strength. The free swelling index reaches 7.5 in several vitrinite-rich benches, which can indicate good coking coal. Much of the vitrinite is fluorescent, which indicates secondary bituminization characteristic of vitrinite in good coking coals. Ash yields range from 8 to 52%, with composite seam averages of 15, 14 and 24%. Rare visible pyrite is in veinlets or small nodules; framboids and dispersed pyrite are absent. In borehole GDH-40 near Barapukuria (200-500 m depth), the mean random reflectance of vitrinite "A" ranges from 0.60 to 0.80% Ro and vitrinite "B" ranges from 0.55 to 0.65%. In borehole GDH-45 near Khalaspir (287-442 m), the reflectance of vitrinite ranges from 0.79 to 0.94%. In individual cases, the vitrinite is difficult to define because of semivitrinite at higher reflectance (forming a separate peak on several reflectograms) and because of surface bitumen films or resinous (?) inclusions at lower reflectance. On the basis of vitrinite reflectance, the coals can be considered to have entered the "main phase of bitumen generation" of organic thermal maturation as understood in petroleum geochemistry. ?? 1991.

Comparative analysis of signature genes in PRRSV-infected porcine monocyte-derived cells at differential activation statuses

USDA-ARS?s Scientific Manuscript database

Activation statuses of monocytic cells are critically important for antiviral immunity. Devastating viruses like porcine reproductive and respiratory syndrome virus (PRRSV) are capable of directly infecting these cells, subverting host immunity. Monocyte-derived DCs (mDCs) are major target cells in ...

Oh to Be Rid of Administrative Wimps!

ERIC Educational Resources Information Center

Weissberg, Robert

2007-01-01

Contemporary university administrators are usually wimps, and timidity in facing easily enraged campus radicals only invites outrageous demands which, in turn, subvert intellectual life. This must be changed. For much of human history leaders had to display physical valor and this trait should be restored to the college administrator job…

Somewhere between What Is and What If: Fictionalisation and Ethnographic Inquiry

ERIC Educational Resources Information Center

Reed, Malcolm

2011-01-01

Fictionalisation seems to render ethnographic inquiry suspect as research appropriate to the social sciences because it subverts a claim of realism or objectivity. This leads some ethnographers to propose alternative criteria for validation, such as participation and evocation, which offer alignment with realism; others suggest that scientific…

A Bakhtinian Reading of John Donne's Parody Poem "The Bait"

ERIC Educational Resources Information Center

Alareer, Refaat; Omar, Noritah; Kaur, Hardev

2017-01-01

While conventional critics seek the comic aspect of parody, modernist critics credit parody with questioning mainstream literary trends and subverting literary production. For instance, Mikhail Bakhtin believes in parody's power to create "a decrowning double" by turning the official worldview up-side-down. For experimental poets like…

Emerging Pedagogy: Teaching Digital Hypertexts in Social Contexts.

ERIC Educational Resources Information Center

Strasma, Kip

2001-01-01

Considers how in the classroom, particularly, teachers should take advantage of the multiple aspects of narrative time constructed through hypertextual duration, frequency, and order. Uses an ethnographic study of two college courses to illustrate several of these opportunities as they subvert the dominant orders of textuality totalized by…

Subverting the Hegemony of Risk: Vulnerability and Transformation among Australian Show Children

ERIC Educational Resources Information Center

Danaher, P. A.; Danaher, Geoff; Moriarty, Beverley

2007-01-01

Background: Australian show people traverse extensive coastal and inland circuits in eastern and northern Australia, bringing the delights of "sideshow alley" to annual agricultural shows. The show people's mobility for most of the school year makes it difficult for their school-age children to attend "regular" schools…

Resisting Social Justice in Leadership Preparation Programs: Mechanisms that Subvert

ERIC Educational Resources Information Center

Hernandez, Frank; McKenzie, Kathryn Bell

2010-01-01

It is well documented that the achievement gap between affluent students and economically disadvantaged students and between White students and students of color continues to widen. In addition to these achievement gaps, marginalizing practices are often imbedded in the structures of schooling. These challenges require educational leadership…

Engineering a "Contact Zone" through Translanguaging

ERIC Educational Resources Information Center

Helm, Francesca; Dabre, Tejane

2018-01-01

This paper presents a pilot project which uses a translanguaging approach in order to subvert the power dynamics whereby language learners, refugees and migrants are positioned as defective or ineffective communicators of a target language. The project seeks to create a space, an engineered "contact zone" in which the negative,…

Writing Queer across the Borders of Geography and Desire

ERIC Educational Resources Information Center

Malagreca, Miguel A.

2009-01-01

In this article, the author merges biographical notes, autoethnography and experimental writing to situate his migrant self as a self that "performs through writing," i.e. planned, experimental writing that subverts the centrality of the monolingual heterosexual identity. He explores the intersections of time, desire, and power across…

On Being an Angry Black Man

ERIC Educational Resources Information Center

Quaye, Stephen John

2017-01-01

Black men are often seen as problems, threats, and thugs. The mere existence of a Black body is often met with fear. Using autoethnographic mystory, I blend personal stories, poetry, song lyrics, and analysis to subvert the angry Black man mantra and explore the productive use of anger to stimulate change.

Neoliberalism, Democracy and the University as a Public Sphere: An Interview with Henry A. Giroux

ERIC Educational Resources Information Center

Harper, Victoria

2014-01-01

"Truthout" contributor, director of "Truthout's" Public Intellectual Project (truth-out.org/public-intellectual-project) and Truthout board member Henry A. Giroux responds to questions about how the excesses of neoliberal politics have reshaped and subverted the democratic mission of higher education.

The (Be)Comings and Goings of "Developmental Disabilities": The Cultural Politics of "Impairment"

ERIC Educational Resources Information Center

Goodley, Dan; Roets, Griet

2008-01-01

Disability should be a concern for those interested in analysing and subverting the cultural politics of education. In this paper we address this concern through connecting critical analyses of "developmental disabilities" (formerly "mental retardation"), disability studies and poststructuralism. We target normative constructions of "developmental…

Industrialized Higher Education and Its Sustainable Alternatives

ERIC Educational Resources Information Center

Ostenson, Joseph A.; Clegg, Joshua W.; Wiggins, Bradford J.

2017-01-01

We argue that academic life is increasingly giving way to forces of industrialization and that many of the problems confronting higher education arise within this transformation. We discuss how a culture of standardization has led to academic monocultures; how faculty autonomy has been subverted by topdown management structures; how locally based…

Importance of weak minerals on earthquake mechanics

NASA Astrophysics Data System (ADS)

Kaneki, S.; Hirono, T.

2017-12-01

The role of weak minerals such as smectite and talc on earthquake mechanics is one of the important issues, and has been debated for recent several decades. Traditionally weak minerals in fault have been reported to weaken fault strength causing from its low frictional resistance. Furthermore, velocity-strengthening behavior of such weak mineral (talc) is considered to responsible for fault creep (aseismic slip) in the San Andreas fault. In contrast, recent studies reported that large amount of weak smectite in the Japan Trench could facilitate gigantic seismic slip during the 2011 Tohoku-oki earthquake. To investigate the role of weak minerals on rupture propagation process and magnitude of slip, we focus on the frictional properties of carbonaceous materials (CMs), which is the representative weak materials widely distributed in and around the convergent boundaries. Field observation and geochemical analyses revealed that graphitized CMs-layer is distributed along the slip surface of a fossil plate-subduction fault. Laboratory friction experiments demonstrated that pure quartz, bulk mixtures with bituminous coal (1 wt.%), and quartz with layered coal samples exhibited almost similar frictional properties (initial, yield, and dynamic friction). However, mixtures of quartz (99 wt.%) and layered graphite (1 wt.%) showed significantly lower initial and yield friction coefficient (0.31 and 0.50, respectively). Furthermore, the stress ratio S, defined as (yield stress-initial stress)/(initial stress-dynamic stress), increased in layered graphite samples (1.97) compared to quartz samples (0.14). Similar trend was observed in smectite-rich fault gouge. By referring the reported results of dynamic rupture propagation simulation using S ratio of 1.4 (typical value for the Japan Trench) and 2.0 (this study), we confirmed that higher S ratio results in smaller slip distance by approximately 20 %. On the basis of these results, we could conclude that weak minerals have lower initial/yield strength and higher S ratio, and thus restrain magnitude of slip during earthquake.

Assessment of burned coal shale properties based on cyclic load

NASA Astrophysics Data System (ADS)

Grygierek, Marcin; Kalisz, Piotr; Pacześniowski, Krzysztof; Pytlik, Andrzej; Zięba, Magdalena

2018-04-01

Road surfaces that are subjected to cyclic loads generated by vehicle wheels must meet the requirements concerning the durability in the assumed period of use. The durability of the layered pavement construction systems depends on the value and frequency of the load as well as on the mechanical features of its individual layers. Layers of unbound, mechanically stabilized mixtures are a significant aspect of surfaces that are susceptible. Mixtures of this type can be applied both to the subgrade layers as well as to the bottom pavement layers, including the improved course. Considering the cyclic nature of the load on the surface of the entire system, mechanically stabilized layers are subject to continuous, but slow, densification during the period of use, which results in the formation of permanent deformations and so-called structural ruts. Post-mining waste is frequently used in road construction. which is the so-called burned shale that can be used for the bottom layers of the surface and layers of the improved subgrade (soil replacement). This material was the subject of the analysis. The evaluation was based mainly on the results of pilot studies covering cyclic loads of the layer/course made of the so-called red shale. The applied research method was aimed at preliminary assessment of its suitability for the assessment of the behaviour of the disintegrated medium under the conditions of test loads simulating the movement of vehicles.

Effects of the state of Co species in Co/Al2O3 catalysts on the catalytic performance of propane dehydrogenation

NASA Astrophysics Data System (ADS)

Li, Xiuyi; Wang, Pengzhao; Wang, Haoren; Li, Chunyi

2018-05-01

In this paper, the Co/Al2O3 catalyst was prepared by incipient wetness impregnation method, and different post treatment methods were used to promote its dehydrogenation properties. Interestingly, we found that Co/Al2O3 catalysts with different post treatment protocols exhibited totally different catalytic behaviors in propane dehydrogenation. Fresh catalyst showed an induction period and was highly active for pyrolysis and coking at 10-30 min of reaction. The pre-reduction led to complete pyrolysis and coking at the beginning of reaction. However, the re-oxidation treatment gave a high selectivity (∼93.0%) to propylene at the whole process. XRD, H2-TPR, XPS, TEM and hydrogen chemisorption investigations showed that the post treatment has a great impact on the state of cobalt species and the performance of propane dehydrogenation over Co/Al2O3 catalysts. Specifically, the poorly dispersed metal Co led to pyrolysis and coking, while highly dispersed metal Co were responsible for the dehydrogenation of propane. The large Co3O4 particles (DFresh = 33.68 nm) result in the large metal Co grains (DPre-reduced = 24.90 nm) after the reduction or reaction process. While during the re-oxidization process, the surface metal Co was re-oxidized in a mild environment and got re-dispersion (DRe-oxidized = 6.07 nm). And the surface cobalt oxides layer is more readily to be reduced to metal Co during the reaction thus leading to the shortened induction period.

Investigations of ash fouling with cattle wastes as reburn fuel in a small-scale boiler burner under transient conditions.

PubMed

Oh, Hyukjin; Annamalai, Kalyan; Sweeten, John M

2008-04-01

Fouling behavior under reburn conditions was investigated with cattle wastes (termed as feedlot biomass [FB]) and coal as reburn fuels under a transient condition and short-time operation. A small-scale (30 kW or 100,000 Btu/hr) boiler burner research facility was used for the reburn experiments. The fuels considered for these experiments were natural gas (NG) for the ashless case, pure coal, pure FB, and blends of coal and FB. Two parameters that were used to characterize the ash "fouling" were (1) the overall heat-transfer coefficient (OHTC) when burning NG and solid fuels as reburn fuels, and (2) the combustible loss through ash deposited on the surfaces of heat exchanger tubes and the bottom ash in the ash port. A new methodology is presented for determining ash-fouling behavior under transient conditions. Results on the OHTCs for solid reburn fuels are compared with the OHTCs for NG. It was found that the growth of the layer of ash depositions over longer periods typically lowers OHTC, and the increased concentration of ash in gas phase promotes radiation in high-temperature zones during initial periods while decreasing the heat transfer in low-temperature zones. The ash analyses indicated that the bottom ash in the ash port contained a smaller percentage of combustibles with a higher FB percentage in the fuels, indicating better performance compared with coal because small particles in FB burn faster and the FB has higher volatile matter on a dry ash-free basis promoting more burn out.

Impacts of detrital nano- and micro-scale particles (dNP) on contaminant dynamics in a coal mine AMD treatment system.

PubMed

Lefticariu, Liliana; Sutton, Stephen R; Bender, Kelly S; Lefticariu, Mihai; Pentrak, Martin; Stucki, Joseph W

2017-01-01

Pollutants in acid mine drainage (AMD) are usually sequestered in neoformed nano- and micro-scale particles (nNP) through precipitation, co-precipitation, and sorption. Subsequent biogeochemical processes may control nNP stability and thus long-term contaminant immobilization. Mineralogical, chemical, and microbiological data collected from sediments accumulated over a six-year period in a coal-mine AMD treatment system were used to identify the pathways of contaminant dynamics. We present evidence that detrital nano- and micron-scale particles (dNP), composed mostly of clay minerals originating from the partial weathering of coal-mine waste, mediated biogeochemical processes that catalyzed AMD contaminant (1) immobilization by facilitating heterogeneous nucleation and growth of nNP in oxic zones, and (2) remobilization by promoting phase transformation and reductive dissolution of nNP in anoxic zones. We found that dNP were relatively stable under acidic conditions and estimated a dNP content of ~0.1g/L in the influent AMD. In the AMD sediments, the initial nNP precipitates were schwertmannite and poorly crystalline goethite, which transformed to well-crystallized goethite, the primary nNP repository. Subsequent reductive dissolution of nNP resulted in the remobilization of up to 98% of S and 95% of Fe accompanied by the formation of a compact dNP layer. Effective treatment of pollutants could be enhanced by better understanding the complex, dynamic role dNP play in mediating biogeochemical processes and contaminant dynamics at coal-mine impacted sites. Copyright © 2016 Elsevier B.V. All rights reserved.

Selective recovery of salt from coal gasification brine by nanofiltration membranes.

PubMed

Li, Kun; Ma, Wencheng; Han, Hongjun; Xu, Chunyan; Han, Yuxing; Wang, Dexin; Ma, Weiwei; Zhu, Hao

2018-06-20

The selective extraction and concentration of salt from coal gasification brine (CGB) by nanofiltration membranes is a promising technology to achieve near-zero liquid discharge of coal gasification wastewater. To investigate the feasibility of recovery of salts and the interaction of organic compounds, multivalent ions and monovalent ions on the rejection ratio, three nanofiltration membranes (OWNF1, NF270 and Desal-5 DK) with an 1812 spiral-wound module were used in crossflow filtration. The rejection mechanism was analyzed by comparing the rejection performance as a function of the operation pressure (increasing from 1.0 MPa to 2.5 MPa), the concentration (increasing from 10,000 mg/L to 25,000 mg/L) and pH values (increasing from 3.0 to 10.0). The concentrations of anions and cations were determined using an ion chromatographic analyzer and an inductively coupled plasma emission spectrometer, respectively. The results show that the rejection of sulfate and the chemical oxygen demand were higher than 92.12% and 78.84%, respectively, at appropriate operation, while negative rejection of chloride was observed in the CGB. The decreasing rejection of organic compounds was due to swelling of the membrane pore in high-concentration solutions. Meanwhile, the organic compounds weakened the negative charge of the membrane active layer, consequently decreasing the ion rejection. More than 85% of the sodium chloride could be recovered, indicating that this technology is suitable for resource recovery from CGB and near-zero liquid discharge of coal gasification industry. Copyright © 2018 Elsevier Ltd. All rights reserved.

One microenvironment does not fit all: heterogeneity beyond cancer cells.

PubMed

Kim, Ik Sun; Zhang, Xiang H-F

2016-12-01

Human cancers exhibit formidable molecular heterogeneity, to a large extent accounting for the incomplete and transitory efficacy of current anti-cancer therapies. However, neoplastic cells alone do not manifest the disease, but conscript a battery of non-tumor cells to enable and sustain hallmark capabilities of cancer. Escaping immunosurveillance is one of such capabilities. Tumors evolve immunosuppressive microenvironment to subvert anti-tumor immunity. In this review, we will focus on tumor-associated myeloid cells, which constitute an essential part of the immune microenvironment and reciprocally interact with cancer cells to establish malignancy toward metastasis. The diversity and plasticity of these cells constitute another layer of heterogeneity, beyond the heterogeneity of cancer cells themselves. We envision that immune microenvironment co-evolves with the genetic heterogeneity of tumor. Addressing the question of how genetically distinct tumors shape and are shaped by unique immune microenvironment will provide an attractive rationale to develop novel immunotherapeutic modalities. Here, we discuss the complex nature of tumor microenvironment, with an emphasis on the cellular and functional heterogeneity among tumor-associated myeloid cells as well as immune environment heterogeneity in the context of a full spectrum of human breast cancers.

Energy conservation in the earth's crust and climate change.

PubMed

Mu, Yao; Mu, Xinzhi

2013-02-01

Among various matters which make up the earth's crust, the thermal conductivity of coal, oil, and oil-gas, which are formed over a long period of geological time, is extremely low. This is significant to prevent transferring the internal heat of the earth to the thermal insulation of the surface, cooling the surface of the earth, stimulating biological evolution, and maintaining natural ecological balance as well. Fossil energy is thermal insulating layer in the earth's crust. Just like the function of the thermal isolation of subcutaneous fatty tissue under the dermis of human skin, it keeps the internal heat within the organism so it won't be transferred to the skin's surface and be lost maintaining body temperature at low temperatures. Coal, oil, oil-gas, and fat belong to the same hydrocarbons, and the functions of their thermal insulation are exactly the same. That is to say, coal, oil, and oil-gas are just like the earth's "subcutaneous fatty tissue" and objectively formed the insulation protection on earth's surface. This paper argues that the human large-scale extraction of fossil energy leads to damage of the earth's crust heat-resistant sealing, increasing terrestrial heat flow, or the heat flow as it is called, transferring the internal heat of the earth to Earth's surface excessively, and causing geotemperature and sea temperature to rise, thus giving rise to global warming. The reason for climate warming is not due to the expansion of greenhouse gases but to the wide exploitation of fossil energy, which destroyed the heat insulation of the earth's crust, making more heat from the interior of the earth be released to the atmosphere. Based on the energy conservation principle, the measurement of the increase of the average global temperature that was caused by the increase of terrestrial heat flow since the Industrial Revolution is consistent with practical data. This paper illustrates "pathogenesis" of climate change using medical knowledge. The mathematical verification is based on the principle of energy conservation. The central idea or clou in this paper is that fossil energy is a thermal insulating layer in the earth's crust, the thermal insulating layer was destroyed after human large-scale mining of fossil energy, and the internal heat of the earth was excessively released to the surface so as to cause climate change.

Chemical reaction mechanisms between Y2O3 stabilized ZrO2 and Gd doped CeO2 with PH3 in coal syngas

NASA Astrophysics Data System (ADS)

Chen, Gang; Kishimoto, Haruo; Yamaji, Katsuhiko; Kuramoto, Koji; Gong, Mingyang; Liu, Xingbo; Hackett, Gregory; Gerdes, Kirk; Horita, Teruhisa

2014-12-01

To clarify the chemical stability of the key materials exposed to coal syngas (CSG) containing PH3 contaminant atmosphere, exposure tests of Y2O3 8 mol.% stabilized ZrO2 (YSZ) and Gd doped CeO2 (GDC) are carried out in simulated CSG with different concentrations of PH3. Significant reaction between YSZ and 10 ppm PH3 in CSG atmosphere is confirmed, and no obvious reaction is detected on the surface of YSZ after exposed in CSG with 1 ppm PH3. YPO4, Zr2.25(PO4)3 and monoclinic Y partial stabilized ZrO2 (m-PSZ) are identified on the YSZ pellet surface after exposed in CSG with 10 ppm PH3. GDC reacted with PH3 even at 1 ppm concentration. A (Ce0.9Gd0.1)PO4 layer is formed on the surface of GDC pellet after exposure in CSG with 10 ppm PH3. Possible reaction mechanisms between YSZ and GDC with PH3 in CSG are clarified. Compared with GDC, YSZ exhibits sufficient phosphorus resistance for devices directly exposed to a coal syngas atmosphere containing low concentration of PH3.

Synthetic Coal Slag Infiltration into Varying Refractory Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaneko, Tetsuya K; Thomas, Hugh; Bennett, James P

The infiltrations of synthetic coal slag into 99%Al{sub 2}O{sub 3}, 85%Al{sub 2}O{sub 3}–15%SiO{sub 2}, and 90%Cr{sub 2}O{sub 3}–10%Al{sub 2}O{sub 3} refractories with a temperature gradient induced along the penetration direction were compared to one another. The infiltrating slag was synthesized with a composition that is representative of an average of the ash contents from U S coal feedstock. Experiments were conducted with a hot-face temperature of 1450°C in a CO/CO{sub 2} atmosphere. Minimal penetration was observed in the 90%Cr{sub 2}O{sub 3}–10%Al{sub 2}O{sub 3} material because interactions between the refractory and the slag produced a protective layer of FeCr{sub 2}O{sub 4},more » which impeded slag flow into the bulk of the refractory. After 5 h, the 99%Al{sub 2}O{sub 3} sample exhibited an average penetration of 12.7 mm whereas the 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} sample showed 3.8 mm. Slag infiltrated into the 99%Al{sub 2}O{sub 3} and 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} refractory systems by dissolving the respective refractories' matrix materials, which consist of fine Al{sub 2}O{sub 3} particles and an amorphous alumino-silicate phase. Due to enrichment in SiO{sub 2}, a network-former, infiltration into the 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} system yielded a higher viscosity slag and hence, a shallower penetration depth. The results suggest that slag infiltration can be limited by interactions with the refractory through the formation of either a solid layer that physically impedes fluid flow or a more viscous slag that retards infiltration.« less

Assessing the environmental sustainability of electricity generation in Chile.

PubMed

Gaete-Morales, Carlos; Gallego-Schmid, Alejandro; Stamford, Laurence; Azapagic, Adisa

2018-09-15

Around 40% of electricity in Chile is supplied by renewables and the rest by fossil fuels. Despite the growing electricity demand in the country, its environmental impacts are as yet unknown. To address this gap, the current study presents the first comprehensive assessment of the life cycle environmental sustainability of electricity generation in Chile. Both the individual sources and the electricity mix over the past 10 years are considered. The following sources present in the electricity mix are evaluated: coal, oil, natural gas, biogas, biomass, wind, solar photovoltaics (PV) and hydropower. In total, 10 electricity technologies and 174 power plants installed across the country have been considered. Eleven environmental impacts have been estimated, including global warming, human toxicity, ecotoxicities, as well as resource and ozone layer depletion. The results reveal that hydropower is environmentally the most sustainable option across the impacts, followed by onshore wind and biogas. Electricity from natural gas has 10%-84% lower impacts than biomass for seven categories. It is also 13%-98% better than solar PV for six impacts and 17%-66% than wind for four categories. Solar PV has the highest abiotic depletion potential due to the use of scarce elements in the manufacture of panels. While electricity generation has grown by 44% in the past 10 years, all the impacts except ozone layer depletion have increased by 1.6-2.7 times. In the short term, environmental regulations should be tightened to improve the emissions control from coal and biomass plants. In the medium term, the contribution of renewables should be ramped up, primarily increasing the hydro, wind and biogas capacity. Coal and oil should be phased out, using natural gas as a transitional fuel to help the stability of the grid with the increasing contribution of intermittent renewables. Copyright © 2018 Elsevier B.V. All rights reserved.

Origin and significance of high nickel and chromium concentrations in pliocene lignite of the Kosovo Basin, Serbia

USGS Publications Warehouse

Ruppert, L.; Finkelman, R.; Boti, E.; Milosavljevic, M.; Tewalt, S.; Simon, N.; Dulong, F.

1996-01-01

Trace element data from 59 Pliocene lignite cores from the lignite field in the Kosovo Basin, southern Serbia, show localized enrichment of Ni and Cr (33-304 ppm and 8-176 ppm, respectively, whole-coal basis). Concentrations of both elements decrease from the western and southern boundaries of the lignite field. Low-temperature ash and polished coal pellets of selected bench and whole-coal samples were analyzed by X-ray diffraction and scanning electron microscopy with energy-dispersive X-ray analyses. These analyses show that most of the Ni and Cr are incorporated in detrital and, to a lesser degree, in authigenic minerals. The Ni- and Cr-bearing detrital minerals include oxides, chromites, serpentine-group minerals and rare mixed-layer clays. Possible authigenic minerals include Ni-Fe sulfates and sulfides. Analyses of three lignite samples by a supercritical fluid extraction technique indicate that some (1-11%) of the Ni is organically bound. Ni- and Cr-bearing oxides, mixed-layer clays, chromites and serpentine-group minerals were also identified in weathered and fresh samples of laterite developed on serpentinized Paleozoic peridotite at the nearby Glavica and C??ikatovo Ni mines. These mines are located along the western and northwestern rim, respectively, of the Kosovo Basin, where Ni contents are highest. The detrital Ni- and Cr-bearing minerals identified in lignite samples from the western part of the Kosovo Basin may have been transported into the paleoswamp by rivers that drained the two Paleocene laterites. Some Ni may have been transported directly into the paleoswamp in solution or, alternatively, Ni may have been leached from detrital minerals by acidic peat water and adsorbed onto organic matter and included into authigenic mineral phases. No minable source of Ni and Cr is known in the southern part of the lignite field; however, the mineral and chemical data from the lignite and associated rocks suggest that such a source area may exist.

A low-cost mullite-titania composite ceramic hollow fiber microfiltration membrane for highly efficient separation of oil-in-water emulsion.

PubMed

Zhu, Li; Chen, Mingliang; Dong, Yingchao; Tang, Chuyang Y; Huang, Aisheng; Li, Lingling

2016-03-01

Oil-in-water (O/W) emulsion is considered to be difficult to treat. In this work, a low-cost multi-layer-structured mullite-titania composite ceramic hollow fiber microfiltration membrane was fabricated and utilized to efficiently remove fine oil droplets from (O/W) emulsion. In order to reduce membrane cost, coal fly ash was effectively recycled for the first time to fabricate mullite hollow fiber with finger-like and sponge-like structures, on which a much more hydrophilic TiO2 layer was further deposited. The morphology, crystalline phase, mechanical and surface properties were characterized in details. The filtration capability of the final composite membrane was assessed by the separation of a 200 mg·L(-1) synthetic (O/W) emulsion. Even with this microfiltration membrane, a TOC removal efficiency of 97% was achieved. Dilute NaOH solution backwashing was used to effectively accomplish membrane regeneration (∼96% flux recovery efficiency). This study is expected to guide an effective way to recycle waste coal fly ash not only to solve its environmental problems but also to produce a high-valued mullite hollow fiber membrane for highly efficient separation application of O/W emulsion with potential simultaneous functions of pure water production and oil resource recovery. Copyright © 2015 Elsevier Ltd. All rights reserved.

Hydrogeologic controls imposed by mechanical stratigraphy in layered rocks of the Châteauguay River Basin, a U.S.-Canada transborder aquifer

NASA Astrophysics Data System (ADS)

Morin, Roger; Godin, RéJean; Nastev, Miroslav; Rouleau, Alain

2007-04-01

The Châteauguay River Basin delineates a transborder watershed with roughly half of its surface area located in northern New York State and half in southern Québec Province, Canada. As part of a multidisciplinary study designed to characterize the hydrogeologic properties of this basin, geophysical logs were obtained in 12 wells strategically located to penetrate the four major sedimentary rock formations that constitute the regional aquifers. The layered rocks were classified according to their elastic properties into three primary units: soft sandstone, hard sandstone, and dolostone. Downhole measurements were analyzed to identify fracture patterns associated with each unit and to evaluate their role in controlling groundwater flow. Fracture networks are composed of orthogonal sets of laterally extensive, subhorizontal bedding plane partings and bed-delimited, subvertical joints with spacings that are consistent with rock mechanics principles and stress models. The vertical distribution of transmissive zones is confined to a few select bedding plane fractures, with soft sandstone having the fewest (one per 70-m depth) and hard sandstone the most (five per 70-m depth). Bed-normal permeability is examined using a probabilistic model that considers the lengths of flow paths winding along joints and bedding plane fractures. Soft sandstone has the smallest bed-normal permeability primarily because of its wide, geomechanically undersaturated joint spacing. Results indicate that the three formations have similar values of bulk transmissivity, within roughly an order of magnitude, but that each rock unit has its own unique system of groundwater flow paths that constitute that transmissivity.

Hydrogeologic controls imposed by mechanical stratigraphy in layered rocks of the Chateauguay River Basin, a U.S.-Canada transborder aquifer

USGS Publications Warehouse

Morin, Roger H.; Godin, Rejean; Nastev, Miroslav; Rouleau, Alain

2007-01-01

[1] The Châteauguay River Basin delineates a transborder watershed with roughly half of its surface area located in northern New York State and half in southern Québec Province, Canada. As part of a multidisciplinary study designed to characterize the hydrogeologic properties of this basin, geophysical logs were obtained in 12 wells strategically located to penetrate the four major sedimentary rock formations that constitute the regional aquifers. The layered rocks were classified according to their elastic properties into three primary units: soft sandstone, hard sandstone, and dolostone. Downhole measurements were analyzed to identify fracture patterns associated with each unit and to evaluate their role in controlling groundwater flow. Fracture networks are composed of orthogonal sets of laterally extensive, subhorizontal bedding plane partings and bed-delimited, subvertical joints with spacings that are consistent with rock mechanics principles and stress models. The vertical distribution of transmissive zones is confined to a few select bedding plane fractures, with soft sandstone having the fewest (one per 70-m depth) and hard sandstone the most (five per 70-m depth). Bed-normal permeability is examined using a probabilistic model that considers the lengths of flow paths winding along joints and bedding plane fractures. Soft sandstone has the smallest bed-normal permeability primarily because of its wide, geomechanically undersaturated joint spacing. Results indicate that the three formations have similar values of bulk transmissivity, within roughly an order of magnitude, but that each rock unit has its own unique system of groundwater flow paths that constitute that transmissivity.

The Problem of Propagation: Original Sin as Inherited Discourse

ERIC Educational Resources Information Center

Stillwaggon, James

2014-01-01

As Modernist doctrines emphasizing the unity and agency of the educated self are increasingly set up as the straw men of contemporary educational discourses, premodern and Medieval theories of selfhood tend to disappear from the horizon of educational thought altogether. In this essay, in order to subvert this overcoming of our intellectual past,…

Women's Career Investment and the Returns: Career Benefits and Barriers in the 21st Century Green Economy

ERIC Educational Resources Information Center

Johnson, Philomena M.

2010-01-01

The key to building successful strategies as a higher education practitioner promoting 21st century green economy career awareness for women attending urban universities, demands advocating for benefits, and subverting potential barriers, to positively influence career choices. Women's career investment and returns increase when proper strategies…

Uniting Students To Subvert the Testing and Technology Craze.

ERIC Educational Resources Information Center

Miller, Robert

This paper addresses the movement to "improve" schools by means of legislating mandatory testing and then publishing students' results in local newspapers and on the Internet. Students who attend schools where the standards are not met are often the ones who would benefit most from a broad-based language arts program. These students are…

Promises to Keep: The Continuing Crisis in the Education of Migrant Children.

ERIC Educational Resources Information Center

National Child Labor Committee, New York, NY.

Because the 1966 Programs for Migratory children amendment to Title I of the Elementary and Secondary Education Act has been improperly implemented and systematically subverted, and standards of administration and accountability have been disregarded, equal educational opportunity for migrant children is still not a reality. There are inherent…

"Cool" English: Stylized Native-Speaker English in Japanese Television Shows

ERIC Educational Resources Information Center

Furukawa, Gavin

2015-01-01

This article analyzes stylized pronunciations of English by Japanese speakers on televised variety shows in Japan. Research on style and mocking has done much to reveal how linguistic forms are utilized in interaction as resources of identity construction that can oftentimes subvert hegemonic discourse (Chun 2004). Within this research area,…

Subverting Ableist Discourses as an Exercise in Precarity: A Zimbabwean Case Study

ERIC Educational Resources Information Center

Chinyowa, Kennedy C.; Chivandikwa, Nehemiah

2017-01-01

This article focuses on how ableist discourses and practices seek to "normalize" the disabled body which is deemed to be "deviant". This leads to acts of normalization that expose disabled bodies to precarity, conceived here as the lived experience of marginalization, ostracism and vulnerability. Using the case study of a…

Burton Clark's "The Higher Education System: Academic Organization in Cross-National Perspective"

ERIC Educational Resources Information Center

Brennan, John

2010-01-01

In "The Higher Education System", Burton Clark provides a model for the organisational analysis of higher education institutions and systems. Central to the model are the concepts of knowledge, beliefs and authority. In particular, Clark examines how different interest groups both inside and outside the university shape and subvert the…

When Leadership and Policy Making Collide: The Valley View Middle School Experience

ERIC Educational Resources Information Center

Hodge, Warren A.; Osborne-Lampkin, La'Tara

2014-01-01

This case demonstrates the multifaceted nature of the school uniform debate. It shows how conflicts and tensions between stakeholder groups develop and persist when policymakers and school leaders allow hidden agendas and communication barriers to subvert the decision- and policymaking processes. In particular, the case demonstrates what happens…

Teaching Abjection: A Response to the War on Terror

ERIC Educational Resources Information Center

Cho, Daniel

2005-01-01

In this paper, the author discusses pedagogy and strategy within the current climate set by the "War on Terror". Deploying Lacanian psychoanalysis in a critique of standardized knowledge, the author develops a theory of "abject pedagogy" that seeks to subvert the current "regimes of truth" while providing educators with a viable pedagogy during…

Politics and Play: Meditations on Rhetorical Bodily Performance

ERIC Educational Resources Information Center

Pauliny, Tara

2013-01-01

Focusing on the drag king performances of Christie Whisman, who lived and worked in Columbus, Ohio, USA, from 1999 to 2001, this essay argues that rhetorical bodily performances have the capacity not only to subvert normalised notions of identity categories, but that such performances can also create alternate pedagogical sites that persuasively…

Heterophobia: Subverting Heterosexual Hegemony through Intermedial Applied Performance for Young People

ERIC Educational Resources Information Center

Phillips, Hannah

2016-01-01

This article responds to intermediality through a case study of an intermedial applied performance for young people. "Heterophobia," a hybrid fusion of live performance, digital technology, social media and urban street art, aimed to challenge homophobia in schools and online. Intermediality was used as a tool to enhance young people's…

Globalisation and Its Malcontents: In Pursuit of the Promise of Education

ERIC Educational Resources Information Center

Soudien, Crain

2005-01-01

In the course of exploring critiques of globalisation, this essay will focus on two postures--each with its range of arguments--that have emerged as alternatives to globalisation, namely, the delinking position and the subverting position. The first argues for standing "outside" of globalisation and its educational cultures and apparatuses. It…

"Otherways" into the Garden: Re-Visioning the Feminine in "The Secret Garden."

ERIC Educational Resources Information Center

Parsons, Linda T.

2002-01-01

Documents the author's interpretation of Frances Hodgson Burnett's "The Secret Garden." Explores a series of questions dealing with issues such as sight, speech, power, gender construction, and symbolism. Reveals the positive and potent ways women subvert the hegemony of patriarchal society and the celebration of the divine feminine…

Trust Relationships in Schools: Supporting or Subverting Implementation of School-Wide Initiatives

ERIC Educational Resources Information Center

Gregory, Jess L.

2017-01-01

This article explores trust relationships in schools that involve disparities in power. Trust is a key factor in developing a positive school culture and strong leadership in schools. Even with the flattening of hierarchies through more distributive models of leadership, disparities in power exist and they influence the trust relationships in…

Pedagogy of Attention: Subverting the Strong Language of Intention in Social Justice Education

ERIC Educational Resources Information Center

Desroches, Sarah J.

2016-01-01

In this paper, I explore the possibility of social justice education as pedagogy of "attention" rather than simply pedagogy of "intention." Drawing on Gert Biesta's (2010) concept of "strong" education, I begin by explaining how the language of intention in social justice education relies on a discourse in which…

The Lesbian Stigma in the Sport Context: Implications for Women of Every Sexual Orientation

ERIC Educational Resources Information Center

Sartore, Melanie L.; Cunningham, George B.

2009-01-01

The lesbian label exists within sport's heterosexist and heteronormative context as a means to subvert women's status, power, influence, and experiences. As such, there exists a lesbian stigma that contributes to sport's documented gender disparities. While acknowledged that some women may manage their gender and sexual identities to evade…

Welfare's "New Consensus": The Collapse of the American Family.

ERIC Educational Resources Information Center

Gilder, George; And Others

1987-01-01

A national workfare scheme would subvert the foundations of capitalism and family life because the government is incompetent in the area of child care and because the prime role of a mother is raising children not earning money. Religious supports must undergird family values in order to diminish the moral anarchy present today. (VM)

Race, the Black Male, and Heterogeneous Racisms in Education

ERIC Educational Resources Information Center

Johnson-Bailey, Juanita; Ray, Nichole; Lasker-Scott, Tennille

2014-01-01

This chapter explores the effects of historical and current racism on the educational experiences of American Black males. The authors use critical race theory to illustrate how assumptions about culture and gender have subverted the egalitarian ideals of adult education. Teachers and students are urged to use critical reflection and open…

Inflammation and oxidative stress in vertebrate host–parasite systems

PubMed Central

Sorci, Gabriele; Faivre, Bruno

2008-01-01

Innate, inflammation-based immunity is the first line of vertebrate defence against micro-organisms. Inflammation relies on a number of cellular and molecular effectors that can strike invading pathogens very shortly after the encounter between inflammatory cells and the intruder, but in a non-specific way. Owing to this non-specific response, inflammation can generate substantial costs for the host if the inflammatory response, and the associated oxygen-based damage, get out of control. This imposes strong selection pressure that acts to optimize two key features of the inflammatory response: the timing of activation and resolution (the process of downregulation of the response). In this paper, we review the benefits and costs of inflammation-driven immunity. Our aim is to emphasize the importance of resolution of inflammation as a way of maintaining homeostasis against oxidative stress and to prevent the ‘horror autotoxicus’ of chronic inflammation. Nevertheless, host immune regulation also opens the way to pathogens to subvert host defences. Therefore, quantifying inflammatory costs requires assessing (i) short-term negative effects, (ii) delayed inflammation-driven diseases, and (iii) parasitic strategies to subvert inflammation. PMID:18930878

Molecular mimicry: an important virulence strategy employed by Legionella pneumophila to subvert host functions.

PubMed

Nora, Tamara; Lomma, Mariella; Gomez-Valero, Laura; Buchrieser, Carmen

2009-08-01

It is 32 years since Legionella pneumophila was identified and recognized as a human pathogen, causing the severe form of pneumonia termed Legionnaires' disease, or legionellosis. This bacterium is found in freshwater reservoirs where it replicates in aquatic protozoa and can invade man-made water distribution systems. Although the disease can be treated by antibiotherapy and prevented through surveillance and control measures, reported cases of Legionnaires' disease continue to rise across Europe and outbreaks of major public health significance still occur. Genome sequencing and analyses led to a giant step forward by suggesting new ways by which this intracellular bacterium might subvert host functions. One particular feature revealed was the presence of many eukaryotic-like proteins, possibly mimicking host proteins to allow intracellular replication of Legionella. Here, we describe the identification and analysis of these proteins and report on recent advances detailing the mechanisms by which these proteins function. Finally, comparative and evolutionary genomic aspects regarding the eukaryotic-like proteins are presented. Collectively, these data have shed new light on the virulence strategies of L. pneumophila, a major aspect of which is molecular mimicry.

Disease-Causing Mutations in the G Protein Gαs Subvert the Roles of GDP and GTP.

PubMed

Hu, Qi; Shokat, Kevan M

2018-05-17

The single most frequent cancer-causing mutation across all heterotrimeric G proteins is R201C in Gαs. The current model explaining the gain-of-function activity of the R201 mutations is through the loss of GTPase activity and resulting inability to switch off to the GDP state. Here, we find that the R201C mutation can bypass the need for GTP binding by directly activating GDP-bound Gαs through stabilization of an intramolecular hydrogen bond network. Having found that a gain-of-function mutation can convert GDP into an activator, we postulated that a reciprocal mutation might disrupt the normal role of GTP. Indeed, we found R228C, a loss-of-function mutation in Gαs that causes pseudohypoparathyroidism type 1a (PHP-Ia), compromised the adenylyl cyclase-activating activity of Gαs bound to a non-hydrolyzable GTP analog. These findings show that disease-causing mutations in Gαs can subvert the canonical roles of GDP and GTP, providing new insights into the regulation mechanism of G proteins. Copyright © 2018 Elsevier Inc. All rights reserved.

Kinematic analysis of asymmetric folds in competent layers using mathematical modelling

NASA Astrophysics Data System (ADS)

Aller, J.; Bobillo-Ares, N. C.; Bastida, F.; Lisle, R. J.; Menéndez, C. O.

2010-08-01

Mathematical 2D modelling of asymmetric folds is carried out by applying a combination of different kinematic folding mechanisms: tangential longitudinal strain, flexural flow and homogeneous deformation. The main source of fold asymmetry is discovered to be due to the superimposition of a general homogeneous deformation on buckle folds that typically produces a migration of the hinge point. Forward modelling is performed mathematically using the software 'FoldModeler', by the superimposition of simple shear or a combination of simple shear and irrotational strain on initial buckle folds. The resulting folds are Ramsay class 1C folds, comparable to those formed by symmetric flattening, but with different length of limbs and layer thickness asymmetry. Inverse modelling is made by fitting the natural fold to a computer-simulated fold. A problem of this modelling is the search for the most appropriate homogeneous deformation to be superimposed on the initial fold. A comparative analysis of the irrotational and rotational deformations is made in order to find the deformation which best simulates the shapes and attitudes of natural folds. Modelling of recumbent folds suggests that optimal conditions for their development are: a) buckling in a simple shear regime with a sub-horizontal shear direction and layering gently dipping towards this direction; b) kinematic amplification due to superimposition of a combination of simple shear and irrotational strain with a sub-vertical maximum shortening direction for the latter component. The modelling shows that the amount of homogeneous strain necessary for the development of recumbent folds is much less when an irrotational strain component is superimposed at this stage that when the superimposed strain is only simple shear. In nature, the amount of the irrotational strain component probably increases during the development of the fold as a consequence of the increasing influence of the gravity due to the tectonic superimposition of rocks.

Assessment of the microbial community in a constructed wetland that receives acid coal mine drainage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nicomrat, D.; Dick, W.A.; Tuovinen, O.H.

2006-01-15

Constructed wetlands are used to treat acid drainage from surface or underground coal mines. However, little is known about the microbial communities in the receiving wetland cells. The purpose of this work was to characterize the microbial population present in a wetland that was receiving acid coal mine drainage (AMD). Samples were collected from the oxic sediment zone of a constructed wetland cell in southeastern Ohio that was treating acid drainage from an underground coal mine seep. Samples comprised Fe(Ill) precipitates and were pretreated with ammonium oxalate to remove interfering iron, and the DNA was extracted and purified by agarosemore » gel electrophoresis prior to amplification of portions of the 16S rRNA gene. Amplified products were separated by denaturing gradient gel electrophoresis and DNA from seven distinct bands was excised from the gel and sequenced. The sequences were matched to sequences in the GenBank bacterial 16S rDNA database. The DNA in two of the bands yielded matches with Acidithiobacillus ferrooxidans and the DNA in each of the remaining five bands was consistent with one of the following microorganisms: Acidithiobacillus thiooxidans, strain TRA3-20 (a eubacterium), strain BEN-4 (an arsenite-oxidizing bacterium), an Alcaligenes sp., and a Bordetella sp. Low bacterial diversity in these samples reflects the highly inorganic nature of the oxic sediment layer where high abundance of iron- and sulfur-oxidizing bacteria would be expected. The results we obtained by molecular methods supported our findings, obtained using culture methods, that the dominant microbial species in an acid receiving, oxic wetland are A. thiooxidans and A. ferrooxidans.« less

Investigations of ash fouling with cattle wastes as reburn fuel in a small-scale boiler burner under transient conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hyukjin Oh; Kalyan Annamalai; John M. Sweeten

2008-04-15

Fouling behavior under reburn conditions was investigated with cattle wastes (termed as feedlot biomass, FB) and coal as reburn fuels under a transient condition and short-time operation. A small-scale (30 kW or 100,000 Btu/hr) boiler burner research facility was used for the reburn experiments. The fuels considered for these experiments were natural gas (NG) for the ashless case, pure coal, pure FB, and blends of coal and FB. Two parameters that were used to characterize the ash 'fouling' were (1) the overall heat-transfer coefficient (OHTC) when burning NG and solid fuels as reburn fuels, and (2) the combustible loss throughmore » ash deposited on the surfaces of heat exchanger tubes and the bottom ash in the ash port. A new methodology is presented for determining ash fouling behavior under transient conditions. Results on the OHTCs for solid reburn fuels are compared with the OHTCs for NG. It was found that the growth of the layer of ash depositions over longer periods typically lowers OHTC, and the increased concentration of ash in gas phase promotes radiation in high-temperature zones during initial periods while decreasing the heat transfer in low-temperature zones. The ash analyses indicated that the bottom ash in the ash port contained a smaller percentage of combustibles with a higher FB percentage in the fuels, indicating better performance compared with coal because small particles in FB burn faster and the FB has higher volatile matter on a dry ash-free basis promoting more burn out. 16 refs., 12 figs., 6 tabs.« less

The Phrase of the Phallic Pheminine: Beyond the "Nurturing Mother" in Feminist Composition Pedagogy.

ERIC Educational Resources Information Center

Mowery, Diane

Theories of phallic authority outlined by Jaques Lacan, Sigmund Freud, and Luce Irigaray suggest that one can effectively undo authority only from a position of authority, a position that traps feminists within the very phallic economy they hope to subvert. Attempting to avoid this trap, feminist pedagogues have made a distinction between…

"Old People Are Useless:" Representations of Aging on "The Simpsons"

ERIC Educational Resources Information Center

Blakeborough, Darren

2008-01-01

This article looks at how "The Simpsons'" representations of aging, considered ageist and stereotypical by some, can be viewed as a positive look at the elderly that attempts to subvert the same stereotypes that it seemingly employs. The Baby Boom cohort is now seen as an attractive economic group, and as they continue their journey through the…

Theatre across Prison Walls: Using Democratizing Theatre Methodologies to Subvert Carceral Control

ERIC Educational Resources Information Center

Rocchio, Rivka

2017-01-01

In spite of the influx of articles on practitioner experience teaching in carceral settings, little has been written around the methodologies that best level the inherent inequity between practitioner and ensemble. This article seeks to respond to some of the questions and concerns around the balancing of power structures by describing the…

A Critique of Contemporary Approaches to the Study of Political Communication.

ERIC Educational Resources Information Center

Sanders, Keith R.

The twentieth century history of the academic study of political communication can be divided into three parts: the period between the World Wars, the period 1940-1965, and the period from 1965 to the present. In the first period, social scientists were greatly concerned that the democratic process might be subverted by propaganda; they were…

Scieszka's "The Stinky Cheese Man": A Tossed Salad of Parodic Re-Versions

ERIC Educational Resources Information Center

Pantaleo, Sylvia

2007-01-01

"The Stinky Cheese Man and Other Fairly Stupid Tales" (1992) by Jon Scieszka and Lane Smith was awarded a Randolph Caldecott Honor Medal in 1993. Scieszka and Smith subvert textual authority through playing "with literary and cultural codes and conventions" (McCallum 1996, p. 400) in their metafictive text. In this article, I discuss the…

Poetry in Motion: In Search of the Poetic in Health and Physical Education

ERIC Educational Resources Information Center

Fitzpatrick, Katie

2018-01-01

This article uses poetry to show how we might reimagine the body and movement in ways that speak back to and subvert dominant and neoliberal conceptions of health and physical education (HPE). Drawing on the notion of poiesis and Arnold's conceptualisation of physical education as "in through and about movement," I explore possibilities…

The Standards Paradox: How Quality Assurance Regimes Can Subvert Teaching and Learning in Higher Education

ERIC Educational Resources Information Center

Brady, Norman; Bates, Agnieszka

2016-01-01

The quest continues to standardise quality assurance systems throughout the European Higher Education Area (EHEA) under the auspices of the Bologna Process and led by the European Network for Quality Assurance (ENQA). Mirroring its member organisation in England, the Quality Assurance Agency (QAA), ENQA identifies, as one of its core aims, the…

Rationality in the Academy: Why Responsibility Center Budgeting Is a Wrong Step Down the Wrong Road.

ERIC Educational Resources Information Center

Adams, E. M.

1997-01-01

Responsibility Center Budgeting/Management in higher education places at the heart of the university a mode of rationality in decision making that subverts educational policy and weakens the institution's ability for corrective cultural criticism. Academic leaders should make academic and research decisions based on students' and society's…

Struggles to Subvert the Gendered Field: Issues of Masculinity, Rurality and Class

ERIC Educational Resources Information Center

Keddie, Amanda; Mills, Carmen; Mills, Martin

2008-01-01

This article explores the complex struggles associated with intersections of class, rurality and masculinity, and the ways in which such intersections work to preserve a gendered status quo within and beyond school communities in Australia. Drawing on the stories of Monica and Phoebe, two teachers who understand schooling as a site of…

Siren call of metaphor: subverting the proper task of neuroscience.

PubMed

Werner, Gerhard

2004-09-01

Under the assumption that nervous systems form a distinct category among the objects in Nature, applying metaphors of psychological and behavioral science disciplines is flawed and invites confusion. Moreover, such practices obscure and detract from the primary task of Neurophysiology: to investigate the intrinsic properties of nervous systems, uncontaminated with concepts borrowed from other disciplines.

Discourses of Education and Constitutions of Class: Public Discourses on Education in Swedish PBS Television

ERIC Educational Resources Information Center

Reimers, Eva

2014-01-01

Drawing on post-structural perspectives and analysis of television programs on education, the article investigates the public educational discourse in Sweden. It shows how a dominant neoliberal educational discourse is articulated together with a discourse of equal education, where the two discourses influence and subvert each other so that…

Discursive Contestations and Pluriversal Futures: A Decolonial Analysis of Educational Policies in the United Arab Emirates

ERIC Educational Resources Information Center

Aydarova, Elena

2017-01-01

Most research on global transformations in education has focused on the actions of political and economic elites. As a result, attempts to contest and subvert globally circulated policies at subnational levels have received less attention. To address this gap, this study focuses on discursive contestations around educational reforms in the United…

'Dual hit' metabolic modulator LDCA selectively kills cancer cells by efficient competitive inhibition of LDH-A.

PubMed

Ghosh, Monisankar; Saha, Suchandrima; Dutta, Samir Kumar

2016-02-07

Herein, we synthesize and elucidate the potential of a novel 'dual hit' molecule, LDCA, to constitutively block lactate dehydrogenase isoform-A (LDH-A) to selectively subvert apoptosis and rigorously attenuate breast tumor progression in a mouse model, comprehensively delineating the therapeutic prospectus of LDCA in the field of cancer metabolics.

Scientific rigor through videogames.

PubMed

Treuille, Adrien; Das, Rhiju

2014-11-01

Hypothesis-driven experimentation - the scientific method - can be subverted by fraud, irreproducibility, and lack of rigorous predictive tests. A robust solution to these problems may be the 'massive open laboratory' model, recently embodied in the internet-scale videogame EteRNA. Deploying similar platforms throughout biology could enforce the scientific method more broadly. Copyright © 2014 Elsevier Ltd. All rights reserved.

Least Square Fast Learning Network for modeling the combustion efficiency of a 300WM coal-fired boiler.

PubMed

Li, Guoqiang; Niu, Peifeng; Wang, Huaibao; Liu, Yongchao

2014-03-01

This paper presents a novel artificial neural network with a very fast learning speed, all of whose weights and biases are determined by the twice Least Square method, so it is called Least Square Fast Learning Network (LSFLN). In addition, there is another difference from conventional neural networks, which is that the output neurons of LSFLN not only receive the information from the hidden layer neurons, but also receive the external information itself directly from the input neurons. In order to test the validity of LSFLN, it is applied to 6 classical regression applications, and also employed to build the functional relation between the combustion efficiency and operating parameters of a 300WM coal-fired boiler. Experimental results show that, compared with other methods, LSFLN with very less hidden neurons could achieve much better regression precision and generalization ability at a much faster learning speed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Global spatial indexing of the human impact on Al, Cu, Fe, and Zn mobilization.

PubMed

Rauch, Jason N

2010-08-01

With increasing consumption of material by human activity, the extent of human influence relative to nature in the mobilization of metals and other elements on Earth continues to grow. Recognizing people as modern geomorphic agents, I produced global data layers at 1 degreesx1 degrees of human-mediated mass flows (coal combustion, biomass burning, and mining) and nature-mediated mass flows (net primary productivity, sea salt aerosol emission, and denudation to the oceans) for the industrial metals of aluminum, iron, copper, and zinc for the year 2000. The major mobilization processes are denudation (natural) and mining (anthropic), though net primary productivity for Zn and Cu and coal combustion for Al are nearly as significant. All flows are subsequently combined into an index representing human versus nature flow dominance. As the first maps of mobilization flows of metals widely used by modern technology, they reveal that approximately 1-5% (depending upon the metal) of Earth's land surface now has metal flow dominated by human activity.

Rehabilitating asphalt highways

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butalia, T.S.

2007-07-01

Coal fly ash has been used on two Ohio full-depth reclamation projects in Delaware and Warren. The object of the project carried out with the Department of Civil and Environmental Engineering and Geodetic Science at Ohio State University is to demonstrate the effective use of Class fly ash in combination with lime or lime kiln dust in the full depth reclamation of asphalt pavements. The article describes the mixes used for the highway reconstruction of part of Section Line Road Delaware County and of a road in Warren County. During construction the pavement sections were instrumented with several structural andmore » environmental monitoring devices and data is being collected on a quarterly basis. Falling Weight Deflectometer (FWD) tests to measure load defection behaviour, resilient of pavement layers and soil and base structural layer coefficient are being carried out twice a year. It was shown that use of fly ash increased the elastic modulus of base layers. This article first appeared in the Feb/May 2007 issue of Asphalt Contractor. 4 photos.« less

Cyborgization: Deaf Education for Young Children in the Cochlear Implantation Era

ERIC Educational Resources Information Center

Valente, Joseph Michael

2011-01-01

The author, who was raised oral deaf himself, recounts a visit to a school for young deaf children and discovers that young d/Deaf children and their rights are subverted by the cochlear implantation empire. The hypercapitalist, techno-manic times of cochlear implantation has wreaked havoc to the lives of not only young children with deafness but…

Muted Rhetors and the Mundane: The Case of Ruth Mary Weeks, Rewey Belle Inglis, and W. Wilbur Hatfield

ERIC Educational Resources Information Center

Bordelon, Suzanne

2012-01-01

This essay reveals the importance of investigating mundane internal documents, particularly when considering muted rhetors, who may use such texts strategically in an attempt to subvert the status quo. It does so by examining the first and second women presidents of NCTE and their efforts to professionalize the organization and to strengthen the…

The Single European Act for 1992 and U.S. Television Programming.

ERIC Educational Resources Information Center

Noor Al-Deen, Hana S.

Global exports of television programs have been dominated by U.S. companies. Most of their exports are sold to Western European countries. Such a large influx of imports brings with it cultural values that can subvert the indigenous culture and may lead to cultural hegemony. To reach some balance with the United States in the cultural/media…

Moral Responsibility, Authenticity, and Education. Routledge International Studies in the Philosophy of Education

ERIC Educational Resources Information Center

Haji, Ishtiyaque; Cuypers, Stefaan E.

2012-01-01

The primary purpose of this book is to explain the distinction, on the one hand, between indoctrination and education, and, on the other, between responsibility-subverting manipulation and mere causation. Both are elucidated by an appeal to common ground, an account of when our motivations and other springs of action are "truly our own" or…

Academic Staff Views of Quality Systems for Teaching and Learning: A Hong Kong Case Study

ERIC Educational Resources Information Center

Jones, John; Saram, Don Darshi De

2005-01-01

The "Teaching and Learning Quality Process Review" (TLQPR) recently completed in Hong Kong had an emphasis on education quality work. This paper analyses how, from the perspective of academic staff in one university in Hong Kong, the good intentions embedded in that idea are enhanced or subverted by the broader ?quality system setting in…

Breaking Monotony: A Reflective Study of Teaching Decorative Pot Making

ERIC Educational Resources Information Center

Nortey, Samuel; Okai, Frederick E.; Bodjawah, Edwin K.

2013-01-01

In art, the idea of pots being circular and cylindrical is an intuitive proposition that defines why potters have, up to the present, made wonderful decorations in the round. It is believed that potters do not want to subvert or break away from their tradition, perhaps because the art started as family craft. In this study, the authors describe…

Backyard Brats and Eastside Punks: A History of East LA's Punk Scene

ERIC Educational Resources Information Center

Alvarado, Jimmy

2012-01-01

Music history and punk rock have long had an uneasy relationship because historians often fail to take two major factors into account when approaching the subject matter. One: punk's raison d'etre is to subvert much that music historians rely on in order to deem a particular performer or group significant. And two: punk is a living, thriving…

A Response to Annette Gough and Jesse Bazzul. Subverting Subjectivity: An Anti-Neoliberal Reformulation of Science Education for Life

ERIC Educational Resources Information Center

Levinson, Ralph

2017-01-01

In responding to Jesse Bazzul's and Annette Gough's articles I maintain that contemporary positivist science curricula cannot address the urgent issues of sustainability and biopower that confront us. Drawing on the writings and interpretations of Emmanuel Levinas I argue that contemplating the meaning of responsibility to the Other is a radically…

Shrapnel: Latency, Mourning and the Suicide of a Parent

ERIC Educational Resources Information Center

Bisagni, Francesco

2012-01-01

The aim of this paper is to describe some acute responses to the suicide of a parent, through the account of the analytic psychotherapy of a latency child who found the body of his dead father. The acute traumatic responses of the child show that the perceptual apparatus, time and space are subverted, while the functioning of the contact barrier…

Back Translation: An Emerging Sophisticated Cyber Strategy to Subvert Advances in "Digital Age" Plagiarism Detection and Prevention

ERIC Educational Resources Information Center

Jones, Michael; Sheridan, Lynnaire

2015-01-01

Advances have been made in detecting and deterring the student plagiarism that has accompanied the uptake and development of the internet. Many authors from the late 1990s onwards grappled with plagiarism in the digital age, presenting articles that were provoking and established the foundation for strategies to address cyber plagiarism, including…

Teacher Professionalism: Subverting the Society of Control

ERIC Educational Resources Information Center

Wood, Phil

2014-01-01

The past 30 years have seen a series of major shifts in English education. Central to these changes has been the growth of data systems which now measure and control the work of teachers to a huge degree. This form of data-led surveillance was predicted in the work of Gilles Deleuze, a totalising process where data become more important than the…

The Dialogue of the Host-Parasite Relationship: Leishmania spp. and Trypanosoma cruzi Infection.

PubMed

de Morais, Carlos Gustavo Vieira; Castro Lima, Ana Karina; Terra, Rodrigo; dos Santos, Rosiane Freire; Da-Silva, Silvia Amaral Gonçalves; Dutra, Patrícia Maria Lourenço

2015-01-01

The intracellular protozoa Leishmania spp. and Trypanosoma cruzi and the causative agents of Leishmaniasis and Chagas disease, respectively, belong to the Trypanosomatidae family. Together, these two neglected tropical diseases affect approximately 25 million people worldwide. Whether the host can control the infection or develops disease depends on the complex interaction between parasite and host. Parasite surface and secreted molecules are involved in triggering specific signaling pathways essential for parasite entry and intracellular survival. The recognition of the parasite antigens by host immune cells generates a specific immune response. Leishmania spp. and T. cruzi have a multifaceted repertoire of strategies to evade or subvert the immune system by interfering with a range of signal transduction pathways in host cells, which causes the inhibition of the protective response and contributes to their persistence in the host. The current therapeutic strategies in leishmaniasis and trypanosomiasis are very limited. Efficacy is variable, toxicity is high, and the emergence of resistance is increasingly common. In this review, we discuss the molecular basis of the host-parasite interaction of Leishmania and Trypanosoma cruzi infection and their mechanisms of subverting the immune response and how this knowledge can be used as a tool for the development of new drugs.

A seismological overview of the induced earthquakes in the Duvernay play near Fox Creek, Alberta

NASA Astrophysics Data System (ADS)

Schultz, Ryan; Wang, Ruijia; Gu, Yu Jeffrey; Haug, Kristine; Atkinson, Gail

2017-01-01

This paper summarizes the current state of understanding regarding the induced seismicity in connection with hydraulic fracturing operations targeting the Duvernay Formation in central Alberta, near the town of Fox Creek. We demonstrate that earthquakes in this region cluster into distinct sequences in time, space, and focal mechanism using (i) cross-correlation detection methods to delineate transient temporal relationships, (ii) double-difference relocations to confirm spatial clustering, and (iii) moment tensor solutions to assess fault motion consistency. The spatiotemporal clustering of the earthquake sequences is strongly related to the nearby hydraulic fracturing operations. In addition, we identify a preference for strike-slip motions on subvertical faults with an approximate 45° P axis orientation, consistent with expectation from the ambient stress field. The hypocentral geometries for two of the largest-magnitude (M 4) sequences that are robustly constrained by local array data provide compelling evidence for planar features starting at Duvernay Formation depths and extending into the shallow Precambrian basement. We interpret these lineaments as subvertical faults orientated approximately north-south, consistent with the regional moment tensor solutions. Finally, we conclude that the sequences were triggered by pore pressure increases in response to hydraulic fracturing stimulations along previously existing faults.

A Comprehensive Overview of the Duvernay Induced Seismicity near Fox Creek, Alberta

NASA Astrophysics Data System (ADS)

Schultz, R.; Wang, R.; Gu, Y. J.; Haug, K.; Atkinson, G. M.

2016-12-01

In this work we summarize the current state of understanding regarding the induced seismicity related to Duvernay hydraulic fracturing operations in central Alberta, near the town of Fox Creek. Earthquakes in this region cluster into distinct sequences in time, space, and focal mechanism. To corroborate this point, we use cross-correlation detection methods to delineate transient temporal relationships, double-difference relocations to confirm spatial clustering, and moment tensor determinations to show fault motion consistency. The spatiotemporal clustering of sequences is strongly related to nearby hydraulic fracturing operations. In addition, we identify a strong preference for subvertical strike-slip motion with a roughly 45º P-axis orientation, consistent with ambient stress field considerations. The hypocentral geometry in two red traffic light protocol cases, that are robustly constrained by local array data, provide compelling evidence for planar features starting at Duvernay Formation depths and extending into the shallow Precambrian basement. We interpret these features as faults orientated approximately north-south and subvertically, consistent with moment tensor determinations. Finally, we conclude that the primary sequences are best explained as induced events in response to effective stress changes as a result of pore-pressure increase along previously existing faults due to hydraulic fracturing stimulations.

Identifying Mechanisms by Which Escherichia coli O157:H7 Subverts Interferon-γ Mediated Signal Transducer and Activator of Transcription-1 Activation

PubMed Central

Ho, Nathan K.; Crandall, Ian; Sherman, Philip M.

2012-01-01

Enterohemorrhagic Escherichia coli serotype O157:H7 is a food borne enteric bacterial pathogen that causes significant morbidity and mortality in both developing and industrialized nations. E. coli O157:H7 infection of host epithelial cells inhibits the interferon gamma pro-inflammatory signaling pathway, which is important for host defense against microbial pathogens, through the inhibition of Stat-1 tyrosine phosphorylation. The aim of this study was to determine which bacterial factors are involved in the inhibition of Stat-1 tyrosine phosphorylation. Human epithelial cells were challenged with either live bacteria or bacterial-derived culture supernatants, stimulated with interferon-gamma, and epithelial cell protein extracts were then analyzed by immunoblotting. The results show that Stat-1 tyrosine phosphorylation was inhibited by E. coli O157:H7 secreted proteins. Using sequential anion exchange and size exclusion chromatography, YodA was identified, but not confirmed to mediate subversion of the Stat-1 signaling pathway using isogenic mutants. We conclude that E. coli O157:H7 subverts Stat-1 tyrosine phosphorylation in response to interferon-gamma through a still as yet unidentified secreted bacterial protein. PMID:22253910

Investigating seismic anisotropy beneath the Reykjanes Ridge using models of mantle flow, crystallographic evolution, and surface wave propagation

NASA Astrophysics Data System (ADS)

Gallego, A.; Ito, G.; Dunn, R. A.

2013-08-01

Surface wave studies of the Reykjanes Ridge (RR) and the Iceland hotspot have imaged an unusual and enigmatic pattern of two zones of negative radial anisotropy on each side of the RR. We test previously posed and new hypotheses for the origin of this anisotropy, by considering lattice preferred orientation (LPO) of olivine A-type fabric in simple models with 1-D, layered structures, as well as in 2-D and 3-D geodynamic models with mantle flow and LPO evolution. Synthetic phase velocities of Love and Rayleigh waves traveling parallel to the ridge axis are produced and then inverted to mimic the previous seismic studies. Results of 1-D models show that strong negative radial anisotropy can be produced when olivine a axes are preferentially aligned not only vertically but also subhorizontally in the plane of wave propagation. Geodynamic models show that negative anisotropy on the sides of the RR can occur when plate spreading impels a corner flow, and in turn a subvertical alignment of olivine a axes, on the sides of the ridge axis. Mantle dehydration must be invoked to form a viscous upper layer that minimizes the disturbance of the corner flow by the Iceland mantle plume. While the results are promising, important discrepancies still exist between the observed seismic structure and the predictions of this model, as well as models of a variety of types of mantle flow associated with plume-ridge interaction. Thus, other factors that influence seismic anisotropy, but not considered in this study, such as power-law rheology, water, melt, or time-dependent mantle flow, are probably important beneath the Reykjanes Ridge.

Amphibolite boudins in marble on Naxos, Greece: 3D analysis of multiphase deformation on a retrograde P-T path

NASA Astrophysics Data System (ADS)

Virgo, Simon; von Hagke, Christoph; Urai, Janos L.

2017-04-01

Boudins are periodic structures that form by layer parallel extension in mechanically layered rocks. The characteristics of boudins such as orientation and geometry provide constraints on the paleo stress field as well as the rheology of the rocks during deformation. However, most characterizations of boudinage are based on 2D observations and do not consider the 3-dimensional complexity and potentially non-coaxial polyphase genesis of boudinage structures. In marble quarries in the high grade complex on Naxos, Greece, we studied spectacular outcrops of amphibolite and pegmatite boudins, in combination with serial slicing of quarried blocks to reconstruct the 3D boudin structures. We identified five boudin generations with two distinct generations of early, high grade pinch-and-swell followed by two generations of brittle shearband and torn boudins formed along the retrograde path under greenschist facies conditions. The five generations of boudinage indicate that E-W compression is the main mode of deformation in the marbles. The axis of extension changes from subvertical during pinch-and swell deformation to subhorizontal N-S extension at later stages of deformation. Later phases of boudinage are influenced by existing boudin geometries, producing complex structures in 3D. In 2D section the complexity is not directly apparent and reveals itself only after statistical analysis of long continuous sections. Apart from implications for the regional geology, our findings highlight the importance of 3D characterization of boudinage structures for boudin classification. The insights we gain from the analysis of multiphase boudinage structures on Naxos are the basis for quantitative boudin analysis to infer rheology, effective stress, vorticity and strain, and establish a boudin classification scheme with appeal to a complete mechanics.

Dissolved noble gases and stable isotopes as tracers of preferential fluid flow along faults in the Lower Rhine Embayment, Germany

NASA Astrophysics Data System (ADS)

Gumm, L. P.; Bense, V. F.; Dennis, P. F.; Hiscock, K. M.; Cremer, N.; Simon, S.

2016-02-01

Groundwater in shallow unconsolidated sedimentary aquifers close to the Bornheim fault in the Lower Rhine Embayment (LRE), Germany, has relatively low δ2H and δ18O values in comparison to regional modern groundwater recharge, and 4He concentrations up to 1.7 × 10-4 cm3 (STP) g-1 ± 2.2 % which is approximately four orders of magnitude higher than expected due to solubility equilibrium with the atmosphere. Groundwater age dating based on estimated in situ production and terrigenic flux of helium provides a groundwater residence time of ˜107 years. Although fluid exchange between the deep basal aquifer system and the upper aquifer layers is generally impeded by confining clay layers and lignite, this study's geochemical data suggest, for the first time, that deep circulating fluids penetrate shallow aquifers in the locality of fault zones, implying that sub-vertical fluid flow occurs along faults in the LRE. However, large hydraulic-head gradients observed across many faults suggest that they act as barriers to lateral groundwater flow. Therefore, the geochemical data reported here also substantiate a conduit-barrier model of fault-zone hydrogeology in unconsolidated sedimentary deposits, as well as corroborating the concept that faults in unconsolidated aquifer systems can act as loci for hydraulic connectivity between deep and shallow aquifers. The implications of fluid flow along faults in sedimentary basins worldwide are far reaching and of particular concern for carbon capture and storage (CCS) programmes, impacts of deep shale gas recovery for shallow groundwater aquifers, and nuclear waste storage sites where fault zones could act as potential leakage pathways for hazardous fluids.

Human papillomavirus molecular biology and disease association

PubMed Central

Egawa, Nagayasu; Griffin, Heather; Kranjec, Christian; Murakami, Isao

2015-01-01

Summary Human papillomaviruses (HPVs) have evolved over millions of years to propagate themselves in a range of different animal species including humans. Viruses that have co‐evolved slowly in this way typically cause chronic inapparent infections, with virion production in the absence of apparent disease. This is the case for many Beta and Gamma HPV types. The Alpha papillomavirus types have however evolved immunoevasion strategies that allow them to cause persistent visible papillomas. These viruses activate the cell cycle as the infected epithelial cell differentiates in order to create a replication competent environment that allows viral genome amplification and packaging into infectious particles. This is mediated by the viral E6, E7, and E5 proteins. High‐risk E6 and E7 proteins differ from their low‐risk counterparts however in being able to drive cell cycle entry in the upper epithelial layers and also to stimulate cell proliferation in the basal and parabasal layers. Deregulated expression of these cell cycle regulators underlies neoplasia and the eventual progression to cancer in individuals who cannot resolve high‐risk HPV infection. Most work to date has focused on the study of high‐risk HPV types such as HPV 16 and 18, which has led to an understanding of the molecular pathways subverted by these viruses. Such approaches will lead to the development of better strategies for disease treatment, including targeted antivirals and immunotherapeutics. Priorities are now focused toward understanding HPV neoplasias at sites other than the cervix (e.g. tonsils, other transformation zones) and toward understanding the mechanisms by which low‐risk HPV types can sometimes give rise to papillomatosis and under certain situations even cancers. Copyright © 2015 John Wiley & Sons, Ltd. PMID:25752814

Chronostratigraphic and depositional sequences of the Fort Union formation (Paleocene), Williston Basin, North Dakota, South Dakota, and Montana

USGS Publications Warehouse

Warwick, Peter D.; Flores, Romeo M.; Nichols, Douglas J.; Murphy, Edward C.; Pashin, Jack C.; Gastaldo, Robert A.

2004-01-01

The Fort Union Formation in the Williston Basin of North Dakota, South Dakota, and Montana comprises chronostratigraphic and depositional sequences of Paleocene age. Individual chronostratigraphic sequences are defined by palynostratigraphic (pollen and spore) biozones and radiometric (40Ar/39Ar) ages obtained from tonsteins or volcanic ash layers. Analyses of depositional sequences are based on lithofacies constrained by the radiometric ages and biozones.The lower Paleocene (biozones P1-P3) contains three marine parasequences (landward stepping) in southwestern North Dakota that sequentially onlapped westward between 65 and 61 Ma (lower Ludlow and Cannonball Members). Maximum flooding (transgressive systems tract) occurred during an approximate 1-m.y. interval from 65 to 64 Ma, which regionally is correlated biostratigraphically to a tidally influenced, distributary-shoreface, and fluvial-channel complex in the Cave Hills, northwestern South Dakota, and to channel-dominated fluvial (low-stand incised paleovalley systems) and tidally influenced, flood-plain-deltaic transition facies in the Ekalaka area of southeastern Montana.The progradational parasequences in the Cannonball Member consist of shore-face sandstone beds (with ravinement lag deposits) deposited by strand-plain barrier systems. Landward of the barrier systems, tidal-estuarine and mire deposits included thick but laterally discontinuous peat accumulations (e.g., Beta and Yule coal beds in the Ludlow Member, southwestern North Dakota). However, landward of the coastal deposits, the laterally equivalent T-Cross-Big Dirty coal zone (dated 64.78 Ma) in southeastern Montana formed as thick, laterally extensive peat accumulations in mires in a fluvial setting. In the flood-plain-deltaic, tidal transition zone near Ekalaka, Montana, the Ludlow Member consists of flood-plain facies, discontinuous coal beds, and rooted and burrowed horizons that contain the marine or brackish trace fossil Skolithos. The flood-plain-deltaic tidal transition zone facies are incised by a massive, agglomerated channel sandstone complex (paleovalley fill) that is exposed along the modern Snow Creek drainage south of Mill Iron, Montana. The flood-plain-tidal transition zone was reworked during the maximum sea level highstand during the early Paleocene. This event was followed by a fall of sea level and deposition of the paleovalley fill.Sea level fall during the mid-Paleocene (biozones P3 and P4) produced a regressive shallow-marine and lower deltaic tidal system (seaward stepping) that deposited strata that thin toward the east. These strata are overlain by a widespread paleosol (Rhame bed) and, in turn, a lignite-bearing fluvial facies (Tongue River Member) containing the laterally persistent Harmon-Hanson coal zone (61.23 Ma). Upper Paleocene biozone P5 is represented by fluvial, coal-bearing strata that contain several economically minable coal beds (HT Butte, Hagel, and Beulah-Zap zones, Sentinel Butte Member).The Fort Union Formation of the Williston Basin contains significant coal resources. These coal deposits are now being explored for their potential coal-bed gas resources. A better understanding of the depositional setting for these deposits can lead to improved exploration and exploitation practices and a better understanding of regional paleogeography and paleoclimate during the Paleocene.

Gold Nanoclusters@Ru(bpy)₃²⁺-Layered Double Hydroxide Ultrathin Film as a Cathodic Electrochemiluminescence Resonance Energy Transfer Probe.

PubMed

Yu, Yingchang; Lu, Chao; Zhang, Meining

2015-08-04

Herein, it is the first report that a cathodic electrochemiluminescence (ECL) resonance energy transfer (ERET) system is fabricated by layer-by-layer (LBL) electrostatic assembly of CoAl layered double hydroxide (LDH) nanosheets with a mixture of blue BSA-gold nanoclusters (AuNCs) and Ru(bpy)3(2+) (denoted as AuNCs@Ru) on an Au electrode. The possible ECL mechanism indicates that the appearance of CoAl-LDH nanosheets generates a long-range stacking order of the AuNCs@Ru on an Au electrode, facilitating the occurrence of the ERET between BSA-AuNC donors and Ru(bpy)3(2+) acceptors on the as-prepared AuNCs@Ru-LDH ultrathin films (UTFs). Furthermore, it is observed that the cathodic ECL intensity can be quenched efficiently in the presence of 6-mercaptopurine (6-MP) in a linear range of 2.5-100 nM with a detection limit of 1.0 nM. On the basis of these interesting phenomena, a facile cathodic ECL sensor has successfully distinguished 6-MP from other thiol-containing compounds (e.g., cysteine and glutathione) in human serum and urine samples. The proposed sensing scheme opens a way for employing the layered UTFs as a platform for the cathodic ECL of Ru(bpy)3(2+).

From in situ coal to the final coal product: A case study of the Danville Coal Member (Indiana)

USGS Publications Warehouse

Mastalerz, Maria; Padgett, P.L.

1999-01-01

A surface coal mine operation and preparation plant in southwestern Indiana was sampled to examine variations in coal quality and coal petrography parameters for the Danville Coal Member of the Dugger Formation (Pennsylvanian-Desmoinesian, Westphalian D). Representative samples from in situ coal, preparation plant feeds, and a final coal product were collected in order to compare coal quality, coal petrography, trace element concentrations, and ash chemistry of the coal to those of the product. Coal quality parameters of the in situ samples and various feeds, coarse refuse, and final product were variable. The quality of the final coal product was best predicted by the coal quality of the clean coal feed (from the middle portions of the seam). Some trace element contents, especially lead and arsenic, varied between the coal feeds and the product. Lead contents increased in the feeds and product compared to the channel sample of the raw coal, possibly due to contamination in the handling process.A surface coal mine operation and preparation plant in southwestern Indiana was sampled to examine variations in coal quality and coal petrography parameters for the Danville Coal Member of the Dugger Formation (Pennsylvanian-Desmoinesian, Westphalian D). Representative samples from in situ coal, preparation plant feeds, and a final coal product were collected in order to compare coal quality, coal petrography, trace element concentrations, and ash chemistry of the coal to those of the product. Coal quality parameters of the in situ samples and various feeds, coarse refuse, and final product were variable. The quality of the final coal product was best predicted by the coal quality of the clean coal feed (from the middle portions of the seam). Some trace element contents, especially lead and arsenic, varied between the coal feeds and the product. Lead contents increased in the feeds and product compared to the channel sample of the raw coal, possibly due to contamination in the handling process.

Structural expression of a rolling hinge in the footwall of the Brenner Line normal fault, eastern Alps

NASA Astrophysics Data System (ADS)

Axen, Gary J.; Bartley, John M.; Selverstone, Jane

1995-12-01

The kinematic and temporal sequence of structures observed to overprint mylonites along the Brenner Line low-angle normal fault may record passage of the footwall through two rolling hinges, at the top and bottom of a ramp in the shear zone. The structures comprise west down brittle and brittle-ductile structures and east down brittle structures. PT conditions of formation (250° to >400°C and 2-23 km depth), obtained from analysis of oriented fluid inclusion planes, indicate that west down structures were formed at greater depths and temperatures, and therefore earlier, than the east down structures. These data suggest that the brittle structures formed under conditions that permit crystal-plastic deformation at long-term geologic strain rates and therefore probably reflect transient rapid strain rates and/or high fluid pressure. Structures inferred to have formed at a lower hinge are consistent with viscous flow models of rolling-hinge deformation and support the concept of a crustal asthenosphere. Such high temperatures at shallow crustal depth also suggest significant upward advection of heat by extensional unroofing of warm rocks, which may have reduced the flexural rigidity of the footwall and thus affected mechanical behavior at the upper rolling hinge. Exposed mylonitic foliation within a few hundred meters of the Brenner line and on top of the east-west trending anticlines in the footwall dips ˜15° west. Our data favor a ramp dip of ˜25° but permit a dip as great as 45°. Fluid inclusion data suggest that structures related to the hinge at the base of the ramp formed at depths of 12-25 km. If the average dip of the Brenner shear zone to those depths was 20°, intermediate between the favored ramp dip and the dip of exposed foliation, then the horizontal component of slip could be as high as 33-63 km. The two discrete sets of structures with opposite shear senses, formed in the temporal sequence indicated by PT data, are consistent with subvertical simple shear models of rolling-hinge strain. This kinematic pattern is not predicted by the flexural-failure model for rolling hinges. However, the predominance of normal slip at the upper hinge, which extends rather than shortens the mylonitic foliation, fails to match the subvertical simple shear model, which predicts shortening of the foliation there. One possible solution is that superposition of regional extension upon hinge-related stresses modified the rolling-hinge kinematics. Such a modified subvertical shear model can account for the observed small foliation-parallel extensional strains if the foliation was bent <5°-10° passing through the upper hinge. If more bending than that occurred, the data suggest rolling-hinge kinematics in which deformation is achieved by uniform-sense simple shear across the shear zone as in the subvertical simple shear model but in which material lines parallel to the shear-zone foliation and the detachment fault undergo very small length changes, presumably indicating that footwall rocks retained significant resistance to shear and underwent minimal permanent strain. The mechanics that would generate such a rolling hinge are uncertain but may incorporate aspects of both subvertical simple shear and flexural failure. An important kinematic consequence of such a rolling hinge is that all of the net slip across a normal fault, not only its horizontal component, is converted into horizontal extension. This implies a significantly larger magnitude of crustal extension across dipping normal faults whose footwalls passed through a rolling hinge than for those that did not develop along with a hinge.

Multiple Hfq-Crc target sites are required to impose catabolite repression on (methyl)phenol metabolism in Pseudomonas putida CF600.

PubMed

Wirebrand, Lisa; Madhushani, Anjana W K; Irie, Yasuhiko; Shingler, Victoria

2018-01-01

The dmp-system encoded on the IncP-2 pVI150 plasmid of Pseudomonas putida CF600 confers the ability to assimilate (methyl)phenols. Regulation of the dmp-genes is subject to sophisticated control, which includes global regulatory input to subvert expression of the pathway in the presence of preferred carbon sources. Previously we have shown that in P. putida, translational inhibition exerted by the carbon repression control protein Crc operates hand-in-hand with the RNA chaperon protein Hfq to reduce translation of the DmpR regulator of the Dmp-pathway. Here, we show that Crc and Hfq co-target four additional sites to form riboprotein complexes within the proximity of the translational initiation sites of genes encoding the first two steps of the Dmp-pathway to mediate two-layered control in the face of selection of preferred substrates. Furthermore, we present evidence that Crc plays a hitherto unsuspected role in maintaining the pVI150 plasmid within a bacterial population, which has implications for (methyl)phenol degradation and a wide variety of other physiological processes encoded by the IncP-2 group of Pseudomonas-specific mega-plasmids. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

Role of the Mce1 transporter in the lipid homeostasis of Mycobacterium tuberculosis.

PubMed

Forrellad, Marina Andrea; McNeil, Michael; Santangelo, María de la Paz; Blanco, Federico Carlos; García, Elizabeth; Klepp, Laura Inés; Huff, Jason; Niederweis, Michael; Jackson, Mary; Bigi, Fabiana

2014-03-01

Tuberculosis is one of the leading causes of mortality throughout the world. Mycobacterium tuberculosis, the causative agent of human tuberculosis, has developed several strategies involving proteins and other compounds known collectively as virulence factors to subvert human host defences and invade the human host. The Mce proteins are among these virulence-related proteins and are encoded by the mce1, mce2, mce3 and mce4 operons in the genome of M. tuberculosis. It has been proposed that these operons encode ABC-like lipid transporters; however, the nature of their substrates has only been revealed in the case of the Mce4 proteins. Here we found that the knockout of the mce1 operon alters the lipid profile of M. tuberculosis H37Rv and the uptake of palmitic acid. Thin layer chromatography and liquid chromatography-mass spectrometry analysis showed that the mce1 mutant accumulates more mycolic acids than the wild type and complemented strains. Interestingly, this accumulation of mycolic acid is exacerbated when bacteria are cultured in the presence of palmitic acid or arachidonic acid. These results suggest that the mce1 operon may serve as a mycolic acid re-importer. Copyright © 2013 Elsevier Ltd. All rights reserved.

Kinematics of the Neogene Terror Rift: Constraints from calcite twinning strain in AND-1B core, McMurdo Ice Shelf

NASA Astrophysics Data System (ADS)

Paulsen, T.; Wilson, T. J.; Demosthenous, C.; Millan, C.; Jarrard, R. D.; Laufer, A.

2013-12-01

Strain analyses of mechanically twinned calcite in veins and faults hosted by Neogene (13.6 Ma to 4.3 Ma) sedimentary and volcanic rocks recovered within the ANDRILL AND-1B drill core from the Terror Rift in the southern Ross Sea, Antarctica, yield prolate and oblate ellipsoids with principal shortening and extension strains ranging from 0.1% to 8.5%. The majority of samples show homogeneous coaxial strain predominantly characterized by subvertical shortening, which we attribute to lithostatic loading in an Andersonian normal faulting stress regime during sedimentary and ice sheet burial of the stratigraphic sequence. The overall paucity of a non-coaxial layer-parallel shortening signal in the AND-1B twin populations suggests that horizontal compressive stresses predicted by Neogene transtensional kinematic models for the rift system have been absent or of insufficient magnitude to cause a widespread noncoaxial strain overprint. Limited numbers of oriented samples yield a possible average ESE extension direction for the rift that is subparallel to other indicators of Neogene extension. The lack of horizontal shortening in the twin data suggests the Neogene Terror Rift system either lacks a strong longitudinal strike-slip component, or that spatial partitioning of strain controls the maximum shortening axes seen in rocks of this age.

Effects of surface coal mining and reclamation on ground water in small watersheds in the Allegheny Plateau, Ohio

USGS Publications Warehouse

Eberle, Michael; Razem, A.C.

1985-01-01

The hydrologic effects of surface coal mining in unlimited areas is difficult to predict, partly because of a lack of adequate data collected before and after mining and reclamation. In order to help provide data to assess the effects of surface mining on the hydrology of small basins in the coal fields of the eastern United States, the U.S. Bureau of Mines sponsored a comprehensive hydrologic study at three sites in the Ohio part of the Eastern Coal Province. These sites are within the unqlaciated part of the Allegheny Plateau, and are representative of similar coal-producing areas in Kentucky, West Virginia, and Pennsylvania. The U.S. Geological Survey was responsible for the ground-water phase of the study. The aquifer system at each watershed consisted of two localized perched aquifers (top and middle) above a deeper, more regional aquifer. The premining top aquifer was destroyed by mining in each case, and was replaced by spoils during reclamation. The spoils formed new top aquifers that were slowly becoming resaturated at the end of the study period. Water levels in the aquifers were about the same after reclamation as before mining, although levels rose in a few places. It appears that the underclay at the base of the new top aquifers at all three sites prevents significant downward leakage from the top aquifers to lower except in places where the layer may have been damaged during mining. Water in the top aquifers is a calcium sulfate type, whereas calcium bicarbonate type water predominated before mining. The median specific conductance of water in the new top aquifers was about 5 times greater than that of the original top aquifers in two of the watersheds, and 1 1/2 times the level of the original top aquifers in the third. Concentrations of dissolved sulfate, iron, and manganese in the top aquifers before mining generally did not exceed U.S. and Ohio Environmental Protection Agency drinking-water limits, but generally exceeded these limits after reclamation. Water-quality changes in the middle aquifers were minor by comparison. Water levels and water quality in the deeper, regional aquifers were unaffected by mining.

Hydrology of an abandoned coal-mining area near McCurtain, Haskell County, Oklahoma

USGS Publications Warehouse

Slack, L.J.

1983-01-01

Water quality was investigated from October 1980 to May 1983 in an area of abandoned coal mines in Haskell county, Oklahoma. Bedrock in the area is shale, siltstone, sandstone, and the McAlester (Stigler) and Hartshorne coals of the McAlester Formation and Hartshorne Sandstone of Pennsylvanian age. The two coal beds, upper and lower Hartshorne, associated with the Hartshorne Sandstone converge or are separated by a few feet or less of bony coal or shale in the McCurtain area. Many small faults cut the Hartshorne coal in all the McCurtain-area mines. The main avenues of water entry to and movement through the bedrock are the exposed bedding-plane openings between layers of sandstone, partings between laminae of shale, fractures and joints developed during folding and faulting laminae of shale, fractures and joints developed during folding and faulting of the brittle rocks, and openings caused by surface mining--the overburden being shattered and broken to form spoil. Water-table conditions exist in bedrock and spoil in the area. Mine pond water is in direct hydraulic connections with water in the spoil piles and the underlying Hartshorne Sandstone. Sulfate is the best indicator of the presence of coal-mine drainage in both surface and ground water in the Oklahoma coal field. Median sulfate concentrations for four sites on Mule Creek ranged from 26 to 260 milligrams per liter. Median sulfate concentrations increased with increased drainage from unreclaimed mined areas. The median sulfate concentration in Mule Creek where it drains the reclaimed area is less than one-third of that at the next site downstream where the stream begins to drain abandoned (unreclaimed) mine lands. Water from Mule Creek predominantly is a sodium sulfate type. Maximum and median values for specific conductance and concentrations of calcium, magnesium, sodium, sulfate, chloride, dissolved solids, and alkalinity increase as Mule Creek flows downstream and drains increasing areas of abandoned (unreclaimed) mining lands. Constituent concentrations in Mule Creek, except those for dissolved solids, iron, manganese, and sulfate, generally do not exceed drinking-water limits. Reclamation likely would result in decreased concentrations of dissolved solids, calcium, magnesium, sodium, sulfate, and alkalinity in Mule Creek in the vicinity of the reclaimed area. Ground water in the area is moderately hard to very hard alkaline water with a median pH of 7.2 to 7.6. It predominately is a sodium sulfate type and, except for dissolved solids, iron manganese, and sulfate, constituent concentrations generally do not exceed drinking-water limits. Ground-water quality would likely be unchanged by reclamation. The quality of water in the two mine ponds is quite similar to that of the shallow ground water in the area. Constituents in water from both ponds generally do not exceed drinking-water limits and the water quality is unlikely to be changed by reclamation in the area.

Study of the properties of flux cored wire of Fe-C-Si-Mn-Cr-Mo-Ni-V-Co system for the strengthening of nodes and parts of equipment used in the mineral mining

NASA Astrophysics Data System (ADS)

Gusev, A. I.; Kozyrev, N. A.; Usoltsev, A. A.; Kryukov, R. E.; Osetkovsky, I. V.

2017-09-01

The effect of the introduction of vanadium and cobalt into the charge of the powder surfacing wire of Fe-C-Si-Mn-Cr-Mo-Ni system is studied. In the laboratory conditions, the samples of flux cored wires were produced. The surfacing made by the prepared wire was produced under the flux AN-26C, on the plates of steel St3 in 6 layers with the help of ASAW-1250 welding tractor. Reduction of carbon content in the deposited layer to 0.19-0.2% with simultaneous change in the content of chromium, nickel, molybdenum and other elements present in it contributes to the enlargement of the martensite needles and the increase in the size of the former austenite grain. The obtained dependences of hardness of the deposited layer and its wear resistance on the mass fraction of elements, included in the composition of powder wires of the proposed system, can be used to predict the hardness of the welded layer and its wear resistance under different operating conditions for mining equipment and coal mining equipment.

Hierarchical Co-based Porous Layered Double Hydroxide Arrays Derived via Alkali Etching for High-performance Supercapacitors

NASA Astrophysics Data System (ADS)

Abushrenta, Nasser; Wu, Xiaochao; Wang, Junnan; Liu, Junfeng; Sun, Xiaoming

2015-08-01

Hierarchical nanoarchitecture and porous structure can both provide advantages for improving the electrochemical performance in energy storage electrodes. Here we report a novel strategy to synthesize new electrode materials, hierarchical Co-based porous layered double hydroxide (PLDH) arrays derived via alkali etching from Co(OH)2@CoAl LDH nanoarrays. This structure not only has the benefits of hierarchical nanoarrays including short ion diffusion path and good charge transport, but also possesses a large contact surface area owing to its porous structure which lead to a high specific capacitance (23.75 F cm-2 or 1734 F g-1 at 5 mA cm-2) and excellent cycling performance (over 85% after 5000 cycles). The enhanced electrode material is a promising candidate for supercapacitors in future application.

Hierarchical Co-based Porous Layered Double Hydroxide Arrays Derived via Alkali Etching for High-performance Supercapacitors

PubMed Central

Abushrenta, Nasser; Wu, Xiaochao; Wang, Junnan; Liu, Junfeng; Sun, Xiaoming

2015-01-01

Hierarchical nanoarchitecture and porous structure can both provide advantages for improving the electrochemical performance in energy storage electrodes. Here we report a novel strategy to synthesize new electrode materials, hierarchical Co-based porous layered double hydroxide (PLDH) arrays derived via alkali etching from Co(OH)2@CoAl LDH nanoarrays. This structure not only has the benefits of hierarchical nanoarrays including short ion diffusion path and good charge transport, but also possesses a large contact surface area owing to its porous structure which lead to a high specific capacitance (23.75 F cm−2 or 1734 F g−1 at 5 mA cm−2) and excellent cycling performance (over 85% after 5000 cycles). The enhanced electrode material is a promising candidate for supercapacitors in future application. PMID:26278334

Heat transfer in gas turbine engines and three-dimensional flows; Proceedings of the Symposium, ASME Winter Annual Meeting, Chicago, IL, Nov. 27-Dec. 2, 1988

NASA Technical Reports Server (NTRS)

Elovic, E. (Editor); O'Brien, J. E. (Editor); Pepper, D. W. (Editor)

1988-01-01

The present conference on heat transfer characteristics of gas turbines and three-dimensional flows discusses velocity-temperature fluctuation correlations at the flow stagnation flow of a circular cylinder in turbulent flow, heat transfer across turbulent boundary layers with pressure gradients, the effect of jet grid turbulence on boundary layer heat transfer, and heat transfer characteristics predictions for discrete-hole film cooling. Also discussed are local heat transfer in internally cooled turbine airfoil leading edges, secondary flows in vane cascades and curved ducts, three-dimensional numerical modeling in gas turbine coal combustor design, numerical and experimental results for tube-fin heat exchanger airflow and heating characteristics, and the computation of external hypersonic three-dimensional flow field and heat transfer characteristics.

Heat transfer in gas turbine engines and three-dimensional flows; Proceedings of the Symposium, ASME Winter Annual Meeting, Chicago, IL, Nov. 27-Dec. 2, 1988

NASA Astrophysics Data System (ADS)

Elovic, E.; O'Brien, J. E.; Pepper, D. W.

The present conference on heat transfer characteristics of gas turbines and three-dimensional flows discusses velocity-temperature fluctuation correlations at the flow stagnation flow of a circular cylinder in turbulent flow, heat transfer across turbulent boundary layers with pressure gradients, the effect of jet grid turbulence on boundary layer heat transfer, and heat transfer characteristics predictions for discrete-hole film cooling. Also discussed are local heat transfer in internally cooled turbine airfoil leading edges, secondary flows in vane cascades and curved ducts, three-dimensional numerical modeling in gas turbine coal combustor design, numerical and experimental results for tube-fin heat exchanger airflow and heating characteristics, and the computation of external hypersonic three-dimensional flow field and heat transfer characteristics.

Experimental and theoretical investigations of mercury adsorption on hematite (1-102) surfaces

NASA Astrophysics Data System (ADS)

Jung, J.; Wilcox, J.; Jew, A. D.; Rupp, E. C.; Brown, G. E.

2013-12-01

Fly ash is a primary byproduct of the coal combustion process. The release of fly ash into the environment and its use in consumer products are public health concerns because of the presence of toxic trace metals and metalloids, such as mercury (Hg), selenium (Se), and arsenic (As), which may exist as components of fly ash, partition onto fly ash as it cools, or is lost to the environment through smoke stacks in a vapor phase. Therefore, it is important to understand the components of fly ash and their interaction with trace metals. In this study, calculations using density functional theory (DFT) were carried out in conjunction with experimental studies to investigate the interaction between Hg and hematite, an important mineral component of fly ash. Our experimental study, designed to simulate Hg sorption in a coal-fired power plant exhaust system, involved exposure of the fine fraction of bituminous coal fly ash (≤ 0.1 μm) to methane combustion flue gas, supplemented with SO2, NOx, HCl, and Hg in a packed-bed reactor. Sorption reaction products were characterized by synchrotron-based x-ray fluorescence mapping (s-XRF), x-ray diffraction (XRD), and extended x-ray absorption fine structure (EXAFS) spectroscopy. Preliminary s-XRF results showed that Hg in the sample is correlated with Fe, S, Cl, Br, and to a lesser extent with Se and As. From the XRD analysis, the dominant mineral phases detected were quartz, iron oxide (hematite), and various sulfate-bearing cements. Based on the experimental results, DFT studies were carried out to investigate the adsorption of Hg on hematite (α-Fe2O3) (1-102) surfaces. The two α-Fe2O3 (1-102) surfaces modeled consisted of two different surface terminations: (1) M2-clean, which corresponds to the oxygen terminated r-cut surface with the first layer of cations removed and no hydroxyl group and (2) M2-OH2-OH which has bihydroxylated top oxygen atoms and a second layer of hydroxylated oxygen atoms. These surface terminations were selected because both surfaces are highly stable in the temperature range of flue gases. All calculations were conducted using the Vienna ab-initio simulation package (VASP). Probable adsorption sites of Hg on the two α-Fe2O3 surface terminations are suggested based on calculated adsorption energies. Additionally, Bader charge analysis was conducted to characterize the oxidation state of both Hg and Fe in the α-Fe2O3 surfaces. The layer spacing of the structure was also calculated in order to compare the surface geometry before and after Hg adsorption. Preliminary results indicate that the binding energy of Hg on the M2-clean surface is -0.102 eV and that mercury donates electrons to the O and Fe atoms in the top layer when it adsorbs onto the surface.

Graphene-oxide-supported CuAl and CoAl layered double hydroxides as enhanced catalysts for carbon-carbon coupling via Ullmann reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmed, Nesreen S.; Surface Chemistry and Catalytic Studies Group, King Abdulaziz University; Menzel, Robert

Two efficient catalyst based on CuAl and CoAl layered double hydroxides (LDHs) supported on graphene oxide (GO) for the carbon-carbon coupling (Classic Ullmann Homocoupling Reaction) are reported. The pure and hybrid materials were synthesised by direct precipitation of the LDH nanoparticles onto GO, followed by a chemical, structural and physical characterisation by electron microscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), surface area measurements and X-ray photoelectron spectroscopy (XPS). The GO-supported and unsupported CuAl-LDH and CoAl-LDH hybrids were tested over the Classic Ullman Homocoupling Reaction of iodobenzene. In the current study CuAl- and CoAl-LDHs have shown excellent yields (91% and 98%,more » respectively) at very short reaction times (25 min). GO provides a light-weight, charge complementary and two-dimensional material that interacts effectively with the 2D LDHs, in turn enhancing the stability of LDH. After 5 re-use cycles, the catalytic activity of the LDH/GO hybrid is up to 2 times higher than for the unsupported LDH. - Graphical abstract: CuAl- and CoAl-LDHs have shown excellent yields (91% and 98%, respectively) at very short reaction times (25 min). GO provides a light-weight, charge complementary, two-dimensional material that interacts effectively with the 2D LDHs, in turn enhancing the stability of LDH. - Highlights: • CuAl LDH/GO and CoAl LDH/GO hybrid materials with different LDH compositions were prepared. • Hybrids were fully characterised and their catalytic efficiency over the Classic Ullman Reaction was studied. • CuAl- and CoAl-LDHs have shown excellent yields (91% and 98%, respectively) in 25 min reaction times. • GO provides a light-weight, charge complementary, two-dimensional material that interacts effectively with the 2D LDHs. • After 5 re-use cycles, the catalytic activity of the LDH/GO hybrid is up to 2 times higher than for the unsupported LDH.« less

Quality of economically extractable coal beds in the Gillette coal field as compared with other Tertiary coal beds in the Powder River basin, Wyoming and Montana

USGS Publications Warehouse

Ellis, Margaret S.

2002-01-01

The Powder River Basin, and specifically the Gillette coal field, contains large quantities of economically extractable coal resources. These coal resources have low total sulfur content and ash yield, and most of the resources are subbituminous in rank. A recent U.S Geological Survey study of economically extractable coal in the Gillette coal field focused on five coal beds, the Wyodak rider, Upper Wyodak, Canyon, Lower Wyodak-Werner, and Gates/Kennedy. This report compares the coal quality of these economically extractable coal beds to coal in the Wyodak-Anderson coal zone in the Powder River Basin and in the Gillette coal field (Flores and others, 1999) and other produced coal in the Gillette coal field (Glass, 2000). The Upper Wyodak, Canyon, and Lower Wyodak/Werner beds are within the Wyodak-Anderson coal zone. Compared with all coal in the Wyodak-Anderson coal zone, both throughout the Powder River Basin and just within the Gillette coal field; the thick, persistent Upper Wyodak coal bed in the Gillette coal field has higher mean gross calorific value (8,569 Btu/lb), lower mean ash yield (5.8 percent), and lower mean total sulfur content (0.46 percent).

Correlation chart of Pennsylvanian rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania showing approximate position of coal beds, coal zones, and key stratigraphic units: Chapter D.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ruppert, Leslie F.; Trippi, Michael H.; Slucher, Ernie R.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

Because of the many names used to identify individual coal beds and coal zones in the historic Appalachian basin coal-mining districts, coal bed designations may differ even more than stratigraphic nomenclature. In eastern Kentucky, northwest of the Pine Mountain thrust fault on the Cumberland overthrust sheet, for example, coal beds or coal zones equivalent to the Lower Elkhorn coal zone (within the Pikeville Formation) are identified also as the Eagle coal zone, Pond Creek coal zone, and Blue Gem coal bed (fig. 1). Southeast of the Pine Mountain thrust fault, yet still in Kentucky, equivalent coals in this same interval are known as the Imboden and Rich Mountain. Moreover, this same interval of coal is identified as the Blue Gem coal in Tennessee, the Imboden coal bed or Campbell Creek or Pond Creek coal zones in Virginia, and the Eagle coal zone in West Virginia.

Pupils Making a Difference: Enhancing the Power of the Student Peer Group to Promote Positive Social, Emotional and Behavioural Outcomes

ERIC Educational Resources Information Center

Cooper, Paul; Jacobs, Barbara

2011-01-01

In this paper, the authors review empirical evidence on the effects of peer groups on social, emotional and behavioural functioning. The paper shows that an understanding of the ways in which peer groups can influence the development of deviance and subvert the positive effects of interventions can be exploited in the promotion of positive social…

78 FR 28242 - Proposed Information Collection; Cleanup Program for Accumulations of Coal and Float Coal Dusts...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-14

... Program for Accumulations of Coal and Float Coal Dusts, Loose Coal, and Other Combustibles AGENCY: Mine... collection for developing and updating a cleanup program for accumulations of coal and float coal dusts, loose coal, and other combustibles in underground coal mines. DATES: All comments must be postmarked or...

Effects of calcium in ash on the corrosion performance of Ni-based alloys in simulated oxy-fuel environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeng, Z.; Natesan, K.; Cai, Z.

Increasing the efficiency of coal power plants requires raising the operating temperature above 650°C. However, coal ash can severely attack alloy materials at high temperature. For example, the corrosion rates of commercial Fe- and Ni-based alloys are generally greater than 2 mm/year at 750°C in the gas environment of oxy-fuel combustion. Thus, a critical study is needed to determine the effect of the constituents in the ash on corrosion and find an approach to reduce the corrosion rates in an ash-laden environment at high temperature. The role of CaO in the ash (typical of U.S. Western coal ash) has beenmore » investigated in laboratory exposure environments with various structural alloys. Detailed results are presented on weight change, scale thickness, internal penetration, microstructural characteristics of corrosion products, and the cracking of scales for the alloys after exposure at 750°C. The thermal stability of K3Al(SO4)3 under the environment of oxy-fuel combustion was determined by thermogravimetric analysis and differential thermal analysis. The reaction of this low melting temperature salt with the CaO-containing ash is discussed. In addition, we performed synchrotron nanobeam X-ray analysis to study the phase and chemical composition of the oxide layers on the alloy surface. Results from these studies are used to address the role of CaO in ash in the long-term corrosion performance of alloys.« less

Coal systems analysis: A new approach to the understanding of coal formation, coal quality and environmental considerations, and coal as a source rock for hydrocarbons

USGS Publications Warehouse

Warwick, Peter D.

2005-01-01

Coal is an important and required energy source for today's world. Current rates of world coal consumption are projected to continue at approximately the same (or greater) levels well into the twenty-first century. This paper will provide an introduction to the concept of coal systems analysis and the accompanying volume of papers will provide examples of how coal systems analysis can be used to understand, characterize, and evaluate coal and coal gas resources. Coal systems analysis incorporates the various disciplines of coal geology to provide a complete characterization of the resource. The coal system is divided into four stages: (1) accumulation, (2) preservation-burial, (3) diagenesis-coalification, and (4) coal and hydrocarbon resources. These stages are briefly discussed and key references and examples of the application of coal systems analysis are provided.

Study on the Inference Factors of Huangling Coking Coal Pyrolysis

NASA Astrophysics Data System (ADS)

Du, Meili; Yang, Zongyi; Fan, Jinwen

2018-01-01

In order to reasonably and efficiently utilize Huangling coking coal resource, coal particle, heating rate, holding time, pyrolysis temperature and others factors were dicussed for the influence of those factor on Huangling coking coal pyrolysis products. Several kinds of coal blending for coking experiments were carried out with different kinds of coal such as Huangling coking coal, Xida coal with high ash low sufur, Xinghuo fat coal with hign sulfur, Zhongxingyi coking coal with high sulfur, Hucun lean coal, mixed meager and lean coal. The results shown that the optimal coal particle size distribution was 0.5~1.5mm, the optimal heating rate was 8°C/min, the optimal holding time was 15min, the optimal pyrolysis temperature was 800°C for Huangling coking coal pyrolysis, the tar yield increased from 4.7% to 11.2%. The maximum tar yield of coal blending for coking under the best single factor experiment condition was 10.65% when the proportio of Huangling coking coal was 52%.

Coal desulfurization by chlorinolysis production and combustion test evaluation of product coals

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Daly, D.

1982-01-01

Laboratory-scale screening tests were carried out on coal from Harrison County, Ohio to establish chlorination and hydrodesulfurization conditions for the batch reactor production of chlorinolysis and chlorinolysis-hydrodesulfurized coals. In addition, three bituminous coals, were treated on the lab scale by the chlorinolysis process to provide 39 to 62% desulfurization. Two bituminous coals and one subbituminous coal were then produced in 11 to 15 pound lots as chlorinolysis and hydrodesulfurized coals. The chlorinolysis coals had a desulfurization of 29-69%, reductions in voltatiles and hydrogen. Hydrodesulfurization provided a much greater desulfurization (56-86%), reductions in volatiles and hydrogen. The three coals were combustion tested in the Penn State ""plane flame furnace'' to determine ignition and burning characteristics. All three coals burned well to completion as: raw coals, chlorinolysis processed coals, and hydrodesulfurized coals. The hydrodesulfurized coals experienced greater ignition delays and reduced burning rates than the other coals because of the reduced volatile content. It is thought that the increased open pore volume in the desulfurized-devolatilized coals compensates in part for the decreased volatiles effect on ignition and burning.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The coal industry, the utilities, and the state government are planning for development of high-energy coal gasification in Illinois to convert its abundant high-sulfur coal supply to a substitute natural gas. Following a summary of the findings, the following topics are discussed briefly: Illinois coal and the push for coal gasification; coal gasification: a look at the process; potential sites for an Illinois coal gasification industry; the impact of coal gasification's water requirements; solid wastes from coal gasification; land losses: the impact on agriculture; potential human health problems with coal gasification; the energy efficiency of coal gasification; potential economic impactsmore » of coal gasification; the corporations behind high-energy coal gasification; state involvement: legalizing the losses of the people; the national energy picture: the impact of western coal developments on Illinois; action: what you can do now. 27 references. (MCW)« less

Results of coalbed-methane drilling, Mylan Park, Monongalia County, West Virginia: Chapter G.3 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ruppert, Leslie F.; Fedorko, Nick; Warwick, Peter D.; Grady, William C.; Britton, James Q.; Schuller, William A.; Crangle, Robert D.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

High-pressure carbon-dioxide adsorption isotherms were measured on composite coal samples of the Upper Kittanning coal bed and the Middle Kittanning and Clarion coal zones. Assuming that the reservoir pressure in the Mylan Park coals is equivalent to the normal hydrostatic pressure, the estimated maximum carbon-dioxide adsorption pressures range from a low of about 300 pounds per square inch (lb/in2 ) in coals from the Clarion coal zone to 500 lb/in2 for coals from the Upper Kittanning coal bed. The estimated maximum methane adsorption isotherms show that the coals from the Upper Kittanning coal bed and the Middle Kittanning coal zone are undersaturated in methane, but coals from the Clarion coal zone are close to saturation.

Characterization and organic electric-double-layer-capacitor application of KOH activated coal-tar-pitch-based carbons: Effect of carbonization temperature

NASA Astrophysics Data System (ADS)

Choi, Poo Reum; Lee, Eunji; Kwon, Soon Hyung; Jung, Ji Chul; Kim, Myung-Soo

2015-12-01

The present study reports the influence of pre-carbonization on the properties of KOH-activated coal tar pitch (CTP). The change of crystallinity and pore structure of pre-carbonized CTPs as well as their activated carbons (ACs) as function of pre-carbonization temperature are investigated. The crystallinity of pre-carbonized CTPs increases with increasing the carbonization temperature up to 600 °C, but a disorder occurs during the carbonization around 700 °C and an order happens gradually with increasing the carbonization temperatures in range of 800-1000 °C. The CTPs pre-carbonized at high temperatures are more difficult to be activated with KOH than those pre-carbonized at low temperatures due to the increase of micro-crystalline size and the decrease of surface functional groups. The micro-pores and meso-pores are well developed at around 1.0 nm and 2.4 nm, respectively, as the ACs are pre-carbonized at temperatures of 500-600 °C, exhibiting high specific capacitances as electrode materials for electric double layer capacitor (EDLC). Although the specific surface area (SSA) and pore volume of ACs pre-carbonized at temperatures of 900-1000 °C are extraordinary low (non-porous) as compared to those of AC pre-carbonized at 600 °C, their specific capacitances are comparable to each other. The large specific capacitances with low SSA ACs can be attributed to the structural change resulting from the electrochemical activation during the 1st charge above 2.0 V.

Fireside Corrosion Behaviors of Super304H and HR3C in Coal Ash/Gas Environment with Different SO2 Contents at 650 °C

NASA Astrophysics Data System (ADS)

Lu, Jintao; Yang, Zhen; Li, Yan; Huang, Jinyang; Zhou, Yongli; Zhao, Xinbao; Yuan, Yong

2018-05-01

The corrosion behaviors of Super304H and HR3C used for USC boiler applications were investigated in simulated coal ash/gas environments with 0.1 and 1.5% of SO2 at 650 °C for 500 h. The results indicated that the increase in SO2 accelerated the corrosion rate and the spalling tendency of the corrosion layer in both tested alloys. Fe2O3, Cr2O3 and FeCr2O4 main peaks were revealed by XRD on Super304H, but on HR3C only the Cr2O3 peak showed a high intensity. The SO2 content did not affect the corrosion product composition of any of the alloys, but accelerated the inner sulfidation and the spallation on Super304H. No obvious internal sulfidation was observed on HR3C in either SO2 content. Based on the experimental results, the alloy corrosion mechanism and the influence of sulfur content on the corrosion process were discussed.

Determination of coal ash content by the combined x-ray fluorescence and scattering spectrum

NASA Astrophysics Data System (ADS)

Mikhailov, I. F.; Baturin, A. A.; Mikhailov, A. I.; Borisova, S. S.; Fomina, L. P.

2018-02-01

An alternative method is proposed for the determination of the inorganic constituent mass fraction (ash) in solid fuel by the ratio of Compton and Rayleigh X-ray scattering peaks IC/IR subject to the iron fluorescence intensity. An original X-ray optical scheme with a Ti/Mo (or Sc/Cu) double-layer secondary radiator allows registration of the combined fluorescence-and-scattering spectrum at the specified scattering angle. An algorithm for linear calibration of the Compton-to-Rayleigh IC/IR ratio is proposed which uses standard samples with two certified characteristics: mass fractions of ash (Ad) and iron oxide (WFe2O3). Ash mass fractions have been determined for coals of different deposits in the wide range of Ad from 9.4% to 52.7% mass and WFe2O3 from 0.3% to 4.95% mass. Due to the high penetrability of the probing radiation with energy E > 17 keV, the sample preparation procedure is rather simplified in comparison with the traditional method of Ad determination by the sum of fluorescence intensities of all constituent elements.

Slipping processes in residual badlands reliefs

NASA Astrophysics Data System (ADS)

Díaz-Hernández, Jose Luis; Yepes, Jorge

2010-05-01

We define slips as structures developed by more or less saturated colloidal suspension that slide down the walls of residual reliefs found in badlands. These suspensions seem to originate in the soils crowning gully reliefs and also from rainwater dripping onto the walls of poorly cemented sediments such as siltstone. We call this process slipping and the resulting morphologies represent a group of minor badlands forms, often linked to piping and fluting. Slipping occurs according to the following sequence of forms: 1. Mud droplets. These are irregular linear structures caused by mud droplets sliding down sub-vertical walls. The droplet is usually found at the end of a small channel. These morphologies represent the course of the sliding droplets that become fossilized and not the impact of the droplets on the sediment. 2. Slips sensu stricto. These are uninterrupted surface structures covering sub-vertical walls to a greater or lesser extent. The thickness of this type of covering varies from a few millimetres to 5cm. The inner structure of the slips consists of small laminas (» 100mm) and on the exterior they often present drip channels. A special case of these forms is butterfly structures, which appear in isolation, with repetitive patterns and the appearance of a winged insect stuck to the wall. 3. Pseudo-stalactites. These are free-standing conical regrowths with some similarity to stalactites in a karst cave. They occur when slips grow to over 5cm thick. The growth of these forms is similar to that of slips, with external superposition of fine, concentric layers with no central pore. A variety of these pseudo-stalactites are nodulous stalactites whose genesis is unknown. In this context, we should mention the existence of occasional stalagmites. In other cases, curtains of pseudo-stalactites can be found where these patterns are repeated finely. A more evolved stage of this form is the coalescence of pseudo-stalactites, representing a massive advance of this process. Pseudo-stalactites are normally found as vertical, but occasionally they lean, indicating movement of unstable blocks. The process can present recycling when some of the forms described become detached and fall. This is more likely on poorly sheltered surfaces, exposed to wind and the direct impact of rain and frost. All forms of slips suggests that these morphologies depend on the varying characteristics of the colloidal suspensions causing them, and constitute intermediate stages in the retention of sediments from erosion, which are very different to the alluvial sediments stored in the drainage network.

Interlaboratory comparison of mineral constituents in a sample from the Herrin (No. 6) coal bed from Illinois

USGS Publications Warehouse

Finkelman, Robert B.; Fiene, F.L.; Miller, R.N.; Simon, F.O.

1984-01-01

Approximately 20 kg of the Herrin (No. 6) coal was collected from a strip mine in St. Clair County, Ill. A 10-kg portion was ground to -60 mesh, homogenized, and riffled into 128 splits of 70-80 g each. Homogeneity of these splits was confirmed by moisture, ash, and sulfur analyses of six randomly selected splits. Results of these analyses were within the ASTM (American Society for Testing and Materials) guidelines for interlaboratory precision. Splits of the Herrin (No. 6) coal were then transmitted to more than 30 laboratories for analysis. Low-temperature plasma oxidation was used to isolate inorganic matter for quantitative chemical and mineralogical analysis. Despite a wide variation in ashing conditions, only minor variations in ash yields were obtained; these variations were attributed to differences in operating temperature and moisture content. Mineralogical analyses of low-temperature ash (LTA) concentrates prepared by five different laboratories indicated variations within the limits of analytical error. The mean values, in weight percent, for the major minerals are as follows: calcite, 9; quartz, 20; pyrite, 23; kaolinite, 14; and illite+mixed-layer clays, 31. Normative mineralogical calculations and Fourier transform infrared analysis (FTIR) yielded results similar to those obtained from X-ray diffraction (XRD). Choosing appropriate mineral standards was found to be critical for the proper use of analytical techniques such as XRD and FTIR. Good interlaboratory agreement was obtained for most major, minor, and trace elements despite differences in analytical procedures and in the type of sample analyzed (coal, high-temperature ash, or LTA). Discrepancies between analyses for zinc, strontium, manganese, and iron may be attributed to sampling inhomogeneity problems. Mossbauer spectroscopy showed that approximately 44 percent of the pyritic sulfur was lost through weathering in the first year after preparation of the interlaboratory sample. Szomolnokite and possibly coquimbite and jarosite were also identified. Scanning electron microscopy studies indicated ubiquitous pyrite framboids and, less commonly, euhedral crystals, skeletal grains, irregularly shaped particles, and vein fillings. Minor accessory minerals such as rare-earth phosphates and possibly silicates, zircon, barium sulfate, titanium oxide, and sphalerite were also found. The textural evidence indicates that the minerals in the banded material are detrital whereas the minerals occurring as vein and pore fillings are authigenic. Magnetic measurements indicate that coal crushed in a steel pulverizer is contaminated by small quantities of abrasion fragments from the crusher, which seriously affect the measured magnetic properties of the coal.

Quantitative experimental modelling of fragmentation during explosive volcanism

NASA Astrophysics Data System (ADS)

Thordén Haug, Ø.; Galland, O.; Gisler, G.

2012-04-01

Phreatomagmatic eruptions results from the violent interaction between magma and an external source of water, such as ground water or a lake. This interaction causes fragmentation of the magma and/or the host rock, resulting in coarse-grained (lapilli) to very fine-grained (ash) material. The products of phreatomagmatic explosions are classically described by their fragment size distribution, which commonly follows power laws of exponent D. Such descriptive approach, however, considers the final products only and do not provide information on the dynamics of fragmentation. The aim of this contribution is thus to address the following fundamental questions. What are the physics that govern fragmentation processes? How fragmentation occurs through time? What are the mechanisms that produce power law fragment size distributions? And what are the scaling laws that control the exponent D? To address these questions, we performed a quantitative experimental study. The setup consists of a Hele-Shaw cell filled with a layer of cohesive silica flour, at the base of which a pulse of pressurized air is injected, leading to fragmentation of the layer of flour. The fragmentation process is monitored through time using a high-speed camera. By varying systematically the air pressure (P) and the thickness of the flour layer (h) we observed two morphologies of fragmentation: "lift off" where the silica flour above the injection inlet is ejected upwards, and "channeling" where the air pierces through the layer along sub-vertical conduit. By building a phase diagram, we show that the morphology is controlled by P/dgh, where d is the density of the flour and g is the gravitational acceleration. To quantify the fragmentation process, we developed a Matlab image analysis program, which calculates the number and sizes of the fragments, and so the fragment size distribution, during the experiments. The fragment size distributions are in general described by power law distributions of exponents D. This procedure allows, for the first time, to determine the scaling laws that govern the number of fragments (N), the average size of the fragments (A) and D. We show that (1) N scales with P^(1/2), (2) A scales with P^(-2/3), (3) D scales with P^(1/5). Our experimental procedure thus appears as a unique tool to unravel the complex physics of fragmentation during phreatomagmatic explosions.

Preliminary investigation on the effects of primary airflow to coal particle distribution in coal-fired boilers

NASA Astrophysics Data System (ADS)

Noor, N. A. W. Mohd; Hassan, H.; Hashim, M. F.; Hasini, H.; Munisamy, K. M.

2017-04-01

This paper presents an investigation on the effects of primary airflow to coal fineness in coal-fired boilers. In coal fired power plant, coal is pulverized in a pulverizer, and it is then transferred to boiler for combustion. Coal need to be ground to its desired size to obtain maximum combustion efficiency. Coarse coal particle size may lead to many performance problems such as formation of clinker. In this study, the effects of primary airflow to coal particles size and coal flow distribution were investigated by using isokinetic coal sampling and computational fluid dynamic (CFD) modelling. Four different primary airflows were tested and the effects to resulting coal fineness were recorded. Results show that the optimum coal fineness distribution is obtained at design primary airflow. Any reduction or increase of air flow rate results in undesirable coal fineness distribution.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The first part covers standards for gaseous fuels. The standard part covers standards on coal and coke including the classification of coals, determination of major elements in coal ash and trace elements in coal, metallurgical properties of coal and coke, methods of analysis of coal and coke, petrographic analysis of coal and coke, physical characteristics of coal, quality assurance and sampling.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The first part covers standards for gaseous fuels. The second part covers standards on coal and coke including the classification of coals, determination of major elements in coal ash and trace elements in coal, metallurgical properties of coal and coke, methods of analysis of coal and coke, petrogrpahic analysis of coal and coke, physical characteristics of coal, quality assurance and sampling.

Geochemistry of vanadium (V) in Chinese coals.

PubMed

Liu, Yuan; Liu, Guijian; Qu, Qinyuan; Qi, Cuicui; Sun, Ruoyu; Liu, Houqi

2017-10-01

Vanadium in coals may have potential environmental and economic impacts. However, comprehensive knowledge of the geochemistry of V in coals is lacking. In this study, abundances, distribution and modes of occurrence of V are reviewed by compiling >2900 reported Chinese coal samples. With coal reserves in individual provinces as the weighting factors, V in Chinese coals is estimated to have an average abundance of 35.81 μg/g. Large variation of V concentration is observed in Chinese coals of different regions, coal-forming periods, and maturation ranks. According to the concentration coefficient of V in coals from individual provinces, three regions are divided across Chinese coal deposits. Vanadium in Chinese coals is probably influenced by sediment source and sedimentary environment, supplemented by late-stage hydrothermal fluids. Specifically, hydrothermal fluids have relatively more significant effect on the enrichment of V in local coal seams. Vanadium in coals is commonly associated with aluminosilicate minerals and organic matter, and the modes of V occurrence in coal depend on coal-forming environment and coal rank. The Chinese V emission inventory during coal combustion is estimated to be 4906 mt in 2014, accounting for 50.55 % of global emission. Vanadium emissions by electric power plants are the largest contributor.

Formation and retention of methane in coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hucka, V.J.; Bodily, D.M.; Huang, H.

1992-05-15

The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seamsmore » and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.« less

Formation and retention of methane in coal. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hucka, V.J.; Bodily, D.M.; Huang, H.

1992-05-15

The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seamsmore » and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.« less

Kansas coal distribution, resources, and potential for coalbed methane

USGS Publications Warehouse

Brady, L.L.

2000-01-01

100 ft (>30 m)] determined from 32 different coal beds. Strippable coal resources at a depth Kansas has large amounts of bituminous coal both at the surface and in the subsurface of eastern Kansas. Preliminary studies indicate at least 53 billion tons (48 billion MT) of deep coal [>100 ft (>30 m)] determined from 32 different coal beds. Strippable coal resources at a depth < 100 ft (<30 m) total 2.8 billion tons (2.6 billion MT), and this total is determined from 17 coals. Coal beds present in the Cherokee Group (Middle Pennsylvanian) represent most of these coal resource totals. Deep coal beds with the largest resource totals include the Bevier, Mineral, "Aw" (unnamed coal bed), Riverton, and Weir-Pittsburg coals, all within the Cherokee Group. Based on chemical analyses, coals in the southeastern part of the state are generally high volatile A bituminous, whereas coals in the east-central and northeastern part of the state are high-volatile B bituminous coals. The primary concern of coal beds in Kansas for deep mining or development of coalbed methane is the thin nature [<2 ft (0.6 m)] of most coal beds. Present production of coalbed methane is centered mainly in the southern Wilson/northern Montgomery County area of southeastern Kansas where methane is produced from the Mulky, Weir-Pittsburg, and Riverton coals.

Comparison of the Eastern and Western Kentucky coal fields (Pennsylvanian), USA-why are coal distribution patterns and sulfur contents so different in these coal fields?

USGS Publications Warehouse

Greb, S.F.; Eble, C.F.; Chesnut, D.R.

2002-01-01

More than 130 Mt of Pennsylvanian coal is produced annually from two coal fields in Kentucky. The Western Kentucky Coal Field occurs in part of the Illinois Basin, an intercratonic basin, and the Eastern Kentucky Coal Field occurs in the Central Appalachian Basin, a foreland basin. The basins are only separated by 140 km, but mined western Kentucky coal beds exhibit significantly higher sulfur values than eastern Kentucky coals. Higher-sulfur coal beds in western Kentucky have generally been inferred to be caused by more marine influences than for eastern Kentucky coals. Comparison of strata in the two coal fields shows that more strata and more coal beds accumulated in the Eastern than Western Kentucky Coal Field in the Early and Middle Pennsylvanian, inferred to represent greater generation of tectonic accommodation in the foreland basin. Eastern Kentucky coal beds exhibit a greater tendency toward splitting and occurring in zones than time-equivalent western Kentucky coal beds, which is also inferred to represent foreland accommodation influences, overprinted by autogenic sedimentation effects. Western Kentucky coal beds exhibit higher sulfur values than their eastern counterparts, but western Kentucky coals occurring in Langsettian through Bolsovian strata can be low in sulfur content. Eastern Kentucky coal beds may increase in sulfur content beneath marine zones, but generally are still lower in sulfur than mined Western Kentucky coal beds, indicating that controls other than purely marine influences must have influenced coal quality. The bulk of production in the Eastern Kentucky Coal Field is from Duckmantian and Bolsovian coal beds, whereas production in the Western Kentucky Coal Field is from Westphalian D coals. Langsettian through Bolsovian paleoclimates in eastern Kentucky were favorable for peat doming, so numerous low-sulfur coals accumulated. These coals tend to occur in zones and are prone to lateral splitting because of foreland tectonic and sedimentation influences. In contrast, Westphalian D coal beds of western Kentucky accumulated during low differential tectonic accommodation, and therefore tend to be widespread and uniform in characteristics, but exhibit higher sulfur values because they accumulated in seasonally drier paleoclimates that were unfavorable for peat doming. Hence, basin analyses indicate that many differences between the mined coals of Kentucky's two coal fields are related to temporal changes in paleoclimate and tectonic accommodation, rather than solely being a function of marine influences. ?? 2002 Elsevier Science B.V. All rights reserved.

Reduction of Iron-Oxide-Carbon Composites: Part III. Shrinkage of Composite Pellets during Reduction

NASA Astrophysics Data System (ADS)

Halder, S.; Fruehan, R. J.

2008-12-01

This article involves the evaluation of the volume change of iron-oxide-carbon composite pellets and its implications on reduction kinetics under conditions prevalent in a rotary hearth furnace (RHF) that were simulated in the laboratory. The pellets, in general, were found to shrink considerably during the reduction due to the loss of carbon and oxygen from the system, sintering of the iron-oxide, and formation of a molten slag phase at localized regions inside the pellets due to the presence of binder and coal/wood-charcoal ash at the reduction temperatures. One of the shortcomings of the RHF ironmaking process has been the inability to use multiple layers of composite pellets because of the impediment in heat transport to the lower layers of a multilayer bed. However, pellet shrinkage was found to have a strong effect on the reduction kinetics by virtue of enhancing the external heat transport to the lower layers. The volume change of the different kinds of composite pellets was studied as a function of reduction temperature and time. The estimation of the change in the amount of external heat transport with varying pellet sizes for a particular layer of a multilayer bed was obtained by conducting heat-transfer tests using inert low-carbon steel spheres. It was found that if the pellets of the top layer of the bed shrink by 30 pct, the external heat transfer to the second layer increases by nearly 6 times.

Study on test of coal co-firing for 600MW ultra supercritical boiler with four walls tangential burning

NASA Astrophysics Data System (ADS)

Ying, Wu; Yong-lu, Zhong; Guo-mingi, Yin

2018-06-01

On account of nine commonly used coals in a Jiangxi Power Plant,two kinds of coal were selected to be applied in coal co-firing test through industrial analysis,elementary analysis and thermogravimetric analysis of coal.During the coal co-firing test,two load points were selected,three coal mixtures were prepared.Moreover,under each coal blending scheme, the optimal oxygen content was obtained by oxygen varying test. At last,by measuring the boiler efficiency and coal consumption of power supply in different coal co-firing schemes, the recommended coal co-firing scheme was obtained.

Coal burning issues. [Book - monograph

DOE Office of Scientific and Technical Information (OSTI.GOV)

Green, A.E.S.

1980-01-01

The results of the scoping phase of an interdisciplinary assessment of the impact of the increased use of coal are reported in this monograph. Subject areas include: coal availability and coal mining; an energetics analysis of coal quality; coal transportation; coal burning technology; synthetic fuels from coal; technological innovations; water resources; atmospheric pollution; air pollution dispersion modeling; atmospheric modifications; solid waste and trace element impacts; agriculture; health effects of air pollution resulting from coal combustion; quantitative public policy assessments; financing capacity growth and coal conversions in the electric utility industry; coal and the states - a public choice perspective; andmore » federal regulatory and legal aspects.« less

Liquefaction of calcium-containing subbituminous coals and coals of lower rank

DOEpatents

Brunson, Roy J.

1979-01-01

An improved process for the treatment of a calcium-containing subbituminous coal and coals of lower rank to form insoluble, thermally stable calcium salts which remain within the solids portions of the residue on liquefaction of the coal, thereby suppressing the formation of scale, made up largely of calcium carbonate which normally forms within the coal liquefaction reactor (i.e., coal liquefaction zone), e.g., on reactor surfaces, lines, auxiliary equipment and the like. An oxide of sulfur, in liquid phase, is contacted with a coal feed sufficient to impregnate the pores of the coal. The impregnated coal, in particulate form, can thereafter be liquefied in a coal liquefaction reactor (reaction zone) at coal liquefaction conditions without significant formation of scale.

Coal resources, production, and quality in the Eastern kentucky coal field: Perspectives on the future of steam coal production

USGS Publications Warehouse

Hower, J.C.; Hiett, J.K.; Wild, G.D.; Eble, C.F.

1994-01-01

The Eastern Kentucky coal field, along with adjacent portions of Virginia and southern West Virginia, is part of the greatest production concentration of high-heating-value, low-sulfur coal in the United States, accounting for over 27% of the 1993 U.S. production of coal of all ranks. Eastern Kentucky's production is spread among many coal beds but is particularly concentrated in a limited number of highquality coals, notably the Pond Creek coal bed and its correlatives, and the Fire Clay coal bed and its correlatives. Both coals are relatively low ash and low sulfur through the areas of the heaviest concentration of mining activity. We discuss production trends, resources, and the quality of in-place and clean coal for those and other major coals in the region. ?? 1994 Oxford University Press.

Relationships between waste physicochemical properties, microbial activity and vegetation at coal ash and sludge disposal sites.

PubMed

Woch, Marcin W; Radwańska, Magdalena; Stanek, Małgorzata; Łopata, Barbara; Stefanowicz, Anna M

2018-06-11

The aim of the study was to assess the relationships between vegetation, physicochemical and microbial properties of substrate at coal ash and sludge disposal sites. The study was performed on 32 plots classified into 7 categories: dried ash sedimentation ponds, dominated by a grass Calamagrostis epigejos (AH-Ce), with the admixture of Pinus sylvestris (AH-CePs) or Robinia pseudoacacia (AH-CeRp), dry ash landfill dominated by Betula pendula and Pinus sylvestris (AD-BpPs) or Salix viminalis (AD-Sv) and coal sludge pond with drier parts dominated by Tussilago farfara (CS-Tf) and the wetter ones by Cyperus flavescens (CS-Cf). Ash sites were covered with soil layer imported as a part of technical reclamation. Ash had relatively high concentrations of some alkali and alkaline earth metals, Mn and pH, while coal sludge had high water and C, S, P and K contents. Concentrations of heavy metals were lower than allowable limits in all substrate types. Microbial biomass and, particularly, enzymatic activity in ash and sludge were generally low. The only exception were CS-Tf plots characterized by the highest microbial biomass, presumably due to large deposits of organic matter that became available for aerobic microbial biomass when water level fell. The properties of ash and sludge adversely affected microbial biomass and enzymatic activity as indicated by significant negative correlations between the content of alkali/alkaline earth metals, heavy metals, and macronutrients with enzymatic activity and/or microbial biomass, as well as positive correlations of these parameters with metabolic quotient (qCO 2 ). Plant species richness and cover were relatively high, which may be partly associated with alleviating influence of soil covering the ash. The effect of the admixture of R. pseudoacacia or P. sylvestris to stands dominated by C. epigejos was smaller than expected. The former species increased NNH 4 , NNO 3 and arylsulfatase activity, while the latter reduced activity of the enzyme. Copyright © 2018 Elsevier B.V. All rights reserved.

Iranian Tentacles into Iraq: The Basis and Extent of Iranian Influence into Southern Iraq

DTIC Science & Technology

2009-01-01

cultural values, based on their historical development. Tehran uses methods along the spectrum of psychological persuasion to influence and subvert the ...49 pages. Most of those who comment on Iran’s attempt to influence Iraqi Shia, do so without considering the historical and cultural connection...varied cultural values, based on their historical development. Tehran uses methods along the spectrum of psychological persuasion to influence and

The Rise and Fall of the Renaissance Party: Implications of De-Ba’athification on Iraqi Society

DTIC Science & Technology

2004-05-03

the familiar likeness of the ancient Mesopotamian kings mixed with the familiar visage of Saddam Hussein. Saddam’s...Iraqi culture . Saddam made significant strides in ridding Iraq of illiteracy, yet even this largely successful effort was subverted to educate the ...fragmented by ethnicity, language, culture , political leanings, and beliefs on the role of women, and the struggle for the role of secularism

Security Policy Enforcement

DTIC Science & Technology

2005-09-21

most notable was the CAP sys- tem (Wilkes & Needham, 1980 ). Although they can be im- plemented, the systems are notoriously complex and their lack of...when a system is subverted (Anderson, Irvine, & Schell, 2004; Myers, 1980 ). In this case, a member of the system’s development team intentionally adds...Cooper, R. H., Hyslop , W. F., Nickerson, B. G., Stewart, W. M., & Ward, O. K. (1993). The cascade vulnerability problem. In Proceedings of the IEEE

Subverting Risk Attachment as Consideration for Insurance Contracts: Kansas City College of Osteopathic Medicine v. Employers' Surplus Lines Insurance Co.

ERIC Educational Resources Information Center

Sweeney, Patricia J.

1980-01-01

Legal implications and court rulings are reviewed for a case in which a medical college requested a premium refund and cancellation of the bond. It is concluded that the court decision in favor of the insurance company was inappropriate and tends to undermine insurance law. (Journal availibility: Boston U. School of Law, Boston, MA 02215) (MSE)

19th Century Christian Benevolence and the Unwritten Constitution

DTIC Science & Technology

2007-05-01

indispensable supports. In vain would that man claim the tribute of Patriotism, who should labour to subvert these great Pillars of human happiness...Brought on by disestablishment and buoyed by the energy from the Second Great Awakening, ecumenical Protestantism jettisoned the artificial barriers of the...highest to the lowest, as coworkers in the same labour of love.’’ 23 Efficiency in distribution, however, required accurate communication between the

Subverting Host Cell P21-Activated Kinase: A Case of Convergent Evolution across Pathogens.

PubMed

John Von Freyend, Simona; Kwok-Schuelein, Terry; Netter, Hans J; Haqshenas, Gholamreza; Semblat, Jean-Philippe; Doerig, Christian

2017-04-21

Intracellular pathogens have evolved a wide range of strategies to not only escape from the immune systems of their hosts, but also to directly exploit a variety of host factors to facilitate the infection process. One such strategy is to subvert host cell signalling pathways to the advantage of the pathogen. Recent research has highlighted that the human serine/threonine kinase PAK, or p21-activated kinase, is a central component of host-pathogen interactions in many infection systems involving viruses, bacteria, and eukaryotic pathogens. PAK paralogues are found in most mammalian tissues, where they play vital roles in a wide range of functions. The role of PAKs in cell proliferation and survival, and their involvement in a number of cancers, is of great interest in the context of drug discovery. In this review we discuss the latest insights into the surprisingly central role human PAK1 plays for the infection by such different infectious disease agents as viruses, bacteria, and parasitic protists. It is our intention to open serious discussion on the applicability of PAK inhibitors for the treatment, not only of neoplastic diseases, which is currently the primary objective of drug discovery research targeting these enzymes, but also of a wide range of infectious diseases.

Mycobacterium tuberculosis manipulates pulmonary APCs subverting early immune responses.

PubMed

Garcia-Romo, Gina S; Pedroza-Gonzalez, Alexander; Lambrecht, Bart N; Aguilar-Leon, Diana; Estrada-Garcia, Iris; Hernandez-Pando, Rogelio; Flores-Romo, Leopoldo

2013-03-01

Alveolar macrophages (AM) and dendritic cells (DCs) are the main antigen presenting cells (APCs) in the respiratory tract. Whereas macrophages have been extensively studied in tuberculosis, in situ interactions of DC with Mycobacterium tuberculosis (Mtb) are poorly explored. We aimed to characterize lung APCs during pulmonary tuberculosis in Balb/C mice infected with Mtb H37Rv. Mtb-infection via the airways induced a delayed and continuous accumulation of DCs and AM in the lungs. While lung DCs increased after day 3 post-infection, macrophages increased after 2-3 weeks. Although both populations accumulated in lungs during the infection, DCs decreased in the late stages. Infection induced differential expression of co-stimulatory molecules in these lung APCs, decreasing to basal levels in both APCs in the late stages. A remarkable segregation was found regarding bacillary burden. Many macrophages contained numerous bacilli, but DC contained scarce mycobacteria or none. Mtb-infection also induced delayed accumulation of DC in draining lymph nodes. This delayed recruitment was not associated with a lack of IL-12p40, which was detected from day 3 post-infection. Although AM and lung DCs behave differently during pulmonary tuberculosis, Mtb apparently manipulates both lung APCs subverting early protective responses resulting in disease progression. Copyright © 2012 Elsevier GmbH. All rights reserved.

Trypanosoma cruzi subverts the sphingomyelinase-mediated plasma membrane repair pathway for cell invasion

PubMed Central

Fernandes, Maria Cecilia; Cortez, Mauro; Flannery, Andrew R.; Tam, Christina; Mortara, Renato A.

2011-01-01

Upon host cell contact, the protozoan parasite Trypanosoma cruzi triggers cytosolic Ca2+ transients that induce exocytosis of lysosomes, a process required for cell invasion. However, the exact mechanism by which lysosomal exocytosis mediates T. cruzi internalization remains unclear. We show that host cell entry by T. cruzi mimics a process of plasma membrane injury and repair that involves Ca2+-dependent exocytosis of lysosomes, delivery of acid sphingomyelinase (ASM) to the outer leaflet of the plasma membrane, and a rapid form of endocytosis that internalizes membrane lesions. Host cells incubated with T. cruzi trypomastigotes are transiently wounded, show increased levels of endocytosis, and become more susceptible to infection when injured with pore-forming toxins. Inhibition or depletion of lysosomal ASM, which blocks plasma membrane repair, markedly reduces the susceptibility of host cells to T. cruzi invasion. Notably, extracellular addition of sphingomyelinase stimulates host cell endocytosis, enhances T. cruzi invasion, and restores normal invasion levels in ASM-depleted cells. Ceramide, the product of sphingomyelin hydrolysis, is detected in newly formed parasitophorous vacuoles containing trypomastigotes but not in the few parasite-containing vacuoles formed in ASM-depleted cells. Thus, T. cruzi subverts the ASM-dependent ceramide-enriched endosomes that function in plasma membrane repair to infect host cells. PMID:21536739

MoYvh1 subverts rice defense through functions of ribosomal protein MoMrt4 in Magnaporthe oryzae.

PubMed

Liu, Xinyu; Yang, Jie; Qian, Bin; Cai, Yongchao; Zou, Xi; Zhang, Haifeng; Zheng, Xiaobo; Wang, Ping; Zhang, Zhengguang

2018-04-01

The accumulation of the reactive oxygen species (ROS) in rice is important in its interaction with the rice blast fungus Magnaporthe oryzae during which the pathogen scavenges ROS through the production of extracellular enzymes that promote blast. We previously characterized the MoYvh1 protein phosphatase from M. oryzae that plays a role in scavenging of ROS. To understand the underlying mechanism, we found that MoYvh1 is translocated into the nucleus following oxidative stress and that this translocation is dependent on MoSsb1 and MoSsz1 that are homologous to heat-shock protein 70 (Hsp70) proteins. In addition, we established a link between MoYvh1 and MoMrt4, a ribosome maturation factor homolog whose function also involves shuttling between the cytoplasm and the nucleus. Moreover, we found that MoYvh1 regulates the production of extracellular proteins that modulate rice-immunity. Taking together, our evidence suggests that functions of MoYvh1 in regulating ROS scavenging require its nucleocytoplasmic shuttling and the partner proteins MoSsb1 and MoSsz1, as well as MoMrt4. Our findings provide novel insights into the mechanism by which M. oryzae responds to and subverts host immunity through the regulation of ribosome biogenesis and protein biosynthesis.

The Dialogue of the Host-Parasite Relationship: Leishmania spp. and Trypanosoma cruzi Infection

PubMed Central

de Morais, Carlos Gustavo Vieira; Castro Lima, Ana Karina; dos Santos, Rosiane Freire; Da-Silva, Silvia Amaral Gonçalves; Dutra, Patrícia Maria Lourenço

2015-01-01

The intracellular protozoa Leishmania spp. and Trypanosoma cruzi and the causative agents of Leishmaniasis and Chagas disease, respectively, belong to the Trypanosomatidae family. Together, these two neglected tropical diseases affect approximately 25 million people worldwide. Whether the host can control the infection or develops disease depends on the complex interaction between parasite and host. Parasite surface and secreted molecules are involved in triggering specific signaling pathways essential for parasite entry and intracellular survival. The recognition of the parasite antigens by host immune cells generates a specific immune response. Leishmania spp. and T. cruzi have a multifaceted repertoire of strategies to evade or subvert the immune system by interfering with a range of signal transduction pathways in host cells, which causes the inhibition of the protective response and contributes to their persistence in the host. The current therapeutic strategies in leishmaniasis and trypanosomiasis are very limited. Efficacy is variable, toxicity is high, and the emergence of resistance is increasingly common. In this review, we discuss the molecular basis of the host-parasite interaction of Leishmania and Trypanosoma cruzi infection and their mechanisms of subverting the immune response and how this knowledge can be used as a tool for the development of new drugs. PMID:26090399

Nanometre-sized pores in coal: Variations between coal basins and coal origin

USGS Publications Warehouse

Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

2018-01-01

We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

Economic effects of western Federal land-use restrictions on U.S. coal markets

USGS Publications Warehouse

Watson, William Downing; Medlin, A.L.; Krohn, K.K.; Brookshire, D.S.; Bernknopf, R.L.

1991-01-01

Current regulations on land use in the Western United States affect access to surface minable coal resources. This U.S. Geological Survey study analyzes the long-term effects of Federal land-use restrictions on the national cost of meeting future coal demands. The analysis covers 45 years. The U.S. Bureau of Land Management has determined the environmental, aesthetic, and economic values of western Federal coal lands and has set aside certain areas from surface coal mining to protect other valued land uses, including agricultural, environmental, and aesthetic uses. Although there are benefits to preserving natural areas and to developing areas for other land uses, these restrictions produce long-term national and regional costs that have not been estimated previously. The Dynamic Coal Allocation Model integrates coal supply (coal resource tonnage and coal quality by mining cost for 60 coal supply regions) with coal demand (in 243 regions) for the entire United States. The model makes it possible to evaluate the regional economic impacts of coal supply restrictions wherever they might occur in the national coal market. The main factors that the economic methodology considers are (1) coal mining costs, (2) coal transportation costs, (3) coal flue gas desulfurization costs, (4) coal demand, (5) regulations to control sulfur dioxide discharges, and (6) specific reductions in coal availability occurring as a result of land-use restrictions. The modeling system combines these economic factors with coal deposit quantity and quality information--which is derived from the U.S. Geological Survey's National Coal Resources Data System and the U.S. Department of Energy's Demonstrated Reserve Base--to determine a balance between supply and demand so that coal is delivered at minimum cost.

Chemical and mineralogical characterization of highly and less reactive coal from Northern Natal and Venda-Pafuri coalfields in South Africa

NASA Astrophysics Data System (ADS)

Kataka, M. O.; Matiane, A. R.; Odhiambo, B. D. O.

2018-01-01

Spontaneous combustion of coal is a major hazard associated with the coal mining industry over centuries. It also a major cause of underground fires in South African collieries and in opencast operations, spoil heaps and stockpiles. Spontaneous combustion incidents are manifested in all major aspects of coal mining namely, underground mining, surface mining, including during sea-borne transportation, storage and waste disposal. Previous studies indicate that there are various factors (both intrinsic and extrinsic) that influence the spontaneous combustion of coals. This paper characterizes highly reactive coal from the Vryheid coalfields and less reactive coal from at Venda-Pafuri coalfield, to identify and delineate some intrinsic coal parameters that are considered to be most critical in terms of heat 'generation' and relationships between the two coals types by tracing their similarities and differences in their spontaneous combustion parameters. Various tests were carried out to characterize these coals in terms of their intrinsic properties, namely: ultimate, proximate, petrographic analysis and Glasser spontaneous tests. The ultimate and proximate analysis showed that spontaneous coal has high contents of carbon, oxygen, and volatile matter as compared to non-spontaneous coal, making it more susceptible to spontaneous combustion. Non-spontaneous coal has higher ash content than the spontaneous coal. Furthermore, the petrographic analysis showed that spontaneous coal has high total reactivity compared to the non-spontaneous coal. Results from Glasser spontaneous test indicate that spontaneous coal absorbs more oxygen than non-spontaneous coal, which explains why spontaneous coal is more susceptible to spontaneous combustion. High reactive coal has low values of critical self-heating temperature (CSHT), indicating that this coal has potential of spontaneous ignition.

Proceedings: Fourteenth annual EPRI conference on fuel science

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-05-01

EPRI's Fourteenth Annual Contractors' Conference on Fuel Science was held on May 18--19, 1989 in Palo Alto, CA. The conference featured results of work on coal science, coal liquefaction, methanol production, and coal oil coprocessing and coal upgrading. The following topics were discussed: recent development in coal liquefaction at the Wilsonville Clean Coal Research Center; British coal's liquid solvent extraction (LSE) process; feedstock reactivity in coal/oil co-processing; utility applications for coal-oil coprocessed fuels; effect of coal rank and quality on two-stage liquefaction; organic sulfur compounds in coals; the perchloroethylene refining process of high-sulfur coals; extraction of sulfur coals; extraction ofmore » sulfur from coal; agglomeration of bituminous and subbituminous coals; solubilization of coals by cell-free extracts derived from polyporus versicolor; remediation technologies and services; preliminary results from proof-of-concept testing of heavy liquid cyclone cleaning technology; clean-up of soil contaminated with tarry/oily organics; midwest ore processing company's coal benefication technology: recent prep plant, scale and laboratory activities; combustion characterization of coal-oil agglomerate fuels; status report on the liquid phase methanol project; biomimetic catalysis; hydroxylation of C{sub 2} {minus} C{sub 3} and cycloc{sub 6} hydrocarbons with Fe cluster catalysts as models for methane monooxygenase enzyme; methanol production scenarios; and modeling studies of the BNL low temperature methanol catalyst. Individual projects are processed separately for the data bases.« less

Appalachian coal assessment: Defining the coal systems of the Appalachian basin

USGS Publications Warehouse

Milici, R.C.

2005-01-01

The coal systems concept may be used to organize the geologic data for a relatively large, complex area, such as the Appalachian basin, in order to facilitate coal assessments in the area. The concept is especially valuable in subjective assessments of future coal production, which would require a detailed understanding of the coal geology and coal chemistry of the region. In addition, subjective assessments of future coal production would be enhanced by a geographical information system that contains the geologic and geochemical data commonly prepared for conventional coal assessments. Coal systems are generally defined as one or more coal beds or groups of coal beds that have had the same or similar genetic history from their inception as peat deposits, through their burial, diagenesis, and epigenesis to their ultimate preservation as lignite, bituminous coal, or anthracite. The central and northern parts of the Appalachian basin contain seven coal systems (Coal Systems A-G). These systems may be defined generally on the following criteria: (1) on the primary characteristics of their paleopeat deposits, (2) on the stratigraphic framework of the Paleozoic coal measures, (3) on the relative abundance of coal beds within the major stratigraphic groupings, (4) on the amount of sulfur related to the geologic and climatic conditions under which paleopeat deposits accumulated, and (5) on the rank of the coal (lignite to anthracite). ??2005 Geological Society of America.

Advanced liquefaction using coal swelling and catalyst dispersion techniques. Volume 2, appendices. Final technical report, October 1, 1991--September 30, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis, C.W.; Chander, S.; Gutterman, C.

Liquefaction experiments were undertaken using subbituminous Black Thunder mine coal to observe the effects of aqueous SO{sub 2} coal beneficiation and the introduction of various coal swelling solvents and catalyst precursors. Aqueous SO{sub 2} beneficiation of Black Thunder coal removed alkali metals and alkaline earth metals, increased the sulfur content and increased the catalytic liquefaction conversion to THF solubles compared to untreated Black Thunder coal. The liquefaction solvent had varying effects on coal conversion, depending upon the type of solvent added. The hydrogen donor solvent, dihydroanthracene, was most effective, while a coal-derived Wilsonville solvent promoted more coal conversion than didmore » relatively inert 1-methylnaphthalene. Swelling of coal with hydrogen bonding solvents tetrahydrofuran (THF), isopropanol, and methanol, prior to reaction resulted in increased noncatalytic conversion of both untreated and SO{sub 2} treated Black Thunder coals, while dimethylsulfoxide (DMSO), which was absorbed more into the coal than any other swelling solvent, was detrimental to coal conversion. Swelling of SO{sub 2} treated coal before liquefaction resulted in the highest coal conversions; however, the untreated coal showed the most improvements in catalytic reactions when swelled in either THF, isopropanol, or methanol prior to liquefaction. The aprotic solvent DMSO was detrimental to coal conversion.« less

Coal systems analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warwick, P.D.

This collection of papers provides an introduction to the concept of coal systems analysis and contains examples of how coal systems analysis can be used to understand, characterize, and evaluate coal and coal gas resources. Chapter are: Coal systems analysis: A new approach to the understanding of coal formation, coal quality and environmental considerations, and coal as a source rock for hydrocarbons by Peter D. Warwick. Appalachian coal assessment: Defining the coal systems of the Appalachian Basin by Robert C. Milici. Subtle structural influences on coal thickness and distribution: Examples from the Lower Broas-Stockton coal (Middle Pennsylvanian), Eastern Kentucky Coalmore » Field, USA by Stephen F. Greb, Cortland F. Eble, and J.C. Hower. Palynology in coal systems analysis The key to floras, climate, and stratigraphy of coal-forming environments by Douglas J. Nichols. A comparison of late Paleocene and late Eocene lignite depositional systems using palynology, upper Wilcox and upper Jackson Groups, east-central Texas by Jennifer M.K. O'Keefe, Recep H. Sancay, Anne L. Raymond, and Thomas E. Yancey. New insights on the hydrocarbon system of the Fruitland Formation coal beds, northern San Juan Basin, Colorado and New Mexico, USA by W.C. Riese, William L. Pelzmann, and Glen T. Snyder.« less

Relationship between Maceral of Coal and Coal-bed Methane adsorption ability in Sihe Coalmine of Qinshui Basin, China

NASA Astrophysics Data System (ADS)

Wang, M. S.; Zou, G. G.; Zhu, R. B.

2018-05-01

Maceral components and its content of coal were divided based on the microscopic characteristics of coal. The Langmuir volume and the Langmuir pressure were tested, and the Langmuir volume represents the adsorption capacity of coal. The formation of coal bed methane is affected by the partition of the maceral components in coal. Therefore, the relationship between maceral composition and coal bed methane adsorption capacity of coal was analyzed. The results show that the maceral components of coal are dominated by vitrinite and inertinite in the study area, and the content of inertinite is below 32%. The vitrinite group has a negative linear correlation with the Langmuir volume, and the inertia composition has a positive linear correlation with it. The cellular structures in the inertinite are the main site of coal bed methane enrichment. The microstructure of coal affects the coalbed methane content and the stage of hydrocarbon generation in coal. This indicates that the microstructure of coal is one of the important factors influencing the adsorption capacity of coal seam.

Assessment of coal geology, resources, and reserves in the northern Wyoming Powder River Basin

USGS Publications Warehouse

Scott, David C.; Haacke, Jon E.; Osmonson, Lee M.; Luppens, James A.; Pierce, Paul E.; Rohrbacher, Timothy J.

2010-01-01

The abundance of new borehole data from recent coal bed natural gas development in the Powder River Basin was utilized by the U.S. Geological Survey for the most comprehensive evaluation to date of coal resources and reserves in the Northern Wyoming Powder River Basin assessment area. It is the second area within the Powder River Basin to be assessed as part of a regional coal assessment program; the first was an evaluation of coal resources and reserves in the Gillette coal field, adjacent to and south of the Northern Wyoming Powder River Basin assessment area. There are no active coal mines in the Northern Wyoming Powder River Basin assessment area at present. However, more than 100 million short tons of coal were produced from the Sheridan coal field between the years 1887 and 2000, which represents most of the coal production within the northwestern part of the Northern Wyoming Powder River Basin assessment area. A total of 33 coal beds were identified during the present study, 24 of which were modeled and evaluated to determine in-place coal resources. Given current technology, economic factors, and restrictions to mining, seven of the beds were evaluated for potential reserves. The restrictions included railroads, a Federal interstate highway, urban areas, and alluvial valley floors. Other restrictions, such as depth, thickness of coal beds, mined-out areas, and areas of burned coal, were also considered. The total original coal resource in the Northern Wyoming Powder River Basin assessment area for all 24 coal beds assessed, with no restrictions applied, was calculated to be 285 billion short tons. Available coal resources, which are part of the original coal resource that is accessible for potential mine development after subtracting all restrictions, are about 263 billion short tons (92.3 percent of the original coal resource). Recoverable coal, which is that portion of available coal remaining after subtracting mining and processing losses, was determined for seven coal beds with a stripping ratio of 10:1 or less. After mining and processing losses were subtracted, a total of 50 billion short tons of recoverable coal was calculated. Coal reserves are the portion of the recoverable coal that can be mined, processed, and marketed at a profit at the time of the economic evaluation. With a discounted cash flow at 8 percent rate of return, the coal reserves estimate for the Northern Wyoming Powder River Basin assessment area is 1.5 billion short tons of coal (1 percent of the original resource total) for the seven coal beds evaluated.

Study on the coal mixing ratio optimization for a power plant

NASA Astrophysics Data System (ADS)

Jin, Y. A.; Cheng, J. W.; Bai, Q.; Li, W. B.

2017-12-01

For coal-fired power plants, the application of blended coal combustion has been a great issue due to the shortage and rising prices of high-rank coal. This paper describes the optimization of blending methods between Xing'an lignite coal, Shaltala lignite coal, Ura lignite coal, and Inner Mongolia bituminous coal. The multi-objective decision-making method based on fuzzy mathematics was used to determine the optimal blending ratio to improve the power plant coal-fired economy.

Assessment of Coal Geology, Resources, and Reserves in the Gillette Coalfield, Powder River Basin, Wyoming

USGS Publications Warehouse

Luppens, James A.; Scott, David C.; Haacke, Jon E.; Osmonson, Lee M.; Rohrbacher, Timothy J.; Ellis, Margaret S.

2008-01-01

The Gillette coalfield, within the Powder River Basin in east-central Wyoming, is the most prolific coalfield in the United States. In 2006, production from the coalfield totaled over 431 million short tons of coal, which represented over 37 percent of the Nation's total yearly production. The Anderson and Canyon coal beds in the Gillette coalfield contain some of the largest deposits of low-sulfur subbituminous coal in the world. By utilizing the abundance of new data from recent coalbed methane development in the Powder River Basin, this study represents the most comprehensive evaluation of coal resources and reserves in the Gillette coalfield to date. Eleven coal beds were evaluated to determine the in-place coal resources. Six of the eleven coal beds were evaluated for reserve potential given current technology, economic factors, and restrictions to mining. These restrictions included the presence of railroads, a Federal interstate highway, cities, a gas plant, and alluvial valley floors. Other restrictions, such as thickness of overburden, thickness of coal beds, and areas of burned coal were also considered. The total original coal resource in the Gillette coalfield for all eleven coal beds assessed, and no restrictions applied, was calculated to be 201 billion short tons. Available coal resources, which are part of the original coal resource that is accessible for potential mine development after subtracting all restrictions, are about 164 billion short tons (81 percent of the original coal resource). Recoverable coal, which is the portion of available coal remaining after subtracting mining and processing losses, was determined for a stripping ratio of 10:1 or less. After mining and processing losses were subtracted, a total of 77 billion short tons of coal were calculated (48 percent of the original coal resource). Coal reserves are the portion of the recoverable coal that can be mined, processed, and marketed at a profit at the time of the economic evaluation. With a discounted cash flow at 8 percent rate of return, the coal reserves estimate for the Gillette coalfield is10.1 billion short tons of coal (6 percent of the original resource total) for the 6 coal beds evaluated.

Effect of Water Invasion on Outburst Predictive Index of Low Rank Coals in Dalong Mine

PubMed Central

Jiang, Jingyu; Cheng, Yuanping; Mou, Junhui; Jin, Kan; Cui, Jie

2015-01-01

To improve the coal permeability and outburst prevention, coal seam water injection and a series of outburst prevention measures were tested in outburst coal mines. These methods have become important technologies used for coal and gas outburst prevention and control by increasing the external moisture of coal or decreasing the stress of coal seam and changing the coal pore structure and gas desorption speed. In addition, techniques have had a significant impact on the gas extraction and outburst prevention indicators of coal seams. Globally, low rank coals reservoirs account for nearly half of hidden coal reserves and the most obvious feature of low rank coal is the high natural moisture content. Moisture will restrain the gas desorption and will affect the gas extraction and accuracy of the outburst prediction of coals. To study the influence of injected water on methane desorption dynamic characteristics and the outburst predictive index of coal, coal samples were collected from the Dalong Mine. The methane adsorption/desorption test was conducted on coal samples under conditions of different injected water contents. Selective analysis assessed the variations of the gas desorption quantities and the outburst prediction index (coal cutting desorption index). Adsorption tests indicated that the Langmuir volume of the Dalong coal sample is ~40.26 m3/t, indicating a strong gas adsorption ability. With the increase of injected water content, the gas desorption amount of the coal samples decreased under the same pressure and temperature. Higher moisture content lowered the accumulation desorption quantity after 120 minutes. The gas desorption volumes and moisture content conformed to a logarithmic relationship. After moisture correction, we obtained the long-flame coal outburst prediction (cutting desorption) index critical value. This value can provide a theoretical basis for outburst prediction and prevention of low rank coal mines and similar occurrence conditions of coal seams. PMID:26161959

The effect of coal bed dewatering and partial oxidation on biogenic methane potential

USGS Publications Warehouse

Jones, Elizabeth J.P.; Harris, Steve H.; Barnhart, Elliott P.; Orem, William H.; Clark, Arthur C.; Corum, Margo D.; Kirshtein, Julie D.; Varonka, Matthew S.; Voytek, Mary A.

2013-01-01

Coal formation dewatering at a site in the Powder River Basin was associated with enhanced potential for secondary biogenic methane determined by using a bioassay. We hypothesized that dewatering can stimulate microbial activity and increase the bioavailability of coal. We analyzed one dewatered and two water-saturated coals to examine possible ways in which dewatering influences coal bed natural gas biogenesis by looking at differences with respect to the native coal microbial community, coal-methane organic intermediates, and residual coal oxidation potential. Microbial biomass did not increase in response to dewatering. Small Subunit rRNA sequences retrieved from all coals sampled represented members from genera known to be aerobic, anaerobic and facultatively anaerobic. A Bray Curtis similarity analysis indicated that the microbial communities in water-saturated coals were more similar to each other than to the dewatered coal, suggesting an effect of dewatering. There was a higher incidence of long chain and volatile fatty acid intermediates in incubations of the dewatered coal compared to the water-saturated coals, and this could either be due to differences in microbial enzymatic activities or to chemical oxidation of the coal associated with O2 exposure. Dilute H2O2 treatment of two fractions of structural coal (kerogen and bitumen + kerogen) was used as a proxy for chemical oxidation by O2. The dewatered coal had a low residual oxidation potential compared to the water-saturated coals. Oxidation with 5% H2O2 did increase the bioavailability of structural coal, and the increase in residual oxidation potential in the water saturated coals was approximately equivalent to the higher methanogenic potential measured in the dewatered coal. Evidence from this study supports the idea that coal bed dewatering could stimulate biogenic methanogenesis through partial oxidation of the structural organics in coal once anaerobic conditions are restored.

Uncertainty in coal property valuation in West Virginia: A case study

USGS Publications Warehouse

Hohn, M.E.; McDowell, R.R.

2001-01-01

Interpolated grids of coal bed thickness are being considered for use in a proposed method for taxation of coal in the state of West Virginia (United States). To assess the origin and magnitude of possible inaccuracies in calculated coal tonnage, we used conditional simulation to generate equiprobable realizations of net coal thickness for two coals on a 7 1/2 min topographic quadrangle, and a third coal in a second quadrangle. Coals differed in average thickness and proportion of original coal that had been removed by erosion; all three coals crop out in the study area. Coal tonnage was calculated for each realization and for each interpolated grid for actual and artificial property parcels, and differences were summarized as graphs of percent difference between tonnage calculated from the grid and average tonnage from simulations. Coal in individual parcels was considered minable for valuation purposes if average thickness in each parcel exceeded 30 inches. Results of this study show that over 75% of the parcels are classified correctly as minable or unminable based on interpolation grids of coal bed thickness. Although between 80 and 90% of the tonnages differ by less than 20% between interpolated values and simulated values, a nonlinear conditional bias might exist in estimation of coal tonnage from interpolated thickness, such that tonnage is underestimated where coal is thin, and overestimated where coal is thick. The largest percent differences occur for parcels that are small in area, although because of the small quantities of coal in question, bias is small on an absolute scale for these parcels. For a given parcel size, maximum apparent overestimation of coal tonnage occurs in parcels with an average coal bed thickness near the minable cutoff of 30 in. Conditional bias in tonnage for parcels having a coal thickness exceeding the cutoff by 10 in. or more is constant for two of the three coals studied, and increases slightly with average thickness for the third coal. ?? 2001 International Association for Mathematical Geology.

Floatabilities of treated coal in water at room temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kwon, K.C.; Rohrer, R.L.; Lai, R.W.

1995-04-01

Experiments on equilibrium adsorption loadings of various probe compounds on 60-200 mesh Illinois No. 6 coal (PSOC-1539), Adaville No. 1 coal (PSOC-1544), Wyodak coal (PSOC-1545), and Pittsburgh No. 8 coal (PSOC-1549) were performed. The probe compounds include 2-methyl-1-pentanol (2M1P), 1-heptanol, benzene, and toluene. Equilibrium adsorption loadings of aromatic compounds such as toluene and benzene on the four chosen coals obey the Langmuir isotherm model up to 100 ppm in concentrations of probe compounds. Equilibrium adsorption loadings of higher aliphatic alcohols such as 2M1P and 1-heptanol on the four chosen coals do not follow both the Langmuir isotherm model and themore » Freundlich empirical adsorption model. Flotation of the coals, equilibrated with aqueous solutions of 2M1P and 1-heptanol, increases linearly with equilibrium adsorption loadings of these probe compounds on the coals. The chosen coals were treated with nitrogen and air at 1 atm and 125-225{degrees}C for 24 h. Flotation experiments of the treated coals were conducted at room temperature, using distilled water only as a flotation medium. Flotation of Adaville No. 1 coal and Wyodak coal treated with nitrogen gas is higher than that of the untreated coals and increases with treatment temperatures. Flotation of Adaville No. 1 coal treated with air at 125-225{degrees}C is not significantly different from that of untreated coal. Flotation of Pittsburgh No. 8 coal treated with air is lower than that of untreated coal and decreases with treatment temperatures. Flotation of Illinois No. 6 coal treated with nitrogen with nitrogen only is higher than that of untreated coal. Flotation of Illinois No. 6 coal treated with nitrogen at 125-175{degrees}C increases with treatment temperatures, whereas flotation of Illinois No. 6 coal treated with nitrogen at 174-225{degrees}C decreases with treatment temperatures.« less

Block coals from Indiana: Inferences on changing depositional environment

USGS Publications Warehouse

Mastalerz, Maria; Padgett, P.L.; Eble, C.F.

2000-01-01

Significant differences in coal petrography, palynology and coal quality were found between the Lower Block and Upper Block Coal Members (Brazil Formation, Pennsylvanian) in Daviess County, Indiana. The Lower Block Coal Member ranges in thickness from 51 to 74 cm and the Upper Block Coal Member ranges from 20 to 65 cm. Average sulfur content and ash yield of the Lower Block coal (0.98%, 7.65%) are lower than in the Upper Block coal. Megascopically, the coals show distinct differences. The Lower Block is a banded coal with numerous thin fusain horizons and a thin clay parting in the lower third of the seam. The Upper Block coal has a dulling-upward trend, with a bright clarain found at the base that grades into a clarain and then into a durain in the upper portion of the seam. Vitrinite content of the Lower Block coal ranges from 63% to 78%, with the highest vitrinite content found in the middle portion of the seam. In the Upper Block coal, vitrinite content ranges from 40% to 83%, with the highest values found in the lower part of the seam. Ash yield is higher in the upper part of the Upper Block coal, reaching up to 40%. The Lower Block coal is dominated by lycopod trees and tree ferns. The Upper Block coal shows marked differences in spore assemblages between lower and upper parts of the seam. The lower half is dominated by large lycopod trees and tree ferns, similar to the Lower Block coal. The upper half is dominated by small lycopods, mainly Densosporites and Radiizonates. These differences between the Lower Block and Upper Block Coal Members are significant correlation tools applicable to mining exploration and chronostratigraphy. (C) 2000 Elsevier Science B.V. All rights reserved.Significant differences in coal petrography, palynology and coal quality were found between the Lower Block and Upper Block Coal Members (Brazil Formation, Pennsylvanian) in Daviess County, Indiana. The Lower Block Coal Member ranges in thickness from 51 to 74 cm and the Upper Block Coal Member ranges from 20 to 65 cm. Average sulfur content and ash yield of the Lower Block coal (0.98%, 7.65%) are lower than in the Upper Block coal. Megascopically, the coals show distinct differences. The Lower Block is a banded coal with numerous thin fusain horizons and a thin clay parting in the lower third of the seam. The Upper Block coal has a dulling-upward trend, with a bright clarain found at the base that grades into a clarain and then into a durain in the upper portion of the seam. Vitrinite content of the Lower Block coal ranges from 63% to 78%, with the highest vitrinite content found in the middle portion of the seam. In the Upper Block coal, vitrinite content ranges from 40% to 83%, with the highest values found in the lower part of the seam. Ash yield is higher in the upper part of the Upper Block coal, reaching up to 40%. The Lower Block coal is dominated by lycopod trees and tree ferns. The Upper Block coal shows marked differences in spore assemblages between lower and upper parts of the seam. The lower half is dominated by large lycopod trees and tree ferns, similar to the Lower Block coal. The upper half is dominated by small lycopods, mainly Densosporites and Radiizonates. These differences between the Lower Block and Upper Block Coal members are significant correlation tools applicable to mining exploration and chronostratigraphy.

Method for reducing NOx during combustion of coal in a burner

DOEpatents

Zhou, Bing [Cranbury, NJ; Parasher, Sukesh [Lawrenceville, NJ; Hare, Jeffrey J [Provo, UT; Harding, N Stanley [North Salt Lake, UT; Black, Stephanie E [Sandy, UT; Johnson, Kenneth R [Highland, UT

2008-04-15

An organically complexed nanocatalyst composition is applied to or mixed with coal prior to or upon introducing the coal into a coal burner in order to catalyze the removal of coal nitrogen from the coal and its conversion into nitrogen gas prior to combustion of the coal. This process leads to reduced NOx production during coal combustion. The nanocatalyst compositions include a nanoparticle catalyst that is made using a dispersing agent that can bond with the catalyst atoms. The dispersing agent forms stable, dispersed, nano-sized catalyst particles. The catalyst composition can be formed as a stable suspension to facilitate storage, transportation and application of the catalyst nanoparticles to a coal material. The catalyst composition can be applied before or after pulverizing the coal material or it may be injected directly into the coal burner together with pulverized coal.

Royal Society, Discussion on New Coal Chemistry, London, England, May 21, 22, 1980, Proceedings

NASA Astrophysics Data System (ADS)

1981-03-01

A discussion of new coal chemistry is presented. The chemical and physical structure of coal is examined in the first section, including structural studies of coal extracts, metal and metal complexes in coal and coal microporosity. The second section presents new advances in applied coal technology. The development of liquid fuels and chemicals from coal is given especial emphasis, with papers on the Sasol Synthol process, the Shell-Koppers gasification process, liquefaction and gasification in Germany, the Solvent Refined Coal process, the Exxon Donor Solvent liquefaction process and the Mobil Methanol-to-Gasoline process. Finally, some developments that will be part of the future of coal chemistry in the year 2000 are examined in the third section, including coal-based chemical complexes and the use of coal as an alternative source to oil for chemical feedstocks.

Model modifications for simulation of flow through stratified rocks in eastern Ohio

USGS Publications Warehouse

Helgesen, J.O.; Razem, A.C.; Larson, S.P.

1982-01-01

A quasi three-dimensional groundwater flow model is being used as part of a study to determine impacts of coal-strip mining on local hydrologic systems. Modifications to the model were necessary to simulate local hydrologic conditions properly. Perched water tables required that the method of calculating vertical flow rate be changed. A head-dependent spring-discharge function and a head-dependent stream aquifer-interchange function were added to the program. Modifications were also made to allow recharge from precipitation to any layer. The modified program, data deck instructions, and sample input and output are presented. (USGS)

A geochemical investigation into the effect of coal rank on the potential environmental effects of CO2 sequestration in deep coal beds

USGS Publications Warehouse

Kolak, Jonathan J.; Burruss, Robert A.

2005-01-01

Coal samples of different rank were extracted in the laboratory with supercritical CO2 to evaluate the potential for mobilizing hydrocarbons during CO2 sequestration or enhanced coal bed methane recovery from deep coal beds. The concentrations of aliphatic hydrocarbons mobilized from the subbituminous C, high-volatile C bituminous, and anthracite coal samples were 41.2, 43.1, and 3.11 ?g g-1 dry coal, respectively. Substantial, but lower, concentrations of polycyclic aromatic hydrocarbons (PAHs) were mobilized from these samples: 2.19, 10.1, and 1.44 ?g g-1 dry coal, respectively. The hydrocarbon distributions within the aliphatic and aromatic fractions obtained from each coal sample also varied with coal rank and reflected changes to the coal matrix associated with increasing degree of coalification. Bitumen present within the coal matrix may affect hydrocarbon partitioning between coal and supercritical CO2. The coal samples continued to yield hydrocarbons during consecutive extractions with supercritical CO2. The amount of hydrocarbons mobilized declined with each successive extraction, and the relative proportion of higher molecular weight hydrocarbons increased during successive extractions. These results demonstrate that the potential for mobilizing hydrocarbons from coal beds, and the effect of coal rank on this process, are important to consider when evaluating coal beds for CO2 storage.

13. Coal ejectors mounted on aft bulkhead of coal bunker. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. Coal ejectors mounted on aft bulkhead of coal bunker. Ejectors were used to flush overboard live coals and clinkers from firebed (pipe for carrying coals overboard has been removed from ejector in foreground). Coal doors from bunker appear beside ejector in foreground). Coal doors from bunker appear beside ejectors at deck; note firing shovels in background against hull. - Steamboat TICONDEROGA, Shelburne Museum Route 7, Shelburne, Chittenden County, VT

Clean coal initiatives in Indiana

USGS Publications Warehouse

Bowen, B.H.; Irwin, M.W.; Sparrow, F.T.; Mastalerz, Maria; Yu, Z.; Kramer, R.A.

2007-01-01

Purpose - Indiana is listed among the top ten coal states in the USA and annually mines about 35 million short tons (million tons) of coal from the vast reserves of the US Midwest Illinois Coal Basin. The implementation and commercialization of clean coal technologies is important to the economy of the state and has a significant role in the state's energy plan for increasing the use of the state's natural resources. Coal is a substantial Indiana energy resource and also has stable and relatively low costs, compared with the increasing costs of other major fuels. This indigenous energy source enables the promotion of energy independence. The purpose of this paper is to outline the significance of clean coal projects for achieving this objective. Design/methodology/approach - The paper outlines the clean coal initiatives being taken in Indiana and the research carried out at the Indiana Center for Coal Technology Research. Findings - Clean coal power generation and coal for transportation fuels (coal-to-liquids - CTL) are two major topics being investigated in Indiana. Coking coal, data compilation of the bituminous coal qualities within the Indiana coal beds, reducing dependence on coal imports, and provision of an emissions free environment are important topics to state legislators. Originality/value - Lessons learnt from these projects will be of value to other states and countries.

[Coal fineness effect on primary particulate matter features during pulverized coal combustion].

PubMed

Lü, Jian-yi; Li, Ding-kai

2007-09-01

Three kinds of coal differed from fineness were burned in a laboratory-scale drop tube furnace for combustion test, and an 8-stage Andersen particle impactor was employed for sampling the primary particulate matter (PM), in order to study coal fineness effect on primary PM features during pulverized coal combustion. It has been shown that the finer the coal was, the finer the PM produced. PM, emission amount augmented with coal fineness decreased, and the amount of PM10 increased from 13 mg/g to 21 mg/g respectively generated by coarse coal and fine coal. The amount of PM2.5 increased from 2 mg/g to 8 mg/g at the same condition. Constituents and content in bulk ash varied little after three different fineness coal combustion, while the appearance of grading PM differed visibly. The value of R(EE) increased while the coal fineness deceased. The volatility of trace elements which were investigated was Pb > Cr > Zn > Cu > Ni in turn. The concentration of poisonous trace elements was higher which generated from fine coal combustion. The volatilization capacity was influenced little by coal fineness, but the volatilization extent was influenced differently by coal fineness. Fine coal combustion affects worse environment than coarse coal does.

The Republic of the Philippines coalbed methane assessment: based on seventeen high pressure methane adsorption isotherms

USGS Publications Warehouse

Flores, Romeo M.; Stricker, Gary D.; Papasin, Ramon F.; Pendon, Ronaldo R.; del Rosario, Rogelio A.; Malapitan, Ruel T.; Pastor, Michael S.; Altomea, Elmer A.; Cuaresma, Federico; Malapitan, Armando S.; Mortos, Benjamin R.; Tilos, Elizabeth N.

2006-01-01

Introduction: The Republic of the Philippines has some 19 coal districts that contain coal deposits ranging from Eocene to Pleistocene in age. These coal districts include: (1) Catanduanes (Eocene); (2) Cebu, Zamboanga Sibuguey, Bukidnon, Maguindanao, Sarangani, and Surigao (Oligocene to Miocene); (3) Batan Island, Masbate, Semirara (including Mindoro), and Quezon-Polilio (lower-upper Miocene); (4) Davao, Negros, and Sorsogon (middle-upper Miocene); (5) Cotabato (lower Miocene-lower Pliocene), Cagayan-Isabella, and Quirino (upper Miocene-Pliocene); (6) Sultan Kudarat (upper Miocene-Pleistocene); and (7) Samar-Leyte (lower Pliocene-Pleistocene). In general, coal rank is directly related to the age of the deposits - for example, the Eocene coal is semi-anthracite and the Pliocene-Pleistocene coal is lignite. Total coal resources in these 19 coal districts, which are compiled by the Geothermal and Coal Resources Development Division (GCRDD) of the Department of Energy of the Philippines, are estimated at a minimum of 2,268.4 million metric tonnes (MMT) (approximately 2.3 billion metric tones). The largest resource (550 MMT) is the subbituminous coal in the Semirara (including Mindoro) coal district, and the smallest (0.7 MMT) is the lignite-subbituminous coal in the Quirino coal district. The combined lignite and subbituminous coal resources, using the classification by GCRDD and including Semirara and Surigao coal districts, are about 1,899.2 MMT, which make up about 84 percent of the total coal resources of the Philippines. The remaining resources are composed of bituminous and semi-anthracite coal. The subbituminous coal of Semirara Island in the Mindoro- Semirara coal district (fig. 2) is known to contain coalbed methane (CBM), with the coal being comparable in gas content and adsorption isotherms to the coal of the Paleocene Fort Union Formation in the Powder River Basin in Wyoming, USA (Flores and others, 2005). As a consequence, the presence of CBM in the Semirara coal led to the present study of determining the adsorption isotherms, or gas (CBM) holding or storage capacity, of coal beds of various ages from selected coal districts in the Philippines. Samples for the study were collected from the Batan Island, Catanduanes, Cagayan-Isabella, Cebu, Negros, Samar, Semirara, Cotabato, Surigao, and Malangas coalfield of the Zamboanga Sibuguey coal districts by five field geology teams from the GCRDD.

Coal-fired power generaion, new air quality regulations, and future U.S. coal production

USGS Publications Warehouse

Attanasi, E.D.; Root, D.H.

1999-01-01

Tighter new regulation of stack gas emissions and competition in power generation are driving electrical utilities to demand cleaner, lower sulfur coal. Historical data on sulfur content of produced coals shows little variability in coal quality for individual mines and individual coal-producing counties over relatively long periods of time. If coal-using power generators follow the compliance patterns established in Phase I of the 1990 Clean Air Act Amendments, then the industry's response to the tighter Phase II emissions standards will result in large amounts of coal production shifting from higher sulfur areas to areas with lower cost low sulfur coal. One reason this shift will likely occur is that currently only 30% of U.S. coal-fired electrical generating capacity is equipped with flue-gas scrubbers. In 1995, coal mines in the higher sulfur areas of the Illinois Basin and Northern and Central Appalachia employed 78% of all coal miners (>70,000 miners). A substantial geographical redistribution of the nation's coal supplies will likely lead to economic dislocations that will reach beyond local coal-producing areas.

Methane Content Estimation in DuongHuy Coal Mine

NASA Astrophysics Data System (ADS)

Nguyen, Van Thinh; Mijał, Waldemar; Dang, Vu Chi; Nguyen, Thi Tuyet Mai

2018-03-01

Methane hazard has always been considered for underground coal mining as it can lead to methane explosion. In Quang Ninh province, several coal mines such as Mạo Khe coal mine, Khe Cham coal mine, especially Duong Huy mine that have high methane content. Experimental data to examine contents of methane bearing coal seams at different depths are not similar in Duong coal mine. In order to ensure safety, this report has been undertaken to determine a pattern of changing methane contents of coal seams at different exploitation depths in Duong Huy underground coal mine.

Interaction of coal-derived synthesis gas impurities with solid oxide fuel cell metallic components

NASA Astrophysics Data System (ADS)

Marina, Olga A.; Pederson, Larry R.; Coyle, Christopher A.; Edwards, Danny J.; Chou, Yeong-Shyung; Cramer, Carolyn N.

Oxidation-resistant alloys find use as interconnect materials, heat exchangers, and gas supply tubing in solid oxide fuel cell (SOFC) systems, especially when operated at temperatures below ∼800 °C. If fueled with synthesis gas derived from coal or biomass, such metallic components could be exposed to impurities contained in those fuel sources. In this study, coupons of ferritic stainless steels Crofer 22 APU and SS 441, austenitic nickel-chromium superalloy Inconel 600, and an alumina-forming high nickel alloy alumel were exposed to synthesis gas containing ≤2 ppm phosphorus, arsenic and antimony, and reaction products were tested. Crofer 22 APU coupons coated with a (Mn,Co) 3O 4 protective layer were also evaluated. Phosphorus was found to be the most reactive. On Crofer 22 APU, the (Mn,Cr) 3O 4 passivation layer reacted to form an Mn-P-O product, predicted to be manganese phosphate from thermochemical calculations, and Cr 2O 3. On SS 441, reaction of phosphorus with (Mn,Cr) 3O 4 led to the formation of manganese phosphate as well as an Fe-P product, predicted from thermochemical calculations to be Fe 3P. Minimal interactions with antimony or arsenic in synthesis gas were limited to Fe-Sb and Fe-As solid solution formation. Though not intended for use on the anode side, a (Mn,Co) 3O 4 spinel coating on Crofer 22 APU reacted with phosphorus in synthesis gas to produce products consistent with Mn 3(PO 4) 2 and Co 2P. A thin Cr 2O 3 passivation layer on Inconel 600 did not prevent the formation of nickel phosphides and arsenides and of iron phosphides and arsenides, though no reaction with Cr 2O 3 was apparent. On alumel, an Al 2O 3 passivation layer rich in Ni did not prevent the formation of nickel phosphides, arsenides, and antimonides, though no reaction with Al 2O 3 occurred. This work shows that unprotected metallic components of an SOFC stack and system can provide a sink for P, As and Sb impurities that may be present in fuel gases, and thus complicate experimental studies of impurity interactions with the anode.

U.S. Geological Survey coal quality (COALQUAL) database; version 2.0

USGS Publications Warehouse

Bragg, L.J.; Oman, J.K.; Tewalt, S.J.; Oman, C.L.; Rega, N.H.; Washington, P.M.; Finkelman, R.B.

1997-01-01

The USGS Coal Quality database is an interactive, computerized component of the NCRDS. It contains comprehensive analyses of more than 13,000 samples of coal and associated rocks from every major coal-bearing basin and coal bed in the U.S. The data in the coal quality database represent analyses of the coal as it exists in the ground. The data commonly are presented on an as-received whole-coal basis.

Process for preparing a stabilized coal-water slurry

DOEpatents

Givens, E.N.; Kang, D.

1987-06-23

A process is described for preparing a stabilized coal particle suspension which includes the steps of providing an aqueous media substantially free of coal oxidizing constituents, reducing, in a nonoxidizing atmosphere, the particle size of the coal to be suspended to a size sufficiently small to permit suspension thereof in the aqueous media and admixing the coal of reduced particle size with the aqueous media to release into the aqueous media coal stabilizing constituents indigenous to and carried by the reduced coal particles in order to form a stabilized coal particle suspension. The coal stabilizing constituents are effective in a nonoxidizing atmosphere to maintain the coal particle suspension at essentially a neutral or alkaline pH. The coal is ground in a nonoxidizing atmosphere such as an inert gaseous atmosphere to reduce the coal to a sufficient particle size and is admixed with an aqueous media that has been purged of oxygen and acid-forming gases. 2 figs.

Process for preparing a stabilized coal-water slurry

DOEpatents

Givens, Edwin N.; Kang, Doohee

1987-01-01

A process for preparing a stabilized coal particle suspension which includes the steps of providing an aqueous media substantially free of coal oxidizing constituents, reducing, in a nonoxidizing atmosphere, the particle size of the coal to be suspended to a size sufficiently small to permit suspension thereof in the aqueous media and admixing the coal of reduced particle size with the aqueous media to release into the aqueous media coal stabilizing constituents indigenous to and carried by the reduced coal particles in order to form a stabilized coal particle suspension. The coal stabilizing constituents are effective in a nonoxidizing atmosphere to maintain the coal particle suspension at essentially a neutral or alkaline pH. The coal is ground in a nonoxidizing atmosphere such as an inert gaseous atmosphere to reduce the coal to a sufficient particle size and is admixed with an aqueous media that has been purged of oxygen and acid-forming gases.

Trace elements in coal. Environmental and health significance

USGS Publications Warehouse

Finkelman, R.B.

1999-01-01

Trace elements can have profound adverse effects on the health of people burning coal in homes or living near coal deposits, coal mines, and coal- burning power plants. Trace elements such as arsenic emitted from coal- burning power plants in Europe and Asia have been shown to cause severe health problems. Perhaps the most widespread health problems are caused by domestic coal combustion in developing countries where millions of people suffer from fluorosis and thousands from arsenism. Better knowledge of coal quality characteristics may help to reduce some of these health problems. For example, information on concentrations and distributions of potentially toxic elements in coal may help delineate areas of a coal deposit to be avoided. Information on the modes of occurrence of these elements and the textural relations of the minerals in coal may help to predict the behavior of the potentially toxic trace metals during coal cleaning, combustion, weathering, and leaching.

Mössbauer study of the inorganic sulfur removal from coals

NASA Astrophysics Data System (ADS)

Reyes Caballero, F.; Martínez Ovalle, S. A.

2014-01-01

Mössbauer Spectroscopy (MS) was applied to study the occurrence and behavior of the iron-sulfur-containing minerals in coal and coal fractions obtained by different separation methods: hydrocyclonic, flotation and chemical removal process. Samples of one high sulfur coal from Guachinte mine (Valle, Colombia) and three low sulfur coals from the El Salitre zone (Paipa-Boyacá, Colombia) were analyzed. MS evidenced only the presence of pyrite in Esmeralda and Las Casitas coals, while it identified pyrite and siderite on Cerezo coal. MS and SEM- EDX confirm the inorganic sulfur removal on Guachinte coal submitted to hydrocyclonic removal process. MS of the precipitated coal fraction from Las Casitas mine obtained by flotation in water showed the presence of ferrous sulfate because of coal-weathering process. Treatment with hot diluted HNO3 equal to 27 acid on raw coal sample from Las Casitas mine showed that almost all of the pyrite in raw coal was removed.

Geological and geochemical characteristics of high arsenic coals from endemic arsenosis areas in southwestern Guizhou Province, China

USGS Publications Warehouse

Ding, Z.; Zheng, B.; Long, J.; Belkin, H.E.; Finkelman, R.B.; Chen, C.; Zhou, D.; Zhou, Y.

2001-01-01

Southwest Guizhou Province is one of the most important areas of disseminated, sediment-hosted-type Au deposits in China and is an important area of coal production. The chemistry of most of the coals in SW Guizhou is similar to those in other parts of China. Their As content is near the Chinese coal average, but some local, small coal mines contain high As coals. The highest As content is up to 3.5 wt.% in the coal. The use of high As coals has caused in excess of 3000 cases of As poisoning in several villages. The high As coals are in the Longtan formation, which is an alternating marine facies and terrestrial facies. The coals are distributed on both sides of faults that parallel the regional anticlinal axis. The As content of coal is higher closer to the fault plane. The As content of coal changes greatly in different coal beds and different locations of the same bed. Geological structures such as anticlines, faults and sedimentary strata control the distribution of high As coals. Small Au deposits as well as Sb, Hg, and Th mineralization, are found near the high As coals. Although some As-bearing minerals such as pyrite, arsenopyrite, realgar (?), As-bearing sulfate, As-bearing clays, and phosphate are found in the high As coals, their contents cannot account for the abundance of As in some coals. Analysis of the coal indicates that As mainly exists in the form of As5+ and As3+, perhaps, combined with organic compounds. The occurrence of such exceptionally high As contents in coal and the fact that the As is dominantly organically associated are unique observations. ?? 201 Elsevier Science Ltd.

Application studies of RFID technology in the process of coal logistics transport

NASA Astrophysics Data System (ADS)

Qiao, Bingqin; Chang, Xiaoming; Hao, Meiyan; Kong, Dejin

2012-04-01

For quality control problems in coal transport, RFID technology has been proposed to be applied to coal transportation process. The whole process RFID traceability system from coal production to consumption has been designed and coal supply chain logistics tracking system integration platform has been built, to form the coal supply chain traceability and transport tracking system and providing more and more transparent tracking and monitoring of coal quality information for consumers of coal. Currently direct transport and combined transport are the main forms of coal transportation in China. The means of transport are cars, trains and ships. In the booming networking environment of RFID technology, the RFID technology will be applied to coal logistics and provide opportunity for the coal transportation tracking in the process transportation.

Chemical composition and some trace element contents in coals and coal ash from Tamnava-Zapadno Polje Coal Field, Serbia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vukasinovic-Pesic, V.; Rajakovic, L.J.

2009-07-01

The chemical compositions and trace element contents (Zn, Cu, Co, Cr, Ni, Pb, Cd, As, B, Hg, Sr, Se, Be, Ba, Mn, Th, V, U) in coal and coal ash samples from Tamnava-Zapadno Polje coal field in Serbia were studied. The coal from this field belongs to lignite. This high volatility coal has high moisture and low S contents, moderate ash yield, and high calorific value. The coal ash is abundant in alumosilicates. Many trace elements such as Ni > Cd > Cr > B > As > Cu > Co > Pb > V > Zn > Mn inmore » the coal and Ni > Cr > As > B > Cu > Co = Pb > V > Zn > Mn in the coal ash are enriched in comparison with Clarke concentrations.« less

43 CFR 3436.1-2 - Federal coal deposits subject to lease by exchange.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Federal coal deposits subject to lease by... Coal Lease and Coal Land Exchanges: Alluvial Valley Floors § 3436.1-2 Federal coal deposits subject to... Federal coal deposits determined to be acceptable for further consideration for coal leasing pursuant to...

Development of coal-feeding systems at the Morgantown Energy Research Center

NASA Technical Reports Server (NTRS)

Hobday, J. M.

1977-01-01

Systems for feeding crushed and pulverized coal into coal conversion reactor vessels are described. Pneumatic methods for feeding pulverized coal, slurry feeders, and coal pumps, methods for steam pickup, and a method for drying a water-coal slurry in a steam fluidized bed subsequent to feeding the coal into a reactor vessel are included.

Modeling the Use of Mine Waste Rock as a Porous Medium Reservoir for Compressed Air Energy Storage

NASA Astrophysics Data System (ADS)

Donelick, R. A.; Donelick, M. B.

2016-12-01

We are studying the engineering and economic feasibilities of constructing Big Mass Battery (BiMBy) compressed air energy storage devices using some of the giga-tonnes of annually generated and historically produced mine waste rock/overburden/tailings (waste rock). This beneficial use of waste rock is based on the large mass (Big Mass), large pore volume, and wide range of waste rock permeabilities available at some large open pit metal mines and coal strip mines. Porous Big Mass is encapsulated and overlain by additional Big Mass; compressed air is pumped into the encapsulated pore space when renewable energy is abundant; compressed air is released from the encapsulated pore space to run turbines to generate electricity at the grid scale when consumers demand electricity. Energy storage capacity modeling: 1) Yerington Pit, Anaconda Copper Mine, Yerington, NV (inactive metal mine): 340 Mt Big Mass, energy storage capacity equivalent to 390k-710k home batteries of size 10 kW•h/charge, assumed 20% porosity, 50% overall efficiency. 2) Berkeley Pit, Butte Copper Mine, Butte, MT (inactive metal mine): 870 Mt Big Mass, energy storage capacity equivalent to 1.4M-2.9M home batteries of size 10 kW•h/charge, assumed 20% porosity, 50% overall efficiency. 3) Rosebud Mine, Colstrip, MT (active coal strip mine): 87 Mt over 2 years, energy storage capacity equivalent to 45k-67k home batteries of size 10 kW•h/charge, assumed 30% porosity, 50% overall efficiency. Encapsulating impermeable layer modeling: Inactive mine pits like Yerington Pit and Berkeley Pit, and similar active pits, have associated with them low permeability earthen material (silt and clay in Big Mass) at sufficient quantities to manufacture an encapsulating structure with minimal loss of efficiency due to leakage, a lifetime of decades or even centuries, and minimal need for the use of geomembranes. Active coal strip mines like Rosebud mine have associated with them low permeability earthen material such as coal combustion products (fly ash, bottom ash, boiler slag, other) that may be put to beneficial use as part of the encapsulating structure; however, coal strip mines have lower volume to surface ratios than mine pits increasing the potential need to use geomembranes.

Physico-chemical and optical properties of combustion-generated particles from coal-fired power plant, automobile and ship engine and charcoal kiln.

NASA Astrophysics Data System (ADS)

Kim, Hwajin

2015-04-01

Similarities and differences in physico-chemical and optical properties of combustion generated particles from various sources were investigated. Coal-fired power plant, charcoal kiln, automobile and ship engine were major sources, representing combustions of coal, biomass and two different types of diesel, respectively. Scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and energy-dispersive X-ray spectroscopy (EDX) equipped with both SEM and HRTEM were used for physico-chemical analysis. Light absorbing properties were assessed using a spectrometer equipped with an integrating sphere. Particles generated from different combustion sources and conditions demonstrate great variability in their morphology, structure and composition. From coal-fired power plant, both fly ash and flue gas were mostly composed of heterogeneously mixed mineral ash spheres, suggesting that the complete combustion was occurred releasing carbonaceous species out at high temperature (1200-1300 °C). Both automobile and ship exhausts from diesel combustions show typical features of soot: concentric circles comprised of closely-packed graphene layers. However, heavy fuel oil (HFO) combusted particles from ship exhaust demonstrate more complex compositions containing different morphology of particles other than soot, e.g., spherical shape of char particles composed of minerals and carbon. Even for the soot aggregates, particles from HFO burning have different chemical compositions; carbon is dominated but Ca (29.8%), S (28.7%), Na(1%), and Mg(1%) are contained, respectively which were not found from particles of automobile emission. This indicates that chemical compositions and burning conditions are significant to determine the fate of particles. Finally, from biomass burning, amorphous and droplet-like carbonaceous particles with no crystallite structure are observed and they are generally formed by the condensation of low volatile species at low-temperature (~300-800 °C) combustion conditions. Depending on burning sources, significantly different optical properties were observed; diesel combustion particles from automobile and ship showed wavelength independent absorbing properties whereas the particles from coal and charcoal kiln combustion showed the enhanced absorption at shorter wavelength which is a brown carbon characteristic. Our findings suggest that source dependent properties and distributions across the globe should be considered when their impacts on climate change and air qualities are discussed.

Method of extracting coal from a coal refuse pile

DOEpatents

Yavorsky, Paul M.

1991-01-01

A method of extracting coal from a coal refuse pile comprises soaking the coal refuse pile with an aqueous alkali solution and distributing an oxygen-containing gas throughout the coal refuse pile for a time period sufficient to effect oxidation of coal contained in the coal refuse pile. The method further comprises leaching the coal refuse pile with an aqueous alkali solution to solubilize and extract the oxidized coal as alkali salts of humic acids and collecting the resulting solution containing the alkali salts of humic acids. Calcium hydroxide may be added to the solution of alkali salts of humic acid to form precipitated humates useable as a low-ash, low-sulfur solid fuel.

Cytotoxicity and genotoxicity induced by coal and coal fly ash particles samples in V79 cells.

PubMed

León-Mejía, Grethel; Silva, Luis F O; Civeira, Matheus S; Oliveira, Marcos L S; Machado, Miriana; Villela, Izabel Vianna; Hartmann, Andreas; Premoli, Suziane; Corrêa, Dione Silva; Da Silva, Juliana; Henriques, João Antônio Pêgas

2016-12-01

Exposure to coal and coal ashes can cause harmful effects in in vitro and in vivo systems, mainly by the induction of oxidative damage. The aim of this work was to assess cytotoxic and genotoxic effects using the V79 cell line treated with coal and coal fly ash particles derived from a coal power plant located in Santa Catarina, Brazil. Two coal samples (COAL11 and COAL16) and two coal fly ash samples (CFA11 and CFA16) were included in this study. COAL16 was co-firing with a mixture of fuel oil and diesel oil. The comet assay data showed that exposure of V79 cells to coal and coal fly ash particles induced primary DNA lesions. Application of lesion-specific endonucleases (FPG and ENDO III) demonstrated increased DNA effects indicating the presence of high amounts of oxidative DNA lesions. The cytokinesis-block micronucleus cytome assay analysis showed that exposure of V79 cells to high concentrations of coal and coal fly ash particles induced cytotoxic effects (apoptosis and necrosis) and chromosomal instability (nucleoplasmic bridges, nuclear buds, and micronucleus (MN) formation). These results may be associated with compounds contained in the surface of the particles as hazardous elements, ultrafine/nanoparticles, and polycyclic aromatic hydrocarbons (PAHs) which were detected in the samples. Graphical abstract ᅟ.

Flash pyrolysis of coal, coal maceral, and coal-derived pyrite with on-line characterization of volatile sulfur compounds

USGS Publications Warehouse

Chou, I.-Ming; Lake, M.A.; Griffin, R.A.

1988-01-01

A Pyroprobe flash pyrolysis-gas chromatograph equipped with a flame photometric detector was used to study volatile sulfur compounds produced during the thermal decomposition of Illinois coal, coal macerals and coal-derived pyrite. Maximum evolution of volatile organic sulfur compounds from all coal samples occurred at a temperature of approximately 700??C. At this temperature, the evolution of thiophene, its alkyl isomers, and short-chain dialkyl sulfide compounds relative to the evolution of benzothiophene and dibenzothiophene compounds was greater from coal high in organic sulfur than from coal low in organic sulfur. The variation in the evolution of sulfur compounds observed for three separate coal macerals (exinite, vitrinite, and inertinite) was similar to that observed for whole coal samples. However, the variation trend for the macerals was much more pronounced. Decomposition of coal-derived pyrite with the evolution of elemental sulfur was detected at a temperature greater than 700??C. The results of this study indicated that the gas chromotographic profile of the volatile sulfur compounds produced during flash pyrolysis of coals and coal macerals varied as a function of the amount of organic sulfur that occurred in the samples. Characterization of these volatile sulfur compounds provides a better understanding of the behavior of sulfur in coal during the thermolysis process, which could be incorporated in the design for coal cleaning using flash pyrolysis techniques. ?? 1988.

Occurrence and mobility of toxic elements in coals from endemic fluorosis areas in the Three Gorges Region, SW China.

PubMed

Xiong, Yan; Xiao, Tangfu; Liu, Yizhang; Zhu, Jianming; Ning, Zengping; Xiao, Qingxiang

2017-10-01

Fluorine (F) is a topic of great interest in coal-combustion related endemic fluorosis areas. However, little extent research exists regarding the environmental geochemistry of toxic elements that are enriched in coals and coal wastes in traditional endemic fluorosis areas, particularly focusing on their occurrences and mobilities during the weathering-leaching processes of coals and coal wastes in the surface environment. This paper addressed the issue of toxic elements in coals and coal wastes in the Three Gorges Region, Southwest (SW) China, where endemic fluorosis has historically prevailed, and investigated the distribution, occurrence, mobility features, and associated potential health risks. For this purpose, a modified experiment combined with long-term humidity cell test and column leaching trial was applied to elucidate the mobility of toxic elements in coals and coal wastes. In addition, sequential chemical extraction (SCE) was used to ascertain the modes of occurrence of toxic elements. The results demonstrated that the contents of toxic elements in the study area followed the order: stone coals > gangues > coal balls > coals. Furthermore, modes of occurrence of toxic elements were obviously different in coals and coal wastes. For example, cadmium (Cd) was mainly associated with monosulfide fraction in coals, molybdenum (Mo) and arsenic (As) were mainly associated with carbonate and silicate in coal gangues and stone coals, chromium (Cr) mainly existed in silicate and insoluble matter in coal gangues and coal balls, thallium (Tl) mainly occurred in organic matter in stone coals and sulfide in coals, and the occurrence of antimony (Sb) varied with different kinds of samples. Moreover, a large amount of toxic elements released to the leachates during the weathering and leaching process, which might pollute the environment and threaten human health. Based on the geo-accumulation index (I geo ), single factor index (P i ) and Nemerow index (P N ), soils i n the study area were mainly polluted by Cd, which constituted a potential risk to locally planted crops. Copyright © 2017 Elsevier Inc. All rights reserved.

Phyto-bioconversion of hard coal in the Cynodon dactylon/coal rhizosphere.

PubMed

Igbinigie, Eric E; Mutambanengwe, Cecil C Z; Rose, Peter D

2010-03-01

Fundamental processes involved in the microbial degradation of coal and its derivatives have been well documented. A mutualistic interaction between plant roots and certain microorganisms to aid growth of plants such as Cynodon dactylon (Bermuda grass) on hard coal dumps has recently been suggested. In the present study coal bioconversion activity of nonmycorrhizal fungi was investigated in the C. dactylon/coal rhizosphere. Fungal growth on 2% Duff-agar, gutation formation on nitric acid treated coal and submerged culture activity in nitrogen-rich and -deficient broth formed part of the screening and selection of the fungi. The selected fungal isolates were confirmed to be found in pristine C. dactylon/coal rhizosphere. To simulate bioconversion, a fungal aliquot of this rhizosphere was used as inoculum for a Perfusate fixed bed bioreactor, packed with coal. The results demonstrate an enhanced coal bioconversion facilitated by low molecular weight organics and the bioconversion of coal may be initiated by an introduction of nitrogen moieties to the coal substrate. These findings suggest a phyto-bioconversion of hard coal involving plant and microbes occurring in the rhizosphere to promote the growth of C. dactylon. An understanding of this relationship can serve as a benchmark for coal dumps rehabilitation as well as for the industrial scale bioprocessing of hard coal.

Coal-Quality Information - Key to the Efficient and Environmentally Sound Use of Coal

USGS Publications Warehouse

Finkleman, Robert B.

1997-01-01

The rock that we refer to as coal is derived principally from decomposed organic matter (plants) consisting primarily of the element carbon. When coal is burned, it produces energy in the form of heat, which is used to power machines such as steam engines or to drive turbines that produce electricity. Almost 60 percent of the electricity produced in the United States is derived from coal combustion. Coal is an extraordinarily complex material. In addition to organic matter, coal contains water (up to 40 or more percent by weight for some lignitic coals), oils, gases (such as methane), waxes (used to make shoe polish), and perhaps most importantly, inorganic matter (fig. 1). The inorganic matter--minerals and trace elements--cause many of the health, environmental, and technological problems attributed to coal use (fig. 2). 'Coal quality' is the term used to refer to the properties and characteristics of coal that influence its behavior and use. Among the coal-quality characteristics that will be important for future coal use are the concentrations, distribution, and forms of the many elements contained in the coal that we intend to burn. Knowledge of these quality characteristics in U.S. coal deposits may allow us to use this essential energy resource more efficiently and effectively and with less undesirable environmental impact.

Influence of high-energy impact on the physical and technical characteristics of coal fuels

NASA Astrophysics Data System (ADS)

Mal'tsev, L. I.; Belogurova, T. P.; Kravchenko, I. V.

2017-08-01

Currently, in the world's large-scale coal-fired power industry, the combustion of pulverized coal is the most widely spread technology of combusting the coals. In recent years, the micropulverization technology for preparation and combustion of the coal has been developed in this field. As applied to the small-scale power industry, the method of combusting the coal in the form of a coal-water slurry has been explored for years. Fine coal powders are produced and used in the pulverized-coal gasification. Therefore, the coal preparation methods that involve high-dispersion disintegration of coals attract the greatest interest. The article deals with the problems of high-energy impact on the coal during the preparation of pulverized-coal fuels and coal-water slurries, in particular, during the milling of the coal in ball drum mills and the subsequent regrinding in disintegrators or the cavitation treatment of the coal-water slurries. The investigations were conducted using samples of anthracite and lignite from Belovskii open-pit mine (Kuznetsk Basin). It is shown that both the disintegration and the cavitation treatment are efficient methods for controlling the fuel characteristics. Both methods allow increasing the degree of dispersion of the coal. The content of the small-sized particles reground by cavitation considerably exceeds the similar figure obtained using the disintegrator. The specific surface area of the coal is increased by both cavitation and disintegration with the cavitation treatment producing a considerably greater effect. Being subjected to the cavitation treatment, most coal particles assume the form of a split characterized by the thermodynamically nonequilibrium state. Under external action, in particular, of temperature, the morphological structure of such pulverized materials changes faster and, consequently, the combustion of the treated coal should occur more efficiently. The obtained results are explained from the physical point of view.

Managing Security in FPGA-Based Embedded Systems

DTIC Science & Technology

2008-01-01

Trans. De- sign Automation of Electronic Systems (TODAES), vol. 13, no. 3, July 2008, article 44. c©2008 ACM with permission.5) of the function would need...in the finished design. In addition, the life cycle can be subverted when engineers inject unintended functionality, some of which might be malicious...cores and a moat size of two. There are several different drawbridge configurations between the cores. (IOB: I/O block; CLB: configuration logic block

Tumor-derived exosomes modulate T cell function through transfer of RNA.

PubMed

House, Imran G; Petley, Emma V; Beavis, Paul A

2018-03-01

Tumor cells can develop a variety of mechanisms to evade and subvert the immune system for their survival. Bland et al., in this edition of The FEBS Journal, make the novel finding that the tumor line B16F0 can deliver mRNA/miRNA loaded exosomes to cytotoxic T lymphocytes and alter their metabolic function and interferon gamma production. © 2018 Federation of European Biochemical Societies.

Coal pump development phase 3

NASA Technical Reports Server (NTRS)

Kushida, R. O.; Sankur, V. D.; Gerbracht, F. G.; Mahajan, V.

1980-01-01

Techniques for achieving continuous coal sprays were studied. Coazial injection with gas and pressure atomization were studied. Coal particles, upon cooling, were found to be porous and fragile. Reactivity tests on the extruded coal showed overall conversion to gases and liquids unchanged from that of the raw coal. The potentials for applications of the coal pump to eight coal conversion processes were examined.

Fuel Gas Demonstration Plant Program: Small-Scale Industrial Project. Coal procurement activities. Technica report No. 9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-04-14

This report consists of reference material taken from Erie Mining Company project files and includes the following: (1) Investigation of the Main Coal Producing Fields in the United States: This report identifies potential coal fiels for gasifier feedstock and factors influencing coal selection. The report analyzes coal fields located in five separate regions of the United States. Three design coals are discussed and lab reports have been included. Also included are cost considerations for selected coals and preliminary cost data and transportation routing. (2) Analysis of Test Coals Received at Erie Mining Company: Rosebud, Clarion, and Clarion-Brookfield-Kittaning coal samples weremore » received and analyzed at Erie Mining Company. The screen analysis indicated the severe decrepitation of the Rosebud western coal. (3) Criteria for Gasifier Coal: In this study, BCI states that gasifier feed should have the following characteristics: (1) the ratio between the upper and lower size for coal should be 3:1; (2) coal fines should not exceed 10%; (3) coal grading limits which can be handled are maximum range 3'' x 1'', minimum range - 1 1/2'' x 1/2''.« less

Abundances of polycyclic aromatic hydrocarbons (PAHs) in 14 chinese and american coals and their relation to coal rank and weathering

USGS Publications Warehouse

Wang, R.; Liu, Gaisheng; Zhang, Jiahua; Chou, C.-L.; Liu, J.

2010-01-01

The abundances of 16 polycyclic aromatic hydrocarbons (PAHs) on the priority list of the United States Environmental Protection Agency (U.S. EPA) have been determined in 14 Chinese and American coals. The ranks of the samples range from lignite, bituminous coal, anthracite, to natural coke. Soxhlet extraction was conducted on each coal for 48 h. The extract was analyzed on a gas chromatograph-mass spectrometer (GC-MS). The results show that the total PAH content ranged from 0.31 to 57.6 ??g/g of coal (on a dry basis). It varied with coal rank and is highest in the maturity range of bituminous coal rank. High-molecular-weight (HMW) PAHs are predominant in low-rank coals, but low-molecular-weight (LMW) PAHs are predominant in high-rank coals. The low-sulfur coals have a higher PAH content than high-sulfur coals. It may be explained by an increasing connection between disulfide bonds and PAHs in high-sulfur coal. In addition, it leads us to conclude that the PAH content of coals may be related to the depositional environment. ?? 2010 American Chemical Society.

The US Geological Survey's national coal resource assessment: The results

USGS Publications Warehouse

Ruppert, Leslie F.; Kirschbaum, Mark A.; Warwick, Peter D.; Flores, Romeo M.; Affolter, Ronald H.; Hatch, Joseph R.

2002-01-01

The US Geological Survey and the State geological surveys of many coal-bearing States recently completed a new assessment of the top producing coal beds and coal zones in five major producing coal regions—the Appalachian Basin, Gulf Coast, Illinois Basin, Colorado Plateau, and Northern Rocky Mountains and Great Plains. The assessments, which focused on both coal quality and quantity, utilized geographic information system technology and large databases. Over 1,600,000 million short tons of coal remain in over 60 coal beds and coal zones that were assessed. Given current economic, environmental, and technological restrictions, the majority of US coal production will occur in that portion of the assessed coal resource that is lowest in sulfur content. These resources are concentrated in parts of the central Appalachian Basin, Colorado Plateau, and the Northern Rocky Mountains.

Energy Crunch is Stimulant for Coal Research

ERIC Educational Resources Information Center

Chemical and Engineering News, 1973

1973-01-01

Presents views of the first International Coal Research Conference, involving problems facing reconversion to a coal-based energy economy, organization and funding of coal research units, development of new techniques for mining and using coal; and transportation of coal products to users. (CC)

Quarterly Coal Distribution

EIA Publications

2017-01-01

The Quarterly Coal Distribution Report (QCDR) provides detailed U.S. domestic coal distribution data by coal origin state, coal destination state, mode of transportation, and consuming sector. Quarterly data for all years are preliminary and will be superseded by the release of the corresponding Annual Coal Distribution Report.

GIS representation of coal-bearing areas in Antarctica

USGS Publications Warehouse

Merrill, Matthew D.

2016-03-11

Understanding the distribution of coal-bearing geologic units in Antarctica provides information that can be used in sedimentary, geomorphological, paleontological, and climatological studies. This report is a digital compilation of information on Antarctica’s coal-bearing geologic units found in the literature. It is intended to be used in small-scale spatial geographic information system (GIS) investigations and as a visual aid in the discussion of Antarctica’s coal resources or in other coal-based geologic investigations. Instead of using spatially insignificant point markers to represent large coal-bearing areas, this dataset uses polygons to represent actual coal-bearing lithologic units. Specific locations of coal deposits confirmed from the literature are provided in the attribution for the coal-bearing unit polygons. Coal-sample-location data were used to confirm some reported coal-bearing geology. The age and extent of the coal deposits indicated in the literature were checked against geologic maps ranging from local scale at 1:50,000 to Antarctic continental scale at 1:5,000,000; if satisfactory, the map boundaries were used to generate the polygons for the coal-bearing localities.

Non-classical types of loess

NASA Astrophysics Data System (ADS)

Iriondo, M. H.; Kröhling, D. M.

2007-12-01

The purpose of this contribution is to describe the sequence of physical and chemical processes resulting in the sediment-type named loess, a fine-grained sediment deposit of universal occurrence. Owing to historical causes, loess has been (and still is) implicitly linked to glacial/periglacial environments among most naturalists. However it is known today that most eolian dust is deflated from tropical deserts. Hence, that sequence of processes is more comprehensive than the former narrow cold scenario. Six examples of different "non-classical" cases (from South America and Europe) that fit well to the loess definition are developed: 1) volcanic loess in Ecuador: pyroclastic eruptions/valley wind/mountain praire/silica structuring; 2) tropical loess in northeastern Argentina, Brazil and Uruguay: deflation of river and fan splays/savanna/iron sesquioxide structuring; 3) gypsum loess in northern Spain: destruction of anhydrite/gypsiferous layers in a dry climate/valley wind/Saharian shrub peridesert/gypsum structuring; 4) trade-wind deposits in Venezuela and Brazil: deflation in tidal flats/trade wind into the continent/savanna/iron hydroxide structuring; 5) anticyclonic gray loess in Argentina: continental anticyclone on plains/anti-clockwise winds and whirls/steppe/carbonate structuring. All these non-classical types conform to the accepted loess definitions and they also share the most important field characteristics of loess such as grain size, friability, vertical or sub-vertical slopes in outcrops, subfusion and others. Other cases can probably be recognized when systematically scrutinized.

The World Coal Quality Inventory: South America

USGS Publications Warehouse

Karlsen, Alex W.; Tewalt, Susan J.; Bragg, Linda J.; Finkelman, Robert B.

2006-01-01

Executive Summary-Introduction: The concepts of a global environment and economy are strongly and irrevocably linked to global energy issues. Worldwide coal production and international coal trade are projected to increase during the next several decades in an international energy mix that is still strongly dependent on fossil fuels. Therefore, worldwide coal use will play an increasingly visible role in global environmental, economic, and energy forums. Policy makers require information on coal, including coal quality data, to make informed decisions regarding domestic coal resource allocation, import needs and export opportunities, foreign policy objectives, technology transfer policies, foreign investment prospects, environmental and health assessments, and byproduct use and disposal issues. The development of a worldwide, reliable, coal quality database would help ensure the most economically and environmentally efficient global use of coal. The U.S. Geological Survey (USGS), in cooperation with many agencies and scientists from the world's coal producing countries, originally undertook a project to obtain representative samples of coal from most of the world's producing coal provinces during a limited period of time (roughly 1998-2005), which is called the World Coal Quality Inventory (WoCQI). The multitude of producing coal mines, coal occurrences, or limited accessibility to sites in some countries can preclude collecting more than a single sample from a mine. In some areas, a single sample may represent an entire coal mining region or basin. Despite these limitations in sampling and uneven distribution of sample collection, the analytical results can still provide a general overview of world coal quality. The USGS intends to present the WoCQI data in reports and, when possible, in Geographic Information System (GIS) products that cover important coal bearing and producing regions.

Characteristics of Pyrolytic Topping in Fluidized Bed for Different Volatile Coals

NASA Astrophysics Data System (ADS)

Xiong, R.; Dong, L.; Xu, G. W.

Coal is generally combusted or gasified directly to destroy completely the chemical structures, such as aromatic rings containing in volatile coals including bituminite and lignite. Coal topping refers to a process that extracts chemicals with aromatic rings from such volatile coals in advance of combustion or gasification and thereby takes advantage of the value of coal as a kind of chemical structure resource. CFB boiler is the coal utilization facility that can be easily retrofitted to implement coal topping. A critical issue for performing coal topping is the choice of the pyrolytic reactor that can be different types. The present study concerns fluidized bed reactor that has rarely been tested for use in coal topping. Two different types of coals, one being Xiaolongtan (XLT) lignite and the other Shanxi (SX) bituminous, were tested to clarify the yield and composition of pyrolysis liquid and gas under conditions simulating actual operations. The results showed that XLT lignite coals had the maximum tar yield in 823-873K and SX bituminite realized its highest tar yield in 873-923K. Overall, lignite produced lower tar yield than bituminous coal. The pyrolysis gas from lignite coals contained more CO and CO2 and less CH4, H2 and C2+C3 (C2H4, C2H6, C3H6, C3H8) components comparing to that from bituminous coal. TG-FTIR analysis of tars demonstrated that for different coals there are different amounts of typical chemical species. Using coal ash of CFB boiler, instead of quartz sand, as the fluidized particles decreased the yields of both tar and gas for all the tested coals. Besides, pyrolysis in a reaction atmosphere simulating the pyrolysis gas (instead of N2) resulted also in higher production of pyrolysis liquid.

Update on coal in Big Horn basin, Montana and Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, R.W.

1983-08-01

The Big Horn Coal basin is located within the topographic and structural basin of the same name and is defined by the limits of the Upper Cretaceous Mesaverde Formation in northwestern Wyoming and the Eagle Sandstone in south-central Montana. The coal in this basin ranges in rank from high volatile C bituminous (based primarily on resistance to weathering) to subbituminous B coal. In general, the Mesaverde and Eagle coals are highest in heat content, averaging over 10,500 Btu/lb; the Fort Union coals in the Red Lodge-Bear Creek and Grass Creek fields average about 10,200 Btu/lb and are second highest inmore » heating value. The Meeteetse Formation contains coals that average 9,800 Btu/lb, the lowest heating values in the basin. An average heating value for all coal in the basin is slightly less than 10,000 But/lb. The average sulfur content of all coals in this basin is less than 1%, with a range of 0.4 to 2.2%. Coal mining in the Big Horn Coal basin began in the late 1880s in the Red Lodge field and has continued to the present. Almost 53 million tons of coal have been mined in the basin; nearly 78% of this production (41 million tons) is from bituminous Fort Union coal beds in the Red Lodge-Bear Creek and Bridger coal fields, Montana. Original in-place resources for the Big Horn Coal basin are given by rank of coal: 1,265.12 million tons of bituminous coal resources have been calculated for the Silvertip field, Wyoming, and the Red Lodge-Bear Creek and Bridger fields, Montana; 563.78 million tons of subbituminous resources have been calculated for the remaining Wyoming coal fields.« less

The environmental impact of future coal production and use in the EEC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1983-01-01

The aims of this study are to assess the expected increased levels of coal consumption in the European Community up to the year 2000; to estimate to what extent consumer demand is likely to be met by EEC production; to determine the level of polluting emissions which are likely to derive from changes in coal consumption and production; and finally, to compare the environmental impact of alternative, existing or developing means of coal utilisation. Contents: Conclusions; Future coal supply and demand in the EEC; Environmental consequences of coal production and use; Coal extraction; Transport and storage; Coal combustion: air pollution;more » Coal combustion: water pollution; Pollution from solid wastes; Coal conversion process; Environmental control technology; Bibliography.« less

Rosebud SynCoal Partnership, SynCoal{reg_sign} demonstration technology update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheldon, R.W.

1997-12-31

An Advanced Coal Conversion Process (ACCP) technology being demonstrated in eastern Montana (USA) at the heart of one of the world`s largest coal deposits is providing evidence that the molecular structure of low-rank coals can be altered successfully to produce a unique product for a variety of utility and industrial applications. The product is called SynCoal{reg_sign} and the process has been developed by the Rosebud SynCoal Partnership (RSCP) through the US Department of Energy`s multi-million dollar Clean Coal Technology Program. The ACCP demonstration process uses low-pressure, superheated gases to process coal in vibrating fluidized beds. Two vibratory fluidized processing stagesmore » are used to heat and convert the coal. This is followed by a water spray quench and a vibratory fluidized stage to cool the coal. Pneumatic separators remove the solid impurities from the dried coal. There are three major steps to the SynCoal{reg_sign} process: (1) thermal treatment of the coal in an inert atmosphere, (2) inert gas cooling of the hot coal, and (3) removal of ash minerals. When operated continuously, the demonstration plant produces over 1,000 tons per day (up to 300,000 tons per year) of SynCoal{reg_sign} with a 2% moisture content, approximately 11,800b Btu/lb and less than 1.0 pound of SO{sub 2} per million Btu. This product is obtained from Rosebud Mine sub-bituminous coal which starts with 25% moisture, 8,600 Btu/lb and approximately 1.6 pounds of SO{sub 2} per million Btu.« less

30 CFR 772.13 - Coal exploration compliance duties.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Coal exploration compliance duties. 772.13... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR COAL EXPLORATION § 772.13 Coal exploration compliance duties. (a) All...

30 CFR 772.13 - Coal exploration compliance duties.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal exploration compliance duties. 772.13... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR COAL EXPLORATION § 772.13 Coal exploration compliance duties. (a) All...

30 CFR 772.13 - Coal exploration compliance duties.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Coal exploration compliance duties. 772.13... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR COAL EXPLORATION § 772.13 Coal exploration compliance duties. (a) All...

30 CFR 772.13 - Coal exploration compliance duties.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Coal exploration compliance duties. 772.13... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR COAL EXPLORATION § 772.13 Coal exploration compliance duties. (a) All...

Microbial solubilization of coal

DOEpatents

Strandberg, G.W.; Lewis, S.N.

1988-01-21

The present invention relates to a cell-free preparation and process for the microbial solubilization of coal into solubilized coal products. More specifically, the present invention relates to bacterial solubilization of coal into solubilized coal products and a cell-free bacterial byproduct useful for solubilizing coal. 5 tabs.

30 CFR 772.13 - Coal exploration compliance duties.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Coal exploration compliance duties. 772.13... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR COAL EXPLORATION § 772.13 Coal exploration compliance duties. (a) All...

Simulated coal spill causes mortality and growth inhibition in tropical marine organisms.

PubMed

Berry, Kathryn L E; Hoogenboom, Mia O; Flores, Florita; Negri, Andrew P

2016-05-13

Coal is a principal fossil fuel driving economic and social development, and increases in global coal shipments have paralleled expansion of the industry. To identify the potential harm associated with chronic marine coal contamination, three taxa abundant in tropical marine ecosystems (the coral Acropora tenuis, the reef fish Acanthochromis polyacanthus and the seagrass Halodule uninervis) were exposed to five concentrations (0-275 mg coal l(-1)) of suspended coal dust (<63 μm) over 28 d. Results demonstrate that chronic coal exposure can cause considerable lethal effects on corals, and reductions in seagrass and fish growth rates. Coral survivorship and seagrass growth rates were inversely related to increasing coal concentrations (≥38 mg coal l(-1)) and effects increased between 14 and 28 d, whereas fish growth rates were similarly depressed at all coal concentrations tested. This investigation provides novel insights into direct coal impacts on key tropical taxa for application in the assessment of risks posed by increasing coal shipments in globally threatened marine ecosystems.

An update on blast furnace granular coal injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, D.G.; Strayer, T.J.; Bouman, R.W.

1997-12-31

A blast furnace coal injection system has been constructed and is being used on the furnace at the Burns Harbor Division of Bethlehem Steel. The injection system was designed to deliver both granular (coarse) and pulverized (fine) coal. Construction was completed on schedule in early 1995. Coal injection rates on the two Burns Harbor furnaces were increased throughout 1995 and was over 200 lbs/ton on C furnace in September. The injection rate on C furnace reached 270 lbs/ton by mid-1996. A comparison of high volatile and low volatile coals as injectants shows that low volatile coal replaces more coke andmore » results in a better blast furnace operation. The replacement ratio with low volatile coal is 0.96 lbs coke per pound of coal. A major conclusion of the work to date is that granular coal injection performs very well in large blast furnaces. Future testing will include a processed sub-bituminous coal, a high ash coal and a direct comparison of granular versus pulverized coal injection.« less

Carbon dioxide from coal combustion: Variation with rank of US coal

USGS Publications Warehouse

Quick, J.C.; Glick, D.C.

2000-01-01

Carbon dioxide from combustion of US coal systematically varies with ASTM rank indices, allowing the amount of CO2 produced per net unit of energy to be predicted for individual coals. No single predictive equation is applicable to all coals. Accordingly, we provide one equation for coals above high volatile bituminous rank and another for lower rank coals. When applied to public data for commercial coals from western US mines these equations show a 15% variation of kg CO2 (net GJ)-1. This range of variation suggests reduction of US CO2 emissions is possible by prudent selection of coal for combustion. Maceral and mineral content are shown to slightly affect CO2 emissions from US coal. We also suggest that CO2 emissions increased between 6 and 8% in instances where Midwestern US power plants stopped burning local, high-sulfur bituminous coal and started burning low-sulfur, subbituminous C rank coal from the western US.

Simulated coal spill causes mortality and growth inhibition in tropical marine organisms

NASA Astrophysics Data System (ADS)

Berry, Kathryn L. E.; Hoogenboom, Mia O.; Flores, Florita; Negri, Andrew P.

2016-05-01

Coal is a principal fossil fuel driving economic and social development, and increases in global coal shipments have paralleled expansion of the industry. To identify the potential harm associated with chronic marine coal contamination, three taxa abundant in tropical marine ecosystems (the coral Acropora tenuis, the reef fish Acanthochromis polyacanthus and the seagrass Halodule uninervis) were exposed to five concentrations (0-275 mg coal l-1) of suspended coal dust (<63 μm) over 28 d. Results demonstrate that chronic coal exposure can cause considerable lethal effects on corals, and reductions in seagrass and fish growth rates. Coral survivorship and seagrass growth rates were inversely related to increasing coal concentrations (≥38 mg coal l-1) and effects increased between 14 and 28 d, whereas fish growth rates were similarly depressed at all coal concentrations tested. This investigation provides novel insights into direct coal impacts on key tropical taxa for application in the assessment of risks posed by increasing coal shipments in globally threatened marine ecosystems.

Raman spectral characteristics of magmatic-contact metamorphic coals from Huainan Coalfield, China

NASA Astrophysics Data System (ADS)

Chen, Shancheng; Wu, Dun; Liu, Guijian; Sun, Ruoyu

2017-01-01

Normal burial metamorphism of coal superimposed by magmatic-contact metamorphism makes the characteristics of the Raman spectrum of coal changed. Nine coal samples were chosen at a coal transect perpendicular to the intrusive dike, at the No. 3 coal seam, Zhuji Coal Mine, Huainan Coalfield, China, with different distances from dike-coal boundary (DCB). Geochemical (proximate and ultimate) analysis and mean random vitrinite reflectance (R0, %) indicate that there is a significant relationship between the values of volatile matter and R0 in metamorphosed coals. Raman spectra show that the graphite band (G band) becomes the major band but the disordered band (D band) disappears progressively, with the increase of metamorphic temperature in coals, showing that the structural organization in high-rank contact-metamorphosed coals is close to that of well-crystallized graphite. Evident relationships are observed between the calculated Raman spectral parameters and the peak metamorphic temperature, suggesting some spectral parameters have the potentials to be used as geothermometers for contact-metamorphic coals.

Coal Combustion Science quarterly progress report, April--June 1992. Task 1, Coal devolatilization: Task 2, Coal char combustion; Task 3, Fate of mineral matter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hardesty, D.R.; Hurt, R.H.; Baxter, L.L.

1992-09-01

The objective of this work is to support the Office of Fossil Energy in executing research on coal combustion science. This project consists of basic research on coal combustion that supports both the Pittsburgh Energy Technology Center (PETC) Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency (IEA) Coal Combustion Science Project. Specific tasks include: The characterization of the physical and chemical processes that constitute the early devolatilization phase of coal combustion: Characterization of the combustion behavior of selected coals under conditions relevant to industria pulverized coal-fired furnaces; and to establish a quantitative understanding of themore » mechanisms and rates of transformation, fragmentation, and deposition of mineral matter in coal combustion environments as a function of coal type, particle size and temperature, the initial forms and distributions of mineral species in the unreacted coal, and the local gas temperature and composition.« less

Filtering coal-derived oil through a filter media precoated with particles partially solubilized by said oil

DOEpatents

Rodgers, Billy R.; Edwards, Michael S.

1977-01-01

Solids such as char, ash, and refractory organic compounds are removed from coal-derived liquids from coal liquefaction processes by the pressure precoat filtration method using particles of 85-350 mesh material selected from the group of bituminous coal, anthracite coal, lignite, and devolatilized coals as precoat materials and as body feed to the unfiltered coal-derived liquid.

Influence of Geological Structure on Coal and Gas Outburst Occurrences in Turkish Underground Coal Mines

NASA Astrophysics Data System (ADS)

Esen, Olgun; Özer, Samet Can; Fişne, Abdullah

2015-04-01

Coal and gas outbursts are sudden and violent releases of gas and in company with coal that result from a complex function of geology, stress regime with gas pressure and gas content of the coal seam. The phenomena is referred to as instantaneous outbursts and have occurred in virtually all the major coal producing countries and have been the cause of major disasters in the world mining industry. All structures from faults to joints and cleats may supply gas or lead to it draining away. Most geological structures influence the way in which gas can drain within coal seams. From among all the geological factors two groups can be distinguished: parameters characterising directly the occurrence and geometry of the coal seams; parameters characterising the tectonic disturbances of the coal seams and neighbouring rocks. Also dykes may act as gas barriers. When the production of the coal seam is advanced in mine working areas, these barriers are failed mostly in the weak and mylonitized zones. Geology also plays a very important role in the outburst process. Coal seams of complex geological structure including faults, folds, and fractured rocks are liable to outbursts if coal seams and neighbouring rocks have high gas content level. The purpose of the study is to enlighten the coal industry in Turkey to improving mine safety in underground coal production and decrease of coal and gas outburst events due to increasing depth of mining process. In Turkey; the years between 1969 and 2013, the number of 90 coal and gas outbursts took place in Zonguldak Hard Coal Basin in both Kozlu and Karadon Collieries. In this study the liability to coal and gas outburst of the coal seams are investigated by measuring the strength of coal and the rock pressure. The correlation between these measurements and the event locations shows that the geological structures resulted in 52 events out of 90 events; 19 events close to the fault zones, 25 events thorough the fault zones and 8 events in the zones where sudden changes of inclination and/or thickness of the coal seam.

Oxidation and carbonisation of coals: a case study of coal fire affected coals from the Wuda coalfield, Inner Mongolia, China

NASA Astrophysics Data System (ADS)

Kus, Jolanta; Meyer, Uwe; Ma, Jianwei; Chen-Brauchler, Dai

2010-05-01

At the coalfield of Wuda (Inner Mongolia, PR China) extensive underground coal fires cause widespread thermal and oxidative effects in coal seams. Within phase B of the Coal Fire Research Project of the Sino-German Initiative, methods for innovative fire-extinguishing technologies were investigated in multifaceted research approaches. Extensive investigations of oxidative and thermally affected coal seams in coal fire zone 18 were conducted in 2008 prior to application of new fire-extinguishing methods. We present results from the outcrop of coal seam No. 4 in the fire zone 18. The coal of seam No. 4 is of Early Permian age and belongs stratigraphically to the Shanxi Formation. The unaffected coal displays a high volatile bituminous A rank with a background value of random vitrinite reflectance ranging from 0.90 to 0.96 % Rr. Coal channel samples were coallected at actively extracted coal faces along multiple profiles with surface temperatures ranging from about 50° to 600°C. Microscopic examinations revealed a variety of products of coal exposure to the fire. Within coal samples, a marked rise in vitrinite reflectance from background values to 5.55% Rr (6.00 % Rmax) is encountered. In addition, a number of coal samples showed suppressed vitrinite reflectances ranging between 0.82 to 0.88% Rr. Further, seemingly heat unaffected coal samples display intensive development of oxidations rims at coal grain edges and cracks as well as shrinkage cracks and formation of iron oxides/hydroxides. Instead, thermally affected coal samples with higher coalification grade are further characterised by development of macropores (devolatilisation pores) in vitrinitic streaks, transformation of liptinite to meta-liptinite and micrinite as well as by natural coke particles of mostly porous nature and fine to coarse grained anisotropic mosaic. Coal petrographic investigations confirmed a hypothesis that both, oxidations as well as low temperature carbonisation govern the thermal regime in the coal fire zone 18. The occurrence of various thermal alteration products indicates temperatures in the range of 500-700°C.

Geology, coal quality, and resources of the Antaramut-Kurtan-Dzoragukh coal field, north-central Armenia

USGS Publications Warehouse

Pierce, B.S.; Martirosyan, A.; Malkhasian, G.; Harutunian, S.; Harutunian, G.

2001-01-01

The Antaramut-Kurta-Dzoragukh (AKD) coal deposit is a previously unrecognized coal field in north-central Armenia. Coal has been known to exist in the general vicinity since the turn of the century, but coal was thought to be restricted to a small (1 km2) area only near the village of Antaramut. However, through detailed field work and exploratory drilling, this coal deposit has been expanded to at least 20 km2, and thus renamed the Antaramut-Kurtan-Dzoragukh coal field, for the three villages that the coal field encompasses. The entire coal-bearing horizon, a series of tuffaceous sandstones, siltstones, and claystones, is approximately 50 m thick. The AKD coal field contains two coal beds, each greater than 1 m thick, and numerous small rider beds, with a total resource of approximately 31,000,000 metric tonnes. The coals are late Eocene in age, high volatile bituminous in rank, relatively high in ash yield (approximately 40%, as-determined basis) and moderate in sulfur content (approximately 3%, as-determined basis). The two coal beds (No. 1 and No. 2), on a moist, mineral-matter-free basis, have high calorific values of 32.6 MJ/kg (7796 cal/g) and 36.0 MJ/kg (8599 cal/g), respectively. Coal is one of the few indigenous fossil fuel resources occurring in Armenia and thus, the AKD coal field could potentially provide fuel for heating and possibly energy generation in the Armenian energy budget. Published by Elsevier Science B.V.

Is there an association of circulatory hospitalizations independent of mining employment in coal-mining and non-coal-mining counties in west virginia?

PubMed

Talbott, Evelyn O; Sharma, Ravi K; Buchanich, Jeanine; Stacy, Shaina L

2015-04-01

Exposures associated with coal mining activities, including diesel fuel exhaust, products used in coal processing, and heavy metals and other forms of particulate matter, may impact the health of nearby residents. We investigated the relationships between county-level circulatory hospitalization rates (CHRs) in coal and non-coal-mining communities of West Virginia, coal production, coal employment, and sociodemographic factors. Direct age-adjusted CHRs were calculated using West Virginia hospitalizations from 2005 to 2009. Spatial regressions were conducted to explore associations between CHR and total, underground, and surface coal production. After adjustment, neither total, nor surface, nor underground coal production was significantly related to rate of hospitalization for circulatory disease. Our findings underscore the significant role sociodemographic and behavioral factors play in the health and well-being of coal mining communities.

77 FR 22607 - Notice of Competitive Coal Lease Sale, Wyoming

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-16

...] Notice of Competitive Coal Lease Sale, Wyoming AGENCY: Bureau of Land Management, Interior. ACTION: Notice. SUMMARY: Notice is hereby given that certain coal resources in the South Porcupine Coal Tract..., Coal Coordinator, at 307-775-6258, and 307-775-6206, respectively. SUPPLEMENTARY INFORMATION: This coal...

Mercury in Eastern Kentucky coals: Geologic aspects and possible reduction strategies

USGS Publications Warehouse

Hower, J.C.; Eble, C.F.; Quick, J.C.

2005-01-01

Mercury emissions from US coal-fired power plants will be regulated by the US Environmental Protection Agency (USEPA) before the end of the decade. Because of this, the control of Hg in coal is important. Control is fundamentally based on the knowledge of the amounts of Hg in mined, beneficiated, and as-fired coal. Eastern Kentucky coals, on a reserve district level, have Hg contents similar to the USA average for coal at mines. Individual coals show greater variation at the bench scale, with Hg enrichment common in the top bench, often associated with enhanced levels of pyritic sulfur. Some of the variation between parts of eastern Kentucky is also based on the position relative to major faults. The Pine Mountain thrust fault appears to be responsible for elemental enrichment, including Hg, in coals on the footwall side of the thrust. Eastern Kentucky coals shipped to power plants in 1999, the year the USEPA requested coal quality information on coal deliveries, indicate that coals shipped from the region have 0.09 ppm Hg, compared to 0.10 ppm for all delivered coals in the USA. On an equal energy basis, and given equal concentrations of Hg, the high volatile bituminous coals from eastern Kentucky would emit less Hg than lower rank coals from other USA regions. ?? 2005 Elsevier B.V. All rights reserved.

Chlorine in coal and its relationship with boiler corrosion. Technical report, 1 March--31 May 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chou, M.I.M.; Lytle, J.M.; Ruch, R.R.

1994-09-01

Limited literature and use history data have suggested that some high-chlorine Illinois coals do not cause boiler corrosion while extensive data developed by the British correlate corrosion with chlorine content and other parameters related to the coal and boiler. The differences in corrosivity in coals may be due to the coal properties, to blending of coals, or to the boiler parameters in which they were burned. The goals of this study focus on coal properties. In this quarter, both destructive temperature-programmed Thermogravimetry with Fourier transform infrared (TGA-FTIR) and non-destructive X-ray absorption near-edge structure (XANES) techniques were used to examine themore » forms and the evolution characteristics of chlorine in coals. The TGA-FTIR results indicate that under oxidation condition, both British and Illinois coals release hydrogen chloride gas. Illinois coals release the gas at high temperature with maximum evolution temperature ranged between 210 and 280 C. The XANES results indicate that chlorine in coal exists in ionic forms including a solid salt form. The solid NaCl salt form, however, is observed only in some of the British coals and none of the Illinois coals. These results combined with TGA-FTIR results suggest that the chlorine ions in Illinois coals are different from the chlorine ions in British coals.« less

Chemistry of thermally altered high volatile bituminous coals from southern Indiana

USGS Publications Warehouse

Walker, R.; Mastalerz, Maria; Brassell, S.; Elswick, E.; Hower, J.C.; Schimmelmann, A.

2007-01-01

The optical properties and chemical characteristics of two thermally altered Pennsylvanian high volatile bituminous coals, the non-coking Danville Coal Member (Ro = 0.55%) and the coking Lower Block Coal Member (Ro = 0.56%) were investigated with the purpose of understanding differences in their coking behavior. Samples of the coals were heated to temperatures of 275????C, 325????C, 375????C and 425????C, with heating times of up to one hour. Vitrinite reflectance (Ro%) rises with temperature in both coals, with the Lower Block coal exhibiting higher reflectance at 375????C and 425????C compared to the Danville coal. Petrographic changes include the concomitant disappearance of liptinites and development of vesicles in vitrinites in both coals, although neither coal developed anisotropic coke texture. At 375????C, the Lower Block coal exhibits a higher aromatic ratio, higher reflectance, higher carbon content, and lower oxygen content, all of which indicate a greater degree of aromatization at this temperature. The Lower Block coal maintains a higher CH2/CH3 ratio than the Danville coal throughout the heating experiment, indicating that the long-chain unbranched aliphatics contained in Lower Block coal liptinites are more resistant to decomposition. As the Lower Block coal contains significant amounts of liptinite (23.6%), the contribution of aliphatics from these liptinites appears to be the primary cause of its large plastic range and high fluidity. ?? 2006 Elsevier B.V. All rights reserved.

Characterization and Recovery of Rare Earths from Coal and By-Products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Granite, Evan J.; Roth, Elliot; Alvin, Mary Anne

Coal is a precious resource, both in the United States and around the world. The United States has a 250-year supply of coal, and generates between 30 - 40% of its electricity through coal combustion. Approximately 1 Gt of coal has been mined annually in the US, although the 2015 total will likely be closer to 900 Mt (http://www.eia.gov/coal/production/quarterly/). Most of the coal is burned for power generation, but substantial quantities are also employed in the manufacture of steel, chemicals, and activated carbons. Coal has a positive impact upon many industries, including mining, power, rail transportation, manufacturing, chemical, steel, activatedmore » carbon, and fuels. Everything that is in the earth’s crust is also present within coal to some extent, and the challenge is always to utilize abundant domestic coal in clean and environmentally friendly manners. In the case of the rare earths, these valuable and extraordinarily useful elements are present within the abundant coal and coal by-products produced domestically and world-wide. These materials include the coals, as well as the combustion by-products such as ashes, coal preparation wastes, gasification slags, and mining by-products. All of these materials can be viewed as potential sources of rare earth elements. Most of the common inorganic lanthanide compounds, such as the phosphates found in coal, have very high melting, boiling, and thermal decomposition temperatures, allowing them to concentrate in combustion and gasification by-products. Furthermore, rare earths have been found in interesting concentrations in the strata above and below certain coal seams. Much of the recent research on coal utilization in the United States has focused upon the capture of pollutants such as acid gases, particulates, and mercury, and the greenhouse gas carbon dioxide. The possible recovery of rare earth and other critical elements from abundant coal and by-products is an exciting new research area, representing a dramatic paradigm shift for coal.« less

Preliminary report on methodology for calculating coal resources of the Wyodak-Anderson coal zone, Powder River basin, Wyoming and Montana

USGS Publications Warehouse

Ellis, Margaret S.; Gunther, Gregory L.; Flores, Romeo M.; Stricker, Gary D.; Ochs, Allan M.; Schuenemeyer, John H.

1998-01-01

The National Coal Resource Assessment of the Wyodak-Anderson coal zone includes reports on the geology, stratigraphy, quality, and quantity of coal. The calculation of resources is only one aspect of the assessment. Without thorough documentation of the coal resource study and the methods used, the results of our study could be misinterpreted. The task of calculating coal resources included many steps, the use of several commercial software programs, and the incorporation of custom programs. The methods used for calculating coal resources for the Wyodak-Anderson coal zone vary slightly from the methods used in other study areas, and by other workers in the National Coal Resource Assessment. The Wyodak-Anderson coal zone includes up to 10 coal beds in any given location. The net coal thickness of the zone at each data point location was calculated by summing the thickness of all of the coal beds that were greater than 2.5 ft thick. The amount of interburden is not addressed or reported in this coal resource assessment. The amount of overburden reported is the amount of rock above the stratigraphically highest coal bed in the zone. The resource numbers reported do not include coal within mine or lease areas, in areas containing mapped Wyodak-Anderson clinker, or in areas where the coal is extrapolated to be less than 2.5 ft thick. The resources of the Wyodak-Anderson coal zone are reported in Ellis and others (1998). A general description of how the resources were calculated is included in that report. The purpose of this report is to document in more detail some of the parameters and methods used, define our spatial data, compare resources calculated using different grid options and calculation methods, and explain the application of confidence limits to the resource calculation.

Reverse micelle synthesis of nanoscale metal containing catalysts. [Nickel metal (with a nickel oxide surface layer) and iron oxyhydroxide nanoscale powders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Darab, J.G.; Fulton, J.L.; Linehan, J.C.

1993-03-01

The need for morphological control during the synthesis of catalyst precursor powders is generally accepted to be important. In the liquefaction of coal, for example, iron-bearing catalyst precursor particles containing individual crystallites with diameters in the 1-100 nanometer range are believed to achieve good dispersion through out the coal-solvent slurry during liquefaction 2 runs and to undergo chemical transformations to catalytically active iron sulfide phases. The production of the nanoscale powders described here employs the confining spherical microdomains comprising the aqueous phase of a modified reverse micelle (MRM) microemulsion system as nanoscale reaction vessels in which polymerization, electrochemical reduction andmore » precipitation of solvated salts can occur. The goal is to take advantage of the confining nature of micelles to kinetically hinder transformation processes which readily occur in bulk aqueous solution in order to control the morphology and phase of the resulting powder. We have prepared a variety of metal, alloy, and metal- and mixed metal-oxide nanoscale powders from appropriate MRM systems. Examples of nanoscale powders produced include Co, Mo-Co, Ni[sub 3]Fe, Ni, and various oxides and oxyhydroxides of iron. Here, we discuss the preparation and characterization of nickel metal (with a nickel oxide surface layer) and iron oxyhydroxide MRM nanoscale powders. We have used extended x-ray absorption fine structure (EXAFS) spectroscopy to study the chemical polymerization process in situ, x-ray diffraction (XRD), scanning and transmission electron microcroscopies (SEM and TEM), elemental analysis and structural modelling to characterize the nanoscale powders produced. The catalytic activity of these powders is currently being studied.« less

In-situ stress distribution and coalbed methane reservoir permeability in the Linxing area, eastern Ordos Basin, China

NASA Astrophysics Data System (ADS)

Ju, Wei; Shen, Jian; Qin, Yong; Meng, Shangzhi; Li, Chao; Li, Guozhang; Yang, Guang

2017-11-01

Understanding the distribution of in-situ stresses is extremely important in a wide range of fields such as oil and gas exploration and development, CO2 sequestration, borehole stability, and stress-related geohazards assessment. In the present study, the in-situ stress distribution in the Linxing area of eastern Ordos Basin, China, was analyzed based on well tested parameters. The maximum horizontal principal stress (S Hmax), minimum horizontal principal stress (S hmin), and vertical stress (S v ) were calculated, and they were linearly correlated with burial depth. In general, two types of in-situ stress fields were determined in the Linxing area: (i) the in-situ stress state followed the relation S v >S Hmax>S hmin in shallow layers with burial depths of less than about 940 m, indicating a normal faulting stress regime; (ii) the S Hmax magnitude increased conspicuously and was greater than the S v magnitude in deep layers with depths more than about 940 m, and the in-situ stress state followed the relation S Hmax>S v >S hmin, demonstrating a strike-slip faulting stress regime. The horizontal differential stress (S Hmax-S hmin) increased with burial depth, indicating that wellbore instability may be a potentially significant problem when drilling deep vertical wells. The lateral stress coefficient ranged from 0.73 to 1.08 with an average of 0.93 in the Linxing area. The coalbed methane (CBM) reservoir permeability was also analyzed. No obvious exponential relationship was found between coal permeability and effective in-situ stress magnitude. Coal permeability was relatively high under a larger effective in-situ stress magnitude. Multiple factors, including fracture development, contribute to the variation of CBM reservoir permeability in the Linxing area of eastern Ordos Basin.

Pilot-scale Limestone Emission Control (LEC) process: A development project. Volume 1, Main report and appendices A, B, C, and D: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prudich, M.E.; Appell, K.W.; McKenna, J.D.

ETS, Inc., a pollution consulting firm with headquarters in Roanoke, Virginia, has developed a dry, limestone-based flue gas desulfurization (FGD) system. This SO{sub 2} removal system, called Limestone Emission Control (LEC), can be designed for installation on either new or existing coal-fired boilers. In the LEC process, the SO{sub 2} in the flue gas reacts with wetted granular limestone that is contained in a moving bed. A surface layer of principally calcium sulfate (CaSO{sub 4}) is formed on the limestone. Periodic removal of this surface layer by mechanical agitation allows high utilization of the limestone granules. A nominal 5,000 acfmmore » LEC pilot plant has been designed, fabricated and installed on the slipstream of a 70,000 pph stoker boiler providing steam to Ohio University`s Athens, Ohio campus. A total of over 90 experimental trials have been performed using the pilot-scale moving-bed LEC dry scrubber as a part of this research project with run times ranging up to a high of 125 hours. SO{sub 2} removal efficiencies as high as 99.9% were achievable for all experimental conditions studied during which sufficient humidification was added to the LEC bed. The LEC process and conventional limestone scrubbing have been compared on an equatable basis using flue gas conditions that would be expected at the outlet of the electrostatic precipitator (ESP) of a 500 MW coal-fired power plant. The LEC was found to have a definite economic advantage in both direct capital costs and operating costs. Based on the success and findings of the present project, the next step in LEC process development will be a full-scale commercial demonstration unit.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sozen, A.; Arcaklioglu, E.

The main goal of this study is to develop the energy sources estimation equations in order to estimate the future projections and make correct investments in Turkey using artificial neural network (ANN) approach. It is also expected that this study will be helpful in demonstrating energy situation of Turkey in amount of EU countries. Basic energy indicators such as population, gross generation, installed capacity, net energy consumption, import, export are used in input layer of ANN. Basic energy sources such as coal, lignite, fuel-oil, natural gas and hydro are in output layer. Data from 1975 to 2003 are used tomore » train. Three years (1981, 1994 and 2003) are only used as test data to confirm this method. Also, in this study, the best approach was investigated for each energy sources by using different learning algorithms (scaled conjugate gradient (SCG) and Levenberg-Marquardt (LM)) and a logistic sigmoid transfer function in the ANN with developed software. The statistical coefficients of multiple determinations (R{sup 2}-value) for training data are equal to 0.99802, 0.99918, 0.997134, 0.998831 and 0.995681 for natural gas, lignite, coal, hydraulic, and fuel-oil, respectively. Similarly, these values for testing data are equal to 0.995623, 0.999456, 0.998545, 0.999236, and 0.99002. The best approach was found for lignite by SCG algorithm with seven neurons so mean absolute percentage error (MAPE) is equal to 1.646753 for lignite. According to the results, the future projections of energy indicators using ANN technique have been obviously predicted within acceptable errors. Apart from reducing the whole time required, the importance of the ANN approach is possible to find solutions that make energy applications more viable and thus more attractive to potential users.« less

30 CFR 1206.452 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Coal subject to royalties-general provisions... INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.452 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM pursuant to 43 CFR...

30 CFR 1206.253 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Coal subject to royalties-general provisions..., DEPARTMENT OF THE INTERIOR Natural Resources Revenue PRODUCT VALUATION Federal Coal § 1206.253 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM...

30 CFR 1206.452 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Coal subject to royalties-general provisions... INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.452 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM pursuant to 43 CFR...

Coal and Energy.

ERIC Educational Resources Information Center

Bryant, Reba; And Others

This teaching unit explores coal as an energy resource. Goals, student objectives, background information, and activity options are presented for each major section. The sections are: (1) an introduction to coal (which describes how and where coal was formed and explains the types of coal); (2) the mining of coal (including the methods and ways of…

30 CFR 1206.452 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Coal subject to royalties-general provisions... INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.452 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM pursuant to 43 CFR...

Fuel supply system and method for coal-fired prime mover

DOEpatents

Smith, William C.; Paulson, Leland E.

1995-01-01

A coal-fired gas turbine engine is provided with an on-site coal preparation and engine feeding arrangement. With this arrangement, relatively large dry particles of coal from an on-site coal supply are micro-pulverized and the resulting dry, micron-sized, coal particulates are conveyed by steam or air into the combustion chamber of the engine. Thermal energy introduced into the coal particulates during the micro-pulverizing step is substantially recovered since the so-heated coal particulates are fed directly from the micro-pulverizer into the combustion chamber.

Coal assessments and coal research in the Appalachian basin: Chapter D.4 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Tewalt, Susan J.; Ruppert, Leslie F.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

State geological surveys are concentrating on mapping and correlating coal beds and coal zones and studying CBM potential and production. Both State surveys and the USGS are researching the potential for carbon dioxide sequestration in unmined coal beds and other geologic reservoirs. In addition, the State geological surveys continue their long-term collaboration with the USGS and provide coal stratigraphic data to the National Coal Resources Data System (NCRDS).

Characterization of Coal Porosity for Naturally Tectonically Stressed Coals in Huaibei Coal Field, China

PubMed Central

Li, Xiaoshi; Hou, Quanlin; Li, Zhuo; Wei, Mingming

2014-01-01

The enrichment of coalbed methane (CBM) and the outburst of gas in a coal mine are closely related to the nanopore structure of coal. The evolutionary characteristics of 12 coal nanopore structures under different natural deformational mechanisms (brittle and ductile deformation) are studied using a scanning electron microscope (SEM) and low-temperature nitrogen adsorption. The results indicate that there are mainly submicropores (2~5 nm) and supermicropores (<2 nm) in ductile deformed coal and mesopores (10~100 nm) and micropores (5~10 nm) in brittle deformed coal. The cumulative pore volume (V) and surface area (S) in brittle deformed coal are smaller than those in ductile deformed coal which indicates more adsorption space for gas. The coal with the smaller pores exhibits a large surface area, and coal with the larger pores exhibits a large volume for a given pore volume. We also found that the relationship between S and V turns from a positive correlation to a negative correlation when S > 4 m2/g, with pore sizes <5 nm in ductile deformed coal. The nanopore structure (<100 nm) and its distribution could be affected by macromolecular structure in two ways. Interconversion will occur among the different size nanopores especially in ductile deformed coal. PMID:25126601

Preliminary report on coal resources of the Wyodak-Anderson coal zone, Powder River Basin, Wyoming and Montana

USGS Publications Warehouse

Ellis, Margaret S.; Gunther, Gregory L.; Flores, Romeo M.; Ochs, Allen M.; Stricker, Gary D.; Roberts, Steven B.; Taber, Thomas T.; Bader, Lisa R.; Schuenemeyer, John H.

1998-01-01

The National Coal Resource Assessment (NCRA) project by the U.S. Geological Survey is designed to assess US coal with the greatest potential for development in the next 20 to 30 years. Coal in the Wyodak-Anderson (WA) coal zone in the Powder River Basin of Wyoming and Montana is plentiful, clean, and compliant with EPA emissions standards. This coal is considered to be very desirable for development for use in electric power generation. The purpose of this NCRA study was to compile all available data relating to the Wyodak- Anderson coal, correlate the beds that make up the WA coal zone, create digital files pertaining to the study area and the WA coal, and produce a variety of reports on various aspects of the assessed coal unit. This report contains preliminary calculations of coal resources for the WA coal zone and is one of many products of the NCRA study. Coal resource calculations in this report were produced using both public and confidential data from many sources. The data was manipulated using a variety of commercially available software programs and several custom programs. A general description of the steps involved in producing the resource calculations is described in this report.

Drivers for the renaissance of coal

PubMed Central

Steckel, Jan Christoph; Edenhofer, Ottmar; Jakob, Michael

2015-01-01

Coal was central to the industrial revolution, but in the 20th century it increasingly was superseded by oil and gas. However, in recent years coal again has become the predominant source of global carbon emissions. We show that this trend of rapidly increasing coal-based emissions is not restricted to a few individual countries such as China. Rather, we are witnessing a global renaissance of coal majorly driven by poor, fast-growing countries that increasingly rely on coal to satisfy their growing energy demand. The low price of coal relative to gas and oil has played an important role in accelerating coal consumption since the end of the 1990s. In this article, we show that in the increasingly integrated global coal market the availability of a domestic coal resource does not have a statistically significant impact on the use of coal and related emissions. These findings have important implications for climate change mitigation: If future economic growth of poor countries is fueled mainly by coal, ambitious mitigation targets very likely will become infeasible. Building new coal power plant capacities will lead to lock-in effects for the next few decades. If that lock-in is to be avoided, international climate policy must find ways to offer viable alternatives to coal for developing countries. PMID:26150491

Metalliferous coals of the Westphalian A Joggins Formation, Cumberland basin, Nova Scotia, Canada: Petrology, geochemistry, and palynology

USGS Publications Warehouse

Hower, J.C.; Calder, J.H.; Eble, C.F.; Scott, A.C.; Robertson, J.D.; Blanchard, L.J.

2000-01-01

Five coals of Westphalian A (early Middle Pennsylvanian) age were sampled from the Joggins Formation section exposed along Chignecto Bay at Joggins, Nova Scotia. Coal beds along the bay were mined beginning in the early 17th century, yet there have been few detailed published investigation of the coal beds of this classic section. The lowermost coal, the Upper Coal 28 (Upper Fundy), is a high-vitrinite coal with a spore assemblage dominated by arboreous lycopsid spores with tree ferns subdominant. The upper portions of the coal bed have the highest ratio of well-preserved to poorly-preserved telinite of any of the coals investigated. Coal 19 ('clam coal') has 88% total vitrinite but, unlike the Fundy coal bed, the telinite has a poor preservation ratio and half the total vitrinite population comprises gelocollinite and vitrodetrinite. The latter coal bed is directly overlain by a basin-wide limestone bed. The Lower Kimberly coal shows good preservation of vitrinite with relatively abundant telinite among the total vitrinite. The Middle Kimberly coal, which underlies the tetrapod-bearing lycopsid trees found by Lyell and Dawson in 1852, exhibits an upward decrease in arboreous lycopod spores and an upward increase in the tree fern spore Punctatisporites minutus. Telinite preservation increases upwards in the Middle Kimberly but overall is well below the preservation ratio of the Upper Fundy coal bed. The coals all have high sulfur contents, yielding up to 13.7% total sulfur for the lower lithotype of the Upper Fundy coal bed. The Kimberly coals are not only high in total and pyritic sulfur, but also have high concentrations of chalcophile elements. Zinc, ranging up to 15,000 ppm (ash basis), is present as sphalerite in fusain lumens. Arsenic and lead each exceed 6000 ppm (ash basis) in separate lithotypes of the Kimberly coals. Together these data are consistent with elevated pH in planar mires. The source of the elemental enrichment in this presumed continental section is enigmatic. (C) 2000 Elsevier Science B.V. All rights reserved.Five coals of Westphalian A (early Middle Pennsylvanian) age were sampled from the Joggins Formation section exposed along Chigneto Bay at Joggins, Nova Scotia. All the coals were found to have high sulfur contents. Overall, the data obtained are consistent with elevated pH in planar mires.

Thermal surface characteristics of coal fires 1 results of in-situ measurements

NASA Astrophysics Data System (ADS)

Zhang, Jianzhong; Kuenzer, Claudia

2007-12-01

Natural underground coal fires are fires in coal seams occurring subsurface. The fires are ignited through a process named spontaneous combustion, which occurs based on a natural reaction but is usually triggered through human interaction. Coal mining activities expose coal to the air. This leads to the exothermal oxidation of the carbon in the coal with the air's oxygen to CO 2 and - under certain circumstances - to spontaneous combustion. Coal fires occur in many countries world wide - however, currently the Chinese coal mining industry faces the biggest problems with coal fires. Coal fires destroy the valuable resource coal and furthermore lead to many environmental degradation phenomena such as the deterioration of surrounding vegetation, land subsidence and the emission of toxic gasses (CO, N 2O). They additionally contribute to the emission of green house relevant gasses such as CO 2 and CH 4 to the atmosphere. In this paper we present thermal characteristics of coal fires as measured in-situ during a field campaign to the Wuda coal fire area in south-central Inner Mongolia, China. Thermal characteristics include temperature anomaly measurements at the surface, spatial surface temperature profiles of fire areas and unaffected background areas, diurnal temperature profiles, and temperature measurements inside of coal fire induced cracks in the overlying bedrock. For all the measurements the effects of uneven solar heating through influences of slope and aspect are considered. Our findings show that coal fires result in strong or subtle thermal surface anomalies. Especially the latter can easily be influenced by heating of the surrounding background material through solar influences. Temperature variation of background rocks with different albedo, slope, aspect or vegetation cover can substantially influence the detectability of thermal anomalies. In the worst case coal fire related thermal anomalies can be completely masked by solar patterns during the daytime. Thus, night-time analysis is the most suitable for thermal anomaly mapping of underground coal fires, although this is not always feasible. The heat of underground coal fires only progresses very slowly through conduction in the rock material. Anomalies of coal fires completely covered by solid unfractured bedrock are very weak and were only measured during the night. The thermal pattern of underground coal fires manifested on the surface during the daytime is thus the pattern of cracks and vents, which occur due to the volume loss underground and which support radiation and convective energy transport of hot gasses. Inside coal fire temperatures can hardly be measured and can only be recorded if the glowing coal is exposed through a wider crack in the overlaying bedrock. Direct coal fire temperatures measured ranged between 233 °C and 854 °C. The results presented can substantially support the planning of thermal mapping campaigns, analyses of coal fire thermal anomalies in remotely sensed data, and can provide initial and boundary conditions for coal fire related numerical modeling. In a second paper named "Thermal Characteristics of Coal Fires 2: results of measurements on simulated coal fires" [ Zhang J., Kuenzer C., Tetzlaff A., Oettl D., Zhukov B., Wagner W., 2007. Thermal Characteristics of Coal Fires 2: Result of measurements on simulated coal fires. Accepted for publication at Journal of Applied Geophysics. doi:10.1016/j.jappgeo.2007.08.003] we report about thermal characteristics of simulated coal fires simulated under simplified conditions. The simulated set up allowed us to measure even more parameters under undisturbed conditions — especially inside fire temperatures. Furthermore we could demonstrate the differences between open surface coal fires and covered underground coal fires. Thermal signals of coal fires in near range thermal remotely sensed imagery from an observing tower and from an airplane are presented and discussed.

YEAR 2 BIOMASS UTILIZATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher J. Zygarlicke

2004-11-01

This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammermore » mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from cofiring coal with waste paper, sunflower hulls, and wood waste showed a broad spectrum of chemical and physical characteristics, according to American Society for Testing and Materials (ASTM) C618 procedures. Higher-than-normal levels of magnesium, sodium, and potassium oxide were observed for the biomass-coal fly ash, which may impact utilization in cement replacement in concrete under ASTM requirements. Other niche markets for biomass-derived fly ash were explored. Research was conducted to develop/optimize a catalytic partial oxidation-based concept for a simple, low-cost fuel processor (reformer). Work progressed to evaluate the effects of temperature and denaturant on ethanol catalytic partial oxidation. A catalyst was isolated that had a yield of 24 mole percent, with catalyst coking limited to less than 15% over a period of 2 hours. In biodiesel research, conversion of vegetable oils to biodiesel using an alternative alkaline catalyst was demonstrated without the need for subsequent water washing. In work related to biorefinery technologies, a continuous-flow reactor was used to react ethanol with lactic acid prepared from an ammonium lactate concentrate produced in fermentations conducted at the EERC. Good yields of ester were obtained even though the concentration of lactic acid in the feed was low with respect to the amount of water present. Esterification gave lower yields of ester, owing to the lowered lactic acid content of the feed. All lactic acid fermentation from amylose hydrolysate test trials was completed. Management activities included a decision to extend several projects to December 31, 2003, because of delays in receiving biomass feedstocks for testing and acquisition of commercial matching funds. In strategic studies, methods for producing acetate esters for high-value fibers, fuel additives, solvents, and chemical intermediates were discussed with several commercial entities. Commercial industries have an interest in efficient biomass gasification designs but are waiting for economic incentives. Utility, biorefinery, pulp and paper, or other industries are interested in lignin as a potential fuel or feedstock but need more information on properties.« less

Distribution of trace elements in selected pulverized coals as a function of particle size and density

USGS Publications Warehouse

Senior, C.L.; Zeng, T.; Che, J.; Ames, M.R.; Sarofim, A.F.; Olmez, I.; Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Mroczkowski, S.; Palmer, C.; Finkelman, R.

2000-01-01

Trace elements in coal have diverse modes of occurrence that will greatly influence their behavior in many coal utilization processes. Mode of occurrence is important in determining the partitioning during coal cleaning by conventional processes, the susceptibility to oxidation upon exposure to air, as well as the changes in physical properties upon heating. In this study, three complementary methods were used to determine the concentrations and chemical states of trace elements in pulverized samples of four US coals: Pittsburgh, Illinois No. 6, Elkhorn and Hazard, and Wyodak coals. Neutron Activation Analysis (NAA) was used to measure the absolute concentration of elements in the parent coals and in the size- and density-fractionated samples. Chemical leaching and X-ray absorption fine structure (XAFS) spectroscopy were used to provide information on the form of occurrence of an element in the parent coals. The composition differences between size-segregated coal samples of different density mainly reflect the large density difference between minerals, especially pyrite, and the organic portion of the coal. The heavy density fractions are therefore enriched in pyrite and the elements associated with pyrite, as also shown by the leaching and XAFS methods. Nearly all the As is associated with pyrite in the three bituminous coals studied. The sub-bituminous coal has a very low content of pyrite and arsenic; in this coal arsenic appears to be primarily organically associated. Selenium is mainly associated with pyrite in the bituminous coal samples. In two bituminous coal samples, zinc is mostly in the form of ZnS or associated with pyrite, whereas it appears to be associated with other minerals in the other two coals. Zinc is also the only trace element studied that is significantly more concentrated in the smaller (45 to 63 ??m) coal particles.

Distribution of potentially hazardous trace elements in coals from Shanxi province, China

USGS Publications Warehouse

Zhang, J.Y.; Zheng, C.G.; Ren, D.Y.; Chou, C.-L.; Liu, J.; Zeng, R.-S.; Wang, Z.P.; Zhao, F.H.; Ge, Y.T.

2004-01-01

Shanxi province, located in the center of China, is the biggest coal base of China. There are five coal-forming periods in Shanxi province: Late Carboniferous (Taiyuan Formation), Early Permian (Shanxi Formation), Middle Jurassic (Datong Formation), Tertiary (Taxigou Formation), and Quaternary. Hundred and ten coal samples and a peat sample from Shanxi province were collected and the contents of 20 potentially hazardous trace elements (PHTEs) (As, B, Ba, Cd, Cl, Co, Cr, Cu, F, Hg, Mn, Mo, Ni, Pb, Sb, Se, Th, U, V and Zn) in these samples were determined by instrumental neutron activation analysis, atomic absorption spectrometry, cold-vapor atomic absorption spectrometry, ion chromatography spectrometry, and wet chemical analysis. The result shows that the brown coals are enriched in As, Ba, Cd, Cr, Cu, F and Zn compared with the bituminous coals and anthracite, whereas the bituminous coals are enriched in B, Cl, Hg, and the anthracite is enriched in Cl, Hg, U and V. A comparison with world averages and crustal abundances (Clarke values) shows that the Quaternary peat is highly enriched in As and Mo, Tertiary brown coals are highly enriched in Cd, Middle Jurassic coals, Early Permian coals and Late Carboniferous coals are enriched in Hg. According to the coal ranks, the bituminous coals are highly enriched in Hg, whereas Cd, F and Th show low enrichments, and the anthracite is also highly enriched in Hg and low enrichment in Th. The concentrations of Cd, F, Hg and Th in Shanxi coals are more than world arithmetic means of concentrations for the corresponding elements. Comparing with the United States coals, Shanxi coals show higher concentrations of Cd, Hg, Pb, Se and Th. Most of Shanxi coals contain lower concentrations of PHTEs. ?? 2004 Elsevier Ltd. All rights reserved.

An investigation of the role of water on retrograde/condensation reactions and enhanced liquefaction yields. Quarterly progress report, January 1, 1994--March 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miknis, F.P.; Netzel, D.A.

The results of coal swelling measurements using 1,4-dioxane as the swelling reagent for premoisturized coals (raw) and coal dried thermally, chemically, and with microwave radiation are presented. An increase in the swelling ratio relative to raw coal indicates a decrease in the amount of cross-linking in the coal. Conversely, a decrease in the ratio indicates an increase in cross-linking. The extent of cross-linking (as measured by 1,4-dioxane) for Texas, Black Thunder, and Eagle Butte Coals are about the same. Illinois {number_sign}6 coal appears to have less cross-linking relative to the other three coals. These results are expected on the basismore » of coal rank. The increase in cross linking is most pronounced for coals dried thermally and with microwave radiation. A decrease in the swelling ratios for all four coals suggests that cross-linking had occurred possibly due to partial devolatilization process. However, low temperature, chemical dehydration of the coals causes only a small or no change in the internal structure for Texas and Illinois {number_sign}6 coals whereas a significant decrease in the cross-linking structure for the Black Thunder and Eagle Butte coals is observed. It is possible that the solvent (CH{sub 3}OH) and products resulting from the chemical dehydrating (acetone and methanol) occupy the surface sites that water had before the reaction and thus preventing cross-linking to occur. These reagents can also promote swelling of coals and may account for some of the decrease in the cross-linking of the coal structure observed for the chemically dried coals.« less

Tertiary coals in South Texas: Anomalous cannel-like coals of Webb County (Claiborne Group, Eocene) and lignites of Atascosa County (Jackson Group, Eocene) - Geologic setting, character, source-rock and coal-bed methane potential

USGS Publications Warehouse

Warwick, Peter D.; Aubourg, Claire E.; Willett, Jason C.

1999-01-01

The coal-bearing Gulf of Mexico Coastal Plain of North America contains a variety of depositional settings and coal types. The coal-bearing region extends westward from Alabama and Mississippi, across Louisiana to the northern part of the Mississippi Embayment, and then southward to eastern Arkansas, Texas and northern Mexico (fig. 1). Most of the coal currently mined in Texas is lignite from the upper part of the Wilcox Group (Paleocene-Eocene) and, in Louisiana, lignite is mined from the lower part of the Wilcox (fig. 2). Gulf Coast coal is used primarily as fuel for mine-mouth electric plants. On this field trip we will visit the only two non-Wilcox coal mining intervals in the Texas-Louisiana Coastal Plain; these include the San Pedro - Santo Tomas bituminous cannel-like coal zone of the Eocene Claiborne Group, and the San Miguel lignite coal zone of the Eocene Jackson Group (fig. 2). Other coal-mining areas in northern Mexico are currently producing bituminous coal from the Cretaceous Olmos Formation of the Navaro Group (fig. 2).

Fungal biodegradation of hard coal by a newly reported isolate, Neosartorya fischeri.

PubMed

Igbinigie, Eric E; Aktins, Simon; van Breugel, Yvonne; van Dyke, Susan; Davies-Coleman, Michael T; Rose, Peter D

2008-11-01

Cynodon dactylon (Bermuda grass) has been observed to grow sporadically on the surface of coal dumps in the Witbank coal mining area of South Africa. Root zone investigation indicated that a number of fungal species may be actively involved in the biodegradation of hard coal, thus enabling the survival of the plant, through mutualistic interaction, in this extreme environment. In an extensive screening program of over two thousand samples, the Deuteromycete, Neosartorya fischeri, was isolated and identified. The biodegradation of coal by N. fischeri was tested in flask studies and in a perfusion fixed-bed bioreactor used to simulate the coal dump environment. The performance of N. fischeri was compared to Phanaerochaete chrysosporium and Trametes (Polyporus) versicolor, previously described in coal biodegradation studies. Fourier transform infrared spectrometry and pyrolysis gas chromatography mass spectrometry of the biodegradation product indicated oxidation of the coal surface and nitration of the condensed aromatic structures of the coal macromolecule as possible reaction mechanisms in N. fischeri coal biodegradation. This is a first report of N. fischeri-mediated coal biodegradation and, in addition to possible applications in coal biotechnology, the findings may enable development of sustainable technologies in coal mine rehabilitation.

Chemical analyses of coal, coal-associated rocks and coal combustion products collected for the National Coal Quality Inventory

USGS Publications Warehouse

Hatch, Joseph R.; Bullock, John H.; Finkelman, Robert B.

2006-01-01

In 1999, the USGS initiated the National Coal Quality Inventory (NaCQI) project to address a need for quality information on coals that will be mined during the next 20-30 years. At the time this project was initiated, the publicly available USGS coal quality data was based on samples primarily collected and analyzed between 1973 and 1985. The primary objective of NaCQI was to create a database containing comprehensive, accurate and accessible chemical information on the quality of mined and prepared United States coals and their combustion byproducts. This objective was to be accomplished through maintaining the existing publicly available coal quality database, expanding the database through the acquisition of new samples from priority areas, and analysis of the samples using updated coal analytical chemistry procedures. Priorities for sampling include those areas where future sources of compliance coal are federally owned. This project was a cooperative effort between the U.S. Geological Survey (USGS), State geological surveys, universities, coal burning utilities, and the coal mining industry. Funding support came from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE).

Nitrogen in Chinese coals

USGS Publications Warehouse

Wu, D.; Lei, J.; Zheng, B.; Tang, X.; Wang, M.; Hu, Jiawen; Li, S.; Wang, B.; Finkelman, R.B.

2011-01-01

Three hundred and six coal samples were taken from main coal mines of twenty-six provinces, autonomous regions, and municipalities in China, according to the resource distribution and coal-forming periods as well as the coal ranks and coal yields. Nitrogen was determined by using the Kjeldahl method at U. S. Geological Survey (USGS), which exhibit a normal frequency distribution. The nitrogen contents of over 90% Chinese coal vary from 0.52% to 1.41% and the average nitrogen content is recommended to be 0.98%. Nitrogen in coal exists primarily in organic form. There is a slight positive relationship between nitrogen content and coal ranking. ?? 2011 Science Press, Institute of Geochemistry, CAS and Springer Berlin Heidelberg.

Ferromagnetic and superparamagnetic contamination in pulverized coal

USGS Publications Warehouse

Senftle, F.E.; Thorpe, A.N.; Alexander, C.C.; Finkelman, R.B.

1982-01-01

Although no significant major-element contamination is introduced by grinding coal in a steel pulverizer, abraded steel particles can conceivably affect the magnetic properties of pulverized coal. Magnetic and scanning-electron-microscope analyses of pulverized coal and coal fragments from the Herrin No. 6 seam in Illinois showed ferromagnetic and superparamagnetic contamination from the grinder. Significant changes in the magnetic properties of the coal were noted, indicating a total steel contamination of approximately 0.02 wt%. When coal samples were vibrated in the magnetic field of the vibrating-sample magnetometer, the superparamagnetic steel particles moved through the pulverized coal, and participated in the formation of multidomain clusters that in turn substantially affected the magnetization of the coal. ?? 1982.

Self-Scrubbing Coal -- an integrated approach to clean air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrison, K.E.

1997-12-31

Carefree Coal is coal cleaned in a proprietary dense-media cyclone circuit, using ultrafine magnetite slurries, to remove noncombustible material, including up to 90% of the pyritic sulfur. Deep cleaning alone, however, cannot produce a compliance fuel from coals with high organic sulfur contents. In these cases, Self-Scrubbing Coal will be produced. Self-Scrubbing Coal is produced in the same manner as Carefree Coal except that the finest fraction of product from the cleaning circuit is mixed with limestone-based additives and briquetted. The reduced ash content of the deeply-cleaned coal will permit the addition of relatively large amounts of sorbent without exceedingmore » boiler ash specifications or overloading electrostatic precipitators. This additive reacts with sulfur dioxide (SO{sub 2}) during combustion of the coal to remove most of the remaining sulfur. Overall, sulfur reductions in the range of 80--90% are achieved. After nearly 5 years of research and development of a proprietary coal cleaning technology coupled with pilot-scale validation studies of this technology and pilot-scale combustion testing of Self-Scrubbing Coal, Custom Coals Corporation organized a team of experts to prepare a proposal in response to DOE`s Round IV Program Opportunity Notice for its Clean Coal Technology Program under Public Law 101-121 and Public Law 101-512. The main objective of the demonstration project is the production of a coal fuel that will result in up to 90% reduction in sulfur emissions from coal-fired boilers at a cost competitive advantage over other technologies designed to accomplish the same sulfur emissions and over naturally occurring low sulfur coals.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nabeel, A.; Khan, T.A.; Sharma, D.K.

The use of low-grade coal in thermal power stations is leading to environmental pollution due to the generation of large amounts of fly ash, bottom ash, and CO{sub 2} besides other pollutants. It is therefore important to clean the coal before using it in thermal power stations, steel plants, or cement industries etc. Physical beneficiation of coal results in only limited cleaning of coal. The increasing environmental pollution problems from the use of coal have led to the development of clean coal technologies. In fact, the clean use of coal requires the cleaning of coal to ultra low ash contents,more » keeping environmental norms and problems in view and the ever-growing need to increase the efficiency of coal-based power generation. Therefore this requires the adaptation of chemical cleaning techniques for cleaning the coal to obtain ultra clean coal having ultra low ash contents. Presently the reaction conditions for chemical demineralization of low-grade coal using 20% aq NaOH treatment followed by 10% H{sub 2}SO{sub 4} leaching under reflux conditions have been optimized. In order to reduce the concentration of alkali and acid used in this process of chemical demineralization of low-grade coals, stepwise, i.e., three step process of chemical demineralization of coal using 1% or 5% aq NaOH treatment followed by 1% or 5% H{sub 2}SO{sub 4} leaching has been developed, which has shown good results in demineralization of low-grade coals. In order to conserve energy, the alkali-acid leaching of coal was also carried out at room temperature, which gave good results.« less

Regulation of coal polymer degradation by fungi. Tenth Quartery report, October 1996--December 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Irvine, R.L.; Bumpus, J.A.

1997-01-28

It has long been known that low rank coal such as leonardite can be solubilized by strong base (>pH 12). Recent discoveries have also shown that leonardite is solubilized by Lewis bases at considerably lower pH values and by fungi that secrete certain Lewis bases (i.e., oxalate ion). During the current reporting period we have studied the ability of a strong base (sodium hydroxide, pH 12), and two fungi, Phanerochaete chrysosporium and Trametes versicolor, to solubilize Argonne Premium Coals. In general, Argonne Premium Coals were relatively resistant to base mediated solubilization. However, when these coals were preoxidized (150{degrees}C for sevenmore » days), substantial amounts of several coals were solubilized. Most affected were the Lewiston-Stockton bituminous coal, the Beulah-Zap lignite, the Wyodak-Anderson subbituminous coal and the Blind Canyon bituminous coal. Argonne Premium Coals were previously shown by us to be relatively resistant to solubilization by sodium oxalate. When preoxidized coals were treated with sodium oxalate, only the Beulah-Zap lignite was substantially solubilized. Although very small amounts of the other preoxidized coals were solubilized by treatment with oxalate, the small amount of solubilization that did take place was generally increased relative to that observed for coals that were not preoxidized. None of the Argonne Premium Coals were solubilized by P. chrysosporium or T. versicolor. Of considerable interest, however, is the observation that P. chrysosporium and T. versicolor mediated extensive solubilization of Lewiston-Stockton bituminous coal, the Beulah-Zap lignite and the Wyodak-Anderson subbituminous coal.« less

The U.S. Energy Dilemma: The Gap between Today’s Requirements and Tomorrow’s Potential.

DTIC Science & Technology

1973-07-01

Possible Solutions . ........ .. 142 Use of Low-Sulfur Coal ................ 43 Flue - Gas Desulfurization ................ 43 Coal Cleaning...1) use of low-sulfur coal, (2) flue - gas desulfurization , (3) coal cleaning, (4) coal refining, and (5) coal conversion. Use of Low-Sulfur Coal The...to the same point (Skillings Mining Rev., 1973). Flue - Gas Desulfurization With standards based on sulfur dioxide emissions per million Btu, rather than

30 CFR 1206.464 - Value enhancement of marketable coal.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Value enhancement of marketable coal. 1206.464... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.464 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been...

30 CFR 1206.459 - Allocation of washed coal.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Allocation of washed coal. 1206.459 Section... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When...

30 CFR 1206.464 - Value enhancement of marketable coal.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Value enhancement of marketable coal. 1206.464... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.464 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been...

78 FR 50447 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Cleanup...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-19

... for OMB Review; Comment Request; Cleanup Program for Accumulations of Coal and Float Coal Dusts, Loose Coal, and Other Combustibles ACTION: Notice. SUMMARY: The Department of Labor (DOL) is submitting the... (ICR) proposal; titled, ``Cleanup Program for Accumulations of Coal and Float Coal Dusts, Loose Coal...

30 CFR 75.1709 - Accumulations of methane and coal dust on surface coal-handling facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Accumulations of methane and coal dust on surface coal-handling facilities. 75.1709 Section 75.1709 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES...

30 CFR 206.464 - Value enhancement of marketable coal.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Value enhancement of marketable coal. 206.464... MANAGEMENT PRODUCT VALUATION Indian Coal § 206.464 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been placed in...

30 CFR 1206.459 - Allocation of washed coal.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Allocation of washed coal. 1206.459 Section... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When...

30 CFR 1206.253 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Coal subject to royalties-general provisions... INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.253 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM under 43 CFR part 3400...

30 CFR 206.265 - Value enhancement of marketable coal.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Value enhancement of marketable coal. 206.265... MANAGEMENT PRODUCT VALUATION Federal Coal § 206.265 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been placed in...

30 CFR 1206.260 - Allocation of washed coal.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Allocation of washed coal. 1206.260 Section... INTERIOR Natural Resources Revenue PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was...

Desulfurizing Coal By Chlorinolysis and Hydrogenation

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Rohatgi, N. K.

1983-01-01

85 percent of organic and pyritic sulfur in coal removed by combination of chlorinolysis and hydrogeneration. Coal is fed to hydrogenator after chlorination. Coal flows against hydrogen current increasing mixing and reducing hydrogen consumption. Excess hydrogen is recovered from gaseous reaction products. Product coal contained 62.5 percent less total sulfur than same coal after chlorination.

30 CFR 75.1709 - Accumulations of methane and coal dust on surface coal-handling facilities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Accumulations of methane and coal dust on surface coal-handling facilities. 75.1709 Section 75.1709 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES...

30 CFR 1206.260 - Allocation of washed coal.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Allocation of washed coal. 1206.260 Section... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When...

30 CFR 206.452 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Coal subject to royalties-general provisions... MINERALS REVENUE MANAGEMENT PRODUCT VALUATION Indian Coal § 206.452 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM pursuant to 43 CFR group 3400...

30 CFR 206.253 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Coal subject to royalties-general provisions... MINERALS REVENUE MANAGEMENT PRODUCT VALUATION Federal Coal § 206.253 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM under 43 CFR part 3400) from a...

30 CFR 1206.253 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Coal subject to royalties-general provisions... INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.253 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM under 43 CFR part 3400...

30 CFR 1206.265 - Value enhancement of marketable coal.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Value enhancement of marketable coal. 1206.265... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.265 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been...

30 CFR 75.1709 - Accumulations of methane and coal dust on surface coal-handling facilities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Accumulations of methane and coal dust on surface coal-handling facilities. 75.1709 Section 75.1709 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES...

30 CFR 1206.459 - Allocation of washed coal.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Allocation of washed coal. 1206.459 Section... INTERIOR Natural Resources Revenue PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was...

30 CFR 1206.265 - Value enhancement of marketable coal.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Value enhancement of marketable coal. 1206.265... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.265 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been...

30 CFR 1206.265 - Value enhancement of marketable coal.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Value enhancement of marketable coal. 1206.265... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.265 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been...

30 CFR 75.1709 - Accumulations of methane and coal dust on surface coal-handling facilities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Accumulations of methane and coal dust on surface coal-handling facilities. 75.1709 Section 75.1709 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES...

30 CFR 1206.452 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Coal subject to royalties-general provisions..., DEPARTMENT OF THE INTERIOR Natural Resources Revenue PRODUCT VALUATION Indian Coal § 1206.452 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM pursuant to 43...

30 CFR 1206.260 - Allocation of washed coal.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Allocation of washed coal. 1206.260 Section... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When...

30 CFR 1206.253 - Coal subject to royalties-general provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Coal subject to royalties-general provisions... INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.253 Coal subject to royalties—general provisions. (a) All coal (except coal unavoidably lost as determined by BLM under 43 CFR part 3400...

Attitudes toward Women Coal Miners in an Appalachian Coal Community.

ERIC Educational Resources Information Center

Trent, Roger B.; Stout-Wiegand, Nancy

1987-01-01

In a coal mining community, a survey revealed that the level of negative sentiment toward women coal miners was substantial and varied by gender role. Male coal miners were negative toward female co-workers, but they supported women's right to coal mine jobs, while female homemakers did not. (Author/CH)

30 CFR 1206.464 - Value enhancement of marketable coal.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Value enhancement of marketable coal. 1206.464... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.464 Value enhancement of marketable coal. If, prior to use, sale, or other disposition, the lessee enhances the value of coal after the coal has been...

30 CFR 1206.459 - Allocation of washed coal.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Allocation of washed coal. 1206.459 Section... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When...

30 CFR 1206.260 - Allocation of washed coal.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Allocation of washed coal. 1206.260 Section... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When...

Simulated coal spill causes mortality and growth inhibition in tropical marine organisms

PubMed Central

Berry, Kathryn L. E.; Hoogenboom, Mia O.; Flores, Florita; Negri, Andrew P.

2016-01-01

Coal is a principal fossil fuel driving economic and social development, and increases in global coal shipments have paralleled expansion of the industry. To identify the potential harm associated with chronic marine coal contamination, three taxa abundant in tropical marine ecosystems (the coral Acropora tenuis, the reef fish Acanthochromis polyacanthus and the seagrass Halodule uninervis) were exposed to five concentrations (0–275 mg coal l−1) of suspended coal dust (<63 μm) over 28 d. Results demonstrate that chronic coal exposure can cause considerable lethal effects on corals, and reductions in seagrass and fish growth rates. Coral survivorship and seagrass growth rates were inversely related to increasing coal concentrations (≥38 mg coal l−1) and effects increased between 14 and 28 d, whereas fish growth rates were similarly depressed at all coal concentrations tested. This investigation provides novel insights into direct coal impacts on key tropical taxa for application in the assessment of risks posed by increasing coal shipments in globally threatened marine ecosystems. PMID:27174014

An Organic Geochemical Assessment of CO2-Coal Interactions During Sequestration

USGS Publications Warehouse

Kolak, Jonathan J.; Burruss, Robert A.

2003-01-01

Three well-characterized coal samples of varying rank were extracted with supercritical CO2 to determine the amount of polycyclic aromatic hydrocarbons (PAHs) that could be mobilized during simulated CO2 injection/sequestration in deep coal beds. The supercritical CO2 extractions were conducted at 40?C and 100 bars, roughly corresponding to a depth of 1 km. The greatest amount of PAHs was extracted from the high-volatile C bituminous coal sample. Extracts from the subbituminous C and anthracite coal samples contained lower concentrations of these compounds. The effectiveness of supercritical CO2 in liberating PAHs from the coal sample was evaluated in a comparison with a parallel series of Soxhlet extractions using 100% dichloromethane. More PAHs were extracted from the lower rank coal samples with dichloromethane than with supercritical CO2. The results from this investigation indicate that, regardless of coal rank, CO2 injection into deep coal beds may mobilize PAHs from the coal matrix. However, more PAHs could be mobilized during CO2 sequestration in a high-volatile C bituminous coal bed than in either of the other two coal ranks studied.

National Coal Quality Inventory (NACQI)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert Finkelman

2005-09-30

The U.S. Geological Survey (USGS) conducted the National Coal Quality Inventory (NaCQI) between 1999 and 2005 to address a need for quality information on coals that will be mined during the next 20-30 years. Collaboration between the USGS, State geological surveys, universities, coal burning utilities, and the coal mining industry plus funding support from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE) permitted collection and submittal of coal samples for analysis. The chemical data (proximate and ultimate analyses; major, minor and trace element concentrations) for 729 samples of raw or prepared coal, coal associated shale,more » and coal combustion products (fly ash, hopper ash, bottom ash and gypsum) from nine coal producing States are included. In addition, the project identified a new coal reference analytical standard, to be designated CWE-1 (West Elk Mine, Gunnison County, Colorado) that is a high-volatile-B or high-volatile-A bituminous coal with low contents of ash yield and sulfur, and very low, but detectable contents of chlorine, mercury and other trace elements.« less

A study of coal production in Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akarakiri, J.B.; Afonja, A.A.; Okejiri, E.C.

The Nigerian coal industry was studied. The focus was on the problems which have caused low production output of coal. More specifically, the study examined the present techniques of coal production, the causes of low production of coal, the coal production policy as it affected this study, and proposed policy measures to address the findings. It was discovered that some of the limiting factors to coal production in Nigeria could be attributed to the lack of the following: (i) clear and specific production-demand targets set for coal in Nigeria; (ii) adequate technological capability to mechanize coal mining operations in Nigeria;more » (iii) venture capital to invest in coal production; (iv) poor infrastructural facilities for coal production such as mining, storage, transportation, etc. It was also discovered that the dissatisfaction of the miners with their conditions of service influenced production capacity negatively. These findings point to the reality that coal is unlikely to play a major role in the country's energy equation in the near future unless serious efforts are made to address the above issues.« less

Coal: Its Structure and Some of Its Uses.

ERIC Educational Resources Information Center

Phillips, P. S.

1981-01-01

Describes the formation, chemical structure, and several uses of coal. The history of coal usage, production processes, coal tar products, and production of petroleum and other hydrocarbons from coal are also described. (DS)

Cooling Effect Analysis of Suppressing Coal Spontaneous Ignition with Heat Pipe

NASA Astrophysics Data System (ADS)

Zhang, Yaping; Zhang, Shuanwei; Wang, Jianguo; Hao, Gaihong

2018-05-01

Suppression of spontaneous ignition of coal stockpiles was an important issue for safe utilization of coal. The large thermal energy from coal spontaneous ignition can be viewed as the latent energy source to further utilize for saving energy purpose. Heat pipe was the more promising way to diffuse effectively concentrated energy of the coal stockpile, so that retarding coal spontaneous combustion was therefore highly desirable. The cooling mechanism of the coal with heat pipe was pursued. Based on the research result, the thermal energy can be transported from the coal seam to the surface continuously with the use of heat pipe. Once installed the heat pipes will work automatically as long as the coal oxidation reaction was happened. The experiment was indicated that it can significantly spread the high temperature of the coal pile.