Force Transmission Modes of Non-Cohesive and Cohesive Materials at the Critical State

PubMed Central

2017-01-01

This paper investigates the force transmission modes, mainly described by probability density distributions, in non-cohesive dry and cohesive wet granular materials by discrete element modeling. The critical state force transmission patterns are focused on with the contact model effect being analyzed. By shearing relatively dense and loose dry specimens to the critical state in the conventional triaxial loading path, it is observed that there is a unique critical state force transmission mode. There is a universe critical state force distribution pattern for both the normal contact forces and tangential contact forces. Furthermore, it is found that using either the linear Hooke or the non-linear Hertz model does not affect the universe force transmission mode, and it is only related to the grain size distribution. Wet granular materials are also simulated by incorporating a water bridge model. Dense and loose wet granular materials are tested, and the critical state behavior for the wet material is also observed. The critical state strength and void ratio of wet granular materials are higher than those of a non-cohesive material. The critical state inter-particle distribution is altered from that of a non-cohesive material with higher probability in relatively weak forces. Grains in non-cohesive materials are under compressive stresses, and their principal directions are mainly in the axial loading direction. However, for cohesive wet granular materials, some particles are in tension, and the tensile stresses are in the horizontal direction on which the confinement is applied. The additional confinement by the tensile stress explains the macro strength and dilatancy increase in wet samples. PMID:28858238

Disaggregation of small, cohesive rubble pile asteroids due to YORP

NASA Astrophysics Data System (ADS)

Scheeres, D. J.

2018-04-01

The implication of small amounts of cohesion within relatively small rubble pile asteroids is investigated with regard to their evolution under the persistent presence of the YORP effect. We find that below a characteristic size, which is a function of cohesive strength, density and other properties, rubble pile asteroids can enter a "disaggregation phase" in which they are subject to repeated fissions after which the formation of a stabilizing binary system is not possible. Once this threshold is passed rubble pile asteroids may be disaggregated into their constituent components within a finite time span. These constituent components will have their own spin limits - albeit potentially at a much higher spin rate due to the greater strength of a monolithic body. The implications of this prediction are discussed and include modification of size distributions, prevalence of monolithic bodies among meteoroids and the lifetime of small rubble pile bodies in the solar system. The theory is then used to place constraints on the strength of binary asteroids characterized as a function of their type.

Cohesive detachment of an elastic pillar from a dissimilar substrate

NASA Astrophysics Data System (ADS)

Fleck, N. A.; Khaderi, S. N.; McMeeking, R. M.; Arzt, E.

The adhesion of micron-scale surfaces due to intermolecular interactions is a subject of intense interest spanning electronics, biomechanics and the application of soft materials to engineering devices. The degree of adhesion is sensitive to the diameter of micro-pillars in addition to the degree of elastic mismatch between pillar and substrate. Adhesion-strength-controlled detachment of an elastic circular cylinder from a dissimilar substrate is predicted using a Dugdale-type of analysis, with a cohesive zone of uniform tensile strength emanating from the interface corner. Detachment initiates when the opening of the cohesive zone attains a critical value, giving way to crack formation. When the cohesive zone size at crack initiation is small compared to the pillar diameter, the initiation of detachment can be expressed in terms of a critical value Hc of the corner stress intensity. The estimated pull-off force is somewhat sensitive to the choice of stick/slip boundary condition used on the cohesive zone, especially when the substrate material is much stiffer than the pillar material. The analysis can be used to predict the sensitivity of detachment force to the size of pillar and to the degree of elastic mismatch between pillar and substrate.

Slope stability analysis using limit equilibrium method in nonlinear criterion.

PubMed

Lin, Hang; Zhong, Wenwen; Xiong, Wei; Tang, Wenyu

2014-01-01

In slope stability analysis, the limit equilibrium method is usually used to calculate the safety factor of slope based on Mohr-Coulomb criterion. However, Mohr-Coulomb criterion is restricted to the description of rock mass. To overcome its shortcomings, this paper combined Hoek-Brown criterion and limit equilibrium method and proposed an equation for calculating the safety factor of slope with limit equilibrium method in Hoek-Brown criterion through equivalent cohesive strength and the friction angle. Moreover, this paper investigates the impact of Hoek-Brown parameters on the safety factor of slope, which reveals that there is linear relation between equivalent cohesive strength and weakening factor D. However, there are nonlinear relations between equivalent cohesive strength and Geological Strength Index (GSI), the uniaxial compressive strength of intact rock σ ci , and the parameter of intact rock m i . There is nonlinear relation between the friction angle and all Hoek-Brown parameters. With the increase of D, the safety factor of slope F decreases linearly; with the increase of GSI, F increases nonlinearly; when σ ci is relatively small, the relation between F and σ ci is nonlinear, but when σ ci is relatively large, the relation is linear; with the increase of m i , F decreases first and then increases.

Slope Stability Analysis Using Limit Equilibrium Method in Nonlinear Criterion

PubMed Central

Lin, Hang; Zhong, Wenwen; Xiong, Wei; Tang, Wenyu

2014-01-01

In slope stability analysis, the limit equilibrium method is usually used to calculate the safety factor of slope based on Mohr-Coulomb criterion. However, Mohr-Coulomb criterion is restricted to the description of rock mass. To overcome its shortcomings, this paper combined Hoek-Brown criterion and limit equilibrium method and proposed an equation for calculating the safety factor of slope with limit equilibrium method in Hoek-Brown criterion through equivalent cohesive strength and the friction angle. Moreover, this paper investigates the impact of Hoek-Brown parameters on the safety factor of slope, which reveals that there is linear relation between equivalent cohesive strength and weakening factor D. However, there are nonlinear relations between equivalent cohesive strength and Geological Strength Index (GSI), the uniaxial compressive strength of intact rock σ ci, and the parameter of intact rock m i. There is nonlinear relation between the friction angle and all Hoek-Brown parameters. With the increase of D, the safety factor of slope F decreases linearly; with the increase of GSI, F increases nonlinearly; when σ ci is relatively small, the relation between F and σ ci is nonlinear, but when σ ci is relatively large, the relation is linear; with the increase of m i, F decreases first and then increases. PMID:25147838

Modelling increased soil cohesion by plant roots with EUROSEM

NASA Astrophysics Data System (ADS)

de Baets, S.; Poesen, J.; Torri, D.; Salvador, M. P.

2009-04-01

Soil cohesion is an important variable to model soil detachment by runoff (Morgan et al., 1998a). As soil particles are not loose, soil detachment by runoff will be limited by the cohesion of the soil material. It is generally recognized that plant roots contribute to the overall cohesion of the soil. Determination of this increased cohesion and soil roughness however is complicated and measurements of shear strength and soil reinforcement by plant roots are very time- and labour consuming. A model approach offers an alternative for the assessment of soil cohesion provided by plant roots However, few erosion models account for the effects of the below-ground biomass in their calculation of erosion rates. Therefore, the main objectives of this study is to develop an approach to improve an existing soil erosion model (EUROSEM) accounting for the erosion-reducing effects of roots. The approach for incorporating the root effects into this model is based on a comparison of measured soil detachment rates for bare and for root-permeated topsoil samples with predicted erosion rates under the same flow conditions using the erosion equation of EUROSEM. Through backwards calculation, transport capacity efficiencies and corresponding soil cohesion values can be assessed for bare and root-permeated topsoils respectively. The results are promising and show that grass roots provide a larger increase in soil cohesion as compared with tap-rooted species and that the increase in soil cohesion is not significantly different under wet and dry soil conditions, either for fibrous root systems or for tap root systems. Relationships are established between measured root density values and the corresponding calculated soil cohesion values, reflecting the effects of roots on the resistance of the topsoil to concentrated flow incision. These relationships enable one to incorporate the root effect into the soil erosion model EUROSEM, through adapting the soil cohesion input value. A scenario analysis performed with EUROSEM for different vegetation treatments, indicates that runoff and soil loss on root-permeated topsoils are slightly higher as compared to fully covered grass fields or harvested grass fields with some plant residue left, but much smaller as compared to bare topsoils. Moreover, when re-vegetating bare soils, roots are responsible for a large part of the reduction in soil loss and runoff by concentrated flow. Hence, this analysis shows that the contribution of roots to soil cohesion is very important for preventing soil loss and reducing runoff volume. The increase in soil shear strength due to the binding effect of roots on soil particles is two orders of magnitude lower as compared with soil reinforcement achieved when roots mobilize their tensile strength during soil shearing and root breakage.

Application of continuous normal-lognormal bivariate density functions in a sensitivity analysis of municipal solid waste landfill.

PubMed

Petrovic, Igor; Hip, Ivan; Fredlund, Murray D

2016-09-01

The variability of untreated municipal solid waste (MSW) shear strength parameters, namely cohesion and shear friction angle, with respect to waste stability problems, is of primary concern due to the strong heterogeneity of MSW. A large number of municipal solid waste (MSW) shear strength parameters (friction angle and cohesion) were collected from published literature and analyzed. The basic statistical analysis has shown that the central tendency of both shear strength parameters fits reasonably well within the ranges of recommended values proposed by different authors. In addition, it was established that the correlation between shear friction angle and cohesion is not strong but it still remained significant. Through use of a distribution fitting method it was found that the shear friction angle could be adjusted to a normal probability density function while cohesion follows the log-normal density function. The continuous normal-lognormal bivariate density function was therefore selected as an adequate model to ascertain rational boundary values ("confidence interval") for MSW shear strength parameters. It was concluded that a curve with a 70% confidence level generates a "confidence interval" within the reasonable limits. With respect to the decomposition stage of the waste material, three different ranges of appropriate shear strength parameters were indicated. Defined parameters were then used as input parameters for an Alternative Point Estimated Method (APEM) stability analysis on a real case scenario of the Jakusevec landfill. The Jakusevec landfill is the disposal site of the capital of Croatia - Zagreb. The analysis shows that in the case of a dry landfill the most significant factor influencing the safety factor was the shear friction angle of old, decomposed waste material, while in the case of a landfill with significant leachate level the most significant factor influencing the safety factor was the cohesion of old, decomposed waste material. The analysis also showed that a satisfactory level of performance with a small probability of failure was produced for the standard practice design of waste landfills as well as an analysis scenario immediately after the landfill closure. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of transition metal impurities on the strength of grain boundaries in vanadium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Xuebang; Kong, Xiang-Shan; You, Yu-Wei

2016-09-07

Effects of 3d (Ti-Ni), 4d (Zr-Pd), and 5d (Hf-Pt) transition metal impurities on strength of two representative vanadium grain boundaries (GBs), symmetric Σ3(111) and asymmetric Σ5(210), were studied by first-principles calculations within the framework of the Rice-Wang thermodynamic model and within the computational tensile test. The desirable elements to increase the GB cohesion were predicted based on their segregation and strengthening behaviors across the different GB sites. It reveals that the elements Ti, Zr, Hf, Nb, and Ta are good choices for the GB cohesion enhancers. In addition, the GB strengthening by solutes is sensitive to the GB structures. Themore » elements Cr, Mn, Fe, Co, and Ni decrease the GB strength of the Σ3(111) GB but they can increase the cohesion of the Σ5(210) GB. Furthermore, the origin of Ti-induced change of the GB strength was uncovered by analyzing the atomic bonds and electronic structures as well as the tensile strength. This work provides a theoretical guidance to screen promising alloying elements in V-based materials with improved resistance to GB decohesion and also helps us to understand the formation mechanism of Ti-rich precipitates in the V-Cr-Ti alloys under neutron or ion irradiation environments.« less

Adhesive and Cohesive Strength in FeB/Fe2B Systems

NASA Astrophysics Data System (ADS)

Meneses-Amador, A.; Blancas-Pérez, D.; Corpus-Mejía, R.; Rodríguez-Castro, G. A.; Martínez-Trinidad, J.; Jiménez-Tinoco, L. F.

2018-05-01

In this work, FeB/Fe2B systems were evaluated by the scratch test. The powder-pack boriding process was performed on the surface of AISI M2 steel. The mechanical parameters, such as yield stress and Young's modulus of the boride layer, were obtained by the instrumented indentation technique. Residual stresses produced on the boride layer were estimated by using the x-ray diffraction (XRD) technique. The scratch test was performed in order to evaluate the cohesive/adhesive strength of the FeB/Fe2B coating. In addition, a numerical evaluation of the scratch test on boride layers was performed by the finite element method. Maximum principal stresses were related to the failure mechanisms observed by the experimental scratch test. Shear stresses at the interfaces of the FeB/Fe2B/substrate system were also evaluated. Finally, the results obtained provide essential information about the effect of the layer thickness, the residual stresses, and the resilience modulus on the cohesive/adhesive strength in FeB/Fe2B systems.

Educational Brief: Using Space for a Better Foundation on Earth Mechanics of Granular Materials

NASA Technical Reports Server (NTRS)

Dooling, Dave (Editor)

2002-01-01

Soils are three-phase composite materials that consist of soil, solid particles, and voids filled with water and/or air. Based on the particle-size distribution, they are generally classified as fine-grained (clays and plastic silts) and coarse-grained soils (nonplastic silts, sand, and gravel). Soil's resistance to external loadings is mainly derived from friction between particles and cohesion. Friction resistance is due to particles' surface-to-surface friction, interlocking, crushing, rearrangement, and dilation (or expansion) during shearing. Cohesion can be due to chemical cementation between particles, electrostatic and electromagnetic forces, and soil-water reaction and equilibrium. The basic factor responsible for the strength of coarse-grained soils is friction. Cohesion can be ignored. This educational brief focuses on measuring shear strength of sands (typical example of coarse-grained soils) where, for the same material, packing density is a main factor to be considered when one asks about the shear strength value. As the external load is applied, the soil's resistance is attained through shearing resistance, which causes the soil volume to increase (expand) or decrease (compress) depending on the initial packing density.

Relation between social cohesion and team performance in soccer teams.

PubMed

Tziner, Aharon; Nicola, Nicola; Rizac, Anis

2003-02-01

Investigations of the influence on team performance of team composition, in terms of task-related attributes, e.g., personality traits, cognitive abilities, often assumes this relation to be mediated by the strength (intensity) of the interpersonal relations (social cohesion) among team members. However, there has been little empirical examination of how much social cohesion actually affects team outcomes. This preliminary study sought to examine this issue using soccer teams, which have been held to resemble workplace teams. Perceptions of team cohesion were collected from 198 Israeli soccer players (comprising 36 national league teams) during the week preceding their weekly games. A significant correlation was found between the perceptions of social cohesion and the results of the soccer matches, indicating a link between team social cohesion and team performance. Implications of the results, as well as the study's limitations, are discussed, and avenues for research are suggested.

Development of experimental concepts for investigating the strength behavior of fine-grained cohesive soil in the Spacelab/space shuttle zero-g environment

NASA Technical Reports Server (NTRS)

Bonaparte, R.; Mitchell, J. K.

1981-01-01

Three different sets of tests are proposed for the NASA Spacelab experimental program. The first of tests, designed to measure the true cohesion of several different soils, would be carried out in space through use of a specially prepared direct shear apparatus. As part of this first series of tests, it is recommended that a set of drained unconfined compression tests be performed terrestrially on the same soils as tested in space. A form of the direct tension test is planned to measure the true tensile strength of the same types of soils used in the first series of tests. The direct tension tests could be performed terrestrially. The combined results of the direct shear tests, direct tension tests, and unconfined compression tests can be used to construct approximate failure envelopes for the soils tested in the region of the stress origin. Relationships between true cohesion and true tensile strength can also be investigated. In addition, the role of physio-chemical variables should be studied. The third set of tests involves using a multiaxial cubical or true triaxial test apparatus to investigate the influence of gravity induced fabric anisotropy and stress nonhomogeneities on the stress strain behavior of cohesive soils at low effective stress levels. These tests would involve both in space and terrestrial laboratory testing.

U.S. Immigration Policy and the National Interest.

ERIC Educational Resources Information Center

Fauriol, Georges

1984-01-01

The national security of the United States depends upon its domestic strength and international stability. This strength requires an ability to control national borders, the maintenance of an independent foreign policy, a prosperous economy, and a cohesive domestic political environment. Uncontrolled migration is undermining this strength. (RM)

A Study of Three Intrinsic Problems of the Classic Discrete Element Method Using Flat-Joint Model

NASA Astrophysics Data System (ADS)

Wu, Shunchuan; Xu, Xueliang

2016-05-01

Discrete element methods have been proven to offer a new avenue for obtaining the mechanics of geo-materials. The standard bonded-particle model (BPM), a classic discrete element method, has been applied to a wide range of problems related to rock and soil. However, three intrinsic problems are associated with using the standard BPM: (1) an unrealistically low unconfined compressive strength to tensile strength (UCS/TS) ratio, (2) an excessively low internal friction angle, and (3) a linear strength envelope, i.e., a low Hoek-Brown (HB) strength parameter m i . After summarizing the underlying reasons of these problems through analyzing previous researchers' work, flat-joint model (FJM) is used to calibrate Jinping marble and is found to closely match its macro-properties. A parametric study is carried out to systematically evaluate the micro-parameters' effect on these three macro-properties. The results indicate that (1) the UCS/TS ratio increases with the increasing average coordination number (CN) and bond cohesion to tensile strength ratio, but it first decreases and then increases with the increasing crack density (CD); (2) the HB strength parameter m i has positive relationships to the crack density (CD), bond cohesion to tensile strength ratio, and local friction angle, but a negative relationship to the average coordination number (CN); (3) the internal friction angle increases as the crack density (CD), bond cohesion to tensile strength ratio, and local friction angle increase; (4) the residual friction angle has little effect on these three macro-properties and mainly influences post-peak behavior. Finally, a new calibration procedure is developed, which not only addresses these three problems, but also considers the post-peak behavior.

Flowability parameters for chopped switchgrass, wheat straw and corn stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chevanan, Nehru; Womac, A.R.; Bitra, V.S.P.

2009-02-01

A direct shear cell to measure the shear strength and flow properties of chopped switchgrass, wheat straw, and corn stover was designed, fabricated, and tested. Yield loci (r2=0.99) determined at pre-consolidation pressures of 3.80 kPa and 5.02 kPa indicated that chopped biomass followed Mohr-Coulomb failure. Normal stress significantly affected the displacement required for shear failure, as well as the friction coefficient values for all three chopped biomass types. Displacement at shear failure ranged from 30 to 80 mm, and depended on pre-consolidation pressure, normal stress, and particle size. Friction coefficient was inversely related to normal stress, and was highest formore » chopped corn stover. Also, chopped corn stover exhibited the highest angle of internal friction, unconfined yield strength, major consolidation strength, and cohesive strength, all of which indicated increased challenges in handling chopped corn stover. The measured angle of internal friction and cohesive strength indicated that chopped biomass cannot be handled by gravity alone. The measured angle of internal friction and cohesive strength were 43 and 0.75 kPa for chopped switchgrass; 44 and 0.49 kPa for chopped wheat straw; and 48 and 0.82 kPa for chopped corn stover. Unconfined yield strength and major consolidation strength used for characterization of bulk flow materials and design of hopper dimensions were 3.4 and 10.4 kPa for chopped switchgrass; 2.3 and 9.6 kPa for chopped wheat straw and 4.2 and 11.8 kPa for chopped corn stover. These results are useful for development of efficient handling, storage, and transportation systems for biomass in biorefineries.« less

Geotechnical properties of municipal solid waste at different phases of biodegradation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reddy, Krishna R., E-mail: kreddy@uic.edu; Hettiarachchi, Hiroshan, E-mail: hiroshan@ltu.edu; Gangathulasi, Janardhanan, E-mail: jganga2@uic.edu

Highlights: > Degraded synthetic municipal solid waste (MSW) anaerobically in controlled bench-scale reactors. > Performed laboratory tests to determine geotechnical properties of MSW at different phases of degradation. > Hydraulic conductivity decreased by two orders of magnitude due to degradation. > Compression ratio reduced from 0.34 for initial fresh waste to 0.15 for the mostly degraded waste. > Friction angle reduced, but cohesion increased with degradation. - Abstract: This paper presents the results of laboratory investigation conducted to determine the variation of geotechnical properties of synthetic municipal solid waste (MSW) at different phases of degradation. Synthetic MSW samples were preparedmore » based on the composition of MSW generated in the United States and were degraded in bioreactors with leachate recirculation. Degradation of the synthetic MSW was quantified based on the gas composition and organic content, and the samples exhumed from the bioreactor cells at different phases of degradation were tested for the geotechnical properties. Hydraulic conductivity, compressibility and shear strength of initial and degraded synthetic MSW were all determined at constant initial moisture content of 50% on wet weight basis. Hydraulic conductivity of synthetic MSW was reduced by two orders of magnitude due to degradation. Compression ratio was reduced from 0.34 for initial fresh waste to 0.15 for the mostly degraded waste. Direct shear tests showed that the fresh and degraded synthetic MSW exhibited continuous strength gain with increase in horizontal deformation, with the cohesion increased from 1 kPa for fresh MSW to 16-40 kPa for degraded MSW and the friction angle decreased from 35{sup o} for fresh MSW to 28{sup o} for degraded MSW. During the triaxial tests under CU condition, the total strength parameters, cohesion and friction angle, were found to vary from 21 to 57 kPa and 1{sup o} to 9{sup o}, respectively, while the effective strength parameters, cohesion and friction angle varied from 18 to 56 kPa and from 1{sup o} to 11{sup o}, respectively. Similar to direct shear test results, as the waste degrades an increase in cohesion and slight decrease in friction angle was observed. Decreased friction angle and increased cohesion with increased degradation is believed to be due to the highly cohesive nature of the synthetic MSW. Variation of synthetic MSW properties from this study also suggests that significant changes in geotechnical properties of MSW can occur due to enhanced degradation induced by leachate recirculation.« less

A Heuristic FORTRAN Model of the Identification and Allocation of CONUS (Continental United States) Prime BEEF (Base Engineer Emergency Forces) Forces in Support of Theater OPlan (Operation Plan) Requirements.

DTIC Science & Technology

1983-09-01

and status systems (Albanese, 1981; Griffin, 1982; Lott & Lott, 1971). Group cohesiveness and norms, according to Wallace and Szilagyi (1982), were the... Wallace & Szilagyi , 1982): 1. The major difference between high and low cohesive groups would be how closely members conform to group norms ; and 2. Group...performance would be influenced not only by cohesiveness, but also by the level or strength of group norms. Research by Wallace and Szilagyi (1982

On the identification of cohesive parameters for printed metal-polymer interfaces

NASA Astrophysics Data System (ADS)

Heinrich, Felix; Langner, Hauke H.; Lammering, Rolf

2017-05-01

The mechanical behavior of printed electronics on fiber reinforced composites is investigated. A methodology based on cohesive zone models is employed, considering interfacial strengths, stiffnesses and critical strain energy release rates. A double cantilever beam test and an end notched flexure test are carried out to experimentally determine critical strain energy release rates under fracture modes I and II. Numerical simulations are performed in Abaqus 6.13 to model both tests. Applying the simulations, an inverse parameter identification is run to determine the full set of cohesive parameters.

Fast determination of structurally cohesive subgroups in large networks

PubMed Central

Sinkovits, Robert S.; Moody, James; Oztan, B. Tolga; White, Douglas R.

2016-01-01

Structurally cohesive subgroups are a powerful and mathematically rigorous way to characterize network robustness. Their strength lies in the ability to detect strong connections among vertices that not only have no neighbors in common, but that may be distantly separated in the graph. Unfortunately, identifying cohesive subgroups is a computationally intensive problem, which has limited empirical assessments of cohesion to relatively small graphs of at most a few thousand vertices. We describe here an approach that exploits the properties of cliques, k-cores and vertex separators to iteratively reduce the complexity of the graph to the point where standard algorithms can be used to complete the analysis. As a proof of principle, we apply our method to the cohesion analysis of a 29,462-vertex biconnected component extracted from a 128,151-vertex co-authorship data set. PMID:28503215

Influence of heat treatment on bond strength and corrosion resistance of sol-gel derived bioglass-ceramic coatings on magnesium alloy.

PubMed

Shen, Sibo; Cai, Shu; Xu, Guohua; Zhao, Huan; Niu, Shuxin; Zhang, Ruiyue

2015-05-01

In this study, bioglass-ceramic coatings were prepared on magnesium alloy substrates through sol-gel dip-coating route followed by heat treatment at the temperature range of 350-500°C. Structure evolution, bond strength and corrosion resistance of samples were studied. It was shown that increasing heat treatment temperature resulted in denser coating structure as well as increased interfacial residual stress. A failure mode transition from cohesive to adhesive combined with a maximum on the measured bond strength together suggested that heat treatment enhanced the cohesion strength of coating on the one hand, while deteriorated the adhesion strength of coating/substrate on the other, thus leading to the highest bond strength of 27.0MPa for the sample heat-treated at 450°C. This sample also exhibited the best corrosion resistance. Electrochemical tests revealed that relative dense coating matrix and good interfacial adhesion can effectively retard the penetration of simulated body fluid through the coating, thus providing excellent protection for the underlying magnesium alloy. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evolution of fault zones in carbonates with mechanical stratigraphy - Insights from scale models using layered cohesive powder

NASA Astrophysics Data System (ADS)

van Gent, Heijn W.; Holland, Marc; Urai, Janos L.; Loosveld, Ramon

2010-09-01

We present analogue models of the formation of dilatant normal faults and fractures in carbonate fault zones, using cohesive hemihydrate powder (CaSO 4·½H 2O). The evolution of these dilatant fault zones involves a range of processes such as fragmentation, gravity-driven breccia transport and the formation of dilatant jogs. To allow scaling to natural prototypes, extensive material characterisation was done. This showed that tensile strength and cohesion depend on the state of compaction, whereas the friction angle remains approximately constant. In our models, tensile strength of the hemihydrate increases with depth from 9 to 50 Pa, while cohesion increases from 40 to 250 Pa. We studied homogeneous and layered material sequences, using sand as a relatively weak layer and hemihydrate/graphite mixtures as a slightly stronger layer. Deformation was analyzed by time-lapse photography and Particle Image Velocimetry (PIV) to calculate the evolution of the displacement field. With PIV the initial, predominantly elastic deformation and progressive localization of deformation are observed in detail. We observed near-vertical opening-mode fractures near the surface. With increasing depth, dilational shear faults were dominant, with releasing jogs forming at fault-dip variations. A transition to non-dilatant shear faults was observed near the bottom of the model. In models with mechanical stratigraphy, fault zones are more complex. The inferred stress states and strengths in different parts of the model agree with the observed transitions in the mode of deformation.

Coseismic landslides reveal near-surface rock strength in a high-relief tectonically active setting

USGS Publications Warehouse

Gallen, Sean F.; Clark, Marin K.; Godt, Jonathan W.

2014-01-01

We present quantitative estimates of near-surface rock strength relevant to landscape evolution and landslide hazard assessment for 15 geologic map units of the Longmen Shan, China. Strength estimates are derived from a novel method that inverts earthquake peak ground acceleration models and coseismic landslide inventories to obtain material proper- ties and landslide thickness. Aggregate rock strength is determined by prescribing a friction angle of 30° and solving for effective cohesion. Effective cohesion ranges are from 70 kPa to 107 kPa for 15 geologic map units, and are approximately an order of magnitude less than typical laboratory measurements, probably because laboratory tests on hand-sized specimens do not incorporate the effects of heterogeneity and fracturing that likely control near-surface strength at the hillslope scale. We find that strength among the geologic map units studied varies by less than a factor of two. However, increased weakening of units with proximity to the range front, where precipitation and active fault density are the greatest, suggests that cli- matic and tectonic factors overwhelm lithologic differences in rock strength in this high-relief tectonically active setting.

The Influence of SAND’s Gradation and Clay Content of Direct Sheart Test on Clayey Sand

NASA Astrophysics Data System (ADS)

Wibisono, Gunawan; Agus Nugroho, Soewignjo; Umam, Khairul

2018-03-01

The shear strength of clayey-sand can be affected by several factors, e.g. gradation, density, moisture content, and the percentage of clay and sand fraction. The same percentage of clay and sand fraction in clayey-sand mixtures may have different shear strengths due to those factors. This research aims to study the effect of clay content on sand that cause the change of its shear strength. Samples consisted of different clay and sand fractions were reconstituted at a certain moisture content. Sand fractions varied from well-graded to poorly-graded sand. Shear strength was measured in terms of the direct shear test. Prior to the test, surcharge loads were applied to represent overburden pressures. Shear strength results and their components (i.e. Cohesion and internal angle of friction) were correlated with physical properties of samples (i.e. grading coefficient of curvature, coefficient of uniformity, and density). Results showed that samples classified as well-graded and dense sand had higher shear strength. In the other hand, the shear strengths decreased when the mixtures became poorly-graded and less dense. The inclusion of the clay fraction increased cohesion component and decreased internal angle of friction.

Archean Microbial Mat Communities

NASA Astrophysics Data System (ADS)

Tice, Michael M.; Thornton, Daniel C. O.; Pope, Michael C.; Olszewski, Thomas D.; Gong, Jian

2011-05-01

Much of the Archean record of microbial communities consists of fossil mats and stromatolites. Critical physical emergent properties governing the evolution of large-scale (centimeters to meters) topographic relief on the mat landscape are (a) mat surface roughness relative to the laminar sublayer and (b) cohesion. These properties can be estimated for fossil samples under many circumstances. A preliminary analysis of Archean mat cohesion suggests that mats growing in shallow marine environments from throughout this time had cohesions similar to those of modern shallow marine mats. There may have been a significant increase in mat strength at the end of the Archean.

The importance of root strength and deterioration rates upon edaphic stability in steepland forests

Treesearch

C. O' Loughlin; R. R. Ziemer

1982-01-01

Abstract - The additional strength provided by roots to the soil is generally considered to be in the form of a cohesive strength C which may range in magnitude from 1 kPa to 20 kPa. Studies of the tensile strength of tree roots show that small roots sampled from living trees range in mean tensile strength from about 10 MPa to about 60 MPa. After tree...

Strength Estimation for Hydrate-Bearing Sediments From Direct Shear Tests of Hydrate-Bearing Sand and Silt

NASA Astrophysics Data System (ADS)

Liu, Zhichao; Dai, Sheng; Ning, Fulong; Peng, Li; Wei, Houzhen; Wei, Changfu

2018-01-01

Safe and economic methane gas production, as well as the replacement of methane while sequestering carbon in natural hydrate deposits, requires enhanced geomechanical understanding of the strength and volume responses of hydrate-bearing sediments during shear. This study employs a custom-made apparatus to investigate the mechanical and volumetric behaviors of carbon dioxide hydrate-bearing sediments subjected to direct shear. The results show that both peak and residual strengths increase with increased hydrate saturation and vertical stress. Hydrate contributes mainly the cohesion and dilatancy constraint to the peak strength of hydrate-bearing sediments. The postpeak strength reduction is more evident and brittle in specimens with higher hydrate saturation and under lower stress. Significant strength reduction after shear failure is expected in silty sediments with high hydrate saturation Sh ≥ 0.65. Hydrate contribution to the residual strength is mainly by increasing cohesion at low hydrate saturation and friction at high hydrate saturation. Stress state and hydrate saturation are dominating both the stiffness and the strength of hydrate-bearing sediments; thus, a wave velocity-based peak strength prediction model is proposed and validated, which allows for precise estimation of the shear strength of hydrate-bearing sediments through acoustic logging data. This method is advantageous to geomechanical simulators, particularly when the experimental strength data of natural samples are not available.

Effect of thermally growth oxides (TGO) on adhesion strength for high purity yitria stabilised zirconia (YSZ) and rare - Earth lanthanum zirconates (LZ) multilayer thermal barrier coating before and after isothermal heat treatment

NASA Astrophysics Data System (ADS)

Yunus, Salmi Mohd; Johari, Azril Dahari; Husin, Shuib

2017-12-01

Investigation on the effect of Thermally Growth Oxides (TGO) on the adhesion strength for thermal barrier coating (TBC) was carried out. The TBC under studied was the multilayer systems which consist of NiCrAlY bond coat and YSZ/LZ ceramic coating deposited on Ni-based superalloy substrates. The development of thermally growth oxides (TGO) for both TBC systems after isothermal heat treatment was measured. Isothermal heat treatment was carried out at 1100 ˚C for 100 hours to age the samples. ASTM D4541: Standard Test Method for Pull-off Strength of Coatings using Portable Adhesion Tester was used to measure the adhesion strength of both TBC systems before and after heat treatment. The effect of the developed TGO on the measured adhesion strength was examined and correlation between them was established individually for both TBC systems. The failure mechanism of the both system was also identified; either cohesive or adhesive or the combination of both. The results showed that TGO has more than 50% from the bond coat layer for rare-earth LZ system compared to the typical YSZ system, which was less than 10 % from the bond coat layer. This leads to the lower adhesion strength of rare-earth LZ coating system compared to typical YSZ system. Failure mechanism during the pull-off test also was found to be different for both TBC systems. The typical YSZ system experienced cohesive failure whereas the rare-earth LZ system experienced the combination of cohesive and adhesive failure.

Reply to "Comment on `Flow of wet granular materials: A numerical study' "

NASA Astrophysics Data System (ADS)

Khamseh, Saeed; Roux, Jean-Noël; Chevoir, François

2017-07-01

In his Comment on our paper [Phys. Rev. E 92, 022201 (2015), 10.1103/PhysRevE.92.022201], Chareyre criticizes, as inaccurate, the simple approach we adopted to explain the strong enhancement of the quasistatic shear strength of the material caused by capillary cohesion. He also observes that a similar form of the "effective stress" approach, accounting for the capillary shear stress, which we neglected, results in a quantitatively correct prediction of this yield stress. We agree with these remarks, which we deem quite relevant and valuable. We nevertheless point out that the initial approximation, despite ˜25 % errors on shear strength in the worst cases, provides a convenient estimate of the Mohr-Coulomb cohesion of the material, which is directly related to the coordination number. We argue that the effective stress assumption, despite its surprising success in the range of states explored in Khamseh et al. [Phys. Rev. E 92, 022201 (2015), 10.1103/PhysRevE.92.022201], is bound to fail in strongly cohesion-dominated material states.

Rheology of granular materials composed of crushable particles.

PubMed

Nguyen, Duc-Hanh; Azéma, Émilien; Sornay, Philippe; Radjaï, Farhang

2018-04-11

We investigate sheared granular materials composed of crushable particles by means of contact dynamics simulations and the bonded-cell model for particle breakage. Each particle is paved by irregular cells interacting via cohesive forces. In each simulation, the ratio of the internal cohesion of particles to the confining pressure, the relative cohesion, is kept constant and the packing is subjected to biaxial shearing. The particles can break into two or more fragments when the internal cohesive forces are overcome by the action of compressive force chains between particles. The particle size distribution evolves during shear as the particles continue to break. We find that the breakage process is highly inhomogeneous both in the fragment sizes and their locations inside the packing. In particular, a number of large particles never break whereas a large number of particles are fully shattered. As a result, the packing keeps the memory of its initial particle size distribution, whereas a power-law distribution is observed for particles of intermediate size due to consecutive fragmentation events whereby the memory of the initial state is lost. Due to growing polydispersity, dense shear bands are formed inside the packings and the usual dilatant behavior is reduced or cancelled. Hence, the stress-strain curve no longer passes through a peak stress, and a progressive monotonic evolution towards a pseudo-steady state is observed instead. We find that the crushing rate is controlled by the confining pressure. We also show that the shear strength of the packing is well expressed in terms of contact anisotropies and force anisotropies. The force anisotropy increases while the contact orientation anisotropy declines for increasing internal cohesion of the particles. These two effects compensate each other so that the shear strength is nearly independent of the internal cohesion of particles.

Crack blunting and the strength of soft elastic solids

NASA Astrophysics Data System (ADS)

Hui, C.-Y.; Jagota, A.; Bennison, S. J.; Londono, J. D.

2003-06-01

When a material is so soft that the cohesive strength (or adhesive strength, in the case of interfacial fracture) exceeds the elastic modulus of the material, we show that a crack will blunt instead of propagating. Large-deformation finite-element model (FEM) simulations of crack initiation, in which the debonding processes are quantified using a cohesive zone model, are used to support this hypothesis. An approximate analytic solution, which agrees well with the FEM simulation, gives additional insight into the blunting process. The consequence of this result on the strength of soft, rubbery materials is the main topic of this paper. We propose two mechanisms by which crack growth can occur in such blunted regions. We have also performed experiments on two different elastomers to demonstrate elastic blunting. In one system, we present some details on a void growth mechanism for ultimate failure, post-blunting. Finally, we demonstrate how crack blunting can shed light on some long-standing problems in the area of adhesion and fracture of elastomers.

Individual and family strengths: an examination of the relation to disease management and metabolic control in youth with type 1 diabetes.

PubMed

Mackey, Eleanor Race; Hilliard, Marisa E; Berger, Sarah Shafer; Streisand, Randi; Chen, Rusan; Holmes, Clarissa

2011-12-01

We examined the association of youths' positive qualities, family cohesion, disease management, and metabolic control in Type 1 diabetes. Two-hundred fifty-seven youth-parent dyads completed the Family Cohesion subscale of the Family Environment Scale, the Diabetes Behavior Rating Scale, 24-hour diabetes interview, and youth completed the Positive Qualities subscale of the Youth Self Report (YSR-PQ). Structural equation modeling demonstrated that YSR-PQ scores were associated with metabolic control mediated by associations with more family cohesion and better disease management. That is, youth with higher YSR-PQ scores had more cohesive families, better disease management, and, indirectly, better metabolic control. Family cohesion was indirectly associated with better metabolic control mediated by its association with better disease management, but not mediated by its association with YSR-PQ scores. Youth who reported more positive qualities, as measured by the YSR-PQ subscale, had better disease management and metabolic control through the association with more family cohesion. However, the current results did not support an alternative hypothesis that cohesive families display better diabetes management mediated by higher YSR-PQ scores.

Random analysis of bearing capacity of square footing using the LAS procedure

NASA Astrophysics Data System (ADS)

Kawa, Marek; Puła, Wojciech; Suska, Michał

2016-09-01

In the present paper, a three-dimensional problem of bearing capacity of square footing on random soil medium is analyzed. The random fields of strength parameters c and φ are generated using LAS procedure (Local Average Subdivision, Fenton and Vanmarcke 1990). The procedure used is re-implemented by the authors in Mathematica environment in order to combine it with commercial program. Since the procedure is still tested the random filed has been assumed as one-dimensional: the strength properties of soil are random in vertical direction only. Individual realizations of bearing capacity boundary-problem with strength parameters of medium defined the above procedure are solved using FLAC3D Software. The analysis is performed for two qualitatively different cases, namely for the purely cohesive and cohesive-frictional soils. For the latter case the friction angle and cohesion have been assumed as independent random variables. For these two cases the random square footing bearing capacity results have been obtained for the range of fluctuation scales from 0.5 m to 10 m. Each time 1000 Monte Carlo realizations have been performed. The obtained results allow not only the mean and variance but also the probability density function to be estimated. An example of application of this function for reliability calculation has been presented in the final part of the paper.

CONSTRAINTS ON THE PHYSICAL PROPERTIES OF MAIN BELT COMET P/2013 R3 FROM ITS BREAKUP EVENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirabayashi, Masatoshi; Sánchez, Diego Paul; Gabriel, Travis

2014-07-01

Jewitt et al. recently reported that main belt comet P/2013 R3 experienced a breakup, probably due to rotational disruption, with its components separating on mutually hyperbolic orbits. We propose a technique for constraining physical properties of the proto-body, especially the initial spin period and cohesive strength, as a function of the body's estimated size and density. The breakup conditions are developed by combining mutual orbit dynamics of the smaller components and the failure condition of the proto-body. Given a proto-body with a bulk density ranging from 1000 kg m{sup –3} to 1500 kg m{sup –3} (a typical range of the bulk density of C-type asteroids),more » we obtain possible values of the cohesive strength (40-210 Pa) and the initial spin state (0.48-1.9 hr). From this result, we conclude that although the proto-body could have been a rubble pile, it was likely spinning beyond its gravitational binding limit and would have needed cohesive strength to hold itself together. Additional observations of P/2013 R3 will enable stronger constraints on this event, and the present technique will be able to give more precise estimates of its internal structure.« less

Response of Partially Saturated Non-cohesive Soils

NASA Astrophysics Data System (ADS)

Świdziński, Waldemar; Mierczyński, Jacek; Mikos, Agata

2017-12-01

This paper analyses and discusses experimental results of undrained triaxial tests. The tests were performed on non-cohesive partially saturated soil samples subjected to monotonic and cyclic loading. The tests were aimed at determining the influence of saturation degree on soil's undrained response (shear strength, excess pore pressure generation). The saturation of samples was monitored by checking Skempton's parameter B. Additionally, seismic P-wave velocity measurements were carried out on samples characterized by various degrees of saturation. The tests clearly showed that liquefaction may also take place in non-cohesive soils that are not fully saturated and that the liquefaction potential of such soils strongly depends on the B parameter.

Factors affecting the shear strength behavior of municipal solid wastes.

PubMed

Pulat, Hasan Firat; Yukselen-Aksoy, Yeliz

2017-11-01

In this study, the shear strength behavior of European (E-1), Turkey (T-1), and United States of America (U-1) average synthetic municipal solid waste (MSW) compositions were investigated. The large-scale direct shear tests were conducted using fresh and aged MSW samples collected from the Manisa Landfill. The natural samples' test results were compared with synthetic samples. The affecting factors such as ageing, waste composition, and waste type (synthetic and natural) on the shear strength of MSWs were investigated. The effect of composition was evaluated using three main and six modified synthetic MSW compositions. In addition to the synthetic fresh MSW samples, synthetic aged samples were also used. Angle of shearing resistance decreased with increasing organic content whereas cohesion intercept increased with increasing organic content. The fresh and aged wastes with higher coarse fraction lead to a higher angle of shearing resistance. The synthetic aged samples had higher internal friction angles but lower cohesion values than the synthetic fresh samples. Waste with average European composition had the highest internal friction angle as it has the highest fibrous content. On the other hand, the highest cohesion belonged to the Turkey composition, which had the highest organic matter ratio. The main differences between E-1, T-1 and U-1 samples in terms of compositions were observed. The results of this study indicated that shear strength of waste significantly depends on composition and hence a site specific evaluation is recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

Geotechnical properties of cemented sands in steep slopes

USGS Publications Warehouse

Collins, B.D.; Sitar, N.

2009-01-01

An investigation into the geotechnical properties specific to assessing the stability of weakly and moderately cemented sand cliffs is presented. A case study from eroding coastal cliffs located in central California provides both the data and impetus for this study. Herein, weakly cemented sand is defined as having an unconfined compressive strength (UCS) of less than 100 kPa, and moderately cemented sand is defined as having UCS between 100 and 400 kPa. Testing shows that both materials fail in a brittle fashion and can be modeled effectively using linear Mohr-Coulomb strength parameters, although for weakly cemented sands, curvature of the failure envelope is more evident with decreasing friction and increasing cohesion at higher confinement. Triaxial tests performed to simulate the evolving stress state of an eroding cliff, using a reduction in confinement-type stress path, result in an order of magnitude decrease in strain at failure and a more brittle response. Tests aimed at examining the influence of wetting on steep slopes show that a 60% decrease in UCS, a 50% drop in cohesion, and 80% decrease in the tensile strength occurs in moderately cemented sand upon introduction to water. In weakly cemented sands, all compressive, cohesive, and tensile strength is lost upon wetting and saturation. The results indicate that particular attention must be given to the relative level of cementation, the effects of groundwater or surficial seepage, and the small-scale strain response when performing geotechnical slope stability analyses on these materials. ?? 2009 ASCE.

Description of new dry granular materials of variable cohesion and friction coefficient: Implications for laboratory modeling of the brittle crust

NASA Astrophysics Data System (ADS)

Abdelmalak, M. M.; Bulois, C.; Mourgues, R.; Galland, O.; Legland, J.-B.; Gruber, C.

2016-08-01

Cohesion and friction coefficient are fundamental parameters for scaling brittle deformation in laboratory models of geological processes. However, they are commonly not experimental variable, whereas (1) rocks range from cohesion-less to strongly cohesive and from low friction to high friction and (2) strata exhibit substantial cohesion and friction contrasts. This brittle paradox implies that the effects of brittle properties on processes involving brittle deformation cannot be tested in laboratory models. Solving this paradox requires the use of dry granular materials of tunable and controllable brittle properties. In this paper, we describe dry mixtures of fine-grained cohesive, high friction silica powder (SP) and low-cohesion, low friction glass microspheres (GM) that fulfill this requirement. We systematically estimated the cohesions and friction coefficients of mixtures of variable proportions using two independent methods: (1) a classic Hubbert-type shear box to determine the extrapolated cohesion (C) and friction coefficient (μ), and (2) direct measurements of the tensile strength (T0) and the height (H) of open fractures to calculate the true cohesion (C0). The measured values of cohesion increase from 100 Pa for pure GM to 600 Pa for pure SP, with a sub-linear trend of the cohesion with the mixture GM content. The two independent cohesion measurement methods, from shear tests and tension/extensional tests, yield very similar results of extrapolated cohesion (C) and show that both are robust and can be used independently. The measured values of friction coefficients increase from 0.5 for pure GM to 1.05 for pure SP. The use of these granular material mixtures now allows testing (1) the effects of cohesion and friction coefficient in homogeneous laboratory models and (2) testing the effect of brittle layering on brittle deformation, as demonstrated by preliminary experiments. Therefore, the brittle properties become, at last, experimental variables.

Drinking water biofilm cohesiveness changes under chlorination or hydrodynamic stress.

PubMed

Mathieu, L; Bertrand, I; Abe, Y; Angel, E; Block, J C; Skali-Lami, S; Francius, G

2014-05-15

Attempts at removal of drinking water biofilms rely on various preventive and curative strategies such as nutrient reduction in drinking water, disinfection or water flushing, which have demonstrated limited efficiency. The main reason for these failures is the cohesiveness of the biofilm driven by the physico-chemical properties of its exopolymeric matrix (EPS). Effective cleaning procedures should break up the matrix and/or change the elastic properties of bacterial biofilms. The aim of this study was to evaluate the change in the cohesive strength of two-month-old drinking water biofilms under increasing hydrodynamic shear stress τw (from ∼0.2 to ∼10 Pa) and shock chlorination (applied concentration at T0: 10 mg Cl2/L; 60 min contact time). Biofilm erosion (cell loss per unit surface area) and cohesiveness (changes in the detachment shear stress and cluster volumes measured by atomic force microscopy (AFM)) were studied. When rapidly increasing the hydrodynamic constraint, biofilm removal was found to be dependent on a dual process of erosion and coalescence of the biofilm clusters. Indeed, 56% of the biofilm cells were removed with, concomitantly, a decrease in the number of the 50-300 μm(3) clusters and an increase in the number of the smaller (i.e., <50 μm(3)) and larger (i.e., >600 μm(3)) ones. Moreover, AFM evidenced the strengthening of the biofilm structure along with the doubling of the number of contact points, NC, per cluster volume unit following the hydrodynamic disturbance. This suggests that the compactness of the biofilm exopolymers increases with hydrodynamic stress. Shock chlorination removed cells (-75%) from the biofilm while reducing the volume of biofilm clusters. Oxidation stress resulted in a decrease in the cohesive strength profile of the remaining drinking water biofilms linked to a reduction in the number of contact points within the biofilm network structure in particular for the largest biofilm cluster volumes (>200 μm(3)). Changes in the cohesive strength of drinking water biofilms subsequent to cleaning/disinfection operations call into question the effectiveness of cleaning-in-place procedures. The combined alternating use of oxidation and shear stress sequences needs to be investigated as it could be an important adjunct to improving biofilm removal/reduction procedures. Copyright © 2014 Elsevier Ltd. All rights reserved.

Two-scale modeling of joining of the aluminum alloys by a cohesive zone element technique

NASA Astrophysics Data System (ADS)

Zuo, Yinan; Wulfinghoff, Stephan; Reese, Stefanie

2016-10-01

The roll bonding of aluminum sheets is numerically investigated. In the first part of the paper, a cohesive zone element formulation in the framework of zero-thickness interface elements is developed. Based on a traction-separation law, this enables the modeling of bonding and debonding on both macroscale and microscale. Simulations on microscale are done to show the mechanism of bonding and the influence of different factors on the bonding strength.

Planetesimal Formation in the Warm, Inner Disk: Experiments with Tempered Dust

NASA Astrophysics Data System (ADS)

de Beule, Caroline; Landers, Joachim; Salamon, Soma; Wende, Heiko; Wurm, Gerhard

2017-03-01

It is an open question how elevated temperatures in the inner parts of protoplanetary disks influence the formation of planetesimals. We approach this problem here by studying the tensile strength of granular beds with dust samples tempered at different temperatures. We find via laboratory experiments that tempering at increasing temperatures is correlated with an increase in cohesive forces. We studied dust samples of palagonite (JSC Mars-1a) which were tempered for up to 200 hr at temperatures between 600 and 1200 K, and measured the relative tensile strengths of highly porous dust layers once the samples cooled to room temperature. Tempering increases the tensile strength from 800 K upwards. This change is accompanied by mineral transformations, the formation of iron oxide crystallites as analyzed by Mössbauer spectroscopy, changes in the number size distribution, and the morphology of the surface visible as cracks in larger grains. These results suggest a difference in the collisional evolution toward larger bodies with increasing temperature as collisional growth is fundamentally based on cohesion. While high temperatures might also increase sticking (not studied here), compositional evolution will already enhance the cohesion and the possibility of growing larger aggregates on the way toward planetesimals. This might lead to a preferred in situ formation of inner planets and explain the observed presence of dense inner planetary systems.

Planetesimal Formation in the Warm, Inner Disk: Experiments with Tempered Dust

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Beule, Caroline; Landers, Joachim; Salamon, Soma

2017-03-01

It is an open question how elevated temperatures in the inner parts of protoplanetary disks influence the formation of planetesimals. We approach this problem here by studying the tensile strength of granular beds with dust samples tempered at different temperatures. We find via laboratory experiments that tempering at increasing temperatures is correlated with an increase in cohesive forces. We studied dust samples of palagonite (JSC Mars-1a) which were tempered for up to 200 hr at temperatures between 600 and 1200 K, and measured the relative tensile strengths of highly porous dust layers once the samples cooled to room temperature. Temperingmore » increases the tensile strength from 800 K upwards. This change is accompanied by mineral transformations, the formation of iron oxide crystallites as analyzed by Mössbauer spectroscopy, changes in the number size distribution, and the morphology of the surface visible as cracks in larger grains. These results suggest a difference in the collisional evolution toward larger bodies with increasing temperature as collisional growth is fundamentally based on cohesion. While high temperatures might also increase sticking (not studied here), compositional evolution will already enhance the cohesion and the possibility of growing larger aggregates on the way toward planetesimals. This might lead to a preferred in situ formation of inner planets and explain the observed presence of dense inner planetary systems.« less

Influence of Powder Morphology and Microstructure on the Cold Spray and Mechanical Properties of Ti6Al4V Coatings

NASA Astrophysics Data System (ADS)

Munagala, Venkata Naga Vamsi; Akinyi, Valary; Vo, Phuong; Chromik, Richard R.

2018-06-01

The powder microstructure and morphology has significant influence on the cold sprayability of Ti6Al4V coatings. Here, we compare the cold sprayability and properties of coatings obtained from Ti6Al4V powders of spherical morphology (SM) manufactured using plasma gas atomization and irregular morphology (IM) manufactured using the Armstrong process. Coatings deposited using IM powders had negligible porosity and better properties compared to coatings deposited using SM powders due to higher particle impact velocities, porous surface morphology and more deformable microstructure. To evaluate the cohesive strength, multi-scale indentation was performed and hardness loss parameter was calculated. Coatings deposited using SM powders exhibited poor cohesive strength compared to coatings deposited using IM powders. Images of the residual indents showed de-bonding and sliding of adjacent splats in the coatings deposited using SM powders irrespective of the load. Coatings deposited using IM powders showed no evidence of de-bonding at low loads. At high loads, splat de-bonding was observed resulting in hardness loss despite negligible porosity. Thus, while the powders from Armstrong process lead to a significant improvement in sprayability and coating properties, further optimization of powder and cold spray process will be required as well as consideration of post-annealing treatments to obtain acceptable cohesive strength.

Anisotropic Failure Strength of Shale with Increasing Confinement: Behaviors, Factors and Mechanism.

PubMed

Cheng, Cheng; Li, Xiao; Qian, Haitao

2017-11-15

Some studies reported that the anisotropic failure strength of shale will be weakened by increasing confinement. In this paper, it is found that there are various types of anisotropic strength behaviors. Four types of anisotropic strength ratio ( S A 1 ) behaviors and three types of anisotropic strength difference ( S A 2 ) behaviors have been classified based on laboratory experiments on nine groups of different shale samples. The cohesion c w and friction angle ϕ w of the weak planes are proven to be two dominant factors according to a series of bonded-particle discrete element modelling analyses. It is observed that shale is more prone to a slight increase of S A 1 and significant increase of S A 2 with increasing confinement for higher cohesion c w and lower to medium friction angle ϕ w . This study also investigated the mechanism of the anisotropic strength behaviors with increasing confinement. Owing to different contributions of c w and ϕ w under different confinements, different combinations of c w and ϕ w may have various types of influences on the minimum failure strength with the increasing confinement; therefore, different types of anisotropic behaviors occur for different shale specimens as the confinement increases. These findings are very important to understand the stability of wellbore and underground tunneling in the shale rock mass, and should be helpful for further studies on hydraulic fracture propagations in the shale reservoir.

Anisotropic Failure Strength of Shale with Increasing Confinement: Behaviors, Factors and Mechanism

PubMed Central

Cheng, Cheng; Li, Xiao; Qian, Haitao

2017-01-01

Some studies reported that the anisotropic failure strength of shale will be weakened by increasing confinement. In this paper, it is found that there are various types of anisotropic strength behaviors. Four types of anisotropic strength ratio (SA1) behaviors and three types of anisotropic strength difference (SA2) behaviors have been classified based on laboratory experiments on nine groups of different shale samples. The cohesion cw and friction angle ϕw of the weak planes are proven to be two dominant factors according to a series of bonded-particle discrete element modelling analyses. It is observed that shale is more prone to a slight increase of SA1 and significant increase of SA2 with increasing confinement for higher cohesion cw and lower to medium friction angle ϕw. This study also investigated the mechanism of the anisotropic strength behaviors with increasing confinement. Owing to different contributions of cw and ϕw under different confinements, different combinations of cw and ϕw may have various types of influences on the minimum failure strength with the increasing confinement; therefore, different types of anisotropic behaviors occur for different shale specimens as the confinement increases. These findings are very important to understand the stability of wellbore and underground tunneling in the shale rock mass, and should be helpful for further studies on hydraulic fracture propagations in the shale reservoir. PMID:29140292

Shear strength of wet granular materials: Macroscopic cohesion and effective stress : Discrete numerical simulations, confronted to experimental measurements.

PubMed

Badetti, Michel; Fall, Abdoulaye; Chevoir, François; Roux, Jean-Noël

2018-05-28

Rheometric measurements on assemblies of wet polystyrene beads, in steady uniform quasistatic shear flow, for varying liquid content within the small saturation (pendular) range of isolated liquid bridges, are supplemented with a systematic study by discrete numerical simulations. The numerical results agree quantitatively with the experimental ones provided that the intergranular friction coefficient is set to the value [Formula: see text], identified from the behaviour of the dry material. Shear resistance and solid fraction [Formula: see text] are recorded as functions of the reduced pressure [Formula: see text], which, defined as [Formula: see text], compares stress [Formula: see text], applied in the velocity gradient direction, to the tensile strength [Formula: see text] of the capillary bridges between grains of diameter a, and characterizes cohesion effects. The simplest Mohr-Coulomb relation with [Formula: see text]-independent cohesion c applies as a good approximation for large enough [Formula: see text] (typically [Formula: see text]. Numerical simulations extend to different values of μ and, compared to experiments, to a wider range of [Formula: see text]. The assumption that capillary stresses act similarly to externally applied ones onto the dry granular contact network (effective stresses) leads to very good (although not exact) predictions of the shear strength, throughout the numerically investigated range [Formula: see text] and [Formula: see text]. Thus, the internal friction coefficient [Formula: see text] of the dry material still relates the contact force contribution to stresses, [Formula: see text], while the capillary force contribution to stresses, [Formula: see text], defines a generalized Mohr-Coulomb cohesion c, depending on [Formula: see text] in general. c relates to [Formula: see text] , coordination numbers and capillary force network anisotropy. c increases with liquid content through the pendular regime interval, to a larger extent, the smaller the friction coefficient. The simple approximation ignoring capillary shear stress [Formula: see text] (referred to as the Rumpf formula) leads to correct approximations for the larger saturation range within the pendular regime, but fails to capture the decrease of cohesion for smaller liquid contents.

The variability of root cohesion as an influence on shallow landslide susceptibility in the Oregon Coast Range

USGS Publications Warehouse

Schmidt, K.M.; Roering, J.J.; Stock, J.D.; Dietrich, W.E.; Montgomery, D.R.; Schaub, T.

2001-01-01

Decades of quantitative measurement indicate that roots can mechanically reinforce shallow soils in forested landscapes. Forests, however, have variations in vegetation species and age which can dominate the local stability of landslide-initiation sites. To assess the influence of this variability on root cohesion we examined scarps of landslides triggered during large storms in February and November of 1996 in the Oregon Coast Range and hand-dug soil pits on stable ground. At 41 sites we estimated the cohesive reinforcement to soil due to roots by determining the tensile strength, species, depth, orientation, relative health, and the density of roots ???1 mm in diameter within a measured soil area. We found that median lateral root cohesion ranges from 6.8-23.2 kPa in industrial forests with significant understory and deciduous vegetation to 25.6-94.3 kPa in natural forests dominated by coniferous vegetation. Lateral root cohesion in clearcuts is uniformly ???10 kPa. Some 100-year-old industrial forests have species compositions, lateral root cohesion, and root diameters that more closely resemble 10-year-old clearcuts than natural forests. As such, the influence of root cohesion variability on landslide susceptibility cannot be determined solely from broad age classifications or extrapolated from the presence of one species of vegetation. Furthermore, the anthropogenic disturbance legacy modifies root cohesion for at least a century and should be considered when comparing contemporary landslide rates from industrial forests with geologic background rates.

Molecular interactions of mussel protective coating protein, mcfp-1, from Mytilus californianus.

PubMed

Lu, Qingye; Hwang, Dong Soo; Liu, Yang; Zeng, Hongbo

2012-02-01

Protective coating of the byssus of mussels (Mytilus sp.) has been suggested as a new paradigm of medical coating due to its high extensibility and hardness co-existence without their mutual detriment. The only known biomacromolecule in the extensible and tough coating on the byssus is mussel foot protein-1 (mfp-1), which is made up with positively charged residues (~20 mol%) and lack of negatively charged residues. Here, adhesion and molecular interaction mechanisms of Mytilus californianus foot protein-1 (mcfp-1) from California blue mussel were investigated using a surface forces apparatus (SFA) in buffer solutions of different ionic concentrations (0.2-0.7 M) and pHs (3.0-5.5). Strong and reversible cohesion between opposed positively charged mcfp-1 films was measured in 0.1 M sodium acetate buffer with 0.1 M KNO(3). Cohesion of mcfp-1 was gradually reduced with increasing the ionic strength, but was not changed with pH variations. Oxidation of 3,4-dihydroxyphenylalanine (DOPA) residues of mcfp-1, a key residue for adhesive and coating proteins of mussel, didn't change the cohesion strength of mcfp-1 films, but the addition of chemicals with aromatic groups (i.e., aspirin and 4-methylcatechol) increased the cohesion. These results suggest that the cohesion of mcfp-1 films is mainly mediated by cation-π interactions between the positively charged residues and benzene rings of DOPA and other aromatic amino acids (~20 mol% of total amino acids of mcfp-1), and π-π interactions between the phenyl groups in mcfp-1. The adhesion mechanism obtained for the mcfp-1 proteins provides important insight into the design and development of functional biomaterials and coatings mimicking the extensible and robust mussel cuticle coating. Copyright © 2011 Elsevier Ltd. All rights reserved.

Comparison of Shear Strength Properties for Undisturbed and Reconstituted Parit Nipah Peat, Johor

NASA Astrophysics Data System (ADS)

Azhar, A. T. S.; Norhaliza, W.; Ismail, B.; Abdullah, M. E.; Zakaria, M. N.

2016-11-01

Shear strength of soil is required to determine the soil stability and design the foundations. Peat is known as a soil with complex natural formations which also contributes problems to the researchers, developers, engineers and contractors in constructions and infrastructures. Most researchers conducted experiment and investigation of shear strength on peat using shear box test and simple shear test, but only a few had discovered the behavior of peat using triaxial consolidated undrained test. The aim of this paper is to determine the undrained shear strength properties of reconstituted peat and undisturbed peat of Parit Nipah, Johor for comparison purposes. All the reconstituted peat samples were formed with the size that passed opening sieve 3.35 mm and preconsolidation pressure at 100 kPa. The result of undrained shear strength of reconstituted peat was 21kPa for cohesion with the angle of friction, 41° compare to the undisturbed peat with cohesion 10 kPa and angle of friction, 16°. The undrained shear strength properties result obtained shows that the reconstituted peat has higher strength than undisturbed peat. For relationship deviator stress-strain, σd max and excess pore pressure, Δu, it shows that both of undisturbed and reconstituted gradually increased when σ’ increased, but at the end of the test, the values are slightly dropped. The physical properties of undisturbed and reconstituted peat were also investigated to correlate with the undrained shear strength results.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivakumar Babu, G.L., E-mail: gls@civil.iisc.ernet.in; Lakshmikanthan, P., E-mail: lakshmikanthancp@gmail.com; Santhosh, L.G., E-mail: lgsanthu2006@gmail.com

Highlights: • Shear strength properties of mechanically biologically treated municipal solid waste. • Effect of unit weight and particle size on the shear strength of waste. • Effect of particle size on the strength properties. • Stiffness ratio and the strength ratio of MSW. - Abstract: Strength and stiffness properties of municipal solid waste (MSW) are important in landfill design. This paper presents the results of comprehensive testing of shear strength properties of mechanically biologically treated municipal solid waste (MBT-MSW) in laboratory. Changes in shear strength of MSW as a function of unit weight and particle size were investigated bymore » performing laboratory studies on the MSW collected from Mavallipura landfill site in Bangalore. Direct shear tests, small scale and large scale consolidated undrained and drained triaxial tests were conducted on reconstituted compost reject MSW samples. The triaxial test results showed that the MSW samples exhibited a strain-hardening behaviour and the strength of MSW increased with increase in unit weight. Consolidated drained tests showed that the mobilized shear strength of the MSW increased by 40% for a unit weight increase from 7.3 kN/m{sup 3} to 10.3 kN/m{sup 3} at 20% strain levels. The mobilized cohesion and friction angle ranged from 5 to 9 kPa and 8° to 33° corresponding to a strain level of 20%. The consolidated undrained tests exhibited reduced friction angle values compared to the consolidated drained tests. The friction angle increased with increase in the unit weight from 8° to 55° in the consolidated undrained tests. Minor variations were found in the cohesion values. Relationships for strength and stiffness of MSW in terms of strength and stiffness ratios are developed and discussed. The stiffness ratio and the strength ratio of MSW were found to be 10 and 0.43.« less

Thermal Processing Effects on the Adhesive Strength of PS304 High Temperature Solid Lubricant Coatings

NASA Technical Reports Server (NTRS)

DellaCorte, Christopher; Edmonds, Brian J.; Benoy, Patricia A.

2001-01-01

In this paper the effects of post deposition heat treatments on the cohesive and adhesive strength properties of PS304, a plasma sprayed nickel-chrome based, high temperature solid lubricant coating deposited on stainless steel, are studied. Plasma spray deposited coating samples were exposed in air at temperatures from 432 to 650 C for up to 500 hr to promote residual stress relief, enhance particle to particle bonding and increase coating to substrate bond strength. Coating pull-off strength was measured using a commercial adhesion tester that utilizes 13 mm diameter aluminum pull studs attached to the coating surface with epoxy. Pull off force was automatically recorded and converted to coating pull off strength. As deposited coating samples were also tested as a baseline. The as-deposited (untreated) samples either delaminated at the coating-substrate interface or failed internally (cohesive failure) at about 17 MPa. Samples heat treated at temperatures above 540 C for 100 hr or at 600 C or above for more than 24 hr exhibited strengths above 31 MPa, nearly a two fold increase. Coating failure occurred inside the body of the coating (cohesive failure) for nearly all of the heat-treated samples and only occasionally at the coating substrate interface (adhesive failure). Metallographic analyses of heat-treated coatings indicate that the Nickel-Chromium binder in the PS304 appears to have segregated into two phases, a high nickel matrix phase and a high chromium precipitated phase. Analysis of the precipitates indicates the presence of silicon, a constituent of a flow enhancing additive in the commercial NiCr powder. The exact nature and structure of the precipitate phase is not known. This microstructural change is believed to be partially responsible for the coating strength increase. Diffusion bonding between particles may also be playing a role. Increasing the heat treatment temperature, exposure time or both accelerate the heat treatment process. Preliminary measurements indicate that the heat treatment also results in a one time, permanent coating thickness increase of about 3%. Based upon these results, the incorporation of a heat treatment prior to final finishing has been incorporated in the application process of this coating technology.

A Laboratory Investigation on Shear Strength Behavior of Sandy Soil: Effect of Glass Fiber and Clinker Residue Content

NASA Astrophysics Data System (ADS)

Bouaricha, Leyla; Henni, Ahmed Djafar; Lancelot, Laurent

2017-12-01

A study was undertaken to investigate the shear strength parameters of treated sands reinforced with randomly distributed glass fibers by carrying out direct shear test after seven days curing periods. Firstly, we studied the fiber content and fiber length effect on the peak shear strength on samples. The second part gives a parametric analysis on the effect of glass fiber and clinker residue content on the shear strength parameters for two types of uniform Algerian sands having different particle sizes (Chlef sand and Rass sand) with an average relative density Dr = 50%. Finally, the test results show that the combination of glass fiber and clinker residue content can effectively improve the shear strength parameters of soil in comparison with unreinforced soil. For instance, there is a significant gain for the cohesion and friction angle of reinforced sand of Chlef. Compared to unreinforced sand, the cohesion for sand reinforced with different ratios of clinker residue increased by 4.36 to 43.08 kPa for Chlef sand and by 3.1 to 28.64 kPa for Rass sand. The feature friction angles increased from 38.73° to 43.01° (+4.28°), and after the treatment, clinker residue content of soil evaluated to 5% (WRC = 5%).

Scaling of strength and ductility in bioinspired brick and mortar composites

NASA Astrophysics Data System (ADS)

Wilbrink, David V.; Utz, Marcel; Ritchie, Robert O.; Begley, Matthew R.

2010-11-01

This paper provides scaling relationships between constituent properties and the uniaxial tensile response of synthetic "brick and mortar" composite materials inspired by nacre. The macroscopic strength and ductility (work of fracture) are predicted in terms of the brick properties (size, strength, and layout) and interface cohesive properties (e.g., maximum shear and normal stresses and separations). The results illustrate the trade-off between increasing strength and decreasing ductility with the increasing aspect ratio of the bricks. The models can be used to identify optimum mortar properties that maximize toughness for a given brick strength.

Cohesive zone finite element analysis of crack initiation from a butt joint’s interface corner

DOE PAGES

Reedy, E. D.

2014-09-06

The Cohesive zone (CZ) fracture analysis techniques are used to predict the initiation of crack growth from the interface corner of an adhesively bonded butt joint. In this plane strain analysis, a thin linear elastic adhesive layer is sandwiched between rigid adherends. There is no preexisting crack in the problem analyzed, and the focus is on how the shape of the traction–separation (T–U) relationship affects the predicted joint strength. Unlike the case of a preexisting interfacial crack, the calculated results clearly indicate that the predicted joint strength depends on the shape of the T–U relationship. Most of the calculations usedmore » a rectangular T–U relationship whose shape (aspect ratio) is defined by two parameters: the interfacial strength σ* and the work of separation/unit area Γ. The principal finding of this study is that for a specified adhesive layer thickness, there is any number of σ*, Γ combinations that generate the same predicted joint strength. For each combination there is a corresponding CZ length. We developed an approximate CZ-like elasticity solution to show how such combinations arise and their connection with the CZ length.« less

The Impact of Thermocycling Process on the Dislodgement Force of Different Endodontic Cements

PubMed Central

Saghiri, Mohammad Ali; Asatourian, Armen; Garcia-Godoy, Franklin; Gutmann, James L.; Sheibani, Nader

2013-01-01

To evaluate the effects of thermocycling (500 cycles, 5°C/55°C) on the push-out bond strength of calcium silicate based cements including WMTA, Nano-WMTA, and Bioaggregate to root dentin. Forty-eight dentin slices were prepared and divided into 3 groups (n = 16) and filled with Angelus WMTA, Nano-WMTA, or Bioaggregate. After incubation, half of the samples were thermocycled while the other half remained untreated. Push-out bond strength was calculated, and the modes of the bond failures were determined by SEM. The highest bond strength was seen in nonthermocycled Nano-WMTA samples and the lowest in thermocycled Bioaggregate samples. The significant differences between nonthermocycled and thermocycled samples were only noticed in WMTA and Nano-WMTA groups (P < 0.001). The mode of failure for thermocycled samples of all three cements was mostly cohesive. Thermocycling process can drastically affect the push-out bond strength of calcium silicate based cements. The intrastructural damages occurred due to the thermal stresses, causing cohesive failures in set materials. Sealing property of endodontic cements which have experienced the thermal stresses can be jeopardized due to occlusal forces happening in furcation cites. PMID:24063004

The Effects of Substrate Material and Thermal Processing Atmosphere on the Strength of PS304: A High Temperature Solid Lubricant Coating

NASA Technical Reports Server (NTRS)

DellaCorte, Christopher

2002-01-01

PS304, a plasma spray deposited solid lubricant coating developed for high temperature sliding contacts was deposited on nine different substrate metals, heat treated at 650C in either air or argon and subsequently tested for strength using a commercially available pull-off adhesion test. Some samples were examined metallographically to help elucidate and explain the results. As deposited coatings exhibit pull-off strengths typically between 16 and 20 MPa with failure occuring (cohesively) within the coating. Heat treatment in argon at 650 C results in a slight increase in coating (cohesive) strength of about 30 percent to 21 to 27 MPa. Heat treatment in air at 650 C results in a dramatic increase in strength to over 30 MPa, exceeding the strength of the epoxy used in the pull test. Cross section metallographic analyses show that no microstructural coating changes occur following the argon heat treatments, however, exposure to air at 650C gives rise to the formation of a second chromium-rich phase precipitate within the PS304 NiCr constituent which provides a strengthening effect and a slight (approximately 5 percent) coating thickness increase. Subsequent heat treatments do not result in any further coating changes. Based upon these studies, PS304 is a suitable coating for use on a wide variety of high temperature substrates and must be heat treated following deposition to enhance strength and ensure dimensional stability.

Performance of universal adhesives on bonding to leucite-reinforced ceramic.

PubMed

Kim, Ryan Jin-Young; Woo, Jung-Soo; Lee, In-Bog; Yi, Young-Ah; Hwang, Ji-Yun; Seo, Deog-Gyu

2015-01-01

This study aimed to investigate the microshear bond strength of universal bonding adhesives to leucite-reinforced glass-ceramic. Leucite-reinforced glass-ceramic blocks were polished and etched with 9.5% hydrofluoric acid for 1 min. The specimens were assigned to one of four groups based on their surface conditioning (n = 16): 1) NC: negative control with no further treatment; 2) SBU: Single Bond Universal (3M ESPE); 3) ABU: ALL-BOND Universal (Bisco); and 4) PC: RelyX Ceramic Primer and Adper Scotchbond Multi-Purpose Adhesive (3M ESPE) as a positive control. RelyX Ultimate resin cement (3M ESPE) was placed on the pretreated ceramic and was light cured. Eight specimens from each group were stored in water for 24 h, and the remaining eight specimens were thermocycled 10,000 times prior to microshear bond strength evaluation. The fractured surfaces were examined by stereomicroscopy and scanning electron microscopy (SEM). After water storage and thermocycling, the microshear bond strength values decreased in the order of PC > SBU and ABU > NC (P < 0.05). Thermocycling significantly reduced the microshear bond strength, regardless of the surface conditioning used (P < 0.05). Cohesive failure in the ceramic and mixed failure in the ceramic and resin cement were observed in the fractured specimens. The percentage of specimens with cohesive failure after 24 h of water storage was: NC (50%), SBU (75%), ABU (75%), and PC (87%). After thermocycling, the percentage of cohesive failure in NC decreased to 25%; however, yet the percentages of the other groups remained the same. Although the bond strength between resin and hydrofluoric acid-etched glass ceramic was improved when universal adhesives were used, conventional surface conditioning using a separate silane and adhesive is preferable to a simplified procedure that uses only a universal adhesive for cementation of leucite-reinforced glass-ceramic.

Shear strength characteristics of mechanically biologically treated municipal solid waste (MBT-MSW) from Bangalore.

PubMed

Sivakumar Babu, G L; Lakshmikanthan, P; Santhosh, L G

2015-05-01

Strength and stiffness properties of municipal solid waste (MSW) are important in landfill design. This paper presents the results of comprehensive testing of shear strength properties of mechanically biologically treated municipal solid waste (MBT-MSW) in laboratory. Changes in shear strength of MSW as a function of unit weight and particle size were investigated by performing laboratory studies on the MSW collected from Mavallipura landfill site in Bangalore. Direct shear tests, small scale and large scale consolidated undrained and drained triaxial tests were conducted on reconstituted compost reject MSW samples. The triaxial test results showed that the MSW samples exhibited a strain-hardening behaviour and the strength of MSW increased with increase in unit weight. Consolidated drained tests showed that the mobilized shear strength of the MSW increased by 40% for a unit weight increase from 7.3kN/m(3) to 10.3kN/m(3) at 20% strain levels. The mobilized cohesion and friction angle ranged from 5 to 9kPa and 8° to 33° corresponding to a strain level of 20%. The consolidated undrained tests exhibited reduced friction angle values compared to the consolidated drained tests. The friction angle increased with increase in the unit weight from 8° to 55° in the consolidated undrained tests. Minor variations were found in the cohesion values. Relationships for strength and stiffness of MSW in terms of strength and stiffness ratios are developed and discussed. The stiffness ratio and the strength ratio of MSW were found to be 10 and 0.43. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of denture cleansing agents on tensile and shear bond strengths of soft liners to acrylic denture base.

PubMed

Mahboub, Farhang; Salehsaber, Fariba; Parnia, Fereydoon; Gharekhani, Vahedeh; Kananizadeh, Yousef; Taghizadeh, Mahsa

2017-01-01

Background. The aim of the present study was to evaluate the effect of Corega and 2.5% sodium hypochlorite cleansing agents on the shear and tensile bond strengths of GC soft liner to denture base. Methods. A total of 144 samples (72 samples for tensile and 72 for shear bond strength evaluations) were prepared. The samples in each group were subdivided into three subgroups in terms of the cleansing agent used (2.5% sodium hypochlorite, Corega and distilled water [control group]). All the samples were stored in distilled water, during which each sample was immersed for 15 minutes daily in sodium hypochlorite or Corega solutions. After 20 days the tensile and shear bond strengths were determined using a universal testing machine. In addition, a stereomicroscope was used to evaluate fracture modes. Data were analyzed with one-way ANOVA, using SPSS 16. Results. The results of post hoc Tukey tests showed significant differences in the mean tensile and shear bond strength values between the sodium hypochlorite group with Corega and control groups (P=0.001 for comparison of tensile bond strengths between the sodium hypochlorite and control groups, and P<0.001 for the comparison of tensile bond strengths between the sodium hypochlorite and Corega groups and the shear bond strengths between the sodium hypochlorite and Corega groups, and sodium hypochlorite and control groups).The majority of failures were cohesive in the control and Corega groups and cohesive/adhesive in the sodium hypochlorite group. Conclusion. Immersion of soft liners in Corega will result in longevity of soft liners compared to immersion in sodium hypochlorite solution and sodium hypochlorite solution significantly decreased the tensile and shear bond strengths compared to the control and Corega groups.

Effect of denture cleansing agents on tensile and shear bond strengths of soft liners to acrylic denture base

PubMed Central

Mahboub, Farhang; Salehsaber, Fariba; Parnia, Fereydoon; Gharekhani, Vahedeh; Kananizadeh, Yousef; Taghizadeh, Mahsa

2017-01-01

Background. The aim of the present study was to evaluate the effect of Corega and 2.5% sodium hypochlorite cleansing agents on the shear and tensile bond strengths of GC soft liner to denture base. Methods. A total of 144 samples (72 samples for tensile and 72 for shear bond strength evaluations) were prepared. The samples in each group were subdivided into three subgroups in terms of the cleansing agent used (2.5% sodium hypochlorite, Corega and distilled water [control group]). All the samples were stored in distilled water, during which each sample was immersed for 15 minutes daily in sodium hypochlorite or Corega solutions. After 20 days the tensile and shear bond strengths were determined using a universal testing machine. In addition, a stereomicroscope was used to evaluate fracture modes. Data were analyzed with one-way ANOVA, using SPSS 16. Results. The results of post hoc Tukey tests showed significant differences in the mean tensile and shear bond strength values between the sodium hypochlorite group with Corega and control groups (P=0.001 for comparison of tensile bond strengths between the sodium hypochlorite and control groups, and P<0.001 for the comparison of tensile bond strengths between the sodium hypochlorite and Corega groups and the shear bond strengths between the sodium hypochlorite and Corega groups, and sodium hypochlorite and control groups).The majority of failures were cohesive in the control and Corega groups and cohesive/adhesive in the sodium hypochlorite group. Conclusion. Immersion of soft liners in Corega will result in longevity of soft liners compared to immersion in sodium hypochlorite solution and sodium hypochlorite solution significantly decreased the tensile and shear bond strengths compared to the control and Corega groups. PMID:29184635

STRESS AND FAILURE ANALYSIS OF RAPIDLY ROTATING ASTEROID (29075) 1950 DA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirabayashi, Masatoshi; Scheeres, Daniel J., E-mail: masatoshi.hirabayashi@colorado.edu

Rozitis et al. recently reported that near-Earth asteroid (29075) 1950 DA, whose bulk density ranges from 1.0 g cm{sup –3} to 2.4 g cm{sup –3}, is a rubble pile and requires a cohesive strength of at least 44-76 Pa to keep from failing due to its fast spin period. Since their technique for giving failure conditions required the averaged stress over the whole volume, it discarded information about the asteroid's failure mode and internal stress condition. This paper develops a finite element model and revisits the stress and failure analysis of 1950 DA. For the modeling, we do not consider material hardening andmore » softening. Under the assumption of an associated flow rule and uniform material distribution, we identify the deformation process of 1950 DA when its constant cohesion reaches the lowest value that keeps its current shape. The results show that to avoid structural failure the internal core requires a cohesive strength of at least 75-85 Pa. It suggests that for the failure mode of this body, the internal core first fails structurally, followed by the surface region. This implies that if cohesion is constant over the whole volume, the equatorial ridge of 1950 DA results from a material flow going outward along the equatorial plane in the internal core, but not from a landslide as has been hypothesized. This has additional implications for the likely density of the interior of the body.« less

Influence of cross-linkers on the cohesive and adhesive self-healing ability of polysulfide-based thermosets.

PubMed

Lafont, U; van Zeijl, H; van der Zwaag, S

2012-11-01

Synthetic systems with intrinsic self-repairing or self-healing abilities have emerged during the past decade. In this work, the influence of the cross-linker and chain rigidity on the healing ability of thermoset rubbers containing disulfide bonds have been investigated. The produced materials exhibit adhesive and cohesive self-healing properties. The recovery of these two functionalities upon the thermally triggered healing events has shown to be highly dependent on the network cross-link density and chain rigidity. As a result, depending on the rubber thermoset intrinsic physical properties, the thermal mending leading to full cohesive recovery can be achieved in 20-300 min at a modest healing temperature of 65 °C. The adhesive strength ranges from 0.2 to 0.5 MPa and is fully recovered even after multiple failure events.

Geotechnical Implications for the use of Alfalfa in Experimental Studies of Alluvial-Channel Morphology and Planform

NASA Astrophysics Data System (ADS)

Pollen, N.; Simon, A.

2006-12-01

Research on the interactions between vegetation and channel flow dynamics has shown that vegetation is an important control on river morphology and planform. Increased vegetation density is commonly linked to a decrease in bank erosion and lateral migration rates. Roots add to bank strength through the production of a reinforced soil-root matrix, and vegetation can also act to increase bank stability through its hydrological effects, including canopy interception, and removal of soil water through evapotranspiration. Flow dynamics are also affected by vegetation, with a number of studies showing a linkage between vegetation density and width- depth-velocity relations and bank roughness. To evaluate the effects of vegetation on channel morphology and planform, several experimental studies in flumes have used alfalfa sprouts (Medicago sativa) to seed the bed and banks of experimental channels. In such studies, the effects of vegetation are accounted for by qualitatively increasing the resistance of the bank material to lateral erosion. However, the material properties of alfalfa roots and stems, and the actual increase in resistance provided to the banks under different densities of alfalfa have thus far been ignored. To quantify this added erosion resistance, alfalfa sprouts were grown for 7 to 21 days, in sand with a d50 of 0.23 mm. At regular intervals, roots and stems were tested to measure tensile strength and forces required for pullout. Results of the tensile-strength measurements display the typical non-linear decrease of tensile strength (in MPa) with increasing root diameter but the curve is shifted to the left (weaker for a given diameter) of other riparian species. However, to calculate the increase in bank cohesion due to alfalfa roots, it is necessary to also account for the number of roots, and the distribution of different root diameters. The number of roots was calculated for a range of stem densities (0 to 10 stems/cm2), assuming a single, un-branching root per stem. Values for the additional cohesion provided by the alfalfa roots were calculated using the root- reinforcement model, RipRoot, producing values of 0 to 11.8 kPa. These results provide a means of quantifying the additional bank resistance provided to experimental channels under different stem/root densities. Cohesion values obtained in this way were successfully related to studies of braiding intensity published by others. The geometric properties of alfalfa scale up from experiments in flumes to approximate young trees on a floodplain. However, soil properties such as cohesion cannot be scaled. As such, the cohesion values due to roots calculated here represent the actual magnitude of reinforcement provided, rather than a scaled value.

Root reinforcement and its contribution to slope stability in the Western Ghats of Kerala, India

NASA Astrophysics Data System (ADS)

Lukose Kuriakose, Sekhar; van Beek, L. P. H.

2010-05-01

The Western Ghats of Kerala, India is prone to shallow landslides and consequent debris flows. An earlier study (Kuriakose et al., DOI:10.1002/esp.1794) with limited data had already demonstrated the possible effects of vegetation on slope hydrology and stability. Spatially distributed root cohesion is one of the most important data necessary to assess the effects of anthropogenic disturbances on the probability of shallow landslide initiation, results of which are reported in sessions GM6.1 and HS13.13/NH3.16. Thus it is necessary to the know the upper limits of reinforcement that the roots are able to provide and its spatial and vertical distribution in such an anthropogenically intervened terrain. Root tensile strength and root pull out tests were conducted on nine species of plants that are commonly found in the region. They are 1) Rubber (Hevea Brasiliensis), 2) Coconut Palm (Cocos nucifera), 3) Jackfruit trees (Artocarpus heterophyllus), 4) Teak (Tectona grandis), 5) Mango trees (Mangifera indica), 6) Lemon grass (Cymbopogon citratus), 7) Gambooge (Garcinia gummi-gutta), 8) Coffee (Coffea Arabica) and 9) Tea (Camellia sinensis). About 1500 samples were collected of which only 380 could be tested (in the laboratory) due to breakage of roots during the tests. In the successful tests roots failed in tension. Roots having diameters between 2 mm and 12 mm were tested. Each sample tested had a length of 15 cm. Root pull out tests were conducted in the field. Root tensile strength vs root diameter, root pull out strength vs diameter, root diameter vs root depth and root count vs root depth relationships were derived. Root cohesion was computed for nine most dominant plants in the region using the perpendicular root model of Wu et al. (1979) modified by Schimidt et al. (2001). A soil depth map was derived using regression kriging as suggested by Kuriakose et al., (doi:10.1016/j.catena.2009.05.005) and used along with the land use map of 2008 to distribute the computed root tensile strength both vertically and spatially. Root cohesion varies significantly with the type of land use and the depth of soil. The computation showed that a maximum root reinforcement of 40 kPa was available in the first 30 cm of soil while exponentially decreased with depth to just about 3 kPa at 3 m depth. Mixed crops land use unit had the maximum root cohesion while fallow land, degraded forest and young rubber plantation had the lowest root reinforcement. These are the upper limits of root reinforcement that the vegetation can provide. When the soil is saturated, the bond between soil and roots reduces and thus the applicable root reinforcement is limited by the root pullout strength. Root reinforcement estimated from pullout strength vs diameter relationships was significantly lower than those estimated from tensile strength vs diameter relationships.

Saltmarsh creek bank stability: Biostabilisation and consolidation with depth

NASA Astrophysics Data System (ADS)

Chen, Y.; Thompson, C. E. L.; Collins, M. B.

2012-03-01

The stability of cohesive sediments of a saltmarsh in Southern England was measured in the field and the laboratory using a Cohesive Strength Meter (CSM) and a shear vane apparatus. Cores and sediment samples were collected from two tidal creek banks, covered by Atriplex portulacoides (Sea Purslane) and Juncus maritimus (Sea Rush), respectively. The objectives of the study were to examine the variation of sediment stability throughout banks with cantilevers present and investigate the influence of roots and downcore consolidation on bank stability. Data on erosion threshold and shear strength were interpreted with reference to bank depth, sediment properties and biological influences. The higher average erosion threshold was from the Sea Purslane bank whilst the Sea Rush bank showed higher average vane shear strength. The vertical variation in core sediment stability was mainly affected by roots and downcore consolidation with depth. The data obtained from the bank faces revealed that vertical variations in both erosion threshold and vane shear strength were affected primarily by roots and algae. A quantitative estimate of the relative contributions of roots and downcore consolidation to bank sediment stability was undertaken using the bank stability data and sediment density data. This showed that roots contributed more to the Sea Purslane bank stability than downcore consolidation, whilst downcore consolidation has more pronounced effects on the Sea Rush bank stability.

Repair bond strength of nanohybrid composite resins with a universal adhesive

PubMed Central

Altinci, Pinar; Mutluay, Murat; Tezvergil-Mutluay, Arzu

2018-01-01

Abstract Objective: To investigate the repair bond strength of fresh and aged nanohybrid and hybrid composite resins using a universal adhesive (UA). Materials and methods: Fresh and aged substrates were prepared using two nanohybrid (Venus Pearl, Heraus Kulzer; Filtek Supreme XTE, 3 M ESPE) and one hybrid (Z100, 3 M ESPE) composite resin, and randomly assigned to different surface treatments: (1) no treatment (control), (2) surface roughening with 320-grit (SR), (3) SR + UA (iBOND, Heraus Kulzer), (4) SR + Silane (Signum, Ceramic Bond I, Heraeus Kulzer) + UA, (5) SR + Sandblasting (CoJet, 3 M ESPE) + Silane + UA. After surface treatment, fresh composite resin was added to the substrates at 2 mm layer increments to a height of 5 mm, and light cured. Restored specimens were water-stored for 24 h and sectioned to obtain 1.0 × 1.0 mm beams (n = 12), and were either water-stored for 24 h at 37 °C, or water-stored for 24 h, and then thermocycled for 6000 cycles before microtensile bond strength (µTBS) testing. Data were analyzed with ANOVA and Tukey’s HSD tests (p = .05). Results: Combined treatment of SR, sandblasting, silane and UA provided repair bond strength values comparable to the cohesive strength of each tested resin material (p < .05). Thermocycling significantly reduced the cohesive strength of the composite resins upto 65% (p < .05). Repair bond strengths of UA-treated groups were more stable under thermocycling. Conclusions: Universal adhesive application is a reliable method for composite repair. Sandblasting and silane application slightly increases the repair strength for all substrate types. PMID:29250576

Effect of an Extra Hydrophobic Resin Layer on Repair Shear Bond Strength of a Silorane-Based Composite Resin

PubMed Central

Mohammadi, Narmin; Bahari, Mahmoud; Kimyai, Soodabeh; Rahbani Nobar, Behnam

2015-01-01

Objectives: Composite repair is a minimally invasive and conservative approach. This study aimed to evaluate the effect of an additional hydrophobic resin layer on the repair shear bond strength of a silorane-based composite repaired with silorane or methacrylate-based composite. Materials and Methods: Sixty bar-shaped composite blocks were fabricated and stored in saline for 72 hours. The surface of the samples were roughened by diamond burs and etched with phosphoric acid; then, they were randomly divided into three groups according to the repairing process: Group 1: Silorane composite-silorane bonding agent-silorane composite; group 2: Silorane composite-silorane bonding agent-hydrophobic resin-silorane composite, and group 3: Silorane composite-silorane bonding agent-hydrophobic resin methacrylate-based composite. Repairing composite blocks measured 2.5×2.5×5mm. After repairing, the samples were stored in saline for 24 hours and thermocycled for 1500 cycles. The repair bond strength was measured at a strain rate of 1mm/min. Twenty additional cylindrical composite blocks (diameter: 2.5mm, height: 6mm) were also fabricated for measuring the cohesive strength of silorane-based composite. The data were analyzed using One-way ANOVA and the post hoc Tukey’s test (α=0.05). Results: Cohesive bond strength of silorane composite was significantly higher than the repair bond strengths in other groups (P<0.001). The repair bond strength of group 3 was significantly higher than that of group 1 (P=0.001). Conclusion: Application of an additional hydrophobic resin layer for repair of silorane-based composite with a methacrylate-based composite enhanced the repair shear bond strength. PMID:27559348

Repair bond strength of nanohybrid composite resins with a universal adhesive.

PubMed

Altinci, Pinar; Mutluay, Murat; Tezvergil-Mutluay, Arzu

2018-01-01

Objective: To investigate the repair bond strength of fresh and aged nanohybrid and hybrid composite resins using a universal adhesive (UA). Materials and methods: Fresh and aged substrates were prepared using two nanohybrid (Venus Pearl, Heraus Kulzer; Filtek Supreme XTE, 3 M ESPE) and one hybrid (Z100, 3 M ESPE) composite resin, and randomly assigned to different surface treatments: (1) no treatment (control), (2) surface roughening with 320-grit (SR), (3) SR + UA (iBOND, Heraus Kulzer), (4) SR + Silane (Signum, Ceramic Bond I, Heraeus Kulzer) + UA, (5) SR + Sandblasting (CoJet, 3 M ESPE) + Silane + UA. After surface treatment, fresh composite resin was added to the substrates at 2 mm layer increments to a height of 5 mm, and light cured. Restored specimens were water-stored for 24 h and sectioned to obtain 1.0 × 1.0 mm beams ( n  = 12), and were either water-stored for 24 h at 37 °C, or water-stored for 24 h, and then thermocycled for 6000 cycles before microtensile bond strength (µTBS) testing. Data were analyzed with ANOVA and Tukey's HSD tests ( p  = .05). Results: Combined treatment of SR, sandblasting, silane and UA provided repair bond strength values comparable to the cohesive strength of each tested resin material ( p  < .05). Thermocycling significantly reduced the cohesive strength of the composite resins upto 65% ( p  < .05). Repair bond strengths of UA-treated groups were more stable under thermocycling. Conclusions: Universal adhesive application is a reliable method for composite repair. Sandblasting and silane application slightly increases the repair strength for all substrate types.

Ice/water slurry blocking phenomenon at a tube orifice.

PubMed

Hirochi, Takero; Yamada, Shuichi; Shintate, Tuyoshi; Shirakashi, Masataka

2002-10-01

The phenomenon of ice-particle/water mixture blocking flow through a pipeline is a problem that needs to be solved before mixture flow can be applied for practical use in cold energy transportation in a district cooling system. In this work, the blocking mechanism of ice-particle slurry at a tube orifice is investigated and a criterion for blocking is presented. The cohesive nature of ice particles is shown to cause compressed plug type blocking and the compressive yield stress of a particle cluster is presented as a measure for the cohesion strength of ice particles.

Linking Anger Trait with Somatization in Low-Grade College Students: Moderating Roles of Family Cohesion and Adaptability.

PubMed

Liu, Liang; Liu, Cuilian; Zhao, Xudong

2017-02-25

Between 22% and 58% of patients in primary care settings complain of somatic symptoms. Previous research has found that somatization was associated with anger traits and family functions. However, studies that specifically assess the moderating effect of family function in how anger traits become somatic complaints are lacking. This study was designed to examine whether the variances in family cohesion and family adaptability moderated the strength of the relationship between anger traits and somatization. A cross-section design was conducted and 2008 college students were recruited from a comprehensive university in Shanghai. All participants finished questionnaires including Symptom Check List- 90 (SCL-90), State-Trait Anger Expression Inventory 2 (STAXI-2, Chinese version) and Family Adaptability and Cohesion Scale, second edition (FACES II, Chinese Version) to assess their degree of current somatization, anger trait and family function. Hierarchical linear regression analysis (Enter) was conducted respectively for men and women to examine the moderation effect of family cohesion and family adaptability in the association between anger and somatization. Somatic symptoms were significantly linked in the expected directions with depression and anger trait for both genders. Family cohesion and family adaptability were negatively associated with somatic symptoms. For female college students family cohesion was found to moderate the link between anger trait and somatization, but for male college students the moderation effect of family cohesion was marginally significant. The moderating role of family adaptability was significant for neither male nor female after current depressive symptoms were accounted for. Proneness to anger is an independent predictor of somatization. For women, a high level of family cohesion was a protective factor which could reduce the influence of anger trait on somatic symptoms. Without comorbidity of current depression, family adaptability to some degree exempted individuals with anger proneness from developing somatic complaints. Interventions that integrate family cohesion cultivation, family flexibility fostering and depression treatment might be more effective for somatic patients high in anger trait.

Effectiveness of antistripping additives in the field.

DOT National Transportation Integrated Search

1995-01-01

Stripping has long been recognized as a cause of asphalt pavement damage. Water may get between the asphalt film and the aggregate surface, causing an adhesive failure, or water may combine with the asphalt to affect the cohesive strength of the mate...

Feasibility of Virtual Tablet-Based Group Exercise Among Older Adults in Siberia: Findings From Two Pilot Trials

PubMed Central

2018-01-01

Background Regular physical activity has a positive effect on physical health, well-being, and life satisfaction of older adults. However, engaging in regular physical activity can be challenging for the elderly population because of reduced mobility, low motivation, or lack of the proper infrastructures in their communities. Objective The objective of this paper was to study the feasibility of home-based online group training—under different group cohesion settings—and its effects on adherence and well-being among Russian older adults. We focused particularly on the technology usability and usage and on the adherence to the training (in light of premeasures of social support, enjoyment of physical activity, and leg muscle strength). As a secondary objective, we also explored the effects of the technology-supported intervention on subjective well-being and loneliness. Methods Two pilot trials were carried out exploring two different group cohesion settings (weak cohesion and strong cohesion) in the period from 2015 to 2016 in Tomsk, Russian Federation. A total of 44 older adults (59-83 years) participated in the two pilots and followed a strength and balance training program (Otago) for 8 weeks with the help of a tablet-based virtual gym app. Participants in each pilot were assigned to an interaction condition, representing the online group exercising, and an individual condition, representing a home-based individual training. Both conditions featured persuasion strategies but differed in the ability to socialize and train together. Results Both interaction and individual groups reported a high usability of the technology. Trainees showed a high level of technology acceptance and, particularly, a high score in intention to future use (4.2-5.0 on a 5-point Likert scale). Private texting (short service message [SMS]) was used more than public texting, and the strong cohesion condition resulted in more messages per user. Joint participations to training sessions (copresence) were higher for the social group with higher cohesion. The overall adherence to the training was 74% (SD 27%). Higher levels of social support at baseline were associated with higher adherence in the low cohesion condition (F1,18=5.23, P=.03), whereas in the high cohesion, such association was not found. Overall improvement in the satisfaction with life score was observed between pre and post measures (F1,31=5.85, P=.02), but no decrease in loneliness. Conclusions Online group exercising was proven feasible among healthy independently living older adults in Russia. The pilots suggest that a physical training performed in a virtual environment positively affect the life satisfaction of the trainees, but it does not provide support for a decrease in loneliness. High cohesion groups are preferable for group exercising, especially to mitigate effects of low social support on adherence. Further research in motivating group interactions in training settings is needed. PMID:29487045

Cavitation transition in the energy landscape: Distinct tensile yielding behavior in strongly and weakly attractive systems.

PubMed

Altabet, Y Elia; Fenley, Andreia L; Stillinger, Frank H; Debenedetti, Pablo G

2018-03-21

Particles with cohesive interactions display a tensile instability in the energy landscape at the Sastry density ρ S . The signature of this tensile limit is a minimum in the landscape equation of state, the pressure-density relationship of inherent structures sampled along a liquid isotherm. Our previous work [Y. E. Altabet, F. H. Stillinger, and P. G. Debenedetti, J. Chem. Phys. 145, 211905 (2016)] revisited the phenomenology of Sastry behavior and found that the evolution of the landscape equation of state with system size for particles with interactions typical of molecular liquids indicates the presence of an athermal first-order phase transition between homogeneous and fractured inherent structures, the latter containing several large voids. Here, we study how this tensile limit manifests itself for different interparticle cohesive strengths and identify two distinct regimes. Particles with sufficiently strong cohesion display an athermal first-order phase transition, consistent with our prior characterization. Weak cohesion also displays a tensile instability. However, the landscape equation of state for this regime is independent of system size, suggesting the absence of a first-order phase transition. An analysis of the voids suggests that yielding in the energy landscape of weakly cohesive systems is associated with the emergence of a highly interconnected network of small voids. While strongly cohesive systems transition from exclusively homogeneous to exclusively fractured configurations at ρ S in the thermodynamic limit, this interconnected network develops gradually, starting at ρ S , even at infinite system size.

Cavitation transition in the energy landscape: Distinct tensile yielding behavior in strongly and weakly attractive systems

NASA Astrophysics Data System (ADS)

Altabet, Y. Elia; Fenley, Andreia L.; Stillinger, Frank H.; Debenedetti, Pablo G.

2018-03-01

Particles with cohesive interactions display a tensile instability in the energy landscape at the Sastry density ρS. The signature of this tensile limit is a minimum in the landscape equation of state, the pressure-density relationship of inherent structures sampled along a liquid isotherm. Our previous work [Y. E. Altabet, F. H. Stillinger, and P. G. Debenedetti, J. Chem. Phys. 145, 211905 (2016)] revisited the phenomenology of Sastry behavior and found that the evolution of the landscape equation of state with system size for particles with interactions typical of molecular liquids indicates the presence of an athermal first-order phase transition between homogeneous and fractured inherent structures, the latter containing several large voids. Here, we study how this tensile limit manifests itself for different interparticle cohesive strengths and identify two distinct regimes. Particles with sufficiently strong cohesion display an athermal first-order phase transition, consistent with our prior characterization. Weak cohesion also displays a tensile instability. However, the landscape equation of state for this regime is independent of system size, suggesting the absence of a first-order phase transition. An analysis of the voids suggests that yielding in the energy landscape of weakly cohesive systems is associated with the emergence of a highly interconnected network of small voids. While strongly cohesive systems transition from exclusively homogeneous to exclusively fractured configurations at ρS in the thermodynamic limit, this interconnected network develops gradually, starting at ρS, even at infinite system size.

Eco-geomorphic controls on slope stability

NASA Astrophysics Data System (ADS)

Hales, T.; Ford, C.; Hwang, T.; Vose, J.; Band, L.

2009-04-01

Vegetation controls soil-mantled landscape evolution primarily through growth of roots into soil and rock. Root-soil interactions affect the spatial distribution and rate of shallow landsliding and other hillslope processes. Yet the distribution and tensile strength of roots depends on a number of geomorphically-influenced parameters, including soil moisture. Our field-based study investigated the effects of topography on root distributions, tensile strengths, and cohesion. Systematic differences in plant species distribution and soil properties are found in the hollow-nose topography of soil-mantled landscapes; with hollows containing thick colluvial soils and mesic tree species and noses containing thinner, more differentiated soils and more xeric species. We investigated whether these topographic variations in geomorphic and ecologic properties affected the spatial distribution of root cohesion by measuring the distribution and tensile strength of roots from soil pits dug downslope of fifteen individual trees in the Coweeta Hydrologic Laboratory, North Carolina. Our soil pits were located to capture variance in plant species (10 species total), topographic positions (nose, hollow), and sizes (a range of DBH between 5 cm and 60 cm). Root tensile strengths showed little variance with different species, but showed strong differences as a function of topography, with nose roots stronger than hollow roots. Similarly, within species, root cellulose content was systematically greater in trees on nose positions compared to those in hollows. For all species, roots were concentrated close to the soil surface (at least 70% of biomass occurred within 50 cm of the surface) and variations in this pattern were primarily a function of topographic position. Hollow roots were more evenly distributed in the soil column than those on noses, yet trees located on noses had higher mean root cohesion than those in hollows because of a higher root tensile force. These data provide an empirical basis for the development of simple geomorphic transport laws that explicitly include vegetation.

Measurement of Cohesion in Asteroid Regolith Materials

NASA Technical Reports Server (NTRS)

Kleinhenz, Julie E.; Gaier, James R.; Waters, Deborah L.; Harvey, Ralph; Zeszut, Zoe; Carreno, Brandon; Shober, Patrick

2017-01-01

A study has been initiated to examine cohesive forces in asteroid materials to contribute to a better understanding of low density bodies such as asteroids and Phobos, and assist in exploration missions involving interaction with their surface material. The test specimen used in this study was a lightly weathered CM2 meteorite which is spectroscopically similar to Type C (carbonaceous) asteroids, and thought to have representative surface chemistry. To account for sample heterogeneity, adhesion forces were measured between the CM2 sample and its five primary mineral phase components. These adhesive forces bound the range of cohesive force that can be expected for the bulk material. All materials were characterized using a variety of optical and spectroscopic methods. Adhesive forces on the order of 50 to 400 µN were measured using a torsion balance in an ultrahigh vacuum chamber. The mineral samples exhibited clearly different adhesive strengths in the following hierarchy: Serpentine > Siderite > Bronzite > Olivine ˜ Fe-Ni.

Cohesive Laws and Progressive Damage Analysis of Composite Bonded Joints, a Combined Numerical/Experimental Approach

NASA Technical Reports Server (NTRS)

Girolamo, Donato; Davila, Carlos G.; Leone, Frank A.; Lin, Shih-Yung

2015-01-01

The results of an experimental/numerical campaign aimed to develop progressive damage analysis (PDA) tools for predicting the strength of a composite bonded joint under tensile loads are presented. The PDA is based on continuum damage mechanics (CDM) to account for intralaminar damage, and cohesive laws to account for interlaminar and adhesive damage. The adhesive response is characterized using standard fracture specimens and digital image correlation (DIC). The displacement fields measured by DIC are used to calculate the J-integrals, from which the associated cohesive laws of the structural adhesive can be derived. A finite element model of a sandwich conventional splice joint (CSJ) under tensile loads was developed. The simulations, in agreement with experimental tests, indicate that the model is capable of predicting the interactions of damage modes that lead to the failure of the joint.

Influence of Using Clinical Microscope as Auxiliary to Perform Mechanical Cleaning of Post Space: A Bond Strength Analysis.

PubMed

Ferreira, Ricardo; Prado, Maíra; de Jesus Soares, Adriana; Zaia, Alexandre Augusto; de Souza-Filho, Francisco José

2015-08-01

The aim of the present study was to evaluate the influence of using a clinical microscope while performing mechanical cleaning of post space walls on the bond strength of a fiberglass post to dentin. Forty-five bovine roots were used. After preparation, roots were filled using gutta-percha and Pulp Canal Sealer (SybronEndo, Orange, CA). Subsequently, for post space preparation, the roots were divided into 3 groups: control (only heat condenser + specific bur of the post system); cleaning without a microscope, mechanical cleaning (after the procedure described in the control group, round burs were used to improve cleaning); and cleaning with a microscope, mechanical cleaning performed with round burs visualized under a clinical microscope. Then, fiberglass posts were cemented. The roots were prepared and evaluated by the push-out test. Data were analyzed using Kruskal-Wallis and Student-Newman-Keuls tests (P < .05). The failure pattern was classified as follows: adhesive between the cement and dentin, adhesive dentin/cement/post, mixed cohesive within dentin, mixed cohesive post, and mixed cohesive post/dentin. The bond strength values (mean ± standard deviation) were control (cervical 1.17 ± 1.1, middle 0.40 ± 0.3, apical 0.52 ± 0.3, and total 0.95 ± 1.9), cleaning without a microscope (cervical 1.66 ± 2.3, middle 0.65 ± 1.1, apical 0.79 ± 1.2, and total1.04 ± 1.7), and cleaning with a microscope (cervical 3.26 ± 2.8, middle 1.97 ± 3.5, apical 1.85 ± 4.1, and total 2.37 ± 3.5). In the cleaning with a microscope group, the bond strength values were significantly higher than those in the other groups. In all groups, the main failure pattern was adhesive between cement and dentin. The use of a clinical microscope while performing mechanical cleaning during post space preparation improved the bond strength of a fiberglass post to dentin. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Study of the Peak Shear Strength of a Cement-Filled Hard Rock Joint

NASA Astrophysics Data System (ADS)

She, Cheng-Xue; Sun, Fu-Ting

2018-03-01

The peak shear strength of a cement-filled hard rock joint is studied by theoretical analysis and laboratory testing. Based on the concept of the shear resistance angle, by combining the statistical method and fractal theory, three new parameters are proposed to characterize the three-dimensional joint morphology, reflecting the effects of the average roughness, multi-scale asperities and the dispersion degree of the roughness distribution. These factors are independent of the measurement scale, and they reflect the anisotropy of the joint roughness. Compressive shear tests are conducted on cement-filled joints. Because joints without cement can be considered special cement-filled joints in which the filling degree of cement is zero, they are also tested. The cement-filled granite joint fails primarily along the granite-cement interfaces. The filling degree of cement controls the joint failure and affects its mechanical behaviour. With a decrease in the filling degree of cement, the joint cohesion decreases; however, the dilatancy angle and the basic friction angle of the interface increase. As the filling degree approaches zero, the cohesion approaches zero, while the dilatancy angle and the basic friction angle increase to those of the joint without cement. A set of formulas is proposed to evaluate the peak shear strength of the joints with and without cement. The formulas are shown to be reasonable by comparison with the tested peak shear strength, and they reflect the anisotropy of the strength. This research deepens the understanding of cement-filled joints and provides a method to evaluate their peak shear strength.

Geostability of Didymos, the target of the AIDA mission

NASA Astrophysics Data System (ADS)

Zhang, Yun; Richardson, Derek C.; Barnouin, Olivier; Maurel, Clara; Michel, Patrick; Schwartz, Stephen R.; Ballouz, Ronald; Benner, Lance A. M.; Naidu, Shantanu P.

2016-10-01

As the target of the proposed Asteroid Impact & Deflection Assessment (AIDA) mission [1, 2], the near-Earth binary asteroid 65803 Didymos represents a special class of binary asteroid, those whose primaries are at risk of rotational disruption [3]. To support the AIDA mission and gain a better understanding of these binary systems, we investigate the structural stability and dynamic behavior of the Didymos primary and the orbital stability of the secondary using a Soft-Sphere Discrete Element Method (SSDEM) [4]. The primary and the secondary are modeled as granular assemblies. In the first step of this study, the primary is artificially spun up to the current spin period of 2.26 h using a quasi-static spin-up procedure without considering the secondary [5]. The effects of arrangement and size distribution of constituent particles, bulk density, spin-up path, interparticle friction, and cohesion strength on the dynamic behavior of self-gravitating aggregates are numerically explored. The results show that the strength and stability of a spinning self-gravitating aggregate depend strongly on its internal configuration and material parameters, while its failure mode and mechanism are affected by its internal configuration and the cohesion strength. When cohesion is not included, the Didymos primary rubble-pile model can maintain its shape at the current observed spin rate within the uncertainty of the observed bulk density (< 2.7 g/cc) using material parameters with friction angle of ~30°, which most cohesionless sands can sustain. In the second step, the effect of the secondary on the stability of the primary is studied. The secondary can stably orbit the primary without including cohesion. The results show that the presence of the secondary will slightly reduce the stability of the primary. Our study provides some constraints on the possible physical properties of the Didymos primary.References: [1] Michel et al. 2016, ASR 57, 2529; [2] Cheng et al. 2016, P&SS 127, 27; [3] Olivier et al. 2015, DPS 47; [4] Schwartz et al. 2012, Granul. Matter 14, 363; [5] Zhang et al. 2016, in preparation.

Achieving Multidisciplinary Collaboration for the Creation of a Pulmonary Embolism Response Team: Creating a "Team of Rivals".

PubMed

Kabrhel, Christopher

2017-03-01

Pulmonary embolism response teams (PERTs) have recently been developed to streamline care for patients with life-threatening pulmonary embolism (PE). PERTs are unique among rapid response teams, in that they bring together a multidisciplinary team of specialists to care for a single disease for which there are novel treatments but few comparative data to guide treatment. The PERT model describes a process that includes activation of the team; real-time, multidisciplinary consultation; communication of treatment recommendations; mobilization of resources; and collection of research data. Interventional radiologists, along with cardiologists, emergency physicians, hematologists, pulmonary/critical care physicians, and surgeons, are core members of most PERTs. Bringing together such a wide array of experts leverages the expertise and strengths of each specialty. However, it can also lead to challenges that threaten team cohesion and cooperation. The purpose of this article is to discuss ways to integrate multiple specialists, with diverse perspectives and skills, into a cohesive PERT. The authors will discuss the purpose of forming a PERT, strengths of different PERT specialties, strategies to leverage these strengths to optimize participation and cooperation across team members, as well as unresolved challenges.

Effect of potentially chromogenic beverages on shear bond strength of acrylic denture teeth to heat-polymerized denture base resins

PubMed Central

Neppelenbroek, Karin Hermana; Urban, Vanessa Migliorini; de Oliveira, Denise Gusmão; Porto, Vinícius Carvalho; Almilhatti, Hercules Jorge; Campanha, Nara Hellen

2016-01-01

Background: Detachment of denture acrylic resin artificial teeth from denture base resin is one of the most common problems presented by denture wearers. Purpose: This study investigated the shear bond strength (SBS) and fracture type of bonding interface of two commercial acrylic teeth (Vipi Dent Plus e Biolux) to two denture base resins (Vipi Cril e Lucitone 550) after immersion in potentially chromogenic beverages (coffee, cola soft drink, and red wine) or control solution (distilled water). Materials and Methods: Maxillary central incisor acrylic teeth were placed at 45° to denture base resin and submitted to short polymerization cycle according to manufacturers. Specimens were divided according to the combination tooth/resin/solution (n = 8) and submitted to bond strength tests in a universal testing machine MTS-810 (0.5 mm/min). Subsequently, fracture area was analyzed by stereomicroscope at a magnification of ×10 and categorized into adhesive, cohesive, or mixed failure. Results: The bond strength of teeth/denture base resins interface was not significantly affected by tested solutions (P > 0.087), except for Biolux teeth immersed in coffee (P < 0.01). In all conditions, the Vipi Dent Plus teeth showed higher bond strength to Lucitone and Vipi Cril resins when compared to Biolux teeth (P < 0.003). All specimens’ failure modes were cohesive. Conclusions: The SBS of acrylic teeth to denture base resins was not generally influenced by immersion in the tested staining beverages. PMID:27621547

Numerical Study of Frictional Properties and the Role of Cohesive End-Zones in Large Strike- Slip Earthquakes

NASA Astrophysics Data System (ADS)

Lovely, P. J.; Mutlu, O.; Pollard, D. D.

2007-12-01

Cohesive end-zones (CEZs) are regions of increased frictional strength and/or cohesion near the peripheries of faults that cause slip distributions to taper toward the fault-tip. Laboratory results, field observations, and theoretical models suggest an important role for CEZs in small-scale fractures and faults; however, their role in crustal-scale faulting and associated large earthquakes is less thoroughly understood. We present a numerical study of the potential role of CEZs on slip distributions in large, multi-segmented, strike-slip earthquake ruptures including the 1992 Landers Earthquake (Mw 7.2) and 1999 Hector Mine Earthquake (Mw 7.1). Displacement discontinuity is calculated using a quasi-static, 2D plane-strain boundary element (BEM) code for a homogeneous, isotropic, linear-elastic material. Friction is implemented by enforcing principles of complementarity. Model results with and without CEZs are compared with slip distributions measured by combined inversion of geodetic, strong ground motion, and teleseismic data. Stepwise and linear distributions of increasing frictional strength within CEZs are considered. The incorporation of CEZs in our model enables an improved match to slip distributions measured by inversion, suggesting that CEZs play a role in governing slip in large, strike-slip earthquakes. Additionally, we present a parametric study highlighting the very great sensitivity of modeled slip magnitude to small variations of the coefficient of friction. This result suggests that, provided a sufficiently well-constrained stress tensor and elastic moduli for the surrounding rock, relatively simple models could provide precise estimates of the magnitude of frictional strength. These results are verified by comparison with geometrically comparable finite element (FEM) models using the commercial code ABAQUS. In FEM models, friction is implemented by use of both Lagrange multipliers and penalty methods.

Cohesion, granular solids, granular liquids, and their connection to small near-Earth objects

NASA Astrophysics Data System (ADS)

Sánchez, P.; Scheeres, D.

2014-07-01

During the last 15 years or so, the Planetary Sciences community has been using Discrete Element Method (DEM) simulation codes to study small near-Earth objects (NEOs). In general, these codes treat gravitational aggregates as conglomerates of spherical particles; a good approximation given that many asteroids are self-gravitating granular media. Unfortunately, the degree of sophistication of these codes, and our own understanding, has not been high enough as to appropriately represent realistic physical properties of granular matter. In particular, angles of friction (θ) and cohesive strength (σ_c) of the aggregates were rarely taken in consideration and this could have led to unrealistic dynamics, and therefore, unrealistic conclusions about the dynamical evolution of small NEOs. In our research, we explore the failure mechanics of spherical (r=71 m) and ellipsoidal (r_1=92 m) self-gravitating aggregates with different angles of friction and values for their cohesive strength, in order to better understand the geophysics of rubble-pile asteroids. In particular we focused on the deformation and different disruption modes provoked by an always increasing angular velocity (spin rate). Scaling arguments allow us to regard simulations with the same aggregate size and different σ_c as equivalent to simulations of aggregates of different size and the same σ_c. We use a computational code that implements a Soft-Sphere DEM. The aggregates are composed by 3,000 spherical solid spheres (7--10 m) with 6 degrees of freedom. The code calculates normal, as well as, frictional (tangential) contact forces by means of soft potentials and the aggregate as a whole mimics the effect of non- spherical particles through the implementation of rolling friction. Cohesive forces, and a cohesive stress, are calculated as the net effect of the sum of the van der Waals forces between the smaller regolith, sand and dust (powder) that are present in real asteroids [1]. These finer materials form a matrix of sorts that holds the bigger boulders together. The aggregates were slowly spun up to disruption controlling for angle of friction, cohesion and global shape. Systems with no frictional forces had θ≈ 12° and are in effect granular liquids in the best case scenario. Systems with only surface-surface friction had θ≈ 25°, which is typical in laboratory experiments with spherical glass beads. Systems that also implemented rolling friction had θ≈ 35°, which is typical of non-cohesive granular media on the Earth. How much each aggregate deformed before disruption was directly related to the angle of friction. The greater θ allowed for much less deformation before disruption. Cohesive forces on the other hand controlled the mode of disruption and maximum spin rate and showed that the change from shedding to fission is continuous and therefore, they should not be seen as different disruption processes. The figure shows the deformation and disruption of three initially spherical aggregates (left) and three initially ellipsoidal aggregates (right) with increasing cohesive strength from left to right (θ≈ 35°). Through scaling arguments we could also see these aggregates as having the exact same σ_c=25 Pa but different sizes. If we do that, the aggregates measure about 1.6 km, 5 km, and 22 km, and the particles, or groups of particles being detached now have similar sizes. This has now become a problem of resolution, i.e., the number and size of particles used in a simulation. These results start to raise fundamental questions regarding the difference between shedding and fission. Is it shedding when it is dust grain by dust grain ejection from the main body or when it is in groups of 10, 100, or 100,000 dust particles? Is it fission when a 1-m piece of the asteroid detaches or when it splits in the middle? Which values of θ and σ_c are realistic? These and other questions will be explored.

Evaluation of interaction properties of geosynthetics in cohesive soils : lab and field pullout tests.

DOT National Transportation Integrated Search

2004-01-01

The considerable increase of using geosynthetics in mechanically stabilized earth (MSE) walls has raised the need to evaluate their interface shear strength and pullout properties in various types of backfills. This report investigates the use of a m...

Family strengths, motivation, and resources as predictors of health promotion behavior in single-parent and two-parent families.

PubMed

Ford-Gilboe, M

1997-06-01

The extent to which selected aspects of family health potential (strengths, motivation, and resources) predicted health work (health-related problem-solving and goal attainment behaviors) was examined in a Canadian sample of 138 female-headed single-parent families and two-parent families. The mother and one child (age 10-14) each completed mailed self-report instruments to assess the independent variables of family cohesion, family pride, mother's non-traditional sex role orientation, general self-efficacy, internal health locus of control, network support, community support, and family income, as well as the dependent variable, health work. With the effects of mothers' education held constant, the independent variables predicted 22 to 27% of the variance in health work in the total sample and each family type. Family cohesion was the most consistent predictor of health work, accounting for 8 to 13% of the variance. The findings challenge existing problem-oriented views of single-parent families by focusing on their potential to engage in health promotion behavior.

Stress transfer and matrix-cohesive fracture mechanism in microfibrillated cellulose-gelatin nanocomposite films.

PubMed

Quero, Franck; Padilla, Cristina; Campos, Vanessa; Luengo, Jorge; Caballero, Leonardo; Melo, Francisco; Li, Qiang; Eichhorn, Stephen J; Enrione, Javier

2018-09-01

Microfibrillated cellulose (MFC) obtained from eucalyptus was embedded in gelatin from two sources; namely bovine and salmon gelatin. Raman spectroscopy revealed that stress is transferred more efficiently from bovine gelatin to the MFC when compared to salmon gelatin. Young's modulus, tensile strength, strain at failure and work of fracture of the nanocomposite films were improved by ∼67, 131, 43 y 243% respectively when using salmon gelatin as matrix material instead of bovine gelatin. Imaging of the tensile fracture surface of the MFC-gelatin nanocomposites revealed that crack formation occurs predominantly within bovine and salmon gelatin matrices rather than within the MFC or at the MFC/gelatin interface. This suggests that the mechanical failure mechanism in these nanocomposite materials is predominantly governed by a matrix-cohesive fracture mechanism. Both strength and flexibility are desirable properties for composite coatings made from gelatin-based materials, and so the findings of this study could assist in their utilization in the food and pharmaceutical industry. Copyright © 2018 Elsevier Ltd. All rights reserved.

Redbank and Fancher Creeks, California: General Design Memorandum

DTIC Science & Technology

1986-02-01

agricultural areas not adjacent to mainstream channels. The runoff for these areas, which are downstream of the Enterprise Canal, was assumed to be zero ...for Dry Creek near Lemon Cove. The skews were negative for all the shorter durations and approached a skew of zero for the Dry Creek at Academy and...potentially non-conservative. However, since the cohesion intercept for the design "R" strength was set equal to zero , the impervious fill design strength

Effect of induced cohesion on stick-slip dynamics in weakly saturated, sheared granular fault gouge

DOE PAGES

Dorostkar, Omid; Guyer, Robert A.; Johnson, Paul Allan; ...

2018-02-28

We use three-dimensional discrete element calculations to study stick-slip dynamics in a weakly wet granular layer designed to simulate fault gouge. The granular gouge is constituted by 8000 spherical particles with a poly-disperse size distribution. At very low liquid content, liquids impose cohesive and viscous forces on particles. Our simulations show that by increasing the liquid content, friction increases and granular layer shows higher recurrence time between slip events. We also observe that slip events exhibit larger friction drop and layer compaction in wet system compared to dry. We demonstrate that a small volume of liquid induces cohesive forces betweenmore » wet particles that are responsible for an increase in coordination number leading to a more stable arrangement of particles. This stabilization is evidenced with two orders of magnitude lower particle kinetic energy in wet system during stick phase. Similar to previous experimental studies, we observe enhanced frictional strength for wet granular layers. In experiments, the physicochemical processes are believed to be the main reason for such behavior, we show however, that at low confining stresses the hydromechanical effects of induced cohesion are sufficient for observed behavior. Our simulations illuminate the role of particle interactions and demonstrate the conditions under which induced cohesion plays a significant role in fault zone processes, including slip initiation, weakening, and failure.« less

Elevated intracellular pH appears in aged oocytes and causes oocyte aneuploidy associated with the loss of cohesion in mice

PubMed Central

Cheng, Jin-Mei; Li, Jian; Tang, Ji-Xin; Chen, Su-Ren; Deng, Shou-Long; Jin, Cheng; Zhang, Yan; Wang, Xiu-Xia; Zhou, Chen-Xi; Liu, Yi-Xun

2016-01-01

ABSTRACT Increases in the aneuploidy rate caused by the deterioration of cohesion with increasing maternal age have been well documented. However, the molecular mechanism for the loss of cohesion in aged oocytes remains unknown. In this study, we found that intracellular pH (pHi) was elevated in aged oocytes, which might disturb the structure of the cohesin ring to induce aneuploidy. We observed for the first time that full-grown germinal vesicle (GV) oocytes displayed an increase in pHi with advancing age in CD1 mice. Furthermore, during the in vitro oocyte maturation process, the pHi was maintained at a high level, up to ∼7.6, in 12-month-old mice. Normal pHi is necessary to maintain protein localization and function. Thus, we put forward a hypothesis that the elevated oocyte pHi might be related to the loss of cohesion and the increased aneuploidy in aged mice. Through the in vitro alkalinization treatment of young oocytes, we observed that the increased pHi caused an increase in the aneuploidy rate and the sister inter-kinetochore (iKT) distance associated with the strength of cohesion and caused a decline in the cohesin subunit SMC3 protein level. Young oocytes with elevated pHi exhibited substantially the increase in chromosome misalignment. PMID:27472084

Effect of induced cohesion on stick-slip dynamics in weakly saturated, sheared granular fault gouge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorostkar, Omid; Guyer, Robert A.; Johnson, Paul Allan

We use three-dimensional discrete element calculations to study stick-slip dynamics in a weakly wet granular layer designed to simulate fault gouge. The granular gouge is constituted by 8000 spherical particles with a poly-disperse size distribution. At very low liquid content, liquids impose cohesive and viscous forces on particles. Our simulations show that by increasing the liquid content, friction increases and granular layer shows higher recurrence time between slip events. We also observe that slip events exhibit larger friction drop and layer compaction in wet system compared to dry. We demonstrate that a small volume of liquid induces cohesive forces betweenmore » wet particles that are responsible for an increase in coordination number leading to a more stable arrangement of particles. This stabilization is evidenced with two orders of magnitude lower particle kinetic energy in wet system during stick phase. Similar to previous experimental studies, we observe enhanced frictional strength for wet granular layers. In experiments, the physicochemical processes are believed to be the main reason for such behavior, we show however, that at low confining stresses the hydromechanical effects of induced cohesion are sufficient for observed behavior. Our simulations illuminate the role of particle interactions and demonstrate the conditions under which induced cohesion plays a significant role in fault zone processes, including slip initiation, weakening, and failure.« less

Cohesion-Induced Stabilization in Stick-Slip Dynamics of Weakly Wet, Sheared Granular Fault Gouge

NASA Astrophysics Data System (ADS)

Dorostkar, Omid; Guyer, Robert A.; Johnson, Paul A.; Marone, Chris; Carmeliet, Jan

2018-03-01

We use three-dimensional discrete element calculations to study stick-slip dynamics in a weakly wet granular layer designed to simulate fault gouge. The granular gouge is constituted by 8,000 spherical particles with a polydisperse size distribution. At very low liquid content, liquids impose cohesive and viscous forces on particles. Our simulations show that by increasing the liquid content, friction increases and granular layer shows higher recurrence time between slip events. We also observe that slip events exhibit larger friction drop and layer compaction in wet system compared to dry. We demonstrate that a small volume of liquid induces cohesive forces between wet particles that are responsible for an increase in coordination number leading to a more stable arrangement of particles. This stabilization is evidenced with 2 orders of magnitude lower particle kinetic energy in wet system during stick phase. Similar to previous experimental studies, we observe enhanced frictional strength for wet granular layers. In experiments, the physicochemical processes are believed to be the main reason for such behavior; we show, however, that at low confining stresses, the hydromechanical effects of induced cohesion are sufficient for observed behavior. Our simulations illuminate the role of particle interactions and demonstrate the conditions under which induced cohesion plays a significant role in fault zone processes, including slip initiation, weakening, and failure.

Linking Anger Trait with Somatization in Low-Grade College Students: Moderating Roles of Family Cohesion and Adaptability

PubMed Central

LIU, Liang; LIU, Cuilian; ZHAO, Xudong

2017-01-01

Background Between 22% and 58% of patients in primary care settings complain of somatic symptoms. Previous research has found that somatization was associated with anger traits and family functions. However, studies that specifically assess the moderating effect of family function in how anger traits become somatic complaints are lacking. Aim This study was designed to examine whether the variances in family cohesion and family adaptability moderated the strength of the relationship between anger traits and somatization. Methods A cross-section design was conducted and 2008 college students were recruited from a comprehensive university in Shanghai. All participants finished questionnaires including Symptom Check List- 90 (SCL-90), State-Trait Anger Expression Inventory 2 (STAXI-2, Chinese version) and Family Adaptability and Cohesion Scale, second edition (FACES II, Chinese Version) to assess their degree of current somatization, anger trait and family function. Hierarchical linear regression analysis (Enter) was conducted respectively for men and women to examine the moderation effect of family cohesion and family adaptability in the association between anger and somatization. Results Somatic symptoms were significantly linked in the expected directions with depression and anger trait for both genders. Family cohesion and family adaptability were negatively associated with somatic symptoms. For female college students family cohesion was found to moderate the link between anger trait and somatization, but for male college students the moderation effect of family cohesion was marginally significant. The moderating role of family adaptability was significant for neither male nor female after current depressive symptoms were accounted for. Conclusion Proneness to anger is an independent predictor of somatization. For women, a high level of family cohesion was a protective factor which could reduce the influence of anger trait on somatic symptoms. Without comorbidity of current depression, family adaptability to some degree exempted individuals with anger proneness from developing somatic complaints. Interventions that integrate family cohesion cultivation, family flexibility fostering and depression treatment might be more effective for somatic patients high in anger trait. PMID:28769543

Failure strengths of denture teeth fabricated on injection molded or compression molded denture base resins.

PubMed

Robison, Nathan E; Tantbirojn, Daranee; Versluis, Antheunis; Cagna, David R

2016-08-01

Denture tooth fracture or debonding remains a common problem in removable prosthodontics. The purpose of this in vitro study was to explore factors determining failure strengths for combinations of different denture tooth designs (shape, materials) and injection or compression molded denture base resins. Three central incisor denture tooth designs were tested: nanohybrid composite (NHC; Ivoclar Phonares II), interpenetrating network (IPN; Dentsply Portrait), and microfiller reinforced polyacrylic (MRP; VITA Physiodens). Denture teeth of each type were processed on an injection molded resin (IvoBase HI; Ivoclar Vivadent AG) or a compression molded resin (Lucitone 199; Dentsply Intl) (n=11 or 12). The denture teeth were loaded at 45 degrees on the incisal edge. The failure load was recorded and analyzed with 2-way ANOVA (α=.05), and the fracture mode was categorized from observed fracture surfaces as cohesive, adhesive, or mixed failure. The following failure loads (mean ±SD) were recorded: NHC/injection molded 280 ±52 N; IPN/injection molded 331 ±41 N; MRP/injection molded 247 ±23 N; NHC/compression molded 204 ±31 N; IPN/compression molded 184 ±17 N; MRP/compression molded 201 ±16 N. Injection molded resin yielded significantly higher failure strength for all denture teeth (P<.001), among which IPN had the highest strength. Failure was predominantly cohesive in the teeth, with the exception of mixed mode for the IPN/compression group. When good bonding was achieved, the strength of the structure (denture tooth/base resin combination) was determined by the strength of the denture teeth, which may be affected by the processing technique. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Repair Strength in Simulated Restorations of Methacrylate- or Silorane-Based Composite Resins.

PubMed

Consani, Rafael Leonardo Xediek; Marinho, Tatiane; Bacchi, Atais; Caldas, Ricardo Armini; Feitosa, Victor Pinheiro; Pfeifer, Carmem Silvia

2016-01-01

The study verified the bond strength in simulated dental restorations of silorane- or methacrylate-based composites repaired with methacrylate-based composite. Methacrylate- (P60) or silorane-based (P90) composites were used associated with adhesive (Adper Single Bond 2). Twenty-four hemi-hourglass-shaped samples were repaired with each composite (n=12). Samples were divided according to groups: G1= P60 + Adper Single Bond 2+ P60; G2= P60 + Adper Single Bond 2 + P60 + thermocycling; G3= P90 + Adper Single Bond 2 + P60; and G4= P90 + Adper Single Bond 2 + P60 + thermocycling. G1 and G3 were submitted to tensile test 24 h after repair procedure, and G2 and G4 after submitted to 5,000 thermocycles at 5 and 55 ?#61616;C for 30 s in each bath. Tensile bond strength test was accomplished in an universal testing machine at crosshead speed of 0.5 mm/min. Data (MPa) were analyzed by two-way ANOVA and Tukey's test (5%). Sample failure pattern (adhesive, cohesive in resin or mixed) was evaluated by stereomicroscope at 30?#61655; and images were obtained in SEM. Bond strength values of methacrylate-based composite samples repaired with methacrylate-based composite (G1 and G2) were greater than for silorane-based samples (G3 and G4). Thermocycling decreased the bond strength values for both composites. All groups showed predominance of adhesive failures and no cohesive failure in composite resin was observed. In conclusion, higher bond strength values were observed in methacrylate-based resin samples and greater percentage of adhesive failures in silorane-based resin samples, both composites repaired with methacrylate-based resin.

Take a Tip from the Cubs

ERIC Educational Resources Information Center

Fornaciari, James

2016-01-01

As legendary Cubs manager Joe Maddon did with his players, seeing students as people first works for teachers who hope to build cohesive classes that achieve. Maddon's strength was his emphasis on cultivating positive relationships among his players. Taking a tip from Maddon's strategy, Fornaciari, an Advanced Placement history teacher, shares…

High School Improvement: Indicators of Effectiveness and School-Level Benchmarks

ERIC Educational Resources Information Center

National High School Center, 2012

2012-01-01

The National High School Center's "Eight Elements of High School Improvement: A Mapping Framework" provides a cohesive high school improvement framework comprised of eight elements and related indicators of effectiveness. These indicators of effectiveness allow states, districts, and schools to identify strengths and weaknesses of their current…

Relative scale and the strength and deformability of rock masses

NASA Astrophysics Data System (ADS)

Schultz, Richard A.

1996-09-01

The strength and deformation of rocks depend strongly on the degree of fracturing, which can be assessed in the field and related systematically to these properties. Appropriate Mohr envelopes obtained from the Rock Mass Rating (RMR) classification system and the Hoek-Brown criterion for outcrops and other large-scale exposures of fractured rocks show that rock-mass cohesive strength, tensile strength, and unconfined compressive strength can be reduced by as much as a factor often relative to values for the unfractured material. The rock-mass deformation modulus is also reduced relative to Young's modulus. A "cook-book" example illustrates the use of RMR in field applications. The smaller values of rock-mass strength and deformability imply that there is a particular scale of observation whose identification is critical to applying laboratory measurements and associated failure criteria to geologic structures.

Adhesion properties in systems of laminated pigmented polymers, carbon-graphite fiber composite framework and titanium surfaces in implant suprastructures.

PubMed

Segerström, Susanna; Ruyter, I Eystein

2009-09-01

For long-term stability the adhering interfaces of an implant-retained supraconstruction of titanium/carbon-graphite fiber-reinforced (CGFR) polymer/opaquer layer/denture base polymer/denture teeth must function as a unity. The aim was to evaluate adhesion of CGFR polymer to a titanium surface or CGFR polymer to two different opaquer layers/with two denture base polymers. Titanium plates were surface-treated and silanized and combined with a bolt of CGFR polymer or denture base polymer (Probase Hot). Heat-polymerized plates of CGFR polymer (47 wt% fiber) based on poly(methyl methacrylate) and a copolymer matrix were treated with an opaquer (Sinfony or Ropak) before a denture base polymer bolt was attached (Probase Hot or Lucitone 199). All specimens were heat-polymerized, water saturated (200 days) and thermally cycled (5000 cycles, 5/55 degrees C) before shear bond testing. Silicatized titanium surfaces gave higher bond strength to CGFR polymer (16.2+/-2.34 and 18.6+/-1.32) MPa and cohesive fracture than a sandblasted surface (5.9+/-2.11) MPa where the fracture was adhesive. The opaquer Sinfony gave higher adhesion values and mainly cohesive fractures than the opaquer Ropak. Different surface treatments (roughened or polished) of the CGFR polymer had no effect on bond strength. The fracture surfaces of silicatized titanium/CGFR polymer/opaquer layer (Sinfony)/denture base polymers were mainly cohesive. A combination of these materials in an implant-retained supraconstruction is promising for in vivo evaluation.

Durability and life prediction modeling in polyimide composites

NASA Technical Reports Server (NTRS)

Binienda, Wieslaw K.

1995-01-01

Sudden appearance of cracks on a macroscopically smooth surface of brittle materials due to cooling or drying shrinkage is a phenomenon related to many engineering problems. Although conventional strength theories can be used to predict the necessary condition for crack appearance, they are unable to predict crack spacing and depth. On the other hand, fracture mechanics theory can only study the behavior of existing cracks. The theory of crack initiation can be summarized into three conditions, which is a combination of a strength criterion and laws of energy conservation, the average crack spacing and depth can thus be determined. The problem of crack initiation from the surface of an elastic half plane is solved and compares quite well with available experimental evidence. The theory of crack initiation is also applied to concrete pavements. The influence of cracking is modeled by the additional compliance according to Okamura's method. The theoretical prediction by this structural mechanics type of model correlates very well with the field observation. The model may serve as a theoretical foundation for future pavement joint design. The initiation of interactive cracks of quasi-brittle material is studied based on a theory of cohesive crack model. These cracks may grow simultaneously, or some of them may close during certain stages. The concept of crack unloading of cohesive crack model is proposed. The critical behavior (crack bifurcation, maximum loads) of the cohesive crack model are characterized by rate equations. The post-critical behavior of crack initiation is also studied.

Electrochemically deposited conducting polymers for reliable biomedical interfacing materials: Formulation, mechanical characterization, and failure analysis

NASA Astrophysics Data System (ADS)

Qu, Jing

Conjugated polymers such as poly(3,4-ethylenedioxythiophene) (PEDOT) are of interest for a variety of applications including interfaces between electronic biomedical devices and living tissue. These polymers provide an improved interface compared to metal and semiconducting electrodes because of their ionic conductivity, relatively lower stiffness, and ability to incorporate biological molecules. Even though the signal transfer and biocompatibility of conjugated polymers are superior compared as the biointerfacing materials, the durability has been the weakest part for the long-term applications. Even though some efforts have been made to improve the durability of conjugated polymers, little quantitative information of the improved cohesion, adhesion and durability has been reported. In this thesis, the methods of improving the durability of conjugated polymer films, especially PEDOT, were investigated, including alternating the processing methods and components in synthesis. The 7-month in vivo testing showed that the durability of PEDOT films still needed to be improved. As a coating for biosignal transfer, the cohesion, adhesion and electrochemical stability of PEDOT are vital to determine the long-term performance. Not much information hd been developed around the cohesion and adhesion. A thin film cracking method was developed to measure the stiffness, strength and the interfacial shear strength (adhesion) of electrochemically deposited PEDOT. The estimated Young’s modulus of the PEDOT films was 2.6 ± 1.4 GPa, and the strain to failure was around 2%. The tensile strength was measured to be 56 ± 27 MPa. The effectiveness of crosslinker and adhesion promoter was demonstrated by this method. It was shown that 5 mole% addition of a tri-functional EDOT crosslinker (EPh) increased the tensile strength of the films to 283 ± 67 MPa, while the strain to failure remained about the same (2%). With the modification of EDOT-acid to the surface of stainless steel substrate, the interfacial shear strength was improved from 11.8 MPa to 32.5 MPa. To correlate the adhesion with the durability of PEDOT coatings, a tribology test was introduced. It was found that the durability of PEDOT on Au electrode was much exceptionally good, and even better than the adhesion promoted coatings with EDOT-acid on stainless steel and ITO substrates. The characterization method developed in this thesis made a critical difference in systematically comparing different materials, and provided valuable information for materials development and selection.

The role of heterogeneous fluid pressures in the shape of critical-taper submarine wedges, with application to Barbados

NASA Astrophysics Data System (ADS)

Yeh, En-Chao; Suppe, John

2014-05-01

Some classic accretionary wedges such as Nankai trough and Barbados are mechanically heterogeneous based on their spatial variation in taper, showing inward decrease in surface slope α without covariation in detachment dip β. Possible sources of regional heterogeniety include variation in fluid pressure, density, cohesion and fault strength, which can be constrained by the seismic or borehole observable parameter, fluid-retention depth Z_FRD, below which compaction is strongly diminished. In particular the Hubbert-Rubey fluid-pressure weakening can be addressed as (1-lambda)~0.6Z_FRD/Z. We recast the heterogeneous critical-taper wedge theory of Dahlen (1990) in terms of the observable Z_FRD/H, where H is the detachment depth, which allows for real world applications. For example, seismic velocity and borehole data from the Barbados shows that the fluid-retention depth Z_FRD is approximately constant and Z_FRD/H decreases inward. This leads to a factor of four inward decreases in wedge strength, dominated by fluid pressure, with only a second-order role for density and cohesion. An inward decrease in wedge strength should by itself produce an increase in taper, therefore the observed decreasing taper must be dominated by decreasing fault strength mu_b* from 0.03 to 0.01. Static fluid-pressures along the detachment in equilibrium with the overlying wedge predict the observed wedge geometry well, given a constant intrinsic friction coefficient mu_b=0.15.

Direct Tensile Strength and Characteristics of Dentin Restored with All-Ceramic, Resin-Composite, and Cast Metal Prostheses Cemented with Resin Adhesives

PubMed Central

Piemjai, Morakot; Nakabayashi, Nobuo

2015-01-01

A dentin-cement-prosthesis complex restored with either all-porcelain, cured resin-composite, or cast base metal alloy and cemented with either of the different resin cements was trimmed into a mini-dumbbell shape for tensile testing. The fractured surfaces and characterization of the dentin-cement interface of bonded specimens were investigated using a Scanning Electron Microscope. A significantly higher tensile strength of all-porcelain (12.5 ± 2.2 MPa) than that of cast metal (9.2 ± 3.5 MPa) restorations was revealed with cohesive failure in the cement and failure at the prosthesis-cement interface in Super-Bond C&B group. No significant difference in tensile strength was found among the types of restorations using the other three cements with adhesive failure on the dentin side and cohesive failure in the cured resin. SEM micrographs demonstrated the consistent hybridized dentin in Super-Bond C&B specimens that could resist degradation when immersed in hydrochloric acid followed by NaOCl solutions whereas a detached and degraded interfacial layer was found for the other cements. The results suggest that when complete hybridization of resin into dentin occurs tensile strength at the dentin-cement is higher than at the cement-prosthesis interfaces. The impermeable hybridized dentin can protect the underlying dentin and pulp from acid demineralization, even if detachment of the prosthesis has occurred. PMID:26539520

Correlation between surface carbon concentration and adhesive strength at the Si cell/EVA interface in a PV module

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dhere, N.G.; Wollam, M.E.; Gadre, K.S.

1997-12-31

Silicon solar cell/EVA composite is being studied with an objective to further improve the manufacturing technology of PV modules. Sample extraction and adhesion strength measurement process has been modified. Silicon and EVA samples were extracted from solar cells of new and field-deployed modules. Optical microscopy, SEM, and AES of samples from new modules revealed EVA islands covering most of the silicon cell surface indicating a cohesive failure. A good correlation was observed between the adhesive strength and surface concentration of carbon. A low carbon concentration which indicated less EVA clinging to cell surface always resulted in low adhesive strengths. Themore » correlation provides a simple technique for inferring properties of EVA.« less

Cohesion and coordination effects on transition metal surface energies

NASA Astrophysics Data System (ADS)

Ruvireta, Judit; Vega, Lorena; Viñes, Francesc

2017-10-01

Here we explore the accuracy of Stefan equation and broken-bond model semiempirical approaches to obtain surface energies on transition metals. Cohesive factors are accounted for either via the vaporization enthalpies, as proposed in Stefan equation, or via cohesive energies, as employed in the broken-bond model. Coordination effects are considered including the saturation degree, as suggested in Stefan equation, employing Coordination Numbers (CN), or as the ratio of broken bonds, according to the bond-cutting model, considering as well the square root dependency of the bond strength on CN. Further, generalized coordination numbers CN bar are contemplated as well, exploring a total number of 12 semiempirical formulations on the three most densely packed surfaces of 3d, 4d, and 5d Transition Metals (TMs) displaying face-centered cubic (fcc), body-centered cubic (bcc), or hexagonal close-packed (hcp) crystallographic structures. Estimates are compared to available experimental surface energies obtained extrapolated to zero temperature. Results reveal that Stefan formula cohesive and coordination dependencies are only qualitative suited, but unadvised for quantitative discussion, as surface energies are highly overestimated, favoring in addition the stability of under-coordinated surfaces. Broken-bond cohesion and coordination dependencies are a suited basis for quantitative comparison, where square-root dependencies on CN to account for bond weakening are sensibly worse. An analysis using Wulff shaped averaged surface energies suggests the employment of broken-bond model using CN to gain surface energies for TMs, likely applicable to other metals.

Flow-induced Development of Unicellular Cyanobacterial Mats

NASA Astrophysics Data System (ADS)

Gong, J.; Tice, M. M.

2011-12-01

Microbial mats/biofilms are abundant microbial growth structures throughout the history of life on Earth. Understanding the mechanisms for their morphogenesis and interactions with physical sedimentary forces are important topics that allow deeper understanding of related records. When subjected to hydrodynamic influences, mats are known to vary in morphology and structure in response to fluid shear, yet mechanistically, the underlying cellular architecture due to interactions with flow remain unexplained. Moreover, mats are found to emerge larger scale roughness elements and modified cohesive strength growing under flow. It is a mystery how and why these mat-community-level features are linked in association with modified boundary layers at the mats surface. We examined unicellular cyanobacterium Synechocystis sp. PCC 6803 in a circular flow bioreactor designed to maintain a fixed set of hydrodynamic conditions. The use of monoculture strains and unidirectional currents, while not replicating natural mat systems (almost certainly multi-species and often multi-directional currents under complex wind or tidal wave actions), helps to simplify these systems and allows for specific testing of hypotheses regarding how mats evolve distinctive morphologies induced by flow. The unique design of the reactor also makes measurements such as critical erosional shear stress of the mats possible, in addition to microscopic, macroscopic imaging and weeks of continuous mats growth monitoring. We report the finding that linear chains, filament-like cell groups were present from unicellular cyanobacterial mats growing under flow (~1-5 cm/s) and these structures are organized within ~1-3mm size streamers and ~0.5-1mm size nodular macrostructures. Ultra-small, sub-micron thick EPS strings are observed under TEM and are likely the cohesive architectural elements in mats across different fluid regimes. Mat cohesion generally grows with and adapts to increasing flow shear stress within certain limits. Overall topological roughness of the mats were analyzed and estimated in terms of the skin friction of the mats surfaces interacting with flow. Then, together with the critical erosional cohesive strength of the mats estimated, we present a theoretical physical model linking morphology and material strength of mats to overlying fluid flow. If this model were further tested true, it suggests that physical flows may very well have a controlling effect on the properties of mats growing within it.

Influence of ultrasound and diamond burs treatments on microtensile bond strength.

PubMed

Conde, Alexandre; Mainieri, Vivian; Mota, Eduardo Goncalves; Oshima, Hugo Mitsuo

2012-01-01

To compare surface treatments with CVDentUS ultrasound tips (UT) and KGSorensen diamond burs (DB) on etched (e) and non-etched (n/e) dentin. The microtensile bond strength (μTBS) was measured and fractography was assessed by scanning electron microscope (SEM). Sixteen molars were divided into four groups of four teeth each according to treatment (DB-n/e; DB-e; UT-n/e; UT-e). The teeth were restored, sectioned into samples for μTBS (n=40) and tested on a EMIC DL-2000 universal machine (0.5 mm/min) and analyzed by SEM for fracture classification. For analysis of the data on μTBS, the two-way ANOVA, using treatment and acid etching as fixed factor, and the Tukey test were used (α=0.05). To failures classification in cohesive in dentin (CD); cohesive in composite resin (CC); cohesive interfacial on base or top of hybrid layer (CBT); cohesive in adhesive (CA); mixed (M); interfacial on smear layer (S) the Fisher's exact test (α=0.05) was performed. The mean values of μTBS (in MPa) in the different groups were as follows: UT-e: 45.31 ± 8.16; DB-e: 34.04 ± 9.29; UT-n/e: 15.17 ± 3.71; and DB-n/e: 9.86 ± 3.80. On analysis of the SEM micrographs, the DB-n/e group showed total obstruction of dentinal tubules; the UT-n/e group showed partial desobstruction of dentinal tubules and irregular surface; the DB-e group showed complete desobstruction of dentinal tubules; and the UT-e group showed complete desobstruction of dentinal tubules and irregular surface. The combination of ultrasound treatment and acid etching provides high values of μTBS. An association exists between CA/CC failures and the UT method, CBT failure and the DB method, CBT/CC failures and etching, S failure and non-etching.

Graphemic Cohesion Effect in Reading and Writing Complex Graphemes

ERIC Educational Resources Information Center

Spinelli, Elsa; Kandel, Sonia; Guerassimovitch, Helena; Ferrand, Ludovic

2012-01-01

"AU" /o/ and "AN" /a/ in French are both complex graphemes, but they vary in their strength of association to their respective sounds. The letter sequence "AU" is systematically associated to the phoneme /o/, and as such is always parsed as a complex grapheme. However, "AN" can be associated with either one…

A Numerical Study on the Edgewise Compression Strength of Sandwich Structures with Facesheet-Core Disbonds

NASA Technical Reports Server (NTRS)

Bergan, Andrew C.

2017-01-01

Damage tolerant design approaches require determination of critical damage modes and flaw sizes in order to establish nondestructive evaluation detection requirements. A finite element model is developed to assess the effect of circular facesheet-core disbonds on the strength of sandwich specimens subjected to edgewise compressive loads for the purpose of predicting the critical flaw size for a variety of design parameters. Postbuckling analyses are conducted in which an initial imperfection is seeded using results from a linear buckling analysis. Both the virtual crack closure technique (VCCT) and cohesive elements are considered for modeling disbond growth. Predictions from analyses using the VCCT and analyses using cohesive elements are in good correlation. A series of parametric analyses are conducted to investigate the effect of core thickness and material, facesheet layup, facesheet-core interface properties, and curvature on the criticality of facesheet-core disbonds of various sizes. The results from these analyses provide a basis for determining the critical flaw size for facesheet-core disbonds subjected to edgewise compression loads and, therefore, nondestructive evaluation flaw detection requirements for this configuration.

Conformational dynamics and internal friction in homopolymer globules: equilibrium vs. non-equilibrium simulations.

PubMed

Einert, T R; Sing, C E; Alexander-Katz, A; Netz, R R

2011-12-01

We study the conformational dynamics within homopolymer globules by solvent-implicit Brownian dynamics simulations. A strong dependence of the internal chain dynamics on the Lennard-Jones cohesion strength ε and the globule size N (G) is observed. We find two distinct dynamical regimes: a liquid-like regime (for ε < ε(s) with fast internal dynamics and a solid-like regime (for ε > ε(s) with slow internal dynamics. The cohesion strength ε(s) of this freezing transition depends on N (G) . Equilibrium simulations, where we investigate the diffusional chain dynamics within the globule, are compared with non-equilibrium simulations, where we unfold the globule by pulling the chain ends with prescribed velocity (encompassing low enough velocities so that the linear-response, viscous regime is reached). From both simulation protocols we derive the internal viscosity within the globule. In the liquid-like regime the internal friction increases continuously with ε and scales extensive in N (G) . This suggests an internal friction scenario where the entire chain (or an extensive fraction thereof) takes part in conformational reorganization of the globular structure.

Acculturation, enculturation, and symptoms of depression in Hispanic youth: the roles of gender, Hispanic cultural values, and family functioning.

PubMed

Lorenzo-Blanco, Elma I; Unger, Jennifer B; Baezconde-Garbanati, Lourdes; Ritt-Olson, Anamara; Soto, Daniel

2012-10-01

The risk for depression increases as Hispanic youth acculturate to U.S. society. This association is stronger for Hispanic girls than boys. To better understand the influence of culture and family on depressive symptoms, we tested a process-oriented model of acculturation, cultural values, and family functioning. The data came from Project RED, which included 1,922 Hispanic students (53 % girls; 86 % were 14 years old; and 84 % were U.S. born) from Southern California. We used data from 9th to 11th grade to test the influence of acculturation-related experiences on depressive symptoms over time. Multi-group structural equation analysis suggested that both family conflict and cohesion were linked with depressive symptoms. Hispanic cultural values were associated with family cohesion and conflict but the strength and direction of these relationships varied across cultural values and gender. For girls and boys, familismo and respeto were associated with higher family cohesion and lower family conflict. Moreover, gender roles were linked with higher family cohesion in girls but not in boys. These results indicate that improving family functioning will be beneficial for boys' and girls' psychological well-being. This may be achieved by promoting familismo and respeto for boys and girls and by promoting traditional gender roles for girls.

Acculturation, Enculturation, and Symptoms of Depression in Hispanic Youth: The Roles of Gender, Hispanic Cultural Values, and Family Functioning

PubMed Central

Unger, Jennifer B.; Baezconde-Garbanati, Lourdes; Ritt-Olson, Anamara; Soto, Daniel

2015-01-01

The risk for depression increases as Hispanic youth acculturate to U.S. society. This association is stronger for Hispanic girls than boys. To better understand the influence of culture and family on depressive symptoms, we tested a process-oriented model of acculturation, cultural values, and family functioning. The data came from Project RED, which included 1,922 Hispanic students (53 % girls; 86 % were 14 years old; and 84 % were U.S. born) from Southern California. We used data from 9th to 11th grade to test the influence of acculturation-related experiences on depressive symptoms over time. Multi-group structural equation analysis suggested that both family conflict and cohesion were linked with depressive symptoms. Hispanic cultural values were associated with family cohesion and conflict but the strength and direction of these relationships varied across cultural values and gender. For girls and boys, familismo and respeto were associated with higher family cohesion and lower family conflict. Moreover, gender roles were linked with higher family cohesion in girls but not in boys. These results indicate that improving family functioning will be beneficial for boys’ and girls’ psychological well-being. This may be achieved by promoting familismo and respeto for boys and girls and by promoting traditional gender roles for girls. PMID:22627624

Study to Investigate the Effects of Skin Friction on the Performance of Drilled Shafts in Cohesive Soils. Volumes I, II, III.

DTIC Science & Technology

1982-03-01

2) after Marsland and Randolph (1977) represents the peak un- drained shear strength. Torvane tests were also run in the field on Shelby tube ...The laboratory test results were characterized in terms of: 4 a. stratigraphy; b. stress state; c. undrained, drained and residual shear strengths; d...in Figure 3 as P- 1. A Shelby tube could not be retrieved at 14-ft depth in Boring B-2. A new boring (Boring B-2A) was made 6 in. further away from

Effect of Pressure in Thermoplastic Ribbon Thermal Welding

NASA Technical Reports Server (NTRS)

Hinkley, J. A.; Messier, B. C.; Marchello, J. M.

1996-01-01

An inexpensive apparatus was designed to simulate some features of on-the-fly thermal welding in heated-head tow placement. Previous studies have shown how ply/ply weld strength depends on weld time/temperature history. The apparatus has been modified recently to apply higher contact forces. Welding at pressures up to 1.7MPa (250psi) produced more consistent welds and fewer intra-ply voids, This has permitted a study of the conditions required for achieving the limiting ply/ply cohesive strength in simulated tow placement of a polyimide oligomer.

Supercritical CO2 fluid-foaming of polymers to increase porosity: a method to improve the mechanical and biocompatibility characteristics for use as a potential alternative to allografts in impaction bone grafting?

PubMed

Tayton, Edward; Purcell, M; Aarvold, A; Smith, J O; Kalra, S; Briscoe, A; Shakesheff, K; Howdle, S M; Dunlop, D G; Oreffo, R O C

2012-05-01

Disease transmission, availability and cost of allografts have resulted in significant efforts to find an alternative for use in impaction bone grafting (IBG). Recent studies identified two polymers with both structural strength and biocompatibility characteristics as potential replacements. The aim of this study was to assess whether increasing the polymer porosity further enhanced the mechanical and cellular compatibility characteristics for use as an osteogenic biomaterial alternative to allografts in IBG. Solid and porous poly(DL-lactide) (P(DL)LA) and poly(DL-lactide-co-glycolide) (P(DL)LGA) scaffolds were produced via melt processing and supercritical CO(2) foaming, and the differences characterized using scanning electron microscopy (SEM). Mechanical testing included milling and impaction, with comparisons made using a shear testing rig as well as a novel agitation test for cohesion. Cellular compatibility tests for cell number, viability, and osteogenic differentiation using WST-1 assays, fluorostaining, and ALP assays were determined following 14 day culture with skeletal stem cells. SEM showed excellent porosity throughout both of the supercritical-foam-produced polymer scaffolds, with pores between 50 and 200 μm. Shear testing showed that the porous polymers exceeded the shear strength of allograft controls (P<0.001). Agitation testing showed greater cohesion between the particles of the porous polymers (P<0.05). Cellular studies showed increased cell number, viability, and osteogenic differentiation on the porous polymers compared to solid block polymers (P<0.05). The use of supercritical CO(2) to generate porous polymeric biodegradable scaffolds significantly improves the cellular compatibility and cohesion observed compared to non-porous counterparts, without substantial loss of mechanical shear strength. These improved characteristics are critical for clinical translation as a potential osteogenic composite for use in IBG. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Nanostructured Composites: Effective Mechanical Property Determination of Nanotube Bundles

NASA Technical Reports Server (NTRS)

Saether, E.; Pipes, R. B.; Frankland, S. J. V.

2002-01-01

Carbon nanotubes naturally tend to form crystals in the form of hexagonally packed bundles or ropes that should exhibit a transversely isotropic constitutive behavior. Although the intratube axial stiffness is on the order of 1 TPa due to a strong network of delocalized bonds, the intertube cohesive strength is orders of magnitude less controlled by weak, nonbonding van der Waals interactions. An accurate determination of the effective mechanical properties of nanotube bundles is important to assess potential structural applications such as reinforcement in future composite material systems. A direct method for calculating effective material constants is developed in the present study. The Lennard-Jones potential is used to model the nonbonding cohesive forces. A complete set of transverse moduli are obtained and compared with existing data.

Microstructure and Properties of Thermally Sprayed Functionally Graded Coatings for Polymeric Substrates

NASA Technical Reports Server (NTRS)

Ivosevic, M.; Knight, R.; Kalidindi, S. R.; Palmese, G. R.; Sutter, J. K.

2003-01-01

The use of polymer matrix composites (PMCs) in the gas flow path of advanced turbine engines offers significant benefits for aircraft engine performance but their useful lifetime is limited by their poor erosion resistance. High velocity oxy-fuel (HVOF) sprayed polymer/cermet functionally graded (FGM) coatings are being investigated as a method to address this technology gap by providing erosion and oxidation protection to polymer matrix composites. The FGM coating structures are based on a polyimide matrix filled with varying volume fractions of WC-Co. The graded coating architecture was produced using a combination of internal and external feedstock injection, via two computer-controlled powder feeders and controlled substrate preheating. Porosity, coating thickness and volume fraction of the WC-Co filler retained in the coatings were determined using standard metallographic techniques and computer image analysis. The pull-off strength (often referred to as the adhesive strength) of the coatings was evaluated according to the ASTM D 4541 standard test method, which measured the greatest normal tensile force that the coating could withstand. Adhesive/cohesive strengths were determined for three different types of coating structures and compared based on the maximum indicated load and the surface area loaded. The nature and locus of the fractures were characterized according to the percent of adhesive and/or cohesive failure, and the tested interfaces and layers involved were analyzed by Scanning Electron Microscopy.

Dependence of ripple dimensions on cohesive and non-cohesive bed properties in the intertidal Dee Estuary

NASA Astrophysics Data System (ADS)

Lichtman, Ian; Thorne, Peter; Baas, Jacobus; O'Boyle, Louise; Cooke, Richard; Amoudry, Laurent; Bell, Paul; Aspden, Rebecca; Bass, Sarah; Davies, Alan; Hope, Julie; Malarkey, Jonathan; Manning, Andrew; Parsons, Daniel; Paterson, David; Peakall, Jeffrey; Schindler, Robert; Ye, Leiping

2014-05-01

There is a need to better understand the effects of cohesive and mixed sediments on coastal processes, to improve sediment transport models for the management of coastal erosion, siltation of navigation channels and habitat change. Although reasonable sediment transport predictors are available for pure sands, it still is not the case for mixed cohesive and non-cohesive sediments. Existing predictors mostly relate ripple dimensions to hydrodynamic conditions and median sediment grain diameter, assuming a narrow unimodal particle size distribution. Properties typical of mixed conditions, such as composition and cohesion for example, are not usually taken into account. This presents severe shortcomings to predictors' abilities. Indeed, laboratory experiments using mixed cohesive sediments have shown that bedform dimensions decrease with increasing bed mud content. In the field, one may expect current predictors to match data for well-sorted sands closely, but poorly for mixed sediments. Our work is part of the COHBED project and aims to: (1) examine, in field conditions, if ripple dimensions are significantly different for mixed cohesive sediment beds compared to beds with pure sand; (2) compare the field data with laboratory results that showed reduced ripple length due to cohesive mud content; and (3) assess the performance of a selection of ripple predictors for mixed sediment data. The COHBED project was set up to undertake laboratory experiments and fieldwork to study how physical and biological processes influence bedform development in a mixed cohesive-cohesionless sediment environment. As part of COHBED, a suite of instruments was deployed on tidal flats in the Dee Estuary (on the NW coast of England), collecting co-located measurements of the hydrodynamics, suspended sediment properties and bed morphology. The instruments occupied three sites collecting data over different bed compositions during a two week period (21 May to 4 June 2013). One site was located above a sandy bed, and the two others were above mixed beds of different mud content. The tide covered a full cycle from neaps to neaps and the weather provided onshore and offshore winds of varying strength. Bedform measurements were taken every half an hour using an Acoustic Ripple Profiler (ARP) that covered an area of about two square metres. Dynamic measurements of tides and waves were made using an Acoustic Doppler Velocimeter (ADV) at 8 Hz. Bed samples were taken when the tidal flats dried out at low tide and a sediment trap collected suspended load near the bed. In the presentation, comparisons of the sites will be made from measurements of the proportion of mud and biological sediment binders at each site and the ripple dimensions for different hydrodynamic conditions. Key words: bed morphology, current ripple, mixed sediment, cohesion, hydrodynamics, observations, tidal flat, estuary, Dee

Fluid Centrality: A Social Network Analysis of Social-Technical Relations in Computer-Mediated Communication

ERIC Educational Resources Information Center

Enriquez, Judith Guevarra

2010-01-01

In this article, centrality is explored as a measure of computer-mediated communication (CMC) in networked learning. Centrality measure is quite common in performing social network analysis (SNA) and in analysing social cohesion, strength of ties and influence in CMC, and computer-supported collaborative learning research. It argues that measuring…

Seasonal change of WEPP erodibility parameters on a fallow plot

Treesearch

D. K. McCool; S. Dun; J. Q. Wu; W. J. Elliot

2011-01-01

In cold regions, frozen soil has a significant influence on runoff and water erosion. Frozen soil can reduce infiltration capacity, and the freeze-thaw processes degrade soil cohesive strength and increase soil erodibility. In the Inland Pacific Northwest of the USA, major erosion events typically occur during winter from low-intensity rain, snowmelt, or both as frozen...

Multi-Scale Fracture Mechanics of 3-D Reinforced Composites

DTIC Science & Technology

2010-02-26

cohesive energy over the interface between plies n and n+1, separated by the horizontal surface z= zn is w/ g(KB)ds (16) In this case the normal vector...where INP is the total number of integration points and V„ is the volume of the n-th ply. Note that the random distribution of initial strength ( 31

The effect of biological cohesion on current ripple development

NASA Astrophysics Data System (ADS)

Malarkey, Jonathan; Baas, Jaco H.; Hope, Julie

2014-05-01

Results are presented from laboratory experiments examining the role of biological cohesion, associated with Extra Polymeric Substances, on the development of current ripples. The results demonstrate the importance of biological cohesion compared to the effect of physical cohesion associated with clays in an otherwise sandy bed. FURTHER INFORMATION In fluvial and marine environments sediment transport is mainly dependent on the nature of the bed surface (rippled or flat) and the nature of cohesion in the bed. Cohesion can be either physical, as a result of the presence of clays, or biological as a result of the presence of organisms. In the case of the latter, biological cohesion occurs as a result of the presence of Extra Polymeric Substances (EPS) secreted by microorganisms. While it is known that EPS can dramatically increase the threshold of motion (Grant and Gust, 1987), comparatively little is known about the effect of EPS on ripple formation and development. The experiments described here seek to fill this gap. They also allow the effect of biological cohesion to be compared with that of physical cohesion from previous experiments (Baas et al., 2013). The experiments, which were conducted in a 10m flume at Bangor University, involved a current over a bed made of fine sand, with a median diameter of 0.148mm, and various amounts of xanthan gum, a proxy for naturally occurring EPS (Vardy et al., 2007). The hydrodynamic experimental conditions were matched very closely to those of Baas et al. (2013). The ripple dimensions were recorded through the glass side wall of the tank using time lapse photography. In the physical cohesion experiments of Baas et al. (2013) for clay contents up to 12%, the clay was very quickly winnowed out of the bed, leaving essentially clay-free ripples that developed at more or less the same rate as clean sand ripples. The resulting equilibrium ripples were essentially the same length as the clean sand ripples but reduced in height. By contrast, the biological cohesion experiments resulted in a drastic slowing down in ripple development, for much smaller amounts of xanthan (< 1/8%), but resulted in equilibrium ripples with the same dimensions as abiotic sand. This difference in effect for biological and physical cohesion is thought to be related to differences in the nature of the binding. In particular, sand grains with biological cohesion are inhibited from moving independently, which is crucial to ripple development. This work has profound implications for sediment transport studies and emphasises the importance of considering biology as well as clays in sediments. ACKNOWLEDGEMENTS This work was funded by the UK Natural Environment Research Council (NERC) under the 'COHBED' project (NE/1027223/1). REFERENCES Baas, J.H., Davies, A.G. and Malarkey, A.G. (2013) Bedform development in mixed sand-mud: the contrasting role of cohesive forces in flow and bed. Geomorphology, 182, 19-32. Grant, J. and Gust, G. (1987) Prediction of coastal sediment stability from photopigment content of mats of purple sulfur bacteria. Nature, 330, 244-246. Vardy, S., Saunders, J.E., Tolhurst, T.J., Davies, P.A., and Paterson, D.M. (2007) Calibration of the high-pressure cohesive strength meter (CSM). Continental Shelf Research, 27, 1190-1199.

Effective leadership, teamwork and mentoring--essential elements in promoting generational cohesion in the nursing workforce and retaining nurses.

PubMed

Nelsey, Lorraine; Brownie, Sonya

2012-01-01

Despite recent increases in nurse recruitment in Australia, the current nursing workforce is still below the predicted numbers for the future demands. The combination of an ageing workforce, high nursing staff turnover and an inability to attract and retain nurses is eroding the capacity of the health care sector to appropriately respond to the care needs of the community. Currently, the nursing workforce may have as many as four generations working together. Differences in employment needs and values, work ethics, attitudes towards authority, and professional aspirations, contribute to some of the cross-generational problems that emerge and the turnover of nursing staff. Strategies to improve the retention rates of nurses need to focus on building a cohesive workforce by utilising the strengths and skill sets that characterise different generations of nurses, and creating the conditions in which nurses across all generations feel supported and valued. The aim of this article is to explain how effective leadership, teamwork and mentoring can assist efforts to promote generational cohesion and address the decline in the number of nurses in the workforce.

Portraying the Contribution of Individual Behaviors to Team Cohesion and Performance

NASA Technical Reports Server (NTRS)

Parke, Bonny; Orasanu, Judith

2012-01-01

Behaviors of individuals in teams both contribute to and are molded by team dynamics. How they do so has been the subject of much research. A method of portraying individuals' behaviors in teams, the Team Diagramming Method (TDM) is presented. Behaviors are rated by other team members on three important dimensions: positivity/negativity, dominant/submissive, and task-orientedness/expressiveness. A study of 5-person teams engaging in a 3-day moon simulation task demonstrated that measures of these perceived behaviors as well as the variances of these behaviors correlated with cohesion measures and performance. The method shows strengths and weaknesses of particular teams and, by comparison with high-performing teams, suggests interventions based on individual as well as team behaviors. The primary goal of this study was to determine the extent to which these team level variables, derived from all team members' rated behaviors, were associated with previous methods of measuring cohesion and with performance. A secondary goal was to determine the stability of TDM measures over time by comparing team level variables based on ratings early and later in the team s work together.

Failure modes and conditions of a cohesive, spherical body due to YORP spin-up

NASA Astrophysics Data System (ADS)

Hirabayashi, Masatoshi

2015-12-01

This paper presents transition of the failure mode of a cohesive, spherical body due to The Yarkovsky-O'Keefe-Radzievskii-Paddack (YORP) spin-up. On the assumption that the distribution of materials in the body is homogeneous, failed regions first appearing in the body at different spin rates are predicted by comparing the yield condition of an elastic stress in the body. It is found that as the spin rate increases, the locations of the failed regions move from the equatorial surface to the central region. To avoid such failure modes, the body should have higher cohesive strength. The results by this model are consistent with those by a plastic finite element model. Then, this model and a two-layered-cohesive model first proposed by Hirabayashi et al. are used to classify possible evolution and disruption of a spherical body. There are three possible pathways to disruption. First, because of a strong structure, failure of the central region is dominant and eventually leads to a breakup into multiple components. Secondly, a weak surface and a weak interior make the body oblate. Thirdly, a strong internal core prevents the body from failing and only allows surface shedding. This implies that observed failure modes may highly depend on the internal structure of an asteroid, which could provide crucial information for giving constraints on the physical properties.

Scaling and Predicting the Geotechnical Resistance Provided by Alfalfa in Experimental Studies of Alluvial-Channel Morphology and Planform

NASA Astrophysics Data System (ADS)

Bankhead, N.; Simon, A.

2008-12-01

Several complex interactions occur between riparian vegetation and bank stability processes. Although there are both positive and negative effects of riparian vegetation on streambank stability, a link between increased vegetation density and decreased bank erosion and lateral migration rates of channels has generally been recorded. The ability of vegetation to promote increased bank stability leads to a positive feedback, in which bank stability then allows the growth and establishment of more vegetation. To study interactions between vegetation density and channel planform, past flume studies have used alfalfa sprouts (Medicago sativa), seeded over the entire floodplain in varying densities. Such studies have observed reductions in braiding intensity with increased alfalfa density. It has been assumed in these studies that the alfalfa sprouts increase the resistance of the bank material to lateral erosion. When alfalfa sprouts are scaled up they simulate mature riparian trees well. However, the geotechnical properties of alfalfa roots, and quantification of the increase in resistance provided to the banks under different densities of alfalfa have thus far been ignored. It is therefore unknown if the resistance provided by the alfalfa roots also scales well to real-world root-reinforcement values. To quantify additional bank strength, alfalfa sprouts were grown in sand and the roots tested at regular intervals to measure tensile strength. Results of tensile-strength measurements for alfalfa sprouts displayed the typical non-linear decrease of tensile strength (in MPa) with increasing root diameter. Values for the additional cohesion provided by alfalfa roots were calculated by inputting alfalfa tensile-strength and root density data to the root-reinforcement model, RipRoot, resulting in root-reinforcement values of 0 to 11.8 kPa. These values are similar to those that would be expected under field conditions. The root-cohesion values calculated for alfalfa sprouts were then used in conjunction with the Bank Stability and Toe Erosion Model (BSTEM), and a series of laboratory experiments, to evaluate if the factor of safety (FS) of experimental channels lined with different densities of alfalfa could be predicted. Sand banks ranging in height from 1.25 to 3.75 cm were modeled and tested experimentally for cases with different groundwater heights and flow depths in the channel, and with cohesion due to roots being scaled appropriately using a length reduction factor. Model results showed that for alfalfa stem densities ranging from 0 to 10 stems/cm2, bank FS ranged from 0.60 to 1.87 and from 0.60 to 1.12 for 1.25 cm and 3.75 cm-high banks respectively. Preliminary results of the laboratory experiments have successfully shown that if cohesion due to roots calculated from the RipRoot model is scaled appropriately, the stability of experimental channels lined with alfalfa of different densities can be predicted. By quantifying the geotechnical resistance of banks during such studies, more accurate predictions of the conditions necessary to create meandering versus braided channel planforms, and the feedback between channel planform and vegetation density in both experimental and real-world scenarios may now be possible.

Structuring of composite hydrogel bioadhesives and its effect on properties and bonding mechanism.

PubMed

Pinkas, Oded; Goder, Daniella; Noyvirt, Roni; Peleg, Sivan; Kahlon, Maayan; Zilberman, Meital

2017-03-15

Bioadhesives are polymeric hydrogels that can adhere to a tissue after crosslinking and are an essential element in nearly all surgeries worldwide. Several bioadhesives are commercially available. However, none of them are ideal. The main limitation of current tissue adhesives is the tradeoff between biocompatibility and mechanical strength, especially in wet hemorrhagic environments. Our novel bioadhesives are based on the natural polymers gelatin (coldwater fish) and alginate, crosslinked by carbodiimide (EDC). Two types of hemostatic agents with a layered silicate structure, montmorillonite (MMT) and kaolin, were loaded in order to improve the sealing ability in a hemorrhagic environment. The effect of the adhesive's components on its mechanical strength was studied by three different methods - burst strength, lap shear and compression. The viscosity, gelation time and structural features of the adhesive were also studied. A qualitative model that describes the effect of the bioadhesive's parameters on the cohesive and adhesive strength was developed. A formulation based on 400mg/mL gelatin, 10mg/mL alginate and 20mg/mL EDC was found as optimal, enabling a burst strength of 387mmHg. Incorporation of kaolin increased the burst strength by 25% due to microcomposite structuring, whereas MMT increased the burst strength by 50% although loaded in a smaller concentration, due to nano-structuring effects. This research clearly shows that the incorporation of kaolin and MMT in gelatin-alginate surgical sealants is a very promising novel approach for improving the bonding strength and physical properties of surgical sealants for use in hemorrhagic environments. The current manuscript focuses on novel bioadhesives, based on natural polymers and loaded with hemostatic agents with a layered silicate structure, in order to improve the sealing ability in hemorrhagic environment. Such composite bioadhesives have not been developed and studied before. The effect of the adhesive's components on its mechanical strength was studied by three different methods, as well as the physical properties and structural features. Thorough understanding of these unique biomaterials resulted in a qualitative model which describes the effect of the bioadhesive's parameters on the cohesive and adhesive strength. Thus, structure-property-function relationships are presented. Structuring of the composite bioadhesives and its effect of the properties and bonding mechanism, are expected to be of high interest to Acta readership. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Effect of Different Peat Size and Pre-Consolidation Pressure of Reconstituted Peat on Effective Undrained Shear Strength Properties

NASA Astrophysics Data System (ADS)

Azhar, ATS; Norhaliza, W.; Ismail, B.; Ezree, AM; Nizam, ZM

2017-08-01

Shear strength of the soil is one of the most important parameters in engineering design, especially during the pre- or post-construction periods, since it is mainly used to measure and evaluate the foundation or slope stability of soil. Peat normally known as a soil that has a very low value of shear strength, and in order to determine and understand the shear strength of the peat, it is a difficult task in geotechnical engineering due to several factors such as types of fabrics, the origin of the soil, water content, organic matter and the degree of humification. The aim of this study is to determine the effective undrained shear strength properties of reconstituted peat of different sizes. All the reconstituted peat samples were formed with the size that passed the opening sieve of 0.425 mm (

Slow Growth of a Crack with Contacting Faces in a Viscoelastic Body

NASA Astrophysics Data System (ADS)

Selivanov, M. F.

2017-11-01

An algorithm for solving the problem of slow growth of a mode I crack with a zone of partial contact of the faces is proposed. The algorithm is based on a crack model with a cohesive zone, an iterative method of finding a solution for the elastic opening displacement, and elasto-viscoelastic analogy, which makes it possible to describe the time-dependent opening displacement in Boltzmann-Volterra form. A deformation criterion with a constant critical opening displacement and cohesive strength during quasistatic crack growth is used. The algorithm was numerically illustrated for tensile loading at infinity and two concentrated forces symmetric about the crack line that cause the crack faces to contact. When the crack propagates, the contact zone disappears and its dynamic growth begins.

Study of the physical properties of Ge-S-Ga glassy alloy

NASA Astrophysics Data System (ADS)

Rana, Anjli; Sharma, Raman

2018-05-01

In the present work, we have studied the effect of Ga doping on the physical properties of Ge20S80-xGax glassy alloy. The basic physical parameters which have important role in determining the structure and strength of the material viz. average coordination number, lone-pair electrons, mean bond energy, glass transition temperature, electro negativity, probabilities for bond distribution and cohesive energy have been computed theoretically for Ge-S-Ga glassy alloy. Here, the glass transition temperature and mean bond energy have been investigated using the Tichy-Ticha approach. The cohesive energy has been calculated by using chemical bond approach (CBA) method. It has been found that while average coordination number increases, all the other parameters decrease with the increase in Ga content in Ge-S-Ga system.

Adhesive Characterization and Progressive Damage Analysis of Bonded Composite Joints

NASA Technical Reports Server (NTRS)

Girolamo, Donato; Davila, Carlos G.; Leone, Frank A.; Lin, Shih-Yung

2014-01-01

The results of an experimental/numerical campaign aimed to develop progressive damage analysis (PDA) tools for predicting the strength of a composite bonded joint under tensile loads are presented. The PDA is based on continuum damage mechanics (CDM) to account for intralaminar damage, and cohesive laws to account for interlaminar and adhesive damage. The adhesive response is characterized using standard fracture specimens and digital image correlation (DIC). The displacement fields measured by DIC are used to calculate the J-integrals, from which the associated cohesive laws of the structural adhesive can be derived. A finite element model of a sandwich conventional splice joint (CSJ) under tensile loads was developed. The simulations indicate that the model is capable of predicting the interactions of damage modes that lead to the failure of the joint.

Mechanics aspects of NDE by sound and ultrasound

NASA Technical Reports Server (NTRS)

Fu, L. S.

1982-01-01

Nondestructive evaluation (NDE) is considered as a means to detect the energy release mechanism of defects and the interaction of microstructures within materials with sound waves and/or ultrasonic waves. Ultrasonic inspection involves the frequency range 20 kHz-1 GHz with amplitudes depending on the sensitivity of the test instrumentation. Pulse echo systems are most frequently used in NDE. Information is extracted from the signals through measurements of the signal velocity, attenuation, the acoustic emission when stress is applied, and calculation of the acoustoelastic coefficients. Fracture properties, tensile and shear strengths, the interlaminar shear strength, the cohesive strength, yield and impact strengths, the hardness, and the residual stress can be assayed by ultrasonic methods. Finally, attention is given to analytical treatment of the derived data, with mention given to transition matrix, integral equation, and eigenstrain approaches.

Internal friction and nonequilibrium unfolding of polymeric globules.

PubMed

Alexander-Katz, Alfredo; Wada, Hirofumi; Netz, Roland R

2009-07-10

The stretching response of a single collapsed homopolymer is studied using Brownian dynamic simulations. The irreversibly dissipated work is found to be dominated by internal friction effects below the collapse temperature, and the internal viscosity grows exponentially with the effective cohesive strength between monomers. These results explain friction effects of globular DNA and are relevant for dissipation at intermediate stages of protein folding.

Robust antireflection coatings By UV cross-linking of silica nanoparticles and diazo-resin polycation

NASA Astrophysics Data System (ADS)

Ridley, Jason I.; Heflin, James R.; Ritter, Alfred L.

2007-09-01

Antireflection coatings have been fabricated by self-assembly using silica nanoparticles. The ionic self-assembled multilayer (ISAM) films are tightly packed and homogeneous. While the geometric properties of a matrix of spherical particles with corresponding void interstices are highly suitable to meet the conditions for minimal reflectivity, it is also a cause for the lack of cohesion within the constituent body, as well as to the substrate surface. This study investigates methods for improving the interconnectivity of the nanoparticle structure. One such method involves UV curing of diazo-resin (DAR)/silica nanoparticle films, thereby converting the ionic interaction into a stronger covalent bond. Factorial analysis and response surface methods are incorporated to determine factors that affect film properties, and to optimize their optical and adhesive capabilities. The second study looks at the adhesive strength of composite multilayer films. Films are fabricated with silica nanoparticles and poly(allylamine hydrochloride) (PAH), and dipped into aqueous solutions of PAH and poly(methacrylic acid, sodium salt) (PMA) to improve cohesion of silica nanoparticles in the matrix, as well as binding strength to the substrate surface. The results of the two studies are discussed.

The role of SEA in integrating and balancing high policy objectives in European cohesion funding programmes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiricka, Alexandra, E-mail: alexandra.jiricka@boku.ac.at; Proebstl, Ulrike, E-mail: ulrike.proebstl@boku.ac.at

Funding programmes for European cohesion policy are a crucial tool to support the sustainability goals of the European Union and national policies of its member states. All these funding programmes require a Strategic Environmental Assessment (SEA) to enhance sustainable development. This article compares five first SEA applications at cohesion policy level to discuss challenges, limitations and benefits of this instrument. In order to support the SEA-process a 'Handbook on SEA for Cohesion Policy 2007-13' (GRDP 2006) was developed. The paper examines the special requirements and challenges at the programme level given the special conditions for stakeholder involvement, integration of SEAmore » in the programme development process and strategies to cope with uncertainties to ensure real compatibility with policy goals. Using action research and in-depth interviews with SEA planners and programme managers enabled us to analyse the suitability of the methodology proposed by the handbook. The results show that some recommendations of the handbook should be changed in order to increase the transparency and to enhance the standard and comparability of the SEA-documents. Overall the SEA proved to be a rather successful tool for the integration of sustainability goals at the EU and national policy levels. Its particular strengths emerged as the process makes uncertainties visible and leads to possible redefinitions while maintaining actual policy goals. - Highlights: Black-Right-Pointing-Pointer Comparing five case studies of first applications of SEA at cohesion policy level. Black-Right-Pointing-Pointer Overall the SEA proved to be a rather successful tool for the integration of sustainability goals. Black-Right-Pointing-Pointer The study makes uncertainties visible and shows how SEA could lead to possible redefinitions.« less

Perceived Family Cohesion Moderates Environmental Influences on Prosocial Behavior in Nigerian Adolescent Twins.

PubMed

Hur, Yoon-Mi; Taylor, Jeanette; Jeong, Hoe-Uk; Park, Min-Seo; Haberstick, Brett C

2017-06-01

Research shows that perceived family cohesion is positively related to prosocial behavior in adolescents. In this study, we investigated heritability of prosocial behavior (PB) and perceived family cohesion (FC) among Nigerian twins attending public schools in Lagos State, Nigeria (mean age = 14.7 years, SD = 1.7 years), and explored the issue of whether children's perception of cohesive family environment moderated genetic and environmental influences on (PB). The PB scale of the Strengths and Difficulties Questionnaire and the FC scale of the Family Adaptability and Cohesion Evaluation Scale III were completed by 2,376 twins (241 monozygotic (MZ) male, 354 MZ female, 440 dizygotic (DZ) male, 553 DZ female, and 788 opposite-sex DZ twins). A general sex-limitation and the bivariate genotype by environment interaction (G×E) models were applied to the data. The general sex-limitation model showed no significant sex differences, indicating that additive genetic and non-shared environmental influences were, 38% (95% CI = 31, 46) and 62% (95% CI = 54, 69) for PB and 33% (95% CI = 24, 40) and 67% (95% CI = 60, 76) for FC in both sexes. These estimates were similar to those found in Western and Asian twin studies to date. The correlation between PB and FC was 0.36. The best-fitting bivariate G×E model indicated that FC significantly moderated non-shared environmental influence unique to PB (E×E interaction). Specifically, non-shared environmental contributions to PB were highest when FC was lowest, and decreased as the levels of FC increased. However, genetic variances in PB were stable across all levels of FC. These findings suggest that FC reduces individual differences in PB by changing non-shared environmental experiences rather than genetic factors in PB.

Root strength of tropical plants - An investigation in the Western Ghats of Kerala, India

NASA Astrophysics Data System (ADS)

Lukose Kuriakose, S.; van Beek, L. P. H.; van Westen, C. J.

2009-04-01

Earlier research on debris flows in the Tikovil River basin of the Western Ghats concluded that root cohesion is significant in maintaining the overall stability of the region. In this paper we present the most recent results (December 2008) of root tensile strength tests conducted on nine species of plants that are commonly found in the region. They are 1) Rubber (Hevea Brasiliensis), 2) Coconut Palm (Cocos nucifera), 3) Jackfruit trees (Artocarpus heterophyllus), 4) Teak (Tectona grandis), 5) Mango trees (Mangifera indica), 6) Lemon grass (Cymbopogon citratus), 7) A variety of Tamarind (Garcinia gummigutta), 8) Coffee (Coffea Arabica) and Tea (Camellia sinensis). About 1500 samples were collected of which only 380 could be tested (in the laboratory) due to breakage of roots during the tests. In the successful tests roots failed in tension. Roots having diameters between 2 mm and 12 mm were tested. Each sample tested has a length of 15 cm. Results indicate that the roots of Coffee, Tamarind, Lemon grass and Jackfruit are the strongest of the nine plant types tested whereas Tea and Teak plants had the most fragile roots. Coconut roots behaved atypical to the others, as the bark of the roots was crushed and slipped from the clamp when tested whereas its internal fiber was the strongest of all tested. Root tensile strength decreases with increasing diameters, Rubber showing more ductile behaviour than Coffee and Tamarind that behaved more brittle, root tensile strength increasing exponentially for finer roots. Teak and Tea showed almost a constant root tensile strength over the range of diameters tested and little variability. Jack fruit and mango trees showed the largest variability, which may be explained by the presence of root nodules, preventing the derivation of an unequivocal relationship between root diameters and tensile strength. This results in uncertainty of root strength estimates that are applicable. These results provide important information to quantify the upper limit of the root cohesion at the stand level in combination with land use maps. This is an indispensable component in the evaluation of slope stability in the region.

Numerical modelling of collapsing volcanic edifices

NASA Astrophysics Data System (ADS)

Costa, Ana; Marques, Fernando; Kaus, Boris

2017-04-01

The flanks of Oceanic Volcanic Edifice's (OVEs) can occasionally become unstable. If that occurs, they can deform in two different modes: either slowly along localization failure zones (slumps) or catastrophically as debris avalanches. Yet the physics of this process is incompletely understood, and the role of factors such as the OVE's strength (viscosity, cohesion, friction angle), dimensions, geometry, and existence of weak layers remain to be addressed. Here we perform numerical simulations to study the interplay between viscous and plastic deformation on the gravitational collapse of an OVE (diffuse deformation vs. localization of failure along discrete structures). We focus on the contribution of the edifice's strength parameters for the mode of deformation, as well as on the type of basement. Tests were performed for a large OVE (7.5 km high, 200 km long) and either purely viscous (overall volcano edifice viscosities between 1019-1023 Pa.s), or viscoplastic rheology (within a range of cohesion and friction angle values). Results show that (a) for a strong basement (no slip basal boundary condition), the deformation pattern suggests wide/diffuse "listric" deformation within the volcanic edifice, without the development of discrete plastic failure zones; (b) for a weak basement (free slip basal boundary condition), rapid collapse of the edifice through the propagation of plastic failure structures within the edifice occurs. Tests for a smaller OVE (4.5 km by 30 km) show that failure localization along large-scale listric structures occurs more readily for different combinations of cohesion and friction angles. In these tests, high cohesion values combined with small friction angles lead to focusing of deformation along a narrower band. Tests with a weak layer underlying part of the volcanic edifice base show deformation focused along discrete structures mainly dipping towards the distal sector of the volcano. These tests for a small OVE constitute a promising basis for the study of a currently active slump in the SE flank of Pico Island (Azores, Portugal). We will also address the effect of lithospheric flexure, and discuss initial 3D modelling results.

Surface modification for enhanced silanation of zirconia ceramics.

PubMed

Piascik, J R; Swift, E J; Thompson, J Y; Grego, S; Stoner, B R

2009-09-01

The overall goal of this research was to develop a practical method to chemically modify the surface of high strength dental ceramics (i.e. zirconia) to facilitate viable, robust adhesive bonding using commercially available silanes and resin cements. Investigation focused on a novel approach to surface functionalize zirconia with a Si(x)O(y) "seed" layer that would promote chemical bonding with traditional silanes. ProCAD and ZirCAD blocks were bonded to a dimensionally similar composite block using standard techniques designed for silica-containing materials (silane and resin cement). ZirCAD blocks were treated with SiCl4 by vapor deposition under two different conditions prior to bonding. Microtensile bars were prepared and subjected to tensile forces at a crosshead speed of 1 mm/min scanning electron microscopy was used to analyze fracture surfaces and determine failure mode; either composite cohesive failure (partial or complete cohesive failure within composite) or adhesive failure (partial or complete adhesive failure). Peak stress values were analyzed using single-factor ANOVA (p<0.05). Microtensile testing results revealed that zirconia with a surface treatment of 2.6 nm Si(x)O(y) thick "seed" layer was similar in strength to the porcelain group (control). Analysis of failure modes indicated the above groups displayed higher percentages of in-composite failures. Other groups tested had lower strength values and displayed adhesive failure characteristics. Mechanical data support that utilizing a gas-phase chloro-silane pretreatment to deposit ultra-thin silica-like seed layers can improve adhesion to zirconia using traditional silanation and bonding techniques. This technology could have clinical impact on how high strength dental materials are used today.

The Dynamics of Interacting Swarms

DTIC Science & Technology

2018-04-04

Unlimited 16 Ira Schwartzt (202) 404-8359 Swarms are self-organized dynamical coupled agents which evolve from simple rules of communication. They are ...when delay is introduced to the communicating agents. One of our major findings is that interacting swarms are far less likely to flock cohesively if...they are coupled with delay. In addition, parameter ranges based on coupling strength, incidence angle of collision, and delay change dramatically

Impact and Penetration Problems.

DTIC Science & Technology

1981-03-16

constant is now determined theoretically. iii) By utilizing the formal similarity between the two criteria (1) and (3), we can predict the theoretical...cohesive strengths of various crystals. Once the experimental value for y is given, the calculations can be carried 4 out easily to determine the...analytical solution to the mixed boundary value problem yields the nonlocal displacement and stress fields. The nonlocal parameter c is determined by

Regolith on Super Fast Rotators

NASA Astrophysics Data System (ADS)

Sanchez Lana, Diego Paul; Scheeres, Daniel J.

2017-10-01

The current understanding of small asteroids in the Solar System is that they are gravitational aggregates held together by gravitational, cohesive and adhesive forces. Results from the Hayabusa mission to Itokawa along with in situ, thermal and radar observations of asteroids have shown that they can be covered in a size distribution of grains that spans from microns to tens of meters. Before the Hayabusa mission, it was generally thought that smaller asteroids would likely be “regolith-free,” due to impact seismic shaking removing the loose covering. Given the regolith-rich surface of that body, it is now an open question whether even smaller bodies, down to a few meters in size, could also retain regolith covering. The question is especially compelling for the small-fast rotators, whose surface centripetal accelerations exceed their gravitational attraction. When the physical theory of cohesion is considered, it becomes possible for small-fast rotators to retain regolith.We use a Soft-Sphere discrete element method (SSDEM) code to simulate a longitudinal slice of a spherical monolith covered by cohesive regolith. The simulations are carried out in the body frame. Tensile strength is varied to span the observed strength of asteroids and spin rate is elevated in small steps until the majority of regolith is removed from the surface. The simulations show that under an increasing spin rate (such as due to the YORP effect), the regolith covering on an otherwise monolithic asteroid is preferentially lost across certain regions of the body. In general, regolith from the mid latitudes is the first to fail at high spin rates. This failure happens either by regolith flowing towards the equator or by detachment of large coherent chunks of material depending on the tensile strength of the regolith. Regolith from the equator region fails next, usually by the detachment of large pieces. Regolith from the poles stays in place unless the spin rates are extremely high. With these results we derive a scaling law that can be used to determine whether observed small asteroids could retain surface regolith of a given size. The implications of this for the interpretation of spectral observations of small asteroids are discussed.

Hysteresis heating based induction bonding of composite materials

NASA Astrophysics Data System (ADS)

Suwanwatana, Witchuda

The viability of using magnetic particulate susceptor materials for induction heating during bonding of polymer matrix composites is well established in this work. The unique ability to offer localized heating, geometric flexibility, and self-controlled temperature is the major advantage of this technique. Hysteresis heating is tailored through careful design of the microstructure of nickel particulate polymer films (Ni/PSU). An excellent heating rate can be attained in the frequency range of 1 to 10 MHz for particle volume fraction below percolation of 0.26. The diameter of nickel particle should be kept between 65 nm to 10 mum to ensure multi-domain heating, Curie temperature control, negligible shielding effect, minimum eddy current, and slight particle oxidation. The hysteresis heating behavior of the Ni/PSU films is found to be volumetric in nature and proportional to the cube of applied magnetic field. On the other hand, heat generation is inversely proportional to the size of the multi-domain particles. The frequency effect; however, provide maximum heat generation at the domain wall resonance frequency. Curie temperature control is observed when sufficiently high magnetic fields (˜138 Oe) are applied. The master curves of AC heat generation in Ni/PSU films are established and show a strong particle size effect. Hysteresis fusion bonding of glass/polyphenylene sulfide thermoplastic composites using a magnetic film as the thermoplastic adhesive shows that the bond strength of hysteresis-welded materials is comparable to that of autoclave-welded materials while offering an order of magnitude reduction in cycle time. The relative contribution of the intimate contact and healing mechanisms to the fusion bonding process indicates that hysteresis bonding is controlled by intimate contact. The macroscopic failure modes vary from mostly adhesive composite/film (low bond strength) to a combination of adhesive composite/film, cohesive film, cohesive composite and mostly cohesive composite (high bond strength). Inspection of the microscopic failure at the nickel particle/polymer interface in the film indicates quasi-brittle failure mode. The amount of adhesive failure increases with decreasing particle size and increasing particle volume fraction. The XPS peaks confirm nickel oxide in the form of NiO on the failure surface of particle/polymer debonding of hysteresis susceptor film.

Bonded-cell model for particle fracture.

PubMed

Nguyen, Duc-Hanh; Azéma, Emilien; Sornay, Philippe; Radjai, Farhang

2015-02-01

Particle degradation and fracture play an important role in natural granular flows and in many applications of granular materials. We analyze the fracture properties of two-dimensional disklike particles modeled as aggregates of rigid cells bonded along their sides by a cohesive Mohr-Coulomb law and simulated by the contact dynamics method. We show that the compressive strength scales with tensile strength between cells but depends also on the friction coefficient and a parameter describing cell shape distribution. The statistical scatter of compressive strength is well described by the Weibull distribution function with a shape parameter varying from 6 to 10 depending on cell shape distribution. We show that this distribution may be understood in terms of percolating critical intercellular contacts. We propose a random-walk model of critical contacts that leads to particle size dependence of the compressive strength in good agreement with our simulation data.

Thermoplastic matrix composite processing model

NASA Technical Reports Server (NTRS)

Dara, P. H.; Loos, A. C.

1985-01-01

The effects the processing parameters pressure, temperature, and time have on the quality of continuous graphite fiber reinforced thermoplastic matrix composites were quantitatively accessed by defining the extent to which intimate contact and bond formation has occurred at successive ply interfaces. Two models are presented predicting the extents to which the ply interfaces have achieved intimate contact and cohesive strength. The models are based on experimental observation of compression molded laminates and neat resin conditions, respectively. Identified as the mechanism explaining the phenomenon by which the plies bond to themselves is the theory of autohesion (or self diffusion). Theoretical predictions from the Reptation Theory between autohesive strength and contact time are used to explain the effects of the processing parameters on the observed experimental strengths. The application of a time-temperature relationship for autohesive strength predictions is evaluated. A viscoelastic compression molding model of a tow was developed to explain the phenomenon by which the prepreg ply interfaces develop intimate contact.

Superposition of Cohesive Elements to Account for R-Curve Toughening in the Fracture of Composites

NASA Technical Reports Server (NTRS)

Davila, Carlos G.; Rose, Cheryl A.; Song, Kyongchan

2008-01-01

The relationships between a resistance curve (R-curve), the corresponding fracture process zone length, the shape of the traction/displacement softening law, and the propagation of fracture are examined in the context of the through-the-thickness fracture of composite laminates. A procedure that accounts for R-curve toughening mechanisms by superposing bilinear cohesive elements is proposed. Simple equations are developed for determining the separation of the critical energy release rates and the strengths that define the independent contributions of each bilinear softening law in the superposition. It is shown that the R-curve measured with a Compact Tension specimen test can be reproduced by superposing two bilinear softening laws. It is also shown that an accurate representation of the R-curve is essential for predicting the initiation and propagation of fracture in composite laminates.

Cohesive Modeling of Transverse Cracking in Laminates with a Single Layer of Elements per Ply

NASA Technical Reports Server (NTRS)

VanDerMeer, Frans P.; Davila, Carlos G.

2013-01-01

This study aims to bridge the gap between classical understanding of transverse cracking in cross-ply laminates and recent computational methods for the modeling of progressive laminate failure. Specifically, the study investigates under what conditions a finite element model with cohesive X-FEM cracks can reproduce the in situ effect for the ply strength. It is shown that it is possible to do so with a single element across the thickness of the ply, provided that the interface stiffness is properly selected. The optimal value for this interface stiffness is derived with an analytical shear lag model. It is also shown that, when the appropriate statistical variation of properties has been applied, models with a single element through the thickness of a ply can predict the density of transverse matrix cracks

Influence of exposure time to saliva and antioxidant treatment on bond strength to enamel after tooth bleaching: an in situ study

PubMed Central

MIRANDA, Thais Aglaet Matos; MOURA, Sandra Kiss; AMORIM, Vitor Hugo de Oliveira; TERADA, Raquel Sano Suga; PASCOTTO, Renata Corrêa

2013-01-01

Objectives This study evaluated the influence of different exposure times to saliva in situ in comparison with an antioxidant treatment on composite resin bond strength to human enamel restored after tooth bleaching. Material and Methods Forty human teeth specimens measuring 5x5 mm were prepared and randomly allocated into 5 groups with 8 specimens each: Gct (control group, restored on unbleached enamel); Gbl (restored immediately after bleaching); Gsa (bleached, treated with 10% sodium ascorbate gel for 60 min and restored); G7d (bleached, exposed to saliva in situ for 7 days and restored); and G14d (bleached, exposed to saliva in situ for 14 days and restored). Restored samples were cut into 0.8 mm2 sticks that were tested in microtensile. Specimens were microscopically analyzed and failure modes were classified as adhesive, cohesive, or mixed. Pretest and cohesive failures were not considered in the statistical analysis, which was performed with one-way ANOVA and Tukey's post-hoc test (α=0.05), with the dental specimen considered as the experimental unit. Results Mean bond strength results found for Gbl in comparison with Gct indicated that bleaching significantly reduced enamel adhesiveness (P<0.01). However, no statistically significant differences were found between Gct, Gsa and G7d (P>0.05). Bond strength found for G14d was significantly higher than for Gsa (P<0.01). Fractures modes were predominantly of a mixed type. Conclusions Bonding strength to bleached enamel was immediately restored with the application of sodium ascorbate and exposure to human saliva in situ for at least 7 days. Best results were obtained with exposure to human saliva in situ for 14 days. Treatment with sodium ascorbate gel for 60 min may be recommended in cases patients cannot wait for at least 7 days for adhesive techniques to be performed. PMID:24473724

Geometry of the Nojima fault at Nojima-Hirabayashi, Japan - II. Microstructures and their implications for permeability and strength

USGS Publications Warehouse

Moore, Diane E.; Lockner, D.A.; Ito, H.; Ikeda, R.; Tanaka, H.; Omura, K.

2009-01-01

Samples of damage-zone granodiorite and fault core from two drillholes into the active, strike-slip Nojima fault zone display microstructures and alteration features that explain their measured present-day strengths and permeabilities and provide insight on the evolution of these properties in the fault zone. The least deformed damage-zone rocks contain two sets of nearly perpendicular (60-90?? angles), roughly vertical fractures that are concentrated in quartz-rich areas, with one set typically dominating over the other. With increasing intensity of deformation, which corresponds generally to increasing proximity to the core, zones of heavily fragmented rock, termed microbreccia zones, develop between prominent fractures of both sets. Granodiorite adjoining intersecting microbreccia zones in the active fault strands has been repeatedly fractured and locally brecciated, accompanied by the generation of millimeter-scale voids that are partly filled with secondary minerals. Minor shear bands overprint some of the heavily deformed areas, and small-scale shear zones form from the pairing of closely spaced shear bands. Strength and permeability measurements were made on core collected from the fault within a year after a major (Kobe) earthquake. Measured strengths of the samples decrease regularly with increasing fracturing and fragmentation, such that the gouge of the fault core and completely brecciated samples from the damage zone are the weakest. Permeability increases with increasing disruption, generally reaching a peak in heavily fractured but still more or less cohesive rock at the scale of the laboratory samples. Complete loss of cohesion, as in the gouge or the interiors of large microbreccia zones, is accompanied by a reduction of permeability by 1-2 orders of magnitude below the peak values. The core samples show abundant evidence of hydrothermal alteration and mineral precipitation. Permeability is thus expected to decrease and strength to increase somewhat in active fault strands between earthquakes, as mineral deposits progressively seal fractures and fill pore spaces. ?? Birkh??user Verlag, Basel 2009.

Posttraumatic Stress, Family Functioning, and Externalizing in Adolescents Exposed to Violence: A Moderated Mediation Model.

PubMed

Deane, Kyle; Richards, Maryse; Mozley, Michaela; Scott, Darrick; Rice, Catherine; Garbarino, James

2016-09-02

Exposure to community violence disproportionately impacts low-income, minority youth and is associated with posttraumatic stress symptoms and maladaptive adjustment. This study investigates whether posttraumatic stress mediates the relation between exposure to community violence and externalizing symptoms and the moderating role of family cohesion and daily family support in buffering these effects on later externalizing. Low-income, African American 7th-grade students (M age = 12.57 years; N = 254) from high-crime neighborhoods participated in a 2-year longitudinal study measuring the effects of community violence exposure. The students completed questionnaires administered by research staff over 5 consecutive days for each year of the study. Family cohesion and daily family support exhibited a significant buffering effect for several outcomes. Posttraumatic stress significantly mediated the effect of witnessing community violence on subsequent aggression. The strength of these indirect effects depended on level of family cohesion. The findings provide evidence in support of interventions provided at both individual and family levels. Mental health providers working with this population should be aware of the intertwined nature of exposure to community violence, posttraumatic stress, and subsequent maladaptive outcomes.

Cohesive forces prevent the rotational breakup of rubble-pile asteroid (29075) 1950 DA.

PubMed

Rozitis, Ben; MacLennan, Eric; Emery, Joshua P

2014-08-14

Space missions and ground-based observations have shown that some asteroids are loose collections of rubble rather than solid bodies. The physical behaviour of such 'rubble-pile' asteroids has been traditionally described using only gravitational and frictional forces within a granular material. Cohesive forces in the form of small van der Waals forces between constituent grains have recently been predicted to be important for small rubble piles (ten kilometres across or less), and could potentially explain fast rotation rates in the small-asteroid population. The strongest evidence so far has come from an analysis of the rotational breakup of the main-belt comet P/2013 R3 (ref. 7), although that was indirect and poorly constrained by observations. Here we report that the kilometre-sized asteroid (29075) 1950 DA (ref. 8) is a rubble pile that is rotating faster than is allowed by gravity and friction. We find that cohesive forces are required to prevent surface mass shedding and structural failure, and that the strengths of the forces are comparable to, though somewhat less than, the forces found between the grains of lunar regolith.

Key Barriers to Community Cohesion: Views from Residents of 20 London Deprived Neighbourhoods

PubMed Central

Bertotti, Marcello; Adams-Eaton, Faye; Sheridan, Kevin; Renton, Adrian

2016-01-01

The notion of community has been central to the political project of renewal of New Labour in the UK. The paper explores how the discourses of community are framed within New Labour and discusses these in the light of the results from research which focuses on how people within urban deprived areas construct their community. It draws upon the results of one part of a larger research project (the ‘Well London’ programme) which aimed to capture the views of residents from 20 disadvantaged neighbourhoods throughout London using an innovative qualitative method known as the ‘World Café’. Our results show the centrality of young people to the development of cohesive communities, the importance of building informal relationships between residents alongside encouraging greater participation to policy making, and the need to see these places as fragile and temporary locations but with considerable social strengths. Government policies are only partially addressing these issues. They pay greater attention to formally encouraging citizens to become more involved in policy making, largely ignore the contribution young people could make to the community cohesion agenda, and weakly define the shared norms and values that are crucial in building cohesive communities. Thus, the conclusion is that whilst an emphasis of the government on ‘community’ is to be welcome, more needs to be done in terms of considering the ‘voices’ of the community as well as enabling communities to determine and act upon their priorities. PMID:27761059

Verification of surface preparation for adhesive bonding

NASA Technical Reports Server (NTRS)

Myers, Rodney S.

1995-01-01

A survey of solid rocket booster (SRB) production operations identified potential contaminants which might adversely affect bonding operations. Lap shear tests quantified these contaminants' effects on adhesive strength. The most potent contaminants were selected for additional studies on SRB thermal protection system (TPS) bonding processes. Test panels were prepared with predetermined levels of contamination, visually inspected using white and black light, then bonded with three different TPS materials over the unremoved contamination. Bond test data showed that white and black light inspections are adequate inspection methods for TPS bonding operations. Extreme levels of contamination (higher than expected on flight hardware) had an insignificant effect on TPS bond strengths because of the apparent insensitivity of the adhesive system to contamination effects, and the comparatively weak cohesive strength of the TPS materials.

Application of Bionic Design to FRP T-Joints

NASA Astrophysics Data System (ADS)

Luo, Guang-Min; Kuo, Chia-Hung

2017-09-01

We applied the concepts of bionics to enhance the mechanical strength of fiberglass reinforced plastic T-joints. The failure modes of the designed arthrosis-like and gum-like joints were determined using three-point bending tests and numerical simulations and compared with those of normal T-joints bonded using structural adhesives. In the simulation, we used cohesive elements to simulate the adhesive interface of the structural adhesive. The experimental and simulation results show that the arthrosis-like joint can effectively delay the failure progress and enhance the bonding strength of T-joints, thus confirming that an appropriate bionic design can effectively control the bonding properties of structural adhesives.

Terrace width variations in complex Mercurian craters and the transient strength of cratered Mercurian and lunar crust

NASA Technical Reports Server (NTRS)

Leith, Andrew C.; Mckinnon, William B.

1991-01-01

The effective cohesion of the cratered region during crater collapse is determined via the widths of slump terraces of complex craters. Terrace widths are measured for complex craters on Mercury; these generally increase outward toward the rim for a given crater, and the width of the outermost major terrace is generally an increasing function of crater diameter. The terrace widths on Mercury and a gravity-driven slump model are used to estimate the strength of the cratered region immediately after impact (about 1-2 MPa). A comparison with the previous study of lunar complex craters by Pearce and Melosh (1986) indicates that the transient strength of cratered Mercurian crust is no greater than that of the moon. The strength estimates vary only slightly with the geometric model used to restore the outermost major terrace to its precollapse configuration and are consistent with independent strength estimates from the simple-to-complex crater depth/diameter transition.

Human Factors and Information Security: Individual, Culture and Security Environment

DTIC Science & Technology

2010-10-01

cannot operate effectively ( Ivancevich et al., 2000). However, Buono, Bowditch and Lewis (1985), state that the strength of values is questionable...socialisation can be viewed as a form of organisational integration ( Ivancevich et al., 2000). Specifically, socialisation “is a strategy for achieving... Ivancevich et al., 2000, p.605). Organisations with strong cultures are considered to operate under a cohesive set of values and norms (George & Jones

Computer Modeling of the Cooking Process for Pizza

DTIC Science & Technology

1991-08-01

on the structure. They are the proteins that form gluten and are responsible for the strength, elasticity, and cohesion properties of the dough...It is impossible to make dough without using water. It makes the formation of gluten possible. It creates a dispersion of the other ingredients and...interior of bread products), and improve volume (Pomeranz, 1987). Once all the ingredients have been assembled they are mixed. Glutens are formed

Ductilization of High-Strength Magnesium Alloys

DTIC Science & Technology

2012-09-17

ductility in this system. Figure 4 compares true stress strain curves measured for the solution-treated and peak-aged conditions. Fractography of the...plane 1.274 1.094 1.213 Figure 4. Measured true stress-strain curves and fractography of WE43 Mg alloy Figure 3. FLAPW...Therefore, the enhancement of grain boundary cohesion plays an important role in the improvement of ductility. Figure 5 Fractography of WE43 at

The modelling influence of water content to mechanical parameter of soil in analysis of slope stability

NASA Astrophysics Data System (ADS)

Gusman, M.; Nazki, A.; Putra, R. R.

2018-04-01

One of the parameters in slope stability analysis is the shear strength of the soil. Changes in soil shear strength characteristics lead to a decrease in safety factors on the slopes. This study aims to see the effect of increased moisture content on soil mechanical parameters. The case study study was conducted on the slopes of Sitinjau Lauik Kota Padang. The research method was done by laboratory analysis and simple liniear regression analysis and multiple. Based on the test soil results show that the increase in soil water content causes a decrease in cohesion values and internal shear angle. The relationship of moisture content to cohesion is described in equation Y = 55.713-0,6X with R2 = 0.842. While the relationship of water content to shear angle in soil is described in the equation Y = 38.878-0.258X with R2 = 0.915. From several simulations of soil water level improvement, calculation of safety factor (SF) of slope. The calculation results show that the increase of groundwater content is very significant affect the safety factor (SF) slope. SF slope values are in safe condition when moisture content is 50% and when it reaches maximum water content 73.74% slope safety factor value potentially for landslide.

Effects of some lubricants and evaluation of compression parameters on directly compressible powders.

PubMed

Uğurlu, Timuçin; Halaçoğlu, Mekin Doğa

2014-05-01

The objective of this study was to investigate the effects of conventional lubricants including a new candidate lubricant "Hexagonal boron nitride (HBN)" on direct compression powders. Lubricants such as magnesium stearate, glyceryl behenate, stearic acid, talc and polyethylene glycol6000 were studied in this article. Tablets were manufactured on an instrumented tablet press with various lubricant concentrations. Bulk and tapped densities, and Carr's index parameters were calculated for powders. Tensile strength, cohesion index, lower punch ejection force and lubricant effectiveness values were investigated for tablets. The deformation mechanisms of tablets were studied during compression from the Heckel plots with or without lubricants. Powders formulated with MGST and HBN showed better flow properties based on Carr's index. MGST was found to be the most effective lubricant based on lubricant effectiveness for tablets. HBN was found very close to MGST with the same concentrations. Other lubricants showed less effectiveness than that of MGST and HBN. It is observed that an increase in the concentration of HBN leads to decreased tensile strength and cohesion index values because of its surface-covering property. Despite covering property, HBN had no significant effect on disintegration time. Based on the Heckel plots at the level of 1%, HBN showed the most pronounced plastic character.

Evaluation of critical shear stresses for consolidated cohesive sediment depositions by using PIV compared with field measurements

NASA Astrophysics Data System (ADS)

Harb, Gabriele; Haun, Stefan

2013-04-01

Reservoir sedimentation is a common problem today. Due to the reduced flow velocities, turbulences and bed shear stresses the transported sediment load start to settle. These depositions reduce the worldwide average storage capacity in the range of about 1% per year. However, depending on the climate conditions and the geology in the catchment area this value may vary strongly. Therefore sediment management tasks, especially the removal of already accumulated sediments, have to be developed for each reservoir separately. The critical bed shear stress is a key parameter used to evaluate the different management tasks and depend strongly on the grain size distribution of the inflowing sediments. However, depositions which contain fine particles like clay and silt increase the critical bed shear stress due to occurring cohesive forces and the use of the Shield curve for evaluating the critical shear stress is no longer valid. Additional data is required for estimating the valid critical shear stress at the reservoir bed. In this study the critical shear stress was evaluated for cohesive sediment samples, taken from two different reservoirs, in a flume in the laboratory. The sediment samples were placed in an installed double bottom in the research flume and the discharge was increased stepwise until mass erosion took place (determined by visual inspection). A 2D PIV device was used to measure the flow conditions (velocities and turbulences) over the sediment sample. The obtained values were used to calculate the bed shear stress for the specific discharge rate by the gravity method and the Reynolds stress method. The results of both methods showed good agreement in the comparison of the values, what indicates that nearly uniform flow conditions occurred in the flume. The results from this study showed that the behaviour of natural cohesive sediments depend strongly on the natural conditions as a result of physical, chemical and biological processes. In this case especially the effect of the layer structure in the sediment samples was controlling the erosion mechanism. The results of the experiments showed also that the obtained average shear stress was above most of the values found in previous conducted studies, which may be explained by consolidation effects in the reservoirs. Additional conducted vane strength measurements have been carried out in situ. The in the field obtained vane strength values were set in relation to the critical shear stresses derived by the experimental tests from the laboratory and to data from a previous conducted study to develop a new relation function. This function may be used in future studies for a rough estimation of the critical shear stress, based on in situ measured vane strength values.

The influence and ethics of interest groups on policy incentives for clean energy development

NASA Astrophysics Data System (ADS)

Maguire, Mariana C.

The clean energy revolution in the United States is not going to happen until diverse stakeholders in the coalition of clean energy proponents strengthen their cohesion and influence—two critical tools for interest group's to be successful in driving the formulation of public policy. Currently, clean energy technology and resource development is supported by a highly diverse coalition of interest groups such as environmental groups, health organizations, industry, and the Defense Department, whose primary goals are often unrelated. Yet their objectives are increasingly well served by pursuing clean energy development by pushing lawmakers for supportive policies. However, characteristics of this ad hoc coalition can hinder its influence and cohesion. Whereas, fossil fuel interests—exemplified by the coalition of oil proponents—are highly cohesive and influential. This thesis will analyze whether there is a correlation between public policies on clean energy, and the strength of interest group influence over those policy decisions. It will begin with an analysis of interest group theories. Next it will analyze the histories of the oil industry as the model opponent of clean energy policies, and the biofuels, wind energy, and solar energy industries as the model proponents of clean energy policies. The composition of the respective coalitions will reveal if they are diverse or similar, with broad or narrow goals, and other important characteristics. Their respective policy positions and messages will show what values are important to them, and the presidential support each coalition has been achieved, or failed to achieve, will provide further insight into their effectiveness. This thesis will then apply interest group theories to the supporter and opponent coalitions. Results obtained indicate that the coalition of oil interests is large, yet very cohesive and influential, while the coalition for clean energy is large, generally diffuse but with some important signs of cohesion, and relatively influential. Therefore this analysis concludes that the clean energy coalition must strengthen itself in areas that produce cohesion, such as encouraging partnerships with stakeholders with asymmetrical interests, and increase its financial influence in order to leverage more resources toward influencing policymakers to promote clean energy development.

Adhesion, friction, and wear behavior of clean metal-ceramic couples

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa

1995-01-01

When a clean metal is brought into contact with a clean, harder ceramic in ultrahigh vacuum, strong bonds form between the two materials. The interfacial bond strength between the metal and ceramic surfaces in sliding contact is generally greater than the cohesive bond strength in the metal. Thus, fracture of the cohesive bonds in the metal results when shearing occurs. These strong interfacial bonds and the shearing fracture in the metal are the main causes of the observed wear behavior and the transfer of the metal to the ceramic. In the literature, the surface energy (bond energy) per unit area of the metal is shown to be related to the degree of interfacial bond strength per unit area. Because the two materials of a metal-ceramic couple have markedly different ductilities, contact can cause considerable plastic deformation of the softer metal. It is the ductility of the metal, then, that determines the real area of contact. In general, the less ductile the metal, the smaller the real area of contact. The coefficient of friction for clean surfaces of metal-ceramic couples correlates with the metals total surface energy in the real area of contact gamma A (which is the product of the surface energy per unit area of the metal gamma and the real area of contact (A)). The coefficient of friction increases as gamma A increases. Furthermore, gamma A is associated with the wear and transfer of the metal at the metal-ceramic interface: the higher the value of gamma A, the greater the wear and transfer of the metal.

Mechanical properties of lunar regolith and lunar soil simulant

NASA Technical Reports Server (NTRS)

Perkins, Steven W.

1989-01-01

Through the Surveyor 3 and 7, and Apollo 11-17 missions a knowledge of the mechanical properties of Lunar regolith were gained. These properties, including material cohesion, friction, in-situ density, grain-size distribution and shape, and porosity, were determined by indirect means of trenching, penetration, and vane shear testing. Several of these properties were shown to be significantly different from those of terrestrial soils, such as an interlocking cohesion and tensile strength formed in the absence of moisture and particle cementation. To characterize the strength and deformation properties of Lunar regolith experiments have been conducted on a lunar soil simulant at various initial densities, fabric arrangements, and composition. These experiments included conventional triaxial compression and extension, direct tension, and combined tension-shear. Experiments have been conducted at low levels of effective confining stress. External conditions such as membrane induced confining stresses, end platten friction and material self weight have been shown to have a dramatic effect on the strength properties at low levels of confining stress. The solution has been to treat these external conditions and the specimen as a full-fledged boundary value problem rather than the idealized elemental cube of mechanics. Centrifuge modeling allows for the study of Lunar soil-structure interaction problems. In recent years centrifuge modeling has become an important tool for modeling processes that are dominated by gravity and for verifying analysis procedures and studying deformation and failure modes. Centrifuge modeling is well established for terrestrial enginering and applies equally as well to Lunar engineering. A brief review of the experiments is presented in graphic and outline form.

Diffusion-coupled cohesive interface simulations of stress corrosion intergranular cracking in polycrystalline materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pu, Chao; Gao, Yanfei; Wang, Yanli

To study the stress corrosion intergranular cracking mechanism, a diffusion-coupled cohesive zone model (CZM) is proposed for the simulation of the stress-assisted diffusional process along grain boundaries and the mechanical response of grain boundary sliding and separation. This simulation methodology considers the synergistic effects of impurity diffusion driven by pressure gradient and degradation of grain boundary strength by impurity concentration. The diffusion-coupled CZM is combined with crystal plasticity finite element model (CPFEM) to simulate intergranular fracture of polycrystalline material under corrosive environment. Significant heterogeneity of the stress field and extensive impurity accumulation is observed at grain boundaries and junction points.more » Deformation mechanism maps are constructed with respect to the grain boundary degradation factor and applied strain rate, which dictate the transition from internal to near-surface intergranular fracture modes under various strain amplitudes and grain sizes.« less

The effect of surface and interface on Neel transition temperature of low-dimensional antiferromagnetic materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Wen; Zhou, Zhaofeng, E-mail: zfzhou@xtu.edu.cn; Zhong, Yuan

2015-11-15

Incorporating the bond order-length-strength (BOLS) notion with the Ising premise, we have modeled the size dependence of the Neel transition temperature (T{sub N}) of antiferromagnetic nanomaterials. Reproduction of the size trends reveals that surface atomic undercoordination induces bond contraction, and interfacial hetero-coordination induces bond nature alteration. Both surface and interface of nanomaterials modulate the T{sub N} by adjusting the atomic cohesive energy. The T{sub N} is related to the atomic cohesive/exchange energy that is lowered by the coordination number (CN) imperfection of the undercoordinated atoms near the surface and altered by the changed bond nature of epitaxial interface. A numericalmore » match between predictions and measurements reveals that the T{sub N} of antiferromagnetic nanomaterials declines with reduced size and increases with both the strengthening of heterogeneous bond and the increase of the bond number.« less

Mechanics of fold-and-thrust belts and accretionary wedges Cohesive Coulomb theory

NASA Technical Reports Server (NTRS)

Dahlen, F. A.; Suppe, J.; Davis, D.

1984-01-01

A self-consistent theory for the mechanics of thin-skinned accretionary Coulomb wedges is developed and applied to the active fold-and-thrust belt of western Taiwan. The state of stress everywhere within a critical wedge is determined by solving the static equilibrium equations subject to the appropriate boundary conditions. The influence of wedge cohesion, which gives rise to a concave curvature of the critical topographic surface and affects the orientation of the principal stresses and Coulomb fracture within the wedge, is considered. The shape of the topographic surface and the angles at which thrust faults step up from the basal decollement in the Taiwanese belt is analyzed taking into account the extensive structural and fluid-pressure data available there. It is concluded that the gross geometry and structure of the Taiwan wedge are consistent with normal laboratory frictional and fracture strengths of sedimentary rocks.

Tissue soldering with biodegradable polymer films: in-vitro investigation of hydration effects on weld strength

NASA Astrophysics Data System (ADS)

Sorg, Brian S.; Welch, Ashley J.

2001-05-01

Previous work demonstrated increased breaking strengths of tissue repaired with liquid albumin solder reinforced with a biodegradable polymer film compared to unreinforced control specimens. It was hypothesized that the breaking strength increase was due to reinforcement of the liquid solder cohesive strength. Immersion in a moist environment can decrease the adhesion of solder to tissue and negate any strength benefits gained from reinforcement. The purpose of this study was to determine if hydrated specimens repaired with reinforced solder would still be stronger than unreinforced controls. A 50%(w/v) bovine serum albumin solder with 0.5 mg/mL Indocyanine Green dye was used to repair an incision in bovine aorta. The solder was coagulated with 806-nm diode laser light. A poly(DL-lactic- co-glycolic acid) film was used to reinforce the solder (the controls had no reinforcement). The repaired tissues were immersed in phosphate buffered saline for time periods of 1 and 2 days. The breaking strengths of all of the hydrated specimens decreased compared to the acute breaking strengths. However, the reinforced specimens still had larger breaking strengths than the unreinforced controls. These results indicate that reinforcement of a liquid albumin solder may have the potential to improve the breaking strength in a clinical setting.

SEM/XPS analysis of fractured adhesively bonded graphite fibre-reinforced polyimide composites

NASA Technical Reports Server (NTRS)

Devilbiss, T. A.; Messick, D. L.; Wightman, J. P.; Progar, D. J.

1985-01-01

The surfaces of the graphite fiber-reinforced polyimide composites presently pretreated prior to bonding with polyimide adhesive contained variable amounts of a fluoropolymer, as determined by X-ray photoelectron spectroscopy. Lap shear strengths were determined for unaged samples and for those aged over 500- and 1000-hour periods at 177 and 232 C. Unaged sample lap strengths, which were the highest obtained, exhibited no variation with surface pretreatment, but a significant decrease is noted with increasing aging temperature. These thermally aged samples, however, had increased surface fluorine concentration, while a minimal concentration was found in unaged samples. SEM demonstrated a progressive shift from cohesive to adhesive failure for elevated temperature-aged composites.

Semiconductor Film Grown on a Circular Substrate: Predictive Modeling of Lattice-Misfit Stresses

NASA Astrophysics Data System (ADS)

Suhir, E.; Nicolics, J.; Khatibi, G.; Lederer, M.

2016-03-01

An effective and physically meaningful analytical predictive model is developed for the evaluation the lattice-misfit stresses (LMS) in a semiconductor film grown on a circular substrate (wafer). The two-dimensional (plane-stress) theory-of-elasticity approximation (TEA) is employed in the analysis. The addressed stresses include the interfacial shearing stress, responsible for the occurrence and growth of dislocations, as well as for possible delaminations and the cohesive strength of a buffering material, if any. Normal radial and circumferential (tangential) stresses acting in the film cross-sections and responsible for its short- and long-term strength (fracture toughness) are also addressed. The analysis is geared to the GaN technology.

Pier and contraction scour prediction in cohesive soils at selected bridges in Illinois

USGS Publications Warehouse

Straub, Timothy D.; Over, Thomas M.

2010-01-01

This report presents the results of testing the Scour Rate In Cohesive Soils-Erosion Function Apparatus (SRICOS-EFA) method for estimating scour depth of cohesive soils at 15 bridges in Illinois. The SRICOS-EFA method for complex pier and contraction scour in cohesive soils has two primary components. The first component includes the calculation of the maximum contraction and pier scour (Zmax). The second component is an integrated approach that considers a time factor, soil properties, and continued interaction between the contraction and pier scour (SRICOS runs). The SRICOS-EFA results were compared to scour prediction results for non-cohesive soils based on Hydraulic Engineering Circular No. 18 (HEC-18). On average, the HEC-18 method predicted higher scour depths than the SRICOS-EFA method. A reduction factor was determined for each HEC-18 result to make it match the maximum of three types of SRICOS run results. The unconfined compressive strength (Qu) for the soil was then matched with the reduction factor and the results were ranked in order of increasing Qu. Reduction factors were then grouped by Qu and applied to each bridge site and soil. These results, and comparison with the SRICOS Zmax calculation, show that less than half of the reduction-factor method values were the lowest estimate of scour; whereas, the Zmax method values were the lowest estimate for over half. A tiered approach to predicting pier and contraction scour was developed. There are four levels to this approach numbered in order of complexity, with the fourth level being a full SRICOS-EFA analysis. Levels 1 and 2 involve the reduction factors and Zmax calculation, and can be completed without EFA data. Level 3 requires some surrogate EFA data. Levels 3 and 4 require streamflow for input into SRICOS. Estimation techniques for both EFA surrogate data and streamflow data were developed.

What Determines CO₂ Solubility in Ionic Liquids? A Molecular Simulation Study.

PubMed

Klähn, Marco; Seduraman, Abirami

2015-08-06

Molecular dynamics (MD) simulations of 10 different pure and CO2-saturated ionic liquids are performed to identify the factors that determine CO2 solubility. Imidazolium-based cations with varying alkyl chain length and functionalization are paired with anions of different hydrophobicity and size. Simulations are carried out with an empirical force field based on liquid-phase charges. The partial molar volume of CO2 in ionic liquids (ILs) varies from 30 to 40 cm(3)/mol. This indicates that slight ion displacements are necessary to enable CO2 insertions. However, the absorption of CO2 does not affect the overall organization of ions in the ILs as demonstrated by almost equal cation-anion radial distribution functions of pure ILs and ILs saturated with CO2. The solubility of CO2 in ILs is not influenced by direct CO2-ion interactions. Instead, a strong correlation between the ratio of unoccupied space in pure ILs and their ability to absorb CO2 is found. This preformed unoccupied space is regularly dispersed throughout the ILs and needs to be expanded by slight ion displacements to accommodate CO2. The amount of preformed unoccupied space is a good indicator for ion cohesion in ILs. Weak electrostatic cation-anion interaction densities in ILs, i.e., weak ion cohesion, leads to larger average distances between ions and hence to more unoccupied space. Weak ion cohesion facilitates ion displacement to enable an expansion of empty space to accommodate CO2. Moreover, it is demonstrated that the strength of ion cohesion is primarily determined by the ion density, which in turn is given by the ion sizes. Ion cohesion is influenced additionally to a smaller extent by local electrostatic interactions among ion moieties between which CO2 is inserted and which do not depend on the ion density. Overall, the factors that determine the solubility of CO2 in ILs are identified consistently across a large variety of constituting ions through MD simulations.

Great Expectations: The U.S. Army X Corps in Korea, September-November 1950

DTIC Science & Technology

2014-05-22

nonetheless commenced operations in Korea with a newly formed team that had little experience working together.37 Moreover, the extensive demobilization...Division landed at Inchon close to full strength, the unit lacked experience , training, and cohesion.58 Like the 7th Infantry Division, the 3d Infantry...equipment’s readiness for operations in Korea. Ernest H. Giusti, Mobilization of the Marine Corps Reserve in the Korean Conflict, 17 Marine Division

Strength Property Estimation for Dry, Cohesionless Soils Using the Military Cone Penetrometer

DTIC Science & Technology

1992-05-01

by Meier and Baladi (1988). Their methodology is based on a theoretical formulation of the CI problem using cavity expansion theory to relate cone... Baladi (1981), incorporates three mechanical properties (cohesion, fric- tion angle, and shear modulus) and the total unit weight. Obviously, these four...unknown soil propertieE cannot be back-calculated directly from a single CI measurement. To ameliorate this problem, Meier and Baladi estimate the total

Women in Combat: The Operational Impact of Meeting A National Security Necessity

DTIC Science & Technology

1991-02-11

of physical strength and emotional stamina and impai.red male -bonding: United States public opinion; and the perceptions of America’s allies and...on the main thesis p6ints of demographics and noncombatants in the changing scenario of combat, and provides the arguments on both sides of the three...9 Unit Cohesion and Male -Bonding .................. 11 United States Public Opinion ......................... 12 Perceptions or Friend and Foe

Toward Interpreting Failure in Sintered-Silver Interconnection Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wereszczak, Andrew A; Waters, Shirley B

2016-01-01

The mechanical strength and subsequent reliability of a sintered-silver interconnection system is a function of numerous independent parameters. That system is still undergoing process development. Most of those parameters (e.g., choice of plating) are arguably and unfortunately taken for granted and are independent of the silver s cohesive strength. To explore such effects, shear strength testing and failure analyses were completed on a simple, mock sintered-silver interconnection system consisting of bonding two DBC ceramic substrates. Silver and gold platings were part of the test matrix, as was pre-drying strategies, and the consideration of stencil-printing vs. screen-printing. Shear strength of sintered-silvermore » interconnect systems was found to be was insensitive to the choice of plating, drying practice, and printing method provided careful and consistent processing of the sintered-silver are practiced. But if the service stress in sintered silver interconnect systems is anticipated to exceed ~ 60 MPa, then the system will likely fail.« less

Influence of the Conditioning Method for Pre-Sintered Zirconia on the Shear Bond Strength of Bilayered Porcelain/Zirconia

PubMed Central

Spintzyk, Sebastian; Yamaguchi, Kikue; Sawada, Tomofumi; Schille, Christine; Schweizer, Ernst; Ozeki, Masahiko; Geis-Gerstorfer, Jürgen

2016-01-01

This study evaluated the bond strength of veneering porcelain with an experimental conditioner-coated zirconia. Pre-sintered Y-TZP specimens (n = 44) were divided in two groups based on conditioning type. After sintering, all sample surfaces were sandblasted and layered with veneering porcelain. Additionally, half of the specimens in each group underwent thermal cycling (10,000 cycles, 5–55 °C), and all shear bond strengths were measured. After testing, the failure mode of each fractured specimen was determined. Differences were tested by parametric and Fisher’s exact tests (α = 0.05). The differences in bond strength were not statistically significant. Adhesive fractures were dominantly observed for the non-thermal cycled specimens. After thermal cycling, the conditioner-coated group showed cohesive and mixed fractures (p = 0.0021), whereas the uncoated group showed more adhesive fractures (p = 0.0021). Conditioning of the pre-sintered Y-TZP did not change the shear bond strength of the veneering porcelain, but did improve the failure mode after thermal cycling. PMID:28773885

Lap shear strength and healing capability of self-healing adhesive containing epoxy/mercaptan microcapsules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghazali, Habibah; Ye, Lin; Zhang, Ming-Qiu

The aim of this work is to develop a self-healing polymeric adhesive formulation with epoxy/mercaptan microcapsules. Epoxy/mercaptan microcapsules were dispersed into a commercialize two-part epoxy adhesive for developing self-healing epoxy adhesive. The influence of different content of microcapsules on the shear strength and healing capability of epoxy adhesive were investigated using single-lap-joints with average thickness of adhesive layer of about 180 µm. This self-healing adhesive was used in bonding of 5000 series aluminum alloys adherents after mechanical and alkaline cleaning surface treatment. The adhesion strength was measured and presented as function of microcapsules loading. The results indicated that the virgin lapmore » shear strength was increased by about 26% with addition of 3 wt% of self-healing microcapsules. 12% to 28% recovery of the shear strength is achieved after self-healing depending on the microcapsules content. Scanning electron microscopy was used to study fracture surface of the joints. The self-healing adhesives exhibit recovery of both cohesion and adhesion properties with room temperature healing.« less

Computational micromechanics of dynamic compressive loading of a brittle polycrystalline material using a distribution of grain boundary properties

NASA Astrophysics Data System (ADS)

Kraft, R. H.; Molinari, J. F.; Ramesh, K. T.; Warner, D. H.

A two-dimensional finite element model is used to investigate compressive loading of a brittle ceramic. Intergranular cracking in the microstructure is captured explicitly by using a distribution of cohesive interfaces. The addition of confining stress increases the maximum strength and if high enough, can allow the effective material response to reach large strains before failure. Increasing the friction at the grain boundaries also increases the maximum strength until saturation of the strength is approached. Above a transitional strain rate, increasing the rate-of-deformation also increases the strength and as the strain rate increases, fragment sizes of the damaged specimen decrease. The effects of flaws within the specimen were investigated using a random distribution at various initial flaw densities. The model is able to capture an effective modulus change and degradation of strength as the initial flaw density increases. Effects of confinement, friction, and spatial distribution of flaws seem to depend on the crack coalescence and dilatation of the specimen, while strain-rate effects are result of inertial resistance to motion.

Innovations in bonding to zirconia based ceramics: Part III. Phosphate monomer resin cements.

PubMed

Mirmohammadi, Hesam; Aboushelib, Moustafa N M; Salameh, Ziad; Feilzer, Albert J; Kleverlaan, Cornelis J

2010-08-01

To compare the bond strength values and the ranking order of three phosphate monomer containing resin cements using microtensile (microTBS) and microshear (microSBS) bond strength tests. Zirconia discs (Procera Zirconia) were bonded to resin composite discs (Filtek Z250) using three different cements (Panavia F 2.0, RelyX UniCem, and Multilink). Two bond strength tests were used to determine zirconia resin bond strength; microtensile bond strength test (microTBS) and microshear bond strength test (microSBS). Ten specimens were tested for each group (n=10). Two-way analysis of variance (ANOVA) was used to analyze the data (alpha=0.05). There were statistical significant differences in bond strength values and in the ranking order obtained using the two test methods. microTBS reported significant differences in bond strength values, whereas microSBS failed to detect such effect. Both Multilink and Panavia demonstrated basically cohesive failure in the resin cement while RelyX UniCem demonstrated interfacial failure. Based on the findings of this study, the data obtained using either microTBS or microSBS could not be directly compared. microTBS was more sensitive to material differences compared to microSBS which failed to detect such differences. Copyright 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Laboratory Evidence of Strength Recovery of Healed Faults

NASA Astrophysics Data System (ADS)

Masuda, K.

2015-12-01

Fault zones consist of a fault core and a surrounding damage zone. Fault zones are typically characterized by the presence of many healed surfaces, the strength of which is unknown. If a healed fault recovers its strength such that its cohesion is equal to or greater than that of the host rock, repeated cycles of fracture and healing may be one mechanism producing wide fault zones. I present laboratory evidence supporting the strength recovery of healed fault surface, obtained by AE monitoring, strain measurements and X-ray CT techniques. The loading experiment was performed with a specimen collected from an exhumed fault zone. Healed surfaces of the rock sample were interpreted to be parallel to slip surfaces. The specimen was a cylinder with 50 mm diameter and 100 mm long. The long axis of the specimen was inclined with respect to the orientation of the healed surfaces. The compression test used a constant loading rate under 50 MPa of confining pressure. Macroscopic failure occurred when the applied differential stress reached 439 MPa. The macro-fracture surface created during the experiment was very close to the preexisting plane. The AE hypocenters closely match the locations of the preexisting healed surface and the new fault plane. The experiment also revealed details of the initial stage of fault development. The new fault zone developed near, but not precisely on the preexisting healed fault plane. An area of heterogeneous structure where stress appears to have concentrated, was where the AEs began, and it was also where the fracture started. This means that the healed surface was not a weak surface and that healing strengthened the fault such that its cohesion was equal to or greater than that of the intact host rock. These results suggest that repeated cycles of fracture and healing may be the main mechanism creating wide fault zones with multiple fault cores and damage zones.

Mesoscale simulation of concrete spall failure

NASA Astrophysics Data System (ADS)

Knell, S.; Sauer, M.; Millon, O.; Riedel, W.

2012-05-01

Although intensively studied, it is still being debated which physical mechanisms are responsible for the increase of dynamic strength and fracture energy of concrete observed at high loading rates, and to what extent structural inertia forces on different scales contribute to the observation. We present a new approach for the three dimensional mesoscale modelling of dynamic damage and cracking in concrete. Concrete is approximated as a composite of spherical elastic aggregates of mm to cm size embedded in an elastic cement stone matrix. Cracking within the matrix and at aggregate interfaces in the μm range are modelled with adaptively inserted—initially rigid—cohesive interface elements. The model is applied to analyse the dynamic tensile failure observed in Hopkinson-Bar spallation experiments with strain rates up to 100/s. The influence of the key mesoscale failure parameters of strength, fracture energy and relative weakening of the ITZ on macromechanic strength, momentum and energy conservation is numerically investigated.

Improved mechanical performance of PBO fiber-reinforced bismaleimide composite using mixed O2/Ar plasma

NASA Astrophysics Data System (ADS)

Liu, Dong; Chen, Ping; Yu, Qi; Ma, Keming; Ding, Zhenfeng

2014-06-01

The mixed O2/Ar plasma was employed to enhance mechanical properties of the PBO/bismaleimide composite. The interlaminar shear strength was improved to 61.6 MPa or by 38.1%, but the composite brittleness increased. The plasma gas compositions exhibited notable effects on the interfacial adhesion strength. XPS results suggested that the mixed plasma presented higher activation effects on the surface chemical compositions than pure gas plasmas and a larger number of oxygen atoms and hydrophilic groups were introduced on the fiber surface due to the synergy effect, but the synergy effect was considerably performed only within the O2 percentage range of 40-60%. The fibers surface was increasingly etched with growing the O2 contents in the plasma, deteriorating the fibers tensile strength. SEM micrographs demonstrated that the composite shear fracture changed from debonding to cohesive failure in the matrices, and the improving mechanisms were discussed.

Immediate vs delayed repair bond strength of a nanohybrid resin composite.

PubMed

El-Askary, Farid S; El-Banna, Ahmed H; van Noort, Richard

2012-06-01

To evaluate both the immediate and water-stored repair tensile bond strength (TBS) of a nanohybrid resin composite using different bonding protocols. One hundred sixty half hourglass-shaped slabs were prepared. Eighty half-slabs were wet ground immediately after light curing using high-speed abrasive burs, while the other half-slabs were stored in water for one month (delayed) and then wet ground for repair. Each set of the 80 repaired slabs was split into two groups to be tested for TBS after 24 h or 1 month of water storage. For all repaired slabs, either immediate or delayed, four bonding procedures were used involving wet and dry bonding with a 3-step etch-and-rinse adhesive with or without silane pretreatment. TBS tests were performed at a crosshead speed of 0.5 mm/min. To determine the cohesive strength of the resin composite itself, which served as the reference, additional whole slabs were prepared and tested in tension after a 24-h (n = 10) and a 1-month storage period (n = 10). Failure modes were evaluated using a stereomicroscope at 40X magnification. Three-way ANOVA was run to test the effect of water storage, testing time, bonding protocols, and their interactions on the repair TBS, which was given as a percentage of the reference values. For the immediate repair groups, the repair TBS ranged from 40% to 61.9% after 24-h storage and from 26% to 53.1% after 1-month water storage compared to the TBS of the whole slabs. For the delayed repair group, the repaired TBS ranged from 47.2% to 63.6% for the 24-h repairs and from 32.2% to 44.2% for the test groups stored in water for 1 month. Three-way ANOVA revealed that water storage had no significant effect on the repair TBS (p = 0.619). Both testing time and bonding protocols had a significant effect on the repair TBS (p = 0.001). The interactions between the independent variables (water storage, testing time, and bonding protocols) had no significant effect (p = 0.067). The repair bond strength was consistently and highly significantly less than the cohesive strength of the composite. A delay of 1 month before carrying out the repair had no effect on the bond strength, irrespective of the bonding procedure used. Silane treatment did not improve the repair bond strength. In all instances, except for the immediate wet bonding plus silane procedure and delayed dry bonding, the bond strength of the repairs significantly dropped after 1 month of storage in water.

Tensile strength and failure mechanisms of tantalum at extreme strain rates

NASA Astrophysics Data System (ADS)

Hahn, Eric; Fensin, Saryu; Germann, Timothy; Meyers, Marc

Non-equilibrium molecular dynamics simulations are used to probe the tensile response of monocrystalline, bicrystalline, and nanocrystalline tantalum over six orders of magnitude of strain rate. Our analysis of the strain rate dependence of strength is extended to over nine orders of magnitude by bridging the present simulations to recent laser-driven shock experiments. Tensile strength shows a power-law dependence with strain rate over this wide range, with different relationships depending on the initial microstructure and active deformation mechanism. At high strain rates, multiple spall events occur independently and continue to occur until communication occurs by means of relaxation waves. Temperature plays a significant role in the reduction of spall strength as the initial shock required to achieve such large strain rates also contributes to temperature rise, through pressure-volume work as well as visco-plastic heating, which leads to softening and sometimes melting upon release. At ultra-high strain rates, those approaching or exceeding the atomic vibrational frequency, spall strength saturates at the ultimate cohesive strength of the material. UC Research Laboratories Grant (09-LR-06-118456-MEYM); Department of Energy NNSA/SSAP (DE-NA0002080); DOE ASCR Exascale Co-design Center for Materials in Extreme Environments.

Looking into the evolution of granular asteroids in the Solar System

NASA Astrophysics Data System (ADS)

Sánchez, Paul; Scheeres, Daniel; Hirabayashi, Masatoshi; Tardivel, Simon

2017-06-01

By now it has been accepted that most of the small asteroids in the Solar System are granular aggregates kept together by gravitational and possibly, cohesive forces. These aggregates can form, deform and disrupt over millennia subjected to different internal and external factors that would ultimately determine how they evolve over time. Parameters such as porosity, cohesive and tensile strength, angles of friction, particle size distributions, stress states, heterogeneity and yield criteria among others, determine how these granular systems will react when subjected to different, changing, external factors. These external factors include solar photon momentum, gravitational tides, micro- and macro-impacts and are believed to have produced and shaped the current asteroid population. In our research we use a combination of Soil Mechanics theory, Soft-Sphere Discrete Element Method (SSDEM) Simulations and Orbital Mechanics in order to understand how simulated, homogeneous and heterogeneous, ellipsoidal and spherical gravitational aggregates, a crude but useful representation of an asteroid, evolve when rotated to the point of disruption. Then, we compare our results to the shapes of observed asteroids as well as to the disruption patterns of a few active asteroids. Our results lead us to believe that the different shapes of observed asteroids as well as their unique disruption patterns could give us clues about their internal structure, strength and geophysical properties in general.

Effect of ultraviolet light irradiation on bond strength of fiber post: Evaluation of surface characteristic and bonded area of fiber post with resin cement.

PubMed

Reza, Fazal; Ibrahim, Nur Sukainah

2015-01-01

Fiber post is cemented to a root canal to restore coronal tooth structure. This research aims to evaluate the effect of ultraviolet (UV) irradiation on bond strength of fiber post with resin cement. A total of 40 of the two types of fiber posts, namely, FRC Prostec (FRC) and Fiber KOR (KOR), were used for the experiment. UV irradiation was applied on top of the fiber post surface for 0, 15, 20, and 30 min. The irradiated surface of the fiber posts (n = 5) were immediately bonded with resin cement (Rely X U200) after UV irradiation. Shear bond strength (SBS) MPa was measured, and the dislodged area of post surfaces was examined with scanning electron microscopes. Changes in surface roughness (Ra) of the FRC group after UV irradiation were observed (n = 3) using atomic force microscopy. Data of SBS were statistically analyzed using one-way analysis of variance, followed by multiple comparisons (P < 0.05). SBS was significantly higher for 20 min of UV irradiation of the FRC group while significantly higher SBS was observed with 15 min of UV irradiation of the KOR group. Resin cement was more evident (cohesive failure) on the dislodged post surface of the UV treated groups compared with the control. The surface roughness of the FRC post was Ra = 175.1 nm and Ra = 929.2 nm for the control and the 20 min group, respectively. Higher surface roughness of the UV irradiated group indicated formation of mechanical retention on the fiber post surface. Evidence of cohesive failure was observed which indicated higher SBS of fiber post with the UV irradiated group.

Effect of ultraviolet light irradiation on bond strength of fiber post: Evaluation of surface characteristic and bonded area of fiber post with resin cement

PubMed Central

Reza, Fazal; Ibrahim, Nur Sukainah

2015-01-01

Objective: Fiber post is cemented to a root canal to restore coronal tooth structure. This research aims to evaluate the effect of ultraviolet (UV) irradiation on bond strength of fiber post with resin cement. Materials and Methods: A total of 40 of the two types of fiber posts, namely, FRC Prostec (FRC) and Fiber KOR (KOR), were used for the experiment. UV irradiation was applied on top of the fiber post surface for 0, 15, 20, and 30 min. The irradiated surface of the fiber posts (n = 5) were immediately bonded with resin cement (Rely X U200) after UV irradiation. Shear bond strength (SBS) MPa was measured, and the dislodged area of post surfaces was examined with scanning electron microscopes. Changes in surface roughness (Ra) of the FRC group after UV irradiation were observed (n = 3) using atomic force microscopy. Data of SBS were statistically analyzed using one-way analysis of variance, followed by multiple comparisons (P < 0.05). Results: SBS was significantly higher for 20 min of UV irradiation of the FRC group while significantly higher SBS was observed with 15 min of UV irradiation of the KOR group. Resin cement was more evident (cohesive failure) on the dislodged post surface of the UV treated groups compared with the control. The surface roughness of the FRC post was Ra = 175.1 nm and Ra = 929.2 nm for the control and the 20 min group, respectively. Conclusions: Higher surface roughness of the UV irradiated group indicated formation of mechanical retention on the fiber post surface. Evidence of cohesive failure was observed which indicated higher SBS of fiber post with the UV irradiated group. PMID:25713488

[Cereal bars with soy protein and wheat germ, physicochemical characteristics and texture during the storage].

PubMed

Castro Freitas, Daniela D G

2005-09-01

Studies analyzing cereal bars have reported on consumer characteristics and preferences in sensory analyses and on their market growth, however little has been published on their physicochemical data and texture properties. Thus the objective of this research was to provide information about the storage of a cereal bar formulation with high protein and vitamin levels based on soy protein and wheat germ, packaged in 3 different films (A: PET/PEBD; B: PETmet/PEBD; C: PET/PEBD/AL/PEBD), during 6 months under environmental conditions of temperature (25 +/- 2 degrees C) and relative humidity (56%). The moisture content, water activity, pH and total acidity of the cereal bars were determined. The textural measurements accompanied during storage were breaking strength, hardness and cohesiveness. The cereal bars presented variations in water activity (Aw), moisture content and total acidity during storage. The moisture content of the bars tended to increase, which led to a significant (p = 0.05) influence on the texture characteristics of breaking strength and hardness, in the different packaging films tested. The increase in the values for breaking strength (A: 4756,5N; B: 5093,0N; C: 5575,6N) at 45 days of storage was attributed to a possible crystallization of the agglutinating syrup used for the bars. The textured soy protein used in the formulation could also have contributed to this fact due to its hygroscopic character, also interfering in the decrease in the cohesiveness measurements (deformation) with time. The effect of the different barrier properties of the packaging films tested was significant (p < 0.05) in the stability of the cereal bars during storage.

Processing of Aluminum-Graphite Particulate Metal Matrix Composites by Advanced Shear Technology

NASA Astrophysics Data System (ADS)

Barekar, N.; Tzamtzis, S.; Dhindaw, B. K.; Patel, J.; Hari Babu, N.; Fan, Z.

2009-12-01

To extend the possibilities of using aluminum/graphite composites as structural materials, a novel process is developed. The conventional methods often produce agglomerated structures exhibiting lower strength and ductility. To overcome the cohesive force of the agglomerates, a melt conditioned high-pressure die casting (MC-HPDC) process innovatively adapts the well-established, high-shear dispersive mixing action of a twin screw mechanism. The distribution of particles and properties of composites are quantitatively evaluated. The adopted rheo process significantly improved the distribution of the reinforcement in the matrix with a strong interfacial bond between the two. A good combination of improved ultimate tensile strength (UTS) and tensile elongation (ɛ) is obtained compared with composites produced by conventional processes.

Adhesive retention of experimental fiber-reinforced composite, orthodontic acrylic resin, and aliphatic urethane acrylate to silicone elastomer for maxillofacial prostheses.

PubMed

Kosor, Begüm Yerci; Artunç, Celal; Şahan, Heval

2015-07-01

A key factor of an implant-retained facial prosthesis is the success of the bonding between the substructure and the silicone elastomer. Little has been reported on the bonding of fiber reinforced composite (FRC) to silicone elastomers. Experimental FRC could be a solution for facial prostheses supported by light-activated aliphatic urethane acrylate, orthodontic acrylic resin, or commercially available FRCs. The purpose of this study was to evaluate the bonding of the experimental FRC, orthodontic acrylic resin, and light-activated aliphatic urethane acrylate to a commercially available high-temperature vulcanizing silicone elastomer. Shear and 180-degree peel bond strengths of 3 different substructures (experimental FRC, orthodontic acrylic resin, light-activated aliphatic urethane acrylate) (n=15) to a high-temperature vulcanizing maxillofacial silicone elastomer (M511) with a primer (G611) were assessed after 200 hours of accelerated artificial light-aging. The specimens were tested in a universal testing machine at a cross-head speed of 10 mm/min. Data were collected and statistically analyzed by 1-way ANOVA, followed by the Bonferroni correction and the Dunnett post hoc test (α=.05). Modes of failure were visually determined and categorized as adhesive, cohesive, or mixed and were statistically analyzed with the chi-squared goodness-of-fit test (α=.05). As the mean shear bond strength values were evaluated statistically, no difference was found among the experimental FRC, aliphatic urethane acrylate, and orthodontic acrylic resin subgroups (P>.05). The mean peel bond strengths of experimental fiber reinforced composite and aliphatic urethane acrylate were not found to be statistically different (P>.05). The mean value of the orthodontic acrylic resin subgroup peel bond strength was found to be statistically lower (P<.05). Shear test failure types were found to be statistically different (P<.05), whereas 180-degree peel test failure types were not found to be statistically significant (P>.05). Shear forces predominantly exhibited cohesive failure (64.4%), whereas peel forces predominantly exhibited adhesive failure (93.3%). The mean shear bond strengths of the experimental FRC and aliphatic urethane acrylate groups were not found to be statistically different (P>.05). The mean value of the 180-degree peel strength of the orthodontic acrylic resin group was found to be lower (P<.05). Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Interfacial characteristics and determination of cohesive and adhesive strength of plasma-coated hydroxyapatite via nanoindentation and microscratch techniques.

PubMed

McManamon, Colm; de Silva, Johann P; Power, John; Ramirez-Garcia, Sonia; Morris, Michael A; Cross, Graham L W

2014-09-30

We investigate the chemical composition and mechanical properties of plasma-deposited hydroxyapatite on grit-blasted Ti-6Al-4V coupons as models of typical prosthetic hip implants. Nanoindentation is used to extract the mechanical properties of the hydroxyapatite (HA) coating and to evaluate the behavior of the material as a function of distance from the interface. A microscratch technique was used to determine parameters of cohesive and adhesive failure of the material that are critical in determining the functionality of these biomedical devices. This delamination method has not been studied in detail before and is usually considered to be unsuitable because of the thickness of the HA and the roughness of the substrate. However, through cross-section analysis of the scratch test, we can determine the point at which the HA delaminates from the substrate. It was concluded that spallation occurs locally, and there is no evidence of gross spallation, indicating that the coating is well adhered to the substrate.

Waterborne polyurethane-acrylic hybrid nanoparticles by miniemulsion polymerization: applications in pressure-sensitive adhesives.

PubMed

Lopez, Aitziber; Degrandi-Contraires, Elise; Canetta, Elisabetta; Creton, Costantino; Keddie, Joseph L; Asua, José M

2011-04-05

Waterborne polyurethane-acrylic hybrid nanoparticles for application as pressure-sensitive adhesives (PSAs) were prepared by one-step miniemulsion polymerization. The addition of polyurethane to a standard waterborne acrylic formulation results in a large increase in the cohesive strength and hence a much higher shear holding time (greater than seven weeks at room temperature), which is a very desirable characteristic for PSAs. However, with the increase in cohesion, there is a decrease in the relative viscous component, and hence there is a decrease in the tack energy. The presence of a small concentration of methyl methacrylate (MMA) in the acrylic copolymer led to phase separation within the particles and created a hemispherical morphology. The tack energy was particularly low in the hybrid containing MMA because of the effects of lower energy dissipation and greater cross-linking. These results highlight the great sensitivity of the viscoelastic and adhesive properties to the details of the polymer network architecture and hence to the precise composition and synthesis conditions.

Chemistry of the calcite/water interface: Influence of sulfate ions and consequences in terms of cohesion forces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pourchet, Sylvie, E-mail: sylvie.pourchet@u-bourgogne.fr; Pochard, Isabelle; Brunel, Fabrice

2013-10-15

Calcite suspensions are used to mimic the behavior of more complex cementitious systems. Therefore the characterization of calcite–water interface in strong alkaline conditions, through ionic adsorption, electrokinetic measurements, static rheology and atomic force microscopy is a prerequisite. Calcium, a potential determining ion for calcite, adsorbs specifically onto the weakly positively charged calcite surface in water. This leads to an increase of the repulsive electric double layer force and thus weakens the particle cohesion. Sulfate adsorption, made at constant calcium concentration and ionic strength, significantly increases the attractive interactions between the calcite particles despite its very low adsorption. This is attributedmore » to a lowering of the electrostatic repulsion in connection with the evolution of the zeta potential. The linear relationship found between the yield stress and ζ{sup 2} proves that the classical DLVO theory applies for these systems, contrary to what was previously observed with C–S–H particles under the same conditions.« less

Direct Scaffolding of Biomimetic Hydroxyapatite-gelatin Nanocomposites using Aminosilane Cross-linker for Bone Regeneration

PubMed Central

Chiu, Chi-Kai; Ferreira, Joao; Luo, Tzy-Jiun M.; Geng, Haixia; Lin, Feng-Chang; Ko, Ching-Chang

2012-01-01

Hydroxyapatite-gelatin modified siloxane (GEMOSIL) nanocomposite was developed by coating, kneading and hardening processes to provide formable scaffolding for alloplastic graft applications. The present study aims to characterize scaffolding formability and mechanical properties of GEMOSIL, and to test the in vitro and in vivo biocompatibility of GEMOSIL. Buffer Solution initiated formable paste followed by the sol-gel reaction led to a final hardened composite. Results showed the adequate coating of aminosilane, 11–19 wt%, affected the cohesiveness of the powders and the final compressive strength (69 MPa) of the composite. TGA and TEM results showed the effective aminosilane coating that preserves hydroxyapatite-gelatin nanocrystals from damage. Both GEMOSIL with and without titania increased the mineralization of preosteoblasts in vitro. Only did titania additives revealed good in vivo bone formation in rat calvarium defects. The scaffolding formability, due to cohesive bonding among GEMOSIL particles, could be further refined to fulfill the complicated scaffold processes. PMID:22669282

Interface structure and mechanics between graphene and metal substrates: a first-principles study

NASA Astrophysics Data System (ADS)

Xu, Zhiping; Buehler, Markus J.

2010-12-01

Graphene is a fascinating material not only for technological applications, but also as a test bed for fundamental insights into condensed matter physics due to its unique two-dimensional structure. One of the most intriguing issues is the understanding of the properties of graphene and various substrate materials. In particular, the interfaces between graphene and metal substrates are of critical importance in applications of graphene in integrated electronics, as thermal materials, and in electromechanical devices. Here we investigate the structure and mechanical interactions at a graphene-metal interface through density functional theory (DFT)-based calculations. We focus on copper (111) and nickel (111) surfaces adhered to a monolayer of graphene, and find that their cohesive energy, strength and electronic structure correlate directly with their atomic geometry. Due to the strong coupling between open d-orbitals, the nickel-graphene interface has a much stronger cohesive energy with graphene than copper. We also find that the interface cohesive energy profile features a well-and-shoulder shape that cannot be captured by simple pair-wise models such as the Lennard-Jones potential. Our results provide a detailed understanding of the interfacial properties of graphene-metal systems, and help to predict the performance of graphene-based nanoelectronics and nanocomposites. The availability of structural and energetic data of graphene-metal interfaces could also be useful for the development of empirical force fields for molecular dynamics simulations.

Alternative Gas Mixtures in Arc Spraying: A Chance to Improve Coating Properties and Residual Stress States

NASA Astrophysics Data System (ADS)

Hauer, Michél; Henkel, Knuth Michael; Krebs, Sebastian; Kroemmer, Werner

2018-01-01

The highly cavitation erosion-resistant propeller alloys CuAl9Ni5Fe4Mn (Ni-Al-Bronze) and CuMn13Al8Fe3Ni2 (Mn-Al-Bronze) were arc-sprayed using a mixture of nitrogen and 2% of hydrogen as atomizing gas and different traverse speeds. The objective was to identify the influences of the different spraying conditions, such as temperature regime and melting loss, on the resulting residual stress states and coating properties. Residual stresses were measured by the incremental hole-drilling method using ESPI. Temperature measurements were carried out by thermographic imaging. Microstructural, chemical and mechanical analyses were realized to examine adhesive and cohesive properties. Additionally, the cavitation erosion behavior was investigated to analyze cohesive coating properties. The spraying process itself was improved, which was apparent by mainly enhanced deposition efficiency and reduced surface temperatures. The amount of oxides and pores as well as the melting loss of alloying elements were reduced. Moreover, an increased cavitation erosion resistance and thus coating cohesion as well as less residual stresses were identified. The change in atomizing gas diminished the impact of the quenching stresses on the coating properties. In contrast, the adhesive strength, Young's moduli and partially the hardness were slightly reduced. With regard to materials, Ni-Al-Bronze revealed superior coating properties in comparison with Mn-Al-Bronze.

Differential associations between Social Anxiety Disorder, family cohesion, and suicidality across racial/ethnic groups: Findings from the National Comorbidity Survey-Adolescent (NCS-A).

PubMed

Rapp, Amy M; Lau, Anna; Chavira, Denise A

2017-05-01

The proposed research seeks to introduce a novel model relating Social Anxiety Disorder (SAD) and suicide outcomes (i.e., passive suicidal ideation, active suicidal ideation, and suicide attempts) in diverse adolescents. This model posits that family cohesion is one pathway by which suicide risk is increased for socially anxious youth, and predicts that the relationships between these variables may be of different strength in Latino and White subgroups and across gender. Data from a sample of Latino (n=1922) and non-Hispanic White (hereafter referred to as White throughout) (n=5648) male and female adolescents who participated in the National Comorbidity Survey-Adolescent were used for this study. Analyses were conducted using generalized structural equation modeling. Results showed that the mediation model held for White females. Further examination of direct pathways highlighted SAD as a risk factor unique to Latinos for active suicidal ideation and suicide attempt, over and above comorbid depression and other relevant contextual factors. Additionally, family cohesion showed a strong association with suicide outcomes across groups, with some inconsistent findings for White males. Overall, it appears that the mechanism by which SAD increases risk for suicidality is different across groups, indicating further need to identify relevant mediators, especially for racial/ethnic minority youth. Copyright © 2016 Elsevier Ltd. All rights reserved.

Discrete element modeling of free-standing wire-reinforced jammed granular columns

NASA Astrophysics Data System (ADS)

Iliev, Pavel S.; Wittel, Falk K.; Herrmann, Hans J.

2018-02-01

The use of fiber reinforcement in granular media is known to increase the cohesion and therefore the strength of the material. However, a new approach, based on layer-wise deployment of predetermined patterns of the fiber reinforcement has led self-confining and free-standing jammed structures to become viable. We have developed a novel model to simulate fiber-reinforced granular materials, which takes into account irregular particles and wire elasticity and apply it to study the stability of unconfined jammed granular columns.

REFRACTORY ARTICLE AND PROCESS OF MANUFACTURING SAME

DOEpatents

Hamilton, N.E.

1957-12-10

A method is described for fabricating improved uranium oxide crucibles. In the past, such crucibles have lacked mechanical strength due to the poor cohesion of the uranium oxide particles. This difficulty has now been overcome by admixing with the uranium oxide a quantity of a refractory oxide binder, and dry pressing and sintering the resulting mixture into the desired shape. Suitable as binders are BeO, CaO, Al/sub 2/C/sub 3/, and ThO/sub 2/ among others.

Developing Team Cohesion: A Quasi-Field Experiment

DTIC Science & Technology

2004-03-01

social cohesion and task cohesion which may be very different and often produced opposite effects. Carless and Depaola (2000) defined task cohesion as... Social cohesion was defined as the motivation to develop and retain social interaction within the group. Whether cohesion is studied as one construct...that task cohesion and social cohesion have differing effects on performance. Mullen and Cooper (1994) showed that task cohesion had a positive

Avalanche weak layer shear fracture parameters from the cohesive crack model

NASA Astrophysics Data System (ADS)

McClung, David

2014-05-01

Dry slab avalanches release by mode II shear fracture within thin weak layers under cohesive snow slabs. The important fracture parameters include: nominal shear strength, mode II fracture toughness and mode II fracture energy. Alpine snow is not an elastic material unless the rate of deformation is very high. For natural avalanche release, it would not be possible that the fracture parameters can be considered as from classical fracture mechanics from an elastic framework. The strong rate dependence of alpine snow implies that it is a quasi-brittle material (Bažant et al., 2003) with an important size effect on nominal shear strength. Further, the rate of deformation for release of an avalanche is unknown, so it is not possible to calculate the fracture parameters for avalanche release from any model which requires the effective elastic modulus. The cohesive crack model does not require the modulus to be known to estimate the fracture energy. In this paper, the cohesive crack model was used to calculate the mode II fracture energy as a function of a brittleness number and nominal shear strength values calculated from slab avalanche fracture line data (60 with natural triggers; 191 with a mix of triggers). The brittleness number models the ratio of the approximate peak value of shear strength to nominal shear strength. A high brittleness number (> 10) represents large size relative to fracture process zone (FPZ) size and the implications of LEFM (Linear Elastic Fracture Mechanics). A low brittleness number (e.g. 0.1) represents small sample size and primarily plastic response. An intermediate value (e.g. 5) implies non-linear fracture mechanics with intermediate relative size. The calculations also implied effective values for the modulus and the critical shear fracture toughness as functions of the brittleness number. The results showed that the effective mode II fracture energy may vary by two orders of magnitude for alpine snow with median values ranging from 0.08 N/m (non-linear) to 0.18 N/m (LEFM) for median slab density around 200 kg/m3. Schulson and Duval (2009) estimated the fracture energy of solid ice (mode I) to be about 0.22-1 N/m which yields rough theoretical limits of about 0.05- 0.2 N/m for density 200 kg/m3 when the ice volume fraction is accounted for. Mode I results from lab tests (Sigrist, 2006) gave 0.1 N/m (200 kg/m3). The median effective mode II shear fracture toughness was calculated between 0.31 to 0.35 kPa(m)1/2 for the avalanche data. All the fracture energy results are much lower than previously calculated from propagation saw tests (PST) results for a weak layer collapse model (1.3 N/m) (Schweizer et al., 2011). The differences are related to model assumptions and estimates of the effective slab modulus. The calculations in this paper apply to quasi-static deformation and mode II weak layer fracture whereas the weak layer collapse model is more appropriate for dynamic conditions which follow fracture initiation (McClung and Borstad, 2012). References: Bažant, Z.P. et al. (2003) Size effect law and fracture mechanics of the triggering of dry snow slab avalanches, J. Geophys. Res. 108(B2): 2119, doi:10.1029/2002JB))1884.2003. McClung, D.M. and C.P. Borstad (2012) Deformation and energy of dry snow slabs prior to fracture propagation, J. Glaciol. 58(209), 2012 doi:10.3189/2012JoG11J009. Schulson, E.M and P. Duval (2009) Creep and fracture of ice, Cambridge University Press, 401 pp. Schweizer, J. et al. (2011) Measurements of weak layer fracture energy, Cold Reg. Sci. and Tech. 69: 139-144. Sigrist, C. (2006) Measurement of fracture mechanical properties of snow and application to dry snow slab avalanche release, Ph.D thesis: 16736, ETH, Zuerich: 139 pp.

Fracture propagation in Indiana Limestone interpreted via linear softening cohesive fracture model

NASA Astrophysics Data System (ADS)

Rinehart, Alex J.; Bishop, Joseph E.; Dewers, Thomas

2015-04-01

We examine the use of a linear softening cohesive fracture model (LCFM) to predict single-trace fracture growth in short-rod (SR) and notched 3-point-bend (N3PB) test configurations in Indiana Limestone. The broad goal of this work is to (a) understand the underlying assumptions of LCFM and (b) use experimental similarities and deviations from the LCFM to understand the role of loading paths of tensile fracture propagation. Cohesive fracture models are being applied in prediction of structural and subsurface fracture propagation in geomaterials. They lump the inelastic processes occurring during fracture propagation into a thin zone between elastic subdomains. LCFM assumes that the cohesive zone initially deforms elastically to a maximum tensile stress (σmax) and then softens linearly from the crack opening width at σmax to zero stress at a critical crack opening width w1. Using commercial finite element software, we developed LCFMs for the SR and N3PB configurations. After fixing σmax with results from cylinder splitting tests and finding an initial Young's modulus (E) with unconfined compressive strength tests, we manually calibrate E and w1 in the SR model against an envelope of experimental data. We apply the calibrated LCFM parameters in the N3PB geometry and compare the model against an envelope of N3PB experiments. For accurate simulation of fracture propagation, simulated off-crack stresses are high enough to require inclusion of damage. Different elastic moduli are needed in tension and compression. We hypothesize that the timing and location of shear versus extensional micromechanical failures control the qualitative macroscopic force-versus-displacement response in different tests. For accurate prediction, the LCFM requires a constant style of failure, which the SR configuration maintains until very late in deformation. The N3PB configuration does not maintain this constancy. To be broadly applicable between geometries and failure styles, the LCFM would require additional physics, possibly including elastoplastic damage in the bulk material and more complicated cohesive softening models.

Demographic faultlines: a meta-analysis of the literature.

PubMed

Thatcher, Sherry M B; Patel, Pankaj C

2011-11-01

We propose and test a theoretical model focusing on antecedents and consequences of demographic faultlines. We also posit contingencies that affect overall team dynamics in the context of demographic faultlines, such as the study setting and performance measurement. Using meta-analysis structural equation modeling with a final data set consisting of 311 data points (i.e., k [predictor-criterion relationships]), from 39 studies that were obtained from 36 papers with a total sample size of 24,388 individuals in 4,366 teams, we found that sex and racial diversity increased demographic faultline strength more than did diversity on the attributes of functional background, educational background, age, and tenure. Demographic faultline strength was found to increase task and relationship conflict as well as decrease team cohesion. Furthermore, although demographic faultline strength decreased both team satisfaction and team performance, there was a stronger decrease in team performance than in team satisfaction. The strength of these relationships increased when the study was conducted in the lab rather than in the field. We describe the theoretical and practical implications of these findings for advancing the study of faultlines. (c) 2011 APA, all rights reserved.

In Vitro Evaluation of Shear Bond Strength of Nanocomposites to Dentin

PubMed Central

Vellanki, Vinay Kumar; Shetty, Vikram K; Kushwah, Sudhanshu; Goyal, Geeta; Chandra, S.M. Sharath

2015-01-01

Aims: To compare the shear bond strength of nanocomposites to dentin using three different types of adhesive systems; and to test few specimens under Scanning Electron Microscope (SEM) for analysing whether the bond failure is adhesive or cohesive. Materials and Methods: Sixty human premolar teeth were selected and were randomly grouped, with 20 specimens in each group: group 1 - fluoride releasing dentin bonding agent; group 2 - antibacterial containing dentin bonding agent; and group 3 - one step conventional self etch adhesive. Each group was treated with its respective bonding agents, composite resin build up was done, and shear bond strengths were tested using Instron Universal testing machine. Few of the specimens were tested under SEM. Results: The results were statistically analysed using One-way ANOVA and paired t-test. It was observed that group 3 has the highest shear bond strength followed by group 2, and then group 1. Adhesive failures and mixed failures were most frequent types of failures as seen under SEM. Conclusion: Addition of antimicrobial agent decreases the bond strength of dentin bonding agent and addition of fluoride further decreases the bond strength. From SEM results it can be concluded that the zone of failure could not be defined and also that the failure mode was independent of the dentin bonding agent used. PMID:25738077

Investigation of the mechanical properties of organoplastic under shock wave loading conditions

NASA Astrophysics Data System (ADS)

Bragov, A. M.; Igumnov, L. A.; Konstantinov, A. Yu; Lomunov, A. K.

2018-04-01

The paper presents results of dynamic tests of a typical representative of new composite and damping materials: organoplastics. Compression testing was performed using the traditional Kolsky method and its original modification. The strength and deformation properties of organoplastics under conditions of uniaxial stress and uniaxial deformation were studied. When the organoplastic is compressed transversely to the Kevlar fabric layers under conditions of a uniaxial stress state, the material begins to break down (to lose the layer cohesion) at a stress of about 200 MPa, while under the conditions of uniaxial strain, it retains its apparent integrity at stresses up to 500 MPa. The small value of the lateral thrust factor indicates a large internal strength of the material in tension in the radial direction.

Synthesis of geopolymer composites from a mixture of ferronickel slag and fly ash

NASA Astrophysics Data System (ADS)

Liu, Yun; Zhang, Kang; Feng, Enjuan; Zhao, Hongyi; Liu, Futian

2017-03-01

The synthesis of geopolymers using ferronickel slag and fly ash under alkaline activation was studied. In order to study the effects of different fly ash content on the mechanical properties of the geopolymers produced, the compressive strength of samples was tested at 3, 7, 28 days. The results showed that when the fly ash content was 40%, the compressive strength reached the highest (110.32MPa) at 28 days. XRD analysis showed that the ferronickel slag geopolymers had amorphous aluminosilicate phase formation, indicating that the hydration reaction occurred. FTIR analysis showed the reaction of the geopolymers generated at Si-O-T (Si, Al) and Al-O-Si three-dimensional network. In SEM images, the structure of the geopolymers with 40% fly ash was more compact and cohesive.

Production and functional evaluation of a protein concentrate from giant squid (Dosidicus gigas) by acid dissolution and isoelectric precipitation.

PubMed

Cortés-Ruiz, Juan A; Pacheco-Aguilar, Ramón; Elena Lugo-Sánchez, M; Gisela Carvallo-Ruiz, M; García-Sánchez, Guillermina

2008-09-15

A protein concentrate from giant squid (Dosidicus gigas) was produced under acidic conditions and its functional-technological capability evaluated in terms of its gel-forming ability, water holding capacity and colour attributes. Technological functionality of the concentrate was compared with that of squid muscle and a neutral concentrate. Protein-protein aggregates insoluble at high ionic strength (I=0.5M), were detected in the acidic concentrate as result of processing with no preclusion of its gel-forming ability during the sol-to-gel thermal transition. Even though washing under acidic condition promoted autolysis of the myosin heavy chain, the acidic concentrate displayed an outstanding ability to gel giving samples with a gel strength of 455 and 1160gcm at 75% and 90% compression respectively, and an AA folding test grade indicative of high gel strength, elasticity, and cohesiveness. The process proved to be a good alternative for obtaining a functional protein concentrate from giant squid muscle. Copyright © 2008. Published by Elsevier Ltd.

Enhancement of low pressure cold sprayed copper coating adhesion by laser texturing on aluminum substrates

NASA Astrophysics Data System (ADS)

Knapp, Wolfgang; Gillet, Vincent; Courant, Bruno; Aubignat, Emilie; Costil, Sophie; Langlade, Cécile

2017-02-01

Surface pre-treatment is fundamental in thermal spraying processes to obtain a sufficient bonding strength between substrate and coating. Different pre-treatments can be used, mostly grit-blasting for current industrial applications. This study is focused on Cu-Al2O3 coatings obtained by Low Pressure Cold Spray on AW5083 aluminum alloy substrate. Bonding strength is measured by tensile adhesion test, while deposition efficiency is measured. Substrates are textured by laser, using a pattern of equally spaced grooves with almost constant diameter and variations of depth. Results show that bonding strength is improved up to +81% compared to non-treated substrate, while deposition efficiency remains constant. The study of the samples after rupture reveals a modification of the failure mode, from mixed failure to cohesive failure. A modification of crack propagation is also noticed, the shape of laser textured grooves induces a deviation of cracks inside the coating instead of following the interface between the layers.

Investigating Some Technical Issues on Cohesive Zone Modeling of Fracture

NASA Technical Reports Server (NTRS)

Wang, John T.

2011-01-01

This study investigates some technical issues related to the use of cohesive zone models (CZMs) in modeling fracture processes. These issues include: why cohesive laws of different shapes can produce similar fracture predictions; under what conditions CZM predictions have a high degree of agreement with linear elastic fracture mechanics (LEFM) analysis results; when the shape of cohesive laws becomes important in the fracture predictions; and why the opening profile along the cohesive zone length needs to be accurately predicted. Two cohesive models were used in this study to address these technical issues. They are the linear softening cohesive model and the Dugdale perfectly plastic cohesive model. Each cohesive model constitutes five cohesive laws of different maximum tractions. All cohesive laws have the same cohesive work rate (CWR) which is defined by the area under the traction-separation curve. The effects of the maximum traction on the cohesive zone length and the critical remote applied stress are investigated for both models. For a CZM to predict a fracture load similar to that obtained by an LEFM analysis, the cohesive zone length needs to be much smaller than the crack length, which reflects the small scale yielding condition requirement for LEFM analysis to be valid. For large-scale cohesive zone cases, the predicted critical remote applied stresses depend on the shape of cohesive models used and can significantly deviate from LEFM results. Furthermore, this study also reveals the importance of accurately predicting the cohesive zone profile in determining the critical remote applied load.

It is Time to Rescind Don’t Ask, Don’t Tell

DTIC Science & Technology

2009-04-02

cohesion and that in turn would affect accomplishing the mission. A study done at UC, Davis, makes a distinction between social cohesion and task...cohesion.22 Social cohesion is the nature and quality of emotional bonds of friendship, closeness, etc. and task cohesion is a shared commitment among...studies of cohesion and performance it is task cohesion, not social cohesion or group pride that drives group performance. Professor MacCoun also

The Three-Dimensional (3D) Numerical Stability Analysis of Hyttemalmen Open-Pit

NASA Astrophysics Data System (ADS)

Cała, Marek; Kowalski, Michał; Stopkowicz, Agnieszka

2014-10-01

The purpose of this paper was to perform the 3D numerical calculations allowing slope stability analysis of Hyttemalmen open pit (location Kirkenes, Finnmark Province, Norway). After a ramp rock slide, which took place in December 2010, as well as some other small-scale rock slope stability problems, it proved necessary to perform a serious stability analyses. The Hyttemalmen open pit was designed with a depth up to 100 m, a bench height of 24 m and a ramp width of 10 m. The rock formation in the iron mining district of Kirkenes is called the Bjornevaten Group. This is the most structurally complicated area connected with tectonic process such as folding, faults and metamorphosis. The Bjornevaten Group is a volcano-sedimentary sequence. Rock slope stability depends on the mechanical properties of the rock, hydro-geological conditions, slope topography, joint set systems and seismic activity. However, rock slope stability is mainly connected with joint sets. Joints, or general discontinuities, are regarded as weak planes within rock which have strength reducing consequences with regard to rock strength. Discontinuities within the rock mass lead to very low tensile strength. Several simulations were performed utilising the RocLab (2007) software to estimate the gneiss cohesion for slopes of different height. The RocLab code is dedicated to estimate rock mass strength using the Hoek-Brown failure criterion. Utilising both the GSI index and the Hoek-Brown strength criterion the equivalent Mohr-Coulomb parameters (cohesion and angle of internal friction) can be calculated. The results of 3D numerical calculations (with FLA3D code) show that it is necessary to redesign the slope-bench system in the Hyttemalmen open pit. Changing slope inclination for lower stages is recommended. The minimum factor of safety should be equal 1.3. At the final planned stage of excavation, the factor of safety drops to 1.06 with failure surface ranging through all of the slopes. In the case of a slope angle 70° for lower stages, FS = 1.26, which is not enough to provide slope stability. Another series of calculations were therefore performed taking water table lowering into consideration, which increases the global safety factor. It was finally evaluated, that for a water table level of 72 m the factor of safety equals 1.3, which is enough to assure global open-pit stability.

Relative depths of simple craters and the nature of the lunar regolith

NASA Astrophysics Data System (ADS)

Stopar, Julie D.; Robinson, Mark S.; Barnouin, Olivier S.; McEwen, Alfred S.; Speyerer, Emerson J.; Henriksen, Megan R.; Sutton, Sarah S.

2017-12-01

We assessed the morphologies of more than 930 simple impact craters (diameters 40 m-10 km) on the Moon using digital terrain models (DTMs) of a variety of terrains in order to characterize the variability of fresh crater morphology as a function of crater diameter. From Lunar Reconnaissance Orbiter Camera (LROC) Narrow Angle Camera (NAC) DTMs, we determined depth-to-diameter (d/D) ratios for an extremely fresh set of these craters with diameters less than 400 m and found that their d/D ratios range from 0.11 to 0.17. Using both NAC and Kaguya Terrain Camera DTMs, we also determined the d/D ratios for the set of fresh simple craters larger than 400 m in diameter. The d/D ratios of these larger craters are typically near 0.21, as expected of gravity-dominated crater excavation. Fresh craters less than ∼400 m in diameter, on the other hand, exhibit significantly lower d/D ratios. Various possible factors affect the morphologies and relative depths (d/D ratios) of small strength-dominated craters, including impactor and target properties (e.g., effective strength, strength contrasts, porosity, pre-existing weaknesses), impact angle and velocity, and degradation state. While impact conditions resulting from secondary impacts can also affect crater morphologies, we found that d/D ratio alone was not a unique discriminator of small secondary craters. To investigate the relative influences of degradation and target properties on the d/D ratios of small strength-dominated craters, we examined a subset of fresh craters located on the geologically young rim deposits of Tycho crater. These craters are deeper and steeper than other craters of similar diameter and degradation state, consistent with their relative freshness and formation in the relatively coherent, melt-rich deposits in this region. The d/D ratios of globally distributed small craters of similar degradation state and size range, on the other hand, are relatively shallow with lower average wall slopes, consistent with crater excavation in a weak or poorly cohesive layer. The widespread predominance of these small, shallow craters is consistent with the pervasive, poorly cohesive upper regolith.

Spacing of Imbricated Thrust Faults and the Strength of Thrust-Belts and Accretionary Wedges

NASA Astrophysics Data System (ADS)

Ito, G.; Regensburger, P. V.; Moore, G. F.

2017-12-01

The pattern of imbricated thrust blocks is a prominent characteristic of the large-scale structure of thrust-belts and accretionary wedges around the world. Mechanical models of these systems have a rich history from laboratory analogs, and more recently from computational simulations, most of which, qualitatively reproduce the regular patterns of imbricated thrusts seen in nature. Despite the prevalence of these patterns in nature and in models, our knowledge of what controls the spacing of the thrusts remains immature at best. We tackle this problem using a finite difference, particle-in-cell method that simulates visco-elastic-plastic deformation with a Mohr-Coulomb brittle failure criterion. The model simulates a horizontal base that moves toward a rigid vertical backstop, carrying with it an overlying layer of crust. The crustal layer has a greater frictional strength than the base, is cohesive, and is initially uniform in thickness. As the layer contracts, a series of thrust blocks immerge sequentially and form a wedge having a mean taper consistent with that predicted by a noncohesive, critical Coulomb wedge. The widths of the thrust blocks (or spacing between adjacent thrusts) are greatest at the front of the wedge, tend to decrease with continued contraction, and then tend toward a pseudo-steady, minimum width. Numerous experiments show that the characteristic spacing of thrusts increases with the brittle strength of the wedge material (cohesion + friction) and decreases with increasing basal friction for low (<8°) taper angles. These relations are consistent with predictions of the elastic stresses forward of the frontal thrust and at what distance the differential stress exceeds the brittle threshold to form a new frontal thrust. Hence the characteristic spacing of the thrusts across the whole wedge is largely inherited at the very front of the wedge. Our aim is to develop scaling laws that will illuminate the basic physical processes controlling systems, as well as allow researchers to use observations of thrust spacing as an independent constraint on the brittle strength of wedges as well as their bases.

Crustal strength anisotropy influences landscape form and longevity

NASA Astrophysics Data System (ADS)

Roy, S. G.; Koons, P. O.; Upton, P.; Tucker, G. E.

2013-12-01

Lithospheric deformation is increasingly recognized as integral to landscape evolution. Here we employ a coupled orogenic and landscape model to test the hypothesis that strain-induced crustal failure exerts the dominant control on rates and patterns of orogenic landscape evolution. We assume that erodibility is inversely proportional to cohesion for bedrock rivers host to bedload abrasion. Crustal failure can potentially reduce cohesion by several orders of magnitude along meter scale planar fault zones. The strain-induced cohesion field is generated by use of a strain softening upper crustal rheology in our orogenic model. Based on the results of our coupled model, we predict that topographic anisotropy found in natural orogens is largely a consequence of strain-induced anisotropy in the near surface strength field. The lifespan and geometry of mountain ranges are strongly sensitive to 1) the acute division in erodibility values between the damaged fault zones and the surrounding intact rock and 2) the fault zone orientations for a given tectonic regime. The large division in erodibility between damaged and intact rock combined with the dependence on fault zone orientation provides a spectrum of rates at which a landscape will respond to tectonic or climatic perturbations. Knickpoint migration is about an order of magnitude faster along the exposed cores of fault zones when compared to rates in intact rock, and migration rate increases with fault dip. The contrast in relative erosion rate confines much of the early stage fluvial erosion and establishes a major drainage network that reflects the orientations of exposed fault zones. Slower erosion into the surrounding intact rock typically creates small tributaries that link orthogonally to the structurally confined channels. The large divide in fluvial erosion rate permits the long term persistence of the tectonic signal in the landscape and partly contributes to orogen longevity. Landscape morphology and channel tortuosity together provide critical information on the orientation and spatial distribution of fault damage and the relevant tectonic regime. Our landscape evolution models express similar mechanisms and produce drainage network patterns analogous to those seen in the Southern Alps of New Zealand and the Himalayan Eastern Syntaxis, both centers of active lithospheric deformation.

Seasonal variations in composite riverbank stability in the Lower Jingjiang Reach, China

NASA Astrophysics Data System (ADS)

Xia, Junqiang; Zong, Quanli; Deng, Shanshan; Xu, Quanxi; Lu, Jinyou

2014-11-01

Bank erosion is a key process in a fluvial system in the context of river dynamics and geomorphology. Since the operation of the Three Gorges Project (TGP), the Lower Jingjiang Reach (LJR) below the dam has experienced continuous channel degradation, with the phenomenon of bank erosion occurring frequently in local reaches. Therefore it is necessary to quantitatively investigate seasonal variations in the stability of composite riverbanks along the reach in order to better understand the fluvial processes in the reach. Laboratory tests were conducted for the sampled soils at six riverbanks during a field survey, with various bank soil properties being presented for the first time. These test results show that: the cohesive bank soils are relatively loose due to the high water contents of 28.5-40.0% and the low dry densities of 1.31-1.47 tonnes/m3; and the cohesion or angle of internal friction generally decreases with an increase in water content of the cohesive soil. Based on the measured cross-sectional profiles and interpolated hydrological data, the near-bank hydrodynamic conditions and soil parameters of two typical composite riverbanks were then determined during the 2007 hydrological year. An improved method was proposed for calculating the stability at the mode of cantilever failure for the overhanging block of a composite riverbank, and the stability degrees of these two riverbanks were calculated at different stages. These results reveal that: (i) the incipient velocity of the non-cohesive lower bank had a magnitude of 0.4 m/s, less than the mean near-bank velocity of about 1.0 m/s, which led to intensive basal erosion especially during the flood season; (ii) the cohesive upper bank before failure had sufficient strength to resist direct fluvial erosion, but the failed soil mass deposited in the near-bank zone was disintegrated easily with the submerged immersion and was then transported downstream by fluvial entrainment; (iii) the degree of bank stability was relatively lower during the flood season, caused by the integrated effects of a process of severe basal erosion and a lower unit weight of 8.6 kN/m3 for the submerged soil; and (iv) the degree of bank stability was lowest at the recession stage, which was caused by the vanishing of the hydrostatic confining pressure and the larger unit weight of 18.0 kN/m3 for the saturated cohesive soil, because of a rapid drawdown in the in-channel water levels with the TGP operation.

Some physical and mechanical properties of recycled polyurethane foam blends

NASA Astrophysics Data System (ADS)

Bledzki, A. K.; Zicans, J.; Merijs Meri, R.; Kardasz, D.

2008-09-01

Blends of secondary rigid polyurethane foams (RPUFs) with soft polyurethane foams (SPUFs) were investigated. The effect of SPUF content and its chemical nature on some physical and mechanical properties of the blends was evaluated. Owing to the stronger intermolecular interaction and higher values of cohesion energy, the blends of RPUFs with polyester SPUFs showed higher mechanical properties than those with polyether SPUFs. The density, hardness, ultimate strength, and the tensile, shear, and flexural moduli increased, while the impact toughness, ultimate elongation, and damping characteristics decreased with increasing RPUF content in the blends.

A critical study of the role of the surface oxide layer in titanium bonding

NASA Technical Reports Server (NTRS)

Dias, S.; Wightman, J. P.

1983-01-01

Scanning electron microscope/X-ray photoelectron spectroscopy (SEM/XPS) analysis of fractured adhesively bonded Ti 6-4 samples is discussed. The text adhesives incuded NR 056X polyimide, polypheylquinoxaline (PPQ), and LARC-13 polyimide. Differentiation between cohesive and interfacial failure was based on the absence of presence of a Ti 2p XPS photopeak. In addition, the surface oxide layer on Ti-(6A1-4V) adherends is characterized and bond strength and durability are addressed. Bond durability in various environmental conditions is discussed.

Martian physical properties experiments: The Viking Mars Lander

USGS Publications Warehouse

Shorthill, R.W.; Hutton, R.E.; Moore, H.J.; Scott, R.F.

1972-01-01

Current data indicate that Mars, like the Earth and Moon, will have a soil-like layer. An understanding of this soil-like layer is an essential ingredient in understanding the Martian ecology. The Viking Lander and its subsystems will be used in a manner similar to that used by Sue Surveyor program to define properties of the Martian "soil". Data for estimates of bearing strength, cohesion, angle of internal friction, porosity, grain size, adhesion, thermal inertia, dielectric constants, and homogeneity of the Martian surface materials will be collected. ?? 1972.

Lunar Surface Material - Spacecraft Measurements of Density and Strength

NASA Technical Reports Server (NTRS)

Jaffe, L. D.

1969-01-01

The relation of the density of the lunar surface layer to depth is probably best determined from spacecraft measurements of the bearing capacity as a function of depth. A comparison of these values with laboratory measurements of the bearing capacity of low-cohesion particulate materials as a function of the percentage of solid indicates that the bulk density at the lunar surface is about 1.1 grams per cubic centimeter and that it increases nearly linearly to about 1.6 grams per cubic centimeter at a depth of 5 centimeters.

Cohesion as a Command Emphasis Item

DTIC Science & Technology

2010-03-01

of the notion of cohesion— social cohesion . Social cohesion is the affective bonding between members; or to expound further, the interpersonal...team to achieve that goal. 3 Members with high task cohesion do not necessarily share high social cohesion . The reason this distinction is...important is due to the fact that when thinking in terms of cohesion, most leaders think of it in terms of social cohesion . Unfortunately, studies of the

Implications of Integrating Women into the Marine Corps Infantry

DTIC Science & Technology

2015-12-01

findings and implications from our study. Research on Cohesion In general, prior research demonstrates that more cohesive groups perform better than less...woman in the group ,1 but the optimal proportion of women for group cohesion is not clear from the existing research . Finally, there are cohesion...that integration might have on group cohesion. This is for good reason: research on group cohesion has demonstrated that cohesion has a direct rela

Microscale characterization of metallic coatings for a high strength high conductivity copper alloy

NASA Astrophysics Data System (ADS)

Jain, Piyush

NiCrAlY overlay coatings are being considered by NASA's Glenn Research Center to prevent blanching and reduce thermo-mechanical fatigue of rocket engine combustion chamber liners made of GRCop-84 (Cu-8%Cr-4%Nb) for reusable launch vehicles (RLVs). However, their successful application depends upon their integrity to the GRCop-84 during multiple firings of rocket engines. This study focuses on determining the adhesion of NiCrAlY coatings and their microstructural stability on GRCop-84 as a function of thermal cycling. Specimens were prepared by depositing NiCrAlY top coat on GRCop-84 by vacuum plasma spaying with a thin layer of Cu-26Cr as a bond coat. A thermal cycling rig was built to thermally cycle the NiCrAlY/Cu-26Cr/GRCop-84 specimens from RT to 600°C in an argon environment, with 10 minutes hold at 600°C, and 4 minutes hold at RT. Samples were cut from the coupons in as-received condition (AR), after 100 thermal cycles (TC-100), and after 300 thermal cycles (TC-300) for characterization. A newly developed interfacial microsample testing technique was employed to determine the adhesion of the coatings on GRCop-84, where bowtie shaped microsamples having interfaces normal to the tensile axis were tested. Interfacial microsamples of NiCrAlY/Cu-26Cr/GRCop-84 in all the conditions (AR, TC-100, and TC-300) failed cohesively in the substrate at a UTS of 380+/-5 MPa and their interfaces remained intact. The microstructural characterization revealed that microstructure of the NiCrAlY/Cu-26Cr/GRCop-84 specimens does not degrade as a function of thermal cycling. Constitutive properties of NiCrAlY, Cu-26Cr, and GRCop-84 were measured by testing monolithic samples and were used to build the finite element model (FEM) of the interfacial microsamples. The FE model analyzed the local stress-strain in the interfacial microsamples during the testing and confirmed the strength of the interfaces to be higher than 380+/-5 MPa. Depleted zones, devoid of Cr2Nb particles, were observed in the substrate near the interface, which has been attributed to uncontrolled processing parameters during the coating deposition. The interfacial microsamples containing depleted zones, failed at 335+/-25 MPa in AR condition exhibiting cohesive-adhesive failure, and at 360+/-15 MPa in TC-300 condition exhibiting adhesive failure. All these results suggested that the presence of depleted zone decreases the adhesion of the coating and should be avoided in future coatings deposition. Adhesion of two top coats, NiCrAlY (with the Cu-26Cr bond coat) and the Cu-26Cr (without any bond coat), were found to be lower on the grit blasted GRCop-84 than on the polished GRCop-84. The adhesion of both the top coats on polished GRCop-84 was measured to be 380+/-5 MPa with cohesive failure in the substrate, while the adhesion of NiCrAlY top coat on the grit blasted GRCop-84 was measured to be 142+/-35 MPa with cohesive failure in the Cu-26Cr bond coat, and the adhesion of Cu-26Cr top coat on the grit blasted GRCop-84 was measured to be 360+/-25 MPa with cohesive failure in the Cu-26Cr top coat. The microstructural characterization revealed that the reason of lower strength of top coats on the grit blasted GRCop-84 was the porosity present in the coatings on the grit blasted GRCop-84, while the coatings on the polished GRCop-84 did not have any measurable porosity.

Key Skills for Science Learning: The Importance of Text Cohesion and Reading Ability

ERIC Educational Resources Information Center

Hall, Sophie Susannah; Maltby, John; Filik, Ruth; Paterson, Kevin B.

2016-01-01

To explore the importance of text cohesion, we conducted two experiments. We measured online (reading times) and offline (comprehension accuracy) processes for texts that were high and low cohesion. In study one (n?=?60), we manipulated referential cohesion using noun repetition (high cohesion) and synonymy (low cohesion). Students showed enhanced…

Social Cohesion as the Goal: Can Social Cohesion Be Directly Pursued?

ERIC Educational Resources Information Center

Koonce, Kelly A.

2011-01-01

This article establishes an understanding of social cohesion in general and discusses organizations and activities that are known to promote social cohesion before introducing organizations that claim to work toward social cohesion as one of their main priorities. The Council of Europe's Directorate General of Social Cohesion represents a…

Two-year interfacial bond durability and nanoleakage of repaired silorane-based resin composite.

PubMed

Mobarak, E; El-Deeb, H

2013-01-01

To investigate the effect of silane primer application, intermediate adhesive agent/repair composite, and storage period on the interfacial microtensile bond strength (μTBS) of repaired silorane-based resin composite compared with unrepaired composites and on the nanoleakage. Forty-eight 1-month-old substrate specimens from Filtek P90 were roughened, etched, and distributed over two groups (n=24) based on receiving silane (Clearfil Ceramic Primer) or not. Then, half of the specimens (n=12) were repaired with P90 System Adhesive/Filtek P90 and the other half with Adper Scotchbond Multipurpose adhesive/Filtek Z250 resin composite. Within each repair category, repaired specimens were stored in artificial saliva at 37°C for either 24 hours (n=6) or two years before being serially sectioned into sticks (0.6 ± 0.01 mm(2)). From each specimen, two sticks were prepared for nanoleakage determination and four sticks were used for μTBS testing. Additional unrepaired specimens from each composite (n=12) were made to determine the cohesive strength at 24 hours and two years. Mean μTBS were calculated and statistically analyzed. Modes of failure were also determined. General linear model analysis revealed no significant effect for the silane priming, intermediate adhesive agent/repair composite, and storage period or for their interactions on the μTBS values of the repaired specimens. There was no significant difference between the cohesive strength of Filtek P90 and Filtek Z250; both were significantly higher than all repaired categories. At 24 hours, nanoleakage was not detected when silorane-based composite was repaired with the same material. However, after two years, all repair categories showed nanoleakage. Silane application has no effect on μTBS and nanoleakage. Durability of the interfacial bond of repaired silorane-based resin composite appeared successful regardless of the chemistry of the intermediate adhesive agent/composite used for repair. However, nanoleakage was detected early when a different repair intermediate adhesive agent/composite was used.

[Effect of sintering gold paste coating on the bonding strength of pure titanium and three low-fusing porcelains].

PubMed

Zhang, Ya-li; Luo, Xiao-ping; Zhou, Li

2012-05-01

To study the effect of sintering gold paste coating of pure titanium on the adhesion of three porcelains following the protocol ISO 9693, and to investigate the titanium-porcelains interfaces. Sixty machined pure titanium samples were prepared in a rectangular shape according to ISO 9693 and divided equally into six groups. Half of the strips were coated with gold paste (Deckgold) and sintered. Three ultra-low-fusing dental porcelains (I: Initial Ti, S: Super porcelain Ti-22, T: TitanKeramik) were fused onto the titanium surfaces. A thin layer of bonding agent was only applied on the surfaces of uncoated gold specimens. The interface of the porcelain and titanium was observed with a field emission scanning electron microscope (FE-SEM) after metallographic preparation and sputtered with a very thin carbon layer of the embedded titanium-porcelain interface. After three-point bending test was performed, optical stereomicroscope was used to characterize the titanium-porcelains adhesion and determine the mode of failure. FE-SEM illustrated intermetallic compounds of Au-Ti formed with some visible microcracks in the gold layer and the interface of gold layer and ceramic. All the uncoated gold titanium-porcelain system showed predominately adhesive fracture at the titanium oxidation, whereas the failure modes in all gold coated systems were cohesive and adhesive, mainly cohesive. The three-point-bending test showed that the bonding strength of GS and GI groups [(37.08 ± 4.32) and (36.20 ± 2.40) MPa] were higher than those in uncoated groups [(31.56 ± 3.74) and (30.88 ± 2.60) MPa, P < 0.05], while no significant difference was found between T group and GT group (P > 0.05). The gold paste intermediate coatings can improve bond strengths of Super porcelain Ti-22 system and Initial Ti system, which have potential applications in clinical fields.

Quantifying intermolecular interactions of ionic liquids using cohesive energy densities.

PubMed

Lovelock, Kevin R J

2017-12-01

For ionic liquids (ILs), both the large number of possible cation + anion combinations and their ionic nature provide a unique challenge for understanding intermolecular interactions. Cohesive energy density, ced , is used to quantify the strength of intermolecular interactions for molecular liquids, and is determined using the enthalpy of vaporization. A critical analysis of the experimental challenges and data to obtain ced for ILs is provided. For ILs there are two methods to judge the strength of intermolecular interactions, due to the presence of multiple constituents in the vapour phase of ILs. Firstly, ced IP , where the ionic vapour constituent is neutral ion pairs, the major constituent of the IL vapour. Secondly, ced C+A , where the ionic vapour constituents are isolated ions. A ced IP dataset is presented for 64 ILs. For the first time an experimental ced C+A , a measure of the strength of the total intermolecular interaction for an IL, is presented. ced C+A is significantly larger for ILs than ced for most molecular liquids, reflecting the need to break all of the relatively strong electrostatic interactions present in ILs. However, the van der Waals interactions contribute significantly to IL volatility due to the very strong electrostatic interaction in the neutral ion pair ionic vapour. An excellent linear correlation is found between ced IP and the inverse of the molecular volume. A good linear correlation is found between IL ced IP and IL Gordon parameter (which are dependent primarily on surface tension). ced values obtained through indirect methods gave similar magnitude values to ced IP . These findings show that ced IP is very important for understanding IL intermolecular interactions, in spite of ced IP not being a measure of the total intermolecular interactions of an IL. In the outlook section, remaining challenges for understanding IL intermolecular interactions are outlined.

Quantifying intermolecular interactions of ionic liquids using cohesive energy densities

PubMed Central

2017-01-01

For ionic liquids (ILs), both the large number of possible cation + anion combinations and their ionic nature provide a unique challenge for understanding intermolecular interactions. Cohesive energy density, ced, is used to quantify the strength of intermolecular interactions for molecular liquids, and is determined using the enthalpy of vaporization. A critical analysis of the experimental challenges and data to obtain ced for ILs is provided. For ILs there are two methods to judge the strength of intermolecular interactions, due to the presence of multiple constituents in the vapour phase of ILs. Firstly, cedIP, where the ionic vapour constituent is neutral ion pairs, the major constituent of the IL vapour. Secondly, cedC+A, where the ionic vapour constituents are isolated ions. A cedIP dataset is presented for 64 ILs. For the first time an experimental cedC+A, a measure of the strength of the total intermolecular interaction for an IL, is presented. cedC+A is significantly larger for ILs than ced for most molecular liquids, reflecting the need to break all of the relatively strong electrostatic interactions present in ILs. However, the van der Waals interactions contribute significantly to IL volatility due to the very strong electrostatic interaction in the neutral ion pair ionic vapour. An excellent linear correlation is found between cedIP and the inverse of the molecular volume. A good linear correlation is found between IL cedIP and IL Gordon parameter (which are dependent primarily on surface tension). ced values obtained through indirect methods gave similar magnitude values to cedIP. These findings show that cedIP is very important for understanding IL intermolecular interactions, in spite of cedIP not being a measure of the total intermolecular interactions of an IL. In the outlook section, remaining challenges for understanding IL intermolecular interactions are outlined. PMID:29308254

R&D in Poland: Is the Country Close to a Knowledge-Driven Economy?

NASA Astrophysics Data System (ADS)

Chybowska, Dorota; Chybowski, Leszek; Souchkov, Valeri

2018-06-01

Poland has a strong ambition to evolve rapidly into a knowledge-driven economy. Since 2004, it has been the largest beneficiary of European Union cohesion policy funds among all member states. Between 2007 and 2013, Poland was allocated approximately EUR 67 billion, whereas for 2014-2020 the EU budget earmarked EUR 82.5 billion for Polish cohesion policy. This means that in the coming years, Poland's R&D intensity will grow. But the question remains: is 27 years of free market economy enough to enable a country's economy to become knowledge-based ? This paper offers an analysis of Polish R&D expenditures and investments in terms of their sources (business, government or higher education sectors), types (European Union or state aid) and areas of support (infrastructure, education or innovation). It also characterises the Polish R&D market with its strengths and weaknesses. Then, it examines the process of technology transfer in Poland, comparing it to best practice. Finally, the paper lays out the barriers to effective commercialisation that need to be overcome, and attempts to answer the question raised in its title.

Density functional studies of the defect-induced electronic structure modifications in bilayer boronitrene

NASA Astrophysics Data System (ADS)

Ukpong, A. M.; Chetty, N.

2012-05-01

The van der Waals interaction-corrected density functional theory is used in this study to investigate the formation, energetic stability, and inter-layer cohesion in bilayer hexagonal boronitrene. The effect of inter-layer separation on the electronic structure is systematically investigated. The formation and energetic stability of intrinsic defects are also investigated at the equilibrium inter-layer separation. It is found that nonstoichiometric defects, and their complexes, that induce excess nitrogen or excess boron, in each case, are relatively more stable in the atmosphere that corresponds to the excess atomic species. The modifications of the electronic structure due to formation of complexes are also investigated. It is shown that van der Waals density functional theory gives an improved description of the cohesive properties but not the electronic structure in bilayer boronitrene compared to other functionals. We identify energetically favourable topological defects that retain the energy gap in the electronic structure, and discuss their implications for band gap engineering in low-n layer boronitrene insulators. The relative strengths and weaknesses of the functionals in predicting the properties of bilayer boronitrene are also discussed.

Surface topography and bond strengths of feldspathic porcelain prepared using various sandblasting pressures.

PubMed

Moravej-Salehi, Elham; Moravej-Salehi, Elahe; Valian, Azam

2016-11-01

The purpose of this study was to determine the bond strength of composite resin to feldspathic porcelain and its surface topography after sandblasting at different pressures. In this in vitro study, 68 porcelain disks were fabricated and randomly divided into four groups of 17. The porcelain surface in group 1 was etched with hydrofluoric acid. Groups 2, 3, and 4 were sandblasted at 2, 3 and 4 bars pressure, respectively. Surface topography of seven samples in each of the four groups was examined by a scanning electron microscope (SEM). The remaining 40 samples received the same silane agent, bonding agent, and composite resin and they were then subjected to 5000 thermal cycles and evaluated for shear bond strength. Data were analyzed using one-way anova. The mode of failure was determined using stereomicroscope and SEM. The highest shear bond strength was seen in group 4. however, statistically significant differences were not seen between the groups (P = 0.780). The most common mode of failure was cohesive in porcelain. The SEM showed different patterns of hydrofluoric acid etching and sandblasting. Increasing the sandblasting pressure increased the surface roughness of feldspathic porcelain but no difference in bond strength occurred. © 2015 Wiley Publishing Asia Pty Ltd.

Static Strength of Adhesively-bonded Woven Fabric Kenaf Composite Plates

NASA Astrophysics Data System (ADS)

Hilton, Ahmad; Lee, Sim Yee; Supar, Khairi

2017-06-01

Natural fibers are potentially used as reinforcing materials and combined with epoxy resin as matrix system to form a superior specific strength (or stiffness) materials known as composite materials. The advantages of implementing natural fibers such as kenaf fibers are renewable, less hazardous during fabrication and handling process; and relatively cheap compared to synthetic fibers. The aim of current work is to conduct a parametric study on static strength of adhesively bonded woven fabric kenaf composite plates. Fabrication of composite panels were conducted using hand lay-up techniques, with variation of stacking sequence, over-lap length, joint types and lay-up types as identified in testing series. Quasi-static testing was carried out using mechanical testing following code of practice. Load-displacement profiles were analyzed to study its structural response prior to ultimate failures. It was found that cross-ply lay-up demonstrates better static strength compared to quasi-isotropic lay-up counterparts due to larger volume of 0° plies exhibited in cross-ply lay-up. Consequently, larger overlap length gives better joining strength, as expected, however this promotes to weight penalty in the joining structure. Most samples showed failures within adhesive region known as cohesive failure modes, however, few sample demonstrated interface failure. Good correlations of parametric study were found and discussed in the respective section.

On the Interplay Between Adhesion Strength and Tensile Properties of Thermal Spray Coated Laminates—Part I: High Velocity Thermal Spray Coatings

NASA Astrophysics Data System (ADS)

Luo, Xiaotao; Smith, Gregory M.; Sampath, Sanjay

2018-02-01

Adhesion of thermal spray (TS) coatings is an important system level property in coating design and application. Adhesive-based pull testing (ASTM C633) has long been used to evaluate coating/substrate bonding. However, this approach is not always suitable for high velocity spray coatings, for example, where adhesion strengths are routinely greater than the strength of the adhesive bonding agent used in the testing. In this work, a new approach has been proposed to evaluate the adhesion of TS coatings. A systematic investigation of the effects of substrate roughness on both the uniaxial tensile yield strength and traditional bond pull adhesive strength of HVOF Ni and Ni-5wt.%Al, as well as cold-sprayed Ni-coated laminates revealed a strong correlation between these two test methodologies for the respective materials and processes. This approach allows measurement of the adhesion response even where the adhesive method is not applicable, overcoming many of the issues in the traditional ASTM C633. Analysis of cracking patterns of the coatings after 10.5% strain was used to assess the adhesion and cohesion properties. The mechanisms which determine the load transfer between the substrate and the coating are also briefly discussed.

The effect of thermocycling on tensile bond strength of two soft liners.

PubMed

Geramipanah, Farideh; Ghandari, Masoumeh; Zeighami, Somayeh

2013-09-01

Failure of soft liners depends mostly on separation from the denture base resin; therefore measurement of the bond strength is very important. The purpose of this study was to compare the tensile bond strength of two soft liners (Acropars, Molloplast-B) to denture base resin before and after thermocycling. Twenty specimens fromeach of the two different soft liners were processed according to the manufacturer's instructions between two polymethyl methacrylate (PMMA) sheets. Ten specimens in each group were maintained in 37°C water for 24 hours and 10 were thermocycled (5000 cycles) among baths of 5° and 55°C. The tensile bond strength was measured using a universal testing machine at a crosshead speed of 5 mm/min. Mode of failure was determined with SEM (magnification ×30). Two-way ANOVA was used to analyze the data. The mean and standard deviation of tensile bond strength of Acropars and Molloplast-B before thermocycling were 6.59±1.85 and1.51±0.22 MPa, respectively and 5.89±1.52 and1.37±0.18 MPa, respectively after thermocycling. There was no significant difference before and after thermocycling. Mode of failure in Acropars and Molloplast-B were adhesive and cohesive, respectivley. The bond strength of Acropars was significantly higher than Molloplast-B (P<0.05).

Evaluation of EA-934NA with 2.5 percent Cab-O-Sil

NASA Technical Reports Server (NTRS)

Caldwell, Gordon A.

1990-01-01

Currently, Hysol adhesive EA-934NA is used to bond the Field Joint Protection System on the Shuttle rocket motors at Kennedy Space Center. However, due to processing problems, an adhesive with a higher viscosity is needed to alleviate these difficulties. One possible solution is to add Cab-O-Sil to the current adhesive. The adhesive strength and bond strengths that can be obtained when 2.5 percent Cab-O-Sil is added to adhesive EA-934NA are examined and tested over a range of test temperatures from -20 to 300 F. Tensile adhesion button and lap shear specimens were bonded to D6AC steel and uniaxial tensile specimens (testing for strength, initial tangent modulus, elongation and Poisson's ratio) were prepared using Hysol adhesive EA-934NA with 2.5 percent Cab-O-Sil added. These specimens were tested at -20, 20, 75, 100, 125, 150, 200, 250, and 300 F, respectively. Additional tensile adhesion button specimens bonding Rust-Oleum primed and painted D6AC steel to itself and to cork using adhesive EA-934NA with 2.5 percent Cab-O-Sil added were tested at 20, 75, 125, 200, and 300 F, respectively. Results generally show decreasing strength values with increasing test temperatures. The bond strengths obtained using cork as a substrate were totally dependent on the cohesive strength of the cork.

Evaluation of metal bond strength to dentin and enamel using different adhesives and surface treatments.

PubMed

Dundar, Mine; Gungor, Mehmet Ali; Cal, Ebru; Darcan, Alev; Erdem, Adalet

2007-01-01

Because adherence of base metal alloys is important for the long-term clinical success of adhesive fixed partial dentures, it has been necessary to improve adhesion to metal substrate by using different surface treatments. This study used different surface conditioning methods and two different luting resins to evaluate the shear bond strength of base metal alloys to dentin and enamel. Sixty noncarious freshly extracted human teeth were mounted in a plastic holder filled with autopolymerized acrylic resin. After the roots were removed and 30 flat enamel and 30 flat dentin surfaces were exposed, the specimens were divided randomly into two main luting cement groups. Sixty nickel chromium (NiCr) metal specimens were fabricated and subjected to three different surface conditioning procedures: sandblasting with 50 microm aluminum oxide, tribochemical silica coating, and a combination of the two. Scanning electron mircoscopy (SEM) evaluations revealed mainly cohesive failures. Self-cure adhesive resulted in higher bond strengths to dental substrates. Higher bond strengths were achieved through a combination of sandblasting and tribochemical silica coating; however, further clinical research is required. A surface treatment that combines sandblasting with tribochemical silica coating can achieve a more effective bond for adhesive restorations with metal substrates.

Statistical Characterization of the Mechanical Parameters of Intact Rock Under Triaxial Compression: An Experimental Proof of the Jinping Marble

NASA Astrophysics Data System (ADS)

Jiang, Quan; Zhong, Shan; Cui, Jie; Feng, Xia-Ting; Song, Leibo

2016-12-01

We investigated the statistical characteristics and probability distribution of the mechanical parameters of natural rock using triaxial compression tests. Twenty cores of Jinping marble were tested under each different levels of confining stress (i.e., 5, 10, 20, 30, and 40 MPa). From these full stress-strain data, we summarized the numerical characteristics and determined the probability distribution form of several important mechanical parameters, including deformational parameters, characteristic strength, characteristic strains, and failure angle. The statistical proofs relating to the mechanical parameters of rock presented new information about the marble's probabilistic distribution characteristics. The normal and log-normal distributions were appropriate for describing random strengths of rock; the coefficients of variation of the peak strengths had no relationship to the confining stress; the only acceptable random distribution for both Young's elastic modulus and Poisson's ratio was the log-normal function; and the cohesive strength had a different probability distribution pattern than the frictional angle. The triaxial tests and statistical analysis also provided experimental evidence for deciding the minimum reliable number of experimental sample and for picking appropriate parameter distributions to use in reliability calculations for rock engineering.

Understanding the Effects of Electrode Formulation on the Mechanical Strength of Composite Electrodes for Flexible Batteries.

PubMed

Gaikwad, Abhinav M; Arias, Ana Claudia

2017-02-22

Flexible lithium-ion batteries are necessary for powering the next generation of wearable electronic devices. In most designs, the mechanical flexibility of the battery is improved by reducing the thickness of the active layers, which in turn reduces the areal capacity and energy density of the battery. The performance of a battery depends on the electrode composition, and in most flexible batteries, standard electrode formulation is used, which is not suitable for flexing. Even with considerable efforts made toward the development of flexible lithium-ion batteries, the formulation of the electrodes has received very little attention. In this study, we investigate the relation between the electrode formulation and the mechanical strength of the electrodes. Peel and drag tests are used to compare the adhesion and cohesion strength of the electrodes. The strength of an electrode is sensitive to the particle size and the choice of polymeric binder. By optimizing the electrode composition, we were able to fabricate a high areal capacity (∼2 mAh/cm 2 ) flexible lithium-ion battery with conventional metal-based current collectors that shows superior electrochemical and mechanical performance in comparison to that of batteries with standard composition.

Strengths of OPEC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adelman, M.A.

The major distinction of the Organization of Petroleum Exporting Countries is obvious even to the casual observer: the nations composing it constitute the greatest monopoly in history; its tribute now is over $100 billion a year. For the immediate future, OPEC's elements of strength look more important than its elements of weakness. The cartel will not soon disappear. The forces acting against the cartel are subsumed in the fact of excess capacity. This is the traditional nemesis of cartels, since it puts in motion the sequence of small price reductions by some sellers to gain additional sales volume, then competitivemore » or matching reductions. To preserve the cartel, each member must avoid acting for his own independent good, and must do what is best for the group as a whole. The greater the temptation to act independently the greater the fear of others' independent action, and the higher the probability of severe erosion or breakdown. So the fate of the cartel depends essentially on the strength of exogenous factors, demand and uncontrolled supply, versus the strength of an endogenous factor, the cohesion of the group. All too often either one of these factors is treated in isolation as though the other were not there.« less

Effects of silver nanoparticles on the bonding of three adhesive systems to fluorotic enamel.

PubMed

Torres-Méndez, Fernando; Martinez-Castañon, Gabriel-Alejandro; Torres-Gallegos, Iranzihuatl; Zavala-Alonso, Norma-Verónica; Patiño-Marin, Nuria; Niño-Martínez, Nereyda; Ruiz, Facundo

2017-05-31

The objective was to evaluate the effect of adding silver nanoparticles into three commercial adhesive systems (Excite™, Adper Prompt L-Pop™ and AdheSE™). Nanoparticles were prepared by a chemical method then mixed with the commercial adhesive systems. This was later applied to the fluorotic enamel, and then micro-tensile bond strength, contact angle measurements and scanning electron microscopy observations were conducted. The commercial adhesive systems achieved the lowest micro-tensile bond strength (Excite™: 11.0±2.1, Adper Prompt L-Pop™: 14.0±5.4 and AdheSE™: 16.0±3.0 MPa) with the highest adhesive failure mode related with the highest contact angle (46.0±0.6º, 30.0±0.5º and 28.0±0.4º respectively). The bond strength achieved in all the experimental adhesive systems (19.0±5.4, 20.0±4.0 and 19.0±3.5 MPa respectively) was statistically higher (p<0.05) than the control and showed the highest cohesive failures related to the lowest contact angle. Adding silver nanoparticles in order to decrease the contact angle improve the adhesive system wetting and its bond strength.

Modeling the hydrological and mechanical effect of roots on shallow landslides

NASA Astrophysics Data System (ADS)

Arnone, E.; Caracciolo, D.; Noto, L. V.; Preti, F.; Bras, R. L.

2016-11-01

This study proposes a new methodology for estimating the additional shear strength (or cohesion) exerted by vegetation roots on slope stability analysis within a coupled hydrological-stability model. The mechanical root cohesion is estimated within a Fiber Bundle Model framework that allows for the evaluation of the root strength as a function of stress-strain relationships of populations of fibers. The use of such model requires the knowledge of the root architecture. A branching topology model based on Leonardo's rule is developed, providing an estimation of the amount of roots and the distribution of diameters with depth. The proposed methodology has been implemented into an existing distributed hydrological-stability model able to simulate the dynamics of factor of safety as a function of soil moisture dynamics. The model also accounts for the hydrological effects of vegetation, which reduces soil water content via root water uptake, thus increasing the stability. The entire methodology has been tested in a synthetic hillslope with two configurations of vegetation type, i.e., trees and shrubs, which have been compared to a configuration without vegetation. The vegetation has been characterized using roots data of two mediterranean plant species. The results demonstrate the capabilities of the topological model in accurately reproducing the observed root structure of the analyzed species. For the environmental setting modeled, the effects of root uptake might be more significant than the mechanical reinforcement; the additional resistance depends strictly on the vegetation root depth. Finally, for the simulated climatic environment, landslides are seasonal, in agreement with past observations.

Cross-linking by protein oxidation in the rapidly setting gel-based glues of slugs.

PubMed

Bradshaw, Andrew; Salt, Michael; Bell, Ashley; Zeitler, Matt; Litra, Noelle; Smith, Andrew M

2011-05-15

The terrestrial slug Arion subfuscus secretes a glue that is a dilute gel with remarkable adhesive and cohesive strength. The function of this glue depends on metals, raising the possibility that metal-catalyzed oxidation plays a role. The extent and time course of protein oxidation was measured by immunoblotting to detect the resulting carbonyl groups. Several proteins, particularly one with a relative molecular mass (M(r)) of 165 x 10³, were heavily oxidized. Of the proteins known to distinguish the glue from non-adhesive mucus, only specific size variants were oxidized. The oxidation appears to occur within the first few seconds of secretion. Although carbonyls were detected by 2,4-dinitrophenylhydrazine (DNPH) in denatured proteins, they were not easily detected in the native state. The presence of reversible cross-links derived from carbonyls was tested for by treatment with sodium borohydride, which would reduce uncross-linked carbonyls to alcohols, but stabilize imine bonds formed by carbonyls and thus lead to less soluble complexes. Consistent with imine bond formation, sodium borohydride led to a 20-35% decrease in the amount of soluble protein with a M(r) of 40-165 (x 10³) without changing the carbonyl content per protein. In contrast, the nucleophile hydroxylamine, which would competitively disrupt imine bonds, increased protein solubility in the glue. Finally, the primary amine groups on a protein with a M(r) of 15 x 10³ were not accessible to acid anhydrides. The results suggest that cross-links between aldehydes and primary amines contribute to the cohesive strength of the glue.

Cross-linking by protein oxidation in the rapidly setting gel-based glues of slugs

PubMed Central

Bradshaw, Andrew; Salt, Michael; Bell, Ashley; Zeitler, Matt; Litra, Noelle; Smith, Andrew M.

2011-01-01

SUMMARY The terrestrial slug Arion subfuscus secretes a glue that is a dilute gel with remarkable adhesive and cohesive strength. The function of this glue depends on metals, raising the possibility that metal-catalyzed oxidation plays a role. The extent and time course of protein oxidation was measured by immunoblotting to detect the resulting carbonyl groups. Several proteins, particularly one with a relative molecular mass (Mr) of 165×103, were heavily oxidized. Of the proteins known to distinguish the glue from non-adhesive mucus, only specific size variants were oxidized. The oxidation appears to occur within the first few seconds of secretion. Although carbonyls were detected by 2,4-dinitrophenylhydrazine (DNPH) in denatured proteins, they were not easily detected in the native state. The presence of reversible cross-links derived from carbonyls was tested for by treatment with sodium borohydride, which would reduce uncross-linked carbonyls to alcohols, but stabilize imine bonds formed by carbonyls and thus lead to less soluble complexes. Consistent with imine bond formation, sodium borohydride led to a 20–35% decrease in the amount of soluble protein with a Mr of 40–165 (×103) without changing the carbonyl content per protein. In contrast, the nucleophile hydroxylamine, which would competitively disrupt imine bonds, increased protein solubility in the glue. Finally, the primary amine groups on a protein with a Mr of 15×103 were not accessible to acid anhydrides. The results suggest that cross-links between aldehydes and primary amines contribute to the cohesive strength of the glue. PMID:21525316

Block Slides on Extremely Weak Tectonic Clay Seams in Openly Folded Tertiary Mud-Rocks at Auckland and the Rangitikei Valley, North Island, New Zealand

NASA Astrophysics Data System (ADS)

Prebble, Warwick M.; Williams, Ann L.

2016-06-01

Block slides have developed on extremely weak, thin clay seams of tectonic origin, parallel to bedding in gently dipping sandstones and mudstones of Tertiary age. Two areas of noted instability are investigated at Auckland and the Rangitikei valley. Dimensions range from 100 m across × 100 m long for short displacement block slides up to 4 km across × 3 km long for large landslide complexes in which block slides are a major component. Displacements of blocks range from incipient (cm) through short (30 m) to 2 or 3 km for large slides. Many of the Auckland slides are dormant but likely to move in a 2000 year return period earthquake or 100 year high intensity rain storm. At Rangitikei there are many active, younger slides. Sliding rates for active failures vary from a few cm/year to 50 m in 30 min. Host rocks are weak to very weak clayey sandstones and sandy mudstones. The seams are rich in smectite. They have polished and crushed walls, may have slickensides and some contain rounded rock fragments. Laboratory shear strength of the seams is 13 kPa cohesion and 13° friction, with a lower bound of 8° at zero cohesion. Strength is increased at the field scale by waviness, steps and splays. Continuity can be demonstrated over distances of hundreds of metres. Key investigation methods were mapping, shafts and trenches. Tectonic uplift, folding and faulting of the weak Tertiary strata and river down-cutting are perpetuating block slide development.

Push-out bond strengths of fiber-reinforced composite posts with various resin cements according to the root level

PubMed Central

Chang, Hoon-Sang; Noh, Young-Sin; Lee, Yoon; Min, Kyung-San

2013-01-01

PURPOSE The aim of this study was to determine whether the push-out bond strengths between the radicular dentin and fiber reinforced-composite (FRC) posts with various resin cements decreased or not, according to the coronal, middle or apical level of the root. MATERIALS AND METHODS FRC posts were cemented with one of five resin cement groups (RelyX Unicem: Uni, Contax with activator & LuxaCore-Dual: LuA, Contax & LuxaCore-Dual: Lu, Panavia F 2.0: PA, Super-Bond C&B: SB) into extracted human mandibular premolars. The roots were sliced into discs at the coronal, middle and apical levels. Push-out bond strength tests were performed with a universal testing machine at a crosshead speed of 0.5 mm/min, and the failure aspect was analyzed. RESULTS There were no significant differences (P>.05) in the bond strengths of the different resin cements at the coronal level, but there were significant differences in the bond strengths at the middle and apical levels (P<.05). Only the Uni and LuA cements did not show any significant decrease in their bond strengths at all the root levels (P>.05); all other groups had a significant decrease in bond strength at the middle or apical level (P<.05). The failure aspect was dominantly cohesive at the coronal level of all resin cements (P<.05), whereas it was dominantly adhesive at the apical level. CONCLUSION All resin cement groups showed decreases in bond strengths at the middle or apical level except LuA and Uni. PMID:24049569

Synthesis of an Al-Mn-Based Alloy Containing In Situ-Formed Quasicrystals and Evaluation of Its Mechanical and Corrosion Properties

NASA Astrophysics Data System (ADS)

Naglič, Iztok; Samardžija, Zoran; Delijić, Kemal; Kobe, Spomenka; Leskovar, Blaž; Markoli, Boštjan

2018-05-01

An Al-Mn alloy with additions of copper, magnesium, and silicon was prepared and cast into a copper mold. It contains in situ-formed icosahedral quasicrystals (iQCs), as confirmed by electron backscatter diffraction. The aim of this work is to present the mechanical and corrosion properties of this alloy and compare its properties with some conventional commercial materials. The compressive strength and compressive yield strength were 751 MPa and 377 MPa, while the compressive fracture strain was 19%. It was observed that intensive shearing caused the final fracture of the specimens and the fractured iQC dendrites still showed cohesion with the α-Al matrix. The polarization resistance and corrosion rate of the artificially aged alloy were 7.30 kΩ and 1.2 μm/year. The evaluated properties are comparable to conventional, discontinuously reinforced aluminum metal-matrix composites and structural wrought aluminum alloys.

Shear Bond Strengths between Three Different Yttria-Stabilized Zirconia Dental Materials and Veneering Ceramic and Their Susceptibility to Autoclave Induced Low-Temperature Degradation.

PubMed

Sehgal, Manoti; Bhargava, Akshay; Gupta, Sharad; Gupta, Prateek

2016-01-01

A study was undertaken to evaluate the effect of artificial aging through steam and thermal treatment as influencing the shear bond strength between three different commercially available zirconia core materials, namely, Upcera, Ziecon, and Cercon, layered with VITA VM9 veneering ceramic using Universal Testing Machine. The mode of failure between zirconia and ceramic was further analyzed as adhesive, cohesive, or mixed using stereomicroscope. X-ray diffraction and SEM (scanning electron microscope) analysis were done to estimate the phase transformation (m-phase fraction) and surface grain size of zirconia particles, respectively. The purpose of this study was to simulate the clinical environment by artificial aging through steam and thermal treatment so as the clinical function and nature of the bond between zirconia and veneering material as in a clinical trial of 15 years could be evaluated.

Static penetration resistance of soils

NASA Technical Reports Server (NTRS)

Durgunoglu, H. T.; Mitchell, J. K.

1973-01-01

Model test results were used to define the failure mechanism associated with the static penetration resistance of cohesionless and low-cohesion soils. Knowledge of this mechanism has permitted the development of a new analytical method for calculating the ultimate penetration resistance which explicitly accounts for penetrometer base apex angle and roughness, soil friction angle, and the ratio of penetration depth to base width. Curves relating the bearing capacity factors to the soil friction angle are presented for failure in general shear. Strength parameters and penetrometer interaction properties of a fine sand were determined and used as the basis for prediction of the penetration resistance encountered by wedge, cone, and flat-ended penetrometers of different surface roughness using the proposed analytical method. Because of the close agreement between predicted values and values measured in laboratory tests, it appears possible to deduce in-situ soil strength parameters and their variation with depth from the results of static penetration tests.

Constraints on the Density and Internal Strength of 1I/’Oumuamua

NASA Astrophysics Data System (ADS)

McNeill, Andrew; Trilling, David E.; Mommert, Michael

2018-04-01

1I/’Oumuamua was discovered by the Panoramic Survey Telescope and Rapid Response System (Pan-STARRS 1) on 2017 October 19. Unlike all previously discovered minor planets, this object was determined to have eccentricity e > 1.0, suggesting an interstellar origin. Since this discovery and within the limited window of opportunity, several photometric and spectroscopic studies of the object have been made. Using the measured light curve amplitudes and rotation periods we find that, under the assumption of a triaxial ellipsoid, a density range 1500 < ρ < 2800 kg m‑3 matches the observations and no significant cohesive strength is required. We also determine that an aspect ratio of 6 ± 1:1 is most likely after accounting for phase-angle effects and considering the potential effect of surface properties. This elongation is still remarkable, but less than some other estimates.

Click chemistry improved wet adhesion strength of mussel-inspired citrate-based antimicrobial bioadhesives

PubMed Central

Guo, Jinshan; Kim, Gloria B.; Shan, Dingying; Kim, Jimin P.; Hu, Jianqing; Wang, Wei; Hamad, Fawzi G.; Qian, Guoying; Rizk, Elias B.; Yang, Jian

2016-01-01

For the first time, a convenient copper-catalyzed azide-alkyne cycloaddition (CuAAC, click chemistry) was successfully introduced into injectable citrate-based mussel-inspired bioadhesives (iCMBAs, iCs) to improve both cohesive and wet adhesive strengths and elongate the degradation time, providing numerous advantages in surgical applications. The major challenge to developing such an adhesive was the mutual inhibition effect between the oxidant used for crosslinking catechol groups and the Cu(II) reductant used for CuAAC, which was successfully minimized by adding a biocompatible buffering agent typically used in cell culture, 4-(2-hydroxyethyl) -1-piperazineethanesulfonic acid (HEPES), as a copper chelating agent. Among the investigated formulations, the highest adhesion strength achieved (223.11 ± 15.94 kPa) was around 13 times higher than that of a commercially available fibrin glue (15.4 ± 2.8 kPa). In addition, dual-crosslinked (i.e. click crosslinking and mussel-inspired crosslinking) iCMBAs still preserved considerable antibacterial and antifungal capabilities that are beneficial for the bioadhesives used as hemostatic adhesives or sealants for wound management. PMID:27770631

Comparison between layering NbSe2 and rod characteristic of MgB2 by investigation of elastic constants

NASA Astrophysics Data System (ADS)

Shokri, Asiye; Yazdani, Ahmad; Barakati, Behrad

2018-03-01

The delicate balancing of strong anisotropy on strength of hybridisation resulted to CDW- order “TCDW=33K” and finally emerging superconductivity at “Tc = 7.2K” are the most intriguing question in characteristic behaviour of NbSe2. On other hand, the original mechanism of MgB2 old superconductor, which has unlike the cuprates a lower anisotropy on strength hybridisation is still unknown. We believe this could result to bond exchange and larger coherence length of the grain boundary to current. Since the cause and the mechanism of band strengths of two original layering and rod structures are consequence of bond- rupturing-atomic displacement, here the stability of crystalline structure of inter atomic potential through the elasticity-compressibility is investigated. Consequently, in order to clear out the strong difference between the layering NbSe2 and domination of rod-character of MgB2 the stability of both crystal structures through the cohesive energy c/a, czz and c33 are investigated. The proposed investigations are more evident on different characteristic behaviour of calculated parameters.

Spirit Leaves Telling Tracks

NASA Technical Reports Server (NTRS)

2004-01-01

Scientists have found clues about the nature of martian soil through analyzing wheel marks from the Mars Exploration Rover Spirit in this image. The image was taken by Spirit's rear hazard-identification camera just after the rover drove approximately 1 meter (3 feet) northwest off the Columbia Memorial Station (lander platform) early Thursday morning. That the wheel tracks are shallow indicates the soil has plenty of strength to support the moving rover. The well-defined track characteristics suggest the presence of very fine particles in the martian soil (along with larger particles). Scientists also think the soil may have some cohesive properties.

A phenomenological model of coating/substrate adhesion and interfacial bimetallic peeling stress in composite mirrors

NASA Technical Reports Server (NTRS)

Mcelroy, Paul M.; Lawson, Daniel D.

1990-01-01

Adhesion and interfacial stress between metal films and structural composite material substrates is discussed. A theoretical and conceptual basis for selecting coating materials for composite mirror substrates is described. A phenomenological model that interrelates cohesive tensile strength of thin film coatings and interfacial peeling stresses is presented. The model serves as a basis in determining gradiated materials response and compatibility of composite substrate and coating combinations. Parametric evaluation of material properties and geometrical factors such as coating thickness are used to determine the threshold stress levels for maintaining adhesion at the different interfaces.

A new Approach for Quantifying Root-Reinforcement of Streambanks: the RipRoot Model

NASA Astrophysics Data System (ADS)

Pollen, N. L.; Simon, A.

2003-12-01

Riparian vegetation plays an important role in controlling geotechnical and fluvial processes acting along and within streambanks through the binding effects of roots. Quantification of this mechanical effect is therefore essential to accurately model streambank stability. Until now, most attempts to include the effects of root reinforcement by riparian vegetation have used root-cohesion values estimated using the Wu et al. (1979) equation, requiring the tensile strengths and diameters of the roots crossing the potential shear-plane. However, the Wu et al. equation is a static model that assumes that all roots break, and that they all break simultaneously. Field observations and laboratory experiments have shown that in reality the roots do not all break simultaneously, and that the breaking of roots during mass failure is in fact a dynamic process. Static models such as the Wu et al. equation are therefore likely to produce overestimations of cohesion due to roots. As a response to this concern, a dynamic root reinforcement model (RipRoot) was developed, based on the concepts of fiber bundle models (FBM's) used in materials science. Within the model the root-soil system is loaded incrementally resulting in progressive root breaking and redistribution of stresses from the broken roots to the remaining intact roots in the soil matrix. The redistribution and loading process continues until either all of the roots have broken, or equilibrium is reached where the root network supports the driving force imposed on the bank. The increase in bank cohesion using the static Wu et al. equation are 18% to 38% higher than RipRoot for riparian tree species, including Black Willow, Sandbar Willow, Cottonwood, River Birch and Eastern Sycamore, and 49% higher for Switch Grass. These variations in cohesion values can have a significant impact on streambank Factor of Safety (Fs) values calculated using the Simon et al. (2000) bank-stability model. For example, a 3m high silt streambank had a Fs of 0.98 without vegetation, indicating instability. With the addition of cohesion from 200 River Birch roots this value increased to 1.22 using the RipRoot value (Conditionally Stable) and 1.37 using the Wu et al. equation (Stable). In this example both of the root models produced cohesion values that were large enough to make the bank more stable, but the more conservative value from RipRoot suggests the bank may only be conditionally stable. Results to date indicate that the dynamic nature of RipRoot removes some of the overestimation from the static equation of Wu et al. (1979), therefore producing more realistic values for root reinforcement, which are particularly useful and important in the context of river management and restoration.

A square-force cohesion model and its extraction from bulk measurements

NASA Astrophysics Data System (ADS)

Liu, Peiyuan; Lamarche, Casey; Kellogg, Kevin; Hrenya, Christine

2017-11-01

Cohesive particles remain poorly understood, with order of magnitude differences exhibited for prior, physical predictions of agglomerate size. A major obstacle lies in the absence of robust models of particle-particle cohesion, thereby precluding accurate prediction of the behavior of cohesive particles. Rigorous cohesion models commonly contain parameters related to surface roughness, to which cohesion shows extreme sensitivity. However, both roughness measurement and its distillation into these model parameters are challenging. Accordingly, we propose a ``square-force'' model, where cohesive force remains constant until a cut-off separation. Via DEM simulations, we demonstrate validity of the square-force model as surrogate of more rigorous models, when its two parameters are selected to match the two key quantities governing dense and dilute granular flows, namely maximum cohesive force and critical cohesive energy, respectively. Perhaps more importantly, we establish a method to extract the parameters in the square-force model via defluidization, due to its ability to isolate the effects of the two parameters. Thus, instead of relying on complicated scans of individual grains, determination of particle-particle cohesion from simple bulk measurements becomes feasible. Dow Corning Corporation.

Measuring team cohesion: observations from the science.

PubMed

Salas, Eduardo; Grossman, Rebecca; Hughes, Ashley M; Coultas, Chris W

2015-05-01

The aim of this study was to review literature relevant to cohesion measurement, explore developing measurement approaches, and provide theoretical and practical recommendations for optimizing cohesion measurement. Cohesion is essential for team effectiveness and performance, leading researchers to focus attention on understanding how to enhance it. However, cohesion is inconsistently defined and measured, making it difficult to compare findings across studies and limiting the ability to advance science and practice. We reviewed empirical research through which we uncovered specific information about cohesion's conceptualization, measurement, and relationships with performance, culminating in a set of current trends from which we provide suggestions and possible solutions to guide future efforts and help the field converge toward greater consistency. Cohesion demonstrates more significant relationships with performance when conceptualized using social and task (but not other) dimensions and when analyses are performed at the team level. Cohesion is inherently temporal, yet researchers rarely measure cohesion at multiple points during the life of a team. Finally, cohesion matters in large, dynamic collectives, complicating measurement. However, innovative and unobtrusive methodologies are being used, which we highlight. Practitioners and researchers are encouraged to define cohesion with task and social subdimensions and to measure with behavioral and attitudinal operationalizations. Individual and team-oriented items are recommended, though team-level analyses are most effective. Innovative/unobtrusive methods should be further researched to enable cohesion measurement longitudinally and in large, dynamic collectives. By applying our findings and conclusions, researchers and practitioners will be more likely to find consistent, reliable, and significant cohesion-to-performance relationships. This work is not subject to U.S. copyright restrictions.

Effect of additional etching and ethanol-wet bonding on the dentin bond strength of one-step self-etch adhesives

PubMed Central

Ahn, Joonghee; Jung, Kyoung-Hwa; Son, Sung-Ae; Hur, Bock; Kwon, Yong-Hoon

2015-01-01

Objectives This study examined the effects of additional acid etching on the dentin bond strength of one-step self-etch adhesives with different compositions and pH. The effect of ethanol wetting on etched dentin bond strength of self-etch adhesives was also evaluated. Materials and Methods Forty-two human permanent molars were classified into 21 groups according to the adhesive types (Clearfil SE Bond [SE, control]; G-aenial Bond [GB]; Xeno V [XV]; Beauti Bond [BB]; Adper Easy Bond [AE]; Single Bond Universal [SU]; All Bond Universal [AU]), and the dentin conditioning methods. Composite resins were placed on the dentin surfaces, and the teeth were sectioned. The microtensile bond strength was measured, and the failure mode of the fractured specimens was examined. The data were analyzed statistically using two-way ANOVA and Duncan's post hoc test. Results In GB, XV and SE (pH ≤ 2), the bond strength was decreased significantly when the dentin was etched (p < 0.05). In BB, AE and SU (pH 2.4 - 2.7), additional etching did not affect the bond strength (p > 0.05). In AU (pH = 3.2), additional etching increased the bond strength significantly (p < 0.05). When adhesives were applied to the acid etched dentin with ethanol-wet bonding, the bond strength was significantly higher than that of the no ethanol-wet bonding groups, and the incidence of cohesive failure was increased. Conclusions The effect of additional acid etching on the dentin bond strength was influenced by the pH of one-step self-etch adhesives. Ethanol wetting on etched dentin could create a stronger bonding performance of one-step self-etch adhesives for acid etched dentin. PMID:25671215

An examination of the relationship between athlete leadership and cohesion using social network analysis.

PubMed

Loughead, Todd M; Fransen, Katrien; Van Puyenbroeck, Stef; Hoffmann, Matt D; De Cuyper, Bert; Vanbeselaere, Norbert; Boen, Filip

2016-11-01

Two studies investigated the structure of different athlete leadership networks and its relationship to cohesion using social network analysis. In Study 1, we examined the relationship between a general leadership quality network and task and social cohesion as measured by the Group Environment Questionnaire (GEQ). In Study 2, we investigated the leadership networks for four different athlete leadership roles (task, motivational, social and external) and their association with task and social cohesion networks. In Study 1, the results demonstrated that the general leadership quality network was positively related to task and social cohesion. The results from Study 2 indicated positive correlations between the four leadership networks and task and social cohesion networks. Further, the motivational leadership network emerged as the strongest predictor of the task cohesion network, while the social leadership network was the strongest predictor of the social cohesion network. The results complement a growing body of research indicating that athlete leadership has a positive association with cohesion.

Evaluation of shear bond strength of porcelain bonded to laser welded titanium surface and determination of mode of bond failure.

PubMed

Patil, Narendra P; Dandekar, Minal; Nadiger, Ramesh K; Guttal, Satyabodh S

2010-09-01

The aim of this study was to evaluate the shear bond strength of porcelain to laser welded titanium surface and to determine the mode of bond failure through scanning electron microscopy (SEM) and energy dispersive spectrophotometry (EDS). Forty five cast rectangular titanium specimens with the dimension of 10 mm x 8 mm x 1 mm were tested. Thirty specimens had a perforation of 2 mm diameter in the centre. These were randomly divided into Group A and B. The perforations in the Group B specimens were repaired by laser welding using Cp Grade II titanium wire. The remaining 15 specimens were taken as control group. All the test specimens were layered with low fusing porcelain and tested for shear bond strength. The debonded specimens were subjected to SEM and EDS. Data were analysed with 1-way analysis of variance and Student's t-test for comparison among the different groups. One-way analysis of variance (ANOVA) showed no statistically significant difference in shear bond strength values at a 5% level of confidence. The mean shear bond strength values for control group, Group A and B was 8.4 +/- 0.5 Mpa, 8.1 +/- 0.4 Mpa and 8.3 +/- 0.3 Mpa respectively. SEM/EDS analysis of the specimens showed mixed and cohesive type of bond failure. Within the limitations of the study laser welding did not have any effect on the shear bond strength of porcelain bonded to titanium.

Relationship between surface area for adhesion and tensile bond strength--evaluation of a micro-tensile bond test.

PubMed

Sano, H; Shono, T; Sonoda, H; Takatsu, T; Ciucchi, B; Carvalho, R; Pashley, D H

1994-07-01

The purpose of this study was to test the null hypothesis that there is no relationship between the bonded surface area of dentin and the tensile strength of adhesive materials. The enamel was removed from the occlusal surface of extracted human third molars, and the entire flat surface was covered with resin composite bonded to the dentin to form a flat resin composite crown. Twenty-four hours later, the bonded specimens were sectioned parallel to the long axis of the tooth into 10-20 thin sections whose upper part was composed of resin composite with the lower half being dentin. These small sections were trimmed using a high speed diamond bur into an hourglass shape with the narrowest portion at the bonded interface. Surface area was varied by altering the specimen thickness and width. Tensile bond strength was measured using custom-made grips in a universal testing machine. Tensile bond strength was inversely related to bonded surface area. At surface areas below 0.4 mm2, the tensile bond strengths were about 55 MPa for Clearfil Liner Bond 2 (Kuraray Co., Ltd.), 38 MPa for Scotchbond MP (3M Dental Products), and 20 MPa for Vitremer (3M Dental Products). At these small surface areas all of the bond failures were adhesive in nature. This new method permits measurement of high bond strengths without cohesive failure of dentin. It also permits multiple measurements to be made within a single tooth.

Comparison of shear bond strengths of conventional orthodontic composite and nano-ceramic restorative composite: an in vitro study.

PubMed

Nagar, Namit; Vaz, Anna C

2013-01-01

To compare the shear bond strength of a nano-ceramic restorative composite Ceram-X Mono(TM♦), a restorative resin with the traditional orthodontic composite Transbond XT(TM†) and to evaluate the site of bond failure using Adhesive Remnant Index. Sixty extracted human premolars were divided into two groups of 30 each. Stainless steel brackets were bonded using Transbond XT(TM†) (Group I) and Ceram-X Mono(TM♦) (Group II) according to manufacturer's protocol. Shear bond strength was measured on Universal testing machine at crosshead speed of 1 mm/minute. Adhesive Remnant Index scores were assigned to debonded brackets of each group. Data was analyzed using unpaired 't' test and Chi square test. The mean shear bond strength of Group I (Transbond XT(TM†)) was 12.89 MPa ± 2.19 and that of Group II (Ceram-X Mono(TM)) was 7.29 MPa ± 1.76. Unpaired 't' test revealed statistically significant differences amongst the shear bond strength of the samples measured. Chi-square test revealed statistically insignificant differences amongst the ARI scores of the samples measured. Ceram-X Mono(TM♦) had a lesser mean shear bond strength when compared to Transbond XT(TM†) which was statistically significant difference. However, the mean shear bond of Ceram X Mono was within the clinically acceptable range for bonding. Ceram-X Mono(TM†) and Transbond XT(TM†) showed cohesive fracture of adhesive in 72.6% and 66.6% of the specimens, respectively.

Microtensile bond strength of enamel after bleaching.

PubMed

Lago, Andrea Dias Neves; Garone-Netto, Narciso

2013-01-01

To evaluate the bond strength of a composite resin to the bovine enamel bleached with 35% hydrogen peroxide. It was used an etching-and-rinse adhesive system employed immediately, 7 and 14 days after the bleaching. Twenty bovine teeth were randomly distributed into 4 groups (n = 5), 3 experimental and 1 control. G1: Unbleached + restoration 14 days after storage in artificial saliva (control); G2: Bleached + restoration immediately after bleaching; G3: Bleached + restoration 7 days after bleaching; G4: Bleached + restoration 14 days after bleaching. Their buccal enamel surfaces were flattened, and a 25 mm² (5 × 5 mm) area from each one of these regions was outlined so as to standardize the experimental region. Universal hybrid composite resin Filtek™Z350 was inserted into four layers of 1 mm each and photo-activated. The bond strength was quantitatively evaluated by a microtensile test (1.0 mm/min) 24 h after the restorative procedures. The failure mode was assessed through scanning electron microscopy (SEM). There was a significant reduction in the bond strength of the restored teeth immediately after the bleaching (G2). There were no significant differences in enamel bond strength between groups G1, G3, and G4. There was a predominance of adhesive and mixed (cohesive + adhesive) failure in all groups. The 7-day-period after the end of the bleaching with 35% hydrogen peroxide was enough to achieve the appropriate values of bond strength to the enamel.

Effects of silicon coating on bond strength of two different titanium ceramic to titanium.

PubMed

Ozcan, Isil; Uysal, Hakan

2005-08-01

This study investigated the effect of silicon coating (SiO2) by magnetron sputtering on bond strength of two different titanium ceramics to titanium. Sixty cast titanium specimens were prepared following the protocol ISO 9693. Titanium specimens were divided into two test and control groups with 15 specimens in each. Test groups were silicon coated by the magnetron sputtering technique. Two titanium ceramics (Triceram and Duceratin) were applied on both test (coated) and control (uncoated) metal specimens. The titanium-ceramic specimens were subjected to a three point flexural test. The groups were compared for their bond strength. SEM and SEM/EDS analyses were performed on the delaminated titanium surfaces to ascertain bond failure. The mean bond strength of Ti-Duceratin, Ti-Triceram, Si-coated Ti-Duceratin and Si-coated Ti-Triceram were 17.22+/-2.43, 23.31+/-3.18, 23.21+/-3.81 and 24.91+/-3.70 MPa, respectively. While the improvement in bond strength was 30% for Duceratin, it was statistically insignificant for Triceram. An adhesive mode of failure was observed in the Duceratin control group. In the silicoated Duceratin specimen, the bonded ceramic boundaries were wider but less than in the silicoated Triceram specimen. In the coated Triceram specimen, the ceramic retained areas were frequent and the failure mode was generally cohesive. Silicon coating was significantly effective in both preventing titanium oxide layer formation and in improving bond strength for Duceratin. However, it was of less value for Triceram.

Evaluating the bonding of two adhesive systems to enamel submitted to whitening dentifrices.

PubMed

Briso, André Luiz Fraga; Toseto, Roberta Mariano; de Arruda, Alex Mendes; Tolentino, Patricia Ramos; de Alexandre, Rodrigo Sversut; dos Santos, Paulo Henrique

2010-01-01

The aim of this study was to evaluate by micro-shear bond strength test, the bond strength of composite resin restoration to enamel submitted to whitening dentifrices. Forty bovine teeth were embedded in polystyrene resin and polished. The specimens were randomly divided into eight groups (n=5), according to the dentifrice (carbamide peroxide, hydrogen peroxide and conventional dentifrice) and the adhesive system (Prime & Bond 2.1 and Adper Single Bond 2). Dentifrice was applied for 15 minutes a day, for 21 days. Thirty minutes after the last exposure to dentifrice, the samples were submitted to a bonding procedure with the respective adhesive system. After that, four buttons of resin were bonded in each sample using transparent cylindrical molds. After 24 hours, the teeth were submitted to the micro-shear bond strength test and subsequent analysis of the fracture mode. Data were submitted to analysis of variance and Fisher's PLSD test (alpha = 0.05). The micro-shear bond strength showed no difference between adhesives systems but a significant reduction was found between the control and carbamide groups (p = 0.0145) and the control and hydrogen groups (p = 0.0370). The evaluation of the failures modes showed that adhesive failures were predominant. Cohesive failures were predominant in group IV The use of dentifrice with peroxides can decrease bonding strength in enamel.

Comparison of the bond strength of stainless steel orthodontic brackets bonded to crown porcelains.

PubMed

Chay, Siew Han; Wattanapayungkul, Pranee; Yap, Adrian U Jin; Loh, Poey Ling; Chung, Sew Meng

2005-05-01

The bond strengths and mode of failure of stainless steel orthodontic brackets bonded to the newer all-ceramic crown systems has not been fully investigated. To compare the shear-peel bond strengths and modes of failure of stainless steel Begg orthodontic brackets bonded to all-ceramic crown systems (Finesse, Empress II) and a conventional feldsphatic crown porcelain (Vita Omega 900). Fifteen flat-surface discs of three crown porcelains (Finesse, Vita Omega 900, Empress II) were made and mounted in acrylic moulds. The discs were pumiced, etched with phosphoric acid, primed with silane, and a flat stainless steel Begg bracket bonded to each disc with a chemical cure composite resin (Unite Bond). The discs were stored for one week in water and debonded with a sheer-peel load in an Instron uniaxial testing system with a crosshead speed of 0.5 mm/min. The composite remnants on the ceramic surfaces were classified using the Adhesive Remnant Index (ARI). The bond strength of Finesse (15.03 +/- 1.90 MPa) was significantly greater (p < 0.001) than Vita Omega 900 11.51 +/- 2.35 MPa) and Empress II (11.12 +/- 1.78 MPa). There were no significant differences among the ARI scores. The mode of failure was a mixture of adhesive and cohesive failure. The results indicate that the bond strengths of stainless steel orthodontic brackets bonded to Finesse and Empress II porcelains are clinically acceptable.

Effects of text cohesion on comprehension and retention of colorectal cancer screening information: a preliminary study.

PubMed

Liu, Chiung-Ju; Rawl, Susan M

2012-01-01

Increasing readability of written cancer prevention information is a fundamental step to increasing awareness and knowledge of cancer screening. Instead of readability formulas, the present study focused on text cohesion, which is the degree to which the text content ties together. The purpose of this study was to examine the effect of text cohesion on reading times, comprehension, and retention of colorectal cancer prevention information. English-speaking adults (50 years of age or older) were recruited from local communities. Participants were randomly assigned to read colorectal cancer prevention subtopics presented at 2 levels of text cohesion: from higher cohesion to lower cohesion, or vice versa. Reading times, word recognition, text comprehension, and recall were assessed after reading. Two weeks later, text comprehension and recall were reassessed. Forty-two adults completed the study, but five were lost to follow up. Higher text cohesion showed a significant effect on reading times and text comprehension but not on word recognition and recall. The effect of text cohesion was not found on text comprehension and recall after 2 weeks. Increasing text cohesion facilitates reading speed and comprehension of colorectal cancer prevention information. Further research on the effect of text cohesion is warranted.

Social cohesion matters in health.

PubMed

Chuang, Ying-Chih; Chuang, Kun-Yang; Yang, Tzu-Hsuan

2013-10-28

The concept of social cohesion has invoked debate due to the vagueness of its definition and the limitations of current measurements. This paper attempts to examine the concept of social cohesion, develop measurements, and investigate the relationship between social cohesion and individual health. This study used a multilevel study design. The individual-level samples from 29 high-income countries were obtained from the 2000 World Value Survey (WVS) and the 2002 European Value Survey. National-level social cohesion statistics were obtained from Organization of Economic Cooperation and Development datasets, World Development Indicators, and Asian Development Bank key indicators for the year 2000, and from aggregating responses from the WVS. In total 47,923 individuals were included in this study. The factor analysis was applied to identify dimensions of social cohesion, which were used as entities in the cluster analysis to generate a regime typology of social cohesion. Then, multilevel regression models were applied to assess the influences of social cohesion on an individual's self-rated health. Factor analysis identified five dimensions of social cohesion: social equality, social inclusion, social development, social capital, and social diversity. Then, the cluster analysis revealed five regimes of social cohesion. A multi-level analysis showed that respondents in countries with higher social inclusion, social capital, and social diversity were more likely to report good health above and beyond individual-level characteristics. This study is an innovative effort to incorporate different aspects of social cohesion. This study suggests that social cohesion was associated with individual self-rated after controlling individual characteristics. To achieve further advancement in population health, developed countries should consider policies that would foster a society with a high level of social inclusion, social capital, and social diversity. Future research could focus on identifying possible pathways by which social cohesion influences various health outcomes.

Indentation of a free-falling lance penetrometer into a poroelastic seabed

NASA Astrophysics Data System (ADS)

Elsworth, Derek; Lee, Dae Sung

2005-02-01

A solution is developed for the build-up, steady and post-arrest dissipative pore fluid pressure fields that develop around a blunt penetrometer that self-embeds from freefall into the seabed. Arrest from freefall considers deceleration under undrained conditions in a purely cohesive soil, with constant shear strength with depth. The resulting decelerating velocity field is controlled by soil strength, geometric bearing capacity factors, and inertial components. At low impact velocities the embedment process is controlled by soil strength, and at high velocities by inertia. With the deceleration defined, a solution is evaluated for a point normal dislocation penetrating in a poroelastic medium with a prescribed decelerating velocity. Dynamic steady pressures, PD, develop relative to the penetrating tip geometry with their distribution conditioned by the non-dimensional penetration rate, UD, incorporating impacting penetration rate, consolidation coefficient and penetrometer radius, and the non-dimensional strength, ND, additionally incorporating undrained shear strength of the sediment. Pore pressures develop to a steady peak magnitude at the penetrometer tip, and drop as PD=1/xD with distance xD behind the tip and along the shaft. Peak induced pressure magnitudes may be correlated with sediment permeabilities, post-arrest dissipation rates may be correlated with consolidation coefficients, and depths of penetration may be correlated with shear strengths. Together, these records enable strength and transport parameters to be recovered from lance penetrometer data. Penetrometer data recorded off La Palma in the Canary Islands (J. Volcanol. Geotherm. Res. 2000; 101:253) are used to recover permeabilities and consolidation coefficients from peak pressure and dissipation response, respectively. Copyright

Dentin pretreatment and adhesive temperature as affecting factors on bond strength of a universal adhesive system.

PubMed

Sutil, Bruna Gabrielle da Silva; Susin, Alexandre Henrique

2017-01-01

To evaluate the effects of dentin pretreatment and temperature on the bond strength of a universal adhesive system to dentin. Ninety-six extracted non-carious human third molars were randomly divided into 12 groups (n=8) according to Scotchbond Universal Adhesive (SbU) applied in self-etch (SE) and etch-and-rinse (ER) mode, adhesive temperature (20°C or 37°C) and sodium bicarbonate or aluminum oxide air abrasion. After composite build up, bonded sticks with cross-sectional area of 1 mm2 were obtained to evaluate the microtensile bond strength (μTBS). The specimens were tested at a crosshead speed of 0.5 mm/min on a testing machine until failure. Fractured specimens were analyzed under stereomicroscope to determine the failure patterns in adhesive, cohesive (dentin or resin) and mixed fractures. The microtensile bond strength data was analyzed using two-way ANOVA and Tukey's test (α=5%). Interaction between treatment and temperature was statistically significant for SbU applied in self-etch technique. Both dentin treatments showed higher bond strength for ER mode, regardless of adhesive temperature. When compared to control group, sodium bicarbonate increased bond strength of SbU in SE technique. Adhesive temperature did not significantly affect the μTBS of tested groups. Predominantly, adhesive failure was observed for all groups. Dentin surface treatment with sodium bicarbonate air abrasion improves bond strength of SbU, irrespective of adhesive application mode, which makes this approach an alternative to increase adhesive performance of Scotchbond Universal Adhesive to dentin.

Dentin pretreatment and adhesive temperature as affecting factors on bond strength of a universal adhesive system

PubMed Central

Sutil, Bruna Gabrielle da Silva; Susin, Alexandre Henrique

2017-01-01

Abstract Objectives: To evaluate the effects of dentin pretreatment and temperature on the bond strength of a universal adhesive system to dentin. Material and Methods: Ninety-six extracted non-carious human third molars were randomly divided into 12 groups (n=8) according to Scotchbond Universal Adhesive (SbU) applied in self-etch (SE) and etch-and-rinse (ER) mode, adhesive temperature (20°C or 37°C) and sodium bicarbonate or aluminum oxide air abrasion. After composite build up, bonded sticks with cross-sectional area of 1 mm2 were obtained to evaluate the microtensile bond strength (μTBS). The specimens were tested at a crosshead speed of 0.5 mm/min on a testing machine until failure. Fractured specimens were analyzed under stereomicroscope to determine the failure patterns in adhesive, cohesive (dentin or resin) and mixed fractures. The microtensile bond strength data was analyzed using two-way ANOVA and Tukey's test (α=5%). Results: Interaction between treatment and temperature was statistically significant for SbU applied in self-etch technique. Both dentin treatments showed higher bond strength for ER mode, regardless of adhesive temperature. When compared to control group, sodium bicarbonate increased bond strength of SbU in SE technique. Adhesive temperature did not significantly affect the μTBS of tested groups. Predominantly, adhesive failure was observed for all groups. Conclusions: Dentin surface treatment with sodium bicarbonate air abrasion improves bond strength of SbU, irrespective of adhesive application mode, which makes this approach an alternative to increase adhesive performance of Scotchbond Universal Adhesive to dentin. PMID:29069151

Influence of nano-structured alumina coating on shear bond strength between Y-TZP ceramic and various dual-cured resin cements.

PubMed

Lee, Jung-Jin; Choi, Jung-Yun; Seo, Jae-Min

2017-04-01

The purpose of this study was to evaluate the effect of nano-structured alumina surface coating on shear bond strength between Y-TZP ceramic and various dual-cured resin cements. A total of 90 disk-shaped zirconia specimens (HASS CO., Gangneung, Korea) were divided into three groups by surface treatment method: (1) airborne particle abrasion, (2) tribochemicalsilica coating, and (3) nano-structured alumina coating. Each group was categorized into three subgroups of ten specimens and bonded with three different types of dual-cured resin cements. After thermocycling, shear bond strength was measured and failure modes were observed through FE-SEM. Two-way ANOVA and the Tukey's HSD test were performed to determine the effects of surface treatment method and type of cement on bond strength ( P <.05). To confirm the correlation of surface treatment and failure mode, the Chi-square test was used. Groups treated with the nanostructured alumina coating showed significantly higher shear bond strength compared to other groups treated with airborne particle abrasion or tribochemical silica coating. Clearfil SA Luting showed a significantly higher shear bond strength compared to RelyX ARC and RelyX Unicem. The cohesive failure mode was observed to be dominant in the groups treated with nano-structured alumina coating, while the adhesive failure mode was prevalent in the groups treated with either airborne particle abrasion or tribochemical silica coating. Nano-structured alumina coating is an effective zirconia surface treatment method for enhancing the bond strength between Y-TZP ceramic and various dual-cured resin cements.

Pds5 regulators segregate cohesion and condensation pathways in Saccharomyces cerevisiae

PubMed Central

Tong, Kevin; Skibbens, Robert V.

2015-01-01

Cohesins are required both for the tethering together of sister chromatids (termed cohesion) and subsequent condensation into discrete structures—processes fundamental for faithful chromosome segregation into daughter cells. Differentiating between cohesin roles in cohesion and condensation would provide an important advance in studying chromatin metabolism. Pds5 is a cohesin-associated factor that is essential for both cohesion maintenance and condensation. Recent studies revealed that ELG1 deletion suppresses the temperature sensitivity of pds5 mutant cells. However, the mechanisms through which Elg1 may regulate cohesion and condensation remain unknown. Here, we report that ELG1 deletion from pds5-1 mutant cells results in a significant rescue of cohesion, but not condensation, defects. Based on evidence that Elg1 unloads the DNA replication clamp PCNA from DNA, we tested whether PCNA overexpression would similarly rescue pds5-1 mutant cell cohesion defects. The results indeed reveal that elevated levels of PCNA rescue pds5-1 temperature sensitivity and cohesion defects, but do not rescue pds5-1 mutant cell condensation defects. In contrast, RAD61 deletion rescues the condensation defect, but importantly, neither the temperature sensitivity nor cohesion defects exhibited by pds5-1 mutant cells. In combination, these findings reveal that cohesion and condensation are separable pathways and regulated in nonredundant mechanisms. These results are discussed in terms of a new model through which cohesion and condensation are spatially regulated. PMID:25986377

Pds5 regulators segregate cohesion and condensation pathways in Saccharomyces cerevisiae.

PubMed

Tong, Kevin; Skibbens, Robert V

2015-06-02

Cohesins are required both for the tethering together of sister chromatids (termed cohesion) and subsequent condensation into discrete structures-processes fundamental for faithful chromosome segregation into daughter cells. Differentiating between cohesin roles in cohesion and condensation would provide an important advance in studying chromatin metabolism. Pds5 is a cohesin-associated factor that is essential for both cohesion maintenance and condensation. Recent studies revealed that ELG1 deletion suppresses the temperature sensitivity of pds5 mutant cells. However, the mechanisms through which Elg1 may regulate cohesion and condensation remain unknown. Here, we report that ELG1 deletion from pds5-1 mutant cells results in a significant rescue of cohesion, but not condensation, defects. Based on evidence that Elg1 unloads the DNA replication clamp PCNA from DNA, we tested whether PCNA overexpression would similarly rescue pds5-1 mutant cell cohesion defects. The results indeed reveal that elevated levels of PCNA rescue pds5-1 temperature sensitivity and cohesion defects, but do not rescue pds5-1 mutant cell condensation defects. In contrast, RAD61 deletion rescues the condensation defect, but importantly, neither the temperature sensitivity nor cohesion defects exhibited by pds5-1 mutant cells. In combination, these findings reveal that cohesion and condensation are separable pathways and regulated in nonredundant mechanisms. These results are discussed in terms of a new model through which cohesion and condensation are spatially regulated.

A two-field modified Lagrangian formulation for robust simulations of extrinsic cohesive zone models

NASA Astrophysics Data System (ADS)

Cazes, F.; Coret, M.; Combescure, A.

2013-06-01

This paper presents the robust implementation of a cohesive zone model based on extrinsic cohesive laws (i.e. laws involving an infinite initial stiffness). To this end, a two-field Lagrangian weak formulation in which cohesive tractions are chosen as the field variables along the crack's path is presented. Unfortunately, this formulation cannot model the infinite compliance of the broken elements accurately, and no simple criterion can be defined to determine the loading-unloading change of state at the integration points of the cohesive elements. Therefore, a modified Lagrangian formulation using a fictitious cohesive traction instead of the classical cohesive traction as the field variable is proposed. Thanks to this change of variable, the cohesive law becomes an increasing function of the equivalent displacement jump, which eliminates the problems mentioned previously. The ability of the proposed formulations to simulate fracture accurately and without field oscillations is investigated through three numerical test examples.

Social cohesion and self-rated health: The moderating effect of neighborhood physical disorder.

PubMed

Bjornstrom, Eileen E S; Ralston, Margaret L; Kuhl, Danielle C

2013-12-01

Using data from the Los Angeles Family and Neighborhood Survey and its companion datasets, we examined how neighborhood disorder, perceived danger and both individually perceived and contextually measured neighborhood social cohesion are associated with self-rated health. Results indicate that neighborhood disorder is negatively associated with health and the relationship is explained by perceived cohesion and danger, which are both also significant predictors of health. Further, individually perceived cohesion emerges as a more important explanation of self-rated health than neighborhood-level social cohesion. Finally, neighborhood disorder and perceived cohesion interact to influence health, such that cohesion is especially beneficial when residents live in neighborhoods characterized by low to moderate disorder; once disorder is at high levels, cohesion no longer offers protection against poor health. We interpret our findings as they relate to prior research on neighborhoods, psychosocial processes, and health, and discuss their implications for intervention efforts that address disorder in urban communities.

Relating Cohesive Zone Model to Linear Elastic Fracture Mechanics

NASA Technical Reports Server (NTRS)

Wang, John T.

2010-01-01

The conditions required for a cohesive zone model (CZM) to predict a failure load of a cracked structure similar to that obtained by a linear elastic fracture mechanics (LEFM) analysis are investigated in this paper. This study clarifies why many different phenomenological cohesive laws can produce similar fracture predictions. Analytical results for five cohesive zone models are obtained, using five different cohesive laws that have the same cohesive work rate (CWR-area under the traction-separation curve) but different maximum tractions. The effect of the maximum traction on the predicted cohesive zone length and the remote applied load at fracture is presented. Similar to the small scale yielding condition for an LEFM analysis to be valid. the cohesive zone length also needs to be much smaller than the crack length. This is a necessary condition for a CZM to obtain a fracture prediction equivalent to an LEFM result.

Gradient boride layers formed by diffusion carburizing and laser boriding

NASA Astrophysics Data System (ADS)

Kulka, M.; Makuch, N.; Dziarski, P.; Mikołajczak, D.; Przestacki, D.

2015-04-01

Laser boriding, instead of diffusion boriding, was proposed to formation of gradient borocarburized layers. The microstructure and properties of these layers were compared to those-obtained after typical diffusion borocarburizing. First method of treatment consists in diffusion carburizing and laser boriding only. In microstructure three zones are present: laser borided zone, hardened carburized zone and carburized layer without heat treatment. However, the violent decrease in the microhardness was observed below the laser borided zone. Additionally, these layers were characterized by a changeable value of mass wear intensity factor thus by a changeable abrasive wear resistance. Although at the beginning of friction the very low values of mass wear intensity factor Imw were obtained, these values increased during the next stages of friction. It can be caused by the fluctuations in the microhardness of the hardened carburized zone (HAZ). The use of through hardening after carburizing and laser boriding eliminated these fluctuations. Two zones characterized the microstructure of this layer: laser borided zone and hardened carburized zone. Mass wear intensity factor obtained a constant value for this layer and was comparable to that-obtained in case of diffusion borocarburizing and through hardening. Therefore, the diffusion boriding could be replaced by the laser boriding, when the high abrasive wear resistance is required. However, the possibilities of application of laser boriding instead of diffusion process were limited. In case of elements, which needed high fatigue strength, the substitution of diffusion boriding by laser boriding was not advisable. The surface cracks formed during laser re-melting were the reason for relatively quickly first fatigue crack. The preheating of the laser treated surface before laser beam action would prevent the surface cracks and cause the improved fatigue strength. Although the cohesion of laser borided carburized layer was sufficient, the diffusion borocarburized layer showed a better cohesion.

Influence of fluoride varnish on shear bond strength of a universal adhesive on intact and demineralized enamel.

PubMed

Ortiz-Ruiz, Antonio José; Muñoz-Gómez, Iban Jesús; Pérez-Pardo, Ana; Germán-Cecilia, Concepción; Martínez-Beneyto, Yolanda; Vicente, Ascensión

2018-04-27

The aim was to evaluate the effect of fluoride varnish on the shear bond strength (SBS) on polished and non-polished intact and demineralized enamel. Bovine incisors (half demineralized) were used. Bifluorid 12™ was applied. Bonding was made with Futurabond ® M + and GrandioSO, 24 h and 7 days after varnishing. In some groups, varnish was removed by polishing before bonding. SBS was measured. Fracture type was determined by stereomicroscopy and scanning electron microscope (SEM) observations of the enamel surface were made. Between-group differences were determined by one-way ANOVA and the Tukey test. Associations between study factors and fracture modes were analysed using contingency tables and Pearson's chi-squared test. For intact enamel, SBS on varnished enamel at 24 h was significantly less than in the other groups. SBS recovered 7 days after varnishing. Varnish elimination after 24 h significantly increased the SBS. However, removal at 7 days did not modify SBS. SBS on demineralized enamel groups was significantly less than in intact enamel, except for demineralized enamel varnished and removed at 7 days. Demineralized enamel was associated with cohesive enamel fractures and intact enamel with cohesive fractures of the composite and adhesive fractures. SEM of varnish surfaces showed a homogenous layer scattered with amorphous precipitate. In conclusion, on intact enamel fluoride varnish had a negative effect on SBS at 24 h, which disappeared after 7 days. On demineralized enamel, varnish did not reduce SBS at either time. Polishing the varnished enamel surface showed a similar SBS to intact enamel after 7 days.

Micromechanical measurements of the effect of surfactants on cyclopentane hydrate shell properties.

PubMed

Brown, Erika P; Koh, Carolyn A

2016-01-07

Investigating the effect of surfactants on clathrate hydrate growth and morphology, especially particle shell strength and cohesion force, is critical to advancing new strategies to mitigate hydrate plug formation. In this study, dodecylbenzenesulfonic acid and polysorbate 80 surfactants were included during the growth of cyclopentane hydrates at several concentrations above and below the critical micelle concentration. A novel micromechanical method was applied to determine the force required to puncture the hydrate shell using a glass cantilever (with and without surfactants), with annealing times ranging from immediately after the hydrate nucleated to 90 minutes after formation. It was shown that the puncture force was decreased by the addition of both surfactants up to a maximum of 79%. Over the entire range of annealing times (0-90 minutes), the thickness of the hydrate shell was also measured. However, there was no clear change in shell thickness with the addition of surfactants. The growth rate of the hydrate shell was found to vary less than 15% with the addition of surfactants. The cohesive force between two hydrate particles was measured for each surfactant and found to be reduced by 28% to 78%. Interfacial tension measurements were also performed. Based on these results, microscopic changes to the hydrate shell morphology (due to the presence of surfactants) were proposed to cause the decrease in the force required to break the hydrate shell, since no macroscopic morphology changes were observed. Understanding the hydrate shell strength can be critical to reducing the capillary bridge interaction between hydrate particles or controlling the release of unconverted water from the interior of the hydrate particle, which can cause rapid hydrate conversion.

LARGE SUPER-FAST ROTATOR HUNTING USING THE INTERMEDIATE PALOMAR TRANSIENT FACTORY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, Chan-Kao; Lin, Hsing-Wen; Ip, Wing-Huen

In order to look for large super-fast rotators, in late 2014 and early 2015, five dedicated surveys covering ∼188 deg{sup 2} in the ecliptic plane have been carried out in the R -band, with ∼10 minute cadence using the intermediate Palomar Transient Factory. Among 1029 reliable rotation periods obtained from the surveys, we discovered 1 new large super-fast rotator, (40511) 1999 RE88, and 18 other candidates. (40511) 1999 RE88 is an S-type inner main-belt asteroid with a diameter of D  = 1.9 ± 0.3 km, a rotation period of P  = 1.96 ± 0.01 hr, and a light curve amplitude of Δ m  ∼ 1.0 mag. To maintainmore » such fast rotation, an internal cohesive strength of ∼780 Pa is required. Combining all known large super-fast rotators, their cohesive strengths all fall in the range of 100–1000 Pa of lunar regolith. However, the number of large super-fast rotators seems to be far less than the whole asteroid population. This might indicate a peculiar asteroid group for them. Although the detection efficiency for a long rotation period is greatly reduced due to our two-day observation time span, the spin-rate distributions of this work show consistent results with Chang et al. (2015), after considering the possible observational bias in our surveys. It shows a number decrease with an increase of spin rate for asteroids with a diameter of 3 ⩽  D  ⩽ 15 km, and a number drop at a spin rate of f  = 5 rev day{sup −1} for asteroids with D  ⩽ 3 km.« less

Mechanics of Fluid-Filled Interstitial Gaps. I. Modeling Gaps in a Compact Tissue.

PubMed

Parent, Serge E; Barua, Debanjan; Winklbauer, Rudolf

2017-08-22

Fluid-filled interstitial gaps are a common feature of compact tissues held together by cell-cell adhesion. Although such gaps can in principle be the result of weak, incomplete cell attachment, adhesion is usually too strong for this to occur. Using a mechanical model of tissue cohesion, we show that, instead, a combination of local prevention of cell adhesion at three-cell junctions by fluidlike extracellular material and a reduction of cortical tension at the gap surface are sufficient to generate stable gaps. The size and shape of these interstitial gaps depends on the mechanical tensions between cells and at gap surfaces, and on the difference between intracellular and interstitial pressures that is related to the volume of the interstitial fluid. As a consequence of the dependence on tension/tension ratios, the presence of gaps does not depend on the absolute strength of cell adhesion, and similar gaps are predicted to occur in tissues of widely differing cohesion. Tissue mechanical parameters can also vary within and between cells of a given tissue, generating asymmetrical gaps. Within limits, these can be approximated by symmetrical gaps. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Failure Prediction in Fiber Metal Laminates for Next Generation Aero Materials

NASA Astrophysics Data System (ADS)

Jeevan Rao, H.; Janaki Ramulu, Perumalla; Vishnu Vardhan, M.; Chandramouli, CH

2016-09-01

In aerospace industry, there is huge demand for low density and low cost materials with better mechanical properties. In this view, there are many researchers developed new materials interms of composites. Similar manner, the present paper also aimed to produce a new approach for cost effective materials of 3D weaved glass fiber metal laminates (FML) with different compositions using a numerical study. A method for the simulation of progressive delamination based on de-cohesion elements has been presented. De-cohesion elements are placed between layers of solid elements that open and shear in response to the loading situation. The onset of damage and the growth of delamination are simulated without previous knowledge about the location, the size, or the direction of propagation of the de-laminations. A softening law for mixed-mode delamination that can be applied to any interaction criterion is also proposed. The constitutive equation proposed uses a single variable, the maximum relative displacement, to track the damage at the interface under general loading conditions. The material properties required to define the element constitutive equation are the inter-laminar fracture toughness's, the penalty stiffness, and the strengths.

Study of budding yeast colony formation and its characterizations by using circular granular cell

NASA Astrophysics Data System (ADS)

Aprianti, D.; Haryanto, F.; Purqon, A.; Khotimah, S. N.; Viridi, S.

2016-03-01

Budding yeast can exhibit colony formation in solid substrate. The colony of pathogenic budding yeast can colonize various surfaces of the human body and medical devices. Furthermore, it can form biofilm that resists drug effective therapy. The formation of the colony is affected by the interaction between cells and with its growth media. The cell budding pattern holds an important role in colony expansion. To study this colony growth, the molecular dynamic method was chosen to simulate the interaction between budding yeast cells. Every cell was modelled by circular granular cells, which can grow and produce buds. Cohesion force, contact force, and Stokes force govern this model to mimic the interaction between cells and with the growth substrate. Characterization was determined by the maximum (L max) and minimum (L min) distances between two cells within the colony and whether two lines that connect the two cells in the maximum and minimum distances intersect each other. Therefore, it can be recognized the colony shape in circular, oval, and irregular shapes. Simulation resulted that colony formation are mostly in oval shape with little branch. It also shows that greater cohesion strength obtains more compact colony formation.

Tensile properties of cooked meat sausages and their correlation with texture profile analysis (TPA) parameters and physico-chemical characteristics.

PubMed

Herrero, A M; de la Hoz, L; Ordóñez, J A; Herranz, B; Romero de Ávila, M D; Cambero, M I

2008-11-01

The possibilities of using breaking strength (BS) and energy to fracture (EF) for monitoring textural properties of some cooked meat sausages (chopped, mortadella and galantines) were studied. Texture profile analysis (TPA), folding test and physico-chemical measurements were also performed. Principal component analysis enabled these meat products to be grouped into three textural profiles which showed significant (p<0.05) differences mainly for BS, hardness, adhesiveness and cohesiveness. Multivariate analysis indicated that BS, EF and TPA parameters were correlated (p<0.05) for every individual meat product (chopped, mortadella and galantines) and all products together. On the basis of these results, TPA parameters could be used for constructing regression models to predict BS. The resulting regression model for all cooked meat products was BS=-0.160+6.600∗cohesiveness-1.255∗adhesiveness+0.048∗hardness-506.31∗springiness (R(2)=0.745, p<0.00005). Simple linear regression analysis showed significant coefficients of determination between BS (R(2)=0.586, p<0.0001) versus folding test grade (FG) and EF versus FG (R(2)=0.564, p<0.0001).

Discrete dislocation plasticity analysis of loading rate-dependent static friction.

PubMed

Song, H; Deshpande, V S; Van der Giessen, E

2016-08-01

From a microscopic point of view, the frictional force associated with the relative sliding of rough surfaces originates from deformation of the material in contact, by adhesion in the contact interface or both. We know that plastic deformation at the size scale of micrometres is not only dependent on the size of the contact, but also on the rate of deformation. Moreover, depending on its physical origin, adhesion can also be size and rate dependent, albeit different from plasticity. We present a two-dimensional model that incorporates both discrete dislocation plasticity inside a face-centred cubic crystal and adhesion in the interface to understand the rate dependence of friction caused by micrometre-size asperities. The friction strength is the outcome of the competition between adhesion and discrete dislocation plasticity. As a function of contact size, the friction strength contains two plateaus: at small contact length [Formula: see text], the onset of sliding is fully controlled by adhesion while for large contact length [Formula: see text], the friction strength approaches the size-independent plastic shear yield strength. The transition regime at intermediate contact size is a result of partial de-cohesion and size-dependent dislocation plasticity, and is determined by dislocation properties, interfacial properties as well as by the loading rate.

Structural and mechanical properties of glassy water in nanoscale confinement.

PubMed

Lombardo, Thomas G; Giovambattista, Nicolás; Debenedetti, Pablo G

2009-01-01

We investigate the structure and mechanical properties of glassy water confined between silica-based surfaces with continuously tunable hydrophobicity and hydrophilicity by computing and analyzing minimum energy, mechanically stable configurations (inherent structures). The structured silica substrate imposes long-range order on the first layer of water molecules under hydrophobic confinement at high density (p > or = 1.0 g cm(-3)). This proximal layer is also structured in hydrophilic confinement at very low density (p approximately 0.4 g cm(-3)). The ordering of water next to the hydrophobic surface greatly enhances the mechanical strength of thin films (0.8 nm). This leads to a substantial stress anisotropy; the transverse strength of the film exceeds the normal strength by 500 MPa. The large transverse strength results in a minimum in the equation of state of the energy landscape that does not correspond to a mechanical instability, but represents disruption of the ordered layer of water next to the wall. In addition, we find that the mode of mechanical failure is dependent on the type of confinement. Under large lateral strain, water confined by hydrophilic surfaces preferentially forms voids in the middle of the film and fails cohesively. In contrast, water under hydrophobic confinement tends to form voids near the walls and fails by loss of adhesion.

Repair Bond Strength of Aged Resin Composite after Different Surface and Bonding Treatments

PubMed Central

Wendler, Michael; Belli, Renan; Panzer, Reinhard; Skibbe, Daniel; Petschelt, Anselm; Lohbauer, Ulrich

2016-01-01

The aim of this study was to compare the effect of different mechanical surface treatments and chemical bonding protocols on the tensile bond strength (TBS) of aged composite. Bar specimens were produced using a nanohybrid resin composite and aged in distilled water for 30 days. Different surface treatments (diamond bur, phosphoric acid, silane, and sandblasting with Al2O3 or CoJet Sand), as well as bonding protocols (Primer/Adhesive) were used prior to application of the repair composite. TBS of the specimens was measured and the results were analyzed using analysis of variance (ANOVA) and the Student–Newman–Keuls test (α = 0.05). Mechanically treated surfaces were characterized under SEM and by profilometry. The effect of water aging on the degree of conversion was measured by means of FTIR-ATR spectroscopy. An important increase in the degree of conversion was observed after aging. No significant differences in TBS were observed among the mechanical surface treatments, despite variations in surface roughness profiles. Phosphoric acid etching significantly improved repair bond strength values. The cohesive TBS of the material was only reached using resin bonding agents. Application of an intermediate bonding system plays a key role in achieving reliable repair bond strengths, whereas the kind of mechanical surface treatment appears to play a secondary role. PMID:28773669

Modeling of Stiffness and Strength of Bone at Nanoscale.

PubMed

Abueidda, Diab W; Sabet, Fereshteh A; Jasiuk, Iwona M

2017-05-01

Two distinct geometrical models of bone at the nanoscale (collagen fibril and mineral platelets) are analyzed computationally. In the first model (model I), minerals are periodically distributed in a staggered manner in a collagen matrix while in the second model (model II), minerals form continuous layers outside the collagen fibril. Elastic modulus and strength of bone at the nanoscale, represented by these two models under longitudinal tensile loading, are studied using a finite element (FE) software abaqus. The analysis employs a traction-separation law (cohesive surface modeling) at various interfaces in the models to account for interfacial delaminations. Plane stress, plane strain, and axisymmetric versions of the two models are considered. Model II is found to have a higher stiffness than model I for all cases. For strength, the two models alternate the superiority of performance depending on the inputs and assumptions used. For model II, the axisymmetric case gives higher results than the plane stress and plane strain cases while an opposite trend is observed for model I. For axisymmetric case, model II shows greater strength and stiffness compared to model I. The collagen-mineral arrangement of bone at nanoscale forms a basic building block of bone. Thus, knowledge of its mechanical properties is of high scientific and clinical interests.

Investigating the settling dynamics of cohesive silt particles with particle-resolving simulations

NASA Astrophysics Data System (ADS)

Sun, Rui; Xiao, Heng; Sun, Honglei

2018-01-01

The settling of cohesive sediment is ubiquitous in aquatic environments, and the study of the settling process is important for both engineering and environmental reasons. In the settling process, the silt particles show behaviors that are different from non-cohesive particles due to the influence of inter-particle cohesive force. For instance, the flocs formed in the settling process of cohesive silt can loosen the packing, and thus the structural densities of cohesive silt beds are much smaller than that of non-cohesive sand beds. While there is a consensus that cohesive behaviors depend on the characteristics of sediment particles (e.g., Bond number, particle size distribution), little is known about the exact influence of these characteristics on the cohesive behaviors. In addition, since the cohesive behaviors of the silt are caused by the inter-particle cohesive forces, the motions of and the contacts among silt particles should be resolved to study these cohesive behaviors in the settling process. However, studies of the cohesive behaviors of silt particles in the settling process based on particle-resolving approach are still lacking. In the present work, three-dimensional settling process is investigated numerically by using CFD-DEM (Computational Fluid Dynamics-Discrete Element Method). The inter-particle collision force, the van der Waals force, and the fluid-particle interaction forces are considered. The numerical model is used to simulate the hindered settling process of silt based on the experimental setup in the literature. The results obtained in the simulations, including the structural densities of the beds, the characteristic lines, and the particle terminal velocity, are in good agreement with the experimental observations in the literature. To the authors' knowledge, this is the first time that the influences of non-dimensional Bond number and particle polydispersity on the structural densities of silt beds have been investigated separately. The results demonstrate that the cohesive behavior of silt in the settling process is attributed to both the cohesion among silt particles themselves and the particle polydispersity. To guide to the macro-scale modeling of cohesive silt sedimentation, the collision frequency functions obtained in the numerical simulations are also presented based on the micromechanics of particles. The results obtained by using CFD-DEM indicate that the binary collision theory over-estimated the particle collision frequency in the flocculation process at high solid volume fraction.

Supporting students' learning in the domain of computer science

NASA Astrophysics Data System (ADS)

Gasparinatou, Alexandra; Grigoriadou, Maria

2011-03-01

Previous studies have shown that students with low knowledge understand and learn better from more cohesive texts, whereas high-knowledge students have been shown to learn better from texts of lower cohesion. This study examines whether high-knowledge readers in computer science benefit from a text of low cohesion. Undergraduate students (n = 65) read one of four versions of a text concerning Local Network Topologies, orthogonally varying local and global cohesion. Participants' comprehension was examined through free-recall measure, text-based, bridging-inference, elaborative-inference, problem-solving questions and a sorting task. The results indicated that high-knowledge readers benefited from the low-cohesion text. The interaction of text cohesion and knowledge was reliable for the sorting activity, for elaborative-inference and for problem-solving questions. Although high-knowledge readers performed better in text-based and in bridging-inference questions with the low-cohesion text, the interaction of text cohesion and knowledge was not reliable. The results suggest a more complex view of when and for whom textual cohesion affects comprehension and consequently learning in computer science.

Effect of Various Laser Surface Treatments on Repair Shear Bond Strength of Aged Silorane-Based Composite

PubMed Central

Alizadeh Oskoee, Parnian; Savadi Oskoee, Siavash; Rikhtegaran, Sahand; Pournaghi-Azar, Fatemeh; Gholizadeh, Sarah; Aleyasin, Yasaman; Kasrae, Shahin

2017-01-01

Introduction: Successful repair of composite restorations depends on a strong bond between the old composite and the repair composite. This study sought to assess the repair shear bond strength of aged silorane-based composite following surface treatment with Nd:YAG, Er,Cr:YSGG and CO2 lasers. Methods: Seventy-six Filtek silorane composite cylinders were fabricated and aged by 2 months of water storage at 37°C. The samples were randomly divided into 4 groups (n=19) of no surface treatment (group 1) and surface treatment with Er,Cr:YSGG (group 2), Nd:YAG (group 3) and CO2 (group 4) lasers. The repair composite was applied and the shear bond strength was measured. The data were analyzed using one-way analysis of variance (ANOVA) and Tukey posthoc test. Prior to the application of the repair composite, 2 samples were randomly selected from each group and topographic changes on their surfaces following laser irradiation were studied using a scanning electron microscope (SEM). Seventeen other samples were also fabricated for assessment of cohesive strength of composite. Results: The highest and the lowest mean bond strength values were 8.99 MPa and 6.69 MPa for Er,Cr:YSGG and control groups, respectively. The difference in the repair bond strength was statistically significant between the Er,Cr:YSGG and other groups. Bond strength of the control, Nd:YAG and CO2 groups was not significantly different. The SEM micrographs revealed variable degrees of ablation and surface roughness in laser-treated groups. Conclusion: Surface treatment with Er,Cr:YSGG laser significantly increase the repair bond strength of aged silorane-based composite resin. PMID:29071025

The Development and Use of Cohesive Devices in L2 Writing and Their Relations to Judgments of Essay Quality

ERIC Educational Resources Information Center

Crossley, Scott A.; Kyle, Kristopher; McNamara, Danielle S.

2016-01-01

An important topic in writing research has been the use of cohesive features. Much of this research has focused on local and text cohesion. The few studies that have studied global cohesion have been restricted to first language writing. This study investigates the development of local, global, and text cohesion in the writing of 57 language (L2)…

The Efficacy of ’Don’t Ask, Don’t Tell’

DTIC Science & Technology

2009-01-01

psychologists explored the concepts, experimental and cor- relation evidence supported dividing cohesion into two distinct types: social cohesion and task...cohesion. Social cohesion is the nature and quality of the emotional bonds within a group—the degree to which members spend time together, like...along (that is, has high social cohesion ) would perform better. Almost counterintuitively, it has been shown that in some situations, high social

The Impact of Drug Abuse on Tank Crew Cohesion.

DTIC Science & Technology

1982-08-01

social cohesion ). Examination ef modal scores on the Cohesion Questions indicated that similarity or difference in drug use pattern influenced the...demography, drug use and social cohesion . The AFFIL scores were divided into two groups: Hi AFFEL and Lo AFFIL. The Hi AFFIL group was comprised of...difference in usage pattern, the social cohesion questions were slightly more sensitive to simple similarity in drug use pattern than the job-related

Outdoor activities and depressive symptoms in displaced older adults following natural disaster: community cohesion as mediator and moderator.

PubMed

Chao, Shiau-Fang

2016-09-01

This investigation examined whether community cohesion mediates or moderates the relationship between outdoor activities and depressive symptoms in older adults displaced by Typhoon Morakot in Taiwan. This cross-sectional study included 292 adults aged 65 years or older who were relocated to permanent houses after Typhoon Morakot damaged their homes on 8th August 2009. Multiple regression analysis was applied to test the role of community cohesion on the association between outdoor activities and depressive symptoms. The sample of displaced older adults displayed higher prevalence of depressive symptoms than the average for community dwelling older people in Taiwan. Community cohesion fully mediated the relationship between outdoor activities and depressive symptoms. Community cohesion also moderated the relationship between outdoor activities and depressive symptoms. Community cohesion occupies a key role on the link between outdoor activities and depressive symptoms. Participation in outdoor activities was associated positively with community cohesion, while high community cohesion was related negatively to depressive symptoms. Additionally, the benefit of outdoor activities to fewer depressive symptoms only manifested in older adults with high community cohesion. Programs and services should be designed to enhance community cohesion in order to maximize the benefit of outdoor activities to the mental health of displaced older adults after natural disasters.

Spilling over: Partner parenting stress as a predictor of family cohesion in parents of adolescents with developmental disabilities.

PubMed

Mitchell, Darcy B; Szczerepa, Alexandra; Hauser-Cram, Penny

2016-01-01

Family cohesion relates to positive outcomes for both parents and children. Maintaining cohesion may be especially challenging for families of adolescents with developmental disabilities, yet this has been studied infrequently in this group. We investigated cohesion in these families, particularly with respect to partner stress, using the notion of the 'spillover effect' as a model. Adolescents with disabilities and their parents participated. Parents reported on teen adaptive and problem behaviours and on marital satisfaction, parenting stress, and family cohesion. The stress of one partner was tested as a predictor of the quality of family cohesion reported by the other. Adolescent behaviour problems were negative predictors of family cohesion in mothers, and marital satisfaction positively predicted cohesion for both parents. Above other factors, greater partner stress predicted poorer family cohesion for both fathers and mothers. Marital satisfaction acted as a suppressor of this relation. To improve the overall climate of families, care providers should take into consideration individual relationships, including the marital relationship. In addition, the possibility of spillover from one individual to another should be recognized as a factor in family functioning. Family-centred practices are likely to lead to greater feelings of cohesion and overall better individual and family well-being. Copyright © 2015 Elsevier Ltd. All rights reserved.

Physical properties of muddy sediments from French Guiana

NASA Astrophysics Data System (ADS)

Caillaud, J.; Lesourd, L.; Philippe, S.; Gontharet, S.; Sarrazin, M.; Gardel, A.

2017-01-01

The North West migration of long and discontinuous mud banks along the French Guiana coast has been extensively studied during the past years, in particular with a large-scale vision, which consequently has integrated morpho and hydrodynamic data. The aims of the present paper were to use intrinsic sediment properties (grain-size, mineralogy, concentration, and cohesion) to (1) highlight the sedimentary conditions during the consolidation processes from fluid deposit to vegetation development, and (2) verify the apparent homogeneously derived sedimentary facies. Two intertidal transects, Macouria and Cayenne, were compared from the coast to offshore. Their altitude averages of 1 m and 2.8 m above mean sea level, respectively, were different enough to compare the influence of the hydrodynamic impact and emersion time on their sediment properties. The latter, i.e. grain size distribution, mineralogical content, mud concentration, and shear strength (cohesion), were determined from sampled surface sediments (first cm) and along sediment cores (20-30 cm depth) from each transect. A specific X-ray technique was applied to the whole core to differentiate clearly its thin layers. On both intertidal sites, the grain size dominated by the fine silt fraction (2-20 μm) and the bulk mineralogy characterized by five major minerals (quartz, feldspars, chlorite, illite, and kaolinite) appeared homogeneous along both transects and cores. In spite of this apparent uniformity of particle size and mineralogical parameters, as well as for visual observation along the core, high precision X-rays still showed a cyclic sedimentation at a micro-scale level. This cyclicity with intercalation of fine layers was related to distinct dynamic deposits marked by both tidal processes and hydrodynamic factors (swell propagation). The cohesion and concentration results were dependent on the topography, where high topography was characterized by sediments with high cohesion and concentration values, and vice versa. A comparison between these two parameters was done to define critical limits between soft and stiff muds, as well as unvegetated and colonized muds. The favorable intrinsic sedimentary properties for consolidation and colonization were also discussed according to the field observations and bibliographic data.

Written cohesion in children with and without language learning disabilities.

PubMed

Koutsoftas, Anthony D; Petersen, Victoria

2017-09-01

Cohesion refers to the linguistic elements of discourse that contribute to its continuity and is an important element to consider as part of written language intervention, especially in children with language learning disabilities (LLD). There is substantial evidence that children with LLD perform more poorly than typically developing (TD) peers on measures of cohesion in spoken language and on written transcription measures; however, there is far less research comparing groups on cohesion as a measure of written language across genres. The current study addresses this gap through the following two aims. First, to describe and compare cohesion in narrative and expository writing samples of children with and without language learning disabilities. Second, to relate measures of cohesion to written transcription and translation measures, oral language, and writing quality. Fifty intermediate-grade children produced one narrative and one expository writing sample from which measures of written cohesion were obtained. These included the frequency, adequacy and complexity of referential and conjunctive ties. Expository samples resulted in more complex cohesive ties and children with TD used more complex ties than peers with LLD. Different relationships among cohesion measures and writing were observed for narrative verse expository samples. Findings from this study demonstrate cohesion as a discourse-level measure of written transcription and how the use of cohesion can vary by genre and group (LLD, TD). Clinical implications for assessment, intervention, and future research are provided. © 2016 Royal College of Speech and Language Therapists.

Influence of group cohesion on maternal well-being among participants in a support/education group program for single mothers.

PubMed

Lipman, Ellen L; Waymouth, Marjorie; Gammon, Tara; Carter, Patricia; Secord, Margaret; Leung, Olivia; Mills, Brenda; Hicks, Frances

2007-10-01

Single mothers are at increased risk of psychosocial disadvantage, social isolation and physical and mental health difficulties. The authors present (1) the results of group cohesion assessments completed by mothers participating in a trial of community-based support/education groups, and (2) assessments of the association between group cohesion ratings and intervention outcomes of maternal self-evaluations of well-being (mood, self-esteem, and social support) and parenting. Mothers participating in groups completed the Group Atmosphere Scale, a measure of group cohesion, post-group. Overall, most participants provided strong ratings of group cohesion. Significant associations were found between group cohesion and specific positive outcomes. This suggests a positive association between group cohesion and mood, self-esteem, social support, and parenting, in this trial.

Microscopic mechanism of amino silicone oil modification and modification effect with different amino group contents based on molecular dynamics simulation

NASA Astrophysics Data System (ADS)

He, Liping; Li, Wenjun; Chen, Dachuan; Yuan, Jianmin; Lu, Gang; Zhou, Dianwu

2018-05-01

The microscopic mechanism of amino silicone oil (ASO) modification of natural fiber was investigated for the first time using molecular dynamics (MD) simulation at the atomic and molecular levels. The MD simulation results indicated that the ASO molecular interacted with the cellulose molecular within the natural fiber, mainly by intermolecular forces of Nsbnd Hsbnd O and Osbnd Hsbnd N hydrogen bonds and the molecular chain of ASO absorbed onto the natural fiber in a selective orientation, i.e., the hydrophobic alkyl groups (sbnd CnH2n+1) project outward and the polar amino groups (sbnd NH2) point to the surface of natural fiber. Consequently, the ASO modification changed the surface characteristic of natural fiber from hydrophilic to hydrophobic. Furthermore, the modification effects of the ASO modification layer with different amino group contents (m:n ratio) were also evaluated in this study by calculating the binding energy between the ASO modifier and natural fiber, and the cohesive energy density and free volume of the ASO modification layer. The results showed that the binding energy reached a maximum when the m:n ratio of ASO was of 8:4, suggesting that a good bonding strength was achieved at this m:n ratio. It was also found that the cohesive energy density enhanced with the increase in the amino group content, and the higher the cohesive energy density, the easier the formation of the ASO modification layer. However, the fraction free volume decreased with the increase in the amino group content. This is good for improving the water-proof property of natural fiber. The present work can provide an effective method for predicting the modification effects and designing the optimized m:n ratio of ASO modification.

On crack initiation in notched, cross-plied polymer matrix composites

NASA Astrophysics Data System (ADS)

Yang, Q. D.; Schesser, D.; Niess, M.; Wright, P.; Mavrogordato, M. N.; Sinclair, I.; Spearing, S. M.; Cox, B. N.

2015-05-01

The physics of crack initiation in a polymer matrix composite are investigated by varying the modeling choices made in simulations and comparing the resulting predictions with high-resolution in situ images of cracks. Experimental data were acquired using synchrotron-radiation computed tomography (SRCT) at a resolution on the order of 1 μm, which provides detailed measurement of the location, shape, and size of small cracks, as well as the crack opening and shear displacements. These data prove sufficient to discriminate among competing physical descriptions of crack initiation. Simulations are executed with a high-fidelity formulation, the augmented finite element method (A-FEM), which permits consideration of coupled damage mechanisms, including both discrete cracks and fine-scale continuum damage. The discrete cracks are assumed to be nonlinear fracture events, governed by reasonably general mixed-mode cohesive laws. Crack initiation is described in terms of strength parameters within the cohesive laws, so that the cohesive law provides a unified model for crack initiation and growth. Whereas the cracks investigated are typically 1 mm or less in length, the fine-scale continuum damage refers to irreversible matrix deformation occurring over gauge lengths extending down to the fiber diameter (0.007 mm). We find that the location and far-field stress for crack initiation are predicted accurately only if the variations of local stress within plies and in the presence of stress concentrators (notches, etc.) are explicitly computed and used in initiation criteria; stress redistribution due to matrix nonlinearity that occurs prior to crack initiation is accounted for; and a mixed-mode criterion is used for crack initiation. If these factors are not all considered, which is the case for commonly used failure criteria, predictions of the location and far-field stress for initiation are not accurate.

Neighbourhood cohesion and mental wellbeing among older adults: a mixed methods approach.

PubMed

Elliott, Jane; Gale, Catharine R; Parsons, Samantha; Kuh, Diana

2014-04-01

There is now a body of evidence that demonstrates strong links between neighbourhood characteristics and mental health and wellbeing. There is an increasing interest in how this relationship varies for individuals of different ages. Understanding the link between neighbourhood and wellbeing for older adults is of particular significance, given the changing age structure of the population and the desire among policy makers and practitioners to promote healthy and active ageing. This paper provides further evidence on the nature and strength of the link between individual perceptions of neighbourhood belonging and mental wellbeing among those over age fifty using both qualitative and quantitative data from three British cohort studies. Between 2008 and 2011 quantitative data were collected from 10,312 cohort members, and 230 of them took part in qualitative biographical interviews. Quantitative analysis confirms that there is a moderate association between neighbourhood cohesion and wellbeing measured at the individual level in each of the three cohorts. This association persists after controlling for a range of covariates including personality. The association between neighbourhood cohesion and wellbeing is stronger for individuals in the older two cohorts than in the younger cohort. Using qualitative biographical interviews with 116 men and 114 women we illustrate how individuals talk about their sense of neighbourhood belonging. The importance of social participation as a mechanism for promoting neighbourhood belonging, and the use of age and life stage as characteristics to describe and define neighbours, is clear. In addition, the qualitative interviews point to the difficulties of using a short battery of questions to capture the varied and multi-dimensional nature of neighbourhood relations. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Social cohesion matters in health

PubMed Central

2013-01-01

Introduction The concept of social cohesion has invoked debate due to the vagueness of its definition and the limitations of current measurements. This paper attempts to examine the concept of social cohesion, develop measurements, and investigate the relationship between social cohesion and individual health. Methods This study used a multilevel study design. The individual-level samples from 29 high-income countries were obtained from the 2000 World Value Survey (WVS) and the 2002 European Value Survey. National-level social cohesion statistics were obtained from Organization of Economic Cooperation and Development datasets, World Development Indicators, and Asian Development Bank key indicators for the year 2000, and from aggregating responses from the WVS. In total 47,923 individuals were included in this study. The factor analysis was applied to identify dimensions of social cohesion, which were used as entities in the cluster analysis to generate a regime typology of social cohesion. Then, multilevel regression models were applied to assess the influences of social cohesion on an individual’s self-rated health. Results and discussion Factor analysis identified five dimensions of social cohesion: social equality, social inclusion, social development, social capital, and social diversity. Then, the cluster analysis revealed five regimes of social cohesion. A multi-level analysis showed that respondents in countries with higher social inclusion, social capital, and social diversity were more likely to report good health above and beyond individual-level characteristics. Conclusions This study is an innovative effort to incorporate different aspects of social cohesion. This study suggests that social cohesion was associated with individual self-rated after controlling individual characteristics. To achieve further advancement in population health, developed countries should consider policies that would foster a society with a high level of social inclusion, social capital, and social diversity. Future research could focus on identifying possible pathways by which social cohesion influences various health outcomes. PMID:24165541

Factors Related to Group Cohesiveness.

ERIC Educational Resources Information Center

Roark, Albert E.; Sharah, Hussein S.

1989-01-01

Investigated the relationship of group cohesiveness to empathy, self-disclosure, acceptance, and trust, and compared three different groups (personal growth, driving under the influence, psychotherapy), with a total of 65 subjects, on measures of cohesiveness. Found all factors correlated significantly with cohesiveness and with one another.…

Alcohol Use Severity Among Adult Hispanic Immigrants: Examining the Roles of Family Cohesion, Social Support, and Gender.

PubMed

Cano, Miguel Ángel; Sánchez, Mariana; Rojas, Patria; Ramírez-Ortiz, Daisy; Polo, Katherine L; Romano, Eduardo; De La Rosa, Mario

2018-03-21

This study examined (a) the direct association of family cohesion on alcohol use severity among adult Hispanic immigrants; (b) the indirect association of family cohesion on alcohol use severity via social support; and (c) if gender moderates the direct and indirect associations between family cohesion and alcohol use severity. Mediation and moderation analyses were conducted on a cross-sectional sample of 411 (men = 222, women = 189) participants from Miami-Dade, Florida. Findings indicate that higher family cohesion was directly associated with higher social support and lower alcohol use severity. Higher social support was also directly associated with lower alcohol use severity. Additionally, family cohesion had an indirect association with alcohol use severity via social support. Moderation analyses indicated that gender moderated the direct association between family cohesion and alcohol use severity, but did not moderate the indirect association. Some potential clinical implications may be that strengthening family cohesion may enhance levels of social support, and in turn, lower alcohol use severity among adult Hispanic immigrants. Furthermore, strengthening family cohesion may be especially beneficial to men in efforts to lower levels of alcohol use severity.

A sign of the times: To have or to be? Social capital or social cohesion?

PubMed

Carrasco, Maria A; Bilal, Usama

2016-06-01

Among various social factors associated with health behavior and disease, social cohesion has not captured the imagination of public health researchers as much as social capital as evidenced by the subsuming of social cohesion into social capital and the numerous studies analyzing social capital and the comparatively fewer articles analyzing social cohesion and health. In this paper we provide a brief overview of the evolution of the conceptualization of social capital and social cohesion and we use philosopher Erich Fromm's distinction between "having" and "being" to understand the current research focus on capital over cohesion. We argue that social capital is related to having while social cohesion is related to being and that an emphasis on social capital leads to individualizing tendencies that are antithetical to cohesion. We provide examples drawn from the literature where this conflation of social capital and cohesion results in non-concordant definitions and subsequent operationalization of these constructs. Beyond semantics, the practical implication of focusing on "having" vs. "being" include an emphasis on understanding how to normalize groups and populations rather than providing those groups space for empowerment and agency leading to health. Published by Elsevier Ltd.

Towards a universal description of cohesive-particle flows

NASA Astrophysics Data System (ADS)

Lamarche, Casey; Liu, Peiyuan; Kellogg, Kevin; Lattanzi, Aaron; Hrenya, Christine

2017-11-01

A universal framework for describing cohesive granular flows seems unattainable based on prior works, making a fundamental continuum theory to predict such flows appear unachievable. For the first time, universal behavior of cohesive-grain flows is demonstrated by linking the macroscopic (many-grain) behavior to grain-grain interactions via two dimensionless groups: a generalized Bond number BoG - ratio of maximum cohesive force to the force driving flow - and a new Agglomerate number Ag - ratio of critical cohesive energy to the granular energy. Cohesive-grain flow is investigated in several systems, and universal behavior is determined via collapse of a cohesion-dependent output variable from each system with the appropriate dimensionless group. Universal behavior is observed using BoG for dense (enduring-contact-dominated) flows and Ag for dilute (collision-dominated) flows, as BoG accounts for the cohesive contact force and Ag for increased collisional dissipation due to cohesion. Hence, a new physical picture is presented, namely, BoG dominates in dense flows, where force chains drive momentum transfer, and Ag dominates in dilute systems, where the dissipative collisions dominate momentum transfer. Apparent discrepancies with past treatments are resolved. Dow Corning Corporation.

Don’t Ask, Don’t Tell: Failing in Strategic Leadership

DTIC Science & Technology

2007-03-30

another example of where the results might be useful. Even if 7 one accepts the fact that task cohesion overrides social cohesion as a major...it can be inferred that social cohesion is still an important factor in combat. At this point the important question becomes whether openly gay...Gateway, 1993), 57. 17 39 Social cohesion refers to emotional bonds and friendship, and is distinguished from task cohesion which refers to a group’s

Interactive effects of team cohesion on perceived efficacy in semi-professional sport.

PubMed

Marcos, Francisco Miguel Leo; Miguel, Pedro Antonio Sánchez; Oliva, David Sánchez; Calvo, Tomás García

2010-01-01

The present study examined the relationships among cohesion, self-efficacy, coaches' perceptions of their players' efficacy at the individual level and athletes' perceptions of their teammates' efficacy. Participants (n = 76) recruited from four semi- professional soccer and basketball teams completed cohesiveness and efficacy questionnaires who. Data were analyzed through a correlational methodology. Results indicated significant correlations between self-efficacy and task cohesion and social cohesion. Regression analysis results suggest task cohesion positively related to coaches and teammate's perception of efficacy. These results have implications for practitioners in terms of the importance of team building to enhance team cohesion and feelings of efficacy. Key pointsThis paper increases the knowledge about soccer and basketball match analysis.Give normative values to establish practice and match objectives.Give applications ideas to connect research with coaches' practice.

Modeling reciprocal team cohesion-performance relationships, as impacted by shared leadership and members' competence.

PubMed

Mathieu, John E; Kukenberger, Michael R; D'Innocenzo, Lauren; Reilly, Greg

2015-05-01

Despite the lengthy history of team cohesion-performance research, little is known about their reciprocal relationships over time. Using meta-analysis, we synthesize findings from 17 CLP design studies, and analyze their results using SEM. Results support that team cohesion and performance are related reciprocally with each other over time. We then used longitudinal data from 205 members of 57 student teams who competed in a complex business simulation over 10 weeks, to test: (a) whether team cohesion and performance were related reciprocally over multiple time periods, (b) the relative magnitude of those relationships, and (c) whether they were stable over time. We also considered the influence of team members' academic competence and degree of shared leadership on these dynamics. As anticipated, cohesion and performance were related positively, and reciprocally, over time. However, the cohesion → performance relationship was significantly higher than the performance → cohesion relationship. Moreover, the cohesion → performance relationship grew stronger over time whereas the performance → cohesion relationship remained fairly consistent over time. As expected, shared leadership related positively to team cohesion but not directly to their performance; whereas average team member academic competence related positively to team performance but was unrelated to team cohesion. Finally, we conducted and report a replication using a second sample of students competing in a business simulation. Our earlier substantive relationships were mostly replicated, and we illustrated the dynamic temporal properties of shared leadership. We discuss these findings in terms of theoretical importance, applied implications, and directions for future research. (c) 2015 APA, all rights reserved.

Intact Discourse Cohesion and Coherence Following Bilateral Ventromedial Prefrontal Cortex

ERIC Educational Resources Information Center

Kurczek, Jake; Duff, Melissa C.

2012-01-01

Discourse cohesion and coherence give communication its continuity providing the grammatical and lexical links that hold an utterance or text together and give it meaning. Researchers often link cohesion and coherence deficits to the frontal lobes by drawing attention to frontal lobe dysfunction in populations where discourse cohesion and…

Nonequivalent Associations between Forms of Cohesiveness and Group-Related Outcomes: Evidence for Multidimensionality.

ERIC Educational Resources Information Center

Zaccaro, Stephen J.

1991-01-01

Presents results of a study contrasting different forms of group cohesiveness in a student military organization. Reports that task cohesiveness was more strongly associated with lower role uncertainty, higher individual performance, and lower absenteeism than was interpersonal cohesiveness. Concludes that data provide evidence for a…

Building a Board that Sticks Together

ERIC Educational Resources Information Center

Wilson, E. B.

2006-01-01

High-performing boards operating at a distinguishable level of excellence, all exhibit a culture of cohesiveness. And a compelling codicil is that these boards did not deliberately set out to become cohesive and perhaps do not even know they are cohesive. This article examines the value of cohesion to university governing boards, explicitly…

Soldiers Have to Eat Soup Together for a Long Time

DTIC Science & Technology

2007-03-10

negatively impacted unit cohesion. The definition of cohesion used for this project is that of “ social cohesion ” or trust based on shared successes...fight.” 9 Napoleon was referring to social cohesion or trust based on shared successes during training and operations. The DoD’s mobilization

CrossTalk, The Journal of Defense Software Engineering. Volume 28 Number 1. Jan/Feb 2015

DTIC Science & Technology

2015-02-01

5.63 1.03 Positive Gain 1.19 42% 1.10 27% 1.20 31% 0.44 12% Table 7. Group 1 & 2 Pretest and Posttest Means and Gain Scores. The one ...linked to team performance [6][7][8] and is considered one of the most important small group variables [9] with cohesion-performance being driven by...increased team cohesion. Measuring Cohesion In order to measure team cohesion, one must first understand the correlated cohesion constructs. The Group

The Role of Natural Hydrate on the Strength of Sands: Load-bearing or Cementing?

NASA Astrophysics Data System (ADS)

Priest, J. A.; Hayley, J. L.

2017-12-01

The strength of hydrate bearing sands is a key parameter for simulating the long-term performance of hydrate reservoirs during gas production and assessing reservoir and wellbore stability. Historically this parameter has been determined from testing synthesized hydrate sand samples, which has led to significant differences in measured strength that appears to reflect different formation methods adopted. At present, formation methods can be grouped into either those that form hydrate at grain contacts leading to a high strength `cemented' sand, or those where the hydrate forms a `load-bearing' structure in which the hydrate grains reside in the pore space resulting in more subtle changes in strength. Recovered natural hydrate-bearing cores typically exhibit this `load-bearing' behavior, although these cores have generally undergone significant changes in temperature and pressure during recovery, which may have altered the structure of the hydrate and sediment. Recent drilling expeditions using pressure coring, such as NGHP2 offshore India, have enabled intact hydrate bearing sediments to be recovered that have maintained hydrostatic stresses minimizing any changes in the hydrate structure within the core. Triaxial testing on these samples highlight enhanced strength even at zero effective stresses. This suggests that the hydrate forms a connected framework within the pore space apparently `cementing' the sand grains in place: we differentiate here between true cementation where hydrate is sintered onto the sand grains and typical observed behavior for cemented sands (cohesion, peak strength, post-peak strain softening). This inter-connected hydrate, and its ability to increase strength of the sands, appears to occur even at hydrate saturations as low as 30%, where typical `load-bearing' hydrates just start to increase strength. The results from pressure cores suggest that hydrate formation techniques that lead to `load-bearing' behavior may not capture the true interaction between the hydrate and sand and thus further research is needed to form synthesized hydrate bearing samples that more realistically mimic the observed strength behavior of natural hydrate bearing cores.

Laser-tissue soldering with biodegradable polymer films in vitro: film surface morphology and hydration effects.

PubMed

Sorg, B S; Welch, A J

2001-01-01

Previous research introduced the concept of using biodegradable polymer film reinforcement of a liquid albumin solder for improvement of the tensile strength of repaired incisions in vitro. In this study, the effect of creating small pores in the PLGA films on the weld breaking strength is studied. Additionally, the effect of hydration on the strength of the reinforced welds is investigated. A 50%(w/v) bovine serum albumin solder with 0.5 mg/mL Indocyanine Green dye was used to repair an incision in bovine aorta. The solder was coagulated with an 806-nm CW diode laser. A poly(DL-lactic-co-glycolic acid) (PLGA) film was used to reinforce the solder (the controls had solder but no reinforcement). Breaking strengths were measured acutely and after hydration in saline for 1 and 2 days. The data were analyzed by ANOVA (P < 0.05) and multiple comparisons of means were performed using the Newman-Keuls test. The creation of pores in the PLGA films qualitatively improved the film flexibility without having an apparent adverse effect on the breaking strength, while the actual technique of applying the film and solder had more of an effect. The acute maximum average breaking strengths of some of the film reinforced specimens (114.7 g-134.4 g) were significantly higher (P < 0.05) than the acute maximum average breaking strength of the unreinforced control specimens (68.3 g). Film reinforced specimens were shown to have a statistically significantly higher breaking strength than unreinforced controls after 1- and 2-day hydration. Reinforcement of liquid albumin solders in laser-assisted incision repair appears to have advantages over conventional methods that do not reinforce the cohesive strength of the solder in terms of acute breaking strength and after immersion in moist environments for short periods of time. Using a film with the solder applied to one surface only may be advantageous over other techniques.

Push-out bond strength of fiber posts to root dentin using glass ionomer and resin modified glass ionomer cements.

PubMed

Pereira, Jefferson Ricardo; Rosa, Ricardo Abreu da; Só, Marcus Vinícius Reis; Afonso, Daniele; Kuga, Milton Carlos; Honório, Heitor Marques; Valle, Accácio Lins do; Vidotti, Hugo Alberto

2014-01-01

The purpose of this study was to assess the push-out bond strength of glass fiber posts to root dentin after cementation with glass ionomer (GICs) and resinmodified glass ionomer cements (RMGICs). Fifty human maxillary canines were transversally sectioned at 15 mm from the apex. Canals were prepared with a step back technique until the application of a #55 K-file and filled. Post spaces were prepared and specimens were divided into five groups according to the cement used for post cementation: Luting & Lining Cement; Fuji II LC Improved; RelyX Luting; Ketac Cem; and Ionoseal. After cementation of the glass fiber posts, all roots were stored at 100% humidity until testing. For push-out test, 1-mm thick slices were produced. The push-out test was performed in a universal testing machine at a crosshead speed of 0.5 mm/minute and the values (MPa) were analyzed by Kolmogorov-Smirnov and Levene's tests and by two-way ANOVA and Tukey's post hoc test at a significance level of 5%. Fiber posts cemented using Luting & Lining Cement, Fuji II LC Improved, and Ketac Cem presented the highest bond strength to root dentin, followed by RelyX Luting. Ionoseal presented the lowest bond strength values (P>0.05). The post level did not influence the bond strength of fiber posts to root dentin (P=0.148). The major cause of failure was cohesive at the cement for all GICs and RMGICs. Except for Ionoseal, all cements provided satisfactory bond strength values.

On the Bonding Strength of Fe-Based Self-Fluxing Alloy Coating Deposited by Different Methods on the Steel Substrate

NASA Astrophysics Data System (ADS)

Feldshtein, E.; Kardapolava, M.; Dyachenko, O.

2018-05-01

In the present paper, the bonding strength of Fe-based self-fluxing alloy coating deposited by plasma spraying, gluing and laser remelting and alloying on the steel substrate have been investigated. When flame melting, a globular structure is formed. Against the background of the solid solution carbide-boride phases are clearly distinguishable, between which the Fe-Fe2B and Fe-FeB eutectic colonies are situated. Laser remelting leads to the formation of metastable structures, reinforced with dendrites, consisting of alloyed Fe-α and Fe-γ. At the low laser beam speeds the coating is melted completely with the formation of a cast structure with the dendrites. When the laser beam speed is increased, the dendritic structure gets fragmented. Structures of coatings alloyed with B4C and remelted by the laser beam vary with the increase of the spot speed. The bonding strength of coating without subsequent remelting decreases by 4-5 times in comparison with remelted. The bonding strength of the reinforced glue coating has adhesive and adhesive-cohesive character. When the load increases in the coating, microcracks develop, which gradually spread to the center of the bonding surface. For plasma coatings after laser remelting without additional alloying, the maximum bonding strength is observed with the minimum laser beam speed. With increasing the laser beam speed it decreases almost 1.5 times. In glue coatings reinforced with B4C particulates by laser remelting, the bonding strength is lower by 1.2-1.4 times in comparison with plasma coating.

Push-out bond strength of fiber posts to root dentin using glass ionomer and resin modified glass ionomer cements

PubMed Central

PEREIRA, Jefferson Ricardo; da ROSA, Ricardo Abreu; SÓ, Marcus Vinícius Reis; AFONSO, Daniele; KUGA, Milton Carlos; HONÓRIO, Heitor Marques; do VALLE, Accácio Lins; VIDOTTI, Hugo Alberto

2014-01-01

Objective The purpose of this study was to assess the push-out bond strength of glass fiber posts to root dentin after cementation with glass ionomer (GICs) and resin-modified glass ionomer cements (RMGICs). Material and Methods Fifty human maxillary canines were transversally sectioned at 15 mm from the apex. Canals were prepared with a step back technique until the application of a #55 K-file and filled. Post spaces were prepared and specimens were divided into five groups according to the cement used for post cementation: Luting & Lining Cement; Fuji II LC Improved; RelyX Luting; Ketac Cem; and Ionoseal. After cementation of the glass fiber posts, all roots were stored at 100% humidity until testing. For push-out test, 1-mm thick slices were produced. The push-out test was performed in a universal testing machine at a crosshead speed of 0.5 mm/minute and the values (MPa) were analyzed by Kolmogorov-Smirnov and Levene's tests and by two-way ANOVA and Tukey's post hoc test at a significance level of 5%. Results Fiber posts cemented using Luting & Lining Cement, Fuji II LC Improved, and Ketac Cem presented the highest bond strength to root dentin, followed by RelyX Luting. Ionoseal presented the lowest bond strength values (P>0.05). The post level did not influence the bond strength of fiber posts to root dentin (P=0.148). The major cause of failure was cohesive at the cement for all GICs and RMGICs. Conclusions Except for Ionoseal, all cements provided satisfactory bond strength values. PMID:25004052

In vitro tensile bond strength of adhesive cements to new post materials.

PubMed

O'Keefe, K L; Miller, B H; Powers, J M

2000-01-01

The purpose of this study was to measure the in vitro tensile bond strength of 3 types of adhesive resin cements to stainless steel, titanium, carbon fiber-reinforced resin, and zirconium oxide post materials. Disks of post materials were polished to 600 grit, air abraded, and ultrasonically cleaned. Zirconium oxide bonding surfaces were pretreated with hydrofluoric acid and silanated. Bis-Core, C&B Metabond, and Panavia cements were bonded to the post specimens and placed in a humidor for 24 hours. Post specimens were debonded in tension. Means and standard deviations (n = 5) were analyzed by 2-way analysis of variance. Tukey-Kramer intervals at the 0.05 significance level were calculated. Failure modes were observed. Panavia 21 provided the highest bond strengths for all types of post materials, ranging from 22 MPa (zirconium oxide) to 37 MPa (titanium). C&B Metabond bonded significantly more strongly to stainless steel (27 MPa) and titanium (22 MPa) than to zirconium oxide (7 MPa). Bis-Core results were the lowest, ranging from 16 MPa (stainless steel) to 8 MPa (zirconium oxide). In most cases, bonds to carbon fiber post materials were weaker than to stainless steel and titanium, but stronger than to zirconium oxide. In general, higher bond strengths resulted in a higher percentage of cohesive failures within the cement. Panavia 21 provided the highest bond strengths to all post materials, followed by C&B Metabond. In most cases, adhesive resins had higher bond strengths to stainless steel, titanium, and carbon fiber than to zirconium oxide.

Rock strength measurements on Archaean basement granitoids recovered from scientific drilling in the active Koyna seismogenic zone, western India

NASA Astrophysics Data System (ADS)

Goswami, Deepjyoti; Akkiraju, Vyasulu V.; Misra, Surajit; Roy, Sukanta; Singh, Santosh K.; Sinha, Amalendu; Gupta, Harsh; Bansal, B. K.; Nayak, Shailesh

2017-08-01

Reservoir triggered earthquakes have been occurring in the Koyna area, western India for the past five decades. Triaxial tests carried out on 181 core samples of Archaean granitoids underlying the Deccan Traps provide valuable constraints on rock strength properties in the Koyna seismogenic zone for the first time. The data include measurements on granite gneiss, granite, migmatitic gneiss and mylonitised granite gneiss obtained from boreholes KBH-3, KBH-4A, KBH-5 and KBH-7 located in the western and eastern margins of the seismic zone. Salient results are as follows. (i) Increase of rock strength with increasing confining pressure allow determination of the linearized failure envelopes from which the cohesive strength and angle of internal friction are calculated. (ii) Variable differential stresses at different depths are the manifestations of deformation partitioning in close association of fault zone(s) or localized fracture zones. (iii) Fractures controlled by naturally developed weak planes such as cleavage and fabric directly affect the rock strength properties, but the majority of failure planes developed during triaxial tests is not consistent with the orientations of pre-existing weak planes. The failure planes may, therefore, represent other planes of weakness induced by ongoing seismic activity. (iv) Stress-strain curves confirm that axial deformation is controlled by the varying intensity of pre-existing shear in the granitoids, viz., mylonite, granite gneiss and migmatitic gneiss. (v) Frequent occurrences of low magnitude earthquakes may be attributed to low and variable rock strength of the granitoids, which, in turn, is modified by successive seismic events.

Tensile bond strength of filled and unfilled adhesives to dentin.

PubMed

Braga, R R; Cesar, P F; Gonzaga, C C

2000-04-01

To determine the tensile bond strength of three filled and two unfilled adhesives applied to bovine dentin. Fragments of the labial dentin of bovine incisors were embedded in PVC cylinders with self-cure acrylic resin, and ground flat using 200 grit and 600 grit sandpaper. The following adhesive systems were tested (n=10): Prime & Bond NT, Prime & Bond NT dual cure, Prime & Bond 2.1, OptiBond Solo and Single Bond. A 3 mm-diameter bonding surface was delimited using a perforated adhesive tape. After etching with 37% phosphoric acid and adhesive application, a resin-based composite truncated cone (TPH, shade A3) was built. Tensile test was performed after 24 hrs storage in distilled water at 37 degrees C. Failure mode was accessed using a x10 magnification stereomicroscope. Weibull statistical analysis revealed significant differences in the characteristic strength between Single Bond and Prime & Bond NT dual cure, and between Single Bond and Prime & Bond 2.1. The Weibull parameter (m) was statistically similar among the five groups. Single Bond and Prime & Bond NT showed areas of dentin cohesive failure in most of the specimens. For OptiBond Solo, Prime & Bond NT dual cure and Prime & Bond 2.1 failure was predominantly adhesive.

Adhesion of maxillofacial silicone elastomer to a fiber-reinforced composite resin framework.

PubMed

Kantola, Rosita; Lassila, Lippo; Vallittu, Pekka

2011-01-01

Recently, fiber-reinforced composite resin (FRC) has been introduced as a framework material for maxillofacial silicone prostheses. The purpose of this research was to study the tensile bond strength between a room temperature-polymerized maxillofacial silicone elastomer and a unidirectional FRC. Three different bonding agents were compared. Specimens were loaded in tension mode according to ISO 22401 in a universal testing device with a crosshead speed of 10 mm/min until bonding failure occurred. The influence of the surface characteristics (ground vs intact) was also studied. The highest tensile bond strength was seen with Gold Platinum Primer A-330-G, followed by Sofreliner primer. One-way analysis of variance revealed that the surface treatment of the FRC and the adhesive used had a significant effect on tensile bond strength between silicone and FRC (P < .05). Grinding enhanced adhesion, especially with Gold Platinum Primer A-330-G and Sofreliner primer. The fracture type also changed to more cohesive in nature. The FRC substructure can successfully be bonded to maxillofacial silicone elastomer by using primer containing methyl ethyl ketone and dichloromethane solvent. Bonding can be improved by roughening the FRC substrate via grinding.

Slope stability and bearing capacity of landfills and simple on-site test methods.

PubMed

Yamawaki, Atsushi; Doi, Yoichi; Omine, Kiyoshi

2017-07-01

This study discusses strength characteristics (slope stability, bearing capacity, etc.) of waste landfills through on-site tests that were carried out at 29 locations in 19 sites in Japan and three other countries, and proposes simple methods to test and assess the mechanical strength of landfills on site. Also, the possibility of using a landfill site was investigated by a full-scale eccentric loading test. As a result of this, landfills containing more than about 10 cm long plastics or other fibrous materials were found to be resilient and hard to yield. An on-site full scale test proved that no differential settlement occurs. The repose angle test proposed as a simple on-site test method has been confirmed to be a good indicator for slope stability assessment. The repose angle test suggested that landfills which have high, near-saturation water content have considerably poorer slope stability. The results of our repose angle test and the impact acceleration test were related to the internal friction angle and the cohesion, respectively. In addition to this, it was found that the air pore volume ratio measured by an on-site air pore volume ratio test is likely to be related to various strength parameters.

Effect of Boron Microalloying Element on Susceptibility to Hydrogen Embrittlement in High Strength Mooring Chain Steel

NASA Astrophysics Data System (ADS)

Li, H.; Cheng, X. Y.; Shen, H. P.; Su, L. C.; Zhang, S. Y.

The susceptibility to hydrogen embrittlement in high strength mooring chain steel with different boron content (0, 0.003 %, 0.008 %) were investigated by electrochemical hydrogen charging technique and tensile test. The results revealed that appropriate boron content can effectively depress hydrogen induced embrittlement. Precharged with a low current density, this effect seemed to be unobvious. It gradually became clearly with the increasing current density. The increase of resistance to the hydrogen embrittlement for 3B and 8B after adding appropriate boron was attributed to three facts. The first was that the segregation of boron atoms along grain boundaries reduced the grain boundary segregation of phosphorus, which prohibited hydrogen concentration at the grain boundaries, depressing the possibility of the intergranular fracture due to H. The second was that the segregation of boron increased intergranular cohesion, enhanced grain boundary strength, and refined the final microstructure. The third was that the addition of boron changed the state of hydrogen traps, leading to the small amount of diffusible hydrogen. That is to say, hydrogen transferred to these defects by dislocations was accordingly decreased, which led to the low sensitive of hydrogen induced cracking.

Electrophoretic deposition of silicon substituted hydroxyapatite coatings from n-butanol-chloroform mixture.

PubMed

Xiao, Xiu Feng; Liu, Rong Fang; Tang, Xiao Lian

2008-01-01

Silicon Substituted Hydroxyapatite (Si-HA) coatings were prepared on titanium substrates by electrophoretic deposition (EPD). The stability of Si-HA suspension in n-butanol and chloroform mixture has been studied by electricity conductivity and sedimentation test. The microstructure, shear strength and bioactivity in vitro has been tested. The stability of Si-HA suspension containing n-butanol and chloroform mixture as medium is better than that of pure n-butanol as medium. The good adhesion of the particles with the substrate and good cohesion between the particles were obtained in n-butanol and chloroform mixture. Adding triethanolamine (TEA) as additive into the suspension is in favor of the formation of uniform and compact Si-HA coatings on the titanium substrates by EPD. The shear strength of the coatings can reach 20.43 MPa after sintering at 700 degrees C for 2 h, when the volume ratio of n-butanol: chloroform is 2:1 and the concentration of TEA is 15 ml/L. Titanium substrates etched in H(2)O(2)/NH(3) solution help to improve the shear strength of the coatings. After immersion in simulated body fluid for 7 days, Si-HA coatings have the ability to induce the bone-like apatite formation.

Does neighborhood social cohesion modify the relationship between neighborhood social norms and smoking behaviors in Mexico?

PubMed

Lozano, Paula; Fleischer, Nancy L; Moore, Spencer; Shigematsu, Luz Myriam Reynales; Santillán, Edna Arillo; Thrasher, James F

2016-07-01

The aim of this study was to examine the separate and combined relationships of neighborhood social norms and neighborhood social cohesion with smoking behavior in a cohort of adult Mexican smokers. Neighborhood anti-smoking norms were measured as the proportion of residents in each neighborhood who believed that society disapproves of smoking. Perceived social cohesion was measured using a 5-item cohesion scale and aggregated to the neighborhood level. Higher neighborhood anti-smoking norms were associated with less successful quitting. Neighborhood social cohesion modified the relationship between neighborhood social norms and two smoking behaviors: smoking intensity and quit attempts. Residents of neighborhoods with weaker anti-smoking norms and higher social cohesion had lower smoking intensity and more quit attempts than residents living in other areas. Social cohesion may help buffer smoking behavior in areas with weak social norms. Copyright © 2016 Elsevier Ltd. All rights reserved.

Companionship in the neighborhood context: Older adults’ living arrangements and perceptions of social cohesion

PubMed Central

Bromell, Lea; Cagney, Kathleen A.

2014-01-01

This study investigated the impact of neighborhood social cohesion on the perceived companionship of nearly 1,500 community-dwelling older adults from the Neighborhood, Organization, Aging and Health project (NOAH), a Chicago-based study of older adult well-being in the neighborhood context. We hypothesized that the relationship between neighborhood-level social cohesion and individual residents’ reports of companionship would be more pronounced among those who lived alone than those who resided with others. Controlling for age, gender, education, race, marital status, length of neighborhood residence, and self-rated health, neighborhood social cohesion predicted companionship among those who lived alone; for a one-unit increase in neighborhood social cohesion, the odds of reporting companionship increased by half. In contrast, social cohesion did not predict the companionship of those who resided with others. The results suggest that older adults who live alone particularly profit from the benefits of socially cohesive neighborhood environments. PMID:24860203

Lexical Cohesion and Specialized Knowledge in Science and Popular Science Texts.

ERIC Educational Resources Information Center

Myers, Greg

1991-01-01

Examines cohesion in the introductions to some scientific articles and compares the patterns to those from popularizations. Discusses a computational model of cohesion. Argues that readers of scientific articles must have a knowledge of lexical relations to see the implicit cohesion, whereas readers of popularizations must see the cohesive…

Cohesion energetics of carbon allotropes: Quantum Monte Carlo study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shin, Hyeondeok; Kang, Sinabro; Koo, Jahyun

2014-03-21

We have performed quantum Monte Carlo calculations to study the cohesion energetics of carbon allotropes, including sp{sup 3}-bonded diamond, sp{sup 2}-bonded graphene, sp–sp{sup 2} hybridized graphynes, and sp-bonded carbyne. The computed cohesive energies of diamond and graphene are found to be in excellent agreement with the corresponding values determined experimentally for diamond and graphite, respectively, when the zero-point energies, along with the interlayer binding in the case of graphite, are included. We have also found that the cohesive energy of graphyne decreases systematically as the ratio of sp-bonded carbon atoms increases. The cohesive energy of γ-graphyne, the most energetically stablemore » graphyne, turns out to be 6.766(6) eV/atom, which is smaller than that of graphene by 0.698(12) eV/atom. Experimental difficulty in synthesizing graphynes could be explained by their significantly smaller cohesive energies. Finally, we conclude that the cohesive energy of a newly proposed graphyne can be accurately estimated with the carbon–carbon bond energies determined from the cohesive energies of graphene and three different graphynes considered here.« less

The effect of different final irrigant activation techniques on the bond strength of an epoxy resin-based endodontic sealer: a preliminary study.

PubMed

Topçuoğlu, Hüseyin Sinan; Tuncay, Öznur; Demirbuga, Sezer; Dinçer, Asiye Nur; Arslan, Hakan

2014-06-01

The aim of this study was to evaluate whether or not different final irrigation activation techniques affect the bond strength of an epoxy resin-based endodontic sealer (AH Plus; Dentsply DeTrey, Konstanz, Germany) to the root canal walls of different root thirds. Eighty single-rooted human mandibular premolars were prepared by using the ProTaper system (Dentsply Maillefer, Ballaigues, Switzerland) to size F4, and a final irrigation regimen using 3% sodium hypochlorite and 17% EDTA was performed. The specimens were randomly divided into 4 groups (n = 20) according to the final irrigation activation technique used as follows: no activation (control), manual dynamic activation (MDA), CanalBrush (Coltene Whaledent, Altststten, Switzerland) activation, and ultrasonic activation. Five specimens from each group were prepared for scanning electron microscopic observation to assess the smear layer removal after the final irrigation procedures. All remaining roots were then obturated with gutta-percha and AH Plus sealer. A push-out test was used to measure the bond strength between the root canal dentin and AH Plus sealer. The data obtained from the push-out test were analyzed using 2-way analysis of variance and Tukey post hoc tests. The bond strength values mostly decreased in the coronoapical direction (P < .001). In the coronal and middle thirds, ultrasonic activiation showed a higher bond strength than other groups (P < .05). In the apical third, MDA displayed the highest bond strength to root dentin (P < .05). The majority of specimens exhibited cohesive failures. The bond strength of AH Plus sealer to root canal dentin may improve with ultrasonic activation in the coronal and middle thirds and MDA in the apical third. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Comparison of the Effect of two Denture Cleansers on Tensile bond Strength of a Denture Liner.

PubMed

Farzin, M; Bahrani, F; Adelpour, E

2013-09-01

One of the most clinical challenging issues in prosthodontics is debonding of soft liners from the denture base. The aim of this study was to evaluate and compare tensile bond strength between soft liner and heat-cured acrylic resin when immersed in two different types of denture cleanser and distilled water, at different period of times. In this experimental in vivo study, 238 heat-cured acrylic blocks were made. A soft liner was embedded between the acrylic blocks. Samples were divided into four groups: 17 samples were in the control group and were not soaked in any solution .The remaining samples were divided into 3 groups (Distilled water, Calgon and Fittydent). Each group was then subdivided into two subcategories, regarding the immersion time variable; 15 and 45 minutes. All samples were placed in tension force and tensile bond strength was recorded with the testing machine. One- way ANOVA and Tucky HSD post-hoc test were adopted to analyze the yielded data (α> 0.05). Specimens which were immersed in two denture cleansers (Fittydent and Calgon) and in distilled water showed significant difference (p= 0.001) in bonding strength when compared to the control group. The subjects immersed in denture cleanser solutions and distilled water did not reveal any significant difference (p= 0.90). For all groups; most of the bonding failures (72%) were cohesive type. The effect of the denture cleansers and distilled water on the bond strength was not statistically different; however, the difference was significant between the immersed groups with the non-immersed group. Moreover, type of the denture cleanser did not show any effect on the tensile strength. The tensile strength increases with time of immersion.

Effect of organic solvents compared to sandblasting on the repair bond strength of nanohybrid and nanofilled composite resins.

PubMed

Brum, Rafael Torres; Vieira, Sergio; Freire, Andrea; Mazur, Rui Fernando; De Souza, Evelise Machado; Rached, Rodrigo Nunes

2017-01-01

This study evaluated the effect of different surface treatments on the repair bond strength of nanohybrid (Empress Direct) and nanofilled (Filtek Z350 XT) composite resins. A total of 120 specimens of each material (7.5 x 4.5 x 3 mm) were prepared and polished with SiC paper. Half of the specimens were kept in water for seven days and the other half for six months; they were then divided into six groups according to the type of surface treatment: negative control (no treatment), Al2O3sandblasted, liquid acetone, acetone gel, liquid alcohol and alcohol gel. Following application of the silane coupling agent and the adhesive system, composite resin cylinders were fabricated on the specimens and light cured (20 seconds). The same composite resins were used for the repair. Additionally, ten intact specimens of each composite resin (without repair) were prepared (positive control). The specimens were then loaded to failure in the microshear mode. Three additional specimens were fabricated in each group, and the surface treatments were analyzed by atomic force microscopy, energy-dispersive X-ray spectroscopy (EDS) and scanning electron microscopy (SEM). The nanofilled composite resin showed higher cohesive strength and repair bond strength than the nanohybrid composite resin. The aging process affected the repair bond strength of the nanofilled composite resin. Al2O3sandblasting was more efficient for the nanofilled composite resin and promoted greater surface roughness in both materials. The solvents demonstrated higher efficacy for the nanohybrid composite resin. The strengths resulting from the solvents were material dependent, and Al2O3sandblasting resulted in superior repair bond strength in both materials.

The effect of denture base surface pretreatments on bond strengths of two long term resilient liners

PubMed Central

Parkhedkar, Rambhau

2011-01-01

PURPOSE Purpose of this study was to evaluate effect of two surface treatments, sandblasting and monomer treatment, on tensile bond strength between two long term resilient liners and poly (methyl methacrylate) denture base resin. MATERIALS AND METHODS Two resilient liners Super-Soft and Molloplast-B were selected.Sixty acrylic resin (Trevalon) specimens with cross sectional area of 10×10 mm were prepared and divided into two groups of 30 specimens each. Each group was surface treated (n = 10) by sandblasting (250 µ alumina particles), monomer treatment (for 180 sec) and control (no surface treatment). Resilient liners were processed between 2 poly(methyl methacrylate) surfaces, in the dimensions of 10×10×3 mm. Tensile strength was determined with Instron Universal testing machine, at a crosshead speed of 5 mm/min; and the modes of failure (adhesive, cohesive or mixed) were recorded. The data were analyzed using one-way ANOVA, followed by Tukey HSD test (α = 0.05). RESULTS Monomer pretreatment of acrylic resin produced significantly higher bond strengths when compared to sandblasting and control for both resilient liners (P < .001). Sandblasting significantly decreased the bond strength for both the liners when compared to monomer pretreatment and control (P < .001). Mean bond strength of Super-Soft lined specimens was significantly higher than Molloplast-B in various surface treatment groups (P < .05). CONCLUSION Surface pretreatment of the acrylic resin with monomer prior to resilient liner application is an effective method to increase bond strength between the base and soft liner. Sandblasting, on the contrary, is not recommended as it weakens the bond between the two. PMID:21503188

[Effects of Korean proficiency and parent-child cohesion on self-esteem and acculturation among children from multicultural families].

PubMed

Kim, Mi Ye; Lim, Ji Young; Chung, Grace H

2012-12-01

There is evidence that parent-child cohesion is a potentially influential factor in children's self-esteem and acculturation. However, no research to date has examined cohesion with parents as a potential pathway between Korean proficiency and self-esteem or acculturation among children from multicultural families. This study was done to address these limitations by examining whether and to what extent cohesion with parents mediated the effect of Korean proficiency on self-esteem and acculturation among children from multicultural families. Data were collected from a sample of 138 mothers and their children living in Seoul, Daegu, Kyungi province, and Kyungpook province. Multiple regression analysis was used to examine the relationships between the variables of interest. Mediation effects of cohesion with parents were tested by following the procedure recommended by Baron and Kenny (1986). Cohesion with parents partially mediated the relationship between Korean proficiency and self-esteem. For children's acculturation, the effect of Korean proficiency was partially mediated through father-child cohesion. Mother-child cohesion completely mediated the relationship between Korean proficiency and acculturation. These findings suggest that to help children from multicultural families experiencing difficulties with self-esteem or acculturation, it might be useful to develop programs that are aimed at strengthen cohesion with parents.

Happier together. Social cohesion and subjective well-being in Europe.

PubMed

Delhey, Jan; Dragolov, Georgi

2016-06-01

Despite mushrooming research on "social" determinants of subjective well-being (SWB), little is known as to whether social cohesion as a collective property is among the key societal conditions for human happiness. This article fills this gap in investigating the importance of living in a cohesive society for citizens' SWB. For 27 European Union countries, it combines the newly developed Bertelsmann Foundation's Cohesion Index with individual well-being data on life evaluation and psychological functioning as surveyed in the recent European Quality of Life Survey. The main results from multi-level analyses are as follows. First, Europeans are indeed happier and psychologically healthier in more cohesive societies. Second, all three core domains of cohesion increase individuals' SWB. Third, citizens in the more affluent part of Europe feel the positivity of social cohesion more consistently than those in the less affluent part. Finally, within countries, cohesion is good for the SWB of resource-rich and resource-poor groups alike. Our findings also shed new light on the ongoing debate on economic progress and quality of life: what makes citizenries of affluent societies happier is, in the first place, their capacity to create togetherness and solidarity among their members-in other words, cohesion. © 2015 International Union of Psychological Science.

Neighborhood cohesion and daily well-being: Results from a diary study

PubMed Central

Robinette, Jennifer W.; Charles, Susan T.; Mogle, Jacqueline A.; Almeida, David M.

2013-01-01

Neighborly cohesiveness has documented benefits for health. Furthermore, high perceived neighborhood cohesion offsets the adverse health effects of neighborhood socioeconomic adversity. One potential way neighborhood cohesion influences health is through daily stress processes. The current study uses participants (n = 2022, age 30–84 years) from The Midlife in the United States II and the National Study of Daily Experiences II, collected between 2004–2006, to examine this hypothesis using a within-person, daily diary design. We predicted that people who perceive high neighborhood cohesion are exposed to fewer daily stressors, such as interpersonal arguments, lower daily physical symptoms and negative affect, and higher daily positive affect. We also hypothesized that perceptions of neighborhood cohesion buffer declines in affective and physical well-being on days when daily stressors do occur. Results indicate that higher perceived neighborhood cohesion predicts fewer self-reported daily stressors, higher positive affect, lower negative affect, and fewer physical health symptoms. High perceived neighborhood cohesion also buffers the effects of daily stressors on negative affect, even after adjusting for other sources of social support. Results from the present study suggest interventions focusing on neighborhood cohesion may result in improved well-being and may minimize the adverse effect of daily stressors. PMID:24034965

Impact cratering on porous targets in the strength regime

NASA Astrophysics Data System (ADS)

Nakamura, Akiko M.

2017-12-01

Cratering on small bodies is crucial for the collision cascade and also contributes to the ejection of dust particles into interplanetary space. A crater cavity forms against the mechanical strength of the surface, gravitational acceleration, or both. The formation of moderately sized craters that are sufficiently larger than the thickness of the regolith on small bodies, in which mechanical strength plays the dominant role rather than gravitational acceleration, is in the strength regime. The formation of microcraters on blocks on the surface is also within the strength regime. On the other hand, the formation of a crater of a size comparable to the thickness of the regolith is affected by both gravitational acceleration and cohesion between regolith particles. In this short review, we compile data from the literature pertaining to impact cratering experiments on porous targets, and summarize the ratio of spall diameter to pit diameter, the depth, diameter, and volume of the crater cavity, and the ratio of depth to diameter. Among targets with various porosities studied in the laboratory to date, based on conventional scaling laws (Holsapple and Schmidt, J. Geophys. Res., 87, 1849-1870, 1982) the cratering efficiency obtained for porous sedimentary rocks (Suzuki et al., J. Geophys. Res. 117, E08012, 2012) is intermediate. A comparison with microcraters formed on a glass target with impact velocities up to 14 km s-1 indicates a different dependence of cratering efficiency and depth-to-diameter ratio on impact velocity.

Effect of zirconia surface treatment using nitric acid-hydrofluoric acid on the shear bond strengths of resin cements

PubMed Central

Kim, Sun Jai; Shim, June Sung

2017-01-01

PURPOSE The aim of this study was to compare the surface roughness of zirconia when using Zircos E etching system (ZSAT), applying a nitric acid-hydrofluoric acid compound as a pretreatment agent, and also to compare the shear bonding strength according to different resin cements. MATERIALS AND METHODS ZSAT, air abrasion, and tribochemical silicacoating were applied on prepared 120 zirconia specimens (10 mm in diameter, 7 mm in height) using CAD/CAM. Each 12 specimens with 4 different resin cements (Panavia F 2.0, Rely X Unicem, Superbond C&B, and Hot bond) were applied to test interfacial bond strength. The statistical analysis was performed using SAS 9.1 (SAS Institute Inc., Cary, NC, USA). The results are as follows: after application of the ZSAT on the zirconia specimens, surface roughness value after 2-hour etching was higher than those after 1- and 3-hour etching on SEM images. RESULTS For Superbond C&B and Rely X Unicem, the specimens treated with ZSAT showed higher shear bond strength values than those treated with air abrasion and tribochemical silicacoating system. Regarding the failure mode of interface over cement and zirconia surface, Rely X Unicem and Hot bond showed cohesive failures and Panavia F 2.0 and Superbond C&B showed mixed failures. CONCLUSION Zircos E etching system in zirconia restoration could increase its shear bond strength. However, its long term success rate and clinical application should be further evaluated. PMID:28435615

Experimental Study on Artificial Cemented Sand Prepared with Ordinary Portland Cement with Different Contents.

PubMed

Li, Dongliang; Liu, Xinrong; Liu, Xianshan

2015-07-02

Artificial cemented sand test samples were prepared by using ordinary Portland cement (OPC) as the cementing agent. Through uniaxial compression tests and consolidated drained triaxial compression tests, the stress-strain curves of the artificial cemented sand with different cementing agent contents (0.01, 0.03, 0.05 and 0.08) under various confining pressures (0.00 MPa, 0.25 MPa, 0.50 MPa and 1.00 MPa) were obtained. Based on the test results, the effect of the cementing agent content ( C v ) on the physical and mechanical properties of the artificial cemented sand were analyzed and the Mohr-Coulomb strength theory was modified by using C v . The research reveals that when C v is high (e.g., C v = 0.03, 0.05 or 0.08), the stress-strain curves of the samples indicate a strain softening behavior; under the same confining pressure, as C v increases, both the peak strength and residual strength of the samples show a significant increase. When C v is low (e.g., C v = 0.01), the stress-strain curves of the samples indicate strain hardening behavior. From the test data, a function of C v (the cementing agent content) with c ' (the cohesion force of the sample) and Δϕ' (the increment of the angle of shearing resistance) is obtained. Furthermore, through modification of the Mohr-Coulomb strength theory, the effect of cementing agent content on the strength of the cemented sand is demonstrated.

Influence of cement thickness on resin-zirconia microtensile bond strength

PubMed Central

Lee, Tae-Hoon; Ahn, Jin-Soo; Shim, June-Sung; Han, Chong-Hyun

2011-01-01

PURPOSE The aim of this study was to evaluate the influence of resin cement thickness on the microtensile bond strength between zirconium-oxide ceramic and resin cement. MATERIALS AND METHODS Thirty-two freshly extracted molars were transversely sectioned at the deep dentin level and bonded to air-abraded zirconium oxide ceramic disks. The specimens were divided into 8 groups based on the experimental conditions (cement type: Rely X UniCem or Panavia F 2.0, cement thickness: 40 or 160 µm, storage: thermocycled or not). They were cut into microbeams and stored in 37℃ distilled water for 24 h. Microbeams of non-thermocycled specimens were submitted to a microtensile test, whereas those of thermocycled groups were thermally cycled for 18,000 times immediately before the microtensile test. Three-way ANOVA and Sheffe's post hoc tests were used for statistical analysis (α=95%). RESULTS All failures occurred at the resin-zirconia interface. Thermocycled groups showed lower microtensile bond strength than non-thermocycled groups (P<.001). Differences in cement thickness did not influence the resin-zirconia microtensile bond strength given the same resin cement or storage conditions (P>.05). The number of adhesive failures increased after thermocycling in all experimental conditions. No cohesive failure was observed in any experimental group. CONCLUSION When resin cements of adhesive monomers are applied over air-abraded zirconia restorations, the degree of fit does not influence the resin-zirconia microtensile bond strength. PMID:22053241

Context matters: Community social cohesion and health behaviors in two South African areas.

PubMed

Lippman, Sheri A; Leslie, Hannah H; Neilands, Torsten B; Twine, Rhian; Grignon, Jessica S; MacPhail, Catherine; Morris, Jessica; Rebombo, Dumisani; Sesane, Malebo; El Ayadi, Alison M; Pettifor, Audrey; Kahn, Kathleen

2018-03-01

Understanding how social contexts shape HIV risk will facilitate development of effective prevention responses. Social cohesion, the trust and connectedness experienced in communities, has been associated with improved sexual health and HIV-related outcomes, but little research has been conducted in high prevalence settings. We conducted population-based surveys with adults 18-49 in high HIV prevalence districts in Mpumalanga (n = 2057) and North West Province (n = 1044), South Africa. Community social cohesion scores were calculated among the 70 clusters. We used multilevel logistic regression stratified by gender to assess individual- and group-level associations between social cohesion and HIV-related behaviors: recent HIV testing, heavy alcohol use, and concurrent sexual partnerships. Group-level cohesion was protective in Mpumalanga, where perceived social cohesion was higher. For each unit increase in group cohesion, the odds of heavy drinking among men were reduced by 40% (95%CI 0.25, 0.65); the odds of women reporting concurrent sexual partnerships were reduced by 45% (95%CI 0.19, 1.04; p = 0.06); and the odds of reporting recent HIV testing were 1.6 and 1.9 times higher in men and women, respectively. We identified potential health benefits of cohesion across three HIV-related health behaviors in one region with higher overall evidence of group cohesion. There may be a minimum level of cohesion required to yield positive health effects. Copyright © 2018 Elsevier Ltd. All rights reserved.

Coach-initiated motivational climate and cohesion in youth sport.

PubMed

Eys, Mark A; Jewitt, Eryn; Evans, M Blair; Wolf, Svenja; Bruner, Mark W; Loughead, Todd M

2013-09-01

The general purpose of the present study was to examine the link between cohesion and motivational climate in youth sport. The first specific objective was to determine if relationships demonstrated in previous research with adult basketball and handball participants would be replicated in a younger sample and with a more heterogeneous set of sports. The second specific objective was to examine whether sources of athlete enjoyment moderate the relationships between motivational climate and cohesion. Athletes (N = 997; 532 girls and 465 boys; Mage = 15.26 +/- 1.20 years) completed measures pertaining to coach-initiated motivational climate, cohesion, and sources of enjoyment. Bivariate and canonical correlations revealed positive correlations between perceptions of a task-involving motivational climate and both task and social cohesion, while ego-involving motivational climate was negatively related. Cluster analyses suggested that individuals perceiving a low task-involving climate and high ego-involving climate perceived their teams as less cohesive. Finally, the degree to which participants derived enjoyment through other-referenced competency served as a moderator in the motivational climate-task cohesion relationship. Specifically, the relationship between task cohesion and motivational climate was more pronounced for those individuals who were less likely to derive enjoyment through other-referenced competency. Youth athletes' perceptions of coach-initiated motivational climate are related to cohesion. This relationship is, however, moderated by the degree to which athletes derive enjoyment through other-referenced competency. Motivational climate is an important variable to consider within team-building protocols intent on developing cohesion.

Relationship between the cohesion of guest particles on the flow behaviour of interactive mixtures.

PubMed

Mangal, Sharad; Gengenbach, Thomas; Millington-Smith, Doug; Armstrong, Brian; Morton, David A V; Larson, Ian

2016-05-01

In this study, we aimed to investigate the effects cohesion of small surface-engineered guest binder particles on the flow behaviour of interactive mixtures. Polyvinylpyrrolidone (PVP) - a model pharmaceutical binder - was spray-dried with varying l-leucine feed concentrations to create small surface-engineered binder particles with varying cohesion. These spray-dried formulations were characterised by their particle size distribution, morphology and cohesion. Interactive mixtures were produced by blending these spray-dried formulations with paracetamol. The resultant blends were visualised under scanning electron microscope to confirm formation of interactive mixtures. Surface coverage of paracetamol by guest particles as well as the flow behaviour of these mixtures were examined. The flow performance of interactive mixtures was evaluated using measurements of conditioned bulk density, basic flowability energy, aeration energy and compressibility. With higher feed l-leucine concentrations, the surface roughness of small binder particles increased, while their cohesion decreased. Visual inspection of the SEM images of the blends indicated that the guest particles adhered to the surface of paracetamol resulting in effective formation of interactive mixtures. These images also showed that the low-cohesion guest particles were better de-agglomerated that consequently formed a more homogeneous interactive mixture with paracetamol compared with high-cohesion formulations. The flow performance of interactive mixtures changed as a function of the cohesion of the guest particles. Interactive mixtures with low-cohesion guest binder particles showed notably improved bulk flow performance compared with those containing high-cohesion guest binder particles. Thus, our study suggests that the cohesion of guest particles dictates the flow performance of interactive mixtures. Crown Copyright © 2016. Published by Elsevier B.V. All rights reserved.

Bedform development in mixed sand-mud: The contrasting role of cohesive forces in flow and bed

NASA Astrophysics Data System (ADS)

Baas, Jaco H.; Davies, Alan G.; Malarkey, Jonathan

2013-01-01

The majority of subaqueous sediment on Earth consists of mixtures of cohesive clay and cohesionless sand and silt, but the role of cohesion on the development and stability of sedimentary bedforms is poorly understood. The results of new laboratory flume experiments on bedform development in cohesive, mixed sand-mud beds are compared with the results of previous experiments in which cohesive forces in high concentration clay flows dominated bedform development. Even though both series of mixed sand-mud experiments were conducted at similar flow velocities, the textural and structural properties of the bedforms were sufficiently different to permit the designation of key criteria for identifying bedform generation under cohesive flows against bedform generation on cohesive substrates. These criteria are essential for improving bedform size predictions in sediment transport modelling in modern sedimentary environments and for the reconstruction of depositional processes in the geological record. The current ripples developing on the cohesive, mixed sand-mud beds, with bed mud fractions of up to 18%, were significantly smaller than equivalent bedforms in noncohesive sand. Moreover, the bedform height showed a stronger inversely proportional relationship with initial bed mud fraction than the bedform wavelength. This is in contrast with the bedforms developing under the cohesive clay flows, which tend to increase in size with increasing suspended clay concentration until the flow turbulence is fully suppressed. Selective removal of clay from the mixed beds, i.e., clay winnowing, was found to be an important process, with 82-100% clay entrained into suspension after 2 h of bedform development. This winnowing process led to the development of a sand-rich armouring layer. This armouring layer is inferred to have protected the underlying mixed sand-mud from prolonged erosion, and in conjunction with strong cohesive forces in the bed may have caused the smaller size of the bedforms. Winnowing was less efficient for the bedforms developing under the cohesive clay flows, where bedforms consisting of muddy sand were more characteristic. The winnowed sand was also found to heal irregularly scoured topography, thus reestablishing classic quasitriangular bedform shapes. In cohesive flows, the bedforms had more variable shapes, and the healing process was confined to lower transitional plug flows in which strong turbulence is only present close to the sediment bed. Furthermore, the bedforms on the cohesive beds tended to form angle-of-repose cross lamination, whereas low angle cross lamination was more common in bedforms under cohesive flows. In general terms, erosional bedforms prevail when cohesive forces in the bed dominate bedform dynamics, whereas depositional bedforms prevail when cohesive forces in the flow dominate bedform dynamics. Empirical relationships between the proportion of cohesive mud in the mixed sand-mud bed and the development rate and size of the bedforms are defined for future use in field and laboratory studies.

Social Cohesion as a Real-Life Phenomenon: Assessing the Explanatory Power of the Universalist and Particularist Perspectives

ERIC Educational Resources Information Center

Janmaat, Jan Germen

2011-01-01

Unlike most studies on social cohesion, this study explores the concept as a real-life macro-level phenomenon. It assesses to what extent the conceptions of social cohesion suggested by several macro-level approaches represent coherent empirically observable forms of social cohesion. Additionally it discusses two perspectives on social…

Microstructural, textural, and sensory properties of whole-wheat noodle modified by enzymes and emulsifiers.

PubMed

Niu, Meng; Hou, Gary G; Kindelspire, Julie; Krishnan, Padmanaban; Zhao, Siming

2017-05-15

With the utilization of enzymes including endoxylanase, glucose oxidase (GOX) and transglutaminase (TG), and emulsifiers comprising sodium stearoyl lactate (SSL) and soy lecithin, the microstructural, textural, and sensory properties of whole-wheat noodle (WWN) were modified. The development time and stability of whole-wheat dough (WWD) were enhanced by TG due to the formation of a more compact gluten network, and by SSL resulting from the enhanced gluten strength. Microstructure graphs by scanning electron microscopy (SEM) verified that TG and SSL promoted the connectivity of gluten network and the coverage of starch granules in WWN. TG increased the hardness and elasticity of cooked WWN, while two emulsifiers increased the noodle cohesiveness. Additionally, TG and SSL improved the sensory properties of noodle such as bite, springiness, and mouth-feel. The results suggest that TG and SSL are effective ingredients in enhancing the gluten strength of WWD and improving the qualities of WWN. Copyright © 2016 Elsevier Ltd. All rights reserved.

The strength of a loosely defined movement: eugenics and medicine in imperial Russia.

PubMed

Krementsov, Nikolai

2015-01-01

This essay examines the 'infiltration' of eugenics into Russian medical discourse during the formation of the eugenics movement in western Europe and North America in 1900-17. It describes the efforts of two Russian physicians, the bacteriologist and hygienist Nikolai Gamaleia (1859-1949) and the psychiatrist Tikhon Iudin (1879-1949), to introduce eugenics to the Russian medical community, analysing in detail what attracted these representatives of two different medical specialties to eugenic ideas, ideals, and policies advocated by their western colleagues. On the basis of a close examination of the similarities and differences in Gamaleia's and Iudin's attitudes to eugenics, the essay argues that lack of cohesiveness gave the early eugenics movement a unique strength. The loose mix of widely varying ideas, ideals, methods, policies, activities and proposals covered by the umbrella of eugenics offered to a variety of educated professionals in Russia and elsewhere the possibility of choosing, adopting and adapting particular elements to their own national, professional, institutional and disciplinary contexts, interests and agendas.

Use of Nanoparticles for Enhancing the Interlaminar Properties of Fiber-Reinforced Composites and Adhesively Bonded Joints—A Review

PubMed Central

De Cicco, Davide; Asaee, Zohreh; Taheri, Farid

2017-01-01

This review paper aims at reporting some of the notable works carried out concerning the use of nanoparticles (NPs) as a means of improving the resistance of fiber-reinforced polymer composite materials (FRPs) and adhesively bonded joints (ABJs) to delamination initiation and propagation. Applications of various nanoparticles, such as carbon-based, ceramic-based and mineral-based are discussed. The main properties that have been considered for improving the delamination and fatigue resistance of FRPs are the interlaminar shear strength, fracture toughness, and fracture energy. On the other hand, cohesive and interfacial strengths have been the focused parameters in the works that considered enhancement of ABJs. The reported results indicate that inclusion of NPs in polymeric matrices leads to improvement of various material properties, even though some discrepancies in the results have been noted. Notwithstanding, additional research is required to address some of the issues that have not yet been tackled, some of which will be identified throughout this review article. PMID:29104278

Geomechanical Behaviors of Laboratory-Formed Non-Cementing Hydrate-Bearing Sediments

NASA Astrophysics Data System (ADS)

Seol, Y.

2015-12-01

Natural hydrate-bearing sediments (HBS) have been known to exist with non-cementing pore habits, i.e., pore-filling, load-bearing, or patchy type. However, few laboratory studies have been conducted to characterize geomechanical behaviors of non-cementing CH4-HBS, which are of great importance in engineering the process of drilling and gas production in natural hydrate reservoir. In this study, we conducted multi-stage drained triaxial tests on laboratory synthesized CH4-HBS samples, which were formed in sand-clay mixtures (5%wt kaolinite) to have non-cementing habits. Three different effective confining stresses, σ3' = 0.69, 1.38, and 2.76 MPa, were applied on the HBS with the hydrate saturation, Sh, in the range of 0 to ~ 40%. The result confirms that the strength and stiffness of HBS increases with effective confining stress and hydrate saturation. It is also demonstrated that when compared to the cementing HBS, the non-cementing HBS has lower strength and cohesion, owing to less inter-particle adhesion effects from non-cementing hydrate.

Symmetry and novelty in the electronic and geometric structure of nanoalloys:. the case of Ag27Cu7

NASA Astrophysics Data System (ADS)

Ortigoza, M. Alcántara; Rahman, T. S.

2008-04-01

Nanoparticles of bimetallic alloys have been shown to possess composition dependent characteristics which distinguish themselves from the corresponding bulk alloys. Taking the 34-atom nanoalloy of Ag and Cu (Ag27Cu7), we show using first principles electronic structure calculations that this core-shell alloy indeed has perfect D5h symmetry and consists of only 6 non-equivalent (2 Cu and 4 Ag) atoms. Analysis of the interatomic bond lengths and detailed electronic structure further reveal that the Cu atoms play a major role in controlling the characteristics of the nanoalloy. The higher cohesive energy, together with shorter bond length for Cu, compared to Ag, conspire to produce a hierarchy in the relative strengths of the Ag - Cu, Ag - Ag, and Cu - Cu bonds and corresponding interatomic bond lengths, point to the uniqueness in the characteristics of this nanoalloy. Charge density plots of Ag27Cu7 provide further insights into the relative strengths of the various interatomic bonds.

Family cohesion and pride, drinking and alcohol use disorder in Puerto Rico.

PubMed

Caetano, Raul; Vaeth, Patrice A C; Canino, Glorisa

2017-01-01

The extended multigenerational family is a core value of Hispanic culture. Family cohesion/pride can have protective effects on drinking- and drug-use-related behavior among Hispanics. To examine the association between family cohesion/pride, drinking, binge drinking, and DSM-5 alcohol use disorder (AUD) in Puerto Rico. Data are from a household random sample of 1510 individuals 18-64 years of age in San Juan, Puerto Rico. Bivariate analyses showed that family cohesion/pride was not associated with the average number of drinks consumed per week but was associated with binge drinking among men. Family cohesion/pride was also associated with DSM-5 AUD. Results of the multivariate analyses were consistent with these bivariate results for DSM-5 AUD. Respondents with low (OR = 2.2, 95CL = 1.21-3.98; p < .01) and medium (OR = 1.88; 95CL = 1.12-3.14; p < .01) family cohesion/pride were more likely than those with high family cohesion/pride to have a positive diagnosis of DSM-5 AUD. More liberal drinking norms and positive attitudes toward drinking were also strong predictors of the average number of drinks consumed per week. More liberal drinking norms also predicted binge drinking, and DSM-5 AUD. Higher family cohesion/pride may have a protective effect against DSM-5 AUD. This may have practical implications for clinical and prevention programs. As long as high cohesion is not enabling drinking, these programs can enhance and support family cohesion/pride to help clients in treatment and recovery and prevent drinking problems.

The influence of crystal habit on the prediction of dry powder inhalation formulation performance using the cohesive-adhesive force balance approach.

PubMed

Hooton, Jennifer C; Jones, Matthew D; Harris, Haggis; Shur, Jagdeep; Price, Robert

2008-09-01

The aim of this investigation was to study the influence of crystalline habit of active pharmaceutical ingredients on the cohesive-adhesive force balance within model dry powder inhaler (DPI) formulations and the corresponding affect on DPI formulation performance. The cohesive-adhesive balance (CAB) approach to colloid probe atomic force microscopy (AFM) was employed to determine the cohesive and adhesive interactions of micronized budesonide particles against the {102} and {002} faces of budesonide single crystals and crystalline substrates of different sugars (cyclodextrin, lactose, trehalose, raffinose, and xylitol), respectively. These data were used to measure the relative level of cohesion and adhesion via CAB and the possible influence on in vitro performance of a carrier-based DPI formulation. Varying the crystal habit of the drug had a significant effect on the cohesive measurement of micronized budesonide probes, with the cohesive values on the {102} faces being approximately twice that on the {002} crystal faces. However, although different CAB values were measured with the sugars with respect to the crystal faces chosen for the cohesive-based measurement, the overall influence on the rank order of the CAB values was not directly influenced. For these data sets, the CAB gradient indicated that a decrease in the dominance of the adhesive forces led to a concomitant increase in fine particle delivery, reaching a plateau as the cohesive forces became dominant. The study suggested that crystal habit of the primary drug crystals influences the cohesive interactions and the resulting force balance measurements of colloid probe CAB analysis.

Family Cohesion and Pride: Drinking and Alcohol Use Disorders in Puerto Rico

PubMed Central

Caetano, Raul; Vaeth, Patrice A. C.; Canino, Glorisa

2017-01-01

Background The extended multigenerational family is a core value of Hispanic culture. Family cohesion/pride can have protective effects on drinking and drug use related behavior among Hispanics. Objectives To examine the association between family cohesion/pride, drinking, binge drinking, and DSM-5 alcohol use disorder in Puerto Rico. Methods Data are from a household random sample of 1510 individuals 18-64 years of age of San Juan, Puerto Rico. Results Bivariate analyses showed that family cohesion/pride was not associated with the average number of drinks consumed per week, but was associated with binge drinking among men. Family cohesion/pride was also associated with DSM-5 alcohol use disorder. Results of the multivariate analyses were consistent with these bivariate results for DSM-5 AUD. Respondents with low (OR=2.2, 95CL=1.21-3.98; p<.01) and medium (OR=1.88; 95CL=1.12-3.14; p<.01) family cohesion/pride were more likely than those with high family cohesion/pride to have a positive diagnosis of DSM-5 alcohol use disorder. More liberal drinking norms and positive attitudes towards drinking were also strong predictors of the average number of drinks consumed per week. More liberal drinking norms also predicted binge drinking, and DSM-5 AUD. Conclusions Higher family cohesion/pride may have a protective effect against DSM-5 alcohol use disorder. This may have practical implications for clinical and prevention programs. As long as high cohesion is not enabling drinking, these programs can enhance and support family cohesion/pride to help clients in treatment and recovery and prevent drinking problems. PMID:27808561

Effect of various filler types on the properties of porous asphalt mixture

NASA Astrophysics Data System (ADS)

Shukry, Nurul Athma Mohd; Hassan, Norhidayah Abdul; Ezree Abdullah, Mohd; Rosli Hainin, Mohd; Yusoff, Nur Izzi Md; Putra Jaya, Ramadhansyah; Mohamed, Azman

2018-04-01

The open structure of porous asphalt exposes a large surface area to the effects of air and water, which accelerates the oxidation rate and affects the coating properties of the binder. These factors may influence the adhesive strength of the binder-aggregate and lead to cohesive failure within the binder film, contributing to aggregate stripping and moisture damage. The addition of fillers in asphalt mixtures has been identified to stiffen the asphalt binder and improve mixture strength. This study investigates the effect of various filler types (hydrated lime, cement, and diatomite) on the properties of porous asphalt. Compacted samples of porous asphalt were prepared using Superpave gyratory compactor at the target air void content of 21%. Each sample was incorporated with 2% of filler and polymer-modified binder of PG76. The morphology and chemical composition of fillers were investigated with a field emission scanning electron microscope (FESEM) and energy dispersive X-ray (EDX) analysis. The properties of porous asphalt were evaluated in terms of permeability, abrasion loss, resilient modulus, and indirect tensile strength. All mixtures were found to show high permeability rates. Mixtures with hydrated lime exhibited lower abrasion loss compared to mixtures with cement and diatomite. The use of diatomite increases the resistance of the mixtures to rutting and moisture damage compared to other fillers as shown by the enhanced resilient modulus and indirect tensile strength.

An in vitro investigation of pre-treatment effects before fissure sealing.

PubMed

Bagheri, Mahshid; Pilecki, Peter; Sauro, Salvatore; Sherriff, Martyn; Watson, Timothy F; Hosey, Marie Therese

2017-11-01

Fissure sealants prevent occlusal caries in permanent molars. Enamel preparation methods are used before fissure sealing. To investigate effects of bioglass air-abrasion pre-treatment with and without an adhesive, on fissure enamel of permanent teeth, with respect to etchability, microleakage and microtensile bond strength. Half of the occlusal surfaces of 50 extracted premolars underwent bioglass air-abrasion. Dye was applied to the entire occlusal surface. Photographs were taken to score etched surface by dye uptake. Adhesive was applied to 25 of the bioglass-treated areas and all teeth were fissure sealed, sectioned, and evaluated using confocal microscopy. Buccal and lingual surfaces of a further eight premolars were acid-etched and randomly received: air-abrasion, adhesive, both, or none before sealant application for microtensile bond strength measurement in half of the samples immediately and half following 6 months of water immersion. Linear mixed models and multinomial logistic regression were used (P = 0.05). Bioglass air-abrasion significantly improved enamel etchability and reduced microleakage. The addition of an adhesive made no difference to either microleakage or microtensile bond strength. The combination of bioglass abrasion and adhesive led to more cohesive, rather than adhesive, failure. Bioglass air-abrasion improved enamel etchability and reduced microleakage irrespective of the adhesive use but neither pre-treatment affected the microtensile bond strength. © 2017 BSPD, IAPD and John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

The effect of remin pro and MI paste plus on bleached enamel surface roughness.

PubMed

Ahmad Akhoundi, Mohammad Sadegh; Aghajani, Farzaneh; Chalipa, Javad; Sadrhaghighi, Amir Hooman

2014-03-01

Increased number of adult patients requesting orthodontic treatment result in bonding bracket to ceramic restorations more than before. The aim of this study was to evaluate and compare the shear bond strength of orthodontic brackets bonded to two types of ceramic bases with conventional orthodontic bonding resin and a new nano-filled composite resin. Twenty four feldespathic porcelain and 24 lithium disilicate ceramic disks were fabricated. All of the samples were conditioned by sandblasting, hydrofluoric acid and silane. Maxillary incisor metal brackets were bonded to half of the disks in each group by conventional orthodontic bonding resin and the other half bonded with a nano-filled composite. The samples then were thermocycled for 2000 cycle between 5-55° C. Shear bond strength was measured and the mode of failure was examined. Randomly selected samples were also evaluated by SEM. The lowest bond strength value was found infeldespathic ceramic bonded by nano-filled composite (p<0.05). There was not any statistically significant difference between other groups regarding bond strength. The mode of failure in the all groups except group 1 was cohesive and porcelain damages were detected. Since less damages to feldspathic porcelain was observed when the nano-filled composite was used to bond brackets, the use of nano-filled composite resins can be suggested for bonding brackets to feldspathic porcelain restorations.

The Effect of Remin Pro and MI Paste Plus on Bleached Enamel Surface Roughness

PubMed Central

Ahmad Akhoundi, Mohammad Sadegh; Aghajani, Farzaneh; Chalipa, Javad; Sadrhaghighi, Amir Hooman

2014-01-01

Objective Increased number of adult patients requesting orthodontic treatment result in bonding bracket to ceramic restorations more than before. The aim of this study was to evaluate and compare the shear bond strength of orthodontic brackets bonded to two types of ceramic bases with conventional orthodontic bonding resin and a new nano-filled composite resin. Materials and Methods: Twenty four feldespathic porcelain and 24 lithium disilicate ceramic disks were fabricated. All of the samples were conditioned by sandblasting, hydrofluoric acid and silane. Maxillary incisor metal brackets were bonded to half of the disks in each group by conventional orthodontic bonding resin and the other half bonded with a nano-filled composite. The samples then were thermocycled for 2000 cycle between 5–55° C. Shear bond strength was measured and the mode of failure was examined. Randomly selected samples were also evaluated by SEM. Results: The lowest bond strength value was found infeldespathic ceramic bonded by nano-filled composite (p<0.05). There was not any statistically significant difference between other groups regarding bond strength. The mode of failure in the all groups except group 1 was cohesive and porcelain damages were detected. Conclusion: Since less damages to feldspathic porcelain was observed when the nano-filled composite was used to bond brackets, the use of nano-filled composite resins can be suggested for bonding brackets to feldspathic porcelain restorations. PMID:24910698

Neighborhood Social Cohesion as a Mediator of Neighborhood Conditions on Mothers' Engagement in Physical Activity: Results From the Geographic Research on Wellbeing Study.

PubMed

Yuma-Guerrero, Paula J; Cubbin, Catherine; von Sternberg, Kirk

2017-12-01

The purpose of this study was to determine if social cohesion mediates the effects of neighborhood and household-level socioeconomic status (SES), perceptions of neighborhood safety, and access to parks on mothers' engagement in physical activity (PA). Secondary analyses were conducted on cross-sectional data from The Geographic Research on Wellbeing (GROW) study. GROW includes survey data from a diverse sample of 2,750 California mothers. Structural equation modeling was used to test a conceptual multilevel mediation model, proposing social cohesion as a mediator of known predictors of PA. Social cohesion fully mediated the pathway from perceived neighborhood safety to mothers' PA. Social cohesion also mediated the significant relationship between neighborhood SES and PA; however, this mediation finding was not practically significant when considered in the context of the full model. Household SES was significantly positively related to both social cohesion and PA. Park access contributed significantly to social cohesion but not directly to PA Social cohesion did not significantly mediate relationships between park access or household SES and PA. There is a need for public health interventions to improve engagement in PA among individuals and neighborhoods with lower levels of socioeconomic resources. Interventions that create social cohesion within neighborhoods may have positive effects on mothers' PA, particularly in neighborhoods perceived as unsafe.

The Effect of Deposition Conditions on Adhesion Strength of Ti and Ti6Al4V Cold Spray Splats

NASA Astrophysics Data System (ADS)

Goldbaum, Dina; Shockley, J. Michael; Chromik, Richard R.; Rezaeian, Ahmad; Yue, Stephen; Legoux, Jean-Gabriel; Irissou, Eric

2012-03-01

Cold spray is a complex process where many parameters have to be considered in order to achieve optimized material deposition and properties. In the cold spray process, deposition velocity influences the degree of material deformation and material adhesion. While most materials can be easily deposited at relatively low deposition velocity (<700 m/s), this is not the case for high yield strength materials like Ti and its alloys. In the present study, we evaluate the effects of deposition velocity, powder size, particle position in the gas jet, gas temperature, and substrate temperature on the adhesion strength of cold spayed Ti and Ti6Al4V splats. A micromechanical test technique was used to shear individual splats of Ti or Ti6Al4V and measure their adhesion strength. The splats were deposited onto Ti or Ti6Al4V substrates over a range of deposition conditions with either nitrogen or helium as the propelling gas. The splat adhesion testing coupled with microstructural characterization was used to define the strength, the type and the continuity of the bonded interface between splat and substrate material. The results demonstrated that optimization of spray conditions makes it possible to obtain splats with continuous bonding along the splat/substrate interface and measured adhesion strengths approaching the shear strength of bulk material. The parameters shown to improve the splat adhesion included the increase of the splat deposition velocity well above the critical deposition velocity of the tested material, increase in the temperature of both powder and the substrate material, decrease in the powder size, and optimization of the flow dynamics for the cold spray gun nozzle. Through comparisons to the literature, the adhesion strength of Ti splats measured with the splat adhesion technique correlated well with the cohesion strength of Ti coatings deposited under similar conditions and measured with tubular coating tensile (TCT) test.

Contributions of Self-Explanation to Comprehension of High- and Low-Cohesion Texts

ERIC Educational Resources Information Center

Ozuru, Yasuhiro; Briner, Stephen; Best, Rachel; McNamara, Danielle S.

2010-01-01

This study examined how the contribution of self-explanation to science text comprehension is affected by the cohesion of a text at a local level. Psychology undergraduates read and self-explained a science text with either low or high local cohesion. Local cohesion was manipulated by the presence or absence of connectives and referential words or…

Revealing the Hidden Relationship by Sparse Modules in Complex Networks with a Large-Scale Analysis

PubMed Central

Jiao, Qing-Ju; Huang, Yan; Liu, Wei; Wang, Xiao-Fan; Chen, Xiao-Shuang; Shen, Hong-Bin

2013-01-01

One of the remarkable features of networks is module that can provide useful insights into not only network organizations but also functional behaviors between their components. Comprehensive efforts have been devoted to investigating cohesive modules in the past decade. However, it is still not clear whether there are important structural characteristics of the nodes that do not belong to any cohesive module. In order to answer this question, we performed a large-scale analysis on 25 complex networks with different types and scales using our recently developed BTS (bintree seeking) algorithm, which is able to detect both cohesive and sparse modules in the network. Our results reveal that the sparse modules composed by the cohesively isolated nodes widely co-exist with the cohesive modules. Detailed analysis shows that both types of modules provide better characterization for the division of a network into functional units than merely cohesive modules, because the sparse modules possibly re-organize the nodes in the so-called cohesive modules, which lack obvious modular significance, into meaningful groups. Compared with cohesive modules, the sizes of sparse ones are generally smaller. Sparse modules are also found to have preferences in social and biological networks than others. PMID:23762457

[Effects of family cohesion and adaptability on behavioral problems in preschool children].

PubMed

Wang, Yan-Ni; Xue, Hong-Li; Chen, Qian

2016-05-01

To investigate the effects of family cohesion and adaptability on behavioral problems in preschool children. The stratified cluster multistage sampling method was used to perform a questionnaire survey in the parents of 1 284 children aged 3-6 years in the urban area of Lanzhou, China. The general status questionnaire, Conners Child Behavior Checklist (Parent Symptom Question), and Family Adaptability and Cohesion Scale, Second edition, Chinese version (FACESII-CV) were used to investigate behavioral problems and family cohesion and adaptability. The overall detection rate of behavioral problems in preschool children was 17.13%. The children with different types of family cohesion had different detection rates of behavioral problems, and those with free-type family cohesion showed the highest detection rate of behavioral problems (40.2%). The children with different types of family adaptability also had different detection rates of behavioral problems, and those with stiffness type showed the highest detection rate of behavioral problems (25.1%). The behavioral problems in preschool children were negatively correlated with family cohesion and adaptability. During the growth of preschool children, family cohesion and adaptability have certain effects on the mental development of preschool children.

Authentic leadership, group cohesion and group identification in security and emergency teams.

PubMed

García-Guiu López, Carlos; Molero Alonso, Fernando; Moya Morales, Miguel; Moriano León, Juan Antonio

2015-01-01

Authentic leadership (AL) is a kind of leadership that inspires and promotes positive psychological capacities, underlining the moral and ethical component of behavior. The proposed investigation studies the relations among AL, cohesion, and group identification in security and emergency teams. A cross-sectional research design was conducted in which participated 221 members from 26 fire departments and operative teams from the local police of three Spanish provinces. The following questionnaires were administered: Authentic Leadership (ALQ), Group Cohesion (GEQ), and Mael and Ashford's Group Identification Questionnaire. A direct and positive relation was found between AL, cohesion, and group identification. An indirect relation was also found between AL and group cohesion through group identification, indicating the existence of partial mediation. The utility of the proposed model based on AL is considered; this model can be employed by those in charge of the fire departments and operative groups in organizations to improve workteams' cohesion. Both AL and group identification help to explain group cohesion in organizations committed to security and emergencies.

Negative emotional reactivity moderates the relations between family cohesion and internalizing and externalizing symptoms in adolescence✩

PubMed Central

Rabinowitz, Jill A.; Osigwe, Ijeoma; Drabick, Deborah A.G.; Reynolds, Maureen D.

2016-01-01

Lower family cohesion is associated with adolescent internalizing and externalizing problems. However, there are likely individual differences in youth's responses to family processes. For example, adolescents higher in negative emotional reactivity, who often exhibit elevated physiological responsivity to context, may be differentially affected by family cohesion. We explored whether youth's negative emotional reactivity moderated the relation between family cohesion and youth's symptoms and tested whether findings were consistent with the diathesis-stress model or differential susceptibility hypothesis. Participants were 651 adolescents (M = 12.99 ± .95 years old; 72% male) assessed at two time points (Time 1, ages 12–14; Time 2, age 16) in Pittsburgh, PA. At Time 1, mothers reported on family cohesion and youth reported on their negative emotional reactivity. At Time 2, youth reported on their symptoms. Among youth higher in negative emotional reactivity, lower family cohesion predicted higher symptoms than higher family cohesion, consistent with the diathesis-stress model. PMID:27718379

The relation between social cohesion and smoking cessation among Black smokers, and the potential role of psychosocial mediators.

PubMed

Reitzel, Lorraine R; Kendzor, Darla E; Castro, Yessenia; Cao, Yumei; Businelle, Micheal S; Mazas, Carlos A; Cofta-Woerpel, Ludmila; Li, Yisheng; Cinciripini, Paul M; Ahluwalia, Jasjit S; Wetter, David W

2013-04-01

Social cohesion, the self-reported trust and connectedness between neighbors, may affect health behaviors via psychosocial mechanisms. Relations between individual perceptions of social cohesion and smoking cessation were examined among 397 Black treatment-seeking smokers. Continuation ratio logit models examined the relation of social cohesion and biochemically verified continuous smoking abstinence through 6 months post-quit. Indirect effects were examined in single mediator models using a nonparametric bootstrapping procedure. All analyses controlled for sociodemographics, tobacco dependence, and treatment. The total effect of social cohesion on continuous abstinence was non-significant (β = 0.05, p = 0.10). However, social cohesion was associated with social support, positive affect, negative affect, and stress, which, in turn, were each associated with abstinence in adjusted models (ps < 0.05). Results suggest that social cohesion may facilitate smoking cessation among Black smokers through desirable effects on psychosocial mechanisms that can result from living in a community with strong interpersonal connections.

Companionship in the neighborhood context: older adults' living arrangements and perceptions of social cohesion.

PubMed

Bromell, Lea; Cagney, Kathleen A

2014-03-01

This study investigated the impact of neighborhood social cohesion on the perceived companionship of nearly 1,500 community-dwelling older adults from the Neighborhood, Organization, Aging and Health project (NOAH), a Chicago-based study of older adult well-being in the neighborhood context. We hypothesized that the relationship between neighborhood-level social cohesion and individual residents' reports of companionship would be more pronounced among those who lived alone than those who resided with others. Controlling for age, gender, education, race, marital status, length of neighborhood residence, and self-rated health, neighborhood social cohesion predicted companionship among those who lived alone; for a one-unit increase in neighborhood social cohesion, the odds of reporting companionship increased by half. In contrast, social cohesion did not predict the companionship of those who resided with others. The results suggest that older adults who live alone particularly profit from the benefits of socially cohesive neighborhood environments. © The Author(s) 2013.

The Relation between Social Cohesion and Smoking Cessation among Black Smokers, and the Potential Role of Psychosocial Mediators

PubMed Central

Reitzel, Lorraine R.; Kendzor, Darla E.; Castro, Yessenia; Cao, Yumei; Businelle, Micheal S.; Mazas, Carlos A.; Cofta-Woerpel, Ludmila; Li, Yisheng; Cinciripini, Paul M.; Ahluwalia, Jasjit S.; Wetter, David W.

2012-01-01

Background Social cohesion, the self-reported trust and connectedness between neighbors, may affect health behaviors via psychosocial mechanisms. Purpose Relations between individual perceptions of social cohesion and smoking cessation were examined among 397 Black treatment-seeking smokers. Methods Continuation ratio logit models examined the relation of social cohesion and biochemically-verified continuous smoking abstinence through 6 months post-quit. Indirect effects were examined in single mediator models using a nonparametric bootstrapping procedure. All analyses controlled for sociodemographics, tobacco dependence, and treatment. Results The total effect of social cohesion on continuous abstinence was non-significant (β=.05, p=.10). However, social cohesion was associated with social support, positive affect negative affect, and stress, which, in turn, were each associated with abstinence in adjusted models (ps<.05). Conclusions Results suggest that social cohesion may facilitate smoking cessation among Black smokers through desirable effects on psychosocial mechanisms that can result from living in a community with strong interpersonal connections. PMID:23135831

Cohesive zone model for direct silicon wafer bonding

NASA Astrophysics Data System (ADS)

Kubair, D. V.; Spearing, S. M.

2007-05-01

Direct silicon wafer bonding and decohesion are simulated using a spectral scheme in conjunction with a rate-dependent cohesive model. The cohesive model is derived assuming the presence of a thin continuum liquid layer at the interface. Cohesive tractions due to the presence of a liquid meniscus always tend to reduce the separation distance between the wafers, thereby opposing debonding, while assisting the bonding process. In the absence of the rate-dependence effects the energy needed to bond a pair of wafers is equal to that needed to separate them. When rate-dependence is considered in the cohesive law, the experimentally observed asymmetry in the energetics can be explained. The derived cohesive model has the potential to form a bridge between experiments and a multiscale-modelling approach to understand the mechanics of wafer bonding.

Sex differences in the development of perceived family cohesion and depressive symptoms in Taiwanese adolescents.

PubMed

Sze, Tat-Ming; Hsieh, Pei-Jung; Lin, Sieh-Hwa; Chen, I-Jung

2013-08-01

This study investigates the progression of family cohesion perceptions and depressive symptoms during the character development stage in adolescents. Data were used from the Taiwan Youth Project. The final sample comprised 2,690 adolescents with 1,312 girls (48.8%; M age = 13.0 yr., SD = 0.5). Latent curve growth analysis was employed to explore these developments. Seventh-grade girls reported greater family cohesion and more depressive symptoms than boys, and boys reported greater growth in family cohesion than girls. However, progression of depressive symptoms was not associated with the child's sex. Higher perceived family cohesion in Grade 7 correlated with less increase of depressive symptoms from Grades 9 to 11. The long-term positive influence of family cohesion on depressive symptoms is discussed.

Kinetic energy density and agglomerate abrasion rate during blending of agglomerates into powders.

PubMed

Willemsz, Tofan A; Hooijmaijers, Ricardo; Rubingh, Carina M; Tran, Thanh N; Frijlink, Henderik W; Vromans, Herman; van der Voort Maarschalk, Kees

2012-01-23

Problems related to the blending of a cohesive powder with a free flowing bulk powder are frequently encountered in the pharmaceutical industry. The cohesive powder often forms lumps or agglomerates which are not dispersed during the mixing process and are therefore detrimental to blend uniformity. Achieving sufficient blend uniformity requires that the blending conditions are able to break up agglomerates, which is often an abrasion process. This study was based on the assumption that the abrasion rate of agglomerates determines the required blending time. It is shown that the kinetic energy density of the moving powder bed is a relevant parameter which correlates with the abrasion rate of agglomerates. However, aspects related to the strength of agglomerates should also be considered. For this reason the Stokes abrasion number (St(Abr)) has been defined. This parameter describes the ratio between the kinetic energy density of the moving powder bed and the work of fracture of the agglomerate. The St(Abr) number is shown to predict the abrasion potential of agglomerates in the dry-mixing process. It appeared possible to include effects of filler particle size and impeller rotational rate into this concept. A clear relationship between abrasion rate of agglomerates and the value of St(Abr) was demonstrated. Copyright © 2011 Elsevier B.V. All rights reserved.

How predation shapes the social interaction rules of shoaling fish

PubMed Central

Rosén, Emil; Ioannou, Christos C.; Rogell, Björn; Perna, Andrea; Ramnarine, Indar W.; Kolm, Niclas

2017-01-01

Predation is thought to shape the macroscopic properties of animal groups, making moving groups more cohesive and coordinated. Precisely how predation has shaped individuals' fine-scale social interactions in natural populations, however, is unknown. Using high-resolution tracking data of shoaling fish (Poecilia reticulata) from populations differing in natural predation pressure, we show how predation adapts individuals' social interaction rules. Fish originating from high predation environments formed larger, more cohesive, but not more polarized groups than fish from low predation environments. Using a new approach to detect the discrete points in time when individuals decide to update their movements based on the available social cues, we determine how these collective properties emerge from individuals' microscopic social interactions. We first confirm predictions that predation shapes the attraction–repulsion dynamic of these fish, reducing the critical distance at which neighbours move apart, or come back together. While we find strong evidence that fish align with their near neighbours, we do not find that predation shapes the strength or likelihood of these alignment tendencies. We also find that predation sharpens individuals' acceleration and deceleration responses, implying key perceptual and energetic differences associated with how individuals move in different predation regimes. Our results reveal how predation can shape the social interactions of individuals in groups, ultimately driving differences in groups' collective behaviour. PMID:28855361

Atomic adsorption on graphene with a single vacancy: systematic DFT study through the periodic table of elements

NASA Astrophysics Data System (ADS)

Pašti, Igor A.; Jovanović, Aleksandar; Dobrota, Ana S.; Mentus, Slavko V.; Johansson, Börje; Skorodumova, Natalia V.

Vacancies in graphene present sites of altered chemical reactivity and open possibilities to tune graphene properties by defect engineering. The understanding of chemical reactivity of such defects is essential for successful implementation of carbon materials in advanced technologies. We report the results of a systematic DFT study of atomic adsorption on graphene with a single vacancy for the elements of rows 1 to 6 of the Periodic Table of Elements (PTE), excluding lanthanides. The calculations have been performed using PBE, long-range dispersion interaction-corrected PBE (PBE+D2 and PBE+D3) and non-local vdW-DF2 functional. We find that most elements strongly bind to the vacancy, except for the elements of groups 11 and 12, and noble gases, for which the contribution of dispersion interaction to bonding is most significant. The strength of the interaction with the vacancy correlates with the cohesive energy of the elements in their stable phases: the higher the cohesive energy is the stronger bonding to the vacancy can be expected. As most atoms can be trapped at the SV site we have calculated the potentials of dissolution and found that in most cases the metals adsorbed at the vacancy are more "noble" than they are in their corresponding stable phases.

Atomic adsorption on graphene with a single vacancy: systematic DFT study through the periodic table of elements.

PubMed

Pašti, Igor A; Jovanović, Aleksandar; Dobrota, Ana S; Mentus, Slavko V; Johansson, Börje; Skorodumova, Natalia V

2018-01-03

Vacancies in graphene present sites of altered chemical reactivity and open possibilities to tune graphene properties by defect engineering. The understanding of chemical reactivity of such defects is essential for successful implementation of carbon materials in advanced technologies. We report the results of a systematic DFT study of atomic adsorption on graphene with a single vacancy for the elements of rows 1-6 of the periodic table of elements (PTE), excluding lanthanides. The calculations have been performed using the PBE, long-range dispersion interaction-corrected PBE (PBE+D2 and PBE+D3) and non-local vdW-DF2 functionals. We find that most elements strongly bind to the vacancy, except for the elements of groups 11 and 12, and noble gases, for which the contribution of dispersion interaction to bonding is most significant. The strength of the interaction with the vacancy correlates with the cohesive energy of the elements in their stable phases: the higher the cohesive energy is, the stronger bonding to the vacancy can be expected. As most atoms can be trapped at the SV site we have calculated the potentials of dissolution and found that in most cases the metals adsorbed at the vacancy are more "noble" than they are in their corresponding stable phases.

Improved blend and tablet properties of fine pharmaceutical powders via dry particle coating.

PubMed

Huang, Zhonghui; Scicolone, James V; Han, Xi; Davé, Rajesh N

2015-01-30

The improvements in the flow and packing of fine pharmaceutical powder blends due to dry coating of micronized acetaminophen (mAPAP, ∼11μm), a model poorly flowing drug, are quantified. Poor flow and packing density of fine excipients (∼20μm) allowed testing the hypothesis that dry coating of cohesive API may counteract poor flow and packing of fine pharmaceutical powder blends. Further, fine excipients could improve compaction and reduce segregation tendency. It was found that flow function coefficient (FFC) and bulk density enhancements for 10%, 30%, and 60% (w/w), API loading blends with dry coated API are significantly higher than those without coated silica. At the highest API loading, for which coarser excipients were also used as reference, the flow and packing of dry coated mAPAP blends were significantly increased regardless of the excipient particle size, exceeding those of a well compacting excipient, Avicel 102. In addition, tensile strength of tablets with fine excipients was significantly higher, indicating improved compactibility. These results show for the first time that dry coating of fine, cohesive API powder leads to significantly improved flow and packing of high API loading blends consisting of fine excipients, while achieving improved tablet compactibility, suggesting suitability for direct compaction. Copyright © 2014 Elsevier B.V. All rights reserved.

Exploring the Effect of Background Knowledge and Text Cohesion on Learning from Texts in Computer Science

ERIC Educational Resources Information Center

Gasparinatou, Alexandra; Grigoriadou, Maria

2013-01-01

In this study, we examine the effect of background knowledge and local cohesion on learning from texts. The study is based on construction-integration model. Participants were 176 undergraduate students who read a Computer Science text. Half of the participants read a text of maximum local cohesion and the other a text of minimum local cohesion.…

Cohesion: The Vital Ingredient for Successful Army Units

DTIC Science & Technology

1982-04-19

responding in military life as well.𔄀 A special problem of social cohesion directly related to social background was the integration of minority troops...forces has been a powerful verification of sociological theory concerning social cohesion and organizational effectiveness. Sociological theory does not...prevent the development of groups with social cohesion committed to the military hierarchy. 2 5 Personality of Wnit Mmbers Among the characteristics

Trajectories of childhood neighbourhood cohesion and adolescent mental health: evidence from a national Canadian cohort.

PubMed

Kingsbury, M; Kirkbride, J B; McMartin, S E; Wickham, M E; Weeks, M; Colman, I

2015-11-01

The objective of this study was to examine associations between trajectories of childhood neighbourhood social cohesion and adolescent mental health and behaviour. This study used data from the National Longitudinal Survey of Children and Youth, a nationally representative sample of Canadian children. The sample included 5577 children aged 0-3 years in 1994-1995, prospectively followed until age 12-15 years. Parental perceived neighbourhood cohesion was assessed every 2 years. Latent growth class modelling was used to identify trajectories of neighbourhood cohesion. Mental health and behavioural outcomes were self-reported at age 12-15 years. Logistic regression was used to examine associations between neighbourhood cohesion trajectories and outcomes, adjusting for potential confounders. Five distinct trajectories were identified: 'stable low' (4.2%); 'moderate increasing' (9.1%); 'stable moderate' (68.5%); 'high falling' (8.9%); and 'stable high' (9.3%). Relative to those living in stable moderately cohesive neighbourhoods, those in stable low cohesive neighbourhoods were more likely to experience symptoms of anxiety/depression [odds ratio (OR) = 1.73, 95% confidence interval (CI) 1.04-2.90] and engage in indirect aggression (OR = 1.62, 95% CI 1.07-2.45). Those with improvements in neighbourhood cohesion had significantly lower odds of hyperactivity (OR = 0.67, 95% CI 0.46-0.98) and indirect aggression (OR = 0.69, 95% CI 0.49-0.96). In contrast, those with a decline in neighbourhood cohesion had increased odds of hyperactivity (OR = 1.67, 95% CI 1.21-2.29). Those in highly cohesive neighbourhoods in early childhood were more likely to engage in prosocial behaviour ('high falling': OR = 1.93, 95% CI 1.38-2.69; 'stable high': OR = 1.89, 95% CI 1.35-2.63). These results suggest that neighbourhood cohesion in childhood may have time-sensitive effects on several domains of adolescent mental health and behaviour.

Trajectories of Childhood Neighbourhood Cohesion and Adolescent Mental Health: Evidence from a National Canadian Cohort

PubMed Central

Kingsbury, Mila; Kirkbride, James B; McMartin, Seanna E; Wickham, Maeve E; Weeks, Murray; Colman, Ian

2017-01-01

Background The objective of this study was to examine associations between trajectories of childhood neighbourhood social cohesion and adolescent mental health and behaviour. Methods This study used data from the National Longitudinal Survey of Children and Youth, a nationally representative sample of Canadian children. The sample included 5577 children aged 0-3 in 1994/95, prospectively followed until age 12-15. Parental perceived neighbourhood cohesion was assessed every two years. Latent growth class modeling was used to identify trajectories of neighbourhood cohesion. Mental health and behavioural outcomes were self-reported at age 12-15 years. Logistic regression was used to examine associations between neighbourhood cohesion trajectories and outcomes, adjusting for potential confounders. Results Five distinct trajectories were identified: ‘stable low’ (4.2%); ‘moderate increasing’ (9.1%); ‘stable moderate’ (68.5%); ‘high falling’ (8.9%); and, ‘stable high’ (9.3%). Relative to those living in stable moderately cohesive neighbourhoods, those in stable low cohesive neighbourhoods were more likely to experience symptoms of anxiety/depression (OR=1.75; 95%CI: 1.05,2.92) and engage in indirect aggression (OR=1.59; 95%CI: 1.05,2.40). Those with improvements in neighbourhood cohesion had significantly lower odds of hyperactivity (OR=0.68; 95%CI: 0.46,0.99) and indirect aggression (OR=0.68; 95%CI: 0.49,0.95). In contrast, those with a decline in neighbourhood cohesion had increased odds of hyperactivity (OR=1.65; 95%CI: 1.20,2.27). Those in highly cohesive neighbourhoods in early childhood were more likely to engage in prosocial behaviour (‘high falling’: OR=1.95; 95%CI: 1.40,2.72; ‘stable high’: OR=1.91; 95%CI: 1.37,2.66). Conclusions These results suggest that neighbourhood cohesion in childhood may have time-sensitive effects on several domains of adolescent mental health and behaviour. PMID:26169730

Differences by Sexual Orientation in Perceptions of Neighborhood Cohesion: Implications for Health.

PubMed

Henning-Smith, Carrie; Gonzales, Gilbert

2018-06-01

A large body of research documents the relationship between health and place, including the positive association between neighborhood cohesion and health. However, very little research has examined neighborhood cohesion by sexual orientation. This paper addresses that gap by examining differences in perceived neighborhood cohesion by sexual orientation. We use data from the 2016 National Health Interview Survey (n = 28,164 respondents aged 18 years and older) to examine bivariate differences by sexual orientation in four measures of neighborhood cohesion. We then use ordered logistic regression models to assess the relationship between sexual orientation and a scaled measure of neighborhood cohesion, adjusting for socio-demographic characteristics, living arrangements, health status, region, and neighborhood tenure. We find that lesbian, gay, and bisexual (LGB) adults are less likely to say that they live in a close-knit neighborhood (54.6 vs. 65.6%, p < 0.001), they can count on their neighbors (74.7 vs. 83.1%, p < 0.001), they trust their neighbors (75.5 vs. 83.7%, p < 0.001), or people in their neighborhood help each other out (72.9 vs. 83.1%, p < 0.001), compared to heterosexual adults. Even after controlling for socio-demographic factors, neighborhood cohesion scores are lower for LGB adults compared to heterosexual adults (odds ratio of better perceived neighborhood cohesion for sexual minorities: 0.70, p < 0.001). Overall, LGB adults report worse neighborhood cohesion across multiple measures, even after adjusting for individual characteristics and neighborhood tenure. Because living in a cohesive neighborhood is associated with better health outcomes, future research, community-level initiatives, and public policy efforts should focus on creating welcoming neighborhood environments for sexual minorities.

The Impact of Electronic Health Records and Teamwork on Diabetes Care Quality

PubMed Central

Graetz, Ilana; Huang, Jie; Brand, Richard; Shortell, Stephen M.; Rundall, Thomas G.; Bellows, Jim; Hsu, John; Jaffe, Marc; Reed, Mary E.

2016-01-01

Objective Evidence of the impact Electronic Health Records (EHR) on clinical outcomes remains mixed. The impact EHRs likely depends on the organizational context in which they are used. We focus on one aspect of the organizational context: cohesion of primary care teams. We examined whether team cohesion among primary care team members changed the association of EHR use and changes in clinical outcomes for patients with diabetes. Study Design We combined provider-reported primary care team cohesion with lab values for patients with diabetes collected during the staggered EHR implementation (2005–2009). We used multivariate regression models with patient-level fixed effects to assess whether team cohesion levels changed the association between outpatient EHR use and clinical outcomes for patients with diabetes. Subjects 80,611 patients with diabetes mellitus. Measures Changes in hemoglobin A1c (HbA1c) and low-density lipoprotein cholesterol (LDL-C) Results For HbA1c, EHR use was associated with an average decrease of 0.11% for patients with higher cohesion primary care teams compared with a decrease of 0.08% for patients with lower cohesion teams (difference 0.02% in HbA1c, 95%CI: 0.01–0.03). For LDL-C, EHR use was associated with a decrease of 2.15 mg/dL for patients with higher cohesion primary teams compared with a decrease of 1.42 mg/dL for patients with lower cohesion teams (difference 0.73 mg/dL, 95%CI: 0.41–1.11 mg/dL). Conclusions Patients cared for by higher cohesion primary care teams experienced modest but statistically significantly greater EHR-related health outcome improvements, compared with patients cared for by providers practicing in lower cohesion teams. PMID:26671699

Unit cohesion, traumatic exposure and mental health of military personnel.

PubMed

Kanesarajah, J; Waller, M; Zheng, W Y; Dobson, A J

2016-06-01

The benefit of military unit cohesion to morale and psychological resilience is well established. But it remains unclear whether unit cohesion modifies the association between deployment-related traumatic exposure and mental health problems. To examine the association between unit cohesion, traumatic exposure and poor mental health [symptoms of post-traumatic stress disorder (PTSD), psychological distress and alcohol dependency] and assess whether the relationship between traumatic exposure and poor mental health differs by level of unit cohesion. A self-reported cross-sectional survey of Australian military personnel deployed to Iraq or Afghanistan between 2001 and 2009. Among 11411 participants, those with low levels of unit cohesion had higher odds of PTSD symptoms [aOR (95% CI): 2.54 (1.88, 3.42)], very high psychological distress [aOR (95% CI): 4.28 (3.04, 6.02)] and a high level of alcohol problems [aOR (95% CI): 1.71 (1.32, 2.22)] compared with those reporting high unit cohesion on deployment. Higher exposure to traumatic events on deployment was associated with greater risk of PTSD symptoms, very high levels of psychological distress and high levels of alcohol problems in this cohort. However, there was no evidence of a statistically significant interaction between unit cohesion and traumatic exposures in influencing poor mental health. Our findings suggest that both unit cohesion and traumatic exposure are independently associated with poor mental health. Efforts to improve military unit cohesion may help to improve the mental health resilience of military personnel, regardless of their level of traumatic exposure. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A theory of adhesion at a bimetallic interface - Overlap effects.

NASA Technical Reports Server (NTRS)

Ferrante, J.; Smith, J. R.

1973-01-01

A preliminary calculation of the chemical bonding adhesive interaction between metal surfaces is provided. In this first theory the Hohenberg and Kohn formalism is used to give the bimetallic adhesive binding energy versus separation. The close-packed planes of Al, Mg, and Zn are considered. The effect of simple overlap of the metal-vacuum distributions is determined. The importance of registry between contact surfaces is ascertained. A minimum in the binding energy curve is exhibited for all combinations. The theoretical predictions agree with trends in bond strengths taken from available experimental data. An insight into the mechanisms involved in metallic transfer is given. The relationship between adhesive energies, cohesive energies, and surface energies is discussed.

Development of bio-sourced binder to metal injection moulding

NASA Astrophysics Data System (ADS)

Royer, Alexandre; Barrière, Thierry; Gelin, Jean-Claude

2016-10-01

In the MIM process the binder play the most important role. It provides fluidity of the feedstock mixture for injection molding and adhesion of the powder to keep the molded shape. The binder must provide strength and cohesion for the molded part, must be easy to be removed from the molded part, and must be the recyclable, environmentally friendly and economical ones. The goal of this study is to develop a binder environmentally friendly. For this, a study of formulation based on polyethylene glycol, because of is water debinding properties, was made. Polylactic acid and Polyhydroxyalkanoates were investigated as bio sourced polymers. The chemical, miscibility and rheological behavior of the binder formulation were investigated.

Fracture-Based Mesh Size Requirements for Matrix Cracks in Continuum Damage Mechanics Models

NASA Technical Reports Server (NTRS)

Leone, Frank A.; Davila, Carlos G.; Mabson, Gerald E.; Ramnath, Madhavadas; Hyder, Imran

2017-01-01

This paper evaluates the ability of progressive damage analysis (PDA) finite element (FE) models to predict transverse matrix cracks in unidirectional composites. The results of the analyses are compared to closed-form linear elastic fracture mechanics (LEFM) solutions. Matrix cracks in fiber-reinforced composite materials subjected to mode I and mode II loading are studied using continuum damage mechanics and zero-thickness cohesive zone modeling approaches. The FE models used in this study are built parametrically so as to investigate several model input variables and the limits associated with matching the upper-bound LEFM solutions. Specifically, the sensitivity of the PDA FE model results to changes in strength and element size are investigated.

Size-depressed critical temperatures for the order-disorder transition of FePt, CoPt, FePb, Cu2S, and ZnS nanostructures

NASA Astrophysics Data System (ADS)

Jiang, R.; Zhou, Z. F.; Yang, X. X.; Guo, N. G.; Qi, W. H.; Sun, C. Q.

2013-01-01

The size dependency of the critical temperature (TC) for the order-disorder phase transitions of both the bimetallic and the chalcogenide nanoclusters is shown to follow the rule of bond order-length-strength correlation. The loss of the cohesive energy of the undercoordinated atoms in the surface skin dictates the structural stability. Theoretical reproduction of the size TC trends of FePt, CoPt, FePb, Cu2S, and ZnS nanostructures not only confirms our expectations without involving the concepts of surface energy or entropy used for continuum bulk materials but also provides guideline for engineering nanostructured alloys or compounds.

Evaluative Testing of Sheep Ranching Site 5LA2316, 5LA2366, and 5LA2359 on the Pinon Canyon Maneuver Site, Las Animas County, Colorado

DTIC Science & Technology

2009-06-01

postcard. Sincerely, Steven L. De Vore, Archeologist (402) 437-5392 Ext. 141 steve_de_vore@nps.gov Enclosures Federal laws protect the resources on...known Coulomb equation, S = c + • tan D Where S is shear strength (in units of stress), c is cohesion, is normal stress, and U is the angle of...1 9 9 9 9 - H H h- _; J _J J 0 J y :> ^ K 00 •~r. 3 Q i -a c in de te rm ir in de te rm ir al co ho l w in do w g in de te rm ir ^ ite

Bedform development and morphodynamics in mixed cohesive sediment substrates: the importance of winnowing and flocculation

NASA Astrophysics Data System (ADS)

Ye, Leiping; Parsons, Daniel; Manning, Andrew

2016-04-01

There remains a lack of process-based knowledge of sediment dynamics within flows over bedforms generated in complex mixtures of cohesionless sand and biologically-active cohesive muds in natural estuarine flow systems. The work to be presented forms a part of the UK NERC "COHesive BEDforms (COHBED)" project which aims to fill this gap in knowledge. Herein results from a field survey in sub-tidal zone of Dee estuary (NW, England) and a set of large-scale laboratory experiments, conducted using mixtures of non-cohesive sands, cohesive muds and Xanthan gum (as a proxy for the biological stickiness of Extracellular Polymeric Substances (EPS)) will be presented. The results indicate the significance of biological-active cohesive sediments in controlling winnowing rates and flocculation dynamics, which contributes significantly to rates of bedform evolution.

Neighborhood Social Cohesion and Sleep Outcomes in the Native Hawaiian and Pacific Islander National Health Interview Survey.

PubMed

Young, Marielle C; Gerber, Monica W; Ash, Tayla; Horan, Christine M; Taveras, Elsie M

2018-05-16

Native Hawaiians and Pacific Islanders (NHPIs) have the lowest attainment of healthy sleep duration among all racial and ethnic groups in the United States. We examined associations of neighborhood social cohesion with sleep duration and quality. Cross-sectional analysis of 2,464 adults in the NHPI National Health Interview Survey (2014). Neighborhood social cohesion was categorized as a continuous and categorical variable into low (<12), medium (12-14) and high (>15) according to tertiles of the distribution of responses. We used multinomial logistic regression to examine the adjusted odds ratio of short and long sleep duration relative to intermediate sleep duration. We used binary logistic regression for dichotomous sleep quality outcomes. Sleep outcomes were modeled as categorical variables. 40% of the cohort reported short (<7 hours) sleep duration and only 4% reported long (>9 hours) duration. Mean (SE, range) social cohesion score was 12.4 units (0.11, 4-16) and 23% reported low social cohesion. In multivariable models, each 1 SD decrease in neighborhood social cohesion score was associated with higher odds of short sleep duration (OR: 1.14, 95% CI: 1.02, 1.29). Additionally, low social cohesion was associated with increased odds of short sleep duration (OR: 1.53, 95% CI: 1.10, 2.13). No associations between neighborhood social cohesion and having trouble falling or staying asleep and feeling well rested were found. Low neighborhood social cohesion is associated with short sleep duration in NHPIs.

The Relationship of Individual Difference and Group Process Variables with Self-Managed Team Performance: A Field Investigation

DTIC Science & Technology

2001-12-15

emotional stability, openness to experience, agreeableness, learning and performance goal orientation) and process variables ( social cohesion and group...both subjective performance measures and 6 of the 7 objective performance measures over that of social cohesion . Social cohesion predicted unique...variance in team member satisfaction over that of group potency. Additionally, social cohesion mediated the relationship between agreeableness and team

Formal and Informal Work Group Relationships With Performance: A Moderation Model Using Social

DTIC Science & Technology

2006-03-01

networks can be divided into two main categories: formal and informal (Scott, 2000). Similar distinctions have been made between task and social cohesion (Mullen...Cooper, 1994; Carron, Widmeyer, & Brawley, 1985; Zaccaro & Lowe, 1986; Zaccaro & McCoy, 1988). Social cohesion has been defined as...performance and social cohesion and performance (Beal et al., 2003). This move toward a multidimensional view of cohesion is consistent with the

Neighborhood Social Cohesion and Depressive Symptoms Among Latinos: Does Use of Community Resources for Physical Activity Matter?

PubMed

Perez, Lilian G; Arredondo, Elva M; McKenzie, Thomas L; Holguin, Margarita; Elder, John P; Ayala, Guadalupe X

2015-10-01

Greater neighborhood social cohesion is linked to fewer depressive symptoms and greater physical activity, but the role of physical activity on the relationship between neighborhood social cohesion and depression is poorly understood. The purpose of the study was to examine the effects of physical activity on the association between neighborhood social cohesion and depressive symptoms. Multivariate logistic regression tested the moderation of self-reported leisure-time moderate-to-vigorous physical activity (LTMVPA) and active use of parks or recreational facilities on the association between neighborhood social cohesion and depressive symptoms among 295 randomly selected Latino adults who completed a face-to-face interview. After adjusting for age, gender, and income, neighborhood social cohesion and depressive symptoms were inversely related (OR = 0.8; 95% CI: 0.5-1.2). Active use of parks or recreational facilities moderated the association between neighborhood social cohesion and depressive symptoms but meeting the recommendations for LTMVPA did not. Latinos who reported active use of parks or recreational facilities and higher levels of neighborhood social cohesion had fewer depressive symptoms than peers who did not use these spaces. Future studies are needed to test strategies for promoting active use of parks or recreational facilities to address depression in Latinos.

Group cohesion and social support of the nurses in a special unit and a general unit in Korea.

PubMed

Ko, Yu Kyung

2011-07-01

To identify the degree of group cohesion and social support of nurses in special and general units in hospitals in Korea, and to compare group cohesion and social support between the two groups. The level of commitment nurses have to their organizations has been shown to correlate with work group cohesion and social support. The participants were 1751 nurses who were working in Korean hospitals. Data were collected using a structured questionnaire and were analysed using SAS. The statistical methods included: descriptive statistics, t-test, anova and Pearson's correlation coefficients. Group cohesion of nurses on special wards was significantly higher than for nurses on general wards. No significant difference was found between types of units in terms of social support. The degree of group cohesion was significantly different in terms of the respondents' clinical experience, position, religion, job satisfaction, number of supportive superiors and number of supportive peers. A statistically significant correlation was found between group cohesion scores and degree of social support. Hospital management can accomplish their goals more effectively through knowledge of the level of group cohesion, superior support and peer support for nursing staff in accordance with unit specialty. © 2011 The Author. Journal compilation © 2011 Blackwell Publishing Ltd.

The association between EHRs and care coordination varies by team cohesion.

PubMed

Graetz, Ilana; Reed, Mary; Shortell, Stephen M; Rundall, Thomas G; Bellows, Jim; Hsu, John

2014-02-01

To examine whether primary care team cohesion changes the association between using an integrated outpatient-inpatient electronic health record (EHR) and clinician-rated care coordination across delivery sites. Self-administered surveys of primary care clinicians in a large integrated delivery system, collected in 2005 (N=565), 2006 (N=678), and 2008 (N=626) during the staggered implementation of an integrated EHR (2005-2010), including validated questions on team cohesion. Using multivariable regression, we examined the combined effect of EHR use and team cohesion on three dimensions of care coordination across delivery sites: access to timely and complete information, treatment agreement, and responsibility agreement. Among clinicians working in teams with higher cohesion, EHR use was associated with significant improvements in reported access to timely and complete information (53.5 percent with EHR vs. 37.6 percent without integrated-EHR), agreement on treatment goals (64.3 percent vs. 50.6 percent), and agreement on responsibilities (63.9 percent vs. 55.2 percent, all p<.05). We found no statistically significant association between use of the integrated-EHR and reported care coordination in less cohesive teams. The association between EHR use and reported care coordination varied by level of team cohesion. EHRs may not improve care coordination in less cohesive teams. © Health Research and Educational Trust.

Cohesion, leadership, mental health stigmatisation and perceived barriers to care in UK military personnel.

PubMed

Jones, Norman; Campion, Ben; Keeling, Mary; Greenberg, Neil

2018-02-01

Military research suggests a significant association between leadership, cohesion, mental health stigmatisation and perceived barriers to care (stigma/BTC). Most studies are cross sectional, therefore longitudinal data were used to examine the association of leadership and cohesion with stigma/BTC. Military personnel provided measures of leadership, cohesion, stigma/BTC, mental health awareness and willingness to discuss mental health following deployment (n = 2510) and 4-6 months later (n = 1636). At follow-up, baseline leadership and cohesion were significantly associated with stigma/BTC; baseline cohesion alone was significantly associated with awareness of and willingness to discuss mental health at follow-up. Over time, changes in perceived leadership and cohesion were significantly associated with corresponding changes in stigma/BTC levels. Stigma/BTC content was similar in both surveys; fear of being viewed as weak and being treated differently by leaders was most frequently endorsed while thinking less of a help-seeking team member and unawareness of potential help sources were least common. Effective leadership and cohesion building may help to reduce stigma/BTC in military personnel. Mental health awareness and promoting the discussion of mental health matters may represent core elements of supportive leader behaviour. Perceptions of weakness and fears of being treated differently represent a focus for stigma/BTC reduction.

The importance of cohesion and enjoyment for the fitness improvement of 8-10-year-old children participating in a team and individual sport school-based physical activity intervention.

PubMed

Elbe, Anne-Marie; Wikman, Johan Michael; Zheng, Miky; Larsen, Malte Nejst; Nielsen, Glen; Krustrup, Peter

2017-04-01

This study investigates the enjoyment and cohesion of school children participating in a school-based high-intensity physical activity (PA) intervention. Both enjoyment and cohesion have been found to be important factors for adherence to regular physical and sport activity, an important outcome of PA interventions. The sample consisted of 300 pupils (mean age: 9.3 years; 52.7% female) assigned to a team sport intervention, an individual sport intervention, or a control group for 10 months. The Physical Activity Enjoyment Scale and Youth Sport Environment Questionnaire were used to measure enjoyment and cohesion. The Yo-Yo IR1C test determined fitness improvements. Results showed that enjoyment and cohesion (social) measured at the beginning of the intervention significantly predict fitness improvements achieved after 10 months. No differing developmental effects over time could be found in the intervention groups with regard to cohesion and enjoyment when comparing them to the control group. However, enjoyment and cohesion (social) significantly decreased in the groups that performed individual sports. Team sports seem to be more advantageous for the development of enjoyment and cohesion, which are both factors that positively impact the health outcomes of the intervention.

Neighborhood social cohesion and depressive symptoms among Latinos: Does use of community resources for physical activity matter?

PubMed Central

Perez, Lilian G.; Arredondo, Elva M.; McKenzie, Thomas L.; Holguin, Margarita; Elder, John P.; Ayala, Guadalupe X.

2017-01-01

Background Greater neighborhood social cohesion is linked to fewer depressive symptoms and greater physical activity, but the role of physical activity on the relationship between neighborhood social cohesion and depression is poorly understood. The purpose of the study was to examine the effects of physical activity on the association between neighborhood social cohesion and depressive symptoms. Methods Multivariate logistic regression tested the moderation of self-reported leisure time moderate-to vigorous-physical activity (LTMVPA) and active use of parks or recreational facilities on the association between neighborhood social cohesion and depressive symptoms among 295 randomly selected Latino adults who completed a face-to-face interview. Results After adjusting for age, gender, and income, neighborhood social cohesion and depressive symptoms were inversely related (OR=0.8; 95% CI: 0.5–1.2). Active use of parks or recreational facilities moderated the association between neighborhood social cohesion and depressive symptoms but meeting the recommendations for LTMVPA did not. Latinos who reported active use of parks or recreational facilities and higher levels of neighborhood social cohesion had fewer depressive symptoms than peers who did not use these spaces. Conclusions Future studies are needed to test strategies for promoting active use of parks or recreational facilities to address depression in Latinos. PMID:25599244

Mind the gap! Automated concept map feedback supports students in writing cohesive explanations.

PubMed

Lachner, Andreas; Burkhart, Christian; Nückles, Matthias

2017-03-01

Many students are challenged with the demand of writing cohesive explanations. To support students in writing cohesive explanations, we developed a computer-based feedback tool that visualizes cohesion deficits of students' explanations in a concept map. We conducted three studies to investigate the effectiveness of such feedback as well as the underlying cognitive processes. In Study 1, we found that the concept map helped students identify potential cohesion gaps in their drafts and plan remedial revisions. In Study 2, students with concept map feedback conducted revisions that resulted in more locally and globally cohesive, and also more comprehensible, explanations than the explanations of students who revised without concept map feedback. In Study 3, we replicated the findings of Study 2 by and large. More importantly, students who had received concept map feedback on a training explanation 1 week later wrote a transfer explanation without feedback that was more cohesive than the explanation of students who had received no feedback on their training explanation. The automated concept map feedback appears to particularly support the evaluation phase of the revision process. Furthermore, the feedback enabled novice writers to acquire sustainable skills in writing cohesive explanations. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Dentin-Composite Bond Strength Measurement Using the Brazilian Disk Test

PubMed Central

Carrera, Carola A.; Chen, Yung-Chung; Li, Yuping; Rudney, Joel; Aparicio, Conrado; Fok, Alex

2016-01-01

Objectives This study presents a variant of the Brazilian disk test (BDT) for assessing the bond strength between composite resins and dentin. Methods Dentin-composite disks (φ 5 mm × 2 mm) were prepared using either Z100 or Z250 (3M ESPE) in combination with one of three adhesives, Adper Easy Bond (EB), Adper Scotchbond Multi-Purpose (MP) and Adper Single Bond (SB), and tested under diametral compression. Acoustic emission (AE) and digital image correlation (DIC) were used to monitor debonding of the composite from the dentin ring. A finite element (FE) model was created to calculate the bond strengths using the failure loads. Fracture modes were examined by scanning electron microscopy (SEM). Results Most specimens fractured along the dentin-resin composite interface. DIC and AE confirmed interfacial debonding immediately before fracture of the dentin ring. Results showed that the mean bond strength with EB (14.9±1.9 MPa) was significantly higher than with MP (13.2±2.4 MPa) or SB (12.9±3.0 MPa) (p<0.05); no significant difference was found between MP and SB (p>0.05). Z100 (14.5±2.3 MPa) showed higher bond strength than Z250 (12.7±2.5 MPa) (p<0.05). Majority of specimens (91.3%) showed an adhesive failure mode. EB failed mostly at the dentin-adhesive interface, whereas MP at the composite-adhesive interface; specimens with SB failed at the composite-adhesive interface and cohesively in the adhesive. Conclusions The BDT variant showed to be a suitable alternative for measuring the bond strength between dentin and composite, with zero premature failure, reduced variability in the measurements, and consistent failure at the dentin-composite interface. PMID:27395367

Oxygen inhibition layer of composite resins: effects of layer thickness and surface layer treatment on the interlayer bond strength.

PubMed

Bijelic-Donova, Jasmina; Garoushi, Sufyan; Lassila, Lippo V J; Vallittu, Pekka K

2015-02-01

An oxygen inhibition layer develops on surfaces exposed to air during polymerization of particulate filling composite. This study assessed the thickness of the oxygen inhibition layer of short-fiber-reinforced composite in comparison with conventional particulate filling composites. The effect of an oxygen inhibition layer on the shear bond strength of incrementally placed particulate filling composite layers was also evaluated. Four different restorative composites were selected: everX Posterior (a short-fiber-reinforced composite), Z250, SupremeXT, and Silorane. All composites were evaluated regarding the thickness of the oxygen inhibition layer and for shear bond strength. An equal amount of each composite was polymerized in air between two glass plates and the thickness of the oxygen inhibition layer was measured using a stereomicroscope. Cylindrical-shaped specimens were prepared for measurement of shear bond strength by placing incrementally two layers of the same composite material. Before applying the second composite layer, the first increment's bonding site was treated as follows: grinding with 1,000-grit silicon-carbide (SiC) abrasive paper, or treatment with ethanol or with water-spray. The inhibition depth was lowest (11.6 μm) for water-sprayed Silorane and greatest (22.9 μm) for the water-sprayed short-fiber-reinforced composite. The shear bond strength ranged from 5.8 MPa (ground Silorane) to 36.4 MPa (water-sprayed SupremeXT). The presence of an oxygen inhibition layer enhanced the interlayer shear bond strength of all investigated materials, but its absence resulted in cohesive and mixed failures only with the short-fiber-reinforced composite. Thus, more durable adhesion with short-fiber-reinforced composite is expected. © 2014 Eur J Oral Sci.

Evolution of Mat Strength from the Paleoarchean to the Modern: A Record of Evolving Microbial Communities?

NASA Astrophysics Data System (ADS)

Tice, M.; Pope, M.; Thornton, D.

2011-12-01

Fossil microbial mats, i.e. surface-attached communities of benthic microorganisms, form the most extensive record of life on Earth. Qualitatively changing mat morphologies from 3.43-0.56-billion-years-ago may reflect the evolution of microorganism communities or changing environmental conditions. However, mat morphogenesis is not well understood or easily quantifiable, making interpretation of the mat record difficult. We show that microbial mat cohesion increased from ~1 Pa to ~13 Pa at 2.7-billion-years-ago (Ga), and has remained high for most of the rest of Earth history. This initial increase may represent an early increase in the productivity of mat communities, a change in the composition of extracellular polymeric substances (EPS) produced by mat-formers, or a change in the composition of seawater affecting EPS strength. The appearance of early high-strength communities was coincident with the appearance of voids representing gas bubbles in the apices of conical stromatolites; together, these changes may record the emergence of productive mat communities dominated by oxygenic cyanobacteria. The earliest high-strength communities, like early bubble-forming conical stromatolites, grew in low-energy environments. The appearance of high-strength communities in shallow-water environments starting 2.63-2.52 Ga coincided with the appearance of the first barrier reef complexes. We hypothesize that the first oxygenic cyanobacteria were most competitive with anoxygenic phototrophs in diffusion-limited environments. As the cyanobacteria became more proficient at oxygenic photosynthesis, they eventually outcompeted anoxygenic phototrophs in higher-energy environments. Competition with higher strength seaweed and grazing by metazoans has displaced mat communities from essentially all modern high-energy niches.

Are diverse societies less cohesive? Testing contact and mediated contact theories.

PubMed

McKenna, Sarah; Lee, Eunro; Klik, Kathleen A; Markus, Andrew; Hewstone, Miles; Reynolds, Katherine J

2018-01-01

Previous research has demonstrated that there is a negative relationship between ethnic diversity in a local community and social cohesion. Often the way social cohesion is assessed, though, varies across studies and only some aspects of the construct are included (e.g., trust). The current research explores the relationship between diversity and social cohesion across a number of indicators of social cohesion including neighbourhood social capital, safety, belonging, generalized trust, and volunteering. Furthermore, social psychological theories concerning the role of positive contact and its impact on feelings of threat are investigated. Using a sample of 1070 third generation 'majority' Australians and structural equation modelling (SEM), findings suggest ethnic diversity is related to positive intergroup contact, and that contact showed beneficial impacts for some indicators of social cohesion both directly and indirectly through reducing perceived threat. When interethnic contact and perceived threat are included in the model there is no direct negative effect between diversity and social cohesion. The theoretical implications of these findings are outlined including the importance of facilitating opportunities for positive contact in diverse communities.

Perceived Social Cohesion, Frequency of Going Out, and Depressive Symptoms in Older Adults

PubMed Central

Choi, Namkee G.; Kim, Jinseok; DiNitto, Diana M.; Marti, C. Nathan

2015-01-01

Objective: To examine both cross-sectional and longitudinal relationships between older adults’ perceptions of social cohesion in their community and depressive symptoms and the potential mediating effect of the frequency of going outside one’s home/building. Method: Using two waves (T1 and T2) of the National Health and Aging Trend Study (n = 5,326), gender-stratified structural equation models were estimated to determine direct and indirect effects of perceived social cohesion on depressive symptoms. Results: At T1, both perceived cohesion and frequency of going out were directly associated with depressive symptoms; however, perceived cohesion predicted frequency of going out only for women. At T2, only frequency of going out was directly associated with depressive symptoms, although perceived cohesion predicted frequency of going out for both genders. T1 perceived cohesion did not predict T2 depressive symptoms. T1 depressive symptoms were the strongest predictor of T2 depressive symptoms. Conclusion: The findings underscore the importance of enhancing the social environment in promoting mental health in late life through active aging. PMID:28138478

Perceived Social Cohesion, Frequency of Going Out, and Depressive Symptoms in Older Adults: Examination of Longitudinal Relationships.

PubMed

Choi, Namkee G; Kim, Jinseok; DiNitto, Diana M; Marti, C Nathan

2015-01-01

Objective: To examine both cross-sectional and longitudinal relationships between older adults' perceptions of social cohesion in their community and depressive symptoms and the potential mediating effect of the frequency of going outside one's home/building. Method: Using two waves (T1 and T2) of the National Health and Aging Trend Study ( n = 5,326), gender-stratified structural equation models were estimated to determine direct and indirect effects of perceived social cohesion on depressive symptoms. Results: At T1, both perceived cohesion and frequency of going out were directly associated with depressive symptoms; however, perceived cohesion predicted frequency of going out only for women. At T2, only frequency of going out was directly associated with depressive symptoms, although perceived cohesion predicted frequency of going out for both genders. T1 perceived cohesion did not predict T2 depressive symptoms. T1 depressive symptoms were the strongest predictor of T2 depressive symptoms. Conclusion: The findings underscore the importance of enhancing the social environment in promoting mental health in late life through active aging.

Are diverse societies less cohesive? Testing contact and mediated contact theories

PubMed Central

Lee, Eunro; Klik, Kathleen A.; Markus, Andrew; Hewstone, Miles; Reynolds, Katherine J.

2018-01-01

Previous research has demonstrated that there is a negative relationship between ethnic diversity in a local community and social cohesion. Often the way social cohesion is assessed, though, varies across studies and only some aspects of the construct are included (e.g., trust). The current research explores the relationship between diversity and social cohesion across a number of indicators of social cohesion including neighbourhood social capital, safety, belonging, generalized trust, and volunteering. Furthermore, social psychological theories concerning the role of positive contact and its impact on feelings of threat are investigated. Using a sample of 1070 third generation ‘majority’ Australians and structural equation modelling (SEM), findings suggest ethnic diversity is related to positive intergroup contact, and that contact showed beneficial impacts for some indicators of social cohesion both directly and indirectly through reducing perceived threat. When interethnic contact and perceived threat are included in the model there is no direct negative effect between diversity and social cohesion. The theoretical implications of these findings are outlined including the importance of facilitating opportunities for positive contact in diverse communities. PMID:29596501

The association between social cohesion and physical activity in canada: A multilevel analysis.

PubMed

Yip, Calvin; Sarma, Sisira; Wilk, Piotr

2016-12-01

Although previous research has shown that social cohesion may promote physical activity, social cohesion at the individual level was not always differentiated from social cohesion at the community level, and studies were often limited to specific population subgroups or geographical areas. We addressed the above limitations through the use of a multilevel modelling approach and nationally-representative data from the 2009-2014 Canadian Community Health Survey. Physical activity level was operationalized as average daily energy expenditure; social cohesion was assessed by self-rated sense of belonging to the local community; and communities were represented by Canada's Forward Sortation Areas. The sample included 245,150 respondents from 1570 communities. Geographical location was found to explain a significant proportion (4.1%) of the overall variance in physical activity level. After adjusting for age, sex, household income, education and urban-rural status, both individual- and community-level social cohesion were found to be positively associated with physical activity (p<0.001 for both). Thus, efforts to promote social cohesion and integration within communities may also promote physical activity and overall health.

Aurora A-dependent CENP-A phosphorylation at inner centromeres protects bioriented chromosomes against cohesion fatigue.

PubMed

Eot-Houllier, Grégory; Magnaghi-Jaulin, Laura; Fulcrand, Géraldine; Moyroud, François-Xavier; Monier, Solange; Jaulin, Christian

2018-05-14

Sustained spindle tension applied to sister centromeres during mitosis eventually leads to uncoordinated loss of sister chromatid cohesion, a phenomenon known as "cohesion fatigue." We report that Aurora A-dependent phosphorylation of serine 7 of the centromere histone variant CENP-A (p-CENP-AS7) protects bioriented chromosomes against cohesion fatigue. Expression of a non-phosphorylatable version of CENP-A (CENP-AS7A) weakens sister chromatid cohesion only when sister centromeres are under tension, providing the first evidence of a regulated mechanism involved in protection against passive cohesion loss. Consistent with this observation, p-CENP-AS7 is detected at the inner centromere where it forms a discrete domain. The depletion or inhibition of Aurora A phenocopies the expression of CENP-AS7A and we show that Aurora A is recruited to centromeres in a Bub1-dependent manner. We propose that Aurora A-dependent phosphorylation of CENP-A at the inner centromere protects chromosomes against tension-induced cohesion fatigue until the last kinetochore is attached to spindle microtubules.

Bond strength comparison of 2 self-etching primers over a 3-month storage period.

PubMed

Trites, Brian; Foley, Timothy F; Banting, David

2004-12-01

The purpose of this in vitro study was to evaluate the shear-peel bond strength of 2 self-etching primer systems, Transbond Plus (3M/ Unitek, Monrovia, Calif) and First Step (Reliance Orthodontic Products, Itasca, Ill), with their respective adhesives, and compare them with a control adhesive system (Transbond XT, 3M/ Unitek) over a 3-month period. Two hundred seventy extracted human premolars were obtained and randomly divided into 9 groups of 30 teeth. Metal orthodontic brackets were bonded to the enamel, and each adhesive group was stored for 24 horrs (T1), 30 days (T2), or 3 months (T3) in deionized water at 37 degrees C. All bonded specimens were thermocycled at 10 degrees C and 50 degrees C for 24 hours before debonding. Brackets were debonded by using a shear-peel load on a testing machine at a cross-head speed of 2 mm/min. Bond failure was also evaluated. The shear-peel bond strengths of the 3 bonding systems were clinically acceptable with the possible exception of First Step at 30-day storage. Repeated measures analysis of variance showed a statistically significant (P < .0001) difference in mean bond strengths between the 3 adhesive systems. The shear-peel bond strength of the adhesives over the 3 time intervals showed statistically significant (P = .005) changes. In each group, there were statistically significant differences in shear-peel bond strength between time intervals T1-T2 and T2-T3 for Transbond Plus and T2-T3 for First Step. The change in mean shear-peel bond strength of the 3 adhesives demonstrated a consistent pattern of behavior over the 3 storage intervals. The lowest mean shear-peel bond strength values were noted at the 30-day storage. Bond failure analysis (adhesive remnant index) demonstrated mainly cohesive bond failures.

Shear Bond Strength between Fiber-Reinforced Composite and Veneering Resin Composites with Various Adhesive Resin Systems.

PubMed

AlJehani, Yousef A; Baskaradoss, Jagan K; Geevarghese, Amrita; AlShehry, Marey A; Vallittu, Pekka K

2016-07-01

The aim of this research was to evaluate the shear bond strength of different laboratory resin composites bonded to a fiber-reinforced composite substrate with some intermediate adhesive resins. Mounted test specimens of a bidirectional continuous fiber-reinforced substrate (StickNet) were randomly assigned to three equal groups. Three types of commercially available veneering resin composites - BelleGlass®, Sinfony®, and GC Gradia® were bonded to these specimens using four different adhesive resins. Half the specimens per group were stored for 24 hours; the remaining were stored for 30 days. There were 10 specimens in the test group (n). The shear bond strengths were calculated and expressed in MPa. Data were analyzed statistically, and variations in bond strength within each group were additionally evaluated by calculating the Weibull modulus. Shear bond values of those composites are influenced by the different bonding resins and different indirect composites. There was a significant difference in the shear bond strengths using different types of adhesive resins (p = 0.02) and using different veneering composites (p < 0.01). Belle-Glass® had the highest mean shear bond strength when bonded to StickNet substrate using both Prime & Bond NT and OptiBond Solo Plus. Sinfony® composite resin exhibited the lowest shear bond strength values when used with the same adhesive resins. The adhesive mode of failure was higher than cohesive with all laboratory composite resins bonded to the StickNet substructure at both storage times. Water storage had a tendency to lower the bond strengths of all laboratory composites, although the statistical differences were not significant. Within the limitations of this study, it was found that bonding of the veneering composite to bidirectional continuous fiber-reinforced substrate is influenced by the brand of the adhesive resin and veneering composite. © 2015 by the American College of Prosthodontists.

Validation of French and German versions of a Perceived Neighborhood Social Cohesion Questionnaire among young Swiss males, and its relationship with substance use.

PubMed

Dupuis, Marc; Studer, Joseph; Henchoz, Yves; Deline, Stéphane; Baggio, Stéphanie; N'Goran, Alexandra; Mohler-Kuo, Meichun; Gmel, Gerhard

2016-02-01

This study main purpose was the validation of both French and German versions of a Perceived Neighborhood Social Cohesion Questionnaire. The sample group comprised 5065 Swiss men from the "Cohort Study on Substance Use Risk Factors." Multigroup Confirmatory factor analysis showed that a three-factor model fits the data well, which substantiates the generalizability of Perceived Neighborhood Social Cohesion Questionnaire factor structure, regardless of the language. The Perceived Neighborhood Social Cohesion Questionnaire demonstrated excellent homogeneity (α = 95) and split-half reliability (r = .96). The Perceived Neighborhood Social Cohesion Questionnaire was sensitive to community size and participants' financial situation, confirming that it also measures real social conditions. Finally, weak but frequent correlations between Perceived Neighborhood Social Cohesion Questionnaire and alcohol, cigarette, and cannabis dependence were measured. © The Author(s) 2014.

Mode I Cohesive Law Characterization of Through-Crack Propagation in a Multidirectional Laminate

NASA Technical Reports Server (NTRS)

Bergan, Andrew C.; Davila, Carlos G.; Leone, Frank A.; Awerbuch, Jonathan; Tan, Tein-Min

2014-01-01

A method is proposed and assessed for the experimental characterization of through-the-thickness crack propagation in multidirectional composite laminates with a cohesive law. The fracture toughness and crack opening displacement are measured and used to determine a cohesive law. Two methods of computing fracture toughness are assessed and compared. While previously proposed cohesive characterizations based on the R-curve exhibit size effects, the proposed approach results in a cohesive law that is a material property. The compact tension specimen configuration is used to propagate damage while load and full-field displacements are recorded. These measurements are used to compute the fracture toughness and crack opening displacement from which the cohesive law is characterized. The experimental results show that a steady-state fracture toughness is not reached. However, the proposed method extrapolates to steady-state and is demonstrated capable of predicting the structural behavior of geometrically-scaled specimens.

Influence of dry cohesion on the micro- and macro-mechanical properties of dense polydisperse powders & grains

NASA Astrophysics Data System (ADS)

Kievitsbosch, Robert; Smit, Hendrik; Magnanimo, Vanessa; Luding, Stefan; Taghizadeh, Kianoosh

2017-06-01

Understanding how cohesive granular materials behave is of interest for many industrial applications, such as pharmaceutical or food and civil engineering. Models of the behaviour of granular materials on the microscopic scale can be used to obtain macroscopic continuum relations by a micro-macro transition approach. The Discrete Element Method (DEM) is used to inspect the influence of cohesion on the micro and macro behaviour of granular assemblies by using an elasto-plastic cohesive contact model. Interestingly, we observe that frictional samples prepared with different cohesion values show a significant difference in pressure and coordination number in the jammed regime; the differences become more pronounced when packings are closer to the jamming density, i.e. the lowest density where the system is mechanically stable. Furthermore, we observe that cohesion has an influence on the jamming density for frictional samples, but there is no influence on the jamming density for frictionless samples.

Composition, concentration and deprivation: exploring their association with social cohesion among different ethnic groups in the UK.

PubMed

Bécares, Laia; Stafford, Mai; Laurence, James; Nazroo, James

2011-01-01

Although studies in the US have shown an association between the ethnic residential composition of an area and reports of decreased social cohesion among its residents, this association is not clear in the UK, and particularly for ethnic minority groups. The current study analyses a merged dataset from the 2005 and 2007 Citizenship Survey to assess the evidence for an association between social cohesion and ethnic residential concentration, composition and area deprivation across different ethnic groups in the UK. Results of the multilevel regression models show that, after adjusting for area deprivation, increased levels of social cohesion are found in areas of greater ethnic residential heterogeneity. Although different patterns emerge across ethnic groups and the measure of social cohesion used, findings consistently show that it is area deprivation, and not ethnic residential heterogeneity, which erodes social cohesion in the UK.

Cohesive and mixed sediment in the Regional Ocean Modeling System (ROMS v3.6) implemented in the Coupled Ocean-Atmosphere-Wave-Sediment Transport Modeling System (COAWST r1234)

NASA Astrophysics Data System (ADS)

Sherwood, Christopher R.; Aretxabaleta, Alfredo L.; Harris, Courtney K.; Rinehimer, J. Paul; Verney, Romaric; Ferré, Bénédicte

2018-05-01

We describe and demonstrate algorithms for treating cohesive and mixed sediment that have been added to the Regional Ocean Modeling System (ROMS version 3.6), as implemented in the Coupled Ocean-Atmosphere-Wave-Sediment Transport Modeling System (COAWST Subversion repository revision 1234). These include the following: floc dynamics (aggregation and disaggregation in the water column); changes in floc characteristics in the seabed; erosion and deposition of cohesive and mixed (combination of cohesive and non-cohesive) sediment; and biodiffusive mixing of bed sediment. These routines supplement existing non-cohesive sediment modules, thereby increasing our ability to model fine-grained and mixed-sediment environments. Additionally, we describe changes to the sediment bed layering scheme that improve the fidelity of the modeled stratigraphic record. Finally, we provide examples of these modules implemented in idealized test cases and a realistic application.

A multilevel analysis of social ties and social cohesion among Latinos and their neighborhoods: results from Chicago.

PubMed

Almeida, Joanna; Kawachi, Ichiro; Molnar, Beth E; Subramanian, S V

2009-09-01

Research suggests that, among Latinos, there are health benefits associated with living in a neighborhood populated with coethnics. While social networks and social cohesion are the proposed explanation for the salubrious effect and are assumed to be characteristics of Latino immigrant enclaves, evidence for this is limited. We used multilevel regression to test the relative contribution of individual race/ethnicity and neighborhood concentration of Mexican Americans as predictors of social networks and social cohesion. After accounting for personal characteristics, we found a negative association between neighborhood concentration of Mexican Americans and social cohesion. Among Latinos, living in a neighborhood with increased coethnics was associated with increased social ties. Compared to non-Latino whites, Mexican Americans reported more social ties but lower social cohesion. Contrary to the assumption that Mexican immigrant enclaves beget social cohesion, we did not find this to be true in Chicago neighborhoods.

Noninvasive pit and fissure sealing: microtensile bond strength to intact bovine enamel of different pit and fissure sealants in a simplified fissure model.

PubMed

Papacchini, Federica; Cury, Alvaro H; Goracci, Cecilia; Chieffi, Nicoletta; Tay, Franklin R; Polimeni, Antonella; Ferrari, Marco

2006-12-01

To measure the microtensile bond strength of different pit and fissure sealants in a simplified fissure model. Twenty extracted bovine mandibular permanent incisors were randomly divided into 4 groups for treatment: G1: 35% phosphoric acid/Clinpro Sealant; G2: 35% phosphoric acid/Delton; G3: Non-Rinse Conditioner/Dyract Seal; G4: 20% polyacrylic acid/Fuji IILC. Each tooth was sectioned into 6 pieces (4 x 6 mm) of buccal enamel. SEM examination was used to confirm the presence of aprismatic enamel on each tooth. Using a spacer, two pieces of etched enamel were secured to a glass slide at a mean distance of 0.6+/-0.1 mm. The space between enamel substrates was then etched/conditioned and sealed with different materials according to the tested groups. By serially cutting each double-bonded sample, multiple beam-shaped specimens about 0.8mm(2) in cross section were obtained and tested in tension (0.5 mm/min) until failure occurred at either one of the two stressed interfaces. Failure modes were classified by stereomicroscopy. G1 and G2 showed statistically higher bond strengths than G3 and G4. G4 demonstrated the significantly lowest bond strength. Failures were mostly adhesive in G1, G2, G3, and mainly cohesive/mixed in G4. According to this model, resin-based materials (Clinpro Sealant, Delton) showed better microtensile bond strength than compomer (Dyract Seal) or resin-modified glass ionomer (Fuji IILC).

Metal-ceramic bond strength between a feldspathic porcelain and a Co-Cr alloy fabricated with Direct Metal Laser Sintering technique.

PubMed

Dimitriadis, Konstantinos; Spyropoulos, Konstantinos; Papadopoulos, Triantafillos

2018-02-01

The aim of the present study was to record the metal-ceramic bond strength of a feldspathic dental porcelain and a Co-Cr alloy, using the Direct Metal Laser Sintering technique (DMLS) for the fabrication of metal substrates. Ten metal substrates were fabricated with powder of a dental Co-Cr alloy using DMLS technique (test group) in dimensions according to ISO 9693. Another ten substrates were fabricated with a casing dental Co-Cr alloy using classic casting technique (control group) for comparison. Another three substrates were fabricated using each technique to record the Modulus of Elasticity ( E ) of the used alloys. All substrates were examined to record external and internal porosity. Feldspathic porcelain was applied on the substrates. Specimens were tested using the three-point bending test. The failure mode was determined using optical and scanning electron microscopy. The statistical analysis was performed using t-test. Substrates prepared using DMLS technique did not show internal porosity as compared to those produced using the casting technique. The E of control and test group was 222 ± 5.13 GPa and 227 ± 3 GPa, respectively. The bond strength was 51.87 ± 7.50 MPa for test group and 54.60 ± 6.20 MPa for control group. No statistically significant differences between the two groups were recorded. The mode of failure was mainly cohesive for all specimens. Specimens produced by the DMLS technique cover the lowest acceptable metal-ceramic bond strength of 25 MPa specified in ISO 9693 and present satisfactory bond strength for clinical use.

Effects of silica coating and silane surface conditioning on the bond strength of rebonded metal and ceramic brackets.

PubMed

Atsü, Saadet; Çatalbaş, Bülent; Gelgör, İbrahim Erhan

2011-01-01

The aim of this study was to evaluate the effects of tribochemical silica coating and silane surface conditioning on the bond strength of rebonded metal and ceramic brackets. Twenty debonded metal and 20 debonded ceramic brackets were randomly assigned to receive one of the following surface treatments (n=10 for each group): (1) sandblasting (control); (2) tribochemical silica coating combined with silane. Brackets were rebonded to the enamel surface on the labial and lingual sides of premolars with a light-polymerized resin composite. All specimens were stored in distilled water for 1 week and then thermocycled (5,000 cycles) between 5-55ºC. Shear bond strength values were measured using a universal testing machine. Student's t-test was used to compare the data (α=0.05). Failure mode was assessed using a stereomicroscope, and the treated and non-treated bracket surfaces were observed by scanning electron microscopy. Rebonded ceramic brackets treated with silica coating followed by silanization had significantly greater bond strength values (17.7±4.4 MPa) than the sandblasting group (2.4±0.8 MPa, P<0.001). No significant difference was observed between the rebonded metal brackets treated with silica coating with silanization (15±3.9 MPa) and the sandblasted brackets (13.6±3.9 MPa). Treated rebonded ceramic specimens primarily exhibited cohesive failure in resin and adhesive failure at the enamel-adhesive interface. In comparison to sandblasting, silica coating with aluminum trioxide particles followed by silanization resulted in higher bond strengths of rebonded ceramic brackets.

Perceptions of communication, family adaptability and cohesion: a comparison of adolescents newly diagnosed with cancer and their parents.

PubMed

Phillips-Salimi, Celeste R; Robb, Sheri L; Monahan, Patrick O; Dossey, Amy; Haase, Joan E

2014-01-01

To describe and compare adolescent and parent perspectives on communication, family adaptability and cohesion, as well as relationships among these variables, during the first month of an adolescent's cancer diagnosis. Seventy adolescent-parent dyads were enrolled as part of a larger multi-site study. The adolescents ranged in age from 11 to 19, and 61% were males. Parents were predominately mothers (83%). Dyads were predominately non-Hispanic Caucasian (63%). Measures included the Parent-Adolescent Communication Scale and the Family Adaptability and Cohesion Evaluation Scale (FACES II). Paired t-tests, Pearson correlations, intra-class correlation coefficients and multiple linear regression analyses were completed. Adolescent scores on communication, family adaptability and cohesion were significantly lower than parent scores. The inter-dyadic agreement between adolescents and parents was low. Communication, family adaptability and cohesion were examined separately for adolescents and for parents, and significant relationships were found. Both adolescent- and parent-perceived communication was significantly associated with family adaptability and cohesion outcomes. Differences were found in adolescent and parent perceptions of communication, family adaptability and cohesion. When both adolescents and parents had better perceived communication, this was associated with better perceived family adaptability and cohesion. Results suggest that the development of interventions to enhance adolescent-parent communication could help foster better family adaptability and cohesion, which may ultimately impact their psychological adjustment. In addition, understanding the degree to which adolescents and parents disagree on their perceptions, including the results that parents generally have more favorable perceptions, may be a useful starting point when developing interventions.

Perceptions of Communication, Family Adaptability, and Cohesion: A Comparison of Adolescents Newly Diagnosed with Cancer and their Parents

PubMed Central

Phillips-Salimi, Celeste R.; Robb, Sheri L.; Monahan, Patrick O.; Dossey, Amy; Haase, Joan E.

2017-01-01

Purpose Describe and compare adolescent and parent perspectives on communication, family adaptability and cohesion, as well as relationships among these variables, during the first month of the adolescent’s cancer diagnosis. Methods Seventy 70 adolescent-parent dyads were enrolled as part of a larger multi-site study. Adolescents ranged in age from 11–19 and 61% were males. Parents were predominately mothers (83%). Dyads were predominately non-Hispanic Caucasian (63%). Measures included the Parent-Adolescent Communication Scale and the Family Adaptability and Cohesion Evaluation Scale (FACES II). Paired t tests, Pearson correlations, intra-class correlation coefficients, and multiple linear regression analyses were completed. Results Adolescent scores on communication, family adaptability, and cohesion were significantly lower than parent scores. The inter-dyadic agreement between adolescents and parents was low. Communication, family adaptability, and cohesion were examined separately for adolescents and for parents, significant relationships were found. Both adolescent- and parent-perceived communication was significantly associated with family adaptability and cohesion outcomes. Conclusions Differences were found in adolescent and parent perceptions of communication, family adaptability, and cohesion. When both adolescents and parents had better perceived communication, it was associated with better perceived family adaptability and cohesion. Results suggest the development of interventions to enhance adolescent-parent communication could help foster better family adaptability and cohesion which may ultimately impact their psychological adjustment. In addition, understanding the degree to which adolescents and parents disagree on their perceptions, including the results that parents generally have more favorable perceptions, may be a useful starting point when developing interventions. PMID:24501152

Is it Ethnic Fractionalization or Social Exclusion, Which Affects Social Cohesion?

PubMed

van Staveren, Irene; Pervaiz, Zahid

2017-01-01

The theory about missing links of economic growth often lags behind the empirical estimations of such links. A consensus has emerged that ethnic fractionalization has a negative impact on growth, also when controlled for income inequality. Often, although implicitly, the assumed channel is social cohesion. We analyse the effect of fractionalization on social cohesion with a different inequality measure, namely a social measure of inequality: the Inclusion of Minorities Index. Our results indicate that it is social exclusion , which reduces social cohesion, rather than diversity as such . We conclude that future studies of social cohesion and its relation to growth may benefit from using measures of social exclusion next to ethnic diversity.

Atomistic Cohesive Zone Models for Interface Decohesion in Metals

NASA Technical Reports Server (NTRS)

Yamakov, Vesselin I.; Saether, Erik; Glaessgen, Edward H.

2009-01-01

Using a statistical mechanics approach, a cohesive-zone law in the form of a traction-displacement constitutive relationship characterizing the load transfer across the plane of a growing edge crack is extracted from atomistic simulations for use within a continuum finite element model. The methodology for the atomistic derivation of a cohesive-zone law is presented. This procedure can be implemented to build cohesive-zone finite element models for simulating fracture in nanocrystalline or ultrafine grained materials.

Flow Function of Pharmaceutical Powders Is Predominantly Governed by Cohesion, Not by Friction Coefficients.

PubMed

Leung, Lap Yin; Mao, Chen; Srivastava, Ishan; Du, Ping; Yang, Chia-Yi

2017-07-01

The purpose of this study was to demonstrate that the flow function (FFc) of pharmaceutical powders, as measured by rotational shear cell, is predominantly governed by cohesion but not friction coefficients. Driven by an earlier report showing an inverse correlation between FFc and the cohesion divided by the corresponding pre-consolidation stress (Wang et al. 2016. Powder Tech. 294:105-112), we performed analysis on a large data set containing 1130 measurements from a ring shear tester and identified a near-perfect inverse correlation between the FFc and cohesion. Conversely, no correlation was found between FFc and friction angles. We also conducted theoretical analysis and estimated such correlations based on Mohr-Coulomb failure model. We discovered that the correlation between FFc and cohesion can sustain as long as the angle of internal friction at incipient flow is not significantly larger than the angle of internal friction at steady-state flow, a condition covering almost all pharmaceutical powders. The outcome of this study bears significance in pharmaceutical development. Because the cohesion value is strongly influenced by the interparticle cohesive forces, this study effectively shows that it is more efficient to improve the pharmaceutical powder flow by lowering the interparticle cohesive forces than by lowering the interparticle frictions. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Social embeddedness as a mechanism for linking social cohesion to well-being among older adults: moderating effect of gender

PubMed Central

Momtaz, Yadollah Abolfathi; Haron, Sharifah Azizah; Ibrahim, Rahimah; Hamid, Tengku Aizan

2014-01-01

Background The positive effect of social cohesion on well-being in older adults has been well documented. However, relatively few studies have attempted to understand the mechanisms by which social cohesion influences well-being. The main aim of the current study is to identify social pathways in which social cohesion may contribute to well-being. Methods The data for this study (taken from 1,880 older adults, aged 60 years and older) were drawn from a national survey conducted during 2008–2009. The survey employed a two-stage stratified sampling process for data collection. Structural equation modeling was used to test mediating and moderating analyses. Results The proposed model documented a good fit to the data (GFI =98; CFI =0.99; RMSEA =0.04). The findings from bootstrap analysis and the Sobel test revealed that the impact of social cohesion on well-being is significantly mediated by social embeddedness (Z=5.62; P<0.001). Finally, the results of a multigroup analysis test showed that social cohesion influences well-being through the social embeddedness mechanism somewhat differently for older men than women. Conclusion The findings of this study, in addition to supporting the importance of neighborhood social cohesion for the well-being of older adults, also provide evidence that the impact of social cohesion towards well-being is mediated through the mechanism of social embeddedness. PMID:24904206

Social embeddedness as a mechanism for linking social cohesion to well-being among older adults: moderating effect of gender.

PubMed

Momtaz, Yadollah Abolfathi; Haron, Sharifah Azizah; Ibrahim, Rahimah; Hamid, Tengku Aizan

2014-01-01

The positive effect of social cohesion on well-being in older adults has been well documented. However, relatively few studies have attempted to understand the mechanisms by which social cohesion influences well-being. The main aim of the current study is to identify social pathways in which social cohesion may contribute to well-being. The data for this study (taken from 1,880 older adults, aged 60 years and older) were drawn from a national survey conducted during 2008-2009. The survey employed a two-stage stratified sampling process for data collection. Structural equation modeling was used to test mediating and moderating analyses. The proposed model documented a good fit to the data (GFI =98; CFI =0.99; RMSEA =0.04). The findings from bootstrap analysis and the Sobel test revealed that the impact of social cohesion on well-being is significantly mediated by social embeddedness (Z=5.62; P<0.001). Finally, the results of a multigroup analysis test showed that social cohesion influences well-being through the social embeddedness mechanism somewhat differently for older men than women. The findings of this study, in addition to supporting the importance of neighborhood social cohesion for the well-being of older adults, also provide evidence that the impact of social cohesion towards well-being is mediated through the mechanism of social embeddedness.

Winnowing and Flocculation in Bio-physical Cohesive Substrate: A Flume Experimental and Estuarine Study

NASA Astrophysics Data System (ADS)

Ye, L.; Parsons, D. R.; Manning, A. J.

2016-12-01

Cohesive sediment, or mud, is ubiquitously found in most aqueous environments, such as coasts and estuaries. The study of cohesive sediment behaviors requires the synchronous description of mutual interactions of grains (e.g., winnowing and flocculation), their physical properties (e.g., grain size) and also the ambient water. Herein, a series of flume experiments (14 runs) with different substrate mixtures of sand-clay-EPS (Extracellular Polymeric Substrates: secreted by aquatic microorganisms) are combined with an estuarine field survey (Dee estuary, NW England) to investigate the behavior of suspensions over bio-physical cohesive substrates. The experimental results indicate that winnowing and flocculation occur pervasively in bio-physical cohesive flow systems. Importantly however, the evolution of the bed and bedform dynamics and hence turbulence production can be lower when cohesivity is high. The estuarine survey also revealed that the bio-physical cohesion provided by both the clay and microorganism fractions in the bed, that pervasively exists in many natural estuarine systems, plays a significant role in controlling the interactions between bed substrate and sediment suspension and deposition, including controlling processes such as sediment winnowing, flocculation and re-deposition. Full understanding of these processes are essential in advancing sediment transport modelling and prediction studies across natural estuarine systems and the work will report on an improved conceptual model for sediment sorting deposition in bio-physical cohesive substrates.

Family cohesion and posttraumatic intrusion and avoidance among war veterans: a 20-year longitudinal study.

PubMed

Zerach, Gadi; Solomon, Zahava; Horesh, Danny; Ein-Dor, Tsachi

2013-02-01

The bi-directional relationships between combat-induced posttraumatic symptoms and family relations are yet to be understood. The present study assesses the longitudinal interrelationship of posttraumatic intrusion and avoidance and family cohesion among 208 Israeli combat veterans from the 1982 Lebanon War. Two groups of veterans were assessed with self-report questionnaires 1, 3 and 20 years after the war: a combat stress reaction (CSR) group and a matched non-CSR control group. Latent Trajectories Modeling showed that veterans of the CSR group reported higher intrusion and avoidance than non-CSR veterans at all three points of time. With time, there was a decline in these symptoms in both groups, but the decline was more salient among the CSR group. The latter also reported lower levels of family cohesion. Furthermore, an incline in family cohesion levels was found in both groups over the years. Most importantly, Autoregressive Cross-Lagged Modeling among CSR and non-CSR veterans revealed that CSR veterans' posttraumatic symptoms in 1983 predicted lower family cohesion in 1985, and lower family cohesion, in turn, predicted posttraumatic symptoms in 2002. The findings suggest that psychological breakdown on the battlefield is a marker for future family cohesion difficulties. Our results lend further support for the bi-directional mutual effects of posttraumatic symptoms and family cohesion over time.

Diagenetic Features in Yellowknife Bay, Gale Crater, Mars: Implications for Substrate Rheology and Potential Gas Release

NASA Technical Reports Server (NTRS)

Kah, L. C.; Stack, K; Siebach, K.; Grotzinger, J.; Summer, D.; Farien, A.; Oehler, D.; Schieber, J.; Leville, R.; Edgar, L;

Failure mechanisms of fibrin-based surgical tissue adhesives

NASA Astrophysics Data System (ADS)

Sierra, David Hugh

A series of studies was performed to investigate the potential impact of heterogeneity in the matrix of multiple-component fibrin-based tissue adhesives upon their mechanical and biomechanical properties both in vivo and in vitro. Investigations into the failure mechanisms by stereological techniques demonstrated that heterogeneity could be measured quantitatively and that the variation in heterogeneity could be altered both by the means of component mixing and delivery and by the formulation of the sealant. Ex vivo tensile adhesive strength was found to be inversely proportional to the amount of heterogeneity. In contrast, in vivo tensile wound-closure strength was found to be relatively unaffected by the degree of heterogeneity, while in vivo parenchymal organ hemostasis in rabbits was found to be affected: greater heterogeneity appeared to correlate with an increase in hemostasis time and amount of sealant necessary to effect hemostasis. Tensile testing of the bulk sealant showed that mechanical parameters were proportional to fibrin concentration and that the physical characteristics of the failure supported a ductile mechanism. Strain hardening as a function of percentage of strain, and strain rate was observed for both concentrations, and syneresis was observed at low strain rates for the lower fibrin concentration. Blister testing demonstrated that burst pressure and failure energy were proportional to fibrin concentration and decreased with increasing flow rate. Higher fibrin concentration demonstrated predominately compact morphology debonds with cohesive failure loci, demonstrating shear or viscous failure in a viscoelastic rubbery adhesive. The lower fibrin concentration sealant exhibited predominately fractal morphology debonds with cohesive failure loci, supporting an elastoviscous material condition. The failure mechanism for these was hypothesized and shown to be flow-induced ductile fracture. Based on these findings, the failure mechanism was stochastic in nature because the mean failure energy and burst pressure values were not predictive of locus and morphology. Instead, flow rate and fibrin concentration showed the most predictive value, with the outcome best described as a probability distribution rather than a specific deterministic outcome.

Validation of a New Elastoplastic Constitutive Model Dedicated to the Cyclic Behaviour of Brittle Rock Materials

NASA Astrophysics Data System (ADS)

Cerfontaine, B.; Charlier, R.; Collin, F.; Taiebat, M.

2017-10-01

Old mines or caverns may be used as reservoirs for fuel/gas storage or in the context of large-scale energy storage. In the first case, oil or gas is stored on annual basis. In the second case pressure due to water or compressed air varies on a daily basis or even faster. In both cases a cyclic loading on the cavern's/mine's walls must be considered for the design. The complexity of rockwork geometries or coupling with water flow requires finite element modelling and then a suitable constitutive law for the rock behaviour modelling. This paper presents and validates the formulation of a new constitutive law able to represent the inherently cyclic behaviour of rocks at low confinement. The main features of the behaviour evidenced by experiments in the literature depict a progressive degradation and strain of the material with the number of cycles. A constitutive law based on a boundary surface concept is developed. It represents the brittle failure of the material as well as its progressive degradation. Kinematic hardening of the yield surface allows the modelling of cycles. Isotropic softening on the cohesion variable leads to the progressive degradation of the rock strength. A limit surface is introduced and has a lower opening than the bounding surface. This surface describes the peak strength of the material and allows the modelling of a brittle behaviour. In addition a fatigue limit is introduced such that no cohesion degradation occurs if the stress state lies inside this surface. The model is validated against three different rock materials and types of experiments. Parameters of the constitutive laws are calibrated against uniaxial tests on Lorano marble, triaxial test on a sandstone and damage-controlled test on Lac du Bonnet granite. The model is shown to reproduce correctly experimental results, especially the evolution of strain with number of cycles.

Symptom fluctuations, self-esteem, and cohesion during group cognitive behaviour therapy for early psychosis.

PubMed

Lecomte, Tania; Leclerc, Claude; Wykes, Til

2018-03-01

Group cohesion has been linked to positive changes in self-esteem and in symptoms during group psychotherapy in people with psychosis. These changes may be linked to changes in symptoms as fluctuations in self-esteem have been linked to symptom fluctuations. We aimed to determine the relationship between these three factors - group cohesion, self-esteem, and symptoms - during group cognitive behaviour therapy for psychosis (GCBTp). We hypothesized that group cohesion would precede changes in symptoms and self-esteem and that improvements in self-esteem would precede improvements in symptoms. This is an uncontrolled longitudinal study recruiting from a convenience sample within two early psychosis clinics. Sixty-six individuals from first episode of psychosis treatment programmes participated in this study and received 24 sessions of a validated GCBTp protocol. Participants answered a brief questionnaire at the end of each session, measuring their group cohesion, self-esteem, and perception of their symptoms as worse, same, or better than usual. Orthogonal polynomial contrasts for time effects were estimated with a mixed model for repeated measures with a random cluster effect and revealed a quartic trend regarding changes in symptoms over the 24 sessions. Self-esteem, symptoms, and group cohesion were strongly linked during a given session. Also, self-esteem changes predicted changes in symptoms up to two sessions later, and symptoms changes predicted self-esteem changes at the next session. Group cohesion preceded improvements in both self-esteem and symptoms; self-esteem also predicted improvements in group cohesion. These results suggest that self-esteem and symptoms influence each other during therapy, with improvements in one leading to improvements in the other. Group cohesion also appears to be an essential prerequisite to positive changes in self-esteem and symptoms during GCBTp. This study emphasizes the interrelation between self-esteem improvements and symptom improvements, with improvements in one leading to improvements in the other, during group CBT for psychosis. Group cohesion, in this study, is a predictor of self-esteem and symptom improvements, suggesting that a special attention should be given to developing a strong alliance and group cohesion early on during CBT for psychosis. © 2017 The British Psychological Society.

Physical and Mechanical Properties of Surface Sediments and methane hydrate-bearing sediments in the Shenhu area of South China Sea

NASA Astrophysics Data System (ADS)

Jiang, J.; Shen, Z.; Jia, Y.

2017-12-01

Methane hydrates are superior energy resources and potential predisposing factors of geohazard. With the success in China's persistent exploitation of methane hydrates in the Shenhu area of South China Sea for 60 days, there is an increasing demand for detailed knowledge of sediment properties and hazard assessment in this area. In this paper, the physical and mechanical properties of both the surface sediments and methane hydrate-bearing sediments (MHBS) in the exploitation area, the Shenhu area of South China Sea, were investigated using laboratory geotechnical experiments, and triaxial tests were carried out on remolded sediment samples using a modified triaxial apparatus. The results show that sediments in this area are mainly silt with high moisture content, high plasticity, low permeability and low shear strength. The moisture content and permeability decrease while the shear strength increases with the increasing depth. The elastic modulus and peak strength of MHBS increase with the increasing effective confining pressure and higher hydrate saturation. The cohesion increases with higher hydrate saturation while the internal friction angle is barely affected by hydrate saturation. The obtained results demonstrate clearly that methane hydrates have significant impacts on the physical and mechanical properties of sediments and there is still a wide gap in knowledge about MHBS.

Asteroid airburst altitude vs. strength

NASA Astrophysics Data System (ADS)

Robertson, Darrel; Wheeler, Lorien; Mathias, Donovan

2016-10-01

Small NEO asteroids (<Ø140m) may not be a threat on a national or global level but can still cause a significant amount of local damage as demonstrated by the Chelyabinsk event where there was over $33 million worth of damage (1 billion roubles) and 1500 were injured, mostly due to broken glass. The ground damage from a small asteroid depends strongly on the altitude at which they "burst" where most of the energy is deposited in the atmosphere. The ability to accurately predict ground damage is useful in determining appropriate evacuation or shelter plans and emergency management.Strong asteroids, such as a monolithic boulder, fail and create peak energy deposition close to the altitude at which ram dynamic pressure exceeds the material cohesive strength. Weaker asteroids, such as a rubble pile, structurally fail at higher altitude, but it requires the increased aerodynamic pressure at lower altitude to disrupt and disperse the rubble. Consequently the resulting airbursts have a peak energy deposition at similar altitudes.In this study hydrocode simulations of the entry and break-up of small asteroids were performed to examine the effect of strength, size, composition, entry angle, and speed on the resulting airburst. This presentation will show movies of the simulations, the results of peak burst height, and the comparison to semi-analytical models.

Enhancement of the surface methane hydrate-bearing layer based on the specific microorganisms form deep seabed sediment in Japan Sea.

NASA Astrophysics Data System (ADS)

Hata, T.; Yoneda, J.; Yamamoto, K.

2017-12-01

A methane hydrate-bearing layer located near the Japan Sea has been investigated as a new potential energy resource. In this study examined the feasibility of the seabed surface sediment strength located in the Japan Sea improvement technologies for enhancing microbial induced carbonate precipitation (MICP) process. First, the authors cultivated the specific urease production bacterium culture medium from this surface methane hydrate-bearing layer in the seabed (-600m depth) of Japan Sea. After that, two types of the laboratory test (consolidated-drained triaxial tests) were conducted using this specific culture medium from the seabed in the Japan Sea near the Toyama Prefecture and high urease activities bacterium named Bacillus pasteurii. The main outcomes of this research are as follows. 1) Specific culture medium focused on the urease production bacterium can enhancement of the urease activities from the methane hydrate-bearing layer near the Japan Sea side, 2) This specific culture medium can be enhancement of the surface layer strength, 3) The microbial induced carbonate precipitation process can increase the particle size compared to that of the original particles coating the calcite layer surface, 4) The mechanism for increasing the soil strength is based on the addition of cohesion like a cement stabilized soil.

Scour in cohesive soils

DOT National Transportation Integrated Search

2015-05-01

This study of scour in cohesive soils had two objectives. The first was to introduce and demonstrate a new ex situ erosion testing device (ESTD) that can mimic the near-bed flow of open channels to erode cohesive soils within a specified range of she...

Factors associated with low unit cohesion in Australian Defence Force members who deployed to the Middle East (2001–2009)

PubMed Central

Kanesarajah, Jeeva; Waller, M; Zheng, W Y; Dobson, A J

2016-01-01

Introduction Unit cohesion has been shown to bolster the mental health of military personnel; hence, it is important to identify the characteristics that are associated with low unit cohesion, so that interventions to improve unit cohesion can be targeted and implemented. Little is known about the factors associated with low unit cohesion. This research aims to identify demographic, military service and deployment factors associated with low unit cohesion. Methods Data from a self-reported cross-sectional study of 11 411 current or ex-serving Australian military personnel deployed to Iraq or Afghanistan between 2001 and 2009 were used. Multivariable logistic regression was used to investigate the research aims. Results Being female (adjusted OR (aOR) (95% CI) 1.35 (1.21 to 1.51)), non-commissioned officer (aOR (95% CI) 1.50 (1.39 to 1.62)), lower ranked (aOR (95% CI) 1.74 (1.51 to 2.01)) or having left military service (aOR (95% CI) 1.71 (1.46 to 2.02)) was associated with reporting low unit cohesion. Potentially modifiable factors such as performing logistic roles on deployment (aOR (95% CI) 1.13 (1.01 to 1.27)), dissatisfaction with work experience on deployment such as working with colleagues who did not do what was expected of them (aOR (95% CI) 4.09 (3.61 to 4.64)), and major problems at home while deployed (aOR (95% CI) 1.50 (1.38 to 1.63)) were also associated with reporting low unit cohesion. Conclusions This is the first study to identify demographic, military service and deployment factors associated with low unit cohesion. The modifiable nature of unit cohesion means that military leaders could use this information to identify subgroups for targeted resilience interventions that may reduce vulnerabilities to mental health problems and improve the job satisfaction, preparedness and deployment experiences of serving members. PMID:26567321

Analysis of Cohesion and Collective Efficacy Profiles for the Performance of Soccer Players

PubMed Central

Leo, Francisco M.; Sánchez-Miguel, Pedro A.; Sánchez-Oliva, David; Amado, Diana; García-Calvo, Tomás

2013-01-01

The principal aims of the study were to define different profiles of cohesion and perceived efficacy in soccer players and to measure their differences in performance. The subjects were 235 soccer players in the under-18 category who played in the National League in Spain and 15 coaches whose ages ranged from 29 to 45 years. Diverse instruments to assess cohesion, perceived efficacy, and expectations of success were used in the study. Moreover, we measured playing time and performance. The results of the study proved the existence of four cohesion and efficacy profiles that presented significant differences in expectations of success, playing time, and performance. Furthermore, significant differences were found in the distribution of players in the teams as a function of performance. The main conclusion of this study is that soccer players with higher cohesion and collective efficacy levels belonged to teams that completed the season at the top-level classification. In contrast, athletes with low cohesion and collective efficacy usually played in unsuccessful teams. Coaches and sports psychologists are encouraged to promote both social and task cohesion and collective efficacy to enhance team performance. PMID:24511358

Assessing the impact of vulnerability on perceptions of social cohesion in the context of community resilience to disaster in the Blue Mountains.

PubMed

Redshaw, Sarah; Ingham, Valerie; McCutcheon, Marion; Hicks, John; Burmeister, Oliver

2018-02-01

To assess the impact of network communications, community participation and elements of vulnerability on the perception of social cohesiveness in the Blue Mountains local government area (Blue Mountains LGA). A questionnaire was administered to residents of the Blue Mountains LGA. Econometric analysis of the resulting data was undertaken. Blue Mountains LGA, Australia. One thousand one hundred and three residents of the Blue Mountains LGA responded to the questionnaire. The responses enabled the construction of variables measuring individual perceptions of community cohesiveness, their network communications and community participation. Demographic data and data on the vulnerabilities of individuals were also collected. The data were used in an econometric model which identified that network communications and community participation impacted positively on perceptions of social cohesiveness while vulnerability factors had a negative impact. Remedial action to build community cohesiveness and network communications can be expected to have a positive impact on social cohesiveness. In developing strategies to build community cohesiveness and network communication, particular care needs to be taken to ensure the inclusion of those members of society who are regarded as the most vulnerable. © 2017 National Rural Health Alliance Inc.

Team Cohesion, Player Attitude, and Performance Expectations in Simulation.

ERIC Educational Resources Information Center

Wellington, William J.; Faria, A. J.

1996-01-01

Examines the relationship of team cohesion, participant attitude, and performance expectations to actual performance results in a simulation competition. Findings indicate a strong relationship between beginning team cohesion and performance expectations and final game performance, but little relationship between beginning participant attitudes…

Of Blue Badges and Purple Cloth, the Impact of Battle Death in a Cohesive Unit

DTIC Science & Technology

1988-12-18

the small-unit level. History shows that the key to understanding the problem of death in a cohesive unit is that the danger of being killed or...cohesion and motivation are rooted in intensely personal attachments at the small-unit level. History shows that the key to understanding the problem of...without fear of mortal peril." (8) In this one sentence he shows his awareness of the necessity for leadership and cohesiveness in the face of death

The impact of neighborhood violence and social cohesion on smoking behaviors among a cohort of smokers in Mexico

PubMed Central

Fleischer, Nancy L.; Lozano, Paula; Santillán, Edna Arillo; Shigematsu, Luz Myriam Reynales; Thrasher, James F.

2016-01-01

Background Recent increases in violent crime may impact a variety of health outcomes in Mexico. We examined relationships between neighborhood-level violence and smoking behaviors in a cohort of Mexican smokers from 2011–2012, and whether neighborhood-level social cohesion modified these relationships. Methods Data were analyzed from adult smokers and recent ex-smokers who participated in Waves 5–6 of the International Tobacco Control Mexico Survey. Self-reported neighborhood violence and social cohesion were asked of Wave 6 survey participants (n=2129 current and former smokers, n=150 neighborhoods). Neighborhood-level averages for violence and social cohesion (range 4–14 and 10–25, respectively) were assigned to individuals. We used generalized estimating equations to determine associations between neighborhood indicators and individual-level smoking intensity, quit behaviors, and relapse. Results Higher neighborhood violence was associated with higher smoking intensity (Risk Ratio (RR)=1.17, 95% Confidence Interval (CI) 1.02–1.33), and fewer quit attempts (RR=0.72, 95% CI 0.61–0.85). Neighborhood violence was not associated with successful quitting or relapse. Higher neighborhood social cohesion was associated with more quit attempts and more successful quitting. Neighborhood social cohesion modified the association between neighborhood violence and smoking intensity: in neighborhoods with higher social cohesion, as violence increased, smoking intensity decreased and in neighborhoods with lower social cohesion, as violence increased, so did smoking intensity. Conclusion In the context of recent increased violence in Mexico, smokers living in neighborhoods with more violence may smoke more cigarettes per day and make fewer quit attempts than their counterparts in less violent neighborhoods. Neighborhood social cohesion may buffer the impact of violence on smoking intensity. PMID:26043898

Facing Sorrow as a Group Unites. Facing Sorrow in a Group Divides

PubMed Central

Rennung, Miriam; Göritz, Anja S.

2015-01-01

Collective gatherings foster group cohesion through providing occasion for emotional sharing among participants. However, prior studies have failed to disentangle two processes that are involved in emotional sharing: 1) focusing shared attention on the same emotion-eliciting event and 2) actively sharing one’s experiences and disclosing one’s feelings to others. To date, it has remained untested if shared attention influences group cohesion independent of active emotional sharing. Our experiment investigated the effect of shared versus individual attention on cohesion in groups of strangers. We predicted that differences in group cohesion as called forth by shared vs. individual attention are most pronounced when experiencing highly arousing negative affect, in that the act of experiencing intensely negative affect with others buffers negative affect’s otherwise detrimental effect on group cohesion. Two-hundred sixteen participants were assembled in groups of 3 to 4 people to either watch an emotion-eliciting film simultaneously on a common screen or to watch the same emotion-eliciting film clip on a laptop in front of each group member using earphones. The film clips were chosen to elicit either highly arousing negative affect or one of three other affective states representing the other poles in Russel’s Circumplex model of affect. We examined self-reported affective and cognitive group cohesion and a behavioral measure of group cohesion. Results support our buffer-hypothesis, in that experiencing intense negative affect in unison leads to higher levels of group cohesion than experiencing this affect individually despite the group setting. The present study demonstrates that shared attention to intense negative emotional stimuli affects group cohesion independently of active emotional sharing. PMID:26335924

Differences in neighborhood social cohesion and aerobic physical activity by Latino subgroup.

PubMed

Murillo, Rosenda; Echeverria, Sandra; Vasquez, Elizabeth

2016-12-01

Previous research has examined the role of neighborhood social cohesion in physical activity outcomes; however, less is known about this relationship across Latino subgroups. The purpose of our study was to examine the association between neighborhood social cohesion and aerobic leisure-time physical activity (LTPA) among Latino adults and to determine whether these associations differ by Latino subgroup. We used cross-sectional 2013-2014 National Health Interview Survey (NHIS) data on Latinos originating from 5 countries/regions (i.e., Latinos of Puerto Rican, Mexican/Mexican-American, Cuban/Cuban-American, Dominican and Central or South American origin) aged ≥18 years (n=11,126). Multivariable logistic regression models were used to estimate associations between self-reported neighborhood social cohesion and meeting aerobic LTPA guidelines. Models were adjusted for age, sex, education, and acculturation. We also investigated whether associations varied by Latino subgroup. In adjusted models for all Latino adults, compared with those reporting low social cohesion, individuals who reported high social cohesion (Odds Ratio [OR]: 1.33; 95% Confidence Interval [CI]: 1.17-1.52) were significantly more likely to meet the aerobic physical activity guideline. When stratified by Latino subgroups, among Mexican/Mexicans-Americans (OR: 1.39; 95% CI: 1.16, 1.66) and Cuban/Cuban Americans (OR: 1.73; 95% CI: 1.00, 2.97) high social cohesion was associated with meeting the aerobic activity guideline. Among Dominicans, those who reported medium social cohesion (OR: 0.52, 95% CI: 0.29, 0.93) were less likely to meet the aerobic activity guideline. When examining aerobic physical activity outcomes in the Latino population, the role of neighborhood social cohesion and the variability among Latino subgroups should be considered.

Factors associated with low neighborhood cohesion among women living with HIV impacted by social-structural inequities in British Columbia.

PubMed

Closson, Kalysha; Palmer, Alexis K; Collins, Alexandra B; Salters, Kate; Zhang, Wendy; Montaner, Julio S G; Hogg, Robert S; Parashar, Surita

2018-03-01

Built and social environments, including one's perception of their environment, are important determinants of health. The intersection of gender and HIV status may complicate the role of neighborhood cohesion in safety, personal well-being, and health outcomes for populations impacted by social and structural inequities. Among women in particular, social cohesion within the neighborhood they reside in may have a greater influence on health outcomes compared to their male counterparts. We sought to examine perception of neighborhood cohesion (validated scale with a range 0-100, with higher scores indicating higher perceived neighborhood cohesion) among women living with HIV, impacted by social-structural inequities, receiving combination antiretroviral therapy, and enrolled in the Longitudinal Investigations into Supportive Ancillary health services (LISA) study in British Columbia, Canada. Cross-sectional data on neighborhood cohesion and socio-demographic data were collected in an interviewer-administered survey. Of the 1,000 LISA participants interviewed, 908 (including 249 women and 659 men) had complete data for the variables of interest. At the bivariate level, women had worse perceived neighborhood cohesion scores compared to men (median: 56 [95% CI: 44-66] vs. 60 [95% CI: 47-71]). Multivariable model results indicated that for women living with HIV in our sample, greater neighborhood cohesion scores were positively associated with stable housing (β coefficient = 7.85; 95% CI: 3.61, 12.10, p < 0.001), and negatively associated with greater perceived HIV stigma (β coefficient = -1.19; 95% CI: -2.24 to-0.15; p = 0.025). The results illustrate the gendered nature of experiencing built and social environments, and highlight the need for women-centred interventions to address the social determinants of HIV burden associated with negative perceptions of neighborhood cohesion.

Global Landslides on Rapidly Spinning Spheroids

NASA Astrophysics Data System (ADS)

Scheeres, Daniel J.; Sanchez, P.

2013-10-01

The angle of repose and conditions for global landslides on the surfaces of small, rapidly spinning, spheroidal asteroids are studied. Applying techniques of soil mechanics, we develop a theory for, and examples of, how regolith will fail and flow in this microgravity environment. Our motivation is to develop an understanding of the "top-shaped" class of asteroids based on analytical soil mechanics. Our analysis transforms the entire asteroid surface into a local frame where we can model it as a conventional granular pile with a surface slope, acceleration and height variations as a function of the body's spin rate, shape and density. A general finding is that the lowest point on a rapidly spinning spheroid is at the equator with the effective height of surface material monotonically increasing towards the polar regions, where the height can be larger than the physical radius of the body. We study the failure conditions of both cohesionless and cohesive regolith, and develop specific predictions of the surface profile as a function of the regolith angle of friction and the maximum spin rate experienced by the body. The theory also provides simple guidelines on what the shape may look like, although we do not analyze gravitationally self-consistent evolution of the body shape. The theory is tested with soft-sphere discrete element method granular mechanics simulations to better understand the dynamical aspects of global asteroid landslides. We find significant differences between failure conditions for cohesive and cohesionless regolith. In the case of cohesive regolith, we show that extremely small values of strength (much less than that found in lunar regolith) can stabilize a surface even at very rapid spin rates. Cohesionless surfaces, as expected, fail whenever their surface slopes exceed the angle of friction. Based on our analysis we propose that global landslides and the flow of material towards the equator on spheroidal bodies are precipitated by exogenous effects such as impact induced seismic shaking or torques during planetary flybys.

Bond strength with various etching times on young permanent teeth

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, W.N.; Lu, T.C.

1991-07-01

Tensile bond strengths of an orthodontic resin cement were compared for 15-, 30-, 60-, 90-, or 120-second etching times, with a 37% phosphoric acid solution on the enamel surfaces of young permanent teeth. Fifty extracted premolars from 9- to 16-year-old children were used for testing. An orthodontic composite resin was used to bond the bracket directly onto the buccal surface of the enamel. The tensile bond strengths were tested with an Instron machine. Bond failure interfaces between bracket bases and teeth surfaces were examined with a scanning electron microscope and calculated with mapping of energy-dispersive x-ray spectrometry. The results ofmore » tensile bond strength for 15-, 30-, 60-, or 90-second etching times were not statistically different. For the 120-second etching time, the decrease was significant. Of the bond failures, 43%-49% occurred between bracket and resin interface, 12% to 24% within the resin itself, 32%-40% between resin and tooth interface, and 0% to 4% contained enamel fragments. There was no statistical difference in percentage of bond failure interface distribution between bracket base and resin, resin and enamel, or the enamel detachment. Cohesive failure within the resin itself at the 120-second etching time was less than at other etching times, with a statistical significance. To achieve good retention, to decrease enamel loss, and to reduce moisture contamination in the clinic, as well as to save chairside time, a 15-second etching time is suggested for teenage orthodontic patients.« less

Occurrence of cohesion of metals during combined plastic deformation

NASA Technical Reports Server (NTRS)

Aynbinder, S. G.; Klokova, E. F.

1980-01-01

Experiments were conducted to study the cohesion of metals with surface films of varying thickness and hardness. It was established that the deformation necessary for the occurrence of cohesion is determined by the correlation of mechanical properties of the films and the base metal. The greater the relative hardness of the film the lower the deformation necessary for the occurrence of cohesion. The films are as plastic as the base metal prevent cohesion, since in this case it is impossible for sections of metal to appear that are free of contaminants. The physical perculiarities of metals that determine their capability for coalescence under conditions of dry friction are the relative hardness and plasticity of the oxide films formed on their surface under atmospheric conditions.

Validation of a brief form of the Perceived Neighborhood Social Cohesion questionnaire.

PubMed

Dupuis, Marc; Baggio, Stéphanie; Gmel, Gerhard

2017-02-01

The aim of this study was the validation of a brief form of the Perceived Neighborhood Social Cohesion questionnaire using data from 5065 men from the "Cohort Study on Substance-Use Risk Factors." A 9-item scale covering three factors was proposed. Excellent indices of internal consistency were measured (α = .93). The confirmatory factor analyses resulted in acceptable fit indices supporting measurement invariance across French and German forms. Significant correlations were found between the brief form of the Perceived Neighborhood Social Cohesion questionnaire, and satisfaction and self-reported health, providing evidence of the concurrent validity of the scale. Perceived neighborhood social cohesion, and depression and suicide attempts were negatively associated, sustaining the protective effect of perceived social cohesion.

The Role of Preceptorship and Group Cohesion on Newly Licensed Registered Nurses' Satisfaction and Intent to Stay.

PubMed

Bontrager, Sarah; Hart, Patricia L; Mareno, Nicole

2016-03-01

Thirteen percent of newly licensed registered nurses (NLRNs) vacate their first job after 1 year, and 37% report that they feel ready to change jobs. Turnover can lead to consistent and detrimental nursing shortages in nursing units, as well as increased costs for health care systems. A descriptive, prospective, cross-sectional design was used to understand how preceptor role effectiveness and group cohesion affect NLRNs' satisfaction and intent to stay. NLRNs reported high levels of perceived preceptor role effectiveness, group cohesion, and job satisfaction, with only moderate levels of intent to stay. Statistically significant relationships were found among preceptor role effectiveness, job satisfaction, and intent to stay, as well as among group cohesion, job satisfaction, and intent to stay. Preceptor role effectiveness and group cohesion are predictors of NLRNs' level of job satisfaction. Job satisfaction is a predictor of NLRNs' intent to stay. Effective preceptors and positive group cohesion are factors that are important to NLRNs' job satisfaction and intent to stay. Copyright 2016, SLACK Incorporated.

Erosion properties of cohesive sediments in the Colorado River in Grand Canyon

USGS Publications Warehouse

Akahori, R.; Schmeeckle, M.W.; Topping, D.J.; Melis, T.S.

2008-01-01

Cohesive sediment deposits characterized by a high fraction of mud (silt plus clay) significantly affect the morphology and ecosystem of rivers. Potentially cohesive sediment samples were collected from deposits in the Colorado River in Marble and Grand Canyons. The erosion velocities of these samples were measured in a laboratory flume under varying boundary shear stresses. The non-dimensional boundary shear stress at which erosion commenced showed a systematic deviation from that of non-cohesive sediments at mud fractions greater than 0.2. An empirical relation for the boundary shear stress threshold of erosion as a function of mud fraction was proposed. The mass erosion rate was modelled using the Ariathurai-Partheniades equation. The erosion rate parameter of this equation was found to be a strong function of mud fraction. Under similar boundary shear stress and sediment supply conditions in the Colorado River, cohesive lateral eddy deposits formed of mud fractions in excess of 0.2 will erode less rapidly than non-cohesive deposits. Copyright ?? 2008 John Wiley & Sons, Ltd.

A season-long team-building intervention: examining the effect of team goal setting on cohesion.

PubMed

Senécal, Julie; Loughead, Todd M; Bloom, Gordon A

2008-04-01

The purpose of the current study was to determine whether the implementation of a season-long team-building intervention program using team goal setting increased perceptions of cohesion. The participants were 86 female high school basketball players from 8 teams. The teams were randomly assigned to either an experimental team goal-setting or control condition. Each participant completed the Group Environment Questionnaire (GEQ; Carron, Brawley, & Widmeyer, 2002; Carron, Widmeyer, & Brawley, 1985), which assessed cohesion at both the beginning and end of the season. Overall, the results revealed a significant multivariate effect, Pillai's trace F(12, 438) = 2.68, p = .002. Post hoc analyses showed that at the beginning of the season, athletes from both conditions did not differ in their perceptions of cohesion. However, at the end of the season, athletes in the team goal-setting condition held higher perceptions of cohesion than athletes in the control condition. Overall, the results indicated that team goal setting was an effective team-building tool for influencing cohesiveness in sport teams.

ROCC, a conserved region in cohesin's Mcd1 subunit, is essential for the proper regulation of the maintenance of cohesion and establishment of condensation

PubMed Central

Eng, Thomas; Guacci, Vincent; Koshland, Doug

2014-01-01

Cohesin helps orchestrate higher-order chromosome structure, thereby promoting sister chromatid cohesion, chromosome condensation, DNA repair, and transcriptional regulation. To elucidate how cohesin facilitates these diverse processes, we mutagenized Mcd1p, the kleisin regulatory subunit of budding yeast cohesin. In the linker region of Mcd1p, we identified a novel evolutionarily conserved 10–amino acid cluster, termed the regulation of cohesion and condensation (ROCC) box. We show that ROCC promotes cohesion maintenance by protecting a second activity of cohesin that is distinct from its stable binding to chromosomes. The existence of this second activity is incompatible with the simple embrace mechanism of cohesion. In addition, we show that the ROCC box is required for the establishment of condensation. We provide evidence that ROCC controls cohesion maintenance and condensation establishment through differential functional interactions with Pds5p and Wpl1p. PMID:24966169

School social cohesion, student-school connectedness, and bullying in Colombian adolescents.

PubMed

Springer, Andrew E; Cuevas Jaramillo, Maria Clara; Ortiz Gómez, Yamileth; Case, Katie; Wilkinson, Anna

2016-12-01

Student-school connectedness is inversely associated with multiple health risk behaviors, yet research is limited on the relative contributions of a student's connectedness with school and an overall context of school social cohesion to peer victimization/bullying. We examined associations of perceived school cohesion and student-school connectedness with physical victimization, verbal victimization, and social exclusion in the past six months in adolescents in grades 6-11 (N = 774) attending 11 public and private urban schools in Colombia. Cross-sectional data were collected via a self-administered questionnaire and analyzed using mixed-effects linear regression models. Higher perceived school cohesion was inversely related with exposure to three bullying types examined (p < 0.05); student-school connectedness was negatively related to verbal victimization among girls only (p < 0.01). In full models, school cohesion maintained inverse associations with three bullying types after controlling for student-school connectedness (p ≤ 0.05). Enhancing school cohesion may hold benefits for bullying prevention beyond a student's individual school connectedness. © The Author(s) 2015.

Respect the technique: Status-based respect increases minority group social cohesion with majority groups, while also increasing minority collective action tendencies.

PubMed

Glasford, Demis E; Johnston, Brian

2018-01-01

The present work explores the implications of respect for social change. Social change can be achieved via improved attitudes between minority and majority groups (i.e., social cohesion) or via action taken by minority groups (i.e., collective action). Recent work suggests that the social cohesion route to social change, in particular an emphasis on commonality, may be incompatible with the collective action route to social change. We suggest that social-cohesion strategies rooted in status-based respect may allow for social cohesion and collective action. We experimentally investigated the relative effects of a majority group communicating status-based respect and commonality, as compared to a control, on minority group members' social cohesion with the majority group and willingness to engage in collective action. Status-based respect increased positive attitudes toward a majority group, relative to commonality and control, but was also associated with increased collective action tendencies. Implications for social change are discussed.

Acculturative Stress and Diminishing Family Cohesion Among Recent Latino Immigrants

PubMed Central

De La Rosa, Mario; Ibañez, Gladys E.

2012-01-01

This study investigates a theorized link between Latino immigrants’ experience of acculturative stress during their two initial years in the United States (US) and declines in family cohesion from pre- to post-immigration contexts. This retrospective cohort study included 405 adult participants. Baseline assessment occurred during participants’ first 12 months in the US. Follow-up assessment occurred during participants’ second year in the US. General linear mixed models were used to estimate change in family cohesion and sociocultural correlates of this change. Inverse associations were determined between acculturative stress during initial years in the US and declines in family cohesion from pre-immigration to post-immigration contexts. Participants with undocumented immigration status, those with lower education levels, and those without family in the US generally indicated lower family cohesion. Participants who experienced more acculturative stress and those without family in the US evidenced a greater decline in family cohesion. Results are promising in terms of implications for health services for recent Latino immigrants. PMID:22790880

Mechanical and Hydrologic Effects of Riparian Vegetation on Critical Conditions for Streambank Stability: Upper Truckee River, California

NASA Astrophysics Data System (ADS)

Simon, A.; Pollen, N. L.; Langendoen, E. J.

2005-05-01

The Upper Truckee River is the single largest contributor of sediment to Lake Tahoe with a large proportion of the suspended-sediment load coming from eroding streambanks. Recent advances in quantifying streambank processes highlight the combined effects of hydraulic erosion at the bank toe with geotechnical stability of the upper part of the bank and resulted in the development of a deterministic model of bank-toe erosion and streambank stability (Simon et al., 1999). The use of riparian vegetation in schemes of bank stabilization and stream restoration have become popular but are often implemented on a trial and error basis because of a lack of quantifiable information on the mechanical and hydrologic effects of vegetation on bank stability. This study, conducted along an unstable reach of the Upper Truckee River, combines field data with numerical modeling to quantify (1) hydraulic and geotechnical driving and resisting forces that control bank failures, (2) the mechanical and hydrologic effects of vegetation on shear strength, and (3) the critical conditions for bank stability with and without indigenous riparian species. Tests were conducted using three top-bank treatments: bare (control), Lemmon's willow, and young Lodgepole pine. The susceptibility of the bank toe to erosion by hydraulic forces was quantified by conducting submerged jet tests of in situ material to determine the erodibility coefficient (k) and the critical shear stress of the material. Drained, shear-strength parameters (cohesion and friction angle) of the banks were determined from borehole shear tests at various depths. Pore-water pressure and matric suction were monitored at three depths (30, 100, and 150 cm) with digital tensiometers to calculate changes in apparent cohesion for the period (September 2003 - May 2004) and to differentiate between the hydrologic effects of the two species. Root reinforcement of the two species was quantified by determining the relation between root-tensile strength and root diameter and integrating this with root distribution. Bank failures occurred during winter and spring, brought on by repeated basal melting of snow packs and rain-on-snow events. Lemmon's willow provided an order of magnitude more root-reinforcement (5.5 kPa) than the young Lodgepole pines (0.5 kPa). This difference is not related to differences in root strength, but to the far greater number of roots associated with Lemmon's willow. The hydrologic effects of the species varied spatially and temporally, were beneficial (drier) at depths of 100 and 150 cm but disadvantageous (wetter) near the surface (30 cm). In total, these effects were generally smaller in magnitude than the mechanical effects. Lemmon's willow provided a significant increase in bank strength to streambanks along the Upper Truckee River. Model runs conducted with the hydrologic and mechanical effects of Lemmon's willow included, showed no failures during the simulation period. Overall, Lemmon's willow provided a significant increase in bank strength, reducing the frequency of bank failures and delivery of fine-grained sediment to the study reach of the Upper Truckee River. The use of Lemmon's willow in a bank-stabilization scheme was found to be numerically equivalent to reducing the angle of the entire bank 10-15 degrees.

Sisters Unbound Is Required for Meiotic Centromeric Cohesion in Drosophila melanogaster

PubMed Central

Krishnan, Badri; Thomas, Sharon E.; Yan, Rihui; Yamada, Hirotsugu; Zhulin, Igor B.; McKee, Bruce D.

2014-01-01

Regular meiotic chromosome segregation requires sister centromeres to mono-orient (orient to the same pole) during the first meiotic division (meiosis I) when homologous chromosomes segregate, and to bi-orient (orient to opposite poles) during the second meiotic division (meiosis II) when sister chromatids segregate. Both orientation patterns require cohesion between sister centromeres, which is established during meiotic DNA replication and persists until anaphase of meiosis II. Meiotic cohesion is mediated by a conserved four-protein complex called cohesin that includes two structural maintenance of chromosomes (SMC) subunits (SMC1 and SMC3) and two non-SMC subunits. In Drosophila melanogaster, however, the meiotic cohesion apparatus has not been fully characterized and the non-SMC subunits have not been identified. We have identified a novel Drosophila gene called sisters unbound (sunn), which is required for stable sister chromatid cohesion throughout meiosis. sunn mutations disrupt centromere cohesion during prophase I and cause high frequencies of non-disjunction (NDJ) at both meiotic divisions in both sexes. SUNN co-localizes at centromeres with the cohesion proteins SMC1 and SOLO in both sexes and is necessary for the recruitment of both proteins to centromeres. Although SUNN lacks sequence homology to cohesins, bioinformatic analysis indicates that SUNN may be a structural homolog of the non-SMC cohesin subunit stromalin (SA), suggesting that SUNN may serve as a meiosis-specific cohesin subunit. In conclusion, our data show that SUNN is an essential meiosis-specific Drosophila cohesion protein. PMID:25194162

Effect of Cohesion Uncertainty of Granular Materials on the Kinematics of Scaled Models of Fold-and-Thrust Belts

NASA Astrophysics Data System (ADS)

Nilfouroushan, F.; Pysklywec, R.; Cruden, S.

2009-05-01

Cohesionless or very low cohesion granular materials are widely used in analogue/physical models to simulate brittle rocks in the upper crust. Selection of materials with appropriate cohesion values in such models is important for the simulation of the dynamics of brittle rock deformation in nature. Uncertainties in the magnitude of cohesion (due to measurement errors, extrapolations at low normal stresses, or model setup) in laboratory experiments can possibly result in misinterpretation of the styles and mechanisms of deformation in natural fold-and thrust belts. We ran a series of 2-D numerical models to investigate systematically the effect of cohesion uncertainties on the evolution of models of fold-and-thrust belts. The analyses employ SOPALE, a geodynamic code based on the arbitrary Lagrangian-Eulerian (ALE) finite element method. Similar to analogue models, the material properties of sand and transparent silicone (PDMS) are used to simulate brittle and viscous behaviors of upper crustal rocks. The suite of scaled brittle and brittle-viscous numerical experiments have the same initial geometry but the cohesion value of the brittle layers is increased systematically from 0 to 100 Pa. The stress and strain distribution in different sets of models with different cohesion values are compared and analyzed. The kinematics and geometry of thrust wedges including the location and number of foreland- and hinterland- verging thrust faults, pop-up structures, tapers and topography are also explored and their sensitivity to cohesion value is discussed.

Micromechanical cohesion force between gas hydrate particles measured under high pressure and low temperature conditions.

PubMed

Lee, Bo Ram; Sum, Amadeu K

2015-04-07

To prevent hydrate plugging conditions in the transportation of oil/gas in multiphase flowlines, one of the key processes to control is the agglomeration/deposition of hydrate particles, which are determined by the cohesive/adhesive forces. Previous studies reporting measurements of the cohesive/adhesive force between hydrate particles used cyclopentane hydrate particles in a low-pressure micromechanical force apparatus. In this study, we report the cohesive forces of particles measured in a new high-pressure micromechanical force (MMF) apparatus for ice particles, mixed (methane/ethane, 74.7:25.3) hydrate particles (Structure II), and carbon dioxide hydrate particles (Structure I). The cohesive forces are measured as a function of the contact time, contact force, temperature, and pressure, and determined from pull-off measurements. For the measurements performed of the gas hydrate particles in the gas phase, the determined cohesive force is about 30-35 mN/m, about 8 times higher than the cohesive force of CyC5 hydrates in the liquid CyC5, which is about 4.3 mN/m. We show from our results that the hydrate structure (sI with CO2 hydrates and sII with CH4/C2H6 hydrates) has no influence on the cohesive force. These results are important in the deposition of a gas-dominated system, where the hydrate particles formed in the liquid phase can then stick to the hydrate deposited in the wall exposed to the gas phase.

The Impact of African American Parents’ Racial Discrimination Experiences and Perceived Neighborhood Cohesion on their Racial Socialization Practices

PubMed Central

English, Devin; Busby, Danielle R.; Lambert, Sharon F.; Harrison, Aubrey; Stock, Michelle L.; Gibbons, Frederick X.

2016-01-01

Parental racial socialization is a parenting tool used to prepare African American adolescents for managing racial stressors. While it is known that parents’ racial discrimination experiences affect the racial socialization messages they provide, little is known about the influence of factors that promote supportive and communal parenting, such as perceived neighborhood cohesion. In cohesive neighborhoods, neighbors may help parents address racial discrimination by monitoring youth and conveying racial socialization messages; additionally, the effect of neighborhood cohesion on parents’ racial socialization may differ for boys and girls because parents socialize adolescents about race differently based on expected encounters with racial discrimination. Therefore, the current study examines how parents’ perception of neighborhood cohesion and adolescents’ gender moderate associations between parents’ racial discrimination experiences and the racial socialization messages they deliver to their adolescents. Participants were a community sample of 608 African American adolescents (54 % girls; mean age = 15.5) and their primary caregivers (86 % biological mothers; mean age = 42.0). Structural equation modeling indicated that parental racial discrimination was associated with more promotion of mistrust messages for boys and girls in communities with low neighborhood cohesion. In addition, parental racial discrimination was associated with more cultural socialization messages about racial pride and history for boys in neighborhoods with low neighborhood cohesion. The findings suggest that parents’ racial socialization messages are influenced by their own racial discrimination experiences and the cohesiveness of the neighborhood; furthermore, the content of parental messages delivered varies based on adolescents’ gender. PMID:27189721

Ultimate pier and contraction scour prediction in cohesive soils at selected bridges in Illinois.

DOT National Transportation Integrated Search

2013-09-01

The Scour Rate In COhesive Soils-Erosion Function Apparatus (SRICOS-EFA) method includes an ultimate scour prediction that is : the equilibrium maximum pier and contraction scour of cohesive soils over time. The purpose of this report is to present t...

Community Cohesion: A Report of the Independent Review Team.

ERIC Educational Resources Information Center

Home Office, London (England).

This study examined the views of English citizens and community leaders regarding problems related to disaffected, disadvantaged, culturally diverse groups. The Community Cohesion Review Team (CCRT) investigated issues needing to be addressed to bring about social cohesion. Communities were deeply polarized, with separate educational systems,…

Social Cohesion and Voluntary Associations

ERIC Educational Resources Information Center

Heuser, Brian L.

2005-01-01

Voluntary organizations exert great influence over how social norms and ethical codes are guided into action. As such, they have a significant impact on societal levels of social cohesion. Although social capital involves generalized trust becoming manifest as spontaneous sociability, social cohesion is determined by how that sociability is…

Influence of Sport Education on Group Cohesion in University Physical Education

ERIC Educational Resources Information Center

Jenkins, Jayne M.; Alderman, Brandon L.

2011-01-01

The Sport Education ("SE") curricular model incorporated within university physical education Basic Instruction Program (BIP) may increase group cohesion. This study's purpose was to identify student perceptions of a BIP course taught within "SE," and investigate group cohesion in differing activity content. Participants…

Tree-root control of shallow landslides

NASA Astrophysics Data System (ADS)

Cohen, Denis; Schwarz, Massimiliano

2017-08-01

Tree roots have long been recognized to increase slope stability by reinforcing the strength of soils. Slope stability models usually include the effects of roots by adding an apparent cohesion to the soil to simulate root strength. No model includes the combined effects of root distribution heterogeneity, stress-strain behavior of root reinforcement, or root strength in compression. Recent field observations, however, indicate that shallow landslide triggering mechanisms are characterized by differential deformation that indicates localized activation of zones in tension, compression, and shear in the soil. Here we describe a new model for slope stability that specifically considers these effects. The model is a strain-step discrete element model that reproduces the self-organized redistribution of forces on a slope during rainfall-triggered shallow landslides. We use a conceptual sigmoidal-shaped hillslope with a clearing in its center to explore the effects of tree size, spacing, weak zones, maximum root-size diameter, and different root strength configurations. Simulation results indicate that tree roots can stabilize slopes that would otherwise fail without them and, in general, higher root density with higher root reinforcement results in a more stable slope. The variation in root stiffness with diameter can, in some cases, invert this relationship. Root tension provides more resistance to failure than root compression but roots with both tension and compression offer the best resistance to failure. Lateral (slope-parallel) tension can be important in cases when the magnitude of this force is comparable to the slope-perpendicular tensile force. In this case, lateral forces can bring to failure tree-covered areas with high root reinforcement. Slope failure occurs when downslope soil compression reaches the soil maximum strength. When this occurs depends on the amount of root tension upslope in both the slope-perpendicular and slope-parallel directions. Roots in tension can prevent failure by reducing soil compressive forces downslope. When root reinforcement is limited, a crack parallel to the slope forms near the top of the hillslope. Simulations with roots that fail across this crack always resulted in a landslide. Slopes that did not form a crack could either fail or remain stable, depending on root reinforcement. Tree spacing is important for the location of weak zones but tree location on the slope (with respect to where a crack opens) is as important. Finally, for the specific cases tested here, intermediate-sized roots (5 to 20 mm in diameter) appear to contribute most to root reinforcement. Our results show more complex behaviors than can be obtained with the traditional slope-uniform, apparent-cohesion approach. A full understanding of the mechanisms of shallow landslide triggering requires a complete re-evaluation of this traditional approach that cannot predict where and how forces are mobilized and distributed in roots and soils, and how these control shallow landslides shape, size, location, and timing.

Effects of Particle Size on the Shear Behavior of Coarse Grained Soils Reinforced with Geogrid.

PubMed

Kim, Daehyeon; Ha, Sungwoo

2014-02-07

In order to design civil structures that are supported by soils, the shear strength parameters of soils are required. Due to the large particle size of coarse-grained soils, large direct shear tests should be performed. In this study, large direct shear tests on three types of coarse grained soils (4.5 mm, 7.9 mm, and 15.9 mm) were performed to evaluate the effects of particle size on the shear behavior of coarse grained soils with/without geogrid reinforcements. Based on the direct shear test results, it was found that, in the case of no-reinforcement, the larger the maximum particle size became, the larger the friction angle was. Compared with the no-reinforcement case, the cases reinforced with either soft geogrid or stiff geogrid have smaller friction angles. The cohesion of the soil reinforced with stiff geogrid was larger than that of the soil reinforced with soft geogrid. The difference in the shear strength occurs because the case with a stiff geogrid has more soil to geogrid contact area, leading to the reduction in interlocking between soil particles.

Correlation between the band gap expansion and melting temperature depression of nanostructured semiconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Jianwei, E-mail: jwl189@163.com; Zhao, Xinsheng; Liu, Xinjuan

The band gap and melting temperature of a semiconductor are tunable with the size and shape of the specimen at the nanometer scale, and related mechanisms remain as yet unclear. In order to understand the common origin of the size and shape effect on these two seemingly irrelevant properties, we clarify, correlate, formulate, and quantify these two properties of GaAs, GaN, InP, and InN nanocrystals from the perspectives of bond order-length-strength correlation using the core-shell configuration. The consistency in the theoretical predictions, experimental observations, and numerical calculations verify that the broken-bond-induced local bond contraction and strength gain dictates the bandmore » gap expansion, while the atomic cohesive energy loss due to bond number reduction depresses the melting point. The fraction of the under-coordinated atoms in the skin shell quantitatively determines the shape and size dependency. The atomic under-coordination in the skin down to a depth of two atomic layers inducing a change in the local chemical bond is the common physical origin.« less

Natural Tissue Microenvironmental Conditions Modulate Adhesive Material Performance

PubMed Central

Oliva, Nuria; Shitreet, Sagi; Abraham, Eytan; Stanley, Butch; Edelman, Elazer R.; Artzi, Natalie

2015-01-01

We designed and optimized tissue-responsive adhesive materials by matching material and tissue properties. A two-component material based on dextran aldehyde and dendrimer amine provides a cohesive gel through aldehyde–amine cross-linking and an adhesive interface created by a dextran aldehyde-selective reaction with tissue amines. By altering aldehyde–amine chemistry, we examined how variations in tissue surfaces (serosal amine density in the duodenum, jejunum, and ileum) affect interactions with adhesive materials of varied compositions (aldehyde content). Interestingly, the same adhesive formulation reacts differentially with the three regions of the small intestine as a result of variation in the tissue amine density along the intestinal tract, affecting the tissue–material interfacial morphology, adhesion strength, and adhesive mechanical properties. Whereas tissues provide chemical anchors for interaction with materials, we were able to tune the adhesion strength for each section of the small intestine tissue by altering the adhesive formulation using a two-component material with flexible variables aimed at controlling the aldehyde/amine ratio. This tissue-specific approach should be applied to the broad spectrum of biomaterials, taking into account specific microenvironmental conditions in material design. PMID:23046479

Rheology and adhesion of poly(acrylic acid)/laponite nanocomposite hydrogels as biocompatible adhesives.

PubMed

Shen, Muxian; Li, Li; Sun, Yimin; Xu, Jun; Guo, Xuhong; Prud'homme, Robert K

2014-02-18

Biocompatible nanocomposite hydrogels (NC gels) consisting of poly(acrylic acid) (PAA) and nanosized clay (Laponite) were successfully synthesized by in situ free-radical polymerization of acrylic acid (AA) in aqueous solutions of Laponite. The obtained NC gels were uniform and transparent. Their viscosity, storage modulus G', and loss modulus G″ increased significantly upon increasing the content of Laponite and the dose of AA, while exhibiting a maximum with increasing the neutralization degree of AA. They showed tunable adhesion by changing the dose of Laponite and monomer as well as the neutralization degree of AA, as determined by 180° peel strength measurement. The maximal adhesion was shown when reaching a balance between cohesion and fluidity. A homemade Johnson-Kendall-Roberts (JKR) instrument was employed to study the surface adhesion behavior of the NC gels. The combination of peel strength, rheology, and JKR measurements offers the opportunity of insight into the mechanism of adhesion of hydrogels. The NC gels with tunable adhesion should be ideal candidates for dental adhesive, wound dressing, and tissue engineering.

3D Progressive Damage Modeling for Laminated Composite Based on Crack Band Theory and Continuum Damage Mechanics

NASA Technical Reports Server (NTRS)

Wang, John T.; Pineda, Evan J.; Ranatunga, Vipul; Smeltzer, Stanley S.

2015-01-01

A simple continuum damage mechanics (CDM) based 3D progressive damage analysis (PDA) tool for laminated composites was developed and implemented as a user defined material subroutine to link with a commercially available explicit finite element code. This PDA tool uses linear lamina properties from standard tests, predicts damage initiation with an easy-to-implement Hashin-Rotem failure criteria, and in the damage evolution phase, evaluates the degradation of material properties based on the crack band theory and traction-separation cohesive laws. It follows Matzenmiller et al.'s formulation to incorporate the degrading material properties into the damaged stiffness matrix. Since nonlinear shear and matrix stress-strain relations are not implemented, correction factors are used for slowing the reduction of the damaged shear stiffness terms to reflect the effect of these nonlinearities on the laminate strength predictions. This CDM based PDA tool is implemented as a user defined material (VUMAT) to link with the Abaqus/Explicit code. Strength predictions obtained, using this VUMAT, are correlated with test data for a set of notched specimens under tension and compression loads.

The Strength of a Loosely Defined Movement: Eugenics and Medicine in Imperial Russia

PubMed Central

Krementsov, Nikolai

2015-01-01

This essay examines the ‘infiltration’ of eugenics into Russian medical discourse during the formation of the eugenics movement in western Europe and North America in 1900–17. It describes the efforts of two Russian physicians, the bacteriologist and hygienist Nikolai Gamaleia (1859–1949) and the psychiatrist Tikhon Iudin (1879–1949), to introduce eugenics to the Russian medical community, analysing in detail what attracted these representatives of two different medical specialties to eugenic ideas, ideals, and policies advocated by their western colleagues. On the basis of a close examination of the similarities and differences in Gamaleia’s and Iudin’s attitudes to eugenics, the essay argues that lack of cohesiveness gave the early eugenics movement a unique strength. The loose mix of widely varying ideas, ideals, methods, policies, activities and proposals covered by the umbrella of eugenics offered to a variety of educated professionals in Russia and elsewhere the possibility of choosing, adopting and adapting particular elements to their own national, professional, institutional and disciplinary contexts, interests and agendas. PMID:25498435

Effect of Poly(Vinyl Alcohol) Addition on the Properties of Hydrothermal Derived Calcium Phosphate Cement for Bone Filling Materials

NASA Astrophysics Data System (ADS)

Razali, N. N.; Sopyan, I.; Mel, M.; Salleh, H. M.; Rahman, M. M.; Singh, R.

2017-06-01

The effect of addition of poly(vinyl alcohol) on hydrothermal derived calcium phosphate cement has been studied. The precursors used to prepare the cement were calcium oxide (CaO) and ammonium dihydrogen phosphate (NH4H2PO4); the reaction was conducted in water at 80-100°C. To improve properties of CPC, poly(vinyl alcohol) (PVA) of 1wt% and 2wt% was added to the liquid phase of CPC and the results were compared to CPC without PVA addition. The addition of PVA was proved to bring remarkable effects on cohesion, setting time and mechanical strength of CPC which make it suitable physically for injectable bone filler applications.

Development and Testing of a Device Capable of Placing Model Piles by Driving and Pushing in the Centrifuge

DTIC Science & Technology

1989-05-01

Cohesion C M /LT 2 5 , D ynamic Time T T 5 "I Wave Speed P L/T7 IT Yield Strength F I/LT2 a I9 i spl acement D L 9 It Area A L2 10 T Permeability K L/T 11...by the square of the dynamic time scale factor (1/n), or I/n2 . The two scaling laws derived are summarized below. The subscripts m and p designate the...4-1(b) depicts the model pile groups and test gravity levels. InUd ~ cial’odel Piles a~ft -to Ri ght--49.3, 5.,3. ana g o d ’iaeIs~ M )uodel Pile

The comparative effectiveness of a team-based versus group-based physical activity intervention for cancer survivors.

PubMed

Carter, Cindy L; Onicescu, Georgiana; Cartmell, Kathleen B; Sterba, Katherine R; Tomsic, James; Alberg, Anthony J

2012-08-01

Physical activity benefits cancer survivors, but the comparative effectiveness of a team-based delivery approach remains unexplored. The hypothesis tested was that a team-based physical activity intervention delivery approach has added physical and psychological benefits compared to a group-based approach. A team-based sport accessible to survivors is dragon boating, which requires no previous experience and allows for diverse skill levels. In a non-randomized trial, cancer survivors chose between two similarly structured 8-week programs, a dragon boat paddling team (n = 68) or group-based walking program (n = 52). Three separate intervention rounds were carried out in 2007-2008. Pre-post testing measured physical and psychosocial outcomes. Compared to walkers, paddlers had significantly greater (all p < 0.01) team cohesion, program adherence/attendance, and increased upper-body strength. For quality-of-life outcomes, both interventions were associated with pre-post improvements, but with no clear-cut pattern of between-intervention differences. These hypothesis-generating findings suggest that a short-term, team-based physical activity program (dragon boat paddling) was associated with increased cohesion and adherence/attendance. Improvements in physical fitness and psychosocial benefits were comparable to a traditional, group-based walking program. Compared to a group-based intervention delivery format, the team-based intervention delivery format holds promise for promoting physical activity program adherence/attendance in cancer survivors.

How predation shapes the social interaction rules of shoaling fish.

PubMed

Herbert-Read, James E; Rosén, Emil; Szorkovszky, Alex; Ioannou, Christos C; Rogell, Björn; Perna, Andrea; Ramnarine, Indar W; Kotrschal, Alexander; Kolm, Niclas; Krause, Jens; Sumpter, David J T

2017-08-30

Predation is thought to shape the macroscopic properties of animal groups, making moving groups more cohesive and coordinated. Precisely how predation has shaped individuals' fine-scale social interactions in natural populations, however, is unknown. Using high-resolution tracking data of shoaling fish ( Poecilia reticulata ) from populations differing in natural predation pressure, we show how predation adapts individuals' social interaction rules. Fish originating from high predation environments formed larger, more cohesive, but not more polarized groups than fish from low predation environments. Using a new approach to detect the discrete points in time when individuals decide to update their movements based on the available social cues, we determine how these collective properties emerge from individuals' microscopic social interactions. We first confirm predictions that predation shapes the attraction-repulsion dynamic of these fish, reducing the critical distance at which neighbours move apart, or come back together. While we find strong evidence that fish align with their near neighbours, we do not find that predation shapes the strength or likelihood of these alignment tendencies. We also find that predation sharpens individuals' acceleration and deceleration responses, implying key perceptual and energetic differences associated with how individuals move in different predation regimes. Our results reveal how predation can shape the social interactions of individuals in groups, ultimately driving differences in groups' collective behaviour. © 2017 The Authors.

Group Cohesiveness in the Industrial Work Group.

ERIC Educational Resources Information Center

Seashore, Stanley E.

Originally published in 1954, this investigation was designed to explore the formation of cohesiveness within work groups in an industrial setting, and the relationship of cohesiveness to productivity and to group members' mental health and adjustment. A company wide questionnaire survey, involving 228 groups totaling 5,871 workers, was made of…

A Reappraisal of Lexical Cohesion in Conversational Discourse

ERIC Educational Resources Information Center

Gomez Gonzalez, Maria De Los Angeles

2013-01-01

Cohesion, or the connectedness of discourse, has been recognized as playing a crucial role in both language production and comprehension processes. Researchers have debated about the "right" number and classification of cohesive devices, as well as about their interaction with coherence and/or genre. The present study proposes an integrative model…

Cohesion and Coherence in Theory and Reading Research.

ERIC Educational Resources Information Center

Fulcher, Glenn

1989-01-01

Examines the conflict between applied linguistics and schema theoreticians over the relationship between the concepts of cohesion and coherence. Suggests that the positions taken are the result of theoretically different starting points. Reports the results of two studies that support the theory accounting for cohesion and coherence. (RS)

Cohesion Features in ESL Reading: Comparing Beginning, Intermediate and Advanced Textbooks

ERIC Educational Resources Information Center

Plakans, Lia; Bilki, Zeynep

2016-01-01

This study of English as a second language (ESL) reading textbooks investigates cohesion in reading passages from 27 textbooks. The guiding research questions were whether and how cohesion differs across textbooks written for beginning, intermediate, and advanced second language readers. Using a computational tool called Coh-Metrix, textual…