Lipid composition and lidocaine effect on immediate and delayed injection pain following propofol administration.

PubMed

Zirak, Nahid; Bameshki, Alireza; Yazdani, Mohammadjavad; Gilani, Mehryar Taghavi

2016-01-01

Propofol has been used for the induction and maintenance of anesthesia. However, patients experience vascular pain during its injection. The objective of this study was to compare the effect of the lipid type used in propofol preparations and that of lidocaine on the immediate and delayed vascular pain induced by propofol administration. In this double-blinded clinical study, 150 patients at American Society of Anesthesiologists level I-II were randomly divided into three equally sized groups. A propofol with medium and long-chain triglycerides (propofol-MCT/LCT) was administered to the first group. The second group received propofol containing propofol-LCT, and the third group received propofol-LCT and pretreatment lidocaine 20 mg. The incidence and the intensity of immediate (during injection) and delayed injection pain (after 20 s) were evaluated on a verbal analog scale (1-10) until patients' unconsciousness. Sample size was calculated with SigmaPlot version 12.5 software. Data were analyzed with Statistical Package for the Social Sciences (SPSS) version 16, one-way analysis of variance, and post-hoc Tukey. P < 0.05 was considered statistically significant. The demographic parameters of the three groups were similar. The lidocaine group experienced the least immediate vascular pain. The intensity of pain was highest in the propofol-LCT group (P = 0.04). Additionally, the intensity of delayed pain was lowest in the propofol-MCT/LCT group (P = 0.01). The incidence of pain associated with the propofol administration was 26.5, 44, and 18%, respectively, in propofol-MCT/LCT, propofol-LCT, and lidocaine and propofol-LCT groups. The results indicate an effect of the lipid type on delayed pain reduction, especially propofol-MCT/LCT. On the other hand, the lidocaine decreases immediate propofol-LCT vascular pain.

Estrogenic activity of lambda-cyhalothrin in the MCF-7 human breast carcinoma cell line.

PubMed

Zhao, Meirong; Zhang, Ying; Liu, Weiping; Xu, Chao; Wang, Lumei; Gan, Jianying

2008-05-01

Synthetic pyrethroids are widely used in both agricultural and urban environments for insect control. Lambda-cyhalothrin (LCT) is one of the most common pyrethroids and is used mainly for controlling mosquitoes, fleas, cockroaches, flies, and ants around households. Previous studies have addressed the environmental behaviors and acute toxicities of LCT, but little is known about its chronic toxicity, such as estrogen-like activity. In the present study, the estrogenic potential of LCT was evaluated using the MCF-7 human breast carcinoma cell line. The in vitro E-screen assay showed that 10(-7) M LCT could significantly promote MCF-7 cell proliferation, with a relative proliferative effect ratio of 45%. The cell proliferation induced by LCT could be blocked completely, however, by the addition of 10(-9) M of the estrogen receptor (ER)-antagonist ICI 182,780. The semiquantitative reverse transcription-polymerase chain reaction (RT-PCR) results showed that the Trefoil factor 1 (pS2) and progesterone receptor gene expression were up-regulated by 10(-7) M LCT for 2- and 1.5-fold, respectively. On the other hand, RT-PCR, Western blot analysis, and immunofluorescent assay demonstrated that LCT significantly repressed the mRNA and protein expression levels of ERalpha and ERbeta. These observations indicate that LCT possesses estrogenic properties and may function as a xenoestrogen, likely via a mechanism similar to that of 17beta-estradiol. The endocrine-disruption potential of LCT should be considered when assessing the safety of this compound in sensitive environmental compartments.

Medium-chain, triglyceride-containing lipid emulsions increase human neutrophil beta2 integrin expression, adhesion, and degranulation.

PubMed

Wanten, G J; Geijtenbeek, T B; Raymakers, R A; van Kooyk, Y; Roos, D; Jansen, J B; Naber, A H

2000-01-01

To test the hypothesis that lipid emulsions with different triglyceride structures have distinct immunomodulatory properties, we analyzed human neutrophil adhesion and degranulation after lipid incubation. Neutrophils, isolated from the blood of 10 healthy volunteers, were incubated in medium or physiologic (2.5 mmol/L) emulsions containing long-chain (LCT), medium-chain (MCT), mixed LCT/MCT, or structured (SL) triglycerides. Expression of adhesion molecules and degranulation markers was evaluated by flow cytometry. Also, functional adhesion was investigated by means of a flow cytometric assay using fluorescent beads coated with the integrin ligand intercellular adhesion molecule (ICAM)-1. Although LCT and SL had no effect, LCT/MCT significantly increased expression of the beta2 integrins lymphocyte-function-associated antigen 1 (+18%), macrophage antigen 1 (+387%), p150,95 (+82%), and (alphaDbeta2 (+230%). Degranulation marker expression for azurophilic (CD63, +210%) and specific granules (CD66b, +370%) also significantly increased, whereas L-selectin (CD62L, -70%) decreased. The effects of LCT/MCT were mimicked by the MCT emulsion. ICAM-1 adhesion (% beads bound) was increased by LCT/MCT (34% +/- 4%), whereas LCT (19% +/-3%) and SL (20% +/- 2%) had no effect compared with medium (17% +/- 3%). LCT/MCT and MCT, contrary to LCT and SL emulsions, increased neutrophil beta2 integrin expression, adhesion, and degranulation. Apart from other emulsion constituents, triglyceride chain length might therefore be a key feature in the interaction of lipid emulsions and the phagocyte immune system.

Olive Oil-Based Lipid Emulsions Do Not Influence Platelet Receptor Expression in Comparison to Medium and Long Chain Triglycerides In vitro.

PubMed

Stoetzer, Carsten; Nickel, Katja; Weißig, Annette; Großheim, Marieke; Scheinichen, Dirk; Doll, Thorben; Jüttner, Björn

2016-11-01

Lipid emulsions influence platelet aggregation and receptor expression. However, the effect on platelet function is not fully explained. Therefore, the aim of this study was to examine the influence of the lipids Lipofundin ® , Lipidem ® and ClinOleic ® on surface expressions of P-selectin, GPIb and GPIIb/IIIa on platelets in vitro. Whole blood was incubated in two different concentrations (0.06 and 0.6 mg/ml) of LCT/MCT, n-3/LCT/MCT and LCT-MUFA for 30 min, followed by activation with TRAP-6 or ADP for flow-cytometric assay. Rates of P-selectin, GPIb and GPIIb/IIIa expression were analyzed. There was a significant increase in GPIIb/IIIa- and P-selectin-expression after incubation with LCT/MCT and n-3/LCT/MCT at the concentration of 0.6 mg/ml, without and after stimulation with TRAP-6 and ADP. GPIb was significantly decreased. Accordingly, LCT-MUFA had no effect on receptor expression of platelets in vitro. We demonstrated that LCT-MUFA did not activate receptor expression of platelets whereas LCT/MCT significantly increased platelet aggregation in vitro. This finding should be noted for parenteral nutrition of intensive care patients and, in the future, might provide further insight into the pathogenic pathways of acute thromboembolic events. However, prospectively designed clinical studies are needed to support our results.

Medium-chain triglycerides/long-chain triglycerides versus long-chain triglycerides in treatment of cancer patients with major body mass loss. Survival in patients with refractory cachexia.

PubMed

Szefel, Jarosław; Kruszewski, Wiesław J; Szajewski, Mariusz; Ciesielski, Maciej; Sobczak, Ewa; Czerepko, Maksymilian; Łysiak-Szydłowska, Wiesława

2016-01-01

Currently there are no established guidelines regarding the use of long-chain triglycerides (LCT) vs. medium-chain triglycerides medium-chain triglycerides (MCT)/long-chain triglycerides (LCT) in total parenteral nutrition (TPN). Severe malnutrition of patients with refractory cachexia (RC) often causes their disqualification from invasive methods of treatment thus decreasing their quality of life and survival time. To compare the changes in nutritional state of patients with RC receiving PN with LCT and LCT/MCT lipid emulsions and to assess the influence of enteral nutrition on their survival time. The study group comprised of 50 patients (23 female, 27 male) with a median age of 66 years. Refractory cachexia was diagnosed in them due to dysphagia secondary to solid tumours causing obstruction of the gastrointestinal tract (GT). All patients were qualified for surgical gastrostomy due to contraindications to percutaneous endoscopic gastrostomy. The patients were randomly assigned into one of two groups and perioperatively received either LCT or LCT/MCT. Blood samples were collected four times and tested for: total protein, albumin, prealbumin, and C-reactive protein concentration. Patients received Home Enteral Nutrition after discharge from hospital. Changes in nutritional status parameters were similar among patients receiving lipid emulsions LCT vs. MCT/LCT in TPN for 11 days. The mean survival time of all patients operated to gain enteral access to nutrition was 192 ±268 days, and the median survival was 98 days. Regarding the short-term TPN, the results of the study do not demonstrate any superiority of MCT/LCT lipid emulsions over LCT, or vice versa. The inability to eat significantly accelerates unintended body mass loss among patients with RC. Disqualification from invasive treatment options deprives some patients of the benefits they might have obtained from the surgical access to GT and enteral nutrition.

Lambda-cyhalothrin disrupts the up-regulation effect of 17β-estradiol on post-synaptic density 95 protein expression via estrogen receptor α-dependent Akt pathway.

PubMed

Wang, Qunan; Xia, Xin; Deng, Xiaomei; Li, Nian; Wu, Daji; Zhang, Long; Yang, Chengwei; Tao, Fangbiao; Zhou, Jiangning

2016-03-01

Lambda-cyhalothrin (LCT), one of the type II pyrethroids, has been widely used throughout the world. The estrogenic effect of LCT to increase cell proliferation has been well established. However, whether the estrogenic effect of LCT will influence neurodevelopment has not been investigated. In addition, 17β-Estradiol (E2) plays a crucial role in neurodevelopment and induces an increase in synaptic proteins. The post-synaptic density 95 (PSD95) protein, which is involved in the development of the structure and function of new spines and localized with estrogen receptor α (ERα) at the post-synaptic density (PSD), was detected in our study by using hippocampal neuron cell line HT22. We found that LCT up-regulated PSD95 and ERα expression, estrogen receptor (ER) antagonist ICI182,780 and phosphatidylinositol-4; 5-bisphosphate 3-kinase (PI3K) inhibitor LY294,002 blocked this effect. In addition, LCT disrupted the promotion effect of E2 on PSD95. To investigate whether the observed changes are caused by ERα-dependent signaling activation, we next detected the effects of LCT on the ERα-mediated PI3K-Protein kinase B (PKB/Akt)-eukaryotic initiation factor (eIF) 4E-binding protein 1 (4E-BP1) pathway. There existed an activation of Akt and the downstream factor 4E-BP1 after LCT treatment. In addition, LCT could disrupt the activation effect of E2 on the Akt pathway. However, no changes in cAMP response element-binding protein (CREB) activation and PSD95 messenger ribonucleic acid (mRNA) were observed. Our findings demonstrated that LCT could increase the PSD95 protein level via the ERα-dependent Akt pathway, and LCT might disrupt the up-regulation effect of E2 on PSD95 protein expression via this signaling pathway. Copyright © 2015. Published by Elsevier B.V.

Medium-chain triglycerides/long-chain triglycerides versus long-chain triglycerides in treatment of cancer patients with major body mass loss. Survival in patients with refractory cachexia

PubMed Central

Kruszewski, Wiesław J.; Szajewski, Mariusz; Ciesielski, Maciej; Sobczak, Ewa; Czerepko, Maksymilian; Łysiak-Szydłowska, Wiesława

2016-01-01

Introduction Currently there are no established guidelines regarding the use of long-chain triglycerides (LCT) vs. medium-chain triglycerides medium-chain triglycerides (MCT)/long-chain triglycerides (LCT) in total parenteral nutrition (TPN). Severe malnutrition of patients with refractory cachexia (RC) often causes their disqualification from invasive methods of treatment thus decreasing their quality of life and survival time. Aim To compare the changes in nutritional state of patients with RC receiving PN with LCT and LCT/MCT lipid emulsions and to assess the influence of enteral nutrition on their survival time. Material and methods The study group comprised of 50 patients (23 female, 27 male) with a median age of 66 years. Refractory cachexia was diagnosed in them due to dysphagia secondary to solid tumours causing obstruction of the gastrointestinal tract (GT). All patients were qualified for surgical gastrostomy due to contraindications to percutaneous endoscopic gastrostomy. The patients were randomly assigned into one of two groups and perioperatively received either LCT or LCT/MCT. Blood samples were collected four times and tested for: total protein, albumin, prealbumin, and C-reactive protein concentration. Patients received Home Enteral Nutrition after discharge from hospital. Results Changes in nutritional status parameters were similar among patients receiving lipid emulsions LCT vs. MCT/LCT in TPN for 11 days. The mean survival time of all patients operated to gain enteral access to nutrition was 192 ±268 days, and the median survival was 98 days. Conclusions Regarding the short-term TPN, the results of the study do not demonstrate any superiority of MCT/LCT lipid emulsions over LCT, or vice versa. The inability to eat significantly accelerates unintended body mass loss among patients with RC. Disqualification from invasive treatment options deprives some patients of the benefits they might have obtained from the surgical access to GT and enteral nutrition. PMID:27713780

Lipid composition and lidocaine effect on immediate and delayed injection pain following propofol administration

PubMed Central

Zirak, Nahid; Bameshki, Alireza; Yazdani, Mohammadjavad; Gilani, Mehryar Taghavi

2016-01-01

Background: Propofol has been used for the induction and maintenance of anesthesia. However, patients experience vascular pain during its injection. Aims: The objective of this study was to compare the effect of the lipid type used in propofol preparations and that of lidocaine on the immediate and delayed vascular pain induced by propofol administration. Materials and Methods: In this double-blinded clinical study, 150 patients at American Society of Anesthesiologists level I-II were randomly divided into three equally sized groups. A propofol with medium and long-chain triglycerides (propofol-MCT/LCT) was administered to the first group. The second group received propofol containing propofol-LCT, and the third group received propofol-LCT and pretreatment lidocaine 20 mg. The incidence and the intensity of immediate (during injection) and delayed injection pain (after 20 s) were evaluated on a verbal analog scale (1–10) until patients’ unconsciousness. Statistical Analysis: Sample size was calculated with SigmaPlot version 12.5 software. Data were analyzed with Statistical Package for the Social Sciences (SPSS) version 16, one-way analysis of variance, and post-hoc Tukey. P < 0.05 was considered statistically significant. Results: The demographic parameters of the three groups were similar. The lidocaine group experienced the least immediate vascular pain. The intensity of pain was highest in the propofol-LCT group (P = 0.04). Additionally, the intensity of delayed pain was lowest in the propofol-MCT/LCT group (P = 0.01). The incidence of pain associated with the propofol administration was 26.5, 44, and 18%, respectively, in propofol-MCT/LCT, propofol-LCT, and lidocaine and propofol-LCT groups. Conclusion: The results indicate an effect of the lipid type on delayed pain reduction, especially propofol-MCT/LCT. On the other hand, the lidocaine decreases immediate propofol-LCT vascular pain. PMID:26957686

Concordant ages for the Lava Creek Tuff from high-spatial-resolution U-Pb dating of zircon rim faces and single-crystal sanidine 40Ar/39Ar dating

NASA Astrophysics Data System (ADS)

Matthews, N. E.; Vazquez, J. A.; Calvert, A. T.

2013-12-01

The last great explosive supereruption from the Yellowstone Plateau formed present-day Yellowstone caldera and ejected the >1000 km3 of rhyolite that composes the Lava Creek Tuff (LCT). The LCT eruption blanketed much of the western United States in ash, and consequently is a key chronostratigraphic marker bed for delimiting Quaternary uplift rates, the age of middle Pleistocene glacial and pluvial deposits, and tephra correlation in North America. Previous 40Ar/39Ar dating of the two mineralogically distinct LCT members (A & B) yield ages ranging from ca. 600 ka (Gansecki et al., 1998) to ca. 640 ka (Lanphere et al., 2002). To resolve the timing of eruption and crystallization timescale for the LCT magma, we dated both LCT members using a dual-method approach as follows: (1) ion microprobe (SHRIMP-RG) U-Pb dating and trace-element characterization of the final few micrometers of zircon crystallization by analysis of unpolished rims on indium-mounted crystals, and dating of the onset of zircon crystallization by traditional analysis of sectioned crystal interiors, and (2) laser-fusion 40Ar/39Ar dating of single sanidine crystals from bulk LCT ignimbrite and pumice. The unpolished rims of zircon from LCT members A & B yield indistinguishable ages, with a mean age of 621.8 × 2.5 ka (1σ) after correction for initial 230Th disequilibrium as constrained by ion-probe analyses of LCT melt inclusions. Single sanidine crystals from LCT-B yield a mean age of 624.9 × 2.6 ka (FCT=28.17 Ma) that is indistinguishable from the zircon rim ages for both members. These results indicate that LCT members A & B erupted over a geologically brief interval, which is supported by the direct and gradational contact of their equivalent fallout in distal lacustrine deposits and a lack of field evidence for a significant time-break between the LCT A & B in proximal deposits (Christiansen, 2001), but contrasts with older Yellowstone ignimbrite (e.g., Huckleberry Ridge) that may have erupted as multiple pulses over tens of kyr (Ellis et al., 2012). Both LCT members contain zircon whose interiors yield U-Pb ages that are mostly ca. 40 kyr older than their rims, suggesting a short timescale for assembly of the LCT magma chamber relative to some other voluminous bodies of silicic magma (e.g., Fish Canyon). Trace-element concentrations in zircon from Members A and B appear diagnostic, with the former containing higher U and REE concentrations. Our concordant results from U-Pb and 40Ar/39Ar dating indicating a ca. 625 ka age for the LCT eruption are supported by the stratigraphic position of LCT-B tephra at or near the top of Great Basin pluvial lake bed sequences associated with Marine Isotope Stage 16, whose termination is astronomically dated at 621 ka. Christiansen, 2001, USGS Prof. Pap. 729-G; Ellis et al., 2012, Quat Geochron 9: 31-41; Gansecki et al., 1998, Geology 26(4): 343-346; Lanphere et al., 2002, GSA Bull. 114(5): 559-568.

The protective effect of royal jelly on chronic lambda-cyhalothrin toxicity: serum biochemical parameters, lipid peroxidation, and genotoxic and histopathological alterations in swiss albino mice.

PubMed

Cavuşoğlu, Kültiğin; Yapar, Kürşad; Oruç, Ertan; Yalçın, Emine

2011-10-01

The present study was undertaken to investigate the protective effect of royal jelly (RJ) against toxicity induced by a synthetic pyrethroid insecticide, lambda-cyhalothrin (LCT), in Swiss albino mice. Animals were randomly divided into six groups of six animals each. The control group received distilled water alone, whereas mice in the treatment groups received RJ alone (100 or 250 mg/kg of body weight), LCT alone (668 ppm), or RJ+LCT for 21 days. All mice (100%) survived until the end of experiment and were sacrificed at the end of 24 hours. Blood, bone marrow, and liver and kidney tissues were analyzed for aspartate aminotransferase (AST), alanine aminotransferase (ALT), blood urea nitrogen (BUN), creatinine, malondialdehyde (MDA), and reduced glutathione (GSH) levels and micronucleus (MN) frequency, chromosomal aberrations (CAs), and pathological damages. Serum AST, ALT, BUN, and creatinine levels were elevated in mice treated with LCT alone compared with the other tested groups (P<.05). LCT-induced oxidative damage caused a significant decrease in GSH levels and a significant rise in MDA levels of liver and kidney tissues. LCT alone-treated mice presented higher frequencies (P<.05) of MNs, CAs, and abnormal metaphases compared with the controls; moreover, the mitotic index was lower than in controls (P<.05). Oral treatment with RJ significantly ameliorated the indices of hepatotoxicity, nephrotoxicity, lipid peroxidation, and genotoxicity induced by LCT. Both doses of RJ tested provided significant protection against LCT-induced toxicity, and its strongest effect was observed at the dose level of 250 mg/kg of body weight. In vivo results suggest that RJ is a potent antioxidant against LCT-induced toxicity, and its protective effect is dose dependent.

Lattice cluster theory of associating polymers. I. Solutions of linear telechelic polymer chains.

PubMed

Dudowicz, Jacek; Freed, Karl F

2012-02-14

The lattice cluster theory (LCT) for the thermodynamics of a wide array of polymer systems has been developed by using an analogy to Mayer's virial expansions for non-ideal gases. However, the high-temperature expansion inherent to the LCT has heretofore precluded its application to systems exhibiting strong, specific "sticky" interactions. The present paper describes a reformulation of the LCT necessary to treat systems with both weak and strong, "sticky" interactions. This initial study concerns solutions of linear telechelic chains (with stickers at the chain ends) as the self-assembling system. The main idea behind this extension of the LCT lies in the extraction of terms associated with the strong interactions from the cluster expansion. The generalized LCT for sticky systems reduces to the quasi-chemical theory of hydrogen bonding of Panyioutou and Sanchez when correlation corrections are neglected in the LCT. A diagrammatic representation is employed to facilitate the evaluation of the corrections to the zeroth-order approximation from short range correlations. © 2012 American Institute of Physics

Brain cholinergic alterations in rats subjected to repeated immobilization or forced swim stress on lambda-cyhalothrin exposure.

PubMed

Shukla, Rajendra K; Gupta, Richa; Srivastava, Pranay; Dhuriya, Yogesh K; Singh, Anshuman; Chandravanshi, Lalit P; Kumar, Ajay; Siddiqui, M Haris; Parmar, Devendra; Pant, Aditya B; Khanna, Vinay K

2016-02-01

Role of immobilization stress (IMS), a psychological stressor and forced swim stress (FSS), a physical stressor was investigated on the neurobehavioral toxicity of lambda-cyhalothrin (LCT), a new generation type-II synthetic pyrethroid. Pre-exposure of rats to IMS (15 min/day) or FSS (3 min/day) for 28 days on LCT (3.0 mg/kg body weight, p.o.) treatment for 3 days resulted to decrease spatial learning and memory and muscle strength associated with cholinergic-muscarinic receptors in frontal cortex and hippocampus as compared to those exposed to IMS or FSS or LCT alone. Decrease in acetylcholinesterase activity, protein expression of ChAT and PKC-β1 associated with decreased mRNA expression of CHRM2, AChE and ChAT in frontal cortex and hippocampus was also evident in rats pre-exposed to IMS or FSS on LCT treatment, compared to rats exposed to IMS or FSS or LCT alone. Interestingly, changes both in behavioral and neurochemical endpoints were marginal in rats subjected to IMS or FSS for 28 days or those exposed to LCT for 3 days alone, compared to controls. The results suggest that stress is an important contributor in LCT induced cholinergic deficits. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dietary intake of the short-chain triglyceride triacetin vs. long-chain triglycerides decreases adipocyte diameter and fat deposition in rats.

PubMed

Lynch, J W; Bailey, J W

1995-05-01

Diets containing either triacetin (the water-soluble triglyceride of acetate) or long-chain triglycerides (LCT) were fed to rats for 30 d to determine the effect on body weight gain and adipose tissue cellularity. Male Sprague-Dawley rats were allowed free access to one of three diets: a control diet containing 5% of energy as fat or one of two experimental diets that contained 30% triglyceride (by energy). The source of the triglyceride in the two experimental groups was either 100% LCT or 95% triacetin + 5% LCT. Within the experimental groups receiving 30% fat, the source of dietary triglyceride (LCT vs. triacetin) did not affect total energy consumption. There were no significant differences in body weight at the onset of the study; however, animals fed 100% LCT weighed significantly more than the other two groups at the end of the study. In all three fat pads studied, animals fed triacetin had significantly lower pad mass than did animals fed LCT. Mean fat cell size was smaller in fat depots of animals fed short-chain triglyceride. Provision of dietary energy as the short-chain triglyceride triacetin in lieu of LCT resulted in lower weight gain and fat deposition. These data demonstrate the impact of dietary triglyceride composition on body weight regulation.

COMPASS Final Report: Lunar Communications Terminal (LCT)

NASA Technical Reports Server (NTRS)

Oleson, Steven R.; McGuire, Melissa L.

2010-01-01

The Lunar Communications Terminal (LCT) COllaborative Modeling and Parametric Assessment of Space Systems (COMPASS) session designed a terminal to provide communications between lunar South Pole assets, communications relay to/from these assets through an orbiting Lunar Relay Satellite (LRS) and navigation support. The design included a complete master equipment list, power requirement list, configuration design, and brief risk assessment and cost analysis. The Terminal consists of a pallet containing the communications and avionics equipment, surrounded by the thermal control system (radiator), an attached, deployable 10-m tower, upon which were mounted locally broadcasting and receiving modems and a deployable 1 m diameter Ka/S band dish which provides relay communications with the lunar relay satellites and, as a backup, Earth when it is in view. All power was assumed to come from the lunar outpost Habitat. Three LCT design options were explored: a stand-alone LCT servicing the manned outpost, an integrated LCT (into the Habitat or Lunar Lander), and a mini-LCT which provides a reduced level of communication for primarily robotic areas dealing as in situ resource utilization (ISRU) and remote science. Where possible all the designs assumed single fault tolerance. Significant mass savings were found when integrating the LCT into the Habitat or Lander but increases in costs occurred depending upon the level of man rating required for such designs.

Vitamin E modulates reproductive toxicity of pyrethroid lambda-cyhalothrin in male rabbits.

PubMed

Yousef, Mokhtar I

2010-05-01

The objective of the current study was to analyze the reproductive toxicity caused by lambda-cyhalothrin (LCT) in male rabbits, and to evaluate the possible protective effect of vitamin E (Vit. E) as antioxidant. Animals were orally administered their respective doses of LCT every other day and given drinking water supplemented with vitamin E for 16 weeks. Results showed that semen quality was deteriorated following treatment with LCT. Also, testosterone levels, body weight (BW), feed intake (FI), and relative testes (RTW) and epididymis (REW) weights were significantly decreased. Concentrations of thiobarbituric acid-reactive substances (TBARS) were significantly increased in seminal plasma of rabbits treated with LCT compared with control. While, activities of glutathione S-transferase (GST), transaminases and acid phosphatase (AcP) were significantly decreased. Vitamin E alone significantly increased testosterone levels, BW, FI, RTW, REW, semen characteristics and seminal plasma enzymes, and decreased the levels of TBARS. Also, the present study showed that vitamin E might be effective against LCT-induced reproductive toxicity. It was suggested that LCT exerted a significant adverse effect on reproductive performance of male rabbits. Furthermore, vitamin E antagonized the toxic effects of LCT and improved semen quality of male rabbit. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Correlating Corneal Biomechanics and Ocular Biometric Properties with Lamina Cribrosa Measurements in Healthy Subjects.

PubMed

Pérez Bartolomé, Francisco; Martínez de la Casa, Jose María; Camacho Bosca, Irene; Sáenz-Francés, Federico; Aguilar Munoa, Soledad; Martín Juan, Alberto; Garcia-Feijoo, Julian

2018-01-01

To examine interrelations between corneal biomechanics, ocular biometric variables and optic disc size (ODS), lamina cribosa depth (LCD) or thickness (LCT) in a healthy population. In a cross-sectional case-control study, the following measurements were made in 81 eyes of 81 participants: axial length, anterior chamber depth, lens thickness, and central corneal thickness using the optical biometer Lenstar LS900; and corneal hysteresis (CH), corneal resistance factor (CRF), Goldman-correlated intraocular pressure (IOPg), and corneal-compensated IOP (IOPcc) using the Ocular Response Analyzer. Serial horizontal enhanced depth imaging optical coherence tomography (EDI OCT) B-scans of the optic nerve head were obtained in each participant. Mean ODS, mean LCD, and mean LCT were measured in 11 equally spaced horizontal B-scans, excluding the LC insertion area under Bruch's membrane and scleral rim. LCD was measured in 74 of 81 eyes (91.36%); LCT in 60/81 (75.3%); ODS in 81/81 (100%). CRF was poorly, but significantly, correlated with LCT (Pearson's R = 0.264; P = 0.045). IOPcc, IOPg, CH, and ocular biometrics variables were poorly (non-significantly) correlated with LCD, LCT, and ODS. CRF was poorly but directly correlated with LCT. No association was detected between CH or ocular biometric variables and ODS, LCD, or LCT.

Parenteral medium-chain triglyceride-induced neutrophil activation is not mediated by a Pertussis Toxin sensitive receptor.

PubMed

Versleijen, Michelle W J; van Esterik, Joantine C J; Roelofs, Hennie M J; van Emst-de Vries, Sjenet E; Willems, Peter H G M; Wanten, Geert J A

2009-02-01

Lipid-induced immune modulation might contribute to the increased infection rate that is observed in patients using parenteral nutrition. We previously showed that emulsions containing medium-chain triglycerides (LCT/MCTs or pure MCTs), but not pure long-chain triglycerides (LCTs), impair neutrophil functions, modulate cell-signaling and induce neutrophil activation in vitro. It has recently been shown that medium-chain fatty acids are ligands for GPR84, a pertussis toxin (PT)-sensitive G-protein-coupled receptor (GPCR). This finding urged us to investigate whether MCT-induced neutrophil activation is mediated by PT-sensitive GPCRs. Neutrophils isolated from blood of healthy volunteers were pre-incubated with PT (0.5-1 microg/mL, 1.5 h) and analyzed for the effect of this pre-incubation on LCT/MCT (2.5 mmol/L)-dependent modulation of serum-treated zymosan (STZ)-induced intracellular Ca(2+) mobilization and on LCT/MCT (5 mmol/L)-induced expression of cell surface adhesion (CD11b) and degranulation (CD66b) markers and oxygen radical (ROS) production. PT did not inhibit the effects of LCT/MCT on the STZ-induced increase in cytosolic free Ca(2+) concentration. LCT/MCT increased ROS production to 146% of unstimulated cells. However, pre-incubation with PT did not inhibit the LCT/MCT-induced ROS production. Furthermore, the LCT/MCT-induced increase in CD11b and CD66b expression (196% and 235% of unstimulated cells, respectively) was not inhibited by pre-incubation with PT. LCT/MCT-induced neutrophil activation does not involve the action of a PT-sensitive G-protein-coupled receptor.

Lipid effects on neutrophil calcium signaling induced by opsonized particles: platelet activating factor is only part of the story.

PubMed

Wanten, Geert; Kusters, Anneke; van Emst-de Vries, Sjenet E; Tool, Anton; Roos, Dirk; Naber, Ton; Willems, Peter

2004-08-01

Total parenteral nutrition is frequently used in clinical practice to improve the nutritional status of patients. However, the risk for infectious complications remains a drawback in which immune-modulating effects of the lipid component may play a role. To characterize these lipid effects we investigated neutrophil activation by opsonized yeast particles under influence of lipid emulsions derived from fish oil (VLCT), olive oil (LCT-MUFA), soybean oil (LCT), and a physical mixture of coconut and soybean oil (LCT-MCT). Serum-treated zymosan (STZ) evoked a biphasic increase in cytosolic Ca2+ concentration ([Ca2+]c) with an initial slow rise that turned into a second fast rise until a plateau was reached. LCT-MCT (5 mM) pretreatment markedly increased the rate of [Ca2+]c rise during the initial phase, abolished the second phase and lowered the plateau. These effects of LCT-MCT were mimicked by the protein kinase C (PKC) activating phorbol ester PMA. LCT, LCT-MUFA and VLCT, on the other hand, decreased the rate of [Ca2+]c rise during both phases and lowered the plateau. The platelet-activating factor (PAF) receptor antagonist WEB 2086 inhibited the second phase, demonstrating that PAF acts as an intercellular messenger in STZ-induced Ca2+ mobilization, but did not interfere with the stimulatory effect of LCT-MCT or PMA on the initial rate of [Ca2+]c rise. Structurally different lipids act only in part through PAF to distinctively modulate neutrophil calcium signaling in response to activation by opsonized particles. Copyright 2003 Elsevier Ltd.

The Th1/Th2 paradigm in lambda cyhalothrin-induced spleen toxicity: The role of thymoquinone.

PubMed

Hussein, Mohamed M A; Ahmed, Mona M

2016-01-01

This study investigates the retrofitted role of thymoquinone (TQ) in the Th1/Th2 paradigm imbalance in lambda-cyhalothrin (LCT) treated rats. Four groups of male Wistar rats were formed: Group I served as control. Group II received 5 mg TQ/(kg bw) daily. Group III received 0.6 mg LCT/(kg bw). Group IV was treated with TQ and LCT. All treatments were given orally for 10 weeks. The LCT-treated group elicited a significant increase in MDA and NO levels with up-regulation of NF-κB/p65 and pro-inflammatory genes expression and their levels. Meanwhile, GSH and immunoglobulins concentrations were markedly decreased concomitant with lessening the activities of antioxidant enzymes and anti-inflammatory cytokine genes mRNA levels. The co-administration of TQ and LCT improved the altered antioxidant enzymes activities and concentration of cytokines with attenuation of NF-κB/p65 mRNA. These data support the antioxidant role of TQ in the Th1/Th2 imbalance paradigm during LCT toxicity. Copyright © 2015 Elsevier B.V. All rights reserved.

Influence of immobilization and forced swim stress on the neurotoxicity of lambda-cyhalothrin in rats: Effect on brain biogenic amines and BBB permeability.

PubMed

Shukla, Rajendra K; Dhuriya, Yogesh K; Chandravanshi, Lalit P; Gupta, Richa; Srivastava, Pranay; Pant, Aditya B; Kumar, Ajay; Pandey, Chandra M; Siddiqui, M Haris; Khanna, Vinay K

2017-05-01

Experimental studies have been carried out on rats to understand the influence of immobilization stress (IMS), a psychological stressor and forced swim stress (FSS), a physical stressor in the neurotoxicity of lambda-cyhalothrin (LCT), a new generation type II synthetic pyrethroid with extensive applications. No significant change in plasma corticosterone levels and blood brain barrier (BBB) permeability was observed in rats subjected to IMS (one session of 15min/day), FSS (one session of 3min/day) for 28days or LCT treatment (3.0mg/kg body weight, p.o. suspended in groundnut oil) for 3days (26th, 27th and 28th day) as compared to controls. Marginal changes in the levels of biogenic amines and their metabolites (NE, EPN, DA, HVA, DOPAC, 5-HT) in hypothalamus, frontal cortex, hippocampus, and corpus striatum were observed in rats subjected to IMS or FSS or LCT alone as compared to controls. It was interesting to note that pre-exposure to IMS or FSS followed by LCT treatment for 3days caused a marked increase in plasma corticosterone levels associated with disruption in the BBB permeability as compared to rats exposed to IMS or FSS or LCT alone. Pre-exposure to IMS or FSS followed by LCT treatment for 3days resulted to alter the levels of biogenic amines and their metabolites in hypothalamus, frontal cortex, hippocampus, and corpus striatum as compared to rats exposed to IMS or FSS or LCT alone. Although neurochemical changes were more intense in rats pre-exposed to IMS as compared to those subjected to FSS on LCT treatment, the results indicate that both psychological and physical stress could be important influencing factors in the neurotoxicity of LCT. Copyright © 2016. Published by Elsevier B.V.

Characterization of emission microscopy and liquid crystal thermography in IC fault localization

NASA Astrophysics Data System (ADS)

Lau, C. K.; Sim, K. S.

2013-05-01

This paper characterizes two fault localization techniques - Emission Microscopy (EMMI) and Liquid Crystal Thermography (LCT) by using integrated circuit (IC) leakage failures. The majority of today's semiconductor failures do not reveal a clear visual defect on the die surface and therefore require fault localization tools to identify the fault location. Among the various fault localization tools, liquid crystal thermography and frontside emission microscopy are commonly used in most semiconductor failure analysis laboratories. Many people misunderstand that both techniques are the same and both are detecting hot spot in chip failing with short or leakage. As a result, analysts tend to use only LCT since this technique involves very simple test setup compared to EMMI. The omission of EMMI as the alternative technique in fault localization always leads to incomplete analysis when LCT fails to localize any hot spot on a failing chip. Therefore, this research was established to characterize and compare both the techniques in terms of their sensitivity in detecting the fault location in common semiconductor failures. A new method was also proposed as an alternative technique i.e. the backside LCT technique. The research observed that both techniques have successfully detected the defect locations resulted from the leakage failures. LCT wass observed more sensitive than EMMI in the frontside analysis approach. On the other hand, EMMI performed better in the backside analysis approach. LCT was more sensitive in localizing ESD defect location and EMMI was more sensitive in detecting non ESD defect location. Backside LCT was proven to work as effectively as the frontside LCT and was ready to serve as an alternative technique to the backside EMMI. The research confirmed that LCT detects heat generation and EMMI detects photon emission (recombination radiation). The analysis results also suggested that both techniques complementing each other in the IC fault localization. It is necessary for a failure analyst to use both techniques when one of the techniques produces no result.

Hepatocellular integrity in patients requiring parenteral nutrition: comparison of structured MCT/LCT vs. a standard MCT/LCT emulsion and a LCT emulsion.

PubMed

Piper, S N; Röhm, K D; Boldt, J; Odermatt, B; Maleck, W H; Suttner, S W

2008-07-01

The aetiology of parenteral nutrition-associated hepatic injury remains unresolved. The aim of the study was to evaluate the effects of structured triglycerides in parenteral nutrition compared either to a physical medium-chain triglycerides (MCT)/long-chain triglcerides (LCT) mixture or to a LCT emulsion on hepatic integrity. In a randomized, double-blinded trial, we studied 45 patients undergoing abdominal surgery, who were expected to receive parenteral nutrition for 5 days. Patients were allocated to one of three nutrition regimens: Group A (n = 15) received structured triglycerides, Group B (n = 15) a MCT/LCT and Group C (n = 15) a LCT lipid emulsion. Before the start of parenteral nutrition (T0), 24 h (T1), 48 h (T2), 72 h (T3) and 120 h (T4) after start of infusion the following parameters were measured: Alpha-glutathione S-transferase (alpha-GST), alanine aminotransferase (ALT), aspartate aminotransferase (AST), glucose and serum triglycerides. At T3 and T4, alpha-GST levels were significantly higher in Group B (T3: 9.4 +/- 9.9; T4: 14.6 +/- 19.5 microg L-1) and Group C (T3: 14.2 +/- 20.8; T4: 22.4 +/- 39.3 microg L-1) compared with the patients receiving structured triglycerides (T3: 1.9 +/- 1.8; T4: 3.2 +/- 2.7 microg L-1). Whereas the mean alpha-GST-levels in structured triglycerides group always remained in the normal range, this was not the case in both other groups at T3 and T4. There were no significant differences concerning ALT, AST and glucose levels. At T3 and T4, triglyceride levels were significantly lower in Group A than in Groups B and C. Hepatic integrity was well retained with the administration of structured triglycerides, whereas both MCT/LCT emulsion and LCT emulsion caused subclinical hepatic injury.

Comparison of diet-induced thermogenesis of foods containing medium- versus long-chain triacylglycerols.

PubMed

Kasai, Michio; Nosaka, Naohisa; Maki, Hideaki; Suzuki, Yoshie; Takeuchi, Hiroyuki; Aoyama, Toshiaki; Ohra, Atsushi; Harada, Youji; Okazaki, Mitsuko; Kondo, Kazuo

2002-12-01

The purpose of this study was to investigate the effect of 5-10 g of medium-chain triacylglycerols (MCT) on diet-induced thermogenesis in healthy humans. The study compared diet-induced thermogenesis after ingestion of test foods containing MCT and long-chain triacylglycerols (LCT), using a double-blind, crossover design. Eight male and eight female subjects participated in study 1 and study 2, respectively. In both studies, the LCT was a blend of rapeseed oil and soybean oil. In study 1, the liquid meals contained 10 g MCT (10M), a mixture of 5 g MCT and 5 g LCT (5M5L), and 10 g LCT (10L). In study 2, the subjects were given a meal (sandwich and clear soup) with the mayonnaise or margarine containing 5 g of MCT or LCT. Postprandial energy expenditure was measured by indirect calorimetry before and during the 6 h after ingestion of the test meals. Diet-induced thermogenesis was significantly greater after 5M5L and 10M Ingestion as compared to 10L ingestion. Ingestion of the mayonnaise or margarine containing 5 g MCT caused significantly larger diet-induced thermogenesis as compared to that of LCT. These results suggest that, in healthy humans, the intake of 5-10 g of MCT causes larger diet-induced thermogenesis than that of LCT, irrespective of the form of meal containing the MCT.

Lecture Capture Technology and Student Performance in an Operations Management Course

ERIC Educational Resources Information Center

Sloan, Thomas W.; Lewis, David A.

2014-01-01

Lecture capture technologies (LCT) such as Echo360, Mediasite, and Tegrity have become very popular in recent years. Many studies have shown that students favor the use of such technology, but relatively little research has studied the impact of LCT on learning. This article examines two research questions: (1) whether the use of LCT actually…

[Effects of postnatal lambda-cyhalothrin exposure on synaptic proteins in ICR mouse brain].

PubMed

Bao, Xun-Di; Wang, Qu-Nan; Li, Fang-Fang; Chai, Xiao-Yu; Gao, Ye

2011-04-01

To evaluate the influence on the synaptic protein expression in different brain regions of ICR mice after lambda-cyhalothrin (LCT) exposure during postnatal period. Two male and 4 female healthy ICR mice were put in one cage. It was set as pregnancy if vaginal plug was founded. Offspring were divided into 5 groups randomly, and exposed to LCT (0.01% DMSO solution) at the doses of 0.1, 1.0 and 10.0 mg/kg by intragastric rout every other day from postnatal days (PND) 5 to PND13, control animals were treated with normal saline or DMSO by the same route. The brains were removed from pups on PND 14, the synaptic protein expression levels in cortex, hippocampus and striatum were measured by western blot. GFAP levels of cortex and hippocampus in the LCT exposure group increased with doses, as compared with control group (P < 0.05), while Tuj protein expression did not change significantly in the various brain regions of ICR mice. GAP-43 protein expression levels in the LCT exposed mouse hippocampus and in female ICR mouse cortex increased with doses, as compared with control group (P < 0.05). Presynaptic protein (Synapsin I) expression levels did not change obviously in various brain regions. However, postsynaptic density protein 95 (PSD95) expression levels of the hippocampus and striatum in male offspring of 10.0 mg/kg LCT group, of cortex of female LCT groups, and of female offspring in all exposure groups, of striatum, in 1.0 or 10.0 mg/kg LCT exposure groups significantly decreased (P < 0.05). Early postnatal exposure to LCT affects synaptic protein expression. These effects may ultimately affect the construction of synaptic connections.

The effects of different lipid emulsions on the lipid profile, fatty acid composition, and antioxidant capacity of preterm infants: A double-blind, randomized clinical trial.

PubMed

Wang, Ying; Feng, Yi; Lu, Li-Na; Wang, Wei-Ping; He, Zhen-Juan; Xie, Li-Juan; Hong, Li; Tang, Qing-Ya; Cai, Wei

2016-10-01

Olive oil (OO), medium-chain triglycerides (MCT)/long-chain triglycerides (LCT) mixture and soybean oil (SO) lipid emulsions are currently used for preterm infants in China. The aim of our study was to compare the lipid profile, fatty acid composition, and antioxidant capacity of preterm infants administered OO, MCT/LCT, or SO lipid emulsions. In this study, 156 preterm infants (birth weight < 2000 g and gestational age < 37 weeks) received parenteral nutrition (PN) containing OO, MCT/LCT, or SO lipid emulsions for a minimum of 14 d. On days 0, 7, and 14, the lipid profile, fatty acid composition and antioxidant capacity were analyzed. On day 7, HDL levels in the MCT/LCT group were significantly lower than in the OO (1.06 ± 0.40 mmol/L) or SO groups. LDL levels were higher in the OO group than in the MCT/LCT or SO groups on day 7. A-I/B was higher in MCT/LCT than in OO or SO groups. Myristic acid (C14:0) levels on days 7 and 14 increased in MCT/LCT compared to the OO and SO groups. The OO group had higher oleic acid (C18:1n9) levels than the two other groups. Linoleic acid (C18:2n6), linolenic acid (C18:3n3), and eicosapentaenoic acid (20:5n3) were significantly lower in the OO group than in MCT/LCT or SO groups. Monounsaturated fatty acid levels decreased, and ω-6 polyunsaturated fatty acid and essential fatty acids levels increased in MCT/LCT and SO groups. No significant differences were obtained in SOD, MDA, GSH-Px, and T-AOC among the groups. The three lipid emulsions were safe and well tolerated in preterm infants. Oleic acid (C18:1n9) levels increased and LA (C18:2n6), ALA (C18:3n3), and EPA (C20:5n23) levels decreased in OO compared to MCT/LCT or SO. NCT01683162, https://register.clinicaltrials.gov/. Copyright © 2015 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Age distribution of lithium-cesium-tantalum enriched pegmatites and relationships to orogeny

NASA Astrophysics Data System (ADS)

McCauley, A.; Bradley, D. C.

2011-12-01

Pegmatites account for about one third of the world's lithium production, most of the tantalum, and all of the cesium. Pegmatites enriched in these elements (LCT pegmatites) are widely interpreted as extreme fractionation products of orogenic granitic melts, although it is not always possible to tie a particular pegmatite to a known granite of the same age. The global age distribution of LCT pegmatites is similar to the age distributions of common pegmatites, of orogenic granites, and of detrital zircons. Our geochronological synthesis expands on, and generally confirms, the recent study by Tkachev (2011, Geol. Soc. Spec. Publ. 350, 7). The LCT pegmatite maxima at ca. 2650, 1800, 525, 350, and 100 Ma correspond to times of collisional orogeny and, except for the comparatively minor peak at 100 Ma, to times of supercontinent assembly. Between these pulses are long intervals of few or no LCT pegmatites. Global minima in LCT pegmatite abundance overlap with supercontinent tenures at ca. 2450-2225, 1625-1000, 875-725, and 250-200 Ma, as established, for the Precambrian, from global minima in the abundances of passive margins and detrital zircons. A key question that bears on both metallogenesis and exploration strategies is why are some orogenic belts well endowed with LCT pegmatites, whereas other, seemingly similar orogens are barren? For the present study, LCT pegmatites from the Appalachian, Variscan, Damara, and Argentine Precordilleran orogens are being dated by the U-Pb method to relate pegmatite emplacement to other igneous events, shortening, metamorphism, foreland-basin sedimentation, and, on the broadest scale, to supercontinent assembly. Anecdotal evidence suggests that LCT pegmatites typically are emplaced late in orogenic cycles. In the Inland Branch of the Damaride orogen, about 45 m.y. elapsed between initial arc-passive margin collision at ca. 550 Ma and LCT pegmatite emplacement at ca. 505 Ma, very late in the assembly of this part of Gondwana. In the Appalachian orogen, LCT pegmatites evidently were emplaced at ca. 345 and ca. 275 Ma-long after initial arc-passive margin collision. Neither time is particularly remarkable in the long sequence of Appalachian orogenic events. The ca. 275 Ma event was coeval with the last increment of Appalachian plate convergence during the final assembly of Pangea. Possible triggers for melt generation in various pegmatite provinces include late collisional crustal thickening, shear heating, mantle plumes, slab break-off, and lower lithospheric delamination.

Comparison of Quick Lactose Intolerance Test in duodenal biopsies of dyspeptic patients with single nucleotide polymorphism LCT-13910C>T associated with primary hypolactasia/lactase-persistence.

PubMed

Mattar, Rejane; Basile-Filho, Anibal; Kemp, Rafael; Santos, José Sebastião dos

2013-01-01

To analyze the usefulness of Quick Lactose Intolerance Test in relation to the genetic test based on LCT-13910C>T genotypes, previously validated for clinical practice, for primary hypolactasia/lactase-persistence diagnosis. Thirty-two dyspeptic patients that underwent upper gastrointestinal endoscopy entered the study. Two postbulbar duodenal biopsies were taken for the Quick test, and gastric antral biopsy for DNA extraction and LCT-13910C>T polymorphism analysis. DNA was also extracted from biopsies after being used in the Quick Test that was kept frozen until extraction. Nine patients with lactase-persistence genotype (LCT-13910CT or LCT-13910TT) had normolactasia, eleven patients with hypolactasia genotype (LCT-13910CC) had severe hypolactasia, and among twelve with mild hypolactasia, except for one that had LCT-13910CT genotype, all the others had hypolactasia genotype. The agreement between genetic test and quick test was high (p<0.0001; Kappa Index 0.92). Most of the patients that reported symptoms with lactose-containing food ingestion had severe hypolactasia (p<0.05). Amplification with good quality PCR product was also obtained with DNA extracted from biopsies previously used in the Quick Test; thus, for the future studies antral gastric biopsies for genetic test would be unnecessary. Quick test is highly sensitive and specific for hypolactasia diagnosis and indicated those patients with symptoms of lactose intolerance.

Chlorpyrifos and lambda cyhalothrin-induced oxidative stress in human erythrocytes.

PubMed

Deeba, Farah; Raza, Irum; Muhammad, Noor; Rahman, Hazir; Ur Rehman, Zia; Azizullah, Azizullah; Khattak, Baharullah; Ullah, Farman; Daud, M K

2017-04-01

Pesticides are one of the most potentially harmful chemicals introduced into the environment, and their adverse impacts on non-target organisms can be significant. The present study was conducted to shed light on effects of locally used insecticides chlorpyrifos (CPF) and lambda cyhalothrin (LCT) on oxidative stress biomarkers in human erythrocytes. The activity of catalase (CAT), superoxide dismutase (SOD), and protein contents as well as the levels of malondialdehyde (MDA) and osmotic fragility (OF) were measured in human erythrocytes exposed to CPF at concentrations of 0, 100, 500, 1000, and 2000 ppm and LCT at concentrations of 0, 100, 300, 600, and 800 ppm for 1 h and 3 h at 37°C. MDA levels and OF of erythrocytes were significantly higher in erythrocytes incubated with CPF and LCT at increasing concentrations of both insecticides and increased incubation time. However, erythrocyte CAT and SOD activities were decreased at all concentrations of CPF and LCT tested. Protein oxidation products were decreased at lower doses of CPF (100 and 500 ppm); at higher doses (1000 and 2000 ppm), total protein content was increased compared with control. In contrast LCT was associated with decreased in protein contents at all the concentrations. These results clearly demonstrated that CPF and LCT can induce oxidative stress in human erythrocytes ( in vitro).

The in vitro effect of Lambda-cyhalothrin on quality and antioxidant responses of rainbow trout Oncorhynchus mykiss spermatozoa.

PubMed

Kutluyer, Filiz; Erişir, Mine; Benzer, Fulya; Öğretmen, Fatih; İnanan, Burak Evren

2015-11-01

There is little information in the scientific literature about effect of in vitro exposure of fish spermatozoa to pesticides. In vitro effect of Lambda-cyhalothrin (LCT) on sperm quality and oxidative stress has not been fully explored yet. The effects of LCT, which is a synthetic pyrethroid insecticide, on quality and oxidative stress of spermatozoa were investigated in vitro due to extensively use to control a wide range of insect pests in agriculture, public health, and homes and gardens. To explore the potential in vitro toxicity of LCT, fish spermatozoa were incubated with different concentrations of LCT (0.6, 1.2 and 2.4 μg/L) for 2h. Reduced glutathione (GSH), glutathione peroxidase (GSH-Px), catalase (CAT) and malondialdehyde (MDA) in spermatozoa were analyzed for determination of oxidant and antioxidant balance. Our results indicated that the percentage and duration of sperm motility significantly decreased with exposure to LCT. Activity of GSH-Px and MDA (P<0.05) and GSH levels (P<0.05) increased in a concentration-dependent manner while CAT activity decreased (P<0.05). In conclusion, the oxidant and antioxidant status and sperm quality were affected by increasing concentrations of LCT. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of medium/ω-6 long chain triglyceride-based emulsion on leucocyte death and inflammatory gene expression

PubMed Central

Cury-Boaventura, M F; Gorjão, R; Martins de Lima, T; Fiamoncini, J; Godoy, A B P; Deschamphs, F C; Soriano, F G; Curi, R

2011-01-01

Lipid emulsion (LE) containing medium/ω-6 long chain triglyceride-based emulsion (MCT/ω-6 LCT LE) has been recommended in the place of ω-6 LCT-based emulsion to prevent impairment of immune function. The impact of MCT/ω-6 LCT LE on lymphocyte and neutrophil death and expression of genes related to inflammation was investigated. Seven volunteers were recruited and infusion of MCT/ω-6 LCT LE was performed for 6 h. Four volunteers received saline and no change was found. Blood samples were collected before, immediately afterwards and 18 h after LE infusion. Lymphocytes and neutrophils were studied immediately after isolation and after 24 and 48 h in culture. The following determinations were carried out: plasma-free fatty acids, triacylglycerol and cholesterol concentrations, plasma fatty acid composition, neutral lipid accumulation in lymphocytes and neutrophils, signs of lymphocyte and neutrophil death and lymphocyte expression of genes related to inflammation. MCT/ω-6 LCT LE induced lymphocyte and neutrophil death. The mechanism for MCT/ω-6 LCT LE-dependent induction of leucocyte death may involve changes in neutral lipid content and modulation of expression of genes related to cell death, proteolysis, cell signalling, inflammatory response, oxidative stress and transcription. PMID:21682721

High-performance mirror for space applications using anodic bonding technology

NASA Astrophysics Data System (ADS)

Otto, W.; Fischer, E.; Kemper, J.; Koch, S.; Kolberg, J.; Kramer, C.; Kunde, J.; Läger, M.

2017-11-01

Berliner Glas developed and manufactured the plane elliptical shaped mirrors for the Synopta Coarse Pointing Assembly (CPA) being one of the key elements of the TESAT Spacecom Laser Communication Terminals (LCT's). The first TESAT LCT containing a Synopta CPA was embarked on Sentinel 1A and is in orbit since April 2014. TESAT Spacecom LCT's have been successfully tested in space since 2007 and are now operationally used in commercial satellite communication systems.

Lambda cyhalothrin toxicity induces alterations in lipogenic genes and inflammatory factors in rat liver.

PubMed

Moustafa, Gihan G; Hussein, Mohamed M A

2016-02-01

The present study aims to elucidate the molecular basis of lambda cyhalothrin (LCT) toxicity. Thirty-two mature male albino rats were randomly classified into four equal groups. The first group was orally administered normal saline, the second group was orally administered dimethylsulfoxide (DMSO). The third group was orally administered 1/100 LD50 (6.12 mg/kg b. wt) of a commercial formulation containing 2.5% LCT (i.e., a net dose LCT corresponding to 0.15 mg/kg b. wt). The fourth group was orally administered 1/100 LD50 (0.64 mg/kg b. wt) of a pure form of LCT. The results indicated that exposure to LCT is capable of inducing an up-regulation in the mRNA expression levels of peroxisome proliferative activated receptor α and γ (PPAR α and PPAR γ), tumor necrosis factor (TNF-α), fatty acid synthase (FAS) and sterol regulatory element binding protein-1c (SREBP-1c). Additionally, our study revealed a significant increase in serum levels of ALT, AST, ALP, γGT as well as the inflammatory cytokines TNF-α and monocyte chemoattractant protein-1 (MCP-1). A significant elevation in total lipids, total cholesterol, triacylglycerol, LDL-c and leptin with a corresponding significant decrease in HDL-c was also noted. Moreover, our results depicted that LCT treatment exhibits a significant increase in hepatic MDA levels concurrent with a significant decrease in GSH levels and the activities of CAT, SOD, and GPx. An immunohistochemical investigation also revealed a strong up-regulation of hepatic FAS in the LCT treated groups. The histopathological findings were marked by evidence in support of periportal fatty changes and interstitial aggregation of round cells.

Association of lactase 13910 C/T polymorphism with bone mineral density and fracture risk: a meta-analysis.

PubMed

Wu, Yougen; Li, Yinghua; Cui, Yunqing; Zhou, Yunjiao; Qian, Qingqing; Hong, Yang

2017-12-01

A number of studies have investigated the association of lactase (LCT,C/T-13910) gene polymorphismwith bonemineral density (BMD) and fracture risk, but previous results were inconclusive. In this study, a meta-analysis was performed to quantify the association of LCT (C/T-13910) polymorphism with BMD and fracture risk. Eligible publications were searched in the PubMed, Web of Science, Embase databases, Google Scholar, Yahoo and Baidu. Pooled weighed mean difference (WMD) or odds ratio (OR) with their 95% confidence interval (CI) were calculated using a fixed-effects or random-effects model. A total of nine articles with 8871 subjects were investigated in the presentmeta-analysis. Overall, the TT/TC genotypes of LCT 13910 C/T polymorphism showed significantly higher BMD than those with the CC genotype at femur neck (FN) (WMD = 0.011 g/cm 2 , 95% CI = 0.004-0.018, P = 0.003). Besides, LCT 13910 C/T polymorphism may decrease the risk of any site fractures (for TT versus TC+CC, OR = 0.813, 95% CI = 0.704-0.938, P = 0.005; for T allele versus C allele, OR = 0.885, 95% CI = 0.792-0.989, P = 0.032). However, there was no significant association of LCT 13910 C/T polymorphism with BMD at lumbar spine and risk of vertebral fractures under all genetic contrast models (all P values were >0.05). The meta-analysis suggests that there are significant effects of LCT 13910 C/T polymorphism on BMD and fracture risk. Large-scale studies with different ethnic populations will be needed to further investigate the possible race-specific effect of LCT 13910 C/T polymorphism on BMD and fracture risk.

Lactase Non-Persistence Genotyping: Comparison of Two Real-Time PCR Assays and Assessment of Concomitant Fructose/Sorbitol Malabsorption Rates.

PubMed

Enko, Dietmar; Pollheimer, Verena; Németh, Stefan; Pühringer, Helene; Stolba, Robert; Halwachs-Baumann, Gabriele; Kriegshäuser, Gernot

2016-01-01

Genetic testing is a standard technique for the diagnosis of primary adult-type hypolactasia, also referred to as lactase non-persistence. The aim of this study was to compare the lactase gene (LCT) C/T-13910 polymorphism genotyping results of two commercially available real-time (RT)-PCR assays in patients referred to our outpatient clinic for primary lactose malabsorption testing. Furthermore, concomitant conditions of fructose/sorbitol malabsorption were assessed. Samples obtained from 100 patients were tested in parallel using the LCT T-13910C ToolSet for Light Cycler (Roche, Rotkreuz, Switzerland) and the LCT-13910C>T RealFast Assay (ViennaLab Diagnostics GmbH, Vienna, Austria). Additionally, patients were also screened for the presence of fructose/sorbitol malabsorption by functional hydrogen (H2)/methane (CH4) breath testing (HMBT). Cohen's Kappa (κ) was used to calculate the agreement between the two genotyping methods. The exact Chi-Square test was performed to compare fructose/sorbitol HMBT with LCT genotyping results. Twenty-one (21.0%) patients had a LCT C/C-13910 genotype suggestive of lactase non-persistence, and 79 (79.0%) patients were identified with either a LCT T/C-13910 or T/T-13910 genotype (i.e., lactase persistence). In all genotype groups, concordance between the two RT-PCR assays was 100%. Cohen's κ demonstrated perfect observed agreement (p < 0.001, κ = 1). Fructose and sorbitol malabsorption was observed in 13/100 (13.0%) and 25/100 (25.0%) individuals, respectively. Both RT-PCR assays are robust and reliable LCT genotyping tools in a routine clinical setting. Concomitant fructose and/or sorbitol malabsorption should be considered in individuals with suspected lactase-non-persistence. However, standardization of clinical interpretation of laboratory HMBT results is required.

Evaluation of Acute toxicity of Lambda Cyhalothrin in Mus musculus L.

PubMed

Tomar, Monika; Kumar, Ajay; Kataria, Sudhir Kumar

2015-08-01

Lambda Cyhalothrin (LCT) is a type II synthetic pyrethroid widely used in agriculture, home pest control and protection of food stuff. Here, we evaluated its toxicity on biochemical parameters (Total protein, Acetyl cholinesterase, RNA and DNA) and liver histological alteration in mice after 24 h of oral administration @ 25, 50 and 75% of LD50 i.e.; 26.49 mg/kg/body wt. Distilled water (DW) and Cyclophosphamide (CP @ 40 mg/kg/body wt.) were used as negative and positive control; respectively. LCT treated mice showed significant decrease in total protein (P < 0.01), acetyl cholinesterase (P < 0.001) and DNA (P < 0.001) in a dose dependent manner. On the contrary, RNA content showed significant increase (P < 0.01) at 50% of LD50 of LCT. Histological observations of the mice liver showed vascular congestion and hepatocyte degeneration with 6.63 mg/kg/body wt. of LCT; and accumulation of RBCs with sinusoid degeneration and wide necrotic area with pyknosis with 13.25 and 19.88 mg/kg/body wt., respectively. The results demonstrated LCT induced biochemical changes and hepatotoxicity in female mice.

Transceiver for Space Station Freedom

NASA Technical Reports Server (NTRS)

Fitzmaurice, M.; Bruno, R.

1990-01-01

This paper describes the design of the Laser Communication Transceiver (LCT) system which was planned to be flight tested as an attached payload on Space Station Freedom. The objective in building and flight-testing the LCT is to perform a broad class of tests addressing the critical aspects of space-based optical communications systems, providing a base of experience for applying laser communications technology toward future communications needs. The LCT's functional and performance requirements and capabilities with respect to acquisition, spatial tracking and pointing, communications, and attitude determination are discussed.

Transceiver for Space Station Freedom

NASA Astrophysics Data System (ADS)

Fitzmaurice, M.; Bruno, R.

1990-07-01

This paper describes the design of the Laser Communication Transceiver (LCT) system which was planned to be flight tested as an attached payload on Space Station Freedom. The objective in building and flight-testing the LCT is to perform a broad class of tests addressing the critical aspects of space-based optical communications systems, providing a base of experience for applying laser communications technology toward future communications needs. The LCT's functional and performance requirements and capabilities with respect to acquisition, spatial tracking and pointing, communications, and attitude determination are discussed.

Prenatal exposure to lambda-cyhalothrin alters brain dopaminergic signaling in developing rats.

PubMed

Dhuriya, Yogesh K; Srivastava, Pranay; Shukla, Rajendra K; Gupta, Richa; Singh, Dhirendra; Parmar, Devendra; Pant, Aditya B; Khanna, Vinay K

2017-07-01

The present study is focused to decipher the molecular mechanisms associated with dopaminergic alterations in corpus striatum of developing rats exposed prenatally to lambda-cyhalothrin (LCT), a new generation type II synthetic pyrethroid. There was no significant change in the mRNA and protein expression of DA-D1 receptors at any of the doses of LCT (0.5, 1 and 3mg/kg body weight) in corpus striatum of developing rats exposed prenatally to LCT on PD22 and PD45. Prenatal exposure to LCT (1 and 3mg/kg body weight) resulted to decrease the levels of mRNA and protein of DA-D2 receptors in corpus stratum of developing rats on PD22 as compared to controls. Decrease in the binding of 3H-Spiperone in corpus striatum, known to label DA-D2 receptors was also distinct in developing rats on PD22. These rats also exhibited decrease in the expression of proteins - TH, DAT and VMAT2 involved in pre-dopaminergic signaling. Further, decrease in the expression of DARPP-32 and pCREB associated with increased expression of PP1α was evident in developing rats on PD22 as compared to controls. Interestingly, a trend of recovery in the expression of these proteins was observed in developing rats exposed to LCT at moderate dose (1.0mg/kg body weight) while alteration in the expression of these proteins continued to persist in those exposed at high dose (3.0mg/kg body weight) on PD45 as compared to respective controls. No significant change in the expression of any of these proteins was observed in corpus striatum of developing rats prenatally exposed to LCT at low dose (0.5mg/kg body weight) on PD22 and PD45 as compared to respective controls. The results provide interesting evidence that alterations in dopaminergic signaling on LCT exposure are due to selective changes in DA-D2 receptors in corpus striatum of developing rats. Further, these changes could be attributed to impairment in spontaneous motor activity on LCT exposure in developing rats. Copyright © 2017 Elsevier B.V. All rights reserved.

2D non-separable linear canonical transform (2D-NS-LCT) based cryptography

NASA Astrophysics Data System (ADS)

Zhao, Liang; Muniraj, Inbarasan; Healy, John J.; Malallah, Ra'ed; Cui, Xiao-Guang; Ryle, James P.; Sheridan, John T.

2017-05-01

The 2D non-separable linear canonical transform (2D-NS-LCT) can describe a variety of paraxial optical systems. Digital algorithms to numerically evaluate the 2D-NS-LCTs are not only important in modeling the light field propagations but also of interest in various signal processing based applications, for instance optical encryption. Therefore, in this paper, for the first time, a 2D-NS-LCT based optical Double-random- Phase-Encryption (DRPE) system is proposed which offers encrypting information in multiple degrees of freedom. Compared with the traditional systems, i.e. (i) Fourier transform (FT); (ii) Fresnel transform (FST); (iii) Fractional Fourier transform (FRT); and (iv) Linear Canonical transform (LCT), based DRPE systems, the proposed system is more secure and robust as it encrypts the data with more degrees of freedom with an augmented key-space.

Using a Double-Coil TMS Protocol to Assess Preparatory Inhibition Bilaterally.

PubMed

Vassiliadis, Pierre; Grandjean, Julien; Derosiere, Gerard; de Wilde, Ysaline; Quemener, Louise; Duque, Julie

2018-01-01

Transcranial magnetic stimulation (TMS) applied over the primary motor cortex (M1), elicits motor-evoked potentials (MEPs) in contralateral limb muscles which are valuable indicators of corticospinal excitability (CSE) at the time of stimulation. So far, most studies have used single-coil TMS over one M1, yielding MEPs in muscles of a single limb-usually the hand. However, tracking CSE in the two hands simultaneously would be useful in many contexts. We recently showed that, in the resting state, double-coil stimulation of the two M1 with a 1 ms inter-pulse interval (double-coil 1 ms TMS) elicits MEPs in both hands that are comparable to MEPs obtained using single-coil TMS. To further evaluate this new technique, we considered the MEPs elicited by double-coil 1 ms TMS in an instructed-delay choice reaction time task where a prepared response has to be withheld until an imperative signal is displayed. Single-coil TMS studies have repetitively shown that in this type of task, the motor system is transiently inhibited during the delay period, as evident from the broad suppression of MEP amplitudes. Here, we aimed at investigating whether a comparable inhibitory effect can be observed with MEPs elicited using double-coil 1 ms TMS. To do so, we compared the amplitude as well as the coefficient of variation (CV) of MEPs produced by double-coil 1 ms or single-coil TMS during action preparation. We observed that MEPs were suppressed (smaller amplitude) and often less variable (smaller CV) during the delay period compared to baseline. Importantly, these effects were equivalent whether single-coil or double-coil 1 ms TMS was used. This suggests that double-coil 1 ms TMS is a reliable tool to assess CSE, not only when subjects are at rest, but also when they are involved in a task, opening new research horizons for scientists interested in the corticospinal correlates of human behavior.

Using a Double-Coil TMS Protocol to Assess Preparatory Inhibition Bilaterally

PubMed Central

Vassiliadis, Pierre; Grandjean, Julien; Derosiere, Gerard; de Wilde, Ysaline; Quemener, Louise; Duque, Julie

2018-01-01

Transcranial magnetic stimulation (TMS) applied over the primary motor cortex (M1), elicits motor-evoked potentials (MEPs) in contralateral limb muscles which are valuable indicators of corticospinal excitability (CSE) at the time of stimulation. So far, most studies have used single-coil TMS over one M1, yielding MEPs in muscles of a single limb—usually the hand. However, tracking CSE in the two hands simultaneously would be useful in many contexts. We recently showed that, in the resting state, double-coil stimulation of the two M1 with a 1 ms inter-pulse interval (double-coil1 ms TMS) elicits MEPs in both hands that are comparable to MEPs obtained using single-coil TMS. To further evaluate this new technique, we considered the MEPs elicited by double-coil1 ms TMS in an instructed-delay choice reaction time task where a prepared response has to be withheld until an imperative signal is displayed. Single-coil TMS studies have repetitively shown that in this type of task, the motor system is transiently inhibited during the delay period, as evident from the broad suppression of MEP amplitudes. Here, we aimed at investigating whether a comparable inhibitory effect can be observed with MEPs elicited using double-coil1 ms TMS. To do so, we compared the amplitude as well as the coefficient of variation (CV) of MEPs produced by double-coil1 ms or single-coil TMS during action preparation. We observed that MEPs were suppressed (smaller amplitude) and often less variable (smaller CV) during the delay period compared to baseline. Importantly, these effects were equivalent whether single-coil or double-coil1 ms TMS was used. This suggests that double-coil1 ms TMS is a reliable tool to assess CSE, not only when subjects are at rest, but also when they are involved in a task, opening new research horizons for scientists interested in the corticospinal correlates of human behavior. PMID:29568258

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael Viola, J. Edwards, T. Brown, L. Dudek, R. Ellis, P. Heitzenroeder, R. Strykowsky and Michael Cole

The National Compact Stellarator Experiment (NCSX) was a collaborative effort between ORNL and PPPL. PPPL provided the assembly techniques with guidance from ORNL to meet design criteria. The individual vacuum vessel segments, modular coils, trim coils, and toroidal field coils components were delivered to the Field Period Assembly (FPA) crew who then would complete the component assemblies and then assemble the final three field period assemblies, each consisting of two sets of three modular coils assembled over a 120o vacuum vessel segment with the trim coils and toroidal field coils providing the outer layer. The requirements for positioning the modularmore » coils were found to be most demanding. The assembly tolerances required for accurate positioning of the field coil windings in order to generate sufficiently accurate magnetic fields strained state of the art techniques in metrology and alignment and required constant monitoring of assembly steps with laser trackers, measurement arms, and photogrammetry. The FPA activities were being performed concurrently while engineering challenges were being resolved. For example, it was determined that high friction electrically isolated shims were needed between the modular coil interface joints and low distortion welding was required in the nose region of those joints. This took months of analysis and development yet the assembly was not significantly impacted because other assembly tasks could be performed in parallel with ongoing assembly tasks as well as tasks such as advance tooling setup preparation for the eventual welding tasks. The crew technicians developed unique, accurate time saving techniques and tooling which provided significant cost and schedule savings. Project management displayed extraordinary foresight and every opportunity to gain advanced knowledge and develop techniques was taken advantage of. Despite many risk concerns, the cost and schedule performance index was maintained nearly 1.0 during the assembly phase until project cancellation. In this paper, the assembly logic, the engineering challenges, solutions to those challenges and some of the unique and clever assembly techniques, will be presented.« less

Tissue and external insulation estimates and their effects on prediction of energy requirements and of heat stress.

PubMed

Berman, A

2004-05-01

Published data were used to develop improved equations to predict tissue insulation (TI) and external insulation (EI) and their effects on maintenance requirements of Holstein cattle. These are used to calculate lower critical temperature (LCT), energy cost of exposure to temperatures below LCT, and excess heat accumulating in the body at temperatures above LCT. The National Research Council classifies TI by age groups and body condition score; and in the EI equation air velocity effects are linear and coat insulation values are derived from beef animals in cold climates. These lead to low LCT values, which are not compatible with known effects of environment on the performance of Holsteins in warm climates. Equations were developed to present TI as a function of body weight, improving prediction of TI for animals of similar age but differing in body weight. An equation was developed to predict rate of decrease of TI at ambient temperatures above LCT. Nonlinear equations were developed that account for wind effects as boundary layer insulation effects dependent on body weight and air velocity. Published data were used to develop adjustments for hair coat effects on EI in Holstein cows. While by NRC equations, wind has negligible effects on heat loss, the recalculated effects of air velocity on heat loss were consistent with published effects of forced ventilation on the responses of the Holstein cow. The derived LCT was higher by 10 to 20 degrees C than that calculated by NRC (2001) and accounted for known Holstein performance in temperate and warm climates. These equations pointed to tentative significant effects of cold (-10 degrees C) on energy requirements (7 Mcal/d) further increased by 1 m/s wind (15 Mcal/d), even in high-producing cows. Needs for increased heat dissipation and estimating heat stress development at ambient temperatures above the LCT are predicted. These equations can be used to revise NRC equations for heat exchange.

[Digital angiography and lipiodol computerized tomography in the anatomopathological framework of hepatocarcinoma].

PubMed

Pozzi-Mucelli, R; Pozzi-Mucelli, R; Pagnan, L; Dalla Palma, L

1994-12-01

The introduction of therapies other than conventional surgery of hepatocellular carcinoma (HCC) requires an accurate pathologic classification, which is important because it is well known that HCC may have multicentric growth. The Liver Cancer Study Group of Japan has proposed a classification dividing HCCs into three macroscopic forms from the pathologic point of view: nodular, massive and infiltrating HCCs. The nodular type is subdivided into four types: single nodular type, single nodular type with surrounding proliferation, multinodular fused type and multinodular type. Forty-six HCC patients were examined with Lipiodol Computed Tomography (LCT) to investigate the agreement between pathologic and imaging findings. LCT proved to be in close agreement with pathologic findings. Sixteen cases were classified as type I (single nodular type), 8 as type II (single nodular type with limited foci), 1 as type III (multinodular fused type), 18 as type IV (multiple nodular type with diffuse foci) and 3 cases as type V (massive form). No cases of infiltrative forms were observed in our series. Based on LCT findings, the capabilities of digital subtraction angiography (DSA) were studied in the pathologic classification of HCCs. DSA exhibited some limitations in the pathologic classification of HCCs in 5 of 16 patients with type I lesions. In these cases DSA suggested false-positive diagnoses because of regenerative nodules in cirrhotic liver in 3 cases and of daughter nodules (not confirmed at LCT) in 2 cases. In 7 of 8 patients with type II HCCs, DSA failed to show the daughter nodules surrounding the main nodule. In the 18 patients with multiple distant nodules (type IV), DSA was less sensitive in defining nodule number and site. In the massive form, the information obtained with LCT and DSA was comparable. In conclusion, LCT should be considered a basic examination in the study of HCC extent. Based on LCT findings, the most appropriate treatment can be selected, be it surgery, alcohol injection, or intraarterial chemoembolization.

Nonuniform sampling theorems for random signals in the linear canonical transform domain

NASA Astrophysics Data System (ADS)

Shuiqing, Xu; Congmei, Jiang; Yi, Chai; Youqiang, Hu; Lei, Huang

2018-06-01

Nonuniform sampling can be encountered in various practical processes because of random events or poor timebase. The analysis and applications of the nonuniform sampling for deterministic signals related to the linear canonical transform (LCT) have been well considered and researched, but up to now no papers have been published regarding the various nonuniform sampling theorems for random signals related to the LCT. The aim of this article is to explore the nonuniform sampling and reconstruction of random signals associated with the LCT. First, some special nonuniform sampling models are briefly introduced. Second, based on these models, some reconstruction theorems for random signals from various nonuniform samples associated with the LCT have been derived. Finally, the simulation results are made to prove the accuracy of the sampling theorems. In addition, the latent real practices of the nonuniform sampling for random signals have been also discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lessard, Francois; Archambault, Louis; Plamondon, Mathieu

Purpose: Photon dosimetry in the kilovolt (kV) energy range represents a major challenge for diagnostic and interventional radiology and superficial therapy. Plastic scintillation detectors (PSDs) are potentially good candidates for this task. This study proposes a simple way to obtain accurate correction factors to compensate for the response of PSDs to photon energies between 80 and 150 kVp. The performance of PSDs is also investigated to determine their potential usefulness in the diagnostic energy range. Methods: A 1-mm-diameter, 10-mm-long PSD was irradiated by a Therapax SXT 150 unit using five different beam qualities made of tube potentials ranging from 80more » to 150 kVp and filtration thickness ranging from 0.8 to 0.2 mmAl + 1.0 mmCu. The light emitted by the detector was collected using an 8-m-long optical fiber and a polychromatic photodiode, which converted the scintillation photons to an electrical current. The PSD response was compared with the reference free air dose rate measured with a calibrated Farmer NE2571 ionization chamber. PSD measurements were corrected using spectra-weighted corrections, accounting for mass energy-absorption coefficient differences between the sensitive volumes of the ionization chamber and the PSD, as suggested by large cavity theory (LCT). Beam spectra were obtained from x-ray simulation software and validated experimentally using a CdTe spectrometer. Correction factors were also obtained using Monte Carlo (MC) simulations. Percent depth dose (PDD) measurements were compensated for beam hardening using the LCT correction method. These PDD measurements were compared with uncorrected PSD data, PDD measurements obtained using Gafchromic films, Monte Carlo simulations, and previous data. Results: For each beam quality used, the authors observed an increase of the energy response with effective energy when no correction was applied to the PSD response. Using the LCT correction, the PSD response was almost energy independent, with a residual 2.1% coefficient of variation (COV) over the 80-150-kVp energy range. Monte Carlo corrections reduced the COV to 1.4% over this energy range. All PDD measurements were in good agreement with one another except for the uncorrected PSD data, in which an over-response was observed with depth (13% at 10 cm with a 100 kVp beam), showing that beam hardening had a non-negligible effect on the PSD response. A correction based on LCT compensated very well for this effect, reducing the over-response to 3%.Conclusion: In the diagnostic energy range, PSDs show high-energy dependence, which can be corrected using spectra-weighted mass energy-absorption coefficients, showing no considerable sign of quenching between these energies. Correction factors obtained by Monte Carlo simulations confirm that the approximations made by LCT corrections are valid. Thus, PSDs could be useful for real-time dosimetry in radiology applications.« less

Absorption of calcium and magnesium in patients with intestinal resections treated with medium chain fatty acids

PubMed Central

Haderslev, K; Jeppesen, P; Mortensen, P; Staun, M

2000-01-01

BACKGROUND—Steatorrhoea is associated with increased faecal loss of calcium and magnesium. Medium chain C8-C10 triglycerides (MCTs) improve fat absorption in patients with small bowel resections but the effects on intestinal absorption of divalent cations are not clear.
AIM—To assess the effect of dietary replacement of long chain triglycerides (LCTs) with MCTs on calcium and magnesium absorption in patients with small bowel resections.
PATIENTS—Nineteen adult patients with a remaining small intestine averaging 171 cm (range 50-300).
METHODS—In a crossover design, patients were randomised to two high fat diets (10 MJ/day, 50% as fat) for four days each separated by one day of washout. Diets were prepared in duplicate and were based on either LCT (LCT period) or equal quantities of LCT and MCT (L/MCT period). Metabolic balances were calculated during the last three days of each period.
RESULTS—Mean stool volume increased significantly with the L/MCT diet and was 336 ml more than that with the LCT diet (95% confidence interval of mean difference, 26-649 ml). There was no significant change in the net absorption of calcium and magnesium between the two diets. On average, percentage calcium absorption was 8.6% with the LCT diet and 12.5% with the L/MCT diet. Mean percentage magnesium absorption was 5.4% with the LCT diet and 2.9% with the L/MCT diet.
CONCLUSIONS—Dietary replacement of 50% long chain triglycerides with medium chain triglycerides in small bowel resected patients increased faecal volume significantly. No changes in the intestinal net absorption of calcium and magnesium were demonstrated.


Keywords: medium chain triglycerides; calcium absorption; magnesium absorption; intestinal resections; fat absorption PMID:10807894

Thermal tolerance in bottlenose dolphins (Tursiops truncatus).

PubMed

Yeates, Laura C; Houser, Dorian S

2008-10-01

Water and air temperature are potentially limiting factors to the pole-ward distributions of coastal bottlenose dolphins. This study assessed the lower critical temperature of captive bottlenose dolphins to air temperature (LCT(a)) and water temperature (LCT(w)) through the use of open flow respirometry. Five dolphins, ranging from 14 to 33 years of age and acclimated to the waters of the southern California coast (14.2-22.5 degrees C), were subjected to water temperatures ranging from 0.2 to 18.0 degrees C. Two of the animals were additionally subjected to air temperatures ranging from -2.4 to 17.8 degrees C while maintaining water temperature approximately 3 degrees C above their individual LCT(w). The LCT(w) ranged from 5.5 to 10.6 degrees C and generally decreased with increasing animal mass; for dolphins in excess of 187 kg, the LCT(w) ranged from 5.5 to 5.7 degrees C. No LCT(a) could be determined across the range of air temperatures tested. Core body temperature remained within the limits of normal body temperatures reported for dolphins but demonstrated a direct relationship to water temperature in three subjects and varied across a range of 1.5 degrees C. Air and water temperature had a minimal synergistic effect on dolphin thermoregulation, i.e. water temperature exerted the predominant impact on thermoregulation. For dolphins in excess of 187 kg, water temperature alone would appear to be insufficient to limit the use of habitat north of current bottlenose dolphin ranges along the coastal United States. However, thermal impacts to smaller dolphins, in particular adolescents, neonates and accompanying females, may work in concert with other factors (e.g. prey distribution, predator avoidance, social interactions) to influence coastal residency patterns and population structure.

Prompt inhibition of fMLP-induced Ca2+ mobilization by parenteral lipid emulsions in human neutrophils.

PubMed

Wanten, Geert; Rops, Angelique; van Emst-De Vries, Sjenet E; Naber, Ton; Willems, Peter H G M

2002-04-01

It remains unclear whether modulation of immune system functions by lipids contributes to the increased infection rate observed in patients treated with parenteral nutrition. We therefore evaluated the effects of lipid emulsions derived from fish oil [very long chain triglycerides (VLCT)], olive oil [long-chain triglycerides- mono-unsaturated fatty acid (LCT-MUFA)], soya oil [long-chain triglycerides (LCT)], or a physical mixture of coconut and soya oil [mixed long- and medium-chain triglycerides (LCT-MCT)] on neutrophil activation. N-formyl-methionyl-leucyl-phenylalanine (fMLP) evoked an immediate increase of the cytosolic Ca2+ concentration ([Ca2+](i,av)) in a suspension of neutrophils. When added 3 min before fMLP, however, all four lipid emulsions reduced the hormone-induced increase in [Ca2+](i,av) with the same efficacy but with different potency. Half-maximal inhibition was reached at emulsion concentrations of 0.24 mM VLCT, 0.32 mM LCT-MCT, 0.52 mM LCT, and 0.82 mM LCT-MUFA. Similarly to the lipids, the protein kinase C (PKC) activator PMA markedly reduced the fMLP-induced increase in [Ca2+](i,av). PMA inhibition was abolished by the PKC inhibitor staurosporine. In contrast, however, this drug did not interfere with the inhibitory lipid effect, indicating that the lipids act primarily in a PKC-independent manner. In summary, this study shows that nutritional lipids can evoke a prompt and significant attenuation of hormone-induced neutrophil stimulation and that the emulsions based on fish oil and a mixture of coconut oil and soya oil are among the most potent ones in this respect.

Dietary medium-chain triglycerides promote oral allergic sensitization and orally induced anaphylaxis to peanut protein in mice

PubMed Central

Li, Jianing; Wang, Yu; Tang, Lihua; de Villiers, Willem JS; Cohen, Donald; Woodward, Jerold; Finkelman, Fred D; Eckhardt, Erik RM

2012-01-01

BACKGROUND The prevalence of peanut allergies is rising. Peanuts and many other allergen sources contain significant amounts of triglycerides, which affect absorption of antigens but have unknown effects on sensitization and anaphylaxis. We recently reported that dietary medium-chain triglycerides (MCT), which bypass mesenteric lymph and directly enter portal blood, reduce intestinal antigen absorption into blood compared to long-chain triglycerides (LCT), which stimulate mesenteric lymph flow and are absorbed in chylomicrons via mesenteric lymph. OBJECTIVE Test how dietary MCT affect food allergy. METHODS C3H/HeJ mice were fed peanut butter protein in MCT, LCT (peanut oil), or LCT plus an inhibitor of chylomicron formation (Pluronic L81; “PL81”). Peanut-specific antibodies in plasma, responses of the mice to antigen challenges, and intestinal epithelial cytokine expression were subsequently measured. RESULTS MCT suppressed antigen absorption into blood, but stimulated absorption into Peyer's patches. A single gavage of peanut protein with MCT as well as prolonged feeding in MCT-based diets caused spontaneous allergic sensitization. MCT-sensitized mice experienced IgG-dependent anaphylaxis upon systemic challenge and IgE-dependent anaphylaxis upon oral challenge. MCT feeding stimulated jejunal-epithelial TSLP, IL-25 and IL-33 expression compared to LCT, and promoted Th2 cytokine responses in splenocytes. Moreover, oral challenges of sensitized mice with antigen in MCT significantly aggravated anaphylaxis compared to challenges with LCT. Importantly, effects of MCT could be mimicked by adding PL81 to LCT, and in vitro assays indicated that chylomicrons prevent basophil activation. CONCLUSION Dietary MCT promote allergic sensitization and anaphylaxis by affecting antigen absorption and availability and by stimulating Th2 responses. PMID:23182172

Life cycle thinking in impact assessment—Current practice and LCA gains

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bidstrup, Morten, E-mail: Bidstrup@plan.aau.dk

It has been advocated that life cycle thinking (LCT) should be applied in impact assessment (IA) to a greater extent, since some development proposals pose a risk of significant impacts throughout the interconnected activities of product systems. Multiple authors have proposed the usage of life cycle assessment (LCA) for such analytical advancement, but little to no research on this tool application has been founded in IA practice so far. The aim of this article is to elaborate further on the gains assigned to application of LCA. The research builds on a review of 85 Danish IA reports, which were analysedmore » for analytical appropriateness and application of LCT. Through a focus on the non-technical summary, the conclusion and the use of specific search words, passages containing LCT were searched for in each IA report. These passages were then analysed with a generic framework. The results reveal that LCT is appropriate for most of the IAs, but that LCA is rarely applied to provide such a perspective. Without LCA, the IAs show mixed performance in regard to LCT. Most IAs do consider the product provision of development proposals, but they rarely relate impacts to this function explicitly. Many IAs do consider downstream impacts, but assessments of upstream, distant impacts are generally absent. It is concluded that multiple analytical gains can be attributed to greater application of LCA in IA practice, though some level of LCT already exists. - Highlights: • Life cycle thinking is appropriate across the types and topics of impact assessment. • Yet, life cycle assessment is rarely used for adding such perspective. • Impact assessment practice does apply some degree of life cycle thinking. • However, application of life cycle assessment could bring analytical gains.« less

The Leganés cognitive test correlates poorly with MRI evidence of global cortical atrophy in an underserved community: A population-based and nested case-control study in rural Ecuador (The Atahualpa Project)

PubMed Central

Brutto, Oscar H. Del; Mera, Robertino M; Zambrano, Mauricio; Lama, Julio

2014-01-01

Objective We aimed to evaluate whether the Leganés cognitive test (LCT) correlates with global cortical atrophy (GCA) and can be used as a surrogate for structural brain damage. Methods Atahualpa residents aged > 60 years identified during a door-to-door survey underwent MRI for grading GCA. Using multivariate generalized linear models, we evaluated whether continuous LCT scores correlated with GCA, after adjusting for demographics, education, cardiovascular health (CVH) status, depression and edentulism. In a nested case-control study, GCA severity was assessed in subjects with LCT scores below the cutoff level for dementia (< 22 points) and in matched controls without dementia. Results Out of 311 eligible subjects, 241 (78%) were enrolled. Mean age was 69.2±7.5 years, 59% were women, 83% had primary school education, 73% had poor CVH status, 12% had symptoms of depression and 43% had edentulism. Average LCT score was 26.7±3, and 23 (9.5%) subjects scored < 22 points. GCA was mild in 108, moderate in 95, and severe in 26 individuals. On the multivariate model, mean LCT score was not associated with GCA severity (β=0.06, SE=0.34, p=0.853). Severe GCA was noted in 6 / 23 case-patients and in 8 / 23 controls (OR: 0.67, 95% CI: 0.14-2.81, p=0.752, McNemar's test). Conclusion The LCT does not correlate with severity of GCA after adjusting for potential confounding variables, and should not be used as a reliable estimate of structural brain damage. PMID:29213925

The Leganés cognitive test correlates poorly with MRI evidence of global cortical atrophy in an underserved community: A population-based and nested case-control study in rural Ecuador (The Atahualpa Project).

PubMed

Brutto, Oscar H Del; Mera, Robertino M; Zambrano, Mauricio; Lama, Julio

2014-01-01

We aimed to evaluate whether the Leganés cognitive test (LCT) correlates with global cortical atrophy (GCA) and can be used as a surrogate for structural brain damage. Atahualpa residents aged > 60 years identified during a door-to-door survey underwent MRI for grading GCA. Using multivariate generalized linear models, we evaluated whether continuous LCT scores correlated with GCA, after adjusting for demographics, education, cardiovascular health (CVH) status, depression and edentulism. In a nested case-control study, GCA severity was assessed in subjects with LCT scores below the cutoff level for dementia (< 22 points) and in matched controls without dementia. Out of 311 eligible subjects, 241 (78%) were enrolled. Mean age was 69.2±7.5 years, 59% were women, 83% had primary school education, 73% had poor CVH status, 12% had symptoms of depression and 43% had edentulism. Average LCT score was 26.7±3, and 23 (9.5%) subjects scored < 22 points. GCA was mild in 108, moderate in 95, and severe in 26 individuals. On the multivariate model, mean LCT score was not associated with GCA severity (β=0.06, SE=0.34, p=0.853). Severe GCA was noted in 6 / 23 case-patients and in 8 / 23 controls (OR: 0.67, 95% CI: 0.14-2.81, p=0.752, McNemar's test). The LCT does not correlate with severity of GCA after adjusting for potential confounding variables, and should not be used as a reliable estimate of structural brain damage.

Normal anti-Klebsiella lymphocytotoxicity in ankylosing spondylitis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kinsella, T.D.; Fritzler, M.J.; Lewkonia, R.M.

1986-03-01

We compared in vitro lymphocytotoxicity (LCT) of peripheral blood lymphocytes (PBL), obtained from patients with ankylosing spondylitis (AS) and normal controls (NC). Assays were performed with antibacterial antisera prepared from AS- and NC-derived Klebsiella and coliforms Escherichia coli. LCT assessed by eosin staining was not significantly different in PBL of 12 AS patients and 28 controls when reacted with 3 Klebsiella and 1 E coli antisera. LCT assessed by /sup 51/Cr release was not significantly different for PBL of 20 age- and sex-matched pairs of AS patients and NC when reacted with 3 Klebsiella and 1 E coli antisera. Similarly,more » LCT-/sup 51/Cr of PBL of 15 matched AS and NC pairs was not significantly different for anti-K21, a serotype putatively implicated in Klebsiella-HLA-B27 antigenic cross-reactivity. Our results do not support the notion of molecular mimicry between Klebsiella and B27 in the pathogenesis of primary AS.« less

Enantiomeric separation of type I and type II pyrethroid insecticides with different chiral stationary phases by reversed-phase high-performance liquid chromatography.

PubMed

Zhang, Ping; Yu, Qian; He, Xiulong; Qian, Kun; Xiao, Wei; Xu, Zhifeng; Li, Tian; He, Lin

2018-04-01

The enantiomeric separation of type I (bifenthrin, BF) and type II (lambda-cyhalothrin, LCT) pyrethroid insecticides on Lux Cellulose-1, Lux Cellulose-3, and Chiralpak IC chiral columns was investigated by reversed-phase high-performance liquid chromatography. Methanol/water or acetonitrile/water was used as mobile phase at a flow rate of 0.8 mL/min. The effects of chiral stationary phase, mobile phase composition, column temperature, and thermodynamic parameters on enantiomer separation were carefully studied. Bifenthrin got a partial separation on Lux Cellulose-1 column and baseline separation on Lux Cellulose-3 column, while LCT enantiomers could be completely separated on both Lux Cellulose-1 and Lux Cellulose-3 columns. Chiralpak IC provided no separation ability for both BF and LCT. Retention factor (k) and selectivity factor (α) decreased with the column temperature increasing from 10°C to 40°C for both BF and LCT enantiomers. Thermodynamic parameters including ∆H and ∆S were also calculated, and the maximum R s were not always obtained at lowest temperature. Furthermore, the quantitative analysis methods for BF and LCT enantiomers in soil and water were also established. Such results provide a new approach for pyrethroid separation under reversed-phase condition and contribute to environmental risk assessment of pyrethroids at enantiomer level. © 2017 Wiley Periodicals, Inc.

Randomized clinical trial of new intravenous lipid (SMOFlipid 20%) versus medium-chain triglycerides/long-chain triglycerides in adult patients undergoing gastrointestinal surgery.

PubMed

Wu, Ming-Hsun; Wang, Ming-Yang; Yang, Chin-Yao; Kuo, Min-Liang; Lin, Ming-Tsan

2014-09-01

SMOFlipid 20% is intravenous lipid emulsion (ILE) containing long-chain triglycerides (LCT), medium-chain triglycerides (MCT), olive oil, and fish oil as a mixed emulsion containing α-tocopherol. The aim was to assess the efficacy of this new ILE in gastrointestinal surgery compared with MCT/LCT. In this prospective study, 40 patients were randomized to SMOFlipid 20% or MCT/LCT (Lipovenoes 20%) group. Clinical and biochemistry data were collected. Inflammatory markers (CRP, IL-6, IL-10, TNF-α, TGF-β1) and oxidative stress (ROS and superoxide) were measured. Thirty-five patients (17 males and 18 females) with a mean age of 57 years completed the study. The patients' demographic characteristics (age, gender, height, body weight, and BMI) were similar without significant differences between groups. The increment of triglyceride on day 6 from baseline was significantly lower in SMOFlipid group than in Lipovenoes MCT/LCT group. Inflammatory markers, as well as superoxide radical and total oxygen radical were not different between groups. Despite the comparable effect on inflammatory response, because of its well-balanced fatty acid pattern, relatively low n-6:n-3 ratio, and high vitamin E content, SMOFlipid had a better triglyceride-lowering effect as compared with MCT/LCT in adult patients undergoing gastrointestinal surgery. © 2013 American Society for Parenteral and Enteral Nutrition.

Analgesic efficacy of lysine clonixinate plus tramadol versus tramadol in multiple doses following impacted third molar surgery.

PubMed

Perez-Urizar, J; Martínez-Rider, R; Torres-Roque, I; Garrocho-Rangel, A; Pozos-Guillen, A

2014-03-01

This study compared the analgesic and anti-inflammatory efficacy, trismus control, and tolerability of the combination of lysine clonixinate and tramadol (LCT) versus tramadol (T) alone after surgical removal of impacted mandibular third molars. This study was a double-blind, randomized clinical trial, including two study groups of 20 patients each, who exhibited acute pain subsequent to surgical extraction of two mandibular third molars. Pain intensity was quantified over a 96-h period using a visual analogue scale and a 5-point verbal rating scale. Secondary indicators of analgesic and anti-inflammatory efficacy, trismus control, and tolerability were determined. Patients administered LCT exhibited better therapeutic effects that those administered T. Fifty percent of patients in the LCT group rated this therapy as 'excellent analgesia' compared with only 10% in the T group. The onset of the analgesic effect of LCT was significantly faster, without any therapeutic failures. There were no significant differences between the groups with regard to anti-inflammatory effect or trismus. The results of this study suggest that the postsurgical analgesic efficacy of LCT in combination (LC 125 mg + T 25 mg) is superior to that obtained with T alone, administered at the standard dose of 50 mg, for up to 96 h after the extraction of both impacted mandibular third molars. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

NMR-based metabolomics approach to study the toxicity of lambda-cyhalothrin to goldfish (Carassius auratus).

PubMed

Li, Minghui; Wang, Junsong; Lu, Zhaoguang; Wei, Dandan; Yang, Minghua; Kong, Lingyi

2014-01-01

In this study, a (1)H nuclear magnetic resonance (NMR) based metabolomics approach was applied to investigate the toxicity of lambda-cyhalothrin (LCT) in goldfish (Carassius auratus). LCT showed tissue-specific damage to gill, heart, liver and kidney tissues of goldfish. NMR profiling combined with statistical methods such as orthogonal partial least squares discriminant analysis (OPLS-DA) and two-dimensional statistical total correlation spectroscopy (2D-STOCSY) was developed to discern metabolite changes occurring after one week LCT exposure in brain, heart and kidney tissues of goldfish. LCT exposure influenced levels of many metabolites (e.g., leucine, isoleucine and valine in brain and kidney; lactate in brain, heart and kidney; alanine in brain and kidney; choline in brain, heart and kidney; taurine in brain, heart and kidney; N-acetylaspartate in brain; myo-inositol in brain; phosphocreatine in brain and heart; 2-oxoglutarate in brain; cis-aconitate in brain, and etc.), and broke the balance of neurotransmitters and osmoregulators, evoked oxidative stress, disturbed metabolisms of energy and amino acids. The implication of glutamate-glutamine-gamma-aminobutyric axis in LCT induced toxicity was demonstrated for the first time. Our findings demonstrated the applicability and potential of metabolomics approach for the elucidation of toxicological effects of pesticides and the underlying mechanisms, and the discovery of biomarkers for pesticide pollution in aquatic environment. Copyright © 2013 Elsevier B.V. All rights reserved.

Nucleic acids encoding metal uptake transporters and their uses

DOEpatents

Schroeder, Julian I.; Antosiewicz, Danuta M.; Schachtman, Daniel P.; Clemens, Stephan

1999-01-01

The invention provides LCT1 nucleic acids which encode metal ion uptake transporters. The invention also provides methods of modulating heavy metal and alkali metal uptake in plants. The methods involve producing transgenic plants comprising a recombinant expression cassette containing an LCT1 nucleic acid linked to a plant promoter.

The metabolic consequences of infusing emulsions containing medium chain triglycerides for parenteral nutrition: a comparative study with conventional lipid.

PubMed Central

Dennison, A. R.; Ball, M.; Crowe, P. J.; White, K.; Hands, L.; Watkins, R. M.; Kettlewell, M.

1986-01-01

In order to test the hypothesis that medium chain triglycerides (MCT's) are a safe and potentially superior energy source during parenteral nutrition 13 patients were entered into a randomised cross over trial. They received either a long chain triglyceride emulsion (LCT) or a 50% medium chain (MCT)/50% LCT mixture as part of their energy supply. Nitrogen balance was significantly better when MCT/LCT was infused and the greater levels of plasma ketones and lower plasma triglyceride levels suggested that MCT was more readily metabolised in these patients. Routine haematology, biochemistry and liver function tests gave no indication of harmful side effects from MCT. PMID:3089123

Creating a Learner-Centered Teaching Environment Using Student Choice in Assignments

ERIC Educational Resources Information Center

Hanewicz, Cheryl; Platt, Angela; Arendt, Anne

2017-01-01

Learner-centered teaching (LCT) has been found to be a more effective pedagogy for online students, as traditional teaching methods do not work well in online courses. Professors in an upper-level technology management class revised their online introductory course to incorporate cafeteria-style grading. This LCT approach allowed students to…

Polymerization and processing of polymers in magnetic fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benicewicz, B.C.; Smith, M.E.; Douglas, E.P.

1997-04-01

Liquid crystalline thermosets (LCT`s) have become recognized over the past few years as an important class of materials. Numerous reports from the authors laboratory and others have described their synthesis and phase behavior. In particular, the authors have described important effects due to the orientation of the rodlike molecules in a liquid crystalline phase. They have found that curing rates are enhanced compared to reaction in an isotropic phase, and that the glass transition of the fully cured material can be significantly higher than the final cure temperature. For structural applications, orientation of LCT`s will allow maximum improvement in mechanicalmore » properties. A few studies have described use of magnetic fields to orient LCT`s. However, no measurements were made of the tensile properties of materials processed in magnetic fields. The authors have conducted experiments which describe the tensile modulus dependence of an LCT over the complete range of magnetic field strengths from 0 to 18 Tesla. Their work has focused on the system composed of the diglycidyl ether of dihydroxy-{alpha}-methylstilbene (DGE-DHAMS) cured with sulfanilamide (SAA).« less

Randomized Trial Comparing Amniotic Membrane Transplantation with Lamellar Corneal Graft for the Treatment of Corneal Thinning.

PubMed

de Farias, Charles C; Allemann, Norma; Gomes, José Á P

2016-04-01

There are few studies comparing different surgical procedures for the treatment of corneal thinning. Lamellar corneal transplantation (LCT) has been reported to be efficient, but its results can be jeopardized by allograft rejection, opacification, or high astigmatism. Amniotic membrane transplantation (AMT) has been considered a good alternative, but it is not as resistant as LCT and the tissue can be reabsorbed after surgery. A prospective, randomized, interventional, and comparative study of consecutive patients with corneal thinning over 6 months was performed. Ophthalmological examination was performed before transplant surgery and then repeated 1, 7, 15, 30, 90, and 180 days after surgery and ultrasound biomicroscopy was performed before and then 30, 90, and 180 days after surgery to assess corneal thinning. Herpes simplex infection was the main cause of corneal thinning (9 eyes), followed by surgery (cataract, glaucoma, 5 cases), rheumatoid arthritis (1), chemical burn (1), perforating trauma (1), previous band keratopathy treatment (1), and Stevens-Johnson syndrome (1). Although all patients showed significant increase in final thickness in the area of thinning, it was higher in those submitted to LCT at 180 days postoperatively. Regardless of the surgical technique, all patients showed epithelialization. Patients undergoing AMT showed an 89% decrease in neovascularization. Final corrected distance visual acuity was better in patients submitted to AMT. LCT proved to be the best option for treating corneal thinning. AMT represents an alternative that allows good visual recovery but does not restore corneal thickness as efficiently as LCT.

Several Different Lactase Persistence Associated Alleles and High Diversity of the Lactase Gene in the Admixed Brazilian Population

PubMed Central

Friedrich, Deise C.; Santos, Sidney E. B.; Ribeiro-dos-Santos, Ândrea K. C.; Hutz, Mara H.

2012-01-01

Adult-type hypolactasia is a common phenotype caused by the lactase enzyme deficiency. The −13910 C>T polymorphism, located 14 Kb upstream of the lactase gene (LCT) in the MCM6 gene was associated with lactase persistence (LP) in Europeans. This polymorphism is rare in Africa but several other variants associated with lactase persistence were observed in Africans. The aims of this study were to identify polymorphisms in the MCM6 region associated with the lactase persistence phenotype and to determine the distribution of LCT gene haplotypes in 981 individuals from North, Northeast and South Brazil. These polymorphisms were genotyped by PCR based methods and sequencing. The −13779*C,−13910*T, −13937*A, −14010*C, −14011*T LP alleles previously described in the MCM6 gene region that acts as an enhancer for the LCT gene were identified in Brazilians. The most common LP allele was −13910*T. Its frequency was highly correlated with European ancestry in the Brazilian populations investigated. The −13910*T was higher (0.295) in southern Brazilians of European ancestry and lower (0.175) in the Northern admixed population. LCT haplotypes were derived from the 10 LCT SNPs genotyped. Overall twenty six haplotypes previously described were identified in the four Brazilian populations studied. The Multidimensional Scaling analysis showed that Belém, in the north, was closer to Amerindians. Northeastern and southern Afro-descendants were more related with Bantu-speaking South Africans whereas the Southern population with European ancestry grouped with Southern and Northern Europeans. This study shows a high variability considering the number of LCT haplotypes observed. Due to the highly admixed nature of the Brazilian populations, the diagnosis of hypolactasia in Brazil, based only in the investigation of the −13910*T allele is an oversimplification. PMID:23029545

COMPASS Final Report: Lunar Relay Satellite (LRS)

NASA Technical Reports Server (NTRS)

Oleson, Steven R.; McGuire, Melissa L.

2012-01-01

The Lunar Relay Satellite (LRS) COllaborative Modeling and Parametric Assessment of Space Systems (COMPASS) session was tasked to design a satellite to orbit in an elliptical lunar polar orbit to provide relay communications between lunar South Pole assets and the Earth. The design included a complete master equipment list, power requirement list, configuration design, and brief risk assessment and cost analysis. The LRS is a half-TDRSS sized box spacecraft, which provides communications and navigation relay between lunar outposts (via Lunar Communications Terminals (LCT)) or Sortie parties (with user radios) and large ground antennas on Earth. The LRS consists of a spacecraft containing all the communications and avionics equipment designed by NASA Jet Propulsion Laboratory s (JPL) Team X to perform the relay between lunar-based assets and the Earth. The satellite design is a standard box truss spacecraft design with a thermal control system, 1.7 m solar arrays for 1 kWe power, a 1 m diameter Ka/S band dish which provides relay communications with the LCT, and a Q-band dish for communications to/from the Earth based assets. While JPL's Team X and Goddard Space Flight Center s (GSFC) I M Design Center (IMDC) have completed two other LRS designs, this NASA Glenn Research Center (GRC) COMPASS LRS design sits between them in terms of physical size and capabilities.

Genome Sequence of Pseudomonas aeruginosa Strain LCT-PA220, Which Was Selected after Space Flight by Using Biolog's Powerful Carbon Source Utilization Technology.

PubMed

Xu, Guogang; Hu, Juan; Fang, Xiangqun; Zhang, Xuelin; Wang, Junfeng; Guo, Yinghua; Li, Tianzhi; Chen, Zhenghong; Dai, Wenkui; Liu, Changting

2014-03-13

To explore the changes of Pseudomonas aeruginosa in space flight, we present the draft genome sequence of P. aeruginosa strain LCT-PA220, which originated from a P. aeruginosa strain, ATCC 27853, that traveled on the Shenzhou-VIII spacecraft.

Lipid emulsions differentially affect LPS-induced acute monocytes inflammation: in vitro effects on membrane remodeling and cell viability.

PubMed

Boisramé-Helms, Julie; Delabranche, Xavier; Klymchenko, Andrey; Drai, Jocelyne; Blond, Emilie; Zobairi, Fatiha; Mely, Yves; Hasselmann, Michel; Toti, Florence; Meziani, Ferhat

2014-11-01

The aim of this study was to assess how lipid emulsions for parenteral nutrition affect lipopolysaccharide (LPS)-induced acute monocyte inflammation in vitro. An 18 h long LPS induced human monocyte leukemia cell stimulation was performed and the cell-growth medium was supplemented with three different industrial lipid emulsions: Intralipid(®), containing long-chain triglycerides (LCT--soybean oil); Medialipid(®), containing LCT (soybean oil) and medium-chain triglycerides (MCT--coconut oil); and SMOFlipid(®), containing LCT, MCT, omega-9 and -3 (soybean, coconut, olive and fish oils). Cell viability and apoptosis were assessed by Trypan blue exclusion and flow cytometry respectively. Monocyte composition and membrane remodeling were studied using gas chromatography and NR12S staining. Microparticles released in supernatant were measured by prothrombinase assay. After LPS challenge, both cellular necrosis and apoptosis were increased (threefold and twofold respectively) and microparticle release was enhanced (sevenfold) after supplementation with Medialipid(®) compared to Intralipid(®), SMOFlipid(®) and monocytes in the standard medium. The monocytes differentially incorporated fatty acids after lipid emulsion challenge. Finally, lipid-treated cells displayed microparticles characterized by disrupted membrane lipid order, reflecting lipid remodeling of the parental cell plasma membrane. Our data suggest that lipid emulsions differentially alter cell viability, monocyte composition and thereby microparticle release. While MCT have deleterious effects, we have shown that parenteral nutrition emulsion containing LCT or LCT and MCT associated to n-3 and n-9 fatty acids have no effect on endotoxin-induced cell death and inflammation.

Lipid Emulsions Containing Medium Chain Triacylglycerols Blunt Bradykinin-Induced Endothelium-Dependent Relaxation in Porcine Coronary Artery Rings.

PubMed

Amissi, Said; Boisramé-Helms, Julie; Burban, Mélanie; Rashid, Sherzad K; León-González, Antonio J; Auger, Cyril; Toti, Florence; Meziani, Ferhat; Schini-Kerth, Valérie B

2017-03-01

Lipid emulsions for parenteral nutrition are used to provide calories and essential fatty acids for patients. They have been associated with hypertriglyceridemia, hypercholesterolemia, and metabolic stress, which may promote the development of endothelial dysfunction in patients. The aim of the present study was to determine whether five different industrial lipid emulsions may affect the endothelial function of coronary arteries. Porcine coronary artery rings were incubated with lipid emulsions 0.5, 1, or 2% (v/v) for 30 min before the determination of vascular reactivity in organ chambers and the level of oxidative stress using electron paramagnetic resonance. Incubation of coronary artery rings with either Lipidem ® , Medialipid ® containing long- and medium-chain triacylglycerols (LCT/MCT), or SMOFlipid ® containing LCT, MCT, omega-9, and -3, significantly reduced the bradykinin-induced endothelium-dependent relaxation, affecting both the nitric oxide (NO) and endothelium-dependent hyperpolarization (EDH) components, whereas, Intralipid ® containing LCT (soybean oil) and ClinOleic ® containing LCT (soybean and olive oil) did not have such an effect. The endothelial dysfunction induced by Lipidem ® was significantly improved by indomethacin, a cyclooxygenase (COX) inhibitor, inhibitors of oxidative stress (N-acetylcysteine, superoxide dismutase, catalase) and transition metal chelating agents (neocuproine, tetrathiomolybdate, deferoxamine and L-histidine). Lipidem ® significantly increased the arterial level of oxidative stress. The present findings indicate that lipid emulsions containing LCT/MCT induce endothelial dysfunction in coronary artery rings by blunting both NO- and EDH-mediated relaxations. The Lipidem ® -induced endothelial dysfunction is associated with increased vascular oxidative stress and the formation of COX-derived vasoconstrictor prostanoids.

Naloxegol, an opioid antagonist with reduced CNS penetration: Mode-of-action and human relevance for rat testicular tumours.

PubMed

Andersson, Håkan; Mitchard, Terri; Johnson, Nakpangi; Floettmann, Eike

2017-08-15

Naloxegol is an opioid antagonist which has been developed for the treatment of patients with opioid induced constipation. In the nonclinical safety program naloxegol was shown to have a very benign toxicity profile. In the rat, but not the mouse, 2-year carcinogenicity study a change in tumour pattern with an increase in testicular Leydig cell tumours (LCT) was observed after dosing at high (supra-pharmacological) concentrations. To establish the basis of the increase in LCT and to assess its potential relevance to humans, studies to exclude and potentially identify mode-of-action (MoA) were performed. A genotoxic mechanism was ruled out following negative results in the Ames, mouse lymphoma, and micronucleus assays. An effect on androgen metabolism was excluded since the treatment of rats with naloxegol for 14days did not result in any induction of CYP protein levels. It was demonstrated that administration of centrally restricted opioid antagonists naloxegol or methylnaltrexone at high doses induced an increase in LH release with no clear increase in testosterone, in contrast to the centrally acting opioid antagonist naloxone, which showed marked increases in both LH and testosterone. LCT due to increased LH stimulation is common in rats but not documented in humans. Collectively, the lack of genotoxicity signal, the lack of androgen effect, the increase in LH secretion in rats, which is no considered to be relevant for LCT formation in humans, and high margins to clinical exposures, the observed increase in LCT in the rat is not expected to be clinically relevant. Copyright © 2017 Elsevier Inc. All rights reserved.

Mineral-deposit model for lithium-cesium-tantalum pegmatites

USGS Publications Warehouse

Bradley, Dwight C.; McCauley, Andrew D.; Stillings, Lisa L.

2017-06-20

Lithium-cesium-tantalum (LCT) pegmatites comprise a compositionally defined subset of granitic pegmatites. The major minerals are quartz, potassium feldspar, albite, and muscovite; typical accessory minerals include biotite, garnet, tourmaline, and apatite. The principal lithium ore minerals are spodumene, petalite, and lepidolite; cesium mostly comes from pollucite; and tantalum mostly comes from columbite-tantalite. Tin ore as cassiterite and beryllium ore as beryl also occur in LCT pegmatites, as do a number of gemstones and high-value museum specimens of rare minerals. Individual crystals in LCT pegmatites can be enormous: the largest spodumene was 14 meters long, the largest beryl was 18 meters long, and the largest potassium feldspar was 49 meters long.Lithium-cesium-tantalum pegmatites account for about one-fourth of the world’s lithium production, most of the tantalum production, and all of the cesium production. Giant deposits include Tanco in Canada, Greenbushes in Australia, and Bikita in Zimbabwe. The largest lithium pegmatite in the United States, at King’s Mountain, North Carolina, is no longer being mined although large reserves of lithium remain. Depending on size and attitude of the pegmatite, a variety of mining techniques are used, including artisanal surface mining, open-pit surface mining, small underground workings, and large underground operations using room-and-pillar design. In favorable circumstances, what would otherwise be gangue minerals (quartz, potassium feldspar, albite, and muscovite) can be mined along with lithium and (or) tantalum as coproducts.Most LCT pegmatites are hosted in metamorphosed supracrustal rocks in the upper greenschist to lower amphibolite facies. Lithium-cesium-tantalum pegmatite intrusions generally are emplaced late during orogeny, with emplacement being controlled by pre-existing structures. Typically, they crop out near evolved, peraluminous granites and leucogranites from which they are inferred to be derived by fractional crystallization. In cases where a parental granite pluton is not exposed, one is inferred to lie at depth. Lithium-cesium-tantalum LCT pegmatite melts are enriched in fluxing components including H2O, F, P, and B, which depress the solidus temperature, lower the density, and increase rates of ionic diffusion. This, in turn, enables pegmatites to form thin dikes and massive crystals despite having a felsic composition and temperatures that are significantly lower than ordinary granitic melts. Lithium-cesium-tantalum pegmatites crystallized at remarkably low temperatures (about 350–550 °C) in a remarkably short time (days to years).Lithium-cesium-tantalum pegmatites form in orogenic hinterlands as products of plate convergence. Most formed during collisional orogeny (for example, Kings Mountain district, North Carolina). Specific causes of LCT pegmatite-related magmatism could include: ordinary arc processes; over thickening of continental crust during collision or subduction; slab breakoff during or after collision; slab delamination before, during, or after collision; and late collisional extensional collapse and consequent decompression melting. Lithium-cesium-tantalum pegmatite deposits are present in all continents including Antarctica and in rocks spanning 3 billion years of Earth history. The global age distribution of LCT pegmatites is similar to those of common pegmatites, orogenic granites, and detrital zircons. Peak times of LCT pegmatite genesis at about 2640, 1800, 960, 485, and 310 Ma (million years before present) correspond to times of collisional orogeny and supercontinent assembly. Between these pulses were long intervals when few or no LCT pegmatites formed. These minima overlap with supercontinent tenures at ca. 2450–2225, 1625–1000, 875–725, and 250–200 Ma.Exploration and assessment for LCT pegmatites are guided by a number of observations. In frontier areas where exploration has been minimal at best, the key first-order criteria are an orogenic hinterland setting, appropriate regional metamorphic grades, and the presence of evolved granites and common granitic pegmatites. New LCT pegmatites are most likely to be found near known deposits. Pegmatites tend to show a regional mineralogical and geochemical zoning pattern with respect to the inferred parental granite, with the greatest enrichment in the more distal pegmatites. Mineral-chemical trends in common pegmatites that can point toward an evolved LCT pegmatite include: increasing rubidium in potassium feldspar, increasing lithium in white mica, increasing manganese in garnet, and increasing tantalum and manganese in columbite-tantalite. Most LCT pegmatite bodies show a distinctive internal zonation featuring four zones: border, wall, intermediate (where lithium, cesium, and tantalum are generally concentrated), and core. This zonation is expressed both in cross section and map view; thus, what may appear to be a common pegmatite may instead be the edge of a mineralized body.Neither lithium-cesium-tantalum pegmatites nor their parental granites are likely to cause serious environmental concerns. Soils and country rock surrounding a LCT pegmatite, as well as waste from mining operations, may be enriched in characteristic elements relative to global average soil and bedrock values. These elements may include lithium, cesium, tantalum, beryllium, boron, fluorine, phosphorus, manganese, gallium, rubidium, niobium, tin, and hafnium. Among this suite of elements, however, the only ones that might present a concern for environmental health are beryllium and fluorine, which are included in the U.S. Environmental Protection Agency drinking-water regulations with maximum contaminant levels of 4 micrograms per liter and 4 milligrams per liter, respectively.

Influence of local capillary trapping on containment system effectiveness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bryant, Steven

2014-03-31

Immobilization of CO 2 injected into deep subsurface storage reservoirs is a critical component of risk assessment for geologic CO 2 storage (GCS). Local capillary trapping (LCT) is a recently established mode of immobilization that arises when CO 2 migrates due to buoyancy through heterogeneous storage reservoirs. This project sought to assess the amount and extent of LCT expected in storage formations under a range of injection conditions, and to confirm the persistence of LCT if the seal overlying the reservoir were to lose its integrity. Numerical simulation using commercial reservoir simulation software was conducted to assess the influence ofmore » injection. Laboratory experiments, modeling and numerical simulation were conducted to assess the effect of compromised seal integrity. Bench-scale (0.6 m by 0.6 m by 0.03 m) experiments with surrogate fluids provided the first empirical confirmation of the key concepts underlying LCT: accumulation of buoyant nonwetting phase at above residual saturations beneath capillary barriers in a variety of structures, which remains immobile under normal capillary pressure gradients. Immobilization of above-residual saturations is a critical distinction between LCT and the more familiar “residual saturation trapping.” To estimate the possible extent of LCT in a storage reservoir an algorithm was developed to identify all potential local traps, given the spatial distribution of capillary entry pressure in the reservoir. The algorithm assumes that the driving force for CO 2 migration can be represented as a single value of “critical capillary entry pressure” P c,entry crit, such that cells with capillary entry pressure greater/less than P c,entry crit act as barriers/potential traps during CO 2 migration. At intermediate values of P c,entry crit, the barrier regions become more laterally extensive in the reservoir, approaching a percolation threshold while non-barrier regions remain numerous. The maximum possible extent of LCT thus occurs at P c,entry crit near this threshold. Testing predictions of this simple algorithm against full-physics simulations of buoyancy-driven CO 2 migration support the concept of critical capillary entry pressure. However, further research is needed to determine whether a single value of critical capillary entry pressure always applies and how that value can be determined a priori. Simulations of injection into high-resolution (cells 0.3 m on a side) 2D and 3D heterogeneous domains show two characteristic behaviors. At small gravity numbers (vertical flow velocity much less than horizontal flow velocity) the CO 2 fills local traps as well as regions that would act as local barriers if CO 2 were moving only due to buoyancy. When injection ceases, the CO 2 migrates vertically to establish large saturations within local traps and residual saturation elsewhere. At large gravity numbers, the CO 2 invades a smaller portion of the perforated interval. Within this smaller swept zone the local barriers are not invaded, but local traps are filled to large saturation during injection and remain during post-injection gravity-driven migration. The small gravity number behavior is expected in the region within 100 m of a vertical injection well at anticipated rates of injection for commercial GCS. Simulations of leakage scenarios (through-going region of large permeability imposed in overlying seal) indicate that LCT persists (i.e. CO 2 remains held in a large fraction of the local iv traps) and the persistence is independent of injection rate during storage. Simulations of leakage for the limiting case of CO 2 migrating vertically from an areally extensive emplacement in the lower portion of a reservoir showed similar strong persistence of LCT. This research has two broad implications for GCS. The first is that LCT can retain a significant fraction of the CO 2 stored in a reservoir – above and beyond the residual saturation -- if the overlying seal were to fail. Thus frameworks for risk assessment should be extended to account for LCT. The second implication is that compared to pressure driven flow in reservoirs, CO 2 migration and trapping behave in a qualitatively different manner in heterogeneous reservoirs when buoyancy is the dominant driving force for flow. Thus simulations of GCS that neglect capillary heterogeneity will fail to capture important features of the CO 2 plume. While commercial reservoir simulation software can account for fine scale capillary heterogeneity, it has not been designed to work efficiently with such domains, and no simulators can handle fine-scale resolution throughout the reservoir. A possible way to upscale the migration and trapping is to apply an “effective residual saturation” to coarse-scale grids. While the extent of overall immobilization can be correlated in this way, all coarser grids failed to capture the distance traveled by the migrating CO 2 for large gravity number. Thus it remains unclear how best to account for LCT in the routine simulation work-flow that will be needed for large-scale GCS. Alternatives meriting investigation include streamline methods, reduced-physics proxies (e.g. particle tracking), and biased invasion percolation algorithms, which are based on precisely the capillary heterogeneity essential for LCT.« less

Nitrogen sparing effect of structured triglycerides containing both medium-and long-chain fatty acids in critically ill patients; a double blind randomized controlled trial.

PubMed

Lindgren, B F; Ruokonen, E; Magnusson-Borg, K; Takala, J

2001-02-01

Patients with sepsis and trauma are characterised by hypermetabolism, insulin resistance and protein catabolism. Fat emulsions containing medium chain triglycerides have been suggested to be beneficial for these patients since medium chain fatty acids are a more readily available source of energy when compared to long chain fatty acids. The aim of this study was to compare a medium and long chain triglyceride emulsion consisting of structured triglycerides (ST) with a long chain triglyceride (LCT) emulsion in terms of effects on nitrogen balance, energy metabolism and safety. 30 ICU patients with sepsis or multiple injury received a fat emulsion with ST or 20% LCT (1.5 g triglycerides/kg body weight/day) as a component of total parenteral nutrition (TPN), for 5 days in a double blind randomised parallel group design. The main analysis was made on the 3 day per protocol population due to lack of patients at day 5. There were no differences in baseline characteristics of the two groups receiving either the LCT or the ST emulsion. The efficacy analysis was performed on the per protocol population (n=9 ST, n=11 LCT). There was a significant difference between the two treatments regarding daily nitrogen balances when the first 3 days were analysed P=0.0038). This resulted in an amelioration of the nitrogen balance on day 3 in the group on ST as compared to those on LCT (0.1+/-2.4 g vs -9.9+/-2.1 g P=0.01). The 3 day cumulative nitrogen balance was significantly better in the group receiving ST compared to those on LCT (-0.7+/-6.0 vs -16.7+/-3.9 P=0.03). This better cumulative nitrogen balance on day 3 was also preserved as a tendency (P=0.061) in the analysis of the intention to treat population, but on day 5 there was no significant difference (P=0.08). The ST emulsion was well tolerated and no difference was found compared to the LCT emulsion regarding respiratory quotient, energy expenditure, glucose or triglyceride levels during infusion. Administration of a structured triglyceride emulsion resulted in an amelioration of nitrogen balance despite no effect on energy expenditure in short term administration over 3 days to ICU patients when compared to a long chain triglyceride emulsion. No side effects linked to medium chain triglycerides were noted. Copyright 2001 Harcourt Publishers Ltd.

Dose specification for 192Ir high dose rate brachytherapy in terms of dose-to-water-in-medium and dose-to-medium-in-medium

NASA Astrophysics Data System (ADS)

Paiva Fonseca, Gabriel; Carlsson Tedgren, Åsa; Reniers, Brigitte; Nilsson, Josef; Persson, Maria; Yoriyaz, Hélio; Verhaegen, Frank

2015-06-01

Dose calculation in high dose rate brachytherapy with 192Ir is usually based on the TG-43U1 protocol where all media are considered to be water. Several dose calculation algorithms have been developed that are capable of handling heterogeneities with two possibilities to report dose: dose-to-medium-in-medium (Dm,m) and dose-to-water-in-medium (Dw,m). The relation between Dm,m and Dw,m for 192Ir is the main goal of this study, in particular the dependence of Dw,m on the dose calculation approach using either large cavity theory (LCT) or small cavity theory (SCT). A head and neck case was selected due to the presence of media with a large range of atomic numbers relevant to tissues and mass densities such as air, soft tissues and bone interfaces. This case was simulated using a Monte Carlo (MC) code to score: Dm,m, Dw,m (LCT), mean photon energy and photon fluence. Dw,m (SCT) was derived from MC simulations using the ratio between the unrestricted collisional stopping power of the actual medium and water. Differences between Dm,m and Dw,m (SCT or LCT) can be negligible (<1%) for some tissues e.g. muscle and significant for other tissues with differences of up to 14% for bone. Using SCT or LCT approaches leads to differences between Dw,m (SCT) and Dw,m (LCT) up to 29% for bone and 36% for teeth. The mean photon energy distribution ranges from 222 keV up to 356 keV. However, results obtained using mean photon energies are not equivalent to the ones obtained using the full, local photon spectrum. This work concludes that it is essential that brachytherapy studies clearly report the dose quantity. It further shows that while differences between Dm,m and Dw,m (SCT) mainly depend on tissue type, differences between Dm,m and Dw,m (LCT) are, in addition, significantly dependent on the local photon energy fluence spectrum which varies with distance to implanted sources.

Age of the Lava Creek supereruption and magma chamber assembly at Yellowstone based on 40Ar/39Ar and U-Pb dating of sanidine and zircon crystals

NASA Astrophysics Data System (ADS)

Vazquez, J. A.; Matthews, N. E.; Calvert, A. T.

2015-12-01

The last supereruption from the Yellowstone Plateau formed Yellowstone caldera and ejected the >1000 km3 of rhyolite that composes the Lava Creek Tuff (LCT). Tephra from the eruption blanketed much of the western United States, and is a key Quaternary chronostratigraphic marker, in particular for dating deposition of mid-Pleistocene glacial and pluvial deposits in western North America. We performed 40Ar/39Ar dating of single sanidines to delimit eruption age, and ion microprobe U-Pb and trace-element analyses of crystal faces on single zircons to characterize magmatic evolution and date near-eruption crystallization, as well as analyses of crystal interiors to date the interval of zircon crystallization. Sanidines from the two LCT members A and B yield an 40Ar/39Ar isochron date of 631 ± 4 ka (2σ). Crystal faces on zircons from both members yield a weighted mean 206Pb/238U date of 627 ± 6 ka (2σ) and have trace element concentrations that vary with eruptive stratigraphy. Zircon interiors yield a weighted mean 206Pb/238U date of 660 ± 6 ka, and reveal reverse and/or oscillatory zoning of trace element concentrations, with many crystals containing high-U concentrations and dark cathodoluminescence (CL) cores. These crystals with high-U cores are possibly sourced from 'defrosting' of melt-impregnated margins of the growing subvolcanic reservoir. LCT sanidines mirror the variation of zircon composition within the eruptive stratigraphy, with crystals from upper LCT-A and basal LCT-B having bright-CL rims with high Ba concentrations, suggesting late crystallization after addition of less evolved silicic magma. The occurrence of distal LCT in stratigraphic sequences marking the Marine Isotope Stage 16-15 transition supports the apparent eruption age of ca. 631 ka. These results reveal that Lava Creek zircons record episodic heating, renewed crystallization, and an overall up-temperature evolution for Yellowstone's subvolcanic reservoir in the 103-104 year interval before eruption.

Impact of medium and long chain triglycerides consumption on appetite and food intake in overweight men.

PubMed

St-Onge, M-P; Mayrsohn, B; O'Keeffe, M; Kissileff, H R; Choudhury, A R; Laferrère, B

2014-10-01

Medium chain triglycerides (MCT) enhance thermogenesis and may reduce food intake relative to long chain triglycerides (LCT). The goal of this study was to establish the effects of MCT on appetite and food intake and determine whether differences were due to differences in hormone concentrations. Two randomized, crossover studies were conducted in which overweight men consumed 20 g of MCT or corn oil (LCT) at breakfast. Blood samples were obtained over 3 h. In Study 1 (n=10), an ad lib lunch was served after 3 h. In Study 2 (n=7), a preload containing 10 g of test oil was given at 3 h and lunch was served 1 h later. Linear mixed model analyses were performed to determine the effects of MCT and LCT oil on change in hormones and metabolites from fasting, adjusting for body weight. Correlations were computed between differences in hormones just before the test meals and differences in intakes after the two oils for Study 1 only. Food intake at the lunch test meal after the MCT preload (Study 2) was (mean±s.e.m.) 532±389 kcal vs 804±486 kcal after LCT (P<0.05). MCT consumption resulted in a lower rise in triglycerides (P=0.014) and glucose (P=0.066) and a higher rise in peptide YY (PYY, P=0.017) and leptin (P=0.036) compared with LCT (combined data). Correlations between differences in hormone levels (glucagon-like peptide (GLP-1), PYY) and differences in food intake were in the opposite direction to expectations. MCT consumption reduced food intake acutely but this does not seem to be mediated by changes in GLP-1, PYY and insulin.

Four novel mutations in the lactase gene (LCT) underlying congenital lactase deficiency (CLD).

PubMed

Torniainen, Suvi; Freddara, Roberta; Routi, Taina; Gijsbers, Carolien; Catassi, Carlo; Höglund, Pia; Savilahti, Erkki; Järvelä, Irma

2009-01-22

Congenital lactase deficiency (CLD) is a severe gastrointestinal disorder of newborns. The diagnosis is challenging and based on clinical symptoms and low lactase activity in intestinal biopsy specimens. The disease is enriched in Finland but is also present in other parts of the world. Mutations encoding the lactase (LCT) gene have recently been shown to underlie CLD. The purpose of this study was to identify new mutations underlying CLD in patients with different ethnic origins, and to increase awareness of this disease so that the patients could be sought out and treated correctly. Disaccharidase activities in intestinal biopsy specimens were assayed and the coding region of LCT was sequenced from five patients from Europe with clinical features compatible with CLD. In the analysis and prediction of mutations the following programs: ClustalW, Blosum62, PolyPhen, SIFT and Panther PSEC were used. Four novel mutations in the LCT gene were identified. A single nucleotide substitution leading to an amino acid change S688P in exon 7 and E1612X in exon 12 were present in a patient of Italian origin. Five base deletion V565fsX567 leading to a stop codon in exon 6 was found in one and a substitution R1587H in exon 12 from another Finnish patient. Both Finnish patients were heterozygous for the Finnish founder mutation Y1390X. The previously reported mutation G1363S was found in a homozygous state in two siblings of Turkish origin. This is the first report of CLD mutations in patients living outside Finland. It seems that disease is more common than previously thought. All mutations in the LCT gene lead to a similar phenotype despite the location and/or type of mutation.

Impact of medium and long chain triglycerides consumption on appetite and food intake in overweight men

PubMed Central

St-Onge, Marie-Pierre; Mayrsohn, Brian; O’Keeffe, Majella; Kissileff, Harry R.; Choudhury, Arindam Roy; Laferrère, Blandine

2014-01-01

Background Medium chain triglycerides (MCT) enhance thermogenesis and may reduce food intake relative to long chain triglycerides (LCT). The goal of this study was to establish the effects of MCT on appetite and food intake and determine whether differences were due to differences in hormone concentrations. Methods Two randomized, crossover studies were conducted in which overweight men consumed 20 g of MCT or corn oil (LCT) at breakfast. Blood samples were obtained over 3 h. In Study 1 (n=10), an ad lib lunch was served after 3 h. In Study 2 (n=7), a pre-load containing 10 g of test oil was given at 3 h and lunch was served 1 h later. Linear mixed model analyses were performed to determine the effects of MCT and LCT oil on change in hormones and metabolites from fasting, adjusting for body weight. Correlations were computed between differences in hormones just before the test meals and differences in intakes after the two oils for Study 1 only. Results Food intake at the lunch test meal after the MCT pre-load (Study 2) was (mean ± SEM) 532 ± 389 kcal vs. 804 ± 486 kcal after LCT (P < 0.05). MCT consumption resulted in a lower rise in triglycerides (P = 0.014) and glucose (P = 0.066) and a higher rise in peptide YY (P = 0.017) and leptin (P = 0.036) compared to LCT (combined data). Correlations between differences in hormone levels (GLP-1, PYY) and differences in food intake were in the opposite direction to expectations. Conclusions MCT consumption reduced food intake acutely but this does not seem to be mediated by changes in GLP-1, PYY, and insulin. PMID:25074387

Frequency of LCT -13910C>T single nucleotide polymorphism associated with adult-type hypolactasia/lactase persistence among Brazilians of different ethnic groups.

PubMed

Mattar, Rejane; Monteiro, Maria S; Villares, Cibele A; Santos, Aníbal F; Silva, Joyce M K; Carrilho, Flair J

2009-10-02

Adult-type hypolactasia, the physiological decline of lactase some time after weaning, was previously associated with the LCT -13910C>T polymorphism worldwide except in Africa. Lactase non-persistence is the most common phenotype in humans, except in northwestern Europe with its long history of pastoralism and milking. We had previously shown association of LCT -13910C>T polymorphism with adult-type hypolactasia in Brazilians; thus, we assessed its frequency among different Brazilian ethnic groups. We investigated the ethnicity-related frequency of this polymorphism in 567 Brazilians [mean age, 42.1 +/- 16.8 years; 157 (27.7%) men]; 399 (70.4%) White, 50 (8.8%) Black, 65 (11.5%) Brown, and 53 (9.3%) Japanese-Brazilian. DNA was extracted from leukocytes; LCT -13910C>T polymorphism was analyzed by PCR-restriction fragment length polymorphism. Prevalence of the CC genotype associated with hypolactasia was similar (57%) among White and Brown groups; however, prevalence was higher among Blacks (80%) and those of Japanese descent (100%). Only 2 (4%) Blacks had TT genotype, and 8 (16%) had the CT genotype. Assuming an association between CC genotype and hypolactasia, and CT and TT genotypes with lactase persistence, 356 (62.8%) individuals had hypolactasia and 211 (37.2%) had lactase persistence. The White and Brown groups had the same hypolactasia prevalence (approximately 57%); nevertheless, was 80% among Black individuals and 100% among Japanese-Brazilians (P < 0.01). The lactase persistence allele, LCT -13910T, was found in about 43% of both White and Brown and 20% of the Black Brazilians, but was absent among all Japanese Brazilians studied.

Environmentally relevant levels of λ-cyhalothrin, fenvalerate, and permethrin cause developmental toxicity and disrupt endocrine system in zebrafish (Danio rerio) embryo.

PubMed

Zhang, Quan; Zhang, Yi; Du, Jie; Zhao, Meirong

2017-10-01

Synthetic pyrethroids (SPs) are one of the most widely used pesticides and frequently detected in the aquatic environment. Previous studies have shown that SPs posed high aquatic toxicity, but information on the developmental toxicity and endocrine disruption on zebrafish (Danio rerio) at environmentally relevant concentrations is limited. In this study, zebrafish embryos were employed to examine the adverse effects of λ-cyhalothrin (LCT), fenvalerate (FEN), and permethrin (PM) at 2.5, 10, 25, 125, 500 nM for 96 h. The results showed these 3 SPs caused dose-dependent mortality, malformation rate, and hatching rate. Thyroid hormone triiodothyronine (T 3 ) levels were significantly decreased after exposure to LCT and FEN. Quantitative real-time PCR analysis was then performed on a series of nuclear receptors (NRs) genes involved in the hypothalamic-pituitary-gonadal (HPG), hypothalamic-pituitary-thyroid (HPT), hypothalamic-pituitary-adrenocortical (HPA) axes, and oxidative-stress-related system. Our results showed that LCT, FEN, and PM downregulated AR expression while upregulated ER1 expression, and caused alteration to ER2a and ER2b expression. As for the expression of TRα and TRβ, they were both decreased following exposure to the 3 SPs. LCT and PM downregulated the MR expression and FEN induced MR expression. In addition, the expression of GR was increased after treating with LCT, while it was suppressed after exposure to FEN and PM. The 3 SPs also caused various alterations to the expression of genes including AhRs, PPARα, and PXR. These findings suggest that these 3 SPs may cause developmental toxicity to zebrafish larvae by disrupting endocrine signaling at environmentally relevant concentrations. Copyright © 2017. Published by Elsevier Ltd.

Final Report on ITER Task Agreement 81-10

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brad J. Merrill

An International Thermonuclear Experimental Reactor (ITER) Implementing Task Agreement (ITA) on Magnet Safety was established between the ITER International Organization (IO) and the Idaho National Laboratory (INL) Fusion Safety Program (FSP) during calendar year 2004. The objectives of this ITA were to add new capabilities to the MAGARC code and to use this updated version of MAGARC to analyze unmitigated superconductor quench events for both poloidal field (PF) and toroidal field (TF) coils of the ITER design. This report documents the completion of the work scope for this ITA. Based on the results obtained for this ITA, an unmitigated quenchmore » event in an ITER larger PF coil does not appear to be as severe an accident as in an ITER TF coil.« less

Intersystem Implications of the Developmental Origins of Health and Disease: Advancing Health Promotion in the 21st Century.

PubMed

Barnes, Michael D; Heaton, Thomas L; Goates, Michael C; Packer, Justin M

2016-07-15

The developmental origins of health and disease (DOHaD) theory and life course theory (LCT) are emerging fields of research that have significant implications for the public health and health promotion professions. Using a DOHaD/LCT perspective, social determinants of health (SDH) take on new critical meaning by which health promotion professionals can implement DOHaD/LCT guided interventions, including recommended policies. Through these interventions, public health could further address the sources of worldwide chronic disease epidemics and reduce such disease rates substantially if related policy, programs, and interdisciplinary and multi-sector collaboration are emphasized. Additional characteristics of the most effective interventions involve context-specific adaptation and societal structures that impact upstream, early life environments on a broad scale, influencing multiple locations and/or diseases.

Analysis of LCT-13910 genotypes and bone mineral density in ancient skeletal materials.

PubMed

Mnich, Barbara; Spinek, Anna Elżbieta; Chyleński, Maciej; Sommerfeld, Aleksandra; Dabert, Miroslawa; Juras, Anna; Szostek, Krzysztof

2018-01-01

The relation of LCT-13910 genotypes and bone mineral density (BMD) has been the subject of modern-day human population studies, giving inconsistent results. In the present study we analyze for the first time a relation of LCT-13910 genotypes and BMD in historical skeletal individuals. Ancient population might be a model for testing this association due to elimination of non-natural factors affecting bone density. Among 22 medieval individuals from Sanok churchyard (South-Eastern Poland; dated from XIV to XVII c. AD) we identified 4 individuals with osteoporosis (mean BMD = 0.468 g/cm2, SD = 0.090), 10 individuals with osteopenia (mean BMD = 0.531 g/cm2, SD = 0.066) and 8 individuals with normal BMD values (mean BMD = 0,642 g/cm2, SD = 0.060). Analyses of BMD and LCT-13910 genotypes revealed that mean BMD was the highest (0.583 g/cm2, SD = 0.065) in the individuals with lactose tolerance genotypes (TT and CT). We also found possible association of lower BMD at the radius and CC genotypes due to higher but not statistically significant frequency of osteoporosis in the lactose intolerant group (p = 0.60). Statistically significant correlation was found between BMD and females aged 20-35 years, with tendency to reduce BMD with age (p = 0.02).

Characterization of a 6×6-mm2 75-μm cell MPPC suitable for the Cherenkov Telescope Array project

NASA Astrophysics Data System (ADS)

Romeo, G.; Bonanno, G.; Garozzo, S.; Grillo, A.; Marano, D.; Munari, M.; Timpanaro, M. C.; Catalano, O.; Giarrusso, S.; Impiombato, D.; La Rosa, G.; Sottile, G.

2016-08-01

This paper presents the latest characterization results of a novel Low Cross-Talk (LCT) large-area (6×6-mm2) Multi-Pixel Photon Counter (MPPC) detector manufactured by Hamamatsu, belonging to the recent LCT5 family and achieving a fill-factor enhancement and cross-talk reduction. In addition, the newly adopted resin coating is demonstrated to yield improved photon detection capabilities in the 290-350 nm spectral range, making the new LCT MPPC particularly suitable for emerging applications like Cherenkov Telescopes. For a 3×3-mm2 version of the new MPPC under test, a comparative analysis of the large pixel pitch (75-μm) detector versus the smaller pixel pitch (50-μm) detector is also undertaken. Furthermore, measurements of the 6×6-mm2 MPPC response versus the angle of incidence are provided for the characterized device.

Security analysis of quadratic phase based cryptography

NASA Astrophysics Data System (ADS)

Muniraj, Inbarasan; Guo, Changliang; Malallah, Ra'ed; Healy, John J.; Sheridan, John T.

2016-09-01

The linear canonical transform (LCT) is essential in modeling a coherent light field propagation through first-order optical systems. Recently, a generic optical system, known as a Quadratic Phase Encoding System (QPES), for encrypting a two-dimensional (2D) image has been reported. It has been reported together with two phase keys the individual LCT parameters serve as keys of the cryptosystem. However, it is important that such the encryption systems also satisfies some dynamic security properties. Therefore, in this work, we examine some cryptographic evaluation methods, such as Avalanche Criterion and Bit Independence, which indicates the degree of security of the cryptographic algorithms on QPES. We compare our simulation results with the conventional Fourier and the Fresnel transform based DRPE systems. The results show that the LCT based DRPE has an excellent avalanche and bit independence characteristics than that of using the conventional Fourier and Fresnel based encryption systems.

Choice of optical system is critical for the security of double random phase encryption systems

NASA Astrophysics Data System (ADS)

Muniraj, Inbarasan; Guo, Changliang; Malallah, Ra'ed; Cassidy, Derek; Zhao, Liang; Ryle, James P.; Healy, John J.; Sheridan, John T.

2017-06-01

The linear canonical transform (LCT) is used in modeling a coherent light-field propagation through first-order optical systems. Recently, a generic optical system, known as the quadratic phase encoding system (QPES), for encrypting a two-dimensional image has been reported. In such systems, two random phase keys and the individual LCT parameters (α,β,γ) serve as secret keys of the cryptosystem. It is important that such encryption systems also satisfy some dynamic security properties. We, therefore, examine such systems using two cryptographic evaluation methods, the avalanche effect and bit independence criterion, which indicate the degree of security of the cryptographic algorithms using QPES. We compared our simulation results with the conventional Fourier and the Fresnel transform-based double random phase encryption (DRPE) systems. The results show that the LCT-based DRPE has an excellent avalanche and bit independence characteristics compared to the conventional Fourier and Fresnel-based encryption systems.

Meta-Analysis of Structured Triglyceride versus Physical Mixture Medium- and Long-Chain Triglycerides for PN in Liver Resection Patients.

PubMed

Zhao, Yajie; Wang, Chengfeng

2017-01-01

The use of total parenteral nutrition can affect liver function, causing a series of problems such as cholestasis. The aim of this meta-analysis was to compare structured triglyceride- (STG-) based lipid emulsions with physical medium-chain triglyceride (MCT)/long-chain triglyceride (LCT) mixtures in patients who had undergone liver surgery to identify any differences between these two types of parenteral nutrition. We searched the databases of PubMed, the Cochrane Library, Web of Science, EMBASE, and Chinese Biomedicine Database from January 2007 to March 2017 and included studies that compared STG-based lipid emulsions with physical MCT/LCT mixtures for surgical patients with liver disease. The STG was more beneficial than physical MCT/LCT on recovery of liver function and immune function. Therefore, STGs may represent a promising alternative to other types of lipid emulsions for hepatic surgery patients.

The natural history of Leydig cell testicular tumours: an analysis of the National Cancer Registry.

PubMed

Nason, G J; Redmond, E J; Considine, S W; Omer, S I; Power, D; Sweeney, P

2018-05-01

Leydig cell tumour (LCT) of the testis is a rare histological subtype of stromal tumours, accounting for 1 to 3% of testicular neoplasms. The natural history of LCT is poorly understood. The aim of this study was to assess the incidence and natural history of Leydig cell tumours (LCT) of the testes. A search of the National Cancer Registry of Ireland database was performed regarding Leydig cell testicular tumours. Recurrence free survival (RFS) and disease-specific survival (DSS) were analysed. Between 1994 and 2013, 2755 new cases of testicular cancer were diagnosed in Ireland. Of these, 22 (0.79%) were Leydig cell tumours. Nineteen were invasive (stage T1) and three were in situ (stage Tis). One patient developed a local recurrence following an organ preserving procedure and underwent a completion orchidectomy 107 days after initial diagnosis. No further treatment was required. There have been no disease-specific deaths. The 1-, 3- and 5-year overall survival (OS) rates were 95.5, 88.2 and 73.3%, respectively. The 5-year disease-specific survival (DSS) was 100% and the 5-year recurrence free survival (RFS) was 93.3%. From the National Cancer Registry, LCT has been shown to be a rare subtype of testicular tumour. Due to the relatively favourable natural history, it may be possible to tailor less aggressive surveillance regimens in these patients.

Lattice cluster theory for dense, thin polymer films.

PubMed

Freed, Karl F

2015-04-07

While the application of the lattice cluster theory (LCT) to study the miscibility of polymer blends has greatly expanded our understanding of the monomer scale molecular details influencing miscibility, the corresponding theory for inhomogeneous systems has not yet emerged because of considerable technical difficulties and much greater complexity. Here, we present a general formulation enabling the extension of the LCT to describe the thermodynamic properties of dense, thin polymer films using a high dimension, high temperature expansion. Whereas the leading order of the LCT for bulk polymer systems is essentially simple Flory-Huggins theory, the highly non-trivial leading order inhomogeneous LCT (ILCT) for a film with L layers already involves the numerical solution of 3(L - 1) coupled, highly nonlinear equations for the various density profiles in the film. The new theory incorporates the essential "transport" constraints of Helfand and focuses on the strict imposition of excluded volume constraints, appropriate to dense polymer systems, rather than the maintenance of chain connectivity as appropriate for lower densities and as implemented in self-consistent theories of polymer adsorption at interfaces. The ILCT is illustrated by presenting examples of the computed profiles of the density, the parallel and perpendicular bonds, and the chain ends for free standing and supported films as a function of average film density, chain length, temperature, interaction with support, and chain stiffness. The results generally agree with expected general trends.

Medium-chain versus long-chain triacylglycerol emulsion hydrolysis by lipoprotein lipase and hepatic lipase: Implications for the mechanisms of lipase action

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deckelbaum, R.J.; Hamilton, J.A.; Butbul, E.

1990-02-06

To explore how enzyme affinities and enzyme activities regulate hydrolysis of water-insoluble substrates, the authors compared hydrolysis of phospholipid-stabilized emulsions of medium-chain (MCT) versus long-chain triacylglycerols (LCT). Because substrate solubility at the emulsion surface might modulate rates of hydrolysis, the ability of egg yolk phosphatidylcholine to solubilize MCT was examined by NMR spectroscopy. Chemical shift measurements showed that 11 mol % of ({sup 13}C)carbonyl enriched trioctanoin was incorporated into phospholipid vesicles as a surface component. Line widths of trioctanoin surface peaks were half that of LCT, and relaxation times, T{sub 1}, were also shorter for trioctanoin, showing greater mobility formore » MCT in phospholipid. In assessing the effects of these differences in solubility on lipolysis, they found that both purified bovine milk lipoprotein lipase and human hepatic lipase hydrolyzed MCT at rates at least 2-fold higher than for LCT. Differences in affinity were also demonstrated in mixed incubations where increasing amounts of LCT emulsion resulted in decreased hydrolysis of MCT emulsions. These results suggest that despite lower enzyme affinity for MCT emulsions, shorter chain triacylglycerols are more readily hydrolyzed by lipoprotein and hepatic lipases than long-chain triacylglycerols because of greater MCT solubility and mobility at the emulsion-water interface.« less

Analysis of LCT-13910 genotypes and bone mineral density in ancient skeletal materials

PubMed Central

Mnich, Barbara; Spinek, Anna Elżbieta; Chyleński, Maciej; Sommerfeld, Aleksandra; Dabert, Miroslawa; Szostek, Krzysztof

2018-01-01

The relation of LCT-13910 genotypes and bone mineral density (BMD) has been the subject of modern-day human population studies, giving inconsistent results. In the present study we analyze for the first time a relation of LCT-13910 genotypes and BMD in historical skeletal individuals. Ancient population might be a model for testing this association due to elimination of non-natural factors affecting bone density. Among 22 medieval individuals from Sanok churchyard (South-Eastern Poland; dated from XIV to XVII c. AD) we identified 4 individuals with osteoporosis (mean BMD = 0.468 g/cm2, SD = 0.090), 10 individuals with osteopenia (mean BMD = 0.531 g/cm2, SD = 0.066) and 8 individuals with normal BMD values (mean BMD = 0,642 g/cm2, SD = 0.060). Analyses of BMD and LCT-13910 genotypes revealed that mean BMD was the highest (0.583 g/cm2, SD = 0.065) in the individuals with lactose tolerance genotypes (TT and CT). We also found possible association of lower BMD at the radius and CC genotypes due to higher but not statistically significant frequency of osteoporosis in the lactose intolerant group (p = 0.60). Statistically significant correlation was found between BMD and females aged 20–35 years, with tendency to reduce BMD with age (p = 0.02). PMID:29708972

The European lactase persistence genotype determines the lactase persistence state and correlates with gastrointestinal symptoms in the Hispanic and Amerindian Chilean population: a case–control and population-based study

PubMed Central

Morales, Eugenia; Azocar, Lorena; Maul, Ximena; Perez, Claudio; Chianale, José

2011-01-01

Background The lactase persistent (LP) or lactase non-persistent (LNP) state in European adults is genetically determined by a single nucleotide polymorphism (SNP) located 13.9 kb upstream of the lactase (LCT) gene, known as LCT C>T−13910 (rs4988235). The LNP condition leads to an inability to digest the milk sugar lactose leading to gastrointestinal symptoms and can affect nutrient and calcium intake in certain populations. Objectives The authors studied a group of 51 Chilean patients to assess whether this SNP influences the LP/LNP state in this population, and determined the prevalence of LCT C>T−13910 genotypes in a representative sample of 216 Hispanics and 43 Amerindians with correlation to digestive symptoms. Design Case–control study done in Chilean patients with clinical suspicion of LNP that were assessed using clinical survey, hydrogen breath test (HBT) and SNP genotyping. The population sample of Hispanics and Amerindians was assessed by clinical survey and SNP genotyping. Results Of the 51 patients with clinical suspicion of LNP, 29 were HBT-positive. The CC genotype (LNP) was present in 89.7% of the patients with positive HBT and in only 4.7% of those with negative HBT. The prevalence of the CC genotype was 56.9% in the Hispanic population and 88.3% in Amerindians, and was associated with a higher self-reported clinical intolerance to ingestion of dairy products. Conclusion The LP/LNP state is determined by the LCT C>T−13910 variant in Chileans. This variant predicts digestive symptoms associated with the ingestion of lactose and is a good tool for the diagnosis of primary adult hypolactasia. The LCT T−13910 allele is rare in the Amerindian population and is suggestive of European ancestry in this contemporary population. PMID:22021768

Self-assembly and glass-formation in a lattice model of telechelic polymer melts: Influence of stiffness of the sticky bonds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Wen-Sheng, E-mail: wsxu@uchicago.edu; Freed, Karl F., E-mail: freed@uchicago.edu; Department of Chemistry, The University of Chicago, Chicago, Illinois 60637

2016-06-07

Telechelic polymers are chain macromolecules that may self-assemble through the association of their two mono-functional end groups (called “stickers”). A deep understanding of the relation between microscopic molecular details and the macroscopic physical properties of telechelic polymers is important in guiding the rational design of telechelic polymer materials with desired properties. The lattice cluster theory (LCT) for strongly interacting, self-assembling telechelic polymers provides a theoretical tool that enables establishing the connections between important microscopic molecular details of self-assembling polymers and their bulk thermodynamics. The original LCT for self-assembly of telechelic polymers considers a model of fully flexible linear chains [J.more » Dudowicz and K. F. Freed, J. Chem. Phys. 136, 064902 (2012)], while our recent work introduces a significant improvement to the LCT by including a description of chain semiflexibility for the bonds within each individual telechelic chain [W.-S. Xu and K. F. Freed, J. Chem. Phys. 143, 024901 (2015)], but the physically associative (or called “sticky”) bonds between the ends of the telechelics are left as fully flexible. Motivated by the ubiquitous presence of steric constraints on the association of real telechelic polymers that impart an additional degree of bond stiffness (or rigidity), the present paper further extends the LCT to permit the sticky bonds to be semiflexible but to have a stiffness differing from that within each telechelic chain. An analytical expression for the Helmholtz free energy is provided for this model of linear telechelic polymer melts, and illustrative calculations demonstrate the significant influence of the stiffness of the sticky bonds on the self-assembly and thermodynamics of telechelic polymers. A brief discussion is also provided for the impact of self-assembly on glass-formation by combining the LCT description for this extended model of telechelic polymers with the Adam-Gibbs relation between the structural relaxation time and the configurational entropy.« less

Effects of parenteral structured lipid emulsion on modulating the inflammatory response in rats undergoing a total gastrectomy.

PubMed

Lin, Ming-Tsan; Yeh, Sung-Ling; Tsou, Shung-Sheng; Wang, Ming-Yang; Chen, Wei-Jao

2009-01-01

Structured lipid emulsion improves the nitrogen balance and is rapidly cleared from the blood of moderately catabolic patients. However, the effects of structured lipids on inflammatory reactions during major surgery are not clear. This study investigated the effect of a parenteral structured triacylglycerol emulsion on leukocyte adhesion molecule expression and inflammatory mediator production in rats undergoing a total gastrectomy. Normal rats with internal jugular catheters were assigned to three experimental groups and received total parenteral nutrition. At the same time, a total gastrectomy was performed on the experimental groups. The total parenteral nutrition solutions were isonitrogenous and identical in nutrient compositions except for differences in the composition of the fat emulsion. Group 1 received a conventional fat emulsion with long-chain triacylglycerols (LCTs), group 2 received a physical mixture of medium-chain triacylglycerols (MCTs) and LCTs (MCT/LCT), and group 3 received structured lipids composed of MCTs and LCTs (STG). Half of the rats in each respective group were sacrificed 1 d and the other half 3 d after surgery to examine the analytical parameters. Plasma cholesterol and free fatty acid levels in the STG group were lower than those in the other groups after surgery. The STG group had lower leukocyte CD11a/CD18 expressions than the MCT/LCT group 3 d after surgery, and CD11b/CD18 expressions in the STG group were lower than those in the LCT group on postoperative days. The STG group had higher monocyte chemotactic protein-1 and macrophage inflammatory protein-2 levels in peritoneal lavage fluid than did the other two groups. These results suggest that, compared with the LCT and MCT/LCT groups, rats administered STG had lower plasma lipid concentrations and leukocyte integrin expressions. In addition, STG administration may cause increased recruiting of neutrophils and monocytes at the site of injury and enhance antipathogenicity in rats undergoing a total gastrectomy.

A comparison of long-chain triglycerides and medium-chain triglycerides on weight loss and tumour size in a cachexia model.

PubMed Central

Tisdale, M. J.; Brennan, R. A.

1988-01-01

A comparison has been made between the ability of long-chain triglycerides (LCT) and medium-chain triglycerides (MCT) to prevent weight loss induced by the cachexia-inducing colon adenocarcinoma (MAC16) and to reduce tumour size. There was no difference in calorie consumption or nitrogen intake between the various groups. When compared with a normal control high carbohydrate, low fat diet, animals fed MCT showed a reduced weight loss and a marked reduction in tumour size. In contrast neither weight loss nor tumour size differed significantly from the controls in animals fed the LCT diet. An elevated plasma level of 3-hydroxybuturate was found only in the animals fed the MCT diets. Administration of LCT caused an increase in the plasma level of FFA, which was not observed in the MCT group. These results suggest that diets containing MCT would provide the best ketogenic regime to reverse the weight loss in cancer cachexia with a concomitant reduction in tumour size. PMID:3219268

A comparison of medium-chain and long-chain triglycerides in surgical patients.

PubMed Central

Jiang, Z M; Zhang, S Y; Wang, X R; Yang, N F; Zhu, Y; Wilmore, D

1993-01-01

Available lipid emulsions made from soybean or safflower oil are classified as long-chain triglycerides (LCT). In contrast, medium-chain triglyceride (MCT) emulsions have different physical properties and are metabolized by other biochemical pathways. To compare the differences between these two fat emulsions, the authors studied 12 surgical patients and 6 volunteers. These subjects were randomly assigned to receive parenteral nutrition with MCT or LCT emulsion. Measurement of arterial and venous concentration differences across the forearm demonstrated that muscle utilization was significantly improved with MCT administration. There was also a trend toward improved nitrogen balance in the MCT group, and less weight loss in the postoperative period also was observed in this group. During the fat clearance test, the serum ketone concentrations were significantly higher in the MCT than the LCT group. The improvement in nitrogen retention may be associated with increasing ketone and insulin levels. Fat emulsions containing 50% MCT are safe for use in parenteral nutrition and may provide an alternate fuel that improves protein metabolism. PMID:8439215

Optical colour image watermarking based on phase-truncated linear canonical transform and image decomposition

NASA Astrophysics Data System (ADS)

Su, Yonggang; Tang, Chen; Li, Biyuan; Lei, Zhenkun

2018-05-01

This paper presents a novel optical colour image watermarking scheme based on phase-truncated linear canonical transform (PT-LCT) and image decomposition (ID). In this proposed scheme, a PT-LCT-based asymmetric cryptography is designed to encode the colour watermark into a noise-like pattern, and an ID-based multilevel embedding method is constructed to embed the encoded colour watermark into a colour host image. The PT-LCT-based asymmetric cryptography, which can be optically implemented by double random phase encoding with a quadratic phase system, can provide a higher security to resist various common cryptographic attacks. And the ID-based multilevel embedding method, which can be digitally implemented by a computer, can make the information of the colour watermark disperse better in the colour host image. The proposed colour image watermarking scheme possesses high security and can achieve a higher robustness while preserving the watermark’s invisibility. The good performance of the proposed scheme has been demonstrated by extensive experiments and comparison with other relevant schemes.

Applying graph theory to protein structures: an atlas of coiled coils.

PubMed

Heal, Jack W; Bartlett, Gail J; Wood, Christopher W; Thomson, Andrew R; Woolfson, Derek N

2018-05-02

To understand protein structure, folding and function fully and to design proteins de novo reliably, we must learn from natural protein structures that have been characterised experimentally. The number of protein structures available is large and growing exponentially, which makes this task challenging. Indeed, computational resources are becoming increasingly important for classifying and analysing this resource. Here, we use tools from graph theory to define an atlas classification scheme for automatically categorising certain protein substructures. Focusing on the α-helical coiled coils, which are ubiquitous protein-structure and protein-protein interaction motifs, we present a suite of computational resources designed for analysing these assemblies. iSOCKET enables interactive analysis of side-chain packing within proteins to identify coiled coils automatically and with considerable user control. Applying a graph theory-based atlas classification scheme to structures identified by iSOCKET gives the Atlas of Coiled Coils, a fully automated, updated overview of extant coiled coils. The utility of this approach is illustrated with the first formal classification of an emerging subclass of coiled coils called α-helical barrels. Furthermore, in the Atlas, the known coiled-coil universe is presented alongside a partial enumeration of the 'dark matter' of coiled-coil structures; i.e., those coiled-coil architectures that are theoretically possible but have not been observed to date, and thus present defined targets for protein design. iSOCKET is available as part of the open-source GitHub repository associated with this work (https://github.com/woolfson-group/isocket). This repository also contains all the data generated when classifying the protein graphs. The Atlas of Coiled Coils is available at: http://coiledcoils.chm.bris.ac.uk/atlas/app.

Combining LCT tools for the optimization of an industrial process: material and energy flow analysis and best available techniques.

PubMed

Rodríguez, M T Torres; Andrade, L Cristóbal; Bugallo, P M Bello; Long, J J Casares

2011-09-15

Life cycle thinking (LCT) is one of the philosophies that has recently appeared in the context of the sustainable development. Some of the already existing tools and methods, as well as some of the recently emerged ones, which seek to understand, interpret and design the life of a product, can be included into the scope of the LCT philosophy. That is the case of the material and energy flow analysis (MEFA), a tool derived from the industrial metabolism definition. This paper proposes a methodology combining MEFA with another technique derived from sustainable development which also fits the LCT philosophy, the BAT (best available techniques) analysis. This methodology, applied to an industrial process, seeks to identify the so-called improvable flows by MEFA, so that the appropriate candidate BAT can be selected by BAT analysis. Material and energy inputs, outputs and internal flows are quantified, and sustainable solutions are provided on the basis of industrial metabolism. The methodology has been applied to an exemplary roof tile manufacture plant for validation. 14 Improvable flows have been identified and 7 candidate BAT have been proposed aiming to reduce these flows. The proposed methodology provides a way to detect improvable material or energy flows in a process and selects the most sustainable options to enhance them. Solutions are proposed for the detected improvable flows, taking into account their effectiveness on improving such flows. Copyright © 2011 Elsevier B.V. All rights reserved.

Impact of higher order diagrams on phase equilibrium calculations for small molecules using lattice cluster theory

NASA Astrophysics Data System (ADS)

Zimmermann, Patrick; Walowski, Christoph; Enders, Sabine

2018-03-01

The Lattice Cluster Theory (LCT) provides a powerful tool to predict thermodynamic properties of large molecules (e.g., polymers) of different molecular architectures. When the pure-component parameters of a certain compound have been derived by adjustment to experimental data and the number of atoms is held constant within the molecule so that only the architecture is changed, the LCT is capable of predicting the properties of isomers without further parameter adjustment just based on the incorporation of molecular architecture. Trying to predict the thermodynamic properties of smaller molecules, one might face some challenges, which are addressed in this contribution. After factoring out the mean field term of the partition function, the LCT poses an expression that involves corrections to the mean field depending on molecular architecture, resulting in the free energy formally being expressed as a double series expansion in lattice coordination number z and interaction energy ɛ ˜ . In the process of deriving all contributing sub-structures within a molecule, some parts have been neglected to this point due to the double series expansion being truncated after the order ɛ˜ 2z-2. We consider the neglected parts that are of the order z-3 and reformulate the expression for the free energy within the LCT to achieve a higher predictive capability of the theory when it comes to small isomers and compressible systems. The modified version was successfully applied for phase equilibrium calculations of binary mixtures composed of linear and branched alkanes.

Age and Date for Early Arrival of the Acheulian in Europe (Barranc de la Boella, la Canonja, Spain)

PubMed Central

Vallverdú, Josep; Saladié, Palmira; Rosas, Antonio; Huguet, Rosa; Cáceres, Isabel; Mosquera, Marina; Garcia-Tabernero, Antonio; Estalrrich, Almudena; Lozano-Fernández, Iván; Pineda-Alcalá, Antonio; Carrancho, Ángel; Villalaín, Juan José; Bourlès, Didier; Braucher, Régis; Lebatard, Anne; Vilalta, Jaume; Esteban-Nadal, Montserrat; Bennàsar, Maria Lluc; Bastir, Marcus; López-Polín, Lucía; Ollé, Andreu; Vergés, Josep Maria; Ros-Montoya, Sergio; Martínez-Navarro, Bienvenido; García, Ana; Martinell, Jordi; Expósito, Isabel; Burjachs, Francesc; Agustí, Jordi; Carbonell, Eudald

2014-01-01

The first arrivals of hominin populations into Eurasia during the Early Pleistocene are currently considered to have occurred as short and poorly dated biological dispersions. Questions as to the tempo and mode of these early prehistoric settlements have given rise to debates concerning the taxonomic significance of the lithic assemblages, as trace fossils, and the geographical distribution of the technological traditions found in the Lower Palaeolithic record. Here, we report on the Barranc de la Boella site which has yielded a lithic assemblage dating to ∼1 million years ago that includes large cutting tools (LCT). We argue that distinct technological traditions coexisted in the Iberian archaeological repertoires of the late Early Pleistocene age in a similar way to the earliest sub-Saharan African artefact assemblages. These differences between stone tool assemblages may be attributed to the different chronologies of hominin dispersal events. The archaeological record of Barranc de la Boella completes the geographical distribution of LCT assemblages across southern Eurasia during the EMPT (Early-Middle Pleistocene Transition, circa 942 to 641 kyr). Up to now, chronology of the earliest European LCT assemblages is based on the abundant Palaeolithic record found in terrace river sequences which have been dated to the end of the EMPT and later. However, the findings at Barranc de la Boella suggest that early LCT lithic assemblages appeared in the SW of Europe during earlier hominin dispersal episodes before the definitive colonization of temperate Eurasia took place. PMID:25076416

Nonshivering thermogenesis and adaptation to fasting in king penguin chicks.

PubMed

Duchamp, C; Barre, H; Delage, D; Rouanet, J L; Cohen-Adad, F; Minaire, Y

1989-10-01

The ability to develop nonshivering thermogenesis (NST) and the effect of fasting on thermogenic response to cold were studied in winter-acclimatized king penguin chicks. Metabolic rate (MR) and integrated electrical muscle activity were measured at different ambient temperatures. In cold-acclimatized (5 degrees C) fed chicks, shivering threshold temperature (STT) was 9.4 degrees C lower than lower critical temperature (LCT), indicating that NST (0.7 W/kg) occurs at moderate cold, whereas in control chicks fed and reared at 25 degrees C for 3 wk, LCT and STT were similar. Chicks reared in the cold and fasting for 3 wk or 4-5 mo (natural winter fast) developed an NST of 0.8 and 2.4 W/kg, respectively, despite the fast. In fasting chicks, the intercept of the metabolic curve with the abscissa at zero MR was far below body temperature, contrasting with the classic model for heat loss. Their low LCT indicates the capacity of a large reduction in convective conductance characteristic of diving animals and allows energy sparing in moderate cold. Below LCT, conductance reincreases progressively, leading to a steeper than expected slope of the metabolic curve and allowing preservation of a threshold temperature in the shell. These results show for the first time in a wild young bird the development of NST after cold acclimatization. Further, at the temperature of cold acclimatization, an energy-sparing mechanism is shown in response to long-term fast adaptation.

Age and date for early arrival of the Acheulian in Europe (Barranc de la Boella, la Canonja, Spain).

PubMed

Vallverdú, Josep; Saladié, Palmira; Rosas, Antonio; Huguet, Rosa; Cáceres, Isabel; Mosquera, Marina; Garcia-Tabernero, Antonio; Estalrrich, Almudena; Lozano-Fernández, Iván; Pineda-Alcalá, Antonio; Carrancho, Ángel; Villalaín, Juan José; Bourlès, Didier; Braucher, Régis; Lebatard, Anne; Vilalta, Jaume; Esteban-Nadal, Montserrat; Bennàsar, Maria Lluc; Bastir, Marcus; López-Polín, Lucía; Ollé, Andreu; Vergés, Josep Maria; Ros-Montoya, Sergio; Martínez-Navarro, Bienvenido; García, Ana; Martinell, Jordi; Expósito, Isabel; Burjachs, Francesc; Agustí, Jordi; Carbonell, Eudald

2014-01-01

The first arrivals of hominin populations into Eurasia during the Early Pleistocene are currently considered to have occurred as short and poorly dated biological dispersions. Questions as to the tempo and mode of these early prehistoric settlements have given rise to debates concerning the taxonomic significance of the lithic assemblages, as trace fossils, and the geographical distribution of the technological traditions found in the Lower Palaeolithic record. Here, we report on the Barranc de la Boella site which has yielded a lithic assemblage dating to ∼1 million years ago that includes large cutting tools (LCT). We argue that distinct technological traditions coexisted in the Iberian archaeological repertoires of the late Early Pleistocene age in a similar way to the earliest sub-Saharan African artefact assemblages. These differences between stone tool assemblages may be attributed to the different chronologies of hominin dispersal events. The archaeological record of Barranc de la Boella completes the geographical distribution of LCT assemblages across southern Eurasia during the EMPT (Early-Middle Pleistocene Transition, circa 942 to 641 kyr). Up to now, chronology of the earliest European LCT assemblages is based on the abundant Palaeolithic record found in terrace river sequences which have been dated to the end of the EMPT and later. However, the findings at Barranc de la Boella suggest that early LCT lithic assemblages appeared in the SW of Europe during earlier hominin dispersal episodes before the definitive colonization of temperate Eurasia took place.

Hypolactasia is associated with insulin resistance in nonalcoholic steatohepatitis

PubMed Central

de Campos Mazo, Daniel Ferraz; Mattar, Rejane; Stefano, José Tadeu; da Silva-Etto, Joyce Matie Kinoshita; Diniz, Márcio Augusto; Duarte, Sebastião Mauro Bezerra; Rabelo, Fabíola; Lima, Rodrigo Vieira Costa; de Campos, Priscila Brizolla; Carrilho, Flair José; Oliveira, Claudia P

2016-01-01

AIM To assess lactase gene (LCT)-13910C>T polymorphisms in Brazilian non-alcoholic fatty liver disease (NAFLD) and nonalcoholic steatohepatitis (NASH) patients in comparison with healthy controls. METHODS This was a transverse observational clinical study with NAFLD patients who were followed at the Hepatology Outpatient Unit of the Hospital das Clínicas, São Paulo, Brazil. The polymorphism of lactase non-persistence/lactase persistence (LCT-13910C>T) was examined by PCR-restriction fragment length polymorphism technique in 102 liver biopsy-proven NAFLD patients (steatosis in 9 and NASH in 93) and compared to those of 501 unrelated healthy volunteers. Anthropometric, clinical, biochemical and liver histology data were analyzed. Continuous variables were compared using the t or Mann-Whitney tests, and categorical data were compared with the Fisher’s exact test. Univariate logistic regression and multivariate logistic regression adjusted for gender and age were performed. RESULTS No differences in the LCT-13910 genotype frequencies were noted between the NAFLD patients (66.67% of the patients with steatosis were CC, 33.33% were CT, and none were TT; 55.91% of the patients with NASH were CC, 39.78% were CT, and 4.3% were TT; P = 0.941) and the healthy controls (59.12% were CC, 35.67% were CT, and 5.21% were TT) or between the steatosis and NASH patients. That is, the distribution of the lactase non-persistence/lactase persistence polymorphism (LCT-13910C>T) in the patients with NAFLD was equal to that in the general population. In the NASH patients, the univariate analysis revealed that the lactase non-persistence (low lactase activity or hypolactasia) phenotype was associated with higher insulin levels (23.47 ± 15.94 μU/mL vs 15.8 ± 8.33 μU/mL, P = 0.027) and a higher frequency of insulin resistance (91.84% vs 72.22%, P = 0.02) compared with the lactase persistence phenotype. There were no associations between the LCT genotypes and diabetes (P = 0.651), dyslipidaemia (P = 0.328), hypertension (P = 0.507) or liver histology in these patients. Moreover, in the NASH patients, hypolactasia was an independent risk factor for insulin resistance even after adjusting for gender and age [OR = 5.0 (95%CI: 1.35-20; P = 0.017)]. CONCLUSION The LCT-13910 genotype distribution in Brazilian NAFLD patients was the same as that of the general population, but hypolactasia increased the risk of insulin resistance in the NASH patients. PMID:27648154

The punctal apposition syndrome: a new surgical approach.

PubMed

Francis, I C; Wan, M K

2002-11-01

To assess the punctal apposition syndrome (PAS) and its response to lateral canthal tendon (LCT) repair. In this retrospective, interventional case series, five patients (seven symptomatic eyes) with PAS were managed. Lateral canthal tendon repair was performed in all seven eyes. The main outcome measure was correction of watery eye symptomatology. All five patients achieved symptomatic resolution. Conjunctivochalasis and functional nasolacrimal duct obstruction were associated with the PAS. This new surgical approach to the PAS, using a LCT repair, was successful in all patients. Two patients (three eyes) required conjunctivochalasis excision.

A preliminary deposit model for lithium-cesium-tantalum (LCT) pegmatites

USGS Publications Warehouse

Bradley, Dwight; McCauley, Andrew

2013-01-01

This report is part of an effort by the U.S. Geological Survey to update existing mineral deposit models and to develop new ones. We emphasize practical aspects of pegmatite geology that might directly or indirectly help in exploration for lithium-cesium-tantalum (LCT) pegmatites, or for assessing regions for pegmatite-related mineral resource potential. These deposits are an important link in the world’s supply chain of rare and strategic elements, accounting for about one-third of world lithium production, most of the tantalum, and all of the cesium.

Association Between Polymorphisms of VDR, COL1A1, and LCT genes and bone mineral density in Belarusian women with severe postmenopausal osteoporosis.

PubMed

Marozik, Pavel; Mosse, Irma; Alekna, Vidmantas; Rudenko, Ema; Tamulaitienė, Marija; Ramanau, Heorhi; Strazdienė, Vaidilė; Samokhovec, Volha; Ameliyanovich, Maxim; Byshnev, Nikita; Gonchar, Alexander; Kundas, Liubov; Zhur, Krystsina

2013-01-01

BACKGROUND AND OBJECTIVE. Variation of osteoporosis in the population is the result of an interaction between the genotype and the environment, and the genetic causes of osteoporosis are being widely investigated. The aim of this study was to analyze the association between the polymorphisms of the vitamin D receptor (VDR), type I collagen (COL1A1), and lactase (LCT) genes and severe postmenopausal osteoporosis as well as bone mineral density (BMD). MATERIAL AND METHODS. A total of 54 women with severe postmenopausal osteoporosis and 77 controls (mean age, 58.3 years [SD, 6.2] and 56.7 years [SD, 7.42], respectively) were included into the study. The subjects were recruited at the City Center for Osteoporosis Prevention (Minsk, Belarus). Dual-energy x-ray absorptiometry was used to measure bone mineral density at the lumbar spine and the femoral neck. Severe osteoporosis was diagnosed in the women with the clinical diagnosis of postmenopausal osteoporosis and at least 1 fragility fracture. The control group included women without osteoporosis. Polymorphic sites in osteoporosis predisposition genes (ApaI, BsmI, TaqI, and Cdx2 of the VDR gene, G2046T of the COL1A1 gene, and T-13910C of the LCT gene) were determined using the polymerase chain reaction on the deoxyribonucleic acid isolated from dried bloodspots. RESULTS. The data showed that the ApaI and BsmI polymorphisms of the VDR gene and T- 13910C of the LCT gene were associated with severe postmenopausal osteoporosis in the analyzed Belarusian women (P<0.01). A statistically significant positive correlation between the VDR risk genotypes ApaI and TaqI and bone mineral density was found (P<0.05). CONCLUSIONS. The findings of this study suggest that at least the ApaI and BsmI polymorphisms of the VDR gene and T-13910C of the LCT gene are associated with the risk of postmenopausal osteoporosis in our sample of the Belarusian women.

Sensations induced by medium and long chain triglycerides: role of gastric tone and hormones

PubMed Central

Barbera, R; Peracchi, M; Brighenti, F; Cesana, B; Bianchi, P; Basilisco, G

2000-01-01

BACKGROUND—The relative roles of gastric relaxation and the neuroendocrine signals released by the small intestine in the perception of nutrient induced sensations are controversial. The different effects of long chain (LCT) and medium chain (MCT) triglyceride ingestion on perception, gastric relaxation, and hormonal release may help to elucidate the mechanisms underlying nutrient induced sensations.
AIMS—To compare the effects of intraduodenal LCT and MCT infusions on perception, gastric tone, and plasma gut hormone levels in healthy subjects.
SUBJECTS—Nine fasting healthy volunteers.
METHODS—The subjects received duodenal infusions of saline followed by LCTs and MCTs in a randomised order on two different days. The sensations were rated on a visual analogue scale. Gastric tone was measured using a barostat, and plasma gut hormone levels by radioimmunoassay.
RESULTS—LCT infusion increased satiation scores, reduced gastric tone, and increased the levels of plasma cholecystokinin, gastric inhibitory polypeptide, neurotensin, and pancreatic polypeptide. MCT infusion reduced gastric tone but did not significantly affect perception or plasma gut hormone levels. LCTs produced greater gastric relaxation than MCTs.
CONCLUSIONS—The satiation induced by intraduodenal LCT infusion seems to involve changes in gastric tone and plasma gut hormone levels. The gastric relaxation induced by MCT infusion, together with the absence of any significant change in satiation scores and plasma hormone levels, suggests that, at least up to a certain level, gastric relaxation is not sufficient to induce satiation and that nutrient induced gastric relaxation may occur through cholecystokinin independent mechanisms.


Keywords: gastric tone; triglyceride; hormones; satiation; cholecystokinin; nutrients PMID:10601051

The global age distribution of granitic pegmatites

USGS Publications Warehouse

McCauley, Andrew; Bradley, Dwight C.

2014-01-01

An updated global compilation of 377 new and previously published ages indicates that granitic pegmatites range in age from Mesoarchean to Neogene and have a semi-periodic age distribution. Undivided granitic pegmatites show twelve age maxima: 2913, 2687, 2501, 1853, 1379, 1174, 988, 525, 483, 391, 319, and 72 Ma. These peaks correspond broadly with various proxy records of supercontinent assembly, including the age distributions of granites, detrital zircon grains, and passive margins. Lithium-cesium-tantalum (LCT) pegmatites have a similar age distribution to the undivided granitic pegmatites, with maxima at 2638, 1800, 962, 529, 485, 371, 309, and 274 Ma. Lithium and Ta resources in LCT pegmatites are concentrated in the Archean and Phanerozoic. While there are some Li resources from the Proterozoic, the dominantly bimodal distribution of resources is particularly evident for Ta. This distribution is similar to that of orogenic gold deposits, and has been interpreted to reflect the preservation potential of the orogenic belts where these deposits are formed. Niobium-yttrium-fluorine (NYF) pegmatites show similar age distributions to LCT pegmatites, but with a strong maximum at ca. 1000 Ma.

Equivalence of linear canonical transform domains to fractional Fourier domains and the bicanonical width product: a generalization of the space-bandwidth product.

PubMed

Oktem, Figen S; Ozaktas, Haldun M

2010-08-01

Linear canonical transforms (LCTs) form a three-parameter family of integral transforms with wide application in optics. We show that LCT domains correspond to scaled fractional Fourier domains and thus to scaled oblique axes in the space-frequency plane. This allows LCT domains to be labeled and ordered by the corresponding fractional order parameter and provides insight into the evolution of light through an optical system modeled by LCTs. If a set of signals is highly confined to finite intervals in two arbitrary LCT domains, the space-frequency (phase space) support is a parallelogram. The number of degrees of freedom of this set of signals is given by the area of this parallelogram, which is equal to the bicanonical width product but usually smaller than the conventional space-bandwidth product. The bicanonical width product, which is a generalization of the space-bandwidth product, can provide a tighter measure of the actual number of degrees of freedom, and allows us to represent and process signals with fewer samples.

Functional Laterality of Task-Evoked Activation in Sensorimotor Cortex of Preterm Infants: An Optimized 3 T fMRI Study Employing a Customized Neonatal Head Coil.

PubMed

Scheef, Lukas; Nordmeyer-Massner, Jurek A; Smith-Collins, Adam Pr; Müller, Nicole; Stegmann-Woessner, Gaby; Jankowski, Jacob; Gieseke, Jürgen; Born, Mark; Seitz, Hermann; Bartmann, Peter; Schild, Hans H; Pruessmann, Klaas P; Heep, Axel; Boecker, Henning

2017-01-01

Functional magnetic resonance imaging (fMRI) in neonates has been introduced as a non-invasive method for studying sensorimotor processing in the developing brain. However, previous neonatal studies have delivered conflicting results regarding localization, lateralization, and directionality of blood oxygenation level dependent (BOLD) responses in sensorimotor cortex (SMC). Amongst the confounding factors in interpreting neonatal fMRI studies include the use of standard adult MR-coils providing insufficient signal to noise, and liberal statistical thresholds, compromising clinical interpretation at the single subject level. Here, we employed a custom-designed neonatal MR-coil adapted and optimized to the head size of a newborn in order to improve robustness, reliability and validity of neonatal sensorimotor fMRI. Thirteen preterm infants with a median gestational age of 26 weeks were scanned at term-corrected age using a prototype 8-channel neonatal head coil at 3T (Achieva, Philips, Best, NL). Sensorimotor stimulation was elicited by passive extension/flexion of the elbow at 1 Hz in a block design. Analysis of temporal signal to noise ratio (tSNR) was performed on the whole brain and the SMC, and was compared to data acquired with an 'adult' 8 channel head coil published previously. Task-evoked activation was determined by single-subject SPM8 analyses, thresholded at p < 0.05, whole-brain FWE-corrected. Using a custom-designed neonatal MR-coil, we found significant positive BOLD responses in contralateral SMC after unilateral passive sensorimotor stimulation in all neonates (analyses restricted to artifact-free data sets = 8/13). Improved imaging characteristics of the neonatal MR-coil were evidenced by additional phantom and in vivo tSNR measurements: phantom studies revealed a 240% global increase in tSNR; in vivo studies revealed a 73% global and a 55% local (SMC) increase in tSNR, as compared to the 'adult' MR-coil. Our findings strengthen the importance of using optimized coil settings for neonatal fMRI, yielding robust and reproducible SMC activation at the single subject level. We conclude that functional lateralization of SMC activation, as found in children and adults, is already present in the newborn period.

Dietary medium-chain triglycerides promote oral allergic sensitization and orally induced anaphylaxis to peanut protein in mice.

PubMed

Li, Jianing; Wang, Yu; Tang, Lihua; de Villiers, Willem J S; Cohen, Donald; Woodward, Jerold; Finkelman, Fred D; Eckhardt, Erik R M

2013-02-01

The prevalence of peanut allergies is increasing. Peanuts and many other allergen sources contain significant amounts of triglycerides, which affect absorption of antigens but have unknown effects on sensitization and anaphylaxis. We recently reported that dietary medium-chain triglycerides (MCTs), which bypass mesenteric lymph and directly enter portal blood, reduce intestinal antigen absorption into blood compared with long-chain triglycerides (LCTs), which stimulate mesenteric lymph flow and are absorbed in chylomicrons through mesenteric lymph. We sought to test how dietary MCTs affect food allergy. C3H/HeJ mice were fed peanut butter protein in MCT, LCT (peanut oil), or LCT plus an inhibitor of chylomicron formation (Pluronic L81). Peanut-specific antibodies in plasma, responses of the mice to antigen challenges, and intestinal epithelial cytokine expression were subsequently measured. MCT suppressed antigen absorption into blood but stimulated absorption into Peyer patches. A single gavage of peanut protein with MCT, as well as prolonged feeding in MCT-based diets, caused spontaneous allergic sensitization. MCT-sensitized mice experienced IgG-dependent anaphylaxis on systemic challenge and IgE-dependent anaphylaxis on oral challenge. MCT feeding stimulated jejunal-epithelial thymic stromal lymphopoietin, Il25, and Il33 expression compared with that seen after LCT feeding and promoted T(H)2 cytokine responses in splenocytes. Moreover, oral challenges of sensitized mice with antigen in MCT significantly aggravated anaphylaxis compared with challenges with the LCT. Importantly, the effects of MCTs could be mimicked by adding Pluronic L81 to LCTs, and in vitro assays indicated that chylomicrons prevent basophil activation. Dietary MCTs promote allergic sensitization and anaphylaxis by affecting antigen absorption and availability and by stimulating T(H)2 responses. Copyright © 2012 American Academy of Allergy, Asthma & Immunology. Published by Mosby, Inc. All rights reserved.

Effects of short-term and long-term treatment with medium- and long-chain triglycerides ketogenic diet on cortical spreading depression in young rats.

PubMed

de Almeida Rabello Oliveira, Marcela; da Rocha Ataíde, Terezinha; de Oliveira, Suzana Lima; de Melo Lucena, Ana Luíza; de Lira, Carla Emmanuela Pereira Rodrigues; Soares, Anderson Acioli; de Almeida, Clarissa Beatriz Santos; Ximenes-da-Silva, Adriana

2008-03-21

The ketogenic diet (KD) is a high fat and low carbohydrate and protein diet. It is used in the clinical treatment of epilepsy, in order to decrease cerebral excitability. KD is usually composed by long-chain triglycerides (LCT) while medium-chain triglycerides (MCT) diet is beginning to be used in some clinical treatment of disorders of pyruvate carboxylase enzyme and long-chain fatty acid oxidation. Our study aimed to analyze the effects of medium- and long-chain KD on cerebral electrical activity, analyzing the propagation of the phenomenon of cortical spreading depression (CSD). Three groups of weaned rats (21 days old) received, for 7 weeks, either a control (AIN-93G diet), or a MCT-KD (rich in triheptanoin oil), or a LCT-KD (rich in soybean oil). They were compared to another three groups (21 days old) receiving the same diets for just 10 days. CSD propagation was evaluated just after ending the dietary treatments. Results showed that short-term KD treatment resulted in a significant reduction of the CSD velocity of propagation (control group: 4.02+/-1.04mm/min; MCT-KD: 0.81+/-1.46mm/min and LCT-KD: 2.26+/-0.41mm/min) compared to the control group. However, long-term treatment with both KDs had no effect on the CSD velocity (control group: 3.10+/-0.41mm/min, MCT-KD: 2.91+/-1.62mm/min, LCT-KD: 3.02+/-2.26mm/min) suggesting that both short-term KDs have a positive effect in decreasing brain cerebral excitability in young animals. These data show for the first time that triheptanoin has an effect on central nervous system.

Pharmacokinetics and pharmacodynamics of a new reformulated microemulsion and the long-chain triglyceride emulsion of propofol in beagle dogs

PubMed Central

Lee, S-H; Ghim, J-L; Song, M-H; Choi, H-G; Choi, B-M; Lee, H-M; Lee, E-K; Roh, Y-J; Noh, G-J

2009-01-01

Background and purpose: Microemulsion propofol was developed to eliminate lipid solvent-related adverse events of long-chain triglyceride emulsion (LCT) propofol. We compared dose proportionality, pharmacokinetic and pharmacodynamic characteristics of both formulations. Experimental approach: The study was a randomized, two-period and crossover design with 7-day wash-out period. Microemulsion and LCT propofol were administered by zero-order infusion (0.75, 1.00 and 1.25 mg·kg−1·min−1) for 20 min in 30 beagle dogs (male/female = 5/5 for each rate). Arterial samples were collected at preset intervals. The electroencephalographic approximate entropy (ApEn) was used as a measure of propofol effect. Dose proportionality, pharmacokinetic and pharmacodynamic bioequivalence were evaluated by non-compartmental analyses. Population analysis was performed using nonlinear mixed effects modelling. Key results: Both formulations showed dose proportionality at the applied dose range. The ratios of geometric means of AUClast and AUCinf between both formulations were acceptable for bioequivalence, whereas that of Cmax was not. The pharmacodynamic bioequivalence was indicated by the arithmetic means of AAC (areas above the ApEn time curves) and E0 (baseline ApEn)–Emax (maximally decreased ApEn) between both formulations. The pharmacokinetics of both formulations were best described by three compartment models. Body weight was a significant covariate for V1 of both formulations and sex for k21 of microemulsion propofol. The blood-brain equilibration rate constants (ke0, min−1) were 0.476 and 0.696 for microemulsion and LCT propofol respectively. Conclusions and implications: Microemulsion propofol was pharmacodynamically bioequivalent to LCT propofol although pharmacokinetic bioequivalence was incomplete, and demonstrated linear pharmacokinetics at the applied dose ranges. PMID:19925493

Potentials of RF/FSO Communication in UAS Operations

NASA Astrophysics Data System (ADS)

Griethe, Wolfgang; Heine, Frank

2013-08-01

Free Space Optical Communications (FSOC) has gained particular attention during the past few years and is progressing continuously. With the successful in-orbit verification of a Laser Communication Terminal (LCT), the coherent homodyne BPSK scheme advanced to a standard for Free-Space Optical Communication (FSOC) which now prevails more and more. The LCT is presently operated on satellites in Low Earth Orbit (LEO). In the near future, the LCT will be operated in Geosynchronous Orbit (GEO) onboard the ALPHASAT-TDP and the European Data Relay System (EDRS). In other words, the LCT has reached a point of maturity to realize its practical application. With existence of such space assets the time has come for other utilization beyond that of optical Inter-Satellite Links (ISL). Aeronautical applications, as for instance High Altitude Long Endurance (HALE) or Medium Altitude Long Endurance (MALE) Unmanned Aerial Systems (UAS) have to be addressed. This is caused due to an extremely high demand for bandwidth. Driving factors and advantages of FSOC in HALE/MALE UAS missions are highlighted. Numerous practice-related issues are described concerning the space segment, the aeronautical segment as well as the ground segment. The advantages for UAS missions are described resulting from the utilization of FSOC exclusively for wideband transmission of sensor data while vehicle Command & Control (C2) can be maintained, as before, via RF communication. Moreover, the paper discusses FSOC as an enabler for the integration of air and space-based wideband Intelligence, Surveillance & Reconnaissance (ISR) systems into existent military command and control networks. From the given information it can be concluded that FSOC contributes to the future increase of air-and space power.

Functional Significance of Single Nucleotide Polymorphisms in the Lactase Gene in Diverse United States Subjects and Evidence for a Novel Lactase Persistence Allele at -13909 in Those of European Ancestry

PubMed Central

Baffour-Awuah, Nana Yaa; Fleet, Sarah; Baker, Susan S.; Butler, Johannah L.; Campbell, Catarina; Tischfield, Samuel; Mitchell, Paul D.; Moon, Jennifer E.; Allende-Richter, Sophie; Fishman, Laurie; Bousvaros, Athos; Fox, Victor; Kuokkanen, Mikko; Montgomery, Robert K.; Grand, Richard J.; Hirschhorn, Joel N.

2014-01-01

Objectives Recent data from mainly homogeneous European and African populations implicate a 140 bp region 5′ to the transcriptional start site of LCT (the lactase gene) as a regulatory site for lactase persistence and non-persistence. As there are no studies of United States non-homogeneous populations, we performed genotype/phenotype analysis of the -13910 and -22018 LCT SNPs in New England children, mostly of European ancestry. Methods Duodenal biopsies were processed for disaccharidase activities, RNA quantification by RT-PCR, allelic expression ratios by PCR, and genotyping and SNP analysis. Results were compared to clinical information. Results Lactase activity and mRNA levels, as well as sucrase-to-lactase ratios of enzyme activity and mRNA, showed robust correlations with genotype. None of the other LCT SNPs showed as strong a correlation with enzyme or mRNA activities as did -13910. Data were consistent with the -13910 being the causal sequence variant rather than -22018. Four individuals heterozygous for -13910T/C had allelic expression patterns similar to individuals with -13910C/C genotypes; of these, 2 showed equal LCT expression from the 2 alleles and a novel variant (-13909C>A) associated with lactase persistence. Conclusion The identification of -13910C/C genotype is very likely to predict lactase non-persistence, consistent with prior published studies. A -13910T/T genotype will frequently, but not perfectly, predict lactase persistence in this mixed European-ancestry population; a -13910T/C genotype will not predict the phenotype. A long, rare haplotype in 2 individuals with -13910T/C genotype but equal allele-specific expression contains a novel lactase persistence allele present at -13909. PMID:25625576

Murine Vaginal Colonization Model for Investigating Asymptomatic Mucosal Carriage of Streptococcus pyogenes

PubMed Central

Watson, Michael E.; Nielsen, Hailyn V.; Hultgren, Scott J.

2013-01-01

While many virulence factors promoting Streptococcus pyogenes invasive disease have been described, specific streptococcal factors and host properties influencing asymptomatic mucosal carriage remain uncertain. To address the need for a refined model of prolonged S. pyogenes asymptomatic mucosal colonization, we have adapted a preestrogenized murine vaginal colonization model for S. pyogenes. In this model, derivatives of strains HSC5, SF370, JRS4, NZ131, and MEW123 established a reproducible, asymptomatic colonization of the vaginal mucosa over a period of typically 3 to 4 weeks' duration at a relatively high colonization efficiency. Prior treatment with estradiol prolonged streptococcal colonization and was associated with reduced inflammation in the colonized vaginal epithelium as well as a decreased leukocyte presence in vaginal fluid compared to the levels of inflammation and leukocyte presence in non-estradiol-treated control mice. The utility of our model for investigating S. pyogenes factors contributing to mucosal carriage was verified, as a mutant with a mutation in the transcriptional regulator catabolite control protein A (CcpA) demonstrated significant impairment in vaginal colonization. An assessment of in vivo transcriptional activity in the CcpA− strain for several known CcpA-regulated genes identified significantly elevated transcription of lactate oxidase (lctO) correlating with excessive generation of hydrogen peroxide to self-lethal levels. Deletion of lctO did not impair colonization, but deletion of lctO in a CcpA− strain prolonged carriage, exceeding even that of the wild-type strain. Thus, while LctO is not essential for vaginal colonization, its dysregulation is deleterious, highlighting the critical role of CcpA in promoting mucosal colonization. The vaginal colonization model should prove effective for future analyses of S. pyogenes mucosal colonization. PMID:23460515

Characterization of lactate utilization and its implication on the physiology of Haemophilus influenzae.

PubMed

Lichtenegger, Sabine; Bina, Isabelle; Roier, Sandro; Bauernfeind, Stilla; Keidel, Kristina; Schild, Stefan; Anthony, Mark; Reidl, Joachim

2014-05-01

Haemophilus influenzae is a Gram-negative bacillus and a frequent commensal of the human nasopharynx. Earlier work demonstrated that in H. influenzae type b, l-lactate metabolism is associated with serum resistance and in vivo survival of the organism. To further gain insight into lactate utilization of the non-typeable (NTHi) isolate 2019 and laboratory prototype strain Rd KW20, deletion mutants of the l-lactate dehydrogenase (lctD) and permease (lctP) were generated and characterized. It is shown, that the apparent KM of l-lactate uptake is 20.1μM as determined for strain Rd KW20. Comparison of the COPD isolate NTHi 2019-R with the corresponding lctP knockout strain for survival in human serum revealed no lactate dependent serum resistance. In contrast, we observed a 4-fold attenuation of the mutant strain in a murine model of nasopharyngeal colonization. Characterization of lctP transcriptional control shows that the lactate utilization system in H. influenzae is not an inductor inducible system. Rather negative feedback regulation was observed in the presence of l-lactate and this is dependent on the ArcAB regulatory system. Additionally, for 2019 it was found that lactate may have signaling function leading to increased cell growth in late log phase under conditions where no l-lactate is metabolized. This effect seems to be ArcA independent and was not observed in strain Rd KW20. We conclude that l-lactate is an important carbon-source and may act as host specific signal substrate which fine tunes the globally acting ArcAB regulon and may additionally affect a yet unknown signaling system and thus may contribute to enhanced in vivo survival. Copyright © 2014 Elsevier GmbH. All rights reserved.

Chinese hypertriglycerideamic subjects of different ages responded differently to consuming oil with medium- and long-chain fatty acids.

PubMed

Xue, Changyong; Liu, Yinghua; Wang, Jin; Zheng, Zixin; Zhang, Yuehong; Zhang, Yong; Zhang, Rongxin; Yu, Xiaoming; Jin, Hongjiang; Nosaka, Naohisa; Arai, Chie; Kasai, Michio; Aoyama, Toshiaki; Wu, Jian

2009-08-01

Two groups of Chinese hypertriacylglycerolemic subjects were recruited and randomized to medium- and long-chain triacylglycerols (MLCT) oil or long-chain triacylglycerols (LCT) oil. Two subgroups were divided by age at less or more 60 years in both groups. Both oils were consumed at 25-30 g daily for 8 weeks. Anthropometry, blood biochemicals, and computed tomography (CT) scanning were done at the initial and final times. In subjects of age less than 60 years on MLCT, the body weight, body mass index (BMI), waist circumference (WC), hip circumference (HC), waist-hip ratio (WHR), body fat, total fat area, and subcutaneous fat area were significantly lower than those of the initial values, and the change values in these indicators and visceral fat area lowered significantly as compared with those on LCT. The levels of apoB, apoA2, apoC2, and apoC3 decreased significantly, and the change in values in the levels of triglyceride (TG), low-density lipoprotein cholesterol (LDL-C), apoA1, apoB, apoA2, apoC2, apoC3 were significantly lower on MLCT of age under 60 years as compared with those on LCT.

Lactose Intolerance (LCT-13910C>T) Genotype Is Associated with Plasma 25-Hydroxyvitamin D Concentrations in Caucasians: A Mendelian Randomization Study.

PubMed

Alharbi, Ohood; El-Sohemy, Ahmed

2017-06-01

Background: The LCT -13910C>T gene variant is associated with lactose intolerance (LI) in different ethnic groups. Individuals with LI often limit or avoid dairy consumption, a major dietary source of vitamin D in North America, which may lead to inadequate vitamin D intake. Objective: The objective was to determine the prevalence of genotypes predictive of LI in different ethnic groups living in Canada and to determine whether the LCT genotype is associated with plasma 25(OH)D concentrations. Methods: Blood samples were drawn from a total of 1495 men and women aged 20-29 y from the Toronto Nutrigenomics and Health Study for genotyping and plasma 25(OH)D analysis. Intakes of dairy were assessed by using a 196-item food frequency questionnaire. The prevalence of LCT -13910C>T genotypes was compared by using χ 2 analysis. Using a Mendelian randomization approach, we examined the association between LCT genotypes and 25(OH)D concentrations. Results: Approximately 32% of Caucasians, 99% of East Asians, 74% of South Asians, and 59% of those with other or mixed ethnicities had the CC genotype associated with LI. Compared with those with the TT genotype, those with the CC genotype had a lower mean ± SE total dairy intake (2.15 ± 0.09 compared with 2.67 ± 0.12 servings/d, P = 0.003), a lower skim-milk intake (0.20 ± 0.03 compared with 0.46 ± 0.06 servings/d, P = 0.0004), and a lower plasma 25(OH)D concentration (63 ± 1.9 compared with 75.8 ± 2.4 nmol/L, P < 0.0001). The CT and CC genotypes were associated with a 50% and a 2-fold increased risk, respectively, of a suboptimal plasma 25(OH)D concentration (<75 nmol/L). Conclusions: In Caucasians, the CC genotype that predicts LI is associated with a lower plasma 25(OH)D concentration, which is attributable at least in part to a lower intake of dairy, particularly skim milk. Increased risk of suboptimal concentrations of vitamin D was also observed among those with the CT genotype, suggesting an intermediate effect of the heterozygous genotype. © 2017 American Society for Nutrition.

PET attenuation correction for flexible MRI surface coils in hybrid PET/MRI using a 3D depth camera

NASA Astrophysics Data System (ADS)

Frohwein, Lynn J.; Heß, Mirco; Schlicher, Dominik; Bolwin, Konstantin; Büther, Florian; Jiang, Xiaoyi; Schäfers, Klaus P.

2018-01-01

PET attenuation correction for flexible MRI radio frequency surface coils in hybrid PET/MRI is still a challenging task, as position and shape of these coils conform to large inter-patient variabilities. The purpose of this feasibility study is to develop a novel method for the incorporation of attenuation information about flexible surface coils in PET reconstruction using the Microsoft Kinect V2 depth camera. The depth information is used to determine a dense point cloud of the coil’s surface representing the shape of the coil. From a CT template—acquired once in advance—surface information of the coil is extracted likewise and converted into a point cloud. The two point clouds are then registered using a combination of an iterative-closest-point (ICP) method and a partially rigid registration step. Using the transformation derived through the point clouds, the CT template is warped and thereby adapted to the PET/MRI scan setup. The transformed CT template is converted into an attenuation map from Hounsfield units into linear attenuation coefficients. The resulting fitted attenuation map is then integrated into the MRI-based patient-specific DIXON-based attenuation map of the actual PET/MRI scan. A reconstruction of phantom PET data acquired with the coil present in the field-of-view (FoV), but without the corresponding coil attenuation map, shows large artifacts in regions close to the coil. The overall count loss is determined to be around 13% compared to a PET scan without the coil present in the FoV. A reconstruction using the new μ-map resulted in strongly reduced artifacts as well as increased overall PET intensities with a remaining relative difference of about 1% to a PET scan without the coil in the FoV.

Advances in Multi-Pixel Photon Counter technology: First characterization results

NASA Astrophysics Data System (ADS)

Bonanno, G.; Marano, D.; Romeo, G.; Garozzo, S.; Grillo, A.; Timpanaro, M. C.; Catalano, O.; Giarrusso, S.; Impiombato, D.; La Rosa, G.; Sottile, G.

2016-01-01

Due to the recent advances in silicon photomultiplier technology, new types of Silicon Photomultiplier (SiPM), also named Multi-Pixel Photon Counter (MPPC) detectors have become recently available, demonstrating superior performance in terms of their most important electrical and optical parameters. This paper presents the latest characterization results of the novel Low Cross-Talk (LCT) MPPC families from Hamamatsu, where a noticeable fill-factor enhancement and cross-talk reduction is achieved. In addition, the newly adopted resin coating has been proven to yield improved photon detection capabilities in the 280-320 nm spectral range, making the new LCT MPPCs particularly suitable for emerging applications like Cherenkov Telescope Array, and Astroparticle Physics.

Fast steering mirror for laser communication

NASA Astrophysics Data System (ADS)

Langenbach, Harald; Schmid, Manfred

2005-07-01

Future multimedia satellites require communication at large bandwidth which can be achieved by means of optical communication links. TESAT Spacecom is currently developing a Laser Communication Terminal (LCT) for such applications under DLR contract. EADS Astrium is developing and building the mechanisms for Pointing, Acquisition and Tracking (PAT) of the laser beam between two Laser Communication Terminals. Based on this development work the development of mechanism H/W to be flown on TerraSar X is currently under way. After a short description of the general arrangement of the Mechanisms inside the LCT, the paper describes the design of the fast steering mirrors (FSM) reflecting the critical requirements and the solutions how to achieve them.

Voice Coil Percussive Mechanism Concept for Hammer Drill

NASA Technical Reports Server (NTRS)

Okon, Avi

2009-01-01

A hammer drill design of a voice coil linear actuator, spring, linear bearings, and a hammer head was proposed. The voice coil actuator moves the hammer head to produce impact to the end of the drill bit. The spring is used to store energy on the retraction and to capture the rebound energy after each impact for use in the next impact. The maximum actuator stroke is 20 mm with the hammer mass being 200 grams. This unit can create impact energy of 0.4 J with 0.8 J being the maximum. This mechanism is less complex than previous devices meant for the same task, so it has less mass and less volume. Its impact rate and energy are easily tunable without changing major hardware components. The drill can be driven by two half-bridges. Heat is removed from the voice coil via CO2 conduction.

A conceptual design study of a high temperature solar thermal receiver (added tasks 6 and 7)

NASA Technical Reports Server (NTRS)

Robertson, C. S.; Mccreight, L. R.; Gatti, A.; Semon, H. W.

1980-01-01

The key component of this concept is a coiled tube of silicon nitride which acts as a heat exchanger appears to be ideal from the standpoint of utilizing structural ceramics at around 2500 F under severe thermal shock conditions. However the size and configuration of this coil are beyond the state of the art for fabricating such materials as silicon nitride and carbide. A two-task program to develop and demonstrate the feasibility of extruding and forming a section of thin walled silicon nitride tubing was undertaken as an addition to the original program. A promising polyvinyl butyral-based binder lubricant was identified. Fourteen full size extrusion experiments were conducted. Two trial firings of 1-1/4 turn helices were made.

Preventive Effects of the Dietary Intake of Medium-chain Triacylglycerols on Immobilization-induced Muscle Atrophy in Rats.

PubMed

Nishimura, Shuhei; Inai, Makoto; Takagi, Tetsuo; Nonaka, Yudai; Urashima, Shogo; Honda, Kazumitsu; Aoyama, Toshiaki; Terada, Shin

2017-08-01

Previous studies have shown that medium-chain triacylglycerols (MCTs) exert favorable effects on protein metabolism. This study evaluated the effects of the dietary intake of MCTs on rat skeletal muscle mass and total protein content during casting-induced hindlimb immobilization, which causes substantial protein degradation and muscle atrophy. Rats were fed a standard diet containing long-chain triacylglycerols (LCTs) or MCTs for 3 days and then a unilateral hindlimb was immobilized while they received the same diet. After immobilization for 3, 7, and 14 days, muscle mass and total protein content in immobilized soleus muscle in the LCT-fed rats had markedly decreased compared to the contralateral muscle; however, these losses were partially suppressed in MCT-fed rats. Autophagosomal membrane proteins (LC-I and -II), which are biomarkers of autophagy-lysosome activity, did not differ significantly between the LCT- and MCT-fed rats. In contrast, the immobilization-induced increase in muscle-specific E3 ubiquitin ligase MuRF-1 protein expression in immobilized soleus muscle relative to contralateral muscle was completely blocked in the MCT-fed rats and was significantly lower than that observed in the LCT-fed rats. Collectively, these results indicate that the dietary intake of MCTs at least partly alleviates immobilization-induced muscle atrophy by inhibiting the ubiquitin-proteasome pathway.

Studies on self-nanoemulsifying drug delivery system of flurbiprofen employing long, medium and short chain triglycerides.

PubMed

Daar, Junaid; Khan, Ahmad; Khan, Jallat; Khan, Amjad; Khan, Gul Majid

2017-03-01

The aim of the study was to successfully design, formulate and evaluate self-nanoemulsifying drug delivery system (SNEDDS) of poorly aqueous soluble drug viz. flurbiprofen using long (LCT), medium (MCT) and short chain triglycerides (SCT). The SNEDDS are thermodynamically stable lipid based drug delivery systems which consist of mixture of oil, surfactant and co-surfactant. Upon aqueous dilution, this mixture produces nano-emulsion spontaneously on slight agitation. The excipients intended to be used were screened for their potential to dissolve the drug and to form clear dispersion upon aqueous dilution. Labrafil M 1944 CS, capryol-90 and triacetin were selected as long, medium and short chain triglycerides, respectively, as lipids while tween-80 and polyethylene glycol-400 (PEG-400)/ethanol (3:1 ratio) were selected as surfactant and co-surfactant, respectively. The excipients were studied at every possible combination ratios using pseudo-ternary diagram. The LCT, MCT and SCT-SNEDDS were optimized using thermodynamic studies, percentage transmittance value, viscosity, refractive index (RI), electrical conductivity, globule size analysis and in-vitro drug release studies. The drug release profiles of optimized SNEDDS were then compared with market product at different pH mediums. The LCT-SNEDDS was considered to be superior for enhancement of the drug bioavailability when compared with other SNEDDS formulations and market product.

Lactococcus lactis LMG2081 Produces Two Bacteriocins, a Nonlantibiotic and a Novel Lantibiotic

PubMed Central

Mirkovic, Nemanja; Polovic, Natalija; Vukotic, Goran; Jovcic, Branko; Miljkovic, Marija; Radulovic, Zorica; Diep, Dzung B.

2016-01-01

Bacteriocin producers normally possess dedicated immunity systems to protect themselves from their own bacteriocins. Lactococcus lactis strains LMG2081 and BGBM50 are known as lactococcin G producers. However, BGBM50 was sensitive to LMG2081, which indicated that LMG2081 might produce additional bacteriocins that are not present in BGBM50. Therefore, whole-genome sequencing of the two strains was performed, and a lantibiotic operon (called lctLMG) was identified in LMG2081 but not in BGBM50. The lctLMG operon contains six open reading frames; the first three genes, lmgA, lmgM, and lmgT, are involved in the biosynthesis and export of bacteriocin, while the other three genes, lmgF, lmgE, and lmgG, are involved in lantibiotic immunity. Mutational analysis confirmed that the lctLMG operon is responsible for the additional antimicrobial activity. Specifically, site-directed mutation within this operon rendered LMG2081 inactive toward BGBM50. Subsequent purification and electrospray ionization–time of flight mass spectrometric analysis confirmed that the lantibiotic bacteriocin called lacticin LMG is exported as a 25-amino-acid peptide. Lacticin LMG is highly similar to the lacticin 481 group. It is interesting that a bacteriocin producer produces two different classes of bacteriocins, whose operons are located in the chromosome and a plasmid. PMID:26896142

Transcriptomic and proteomic responses of Serratia marcescens to spaceflight conditions involve large-scale changes in metabolic pathways

NASA Astrophysics Data System (ADS)

Wang, Yajuan; Yuan, Yanting; Liu, Jinwen; Su, Longxiang; Chang, De; Guo, Yinghua; Chen, Zhenhong; Fang, Xiangqun; Wang, Junfeng; Li, Tianzhi; Zhou, Lisha; Fang, Chengxiang; Yang, Ruifu; Liu, Changting

2014-04-01

The microgravity environment of spaceflight expeditions has been associated with altered microbial responses. This study explores the characterization of Serratia marcescensis grown in a spaceflight environment at the phenotypic, transcriptomic and proteomic levels. From November 1, 2011 to November 17, 2011, a strain of S. marcescensis was sent into space for 398 h on the Shenzhou VIII spacecraft, and ground simulation was performed as a control (LCT-SM213). After the flight, two mutant strains (LCT-SM166 and LCT-SM262) were selected for further analysis. Although no changes in the morphology, post-culture growth kinetics, hemolysis or antibiotic sensitivity were observed, the two mutant strains exhibited significant changes in their metabolic profiles after exposure to spaceflight. Enrichment analysis of the transcriptome showed that the differentially expressed genes of the two spaceflight strains and the ground control strain mainly included those involved in metabolism and degradation. The proteome revealed that changes at the protein level were also associated with metabolic functions, such as glycolysis/gluconeogenesis, pyruvate metabolism, arginine and proline metabolism and the degradation of valine, leucine and isoleucine. In summary S. marcescens showed alterations primarily in genes and proteins that were associated with metabolism under spaceflight conditions, which gave us valuable clues for future research.

Genetic predisposition for adult lactose intolerance and relation to diet, bone density, and bone fractures.

PubMed

Obermayer-Pietsch, Barbara M; Bonelli, Christine M; Walter, Daniela E; Kuhn, Regina J; Fahrleitner-Pammer, Astrid; Berghold, Andrea; Goessler, Walter; Stepan, Vinzenz; Dobnig, Harald; Leb, Georg; Renner, Wilfried

2004-01-01

Evidence that genetic disposition for adult lactose intolerance significantly affects calcium intake, bone density, and fractures in postmenopausal women is presented. PCR-based genotyping of lactase gene polymorphisms may complement diagnostic procedures to identify persons at risk for both lactose malabsorption and osteoporosis. Lactase deficiency is a common autosomal recessive condition resulting in decreased intestinal lactose degradation. A -13910 T/C dimorphism (LCT) near the lactase phlorizin hydrolase gene, reported to be strongly associated with adult lactase nonpersistence, may have an impact on calcium supply, bone density, and osteoporotic fractures in the elderly. We determined LCT genotypes TT, TC, and CC in 258 postmenopausal women using a polymerase chain reaction-based assay. Genotypes were related to milk intolerance, nutritional calcium intake, intestinal calcium absorption, bone mineral density (BMD), and nonvertebral fractures. Twenty-four percent of all women were found to have CC genotypes and genetic lactase deficiency. Age-adjusted BMD at the hip in CC genotypes and at the spine in CC and TC genotypes was reduced by -7% to -11% depending on the site measured (p = 0.04). LCT(T/C-13910) polymorphisms alone accounted for 2-4% of BMD in a multiple regression model. Bone fracture incidence was significantly associated with CC genotypes (p = 0.001). Milk calcium intake was significantly lower (-55%, p = 0.004) and aversion to milk consumption was significantly higher (+166%, p = 0.01) in women with the CC genotype, but there were no differences in overall dietary calcium intake or in intestinal calcium absorption test values. The LCT(T/C-13910) polymorphism is associated with subjective milk intolerance, reduced milk calcium intake, and reduced BMD at the hip and the lumbar spine and may predispose to bone fractures. Genetic testing for lactase deficiency may complement indirect methods in the detection of individuals at risk for both lactose malabsorption and osteoporosis.

Endogenous fat oxidation during medium chain versus long chain triglyceride feeding in healthy women.

PubMed

Papamandjaris, A A; White, M D; Raeini-Sarjaz, M; Jones, P J

2000-09-01

To compare the effect of medium chain triglycerides (MCT) vs long chain triglycerides (LCT) feeding on exogenous and endogenous oxidation of long chain saturated fatty acids (LCSFA) in women. Twelve healthy female subjects (age 19-26 y, body mass index (BMI) 17.5-28.6 kg/m2) In a randomized cross-over design, subjects were fed weight maintenance diets providing 15%, 45% and 40% of energy as protein, carbohydrate and fat, respectively, with 80% of this fat comprising either a combination of butter and coconut oil (MCT) or beef tallow (LCT). Following 6 days of feeding, subjects were given daily oral doses of 1-(13)C labelled-myristic, -palmitic and -stearic acids for 8 days. Expired 13CO2 was used as an index of LCSFA oxidation with CO2 production assessed by respiratory gas exchange. No difference in exogenous LCSFA oxidation was observed as a function of diet on day 7. On day 14, greater combined cumulative fractional LCSFA oxidation (16.9 +/- 2.5%/5.5 h vs 9.1 +/- 1.2%/5.5 h, P < 0.007), net LCSFA oxidation (2956 +/- 413 mg/5.5 h vs 1669 +/- 224 mg/5.5 h, P < 0.01), and percentage dietary LCSFA contribution to total fat oxidation (16.3 +/- 2.3%/5.5 h vs 9.5 +/- 1.5%/5.5 h; P < 0.01) were observed in women fed the MCT vs LCT diet. With the MCT diet, but not the LCT diet, combined cumulative fractional LCSFA oxidation (P < 0.03), net LCSFA oxidation (P < 0.03), and percentage dietary LCSFA contribution to total fat oxidation (P < 0.02) were increased at day 14 as compared to day 7. Day 14 results indicated increased endogenous LCSFA oxidation during MCT feeding. The capacity of MCT to increase endogenous oxidation of LCSFA suggests a role for MCT in body weight control over the long term.

Spatially resolved vertical vorticity in solar supergranulation using helioseismology and local correlation tracking

NASA Astrophysics Data System (ADS)

Langfellner, J.; Gizon, L.; Birch, A. C.

2015-09-01

Flow vorticity is a fundamental property of turbulent convection in rotating systems. Solar supergranules exhibit a preferred sense of rotation, which depends on the hemisphere. This is due to the Coriolis force acting on the diverging horizontal flows. We aim to spatially resolve the vertical flow vorticity of the average supergranule at different latitudes, both for outflow and inflow regions. To measure the vertical vorticity, we use two independent techniques: time-distance helioseismology (TD) and local correlation tracking of granules in intensity images (LCT) using data from the Helioseismic and Magnetic Imager (HMI) on board the Solar Dynamics Observatory (SDO). Both maps are corrected for center-to-limb systematic errors. We find that 8 h TD and LCT maps of vertical vorticity are highly correlated at large spatial scales. Associated with the average supergranule outflow, we find tangential (vortical) flows that reach about 10 m s-1 in the clockwise direction at 40° latitude. In average inflow regions, the tangential flow reaches the same magnitude, but in the anticlockwise direction. These tangential velocities are much smaller than the radial (diverging) flow component (300 m s-1 for the average outflow and 200 m s-1 for the average inflow). The results for TD and LCT as measured from HMI are in excellent agreement for latitudes between -60° and 60°. From HMI LCT, we measure the vorticity peak of the average supergranule to have a full width at half maximum of about 13 Mm for outflows and 8 Mm for inflows. This is larger than the spatial resolution of the LCT measurements (about 3 Mm). On the other hand, the vorticity peak in outflows is about half the value measured at inflows (e.g., 4 × 10-6 s-1 clockwise compared to 8 × 10-6 s-1 anticlockwise at 40° latitude). Results from the Michelson Doppler Imager (MDI) on board the Solar and Heliospheric Observatory (SOHO) obtained in 2010 are biased compared to the HMI/SDO results for the same period. Appendices are available in electronic form at http://www.aanda.orgThe azimuthally averaged velocity components vr and vt for supergranular outflows and inflows at various latitudes are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/581/A67

Applications of the chemical oxygen-iodine laser

NASA Astrophysics Data System (ADS)

Latham, W. Pete; Kendrick, Kip R.; Quillen, Brian

2000-01-01

The Chemical Oxygen-Iodine Laser (COIL) has been developed at the Air Force Research Laboratory for military applications. For example, the COIL is to be use as the laser device for the ABL. A high power laser is useful for applications that require the delivery of a substantial amount of energy to a very small focused laser spot. The COIL is a member of the class of high power lasers that are also useful for industrial applications, including the materials processing task of high speed cutting and drilling. COIL technology has received considerable interest over the last several years due to its short, fiber- deliverable wavelength, scalability to very high powers, and demonstrated nearly diffraction-limited optical quality. These unique abilities make it an ideal candidate for nuclear reactor decommissioning and nuclear warhead dismantlement. Japanese researchers envision using a COIL for disaster cleanup and survivor rescue. It is also being studied by the oil and gas industry for well drilling. Any commercial or industrial application that requires very rapid, precise, and noninvasive cutting or drilling, could be readily accomplished with a COIL. Because of the substantial power levels available with a COIL, the laser could also be used for broad area applications such as paint stripping. This paper includes a collection of experiments accomplished at the Air Force Research Laboratory Chemical Laser Facility, including metal cutting, hole drilling, high power fiber optic transmission, and rock crushing.

Assessing Understanding of the Learning Cycle: The ULC

NASA Astrophysics Data System (ADS)

Marek, Edmund A.; Maier, Steven J.; McCann, Florence

2008-08-01

An 18-item, multiple choice, 2-tiered instrument designed to measure understanding of the learning cycle (ULC) was developed and field-tested from the learning cycle test (LCT) of Odom and Settlage ( Journal of Science Teacher Education, 7, 123 142, 1996). All question sets of the LCT were modified to some degree and 5 new sets were added, resulting in the ULC. The ULC measures (a) understandings and misunderstandings of the learning cycle, (b) the learning cycle’s association with Piaget’s ( Biology and knowledge theory: An essay on the relations between organic regulations and cognitive processes, 1975) theory of mental functioning, and (c) applications of the learning cycle. The resulting ULC instrument was evaluated for internal consistency with Cronbach’s alpha, yielding a coefficient of .791.

An 8/15-channel Tx/Rx head neck RF coil combination with region-specific B1 + shimming for whole-brain MRI focused on the cerebellum at 7T.

PubMed

Pfaffenrot, Viktor; Brunheim, Sascha; Rietsch, Stefan H G; Koopmans, Peter J; Ernst, Thomas M; Kraff, Oliver; Orzada, Stephan; Quick, Harald H

2018-02-09

To design and evaluate an 8/15-channel transmit/receive (Tx/Rx) head-neck RF coil combination with region-specific B1+ shimming for whole-brain MRI with focus on improved functional MRI of the cerebellum at 7 T. An 8-channel transceiver RF head coil was combined with a 7-channel receive-only array. The noise parameters and acceleration capabilities of this 8Tx/15Rx coil setup were compared with a commercially available 1Tx/32Rx RF head coil. Region-specific 8-channel B1+ shimming was applied when using the 8Tx/15Rx RF coil. To evaluate the capability for functional MRI of the cerebellum, temporal SNR and statistical nonparametric maps for finger-tapping experiments with 14 healthy subjects were derived by applying a variable slice thickness gradient-echo echo-planar functional MRI sequence. The 8Tx/15Rx setup had a lower maximum noise correlation between channels, but higher average correlations compared with the 1Tx/32Rx coil. Both RF coils exhibited identical g-factors in the cerebellum with R = 3 acceleration. The enlarged FOV of the 8Tx/15Rx coil in combination with region-specific B1+ shimming increased homogeneity of the transmission field and temporal SNR in caudal cerebellar regions. Temporal SNR losses in cranial parts were reduced, resulting in more highly significant voxels in the caudally activated areas and identical patterns in the cranial cerebellar parts during a finger-tapping task. Compared with the 1Tx/32Rx RF coil, the presented 8Tx/15Rx RF coil combination successfully improves functional MRI of the human cerebellum at 7 T while maintaining whole-brain coverage. A clear temporal SNR gain in caudal cerebellar regions is shown. © 2018 International Society for Magnetic Resonance in Medicine.

Assessment of vitamin D status and serum CrossLaps levels in adults with primary lactose malabsorption.

PubMed

Enko, D; Kriegshäuser, G; Stolba, R; Mangge, H; Brandstetter, D; Mayr, N; Forstner, T; Halwachs-Baumann, G

2016-09-01

Primary adult-type lactose malabsorption (PALM) is a widespread inherited autosomal recessive condition, which is considered to be associated with osteoporosis. This prospective study aimed at assessing the 25-hydroxy-vitamin D (25(OH)D) status and serum CrossLaps levels in individuals with PALM and normal controls. All participants (n=210) underwent genotyping for the LCT C/T-13910 polymorphism, 25(OH)D and CrossLaps measurements and clinical examinations. In addition, the anthropometric data (that is, height, weight and body mass index) were determined. Fifty-five individuals with PALM (that is, LCT C/C-13910 homozygotes) showed lower 25(OH)D (mean: 24.95±10.04 vs 28.59±9.56 ng/ml, P=0.018) and higher CrossLaps serum levels (mean: 0.46±0.31 vs 0.43±0.49 ng/ml, P=0.251) compared with 155 normal controls (that is, LCT C/T-13910 hetero- or T/T-13910 homozygotes). Anthropometric data were similar between PALM probands and controls. Individuals with PALM were found to have lower 25(OH)D and higher CrossLaps serum levels compared with normal controls. In order to preserve life-long bone health, routine 25(OH)D and CrossLaps serum measurements should be performed in individuals with PALM.

Lactococcus lactis LMG2081 Produces Two Bacteriocins, a Nonlantibiotic and a Novel Lantibiotic.

PubMed

Mirkovic, Nemanja; Polovic, Natalija; Vukotic, Goran; Jovcic, Branko; Miljkovic, Marija; Radulovic, Zorica; Diep, Dzung B; Kojic, Milan

2016-04-01

Bacteriocin producers normally possess dedicated immunity systems to protect themselves from their own bacteriocins.Lactococcus lactis strains LMG2081 and BGBM50 are known as lactococcin G producers. However, BGBM50 was sensitive to LMG2081, which indicated that LMG2081 might produce additional bacteriocins that are not present in BGBM50. Therefore, whole-genome sequencing of the two strains was performed, and a lantibiotic operon (called lctLMG) was identified in LMG2081 but not in BGBM50. The lctLMG operon contains six open reading frames; the first three genes,lmgA ,lmgM, and lmgT, are involved in the biosynthesis and export of bacteriocin, while the other three genes,lmgF,lmgE, and lmgG, are involved in lantibiotic immunity. Mutational analysis confirmed that the lctLMG operon is responsible for the additional antimicrobial activity. Specifically, site-directed mutation within this operon rendered LMG2081 inactive toward BGBM50. Subsequent purification and electrospray ionization-time of flight mass spectrometric analysis confirmed that the lantibiotic bacteriocin called lacticin LMG is exported as a 25-amino-acid peptide. Lacticin LMG is highly similar to the lacticin 481 group. It is interesting that a bacteriocin producer produces two different classes of bacteriocins, whose operons are located in the chromosome and a plasmid. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Cellular and physiological effects of medium-chain triglycerides.

PubMed

Wanten, Geert J; Naber, Anton H

2004-10-01

From a nutritional standpoint, saturated triglycerides with a medium (6 to 12) carbon chain length (MCT) have traditionally been regarded as biologically inert substances, merely serving as a source of fuel calories that is relatively easily accessible for metabolic breakdown compared with long chain triglycerides (LCT). This quality of MCT has been shown to offer both benefits and risks depending on the clinical situation, with potential positive effects on protein metabolism in some studies on one side, and an increased risk for ketogenesis and metabolic acidosis on the other. At another level, studies regarding lipid effects of MCT on the immune system, as with LCT, so far have yielded equivocal results, although there is a recent experimental evidence to suggest that MCT possess immune modulating properties and should in fact be regarded as bioactive mediators. Most of this information comes from studies where effects of MCT have been compared with those of LCT in lipid emulsions, as part of parenteral (intravenous) nutrition formulations. Unfortunately, the relevance of these observations for clinical practice remains largely unclear because adequately powered trials that clearly point out the position of MCT in relation to structurally different lipids have not been performed. In the present paper we review the experimental and clinical evidence for cellular and physiological effects of nutritional MCT. In addition, studies describing possible mechanisms behind the observed effects of MCT will be discussed.

First evidence of an extensive Acheulean large cutting tool accumulation in Europe from Porto Maior (Galicia, Spain).

PubMed

Méndez-Quintas, E; Santonja, M; Pérez-González, A; Duval, M; Demuro, M; Arnold, L J

2018-02-15

We describe a European Acheulean site characterised by an extensive accumulation of large cutting tools (LCT). This type of Lower Paleolithic assemblage, with dense LCT accumulations, has only been found on the African continent and in the Near East until now. The identification of a site with large accumulations of LCTs favours the hypothesis of an African origin for the Acheulean of Southwest Europe. The lithic tool-bearing deposits date back to 293-205 thousand years ago. Our chronological findings confirm temporal overlap between sites with clear "African" Acheulean affinities and Early Middle Paleolithic sites found elsewhere in the region. These complex technological patterns could be consistent with the potential coexistence of different human species in south-western Europe during the Middle Pleistocene.

Multi-Coil Shimming of the Mouse Brain

PubMed Central

Juchem, Christoph; Brown, Peter B.; Nixon, Terence W.; McIntyre, Scott; Rothman, Douglas L.; de Graaf, Robin A.

2011-01-01

MR imaging and spectroscopy allow the non-invasive measurement of brain function and physiology, but excellent magnetic field homogeneity is required for meaningful results. The homogenization of the magnetic field distribution in the mouse brain (i.e. shimming) is a difficult task due to complex susceptibility-induced field distortions combined with the small size of the object. To date, the achievement of satisfactory whole brain shimming in the mouse remains a major challenge. The magnetic fields generated by a set of 48 circular coils (diameter 13 mm) that were arranged in a cylinder-shaped pattern of 32 mm diameter and driven with individual dynamic current ranges of ±1 A are shown to be capable of substantially reducing the field distortions encountered in the mouse brain at 9.4 Tesla. Static multi-coil shim fields allowed the reduction of the standard deviation of Larmor frequencies by 31% compared to second order spherical harmonics shimming and a 66% narrowing was achieved with the slice-specific application of the multi-coil shimming with a dynamic approach. For gradient echo imaging, multi-coil shimming minimized shim-related signal voids in the brain periphery and allowed overall signal gains of up to 51% compared to spherical harmonics shimming. PMID:21442653

Electromagnetic launchers

NASA Astrophysics Data System (ADS)

Kolm, H.; Mongeau, P.; Williams, F.

1980-09-01

Recent advances in energy storage, switching and magnet technology make electromagnetic acceleration a viable alternative to chemical propulsion for certain tasks, and a means to perform other tasks not previously feasible. Applications include the acceleration of gram-size particles for hypervelocity research and the initiation of fusion by impact, a replacement for chemically propelled artillery, the transportation of cargo and personnel over inaccessible terrain, and the launching of space vehicles to supply massive space operations, and for the disposal of nuclear waste. The simplest launcher of interest is the railgun, in which a short-circuit slide or an arc is driven along two rails by direct current. The most sophisticated studied thus far is the mass driver, in which a superconducting shuttle bucket is accelerated by a line of pulse coils energized by capacitors at energy conversion efficiencies better than 90%. Other accelerators of interest include helical, brush-commutated motors, discrete coil arc commutated drivers, flux compression momentum transformers, and various hybrid electrochemical devices.

Impaired Neurobehavioural Performance in Untreated Obstructive Sleep Apnea Patients Using a Novel Standardised Test Battery.

PubMed

D'Rozario, Angela L; Field, Clarice J; Hoyos, Camilla M; Naismith, Sharon L; Dungan, George C; Wong, Keith K H; Grunstein, Ronald R; Bartlett, Delwyn J

2018-01-01

Although polysomnography (PSG) is the gold-standard measure for assessing disease severity in obstructive sleep apnea (OSA), it has limited value in identifying individuals experiencing significant neurobehavioural dysfunction. This study used a brief and novel computerised test battery to examine neurobehavioural function in adults with and without OSA. 204 patients with untreated OSA [age 49.3 (12.5) years; body mass index, [BMI] 33.6 (8.0) kg/m 2 ; Epworth sleepiness scale 12 (4.9)/24; apnea hypopnea index 33.6 (25.8)/h] and 50 non-OSA participants [age 39.2 (14.0) years; BMI 25.8 (4.2) kg/m 2 , ESS 3.6 (2.3)/24]. All participants completed a computerised neurobehavioural battery during the daytime in the sleep clinic. The OSA group subsequently underwent an overnight PSG. The 30 min test battery assessed cognitive domains of visual spatial scanning and selective attention (Letter Cancellation Test), executive function (Stroop task) and working memory (2- and 3-Back tasks), and a validated sustained attention task (psychomotor vigilance task, PVT). Group differences in performance were compared. Associations between disease severity and performance were examined in the OSA group. After controlling for age, gender and education, OSA patients demonstrated impaired performance on the Stroop-Text, 2 and 3-Back tasks, and the PVT compared with the non-OSA group. OSA patients had worse performance on the LCT with fewer average hits albeit with better accuracy. Some OSA polysomnographic disease severity measures were weakly correlated with performance. This brief test battery may provide a sensitive, standardised method of assessing daytime dysfunction in OSA.

Lower critical temperature and cold-induced thermogenesis of lean and overweight humans are inversely related to body mass and basal metabolic rate.

PubMed

Nahon, Kimberly J; Boon, Mariëtte R; Doornink, Fleur; Jazet, Ingrid M; Rensen, Patrick C N; Abreu-Vieira, Gustavo

2017-10-01

It is colloquially stated that body size plays a role in the human response to cold, but the magnitude and details of this interaction are unclear. To explore the inherent influence of body size on cold-exposed metabolism, we investigated the relation between body composition and resting metabolic rate in humans at thermoneutrality and during cooling within the nonshivering thermogenesis range. Body composition and resting energy expenditure were measured in 20 lean and 20 overweight men at thermoneutrality and during individualized cold exposure. Metabolic rates as a function of ambient temperature were investigated considering the variability in body mass and composition. We observed an inverse relationship between body size and the lower critical temperature (LCT), i.e. the threshold where thermoneutrality ends and cold activates thermogenesis. LCT was higher in lean than overweight subjects (22.1 ± 0.6 vs 19.5 ± 0.5°C, p < 0.001). Below LCT, minimum conductance was identical between lean and overweight (100 ± 4 vs 97 ± 3kcal/°C/day respectively, p = 0.45). Overweight individuals had higher basal metabolic rate (BMR) explained mostly by the higher lean mass, and lower cold-induced thermogenesis (CIT) per degree of cold exposure. Below thermoneutrality, energy expenditure did not scale to lean body mass. Overweight subjects had lower heat loss per body surface area (44.7 ± 1.3 vs 54.7 ± 2.3kcal/°C/m 2 /day, p < 0.001). We conclude that larger body sizes possessed reduced LCT as explained by higher BMR related to more lean mass rather than a change in whole-body conductance. Thus, larger individuals with higher lean mass need to be exposed to colder temperatures to activate CIT, not because of increased insulation, but because of a higher basal heat generation. Our study suggests that the distinct effects of body size and composition on energy expenditure should be taken in account when exploring the metabolism of humans exposed to cold. Copyright © 2017 Elsevier Ltd. All rights reserved.

Field-Scale Modeling of Local Capillary Trapping During CO2 Injection into a Saline Aquifer

NASA Astrophysics Data System (ADS)

Ren, B.; Lake, L. W.; Bryant, S. L.

2015-12-01

Local capillary trapping is the small-scale (10-2 to 10+1 m) CO2 trapping that is caused by the capillary pressure heterogeneity. The benefit of LCT, applied specially to CO2 sequestration, is that saturation of stored CO2 is larger than the residual gas, yet these CO2 are not susceptible to leakage through failed seals. Thus quantifying the extent of local capillary trapping is valuable in design and risk assessment of geologic storage projects. Modeling local capillary trapping is computationally expensive and may even be intractable using a conventional reservoir simulator. In this paper, we propose a novel method to model local capillary trapping by combining geologic criteria and connectivity analysis. The connectivity analysis originally developed for characterizing well-to-reservoir connectivity is adapted to this problem by means of a newly defined edge weight property between neighboring grid blocks, which accounts for the multiphase flow properties, injection rate, and gravity effect. Then the connectivity is estimated from shortest path algorithm to predict the CO2 migration behavior and plume shape during injection. A geologic criteria algorithm is developed to estimate the potential local capillary traps based only on the entry capillary pressure field. The latter is correlated to a geostatistical realization of permeability field. The extended connectivity analysis shows a good match of CO2 plume computed by the full-physics simulation. We then incorporate it into the geologic algorithm to quantify the amount of LCT structures identified within the entry capillary pressure field that can be filled during CO2 injection. Several simulations are conducted in the reservoirs with different level of heterogeneity (measured by the Dykstra-Parsons coefficient) under various injection scenarios. We find that there exists a threshold Dykstra-Parsons coefficient, below which low injection rate gives rise to more LCT; whereas higher injection rate increases LCT in heterogeneous reservoirs. Both the geologic algorithm and connectivity analysis are very fast; therefore, the integrated methodology can be used as a quick tool to estimate local capillary trapping. It can also be used as a potential complement to the full-physics simulation to evaluate safe storage capacity.

Structured triglycerides were well tolerated and induced increased whole body fat oxidation compared with long-chain triglycerides in postoperative patients.

PubMed

Sandström, R; Hyltander, A; Körner, U; Lundholm, K

1995-01-01

It has been proposed, on the basis of animal experiments, that medium-chain triglycerides (MCT) may exert more favorable effects on whole body metabolism of injured animals than long-chain triglycerides (LCT). Therefore, the present study was designed to evaluate whether structured triglycerides are associated with increased whole body fat oxidation without promotion of ketogenesis in postoperative patients. A structured lipid emulsion (73403 Pharmacia, Sweden) containing medium- and long-chain fatty acids, esterified randomly to glycerol in a triglyceride structure, was used. Whole body fat oxidation was determined by indirect calorimetry in the postoperative period. Patients were randomized to receive structured lipids 1 day followed by LCT (Intralipid, Pharmacia) the next day or vice versa during 6 postoperative days. In part 1 of the study patients received fat at 1.0 g/kg per day in the presence of 80% of the basal requirement of nonprotein calories. In part 2 patients received fat at 1.5 g/kg per day in the presence of 120% of the nonprotein caloric requirement. Amino acids were always provided at 0.15 g N/kg per day. Structured lipids were not associated with any side effects, were rapidly cleared from the plasma compartment, and were rapidly oxidized without any significant hyperlipidemia or ketosis. Provision of structured lipids in the presence of excess of nonprotein calories (part 2) caused a significantly higher whole body fat oxidation (2.4 +/- 0.05 g/kg per day) compared with LCT provision (1.9 +/- 0.06 g/kg per day) (p < .0001) examined in the same patients. The results demonstrated for the first time in man that provision of structured triglycerides were associated with increased whole body fat oxidation in stressed postoperative patients, which is in line with the original metabolic and biochemical concept for structured triglycerides. The study provided evidence to support that structured lipids may represent a next generation of IV fat emulsions that may be clinically advantageous compared with conventional LCT emulsions in certain clinical conditions.

Stellarator Saddle Coils

NASA Astrophysics Data System (ADS)

Boozer, Allen H.

1999-11-01

Modern stellarators are designed using J. Nuehrenberg’s method of varying Fourier coefficients in the shape of the plasma boundary to maximize a target function. The matrix of second derivatives of the target function at the optimum determines a quality matrix. This matrix gives the degradation in the quality of the configuration as the normal magnetic field is varied on a control surface, which lies on or outside the plasma surface. The task is finding saddle coils that produce the desired configuration in the presence of a given toroidal field. An eigenvector of the quality matrix can be important for two reasons: (1) the normal field that must be produced by the saddles is large or (2) the eigenvalue is large (an island-causing resonant perturbation). The rank of the important part of the quality matrix is the number of important eigenvectors. The current in each saddle coil produces a normal field on the control surface, which can be described by an inductance matrix. The relevant part of the inductance matrix has large eigenvalues. The coils can produce the configuration if the rank of the important part of the quality matrix and its product with the relevant part of the inductance matrix are the same. Existing coil design codes, pioneered by P. Merkel, approximate the quality matrix by the unit matrix. Stellarator flexibility could be enhanced by using a more realistic quality matrix and by using trim coils to balance large eigenvalues.

Improving the spatial accuracy in functional magnetic resonance imaging (fMRI) based on the blood oxygenation level dependent (BOLD) effect: benefits from parallel imaging and a 32-channel head array coil at 1.5 Tesla.

PubMed

Fellner, C; Doenitz, C; Finkenzeller, T; Jung, E M; Rennert, J; Schlaier, J

2009-01-01

Geometric distortions and low spatial resolution are current limitations in functional magnetic resonance imaging (fMRI). The aim of this study was to evaluate if application of parallel imaging or significant reduction of voxel size in combination with a new 32-channel head array coil can reduce those drawbacks at 1.5 T for a simple hand motor task. Therefore, maximum t-values (tmax) in different regions of activation, time-dependent signal-to-noise ratios (SNR(t)) as well as distortions within the precentral gyrus were evaluated. Comparing fMRI with and without parallel imaging in 17 healthy subjects revealed significantly reduced geometric distortions in anterior-posterior direction. Using parallel imaging, tmax only showed a mild reduction (7-11%) although SNR(t) was significantly diminished (25%). In 7 healthy subjects high-resolution (2 x 2 x 2 mm3) fMRI was compared with standard fMRI (3 x 3 x 3 mm3) in a 32-channel coil and with high-resolution fMRI in a 12-channel coil. The new coil yielded a clear improvement for tmax (21-32%) and SNR(t) (51%) in comparison with the 12-channel coil. Geometric distortions were smaller due to the smaller voxel size. Therefore, the reduction in tmax (8-16%) and SNR(t) (52%) in the high-resolution experiment seems to be tolerable with this coil. In conclusion, parallel imaging is an alternative to reduce geometric distortions in fMRI at 1.5 T. Using a 32-channel coil, reduction of the voxel size might be the preferable way to improve spatial accuracy.

Far field and wavefront characterization of a high-power semiconductor laser for free space optical communications

NASA Technical Reports Server (NTRS)

Cornwell, Donald M., Jr.; Saif, Babak N.

1991-01-01

The spatial pointing angle and far field beamwidth of a high-power semiconductor laser are characterized as a function of CW power and also as a function of temperature. The time-averaged spatial pointing angle and spatial lobe width were measured under intensity-modulated conditions. The measured pointing deviations are determined to be well within the pointing requirements of the NASA Laser Communications Transceiver (LCT) program. A computer-controlled Mach-Zehnder phase-shifter interferometer is used to characterize the wavefront quality of the laser. The rms phase error over the entire pupil was measured as a function of CW output power. Time-averaged measurements of the wavefront quality are also made under intensity-modulated conditions. The measured rms phase errors are determined to be well within the wavefront quality requirements of the LCT program.

Moving Ahead With Eye Power

NASA Technical Reports Server (NTRS)

2002-01-01

NASA's Jet Propulsion Laboratory's collaborated with LC Technologies, Inc., to improve LCT's Eyegaze Communication System, an eye tracker that enables people with severe cerebral palsy, muscular dystrophy, multiple sclerosis, strokes, brain injuries, spinal cord injuries, and ALS (amyotrophic lateral sclerosis) to communicate and control their environment using their eye movements. To operate the system, the user sits in front of the computer monitor while the camera focuses on one eye. By looking at control keys on the monitor for a fraction of a second, the user can 'talk' with speech synthesis, type, operate a telephone, access the Internet and e-mail, and run computer software. Nothing is attached to the user's head or body, and the improved size and portability allow the system to be mounted on a wheelchair. LCT and JPL are working on several other areas of improvement that have commercial add-on potential.

Use of Lantibiotic Synthetases for the Preparation of Bioactive Constrained Peptides

PubMed Central

Levengood, Matthew R.

2008-01-01

Stabilization of biologically active peptides is a major goal in peptide-based drug design. Cyclization is an often-used strategy to enhance resistance of peptides towards protease degradation and simultaneously improve their affinity for targets by restricting their conformational flexibility. Amongst the various cyclization strategies, the use of thioether crosslinks has been successful for various peptides including enkephalin. The synthesis of these thioethers can be arduous, especially for longer peptides. Described herein is an enzymatic strategy taking advantage of the lantibiotic synthetase LctM that dehydrates Ser and Thr residues to the corresponding dehydroalanine and dehydrobutyrine residues and catalyzes the Michael-type addition of Cys residues to form thioether crosslinks. The use of LctM to prepare thioether containing analogs of enkephalin, contryphan, and inhibitors of human tripeptidyl peptidase II and spider venom epimerase is demonstrated. PMID:18294843

Medium-chain triglycerides impair lipid metabolism and induce hepatic steatosis in very long-chain acyl-CoA dehydrogenase (VLCAD)-deficient mice.

PubMed

Tucci, Sara; Primassin, Sonja; Ter Veld, Frank; Spiekerkoetter, Ute

2010-09-01

A medium-chain-triglyceride (MCT)-based diet is mainstay of treatment in very-long-chain acyl-CoA dehydrogenase deficiency (VLCADD), a long-chain fatty acid beta-oxidation defect. Beneficial effects have been reported with an MCT-bolus prior to exercise. Little is known about the impact of a long-term MCT diet on hepatic lipid metabolism. Here we investigate the effects of MCT-supplementation on liver and blood lipids in the murine model of VLCADD. Wild-type (WT) and VLCAD-knock-out (KO) mice were fed (1) a long-chain triglyceride (LCT)-diet over 5weeks, (2) an MCT diet over 5 weeks and (3) an LCT diet plus MCT-bolus. Blood and liver lipid content were determined. Expression of genes regulating lipogenesis was analyzed by RT-PCR. Under the LCT diet, VLCAD-KO mice accumulated significantly higher blood cholesterol concentrations compared to WT mice. The MCT-diet induced severe hepatic steatosis, significantly higher serum free fatty acids and impaired hepatic lipid mobilization in VLCAD-KO mice. Expression at mRNA level of hepatic lipogenic genes was up-regulated. The long-term MCT diet stimulates lipogenesis and impairs hepatic lipid metabolism in VLCAD-KO mice. These results suggest a critical reconsideration of a long-term MCT-modified diet in human VLCADD. In contrast, MCT in situations of increased energy demand appears to be a safer treatment alternative.

The Frequency of the LCT*-13910C>T Polymorphism Associated with Lactase Persistence Diverges among Euro-Descendant Groups from Brazil.

PubMed

Boschmann, Stefanie Epp; Boldt, Angelica Beate; de Souza, Ilíada Rainha; Petzl-Erler, Maria Luiza; Messias-Reason, Iara Jose

2016-01-01

The aim of this study was to investigate the frequency of the LCT*-13910C>T polymorphism associated with a high expression of lactase in the small intestine during adulthood, and to infer the lactase persistence and adult-type hypolactasia phenotypes among Euro-Brazilians and Mennonites from South Brazil. A sequence-specific PCR method to genotype the LCT*-13910C>T polymorphism in 292 Euro-Brazilians and 151 Mennonites (a group with European ancestry and a long history of endogamy) was developed. Using an exact test of population differentiation, the genotype and allele frequency between these and other Brazilian populations were compared. The frequency of -13910*T was significantly higher among the Mennonites when compared to the Euro-Brazilian cohort (0.63 vs. 0.33, p < 0.000001). Accordingly, Mennonites had a higher prevalence of the lactase persistence genotype (88.1 vs. 55.5%, p < 0.000001). The distribution of -13910*T differed between Mennonites and all other Brazilian groups (p < 0.0001). The Euro-Brazilians from Curitiba displayed differences when compared to all other Brazilian groups (p < 0.0001), even to Euro-Brazilians from a different geographic region (p = 0.0003), but were similar to those from Porto Alegre (p = 0.2). Differences in the -13910*T-associated lactase persistence distribution among Euro-Brazilian groups reflect the ancestry and admixture of each particular group and should be considered for adult-type hypolactasia screening. © 2015 S. Karger AG, Basel.

Dynamic Multi-Coil Shimming of the Human Brain at 7 Tesla

PubMed Central

Juchem, Christoph; Nixon, Terence W.; McIntyre, Scott; Boer, Vincent O.; Rothman, Douglas L.; de Graaf, Robin A.

2011-01-01

High quality magnetic field homogenization of the human brain (i.e. shimming) for MR imaging and spectroscopy is a demanding task. The susceptibility differences between air and tissue are a longstanding problem as they induce complex field distortions in the prefrontal cortex and the temporal lobes. To date, the theoretical gains of high field MR have only been realized partially in the human brain due to limited magnetic field homogeneity. A novel shimming technique for the human brain is presented that is based on the combination of non-orthogonal basis fields from 48 individual, circular coils. Custom-built amplifier electronics enabled the dynamic application of the multi-coil shim fields in a slice-specific fashion. Dynamic multi-coil (DMC) shimming is shown to eliminate most of the magnetic field inhomogeneity apparent in the human brain at 7 Tesla and provided improved performance compared to state-of-the-art dynamic shim updating with zero through third order spherical harmonic functions. The novel technique paves the way for high field MR applications of the human brain for which excellent magnetic field homogeneity is a prerequisite. PMID:21824794

PspF-binding domain PspA1-144 and the PspA·F complex: New insights into the coiled-coil-dependent regulation of AAA+ proteins.

PubMed

Osadnik, Hendrik; Schöpfel, Michael; Heidrich, Eyleen; Mehner, Denise; Lilie, Hauke; Parthier, Christoph; Risselada, H Jelger; Grubmüller, Helmut; Stubbs, Milton T; Brüser, Thomas

2015-11-01

Phage shock protein A (PspA) belongs to the highy conserved PspA/IM30 family and is a key component of the stress inducible Psp system in Escherichia coli. One of its central roles is the regulatory interaction with the transcriptional activator of this system, the σ(54) enhancer-binding protein PspF, a member of the AAA+ protein family. The PspA/F regulatory system has been intensively studied and serves as a paradigm for AAA+ enzyme regulation by trans-acting factors. However, the molecular mechanism of how exactly PspA controls the activity of PspF and hence σ(54) -dependent expression of the psp genes is still unclear. To approach this question, we identified the minimal PspF-interacting domain of PspA, solved its structure, determined its affinity to PspF and the dissociation kinetics, identified residues that are potentially important for PspF regulation and analyzed effects of their mutation on PspF in vivo and in vitro. Our data indicate that several characteristics of AAA+ regulation in the PspA·F complex resemble those of the AAA+ unfoldase ClpB, with both proteins being regulated by a structurally highly conserved coiled-coil domain. The convergent evolution of both regulatory domains points to a general mechanism to control AAA+ activity for divergent physiologic tasks via coiled-coil domains. © 2015 John Wiley & Sons Ltd.

Reconstruction of Horizontal Plasma Motions at the Photosphere from Intensitygrams: A Comparison Between DeepVel, LCT, FLCT, and CST

NASA Astrophysics Data System (ADS)

Tremblay, Benoit; Roudier, Thierry; Rieutord, Michel; Vincent, Alain

2018-04-01

Direct measurements of plasma motions in the photosphere are limited to the line-of-sight component of the velocity. Several algorithms have therefore been developed to reconstruct the transverse components from observed continuum images or magnetograms. We compare the space and time averages of horizontal velocity fields in the photosphere inferred from pairs of consecutive intensitygrams by the LCT, FLCT, and CST methods and the DeepVel neural network in order to identify the method that is best suited for generating synthetic observations to be used for data assimilation. The Stein and Nordlund ( Astrophys. J. Lett. 753, L13, 2012) magnetoconvection simulation is used to generate synthetic SDO/HMI intensitygrams and reference flows to train DeepVel. Inferred velocity fields show that DeepVel performs best at subgranular and granular scales and is second only to FLCT at mesogranular and supergranular scales.

Postpartum unconscious dynamics emerging from the Lüscher color test in Ethiopian women.

PubMed

Zanardo, Vincenzo; Gabrieli, Catia; Volpe, Francesca; Savio, Francesca; Straface, Gianluca; Soldera, Gino

2017-06-01

The aim of this study was to explore the feasibility of the Lüscher color test (LCT), a psychological instrument based on theory that colors are selected in unconscious way and that the color sensory perception of color is objective and universal. The research has involved 24 Ethiopian women, which delivered at the Getche Health Center in Gurage. It seemed to be relevant for the majority of Ethiopian women identify the rejected color (58.66%), the gray, than the favorite color, the yellow 33.33%). The yellow color suggests that they better express their personality in a physical context, while the gray color indicates that they want to live this experience intensely. This exploratory work lays the foundations for further studies in disadvantaged women, both in developing low-income Countries as well as in industrialized Countries characterized by an high level of emigration, and for clinical applications by the complete LCT version.

Rapid formation of cholesterol crystals in gallbladder bile is associated with stone recurrence after laparoscopic cholecystotomy.

PubMed

Jüngst, D; del Pozo, R; Dolu, M H; Schneeweiss, S G; Frimberger, E

1997-03-01

Laparoscopic cholecystotomy (LCT) with subsequent extraction of gallstones and primary closure of the gallbladder has been introduced as an alternative therapy for patients with cholecystolithiasis and preserved gallbladder function. However, stone recurrence has to be considered as a major drawback that might be related to lithogenic factors of gallbladder bile or the composition of gallbladder stones. Therefore, these were studied in relation to stone recurrence within an observation period of 1 to 5 years (median, 3.6 years) in 50 patients after LCT. The concentrations of total and individual bile acids, phospholipids, cholesterol, total lipids, mucin, protein, and the cholesterol saturation indices in gallbladder bile were not significantly different between 10 patients with and 40 patients without stone recurrence. However, the crystal observation time was significantly (P < .02) shorter (range, 1-2 days; median, 1.5) in the bile of patients with stone recurrence compared to those without (range, 1-21 days, median 3.5). Moreover, all 10 stone recurrences were observed in the 28 patients with a crystal observation time in the bile of less than or equal to 2 days (approximate annual risk: 12%-15%), and no recurrences were observed in the 22 patients with a crystal observation time greater than 2 days (P < .0001) or in patients with pigment stones. The rapid formation of cholesterol monohydrate crystals in bile seems to be the major risk factor for recurrent stones after LCT. These are most likely cholesterol stones and, therefore, are amenable to oral bile-acid prevention or treatment.

GPS Metric Tracking Unit

NASA Technical Reports Server (NTRS)

2008-01-01

As Global Positioning Satellite (GPS) applications become more prevalent for land- and air-based vehicles, GPS applications for space vehicles will also increase. The Applied Technology Directorate of Kennedy Space Center (KSC) has developed a lightweight, low-cost GPS Metric Tracking Unit (GMTU), the first of two steps in developing a lightweight, low-cost Space-Based Tracking and Command Subsystem (STACS) designed to meet Range Safety's link margin and latency requirements for vehicle command and telemetry data. The goals of STACS are to improve Range Safety operations and expand tracking capabilities for space vehicles. STACS will track the vehicle, receive commands, and send telemetry data through the space-based asset, which will dramatically reduce dependence on ground-based assets. The other step was the Low-Cost Tracking and Data Relay Satellite System (TDRSS) Transceiver (LCT2), developed by the Wallops Flight Facility (WFF), which allows the vehicle to communicate with a geosynchronous relay satellite. Although the GMTU and LCT2 were independently implemented and tested, the design collaboration of KSC and WFF engineers allowed GMTU and LCT2 to be integrated into one enclosure, leading to the final STACS. In operation, GMTU needs only a radio frequency (RF) input from a GPS antenna and outputs position and velocity data to the vehicle through a serial or pulse code modulation (PCM) interface. GMTU includes one commercial GPS receiver board and a custom board, the Command and Telemetry Processor (CTP) developed by KSC. The CTP design is based on a field-programmable gate array (FPGA) with embedded processors to support GPS functions.

Learner-centred teaching in a non-learner-centred world: An interpretive phenomenological study of the lived experience of clinical nursing faculty.

PubMed

Oyelana, Olabisi; Martin, Donna; Scanlan, Judith; Temple, Beverley

2018-08-01

With the growing complexities in the contemporary health care system, there is a challenge of preparing nurses for the practice demands. To this end, learner-centred teaching has emerged in many nursing curricula in Canada and evidence indicates its effectiveness in developing the essential practice skills in nursing students. It is important to examine the experience of the clinical faculty members who implement learner-centred teaching, as doing so would provide an insight to the factors that may hinder the implementation of learner-centred teaching in the practice settings. This phenomenological study aimed to address two research questions: what does learner-centred teaching mean to clinical nurse faculty? What is the lived experience of clinical nursing faculty who incorporate learner-centred teaching? Ten clinical nurse faculty members who had at least two years of clinical teaching experience volunteered to participate in the study. Data were collected using a semi-structured interview guide and audio recorder. Additional data sources included a demographic survey and a reflective journal. Multiple sub-themes emerged from this study from which three significant themes were consolidated: diversity of meanings, facilitators of LCT, and barriers to LCT. However, an overarching theme of "learner-centred teaching in a non-learner-centred world" was coined from participants' accounts of their experiences of barriers in incorporating LCT in the practice settings. A collaborative effort between faculty and the stakeholders is paramount to a successful implementation of learner-centred teaching in practice settings. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Solubilisation of poorly water-soluble drugs during in vitro lipolysis of medium- and long-chain triacylglycerols.

PubMed

Christensen, Janne Ørskov; Schultz, Kirsten; Mollgaard, Birgitte; Kristensen, Henning Gjelstrup; Mullertz, Anette

2004-11-01

The partitioning of poorly soluble drugs into an aqueous micellar phase was exploited using an in vitro lipid digestion model, simulating the events taking place during digestion of acylglycerols in the duodenum. The aqueous micellar phase was isolated after ultracentrifugation of samples obtained at different degrees of triacylglycerol hydrolysis. Flupentixol, 1'-[4-[1-(4-fluorophenyl)-1-H-indol-3-yl]-1-butyl]spiro[iso-benzofuran-1(3H), 4' piperidine] (LU 28-179) and probucol were studied. The effect of the alkyl chain length of the triacylglycerol was studied using a medium-chain triacylglycerol (MCT) and a long-chain triacylglycerol (LCT), respectively. In general, an oil solution was used as the lipid source in the model. Samples were analysed in regard to micellar size, lipid composition and drug concentration. During lipolysis, the content of lipolytic products in the aqueous micellar phase increased. The micellar size (R(H) approximately 3 nm) only increased when long-chain lipolytic products were incorporated in the mixed micelles (R(H) approximately 7.8 nm). Flupentixol was quickly transferred to the mixed micelles due to high solubility in this phase (100% released). A tendency towards higher solubilisation of LU 28-179, when it was administered in the LCT (approximately 24% released) compared to when it was administered in the MCT (approximately 15% released) at 70% hydrolysis, and a lagphase was observed. There was no difference in the solubilisation of probucol using MCT or LCT ( approximately 20% released), respectively. Differences in the physicochemical properties of the drugs resulted in differences in their distribution between the phases arising during lipolysis.

Fats infused intraduodenally affect the postprandial secretion of the exocrine pancreas and the plasma concentration of cholecystokinin but not of peptide YY in growing pigs.

PubMed

Jakob, S; Mosenthin, R; Zabielski, R; Rippe, C; Winzell, M S; Gacsalyi, U; Laubitz, D; Grzesiuk, E; Pierzynowski, S G

2000-10-01

In pigs, the spontaneous secretion of the exocrine pancreas and the release of cholecystokinin (CCK) and peptide YY (PYY) after intraduodenal infusion of fully saturated synthetic fats differing in chain length was studied. Growing pigs (n = 6) were prepared with pancreatic duct catheters, duodenal T-cannulas and catheters placed in the jugular vein. The pigs were fed 2 g/100 g body twice daily. Beginning with the morning feeding, a medium-chain triglyceride (MCT: glycerol tricaprylate), a long-chain triglyceride (LCT: glycerol tristearate) or saline was infused at a rate of 0.1 g/100 g body. Pancreatic juice was collected, beginning 1 h preprandially until 3 h postprandially. Blood samples were obtained 15 min preprandially and 15, 45, 90 and 150 min postprandially. The infusion of MCT evoked a change in the trend of the curve for the volume of secretion of pancreatic juice, lipase and colipase concentrations and outputs. The trend of the curve did not change over time for CCK and PYY. Differences between the trends of the curves for the saline and MCT treatment were observed for volume of secretion, protein output, lipase content and output, trypsin and colipase output. Differences in the trends of the curves between MCT and LCT were obtained for the outputs of protein, lipase and colipase. Plasma CCK levels were lower as a result of the MCT treatment compared with the saline and LCT treatments. The results suggest an immediate, distinguished response of the porcine exocrine pancreas to fats differing in chain length.

Pharmacoeconomics of parenteral nutrition in surgical and critically ill patients receiving structured triglycerides in China.

PubMed

Wu, Guo Hao; Ehm, Alexandra; Bellone, Marco; Pradelli, Lorenzo

2017-01-01

A prior meta-analysis showed favorable metabolic effects of structured triglyceride (STG) lipid emulsions in surgical and critically ill patients compared with mixed medium-chain/long-chain triglycerides (MCT/LCT) emulsions. Limited data on clinical outcomes precluded pharmacoeconomic analysis. We performed an updated meta-analysis and developed a cost model to compare overall costs for STGs vs MCT/LCTs in Chinese hospitals. We searched Medline, Embase, Wanfang Data, the China Hospital Knowledge Database, and Google Scholar for clinical trials comparing STGs to mixed MCT/LCTs in surgical or critically ill adults published between October 10, 2013 and September 19, 2015. Newly identified studies were pooled with the prior studies and an updated meta-analysis was performed. A deterministic simulation model was used to compare the effects of STGs and mixed MCT/LCT's on Chinese hospital costs. The literature search identified six new trials, resulting in a total of 27 studies in the updated meta-analysis. Statistically significant differences favoring STGs were observed for cumulative nitrogen balance, pre- albumin and albumin concentrations, plasma triglycerides, and liver enzymes. STGs were also associated with a significant reduction in the length of hospital stay (mean difference, -1.45 days; 95% confidence interval, -2.48 to -0.43; p=0.005) versus mixed MCT/LCTs. Cost analysis demonstrated a net cost benefit of ¥675 compared with mixed MCT/LCTs. STGs are associated with improvements in metabolic function and reduced length of hospitalization in surgical and critically ill patients compared with mixed MCT/LCT emulsions. Cost analysis using data from Chinese hospitals showed a corresponding cost benefit.

Attenuation correction for flexible magnetic resonance coils in combined magnetic resonance/positron emission tomography imaging.

PubMed

Eldib, Mootaz; Bini, Jason; Calcagno, Claudia; Robson, Philip M; Mani, Venkatesh; Fayad, Zahi A

2014-02-01

Attenuation correction for magnetic resonance (MR) coils is a new challenge that came about with the development of combined MR and positron emission tomography (PET) imaging. This task is difficult because such coils are not directly visible on either PET or MR acquisitions with current combined scanners and are therefore not easily localized in the field of view. This issue becomes more evident when trying to localize flexible MR coils (eg, cardiac or body matrix coil) that change position and shape from patient to patient and from one imaging session to another. In this study, we proposed a novel method to localize and correct for the attenuation and scatter of a flexible MR cardiac coil, using MR fiducial markers placed on the surface of the coil to allow for accurate registration of a template computed tomography (CT)-based attenuation map. To quantify the attenuation properties of the cardiac coil, a uniform cylindrical water phantom injected with 18F-fluorodeoxyglucose (18F-FDG) was imaged on a sequential MR/PET system with and without the flexible cardiac coil. After establishing the need to correct for the attenuation of the coil, we tested the feasibility of several methods to register a precomputed attenuation map to correct for the attenuation. To accomplish this, MR and CT visible markers were placed on the surface of the cardiac flexible coil. Using only the markers as a driver for registration, the CT image was registered to the reference image through a combination of rigid and deformable registration. The accuracy of several methods was compared for the deformable registration, including B-spline, thin-plate spline, elastic body spline, and volume spline. Finally, we validated our novel approach both in phantom and patient studies. The findings from the phantom experiments indicated that the presence of the coil resulted in a 10% reduction in measured 18F-FDG activity when compared with the phantom-only scan. Local underestimation reached 22% in regions of interest close to the coil. Various registration methods were tested, and the volume spline was deemed to be the most accurate, as measured by the Dice similarity metric. The results of our phantom experiments showed that the bias in the 18F-FDG quantification introduced by the presence of the coil could be reduced by using our registration method. An overestimation of only 1.9% of the overall activity for the phantom scan with the coil attenuation map was measured when compared with the baseline phantom scan without coil. A local overestimation of less than 3% was observed in the ROI analysis when using the proposed method to correct for the attenuation of the flexible cardiac coil. Quantitative results from the patient study agreed well with the phantom findings. We presented and validated an accurate method to localize and register a CT-based attenuation map to correct for the attenuation and scatter of flexible MR coils. This method may be translated to clinical use to produce quantitatively accurate measurements with the use of flexible MR coils during MR/PET imaging.

Role of medium-chain triglycerides in the alcohol-mediated cytochrome P450 2E1 induction of mitochondria.

PubMed

Lieber, Charles S; Cao, Qi; DeCarli, Leonore M; Leo, Maria A; Mak, Ki M; Ponomarenko, Anatoly; Ren, Chaoling; Wang, Xiaolei

2007-10-01

Chronic alcohol consumption is known to induce cytochrome P450 2E1 (CYP2E1) leading to lipid peroxidation, mitochondrial dysfunction and hepatotoxicity. We showed that replacement of dietary long-chain triglycerides (LCT) by medium-chain triglycerides (MCT) could be protective. We now wondered whether the induction of mitochondrial CYP2E1 plays a role and whether liver injury could be avoided through mitochondrial intervention. Rats were fed 4 different isocaloric liquid diets. The control group received our standard dextrin-maltose diet with intake limited to the average consumption of the 3 alcohol groups fed ad libitum the alcohol containing Lieber-DeCarli liquid diet. The fat was either 32% of calories as LCT (alcohol), or 16% as LCT + 16% as MCT (alcohol-MCT 16%), or 32% as MCT only (alcohol-MCT 32%). After 21 days, compared to the controls, the alcohol and both alcohol-MCT groups had a significant increase in mitochondrial CYP2E1 (p < 0.05 for both). As shown before, the same was found for the microsomal CYP2E1. When MCT replaced all the fat, like in the alcohol-MCT 32% group, CYP2E1 was significantly reduced by 40% in mitochondria (p < 0.05) and 30% in microsomes (p < 0.01). In mitochondria, 4-hydroxynonenal (4-HNE), a parameter of oxidative stress, paralleled CYP2E1. Compared to controls, alcohol and alcohol-MCT 16% significantly raised mitochondrial 4-HNE (p < 0.001), whereas the alcohol-MCT 32% diet brought it down to control levels (p < 0.001). Mitochondrial reduced glutathione (GSH) was also significantly lowered by alcohol consumption (p < 0.05), and it increased to almost normal levels with alcohol-MCT 32% (p = 0.006). These changes in the mitochondria reflected the reduction observed in total liver in which alcohol-MCT 32% decreased the alcohol-induced steatosis with a diminution of triglycerides (p < 0.001) and of the pro-inflammatory cytokine tumor necrosis factor-alpha (p < 0.001). Mitochondria participate in the induction of CYP2E1 by alcohol and contribute to lipid peroxidation and GSH depletion. Thus, lipid composition of the diet is an important determinant for the beneficial effect of MCT, with a diet containing a mixture of LCT/MCT being ineffective.

Survival and behavioural responses of the predatory ladybird beetle, Eriopis connexa populations susceptible and resistant to a pyrethroid insecticide.

PubMed

Spíndola, A F; Silva-Torres, C S A; Rodrigues, A R S; Torres, J B

2013-08-01

The ladybird beetle, Eriopis connexa (Germar) (Coleoptera: Coccinellidae), is one of the commonest predators of aphids (Hemiptera: Aphididae) in the cotton agroecosystem and in many other row and fruit crops in Brazil, and has been introduced into other countries such as the USA for purposes of aphid control. In addition, the boll weevil, Anthonomus grandis Boheman (Coleoptera: Curculionidae) is the most serious cotton pest where it occurs, including Brazil. Controlling boll weevils and other pests such as cotton defoliators still tends to involve the intense application of insecticides to secure cotton production. The pyrethroid insecticide lambda-cyhalothrin (LCT) is commonly used, but this compound is not effective against aphids; hence, a desirable strategy would be to maintain E. connexa populations in cotton fields where LCT is applied. Using populations of E. connexa resistant (Res) and susceptible (Sus) to LCT, we compared behavioural responses on treated cotton plants and under confinement on partially and fully treated surfaces, and assessed the insects' survival on treated plants compared with that of the boll weevil. The E. connexa resistant population caged on treated plants with 15 and 75 g a.i. ha-1 exhibited ≫82% survival for both insecticide concentrations compared with ≪3% and ≪17% survival for susceptible E. connexa populations and boll weevils, respectively. The response of E. connexa Res and Sus populations when released, either on the soil or on the plant canopy, indicated avoidance towards treated plants, as measured by elapsed time to assess the plant. When compared with susceptible individuals, resistant ones took longer time to suffer insecticide knockdown, had a higher recovery rate after suffering knockdown, and spent more time in the plant canopy. Based on behavioural parameters evaluated in treated arenas, no ladybird beetles exhibited repellency. However, irritability was evident, with the susceptible population exhibiting greater irritability compared with the resistant population and a subgroup comprising resistant individuals that had recovered from knockdown. The outcomes for the E. connexa Res population indicate a promising strategy for its maintenance when using the insecticide LCT in integrated pest management schemes to control boll weevil or other non-target pest of ladybird beetles in cotton fields.

Spatial Relationships between Biomass Burning and Land Use / Land Cover Dynamics in Northern Sub-Saharan Africa

NASA Astrophysics Data System (ADS)

Ellison, L.; Ichoku, C. M.

2016-12-01

Biomass burning (BB) is an extensive and persistent phenomenon across the world, and is a result of either natural (via lightning strikes) or anthropogenic processes, depending on the location. In Northern Sub-Saharan Africa (NSSA), where access to affordable modern farming equipment is extremely limited, agricultural practices dominate and BB is completely anthropogenic for all practical purposes, resulting in NSSA consistently contributing 15-20% of the total global annual emission of particulate matter from fires, according to estimates from version 1.0 of the Fire Energetics and Emissions Research BB emissions inventory (FEERv1.0, http://feer.gsfc.nasa.gov/data/emissions/). The FEERv1.0 algorithm uses a land cover type (LCT) product at either 0.5° or 0.1° resolutions for the conversion of total particulate matter estimates to various other smoke constituents. Due to the fact that fires are closely associated with land cover types, it became apparent that a fire-prone land cover type product at those spatial resolutions were needed, resulting in the FEERv1 BB-LCT product (http://feer.gsfc.nasa.gov/data/landcover/). In version 2 of the product, it was found that 6% of all grid cells with partial or full land cover in the original 0.5° LCT product is reclassified when considering BB practices. In NSSA, we see that the differences fall mainly along the borders between major regions of different LCT. Roughly speaking, fires along the cropland/savanna and savanna/forest borders in NSSA are mostly from from savanna burning. An in-depth analysis of the spatial extent and variability of fires and land cover in NSSA reveals that within the last one-and-a-half decades, the maximum fire activity occurred in the 2006/07 fire season and has been decreasing ever since. Interestingly, despite this decrease in fire activity, we observe a continuing increase in land cover conversion to cropland over the same time period at a rate of 0.3%/yr, which is equal to ≈37,500 km2/yr, or about 9 million new farms each year (assuming a farm size of one acre.) Attempts to understand this relationship are ongoing, and will also be summarized.

A low-cost, mechanically simple apparatus for measuring eddy current-induced magnetic fields in MRI.

PubMed

Gilbert, Kyle M; Martyn Klassen, L; Menon, Ravi S

2013-10-01

The fidelity of gradient waveforms in MRI pulse sequences is essential to the acquisition of images and spectra with minimal distortion artefacts. Gradient waveforms can become nonideal when eddy currents are created in nearby conducting structures; however, the resultant magnetic fields can be characterised and compensated for by measuring the spatial and temporal field response following a gradient impulse. This can be accomplished using a grid of radiofrequency (RF) coils. The RF coils must adhere to strict performance requirements: they must achieve a high sensitivity and signal-to-noise ratio (SNR), have minimal susceptibility field gradients between the sample and surrounding material interfaces and be highly decoupled from each other. In this study, an apparatus is presented that accomplishes these tasks with a low-cost, mechanically simple solution. The coil system consists of six transmit/receive RF coils immersed in a high-molarity saline solution. The sensitivity and SNR following an excitation pulse are sufficiently high to allow accurate phase measurements during free-induction decays; the intrinsic susceptibility matching of the materials, because of the unique design of the coil system, results in sufficiently narrow spectral line widths (mean of 19 Hz), and adjacent RF coils are highly decoupled (mean S12 of -47 dB). The temporal and spatial distributions of eddy currents following a gradient pulse are measured to validate the efficacy of the design, and the resultant amplitudes and time constants required for zeroth- and first-order compensation are provided. Copyright © 2013 John Wiley & Sons, Ltd.

WE-EF-207-01: FEATURED PRESENTATION and BEST IN PHYSICS (IMAGING): Task-Driven Imaging for Cone-Beam CT in Interventional Guidance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gang, G; Stayman, J; Ouadah, S

2015-06-15

Purpose: This work introduces a task-driven imaging framework that utilizes a patient-specific anatomical model, mathematical definition of the imaging task, and a model of the imaging system to prospectively design acquisition and reconstruction techniques that maximize task-based imaging performance. Utility of the framework is demonstrated in the joint optimization of tube current modulation and view-dependent reconstruction kernel in filtered-backprojection reconstruction and non-circular orbit design in model-based reconstruction. Methods: The system model is based on a cascaded systems analysis of cone-beam CT capable of predicting the spatially varying noise and resolution characteristics as a function of the anatomical model and amore » wide range of imaging parameters. Detectability index for a non-prewhitening observer model is used as the objective function in a task-driven optimization. The combination of tube current and reconstruction kernel modulation profiles were identified through an alternating optimization algorithm where tube current was updated analytically followed by a gradient-based optimization of reconstruction kernel. The non-circular orbit is first parameterized as a linear combination of bases functions and the coefficients were then optimized using an evolutionary algorithm. The task-driven strategy was compared with conventional acquisitions without modulation, using automatic exposure control, and in a circular orbit. Results: The task-driven strategy outperformed conventional techniques in all tasks investigated, improving the detectability of a spherical lesion detection task by an average of 50% in the interior of a pelvis phantom. The non-circular orbit design successfully mitigated photon starvation effects arising from a dense embolization coil in a head phantom, improving the conspicuity of an intracranial hemorrhage proximal to the coil. Conclusion: The task-driven imaging framework leverages a knowledge of the imaging task within a patient-specific anatomical model to optimize image acquisition and reconstruction techniques, thereby improving imaging performance beyond that achievable with conventional approaches. 2R01-CA-112163; R01-EB-017226; U01-EB-018758; Siemens Healthcare (Forcheim, Germany)« less

IMPROVED TEMPERATURE GRADIENT FOR MONITORING BEHAVIORAL THERMOREGULATION IN THE RAT

EPA Science Inventory

Past studies have found that the laboratory rat placed In a temperature gradient prefers temperatures that are markedly below its lower critical ambient temperature (LCT), whereas other rodents (e.g., mouse, hamster, and guinea pig) generally select thermal environments associate...

Detection of Mycobacterium bovis in Bovine and Bubaline Tissues Using Nested-PCR for TbD1

PubMed Central

Araújo, Cristina P.; Osório, Ana Luiza A. R.; Jorge, Kláudia S. G.; Ramos, Carlos Alberto N.; Filho, Antonio Francisco S.; Vidal, Carlos Eugênio S.; Roxo, Eliana; Nishibe, Christiane; Almeida, Nalvo F.; Júnior, Antônio A. F.; Silva, Marcio R.; Neto, José Diomedes B.; Cerqueira, Valíria D.; Zumárraga, Martín J.; Araújo, Flábio R.

2014-01-01

In the present study, a nested-PCR system, targeting the TbD1 region, involving the performance of conventional PCR followed by real-time PCR, was developed to detect Mycobacterium bovis in bovine/bubaline tissue homogenates. The sensitivity and specificity of the reactions were assessed with DNA samples extracted from tuberculous and non-tuberculous mycobacteria, as well as other actinomycetales species and DNA samples extracted directly from bovine and bubaline tissue homogenates. In terms of analytical sensitivity, the DNA of M. bovis AN5 was detected up to 1.56 ng with conventional PCR, 97.6 pg with real-time PCR, and 1.53 pg with nested-PCR in the reaction mixture. The nested-PCR exhibited 100% analytical specificity for M. bovis when tested with the DNA of reference strains of environmental mycobacteria and closely-related Actinomycetales. A clinical sensitivity value of 76.0% was detected with tissue samples from animals that exhibited positive results in the comparative intradermal tuberculin test (CITT), as well as from those with lesions compatible with tuberculosis (LCT) that rendered positive cultures. A clinical specificity value of 100% was detected with tissue samples from animals with CITT- results, with no visible lesions (NVL) and negative cultures. No significant differences were found between the nested-PCR and culture in terms of detecting CITT+ animals with LCT or with NVL. No significant differences were recorded in the detection of CITT- animals with NVL. However, nested-PCR detected a significantly higher number of positive animals than the culture in the group of animals exhibiting LCT with no previous records of CITT. The use of the nested-PCR assay to detect M. bovis in tissue homogenates provided a rapid diagnosis of bovine and bubaline tuberculosis. PMID:24618787

Detection of Mycobacterium bovis in bovine and bubaline tissues using nested-PCR for TbD1.

PubMed

Araújo, Cristina P; Osório, Ana Luiza A R; Jorge, Kláudia S G; Ramos, Carlos Alberto N; Filho, Antonio Francisco S; Vidal, Carlos Eugênio S; Roxo, Eliana; Nishibe, Christiane; Almeida, Nalvo F; Júnior, Antônio A F; Silva, Marcio R; Neto, José Diomedes B; Cerqueira, Valíria D; Zumárraga, Martín J; Araújo, Flábio R

2014-01-01

In the present study, a nested-PCR system, targeting the TbD1 region, involving the performance of conventional PCR followed by real-time PCR, was developed to detect Mycobacterium bovis in bovine/bubaline tissue homogenates. The sensitivity and specificity of the reactions were assessed with DNA samples extracted from tuberculous and non-tuberculous mycobacteria, as well as other actinomycetales species and DNA samples extracted directly from bovine and bubaline tissue homogenates. In terms of analytical sensitivity, the DNA of M. bovis AN5 was detected up to 1.56 ng with conventional PCR, 97.6 pg with real-time PCR, and 1.53 pg with nested-PCR in the reaction mixture. The nested-PCR exhibited 100% analytical specificity for M. bovis when tested with the DNA of reference strains of environmental mycobacteria and closely-related Actinomycetales. A clinical sensitivity value of 76.0% was detected with tissue samples from animals that exhibited positive results in the comparative intradermal tuberculin test (CITT), as well as from those with lesions compatible with tuberculosis (LCT) that rendered positive cultures. A clinical specificity value of 100% was detected with tissue samples from animals with CITT- results, with no visible lesions (NVL) and negative cultures. No significant differences were found between the nested-PCR and culture in terms of detecting CITT+ animals with LCT or with NVL. No significant differences were recorded in the detection of CITT- animals with NVL. However, nested-PCR detected a significantly higher number of positive animals than the culture in the group of animals exhibiting LCT with no previous records of CITT. The use of the nested-PCR assay to detect M. bovis in tissue homogenates provided a rapid diagnosis of bovine and bubaline tuberculosis.

Separation and aquatic toxicity of enantiomers of the pyrethroid insecticide lambda-cyhalothrin.

PubMed

Xu, Chao; Wang, Jiajia; Liu, Weiping; Daniel Sheng, G; Tu, Yunjie; Ma, Yun

2008-01-01

Chiral pollutants are receiving growing environmental concern due to differential biological activities of their enantiomers. In the present study, enantiomeric separation of the pyrethroid insecticide lambda-cyhalothrin (LCT) was investigated by high-performance liquid chromatography (HPLC) using the columns of Chiralpak AD (amylase tris[3,5-dimethyl-phenyl carbamate]), Chiralpak AS (amylase tris[(S)-1-phenyl carbamate]), Chiralcel OD (cellulose tris[3,5-dimethylphenyl carbamate]), and Chiralcel OJ (cellulose tris[4-methyl benzoate]) with different chiral stationary phases. The differential toxicities of the enantiomers in aquatic systems were evaluated using the acute zebrafish (Danio rerio) toxicity test and the zebrafish embryo test. The enantiomers of LCT were separated completely on all the columns tested and detected by circular dichroism at 236 nm. Better separations were achieved at lower temperatures (e.g., 20 degrees C) and lower levels of polar modifiers (162 times more toxic than its antipode to zebrafish in the acute test. The embryo test indicated that the exposure to LCT enantioselectively induced crooked body, yolk sac edema, and pericardial edema and that the (-)-enantiomer was 7.2 times stronger than the (+)-enantiomer in 96-h mortality. The malformations were induced by the racemate and its (-)-enantiomer at lower concentrations tested (e.g., 50 microg L(-1)), whereas the (+)-enantiomer induced malformations at relatively higher concentrations (>/=100 microg L(-1)). These results suggest that the toxicological effects of chiral pesticides must be evaluated using their individual enantiomers.

Fatty acid chain length, postprandial satiety and food intake in lean men.

PubMed

Poppitt, S D; Strik, C M; MacGibbon, A K H; McArdle, B H; Budgett, S C; McGill, A-T

2010-08-04

High-fat diets are associated with obesity, and the weak satiety response elicited in response to dietary lipids is likely to play a role. Preliminary evidence from studies of medium (MCT) and long chain triglycerides (LCT) supports greater appetite suppression on high-MCT diets, possibly a consequence of direct portal access, more rapid oxidation and muted lipaemia. No data is as yet available on high-SCT diets which also have direct hepatic access. In this study SCT- (dairy fats), MCT- (coconut oil) and LCT-enriched (beef tallow) test breakfasts (3.3 MJ) containing 52 g lipid (58 en% fat) were investigated in a randomized, cross-over study in 18 lean men. All participants were required to complete the 3 study days in randomised order. Participants rated appetite sensations using visual analogue scales (VAS), and energy intake (EI) was measured by covert weighing of an ad libitum lunch meal 3.5 h postprandially. Blood samples were collected by venous cannulation. There were no detectable differences between breakfasts in perceived pleasantness, visual appearance, smell, taste, aftertaste and palatability (P>0.05). There was no significant effect of fatty acid chain length on ratings of hunger, fullness, satisfaction or current thoughts of food, nor did energy (mean, sem: SCT: 4406, 366 kJ; MCT: 4422, 306 kJ; LCT: 4490, 324 kJ; P>0.05) or macronutrient intake at lunch differ between diets. The maximum difference in EI between diets was less than 2%. Postprandial lipaemia also did not differ significantly. We conclude that there was no evidence that fatty acid chain length has an effect on measures of appetite and food intake when assessed following a single high-fat test meal in lean participants. Copyright 2010 Elsevier Inc. All rights reserved.

Rapid cellular enrichment of eicosapentaenoate after a single intravenous injection of a novel medium-chain triacylglycerol:fish-oil emulsion in humans123

PubMed Central

Carpentier, Yvon A; Hacquebard, Mirjam; Portois, Laurence; Dupont, Isabelle E; Deckelbaum, Richard J

2010-01-01

Background: Dietary deficiency in n−3 (omega-3) polyunsaturated fatty acids (PUFAs) prevails in Western populations and potentially results in adverse health outcomes. To circumvent the slow n−3 PUFA incorporation in phospholipids of key cells after oral supplementation, a new preparation for intravenous bolus injection was developed with 20 g triacylglycerols/100 mL of a mixture of 80% medium-chain triacylglycerols (MCTs) and 20% fish oil (FO) (wt:wt), and 0.4 g α-tocopherol/100 mL of the same mixture. Objective: Our objective was to document the enrichment of n−3 PUFAs in leukocyte and platelet phospholipids after a bolus intravenous injection of MCT:FO in men. Design: Twelve healthy male subjects received injections over a 5-min period of 50 mL of either MCT:FO or a control MCT:long-chain triacylglycerol (MCT:LCT) emulsion containing 20 g triacylglycerols/100 mL with equal amounts (wt:wt) of MCT and soybean triacylglycerols (LCT) and containing 0.02 g α-tocopherol/100 mL; after an 8-wk interval, the subjects received injections of the other preparation. Results: Clinical and biological variables that assessed tolerance and safety remained unchanged. Plasma elimination was faster for MCT:FO than for MCT:LCT (half-life: 24.5 ± 3.5 min compared with 32.9 ± 3.0 min; P < 0.025). This was associated with a greater increase in the plasma nonesterified fatty acid concentration. The content of n−3 PUFAs, specifically eicosapentaenoic acid (20:5n−3), increased in leukocyte and platelet phospholipids within 60 min and ≥24 h after MCT:FO injection. Conclusion: Bolus intravenous injection of a novel MCT:FO emulsion allows rapid enrichment of cells with n−3 PUFAs. PMID:20147473

Magnetic Footpoint Velocities: A Combination Of Minimum Energy Fit AndLocal Correlation Tracking

NASA Astrophysics Data System (ADS)

Belur, Ravindra; Longcope, D.

2006-06-01

Many numerical and time dependent MHD simulations of the solar atmosphererequire the underlying velocity fields which should be consistent with theinduction equation. Recently, Longcope (2004) introduced a new techniqueto infer the photospheric velocity field from sequence of vector magnetogramswhich are in agreement with the induction equation. The method, the Minimum Energy Fit (MEF), determines a set of velocities and selects the velocity which is smallest overall flow speed by minimizing an energy functional. The inferred velocity can be further constrained by information aboutthe velocity inferred from other techniques. With this adopted techniquewe would expect that the inferred velocity will be close to the photospheric velocity of magnetic footpoints. Here, we demonstrate that the inferred horizontal velocities from LCT can be used to constrain the MEFvelocities. We also apply this technique to actual vector magnetogramsequences and compare these velocities with velocities from LCT alone.This work is supported by DoD MURI and NSF SHINE programs.

Spectral Elements Analysis for Viscoelastic Fluids at High Weissenberg Number Using Logarithmic conformation Tensor Model

NASA Astrophysics Data System (ADS)

Jafari, Azadeh; Deville, Michel O.; Fiétier, Nicolas

2008-09-01

This study discusses the capability of the constitutive laws for the matrix logarithm of the conformation tensor (LCT model) within the framework of the spectral elements method. The high Weissenberg number problems (HWNP) usually produce a lack of convergence of the numerical algorithms. Even though the question whether the HWNP is a purely numerical problem or rather a breakdown of the constitutive law of the model has remained somewhat of a mystery, it has been recognized that the selection of an appropriate constitutive equation constitutes a very crucial step although implementing a suitable numerical technique is still important for successful discrete modeling of non-Newtonian flows. The LCT model formulation of the viscoelastic equations originally suggested by Fattal and Kupferman is applied for 2-dimensional (2D) FENE-CR model. The Planar Poiseuille flow is considered as a benchmark problem to test this representation at high Weissenberg number. The numerical results are compared with numerical solution of the standard constitutive equation.

Functional magnetic resonance imaging and transcranial magnetic stimulation: effects of motor imagery, movement and coil orientation.

PubMed

Niyazov, D M; Butler, A J; Kadah, Y M; Epstein, C M; Hu, X P

2005-07-01

To compare fMRI activations during movement and motor imagery to corresponding motor evoked potential (MEP) maps obtained with the TMS coil in three different orientations. fMRI activations during executed (EM) and imagined (IM) movements of the index finger were compared to MEP maps of the first dorsal interosseus (FDI) muscle obtained with the TMS coil in anterior, posterior and lateral handle positions. To ensure spatial registration of fMRI and MEP maps, a special grid was used in both experiments. No statistically significant difference was found between the TMS centers of gravity (TMS CoG) obtained with the three coil orientations. There was a significant difference between fMRI centers of gravity during IMs (IM CoG) and EMs (EM CoG), with IM CoGs localized on average 10.3mm anterior to those of EMs in the precentral gyrus. Most importantly, the IM CoGs closely matched cortical projections of the TMS CoGs while the EM CoGs were on average 9.5mm posterior to the projected TMS CoGs. TMS motor maps are more congruent with fMRI activations during motor imagery than those during EMs. These findings are not significantly affected by changing orientation of the TMS coil. Our results suggest that the discrepancy between fMRI and TMS motor maps may be largely due to involvement of the somatosensory component in the EM task.

Magnetic Resonance Imaging of Phosphocreatine and Determination of BOLD Kinetics in Lower Extremity Muscles using a Dual-Frequency Coil Array

NASA Astrophysics Data System (ADS)

Brown, Ryan; Khegai, Oleksandr; Parasoglou, Prodromos

2016-07-01

Magnetic resonance imaging (MRI) provides the unique ability to study metabolic and microvasculature functions in skeletal muscle using phosphorus and proton measurements. However, the low sensitivity of these techniques can make it difficult to capture dynamic muscle activity due to the temporal resolution required for kinetic measurements during and after exercise tasks. Here, we report the design of a dual-nuclei coil array that enables proton and phosphorus MRI of the human lower extremities with high spatial and temporal resolution. We developed an array with whole-volume coverage of the calf and a phosphorus signal-to-noise ratio of more than double that of a birdcage coil in the gastrocnemius muscles. This enabled the local assessment of phosphocreatine recovery kinetics following a plantar flexion exercise using an efficient sampling scheme with a 6 s temporal resolution. The integrated proton array demonstrated image quality approximately equal to that of a clinical state-of-the-art knee coil, which enabled fat quantification and dynamic blood oxygen level-dependent measurements that reflect microvasculature function. The developed array and time-efficient pulse sequences were combined to create a localized assessment of calf metabolism using phosphorus measurements and vasculature function using proton measurements, which could provide new insights into muscle function.

Theorising Knowledge Practices: A Missing Piece of the Educational Technology Puzzle

ERIC Educational Resources Information Center

Howard, Sarah; Maton, Karl

2011-01-01

Educational technology research has been characterised as lacking theoretical frameworks that can enable cumulative knowledge-building across the field. This article explores the value of Legitimation Code Theory (LCT) for addressing these issues by discussing research into the key of integration of information and communication technologies in…

The power spectrum of solar convection flows from high-resolution observations and 3D simulations

NASA Astrophysics Data System (ADS)

Yelles Chaouche, L.; Moreno-Insertis, F.; Bonet, J. A.

2014-03-01

Context. Understanding solar surface magnetoconvection requires the study of the Fourier spectra of the velocity fields. Nowadays, observations are available that resolve very small spatial scales, well into the subgranular range, almost reaching the scales routinely resolved in numerical magnetoconvection simulations. Comparison of numerical and observational data at present can provide an assessment of the validity of the observational proxies. Aims: Our aims are: (1) to obtain Fourier spectra for the photospheric velocity fields using the spectropolarimetric observations with the highest spatial resolution so far (~120 km), thus reaching for the first time spatial scales well into the subgranular range; (2) to calculate corresponding Fourier spectra from realistic 3D numerical simulations of magnetoconvection and carry out a proper comparison with their observational counterparts considering the residual instrumental degradation in the observational data; and (3) to test the observational proxies on the basis of the numerical data alone, by comparing the actual velocity field in the simulations with synthetic observations obtained from the numerical boxes. Methods: (a) For the observations, data from the SUNRISE/IMaX spectropolarimeter are used. (b) For the simulations, we use four series of runs obtained with the STAGGER code for different average signed vertical magnetic field values (0, 50, 100, and 200 G). Spectral line profiles are synthesized from the numerical boxes for the same line observed by IMaX (Fe I 5250.2 Å) and degraded to match the performance of the IMaX instrument. Proxies for the velocity field are obtained via Dopplergrams (vertical component) and local correlation tracking (LCT, for the horizontal component). Fourier power spectra are calculated and a comparison between the synthetic and observational data sets carried out. (c) For the internal comparison of the numerical data, velocity values on constant optical depth surfaces are used instead of on horizontal planes. Results: A very good match between observational and simulated Fourier power spectra is obtained for the vertical velocity data for scales between 200 km and 6 Mm. Instead, a clear vertical shift is obtained when the synthetic observations are not degraded to emulate the degradation in the IMaX data. The match for the horizontal velocity data is much less impressive because of the inaccuracies of the LCT procedure. Concerning the internal comparison of the direct velocity values of the numerical boxes with those from the synthetic observations, a high correlation (0.96) is obtained for the vertical component when using the velocity values on the log τ500 = -1 surface in the box. The corresponding Fourier spectra are near each other. A lower maximum correlation (0.5) is reached (at log τ500 = 0) for the horizontal velocities as a result of the coarseness of the LCT procedure. Correspondingly, the Fourier spectra for the LCT-determined velocities is well below that from the actual velocity components. Conclusions: As measured by the Fourier spectra, realistic numerical simulations of surface magnetoconvection provide a very good match to the observational proxies for the photospheric velocity fields at least on scales from several Mm down to around 200 km. Taking into account the spatial and spectral instrumental blurring is essential for the comparison between simulations and observations. Dopplergrams are an excellent proxy for the vertical velocities on constant-τ isosurfaces, while LCT is a much less reliable method of determining the horizontal velocities.

Counter-streaming flows in a giant quiet-Sun filament observed in the extreme ultraviolet

NASA Astrophysics Data System (ADS)

Diercke, A.; Kuckein, C.; Verma, M.; Denker, C.

2018-03-01

Aim. The giant solar filament was visible on the solar surface from 2011 November 8-23. Multiwavelength data from the Solar Dynamics Observatory (SDO) were used to examine counter-streaming flows within the spine of the filament. Methods: We use data from two SDO instruments, the Atmospheric Imaging Assembly (AIA) and the Helioseismic and Magnetic Imager (HMI), covering the whole filament, which stretched over more than half a solar diameter. Hα images from the Kanzelhöhe Solar Observatory (KSO) provide context information of where the spine of the filament is defined and the barbs are located. We apply local correlation tracking (LCT) to a two-hour time series on 2011 November 16 of the AIA images to derive horizontal flow velocities of the filament. To enhance the contrast of the AIA images, noise adaptive fuzzy equalization (NAFE) is employed, which allows us to identify and quantify counter-streaming flows in the filament. We observe the same cool filament plasma in absorption in both Hα and EUV images. Hence, the counter-streaming flows are directly related to this filament material in the spine. In addition, we use directional flow maps to highlight the counter-streaming flows. Results: We detect counter-streaming flows in the filament, which are visible in the time-lapse movies in all four examined AIA wavelength bands (λ171 Å, λ193 Å, λ304 Å, and λ211 Å). In the time-lapse movies we see that these persistent flows lasted for at least two hours, although they became less prominent towards the end of the time series. Furthermore, by applying LCT to the images we clearly determine counter-streaming flows in time series of λ171 Å and λ193 Å images. In the λ304 Å wavelength band, we only see minor indications for counter-streaming flows with LCT, while in the λ211 Å wavelength band the counter-streaming flows are not detectable with this method. The diverse morphology of the filament in Hα and EUV images is caused by different absorption processes, i.e., spectral line absorption and absorption by hydrogen and helium continua, respectively. The horizontal flows reach mean flow speeds of about 0.5 km s-1 for all wavelength bands. The highest horizontal flow speeds are identified in the λ171 Å band with flow speeds of up to 2.5 km s-1. The results are averaged over a time series of 90 minutes. Because the LCT sampling window has finite width, a spatial degradation cannot be avoided leading to lower estimates of the flow velocities as compared to feature tracking or Doppler measurements. The counter-streaming flows cover about 15-20% of the whole area of the EUV filament channel and are located in the central part of the spine. Conclusions: Compared to the ground-based observations, the absence of seeing effects in AIA observations reveal counter-streaming flows in the filament even with a moderate image scale of 0. ''6 pixel-1. Using a contrast enhancement technique, these flows can be detected and quantified with LCT in different wavelengths. We confirm the omnipresence of counter-streaming flows also in giant quiet-Sun filaments. A movie associated to Fig. 6 is available at http://https://www.aanda.org

Tracking the eye non-invasively: simultaneous comparison of the scleral search coil and optical tracking techniques in the macaque monkey

PubMed Central

Kimmel, Daniel L.; Mammo, Dagem; Newsome, William T.

2012-01-01

From human perception to primate neurophysiology, monitoring eye position is critical to the study of vision, attention, oculomotor control, and behavior. Two principal techniques for the precise measurement of eye position—the long-standing sclera-embedded search coil and more recent optical tracking techniques—are in use in various laboratories, but no published study compares the performance of the two methods simultaneously in the same primates. Here we compare two popular systems—a sclera-embedded search coil from C-N-C Engineering and the EyeLink 1000 optical system from SR Research—by recording simultaneously from the same eye in the macaque monkey while the animal performed a simple oculomotor task. We found broad agreement between the two systems, particularly in positional accuracy during fixation, measurement of saccade amplitude, detection of fixational saccades, and sensitivity to subtle changes in eye position from trial to trial. Nonetheless, certain discrepancies persist, particularly elevated saccade peak velocities, post-saccadic ringing, influence of luminance change on reported position, and greater sample-to-sample variation in the optical system. Our study shows that optical performance now rivals that of the search coil, rendering optical systems appropriate for many if not most applications. This finding is consequential, especially for animal subjects, because the optical systems do not require invasive surgery for implantation and repair of search coils around the eye. Our data also allow laboratories using the optical system in human subjects to assess the strengths and limitations of the technique for their own applications. PMID:22912608

Habari Za Kiswahili: The History of Swahili Instruction at the K-12 Level in Madison, Wisconsin.

ERIC Educational Resources Information Center

Kuntz, Patricia S.

Since the enactment of the 1958 National Defense Education Act, funded universities have provided African language instruction at the postsecondary level. With an increased interest in the less commonly taught languages (LCT) demonstrated by the 1988 Foreign Language Assistance Act, several African Studies Center universities provide instruction…

Color Preference and MMPI Scores of Alcohol and Drug Addicts.

ERIC Educational Resources Information Center

Cernovsky, Zdenek

1986-01-01

Inpatients (n=67) treated for alcohol and drug abuse were administered the MMPI (Minnesota Multiphasic Personality Inventory) and Luescher Color Test (LCT). Patients showed more preference for brown than did normal adults and also obtained higher (i.e., presumably more pathological) scores on Luescher's total score scale and compensation scale.…

A New LC-MS-based Strategy to integrate chemistry, morphology, and evolution of eggplant (Solanum) species

USDA-ARS?s Scientific Manuscript database

The economically valuable giant genus Solanum, containing dozens of functional food species such as eggplant and tomato, affords an excellent system to compare and correlate metabolic chemistry with species morphology and evolution. Here, we devised a strategy based on repeatable reversed-phase LC-T...

Cytotoxicity of lambda-cyhalothrin on the macrophage cell line RAW 264.7.

PubMed

Zhang, Quan; Wang, Cui; Sun, Liwei; Li, Ling; Zhao, Meirong

2010-01-01

The wide use and wide-spectrum toxicity of synthetic pyrethroids (SPs) insecticides make them an emerging ecotoxicological concern. Some previous studies showed that SPs possessed cytotoxicity in some immune cells such as human lymphocytes and rat bone marrow. However, the cytotoxicity of SPs to macrophages, which are crucial to innate immunity, has not been explored. In the present report, we investigated a new pyrethroid insecticide, lambda-cyhalothrin (LCT), which may increase the generation of reactive oxygen species (ROS) and DNA damage levels and cause cytotoxicity in RAW 264.7 cells in dose- and time-dependent manners. The results for the first time implicated increased endogenous ROS and DNA damage as co-mediators of LCT-induced cytotoxicity in macrophages. Our results also suggested that macrophages were involved in synthetic pyrethroid-induced adverse immune effects. Considering the ubiquitous environmental presence of SPs, this study provided new information relative to the potential long-term physiological and immunological effects associated with chronic exposure to SPs. Hence, the potential immunotoxicity of SPs should be considered in assessing the safety of these compounds in sensitive environmental compartments.

Effect of chronic alcohol consumption on Hepatic SIRT1 and PGC-1{alpha} in rats

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lieber, Charles S.; Department of Medicine, Mount Sinai School of Medicine, New York, NY; Leo, Maria A.

2008-05-23

The nuclear genes, NAD-dependent deacetylase Sirtuis 1 (SIRT1) and the peroxisome proliferator-activated receptor-{gamma} coactivator1{alpha} (PGC-1{alpha}) are regulators of energy metabolism. Here, we studied the role of alcohol consumption in expression of these sensing molecules. Alcohol significantly reduced hepatic SIRT1 mRNA by 50% and PGC-1{alpha} mRNA by 46% and it significantly inhibited the protein expression of SIRT1 and PGC-1{alpha}, while the transcription factor PPAR-{gamma} remained unchanged. However, when the lipid composition of the alcohol diet was changed by replacing long-chain triglycerides (LCT) with medium chain triglycerides (MCT), SIRT1 and PGC-1{alpha} mRNA were restored to near control levels. This study demonstrates thatmore » alcohol reduces key energy sensing proteins and that replacement of LCT by MCT affects the transcription of these genes. Since there is a pathophysiological link between SIRT1 and PGC-1{alpha} and mitochondrial energy, the implication of the study is that mitochondrial dysfunction due to alcohol abuse can be treated by dietary modifications.« less

Compact, Low-Noise Magnetic Sensor with Fluxgate (DC) and Induction (AC) Modes of Operation

DTIC Science & Technology

2009-07-01

induction sensor and the fluxgate magnetometer . ......................................... 2 Figure 3.1 - Impulse response of a 4” long coil (#6...Block diagram of the Year 2, Task 2 fluxgate magnetometer . ................................... 6 Figure 3.3 - FIS-prototype magnetic-field...and demonstrated an innovative dual-mode, fluxgate -induction sensor (FIS) that combines a fluxgate magnetometer and an electromagnetic (EM) induction

Application of induction coil measurements to the study of superalloy hot corrosion and oxidation

NASA Technical Reports Server (NTRS)

Deadmore, D. L.

1984-01-01

The assessment of the degree of hot corrosion attack on nickel based alloys is a difficult task, especially when the definition specifies that it must be in terms of metal consumed and even more difficult if the measurement must be nondestructive. The inductance of a solenoid coil responds to changes in volume of fill and composition of metal cores, therefore, it may be used for nondestructive measurement of hot corrosion. The hot corrosion of U700 was studied at 900 C in a Mach 0.3 flame doped with 0.85 wppm of sodium. The change of inductance was found to define the known corrosion behavior and to suggest its use as a tool with predictive capabilities. Sufficient sensitivity exists to detect oxidation of this alloy at 900 C.

The safety of Lipistart, a medium-chain triglyceride based formula, in the dietary treatment of long-chain fatty acid disorders: a phase I study.

PubMed

MacDonald, Anita; Webster, Rachel; Whitlock, Matthew; Gerrard, Adam; Daly, Anne; Preece, Mary Anne; Evans, Sharon; Ashmore, Catherine; Chakrapani, Anupam; Vijay, Suresh; Santra, Saikat

2018-03-28

Children with long-chain fatty acid β-oxidation disorders (LCFAOD) presenting with clinical symptoms are treated with a specialist infant formula, with medium chain triglyceride (MCT) mainly replacing long chain triglyceride (LCT). It is essential that the safety and efficacy of any new specialist formula designed for LCFAOD be tested in infants and children. In an open-label, 21-day, phase I trial, we studied the safety of a new MCT-based formula (feed 1) in six well-controlled children (three male), aged 7-13 years (median 9 years) with LCFAOD (very long chain acyl CoA dehydrogenase deficiency [VLCADD], n=2; long chain 3-hydroxyacyl CoA dehydrogenase deficiency [LCHADD], n=2; carnitine acyl carnitine translocase deficiency [CACTD], n=2). Feed 1 (Lipistart; Vitaflo) contained 30% energy from MCT, 7.5% LCT and 3% linoleic acid and it was compared with a conventional MCT feed (Monogen; Nutricia) (feed 2) containing 17% energy from MCT, 3% LCT and 1.1% linoleic acid. Subjects consumed feed 2 for 7 days then feed 1 for 7 days and finally resumed feed 2 for 7 days. Vital signs, blood biochemistry, ECG, weight, height, food/feed intake and symptoms were monitored. Five subjects completed the study. Their median daily volume of both feeds was 720 mL (range 500-1900 mL/day). Feed 1 was associated with minimal changes in tolerance, free fatty acids (FFA), acylcarnitines, 3-hydroxybutyrate (3-HB), creatine kinase (CK), blood glucose, liver enzymes and no change in an electrocardiogram (ECG). No child complained of muscle pain or symptoms associated with LCFAOD on either feed. This is the first safety trial reported of an MCT formula specifically designed for infants and children with LCFAOD. In this short-term study, it appeared safe and well tolerated in this challenging group.

Impact of a short-term exposure to spaceflight on the phenotype, genome, transcriptome and proteome of Escherichia coli

NASA Astrophysics Data System (ADS)

Li, Tianzhi; Chang, De; Xu, Huiwen; Chen, Jiapeng; Su, Longxiang; Guo, Yinghua; Chen, Zhenhong; Wang, Yajuan; Wang, Li; Wang, Junfeng; Fang, Xiangqun; Liu, Changting

2015-07-01

Escherichia coli (E. coli) is the most widely applied model organism in current biological science. As a widespread opportunistic pathogen, E. coli can survive not only by symbiosis with human, but also outside the host as well, which necessitates the evaluation of its response to the space environment. Therefore, to keep humans safe in space, it is necessary to understand how the bacteria respond to this environment. Despite extensive investigations for a few decades, the response of E. coli to the real space environment is still controversial. To better understand the mechanisms how E. coli overcomes harsh environments such as microgravity in space and to investigate whether these factors may induce pathogenic changes in E. coli that are potentially detrimental to astronauts, we conducted detailed genomics, transcriptomic and proteomic studies on E. coli that experienced 17 days of spaceflight. By comparing two flight strains LCT-EC52 and LCT-EC59 to a control strain LCT-EC106 that was cultured under the same temperature conditions on the ground, we identified metabolism changes, polymorphism changes, differentially expressed genes and proteins in the two flight strains. The flight strains differed from the control in the utilization of more than 30 carbon sources. Two single nucleotide polymorphisms (SNPs) and one deletion were identified in the flight strains. The expression level of more than 1000 genes altered in flight strains. Genes involved in chemotaxis, lipid metabolism and cell motility express differently. Moreover, the two flight strains also differed extensively from each other in terms of metabolism, transcriptome and proteome, indicating the impact of space environment on individual cells is heterogeneous and probably genotype-dependent. This study presents the first systematic profile of E. coli genome, transcriptome and proteome after spaceflight, which helps to elucidate the mechanism that controls the adaptation of microbes to the space environment.

Structured versus long-chain triglycerides: a safety, tolerance, and efficacy randomized study in colorectal surgical patients.

PubMed

Bellantone, R; Bossola, M; Carriero, C; Malerba, M; Nucera, P; Ratto, C; Crucitti, P; Pacelli, F; Doglietto, G B; Crucitti, F

1999-01-01

After trauma or surgery, researchers have suggested that medium-chain triglycerides have metabolic advantages, although they are toxic in large doses. To try to reduce this potential toxicity, structured lipids, which provide a higher oxidation rate, faster clearance from blood, improved nitrogen balance, and less accumulation in the reticuloendothelial system, could be used. Therefore, we evaluated, through a blind randomized study, the safety, tolerance, and efficacy of structured triglycerides, compared with long-chain triglycerides (LCT), in patients undergoing colorectal surgery. Nineteen patients were randomized to receive long-chain or structured triglycerides as a lipid source. They received the same amount of calories (27.2/kg/d), glucose (4 g/kg/d), protein (0.2 g/kg/d), and lipids (11.2 kcal/kg/d). Patients were evaluated during and after the treatment for clinical and laboratory variables, daily and cumulative nitrogen balance, urinary excretion of 3-methyl-histidine, and urinary 3-methylhistidine/creatinine ratio. No adverse effect that required the interruption of the treatment was observed. Triglyceride levels and clinical and laboratory variables were similar in the two groups. A predominantly positive nitrogen balance was observed from day 2 until day 5 in the LCT group and from day 1 until day 4 in the structured triglycerides group. The cumulative nitrogen balance (in grams) for days 1 to 3 was 9.7+/-5.2 in the experimental group and 4.4+/-11.8 in the control group (p = .2). For days 1 to 5 it was 10.7+/-10.5 and 6.5+/-17.9 (p = .05), respectively. The excretion of 3-methylhistidine was higher in the control group but decreased in the following days and was similar to the experimental group on day 5. This study represents the first report in which structured triglycerides are administered in postoperative patients to evaluate safety, tolerance, and efficacy. It suggests that Fe73403 is safe, well tolerated, and efficacious in terms of nitrogen balance when compared with LCT emulsion.

Structured triglyceride for parenteral nutrition: meta-analysis of randomized controlled trials.

PubMed

Zhou, Yong; Wu, Xiao-Ting; Li, Ni; Zhuang, Wen; Liu, Guanjian; Wu, Taixiang; Wei, Mao-Ling

2006-01-01

This study assessed the safety and efficacy of structured triglyceride (ST) for parenteral nutrition. A meta-analysis of all the relevant randomized controlled trials (RCTs) was performed. Clinical trials were identified from the following electronic databases: MEDLINE, EMBASE, the Cochrane Controlled Trials Register, Chinese Bio-medicine Database. The search was undertaken in March 2005. Language was restricted to Chinese and English. Literature references were checked at the same time. Only RCTs were extracted and evaluated by two reviewers independently of each other. The statistical analysis was performed by RevMan4.2 software which was provided by the Cochrane Collaboration. A P value of <0.05 was considered statistically significant. Ten RCTs involving 236 patients were included. Eight of them compared ST with the long-chain triglyceride (LCT), and the combined results showed that the ST had significant effect on resting energy expenditure (weighted mean difference [WMD] =1.54, 95%CI [ 1.26, 1.82], p<0.00001), plasma glycerol (WMD = 0.14, 95%CI [0.06, 0.22], P= 0.0007), free fatty acids (WMD=0.24, 95%CI [0.10, 0.37], P=0.0006), and beta-hydroxybutyric acid (WMD=0.14, 95%CI [0.06, 0.22], P=0.0007), but no differences was found regarding nitrogen balance (standardized mean difference [SMD] = 0.64, 95%CI [-0.30, 1.59], P=0.18), respiratory quotient (WMD =-0.02, 95%CI [-0.04, 0.01], P= 0.18), and plasma triglycerides (WMD = -0.10, 95%CI [-0.30, 0.10], P=0.32). Only two RCTs compared ST with the physical mixture of medium- and long-chain triglyceride (MCT/LCT), data from trials were not combined due to clinical differences between trials, and conclusions can not be drew from the present data. ST appeared to be safe and well tolerated. Further trials are required, especially compared with the MCT/LCT, with sufficient size and rigorous design.

[Diagnostic imaging and interventional therapy in hepatocarcinoma. Multicenter study of 290 cases].

PubMed

Dalla Palma, L; Pozzi Mucelli, R; Sponza, M; Bartolozzi, C; Lencioni, R; Florio, F; De Santis, M; Gandini, G; Matricardi, L; Rossi, C; Simonetti, G; Pocek, M

1997-01-01

We report the results of a multicenter study on the diagnosis and interventional therapy of hepatocellular carcinoma (HCC). The first aim--diagnosis--was to evaluate the sensitivity of 4 imaging techniques, namely ultrasonography (US), Computed Tomography (CT), digital arteriography (DSA) and Lipiodol CT (LCT), in HCC detection. The accuracy of these techniques was also investigated in tumor staging, which is important for treatment planning. Two hundred ninety patients underwent this imaging protocol. The patients were classified by tumor spread into three groups, namely group 1 (single HCCs < 5 cm), group 2 (multifocal HCCs with max. 3 nodules or tumor volume < 80 cc), group 3 (multifocal HCCs with more than 3 nodules and/or tumor volume > 80 cc). US and CT diagnosed more cases as group 1 and fewer cases as group 3 than DSA and LCT; the latter two techniques gave a similar classification. With LCT as the gold standard, US and CT understaged 27.9% and 26.5% of cases, respectively. Even though LCT is known to have 53% sensitivity, it is currently the most sensitive preoperative investigation and therefore the best tool for treatment planning. In surgical patients, however, intraoperative US, with its nearly 100% sensitivity, is suggested. The second aim--treatment--consisted in assessing the therapeutic efficacy of intraarterial chemoembolization (CEAT) versus percutaneous ethanol injection (PEI) in non advanced HCC and of CEAT versus no treatment (NT) in advanced HCC. Treatment efficacy was evaluated with the following randomized protocols: PEI versus CEAT in group 1, PEI versus CEAT in group 2 and CEAT versus NT in group 3. The data were analyzed relative to 215 patients for 6 to 30 months. The Kaplan-Meier method was used to calculate survival rates, which were, at 24 and 30 months, 72% and 72% for PEI and 72% and 52% for CEAT in group 1, 52% and 28% for PEI and 70% and 50% for CEAT in group 2 and finally 30% and 20% for NT and 45% and 30% for CEAT in group 3. In group 1, PEI appeared markedly superior to CEAT. In group 2, the difference between PEI and CEAT was not statistically significant; the results in this group indicate that CEAT should be considered when three nodules are present because of PEI invasiveness in these cases. In group 3, CEAT results were definitely better in the first two years, but there was no difference with NT patients at the end of the third year. Therefore, CEAT is indicated in advanced HCC because it improves the survival rate in the first 24 months. After this period, the survival time is not modified by treatment.

Foregrounding Knowledge in E-Learning Design: An Illustration in a Museum Setting

ERIC Educational Resources Information Center

Carvalho, Lucila; Dong, Andy; Maton, Karl

2015-01-01

The nature of knowledge, and the various forms knowledge may take, is a neglected aspect of the development of e-learning environments. This paper uses Legitimation Code Theory (LCT) to conceptualise the organising principles of knowledge practices. As we will illustrate, when it comes to the design of e-learning, the organising principles of the…

Learner Centered Teaching: Putting the Research on Learning into Practice

ERIC Educational Resources Information Center

Doyle, Terry

2011-01-01

This book presents the research-based case that Learner Centered Teaching (LCT) offers the best means to optimize student learning in college, and offers examples and ideas for putting it into practice, as well the underlying rationale. It also starts from the premise that many faculty are much closer to being learner centered teachers than they…

Recovering Knowledge for Science Education Research: Exploring the "Icarus Effect" in Student Work

ERIC Educational Resources Information Center

Georgiou, Helen; Maton, Karl; Sharma, Manjula

2014-01-01

Science education research has built a strong body of work on students' understandings but largely overlooked the nature of science knowledge itself. Legitimation Code Theory (LCT), a rapidly growing approach to education, offers a way of analyzing the organizing principles of knowledge practices and their effects on science education. This…

Lattice model of linear telechelic polymer melts. II. Influence of chain stiffness on basic thermodynamic properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Wen-Sheng, E-mail: wsxu@uchicago.edu; Freed, Karl F., E-mail: freed@uchicago.edu; Department of Chemistry, The University of Chicago, Chicago, Illinois 60637

2015-07-14

The lattice cluster theory (LCT) for semiflexible linear telechelic melts, developed in Paper I, is applied to examine the influence of chain stiffness on the average degree of self-assembly and the basic thermodynamic properties of linear telechelic polymer melts. Our calculations imply that chain stiffness promotes self-assembly of linear telechelic polymer melts that assemble on cooling when either polymer volume fraction ϕ or temperature T is high, but opposes self-assembly when both ϕ and T are sufficiently low. This allows us to identify a boundary line in the ϕ-T plane that separates two regions of qualitatively different influence of chainmore » stiffness on self-assembly. The enthalpy and entropy of self-assembly are usually treated as adjustable parameters in classical Flory-Huggins type theories for the equilibrium self-assembly of polymers, but they are demonstrated here to strongly depend on chain stiffness. Moreover, illustrative calculations for the dependence of the entropy density of linear telechelic polymer melts on chain stiffness demonstrate the importance of including semiflexibility within the LCT when exploring the nature of glass formation in models of linear telechelic polymer melts.« less

Solubility calculations of branched and linear amino acids using lattice cluster theory

NASA Astrophysics Data System (ADS)

Fischlschweiger, Michael; Enders, Sabine; Zeiner, Tim

2014-09-01

In this work, the activity coefficients and the solubility of amino acids in water were calculated using the lattice cluster theory (LCT) combined with the extended chemical association lattice model allowing self-association as well as cross-association. This permits the study of the influence of the amino acids structure on the thermodynamic properties for the first time. By the used model, the activity coefficient and solubilities of the investigated fourteen amino acids (glycine, alanine, γ-aminobutyric acid, dl-valine, dl-threonine, dl-methionine, l-leucine, l-glutamic acid, l-proline, hydroxyproline, histidine, l-arginine, α-amino valeric acid) could be described in good accordance with experimental data. In the case of different α-amino acids, but different hydrocarbon chains, the same interaction energy parameter can be used within the LCT. All studied amino acids could be modelled using the same parameter for the description of the amino acid association properties. The formed cross-associates contain more amino acids than expressed by the overall mole fraction of the solution. Moreover, the composition of the cross-associates depends on temperature, where the amount of amino acids increases with increasing temperature.

Steering Electromagnetic Fields in MRI: Investigating Radiofrequency Field Interactions with Endogenous and External Dielectric Materials for Improved Coil Performance at High Field

NASA Astrophysics Data System (ADS)

Vaidya, Manushka

Although 1.5 and 3 Tesla (T) magnetic resonance (MR) systems remain the clinical standard, the number of 7 T MR systems has increased over the past decade because of the promise of higher signal-to-noise ratio (SNR), which can translate to images with higher resolution, improved image quality and faster acquisition times. However, there are a number of technical challenges that have prevented exploiting the full potential of ultra-high field (≥ 7 T) MR imaging (MRI), such as the inhomogeneous distribution of the radiofrequency (RF) electromagnetic field and specific energy absorption rate (SAR), which can compromise image quality and patient safety. To better understand the origin of these issues, we first investigated the dependence of the spatial distribution of the magnetic field associated with a surface RF coil on the operating frequency and electrical properties of the sample. Our results demonstrated that the asymmetries between the transmit (B1+) and receive (B 1-) circularly polarized components of the magnetic field, which are in part responsible for RF inhomogeneity, depend on the electric conductivity of the sample. On the other hand, when sample conductivity is low, a high relative permittivity can result in an inhomogeneous RF field distribution, due to significant constructive and destructive interference patterns between forward and reflected propagating magnetic field within the sample. We then investigated the use of high permittivity materials (HPMs) as a method to alter the field distribution and improve transmit and receive coil performance in MRI. We showed that HPM placed at a distance from an RF loop coil can passively shape the field within the sample. Our results showed improvement in transmit and receive sensitivity overlap, extension of coil field-of-view, and enhancement in transmit/receive efficiency. We demonstrated the utility of this concept by employing HPM to improve performance of an existing commercial head coil for the inferior regions of the brain, where the specific coil's imaging efficiency was inherently poor. Results showed a gain in SNR, while the maximum local and head SAR values remained below the prescribed limits. We showed that increasing coil performance with HPM could improve detection of functional MR activation during a motor-based task for whole brain fMRI. Finally, to gain an intuitive understanding of how HPM improves coil performance, we investigated how HPM separately affects signal and noise sensitivity to improve SNR. For this purpose, we employed a theoretical model based on dyadic Green's functions to compare the characteristics of current patterns, i.e. the optimal spatial distribution of coil conductors, that would either maximize SNR (ideal current patterns), maximize signal reception (signal-only optimal current patterns), or minimize sample noise (dark mode current patterns). Our results demonstrated that the presence of a lossless HPM changed the relative balance of signal-only optimal and dark mode current patterns. For a given relative permittivity, increasing the thickness of the HPM altered the magnitude of the currents required to optimize signal sensitivity at the voxel of interest as well as decreased the net electric field in the sample, which is associated, via reciprocity, to the noise received from the sample. Our results also suggested that signal-only current patterns could be used to identify HPM configurations that lead to high SNR gain for RF coil arrays. We anticipate that physical insights from this work could be utilized to build the next generation of high performing RF coils integrated with HPM.

Effects of Emotional Intelligence and Locus of Control Training on the Psychological Well-Being of Adolescents with Visual Impairments in Nigeria

ERIC Educational Resources Information Center

Eniola, M. S.; Ajobiewe, Abthonia Ifeoma

2013-01-01

This current study, investigated the relative effectiveness of Emotional Intelligence Training (EIT) and Locus of Control Training (LCT) on the psychological well-being of adolescent with visual impairment. The pretest-posttest control group experimental design with a 3x2x2 factorial matrix was used. The participants were 120 adolescents with…

Medium-Chain Triglycerides in Combination with Leucine and Vitamin D Increase Muscle Strength and Function in Frail Elderly Adults in a Randomized Controlled Trial.

PubMed

Abe, Sakiko; Ezaki, Osamu; Suzuki, Motohisa

2016-05-01

Sarcopenia, the loss of skeletal muscle mass, strength, and function, is common in elderly individuals but difficult to treat. A combination of nutrients was investigated to treat sarcopenia in very frail elderly adults. We enrolled 38 elderly nursing home residents (11 men and 27 women with a mean ± SD age of 86.6 ± 4.8 y) in a 3-mo randomized, controlled, single-blind, parallel group trial. The participants were randomly allocated to 3 groups. The first group received a daily l-leucine (1.2 g) and cholecalciferol (20 μg)-enriched supplement with 6 g medium-chain triglycerides (TGs) (MCTs) (LD + MCT); the second group received the same leucine and cholecalciferol-enriched supplement with 6 g long-chain TGs (LD + LCT); and the third group did not receive any supplements (control). The supplement and oils were taken at dinner, and changes in muscle mass, strength, and function were monitored. The increase in body weight in the LD + MCT (1.1 ± 1.0 kg) and LD + LCT (0.8 ± 1.1 kg) groups was greater than that in the control group (-0.5 ± 0.9 kg) (P < 0.05). After 3 mo, participants in the LD + MCT group had a 13.1% increase in right-hand grip strength (1.2 ± 1.0 kg, P < 0.01), a 12.5% increase in walking speed (0.078 ± 0.080 m/s, P < 0.05), a 68.2% increase in a 10-s leg open-and-close test performance (2.31 ± 1.68 n/10 s, P < 0.001), and a 28.2% increase in peak expiratory flow (53 ± 59 L/min, P < 0.01). No significant improvements in muscle mass, strength, or function were observed in the LD + LCT or control groups. The combined supplementation of MCTs (6 g), leucine-rich amino acids, and cholecalciferol at dinner may improve muscle strength and function in frail elderly individuals. This trial was registered at the University Hospital Medical Information Network Clinical Trials Registry as UMIN000017567. © 2016 American Society for Nutrition.

Effects of medium-chain triglycerides on intestinal morphology and energy metabolism of intrauterine growth retarded weanling piglets.

PubMed

Zhang, Li-Li; Zhang, Hao; Li, Yue; Wang, Tian

2017-06-01

It has been shown that there is a relationship between intrauterine growth retardation (IUGR) and postnatal intestinal damage involved in energy deficits. Therefore, the present study was conducted to investigate the effect of medium-chain triglycerides (MCT) on the intestinal morphology, intestinal function and energy metabolism of piglets with IUGR. At weaning (21 ± 1.1 d of age), 24 IUGR piglets and 24 normal birth weight (NBW) piglets were selected according to their birth weights (BW) (IUGR: 0.95 ± 0.04 kg BW; NBW: 1.58 ± 0.04 kg BW) and their weights at the time of weaning (IUGR: 5.26 ± 0.15 kg BW; NBW: 6.98 ± 0.19 kg BW). The piglets were fed a diet of either long-chain triglycerides (LCT) (containing 5% LCT) or MCT (containing 1% LCT and 4% MCT) for 28 d. Then, the piglets' intestinal morphology, biochemical parameters and mRNA abundance related to intestinal damage and energy metabolism were determined. IUGR was found to impair intestinal morphology, with evidence of decreased villus height and increased crypt depth; however, these negative effects of IUGR were ameliorated by MCT treatment. IUGR piglets showed compromised intestinal digestion and absorption functions when compared with NBW piglets. However, feeding MCT increased the maltase activity in the jejunum and alleviated IUGR-induced reductions in plasma d-xylose concentrations and jejunal sucrase activity. IUGR decreased the efficiency of the piglets' intestinal energy metabolism; however, piglets fed an MCT diet exhibited increased adenosine triphosphate (ATP) concentrations and ATP synthase F1 complex beta polypeptide expression, as well as decreased adenosine monophosphate-activated kinase alpha 1 expression in the jejunum of piglets. In addition, up-regulation of the piglets' citrate synthase and succinate dehydrogenase levels was found to occur following MCT treatment at both the activity and the transcriptional levels of the jejunum. Therefore, it can be postulated that MCT treatment has beneficial effects in alleviating IUGR-induced intestinal morphologic damage, which is associated with improved intestinal energy metabolism.

Stability of MCT/LCT-based total nutrient admixtures for neonatal use over 30 hours at room temperature: applying pharmacopeial standards.

PubMed

Driscoll, David F; Silvestri, Anthony P; Bistrian, Bruce R

2010-01-01

United States Pharmacopeial Chapter <729> places a limit on the percentage of large fat globules >5 microm, expressed as a PFAT5 of <0.05% for all native lipid emulsions. Some adult total nutrient admixtures (TNAs) have also remained below this limit for up to 48 hours. In 2003, medium-chain/long-chain triglyceride (MCT/LCT)-based neonatal TNAs with between 2% and 3% amino acid (AA) concentrations were shown to be similarly stable by the PFAT5 parameter. Stability assessment of neonatal TNAs with AA <2% or > or =3% were tested. Eight neonatal TNAs with various combinations of AA (1%, 1.5%, 3%, and 4%), glucose (G; 5% and 10%), and MCT/LCT (ML; 2% and 4%) and standard concentrations of additives were tested in triplicate (n = 24) over 30 hours (immediately after mixing, then at 6, 24, and 30 hours) at 25 degrees C +/- 2 degrees C. PFAT5 determinations for all 24 formulations were made in duplicate, immediately after mixing, and then at 6, 24, and 30 hours later. Mean droplet size (MDS) and pH were assessed at the outset and end of the study. The differences in the PFAT5 levels were significant (P < .001) by a 2-way analysis of variance based on formula and time as the independent variables. The TNAs with 1% and 1.5% AA with all Gs and MLs (group 1, n = 12) had PFAT5 levels >0.05% (up to 0.50%) in most samples (68 of 96 samples, or 71% of cases) in the study, whereas in the same TNAs, but made with 3% and 4% AA (group 2, n = 12), 100% of samples (all 96 cases) had PFAT5 levels <0.05% (up to 0.04%), and this difference was significant (P < .001). Pairwise comparisons between groups based on overall values of PFAT5, MDS, and pH showed significant differences between groups for all variables. For neonatal TNAs, AA level is the most sensitive determinant of stability, and the PFAT5 parameter is the most sensitive indicator of stability.

Echo-Planar Imaging-Based, J-Resolved Spectroscopic Imaging for Improved Metabolite Detection in Prostate Cancer

DTIC Science & Technology

2014-10-01

Imaging (EP-JRESI); Citrate, Choline, Creatine , Spermine, 3Tesla MRI scanner, Endo-rectal MR coil, WET Water Suppression, prostate cancer (PCa...spectroscopic imaging are due to the overlap of metabolite resonances, quantifying few metabolites only (citrate (Cit), choline (Ch), creatine (Cr...concentrations of citrate (Cit), creatine (Cr), choline (Ch) and polyamines that are used to detect and diagnose PCa (2). The challenging task in 1D MRS

Quantitative Mixing Measurements of a Supersonic Injection COIL Nozzle with Trip Jets

DTIC Science & Technology

2008-06-13

6. AUTHOR( S ) 5d. PROJECT NUMBER 4866 Carrie A. Noren 5e. TASK NUMBER LB 5f. WORK UNIT NUMBER 11 7. PERFORMING ORGANIZATION NAME( S ) AND...ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING / MONITORING AGENCY NAME( S ) AND ADDRESS(ES) 10...SPONSOR/MONITOR’S ACRONYM( S ) Air Force Research Laboratory 3550 Aberdeen Ave SE 11. SPONSOR/MONITOR’S REPORT Kirtland AFB, NM 87117-5776

Low Energy Consumption Hydraulic Techniques

DTIC Science & Technology

1988-08-30

usually at welds . 1-15 SECTION II PHASE I - ADVANCED AIRCRAFT HYDRAULIC SYSTEM SELECTION Phase I included Task 1 selection of the aircraft and definition...face was bronze plated. The bearings were 52100 tool steel and the pistons were M50 tool steel. The shoe faces were 4140 with bronze plate and the back...o Magnet assembly o Coil assembly DDV Force Motor - -- ,..._(First Stage) oeMain Control Valve __(Second Sae Main Control Valve LVDT Figure 282 Direct

Dynamic Multi-Coil Technique (DYNAMITE) Shimming of the Rat Brain at 11.7 Tesla

PubMed Central

Juchem, Christoph; Herman, Peter; Sanganahalli, Basavaraju G.; Brown, Peter B.; McIntyre, Scott; Nixon, Terence W.; Green, Dan; Hyder, Fahmeed; de Graaf, Robin A.

2014-01-01

The in vivo rat model is a workhorse in neuroscience research, preclinical studies and drug development. A repertoire of MR tools has been developed for its investigation, however, high levels of B0 magnetic field homogeneity are required for meaningful results. The homogenization of magnetic fields in the rat brain, i.e. shimming, is a difficult task due to a multitude of complex, susceptibility-induced field distortions. Conventional shimming with spherical harmonic (SH) functions is capable of compensating shallow field distortions in limited areas, e.g. in the cortex, but performs poorly in difficult-to-shim subcortical structures or for the entire brain. Based on the recently introduced multi-coil approach for magnetic field modeling, the DYNAmic Multi-coIl TEchnique (DYNAMITE) is introduced for magnetic field shimming of the in vivo rat brain and its benefits for gradient-echo echo-planar imaging (EPI) are demonstrated. An integrated multi-coil/radio-frequency (MC/RF) system comprising 48 individual localized DC coils for B0 shimming and a surface transceive RF coil has been developed that allows MR investigations of the anesthetized rat brain in vivo. DYNAMITE shimming with this MC/RF setup is shown to reduce the B0 standard deviation to a third of that achieved with current shim technology employing static first through third order SH shapes. The EPI signal over the rat brain increased by 31% and a 24% gain in usable EPI voxels could be realized. DYNAMITE shimming is expected to critically benefit a wide range of preclinical and neuroscientific MR research. Improved magnetic field homogeneity, along with the achievable large brain coverage of this method will be crucial when signal pathways, cortical circuitry or the brain’s default network are studied. Along with the efficiency gains of MC-based shimming compared to SH approaches demonstrated recently, DYNAMITE shimming has the potential to replace conventional SH shim systems in small bore animal scanners. PMID:24839167

Performance assessment of radiant cooling system integrated with desiccant assisted DOAS with solar regeneration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khan, Yasin; Singh, Gaurav; Mathur, Jyotirmay

The Radiant cooling system integrated with Dedicated Outdoor Air System (DOAS) is a viable substitution for conventional all air system in order to reduce primary energy consumption, as it decouples the cooling and ventilation task. In DOAS major portion of energy is consumed in cooling coil where it dehumidifies the process supply air. This study describes an alternate solution for dehumidification, with the substitution of the desiccant wheel with solar regeneration in place of a chilled water coil based dehumidifier. In this paper, simulations were carried out using EnergyPlus on a reference medium office building to investigate the contribution ofmore » solar energy towards the total energy consumption of desiccant assisted DOAS with radiant cooling system. To evaluate the system performance and energy saving potential, desiccant based DOAS is compared with cooling coil assisted DOAS integrated with Radiant cooling system. Simulations were carried out for different solar collector area to evaluate primary energy savings. Results indicate that from 7.4 % to 28.6 % energy saving (according to different collector area) can be achieved due to the solar regeneration in desiccant assisted DOAS, the impact of different solar collector area on potential of energy savings is also described.« less

Performance assessment of radiant cooling system integrated with desiccant assisted DOAS with solar regeneration

DOE PAGES

Khan, Yasin; Singh, Gaurav; Mathur, Jyotirmay; ...

2017-06-13

The Radiant cooling system integrated with Dedicated Outdoor Air System (DOAS) is a viable substitution for conventional all air system in order to reduce primary energy consumption, as it decouples the cooling and ventilation task. In DOAS major portion of energy is consumed in cooling coil where it dehumidifies the process supply air. This study describes an alternate solution for dehumidification, with the substitution of the desiccant wheel with solar regeneration in place of a chilled water coil based dehumidifier. In this paper, simulations were carried out using EnergyPlus on a reference medium office building to investigate the contribution ofmore » solar energy towards the total energy consumption of desiccant assisted DOAS with radiant cooling system. To evaluate the system performance and energy saving potential, desiccant based DOAS is compared with cooling coil assisted DOAS integrated with Radiant cooling system. Simulations were carried out for different solar collector area to evaluate primary energy savings. Results indicate that from 7.4 % to 28.6 % energy saving (according to different collector area) can be achieved due to the solar regeneration in desiccant assisted DOAS, the impact of different solar collector area on potential of energy savings is also described.« less

Adaptive Strategy Selection in Decision Making.

DTIC Science & Technology

1986-07-31

information processing capabilities of a decision maker, given any " reasonable " time limit for making the decision. If use of a more normative rule...DECISION MAKING JOHN W. PAYNE DTIC DUKE UNIVERSITY L.CT E AUG 13 JAMES R. BETTMAN DUKE. UNIVERSITY ERIC J. JOHNSON CARNEGIE-MELLON UNIVERSITY...REPORT & PERIOD COVERED ADAPTIVE STRATEGY SELECTION IN DECISION MAKING Research 6. PERFORMING ORO. REPORT NUMSER 7. AUTNORfe) e. CONTRACT ON GRANT

A spatial econometric analysis of land-use change with land cover trends data: an application to the Pacific Northwest

Treesearch

David J. Lewis; Ralph J. Alig

2014-01-01

This paper develops a plot-level spatial econometric land-use model and estimates it with U.S. Geological Survey Land Cover Trends (LCT) geographic information system panel data for the western halves of the states of Oregon and Washington. The discrete-choice framework we use models plot-scale choices of the three dominant land uses in this region: forest, agriculture...

Three years coherent space to ground links: performance results and outlook for the optical ground station equipped with adaptive optics

NASA Astrophysics Data System (ADS)

Gregory, M.; Troendle, D.; Muehlnikel, G.; Heine, F.; Meyer, R.; Lutzer, M.; Czichy, R.

2013-03-01

Tesat is performing inter-satellite links (ISLs) for over 5 years now. Besides the successful demonstration of the suitability of coherent laser communication for high speed data transmission in space, Tesat has also conducted two major satellite to ground link (SGL) campaigns during the last 3 years. A transportable ground station has been developed to measure the impact of atmospheric turbulence to the coherent system. The SGLs have been performed between the Tesat optical ground station and the two LEO satellites TerraSAR-X and NFIRE, both equipped with a Tesat LCT. The capability of the LCTs of measuring the signal intensity on a direct detection sensor and on a coherent sensor simultaneously makes the system unique for investigating the atmospheric distortion impacts. In this paper the main results of the SGL campaigns are presented, including BER performance for the uplink and downlink. Measured scintillation profiles versus elevation angles at different weather conditions are illustrated. Finally preliminary results of an adaptive optics system are presented that has been developed to be used in the transportable adaptive optical ground station (T-AOGS) acting as the counter terminal for the LCT mounted on Alphasat, a geostationary satellite of the European Space Agency (ESA), in autumn 2013.

High-speed laser communications in UAV scenarios

NASA Astrophysics Data System (ADS)

Griethe, Wolfgang; Gregory, Mark; Heine, Frank; Kämpfner, Hartmut

2011-05-01

Optical links, based on coherent homodyne detection and BPSK modulation with bidirectional data transmission of 5.6 Gbps over distances of about 5,000 km and BER of 10-8, have been sufficiently verified in space. The verification results show that this technology is suitable not only for space applications but also for applications in the troposphere. After a brief description of the Laser Communication Terminal (LCT) for space applications, the paper consequently discusses the future utilization of satellite-based optical data links for Beyond Line of Sight (BLOS) operations of High Altitude Long Endurance (HALE) Unmanned Aerial Vehicles (UAV). It is shown that the use of optical frequencies is the only logical consequence of an ever-increasing demand for bandwidth. In terms of Network Centric Warfare it is highly recommended that Unmanned Aircraft Systems (UAS) of the future should incorporate that technology which allows almost unlimited bandwidth. The advantages of optical communications especially for Intelligence, Surveillance and Reconnaissance (ISR) are underlined. Moreover, the preliminary design concept of an airborne laser communication terminal is described. Since optical bi-directional links have been tested between a LCT in space and a TESAT Optical Ground Station (OGS), preliminary analysis on tracking and BER performance and the impact of atmospheric disturbances on coherent links will be presented.

An innovation diffusion model of a local electricity network that is influenced by internal and external factors

NASA Astrophysics Data System (ADS)

Hattam, Laura; Greetham, Danica Vukadinović

2018-01-01

Haynes et al. (1977) derived a nonlinear differential equation to determine the spread of innovations within a social network across space and time. This model depends upon the imitators and the innovators within the social system, where the imitators respond to internal influences, whilst the innovators react to external factors. Here, this differential equation is applied to simulate the uptake of a low-carbon technology (LCT) within a real local electricity network that is situated in the UK. This network comprises of many households that are assigned to certain feeders. Firstly, travelling wave solutions of Haynes' model are used to predict adoption times as a function of the imitation and innovation influences. Then, the grid that represents the electricity network is created so that the finite element method (FEM) can be implemented. Next, innovation diffusion is modelled with Haynes' equation and the FEM, where varying magnitudes of the internal and external pressures are imposed. Consequently, the impact of these model parameters is investigated. Moreover, LCT adoption trajectories at fixed feeder locations are calculated, which give a macroscopic understanding of the uptake behaviour at specific network sites. Lastly, the adoption of LCTs at a household level is examined, where microscopic and macroscopic approaches are combined.

Structural and mechanical properties of organogels: Role of oil and gelator molecular structure.

PubMed

Cerqueira, Miguel A; Fasolin, Luiz H; Picone, Carolina S F; Pastrana, Lorenzo M; Cunha, Rosiane L; Vicente, António A

2017-06-01

This work aims at evaluating the influence of oil and gelator structure on organogels' properties through rheological measurements, polarized microscopy and small-angle X-ray scattering (SAXS). Four different food-grade gelators (glyceryl tristearate - GT; sorbitan tristearate - ST; sorbitan monostearate - SM and glyceryl monostearate - GM) were tested in medium-chain triglyceride and high oleic sunflower (MCT and LCT, respectively) oil phases. Organogels were prepared by mixing the oil phase and gelator at different concentrations (5, 10, 15, 20 and 25%) at 80°C during 30min. All organogels presented birefringence confirming the formation of a crystalline structure that changed with the increase of the gelator concentration. Through the evaluation of SAXS peaks it has been confirmed that all structures were organized as lamellas but with different d-spacing values. These particularities at micro- and nanoscale level lead to differences in rheological properties of organogels. Results showed that the oil type (i.e. medium- and long-chain triglyceride) and hydrophilic head of gelators (i.e. sorbitan versus glyceryl) exert influence on the organogels physical properties, but the presence of monostearate leads to the formation of stronger organogels. Moreover, gels produced with LCT were stronger and gelled at lower organogelator concentration than MCT. Copyright © 2017 Elsevier Ltd. All rights reserved.

Structured triglyceride emulsions in parenteral nutrition.

PubMed

Chambrier, C; Lauverjat, M; Bouletreau, P

2006-08-01

Over the past 3 decades, various concepts for IV fat emulsions (IVFE) have been developed. A randomized, structured-lipid emulsion based on an old technology has recently become available. This structured-lipid emulsion is produced by mixing medium-chain triglycerides and long-chain triglycerides, then allowing hydrolysis to form free fatty acids, followed by random transesterification of the fatty acids into mixed triglyceride molecules. Studies in animals have shown an improvement in nitrogen balance with the use of these lipid emulsions. Only 8 human clinical studies with these products have been performed. The results of these human clinical studies have been less promising than the animal studies; however, an improvement in nitrogen balance and lipid metabolism exceeds results associated with infusion of long-chain triglycerides (LCT) or a physical mixture of long-chain triglycerides and medium-chain triglycerides (LCT-MCT). Structured-lipid emulsion seems to induce less elevation in serum liver function values compared with standard IVFEs. In addition, structured-lipid emulsions have no detrimental effect on the reticuloendothelial system. Further studies are necessary in order to recommend the use of structured-lipid emulsions. The clinical community hopes that chemically defined structured triglycerides will make it possible to determine the distribution of specific fatty acids on a specific position on the glycerol core and therefore obtain specific activity for a specific clinical situation.

A fast and flexible MRI system for the study of dynamic vocal tract shaping.

PubMed

Lingala, Sajan Goud; Zhu, Yinghua; Kim, Yoon-Chul; Toutios, Asterios; Narayanan, Shrikanth; Nayak, Krishna S

2017-01-01

The aim of this work was to develop and evaluate an MRI-based system for study of dynamic vocal tract shaping during speech production, which provides high spatial and temporal resolution. The proposed system utilizes (a) custom eight-channel upper airway coils that have high sensitivity to upper airway regions of interest, (b) two-dimensional golden angle spiral gradient echo acquisition, (c) on-the-fly view-sharing reconstruction, and (d) off-line temporal finite difference constrained reconstruction. The system also provides simultaneous noise-cancelled and temporally aligned audio. The system is evaluated in 3 healthy volunteers, and 1 tongue cancer patient, with a broad range of speech tasks. We report spatiotemporal resolutions of 2.4 × 2.4 mm 2 every 12 ms for single-slice imaging, and 2.4 × 2.4 mm 2 every 36 ms for three-slice imaging, which reflects roughly 7-fold acceleration over Nyquist sampling. This system demonstrates improved temporal fidelity in capturing rapid vocal tract shaping for tasks, such as producing consonant clusters in speech, and beat-boxing sounds. Novel acoustic-articulatory analysis was also demonstrated. A synergistic combination of custom coils, spiral acquisitions, and constrained reconstruction enables visualization of rapid speech with high spatiotemporal resolution in multiple planes. Magn Reson Med 77:112-125, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Cooling a solar telescope enclosure: plate coil thermal analysis

NASA Astrophysics Data System (ADS)

Gorman, Michael; Galapon, Chriselle; Montijo, Guillermo; Phelps, LeEllen; Murga, Gaizka

2016-08-01

The climate of Haleakalā requires the observatories to actively adapt to changing conditions in order to produce the best possible images. Observatories need to be maintained at a temperature closely matching ambient or the images become blurred and unusable. The Daniel K. Inouye Solar Telescope is a unique telescope as it will be active during the day as opposed to the other night-time stellar observatories. This means that it will not only need to constantly match the ever-changing temperature during the day, but also during the night so as not to sub-cool and affect the view field of other telescopes while they are in use. To accomplish this task, plate coil heat exchanger panels will be installed on the DKIST enclosure that are designed to keep the temperature at ambient temperature +0°C/-4°C. To verify the feasibility of this and to validate the design models, a test rig has been installed at the summit of Haleakalā. The project's purpose is to confirm that the plate coil panels are capable of maintaining this temperature throughout all seasons and involved collecting data sets of various variables including pressures, temperatures, coolant flows, solar radiations and wind velocities during typical operating hours. Using MATLAB, a script was written to observe the plate coil's thermal performance. The plate coil did not perform as expected, achieving a surface temperature that was generally 2ºC above ambient temperature. This isn't to say that the plate coil does not work, but the small chiller used for the experiment was undersized resulting in coolant pumped through the plate coil that was not supplied at a low enough temperature. Calculated heat depositions were about 23% lower than that used as the basis of the design for the hillers to be used on the full system, a reasonable agreement given the fact that many simplifying assumptions were used in the models. These were not carried over into the testing. The test rig performance showing a 23% margin provides a high degree of confidence for the performance of the full system when it is installed. If time allows, additional testing could be done that includes additional incident angles and times of day. This would allow a more complete analysis. If additional testing were to be performed, it's recommended to use a larger chiller capable of reaching lower temperatures. The test rig design could also be optimized in order to bring the plate coil up to its maximum efficiency. In the future, the script could be rewritten in a different computer language, so that the data could be solved for quicker. Further analysis could also include different types of coolants.

Genome-Wide Identification of Arabidopsis Coiled-Coil Proteins and Establishment of the ARABI-COIL Database1

PubMed Central

Rose, Annkatrin; Manikantan, Sankaraganesh; Schraegle, Shannon J.; Maloy, Michael A.; Stahlberg, Eric A.; Meier, Iris

2004-01-01

Increasing evidence demonstrates the importance of long coiled-coil proteins for the spatial organization of cellular processes. Although several protein classes with long coiled-coil domains have been studied in animals and yeast, our knowledge about plant long coiled-coil proteins is very limited. The repeat nature of the coiled-coil sequence motif often prevents the simple identification of homologs of animal coiled-coil proteins by generic sequence similarity searches. As a consequence, counterparts of many animal proteins with long coiled-coil domains, like lamins, golgins, or microtubule organization center components, have not been identified yet in plants. Here, all Arabidopsis proteins predicted to contain long stretches of coiled-coil domains were identified by applying the algorithm MultiCoil to a genome-wide screen. A searchable protein database, ARABI-COIL (http://www.coiled-coil.org/arabidopsis), was established that integrates information on number, size, and position of predicted coiled-coil domains with subcellular localization signals, transmembrane domains, and available functional annotations. ARABI-COIL serves as a tool to sort and browse Arabidopsis long coiled-coil proteins to facilitate the identification and selection of candidate proteins of potential interest for specific research areas. Using the database, candidate proteins were identified for Arabidopsis membrane-bound, nuclear, and organellar long coiled-coil proteins. PMID:15020757

Modular Rocket Engine Control Software (MRECS)

NASA Technical Reports Server (NTRS)

Tarrant, C.; Crook, J.

1998-01-01

The Modular Rocket Engine Control Software (MRECS) Program is a technology demonstration effort designed to advance the state-of-the-art in launch vehicle propulsion systems. Its emphasis is on developing and demonstrating a modular software architecture for advanced engine control systems that will result in lower software maintenance (operations) costs. It effectively accommodates software requirement changes that occur due to hardware technology upgrades and engine development testing. Ground rules directed by MSFC were to optimize modularity and implement the software in the Ada programming language. MRECS system software and the software development environment utilize Commercial-Off-the-Shelf (COTS) products. This paper presents the objectives, benefits, and status of the program. The software architecture, design, and development environment are described. MRECS tasks are defined and timing relationships given. Major accomplishments are listed. MRECS offers benefits to a wide variety of advanced technology programs in the areas of modular software architecture, reuse software, and reduced software reverification time related to software changes. MRECS was recently modified to support a Space Shuttle Main Engine (SSME) hot-fire test. Cold Flow and Flight Readiness Testing were completed before the test was cancelled. Currently, the program is focused on supporting NASA MSFC in accomplishing development testing of the Fastrac Engine, part of NASA's Low Cost Technologies (LCT) Program. MRECS will be used for all engine development testing.

Coiled-coil protein composition of 22 proteomes--differences and common themes in subcellular infrastructure and traffic control.

PubMed

Rose, Annkatrin; Schraegle, Shannon J; Stahlberg, Eric A; Meier, Iris

2005-11-16

Long alpha-helical coiled-coil proteins are involved in diverse organizational and regulatory processes in eukaryotic cells. They provide cables and networks in the cyto- and nucleoskeleton, molecular scaffolds that organize membrane systems and tissues, motors, levers, rotating arms, and possibly springs. Mutations in long coiled-coil proteins have been implemented in a growing number of human diseases. Using the coiled-coil prediction program MultiCoil, we have previously identified all long coiled-coil proteins from the model plant Arabidopsis thaliana and have established a searchable Arabidopsis coiled-coil protein database. Here, we have identified all proteins with long coiled-coil domains from 21 additional fully sequenced genomes. Because regions predicted to form coiled-coils interfere with sequence homology determination, we have developed a sequence comparison and clustering strategy based on masking predicted coiled-coil domains. Comparing and grouping all long coiled-coil proteins from 22 genomes, the kingdom-specificity of coiled-coil protein families was determined. At the same time, a number of proteins with unknown function could be grouped with already characterized proteins from other organisms. MultiCoil predicts proteins with extended coiled-coil domains (more than 250 amino acids) to be largely absent from bacterial genomes, but present in archaea and eukaryotes. The structural maintenance of chromosomes proteins and their relatives are the only long coiled-coil protein family clearly conserved throughout all kingdoms, indicating their ancient nature. Motor proteins, membrane tethering and vesicle transport proteins are the dominant eukaryote-specific long coiled-coil proteins, suggesting that coiled-coil proteins have gained functions in the increasingly complex processes of subcellular infrastructure maintenance and trafficking control of the eukaryotic cell.

Coiled-coil protein composition of 22 proteomes – differences and common themes in subcellular infrastructure and traffic control

PubMed Central

Rose, Annkatrin; Schraegle, Shannon J; Stahlberg, Eric A; Meier, Iris

2005-01-01

Background Long alpha-helical coiled-coil proteins are involved in diverse organizational and regulatory processes in eukaryotic cells. They provide cables and networks in the cyto- and nucleoskeleton, molecular scaffolds that organize membrane systems and tissues, motors, levers, rotating arms, and possibly springs. Mutations in long coiled-coil proteins have been implemented in a growing number of human diseases. Using the coiled-coil prediction program MultiCoil, we have previously identified all long coiled-coil proteins from the model plant Arabidopsis thaliana and have established a searchable Arabidopsis coiled-coil protein database. Results Here, we have identified all proteins with long coiled-coil domains from 21 additional fully sequenced genomes. Because regions predicted to form coiled-coils interfere with sequence homology determination, we have developed a sequence comparison and clustering strategy based on masking predicted coiled-coil domains. Comparing and grouping all long coiled-coil proteins from 22 genomes, the kingdom-specificity of coiled-coil protein families was determined. At the same time, a number of proteins with unknown function could be grouped with already characterized proteins from other organisms. Conclusion MultiCoil predicts proteins with extended coiled-coil domains (more than 250 amino acids) to be largely absent from bacterial genomes, but present in archaea and eukaryotes. The structural maintenance of chromosomes proteins and their relatives are the only long coiled-coil protein family clearly conserved throughout all kingdoms, indicating their ancient nature. Motor proteins, membrane tethering and vesicle transport proteins are the dominant eukaryote-specific long coiled-coil proteins, suggesting that coiled-coil proteins have gained functions in the increasingly complex processes of subcellular infrastructure maintenance and trafficking control of the eukaryotic cell. PMID:16288662

Southeast Asia Report, Number 1302

DTIC Science & Technology

1983-06-21

Leaders 25 LAOS Foreign Ministry on S. African Bombing of Maputo 26 Briefs Foreign Minister Delegation 27 Soviet Transport Talks 27 Return From...Successor to Laurente (THE VISAYAN HERALD, 3 May 83) 46 Briefs NPA Leader Sick 47 Poor Turnout at Protest Rally 47 Rebels Abandon Cebu Safe Houses 47...THE NATION REVIEW, 10 May 83) 50 VOFA Urges SRV Compliance With UN Resolution (Voice of Free Asia, 25 May 83) 52 LCT Leader Says

Effects of two ergonomic improvements in brazing coils of air-handler units.

PubMed

Loo, H S; Yeow, Paul H P

2015-11-01

The research aims to address the physically loading task and quality and productivity problems in the brazing of coils of air-handler units. Eight operators participated in two intervention studies conducted in a factory in Malaysia to compare the status quo brazing with (1) the use of a new twin-brazing torch that replaced the single-brazing gun and (2) brazing in a sitting position. The outcome measures are related to quality, productivity, monetary costs, body postures and symptoms. After baseline, Interventions I and II were applied for 3 months respectively. The results show a 58.9% quality improvement, 140% productivity increase and 113 times ROI. There was also a reduction in poor work postures e.g. in the raising of the arms and shoulders; bending, twisting and extending of the neck; and bending of left and right wrists, and the back. This research can be replicated in other factories that share similar processes. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Measurement of the controlled variable during heating of Ti6Al4V for thixoforging

NASA Astrophysics Data System (ADS)

Gerlach, O.; Lechler, A.; Verl, A.

2018-02-01

Controlled heating of metal billets into the semi-solid state for thixoforming is a challenging task, mainly due to the difficulties in measuring the liquid fraction of the billet during heating. Past research primarily focused on methods measuring the liquid fraction during heating of low-melting aluminium alloys. One of these methods is time constant measurement, a contactless measurement method that uses the heating coil as a sensor. The current through the coil is used to determine the electrical time constant of the heating circuit, which itself is influenced by the specific resistance of the billet inside the coil. While previous works focused on the suitability of this method for industrial applications using aluminum alloys, this paper extends this research to the high-melting titanium alloy Ti6Al4V. This alloys shows high strength, low density and excellent corrosion resistance. It is therefore used to produce light-weight and durable components for medical and aerospace applications. Ti6Al4V is an expensive and difficult to machine alloy. Thus, it is an interesting alloy for thixoforging. However, heating of the billet into a homogeneous state of defined liquid fraction is difficult due to the poor thermal conductivity of Ti6Al4V. This paper analyses the potential of using time constant measurement for controlled heating of Ti6Al4V into the semi-solid state.

Protective link for superconducting coil

DOEpatents

Umans, Stephen D [Belmont, MA

2009-12-08

A superconducting coil system includes a superconducting coil and a protective link of superconducting material coupled to the superconducting coil. A rotating machine includes first and second coils and a protective link of superconducting material. The second coil is operable to rotate with respect to the first coil. One of the first and second coils is a superconducting coil. The protective link is coupled to the superconducting coil.

Disturbance of visual search by stimulating to posterior parietal cortex in the brain using transcranial magnetic stimulation

NASA Astrophysics Data System (ADS)

Iramina, Keiji; Ge, Sheng; Hyodo, Akira; Hayami, Takehito; Ueno, Shoogo

2009-04-01

In this study, we applied a transcranial magnetic stimulation (TMS) to investigate the temporal aspect for the functional processing of visual attention. Although it has been known that right posterior parietal cortex (PPC) in the brain has a role in certain visual search tasks, there is little knowledge about the temporal aspect of this area. Three visual search tasks that have different difficulties of task execution individually were carried out. These three visual search tasks are the "easy feature task," the "hard feature task," and the "conjunction task." To investigate the temporal aspect of the PPC involved in the visual search, we applied various stimulus onset asynchronies (SOAs) and measured the reaction time of the visual search. The magnetic stimulation was applied on the right PPC or the left PPC by the figure-eight coil. The results show that the reaction times of the hard feature task are longer than those of the easy feature task. When SOA=150 ms, compared with no-TMS condition, there was a significant increase in target-present reaction time when TMS pulses were applied. We considered that the right PPC was involved in the visual search at about SOA=150 ms after visual stimulus presentation. The magnetic stimulation to the right PPC disturbed the processing of the visual search. However, the magnetic stimulation to the left PPC gives no effect on the processing of the visual search.

Lung cancer pathogenesis associated with wood smoke exposure.

PubMed

Delgado, Javier; Martinez, Luis M; Sánchez, Therasa T; Ramirez, Alejandra; Iturria, Cecilia; González-Avila, Georgina

2005-07-01

Tobacco is considered the most important cause of lung cancer, but other factors could also be involved in its pathogenesis. The aim of the present work was to establish an association between wood smoke exposure and lung cancer pathogenesis, and to analyze the effects of wood smoke on p53 and murine double minute 2 (MDM2) protein expression. Blood samples were obtained from 62 lung cancer patients, 9 COPD patients, and 9 control subjects. Of the 62 lung cancer patients, 23 were tobacco smokers (lung cancer associated with tobacco [LCT] group), 24 were exposed to wood smoke (lung cancer associated with wood smoke [LCW] group), and 15 could not be included in these groups. Western blot assays were performed to identify the presence of p53, phospho-p53, and murine double minute 2 (MDM2) isoforms in plasma samples. Densitometric analysis was used to determine the intensity of p53, phospho-p53, and MDM2 bands. Approximately 38.7% of the lung cancer patients examined had an association with wood smoke exposure, most of them women living in rural areas. Adenocarcinoma was present in 46.7% of these patients. The p53 and phospho-p53 proteins were significantly increased in LCW samples (56,536.8 +/- 4,629 densitometry units [DU] and 58,244.8 +/- 7,492 DU, respectively [+/- SD]), in comparison with the other groups. The 57-kD MDM2 isoform plasma concentration was very high in LCW and LCT samples (75,696.4 +/- 11,979 DU and 78,551.7 +/- 11,548 DU, respectively). MDM2-p53 complexes were present in a high concentration in control and COPD subjects. This allows p53 degradation and explains the low concentrations of p53 found in these groups. MDM2-phospho-p53 complexes were observed in COPD but not in the other samples. This correlates with the low concentration of p53 observed in the COPD group (13,657 +/- 2,012 DU), and could explain the different clinic evolution of this smoker population in comparison with the LCT subjects. This study suggests that there is a possible association of lung cancer with wood smoke exposure. Likewise, our findings demonstrate that wood smoke could produce similar effects on p53, phospho-p53, and MDM2 protein expression as tobacco.

Safety evaluation of a medium- and long-chain triacylglycerol oil produced from medium-chain triacylglycerols and edible vegetable oil.

PubMed

Matulka, R A; Noguchi, O; Nosaka, N

2006-09-01

To reduce the incorporation of dietary lipids into adipose tissue, modified fats and oils have been developed, such as medium-chain triacylglycerols (MCT). Typical dietary lipids from vegetable oils, termed long-chain triacylglycerols (LCT), are degraded by salivary, intestinal and pancreatic lipases into two fatty acids and a monoacyl glycerol; whereas, MCT are degraded by the same enzymes into three fatty acids and the simple glycerol backbone. Medium-chain fatty acids (MCFA) are readily absorbed from the small intestine directly into the bloodstream and transported to the liver for hepatic metabolism, while long-chain fatty acids (LCFA) are incorporated into chylomicrons and enter the lymphatic system. MCFA are readily broken down to carbon dioxide and two-carbon fragments, while LCFA are re-esterified to triacylglycerols and either metabolized for energy or stored in adipose tissue. Therefore, consumption of MCT decreases the incorporation of fatty acids into adipose tissue. However, MCT have technological disadvantages precluding their use in many food applications. A possible resolution is the manufacture and use of a triacylglycerol containing both LCT and MCT, termed medium- and long-chain triacylglycerol (MLCT). This manuscript describes studies performed for the safety evaluation of a MLCT oil enzymatically produced from MCT and edible vegetable oil (containing LCT), by a transesterification process. The approximate fatty acid composition of this MLCT consists of caprylic acid (9.7%), capric acid (3.3%), palmitic acid (3.8%), stearic acid (1.7%), oleic acid (51.2%), linoleic acid (18.4%), linolenic acid (9.0%), and other fatty acids (2.9%). The approximate percentages of long (L) and medium (M) fatty acids in the triacylglyerols are as follows: L, L, L (55.1%), L, L, M (35.2%), L, M, M (9.1%), and M, M, M (0.6%). The studies included: (1) acute study in rats (LD50>5000 mg/kg); (2) 6 week repeat-dose safety study via dietary administration to rats (NOAEL of 3500 mg/kg/day), (3) in vitro genotoxicity studies using Salmonella typhimurium and Escherichia coli (negative at 5000 mg/plate), and (4) a four-week, placebo-controlled, double blind, human clinical trial utilizing 20 test subjects (no effects at 42 g MLCT/day). These data are corroborated by other studies published in the peer-reviewed literature on analogous MLCTs.

Genome-wide association meta-analysis of circulating odd-numbered chain saturated fatty acids: Results from the CHARGE Consortium

PubMed Central

King, Irena B.; Wu, Jason H. Y.; Manichaikul, Ani; Rich, Stephen S.; Tsai, Michael Y.; Chen, Y. D.; Fornage, Myriam; Weihua, Guan; Aslibekyan, Stella; Irvin, Marguerite R.; Kabagambe, Edmond K.; Arnett, Donna K.; Jensen, Majken K.; McKnight, Barbara; Psaty, Bruce M.; Steffen, Lyn M.; Smith, Caren E.; Risérus, Ulf; Lind, Lars; Hu, Frank B.; Rimm, Eric B.; Siscovick, David S.; Mozaffarian, Dariush

2018-01-01

Background Odd-numbered chain saturated fatty acids (OCSFA) have been associated with potential health benefits. Although some OCSFA (e.g., C15:0 and C17:0) are found in meats and dairy products, sources and metabolism of C19:0 and C23:0 are relatively unknown, and the influence of non-dietary determinants, including genetic factors, on circulating levels of OCSFA is not established. Objective To elucidate the biological processes that influence circulating levels of OCSFA by investigating associations between genetic variation and OCSFA. Design We performed a meta-analysis of genome-wide association studies (GWAS) of plasma phospholipid/erythrocyte levels of C15:0, C17:0, C19:0, and C23:0 among 11,494 individuals of European descent. We also investigated relationships between specific single nucleotide polymorphisms (SNPs) in the lactase (LCT) gene, associated with adult-onset lactase intolerance, with circulating levels of dairy-derived OCSFA, and evaluated associations of candidate sphingolipid genes with C23:0 levels. Results We found no genome-wide significant evidence that common genetic variation is associated with circulating levels of C15:0 or C23:0. In two cohorts with available data, we identified one intronic SNP (rs13361131) in myosin X gene (MYO10) associated with C17:0 level (P = 1.37×10−8), and two intronic SNP (rs12874278 and rs17363566) in deleted in lymphocytic leukemia 1 (DLEU1) region associated with C19:0 level (P = 7.07×10−9). In contrast, when using a candidate-gene approach, we found evidence that three SNPs in LCT (rs11884924, rs16832067, and rs3816088) are associated with circulating C17:0 level (adjusted P = 4×10−2). In addition, nine SNPs in the ceramide synthase 4 (CERS4) region were associated with circulating C23:0 levels (adjusted P<5×10−2). Conclusions Our findings suggest that circulating levels of OCSFA may be predominantly influenced by non-genetic factors. SNPs associated with C17:0 level in the LCT gene may reflect genetic influence in dairy consumption or in metabolism of dairy foods. SNPs associated with C23:0 may reflect a role of genetic factors in the synthesis of sphingomyelin. PMID:29738550

Magnetic field transfer device and method

DOEpatents

Wipf, S.L.

1990-02-13

A magnetic field transfer device includes a pair of oppositely wound inner coils which each include at least one winding around an inner coil axis, and an outer coil which includes at least one winding around an outer coil axis. The windings may be formed of superconductors. The axes of the two inner coils are parallel and laterally spaced from each other so that the inner coils are positioned in side-by-side relation. The outer coil is outwardly positioned from the inner coils and rotatable relative to the inner coils about a rotational axis substantially perpendicular to the inner coil axes to generate a hypothetical surface which substantially encloses the inner coils. The outer coil rotates relative to the inner coils between a first position in which the outer coil axis is substantially parallel to the inner coil axes and the outer coil augments the magnetic field formed in one of the inner coils, and a second position 180[degree] from the first position, in which the augmented magnetic field is transferred into the other inner coil and reoriented 180[degree] from the original magnetic field. The magnetic field transfer device allows a magnetic field to be transferred between volumes with negligible work being required to rotate the outer coil with respect to the inner coils. 16 figs.

Magnetic field transfer device and method

DOEpatents

Wipf, Stefan L.

1990-01-01

A magnetic field transfer device includes a pair of oppositely wound inner coils which each include at least one winding around an inner coil axis, and an outer coil which includes at least one winding around an outer coil axis. The windings may be formed of superconductors. The axes of the two inner coils are parallel and laterally spaced from each other so that the inner coils are positioned in side-by-side relation. The outer coil is outwardly positioned from the inner coils and rotatable relative to the inner coils about a rotational axis substantially perpendicular to the inner coil axes to generate a hypothetical surface which substantially encloses the inner coils. The outer coil rotates relative to the inner coils between a first position in which the outer coil axis is substantially parallel to the inner coil axes and the outer coil augments the magnetic field formed in one of the inner coils, and a second position 180.degree. from the first position, in which the augmented magnetic field is transferred into the other inner coil and reoriented 180.degree. from the original magnetic field. The magnetic field transfer device allows a magnetic field to be transferred between volumes with negligible work being required to rotate the outer coil with respect to the inner coils.

Conformational switching in the coiled-coil domains of a proteasomal ATPase regulates substrate processing.

PubMed

Snoberger, Aaron; Brettrager, Evan J; Smith, David M

2018-06-18

Protein degradation in all domains of life requires ATPases that unfold and inject proteins into compartmentalized proteolytic chambers. Proteasomal ATPases in eukaryotes and archaea contain poorly understood N-terminally conserved coiled-coil domains. In this study, we engineer disulfide crosslinks in the coiled-coils of the archaeal proteasomal ATPase (PAN) and report that its three identical coiled-coil domains can adopt three different conformations: (1) in-register and zipped, (2) in-register and partially unzipped, and (3) out-of-register. This conformational heterogeneity conflicts with PAN's symmetrical OB-coiled-coil crystal structure but resembles the conformational heterogeneity of the 26S proteasomal ATPases' coiled-coils. Furthermore, we find that one coiled-coil can be conformationally constrained even while unfolding substrates, and conformational changes in two of the coiled-coils regulate PAN switching between resting and active states. This switching functionally mimics similar states proposed for the 26S proteasome from cryo-EM. These findings thus build a mechanistic framework to understand regulation of proteasome activity.

Immune activation by medium-chain triglyceride-containing lipid emulsions is not modulated by n-3 lipids or toll-like receptor 4.

PubMed

Olthof, Evelyn D; Gülich, Alexandra F; Renne, Mike F; Landman, Sija; Joosten, Leo A B; Roelofs, Hennie M J; Wanten, Geert J A

2015-10-01

Saturated medium-chain triglycerides (MCT) as part of the parenteral lipid regimen (50% MCT and 50% long chain triglycerides (LCT)) activate the immune system in vitro. Fish oil (FO)-derived n-3 fatty acids (FA) inhibit saturated FA-induced immune activation via a toll-like receptor (TLR)-4 mediated mechanism. We hypothesized that effects of parenteral MCTs on immune cells involve TLR-4 signaling and that these effects are modulated by n-3 FA that are present in FO. To test this hypothesis we assessed effects of addition of various commercially available mixed parenteral lipid emulsions, n-3 FA and of TLR-4 inhibition on MCT-induced human immune cell activation by evaluation of the expression of leukocyte membrane activation markers and reactive oxygen species (ROS) production. All MCT-containing lipid emulsions activated leukocytes by inducing changes in expression of membrane markers and stimulus induced ROS production, whereas MCT-free lipid emulsions lacked this effect. Moreover, addition of n-3 FA to LCT/MCT did not prevent MCT-induced immune activation. TLR-4 inhibitors did not distinctly modulate MCT-induced changes in immune function. Taken together, these findings suggest that leukocyte activation by parenteral MCTs does not involve TLR-4 signaling and is not modulated by n-3 FA in FO-, but is exerted via different signaling pathways. Copyright © 2015 Elsevier Ltd. All rights reserved.

Post-caldera volcanism: In situ measurement of U-Pb age and oxygen isotope ratio in Pleistocene zircons from Yellowstone caldera

USGS Publications Warehouse

Bindeman, I.N.; Valley, J.W.; Wooden, J.L.; Persing, H.M.

2001-01-01

The Yellowstone Plateau volcanic field, the site of some of the largest known silicic volcanic eruptions, is the present location of NE-migrating hotspot volcanic activity. Most volcanic rocks in the Yellowstone caldera (0.6 Ma), which formed in response to the climactic eruption of 1000 km3 of Lava Creek Tuff (LCT), have unusually low oxygen isotope ratios. Ion microprobe analysis of both U-Pb age and ??18O in zircons from these low-??18O lavas reveals evidence of complex inheritance and remelting. A majority of analyzed zircons from low-??18O lavas erupted inside the Yellowstone caldera have cores that range in age from 2.4 to 0.7 Ma, significantly older than their eruption ages (0.5-0.4 Ma). These ages and the high-??18O cores indicate that these lavas are largely derived from nearly total remelting of normal-??18O Huckleberry Ridge Tuff (HRT) and other pre-LCT volcanic rocks. A post-HRT low-??18O lava shows similar inheritance of HRT-age zircons. The recycling of volcanic rocks by shallow remelting can change the water content and eruptive potential of magma. This newly proposed mechanism of intracaldera volcanism is best studied by combining in situ analysis of oxygen and U-Pb isotope ratios of individual crystals. ?? 2001 Elsevier Science B.V. All rights reserved.

Milk Intake at Midlife and Cognitive Decline over 20 Years. The Atherosclerosis Risk in Communities (ARIC) Study.

PubMed

Petruski-Ivleva, Natalia; Kucharska-Newton, Anna; Palta, Priya; Couper, David; Meyer, Katie; Graff, Misa; Haring, Bernhard; Sharrett, Richey; Heiss, Gerardo

2017-10-17

Background : Faster rates of cognitive decline are likely to result in earlier onset of cognitive impairment and dementia. d-galactose, a derivative of lactose, is used in animal studies to induce neurodegeneration. Milk is the primary source of lactose in the human diet, and its effects on cognitive decline have not been fully evaluated. Objective : Assess the association of milk intake with change in cognitive function over 20 years. Methods : A total of 13,751 participants of the Atherosclerosis Risk in Communities (ARIC) cohort completed a food frequency questionnaire and three neurocognitive evaluations from 1990 through 2013. Two single nucleotide polymorphisms (SNPs) were used to determine lactase persistence (LCT-13910 C/T for Whites and LCT-14010 G/C for Blacks). Mixed-effects models were used to study the association of milk intake with cognitive change. Multiple imputations by chained equations were used to account for attrition. Results : Milk intake greater than 1 glass/day was associated with greater decline in the global z-score over a 20-year period. The difference in decline was 0.10 (95% CI: 0.16, 0.03) z-scores, or an additional 10% decline, relative to the group reporting "almost never" consuming milk. Conclusions : Replication of these results is warranted in diverse populations with greater milk intake and higher variability of lactase persistence genotype.

Milk Intake at Midlife and Cognitive Decline over 20 Years. The Atherosclerosis Risk in Communities (ARIC) Study

PubMed Central

Petruski-Ivleva, Natalia; Kucharska-Newton, Anna; Palta, Priya; Meyer, Katie; Graff, Misa; Haring, Bernhard; Sharrett, Richey; Heiss, Gerardo

2017-01-01

Background: Faster rates of cognitive decline are likely to result in earlier onset of cognitive impairment and dementia. d-galactose, a derivative of lactose, is used in animal studies to induce neurodegeneration. Milk is the primary source of lactose in the human diet, and its effects on cognitive decline have not been fully evaluated. Objective: Assess the association of milk intake with change in cognitive function over 20 years. Methods: A total of 13,751 participants of the Atherosclerosis Risk in Communities (ARIC) cohort completed a food frequency questionnaire and three neurocognitive evaluations from 1990 through 2013. Two single nucleotide polymorphisms (SNPs) were used to determine lactase persistence (LCT-13910 C/T for Whites and LCT-14010 G/C for Blacks). Mixed-effects models were used to study the association of milk intake with cognitive change. Multiple imputations by chained equations were used to account for attrition. Results: Milk intake greater than 1 glass/day was associated with greater decline in the global z-score over a 20-year period. The difference in decline was 0.10 (95% CI: 0.16, 0.03) z-scores, or an additional 10% decline, relative to the group reporting “almost never” consuming milk. Conclusions: Replication of these results is warranted in diverse populations with greater milk intake and higher variability of lactase persistence genotype. PMID:29039795

Measuring The Impact Of Cash Transfers And Behavioral 'Nudges' On Maternity Care In Nairobi, Kenya.

PubMed

Cohen, Jessica; Rothschild, Claire; Golub, Ginger; Omondi, George N; Kruk, Margaret E; McConnell, Margaret

2017-11-01

Many patients in low-income countries express preferences for high-quality health care but often end up with low-quality providers. We conducted a randomized controlled trial with pregnant women in Nairobi, Kenya, to analyze whether cash transfers, enhanced with behavioral "nudges," can help women deliver in facilities that are consistent with their preferences and are of higher quality. We tested two interventions. The first was a labeled cash transfer (LCT), which explained that the cash was to help women deliver where they wanted. The second was a cash transfer that combined labeling and a commitment by the recipient to deliver in a prespecified desired facility as a condition of receiving the final payment (L-CCT). The L-CCT improved patient-perceived quality of interpersonal care but not perceived technical quality of care. It also increased women's likelihood of delivering in facilities that met standards for routine and emergency newborn care but not the likelihood of delivering in facilities that met standards for obstetric care. The LCT had fewer measured benefits. Women preferred facilities with high technical and interpersonal care quality, but these quality measures were often negatively correlated within facilities. Even with cash transfers, many women still used poor-quality facilities. A larger study is warranted to determine whether the L-CCT can improve maternal and newborn outcomes.

Application of graph theory to the statistical thermodynamics of lattice polymers. I. Elements of theory and test for dimers

NASA Astrophysics Data System (ADS)

Brazhnik, Olga D.; Freed, Karl F.

1996-07-01

The lattice cluster theory (LCT) is extended to enable inclusion of longer range correlation contributions to the partition function of lattice model polymers in the athermal limit. A diagrammatic technique represents the expansion of the partition function in powers of the inverse lattice coordination number. Graph theory is applied to sort, classify, and evaluate the numerous diagrams appearing in higher orders. New general theorems are proven that provide a significant reduction in the computational labor required to evaluate the contributions from higher order correlations. The new algorithm efficiently generates the correction to the Flory mean field approximation from as many as eight sterically interacting bonds. While the new results contain the essential ingredients for treating a system of flexible chains with arbitrary lengths and concentrations, the complexity of our new algorithm motivates us to test the theory here for the simplest case of a system of lattice dimers by comparison to the dimer packing entropies from the work of Gaunt. This comparison demonstrates that the eight bond LCT is exact through order φ5 for dimers in one through three dimensions, where φ is the volume fraction of dimers. A subsequent work will use the contracted diagrams, derived and tested here, to treat the packing entropy for a system of flexible N-mers at a volume fraction of φ on hypercubic lattices.

Frequency of adult type-associated lactase persistence LCT-13910C/T genotypes in the Czech/Slav and Czech Roma/Gypsy populations

PubMed Central

Hubácek, Jaroslav A.; Adámková, Věra; Šedová, Lenka; Olišarová, Věra; Adámek, Václav; Tóthová, Valérie

2017-01-01

Abstract Lactase non-persistence (leading to primary lactose intolerance) is a genetically dependent inability to digest lactose in adulthood. As part of the human adaptation to dairying, the human lactase LCT-13910C/T mutation (which propagates adult expression of lactase) developed, spread and participated in the adaptation to dairying. This variant is associated with lactase activity persistence, and its carriers are able to digest lactose. We compared the frequencies of lactase 13910C/T (rs4988235) genotypes in Czechs/Slavs (N = 288) and Czech Gypsies/Roma (N = 300), two ethnically different groups where this polymorphism has not yet been analysed. Allelic frequencies significantly differed between the populations (p < 0.0001). In Czechs/Slavs, the lactase persistence T allele was present in 76% of the individuals, which is in agreement with frequencies among geographically neighbouring populations. In the Czech Gypsy/Roma population, only 27% of the adults were carriers of at least one lactase persistence allele, similar to the Indian population. In agreement with this result, dairy product consumption was reported by 70.5% of Czechs/Slavs and 39.0% of the Czech Gypsy/Roma population. Both in the Czech Gypsy/Roma and in the Czech/Slavs populations, the presence of carriers of the lactase persistence allele was similar in subjects self-reporting the consumption of unfermented/fresh milk, in comparison to the others. PMID:28497837

Frequency of adult type-associated lactase persistence LCT-13910C/T genotypes in the Czech/Slav and Czech Roma/Gypsy populations.

PubMed

Hubácek, Jaroslav A; Adámková, Věra; Šedová, Lenka; Olišarová, Věra; Adámek, Václav; Tóthová, Valérie

2017-01-01

Lactase non-persistence (leading to primary lactose intolerance) is a genetically dependent inability to digest lactose in adulthood. As part of the human adaptation to dairying, the human lactase LCT-13910C/T mutation (which propagates adult expression of lactase) developed, spread and participated in the adaptation to dairying. This variant is associated with lactase activity persistence, and its carriers are able to digest lactose. We compared the frequencies of lactase 13910C/T (rs4988235) genotypes in Czechs/Slavs (N = 288) and Czech Gypsies/Roma (N = 300), two ethnically different groups where this polymorphism has not yet been analysed. Allelic frequencies significantly differed between the populations (p < 0.0001). In Czechs/Slavs, the lactase persistence T allele was present in 76% of the individuals, which is in agreement with frequencies among geographically neighbouring populations. In the Czech Gypsy/Roma population, only 27% of the adults were carriers of at least one lactase persistence allele, similar to the Indian population. In agreement with this result, dairy product consumption was reported by 70.5% of Czechs/Slavs and 39.0% of the Czech Gypsy/Roma population. Both in the Czech Gypsy/Roma and in the Czech/Slavs populations, the presence of carriers of the lactase persistence allele was similar in subjects self-reporting the consumption of unfermented/fresh milk, in comparison to the others.

Lactase persistence genotyping on whole blood by loop-mediated isothermal amplification and melting curve analysis.

PubMed

Abildgaard, Anders; Tovbjerg, Sara K; Giltay, Axel; Detemmerman, Liselot; Nissen, Peter H

2018-03-26

The lactase persistence phenotype is controlled by a regulatory enhancer region upstream of the Lactase (LCT) gene. In northern Europe, specifically the -13910C > T variant has been associated with lactase persistence whereas other persistence variants, e.g. -13907C > G and -13915 T > G, have been identified in Africa and the Middle East. The aim of the present study was to compare a previously developed high resolution melting assay (HRM) with a novel method based on loop-mediated isothermal amplification and melting curve analysis (LAMP-MC) with both whole blood and DNA as input material. To evaluate the LAMP-MC method, we used 100 whole blood samples and 93 DNA samples in a two tiered study. First, we studied the ability of the LAMP-MC method to produce specific melting curves for several variants of the LCT enhancer region. Next, we performed a blinded comparison between the LAMP-MC method and our existing HRM method with clinical samples of unknown genotype. The LAMP-MC method produced specific melting curves for the variants at position -13909, -13910, -13913 whereas the -13907C > G and -13915 T > G variants produced indistinguishable melting profiles. The LAMP-MC assay is a simple method for lactase persistence genotyping and compares well with our existing HRM method. Copyright © 2018. Published by Elsevier B.V.

Molecular basis of coiled-coil oligomerization-state specificity.

PubMed

Ciani, Barbara; Bjelic, Saša; Honnappa, Srinivas; Jawhari, Hatim; Jaussi, Rolf; Payapilly, Aishwarya; Jowitt, Thomas; Steinmetz, Michel O; Kammerer, Richard A

2010-11-16

Coiled coils are extensively and successfully used nowadays to rationally design multistranded structures for applications, including basic research, biotechnology, nanotechnology, materials science, and medicine. The wide range of applications as well as the important functions these structures play in almost all biological processes highlight the need for a detailed understanding of the factors that control coiled-coil folding and oligomerization. Here, we address the important and unresolved question why the presence of particular oligomerization-state determinants within a coiled coil does frequently not correlate with its topology. We found an unexpected, general link between coiled-coil oligomerization-state specificity and trigger sequences, elements that are indispensable for coiled-coil formation. By using the archetype coiled-coil domain of the yeast transcriptional activator GCN4 as a model system, we show that well-established trimer-specific oligomerization-state determinants switch the peptide's topology from a dimer to a trimer only when inserted into the trigger sequence. We successfully confirmed our results in two other, unrelated coiled-coil dimers, ATF1 and cortexillin-1. We furthermore show that multiple topology determinants can coexist in the same trigger sequence, revealing a delicate balance of the resulting oligomerization state by position-dependent forces. Our experimental results should significantly improve the prediction of the oligomerization state of coiled coils. They therefore should have major implications for the rational design of coiled coils and consequently many applications using these popular oligomerization domains.

A new type of coil structure called pan-shaped coil of wireless charging system based on magnetic resonance

NASA Astrophysics Data System (ADS)

Yue, Z. K.; Liu, Z. Z.; Hou, Y. J.; Zeng, H.; Liang, L. H.; Cui, S.

2017-11-01

The problem that misalignment between the transmitting coil and the receiving coil significantly impairs the transmission power and efficiency of the system has been attached more and more attention. In order to improve the uniformity of the magnetic field between the two coils to solve this problem, a new type of coil called pan-shaped coil is proposed. Three-dimension simulation models of the planar-core coil and the pan-shaped coil are established using Ansoft Maxwell software. The coupling coefficient between the transmitting coil and the receiving coil is obtained by simulating the magnetic field with the receiving coil misalignment or not. And the maximum percentage difference strength along the radial direction which is defined as the magnetic field uniformity factor is calculated. According to the simulation results of the two kinds of coil structures, it is found that the new type of coil structure can obviously improve the uniformity of the magnetic field, coupling coefficient and power transmission properties between the transmitting coil and the receiving coil.

Improvement of wireless power transmission efficiency of implantable subcutaneous devices by closed magnetic circuit mechanism.

PubMed

Jo, Sung-Eun; Joung, Sanghoon; Suh, Jun-Kyo Francis; Kim, Yong-Jun

2012-09-01

Induction coils were fabricated based on flexible printed circuit board for inductive transcutaneous power transmission. The coil had closed magnetic circuit (CMC) structure consisting of inner and outer magnetic core. The power transmission efficiency of the fabricated device was measured in the air and in vivo condition. It was confirmed that the CMC coil had higher transmission efficiency than typical air-core coil. The power transmission efficiency during a misalignment between primary coil and implanted secondary coil was also evaluated. The decrease of mutual inductance between the two coils caused by the misalignment led to a low efficiency of the inductive link. Therefore, it is important to properly align the primary coil and implanted secondary coil for effective power transmission. To align the coils, a feedback coil was proposed. This was integrated on the backside of the primary coil and enabled the detection of a misalignment of the primary and secondary coils. As a result of using the feedback coil, the primary and secondary coils could be aligned without knowledge of the position of the implanted secondary coil.

The structure of the GemC1 coiled coil and its interaction with the Geminin family of coiled-coil proteins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caillat, Christophe; Fish, Alexander; Pefani, Dafni-Eleftheria

The GemC1 coiled-coil structure has subtle differences compared with its homologues Geminin and Idas. Co-expression experiments in cells and biophysical stability analysis of the Geminin-family coiled coils suggest that the GemC1 coiled coil alone is unstable. GemC1, together with Idas and Geminin, an important regulator of DNA-replication licensing and differentiation decisions, constitute a superfamily sharing a homologous central coiled-coil domain. To better understand this family of proteins, the crystal structure of a GemC1 coiled-coil domain variant engineered for better solubility was determined to 2.2 Å resolution. GemC1 shows a less typical coiled coil compared with the Geminin homodimer and themore » Geminin–Idas heterodimer structures. It is also shown that both in vitro and in cells GemC1 interacts with Geminin through its coiled-coil domain, forming a heterodimer that is more stable that the GemC1 homodimer. Comparative analysis of the thermal stability of all of the possible superfamily complexes, using circular dichroism to follow the unfolding of the entire helix of the coiled coil, or intrinsic tryptophan fluorescence of a unique conserved N-terminal tryptophan, shows that the unfolding of the coiled coil is likely to take place from the C-terminus towards the N-terminus. It is also shown that homodimers show a single-state unfolding, while heterodimers show a two-state unfolding, suggesting that the dimer first falls apart and the helices then unfold according to the stability of each protein. The findings argue that Geminin-family members form homodimers and heterodimers between them, and this ability is likely to be important for modulating their function in cycling and differentiating cells.« less

A periodic table of coiled-coil protein structures.

PubMed

Moutevelis, Efrosini; Woolfson, Derek N

2009-01-23

Coiled coils are protein structure domains with two or more alpha-helices packed together via interlacing of side chains known as knob-into-hole packing. We analysed and classified a large set of coiled-coil structures using a combination of automated and manual methods. This led to a systematic classification that we termed a "periodic table of coiled coils," which we have made available at http://coiledcoils.chm.bris.ac.uk/ccplus/search/periodic_table. In this table, coiled-coil assemblies are arranged in columns with increasing numbers of alpha-helices and in rows of increased complexity. The table provides a framework for understanding possibilities in and limits on coiled-coil structures and a basis for future prediction, engineering and design studies.

[High-risk HPV genotyping PCR testing as a means of cervical cancer and precancerous lesions early screening].

PubMed

Ma, Li; Cong, Xiao; Bian, Meilu; Shi, Mai; Wang, Xiuhong; Liu, Jun; Liu, Haiyan

2015-04-01

To explored high-risk HPV genotyping PCR testing whether as a feasible means for the early screening of cervical cancer and precancerous lesions. From January 2013 to June 2014, 15,192 outpatients in China-Japan Friendship Hospital voluntary were tested by high-risk type HPV genotyping PCR. The average age of them were (33±8) years old. High-risk HPV types genotyping PCR tested by fluorescence PCR technology, in which 13 kinds of high-risk HPV subtypes were detected, including HPV16, 18, 31, 33, 35, 39, 45, 51, 52, 56, 58, 59 and 68. A total of 4,315 cases of them were tested by the liquid-based cytology (LCT), among them with positive of high-risk HPV genotyping tested by PCR (n=2,366) were biopsy under colposcope (648 cases) in those LCT results were positive or LCT negative but HPV16 positive or LCT negative but had the clear clinical symptoms or and non-HPV16 positive but with clear clinical symptoms. (1) Analysis high-risk HPV infection status of 15 192 women. (2) As the pathological diagnosis was the gold standard in the diagnosis of cervical lesions, analysis of the relationship among high-risk HPV infection, virus loads and cervical lesions. (3) To evaluated the value of high-risk HPV genotyping PCR tested method in screening of cervical cancer and precancerous lesions. ⑴ Of 15,192 cases tested by high-risk HPV genotyping PCR, 2,366 cases were HPV positive (HPV infection), the overall infection rate was 15.57% (2,366/15,192), in which a single subtype of HPV infection in 1,767 cases, infection rate was 11.63% (1,767/15,192), and multiple subtypes of HPV infection (two and more subtypes HPV infection) in 599 cases, infection rate was 3.94% (599/15,192). The HPV16, 52 and 58 infections were the most common HPV subtypes in 13 subtypes, the infection rate was 3.95% (600/15,192), 2.86% (435/15,192) and 2.67% (406/15,192), respectively. (2) The most relevant subtypes with cervical intraepithelial neoplasia (CIN) II and even higher lesion were HPV16, 52 and 58, accounted for 57.7% (154/267) of all above CIN II lesions. The most relevant subtype with the cervical glandular intraepithelial neoplasia (CGIN) II or above lesions was HPV18, 3 cases with CGIN II or above lesions were all single HPV18 infection. The pathologic examination positive percentage of patients which HPV virus loads≤10(3) copys/10(4) cells was 18.2% (25/137), while the pathologic examination positive proportion was 33.3% (247/742) which HPV virus loads≥10(4) copys/10(4) cells, there was statistically significant difference between them (χ2=27.06, P=0.000). (3) Sensitivity, specificity, positive predictive value and negative predictive value for detection of CIN II or above using HPV genotyping PCR were 96.11%, 85.76%, 30.94% and 99.70%, respectively. There were a guiding significance for high-risk HPV genotyping PCR tested in screening of cervical cancer and precancerous lesion. HPV16, 52 and 58 were related to the severe cervical squamous epithelial lesions, while HPV18 was related to cervical severe glandular cell pathological changes. HPV genotyping is feasible and economical as the first choice of opportunistic screening in tertiary hospitals.

An ion microprobe study of individual zircon phenocrysts from voluminous post-caldera rhyolites of the Yellowstone caldera

NASA Astrophysics Data System (ADS)

Watts, K. E.; Bindeman, I. N.; Schmitt, A. K.

2010-12-01

Following the formation of the Yellowstone caldera from the 640 ka supereruption of the Lava Creek Tuff (LCT), a voluminous episode of post-caldera volcanism filled the caldera with >600 km3 of low-δ18O rhyolite. Such low-δ18O signatures require remelting of 100s of km3 of hydrothermally altered (18O-depleted) rock in the shallow crust. We present a high resolution oxygen isotope and geochronology (U-Th and U-Pb) study of individual zircon crystals from seven of these voluminous post-caldera rhyolites in order to elucidate their genesis. Oxygen isotope and geochronology analyses of zircon were performed with an ion microprobe that enabled us to doubly fingerprint 25-30 µm diameter spots. Host groundmass glasses and coexisting quartz were analyzed in bulk for oxygen isotopes by laser fluorination. We find that zircons from the youngest (200-80 ka) post-caldera rhyolites have oxygen isotopic compositions that are in equilibrium with low-δ18O host groundmass glasses and quartz and are unzoned in oxygen and U-Th age. This finding is in contrast to prior work on older (500-250 ka) post-caldera rhyolites, which exhibit isotopic disequilibria and age zoning, including the presence of clearly inherited zircon cores. Average U-Th crystallization ages and δ18O zircon values for Pitchstone Plateau flow (81±7 ka, 2.8±0.2‰), West Yellowstone flow (118±8 ka, 2.8±0.1‰), Elephant Back flow (175±22 ka, 2.7±0.2‰) and Tuff of Bluff Point (176±20 ka, 2.7±0.1‰) are overlapping or nearly overlapping in age and identical in oxygen isotope composition within uncertainty (2 SE). New U-Pb geochronology and oxygen isotope data for the North Biscuit Basin flow establish that it has an age (188±33 ka) and δ18O signature (2.8±0.2‰) that is distinctive of the youngest post-caldera rhyolites. Conversely, the South Biscuit Basin flow has a heterogeneous zircon population with ages that range from 550-250 ka. In this unit, older and larger (200-400 µm) zircons have more disparity in δ18O signatures (-0.2-3.6‰) while the younger and smaller (<100-200 µm) zircons have δ18O signatures (2.6±0.3‰) that are identical to the youngest post-caldera rhyolites. Our results are consistent with derivation of the youngest post-caldera rhyolites from a common magma reservoir that was assembled from heterogeneous pockets of low-δ18O melt. The magma was homogenized prior to eruption, erasing evidence of batch assembly in all but the oldest South Biscuit Basin unit. An important new finding of this study is that the newly defined post-LCT East Biscuit Basin flow is the oldest (U-Pb age of 761±66 ka) and most primitive (70 wt% SiO2) rhyolite to erupt from within the Yellowstone caldera. Unlike the youngest post-caldera rhyolites, the average δ18O composition of East Biscuit Basin zircons (4.4±0.3‰) is significantly higher and out of equilibrium with the host groundmass glass (δ18O=1.0‰). Its formation requires remelting of hydrothermally altered LCT and pre-LCT subcaldera rocks that retain oxygen isotopic evidence of inherited zircon phenocrysts.

Four signature motifs define the first class of structurally related large coiled-coil proteins in plants.

PubMed Central

Gindullis, Frank; Rose, Annkatrin; Patel, Shalaka; Meier, Iris

2002-01-01

Background Animal and yeast proteins containing long coiled-coil domains are involved in attaching other proteins to the large, solid-state components of the cell. One subgroup of long coiled-coil proteins are the nuclear lamins, which are involved in attaching chromatin to the nuclear envelope and have recently been implicated in inherited human diseases. In contrast to other eukaryotes, long coiled-coil proteins have been barely investigated in plants. Results We have searched the completed Arabidopsis genome and have identified a family of structurally related long coiled-coil proteins. Filament-like plant proteins (FPP) were identified by sequence similarity to a tomato cDNA that encodes a coiled-coil protein which interacts with the nuclear envelope-associated protein, MAF1. The FPP family is defined by four novel unique sequence motifs and by two clusters of long coiled-coil domains separated by a non-coiled-coil linker. All family members are expressed in a variety of Arabidopsis tissues. A homolog sharing the structural features was identified in the monocot rice, indicating conservation among angiosperms. Conclusion Except for myosins, this is the first characterization of a family of long coiled-coil proteins in plants. The tomato homolog of the FPP family binds in a yeast two-hybrid assay to a nuclear envelope-associated protein. This might suggest that FPP family members function in nuclear envelope biology. Because the full Arabidopsis genome does not appear to contain genes for lamins, it is of interest to investigate other long coiled-coil proteins, which might functionally replace lamins in the plant kingdom. PMID:11972898

A new twist in the coil: functions of the coiled-coil domain of structural maintenance of chromosome (SMC) proteins.

PubMed

Matityahu, Avi; Onn, Itay

2018-02-01

The higher-order organization of chromosomes ensures their stability and functionality. However, the molecular mechanism by which higher order structure is established is poorly understood. Dissecting the activity of the relevant proteins provides information essential for achieving a comprehensive understanding of chromosome structure. Proteins of the structural maintenance of chromosome (SMC) family of ATPases are the core of evolutionary conserved complexes. SMC complexes are involved in regulating genome dynamics and in maintaining genome stability. The structure of all SMC proteins resembles an elongated rod that contains a central coiled-coil domain, a common protein structural motif in which two α-helices twist together. In recent years, the imperative role of the coiled-coil domain to SMC protein activity and regulation has become evident. Here, we discuss recent advances in the function of the SMC coiled coils. We describe the structure of the coiled-coil domain of SMC proteins, modifications and interactions that are mediated by it. Furthermore, we assess the role of the coiled-coil domain in conformational switches of SMC proteins, and in determining the architecture of the SMC dimer. Finally, we review the interplay between mutations in the coiled-coil domain and human disorders. We suggest that distinctive properties of coiled coils of different SMC proteins contribute to their distinct functions. The discussion clarifies the mechanisms underlying the activity of SMC proteins, and advocates future studies to elucidate the function of the SMC coiled coil domain.

RF Magnetic Field Uniformity of Rectangular Planar Coils for Resonance Imaging

DTIC Science & Technology

2016-02-04

coil with square -shaped overlapping turns along the 135mm length of the coil. This paper compares these two coils to determine which has a more...in which, the coil arrays consist of a few square or circular coils side-by-side or overlapping. Mobile unilateral NMR/MRI scanners were...magnetic field along the length of a normal rectangular coil (NRC) and a rectangular coil with overlapping square -shaped turns (RCOS). The RCOS coil is

Experimental measurement of coil-rod-coil block copolymer tracer diffusion through entangled coil homopolymers

PubMed Central

Wang, Muzhou; Timachova, Ksenia; Olsen, Bradley D.

2014-01-01

The diffusion of coil-rod-coil triblock copolymers in entangled coil homopolymers is experimentally measured and demonstrated to be significantly slower than rod or coil homopolymers of the same molecular weight. A model coil-rod-coil triblock was prepared by expressing rodlike alanine-rich α-helical polypeptides in E. coli and conjugating coillike poly(ethylene oxide) (PEO) to both ends to form coil-rod-coil triblock copolymers. Tracer diffusion through entangled PEO homopolymer melts was measured using forced Rayleigh scattering at various rod lengths, coil molecular weights, and coil homopolymer concentrations. For rod lengths, L, that are close to the entanglementh length, a, the ratio between triblock diffusivity and coil homopolymer diffusivity decreases monotonically and is only a function of L/a, in quantitative agreement with previous simulation results. For large rod lengths, diffusion follows an arm retraction scaling, which is also consistent with previous theoretical predictions. These experimental results support the key predictions of theory and simulation, suggesting that the mismatch in curvature between rod and coil entanglement tubes leads to the observed diffusional slowing. PMID:25484454

Magnetic propulsion of a magnetic device using three square-Helmholtz coils and a square-Maxwell coil.

PubMed

Ha, Yong H; Han, Byung H; Lee, Soo Y

2010-02-01

We introduce a square coil system for remote magnetic navigation of a magnetic device without any physical movements of the coils. We used three square-Helmholtz coils and a square-Maxwell coil for magnetic propulsion of a small magnet along the desired path. All the square coils are mountable on a cubic frame that has an opening to accommodate a living subject. The square-Helmholtz coils control the magnetic propulsion direction by generating uniform magnetic field along the desired direction while the square-Maxwell coil controls the propulsion force by generating magnetic gradient field. We performed magnetic propulsion experiments with a down-scaled coil set and a three-channel coil driver. Experimental results demonstrate that we can use the square coil set for magnetic navigation of a magnetic device without any physical movements of the coils.

Electromagnetic calibration system for sub-micronewton torsional thrust stand

NASA Astrophysics Data System (ADS)

Lam, J. K.; Koay, S. C.; Cheah, K. H.

2017-12-01

It is critical for a micropropulsion system to be evaluated. Thrust stands are widely recognised as the instrument to complete such tasks. This paper presents the development of an alternative electromagnetic calibration technique for thrust stands. Utilising the commercially made voice coils and permanent magnets, the proposed system is able to generate repeatable and also consistent steady-state calibration forces at over four orders of magnitude (30 - 23000 μN). The system is then used to calibrate a custom-designed torsional thrust stand, where its inherent ability in ease of setup is well demonstrated.

Study on electromagnetic characteristics of the magnetic coupling resonant coil for the wireless power transmission system.

PubMed

Wang, Zhongxian; Liu, Yiping; Wei, Yonggeng; Song, Yilin

2018-01-01

The resonant coil design is taken as the core technology in the magnetic coupling resonant wireless power transmission system, which achieves energy transmission by the coupling of the resonant coil. This paper studies the effect of the resonant coil on energy transmission and the efficiency of the system. Combining a two-coil with a three-coil system, the optimum design method for the resonant coil is given to propose a novel coil structure. First, the co-simulation methods of Pspice and Maxwell are used. When the coupling coefficient of the resonant coil is different, the relationship between system transmission efficiency, output power, and frequency is analyzed. When the self-inductance of the resonant coil is different, the relationship between the performance and frequency of the system transmission is analyzed. Then, two-coil and three-coil structure models are built, and the parameters of the magnetic field of the coils are calculated and analyzed using the finite element method. In the end, a dual E-type simulation circuit model is used to optimize the design of the novel resonance coil. The co-simulation results show that the coupling coefficients of the two-coil, three-coil, and novel coil systems are 0.017, 0.17 and 0.0126, respectively. The power loss of the novel coil is 16.4 mW. There is an obvious improvement in the three-coil system, which shows that the magnetic leakage of the field and the energy coupling are relatively small. The new structure coil has better performance, and the load loss is lower; it can improve the system output power and transmission efficiency.

Training Materials and Data Requirements for Driver Trainer (DT) training Test Support Plan

DTIC Science & Technology

1980-08-01

KENTUCKY MAR 18 August 1980S LcT I..-..U.S. ARMY RESEARCH INSTITUTE for the BEHAVIORAL and SOCIAL SCIENCES Approved for public release; distribution...LEGIBLY, K U. S. ARMY RESEARCH INS.JLTUTE FOR THE BEHAVIORAL AND SOCIAL SCIENCES A Field Operating Agency under the Jurisdiction of the Deputy Chief of...AND ADDRESS 12. REPORT DATE US Army Research Institute for the Behavioral August 1980 and Social Sciences, 5001 Eisenhower Ave. 13 NUMBER OF PAGES

Band of Brothers or Dysfunctional Family? A Military Perspective on Coalition Challenges During Stability Operations

DTIC Science & Technology

2011-01-01

vehicle LCT landing craft, tank LO liaison officer LOO line of operation MIS Military Intelligence Service MND (SE) Multi-National Division South East...23, 2000. Their units then fell under the command of the peace- keeping force (PKF) commander, Lt Gen Jaime de los Santos of the Philippines, who was...rather than instantaneous transition of responsibility between his command and the PKF. He suggested to General de los Santos that the UNTAET staff

Determination of LCt50s in Anesthetized Rats Exposed to Aerosolized Nerve Agents

DTIC Science & Technology

2013-01-01

anticholinesterases that inhibit the enzyme acetyl-cholinesterase that is necessary for degrad- ing acetylcholine, a critical neurotransmitter active at neuromuscular... activity (Ellman et al. 1961; Doctor et al. 1987). To this, 260 μL of phosphate buffer (pH 8.0) containing 4 μM of iso-OMPA (tetra monoiso- propyl...The plate was read in a SpectraMax Plus384 spectropho- tometer (Molecular Devices, Sunnyvale, CA) at 412 nm. The AChE activity , measured in triplicate

Crystal structure of a super leucine zipper, an extended two-stranded super long coiled coil

PubMed Central

Diao, Jiasheng

2010-01-01

Coiled coil is a ubiquitous structural motif in proteins, with two to seven alpha helices coiled together like the strands of a rope, and coiled coil folding and assembly is not completely understood. A GCN4 leucine zipper mutant with four mutations of K3A, D7A, Y17W, and H18N has been designed, and the crystal structure has been determined at 1.6 Å resolution. The peptide monomer shows a helix trunk with short curved N- and C-termini. In the crystal, two monomers cross in 35° and form an X-shaped dimer, and each X-shaped dimer is welded into the next one through sticky hydrophobic ends, thus forming an extended two-stranded, parallel, super long coiled coil rather than a discrete, two-helix coiled coil of the wild-type GCN4 leucine zipper. Leucine residues appear at every seventh position in the super long coiled coil, suggesting that it is an extended super leucine zipper. Compared to the wild-type leucine zipper, the N-terminus of the mutant has a dramatic conformational change and the C-terminus has one more residue Glu 32 determined. The mutant X-shaped dimer has a large crossing angle of 35° instead of 18° in the wild-type dimer. The results show a novel assembly mode and oligomeric state of coiled coil, and demonstrate that mutations may affect folding and assembly of the overall coiled coil. Analysis of the formation mechanism of the super long coiled coil may help understand and design self-assembling protein fibers. PMID:20027625

Microcoil embolization during abdominal vascular interventions through microcatheters with a tip of 2 French or less.

PubMed

Miyayama, Shiro; Yamashiro, Masashi; Hattori, Yuki; Orito, Nobuaki; Matsui, Ken; Tsuji, Kazunobu; Yoshida, Miki; Matsui, Osamu

2011-05-01

The aim of this study was to evaluate the technical aspects of embolization using microcoils through a microcatheter with a tip of 2F or smaller during abdominal vascular interventions. Coil embolization through a microcatheter with a tip of 2F or smaller was attempted in 73 procedures. Two types of microcoil-Liquid Coil (Boston Scientific, Watertown, MA, USA) and Tornado Coil (Cook, Bloomington, IN, USA)-were deployed through four types of thinner microcatheter [2F tip (n = 49) and 1.8F tip (n = 24)]. Coil jams in the microcatheter and coil migration were evaluated. In total, 286 microcoils were placed (mean ± SD, 3.9 ± 4.3 coils per procedure, range 1-32 coils). In 19 procedures (26.9%), Liquid Coils were used alone. In 44 (60.3%), Tornado Coils were used alone. In 10 (13.7%), Liquid Coils and Tornado Coils were combined. There were no coil jams in the microcatheter in this series. One Tornado Coil (0.3%) delivered into the gastroduodenal artery migrated to the right hepatic artery. Liquid Coils and Tornado Coils can be placed through a thinner microcatheter without difficulty. However, there is a risk of coil migration in large vessels or at the proximal site because the catheter tip is not stabilized.

Quantitative Evaluation of Performance in Interventional Neuroradiology: An Integrated Curriculum Featuring Theoretical and Practical Challenges.

PubMed

Ernst, Marielle; Kriston, Levente; Romero, Javier M; Frölich, Andreas M; Jansen, Olav; Fiehler, Jens; Buhk, Jan-Hendrik

2016-01-01

We sought to develop a standardized curriculum capable of assessing key competencies in Interventional Neuroradiology by the use of models and simulators in an objective, quantitative, and efficient way. In this evaluation we analyzed the associations between the practical experience, theoretical knowledge, and the skills lab performance of interventionalists. We evaluated the endovascular skills of 26 participants of the Advanced Course in Endovascular Interventional Neuroradiology of the European Society of Neuroradiology with a set of three tasks (aneurysm coiling and thrombectomy in a virtual simulator and placement of an intra-aneurysmal flow disruptor in a flow model). Practical experience was assessed by a survey. Participants completed a written and oral examination to evaluate theoretical knowledge. Bivariate and multivariate analyses were performed. In multivariate analysis knowledge of materials and techniques in Interventional Neuroradiology was moderately associated with skills in aneurysm coiling and thrombectomy. Experience in mechanical thrombectomy was moderately associated with thrombectomy skills, while age was negatively associated with thrombectomy skills. We found no significant association between age, sex, or work experience and skills in aneurysm coiling. Our study gives an example of how an integrated curriculum for reasonable and cost-effective assessment of key competences of an interventional neuroradiologist could look. In addition to traditional assessment of theoretical knowledge practical skills are measured by the use of endovascular simulators yielding objective, quantitative, and constructive data for the evaluation of the current performance status of participants as well as the evolution of their technical competency over time.

Unraveling double stranded alpha-helical coiled coils: an x-ray diffraction study on hard alpha-keratin fibers.

PubMed

Kreplak, L; Doucet, J; Briki, F

2001-04-15

Transformations of proteins secondary and tertiary structures are generally studied in globular proteins in solution. In fibrous proteins, such as hard alpha-keratin, that contain long and well-defined double stranded alpha-helical coiled coil domains, such study can be directly done on the native fibrous tissue. In order to assess the structural behavior of the coiled coil domains under an axial mechanical stress, wide angle x-ray scattering and small angle x-ray scattering experiments have been carried out on stretched horse hair fibers at relative humidity around 30%. Our observations of the three major axial spacings as a function of the applied macroscopic strain have shown two rates. Up to 4% macroscopic strain the coiled coils were slightly distorted but retained their overall conformation. Above 4% the proportion of coiled coil domains progressively decreased. The main and new result of our study is the observation of the transition from alpha-helical coiled coils to disordered chains instead of the alpha-helical coiled coil to beta-sheet transition that occurs in wet fibers.

Development of a planar-type high sensitivity metallic contaminant detector

NASA Astrophysics Data System (ADS)

Okabe, Shunsuke; Sasada, Ichiro

2017-05-01

Metallic contaminant detectors based on the balanced coil system are widely used in the food industry. In the balanced coil system, an excitation coil and two identical pickup coils are used in a way that the magnetic coupling of pickup coils to the excitation coil is cancelled with each other when no metallic contaminants present. In a conventional system, the excitation coil and the pickup coil are planar and are parallel, therefore the magnetic coupling is strong even if there is no metallic contaminant. Such strong magnetic coupling makes balancing procedure tedious. In this paper, we introduce a new coil system in which pickup coils are set orthogonal to the excitation coil, making the magnetic coupling much small compared to conventional counterpart. Pickup coils are equipped with thin magnetic cores and placed inside the excitation coil being parallel to the excitation coil plane. The balancing method consists of two steps; the one is geometrical and the other is digital processing including down conversion. Experiments are carried out to show the detection capability of ferromagnetic contaminants and non-magnetic contaminants.

Accommodation of structural rearrangements in the huntingtin-interacting protein 1 coiled-coil domain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilbur, Jeremy D., E-mail: jwilbur@msg.ucsf.edu; Hwang, Peter K.; Brodsky, Frances M.

2010-03-01

Variable packing interaction related to the conformational flexibility within the huntingtin-interacting protein 1 coiled coil domain. Huntingtin-interacting protein 1 (HIP1) is an important link between the actin cytoskeleton and clathrin-mediated endocytosis machinery. HIP1 has also been implicated in the pathogenesis of Huntington’s disease. The binding of HIP1 to actin is regulated through an interaction with clathrin light chain. Clathrin light chain binds to a flexible coiled-coil domain in HIP1 and induces a compact state that is refractory to actin binding. To understand the mechanism of this conformational regulation, a high-resolution crystal structure of a stable fragment from the HIP1 coiled-coilmore » domain was determined. The flexibility of the HIP1 coiled-coil region was evident from its variation from a previously determined structure of a similar region. A hydrogen-bond network and changes in coiled-coil monomer interaction suggest that the HIP1 coiled-coil domain is uniquely suited to allow conformational flexibility.« less

Accommodation of structural rearrangements in the huntingtin-interacting protein 1 coiled-coil domain.

PubMed

Wilbur, Jeremy D; Hwang, Peter K; Brodsky, Frances M; Fletterick, Robert J

2010-03-01

Huntingtin-interacting protein 1 (HIP1) is an important link between the actin cytoskeleton and clathrin-mediated endocytosis machinery. HIP1 has also been implicated in the pathogenesis of Huntington's disease. The binding of HIP1 to actin is regulated through an interaction with clathrin light chain. Clathrin light chain binds to a flexible coiled-coil domain in HIP1 and induces a compact state that is refractory to actin binding. To understand the mechanism of this conformational regulation, a high-resolution crystal structure of a stable fragment from the HIP1 coiled-coil domain was determined. The flexibility of the HIP1 coiled-coil region was evident from its variation from a previously determined structure of a similar region. A hydrogen-bond network and changes in coiled-coil monomer interaction suggest that the HIP1 coiled-coil domain is uniquely suited to allow conformational flexibility.

Crystal Structure of a Super Leucine Zipper an Extended Two-Stranded Super Long Coiled Coil

DOE Office of Scientific and Technical Information (OSTI.GOV)

J Diao

2011-12-31

Coiled coil is a ubiquitous structural motif in proteins, with two to seven alpha helices coiled together like the strands of a rope, and coiled coil folding and assembly is not completely understood. A GCN4 leucine zipper mutant with four mutations of K3A, D7A, Y17W, and H18N has been designed, and the crystal structure has been determined at 1.6 {angstrom} resolution. The peptide monomer shows a helix trunk with short curved N- and C-termini. In the crystal, two monomers cross in 35{sup o} and form an X-shaped dimer, and each X-shaped dimer is welded into the next one through stickymore » hydrophobic ends, thus forming an extended two-stranded, parallel, super long coiled coil rather than a discrete, two-helix coiled coil of the wild-type GCN4 leucine zipper. Leucine residues appear at every seventh position in the super long coiled coil, suggesting that it is an extended super leucine zipper. Compared to the wild-type leucine zipper, the N-terminus of the mutant has a dramatic conformational change and the C-terminus has one more residue Glu 32 determined. The mutant X-shaped dimer has a large crossing angle of 35{sup o} instead of 18{sup o} in the wild-type dimer. The results show a novel assembly mode and oligomeric state of coiled coil, and demonstrate that mutations may affect folding and assembly of the overall coiled coil. Analysis of the formation mechanism of the super long coiled coil may help understand and design self-assembling protein fibers.« less

System and method for cancelling the effects of stray magnetic fields from the output of a variable reluctance sensor

DOEpatents

Chen, Chingchi; Degner, Michael W.

2002-11-19

A sensor system for sensing a rotation of a sensing wheel is disclosed. The sensor system has a sensing coil in juxtaposition with the sensing wheel. Moreover, the sensing coil has a sensing coil output signal indicative of the rotational speed of the sensing wheel. Further, a cancellation coil is located remotely from the sensing coil and connected in series therewith. Additionally, the cancellation coil has a cancellation coil output signal indicative of an environmental disturbance which is effecting the sensing coil output signal. The cancellation coil output signal operates to cancel the effects of the environmental disturbance on the sensing coil output signal.

Wellbore manufacturing processes for in situ heat treatment processes

DOEpatents

Davidson, Ian Alexander; Geddes, Cameron James; Rudolf, Randall Lynn; Selby, Bruce Allen; MacDonald, Duncan Charles

2012-12-11

A method includes making coiled tubing at a coiled tubing manufacturing unit coupled to a coiled tubing transportation system. One or more coiled tubing reels are transported from the coiled tubing manufacturing unit to one or more moveable well drilling systems using the coiled tubing transportation system. The coiled tubing transportation system runs from the tubing manufacturing unit to one or more movable well drilling systems, and then back to the coiled tubing manufacturing unit.

Aneurysm permeability following coil embolization: packing density and coil distribution

PubMed Central

Chueh, Ju-Yu; Vedantham, Srinivasan; Wakhloo, Ajay K; Carniato, Sarena L; Puri, Ajit S; Bzura, Conrad; Coffin, Spencer; Bogdanov, Alexei A; Gounis, Matthew J

2015-01-01

Background Rates of durable aneurysm occlusion following coil embolization vary widely, and a better understanding of coil mass mechanics is desired. The goal of this study is to evaluate the impact of packing density and coil uniformity on aneurysm permeability. Methods Aneurysm models were coiled using either Guglielmi detachable coils or Target coils. The permeability was assessed by taking the ratio of microspheres passing through the coil mass to those in the working fluid. Aneurysms containing coil masses were sectioned for image analysis to determine surface area fraction and coil uniformity. Results All aneurysms were coiled to a packing density of at least 27%. Packing density, surface area fraction of the dome and neck, and uniformity of the dome were significantly correlated (p<0.05). Hence, multivariate principal components-based partial least squares regression models were used to predict permeability. Similar loading vectors were obtained for packing and uniformity measures. Coil mass permeability was modeled better with the inclusion of packing and uniformity measures of the dome (r2=0.73) than with packing density alone (r2=0.45). The analysis indicates the importance of including a uniformity measure for coil distribution in the dome along with packing measures. Conclusions A densely packed aneurysm with a high degree of coil mass uniformity will reduce permeability. PMID:25031179

Evaluation of a New 1H/31P Dual-Tuned Birdcage Coil for 31P Spectroscopy

PubMed Central

Potter, WM; Wang, L; McCully, KK; Zhao, Q

2013-01-01

We introduce a new dual-tuned Hydrogen/Phosphorus (1H/31P) birdcage coil, referred to as split birdcage coil, and evaluate its performance using both simulations and magnetic resonance (MR) experiments on a 3 T MR scanner. The proposed coil simplifies the practical matters of tuning and matching, which makes the coil easily reproducible. Simulations were run with the Finite Difference in Time Domain (FDTD) method to evaluate the sensitivity and homogeneity of the magnetic field generated by the proposed 1H coils. Following simulations, MR experiments were conducted using both a phantom and human thigh to compare the proposed design with a currently available commercial dual-tuned flexible surface coil, referred to as flex surface coil, for signal to noise ratio (SNR) as well as homogeneity for the 31P coil. At regions deep within the human thigh, the split birdcage coil was able to acquire spectroscopic signal with a higher average SNR than the flex surface coil. For all regions except those close to the flex surface coil, the split birdcage coil matched or exceeded the performance of the flex surface coil. PMID:24039555

Computational study for the effects of coil configuration on blood flow characteristics in coil-embolized cerebral aneurysm.

PubMed

Otani, Tomohiro; Ii, Satoshi; Shigematsu, Tomoyoshi; Fujinaka, Toshiyuki; Hirata, Masayuki; Ozaki, Tomohiko; Wada, Shigeo

2017-05-01

Coil embolization of cerebral aneurysms with inhomogeneous coil distribution leads to an incomplete occlusion of the aneurysm. However, the effects of this factor on the blood flow characteristics are still not fully understood. This study investigates the effects of coil configuration on the blood flow characteristics in a coil-embolized aneurysm using computational fluid dynamics (CFD) simulation. The blood flow analysis in the aneurysm with coil embolization was performed using a coil deployment (CD) model, in which the coil configuration was constructed using a physics-based simulation of the CD. In the CFD results, total flow momentum and kinetic energy in the aneurysm gradually decayed with increasing coil packing density (PD), regardless of the coil configuration attributed to deployment conditions. However, the total shear rate in the aneurysm was relatively high and the strength of the local shear flow varied based on the differences in coil configuration, even at adequate PDs used in clinical practice (20-25 %). Because the sufficient shear rate reduction is a well-known factor in the blood clot formation occluding the aneurysm inside, the present study gives useful insight into the effects of coil configuration on the treatment efficiency of coil embolization.

Method and apparatus for magnetic resonance imaging and spectroscopy using microstrip transmission line coils

DOEpatents

Zhang, Xiaoliang; Ugurbil, Kamil; Chen, Wei

2006-04-04

Apparatus and method for MRI imaging using a coil constructed of microstrip transmission line (MTL coil) are disclosed. In one method, a target is positioned to be imaged within the field of a main magnetic field of a magnet resonance imaging (MRI) system, a MTL coil is positioned proximate the target, and a MRI image is obtained using the main magnet and the MTL coil. In another embodiment, the MRI coil is used for spectroscopy. MRI imaging and spectroscopy coils are formed using microstrip transmission line. These MTL coils have the advantageous property of good performance while occupying a relatively small space, thus allowing MTL coils to be used inside restricted areas more easily than some other prior art coils. In addition, the MTL coils are relatively simple to construct of inexpensive components and thus relatively inexpensive compared to other designs. Further, the MTL coils of the present invention can be readily formed in a wide variety of coil configurations, and used in a wide variety of ways. Further, while the MTL coils of the present invention work well at high field strengths and frequencies, they also work at low frequencies and in low field strengths as well.

Apparatus and method for reducing inductive coupling between levitation and drive coils within a magnetic propulsion system

DOEpatents

Post, Richard F.

2001-01-01

An apparatus and method is disclosed for reducing inductive coupling between levitation and drive coils within a magnetic levitation system. A pole array has a magnetic field. A levitation coil is positioned so that in response to motion of the magnetic field of the pole array a current is induced in the levitation coil. A first drive coil having a magnetic field coupled to drive the pole array also has a magnetic flux which induces a parasitic current in the levitation coil. A second drive coil having a magnetic field is positioned to attenuate the parasitic current in the levitation coil by canceling the magnetic flux of the first drive coil which induces the parasitic current. Steps in the method include generating a magnetic field with a pole array for levitating an object; inducing current in a levitation coil in response to motion of the magnetic field of the pole array; generating a magnetic field with a first drive coil for propelling the object; and generating a magnetic field with a second drive coil for attenuating effects of the magnetic field of the first drive coil on the current in the levitation coil.

Characteristics of bowl-shaped coils for transcranial magnetic stimulation

NASA Astrophysics Data System (ADS)

Yamamoto, Keita; Suyama, Momoko; Takiyama, Yoshihiro; Kim, Dongmin; Saitoh, Youichi; Sekino, Masaki

2015-05-01

Transcranial magnetic stimulation (TMS) has recently been used as a method for the treatment of neurological and psychiatric diseases. Daily TMS sessions can provide continuous therapeutic effectiveness, and the installation of TMS systems at patients' homes has been proposed. A figure-eight coil, which is normally used for TMS therapy, induces a highly localized electric field; however, it is challenging to achieve accurate coil positioning above the targeted brain area using this coil. In this paper, a bowl-shaped coil for stimulating a localized but wider area of the brain is proposed. The coil's electromagnetic characteristics were analyzed using finite element methods, and the analysis showed that the bowl-shaped coil induced electric fields in a wider area of the brain model than a figure-eight coil. The expanded distribution of the electric field led to greater robustness of the coil to the coil-positioning error. To improve the efficiency of the coil, the relationship between individual coil design parameters and the resulting coil characteristics was numerically analyzed. It was concluded that lengthening the outer spherical radius and narrowing the width of the coil were effective methods for obtaining a more effective and more uniform distribution of the electric field.

Using the integral equations method to model a 2G racetrack coil with anisotropic critical current dependence

NASA Astrophysics Data System (ADS)

Martins, F. G. R.; Sass, F.; Barusco, P.; Ferreira, A. C.; de Andrade, R., Jr.

2017-11-01

Second-generation (2G) superconducting wires have already proved their potential in several applications. These materials have a highly nonlinear behavior that turns an optimized engineering project into a challenge. Between several numerical techniques that can be used to perform this task, the integral equations (IE) method stands out for avoiding mesh problems by representing the 2G wire cross-sectional area by a line. While most applications need to be represented in a 3D geometry, the IE is limited to longitudinal or axisymmetric models. This work demonstrates that a complex 3D geometry can be modeled by several coupled simulations using the IE method. In order to prove this statement, the proposed technique was used to simulate a 2G racetrack coil considering the self-field magnitude (B) and incidence angle (θ) on the tape. The J c characteristic was modeled in terms of parallel and normal to the tape plane magnetic field components (J c(B ∥ , B ⊥)) obtained from a V-I(B, θ) characterization of a tape segment. This result was implemented using commercial software with both A-V (vector magnetic potential and scalar voltage potential) and IE coupled simulations solved by finite elements. This solution bypasses the meshing problem due to the tapes slim geometry, considering each turn a single 1D model, all magnetically interacting in two 2D models. The simulations results are in good agreement to what was both expected and observed in the literature. The simulation is compared to the measured V-I characteristic for a single pancake racetrack coil built with same geometry as its simulation models, and a theoretical study demonstrates the possibilities of the proposed tool for analyzing a racetrack coil current density and electric field behavior in each of its turns.

Kinetic studies on strand displacement in de novo designed parallel heterodimeric coiled coils.

PubMed

Groth, Mike C; Rink, W Mathis; Meyer, Nils F; Thomas, Franziska

2018-05-14

Among the protein folding motifs, which are accessible by de novo design, the parallel heterodimeric coiled coil is most frequently used in bioinspired applications and chemical biology in general. This is due to the straightforward sequence-to-structure relationships, which it has in common with all coiled-coil motifs, and the heterospecificity, which allows control of association. Whereas much focus was laid on designing orthogonal coiled coils, systematic studies on controlling association, for instance by strand displacement, are rare. As a contribution to the design of dynamic coiled-coil-based systems, we studied the strand-displacement mechanism in obligate heterodimeric coiled coils to investigate the suitability of the dissociation constants ( K D ) as parameters for the prediction of the outcome of strand-displacement reactions. We use two sets of heterodimeric coiled coils, the previously reported N-A x B y and the newly characterized C-A x B y . Both comprise K D values in the μM to sub-nM regime. Strand displacement is explored by CD titration and a FRET-based kinetic assay and is proved to be an equilibrium reaction with half-lifes from a few seconds up to minutes. We could fit the displacement data by a competitive binding model, giving rate constants and overall affinities of the underlying association and dissociation reactions. The overall affinities correlate well with the ratios of K D values determined by CD-thermal denaturation experiments and, hence, support the dissociative mechanism of strand displacement in heterodimeric coiled coils. From the results of more than 100 different displacement reactions we are able to classify three categories of overall affinities, which allow for easy prediction of the equilibrium of strand displacement in two competing heterodimeric coiled coils.

Structural mapping of the coiled-coil domain of a bacterial condensin and comparative analyses across all domains of life suggest conserved features of SMC proteins.

PubMed

Waldman, Vincent M; Stanage, Tyler H; Mims, Alexandra; Norden, Ian S; Oakley, Martha G

2015-06-01

The structural maintenance of chromosomes (SMC) proteins form the cores of multisubunit complexes that are required for the segregation and global organization of chromosomes in all domains of life. These proteins share a common domain structure in which N- and C- terminal regions pack against one another to form a globular ATPase domain. This "head" domain is connected to a central, globular, "hinge" or dimerization domain by a long, antiparallel coiled coil. To date, most efforts for structural characterization of SMC proteins have focused on the globular domains. Recently, however, we developed a method to map interstrand interactions in the 50-nm coiled-coil domain of MukB, the divergent SMC protein found in γ-proteobacteria. Here, we apply that technique to map the structure of the Bacillus subtilis SMC (BsSMC) coiled-coil domain. We find that, in contrast to the relatively complicated coiled-coil domain of MukB, the BsSMC domain is nearly continuous, with only two detectable coiled-coil interruptions. Near the middle of the domain is a break in coiled-coil structure in which there are three more residues on the C-terminal strand than on the N-terminal strand. Close to the head domain, there is a second break with a significantly longer insertion on the same strand. These results provide an experience base that allows an informed interpretation of the output of coiled-coil prediction algorithms for this family of proteins. A comparison of such predictions suggests that these coiled-coil deviations are highly conserved across SMC types in a wide variety of organisms, including humans. © 2015 Wiley Periodicals, Inc.

Design of catheter radio frequency coils using coaxial transmission line resonators for interventional neurovascular MR imaging.

PubMed

Zhang, Xiaoliang; Martin, Alastair; Jordan, Caroline; Lillaney, Prasheel; Losey, Aaron; Pang, Yong; Hu, Jeffrey; Wilson, Mark; Cooke, Daniel; Hetts, Steven W

2017-04-01

It is technically challenging to design compact yet sensitive miniature catheter radio frequency (RF) coils for endovascular interventional MR imaging. In this work, a new design method for catheter RF coils is proposed based on the coaxial transmission line resonator (TLR) technique. Due to its distributed circuit, the TLR catheter coil does not need any lumped capacitors to support its resonance, which simplifies the practical design and construction and provides a straightforward technique for designing miniature catheter-mounted imaging coils that are appropriate for interventional neurovascular procedures. The outer conductor of the TLR serves as an RF shield, which prevents electromagnetic energy loss, and improves coil Q factors. It also minimizes interaction with surrounding tissues and signal losses along the catheter coil. To investigate the technique, a prototype catheter coil was built using the proposed coaxial TLR technique and evaluated with standard RF testing and measurement methods and MR imaging experiments. Numerical simulation was carried out to assess the RF electromagnetic field behavior of the proposed TLR catheter coil and the conventional lumped-element catheter coil. The proposed TLR catheter coil was successfully tuned to 64 MHz for proton imaging at 1.5 T. B 1 fields were numerically calculated, showing improved magnetic field intensity of the TLR catheter coil over the conventional lumped-element catheter coil. MR images were acquired from a dedicated vascular phantom using the TLR catheter coil and also the system body coil. The TLR catheter coil is able to provide a significant signal-to-noise ratio (SNR) increase (a factor of 200 to 300) over its imaging volume relative to the body coil. Catheter imaging RF coil design using the proposed coaxial TLR technique is feasible and advantageous in endovascular interventional MR imaging applications.

Measurement of heating coil temperature for e-cigarettes with a "top-coil" clearomizer.

PubMed

Chen, Wenhao; Wang, Ping; Ito, Kazuhide; Fowles, Jeff; Shusterman, Dennis; Jaques, Peter A; Kumagai, Kazukiyo

2018-01-01

To determine the effect of applied power settings, coil wetness conditions, and e-liquid compositions on the coil heating temperature for e-cigarettes with a "top-coil" clearomizer, and to make associations of coil conditions with emission of toxic carbonyl compounds by combining results herein with the literature. The coil temperature of a second generation e-cigarette was measured at various applied power levels, coil conditions, and e-liquid compositions, including (1) measurements by thermocouple at three e-liquid fill levels (dry, wet-through-wick, and full-wet), three coil resistances (low, standard, and high), and four voltage settings (3-6 V) for multiple coils using propylene glycol (PG) as a test liquid; (2) measurements by thermocouple at additional degrees of coil wetness for a high resistance coil using PG; and (3) measurements by both thermocouple and infrared (IR) camera for high resistance coils using PG alone and a 1:1 (wt/wt) mixture of PG and glycerol (PG/GL). For single point thermocouple measurements with PG, coil temperatures ranged from 322 ‒ 1008°C, 145 ‒ 334°C, and 110 ‒ 185°C under dry, wet-through-wick, and full-wet conditions, respectively, for the total of 13 replaceable coil heads. For conditions measured with both a thermocouple and an IR camera, all thermocouple measurements were between the minimum and maximum across-coil IR camera measurements and equal to 74% ‒ 115% of the across-coil mean, depending on test conditions. The IR camera showed details of the non-uniform temperature distribution across heating coils. The large temperature variations under wet-through-wick conditions may explain the large variations in formaldehyde formation rate reported in the literature for such "top-coil" clearomizers. This study established a simple and straight-forward protocol to systematically measure e-cigarette coil heating temperature under dry, wet-through-wick, and full-wet conditions. In addition to applied power, the composition of e-liquid, and the devices' ability to efficiently deliver e-liquid to the heating coil are important product design factors effecting coil operating temperature. Precautionary temperature checks on e-cigarettes under manufacturer-recommended normal use conditions may help to reduce the health risks from exposure to toxic carbonyl emissions associated with coil overheating.

Comparison of endorectal coil and nonendorectal coil T2W and diffusion-weighted MRI at 3 Tesla for localizing prostate cancer: correlation with whole-mount histopathology.

PubMed

Turkbey, Baris; Merino, Maria J; Gallardo, Elma Carvajal; Shah, Vijay; Aras, Omer; Bernardo, Marcelino; Mena, Esther; Daar, Dagane; Rastinehad, Ardeshir R; Linehan, W Marston; Wood, Bradford J; Pinto, Peter A; Choyke, Peter L

2014-06-01

To compare utility of T2-weighted (T2W) MRI and diffusion-weighted MRI (DWI-MRI) obtained with and without an endorectal coil at 3 Tesla (T) for localizing prostate cancer. This Institutional Review Board-approved study included 20 patients (median prostate-specific antigen, 8.4 ng/mL). Patients underwent consecutive prostate MRIs at 3T, first with a surface coil alone, then with combination of surface, endorectal coils (dual coil) followed by robotic assisted radical prostatectomy. Lesions were mapped at time of acquisition on dual-coil T2W, DWI-MRI. To avoid bias, 6 months later nonendorectal coil T2W, DWI-MRI were mapped. Both MRI evaluations were performed by two readers blinded to pathology with differences resolved by consensus. A lesion-based correlation with whole-mount histopathology was performed. At histopathology 51 cancer foci were present ranging in size from 2 to 60 mm. The sensitivity of the endorectal dual-coil, nonendorectal coil MRIs were 0.76, 0.45, respectively. PPVs for endorectal dual-coil, nonendorectal coil MRI were 0.80, 0.64, respectively. Mean size of detected lesions with nonendorectal coil MRI were larger than those detected by dual-coil MRI (22 mm versus 17.4 mm). Dual-coil prostate MRI detected more cancer foci than nonendorectal coil MRI. While nonendorectal coil MRI is an attractive alternative, physicians performing prostate MRI should be aware of its limitations. Copyright © 2013 Wiley Periodicals, Inc.

Sensitivity of an eight-element phased array coil in 3 Tesla MR imaging: a basic analysis.

PubMed

Hiratsuka, Yoshiyasu; Miki, Hitoshi; Kikuchi, Keiichi; Kiriyama, Ikuko; Mochizuki, Teruhito; Takahashi, Shizue; Sadamoto, Kazuhiko

2007-01-01

To evaluate the performance advantages of an 8-element phased array head coil (8 ch coil) over a conventional quadrature-type birdcage head coil (QD coil) with regard to the signal-to-noise ratio (SNR) and image uniformity in 3 Tesla magnetic resonance (MR) imaging. We scanned a phantom filled with silicon oil using an 8 ch coil and a QD coil in a 3T MR imaging system and compared the SNR and image uniformity obtained from T(1)-weighted spin echo (SE) images and T(2)-weighted fast SE images between the 2 coils. We also visually evaluated images from 4 healthy volunteers. The SNR with the 8 ch coil was approximately twice that with the QD coil in the region of interest (ROI), which was set as 75% of the area in the center of the phantom images. With regard to the spatial variation of sensitivity, the SNR with the 8 ch coil was lower at the center of the images than at the periphery, whereas the SNR with the QD coil exhibited an inverse pattern. At the center of the images with the 8 ch coil, the SNR was somewhat lower, and that distribution was relatively flat compared to that in the periphery. Image uniformity varied less with the 8 ch coil than with the QD coil on both imaging sequences. The 8 ch phased array coil was useful for obtaining high quality 3T images because of its higher SNR and improved image uniformity than those obtained with conventional quadrature-type birdcage head coil.

Crystal Structure of a Coiled-Coil Domain from Human ROCK I

PubMed Central

Tu, Daqi; Li, Yiqun; Song, Hyun Kyu; Toms, Angela V.; Gould, Christopher J.; Ficarro, Scott B.; Marto, Jarrod A.; Goode, Bruce L.; Eck, Michael J.

2011-01-01

The small GTPase Rho and one of its targets, Rho-associated kinase (ROCK), participate in a variety of actin-based cellular processes including smooth muscle contraction, cell migration, and stress fiber formation. The ROCK protein consists of an N-terminal kinase domain, a central coiled-coil domain containing a Rho binding site, and a C-terminal pleckstrin homology domain. Here we present the crystal structure of a large section of the central coiled-coil domain of human ROCK I (amino acids 535–700). The structure forms a parallel α-helical coiled-coil dimer that is structurally similar to tropomyosin, an actin filament binding protein. There is an unusual discontinuity in the coiled-coil; three charged residues (E613, R617 and D620) are positioned at what is normally the hydrophobic core of coiled-coil packing. We speculate that this conserved irregularity could function as a hinge that allows ROCK to adopt its autoinhibited conformation. PMID:21445309

Performance evaluation of matrix gradient coils.

PubMed

Jia, Feng; Schultz, Gerrit; Testud, Frederik; Welz, Anna Masako; Weber, Hans; Littin, Sebastian; Yu, Huijun; Hennig, Jürgen; Zaitsev, Maxim

2016-02-01

In this paper, we present a new performance measure of a matrix coil (also known as multi-coil) from the perspective of efficient, local, non-linear encoding without explicitly considering target encoding fields. An optimization problem based on a joint optimization for the non-linear encoding fields is formulated. Based on the derived objective function, a figure of merit of a matrix coil is defined, which is a generalization of a previously known resistive figure of merit for traditional gradient coils. A cylindrical matrix coil design with a high number of elements is used to illustrate the proposed performance measure. The results are analyzed to reveal novel features of matrix coil designs, which allowed us to optimize coil parameters, such as number of coil elements. A comparison to a scaled, existing multi-coil is also provided to demonstrate the use of the proposed performance parameter. The assessment of a matrix gradient coil profits from using a single performance parameter that takes the local encoding performance of the coil into account in relation to the dissipated power.

Cool-Down and Current Test Results of the KSTAR Prototype TF Coil

NASA Astrophysics Data System (ADS)

Oh, Y. K.; Lee, S.; Chu, Y.; Park, K. R.; Yonekawa, H.; Baek, S. H.; Cho, K. W.; Park, Y. M.; Kim, M. K.; Chang, H. S.; Kim, Y. S.; Chang, Y. B.; Lee, Y. J.; Kim, W. C.; Kim, K.; Kwag, S. W.; Lee, S. H.; Yang, S. H.; Lee, S. J.; Bak, J. S.; Lee, G. S.

2004-06-01

A prototype toroidal field (TF) coil, TF00 coil, of the Korea Superconducting Tokamak Advanced Research (KSTAR) project has been assembled and tested at the coil test facility in Korea Basic Science Institute (KBSI). The TF00 coil is a real-sized TF coil made of Nb3Sn superconducting cable-in-conduit conductor (CICC). The coil test was conducted by several campaigns according to the objectives. The first campaign, which was carried out by Jan. 2003, has objectives of cooling the coil into operating temperature and finding any defect in the coil such as cold leaks. From the results of the first campaign experiment, any defect in the coil was not found. The second campaign, which was carried out by Aug. 2003, has objectives to get the operating characteristics according to the current ramp up and discharge operations. In this paper, the coil test results are introduced as well as the details of the coil test system setup.

Crystal Structure of the Central Coiled-Coil Domain from Human Liprin-[beta]2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stafford, Ryan L.; Tang, Ming-Yun; Sawaya, Michael R.

2012-02-07

Liprins are a conserved family of scaffolding proteins important for the proper regulation and development of neuronal synapses. Humans have four liprin-{alpha}s and two liprin-{beta}s which all contain long coiled-coil domains followed by three tandem SAM domains. Complex interactions between the coiled-coil and SAM domains are thought to create liprin scaffolds, but the structural and biochemical properties of these domains remain largely uncharacterized. In this study we find that the human liprin-{beta}2 coiled-coil forms an extended dimer. Several protease-resistant subdomains within the liprin-{beta}1 and liprin-{beta}2 coiled-coils were also identified. A 2.0 {angstrom} crystal structure of the central, protease-resistant core ofmore » the liprin-{beta}2 coiled-coil reveals a parallel helix orientation. These studies represent an initial step toward determining the overall architecture of liprin scaffolds and understanding the molecular basis for their synaptic functions.« less

Dynamic allostery of protein alpha helical coiled-coils

PubMed Central

Hawkins, Rhoda J; McLeish, Tom C.B

2005-01-01

Alpha helical coiled-coils appear in many important allosteric proteins such as the dynein molecular motor and bacteria chemotaxis transmembrane receptors. As a mechanism for transmitting the information of ligand binding to a distant site across an allosteric protein, an alternative to conformational change in the mean static structure is an induced change in the pattern of the internal dynamics of the protein. We explore how ligand binding may change the intramolecular vibrational free energy of a coiled-coil, using parameterized coarse-grained models, treating the case of dynein in detail. The models predict that coupling of slide, bend and twist modes of the coiled-coil transmits an allosteric free energy of ∼2kBT, consistent with experimental results. A further prediction is a quantitative increase in the effective stiffness of the coiled-coil without any change in inherent flexibility of the individual helices. The model provides a possible and experimentally testable mechanism for transmission of information through the alpha helical coiled-coil of dynein. PMID:16849225

[Development of RF coil of permanent magnet mini-magnetic resonance imager and mouse imaging experiments].

PubMed

Hou, Shulian; Xie, Huantong; Chen, Wei; Wang, Guangxin; Zhao, Qiang; Li, Shiyu

2014-10-01

In the development of radio frequency (RF) coils for better quality of the mini-type permanent magnetic resonance imager for using in the small animal imaging, the solenoid RF coil has a special advantage for permanent magnetic system based on analyses of various types.of RF coils. However, it is not satisfied for imaging if the RF coils are directly used. By theoretical analyses of the magnetic field properties produced from the solenoid coil, the research direction was determined by careful studies to raise further the uniformity of the magnetic field coil, receiving coil sensitivity for signals and signal-to-noise ratio (SNR). The method had certain advantages and avoided some shortcomings of the other different coil types, such as, birdcage coil, saddle shaped coil and phased array coil by using the alloy materials (from our own patent). The RF coils were designed, developed and made for keeled applicable to permanent magnet-type magnetic resonance imager, multi-coil combination-type, single-channel overall RF receiving coil, and applied for a patent. Mounted on three instruments (25 mm aperture, with main magnetic field strength of 0.5 T or 1.5 T, and 50 mm aperture, with main magnetic field strength of 0.48 T), we performed experiments with mice, rats, and nude mice bearing tumors. The experimental results indicated that the RF receiving coil was fully applicable to the permanent magnet-type imaging system.

A Mechanical Coil Insertion System for Endovascular Coil Embolization of Intracranial Aneurysms

PubMed Central

Haraguchi, K.; Miyachi, S.; Matsubara, N.; Nagano, Y.; Yamada, H.; Marui, N.; Sano, A.; Fujimoto, H.; Izumi, T.; Yamanouchi, T.; Asai, T.; Wakabayashi, T.

2013-01-01

Summary Like other fields of medicine, robotics and mechanization might be introduced into endovascular coil embolization of intracranial aneurysms for effective treatment. We have already reported that coil insertion force could be smaller and more stable when the coil delivery wire is driven mechanically at a constant speed. Another background is the difficulty in synchronizing operators' minds and hands when two operators control the microcatheter and the coil respectively. We have therefore developed a mechanical coil insertion system enabling a single operator to insert coils at a fixed speed while controlling the microcatheter. Using our new system, the operator manipulated the microcatheter with both hands and drove the coil using foot switches simultaneously. A delivery wire force sensor previously reported was used concurrently, allowing the operator to detect excessive stress on the wire. In vitro coil embolization was performed using three methods: simple mechanical advance of the coil; simple mechanical advance of the coil with microcatheter control; and driving (forward and backward) of the coil using foot switches in addition to microcatheter control. The system worked without any problems, and did not interfere with any procedures. In experimental coil embolization, delivery wire control using the foot switches as well as microcatheter manipulation helped to achieve successful insertion of coils. This system could offer the possibility of developing safer and more efficient coil embolization. Although we aim at total mechanization and automation of procedures in the future, microcatheter manipulation and synchronized delivery wire control are still indispensable using this system. PMID:23693038

Flux pumping for non-insulated and metal-insulated HTS coils

NASA Astrophysics Data System (ADS)

Ma, Jun; Geng, Jianzhao; Coombs, T. A.

2018-01-01

High-temperature superconducting (HTS) coils wound from coated conductors without turn-to-turn insulation (non-insulated (NI) coils) have been proven with excellent electrical and thermal performances. However, the slow charging of NI coils has been a long-lasting problem. In this work, we explore using a transformer-rectifier HTS flux pump to charge an NI coil and a metal-insulated coil. The charging performance comparison is made between different coils. Comprehensive study is done to thoroughly understand the electrical-magnetic transience in charging these coils. We will show that the low-voltage high-current flux pump is especially suitable for charging NI coils with very low characteristic resistance.

Endovascular rescue method for undesirably stretched coil.

PubMed

Cho, Jae Hoon

2014-10-01

Undesirable detachment or stretching of coils within the parent artery during aneurysm embolization can be related with thrombus formation, which can be caused occlusion of parent artery or embolic event(s). To escape from this situation, several rescue methods have been reported. A case with undesirably stretched coil in which another rescue method was used, is presented. When the stretched coil is still located in the coil delivery microcatheter, the stretched coil can be removed safely using a snare and a handmade monorail microcatheter. After a snare is lodged in the handmade monorail microcatheter, the snare is introduced over the coil delivery micorcatheter and located in the distal part of the stretched coil. After then, the handmade monorail microcatheter captures the stretched coil and the snare as one unit. This technique using a handmade monorail microcatheter and a snare can be a good rescue modality for the undesirably stretched coil, still remained within the coil delivery microcatheter.

Endovascular Rescue Method for Undesirably Stretched Coil

PubMed Central

2014-01-01

Undesirable detachment or stretching of coils within the parent artery during aneurysm embolization can be related with thrombus formation, which can be caused occlusion of parent artery or embolic event(s). To escape from this situation, several rescue methods have been reported. A case with undesirably stretched coil in which another rescue method was used, is presented. When the stretched coil is still located in the coil delivery microcatheter, the stretched coil can be removed safely using a snare and a handmade monorail microcatheter. After a snare is lodged in the handmade monorail microcatheter, the snare is introduced over the coil delivery micorcatheter and located in the distal part of the stretched coil. After then, the handmade monorail microcatheter captures the stretched coil and the snare as one unit. This technique using a handmade monorail microcatheter and a snare can be a good rescue modality for the undesirably stretched coil, still remained within the coil delivery microcatheter. PMID:25371791

Radiation-hard electrical coil and method for its fabrication

DOEpatents

Grieggs, R.J.; Blake, R.D.; Gac, F.D.

1982-06-29

A radiation-hard insulated electrical coil and method for making the same are disclosed. In accordance with the method, a conductor, preferably copper, is wrapped with an aluminum strip and then tightly wound into a coil. The aluminum-wrapped coil is then annealed to relax the conductor in the coiled configuration. The annealed coil is then immersed in an alkaline solution to dissolve the aluminum strip, leaving the bare conductor in a coiled configuration with all of the windings closely packed yet uniformly spaced from one another. The coil is then insulated with a refractory insulating material. In the preferred embodiment, the coil is insulated by coating it with a vitreous enamel and subsequently potting the enamelled coil in a castable ceramic concrete. The resulting coil is substantially insensitive to radiation and may be operated continuously in high radiation environments for long periods of time.

Development and positioning reliability of a TMS coil holder for headache research.

PubMed

Chronicle, Edward P; Pearson, A Jane; Matthews, Cheryl

2005-01-01

Accurate and reproducible coil positioning is important for headache research using transcranial magnetic stimulation protocols. We aimed to design a transcranial magnetic stimulation coil holder and demonstrate reliability of test-retest coil positioning. A coil holder was developed and manufactured according to three principles of stability, durability, and three-dimensional positional accuracy. Reliability of coil positioning was assessed by stimulating over the motor cortex of four neurologically normal subjects and recording finger muscle responses, both at a test phase and a retest phase several hours later. In all four subjects, repositioning of the transcranial magnetic stimulation coil solely on the basis of coil holder coordinates was accurate to within 2 mm. The coil holder demonstrated good test-retest reliability of coil positioning, and is thus a promising tool for transcranial magnetic stimulation-based headache research, particularly studies of prophylactic drug effect where several laboratory visits with identical coil positioning are necessary.

Inductance and resistance measurement method for vessel detection and coil powering in all-surface inductive heating systems composed of outer squircle coils

NASA Astrophysics Data System (ADS)

Kilic, Veli Tayfun; Unal, Emre; Demir, Hilmi Volkan

2017-05-01

In this work, we investigate a method proposed for vessel detection and coil powering in an all-surface inductive heating system composed of outer squircle coils. Besides conventional circular coils, coils with different shapes such as outer squircle coils are used for and enable efficient all-surface inductive heating. Validity of the method, which relies on measuring inductance and resistance values of a loaded coil at different frequencies, is experimentally demonstrated for a coil with shape different from conventional circular coil. Simple setup was constructed with a small coil to model an all-surface inductive heating system. Inductance and resistance maps were generated by measuring coil's inductance and resistance values at different frequencies loaded by a plate made of different materials and located at various positions. Results show that in an induction hob for various coil geometries it is possible to detect a vessel's presence, to identify its material type and to specify its position on the hob surface by considering inductance and resistance of the coil measured on at least two different frequencies. The studied method is important in terms of enabling safe, efficient and user flexible heating in an all-surface inductive heating system by automatically detecting the vessel's presence and powering on only the coils that are loaded by the vessel with predetermined current levels.

The Optical Flow Technique on the Research of Solar Non-potentiality

NASA Astrophysics Data System (ADS)

Liu, Ji-hong; Zhang, Hong-qi

2010-06-01

Several optical flow techniques, which have being applied to the researches of solar magnetic non-potentiality recently, have been summarized here. And a few new non-potential parameters which can be derived from them have been discussed, too. The main components of the work are presented as follows: (1) The optical flow techniques refers to a series of new image analyzing techniques arisen recently on the researches of solar magnetic non-potentiality. They mainly include LCT (local correlation tracking), ILCT (inductive equation combining with LCT), MEF (minimum energy effect), DAVE (differential affine velocity estimator) and NAVE (nonlinear affine velocity estimator). Their calculating and applying conditions, merits and deficiencies, all have been discussed detailedly in this work. (2) Benefit from the optical flow techniques, the transverse velocity fields of the magnetic features on the solar surface may be determined by a time sequence of high-quality images currently produced by high-resolution observations either from the ground or in space. Consequently, several new non-potential parameters may be acquired, such as the magnetic helicity flux, the induced electric field in the photosphere, the non-potential magnetic stress (whose area integration is the Lorentz force), etc. Then we can determine the energy flux across the photosphere, and subsequently evaluate the energy budget. Former works on them by small or special samples have shown that they are probably related closely to the erupting events, such as flare, filament eruptions and coronal mass ejections.

Association of Lactase Persistence Genotypes with High Intake of Dairy Saturated Fat and High Prevalence of Lactase Non-Persistence among the Mexican Population.

PubMed

Ojeda-Granados, Claudia; Panduro, Arturo; Rebello Pinho, João Renato; Ramos-Lopez, Omar; Gleyzer, Ketti; Malta, Fernanda de Mello; Gonzalez-Aldaco, Karina; Roman, Sonia

2016-01-01

Lactase (LCT) -13910 C>T and -22018 G>A polymorphisms associated with the lactase non-persistence (LNP)/persistence (LP) phenotypes vary globally. LP has been associated with obesity in Europeans. However, it has not been genetically evaluated in Mexico, a country with admixed population, recent introduction of dairy, and a high prevalence of obesity. Thus, we aimed to determine the distribution of the LCT polymorphisms and their association with the nutritional profile of West Mexico's populations. Genotyping of 1,196 individuals (natives and mestizos) was carried out by a Taqman allelic discrimination assay. Descriptive statistics and interpopulation analyzes were performed by SPSS, Arlequin, and Structure software. Demographic, anthropometric, biochemical and dietary data were analyzed in 212 mestizos. LNP genotypes mainly prevailed (CC 68.7% and GG 68.2%); both predominated in native Huicholes and Nahuas (>97.7%). Among the mestizos, the LP genotypes were associated with a higher intake of saturated fat (9.9 ± 3.9% vs. 8.5 ± 4.0%, p = 0.018; OR = 2.55, 95% CI 1.29-5.03, p = 0.006) and a daily/more frequent consumption of dairy (88.8 vs. 78.0%; p = 0.049) than LNP genotypes. The LNP trait was predominant in Mexicans with a major Amerindian ancestry. A daily consumption of dairy was associated with a higher intake of saturated fat in LP individuals. © 2016 S. Karger AG, Basel.

Lantibiotic engineering: molecular characterization and exploitation of lantibiotic-synthesizing enzymes for peptide engineering.

PubMed

Nagao, Jun-ichi; Aso, Yuji; Shioya, Kouki; Nakayama, Jiro; Sonomoto, Kenji

2007-01-01

Lanthionine-containing peptide antibiotics called lantibiotics are produced by a large number of Gram-positive bacteria. Nukacin ISK-1 produced by Staphylococcus warneri ISK-1 is type-A(II) lantibiotic. Ribosomally synthesized nukacin ISK-1 prepeptide (NukA) consists of an N-terminal leader peptide followed by a C-terminal propeptide moiety that undergoes several post-translational modification events including unusual amino acid formation by the modification enzyme NukM, cleavage of leader peptide and export by the dual functional ABC transporter NukT, finally yielding a biologically active peptide. Unusual amino acids in lantibiotics contribute to biological activity and also structural stability against proteases. Thus, lantibiotic-synthesizing enzymes have a high potentiality for peptide engineering by introduction of unusual amino acids into desired peptides with altering biological and physicochemical properties, e.g., activity and stability, termed lantibiotic engineering. We report the establishment of a heterologous expression of nukacin ISK-1 biosynthetic gene cluster by the nisin-controlled expression system and discuss our recent progress in understanding of the biosynthetic enzymes for nukacin ISK-1 such as localization, molecular interaction in biophysical and biochemical aspects. Substrate specificity of the lantibiotic-synthesizing enzymes was evaluated by complementation of the biosynthetic enzymes (LctM and LctT) of closely related lantibiotic lacticin 481 for nukacin ISK-1 biosynthesis. We further explored a rapid and powerful tool for introduction of unusual amino acids by co-expression of hexa-histidine-tagged NukA and NukM in Escherichia coli.

Body fat and dairy product intake in lactase persistent and non-persistent children and adolescents.

PubMed

Almon, Ricardo; Patterson, Emma; Nilsson, Torbjörn K; Engfeldt, Peter; Sjöström, Michael

2010-06-16

Lactase non-persistent (LNP) individuals may be lactose intolerant and therefore on a more restricted diet concerning milk and milk products compared to lactase persistent (LP) individuals. This may have an impact on body fat mass. This study examines if LP and LNP children and adolescents, defined by genotyping for the LCT-13910 C > T polymorphism, differ from each other with regard to milk and milk product intake, and measures of body fat mass. Children (n=298, mean age 9.6 years) and adolescents (n=386, mean age 15.6 years), belonging to the Swedish part of the European Youth Heart Study, were genotyped for the LCT-13910 C > T polymorphism. Dietary intakes of reduced and full-fat dairy varieties were determined. LNP (CC genotype) subjects consumed less milk, soured milk and yoghurt compared to LP (CT/TT genotype) subjects (p<0.001). Subsequent partitioning for age group attenuated this observation (p=0.002 for children and p=0.023 in adolescents). Six subjects were reported by parents to be 'lactose intolerant', none of whom were LNP. LNP children and adolescents consumed significantly less reduced fat milk and milk products than LP children and adolescents (p=0.009 for children and p=0.001 for adolescents). We conclude that LP is linked to an overall higher milk and dairy intake, but is not linked to higher body fat mass in children and adolescents.

Diagnostic imaging and interventional therapy of hepatocellular carcinoma.

PubMed

Palma, L D

1998-08-01

Diagnostic imaging has many important roles in the management of patients with hepatocellular carcinoma (HCC). In diagnosis, lipiodol CT (LCT) has been shown to be the most sensitive imaging modality (90-97%) for all sizes of lesions; all other modalities have high sensitivities for lesions 1-3 cm but low sensitivities for lesions < 1 cm (ultrasound 33-37%, conventional CT 20-42% and digital subtraction angiography 40-55%). All imaging modalities understage HCC. Once again LCT is the most accurate method of evaluating the extent of tumour, but even this method does not identify all satellite nodules. Ultrasound has been proposed as a screening method, but this cannot be justified on the basis of its results or cost benefit analysis. Both CT and dynamic MRI play useful roles in evaluating the efficacy and follow-up of patients undergoing chemoembolization (TACE) and percutaneous ethanol injection (PEI). Although surgery remains the best treatment of HCC, it is unsuitable in most of the cases which would be better treated with interventional therapy. This article presents a review of the literature regarding the use of TACE, PEI or a combination of both procedures in the treatment of HCC. A multicentric study has shown that patients with monofocal lesions less than 5 cm in diameter are better treated with PEI, which is therefore a good alternative to the surgical treatment; patients with multifocal lesions (maximum of three lesions) show a better survival with TACE. Combined treatment with TACE and PEI proves to be effective in patients with large HCC.

Monorail snare technique for the recovery of stretched platinum coils: technical case report.

PubMed

Fiorella, David; Albuquerque, Felipe C; Deshmukh, Vivek R; McDougall, Cameron G

2005-07-01

Coil stretching represents a potentially hazardous technical complication not infrequently encountered during the embolization of cerebral aneurysms. Often, the stretched coil cannot be advanced into the aneurysm or withdrawn intact. The operator is then forced to attempt to retract the damaged coil, which may result in coil breakage, leaving behind a significant length of potentially thrombogenic stretched coil material within the parent vessel. To overcome this problem, we devised a technique to snare the distal, unstretched, intact portion of the platinum coil by use of the indwelling microcatheter and stretched portion of the coil as a monorail guide. We have used this technique successfully in four patients to snare coils stretched during cerebral aneurysm embolization. Three of these patients were undergoing Neuroform (Boston Scientific/Target, Fremont, CA) stent-supported coil embolization of unruptured aneurysms. In all cases, the snare was advanced easily to the targeted site for coil engagement by use of the microcatheter as a monorail guide. Once the intact distal segment of the coil was ensnared, coil removal was uneventful, with no disturbance of the remainder of the indwelling coil pack or Neuroform stent. A 2-mm Amplatz Goose Neck microsnare (Microvena Corp., White Bear Lake, MN) was placed through a Prowler-14 microcatheter (Cordis Corp., Miami, FL). The hub of the indwelling SL-10 microcatheter (Boston Scientific, Natick, MA) was then cut away with a scalpel, leaving the coil pusher wire intact, and removed. The open 2-mm snare was then advanced over the outside of the coil pusher wire and microcatheter. The snare and Prowler-14 microcatheter were then advanced into the guiding catheter (6- or 7-French) as a unit over the indwelling SL-10 microcatheter. By use of the SL-10 microcatheter and coil as a "monorail" guide, the snare was advanced over and beyond the microcatheter and the stretched portion of the coil until the snare was in position to engage the distal unstretched coil. At this point, the snare was then closed around the intact portion of the coil, and the microcatheters, snare, and coil were removed as a unit. The monorail snare technique represents a fast, safe, and easy method by which a stretched coil can be removed.

Comprehensive Survey on Improved Focality and Penetration Depth of Transcranial Magnetic Stimulation Employing Multi-Coil Arrays.

PubMed

Wei, Xile; Li, Yao; Lu, Meili; Wang, Jiang; Yi, Guosheng

2017-11-14

Multi-coil arrays applied in transcranial magnetic stimulation (TMS) are proposed to accurately stimulate brain tissues and modulate neural activities by an induced electric field (EF). Composed of numerous independently driven coils, a multi-coil array has alternative energizing strategies to evoke EFs targeting at different cerebral regions. To improve the locating resolution and the stimulating focality, we need to fully understand the variation properties of induced EFs and the quantitative control method of the spatial arrangement of activating coils, both of which unfortunately are still unclear. In this paper, a comprehensive analysis of EF properties was performed based on multi-coil arrays. Four types of planar multi-coil arrays were used to study the relationship between the spatial distribution of EFs and the structure of stimuli coils. By changing coil-driven strategies in a basic 16-coil array, we find that an EF induced by compactly distributed coils decays faster than that induced by dispersedly distributed coils, but the former has an advantage over the latter in terms of the activated brain volume. Simulation results also indicate that the attenuation rate of an EF induced by the 36-coil dense array is 3 times and 1.5 times greater than those induced by the 9-coil array and the 16-coil array, respectively. The EF evoked by the 36-coil dispense array has the slowest decay rate. This result demonstrates that larger multi-coil arrays, compared to smaller ones, activate deeper brain tissues at the expense of decreased focality. A further study on activating a specific field of a prescribed shape and size was conducted based on EF variation. Accurate target location was achieved with a 64-coil array 18 mm in diameter. A comparison between the figure-8 coil, the planar array, and the cap-formed array was made and demonstrates an improvement of multi-coil configurations in the penetration depth and the focality. These findings suggest that there is a tradeoff between attenuation rate and focality in the application of multi-coil arrays. Coil-energizing strategies and array dimensions should be based on an adequate evaluation of these two important demands and the topological structure of target tissues.

Designed Coiled-Coil Peptides Inhibit the Type Three Secretion System of Enteropathogenic Escherichia coli

PubMed Central

Larzábal, Mariano; Mercado, Elsa C.; Vilte, Daniel A.; Salazar-González, Hector; Cataldi, Angel; Navarro-Garcia, Fernando

2010-01-01

Background Enteropathogenic E. coli (EPEC) and enterohemorrhagic E. coli (EHEC) are two categories of E. coli strains associated with human disease. A major virulence factor of both pathotypes is the expression of a type three secretion system (TTSS), responsible for their ability to adhere to gut mucosa causing a characteristic attaching and effacing lesion (A/E). The TTSS translocates effector proteins directly into the host cell that subvert mammalian cell biochemistry. Methods/Principal Findings We examined synthetic peptides designed to inhibit the TTSS. CoilA and CoilB peptides, both representing coiled-coil regions of the translocator protein EspA, and CoilD peptide, corresponding to a coiled–coil region of the needle protein EscF, were effective in inhibiting the TTSS dependent hemolysis of red blood cells by the EPEC E2348/69 strain. CoilA and CoilB peptides also reduced the formation of actin pedestals by the same strain in HEp-2 cells and impaired the TTSS-mediated protein translocation into the epithelial cell. Interestingly, CoilA and CoilB were able to block EspA assembly, destabilizing the TTSS and thereby Tir translocation. This blockage of EspA polymerization by CoilA or CoilB peptides, also inhibited the correct delivery of EspB and EspD as detected by immunoblotting. Interestingly, electron microscopy of bacteria incubated with the CoilA peptide showed a reduction of the length of EspA filaments. Conclusions Our data indicate that coiled-coil peptides can prevent the assembly and thus the functionality of the TTSS apparatus and suggest that these peptides could provide an attractive tool to block EPEC and EHEC pathogenesis. PMID:20140230

Embolization of the Gastroduodenal Artery Before Selective Internal Radiotherapy: A Prospectively Randomized Trial Comparing Standard Pushable Coils with Fibered Interlock Detachable Coils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dudeck, Oliver, E-mail: oliver.dudeck@med.ovgu.de; Bulla, Karsten; Wieners, Gero

2011-02-15

The purpose of this study was compare embolization of the gastroduodenal artery (GDA) using standard pushable coils with the Interlock detachable coil (IDC), a novel fibered mechanically detachable long microcoil, in patients scheduled for selective internal radiotherapy (SIRT). Fifty patients (31 male and 19 female; median age 66.6 {+-} 8.1 years) were prospectively randomized for embolization using either standard coils or IDCs. Procedure time, radiation dose, number of embolization devices, complications, and durability of vessel occlusion at follow-up angiography were recorded. The procedures differed significantly in time (14:32 {+-} 5:56 min for standard coils vs. 2:13 {+-} 1:04 min formore » IDCs; p < 0.001); radiation dose for coil deployment (2479 {+-} 1237 cGycm Superscript-Two for standard coils vs. 275 {+-} 268 cGycm Superscript-Two for IDCs; p < 0.001); and vessel occlusion (17:18 {+-} 6:39 min for standard coils vs. 11:19 {+-} 7:54 min for IDCs; p = 0.002). A mean of 6.2 {+-} 1.8 coils (n = 27) were used in the standard coil group, and 1.3 {+-} 0.9 coils (p < 0.0001) were used in the IDC group (n = 23) because additional pushable coils were required to achieve GDA occlusion in 4 patients. In 2 patients, the IDC could not be deployed through a Soft-VU catheter. One standard coil dislodged in the hepatic artery and was retrieved. Vessel reperfusion was noted in only 1 patient in the standard coil group. Controlled embolization of the GDA with fibered IDCs was achieved more rapidly than with pushable coils. However, vessel occlusion may not be obtained using a single device only, and the use of sharply angled guiding catheters hampered coil pushability.« less

Kinetic studies on strand displacement in de novo designed parallel heterodimeric coiled coils† †Electronic supplementary information (ESI) available. See DOI: 10.1039/c7sc05342h

PubMed Central

Groth, Mike C.; Rink, W. Mathis; Meyer, Nils F.

2018-01-01

Among the protein folding motifs, which are accessible by de novo design, the parallel heterodimeric coiled coil is most frequently used in bioinspired applications and chemical biology in general. This is due to the straightforward sequence-to-structure relationships, which it has in common with all coiled-coil motifs, and the heterospecificity, which allows control of association. Whereas much focus was laid on designing orthogonal coiled coils, systematic studies on controlling association, for instance by strand displacement, are rare. As a contribution to the design of dynamic coiled-coil-based systems, we studied the strand-displacement mechanism in obligate heterodimeric coiled coils to investigate the suitability of the dissociation constants (KD) as parameters for the prediction of the outcome of strand-displacement reactions. We use two sets of heterodimeric coiled coils, the previously reported N-AxBy and the newly characterized C-AxBy. Both comprise KD values in the μM to sub-nM regime. Strand displacement is explored by CD titration and a FRET-based kinetic assay and is proved to be an equilibrium reaction with half-lifes from a few seconds up to minutes. We could fit the displacement data by a competitive binding model, giving rate constants and overall affinities of the underlying association and dissociation reactions. The overall affinities correlate well with the ratios of KD values determined by CD-thermal denaturation experiments and, hence, support the dissociative mechanism of strand displacement in heterodimeric coiled coils. From the results of more than 100 different displacement reactions we are able to classify three categories of overall affinities, which allow for easy prediction of the equilibrium of strand displacement in two competing heterodimeric coiled coils. PMID:29780562

Comparison of pelvic phased-array versus endorectal coil magnetic resonance imaging at 3 Tesla for local staging of prostate cancer.

PubMed

Kim, Bum Soo; Kim, Tae-Hwan; Kwon, Tae Gyun; Yoo, Eun Sang

2012-05-01

Several studies have demonstrated the superiority of endorectal coil magnetic resonance imaging (MRI) over pelvic phased-array coil MRI at 1.5 Tesla for local staging of prostate cancer. However, few have studied which evaluation is more accurate at 3 Tesla MRI. In this study, we compared the accuracy of local staging of prostate cancer using pelvic phased-array coil or endorectal coil MRI at 3 Tesla. Between January 2005 and May 2010, 151 patients underwent radical prostatectomy. All patients were evaluated with either pelvic phased-array coil or endorectal coil prostate MRI prior to surgery (63 endorectal coils and 88 pelvic phased-array coils). Tumor stage based on MRI was compared with pathologic stage. We calculated the specificity, sensitivity and accuracy of each group in the evaluation of extracapsular extension and seminal vesicle invasion. Both endorectal coil and pelvic phased-array coil MRI achieved high specificity, low sensitivity and moderate accuracy for the detection of extracapsular extension and seminal vesicle invasion. There were statistically no differences in specificity, sensitivity and accuracy between the two groups. Overall staging accuracy, sensitivity and specificity were not significantly different between endorectal coil and pelvic phased-array coil MRI.

A history of detachable coils: 1987-2012.

PubMed

Hui, Ferdinand K; Fiorella, David; Masaryk, Thomas J; Rasmussen, Peter A; Dion, Jacques E

2014-03-01

The development of detachable coils is one of the most pivotal developments in neurointervention, providing a tool that could be used to treat a wide variety of hemorrhagic stroke. From the original Guglielmi detachable coil, a number of different coil designs and delivery designs have evolved. This article reviews the history of commercially available detachable coils. A timeline of detachable coils was constructed and coil design philosophies were reviewed. A complete list of commercially available coils is presented in a timeline format. Detachable coil technology continues to evolve. Advances in construction and design have yielded products which may benefit patients in terms of safety, radiation dose reduction and cost of treatment. Continued evolution is expected, irrespective of competing disruptive technologies.

Radio frequency coil technology for small-animal MRI.

PubMed

Doty, F David; Entzminger, George; Kulkarni, Jatin; Pamarthy, Kranti; Staab, John P

2007-05-01

A review of the theory, technology, and use of radio frequency (RF) coils for small-animal MRI is presented. It includes a brief overview of MR signal-to-noise (S/N) analysis and discussions of the various coils commonly used in small-animal MR: surface coils, linear volume coils, birdcages, and their derivatives. The scope is limited to mid-range coils, i.e. coils where the product (fd) of the frequency f and the coil diameter d is in the range 2-30 MHz-m. Common applications include mouse brain and body coils from 125 to 750 MHz, rat body coils up to 500 MHz, and small surface coils at all fields. In this regime, all the sources of loss (coil, capacitor, sample, shield, and transmission lines) are important. All such losses may be accurately captured in some modern full-wave 3D electromagnetics software, and new simulation results are presented for a selection of surface coils using Microwave Studio 2006 by Computer Simulation Technology, showing the dramatic importance of the "lift-off effect". Standard linear circuit simulators have been shown to be useful in optimization of complex coil tuning and matching circuits. There appears to be considerable potential for trading S/N for speed using phased arrays, especially for a larger field of view. Circuit simulators are shown to be useful for optimal mismatching of ultra-low-noise preamps based on the enhancement-mode pseudomorphic high-electron-mobility transistor for optimal coil decoupling in phased arrays. Cryogenically cooled RF coils are shown to offer considerable opportunity for future gains in S/N in smaller samples.

[Applied studies of structured triglycerides for parenteral nutrition in severe hemorrhagic shock patients after resuscitation].

PubMed

Su, Mao-sheng; He, Lei; Liu, Zhi-wei; Ma, Huan-xian; Zhao, Qing-hua; Zhang, Wen-zhi

2012-03-27

To evaluate the effects of structured triglycerides in parenteral nutrition versus a physical medium-chain triglycerides (MCT)/long-chain triglycerides (LCT) mixture on severe hemorrhagic shock patients after resuscitation. In a randomized trial, we studied 20 critical patients with a total blood loss of over 3000 ml perioperatively and/or intraoperatively. The use of triglycerides started from Day 3 postoperation and parenteral nutrition lasted for no less than 5 days. They were allocated to receive one of two nutrition regiments: structured triglycerides in Group A (n = 10) and MCT/LCT in Group B (n = 10). There were no significant differences of general conditions in two groups. Before the start of parenteral nutrition (d0), d1 d3 and d5 after start of infusion, the following parameters were measured: hemoglobin (Hb), platelet count (Plt), alanine aminotransferase (ALT), total bilirubin (TB), direct bilirubin (DB), serum triglycerides (TG), prealbumin (PA) and transferrin (TF). And mean artery pressure (MAP), heart rate (HR) and central vein pressure (CVP) were also recorded at the same time-points. Then the post-TG changes of the above data were compared in both groups. After the use of triglycerides, there were no significant differences of MAP, HR, CVP, Hb and Plt in both groups (P > 0.05). At D3 and D5, the serum levels of TG ((2.1 ± 0.4) vs (1.6 ± 0.6) mg/L, (2.3 ± 0.7) vs (1.5 ± 0.3) mg/L) and alanine aminotransferase ((133 ± 58) vs (97 ± 26) U/L; (116 ± 48) vs (77 ± 31) U/L) were significantly higher in Group B versus those receiving structured triglycerides in Group A (P < 0.05). TB ((18 ± 15) vs (18 ± 11) µmol/L) and DB ((8.9 ± 3.2) vs (8.8 ± 2.5) µmol/L) had no significant differences in two groups (P > 0.05). The serum levels of such nutrition markers as PA ((195 ± 55) vs (166 ± 55) mg/L,(245 ± 53) vs (195 ± 58) mg/L) and TF ((2.6 ± 0.5) vs (2.5 ± 0.6) g/L, (3.3 ± 0.8) vs (2.9 ± 0.6) g/L)were significantly higher in Group A than those in Group B (P < 0.05). With regards to lipid metabolism, protein synthesis and hepatocyte protection, structured triglycerides in parenteral nutrition is advantageous to standard MCT/LCT emulsion in severe hemorrhagic shock patients after resuscitation.

The hypertriglyceridemic clamp technique. Studies using long-chain and structured triglyceride emulsions in healthy subjects.

PubMed

Nordenström, Jörgen; Thörne, Anders; Aberg, Wiveca; Carneheim, Claes; Olivecrona, Thomas

2006-11-01

In a randomized crossover study, plasma kinetics of 2 different types of fat emulsions were studied in 8 healthy volunteers by using a hypertriglyceridemic clamp technique. The method involves the stabilization of serum triglyceride (TG) concentration during 180 minutes at a predetermined level (4 mmol/L) by adjustment of TG infusion rate by repeated online measurements of serum TG concentration. The fat emulsions under study were a long-chain fatty acid triglyceride (LCT) emulsion (Intralipid 20%, Fresenius Kabi, Sweden) and a structured triglyceride (STG) emulsion (Structolipid 20%, Fresenius Kabi) where medium- and long-chain fatty acids have been interesterified within a TG molecule. The hypertriglyceridemic clamp was found to have acceptable reproducibility when tested in 3 healthy individuals on 2 different occasions, as similar steady-state TG levels were obtained by infusing similar amounts of fat. The average (+/-SEM) TG concentration during the 180-minute clamp was similar for STGs and LCTs (4.0 +/- 0.1 vs 3.9 +/- 0.1 mmol/L; not significant), but the amount of fat that had to be infused was significantly higher during STG than during LCT clamping (0.31 +/- 0.04 vs 0.21 +/- 0.02 g TG per minute; P < .05). Higher serum levels of free fatty acids (1.80 +/- 0.13 vs 0.96 +/- 0.09 mmol/L; P < .05), free glycerol (1.30 +/- 0.07 vs 0.76 +/- 0.08 mmol/L; P < .001), and beta-OH butyrate (1.61 +/- 0.44 vs 1.17 +/- 0.23 mmol/L; not significant) were obtained at the end of the clamp during infusion of STGs compared with LCTs. During infusion of STGs the medium-chain fatty acids octanoic (C:8) and decanoic acid (C:10) constituted approximately half of circulating fatty acids that correspond to the compositional ratio of the emulsion. Plasma lipoprotein lipase (LPL) concentration was higher during STG than during LCT clamping (6.06 +/- 0.62 vs 3.15 +/- 0.40 mU/mL; P < .05), and there was a positive correlation between the mean LPL concentration and the amount of infused TG during the steady-state period (r = 0.58; P < .05). In conclusion, the hypertriglyceridemic clamp method was found to give reproducible results and could be considered for comparison of metabolic clearance properties of different types of fat emulsions. The capacity of healthy subjects to eliminate STGs from blood was greater than for LCTs. An increased LPL activity induced by the higher TG infusion rate may have contributed to the increased metabolic clearance of STGs.

A Synthetic Coiled-Coil Interactome Provides Heterospecific Modules for Molecular Engineering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reinke, Aaron W.; Grant, Robert A.; Keating, Amy E.

2010-06-21

The versatile coiled-coil protein motif is widely used to induce and control macromolecular interactions in biology and materials science. Yet the types of interaction patterns that can be constructed using known coiled coils are limited. Here we greatly expand the coiled-coil toolkit by measuring the complete pairwise interactions of 48 synthetic coiled coils and 7 human bZIP coiled coils using peptide microarrays. The resulting 55-member protein 'interactome' includes 27 pairs of interacting peptides that preferentially heteroassociate. The 27 pairs can be used in combinations to assemble sets of 3 to 6 proteins that compose networks of varying topologies. Of specialmore » interest are heterospecific peptide pairs that participate in mutually orthogonal interactions. Such pairs provide the opportunity to dimerize two separate molecular systems without undesired crosstalk. Solution and structural characterization of two such sets of orthogonal heterodimers provide details of their interaction geometries. The orthogonal pair, along with the many other network motifs discovered in our screen, provide new capabilities for synthetic biology and other applications.« less

Measurement of a Conduction Cooled Nb3Sn Racetrack Coil

NASA Astrophysics Data System (ADS)

Kim, HS; Kovacs, C.; Rochester, J.; Sumption, MD; Tomsic, M.; Peng, X.; Doll, D.

2017-12-01

Use of superconducting coils for wind turbines and electric aircraft is of interest because of the potential for high power density and weight reduction. Here we test a racetrack coil developed as a proof-of-concept for cryogen-free superconducting motors and generators. The coil was wound with 1209 m of 0.7-mm-diameter insulated tube-type Nb3Sn wire. The coil was epoxy-impregnated, instrumented, covered with numerous layers of aluminized mylar insulation, and inserted vertically into a dewar. The system was cooled to 4.2 K, and a few inches of liquid helium was allowed to collect at the bottom of the dewar but below the coil. The coil was cooled by conduction via copper cooling bars were attached to the coil but also were immersed in the liquid helium at their lower ends. Several current tests were performed on the coil, initially in voltage mode, and one run in current mode. The maximum coil Ic at 4.2 K was 480 A, generating 3.06 T at the surface of the coil. The coil met the design targets with a noticeable margin.

Measurement of Diffusion in Entangled Rod-Coil Triblock Copolymers

NASA Astrophysics Data System (ADS)

Olsen, B. D.; Wang, M.

2012-02-01

Although rod-coil block copolymers have attracted increasing attention for functional nanomaterials, their dynamics relevant to self-assembly and processing have not been widely investigated. Because the rod and coil blocks have different reptation behavior and persistence lengths, the mechanism by which block copolymers will diffuse is unclear. In order to understand the effect of the rigid block on reptation, tracer diffusion of a coil-rod-coil block copolymer through an entangled coil polymer matrix was experimentally measured. A monodisperse, high molecular weight coil-rod-coil triblock was synthesized using artificial protein engineering to prepare the helical rod and bioconjugaiton of poly(ethylene glycol) coils to produce the final triblock. Diffusion measurements were performed using Forced Rayleigh scattering (FRS), at varying ratios of the rod length to entanglement length, where genetic engineering is used to control the protein rod length and the polymer matrix concentration controls the entanglement length. As compared to PEO homopolymer tracers, the coil-rod-coil triblocks show markedly slower diffusion, suggesting that the mismatch between rod and coil reptation mechanisms results in hindered diffusion of these molecules in the entangled state.

Deep brain transcranial magnetic stimulation using variable "Halo coil" system

NASA Astrophysics Data System (ADS)

Meng, Y.; Hadimani, R. L.; Crowther, L. J.; Xu, Z.; Qu, J.; Jiles, D. C.

2015-05-01

Transcranial Magnetic Stimulation has the potential to treat various neurological disorders non-invasively and safely. The "Halo coil" configuration can stimulate deeper regions of the brain with lower surface to deep-brain field ratio compared to other coil configurations. The existing "Halo coil" configuration is fixed and is limited in varying the site of stimulation in the brain. We have developed a new system based on the current "Halo coil" design along with a graphical user interface system that enables the larger coil to rotate along the transverse plane. The new system can also enable vertical movement of larger coil. Thus, this adjustable "Halo coil" configuration can stimulate different regions of the brain by adjusting the position and orientation of the larger coil on the head. We have calculated magnetic and electric fields inside a MRI-derived heterogeneous head model for various positions and orientations of the coil. We have also investigated the mechanical and thermal stability of the adjustable "Halo coil" configuration for various positions and orientations of the coil to ensure safe operation of the system.

Apparatus for unilateral generation of a homogeneous magnetic field

DOEpatents

Fukushima, Eiichi; Rath, Alan R.; Roeder, Stephen B. W.

1988-01-01

An apparatus for unilaterally producing a substantially homogeneous magnetic field. The apparatus includes two circular electromagnet coils, a small coil and a large coil, which are coaxial with one another and which are separated by a distance equal to one-half the difference in the radius of the two coils. By appropriate selection of electrical currents, which are passed through the coil in opposite directions, a region of homogeneous magnetic field is formed. This region is centered on the common axis of the two coils, at a point on the axis which is at a distance from the small coil equal to one-half the radius of the small coil, and which is on the opposite side of the small coil from the large coil. The apparatus has particular application in the field of diagnostic medical NMR and other NMR applications.

Apparatus for unilateral generation of a homogeneous magnetic field

DOEpatents

Fukushima, E.; Rath, A.R.; Roeder, S.B.W.

1984-05-01

An apparatus for unilaterally producing a substantially homogeneous magnetic field. The apparatus includes two circular electromagnet coils, a small coil and a large coil, which are coaxial with one another and which are separated by a distance equal to one-half the difference in the radius of the two coils. By appropriate selection of electrical currents, which are passed through the coils in opposite directions, a region of homogeneous magnetic field is formed. This region is centered on the common axis of the two coils, at a point on the axis which is at a distance from the small coil equal to one-half the radius of the small coil, and which is on the opposite side of the small coil from the large coil. The apparatus has particular application in the field of diagnostic medical NMR and other NMR applications.

Aneurysm permeability following coil embolization: packing density and coil distribution.

PubMed

Chueh, Ju-Yu; Vedantham, Srinivasan; Wakhloo, Ajay K; Carniato, Sarena L; Puri, Ajit S; Bzura, Conrad; Coffin, Spencer; Bogdanov, Alexei A; Gounis, Matthew J

2015-09-01

Rates of durable aneurysm occlusion following coil embolization vary widely, and a better understanding of coil mass mechanics is desired. The goal of this study is to evaluate the impact of packing density and coil uniformity on aneurysm permeability. Aneurysm models were coiled using either Guglielmi detachable coils or Target coils. The permeability was assessed by taking the ratio of microspheres passing through the coil mass to those in the working fluid. Aneurysms containing coil masses were sectioned for image analysis to determine surface area fraction and coil uniformity. All aneurysms were coiled to a packing density of at least 27%. Packing density, surface area fraction of the dome and neck, and uniformity of the dome were significantly correlated (p<0.05). Hence, multivariate principal components-based partial least squares regression models were used to predict permeability. Similar loading vectors were obtained for packing and uniformity measures. Coil mass permeability was modeled better with the inclusion of packing and uniformity measures of the dome (r(2)=0.73) than with packing density alone (r(2)=0.45). The analysis indicates the importance of including a uniformity measure for coil distribution in the dome along with packing measures. A densely packed aneurysm with a high degree of coil mass uniformity will reduce permeability. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Radio-frequency coil selection for MR imaging of the carotid vessel wall

NASA Astrophysics Data System (ADS)

Mat Isa, S.; Shuaib, I. L.; Bauk, S.

2014-11-01

This aim of this study was to identify the radiofrequency coil that will produce optimum image quality for scanning the carotid vessel wall using magnetic resonance imaging. A comparative cross-sectional study was conducted using 10 volunteers. Each volunteer was scanned three times using a 1.5T Signa HDxt machine equipped with one of three different coils: a neurovascular array (NV) coil, an 8-channel CTL spine array coil, and a 3-inch surface coil. A qualitative image quality rating was assigned to each image. The images were also evaluated by measuring the signal to noise ratio (SNR) using Osirix 4.2.3 software. The noise was estimated from the mean intensities of the region of interest in the background of the images and the signal was measured in the muscle adjacent to the vessel wall. The SNRs of the three coils were compared using one-way ANOVA, with 104 images used for the data analysis. The mean image quality scores for the NV head coil, CTL coil, and 3-inch coil were 3.4, 3.33, and 1.67, respectively. In addition, the SNRs differed significantly (p < 0.05). The mean SNR for the 3-inch coil was significantly higher (56.21 ± 25.06) than those for the NV head coil (27.34 ± 15.47) and CTL coil (21.77 ± 13.14). The Bonferroni post-hoc test revealed that there was no significant difference between the NV head coil and the CTL coil (p = 0.21). The optimum SNR value was 20-27. These results indicate that the NV head coil and CTL coil can be used to evaluate the carotid arterial wall with optimum image quality and higher resolution. These coil can deliver fast and robust data to image the carotid vessel wall in vivo.

Application of a run around coil system to a roof fan house at Michoud Assembly Facility at New Orleans, Louisiana

NASA Technical Reports Server (NTRS)

1976-01-01

Analysis of the proposed run around coil system indicates that it offers a decrease in steam, electricity and water consumptions. The run around coil system consist of two coils, a precooling coil which will be located at up stream and a reheating coil which will be located at down stream of the chilled water spray chamber. This system will provide the necessary reheat in summer, spring and fall. At times, if the run around coil system can not provide the necessary reheat, the existing reheat coil could be utilized.

Effective arrangement of separated transmit-only/receive-only RF coil for improvement of B1 homogeneity at 7 Tesla

NASA Astrophysics Data System (ADS)

Im, Geun Ho; Seo, Jeong-Hoon; Kim, Kyoung-Nam; Heo, Phil; Chung, Julius Juhyun; Jang, Moon-Sun; Lee, Jung Hee; Kim, Jae-Hun; Kim, Sun I.

2014-09-01

This article presents an effective arrangement with shifted transmit (Tx)-only and receive (Rx)-only (TORO) radiofrequency (RF) coils in a single-channel surface coil for improving the magnetic flux ( B 1) homogeneity in an ultra-high field (UHF) magnetic resonance imaging (MRI) scanner. The proposed new methodology for the coil arrangement using the shifted TORO RF coils was demonstrated for coils with 50-mm, 100-mm, and 150-mm-square surfaces and the results were compared to those for general Tx/Rx surface coils with the same dimensions. The computational analysis indicated that a homogeneous B1 field was achieved when the Rx-only coil was shifted in the two-dimensional xy-plane away from the Tx-only coils. Because the proposed coil configuration provides a unique opportunity for increasing the B 1 homogeneity, this feature is likely to increase the feasibility via new coil arrangements of UHF surface design and fabrication.

New Side-Looking Rogowski Coil Sensor for Measuring Large-Magnitude Fast Impulse Currents

NASA Astrophysics Data System (ADS)

Metwally, I. A.

2015-12-01

This paper presents a new design of a side-looking "flat spiral" self-integrating Rogowski coil that is wound by twin coaxial cable with individual sheath. The coil is tested with different impulse current waveforms up to 7 kA peak value to improve its performance. The coil design is optimized to achieve bandwidth and sensitivity up to 7.854 MHz and 3.623 V/kA, respectively. The coil is calibrated versus two commercial impulse-current measurement devices at different coil-to-wire separations, coil inclination angles, and impulse current waveforms. Distortion of the coil output voltage waveform is examined by using the lumped-element model to optimize the connections of the four cable winding sheaths and the coil termination resistance. Finally, the coil frequency response is investigated to optimize the coil design parameters and achieve the desired bandwidth (large low-frequency time constant), high rate of rise, no overshoot, very small droop, high rate of fall, and no backswing.

Apparatus and Methods for Mitigating Electromagnetic Emissions

NASA Technical Reports Server (NTRS)

Geng, Steven M. (Inventor); Niedra, Janis M. (Inventor)

2013-01-01

Apparatus, methods, and other embodiments associated with mitigation of magnetic fields are described herein. In an embodiment, a method for mitigating an electromagnetic field includes positioning a mitigating coil around a linear alternator of linear motor so that the mitigating coil is coaxially located with an alternator coil; arranging the mitigating coil to generate a field to mitigate an electromagnetic field generated by the alternator coil; and passing an induced current from the alternator coil through the mitigating coil.

Apparatus and Methods for Mitigating Electromagnetic Emissions

NASA Technical Reports Server (NTRS)

Geng, Steven M. (Inventor); Niedra, Janis M. (Inventor)

2016-01-01

Apparatus, methods, and other embodiments associated with mitigation of magnetic fields are described herein. In an embodiment, a method for mitigating an electromagnetic field includes positioning a mitigating coil around a linear alternator of linear motor so that the mitigating coil is coaxially located with an alternator coil; arranging the mitigating coil to generate a field to mitigate an electromagnetic field generated by the alternator coil; and passing an induced current from the alternator coil through the mitigating coil.

Optimization and Validation of Rotating Current Excitation with GMR Array Sensors for Riveted

DTIC Science & Technology

2016-09-16

distribution. Simulation results, using both an optimized coil and a conventional coil, are generated using the finite element method (FEM) model...optimized coil and a conventional coil, are generated using the finite element method (FEM) model. The signal magnitude for an optimized coil is seen to be...optimized coil. 4. Model Based Performance Analysis A 3D finite element model (FEM) is used to analyze the performance of the optimized coil and

CCBuilder: an interactive web-based tool for building, designing and assessing coiled-coil protein assemblies.

PubMed

Wood, Christopher W; Bruning, Marc; Ibarra, Amaurys Á; Bartlett, Gail J; Thomson, Andrew R; Sessions, Richard B; Brady, R Leo; Woolfson, Derek N

2014-11-01

The ability to accurately model protein structures at the atomistic level underpins efforts to understand protein folding, to engineer natural proteins predictably and to design proteins de novo. Homology-based methods are well established and produce impressive results. However, these are limited to structures presented by and resolved for natural proteins. Addressing this problem more widely and deriving truly ab initio models requires mathematical descriptions for protein folds; the means to decorate these with natural, engineered or de novo sequences; and methods to score the resulting models. We present CCBuilder, a web-based application that tackles the problem for a defined but large class of protein structure, the α-helical coiled coils. CCBuilder generates coiled-coil backbones, builds side chains onto these frameworks and provides a range of metrics to measure the quality of the models. Its straightforward graphical user interface provides broad functionality that allows users to build and assess models, in which helix geometry, coiled-coil architecture and topology and protein sequence can be varied rapidly. We demonstrate the utility of CCBuilder by assembling models for 653 coiled-coil structures from the PDB, which cover >96% of the known coiled-coil types, and by generating models for rarer and de novo coiled-coil structures. CCBuilder is freely available, without registration, at http://coiledcoils.chm.bris.ac.uk/app/cc_builder/. © The Author 2014. Published by Oxford University Press.

A multi-slot surface coil for MRI of dual-rat imaging at 4 T

NASA Astrophysics Data System (ADS)

Solis, S. E.; Wang, R.; Tomasi, D.; Rodriguez, A. O.

2011-06-01

A slotted surface coil inspired by the hole-and-slot cavity magnetron was developed for magnetic resonance imaging of obese rats at 4 T. Full-wave analysis of the magnetic field was carried out at 170 MHz for both the slotted and circular-shaped coils. The noise figure values of two coils were investigated via the numerical calculation of the quality factors. Fat simulated phantoms to mimic overweight rats were included in the analysis with weights ranging from 300 to 900 g. The noise figures were 1.2 dB for the slotted coil and 2.4 dB for the circular coil when loaded with 600 g of simulated phantom. A slotted surface coil with eight circular slots and a circular coil with similar dimensions were built and operated in the transceiver mode, and their performances were experimentally compared. The imaging tests in phantoms demonstrated that the slotted surface coil has a deeper RF-sensitivity and better field uniformity than the single-loop RF-coil. High quality images of two overweight Zucker rats were acquired simultaneously with the slotted surface coil using standard spin-echo pulse sequences. Experimental results showed that the slotted surface coil outperformed the circular coil for imaging considerably overweight rats. Thus, the slotted surface coil can be a good tool for MRI experiments in rats on a human whole-body 4 T scanner.

Shielded helix traveling wave cathode ray tube deflection structure

DOEpatents

Norris, Neil J.; Hudson, Charles L.

1992-01-01

Various embodiments of a helical coil deflection structure of a CRT are described and illustrated which provide shielding between adjacent turns of the coil on either three or four sides of each turn in the coil. Threaded members formed with either male or female threads and having the same pitch as the deflection coil are utilized for shielding the deflection coil with each turn of the helical coil placed between adjacent threads which act to shield each coil turn from adjacent turns and to confine the field generated by the coil to prevent or inhibit cross-coupling between adjacent turns of the coil to thereby prevent generation of fast fields which might otherwise deflect the beam out of time synchronization with the electron beam pulse.

Toroidal plasma response based ELM control coil design for EU DEMO

NASA Astrophysics Data System (ADS)

Zhou, Lina; Liu, Yueqiang; Wenninger, Ronald; Liu, Yue; Wang, Shuo; Yang, Xu

2018-07-01

Magnetic coil design study is carried out, for the purpose of mitigating or suppressing the edge localized modes (ELMs) in a EU DEMO reference scenario. The coil design, including both the coil geometry and the coil current requirement, is based on criteria derived from the linear, full toroidal plasma response computed by the MARS-F code (Liu et al 2000 Phys. Plasma 7 3681). With a single midplane row of coils, a coil size covering about 30°–50° poloidal angle of the torus is found to be optimal for ELM control using the n  >  2 resonant magnetic perturbation (RMP) field (n is the toroidal mode number). For off-midplane coils, the coils’ poloidal location, as well as the relative toroidal phase (coil phasing) between the upper and lower rows of coils, also sensitively affects the ELM control according to the specified criteria. Assuming that the optimal coil phasing can always be straightforwardly implemented, following a simple analytic model derived from toroidal computations, it is better to place the two off-midplane rows of coils near the midplane, in order to maximize the resonant field amplitude and to have larger effects on ELMs. With the same coil current, the ex-vessel coils can be made as effective as the in-vessel coils, at the expense of increasing the ex-vessel coils’ size. This is however possible only for low-n (n  =  1–3) RMP fields. With these low-n fields, and assuming 300 kAt maximal coil current, the computed plasma displacement near the X-point can meet the 10 mm level, which we use as the conservative indicator for achieving ELM mitigation in EU DEMO. The risk of partial control coil failure in EU DEMO is also assessed based on toroidal modeling, indicating that the large n  =  1 sideband due to coil failure may need to be corrected, if the nominal n  >  1 coil configurations are used for ELM control in EU DEMO.

The contactless detection of local normal transitions in superconducting coils by using Poynting’s vector method

NASA Astrophysics Data System (ADS)

Habu, K.; Kaminohara, S.; Kimoto, T.; Kawagoe, A.; Sumiyoshi, F.; Okamoto, H.

2010-11-01

We have developed a new monitoring system to detect an unusual event in the superconducting coils without direct contact on the coils, using Poynting's vector method. In this system, the potential leads and pickup coils are set around the superconducting coils to measure local electric and magnetic fields, respectively. By measuring the sets of magnetic and electric fields, the Poynting's vectors around the coil can be obtained. An unusual event in the coil can be detected as the result of the change of the Poynting's vector. This system has no risk of the voltage breakdown which may happen with the balance voltage method, because there is no need of direct contacts on the coil windings. In a previous paper, we have demonstrated that our system can detect the normal transitions in the Bi-2223 coil without direct contact on the coil windings by using a small test system. For our system to be applied to practical devices, it is necessary for the early detection of an unusual event in the coils to be able to detect local normal transitions in the coils. The signal voltages of the small sensors to measure local magnetic and electric fields are small. Although the increase in signals of the pickup coils is attained easily by an increase in the number of turns of the pickup coils, an increase in the signals of the potential lead is not easily attained. In this paper, a new method to amplify the signal of local electric fields around the coil is proposed. The validity of the method has been confirmed by measuring local electric fields around the Bi-2223 coil.

Inductively coupled wireless RF coil arrays.

PubMed

Bulumulla, S B; Fiveland, E; Park, K J; Foo, T K; Hardy, C J

2015-04-01

As the number of coils increases in multi-channel MRI receiver-coil arrays, RF cables and connectors become increasingly bulky and heavy, degrading patient comfort and slowing workflow. Inductive coupling of signals provides an attractive "wireless" approach, with the potential to reduce coil weight and cost while simplifying patient setup. In this work, multi-channel inductively coupled anterior arrays were developed and characterized for 1.5T imaging. These comprised MR receiver coils inductively (or "wirelessly") linked to secondary or "sniffer" coils whose outputs were transmitted via preamps to the MR system cabinet. The induced currents in the imaging coils were blocked by passive diode circuits during RF transmit. The imaging arrays were totally passive, obviating the need to deliver power to the coils, and providing lightweight, untethered signal reception with easily positioned coils. Single-shot fast spin echo images were acquired from 5 volunteers using a 7-element inductively coupled coil array and a conventionally cabled 7-element coil array of identical geometry, with the inductively-coupled array showing a relative signal-to-noise ratio of 0.86 +/- 0.07. The concept was extended to a larger 9-element coil array to demonstrate the effect of coil element size on signal transfer and RF-transmit blocking. Copyright © 2015 Elsevier Inc. All rights reserved.

Periprocedural safety of aneurysm embolization with the Medina Coil System: the early human experience.

PubMed

Turk, Aquilla S; Maia, Orlando; Ferreira, Christian Candido; Freitas, Diogo; Mocco, J; Hanel, Ricardo

2016-02-01

Intracranial saccular aneurysms, if untreated, carry a high risk of morbidity and mortality from intracranial bleeding. Embolization coils are the most common treatment. We describe the periprocedural safety and performance of the initial human experience with the next generation Medina Coil System. The Medina Coil System is a layered three-dimensional coil made from a radiopaque, shape set core wire, and shape memory alloy outer coil filaments. Nine aneurysms in five patients were selected for treatment with the Medina Coil System. Nine aneurysms in five patients, ranging from 5 to 17 mm in size in various locations, were treated with the Medina Coil System. No procedural or periprocedural complications were encountered. Procedure times, number of coils used to treat the aneurysm, and use of adjunctive devices were much less than anticipated if conventional coil technology had been used. The Medina Coil System is a next generation coil that combines all of the familiar and expected procedural safety and technique concepts associated with conventional coils. We found improved circumferential aneurysm filling, which may lead to improved long term outcomes, with fewer devices and faster operating times. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Comparison of Pelvic Phased-Array versus Endorectal Coil Magnetic Resonance Imaging at 3 Tesla for Local Staging of Prostate Cancer

PubMed Central

Kim, Bum Soo; Kim, Tae-Hwan; Kwon, Tae Gyun

2012-01-01

Purpose Several studies have demonstrated the superiority of endorectal coil magnetic resonance imaging (MRI) over pelvic phased-array coil MRI at 1.5 Tesla for local staging of prostate cancer. However, few have studied which evaluation is more accurate at 3 Tesla MRI. In this study, we compared the accuracy of local staging of prostate cancer using pelvic phased-array coil or endorectal coil MRI at 3 Tesla. Materials and Methods Between January 2005 and May 2010, 151 patients underwent radical prostatectomy. All patients were evaluated with either pelvic phased-array coil or endorectal coil prostate MRI prior to surgery (63 endorectal coils and 88 pelvic phased-array coils). Tumor stage based on MRI was compared with pathologic stage. We calculated the specificity, sensitivity and accuracy of each group in the evaluation of extracapsular extension and seminal vesicle invasion. Results Both endorectal coil and pelvic phased-array coil MRI achieved high specificity, low sensitivity and moderate accuracy for the detection of extracapsular extension and seminal vesicle invasion. There were statistically no differences in specificity, sensitivity and accuracy between the two groups. Conclusion Overall staging accuracy, sensitivity and specificity were not significantly different between endorectal coil and pelvic phased-array coil MRI. PMID:22476999

A study on geometry effect of transmission coil for micro size magnetic induction coil

NASA Astrophysics Data System (ADS)

Lee, Kyung Hwa; Jun, Byoung Ok; Kim, Seunguk; Lee, Gwang Jun; Ryu, Mingyu; Choi, Ji-Woong; Jang, Jae Eun

2016-05-01

The effects of transmission (Tx) coil structure have been studied for micro-size magnetic induction coil. The size of the receiving (Rx) coil should be shrunk to the micrometer level for the various new applications such as micro-robot and wireless body implanted devices. In case of the macro-scale magnetic induction coil, the power transmission efficiency is generally considered to be higher as the inductance of the transmission coil became larger; however, the large size difference between macro-size Tx coil and micro-size Rx coil can decrease the power transmission efficiency due to the difference of resonance frequency. Here, we study a correlation of the power transmission with the size and distance between the macro-size Tx and micro-size Rx coils using magnetic induction technique. The maximum power efficiency was 0.28/0.23/0.13/0.12% at the distance of 0.3/1/3/5 cm between Rx and Tx coil. In addition, more efficient wireless power transferring method is suggested with a floating coil for the body implantable devices. The voltage output increased up to 5.4 mV than the original one Tx coil system. The results demonstrated the foundational wireless power transferring system with enhanced power efficiency.

Overview of torus magnet coil production at Fermilab for the Jefferson Lab 12-GeV Hall B upgrade

DOE PAGES

Krave, S.; Velev, G.; Makarov, A.; ...

2016-02-29

Fermi National Accelerator Laboratory (Fermilab) fabricated the torus magnet coils for the 12-GeV Hall B upgrade at Jefferson Lab (JLab). The production consisted of six large superconducting coils for the magnet and two spare coils. The toroidal field coils are approximately 2 m × 4 m × 5 cm thick. Each of these coils consists of two layers, each of which has 117 turns of copper-stabilized superconducting cable, which will be conduction cooled by supercritical helium. Due to the size of the coils and their unique geometry, Fermilab designed and fabricated specialized tooling and, together with JLab, developed unique manufacturingmore » techniques for each stage of the coil construction. Furthermore, this paper describes the tooling and manufacturing techniques required to produce the six production coils and the two spare coils needed by the project.« less

Buried polar residues in coiled-coil interfaces.

PubMed

Akey, D L; Malashkevich, V N; Kim, P S

2001-05-29

Coiled coils, estimated to constitute 3-5% of the encoded residues in most genomes, are characterized by a heptad repeat, (abcdefg)(n), where the buried a and d positions form the interface between multiple alpha-helices. Although generally hydrophobic, a substantial fraction ( approximately 20%) of these a- and d-position residues are polar or charged. We constructed variants of the well-characterized coiled coil GCN4-p1 with a single polar residue (Asn, Gln, Ser, or Thr) at either an a or a d position. The stability and oligomeric specificity of each variant were measured, and crystal structures of coiled-coil trimers with threonine or serine at either an a or a d position were determined. The structures show how single polar residues in the interface affect not only local packing, but also overall coiled-coil geometry as seen by changes in the Crick supercoil parameters and core cavity volumes.

Analysis and quantification of endovascular coil distribution inside saccular aneurysms using histological images.

PubMed

Morales, Hernán G; Larrabide, Ignacio; Geers, Arjan J; Dai, Daying; Kallmes, David F; Frangi, Alejandro F

2013-11-01

Endovascular coiling is often performed by first placing coils along the aneurysm wall to create a frame and then by filling up the aneurysm core. However, little attention has been paid to quantifying this filling strategy and to see how it changes for different packing densities. The purpose of this work is to analyze and quantify endovascular coil distribution inside aneurysms based on serial histological images of experimental aneurysms. Seventeen histological images from 10 elastase-induced saccular aneurysms in rabbits treated with coils were studied. In-slice coil density, defined as the area taken up by coil winds, was calculated on each histological image. Images were analyzed by partitioning the aneurysm along its longitudinal and radial axes. Coil distribution was quantified by measuring and comparing the in-slice coil density of each partition. Mean total in-slice coil density was 22.0 ± 6.2% (range 10.1-30.2%). The density was non-significantly different (p = 0.465) along the longitudinal axis. A significant difference (p < 0.001) between peripheral and core densities was found. Additionally, the peripheral-core density ratio was observed to be inversely proportional to the total in-slice coil density (R(2)=0.57, p <0.001). This ratio was near unity for high in-slice coil density (around 30%). These findings demonstrate and confirm that coils tend to be located near the aneurysm periphery when few are inserted. However, when more coils are added, the radial distribution becomes more homogeneous. Coils are homogeneously distributed along the longitudinal axis.

Retreatment of Recurrent Internal Carotid-Posterior Communicating Artery Aneurysm after Coil Embolization

PubMed Central

TOYOTA, Shingo; TAKI, Takuyu; WAKAYAMA, Akatsuki; YOSHIMINE, Toshiki

2015-01-01

Internal carotid-posterior communicating artery (IC-PC) aneurysms account for more than 20% of all intracranial aneurysms. As a result of the increase in coiling, there has also been an increase in recurrent IC-PC aneurysms after coiling. We present our experience of 10 recurrent IC-PC aneurysms after coiling that were retreated using surgical or endovascular techniques in order to discuss the choice of treatment and the points of clipping without removal of coils. From 2007 to 2014, 10 recurrent IC-PC aneurysms after coiling were retreated. When the previous frames covered the aneurysms all around or almost around except a part of the neck, coiling was chosen. In other cases, clipping was chosen. Clipping was attempted without removal of coils when it was technically feasible. Among the 10 IC-PC aneurysms retreated, 3 were retreated with coiling and 7 were retreated with clipping. In all three cases retreated with coiling, almost complete occlusion was accomplished. In the seven cases retreated with clipping, coil extrusion was observed during surgery in six cases. In most of them, it was necessary to dissect strong adhesions around the coiled aneurysms and to utilize temporary occlusion of the internal carotid artery. In all seven cases, neck clipping was accomplished without the removal of coils. There were no neurological complications in any cases. The management of recurrent lesions of embolized IC-PC aneurysms requires appropriate choice of treatment using both coiling and clipping. Clipping, especially without the removal of coils, plays an important role in safe treatment. PMID:26437796

Retreatment of Recurrent Internal Carotid-Posterior Communicating Artery Aneurysm after Coil Embolization.

PubMed

Toyota, Shingo; Taki, Takuyu; Wakayama, Akatsuki; Yoshimine, Toshiki

2015-01-01

Internal carotid-posterior communicating artery (IC-PC) aneurysms account for more than 20% of all intracranial aneurysms. As a result of the increase in coiling, there has also been an increase in recurrent IC-PC aneurysms after coiling. We present our experience of 10 recurrent IC-PC aneurysms after coiling that were retreated using surgical or endovascular techniques in order to discuss the choice of treatment and the points of clipping without removal of coils. From 2007 to 2014, 10 recurrent IC-PC aneurysms after coiling were retreated. When the previous frames covered the aneurysms all around or almost around except a part of the neck, coiling was chosen. In other cases, clipping was chosen. Clipping was attempted without removal of coils when it was technically feasible. Among the 10 IC-PC aneurysms retreated, 3 were retreated with coiling and 7 were retreated with clipping. In all three cases retreated with coiling, almost complete occlusion was accomplished. In the seven cases retreated with clipping, coil extrusion was observed during surgery in six cases. In most of them, it was necessary to dissect strong adhesions around the coiled aneurysms and to utilize temporary occlusion of the internal carotid artery. In all seven cases, neck clipping was accomplished without the removal of coils. There were no neurological complications in any cases. The management of recurrent lesions of embolized IC-PC aneurysms requires appropriate choice of treatment using both coiling and clipping. Clipping, especially without the removal of coils, plays an important role in safe treatment.

Wireless power transmission for battery charging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mi, Chris; Li, Siqi; Nguyen, Trong-Duy

A wireless power transmission system is provided for high power applications. The power transmission system is comprised generally of a charging unit configured to generate an alternating electromagnetic field and a receive unit configured to receive the alternating electromagnetic field from the charging unit. The charging unit includes a power source; an input rectifier; an inverter; and a transmit coil. The transmit coil has a spirangle arrangement segmented into n coil segments with capacitors interconnecting adjacent coil segments. The receive unit includes a receive coil and an output rectifier. The receive coil also has a spirangle arrangement segmented into mmore » coil segments with capacitors interconnecting adjacent coil segments.« less

Fifty years of coiled-coils and alpha-helical bundles: a close relationship between sequence and structure.

PubMed

Parry, David A D; Fraser, R D Bruce; Squire, John M

2008-09-01

alpha-Helical coiled coils are remarkable for the diversity of related conformations that they adopt in both fibrous and globular proteins, and for the range of functions that they exhibit. The coiled coils are based on a heptad (7-residue), hendecad (11-residue) or a related quasi-repeat of apolar residues in the sequences of the alpha-helical regions involved. Most of these, however, display one or more sequence discontinuities known as stutters or stammers. The resulting coiled coils vary in length, in the number of chains participating, in the relative polarity of the contributing alpha-helical regions (parallel or antiparallel), and in the pitch length and handedness of the supercoil (left- or right-handed). Functionally, the concept that a coiled coil can act only as a static rod is no longer valid, and the range of roles that these structures have now been shown to exhibit has expanded rapidly in recent years. An important development has been the recognition that the delightful simplicity that exists between sequence and structure, and between structure and function, allows coiled coils with specialized features to be designed de novo.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fabbricatore, P.; Ambrosio, G.; Cheban, S.

The Mu2e Transport Solenoid consists of 52 coils arranged in 27 coil modules that form the S-shaped cold mass. Each coil is wound from Al-stabilized NbTi superconductor. The coils are supported by an external structural aluminum shell machined from a forged billet. Most of the coil modules house two coils, with the axis of each coil oriented at an angle of approximately 5° with respect to each other. The coils are indirectly cooled with LHe circulating in tubes welded on the shell. In order to enhance the cooling capacity, pure aluminum sheets connect the inner bore of the coils tomore » the cooling tubes. The coils are placed inside the shell by the means of a shrink-fit procedure. A full-size prototype, with all the features of the full assembly, was successfully manufactured in a collaboration between INFN Genova and Fermilab. In order to ensure an optimal mechanical prestress at the coil-shell interface, the coils are inserted into the shell through a shrink-fitting process. We present the details of the prototype with the design choices as validated by the structural analysis. In conclusion, the fabrication steps are described as well.« less

Mu2e transport solenoid prototype design and manufacturing

DOE PAGES

Fabbricatore, P.; Ambrosio, G.; Cheban, S.; ...

2016-02-08

The Mu2e Transport Solenoid consists of 52 coils arranged in 27 coil modules that form the S-shaped cold mass. Each coil is wound from Al-stabilized NbTi superconductor. The coils are supported by an external structural aluminum shell machined from a forged billet. Most of the coil modules house two coils, with the axis of each coil oriented at an angle of approximately 5° with respect to each other. The coils are indirectly cooled with LHe circulating in tubes welded on the shell. In order to enhance the cooling capacity, pure aluminum sheets connect the inner bore of the coils tomore » the cooling tubes. The coils are placed inside the shell by the means of a shrink-fit procedure. A full-size prototype, with all the features of the full assembly, was successfully manufactured in a collaboration between INFN Genova and Fermilab. In order to ensure an optimal mechanical prestress at the coil-shell interface, the coils are inserted into the shell through a shrink-fitting process. We present the details of the prototype with the design choices as validated by the structural analysis. In conclusion, the fabrication steps are described as well.« less

Performance of the Conduction-Cooled LDX Levitation Coil

NASA Astrophysics Data System (ADS)

Michael, P. C.; Schultz, J. H.; Smith, B. A.; Titus, P. H.; Radovinsky, A.; Zhukovsky, A.; Hwang, K. P.; Naumovich, G. J.; Camille, R. J.

2004-06-01

The Levitated Dipole Experiment (LDX) was developed to study plasma confinement in a dipole magnetic field. Plasma is confined in the magnetic field of a 680-kg Nb3Sn Floating Coil (F-coil) that is electromagnetically supported at the center of a 5-m diameter by 3-m tall vacuum chamber. The Levitation Coil (L-coil) is a 2800-turn, double pancake winding that supports the weight of the F-coil and controls its vertical position within the vacuum chamber. The use of high-temperature superconductor (HTS) Bi-2223 for the L-coil minimizes the electrical and cooling power needed for levitation. The L-coil winding pack and support plate are suspended within the L-coil cryostat and cooled by conduction to a single-stage cryocooler rated for 25-W heat load at approximately 20 K. The coil current leads consist of conduction-cooled copper running from room temperature to 80 K and a pair of commercially-available, 150-A HTS leads. An automatically filled liquid-nitrogen reservoir provides cooling for the coil's radiation shield and for the leads' 80-K heat stations. This paper discusses the L-coil system design and its observed cryogenic performance.

Measurement of heating coil temperature for e-cigarettes with a “top-coil” clearomizer

PubMed Central

Wang, Ping; Ito, Kazuhide; Fowles, Jeff; Shusterman, Dennis; Jaques, Peter A.; Kumagai, Kazukiyo

2018-01-01

Objectives To determine the effect of applied power settings, coil wetness conditions, and e-liquid compositions on the coil heating temperature for e-cigarettes with a “top-coil” clearomizer, and to make associations of coil conditions with emission of toxic carbonyl compounds by combining results herein with the literature. Methods The coil temperature of a second generation e-cigarette was measured at various applied power levels, coil conditions, and e-liquid compositions, including (1) measurements by thermocouple at three e-liquid fill levels (dry, wet-through-wick, and full-wet), three coil resistances (low, standard, and high), and four voltage settings (3–6 V) for multiple coils using propylene glycol (PG) as a test liquid; (2) measurements by thermocouple at additional degrees of coil wetness for a high resistance coil using PG; and (3) measurements by both thermocouple and infrared (IR) camera for high resistance coils using PG alone and a 1:1 (wt/wt) mixture of PG and glycerol (PG/GL). Results For single point thermocouple measurements with PG, coil temperatures ranged from 322 ‒ 1008°C, 145 ‒ 334°C, and 110 ‒ 185°C under dry, wet-through-wick, and full-wet conditions, respectively, for the total of 13 replaceable coil heads. For conditions measured with both a thermocouple and an IR camera, all thermocouple measurements were between the minimum and maximum across-coil IR camera measurements and equal to 74% ‒ 115% of the across-coil mean, depending on test conditions. The IR camera showed details of the non-uniform temperature distribution across heating coils. The large temperature variations under wet-through-wick conditions may explain the large variations in formaldehyde formation rate reported in the literature for such “top-coil” clearomizers. Conclusions This study established a simple and straight-forward protocol to systematically measure e-cigarette coil heating temperature under dry, wet-through-wick, and full-wet conditions. In addition to applied power, the composition of e-liquid, and the devices’ ability to efficiently deliver e-liquid to the heating coil are important product design factors effecting coil operating temperature. Precautionary temperature checks on e-cigarettes under manufacturer-recommended normal use conditions may help to reduce the health risks from exposure to toxic carbonyl emissions associated with coil overheating. PMID:29672571

Tx/Rx Head Coil Induces Less RF Transmit-Related Heating than Body Coil in Conductive Metallic Objects Outside the Active Area of the Head Coil

PubMed Central

Nagy, Zoltan; Oliver-Taylor, Aaron; Kuehne, Andre; Goluch, Sigrun; Weiskopf, Nikolaus

2017-01-01

The transmit–receive (Tx/Rx) birdcage head coil is often used for excitation instead of the body coil because of the presumably lower risk of heating in and around conductive implants. However, this common practice has not been systematically tested. To investigate whether the Tx/Rx birdcage head coil produces less heating than the body coil when scanning individuals with implants, we used a 3T clinical scanner and made temperature measurements around a straight 15 cm conductor using either the Tx/Rx body or the head coil for excitation. Additionally, the transmitted fields of a Tx/Rx head coil were measured both in air and in gel using a resonant and a non-resonant B field probes as well as a non-resonant E field probe. Simulations using a finite-difference time domain solver were compared with the experimental findings. When the body coil was used for excitation, we observed heating around the 15 cm wire at various anatomical locations (both within and outside of the active volume of the head coil). Outside its active area, no such heating was observed while using the Tx/Rx head coil for excitation. The E and B fields of the Tx/Rx birdcage head coil extended well-beyond the physical dimensions of the coil. In air, the fields were monotonically decreasing, while in gel they were more complex with local maxima at the end of the ASTM phantom. These experimental findings were line with the simulations. While caution must always be exercised when scanning individuals with metallic implants, these findings support the use of the Tx/Rx birdcage head coil in place of the body coil at 3T in order to reduce the risk of heating in and around conductive implants that are remote from the head coil. PMID:28184184

Shielded helix traveling wave cathode ray tube deflection structure

DOEpatents

Norris, N.J.; Hudson, C.L.

1992-12-15

Various embodiments of a helical coil deflection structure of a CRT are described and illustrated which provide shielding between adjacent turns of the coil on either three or four sides of each turn in the coil. Threaded members formed with either male or female threads and having the same pitch as the deflection coil are utilized for shielding the deflection coil with each turn of the helical coil placed between adjacent threads which act to shield each coil turn from adjacent turns and to confine the field generated by the coil to prevent or inhibit cross-coupling between adjacent turns of the coil to thereby prevent generation of fast fields which might otherwise deflect the beam out of time synchronization with the electron beam pulse. 13 figs.

Helicopter Structures - A Review of Loads, Fatigue Design Techniques and Usage Monitoring

DTIC Science & Technology

1993-05-01

public release.L E LCT E NJUL Z23 1991n V COMMONWEALTH OF AUSTRALIA 1993 MAY 1993 •7 22 O 6, Ii This work Is copyright. Apart from any fair dealing...test results 31 21. Reduction factors used on the mean S-N curve to create a working S-N curve 32 22. Various cycle counting methods 37 23. The...state that the loading is essentially static. Strictly, this is true only for a perfectly balanced , isolated rotor in a no- wind condition. For a real

Medical Entomology Studies - XV. A Revision of the Subgenus Paraedes of the Genus Aedes (Diptera: Culicidae)

DTIC Science & Technology

1981-01-01

does not display a currently valid OMB control number. 1. REPORT DATE 1981 2. REPORT TYPE 3. DATES COVERED 00-00-1981 to 00-00-1981 4. TITLE AND...branched; 9-CT longer than 8-CT. Respiratory trumpet. Index 3.21-6.31. Metanotal plate. Seta ll-CT single, occasionally barbed, longer than 10, 12...figured and recorded (Table 1). Cephalothorax. Seta l-CT with 3-5 branches. Respiratory trumpet. Index 3.73-5.25, mean 4.53. Abdomen. Seta l-11 with 14

Inefficient Mechanical Transmission of Langat (Tick-Borne Encephalitis Virus Complex) Virus by Blood-Feeding Mites (Acari) to Laboratory Mice

DTIC Science & Technology

1993-05-01

AD--A269 706 SPSSHORT C:OMMNUNICATION 8 Inefficient Mechanical Transmission of Langat (Tick-Bornee Encephalitis Virus Complex) Virus by Blood-Feeding...I d after a . iremic blood meal. but onhv immediatelIy after the vi re muo. LANGAT (LGT) VIRUS is a member of the tick- No isolations of LCT virus...Use of ulatus collected in the Ulu Langat Forest re- Laboratory Animals." as promulgated by the Committee on serve, Malaysia. in l959’(Struth 1956

A combined solenoid-surface RF coil for high-resolution whole-brain rat imaging on a 3.0 Tesla clinical MR scanner.

PubMed

Underhill, Hunter R; Yuan, Chun; Hayes, Cecil E

2010-09-01

Rat brain models effectively simulate a multitude of human neurological disorders. Improvements in coil design have facilitated the wider utilization of rat brain models by enabling the utilization of clinical MR scanners for image acquisition. In this study, a novel coil design, subsequently referred to as the rat brain coil, is described that exploits and combines the strengths of both solenoids and surface coils into a simple, multichannel, receive-only coil dedicated to whole-brain rat imaging on a 3.0 T clinical MR scanner. Compared with a multiturn solenoid mouse body coil, a 3-cm surface coil, a modified Helmholtz coil, and a phased-array surface coil, the rat brain coil improved signal-to-noise ratio by approximately 72, 61, 78, and 242%, respectively. Effects of the rat brain coil on amplitudes of static field and radiofrequency field uniformity were similar to each of the other coils. In vivo, whole-brain images of an adult male rat were acquired with a T(2)-weighted spin-echo sequence using an isotropic acquisition resolution of 0.25 x 0.25 x 0.25 mm(3) in 60.6 min. Multiplanar images of the in vivo rat brain with identification of anatomic structures are presented. Improvement in signal-to-noise ratio afforded by the rat brain coil may broaden experiments that utilize clinical MR scanners for in vivo image acquisition. 2010 Wiley-Liss, Inc.

Extended Monopole antenna Array with individual Shield (EMAS) coil: An improved monopole antenna design for brain imaging at 7 tesla MRI.

PubMed

Woo, Myung-Kyun; Hong, Suk-Min; Lee, Jongho; Kang, Chang-Ki; Park, Sung-Yeon; Son, Young-Don; Kim, Young-Bo; Cho, Zang-Hee

2016-06-01

To propose a new Extended Monopole antenna Array with individual Shields (EMAS) coil that improves the B1 field coverage and uniformity along the z-direction. To increase the spatial coverage of Monopole antenna Array (MA) coil, each monopole antenna was shielded and extended in length. Performance of this new coil, which is referred to as EMAS coil, was compared with the original MA coil and an Extended Monopole antenna Array coil with no shield (EMA). For comparison, flip angle, signal-to-noise ratio (SNR), and receive sensitivity maps were measured at multiple regions of interest (ROIs) in the brain. The EMAS coil demonstrated substantially larger flip angle and receive sensitivity than the MA and EMA coils in the inferior aspect of the brain. In the brainstem ROI, for example, the flip angle in the EMAS coil was increased by 45.5% (or 60.0%) and the receive sensitivity was increased by 26.9% (or 14.9%), resulting in an SNR gain of 84.8% (or 76.3%) when compared with the MA coil (or EMA). The EMAS coil provided 25.7% (or 24.4%) more uniform B1+ field distribution compared with the MA (or EMA) coil in sagittal. The EMAS coil successfully extended the imaging volume in lower part of the brain. Magn Reson Med 75:2566-2572, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

Quantitative Evaluation of Performance in Interventional Neuroradiology: An Integrated Curriculum Featuring Theoretical and Practical Challenges

PubMed Central

Ernst, Marielle; Kriston, Levente; Romero, Javier M.; Frölich, Andreas M.; Jansen, Olav; Fiehler, Jens; Buhk, Jan-Hendrik

2016-01-01

Purpose We sought to develop a standardized curriculum capable of assessing key competencies in Interventional Neuroradiology by the use of models and simulators in an objective, quantitative, and efficient way. In this evaluation we analyzed the associations between the practical experience, theoretical knowledge, and the skills lab performance of interventionalists. Materials and Methods We evaluated the endovascular skills of 26 participants of the Advanced Course in Endovascular Interventional Neuroradiology of the European Society of Neuroradiology with a set of three tasks (aneurysm coiling and thrombectomy in a virtual simulator and placement of an intra-aneurysmal flow disruptor in a flow model). Practical experience was assessed by a survey. Participants completed a written and oral examination to evaluate theoretical knowledge. Bivariate and multivariate analyses were performed. Results In multivariate analysis knowledge of materials and techniques in Interventional Neuroradiology was moderately associated with skills in aneurysm coiling and thrombectomy. Experience in mechanical thrombectomy was moderately associated with thrombectomy skills, while age was negatively associated with thrombectomy skills. We found no significant association between age, sex, or work experience and skills in aneurysm coiling. Conclusion Our study gives an example of how an integrated curriculum for reasonable and cost-effective assessment of key competences of an interventional neuroradiologist could look. In addition to traditional assessment of theoretical knowledge practical skills are measured by the use of endovascular simulators yielding objective, quantitative, and constructive data for the evaluation of the current performance status of participants as well as the evolution of their technical competency over time. PMID:26848840

Coil Welding Aid

NASA Technical Reports Server (NTRS)

Wiesenbach, W. T.; Clark, M. C.

1983-01-01

Positioner holds coil inside cylinder during tack welding. Welding aid spaces turns of coil inside cylinder and applies contact pressure while coil is tack-welded to cylinder. Device facilitates fabrication of heat exchangers and other structures by eliminating hand-positioning and clamping of individual coil turns.

Nylon screws make inexpensive coil forms

NASA Technical Reports Server (NTRS)

Aucoin, G.; Rosenthal, C.

1978-01-01

Standard nylon screws act as coil form copper wire laid down in spiral thread. Completed coil may be bonded to printed-circuit board. However, it is impossible to tune coil by adjusting spacing between windings, technique sometimes used with air-core coils.

Quadruple Cone Coil with improved focality than Figure-8 coil in Transcranial Magnetic Stimulation

NASA Astrophysics Data System (ADS)

Rastogi, Priyam; Lee, Erik G.; Hadimani, Ravi L.; Jiles, David C.

Transcranial Magnetic Stimulation (TMS) is a non-invasive therapy which uses a time varying magnetic field to induce an electric field in the brain and to cause neuron depolarization. Magnetic coils play an important role in the TMS therapy since their coil geometry determines the focality and penetration's depth of the induced electric field in the brain. Quadruple Cone Coil (QCC) is a novel coil with an improved focality when compared to commercial Figure-8 coil. The results of this newly designed QCC coil are compared with the Figure-8 coil at two different positions of the head - vertex and dorsolateral prefrontal cortex, over the 50 anatomically realistic MRI derived head models. Parameters such as volume of stimulation, maximum electric, area of stimulation and location of maximum electric field are determined with the help of computer modelling of both coils. There is a decrease in volume of brain stimulated by 11.6 % and a modest improvement of 8 % in the location of maximum electric field due to QCC in comparison to the Figure-8 coil. The Carver Charitable Trust and The Galloway Foundation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solis, S. E.; Centro de Investigacion e Instrumentacion e Imagenologia Medica, Universidad Autonoma Metropolitana Iztapalapa, Mexico, DF 09340; Hernandez, J. A.

Arrays of antennas have been widely accepted for magnetic resonance imaging applications due to their high signal-to-noise ratio (SNR) over large volumes of interest. A new surface coil based on the magnetron tube and called slotted surface coil, has been recently introduced by our group. This coil design experimentally demonstrated a significant improvement over the circular-shaped coil when used in the receive-only mode. The slotted coils formed a two-sheet structure with a 90 deg. separation and each coil had 6 circular slots. Numerical simulations were performed using the finite element method for this coil design to study the behaviour ofmore » the array magnetic field. Then, we developed a two-coil array for brain magnetic resonance imaging to be operated at the resonant frequency of 170 MHz in the transceiver mode. Phantom images were acquired with our coil array and standard pulse sequences on a research-dedicated 4 Tesla scanner. Numerical simulations demonstrated that electromagnetic interaction between the coil elements is negligible, and that the magnetic field showed a good uniformity. In vitro images showed the feasibility of this coil array for standard pulses for high field magnetic resonance imaging.« less

Structure of bacteriophage T4 fibritin: a segmented coiled coil and the role of the C-terminal domain.

PubMed

Tao, Y; Strelkov, S V; Mesyanzhinov, V V; Rossmann, M G

1997-06-15

Oligomeric coiled-coil motifs are found in numerous protein structures; among them is fibritin, a structural protein of bacteriophage T4, which belongs to a class of chaperones that catalyze a specific phage-assembly process. Fibritin promotes the assembly of the long tail fibers and their subsequent attachment to the tail baseplate; it is also a sensing device that controls the retraction of the long tail fibers in adverse environments and, thus, prevents infection. The structure of fibritin had been predicted from sequence and biochemical analyses to be mainly a triple-helical coiled coil. The determination of its structure at atomic resolution was expected to give insights into the assembly process and biological function of fibritin, and the properties of modified coiled-coil structures in general. The three-dimensional structure of fibritin E, a deletion mutant of wild-type fibritin, was determined to 2.2 A resolution by X-ray crystallography. Three identical subunits of 119 amino acid residues form a trimeric parallel coiled-coil domain and a small globular C-terminal domain about a crystallographic threefold axis. The coiled-coil domain is divided into three segments that are separated by insertion loops. The C-terminal domain, which consists of 30 residues from each subunit, contains a beta-propeller-like structure with a hydrophobic interior. The residues within the C-terminal domain make extensive hydrophobic and some polar intersubunit interactions. This is consistent with the C-terminal domain being important for the correct assembly of fibritin, as shown earlier by mutational studies. Tight interactions between the C-terminal residues of adjacent subunits counteract the latent instability that is suggested by the structural properties of the coiled-coil segments. Trimerization is likely to begin with the formation of the C-terminal domain which subsequently initiates the assembly of the coiled coil. The interplay between the stabilizing effect of the C-terminal domain and the labile coiled-coil domain may be essential for the fibritin function and for the correct functioning of many other alpha-fibrous proteins.

Single phase four pole/six pole motor

DOEpatents

Kirschbaum, Herbert S.

1984-01-01

A single phase alternating current electric motor is provided with a main stator winding having two coil groups each including the series connection of three coils. These coil groups can be connected in series for six pole operation and in parallel for four pole operation. The coils are approximately equally spaced around the periphery of the machine but are not of equal numbers of turns. The two coil groups are identically wound and spaced 180 mechanical degrees apart. One coil of each group has more turns and a greater span than the other two coils.

Characterization and evaluation of a flexible MRI receive coil array for radiation therapy MR treatment planning using highly decoupled RF circuits.

PubMed

McGee, Kiaran P; Stormont, Robert S; Lindsay, Scott A; Taracila, Victor; Savitskij, Dennis; Robb, Fraser; Witte, Robert J; Kaufmann, Timothy J; Huston, John; Riederer, Stephen J; Borisch, Eric A; Rossman, Phillip J

2018-04-13

The growth in the use of magnetic resonance imaging (MRI) data for radiation therapy (RT) treatment planning has been facilitated by scanner hardware and software advances that have enabled RT patients to be imaged in treatment position while providing morphologic and functional assessment of tumor volumes and surrounding normal tissues. Despite these advances, manufacturers have been slow to develop radiofrequency (RF) coils that closely follow the contour of a RT patient undergoing MR imaging. Instead, relatively large form surface coil arrays have been adapted from diagnostic imaging. These arrays can be challenging to place on, and in general do not conform to the patient's body habitus, resulting in sub optimal image quality. The purpose of this study is to report on the characterization of a new flexible and highly decoupled RF coil for use in MR imaging of RT patients. Coil performance was evaluated by performing signal-to-noise ratio (SNR) and noise correlation measurements using two coil (SNR) and four coil (noise correlation) element combinations as a function of coil overlap distance and comparing these values to those obtained using conventional coil elements. In vivo testing was performed in both normal volunteers and patients using a four and 16 element RF coil. Phantom experiments demonstrate the highly decoupled nature of the new coil elements when compared to conventional RF coils, while in vivo testing demonstrate that these coils can be integrated into extremely flexible and form fitting substrates that follow the exact contour of the patient. The new coil design addresses limitations imposed by traditional surface coil arrays and have the potential to significantly impact MR imaging for both diagnostic and RT applications.

Characterization and evaluation of a flexible MRI receive coil array for radiation therapy MR treatment planning using highly decoupled RF circuits

NASA Astrophysics Data System (ADS)

McGee, Kiaran P.; Stormont, Robert S.; Lindsay, Scott A.; Taracila, Victor; Savitskij, Dennis; Robb, Fraser; Witte, Robert J.; Kaufmann, Timothy J.; Huston, John, III; Riederer, Stephen J.; Borisch, Eric A.; Rossman, Phillip J.

2018-04-01

The growth in the use of magnetic resonance imaging (MRI) data for radiation therapy (RT) treatment planning has been facilitated by scanner hardware and software advances that have enabled RT patients to be imaged in treatment position while providing morphologic and functional assessment of tumor volumes and surrounding normal tissues. Despite these advances, manufacturers have been slow to develop radiofrequency (RF) coils that closely follow the contour of a RT patient undergoing MR imaging. Instead, relatively large form surface coil arrays have been adapted from diagnostic imaging. These arrays can be challenging to place on, and in general do not conform to the patient’s body habitus, resulting in sub optimal image quality. The purpose of this study is to report on the characterization of a new flexible and highly decoupled RF coil for use in MR imaging of RT patients. Coil performance was evaluated by performing signal-to-noise ratio (SNR) and noise correlation measurements using two coil (SNR) and four coil (noise correlation) element combinations as a function of coil overlap distance and comparing these values to those obtained using conventional coil elements. In vivo testing was performed in both normal volunteers and patients using a four and 16 element RF coil. Phantom experiments demonstrate the highly decoupled nature of the new coil elements when compared to conventional RF coils, while in vivo testing demonstrate that these coils can be integrated into extremely flexible and form fitting substrates that follow the exact contour of the patient. The new coil design addresses limitations imposed by traditional surface coil arrays and have the potential to significantly impact MR imaging for both diagnostic and RT applications.

How much detail is needed in modeling a transcranial magnetic stimulation figure-8 coil: Measurements and brain simulations

PubMed Central

Mandija, Stefano; Sommer, Iris E. C.; van den Berg, Cornelis A. T.; Neggers, Sebastiaan F. W.

2017-01-01

Background Despite TMS wide adoption, its spatial and temporal patterns of neuronal effects are not well understood. Although progress has been made in predicting induced currents in the brain using realistic finite element models (FEM), there is little consensus on how a magnetic field of a typical TMS coil should be modeled. Empirical validation of such models is limited and subject to several limitations. Methods We evaluate and empirically validate models of a figure-of-eight TMS coil that are commonly used in published modeling studies, of increasing complexity: simple circular coil model; coil with in-plane spiral winding turns; and finally one with stacked spiral winding turns. We will assess the electric fields induced by all 3 coil models in the motor cortex using a computer FEM model. Biot-Savart models of discretized wires were used to approximate the 3 coil models of increasing complexity. We use a tailored MR based phase mapping technique to get a full 3D validation of the incident magnetic field induced in a cylindrical phantom by our TMS coil. FEM based simulations on a meshed 3D brain model consisting of five tissues types were performed, using two orthogonal coil orientations. Results Substantial differences in the induced currents are observed, both theoretically and empirically, between highly idealized coils and coils with correctly modeled spiral winding turns. Thickness of the coil winding turns affect minimally the induced electric field, and it does not influence the predicted activation. Conclusion TMS coil models used in FEM simulations should include in-plane coil geometry in order to make reliable predictions of the incident field. Modeling the in-plane coil geometry is important to correctly simulate the induced electric field and to correctly make reliable predictions of neuronal activation PMID:28640923

Integrated RF-shim coil allowing two degrees of freedom shim current.

PubMed

Jiazheng Zhou; Ying-Hua Chu; Yi-Cheng Hsu; Pu-Yeh Wu; Stockmann, Jason P; Fa-Hsuan Lin

2016-08-01

High-quality magnetic resonance imaging and spectroscopic measurements require a highly homogeneous magnetic field. Different from global shimming, localized off-resonance can be corrected by using multi-coil shimming. Previously, integrated RF and shimming coils have been used to implement multi-coil shimming. Such coils share the same conductor for RF signal reception and shim field generation. Here we propose a new design of the integrated RF-shim coil at 3-tesla, where two independent shim current paths are allowed in each coil. This coil permits a higher degree of freedom in shim current distribution design. We use both phantom experiments and simulations to demonstrate the feasibility of this new design.

DOE Office of Scientific and Technical Information (OSTI.GOV)

L.P. Ku and A.H. Boozer

Characteristics of modular coils for quasi-axisymmetric stellarators that are related to the plasma aspect ratio, number of field periods and rotational transform have been examined systematically. It is observed that, for a given plasma aspect ratio, the coil complexity tends to increase with the increased number of field periods. For a given number of field periods, the toroidal excursion of coil winding is reduced as the plasma aspect ratio is increased. It is also clear that the larger the coil-plasma separation is, the more complex the coils become. It is further demonstrated that it is possible to use other typesmore » of coils to complement modular coils to improve both the physics and the modular coil characteristics.« less

CRYOGENIC MAGNETS

DOEpatents

Post, R.F.; Taylor, C.E.

1963-05-21

A cryogenic magnet coil is described for generating magnetic fields of the order of 100,000 gauss with a minimum expenditure of energy lost in resistive heating of the coil inductors and energy lost irreversibly in running the coil refrigeration plant. The cryogenic coil comprises a coil conductor for generating a magnetic field upon energization with electrical current, and refrigeration means disposed in heat conductive relation to the coil conductor for cooling to a low temperature. A substantial reduction in the power requirements for generating these magnetic fields is attained by scaling the field generating coil to large size and particular dimensions for a particular conductor, and operating the coil at a particular optimum temperature commensurate with minimum overall power requirements. (AEC)

Feasibility study of a new RF coil design for prostate MRI

NASA Astrophysics Data System (ADS)

Ha, Seunghoon; Roeck, Werner W.; Cho, Jaedu; Nalcioglu, Orhan

2014-09-01

The combined use of a torso-pelvic RF array coil and endorectal RF coil is the current state-of-the-art in prostate MRI. The endorectal coil provides high detection sensitivity to acquire high-spatial resolution images and spectroscopic data, while the torso-pelvic coil provides large coverage to assess pelvic lymph nodes and pelvic bones for metastatic disease. However, the use of an endorectal coil is an invasive procedure that presents difficulties for both patients and technicians. In this study, we propose a novel non-invasive RF coil design that can provide both image signal to noise ratio and field of view coverage comparable to the combined torso-pelvic and endorectal coil configuration. A prototype coil was constructed and tested using a pelvic phantom. The results demonstrate that this new design is a viable alternative for prostate MRI

α/β coiled coils

PubMed Central

Hartmann, Marcus D; Mendler, Claudia T; Bassler, Jens; Karamichali, Ioanna; Ridderbusch, Oswin; Lupas, Andrei N; Hernandez Alvarez, Birte

2016-01-01

Coiled coils are the best-understood protein fold, as their backbone structure can uniquely be described by parametric equations. This level of understanding has allowed their manipulation in unprecedented detail. They do not seem a likely source of surprises, yet we describe here the unexpected formation of a new type of fiber by the simple insertion of two or six residues into the underlying heptad repeat of a parallel, trimeric coiled coil. These insertions strain the supercoil to the breaking point, causing the local formation of short β-strands, which move the path of the chain by 120° around the trimer axis. The result is an α/β coiled coil, which retains only one backbone hydrogen bond per repeat unit from the parent coiled coil. Our results show that a substantially novel backbone structure is possible within the allowed regions of the Ramachandran space with only minor mutations to a known fold. DOI: http://dx.doi.org/10.7554/eLife.11861.001 PMID:26771248

Parametric Study of HTS Coil Quench Protection Strategies

NASA Astrophysics Data System (ADS)

Seibert, Joseph; Zarnstorff, Michael; Zhai, Yuhu

2016-10-01

Next generation fusion devices require high magnetic fields to adequately contain burning plasmas. Use of high temperature superconducting (HTS) coils to generate these magnetic fields would lower energy cost of operation as well as increase stability of the superconducting state compared to low temperature superconducting coils. However, use of HTS coils requires developing quench protection strategies to prevent damage to the coils. One technique involves the utilization of copper discs and other conductors mutually coupled to the HTS coil to quickly extract the current from the coil. Another technique allows conduction between HTS turns to reduce the current in the coil during quench. This project describes a parametric study of the HTS coil and resistive-conductor setup in order to determine limiting cases of the geometry in an attempt to optimize current extraction and coil protection during quench scenarios. This work was supported in part by the U.S. Department of Energy, Office of Science, Office of Workforce Development for Teachers and Scientists (WDTS) under the Science Undergraduate Laboratory Internship (SULI) program.

Superconducting magnetic energy storage apparatus structural support system

DOEpatents

Withers, Gregory J.; Meier, Stephen W.; Walter, Robert J.; Child, Michael D.; DeGraaf, Douglas W.

1992-01-01

A superconducting magnetic energy storage apparatus comprising a cylindrical superconducting coil; a cylindrical coil containment vessel enclosing the coil and adapted to hold a liquid, such as liquefied helium; and a cylindrical vacuum vessel enclosing the coil containment vessel and located in a restraining structure having inner and outer circumferential walls and a floor; the apparatus being provided with horizontal compression members between (1) the coil and the coil containment vessel and (2) between the coil containment vessel and the vacuum vessel, compression bearing members between the vacuum vessel and the restraining structure inner and outer walls, vertical support members (1) between the coil bottom and the coil containment vessel bottom and (2) between the coil containment vessel bottom and the vacuum vessel bottom, and external supports between the vacuum vessel bottom and the restraining structure floor, whereby the loads developed by thermal and magnetic energy changes in the apparatus can be accommodated and the structural integrity of the apparatus be maintained.

Folding behavior of four silks of giant honey bee reflects the evolutionary conservation of aculeate silk proteins.

PubMed

Maitip, Jakkrawut; Trueman, Holly E; Kaehler, Benjamin D; Huttley, Gavin A; Chantawannakul, Panuwan; Sutherland, Tara D

2015-04-01

Multiple gene duplication events in the precursor of the Aculeata (bees, ants, hornets) gave rise to four silk genes. Whilst these homologs encode proteins with similar amino acid composition and coiled coil structure, the retention of all four homologs implies they each are important. In this study we identified, produced and characterized the four silk proteins from Apis dorsata, the giant Asian honeybee. The proteins were readily purified, allowing us to investigate the folding behavior of solutions of individual proteins in comparison to mixtures of all four proteins at concentrations where they assemble into their native coiled coil structure. In contrast to solutions of any one protein type, solutions of a mixture of the four proteins formed coiled coils that were stable against dilution and detergent denaturation. The results are consistent with the formation of a heteromeric coiled coil protein complex. The mechanism of silk protein coiled coil formation and evolution is discussed in light of these results. Copyright © 2015 Elsevier Ltd. All rights reserved.

Minimizing hot spot temperature in asymmetric gradient coil design.

PubMed

While, Peter T; Forbes, Larry K; Crozier, Stuart

2011-08-01

Heating caused by gradient coils is a considerable concern in the operation of magnetic resonance imaging (MRI) scanners. Hot spots can occur in regions where the gradient coil windings are closely spaced. These problem areas are particularly common in the design of gradient coils with asymmetrically located target regions. In this paper, an extension of an existing coil design method is described, to enable the design of asymmetric gradient coils with reduced hot spot temperatures. An improved model is presented for predicting steady-state spatial temperature distributions for gradient coils. A great amount of flexibility is afforded by this model to consider a wide range of geometries and system material properties. A feature of the temperature distribution related to the temperature gradient is used in a relaxed fixed point iteration routine for successively altering coil windings to have a lower hot spot temperature. Results show that significant reductions in peak temperature are possible at little or no cost to coil performance when compared to minimum power coils of equivalent field error.

Minimum maximum temperature gradient coil design.

PubMed

While, Peter T; Poole, Michael S; Forbes, Larry K; Crozier, Stuart

2013-08-01

Ohmic heating is a serious problem in gradient coil operation. A method is presented for redesigning cylindrical gradient coils to operate at minimum peak temperature, while maintaining field homogeneity and coil performance. To generate these minimaxT coil windings, an existing analytic method for simulating the spatial temperature distribution of single layer gradient coils is combined with a minimax optimization routine based on sequential quadratic programming. Simulations are provided for symmetric and asymmetric gradient coils that show considerable improvements in reducing maximum temperature over existing methods. The winding patterns of the minimaxT coils were found to be heavily dependent on the assumed thermal material properties and generally display an interesting "fish-eye" spreading of windings in the dense regions of the coil. Small prototype coils were constructed and tested for experimental validation and these demonstrate that with a reasonable estimate of material properties, thermal performance can be improved considerably with negligible change to the field error or standard figures of merit. © 2012 Wiley Periodicals, Inc.

Analysis and experimental study of wireless power transfer with HTS coil and copper coil as the intermediate resonators system

NASA Astrophysics Data System (ADS)

Wang, Xiufang; Nie, Xinyi; Liang, Yilang; Lu, Falong; Yan, Zhongming; Wang, Yu

2017-01-01

Intermediate resonator (repeater) between transmitter and receiver can significantly increase the distance of wireless power transfer (WPT) and the efficiency of wireless power transfer. The wireless power transfer via strongly coupled magnetic resonances with an high temperature superconducting (HTS) coil and copper coil as intermediate resonators was presented in this paper. The electromagnetic experiment system under different conditions with different repeating coils were simulated by finite element software. The spatial distribution patterns of magnetic induction intensity at different distances were plotted. In this paper, we examined transfer characteristics with HTS repeating coil and copper repeating coil at 77 K and 300 K, respectively. Simulation and experimental results show that HTS and copper repeating coil can effectively enhance the space magnetic induction intensity, which has significant effect on improving the transmission efficiency and lengthening transmission distance. We found that the efficiency and the distance of wireless power transfer system with an HTS coil as repeater is much higher by using of copper coil as repeater.

Study on elimination of screening-current-induced field in pancake-type non-insulated HTS coil

NASA Astrophysics Data System (ADS)

Kim, K. L.; Song, J. B.; Yang, D. G.; Kim, Y. G.; Kim, T. H.; Kim, S. K.; Park, M. W.; Lee, H. G.

2016-03-01

This paper presents the details of a recent study on the removal of the screening-current-induced field (SCIF) in a pancake-type non-insulated high-temperature superconductor coil (NI coil). To determine the SCIF in the NI coil, the magnetic flux density (B z ) was calculated using the equivalent circuit model of the coil and compared to the B z obtained empirically. The experimental results indicate that the SCIF elimination in the NI coil was enhanced upon increasing the amplitude and frequency of the AC current being supplied to the background coil. Moreover, the SCIF in the NI coil was successfully removed by applying the appropriate external AC magnetic field intensity. This is because the magnetization direction of the SCIF changed completely from radial to spiral, a phenomenon termed the ‘vortex shaking effect.’ Overall, this study confirmed that the SCIF in a pancake-type NI coil can be effectively removed by exposing the coil to an external AC magnetic field.

Eccentric figure-eight coils for transcranial magnetic stimulation.

PubMed

Sekino, Masaki; Ohsaki, Hiroyuki; Takiyama, Yoshihiro; Yamamoto, Keita; Matsuzaki, Taiga; Yasumuro, Yoshihiro; Nishikawa, Atsushi; Maruo, Tomoyuki; Hosomi, Koichi; Saitoh, Youichi

2015-01-01

Previously we proposed an eccentric figure-eight coil that can cause threshold stimulation in the brain at lower driving currents. In this study, we performed numerical simulations and magnetic stimulations to healthy subjects for evaluating the advantages of the eccentric coil. The simulations were performed using a simplified spherical brain model and a realistic human brain model. We found that the eccentric coil required a driving current intensity of approximately 18% less than that required by the concentric coil to cause comparable eddy current densities within the brain. The eddy current localization of the eccentric coil was slightly higher than that of the concentric coil. A prototype eccentric coil was designed and fabricated. Instead of winding a wire around a bobbin, we cut eccentric-spiral slits on the insulator cases, and a wire was woven through the slits. The coils were used to deliver magnetic stimulation to healthy subjects; among our results, we found that the current slew rate corresponding to motor threshold values for the concentric and eccentric coils were 86 and 78 A/µs, respectively. The results indicate that the eccentric coil consistently requires a lower driving current to reach the motor threshold than the concentric coil. Future development of compact magnetic stimulators will enable the treatment of some intractable neurological diseases at home. © 2014 Wiley Periodicals, Inc.

The mutual inductance calculation between circular and quadrilateral coils at arbitrary attitudes using a rotation matrix for airborne transient electromagnetic systems

NASA Astrophysics Data System (ADS)

Ji, Yanju; Wang, Hongyuan; Lin, Jun; Guan, Shanshan; Feng, Xue; Li, Suyi

2014-12-01

Performance testing and calibration of airborne transient electromagnetic (ATEM) systems are conducted to obtain the electromagnetic response of ground loops. It is necessary to accurately calculate the mutual inductance between transmitting coils, receiving coils and ground loops to compute the electromagnetic responses. Therefore, based on Neumann's formula and the measured attitudes of the coils, this study deduces the formula for the mutual inductance calculation between circular and quadrilateral coils, circular and circular coils, and quadrilateral and quadrilateral coils using a rotation matrix, and then proposes a method to calculate the mutual inductance between two coils at arbitrary attitudes (roll, pitch, and yaw). Using coil attitude simulated data of an ATEM system, we calculate the mutual inductance of transmitting coils and ground loops at different attitudes, analyze the impact of coil attitudes on mutual inductance, and compare the computational accuracy and speed of the proposed method with those of other methods using the same data. The results show that the relative error of the calculation is smaller and that the speed-up is significant compared to other methods. Moreover, the proposed method is also applicable to the mutual inductance calculation of polygonal and circular coils at arbitrary attitudes and is highly expandable.

Manufacturing of a REBCO racetrack coil using thermoplastic resin aiming at Maglev application

NASA Astrophysics Data System (ADS)

Mizuno, Katsutoshi; Ogata, Masafumi; Hasegawa, Hitoshi

2015-11-01

The REBCO coated conductor is a promising technology for the Maglev application in terms of its high critical temperature. The operating temperature of the on-board magnets can be around 40-50 K with the coated conductor. The REBCO coils are cooled by cryocoolers directly, and hence the thermal design of the REBCO coils significantly changes from that of LTS coils. We have developed a novel REBCO coil structure using thermoplastic resin. The coil is not impregnated and the thermoplastic resin is used to bond the coil winding and the heat transfer members, e.g. copper and aluminum plates. The viscosity of the thermoplastic resin is high enough for the thermoplastic resin not to permeate between the turns in the coil. Therefore, the thermal stress does not occur and the risk of degradation is removed. This paper contains the following three topics. First, the thermal resistance of the thermoplastic resin was measured at cryogenic temperature. Then, a small round REBCO coil was experimentally produced. It has been confirmed that the thermoplastic resin does not cause the degradation and, the adhesion between the coil winding and copper plates withstands the thermal stress. Finally, we successfully produced a full-scale racetrack REBCO coil applying the coil structure with the thermoplastic resin.

Power Loss Analysis and Comparison of Segmented and Unsegmented Energy Coupling Coils for Wireless Energy Transfer

PubMed Central

Tang, Sai Chun; McDannold, Nathan J.

2015-01-01

This paper investigated the power losses of unsegmented and segmented energy coupling coils for wireless energy transfer. Four 30-cm energy coupling coils with different winding separations, conductor cross-sectional areas, and number of turns were developed. The four coils were tested in both unsegmented and segmented configurations. The winding conduction and intrawinding dielectric losses of the coils were evaluated individually based on a well-established lumped circuit model. We found that the intrawinding dielectric loss can be as much as seven times higher than the winding conduction loss at 6.78 MHz when the unsegmented coil is tightly wound. The dielectric loss of an unsegmented coil can be reduced by increasing the winding separation or reducing the number of turns, but the power transfer capability is reduced because of the reduced magnetomotive force. Coil segmentation using resonant capacitors has recently been proposed to significantly reduce the operating voltage of a coil to a safe level in wireless energy transfer for medical implants. Here, we found that it can naturally eliminate the dielectric loss. The coil segmentation method and the power loss analysis used in this paper could be applied to the transmitting, receiving, and resonant coils in two- and four-coil energy transfer systems. PMID:26640745

Power Loss Analysis and Comparison of Segmented and Unsegmented Energy Coupling Coils for Wireless Energy Transfer.

PubMed

Tang, Sai Chun; McDannold, Nathan J

2015-03-01

This paper investigated the power losses of unsegmented and segmented energy coupling coils for wireless energy transfer. Four 30-cm energy coupling coils with different winding separations, conductor cross-sectional areas, and number of turns were developed. The four coils were tested in both unsegmented and segmented configurations. The winding conduction and intrawinding dielectric losses of the coils were evaluated individually based on a well-established lumped circuit model. We found that the intrawinding dielectric loss can be as much as seven times higher than the winding conduction loss at 6.78 MHz when the unsegmented coil is tightly wound. The dielectric loss of an unsegmented coil can be reduced by increasing the winding separation or reducing the number of turns, but the power transfer capability is reduced because of the reduced magnetomotive force. Coil segmentation using resonant capacitors has recently been proposed to significantly reduce the operating voltage of a coil to a safe level in wireless energy transfer for medical implants. Here, we found that it can naturally eliminate the dielectric loss. The coil segmentation method and the power loss analysis used in this paper could be applied to the transmitting, receiving, and resonant coils in two- and four-coil energy transfer systems.

Computational assessment of folding energy landscapes in heterodimeric coiled coils.

PubMed

André, Ingemar; Bjelic, Sinisa

2018-07-01

The coiled coil structural motif consists of alpha helices supercoiling around each other to form staggered knobs-into-holes packing. Such structures are deceptively simple, especially as they often can be described with parametric equations, but are known to exist in various conformations. Even the simplest systems, consisting of 2 monomers, can assemble into a wide range of states. They can form canonical as well as noncanonical coiled coils, be parallel or antiparallel, where helices associate with different degrees of shift, tilt, and rotation. Here, we investigate the energy landscape of heterodimeric coiled coils by carrying out de novo folding simulations starting from amino acid sequence. We folded a diverse set of 22 heterodimers and demonstrate that the approach is capable of identifying the atomic details in the experimental structure in the majority of cases. Our methodology also enables exploration of alternative states that can be accessible in solution beyond the experimentally determined structure. For many systems, we observe folding energy landscapes with multiple energy minima and several isoenergetic states. By comparing coiled coils from single domains and those extracted from larger proteins, we find that standalone coiled coils have deeper energy wells at the experimentally determined conformation. By folding the competing homodimeric states in addition to the heterodimers, we observe that the structural specificity towards the heteromeric state is often small. Taken together, our results demonstrate that de novo folding simulations can be a powerful tool to characterize structural specificity of coiled coils when coupled to assessment of energy landscapes. © 2018 Wiley Periodicals, Inc.

Coil optimisation for transcranial magnetic stimulation in realistic head geometry.

PubMed

Koponen, Lari M; Nieminen, Jaakko O; Mutanen, Tuomas P; Stenroos, Matti; Ilmoniemi, Risto J

Transcranial magnetic stimulation (TMS) allows focal, non-invasive stimulation of the cortex. A TMS pulse is inherently weakly coupled to the cortex; thus, magnetic stimulation requires both high current and high voltage to reach sufficient intensity. These requirements limit, for example, the maximum repetition rate and the maximum number of consecutive pulses with the same coil due to the rise of its temperature. To develop methods to optimise, design, and manufacture energy-efficient TMS coils in realistic head geometry with an arbitrary overall coil shape. We derive a semi-analytical integration scheme for computing the magnetic field energy of an arbitrary surface current distribution, compute the electric field induced by this distribution with a boundary element method, and optimise a TMS coil for focal stimulation. Additionally, we introduce a method for manufacturing such a coil by using Litz wire and a coil former machined from polyvinyl chloride. We designed, manufactured, and validated an optimised TMS coil and applied it to brain stimulation. Our simulations indicate that this coil requires less than half the power of a commercial figure-of-eight coil, with a 41% reduction due to the optimised winding geometry and a partial contribution due to our thinner coil former and reduced conductor height. With the optimised coil, the resting motor threshold of abductor pollicis brevis was reached with the capacitor voltage below 600 V and peak current below 3000 A. The described method allows designing practical TMS coils that have considerably higher efficiency than conventional figure-of-eight coils. Copyright © 2017 Elsevier Inc. All rights reserved.

Local Multi-Channel RF Surface Coil versus Body RF Coil Transmission for Cardiac Magnetic Resonance at 3 Tesla: Which Configuration Is Winning the Game?

PubMed

Weinberger, Oliver; Winter, Lukas; Dieringer, Matthias A; Els, Antje; Oezerdem, Celal; Rieger, Jan; Kuehne, Andre; Cassara, Antonino M; Pfeiffer, Harald; Wetterling, Friedrich; Niendorf, Thoralf

2016-01-01

The purpose of this study was to demonstrate the feasibility and efficiency of cardiac MR at 3 Tesla using local four-channel RF coil transmission and benchmark it against large volume body RF coil excitation. Electromagnetic field simulations are conducted to detail RF power deposition, transmission field uniformity and efficiency for local and body RF coil transmission. For both excitation regimes transmission field maps are acquired in a human torso phantom. For each transmission regime flip angle distributions and blood-myocardium contrast are examined in a volunteer study of 12 subjects. The feasibility of the local transceiver RF coil array for cardiac chamber quantification at 3 Tesla is demonstrated. Our simulations and experiments demonstrate that cardiac MR at 3 Tesla using four-channel surface RF coil transmission is competitive versus current clinical CMR practice of large volume body RF coil transmission. The efficiency advantage of the 4TX/4RX setup facilitates shorter repetition times governed by local SAR limits versus body RF coil transmission at whole-body SAR limit. No statistically significant difference was found for cardiac chamber quantification derived with body RF coil versus four-channel surface RF coil transmission. Our simulation also show that the body RF coil exceeds local SAR limits by a factor of ~2 when driven at maximum applicable input power to reach the whole-body SAR limit. Pursuing local surface RF coil arrays for transmission in cardiac MR is a conceptually appealing alternative to body RF coil transmission, especially for patients with implants.

Structural basis for cargo binding and autoinhibition of Bicaudal-D1 by a parallel coiled-coil with homotypic registry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Terawaki, Shin-ichi, E-mail: terawaki@gunma-u.ac.jp; SPring-8 Center, RIKEN, 1-1-1 Koto, Sayo-cho, Sayo-gun, Hyogo 679-5148; Yoshikane, Asuka

Bicaudal-D1 (BICD1) is an α-helical coiled-coil protein mediating the attachment of specific cargo to cytoplasmic dynein. It plays an essential role in minus end-directed intracellular transport along microtubules. The third C-terminal coiled-coil region of BICD1 (BICD1 CC3) has an important role in cargo sorting, including intracellular vesicles associating with the small GTPase Rab6 and the nuclear pore complex Ran binding protein 2 (RanBP2), and inhibiting the association with cytoplasmic dynein by binding to the first N-terminal coiled-coil region (CC1). The crystal structure of BICD1 CC3 revealed a parallel homodimeric coiled-coil with asymmetry and complementary knobs-into-holes interactions, differing from Drosophila BicDmore » CC3. Furthermore, our binding study indicated that BICD1 CC3 possesses a binding surface for two distinct cargos, Rab6 and RanBP2, and that the CC1-binding site overlaps with the Rab6-binding site. These findings suggest a molecular basis for cargo recognition and autoinhibition of BICD proteins during dynein-dependent intracellular retrograde transport. - Highlights: • BICD1 CC3 is a parallel homodimeric coiled-coil with axial asymmetry. • The coiled-coil packing of BICD1 CC3 is adapted to the equivalent heptad position. • BICD1 CC3 has distinct binding sites for two classes of cargo, Rab6 and RanBP2. • The CC1-binding site of BICD1 CC3 overlaps with the Rab6-binding site.« less

Analytical Model and Optimized Design of Power Transmitting Coil for Inductively Coupled Endoscope Robot.

PubMed

Ke, Quan; Luo, Weijie; Yan, Guozheng; Yang, Kai

2016-04-01

A wireless power transfer system based on the weakly inductive coupling makes it possible to provide the endoscope microrobot (EMR) with infinite power. To facilitate the patients' inspection with the EMR system, the diameter of the transmitting coil is enlarged to 69 cm. Due to the large transmitting range, a high quality factor of the Litz-wire transmitting coil is a necessity to ensure the intensity of magnetic field generated efficiently. Thus, this paper builds an analytical model of the transmitting coil, and then, optimizes the parameters of the coil by enlarging the quality factor. The lumped model of the transmitting coil includes three parameters: ac resistance, self-inductance, and stray capacitance. Based on the exact two-dimension solution, the accurate analytical expression of ac resistance is derived. Several transmitting coils of different specifications are utilized to verify this analytical expression, being in good agreements with the measured results except the coils with a large number of strands. Then, the quality factor of transmitting coils can be well predicted with the available analytical expressions of self- inductance and stray capacitance. Owing to the exact estimation of quality factor, the appropriate coil turns of the transmitting coil is set to 18-40 within the restrictions of transmitting circuit and human tissue issues. To supply enough energy for the next generation of the EMR equipped with a Ø9.5×10.1 mm receiving coil, the coil turns of the transmitting coil is optimally set to 28, which can transfer a maximum power of 750 mW with the remarkable delivering efficiency of 3.55%.

Method of eliminating the training effect in superconducting coils by post-wind preload

DOEpatents

Heim, Joseph R.

1976-01-01

The training effect in superconducting coils is eliminated by winding the coil with a composite material that includes both a superconductor and a normal material and then applying stresses to the wound coil in the direction that electromagnetic stresses will be applied to the coil during normal use and in a magnitude greater than the calculated magnitude of the greatest electromagnetic stresses to be applied to the coil.

Potential damage to dc superconducting magnets due to high frequency electromagnetic waves

NASA Technical Reports Server (NTRS)

Gabriel, G. J.; Burkhart, J. A.

1977-01-01

Studies of a d.c. superconducting magnet coil indicate that the large coil behaves as a straight waveguide structure. Voltages between layers within the coil sometimes exceeded those recorded at terminals where protective resistors are located. Protection of magnet coils against these excessive voltages could be accomplished by impedance matching throughout the coil system. The wave phenomenon associated with superconducting magnetic coils may create an instability capable of converting the energy of a quiescent d.c. superconducting coil into dissipative a.c. energy, even in cases when dielectric breakdown does not take place.

Single phase four pole/six pole motor

DOEpatents

Kirschbaum, H.S.

1984-10-09

A single phase alternating current electric motor is provided with a main stator winding having two coil groups each including the series connection of three coils. These coil groups can be connected in series for six pole operation and in parallel for four pole operation. The coils are approximately equally spaced around the periphery of the machine but are not of equal numbers of turns. The two coil groups are identically wound and spaced 180 mechanical degrees apart. One coil of each group has more turns and a greater span than the other two coils. 10 figs.

Investigating the effect of coil model losses on computational electromagnetic exposure of an ASTM phantom at 64 MHz MRI.

PubMed

Kozlov, Mikhail; Horner, Marc; Kainz, Wolfgang; Angelone, Leonardo M

2017-07-01

The goal of this work is to investigate the effect of coil losses on the electromagnetic field generated in an ASTM phantom by a birdcage coil. The study was based on different numerical implementations of an RF body coil at 64 MHz, using the same 3D EM and RF circuit co-simulation procedure. The coil quality factor was evaluated with respect to losses due to power feed mismatch and to resistive losses of the coil components. The results of the study showed that the magnetic field at the coil iso-center, normalized to the square root of the whole body specific absorption rate, depends on the coil quality factor.

Transcranial Magnetic Stimulation-coil design with improved focality

NASA Astrophysics Data System (ADS)

Rastogi, P.; Lee, E. G.; Hadimani, R. L.; Jiles, D. C.

2017-05-01

Transcranial Magnetic Stimulation (TMS) is a technique for neuromodulation that can be used as a non-invasive therapy for various neurological disorders. In TMS, a time varying magnetic field generated from an electromagnetic coil placed on the scalp is used to induce an electric field inside the brain. TMS coil geometry plays an important role in determining the focality and depth of penetration of the induced electric field responsible for stimulation. Clinicians and basic scientists are interested in stimulating a localized area of the brain, while minimizing the stimulation of surrounding neural networks. In this paper, a novel coil has been proposed, namely Quadruple Butterfly Coil (QBC) with an improved focality over the commercial Figure-8 coil. Finite element simulations were conducted with both the QBC and the conventional Figure-8 coil. The two coil's stimulation profiles were assessed with 50 anatomically realistic MRI derived head models. The coils were positioned on the vertex and the scalp over the dorsolateral prefrontal cortex to stimulate the brain. Computer modeling of the coils has been done to determine the parameters of interest-volume of stimulation, maximum electric field, location of maximum electric field and area of stimulation across all 50 head models for both coils.

Three Element Phased Array Coil for Imaging of Rat Spinal Cord at 7T

PubMed Central

Mogatadakala, Kishore V.; Bankson, James A.; Narayana, Ponnada A.

2008-01-01

In order to overcome some of the limitations of an implantable coil, including its invasive nature and limited spatial coverage, a three element phased array coil is described for high resolution magnetic resonance imaging (MRI) of rat spinal cord. This coil allows imaging both thoracic and cervical segments of rat spinal cord. In the current design, coupling between the nearest neighbors was minimized by overlapping the coil elements. A simple capacitive network was used for decoupling the next neighbor elements. The dimensions of individual coils in the array were determined based on the signal-to-noise ratio (SNR) measurements performed on a phantom with three different surface coils. SNR measurements on a phantom demonstrated higher SNR of the phased array coil relative to two different volume coils. In-vivo images acquired on rat spinal cord with our coil demonstrated excellent gray and white matter contrast. To evaluate the performance of the phased array coil under parallel imaging, g-factor maps were obtained for two different acceleration factors of 2 and 3. These simulations indicate that parallel imaging with acceleration factor of 2 would be possible without significant image reconstruction related noise amplifications. PMID:19025892

Retrofitting coils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merrill, D.G.

1995-12-01

This article provides guidelines for maintaining efficiency by determining which coils require replacement and the selection of replacement coils to match the originals in terms of size, performance, materials, and material thickness. Coils in the Rio Hondo College have been in use 24 years. The author recently found an installation where the coils installed 20 years ago look like new, which is the result of a highly effective preventive maintenance program. But these exceptions are countered by some installations lasting considerably less time. Periodic coil inspections are the best way to find leaks and deterioration. Leaking coils have an unhappymore » way of announcing their presence through unwanted water on ceilings, walls, and machine room floors. Minuscule streams of water impinge on nonwater-tight housings or are picked up in the air stream to leak out of the ductwork. Coil return bends and headers seem to have the greater incidence of failure and should be checked first for pinhole or joint leaks. Also, check along the points where the tubes penetrate the tube sheets. The coil headers should be checked as should the tubes along the front and backside of the coil. The more rows the coil has, the more difficult this latter assignment becomes.« less

INTERCOMPARISON OF PERFORMANCE OF RF COIL GEOMETRIES FOR HIGH FIELD MOUSE CARDIAC MRI

PubMed Central

Constantinides, Christakis; Angeli, S.; Gkagkarellis, S.; Cofer, G.

2012-01-01

Multi-turn spiral surface coils are constructed in flat and cylindrical arrangements and used for high field (7.1 T) mouse cardiac MRI. Their electrical and imaging performances, based on experimental measurements, simulations, and MRI experiments in free space, and under phantom, and animal loading conditions, are compared with a commercially available birdcage coil. Results show that the four-turn cylindrical spiral coil exhibits improved relative SNR (rSNR) performance to the flat coil counterpart, and compares fairly well with a commercially available birdcage coil. Phantom experiments indicate a 50% improvement in the SNR for penetration depths ≤ 6.1 mm from the coil surface compared to the birdcage coil, and an increased penetration depth at the half-maximum field response of 8 mm in the 4-spiral cylindrical coil case, in contrast to 2.9 mm in the flat 4-turn spiral case. Quantitative comparison of the performance of the two spiral coil geometries in anterior, lateral, inferior, and septal regions of the murine heart yield maximum mean percentage rSNR increases of the order of 27–167% in vivo post-mortem (cylindrical compared to flat coil). The commercially available birdcage outperforms the cylindrical spiral coil in rSNR by a factor of 3–5 times. The comprehensive approach and methodology adopted to accurately design, simulate, implement, and test radiofrequency coils of any geometry and type, under any loading conditions, can be generalized for any application of high field mouse cardiac MRI. PMID:23204945

Optimization of Coil Element Configurations for a Matrix Gradient Coil.

PubMed

Kroboth, Stefan; Layton, Kelvin J; Jia, Feng; Littin, Sebastian; Yu, Huijun; Hennig, Jurgen; Zaitsev, Maxim

2018-01-01

Recently, matrix gradient coils (also termed multi-coils or multi-coil arrays) were introduced for imaging and B 0 shimming with 24, 48, and even 84 coil elements. However, in imaging applications, providing one amplifier per coil element is not always feasible due to high cost and technical complexity. In this simulation study, we show that an 84-channel matrix gradient coil (head insert for brain imaging) is able to create a wide variety of field shapes even if the number of amplifiers is reduced. An optimization algorithm was implemented that obtains groups of coil elements, such that a desired target field can be created by driving each group with an amplifier. This limits the number of amplifiers to the number of coil element groups. Simulated annealing is used due to the NP-hard combinatorial nature of the given problem. A spherical harmonic basis set up to the full third order within a sphere of 20-cm diameter in the center of the coil was investigated as target fields. We show that the median normalized least squares error for all target fields is below approximately 5% for 12 or more amplifiers. At the same time, the dissipated power stays within reasonable limits. With a relatively small set of amplifiers, switches can be used to sequentially generate spherical harmonics up to third order. The costs associated with a matrix gradient coil can be lowered, which increases the practical utility of matrix gradient coils.

Comparison of the induced fields using different coil configurations during deep transcranial magnetic stimulation.

PubMed

Lu, Mai; Ueno, Shoogo

2017-01-01

Stimulation of deeper brain structures by transcranial magnetic stimulation (TMS) plays a role in the study of reward and motivation mechanisms, which may be beneficial in the treatment of several neurological and psychiatric disorders. However, electric field distributions induced in the brain by deep transcranial magnetic stimulation (dTMS) are still unknown. In this paper, the double cone coil, H-coil and Halo-circular assembly (HCA) coil which have been proposed for dTMS have been numerically designed. The distributions of magnetic flux density, induced electric field in an anatomically based realistic head model by applying the dTMS coils were numerically calculated by the impedance method. Results were compared with that of standard figure-of-eight (Fo8) coil. Simulation results show that double cone, H- and HCA coils have significantly deep field penetration compared to the conventional Fo8 coil, at the expense of induced higher and wider spread electrical fields in superficial cortical regions. Double cone and HCA coils have better ability to stimulate deep brain subregions compared to that of the H-coil. In the mean time, both double cone and HCA coils increase risk for optical nerve excitation. Our results suggest although the dTMS coils offer new tool with potential for both research and clinical applications for psychiatric and neurological disorders associated with dysfunctions of deep brain regions, the selection of the most suitable coil settings for a specific clinical application should be based on a balanced evaluation between stimulation depth and focality.

Intra-coil interactions in split gradient coils in a hybrid MRI-LINAC system

NASA Astrophysics Data System (ADS)

Tang, Fangfang; Freschi, Fabio; Sanchez Lopez, Hector; Repetto, Maurizio; Liu, Feng; Crozier, Stuart

2016-04-01

An MRI-LINAC system combines a magnetic resonance imaging (MRI) system with a medical linear accelerator (LINAC) to provide image-guided radiotherapy for targeting tumors in real-time. In an MRI-LINAC system, a set of split gradient coils is employed to produce orthogonal gradient fields for spatial signal encoding. Owing to this unconventional gradient configuration, eddy currents induced by switching gradient coils on and off may be of particular concern. It is expected that strong intra-coil interactions in the set will be present due to the constrained return paths, leading to potential degradation of the gradient field linearity and image distortion. In this study, a series of gradient coils with different track widths have been designed and analyzed to investigate the electromagnetic interactions between coils in a split gradient set. A driving current, with frequencies from 100 Hz to 10 kHz, was applied to study the inductive coupling effects with respect to conductor geometry and operating frequency. It was found that the eddy currents induced in the un-energized coils (hereby-referred to as passive coils) positively correlated with track width and frequency. The magnetic field induced by the eddy currents in the passive coils with wide tracks was several times larger than that induced by eddy currents in the cold shield of cryostat. The power loss in the passive coils increased with the track width. Therefore, intra-coil interactions should be included in the coil design and analysis process.

In vitro study of near-wall flow in a cerebral aneurysm model with and without coils.

PubMed

Goubergrits, L; Thamsen, B; Berthe, A; Poethke, J; Kertzscher, U; Affeld, K; Petz, C; Hege, H-C; Hoch, H; Spuler, A

2010-09-01

Coil embolization procedures change the flow conditions in the cerebral aneurysm and, therefore, in the near-wall region. Knowledge of these flow changes may be helpful to optimize therapy. The goal of this study was to investigate the effect of the coil-packing attenuation on the near-wall flow and its variability due to differences in the coil structure. An enlarged transparent model of an ACA aneurysm was fabricated on the basis of CT angiography. The near-wall flow was visualized by using a recently proposed technique called Wall-PIV. Coil-packing attenuation of 10%, 15%, and 20% were investigated and compared with an aneurysmal flow without coils. Then the flow variability due to the coil introduction was analyzed in 10 experiments by using a packing attenuation of 15%. A small packing attenuation of 10% already alters the near-wall flow significantly in a large part of the aneurysmal sac. These flow changes are characterized by a slow flow with short (interrupted) path lines. An increased packing attenuation expands the wall area exposed to the altered flow conditions. This area, however, depends on the coil position and/or on the 3D coil structure in the aneurysm. To our knowledge, this is the first time the near-wall flow changes caused by coils in an aneurysm model have been visualized. It can be concluded that future hydrodynamic studies of coil therapy should include an investigation of the coil structure in addition to the coil-packing attenuation.

Intravascular Placement of Metallic Coils as Lung Tumor Markers for CyberKnife Stereotactic Radiation Therapy.

PubMed

Karaman, Kutlay; Dokdok, A Murat; Karadeniz, Oktay; Ceylan, Cemile; Engin, Kayıhan

2015-01-01

To present our experience with placing endovascular coils in pulmonary arteries used as a fiducial marker for CyberKnife therapy and to describe the technical details and complications of the procedure. Between June 2005 and September 2013, 163 patients with primary or secondary lung malignancies, referred for fiducial placement for stereotactic radiosurgery, were retrospectively reviewed. Fourteen patients (9 men, 5 women; mean age, 70 years) with a history of pneumonectomy (n = 3), lobectomy (n = 3) or with severe cardiopulmonary co-morbidity (n = 8) underwent coil (fiducial marker) placement. Pushable or detachable platinum micro coils (n = 49) 2-3 mm in size were inserted through coaxial microcatheters into a small distal pulmonary artery in the vicinity of the tumor under biplane angiography/fluoroscopy guidance. Forty nine coils with a median number of 3 coils per tumor were placed with a mean tumor-coil distance of 2.7 cm. Forty three (87.7%) of 49 coils were successfully used as fiducial markers. Two coils could not be used due to a larger tumor-coil distance (> 50 mm). Four coils were in an acceptable position but their non-coiling shape precluded tumor tracking for CyberKnife treatment. No major complications needing further medication other than nominal therapy, hospitalization more than one night or permanent adverse sequale were observed. Endovascular placement of coil as a fiducial marker is safe and feasible during CyberKnife therapy, and might be an option for the patients in which percutaneous transthoracic fiducial placement might be risky.

Comparison between whole-body and head and neck neurovascular coils for 3-T magnetic resonance proton resonance frequency shift thermography guidance in the head and neck region.

PubMed

Ginat, Daniel Thomas; Anthony, Gregory J; Christoforidis, Gregory; Oto, Aytekin; Dalag, Leonard; Sammet, Steffen

2018-02-01

The purpose of this study is to compare the image quality of magnetic resonance (MR) treatment planning images and proton resonance frequency (PRF) shift thermography images and inform coil selection for MR-guided laser ablation of tumors in the head and neck region. Laser ablation was performed on an agar phantom and monitored via MR PRF shift thermography on a 3-T scanner, following acquisition of T1-weighted (T1W) planning images. PRF shift thermography images and T2-weighted (T2W) planning images were also performed in the neck region of five normal human volunteers. Signal-to-noise ratios (SNR) and temperature uncertainty were calculated and compared between scans acquired with the quadrature mode body integrated coil and a head and neck neurovascular coil. T1W planning images of the agar phantom produced SNRs of 4.0 and 12.2 for the quadrature mode body integrated coil and head and neck neurovascular coil, respectively. The SNR of the phantom MR thermography magnitude images obtained using the quadrature mode body integrated coil was 14.4 versus 59.6 using the head and neck coil. The average temperature uncertainty for MR thermography performed on the phantom with the quadrature mode body integrated coil was 1.1 versus 0.3 °C with the head and neck coil. T2W planning images of the neck in five human volunteers produced SNRs of 28.3 and 91.0 for the quadrature mode body integrated coil and head and neck coil, respectively. MR thermography magnitude images of the neck in the volunteers obtained using the quadrature mode body integrated coil had a signal-to-noise ratio of 8.3, while the SNR using the head and neck coil was 16.1. The average temperature uncertainty for MR thermography performed on the volunteers with the body coil was 2.5 versus 1.6 °C with the head and neck neurovascular coil. The quadrature mode body integrated coil provides inferior image quality for both basic treatment planning sequences and MR PRF shift thermography compared with a neurovascular coil, but may nevertheless be adequate for clinical purposes.

Local Multi-Channel RF Surface Coil versus Body RF Coil Transmission for Cardiac Magnetic Resonance at 3 Tesla: Which Configuration Is Winning the Game?

PubMed Central

Winter, Lukas; Dieringer, Matthias A.; Els, Antje; Oezerdem, Celal; Rieger, Jan; Kuehne, Andre; Cassara, Antonino M.; Pfeiffer, Harald; Wetterling, Friedrich; Niendorf, Thoralf

2016-01-01

Introduction The purpose of this study was to demonstrate the feasibility and efficiency of cardiac MR at 3 Tesla using local four-channel RF coil transmission and benchmark it against large volume body RF coil excitation. Methods Electromagnetic field simulations are conducted to detail RF power deposition, transmission field uniformity and efficiency for local and body RF coil transmission. For both excitation regimes transmission field maps are acquired in a human torso phantom. For each transmission regime flip angle distributions and blood-myocardium contrast are examined in a volunteer study of 12 subjects. The feasibility of the local transceiver RF coil array for cardiac chamber quantification at 3 Tesla is demonstrated. Results Our simulations and experiments demonstrate that cardiac MR at 3 Tesla using four-channel surface RF coil transmission is competitive versus current clinical CMR practice of large volume body RF coil transmission. The efficiency advantage of the 4TX/4RX setup facilitates shorter repetition times governed by local SAR limits versus body RF coil transmission at whole-body SAR limit. No statistically significant difference was found for cardiac chamber quantification derived with body RF coil versus four-channel surface RF coil transmission. Our simulation also show that the body RF coil exceeds local SAR limits by a factor of ~2 when driven at maximum applicable input power to reach the whole-body SAR limit. Conclusion Pursuing local surface RF coil arrays for transmission in cardiac MR is a conceptually appealing alternative to body RF coil transmission, especially for patients with implants. PMID:27598923

Redesigning existing transcranial magnetic stimulation coils to reduce energy: application to low field magnetic stimulation

NASA Astrophysics Data System (ADS)

Wang, Boshuo; Shen, Michael R.; Deng, Zhi-De; Smith, J. Evan; Tharayil, Joseph J.; Gurrey, Clement J.; Gomez, Luis J.; Peterchev, Angel V.

2018-06-01

Objective. To present a systematic framework and exemplar for the development of a compact and energy-efficient coil that replicates the electric field (E-field) distribution induced by an existing transcranial magnetic stimulation coil. Approach. The E-field generated by a conventional low field magnetic stimulation (LFMS) coil was measured for a spherical head model and simulated in both spherical and realistic head models. Then, using a spherical head model and spatial harmonic decomposition, a spherical-shaped cap coil was synthesized such that its windings conformed to a spherical surface and replicated the E-field on the cortical surface while requiring less energy. A prototype coil was built and electrically characterized. The effect of constraining the windings to the upper half of the head was also explored via an alternative coil design. Main results. The LFMS E-field distribution resembled that of a large double-cone coil, with a peak field strength around 350 mV m‑1 in the cortex. The E-field distributions of the cap coil designs were validated against the original coil, with mean errors of 1%–3%. The cap coil required as little as 2% of the original coil energy and was significantly smaller in size. Significance. The redesigned LFMS coil is substantially smaller and more energy-efficient than the original, improving cost, power consumption, and portability. These improvements could facilitate deployment of LFMS in the clinic and potentially at home. This coil redesign approach can also be applied to other magnetic stimulation paradigms. Finally, the anatomically-accurate E-field simulation of LFMS can be used to interpret clinical LFMS data.

A switch from parallel to antiparallel strand orientation in a coiled-coil X-ray structure via two core hydrophobic mutations

DOE PAGES

Malashkevich, Vladimir N.; Higgins, Chelsea D.; Almo, Steven C.; ...

2015-05-06

The coiled-coil is one of the most ubiquitous and well studied protein structural motifs. Significant effort has been devoted to dissecting subtle variations of the typical heptad repeat sequence pattern that can designate larger topological features such as relative α-helical orientation and oligomer size. Here in this paper we report the X-ray structure of a model coiled-coil peptide, HA2-Del-L2seM, which forms an unanticipated core antiparallel dimer with potential sites for discrete higher-order multimerization (trimer or tetramer). In the X-ray structure, a third, partially-ordered α-helix is weakly associated with the antiparallel dimer and analytical ultracentrifugation experiments indicate the peptide forms amore » well-defined tetramer in solution. The HA2-Del-L2seM sequence is closely related to a parent model peptide, HA2-Del, which we previously reported adopts a parallel trimer; HA2-Del-L2seM differs by only hydrophobic leucine to selenomethione mutations and thus this subtle difference is sufficient to switch both relative α-helical topology and number of α-helices participating in the coiled-coil. Comparison of the X-ray structures of HA2-Del-L2seM (reported here) with the HA2-Del parent (reported previously) reveals novel interactions involving the selenomethionine residues that promote antiparallel coiled-coil configuration and preclude parallel trimer formation. Finally, these novel atomic insights are instructive for understanding subtle features that can affect coiled-coil topology and provide additional information for design of antiparallel coiled-coils.« less

Design of transcranial magnetic stimulation coils with optimal trade-off between depth, focality, and energy.

PubMed

Gomez, Luis J; Goetz, Stefan M; Peterchev, Angel V

2018-08-01

Transcranial magnetic stimulation (TMS) is a noninvasive brain stimulation technique used for research and clinical applications. Existent TMS coils are limited in their precision of spatial targeting (focality), especially for deeper targets. This paper presents a methodology for designing TMS coils to achieve optimal trade-off between the depth and focality of the induced electric field (E-field), as well as the energy required by the coil. A multi-objective optimization technique is used for computationally designing TMS coils that achieve optimal trade-offs between E-field focality, depth, and energy (fdTMS coils). The fdTMS coil winding(s) maximize focality (minimize the volume of the brain region with E-field above a given threshold) while reaching a target at a specified depth and not exceeding predefined peak E-field strength and required coil energy. Spherical and MRI-derived head models are used to compute the fundamental depth-focality trade-off as well as focality-energy trade-offs for specific target depths. Across stimulation target depths of 1.0-3.4 cm from the brain surface, the suprathreshold volume can be theoretically decreased by 42%-55% compared to existing TMS coil designs. The suprathreshold volume of a figure-8 coil can be decreased by 36%, 44%, or 46%, for matched, doubled, or quadrupled energy. For matched focality and energy, the depth of a figure-8 coil can be increased by 22%. Computational design of TMS coils could enable more selective targeting of the induced E-field. The presented results appear to be the first significant advancement in the depth-focality trade-off of TMS coils since the introduction of the figure-8 coil three decades ago, and likely represent the fundamental physical limit.

Influence of a heptad repeat stutter on the pH-dependent conformational behavior of the central coiled-coil from influenza hemagglutinin HA2.

PubMed

Higgins, Chelsea D; Malashkevich, Vladimir N; Almo, Steven C; Lai, Jonathan R

2014-09-01

The coiled-coil is one of the most common protein structural motifs. Amino acid sequences of regions that participate in coiled-coils contain a heptad repeat in which every third then forth residue is occupied by a hydrophobic residue. Here we examine the consequences of a "stutter," a deviation of the idealized heptad repeat that is found in the central coiled-coil of influenza hemagluttinin HA2. Characterization of a peptide containing the native stutter-containing HA2 sequence, as well as several variants in which the stutter was engineered out to restore an idealized heptad repeat pattern, revealed that the stutter is important for allowing coiled-coil formation in the WT HA2 at both neutral and low pH (7.1 and 4.5). By contrast, all variants that contained idealized heptad repeats exhibited marked pH-dependent coiled-coil formation with structures forming much more stably at low pH. A crystal structure of one variant containing an idealized heptad repeat, and comparison to the WT HA2 structure, suggest that the stutter distorts the optimal interhelical core packing arrangement, resulting in unwinding of the coiled-coil superhelix. Interactions between acidic side chains, in particular E69 and E74 (present in all peptides studied), are suggested to play a role in mediating these pH-dependent conformational effects. This conclusion is partially supported by studies on HA2 variant peptides in which these positions were altered to aspartic acid. These results provide new insight into the structural role of the heptad repeat stutter in HA2. © 2014 Wiley Periodicals, Inc.

Predicting helix orientation for coiled-coil dimers

PubMed Central

Apgar, James R.; Gutwin, Karl N.; Keating, Amy E.

2008-01-01

The alpha-helical coiled coil is a structurally simple protein oligomerization or interaction motif consisting of two or more alpha helices twisted into a supercoiled bundle. Coiled coils can differ in their stoichiometry, helix orientation and axial alignment. Because of the near degeneracy of many of these variants, coiled coils pose a challenge to fold recognition methods for structure prediction. Whereas distinctions between some protein folds can be discriminated on the basis of hydrophobic/polar patterning or secondary structure propensities, the sequence differences that encode important details of coiled-coil structure can be subtle. This is emblematic of a larger problem in the field of protein structure and interaction prediction: that of establishing specificity between closely similar structures. We tested the behavior of different computational models on the problem of recognizing the correct orientation - parallel vs. antiparallel - of pairs of alpha helices that can form a dimeric coiled coil. For each of 131 examples of known structure, we constructed a large number of both parallel and antiparallel structural models and used these to asses the ability of five energy functions to recognize the correct fold. We also developed and tested three sequenced-based approaches that make use of varying degrees of implicit structural information. The best structural methods performed similarly to the best sequence methods, correctly categorizing ∼81% of dimers. Steric compatibility with the fold was important for some coiled coils we investigated. For many examples, the correct orientation was determined by smaller energy differences between parallel and antiparallel structures distributed over many residues and energy components. Prediction methods that used structure but incorporated varying approximations and assumptions showed quite different behaviors when used to investigate energetic contributions to orientation preference. Sequence based methods were sensitive to the choice of residue-pair interactions scored. PMID:18506779

Processing and plating helical metallic coils

NASA Technical Reports Server (NTRS)

1972-01-01

The results of research efforts to develop an optimized nickel cobalt coating suitable as a recording medium are outlined. The coating is to be used directly on a BeCu helical coil substrate of a helical coil NASA recorder. Specifically, efforts were made to: optimize the coating thickness; establish processes and techniques adaptable for the production of finalized plated helical coils; design and fabricate the equipment required for production and testing of the coils; and deliver finalized helical coils to NASA.

Analysis of Coiled-Coil Interactions between Core Proteins of the Spindle Pole Body

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zizlsperger, N.; Malashkevich, V; Pillay, S

2008-01-01

The spindle pole body (SPB) is a multiprotein complex that organizes microtubules in yeast. Due to its large size and association with the nuclear membrane, little is known about its detailed structure. In particular, although many SPB components and some of the interactions between them have been identified, the molecular details of how most of these interactions occur are not known. The prevalence of predicted coiled-coil regions in SPB proteins suggests that some interactions may occur via coiled coils. Here this hypothesis is supported by biochemical characterization of isolated coiled-coil peptides derived from SPB proteins. Formation of four strongly self-associatingmore » coiled-coil complexes from Spc29, Spc42, and Spc72 was demonstrated by circular dichroism (CD) spectroscopy and a fluorescence resonance energy transfer (FRET) assay. Many weaker self- and heteroassociations were also detected by CD, FRET, and/or cross-linking. The thermal stabilities of nine candidate homooligomers were assessed; six unfolded cooperatively with melting temperatures ranging from <11 to >50 C. Solution studies established that coiled-coil peptides derived from Spc42 and Spc72 form parallel dimers, and this was confirmed for Spc42 by a high-resolution crystal structure. These data contribute to a growing body of knowledge that will ultimately provide a detailed model of the SPB structure.« less

Design and use of a folded four-ring double-tuned birdcage coil for rat brain sodium imaging at 9.4 T

NASA Astrophysics Data System (ADS)

Ha, YongHyun; Choi, Chang-Hoon; Worthoff, Wieland A.; Shymanskaya, Aliaksandra; Schöneck, Michael; Willuweit, Antje; Felder, Jörg; Shah, N. Jon

2018-01-01

A folded four-ring quadrature birdcage coil was designed and constructed with a double-tune configuration of an outer high-pass coil for 1H (400 MHz) and inner low-pass coil for 23Na (105.72 MHz at 9.4 T). The coil was evaluated on the bench and in the scanner, comparing its performance with that of single-tuned coils and a large four-ring coil. All coils were tuned and matched and the isolation between two quadrature ports was found to be better than -13.7 dB for 1H and -27 dB for 23Na. Signal-to-noise ratios (SNRs) were calculated and 23Na flip angle maps were acquired. 23Na SNR of the folded four-ring reached ∼93% of that obtained with the single-tuned coil. A set of in vivo1H and 23Na axial images to cover the whole rat brain were obtained. The performance of the folded four-ring coil and its benefit for 23Na imaging experiments have been demonstrated. This proposed four-ring coil could avoid length restrictions, e.g. the shoulders, by folding the outer rings vertically. This facilitates the construction of double-tuned four-ring birdcage coils just to fit the head, leading to higher filling factors and better SNR.

Functional Investigation of the Plant-Specific Long Coiled-Coil Proteins PAMP-INDUCED COILED-COIL (PICC) and PICC-LIKE (PICL) in Arabidopsis thaliana

PubMed Central

Venkatakrishnan, Sowmya; Mackey, David; Meier, Iris

2013-01-01

We have identified and characterized two Arabidopsis long coiled-coil proteins PAMP-INDUCED COILED-COIL (PICC) and PICC-LIKE (PICL). PICC (147 kDa) and PICL (87 kDa) are paralogs that consist predominantly of a long coiled-coil domain (expanded in PICC), with a predicted transmembrane domain at the immediate C-terminus. Orthologs of PICC and PICL were found exclusively in vascular plants. PICC and PICL GFP fusion proteins are anchored to the cytoplasmic surface of the endoplasmic reticulum (ER) membrane by a C-terminal transmembrane domain and a short tail domain, via a tail-anchoring mechanism. T-DNA-insertion mutants of PICC and PICL as well as the double mutant show an increased sensitivity to the plant abiotic stress hormone abscisic acid (ABA) in a post-germination growth response. PICC, but not PICL gene expression is induced by the bacterial pathogen-associated molecular pattern (PAMP) flg22. T-DNA insertion alleles of PICC, but not PICL, show increased susceptibility to the non-virulent strain P. syringae pv. tomato DC3000 hrcC, but not to the virulent strain P. syringae pv. tomato DC3000. This suggests that PICC mutants are compromised in PAMP-triggered immunity (PTI). The data presented here provide first evidence for the involvement of a plant long coiled-coil protein in a plant defense response. PMID:23451199

Retrieval of a Migrated Coil Using an X6 MERCI Device

PubMed Central

Hare, A. O'; Brennan, P.; Thornton, J.

2009-01-01

Summary Coil migration is a recognised but rare complication of endovascular coiling. Many techniques are available commercially for coil retrieval. We report the case of an acute subarachnoid hemorrhage in a 54-year-old woman in which a migrated coil was successfully retrieved using an X6 MERCI device. PMID:20465937

A 5.9 tesla conduction-cooled coil composed of a stack of four single pancakes wound with YBCO wide tapes

NASA Astrophysics Data System (ADS)

Iwai, Sadanori; Miyazaki, Hiroshi; Tosaka, Taizo; Tasaki, Kenji; Urata, Masami; Ioka, Shigeru; Ishii, Yusuke

2013-11-01

We have been developing a conduction-cooled coil wound with YBCO-coated conductors for HTS applications. Previously, we have fabricated a coil composed of a stack of 12 single pancakes wound with 4 mm-wide YBCO tapes. This coil had a central magnetic field as high as 5.1 T at 10 K under conduction-cooled conditions. In the present study, we fabricated and tested a coil composed of a stack of four single pancakes wound with 12 mm-wide YBCO tapes. The total size of the coil and the Jc value of the tapes were almost the same as those of the former coil. At 77 K, the voltage-current characteristics showed a high n-value of 24, confirming that the coil had no degradation. Furthermore, in a conduction-cooled configuration at 20 K to 60 K, the coil showed a high n-value of over 20. At 20 K, the central magnetic field reached 5.9 T at 903 A, which is 1.3-times higher than that of the former coil.

Magnetic resonance imaging of rodent spinal cord with an improved performance coil at 7 Tesla

NASA Astrophysics Data System (ADS)

Solis-Najera, S. E.; Rodriguez, A. O.

2014-11-01

Magnetic Resonance Imaging of animal models provide reliable means to study human diseases. The image acquisition particularly determined by the radio frequency coil to detect the signal emanated from a particular region of interest. A scaled-down version of the slotted surface coil was built based on the previous results of a magnetron-type surface coil for human applications. Our coil prototype had a 2 cm total diameter and six circular slots and was developed for murine spinal cord at 7 T. Electromagnetic simulations of the slotted and circular coils were also performed to compute the spatially dependent magnetic and electric fields using a simulated saline-solution sphere. The quality factor of both coils was experimentally measured giving a lower noise figure and a higher quality factor for the slotted coil outperforming the circular coil. Images of the spinal cord of a rat were acquired using standard pulse sequences. The slotted surface coil can be a good tool for spinal cord rat imaging using conventional pulse sequences at 7 T.

The tripartite motif coiled-coil is an elongated antiparallel hairpin dimer.

PubMed

Sanchez, Jacint G; Okreglicka, Katarzyna; Chandrasekaran, Viswanathan; Welker, Jordan M; Sundquist, Wesley I; Pornillos, Owen

2014-02-18

Tripartite motif (TRIM) proteins make up a large family of coiled-coil-containing RING E3 ligases that function in many cellular processes, particularly innate antiviral response pathways. Both dimerization and higher-order assembly are important elements of TRIM protein function, but the atomic details of TRIM tertiary and quaternary structure have not been fully understood. Here, we present crystallographic and biochemical analyses of the TRIM coiled-coil and show that TRIM proteins dimerize by forming interdigitating antiparallel helical hairpins that position the N-terminal catalytic RING domains at opposite ends of the dimer and the C-terminal substrate-binding domains at the center. The dimer core comprises an antiparallel coiled-coil with a distinctive, symmetric pattern of flanking heptad and central hendecad repeats that appear to be conserved across the entire TRIM family. Our studies reveal how the coiled-coil organizes TRIM25 to polyubiquitylate the RIG-I/viral RNA recognition complex and how dimers of the TRIM5α protein are arranged within hexagonal arrays that recognize the HIV-1 capsid lattice and restrict retroviral replication.

The tripartite motif coiled-coil is an elongated antiparallel hairpin dimer

PubMed Central

Sanchez, Jacint G.; Okreglicka, Katarzyna; Chandrasekaran, Viswanathan; Welker, Jordan M.; Sundquist, Wesley I.; Pornillos, Owen

2014-01-01

Tripartite motif (TRIM) proteins make up a large family of coiled-coil-containing RING E3 ligases that function in many cellular processes, particularly innate antiviral response pathways. Both dimerization and higher-order assembly are important elements of TRIM protein function, but the atomic details of TRIM tertiary and quaternary structure have not been fully understood. Here, we present crystallographic and biochemical analyses of the TRIM coiled-coil and show that TRIM proteins dimerize by forming interdigitating antiparallel helical hairpins that position the N-terminal catalytic RING domains at opposite ends of the dimer and the C-terminal substrate-binding domains at the center. The dimer core comprises an antiparallel coiled-coil with a distinctive, symmetric pattern of flanking heptad and central hendecad repeats that appear to be conserved across the entire TRIM family. Our studies reveal how the coiled-coil organizes TRIM25 to polyubiquitylate the RIG-I/viral RNA recognition complex and how dimers of the TRIM5α protein are arranged within hexagonal arrays that recognize the HIV-1 capsid lattice and restrict retroviral replication. PMID:24550273

The nature of thrombosis induced by platinum and tungsten coils in saccular aneurysms.

PubMed

Byrne, J V; Hope, J K; Hubbard, N; Morris, J H

1997-01-01

To compare the efficacy and biocompatability of electrolytic and mechanically detachable embolization coils of two metal types. Experimental saccular aneurysms in pigs were used to assess embolization induced by platinum or tungsten coils. Longitudinal angiographic and histologic studies were performed on treated and untreated (control) aneurysms to compare thrombosis and cellular responses after embolization with electrolytically detachable platinum coils and with mechanically detached tungsten coils. Fewer tungsten than platinum coils were needed to induce thrombosis. The inflammatory response within the aneurysmal lumen was more florid in embolized aneurysms than in control aneurysms. No difference was found in the timing or extent of accumulation of eosinophils, lymphocytes, or polymorphs between the two coils used. Giant cell responses were more marked in treated aneurysms; tungsten coils more than platinum coils. The amount of collagen and fibrosis present increased over the study period and was similar in treated and control aneurysms. The coil type influenced the initial cellular response but had little effect on the rate or degree to which blood clot within the aneurysm was replaced by fibrous tissue.

Triple Halo Coil: Development and Comparison with Other TMS Coils

NASA Astrophysics Data System (ADS)

Rastogi, Priyam; Hadimani, Ravi; Jiles, David

Transcranial Magnetic Stimulation (TMS) is a non-invasive stimulation technique that can be used for the treatment of various neurological disorders such as Parkinson's Disease, PTSD, TBI and anxiety by regulating synaptic activity. TMS is FDA approved for the treatment of major depressive disorder. There is a critical need to develop deep TMS coils that can stimulate deeper regions of the brain without excessively stimulating the cortex in order to provide an alternative to surgical methods. We have developed a novel multi-coil configuration called ``Triple Halo Coil'' (THC) that can stimulate deep brain regions. Investigation of induced electric and magnetic field in these regions have been achieved by computer modelling. Comparison of the results due to THC configuration have been conducted with other TMS coils such as ``Halo Coil'', circular coil and ``Figure of Eight'' coil. There was an improvement of more than 15 times in the strength of magnetic field, induced by THC configuration at 10 cm below the vertex of the head when compared with the ``Figure of Eight'' coil alone. Carver Charitable Trust.

Coil Design for Low Aspect Ratio Stellarators

NASA Astrophysics Data System (ADS)

Miner, W. H., Jr.; Valanju, P. M.; Wiley, J. C.; Hirshman, S. P.; Whitson, J. C.

1998-11-01

Two compact stellarator designs have recently been under investigation because of their potential as a reactor featuring steady-state, disruption-free operation, low recirculating power and good confinement and beta. Both quasi-axisymmetric (QA) equilibria and quasi-omnigenous (QO) equilibria have been obtained by using the 3-D MHD equilibrium code VMEC. In order to build an experiment, coil sets must be obtained that are compatable with these equilibria. We have been using both the NESCOIL(Merkel, P., Nucl. Fus. 27, 5 (1987) 867.) code and the COILOPT code to find coilsets for both of these types of equilibria. We are considering three types of coil configurations. The first is a combination of modular coils and vertical field coils. The second configuration is a combination of toroidal field coils, vertical field coils and saddle coils. A third configuration is a combination of modular coils and a single helical winding. The quality of each coil set will be evaluated by computing its magnetic field and using that as input to VMEC in free boundary mode to see how accurately the original equilibrium can be reconstructed.

A spiral, bi-planar gradient coil design for open magnetic resonance imaging.

PubMed

Zhang, Peng; Shi, Yikai; Wang, Wendong; Wang, Yaohui

2018-01-01

To design planar gradient coil for MRI applications without discretization of continuous current density and loop-loop connection errors. In the new design method, the coil current is represented using a spiral curve function described by just a few control parameters. Using a proper parametric equation set, an ensemble of spiral contours is reshaped to satisfy the coil design requirements, such as gradient linearity, inductance and shielding. In the given case study, by using the spiral coil design, the magnetic field errors in the imaging area were reduced from 5.19% (non-spiral design) to 4.47% (spiral design) for the transverse gradient coils, and for the longitudinal gradient coil design, the magnetic field errors were reduced to 5.02% (spiral design). The numerical evaluation shows that when compared with conventional wire loop, the inductance and resistance of spiral coil was reduced by 11.55% and 8.12% for x gradient coil, respectively. A novel spiral gradient coil design for biplanar MRI systems, the new design offers better magnetic field gradients, smooth contours than the conventional connected counterpart, which improves manufacturability.

Stabilization of Tokamak Plasmas by the Addition of Nonaxisymmetric Coils

NASA Astrophysics Data System (ADS)

Reiman, Allan

2008-11-01

It has been recognized since the early days of the fusion program that stellarator coils can be used to stabilize current carrying, toroidal, magnetically confined plasmas.[1] More recently, it has been shown that the vertical mode in a tokamak can be stabilized by a relatively simple set of parallelogram-shaped, localized, nonaxisymmetric coils.[2] We show that by superposing sets of these parallelogram-shaped, nonaxisymmetric coils at different locations, it is possible to reproduce the coil current patterns for conventional stellarator coils as well as those for Furth-Hartman coils[3]. This allows us to gain insight into the physics of stabilization produced by various sets of nonaxisymmetric coils by analysis of the effect on stability of localized coils at differing locations. In particular, the relationship between the stabilization effect and the rotational transform generated by the nonaxisymmetric coils is clarified. [1] J. L. Johnson, C. R. Oberman, R. M. Kulsrud, and E. A. Frieman, Phys. Fluids 1, 281 (1958) [2] A. Reiman, Phys. Rev. Lett. 99, 135007, (2007). [3] H.P. Furth and C.W. Hartman, Phys. Fluids 11, 408 (1968).

The Whole Elephant: A Synoptic View of Liquid Rope Coiling

NASA Astrophysics Data System (ADS)

Ribe, Neil

2016-11-01

Liquid rope coiling is the instability that occurs when e.g. a thin stream of honey is poured onto toast. While we now have a fine-grained understanding of each of the four principal coiling modes (viscous, gravitational, inertio-gravitational and inertial), we still lack a global view of how the modes cohere to form a larger whole. Using a numerical continuation procedure, I determine how the dimensionless coiling frequency depends on the dimensionless fall height and flow rate, for several values of the dimensionless nozzle diameter. Starting with the onset of coiling, I propose a purely geometrical definition of the critical surface between coiling and no coiling as the locus of points where the radius a1 of the rope at the contact point is just equal to the coil radius R. Coiling with a1 > R is impossible because the rope would intersect itself. I characterize the asymptotic limits of the critical surface as well as the structure of the supercritical volume inside that surface. The procedure reveals a new mode of coiling onset that has not yet been identified.

Mild CFTR mutations and genetic predisposition to lactase persistence in cystic fibrosis

PubMed Central

Mądry, Edyta; Fidler, Ewa; Sobczyńska-Tomaszewska, Agnieszka; Lisowska, Aleksandra; Krzyżanowska, Patrycja; Pogorzelski, Andrzej; Minarowski, Łukasz; Oralewska, Beata; Mojs, Ewa; Sapiejka, Ewa; Marciniak, Ryszard; Sands, Dorota; Korzon-Burakowska, Anna; Kwiecień, Jarosław; Walkowiak, Jarosław

2011-01-01

Taking into account the reported incidence of hypolactasia in cystic fibrosis (CF) and the possible impact of milk products on nutritional status we aimed to assess the genetic predisposition to adult-type hypolactasia (ATH) and its incidence in CF. Single nucleotide polymorphism upstream of the lactase gene (LCT) was assessed in 289 CF patients. In subject with −13910C/C genotype (C/C) predisposing to ATH, hydrogen-methane breath test (BT) with lactose loading was conducted and clinical symptoms typical for lactose malabsorption were assessed. The percentage of CF patients with C/C was similar to that observed in healthy subjects (HS) (31.5 vs 32.5% ). Eleven out of 52 (24.5%) CF C/C patients had abnormal BT results. The recalculated frequency of lactose malabsorption was similar for the entire CF and HS populations (6.9 vs 7.2%). Similarly as in the control group, few CF patients have identified and linked to lactose consumption clinical symptoms. The frequency of LCT polymorphic variants in CF patients having and not having severe mutations of CFTR gene showed significant differences. The C allele was more frequent in homozygotes of the severe mutations than in patients carrying at least one mild/unknown mutation (P<0.0028) and in patients with at least one mild mutation (P<0.0377). In conclusion, CF patients carrying mild CFTR mutations seem to have lower genetic predisposition to ATH. Lactose malabsorption due to ATH in CF is not more frequent than in the general population. Symptomatic assessment of lactose malabsorption in CF is not reliable. PMID:21407263

Optimized self nano-emulsifying systems of ezetimibe with enhanced bioavailability potential using long chain and medium chain triglycerides.

PubMed

Bandyopadhyay, Shantanu; Katare, O P; Singh, Bhupinder

2012-12-01

The objective of the current work is to develop systematically optimized self-nanoemulsifying drug delivery systems (SNEDDS) using long chain triglycerides (LCT's) and medium chain triglycerides (MCT's) of ezetimibe employing Formulation by Design (FbD), and evaluate their in vitro and in vivo performance. Equilibrium solubility studies indicated the choice of Maisine 35-1 and Capryol 90 as lipids, and of Labrasol and Tween 80 as emulgents for formulating the LCT and MCT systems, respectively. Ternary phase diagrams were constructed to select the areas of nanoemulsion, and the amounts of lipid (X(1)) and emulgent (X(2)) as the critical factor variables. The SNEDDS were systematically optimized using 3(2) central composite design and the optimized formulations located using overlay plot. TEM studies on reconstituted SNEDDS demonstrated uniform shape and size of globules. The nanometer size range and high negative values of zeta potential depicted non-coalescent nature of the optimized SNEDDS. Thermodynamic studies, cloud point determination and accelerated stability studies ascertained the stability of optimized formulations. In situ perfusion (SPIP) studies in Sprague Dawley (SD) rats construed remarkable enhancement in the absorptivity and permeability parameters of SNEDDS vis-à-vis the conventional marketed product. In vivo pharmacodynamic studies in SD rats indicated significantly superior modification in plasma lipid levels of optimized SNEDDS vis-à-vis marketed product, inclusion complex and pure drug. The studies, therefore, indicate the successful formulation development of self-nanoemulsifying systems with distinctly improved bioavailability potential of ezetimibe. Copyright © 2012 Elsevier B.V. All rights reserved.

Positive selection of lactase persistence among people of Southern Arabia.

PubMed

Bayoumi, Riad; De Fanti, Sara; Sazzini, Marco; Giuliani, Cristina; Quagliariello, Andrea; Bortolini, Eugenio; Boattini, Alessio; Al-Habori, Molham; Al-Zubairi, Adel Sharaf; Rose, Jeffrey I; Romeo, Giovanni; Al-Abri, Abdulrahim; Luiselli, Donata

2016-12-01

Frequency patterns of the lactase persistence (LP)-associated -13,915 G allele and archaeological records pointing to substantial role played by southern regions in the peopling and domestication processes that involved the Arabian Peninsula suggest that Southern Arabia plausibly represented the center of diffusion of such adaptive variant. Nevertheless, a well-defined scenario for evolution of Arabian LP is still to be elucidated and the burgeoning archaeological picture of complex human migrations occurred through the peninsula is not matched by an equivalent high-resolution description of genetic variation underlying this adaptive trait. To fill this gap, we investigated diversity at a wide genomic interval surrounding the LCT gene in different Southern Arabian populations. 40 SNPs were genotyped to characterize LCT profiles of 630 Omani and Yemeni individuals to perform population structure, linkage disequilibrium, population differentiation-based and haplotype-based analyses. Typical Arabian LP-related variation was found in Dhofaris and Yemenis, being characterized by private haplotypes carrying the -13,915 G allele, unusual differentiation with respect to northern groups and conserved homozygous haplotype-blocks, suggesting that the adaptive allele was likely introduced in the Arabian gene pool in southern populations and was then subjected to prolonged selective pressure. By pointing to Yemen as one of the best candidate centers of diffusion of the Arabian-specific adaptive variant, obtained results indicate the spread of indigenous groups as the main process underlying dispersal of LP along the Arabian Peninsula, supporting a refugia model for Arabian demic movements occurred during the Terminal Pleistocene and Early Holocene. © 2016 Wiley Periodicals, Inc.

Traces of sub-Saharan and Middle Eastern lineages in Indian Muslim populations

PubMed Central

Eaaswarkhanth, Muthukrishnan; Haque, Ikramul; Ravesh, Zeinab; Romero, Irene Gallego; Meganathan, Poorlin Ramakodi; Dubey, Bhawna; Khan, Faizan Ahmed; Chaubey, Gyaneshwer; Kivisild, Toomas; Tyler-Smith, Chris; Singh, Lalji; Thangaraj, Kumarasamy

2010-01-01

Islam is the second most practiced religion in India, next to Hinduism. It is still unclear whether the spread of Islam in India has been only a cultural transformation or is associated with detectable levels of gene flow. To estimate the contribution of West Asian and Arabian admixture to Indian Muslims, we assessed genetic variation in mtDNA, Y-chromosomal and LCT/MCM6 markers in 472, 431 and 476 samples, respectively, representing six Muslim communities from different geographical regions of India. We found that most of the Indian Muslim populations received their major genetic input from geographically close non-Muslim populations. However, low levels of likely sub-Saharan African, Arabian and West Asian admixture were also observed among Indian Muslims in the form of L0a2a2 mtDNA and E1b1b1a and J*(xJ2) Y-chromosomal lineages. The distinction between Iranian and Arabian sources was difficult to make with mtDNA and the Y chromosome, as the estimates were highly correlated because of similar gene pool compositions in the sources. In contrast, the LCT/MCM6 locus, which shows a clear distinction between the two sources, enabled us to rule out significant gene flow from Arabia. Overall, our results support a model according to which the spread of Islam in India was predominantly cultural conversion associated with minor but still detectable levels of gene flow from outside, primarily from Iran and Central Asia, rather than directly from the Arabian Peninsula. PMID:19809480

Traces of sub-Saharan and Middle Eastern lineages in Indian Muslim populations.

PubMed

Eaaswarkhanth, Muthukrishnan; Haque, Ikramul; Ravesh, Zeinab; Romero, Irene Gallego; Meganathan, Poorlin Ramakodi; Dubey, Bhawna; Khan, Faizan Ahmed; Chaubey, Gyaneshwer; Kivisild, Toomas; Tyler-Smith, Chris; Singh, Lalji; Thangaraj, Kumarasamy

2010-03-01

Islam is the second most practiced religion in India, next to Hinduism. It is still unclear whether the spread of Islam in India has been only a cultural transformation or is associated with detectable levels of gene flow. To estimate the contribution of West Asian and Arabian admixture to Indian Muslims, we assessed genetic variation in mtDNA, Y-chromosomal and LCT/MCM6 markers in 472, 431 and 476 samples, respectively, representing six Muslim communities from different geographical regions of India. We found that most of the Indian Muslim populations received their major genetic input from geographically close non-Muslim populations. However, low levels of likely sub-Saharan African, Arabian and West Asian admixture were also observed among Indian Muslims in the form of L0a2a2 mtDNA and E1b1b1a and J(*)(xJ2) Y-chromosomal lineages. The distinction between Iranian and Arabian sources was difficult to make with mtDNA and the Y chromosome, as the estimates were highly correlated because of similar gene pool compositions in the sources. In contrast, the LCT/MCM6 locus, which shows a clear distinction between the two sources, enabled us to rule out significant gene flow from Arabia. Overall, our results support a model according to which the spread of Islam in India was predominantly cultural conversion associated with minor but still detectable levels of gene flow from outside, primarily from Iran and Central Asia, rather than directly from the Arabian Peninsula.

Effects of Space Environment on Genome, Transcriptome, and Proteome of Klebsiella pneumoniae.

PubMed

Guo, Yinghua; Li, Jia; Liu, Jinwen; Wang, Tong; Li, Yinhu; Yuan, Yanting; Zhao, Jiao; Chang, De; Fang, Xiangqun; Li, Tianzhi; Wang, Junfeng; Dai, Wenkui; Fang, Chengxiang; Liu, Changting

2015-11-01

The aim of this study was to explore the effects of space flight on Klebsiella pneumoniae. A strain of K. pneumoniae was sent to space for 398 h aboard the ShenZhou VIII spacecraft during November 1, 2011-November 17, 2011. At the same time, a ground simulation with similar temperature conditions during the space flight was performed as a control. After the space mission, the flight and control strains were analyzed using phenotypic, genomic, transcriptomic and proteomic techniques. The flight strains LCT-KP289 exhibited a higher cotrimoxazole resistance level and changes in metabolism relative to the ground control strain LCT-KP214. After the space flight, 73 SNPs and a plasmid copy number variation were identified in the flight strain. Based on the transcriptomic analysis, there are 232 upregulated and 1879 downregulated genes, of which almost all were for metabolism. Proteomic analysis revealed that there were 57 upregulated and 125 downregulated proteins. These differentially expressed proteins had several functions that included energy production and conversion, carbohydrate transport and metabolism, translation, ribosomal structure and biogenesis, posttranslational modification, protein turnover, and chaperone functions. At a systems biology level, the ytfG gene had a synonymous mutation that resulted in significantly downregulated expression at both transcriptomic and proteomic levels. The mutation of the ytfG gene may influence fructose and mannose metabolic processes of K. pneumoniae during space flight, which may be beneficial to the field of space microbiology, providing potential therapeutic strategies to combat or prevent infection in astronauts. Copyright © 2015 IMSS. Published by Elsevier Inc. All rights reserved.

Octachlorodipropyl ether (s-2) mosquito coils are inadequately studied for residential use in Asia and illegal in the United States.

PubMed Central

Krieger, Robert I; Dinoff, Travis M; Zhang, Xiaofei

2003-01-01

Children and their parents in residences are often protected by insecticides from nuisance and disease-bearing mosquitoes. The annual worldwide consumption of the four major types of residential insecticide products--aerosols, mosquito coils, liquid vaporizers, and vaporizing mats--is in the billions of units. Mosquito coils are burned indoors and outdoors in East Asia and to a limited extent in other parts of the world, including the United States. Coils consist of an insecticide/repellant, organic fillers capable of burning with smoldering, binder, and additives such as synergists, dyes, and fungicide. The number of coil users in China is in the millions. In Indonesia alone, an estimated seven billion coils are purchased annually. Coils containing pyrethroid insecticides, particularly d-allethrin, may contain octachlorodipropyl ether (S-2, S-421) as a synergist or active ingredient. Use of those coils likely exposes children and adults to some level of bis(chloromethyl)ether (BCME). BCME is formed from formaldehyde and hydrogen chloride, combustion products formed from the slow smoldering (about 8 hr/coil) of the mosquito coils. Because BCME is an extremely potent lung carcinogen, the nature and extent of prolonged exposures that recur in homes during the mosquito season in tropical regions must be evaluated with respect to health. In a small analytical study, coils purchased in Indonesia and in the United States contained highly variable amounts of S-2. Some coils that contained S-2 were not labeled, making it impossible for consumers to make an informed decision about coil contents. Mosquito coils containing S-2 are unregistered, and their use is illegal in the United States. Indoor air monitoring under conditions that represent conditions of use in tropical settings and epidemiology to assess health impacts of coil use are essential to permit responsible regulatory decisions regarding continuing S-2 use. PMID:12948880

Coil End Parts Development Using BEND and Design for MQXF by LARP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Miao; Ambrosio, G.; Bermudez, S. Izquierdo

2016-09-06

End parts are critical components for saddle-shaped coils. They have a structural function where the cables are deformed in order to cross over the magnet aperture. Based on the previous design of the US LARP program for 90 mm aperture quadrupoles (TQ/LQ) and 120 mm aperture quadrupoles (HQ/LHQ) using BEND, the coil ends of the low-β quadruples (MQXF) for the HiLumi LHC upgrade were developed. This paper shows the design of the MQXF coil ends, the analysis of the coil ends during the coil fabrication, the autopsy analysis of the coil ends and the feedback to BEND parameters.

Coiling of viscous jets

NASA Astrophysics Data System (ADS)

Ribe, Neil M.

2004-11-01

A stream of viscous fluid falling from a sufficient height onto a surface forms a series of regular coils. I use a numerical model for a deformable fluid thread to predict the coiling frequency as a function of the thread's radius, the flow rate, the fall height, and the fluid viscosity. Three distinct modes of coiling can occur: viscous (e.g. toothpaste), gravitational (honey falling from a moderate height) and inertial (honey falling from a great height). When inertia is significant, three states of steady coiling with different frequencies can exist over a range of fall heights. The numerically predicted coiling frequencies agree well with experimental measurements in the inertial coiling regime.

Six pole/eight pole single-phase motor

DOEpatents

Kirschbaum, Herbert S.

1984-01-01

A single phase alternating current electric motor is provided with a main stator winding having two coil groups which are connected to form eight poles for eight-pole operation and to form six poles for six-pole operation. Each group contains four series connected coil elements with each element spanning approximately one-seventh of the periphery of the machine. The coil groups are spaced 180 mechanical degrees apart such that each end coil of one group overlaps one of the end coils of the other group. An auxiliary stator winding having two coil groups with the same relative angular displacement as the main stator winding coil groups is included.

Note: High turn density magnetic coils with improved low pressure water cooling for use in atom optics.

PubMed

McKay Parry, Nicholas; Baker, Mark; Neely, Tyler; Carey, Thomas; Bell, Thomas; Rubinsztein-Dunlop, Halina

2014-08-01

We describe a magnetic coil design utilizing concentrically wound electro-magnetic insulating (EMI) foil (25.4 μm Kapton backing and 127 μm thick layers). The magnetic coils are easily configurable for different coil sizes, while providing large surfaces for low-pressure (0.12 bar) water cooling. The coils have turn densities of ~5 mm(-1) and achieve a maximum of 377 G at 2.1 kW driving power, measured at a distance 37.9 mm from the axial center of the coil. The coils achieve a steady-state temperature increase of 36.7°C/kW.

Catalytic chemical vapor deposition synthesis and electron microscopy observation of coiled carbon nanotubes

NASA Astrophysics Data System (ADS)

Xie, Jining; Mukhopadyay, K.; Yadev, J.; Varadan, V. K.

2003-10-01

Coiled carbon nanotubes exhibit excellent mechanical and electrical properties because of the combination of coil morphology and properties of nanotubes. They could have potential novel applications in nanocomposites and nano-electronic devices as well as nano-electromechanical systems. In this work, synthesis of regularly coiled carbon nanotubes is presented. It involves pyrolysis of hydrocarbon gas over metal/support catalyst by both thermal filament and microwave catalytic chemical vapor deposition methods. Scanning electron microscopy and transmission electron microscopy were performed to observe the coil morphology and nanostructure of coiled nanotubes. The growth mechanism and structural and electrical properties of coiled carbon nanotubes are also discussed.

Six pole/eight pole single-phase motor

DOEpatents

Kirschbaum, H.S.

1984-07-31

A single phase alternating current electric motor is provided with a main stator winding having two coil groups which are connected to form eight poles for eight-pole operation and to form six poles for six-pole operation. Each group contains four series connected coil elements with each element spanning approximately one-seventh of the periphery of the machine. The coil groups are spaced 180 mechanical degrees apart such that each end coil of one group overlaps one of the end coils of the other group. An auxiliary stator winding having two coil groups with the same relative angular displacement as the main stator winding coil groups is included. 10 figs.

Comparison of the induced fields using different coil configurations during deep transcranial magnetic stimulation

PubMed Central

Ueno, Shoogo

2017-01-01

Stimulation of deeper brain structures by transcranial magnetic stimulation (TMS) plays a role in the study of reward and motivation mechanisms, which may be beneficial in the treatment of several neurological and psychiatric disorders. However, electric field distributions induced in the brain by deep transcranial magnetic stimulation (dTMS) are still unknown. In this paper, the double cone coil, H-coil and Halo-circular assembly (HCA) coil which have been proposed for dTMS have been numerically designed. The distributions of magnetic flux density, induced electric field in an anatomically based realistic head model by applying the dTMS coils were numerically calculated by the impedance method. Results were compared with that of standard figure-of-eight (Fo8) coil. Simulation results show that double cone, H- and HCA coils have significantly deep field penetration compared to the conventional Fo8 coil, at the expense of induced higher and wider spread electrical fields in superficial cortical regions. Double cone and HCA coils have better ability to stimulate deep brain subregions compared to that of the H-coil. In the mean time, both double cone and HCA coils increase risk for optical nerve excitation. Our results suggest although the dTMS coils offer new tool with potential for both research and clinical applications for psychiatric and neurological disorders associated with dysfunctions of deep brain regions, the selection of the most suitable coil settings for a specific clinical application should be based on a balanced evaluation between stimulation depth and focality. PMID:28586349

Radio aneurysm coils for noninvasive detection of cerebral embolization failures: a preliminary study.

PubMed

Mohammadi, Abdolreza Rashidi; Chen, Keqin; Ali, Mohamed Sultan Mohamed; Takahata, Kenichi

2011-12-15

The rupture of a cerebral aneurysm is the most common cause of subarachnoid hemorrhage. Endovascular embolization of the aneurysms by implantation of Guglielmi detachable coils (GDC) has become a major treatment approach in the prevention of a rupture. Implantation of the coils induces formation of tissues over the coils, embolizing the aneurysm. However, blood entry into the coiled aneurysm often occurs due to failures in the embolization process. Current diagnostic methods used for aneurysms, such as X-ray angiography and computer tomography, are ineffective for continuous monitoring of the disease and require extremely expensive equipment. Here we present a novel technique for wireless monitoring of cerebral aneurysms using implanted embolization coils as radiofrequency resonant sensors that detect the blood entry. The experiments show that commonly used embolization coils could be utilized as electrical inductors or antennas. As the blood flows into a coil-implanted aneurysm, parasitic capacitance of the coil is modified because of the difference in permittivity between the blood and the tissues grown around the coil, resulting in a change in the coil's resonant frequency. The resonances of platinum GDC-like coils embedded in aneurysm models are detected to show average responses of 224-819 MHz/ml to saline injected into the models. This preliminary demonstration indicates a new possibility in the use of implanted GDC as a wireless sensor for embolization failures, the first step toward realizing long-term, noninvasive, and cost-effective remote monitoring of cerebral aneurysms treated with coil embolization. Copyright © 2011 Elsevier B.V. All rights reserved.

A six-channel pediatric coil array for detection of children spinal pathologies by MRI at 1.5 Tesla

NASA Astrophysics Data System (ADS)

López Terrones, Marcos Alonso; Solís-Nájera, Sergio Enrique

2014-11-01

Nowadays, magnetic resonance (MR) in Mexico has become a standard technique for clinical imaging. Although most of the times the MR systems contain only coils oriented for adults. Radiologists use these coils for children studies due to the non-availability of pediatric coils. Image quality is decreased due to the low signal to noise ratio delivered to the system. The development of RF coils is always focused towards increasing SNR and optimizing the RF penetration into the sample. Moreover, spinal pathologies in children, which are an important topic in pediatric care, cover congenital and neuromuscular disorders that occur in childhood. In this work, the design of a dedicated six-channel coil for detection of spinal pathologies at 1.5 Tesla is addressed. Numerical electromagnetic simulations were performed in order to evaluate their magnetic field performance at (63.6 MHz) 1.5 Tesla. The magnetic field uniformity as well as the RF penetration depth of the coil configurations was evaluated in order to find the best/optimized coil array configuration. The coil is comprised of three rows, one with 4 coil elements and two with only one coil element. Phantom and in vivo images were acquired with the six-channel pediatric coil array. The phantom images agree with the simulated data. In vivo images acquired with the 6-channel pediatric coil array have shown very good penetration depth and homogeneity, which allow better image quality throughout the whole FOV. In addition, the parallel imaging capabilities of the array allow the acceleration of the experiments avoiding possible motion artifacts.

Design and Optimization of a 3-Coil Inductive Link for Efficient Wireless Power Transmission.

PubMed

Kiani, Mehdi; Jow, Uei-Ming; Ghovanloo, Maysam

2011-07-14

Inductive power transmission is widely used to energize implantable microelectronic devices (IMDs), recharge batteries, and energy harvesters. Power transfer efficiency (PTE) and power delivered to the load (PDL) are two key parameters in wireless links, which affect the energy source specifications, heat dissipation, power transmission range, and interference with other devices. To improve the PTE, a 4-coil inductive link has been recently proposed. Through a comprehensive circuit based analysis that can guide a design and optimization scheme, we have shown that despite achieving high PTE at larger coil separations, the 4-coil inductive links fail to achieve a high PDL. Instead, we have proposed a 3-coil inductive power transfer link with comparable PTE over its 4-coil counterpart at large coupling distances, which can also achieve high PDL. We have also devised an iterative design methodology that provides the optimal coil geometries in a 3-coil inductive power transfer link. Design examples of 2-, 3-, and 4-coil inductive links have been presented, and optimized for 13.56 MHz carrier frequency and 12 cm coupling distance, showing PTEs of 15%, 37%, and 35%, respectively. At this distance, the PDL of the proposed 3-coil inductive link is 1.5 and 59 times higher than its equivalent 2- and 4-coil links, respectively. For short coupling distances, however, 2-coil links remain the optimal choice when a high PDL is required, while 4-coil links are preferred when the driver has large output resistance or small power is needed. These results have been verified through simulations and measurements.

Intra-coil interactions in split gradient coils in a hybrid MRI-LINAC system.

PubMed

Tang, Fangfang; Freschi, Fabio; Sanchez Lopez, Hector; Repetto, Maurizio; Liu, Feng; Crozier, Stuart

2016-04-01

An MRI-LINAC system combines a magnetic resonance imaging (MRI) system with a medical linear accelerator (LINAC) to provide image-guided radiotherapy for targeting tumors in real-time. In an MRI-LINAC system, a set of split gradient coils is employed to produce orthogonal gradient fields for spatial signal encoding. Owing to this unconventional gradient configuration, eddy currents induced by switching gradient coils on and off may be of particular concern. It is expected that strong intra-coil interactions in the set will be present due to the constrained return paths, leading to potential degradation of the gradient field linearity and image distortion. In this study, a series of gradient coils with different track widths have been designed and analyzed to investigate the electromagnetic interactions between coils in a split gradient set. A driving current, with frequencies from 100 Hz to 10 kHz, was applied to study the inductive coupling effects with respect to conductor geometry and operating frequency. It was found that the eddy currents induced in the un-energized coils (hereby-referred to as passive coils) positively correlated with track width and frequency. The magnetic field induced by the eddy currents in the passive coils with wide tracks was several times larger than that induced by eddy currents in the cold shield of cryostat. The power loss in the passive coils increased with the track width. Therefore, intra-coil interactions should be included in the coil design and analysis process. Copyright © 2016 Elsevier Inc. All rights reserved.

Surgical management of an ACM aneurysm eight years after coiling.

PubMed

Pogády, P; Fellner, F; Trenkler, J; Wurm, G

2007-04-01

The authors present a case report on rebleeding of a medial cerebral aneurysm (MCA) eight years after complete endovascular coiling. The primarily successfully coiled MCA aneurysm showed a local regrowth which, however, was not the source of the rebleeding. The angiogram demonstrated no evidence of contrast filling of the coiled segment, but according to intraoperative findings (haematoma location, displacement of coils, evident place of rupture) there is no doubt that the coiled segment of the aneurysm was responsible for the haemorrhage.

Three-axis orthogonal transceiver coil for eddy current sounding

NASA Astrophysics Data System (ADS)

Sukhanov, D.; Zavyalova, K.; Goncharik, M.

2017-08-01

We propose the new structure of three-axis transceiver magnetic-induction coil for eddy current probing. Due to the orientation of the coils, the direct signal from the transmitting coil to the receiving coil is minimized, which provided a high dynamic range. Sensitivity in all directions is provided by combining coils of different orientations. Numerical simulation and experimental studies of such a system have been carried out and confirmed the applicability of the proposed method and the mathematical model.

Dual coil ignition system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huberts, Garlan J.; Qu, Qiuping; Czekala, Michael Damian

2017-03-28

A dual coil ignition system is provided. The dual coil ignition system includes a first inductive ignition coil including a first primary winding and a first secondary winding, and a second inductive ignition coil including a second primary winding and a second secondary winding, the second secondary winding connected in series to the first secondary winding. The dual coil ignition system further includes a diode network including a first diode and a second diode connected between the first secondary winding and the second secondary winding.

In vivo MR imaging of the human skin at subnanoliter resolution using a superconducting surface coil at 1.5 Tesla.

PubMed

Laistler, Elmar; Poirier-Quinot, Marie; Lambert, Simon A; Dubuisson, Rose-Marie; Girard, Olivier M; Moser, Ewald; Darrasse, Luc; Ginefri, Jean-Christophe

2015-02-01

To demonstrate the feasibility of a highly sensitive superconducting surface coil for microscopic MRI of the human skin in vivo in a clinical 1.5 Tesla (T) scanner. A 12.4-mm high-temperature superconducting coil was used at 1.5T for phantom and in vivo skin imaging. Images were inspected to identify fine anatomical skin structures. Signal-to-noise ratio (SNR) improvement by the high-temperature superconducting (HTS) coil, as compared to a commercial MR microscopy coil was quantified from phantom imaging; the gain over a geometrically identical coil made from copper (cooled or not) was theoretically deduced. Noise sources were identified to evaluate the potential of HTS coils for future studies. In vivo skin images with isotropic 80 μm resolution were demonstrated revealing fine anatomical structures. The HTS coil improved SNR by a factor 32 over the reference coil in a nonloading phantom. For calf imaging, SNR gains of 380% and 30% can be expected over an identical copper coil at room temperature and 77 K, respectively. The high sensitivity of HTS coils allows for microscopic imaging of the skin at 1.5T and could serve as a tool for dermatology in a clinical setting. © 2013 Wiley Periodicals, Inc.

Safety of Radioembolization with {sup 90}Yttrium Resin Microspheres Depending on Coiling or No-Coiling of Aberrant/High-Risk Vessels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paprottka, P. M., E-mail: philipp.paprottka@med.lmu.de, E-mail: philipp.paprottka@med.uni-muenchen.de; Paprottka, K. J., E-mail: karolin.paprottka@med.lmu.de; Walter, A., E-mail: alexandra.Walter@campus.lmu.de

2015-08-15

PurposeTo evaluate the safety of radioembolization (RE) with {sup 90}Yttrium ({sup 90}Y) resin microspheres depending on coiling or no-coiling of aberrant/high-risk vessels.Materials and MethodsEarly and late toxicity after 566 RE procedures were analyzed retrospectively in accordance with the National Cancer Institute’s Common Terminology Criteria for Adverse Events (CTCAE v3.0). For optimal safety, aberrant vessels were either coil embolized (n = 240/566, coiling group) or a more peripheral position of the catheter tip was chosen to treat right or left liver lobes (n = 326/566, no-coiling group).ResultsClinically relevant late toxicities (≥Grade 3) were observed in 1 % of our overall cohort. The no-coiling group had significantlymore » less “any” (P = 0.0001) or “clinically relevant” (P = 0.0003) early toxicity. There was no significant difference (P > 0.05) in delayed toxicity in the coiling versus the no-coiling group. No RE-induced liver disease was noted after all 566 procedures.ConclusionRE with {sup 90}Y resin microspheres is a safe and effective treatment option. Performing RE without coil embolization of aberrant vessels prior to treatment could be an alternative for experienced centers.« less

Spiral Gradient Coil Design for Use in Cylindrical MRI Systems.

PubMed

Wang, Yaohui; Xin, Xuegang; Liu, Feng; Crozier, Stuart

2018-04-01

In magnetic resonance imaging, the stream function based method is commonly used in the design of gradient coils. However, this method can be prone to errors associated with the discretization of continuous current density and wire connections. In this paper, we propose a novel gradient coil design scheme that works directly in the wire space, avoiding the system errors that may appear in the stream function approaches. Specifically, the gradient coil pattern is described with dedicated spiral functions adjusted to allow the coil to produce the required field gradients in the imaging area, minimal stray field, and other engineering terms. The performance of a designed spiral gradient coil was compared with its stream-function counterpart. The numerical evaluation shows that when compared with the conventional solution, the inductance and resistance was reduced by 20.9 and 10.5%, respectively. The overall coil performance (evaluated by the figure of merit (FoM)) was improved up to 26.5% for the x -gradient coil design; for the z-gradient coil design, the inductance and resistance were reduced by 15.1 and 6.7% respectively, and the FoM was increased by 17.7%. In addition, by directly controlling the wire distributions, the spiral gradient coil design was much sparser than conventional coils.

Designing gradient coils with reduced hot spot temperatures.

PubMed

While, Peter T; Forbes, Larry K; Crozier, Stuart

2010-03-01

Gradient coil temperature is an important concern in the design and construction of MRI scanners. Closely spaced gradient coil windings cause temperature hot spots within the system as a result of Ohmic heating associated with large current being driven through resistive material, and can strongly affect the performance of the coils. In this paper, a model is presented for predicting the spatial temperature distribution of a gradient coil, including the location and extent of temperature hot spots. Subsequently, a method is described for designing gradient coils with improved temperature distributions and reduced hot spot temperatures. Maximum temperature represents a non-linear constraint and a relaxed fixed point iteration routine is proposed to adjust coil windings iteratively to minimise this coil feature. Several examples are considered that assume different thermal material properties and cooling mechanisms for the gradient system. Coil winding solutions are obtained for all cases considered that display a considerable drop in hot spot temperature (>20%) when compared to standard minimum power gradient coils with equivalent gradient homogeneity, efficiency and inductance. The method is semi-analytical in nature and can be adapted easily to consider other non-linear constraints in the design of gradient coils or similar systems. Crown Copyright (c) 2009. Published by Elsevier Inc. All rights reserved.

Optimized Geometry for Superconducting Sensing Coils

NASA Technical Reports Server (NTRS)

Eom, Byeong Ho; Pananen, Konstantin; Hahn, Inseob

2008-01-01

An optimized geometry has been proposed for superconducting sensing coils that are used in conjunction with superconducting quantum interference devices (SQUIDs) in magnetic resonance imaging (MRI), magnetoencephalography (MEG), and related applications in which magnetic fields of small dipoles are detected. In designing a coil of this type, as in designing other sensing coils, one seeks to maximize the sensitivity of the detector of which the coil is a part, subject to geometric constraints arising from the proximity of other required equipment. In MRI or MEG, the main benefit of maximizing the sensitivity would be to enable minimization of measurement time. In general, to maximize the sensitivity of a detector based on a sensing coil coupled with a SQUID sensor, it is necessary to maximize the magnetic flux enclosed by the sensing coil while minimizing the self-inductance of this coil. Simply making the coil larger may increase its self-inductance and does not necessarily increase sensitivity because it also effectively increases the distance from the sample that contains the source of the signal that one seeks to detect. Additional constraints on the size and shape of the coil and on the distance from the sample arise from the fact that the sample is at room temperature but the coil and the SQUID sensor must be enclosed within a cryogenic shield to maintain superconductivity.

Development of Ground Coils with Low Eddy Current Loss by Applying the Compression Molding Method after the Coil Winding

NASA Astrophysics Data System (ADS)

Suzuki, Masao; Aiba, Masayuki; Takahashi, Noriyuki; Ota, Satoru; Okada, Shigenori

In a magnetically levitated transportation (MAGLEV) system, a huge number of ground coils will be required because they must be laid for the whole line. Therefore, stable performance and reduced cost are essential requirements for the ground coil development. On the other hand, because the magnetic field changes when the superconducting magnet passes by, an eddy current will be generated in the conductor of the ground coil and will result in energy loss. The loss not only increases the magnetic resistance for the train running but also brings an increase in the ground coil temperature. Therefore, the reduction of the eddy current loss is extremely important. This study examined ground coils in which both the eddy current loss and temperature increase were small. Furthermore, quantitative comparison for the eddy current loss of various magnet wire samples was performed by bench test. On the basis of the comparison, a round twisted wire having low eddy current loss was selected as an effective ground coil material. In addition, the ground coils were manufactured on trial. A favorable outlook to improve the size accuracy of the winding coil and uneven thickness of molded resin was obtained without reducing the insulation strength between the coil layers by applying a compression molding after winding.

Internal split field generator

DOEpatents

Thundat,; George, Thomas [Knoxville, TN; Van Neste, Charles W [Kingston, TN; Vass, Arpad Alexander [Oak Ridge, TN

2012-01-03

A generator includes a coil of conductive material. A stationary magnetic field source applies a stationary magnetic field to the coil. An internal magnetic field source is disposed within a cavity of the coil to apply a moving magnetic field to the coil. The stationary magnetic field interacts with the moving magnetic field to generate an electrical energy in the coil.

Auxiliary coil controls temperature of RF induction heater

NASA Technical Reports Server (NTRS)

1966-01-01

Auxiliary coil controls the temperature of an RF induction furnace that is powered by a relatively unstable RF generator. Manual or servoed adjustments of the relative position of the auxiliary coil, which is placed in close proximity to the RF coil, changes the looseness of the RF coil and hence the corresponding heating effect of its RF field.

Mathematic analysis of incremental packing density with detachable coils: does that last coil matter much?

PubMed

Taussky, P; Kallmes, D F; Cloft, H

2012-05-01

Higher packing attenuation of coils in cerebral aneurysms is associated with a decreased recurrence rate. However, geometric relationships suggest that an additional coil may have very little effect on packing attenuation as aneurysm size increases. We mathematically evaluated the relationship between aneurysm size and incremental packing attenuation for coils currently available.

A 32-channel lattice transmission line array for parallel transmit and receive MRI at 7 tesla.

PubMed

Adriany, Gregor; Auerbach, Edward J; Snyder, Carl J; Gözübüyük, Ark; Moeller, Steen; Ritter, Johannes; Van de Moortele, Pierre-François; Vaughan, Tommy; Uğurbil, Kâmil

2010-06-01

Transmit and receive RF coil arrays have proven to be particularly beneficial for ultra-high-field MR. Transmit coil arrays enable such techniques as B(1) (+) shimming to substantially improve transmit B(1) homogeneity compared to conventional volume coil designs, and receive coil arrays offer enhanced parallel imaging performance and SNR. Concentric coil arrangements hold promise for developing transceiver arrays incorporating large numbers of coil elements. At magnetic field strengths of 7 tesla and higher where the Larmor frequencies of interest can exceed 300 MHz, the coil array design must also overcome the problem of the coil conductor length approaching the RF wavelength. In this study, a novel concentric arrangement of resonance elements built from capacitively-shortened half-wavelength transmission lines is presented. This approach was utilized to construct an array with whole-brain coverage using 16 transceiver elements and 16 receive-only elements, resulting in a coil with a total of 16 transmit and 32 receive channels. (c) 2010 Wiley-Liss, Inc.

Design of the superconducting magnet for 9.4 Tesla whole-body magnetic resonance imaging

NASA Astrophysics Data System (ADS)

Li, Y.; Wang, Q.; Dai, Y.; Ni, Z.; Zhu, X.; Li, L.; Zhao, B.; Chen, S.

2017-02-01

A superconducting magnet for 9.4 Tesla whole-body magnetic resonance imaging is designed and fabricated in Institute of Electrical Engineering, Chinese Academy of Sciences. In this paper, the electromagnetic design methods of the main coils and compensating coils are presented. Sensitivity analysis is performed for all superconducting coils. The design of the superconducting shimming coils is also presented and the design of electromagnetic decoupling of the Z2 coils from the main coils is introduced. Stress and strain analysis with both averaged and detailed models is performed with finite element method. A quench simulation code with anisotropic continuum model and control volume method is developed by us and is verified by experimental study. By means of the quench simulation code, the quench protection system for the 9.4 T magnet is designed for the main coils, the compensating coils and the shimming coils. The magnet cryostat design with zero helium boiling-off technology is also introduced.

Four-channel surface coil array for sequential CW-EPR image acquisition

NASA Astrophysics Data System (ADS)

Enomoto, Ayano; Emoto, Miho; Fujii, Hirotada; Hirata, Hiroshi

2013-09-01

This article describes a four-channel surface coil array to increase the area of visualization for continuous-wave electron paramagnetic resonance (CW-EPR) imaging. A 776-MHz surface coil array was constructed with four independent surface coil resonators and three kinds of switches. Control circuits for switching the resonators were also built to sequentially perform EPR image acquisition for each resonator. The resonance frequencies of the resonators were shifted using PIN diode switches to decouple the inductively coupled coils. To investigate the area of visualization with the surface coil array, three-dimensional EPR imaging was performed using a glass cell phantom filled with a solution of nitroxyl radicals. The area of visualization obtained with the surface coil array was increased approximately 3.5-fold in comparison to that with a single surface coil resonator. Furthermore, to demonstrate the applicability of this surface coil array to animal imaging, three-dimensional EPR imaging was performed in a living mouse with an exogenously injected nitroxyl radical imaging agent.

A fourth gradient to overcome slice dependent phase effects of voxel-sized coils in planar arrays.

PubMed

Bosshard, John C; Eigenbrodt, Edwin P; McDougall, Mary P; Wright, Steven M

2010-01-01

The signals from an array of densely spaced long and narrow receive coils for MRI are complicated when the voxel size is of comparable dimension to the coil size. The RF coil causes a phase gradient across each voxel, which is dependent on the distance from the coil, resulting in a slice dependent shift of k-space. A fourth gradient coil has been implemented and used with the system's gradient set to create a gradient field which varies with slice. The gradients are pulsed together to impart a slice dependent phase gradient to compensate for the slice dependent phase due to the RF coils. However the non-linearity in the fourth gradient which creates the desired slice dependency also results in a through-slice phase ramp, which disturbs normal slice refocusing and leads to additional signal cancelation and reduced field of view. This paper discusses the benefits and limitations of using a fourth gradient coil to compensate for the phase due to RF coils.

Evidence-based pathology: umbilical cord coiling.

PubMed

Khong, T Y

2010-12-01

The generation of a pathology test result must be based on criteria that are proven to be acceptably reproducible and clinically relevant to be evidence-based. This review de-constructs the umbilical cord coiling index to illustrate how it can stray from being evidence-based. Publications related to umbilical cord coiling were retrieved and analysed with regard to how the umbilical coiling index was calculated, abnormal coiling was defined and reference ranges were constructed. Errors and other influences that can occur with the measurement of the length of the umbilical cord or of the number of coils can compromise the generation of the coiling index. Definitions of abnormal coiling are not consistent in the literature. Reference ranges defining hypocoiling or hypercoiling have not taken those potential errors or the possible effect of gestational age into account. Even the way numerical test results in anatomical pathology are generated, as illustrated by the umbilical coiling index, warrants a critical analysis into its evidence base to ensure that they are reproducible or free from errors.

Eddy current testing probe with dual half-cylindrical coils

NASA Astrophysics Data System (ADS)

Bae, Byung-Hoon; Choi, Jung-Mi; Kim, Soo-Yong

2000-02-01

We have developed a new eddy current probe composed of a dual half-cylindrical (2HC) coil as an exciting coil and a sensing coil that is placed in the small gap of the 2HC coil. The 2HC coil induces a linear eddy current on the narrow region within the target medium. The magnitude of eddy current has a maximum peak with the narrow width, underneath the center of the exciting 2HC coil. Because of the linear eddy current, the probe can be used to detect not only the existence of a crack but also its direction in conducting materials. Using specimen with a machined crack, and varying the exciting frequency from 0.5 to 100 kHz, we investigated the relationships between the direction of crack and the output voltage of the sensing coil.

Direct matching methods for coils and preamplifiers in MRI

NASA Astrophysics Data System (ADS)

Cao, Xueming; Fischer, Elmar; Hennig, Jürgen; Zaitsev, Maxim

2018-05-01

In this paper, direct matching methods for coils and preamplifiers in receiver arrays are presented. Instead of compensating the reactance of the input impedance of preamplifiers, in our method, the reactance was used to resonate with the coil matching networks and thus to decouple the coils. Furthermore, coil matching networks and preamplifier input matching networks were combined, meaning the coil loop can be matched to the transistor in the preamplifier directly. These matching methods and, for comparison, the conventional matching method were implemented with custom-made preamplifiers and coils. Decoupling and noise-matching performance were compared between these three configurations. Phase shifting networks between coils and preamplifiers are not necessary in our matching methods. With fewer components, these matching networks showed lower noise factors, while similar preamplifier-decoupling performance was found for all three methods.

Replacement of charged and polar residues in the coiled-coiled interface of huntingtin-interacting protein 1 (HIP1) causes aggregation and cell death.

PubMed

Fontaine, Sarah N; Bauer, Scott P; Lin, Xiaoyan; Poorfarahani, Sara; Ybe, Joel A

2012-09-21

HIP1 crystal structures solved in our laboratory revealed abnormalities in the coiled-coil region, suggesting intrinsic plasticity. To test this, specific amino acids in the coiled-coil were mutated. The apparent thermal stability of HIP1 was altered when Thr528 and Glu531 were replaced by leucine, and was enhanced when Lys510 was also mutated. In cells, HIP1 mutant expression produced aggregation. MTS and flow cytometry indicate a correlation between aggregated HIP1 and enhanced cell death. These data support the idea that flexibility of the HIP1 coiled-coil domain is important for normal function and may lead to new insights into Huntington's disease. Copyright © 2012 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

A Modified Alderman-Grant Coil makes possible an efficient cross-coil probe for high field solid-state NMR of lossy biological samples

NASA Astrophysics Data System (ADS)

Grant, Christopher V.; Yang, Yuan; Glibowicka, Mira; Wu, Chin H.; Park, Sang Ho; Deber, Charles M.; Opella, Stanley J.

2009-11-01

The design, construction, and performance of a cross-coil double-resonance probe for solid-state NMR experiments on lossy biological samples at high magnetic fields are described. The outer coil is a Modified Alderman-Grant Coil (MAGC) tuned to the 1H frequency. The inner coil consists of a multi-turn solenoid coil that produces a B 1 field orthogonal to that of the outer coil. This results in a compact nested cross-coil pair with the inner solenoid coil tuned to the low frequency detection channel. This design has several advantages over multiple-tuned solenoid coil probes, since RF heating from the 1H channel is substantially reduced, it can be tuned for samples with a wide range of dielectric constants, and the simplified circuit design and high inductance inner coil provides excellent sensitivity. The utility of this probe is demonstrated on two electrically lossy samples of membrane proteins in phospholipid bilayers (bicelles) that are particularly difficult for conventional NMR probes. The 72-residue polypeptide embedding the transmembrane helices 3 and 4 of the Cystic Fibrosis Transmembrane Conductance Regulator (CFTR) (residues 194-241) requires a high salt concentration in order to be successfully reconstituted in phospholipid bicelles. A second application is to paramagnetic relaxation enhancement applied to the membrane-bound form of Pf1 coat protein in phospholipid bicelles where the resistance to sample heating enables high duty cycle solid-state NMR experiments to be performed.

Design and use of a folded four-ring double-tuned birdcage coil for rat brain sodium imaging at 9.4 T.

PubMed

Ha, YongHyun; Choi, Chang-Hoon; Worthoff, Wieland A; Shymanskaya, Aliaksandra; Schöneck, Michael; Willuweit, Antje; Felder, Jörg; Shah, N Jon

2018-01-01

A folded four-ring quadrature birdcage coil was designed and constructed with a double-tune configuration of an outer high-pass coil for 1 H (400 MHz) and inner low-pass coil for 23 Na (105.72 MHz at 9.4 T). The coil was evaluated on the bench and in the scanner, comparing its performance with that of single-tuned coils and a large four-ring coil. All coils were tuned and matched and the isolation between two quadrature ports was found to be better than -13.7 dB for 1 H and -27 dB for 23 Na. Signal-to-noise ratios (SNRs) were calculated and 23 Na flip angle maps were acquired. 23 Na SNR of the folded four-ring reached ∼93% of that obtained with the single-tuned coil. A set of in vivo 1 H and 23 Na axial images to cover the whole rat brain were obtained. The performance of the folded four-ring coil and its benefit for 23 Na imaging experiments have been demonstrated. This proposed four-ring coil could avoid length restrictions, e.g. the shoulders, by folding the outer rings vertically. This facilitates the construction of double-tuned four-ring birdcage coils just to fit the head, leading to higher filling factors and better SNR. Copyright © 2017 Elsevier Inc. All rights reserved.

Construction and Test Results of Coils 2 and 3 of a 3-Nested-Coil 800-MHz REBCO Insert for the MIT 1.3-GHz LTS/HTS NMR Magnet.

PubMed

Park, Dongkeun; Bascuñán, Juan; Michael, Philip C; Lee, Jiho; Hahn, Seungyong; Iwasa, Yukikazu

2018-04-01

We present construction and test results of Coils 2 and 3 of a 3-coil 800-MHz REBCO insert (H800) for the MIT 1.3 GHz LTS/HTS NMR magnet currently under construction. Each of three H800 coils (Coils 1-3) is a stack of no-insulation REBCO double pancakes (DPs). The innermost 8.67-T Coil 1 (26 DPs) was completed in 2016; the middle 5.64-T Coil 2 (32 DPs) has been wound, assembled, and tested; and for the outermost 4.44-T Coil 3, its 38 DPs have been wound and preliminary tests were performed to characterize each DP at 77 K. Included for Coil 2 are: 1) 77-K data of critical current, index, and turn-to-turn characteristic resistivity of each DP; 2) stacking order of the 32 DPs optimized to maximize the Coil 2 current margin and minimize its Joule dissipation in the pancake-to-pancake joints; 3) procedure to experimentally determine and apply a room-temperature preload to the DP stack; 4) 77-K and 4.2-K test results after each of 64 pancakes was over-banded with 75-μm-thick stainless steel tape for a radial thickness of 5 mm. Presented for each DP in Coil 3 are 77-K dada of critical current, index, and turn-to-turn characteristic resistivity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malashkevich, Vladimir N.; Higgins, Chelsea D.; Almo, Steven C.

The coiled-coil is one of the most ubiquitous and well studied protein structural motifs. Significant effort has been devoted to dissecting subtle variations of the typical heptad repeat sequence pattern that can designate larger topological features such as relative α-helical orientation and oligomer size. Here in this paper we report the X-ray structure of a model coiled-coil peptide, HA2-Del-L2seM, which forms an unanticipated core antiparallel dimer with potential sites for discrete higher-order multimerization (trimer or tetramer). In the X-ray structure, a third, partially-ordered α-helix is weakly associated with the antiparallel dimer and analytical ultracentrifugation experiments indicate the peptide forms amore » well-defined tetramer in solution. The HA2-Del-L2seM sequence is closely related to a parent model peptide, HA2-Del, which we previously reported adopts a parallel trimer; HA2-Del-L2seM differs by only hydrophobic leucine to selenomethione mutations and thus this subtle difference is sufficient to switch both relative α-helical topology and number of α-helices participating in the coiled-coil. Comparison of the X-ray structures of HA2-Del-L2seM (reported here) with the HA2-Del parent (reported previously) reveals novel interactions involving the selenomethionine residues that promote antiparallel coiled-coil configuration and preclude parallel trimer formation. Finally, these novel atomic insights are instructive for understanding subtle features that can affect coiled-coil topology and provide additional information for design of antiparallel coiled-coils.« less

Manufacturing of REBCO coils strongly bonded to cooling members with epoxy resin aimed at its application to Maglev

NASA Astrophysics Data System (ADS)

Mizuno, Katsutoshi; Ogata, Masafumi; Hasegawa, Hitoshi

2014-11-01

The REBCO coated conductor has been attracted attention because of its high current density in the presence of high magnetic field. If the coated conductor is applied to Maglev, the operational temperature of the on-board magnets will be over 40 K and energy consumption of cryocoolers will be reduced. That high operational temperature also means the absence of liquid helium. Therefore, reliable thermal coupling is desirable for cooling the coils. We propose an epoxy impregnated REBCO coil co-wound with PTFE tape. While the PTFE tape prevents the performance degradation of the coil, the epoxy resin bonds the coil to cooling members. We carried out three experiments to confirm that the coil structure which we propose has robust thermal coupling without the degradation. First, thermal resistances of paraffin and epoxy were measured varying the temperature from room temperature to 10 K. The measurement result indicates that paraffin has a risk of losing thermal coupling during cooling down. In another experiment, PTFE (polytetrafluoroethylene) tape insulator prevented performance degradation of a small epoxy impregnated REBCO coil, while another REBCO coil with polyimide tape showed clear performance degradation. Finally, we produced a racetrack REBCO coil with the same outer dimension as a Maglev on-board magnet coil. Although the racetrack coil was installed in a GFRP coil case and tightly bonded to the case by epoxy impregnation, any performance degradation was not observed.

Design and optimization of resonance-based efficient wireless power delivery systems for biomedical implants.

PubMed

Ramrakhyani, A K; Mirabbasi, S; Mu Chiao

2011-02-01

Resonance-based wireless power delivery is an efficient technique to transfer power over a relatively long distance. This technique typically uses four coils as opposed to two coils used in conventional inductive links. In the four-coil system, the adverse effects of a low coupling coefficient between primary and secondary coils are compensated by using high-quality (Q) factor coils, and the efficiency of the system is improved. Unlike its two-coil counterpart, the efficiency profile of the power transfer is not a monotonically decreasing function of the operating distance and is less sensitive to changes in the distance between the primary and secondary coils. A four-coil energy transfer system can be optimized to provide maximum efficiency at a given operating distance. We have analyzed the four-coil energy transfer systems and outlined the effect of design parameters on power-transfer efficiency. Design steps to obtain the efficient power-transfer system are presented and a design example is provided. A proof-of-concept prototype system is implemented and confirms the validity of the proposed analysis and design techniques. In the prototype system, for a power-link frequency of 700 kHz and a coil distance range of 10 to 20 mm, using a 22-mm diameter implantable coil resonance-based system shows a power-transfer efficiency of more than 80% with an enhanced operating range compared to ~40% efficiency achieved by a conventional two-coil system.

Two new planar coil designs for a high pressure radio frequency plasma source

NASA Astrophysics Data System (ADS)

Munsat, T.; Hooke, W. M.; Bozeman, S. P.; Washburn, S.

1995-04-01

Two planar coil designs for a high pressure rf plasma source are investigated using spectroscopic techniques and circuit analysis. In an Ar plasma a truncated version of the commonly used ``spiral'' coil is found to produce improvements in peak electron density of 20% over the full version. A coil with figure-8 geometry is found to move plasma inhomogeneities off of center and produce electron densities comparable to the spiral coils. Both of these characteristics are advantageous in industrial applications. Coil design characteristics for favorable power coupling are also determined, including the necessity of closed hydrodynamic plasma loops and the drawback of closely situated antiparallel coil currents.

Superconducting magnetic coil

DOEpatents

Aized, Dawood; Schwall, Robert E.

1999-06-22

A superconducting magnetic coil includes a plurality of sections positioned axially along the longitudinal axis of the coil, each section being formed of an anisotropic high temperature superconductor material wound about a longitudinal axis of the coil and having an associated critical current value that is dependent on the orientation of the magnetic field of the coil. The cross section of the superconductor, or the type of superconductor material, at sections along the axial and radial axes of the coil are changed to provide an increased critical current at those regions where the magnetic field is oriented more perpendicularly to the conductor plane, to thereby increase the critical current at these regions and to maintain an overall higher critical current of the coil.

Superconducting magnetic coil

DOEpatents

Aized, Dawood; Schwall, Robert E.

1996-06-11

A superconducting magnetic coil includes a plurality of sections positioned axially along the longitudinal axis of the coil, each section being formed of an anisotropic high temperature superconductor material wound about a longitudinal axis of the coil and having an associated critical current value that is dependent on the orientation of the magnetic field of the coil. The cross section of the superconductor, or the type of superconductor material, at sections along the axial and radial axes of the coil are changed to provide an increased critical current at those regions where the magnetic field is oriented more perpendicularly to the conductor plane, to thereby increase the critical current at these regions and to maintain an overall higher critical current of the coil.

Cross-axis synchronous flow-through coil planet centrifuge for large-scale preparative counter-current chromatography. III. Performance of large-bore coils in slow planetary motion.

PubMed

Ito, Y; Zhang, T Y

1988-11-25

A preparative capability of the present cross-axis synchronous flow-through coil planet centrifuge was demonstrated with 0.5 cm I.D. multilayer coils. Results of the model studies with short coils indicated that the optimal separations are obtained at low revolutional speeds of 100-200 rpm in both central and lateral coil positions. Preparative separations were successfully performed on 2.5-10 g quantities of test samples in a pair of multilayer coils connected in series with a total capacity of 2.5 l. The sample loading capacity will be scaled up in several folds by increasing the column width.

49 CFR 393.120 - What are the rules for securing metal coils?

Code of Federal Regulations, 2011 CFR

2011-10-01

....100 through 393.114. (b) Securement of coils transported with eyes vertical on a flatbed vehicle, in a...), across the eye of the coil, to the right side of the vehicle or intermodal container (near the rearmost... intermodal container (near the forwardmost part of the coil), across the eye of the coil, to the left side of...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andreas, Michael P.; Ajay, Gautam; Gellings, Jaclyn A.

X-ray structural determination of segments of the myosin rod has proved difficult because of the strong salt-dependent aggregation properties and repeating pattern of charges on the surface of the coiled-coil that lead to the formation of paracrystals. This problem has been resolved in part through the use of globular assembly domains that improve protein folding and prevent aggregation. The primary consideration now in designing coiled-coil fusion constructs for myosin is deciding where to truncate the coiled-coil and which amino acid residues to include from the folding domain. This is especially important for myosin that contains numerous regions of low predictedmore » coiled-coil propensity. Here we describe the strategy adopted to determine the structure of the region that extends from Arg1677 – Leu1797 that included two areas that do not show a strong sequence signature of a conventional left-handed coiled coil or canonical heptad repeat. This demonstrates again that, with careful choice of fusion constructs, overlapping structures exhibit very similar conformations for the myosin rod fragments in the canonical regions. However, conformational variability is seen around Leu1706 which is a hot spot for cardiomyopathy mutations suggesting that this might be important for function.« less

Modified van Vaals-Bergman coaxial cable coil (lambda coil) for high-field imaging.

PubMed

Matsuzawa, H; Nakada, T

1996-03-01

An easily constructed, low-capacitive coupling volume coil based on the van Vaals-Bergman coaxial cable coil for high field imaging is described. The coil (designated "lambda coil") was constructed using two 5/4 length 50 omega coaxial cables matched to a 50 omega transmission line with LC bridge balun. The standing wave on the single 5/4 lambda length coaxial cable provides two points of current maxima in oppositional direction. Therefore, the four current elements necessary for effective B1 field generation can be obtained by two 5/4 lambda length coaxial cables arranged analogous to 1/2 lambda T-antenna. Capacitive coupling between the coil elements and conductive samples (i.e. animals) is minimized by simply retaining the shield of the coaxial cable for the area of voltage maxima. The lambda coil exhibited excellent performance as a volume coil with a high quality factor and highly homogeneous rf fields. Because of its dramatically simple architecture and excellent performance, the lambda coil configuration appears to be an economical alternative to the original van Vaals-Bergman design, especially for research facilities with a high field magnet and limited bore space.

Robust peptide bundles designed computationally

NASA Astrophysics Data System (ADS)

Haider, Michael; Zhang, Huixi Violet; Kiick, Kristi; Saven, Jeffery; Pochan, Darrin

Peptides are ideal candidates for the design and controlled assembly of nanoscale materials due to their potential to assemble with atomistic precision as in biological systems. Unlike other work utilizing natural proteins and structural motifs, this effort is completely de novo in order to build arbitrary structures with desired size for the specific placement and separation of functional groups. We have successfully computationally designed soluble, coiled coil, peptide, tetramer bundles which are robust and stable. Using circular dichroism we demonstrated the thermal stability of these bundles as well as confirmed their alpha helical and coiled coil nature. The stability of these bundles arises from the computational design of the coiled coil interior core residues. The coiled coil tetramer was confirmed to be the dominant species by analytical ultra-centrifugation sedimentation studies. We also established how these bundles behave in solution using small angle neutron scattering. The form factor of the bundles is well represented by a cylinder model and their behavior at high concentrations is modeled using a structure factor for aggregates of the cylinders. All of these experiments support our claim that the designed coiled coil bundles were achieved in solution. NSF DMREF 1234161.

Human LINE-1 retrotransposition requires a metastable coiled coil and a positively charged N-terminus in L1ORF1p

PubMed Central

Khazina, Elena

2018-01-01

LINE-1 (L1) is an autonomous retrotransposon, which acted throughout mammalian evolution and keeps contributing to human genotypic diversity, genetic disease and cancer. L1 encodes two essential proteins: L1ORF1p, a unique RNA-binding protein, and L1ORF2p, an endonuclease and reverse transcriptase. L1ORF1p contains an essential, but rapidly evolving N-terminal portion, homo-trimerizes via a coiled coil and packages L1RNA into large assemblies. Here, we determined crystal structures of the entire coiled coil domain of human L1ORF1p. We show that retrotransposition requires a non-ideal and metastable coiled coil structure, and a strongly basic L1ORF1p amino terminus. Human L1ORF1p therefore emerges as a highly calibrated molecular machine, sensitive to mutation but functional in different hosts. Our analysis rationalizes the locally rapid L1ORF1p sequence evolution and reveals striking mechanistic parallels to coiled coil-containing membrane fusion proteins. It also suggests how trimeric L1ORF1p could form larger meshworks and indicates critical novel steps in L1 retrotransposition. PMID:29565245

Development of a REBCO HTS magnet for Maglev - repeated bending tests of HTS pancake coils -

NASA Astrophysics Data System (ADS)

Sugino, Motohikoa; Mizuno, Katsutoshi; Tanaka, Minoru; Ogata, Masafumi

2018-01-01

In the past study, two manufacturing methods were developed that can manufacture pancake coils by using REBCO coated conductors. It was confirmed that the conductors have no electric degradation that caused by the manufacturing method. The durability evaluation tests of the pancake coils were conducted as the final evaluation of the coil manufacturing method in this study. The repeated bending deformation was applied to manufactured pancake coils in the tests. As the results of these tests, it was confirmed that the pancake coils that were manufactured by two methods had the durability for the repeated bending deformation and the coils maintained the appropriate mechanical performance and electric performance. We adopted the fusion bonding method as the coil manufacturing method of the HTS magnet Furthermore, using the prototype pancake coil that was manufactured by the fusion bonding method as a test sample, the repeated bending test under the exited condition was conducted. Thus it was confirmed that the coil manufactured by the fusion bonding method has no degradation of the electricity performance and the mechanical properties even if the repeated bending deformation was applied under the exited condition.

Simulation of chain of quenches on toroidal HTS-SMES taking account of thermal and electromagnetic characteristics

NASA Astrophysics Data System (ADS)

Oga, Y.; Noguchi, S.; Igarashi, H.

When a temperature rise occurs at a local area inside a coil of toroidal HTS-SMES by any reason, a temperature hotspot which results in a thermal runaway appears at the local area. Subsequently, after appearing the local normal zone in the HTS coil, the transport current of the HTS coil decrease since the resistance of HTS coil appears and the current partially flows into a parallel-connecting shunt resistance. However, if the transport current of the normal-transitioned HTS coil is hardly changed, the temperature on the hotspot would rise more and then the normal zone would spread rapidly. It may cause a serious accident due to high stored energy. Therefore, using the numerical simulation, we have investigated the behaviors of the coil current, the critical current, and the temperature in the superconducting element coils of HTS-SMES. Consequently, the temperature of the superconducting element coils rises up extremely when a large heat is generated at a certain area of one of them by any reason. Moreover, there is a possibility that the shunt resister hardly functions for protection since the coil is burned out due to high inductances and low resistance of the superconducting element coil.

Construction and Operation of an Internal Coil Device, RT-1, with a High-Temperature Superconductor

NASA Astrophysics Data System (ADS)

Ogawa, Yuichi; Yoshida, Zensho; Morikawa, Junji; Saito, Haruhiko; Watanabe, Sho; Yano, Yoshihisa; Mizumaki, Shoichi; Tosaka, Taizo

An internal coil device called Ring Trap-1 (RT-1) has been constructed to explore an innovative concept for a high-beta plasma based on a new relaxation theory. A high-temperature superconductor (HTS) Bi-2223 tape is employed for the internal coil of RT-1. The coil is cooled to 20 K with helium gas supplied by G-M refrigerators, and charged to a magnetomotive force of 250 kA using an external power supply. For these cooling and charging methods, we have developed several innovative techniques such as a demountable transfer tube system, persistent current switch, detachable electrode, and others. In addition, we have paid much attention to the deterioration of the HTS tape during the fabrication of the internal coil. As a result, we have demonstrated that the decay of the persistent current of the internal coil is ˜1% during 8 h. The internal coil is lifted with a levitation coil located at the upper region of the vacuum vessel. The coil position monitored with laser sensors is feedback controlled through the regulation of the levitation coil current. Stable levitation for a few hours has been demonstrated for various plasma experiments.

Plasma Experiments on an Internal Coil Device with an High Temperature Superconductor

NASA Astrophysics Data System (ADS)

Yuichi, Ogawa; Junji, Morikawa; Kotaro, Ohkuni; Dan, Hori; Shigeo, Yamakosi; Nagato, Yanagi; Toshiyuki, Mito; Masataka, Iwakuma; Toshio, Uede

2003-10-01

An internal coil device would be expected for exploring high beta plasmas based on plasma relaxation process. Prof. A. Hasegawa proposed an advanced fusion reactor with a dipole configuration, and Mahajan and Yoshida developed a new high beta state based on two-fluid relaxation theory. To study these high beta plasmas, we have constructed an internal coil device with a high temperature superconductor. The major radius of the internal coil is 15 cm, and the coil current is 50 kA. Three different types of Ag-sheathed Bi-2223 tapes are employed; i.e., a high critical current tape with a low silver ratio for the main HTS coil, a 0.3wt3atprovided by a GM refrigerator and supplied to the coil through a check valve, and the coil current is directly excited with the external power supply through removable electrodes. It took about 11 hours to cool the coil down to 21 K from the room temperature, and the nominal cable current of 118 A (overall coil current: 50 kA) has been achieved. A decay time constant of the persistent current is a few tens of hours. Plasma experiments in a dipole configuration have been initiated.

Magnetic lumbosacral motor root stimulation with a flat, large round coil.

PubMed

Matsumoto, Hideyuki; Octaviana, Fitri; Hanajima, Ritsuko; Terao, Yasuo; Yugeta, Akihiro; Hamada, Masashi; Inomata-Terada, Satomi; Nakatani-Enomoto, Setsu; Tsuji, Shoji; Ugawa, Yoshikazu

2009-04-01

The aim of this paper is to develop a reliable method for supramaximal magnetic spinal motor root stimulation (MRS) for lower limb muscles using a specially devised coil. For this study, 42 healthy subjects were recruited. A 20-cm diameter coil designated as a Magnetic Augmented Translumbosacral Stimulation (MATS) coil was used. Compound muscle action potentials (CMAPs) were recorded from the abductor hallucis muscle. Their CMAPs were compared with those obtained by MRS using a conventional round or double coil and with those obtained using high-voltage electrical stimulation. The MATS coil evoked CMAPs to supramaximal stimulation in 80 of 84 muscles, although round and double coils elicited supramaximal CMAPs in only 15 and 18 of 84 muscles, respectively. The CMAP size to the MATS coil stimulation was the same as that to high-voltage electrical motor root stimulation. MATS coil achieved supramaximal stimulation of the lumbosacral spinal nerves. The CMAPs to supramaximal stimulation are necessary for measurement of the amplitude and area for the detection of conduction blocks. The MATS coil stimulation of lumbosacral motor roots is a reliable method for measuring the CMAP size from lower limb muscles in spinal motor root stimulation.

Testing of machine wound second generation HTS tape Vacuum Pressure Impregnated coils

NASA Astrophysics Data System (ADS)

Swaffield, D.; Lewis, C.; Eugene, J.; Ingles, M.; Peach, D.

2014-05-01

Delamination of second generation (2G) High Temperature Superconducting (HTS) tapes has previously been reported when using resin based insulation systems for wound coils. One proposed root cause is the differential thermal contraction between the coil former and the resin encapsulated coil turns resulting in the tape c-axis tensile stress being exceeded. Importantly, delamination results in unacceptable degradation of the superconductor critical current level. To mitigate the delamination risk and prove winding, jointing and Vacuum Pressure Impregnation (VPI) processes in the production of coils for superconducting rotating machines at GE Power Conversion two scaled trial coils have been wound and extensively tested. The coils are wound from 12mm wide 2G HTS tape supplied by AMSC onto stainless steel 'racetrack' coil formers. The coils are wound in two layers which include both in-line and layer-layer joints subject to in-process test. The resin insulation system chosen is VPI and oven cured. Tests included; insulation resistance, repeat quench and recovery of the superconductor, heat runs and measurement of n-value, before and after multiple thermal cycling between ambient and 35 Kelvin. No degradation of coil performance is evidenced.

Synthesis, characterisation and applications of coiled carbon nanotubes.

PubMed

Hanus, Monica J; Harris, Andrew T

2010-04-01

Coiled carbon nanotubes are helical carbon structures formed when heptagonal and pentagonal rings are inserted into the hexagonal backbone of a 'straight' nanotube. Coiled carbon nanotubes have been reported with both regular and irregular helical structures. In this work the structure, growth mechanism(s), synthesis, properties and potential applications of coiled carbon nanotubes are reviewed. Published data suggests that coiled carbon nanotube synthesis occurs due to nonuniform extrusion of carbon from a catalyst surface. To date, coiled carbon nanotubes have been synthesised using catalyst modification techniques including: (i) the addition of S or P containing compounds during synthesis; (ii) the use of binary or ternary metal catalysts; (iii) the use of microwaves to create a local temperature gradient around individual catalyst particles and; (iv) the use of pH control during catalyst preparation. In most instances coiled carbon nanotubes are produced as a by-product; high yield and/or large-scale synthesis of coiled carbon nanotubes remains problematic. The qualitative analysis of coiled carbon nanotubes is currently hindered by the absence of specific characterisation data in the literature, e.g., oxidation profiles measured by thermogravimetric analysis and Raman spectra of pure coiled carbon nanotube samples.

Coil Compression for Accelerated Imaging with Cartesian Sampling

PubMed Central

Zhang, Tao; Pauly, John M.; Vasanawala, Shreyas S.; Lustig, Michael

2012-01-01

MRI using receiver arrays with many coil elements can provide high signal-to-noise ratio and increase parallel imaging acceleration. At the same time, the growing number of elements results in larger datasets and more computation in the reconstruction. This is of particular concern in 3D acquisitions and in iterative reconstructions. Coil compression algorithms are effective in mitigating this problem by compressing data from many channels into fewer virtual coils. In Cartesian sampling there often are fully sampled k-space dimensions. In this work, a new coil compression technique for Cartesian sampling is presented that exploits the spatially varying coil sensitivities in these non-subsampled dimensions for better compression and computation reduction. Instead of directly compressing in k-space, coil compression is performed separately for each spatial location along the fully-sampled directions, followed by an additional alignment process that guarantees the smoothness of the virtual coil sensitivities. This important step provides compatibility with autocalibrating parallel imaging techniques. Its performance is not susceptible to artifacts caused by a tight imaging fieldof-view. High quality compression of in-vivo 3D data from a 32 channel pediatric coil into 6 virtual coils is demonstrated. PMID:22488589