Initiating the Validation of CCIM Processability for Multi-phase all Ceramic (SYNROC) HLW Form: Plan for Test BFY14CCIM-C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maio, Vince

This plan covers test BFY14CCIM-C which will be a first–of–its-kind demonstration for the complete non-radioactive surrogate production of multi-phase ceramic (SYNROC) High Level Waste Forms (HLW) using Cold Crucible Induction Melting (CCIM) Technology. The test will occur in the Idaho National Laboratory’s (INL) CCIM Pilot Plant and is tentatively scheduled for the week of September 15, 2014. The purpose of the test is to begin collecting qualitative data for validating the ceramic HLW form processability advantages using CCIM technology- as opposed to existing ceramic–lined Joule Heated Melters (JHM) currently producing BSG HLW forms. The major objectives of BFY14CCIM-C are tomore » complete crystalline melt initiation with a new joule-heated resistive starter ring, sustain inductive melting at temperatures between 1600 to 1700°C for two different relatively high conductive materials representative of the SYNROC ceramic formation inclusive of a HLW surrogate, complete melter tapping and pouring of molten ceramic material in to a preheated 4 inch graphite canister and a similar canister at room temperature. Other goals include assessing the performance of a new crucible specially designed to accommodate the tapping and pouring of pure crystalline forms in contrast to less recalcitrant amorphous glass, assessing the overall operational effectiveness of melt initiation using a resistive starter ring with a dedicated power source, and observing the tapped molten flow and subsequent relatively quick crystallization behavior in pans with areas identical to standard HLW disposal canisters. Surrogate waste compositions with ceramic SYNROC forming additives and their measured properties for inductive melting, testing parameters, pre-test conditions and modifications, data collection requirements, and sampling/post-demonstration analysis requirements for the produced forms are provided and defined.« less

Determination of heat conductivity of waste glass feed and its applicability for modeling the batch-to-glass conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hujova, Miroslava; Pokorny, Richard; Klouzek, Jaroslav

The heat conductivity of reacting melter feed affects the heat transfer and conversion process in the cold cap (the reacting feed floating on molten glass). To investigate it, we simulated the feed conditions and morphology in the cold-cap by preparing “fast-dried slurry blocks”, formed by rapidly evaporating water from feed slurry poured onto a 200°C surface. A heat conductivity meter was used to measure heat conductivity of samples cut from the fast-dried slurry blocks, samples of a cold cap retrieved from a laboratory-scale melter, and loose dry powder feed samples. Our study indicates that the heat conductivity of the feedmore » in the cold cap is significantly higher than that of loose dry powder feed, resulting from the feed solidification during the water evaporation from the feed slurry. To assess the heat transfer at higher temperatures when feed turns into foam, we developed a theoretical model that predicts the foam heat conductivity based on morphology data from in-situ X-ray computed tomography. The implications for the mathematical modeling of the cold cap are discussed.« less

The effect of mechanical stress on electric resistance of nanographite-epoxy composites

NASA Astrophysics Data System (ADS)

Vovchenko, L.; Lazarenko, A.; Matzui, L.; Zhuravkov, A.

2012-03-01

The in-plane electric resistance Ra of composite materials (CMs) thermoexfoliated graphite(TEG)-epoxy resin(ED) under compression along compacting C-axis has been investigated by four-probe method. TEG content was 5-75 wt%. It was shown that specimens prepared by cold pressing are denser and reveal lower values of electric resistivity in comparison with specimens prepared by pouring. It was found that compression of the specimens leads to plastic deformation of specimens (εpl) and essential irreversible decrease of electric resistance during the first cycle of loading (up to 50 MPa), especially for the poured specimens with low density. Within the proposed model the contact resistance Rk between graphite particles in CM has been evaluated and it was shown that it increased with the decrease in TEG content in CM and depends on compacting method of CMs and the dispersity of graphite filler.

Advanced Soldier Thermoelectric Power System for Power Generation from Battlefield Heat Sources

DTIC Science & Technology

2010-09-01

Figure 6.10 TE Module with Microtherm Added Around & Between Legs ............................................................... 57  Figure 6.11 Short... Microtherm ® insulation, 2.6 (W) of heater power was required to maintain a temperature of 400 ºC. This is an indication of the losses in the system...side of the module to the cold plate.  Pour in Microtherm to insulate the module.  Make sure to clean all insulation from the hot side electrodes

Aerothermodynamics and Propulsion Integration for Hypersonic Vehicles (L’Integration de la Propusion et de l’aerodynnamique pour les vehicules hypersoniques).

DTIC Science & Technology

1996-10-01

aerothermoelasticity, temperature gradients and internal heat gies, belong fully resuable SSTO and TSTO sytems, protection. The demand of extreme light...supersonic conditions, convergent and convergent-divergent nozzles matching the cold cage internal diameter will be fixed on the end plate. A set of five...in hypersonic flow. AIAA Paper93- des Fluides, Avril 1996. 5111, 5th International Aerospace Planes and 16. Morrisette, E.L., Creel, T.R., Chen, F.J

Survival at Sea for Mariners, Aviators and Search and Rescue Personnel (Survie en mer pour les marins, les aviateurs et le personnel de recherche et de sauvetage)

DTIC Science & Technology

2008-02-01

think that death from sinking in cold water is a thing of the past – the Titanic, the Empress of Ireland, the Lusitania , etc. Nothing could be further...Luftwaffe, 9B-3 Lusitania , 9C-5 M Macintosh, R.R., 9B-3 Mae West, 9B-3 Mallison’s Seamen’s Friend and Bather’s Companion, 9B-2 Manikin, 9C-10

Identification des parametres du moteur de l'avion Cessna Citation X pour la phase de croisiere a partir des tests en vol et a base des reseaux de neurones =

NASA Astrophysics Data System (ADS)

Zaag, Mahdi

La disponibilite des modeles precis des avions est parmi les elements cles permettant d'assurer leurs ameliorations. Ces modeles servent a ameliorer les commandes de vol et de concevoir de nouveaux systemes aerodynamiques pour la conception des ailes deformables des avions. Ce projet consiste a concevoir un systeme d'identification de certains parametres du modele du moteur de l'avion d'affaires americain Cessna Citation X pour la phase de croisiere a partir des essais en vol. Ces essais ont ete effectues sur le simulateur de vol concu et fabrique par CAE Inc. qui possede le niveau D de la dynamique de vol. En effet, le niveau D est le plus haut niveau de precision donne par l'autorite federale de reglementation FAA de l'aviation civile aux Etats-Unis. Une methodologie basee sur les reseaux de neurones optimises a l'aide d'un algorithme intitule le "grand deluge etendu" est utilisee dans la conception de ce systeme d'identification. Plusieurs tests de vol pour differentes altitudes et differents nombres de Mach ont ete realises afin de s'en servir comme bases de donnees pour l'apprentissage des reseaux de neurones. La validation de ce modele a ete realisee a l'aide des donnees du simulateur. Malgre la nonlinearite et la complexite du systeme, les parametres du moteur ont ete tres bien predits pour une enveloppe de vol determinee. Ce modele estime pourrait etre utilise pour des analyses de fonctionnement du moteur et pourrait assurer le controle de l'avion pendant cette phase de croisiere. L'identification des parametres du moteur pourrait etre realisee aussi pour les autres phases de montee et de descente afin d'obtenir son modele complet pour toute l'enveloppe du vol de l'avion Cessna Citation X (montee, croisiere, descente). Cette methode employee dans ce travail pourrait aussi etre efficace pour realiser un modele pour l'identification des coefficients aerodynamiques du meme avion a partir toujours des essais en vol. None None None

Validation of hot-poured crack sealant performance-based guidelines.

DOT National Transportation Integrated Search

2017-06-01

This report summarizes a comprehensive research effort to validate thresholds for performance-based guidelines and : grading system for hot-poured asphalt crack sealants. A series of performance tests were established in earlier research and : includ...

Analyse experimentale des performances d'une batterie au lithium pour l'aeronautique

NASA Astrophysics Data System (ADS)

Bonnin, Romain

Ce memoire a pour objectif d'identifier et d'etudier les performances necessaires pour qu'une batterie au lithium puisse etre utilisee dans le secteur de l'aeronautique. C'est pourquoi dans le cadre de notre recherche, nous allons proposer une procedure de tests permettant d'analyser et de determiner si la batterie au lithium peut etre implantee dans un avion. En vue de repondre a l'analyse des performances, une etude des fonctionnalites demandees par l'avion ainsi que des normes preexistantes vont etre effectuees. Suite a cette etape, nous allons elaborer un banc d'essais. Une fois le banc d'essais acheve, nous allons tester une batterie au lithium qui est supposee disposer de toutes les caracteristiques techniques requises pour etre implantee dans un avion. Ces tests nous permettront donc d'emettre un avis sur l'utilisation des batteries au lithium dans le domaine de l'aeronautique.

Surface Detail Reproduction and Dimensional Stability of Contemporary Irreversible Hydrocolloid Alternatives after Immediate and Delayed Pouring.

PubMed

Kusugal, Preethi; Chourasiya, Ritu Sunil; Ruttonji, Zarir; Astagi, Preeti; Nayak, Ajay Kumar; Patil, Abhishekha

2018-01-01

To overcome the poor dimensional stability of irreversible hydrocolloids, alternative materials were introduced. The dimensional changes of these alternatives after delayed pouring are not well studied and documented in the literature. The purpose of the study is to evaluate and compare the surface detail reproduction and dimensional stability of two irreversible hydrocolloid alternatives with an extended-pour irreversible hydrocolloid at different time intervals. All testing were performed according to the ANSI/ADA specification number 18 for surface detail reproduction and specification number 19 for dimensional change. The test materials used in this study were newer irreversible hydrocolloid alternatives such as AlgiNot FS, Algin-X Ultra FS, and Kromopan 100 which is an extended pour irreversible hydrocolloid as control. The surface detail reproduction was evaluated using stereomicroscope. The dimensional change after storage period of 1 h, 24 h, and 120 h was assessed and compared between the test materials and control. The data were analyzed using one-way ANOVA and post hoc Bonferroni test. Statistically significant results ( P < 0.001) were seen when mean scores of the tested materials were compared with respect to reproduction of 22 μm line from the metal block. Kromopan 100 showed statistically significant differences between different time intervals ( P < 0.001) and exhibited more dimensional change. Algin-X Ultra FS proved to be more accurate and dimensionally stable. Newer irreversible hydrocolloid alternative impression materials were more accurate in surface detail reproduction and exhibited minimal dimensional change after storage period of 1 h, 24 h, and 120 h than extended-pour irreversible hydrocolloid impression material.

ROLE OF MANGANESE REDUCTION/OXIDATION (REDOX) ON FOAMING AND MELT RATE IN HIGH LEVEL WASTE (HLW) MELTERS (U)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C; Michael Stone, M

2007-03-30

High-level nuclear waste is being immobilized at the Savannah River Site (SRS) by vitrification into borosilicate glass at the Defense Waste Processing Facility (DWPF). Control of the Reduction/Oxidation (REDOX) equilibrium in the DWPF melter is critical for processing high level liquid wastes. Foaming, cold cap roll-overs, and off-gas surges all have an impact on pouring and melt rate during processing of high-level waste (HLW) glass. All of these phenomena can impact waste throughput and attainment in Joule heated melters such as the DWPF. These phenomena are caused by gas-glass disequilibrium when components in the melter feeds convert to glass andmore » liberate gases such as H{sub 2}O vapor (steam), CO{sub 2}, O{sub 2}, H{sub 2}, NO{sub x}, and/or N{sub 2}. During the feed-to-glass conversion in the DWPF melter, multiple types of reactions occur in the cold cap and in the melt pool that release gaseous products. The various gaseous products can cause foaming at the melt pool surface. Foaming should be avoided as much as possible because an insulative layer of foam on the melt surface retards heat transfer to the cold cap and results in low melt rates. Uncontrolled foaming can also result in a blockage of critical melter or melter off-gas components. Foaming can also increase the potential for melter pressure surges, which would then make it difficult to maintain a constant pressure differential between the DWPF melter and the pour spout. Pressure surges can cause erratic pour streams and possible pluggage of the bellows as well. For these reasons, the DWPF uses a REDOX strategy and controls the melt REDOX between 0.09 {le} Fe{sup 2+}/{summation}Fe {le} 0.33. Controlling the DWPF melter at an equilibrium of Fe{sup +2}/{summation}Fe {le} 0.33 prevents metallic and sulfide rich species from forming nodules that can accumulate on the floor of the melter. Control of foaming, due to deoxygenation of manganic species, is achieved by converting oxidized MnO{sub 2} or Mn{sub 2}O{sub 3} species to MnO during melter preprocessing. At the lower redox limit of Fe{sup +2}/{summation}Fe {approx} 0.09 about 99% of the Mn{sup +4}/Mn{sup +3} is converted to Mn{sup +2}. Therefore, the lower REDOX limits eliminates melter foaming from deoxygenation.« less

[Occupational dermatitis in construction and public workers].

PubMed

Frimat, Paul

2002-09-01

Construction workers perform a large variety of duties concerned with building, repairing, and wrecking buildings, bridges, dams, roads, railways and so on. The work may include mixing, pouring and spreading concrete, asphalt, gravel and other materials. Despite the increasing mechanization of construction and the more frequent use of precast concrete sections, contact with wet cement still occurs, particularly in small jobs. The work is hard physical labor, often under difficult conditions, including hot, cold, and wet weather. Occupational diseases of the skin in the construction have paralleled industrial development.

Surface Detail Reproduction and Dimensional Stability of Contemporary Irreversible Hydrocolloid Alternatives after Immediate and Delayed Pouring

PubMed Central

Kusugal, Preethi; Chourasiya, Ritu Sunil; Ruttonji, Zarir; Astagi, Preeti; Nayak, Ajay Kumar; Patil, Abhishekha

2018-01-01

Purpose: To overcome the poor dimensional stability of irreversible hydrocolloids, alternative materials were introduced. The dimensional changes of these alternatives after delayed pouring are not well studied and documented in the literature. The purpose of the study is to evaluate and compare the surface detail reproduction and dimensional stability of two irreversible hydrocolloid alternatives with an extended-pour irreversible hydrocolloid at different time intervals. Materials and Methods: All testing were performed according to the ANSI/ADA specification number 18 for surface detail reproduction and specification number 19 for dimensional change. The test materials used in this study were newer irreversible hydrocolloid alternatives such as AlgiNot FS, Algin-X Ultra FS, and Kromopan 100 which is an extended pour irreversible hydrocolloid as control. The surface detail reproduction was evaluated using stereomicroscope. The dimensional change after storage period of 1 h, 24 h, and 120 h was assessed and compared between the test materials and control. The data were analyzed using one-way ANOVA and post hoc Bonferroni test. Results: Statistically significant results (P < 0.001) were seen when mean scores of the tested materials were compared with respect to reproduction of 22 μm line from the metal block. Kromopan 100 showed statistically significant differences between different time intervals (P < 0.001) and exhibited more dimensional change. Algin-X Ultra FS proved to be more accurate and dimensionally stable. Conclusions: Newer irreversible hydrocolloid alternative impression materials were more accurate in surface detail reproduction and exhibited minimal dimensional change after storage period of 1 h, 24 h, and 120 h than extended-pour irreversible hydrocolloid impression material. PMID:29599578

Influence of polymethyl acrylate additive on the formation of particulate matter and NOX emission of a biodiesel-diesel-fueled engine.

PubMed

Monirul, Islam Mohammad; Masjuki, Haji Hassan; Kalam, Mohammad Abdul; Zulkifli, Nurin Wahidah Mohd; Shancita, Islam

2017-08-01

The aim of this study is to investigate the effect of the polymethyl acrylate (PMA) additive on the formation of particulate matter (PM) and nitrogen oxide (NO X ) emission from a diesel coconut and/or Calophyllum inophyllum biodiesel-fueled engine. The physicochemical properties of 20% of coconut and/or C. inophyllum biodiesel-diesel blend (B20), 0.03 wt% of PMA with B20 (B20P), and diesel fuel were measured and compared to ASTM D6751, D7467, and EN 14214 standard. The test results showed that the addition of PMA additive with B20 significantly improves the cold-flow properties such as pour point (PP), cloud point (CP), and cold filter plugging point (CFPP). The addition of PMA additives reduced the engine's brake-specific energy consumption of all tested fuels. Engine emission results showed that the additive-added fuel reduce PM concentration than B20 and diesel, whereas the PM size and NO X emission both increased than B20 fuel and baseline diesel fuel. Also, the effect of adding PMA into B20 reduced Carbon (C), Aluminum (Al), Potassium (K), and volatile materials in the soot, whereas it increased Oxygen (O), Fluorine (F), Zinc (Zn), Barium (Ba), Chlorine (Cl), Sodium (Na), and fixed carbon. The scanning electron microscope (SEM) results for B20P showed the lower agglomeration than B20 and diesel fuel. Therefore, B20P fuel can be used as an alternative to diesel fuel in diesel engines to lower the harmful emissions without compromising the fuel quality.

Effects of annealing on microstructure, composition and magnetic properties of rolled Fe/Ga-Al composite strip

NASA Astrophysics Data System (ADS)

Zheng, Yanwen; Zhang, Zhihao; Jiang, Yanbin

2018-04-01

The Ga liquid and Al powder were mechanically mixed and poured into a hollow iron plate, after alloying, the composite plate was rolled at room temperature for preparing an Fe/Ga-Al composite strip. The effect of annealing conditions on the diffusion, microstructures and magnetostrictive properties of the strip were studied. The composite plate had good cold rolling formability. After annealing at 750-850 °C for 5 h of the cold-rolled sample with a reduction of 97%, the diffusion distance of Ga and Al in the Fe matrix increased with an increase of the annealing temperature. However, some holes appeared in the center of the sample annealed at a temperature of more than 830 °C, which was detrimental to the subsequent rolling. The combination of the secondary cold rolling and annealing was beneficial to improve the composition homogeneity and magnetic properties of the sample. The magnetostriction coefficient (λ//) of the primary rolled sample was low, ∼4 × 10-6. After annealing and secondary cold rolling, the λ// of the sample increased to 9 × 10-6 and the λ// of the sample conducted by further annealing at 820 °C for 20 h reached 27.5 × 10-6.

Effect of storage time of extended-pour and conventional alginate impressions on dimensional accuracy of casts.

PubMed

Rohanian, Ahmad; Ommati Shabestari, Ghasem; Zeighami, Somayeh; Samadi, Mohammad Javad; Shamshiri, Ahmad Reza

2014-11-01

Some manufacturers claim to have produced new irreversible hydro-colloids that are able to maintain their dimensional stability during storage. The present study evaluated the effect of storage time on dimensional stability of three alginates: Hydrogum 5, Tropicalgin and Alginoplast. In this experimental in-vitro trial, a total of 90 alginate impressions were made from a Dentoform model using Hydrogum 5, Tropicalgin and Alginoplast alginates. The impressions were stored in a sealed plastic bag without a damp paper towel for 0, 24, 48, 72 and 120 hours and then poured with type III dental stone. Cross-arch (facial of 6 to facial of 6 on the opposite side) and antero-posterior (distal of right first molar to the ipsilateral central incisor) measurements were made with a digital caliper on the casts. Data were analyzed by two-way and one-way ANOVA and Tukey's post-hoc test (P<0.05). Alginate type and the pouring time significantly affected the dimensional stability of alginate impressions (both Ps<0.001). Pouring of Hydrogum 5 impressions can be delayed for up to 120 hours without significant dimensional changes. Alginoplast impressions may be poured after 72 hours, but Tropicalgin should be poured immediately and the storage time should not be more than 24 hours. Immediate pouring of alginate impressions provides the highest accuracy in reproducing the teeth and adjacent tissues; however, this study demonstrated that pouring may be delayed for up to five days using extended-pour (Hydrogum 5) alginates.

Effect of Storage Time of Extended-Pour and Conventional Alginate Impressions on Dimensional Accuracy of Casts

PubMed Central

Rohanian, Ahmad; Ommati Shabestari, Ghasem; Zeighami, Somayeh; Samadi, Mohammad Javad; Shamshiri, Ahmad Reza

2014-01-01

Objectives: Some manufacturers claim to have produced new irreversible hydro-colloids that are able to maintain their dimensional stability during storage. The present study evaluated the effect of storage time on dimensional stability of three alginates: Hydrogum 5, Tropicalgin and Alginoplast. Materials and Methods: In this experimental in-vitro trial, a total of 90 alginate impressions were made from a Dentoform model using Hydrogum 5, Tropicalgin and Alginoplast alginates. The impressions were stored in a sealed plastic bag without a damp paper towel for 0, 24, 48, 72 and 120 hours and then poured with type III dental stone. Cross-arch (facial of 6 to facial of 6 on the opposite side) and antero-posterior (distal of right first molar to the ipsilateral central incisor) measurements were made with a digital caliper on the casts. Data were analyzed by two-way and one-way ANOVA and Tukey’s post-hoc test (P<0.05). Results: Alginate type and the pouring time significantly affected the dimensional stability of alginate impressions (both Ps<0.001). Pouring of Hydrogum 5 impressions can be delayed for up to 120 hours without significant dimensional changes. Alginoplast impressions may be poured after 72 hours, but Tropicalgin should be poured immediately and the storage time should not be more than 24 hours. Conclusion: Immediate pouring of alginate impressions provides the highest accuracy in reproducing the teeth and adjacent tissues; however, this study demonstrated that pouring may be delayed for up to five days using extended-pour (Hydrogum 5) alginates. PMID:25628695

Systems Concepts for Integrated Air Defense of Multinational Mobile Crisis Reaction Forces (Concepts de systemes pour la defense aerienne integree de forces internationales mobiles d’intervention en situation de crise)

DTIC Science & Technology

2001-03-01

characteristics shown in Table 1 are based upon a conventional armoured formation, and implicitly at divisional level or above, they could also apply at lower...widely dispersed Ease of Physical big/hot mid-size/cool small/cold targeting Camouflage scrimmed draped visual full/thermal EMCON 4 3 2 1 Visibility...line of sight occulting/obscured non line of sight Contact static FLOT fluid confused melée Armour soft semi-hard hard defensive aids Protection

An In-Depth Analysis of the Cold Boot Attack: Can It Be Used for Sound Forensic Memory Acquisition?

DTIC Science & Technology

2011-01-01

technique, les auteurs font ressortir ses avantages et inconvénients, son applicabilité et sa pertinence pour l’acquisition du contenu de la mémoire...Les auteurs croient qu’une compréhension approfondie de ce phénomène habilitera les enquêteurs en informatique judiciaire à en tirer profit lorsque...individu. Comme l’équipe de Princeton n’a pas spécifiquement examiné l’applicabilité de leur technique à l’informatique judiciaire, les auteurs de la

A new portable vibrator for plaster pouring: effect on the marginal fit at cylinder-abutment

PubMed Central

de ANDRADE, Pâmela Cândida Aires Ribas; LUTHI, Leonardo Flores; STANLEY, Kyle; CARDOSO, Antônio Carlos

2012-01-01

Objective The aim of this study was to test a new portable vibrator for plaster pouring (developed for this purpose), comparing the effect of its use on the accuracy of working cast of implant-supported restorations to the conventional vibrator. Material and methods From a master cast with 2 implants, 30 transfer moldings were made randomly and divided into three groups: Group I (GI): pouring performed in an outsourced dental laboratory with conventional plaster vibrator (10 casts), Group II (GII): pouring performed in the laboratory of the Federal University of Santa Catarina (UFSC) with conventional plaster vibrator (10 casts) and Group III (GIII): pouring performed with the portable vibrator fabricated for this study (10 casts). The position of the analogue and marginal adaptation of the infrastructure were verified by testing the single screw on the master model and on the working model. The measurement of misfit was blindly performed with a precision microscope and analyzing unit, Quadra-Check 200. The data were statistically analyzed by analysis of variance (ANOVA) and the Holm-Sidak test (α=0.05). Results Means±standard deviations were as follows: GI: 19.19±4.73 µm; GII: 21.72±5.41 µm; GIII: 13.5±2.39 µm (P<0.05), with GIII significantly lower as compared to the other groups. Conclusion Within the limitations of this study, it was concluded that a greater accuracy of working cast was achieved when a portable vibrator was used for casting molds. PMID:23138736

Methodologies nouvelles pour la realisation d'essais dans la soufflerie Price-Paidoussis

NASA Astrophysics Data System (ADS)

Flores Salinas, Manuel

Le present memoire en genie de la production automatisee vise a decrire le travail effectue dans la soufflerie Price-Paidoussis du laboratoire LARCASE pour trouver les methodologies experimentales et les procedures de tests, qui seront utilisees avec les modeles d'ailes actuellement au laboratoire. Les methodologies et procedures presentees ici vont permettre de preparer les tests en soufflerie du projet MDO-505 Architectures et technologies deformables pour l'amelioration des performances des ailes, qui se derouleront durant l'annee 2015. D'abord, un bref historique des souffleries subsoniques sera fait. Les differentes sections de la soufflerie Price-Paidoussis seront decrites en mettant l'emphase sur leur influence dans la qualite de l'ecoulement qui se retrouve dans la chambre d'essai. Ensuite, une introduction a la pression, a sa mesure lors de tests en soufflerie et les instruments utilises pour les tests en soufflerie au laboratoire LARCASE sera presente, en particulier le capteur piezoelectrique XCQ-062. Une attention particuliere sera portee au mode de fonctionnement, a son installation, a la mesure et a la detection des frequences et aux sources d'erreurs lorsqu'on utilise des capteurs de haute precision comme la serie XCQ-062 du fournisseur Kulite. Finalement, les procedures et les methodologies elaborees pour les tests dans la soufflerie Price-Paidoussis seront utilisees sur quatre types d'ailes differentes. L'article New methodology for wind tunnel calibration using neural networks - EGD approch portant sur une nouvelle facon de predire les caracteristiques de l'ecoulement a l'interieur de la soufflerie Price-Paidoussis se trouve dans l'annexe 2 de ce document. Cet article porte sur la creation d'un reseau de neurones multicouche et sur l'entrainement des neurones, Ensuite, une comparaison des resultats du reseau de neurones a ete fait avec des valeurs simules avec le logiciel Fluent.

Medication for Military Aircrew: Current Use, Issues, and Strategies for Expanded Options (les medicaments pour les equipaes militaires: Consommation actuelle, questions et strategies pour des options elargies)

DTIC Science & Technology

2001-06-01

HMG-CoA reductase inhibitors, commonly referred to as “statins” (lovastatin, pravastatin, simvastatin, fluvastatin, atorvastatin ) d. Others (nicotinic...cholesterol by 2 - 15%. Many statins (pravastatin, atorvastatin , fluvastatin, lovastatin, and simvastatin) have been developed for clinical use and are now...trail making test, or visual memory test.16 There are unpublished data about atorvastatin and pravastatin, in which both showed an increase in

Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter. Preliminary settling and resuspension testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.; Fowley, M. D.; Miller, D. H.

2016-05-01

The full-scale, room-temperature Hanford Tank Waste Treatment and Immobilization Plant (WTP) High-Level Waste (HLW) melter riser test system was successfully operated with silicone oil and magnetite particles at a loading of 0.1 vol %. Design and construction of the system and instrumentation, and the selection and preparation of simulant materials, are briefly reviewed. Three experiments were completed. A prototypic pour rate was maintained, based on the volumetric flow rate. Settling and accumulation of magnetite particles were observed at the bottom of the riser and along the bottom of the throat after each experiment. The height of the accumulated layer atmore » the bottom of the riser, after the first pouring experiment, approximated the expected level given the solids loading of 0.1 vol %. More detailed observations of particle resuspension and settling were made during and after the third pouring experiment. The accumulated layer of particles at the bottom of the riser appeared to be unaffected after a pouring cycle of approximately 15 minutes at the prototypic flow rate. The accumulated layer of particles along the bottom of the throat was somewhat reduced after the same pouring cycle. Review of the time-lapse recording showed that some of the settling particles flow from the riser into the throat. This may result in a thicker than expected settled layer in the throat.« less

Performance du GeneXpert MTB/RIF® dans le diagnostic de la tuberculose extra-pulmonaire à Dakar: 2010-2015

PubMed Central

Diallo, Awa Ba; Kollo, Abdoulkader Issifi; Camara, Makhtar; Lo, Seynabou; Ossoga, Gedeon Walbang; Mbow, Moustapha; Karam, Farba; Niang, Mame Yacine Fall; Thiam, Aliou; Diawara, Awa Ndiaye; Mboup, Souleymane; Diallo, Aissatou Gaye

2016-01-01

Introduction Le défi des pays en voie de développement est la disponibilité de méthodes de diagnostic rapide et précis pour le management de la tuberculose. Des techniques moléculaires offrent cet avantage et nous avons utilisé le test GeneXpert MTB/RIF dans le diagnostic de la tuberculose extra-pulmonaire pour évaluer sa performance par rapport aux méthodes conventionnelles. Méthodes Entre 2010 et 2015, 544 échantillons cliniques extra-pulmonaires ont été recueillis et traitées par la microscopie, la culture et le GeneXpert. L'étude de la sensibilité aux antituberculeux a été effectué avec le MGIT 960. Le Génotype MTBDRplus a été utilisé pour confirmer les cas de résistance à la rifampicine détectés par le système GX. Résultats La population d'étude de 544 patients incluait 55,15% d'hommes et 44,85% de femmes. L'âge des patients variait entre 1 à 92 avec la majorité dans le groupe d'âge 18-45 ans. La sensibilité et la spécificité globale de la microscopie étaient de 43,86% et 98,36%, et pour le GeneXpert® 94,74% et 97,95% respectivement avec 95% IC. Deux résultats de résistance à la rifampicine discordants ont été trouvées entre le test GeneXpert et la méthode phénotypique. Les résultats du test MTBDRplus ont montré une concordance de 100% avec ceux du MGIT 960 pour les cas discordants de résistance à la rifampicine. Conclusion Cette étude a montré que le test GeneXpert a une plus grande sensibilité pour le diagnostic de routine de la tuberculose extra-pulmonaire et devrait être utilisé à la place de la microscopie. Les cas de résistance à la rifampicine détectés par le GeneXpert doivent être confirmés par d'autres tests moléculaires avant d'initier un traitement. PMID:28292091

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rabin, S.A.; Martin, M.M.; Lotts, A.L.

The fabricability of dispersion fuels using UO/sub 2/ or UC as the dispersoid and uranium combined with 10 to 15 wt% Mo as the matrix was investigated. Cores containing l7.8 wt% UO/sub 2/ dispersed in U-- 15 wt.% Mo were successfully fabricated to about 80% of theoretical density by cold pressing at 50 tsi, sintering at 1100 deg C, and cold coining at 50 tsi. Comparable results were obtained with UC as the dispersoid. Core fabrication results varied greatly with the type of matrix powder used. Occluded gases, pour density, and surface cleanliness bore important relations to the fabrication behaviormore » of powders. Suitable pressing and sintering results were obtained with prealloyed, calcium-reduced U--Mo powder and with molybdenum and calcium-reduced uranium as elemental powders. Shotted prealloyed powders were difficult to press and sinter, as were elemental and prealloyed powders prepared by hydriding. The cores containing UO/sub 2/ were picture-frame, hot-roll-clad as miniature plates. Molybdenum, Fansteel 82, and Zr--3 wt% Al were investigated as cladding materials. While each bonded well to itself, only the molybdenum-clad core, rolled at 1150 deg C to 10/1 reduction, resulted in dispersions free of ruptures and UO/sub 2/ fragmentation and in strong bonding to the core, evaluated by metallography, mechanical peel, and thermal shock tests. The matrix phase was homogeneous, but the UO/sub 2/ dispersoid showed stringering characteristic of cores worked by hot rolling. Core densities as high as 99% of theoretical were obtained. (auth)« less

Spiral Salmonella assay: validation against the standard pour-plate assay.

PubMed

Diehl, M; Fort, F

1996-01-01

The spiral Ames assay, an automated approach to bacterial mutagenicity testing which simplifies the test procedure and reduces the amount of drug required to generate mutagenic dose-response information, has been evaluated and validated for routine screening. The spiral plater delivers the Salmonella bacteria, exogenous metabolic activation system and drug to the surface of a rotating agar plate one on top of another in such a way that a uniform density of bacteria is exposed to a logarithmically decreasing volume of drug. Following an incubation of 48 hr at 37 degrees C, the plates are scanned by a laser counter, and the data are subjected to a computerized analysis. Petri plates of 15 cm diameter were used to provide a concentration range of about 250-fold per plate. The Salmonella were concentrated 20-fold to increase sensitivity. Thirty-eight compounds from a variety of chemical classes, including both pharmaceuticals and known mutagens of moderate to strong potency, were tested in both the spiral and the standard pour-plate assays. There was overall test agreement on positive or negative results for 82% of the compounds tested. When only the results from strains TA98 plus TA100 were considered, the agreement was 87%. When positive results were obtained, the fold increase over vehicle control was on average twice as great for the spiral assay compared to the pour-plate assay. It was concluded that the two assay procedures generally provided comparable results, with the spiral assay being somewhat more sensitive in terms of dose-response than the pour-plate assay.

Preliminary Common Module Design Handbook.

DTIC Science & Technology

1976-04-02

oat* circuit« it • canttant currant tourca <Q’’ With «a rosso « current «rive. V threuah 05 era turna* off thus thuttine *e*n the...ply» heat input renf’*9 fro» toro *h -r IS •mute« aa«iau» to 77* Kelvin »tertiea to 0 * «Ott at cold fieaer taaeeretwre of...trie «c»l»t ond OOjuOt for • toro Ml Ccr«ful|y pour llowitf nitrooon HU into tho d»t»ctor/o«M»r «wdu’-p I to». Con- tlnwa

Synthesis and evaluation of C-ether formulations for use as high temperature lubricants and hydraulic fluids

NASA Technical Reports Server (NTRS)

Clark, F. S.; Green, R. L.; Miller, D. R.

1974-01-01

The formulation and evaluation of C-ether fluids for use in the hydraulic and lubrication systems of the space shuttle and advanced air breathing engines were studied to lower the pour point of a reference C-ether from -29 C to -40 C without changing its evaporation loss. Use of disiloxanes mixed with C-ethers gave a -40 C pour point fluid with little change in the desired evaporation loss or in oxidative stability. A second -40 C pour point fluid containing only C-ethers was also developed. A screening program tested lubrication additives for C-ethers and the new fluids. Six additive packages were chosen for evaluation in 316 C bearing tests, two for evaluation in 260 C pump tests. The goal of the bearing test was a 100 hour run. The rig was a specially designed 80-mm axially loaded ball bearing. The C-ether base fluid ran only one hour at 316 C before cage wear failure occurred. The best additive blends ran 47, 94 and 100 hours. The 96 hour test gave excessive deposits. The 100 hour test had no wear failures; an unexplained loss of cage silver occurred from areas of direct fluid impingement on the cage.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abboud, Alexander; Guillen, Donna Post; Pokorny, Richard

At the Hanford site in the state of Washington, more than 56 million gallons of radioactive waste is stored in underground tanks. The cleanup plan for this waste is vitrification at the Waste Treatment Plant (WTP), currently under construction. At the WTP, the waste will be blended with glass-forming materials and heated to 1423K, then poured into stainless steel canisters to cool and solidify. A fundamental understanding of the glass batch melting process is needed to optimize the process to reduce cost and decrease the life cycle of the cleanup effort. The cold cap layer that floats on the surfacemore » of the glass melt is the primary reaction zone for the feed-to-glass conversion. The conversion reactions include water release, melting of salts, evolution of batch gases, dissolution of quartz and the formation of molten glass. Obtaining efficient heat transfer to this region is crucial to achieving high rates of glass conversion. Computational fluid dynamics (CFD) modeling is being used to understand the heat transfer dynamics of the system and provide insight to optimize the process. A CFD model was developed to simulate the DM1200, a pilot-scale melter that has been extensively tested by the Vitreous State Laboratory (VSL). Electrodes are built into the melter to provide Joule heating to the molten glass. To promote heat transfer from the molten glass into the reactive cold cap layer, bubbling of the molten glass is used to stimulate forced convection within the melt pool. A three-phase volume of fluid approach is utilized to model the system, wherein the molten glass and cold cap regions are modeled as separate liquid phases, and the bubbling gas and plenum regions are modeled as one lumped gas phase. The modeling of the entire system with a volume of fluid model allows for the prescription of physical properties on a per-phase basis. The molten glass phase and the gas phase physical properties are obtained from previous experimental work. Finding representative properties for the cold cap region is more difficult, as this region is not a true liquid, but rather a multilayer region consisting of a porous and a foamy layer. Physical properties affecting heat transfer, namely the thermal conductivity and heat capacity, have been fit to closely match data and observations from laboratory experiments. Data from xray tomography and quenching of laboratory-scale cold caps provide insight into the topology of bubble distribution within the cold cap at various temperatures. Heat transfer within the melter was validated by comparison with VSL data for the pilot-scale melter.« less

"This war for men's minds": the birth of a human science in Cold War America.

PubMed

Martin-Nielsen, Janet

2010-01-01

The past decade has seen an explosion of work on the history of the human sciences during the Cold War. This work, however, does not engage with one of the leading human sciences of the period: linguistics. This article begins to rectify this knowledge gap by investigating the influence of linguistics and its concept of study, language, on American public, political and intellectual life during the postwar and early Cold War years. I show that language emerged in three frameworks in this period: language as tool, language as weapon, and language as knowledge. As America stepped onto the international stage, language and linguistics were at the forefront: the military poured millions of dollars into machine translation, American diplomats were required to master scores of foreign languages, and schoolchildren were exposed to language-learning on a scale never before seen in the United States. Together, I argue, language and linguistics formed a critical part of the rise of American leadership in the new world order - one that provided communities as dispersed as the military, the diplomatic corps, scientists and language teachers with a powerful way of tackling the problems they faced. To date, linguistics has not been integrated into the broader framework of Cold War human sciences. In this article, I aim to bring both language, as concept, and linguistics, as discipline, into this framework. In doing so, I pave the way for future work on the history of linguistics as a human science.

Field Trial Data Analysis and Testing (FiTAT) Tool

DTIC Science & Technology

2011-10-01

amplitude/phase pour chaque antenne du réseau) contenu dans les données acquises pourrait être faite par FiTAT et utilisé dans PAASoM pour déterminer...identity matrix, k is the loop gain, φ is the correlation matrix of the incident signals and T = [1 0 . . . 0]T . The length of vector T is equal to the

1. VIEW NORTHEAST, LEFT TO RIGHT COLD CALIBRATION TEST STAND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW NORTHEAST, LEFT TO RIGHT COLD CALIBRATION TEST STAND COLD CALIBRATION BLOCKHOUSE IN FOREGROUND. - Marshall Space Flight Center, East Test Area, Cold Calibration Test Stand, Huntsville, Madison County, AL

Active Acoustics using Bellhop-DRDC: Run Time Tests and Suggested Configurations for a Tracking Exercise in Shallow Scotian Waters

DTIC Science & Technology

2005-05-01

simulée d’essai pour obtenir les diagrammes de perte de transmission et de réverbération pour 18 éléments (une source, un réseau remorqué et 16 bouées...were recorded using a 1.5GHz Pentium 4 processor. The test results indicate that the Bellhop program runs fast enough to provide the required acoustic...was determined that the Bellhop program will be fast enough for these clients. Future Plans It is intended to integrate further enhancements that

Impact of International Decisions of TAI Generation

DTIC Science & Technology

1996-12-01

in their specified fields as advisers on scientific and technical matters. Among them, the Coma6 Comultakifpow h D6jinition & la Seeondo (CCDS) deak...Time (UTC). For issues concerning time, the CIPM takes advice from the ComitC Consultatif pour la DCfinition de la Seconde (CCDS). Although the name...tests of new devices and suggestions to manufacturers. CONCLUSIONS The meetings of the Comite Consultatif pour la DCfinition de la Seconde gather

ELIMINATION OF THE CHARACTERIZATION OF DWPF POUR STREAM SAMPLE AND THE GLASS FABRICATION AND TESTING OF THE DWPF SLUDGE BATCH QUALIFICATION SAMPLE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amoroso, J.; Peeler, D.; Edwards, T.

2012-05-11

A recommendation to eliminate all characterization of pour stream glass samples and the glass fabrication and Product Consistency Test (PCT) of the sludge batch qualification sample was made by a Six-Sigma team chartered to eliminate non-value-added activities for the Defense Waste Processing Facility (DWPF) sludge batch qualification program and is documented in the report SS-PIP-2006-00030. That recommendation was supported through a technical data review by the Savannah River National Laboratory (SRNL) and is documented in the memorandums SRNL-PSE-2007-00079 and SRNL-PSE-2007-00080. At the time of writing those memorandums, the DWPF was processing sludge-only waste but, has since transitioned to a coupledmore » operation (sludge and salt). The SRNL was recently tasked to perform a similar data review relevant to coupled operations and re-evaluate the previous recommendations. This report evaluates the validity of eliminating the characterization of pour stream glass samples and the glass fabrication and Product Consistency Test (PCT) of the sludge batch qualification samples based on sludge-only and coupled operations. The pour stream sample has confirmed the DWPF's ability to produce an acceptable waste form from Slurry Mix Evaporator (SME) blending and product composition/durability predictions for the previous sixteen years but, ultimately the pour stream analysis has added minimal value to the DWPF's waste qualification strategy. Similarly, the information gained from the glass fabrication and PCT of the sludge batch qualification sample was determined to add minimal value to the waste qualification strategy since that sample is routinely not representative of the waste composition ultimately processed at the DWPF due to blending and salt processing considerations. Moreover, the qualification process has repeatedly confirmed minimal differences in glass behavior from actual radioactive waste to glasses fabricated from simulants or batch chemicals. In contrast, the variability study has significantly added value to the DWPF's qualification strategy. The variability study has evolved to become the primary aspect of the DWPF's compliance strategy as it has been shown to be versatile and capable of adapting to the DWPF's various and diverse waste streams and blending strategies. The variability study, which aims to ensure durability requirements and the PCT and chemical composition correlations are valid for the compositional region to be processed at the DWPF, must continue to be performed. Due to the importance of the variability study and its place in the DWPF's qualification strategy, it will also be discussed in this report. An analysis of historical data and Production Records indicated that the recommendation of the Six Sigma team to eliminate all characterization of pour stream glass samples and the glass fabrication and PCT performed with the qualification glass does not compromise the DWPF's current compliance plan. Furthermore, the DWPF should continue to produce an acceptable waste form following the remaining elements of the Glass Product Control Program; regardless of a sludge-only or coupled operations strategy. If the DWPF does decide to eliminate the characterization of pour stream samples, pour stream samples should continue to be collected for archival reasons, which would allow testing to be performed should any issues arise or new repository test methods be developed.« less

Formulation, caracterisation, modelisation et prevision du comportement thermomecanique des pieces plastiques et composites de fibres de bois : Application aux engrenages =

NASA Astrophysics Data System (ADS)

Mijiyawa, Faycal

Cette etude permet d'adapter des materiaux composites thermoplastiques a fibres de bois aux engrenages, de fabriquer de nouvelles generations d'engrenages et de predire le comportement thermique de ces engrenages. Apres une large revue de la litterature sur les materiaux thermoplastiques (polyethylene et polypropylene) renforces par les fibres de bois (bouleau et tremble), sur la formulation et l'etude du comportement thermomecanique des engrenages en plastique-composite; une relation a ete etablie avec notre presente these de doctorat. En effet, beaucoup d'etudes sur la formulation et la caracterisation des materiaux composites a fibres de bois ont ete deja realisees, mais aucune ne s'est interessee a la fabrication des engrenages. Les differentes techniques de formulation tirees de la litterature ont facilite l'obtention d'un materiau composite ayant presque les memes proprietes que les materiaux plastiques (nylon, acetal...) utilises dans la conception des engrenages. La formulation des materiaux thermoplastiques renforces par les fibres de bois a ete effectuee au Centre de recherche en materiaux lignocellulosiques (CRML) de l'Universite du Quebec a Trois-Rivieres (UQTR), en collaboration avec le departement de Genie Mecanique, en melangeant les composites avec deux rouleaux sur une machine de type Thermotron-C.W. Brabender (modele T-303, Allemand) ; puis des pieces ont ete fabriquees par thermocompression. Les thermoplastiques utilises dans le cadre de cette these sont le polypropylene (PP) et le polyethylene haute densite (HDPE), avec comme renfort des fibres de bouleau et de tremble. A cause de l'incompatibilite entre la fibre de bois et le thermoplastique, un traitement chimique a l'aide d'un agent de couplage a ete realise pour augmenter les proprietes mecaniques des materiaux composites. Pour les composites polypropylene/bois : (1) Les modules elastiques et les contraintes a la rupture en traction des composites PP/bouleau et PP/tremble evoluent lineairement en fonction du taux de fibres, avec ou sans agent de couplage (Maleate de polypropylene MAPP). De plus, l'adherence entre les fibres de bois et le plastique est amelioree en utilisant seulement 3 % MAPP, entrainant donc une augmentation de la contrainte maximale bien qu'aucun effet significatif ne soit observe sur le module d'elasticite. (2) Les resultats obtenus montrent que, en general, les proprietes en traction des composites polypropylene/bouleau, polypropylene/tremble et polypropylene/bouleau/ tremble sont tres semblables. Les composites plastique-bois (WPCs), en particulier ceux contenant 30 % et 40 % de fibres, ont des modules elastiques plus eleves que certains plastiques utilises dans l'application des engrenages (ex. Nylon). Pour les composites polyethylene/bois, avec 3%Maleate de polyethylene (MAPE): (1) Tests de traction : le module elastique passe de 1.34 GPa a 4.19 GPa pour le composite HDPE/bouleau, alors qu'il passe de 1.34 GPa a 3.86 GPa pour le composite HDPE/tremble. La contrainte maximale passe de 22 MPa a 42.65 MPa pour le composite HDPE/bouleau, alors qu'elle passe de 22 MPa a 43.48 MPa pour le composite HDPE/tremble. (2) Tests de flexion : le module elastique passe de 1.04 GPa a 3.47 GPa pour le composite HDPE/bouleau et a 3.64 GPa pour le composite HDPE/tremble. La contrainte maximale passe de 23.90 MPa a 66.70 MPa pour le composite HDPE/bouleau, alors qu'elle passe a 59.51 MPa pour le composite HDPE/tremble. (3) Le coefficient de Poisson determine par impulsion acoustique est autour de 0.35 pour tous les composites HDPE/bois. (4) Le test de degradation thermique TGA nous revele que les materiaux composites presentent une stabilite thermique intermediaire entre les fibres de bois et la matrice HDPE. (5) Le test de mouillabilite (angle de contact) revele que l'ajout de fibres de bois ne diminue pas de facon significative les angles de contact avec de l'eau parce que les fibres de bois (bouleau ou tremble) semblent etre enveloppees par la matrice sur la surface des composites, comme le montrent des images prises au microscope electronique a balayage MEB. (6) Le modele de Lavengoof-Goettler predit mieux le module elastique du composite thermoplastique/bois. (7) Le HDPE renforce par 40 % de bouleau est mieux adapte pour la fabrication des engrenages, car le retrait est moins important lors du refroidissement au moulage. La simulation numerique semble mieux predire la temperature d'equilibre a la vitesse de 500 tr/min; alors qu'a 1000 tr/min, on remarque une divergence du modele. (Abstract shortened by ProQuest.). None None None None None None None None

Self-disinfecting Alginate vs Conventional Alginate: Effect on Surface Hardness of Gypsum Cast-An in vitro Study.

PubMed

Madhavan, Ranjith; George, Navia; Thummala, Niharika R; Ravi, S V; Nagpal, Ajay

2017-11-01

For the construction of any dental prosthesis, accurate impressions are necessary. Hence, we undertook the present study to evaluate and compare the surface hardness of gypsum casts poured from impressions made using conventional alginate and self-disinfecting alginate. A total of 30 impressions of stainless steel die were made, out of which 15 impressions were made with conventional alginate and 15 were made with self-disinfecting alginate and poured using Type III dental stone. Thirty stone specimens were subjected for hardness testing. Data were analyzed using independent samples t-test to compare the mean surface hardness. Difference in surface hardness was statistically insignificant (p > 0.05). Surface hardness of gypsum casts poured using impressions made from self-disinfecting alginate and conventional alginates were comparable. Self-disinfecting alginates may be employed in clinical practice as safe and effective materials to overcome the infection control issues without compromising on the properties of the material.

The Ocean`s Thermohaline Circulation in a Fish Tank

NASA Astrophysics Data System (ADS)

Lavender, K.; Joyce, P.; Graziano, L.; Harris, S.; Jaroslow, G.; Lea, C.; Schell, J.; Witting, J.

2005-12-01

This demonstration develops intuition about density stratification, a concept critical to understanding the ocean`s thermohaline circulation. In addition, students learn how temperature and salinity affect density, how these characteristics may be density-compensating, and students gain practice in graphing and interpreting vertical profiles and temperature-salinity (T-S) diagrams. The demonstration requires a rectangular fish tank (5-10 gallons) with a plexiglass partition, preparation of three colored ''water masses'' representing surface water (warm and fresh), ''mystery'' Mediterranean Water (warm and salty), and North Atlantic Deep Water (NADW; cold and salty), a kitchen sponge, and a temperature and salinity probe. Density may be computed using an Equation of State calculator (e.g. online version at http://fermi.jhuapl.edu/denscalc.html). The larger side of the fish tank is filled halfway with NADW, then surface water is layered on top by carefully pouring it on a floating sponge. A student volunteer measures the temperature and salinity of the two water masses, while another computes the densities. Students draw vertical profiles and T-S diagrams representing the temperature, salinity, and density of the water column. The properties of the ''mystery'' water are measured and students predict what will happen when the water is poured on the opposite side of the partition and is allowed to overflow into the layered water. If the density gradients are sufficiently large, a beautiful internal wave develops as the mystery water overflows the sill and becomes intermediate Mediterranean Water. If time permits, having a student blow on the surface illustrates the limited influence of ''wind'' with depth; an internal wave may by forced by depressing the thermocline with a large, flat spoon; and pouring extra NADW on the sponge floating at the surface may illustrate deep convection.

40 CFR 86.213-11 - Fuel specifications.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.213-11 Fuel specifications. (a) Gasoline... the text in this section follows: Table—Cold CO Fuel Specifications Item ASTM test Cold CO low octane.... Diesel test fuel used for cold temperature FTP testing under part 600 of this chapter must be a winter...

40 CFR 86.213-11 - Fuel specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.213-11 Fuel specifications. (a) Gasoline... the text in this section follows: Table—Cold CO Fuel Specifications Item ASTM test Cold CO low octane.... Diesel test fuel used for cold temperature FTP testing under part 600 of this chapter must be a winter...

40 CFR 86.213-11 - Fuel specifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.213-11 Fuel specifications. (a) Gasoline... the text in this section follows: Table—Cold CO Fuel Specifications Item ASTM test Cold CO low octane.... Diesel test fuel used for cold temperature FTP testing under part 600 of this chapter must be a winter...

40 CFR 86.213-11 - Fuel specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.213-11 Fuel specifications. (a) Gasoline... the text in this section follows: Table—Cold CO Fuel Specifications Item ASTM test Cold CO low octane.... Diesel test fuel used for cold temperature FTP testing under part 600 of this chapter must be a winter...

Extended spectrum SWIR camera with user-accessible Dewar

NASA Astrophysics Data System (ADS)

Benapfl, Brendan; Miller, John Lester; Vemuri, Hari; Grein, Christoph; Sivananthan, Siva

2017-02-01

Episensors has developed a series of extended short wavelength infrared (eSWIR) cameras based on high-Cd concentration Hg1-xCdxTe absorbers. The cameras have a bandpass extending to 3 microns cutoff wavelength, opening new applications relative to traditional InGaAs-based cameras. Applications and uses are discussed and examples given. A liquid nitrogen pour-filled version was initially developed. This was followed by a compact Stirling-cooled version with detectors operating at 200 K. Each camera has unique sensitivity and performance characteristics. The cameras' size, weight and power specifications are presented along with images captured with band pass filters and eSWIR sources to demonstrate spectral response beyond 1.7 microns. The soft seal Dewars of the cameras are designed for accessibility, and can be opened and modified in a standard laboratory environment. This modular approach allows user flexibility for swapping internal components such as cold filters and cold stops. The core electronics of the Stirlingcooled camera are based on a single commercial field programmable gate array (FPGA) that also performs on-board non-uniformity corrections, bad pixel replacement, and directly drives any standard HDMI display.

Validation de la version française du Questionnaire de Bournemouth

PubMed Central

Martel, Johanne; Dugas, Claude; Lafond, D.; Descarreaux, M.

2009-01-01

Les auto questionnaires font partie intégrante de l’évaluation des patients ayant des douleurs cervicales. Le Questionnaire de Bournemouth intègre la réalité biopsychosociale dans l’évaluation des douleurs cervicales et sa version anglais (QBc-a) est validée et présente des propriétés psychométriques de modérées à excellentes. L’objectif de cette étude est de traduire et valider une version française de ce questionnaire. La traduction et l’adaptation a été complétée en utilisant la méthode de traduction contre-traduction qui a permis d’obtenir un consensus entre les deux versions. L’étude de validation impliquait 68 sujets (âge moyen 41 ans) qui participaient à un essai clinique randomisé concernant l’efficacité des thérapies manuelles pour les douleurs cervicales. Le protocole expérimental permettait d’obtenir des données pour évaluer la validité conceptuelle, la validité conceptuelle longitudinale, la fidélité test-retest et la sensibilité au changement. Les données de validité conceptuelle (r = 0,67 et 0,61 et 0,42 respectivement pour la validité conceptuelle pré, post traitement et longitudinale), de fidélité test-retest (r = 0,97) et de sensibilité au changement (taille de l’effet = 0,56 et réponse moyenne normalisée = 0,61) sont adéquates pour suggérer une utilisation de cet auto questionnaire pour la gestion des patients ayant des douleurs cervicales.

13. VIEW FROM COLD CALIBRATION BLOCKHOUSE LOOKING DOWN CONNECTING TUNNEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. VIEW FROM COLD CALIBRATION BLOCKHOUSE LOOKING DOWN CONNECTING TUNNEL TO COLD CALIBRATION TEST STAND BASEMENT, SHOWING HARD WIRE CONNECTION (INSTRUMENTATION AND CONTROL). - Marshall Space Flight Center, East Test Area, Cold Calibration Test Stand, Huntsville, Madison County, AL

2. VIEW NORTHWEST FROM LEFT TO RIGHT: COLD CALIBRATION BLOCKHOUSE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. VIEW NORTHWEST FROM LEFT TO RIGHT: COLD CALIBRATION BLOCKHOUSE, COLD CALIBRATION TEST STAND FOR FL ENGINE FOR SATURN V. EXHAUST DUCT IN FOREGROUND. - Marshall Space Flight Center, East Test Area, Cold Calibration Test Stand, Huntsville, Madison County, AL

Diffraction grating-based sensing optofluidic device for measuring the refractive index of liquids.

PubMed

Calixto, Sergio; Bruce, Neil C; Rosete-Aguilar, Martha

2016-01-11

We describe a simple and versatile optical sensing device for measuring refractive index of liquids. The sensor consists of a sinusoidal relief grating in a glass cell. Device calibration is done by pouring in the cell different liquids of known refractive indices. Each time a liquid is poured first order intensity is measured. The fabrication process and testing of the prototype device is described. An application in the measurement of temperature is also presented.

Five-month-old infants have expectations for the accumulation of nonsolid substances.

PubMed

Anderson, Erin M; Hespos, Susan J; Rips, Lance J

2018-06-01

Infants fail to represent quantities of non-cohesive substances in paradigms where they succeed with solid objects. Some investigators have interpreted these results as evidence that infants do not yet have representations for substances. More recent research, however, shows that 5-month-old infants expect objects and substances to behave and interact in different ways. In the present experiments, we test whether infants have expectations for substances when the outcomes are not simply the opposite of those for objects. In Experiment 1, we find that 5-month-old infants expect that when a cup of sand pours behind a screen, it will accumulate in just one pile rather than two. Similarly, infants expect that when two cups of sand pour in separate streams, two distinct piles will accumulate rather than one. Infants look significantly longer at outcomes with an inconsistent number of piles, providing evidence that infants have expectations for how sand accumulates. To test whether the number of cups or the number of pours guided expectations about accumulation, Experiment 2 placed these cues in conflict. This resulted in chance performance, suggesting that, for infants to build expectations about these outcomes, they need both cues (cup and pour) to converge. These findings offer insight into the nature of infants' representations for non-cohesive substances like sand. Copyright © 2018 Elsevier B.V. All rights reserved.

9. COLD CALIBRATION TEST STAND (H1) FROM LEFT TO RIGHT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. COLD CALIBRATION TEST STAND (H-1) FROM LEFT TO RIGHT - WORK BENCH, CONTROL PANEL, CHEMICAL TANK. - Marshall Space Flight Center, East Test Area, Cold Calibration Test Stand, Huntsville, Madison County, AL

Fully Fueled TACOM Vehicle Storage Test Program.

DTIC Science & Technology

1981-12-01

Messrs. H. Hobart, T. Wilson, and T. Hinkley , DRSTA-GSP, U.S. Army Tank Automotive Command (TACOM) for providing both liai- son and fuel-sampling...and its characteristics are as follows: Density, g/ml 0.9 Flash point , *F 140 Fire point , *F 145 Pour point , *F -50 Neutralization No., TAN 25 TBN 130...following characteristics: Density, g/ml 1.05 Flash point , *F 144 Pour point , *F -27.5 Viscosity, cSt, @ 70*F 29 Boron content 7.4% Water (free

5. VIEW NORTHWEST FROM LEFT TO RIGHT: COLD CALIBRATION OBSERVATION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. VIEW NORTHWEST FROM LEFT TO RIGHT: COLD CALIBRATION OBSERVATION BUNKER BACKGROUND, COLD CALIBRATION TOWER. - Marshall Space Flight Center, East Test Area, Cold Calibration Test Stand, Huntsville, Madison County, AL

Analysis of responses of cold pressor tests on pilots and executives

NASA Technical Reports Server (NTRS)

Swaroop, R.

1977-01-01

Statistical analyses were performed to study the relationship between cold pressor test responses and certain medical attributes of a group of 81 pilots and a group of 466 executives. The important results of this study were as follows: There was a significant relationship between a subject's cold pressor test response and his profession (that is, pilot or executive). The executives' diastolic cold pressor test responses were significantly related to their medical conditions, and their families' medical conditions. Significant relationships were observed between executives' diastolic and systolic cold pressor test responses and their history of tranquilizer and cardiac drug use.

Cold Stress and the Cold Pressor Test

ERIC Educational Resources Information Center

Silverthorn, Dee U.; Michael, Joel

2013-01-01

Temperature and other environmental stressors are known to affect blood pressure and heart rate. In this activity, students perform the cold pressor test, demonstrating increased blood pressure during a 1- to 2-min immersion of one hand in ice water. The cold pressor test is used clinically to evaluate autonomic and left ventricular function. This…

40 CFR 1065.703 - Distillate diesel fuel.

Code of Federal Regulations, 2011 CFR

2011-07-01

... CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration... diesel fuel specified for use as a test fuel. See the standard-setting part to determine which grade to... inhibitor. (5) Pour depressant. (6) Dye. (7) Dispersant. (8) Biocide. Table 1 of § 1065.703—Test Fuel...

40 CFR 1065.703 - Distillate diesel fuel.

Code of Federal Regulations, 2013 CFR

2013-07-01

... CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration... diesel fuel specified for use as a test fuel. See the standard-setting part to determine which grade to... inhibitor. (5) Pour depressant. (6) Dye. (7) Dispersant. (8) Biocide. Table 1 of § 1065.703—Test Fuel...

40 CFR 1065.703 - Distillate diesel fuel.

Code of Federal Regulations, 2012 CFR

2012-07-01

... CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration... diesel fuel specified for use as a test fuel. See the standard-setting part to determine which grade to... inhibitor. (5) Pour depressant. (6) Dye. (7) Dispersant. (8) Biocide. Table 1 of § 1065.703—Test Fuel...

Technologies for Future Precision Strike Missile Systems (les Technologies des futurs systemes de missiles pour frappe de precision)

DTIC Science & Technology

2001-07-01

hardware - in - loop (HWL) simulation is also developed...Firings / Engine Tests Structure Test Hardware In - Loop Simulation Subsystem Test Lab Tests Seeker Actuators Sensors Electronics Propulsion Model Aero Model...Structure Test Hardware In - Loop Simulation Subsystem Test Lab Tests Seeker Actuators Sensors Electronics Propulsion Model Aero Model Model

Adhesion testing procedure for hot-poured crack sealants.

DOT National Transportation Integrated Search

2008-11-01

Crack sealing is a common pavement maintenance treatment because it extends pavement service life significantly. : However, crack sealant often fails prematurely due to a loss of adhesion. Because current test methods are mostly : empirical and only ...

The concrete technology of post pouring zone of raft foundation of Hongyun Building B tower

NASA Astrophysics Data System (ADS)

Yin, Suhua; Yu, Liu; Wu, Yanli; Zhao, Ying

2017-08-01

The foundation of Hongyun building B tower is made of raft board foundation which is 3300mm in the thickness concreted pouring amount of large and the late poured band in the pouring settlement formed. The temperature of the pouring settlement was controlled in order to prevent the crack of the construction of the late poured band. The steel of post pouring band was designed and monitorred. The quality of post pouring band quality is guaranteed in the raft concrete foundation of Hongyun Building B tower.

Endectocide activity of a pour-on formulation containing 1.5 per cent ivermectin +0.5 per cent abamectin in cattle.

PubMed

Silva, Heloisa Cristina; Prette, Nancy; Lopes, Welber Daniel Zanetti; Sakamoto, Cláudio Alessandro M; Buzzulini, Carolina; Dos Santos, Thais Rabelo; Cruz, Breno Cayeiro; Teixeira, Weslen F Pires; Felippelli, Gustavo; Carvalho, Rafael Silveira; Maciel, Willian Giquelin; Soares, Vando Edésio; da Costa, Alvimar José

2015-01-01

The present work aimed to evaluate, through ten different studies, the therapeutic efficacy of a new pour-on formulation, containing 1.5 per cent ivermectin +0.5 per cent abamectin, against parasites of cattle. Results obtained on trials against Rhipicephalus (Boophilus) microplus showed that the pour-on combination of 1.5 per cent ivermectin +0.5 per cent abamectin obtained superior efficacy indexes against this ectoparasite, when compared with formulations containing 0.5 per cent ivermectin, 1 per cent ivermectin and the combination of 1 per cent abamectin +20 per cent levamisole. The results of efficacy of the ivermectin+abamectin and the 0.5 per cent ivermectin against Haematobia irritans were similar. Against Cochliomyia hominivorax larvae, all pour-on formulations tested (1.5 per cent ivermectin +0.5 per cent abamectin, 0.5 per cent ivermectin and 0.5 per cent abamectin), as well as 1 per cent doramectin administered subcutaneously, were considered ineffective. Cattle medicated with 1.5 per cent ivermectin +0.5 per cent abamectin, pour-on, remained free from parasitism by Dermatobia hominis larvae during 42 days (96 per cent efficacy), while values superior to 90 per cent were obtained by 0.5 per cent ivermectin (92 per cent) and 0.5 per cent abamectin (93 per cent) until the 42nd and 35th days post treatment, respectively. Against Haemonchus placei and Oesophagostomum radiatum, the pour-on of ivermectin+abamectin showed better efficacy than the 0.5 per cent ivermectin and 0.5 per cent abamectin. As to Cooperia punctata, there was no difference regarding efficacy results obtained by the avermectins combination and abamectin. The pour-on combination of 1.5 per cent ivermectin +0.5 per cent abamectin obtained high efficacy against R. (B.) microplus, D. hominis and some species of cattle gastrointestinal helminths when compared with formulations of 0.5 per cent ivermectin and 0.5 per cent abamectin administered through the same route.

Does acetaminophen/hydrocodone affect cold pulpal testing in patients with symptomatic irreversible pulpitis? A prospective, randomized, double-blind, placebo-controlled study.

PubMed

Fowler, Sara; Fullmer, Spencer; Drum, Melissa; Reader, Al

2014-12-01

The purpose of this prospective randomized, double-blind, placebo-controlled study was to determine the effects of a combination dose of 1000 mg acetaminophen/10 mg hydrocodone on cold pulpal testing in patients experiencing symptomatic irreversible pulpitis. One hundred emergency patients in moderate to severe pain diagnosed with symptomatic irreversible pulpitis of a mandibular posterior tooth randomly received, in a double-blind manner, identical capsules of either a combination of 1000 mg acetaminophen/10 hydrocodone or placebo. Cold testing with Endo-Ice (1,1,1,2 tetrafluoroethane; Hygenic Corp, Akron, OH) was performed at baseline and every 10 minutes for 60 minutes. Pain to cold testing was recorded by the patient using a Heft-Parker visual analog scale. Patients' reaction to the cold application was also rated. Cold testing at baseline and at 10 minutes resulted in severe pain for both the acetaminophen/hydrocodone and placebo groups. Although pain ratings decreased from 20-60 minutes, the ratings still resulted in moderate pain. Patient reaction to cold testing showed that 56%-62% had a severe reaction. Although the reactions decreased in severity over the 60 minutes, 20%-34% still had severe reactions at 60 minutes. Regarding pain and patients' reactions to cold testing, there were no significant differences between the combination acetaminophen/hydrocodone and placebo groups at any time period. A combination dose of 1000 mg of acetaminophen/10 mg of hydrocodone did not statistically affect cold pulpal testing in patients presenting with symptomatic irreversible pulpitis. Patients experienced moderate to severe pain and reactions to cold testing. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Determining predictability and accuracy of thermal and electrical dental pulp tests: An in vivo study.

PubMed

Salgar, Avinash Ramchandra; Singh, Shishir H; Podar, Rajesh S; Kulkarni, Gaurav P; Babel, Shashank N

2017-01-01

Pulp sensitivity testing, even with its limitations and shortcomings, has been and still remains a very helpful aid in endodontic diagnosis. Pulp sensitivity tests extrapolate pulpal health from the sensory response. The aim of the present study was to identify the sensitivity, specificity, positive and negative predictive values (NPVs) of thermal and electrical tests of pulp sensitivity. Pulp tests studied were two cold and heat tests respectively and electrical test. A total of 330 teeth were tested: 198 teeth with vital pulp and 132 teeth with necrotic pulps (disease prevalence of 40%). The ideal standard was established by observing bleeding within the pulp chamber. Sensitivity values of the diagnostic tests were 0.89 and 0.94 for cold test, 0.84 and 0.87 for the heat tests, and 0.75 for electrical pulp test and the specificity values of the diagnostic tests were 0.91 and 0.93 for the cold tests, 0.86 and 0.84 for the heat tests, and 0.90 for electrical pulp test. The NPVs were 0.91 and 0.96 for the cold tests, 0.89 and 0.91 for the heat tests, and 0.84 for electrical pulp test. The positive predictive values were 0.89 and 0.90 for the cold tests, 0.80 and 0.79 for the heat tests and 0.88 for electrical pulp test. The highest accuracy (0.9393) was observed with cold test (icy spray). The cold test done with icy spray was the most accurate method for sensitivity testing.

Development of apparent viscosity test for hot-poured crack sealants.

DOT National Transportation Integrated Search

2008-11-01

Current crack sealant specifications focuses on utilizing simple empirical tests such as penetration, : resilience, flow, and bonding to cement concrete briquettes (ASTM D3405) to measure the ability of the material : to resist cohesive and adhesion ...

Big drinkers: how BMI, gender and rules of thumb influence the free pouring of wine.

PubMed

Smarandescu, Laura; Walker, Doug; Wansink, Brian

2014-11-01

This research examines free pouring behavior and provides an account of how Body Mass Index (BMI) and gender might lead to the overpouring, and consequently the overconsumption of wine. An observational study with young adults investigated how BMI and gender affect free-pouring of wine over a variety of pouring scenarios, and how rules-of-thumb in pouring affect the quantities of alcohol poured by men and women across BMI categories. For men, the amount poured was positively related to BMI. However, BMI did not affect pours by women. The use of the "half glass" rule-of-thumb in pouring reduced the volume of wine poured by over 20% for both men and women. Importantly, this rule-of-thumb substantially attenuated the pours by men at high BMI levels. Increasing awareness of pouring biases represents an early and effective step toward curbing alcohol consumption among men, and especially those who are overweight. Additionally, using a simple "half glass" rule-of-thumb may be an effective way to curb overpouring, despite non-standard glass sizes. Copyright © 2014. Published by Elsevier B.V.

30 CFR 35.21 - Temperature-pressure spray-ignition tests.

Code of Federal Regulations, 2010 CFR

2010-07-01

... device shall be provided. (c) Test procedures. (1) A 21/2-quart sample of the fluid shall be poured into... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Temperature-pressure spray-ignition tests. 35..., EVALUATION, AND APPROVAL OF MINING PRODUCTS FIRE-RESISTANT HYDRAULIC FLUIDS Test Requirements § 35.21...

The Combined Effect of Cold and Moisture on Manual Performance.

PubMed

Ray, Matthew; Sanli, Elizabeth; Brown, Robert; Ennis, Kerri Ann; Carnahan, Heather

2018-02-01

Objective The aim of this study was to investigate the combined effect of cold and moisture on manual performance and tactile sensitivity. Background People working in the ocean environment often perform manual work in cold and wet conditions. Although the independent effects of cold and moisture on hand function are known, their combined effect has not been investigated. Method Participants completed sensory (Touch-Test, two-point discrimination) and motor (Purdue Pegboard, Grooved Pegboard, reef knot untying) tests in the following conditions: dry hand, wet hand, cold hand, and cold and wet hand. Results For the Purdue Pegboard and knot untying tasks, the greatest decrement in performance was observed in the cold-and-wet-hand condition, whereas the decrements seen in the cold-hand and wet-hand conditions were similar. In the Grooved Pegboard task, the performance decrements exhibited in the cold-and-wet-hand condition and the cold-hand condition were similar, whereas no decrement was observed in the wet-hand condition. Tactile sensitivity was reduced in the cold conditions for the Touch-Test but not the two-point discrimination test. The combined effect of cold and moisture led to the largest performance decrements except when intrinsic object properties helped with grasp maintenance. The independent effects of cold and moisture on manual performance were comparable. Application Tools and equipment for use in the cold ocean environment should be designed to minimize the effects of cold and moisture on manual performance by including object properties that enhance grasp maintenance and minimize the fine-dexterity requirements.

Cold Regions - Environmental Testing of Individual Soldier Clothing

DTIC Science & Technology

2011-10-17

Individual Soldier Clothing 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHORS 5d. PROJECT NUMBER 5e. TASK...This Test Operations Procedure (TOP) provides testing guidelines for individual Soldier cold weather clothing and footwear in a cold regions...Soldier clothing , along with its safety, reliability, durability, and performance when exposed to a cold regions environment. 15. SUBJECT TERMS

A-1 Test Stand modifications

NASA Image and Video Library

2011-09-14

Team members check the progress of a liquid nitrogen cold shock test on the A-1 Test Stand at Stennis Space Center on Sept. 15. The cold shock test is used to confirm the test stand's support system can withstand test conditions, when super-cold rocket engine propellant is piped. The A-1 Test Stand is preparing to conduct tests on the powerpack component of the J-2X rocket engine, beginning in early 2012.

Impact of climate change on cold hardiness of Douglas-fir (Pseudotsuga menziesii): environmental and genetic considerations.

PubMed

Bansal, Sheel; St Clair, J Bradley; Harrington, Constance A; Gould, Peter J

2015-10-01

The success of conifers over much of the world's terrestrial surface is largely attributable to their tolerance to cold stress (i.e., cold hardiness). Due to an increase in climate variability, climate change may reduce conifer cold hardiness, which in turn could impact ecosystem functioning and productivity in conifer-dominated forests. The expression of cold hardiness is a product of environmental cues (E), genetic differentiation (G), and their interaction (G × E), although few studies have considered all components together. To better understand and manage for the impacts of climate change on conifer cold hardiness, we conducted a common garden experiment replicated in three test environments (cool, moderate, and warm) using 35 populations of coast Douglas-fir (Pseudotsuga menziesii var. menziesii) to test the hypotheses: (i) cool-temperature cues in fall are necessary to trigger cold hardening, (ii) there is large genetic variation among populations in cold hardiness that can be predicted from seed-source climate variables, (iii) observed differences among populations in cold hardiness in situ are dependent on effective environmental cues, and (iv) movement of seed sources from warmer to cooler climates will increase risk to cold injury. During fall 2012, we visually assessed cold damage of bud, needle, and stem tissues following artificial freeze tests. Cool-temperature cues (e.g., degree hours below 2 °C) at the test sites were associated with cold hardening, which were minimal at the moderate test site owing to mild fall temperatures. Populations differed 3-fold in cold hardiness, with winter minimum temperatures and fall frost dates as strong seed-source climate predictors of cold hardiness, and with summer temperatures and aridity as secondary predictors. Seed-source movement resulted in only modest increases in cold damage. Our findings indicate that increased fall temperatures delay cold hardening, warmer/drier summers confer a degree of cold hardiness, and seed-source movement from warmer to cooler climates may be a viable option for adapting coniferous forest to future climate. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

LPT. Low power assembly and test building (TAN640). Camera facing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LPT. Low power assembly and test building (TAN-640). Camera facing west. Rollup doors to each test cell face east. Concrete walls poured in place. Apparatus at right of view was part of a post-ANP program. INEEL negative no. HD-40-1-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Fuel Property Effects on the Cold Startability of Navy High-Speed Diesel Engines.

DTIC Science & Technology

1985-12-01

0C D 93 77 64.4 85.0 40.6 Cloud Point, 0C D 2500 -13 -18 +16 -5 Pour Point, 0C D 97 -17 <-50 -17 <-50 K . Vis at 400C, m2 /sec D 445 2.75 1.43 2.97...0.75 X 10- 6 X 10-6 X 10-6 X 10-6 K . Vis at 50C, m2/sec D 445 6.65 2.78 8.44 1.17 X 10-6 X 10-6 X 10-6 X 10-6 Distillation, 0C D 2887 IBP 133.2 138.1...volumes, and k is the rate of molal specific heats Cp/Cv. This process is independent of time. However, as the gas temperature is increased, the gas

12. COLD CALIBRATION BLOCKHOUSE BASEMENT VIEW FROM LEFT TO RIGHT, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. COLD CALIBRATION BLOCKHOUSE BASEMENT VIEW FROM LEFT TO RIGHT, CABLE TRAYS, RACKS, CABLE CONNECTION TERMINALS. - Marshall Space Flight Center, East Test Area, Cold Calibration Test Stand, Huntsville, Madison County, AL

40 CFR 86.1432 - Vehicle preparation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... cold temperature compliance pathway, the temperature of the fuel prior to its delivery to the fuel tank... is the Cold CO Test Procedure, performed in accordance with subpart C of this part. (ii) Testing by...). (C) Cold CO Test Procedure, in accordance with subpart C of this part. (c) Soak—(1) Manufacturer's...

40 CFR 86.1432 - Vehicle preparation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... cold temperature compliance pathway, the temperature of the fuel prior to its delivery to the fuel tank... is the Cold CO Test Procedure, performed in accordance with subpart C of this part. (ii) Testing by...). (C) Cold CO Test Procedure, in accordance with subpart C of this part. (c) Soak—(1) Manufacturer's...

First impression versus extended usage: a comparison of product testing methodologies for perfume.

PubMed

Shalofsky, I

1993-04-01

Synopsis In the fine fragrance industry, unlike many other fast moving consumer goods (fmcg) industries, systematic consumer product-testing has usually been conspicuous by its absence. The reasons are varied, including perfume's own traditions rooted in fashion rather than in marketing, the reluctance of perfumers to see their creations tested, the frequently (and perhaps, surprisingly) short lead times accorded for new product development and, of course, costs. When consumer product-testing is carried out, it is often limited for these same reasons, to 'sniff-testing', which, in the perfume industry, is equivalent to 'first impression' testing. This paper suggests that such sniff-testing may not only be unreliable, but perhaps more unreliable for the perfume category than has been realized hitherto. Reference is made to two consumer research studies on perfume, a qualitative project in France, followed by a quantitative exercise in the UK. A comparison is made between in-home test and sniff-test results for the same set of perfumes, which illustrates the limitations of sniff-testing in general, and the misleading results that it may produce, in particular. A major implication is that perfume is one product category which should be tested in extended usage, and not just for 'first impressions'. Résumé Dans l'industrie de la parfumerie fine, contrairement aux autres industries de produits de grande consommation, les tests consommateurs systématiques sont rarement utilisés. Les raisons sont diverses; les traditions propres du parfum tournées vers la mode plutôt que vers le marketing, le refus des parfumeurs de voir leurs créations subir des tests, les délais étonnamment courts pour le développement d'un nouveau produit et, bien sûr, le coût. Lorsqu'un test consommateurs est effectué, il se résume généralement pour ces mêmes raisons, en un test 'sniff', ce qui, dans l'industrie du parfum équivaut à un test de 'première impression'. Cet article montre que ces tests 'sniff' sont encore moins fiables pour le parfum que l'on avait pensé jusqu'à maintenant. Il est fait référence à deux tests consommateurs sur le parfum, un projet qualitatif en France, suivi par un exercice quantitatif effectué en Grande Bretagne. La comparaison entre les tests réalisés à domicile d'une part, et en sale d'autre part, montre que, pour les mêmes parfums, les résultats obtenus peuvent être erronés. Une des conclusions principales est que le parfum est un produit qui devrait être testé sur une longue période et non pas sur une première impression.

Texture analysis of oxide dispersion strengthened (ODS) Fe alloys by X-ray and neutron diffraction

NASA Astrophysics Data System (ADS)

Béchade, J. L.; Mathon, M. H.; Branger, V.; Réglé, H.; Alamo, A.

2002-07-01

The ferritic ODS alloys studied were obtained by mechanical alloying. This strengthening method is very attractive, in particular for nuclear applications. In order to ensure the alloy a good compromise between mechanical resistance and ductility at high temperatures, it is necessary to control the microstructure and in particular the evolution during the recrystallization. First, a preliminary study, performed by X ray diffraction and optical microscopy, shows several grain growth mechanisms ; in particular, the “abnormal” grain growth mechanism which conducts to a large grain size [1], [2]. After annealing (3600s at 1470^{circ}C), the 30% cold-worked (swaging) alloys exhibit an heterogeneous microstructure with a large grains size ( 200 to 500 μm) in the heart and near the surface of the material when the intermediate zone is inhabited by small grains ( 1 μm). Fora higher cold-work level (60%), large size grains are only present in the periphery of the material. On account of the large grain size and strong heterogeneity of the microstructure, texture analysis using laboratory x-ray beam in not well adapted and so we have decided to use neutron beam. The neutron diffraction texture analysis has been performed at the Laboratoire Léon Brillouin on the 6T1 diffractometer on 2 different rods of the alloy (corresponding to the reduction ratios of 30% and 60%). Specific samples have been machined to characterise separately the zones with a different microstructure. After deformation, the alloys exhibit a typical α-fibre texture \\{ hkl \\} <1l0> whatever the area of the sample and the reduction ratio. After recrystallization, a very inhomogeneous texture is evidenced through the thickness of the sample, in particular for the rod deformed with a reduction ratio of 30% : in the heart and in the periphery of the rod, a “single-crystal” type texture is observed; the a fibre remains for the intermediate diameter of the rod. For the rod cold rolled with a reduction ratio of 60%, the α-fibre keeps on the heart of the material and as in the precedent case, a “single-crystal” type texture is observed near the surface of the sample. EBSD measurements have been performed to explicit at a local scale this behaviour and in order to furnish some input data for the simulation of static recrystallization. Les aciers ferritiques avec dispersion d'oxydes étudiés sont obtenus par métallurgie des poudres, ce qui leur confère une résistance mécanique accrue à haute température notamment pour des applications nucléaires. La difficulté pour l'utilisation de tels alliages réside dans la maîtrise de leur microstructure au cours de l'élaboration en particulier durant la recristallisation. Une première étude en diffraction des rayons-x et en métallographie optique a permis de révéler différents mécanismes de croissance du grain lors de la recristallisation, notamment une croissance “anormale” conduisant à une taille de grain très importante [t], [2]. Après recuit (3600s à 1470^{circ}C), précédé par un écrouissage de 30% sur des barres (par martelage) on voit apparaître une microstructure hétérogène à gros grains ( 200 à 500 μm) au coeur et en surface externe de la barre alors que la zone intermédiaire est peuplée de grains fins (sim 1 μm). Pour un écrouissage plus élevé (60%), après le même recuit, on ne voit apparaître des gros grains qu'en périphérie de la barre. Pour ce type de microstructure fortement hétérogène et à gros grains, la diffraction des rayons-x pour l'analyse de texture est mal adaptée, ce qui nous a conduit à utiliser la diffraction des neutrons sur le diffractomètre 6TI du Laboratoire Léon Brillouin. Les deux matériaux, écrouis de 30% et 60%, ont été analysés en réalisant des échantillons particuliers permettant d'étudier séparément le coeur et la périphérie. Après déformation, les deux échantillons présentent une texture de fibre α \\{ hkl \\} <1l0> en tout point de la barre. Après recristallisation, on retrouve une texture très hétérogène suivant le rayon de la barre, notamment après 30% : le coeur et la périphérie de la barre présentent une texture de type “mono-cristal”, la zone intermédiaire restant une fibre α. Après écrouissage de 60%, on garde la fibre α au coeur de la barre, la périphérie présentant, comme pour l'écrouissage précédent, une texture de type “mono-cristal”. Des analyses en EBSD ont également été réalisées pour foumir des éléments de compréhension sur les mécanismes locaux de recristallisation afin de simuler la recristallisation statique de ses alliages via une approche numérique.

Dependence of the pour point of diesel fuels on the properties of the initial components

NASA Technical Reports Server (NTRS)

Ostashov, V. M.; Bobrovskiy, S. A.

1979-01-01

An analytical expression is obtained for the dependence of the pour point of diesel fuels on the pour point and weight relationship of the initial components. For determining the pour point of a multicomponent fuel mixture, it is assumed that the mixture of two components has the pour point of a separate equivalent component, then calculating the pour point of this equivalent component mixed with a third component, etc.

Summary Report For The Analysis Of The Sludge Batch 7b (Macrobatch 9) DWPF Pour Stream Glass Sample For Canister S04023

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, F. C.

2013-11-18

In order to comply with the Defense Waste Processing Facility (DWPF) Waste Form Compliance Plan for Sluldge Batch 7b, Savannah River National Laboratory (SRNL) personnel characterized the Defense Waste Processing Facility (DWPF) pour stream (PS) glass sample collected while filling canister S04023. This report summarizes the results of the compositional analysis for reportable oxides and radionuclides and the normalized Product Consistency Test (PCT) results. The PCT responses indicate that the DWPF produced glass that is significantly more durable than the Environmental Assessment glass.

Impact of a bladder scan protocol on discharge efficiency within a care pathway for ambulatory inguinal herniorraphy.

PubMed

Antonescu, I; Baldini, G; Watson, D; Kaneva, P; Fried, G M; Khwaja, K; Vassiliou, M C; Carli, F; Feldman, L S

2013-12-01

Postoperative urinary retention (POUR) is a common complication of ambulatory inguinal herniorraphy, with an incidence reaching 38%, and many surgeons require patients to void before discharge. This study aimed to assess whether the implementation of a bladder scan-based voiding protocol reduces the time until discharge after ambulatory inguinal herniorraphy without increasing the rate of POUR. As part of a perioperative care pathway, a protocol was implemented to standardize decision making after elective inguinal hernia repair (February 2012). Patients were assessed with a bladder scan, and those with <600 mL of urine were discharged home, whereas those with more than 600 mL of urine had an in-and-out catheterization before discharge. The patients received written information about urinary symptoms and instructions to present to the emergency department if they were unable to void at home. An audit of scheduled outpatient inguinal hernia repairs between October 2011 and July 2012 was performed. Comparisons were made using the t test, Fisher's exact test, and Wilcoxon rank sum test where appropriate. Statistical significance was defined a priori as a p value lower than 0.05. During the study period, 124 patients underwent hernia repair: 60 before and 64 after implementation of the protocol. The findings showed no significant differences in patient characteristics, laparoscopic approach (35 vs. 33%; p = 0.80), proportion receiving general anesthesia (70 vs. 73%; p = 0.67), or amount of intravenous fluids given (793 vs. 663 mL; p = 0.07). The proportion of patients voiding before discharge was higher after protocol implementation (73 vs. 89%; p = 0.02). The protocol had no impact on median time to discharge (190 vs. 205 min; p = 0.60). Only one patient in each group presented to the emergency department with POUR (2%). After ambulatory inguinal herniorraphy, implementation of a bladder scan-based voiding protocol did not result in earlier discharge. The incidence of POUR was lower than reported in the literature.

Three-dimensional simulation of helix traveling-wave tube cold-test characteristics using MAFIA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kory, C.L.

1996-12-31

A critically important step in the traveling-wave tube (TWT) design process is the cold-testing of the slow-wave circuit for dispersion, beam interaction impedance and RF losses. Experimental cold-tests can be very time-consuming and expensive, thus limiting the freedom to examine numerous variations to the test circuit. This makes the need for computational methods crucial as they can lower cost, reduce tube development time and allow the freedom to introduce novel and improved designs. The cold-test parameters have been calculated for a C-Band Northrop-Grumman helix TWT slow-wave circuit using MAFIA, the three-dimensional electromagnetic finite-integration computer code. Measured and simulated cold-test datamore » for the Northrop-Grumman helix TWT including dispersion, impedance and attenuation will be presented. Close agreement between simulated and measured values of the dispersion, impedance and attenuation has been obtained.« less

Relationships of self-identified cold tolerance and cold-induced vasodilatation in the finger

NASA Astrophysics Data System (ADS)

Park, Joonhee; Lee, Joo-Young

2016-04-01

This study was conducted to investigate relationships of self-identified cold tolerance and cold-induced vasodilatation (CIVD) in the finger. Nine males and 34 females participated in the following 2 tests: a CIVD test and a self-reported survey. The CIVD test was conducted 30-min cold-water immersion (3.8 ± 0.3 °C) of the middle finger at an air temperature of 27.9 ± 0.1 °C. The self-reported questionnaire consisted of 28 questions about whole and local body cold and heat tolerances. By a cluster analysis on the survey results, the participants were divided into two groups: high self-identified cold tolerance (HSCT, n = 25) and low self-identified cold tolerance (LSCT, n = 18). LSCT had lower self-identified cold tolerance ( P < 0.001), preferred hot thermal stimulation ( P = 0.006), and wore heavier clothing during daily life ( P < 0.001) than HSCT. LSCT had significantly lower maximal finger temperatures ( T max) ( P = 0.040), smaller amplitude ( P = 0.029), and delayed onset time of CIVD ( P = 0.080) when compared to HSCT. Some questions examining the self-identified cold or heat tolerance had relationships with cold tolerance index, T max, and amplitude ( P < 0.1). These results indicate that self-identified cold tolerance classified through a standardized survey could be a good index to predict physiological cold tolerance.

Relationships of self-identified cold tolerance and cold-induced vasodilatation in the finger.

PubMed

Park, Joonhee; Lee, Joo-Young

2016-04-01

This study was conducted to investigate relationships of self-identified cold tolerance and cold-induced vasodilatation (CIVD) in the finger. Nine males and 34 females participated in the following 2 tests: a CIVD test and a self-reported survey. The CIVD test was conducted 30-min cold-water immersion (3.8 ± 0.3 °C) of the middle finger at an air temperature of 27.9 ± 0.1 °C. The self-reported questionnaire consisted of 28 questions about whole and local body cold and heat tolerances. By a cluster analysis on the survey results, the participants were divided into two groups: high self-identified cold tolerance (HSCT, n = 25) and low self-identified cold tolerance (LSCT, n = 18). LSCT had lower self-identified cold tolerance (P < 0.001), preferred hot thermal stimulation (P = 0.006), and wore heavier clothing during daily life (P < 0.001) than HSCT. LSCT had significantly lower maximal finger temperatures (T max) (P = 0.040), smaller amplitude (P = 0.029), and delayed onset time of CIVD (P = 0.080) when compared to HSCT. Some questions examining the self-identified cold or heat tolerance had relationships with cold tolerance index, T max, and amplitude (P < 0.1). These results indicate that self-identified cold tolerance classified through a standardized survey could be a good index to predict physiological cold tolerance.

Les campagnes communautaires de promotion du depistage VIH en Afrique de l’Ouest : perceptions des usagers au Burkina Faso

PubMed Central

Desclaux, Alice; Ky-Zerbo, Odette; Somé, Jean-François; Makhlouf-Obermeyer, Carla

2014-01-01

Résumé La politique actuelle de lutte contre le sida qui repose sur l’extension de l’accès aux traitements et à la prévention exige qu’une proportion élevée de la population connaisse son statut en matière de VIH. Pour cela, l’OMS a proposé le développement de stratégies communautaires délivrant le dépistage et le conseil au-delà des services de soins, comme le test à domicile ou les campagnes de sensibilisation et dépistage de grande envergure, appliqués en Afrique australe et de l’Est. Pour définir les stratégies pertinentes dans des régions de basse prévalence comme l’Afrique de l’Ouest, les expériences communautaires de promotion du dépistage doivent y être évaluées. Cet article présente une évaluation des campagnes au Burkina Faso du point de vue des usagers. Dans le cadre d’un projet sur les pratiques et l’éthique du dépistage dans quatre pays africains (MATCH), une enquête qualitative spécifique a été menée pendant la campagne de 2008, auprès de personnes ayant fait le test pendant la campagne, ayant fait le test hors campagne ou n’ayant pas fait le test. Les appréciations sont globalement très favorables aux campagnes, notamment à cause de l’information dispensée, l’accessibilité des sites, la gratuité du test, la qualité des services et l’effet d’entrainement. Les limites ou critiques sont essentiellement liées à l’affluence ou à la crainte de ne pas être soutenu en cas de résultat positif. La démarche de recours au test ne fait plus l’objet de suspicion, au moins pendant la campagne. Cette « normalisation » du recours au test et la mobilisation collective facilitent des pratiques en groupe, ce qui peut rendre difficile de garder son statut VIH secret. L’évaluation des campagnes par les usagers les présente comme une opportunité pour accéder facilement au test et pour communiquer à ce sujet dans divers espaces sociaux à partir des informations délivrées sur le VIH. PMID:24755264

40 CFR 1060.515 - How do I test EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions?

Code of Federal Regulations, 2011 CFR

2011-07-01

... and EPA Cold-Weather Fuel Lines for permeation emissions? 1060.515 Section 1060.515 Protection of... Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions? Measure emission as follows for EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines: (a) Prior to permeation testing, use good...

40 CFR 1060.515 - How do I test EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions?

Code of Federal Regulations, 2013 CFR

2013-07-01

... and EPA Cold-Weather Fuel Lines for permeation emissions? 1060.515 Section 1060.515 Protection of... Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions? Measure emission as follows for EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines: (a) Prior to permeation testing, use good...

40 CFR 1060.515 - How do I test EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions?

Code of Federal Regulations, 2012 CFR

2012-07-01

... and EPA Cold-Weather Fuel Lines for permeation emissions? 1060.515 Section 1060.515 Protection of... Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions? Measure emission as follows for EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines: (a) Prior to permeation testing, use good...

40 CFR 1060.515 - How do I test EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions?

Code of Federal Regulations, 2010 CFR

2010-07-01

... and EPA Cold-Weather Fuel Lines for permeation emissions? 1060.515 Section 1060.515 Protection of... Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions? Measure emission as follows for EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines: (a) Prior to permeation testing, use good...

40 CFR 1060.515 - How do I test EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions?

Code of Federal Regulations, 2014 CFR

2014-07-01

... and EPA Cold-Weather Fuel Lines for permeation emissions? 1060.515 Section 1060.515 Protection of... Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines for permeation emissions? Measure emission as follows for EPA Nonroad Fuel Lines and EPA Cold-Weather Fuel Lines: (a) Prior to permeation testing, use good...

Baroreflex modulation of muscle sympathetic nerve activity during cold pressor test in humans

NASA Technical Reports Server (NTRS)

Cui, Jian; Wilson, Thad E.; Crandall, Craig G.

2002-01-01

The purpose of this project was to test the hypothesis that baroreceptor modulation of muscle sympathetic nerve activity (MSNA) and heart rate is altered during the cold pressor test. Ten subjects were exposed to a cold pressor test by immersing a hand in ice water for 3 min while arterial blood pressure, heart rate, and MSNA were recorded. During the second and third minute of the cold pressor test, blood pressure was lowered and then raised by intravenous bolus infusions of sodium nitroprusside and phenylephrine HCl, respectively. The slope of the relationship between MSNA and diastolic blood pressure was more negative (P < 0.005) during the cold pressor test (-244.9 +/- 26.3 units x beat(-1) x mmHg(-1)) when compared with control conditions (-138.8 +/- 18.6 units x beat(-1) x mmHg(-1)), whereas no significant change in the slope of the relationship between heart rate and systolic blood pressure was observed. These data suggest that baroreceptors remain capable of modulating MSNA and heart rate during a cold pressor test; however, the sensitivity of baroreflex modulation of MSNA is elevated without altering the sensitivity of baroreflex control of heart rate.

Steel erected at A-3 Test Stand

NASA Image and Video Library

2008-10-24

Fabricated steel began arriving by truck Oct. 24 for construction of the A-3 Test Stand that will be used to test the engine for the nation's next generation of moon rockets. Within days workers from Lafayette Steel Erector Inc. began assembling the 16 steel stages needed on the foundation and footings poured in the previous year.

Steel erected at A-3 Test Stand

NASA Technical Reports Server (NTRS)

2008-01-01

Fabricated steel began arriving by truck Oct. 24 for construction of the A-3 Test Stand that will be used to test the engine for the nation's next generation of moon rockets. Within days workers from Lafayette Steel Erector Inc. began assembling the 16 steel stages needed on the foundation and footings poured in the previous year.

Accuracy of Gypsum Casts after Different Impression Techniques and Double Pouring

PubMed Central

Silva, Stephania Caroline Rodolfo; Messias, Aion Mangino; Abi-Rached, Filipe de Oliveira; de Souza, Raphael Freitas; Reis, José Maurício dos Santos Nunes

2016-01-01

This study evaluated the accuracy of gypsum casts after different impression techniques and double pouring. Ten patients were selected and for each one it was obtained 5 partial putty/wash impressions with vinyl polysiloxane (VPS) material from teeth #13 to #16 with partial metal stock trays. The following techniques were performed: (1) one-step; two-step relief with: (2) PVC film; (3) slow-speed tungsten carbide bur and scalpel blade, (4) small movements of the tray and (5) without relief—negative control. The impressions were disinfected with 0.5% sodium hypochlorite for 10 minutes and stored during 110 and 230 minutes for the first and second pouring, respectively, with type IV gypsum. Three intra-oral lateral photographs of each patient were taken using a tripod and a customized radiographic positioner. The images were imported into ImageJ software and the total area of the buccal surface from teeth #13 to #16 was measured. A 4.0% coefficient of variance was criterion for using these measurements as Baseline values. The casts were photographed and analyzed using the same standardization for the clinical images. The area (mm2) obtained from the difference between the measurements of each gypsum cast and the Baseline value of the respective patient were calculated and analyzed by repeated-measures two way-ANOVA and Mauchly’s Sphericity test (α = 0.05). No significant effect was observed for Impression technique (P = 0.23), Second pouring (P = 0.99) and their interaction (P = 0.25). The impression techniques and double pouring did not influence the accuracy of the gypsum casts. PMID:27736967

Accuracy of Gypsum Casts after Different Impression Techniques and Double Pouring.

PubMed

Silva, Stephania Caroline Rodolfo; Messias, Aion Mangino; Abi-Rached, Filipe de Oliveira; de Souza, Raphael Freitas; Reis, José Maurício Dos Santos Nunes

2016-01-01

This study evaluated the accuracy of gypsum casts after different impression techniques and double pouring. Ten patients were selected and for each one it was obtained 5 partial putty/wash impressions with vinyl polysiloxane (VPS) material from teeth #13 to #16 with partial metal stock trays. The following techniques were performed: (1) one-step; two-step relief with: (2) PVC film; (3) slow-speed tungsten carbide bur and scalpel blade, (4) small movements of the tray and (5) without relief-negative control. The impressions were disinfected with 0.5% sodium hypochlorite for 10 minutes and stored during 110 and 230 minutes for the first and second pouring, respectively, with type IV gypsum. Three intra-oral lateral photographs of each patient were taken using a tripod and a customized radiographic positioner. The images were imported into ImageJ software and the total area of the buccal surface from teeth #13 to #16 was measured. A 4.0% coefficient of variance was criterion for using these measurements as Baseline values. The casts were photographed and analyzed using the same standardization for the clinical images. The area (mm2) obtained from the difference between the measurements of each gypsum cast and the Baseline value of the respective patient were calculated and analyzed by repeated-measures two way-ANOVA and Mauchly's Sphericity test (α = 0.05). No significant effect was observed for Impression technique (P = 0.23), Second pouring (P = 0.99) and their interaction (P = 0.25). The impression techniques and double pouring did not influence the accuracy of the gypsum casts.

A Rare Non-Hemolytic Case of Idiopathic Cold Agglutinin Disease.

PubMed

Erkus, Edip; Kocak, Mehmet Z; Aktas, Gulali; Ozen, Mehmet; Atak, Burcin M; Duman, Tuba T; Tekce, Buket K; Savli, Haluk

2018-06-01

Cold agglutinin disease is a very rare condition associated with agglutination of erythrocytes in cold environment usually due to IgM type antibodies. Other than hemolytic anemias, it may interfere with routine hemogram tests due to miscalculation of red blood cell count (RBC) and other hemogram parameters calculated with involvement of RBC. Awareness of the condition is important to overcome laboratory errors. We studied a peripheral blood smear and repeated the hemogram test at 37°C to establish the diagnosis of cold agglutinin disease. Initial hemogram test results of the fifty-eight year-old man was as follows: RBC: 1.34 M/µL, hemoglobin (Hb): 12.4 g/dL, hematocrit (Htc): 11.8%, mean corpuscular hemoglobin (MCH): 92.4 pg, and mean corpuscular hemoglobin concentration (MCHC): 105 gr/dL. Despite the standard indirect Coombs test being negative, repeated tests at room temperature was 4+. We suspected cold agglutinin disease and repeated the hemogram test using the Bain-Marie method at 37°C and the test results showed RBC: 3.4 M/µL, hemoglobin: 12.6 g/dL, hematocrit: 30.2%, MCH: 31.7 pg, and MCHC: 41.8 g/dL. Inappropriate hemogram results may be a sign of underlying cold agglutinin disease. Hemolytic anemia not always accompanies the disease; however, cold exposure may trigger erythrocyte agglutination in vitro and may cause erratic laboratory results.

NORTH BASEMENT WALL. IBEAM COLUMNS HAVE BEEN ENCASED IN CONCRETE. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTH BASEMENT WALL. I-BEAM COLUMNS HAVE BEEN ENCASED IN CONCRETE. STEEL BEAMS LAY ACROSS FIRST FLOOR AWAITING CONCRETE POUR. CAMERA LOOKS SOUTHWEST. INL NEGATIVE NO. 735. Unknown Photographer, 10/6/1950 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

A test system to quantify inoculum in runoff from Phytophthora ramorum-infected plant roots

USDA-ARS?s Scientific Manuscript database

Foliar hosts of Phytophthora ramorum are often susceptible to root infection, but the epidemiological significance of such infections is unknown. We used a standardized test system to study inoculum in runoff from root-infected Viburnum tinus cuttings. Viburnum were inoculated by pouring a sporang...

Cold Regions Test of Indirect Fire Weapons Ammunition

DTIC Science & Technology

1983-03-08

COLD REGIONS TEST OF INDIRECT FIRE WEAPONS AMMUNITION Paragraph 1 . SCOPE. 1 2. FACILITIES AND INSTRUMENTATION .......... 3. PREPARATION FOR TEST...A- 1 B. Data Collection Sheets ..... .............. B- 1 C. References ..... .................... ... C- 1 D. Cold-Dry...Uniform .D...... .. ... .. ... 0- 1 1 . SCOPE. The procedures outlined in this TOP are designed to determine the c-h-arac-teristics of indirect artillery

Concordance et apports de l'hystérosalpingographie et de la cœlioscopie dans l'exploration tubaire et pelvienne en cas d'infertilité

PubMed Central

Kehila, Mehdi; Ben Hmid, Rim; Ben Khedher, Sonia; Mahjoub, Sami; Channoufi, Mohamed Bedis

2014-01-01

Introduction La coelioscopie et l'hystérosalpingographie sont les deux procédures usuellement admises pour l'exploration tubaire et pelvienne en cas d'infertilité. Les objectifs de ce travail etaient de comparer les données de l'Hystérosalpingographie à celles de la coelioscopie chez des patientes explorées pour infertilité et voir l'apport de l'une par rapport à l'autre. Méthodes Etude prospective menée au service C du centre de maternité et de néonatologie de Tunis, s’étendant sur 15 mois, colligeant 120 patientes suivies pour infertilité ayant bénéficié d'une HSG suivie d'une coelioscopie. Résultats L’âge moyen de nos patientes était de 35,3 ans. L'infertilité était primaire dans 56,7% des cas et secondaire dans 43,7% des cas. Sa durée moyenne était de 48,9 mois. Le test statistique de concordance Kappa entre les 2 examens était de 0.42 pour les obstructions tubaires en général, de 0.48 pour les obstructions tubaires proximales et de 0.53 pour les obstructions tubaires distales indiquant une concordance modérée dans tous les cas. La coelioscopie a permis d'objectiver en plus une endométriose pelvienne dans 7% des cas, des adhérences pelviennes dans 33% des cas et des trompes perméables mais d'aspect pathologique dans 20% des cas. Conclusion Il existe un intérêt d′associer, chaque fois que c′est possible, l'HSG et la coelioscopie dans l'exploration du pelvis féminin dans le cadre de l'infertilité. Aucun de ces deux examens n'est parfait. Leurs résultats sont complémentaires. PMID:25374631

Wire and Cable Cold Bending Test

NASA Technical Reports Server (NTRS)

Colozza, Anthony

2010-01-01

One of the factors in assessing the applicability of wire or cable on the lunar surface is its flexibility under extreme cold conditions. Existing wire specifications did not address their mechanical behavior under cold, cryogenic temperature conditions. Therefore tests were performed to provide this information. To assess this characteristic 35 different insulated wire and cable pieces were cold soaked in liquid nitrogen. The segments were then subjected to bending and the force was recorded. Any failure of the insulation or jacketing was also documented for each sample tested. The bending force tests were performed at room temperature to provide a comparison to the change in force needed to bend the samples due to the low temperature conditions. The results from the bending tests were plotted and showed how various types of insulated wire and cable responded to bending under cold conditions. These results were then used to estimate the torque needed to unroll the wire under these low temperature conditions.

Concrete probe-strength study : final report.

DOT National Transportation Integrated Search

1969-12-01

The Windsor probe - test system was evaluated for determining compressive strength of concrete by comparing probe strengths against cylinder and core strengths from both laboratory and field-poured concrete. Advantages and disadvantages of this syste...

Resistance to densification, tensile strength and capsule-filling performance of some pharmaceutical diluents.

PubMed

Nikolakakis, I; Aragon, O B; Malamataris, S

1998-07-01

The purpose of this study was to compare some indicators of capsule-filling performance, as measured by tapped density under different conditions, and elucidate possible quantitative relationships between variation of capsule fill-weight (%CV) and gravitational and inter-particle forces (attractive or frictional) derived from measurements of particle size, true density, low compression and tensile strength. Five common pharmaceutical diluents (lactose, maize starch, talc, Emcocel and Avicel) were investigated and two capsule-filling methods (pouring powder and dosator nozzle) were employed. It was found that for the pouring-type method the appropriateness of Hausner's ratio (HR), Carr's compressibility index (CC%) and Kawakita's constant (alpha) as indicators of capsule fill-weight variation decreases in the order alpha > CC% > HR; the appropriateness of these indicators also decreases with increasing cylinder size and with impact velocity during tapping. For the dosator-type method the appropriateness of the indicators decreases in the order HR > CC% > alpha, the opposite of that for the pouring-type method; the appropriateness of the indicators increases with decreasing cylinder size and impact velocity. The relationship between %CV and the ratio of inter-particle attractive to gravitational forces calculated from measurements of particle size and true density (Fvdw/Wp) was more significant for the pouring-type capsule-filling method. For the dosator-type method a significant relationship (1% level) was found between %CV and the product of Fvdw/Wp and a function expressing the increase, with packing density (p(f)), in the ratio of frictional to attractive inter-particle forces derived from compression (P) and tensile-strength (T) testing, d(log(P/T))/d(p(f)). The value of tapped density in predictions of capsule-filling performance is affected by the testing conditions in a manner depending on the filling method applied. For the pouring-type method predictions can be based on the ratio of attractive (inter-particle) to gravitational forces, whereas for the dosator-type method the contribution of frictional and attractive forces should, because of packing density change, also be taken into account.

Accurate Cold-Test Model of Helical TWT Slow-Wave Circuits

NASA Technical Reports Server (NTRS)

Kory, Carol L.; Dayton, James A., Jr.

1997-01-01

Recently, a method has been established to accurately calculate cold-test data for helical slow-wave structures using the three-dimensional electromagnetic computer code, MAFIA. Cold-test parameters have been calculated for several helical traveling-wave tube (TWT) slow-wave circuits possessing various support rod configurations, and results are presented here showing excellent agreement with experiment. The helical models include tape thickness, dielectric support shapes and material properties consistent with the actual circuits. The cold-test data from this helical model can be used as input into large-signal helical TWT interaction codes making it possible, for the first time, to design a complete TWT via computer simulation.

Cold Regions Environmental Protection and Durability Test of Clothing.

DTIC Science & Technology

1983-07-08

17 AD-A130 482 COLD REGIONS ENVIRONMENTAL PROTECTION AND DURABILITY 1 / TEST OF CLDTHING(U) *ARMY TEST AND EVALGATION COMMAND ABERDEEN PROVING GROUND...MD 08 JUL 83 TOP-10-2510 UNCLASSIFIED FDA 6/7 -Lm U= 1,2 2 340 12.0IIHI . 1 L1.8 j$jfLi25 .411 .6 MICROCOPY RESOLUTION TEST CHART NT’NL BUREAU C’ N j...July 1983 AD NO. COLD REGIONS ENVIRONMENTAL PROTECTION AND DURABILITY TEST OF CLOTHING Page 1 SCOPE .................................. 1 2 FACILITIES

Resource Prospector Propulsion Cold Flow Test

NASA Technical Reports Server (NTRS)

Williams, Hunter; Pederson, Kevin; Dervan, Melanie; Holt, Kimberly; Jernigan, Frankie; Trinh, Huu; Flores, Sam

2014-01-01

For the past year, NASA Marshall Space Flight Center and Johnson Space Center have been working on a government version of a lunar lander design for the Resource Prospector Mission. A propulsion cold flow test system, representing an early flight design of the propulsion system, has been fabricated. The primary objective of the cold flow test is to simulate the Resource Prospector propulsion system operation through water flow testing and obtain data for anchoring analytical models. This effort will also provide an opportunity to develop a propulsion system mockup to examine hardware integration to a flight structure. This paper will report the work progress of the propulsion cold flow test system development and test preparation. At the time this paper is written, the initial waterhammer testing is underway. The initial assessment of the test data suggests that the results are as expected and have a similar trend with the pretest prediction. The test results will be reported in a future conference.

Recommended Practices for Measurement of Gas Path Pressures and Temperatures for Performance Assessment of Aircraft Turbine Engines and Components (Les Methodes Recommandees pour la Mesure de la Pression et de la Temperature de la Veine Gazeuse en Vue de l’Evaluation des Performances des Turbines Aeronautiques et de leurs Composants

DTIC Science & Technology

1990-06-01

reduction software , prior to converting all remaining test which requires internal compensation. T he r sidual effect is pressures to engineering units...Reduction Conversion of Millivolts to Engineering Units. Carrying out numerical integrations to obtain area and mass weighted averages for various...Performance Assessment of Aircraft Turbine Engines and Components (Les MWthodes Recommande’es pour la Mesure de la Pression et de ]a Temperature de la

40 CFR 86.113-94 - Fuel specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., antirust, pour depressant, dye, dispersant and biocide. Fuels specified for emissions testing are intended... detected down to a concentration in air of not over 1/5 (one-fifth) of the lower limit of flammability. (2...

[Cold-induced urticaria].

PubMed

Delorme, N; Drouet, M; Thibaudeau, A; Verret, J L

2002-09-01

Cold urticaria is characterized by the development of urticaria, usually superficial and/or angioedematous reaction after cold contact. It was found predominantly in young women. The diagnosis is based on the history and ice cube test. Patients with a negative ice cube test may have represented systemic cold urticaria (atypical acquired cold urticaria) induced by general body cooling. The pathogenesis is poorly understood. Cold urticaria can be classified into acquired and familial disorders, with an autosomal dominant inheritance. Idiopathic cold urticaria is most common type but the research of a cryopathy is necessary. Therapy is often difficult. It is essential that the patient be warned of the dangers of swimming in cold water because systemic hypotension can occur. H1 antihistamines can be used for treatment of cold urticaria but the clinical responses are highly variable. The combination with an H2 antagonists is more effective. Doxepin may be useful in the treatment. Leukotriene receptor antagonists may be a novel, promising drug entity. In patients who do not respond to previous treatments, induction of cold tolerance may be tried.

Preliminary Technology Maturation Plan for Immobilization of High-Level Waste in Glass Ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vienna, John D.; Crum, Jarrod V.; Sevigny, Gary J.

2012-09-30

A technology maturation plan (TMP) was developed for immobilization of high-level waste (HLW) raffinate in a glass ceramics waste form using a cold-crucible induction melter (CCIM). The TMP was prepared by the following process: 1) define the reference process and boundaries of the technology being matured, 2) evaluate the technology elements and identify the critical technology elements (CTE), 3) identify the technology readiness level (TRL) of each of the CTE’s using the DOE G 413.3-4, 4) describe the development and demonstration activities required to advance the TRLs to 4 and 6 in order, and 5) prepare a preliminary plan tomore » conduct the development and demonstration. Results of the technology readiness assessment identified five CTE’s and found relatively low TRL’s for each of them: • Mixing, sampling, and analysis of waste slurry and melter feed: TRL-1 • Feeding, melting, and pouring: TRL-1 • Glass ceramic formulation: TRL-1 • Canister cooling and crystallization: TRL-1 • Canister decontamination: TRL-4 Although the TRL’s are low for most of these CTE’s (TRL-1), the effort required to advance them to higher values. The activities required to advance the TRL’s are listed below: • Complete this TMP • Perform a preliminary engineering study • Characterize, estimate, and simulate waste to be treated • Laboratory scale glass ceramic testing • Melter and off-gas testing with simulants • Test the mixing, sampling, and analyses • Canister testing • Decontamination system testing • Issue a requirements document • Issue a risk management document • Complete preliminary design • Integrated pilot testing • Issue a waste compliance plan A preliminary schedule and budget were developed to complete these activities as summarized in the following table (assuming 2012 dollars). TRL Budget Year MSA FMP GCF CCC CD Overall $M 2012 1 1 1 1 4 1 0.3 2013 2 2 1 1 4 1 1.3 2014 2 3 1 1 4 1 1.8 2015 2 3 2 2 4 2 2.6 2016 2 3 2 2 4 2 4.9 2017 2 3 3 2 4 2 9.8 2018 3 3 3 3 4 3 7.9 2019 3 3 3 3 4 3 5.1 2020 3 3 3 3 4 3 14.6 2021 3 3 3 3 4 3 7.3 2022 3 3 3 3 4 3 8.8 2023 4 4 4 4 4 4 9.1 2024 5 5 5 5 5 5 6.9 2025 6 6 6 6 6 6 6.9 CCC = canister cooling and crystallization; FMP = feeding, melting, and pouring; GCF = glass ceramic formulation; MSA = mixing, sampling, and analyses. This TMP is intended to guide the development of the glass ceramics waste form and process to the point where it is ready for industrialization.« less

Hypothermic general cold adaptation induced by local cold acclimation.

PubMed

Savourey, G; Barnavol, B; Caravel, J P; Feuerstein, C; Bittel, J H

1996-01-01

To study relationships between local cold adaptation of the lower limbs and general cold adaptation, eight subjects were submitted both to a cold foot test (CFT, 5 degrees C water immersion, 5 min) and to a whole-body standard cold air test (SCAT, 1 degree C, 2 h, nude at rest) before and after a local cold acclimation (LCA) of the lower limbs effected by repeated cold water immersions. The LCA induced a local cold adaptation confirmed by higher skin temperatures of the lower limbs during CFT and a hypothermic insulative general cold adaptation (decreased rectal temperature and mean skin temperature P < 0.05) without a change either in metabolic heat production or in lower limb skin temperatures during SCAT after LCA. It was concluded that local cold adaptation was related to the habituation process confirmed by decreased plasma concentrations of noradrenaline (NA) during LCA (P < 0.05). However, the hypothermic insulative general cold adaptation was unrelated either to local cold adaptation or to the habituation process, because an increased NA during SCAT after LCA (P < 0.05) was observed but was rather related to a "T3 polar syndrome" occurring during LCA.

Development of Hot and Cold Executive Function in Boys and Girls With ADHD.

PubMed

Skogli, Erik Winther; Andersen, Per Normann; Hovik, Kjell Tore; Øie, Merete

2017-02-01

To investigate the development of executive function with pronounced emotional salience (hot EF) and less pronounced emotional salience (cold EF) in boys and girls with ADHD relative to typically developing (TD) children. Seventy-five children with ADHD and 47 TD children were assessed with hot and cold EF tests at baseline and after 2 years. Despite considerable maturation, the ADHD group remained impaired on all cold EF tests relative to TD children after 2 years. There was no effect of gender on cold EF test results. Females with ADHD outperformed TD counterparts on hot EF at baseline. Females with ADHD showed deteriorating hot EF performance, while TD counterparts showed improved hot EF performance across time. Enduring cold EF impairments after 2 years may reflect stable phenotypic traits in children with ADHD. Results indicate divergent developmental trajectories of hot EF in girls with ADHD relative to TD counterparts.

Cold-end Subsystem Testing for the Fission Power System Technology Demonstration Unit

NASA Technical Reports Server (NTRS)

Briggs, Maxwell; Gibson, Marc; Ellis, David; Sanzi, James

2013-01-01

The Fission Power System (FPS) Technology Demonstration Unit (TDU) consists of a pumped sodium-potassium (NaK) loop that provides heat to a Stirling Power Conversion Unit (PCU), which converts some of that heat into electricity and rejects the waste heat to a pumped water loop. Each of the TDU subsystems is being tested independently prior to full system testing at the NASA Glenn Research Center. The pumped NaK loop is being tested at NASA Marshall Space Flight Center; the Stirling PCU and electrical controller are being tested by Sunpower Inc.; and the pumped water loop is being tested at Glenn. This paper describes cold-end subsystem setup and testing at Glenn. The TDU cold end has been assembled in Vacuum Facility 6 (VF 6) at Glenn, the same chamber that will be used for TDU testing. Cold-end testing in VF 6 will demonstrate functionality; validated cold-end fill, drain, and emergency backup systems; and generated pump performance and system pressure drop data used to validate models. In addition, a low-cost proof-of concept radiator has been built and tested at Glenn, validating the design and demonstrating the feasibility of using low-cost metal radiators as an alternative to high-cost composite radiators in an end-to-end TDU test.

Development and Analysis of Cold Trap for Use in Fission Surface Power-Primary Test Circuit

NASA Technical Reports Server (NTRS)

Wolfe, T. M.; Dervan, C. A.; Pearson, J. B.; Godfroy, T. J.

2012-01-01

The design and analysis of a cold trap proposed for use in the purification of circulated eutectic sodium potassium (NaK-78) loops is presented. The cold trap is designed to be incorporated into the Fission Surface Power-Primary Test Circuit (FSP-PTC), which incorporates a pumped NaK loop to simulate in-space nuclear reactor-based technology using non-nuclear test methodology as developed by the Early Flight Fission-Test Facility. The FSP-PTC provides a test circuit for the development of fission surface power technology. This system operates at temperatures that would be similar to those found in a reactor (500-800 K). By dropping the operating temperature of a specified percentage of NaK flow through a bypass containing a forced circulation cold trap, the NaK purity level can be increased by precipitating oxides from the NaK and capturing them within the cold trap. This would prevent recirculation of these oxides back through the system, which may help prevent corrosion.

Tested Demonstrations: Paramagnetism and Color of Liquid Oxygen: A Lecture Demonstration.

ERIC Educational Resources Information Center

Shakhashiri, Bassam Z.; And Others

1980-01-01

Presents materials and procedures for a lecture demonstration in which liquid nitrogen or liquid oxygen is poured between the poles of a powerful magnet. Hazards of these procedures are included in the discussion. (CS)

Predictive values of thermal and electrical dental pulp tests: a clinical study.

PubMed

Villa-Chávez, Carlos E; Patiño-Marín, Nuria; Loyola-Rodríguez, Juan P; Zavala-Alonso, Norma V; Martínez-Castañón, Gabriel A; Medina-Solís, Carlo E

2013-08-01

For a diagnostic test to be useful, it is necessary to determine the probability that the test will provide the correct diagnosis. Therefore, it is necessary to calculate the predictive value of diagnostics. The aim of the present study was to identify the sensitivity, specificity, positive and negative predictive values, accuracy, and reproducibility of thermal and electrical tests of pulp sensitivity. The thermal tests studied were the 1, 1, 1, 2-tetrafluoroethane (cold) and hot gutta-percha (hot) tests. For the electrical test, the Analytic Technology Pulp Tester (Analytic Technology, Redmond, WA) was used. A total of 110 teeth were tested: 60 teeth with vital pulp and 50 teeth with necrotic pulps (disease prevalence of 45%). The ideal standard was established by direct pulp inspection. The sensitivities of the diagnostic tests were 0.88 for the cold test, 0.86 for the heat test, and 0.76 for the electrical test, and the specificity was 1.0 for all 3 tests. The negative predictive value was 0.90 for the cold test, 0.89 for the heat test, and 0.83 for the electrical test, and the positive predictive value was 1.0 for all 3 tests. The highest accuracy (0.94) and reproducibility (0.88) were observed for the cold test. The cold test was the most accurate method for diagnostic testing. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Traveling-Wave Tube Cold-Test Circuit Optimization Using CST MICROWAVE STUDIO

NASA Technical Reports Server (NTRS)

Chevalier, Christine T.; Kory, Carol L.; Wilson, Jeffrey D.; Wintucky, Edwin G.; Dayton, James A., Jr.

2003-01-01

The internal optimizer of CST MICROWAVE STUDIO (MWS) was used along with an application-specific Visual Basic for Applications (VBA) script to develop a method to optimize traveling-wave tube (TWT) cold-test circuit performance. The optimization procedure allows simultaneous optimization of circuit specifications including on-axis interaction impedance, bandwidth or geometric limitations. The application of Microwave Studio to TWT cold-test circuit optimization is described.

40 CFR 600.107-08 - Fuel specifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Exhaust Emission Test Procedures § 600.107-08 Fuel specifications. (a) The test fuel specifications for... given in paragraph (b) of this section. (b)(1) Diesel test fuel used for cold temperature FTP testing... alternative fuel for cold temperature FTP testing. (c) Test fuels representing fuel types for which there are...

40 CFR 600.107-08 - Fuel specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Exhaust Emission Test Procedures § 600.107-08 Fuel specifications. (a) The test fuel specifications for... given in paragraph (b) of this section. (b)(1) Diesel test fuel used for cold temperature FTP testing... alternative fuel for cold temperature FTP testing. (c) Test fuels representing fuel types for which there are...

40 CFR 600.107-08 - Fuel specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Exhaust Emission Test Procedures § 600.107-08 Fuel specifications. (a) The test fuel specifications for... given in paragraph (b) of this section. (b)(1) Diesel test fuel used for cold temperature FTP testing... alternative fuel for cold temperature FTP testing. (c) Test fuels representing fuel types for which there are...

Immersion in Cold-Water Evaluation (ICE) and self-reported cold intolerance are reliable but unrelated measures.

PubMed

Traynor, Robyn; MacDermid, Joy C

2008-09-01

Intolerance to the cold is common following peripheral nerve injury and surgery of the upper extremity. Despite its prevalence, the exact pathophysiology and natural history of this condition are not well understood. Subjective, self-report questionnaires have been created and validated as reliable measures of post-traumatic cold intolerance. The difficulty currently lies in assigning an objective measure to this predominantly subjective phenomenon. The present study evaluated the test-retest reliability of a proposed objective measure of cold intolerance, the Immersion in Cold-water Evaluation (ICE), and its correlation with subjective measures in healthy control subjects. Two age groups were also compared to investigate the effect of age on cold intolerance and temperature recovery. On two separate testing days, subjects completed three health-related questionnaires and submersed their dominant hands in cold water. The temperature of their second and fifth digits was monitored during recovery. Both the objective cold-provocation testing and the subjective self-report questionnaires were highly reliable albeit not significantly correlated. No significant temperature recovery trend was noted between the age groups. Post-traumatic cold intolerance is postulated to have both a vascular and neural etiology among other contributing causes. The protocol studied here was centered predominantly on the former etiology, examining peripheral blood flow and associated temperature recovery. This study established ICE as a reliable means to objectively measure cold response, supplementing information provided by previously validated self-report methods.

Testing of materials from the Minnesota Cold Regions pavement research test facility

DOT National Transportation Integrated Search

1996-09-01

The U.S. Army Cold Regions Research and Engineering Laboratory (CRREL) conducted various laboratory tests on pavement materials from the Mn/ ROAD facility. The tests helped to characterize the behavior of materials under season frost conditions, and ...

Detection de la fin de la compaction des anodes par le son

NASA Astrophysics Data System (ADS)

Sanogo, Bazoumana

L'objectif de ce projet etait de developper un outil de controle en temps reel du temps de compaction en se servant du son genere par le vibrocompacteur pendant le formage des anodes crues. Ainsi, une application a ete developpee pour l'analyse des sons enregistres. Des essais ont ete realises avec differents microphones pour une meilleure qualite des mesures et un a ete choisi pour la suite du projet. De meme, differents tests ont ete realises sur des anodes de laboratoire ainsi que des anodes a l'echelle industrielle afin de mettre en place une methode pour la detection du temps optimal necessaire au formage des anodes. Les travaux au laboratoire de carbone a l'Universite du Quebec a Chicoutimi (UQAC) ont consiste a l'enregistrement de son des anodes fabriquees sur place avec differentes configurations; et a la caracterisation de certaines anodes de l'usine. Les anodes fabriquees au laboratoire sont reparties en deux groupes. Le premier regroupe les anodes pour la validation de notre methode. Ce sont des anodes produites avec des temps de compaction differents. Le laboratoire de carbone a l'UQAC est unique et il est possible de produire des anodes avec les memes proprietes que celles des anodes industrielles. Par consequent, la validation initialement prevue a l'usine a ete effectuee avec les anodes de laboratoire. Le deuxieme groupe a servi a etudier les effets des matieres premieres sur le temps de compaction. Le type de coke et le type de brai ont constitue les differentes variations dans ce deuxieme groupe. Quant aux tests et mesures a l'usine, ils ont ete realises en trois campagnes de mesure. La premiere campagne en juin 2014 a servi a standardiser et a trouver le meilleur positionnement des appareils pour les mesures, a regler le logiciel et a faire les premieres mesures. Une deuxieme campagne en mai 2015 a fait l'objet d'enregistrement de son en classant les anodes selon differents temps de compaction. La troisieme et derniere campagne en decembre 2015 a ete le lieu de tests finaux a l'usine en fabriquant des anodes avec differents criteres (variation du temps de compaction, taux de brai, arret manuel du compacteur, variation de la pression des ballons du haut du compacteur). Ces anodes ont ete ensuite analysees au laboratoire a l'UQAC. En parallele a ces travaux precites, l'amelioration de l'application d'analyse du son a ete faite avec le choix des parametres d'analyse et leur standardisation. Les resultats des premiers tests au laboratoire et ceux de la campagne de juin 2014 ont montre que la formation des anodes se fait suivant trois etapes : rearrangement des particules et du brai, compaction et consolidation et enfin la finition. Ces travaux ont montre en outre que le temps de compaction joue un role tres important dans la definition des proprietes finales des anodes. Ainsi, en plus du type de brai, du taux de brai et du type de coke, il faut tenir compte du temps de sur-compaction et de sous-compaction. En effet, ceci a ete demontre a travers les deux validations qui ont ete realisees. Les resultats de la caracterisation des echantillons (venant des anodes de la campagne de decembre 2015) ont montre qu'une anode compactee a un temps optimal acquiert une bonne resistance a la compression et sa resistivite electrique baisse. En outre, on note que le temps de compaction dans notre cas a baisse legerement avec l'augmentation de la pression des ballons de haut du vibrocompacteur. Ce qui a eu pour effet d'augmenter la densite crue de l'anode. Toutefois, il faut s'abstenir de generaliser ce constat car le nombre d'anodes testees est faible dans notre cas. Par ailleurs, cette etude montre que le temps necessaire pour le formage d'une anode croit avec l'augmentation du taux de brai et baisse legerement avec l'augmentation de la pression des ballons. (Abstract shortened by ProQuest.).

Repeatability of a cold stress test to assess cold sensitization.

PubMed

House, C M; Taylor, R J; Oakley, E H N

2015-10-01

Non-freezing cold injury (NFCI) is a syndrome in which damage to peripheral tissues occurs without the tissues freezing following exposure to low ambient temperatures. To assess the test-retest reliability of a cold stress test (CST) used to assess cold sensitization. Volunteers with no self-reported history of NFCI undertook the CST on three occasions. Thermal images were taken of the foot and hand before, immediately after and 5min after immersion of the limb in cold water for 2min. Cold sensitization was graded by the two clinicians and the lead author. Spot temperatures from the toe and finger pads were recorded. There were 30 white and 19 black male participants. The ratings indicated substantial agreement [a Cohen's kappa (κ) value of 0.61-0.8] to within ± one grading category for the hands and feet of the white volunteers and the hands of the black volunteers. Limits of agreement (LoA) analysis for toe and finger pad temperatures indicated high agreement (absolute 95% LoA < 5.5°C). Test-retest reliability for the feet of the black volunteers was not supported by the gradings (κ = 0.38) and toe pad temperatures (absolute 95% LoA = 9.5°C and coefficient of variation = 11%). The test-retest reliability of the CST is considered adequate for the assessment of the cold sensitization of the hands and feet of white and the hands of black healthy non-patients. The study should be repeated with patients who have suffered a NFCI. © Crown copyright 2015.

Selection of Environmentally Friendly Solvents for the Extravehicular Mobility Unit Secondary Oxygen Pack Cold Trap Testing

NASA Technical Reports Server (NTRS)

Steele, John; Chullen, Cinda; Morenz, Jesse; Stephenson, Curtis

2010-01-01

Freon-113(TradeMark) has been used as a chemistry lab sampling solvent at NASA/JSC for EMU (extravehicular Mobility Unit) SOP (Secondary Oxygen Pack) oxygen testing Cold Traps utilized at the USA (United Space Alliance) Houston facility. Similar testing has occurred at the HSWL (Hamilton Sundstrand Windsor Locks) facility. A NASA Executive Order bans the procurement of all ODS (ozone depleting substances), including Freon-113 by the end of 2009. In order to comply with NASA direction, HSWL began evaluating viable solvents to replace Freon-113 . The study and testing effort to find Freon-113 replacements used for Cold Trap sampling is the subject of this paper. Test results have shown HFE-7100 (a 3M fluorinated ether) to be an adequate replacement for Freon-113 as a solvent to remove and measure the non-volatile residue collected in a Cold Trap during oxygen testing. Furthermore, S-316 (a Horiba Instruments Inc. high molecular weight, non-ODS chlorofluorocarbon) was found to be an adequate replacement for Freon-113 as a solvent to reconstitute non-volatile residue removed from a Cold Trap during oxygen testing for subsequent HC (hydrocarbon) analysis via FTIR (Fourier Transform Infrared Spectroscopy).

40 CFR 86.1343-88 - Calculations; particulate exhaust emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... cold-start test, grams. (3) PH = Mass particulate measured during the hot-start test, grams. (4) BHP-hr..., grams per test phase. (PH = Pmass for the hot-start test and PC = Pmass for the cold-start test. (2... Exhaust Test Procedures § 86.1343-88 Calculations; particulate exhaust emissions. (a) The final reported...

40 CFR 86.1343-88 - Calculations; particulate exhaust emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... cold-start test, grams. (3) PH = Mass particulate measured during the hot-start test, grams. (4) BHP-hr..., grams per test phase. (PH = Pmass for the hot-start test and PC = Pmass for the cold-start test. (2... Exhaust Test Procedures § 86.1343-88 Calculations; particulate exhaust emissions. (a) The final reported...

INTERIOR VIEW, LOOKING WEST, WITH CRANE OPERATOR, TED SEALS, POURING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, LOOKING WEST, WITH CRANE OPERATOR, TED SEALS, POURING MOLTEN METAL INTO A 1,300 TON ELECTRIC HOLDING FURNACE OR MIXER. AN ELECTRONIC SCALE RECORDED THAT 50.5 TONS OF METAL WERE POURED INTO THE FURNACE DURING THIS POUR. - American Cast Iron Pipe Company, Mixer Building, 1501 Thirty-first Avenue North, Birmingham, Jefferson County, AL

Cold Antimatter Plasmas, and Aspirations for Cold Antihydrogen

DTIC Science & Technology

2002-06-24

comparison of any baryon and antibaryon by almost a factor of CP606, Non-Neutral Plasma Physics IV, edited by F. Anderegg et al. © 2002 American...antiprotons 3 _one-electron .1 eV quantum cyclotron 0.001 K FIGURE 1. Particle energies a million. An improved baryon CPT test (e.g. involving cold...more precise tests of CPT invariance with baryons and leptons than have been realized so far. The pursuit of cold antihydrogen thus began some time ago

Effects of Cold Temperature and Ethanol Content on VOC Emissions from Light-Duty Gasoline Vehicles.

PubMed

George, Ingrid J; Hays, Michael D; Herrington, Jason S; Preston, William; Snow, Richard; Faircloth, James; George, Barbara Jane; Long, Thomas; Baldauf, Richard W

2015-11-03

Emissions of speciated volatile organic compounds (VOCs), including mobile source air toxics (MSATs), were measured in vehicle exhaust from three light-duty spark ignition vehicles operating on summer and winter grade gasoline (E0) and ethanol blended (E10 and E85) fuels. Vehicle testing was conducted using a three-phase LA92 driving cycle in a temperature-controlled chassis dynamometer at two ambient temperatures (-7 and 24 °C). The cold start driving phase and cold ambient temperature increased VOC and MSAT emissions up to several orders of magnitude compared to emissions during other vehicle operation phases and warm ambient temperature testing, respectively. As a result, calculated ozone formation potentials (OFPs) were 7 to 21 times greater for the cold starts during cold temperature tests than comparable warm temperature tests. The use of E85 fuel generally led to substantial reductions in hydrocarbons and increases in oxygenates such as ethanol and acetaldehyde compared to E0 and E10 fuels. However, at the same ambient temperature, the VOC emissions from the E0 and E10 fuels and OFPs from all fuels were not significantly different. Cold temperature effects on cold start MSAT emissions varied by individual MSAT compound, but were consistent over a range of modern spark ignition vehicles.

Cold adaptation increases rates of nutrient flow and metabolic plasticity during cold exposure in Drosophila melanogaster

PubMed Central

McCue, Marshall D.; Sunny, Nishanth E.; Szejner-Sigal, Andre; Morgan, Theodore J.; Allison, David B.; Hahn, Daniel A.

2016-01-01

Metabolic flexibility is an important component of adaptation to stressful environments, including thermal stress and latitudinal adaptation. A long history of population genetic studies suggest that selection on core metabolic enzymes may shape life histories by altering metabolic flux. However, the direct relationship between selection on thermal stress hardiness and metabolic flux has not previously been tested. We investigated flexibility of nutrient catabolism during cold stress in Drosophila melanogaster artificially selected for fast or slow recovery from chill coma (i.e. cold-hardy or -susceptible), specifically testing the hypothesis that stress adaptation increases metabolic turnover. Using 13C-labelled glucose, we first showed that cold-hardy flies more rapidly incorporate ingested carbon into amino acids and newly synthesized glucose, permitting rapid synthesis of proline, a compound shown elsewhere to improve survival of cold stress. Second, using glucose and leucine tracers we showed that cold-hardy flies had higher oxidation rates than cold-susceptible flies before cold exposure, similar oxidation rates during cold exposure, and returned to higher oxidation rates during recovery. Additionally, cold-hardy flies transferred compounds among body pools more rapidly during cold exposure and recovery. Increased metabolic turnover may allow cold-adapted flies to better prepare for, resist and repair/tolerate cold damage. This work illustrates for the first time differences in nutrient fluxes associated with cold adaptation, suggesting that metabolic costs associated with cold hardiness could invoke resource-based trade-offs that shape life histories. PMID:27605506

Un Test contrastif oral pour l'evaluation des difficultes lexicales dans l'apprentissage de l'anglais L2 (An Oral Contrastive Test for the Evaluation of Lexical Difficulties in Learning English as a Second Language).

ERIC Educational Resources Information Center

Haeusser, Christiane

1978-01-01

The test described here is a particular type of diagnostic test; it is part of a series of tests designed to explore systematically areas of potential lexical difficulty in the English language for French-speaking students of English. The lexical units are considered under their formal, morphological, syntactic and semantic aspects. The test has…

Cooling During Exercise: An Overlooked Strategy for Enhancing Endurance Performance in the Heat.

PubMed

Stevens, Christopher J; Taylor, Lee; Dascombe, Ben J

2017-05-01

It is well established that endurance performance is negatively affected by environmental heat stress due to a complex interaction of physical, physiological and psychological alterations. Numerous scientific investigations have attempted to improve performance in the heat with pre-cooling (cooling prior to an exercise test), and as such this has become a well-established ergogenic practice for endurance athletes. However, the use of mid-cooling (cooling during an exercise test) has received considerably less research attention in comparison, despite recent evidence to suggest that the advantage gained from mid-cooling may outweigh that of pre-cooling. A range of mid-cooling strategies are beneficial for endurance performance in the heat, including the ingestion of cold fluids and ice slurry, both with and without menthol, as well as cooling of the neck and face region via a cooling collar or water poured on the head and face. The combination of pre-cooling and mid-cooling has also been effective, but few comparisons exist between the timing and type of such interventions. Therefore, athletes should experiment with a range of suitable mid-cooling strategies for their event during mock competition scenarios, with the aim to determine their individual tolerable limits and performance benefits. Based on current evidence, the effect of mid-cooling on core temperature appears largely irrelevant to any subsequent performance improvements, while cardiovascular, skin temperature, central nervous system function and psychophysiological factors are likely involved. Research is lacking on elite athletes, and as such it is currently unclear how this population may benefit from mid-cooling.

A simple and specific high performance liquid chromatography method for the assay of a series of novel dermal penetration enhancers.

PubMed

Michniak, B B; Seyda, K L

1993-02-01

Synopsis A series of clofibric acid amides has been synthesized and previously reported by the authors as possessing enhancer activity in vitro in athymic nude mouse skin against model drugs, hydrocortisone-21-acetate and beta-methasone-17-valerate. An assay was required for each of these enhancers however, which would be specific for each compound and would also separate model drugs and their metabolite peaks. This study reports reverse phase high performance liquid chromatography assays for clofibric acid amide and seven derivatives (Ia-Ig). All enhancers showed maximum absorption at 232 nm, betamethasone (BM) and its valerate (BMV) at 238 nm, and hydrocortisone (HC) and its acetate (HCA) at 242 nm. Practical units of detection for the amides were 0.46-2.8 mug ml(-1) and peaks were sharp and well-separated from steroid peaks in three vehicles - methanol alone. Franz diffusion cell receptor phase samples (isotonic phosphate buffer), and full-thickness athymic nude mouse skin extracts in methanol. Mobile phases consisted of various proportions of acetonitrile and water, some with 2-propanol. The octyl amide for example, with mobile phase CH(3)CN: H(2)O (85:15) at 1 ml min(-1) had a retention time (t(R)) of 7.9 mins. Under the same conditions, retention times for the steroids were HC, t(R)= 3.3 mins; HCA, t(R)= 4.3 mins; BM, t(R)= 3.4 mins; BMV, t(R)= 4.6 mins. Résumé Les auteurs avaient démontré dans un article précédent le pouvoir accélérateur de pénétration dermique in vitro d'une gamme d'amides d'acide clofibrique sur la peau de souris sans poils, et sans thymus avec des médicaments types tels que l'acetate 21 d'hydrocortisone et le valerate 17 de beta-metasone. Il a cependant été requis, pour chacun de ces accélérateurs, un test spécifique pour chaque composition, permettant de séparer chaque médicament et les pics des métabolites. Cette étude décrit des tests par chromatographie liquide à haute performance en phase inverse pour l'acide chlofibrique et 7 dérivés (Ia-Ig). Tous les accélérateurs ont montré une absorption maximale à 232 nm, la beta-metasone (BM) et son valerate (BMV) à 238 nm, l'hydrocortisone (HC) et son acetate (HCA) à 242 nm. Les unités de détection s'élevaient à 0.46-2.8 mug ml(-1) pour les amides et les pics étaient aigus et distincts des pics stéroïdes et se composaient de 3 véhicules - le méthanol seul, des échantillons du récepteur de cellule de diffusion Franz (tampon du phosphate isotonique) et des extraits de peau de souris sans thymus dans du méthanol. Les phases mobiles étaient constituées de différentes proportions d'acetonitrile et d'eau, certaines avec du propanol-2. L'amide octyl par exemple, avec une phase mobile CH(3)CN: H(2)O (85:15) à 1 ml min(-1) avait un temps de rétention (t(R)) de 7.9 min. Dans des conditions identiques, les temps de rétention pour les stéroïdes étaient les suivants: pour HC, t(R)= 3.3 mins; pour HCA, t(R)= 4.3 mins; pour BM: t(R)= 3.4 mins; pour BMV: t(R)= 4.6 mins.

Impact of cold climates on vehicle emissions: the cold start air toxics pulse : final report.

DOT National Transportation Integrated Search

2016-09-21

This project measured cold start emissions from four vehicles in winter using fast response instrumentation to accurately measure the : time variation of the cold start emission pulse. Seventeen successful tests were conducted over a temperature rang...

The effect of ethnicity on the vascular responses to cold exposure of the extremities.

PubMed

Maley, Matthew J; Eglin, Clare M; House, James R; Tipton, Michael J

2014-11-01

Cold injuries are more prevalent in individuals of African descent (AFD). Therefore, we investigated the effect of extremity cooling on skin blood flow (SkBF) and temperature (T sk) between ethnic groups. Thirty males [10 Caucasian (CAU), 10 Asian (ASN), 10 AFD] undertook three tests in 30 °C air whilst digit T sk and SkBF were measured: (i) vasomotor threshold (VT) test--arm immersed in 35 °C water progressively cooled to 10 °C and rewarmed to 35 °C to identify vasoconstriction and vasodilatation; (ii) cold-induced vasodilatation (CIVD) test--hand immersed in 8 °C water for 30 min followed by spontaneous warming; (iii) cold sensitivity (CS) test--foot immersed in 15 °C water for 2 min followed by spontaneous warming. Cold sensory thresholds of the forearm and finger were also assessed. In the VT test, vasoconstriction and vasodilatation occurred at a warmer finger T sk in AFD during cooling [21.2 (4.4) vs. 17.0 (3.1) °C, P = 0.034] and warming [22.0 (7.9) vs. 12.1 (4.1) °C, P = 0.002] compared with CAU. In the CIVD test, average SkBF during immersion was greater in CAU [42 (24) %] than ASN [25 (8) %, P = 0.036] and AFD [24 (13) %, P = 0.023]. Following immersion, SkBF was higher and rewarming faster in CAU [3.2 (0.4) °C min(-1)] compared with AFD [2.5 (0.7) °C min(-1), P = 0.037], but neither group differed from ASN [3.0 (0.6) °C min(-1)]. Responses to the CS test and cold sensory thresholds were similar between groups. AFD experienced a more intense protracted finger vasoconstriction than CAU during hand immersion, whilst ASN experienced an intermediate response. This greater sensitivity to cold may explain why AFD are more susceptible to cold injuries.

Gas-Centered Swirl Coaxial Liquid Injector Evaluations

NASA Technical Reports Server (NTRS)

Cohn, A. K.; Strakey, P. A.; Talley, D. G.

2005-01-01

Development of Liquid Rocket Engines is expensive. Extensive testing at large scales usually required. In order to verify engine lifetime, large number of tests required. Limited Resources available for development. Sub-scale cold-flow and hot-fire testing is extremely cost effective. Could be a necessary (but not sufficient) condition for long engine lifetime. Reduces overall costs and risk of large scale testing. Goal: Determine knowledge that can be gained from sub-scale cold-flow and hot-fire evaluations of LRE injectors. Determine relationships between cold-flow and hot-fire data.

Cold adaptation, aging, and Korean women divers haenyeo.

PubMed

Lee, Joo-Young; Park, Joonhee; Kim, Siyeon

2017-08-08

We have been studying the thermoregulatory responses of Korean breath-hold women divers, called haenyeo, in terms of aging and cold adaptation. During the 1960s to the 1980s, haenyeos received attention from environmental physiologists due to their unique ability to endure cold water while wearing only a thin cotton bathing suit. However, their overall cold-adaptive traits have disappeared since they began to wear wetsuits and research has waned since the 1980s. For social and economic reasons, the number of haenyeos rapidly decreased to 4005 in 2015 from 14,143 in 1970 and the average age of haenyeos is about 75 years old at present. For the past several years, we revisited and explored older haenyeos in terms of environmental physiology, beginning with questionnaire and field studies and later advancing to thermal tolerance tests in conjunction with cutaneous thermal threshold tests in a climate chamber. As control group counterparts, older non-diving females and young non-diving females were compared with older haenyeos in the controlled experiments. Our findings were that older haenyeos still retain local cold tolerance on the extremities despite their aging. Finger cold tests supported more superior local cold tolerance for older haenyeos than for older non-diving females. However, thermal perception in cold reflected aging effects rather than local cold acclimatization. An interesting finding was the possibility of positive cross-adaptation which might be supported by greater heat tolerance and cutaneous warm perception thresholds of older haenyeos who adapted to cold water. It was known that cold-adaptive traits of haenyeos disappeared, but we confirmed that cold-adaptive traits are still retained on the face and hands which could be interpreted by a mode switch to local adaptation from the overall adaptation to cold. Further studies on cross-adaptation between chronic cold stress and heat tolerance are needed.

Low Phase Noise Fiber Optics Links for Space Applications

DTIC Science & Technology

2005-07-13

photo- oscillateur intégré pour 17 dB de pertes optiques Liaison active à 874,2 MHz avec photo- oscillateur intégré pour 18 dB de pertes optiques Liaison...active à 874,2 MHz avec photo- oscillateur intégré pour 20 dB de pertes optiques Liaison active à 874,2 MHz avec photo- oscillateur intégré pour 23 dB...de pertes optiques Liaison active à 874,2 MHz avec photo- oscillateur intégré pour 25 dB de pertes optiques Liaison active à 874,2 MHz avec photo

40 CFR 86.208-94 - Dynamometer.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Passenger Vehicles; Cold Temperature Test Procedures § 86.208-94 Dynamometer. (a) For testing that is... the manufacturer, a dynamometer with different characteristics may be used provided cold CO emissions...

40 CFR 86.208-94 - Dynamometer.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Passenger Vehicles; Cold Temperature Test Procedures § 86.208-94 Dynamometer. (a) For testing that is... the manufacturer, a dynamometer with different characteristics may be used provided cold CO emissions...

40 CFR 86.208-94 - Dynamometer.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Passenger Vehicles; Cold Temperature Test Procedures § 86.208-94 Dynamometer. (a) For testing that is... the manufacturer, a dynamometer with different characteristics may be used provided cold CO emissions...

Developpement d'un montage simulant l'erosion par la pluie pour l'evaluation des revetements glaciophobes dans le domaine aerospatial

NASA Astrophysics Data System (ADS)

Tremblay, Sarah-Eve

Ce memoire presente le developpement d’un montage simulant l’erosion par la pluie afin d’effectuer l’evaluation de differents revetements glaciophobes dans le domaine aerospatial. Bien que plusieurs revetements presentent une bonne efficacite a reduire l’adherence et/ou l’accumulation de glace, ils ne repondent pas necessairement aux normes de resistance a l’erosion simulee par les gouttes de pluie les frappant a grande vitesse. Il n’existe qu’une installation en Amerique du Nord offrant un service d’essai qui evalue la resistance a l’erosion par la pluie suivant les normes aerospatiales. Etant l’unique institution pouvant faire la certification de peintures utilisees sur les avions en ce qui a trait a l’erosion par la pluie, ce service est donc difficile d’acces et couteux. Le laboratoire international des materiaux antigivre (LIMA) a developpe un essai plus rapide et moins couteux, facilitant ainsi le developpement de revetements glaciophobes devant resister a l’erosion par la pluie. Dans cette etude, le developpement du montage d’erosion par la pluie effectue au laboratoire des materiaux antigivre (LIMA) est presente. En particulier, des essais sur quatre (4) revetements dont la resistance a l’erosion est connue, et sur trois revetements industriels, ont ete effectues afin d’ajuster les differents parametres du montage comme la pression et la temperature de l’eau ainsi que la robustesse du montage. Ensuite, des essais de sensibilite et de reproductibilite des resultats ont egalement ete effectues pour fin de validation du montage et du protocole experimental. Pour ce faire, le montage de type jet d’eau developpe consiste principalement en une pompe a haute pression qui projette un jet d’eau continu passant par les orifices d’un disque tournant. Cette operation permet de generer une goutte de pluie simulee qui est projetee sur un echantillon de revetement statique. L’essai est base sur la norme standard ASTM (Liquid Impingement Erosion Testing, G73-82). La resistance a l’erosion du materiau est determinee a l’aide du nombre d’impacts subi par l’echantillon obtenu avant la production de dommages visibles. Donc, pour determiner le niveau d’erosion, quatre sites d’impacts doivent etre erodes sur cinq sur le meme rang pour le meme nombre d’impact. L’analyse des quatre revetements de resistance a l’erosion connus a ete completee par l’examen microscopique de chaque site d’impact et d’une photo. Le choix des quatre revetements de resistance a l’erosion connue, allant du plus resistant au moins resistant, a permis de verifier que le montage etait assez sensible pour evaluer les revetements souvent utilises dans le domaine aerospatial. De plus, l’evaluation des trois revetements industriels a permis, pour sa part, de confirmer les resultats obtenus precedemment. Finalement, pour evaluer la sensibilite et la reproductibilite des resultats, de deux a six repetitions pour chaque revetement a ete effectuees donnant des taux d’erosion allant de 100 a 100 000 impacts. L’intervalle des ecarts-types varie de ± 0% a ± 47% pour une moyenne de ± 17%. Le critere d’echec a ete determine a l’aide du nombre d’impacts avant l’apparition de dommage visible ainsi que de la repetabilite des resultats.

LADEE Propulsion System Cold Flow Test

NASA Technical Reports Server (NTRS)

Williams, Jonathan Hunter; Chapman, Jack M.; Trinh, Hau, P.; Bell, James H.

2013-01-01

Lunar Atmosphere and Dust Environment Explorer (LADEE) is a NASA mission that will orbit the Moon. Its main objective is to characterize the atmosphere and lunar dust environment. The spacecraft development is being led by NASA Ames Research Center and scheduled for launch in 2013. The LADEE spacecraft will be operated with a bi-propellant hypergolic propulsion system using MMH and NTO as the fuel and oxidizer, respectively. The propulsion system utilizes flight-proven hardware on major components. The propulsion layout is composed of one 100-lbf main thruster and four 5-lbf RCS thrusters. The propellants are stored in four tanks (two parallel-connected tanks per propellant component). The propellants will be pressurized by regulated helium. A simulated propulsion system has been built for conducting cold flow test series to characterize the transient fluid flow of the propulsion system feed lines and to verify the critical operation modes, such as system priming, waterhammer, and crucial mission duty cycles. Propellant drainage differential between propellant tanks will also be assessed. Since the oxidizer feed line system has a higher flow demand than the fuel system does, the cold flow test focuses on the oxidizer system. The objective of the cold flow test is to simulate the LADEE propulsion fluid flow operation through water cold flow test and to obtain data for anchoring analytical models. The models will be used to predict the transient and steady state flow behaviors in the actual flight operations. The test activities, including the simulated propulsion test article, cold flow test, and analytical modeling, are being performed at NASA Marshall Space Flight Center. At the time of the abstract submission, the test article checkout is being performed. The test series will be completed by November, 2012

Une nouvelle théorie de la cinétique des réactions radical-radical

NASA Astrophysics Data System (ADS)

Green, N. J. B.; Rickerby, A. G.

1999-01-01

Radical recombination reactions are of central importance in radiation chemistry. In general such reactions are slower than diffusion-controlled because of the radical spins. The rate constant is corrected by a multiplicative spin statistical factor, which represents the probability that the radicals encounter one another in a reactive state. However, this method does not account for the possibility that the reactivity of a pair may recover following an unreactive encounter, for example by spin relaxation or by a coherent evolution of the spin function. In this paper we show how the spin statistical factor can be corrected for the recovery of reactivity. The new theory covers a large range of mechanisms for the recovery of reactivity, and gives simple analytical results. Both steady-state and transient solutions are presented and the former are tested against experiment for the reaction between the hydrated electron and oxygen, and for the magnetic field effect on the rate constant of an elementary reaction. Les réactions de recombinaison entre deux radicaux libres ont une grande importance en chimie sous rayonnement. En général, du fait du spin des radicaux, de telles réactions sont moins rapides que celles qui sont contrôlées par la diffusion. Les constantes de vitesse sont corrigées par un facteur multiplicatif, le facteur statistique de spin, qui représente la probabilité pour que les radicaux se rencontrent, l'un avec l'autre, dans un état réactif. Cependant, cette méthode ne tient pas compte de la possibilité pour que la même paire se rencontre plusieurs fois en raison de rencontres non-réactives. Ensuite la réactivité de cette paire peut se rétablir par exemple par relaxation de spins, ou par évolution cohérente d'une superposition des états de spin. Dans cet article on démontre comment on peut corriger le facteur statistique de spin pour le rétablissement de la réactivité. La nouvelle théorie couvre un large domaine de mécanismes de rétablissement de la réactivité ; elle donne des résultats analytiques simples pour le facteur statistique modifié. On présente des solutions dans l'état stationnaire et des solutions transitoires; les premières sont testées pour la réaction entre l'électron hydraté et l'oxygène et également pour l'effet d'un champ magnétique sur la constante de vitesse d'une réaction élémentaire.

Comparison of the efficacy of a custom-made pulse oximeter probe with digital electric pulp tester, cold spray, and rubber cup for assessing pulp vitality.

PubMed

Dastmalchi, Nafiseh; Jafarzadeh, Hamid; Moradi, Saeed

2012-09-01

The ideal technique for the evaluation of pulp vitality should be noninvasive, painless, objective, reliable, and reproducible. To achieve this, the most routine tests are sensitivity tests. However, a major shortcoming with these tests is that they indirectly indicate pulp vitality by measuring a neural response. Pulse oximetry is a well-established oxygen saturation monitoring technique broadly used in medicine. However, its efficacy as the pulp vitality test should be evaluated. The aim of this study was to design and build a custom-made pulse oximeter dental probe and to evaluate its efficacy in comparison with electric pulp tester, cold spray, and a rubber cup in pulp vitality testing. Twenty-four single-canal mandibular premolars needing endodontic treatment were selected. The patients did not have systemic disease and did not consume drugs. Also, they had no clinically relevant signs of necrosis. The selected teeth were pulpally tested with 4 kinds of tests including pulse oximetry, the electric test, cold spray, and the rubber cup. After endodontic treatment of these teeth, which revealed the actual status of the pulp, the results were analyzed by the kappa test to show the efficacy of these tests. When comparing electric, cold, heat, and pulse oximeter tests with the gold standard, the kappa agreement coefficient was 18%, 18%, 14%, and 91%, respectively. The sensitivity of pulse oximetry, a rubber cup, electric test, and cold spray was 0.93, 0.60, 0.60, and 0.53, respectively. The specificity of these tests was 1.00, 0.55, 0.22, and 0.66, respectively. Pulp testing by using pulse oximetry is more reliable than the electric test, rubber cup, and cold spray. The custom-made pulse oximeter dental probe is an effective and objective method for pulp vitality assessment. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Insulation Test Cryostat with Lift Mechanism

NASA Technical Reports Server (NTRS)

Dokos, Adam G. (Inventor); Fesmire, James E. (Inventor)

2014-01-01

A multi-purpose, cylindrical thermal insulation test apparatus is used for testing insulation materials and systems of materials using a liquid boil-off calorimeter system for absolute measurement of the effective thermal conductivity (k-value) and heat flux of a specimen material at a fixed environmental condition (cold-side temperature, warm-side temperature, vacuum pressure level, and residual gas composition). The apparatus includes an inner vessel for receiving a liquid with a normal boiling point below ambient temperature, such as liquid nitrogen, enclosed within a vacuum chamber. A cold mass assembly, including the upper and lower guard chambers and a middle test vessel, is suspended from a lid of the vacuum canister. Each of the three chambers is filled and vented through a single feedthrough. All fluid and instrumentation feedthroughs are mounted and suspended from a top domed lid to allow easy removal of the cold mass. A lift mechanism allows manipulation of the cold mass assembly and insulation test article.

Insulation Test Cryostat with Lift Mechanism

NASA Technical Reports Server (NTRS)

Fesmire, James E. (Inventor); Dokos, Adam G. (Inventor)

2016-01-01

A multi-purpose, cylindrical thermal insulation test apparatus is used for testing insulation materials and systems of materials using a liquid boil-off calorimeter system for absolute measurement of the effective thermal conductivity (k-value) and heat flux of a specimen material at a fixed environmental condition (cold-side temperature, warm-side temperature, vacuum pressure level, and residual gas composition). An inner vessel receives liquid with a normal boiling point below ambient temperature, such as liquid nitrogen, enclosed within a vacuum chamber. A cold mass assembly, including upper and lower guard chambers and middle test vessel, is suspended from a lid of the vacuum canister. Each of the three chambers is filled and vented through a single feedthrough. All fluid and instrumentation feedthroughs are mounted and suspended from a top domed lid allowing easy removal of the cold mass. A lift mechanism allows manipulation of the cold mass assembly and insulation test article.

Do mitochondrial properties explain intraspecific variation in thermal tolerance?

PubMed

Fangue, Nann A; Richards, Jeffrey G; Schulte, Patricia M

2009-02-01

As global temperatures rise, there is a growing need to understand the physiological mechanisms that determine an organism's thermal niche. Here, we test the hypothesis that increases in mitochondrial capacity with cold acclimation and adaptation are associated with decreases in thermal tolerance using two subspecies of killifish (Fundulus heteroclitus) that differ in thermal niche. We assessed whole-organism metabolic rate, mitochondrial amount and mitochondrial function in killifish acclimated to several temperatures. Mitochondrial enzyme activities and mRNA levels were greater in fish from the northern subspecies, particularly in cold-acclimated fish, suggesting that the putatively cold-adapted northern subspecies has a greater capacity for increases in mitochondrial amount in response to cold acclimation. When tested at the fish's acclimation temperature, maximum ADP-stimulated (State III) rates of mitochondrial oxygen consumption in vitro were greater in cold-acclimated northern fish than in southern fish but did not differ between subspecies at higher acclimation temperatures. Whole-organism metabolic rate was greater in fish of the northern subspecies at all acclimation temperatures. Cold acclimation also changed the response of mitochondrial respiration to acute temperature challenge. Mitochondrial oxygen consumption was greater in cold-acclimated northern fish than in southern fish at low test temperatures, but the opposite was true at high test temperatures. These differences were reflected in whole-organism oxygen consumption. Our data indicate that the plasticity of mitochondrial function and amount differs between killifish subspecies, with the less high-temperature tolerant, and putatively cold adapted, northern subspecies having greater ability to increase mitochondrial capacity in the cold. However, there were few differences in mitochondrial properties between subspecies at warm acclimation temperatures, despite differences in both whole-organism oxygen consumption and thermal tolerance at these temperatures.

ETR, TRA642. ON BASEMENT FLOOR. REACTOR VESSEL WILL BE PLACED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR, TRA-642. ON BASEMENT FLOOR. REACTOR VESSEL WILL BE PLACED WITHIN THE INNER METAL FORM. WHEN CONCRETE IS POURED OUTSIDE THIS FORM, CONDUIT HOLES WILL BE PRESERVE SPACE THROUGH HOLES. INL NEGATIVE NO. 56-1507. Jack L. Anderson, Photographer, 5/8/1956 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Enzyme-Linked Immunosorbant Assays for Identification of Biological Agents in Sample Unknowns: NATO SIBCA. Exercise 5

DTIC Science & Technology

2004-12-01

avantage comme Brucella spp par ex. De plus, chaque ELISA d’agent devrait &tre test~e avec un agent vivant pour confirmer la sensibilit6 du biotest aux...materiaux vivants . A plus long terme, i1 serait souhaitable d𔄀tudier des solutions de rechange qui seraient plus sensibles aux techniques

Effects of Controlled Cooling-Induced Ferrite-Pearlite Microstructure on the Cold Forgeability of XC45 Steel

NASA Astrophysics Data System (ADS)

Hu, Chengliang; Chen, Lunqiang; Zhao, Zhen; Gong, Aijun; Shi, Weibing

2018-05-01

The combination of hot/warm and cold forging with an intermediate controlled cooling process is a promising approach to saving costs in the manufacture of automobile parts. In this work, the effects of the ferrite-pearlite microstructure, which formed after controlled cooling, on the cold forgeability of a medium-carbon steel were investigated. Different specimens for both normal and notched tensile tests were directly heated to high temperature and then cooled down at different cooling rates, producing different ferrite volume fractions, ranging from 6.69 to 40.53%, in the ferrite-pearlite microstructure. The yield strength, ultimate tensile strength, elongation rate, percentage reduction of area, and fracture strain were measured by tensile testing. The yield strength, indicating deformation resistance, and fracture strain, indicating formability, were used to evaluate the cold forgeability. As the ferrite volume fraction increased, the cold forgeability of the dual-phase ferritic-pearlitic steel improved. A quantitatively relationship between the ferrite volume fraction and the evaluation indexes of cold forgeability for XC45 steel was obtained from the test data. To validate the mathematical relationship, different tensile specimens machined from real hot-forged workpieces were tested. There was good agreement between the predicted and measured values. Our predictions from the relationship for cold forgeability had an absolute error less than 5%, which is acceptable for industrial applications and will help to guide the design of combined forging processes.

Cold adaptation shapes the robustness of metabolic networks in Drosophila melanogaster

PubMed Central

Williams, CM; Watanabe, M; Guarracino, MR; Ferraro, MB; Edison, AS; Morgan, TJ; Boroujerdi, AFB; Hahn, DA

2015-01-01

When ectotherms are exposed to low temperatures, they enter a cold-induced coma (chill coma) that prevents resource acquisition, mating, oviposition, and escape from predation. There is substantial variation in time taken to recover from chill coma both within and among species, and this variation is correlated with habitat temperatures such that insects from cold environments recover more quickly. This suggests an adaptive response, but the mechanisms underlying variation in recovery times are unknown, making it difficult to decisively test adaptive hypotheses. We use replicated lines of Drosophila melanogaster selected in the laboratory for fast (hardy) or slow (susceptible) chill-coma recovery times to investigate modifications to metabolic profiles associated with cold adaptation. We measured metabolite concentrations of flies before, during, and after cold exposure using NMR spectroscopy to test the hypotheses that hardy flies maintain metabolic homeostasis better during cold exposure and recovery, and that their metabolic networks are more robust to cold-induced perturbations. The metabolites of cold-hardy flies were less cold responsive and their metabolic networks during cold exposure were more robust, supporting our hypotheses. Metabolites involved in membrane lipid synthesis, tryptophan metabolism, oxidative stress, energy balance, and proline metabolism were altered by selection on cold tolerance. We discuss the potential significance of these alterations. PMID:25308124

40 CFR 86.1413 - Fuel specifications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Trucks; Certification Short Test Procedures § 86.1413 Fuel specifications. (a) The test fuel to be used... section. (b) CST test fuels by option. (1) Test Option 1: Use Cold CO fuel as specified in the table in § 86.213-94. (2) Test Option 2: Use Cold CO fuel, as specified in the table in § 86.213-94; optionally...

40 CFR 86.1413 - Fuel specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Trucks; Certification Short Test Procedures § 86.1413 Fuel specifications. (a) The test fuel to be used... section. (b) CST test fuels by option. (1) Test Option 1: Use Cold CO fuel as specified in the table in § 86.213-94. (2) Test Option 2: Use Cold CO fuel, as specified in the table in § 86.213-94; optionally...

40 CFR 86.1413 - Fuel specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Trucks; Certification Short Test Procedures § 86.1413 Fuel specifications. (a) The test fuel to be used... section. (b) CST test fuels by option. (1) Test Option 1: Use Cold CO fuel as specified in the table in § 86.213-94. (2) Test Option 2: Use Cold CO fuel, as specified in the table in § 86.213-94; optionally...

40 CFR 86.1413 - Fuel specifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Trucks; Certification Short Test Procedures § 86.1413 Fuel specifications. (a) The test fuel to be used... section. (b) CST test fuels by option. (1) Test Option 1: Use Cold CO fuel as specified in the table in § 86.213-94. (2) Test Option 2: Use Cold CO fuel, as specified in the table in § 86.213-94; optionally...

Patient-related risk factors for urinary retention following ambulatory general surgery: a systematic review and meta-analysis.

PubMed

Mason, Sam E; Scott, Alasdair J; Mayer, Erik; Purkayastha, Sanjay

2016-06-01

Postoperative urinary retention (POUR) is a source of avoidable patient harm. The aim of this review is to identify and quantify the role of patient-related risk factors in the development of POUR following ambulatory general surgery. Studies published until December 2014 were identified by searching MEDLINE, EMBASE, and PsycINFO databases. Risk factors assessed in 3 or more studies were meta-analyzed. Twenty-one studies were suitable for inclusion consisting of 7,802 patients. The incidence of POUR was 14%. Increased age and the presence of lower urinary tract symptoms significantly increased risk with odds ratios [ORs] of 2.11 (95% confidence interval [CI] 1.15 to 3.86) and 2.83 (1.57 to 5.08), respectively. Male sex was not associated with developing POUR (OR .96, 95% CI .62 to 1.50). Preoperative α-blocker use significantly decreased the incidence of POUR with an OR of .37 (95% CI .15 to .91). Increased age and the presence of lower urinary tract symptoms increase the risk of POUR, while α-blocker use confers protection. Male sex was not associated with POUR. These findings assist in preoperative identification of patients at high risk of POUR. Copyright © 2015 Elsevier Inc. All rights reserved.

2. COLD FLOW LABORATORY, VIEW TOWARDS NORTH. Glenn L. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. COLD FLOW LABORATORY, VIEW TOWARDS NORTH. - Glenn L. Martin Company, Titan Missile Test Facilities, Cold Flow Laboratory Building B, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

1. COLD FLOW LABORATORY, VIEW TOWARDS EAST. Glenn L. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. COLD FLOW LABORATORY, VIEW TOWARDS EAST. - Glenn L. Martin Company, Titan Missile Test Facilities, Cold Flow Laboratory Building B, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Alternative Submarine Watch Systems: Recommendation for a New CF Submarine Watch Schedule (Systemes Differents d’Horaire de Garde a Bord des Sous-Marins: Nouvel Horaire Recommande Pour les Sous-Marins des FC)

DTIC Science & Technology

2010-01-01

comparativement à une efficacité cognitive de 96 % pour l’horaire de 1 tour sur trois de quatre heures ainsi que pour l’horaire de 1 tour sur trois de...tour sur 2 (8-4-4-8) comparativement à une efficacité cognitive de 96 % pour l’horaire de 1 tour sur trois de quatre heures ainsi que pour l’horaire...FAST™ (Fatigue Avoidance and Safety Tool), a computer application designed to predict and prevent fatigue in operational settings. The output of FAST

Reactor Simulator Testing Overview

NASA Technical Reports Server (NTRS)

Schoenfeld, Michael P.

2013-01-01

OBJECTIVE: Integrated testing of the TDU components TESTING SUMMARY: a) Verify the operation of the core simulator, the instrumentation and control system, and the ground support gas and vacuum test equipment. b) Thermal test heat regeneration design aspect of a cold trap purification filter. c) Pump performance test at pump voltages up to 150 V (targeted mass flow rate of 1.75 kg/s was not obtained in the RxSim at the originally constrained voltage of 120 V). TESTING HIGHLIGHTS: a) Gas and vacuum ground support test equipment performed effectively for NaK fill, loop pressurization, and NaK drain operations. b) Instrumentation and control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings. c) Cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained which was lower than the predicted 750 K but 156 K higher than the cold temperature indicating the design provided some heat regeneration. d) ALIP produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz.

40 CFR 1066.701 - Applicability and general provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... POLLUTION CONTROLS VEHICLE-TESTING PROCEDURES Cold Temperature Test Procedures § 1066.701 Applicability and...) temperature range. (b) Do not apply the humidity correction factor in § 1066.615(a) for cold temperature...

Design and cold test of S-BAND cavity BPM for HLS

NASA Astrophysics Data System (ADS)

Luo, Qing; Sun, BaoGen; Jia, QiKa; He, DuoHui; Fang, Jia

2011-12-01

An S-band cavity BPM is designed for a new injector in National Synchrotron Radiation Laboratory. A re-entrant position cavity is tuned to the TM110 mode as position cavity. Cut-through waveguides are used as pickups to suppress the monopole signal. Theoretical resolution of this design is 31 nm. A prototype cavity BPM system is manufactured for off-line cold tests. The wire scanning method is used to calibrate the BPM and estimate the performance of the on-line BPM system. A cross-talk problem has been detected during the cold test. Racetrack cavity BPM design can be used to suppress the cross-talk. With the nonlinear effect being ignored, transform matrix can be used to correct cross-talk. Analysis of cold test results shows that the position resolution of prototype BPM is better than 3 μm.

Machine for Automatic Bacteriological Pour Plate Preparation

PubMed Central

Sharpe, A. N.; Biggs, D. R.; Oliver, R. J.

1972-01-01

A fully automatic system for preparing poured plates for bacteriological analyses has been constructed and tested. The machine can make decimal dilutions of bacterial suspensions, dispense measured amounts into petri dishes, add molten agar, mix the dish contents, and label the dishes with sample and dilution numbers at the rate of 2,000 dishes per 8-hr day. In addition, the machine can be programmed to select different media so that plates for different types of bacteriological analysis may be made automatically from the same sample. The machine uses only the components of the media and sterile polystyrene petri dishes; requirements for all other materials, such as sterile pipettes and capped bottles of diluents and agar, are eliminated. Images PMID:4560475

FRONT VIEW OF POURING FROM #61 HOLDING FURNACE AT #02 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FRONT VIEW OF POURING FROM #61 HOLDING FURNACE AT #02 STATION INTO THREE VERTICAL MOLDS SUBMERGED IN A WATER-FILLED TANK BELOW THE CASTING FLOOR. THE CASTING CREW'S JOBS DURING THIS PHASE OF THE OPERATION INCLUDE REGULATING THE POURING RATE AND MONITORING THE VALVE RODS THAT CONTROL THE WATER SPRAYS ON THE MOLDS. DIFFERENT ALLOYS REQUIRE SPECIFIC POURING SPEEDS AND WATER PRESSURES. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY

Influence of volume ratio of liquid to solid and low pouring temperature on interface structure of cast Babbitt-steel bimetal composite

NASA Astrophysics Data System (ADS)

Fathy, Naglaa; Ramadan, Mohamed

2018-05-01

The influence of volume ratio of liquid to Solid and low pouring temperature on interface structure of cast Babbitt-steel bimetal composite was evaluated for static casting technique. At low pouring temperature of 380 °C, Babbitt microstructures are improved to be finer and more globular. On the other side pouring the Babbitt at low pouring temperature of 380 °C increases the chance of present higher unbonded area percent. Increasing the volume ratio of liquid to solid decreases the Sn-Pb interface thicknesses and increases the bonded interface area. In order to optimize the production of Babbitt-steel bimetal composite at low pouring temperature, the volume ratio of liquid Babbitt to solid steel shell should be higher value that could be more than 5 depending on the extrapolation of current data presented.

Effects of cold temperature and ethanol content on VOC ...

EPA Pesticide Factsheets

Emissions of speciated volatile organic compounds (VOCs), including mobile source air toxics (MSATs), were measured in vehicle exhaust from three light-duty spark ignition vehicles operating on summer and winter grade gasoline (E0) and ethanol blended (E10 and E85) fuels. Vehicle testing was conducted using a three-phase LA92 driving cycle in a temperature-controlled chassis dynamometer at two ambient temperatures (-7 °C and 24 °C). The cold start phase and cold ambient temperature increased VOC and MSAT emissions dramatically by up to several orders of magnitude compared to emissions during other phases and warm ambient temperature testing, respectively. As a result, calculated ozone formation potentials during the cold starts were significantly higher during cold temperature tests by 7 to 21 times the warm temperature values. The use of E85 fuel generally led to substantial reductions in hydrocarbons and increases in oxygenates such as ethanol and acetaldehyde compared to E0 and E10 fuels. However, the VOC emissions from E0 and E10 fuels were not significantly different. Cold temperature effects on cold start MSAT emissions varied by individual MSAT compound, but were consistent over a range of modern spark ignition vehicles. This manuscript communicates APPCD research activities on air toxics VOC emissions from mobile sources from the EPAct dynamometer study. Speciated VOC emissions from light-duty vehicles running on gasoline and ethanol blends at cold tem

The effect of a simple annealing heat treatment on the mechanical properties of cold-sprayed aluminum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, Aaron Christopher; Roemer, Timothy John; Hirschfeld, Deidre A.

2004-11-01

Cold spray, a new member of the thermal spray process family, can be used to prepare dense, thick metal coatings. It has tremendous potential as a spray-forming process. However, it is well known that significant cold work occurs during the cold spray deposition process. This cold work results in hard coatings but relatively brittle bulk deposits. This work investigates the mechanical properties of cold-sprayed aluminum and the effect of annealing on those properties. Cold spray coatings approximately 1 cm thick were prepared using three different feedstock powders: Valimet H-10; Valimet H-20; and Brodmann Flomaster. ASTM E8 tensile specimens were machinedmore » from these coatings and tested using standard tensile testing procedures. Each material was tested in two conditions: as-sprayed; and after a 300 C, 22 h air anneal. The as-sprayed material showed high ultimate strength and low ductility, with <1% elongation. The annealed samples showed a reduction in ultimate strength but a dramatic increase in ductility, with up to 10% elongation. The annealed samples exhibited mechanical properties that were similar to those of wrought 1100 H14 aluminum. Microstructural examination and fractography clearly showed a change in fracture mechanism between the as-sprayed and annealed materials. These results indicate good potential for cold spray as a bulk-forming process.« less

The effect of a simple annealing heat treatement on the mechanical properties of cold-sprayed aluminium.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, Aaron Christopher; Roemer, Timothy John; Hirschfeld, Deidre A.

2005-08-01

Cold spray, a new member of the thermal spray process family, can be used to prepare dense, thick metal coatings. It has tremendous potential as a spray-forming process. However, it is well known that significant cold work occurs during the cold spray deposition process. This cold work results in hard coatings but relatively brittle bulk deposits. This work investigates the mechanical properties of cold-sprayed aluminum and the effect of annealing on those properties. Cold spray coatings approximately 1 cm thick were prepared using three different feedstock powders: Valimet H-10: Valimet H-20: and Brodmann Flomaster. ASTM E8 tensile specimens were machinedmore » from these coatings and tested using standard tensile testing procedures. Each material was tested in two conditions: as-sprayed; and after a 300 C, 22h air anneal. The as-sprayed material showed high ultimate strength and low ductility, with <1% elongation. The annealed samples showed a reduction in ultimate strength but a dramatic increase in ductility, with up to 10% elongation. The annealed samples exhibited mechanical properties that were similar to those of wrought 1100 H14 aluminum. Microstructural examination and fractography clearly showed a change in fracture mechanism between the as-sprayed and annealed materials. These results indicate good potential for cold spray as a bulkforming process.« less

Operational experience with the supercritical helium during the TF coils tests campaign of SST-1

NASA Astrophysics Data System (ADS)

Panchal, Rohitkumar Natvarlal; Patel, Rakesh; Tank, Jignesh; Mahesuria, Gaurang; Sonara, Dashrath; Tanna, Vipul; Patel, Jayant; Srikanth, G. L. N.; Singh, Manoj; Patel, Ketan; Christian, Dikens; Garg, Atul; Bairagi, Nitn; Gupta, Manoj Kumar; Nimavat, Hiren; Shah, Pankil; Sharma, Rajiv; Pradhan, Subrata

2012-06-01

Under the 'SST-1 mission mandate' recently, all the sixteen Steady State Superconducting Tokamak (SST-1) Toroidal Field (TF) magnets have been successfully tested at their nominal currents of 10000 A in cold under supercritical helium (SHe) flow conditions. The TF magnets test campaign have begun in an experimental cryostat since June 2010 with the SST-1 Helium cryogenics facility, which is a 1.3 kW at 4.5 K helium refrigerator-cum-liquefier (HRL) system. The HRL provides ~300 g-s-1supercritical helium (SHe) with cold circulator (CC) as well as ~ 60 g-s-1 without cold circulator to fulfill the forced flow cooling requirements of SST- 1 magnets. In case of single TF coil tests, we can adjust HRL process parameters such that an adequate amount of required supercritical helium is available without the cold circulator. In this paper, the complete process is describing the Process Flow Diagram (PFD) of 1.3 kW at 4.5 K HRL, techniques to generate supercritical helium without using the cold-circulator and the results of the cooldown, steady state characteristics and experience of supercritical helium operations during the TF coils test campaign have been discussed.

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE KSC-375C-10036.31 108-KSC-375C-10036.31, P-21426, ARCHIVE-04502 Aerial oblique of Shuttle runway facilities. Pouring concrete on runway. Direction north - altitude 100'.

2014 Radiological Monitoring Results Associated with the Advanced Test Reactor Complex Cold Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, Mike

2015-02-01

This report summarizes radiological monitoring performed of the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste wastewater prior to discharge into the Cold Waste Pond and of specific groundwater monitoring wells associated with the Industrial Wastewater Reuse Permit (#LA-000161-01, Modification B). All radiological monitoring is performed to fulfill Department of Energy requirements under the Atomic Energy Act.

21-cm lensing and the cold spot in the cosmic microwave background.

PubMed

Kovetz, Ely D; Kamionkowski, Marc

2013-04-26

An extremely large void and a cosmic texture are two possible explanations for the cold spot seen in the cosmic microwave background. We investigate how well these two hypotheses can be tested with weak lensing of 21-cm fluctuations from the epoch of reionization measured with the Square Kilometer Array. While the void explanation for the cold spot can be tested with Square Kilometer Array, given enough observation time, the texture scenario requires significantly prolonged observations, at the highest frequencies that correspond to the epoch of reionization, over the field of view containing the cold spot.

Study of plate-fin heat exchanger and cold plate for the active thermal control system of Space Station

NASA Technical Reports Server (NTRS)

Chyu, MING-C.

1992-01-01

Plate-fin heat exchangers will be employed in the Active Thermal Control System of Space Station Freedom. During ground testing of prototypic heat exchangers, certain anomalous behaviors have been observed. Diagnosis has been conducted to determine the cause of the observed behaviors, including a scrutiny of temperature, pressure, and flow rate test data, and verification calculations based on such data and more data collected during the ambient and thermal/vacuum tests participated by the author. The test data of a plate-fin cold plate have been also analyzed. Recommendation was made with regard to further tests providing more useful information of the cold plate performance.

Advanced Vehicle Testing Activity Cold Weather On-road Testing of the Chevrolet Volt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smart, John

This report details cold weather on-road testing of a Chevrolet Volt. It quantifies changes in efficiency and electric range as ambient temperature changes. It will be published to INL's AVTA website as an INL technical report and will be accessible to the general public.

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY KSC-375C-10036.32 108-KSC-375C-10036.32, P-21425, ARCHIVE-04501 Aerial oblique of Shuttle Landing Facility. Pouring concrete on runway. Direction North - Altitude 100'.

Cold Shock as a Screen for Genes Involved in Cold Acclimatization in Neurospora crassa

PubMed Central

Watters, Michael K.; Manzanilla, Victor; Howell, Holly; Mehreteab, Alexander; Rose, Erik; Walters, Nicole; Seitz, Nicholas; Nava, Jacob; Kekelik, Sienna; Knuth, Laura; Scivinsky, Brianna

2018-01-01

When subjected to rapid drops of temperature (cold shock), Neurospora responds with a temporary shift in its morphology. This report is the first to examine this response genetically. We report here the results of a screen of selected mutants from the Neurospora knockout library for alterations in their morphological response to cold shock. Three groups of knockouts were selected to be subject to this screen: genes previously suspected to be involved in hyphal development as well as knockouts resulting in morphological changes; transcription factors; and genes homologous to E. coli genes known to alter their expression in response to cold shock. A total of 344 knockout strains were subjected to cold shock. Of those, 118 strains were identified with altered responses. We report here the cold shock morphologies and GO categorizations of strains subjected to this screen. Of strains with knockouts in genes associated with hyphal growth or morphology, 33 of 131 tested (25%) showed an altered response to cold shock. Of strains with knockouts in transcription factor genes, 30 of 145 (20%) showed an altered response to cold shock. Of strains with knockouts in genes homologous to E. coli genes which display altered levels of transcription in response to cold shock, a total of 55 of 68 tested (81%) showed an altered cold shock response. This suggests that the response to cold shock in these two organisms is largely shared in common. PMID:29563189

Mixing times in a stirred vessel with a modified turbine.

PubMed

Bombač, Andrej; Beader, Dečan; Zun, Iztok

2012-12-01

We present a mixing-time analysis for a double-disk turbine (DDT, SI Pat.No. 22243) and the well-known Rushton turbine (RuT) based on liquid stirring in a baffled vessel. The mixing time was measured locally based on the pulse/response technique. A small quantity of hot water, poured into the liquid bulk, just above the measurement location, was used as the pulse, while the change in the liquid temperature represented the system response. The results were obtained in two ways: (i) from measurements on the set-up and (ii) based on a CFD analysis. The pouring of the hot water was numerically simulated through the initialization of the scalar field. The duration of the temperature-pulse initialization around the measuring location corresponded to the pouring time in the experiment. All the energy introduced was freely swept away by the flow. The CFD-analyzed mixing times were consistently higher than the measured ones across the whole testing range, from 150 to 460 min-1. When comparing our mixing-time results with those from the literature based on a dimensionless mixing time we found them to be in good agreement.

Test of cold asphalt storability based on alternative approaches

NASA Astrophysics Data System (ADS)

Abaffyová, Zora; Komačka, Jozef

2017-09-01

Cold asphalt products for potholes repairs should be workable (soft enough) for long time to ensure their applicability. Storability is assessed indirectly using various tests of workability. Therefore, simple test methods (self-compaction and disintegration test) was developed and verified to investigate changes of storability of this group of cold asphalts. Selfcompaction of the tested mixture in the upturned Abram’s cone for the cement concrete slump test and in the mould for the California Bearing Ratio test was assessed in first stage. After that the video record of disintegration test was taken. During this test, the mould was lifted up and the mixture fell off the mould (Abram’s cone) or disintegrate (CBR mould). The drop of surface after 10 min self-compaction and netto time related to falling out or disintegration of the mixture were used to evaluate the mixture from storability point of view. It was found out the self-compaction test has not a potential to reveal and prove changes of mixture properties. Based on the disintegration test results it can be stated this test at 5 °C using the upturned Abram’s cone could be a suitable approach to determine qualitative changes of a cold mixture from storability point of view.

AGARD Flight Test Instrumentation Series. Volume 19. Digital Signal Conditioning for Flight Test. (Le Traitement du Signal Numerique pour les Essais n Vol)

DTIC Science & Technology

1991-06-01

intensive systems, including the use of onboard digital computers. Topics include: measurements that are digital in origin, sampling, encoding, transmitting...Individuals charged with designing aircraft measuring systems to become better acquainted with new solutions to their requirements. This volume Is...concerned with aircraft measuring systems as related to flight test and flight research. Measure - ments that are digital in origin or that must be

Another First at NSLS-II Construction Site

ScienceCinema

None

2017-12-09

Workers at the NSLS-II ring building construction site recently completed the first complicated concrete pour for the approximately 19-ft.-tall walls of the Utility Tunnel. The continuous pour was the first of its kind, as previous pours have been for foo

Comparison of denture base adaptation between CAD-CAM and conventional fabrication techniques.

PubMed

Goodacre, Brian J; Goodacre, Charles J; Baba, Nadim Z; Kattadiyil, Mathew T

2016-08-01

Currently no data comparing the denture base adaptation of CAD-CAM and conventional denture processing techniques have been reported. The purpose of this in vitro study was to compare the denture base adaptation of pack and press, pour, injection, and CAD-CAM techniques for fabricating dentures to determine which process produces the most accurate and reproducible adaptation. A definitive cast was duplicated to create 40 gypsum casts that were laser scanned before any fabrication procedures were initiated. A master denture was made using the CAD-CAM process and was then used to create a putty mold for the fabrication of 30 standardized wax festooned dentures, 10 for each of the conventional processing techniques (pack and press, pour, injection). Scan files from 10 casts were sent to Global Dental Science, LLC for fabrication of the CAD-CAM test specimens. After specimens for each of the 4 techniques had been fabricated, they were hydrated for 24 hours and the intaglio surface laser scanned. The scan file of each denture was superimposed on the scan file of the corresponding preprocessing cast using surface matching software. Measurements were made at 60 locations, providing evaluation of fit discrepancies at the following areas: apex of the denture border, 6 mm from the denture border, crest of the ridge, palate, and posterior palatal seal. The use of median and interquartile range was used to assess accuracy and reproducibility. The Levine and Kruskal-Wallis analysis of variance was used to evaluate differences between processing techniques at the 5 specified locations (α=.05). The ranking of results based on median and interquartile range determined that the accuracy and reproducibility of the CAD-CAM technique was more consistently localized around zero at 3 of the 5 locations. Therefore, the CAD-CAM technique showed the best combination of accuracy and reproducibility among the tested fabrication techniques. The pack and press technique was more accurate at 2 of the 5 locations; however, its interquartile range (reproducibility) was the greatest of the 4 tested processing techniques. The pour technique was the most reproducible at 2 of the 5 locations; however, its accuracy was the lowest of the tested techniques. The CAD-CAM fabrication process was the most accurate and reproducible denture fabrication technique when compared with pack and press, pour, and injection denture base processing techniques. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Cold Weather Admixture Systems Demonstration at Fort Wainwright, Alaska

DTIC Science & Technology

2010-08-01

3, and 5, the remaining two test sec- tions (Test Sections 2 and 4) were readied for concrete . The interior formwork was removed, and the rebar was...Washington, DC 20314-1000 ERDC/CRREL TR-10-6 ii Abstract: Cold Weather Admixture Systems (CWAS) is a new approach to cold weather concreting that...incorporates suites of commercially avail- able chemical admixtures in concrete mixes. When used in combination, these admixtures depress the freezing

Contribution des avortements et des grossesses extra-utérines dans la mortalité maternelle dans trois hôpitaux universitaires de Yaoundé

PubMed Central

Kamga, Danielle Victoire Tiako; Nana, Philip Njotang; Fouelifack, Florent Ymele; Fouedjio, Jeanne Hortence

2017-01-01

Introduction L'organisation mondiale de santé (OMS) estime que chaque année dans le monde 585 000 femmes meurent de complications liés à la grossesse, à l'accouchement, aux suites de couche et à l'avortement (ce dernier contribuant pour 13% des décès maternels). La GEU est responsable de 10% de mortalité maternelle au premier trimestre de la grossesse. Le taux de mortalité maternelle reste élevé au Cameroun, estimé à 782 pour 100 000 naissances vivantes selon EDS-MICS 2011. La contribution de ces deux entités dans la mortalité maternelle étant peu documentée dans notre pays, nous avons entrepris de réaliser cette étude avec pour objectif d'évaluer la contribution des avortements et des GEU dans la mortalité maternelle au Cameroun. Méthodes il s'agissait d'une étude rétrospective et analytique. Nous avons colligé tous les dossiers des patientes enceintes et décédées avant la 28ème semaine de grossesse, dans trois hôpitaux universitaires: Hôpital Central de Yaoundé (HCY), Hôpital Gynéco-Obstétrique et Pédiatrique de Yaoundé (HGOPY), Centre Hospitalier et Universitaire (CHU), sur la période allant du 1er juin 2011 au 31 mai 2016, soit sur cinq ans. Les données étaient compilées sur une fiche technique préétablie et testée, saisies en utilisant le logiciel CS pro 6.2 et analysées par le logiciel SPSS 20. Les tests statistiques de comparaison utilisés étaient le Khi 2 et le test de Fischer en fonction des effectifs. Le seuil de significativité était retenu pour P < 005. Résultats Tous avons enregistré 524 décès maternels pour 31116 naissances vivantes, soit un taux de mortalité maternelle (TMM) de 1538.9/100 000 naissances vivantes. Sur les 524 décès maternels, 414 dossiers étaient exploitables, parmi lesquels, 100 (soit 24.2%) concernaient les avortements et 24 (soit 5.8%) concernaient les grossesses extra-utérines, ces 2 entités contribuaient ainsi pour 30% de décès maternels (124 dossiers sur 414). L'analyse des 124 dossiers montre que l'âge moyen était de 27.58 +/-6 ans avec des extrêmes de 18 et 48. La tranche d'âge de 20 à 24 ans était la plus représentée (33.1%), suivie de celle de 25 à 29 ans (24.19%). Les célibataires constituaient 75%, les ménagères 36.7 %, de niveau d'instruction secondaire dans 62.5% et multigestes constituaient 36.1% de notre échantillon. Aucune consultation prénatale n'avait été initiée dans 73.4% et seulement 2.4% en avaient fait au moins 4. Les complications ayant conduit au décès étaient dominées par les hémorragies et les infections. Conclusion Les avortements et grossesse extra-utérines restent des causes majeures de la mortalité maternelle dans notre pays. Nous recommandons un renforcement de la planification familiale pour limiter les grossesses non désirées et une prise en charge par assistance socio-économique des patientes à risques. PMID:28979649

Caracterisation des revetements par projection thermique a haute vitesse obtenus a partir de differentes poudres de wc-10co-4cr pour des applications en aeronautique =

NASA Astrophysics Data System (ADS)

Quintero Malpica, Alfonso

Les revetements par projection thermique HVOF (High Velocity Oxy-Fuel) sont communement utilises dans l'industrie aeronautique, notamment au sein du partenaire industriel du projet (Tecnickrome Aeronautique Inc), comme des remplacants pour les revetements produits par l'electrodeposition du chrome dur due aux problemes environnementaux. Ce projet avait pour but de trouver une poudre alternative a celle qui est actuellement utilisee pour la production des revetements de type WC-10Co-4Cr obtenus avec la technologie de projection thermique a haute vitesse HVOF et en utilisant le systeme de projection HVOF-JET KOTERTM III. Dans un premier temps, cinq poudres incluant celle de reference, ayant des distributions granulometriques differentes, ont ete projetees dans le but d'identifier quelles poudres pouvaient etre utilisees avec le systeme de projection HVOF-JET KOTERTM III en gardant des parametres similaires (debit d'hydrogene, debit d'oxygene, debit de poudre et distance de projection) que pour la poudre de reference. Les revetements obtenus a partir des poudres etudiees ont ete evalues selon les criteres d'acceptation des revetements sollicites par les principaux manufacturiers des trains d'atterrissage. Les tests ont porte sur l'epaisseur, l'adhesion, la microstructure, la microdurete, les contraintes residuelles et la rugosite. A partir des resultats obtenus, seulement deux poudres ont rencontre toutes les proprietes demandees par les specifications aeronautiques. L'influence de la variation de la distance de projection sur la qualite des revetements a ete etudiee. Cinq distances (100, 125, 150, 175 et 200 mm) ont ete choisies pour faire la projection des deux poudres selectionnees. Les revetements obtenus ont montre de proprietes des revetements similaires (epaisseur, adhesion, microstructure, microdurete, contraintes residuelles et rugosite). Il a ete trouve que la distance de projection est un parametre indirect du systeme de projection HVOF-JET KOTERTM III et qu'autant la vitesse que la temperature des particules semblent mieux determiner les proprietes du revetement, en particulier, les niveaux de contraintes residuelles finales dans les revetements. Lorsque les revetements sont produits a de courtes distances de projection, les particules arrivent avec plus grande vitesse et temperature ce qui resulte dans de plus grandes temperatures du substrat et plus grande energie d'impact, resultant dans de plus grandes contraintes residuelles de compression dans les revetements.

Cold-End Subsystem Testing for the Fission Power System Technology Demonstration Unit

NASA Technical Reports Server (NTRS)

Briggs, Mazwell; Gibson, Marc; Ellis, David; Sanzi, James

2013-01-01

The Fission Power System (FPS) Technology Demonstration Unit (TDU) consists of a pumped sodiumpotassium (NaK) loop that provides heat to a Stirling Power Conversion Unit (PCU), which converts some of that heat into electricity and rejects the waste heat to a pumped water loop. Each of the TDU subsystems is being tested independently prior to full system testing at the NASA Glenn Research Center. The pumped NaK loop is being tested at NASA Marshall Space Flight Center; the Stirling PCU and electrical controller are being tested by Sunpower Inc.; and the pumped water loop is being tested at Glenn. This paper describes cold-end subsystem setup and testing at Glenn. The TDU cold end has been assembled in Vacuum Facility 6 (VF 6) at Glenn, the same chamber that will be used for TDU testing. Cold-end testing in VF 6 will demonstrate functionality; validated coldend fill, drain, and emergency backup systems; and generated pump performance and system pressure drop data used to validate models. In addition, a low-cost proof-of concept radiator has been built and tested at Glenn, validating the design and demonstrating the feasibility of using low-cost metal radiators as an alternative to highcost composite radiators in an end-to-end TDU test.

Métamatériaux pour la protection sismique

NASA Astrophysics Data System (ADS)

Guenneau, Sébastien; Enoch, Stefan; Colombi, Andrea; Roux, Philippe; Brule, Stéphane

2018-02-01

Les physiciens des ondes élaborent des modèles théoriques et numériques pour un contrôle accru de la lumière dans des matériaux structurés à l'échelle nanométrique et s'en inspirent pour contrôler les ondes mécaniques de Rayleigh dans des sols structurés à l'échelle métrique, avec des trous dans un sol ou des arbres en surface savamment agencés. Un transfert de paradigme s'opère entre les métamatériaux électromagnétiques pour la photonique et les métamatériaux sismiques pour le génie civil.

Acceptabilité du test VIH proposé aux nourrissons dans les services pédiatriques, en Côte d'Ivoire, Significations pour la couverture du diagnostic pédiatrique

PubMed Central

Oga, Maxime; Brou, Hermann; Dago-Akribi, Hortense; Coffie, Patrick; Amani-Bossé, Clarisse; Ékouévi, Didier; Yapo, Vincent; Menan, Hervé; Ndondoki, Camille; Timité-Konan, M.; Leroy, Valériane

2014-01-01

Résumé Problème: Le dépistage VIH chez les enfants a rarement été au centre des préoccupations des chercheurs. Quand le dépistage pédiatrique a retenu l'attention, cela a été pour éclairer seulement sur les performances diagnostiques en ignorant même que le test pédiatrique comme bien d'autres peut s'accepter ou se refuser. Cet article met au cœur de son analyse les raisons qui peuvent expliquer qu'on accepte ou qu'on refuse de faire dépister son enfant. Objectif: Etudier chez les parents, les mères, les facteurs explicatifs de l'acceptabilité du test VIH des nourrissons de moins de six mois. Méthodes: Entretien semi-directif à passages répétés avec les parents de nourrissons de moins de six mois dans les formations sanitaires pour la pesée/vaccination et les consultations pédiatriques avec proposition systématique d'un test VIH pour leur nourrisson. Résultats: Nous retenons que la réalisation effective du test pédiatrique du VIH chez le nourrisson repose sur trois éléments. Primo, le personnel de santé par son discours (qui dénote de ses connaissances et perceptions même sur l'infection) orienté vers les mères influence leur acceptation ou non du test. Secundo, la mère qui par ses connaissances et perceptions même sur le VIH, dont le statut particulier, l'impression de bien-être chez elle et son enfant influence toute réalisation du test pédiatrique VIH. Tertio, l'environnement conjugal de la mère, particulièrement caractérisé par les rapports au sein du couple, sur la facilité de parler du test VIH et sa réalisation chez les deux parents ou chez la mère seulement sont autant de facteurs qui influencent la réalisation effective du dépistage du VIH chez l'enfant. Le principe préventif du VIH, et le désir de faire tester l'enfant ne suffisent pas à eux seuls pour aboutir à sa réalisation effective, selon certaines mères confrontées au refus du conjoint. A l'opposé, les autres mères refusant la réalisation du test pédiatrique disent s'y opposer ; bien entendu, même dans le cas où le conjoint l'accepterait. Discussion: Les mères sont les principales mises en cause et craignent les réprimandes et la stigmatisation. Le père, le conjoint peut être un obstacle, quand il s'oppose au test VIH du nourrisson, ou devenir le facilitateur de sa réalisation s'il est convaincu. Le positionnement du père demeure donc essentiel dans la question de l'acceptabilité du VIH pédiatrique. Les mères en ont conscience et présagent des difficultés à faire dépister ou non les enfants sans avis préalable du conjoint à la fois père, et chef de famille. Conclusion: La question du dépistage pédiatrique du VIH, au terme de notre analyse, met en face trois éléments qui exigent une gestion globale pour assurer une couverture effective. Ces trois éléments n'existeraient pas sans s'influencer, donc ils sont constamment en interaction et empêchent ou favorisent la réalisation ou non du test pédiatrique. Aussi, dans une intention d'aboutir à une couverture effective du dépistage VIH des nourrissons, faut-il tenir compte d'une gestion harmonieuse de ces trois éléments: La première, la mère seule (avec ses connaissances, ses perceptions), son environnement conjugal (de proposition du test intégrant 1- l’époux et / ou père de l'enfant avec ses perceptions et connaissances sur l'infection 2- la facilité de parler du test et sa réalisation chez les deux ou un des parents, la mère) et les connaissances, attitudes et pratiques du personnel de l’établissement sanitaire sur l'infection du VIH. Recommandations: Nos recommandations proposent une redéfinition de l'approche du VIH/sida vers des familles exposées au VIH et une intégration plus accentuée du père facilitant leur propre acceptation du test VIH et celle de leur enfant. PMID:25088574

Lessons from history: morbidity of cold injury in the Royal Marines during the Falklands Conflict of 1982

PubMed Central

2013-01-01

Background Environmental conditions in the Falklands Conflict of 1982 favoured the genesis of cold injuries. Immediately, post-war, cold injury morbidity and its contributory factors were assessed, in the personnel of UK 3 Commando Brigade (3 Cdo Bde). Methods A questionnaire survey of the 3,006 members of 3 Cdo Bde who landed on the islands was conducted within 6–10 weeks of the end of hostilities. Questions included those relating to features of cold injury, body morphology, age, symptoms experienced, past medical history and other possible contributory causes. Additionally, the unit medical team conducted a cursory examination. Data were sent to the Royal Navy Institute of Naval Medicine (INM), where the degree of likely cold injury was broadly classified (‘asymptomatic’ ‘mild’, ‘moderate’ or ‘severe’). A sample (total 109) was then selected at random from each category and subsequently examined and tested at the INM (nerve conduction, photoplethysmography and thermography testing). Forty-seven non-cold exposed sailors acted as a control group. These contemporaneous records have now been identified and interrogated. Results Some 2,354 (78%) completed questionnaires were returned, revealing that 1,505 (64%) had experienced symptoms of non-freezing cold injury. The morbidity in the infantry units was significantly greater than that in the support troops (1,051 (76%) vs 454 (46%), p < 0.05). No evidence was found to support an influence of a number of factors, commonly believed to have an aetiological role in the production of cold injury. Whilst there was no significant relationship between past history and cold injury morbidity in the brigade as a whole, or within the infantry units alone, an association was identified in the collective infantry units (73%) and the support/headquarter units (59%) (p < 0.05). In comparison with uninjured sailors who acted as controls (n = 47), nerve conduction was impaired in 35% of those screened some months after returning to the UK, while the photoplethysmography and thermographic responses to a cold sensitivity test showed that most (including those classed by questionnaire as asymptomatic) had residual ‘cold sensitivity’. Conclusions Although the passage of time has made retrospective interrogation of historical documents hard, the available data do appear to offer valuable historical and clinical insights. Cold injury affected the majority of those fighting in the cold temperate climate of the Falklands. The overwhelming environmental conditions meant that, for most, a past history of cold injury did not appear to represent a risk factor for subsequent injury, as is the case for less severe conditions. Importantly, even asymptomatic individuals when tested often showed physiological evidence of cold injury—perhaps predisposing them to subsequent elevation in risk. PMID:24070118

Three-Dimensional Simulation of Traveling-Wave Tube Cold-Test Characteristics Using CST MICROWAVE STUDIO

NASA Technical Reports Server (NTRS)

Chevalier, Christine T.; Herrmann, Kimberly A.; Kory, Carol L.; Wilson, Jeffrey D.; Cross, Andrew W.; Santana , Samuel

2003-01-01

The electromagnetic field simulation software package CST MICROWAVE STUDIO (MWS) was used to compute the cold-test parameters - frequency-phase dispersion, on-axis impedance, and attenuation - for a traveling-wave tube (TWT) slow-wave circuit. The results were compared to experimental data, as well as to results from MAFIA, another three-dimensional simulation code from CST currently used at the NASA Glenn Research Center (GRC). The strong agreement between cold-test parameters simulated with MWS and those measured experimentally demonstrates the potential of this code to reduce the time and cost of TWT development.

40 CFR 1060.102 - What permeation emission control requirements apply for fuel lines?

Code of Federal Regulations, 2014 CFR

2014-07-01

... handheld Small SI engines installed in cold-weather equipment must meet the standards for EPA Cold-Weather... when measured according to the test procedure described in § 1060.515. (3) EPA Cold-Weather Fuel Lines... described in § 1060.515: Table 1 to § 1060.102—Permeation Standards for EPA Cold-Weather Fuel Lines Model...

Le pôle de métrologie de SOLEIL

NASA Astrophysics Data System (ADS)

Idir, M.; Brochet, S.; Delmotte, A.; Lagarde, B.; Mercere, P.; Moreno, T.; Polack, F.; Thomasset, M.

2006-12-01

Le Pôle de METROLOGIE de SOLEIL a pour objet de créer sur le synchrotron SOLEIL, une plateforme constituée : - une ligne de lumière utilisant le rayonnement synchrotron (métrologie dite à la longueur d'onde) - d'un laboratoire de métrologie associé (métrologie dite ll classique gg ) Ces deux types de Métrologie sont l'une et l'autre indispensables pour soutenir l'activité de recherche instrumentale en optique X et X-UV. Ce projet de pôle de METROLOGIE ne répondra pas seulement aux besoins des groupes chargés de l'équipement du synchrotron SOLEIL en optiques et détecteurs mais aussi pour préparer, tester et mettre au point les postes expérimentaux, ce qui concerne déjà une large communauté d'utilisateurs. Il sera aussi largement ouvert, dès sa mise en service, à l'ensemble de la communauté scientifique concernée par l'instrumentation X et XUV en Ile de France, en France, voire même en Europe si la demande continue de croître plus vite que l'offre dans ce domaine. Ligne de lumière Métrologie à la longueur d'onde La ligne de lumière sera équipée de plusieurs stations permettant de mesurer, dans la plus grande partie du spectre couvert par le synchrotron, les paramètres photométriques qui caractérisent les éléments optiques, tels que : la réflectivité de surfaces, l'efficacité de diffraction des réseaux, la diffusion des surfaces ou l'efficacité des détecteurs X et X-UV et la calibration absolue. Cette installation pourra servir également à développer des instruments et des diagnostics nécessaires à la caractérisation des faisceaux de rayons X (intensité, taille, degré de cohérence, polarisation etc.) Métrologie Classique La métrologie des surfaces optiques est devenue une nécessité critique pour les laboratoires et les industries qui utilisent les photons X et X-UV (synchrotrons, centres laser, etc. .). En effet, les progrès de calcul et de conception des systèmes optiques pour ces longueurs d'onde (optiques de microfocalisation, monochromateurs, diagnostics d'imagerie) font que les performances de ces instruments sont désormais limitées par les imperfections de fabrication des composants optiques. La métrologie des surfaces optiques est donc une nécessité impérieuse pour tous les acteurs du domaine, qui se doivent d'effectuer les contrôles appropriés. Cette pression s'exerce aussi sur les moyens utilisés pour effectuer ces mesures, car les incertitudes de mesure actuelles, notamment en ce qui concerne la régularité des surfaces, sont loin d'être négligeables vis à vis des tolérances demandées. Il est donc indispensable de faire évoluer les instruments de mesure et d'obtenir des gains significatifs de précision. Un travail particulier est en cours au laboratoire de Métrologie pour développer à côté des instruments commerciaux, des instruments prototypes sur des concepts originaux (mesures de profils de surface et mesures d'angle). Dans cet article, nous donnons des détails des choix techniques utilisés sur la ligne de METROLOGIE et TESTS et des performances attendues et nous décrirons le laboratoire de METROLOGIE en donnant des exemples d'optiques récemment testées.

High Noon for High Stakes: Alfie Kohn at Middlebury College.

ERIC Educational Resources Information Center

Barna, Ed

2002-01-01

The tougher standards movement has five fatal flaws. An emphasis on scores limits student willingness to experiment and be challenged. The "basic skills" approach to teaching--pouring knowledge down student throats--has never worked well. Standardized testing necessarily creates winners and losers. Accountability is coercive and…

Robust, Nontoxic, Antifouling Polymer.

DTIC Science & Technology

1996-02-23

easily removable slime of no more than 50 micron 9 thickness was observed on the test panel. Note that the slime was easily removed using 10 light...viscous syrup remains. Pour tbe 2 syrup into molds and heat under vacuum at 120 °C untfl a cured antifouling bulk material 3 is obtained. 4 Example

The effect of cold priming on the fitness of Arabidopsis thaliana accessions under natural and controlled conditions.

PubMed

Cvetkovic, Jelena; Müller, Klaus; Baier, Margarete

2017-03-09

Priming improves an organism's performance upon a future stress. To test whether cold priming supports protection in spring and how it is affected by cold acclimation, we compared seven Arabidopsis accessions with different cold acclimation potentials in the field and in the greenhouse for growth, photosynthetic performance and reproductive fitness in March and May after a 14 day long cold-pretreatment at 4 °C. In the plants transferred to the field in May, the effect of the cold pretreatment on the seed yield correlated with the cold acclimation potential of the accessions. In the March transferred plants, the reproductive fitness was most supported by the cold pretreatment in the accessions with the weakest cold acclimation potential. The fitness effect was linked to long-term effects of the cold pretreatment on photosystem II activity stabilization and leaf blade expansion. The study demonstrated that cold priming stronger impacts on plant fitness than cold acclimation in spring in accessions with intermediate and low cold acclimation potential.

Effets thermoelectrique et thermomagnetique du yttrium barium copper oxide monocristallin

NASA Astrophysics Data System (ADS)

Ghamlouche, Hassan

1998-09-01

Des la decouverte des supraconducteurs a haute temperature critique, les recherches se sont intensifiees afin de comprendre les mecanismes qui sont a l'origine des proprietes de ces materiaux L'etat mixte, tout comme l'etat supraconducteur pur et l'etat normal, a fait l'objet de nombreux travaux de recherche. En particulier, la structure des vortex a l'etat mixte, et leur mouvement sous l'effet d'une force quelconque, etaient et restent le centre de preoccupation. Les effets thermoelectrique (Seebeck) et thermomagnetique (Nernst) sont parmi les differentes mesures qui peuvent donner de l'information sur les etats des vortex a l'etat mixte. L'avantage essentiel de ces deux effets est l'absence d'un courant electrique applique. Ce dernier peut donner des perturbations indesirables durant les mesures. D'autre pari, nous avons utilise la methode CA (Courant Alternatif) pour effectuer nos mesures. Cette methode est caracterisee par une meilleure resolution par rapport a la methode CC (Courant Continu) conventionnelle. Nous avons etudie autant des echantillons macles que des echantillons sans macles. D'abord nous avons teste notre montage a champ magnetique nul. Nous avons alors montre que le pic rapporte par certains dans l'effet Seebeck a la transition supraconductrice ne correspond pas a une realite physique mais a un artefact experimental. On avait associe ce pic aux fluctuations. Par la suite, nous avons mis en evidence et etudie pour la premiere fois avec les effets Seebeck et Nernst le phenomene de la fusion du reseau de vortex grace a des mesures sur les echantillons sans macles. Cette etude s'est faite pour deux concentrations d'oxygene differentes et pour un gradient de temperature parallele, consecutivement, aux deux axes cristallographiques dans le plan ab. Finalement, nous avons etudie l'effet des plans de maclage sur le mouvement des vortex. Ceci a ete realise en appliquant le gradient de temperature selon trois directions differentes (0, 45 et 90°) avec les plans de maclage. Nous avons observe, pour le premier angle un mouvement libre du vortex, pour le second angle une contribution de l'effet Nernst a l'effet Seebeck et pour la troisieme direction un phenomene d'activation. Dans ce dernier cas, les plans de maclage font un obstacle qui s'oppose au mouvement des vortex. De ce qui precede, nous concluons qu'avec la bonne resolution de notre technique nous sommes capables d'observer des phenomenes que la technique CC ne met pas en relief. D'autre part, la variete d'echantillons que nous avons etudies et les phenomenes que nous avons observes valorisent la presente etude.

Optimisation des trajectoires verticales par la methode de la recherche de l'harmonie =

NASA Astrophysics Data System (ADS)

Ruby, Margaux

Face au rechauffement climatique, les besoins de trouver des solutions pour reduire les emissions de CO2 sont urgentes. L'optimisation des trajectoires est un des moyens pour reduire la consommation de carburant lors d'un vol. Afin de determiner la trajectoire optimale de l'avion, differents algorithmes ont ete developpes. Le but de ces algorithmes est de reduire au maximum le cout total d'un vol d'un avion qui est directement lie a la consommation de carburant et au temps de vol. Un autre parametre, nomme l'indice de cout est considere dans la definition du cout de vol. La consommation de carburant est fournie via des donnees de performances pour chaque phase de vol. Dans le cas de ce memoire, les phases d'un vol complet, soit, une phase de montee, une phase de croisiere et une phase de descente, sont etudies. Des " marches de montee " etaient definies comme des montees de 2 000ft lors de la phase de croisiere sont egalement etudiees. L'algorithme developpe lors de ce memoire est un metaheuristique, nomme la recherche de l'harmonie, qui, concilie deux types de recherches : la recherche locale et la recherche basee sur une population. Cet algorithme se base sur l'observation des musiciens lors d'un concert, ou plus exactement sur la capacite de la musique a trouver sa meilleure harmonie, soit, en termes d'optimisation, le plus bas cout. Differentes donnees d'entrees comme le poids de l'avion, la destination, la vitesse de l'avion initiale et le nombre d'iterations doivent etre, entre autre, fournies a l'algorithme pour qu'il soit capable de determiner la solution optimale qui est definie comme : [Vitesse de montee, Altitude, Vitesse de croisiere, Vitesse de descente]. L'algorithme a ete developpe a l'aide du logiciel MATLAB et teste pour plusieurs destinations et plusieurs poids pour un seul type d'avion. Pour la validation, les resultats obtenus par cet algorithme ont ete compares dans un premier temps aux resultats obtenus suite a une recherche exhaustive qui a utilisee toutes les combinaisons possibles. Cette recherche exhaustive nous a fourni l'optimal global; ainsi, la solution de notre algorithme doit se rapprocher le plus possible de la recherche exhaustive afin de prouver qu'il donne des resultats proche de l'optimal global. Une seconde comparaison a ete effectuee entre les resultats fournis par l'algorithme et ceux du Flight Management System (FMS) qui est un systeme d'avionique situe dans le cockpit de l'avion fournissant la route a suivre afin d'optimiser la trajectoire. Le but est de prouver que l'algorithme de la recherche de l'harmonie donne de meilleurs resultats que l'algorithme implemente dans le FMS.

Refractive Surgery: New Techniques and Usability for Military Personnel (La chirurgie refractive: Nouvelles techniques et leur application pour le personnel militaire)

DTIC Science & Technology

2012-11-01

de loin sans correction, la chirurgie réfractive permet aux jeunes recrues ou militaires du rang de satisfaire aux normes de vision sans...correction exigées pour le métier militaire de leur choix, d’où une augmentation du nombre de candidats et la possibilité pour les individus...réfractive risquent d’engendrer des handicaps visuels et d’écourter des carrières militaires. Pour cette raison, la qualité du service fourni

Que peut-on voir avec des neutrons? Une introduction pour des non spécialistes

NASA Astrophysics Data System (ADS)

Schweizer, J.

2005-11-01

Le neutron est une particule élémentaire qui a été découverte en 1932 par James Chadwick. Ses caractéristiques principales sont résumées dans le tableau I. Il a été utilisé pour la première fois par Clifford Shull en 1946 comme outil pour des expériences de diffusion. Cette technique s'est depuis constamment développée pour concerner tous les aspects de la matière condensée: physique, chimie, matériaux, biologie. Il s'agit d'un outil tout à fait exceptionnel car le neutron possède des propriétés uniques et particulièrement adaptées pour ces études.

40 CFR 600.113-08 - Fuel economy calculations for FTP, HFET, US06, SC03 and cold temperature FTP tests.

Code of Federal Regulations, 2013 CFR

2013-07-01

... EMISSIONS OF MOTOR VEHICLES Fuel Economy and Carbon-Related Exhaust Emission Test Procedures § 600.113-08 Fuel economy calculations for FTP, HFET, US06, SC03 and cold temperature FTP tests. The Administrator... specific gravity, carbon weight fraction and net heating value of the test fuel must be determined. The FTP...

40 CFR 86.1336-84 - Engine starting, restarting, and shutdown.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (4) If a failure to start occurs during the hot start portion of the test and is caused by engine... stalling. (1) If the engine stalls during the initial idle period of either the cold or hot start test, the engine shall be restarted immediately using the appropriate cold or hot starting procedure and the test...

40 CFR 86.1336-84 - Engine starting, restarting, and shutdown.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (4) If a failure to start occurs during the hot start portion of the test and is caused by engine... stalling. (1) If the engine stalls during the initial idle period of either the cold or hot start test, the engine shall be restarted immediately using the appropriate cold or hot starting procedure and the test...

40 CFR 86.1336-84 - Engine starting, restarting, and shutdown.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (4) If a failure to start occurs during the hot start portion of the test and is caused by engine... stalling. (1) If the engine stalls during the initial idle period of either the cold or hot start test, the engine shall be restarted immediately using the appropriate cold or hot starting procedure and the test...

Influence of coating defects on the corrosion behavior of cold sprayed refractory metals

NASA Astrophysics Data System (ADS)

Kumar, S.; Rao, A. Arjuna

2017-02-01

The defects in the cold sprayed coatings are critical in the case of corrosion performances of the coatings in aggressive conditions. To understand the influence of coating defects on corrosion, immersion tests have been carried out in HF solution for the cold sprayed and heat treated Titanium, Tantalum and Niobium coatings. Long duration immersion tests reveal inhomogeneous weight losses of the samples prepared at different heat treatment conditions. The weight loss for different coatings has been well corroborated with the coating defects and microstructures. Chemical and micro structural analysis elucidates the reason behind the inhomogeneous performance of different type of cold sprayed coatings in corrosion medium. In the case of cold sprayed titanium, formation of stable oxide along the inter-splat boundary hinders the aggressive attack of the corrosion medium which is not so in other cases.

Profil épidémiologique des pathologies respiratoires chez l’enfant à l’Hôpital d’Enfants de Rabat, Maroc

PubMed Central

Benchekroun, Ilham; Boubkraoui, Mohamed El Mahdi; Mekaoui, Nour; Karboubi, Lamia; Mahraoui, Chafiq; Dakhama, Badr Sououd Benjelloun

2017-01-01

Introduction Les pathologies respiratoires représentent un motif fréquent d'hospitalisation en pédiatrie. L'objectif de cette étude était d'évaluer le profil épidémiologique des pathologies respiratoires chez l'enfant à l'hôpital d'enfants de Rabat, Maroc. Méthodes Il s'agit d'une étude observationnelle transversale qui a concerné tous les cas d'enfants âgés de 3 mois à 15 ans hospitalisés pour une pathologie respiratoire au service de pneumoallergologie et infectiologie pédiatriques de l'hôpital d'enfants de Rabat sur une période d'une année, du 1 janvier 2014 au 31 décembre 2014. Résultats Sur 3537 patients hospitalisés, 2493 (70,5%) l'ont été pour une pathologie respiratoire. Les hospitalisations pour exacerbation d'asthme (p < 0,001), bronchiolite aigüe (p < 0,001) et dyspnée laryngée (p = 0,004) étaient plus fréquentes chez le garçon alors que les hospitalisations pour pneumopathie aigüe (p = 0,005), pour inhalation de corps étranger (p = 0,007) et pour coqueluche (p = 0,020) étaient plus fréquentes chez la fille. Les hospitalisations pour pneumopathie aigüe (p < 0,001), exacerbation de séquelles graves de virose (p < 0,001) et pour coqueluche (p < 0,001) étaient plus fréquentes chez le nourrisson. Les hospitalisations pour pneumopathie aigüe (p < 0,001) et pour coqueluche (p = 0,015) étaient plus fréquentes en période automnohivernale. Conclusion Les motifs d'hospitalisation étaient dominés par les exacerbations d'asthme et la bronchiolite aigüe, lesquelles étaient plus fréquentes chez le garçon. Les infections respiratoires, représentées par les pneumopathies aigües et la coqueluche, étaient plus fréquentes en période automnohivernale et touchaient plus le nourrisson. PMID:29675122

Test Operations Procedure (TOP) 1-1-003 Cold Regions Personnel Effects

DTIC Science & Technology

2008-09-15

4 3.3 Freezing Injuries : Frostnip and Frostbite...4 3.4 Non-freezing injuries ........................................................................... 5 3.5 Snow...3. Information concerning the symptoms, methods of prevention, and treatment of various types of cold injuries is also provided. 2.2 Cold Weather

Knowledge, Attitude and Practice of Ear Care in Coastal Karnataka.

PubMed

Dosemane, Deviprasad; Ganapathi, Keerthan; Kanthila, Jayashree

2015-12-01

Ear as an organ is necessary for the perception of sound and body balance. Ear infection, diabetes mellitus, hypertension and excessive use of mobile phone for listening to music at high volume all can reduce hearing. No earlier study was available in the costal Karnataka population, regarding the practice of ear care. The study objective was to ascertain the level of knowledge of the community regarding ear care, to find out whether some of the common conditions affecting hearing are known and to find out the common practices involved in maintaining ear hygiene. This cross-sectional study was conducted on 500 subjects in two tertiary care hospitals by convenient sampling, using self-administered questionnaire. Knowledge, Attitude and Practice across the age groups, religion & education background were studied. Across different education groups, 66.7%-90% did not know that 'cold' can cause ear infection and 46.7%-75.0% did not know that diabetes and hypertension can reduce hearing. When there is ear pain or discharge, people put ear drops available at home in 48.3%-75.0% across 3 age groups; 58.5%-61.5% across 3 religions and 44.8%-67.9% across 5 education groups. No statistically significant difference was found in the practice of pouring oil into ears across religions. A total of 58.6%-100% daily clean inside the ear and 70-100% use cotton buds. General perception of the people is that ear is necessary only for hearing. Majority did not know that nasal infection can affect the ear and that DM and hypertension can cause hearing loss. When there is ear pain and discharge, most of the adults put drops that are available at home. Pouring oil into the ears and cleaning inside the ear canals is routinely practiced in costal Karnataka.

Les campagnes de dépistage du VIH, une stratégie efficace pour l’accès universel à la prévention et au traitement ? L’expérience du Burkina Faso

PubMed Central

Somé, J.F.; Desclaux, A.; Ky-Zerbo, O.; Lougué, M.; Kéré, S.; Obermeyer, C.; Simaga, F.

2014-01-01

Objectifs l’augmentation du taux de personnes qui connaissent leur statut VIH est un impératif, notamment en Afrique subsaharienne, ce qui impose d’évaluer les stratégies utilisées pour accroître la fréquentation des services de dépistage. Cet article vise à faire le bilan de la pertinence, de la faisabilité et de l’efficacité des campagnes nationales de dépistagemenées entre 2006 et 2010 au Burkina Faso. Méthodologie une analyse de toutes les données de fréquentation du conseil dépistage sur cette période a été faite, couplée à des entretiens avec les principaux acteurs intervenant dans le dépistage. Résultats les résultats montrent que les huit campagnes de dépistage organisées sur la période ont permis à 487 727 personnes de faire leur test VIH. Ce nombre représente 50 % du nombre total de personnes ayant fait leur test et contribue à hauteur de 24,6 % au dépistage des personnes séropositives identifiées au cours de cette période. Les campagnes ont touché des populations difficiles à atteindre (en particulier les jeunes), à un coût moindre. Conclusions cette stratégie est donc pertinente pour identifier les personnes VIH+. Son intérêt pour la prévention, important selon les soignants et au vu des populations jeunes qui y participent, devrait être mesuré par des études complémentaires. Les campagnes sont efficaces et coût-efficaces même dans un pays de niveau de prévalence faible. Ces résultats soulignent l’intérêt de la synergie entre les associations et les services de santé dans l’offre de services de conseil et dépistage. PMID:24681563

COLD TEMPERATURE MOTOR VEHICLE EMISSIONS TESTING IN ALASKA

EPA Science Inventory

A motor vehicle emissions testing study was conducted in Anchorage and Fairbanks during the winter of 1998-99 to collect actual measurements of initial idle emission rates. The study was performed for a sample of 111 automobiles and light-duty trucks under cold wintertime ambient...

40 CFR 63.7710 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... gases from mold vents in pouring areas and pouring stations that use a sand mold system. This operation... including quality assurance procedures. (iv) How the bag leak detection system will be maintained including...) Procedures for providing an ignition source to mold vents of sand mold systems in each pouring area and...

Performance evaluation approach for the supercritical helium cold circulators of ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaghela, H.; Sarkar, B.; Bhattacharya, R.

2014-01-29

The ITER project design foresees Supercritical Helium (SHe) forced flow cooling for the main cryogenic components, namely, the superconducting (SC) magnets and cryopumps (CP). Therefore, cold circulators have been selected to provide the required SHe mass flow rate to cope with specific operating conditions and technical requirements. Considering the availability impacts of such machines, it has been decided to perform evaluation tests of the cold circulators at operating conditions prior to the series production in order to minimize the project technical risks. A proposal has been conceptualized, evaluated and simulated to perform representative tests of the full scale SHe coldmore » circulators. The objectives of the performance tests include the validation of normal operating condition, transient and off-design operating modes as well as the efficiency measurement. A suitable process and instrumentation diagram of the test valve box (TVB) has been developed to implement the tests at the required thermodynamic conditions. The conceptual engineering design of the TVB has been developed along with the required thermal analysis for the normal operating conditions to support the performance evaluation of the SHe cold circulator.« less

Experimental Study of Axially Tension Cold Formed Steel Channel Members

NASA Astrophysics Data System (ADS)

Apriani, Widya; Lubis, Fadrizal; Angraini, Muthia

2017-12-01

Experimental testing is commonly used as one of the steps to determine the cause of the collapse of a building structure. The collapse of structures can be due to low quality materials. Although material samples have passed laboratory tests and the existing technical specifications have been met but there may be undetected defects and known material after failure. In this paper will be presented Experimental Testing of Axially Tension Cold Formed Steel Channel Members to determine the cause of the collapse of a building roof truss x in Pekanbaru. Test of tensile strength material cold formed channel sections was performed to obtain the main characteristics of Cold Formed steel material, namely ultimate tensile strength loads that can be held by members and the yield stress possessed by channel sections used in construction. Analysis of axially tension cold formed steel channel section presents in this paper was conducted through experimental study based on specificationsAnnualBook of ASTM Standards: Metal Test methods and Analitical Procedures, Section 3 (1991). The result of capacity loads experimental test was compared with design based on SNI 03-7971-2013standard of Indonesia for the design of cold formed steel structural members. The results of the yield stress of the material will be seen against the minimum allowable allowable stress range. After the test, the percentace of ultimate axial tension capacity theory has a result that is 16.46% larger than the ultimate axial tension capacity experimental. When compared with the load that must be borne 5.673 kN/m it can be concluded that 2 specimens do not meet. Yield stress of member has fulfilled requirement that wass bigger than 550 MPa. Based on the curve obtained ultimate axial tension capacity theory, results greater than experimental. The greatest voltage value (fu) is achieved under the same conditions as its yield stress. For this specimen with a melting voltage value fy = 571.5068 MPa has fulfilled the minimum melting point value of 550 MPa required for standard mild steel materials in accordance with the code SNI 03-7971-2013 about Cold formed steel.

Experimental Study of Axially Tension Cold Formed Steel Channel Members

NASA Astrophysics Data System (ADS)

Apriani, Widya; Lubis, Fadrizal; Angraini, Muthia

2017-12-01

Experimental testing is commonly used as one of the steps to determine the cause of the collapse of a building structure. The collapse of structures can be due to low quality materials. Although material samples have passed laboratory tests and the existing technical specifications have been met but there may be undetected defects and known material after failure. In this paper will be presented Experimental Testing of Axially Tension Cold Formed Steel Channel Members to determine the cause of the collapse of a building roof truss x in Pekanbaru. Test of tensile strength material cold formed channel sections was performed to obtain the main characteristics of Cold Formed steel material, namely ultimate tensile strength loads that can be held by members and the yield stress possessed by channel sections used in construction. Analysis of axially tension cold formed steel channel section presents in this paper was conducted through experimental study based on specificationsAnnualBook of ASTM Standards: Metal Test methods and Analitical Procedures, Section 3 (1991). The result of capacity loads experimental test was compared with design based on SNI 03-7971- 2013standard of Indonesia for the design of cold formed steel structural members. The results of the yield stress of the material will be seen against the minimum allowable allowable stress range. After the test, the percentace of ultimate axial tension capacity theory has a result that is 16.46% larger than the ultimate axial tension capacity experimental. When compared with the load that must be borne 5.673 kN/m it can be concluded that 2 specimens do not meet. Yield stress of member has fulfilled requirement that wass bigger than 550 MPa. Based on the curve obtained ultimate axial tension capacity theory, results greater than experimental. The greatest voltage value (fu) is achieved under the same conditions as its yield stress. For this specimen with a melting voltage value fy = 571.5068 MPa has fulfilled the minimum melting point value of 550 MPa required for standard mild steel materials in accordance with the code SNI 03- 7971-2013 about Cold formed steel.

Exposure to heat and freezing in the vaccine cold chain in Thailand.

PubMed

Techathawat, Sirirat; Varinsathien, Porpit; Rasdjarmrearnsook, Aimorn; Tharmaphornpilas, Piyanit

2007-01-26

This study investigated exposure to heat and freezing of vaccines used in Thailand's National Immunization Program. Cold chain temperatures on 48 randomly selected shipment routes nationwide were monitored. Measles and hepatitis B vaccines were despatched with recording devices and subsequently tested. The study found that extremes of cold appear to be the more significant problem. Heat exposure was relatively brief and not at very high temperatures, so vaccine deterioration was unlikely, as was confirmed by measles vaccine testing. Exposure to temperatures below -0.5 degrees C was widespread, which would be expected to damage hepatitis B vaccine, but shake tests did not detect damage.

Singaporean college students overpour drinks similar to Western populations: influence of peer presence in a simulated alcohol-pouring task.

PubMed

Zandy, Shannon L; Pang, Joyce S; Ho, Moon-Ho Ringo; Matthews, Douglas B

2013-11-01

College drinking is a global health concern. However, most studies originate from countries with high alcohol consumption. In the United States, college students overpour a standard alcoholic drink, yet it is unclear if this remains true in countries with low alcohol consumption. Additionally, in college, peer influence is the greatest predictor of drinking behavior, yet it is unknown if social norms affect how students pour drinks. This study examined how male college students, in a country with low alcohol consumption, define standard drinks, and if the presence of an unfamiliar peer affects how students pour during a simulated alcohol-pouring task. Male undergraduate students (n = 105) underwent baseline assessments of impulsivity, self-monitoring, religiosity, and drinking characteristics. Participants poured fluid into empty cups of different sizes to equal a standard serving of beer or shot of liquor. There were 2 groups based on gender of experimenter. Within each group, participants were randomly assigned to Alone or Dyad condition. In the Alone condition, students were instructed to pour only for themselves. In the Dyad condition, students were instructed to pour for themselves and the experimenter. The volumes poured by the students were compared with standards used in Singapore and the United States. Collapsed across container size, students overpoured shots by 50% and beer by 100% when compared to the standard drink definition in Singapore. When using a more liberal definition, students overpoured beer by 25%, but did not overpour shots. In the presence of an unfamiliar peer, overpouring decreased by 10% for beer. The current data show that college students, in a country with low alcohol consumption, overestimate standard alcoholic drinks similar to their Western counterparts and use social norms to determine how much to pour for a drink when confronted with an unfamiliar peer. Efforts toward creating internationally recognized standard drink definitions should be considered. Copyright © 2013 by the Research Society on Alcoholism.

Clinical Cold Welding of the Modular Total Hip Arthroplasty Prosthesis.

PubMed

Whittaker, Robert K; Zaghloul, Ahmed M; Hothi, Harry S; Siddiqui, Imran A; Blunn, Gordon W; Skinner, John A; Hart, Alister J

2017-02-01

A head that is "clinically cold welded" to a stem is one of the commonest reasons for unplanned removal of the stem. It is not clear which hip designs are at greatest risk of clinical cold welding. This was a case-control study of consecutively received hip implant retrievals; we chose the design of hip that had the greatest number of truly cold-welded heads (n = 11). For our controls, we chose retrieved hips of the same design but without cold welding of the head (n = 35). We compared the clinical variables between these 2 groups using nonparametric Mann-Whitney tests to investigate the significance of differences between the cold-welded and non-cold-welded groups. The design that most commonly caused cold welding was a combination of a Ti stem and Ti taper: 11 out of 48 (23%) were truly cold welded. Comparison of the clinical data showed that no individual factor could be used to predict this preoperatively with none of the 4 predictors tested showing any significance: (1) time to revision (P = .687), (2) head size (P = .067), (3) patient age at primary (P = .380), and (4) gender (P = .054). We have shown that clinical cold welding is most prevalent in Ti-Ti combinations of the stem and taper; approximately 25% of cases received at our center were cold welded. Analysis of clinical variables showed that it is not possible to predict which will be cold welded preoperatively. Surgeons should be aware of this potential complication when revising a Ti-Ti stem/head junction. Copyright © 2016 Elsevier Inc. All rights reserved.

ETR HEAT EXCHANGER BUILDING, TRA644. SOUTH SIDE. CAMERA FACING NORTH. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ETR HEAT EXCHANGER BUILDING, TRA-644. SOUTH SIDE. CAMERA FACING NORTH. NOTE POURED CONCRETE WALLS. ETR IS AT LEFT OF VIEW. NOTE DRIVEWAY INSET AT RIGHT FORMED BY DEMINERALIZER WING AT RIGHT. SOUTHEAST CORNER OF ETR, TRA-642, IN VIEW AT UPPER LEFT. INL NEGATIVE NO. HD46-36-1. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Reactor Simulator Testing

NASA Technical Reports Server (NTRS)

Schoenfeld, Michael P.; Webster, Kenny L.; Pearson, Boise J.

2013-01-01

As part of the Nuclear Systems Office Fission Surface Power Technology Demonstration Unit (TDU) project, a reactor simulator test loop (RxSim) was design & built to perform integrated testing of the TDU components. In particular, the objectives of RxSim testing was to verify the operation of the core simulator, the instrumentation and control system, and the ground support gas and vacuum test equipment. In addition, it was decided to include a thermal test of a cold trap purification design and a pump performance test at pump voltages up to 150 V since the targeted mass flow rate of 1.75 kg/s was not obtained in the RxSim at the originally constrained voltage of 120 V. This paper summarizes RxSim testing. The gas and vacuum ground support test equipment performed effectively in NaK fill, loop pressurization, and NaK drain operations. The instrumentation and control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings. The cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained which was lower than the predicted 750 K but 156 K higher than the cold temperature indicating the design provided some heat regeneration. The annular linear induction pump (ALIP) tested was able to produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz.

Reactor Simulator Integration and Testing

NASA Technical Reports Server (NTRS)

Schoenfield, M. P.; Webster, K. L.; Pearson, J. B.

2013-01-01

As part of the Nuclear Systems Office Fission Surface Power Technology Demonstration Unit (TDU) project, a reactor simulator (RxSim) test loop was designed and built to perform integrated testing of the TDU components. In particular, the objectives of RxSim testing were to verify the operation of the core simulator, the instrumentation and control system, and the ground support gas and vacuum test equipment. In addition, it was decided to include a thermal test of a cold trap purification design and a pump performance test at pump voltages up to 150 V because the targeted mass flow rate of 1.75 kg/s was not obtained in the RxSim at the originally constrained voltage of 120 V. This Technical Memorandum summarizes RxSim testing. The gas and vacuum ground support test equipment performed effectively in NaK fill, loop pressurization, and NaK drain operations. The instrumentation and control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings. The cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained, which was lower than the predicted 750 K but 156 K higher than the cold temperature, indicating the design provided some heat regeneration. The annular linear induction pump tested was able to produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz.

CRACK GROWTH RESPONSE OF ALLOY 690 IN SIMULATED PWR PRIMARY WATER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toloczko, Mychailo B.; Bruemmer, Stephen M.

2009-12-01

The stress corrosion crack growth response of three extruded alloy 690 CRDM tube heats was investigated in several thermomechanical conditions. Extremely low propagation rates (< 1 x 10{sup -9} mm/s) were observed under constant stress intensity factor (K) loading at 325-350 C in the as-received, thermally treated (TT) materials despite using a variety of transitioning techniques. Post-test observation of the crack-growth surfaces revealed only isolated intergranular (IG) cracking. One-dimensional cold rolling to 17% reduction and testing in the S-L orientation did not promote enhanced stress corrosion rates. However, somewhat higher propagation rates were observed in a 30% cold-rolled alloy 690TTmore » specimen tested in the T-L orientation. Cracking of the cold-rolled material was promoted on grain boundaries oriented parallel to the rolling plane with the % IG increasing with the amount of cold rolling.« less

The Effects of Cold Whirlpool on Power, Speed, Agility, and Range of Motion

PubMed Central

Patterson, Stephen M.; Udermann, Brian E.; Doberstein, Scott T.; Reineke, David M.

2008-01-01

The purpose was to determine if cold whirlpool treatment decreases functional performance equally regardless of gender. A secondary aim was to determine if there is a gradual increase in functional performance across time. Twenty-one college-aged subjects volunteered to participate in this study and were required to perform four measures of functional performance including: counter movement vertical jump, T-test, 36.58-meter dash (40-yard), and active range of motion of the ankle. Participants were treated with a 20 minute, 10 degree Celsius cold whirlpool following the pre-test of a given functional performance measure. Participants demonstrated significant decreases in counter movement vertical jump, T-test, and 40-yard dash performance immediately following treatment. Vertical jump performance remained impaired for at least 32 minutes. While both the T-test and 40-yard dash were affected for 7 and 22 minutes post- treatment, respectively. Participants also demonstrated significant decreases in peak power and average power immediately after and for 32 minutes post-treatment. Dorsiflexion was significantly decreased 7 and 12 minutes following treatment. There were no differences for plantar flexion, inversion, or eversion. These data suggest functional performance was affected immediately following and for up to 32 minutes after cold whirlpool treatment. It was also evident that there is a gradual performance increase for each measure of functional performance across time. Therefore, the consequences should be carefully considered before returning athletes to activity following cold whirlpool treatment. Key pointsCryotherapy is a common and highly effective modality in treating acute and chronic athletic injuries.The results indicated that cold whirlpool does have an immediate and subsequent effect on functional performance.Understanding how cold whirlpool adversely affects functional performance allows clinicians to continue using this modality before vigorous athletic activity. PMID:24149907

Environment-Assisted Cracking in Custom 465 Stainless Steel

NASA Astrophysics Data System (ADS)

Lee, E. U.; Goswami, R.; Jones, M.; Vasudevan, A. K.

2011-02-01

The influence of cold work and aging on the environment-assisted cracking (EAC) behavior and mechanical properties of Custom 465 stainless steel (SS) was studied. Four sets of specimens were made and tested. All specimens were initially solution annealed, rapidly cooled, and refrigerated (SAR condition). The first specimen set was steel in the SAR condition. The second specimen set was aged to the H1000 condition. The third specimen set was 60 pct cold worked, and the fourth specimen set was 60 pct cold worked and aged at temperatures ranging from 755 K to 825 K (482 °C to 552 °C) for 4 hours in air. The specimens were subsequently subjected to EAC and mechanical testing. The EAC testing was conducted, using the rising step load (RSL) technique, in aqueous solutions of NaCl of pH 7.3 with concentrations ranging from 0.0035 to 3.5 pct at room temperature. The microstructure, dislocation substructure, and crack paths, resulting from the cold work, aging, or subsequent EAC testing, were examined by optical microscopy, transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The aging of the cold-worked specimens induced carbide precipitation within the martensite lath, but not at the lath or packet boundaries. In the aged specimens, as aging temperature rose, the threshold stress intensity for EAC (KIEAC), elongation, and fracture toughness increased, but the strength and hardness decreased. The KIEAC also decreased with increasing yield strength and NaCl concentration. In the SAR and H1000 specimens, the EAC propagated along the prior austenite grain boundary, while in the cold-worked and cold-worked and aged specimens, the EAC propagated along the martensite lath, and its packet and prior austenite grain boundaries. The controlling mechanism for the observed EAC was identified to be hydrogen embrittlement.

A Comparison of Three-Dimensional Simulations of Traveling-Wave Tube Cold-Test Characteristics Using CST MICROWAVE STUDIO and MAFIA

NASA Technical Reports Server (NTRS)

Chevalier, C. T.; Herrmann, K. A.; Kory, C. L.; Wilson, J. D.; Cross, A. W.; Williams, W. D. (Technical Monitor)

2001-01-01

Previously, it was shown that MAFIA (solutions of Maxwell's equations by the Finite Integration Algorithm), a three-dimensional simulation code, can be used to produce accurate cold-test characteristics including frequency-phase dispersion, interaction impedance, and attenuation for traveling-wave tube (TWT) slow-wave structures. In an effort to improve user-friendliness and simulation time, a model was developed to compute the cold-test parameters using the electromagnetic field simulation software package CST MICROWAVE STUDIO (MWS). Cold-test parameters were calculated for several slow-wave circuits including a ferruled coupled-cavity, a folded waveguide, and a novel finned-ladder circuit using both MWS and MAFIA. Comparisons indicate that MWS provides more accurate cold-test data with significantly reduced simulation times. Both MAFIA and MWS are based on the finite integration (FI) method; however, MWS has several advantages over MAFIA. First, it has a Windows based interface for PC operation, making it very user-friendly, whereas MAFIA is UNIX based. MWS uses a new Perfect Boundary Approximation (PBA), which increases the accuracy of the simulations by avoiding stair step approximations associated with MAFIA's representation of structures. Finally, MWS includes a Visual Basic for Applications (VBA) compatible macro language that enables the simulation process to be automated and allows for the optimization of user-defined goal functions, such as interaction impedance.

Cold Test Operation of the German VEK Vitrification Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fleisch, J.; Schwaab, E.; Weishaupt, M.

2008-07-01

In 2007 the German High-Level Liquid Waste (HLLW) Vitrification plant VEK (Verglasungseinrichtung Karlsruhe) has passed a three months integral cold test operation as final step before entering the hot phase. The overall performance of the vitrification process equipment with a liquid-fed ceramic glass melter as main component proved to be completely in line with the requirements of the regulatory body. The retention efficiency of main radioactive-bearing elements across melter and wet off-gas treatment system exceeded the design values distinctly. The strategy to produce a specified waste glass could be successfully demonstrated. The results of the cold test operation allow enteringmore » the next step of hot commissioning, i.e. processing of approximately 2 m{sup 3} of diluted HLLW. In summary: An important step of the VEK vitrification plant towards hot operation has been the performance of the cold test operation from April to July 2007. This first integral operation was carried out under boundary conditions and rules established for radioactive operation. Operation and process control were carried out following the procedure as documented in the licensed operational manuals. The function of the process technology and the safe operation could be demonstrated. No severe problems were encountered. Based on the positive results of the cold test, application of the license for hot operation has been initiated and is expected in the near future. (authors)« less

Methodes de caracterisation des proprietes thermomecaniques d'un acier martensitique =

NASA Astrophysics Data System (ADS)

Ausseil, Lucas

Le but de l'etude est de developper des methodes permettant de mesurer les proprietes thermomecaniques d'un acier martensitique lors de chauffe rapide. Ces donnees permettent d'alimenter les modeles d'elements finis existant avec des donnees experimentales. Pour cela, l'acier 4340 est utilise. Cet acier est notamment utilise dans les roues d'engrenage, il a des proprietes mecaniques tres interessantes. Il est possible de modifier ses proprietes grâce a des traitements thermiques. Le simulateur thermomecanique Gleeble 3800 est utilise. Il permet de tester theoriquement toutes les conditions presentes dans les procedes de fabrication. Avec les tests de dilatation realises dans ce projet, les temperatures exactes de changement de phases austenitiques et martensitiques sont obtenues. Des tests de traction ont aussi permis de deduire la limite d'elasticite du materiau dans le domaine austenitique allant de 850 °C a 1100 °C. L'effet des deformations sur la temperature de debut de transformation est montre qualitativement. Une simulation numerique est aussi realisee pour comprendre les phenomenes intervenant pendant les essais.

Case histories of bald eagles and other raptors killed by organophosphorus insecticides topically applied to livestock

USGS Publications Warehouse

Henny, C.J.; Kolbe, E.J.; Hill, E.F.; Blus, L.J.

1987-01-01

Since 1982 when secondary poisoning of a red-tailed hawk (Buteo jamaicensis) was documented following the recommended use of famphur applied topically to cattle, the Patuxent Wildlife Research Center has tested dead birds of prey for poisoning by famphur and other pour-on organophosphorus (OP) insecticides. Brain cholinesterase (ChE) activity was first determined, then if ChE was depressed greater than or equal to 50%, stomach and/or crop contents were evaluated for anti-ChE compounds. This report presents the circumstances surrounding the OP-caused deaths of eight bald eagles (Haliaeetus leucocephalus), two red-tailed hawks, and one great horned owl (Bubo virginianus) between March 1984 and March 1985. OP poisoning of raptors by pour-on insecticides in the United States is widespread, but its magnitude is unknown.

Case histories of bald eagles and other raptors killed by organophosphorus insecticides topically applied to livestock.

PubMed

Henny, C J; Kolbe, E J; Hill, E F; Blus, L J

1987-04-01

Since 1982 when secondary poisoning of a red-tailed hawk (Buteo jamaicensis) was documented following the recommended use of famphur applied topically to cattle, the Patuxent Wildlife Research Center has tested dead birds of prey for poisoning by famphur and other pour-on organophosphorus (OP) insecticides. Brain cholinesterase (ChE) activity was first determined, then if ChE was depressed greater than or equal to 50%, stomach and/or crop contents were evaluated for anti-ChE compounds. This report presents the circumstances surrounding the OP-caused deaths of eight bald eagles (Haliaeetus leucocephalus), two red-tailed hawks, and one great horned owl (Bubo virginianus) between March 1984 and March 1985. OP poisoning of raptors by pour-on insecticides in the United States is widespread, but its magnitude is unknown.

8. INTERIOR VIEW, LOOKING WEST, WITH GREY IRON HOLDING FURNACES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. INTERIOR VIEW, LOOKING WEST, WITH GREY IRON HOLDING FURNACES AND AN IRON POUR IN PROCESS, CUPOLA TENDER RICHARD SLAUGHTER SUPERVISING THE POUR. MOLTEN DUCTILE IRON IS POURED FROM THIS 25-TON HOLDING FURNACE INTO LADLES FOR TRANSPORT TO CASTING STATIONS. - Stockham Pipe & Fittings Company, Grey Iron Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

40 CFR 464.35 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year. PSES Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average kg/1,000 kkg (pounds per million pounds) of metal poured Copper (T) 0.0129 0.0071...

Grip force and force sharing in two different manipulation tasks with bottles.

PubMed

Cepriá-Bernal, Javier; Pérez-González, Antonio; Mora, Marta C; Sancho-Bru, Joaquín L

2017-07-01

Grip force and force sharing during two activities of daily living were analysed experimentally in 10 right-handed subjects. Four different bottles, filled to two different levels, were manipulated for two tasks: transporting and pouring. Each test subject's hand was instrumented with eight thin wearable force sensors. The grip force and force sharing were significantly different for each bottle model. Increasing the filling level resulted in an increase in grip force, but the ratio of grip force to load force was higher for lighter loads. The task influenced the force sharing but not the mean grip force. The contributions of the thumb and ring finger were higher in the pouring task, whereas the contributions of the palm and the index finger were higher in the transport task. Mean force sharing among fingers was 30% for index, 29% for middle, 22% for ring and 19% for little finger. Practitioner Summary: We analysed grip force and force sharing in two manipulation tasks with bottles: transporting and pouring. The objective was to understand the effects of the bottle features, filling level and task on the contribution of different areas of the hand to the grip force. Force sharing was different for each task and the bottles features affected to both grip force and force sharing.

Ecological Risks in Residential Premises Arising from Thermal Insulation by Pouring

NASA Astrophysics Data System (ADS)

Timofeeva, S. S.; Timofeev, S. S.

2017-11-01

The residents of modern megacities are exposed to environmental risks arising both directly in the urban environment and their own dwellings. Modern polymeric building materials are the sources of toxic substances release into the air that have a significant impact on the population health. The objective of the work is the ecological and hygienic study of the air in the apartments of Irkutsk after repair work on the roof and walls insulation using the technology of pouring and calculation of the potential environmental risk for the residents. The object of the research was the indoor air in one of the houses in Irkutsk tested for formaldehyde and other toxic substances. After putting the house into operation, some defects were found - the freezing of the walls of the building attic part. During the repair work, the mansard part of the building was heat-insulated by the pouring method using the composite material “Poroplast CF 02”. High concentrations of formaldehyde and styrene were detected in the apartments exceeding the MPC in 4-8 times. The hazard ratio for inhalation exposure to harmful substances exceeds the safety level by 10 times. Consequently, there is a high probability of obtaining acute and chronic poisoning and developing cancer.

Correlation of Wissler Human Thermal Model Blood Flow and Shiver Algorithms

NASA Technical Reports Server (NTRS)

Bue, Grant; Makinen, Janice; Cognata, Thomas

2010-01-01

The Wissler Human Thermal Model (WHTM) is a thermal math model of the human body that has been widely used to predict the human thermoregulatory response to a variety of cold and hot environments. The model has been shown to predict core temperature and skin temperatures higher and lower, respectively, than in tests of subjects in crew escape suit working in a controlled hot environments. Conversely the model predicts core temperature and skin temperatures lower and higher, respectively, than in tests of lightly clad subjects immersed in cold water conditions. The blood flow algorithms of the model has been investigated to allow for more and less flow, respectively, for the cold and hot case. These changes in the model have yielded better correlation of skin and core temperatures in the cold and hot cases. The algorithm for onset of shiver did not need to be modified to achieve good agreement in cold immersion simulations

Efficacy of a heat exchanger mask in cold exercise-induced asthma.

PubMed

Beuther, David A; Martin, Richard J

2006-05-01

To determine the efficacy of a novel mask device in limiting cold air exercise-induced decline in lung function in subjects with a history of exercise-induced asthma (EIA). In spite of appropriate medical therapy, many asthma patients are limited in cold weather activities. In study 1, 13 asthmatic subjects performed two randomized, single-blind treadmill exercise tests while breathing cold air (- 25 to - 15 degrees C) through a placebo or active heat exchanger mask. In study 2, five subjects with EIA performed three treadmill exercise tests while breathing cold air: one test using the heat exchanger mask, one test without the mask but with albuterol pretreatment, and one test with neither the mask nor albuterol pretreatment (unprotected exercise). For all studies, spirometry was performed before and at 5, 15, and 30 min after exercise challenge. For both studies, a total of 15 subjects with a history of asthma symptoms during cold air exercise were recruited. In study 1, the mean decrease (+/- SE) in FEV1 was 19 +/- 4.9% with placebo, and 4.3 +/- 1.6% with the active device (p = 0.0002). The mean decrease in maximum mid-expiratory flow (FEF(25-75)) was 31 +/- 5.7% with placebo and 4.7 +/- 1.7% with the active device (p = 0.0002). In study 2, the mean decrease in FEV1 was 6.3 +/- 3.9%, 11 +/- 3.7%, and 28 +/- 10% for the heat exchanger mask, albuterol pretreatment, and unprotected exercises, respectively (p = 0.4375 for mask vs albuterol, p = 0.0625 for mask vs unprotected exercise). The mean decrease in FEF(25-75) was 10 +/- 4.8%, 23 +/- 6.0%, and 36 +/- 11%, respectively (p = 0.0625 for mask vs albuterol, p = 0.0625 for mask vs unprotected exercise). This heat exchanger mask blocks cold exercise-induced decline in lung function at least as effectively as albuterol pretreatment.

Behavioral and anatomical characterization of the bilateral sciatic nerve chronic constriction (bCCI) injury: correlation of anatomic changes and responses to cold stimuli

PubMed Central

2010-01-01

Background Unilateral constrictive sciatic nerve injury (uCCI) is a common neuropathic pain model. However, the bilateral constrictive injury (bCCI) model is less well studied, and shows unique characteristics. In the present study, we sought to correlate effects of bCCI on nocifensive responses to cold and mechanical stimuli with selected dorsal horn anatomic markers. bCCI or sham ligation of both rat sciatic nerves were followed up to 90 days of behavioural testing. Additional rats sacrificed at 15, 30 and 90 days were used for anatomic analyses. Behavioural tests included hindpaw withdrawal responses to topical acetone, cold plate testing, an operant thermal preference task and hindpaw withdrawal thresholds to mechanical probing. Results All nocifensive responses to cold increased and remained enhanced for >45 days. Mechanical withdrawal thresholds decreased for 25 days only. Densitometric analyses of immunoperoxidase staining in the superficial dorsal horn at L4-5 revealed decreased cholecystokinin (CCK) staining at all times after bCCI, decreased mu opiate receptor (MOR) staining, maximal at 15 days, increased neuropeptide Y (NPY) staining only at days 15 and 30, and increased neurokinin-1 receptor (NK-1R) staining at all time points, maximal at 15 days. Correlation analyses at 45 days post-bCCI, were significant for individual rat nocifensive responses in each cold test and CCK and NK-1R, but not for MOR or NPY. Conclusions These results confirm the usefulness of cold testing in bCCI rats, a new approach using CCI to model neuropathic pain, and suggest a potential value of studying the roles of dorsal horn CCK and substance P in chronic neuropathic pain. Compared to human subjects with neuropathic pain, responses to cold stimuli in rats with bCCI may be a useful model of neuropathic pain. PMID:20105332

Behavioral and anatomical characterization of the bilateral sciatic nerve chronic constriction (bCCI) injury: correlation of anatomic changes and responses to cold stimuli.

PubMed

Datta, Sukdeb; Chatterjee, Koel; Kline, Robert H; Wiley, Ronald G

2010-01-27

Unilateral constrictive sciatic nerve injury (uCCI) is a common neuropathic pain model. However, the bilateral constrictive injury (bCCI) model is less well studied, and shows unique characteristics. In the present study, we sought to correlate effects of bCCI on nocifensive responses to cold and mechanical stimuli with selected dorsal horn anatomic markers. bCCI or sham ligation of both rat sciatic nerves were followed up to 90 days of behavioural testing. Additional rats sacrificed at 15, 30 and 90 days were used for anatomic analyses. Behavioural tests included hindpaw withdrawal responses to topical acetone, cold plate testing, an operant thermal preference task and hindpaw withdrawal thresholds to mechanical probing. All nocifensive responses to cold increased and remained enhanced for >45 days. Mechanical withdrawal thresholds decreased for 25 days only. Densitometric analyses of immunoperoxidase staining in the superficial dorsal horn at L4-5 revealed decreased cholecystokinin (CCK) staining at all times after bCCI, decreased mu opiate receptor (MOR) staining, maximal at 15 days, increased neuropeptide Y (NPY) staining only at days 15 and 30, and increased neurokinin-1 receptor (NK-1R) staining at all time points, maximal at 15 days. Correlation analyses at 45 days post-bCCI, were significant for individual rat nocifensive responses in each cold test and CCK and NK-1R, but not for MOR or NPY. These results confirm the usefulness of cold testing in bCCI rats, a new approach using CCI to model neuropathic pain, and suggest a potential value of studying the roles of dorsal horn CCK and substance P in chronic neuropathic pain. Compared to human subjects with neuropathic pain, responses to cold stimuli in rats with bCCI may be a useful model of neuropathic pain.

Comparative analysis of the cold acclimation and freezing tolerance capacities of seven diploid Brachypodium distachyon accessions

PubMed Central

Colton-Gagnon, Katia; Ali-Benali, Mohamed Ali; Mayer, Boris F.; Dionne, Rachel; Bertrand, Annick; Do Carmo, Sonia; Charron, Jean-Benoit

2014-01-01

Background and Aims Cold is a major constraint for cereal cultivation under temperate climates. Winter-hardy plants interpret seasonal changes and can acquire the ability to resist sub-zero temperatures. This cold acclimation process is associated with physiological, biochemical and molecular alterations in cereals. Brachypodium distachyon is considered a powerful model system to study the response of temperate cereals to adverse environmental conditions. To date, little is known about the cold acclimation and freezing tolerance capacities of Brachypodium. The main objective of this study was to evaluate the cold hardiness of seven diploid Brachypodium accessions. Methods An integrated approach, involving monitoring of phenological indicators along with expression profiling of the major vernalization regulator VRN1 orthologue, was followed. In parallel, soluble sugars and proline contents were determined along with expression profiles of two COR genes in plants exposed to low temperatures. Finally, whole-plant freezing tests were performed to evaluate the freezing tolerance capacity of Brachypodium. Key Results Cold treatment accelerated the transition from the vegetative to the reproductive phase in all diploid Brachypodium accessions tested. In addition, low temperature exposure triggered the gradual accumulation of BradiVRN1 transcripts in all accessions tested. These accessions exhibited a clear cold acclimation response by progressively accumulating proline, sugars and COR gene transcripts. However, whole-plant freezing tests revealed that these seven diploid accessions only have a limited capacity to develop freezing tolerance when compared with winter varieties of temperate cereals such as wheat and barley. Furthermore, little difference in terms of survival was observed among the accessions tested despite their previous classification as either spring or winter genotypes. Conclusions This study is the first to characterize the freezing tolerance capacities of B. distachyon and provides strong evidence that some diploid accessions such as Bd21 have a facultative growth habit. PMID:24323247

Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter: Summary of FY2016 experiements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K.; Fowley, M.; Miller, D.

2016-12-01

Five experiments were completed with the full-scale, room temperature Hanford Waste Treatment and Immobilization Plant (WTP) high-level waste (HLW) melter riser test system to observe particle flow and settling in support of a crystal tolerant approach to melter operation. A prototypic pour rate was maintained based on the volumetric flow rate. Accumulation of particles was observed at the bottom of the riser and along the bottom of the throat after each experiment. Measurements of the accumulated layer thicknesses showed that the settled particles at the bottom of the riser did not vary in thickness during pouring cycles or idle periods.more » Some of the settled particles at the bottom of the throat were re-suspended during subsequent pouring cycles, and settled back to approximately the same thickness after each idle period. The cause of the consistency of the accumulated layer thicknesses is not year clear, but was hypothesized to be related to particle flow back to the feed tank. Additional experiments reinforced the observation of particle flow along a considerable portion of the throat during idle periods. Limitations of the system are noted in this report and may be addressed via future modifications. Follow-on experiments will be designed to evaluate the impact of pouring rate on particle re-suspension, the influence of feed tank agitation on particle accumulation, and the effect of changes in air lance positioning on the accumulation and re-suspension of particles at the bottom of the riser. A method for sampling the accumulated particles will be developed to support particle size distribution analyses. Thicker accumulated layers will be intentionally formed via direct addition of particles to select areas of the system to better understand the ability to continue pouring and re-suspend particles. Results from the room temperature system will be correlated with observations and data from the Research Scale Melter (RSM) at Pacific Northwest National Laboratory, and coordinated with modeling efforts underway at Idaho National Laboratory.« less

Toxicity of Cold Lake Blend and Western Canadian Select dilbits to standard aquatic test species

EPA Science Inventory

Dilbits are blends of bitumen and natural gas condensates or crude oils with only limited toxicity data. Two dilbits, Cold Lake Blend and Western Canadian Select, were tested as either unweathered or weathered oils for acute and chronic toxicity to standard freshwater and estuari...

Cold Spray Technology for Repair of Magnesium Rotorcraft Components (Briefing Charts)

DTIC Science & Technology

2007-01-01

control valve Nozzle Braided flex hose Helium Tank Powder Feeder Spray Nozzle ARL Portable System Parameters for Applying CP-Al to ZE41A - Mg...and Advantages of Cold Spray •Present Test Results to Date •Coating Integrity and Microstructural Analysis •Adhesion, Hardness and Corrosion Tests

Cold in-place recycling using solventless emulsion - phase IV (emulsion qualification and long-term field performance).

DOT National Transportation Integrated Search

2016-05-01

This report looks into how a successful Cold In-Place solventless emulsion behaves and how the emulsion : break test developed in Phase III of this project demonstrates that behavior. Modifications to the test have been : made to improve the consiste...

Primary acquired cold urticaria.

PubMed

Lee, Chyh-Woei; Sheffer, Albert L

2003-01-01

Primary acquired cold urticaria (ACU) is the most common type of cold urticaria characterized by rapid onset of pruritic hives, swelling, and possible severe systemic reactions including hypotension and shock after cold exposure. Primary ACU is diagnosed by history of such symptoms, a positive immediate cold-contact stimulation test, and negative laboratory evaluation for underlying systemic disorders. Clinicians should be aware that patients with ACU may be susceptible to life-threatening systemic reactions especially during aquatic activities and that proper patient education is extremely important. This article reviews the clinical presentation, pathogenesis, diagnosis, and management of primary ACU.

Early sign of microangiopathy in systemic sclerosis: The significance of cold stress test in dynamic laser Doppler flowmetry.

PubMed

Yu, Sebastian; Hu, Stephen Chu-Sung; Yu, Hsin-Su; Chin, Yi-Ying; Cheng, Yang-Chun; Lee, Chih-Hung

2018-06-05

Skin physiology measurement is receiving more attention for detecting vasculopathy in systemic sclerosis (SSc). Laser Doppler flowmetry (LDF) is a widely used physiological measurement to assess cutaneous microcirculation. However, findings of LDF may be normal during early stage of microangiopathy in SSc. We hypothesized that cold stress test combined with LDF could detect early-stage microangiopathy in patients with SSc. A 67-year-old male came with multiple ulcerations on his fingers for one year. After excluding diseases such as diabetes mellitus-related peripheral arterial occlusive disease and smoking-related Buerger's disease, the diagnosis of SSc was made according to the 2013 ACR/EULAR criteria. We performed LDF and angiography for a patient with SSc and compared the results. Although occlusions of right ulnar and digital arteries were obvious in angiography, the baseline skin temperature and perfusion unit on right fingers remained within normal limits. While the microcirculatory abnormalities measured by LDF alone are subtle, LDF combined with cold stress test detected a significant slow recovery of skin blood flow 40 minutes after cold immersion. In conclusion, there may be discordance between macrovasculopathy and baseline microcirculatory blood flow in SSc. In such a case, cold immersion test is essential to measure the dynamic change and slow recovery of blood flow.

Performance, Physiological, and Acceptance Tests of a 1500 KCAL emergency/Assault Food Packet Diet in a Cold Weather Environment

DTIC Science & Technology

1980-11-01

acket (E/AP) and to assess performance and physiological effects of t he ration at two different ca loric levels. During a f ive-day exercise in a...PACKET FIELD FEEDING RAT IONS DIET(S) PHYSIOLOG ICAL EMERGENCY RATIONS COMPRESSED FOODS TESTS FREEZE DRIED FOODS COLD WEATH ER PERFORMANCE...cold-weather climate, one group of Marines was issued the standard C ration (3550 kca l) while half of a second group were issued one E/AP per day

Methode d'identification parametrique pour la surveillance in situ des joints a recouvrement par propagation d'ondes vibratoires

NASA Astrophysics Data System (ADS)

Francoeur, Dany

Cette these de doctorat s'inscrit dans le cadre de projets CRIAQ (Consortium de recherche et d'innovation en aerospatiale du Quebec) orientes vers le developpement d'approches embarquees pour la detection de defauts dans des structures aeronautiques. L'originalite de cette these repose sur le developpement et la validation d'une nouvelle methode de detection, quantification et localisation d'une entaille dans une structure de joint a recouvrement par la propagation d'ondes vibratoires. La premiere partie expose l'etat des connaissances sur l'identification d'un defaut dans le contexte du Structural Health Monitoring (SHM), ainsi que la modelisation de joint a recouvrements. Le chapitre 3 developpe le modele de propagation d'onde d'un joint a recouvrement endommage par une entaille pour une onde de flexion dans la plage des moyennes frequences (10-50 kHz). A cette fin, un modele de transmission de ligne (TLM) est realise pour representer un joint unidimensionnel (1D). Ce modele 1D est ensuite adapte a un joint bi-dimensionnel (2D) en faisant l'hypothese d'un front d'onde plan incident et perpendiculaire au joint. Une methode d'identification parametrique est ensuite developpee pour permettre a la fois la calibration du modele du joint a recouvrement sain, la detection puis la caracterisation de l'entaille situee sur le joint. Cette methode est couplee a un algorithme qui permet une recherche exhaustive de tout l'espace parametrique. Cette technique permet d'extraire une zone d'incertitude reliee aux parametres du modele optimal. Une etude de sensibilite est egalement realisee sur l'identification. Plusieurs resultats de mesure sur des joints a recouvrements 1D et 2D sont realisees permettant ainsi l'etude de la repetabilite des resultats et la variabilite de differents cas d'endommagement. Les resultats de cette etude demontrent d'abord que la methode de detection proposee est tres efficace et permet de suivre la progression d'endommagement. De tres bons resultats de quantification et de localisation d'entailles ont ete obtenus dans les divers joints testes (1D et 2D). Il est prevu que l'utilisation d'ondes de Lamb permettraient d'etendre la plage de validite de la methode pour de plus petits dommages. Ces travaux visent d'abord la surveillance in-situ des structures de joint a recouvrements, mais d'autres types de defauts. (comme les disbond) et. de structures complexes sont egalement envisageables. Mots cles : joint a recouvrement, surveillance in situ, localisation et caracterisation de dommages

Impact of cold temperature on Euro 6 passenger car emissions.

PubMed

Suarez-Bertoa, Ricardo; Astorga, Covadonga

2018-03-01

Hydrocarbons, CO, NOx, NH 3 , N 2 O, CO 2 and particulate matter emissions affect air quality, global warming and human health. Transport sector is an important source of these pollutants and high pollution episodes are often experienced during the cold season. However, EU vehicle emissions regulation at cold ambient temperature only addresses hydrocarbons and CO vehicular emissions. For that reason, we have studied the impact that cold ambient temperatures have on Euro 6 diesel and spark ignition (including: gasoline, ethanol flex-fuel and hybrid vehicles) vehicle emissions using the World-harmonized Light-duty Test Cycle (WLTC) at -7 °C and 23 °C. Results indicate that when facing the WLTC at 23 °C the tested vehicles present emissions below the values set for type approval of Euro 6 vehicles (still using NEDC), with the exception of NOx emissions from diesel vehicles that were 2.3-6 times higher than Euro 6 standards. However, emissions disproportionally increased when vehicles were tested at cold ambient temperature (-7 °C). High solid particle number (SPN) emissions (>1 × 10 11 # km -1 ) were measured from gasoline direct injection (GDI) vehicles and gasoline port fuel injection vehicles. However, only diesel and GDI SPN emissions are currently regulated. Results show the need for a new, technology independent, procedure that enables the authorities to assess pollutant emissions from vehicles at cold ambient temperatures. Harmful pollutant emissions from spark ignition and diesel vehicles are strongly and negatively affected by cold ambient temperatures. Only hydrocarbon, CO emissions are currently regulated at cold temperature. Therefore, it is of great importance to revise current EU winter vehicle emissions regulation. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Characterizing convective cold pools: Characterizing Convective Cold Pools

DOE PAGES

Drager, Aryeh J.; van den Heever, Susan C.

2017-05-09

Cold pools produced by convective storms play an important role in Earth's climate system. However, a common framework does not exist for objectively identifying convective cold pools in observations and models. The present study investigates convective cold pools within a simulation of tropical continental convection that uses a cloud-resolving model with a coupled land-surface model. Multiple variables are assessed for their potential in identifying convective cold pool boundaries, and a novel technique is developed and tested for identifying and tracking cold pools in numerical model simulations. This algorithm is based on surface rainfall rates and radial gradients in the densitymore » potential temperature field. The algorithm successfully identifies near-surface cold pool boundaries and is able to distinguish between connected cold pools. Once cold pools have been identified and tracked, composites of cold pool evolution are then constructed, and average cold pool properties are investigated. Wet patches are found to develop within the centers of cold pools where the ground has been soaked with rainwater. These wet patches help to maintain cool surface temperatures and reduce cold pool dissipation, which has implications for the development of subsequent convection.« less

Characterizing convective cold pools: Characterizing Convective Cold Pools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Drager, Aryeh J.; van den Heever, Susan C.

Cold pools produced by convective storms play an important role in Earth's climate system. However, a common framework does not exist for objectively identifying convective cold pools in observations and models. The present study investigates convective cold pools within a simulation of tropical continental convection that uses a cloud-resolving model with a coupled land-surface model. Multiple variables are assessed for their potential in identifying convective cold pool boundaries, and a novel technique is developed and tested for identifying and tracking cold pools in numerical model simulations. This algorithm is based on surface rainfall rates and radial gradients in the densitymore » potential temperature field. The algorithm successfully identifies near-surface cold pool boundaries and is able to distinguish between connected cold pools. Once cold pools have been identified and tracked, composites of cold pool evolution are then constructed, and average cold pool properties are investigated. Wet patches are found to develop within the centers of cold pools where the ground has been soaked with rainwater. These wet patches help to maintain cool surface temperatures and reduce cold pool dissipation, which has implications for the development of subsequent convection.« less

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2010 CFR

2010-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2014 CFR

2014-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2012 CFR

2012-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2011 CFR

2011-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2013 CFR

2013-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

Developpement d'un catalyseur nickel-alumine efficace pour le reformage de diesel a la vapeur d'eau et etude du systeme reactionnel

NASA Astrophysics Data System (ADS)

Fauteux-Lefebvre, Clemence

Le developpement de sources d'energie alternatives fiables et efficaces est aujourd'hui une necessite. L' interet dans le reformage d'hydrocarbures liquides est ainsi croissant puisqu'il s'agit d'une voie pour l'alimentation des piles a combustible. Les piles a combustible ont une efficacite pour la conversion d'energie en electricite plus grande que celle des moteurs a combustion et font ainsi partie de la recherche de solution en efficacite energetique. Ces piles consomment de l'hydrogene comme combustible pour produire de l'electricite, d'ou l'interet pour le reformage. En effet, cette reaction permet de produire de l'hydrogene et du monoxyde de carbone (un autre combustible des piles a combustible a electrolyte solide) a partir d'hydrocarbure liquide, notamment le diesel. Les piles pourraient donc etre integrees avec une unite de reformage leur fournissant directement le combustible necessaire a partir de diesel. Dans ce projet de recherche, un nouveau catalyseur de nickel sous forme de spinelle nickel-alumine (spinelle NiAl2O4 sur support d'alumine et de zircone stabilisee avec yttria) a ete developpe et teste en laboratoire pour du reformage de propane, d'hydrocarbures liquides et de diesel, a la vapeur d'eau. Par ailleurs, une methode d'ajout des reactifs novatrice a ete utilisee afin de diminuer la pyrolyse precedant le reformage, en utilisant une emulsion. Les resultats de reformage d'hydrocarbures purs ont montre des concentrations tres pres de l'equilibre thermodynamique et une activite constante sans desactivation du catalyseur ni formation de carbone, et ce avec des ratios H2O/C de moins de 2.5 et des temperatures d'operation variant entre 630 °C et 750 °C. Lors de tests effectues en utilisant du diesel fossile, a 705°C, avec un debit volumique des reactifs de plus de 50 000 cm3gcat-1h-1 et un ratio H2O/C de moins de 2.5, l'activite a ete maintenue pendant plus de 15 heures, malgre une operation en cycles. L'analyse du catalyseur apres cette utilisation n'a montre aucun carbone significatif sur la surface.- En comparaison, un catalyseur de nickel metallique sur support d'Al2O3 et YSZ a ete utilise dans des conditions similaires. Il y a eu desactivation du catalyseur et obstruction du reacteur par du carbone apres trois heures d'operation. L'analyse de ce catalyseur a permis de verifier qu'il etait recouvert de carbone en filament. L'analyse du systeme reactionnel a montre que la reaction est controlee par la reaction de. surface et non par le transfert de masse. Par ailleurs, les analyses des catalyseurs de spinelle ont demontre qu'il n'y avait pas de modification de sa forme chimique ni de reduction du spinelle en nickel metallique apres l'utilisation. Mots cles : Reformage a la vapeur, diesel, hydrocarbure liquide, catalyseur, spinelle nickel-alumine, equilibre thermodynamique

Synthesis copolymer use to reduce pour point temperature of diamond crude oil

NASA Astrophysics Data System (ADS)

Than, Dao Viet; Chuong, Thai Hong; Tuy, Dao Quoc

2017-09-01

Diamond oil field is located in Block 01&02 Offshore Vietnam. Crude oil from Diamond Well Head Platform (WHP) is evacuated to FPSO via 20km 10" subsea flexible pipeline. The lowest seabed temperature in the field is 22°C, while the pour point temperature (PPT) of Diamond crude oil is very high (36°C) due to high paraffin content (25%). So studying to research a suitable Pour Point Depressant (PPD) for the crude oil is very important. The PPD must have ability to reduce pour point temperature of crude oil from 36°C to 21°C.

Evaluation of vaccine cold chain in urban health centers of municipal corporation of surat city, Western India.

PubMed

Naik, Ashish K; Rupani, Mihir P; Bansal, R K

2013-12-01

The success of immunization depends highly on the level of cold chain maintenance. The aim of the study was to assess the condition of cold chain equipment, practices adopted for cold chain maintenance and knowledge of the vaccinators. It was a cross-sectional study conducted in 20 UHCs of Surat Municipal Corporation (SMC). Cold chain equipment were observed with regards to their condition, along with the practices adopted by vaccinators for cold chain maintenance. A pre-designed and pre-tested questionnaire was used to interview the vaccinators regarding their knowledge and awareness regarding cold chain practices, management and handling. Data were entered and analyzed using Epi Info v 3.5.1. Simple proportions were calculated. Absence of separate stabilizer for deep freezers and ILRs (85%), ill-maintained temperature-record register, lack of criss-cross pattern of ice packs in deep freezer (65%), presence of things other than ice packs in deep freezer (10%) and things other than vaccines in ILR (10%) indicate poor cold chain maintenance. In addition to this, expired vaccines in ILR (5%), vaccines in the "unusable" stages of VVM (15%), lack of emergency contact number nearby in case of cold chain failure (85%), lack of inverter (85%), lack of generator (85%) and failure to note time of reconstitution on the vaccine vial at the time of vaccination (25%) indicate poor cold chain practices. Lack of knowledge of defrosting of ILR and deep freezer (45%), lack of knowledge about Shake test (40%), lack of knowledge of temperature range to be maintained in deep freezer (70%) and in ILR (15%) indicate poor knowledge of vaccinators. Cold chain maintenance and practices need improvement. Knowledge of vaccinators was overall unsatisfactory.

Polymorphic ventricular tachycardia due to variant angina diagnosed on Holter monitoring and confirmed with cold pressor test.

PubMed

Öztürk, Semi; Aktemur, Tuğba; Kalyoncuoğlu, Muhsin; Durmuş, Gündüz; Can, Mehmet

2017-04-01

A 52-year-old man complaining of persistent recurring chest pain at night underwent coronary angiogram at another institution. Normal coronaries were observed and he was discharged with muscle spasmolytic prescription. Since symptoms had continued, 24-hour Holter monitoring was ordered at our facility and results revealed huge ST elevation and polymorphic ventricular tachycardia. Cold pressor test performed in catheterization laboratory also resulted in ventricular tachycardia. Nifedipine was prescribed and follow-up Holter monitoring revealed no further vasospastic episodes. Utility of 24-hour Holter rhythm monitoring and cold pressor test in patients with recurrent chest pain at night is demonstrated in this report.

Design verification and cold-flow modeling test report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-07-01

This report presents a compilation of the following three test reports prepared by TRW for Alaska Industrial Development and Export Authority (AIDEA) as part of the Healy Clean Coal Project, Phase 1 Design of the TRW Combustor and Auxiliary Systems, which is co-sponsored by the Department of Energy under the Clean Coal Technology 3 Program: (1) Design Verification Test Report, dated April 1993, (2) Combustor Cold Flow Model Report, dated August 28, 1992, (3) Coal Feed System Cold Flow Model Report, October 28, 1992. In this compilation, these three reports are included in one volume consisting of three parts, andmore » TRW proprietary information has been excluded.« less

Nationalism, Nuclear Policy and Children in Cold War America.

ERIC Educational Resources Information Center

Stephens, Sharon

1997-01-01

Theorizes the place of children in America's "Cold War Consensus" of the 1950s-60s. Counterposes dominant Cold War images of abstract, generic children (inevitably white middle class) to actual children most vulnerable to risks associated with nuclear weapons production and testing. Concludes that in various ways, these children were all…

Cold Helium Pressurization for Liquid Oxygen / Liquid Methane Propulsion Systems: Fully-Integrated Initial Hot-Fire Test Results

NASA Technical Reports Server (NTRS)

Morehead, R. L.; Atwell, M. J.; Melcher, J. C.; Hurlbert, E. A.

2016-01-01

A prototype cold helium active pressurization system was incorporated into an existing liquid oxygen (LOX) / liquid methane (LCH4) prototype planetary lander and hot-fire tested to collect vehicle-level performance data. Results from this hot-fire test series were used to validate integrated models of the vehicle helium and propulsion systems and demonstrate system effectiveness for a throttling lander. Pressurization systems vary greatly in complexity and efficiency between vehicles, so a pressurization performance metric was also developed as a means to compare different active pressurization schemes. This implementation of an active repress system is an initial sizing draft. Refined implementations will be tested in the future, improving the general knowledge base for a cryogenic lander-based cold helium system.

Thermal math model analysis of FRSI test article subjected to cold soak and entry environments. [Flexible Reuseable Surface Insulation in Space Shuttle Orbiter

NASA Technical Reports Server (NTRS)

Gallegos, J. J.

1978-01-01

A multi-objective test program was conducted at the NASA/JSC Radiant Heat Test Facility in which an aluminum skin/stringer test panel insulated with FRSI (Flexible Reusable Surface Insulation) was subjected to 24 simulated Space Shuttle Orbiter ascent/entry heating cycles with a cold soak in between in the 10th and 20th cycles. A two-dimensional thermal math model was developed and utilized to predict the thermal performance of the FRSI. Results are presented which indicate that the modeling techniques and property values have been proven adequate in predicting peak structure temperatures and entry thermal responses from both an ambient and cold soak condition of an FRSI covered aluminum structure.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denslow, Kayte M.; Bontha, Jagannadha R.; Adkins, Harold E.

This document presents the visual and ultrasonic PulseEcho critical velocity test results obtained from the System Performance test campaign that was completed in September 2012 with the Remote Sampler Demonstration (RSD)/Waste Feed Flow Loop cold-test platform located at the Monarch test facility in Pasco, Washington. This report is intended to complement and accompany the report that will be developed by WRPS on the design of the System Performance simulant matrix, the analysis of the slurry test sample concentration and particle size distribution (PSD) data, and the design and construction of the RSD/Waste Feed Flow Loop cold-test platform.

A Selection of Experimental Test Cases for the Validation of CFD Codes (Recueil de cas d’essai experimentaux pour la validation des codes de l’aerodynamique numerique). Volume 1

DTIC Science & Technology

1994-08-01

volume H1. Le rapport ext accompagnt5 doun jeo die disqoettex contenant les donn~es appropri~es Li bous let cas d’essai. (’es disqoettes sont disponibles ...GERMANY PURPL’Sb OF THE TESi The tests are part of a larger effort to establish a database of experimental measurements for missile configurations

L'effet de la superoxyde dismutase sur le système nerveux central irradié à propos d'études pilotes expérimentales chez le rat

NASA Astrophysics Data System (ADS)

Baillet, F.; Lamproglou, I.; Boisserie, G.

1998-04-01

It has been observed that bovine superoxide dismutase (SOD) can reduce some chronic complications due to radiotherapy. For this reason this enzyme has been used in the rat to treat radiation induced encaphalitis, studied by the two-way avoidance test. SOD has allowed significant regression of troubles in two studies with chronic encephalitis and two studies with acute encephalitis. Moreover, another study has shown that SOD prevented cognitival troubles brought on by strong painful stimulus. Thus SOD has been shown able to improve cerebral performances after a specific aggression (after radiotherapy) or after a non specific one (after very painful stimulus). This observation leads to interesting prospects for therapy. Il a été constaté que la superoxyde dismutase bovine (SOD) pouvait faire régresser certaines complications chroniques de la radiothérapie. Pour cette raison cette enzyme a été utilisée chez le rat pour traiter des encéphalites radiques étudiées par le test de l'évitement actif bilatéral. La SOD a permis une régression significative des troubles dans deux études d'encéphalite chronique et deux études d'encéphalite aiguë. Par ailleurs une autre étude a montré que la SOD prévenait les troubles cognitifs engendrés par un stimulus douloureux important. Ainsi la SOD s'est révélée capable d'améliorer les performances cérébrales après une agression spécifique (radiothérapie) ou non spécifique (stimulus douloureux important). Cette constatation ouvre des perspectives intéressantes pour la thérapeutique.

Thermodynamic Behavior Research Analysis of Twin-roll Casting Lead Alloy Strip Process

NASA Astrophysics Data System (ADS)

Jiang, Chengcan; Rui, Yannian

2017-03-01

The thermodynamic behavior of twin-roll casting (TRC) lead alloy strip process directly affects the forming of the lead strip, the quality of the lead strip and the production efficiency. However, there is little research on the thermodynamics of lead alloy strip at home and abroad. The TRC lead process is studied in four parameters: the pouring temperature of molten lead, the depth of molten pool, the roll casting speed, and the rolling thickness of continuous casting. Firstly, the thermodynamic model for TRC lead process is built. Secondly, the thermodynamic behavior of the TRC process is simulated with the use of Fluent. Through the thermodynamics research and analysis, the process parameters of cast rolling lead strip can be obtained: the pouring temperature of molten lead: 360-400 °C, the depth of molten pool: 250-300 mm, the roll casting speed: 2.5-3 m/min, the rolling thickness: 8-9 mm. Based on the above process parameters, the optimal parameters(the pouring temperature of molten lead: 375-390 °C, the depth of molten pool: 285-300 mm, the roll casting speed: 2.75-3 m/min, the rolling thickness: 8.5-9 mm) can be gained with the use of the orthogonal experiment. Finally, the engineering test of TRC lead alloy strip is carried out and the test proves the thermodynamic model is scientific, necessary and correct. In this paper, a detailed study on the thermodynamic behavior of lead alloy strip is carried out and the process parameters of lead strip forming are obtained through the research, which provide an effective theoretical guide for TRC lead alloy strip process.

Test Methodologies for Personal Protective Equipment Against Anti-Personnel Mine Blast (Methodologies d’essais pour le materiel de protection prsonnel contre le souffle produit par les mines antipersonnel)

DTIC Science & Technology

2004-03-01

probabilistic by design. Finally, as the fragments disperse, fragment density decreases, and the probability of a fragment strike drops rapidly. Given the...Any PPE subjected to such testing needs to be exposed repeatedly to several mines in order to obtain a sufficient number of strikes . This will allow...velocity of each fragment, and the location of fragment strikes cannot be controlled precisely. This means that the same test must be repeated a

2015 Groundwater Radiological Monitoring Results Associated with the Advanced Test Reactor Complex Cold Waste Ponds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, Michael George

This report summarizes radiological monitoring results from groundwater wells associated with the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Ponds Reuse Permit (I-161-02). All radiological monitoring is performed to fulfill Department of Energy requirements under the Atomic Energy Act.

Fluid Structure Interaction in a Cold Flow Test and Transient CFD Analysis of Out-of-Round Nozzles

NASA Technical Reports Server (NTRS)

Ruf, Joseph; Brown, Andrew; McDaniels, David; Wang, Ten-See

2010-01-01

This viewgraph presentation describes two nozzle fluid flow interactions. They include: 1) Cold flow nozzle tests with fluid-structure interaction at nozzle separated flow; and 2) CFD analysis for nozzle flow and side loads of nozzle extensions with various out-of-round cases.

Reactor Simulator Testing

NASA Technical Reports Server (NTRS)

Schoenfeld, Michael P.; Webster, Kenny L.; Pearson, Boise Jon

2013-01-01

As part of the Nuclear Systems Office Fission Surface Power Technology Demonstration Unit (TDU) project, a reactor simulator test loop (RxSim) was design & built to perform integrated testing of the TDU components. In particular, the objectives of RxSim testing was to verify the operation of the core simulator, the instrumentation and control system, and the ground support gas and vacuum test equipment. In addition, it was decided to include a thermal test of a cold trap purification design and a pump performance test at pump voltages up to 150 V since the targeted mass flow rate of 1.75 kg/s was not obtained in the RxSim at the originally constrained voltage of 120 V. This paper summarizes RxSim testing. The gas and vacuum ground support test equipment performed effectively in NaK fill, loop pressurization, and NaK drain operations. The instrumentation and control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings. The cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained which was lower than the predicted 750 K but 156 K higher than the cold temperature indicating the design provided some heat regeneration. The annular linear induction pump (ALIP) tested was able to produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz. Keywords: fission, space power, nuclear, liquid metal, NaK.

Impact of suggestion on the human experimental model of cold hyperalgesia after topical application of high-concentration menthol [40%].

PubMed

Helfert, S; Reimer, M; Barnscheid, L; Hüllemann, P; Rengelshausen, J; Keller, T; Baron, R; Binder, A

2018-05-14

Human experimental pain models in healthy subjects offer unique possibilities to study mechanisms of pain within a defined setting of expected pain symptoms, signs and mechanisms. Previous trials in healthy subjects demonstrated that topical application of 40% menthol is suitable to induce cold hyperalgesia. The objective of this study was to evaluate the impact of suggestion on this experimental human pain model. The study was performed within a single-centre, randomized, placebo-controlled, double-blind, two-period crossover trial in a cohort of 16 healthy subjects. Subjects were tested twice after topical menthol application (40% dissolved in ethanol) and twice after ethanol (as placebo) application. In the style of a balanced placebo trial design, the subjects received during half of the testing the correct information about the applied substance (topical menthol or ethanol) and during half of the testing the incorrect information, leading to four tested conditions (treatment conditions: menthol-told-menthol and menthol-told-ethanol; placebo conditions: ethanol-told-menthol and ethanol-told-ethanol). Cold but not mechanical hyperalgesia was reliably induced by the model. The cold pain threshold decreased in both treatment conditions regardless whether true or false information was given. Minor suggestion effects were found in subjects with prior ethanol application. The menthol model is a reliable, nonsuggestible model to induce cold hyperalgesia. Mechanical hyperalgesia is not as reliable to induce. Cold hyperalgesia may be investigated under unbiased and suggestion-free conditions using the menthol model of pain. © 2018 European Pain Federation - EFIC®.

Phenol degradation and heavy metal tolerance of Antarctic yeasts.

PubMed

Fernández, Pablo Marcelo; Martorell, María Martha; Blaser, Mariana G; Ruberto, Lucas Adolfo Mauro; de Figueroa, Lucía Inés Castellanos; Mac Cormack, Walter Patricio

2017-05-01

In cold environments, biodegradation of organic pollutants and heavy metal bio-conversion requires the activity of cold-adapted or cold-tolerant microorganisms. In this work, the ability to utilize phenol, methanol and n-hexadecane as C source, the tolerance to different heavy metals and growth from 5 to 30 °C were evaluated in cold-adapted yeasts isolated from Antarctica. Fifty-nine percent of the yeasts were classified as psychrotolerant as they could grow in all the range of temperature tested, while the other 41% were classified as psychrophilic as they only grew below 25 °C. In the assimilation tests, 32, 78, and 13% of the yeasts could utilize phenol, n-hexadecane, and methanol as C source, respectively, but only 6% could assimilate the three C sources evaluated. In relation to heavy metals ions, 55, 68, and 80% were tolerant to 1 mM of Cr(VI), Cd(II), and Cu(II), respectively. Approximately a half of the isolates tolerated all of them. Most of the selected yeasts belong to genera previously reported as common for Antarctic soils, but several other genera were also isolated, which contribute to the knowledge of this cold environment mycodiversity. The tolerance to heavy metals of the phenol-degrading cold-adapted yeasts illustrated that the strains could be valuable as inoculant for cold wastewater treatment in extremely cold environments.

Cutaneous microvascular response during local cold exposure - the effect of female sex hormones and cold perception.

PubMed

Cankar, Ksenija; Music, Mark; Finderle, Zare

2016-11-01

It is generally known that differences exist between males and females with regard to sensitivity to cold. Similar differences even among females in different hormonal balance might influence microvascular response during cold provocation testing. The aim of the present study was to measure sex hormone levels, cold and cold pain perception thresholds and compare them to cutaneous laser-Doppler flux response during local cooling in both the follicular and luteal phases of the menstrual cycle. In the luteal phase a more pronounced decrease in laser-Doppler flux was observed compared to follicular phase during local cooling at 15°C (significant difference by Dunnett's test, p<0.05). In addition, statistically significant correlations between progesterone level and laser-Doppler flux response to local cooling were observed during the follicular (R=-0.552, p=0.0174) and during the luteal phases (R=0.520, p=0.0271). In contrast, the correlation between estradiol level and laser-Doppler flux response was observed only in the follicular phase (R=-0.506, p=0.0324). Our results show that individual sensitivity to cold influences cutaneous microvascular response to local cooling; that microvascular reactivity is more pronounced during the luteal phase of the menstrual cycle; and that reactivity correlates with hormone levels. The effect of specific sex hormone levels is related to the cold-provocation temperature. Copyright © 2016. Published by Elsevier Inc.

Viscoelastic behaviour of cold recycled asphalt mixes

NASA Astrophysics Data System (ADS)

Cizkova, Zuzana; Suda, Jan

2017-09-01

Behaviour of cold recycled mixes depends strongly on both the bituminous binder content (bituminous emulsion or foamed bitumen) and the hydraulic binder content (usually cement). In the case of cold recycled mixes rich in bitumen and with low hydraulic binder content, behaviour is close to the viscoelastic behaviour of traditional hot mix asphalt. With decreasing bituminous binder content together with increasing hydraulic binder content, mixes are characteristic with brittle behaviour, typical for concrete pavements or hydraulically bound layers. The behaviour of cold recycled mixes with low content of both types of binders is similar to behaviour of unbound materials. This paper is dedicated to analysing of the viscoelastic behaviour of the cold recycled mixes. Therefore, the tested mixes contained higher amount of the bituminous binder (both foamed bitumen and bituminous emulsion). The best way to characterize any viscoelastic material in a wide range of temperatures and frequencies is through the master curves. This paper includes interesting findings concerning the dependency of both parts of the complex modulus (elastic and viscous) on the testing frequency (which simulates the speed of heavy traffic passing) and on the testing temperature (which simulates the changing climate conditions a real pavement is subjected to).

65th birthday Jack Steinberger

ScienceCinema

None

2017-12-09

Laudatio pour Jack Steinberger né le 25 mai 1921, à l'occasion de son 65me anniversaire et sa retraite officielle, pour sa précieuse collaboration au Cern. Néanmoins son principal activité continuera comme avant dans sa recherche au Cern. Plusieurs orateurs prennent la parole (p.ex. E.Picasso) pour le féliciter et lui rendre hommage

Matériaux pour la dépollution des gaz d'échappement automobile

NASA Astrophysics Data System (ADS)

Mouaddib-Moral, N.; Gauthier, C.

2002-04-01

Les premières législations antipollution ont été mises en place suite à la détection, aux Etats Unis plus particulièrement en Californie, du smog photochimique et des pluies acides, néfastes pour la faune et la flore. Les estimations de la contribution de l'automobile aux émissions de composés, considérés comme précurseurs de ces phénomènes, ont été suffisantes pour provoquer la mise en place de normes draconiennes en matière d'émissions automobiles. Les matériaux catalytiques ont été évalués en tant que solution possible pour réduire les émissions à l'échappement. En Europe, l'utilisation des catalyseurs trois voies a été généralisée sur les véhicules essence fonctionnant à richesse stoechiométrique à partir de 1993. Une nouvelle génération de catalyseurs appelée piège à oxydes d'azote (NOx) est maintenant nécessaire pour le post-traitement des gaz d'échappement des motorisations à essence fonctionnant en mélange pauvre (combustion en présence d'un excès d'oxygène) pour diminuer la consommation et par conséquent réduire les émissions du CO2 connu pour son impact sur l'effet de serre. La dépollution des moteurs diesel via un catalyseur d'oxydation a été généralisée en Europe depuis 1996. La sévérisation des normes européennes impose pour les moteurs diesel le recours à des matériaux spécifiques pour le traitement des oxydes d'azotes et des particules par l'intermédiaire de filtres à particules dont l'efficacité de filtration est supérieure à 95%, mais doivent subir des régénérations périodiques.

49 CFR 40.71 - How does the collector prepare the specimens?

Code of Federal Regulations, 2011 CFR

2011-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Specimen Collections § 40.71 How does the... brings the urine specimen to you. You must take these steps in the presence of the employee. (1) Check... employee, must first pour at least 30 mL of urine from the collection container into one specimen bottle...

49 CFR 40.71 - How does the collector prepare the specimens?

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Specimen Collections § 40.71 How does the... brings the urine specimen to you. You must take these steps in the presence of the employee. (1) Check... employee, must first pour at least 30 mL of urine from the collection container into one specimen bottle...

49 CFR 40.71 - How does the collector prepare the specimens?

Code of Federal Regulations, 2010 CFR

2010-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Specimen Collections § 40.71 How does the... brings the urine specimen to you. You must take these steps in the presence of the employee. (1) Check... employee, must first pour at least 30 mL of urine from the collection container into one specimen bottle...

49 CFR 40.71 - How does the collector prepare the specimens?

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Specimen Collections § 40.71 How does the... brings the urine specimen to you. You must take these steps in the presence of the employee. (1) Check... employee, must first pour at least 30 mL of urine from the collection container into one specimen bottle...

49 CFR 40.71 - How does the collector prepare the specimens?

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Specimen Collections § 40.71 How does the... brings the urine specimen to you. You must take these steps in the presence of the employee. (1) Check... employee, must first pour at least 30 mL of urine from the collection container into one specimen bottle...

16 CFR 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) below the target temperature, remove the cooling block and quickly dry the cup with a paper tissue to... (cooling) fluid is solid carbon dioxide (dry ice) and acetone. If the refrigerant charged cooling module is... pouring acetone. Use only in a well-ventilated area. Avoid inhalation and contact with the eyes or skin...

Commissioning and operational results of helium refrigeration system at JLab for the 12GeV upgrade

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knudsen, Peter N.; Ganni, Venkatarao; Dixon, Kelly D.

The new 4.5 K refrigerator system at the Jefferson Lab (JLab) Central Helium Liquefier (CHL-2) for the 12 GeV upgrade was commissioned in late spring of 2013, following the commissioning of the new compressor system, and has been supporting 12 GeV LINAC commissioning since that time. Six design modes were tested during commissioning, consisting of a maximum capacity, nominal capacity, maximum liquefaction, maximum refrigeration, maximum fill and a stand-by/reduced load condition. The maximum capacity was designed to support a 238 g/s, 30 K and 1.16 bar cold compressor return flow, a 15 g/s, 4.5 K liquefaction load and a 12.6more » kW, 35-55 K shield load. The other modes were selected to ensure proper component sizing and selection to allow the cold box to operate over a wide range of conditions and capacities. The cold box system is comprised of two physically independent cold boxes with interconnecting transfer-lines. The outside (upper) 300-60 K vertical cold box has no turbines and incorporates a liquid nitrogen pre-cooler and 80-K beds. The inside (lower) 60-4.5 K horizontal cold box houses seven turbines that are configured in four expansion stages including one Joule-Thompson expander and a 20-K bed. The helium compression system has five compressors to support three pressure levels in the cold box. This paper will summarize the analysis of the test data obtained over the wide range of operating conditions and capacities which were tested.« less

Revetements bioactifs a base de chondroitine sulfate et de facteurs de croissance pour applications vasculaires

NASA Astrophysics Data System (ADS)

Lequoy, Pauline

Malgre des avancees technologiques indeniables, l'efficacite des implants biomedicaux est encore limitee par les biomateriaux synthetiques qui les composent, notamment en raison de leur incapacite a generer une reponse biologique adequate. En particulier, la guerison tissulaire autour des implants vasculaires reste problematique. Une etude de la litterature a montre que dans le cas des endoprotheses couvertes (tuyaux polymeriques utilises pour la reparation endovasculaire des anevrismes de l'aorte abdominale), le manque de guerison observe s'explique non seulement par l'inertie des biomateriaux utilises mais aussi par le fait que l'implant est insere dans un vaisseau malade favorisant la mort des cellules par apoptose et presentant une depletion cellulaire marquee. L'hypothese a la base de ce projet est qu'un revetement bioactif pourrait ameliorer la guerison et la colonisation de l'implant par les cellules vasculaires et ainsi favoriser l'attachement de l'implant dans le vaisseau malade afin de prevenir les complications a long terme. Dans ce contexte, deux molecules anti-apoptotiques ont ete selectionnees pour developper le revetement, la chondroitine sulfate (CS), un glycosaminoglycane de la matrice extracellulaire, et le facteur de croissance de l'epiderme (EGF) qui possede egalement un role important dans la guerison tissulaire. L'un des defis de ce projet est de preserver la bioactivite de ces molecules lors de leur immobilisation dans un revetement. Pour etablir une preuve de concept, nous avons demontre qu'un revetement CS+EGF obtenu par greffage covalent permet d'ameliorer significativement la survie des cellules vasculaires humaines (cellules musculaires lisses, CMLV, et fibroblastes) sur les materiaux realistes (PET, ePTFE). Apres avoir transfere ce revetement sur des implants commerciaux en ePTFE, des tests in vivo ont demontre une amelioration de la guerison grâce au revetement bioactif, cependant la guerison n'a pas ete totale dans la cavite anevrismale. Pour ameliorer la bioactivite du revetement, un systeme de capture oriente base sur la complementarite de deux peptides (superhelices 'coiled-coil') a ete utilise pour immobiliser l'EGF sur CS. Cette immobilisation orientee a permis une meilleure efficacite de capture, ainsi qu'une augmentation marquee de la survie des CMLV par rapport au greffage covalent aleatoire utilise precedemment. De plus, les travaux realises ont permis l'avancement de la comprehension des proprietes antiadhesives selectives de CS par comparaison avec le dextrane carboxymethyle. Enfin, nous avons demontre que la polyvalence du systeme de capture oriente pour facteurs de croissance permet la co-immobilisation de deux facteurs de croissance, EGF et VEGF (facteur de croissance de l'endothelium vasculaire), et ce a des ratios variables. Les densites surfaciques ont ete optimisees par simple changement de concentration lors de l'incubation. Des etudes cellulaires avec une gamme de ratios EGF/VEGF ont revele un effet synergique des deux facteurs de croissance sur la survie des CMLV et des cellules endotheliales. Les travaux menes ont permis de developper des revetements bioactifs anti-apoptotiques qui ameliorent la survie des cellules vasculaires et constituent une avancee vers la creation d'endoprotheses bioactives. Il apparait egalement que la plateforme d'immobilisation coiled-coil presente un grand potentiel pour la construction de surfaces bioactives complexes et la comprehension du role de differents facteurs de croissance dans les comportements cellulaires.

Developpement d'une methode de Monte Carlo dependante du temps et application au reacteur de type CANDU-6

NASA Astrophysics Data System (ADS)

Mahjoub, Mehdi

La resolution de l'equation de Boltzmann demeure une etape importante dans la prediction du comportement d'un reacteur nucleaire. Malheureusement, la resolution de cette equation presente toujours un defi pour une geometrie complexe (reacteur) tout comme pour une geometrie simple (cellule). Ainsi, pour predire le comportement d'un reacteur nucleaire,un schema de calcul a deux etapes est necessaire. La premiere etape consiste a obtenir les parametres nucleaires d'une cellule du reacteur apres une etape d'homogeneisation et condensation. La deuxieme etape consiste en un calcul de diffusion pour tout le reacteur en utilisant les resultats de la premiere etape tout en simplifiant la geometrie du reacteur a un ensemble de cellules homogenes le tout entoure de reflecteur. Lors des transitoires (accident), ces deux etapes sont insuffisantes pour pouvoir predire le comportement du reacteur. Comme la resolution de l'equation de Boltzmann dans sa forme dependante du temps presente toujours un defi de taille pour tous types de geometries,un autre schema de calcul est necessaire. Afin de contourner cette difficulte, l'hypothese adiabatique est utilisee. Elle se concretise en un schema de calcul a quatre etapes. La premiere et deuxieme etapes demeurent les memes pour des conditions nominales du reacteur. La troisieme etape se resume a obtenir les nouvelles proprietes nucleaires de la cellule a la suite de la perturbation pour les utiliser, au niveau de la quatrieme etape, dans un nouveau calcul de reacteur et obtenir l'effet de la perturbation sur le reacteur. Ce projet vise a verifier cette hypothese. Ainsi, un nouveau schema de calcul a ete defini. La premiere etape de ce projet a ete de creer un nouveau logiciel capable de resoudre l'equation de Boltzmann dependante du temps par la methode stochastique Monte Carlo dans le but d'obtenir des sections efficaces qui evoluent dans le temps. Ce code a ete utilise pour simuler un accident LOCA dans un reacteur nucleaire de type CANDU-6. Les sections efficaces dependantes du temps ont ete par la suite utilisees dans un calcul de diffusion espace-temps pour un reacteur CANDU-6 subissant un accident de type LOCA affectant la moitie du coeur afin d'observer son comportement durant toutes les phases de la perturbation. Dans la phase de developpement, nous avons choisi de demarrer avec le code OpenMC, developpe au MIT,comme plateforme initiale de developpement. L'introduction et le traitement des neutrons retardes durant la simulation ont presente un grand defi a surmonter. Il est important de noter que le code developpe utilisant la methode Monte Carlo peut etre utilise a grande echelle pour la simulation de tous les types des reacteurs nucleaires si les supports informatiques sont disponibles.

Methods of Testing Thermal Insulation and Associated Test Apparatus

NASA Technical Reports Server (NTRS)

Fesmire, James E. (Inventor); Augustynowicz, Stanislaw D. (Inventor)

2004-01-01

The system and method for testing thermal insulation uses a cryostatic insulation tester having a vacuum chamber and a cold mass including a test chamber and upper and lower guard chambers adjacent thereto. The thermal insulation is positioned within the vacuum chamber and adjacent the cold mass. Cryogenic liquid is supplied to the test chamber, upper guard and lower guard to create a first gas layer in an upper portion of the lower guard chamber and a second gas layer in an upper portion of the test chamber. Temperature are sensed within the vacuum chamber to test the thermal insulation.

40 CFR 86.201-11 - General applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.201-11 General applicability. (a) This subpart describes procedures for determining the cold temperature carbon monoxide (CO) emissions from 1994...

40 CFR 86.201-94 - General applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.201-94 General applicability. (a) This subpart describes procedures for determining the cold temperature carbon monoxide (CO) emission from 1994...

40 CFR 86.201-94 - General applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.201-94 General applicability. (a) This subpart describes procedures for determining the cold temperature carbon monoxide (CO) emission from 1994...

40 CFR 86.201-94 - General applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.201-94 General applicability. (a) This subpart describes procedures for determining the cold temperature carbon monoxide (CO) emission from 1994...

40 CFR 86.201-11 - General applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.201-11 General applicability. (a) This subpart describes procedures for determining the cold temperature carbon monoxide (CO) emissions from 1994...

40 CFR 86.201-11 - General applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.201-11 General applicability. (a) This subpart describes procedures for determining the cold temperature carbon monoxide (CO) emissions from 1994...

Modélisation des conséquences possibles de la future demande bioénergétique mondiale pour le bois et les forêts en France

Treesearch

Joseph Buongiorno; Ronald Raunikar; Shusuai Zhu

2011-01-01

L’accroissement de la demande mondiale et du coût correspondant de l’énergie a conduit à de nombreuses propositions pour augmenter l’utilisation de la biomasse renouvelable. Une étude récente (Raunikar et al., 2010) a examiné les conséquences mondiales pour le bois et pour les forêts de la demande en bioénergie impliquée par les scénarios du Groupe d’experts...

Urinary excretion of adrenal steroids, catecholamines and electrolytes in man, before and after acclimatization to cold in Antarctica

PubMed Central

Budd, G. M.; Warhaft, N.

1970-01-01

1. Urine samples were collected from four men before and during test cold exposures in Melbourne, Australia, and Mawson, Antarctica. Changes in the response of body temperature to the test exposures showed that the men had acclimatized to cold at Mawson. 2. Excretion rates of 17-hydroxycorticosteroids and 17-ketosteroids were significantly greater at Mawson than in Melbourne, in both the pre-exposure and exposure periods. 3. Excretion rates of noradrenaline, adrenaline, sodium, potassium and creatinine did not differ significantly between Mawson and Melbourne, nor did urine flow rates. 4. During the cold exposure significant increases occurred, to the same extent at Mawson as in Melbourne, in urine flow rate and in all measured urinary constituents except creatinine. PMID:5501486

INDUCTION HEATING PROCESS FOR MELTING TITANIUM (COLD-WALL CRUCIBLES, SEGMENTED AND NON-SEGMENTED).

DTIC Science & Technology

system during melting tests. Three types of cold-wall crucibles were investigated. The first was a four-segment copper crucible , the second a non...segmented silicon bronze crucible, and the third a two-segment copper crucible coated with BeO. Attempts to melt titanium in an induction field in a cold

Identification of Sweet Sorghum accessions with seedling cold tolerance using both lab cold germination test and field early Spring planting evaluation

USDA-ARS?s Scientific Manuscript database

Cultivars with quick seedling emergence and stand establishment at early spring cold conditions may be planted early in the same region with an extended period of plant growth and can potentially increase either grain yield, stem sugar yield, or biomass production of sorghum. Planting cultivars with...

Unconscious affective reactions to masked happy versus angry faces influence consumption behavior and judgments of value.

PubMed

Winkielman, Piotr; Berridge, Kent C; Wilbarger, Julia L

2005-01-01

The authors explored three properties of basic, unconsciously triggered affective reactions: They can influence consequential behavior, they work without eliciting conscious feelings, and they interact with motivation. The authors investigated these properties by testing the influence of subliminally presented happy versus angry faces on pouring and consumption of beverage (Study 1), perception of beverage value (Study 2), and reports of conscious feelings (both studies). Consistent with incentive motivation theory, the impact of affective primes on beverage value and consumption was strongest for thirsty participants. Subliminal smiles caused thirsty participants to pour and consume more beverage (Study 1) and increased their willingness to pay and their wanting more beverage (Study 2). Subliminal frowns had the opposite effect. No feeling changes were observed, even in thirsty participants. The results suggest that basic affective reactions can be unconscious and interact with incentive motivation to influence assessment of value and behavior toward valenced objects.

Evaluation of the methods for enumerating coliform bacteria from water samples using precise reference standards.

PubMed

Wohlsen, T; Bates, J; Vesey, G; Robinson, W A; Katouli, M

2006-04-01

To use BioBall cultures as a precise reference standard to evaluate methods for enumeration of Escherichia coli and other coliform bacteria in water samples. Eight methods were evaluated including membrane filtration, standard plate count (pour and spread plate methods), defined substrate technology methods (Colilert and Colisure), the most probable number method and the Petrifilm disposable plate method. Escherichia coli and Enterobacter aerogenes BioBall cultures containing 30 organisms each were used. All tests were performed using 10 replicates. The mean recovery of both bacteria varied with the different methods employed. The best and most consistent results were obtained with Petrifilm and the pour plate method. Other methods either yielded a low recovery or showed significantly high variability between replicates. The BioBall is a very suitable quality control tool for evaluating the efficiency of methods for bacterial enumeration in water samples.

Analysis of cold worked holes for structural life extension

NASA Technical Reports Server (NTRS)

Wieland, David H.; Cutshall, Jon T.; Burnside, O. Hal; Cardinal, Joseph W.

1994-01-01

Cold working holes for improved fatigue life of fastener holes are widely used on aircraft. This paper presents methods used by the authors to determine the percent of cold working to be applied and to analyze fatigue crack growth of cold worked fastener holes. An elastic, perfectly-plastic analysis of a thick-walled tube is used to determine the stress field during the cold working process and the residual stress field after the process is completed. The results of the elastic/plastic analysis are used to determine the amount of cold working to apply to a hole. The residual stress field is then used to perform damage tolerance analysis of a crack growing out of a cold worked fastener hole. This analysis method is easily implemented in existing crack growth computer codes so that the cold worked holes can be used to extend the structural life of aircraft. Analytical results are compared to test data where appropriate.

Validation of standard ASTM F2732 and comparison with ISO 11079 with respect to comfort temperature ratings for cold protective clothing.

PubMed

Gao, Chuansi; Lin, Li-Yen; Halder, Amitava; Kuklane, Kalev; Holmér, Ingvar

2015-01-01

American standard ASTM F2732 estimates the lowest environmental temperature for thermal comfort for cold weather protective clothing. International standard ISO 11079 serves the same purpose but expresses cold stress in terms of required clothing insulation for a given cold climate. The objective of this study was to validate and compare the temperature ratings using human subject tests at two levels of metabolic rates (2 and 4 MET corresponding to 116.4 and 232.8 W/m(2)). Nine young and healthy male subjects participated in the cold exposure at 3.4 and -30.6 °C. The results showed that both standards predict similar temperature ratings for an intrinsic clothing insulation of 1.89 clo and for 2 MET activity. The predicted temperature rating for 2 MET activity is consistent with test subjects' thermophysiological responses, perceived thermal sensation and thermal comfort. For 4 MET activity, however, the whole body responses were on the cold side, particularly the responses of the extremities. ASTM F2732 is also limited due to its omission and simplification of three climatic variables (air velocity, radiant temperature and relative humidity) and exposure time in the cold which are of practical importance. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Room temperature creep behavior of Ti–Nb–Ta–Zr–O alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Wei-dong

The room temperature creep behavior and deformation mechanisms of a Ti–Nb–Ta–Zr–O alloy, which is also called “gum metal”, were investigated with the nanoindentation creep and conventional creep tests. The microstructure was observed with electron backscattered diffraction analysis (EBSD) and transmission electron microscopy (TEM). The results show that the creep stress exponent of the alloy is sensitive to cold deformation history of the alloy. The alloy which was cold swaged by 85% shows high creep resistance and the stress exponent is approximately equal to 1. Microstructural observation shows that creep process of the alloy without cold deformation is controlled by dislocationmore » mechanism. The stress-induced α' martensitic phase transformation also occurs. The EBSD results show that the grain orientation changes after the creep tests, and thus, the creep of the cold-worked alloy is dominated by the shear deformation of giant faults without direct assistance from dislocations. - Highlights: •Nanoindentation was used to investigate room temperature creep behavior of gum metal. •The creep stress exponent of gum metal is sensitive to the cold deformation history. •The creep stress exponent of cold worked gum metal is approximately equal to 1. •The creep of the cold-worked gum metal is governed by the shear deformation of giant faults.« less

Cold startup and low temperature performance of the Brayton cycle electrical subsystem

NASA Technical Reports Server (NTRS)

Vrancik, J. E.; Bainbridge, R. C.

1971-01-01

Cold performance tests and startup tests were conducted on the Brayton-cycle inverter, motor-driven pump, dc supply, speed control with parasitic load resistor and the Brayton control system. These tests were performed with the components in a vacuum and mounted on coldplates. A temperature range of ?25 to -50 C was used for the tests. No failures occurred, and component performance gave no indication that there would be any problem with the safe operation of the Brayton power generating system.

A cold ejector for closed-cycle helium refrigerators

NASA Technical Reports Server (NTRS)

Johnson, D. L.; Daggett, D. L.

1987-01-01

The test results are presented of an initial cold helium ejector design that can be installed on a closed cycle refrigerator to provide refrigeration at temperatures below 4.2 K. The ejector, test apparatus, instrumentation, and test results are described. Tests were conducted both at room temperature and at cryogenic temperatures to provide operational experience with the ejector as well as for future use in the subsequent design of an ejector that will provide refrigeration at temperatures below 3 K.

Grain boundary damage evolution and SCC initiation of cold-worked alloy 690 in simulated PWR primary water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhai, Ziqing; Toloczko, Mychailo B.; Kruska, Karen

Long-term grain boundary (GB) damage evolution and stress corrosion crack initiation in alloy 690 are being investigated by constant load tensile testing in high-temperature, simulated PWR primary water. Six commercial alloy 690 heats are being tested in various cold work conditions loaded at their yield stress. This paper reviews the basic test approach and detailed characterizations performed on selected specimens after an exposure time of ~1 year. Intergranular crack nucleation was observed under constant stress in certain highly cold-worked (CW) alloy 690 heats and was found to be associated with the formation of GB cavities. Somewhat surprisingly, the heats mostmore » susceptible to cavity formation and crack nucleation were thermally treated materials with most uniform coverage of small GB carbides. Microstructure, % cold work and applied stress comparisons are made among the alloy 690 heats to better understand the factors influencing GB cavity formation and crack initiation.« less

Essais de fissuration a froid appliques aux metaux d'apport inoxydables martensitiques 410NiMo

NASA Astrophysics Data System (ADS)

Paquin, Mathieu

Martensitic stainless steels have represented since few years a material of choice for the manufacture of mechanical parts such as hydroelectric turbines. The development of the alloy has led to grades with very low amount of carbon giving them a good weldability. The assembly of these parts, made by autogenous welding, requires the use of materials with low transformation temperature (LTT) such as 410NiMo. These filler metals are also used for assembly by heterogeneous welding of steel parts susceptible to cold cracking. The transformation of austenite to martensite occurring at low temperature, residual stresses from single-pass welding operation are different from those normally found and reduce the risk of cracking. By cons, industrial experience shows that in situation of multipass welding, the risks of cold cracking are still present. This project aimed to determine a cracking test for assessing susceptibility to cold cracking of 13%Cr-4%Ni stainless steel according to the welding procedure, in autogenous welding situation. Literature contains much information about cold cracking phenomena. That phenomena occurs under three conditions. These conditions are: a high diffusible hydrogen level, significant residual stresses and a brittle microstructure. It seems that despite the low mass ratio of carbon (0.022%C) and the low diffusible hydrogen level (< 3 ml/100g) risks of cold cracking remain present during multipass deposits. Use of cracking tests was necessary to assess the sensitivity to cracking of the martensitic stainless steel. Before the work preliminary tests have been made or tested Tekken GBOP and testing to determine that to obtain the most representative of the industrial reality results. Then they have been modified to reverse the compression stress in the seam test to tension by the addition of a second weld. This inversion occurs in multipass welding and has been targeted as an important factor in the occurrence of cold cracking phenomenon. The results of these tests show that Tekken test is not suitable for LTT testing. It was also demonstrated that GBOP test with two juxtaposed seams configuration gave results consistent with the industrial observations. The second stage of the project was to study the cracking test selected. Acoustic emission tests were done during welding and cooling of GBOP test. These tests were conducted in order to detect when the cracking of the test occurred and to validate the method of inspection. This inspection is done after separation of the specimen, by observation of the fracture surface. Usually, cliveage zone on the fracture surface can be associated with cold cracking and dimple zones can be associated with the specimen separation. Through these tests, it was possible to validate this assertion. Then the relevance of the addition of a second weld has been validated by studying the residual stress by the contour method. It was possible to observe an area of the first bead in tension, promoting cracking of the test. Finally, some test runs were made with various filler metals in order to confirm that the utilization of the modified GBOP test for 13%Cr-4%Ni was adequate. A fractographic study of some sample was also made.

Advanced development receiver thermal vacuum tests with cold wall

NASA Technical Reports Server (NTRS)

Sedgwick, Leigh M.

1991-01-01

The first ever testing of a full size solar dynamic heat receiver using high temperature thermal energy storage was completed. The heat receiver was designed to meet the requirements for operation on the Space Station Freedom. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber with liquid nitrogen cold shrouds and an aperture cold plate to partially simulate a low Earth orbit environment. The cavity of the receiver was heated by an infrared quartz lamp heater with 30 independently controllable zones to produce flux distributions typical of candidate concentrators. A closed Brayton cycle engine simulator conditioned a helium xenon gas mixture to specific interface conditions to simulate various operational modes of the solar dynamic power module. Inlet gas temperature, pressure, and flow rate were independently varied. A total of 58 simulated orbital cycles were completed during the test conduct period. The test hardware, execution of testing, test data, and post test inspections are described.

Facility Activation and Characterization for IPD Oxidizer Turbopump Cold-Flow Testing at NASA Stennis Space Center

NASA Technical Reports Server (NTRS)

Sass, J. P.; Raines, N. G.; Farner, B. R.; Ryan, H. M.

2004-01-01

The Integrated Powerhead Demonstrator (IPD) is a 250K lbf (1.1 MN) thrust cryogenic hydrogen/oxygen engine technology demonstrator that utilizes a full flow staged combustion engine cycle. The Integrated Powerhead Demonstrator (IPD) is part of NASA's Next Generation Launch Technology (NGLT) program, which seeks to provide safe, dependable, cost-cutting technologies for future space launch systems. The project also is part of the Department of Defense's Integrated High Payoff Rocket Propulsion Technology (IHPRPT) program, which seeks to increase the performance and capability of today s state-of-the-art rocket propulsion systems while decreasing costs associated with military and commercial access to space. The primary industry participants include Boeing-Rocketdyne and GenCorp Aerojet. The intended full flow engine cycle is a key component in achieving all of the aforementioned goals. The IPD Program achieved a major milestone with the successful completion of the IPD Oxidizer Turbopump (OTP) cold-flow test project at the NASA John C. Stennis Space Center (SSC) E-1 test facility in November 2001. A total of 11 IPD OTP cold-flow tests were completed. Following an overview of the NASA SSC E-1 test facility, this paper addresses the facility aspects pertaining to the activation and the cold-flow testing of the IPD OTP. In addition, some of the facility challenges encountered during the test project are addressed.

TEST REACTOR AREA PLOT PLAN CA. 1968. MTR AND ETR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

TEST REACTOR AREA PLOT PLAN CA. 1968. MTR AND ETR AREAS SOUTH OF PERCH AVENUE. "COLD" SERVICES NORTH OF PERCH. ADVANCED TEST REACTOR IN NEW SECTION WEST OF COLD SERVICES SECTION. NEW PERIMETER FENCE ENCLOSES BETA RAY SPECTROMETER, TRA-669, AN ATR SUPPORT FACILITY, AND ATR STACK. UTM LOCATORS HAVE BEEN DELETED. IDAHO NUCLEAR CORPORATION, FROM A BLAW-KNOX DRAWING, 3/1968. INL INDEX NO. 530-0100-00-400-011646, REV. 0. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Helium High Pressure Tanks at EADS Space Transportation New Technology with Thermoplastic Liner

DTIC Science & Technology

2005-07-13

l’art actuel pour l’application d’un liner thermoplastique sur le réservoir hélium 300 litres pour le lanceur ARIANE 5, réservoir actuellement réalisé à...L à liner thermoplastique ont complètement démontré le respect aux exigences majeures demandées pour le lanceur A5. Ces travaux finalisent la phase

40 CFR 464.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting... million pounds) of metal poured Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO...

40 CFR 464.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting... million pounds) of metal poured Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO...

AGARD/SMP Review Damage Tolerance for Engine Structures. 2. Defects and Quantitative Materials Behaviour

DTIC Science & Technology

1988-10-01

TURBISTAN). En ce qui concerne les materiaux pour aubes de turbine la question reste ouverte. La caracterisation des materiaux pour... caracterisation mecanique. Face aux couts des caracterisations et qualifications de materiaux pour disques de lurbomachines, il importe de tenter...de concentrer ses propres forces : une solution possible est de constituer des plans standard de caracterisation . Federer au sein d’un groupe de

Investigation of pouring temperature and holding time for semisolid metal feedstock production

NASA Astrophysics Data System (ADS)

Razak, N. A.; Ahmad, A. H.; Rashidi, M. M.

2017-10-01

Semisolid metal (SSM) processing, as a kind of new technology that exploits forming of alloys between solidus and liquidus temperatures, has attracted great attention from investigators for its thixotropic behaviour as well as having advantages in reducing porosity, macrosegregation, and forming forces during shaping process. Various techniques are employed to produce feedstock with fine globular microstructures, and direct thermal method is one of them. In this paper, the effect from different pouring temperatures and holding times using a direct thermal method on microstructure and hardness of aluminium alloy 6061 is presented. Molten aluminium alloy 6061 was poured into a cylindrical copper mould and cooled down to the semisolid temperature before being quenched in water at room temperature. The effect of different pouring temperatures of 660 °C, 680 °C, 700 °C, and holding time of 20 s, and 60 s on the microstructure of aluminium alloy 6061 were investigated. From the micrographs, it was found that the most globular structures were achieved at processing parameters of 660 °C pouring temperature and 60 s holding time. The highest density and hardness of the samples were found at the same processing parameters. It can be concluded that the most spheroidal microstructure, the highest density, and the hardness were recorded at lower pouring temperature and longer holding time.

Elastomeric impression materials: a comparison of accuracy of multiple pours.

PubMed

Kumar, Dheeraj; Madihalli, Anand U; Reddy, K Rajeev Kumar; Rastogi, Namrataa; Pradeep, N T

2011-07-01

The aim of the present study is to compare the various elastomeric impression materials in terms of accuracy and dimensional stability, with respect to obtaining multiple casts from a single elastomeric impression at various times of pours. Three master dies were prepared for the impression making, two of these were made of brass containing a central hole with undercuts. The third die simulated a conventionally prepared typodont maxillary central incisor. Three elastomeric impression materials were chosen for the study. Each impression was poured at various time periods. Casts thus obtained were evaluated under a traveling microscope to evaluate various dimensional changes. Addition silicones provided dies which were shorter in height and bigger in diameter. Polyethers provided dies which were shorter in both height and diameter. Condensation silicones showed insignificant changes from the master die at the immediate pour but deteriorated rapidly after that in subsequent pours. None of the impression material showed a consistent behavior up to the fourth pour. They occasionally showed deviation from the pattern, but all these values were statistically insignificant. Polyethers showed lesser ability than both the addition silicones as well as the condensation silicones to recover from induced deformation. Addition silicones as well as the condensation silicones have better ability to recover from induced deformation when compared to polyether.

Thermal perception thresholds among workers in a cold climate.

PubMed

Burström, Lage; Björ, Bodil; Nilsson, Tohr; Pettersson, Hans; Rödin, Ingemar; Wahlström, Jens

2017-10-01

To investigate whether exposure to cold could influence the thermal perception thresholds in a working population. This cross-sectional study was comprised of 251 males and females and was carried out at two mines in the northern part of Norway and Sweden. The testing included a baseline questionnaire, a clinical examination and measurements of thermal perception thresholds, on both hands, the index (Digit 2) and little (Digit 5) fingers, for heat and cold. The thermal perception thresholds were affected by age, gender and test site. The thresholds were impaired by experiences of frostbite in the fingers and the use of medication that potentially could affect neurosensory functions. No differences were found between the calculated normative values for these workers and those in other comparative investigations conducted in warmer climates. The study provided no support for the hypothesis that living and working in cold climate will lead to impaired thermal perception thresholds. Exposure to cold that had caused localized damage in the form of frostbite was shown to lead to impaired thermal perception.

In Vivo Assessment of Cold Tolerance through Chlorophyll-a Fluorescence in Transgenic Zoysiagrass Expressing Mutant Phytochrome A

PubMed Central

Gururani, Mayank Anand; Venkatesh, Jelli; Ganesan, Markkandan; Strasser, Reto Jörg; Han, Yunjeong; Kim, Jeong-Il; Lee, Hyo-Yeon; Song, Pill-Soon

2015-01-01

Chlorophyll-a fluorescence analysis provides relevant information about the physiology of plants growing under abiotic stress. In this study, we evaluated the influence of cold stress on the photosynthetic machinery of transgenic turfgrass, Zoysia japonica, expressing oat phytochrome A (PhyA) or a hyperactive mutant phytochrome A (S599A) with post-translational phosphorylation blocked. Biochemical analysis of zoysiagrass subjected to cold stress revealed reduced levels of hydrogen peroxide, increased proline accumulation, and enhanced specific activities of antioxidant enzymes compared to those of control plants. Detailed analyses of the chlorophyll-a fluorescence data through the so-called OJIP test exhibited a marked difference in the physiological status among transgenic and control plants. Overall, these findings suggest an enhanced level of cold tolerance in S599A zoysiagrass cultivars as reflected in the biochemical and physiological analyses. Further, we propose that chlorophyll-a fluorescence analysis using OJIP test is an efficient tool in determining the physiological status of plants under cold stress conditions. PMID:26010864

High brilliant thermal and cold moderator for the HBS neutron source project Jülich

NASA Astrophysics Data System (ADS)

Cronert, T.; Dabruck, J. P.; Doege, P. E.; Bessler, Y.; Klaus, M.; Hofmann, M.; Zakalek, P.; Rücker, U.; Lange, C.; Butzek, M.; Hansen, W.; Nabbi, R.; Brückel, T.

2016-09-01

The proposed High Brilliance Neutron Source (HBS), recognized within the Helmholtz Association of German Research Centres, will optimize the entire chain from particle source through particle accelerator, target, moderator, reflector, shielding, beam extraction, beam transport all the way to the detector, utilizing the nuclear Be(p,n) or Be(d,n) reaction in the lower MeV energy range. A D2O moderating reflector prototype (MRP) and a cold source were constructed and build according to MCNP parameter studies. The MRP was tested in a feasibility study at the TREFF instrument at MLZ (Garching). Cold beam extraction from the flux maximum within the moderator based on liquid para H2 and other cold moderators will be tested by energy spectroscopy via TOF-method. Different ratios of liquid ortho/para H2 will be fed to the cold moderator. The ratio will be controlled by feeding from reservoires of natural liquid H2 and a storage loop with an ortho/para converter and determined via online heat capacity measurement.

Thermal acclimation to cold alters myosin content and contractile properties of rainbow smelt, Osmerus mordax, red muscle.

PubMed

Coughlin, David J; Shiels, Lisa P; Nuthakki, Seshuvardhan; Shuman, Jacie L

2016-06-01

Rainbow smelt (Osmerus mordax), a eurythermal fish, live in environments from -1.8 to 20°C, with some populations facing substantial annual variation in environmental temperature. These different temperature regimes pose distinct challenges to locomotion by smelt. Steady swimming performance, red muscle function and muscle myosin content were examined to assess the prediction that cold acclimation by smelt will lead to improved steady swimming performance and that any performance shift will be associated with changes in red muscle function and in its myosin heavy chain composition. Cold acclimated (4°C) smelt had a faster maximum steady swimming speed and swam with a higher tailbeat frequency than warm acclimated (10°C) smelt when tested at the same temperature (10°C). Muscle mechanics experiments demonstrated faster contractile properties in the cold acclimated fish when tested at 10°C. The red muscle of cold acclimated smelt had a shorter twitch times, a shorter relaxation times and a higher maximum shortening velocity. In addition, red muscle from cold acclimated fish displayed reduced thermal sensitivity to cold, maintaining higher force levels at 4°C compared to red muscle from warm acclimated fish. Immunohistochemistry suggests shifts in muscle myosin composition and a decrease in muscle cross-sectional area with cold acclimation. Dot blot analysis confirmed a shift in myosin content. Rainbow smelt do show a significant thermal acclimation response to cold. An examination of published values of maximum muscle shortening velocity in fishes suggests that smelt are particularly well suited to high levels of activity in very cold water. Copyright © 2016 Elsevier Inc. All rights reserved.

Large drinks are no mistake: Glass size, but not shape, affects alcoholic beverage drink pours

PubMed Central

Kerr, William C.; Patterson, Deidre; Koenen, Mary Albert; Greenfield, Thomas K.

2009-01-01

Introduction and Aims Drink alcohol content has been shown to be variable and is an important determinant of alcohol intake. This study evaluates claims regarding the effects of glass size and glass shape on the amount of alcohol in on-premise drinks. Design and Methods Wine and spirits drinks were purchased and measured in 80 on-premise establishments in 10 Northern California Counties. Drink alcohol content was measured as the liquid volume of the drink multiplied by the percentage alcohol by volume of given brands or from analysis of mixed drink and wine samples. Results Larger glass size was associated with larger on-premise pours of straight shots and mixed drinks served in the relatively large pint glass and variable “other” glass type were found to contain more alcohol than drinks served in a short wide glass. No significant differences were found for other drink types. Drinks poured in short wide glasses were not found to contain more alcohol than drinks poured in tall thin glasses. Bars with mostly black patrons were found to serve spirits drinks with more alcohol than bars with other patron types. Discussion and Conclusions Glass shape does not affect actual drink pours in the US but glass size does in some cases. Drinkers should measure wine and spirits pours at home to achieve standard drink amounts and consumer education programs should foster awareness of the relatively high drink alcohol content of on-premise wine and mixed spirits drinks. More research is needed to evaluate potential differences in drink pours by patron race and ethnicity. PMID:19594789

A Study on Passive and Electrochemical Response of Pure Nickel in Borate Buffer Solutions: Effect of Cold Deformation

NASA Astrophysics Data System (ADS)

Fattah-alhosseini, Arash; Naseri, Majid; Gashti, Seyed Omid; Vafaeian, Saeed; Keshavarz, Mohsen K.

2018-06-01

In the present work, influences of the cold deformation on electrochemical and passive response of pure nickel in three solutions with adjusted pH values of 8.5, 9.0, and 9.5 at 298 ± 1 K (25 ± 1 °C) were investigated. A cold deformation process was applied by means of cold rolling. Implementation of the cold deformation process resulted in samples having a finer microstructure. Also, the cold work and grain refinement led to increased hardness. In addition, open-circuit potential and potentiodynamic polarization tests were performed and results showed that corrosion current density was reduced by applying the cold deformation. Moreover, the results of the electrochemical impedance spectroscopy and Mott-Schottky analyses indicated higher corrosion resistance of pure nickel after cold deformation. This behavior is attributed to the growth of much thicker, with less point defects, passive layer on the surface of cold-deformed samples.

Revetements antireflet-passivation a base de nitrure de silicium PECVD pour cellules solaires triple-jonction III-V/ Ge

NASA Astrophysics Data System (ADS)

Homier, Ram

Dans le contexte environnemental actuel, le photovoltaïque bénéficie de l'augmentation des efforts de recherche dans le domaine des énergies renouvelables. Pour réduire le coût de la production d'électricité par conversion directe de l'énergie lumineuse en électricité, le photovoltaïque concentré est intéressant. Le principe est de concentrer une grande quantité d'énergie lumineuse sur des petites surfaces de cellules solaires multi-jonction à haute efficacité. Lors de la fabrication d'une cellule solaire, il est essentiel d'inclure une méthode pour réduire la réflexion de la lumière à la surface du dispositif. Le design d'un revêtement antireflet (ARC) pour cellules solaires multi-jonction présente des défis à cause de la large bande d'absorption et du besoin d'égaliser le courant produit par chaque sous-cellule. Le nitrure de silicium déposé par PECVD en utilisant des conditions standards est largement utilisé dans l'industrie des cellules solaires à base de silicium. Cependant, ce diélectrique présente de l'absorption dans la plage des courtes longueurs d'onde. Nous proposons l'utilisation du nitrure de silicium déposé par PECVD basse fréquence (LFSiN) optimisé pour avoir un haut indice de réfraction et une faible absorption optique pour l'ARC pour cellules solaires triple-jonction III-V/Ge. Ce matériau peut aussi servir de couche de passivation/encapsulation. Les simulations montrent que l'ARC double couche SiO2/LFSiN peut être très efficace pour réduire les pertes par réflexion dans la plage de longueurs d'onde de la sous-cellule limitante autant pour des cellules solaires triple-jonction limitées par la sous-cellule du haut que pour celles limitées par la sous-cellule du milieu. Nous démontrons aussi que la performance de la structure est robuste par rapport aux fluctuations des paramètres des couches PECVD (épaisseurs, indice de réfraction). Mots-clés : Photovoltaïque concentré (CPV), cellules solaires multi-jonction (MJSC), revêtement antireflet (ARC), passivation des semiconducteurs III-V, nitrure de silicium (Si"Ny), PECVD.

Large Blast and Thermal Simulator Reflected Wave Eliminator Study

DTIC Science & Technology

1990-03-01

it delays the passage of this wave through the test section until after the test is complete. The required length of extra duct depends on the strength...tube axis, which acts like an additional contraction effect since Se = Sj/[Cqsin(aj)]. Tii extra area is illustrated best by plotting (Se-Ae)/Ac versus...34Simulation de Choc et de Soaffie. Comimpensateur d’Ondes de Detente de Bouche pour tube a Choc de 2400 mm de diametre de Veine. Description, Compte- Renda

Air Intakes for High Speed Vehicles (Prises d’Air pour Vehicules a Grande Vitesse)

DTIC Science & Technology

1991-09-01

contributors. The a number of test cases for which rather Working Group wishes to express its detailed experimental data were available sincere thanks to those...larger group . Figs. 3.6.2 and 3.6.3 shows a 3.3.6.3 CFD TECHNIQUES comparison of the computed and experimental static pressure This test case was attempted...by six distributions on the ramp and cowl of different research groups , using seven the intake. Experimental data is shown different codes, as noted

Inhibition of common cold-induced aggravation of childhood asthma by leukotriene receptor antagonists.

PubMed

Yoshihara, Shigemi; Fukuda, Hironobu; Abe, Toshio; Nishida, Mitsuhiro; Yamada, Yumi; Kanno, Noriko; Arisaka, Osamu

2012-09-01

Virus infection is an important risk factor for aggravation of childhood asthma. The objective of this study was to examine the effect of drugs on aggravation of asthma induced by a common cold. Asthma control was examined in a survey of 1,014 Japanese pediatric patients with bronchial asthma. The occurrence of common cold, asthma control, and drugs used for asthma control were investigated using a modified Childhood Asthma Control Test (C-ACT) for patients aged <4 years old and 4 to 11 years old, and an Asthma Control Test (ACT) for patients aged 12 to 15 years old. The status of asthma control did not differ among the age groups. The prevalence of common cold and aggravation of asthma were significantly higher in patients aged <4 years old. Control of asthma following common cold-induced aggravation was significantly less effective in patients aged <4 years old compared to those aged ≥4 years old. In patients aged <4 years old with a common cold, asthma control was significantly more effective for those treated with leukotriene receptor antagonists (LTRAs) compared to treatment without LTRAs. Asthma control did not differ between patients who did or did not take inhaled corticosteroids or long-acting β2 stimulants. These findings showed a high prevalence of common cold in younger patients with childhood asthma and indicated that common cold can induce aggravation of asthma. LTRAs are useful for long-term asthma control in very young patients who develop an asthma attack due to a common cold.

Cold-water acclimation does not modify whole-body fluid regulation during subsequent cold-water immersion.

PubMed

Stocks, J M; Patterson, M J; Hyde, D E; Jenkins, A B; Mittleman, K D; Taylor, N A S

2004-06-01

We investigated the impact of cold-water acclimation on whole-body fluid regulation using tracer-dilution methods to differentiate between the intracellular and extracellular fluid compartments. Seven euhydrated males [age 24.7 (8.7) years, mass 74.4 (6.4) kg, height 176.8 (7.8) cm, sum of eight skinfolds 107.4 (20.4) mm; mean (SD)] participated in a 14-day cold-water acclimation protocol, with 60-min resting cold-water stress tests [CWST; 18.1 (0.1) degrees C] on days 1, 8 and 15, and 90-min resting cold-water immersions [18.4 (0.4) degrees C] on intervening days. Subjects were immersed to the 4th intercostal space. Intracellular and extracellular fluid compartments, and plasma protein, electrolyte and hormone concentrations were investigated. During the first CWST, the intracellular fluid (5.5%) and plasma volumes were reduced (6.1%), while the interstitial fluid volume was simultaneously expanded (5.4%). This pattern was replicated on days 8 and 15, but did not differ significantly among test days. Acclimation did not produce significant changes in the pre-immersion distribution of total body water, or changes in plasma osmolality, total protein, electrolyte, atrial natriuretic peptide or aldosterone concentrations. Furthermore, a 14-day cold-water acclimation regimen did not elicit significant changes in body-fluid distribution, urine production, or the concentrations of plasma protein, electrolytes or the fluid-regulatory hormones. While acclimation trends were not evident, we have confirmed that fluid from extravascular cells is displaced into the interstitium during acute cold-water immersion, both before and after cold acclimation.

C-reactive protein and cold-pressor tolerance in the general population: the Tromsø Study.

PubMed

Schistad, Elina Iordanova; Stubhaug, Audun; Furberg, Anne-Sofie; Engdahl, Bo Lars; Nielsen, Christopher Sivert

2017-07-01

The aim of this study was to examine whether increases in severity of subclinical inflammation, measured by high-sensitivity C-reactive protein (hs-CRP), increased experimental pain sensitivity, measured by cold-pressor tolerance, and to test whether this relationship is independent of chronic pain. A large population-based study from 2007 to 2008, the sixth Tromsø Study, provided data from 12,981 participants. For the present analysis, complete data for 10,274 participants (age: median 58 years) were available. The main outcome measure was cold-pressor tolerance, tested by placing the dominant hand in circulating cold water (3°C) for a maximum of 106 seconds. Cox proportional hazard models, treating hand withdrawal during the cold-pressor test as the event and enduring the full test time as censored data, were used to investigate the relationship between hs-CRP levels (≤3 or >3 mg/L) and cold-pressure tolerance. The fully adjusted model was controlled for age, sex, education, body mass index, smoking status, alcohol consumption, emotional distress, statin usage, and self-reported presence of chronic pain. Additional analysis was performed in participants without chronic pain. Higher levels of hs-CRP were negatively related to cold-pressor tolerance (hazard ratio [HR] = 1.24, 95% confidence interval [CI], 1.12-1.37, P < 0.001), adjusted for age and sex. This relationship remained essentially unaltered after controlling for potential confounders (HR = 1.22, 95% CI, 1.09-1.36, P < 0.001), as well as for the presence of chronic pain (HR = 1.22, 95% CI, 1.09-1.36, P < 0.001). The present data show that subclinical inflammation is related to increased pain sensitivity, suggesting a potential role of inflammation in experimental pain which may be of importance for the development of clinical pain.

Thermal insulation testing method and apparatus

NASA Technical Reports Server (NTRS)

Fesmire, James E. (Inventor); Augustynowicz, Stanislaw D. (Inventor)

2004-01-01

A test apparatus and method of its use for evaluating various performance aspects of a test specimen is disclosed. A chamber within a housing contains a cold mass tank with a contact surface in contact with a first surface of a test specimen. The first surface of the test specimen is spaced from the second surface of the test specimen by a thickness. The second surface of the test specimen is maintained at a desired warm temperature. The first surface is maintained at a constant temperature by a liquid disposed within the cold mass tank. A boil-off flow rate of the gas is monitored and provided to a processor along with the temperature of the first and second surfaces of the test specimen. The processor calculates thermal insulation values of the test specimen including comparative values for heat flux and apparent thermal conductivity (k-value). The test specimen may be placed in any vacuum pressure level ranging from about 0.01 millitorr to 1,000,000 millitorr with different residual gases as desired. The test specimen may be placed under a mechanical load with the cold mass tank and another factors may be imposed upon the test specimen so as to simulate the actual use conditions.

Thermal Insulation Testing Method and Apparatus

NASA Technical Reports Server (NTRS)

Fesmire, James E. (Inventor); Augustynowicz, Stanislaw D. (Inventor)

2004-01-01

A test apparatus and method of its use for evaluating various performance aspects of a test specimen is disclosed. A chamber within a housing contains a cold mass tank with a contact surface in contact with a first surface of a test specimen. The first surface of the test specimen is spaced from the second surface of the test specimen by a thickness. The second surface of the test specimen is maintained at a a constant temperature by a liquid disposed within the cold mass tank. A boil-off flow rate of the gas is monitored and provided to a processor along with the temperature of the first and second surfaces of the test specimen. The processor calculates thermal insulation values of the test specimen including comparative values for heat flux and apparent thermal conductivity k-value). The test specimen may be placed in any vacuum pressure level ranging from about 0.01 millitorr to 1,000,000 millitorr with different residual gases as desired. The test specimen may be placed under a mechanical load with the cold mass tank and another factors may be imposed upon the test specimen so as to simulate the actual use conditions.

Finite element simulations and experimental investigations on ductile fracture in cold forging of aluminum alloy

NASA Astrophysics Data System (ADS)

Amiri, Amir; Nikpour, Amin; Saraeian, Payam

2018-05-01

Forging is one of the manufacturing processes of aluminium parts which has two major categories: called hot and cold forging. In the cold forging, the dimensional and geometrical accuracy of final part is high. However, fracture may occur in some aluminium alloys during the process because of less workability. Fracture in cold forging can be in the form of ductile, brittle or combination of both depending on the alloy type. There are several criteria for predicting fracture in cold forging. In this study, cold forging process of 6063 aluminium alloy for three different parts is simulated in order to predict fracture. The results of numerical simulations of Freudenthal criterion is in conformity with experimental tests.

Experimental study on the monomer structure of solar semiconductor cold wall

NASA Astrophysics Data System (ADS)

Fu, Yuanyuan; Liu, Qiuxin; Chen, Tianshou

2018-06-01

In this paper, solar semiconductor cold wall structure was adopted in the net-zero energy buildings, NZEB for short. The heat transfer and refrigeration effect of the monomer structure of semiconductor cold wall were tested, we get that the monomer structure of semiconductor cold wall has certain cooling effect. However, the heat exchange effect is not good of the cold and hot aluminum plate only through natural convection and radiation heat transfer. It is necessary to further study the process of semiconductor refrigeration and heat transfer and the factors that affect the cooling effect. At the same time, it put forward a series of suggestions and improvement opinion for NZEB in hot summer and cold winter areas.

Inducing Cold-Sensitivity in the Frigophilic Fly Drosophila montana by RNAi

PubMed Central

Cook, Nicola; Tournière, Océane; Sneddon, Tanya; Ritchie, Michael G.

2016-01-01

Cold acclimation is a critical physiological adaptation for coping with seasonal cold. By increasing their cold tolerance individuals can remain active for longer at the onset of winter and can recover more quickly from a cold shock. In insects, despite many physiological studies, little is known about the genetic basis of cold acclimation. Recently, transcriptomic analyses in Drosophila virilis and D. montana revealed candidate genes for cold acclimation by identifying genes upregulated during exposure to cold. Here, we test the role of myo-inositol-1-phosphate synthase (Inos), in cold tolerance in D. montana using an RNAi approach. D. montana has a circumpolar distribution and overwinters as an adult in northern latitudes with extreme cold. We assessed cold tolerance of dsRNA knock-down flies using two metrics: chill-coma recovery time (CCRT) and mortality rate after cold acclimation. Injection of dsRNAInos did not alter CCRT, either overall or in interaction with the cold treatment, however it did induced cold-specific mortality, with high levels of mortality observed in injected flies acclimated at 5°C but not at 19°C. Overall, injection with dsRNAInos induced a temperature-sensitive mortality rate of over 60% in this normally cold-tolerant species. qPCR analysis confirmed that dsRNA injection successfully reduced gene expression of Inos. Thus, our results demonstrate the involvement of Inos in increasing cold tolerance in D. montana. The potential mechanisms involved by which Inos increases cold tolerance are also discussed. PMID:27832122

[Research advances in mathematical model of coniferous trees cold hardiness].

PubMed

Zhang, Gang; Wang, Ai-Fang

2007-07-01

Plant cold hardiness has complicated attributes. This paper introduced the research advances in establishing the dynamic models of coniferous trees cold hardiness, with the advantages and disadvantages of the models presented and the further studies suggested. In the models established initially, temperature was concerned as the only environmental factor affecting the cold hardiness, and the concept of stationary level of cold hardiness was introduced. Due to the obvious prediction errors of these models, the stationary level of cold hardiness was modeled later by assuming the existence of an additive effect of temperature and photoperiod on the increase of cold hardiness. Furthermore, the responses of the annual development phases for cold hardiness to environment were considered. The model researchers have paid more attention to the additive effect models, and run some experiments to test the additivity principle. However, the research results on Scots pine (Pinus sylvestris) indicated that its organs did not support the presumption of an additive response of cold hardiness by temperature and photoperiod, and the interaction between environmental factors should be taken into account. The mathematical models of cold hardiness need to be developed and improved.

Development of a model and test equipment for cold flow tests at 500 atm of small nuclear light bulb configurations

NASA Technical Reports Server (NTRS)

Jaminet, J. F.

1972-01-01

A model and test equipment were developed and cold-flow-tested at greater than 500 atm in preparation for future high-pressure rf plasma experiments and in-reactor tests with small nuclear light bulb configurations. With minor exceptions, the model chamber is similar in design and dimensions to a proposed in-reactor geometry for tests with fissioning uranium plasmas in the nuclear furnace. The model and the equipment were designed for use with the UARL 1.2-MW rf induction heater in tests with rf plasmas at pressures up to 500 atm. A series of cold-flow tests of the model was then conducted at pressures up to about 510 atm. At 504 atm, the flow rates of argon and cooling water were 3.35 liter/sec (STP) and 26 gal/min, respectively. It was demonstrated that the model is capable of being operated for extended periods at the 500-atm pressure level and is, therefore, ready for use in initial high-pressure rf plasma experiments.

Vernalizing cold is registered digitally at FLC.

PubMed

Angel, Andrew; Song, Jie; Yang, Hongchun; Questa, Julia I; Dean, Caroline; Howard, Martin

2015-03-31

A fundamental property of many organisms is an ability to sense, evaluate, and respond to environmental signals. In some situations, generation of an appropriate response requires long-term information storage. A classic example is vernalization, where plants quantitatively sense long-term cold and epigenetically store this cold-exposure information to regulate flowering time. In Arabidopsis thaliana, stable epigenetic memory of cold is digital: following long-term cold exposure, cells respond autonomously in an all-or-nothing fashion, with the fraction of cells that stably silence the floral repressor flowering locus C (FLC) increasing with the cold exposure duration. However, during cold exposure itself it is unknown whether vernalizing cold is registered at FLC in individual cells in an all-or-nothing (digital) manner or is continuously varying (analog). Using mathematical modeling, we found that analog registration of cold temperature is problematic due to impaired analog-to-digital conversion into stable memory. This disadvantage is particularly acute when responding to short cold periods, but is absent when cold temperatures are registered digitally at FLC. We tested this prediction experimentally, exposing plants to short periods of cold interrupted with even shorter warm breaks. For FLC expression, we found that the system responds similarly to both interrupted and uninterrupted cold, arguing for a digital mechanism integrating long-term temperature exposure.

Vernalizing cold is registered digitally at FLC

PubMed Central

Angel, Andrew; Song, Jie; Yang, Hongchun; Questa, Julia I.; Dean, Caroline; Howard, Martin

2015-01-01

A fundamental property of many organisms is an ability to sense, evaluate, and respond to environmental signals. In some situations, generation of an appropriate response requires long-term information storage. A classic example is vernalization, where plants quantitatively sense long-term cold and epigenetically store this cold-exposure information to regulate flowering time. In Arabidopsis thaliana, stable epigenetic memory of cold is digital: following long-term cold exposure, cells respond autonomously in an all-or-nothing fashion, with the fraction of cells that stably silence the floral repressor FLOWERING LOCUS C (FLC) increasing with the cold exposure duration. However, during cold exposure itself it is unknown whether vernalizing cold is registered at FLC in individual cells in an all-or-nothing (digital) manner or is continuously varying (analog). Using mathematical modeling, we found that analog registration of cold temperature is problematic due to impaired analog-to-digital conversion into stable memory. This disadvantage is particularly acute when responding to short cold periods, but is absent when cold temperatures are registered digitally at FLC. We tested this prediction experimentally, exposing plants to short periods of cold interrupted with even shorter warm breaks. For FLC expression, we found that the system responds similarly to both interrupted and uninterrupted cold, arguing for a digital mechanism integrating long-term temperature exposure. PMID:25775579

Increased infestation of Asian citrus psyllids on cold treated sour orange seedlings: Its possible relation to biochemical changes in leaves

USDA-ARS?s Scientific Manuscript database

Cold-stressed sour orange seedling (Citrus aurantium L.) attracted significantly more Asian citrus psyllid (ACP) (Diaphorina citri Kuwayama) during 5h and 24h recovery periods compared to control plants in choice test experiment. Cold stressed plants were held/ placed at 6 ± 1°C for 6 days and then ...

2014 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, Mike

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (LA 000161 01, Modification B), for the wastewater land application site at the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond from November 1, 2013–October 31, 2014. The report contains the following information; Facility and system description; Permit required effluent monitoring data and loading rates; Permit required groundwater monitoring data; Status of compliance activities; Noncompliance issues; and Discussion of the facility’s environmental impacts. During the 2014 permit year, approximately 238 million gallons of wastewater were discharged to the Cold Waste Pond. Thismore » is well below the maximum annual permit limit of 375 million gallons. As shown by the groundwater sampling data, sulfate and total dissolved solids concentrations are highest near the Cold Waste Pond and decrease rapidly as the distance from the Cold Waste Pond increases. Although concentrations of sulfate and total dissolved solids are elevated near the Cold Waste Pond, both parameters are below the Ground Water Quality Rule Secondary Constituent Standards in the downgradient monitoring wells.« less

2012 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Advanced Test Reactor Complex Cold Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mike Lewis

2013-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (#LA 000161 01, Modification B), for the wastewater land application site at the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond from November 1, 2011 through October 31, 2012. The report contains the following information: Facility and system description Permit required effluent monitoring data and loading rates Groundwater monitoring data Status of compliance activities Noncompliance issues Discussion of the facility’s environmental impacts During the 2012 permit year, approximately 183 million gallons of wastewater were discharged to the Cold Waste Pond. This ismore » well below the maximum annual permit limit of 375 million gallons. As shown by the groundwater sampling data, sulfate and total dissolved solids concentrations are highest near the Cold Waste Pond and decrease rapidly as the distance from the Cold Waste Pond increases. Although concentrations of sulfate and total dissolved solids are elevated near the Cold Waste Pond, both parameters were below the Ground Water Quality Rule Secondary Constituent Standards in the down gradient monitoring wells.« less

Ablation laser pour la microélectronique plastique

NASA Astrophysics Data System (ADS)

Alloncle, A.-P.; Thomas, B.; Grojo, D.; Delaporte, Ph.; Sentis, M.; Sanaur, S.; Barret, M.; Collot, Ph.

2006-12-01

La microélectronique plastique connaît un développement sans précédent dans le domaine de la recherche. Cette étude s'intéresse à l'utilisation des lasers impulsionnels pour la réalisation de composants organiques sur supports souples. Les deux aspects plus particulièrement étudiés sont d'une part la gravure de polymère pour réaliser un canal entre la source et le drain, et d'autre part le développement d'un procédéde dépôt appelé LIFT pour Laser Induced Forward Transfer. Ce dernier pourrait notamment permettre dedéposer des composés organiques non solubles.

Spectroscopie pompe-sonde pour la détection de bioaérosols

NASA Astrophysics Data System (ADS)

Guyon, L.; Courvoisier, F.; Wood, V.; Boutou, V.; Bartelt, A.; Roth, M.; Rabitz, H.; Wolf, J. P.

2006-10-01

La fluorescence du Tryptophane excité par une impulsion ultra-brève à 270 nm peut être diminuée d'un facteur deux par une seconde impulsion à 800 nm, à l'aide d'un dispositif pompe-sonde. Cette décroissance est aussi observée pour les bactéries vivantes, dont le Tryptophane est l'un des fluorophores, tandis qu'aucune décroissance n'est observée pour d'autres molécules organiques comme le naphtalène ou le gazole, malgré des spectres d'absorption et de fluorescence similaires. Cette différence remarquable est très prometteuse pour la distinction d'aérosols biologiques et organiques.

Radial Pressure Pulse and Heart Rate Variability in Heat- and Cold-Stressed Humans

PubMed Central

Huang, Chin-Ming; Chang, Hsien-Cheh; Kao, Shung-Te; Li, Tsai-Chung; Wei, Ching-Chuan; Chen, Chiachung; Liao, Yin-Tzu; Chen, Fun-Jou

2011-01-01

This study aims to explore the effects of heat and cold stress on the radial pressure pulse (RPP) and heart rate variability (HRV). The subjects immersed their left hand into 45°C and 7°C water for 2 minutes. Sixty healthy subjects (age 25 ± 4 yr; 29 men and 31 women) were enrolled in this study. All subjects underwent the supine temperature measurements of the bilateral forearms, brachial arterial blood pressure, HRV and RPP with a pulse analyzer in normothermic conditions, and thermal stresses. The power spectral low-frequency (LF) and high-frequency (HF) components of HRV decreased in the heat test and increased in the cold test. The heat stress significantly reduced radial augmentation index (AIr) (P < .05), but the cold stress significantly increased AIr (P < .01). The spectral energy of RPP did not show any statistical difference in 0 ~ 10 Hz region under both conditions, but in the region of 10 ~ 50 Hz, there was a significant increase (P < .01) in the heat test and a significant decrease in the cold test (P < .01). The changes in AIr induced by heat and cold stress were significantly negatively correlated with the spectral energy in the region of 10 ~ 50 Hz (SE10−50 Hz) but not in the region of 0 ~ 10 Hz (SE0−10 Hz). The results demonstrated that the SE10−50 Hz, which only possessed a small percentage in total pulse energy, presented more physiological characteristics than the SE0−10 Hz under the thermal stresses. PMID:21113292

Effect of cold rolling on the microstructural, magnetic, mechanical, and corrosion properties of AISI 316L austenitic stainless steel

NASA Astrophysics Data System (ADS)

Tanhaei, S.; Gheisari, Kh.; Alavi Zaree, S. R.

2018-06-01

This study has evaluated the effect of different levels of cold rolling (from 0 to 50%) on the microstructural, magnetic, and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in NaCl (1 mol/L) + H2SO4 (0.5 mol/L) solution. Microstructural examinations using optical microscopy revealed the development of a morphological texture from coaxial to elongated grains during the cold-rolling process. Phase analysis carried out on the basis of X-ray diffraction confirmed the formation of the ferromagnetic α'-martensite phase under the stresses applied during cold rolling. This finding is in agreement with magnetic measurements using a vibrating sample magnetometer. Mechanical properties determined by tensile and Vickers microhardness tests demonstrated an upward trend in the hardness-to-yield strength ratio with increasing cold-rolling percentage, representing a reduction in the material's work-hardening ability. Uniform and localized corrosion parameters were estimated via potentiodynamic polarization corrosion tests and electrochemical impedance spectroscopy. In contrast to the uniform corrosion, wherein the corrosion current density increased with increasing cold-working degree because of the high density of microstructural defects, the passive potential range and breakdown potential increased by cold working, showing greater resistance to pit nucleation. Although pits were formed, the cold-rolled material repassivation tendency decreased because of the broader hysteresis anodic loop, as confirmed experimentally by observation of the microscopic features after electrochemical cyclic polarization evaluations.

Additives for Water Mist Fire Suppression Systems: A Review

DTIC Science & Technology

2012-11-01

TM 2012-236; R & D pour la défense Canada – Atlantique; novembre 2012. Introduction : On utilisait les halons comme agents extincteurs dans les... 13 Table 11: Results of fire extinguishment tests on kerosene or heptanes pan fires using water mist and water mist with 2 vol...Forafac® WM. ....................................................... 13 x DRDC Atlantic TM 2012-236 This page intentionally left

LOFT, TAN650. Camera facing southeast. From left to right: stack ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LOFT, TAN-650. Camera facing southeast. From left to right: stack in distance, pre-amp wing, dome, north side of loft "service building." Note poured concrete wall of pre-amp wing on lower section; pumice block above. Date: May 2004. INEEL negative no. HD-39-19-3 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

40 CFR 600.113-08 - Fuel economy calculations for FTP, HFET, US06, SC03 and cold temperature FTP tests.

Code of Federal Regulations, 2012 CFR

2012-07-01

... economy values require input of the weighted grams/mile values for total hydrocarbons (HC), carbon... the weighted grams/mile values for the FTP test for HC, CO and CO2; and, additionally for methanol... paragraph (f) of this section. (2) Calculate separately the grams/mile values for the cold transient phase...

Mechanical Performance of Cold-Sprayed A357 Aluminum Alloy Coatings for Repair and Additive Manufacturing

NASA Astrophysics Data System (ADS)

Petráčková, K.; Kondás, J.; Guagliano, M.

2017-12-01

Cold-sprayed coatings made of A357 aluminum alloy, a casting alloy widely used in aerospace, underwent set of standard tests as well as newly developed fatigue test to gain an information about potential of cold spray for repair and additive manufacturing of loaded parts. With optimal spray parameters, coating deposition on substrate with smooth surface resulted in relatively good bonding, which can be further improved by application of grit blasting on substrate's surface. However, no enhancement of adhesion was obtained for shot-peened surface. Process temperature, which was set either to 450 or 550 °C, was shown to have an effect on adhesion and cohesion strength, but it does not influence residual stress in the coating. To assess cold spray perspectives for additive manufacturing, flat tensile specimens were machined from coating and tested in as-sprayed and heat-treated (solution treatment and aging) condition. Tensile properties of the coating after the treatment correspond to properties of the cast A357-T61 aluminum alloy. Finally, fatigue specimen was proposed to test overall performance of the coating and coating's fatigue limit is compared to the results obtained on cast A357-T61 aluminum alloy.

Thermal well-test method

DOEpatents

Tsang, C.F.; Doughty, C.A.

1984-02-24

A well-test method involving injection of hot (or cold) water into a groundwater aquifer, or injecting cold water into a geothermal reservoir is disclosed. By making temperature measurements at various depths in one or more observation wells, certain properties of the aquifer are determined. These properties, not obtainable from conventional well test procedures, include the permeability anisotropy, and layering in the aquifer, and in-situ thermal properties. The temperature measurements at various depths are obtained from thermistors mounted in the observation wells.

Thermal well-test method

DOEpatents

Tsang, Chin-Fu; Doughty, Christine A.

1985-01-01

A well-test method involving injection of hot (or cold) water into a groundwater aquifer, or injecting cold water into a geothermal reservoir. By making temperature measurements at various depths in one or more observation wells, certain properties of the aquifer are determined. These properties, not obtainable from conventional well test procedures, include the permeability anisotropy, and layering in the aquifer, and in-situ thermal properties. The temperature measurements at various depths are obtained from thermistors mounted in the observation wells.

Interethnic differences at the thermometric response to cold test: functional disorders of blood circulation in hand fingers and exposure to hand-arm vibration.

PubMed

Riolfi, A; Princivalle, A; Romeo, L; Caramaschi, P; Perbellini, L

2008-02-01

To report some notable aspects regarding thermometric response to cold test in black African subjects compared with Caucasians: both groups comprised persons exposed to hand-arm vibration and controls. An overall sample of 48 workers was examined in order to study their blood circulation in hand fingers: a control group of 12 healthy Caucasian workers never exposed before to hand-arm vibration; 12 Caucasian workers exposed for several years to vibrating tools and affected by occupational Raynaud's phenomenon; 12 healthy black African workers exposed to hand-arm vibration for almost 3 years; and 12 healthy black African workers never exposed to hand-arm vibration. Computerized skin thermometry was performed and thermometric curves were analyzed according to thermometric interpretation criteria such as the area-over-curve (AOC), the fifth minute of recovery/baseline temperature ratio (5REC/BT) and the temperature at the tenth minute of recovery (10REC) after cold test. Thermometric parameters in Caucasian subjects confirmed the basis of the existing literature in controls (basal finger temperature higher than 32 degrees C and complete recovery to the initial temperature after the cold test) and also in patients with Raynaud's phenomenon (basal temperature often lower than control subjects and slow recovery of finger temperature after cold test). Statistically significant difference was found between healthy Caucasians and healthy black subjects in all the parameters tested: healthy black subjects showed values of AOC and 10REC suggesting almost constantly lower finger temperatures during the thermometry test. Black people, both exposed and non-exposed to hand-arm vibration showed thermometric parameters suggesting poor blood microcirculation, which seems even poorer than in Caucasian people complaining Raynaud's phenomenon. Our chronothermometric tests suggest some significant interethnic differences in peripheral microcirculation, which seems rather poor in black African subjects in comparison with Caucasians.

Frequent Extreme Cold Exposure and Brown Fat and Cold-Induced Thermogenesis: A Study in a Monozygotic Twin

PubMed Central

Vosselman, Maarten J.; Vijgen, Guy H. E. J.; Kingma, Boris R. M.; Brans, Boudewijn; van Marken Lichtenbelt, Wouter D.

2014-01-01

Introduction Mild cold acclimation is known to increase brown adipose tissue (BAT) activity and cold-induced thermogenesis (CIT) in humans. We here tested the effect of a lifestyle with frequent exposure to extreme cold on BAT and CIT in a Dutch man known as ‘the Iceman’, who has multiple world records in withstanding extreme cold challenges. Furthermore, his monozygotic twin brother who has a ‘normal’ sedentary lifestyle without extreme cold exposures was measured. Methods The Iceman (subject A) and his brother (subject B) were studied during mild cold (13°C) and thermoneutral conditions (31°C). Measurements included BAT activity and respiratory muscle activity by [18F]FDG-PET/CT imaging and energy expenditure through indirect calorimetry. In addition, body temperatures, cardiovascular parameters, skin perfusion, and thermal sensation and comfort were measured. Finally, we determined polymorphisms for uncoupling protein-1 and β3-adrenergic receptor. Results Subjects had comparable BAT activity (A: 1144 SUVtotal and B: 1325 SUVtotal), within the range previously observed in young adult men. They were genotyped with the polymorphism for uncoupling protein-1 (G/G). CIT was relatively high (A: 40.1% and B: 41.9%), but unlike during our previous cold exposure tests in young adult men, here both subjects practiced a g-Tummo like breathing technique, which involves vigorous respiratory muscle activity. This was confirmed by high [18F]FDG-uptake in respiratory muscle. Conclusion No significant differences were found between the two subjects, indicating that a lifestyle with frequent exposures to extreme cold does not seem to affect BAT activity and CIT. In both subjects, BAT was not higher compared to earlier observations, whereas CIT was very high, suggesting that g-Tummo like breathing during cold exposure may cause additional heat production by vigorous isometric respiratory muscle contraction. The results must be interpreted with caution given the low subject number and the fact that both participants practised the g-Tummo like breathing technique. PMID:25014028

An Assessment of Cold Hardiness and Biochemical Adaptations for Cold Tolerance Among Different Geographic Populations of the Bactrocera dorsalis (Diptera: Tephritidae) in China

PubMed Central

Wang, Junhua; Zeng, Ling; Han, Zhaojun

2014-01-01

Abstract The cold hardiness of larvae, pupae, and adults of the oriental fruit fly, Bactrocera Dorsalis (Hendel) (Diptera: Tephritidae) was characterized first, and then body water, total sugar and glycerol contents, and activities of superoxide dismutase (SOD), catalase (CAT), peroxidase (POD), and alcohol dehydrogenase (ADH) of different geographical populations subjected to suitable rearing conditions and under sublethal low-temperature stress were compared. The cold hardiness of different populations was well correlated with the latitudes of distributions. The northern marginal population (31.6° N) had higher cold tolerance than southern populations (23.1° N and 24.3° N). Among different life stages, larvae had the least cold tolerance, whereas pupae had the most tolerance. Under suitable rearing conditions, the marginal population had lower activities of all four tested enzymes than that of the southern populations and also had lower body water and higher total sugar and glycerol contents. The low-temperature stress induced higher SOD, CAT, POD, and ADH activities of all tested life stages and of all tested populations with higher increase intensity in adults and pupae than in larvae. The increase intensity was higher in the marginal population than in the southern populations. Pupae in the marginal population and adults in the southern populations showed the largest activity enhancement, which agreed with the insect’s overwinter stages in their respective locations. Lower temperature stress lowered body water and total sugar contents and increased glycerol contents. The results revealed a strong correlation between the cold hardiness of a population and the concentration or activity of various biochemicals and enzymes known to be involved in cold tolerance. The marginal population of B. dorsalis might have evolved a new biotype with better adaption to low temperature. PMID:25527597

Miniature Joule Thomson (JT) CryoCoolers for Propellant Management

NASA Technical Reports Server (NTRS)

Kapat, Jay; Chow, Louis

2002-01-01

A proof-of-concept project is proposed here that would attempt to demonstrate how miniature cryocoolers can be used to chill the vacuum jacket line of a propellant transfer line and thus to achieve transfer line pre-chill, zero boil off and possible propellant densification. The project would be performed both at UCF and KSC, with all of the cryogenic testing taking place in the KSC cryogenic test bed. A LN2 line available in that KSC test facility would serve to simulate a LOX transfer line. Under this project, miniature and highly efficient cold heads would be designed. Two identical cold heads will be fabricated and then integrated with a JT-type cryogenic system (consisting of a common compressor and a common external heat exchanger). The two cold heads will be integrated into the vacuum jacket of a LN2 line in the KSC cryo lab, where the testing will take place.

Cold Helium Pressurization for Liquid Oxygen/Liquid Methane Propulsion Systems: Fully-Integrated Hot-Fire Test Results

NASA Technical Reports Server (NTRS)

Morehead, R. L.; Atwell, M. J.; Melcher, J. C.; Hurlbert, E. A.

2016-01-01

Hot-fire test demonstrations were successfully conducted using a cold helium pressurization system fully integrated into a liquid oxygen (LOX) / liquid methane (LCH4) propulsion system (Figure 1). Cold helium pressurant storage at near liquid nitrogen (LN2) temperatures (-275 F and colder) and used as a heated tank pressurant provides a substantial density advantage compared to ambient temperature storage. The increased storage density reduces helium pressurant tank size and mass, creating payload increases of 35% for small lunar-lander sized applications. This degree of mass reduction also enables pressure-fed propulsion systems for human-rated Mars ascent vehicle designs. Hot-fire test results from the highly-instrumented test bed will be used to demonstrate system performance and validate integrated models of the helium and propulsion systems. A pressurization performance metric will also be developed as a means to compare different active pressurization schemes.

Handling Ibuprofen Increases Pain Tolerance and Decreases Perceived Pain Intensity in a Cold Pressor Test

PubMed Central

Rutchick, Abraham M.; Slepian, Michael L.

2013-01-01

Pain contributes to health care costs, missed work and school, and lower quality of life. Extant research on psychological interventions for pain has focused primarily on developing skills that individuals can apply to manage their pain. Rather than examining internal factors that influence pain tolerance (e.g., pain management skills), the current work examines factors external to an individual that can increase pain tolerance. Specifically, the current study examined the nonconscious influence of exposure to meaningful objects on the perception of pain. Participants (N = 54) completed a cold pressor test, examined either ibuprofen or a control object, then completed another cold pressor test. In the second test, participants who previously examined ibuprofen reported experiencing less intense pain and tolerated immersion longer (relative to baseline) than those who examined the control object. Theoretical and applied implications of these findings are discussed. PMID:23469170

Origins of Negative Strain Rate Dependence of Stress Corrosion Cracking Initiation in Alloy 690, and Intergranular Crack Formation in Thermally Treated Alloy 690

NASA Astrophysics Data System (ADS)

Kim, Young Suk; Kim, Sung Soo

2016-09-01

We show that enhanced stress corrosion cracking (SCC) initiation in cold-rolled Alloy 690 with decreasing strain rate is related to the rate of short-range ordering (SRO) but not to the time-dependent corrosion process. Evidence for SRO is provided by aging tests on cold-rolled Alloy 690 at 623 K and 693 K (350 °C and 420 °C), respectively, which demonstrate its enhanced lattice contraction and hardness increase with aging temperature and time, respectively. Secondary intergranular cracks formed only in thermally treated and cold-rolled Alloy 690 during SCC tests, which are not SCC cracks, are caused by its lattice contraction by SRO before SCC tests but not by the orientation effect.

Anti-fungal activity of cold and hot water extracts of spices against fungal pathogens of Roselle (Hibiscus sabdariffa) in vitro.

PubMed

Touba, Eslaminejad Parizi; Zakaria, Maziah; Tahereh, Eslaminejad

2012-02-01

Crude extracts of seven spices, viz. cardamom, chilli, coriander, onion, garlic, ginger, and galangale were made using cold water and hot water extraction and they were tested for their anti-fungal effects against the three Roselle pathogens i.e. Phoma exigua, Fusarium nygamai and Rhizoctonia solani using the 'poisoned food technique'. All seven spices studied showed significant anti-fungal activity at three concentrations (10, 20 and 30% of the crude extract) in-vitro. The cold water extract of garlic exhibited good anti-fungal activity against all three tested fungi. In the case of the hot water extracts, garlic and ginger showed the best anti-fungal activity. Of the two extraction methods, cold water extraction was generally more effective than hot water extraction in controlling the pathogens. Against P. exigua, the 10% cold water extracts of galangale, ginger, coriander and cardamom achieved total (100%) inhibition of pathogen mycelial growth. Total inhibition of F. nygamai mycelial growth was similarly achieved with the 10% cold water extracts garlic. Against R. solani, the 10% cold water extract of galangale was effective in imposing 100% inhibition. Accordingly, the 10% galangale extract effectively controlled both P. exigua and R. solani in vitro. None of the hot water extracts of the spices succeeded in achieving 100% inhibition of the pathogen mycelial growth. Copyright © 2011 Elsevier Ltd. All rights reserved.

Comparative cold resistance of three Columbia River organisms. [Thermal stresses, fishes, Crustaceans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Becker, C.H.; Genoway, R.G.; Schneider, M.J.

1977-01-01

Resistance to abrupt and gradual cold shock was determined in bioassays with pumpkinseed (Lepomis gibbosus), rainbow trout (Salmo gairdneri) and a northwestern crayfish (Pacifastacus leniusculus) acclimated to higher temperatures at 5 C increments. Test criteria were median tolerance limits (TLm) for 96-h exposures after abrupt cold shock, and 50% loss of equilibrium (LE50) for decline rates of 18, 15, 10, 5 and 1 C/h during gradual cold shock. Cold resistance depended on original acclimation temperature (AT) and varied among species under both test conditions in the order: pumpkinseed < rainbow trout < crayfish. The lower TLm limit for pumpkinseed wasmore » 12.3 C at 30 C AT, 9.6 C at 25 C AT, 4.5 C at 20 C AT, and 2.7 C at 15 C AT. Rainbow trout at 20, 15 and 10 C AT survived abrupt exposures to cold down to 3.3, 1.4 and 0.5 C, respectively. Crayfish at 25, 20 and 15 C AT survived exposures down to 2.5, 0.4 and 0.0 C, respectively. TLm values were slightly above LE50 values for both fish species but well below for crayfish. Partial adaptation significantly lowered LE values at decline rates below 18 C/h for pumpkinseed, and to a lesser extent for the other two species, thus extending the lower margin of cold resistance.« less

Test of the SO(6) selection rule in 196Pt using cold-neutron capture

NASA Astrophysics Data System (ADS)

Jolie, J.; Régis, J.-M.; Wilmsen, D.; Saed-Samii, N.; Pfeiffer, M.; Warr, N.; Blanc, A.; Jentschel, M.; Köster, U.; Mutti, P.; Soldner, T.; Simpson, G. S.; De France, G.; Urban, W.; Drouet, F.; Vancraeyenest, A.; Bruce, A. M.; Roberts, O. J.; Fraile, L. M.; Paziy, V.; Ignatov, A.; Kröll, Th.; Ivanova, D.; Kisyov, S.; Lalkovski, S.; Podolyak, Zs.; Regan, P. H.; Wilson, E.; Korten, W.; Ur, C. A.; Lica, R.; Marginean, N.

2015-02-01

At the PF1B cold-neutron beam line of the Institut Laue Langevin, the EXILL&FATIMA array, consisting of EXOGAM Ge detectors and fast LaBr3(Ce) scintillators, was used to perform fast electronic timing measurements after the 195Pt(n, γ) reaction using a highly collimated cold-neutron beam. An upper lifetime limit was obtained for the third 0+ state in 196Pt. As this state is the lowest state of the σ = N - 2 set of SO(6) states, the selection rule which forbids E2 transitions to the lower lying σ = N could be tested.

Magnetic levitation and MHD propulsion

NASA Astrophysics Data System (ADS)

Tixador, P.

1994-04-01

Magnetic levitation and MHD propulsion are now attracting attention in several countries. Different superconducting MagLev and MHD systems will be described concentrating on, above all, the electromagnetic aspect. Some programmes occurring throughout the world will be described. Magnetic levitated trains could be the new high speed transportation system for the 21st century. Intensive studies involving MagLev trains using superconductivity have been carried out in Japan since 1970. The construction of a 43 km long track is to be the next step. In 1991 a six year programme was launched in the United States to evaluate the performances of MagLev systems for transportation. The MHD (MagnetoHydroDynamic) offers some interesting advantages (efficiency, stealth characteristics, ...) for naval propulsion and increasing attention is being paid towards it nowadays. Japan is also up at the top with the tests of Yamato I, a 260 ton MHD propulsed ship. Depuis quelques années nous assistons à un redémarrage de programmes concernant la lévitation et la propulsion supraconductrices. Différents systèmes supraconducteurs de lévitation et de propulsion seront décrits en examinant plus particulièrement l'aspect électromagnétique. Quelques programmes à travers le monde seront abordés. Les trains à sustentation magnétique pourraient constituer un nouveau mode de transport terrestre à vitesse élevée (500 km/h) pour le 21^e siècle. Les japonais n'ont cessé de s'intéresser à ce système avec bobine supraconductrice. Ils envisagent un stade préindustriel avec la construction d'une ligne de 43 km. En 1991 un programme américain pour une durée de six ans a été lancé pour évaluer les performances des systèmes à lévitation pour le transport aux Etats Unis. La MHD (Magnéto- Hydro-Dynamique) présente des avantages intéressants pour la propulsion navale et un regain d'intérêt apparaît à l'heure actuelle. Le japon se situe là encore à la pointe des développements actuels avec en particulier les premiers essais en rade de Kobe de Yamato I, navire de 260 tonnes, entraîné par MHD.

Smart FRP Composite Sandwich Bridge Decks in Cold Regions

DOT National Transportation Integrated Search

2011-07-01

In this study, new and integrated Smart honeycomb Fiber-Reinforced Polymer (S-FRP) : sandwich materials for various transportation construction applications, with particular emphasis : on highway bridge decks in cold regions, were developed and teste...

Echinacea purpurea: A Proprietary Extract of Echinacea purpurea Is Shown to be Safe and Effective in the Prevention of the Common Cold.

PubMed

Ross, Stephanie Maxine

2016-01-01

The research study in this review represents the largest clinical trial to date that evaluated the safety and efficacy of Echinacea purpurea for prophylactic treatment of the common cold, in addition to investigating its risk-benefit in a long-term treatment period. The clinical application of the proprietary standardized Echinacea purpurea extract(Echinaforce) demonstrated efficacy as a preventive cold treatment option over a 4-month duration. This study showed that Echinacea’s long-term prevention was associated with a reduction in the total number of cold episodes, a reduction in the number of days with colds, and a reduction in cold episodes requiring additional medication. Furthermore, the Echinacea test agent inhibited virally confirmed colds, exhibited maximal effects on recurrent infections, and demonstrated that its preventive effects increased relative to therapy compliance and adherence to the protocol. In summary, Echinacea purpurea when taken as recommended for the prevention of the common cold appears to provide a positive risk to benefit ratio.

Patients' experiences of cold exposure during ambulance care.

PubMed

Aléx, Jonas; Karlsson, Stig; Saveman, Britt-Inger

2013-06-06

Exposure to cold temperatures is often a neglected problem in prehospital care. Cold exposure increase thermal discomfort and, if untreated causes disturbances of vital body functions until ultimately reaching hypothermia. It may also impair cognitive function, increase pain and contribute to fear and an overall sense of dissatisfaction. The aim of this study was to investigate injured and ill patients' experiences of cold exposure and to identify related factors. During January to March 2011, 62 consecutively selected patients were observed when they were cared for by ambulance nursing staff in prehospital care in the north of Sweden. The field study was based on observations, questions about thermal discomfort and temperature measurements (mattress air and patients' finger temperature). Based on the observation protocol the participants were divided into two groups, one group that stated it was cold in the patient compartment in the ambulance and another group that did not. Continuous variables were analyzed with independent sample t-test, paired sample t-test and dichotomous variables with cross tabulation. In the ambulance 85% of the patients had a finger temperature below comfort zone and 44% experienced the ambient temperature in the patient compartment in the ambulance to be cold. There was a significant decrease in finger temperature from the first measurement indoor compared to measurement in the ambulance. The mattress temperature at the ambulance ranged from -22.3°C to 8.4°C. Cold exposure in winter time is common in prehospital care. Sick and injured patients immediately react to cold exposure with decreasing finger temperature and experience of discomfort from cold. Keeping the patient in the comfort zone is of great importance. Further studies are needed to increase knowledge which can be a base for implications in prehospital care for patients who probably already suffer for other reasons.

Simulation d'ecoulements internes compressibles laminaires et turbulents par une methode d'elements finis

NASA Astrophysics Data System (ADS)

Rebaine, Ali

1997-08-01

Ce travail consiste en la simulation numerique des ecoulements internes compressibles bidimensionnels laminaires et turbulents. On s'interesse, particulierement, aux ecoulements dans les ejecteurs supersoniques. Les equations de Navier-Stokes sont formulees sous forme conservative et utilisent, comme variables independantes, les variables dites enthalpiques a savoir: la pression statique, la quantite de mouvement et l'enthalpie totale specifique. Une formulation variationnelle stable des equations de Navier-Stokes est utilisee. Elle est base sur la methode SUPG (Streamline Upwinding Petrov Galerkin) et utilise un operateur de capture des forts gradients. Un modele de turbulence, pour la simulation des ecoulements dans les ejecteurs, est mis au point. Il consiste a separer deux regions distinctes: une region proche de la paroi solide, ou le modele de Baldwin et Lomax est utilise et l'autre, loin de la paroi, ou une formulation nouvelle, basee sur le modele de Schlichting pour les jets, est proposee. Une technique de calcul de la viscosite turbulente, sur un maillage non structure, est implementee. La discretisation dans l'espace de la forme variationnelle est faite a l'aide de la methode des elements finis en utilisant une approximation mixte: quadratique pour les composantes de la quantite de mouvement et de la vitesse et lineaire pour le reste des variables. La discretisation temporelle est effectuee par une methode de differences finies en utilisant le schema d'Euler implicite. Le systeme matriciel, resultant de la discretisation spatio-temporelle, est resolu a l'aide de l'algorithme GMRES en utilisant un preconditionneur diagonal. Les validations numeriques ont ete menees sur plusieurs types de tuyeres et ejecteurs. La principale validation consiste en la simulation de l'ecoulement dans l'ejecteur teste au centre de recherche NASA Lewis. Les resultats obtenus sont tres comparables avec ceux des travaux anterieurs et sont nettement superieurs concernant les ecoulements turbulents dans les ejecteurs.

One Dimensional Cold Rolling Effects on Stress Corrosion Crack Growth in Alloy 690 Tubing and Plate Materials

NASA Astrophysics Data System (ADS)

Toloczko, Mychailo B.; Olszta, Matthew J.; Bruemmer, Stephen M.

Stress corrosion crack-growth experiments have been performed on cold-rolled alloy 690 materials in simulated PWR primary water at 360°C. Extruded alloy 690 CRDM tubing in two conditions, thermally treated (TT) and solution annealed (SA), was cold rolled (CR) in one direction to several reductions reaching a maximum of 31% and tested in the S-L orientation. High stress corrosion cracking (SCC) propagation rates ( 8x10-8 mm/s) were observed for the 31%CR alloy 690TT material, while the 31%CR alloy 690SA exhibited 10X lower rates. The difference in intergranular SCC susceptibility appears to be related to grain boundary carbide distribution before cold rolling. SCC growth rates were found to depend on test temperature and hydrogen concentration. Tests were also performed on two alloy 690 plate heats, one CR to a reduction of 26% and the other to 20%. SCC growth rates at 360°C were similar to that measured for the 31%CR alloy 690TT CRDM tubing. Comparisons will be made to other results on CR alloy 690 materials.

Post-mortem detection of gasoline residues in lung tissue and heart blood of fire victims.

PubMed

Pahor, Kevin; Olson, Greg; Forbes, Shari L

2013-09-01

The purpose of this study was to determine whether gasoline residues could be detected post-mortem in lung tissue and heart blood of fire victims. The lungs and heart blood were investigated to determine whether they were suitable samples for collection and could be collected without contamination during an autopsy. Three sets of test subjects (pig carcasses) were investigated under two different fire scenarios. Test subjects 1 were anaesthetized following animal ethics approval, inhaled gasoline vapours for a short period and then euthanized. The carcasses were clothed and placed in a house where additional gasoline was poured onto the carcass post-mortem in one fire, but not in the other. Test subjects 2 did not inhale gasoline, were clothed and placed in the house and had gasoline poured onto them in both fires. Test subjects 3 were clothed but had no exposure to gasoline either ante- or post-mortem. Following controlled burns and suppression with water, the carcasses were collected, and their lungs and heart blood were excised at a necropsy. The headspace from the samples was analysed using thermal desorption-gas chromatography-mass spectroscopy. Gasoline was identified in the lungs and heart blood from the subjects that were exposed to gasoline vapours prior to death (test subjects 1). All other samples were negative for gasoline residues. These results suggest that it is useful to analyse for volatile ignitable liquids in lung tissue and blood as it may help to determine whether a victim was alive and inhaling gases at the time of a fire.

Influence du comportement des accompagnants sur le vécu des patients admis pour hémorragies digestives hautes au CHU campus de Lomé (Togo)

PubMed Central

Bagny, Aklesso; Dusabe, Angelique; Bouglouga, Oumboma; Lawson-ananisoh, Mawuli Late; Kaaga, Yeba Laconi; Djibril, Mohaman Awalou; Soedje, Kokou Mensah; Dassa, Simliwa Kolou; Redah, Datouda

2014-01-01

Introduction L'hémorragie digestive haute est une urgence, qui constitue souvent pour les patients un danger mortel suscitant inquiétude et agitation. Dans cet état, le patient dépend de ses accompagnants pour ses soins et pour honorer le traitement; mais souvent, il a été observé une discordance entre l'urgence et les comportements des accompagnants. Le but de cette étude était de décrire les facteurs socioéconomiques et psychologiques pouvant influencer les comportements des accompagnants des patients admis pour HDH, estimer l'indice de relation entre ces comportements et les facteurs associés d'une part et le vécu des patients admis pour HDH d'autre part. Méthodes Il s'agit d'une étude prospective menée de Septembre 2010 à Juin 2011 (soit 10 mois). Nous avions utilisé l'entretien semi-dirigé et l'observation directe pour collecter nos données, ces dernières avaient été traitées par les méthodes statistiques et d'analyse de contenu. Résultats Dans la présente étude, les comportements des accompagnants des patients admis pour HDH sont en majorité marqués par l'abandon (84%) et le manque de sollicitude (80,2%). Ces comportements sont souvent stimulés par les facteurs socioéconomiques tels que les difficultés économiques (83,2%), des conflits intrafamiliaux (85,1%) et des représentations (maladie incurable ou envoûtement) de la maladie par les accompagnants (73,3%) des cas. Quant aux patients, ils vivent ces comportements comme étant des menaces de mort ou des rejets (77,20%) et comme étant une dévalorisation ou une humiliation de la part de leurs accompagnants (70,30%). Les résultats confirment l'existence de lien significatif entre les comportements des accompagnants et les facteurs socio économiques, entre les comportements des accompagnants et des facteurs psychologiques, et entre le vécu des patients admis pour l'HDH et les comportements des accompagnants. Conclusion Des études ultérieures devraient aborder les points non touchés dans cette étude. Certes, elle a apporté un plus dans la compréhension du vécu des patients admis pour HDH et des comportements de leurs accompagnants. Cependant, elle est loin d'avoir épuisé les différents contours de la problématique de la présente étude. PMID:25848453

Gestion des ressources hydriques adaptee aux changements climatiques pour la production optimale d'hydroelectricite. Etude de cas: Bassin versant de la riviere Manicouagan

NASA Astrophysics Data System (ADS)

Haguma, Didier

Il est dorenavant etabli que les changements climatiques auront des repercussions sur les ressources en eau. La situation est preoccupante pour le secteur de production d'energie hydroelectrique, car l'eau constitue le moteur pour generer cette forme d'energie. Il sera important d'adapter les regles de gestion et/ou les installations des systemes hydriques, afin de minimiser les impacts negatifs et/ou pour capitaliser sur les retombees positives que les changements climatiques pourront apporter. Les travaux de la presente recherche s'interessent au developpement d'une methode de gestion des systemes hydriques qui tient compte des projections climatiques pour mieux anticiper les impacts de l'evolution du climat sur la production d'hydroelectricite et d'etablir des strategies d'adaptation aux changements climatiques. Le domaine d'etude est le bassin versant de la riviere Manicouagan situe dans la partie centrale du Quebec. Une nouvelle approche d'optimisation des ressources hydriques dans le contexte des changements climatiques est proposee. L'approche traite le probleme de la saisonnalite et de la non-stationnarite du climat d'une maniere explicite pour representer l'incertitude rattachee a un ensemble des projections climatiques. Cette approche permet d'integrer les projections climatiques dans le probleme d'optimisation des ressources en eau pour une gestion a long terme des systemes hydriques et de developper des strategies d'adaptation de ces systemes aux changements climatiques. Les resultats montrent que les impacts des changements climatiques sur le regime hydrologique du bassin de la riviere Manicouagan seraient le devancement et l'attenuation de la crue printaniere et l'augmentation du volume annuel d'apports. L'adaptation des regles de gestion du systeme hydrique engendrerait une hausse de la production hydroelectrique. Neanmoins, une perte de la performance des installations existantes du systeme hydrique serait observee a cause de l'augmentation des deversements non productibles dans le climat futur. Des strategies d'adaptation structurale ont ete analysees pour augmenter la capacite de production et la capacite d'ecoulement de certaines centrales hydroelectriques afin d'ameliorer la performance du systeme. Une analyse economique a permis de choisir les meilleures mesures d'adaptation et de determiner le moment opportun pour la mise en oeuvre de ces mesures. Les resultats de la recherche offrent aux gestionnaires des systemes hydriques un outil qui permet de mieux anticiper les consequences des changements climatiques sur la production hydroelectrique, incluant le rendement de centrales, les deversements non productibles et le moment le plus opportun pour inclure des modifications aux systemes hydriques. Mots-cles : systemes hydriques, adaptation aux changements climatiques, riviere Manicouagan

Finalize field testing of cold climate heat pump (CCHP) based on tandem vapor injection compressors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen, Bo; Baxter, Van D.; Abdelaziz, Omar

2017-03-01

This report describes the system diagram and control algorithm of a prototype air-source cold climate heat pump (CCHP) using tandem vapor injection (VI) compressors. The prototype was installed in Fairbanks, Alaska and underwent field testing starting in 09/2016. The field testing results of the past six months, including compressor run time fractions, measured COPs and heating capacities, etc., are presented as a function of the ambient temperature. Two lessons learned are also reported.

40 CFR 600.113-08 - Fuel economy calculations for FTP, HFET, US06, SC03 and cold temperature FTP tests.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy calculations for FTP, HFET, US06, SC03 and cold temperature FTP tests. 600.113-08 Section 600.113-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy...

Comparing the Robustness of High-Frequency Traveling-Wave Tube Slow-Wave Circuits

NASA Technical Reports Server (NTRS)

Chevalier, Christine T.; Wilson, Jeffrey D.; Kory, Carol L.

2007-01-01

A three-dimensional electromagnetic field simulation software package was used to compute the cold-test parameters, phase velocity, on-axis interaction impedance, and attenuation, for several high-frequency traveling-wave tube slow-wave circuit geometries. This research effort determined the effects of variations in circuit dimensions on cold-test performance. The parameter variations were based on the tolerances of conventional micromachining techniques.

40 CFR Appendix Xvi to Part 86 - Pollutant Mass Emissions Calculation Procedure for Gaseous-Fueled Vehicles and for Vehicles...

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Where: Ywm = Weighted mass emissions of each pollutant, i.e., HC, CO, NOX or CO , in grams per vehicle mile. Yct = Mass emissions as calculated from the “transient” phase of the cold start test, in grams... grams per test phase. Ys = Mass emissions as calculated from the “stabilized” phase of the cold start...

40 CFR Appendix Xvi to Part 86 - Pollutant Mass Emissions Calculation Procedure for Gaseous-Fueled Vehicles and for Vehicles...

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Where: Ywm = Weighted mass emissions of each pollutant, i.e., HC, CO, NOX or CO , in grams per vehicle mile. Yct = Mass emissions as calculated from the “transient” phase of the cold start test, in grams... grams per test phase. Ys = Mass emissions as calculated from the “stabilized” phase of the cold start...

40 CFR Appendix Xvi to Part 86 - Pollutant Mass Emissions Calculation Procedure for Gaseous-Fueled Vehicles and for Vehicles...

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Where: Ywm = Weighted mass emissions of each pollutant, i.e., HC, CO, NOX or CO , in grams per vehicle mile. Yct = Mass emissions as calculated from the “transient” phase of the cold start test, in grams... grams per test phase. Ys = Mass emissions as calculated from the “stabilized” phase of the cold start...

40 CFR Appendix Xvi to Part 86 - Pollutant Mass Emissions Calculation Procedure for Gaseous-Fueled Vehicles and for Vehicles...

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Where: Ywm = Weighted mass emissions of each pollutant, i.e., HC, CO, NOX or CO , in grams per vehicle mile. Yct = Mass emissions as calculated from the “transient” phase of the cold start test, in grams... grams per test phase. Ys = Mass emissions as calculated from the “stabilized” phase of the cold start...

Caloric stimulation

MedlinePlus

... differences in temperature to diagnose damage to the acoustic nerve. This is the nerve that is involved ... This test stimulates your acoustic nerve by delivering cold or warm water or air into your ear canal. When cold water or air enters your ...

14. INTERIOR VIEW TO THE SOUTH OF ROOM 136, COLD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. INTERIOR VIEW TO THE SOUTH OF ROOM 136, COLD ASSEMBLY BAY NO. 2. - Nevada Test Site, Reactor Maintenance Assembly & Dissassembly Facility, Area 25, Jackass Flats, Junction of Roads F & G, Mercury, Nye County, NV

13. INTERIOR VIEW TO THE SOUTHEAST OF ROOM 101, COLD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. INTERIOR VIEW TO THE SOUTHEAST OF ROOM 101, COLD ASSEMBLY BAY NO. 1. - Nevada Test Site, Reactor Maintenance Assembly & Dissassembly Facility, Area 25, Jackass Flats, Junction of Roads F & G, Mercury, Nye County, NV

Smart FRP Composite Sandwich Bridge Decks in Cold Regions

DOT National Transportation Integrated Search

2011-07-01

In this study, new and integrated Smart honeycomb Fiber-Reinforced Polymer (S-FRP) sandwich materials for various transportation construction applications, with particular emphasis on highway bridge decks in cold regions, were developed and tested. T...

2. CATCH BASIN, INFLOW PIPES AT CENTER, COLD FLOW LABORATORY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. CATCH BASIN, INFLOW PIPES AT CENTER, COLD FLOW LABORATORY AT LEFT, VIEW TOWARDS NORTHWEST. - Glenn L. Martin Company, Titan Missile Test Facilities, Catch Basin, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Building Resilient Communities Workshop Report

DTIC Science & Technology

2014-06-01

Reine (en droit du Canada), telle que représentée par le ministre de la Défense nationale, 2014 CSSP-2013-CD-1120...EMBC) [ Gestion des urgences Colombie-Britannique], le Programme canadien pour la sûreté et la sécurité (PCSS) et Recherche et développement pour la ...comptes rendus de la mise à jour du rapport du RCERD sur la résilience des communautés autochtones. L’événement a aussi donné une tribune pour un groupe

Behavior Characteristics of Type I (75/25) Octol during Melt Pouring HE Warhead M250 (Chaparral)

DTIC Science & Technology

1979-09-01

COVERED BEHAVIOR CHARACTERISTICS OF TYPE 1 (75/25) "OCTOL DURING MELT POURING HE WARHEAD I M250 (CHAPARRAL) 6. PERFORMING ORG. APrPORT NUMBER 7. AUTHOR...Military Specification, HMX, MIL-H-45444B, Amendment 2, dated 12 July 1977. 4 6. Military Specification, Warhead, Guided Missile, HE, M250 , Loading...CHARACTERISTICS OF TYPE i (75/25) OCTOL DURING MELT POURING HE WARHEAD M250 (CHAPARRAL) HERMAN J. FRIGAND SEPTEMBER 1979 US ARMY ARMAMENT RESEARCH AND

Urban Combat Advanced Training Technology Architecture (Architecture de technologie avancee pour l’entrainement au combat urbain)

DTIC Science & Technology

2018-01-01

REPORT TR-MSG-098 Urban Combat Advanced Training Technology Architecture (Architecture de technologie avancée pour l’entraînement au combat urbain...REPORT TR-MSG-098 Urban Combat Advanced Training Technology Architecture (Architecture de technologie avancée pour l’entraînement au combat...3 1-2 1.3 Illustration of the Need for UCATT by Contemporary Example Situations 1-3 1.3.1 RNLA: Connection of NLD Mobile Combat Training Centre to

Inauguration LEP

ScienceCinema

None

2017-12-09

Le DG C.Rubbia remercie son prédécesseur H.Schopper pour sa contribution pour la réalisation du LEP. En présence du président de la Confédération Suisse, Mons. Délamuraz et du président français Mons.Mitterand plusieurs discours sont donnés et les délégations invités pour un déjeuner.

Evaluating the effects of hydroxyapatite coating on the corrosion behavior of severely deformed 316Ti SS for surgical implants.

PubMed

Mhaede, Mansour; Ahmed, Aymen; Wollmann, Manfred; Wagner, Lothar

2015-05-01

The present work investigates the effects of severe plastic deformation by cold rolling on the microstructure, the mechanical properties and the corrosion behavior of austenitic stainless steel (SS) 316Ti. Hydroxyapatite coating (HA) was applied on the deformed material to improve their corrosion resistance. The martensitic transformation due to cold rolling was recorded by X-ray diffraction spectra. The effects of cold rolling on the corrosion behavior were studied using potentiodynamic polarization. The electrochemical tests were carried out in Ringer's solution at 37±1 °C. Cold rolling markedly enhanced the mechanical properties while the electrochemical tests referred to a lower corrosion resistance of the deformed material. The best combination of both high strength and good corrosion resistance was achieved after applying hydroxyapatite coating. Copyright © 2015 Elsevier B.V. All rights reserved.

Porous hydroxyapatite/gelatine scaffolds with ice-designed channel-like porosity for biomedical applications.

PubMed

Landi, Elena; Valentini, Federica; Tampieri, Anna

2008-11-01

A cryogenic process, including freeze-casting and drying has been performed to obtain hydroxyapatite (HA) scaffolds (approx. diameter 10 mm, height 20 mm) with completely lamellar morphology due to preferentially aligned channel-like pores. Changing the process parameters that influence the cold transmission efficiency from the bottom to the top of the poured HA slurry, lamellar ice crystals with different thickness grew throughout the samples. After sintering, scaffolds with porosity features nearly resembling the ice ones were obtained. The interconnection of pores and the ability of the scaffolds to be rapidly penetrated by synthetic body fluid has been proven. Biohybrid HA/gel composites were prepared, infiltrating HA lamellar scaffolds (45-55 vol.% of porosity) with a 10wt.% solution of gelatine. Colouring genipine was used to cross-link gelatine and clearly show the distribution of the protein in the composite. The compressive mechanical properties of lamellar scaffolds improved with the addition of gelatine: the strength increased up to 5-6 times, while the elastic modulus and strain approximately doubled. The effectiveness of the cross-linkage has been preliminarily verified following scaffold degradation in synthetic body fluid.

Gating geometry studies of thin-walled 17-4PH investment castings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maguire, M.C.; Zanner, F.J.

1992-11-01

The ability to design gating systems that reliably feed and support investment castings is often the result of ``cut-and-try`` methodology. Factors such as hot tearing, porosity, cold shuts, misruns, and shrink are defects often corrected by several empirical gating design iterations. Sandia National Laboratories is developing rules that aid in removing the uncertainty involved in the design of gating systems for investment castings. In this work, gating geometries used for filling of thin walled investment cast 17-4PH stainless steel flat plates were investigated. A full factorial experiment evaluating the influence of metal pour temperature, mold preheat temperature, and mold channelmore » thickness were conducted for orientations that filled a horizontal flat plate from the edge. A single wedge gate geometry was used for the edge-gated configuration. Thermocouples placed along the top of the mold recorded metal front temperatures, and a real-time x-ray imaging system tracked the fluid flow behavior during filling of the casting. Data from these experiments were used to determine the terminal fill volumes and terminal fill times for each gate design.« less

Gating geometry studies of thin-walled 17-4PH investment castings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maguire, M.C.; Zanner, F.J.

1992-01-01

The ability to design gating systems that reliably feed and support investment castings is often the result of cut-and-try'' methodology. Factors such as hot tearing, porosity, cold shuts, misruns, and shrink are defects often corrected by several empirical gating design iterations. Sandia National Laboratories is developing rules that aid in removing the uncertainty involved in the design of gating systems for investment castings. In this work, gating geometries used for filling of thin walled investment cast 17-4PH stainless steel flat plates were investigated. A full factorial experiment evaluating the influence of metal pour temperature, mold preheat temperature, and mold channelmore » thickness were conducted for orientations that filled a horizontal flat plate from the edge. A single wedge gate geometry was used for the edge-gated configuration. Thermocouples placed along the top of the mold recorded metal front temperatures, and a real-time x-ray imaging system tracked the fluid flow behavior during filling of the casting. Data from these experiments were used to determine the terminal fill volumes and terminal fill times for each gate design.« less

Haze over eastern China

NASA Image and Video Library

2015-10-26

On October 17, 2015, the Moderate Resolution Imaging Spectroradiometer (MODIS) aboard NASA’s Terra satellite captured this true-color image of a thick haze hanging over eastern China. In the north, the large city of Beijing is completely obscured from view, as is much of the landscape. The haze thins slightly over the Bohai Sea. Further south, sediment pours into the East China Sea near the city of Shanghai. Heavy haze is common in this region, and tends to worsen in October through January, when cold, heavy air traps pollutants near the surface of the Earth. It is likely that this scene was caused by such a temperature inversion. Normally, air is warmest near the surface of the Earth. But sometimes a mass of warm air will move the cooler air, so the atmosphere actually warms with the altitude. Cool air does not have energy to rise through the warm air, vertical circulation slows and air becomes trapped near the surface. Any pollution that is emitted into the cooler air will also get trapped, increasing low-level air pollution and haze. Credit: NASA/GSFC/Jeff Schmaltz/MODIS Land Rapid Response Team

The induction of menadione stress tolerance in the marine microalga, Dunaliella viridis, through cold pretreatment and modulation of the ascorbate and glutathione pools.

PubMed

Madadkar Haghjou, Maryam; Colville, Louise; Smirnoff, Nicholas

2014-11-01

The effect of cold pretreatment on menadione tolerance was investigated in the cells of the marine microalga, Dunaliella viridis. In addition, the involvement of ascorbate and glutathione in the response to menadione stress was tested by treating cell suspensions with l-galactono-1,4-lactone, an ascorbate precursor, and buthionine sulfoximine, an inhibitor of glutathione synthesis. Menadione was highly toxic to non cold-pretreated cells, and caused a large decrease in cell number. Cold pretreatment alleviated menadione toxicity and cold pretreated cells accumulated lower levels of reactive oxygen species, and had enhanced antioxidant capacity due to increased levels of β-carotene, reduced ascorbate and total glutathione compared to non cold-pretreated cells. Cold pretreatment also altered the response to l-galactono-1,4-lactone and buthionine sulfoximine treatments. Combined l-galactono-1,4-lactone and menadione treatment was lethal in non-cold pretreated cells, but in cold-pretreated cells it had a positive effect on cell numbers compared to menadione alone. Overall, exposure of Dunaliella cells to cold stress enhanced tolerance to subsequent oxidative stress induced by menadione. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Quantitative sensory studies in complex regional pain syndrome type 1/RSD.

PubMed

Tahmoush, A J; Schwartzman, R J; Hopp, J L; Grothusen, J R

2000-12-01

Patients with complex regional pain syndrome type I (CRPSD1) may have thermal allodynia after application of a non-noxious thermal stimulus to the affected limb. We measured the warm, cold, heat-evoked pain threshold and the cold-evoked pain threshold in the affected area of 16 control patients and patients with complex regional pain syndrome type 1/RSD to test the hypothesis that allodynia results from an abnormality in sensory physiology. A contact thermode was used to apply a constant 1 degrees C/second increasing (warm and heat-evoked pain) or decreasing (cold and cold-evoked pain) thermal stimulus until the patient pressed the response button to show that a temperature change was felt by the patient. Student t test was used to compare thresholds in patients and control patients. The cold-evoked pain threshold in patients with CRPSD1/RSD (p <0.001) was significantly decreased when compared with the thresholds in control patients (i.e., a smaller decrease in temperature was necessary to elicit cold-pain in patients with CRPSD1/RSD than in control patients). The heat-evoked pain threshold in patients with CRPS1/RSD was (p <0.05) decreased significantly when compared with thresholds in control patients. The warm- and cold-detection thresholds in patients with CRPS1/RSD were similar to the thresholds in control patients. This study suggests that thermal allodynia in patients with CRPS1/RSD results from decreased cold-evoked and heat-evoked pain thresholds. The thermal pain thresholds are reset (decreased) so that non-noxious thermal stimuli are perceived to be pain (allodynia).

61. photographer unknown undated FIRST CONCRETE BEING POURED IN DRAFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

61. photographer unknown undated FIRST CONCRETE BEING POURED IN DRAFT TUBE FLOOR SLAB. - Bonneville Project, Powerhouse No.1, Spanning Bradford Slough, from Bradford Island, Bonneville, Multnomah County, OR

Neurological Assessment Using a Quantitative Sensory Test in Patients with Chronic Unilateral Orofacial Pain.

PubMed

Salame, Talal H; Blinkhorn, Antony; Karami, Zahra

2018-01-01

Quantitative Sensory Testing (QST) has been used in clinical and experimental settings to establish sensory assessment for different types of pains, and may be a useful tool for the assessment of orofacial pain, but this premise needs to be tested. The aim of the study was to evaluate responses to thermal stimuli between painful and non-painful facial sites in subjects with orofacial pain using QST. A total of 60 participants (5o females: 28-83 years; 10 males: 44-81 years) with unilateral orofacial pain were recruited from the Orofacial Pain Clinic at the Pain Management and Research Centre, Royal North Shore Hospital, Sydney, Australia. The study followed the methods of limits of the German Research Network testing four modalities of thermal thresholds, the Warm Sensation, the Cold Sensation, the Heat Pain and the Cold Pain using a TSA-II Neurosensory Analyser. The results were compared to the results from the unaffected side of the same patient on the same area and a single t test statistical analysis was performed, where a p value of less than 0.05 was considered significant. The Mean Difference for Cold Sensation between the pain side and the non-pain side was 0.48 °C ± 1.5 (t= 2.466, p=0.017), 0.68 °C ± 2.04 for Warm Sensation (t= -2.573, p= 0.013), 2.56 °C ± 2.74 for Cold Pain (t= 7.238, p<0.001) and -1.21 °C ± 2.59 for Hot Pain (t= -3.639, p=0.001). The study showed that QST methods using thermal stimuli could be used to evaluate sensory dysfunction in orofacial pain patients using the specific parameters of cool and warm sensation, and cold and hot pain.

Feasibility and repeatability of cold and mechanical quantitative sensory testing in normal dogs

PubMed Central

Briley, Jessica D.; Williams, Morika D.; Freire, Mila; Griffith, Emily H.; Lascelles, B. Duncan X.

2015-01-01

Feasibility and inter-session repeatability of cold and mechanical quantitative sensory testing (QST) were assessed in 24 normal dogs. Cold thermal latencies were evaluated using a thermal probe (0 °C) applied to three pelvic limb sites. Mechanical thresholds were measured using an electronic von Frey anesthesiometer (EVF) and a blunt-probed pressure algometer (PA) applied to the dorsal aspect of the metatarsus. All QST trials were performed with dogs in lateral recumbency. Collection of cold QST data was easy (feasible) in 19/24 (79%) dogs. However, only 18.4%, 18.9% and 13.2% of cold QST trials elicited a response at the medial tibia, third digital pad and plantar metatarsal regions, respectively. Collection of mechanical QST data was easy (feasible) in 20/24 (83%) dogs for both EVF and PA. At consecutive sampling times, approximately 2 weeks apart, the average EVF sensory thresholds were 414 ± 186 g and 379 ± 166 g, respectively, and the average PA sensory thresholds were 1089 ± 414 g and 1028 ± 331 g, respectively. There was no significant difference in inter-session or inter-limb threshold values for either mechanical QST device. The cold QST protocol in this study was achievable, but did not provide consistently quantifiable results. Both mechanical QST devices tested provided repeatable, reliable sensory threshold measurements in normal, client-owned dogs. These findings contribute to the validation of the EVF and PA as tools to obtain repeated QST data over time in dogs to assess somatosensory processing changes. PMID:24268475

Superconducting 112 MHz QWR electron gun

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belomestnykh, S.; Ben-Zvi, I.; Boulware, C.H.

Brookhaven National Laboratory and Niowave, Inc. have designed and fabricated a superconducting 112 MHz quarter-wave resonator (QWR) electron gun. The first cold test of the QWR cryomodule has been completed at Niowave. The paper describes the cryomodule design, presents the cold test results, and outline plans to upgrade the cryomodule. Future experiments include studies of different photocathodes and use for the coherent electron cooling proof-of-principle experiment. Two cathode stalk options, one for multi-alkali photocathodes and the other one for a diamond-amplified photocathode, are discussed. A quarter-wave resonator concept of superconducting RF (SRF) electron gun was proposed at BNL for electronmore » cooling hadron beams in RHIC. QWRs can be made sufficiently compact even at low RF frequencies (long wavelengths). The long wavelength allows to produce long electron bunches, thus minimizing space charge effects and enabling high bunch charge. Also, such guns should be suitable for experiments requiring high average current electron beams. A 112 MHz QWR gun was designed, fabricated, and cold-tested in collaboration between BNL and Niowave. This is the lowest frequency SRF gun ever tested successfully. In this paper we describe the gun design and fabrication, present the cold test results, and outline our plans. This gun will also serve as a prototype for a future SRF gun to be used for coherent electron cooling of hadrons in eRHIC.« less

60. photographer unknown undated CONCRETE BEING POURED ON CENTER PORTION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. photographer unknown undated CONCRETE BEING POURED ON CENTER PORTION OF DRAFT TUBE FLOOR SLAB. - Bonneville Project, Powerhouse No.1, Spanning Bradford Slough, from Bradford Island, Bonneville, Multnomah County, OR

Adaptation of a Turbine Test Facility to High-Temperature Research (Adaptation d’un banc de Turbine aux Recherches pour les Hautes Temperatures,

DTIC Science & Technology

1980-12-19

Des hautes temperatures devant turbine sur turborgacteur et turbines A gaz. (High turbine inlet temperatures in turbo - jet engines and gas turbines ... turbo - jet engines .) Revue Gn(rale de Thermique, No. 166, October 1975 15 D. Arnal Etude exprimentale et thgorique de la transition de la couche J.C...r AD-AIOl 374 ROYAL AIRCRAFT ESTABLISHMENT FARNBOROUBH (ENGLAND) F/B 10/1 ADAPTATION OF A TURBINE TEST FACILITY TO HIGH-TEMPERATURE RESEA--ETC(U) DEC

Refrigeration is not necessary for measurement of uric acid in patients treated with rasburicase.

PubMed

Lindeman, Neal I; Melanson, Stacy E F; McDonnell, Anne; DeAngelo, Daniel J; Jarolim, Petr

2013-05-01

Rasburicase, used for hyperuricemia of tumor lysis syndrome, retains activity at room temperature (RT) in in vitro studies. Cold-temperature handling is recommended for uric acid measurements in patients receiving rasburicase: collection in prechilled tubes, transportation on ice, and 4°C centrifugation. We performed a prospective study of these requirements. A total of 65 pairs of blood samples were collected from 34 patients, 12-24 h after receiving rasburicase. The effect of temperature on uric acid concentration was tested on paired samples handled either at RT or when cold: centrifugation (18 sample pairs), collection tube (14 pairs), transportation (24 pairs), and nine pairs were retested after 1 h at RT. No significant temperature effect was seen on the uric acid measurements for any of the cold-handling steps: proportional, absolute biases were -1.4%, -0.06 mg/dL (centrifugation), -1.5%, +0.02 mg/dL (tube temperature), and -2.2%, -0.01 mg/dL (transportation). A 20% negative bias was seen in samples retested after 1 h at RT. Cold handling (prechilled tubes, iced transportation, 4°C centrifugation) was equivalent to RT for immediate measurement. An additional 1 h delay at RT led to a 20% decrease in uric acid. The cold handling measures required by the manufacturer are not necessary for uric acid testing of patients receiving rasburicase treatment, if testing is performed without delay.

A personal sampler for aircraft engine cold start particles: laboratory development and testing.

PubMed

Armendariz, Alfredo; Leith, David

2003-01-01

Industrial hygienists in the U.S. Air Force are concerned about exposure of their personnel to jet fuel. One potential source of exposure for flightline ground crews is the plume emitted during the start of aircraft engines in extremely cold weather. The purpose of this study was to investigate a personal sampler, a small tube-and-wire electrostatic precipitator (ESP), for assessing exposure to aircraft engine cold start particles. Tests were performed in the laboratory to characterize the sampler's collection efficiency and to determine the magnitude of adsorption and evaporation artifacts. A low-temperature chamber was developed for the artifact experiments so tests could be performed at temperatures similar to actual field conditions. The ESP collected particles from 0.5 to 20 micro m diameter with greater than 98% efficiency at particle concentrations up to 100 mg/m(3). Adsorption artifacts were less than 5 micro g/m(3) when sampling a high concentration vapor stream. Evaporation artifacts were significantly lower for the ESP than for PVC membrane filters across a range of sampling times and incoming vapor concentrations. These tests indicate that the ESP provides more accurate exposure assessment results than traditional filter-based particle samplers when sampling cold start particles produced by an aircraft engine.

Sandia National Laboratories, Tonopah Test Range Fire Control Bunker (Building 09-51): Photographs and Written Historical and Descriptive Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ullrich, Rebecca A.

The Fire Control Bunker (Building 09-51) is a contributing element to the Sandia National Laboratories (SNL) Tonopah Test Range (TTR) Historic District. The SNL TTR Historic District played a significant role in U.S. Cold War history in the areas of stockpile surveillance and non-nuclear field testing of nuclear weapons design. The district covers approximately 179,200 acres and illustrates Cold War development testing of nuclear weapons components and systems. This report includes historical information, architectural information, sources of information, project information, maps, blueprints, and photographs.

Sandia National Laboratories, Tonopah Test Range Assembly Building 9B (Building 09-54): Photographs and Written Historical and Descriptive Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ullrich, Rebecca A.

Assembly Building 9B (Building 09-54) is a contributing element to the Sandia National Laboratories (SNL) Tonopah Test Range (TTR) Historic District. The SNL TTR Historic District played a significant role in U.S. Cold War history in the areas of stockpile surveillance and non-nuclear field testing of nuclear weapons designs. The district covers approximately 179,200 acres and illustrates Cold War development testing of nuclear weapons components and systems. This report includes historical information, architectural information, sources of information, project information, maps, blueprints, and photographs.

Problématique de l'utilisation des Moustiquaires Imprégnées d'insecticide à Longue Durée (MILD) chez les enfants de moins de 5 ans en République Démocratique du Congo

PubMed Central

Philippe, Cilundika Mulenga; Odile, Nyota Nsenga; Numbi, Oscar Luboya

2016-01-01

Introduction Le paludisme est une maladie parasitaire à transmission vectorielle qui constitue un problème majeur de santé publique dans les pays tropicaux, particulièrement les pays de l'Afrique Subsaharienne. La présente étude avait pour objectif d'identifier le niveau d'utilisation de la MILD chez les enfants de moins de 5 ans dans la zone de santé de Mumbunda. Méthodes L’étude, de type transversal, a été mené du 25 au 27 octobre 2013 et a porté sur un échantillon de 410 ménages tirés au hasard et ayant au moins un enfant de moins de 5 ans. Résultats Parmi les ménages qui avaient déclaré possédaient la MILD 13,1% (n=54) des répondant avaient déclaré les utilisé chez les enfants de moins de 5ans et 80,2% pour tout le monde. Dans 22,0% des cas, les répondants ont évoqué le manque d'argent comme motif de la non possession de la MILD. Les répondants savaient déclarer à 79,8% avoir utilisé la MILD pour se protéger contre la malaria et à 66,3% pour se protéger contre les piqures des moustiques. La MILD a été étalée à l'ombre pendant 24h avant d’être utilisée pour la première fois par 77,9% des ménages. Les répondants avaient déclaré à 15,3% (n=63) avoir reçu les conseils par les médias pour l'usage de la moustiquaire. Et le personnel médical était la source la plus importante pour expliquer le mode d'emploi de la MILD pour 51,2% des ménages. Conclusion La réussite pour faire reculer le paludisme doit nécessairement passer par la prévention, le suivi et l’évaluation de l'utilisation des moustiquaires imprégnées au niveau de la zone de santé de Mumbunda. PMID:27222690

Synthese et Caracterisation de Nanocomposites d'Argile et de Graphene Formes a Partir de Precurseurs Organiques =

NASA Astrophysics Data System (ADS)

Boussaboun, Zakariae

Les mineraux d'argile sont des catalyseurs possibles pour la formation du graphene a partir de precurseurs organiques, comme le saccharose. Les argiles sont abondantes, securitaires et economiques pour la formation du graphene. L'objectif principal de ce memoire est de demontrer qu'il est possible de synthetiser un materiau hybride contenant de l'argile et du graphene. La preparation de ces materiaux carbones a base de l'argile (bentonite et cloisite) et le saccharose a ete realisee selon deux methodes. La premiere methode est faite en trois etapes : 1) periode de contact entre l'argile et la source de carbone dans un environnement humide, 2) infiltration de la matiere carbonee et transformation au four a micro-onde, 3) chauffage a 750°C sous azote pour obtenir des materiaux carbones. Par contre la deuxieme methode est faite en deux etapes, sans micro-onde, et avec une augmentation de la quantite de source de carbone (saccharose et alginate). La caracterisation du materiau a permis de suivre les reactions de transformation de la source de carbone vers le graphene. Cette caracterisation a ete faite par la spectroscopie IRTF et Raman, l'analyse thermogravimetrique (TGA), la surface specifique (methode BET) et le microscope electronique a balayage (MEB). La conductivite electrique a ete mesuree par un spectrometre dielectrique et en fonction de la pression appliquee avec un multimetre. Le materiau realise etait incorpore dans une matrice avec un polyethylene a basse densite pour avoir un polymere avec des caracteristiques specifiques. La conductivite thermique a ete ensuite mesuree suivant la norme ASTM E1530. L'echantillon realise avec la deuxieme methode avec une proportion de bentonite pour 5 proportions de saccharose (M2 B1 : S5) signale la possibilite de produire des materiaux de graphene a partir de ressources naturelles. La surface specifique a considerablement augmente de (75,88 m2/g) pour bentonite non traiter a (139,76 m2/g) pour l'echantillon (M2 B1 : S5). Une augmentation significative de la conductivite par pression (95,3 S/m sous une pression de 6,5 MPa par rapport a 1,45*10 -3 S/m pour la bentonite) et la conductivite thermique dans le polyethylene basse densite a une concentration de 10% d'additif (0,332 W/m.K a 0,279 W/m.K) ont ete observes pour le meme echantillon M2 B1 : S5 comparativement a la bentonite non traitee. Les applications possibles sont par exemple les senseurs et les actuateurs par pression.

Steam--water mixing and system hydrodynamics program. Task 4. Quarterly progress report, October 1, 1977--December 31, 1977. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carbiener, W.A.; Cudnik, R.A.; Dykhuizen, R.C.

Experimental studies were conducted in a /sup 2///sub 15/-scale model of a four-loop pressurized water reactor at pressures to 75 psia to extend the understanding of steam-water interaction phenomena and processes associated with a loss-of-coolant accident. Plenum filling studies were conducted with hydraulic communication between the cold leg and core steam supplies and hot walls, with both fixed and ramped steam flows. Comparisons of correlational fits have been made for penetration data obtained with hydraulic communication, fixed cold leg steam, and no cold leg steam. Statistical tests applied to these correlational fits have indicated that the hydraulic communication and fixedmore » cold leg steam data can be considered to be a common data set. Comparing either of these data sets to the no cold leg steam data using the statistical test indicated that it was unlikely that these sets could be considered to be a common data set. The introduction of cold leg steam results in a slight decrease in penetration relative to that obtained without cold leg steam at the same value of subcooling of water entering the downcomer. A dimensionless parameter which is a weighted mean of a modified Froude number and the Weber number has been proposed as a scaling parameter for penetration data. This parameter contains an additional degree of freedom which allows data from different scales to collapse more closely to a single curve than current scaling parameters permit.« less

RELAP5 Analyses of OECD/NEA ROSA-2 Project Experiments on Intermediate-Break LOCAs at Hot Leg or Cold Leg

NASA Astrophysics Data System (ADS)

Takeda, Takeshi; Maruyama, Yu; Watanabe, Tadashi; Nakamura, Hideo

Experiments simulating PWR intermediate-break loss-of-coolant accidents (IBLOCAs) with 17% break at hot leg or cold leg were conducted in OECD/NEA ROSA-2 Project using the Large Scale Test Facility (LSTF). In the hot leg IBLOCA test, core uncovery started simultaneously with liquid level drop in crossover leg downflow-side before loop seal clearing (LSC) induced by steam condensation on accumulator coolant injected into cold leg. Water remained on upper core plate in upper plenum due to counter-current flow limiting (CCFL) because of significant upward steam flow from the core. In the cold leg IBLOCA test, core dryout took place due to rapid liquid level drop in the core before LSC. Liquid was accumulated in upper plenum, steam generator (SG) U-tube upflow-side and SG inlet plenum before the LSC due to CCFL by high velocity vapor flow, causing enhanced decrease in the core liquid level. The RELAP5/MOD3.2.1.2 post-test analyses of the two LSTF experiments were performed employing critical flow model in the code with a discharge coefficient of 1.0. In the hot leg IBLOCA case, cladding surface temperature of simulated fuel rods was underpredicted due to overprediction of core liquid level after the core uncovery. In the cold leg IBLOCA case, the cladding surface temperature was underpredicted too due to later core uncovery than in the experiment. These may suggest that the code has remaining problems in proper prediction of primary coolant distribution.

Effect of variation of impression material combinations, dual arch tray types, and sequence of pour on the accuracy of working dies: "An in vitro study".

PubMed

Reddy, Nagam Raja; Reddy, Jakranpally Sathya; Padmaja, Bramha Josyula Indira; Reddy, Budigi Madan Mohan; Sunil, Motupalli; Reddy, Bommireddy Tejeswar

2016-01-01

To evaluate the accuracy of dies made from dual arch impressions using different sectional dual arch trays, combinations of elastomeric impression materials, and the sequence of pour of dies. The dual arch impression materials were grouped into three groups depending on the combination of impression materials used and each group is subdivided into four subgroups. A sample size of 8 in each subgroup yielding a total 96 impressions will be made into three groups of 32 each (Group I, II, and III). Group I constitute impressions made using monophase (M) impression material, Group II constitute impressions made using combination of heavy body and light body (HL), and Group III constitute impressions made using combination of putty and light body (PL). Dies obtained were evaluated with a travelling microscope to measure the buccolingual width of the tooth at the margin by using the sharp corners of the notches as reference points. Descriptive analysis namely mean and standard deviation, one-way analysis of variance test. The results obtained in this study indicate that though not statistically significant, the metal dual arch trays performed better when compared to the plastic trays in reproducing die dimensions. From the results obtained, dies poured from combination of heavy body and light body impressions using plastic or metal dual arch trays showed least variation in bucco-lingual dimension from master model.

Effect of variation of impression material combinations, dual arch tray types, and sequence of pour on the accuracy of working dies: “An in vitro study”

PubMed Central

Reddy, Nagam Raja; Reddy, Jakranpally Sathya; Padmaja, Bramha Josyula Indira; Reddy, Budigi Madan Mohan; Sunil, Motupalli; Reddy, Bommireddy Tejeswar

2016-01-01

Aims: To evaluate the accuracy of dies made from dual arch impressions using different sectional dual arch trays, combinations of elastomeric impression materials, and the sequence of pour of dies. Subjects and Methods: The dual arch impression materials were grouped into three groups depending on the combination of impression materials used and each group is subdivided into four subgroups. A sample size of 8 in each subgroup yielding a total 96 impressions will be made into three groups of 32 each (Group I, II, and III). Group I constitute impressions made using monophase (M) impression material, Group II constitute impressions made using combination of heavy body and light body (HL), and Group III constitute impressions made using combination of putty and light body (PL). Dies obtained were evaluated with a travelling microscope to measure the buccolingual width of the tooth at the margin by using the sharp corners of the notches as reference points. Statistical Analysis Used: Descriptive analysis namely mean and standard deviation, one-way analysis of variance test. Results: The results obtained in this study indicate that though not statistically significant, the metal dual arch trays performed better when compared to the plastic trays in reproducing die dimensions. Conclusions: From the results obtained, dies poured from combination of heavy body and light body impressions using plastic or metal dual arch trays showed least variation in bucco-lingual dimension from master model. PMID:27141172

Three-stage linear, split-Stirling cryocooler for 1 to 2K magnetic cold stage

NASA Technical Reports Server (NTRS)

Longsworth, R. C.

1993-01-01

A long-life, linear, high efficiency 8K split Stirling cycle cryocooler was designed, built, and tested. The refrigerator is designed for cooling a 50 mW, 1.5K magnetic cold stage. Dual opposed piston compressors are driven by moving-coil linear motors. The three stage expander, although not completed, is also driven by a linear motor and is designed to produce 1 SW at 60K, 4W at 16K, and 1.2W at 8K. The cold regenerator employs a parallel gap construction for high efficiency. The key technology areas addressed include warm and cold flexible suspension bearings and a new cold regenerator geometry for high efficiency at 8K.

Use of Steel Fiber-Reinforced Rubberized Concrete in Cold Regions

DOT National Transportation Integrated Search

2017-12-24

This report documents and presents the use of steel fiber-reinforced rubberized concrete (SFRRC) in cold regions. Further investigation of SFRRC use was conducted with the wheel tracker rut and freeze-thaw laboratory testing procedures at the Univers...

42. Casting floor, "B" furnace, pour in progress; mudgun is ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. Casting floor, "B" furnace, pour in progress; mudgun is to right of furnace; operator takes temperature of iron in trough during pout. Looking south - Rouge Steel Company, 3001 Miller Road, Dearborn, MI

INTERIOR VIEW WITH LADLE POURING MOLTEN IRON INTO QBOP FURNACE. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW WITH LADLE POURING MOLTEN IRON INTO Q-BOP FURNACE. - U.S. Steel, Fairfield Works, Q-Bop Furnace, North of Valley Road & West of Ensley, Pleasant Grove Road, Fairfield, Jefferson County, AL

3D joystick for robotic arm control by individuals with high level spinal cord injuries.

PubMed

Jiang, Hairong; Wachs, Juan P; Pendergast, Martin; Duerstock, Bradley S

2013-06-01

An innovative 3D joystick was developed to enable quadriplegics due to spinal cord injuries (SCIs) to more independently and efficiently operate a robotic arm as an assistive device. The 3D joystick was compared to two different manual input modalities, a keyboard control and a traditional joystick, in performing experimental robotic arm tasks by both subjects without disabilities and those with upper extremity mobility impairments. Fitts's Law targeting and practical pouring tests were conducted to compare the performance and accuracy of the proposed 3D joystick. The Fitts's law measurements showed that the 3D joystick had the best index of performance (IP), though it required an equivalent number of operations and errors as the standard robotic arm joystick. The pouring task demonstrated that the 3D joystick took significantly less task completion time and was more accurate than keyboard control. The 3D joystick also showed a decreased learning curve to the other modalities.

Arctic Planning Scenarios: Scenario #1: Defence Scenario

DTIC Science & Technology

2011-07-01

scénarios pour la planification future et d’aider les commandements opérationnels dans leur interaction avec les autres centres d’opérations. Ce rapport...scénarios pour la planification future. Ce rapport présente l’un des scénarios, qui est axé sur une intervention centrée sur la défense. Résultats : Le...et d’autres personnes qui participent à la planification de la défense du Canada auront besoin d’un jeu complet de scénarios pour évaluer les

2010 Coalition Battle Management Language Workshop (Atelier 2010 sur le langage de gestion du champ de bataille pour les operations en coalition)

DTIC Science & Technology

2010-02-01

Feb 2010 2010 Coalition Battle Management Language Workshop (Atelier 2010 sur le langage de gestion du champ de bataille pour les opérations en...RTO MEETING PROCEEDINGS MP-MSG-079 2010 Coalition Battle Management Language Workshop (Atelier 2010 sur le langage de gestion du champ de ...RTO-MP-MSG-079 ES - 3 Atelier 2010 sur le langage de gestion du champ de bataille pour les opérations en coalition (RTO-MP-MSG-079

Acute nonhypothermic exposure to cold impedes motor skill performance in video gaming compared to thermo-neutral and hot conditions.

PubMed

Edwards, Andrew M; Crowther, Robert G; Morton, R Hugh; Polman, Remco C

2011-02-01

The study examined whether or not acute exposure to unfamiliar hot or cold conditions impairs performance of highly skilled coordinative activities and whether prior physical self-efficacy beliefs were associated with task completion. Nineteen volunteers completed both Guitar Hero and Archery activities as a test battery using the Nintendo Wii console in cold (2 degrees C), neutral (20 degrees C), and hot (38 degrees C) conditions. Participants all completed physical self-efficacy questionnaires following experimental familiarization. Performances of both Guitar Hero and Archery significantly decreased in the cold compared with the neutral condition. The cold trial was also perceived as the condition requiring both greater concentration and effort. There was no association between performance and physical self-efficacy. Performance of these coordinative tasks was compromised by acute (nonhypothermic) exposure to cold; the most likely explanation is that the cold condition presented a greater challenge to attentional processes as a form of environmental distraction.

Report of cold agglutinins in a patient with acute ischemic stroke.

PubMed

Jin, Haiqiang; Sun, Wei; Sun, Yongan; Huang, Yining; Sun, Yunchuang

2015-10-30

Studies on the role of cold agglutinins in the pathogenesis of acute ischemic stroke are scarce. We present a case of an elderly man with acute cerebral infarction probably due to cold agglutinin disease. On a cold morning, a 71-year-old male of Han nationality with a complaint of sudden onset left-sided weakness and difficulty in speaking was brought to the emergency department. Diffusion weighted magnetic resonance imaging of the brain showed a high-intensity area in the right basal ganglia and corona radiata. Laboratory test showed the presence of high titers of cold agglutinins. There was no history of common risk factors of atherosclerosis, such as hypertension, diabetes mellitus, coronary artery disease or smoking. After being exposed to warm temperature, and with corticosteroid therapy and blood transfusion, the patient's symptoms relieved rapidly. We report here the first case of cerebral infarction probably due to the cold agglutinin disease. The underlying mechanism of cold agglutinins in the pathogenesis of acute ischemic stroke needs to be investigated further.

Effect of cold conditions on manual performance while wearing petroleum industry protective clothing.

PubMed

Wiggen, Øystein Nordrum; Heen, Sigri; Færevik, Hilde; Reinertsen, Randi Eidsmo

2011-01-01

The purpose of this study was to investigate manual performance and thermal responses during low work intensity in persons wearing standard protective clothing in the petroleum industry when they were exposed to a range of temperatures (5, -5, -15 and -25℃) that are relevant to environmental conditions for petroleum industry personnel in northern regions. Twelve men participated in the study. Protective clothing was adjusted for the given cold exposure according to current practices. The subjects performed manual tests five times under each environmental condition. The manual performance test battery consisted of four different tests: tactile sensation (Semmes-Weinstein monofilaments), finger dexterity (Purdue Pegboard), hand dexterity (Complete Minnesota dexterity test) and grip strength (grip dynamometer). We found that exposure to -5℃ or colder lowered skin and body temperatures and reduced manual performance during low work intensity. In conclusion the current protective clothing at a given cold exposure is not adequate to maintain manual performance and thermal balance for petroleum workers in the high north.

Modelisation de photodetecteurs a base de matrices de diodes avalanche monophotoniques pour tomographie d'emission par positrons

NASA Astrophysics Data System (ADS)

Corbeil Therrien, Audrey

La tomographie d'emission par positrons (TEP) est un outil precieux en recherche preclinique et pour le diagnostic medical. Cette technique permet d'obtenir une image quantitative de fonctions metaboliques specifiques par la detection de photons d'annihilation. La detection des ces photons se fait a l'aide de deux composantes. D'abord, un scintillateur convertit l'energie du photon 511 keV en photons du spectre visible. Ensuite, un photodetecteur convertit l'energie lumineuse en signal electrique. Recemment, les photodiodes avalanche monophotoniques (PAMP) disposees en matrice suscitent beaucoup d'interet pour la TEP. Ces matrices forment des detecteurs sensibles, robustes, compacts et avec une resolution en temps hors pair. Ces qualites en font un photodetecteur prometteur pour la TEP, mais il faut optimiser les parametres de la matrice et de l'electronique de lecture afin d'atteindre les performances optimales pour la TEP. L'optimisation de la matrice devient rapidement une operation difficile, car les differents parametres interagissent de maniere complexe avec les processus d'avalanche et de generation de bruit. Enfin, l'electronique de lecture pour les matrices de PAMP demeure encore rudimentaire et il serait profitable d'analyser differentes strategies de lecture. Pour repondre a cette question, la solution la plus economique est d'utiliser un simulateur pour converger vers la configuration donnant les meilleures performances. Les travaux de ce memoire presentent le developpement d'un tel simulateur. Celui-ci modelise le comportement d'une matrice de PAMP en se basant sur les equations de physique des semiconducteurs et des modeles probabilistes. Il inclut les trois principales sources de bruit, soit le bruit thermique, les declenchements intempestifs correles et la diaphonie optique. Le simulateur permet aussi de tester et de comparer de nouvelles approches pour l'electronique de lecture plus adaptees a ce type de detecteur. Au final, le simulateur vise a quantifier l'impact des parametres du photodetecteur sur la resolution en energie et la resolution en temps et ainsi optimiser les performances de la matrice de PAMP. Par exemple, l'augmentation du ratio de surface active ameliore les performances, mais seulement jusqu'a un certain point. D'autres phenomenes lies a la surface active, comme le bruit thermique, provoquent une degradation du resultat. Le simulateur nous permet de trouver un compromis entre ces deux extremes. Les simulations avec les parametres initiaux demontrent une efficacite de detection de 16,7 %, une resolution en energie de 14,2 % LMH et une resolution en temps de 0.478 ns LMH. Enfin, le simulateur propose, bien qu'il vise une application en TEP, peut etre adapte pour d'autres applications en modifiant la source de photons et en adaptant les objectifs de performances. Mots-cles : Photodetecteurs, photodiodes avalanche monophotoniques, semiconducteurs, tomographie d'emission par positrons, simulations, modelisation, detection monophotonique, scintillateurs, circuit d'etouffement, SPAD, SiPM, Photodiodes avalanche operees en mode Geiger

Evaluation of selected sidewalk pavement surfaces for vibration experienced by users of manual and powered wheelchairs.

PubMed

Cooper, Rory A; Wolf, Erik; Fitzgerald, Shirley G; Kellerher, Annmarie; Ammer, William; Boninger, Michael L; Cooper, Rosemarie

2004-01-01

Obstacles such as bumps, curb descents, and uneven driving surfaces cause vibrations that affect the wheelchair, and in turn, the wheelchair user. Chronic exposure can cause low-back pain, disk degeneration, and other harmful effects. Little research has been conducted to assess the vibrations experienced by wheelchair users. The purpose of this study was to conduct an evaluation of the vibration exposure during electric-powered wheelchair driving and mechanical energy requirements for manual wheelchair propulsion over selected sidewalk surfaces. The goal was to determine the criteria for a wheelchair-pedestrian access route that does not require excessive propulsive work or expose wheelchair users to potentially harmful vibrations. Ten unimpaired individuals participated in this study. Six sidewalk surfaces were tested. Measured variables included power of the acceleration per octave, mechanical work to propel over surfaces, peak acceleration, and frequency at which peak acceleration occurs. For both the manual and electric-powered wheelchair, at 1 m/s, significant differences were found in peak accelerations between the seat and footrest (P < 0.0001) and between the sidewalk surfaces (P = 0.004). The greatest risk for injury caused by shock and vibration exposure occurs at frequencies near the natural frequency of seated humans (4-15 Hz). The values for work required to propel over the surfaces tested were not statistically significantly different. Besides appearance and construction, the only distinguishing characteristic was surface roughness caused by the joints. When treating the poured concrete sidewalk as the standard, surfaces 2, 3, 5, and 6 compared most favorably in terms of vibration exposure, whereas surface 4 produced mixed results. Surfaces 2, 3, 5, and 6 yielded results that were similar to the poured concrete sidewalk and could be considered acceptable for wheelchair users. In conclusion, surfaces other than the traditional poured concrete can be used for pedestrian access routes without adding vibration exposure or reducing propulsion efficiency.

Advantages and limitations for users of double pit pour-flush latrines: a qualitative study in rural Bangladesh.

PubMed

Hussain, Faruqe; Clasen, Thomas; Akter, Shahinoor; Bawel, Victoria; Luby, Stephen P; Leontsini, Elli; Unicomb, Leanne; Barua, Milan Kanti; Thomas, Brittany; Winch, Peter J

2017-05-25

In rural Bangladesh, India and elsewhere, pour-flush pit latrines are the most common sanitation system. When a single pit latrine becomes full, users must empty it themselves and risk exposure to fresh feces, pay an emptying service to remove pit contents or build a new latrine. Double pit pour-flush latrines may serve as a long-term sanitation option including high water table areas because the pits do not need to be emptied immediately and the excreta decomposes into reusable soil. Double pit pour-flush latrines were implemented in rural Bangladesh for 'hardcore poor' households by a national NGO, BRAC. We conducted interviews, focus groups, and spot checks in two low-income, rural areas of Bangladesh to explore the advantages and limitations of using double pit latrines compared to single pit latrines. The rural households accepted the double pit pour-flush latrine model and considered it feasible to use and maintain. This latrine design increased accessibility of a sanitation facility for these low-income residents and provided privacy, convenience and comfort, compared to open defecation. Although a double pit latrine is more costly and requires more space than a single pit latrine the households perceived this sanitation system to save resources, because households did not need to hire service workers to empty pits or remove decomposed contents themselves. In addition, the excreta decomposition process produced a reusable soil product that some households used in homestead gardening. The durability of the latrine superstructures was a problem, as most of the bamboo-pole superstructure broke after 6-18 months of use. Double pit pour-flush latrines are a long-term improved sanitation option that offers users several important advantages over single pit pour-flush latrines like in rural Bangladesh which can also be used in areas with high water table. Further research can provide an understanding of the comparative health impacts and effectiveness of the model in preventing human excreta from entering the environment.

Dimensions rénales en Service de Néphrologie Clinique, Befelatanana, Antananarivo

PubMed Central

Ramilitiana, Benja; Dodo, Mihary; Rakotoarimanga, Henintsoa Nirina; Randriamboavonjy, Rado Lalao; Randriamarotia, Willy Franck

2016-01-01

La connaissance des dimensions rénales pour tout individu et pour toute ethnie, aide à une décision médicale d'ordre diagnostique et thérapeutique. Pour un pays à faible revenu comme Madagascar, l’échographie constitue un outil idéal à cette fin. Ce travail a comme objectifs de recueillir les dimensions rénales, puis de chercher la corrélation entre ces dernières et les paramètres démographiques ou anthropométriques des Malgaches. Il s'agit d'une étude rétrospective, s’étalant sur une période de 3 ans, effectuée dans le service de Néphrologie du centre hospitalier de Befelatanana, Antananarivo, recrutant 200 patients non diabétiques, sans maladie rénale chronique. L’âge moyen de nos patients était de 45 ans ±16, avec un sex ratio de 0,9. En moyenne, les dimensions (longueur × largeur × épaisseur) étaient de 98 mm × 42 mm × 30 mm pour le rein droit et 99 mm × 45 mm × 31 mm pour le rein gauche. Nous avons retrouvé une différence significative entre le rein droit et gauche sur la longueur (p<0,00001) et la largeur (p = 0,03). Une relation significative était aussi retrouvée entre la longueur rénale et l’âge (p = 0,0016 et p = 0,04 respectivement pour le rein droit et le rein gauche). Aucune relation significative n'a été établie entre les dimensions rénales et la taille ni le poids de nos patients. Malgré ses limites, notre étude apporterait une aide sur le plan pratique clinique ainsi que pour une étude ultérieure. PMID:27642455

Scanning Webb’s Surrogate Eye

NASA Image and Video Library

2017-12-08

Engineer Erin Wilson adds aluminum tape to electrical cables to protect them from the cold during environmental testing of special optical equipment. These tests will verify the alignment of the actual flight instruments that will fly aboard NASA’s James Webb Space Telescope. "Because the flight science instruments detect infrared light, they must be extremely cold to work, and so the environment we test them in must be extremely cold too," Wilson says. Wilson is working in the Space Environment Simulator thermal-vacuum chamber at NASA's Goddard Space Flight Center in Greenbelt, Md. The subject of the testing is the Optical Telescope Element (OTE) Simulator, or OSIM. The hardware seen in the background is the Beam Image Analyzer, which will be used to measure OSIM. It sits above the OSIM, which is under the platform that Wilson is working on. The OSIM is about two stories tall and almost as wide as the whole test chamber. The job of the OSIM is to generate a beam of light just like the one that the real telescope optics will feed into the actual flight science instruments. Because the real flight science instruments will be used to test the real flight telescope, their alignment and performance have to be verified first, using OSIM, and before that can happen, the OSIM has to tested and verified. In space, the telescope optics act as Webb’s eye, and on the ground, the OSIM substitutes for the telescope optics, says Robert Rashford, manager for the OSIM as well as the Integrated Science Instrument Module (ISIM) Electronics Compartment. This hardware is being tested in an environment that mimics the hard vacuum and cold temperatures that Webb will experience in space. After Erin and others were done setting things up in the test chamber, Goddard engineers sealed it up, evacuated all the air and lowered the temperature of the equipment being tested to 42 Kelvin (-384-point-1 Fahrenheit or -231-point-1 Celsius). "It has taken a little over a month to get temperatures cold enough to duplicate the temperatures that Webb will see in operation in space," Rashford says. In the next couple weeks Rashford and the team of Goddard engineers will measure the OSIM with the Beam Image Analyzer. This extremely cold or “cryogenic” optical testing and verification process will likely take 90 days to complete. Laura Betz NASA's Goddard Space Flight Center, Greenbelt, Md. NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Evaluation of two cold thermoregulatory models for prediction of core temperature during exercise in cold water.

PubMed

Castellani, John W; O'Brien, Catherine; Tikuisis, Peter; Sils, Ingrid V; Xu, Xiaojiang

2007-12-01

Cold thermoregulatory models (CTM) have primarily been developed to predict core temperature (T(core)) responses during sedentary immersion. Few studies have examined their efficacy to predict T(core) during exercise cold exposure. The purpose of this study was to compare observed T(core) responses during exercise in cold water with the predicted T(core) from a three-cylinder (3-CTM) and a six-cylinder (6-CTM) model, adjusted to include heat production from exercise. A matrix of two metabolic rates (0.44 and 0.88 m/s walking), two water temperatures (10 and 15 degrees C), and two immersion depths (chest and waist) were used to elicit different rates of T(core) changes. Root mean square deviation (RMSD) and nonparametric Bland-Altman tests were used to test for acceptable model predictions. Using the RMSD criterion, the 3-CTM did not fit the observed data in any trial, whereas the 6-CTM fit the data (RMSD less than standard deviation) in four of eight trials. In general, the 3-CTM predicted a rapid decline in core temperature followed by a plateau. For the 6-CTM, the predicted T(core) appeared relatively tight during the early part of immersion, but was much lower during the latter portions of immersion, accounting for the nonagreement between RMSD and SD values. The 6-CTM was rerun with no adjustment for exercise metabolism, and core temperature and heat loss predictions were tighter. In summary, this study demonstrated that both thermoregulatory models designed for sedentary cold exposure, currently, cannot be extended for use during partial immersion exercise in cold water. Algorithms need to be developed to better predict heat loss during exercise in cold water.

The CGM of Massive Galaxies: Where Cold Gas Goes to Die?

NASA Astrophysics Data System (ADS)

Howk, Jay

2017-08-01

We propose to survey the cold HI content and metallicity of the circumgalactic medium (CGM) around 50 (45 new, 5 archival) z 0.5 Luminous Red Galaxies (LRGs) to directly test a fundamental prediction of galaxy assembly models: that cold, metal-poor accretion does not survive to the inner halos of very massive galaxies. Accretion and feedback through the CGM play key roles in our models of the star formation dichotomy in galaxies. Low mass galaxies are thought to accrete gas in cold streams, while high mass galaxies host hot, dense halos that heat incoming gas and prevent its cooling, thereby quenching star formation. HST/COS has provided evidence for cold, metal-poor streams in the halos of star-forming galaxies (consistent with cold accretion). Observations have also demonstrated the presence of cool gas in the halos of passive galaxies, a potential challenge to the cold/hot accretion model. Our proposed observations will target the most massive galaxies and address the origin of the cool CGM gas by measuring the metallicity. This experiment is enabled by our novel approach to deriving metallicities, allowing the use of much fainter QSOs. It cannot be done with archival data, as these rare systems are not often probed along random sight lines. The H I column density (and metallicity) measurements require access to the UV. The large size of our survey is crucial to robustly assess whether the CGM in these galaxies is unique from that of star-forming systems, a comparison that provides the most stringent test of cold-mode accretion/quenching models to date. Conversely, widespread detections of metal-poor gas in these halos will seriously challenge the prevailing theory.

POURING IRON FROM ELECTRIC FURNACE INTO BULL LADLE AFTER MAGNESIUM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

POURING IRON FROM ELECTRIC FURNACE INTO BULL LADLE AFTER MAGNESIUM HAD BEEN ADDED TO GENERATE DUCTILE IRON WHEN IT COOLS IN THE MOLD. - Southern Ductile Casting Company, Casting, 2217 Carolina Avenue, Bessemer, Jefferson County, AL

6. VIEW LOOKING WEST FROM THE POURING AISLE OF THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW LOOKING WEST FROM THE POURING AISLE OF THE ELECTRIC FURNACE BUILDING AT ELECTRIC FURNACE X-3. - U.S. Steel Duquesne Works, Electric Furnace Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Miroirs multicouches C/SI a incidence normale pour la region spectrale 25-40 nanometres

NASA Astrophysics Data System (ADS)

Grigonis, Marius

Nous avons propose la nouvelle combinaison de materiaux, C/Si, pour la fabrication de miroirs multicouches a incidence normale dans la region spectrale 25-40 nm. Les resultats experimentaux montrent que cette combinaison possede une reflectivite d'environ ~25% dans la region spectrale 25-33 nm et une reflectivite d'environ ~23% dans la region spectrale 33-40 nm. Ces valeurs de reflectivite sont les plus grandes obtenues jusqu'a maintenant dans la region spectrale 25-40 nm. Les miroirs multicouches ont ete par la suite caracterises par microscopie electronique a transmission, par diverses techniques de diffraction des rayons X et par spectroscopies d'electrons AES et ESCA. La resistance des miroirs aux temperatures elevees a ete egalement etudiee. Les resultats fournis par les methodes de caracterisation indiquent que cette combinaison possede des caracteristiques tres prometteuses pour son application comme miroir pour les rayons X mous.

Analysis of Fatigue Crack Paths in Cold Drawn Pearlitic Steel

PubMed Central

Toribio, Jesús; González, Beatriz; Matos, Juan-Carlos

2015-01-01

In this paper, a fracto-metallographic analysis was performed on the cracked specimens of cold drawn pearlitic steel subjected to fatigue tests. Fatigue cracks are transcollonial and exhibit a preference for fracturing pearlitic lamellae, with non-uniform crack opening displacement values, micro-discontinuities, branchings, bifurcations and frequent local deflections that create microstructural roughness. At the micro-level, the cold drawn pearlitic steel exhibits higher micro-roughness than the hot rolled bar (this is a consequence of the manufacturing process by cold drawing), so that the actual fractured surface in the cold drawn wire is greater than that in the hot rolled bar, due to the fact that the crack deflection events are more frequent and with higher angle in the former (the heavily drawn prestressing steel wire). These findings show the relevant role on the manufacturing process by cold drawing in the fatigue crack propagation in pearlitic steel. PMID:28793647

Analysis of Fatigue Crack Paths in Cold Drawn Pearlitic Steel.

PubMed

Toribio, Jesús; González, Beatriz; Matos, Juan-Carlos

2015-11-04

In this paper, a fracto-metallographic analysis was performed on the cracked specimens of cold drawn pearlitic steel subjected to fatigue tests. Fatigue cracks are transcollonial and exhibit a preference for fracturing pearlitic lamellae, with non-uniform crack opening displacement values, micro-discontinuities, branchings, bifurcations and frequent local deflections that create microstructural roughness. At the micro-level, the cold drawn pearlitic steel exhibits higher micro-roughness than the hot rolled bar (this is a consequence of the manufacturing process by cold drawing), so that the actual fractured surface in the cold drawn wire is greater than that in the hot rolled bar, due to the fact that the crack deflection events are more frequent and with higher angle in the former (the heavily drawn prestressing steel wire). These findings show the relevant role on the manufacturing process by cold drawing in the fatigue crack propagation in pearlitic steel.

Genetic and epigenetic stability of cryopreserved and cold-stored hops (Humulus lupulus L.).

PubMed

Peredo, Elena L; Arroyo-García, Rosa; Reed, Barbara M; Revilla, M Angeles

2008-12-01

Conventional cold storage and cryopreservation methods for hops (Humulus lupulus L.) are available but, to our knowledge, the genetic and epigenetic stability of the recovered plants have not been tested. This study analyzed 51 accessions of hop using the molecular techniques, Random Amplified DNA Polymorphism (RAPD) and Amplified Fragment Length Polymorphism (AFLP), revealing no genetic variation among greenhouse-grown controls and cold stored or cryopreserved plants. Epigenetic stability was evaluated using Methylation Sensitive Amplified Polymorphism (MSAP). Over 36% of the loci were polymorphic when the cold and cryo-treated plants were compared to greenhouse plants. The main changes were demethylation events and they were common to the cryopreserved and cold stored plants indicating the possible effect of the in vitro establishment process, an essential step in both protocols. Protocol-specific methylation patterns were also detected indicating that both methods produced epigenetic changes in plants following cold storage and cryopreservation.

Reliability of the method of levels for determining cutaneous temperature sensitivity

NASA Astrophysics Data System (ADS)

Jakovljević, Miroljub; Mekjavić, Igor B.

2012-09-01

Determination of the thermal thresholds is used clinically for evaluation of peripheral nervous system function. The aim of this study was to evaluate reliability of the method of levels performed with a new, low cost device for determining cutaneous temperature sensitivity. Nineteen male subjects were included in the study. Thermal thresholds were tested on the right side at the volar surface of mid-forearm, lateral surface of mid-upper arm and front area of mid-thigh. Thermal testing was carried out by the method of levels with an initial temperature step of 2°C. Variability of thermal thresholds was expressed by means of the ratio between the second and the first testing, coefficient of variation (CV), coefficient of repeatability (CR), intraclass correlation coefficient (ICC), mean difference between sessions (S1-S2diff), standard error of measurement (SEM) and minimally detectable change (MDC). There were no statistically significant changes between sessions for warm or cold thresholds, or between warm and cold thresholds. Within-subject CVs were acceptable. The CR estimates for warm thresholds ranged from 0.74°C to 1.06°C and from 0.67°C to 1.07°C for cold thresholds. The ICC values for intra-rater reliability ranged from 0.41 to 0.72 for warm thresholds and from 0.67 to 0.84 for cold thresholds. S1-S2diff ranged from -0.15°C to 0.07°C for warm thresholds, and from -0.08°C to 0.07°C for cold thresholds. SEM ranged from 0.26°C to 0.38°C for warm thresholds, and from 0.23°C to 0.38°C for cold thresholds. Estimated MDC values were between 0.60°C and 0.88°C for warm thresholds, and 0.53°C and 0.88°C for cold thresholds. The method of levels for determining cutaneous temperature sensitivity has acceptable reliability.

An empirical model for optimal highway durability in cold regions.

DOT National Transportation Integrated Search

2016-03-10

We develop an empirical tool to estimate optimal highway durability in cold regions. To test the model, we assemble a data set : containing all highway construction and maintenance projects in Arizona and Washington State from 1990 to 2014. The data ...

Durability and smart condition assessment of ultra-high performance concrete in cold climates.

DOT National Transportation Integrated Search

2016-12-31

The goals of this study were to develop ecological ultra-high performance concrete (UHPC) with local materials and supplementary cementitious materials and to evaluate the long-term performance of UHPC in cold climates using effective mechanical test...

The Harvard Fatigue Laboratory: contributions to World War II.

PubMed

Folk, G Edgar

2010-09-01

The war contributions of the Harvard Fatigue Laboratory in Cambridge, MA, were recorded in 169 Technical Reports, most of which were sent to the Office of the Quartermaster General. Earlier reports were sent to the National Research Council and the Office of Scientific Research and Development. Many of the reports from 1941 and later dealt with either physical fitness of soldiers or the energetic cost of military tasks in extreme heat and cold. New military emergency rations to be manufactured in large quantities were analyzed in the Fatigue Laboratory and then tested in the field. Newly designed cold weather clothing was tested in the cold chamber at -40 degrees F, and desired improvements were made and tested in the field by staff and soldiers in tents and sleeping bags. Electrically heated clothing was designed for high-altitude flight crews and tested both in laboratory chambers and field tests before being issued. This eye witness account of the Harvard Fatigue Laboratory during World War II was recorded by Dr. G. Edgar Folk, who is likely the sole surviving member of that famous laboratory.

2015 Annual Reuse Report for the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Ponds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, Michael George

This report describes conditions and information, as required by the state of Idaho, Department of Environmental Quality Reuse Permit I-161-02, for the Advanced Test Reactor Complex Cold Waste Ponds located at Idaho National Laboratory from November 1, 2014–October 31, 2015. The effective date of Reuse Permit I-161-02 is November 20, 2014 with an expiration date of November 19, 2019.

Estimating and projecting the effect of cold waves on mortality in 209 US cities.

PubMed

Wang, Yan; Shi, Liuhua; Zanobetti, Antonella; Schwartz, Joel D

2016-09-01

The frequency, duration, and intensity of cold waves are expected to decrease in the near future under the changing climate. However, there is a lack of understanding on future mortality related to cold waves. The present study conducted a large-scale national projection to estimate future mortality attributable to cold waves during 1960-2050 in 209 US cities. Cold waves were defined as two, three, or at least four consecutive days with daily temperature lower than the 5th percentile of temperatures in each city. The lingering period of a cold wave was defined as the non-cold wave days within seven days following that cold wave period. First, with 168million residents in 209 US cities during 1962-2006, we fitted over-dispersed Poisson regressions to estimate the immediate and lingering effects of cold waves on mortality and tested if the associations were modified by the duration of cold waves, the intensity of cold waves, and mean winter temperature (MWT). Then we projected future mortality related to cold waves using 20 downscaled climate models. Here we show that the cold waves (both immediate and lingering) were associated with an increased but small risk of mortality. The associations varied substantially across climate regions. The risk increased with the duration and intensity of cold waves but decreased with MWT. The projected mortality related to cold waves would decrease from 1960 to 2050. Such a decrease, however, is small and may not be able to offset the potential increase in heat-related deaths if the adaptation to heat is not adequate. Copyright © 2016 Elsevier Ltd. All rights reserved.

A novel method for delivering ramped cooling reveals rat behaviours at innocuous and noxious temperatures: A comparative study of human psychophysics and rat behaviour.

PubMed

Dunham, James P; Hulse, Richard P; Donaldson, Lucy F

2015-07-15

Thermal sensory testing in rodents informs human pain research. There are important differences in the methodology for delivering thermal stimuli to humans and rodents. This is particularly true in cold pain research. These differences confound extrapolation and de-value nociceptive tests in rodents. We investigated cooling-induced behaviours in rats and psychophysical thresholds in humans using ramped cooling stimulation protocols. A Peltier device mounted upon force transducers simultaneously applied a ramped cooling stimulus whilst measuring contact with rat hind paw or human finger pad. Rat withdrawals and human detection, discomfort and pain thresholds were measured. Ramped cooling of a rat hind paw revealed two distinct responses: Brief paw removal followed by paw replacement, usually with more weight borne than prior to the removal (temperature inter-quartile range: 19.1 °C to 2.8 °C). Full withdrawal was evoked at colder temperatures (inter quartile range: -11.3 °C to -11.8 °C). The profile of human cool detection threshold and cold pain threshold were remarkably similar to that of the rat withdrawals behaviours. Previous rat cold evoked behaviours utilise static temperature stimuli. By utilising ramped cold stimuli this novel methodology better reflects thermal testing in patients. Brief paw removal in the rat is driven by non-nociceptive afferents, as is the perception of cooling in humans. This is in contrast to the nociceptor-driven withdrawal from colder temperatures. These findings have important implications for the interpretation of data generated in older cold pain models and consequently our understanding of cold perception and pain. Copyright © 2015. Published by Elsevier B.V.

Pourable Foam Insulation

NASA Technical Reports Server (NTRS)

Harvey, James A.; Butler, John M.; Chartoff, Richard P.

1989-01-01

Report describes search for polyisocyanurate/polyurethane foam insulation with superior characteristics. Discusses chemistry of current formulations. Tests of formulations, of individual ingredients and or alternative new formulations described. Search revealed commercially available formulations exhibiting increased thermal stability at temperatures up to 600 degree C, pours readily before curing, presents good appearance after curing, and remains securely bonded to aluminum at cryogenic temperatures. Total of 42 different formulations investigated, 10 found to meet requirements.

Northrop Grumman HEC flight coaxial cryocoolers performance

NASA Astrophysics Data System (ADS)

Nguyen, T.; Russo, J.; Basel, G.; Chi, D.; Abelson, L.

2018-05-01

The Northrop Grumman Aerospace Systems (NGAS) has expanded the cryocooler product line to include a single stage High Efficiency Cryocooler (HEC) cooler with a coaxial pulse tube cold head that operates at temperatures down to 45K. The HEC coaxial pulse tube cooler has been adopted by several customers, and has completed acceptance testing to meet program flight requirements. The NGAS TRL 9 HEC is a pulse tube cryocooler with a flexure bearing compressor which has been delivered for a number of flight payloads that are currently operating in space. To date, NGAS has delivered space cryocoolers in several configurations including single stage with a linear cold head and two stage with both linear and coaxial cold heads. The new HEC coaxial cooler uses the same TRL9 HEC compressor with a passive pulse tube cold head, to maintain the flight heritage of the HEC linear cooler. In this paper, we present the flight acceptance test data of the HEC coaxial cryocooler, which includes thermal performance, launch vibration and thermal cycling. The HEC coaxial cooler has demonstrated excellent performance in family with the flight qualified HEC linear cooler. The HEC coaxial cooler provides users with additional flexibility in selecting the cold head configuration to meet their particular applications.

A cross-species translational pharmacokinetic-pharmacodynamic evaluation of core body temperature reduction by the TRPM8 blocker PF-05105679.

PubMed

Gosset, James R; Beaumont, Kevin; Matsuura, Tomomi; Winchester, Wendy; Attkins, Neil; Glatt, Sophie; Lightbown, Ian; Ulrich, Kristina; Roberts, Sonia; Harris, Jolie; Mesic, Emir; van Steeg, Tamara; Hijdra, Diana; van der Graaf, Piet H

2017-11-15

PF-05105679 is a moderately potent TRPM8 blocker which has been evaluated for the treatment of cold pain sensitivity. The TRPM8 channel is responsible for the sensation of cold environmental temperatures and has been implicated in regulation of core body temperature. Consequently, blockade of TRPM8 has been suggested to result in lowering of core body temperature. As part of the progression to human studies, the effect of PF-05105679 on core body temperature has been investigated in animals. Safety pharmacology studies showed that PF-05105679 reduced core body temperature in a manner that was inversely related to body weight of the species tested (greater exposure to PF-05105679 was required to lower temperature by 1°C in higher species). Based on an allometric (body weight) relationship, it was hypothesized that PF-05105679 would not lower core body temperature in humans at exposures that could exhibit pharmacological effects on cold pain sensation. On administration to humans, PF-05105679 was indeed effective at reversing the cold pain sensation associated with the cold pressor test in the absence of effects on core body temperature. Copyright © 2017 Elsevier B.V. All rights reserved.

2013 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mike Lewis

2014-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (#LA 000161 01, Modification B), for the wastewater land application site at the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond from November 1, 2012–October 31, 2013. The report contains the following information: • Facility and system description • Permit required effluent monitoring data and loading rates • Groundwater monitoring data • Status of compliance activities • Noncompliance issues • Discussion of the facility’s environmental impacts. During the 2013 permit year, approximately 238 million gallons of wastewater was discharged to the Coldmore » Waste Pond. This is well below the maximum annual permit limit of 375 million gallons. As shown by the groundwater sampling data, sulfate and total dissolved solids concentrations are highest near the Cold Waste Pond and decrease rapidly as the distance from the Cold Waste Pond increases. Although concentrations of sulfate and total dissolved solids are elevated near the Cold Waste Pond, both parameters are below the Ground Water Quality Rule Secondary Constituent Standards in the down gradient monitoring wells.« less

Night-shift work increases cold pain perception.

PubMed

Pieh, Christoph; Jank, Robert; Waiß, Christoph; Pfeifer, Christian; Probst, Thomas; Lahmann, Claas; Oberndorfer, Stefan

2018-05-01

Although night-shift work (NSW) is associated with a higher risk for several physical and mental disorders, the impact of NSW on pain perception is still unclear. This study investigates the impact of NSW on cold pain perception considering the impact of mood and sleepiness. Quantitative sensory testing (QST) was performed in healthy night-shift workers. Cold pain threshold as well as tonic cold pain was assessed after one habitual night (T1), after a 12-hour NSW (T2) and after one recovery night (T3). Sleep quality was measured with the Pittsburgh Sleep Quality Index (PSQI) before T1, sleepiness with the Stanford Sleepiness Scale (SSS) and mood with a German short-version of the Profile of Mood States (ASTS) at T1, T2 and T3. Depending on the distribution of the data, ANOVAs or Friedman tests as well as t- or Wilcoxon tests were performed. Nineteen healthy shift-workers (13 females; 29.7 ± 7.5 years old; 8.1 ± 6.6 years in shift work, PSQI: 4.7 ± 2.2) were included. Tonic cold pain showed a significant difference between T1 (48.2 ± 27.5 mm), T2 (61.7 ± 26.6 mm; effect size: Cohen's d=.49; percent change 28%), and T3 (52.1 ± 28.7 mm) on a 0-100 mm Visual Analog Scale (p = 0.007). Cold pain threshold changed from 11.0 ± 7.9 °C (T1) to 14.5 ± 8.8 °C (T2) (p = 0.04), however, an ANOVA comparing T1, T2, and T3 was not significant (p = 0.095). Sleepiness (SSS) and mood (ASTS) changed significantly between T1, T2 and T3 (p-values < 0.01). The change of mood but not of sleepiness correlated with the difference in tonic cold pain from T1 to T2 (R: 0.53; R 2 : 0.29; p = 0.022). NSW increases cold pain perception. The same tonic cold pain stimulus is rated 28% more painful after NSW and normalizes after a recovery night. Increases in cold pain perception due to NSW appear to be more strongly related to changes in mood as compared to changes in sleepiness. Copyright © 2018 Elsevier B.V. All rights reserved.

Effects of cold-treatment and strain-rate on mechanical properties of NbTi/Cu superconducting composite wires.

PubMed

Guan, Mingzhi; Wang, Xingzhe; Zhou, Youhe

2015-01-01

During design and winding of superconducting magnets at room temperature, a pre-tension under different rate is always applied to improve the mechanical stability of the magnets. However, an inconsistency rises for superconductors usually being sensitive to strain and oversized pre-stress which results in degradation of the superconducting composites' critical performance at low temperature. The present study focused on the effects of the cold-treatment and strain-rate of tension deformation on mechanical properties of NbTi/Cu superconducting composite wires. The samples were immersed in a liquid nitrogen (LN2) cryostat for the adiabatic cold-treatment, respectively with 18-hour, 20-hour, 22-hour and 24-hour. A universal testing machine was utilized for tension tests of the NbTi/Cu superconducting composite wires at room temperature; a small-scale extensometer was used to measure strain of samples with variable strain-rate. The strength, elongation at fracture and yield strength of pre-cold-treatment NbTi/Cu composite wires were drawn. It was shown that, the mechanical properties of the superconducting wires are linearly dependent on the holding time of cold-treatment at lower tensile strain-rate, while they exhibit notable nonlinear features at higher strain-rate. The cold-treatment in advance and the strain-rate of pre-tension demonstrate remarkable influences on the mechanical property of the superconducting composite wires.

Pozzolan cement study : final report.

DOT National Transportation Integrated Search

1979-12-01

An experimental section using Type 1P cement concrete was poured on an active construction project in south Louisiana, near Franklin. A comparison in quality was made between this section and the normal Type 1(B) cement concrete poured on the remaind...

Analyse de L'ancrage des Vortex Intergrains pour le Yttrium BARYUM(2) CUIVRE(3) OXYGENE(7) Polycristallin

NASA Astrophysics Data System (ADS)

Fournier, Patrick

Le Modele de l'Etat Critique Generalise (MECG) est utilise pour decrire les proprietes magnetiques et de transport du YBa_2Cu_3O _7 polycristallin. Ce modele empirique permet de relier la densite de courant critique a la densite de lignes de flux penetrant dans la region intergrain. Deux techniques de mesures sont utilisees pour caracteriser nos materiaux. La premiere consiste a mesurer le champ au centre d'un cylindre creux en fonction du champ magnetique applique pour des temperatures comprises entre 20 et 85K. En variant l'epaisseur de la paroi du cylindre creux, il est possible de suivre l'evolution des cycles d'hysteresis et de determiner des champs caracteristiques qui varient en fonction de cette dimension. En utilisant un lissage des resultats experimentaux, nous determinons J _{co}, H_ {o} et n, les parametres du MECG. La forme des cylindres, avec une longueur comparable au diametre externe, entrai ne la presence d'un champ demagnetisant qui peut etre inclus dans le modele theorique. Ceci nous permet d'evaluer la fraction du volume ecrante, f _{g}, ainsi que le facteur demagnetisant N. Nous trouvons que J_{ co}, H_{o} et f_{g} dependent de la temperature, tandis que n et N (pour une epaisseur de paroi fixe) n'en dependent pas. La deuxieme technique consiste a mesurer le courant critique de lames minces en fonction du champ applique pour differentes temperatures. Nous utilisons un montage que nous avons developpe permettant d'effectuer ces mesures en contact direct avec le liquide refrigerant, i.e. dans l'azote liquide. Nous varions la temperature du liquide en variant la pression du gaz au-dessus du bain d'azote. Cette methode nous permet de balayer des temperatures entre 65K et la temperature critique du materiau ({~ }92K). Nous effectuons le lissage des courbes de courant critique en fonction du champ applique encore a l'aide du MECG, pour a nouveau obtenir ses parametres. Pour trois echantillons avec des traitements thermiques differents, les parametres sont differents confirmant que la variation des proprietes macroscopiques de ces supraconducteurs est intimement reliee a la nature des jonctions entre les grains et de la surface des grains. L'oxygenation prolongee retablit les proprietes initiales des echantillons qui se sont degrades durant le recuit des contacts.

Experimental and numerical analysis of web stiffened cold-formed steel channel column with various types of edge stiffener

NASA Astrophysics Data System (ADS)

Manikandan, P.; Balaji, S.; Sukumar, S.; Sivakumar, M.

2017-06-01

This paper presents the strength and behaviour of web stiffened cold formed steel channel column with various types of edge stiffener under axial compression. An accurate finite element model is developed to simulate the tests results of the proposed section. The finite element model is verified by the test results and good correlation is achieved. The failure modes local, distortional, flexural buckling as well as the interaction between these modes is found in this study. The column strength predicted from the parametric study is compared with the nominal strength calculated by using the direct strength method for cold formed steel members. The reliability of this method is evaluated and suitable modification factor is proposed.

The Effects of Metallurgical Factors on PWSCC Crack Growth Rates in TT Alloy 690 in Simulated PWR Primary Water

NASA Astrophysics Data System (ADS)

Yonezawa, Toshio; Watanabe, Masashi; Hashimoto, Atsushi

2015-06-01

Primary water stress corrosion cracking growth rates (PWSCCGRs) in highly cold-worked thermally treated (TT) Alloy 690 have been recently reported as exhibiting significant heat-to-heat variability. Authors hypothesized that these significant differences could be due to the metallurgical characteristics of each heat. In order to confirm this hypothesis, the effect of fundamental metallurgical characteristics on PWSCCGR measurements in cold-worked TT Alloy 690 has been investigated. The following new observations were made in this study: (1) Microcracks and voids were observed in or near eutectic crystals of grain boundary (GB) M23C6 carbides (primary carbides) after cold rolling, but were not observed before cold rolling. These primary carbides with microcracks and voids were observed in both lightly forged and as-cast and cold-rolled TT Alloy 690 (heat A) as well as in a cold-rolled TT Alloy 690 (heat Y) that simulated the chemical composition and carbide banded structure of the material previously tested by Paraventi and Moshier. However, this was not observed in precipitated (secondary) M23C6 GB carbides in heavily forged and cold-rolled TT Alloy 690 heat A and a cold-rolled commercial TT Alloy 690. (2) From microstructural analyses carried out on the various TT Alloy 690 test materials before and after cold rolling, the amount of eutectic crystals (primary carbides and nitrides) M23C6 and TiN depended on the chemical composition. In particular, the amount of M23C6 depended on the fabrication process. Microcracks and voids in or near the M23C6 and TiN precipitates were generated by the cold rolling process. (3) The PWSCCGRs observed in TT Alloy 690 were different for each heat and fabrication process. The PWSCCGR decreased with increasing Vickers hardness of each heat. However, for the same heats and fabrication processes, the PWSCCGR increased with increasing Vickers hardness due to cold work. Thus, the PWSCCGR must be affected not only by hardness (or equivalently the cold working ratio) but also by grain size, microcracks, and voids of primary M23C6 carbides, etc., which in turn depend on chemical composition and the fabrication process.

Patients’ experiences of cold exposure during ambulance care

PubMed Central

2013-01-01

Background Exposure to cold temperatures is often a neglected problem in prehospital care. Cold exposure increase thermal discomfort and, if untreated causes disturbances of vital body functions until ultimately reaching hypothermia. It may also impair cognitive function, increase pain and contribute to fear and an overall sense of dissatisfaction. The aim of this study was to investigate injured and ill patients’ experiences of cold exposure and to identify related factors. Method During January to March 2011, 62 consecutively selected patients were observed when they were cared for by ambulance nursing staff in prehospital care in the north of Sweden. The field study was based on observations, questions about thermal discomfort and temperature measurements (mattress air and patients’ finger temperature). Based on the observation protocol the participants were divided into two groups, one group that stated it was cold in the patient compartment in the ambulance and another group that did not. Continuous variables were analyzed with independent sample t-test, paired sample t-test and dichotomous variables with cross tabulation. Results In the ambulance 85% of the patients had a finger temperature below comfort zone and 44% experienced the ambient temperature in the patient compartment in the ambulance to be cold. There was a significant decrease in finger temperature from the first measurement indoor compared to measurement in the ambulance. The mattress temperature at the ambulance ranged from −22.3°C to 8.4°C. Conclusion Cold exposure in winter time is common in prehospital care. Sick and injured patients immediately react to cold exposure with decreasing finger temperature and experience of discomfort from cold. Keeping the patient in the comfort zone is of great importance. Further studies are needed to increase knowledge which can be a base for implications in prehospital care for patients who probably already suffer for other reasons. PMID:23742143

Physiological reaction to work in cold microclimate.

PubMed

Bortkiewicz, Alicja; Gadzicka, Elzbieta; Szymczak, Wiesław; Szyjkowska, Agata; Koszada-Włodarczyk, Wiesława; Makowiec-Dabrowska, Teresa

2006-01-01

In Poland, occupational exposure to cold microclimate is quite common (5.1 workers/1000 occupationally active people). Reports on health effects of this exposure are rather scarce. The aim of the study was to evaluate the physiological reaction in workers occupationally exposed to cold microclimate. Examinations were performed in a group of 102 workers (41 women and 61 men) employed at cold storage units. The mean age in the group was 39.1 +/- 9.9 years and the duration of employment under conditions of cold environment was over 12 years. The study population was divided into four groups, according to microclimate conditions (group I, ambient temperature -26 degrees C; group II, 10-14 degrees C; group III, 18-20 degrees C, control group; and group IV, 0-10 degress C). The workers underwent the following procedures: general medical examinations, cold pressor test, ambulatory blood pressure monitoring, and heart rate variability (HRV) analysis (time- and frequency-domain parameters). The results were adjusted for confounding factors (age, smoking and drinking habits). The analysis of HRV parameters did not reveal any significant differences between the study groups. However, systolic and diastolic blood pressure (BP) in the daytime and at night was significantly higher in group IV compared to group II. Mean heart rate (HR) in the daytime and at night and the BP and HR day/night ratio did not differ between the groups. The analysis of BP by gender revealed that in women, systolic BP during the day and at night was significantly higher in group IV than in group II. In the group of workers with hypertension (18 men and 5 women), men reacted to the cold pressor test either by increased or decreased BP while all the women reacted by the increased BP. Our findings indicated that in workers exposed to cold microclimate, the physiological reaction was dependent on gender and ambient temperature. Women seemed to be more sensitive to cold stress than men. However, this finding must be further investigated.

Chronic non-freezing cold injury results in neuropathic pain due to a sensory neuropathy

PubMed Central

Vale, Tom A; Symmonds, Mkael; Polydefkis, Michael; Byrnes, Kelly; Rice, Andrew S C; Themistocleous, Andreas C; Bennett, David L H

2017-01-01

Abstract Non-freezing cold injury develops after sustained exposure to cold temperatures, resulting in tissue cooling but not freezing. This can result in persistent sensory disturbance of the hands and feet including numbness, paraesthesia and chronic pain. Both vascular and neurological aetiologies of this pain have been suggested but remain unproven. We prospectively approached patients referred for clinical assessment of chronic pain following non-freezing cold injury between 12 February 2014 and 30 November 2016. Of 47 patients approached, 42 consented to undergo detailed neurological evaluations including: questionnaires to detail pain location and characteristics, structured neurological examination, quantitative sensory testing, nerve conduction studies and skin biopsy for intraepidermal nerve fibre assessment. Of the 42 study participants, all had experienced non-freezing cold injury while serving in the UK armed services and the majority were of African descent (76.2%) and male (95.2%). Many participants reported multiple exposures to cold. The median time between initial injury and referral was 3.72 years. Pain was principally localized to the hands and the feet, neuropathic in nature and in all study participants associated with cold hypersensitivity. Clinical examination and quantitative sensory testing were consistent with a sensory neuropathy. In all cases, large fibre nerve conduction studies were normal. The intraepidermal nerve fibre density was markedly reduced with 90.5% of participants having a count at or below the 0.05 centile of published normative controls. Using the Neuropathic Pain Special Interest Group of the International Association for the Study of Pain grading for neuropathic pain, 100% had probable and 95.2% definite neuropathic pain. Chronic non-freezing cold injury is a disabling neuropathic pain disorder due to a sensory neuropathy. Why some individuals develop an acute painful sensory neuropathy on sustained cold exposure is not yet known, but individuals of African descent appear vulnerable. Screening tools, such as the DN4 questionnaire, and treatment algorithms for neuropathic pain should now be used in the management of these patients. PMID:28969380

[Effect of erythropoietin on blood oxygen transport in rats during cold exposure and subsequent rewarming].

PubMed

Zinchuk, V V; Glutkin, S V

2010-07-01

Effect of erythropoietin (EPO) preparation (epocrine) on the blood oxygen transport in rats exposed to cold (120 min in a water-cooled box at 19 degrees C) and then rewarmed (next 120 min at a mean heating rate of 0.06 degrees C/min) has been studied. The administration of EPO reduced the body temperature fall at the end of cold exposure and enhanced its rise during the rewarming stage. The effect of EPO in tested rats is associated with a decrease in the hemoglobin affinity to oxygen, which increases the oxygen supply of tissues and improves the organism adaptability to cold.

Tested Demonstrations. The Stepwise Reduction of Permanganate in Alkaline Conditions: A Lecture Demonstration.

ERIC Educational Resources Information Center

Ruoff, Peter; Riley, Megan

1987-01-01

Describes a chemistry experiment where an alkaline ice-cold permanganate solution is reduced by adding dropwise a cold diluted hydrogen peroxide solution. Outlines the course of the reduction through the various oxidation states of manganese with their characteristic colors. (TW)

Evolution of CO2 and H2O on Mars: A cold Early History?

NASA Technical Reports Server (NTRS)

Niles, P. B.; Michalski, J.

2011-01-01

The martian climate has long been thought to have evolved substantially through history from a warm and wet period to the current cold and dry conditions on the martian surface. This view has been challenged based primarily on evidence that the early Sun had a substantially reduced luminosity and that a greenhouse atmosphere would be difficult to sustain on Mars for long periods of time. In addition, the evidence for a warm, wet period of martian history is far from conclusive with many of the salient features capable of being explained by an early cold climate. An important test of the warm, wet early Mars hypothesis is the abundance of carbonates in the crust [1]. Recent high precision isotopic measurements of the martian atmosphere and discoveries of carbonates on the martian surface provide new constraints on the evolution of the martian atmosphere. This work seeks to apply these constraints to test the feasibility of the cold early scenario

The study on a gas-coupled two-stage stirling-type pulse tube cryocooler

NASA Astrophysics Data System (ADS)

Wu, X. L.; Chen, L. B.; Zhu, X. S.; Pan, C. Z.; Guo, J.; Wang, J. J.; Zhou, Y.

2017-12-01

A two-stage gas-coupled Stirling-type pulse tube cryocooler (SPTC) driven by a linear dual-opposed compressor has been designed, manufactured and tested. Both of the stages adopted coaxial structure for compactness. The effect of a cold double-inlet at the second stage on the cooling performance was investigated. The test results show that the cold double-inlet will help to achieve a lower cooling temperature, but it is not conducive to achieving a higher cooling capacity. At present, without the cold double-inlet, the second stage has achieved a no-load temperature of 11.28 K and a cooling capacity of 620 mW/20 K with an input electric power of 450 W. With the cold double-inlet, the no-load temperature is lowered to 9.4 K, but the cooling capacity is reduced to 400 mW/20 K. The structure of the developed cryocooler and the influences of charge pressure, operating frequency and hot end temperature will also be introduced in this paper.

Induced vasodilation as treatment for Raynaud's disease.

PubMed

Jobe, J B; Sampson, J B; Roberts, D E; Beetham, W P

1982-11-01

We examined the efficacy of induced vasodilation as a treatment of idiopathic Raynaud's disease. Eight persons with Raynaud's disease and seven normal persons each received 27 simultaneous pairings of hand immersion in warm water (43 degrees C) for 10 minutes with exposure of the whole body to cold (0 degrees C). A second group of seven normal persons and nine persons with Raynaud's disease received no treatments. All subjects had cold test exposures (0 degrees C) at the start and end of the study. Subjects with Raynaud's disease who received treatments showed significant increases in digital temperatures (2.2 degrees C) during the cold test compared with the values of untreated subjects with Raynaud's disease (p less than 0.05); normal subjects who had received treatments showed no difference from those who had not. Digital temperatures of subjects with Raynaud's disease after treatment increased to levels approaching those of normal subjects, although they showed lower digital temperatures during initial exposure to cold (p less than 0.01). This therapy offers a practical alternative to traditional treatments.

[Clinical evaluation of Olbas oil effect on nasal mucosa in acute rhinitis patients during common cold].

PubMed

Zalewski, P; Olszewski, J; Olszewska-Ziaber, A; Zielińska-Bliźniewska, H; Pietkiewicz, P

1997-01-01

The aim of the study was the clinical evaluation of the effect of Olbas oil on nasal mucosa in patients with acute rhinitis during common cold. 15 patients with 2-3 days history of acute rhinitis during common cold, both sexes, in the age between 23-47 were investigated. All the examinations were done before using, after the first inhalation, and after 7 days of Olbas oil administration. The investigation before using Olbas oil was comprised of: history data, general and otorhinolaryngological examination with particular evaluation of nasal mucosa, anterior rhinomanometry, saccharin translocation time, olfactometry, microbiological cultures, histamine nasal provocation test. At the end, after 7 days of Olbas oil inhalation 3 times a day for 4 minutes 4 drops of Olbas oil applied into a handkerchief, all the test were done again, as at the beginning. The study showed a good of the effect of Olbas oil on nasal mucosa in patients with acute rhinitis during common cold.

Maximising platelet availability by delaying cold storage.

PubMed

Wood, B; Johnson, L; Hyland, R A; Marks, D C

2018-04-06

Cold-stored platelets may be an alternative to conventional room temperature (RT) storage. However, cold-stored platelets are cleared more rapidly from circulation, reducing their suitability for prophylactic transfusion. To minimise wastage, it may be beneficial to store platelets conventionally until near expiry (4 days) for prophylactic use, transferring them to refrigerated storage to facilitate an extended shelf life, reserving the platelets for the treatment of acute bleeding. Two ABO-matched buffy-coat-derived platelets (30% plasma/70% SSP+) were pooled and split to produce matched pairs (n = 8 pairs). One unit was stored at 2-6°C without agitation (day 1 postcollection; cold); the second unit was stored at 20-24°C with constant agitation until day 4 then stored at 2-6°C thereafter (delayed-cold). All units were tested for in vitro quality periodically over 21 days. During storage, cold and delayed-cold platelets maintained a similar platelet count. While pH and HSR were significantly higher in delayed-cold platelets, other metabolic markers, including lactate production and glucose consumption, did not differ significantly. Furthermore, surface expression of phosphatidylserine and CD62P, release of soluble CD62P and microparticles were not significantly different, suggesting similar activation profiles. Aggregation responses of delayed-cold platelets followed the same trend as cold platelets once transferred to cold storage, gradually declining over the storage period. The metabolic and activation profile of delayed-cold platelets was similar to cold-stored platelets. These data suggest that transferring platelets to refrigerated storage when near expiry may be a viable option for maximising platelet inventories. © 2018 International Society of Blood Transfusion.

Mental and cognitive performance in the cold.

PubMed

Palinkas, L A

2001-08-01

Vigilance, attention, memory, and motivation are essential to adapting to the physiological changes that occur with prolonged exposure to the cold and to avoiding both the environmental hazards associated with cold and the health-related consequences of these hazards. This paper summarizes the effects of cold temperatures on cognitive performance and mood. Although the effects of hypothermic-induced cold temperatures on cognitive performance and mood have been well documented, evidence of nonhypothermic effects has been inconsistent. There is evidence of a dose-response relation involving decrements in cognitive performance with respect to decline in core body temperature and complexity of tasks performed. However, it is unclear whether these effects are due to distraction or increased arousal. Likewise, further research is required to test the efficacy of existing and proposed pharmacologic and nutritional countermeasures.

Blood pressure and endocrine responses of healthy subjects in cold pressor test after acutely increased dietary sodium intake.

PubMed

Arjamaa, O; Mäkinen, T; Turunen, L; Huttunen, P; Leppäluoto, J; Vuolteenaho, O; Rintamäki, H

2001-05-01

The objective of the study was to compare blood pressure and endocrine responses in a cold pressure test in young healthy subjects who had shown increased blood pressure during an acutely increased sodium intake. Subjects (n = 53) added 121 mmol sodium into their normal diet for one week. If the mean arterial pressure had increased by a minimum of 5 mmHg compared to the control measure, they were selected for the experiments. The selected subjects (n = 8) were given 121 mmol supplemental sodium d-1 for 14 days after which they immersed the right hand into a cold (+10 degrees C) water bath for 5 min. The blood pressure increased (P < 0.05) during the test and was independent of the sodium intake. The plasma noradrenaline increased from 2.41 +/- 0.38 nmol l-1 to 2.82 +/- 0.42 nmol l-1 (P < 0.05) with normal diet and from 1.85 +/- 0.29 nmol l-1 to 2.40 +/- 0.37 nmol l-1 (P < 0.05) with high sodium diet. The starting concentrations and the endpoint concentrations were statistically similar. The plasma levels of natriuretic peptides (NT-proANP, ANP and BNP) did not change during the test, and the concentrations were independent of the sodium diet. To conclude, acutely increased sodium intake does not change blood pressure or hormonal responses in a cold pressor test in young healthy subjects.

Effect of acute transdermal estrogen administration on basal, mental stress and cold pressor-induced sympathetic responses in postmenopausal women.

PubMed

Sofowora, Gbemiga G; Singh, Iqbal; He, Huai B; Wood, Alastair J J; Stein, C Michael

2005-06-01

Administration of estrogen has vascular effects through poorly defined mechanisms that may include sympathetic withdrawal. To define the effects of acute estrogen administration on sympathetic responses, nineteen healthy postmenopausal women (age 54+/-2 years) were studied after application of a placebo or estrogen patch for 36 hours, in random order. A p-value, adjusted for multiple comparisons, of <0.017 was used to determine statistical significance. Heart rate, blood pressure, and norepinephrine spillover were measured at rest, during mental stress (Stroop test), and during a cold pressor test. Estrogen did not attenuate basal or stimulated hemodynamic responses significantly. The increase in mean arterial pressure after the Stroop test (5.9+/-1.2mm/ Hg on placebo vs 6.1+/-1.6mm/Hg on estrogen, p=0.9) and after the cold pressor test (12.6+/-2.4mm/Hg on placebo vs 13.0+/-2.2 mm/Hg on estrogen, p=0.8) did not differ. Basal, mental stress and cold pressor-stimulated norepinephrine spillover were not significantly affected by short-term estrogen administration. Norepinephrine spillover tended to be higher after estrogen (1296.2+/-238 ng/min) than placebo (832.5+/-129 ng/min) (p=0.02) at baseline and after the Stroop test (1881.1+/-330 ng/min vs 1014.6+/-249 ng/min) (p=0.02). Acute transdermal estrogen administration did not attenuate norepinephrine spillover or sympathetically mediated hemodynamic responses.

[Physicians with access to point-of-care tests significantly reduce the antibiotic prescription for common cold].

PubMed

Llor, Carles; Hernández, Silvia; Cots, Josep María; Bjerrum, Lars; González, Beatriz; García, Guillermo; Alcántara, Juan de Dios; Guerra, Gloria; Cid, Marina; Gómez, Manuel; Ortega, Jesús; Pérez, Carolina; Arranz, Javier; Monedero, María José; Paredes, José; Pineda, Vicenta

2013-03-01

This study was aimed at evaluating the effect of two levels of intervention on the antibiotic prescribing in patients with common cold. Before and after audit-based study carried out in primary healthcare centres in Spain. General practitioners registered all the episodes of common cold during 15 working days in January and February in 2008 (preintervention). Two types of intervention were considered: full intervention, consisting in individual feedback based on results from the first registry, courses in rational antibiotic prescribing, guidelines, patient information leaflets, workshops on rapid tests -rapid antigen detection and C-reactive protein tests- and provision of these tests in the surgeries; and partial intervention, consisting of all the above intervention except for the workshop and they did not have access to rapid tests. The same registry was repeated in 2009 (postintervention). In addition, new physicians filled out only the registry in 2009 (control group). 210 physicians underwent the full intervention, 71 the partial intervention and 59 were assigned to the control group. The 340 doctors prescribed antibiotics in 274 episodes of a total of 12,373 cases registered (2.2%).The greatest percentage of antibiotic prescription was found in the control group (4.6%). The partial intervention increased the antibiotic prescription percentage from 1.1% to 2.7% while only doctors who underwent the complete intervention lead to a significant reduction of antibiotics prescribed, from 2.9% before to 0.7% after the intervention (p<0.001). Only physicians with access to rapid tests significantly reduced antibiotic prescription in patients with common cold.

Reactor Simulator Testing Overview

NASA Technical Reports Server (NTRS)

Schoenfeld, Michael P.

2013-01-01

Test Objectives Summary: a) Verify operation of the core simulator, the instrumentation & control system, and the ground support gas and vacuum test equipment. b) Examine cooling & heat regeneration performance of the cold trap purification. c) Test the ALIP pump at voltages beyond 120V to see if the targeted mass flow rate of 1.75 kg/s can be obtained in the RxSim. Testing Highlights: a) Gas and vacuum ground support test equipment performed effectively for operations (NaK fill, loop pressurization, and NaK drain). b) Instrumentation & Control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings and ramped within prescribed constraints. It effectively interacted with reactor simulator control model and defaulted back to temperature control mode if the transient fluctuations didn't dampen. c) Cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained which was lower than the predicted 750 K but 156 K higher than the minimum temperature indicating the design provided some heat regeneration. d) ALIP produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz.

Changes in cold tolerance due to a 14-day stay in the Canadian Arctic

NASA Astrophysics Data System (ADS)

Livingstone, S. D.; Romet, T.; Keefe, A. A.; Nolan, R. W.

1996-12-01

Responses to cold exposure tests both locally and of the whole body were examined in subjects who stayed in the Arctic (average maximum and minimum temperatures -11 and -21° C respectively) for 14 days of skiing and sleeping in tents. These changes were compared to responses in subjects living working in Ottawa, Canada (average max. and min. temperatures -5 and -11° C respectively). The tests were done before the stay in the Arctic (Pre), immediately after the return (Post 1) and approximately 32 days after the return (Post 2). For the whole-body cold exposure each subject, wearing only shorts and lying on a rope mesh cot, was exposed to an ambient temperature of 10° C. There was no consistent response in the changes of metabolic or body temperature to this exposure in either of groups and, in addition, the changes over time were variable. Cold induced vasodilatation (CIVD) was determined by measuring temperature changes in the middle finger of the nondominant hand upon immersion in ice water for 30 min. CIVD was depressed after the Arctic exposure whilst during the Post 2 testing, although variable, did not return to the Pre values; the responses of the control group were similar. These results indicate that normal seasonal changes may be as important in adaptation as a stay in the Arctic. Caution is advised in the separation of seasonal effects when examining the changes in adaptation after exposure to a cold environment.

Changes in cold tolerance due to a 14-day stay in the Canadian Arctic.

PubMed

Livingstone, S D; Romet, T; Keefe, A A; Nolan, R W

1996-11-01

Response to cold exposure tests both locally and of the whole body were examined in subjects who stayed in the arctic (average maximum and minimum temperatures -11 and -21 degrees C respectively) for 14 days of skiing and sleeping in tents. These changes were compared to responses in subjects living working in Ottawa, Canada (average max. and min. temperatures -5 and -11 degrees C respectively). The tests were done before the stay in the Arctic (Pre), immediately after the return (Post 1) and approximately 32 days after the return (Post 2). For the whole-body cold exposure each subject, wearing only shorts and lying on a rope mesh cot, was exposed to an ambient temperature of 10 degrees C. There was no consistent response in the changes of metabolic or body temperature to this exposure in either of groups and, in addition, the changes over time were variable. Cold induced vasodilatation (CIVD) was determined by measuring temperature changes in the middle finger of the nondominant hand upon immersion in ice water for 30 min. CIVD was depressed after the Arctic exposure whilst during the Post 2 testing, although variable, did not return to the Pre values; the responses of the control group were similar. These results indicate that normal seasonal changes may be as important in adaptation as a stay in the Arctic. Caution is advised in the separation of seasonal effects when examining the changes in adaptation after exposure to a cold environment.

Evaluation of outgassing, tear strength, and detail reproduction in alginate substitute materials.

PubMed

Baxter, R T; Lawson, N C; Cakir, D; Beck, P; Ramp, L C; Burgess, J O

2012-01-01

To compare three alginate substitute materials to an alginate impression material for cast surface porosity (outgassing), tear strength, and detail reproduction. Detail reproduction tests were performed following American National Standards Institute/American Dental Association (ANSI/ADA) Specification No. 19. To measure tear strength, 12 samples of each material were made using a split mold, placed in a water bath until testing, and loaded in tension until failure at a rate of 500 mm/min using a universal testing machine. For cast surface porosity testing, five impressions of a Teflon mold with each material were placed in a water bath (37.8°C) for the in-mouth setting time and poured with vacuum-mixed Silky Rock die stone at 5, 10, 30, and 60 minutes from the start of mixing. The gypsum samples were analyzed with a digital microscope for surface porosity indicative of hydrogen gas release by comparing the surface obtained at each interval with four casts representing no, little, some, and significant porosity. Data analysis was performed using parametric and Kruskal-Wallis analysis of variance (ANOVA), Tukey/Kramer post-hoc tests (α=0.05), and individual Mann-Whitney U tests (α=0.0167). All alginate substitute materials passed the detail reproduction test. Tear strength of the alginate substitute materials was significantly better than alginate and formed three statistically different groups: AlgiNot had the lowest tear strength, Algin-X Ultra had the highest tear strength, and Position Penta Quick had intermediate tear strength. Significant variation in outgassing existed between materials and pouring times (p<0.05). All alginate substitute materials exhibited the least outgassing and cast porosity 60 minutes after mixing. Detail reproduction and tear strength of alginate substitute materials were superior to traditional alginate. The outgassing effect was minimal for most materials tested. Alginate substitute materials are superior replacements for irreversible hydrocolloid.

Caracterisation environnementale des emissions atmospheriques d'une source fixe et creation d'un outil de gestion dynamique =

NASA Astrophysics Data System (ADS)

Fournier, Marie-Claude

Une caracterisation des emissions atmospheriques provenant des sources fixes en operation, alimentees au gaz et a l'huile legere, a ete conduite aux installations visees des sites no.1 et no.2. La caracterisation et les calculs theoriques des emissions atmospheriques aux installations des sites no.1 et no.2 presentent des resultats qui sont en dessous des valeurs reglementaires pour des conditions d'operation normales en periode hivernale et par consequent, a de plus fortes demandes energetiques. Ainsi, pour une demande energetique plus basse, le taux de contaminants dans les emissions atmospheriques pourrait egalement etre en dessous des reglementations municipales et provinciales en vigueur. Dans la perspective d'une nouvelle reglementation provinciale, dont les termes sont discutes depuis 2005, il serait souhaitable que le proprietaire des infrastructures visees participe aux echanges avec le Ministere du Developpement Durable, de l'Environnement et des Parcs (MDDEP) du Quebec. En effet, meme si le principe de droit acquis permettrait d'eviter d'etre assujetti a la nouvelle reglementation, l'application de ce type de principe ne s'inscrit pas dans ceux d'un developpement durable. L'âge avance des installations etudiees implique la planification d'un entretien rigoureux afin d'assurer les conditions optimales de combustion en fonction du type de combustible. Des tests de combustion sur une base reguliere sont donc recommandes. Afin de supporter le processus de suivi et d'evaluation de la performance environnementale des sources fixes, un outil d'aide a la gestion de l'information environnementale a ete developpe. Dans ce contexte, la poursuite du developpement d'un outil d'aide a la gestion de l'information environnementale faciliterait non seulement le travail des personnes affectees aux inventaires annuels mais egalement le processus de communication entre les differents acteurs concernes tant intra- qu'inter-etablissement. Cet outil serait egalement un bon moyen pour sensibiliser le personnel a leur consommation energetique ainsi qu'a leur role dans la lutte contre les emissions polluantes et les gaz a effets de serre. En outre, ce type d'outil a pour principale fonction de generer des rapports dynamiques pouvant s'adapter a des besoins precis. Le decoupage coherent de l'information associe a un developpement par modules offre la perspective d'application de l'outil pour d'autres types d'activites. Dans ce cas, il s'agit de definir la part commune avec les modules existants et planifier les activites de developpement specifiques selon la meme demarche que celle presentee dans le present document.

Maximum heat of mass concrete - phase 2 [summary].

DOT National Transportation Integrated Search

2016-12-01

Concrete hardens through a chemical reaction that produces heat and expansion, followed by contraction as the concrete cools. Concrete near the edge of a pour cools faster and shrinks earlier than concrete further from the edge. Most concrete pours a...

Aircraft Disinsection: A Guide for Military and Civilian Air Carriers (Desinsectisation des aeronefs: Un guide a l’intention des responsables des transports aeriens civils et militaires)

DTIC Science & Technology

1996-04-01

regulations. - Ceratitis capitata (Mediterranean fruit fly). Quarantine regulations generally reduce - Rhagoletis pomonella (Apple maggot). the chances of a...d’insectes nuisibles dans un pays, en 6vitant des risques pour la sant6 des 6quipages, pour la s~curit6 de 1’a~ronef et pour l’industrie. Ce rapport examine 1...diffrrents officiels responsables de la r~glementation des insectes nuisibles introduits, de l’inscription des pesticides et de leur utilisation en

Special Course on Inverse Methods for Airfoil Design for Aeronautical and Turbomachinery Applications (Methodes Inverses pour la Conception des Profils Porteurs pour des Applications dans les Domaines de l’Aeronautique et des Turbomachines)

DTIC Science & Technology

1990-11-01

engined jet aircraft wing MID PLA CROSS tCTO% taking into account the effects of the propulsive system. -DESIGN PAAMETERS DESTIGE PARAMETERS 5CT 0 (MC 0...AGARD Report No.780 Special Course on Inverse Methods for Airfoil Design for Aeronautical and Turbomachinery Applications (M6thodes Inverses pour la...manufacturing systems. Blade or airfoil designs are normally made in two steps, and the lectures are accordingly grouped into two parts. - - In the

Automated Software Generation Approaches for the Design and Development of Guidance and Control Systems Software (Les Differentes Approches Generation pour la Conception et le Developpement de Logiciels de Guidage et de Pilotage)

DTIC Science & Technology

1992-03-01

de Logiciels") etaient en cours de developpement pour resoudre des problimes similaires dans le monde de la gestion . le Panel... gestion des sp cifications, d’algorithmes et de reprtsentations. Techniques et Sciences Informatiques, 4(3), 1985. 4-21 R. Jacquart, M. Lemoine, and G...Guidance and Control Systems Software (Les Diff~rentes Approches "G6neration" pour la Conception et le D~veloppement de Logiciels de Guidage et de

Internal Blast in a Compartment-type Vessel. Part 1: Finite Element Modeling Investigation

DTIC Science & Technology

2012-11-01

données expérimentales devraient aussi être utilisées pour valider le modèle. DRDC Valcartier TM 2012-222 iii Executive summary Internal...pour simuler adéquatement le souffle d’explosion, incluant le choc et ses réflexions, à l’intérieur d’une large structure et le besoin de remédier à...terme, le développement et la validation d’un ‘raytracer’ et son couplage avec LS-DYNA seront étudiés pour modéliser le choc dans le compartiment

A Statistical Treatment of Bioassay Pour Fractions

NASA Technical Reports Server (NTRS)

Barengoltz, Jack; Hughes, David W.

2014-01-01

The binomial probability distribution is used to treat the statistics of a microbiological sample that is split into two parts, with only one part evaluated for spore count. One wishes to estimate the total number of spores in the sample based on the counts obtained from the part that is evaluated (pour fraction). Formally, the binomial distribution is recharacterized as a function of the observed counts (successes), with the total number (trials) an unknown. The pour fraction is the probability of success per spore (trial). This distribution must be renormalized in terms of the total number. Finally, the new renormalized distribution is integrated and mathematically inverted to yield the maximum estimate of the total number as a function of a desired level of confidence ( P(

Spectrometre de masse a ionisation Penning selective: Elimination des corrections necessaires a la determination du rapport isotopique de l'hydrogene

NASA Astrophysics Data System (ADS)

Letarte, Sylvain

Dans le but d'ameliorer la precision avec laquelle le rapport isotopique de l'hydrogene peut etre determine, un spectrometre de masse a ionisation Penning a ete construit pour provoquer l'ionisation selective de l'hydrogene moleculaire et de l'hydrure de deuterium a partir d'un melange gazeux. L'utilisation d'atomes dans des etats d'excitation metastable s'est averee une solution adequate pour reponde a cette attente. L'emploi de l'helium, a l'interieur d'une source d'atomes metastables construit specifiquement pour ce travail, ne permet pas d'obtenir un spectre de masse compose uniquement des deux molecules d'interet. L'ionisation de ces dernieres provient de deux processus distincts, soient l'ionisation Penning et l'ionisation par bombardement electronique. Contrairement a l'helium, il a ete demontre que le neon metastable est un candidat ideal pour produire l'ionisation selective de type Penning. Le nombre d'ions produits est directement proportionnel au courant de la decharge electrique et de la pression d'operation de la source d'atomes metastables. Ces resultats demontrent le potentiel d'un tel spectrometre de masse pour ameliorer la precision a laquelle le rapport isotopique peut etre determine comparativement aux autres techniques existantes.

Utilisation d'images aeroportees a tres haute resolution spatiale pour l'estimation de la vigueur des peuplements forestiers du nord-ouest du Nouveau-Brunswick

NASA Astrophysics Data System (ADS)

Louis, Ognel Pierre

Le but de cette etude est de developper un outil permettant d'estimer le niveau de risque de perte de vigueur des peuplements forestiers de la region de Gounamitz au nord-ouest du Nouveau-Brunswick via des donnees d'inventaires forestiers et des donnees de teledetection. Pour ce faire, un marteloscope de 100m x 100m et 20 parcelles d'echantillonnages ont ete delimites. A l'interieur de ces derniers, le niveau de risque de perte de vigueur des arbres ayant un DHP superieur ou egal a 9 cm a ete determine. Afin de caracteriser le risque de perte de vigueur des arbres, leurs positions spatiales ont ete repertoriees a partir d'un GPS en tenant compte des defauts au niveau des tiges. Pour mener a bien ce travail, les indices de vegetation et de textures et les bandes spectrales de l'image aeroportee ont ete extraits et consideres comme variables independantes. Le niveau de risque de perte de vigueur obtenu par espece d'arbre a travers les inventaires forestiers a ete considere comme variable dependante. En vue d'obtenir la superficie des peuplements forestiers de la region d'etude, une classification dirigee des images a partir de l'algorithme maximum de vraisemblance a ete effectuee. Le niveau de risque de perte de vigueur par type d'arbre a ensuite ete estime a l'aide des reseaux de neurones en utilisant un reseau dit perceptron multicouches. Il s'agit d'un modele de reseau de neurones compose de : 11 neurones sur la couche d'entree, correspondant aux variables independantes, 35 neurones sur la couche cachee et 4 neurones sur la couche de sortie. La prediction a partir des reseaux de neurones produit une matrice de confusion qui permet d'obtenir des mesures quantitatives d'estimation, notamment un pourcentage de classification globale de 91,7% pour la prediction du risque de perte de vigueur du peuplement de resineux et de 89,7% pour celui du peuplement de feuillus. L'evaluation de la performance des reseaux de neurones fournit une valeur de MSE globale de 0,04, et une RMSE (Mean Square Error) globale de 0,20 pour le peuplement de feuillus. Quant au peuplement de resineux, une valeur de MSE (Mean Square Error) globale de 0,05 et une valeur de RMSE globale de 0,22 ont ete obtenues. Pour la validation des resultats, le niveau de risque de perte de vigueur predit a ete compare avec le risque de perte de vigueur de reference. Les resultats obtenus donnent un coefficient de determination de 0,98 pour le peuplement de feuillus et 0,93 pour le peuplement de resineux.

La prise en charge des troubles de santé mentale par les omnipraticiens du Québec

PubMed Central

Fleury, Marie-Josée; Farand, Lambert; Aubé, Denise; Imboua, Armelle

2012-01-01

Résumé Objectif Cette recherche vise à documenter la prise en charge des troubles mentaux (TM) par les omnipraticiens. Type d’étude Il s’agit d’une étude mixte intégrant un questionnaire auto-administré et des entrevues qualitatives. La banque de données administratives des actes médicaux de la Régie de l’assurance maladie du Québec a aussi été analysée. Contexte La province de Québec. Participants Un total de 1415 omnipraticiens de différents lieux de pratiques ont été sollicités pour le questionnaire; 970 ont été rejoints. Un sous-groupe de 60 omnipraticiens a été rejoint pour les entrevues. Principaux paramètres à l'étude La prévalence annuelle des consultations reliées à des TM courants (TMC) ou graves (TMG), les pratiques cliniques, les pratiques de collaboration, les facteurs facilitant ou entravant la prise en charge des TM, ainsi que les recommandations pour l’amélioration du système de soins. Résultats Le taux de réponse a été de 41% (n = 398 omnipraticiens) pour le questionnaire et de 63% (n = 60) pour les entrevues. Environ 25 % des visites chez les omnipraticiens sont associées à des TM. Presque tous les omnipraticiens prennent en charge des TMC et se sentent compétents pour le faire, à l’inverse de la situation retrouvée pour les TMG. Près de 20 % des TMC sont référés (principalement à des intervenants psychosociaux), alors que près de 75 % des TMG sont référés (surtout en psychiatrie et à l’urgence). Plus de 50 % des omnipraticiens affirment n’entretenir aucun contact avec l’une ou l’autre des ressources de santé mentale. Plusieurs facteurs influencent la prise en charge des TM: les profils des patients (complexité des TM, troubles concomitants); les caractéristiques des omnipraticiens (réseau informel, formation); la culture professionnelle (travail en silo, mécanismes cliniques formalisés); le milieu institutionnel (multidisciplinarité, salariat); l’organisation des services (ressources; coordination formalisée) et l’environnement (politiques). Conclusion Le rôle clé des omnipraticiens et leur soutien à la prise en charge des TM ont été démontrés, spécifiquement pour les TMC. Pour une prise en charge optimale des soins primaires de santé mentale, des stratégies à composantes multiples, dont les soins partagés, devraient être davantage déployées.

Lignes directrices canadiennes sur l’utilisation sécuritaire et efficace des opioïdes pour la douleur chronique non cancéreuse

PubMed Central

Kahan, Meldon; Mailis-Gagnon, Angela; Wilson, Lynn; Srivastava, Anita

2011-01-01

Résumé Objectif Présenter aux médecins de famille un résumé clinique pratique des lignes directrices canadiennes sur l’utilisation sécuritaire et efficace des opioïdes pour la douleur chronique non cancéreuse, produites par le National Opioid Use Guideline Group. Qualité des données Pour produire les lignes directrices, les chercheurs ont effectué une synthèse critique de la littérature médicale sur l’efficacité et l’innocuité des opioïdes pour la douleur chronique non cancéreuse et ont rédigé une série de recommandations. Un panel de 49 cliniciens experts de toutes les régions du Canada ont passé en revue l’ébauche et ont atteint un consensus sur 24 recommandations. Message principal Il est recommandé de faire un dépistage du risque de dépendance avant de prescrire des opioïdes. On recommande des opioïdes faibles (codéine et tramadol) pour une douleur de légère à modérée qui n’a pas répondu aux traitements de première intention. On peut essayer l’oxycodone, l’hydromorphone et la morphine chez les patients qui n’ont pas eu de soulagement avec des opioïdes plus faibles. Une faible dose initiale et une lente hausse du titrage sont recommandées, ainsi qu’une étroite surveillance du patient qu’on a d’abord renseigné. Les médecins doivent surveiller l’apparition de complications comme l’apnée du sommeil. La dose optimale est celle qui améliore le fonctionnement ou atténue les cotes d’évaluation de la douleur d’au moins 30 %. Pour la grande majorité des patients, la dose optimale sera bien en deçà de l’équivalent de 200 mg de morphine par jour. On recommande le sevrage progressif pour les patients qui n’ont pas répondu à un essai d’opioïdes adéquat. Conclusion Les opioïdes jouent un rôle important dans la prise en charge de la douleur chronique non cancéreuse, mais il faut en prescrire avec prudence pour limiter les dommages potentiels. Les nouvelles lignes directrices canadiennes offrent des conseils dont les médecins avaient grand besoin pour les aider à en arriver à un juste équilibre entre le contrôle optimal de la douleur et la sécurité.

Effets de l'humidite sur la propagation du delaminage dans un composite carbone/epoxy sollicite en mode mixte I/II

NASA Astrophysics Data System (ADS)

LeBlanc, Luc R.

Les materiaux composites sont de plus en plus utilises dans des domaines tels que l'aerospatiale, les voitures a hautes performances et les equipements sportifs, pour en nommer quelques-uns. Des etudes ont demontre qu'une exposition a l'humidite nuit a la resistance des composites en favorisant l'initiation et la propagation du delaminage. De ces etudes, tres peu traitent de l'effet de l'humidite sur l'initiation du delaminage en mode mixte I/II et aucune ne traite des effets de l'humidite sur le taux de propagation du delaminage en mode mixte I/II dans un composite. La premiere partie de cette these consiste a determiner les effets de l'humidite sur la propagation du delaminage lors d'une sollicitation en mode mixte I/II. Des eprouvettes d'un composite unidirectionnel de carbone/epoxy (G40-800/5276-1) ont ete immergees dans un bain d'eau distillee a 70°C jusqu'a leur saturation. Des essais experimentaux quasi-statiques avec des chargements d'une gamme de mixites des modes I/II (0%, 25%, 50%, 75% et 100%) ont ete executes pour determiner les effets de l'humidite sur la resistance au delaminage du composite. Des essais de fatigue ont ete realises, avec la meme gamme de mixite des modes I/II, pour determiner 1'effet de 1'humidite sur l'initiation et sur le taux de propagation du delaminage. Les resultats des essais en chargement quasi-statique ont demontre que l'humidite reduit la resistance au delaminage d'un composite carbone/epoxy pour toute la gamme des mixites des modes I/II, sauf pour le mode I ou la resistance au delaminage augmente apres une exposition a l'humidite. Pour les chargements en fatigue, l'humidite a pour effet d'accelerer l'initiation du delaminage et d'augmenter le taux de propagation pour toutes les mixites des modes I/II. Les donnees experimentales recueillies ont ete utilisees pour determiner lesquels des criteres de delaminage en statique et des modeles de taux de propagation du delaminage en fatigue en mode mixte I/II proposes dans la litterature representent le mieux le delaminage du composite etudie. Une courbe de regression a ete utilisee pour determiner le meilleur ajustement entre les donnees experimentales et les criteres de delaminage en statique etudies. Une surface de regression a ete utilisee pour determiner le meilleur ajustement entre les donnees experimentales et les modeles de taux de propagation en fatigue etudies. D'apres les ajustements, le meilleur critere de delaminage en statique est le critere B-K et le meilleur modele de propagation en fatigue est le modele de Kenane-Benzeggagh. Afin de predire le delaminage lors de la conception de pieces complexes, des modeles numeriques peuvent etre utilises. La prediction de la longueur de delaminage lors des chargements en fatigue d'une piece est tres importante pour assurer qu'une fissure interlaminaire ne va pas croitre excessivement et causer la rupture de cette piece avant la fin de sa duree de vie de conception. Selon la tendance recente, ces modeles sont souvent bases sur l'approche de zone cohesive avec une formulation par elements finis. Au cours des travaux presentes dans cette these, le modele de progression du delaminage en fatigue de Landry & LaPlante (2012) a ete ameliore en y ajoutant le traitement des chargements en mode mixte I/II et en y modifiant l'algorithme du calcul de la force d'entrainement maximale du delaminage. Une calibration des parametres de zone cohesive a ete faite a partir des essais quasi-statiques experimentaux en mode I et II. Des resultats de simulations numeriques des essais quasi-statiques en mode mixte I/II, avec des eprouvettes seches et humides, ont ete compares avec les essais experimentaux. Des simulations numeriques en fatigue ont aussi ete faites et comparees avec les resultats experimentaux du taux de propagation du delaminage. Les resultats numeriques des essais quasi-statiques et de fatigue ont montre une bonne correlation avec les resultats experimentaux pour toute la gamme des mixites des modes I/II etudiee.

Using a Cold Radiometer to Measure Heat Loads and Survey Heat Leaks

NASA Technical Reports Server (NTRS)

Dipirro, M.; Tuttle, J.; Hait, T.; Shirron, P.

2014-01-01

We have developed an inexpensive cold radiometer for use in thermal/vacuum chambers to measure heat loads, characterize emissivity and specularity of surfaces and to survey areas to evaluate stray heat loads. We report here the results of two such tests for the James Webb Space Telescope to measure heat loads and effective emissivities of 2 major pieces of optical ground support equipment that will be used in upcoming thermal vacuum testing of the Telescope.

Using a Cold Radiometer to Measure Heat Loads and Survey Heat Leaks

NASA Technical Reports Server (NTRS)

DiPirro, M.; Tuttle, J.; Hait, T.; Shirron, P.

2013-01-01

We have developed an inexpensive cold radiometer for use in thermal/vacuum chambers to measure heat loads, characterize emissivity and specularity of surfaces and to survey areas to evaluate stray heat loads. We report here the results of two such tests for the James Webb Space Telescope to measure heat loads and effective emissivities of2 major pieces of optical ground support equipment that will be used in upcoming thermal vacuum testing of the Telescope.

Differential pain modulation in patients with peripheral neuropathic pain and fibromyalgia.

PubMed

Gormsen, Lise; Bach, Flemming W; Rosenberg, Raben; Jensen, Troels S

2017-12-29

Background The definition of neuropathic pain has recently been changed by the International Association for the Study of Pain. This means that conditions such as fibromyalgia cannot, as sometimes discussed, be included in the neuropathic pain conditions. However, fibromyalgia and peripheral neuropathic pain share common clinical features such as spontaneous pain and hypersensitivity to external stimuli. Therefore, it is of interest to directly compare the conditions. Material and methods In this study we directly compared the pain modulation in neuropathic pain versus fibromyalgia by recording responses to a cold pressor test in 30 patients with peripheral neuropathic pain, 28 patients with fibromyalgia, and 26 pain-free age-and gender-matched healthy controls. Patients were asked to rate their spontaneous pain on a visual analog scale (VAS (0-100 mm) immediately before and immediately after the cold pressor test. Furthermore the duration (s) of extremity immersion in cold water was used as a measure of the pain tolerance threshold, and the perceived pain intensity at pain tolerance on the VAS was recorded on the extremity in the water after the cold pressor test. In addition, thermal (thermo tester) and mechanical stimuli (pressure algometer) were used to determine sensory detection, pain detection, and pain tolerance thresholds in different body parts. All sensory tests were done by the same examiner, in the same room, and with each subject in a supine position. The sequence of examinations was the following: (1) reaction time, (2) pressure thresholds, (3) thermal thresholds, and (4) cold pressor test. Reaction time was measured to ensure that psychomotoric inhibitions did not influence pain thresholds. Results Pain modulation induced by a cold pressor test reduced spontaneous pain by 40% on average in neuropathic pain patients, but increased spontaneous pain by 2.6% in fibromyalgia patients. This difference between fibromyalgia and neuropathic pain patients was significant (P < 0.002). Fibromyalgia patients withdrew their extremity from the cold water significantly earlier than neuropathic pain patients and healthy controls; however, they had a higher perceived pain intensity on the VAS than neuropathic pain patients and control subjects. Furthermore, neuropathic pain patients had a localized hypersensitivity to mechanical and thermal stimuli in the affected area of the body. In contrast, fibromyalgia patients displayed a general hypersensitivity to mechanical and thermal stimuli when the stimuli were rated by the VAS, and hypersensitivity to some of the sensory stimuli. Conclusions These findings are the first to suggest that a conditioning stimulus evoked by a cold pressor test reduced spontaneous ongoing pain in patients with peripheral neuropathic pain, but not in fibromyalgia patients when directly compared. The current study supports the notion that fibromyalgia and neuropathic pain are distinct pain conditions with separate sensory patterns and dysfunctions in pain-modulating networks. Fibromyalgia should therefore not, as sometimes discussed, be included in NP conditions. Implications On the basis of the findings, it is of interest to speculate on the underlying mechanisms. The results are consistent with the idea that peripheral neuropathic pain is primarily driven from damaged nerve endings in the periphery, while chronic fibromyalgia pain may be a central disorder with increased activity in pain-facilitating systems.

Microbial contamination of mobile phones in a health care setting in Alexandria, Egypt.

PubMed

Selim, Heba Sayed; Abaza, Amani Farouk

2015-01-01

This study aimed at investigating the microbial contamination of mobile phones in a hospital setting. Swab samples were collected from 40 mobile phones of patients and health care workers at the Alexandria University Students' Hospital. They were tested for their bacterial contamination at the microbiology laboratory of the High Institute of Public Health. Quantification of bacteria was performed using both surface spread and pour plate methods. Isolated bacterial agents were identified using standard microbiological methods. Methicillin-resistant Staphylococcus aureus was identified by disk diffusion method described by Bauer and Kirby. Isolated Gram-negative bacilli were tested for being extended spectrum beta lactamase producers using the double disk diffusion method according to the Clinical and Laboratory Standards Institute recommendations. All of the tested mobile phones (100%) were contaminated with either single or mixed bacterial agents. The most prevalent bacterial contaminants were methicillin-resistant S. aureus and coagulase-negative staphylococci representing 53% and 50%, respectively. The mean bacterial count was 357 CFU/ml, while the median was 13 CFU/ml using the pour plate method. The corresponding figures were 2,192 and 1,720 organisms/phone using the surface spread method. Mobile phones usage in hospital settings poses a risk of transmission of a variety of bacterial agents including multidrug-resistant pathogens as methicillin-resistant S. aureus. The surface spread method is an easy and useful tool for detection and estimation of bacterial contamination of mobile phones.

Microbial contamination of mobile phones in a health care setting in Alexandria, Egypt

PubMed Central

Selim, Heba Sayed; Abaza, Amani Farouk

2015-01-01

Aim: This study aimed at investigating the microbial contamination of mobile phones in a hospital setting. Methods: Swab samples were collected from 40 mobile phones of patients and health care workers at the Alexandria University Students’ Hospital. They were tested for their bacterial contamination at the microbiology laboratory of the High Institute of Public Health. Quantification of bacteria was performed using both surface spread and pour plate methods. Isolated bacterial agents were identified using standard microbiological methods. Methicillin-resistant Staphylococcus aureus was identified by disk diffusion method described by Bauer and Kirby. Isolated Gram-negative bacilli were tested for being extended spectrum beta lactamase producers using the double disk diffusion method according to the Clinical and Laboratory Standards Institute recommendations. Results: All of the tested mobile phones (100%) were contaminated with either single or mixed bacterial agents. The most prevalent bacterial contaminants were methicillin-resistant S. aureus and coagulase-negative staphylococci representing 53% and 50%, respectively. The mean bacterial count was 357 CFU/ml, while the median was 13 CFU/ml using the pour plate method. The corresponding figures were 2,192 and 1,720 organisms/phone using the surface spread method. Conclusions: Mobile phones usage in hospital settings poses a risk of transmission of a variety of bacterial agents including multidrug-resistant pathogens as methicillin-resistant S. aureus. The surface spread method is an easy and useful tool for detection and estimation of bacterial contamination of mobile phones. PMID:25699226

The 400W at 1.8K Test Facility at CEA-Grenoble

NASA Astrophysics Data System (ADS)

Roussel, P.; Girard, A.; Jager, B.; Rousset, B.; Bonnay, P.; Millet, F.; Gully, P.

2006-04-01

A new test facility with a cooling capacity respectively of 400W at 1.8K or 800W at 4.5K, is now under nominal operation in SBT (Low Temperature Department) at CEA Grenoble. It has been recently used for thermohydraulic studies of two phase superfluid helium in autumn 2004. In the near future, this test bench will allow: - to test industrial components at 1.8K (magnets, cavities of accelerators) - to continue the present studies on thermohydraulics of two phase superfluid helium - to develop and simulate new cooling loops for ITER Cryogenics, and other applications such as high Reynolds number flows This new facility consists of a cold box connected to a warm compressor station (one subatmospheric oil ring pump in series with two screw compressors). The cold box, designed by AIR LIQUIDE, comprises two centrifugal cold compressors, a cold turbine, a wet piston expander, counter flow heat exchangers and two phase separators at 4.5K and 1.8K. The new facility uses a Programmable Logic Controller (PLC) connected to a bus for the measurements. The design is modular and will allow the use of saturated fluid flow (two phase flow at 1.8K or 4.5K) or single phase fluid forced flow. Experimental results and cooling capacity in different operation modes are detailed.

An In vitro Comparison and Evaluation of Sealing Ability of Newly Introduced C-point System, Cold Lateral Condensation, and Thermoplasticized Gutta-Percha Obturating Technique: A Dye Extraction Study.

PubMed

Sinhal, Tapati Manohar; Shah, Ruchi Rani Purvesh; Jais, Pratik Subhas; Shah, Nimisha Chinmay; Hadwani, Krupali Dhirubhai; Rothe, Tushar; Sinhal, Neha Nilesh

2018-01-01

The aim of this study is to compare and to evaluate sealing ability of newly introduced C-point system, cold lateral condensation, and thermoplasticized gutta-percha obturating technique using a dye extraction method. Sixty extracted maxillary central incisors were decoronated below the cementoenamel junction. Working length was established, and biomechanical preparation was done using K3 rotary files with standard irrigation protocol. Teeth were divided into three groups according to the obturation protocol; Group I-Cold lateral condensation, Group II-Thermoplasticized gutta-percha, and Group III-C-Point obturating system. After obturation all samples were subjected to microleakage assessment using dye extraction method. Obtained scores will be statistical analyzed using ANOVA test and post hoc Tukey's test. One-way analysis of variance revealed that there is significant difference among the three groups with P value (0.000 < 0.05). Tukey's HSD post hoc tests for multiple comparisons test shows that the Group II and III perform significantly better than Group I. Group III performs better than Group II with no significant difference. All the obturating technique showed some degree of microleakage. Root canals filled with C-point system showed least microleakage followed by thermoplasticized obturating technique with no significant difference among them. C-point obturation system could be an alternative to the cold lateral condensation technique.