Application of Decision Tree on Collision Avoidance System Design and Verification for Quadcopter

NASA Astrophysics Data System (ADS)

Chen, C.-W.; Hsieh, P.-H.; Lai, W.-H.

2017-08-01

The purpose of the research is to build a collision avoidance system with decision tree algorithm used for quadcopters. While the ultrasonic range finder judges the distance is in collision avoidance interval, the access will be replaced from operator to the system to control the altitude of the UAV. According to the former experiences on operating quadcopters, we can obtain the appropriate pitch angle. The UAS implement the following three motions to avoid collisions. Case1: initial slow avoidance stage, Case2: slow avoidance stage and Case3: Rapid avoidance stage. Then the training data of collision avoidance test will be transmitted to the ground station via wireless transmission module to further analysis. The entire decision tree algorithm of collision avoidance system, transmission data, and ground station have been verified in some flight tests. In the flight test, the quadcopter can implement avoidance motion in real-time and move away from obstacles steadily. In the avoidance area, the authority of the collision avoidance system is higher than the operator and implements the avoidance process. The quadcopter can successfully fly away from the obstacles in 1.92 meter per second and the minimum distance between the quadcopter and the obstacle is 1.05 meters.

Airborne Collision Detection and Avoidance for Small UAS Sense and Avoid Systems

NASA Astrophysics Data System (ADS)

Sahawneh, Laith Rasmi

The increasing demand to integrate unmanned aircraft systems (UAS) into the national airspace is motivated by the rapid growth of the UAS industry, especially small UAS weighing less than 55 pounds. Their use however has been limited by the Federal Aviation Administration regulations due to collision risk they pose, safety and regulatory concerns. Therefore, before civil aviation authorities can approve routine UAS flight operations, UAS must be equipped with sense-and-avoid technology comparable to the see-and-avoid requirements for manned aircraft. The sense-and-avoid problem includes several important aspects including regulatory and system-level requirements, design specifications and performance standards, intruder detecting and tracking, collision risk assessment, and finally path planning and collision avoidance. In this dissertation, our primary focus is on developing an collision detection, risk assessment and avoidance framework that is computationally affordable and suitable to run on-board small UAS. To begin with, we address the minimum sensing range for the sense-and-avoid (SAA) system. We present an approximate close form analytical solution to compute the minimum sensing range to safely avoid an imminent collision. The approach is then demonstrated using a radar sensor prototype that achieves the required minimum sensing range. In the area of collision risk assessment and collision prediction, we present two approaches to estimate the collision risk of an encounter scenario. The first is a deterministic approach similar to those been developed for Traffic Alert and Collision Avoidance (TCAS) in manned aviation. We extend the approach to account for uncertainties of state estimates by deriving an analytic expression to propagate the error variance using Taylor series approximation. To address unanticipated intruders maneuvers, we propose an innovative probabilistic approach to quantify likely intruder trajectories and estimate the probability of collision risk using the uncorrelated encounter model (UEM) developed by MIT Lincoln Laboratory. We evaluate the proposed approach using Monte Carlo simulations and compare the performance with linearly extrapolated collision detection logic. For the path planning and collision avoidance part, we present multiple reactive path planning algorithms. We first propose a collision avoidance algorithm based on a simulated chain that responds to a virtual force field produced by encountering intruders. The key feature of the proposed approach is to model the future motion of both the intruder and the ownship using a chain of waypoints that are equally spaced in time. This timing information is used to continuously re-plan paths that minimize the probability of collision. Second, we present an innovative collision avoidance logic using an ownship centered coordinate system. The technique builds a graph in the local-level frame and uses the Dijkstra's algorithm to find the least cost path. An advantage of this approach is that collision avoidance is inherently a local phenomenon and can be more naturally represented in the local coordinates than the global coordinates. Finally, we propose a two step path planner for ground-based SAA systems. In the first step, an initial suboptimal path is generated using A* search. In the second step, using the A* solution as an initial condition, a chain of unit masses connected by springs and dampers evolves in a simulated force field. The chain is described by a set of ordinary differential equations that is driven by virtual forces to find the steady-state equilibrium. The simulation results show that the proposed approach produces collision-free plans while minimizing the path length. To move towards a deployable system, we apply collision detection and avoidance techniques to a variety of simulation and sensor modalities including camera, radar and ADS-B along with suitable tracking schemes. Keywords: unmanned aircraft system, small UAS, sense and avoid, minimum sensing range, airborne collision detection and avoidance, collision detection, collision risk assessment, collision avoidance, conflict detection, conflict avoidance, path planning.

Auditory displays as occasion setters.

PubMed

Mckeown, Denis; Isherwood, Sarah; Conway, Gareth

2010-02-01

The aim of this study was to evaluate whether representational sounds that capture the richness of experience of a collision enhance performance in braking to avoid a collision relative to other forms of warnings in a driving simulator. There is increasing interest in auditory warnings that are informative about their referents. But as well as providing information about some intended object, warnings may be designed to set the occasion for a rich body of information about the outcomes of behavior in a particular context. These richly informative warnings may offer performance advantages, as they may be rapidly processed by users. An auditory occasion setter for a collision (a recording of screeching brakes indicating imminent collision) was compared with two other auditory warnings (an abstract and an "environmental" sound), a speech message, a visual display, and no warning in a fixed-base driving simulator as interfaces to a collision avoidance system. The main measure was braking response times at each of two headways (1.5 s and 3 s) to a lead vehicle. The occasion setter demonstrated statistically significantly faster braking responses at each headway in 8 out of 10 comparisons (with braking responses equally fast to the abstract warning at 1.5 s and the environmental warning at 3 s). Auditory displays that set the occasion for an outcome in a particular setting and for particular behaviors may offer small but critical performance enhancements in time-critical applications. The occasion setter could be applied in settings where speed of response by users is of the essence.

14 CFR 437.65 - Collision avoidance analysis.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Collision avoidance analysis. 437.65... analysis. (a) For a permitted flight with a planned maximum altitude greater than 150 kilometers, a permittee must obtain a collision avoidance analysis from United States Strategic Command. (b) The collision...

Development of collision avoidance system for useful UAV applications using image sensors with laser transmitter

NASA Astrophysics Data System (ADS)

Cheong, M. K.; Bahiki, M. R.; Azrad, S.

2016-10-01

The main goal of this study is to demonstrate the approach of achieving collision avoidance on Quadrotor Unmanned Aerial Vehicle (QUAV) using image sensors with colour- based tracking method. A pair of high definition (HD) stereo cameras were chosen as the stereo vision sensor to obtain depth data from flat object surfaces. Laser transmitter was utilized to project high contrast tracking spot for depth calculation using common triangulation. Stereo vision algorithm was developed to acquire the distance from tracked point to QUAV and the control algorithm was designed to manipulate QUAV's response based on depth calculated. Attitude and position controller were designed using the non-linear model with the help of Optitrack motion tracking system. A number of collision avoidance flight tests were carried out to validate the performance of the stereo vision and control algorithm based on image sensors. In the results, the UAV was able to hover with fairly good accuracy in both static and dynamic collision avoidance for short range collision avoidance. Collision avoidance performance of the UAV was better with obstacle of dull surfaces in comparison to shiny surfaces. The minimum collision avoidance distance achievable was 0.4 m. The approach was suitable to be applied in short range collision avoidance.

Strategies for Pre-Emptive Mid-Air Collision Avoidance in Budgerigars

PubMed Central

Schiffner, Ingo; Srinivasan, Mandyam V.

2016-01-01

We have investigated how birds avoid mid-air collisions during head-on encounters. Trajectories of birds flying towards each other in a tunnel were recorded using high speed video cameras. Analysis and modelling of the data suggest two simple strategies for collision avoidance: (a) each bird veers to its right and (b) each bird changes its altitude relative to the other bird according to a preset preference. Both strategies suggest simple rules by which collisions can be avoided in head-on encounters by two agents, be they animals or machines. The findings are potentially applicable to the design of guidance algorithms for automated collision avoidance on aircraft. PMID:27680488

2002 Defense Modeling and Simulation Office (DMSO) Laboratory for Human Behavior Model Interchange Standards

DTIC Science & Technology

2003-07-01

standard release with the publicly available "mod" interface allows us to avoid purchasing a game engine license (approximate cost $350,000) from Epic...depletion is accurately simulated for ammunition * Both contain target detection, target identification, target selection, and collision avoidance and...into other game genres such as Real-Time Strategy (RTS) games and Massively Multiplayer Online Role- Playing Games ( MMORPG ). Unfortunately these game

Decision Support from Genetic Algorithms for Ship Collision Avoidance Route Planning and Alerts

NASA Astrophysics Data System (ADS)

Tsou, Ming-Cheng; Kao, Sheng-Long; Su, Chien-Min

When an officer of the watch (OOW) faces complicated marine traffic, a suitable decision support tool could be employed in support of collision avoidance decisions, to reduce the burden and greatly improve the safety of marine traffic. Decisions on routes to avoid collisions could also consider economy as well as safety. Through simulating the biological evolution model, this research adopts the genetic algorithm used in artificial intelligence to find a theoretically safety-critical recommendation for the shortest route of collision avoidance from an economic viewpoint, combining the international regulations for preventing collisions at sea (COLREGS) and the safety domain of a ship. Based on this recommendation, an optimal safe avoidance turning angle, navigation restoration time and navigational restoration angle will also be provided. A Geographic Information System (GIS) will be used as the platform for display and operation. In order to achieve advance notice of alerts and due preparation for collision avoidance, a Vessel Traffic Services (VTS) operator and the OOW can use this system as a reference to assess collision avoidance at present location.

Ensuring Interoperability between UAS Detect-and-Avoid and Manned Aircraft Collision Avoidance

NASA Technical Reports Server (NTRS)

Thipphavong, David; Cone, Andrew; Lee, Seung Man; Santiago, Confesor

2017-01-01

The UAS community in the United States has identified the need for a collision avoidance region in which UAS Detect-and-Avoid (DAA) vertical guidance is restricted to preclude interoperability issues with manned aircraft collision avoidance system vertical resolution advisories (RAs). This paper documents the process by which the collision avoidance region was defined. Three candidate definitions were evaluated on 1.3 million simulated pairwise encounters between UAS and manned aircraft covering a wide range of horizontal and vertical closure rates, angles, and miss distances. They were evaluated with regard to UAS DAA interoperability with manned aircraft collision avoidance systems in terms of: 1) the primary objective of restricting DAA vertical guidance before RAs when the aircraft are close, and 2) the secondary objective of avoiding unnecessary restrictions of DAA vertical guidance at a DAA alert when the aircraft are further apart. The collision avoidance region definition that fully achieves the primary objective and best achieves the secondary objective was recommended to and accepted by the UAS community in the United States. By this definition, UAS and manned aircraft are in the collision avoidance region--during which DAA vertical guidance is restricted--when the time to closest point of approach is less than 50 seconds and either the time to co-altitude is less than 50 seconds or the current vertical separation is less than 800 feet.

Ensuring Interoperability Between Unmanned Aircraft Detect-and-Avoid and Manned Aircraft Collision Avoidance

NASA Technical Reports Server (NTRS)

Thipphavong, David; Cone, Andrew; Lee, Seungman

2017-01-01

The Unmanned Aircraft Systems (UAS) community in the United States has identified the need for a collision avoidance region in which UAS Detect-and-Avoid (DAA) vertical guidance is restricted to preclude interoperability issues with manned aircraft collision avoidance system vertical resolution advisories (RAs). This paper documents the process by which the collision avoidance region was defined. Three candidate definitions were evaluated on 1.3 million simulated pairwise encounters between UAS and manned aircraft covering a wide range of horizontal and vertical closure rates, angles, and miss distances. Each definition was evaluated with regard to UAS DAA interoperability with manned aircraft collision avoidance in terms of how well it achieved: 1) the primary objective of restricting DAA vertical guidance prior to RAs when the aircraft are close, and 2) the secondary objective of avoiding unnecessary restrictions of DAA vertical guidance at DAA alerts when the aircraft are further apart. The collision avoidance region definition that fully achieves the primary objective and best achieves the secondary objective was recommended to and accepted by the UAS community in the United States. By this definition, UAS and manned aircraft are in the collision avoidance region where DAA vertical guidance is restricted when the time to closest point of approach (CPA) is less than 50 seconds and either the time to co-altitude is less than 50 seconds or the current vertical separation is less than 800 feet.

Collision-free motion of two robot arms in a common workspace

NASA Technical Reports Server (NTRS)

Basta, Robert A.; Mehrotra, Rajiv; Varanasi, Murali R.

1987-01-01

Collision-free motion of two robot arms in a common workspace is investigated. A collision-free motion is obtained by detecting collisions along the preplanned trajectories using a sphere model for the wrist of each robot and then modifying the paths and/or trajectories of one or both robots to avoid the collision. Detecting and avoiding collisions are based on the premise that: preplanned trajectories of the robots follow a straight line; collisions are restricted to between the wrists of the two robots (which corresponds to the upper three links of PUMA manipulators); and collisions never occur between the beginning points or end points on the straight line paths. The collision detection algorithm is described and some approaches to collision avoidance are discussed.

USA Space Debris Environment, Operations, and Research Updates

NASA Technical Reports Server (NTRS)

Liou, J.-C.

2018-01-01

Space Missions in 2017 Earth Satellite Population Collision Avoidance Maneuvers Post mission Disposal of U.S.A. Spacecraft Space Situational Awareness (SSA) and the Space Debris Sensor (SDS) A total of 86 space launches placed more than 400 spacecraft into Earth orbits during 2017, following the trend of increase over the past decade NASA has established conjunction assessment processes for its human spaceflight and uncrewed spacecraft to avoid accidental collisions with objects tracked by the U.S. Space Surveillance Network - NASA also assists other U.S. government spacecraft owners with conjunction assessments and subsequent maneuvers The ISS has conducted 25 debris collision avoidance maneuvers since 1999 - None in 2016-2017, but an ISS visiting vehicle had one collision avoidance maneuver in 2017 During 2017 NASA executed or assisted in the execution of 21 collision avoidance maneuvers by uncrewed spacecraft - Four maneuvers were conducted to avoid debris from Fengyun-1C - Two maneuvers were conducted to avoid debris from the collision of Cosmos 2251 and Iridium 33 - One maneuver was conducted to avoid the ISS NASA has established conjunction assessment processes for its human spaceflight and uncrewed spacecraft to avoid accidental collisions with objects tracked by the U.S. Space Surveillance Network - NASA also assists other U.S. government spacecraft owners with conjunction assessments and subsequent maneuvers The ISS has conducted 25 debris collision avoidance maneuvers since 1999 - None in 2016-2017, but an ISS visiting vehicle had one collision avoidance maneuver in 2017 During 2017 NASA executed or assisted in the execution of 21 collision avoidance maneuvers by uncrewed spacecraft - Four maneuvers were conducted to avoid debris from Fengyun-1C - Two maneuvers were conducted to avoid debris from the collision of Cosmos 2251 and Iridium 33 The 2014-15 NASA Engineering and Safety Center (NESC) study on the micrometeoroid and orbital debris (MMOD) assessment for the Joint Polar Satellite System (JPSS) provided the following findings - Millimeter-sized orbital debris pose the highest penetration risk to most operational spacecraft in LEO - The most effective means to collect direct measurement data on millimetersized debris above 600 km altitude is to conduct in situ measurements - There is currently no in situ data on such small debris above 600 km altitude Since the orbital debris population follows a power-law size distribution, there are many more millimeter-sized debris than the large tracked objects - Current conjunction assessments and collision avoidance maneuvers against the tracked objects (which are typically 10 cm and larger) only address a small fraction (<1%) of the mission-ending risk from orbital debris To address the millimeter-sized debris data gap above 600 km, NASA has recently developed an innovative in situ measurement instrument - the Space Debris Sensor (SDS) - One maneuver was conducted to avoid the ISS

Intersection collision avoidance using ITS countermeasures. Task 9, Intersection collision avoidance system performance guidelines

DOT National Transportation Integrated Search

2000-09-01

Phase III of the Intersection Collision Avoidance Using ITS Countermeasures program developed testbed systems, implemented the systems on a vehicle, and performed testing to determine the potential effectiveness of this system in preventing intersect...

Effective dynamical coupling of hydrodynamics and transport for heavy-ion collisions

NASA Astrophysics Data System (ADS)

Oliinychenko, Dmytro; Petersen, Hannah

2017-04-01

Present hydrodynamics-based simulations of heavy-ion collisions neglect the feedback from the frozen-out particles flying back into the hydrodynamical region. This causes an artefact called “negative Cooper-Frye contributions”, which is negligible for high collision energies, but becomes significant for lower RHIC BES energies and for event-by-event simulations. To avoid negative Cooper-Frye contributions, while still preserving hydrodynamical behavior, we propose a pure hadronic transport approach with forced thermalization in the regions of high energy density. It is demonstrated that this approach exhibits enhancement of strangeness and mean transverse momenta compared to conventional transport - an effect typical for hydrodynamical approaches.

Braking Analysis For Collision Avoidance-- Autonomous Braking System Performance Modeling And Benefits Analysis

DOT National Transportation Integrated Search

1996-05-24

THIS REPORT IS AN ANALYSIS OF THE BENEFITS OF A COLLISION AVOIDANCE SYSTEM IN REDUCING REAR-END CRASHES. THE COLLISION AVOIDANCE SYSTEM CONSIDERED IN THIS STUDY UTILIZES THE SIGNAL FROM A FORWARD LOOKING SENSOR TO ACTIVATE THE TRACTION CONTROL VALVE ...

76 FR 62321 - Airworthiness Directives; Aviation Communication & Surveillance Systems (ACSS) Traffic Alert and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... Communication & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance System (TCAS) Units AGENCY... certain Aviation Communication & Surveillance Systems (ACSS) traffic alert and collision avoidance system...) traffic alert and collision avoidance system (TCAS) units with part numbers identified in ACSS Technical...

75 FR 81512 - Airworthiness Directives; Various Aviation Communication & Surveillance Systems (ACSS) Traffic...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... Communication & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance System (TCAS) Units AGENCY... & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance System (TCAS) units during a flight test over... applies to Aviation Communication & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance...

Safety of high-speed guided ground transportation systems : collision avoidance and accident survivability : volume 2 : collision avoidance

DOT National Transportation Integrated Search

1993-03-01

This report is the second of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is t...

Formation flight and collision avoidance for multiple UAVs based on modified tentacle algorithm in unstructured environments

PubMed Central

2017-01-01

This paper presents a method for formation flight and collision avoidance of multiple UAVs. Due to the shortcomings such as collision avoidance caused by UAV’s high-speed and unstructured environments, this paper proposes a modified tentacle algorithm to ensure the high performance of collision avoidance. Different from the conventional tentacle algorithm which uses inverse derivation, the modified tentacle algorithm rapidly matches the radius of each tentacle and the steering command, ensuring that the data calculation problem in the conventional tentacle algorithm is solved. Meanwhile, both the speed sets and tentacles in one speed set are reduced and reconstructed so as to be applied to multiple UAVs. Instead of path iterative optimization, the paper selects the best tentacle to obtain the UAV collision avoidance path quickly. The simulation results show that the method presented in the paper effectively enhances the performance of flight formation and collision avoidance for multiple high-speed UAVs in unstructured environments. PMID:28763498

Automatic Collision Avoidance Technology (ACAT)

NASA Technical Reports Server (NTRS)

Swihart, Donald E.; Skoog, Mark A.

2007-01-01

This document represents two views of the Automatic Collision Avoidance Technology (ACAT). One viewgraph presentation reviews the development and system design of Automatic Collision Avoidance Technology (ACAT). Two types of ACAT exist: Automatic Ground Collision Avoidance (AGCAS) and Automatic Air Collision Avoidance (AACAS). The AGCAS Uses Digital Terrain Elevation Data (DTED) for mapping functions, and uses Navigation data to place aircraft on map. It then scans DTED in front of and around aircraft and uses future aircraft trajectory (5g) to provide automatic flyup maneuver when required. The AACAS uses data link to determine position and closing rate. It contains several canned maneuvers to avoid collision. Automatic maneuvers can occur at last instant and both aircraft maneuver when using data link. The system can use sensor in place of data link. The second viewgraph presentation reviews the development of a flight test and an evaluation of the test. A review of the operation and comparison of the AGCAS and a pilot's performance are given. The same review is given for the AACAS is given.

Development Of Performance Specifications For Collision Avoidance Systems For Lane Change, Merging, And Backing, Task 3 - Interim Report: Test Of Existing Hardware

DOT National Transportation Integrated Search

1995-05-01

KEYWORDS : ADVANCED VEHICLE CONTROL & SAFETY SYSTEMS OR AVCSS, COLLISION WARNING/AVOIDANCE SYSTEMS, CRASH REDUCTION, INTELLIGENT VEHICLE INITIATIVE OR IVI : RESULTS FROM THE TESTING OF ELEVEN COLLISION AVOIDANCE SYSTEMS (CAS) FOR LANE CHANGE, ...

Intelligent Local Avoided Collision (iLAC) MAC Protocol for Very High Speed Wireless Network

NASA Astrophysics Data System (ADS)

Hieu, Dinh Chi; Masuda, Akeo; Rabarijaona, Verotiana Hanitriniala; Shimamoto, Shigeru

Future wireless communication systems aim at very high data rates. As the medium access control (MAC) protocol plays the central role in determining the overall performance of the wireless system, designing a suitable MAC protocol is critical to fully exploit the benefit of high speed transmission that the physical layer (PHY) offers. In the latest 802.11n standard [2], the problem of long overhead has been addressed adequately but the issue of excessive colliding transmissions, especially in congested situation, remains untouched. The procedure of setting the backoff value is the heart of the 802.11 distributed coordination function (DCF) to avoid collision in which each station makes its own decision on how to avoid collision in the next transmission. However, collision avoidance is a problem that can not be solved by a single station. In this paper, we introduce a new MAC protocol called Intelligent Local Avoided Collision (iLAC) that redefines individual rationality in choosing the backoff counter value to avoid a colliding transmission. The distinguishing feature of iLAC is that it fundamentally changes this decision making process from collision avoidance to collaborative collision prevention. As a result, stations can avoid colliding transmissions with much greater precision. Analytical solution confirms the validity of this proposal and simulation results show that the proposed algorithm outperforms the conventional algorithms by a large margin.

78 FR 61445 - Seventy-Sixth Meeting: RTCA Special Committee 147, Minimum Operational Performance Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-03

... Committee 147, Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... Traffic Alert and Collision Avoidance Systems Airborne Equipment. SUMMARY: The FAA is issuing this notice... Performance Standards for Traffic Alert and Collision Avoidance Systems Airborne Equipment. DATES: The meeting...

78 FR 66419 - Seventy Sixth Meeting: RTCA Special Committee 147, Minimum Operational Performance Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-05

... Committee 147, Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... Traffic Alert and Collision Avoidance Systems Airborne Equipment. SUMMARY: The FAA is issuing this notice... Performance Standards for Traffic Alert and Collision Avoidance Systems Airborne Equipment. DATES: The meeting...

77 FR 29749 - 74th Meeting: RTCA Special Committee 147, Minimal Operations Performance Standards for Traffic...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-18

... 147, Minimal Operations Performance Standards for Traffic Alert and Collision Avoidance Systems... Traffic Alert and Collision Avoidance Systems Airborne Equipment. SUMMARY: The FAA is issuing this notice... Performance Standards for Traffic Alert and Collision Avoidance Systems Airborne Equipment. DATES: The meeting...

78 FR 6401 - Seventy Fifth Meeting: RTCA Special Committee 147, Minimum Operational Performance Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-30

... Committee 147, Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... Traffic Alert and Collision Avoidance Systems Airborne Equipment. SUMMARY: The FAA is issuing this notice... Performance Standards for Traffic Alert and Collision Avoidance Systems Airborne Equipment. DATES: The meeting...

Multi-actuators vehicle collision avoidance system - Experimental validation

NASA Astrophysics Data System (ADS)

Hamid, Umar Zakir Abdul; Zakuan, Fakhrul Razi Ahmad; Akmal Zulkepli, Khairul; Zulfaqar Azmi, Muhammad; Zamzuri, Hairi; Rahman, Mohd Azizi Abdul; Aizzat Zakaria, Muhammad

2018-04-01

The Insurance Institute for Highway Safety (IIHS) of the United States of America in their reports has mentioned that a significant amount of the road mishaps would be preventable if more automated active safety applications are adopted into the vehicle. This includes the incorporation of collision avoidance system. The autonomous intervention by the active steering and braking systems in the hazardous scenario can aid the driver in mitigating the collisions. In this work, a real-time platform of a multi-actuators vehicle collision avoidance system is developed. It is a continuous research scheme to develop a fully autonomous vehicle in Malaysia. The vehicle is a modular platform which can be utilized for different research purposes and is denominated as Intelligent Drive Project (iDrive). The vehicle collision avoidance proposed design is validated in a controlled environment, where the coupled longitudinal and lateral motion control system is expected to provide desired braking and steering actuation in the occurrence of a frontal static obstacle. Results indicate the ability of the platform to yield multi-actuators collision avoidance navigation in the hazardous scenario, thus avoiding the obstacle. The findings of this work are beneficial for the development of a more complex and nonlinear real-time collision avoidance work in the future.

Dynamic Obstacle Avoidance for Unmanned Underwater Vehicles Based on an Improved Velocity Obstacle Method

PubMed Central

Zhang, Wei; Wei, Shilin; Teng, Yanbin; Zhang, Jianku; Wang, Xiufang; Yan, Zheping

2017-01-01

In view of a dynamic obstacle environment with motion uncertainty, we present a dynamic collision avoidance method based on the collision risk assessment and improved velocity obstacle method. First, through the fusion optimization of forward-looking sonar data, the redundancy of the data is reduced and the position, size and velocity information of the obstacles are obtained, which can provide an accurate decision-making basis for next-step collision avoidance. Second, according to minimum meeting time and the minimum distance between the obstacle and unmanned underwater vehicle (UUV), this paper establishes the collision risk assessment model, and screens key obstacles to avoid collision. Finally, the optimization objective function is established based on the improved velocity obstacle method, and a UUV motion characteristic is used to calculate the reachable velocity sets. The optimal collision speed of UUV is searched in velocity space. The corresponding heading and speed commands are calculated, and outputted to the motion control module. The above is the complete dynamic obstacle avoidance process. The simulation results show that the proposed method can obtain a better collision avoidance effect in the dynamic environment, and has good adaptability to the unknown dynamic environment. PMID:29186878

GNSS/Electronic Compass/Road Segment Information Fusion for Vehicle-to-Vehicle Collision Avoidance Application

PubMed Central

Cheng, Qi; Xue, Dabin; Wang, Guanyu; Ochieng, Washington Yotto

2017-01-01

The increasing number of vehicles in modern cities brings the problem of increasing crashes. One of the applications or services of Intelligent Transportation Systems (ITS) conceived to improve safety and reduce congestion is collision avoidance. This safety critical application requires sub-meter level vehicle state estimation accuracy with very high integrity, continuity and availability, to detect an impending collision and issue a warning or intervene in the case that the warning is not heeded. Because of the challenging city environment, to date there is no approved method capable of delivering this high level of performance in vehicle state estimation. In particular, the current Global Navigation Satellite System (GNSS) based collision avoidance systems have the major limitation that the real-time accuracy of dynamic state estimation deteriorates during abrupt acceleration and deceleration situations, compromising the integrity of collision avoidance. Therefore, to provide the Required Navigation Performance (RNP) for collision avoidance, this paper proposes a novel Particle Filter (PF) based model for the integration or fusion of real-time kinematic (RTK) GNSS position solutions with electronic compass and road segment data used in conjunction with an Autoregressive (AR) motion model. The real-time vehicle state estimates are used together with distance based collision avoidance algorithms to predict potential collisions. The algorithms are tested by simulation and in the field representing a low density urban environment. The results show that the proposed algorithm meets the horizontal positioning accuracy requirement for collision avoidance and is superior to positioning accuracy of GNSS only, traditional Constant Velocity (CV) and Constant Acceleration (CA) based motion models, with a significant improvement in the prediction accuracy of potential collision. PMID:29186851

GNSS/Electronic Compass/Road Segment Information Fusion for Vehicle-to-Vehicle Collision Avoidance Application.

PubMed

Sun, Rui; Cheng, Qi; Xue, Dabin; Wang, Guanyu; Ochieng, Washington Yotto

2017-11-25

The increasing number of vehicles in modern cities brings the problem of increasing crashes. One of the applications or services of Intelligent Transportation Systems (ITS) conceived to improve safety and reduce congestion is collision avoidance. This safety critical application requires sub-meter level vehicle state estimation accuracy with very high integrity, continuity and availability, to detect an impending collision and issue a warning or intervene in the case that the warning is not heeded. Because of the challenging city environment, to date there is no approved method capable of delivering this high level of performance in vehicle state estimation. In particular, the current Global Navigation Satellite System (GNSS) based collision avoidance systems have the major limitation that the real-time accuracy of dynamic state estimation deteriorates during abrupt acceleration and deceleration situations, compromising the integrity of collision avoidance. Therefore, to provide the Required Navigation Performance (RNP) for collision avoidance, this paper proposes a novel Particle Filter (PF) based model for the integration or fusion of real-time kinematic (RTK) GNSS position solutions with electronic compass and road segment data used in conjunction with an Autoregressive (AR) motion model. The real-time vehicle state estimates are used together with distance based collision avoidance algorithms to predict potential collisions. The algorithms are tested by simulation and in the field representing a low density urban environment. The results show that the proposed algorithm meets the horizontal positioning accuracy requirement for collision avoidance and is superior to positioning accuracy of GNSS only, traditional Constant Velocity (CV) and Constant Acceleration (CA) based motion models, with a significant improvement in the prediction accuracy of potential collision.

Power mobility with collision avoidance for older adults: user, caregiver, and prescriber perspectives.

PubMed

Wang, Rosalie H; Korotchenko, Alexandra; Hurd Clarke, Laura; Mortenson, W Ben; Mihailidis, Alex

2013-01-01

Collision avoidance technology has the capacity to facilitate safer mobility among older power mobility users with physical, sensory, and cognitive impairments, thus enabling independence for more users. Little is known about consumers' perceptions of collision avoidance. This article draws on interviews (29 users, 5 caregivers, and 10 prescribers) to examine views on design and utilization of this technology. Data analysis identified three themes: "useful situations or contexts," "technology design issues and real-life application," and "appropriateness of collision avoidance technology for a variety of users." Findings support ongoing development of collision avoidance for older adult users. The majority of participants supported the technology and felt that it might benefit current users and users with visual impairments, but might be unsuitable for people with significant cognitive impairments. Some participants voiced concerns regarding the risk for injury with power mobility use and some identified situations where collision avoidance might be beneficial (driving backward, avoiding dynamic obstacles, negotiating outdoor barriers, and learning power mobility use). Design issues include the need for context awareness, reliability, and user interface specifications. User desire to maintain driving autonomy supports development of collaboratively controlled systems. This research lays the groundwork for future development by illustrating consumer requirements for this technology.

Design study of general aviation collision avoidance system

NASA Technical Reports Server (NTRS)

Bates, M. R.; Moore, L. D.; Scott, W. V.

1972-01-01

The selection and design of a time/frequency collision avoidance system for use in general aviation aircraft is discussed. The modifications to airline transport collision avoidance equipment which were made to produce the simpler general aviation system are described. The threat determination capabilities and operating principles of the general aviation system are illustrated.

Cooperative Collision Avoidance Step 1 - Technology Demonstration Flight Test Report. Revision 1

NASA Technical Reports Server (NTRS)

Trongale, Nicholas A.

2006-01-01

The National Aeronautics and Space Administration (NASA) Access 5 Project Office sponsored a cooperative collision avoidance flight demonstration program for unmanned aircraft systems (UAS). This flight test was accomplished between September 21st and September 27th 2005 from the Mojave Airport, Mojave, California. The objective of these flights was to collect data for the Access 5 Cooperative Collision Avoidance (CCA) Work Package simulation effort, i.e., to gather data under select conditions to allow validation of the CCA simulation. Subsequent simulation to be verified were: Demonstrate the ability to detect cooperative traffic and provide situational awareness to the ROA pilot; Demonstrate the ability to track the detected cooperative traffic and provide position information to the ROA pilot; Demonstrate the ability to determine collision potential with detected cooperative traffic and provide notification to the ROA pilot; Demonstrate that the CCA subsystem provides information in sufficient time for the ROA pilot to initiate an evasive maneuver to avoid collision; Demonstrate an evasive maneuver that avoids collision with the threat aircraft; and lastly, Demonstrate the ability to assess the adequacy of the maneuver and determine that the collision potential has been avoided. The Scaled Composites, LLC Proteus Optionally Piloted Vehicle (OPV) was chosen as the test platform. Proteus was manned by two on-board pilots but was also capable of being controlled from an Air Vehicle Control Station (AVCS) located on the ground. For this demonstration, Proteus was equipped with cooperative collision sensors and the required hardware and software to place the data on the downlink. Prior to the flight phase, a detailed set of flight test scenarios were developed to address the flight test objectives. Two cooperative collision avoidance sensors were utilized for detecting aircraft in the evaluation: Traffic Alert and Collision Avoidance System-II (TCAS-II) and Automatic Dependent Surveillance Broadcast (ADS-B). A single intruder aircraft was used during all the flight testing, a NASA Gulfstream III (G-III). During the course of the testing, six geometrically different near-collision scenarios were evaluated. These six scenarios were each tested using various combinations of sensors and collision avoidance software. Of the 54 planned test points 49 were accomplished successfully. Proteus flew a total of 21.5 hours during the testing and the G-III flew 19.8 hours. The testing fully achieved all flight test objectives. The Flight IPT performed an analysis to determine the accuracy of the simulation model used to predict the location of the host aircraft downstream during an avoidance maneuver. The data collected by this flight program was delivered to the Access 5 Cooperative Collision Avoidance (CCA) Work Package Team who was responsible for reporting on their analysis of this flight data.

An optimal control strategy for collision avoidance of mobile robots in non-stationary environments

NASA Technical Reports Server (NTRS)

Kyriakopoulos, K. J.; Saridis, G. N.

1991-01-01

An optimal control formulation of the problem of collision avoidance of mobile robots in environments containing moving obstacles is presented. Collision avoidance is guaranteed if the minimum distance between the robot and the objects is nonzero. A nominal trajectory is assumed to be known from off-line planning. The main idea is to change the velocity along the nominal trajectory so that collisions are avoided. Furthermore, time consistency with the nominal plan is desirable. A numerical solution of the optimization problem is obtained. Simulation results verify the value of the proposed strategy.

Collision avoidance in TV white spaces: a cross-layer design approach for cognitive radio networks

NASA Astrophysics Data System (ADS)

Foukalas, Fotis; Karetsos, George T.

2015-07-01

One of the most promising applications of cognitive radio networks (CRNs) is the efficient exploitation of TV white spaces (TVWSs) for enhancing the performance of wireless networks. In this paper, we propose a cross-layer design (CLD) of carrier sense multiple access with collision avoidance (CSMA/CA) mechanism at the medium access control (MAC) layer with spectrum sensing (SpSe) at the physical layer, for identifying the occupancy status of TV bands. The proposed CLD relies on a Markov chain model with a state pair containing both the SpSe and the CSMA/CA from which we derive the collision probability and the achievable throughput. Analytical and simulation results are obtained for different collision avoidance and SpSe implementation scenarios by varying the contention window, back off stage and probability of detection. The obtained results depict the achievable throughput under different collision avoidance and SpSe implementation scenarios indicating thereby the performance of collision avoidance in TVWSs-based CRNs.

UAS Collision Avoidance Algorithm that Minimizes the Impact on Route Surveillance

DTIC Science & Technology

2009-03-01

Appendix A: Collision Avoidance Algorithm/Virtual Cockpit Interface .......................124 Appendix B : Collision Cone Boundary Rates... b ) Split Cone (c) Multiple Intruders, Single and Split Cones [27] ........................................................ 27 3-3: Collision Cone...Approach in the Vertical Plane (a) Single Cone ( b ) Multiple Intruders, Single and Split Cone [27

Fighting Testing ACAT/FRRP: Automatic Collision Avoidance Technology/Fighter Risk Reduction Project

NASA Technical Reports Server (NTRS)

Skoog, Mark A.

2009-01-01

This slide presentation reviews the work of the Flight testing Automatic Collision Avoidance Technology/Fighter Risk Reduction Project (ACAT/FRRP). The goal of this project is to develop common modular architecture for all aircraft, and to enable the transition of technology from research to production as soon as possible to begin to reduce the rate of mishaps. The automated Ground Collision Avoidance System (GCAS) system is designed to prevent collision with the ground, by avionics that project the future trajectory over digital terrain, and request an evasion maneuver at the last instance. The flight controls are capable of automatically performing a recovery. The collision avoidance is described in the presentation. Also included in the presentation is a description of the flight test.

Integrated Collision Avoidance System for Air Vehicle

NASA Technical Reports Server (NTRS)

Lin, Ching-Fang (Inventor)

2013-01-01

Collision with ground/water/terrain and midair obstacles is one of the common causes of severe aircraft accidents. The various data from the coremicro AHRS/INS/GPS Integration Unit, terrain data base, and object detection sensors are processed to produce collision warning audio/visual messages and collision detection and avoidance of terrain and obstacles through generation of guidance commands in a closed-loop system. The vision sensors provide more information for the Integrated System, such as, terrain recognition and ranging of terrain and obstacles, which plays an important role to the improvement of the Integrated Collision Avoidance System.

Evaluation of an automotive rear-end collision avoidance system

DOT National Transportation Integrated Search

2006-04-01

This report presents the results of an independent evaluation of the Automotive Collision Avoidance System (ACAS). The ACAS integrates forward collision warning (FCW) and adaptive cruise control (ACC) functions for light-vehicle applications. The FCW...

Texture dependence of motion sensing and free flight behavior in blowflies

PubMed Central

Lindemann, Jens P.; Egelhaaf, Martin

2013-01-01

Many flying insects exhibit an active flight and gaze strategy: purely translational flight segments alternate with quick turns called saccades. To generate such a saccadic flight pattern, the animals decide the timing, direction, and amplitude of the next saccade during the previous translatory intersaccadic interval. The information underlying these decisions is assumed to be extracted from the retinal image displacements (optic flow), which scale with the distance to objects during the intersaccadic flight phases. In an earlier study we proposed a saccade-generation mechanism based on the responses of large-field motion-sensitive neurons. In closed-loop simulations we achieved collision avoidance behavior in a limited set of environments but observed collisions in others. Here we show by open-loop simulations that the cause of this observation is the known texture-dependence of elementary motion detection in flies, reflected also in the responses of large-field neurons as used in our model. We verified by electrophysiological experiments that this result is not an artifact of the sensory model. Already subtle changes in the texture may lead to qualitative differences in the responses of both our model cells and their biological counterparts in the fly's brain. Nonetheless, free flight behavior of blowflies is only moderately affected by such texture changes. This divergent texture dependence of motion-sensitive neurons and behavioral performance suggests either mechanisms that compensate for the texture dependence of the visual motion pathway at the level of the circuits generating the saccadic turn decisions or the involvement of a hypothetical parallel pathway in saccadic control that provides the information for collision avoidance independent of the textural properties of the environment. PMID:23335890

Investigation Of Alternative Displays For Side Collision Avoidance Systems, Final Report

DOT National Transportation Integrated Search

1996-12-01

DRIVER-VEHICLE INTERFACE OR DVI, HUMAN FACTORS, DRIVER PREFERENCES, INTELLIGENT VEHICLE INITIATIVE OR IVI : SIDE COLLISION AVOIDANCE SYSTEMS (SCAS) ARE DESIGNED TO WARN OF IMPENDING COLLISIONS AND CAN DETECT NOT ONLY ADJACENT VEHICLES BUT VEHICLES...

A neuro-collision avoidance strategy for robot manipulators

NASA Technical Reports Server (NTRS)

Onema, Joel P.; Maclaunchlan, Robert A.

1992-01-01

The area of collision avoidance and path planning in robotics has received much attention in the research community. Our study centers on a combination of an artificial neural network paradigm with a motion planning strategy that insures safe motion of the Articulated Two-Link Arm with Scissor Hand System relative to an object. Whenever an obstacle is encountered, the arm attempts to slide along the obstacle surface, thereby avoiding collision by means of the local tangent strategy and its artificial neural network implementation. This combination compensates the inverse kinematics of a robot manipulator. Simulation results indicate that a neuro-collision avoidance strategy can be achieved by means of a learning local tangent method.

Characterization Test Procedures for Intersection Collision Avoidance Systems Based on Vehicle-to-Vehicle Communications

DOT National Transportation Integrated Search

2015-12-01

Characterization test procedures have been developed to quantify the performance of intersection collision avoidance (ICA) systems based on vehicle-to-vehicle communications. These systems warn the driver of an imminent crossing-path collision at a r...

Power Mobility with Collision Avoidance for Older Adults: User, Caregiver and Prescriber Perspectives

PubMed Central

Wang, Rosalie H; Korotchenko, Alexandra; Clarke, Laura Hurd; Ben Mortenson, W; Mihailidis, Alex

2017-01-01

Collision avoidance technology has the capacity to facilitate safer mobility among older power mobility users with physical, sensory and cognitive impairments, thus enabling independence for more potential users. However, little is known about consumers’ perceptions of collision avoidance. This article draws on interviews with 29 users, five caregivers, and 10 prescribers to examine views on the design and utilization of this technology. Data analysis identified three themes: “useful situations or contexts”, “technology design issues and real life application”, and “appropriateness of collision avoidance technology for a variety of users”. Findings support the ongoing development of collision avoidance for older adult users. The majority of participants were supportive of the technology, and felt that it might benefit current power mobility users and users with visual impairments, but might be unsuitable for people with significant cognitive impairments. Some participants voiced concerns regarding the risk for injury with power mobility use and some identified situations where collision avoidance might be beneficial (driving backwards, avoiding dynamic obstacles, negotiating outdoor barriers, and learning power mobility use). Design issues include the need for context awareness, reliability, and user interface specifications. Furthermore, user desire to maintain driving autonomy indicates the need to develop collaboratively-controlled systems. This research lays the groundwork for future development by identifying and illustrating consumer needs for this technology. PMID:24458968

Towards Assessing the Human Trajectory Planning Horizon

PubMed Central

Nitsch, Verena; Meinzer, Dominik; Wollherr, Dirk

2016-01-01

Mobile robots are envisioned to cooperate closely with humans and to integrate seamlessly into a shared environment. For locomotion, these environments resemble traversable areas which are shared between multiple agents like humans and robots. The seamless integration of mobile robots into these environments requires accurate predictions of human locomotion. This work considers optimal control and model predictive control approaches for accurate trajectory prediction and proposes to integrate aspects of human behavior to improve their performance. Recently developed models are not able to reproduce accurately trajectories that result from sudden avoidance maneuvers. Particularly, the human locomotion behavior when handling disturbances from other agents poses a problem. The goal of this work is to investigate whether humans alter their trajectory planning horizon, in order to resolve abruptly emerging collision situations. By modeling humans as model predictive controllers, the influence of the planning horizon is investigated in simulations. Based on these results, an experiment is designed to identify, whether humans initiate a change in their locomotion planning behavior while moving in a complex environment. The results support the hypothesis, that humans employ a shorter planning horizon to avoid collisions that are triggered by unexpected disturbances. Observations presented in this work are expected to further improve the generalizability and accuracy of prediction methods based on dynamic models. PMID:27936015

Towards Assessing the Human Trajectory Planning Horizon.

PubMed

Carton, Daniel; Nitsch, Verena; Meinzer, Dominik; Wollherr, Dirk

2016-01-01

Mobile robots are envisioned to cooperate closely with humans and to integrate seamlessly into a shared environment. For locomotion, these environments resemble traversable areas which are shared between multiple agents like humans and robots. The seamless integration of mobile robots into these environments requires accurate predictions of human locomotion. This work considers optimal control and model predictive control approaches for accurate trajectory prediction and proposes to integrate aspects of human behavior to improve their performance. Recently developed models are not able to reproduce accurately trajectories that result from sudden avoidance maneuvers. Particularly, the human locomotion behavior when handling disturbances from other agents poses a problem. The goal of this work is to investigate whether humans alter their trajectory planning horizon, in order to resolve abruptly emerging collision situations. By modeling humans as model predictive controllers, the influence of the planning horizon is investigated in simulations. Based on these results, an experiment is designed to identify, whether humans initiate a change in their locomotion planning behavior while moving in a complex environment. The results support the hypothesis, that humans employ a shorter planning horizon to avoid collisions that are triggered by unexpected disturbances. Observations presented in this work are expected to further improve the generalizability and accuracy of prediction methods based on dynamic models.

Safety of High Speed and Ground Guided Transportation Systems: Collision Avoidance and Accident Survivability: Volume 1: Collision Threat

DOT National Transportation Integrated Search

1993-03-01

This report is the first of four volunes concerned with developing safety guidelines and specifications for high-speed : guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this : study i...

Safety of high-speed guided ground transportation : collision avoidance and accident survivability : volume 1 : collision threat

DOT National Transportation Integrated Search

1993-03-01

This report is the first of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is to...

75 FR 20671 - Seventieth Meeting: RTCA Special Committee 147: Minimum Operational Performance Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-20

... Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... RTCA Special Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision...

Experimental Studies Of Pilot Performance At Collision Avoidance During Closely Spaced Parallel Approaches

NASA Technical Reports Server (NTRS)

Pritchett, Amy R.; Hansman, R. John

1997-01-01

Efforts to increase airport capacity include studies of aircraft systems that would enable simultaneous approaches to closely spaced parallel runway in Instrument Meteorological Conditions (IMC). The time-critical nature of a parallel approach results in key design issues for current and future collision avoidance systems. Two part-task flight simulator studies have examined the procedural and display issues inherent in such a time-critical task, the interaction of the pilot with a collision avoidance system, and the alerting criteria and avoidance maneuvers preferred by subjects.

76 FR 11846 - Seventy-second Meeting: RTCA Special Committee 147: Minimum Operational Performance Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-03

... Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... Committee 147 meeting: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance... RTCA Special Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision...

75 FR 52590 - Seventy-First Meeting: RTCA Special Committee 147: Minimum Operational Performance Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-26

... Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... RTCA Special Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision...

76 FR 58077 - Seventy-Third Meeting: RTCA Special Committee 147: Minimum Operational Performance Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-19

... Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems... Committee 147 meeting: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance... RTCA Special Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision...

Collision Avoidance Functional Requirements for Step 1. Revision 6

NASA Technical Reports Server (NTRS)

2006-01-01

This Functional Requirements Document (FRD) describes the flow of requirements from the high level operational objectives down to the functional requirements specific to cooperative collision avoidance for high altitude, long endurance unmanned aircraft systems. These are further decomposed into performance and safety guidelines that are backed up by analysis or references to various documents or research findings. The FRD should be considered when establishing future policies, procedures, and standards pertaining to cooperative collision avoidance.

Optimal motion planning for collision avoidance of mobile robots in non-stationary environments

NASA Technical Reports Server (NTRS)

Kyriakopoulos, K. J.; Saridis, G. N.

1992-01-01

An optimal control formulation of the problem of collision avoidance of mobile robots moving in general terrains containing moving obstacles is presented. A dynamic model of the mobile robot and the dynamic constraints are derived. Collision avoidance is guaranteed if the minimum distance between the robot and the object is nonzero. A nominal trajectory is assumed to be known from off-line planning. The main idea is to change the velocity along the nominal trajectory so that collisions are avoided. Time consistency with the nominal plan is desirable. A numerical solution of the optimization problem is obtained. A perturbation control type of approach is used to update the optimal plan. Simulation results verify the value of the proposed strategy.

Modeling perspectives on echolocation strategies inspired by bats flying in groups.

PubMed

Lin, Yuan; Abaid, Nicole

2015-12-21

Bats navigating with echolocation - which is a type of active sensing achieved by interpreting echoes resulting from self-generated ultrasonic pulses - exhibit unique behaviors during group flight. While bats may benefit from eavesdropping on their peers׳ echolocation, they also potentially suffer from confusion between their own and peers׳ pulses, caused by an effect called frequency jamming. This hardship of group flight is supported by experimental observations of bats simplifying their sound-scape by shifting their pulse frequencies or suppressing echolocation altogether. Here, we investigate eavesdropping and varying pulse emission rate from a modeling perspective to understand these behaviors׳ potential benefits and detriments. We define an agent-based model of echolocating bats avoiding collisions in a three-dimensional tunnel. Through simulation, we show that bats with reasonably accurate eavesdropping can reduce collisions compared to those neglecting information from peers. In large populations, bats minimize frequency jamming by decreasing pulse emission rate, while collision risk increases; conversely, increasing pulse emission rate minimizes collisions by allowing more sensing information generated per bat. These strategies offer benefits for both biological and engineered systems, since frequency jamming is a concern in systems using active sensing. Copyright © 2015 Elsevier Ltd. All rights reserved.

LightForce: An Update on Orbital Collision Avoidance Using Photon Pressure

NASA Technical Reports Server (NTRS)

Stupl, Jan; Mason, James; De Vries, Willem; Smith, Craig; Levit, Creon; Marshall, William; Salas, Alberto Guillen; Pertica, Alexander; Olivier, Scot; Ting, Wang

2012-01-01

We present an update on our research on collision avoidance using photon-pressure induced by ground-based lasers. In the past, we have shown the general feasibility of employing small orbit perturbations, induced by photon pressure from ground-based laser illumination, for collision avoidance in space. Possible applications would be protecting space assets from impacts with debris and stabilizing the orbital debris environment. Focusing on collision avoidance rather than de-orbit, the scheme avoids some of the security and liability implications of active debris removal, and requires less sophisticated hardware than laser ablation. In earlier research we concluded that one ground based system consisting of a 10 kW class laser, directed by a 1.5 m telescope with adaptive optics, could avoid a significant fraction of debris-debris collisions in low Earth orbit. This paper describes our recent efforts, which include refining our original analysis, employing higher fidelity simulations and performing experimental tracking tests. We investigate the efficacy of one or more laser ground stations for debris-debris collision avoidance and satellite protection using simulations to investigate multiple case studies. The approach includes modeling of laser beam propagation through the atmosphere, the debris environment (including actual trajectories and physical parameters), laser facility operations, and simulations of the resulting photon pressure. We also present the results of experimental laser debris tracking tests. These tests track potential targets of a first technical demonstration and quantify the achievable tracking performance.

Radar-based collision avoidance for unmanned surface vehicles

NASA Astrophysics Data System (ADS)

Zhuang, Jia-yuan; Zhang, Lei; Zhao, Shi-qi; Cao, Jian; Wang, Bo; Sun, Han-bing

2016-12-01

Unmanned surface vehicles (USVs) have become a focus of research because of their extensive applications. To ensure safety and reliability and to perform complex tasks autonomously, USVs are required to possess accurate perception of the environment and effective collision avoidance capabilities. To achieve these, investigation into realtime marine radar target detection and autonomous collision avoidance technologies is required, aiming at solving the problems of noise jamming, uneven brightness, target loss, and blind areas in marine radar images. These technologies should also satisfy the requirements of real-time and reliability related to high navigation speeds of USVs. Therefore, this study developed an embedded collision avoidance system based on the marine radar, investigated a highly real-time target detection method which contains adaptive smoothing algorithm and robust segmentation algorithm, developed a stable and reliable dynamic local environment model to ensure the safety of USV navigation, and constructed a collision avoidance algorithm based on velocity obstacle (V-obstacle) which adjusts the USV's heading and speed in real-time. Sea trials results in multi-obstacle avoidance firstly demonstrate the effectiveness and efficiency of the proposed avoidance system, and then verify its great adaptability and relative stability when a USV sailing in a real and complex marine environment. The obtained results will improve the intelligent level of USV and guarantee the safety of USV independent sailing.

A method of inferring collision ratio based on maneuverability of own ship under critical collision conditions

NASA Astrophysics Data System (ADS)

You, Youngjun; Rhee, Key-Pyo; Ahn, Kyoungsoo

2013-06-01

In constructing a collision avoidance system, it is important to determine the time for starting collision avoidance maneuver. Many researchers have attempted to formulate various indices by applying a range of techniques. Among these indices, collision risk obtained by combining Distance to the Closest Point of Approach (DCPA) and Time to the Closest Point of Approach (TCPA) information with fuzzy theory is mostly used. However, the collision risk has a limit, in that membership functions of DCPA and TCPA are empirically determined. In addition, the collision risk is not able to consider several critical collision conditions where the target ship fails to take appropriate actions. It is therefore necessary to design a new concept based on logical approaches. In this paper, a collision ratio is proposed, which is the expected ratio of unavoidable paths to total paths under suitably characterized operation conditions. Total paths are determined by considering categories such as action space and methodology of avoidance. The International Regulations for Preventing Collisions at Sea (1972) and collision avoidance rules (2001) are considered to solve the slower ship's dilemma. Different methods which are based on a constant speed model and simulated speed model are used to calculate the relative positions between own ship and target ship. In the simulated speed model, fuzzy control is applied to determination of command rudder angle. At various encounter situations, the time histories of the collision ratio based on the simulated speed model are compared with those based on the constant speed model.

Active Collision Avoidance for Planetary Landers

NASA Technical Reports Server (NTRS)

Rickman, Doug; Hannan, Mike; Srinivasan, Karthik

2014-01-01

Present day robotic missions to other planets require precise, a priori knowledge of the terrain to pre-determine a landing spot that is safe. Landing sites can be miles from the mission objective, or, mission objectives may be tailored to suit landing sites. Future robotic exploration missions should be capable of autonomously identifying a safe landing target within a specified target area selected by mission requirements. Such autonomous landing sites must (1) 'see' the surface, (2) identify a target, and (3) land the vehicle. Recent advances in radar technology have resulted in small, lightweight, low power radars that are used for collision avoidance and cruise control systems in automobiles. Such radar systems can be adapted for use as active hazard avoidance systems for planetary landers. The focus of this CIF proposal is to leverage earlier work on collision avoidance systems for MSFC's Mighty Eagle lander and evaluate the use of automotive radar systems for collision avoidance in planetary landers.

Modeling and Simulation of an UAS Collision Avoidance Systems

NASA Technical Reports Server (NTRS)

Oliveros, Edgardo V.; Murray, A. Jennifer

2010-01-01

This paper describes a Modeling and Simulation of an Unmanned Aircraft Systems (UAS) Collision Avoidance System, capable of representing different types of scenarios for UAS collision avoidance. Commercial and military piloted aircraft currently utilize various systems for collision avoidance such as Traffic Alert and Collision A voidance System (TCAS), Automatic Dependent Surveillance-Broadcast (ADS-B), Radar and ElectroOptical and Infrared Sensors (EO-IR). The integration of information from these systems is done by the pilot in the aircraft to determine the best course of action. In order to operate optimally in the National Airspace System (NAS) UAS have to work in a similar or equivalent manner to a piloted aircraft by applying the principle of "detect-see and avoid" (DSA) to other air traffic. Hence, we have taken these existing sensor technologies into consideration in order to meet the challenge of researching the modeling and simulation of an approximated DSA system. A Schematic Model for a UAS Collision Avoidance System (CAS) has been developed ina closed loop block diagram for that purpose. We have found that the most suitable software to carry out this task is the Satellite Tool Kit (STK) from Analytical Graphics Inc. (AGI). We have used the Aircraft Mission Modeler (AMM) for modeling and simulation of a scenario where a UAS is placed on a possible collision path with an initial intruder and then with a second intruder, but is able to avoid them by executing a right tum maneuver and then climbing. Radars have also been modeled with specific characteristics for the UAS and both intruders. The software provides analytical, graphical user interfaces and data controlling tools which allow the operator to simulate different conditions. Extensive simulations have been carried out which returned excellent results.

SU-F-BRB-05: Collision Avoidance Mapping Using Consumer 3D Camera

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cardan, R; Popple, R

2015-06-15

Purpose: To develop a fast and economical method of scanning a patient’s full body contour for use in collision avoidance mapping without the use of ionizing radiation. Methods: Two consumer level 3D cameras used in electronic gaming were placed in a CT simulator room to scan a phantom patient set up in a high collision probability position. A registration pattern and computer vision algorithms were used to transform the scan into the appropriate coordinate systems. The cameras were then used to scan the surface of a gantry in the treatment vault. Each scan was converted into a polygon mesh formore » collision testing in a general purpose polygon interference algorithm. All clinically relevant transforms were applied to the gantry and patient support to create a map of all possible collisions. The map was then tested for accuracy by physically testing the collisions with the phantom in the vault. Results: The scanning fidelity of both the gantry and patient was sufficient to produce a collision prediction accuracy of 97.1% with 64620 geometry states tested in 11.5 s. The total scanning time including computation, transformation, and generation was 22.3 seconds. Conclusion: Our results demonstrate an economical system to generate collision avoidance maps. Future work includes testing the speed of the framework in real-time collision avoidance scenarios. Research partially supported by a grant from Varian Medical Systems.« less

Defining the Collision Avoidance Region for DAA Systems

NASA Technical Reports Server (NTRS)

Thipphavong, David; Cone, Andrew; Park, Chunki; Lee, Seung Man; Santiago, Confesor

2016-01-01

Unmanned aircraft systems (UAS) will be required to equip with a detect-­-and-­-avoid (DAA) system in order to satisfy the federal aviation regulations to maintain well clear of other aircraft, some of which may be equipped with a Traffic Collision Avoidance System (TCAS) to mitigate the possibility of mid-­-air collisions. As such, the minimum operational performance standards (MOPS) for UAS DAA systems are being designed with TCAS interoperability in mind by a group of industry, government, and academic institutions named RTCA Special Committee-228 (SC-228). This document will discuss the development of the spatial-­-temporal volume known as the collision avoidance region in which the DAA system is not allowed to provide vertical guidance to maintain or regain DAA well clear that could conflict with resolution advisories (RAs) issued by the intruder aircraft's TCAS system. Three collision avoidance region definition candidates were developed based on the existing TCAS RA and DAA alerting definitions. They were evaluated against each other in terms of their interoperability with TCAS RAs and DAA alerts in an unmitigated factorial encounter analysis of 1.3 million simulated pairs.

The computer coordination method and research of inland river traffic based on ship database

NASA Astrophysics Data System (ADS)

Liu, Shanshan; Li, Gen

2018-04-01

A computer coordinated management method for inland river ship traffic is proposed in this paper, Get the inland ship's position, speed and other navigation information by VTS, building ship's statics and dynamic data bases, writing a program of computer coordinated management of inland river traffic by VB software, Automatic simulation and calculation of the meeting states of ships, Providing ship's long-distance collision avoidance information. The long-distance collision avoidance of ships will be realized. The results show that, Ships avoid or reduce meetings, this method can effectively control the macro collision avoidance of ships.

ED09-0290-32

NASA Image and Video Library

2009-10-01

The F-16D Automatic Collision Avoidance Technology aircraft tests of the Automatic Ground Collision Avoidance System, or Auto-GCAS, included flights in areas of potentially hazardous terrain, including canyons and mountains.

Collision warning and avoidance considerations for the Space Shuttle and Space Station Freedom

NASA Technical Reports Server (NTRS)

Vilas, Faith; Collins, Michael F.; Kramer, Paul C.; Arndt, G. Dickey; Suddath, Jerry H.

1990-01-01

The increasing hazard of manmade debris in low earth orbit (LEO) has focused attention on the requirement for collision detection, warning and avoidance systems to be developed in order to protect manned (and unmanned) spacecraft. With the number of debris objects expected to be increasing with time, the impact hazard will also be increasing. The safety of the Space Shuttle and the Space Station Freedom from destructive or catastrophic collision resulting from the hypervelocity impact of a LEO object is of increasing concern to NASA. A number of approaches to this problem are in effect or under development. The collision avoidance procedures now in effect for the Shuttle are described, and detection and avoidance procedures presently being developed at the Johnson Space Center for the Space Station Freedom are discussed.

An integrated collision prediction and avoidance scheme for mobile robots in non-stationary environments

NASA Technical Reports Server (NTRS)

Kyriakopoulos, K. J.; Saridis, G. N.

1993-01-01

A formulation that makes possible the integration of collision prediction and avoidance stages for mobile robots moving in general terrains containing moving obstacles is presented. A dynamic model of the mobile robot and the dynamic constraints are derived. Collision avoidance is guaranteed if the distance between the robot and a moving obstacle is nonzero. A nominal trajectory is assumed to be known from off-line planning. The main idea is to change the velocity along the nominal trajectory so that collisions are avoided. A feedback control is developed and local asymptotic stability is proved if the velocity of the moving obstacle is bounded. Furthermore, a solution to the problem of inverse dynamics for the mobile robot is given. Simulation results verify the value of the proposed strategy.

NHTSA light vehicle antilock brake systems research program task 5, part 1 : examination of drivers' collision avoidance behavior using conventional and antilock brake systems on the Iowa driving simulator

DOT National Transportation Integrated Search

2000-08-01

The National Highway Traffic Safety Administration (NHTSA) has developed its Light Vehicle Antilock Brake Systems (ABS) Research Program in an effort to determine the cause(s) of the apparent increase in single-vehicle run-off-road crashes and decrea...

Earth Observing System (EOS) Aqua and Aura Space Weather Effects on Operational Collision Avoidance

NASA Technical Reports Server (NTRS)

Guit, Bill

2017-01-01

This presentation will describe recent EOS Aqua and Aura operational collision avoidance experience during periods of solar and geomagnetic storm activity. It will highlight challenges faced by the operations team during short-notice, high-risk predicted close approaches. The presentation will highlight the evolution of the operational collision avoidance process for the EOS Aqua and Aura missions. The presentation will highlight operational challenges that have occurred, process improvements that have been implemented and identify potential future challenges.

Horizontal Collision Avoidance Systems Study

DOT National Transportation Integrated Search

1973-12-01

This report presents the results of an analytical study of the merits and mechanization requirements of horizontal collision avoidance systems (CAS). The horizontal and combined horizontal/vertical maneuvers which provide adequate miss distance with ...

Exposure safety standards for nonionizing radiation (NIR) from collision-avoidance radar

NASA Astrophysics Data System (ADS)

Palmer-Fortune, Joyce; Brecher, Aviva; Spencer, Paul; Huguenin, Richard; Woods, Ken

1997-02-01

On-vehicle technology for collision avoidance using millimeter wave radar is currently under development and is expected to be in vehicles in coming years. Recently approved radar bands for collision avoidance applications include 47.5 - 47.8 GHz and 76 - 77 GHz. Widespread use of active radiation sources in the public domain would contribute to raised levels of human exposure to high frequency electromagnetic radiation, with potential for adverse health effects. In order to design collision avoidance systems that will pose an acceptably low radiation hazard, it is necessary to determine what levels of electromagnetic radiation at millimeter wave frequencies will be acceptable in the environment. This paper will summarize recent research on NIR (non-ionizing radiation) exposure safety standards for high frequency electromagnetic radiation. We have investigated both governmental and non- governmental professional organizations worldwide.

A problem of collision avoidance

NASA Technical Reports Server (NTRS)

Vincent, T. L.; Cliff, E. M.; Grantham, W. J.; Peng, W. Y.

1972-01-01

Collision avoidance between two vehicles of constant speed with limited turning radii, moving in a horizontal plane is investigated. Collision avoidance is viewed as a game by assuming that the operator of one vehicle has perfect knowledge of the state of the other, whereas the operator of the second vehicle is unaware of any impending danger. The situation envisioned is that of an encounter between a commercial aircraft and a small light aircraft. This worse case situation is examined to determine the conditions under which the commercial aircraft should execute a collision avoidance maneuver. Three different zones of vulnerability are defined and the boundaries, or barriers, between these zones are determined for a typical aircraft encounter. A discussion of the methods used to obtain the results as well as some of the salient features associated with the resultant barriers is included.

SU-F-T-235: Optical Scan Based Collision Avoidance Using Multiple Stereotactic Cameras During Simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cardan, R; Popple, R; Dobelbower, M

Purpose: To demonstrate the ability to quickly generate an accurate collision avoidance map using multiple stereotactic cameras during simulation. Methods: Three Kinect stereotactic cameras were placed in the CT simulation room and optically calibrated to the DICOM isocenter. Immediately before scanning, the patient was optically imaged to generate a 3D polygon mesh, which was used to calculate the collision avoidance area using our previously developed framework. The mesh was visually compared to the CT scan body contour to ensure accurate coordinate alignment. To test the accuracy of the collision calculation, the patient and machine were physically maneuvered in the treatmentmore » room to calculated collision boundaries. Results: The optical scan and collision calculation took 38.0 seconds and 2.5 seconds to complete respectively. The collision prediction accuracy was determined using a receiver operating curve (ROC) analysis, where the true positive, true negative, false positive and false negative values were 837, 821, 43, and 79 points respectively. The ROC accuracy was 93.1% over the sampled collision space. Conclusion: We have demonstrated a framework which is fast and accurate for predicting collision avoidance for treatment which can be determined during the normal simulation process. Because of the speed, the system could be used to add a layer of safety with a negligible impact on the normal patient simulation experience. This information could be used during treatment planning to explore the feasible geometries when optimizing plans. Research supported by Varian Medical Systems.« less

Formation control of robotic swarm using bounded artificial forces.

PubMed

Qin, Long; Zha, Yabing; Yin, Quanjun; Peng, Yong

2013-01-01

Formation control of multirobot systems has drawn significant attention in the recent years. This paper presents a potential field control algorithm, navigating a swarm of robots into a predefined 2D shape while avoiding intermember collisions. The algorithm applies in both stationary and moving targets formation. We define the bounded artificial forces in the form of exponential functions, so that the behavior of the swarm drove by the forces can be adjusted via selecting proper control parameters. The theoretical analysis of the swarm behavior proves the stability and convergence properties of the algorithm. We further make certain modifications upon the forces to improve the robustness of the swarm behavior in the presence of realistic implementation considerations. The considerations include obstacle avoidance, local minima, and deformation of the shape. Finally, detailed simulation results validate the efficiency of the proposed algorithm, and the direction of possible futrue work is discussed in the conclusions.

Formation Control of Robotic Swarm Using Bounded Artificial Forces

PubMed Central

Zha, Yabing; Peng, Yong

2013-01-01

Formation control of multirobot systems has drawn significant attention in the recent years. This paper presents a potential field control algorithm, navigating a swarm of robots into a predefined 2D shape while avoiding intermember collisions. The algorithm applies in both stationary and moving targets formation. We define the bounded artificial forces in the form of exponential functions, so that the behavior of the swarm drove by the forces can be adjusted via selecting proper control parameters. The theoretical analysis of the swarm behavior proves the stability and convergence properties of the algorithm. We further make certain modifications upon the forces to improve the robustness of the swarm behavior in the presence of realistic implementation considerations. The considerations include obstacle avoidance, local minima, and deformation of the shape. Finally, detailed simulation results validate the efficiency of the proposed algorithm, and the direction of possible futrue work is discussed in the conclusions. PMID:24453809

Study on the Correlation Between Dynamical Behavior and Friction/Wear Mechanism Under the Effect of Grooves

NASA Astrophysics Data System (ADS)

Zhu, Z. Y.; Mo, J. L.; Wang, D. W.; Zhao, J.; Zhu, M. H.; Zhou, Z. R.

2018-04-01

In this work, the interfacial friction and wear and vibration characteristics are studied by sliding a chromium bearing steel ball (AISI 52100) over both multi-grooved and single-grooved forged steel disks (20CrMnMo) at low and high rotating speeds in order to reveal the effect mechanism of groove-textured surface on tribological behaviors. The results show that the grooves modify the contact state of the ball and the disk at the contact interface. This consequently causes variations in the normal displacement, normal force, and friction force signals. The changes in these three signals become more pronounced with increasing groove width at a low speed. The collision behavior between the ball and the groove increase the amplitude of vibration acceleration at a high speed. The test results suggest that grooves with appropriate widths could trap wear debris on the ball surface while avoiding a strong collision between the disk and the ball, resulting in an improvement in the wear states.

The COLA Collision Avoidance Method

NASA Astrophysics Data System (ADS)

Assmann, K.; Berger, J.; Grothkopp, S.

2009-03-01

In the following we present a collision avoidance method named COLA. The method has been designed to predict collisions for Earth orbiting spacecraft on any orbits, including orbit changes, with other space-born objects. The point in time of a collision and the collision probability are determined. To guarantee effective processing the COLA method uses a modular design and is composed of several components which are either developed within this work or deduced from existing algorithms: A filtering module, the close approach determination, the collision detection and the collision probability calculation. A software tool which implements the COLA method has been verified using various test cases built from sample missions. This software has been implemented in the C++ programming language and serves as a universal collision detection tool at LSE Space Engineering & Operations AG.

Sense and Avoid Safety Analysis for Remotely Operated Unmanned Aircraft in the National Airspace System. Version 5

NASA Technical Reports Server (NTRS)

Carreno, Victor

2006-01-01

This document describes a method to demonstrate that a UAS, operating in the NAS, can avoid collisions with an equivalent level of safety compared to a manned aircraft. The method is based on the calculation of a collision probability for a UAS , the calculation of a collision probability for a base line manned aircraft, and the calculation of a risk ratio given by: Risk Ratio = P(collision_UAS)/P(collision_manned). A UAS will achieve an equivalent level of safety for collision risk if the Risk Ratio is less than or equal to one. Calculation of the probability of collision for UAS and manned aircraft is accomplished through event/fault trees.

Ground Collision Avoidance System (Igcas)

NASA Technical Reports Server (NTRS)

Prosser, Kevin (Inventor); Hook, Loyd (Inventor); Skoog, Mark A (Inventor)

2017-01-01

The present invention is a system and method for aircraft ground collision avoidance (iGCAS) comprising a modular array of software, including a sense own state module configured to gather data to compute trajectory, a sense terrain module including a digital terrain map (DTM) and map manger routine to store and retrieve terrain elevations, a predict collision threat module configured to generate an elevation profile corresponding to the terrain under the trajectory computed by said sense own state module, a predict avoidance trajectory module configured to simulate avoidance maneuvers ahead of the aircraft, a determine need to avoid module configured to determine which avoidance maneuver should be used, when it should be initiated, and when it should be terminated, a notify Module configured to display each maneuver's viability to the pilot by a colored GUI, a pilot controls module configured to turn the system on and off, and an avoid module configured to define how an aircraft will perform avoidance maneuvers through 3-dimensional space.

Automotive collision avoidance system field operational test

DOT National Transportation Integrated Search

2005-03-01

The Automotive Collision Avoidance System field operational test (or ACAS FOT) program was led by General Motors (GM) under a cooperative agreement with the U.S. Department of Transportation. This report summarizes the activities of the entire progra...

Design and evaluation of steering protection for avoiding collisions during a lane change.

PubMed

Itoh, Makoto; Inagaki, Toshiyuki

2014-01-01

This paper discusses the design of a driver assistance system for avoiding collisions with vehicles in blind spots. The following three types of support systems are compared: (1) a warning system that provides the driver with an auditory alert, (2) a 'soft' protection system that makes the steering wheel stiffer to tell the driver that a lane-change manoeuvre is not recommended and (3) a 'hard' protection system that cancels the driver's input and controls the tyre angle autonomously to prevent lane departure. The results of an experiment showed that the hard protection system was more effective for collision avoidance than either the warning or the soft protection system. The warning and soft protection systems were almost the same in terms of collision avoidance. The results suggest that the human-centred automation principle, which requires the human to have the final authority over the automation, can be violated depending on the context.

Effectiveness and driver acceptance of a semi-autonomous forward obstacle collision avoidance system.

PubMed

Itoh, Makoto; Horikome, Tatsuya; Inagaki, Toshiyuki

2013-09-01

This paper proposes a semi-autonomous collision avoidance system for the prevention of collisions between vehicles and pedestrians and objects on a road. The system is designed to be compatible with the human-centered automation principle, i.e., the decision to perform a maneuver to avoid a collision is made by the driver. However, the system is partly autonomous in that it turns the steering wheel independently when the driver only applies the brake, indicating his or her intent to avoid the obstacle. With a medium-fidelity driving simulator, we conducted an experiment to investigate the effectiveness of this system for improving safety in emergency situations, as well as its acceptance by drivers. The results indicate that the system effectively improves safety in emergency situations, and the semi-autonomous characteristic of the system was found to be acceptable to drivers. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Millimeter wave backscatter measurements in support of collision avoidance applications

NASA Astrophysics Data System (ADS)

Narayanan, Ram M.; Snuttjer, Brett R. J.

1997-11-01

Millimeter-wave short range radar systems have unique advantages in surface navigation applications, such as military vehicle mobility, aircraft landing assistance, and automotive collision avoidance. In collision avoidance applications, characterization of clutter due to terrain and roadside objects is necessary in order to maximize the signal-to-clutter ratio (SCR) and to minimize false alarms. The results of two types of radar cross section (RCS) measurements at 95 GHz are reported in this paper. The first set of measurements presents data on the normalized RCS (NRCS) as well as clutter distributions of various terrain types at low grazing angles of 5° and 7.5°. The second set of measurements presents RCS data and statistics on various types of roadside objects, such as metallic and wooden sign posts. These results are expected to be useful for designers of short-range millimeter-wave collision avoidance radar systems.

How do walkers behave when crossing the way of a mobile robot that replicates human interaction rules?

PubMed

Vassallo, Christian; Olivier, Anne-Hélène; Souères, Philippe; Crétual, Armel; Stasse, Olivier; Pettré, Julien

2018-02-01

Previous studies showed the existence of implicit interaction rules shared by human walkers when crossing each other. Especially, each walker contributes to the collision avoidance task and the crossing order, as set at the beginning, is preserved along the interaction. This order determines the adaptation strategy: the first arrived increases his/her advance by slightly accelerating and changing his/her heading, whereas the second one slows down and moves in the opposite direction. In this study, we analyzed the behavior of human walkers crossing the trajectory of a mobile robot that was programmed to reproduce this human avoidance strategy. In contrast with a previous study, which showed that humans mostly prefer to give the way to a non-reactive robot, we observed similar behaviors between human-human avoidance and human-robot avoidance when the robot replicates the human interaction rules. We discuss this result in relation with the importance of controlling robots in a human-like way in order to ease their cohabitation with humans. Copyright © 2017 Elsevier B.V. All rights reserved.

Avoidance maneuevers selected while viewing cockpit traffic displays

NASA Technical Reports Server (NTRS)

Smith, J. D.; Ellis, S. R.; Lee, E.

1982-01-01

Ten airline pilots rates the collision danger of air traffic presented on cockpit displays of traffic information while they monitored simulated departures from Denver. They selected avoidance maneuvers when necessary for separation. Most evasive maneuvers were turns rather than vertical maneuvers. Evasive maneuvers chosen for encounters with low or moderate collision danger were generally toward the intruding aircraft. This tendency lessened as the perceived threat level increased. In the highest threst situations pilots turned toward the intruder only at chance levels. Intruders coming from positions in front of the pilot's own ship were more frequently avoided by turns toward than when intruders approached laterally or from behind. Some of the implications of the pilots' turning-toward tendencies are discussed with respect to automatic collision avoidance systems and coordination of avoidance maneuvers of conflicting aircraft.

Reactive Collision Avoidance Algorithm

NASA Technical Reports Server (NTRS)

Scharf, Daniel; Acikmese, Behcet; Ploen, Scott; Hadaegh, Fred

2010-01-01

The reactive collision avoidance (RCA) algorithm allows a spacecraft to find a fuel-optimal trajectory for avoiding an arbitrary number of colliding spacecraft in real time while accounting for acceleration limits. In addition to spacecraft, the technology can be used for vehicles that can accelerate in any direction, such as helicopters and submersibles. In contrast to existing, passive algorithms that simultaneously design trajectories for a cluster of vehicles working to achieve a common goal, RCA is implemented onboard spacecraft only when an imminent collision is detected, and then plans a collision avoidance maneuver for only that host vehicle, thus preventing a collision in an off-nominal situation for which passive algorithms cannot. An example scenario for such a situation might be when a spacecraft in the cluster is approaching another one, but enters safe mode and begins to drift. Functionally, the RCA detects colliding spacecraft, plans an evasion trajectory by solving the Evasion Trajectory Problem (ETP), and then recovers after the collision is avoided. A direct optimization approach was used to develop the algorithm so it can run in real time. In this innovation, a parameterized class of avoidance trajectories is specified, and then the optimal trajectory is found by searching over the parameters. The class of trajectories is selected as bang-off-bang as motivated by optimal control theory. That is, an avoiding spacecraft first applies full acceleration in a constant direction, then coasts, and finally applies full acceleration to stop. The parameter optimization problem can be solved offline and stored as a look-up table of values. Using a look-up table allows the algorithm to run in real time. Given a colliding spacecraft, the properties of the collision geometry serve as indices of the look-up table that gives the optimal trajectory. For multiple colliding spacecraft, the set of trajectories that avoid all spacecraft is rapidly searched on-line. The optimal avoidance trajectory is implemented as a receding-horizon model predictive control law. Therefore, at each time step, the optimal avoidance trajectory is found and the first time step of its acceleration is applied. At the next time step of the control computer, the problem is re-solved and the new first time step is again applied. This continual updating allows the RCA algorithm to adapt to a colliding spacecraft that is making erratic course changes.

Active Collision Avoidance for Planetary Landers

NASA Technical Reports Server (NTRS)

Rickman, Doug; Hannan, Mike; Srinivasan, Karthik

2015-01-01

The use of automotive radar systems are being evaluated for collision avoidance in planetary landers. Our focus is to develop a low-cost, light-weight collision avoidance system that overcomes the drawbacks identified with optical-based systems. We also seek to complement the Autonomous Landing and Hazard Avoidance Technology system by providing mission planners an alternative system that can be used on low-cost, small robotic missions and in close approach. Our approach takes advantage of how electromagnetic radiation interacts with solids. As the wavelength increases, the sensitivity of the radiation to isolated solids of a specific particle size decreases. Thus, rocket exhaust-blown dust particles, which have major significance in visible wavelengths, have much less significance at radar wavelengths.

How Usability Testing Resulted in Improvements to Ground Collision Software for General Aviation: Improved Ground Collision Avoidance System (IGCAS)

NASA Technical Reports Server (NTRS)

Lamarr, Michael; Chinske, Chris; Williams, Ethan; Law, Cameron; Skoog, Mark; Sorokowski, Paul

2016-01-01

The NASA improved Ground Collision Avoidance System (iGCAS) team conducted an onsite usability study at Experimental Aircraft Association (EAA) Air Venture in Oshkosh, Wisconsin from July 19 through July 26, 2015. EAA Air Venture had approximately 550,000 attendees from which the sample pool of pilots were selected. The objectives of this study were to assess the overall appropriateness and acceptability of iGCAS as a warning system for General Aviation aircraft, usability of the iGCAS displays and audio cues, test terrain avoidance characteristics, performance, functionality, pilot response time, and correlate terrain avoidance performance and pilot response time data.

Effect of perceived threat on avoidance maneuvers selected while viewing cockpit traffic displays

NASA Technical Reports Server (NTRS)

Smith, J. D.; Ellis, S. R.

1982-01-01

Ten airline pilots rated the collision danger of air traffic presented on cockpit displays of traffic information (CDTI) while they monitored simulated departures from Denver. They selected avoidance maneuvers when necessary for separation. Most evasive maneuvers were turns rather than vertical maneuvers. Evasive maneuvers chosen for encounters with low or moderate perceived collision danger were generally toward the intruding aircraft. This tendency lessened as the perceived threat level increased. In the highest threat situations pilots turned toward the intruder only at chance levels. Some of the implications of the pilots' turning-towards tendencies are discussed with respect to automatic collision avoidance systems and coordination of avoidance maneuvers of conflicting aircraft.

All weather collision avoidance for unmanned aircraft systems

NASA Astrophysics Data System (ADS)

Contarino, Mark

2010-04-01

For decades, military and other national security agencies have been denied unfettered access to the National Air Space (NAS) because their unmanned aircraft lack a highly reliable and effective collision avoidance capability. The controlling agency, the Federal Aviation Administration, justifiably demands "no harm" to the safety of the NAS. To overcome the constraints imposed on Unmanned Aircraft Systems (UAS) use of the NAS, a new, complex, conformable collision avoidance system has been developed - one that will be effective in all flyable weather conditions, overcoming the shortfalls of other sensing systems, including radar, lidar, acoustic, EO/IR, etc., while meeting form factor and cost criteria suitable for Tier II UAS operations. The system also targets Tier I as an ultimate goal, understanding the operational limitations of the smallest UASs may require modification of the design that is suitable for Tier II and higher. The All Weather Sense and Avoid System (AWSAS) takes into account the FAA's plan to incorporate ADS-B (out) for all aircraft by 2020, and it is intended to make collision avoidance capability available for UAS entry into the NAS as early as 2013. When approved, UASs can fly mission or training flights in the NAS free of the constraints presently in place. Upon implementation this system will achieve collision avoidance capability for UASs deployed for national security purposes and will allow expansion of UAS usage for commercial or other civil purposes.

Robot body self-modeling algorithm: a collision-free motion planning approach for humanoids.

PubMed

Leylavi Shoushtari, Ali

2016-01-01

Motion planning for humanoid robots is one of the critical issues due to the high redundancy and theoretical and technical considerations e.g. stability, motion feasibility and collision avoidance. The strategies which central nervous system employs to plan, signal and control the human movements are a source of inspiration to deal with the mentioned problems. Self-modeling is a concept inspired by body self-awareness in human. In this research it is integrated in an optimal motion planning framework in order to detect and avoid collision of the manipulated object with the humanoid body during performing a dynamic task. Twelve parametric functions are designed as self-models to determine the boundary of humanoid's body. Later, the boundaries which mathematically defined by the self-models are employed to calculate the safe region for box to avoid the collision with the robot. Four different objective functions are employed in motion simulation to validate the robustness of algorithm under different dynamics. The results also confirm the collision avoidance, reality and stability of the predicted motion.

Beacon Collision Avoidance System (BCAS) Alternative Concepts for Determining Target Positions

DOT National Transportation Integrated Search

1978-09-01

The (Litchford) Beacon-based Collision Avoidance System concept requires the computation of target range and bearing relative to the BCAS aircraft. Techniques for determining target range and bearing under four different assumptions about the ground ...

Collision avoidance system cost-benefit analysis : volume I - technical manual

DOT National Transportation Integrated Search

1981-09-01

Collision-avoidance systems under development in the U.S.A., Japan and Germany were evaluated. The performance evaluation showed that the signal processing and the control law of a system were the key parameters that decided the system's capability, ...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures, Task 1, Volume 2: Support Volume, Final Report

DOT National Transportation Integrated Search

1994-10-01

THE RUN-OFF-ROAD COLLISION AVOIDANCE USING LVHS COUNTERMEASURES PROGRAM IS TO ADDRESS THE SINGLE VEHICLE CRASH PROBLEM THROUGH APPLICATION OF TECHNOLOGY TO PREVENT AND/OR REDUCE THE SEVERITY OF THESE CRASHES.

Cooperative Intersection Collision Avoidance System for Violations (CICAS-V) : Database Structure

DOT National Transportation Integrated Search

2011-07-01

This report documents the process required for data exchange between a conductor of a field operational test (FOT) and an independent evaluator based on the experience of the Cooperative Intersection Collision Avoidance System for Violations (CICAS-V...

A Collision Avoidance Strategy for a Potential Natural Satellite around the Asteroid Bennu for the OSIRIS-REx Mission

NASA Technical Reports Server (NTRS)

Mashiku, Alinda K.; Carpenter, J. Russell

2016-01-01

The cadence of proximity operations for the OSIRIS-REx mission may have an extra induced challenge given the potential of the detection of a natural satellite orbiting the asteroid Bennu. Current ground radar observations for object detection orbiting Bennu show no found objects within bounds of specific size and rotation rates. If a natural satellite is detected during approach, a different proximity operation cadence will need to be implemented as well as a collision avoidance strategy for mission success. A collision avoidance strategy will be analyzed using the Wald Sequential Probability Ratio Test.

A Collision Avoidance Strategy for a Potential Natural Satellite Around the Asteroid Bennu for the OSIRIS-REx Mission

NASA Technical Reports Server (NTRS)

Mashiku, Alinda; Carpenter, Russell

2016-01-01

The cadence of proximity operations for the OSIRIS-REx mission may have an extra induced challenge given the potential of the detection of a natural satellite orbiting the asteroid Bennu. Current ground radar observations for object detection orbiting Bennu show no found objects within bounds of specific size and rotation rates. If a natural satellite is detected during approach, a different proximity operation cadence will need to be implemented as well as a collision avoidance strategy for mission success. A collision avoidance strategy will be analyzed using the Wald Sequential Probability Ratio Test.

Perceived threat and avoidance maneuvers in response to cockpit traffic displays

NASA Technical Reports Server (NTRS)

Smith, J. D.; Ellis, S. R.; Lee, E. C.

1984-01-01

Airline pilots rated their perception of the danger of an air-to-air collision based on cockpit displays of traffic information while they monitored simulated departures. They selected avoidance maneuvers when necessary for separation. Most evasive maneuvers were turns rather than vertical maneuvers. Evasive maneuvers chosen for encounters with lowor moderate-collision danger were generally toward the intruding aircraft. This tendency lessened as the perceived threat level increased. In the highest threat situations, pilots turned toward the intruder only at chance levels. Intruders coming from positions in front of the pilot's ship were more frequently avoided by turns toward than when intruders approached laterally or from behind. Some of the implications of the pilot's turning-toward tendencies are discussed with respect to automatic collision avoidance systems and coordination of avoidance maneuvers of conflicting aircraft.

Collision avoidance system cost-benefit analysis : volume III - appendices F-M

DOT National Transportation Integrated Search

1981-09-01

Collision-avoidance systems under development in the U.S.A., Japan and Germany were evaluated. The performance evaluation showed that the signal processing and the control law of a system were the key parameters that decided the system's capability, ...

Collision avoidance system cost-benefit analysis : volume II - appendices A-E

DOT National Transportation Integrated Search

1981-09-01

Collision-avoidance systems under development in the U.S.A., Japan and Germany were evaluated. The performance evaluation showed that the signal processing and the control law of a system were the key parameters that decided the system's capability, ...

Safety of High Speed Guided Ground Transportation Systems: Collision Avoidance and Accident Survivability Volume 4: Proposed Specifications

DOT National Transportation Integrated Search

1993-03-01

This report is the fourth of four volumes concerned with developing safety guidelines and specifications for high-speed : guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this : study ...

Safety of High Speed and Guided Ground Transportation Systems: Collision Avoidance and Accident Survivability: Volume 3

DOT National Transportation Integrated Search

1993-03-01

This report is the third of four volumes concerned with developing safety guidelines and specifications for high-speed : guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in : this study i...

System Capability Assessment of Cooperative Intersection Collision Avoidance System for Violations (CICAS-V)

DOT National Transportation Integrated Search

2011-07-01

This report describes the system capability assessment for the Cooperative Intersection Collision Avoidance System for Violations (CICAS-V) based on data collected from objective tests and a pilot test. The CICAS-V is a vehicle-to-infrastructure syst...

Automotive collision avoidance field operational test : warning cue implementation summary report

DOT National Transportation Integrated Search

2002-05-23

This report documents the human factors work conducted from January to June 2001 to design and evaluate the driver-vehicle-interface (DVI) for the Automotive Collision Avoidance System Field Operational Test (ACAS FOT) program. The objective was to d...

Coming back into the loop: Drivers' perceptual-motor performance in critical events after automated driving.

PubMed

Louw, Tyron; Markkula, Gustav; Boer, Erwin; Madigan, Ruth; Carsten, Oliver; Merat, Natasha

2017-11-01

This driving simulator study, conducted as part of the EU AdaptIVe project, investigated drivers' performance in critical traffic events, during the resumption of control from an automated driving system. Prior to the critical events, using a between-participant design, 75 drivers were exposed to various screen manipulations that varied the amount of available visual information from the road environment and automation state, which aimed to take them progressively further 'out-of-the-loop' (OoTL). The current paper presents an analysis of the timing, type, and rate of drivers' collision avoidance response, also investigating how these were influenced by the criticality of the unfolding situation. Results showed that the amount of visual information available to drivers during automation impacted on how quickly they resumed manual control, with less information associated with slower take-over times, however, this did not influence the timing of when drivers began a collision avoidance manoeuvre. Instead, the observed behaviour is in line with recent accounts emphasising the role of scenario kinematics in the timing of driver avoidance response. When considering collision incidents in particular, avoidance manoeuvres were initiated when the situation criticality exceeded an Inverse Time To Collision value of ≈0.3s -1 . Our results suggest that take-over time and timing and quality of avoidance response appear to be largely independent, and while long take-over time did not predict collision outcome, kinematically late initiation of avoidance did. Hence, system design should focus on achieving kinematically early avoidance initiation, rather than short take-over times. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analytical formulation of impulsive collision avoidance dynamics

NASA Astrophysics Data System (ADS)

Bombardelli, Claudio

2014-02-01

The paper deals with the problem of impulsive collision avoidance between two colliding objects in three dimensions and assuming elliptical Keplerian orbits. Closed-form analytical expressions are provided that accurately predict the relative dynamics of the two bodies in the encounter b-plane following an impulsive delta-V manoeuvre performed by one object at a given orbit location prior to the impact and with a generic three-dimensional orientation. After verifying the accuracy of the analytical expressions for different orbital eccentricities and encounter geometries the manoeuvre direction that maximises the miss distance is obtained numerically as a function of the arc length separation between the manoeuvre point and the predicted collision point. The provided formulas can be used for high-accuracy instantaneous estimation of the outcome of a generic impulsive collision avoidance manoeuvre and its optimisation.

Motor planning modulates sensory-motor control of collision avoidance behavior in the bullfrog, Rana catesbeiana

PubMed Central

Nakagawa, Hideki; Nishida, Yuuya

2012-01-01

Summary In this study, we examined the collision avoidance behavior of the frog, Rana catesbeiana to an approaching object in the upper visual field. The angular velocity of the frog's escape turn showed a significant positive correlation with the turn angle (r2 = 0.5741, P<0.05). A similar mechanism of velocity control has been known in head movements of the owl and in human saccades. By analogy, this suggests that the frog planned its escape velocity in advance of executing the turn, to make the duration of the escape behavior relatively constant. For escape turns less than 60°, the positive correlation was very strong (r2 = 0.7097, P<0.05). Thus, the frog controlled the angular velocity of small escape turns very accurately and completed the behavior within a constant time. On the other hand, for escape turns greater than 60°, the same correlation was not significant (r2 = 0.065, P>0.05). Thus, the frog was not able to control the velocity of the large escape turns accurately and did not complete the behavior within a constant time. In the latter case, there was a small but significant positive correlation between the threshold angular size and the angular velocity (r2 = 0.1459, P<0.05). This suggests that the threshold is controlled to compensate for the insufficient escape velocity achieved during large turn angles, and could explain a significant negative correlation between the turn angle and the threshold angular size (r2 = 0.1145, P<0.05). Thus, it is likely that the threshold angular size is also controlled by the turn angle and is modulated by motor planning. PMID:23213389

Opportunities and limitations for intersection collision intervention-A study of real world 'left turn across path' accidents.

PubMed

Sander, Ulrich

2017-02-01

Turning across the path of oncoming vehicle accidents are frequent and dangerous. To date not many car manufacturers have introduced Automated Emergency Braking (AEB) systems addressing this type of conflict situation, but it is foreseeable that these scenarios will be part of the Euro NCAP 2020 rating. Nine out of ten collisions are caused by the driver of the turning vehicle. An AEB system evaluating the ego and conflict vehicle driver's possibilities to avoid a pending crash by either braking or steering was specified for application in various constellations of vehicle collisions. In virtual simulation, AEB system parameters were varied, covering parameters that are relevant for driver comfort such as longitudinal and lateral acceleration (to define avoidance possibilities), expected steering maneuvers to avoid conflict, and intervention response characteristics (brake delay and ramp up) to assess the safety benefit. The reference simulation showed a potential of the AEB system in the turning vehicle to avoid approximately half of the collisions. An AEB system of the straight going vehicle was less effective. The effectiveness of the turning vehicle's AEB system increases if spatial limitations for the collision-avoidance steering maneuver are known. Such information could be provided by sensors detecting free space in or around the road environment or geographical information shared via vehicle to cloud communication. AEB interventions rarely result in collision avoidance for turning vehicles with speeds above 40km/h or for straight going vehicles with speeds above 60km/h. State of the art field-of-views of forward looking sensing systems designed for AEB rear-end interventions are capable of addressing turning across path situations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Safety of high-speed guided ground transportation systems : collision avoidance and accident survivability : volume 4 : proposed specifications

DOT National Transportation Integrated Search

1993-03-01

This report is the fourth of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is t...

Safety of high-speed guided ground transportation systems : collision avoidance and accident survivability : volume 3 : accident survivability

DOT National Transportation Integrated Search

1993-03-01

This report is the third of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is to...

Cooperative intersection collision avoidance system limited to stop sign and traffic signal violations (CICAS-V).

DOT National Transportation Integrated Search

2008-09-30

The objective of the Cooperative Intersection Collision Avoidance System for Violations (CICAS-V) Project is to develop and field-test a comprehensive system to reduce the number of crashes at intersections due to violations of traffic control device...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures - Task 4, Volume 2: RORSIM Manual

DOT National Transportation Integrated Search

1995-09-05

The Run-Off-Road Collision Avoidance Using IVHS Countermeasures program is to address the single vehicle crash problem through application of technology to prevent and/or reduce the severity of these crashes. : This report documents the RORSIM comput...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures, Task 3, Volume 2, Final Report

DOT National Transportation Integrated Search

1995-08-01

INTELLIGENT VEHICLE INITIATIVE OR IVI : THE RUN-OFF-ROAD COLLISION AVOIDANCE USING IVHS COUNTERMEASURES PROGRAM IS TO ADDRESS THE SINGLE VEHICLE CRASH PROBLEM THROUGH APPLICATION OF TECHNOLOGY TO PREVENT AND/OR REDUCE THE SEVERITY OF THESE CRASHES. :...

Evaluation of the Norridgewock intersection collision avoidance warning system on Route 201A, Norridgewock, Maine.

DOT National Transportation Integrated Search

2006-11-01

Review of the Norridgewock Intersection Collision Avoidance Warning System : demonstrates that the system appears to effectively reduce the number of potential : crashes at the intersection of River Road, Sophie May Lane and Route 201A. : Results sho...

Intersection Collision Avoidance Using Its Countermeasures. Task 9: Final Report: Intersection Collision Avoidance System Performance Guidelines

DOT National Transportation Integrated Search

2000-09-01

Roadway intersections are areas of potential conflict that increase risk exposure for vehicles attempting to pass through these locations. Advances in sensor and data processing technology during the past decade have enabled the collection of large a...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures: Task 3, Volume 1

DOT National Transportation Integrated Search

1995-08-23

The Run-Off-Road Collision Avoidance Using IVHS Countermeasures program is to address the single vehicle crash problem through application of technology to prevent and/or reduce the severity oi these crashes. This report describes the findings of the...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures Task 3 - Volume 2

DOT National Transportation Integrated Search

1995-08-23

The Run-Off-Road Collision Avoidance Using IVHS Countermeasures program is to address the single vehicle crash problem through application of technology to prevent and/or reduce the severity of these crashes. : This report describes the findings of t...

Error analysis in a stereo vision-based pedestrian detection sensor for collision avoidance applications.

PubMed

Llorca, David F; Sotelo, Miguel A; Parra, Ignacio; Ocaña, Manuel; Bergasa, Luis M

2010-01-01

This paper presents an analytical study of the depth estimation error of a stereo vision-based pedestrian detection sensor for automotive applications such as pedestrian collision avoidance and/or mitigation. The sensor comprises two synchronized and calibrated low-cost cameras. Pedestrians are detected by combining a 3D clustering method with Support Vector Machine-based (SVM) classification. The influence of the sensor parameters in the stereo quantization errors is analyzed in detail providing a point of reference for choosing the sensor setup according to the application requirements. The sensor is then validated in real experiments. Collision avoidance maneuvers by steering are carried out by manual driving. A real time kinematic differential global positioning system (RTK-DGPS) is used to provide ground truth data corresponding to both the pedestrian and the host vehicle locations. The performed field test provided encouraging results and proved the validity of the proposed sensor for being used in the automotive sector towards applications such as autonomous pedestrian collision avoidance.

Error Analysis in a Stereo Vision-Based Pedestrian Detection Sensor for Collision Avoidance Applications

PubMed Central

Llorca, David F.; Sotelo, Miguel A.; Parra, Ignacio; Ocaña, Manuel; Bergasa, Luis M.

2010-01-01

This paper presents an analytical study of the depth estimation error of a stereo vision-based pedestrian detection sensor for automotive applications such as pedestrian collision avoidance and/or mitigation. The sensor comprises two synchronized and calibrated low-cost cameras. Pedestrians are detected by combining a 3D clustering method with Support Vector Machine-based (SVM) classification. The influence of the sensor parameters in the stereo quantization errors is analyzed in detail providing a point of reference for choosing the sensor setup according to the application requirements. The sensor is then validated in real experiments. Collision avoidance maneuvers by steering are carried out by manual driving. A real time kinematic differential global positioning system (RTK-DGPS) is used to provide ground truth data corresponding to both the pedestrian and the host vehicle locations. The performed field test provided encouraging results and proved the validity of the proposed sensor for being used in the automotive sector towards applications such as autonomous pedestrian collision avoidance. PMID:22319323

Unmanned Aircraft Systems (UAS) Integration in the National Airspace System (NAS) Project: Advanced Collision Avoidance System for UAS (ACAS Xu) Interoperability White Paper Presentation

NASA Technical Reports Server (NTRS)

Fern, Lisa

2017-01-01

The Phase 1 DAA Minimum Operational Performance Standards (MOPS) provided requirements for two classes of DAA equipment: equipment Class 1 contains the basic DAA equipment required to assist a pilot in remaining well clear, while equipment Class 2 integrates the Traffic Alert and Collision Avoidance (TCAS) II system. Thus, the Class 1 system provides RWC functionality only, while the Class 2 system is intended to provide both RWC and Collision Avoidance (CA) functionality, in compliance with the Minimum Aviation System Performance (MASPS) for the Interoperability of Airborne Collision Avoidance Systems. The FAAs TCAS Program Office is currently developing Airborne Collision Avoidance System X (ACAS X) to support the objectives of the Federal Aviation Administrations (FAA) Next Generation Air Transportation System Program (NextGen). ACAS X has a suite of variants with a common underlying design that are intended to be optimized for their intended airframes and operations. ACAS Xu being is designed for UAS and allows for new surveillance technologies and tailored logic for platforms with different performance characteristics. In addition to Collision Avoidance (CA) alerting and guidance, ACAS Xu is being tuned to provide RWC alerting and guidance in compliance with the SC 228 DAA MOPS. With a single logic performing both RWC and CA functions, ACAS Xu will provide industry with an integrated DAA solution that addresses many of the interoperability shortcomings of Phase I systems. While the MOPS for ACAS Xu will specify an integrated DAA system, it will need to show compliance with the RWC alerting thresholds and alerting requirements defined in the DAA Phase 2 MOPS. Further, some functional components of the ACAS Xu system such as the remote pilots displayed guidance might be mostly references to the corresponding requirements in the DAA MOPS. To provide a seamless, integrated, RWC-CA system to assist the pilot in remaining well clear and avoiding collisions, several issues need to be addressed within the Phase 2 SC-228 DAA efforts. Interoperability of the RWC and CA alerting and guidance, and ensuring pilot comprehension, compliance and performance, will be a primary research area.

Optimised collision avoidance for an ultra-close rendezvous with a failed satellite based on the Gauss pseudospectral method

NASA Astrophysics Data System (ADS)

Chu, Xiaoyu; Zhang, Jingrui; Lu, Shan; Zhang, Yao; Sun, Yue

2016-11-01

This paper presents a trajectory planning algorithm to optimise the collision avoidance of a chasing spacecraft operating in an ultra-close proximity to a failed satellite. The complex configuration and the tumbling motion of the failed satellite are considered. The two-spacecraft rendezvous dynamics are formulated based on the target body frame, and the collision avoidance constraints are detailed, particularly concerning the uncertainties. An optimisation solution of the approaching problem is generated using the Gauss pseudospectral method. A closed-loop control is used to track the optimised trajectory. Numerical results are provided to demonstrate the effectiveness of the proposed algorithms.

Independent Evaluation of the Driver Acceptance of the Cooperative Intersection Collision Avoidance System for Violations (CICAS-V) Pilot Test

DOT National Transportation Integrated Search

2011-07-01

This report documents the results of the independent evaluations assessment of the driver acceptance of the Cooperative Intersection Collision Avoidance System limited to Stop Sign and Traffic Signal Violations (CICAS-V) system as tested during a ...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures Task 1 Vol. 1 Technical Findings

DOT National Transportation Integrated Search

1994-10-28

The Run-Off-Road Collision Avoidance Using IVHS Countermeasures program is to address the single vehicle crash problem through application of technology to prevent and/or reduce the severity of these crashes. This report describes and documents the a...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures, Task 1, Volume 1: Technical Findings, Final Report

DOT National Transportation Integrated Search

1994-10-01

THE RUN-OFF-ROAD COLLISION AVOIDANCE USING IVHS COUNTERMEASURES PROGRAM IS TO ADDRESS THE SINGLE VEHICLE CRASH PROBLEM THROUGH APPLICATION OF TECHNOLOGY TO PREVENT AND/OR REDUCE THE SEVERITY OF THESE CRASHES. : THIS REPORT DESCRIBES AND DOCUMENTS ...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures, Task 2, Volume 1: Technical Findings, Final Report

DOT National Transportation Integrated Search

1995-06-01

THE RUN-OFF-ROAD COLLISION AVOIDANCE USING IVHS COUNTERMEASURES PROGRAM IS TO ADDRESS THE SINGLE VEHICLE CRASH PROBLEM THROUGH APPLICATION OF TECHNOLOGY TO PREVENT AND/OR REDUCE THE SEVERITY OF THESE CRASHES. : THIS REPORT DESCRIBES AND DOCUMENTS ...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures, Task 4, Volume 2: Rorsim Manual, Final Report

DOT National Transportation Integrated Search

1995-09-01

THE RUN-OFF-ROAD COLLISION AVOIDANCE USING IVHS COUNTERMEASURES PROGRAM IS TO ADDRESS THE SINGLE VEHICLE CRASH PROBLEM THROUGH APPLICATION OF TECHNOLOGY TO PREVENT AND/OR REDUCE THE SEVERITY OF THESE CRASHES. : THIS REPORT DOCUMENTS THE RORSIM COM...

Run-Off Road Collision Avoidance Countermeasures Using IVHS Countermeasures Task 1 Vol. 2 Support Volume

DOT National Transportation Integrated Search

1994-10-28

The Run-Off-Road Collision Avoidance Using IVHS Countermeasures program is to address the single vehicle crash problem through application of technology to prevent and/or reduce the severity of these crashes. This report contains a summary of data us...

Operational Collision Avoidance

NASA Technical Reports Server (NTRS)

Guit, Bill

2015-01-01

This presentation will describe the early days of the EOS Aqua and Aura operational collision avoidance process. It will highlight EOS debris avoidance maneuvers, EOS high interest event statistic and A-Train systematic conjunctions and conclude with future challenges. This is related to earlier e-DAA (tracking number 21692) that an abstract was submitted to a different conference. Eric Moyer, ESMO Deputy Project Manager has reviewed and approved this presentation on May 6, 2015

LightForce photon-pressure collision avoidance: Efficiency analysis in the current debris environment and long-term simulation perspective

NASA Astrophysics Data System (ADS)

Yang Yang, Fan; Nelson, Bron; Aziz, Jonathan; Carlino, Roberto; Dono Perez, Andres; Faber, Nicolas; Foster, Cyrus; Frost, Chad; Henze, Chris; Karacalıoğlu, Arif Göktuğ; Levit, Creon; Marshall, William; Mason, James; O'Toole, Conor; Swenson, Jason; Worden, Simon P.; Stupl, Jan

2016-09-01

This work provides an efficiency analysis of the LightForce space debris collision avoidance scheme in the current debris environment and describes a simulation approach to assess its impact on the long-term evolution of the space debris environment. LightForce aims to provide just-in-time collision avoidance by utilizing photon pressure from ground-based industrial lasers. These ground stations impart minimal accelerations to increase the miss distance for a predicted conjunction between two objects. In the first part of this paper we will present research that investigates the short-term effect of a few systems consisting of 20 kW class lasers directed by 1.5 m diameter telescopes using adaptive optics. The results found such a network of ground stations to mitigate more than 85 percent of conjunctions and could lower the expected number of collisions in Low Earth Orbit (LEO) by an order of magnitude. While these are impressive numbers that indicate LightForce's utility in the short-term, the remaining 15 % of possible collisions contain (among others) conjunctions between two massive objects that would add large amount of debris if they collide. Still, conjunctions between massive objects and smaller objects can be mitigated. Hence, we choose to expand the capabilities of the simulation software to investigate the overall effect of a network of LightForce stations on the long-term debris evolution. In the second part of this paper, we will present the planned simulation approach for that effort. For the efficiency analysis of collision avoidance in the current debris environment, we utilize a simulation approach that uses the entire Two Line Element (TLE) catalog in LEO for a given day as initial input. These objects are propagated for one year and an all-on-all conjunction analysis is performed. For conjunctions that fall below a range threshold, we calculate the probability of collision and record those values. To assess efficiency, we compare a baseline (without collision avoidance) conjunction analysis with an analysis where LightForce is active. Using that approach, we take into account that collision avoidance maneuvers could have effects on third objects. Performing all-on-all conjunction analyses for extended period of time requires significant computer resources; hence we implemented this simulation utilizing a highly parallel approach on the NASA Pleiades supercomputer.

LightForce photon-pressure collision avoidance: Efficiency analysis in the current debris environment and long-term simulation perspective

PubMed Central

Yang, Fan Yang; Nelson, Bron; Aziz, Jonathan; Carlino, Roberto; Perez, Andres Dono; Faber, Nicolas; Foster, Cyrus; Frost, Chad; Henze, Chris; Karacalıoğlu, Arif Göktuğ; Levit, Creon; Marshall, William; Mason, James; O’Toole, Conor; Swenson, Jason; Worden, Simon P.; Stupl, Jan

2017-01-01

This work provides an efficiency analysis of the LightForce space debris collision avoidance scheme in the current debris environment and describes a simulation approach to assess its impact on the long-term evolution of the space debris environment. LightForce aims to provide just-in-time collision avoidance by utilizing photon pressure from ground-based industrial lasers. These ground stations impart minimal accelerations to increase the miss distance for a predicted conjunction between two objects. In the first part of this paper we will present research that investigates the short-term effect of a few systems consisting of 20 kW class lasers directed by 1.5 m diameter telescopes using adaptive optics. The results found such a network of ground stations to mitigate more than 85 percent of conjunctions and could lower the expected number of collisions in Low Earth Orbit (LEO) by an order of magnitude. While these are impressive numbers that indicate LightForce’s utility in the short-term, the remaining 15 % of possible collisions contain (among others) conjunctions between two massive objects that would add large amount of debris if they collide. Still, conjunctions between massive objects and smaller objects can be mitigated. Hence, we choose to expand the capabilities of the simulation software to investigate the overall effect of a network of LightForce stations on the long-term debris evolution. In the second part of this paper, we will present the planned simulation approach for that effort. For the efficiency analysis of collision avoidance in the current debris environment, we utilize a simulation approach that uses the entire Two Line Element (TLE) catalog in LEO for a given day as initial input. These objects are propagated for one year and an all-on-all conjunction analysis is performed. For conjunctions that fall below a range threshold, we calculate the probability of collision and record those values. To assess efficiency, we compare a baseline (without collision avoidance) conjunction analysis with an analysis where LightForce is active. Using that approach, we take into account that collision avoidance maneuvers could have effects on third objects. Performing all-on-all conjunction analyses for extended period of time requires significant computer resources; hence we implemented this simulation utilizing a highly parallel approach on the NASA Pleiades supercomputer. PMID:29302129

LightForce photon-pressure collision avoidance: Efficiency analysis in the current debris environment and long-term simulation perspective.

PubMed

Yang, Fan Yang; Nelson, Bron; Aziz, Jonathan; Carlino, Roberto; Perez, Andres Dono; Faber, Nicolas; Foster, Cyrus; Frost, Chad; Henze, Chris; Karacalıoğlu, Arif Göktuğ; Levit, Creon; Marshall, William; Mason, James; O'Toole, Conor; Swenson, Jason; Worden, Simon P; Stupl, Jan

2016-09-01

This work provides an efficiency analysis of the LightForce space debris collision avoidance scheme in the current debris environment and describes a simulation approach to assess its impact on the long-term evolution of the space debris environment. LightForce aims to provide just-in-time collision avoidance by utilizing photon pressure from ground-based industrial lasers. These ground stations impart minimal accelerations to increase the miss distance for a predicted conjunction between two objects. In the first part of this paper we will present research that investigates the short-term effect of a few systems consisting of 20 kW class lasers directed by 1.5 m diameter telescopes using adaptive optics. The results found such a network of ground stations to mitigate more than 85 percent of conjunctions and could lower the expected number of collisions in Low Earth Orbit (LEO) by an order of magnitude. While these are impressive numbers that indicate LightForce's utility in the short-term, the remaining 15 % of possible collisions contain (among others) conjunctions between two massive objects that would add large amount of debris if they collide. Still, conjunctions between massive objects and smaller objects can be mitigated. Hence, we choose to expand the capabilities of the simulation software to investigate the overall effect of a network of LightForce stations on the long-term debris evolution. In the second part of this paper, we will present the planned simulation approach for that effort. For the efficiency analysis of collision avoidance in the current debris environment, we utilize a simulation approach that uses the entire Two Line Element (TLE) catalog in LEO for a given day as initial input. These objects are propagated for one year and an all-on-all conjunction analysis is performed. For conjunctions that fall below a range threshold, we calculate the probability of collision and record those values. To assess efficiency, we compare a baseline (without collision avoidance) conjunction analysis with an analysis where LightForce is active. Using that approach, we take into account that collision avoidance maneuvers could have effects on third objects. Performing all-on-all conjunction analyses for extended period of time requires significant computer resources; hence we implemented this simulation utilizing a highly parallel approach on the NASA Pleiades supercomputer.

From Cannibalism to Active Motion of Groups

NASA Astrophysics Data System (ADS)

Romanczuk, Pawel; Schimansky-Geier, Lutz

2008-03-01

The detailed mechanisms leading to collective dynamics in groups of animals and insect are still poorly understood. A recent study by Simpson et. al. suggests cannibalism as a driving mechanism for coordinated migration of mormon crickets [1]. Based on this result we propose a simple generic model of brownian particles interacting by asymmetric, non-conservative collisions accounting for cannibalistic behavior and the corresponding avoidance strategy. We discuss our model in one and two dimensions and show that a certain type of collisions drives the system out of equilibrium and leads to coordinated active motion of groups.[1] Stephen J. Simpson, Gregory A. Sword, Patrick D. Lorch and Iain D. Couzin: Cannibal crickets on a forced march for protein and salt, PNAS, 103:4152-4156, 2006

TU-FG-201-07: Development of SRS Conical Collimator Collision Prediction Software for Radiation Treatment Safety

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gutti, V; Morrow, A; Kim, S

Purpose: Stereotactic radiosurgery (SRS) treatments using conical collimators can potentially result in gantry collision with treatment table due to limited collision-clear spaces. An in-house software was developed to help the SRS treatment planner mitigate potential SRS conical collimator (Varian Medical System, Palo Alto, CA) collisions with the treatment table. This software was designed to remove treatment re-planning secondary to unexpected collisions. Methods: A BrainLAB SRS ICT Frameless Extension used for SRS treatments in our clinic was mathematically modelled using surface points registered to the 3D co-ordinate space of the couch extension. The surface points are transformed based on the treatmentmore » isocenter point and potential collisions are determined in 3D space for couch and gantry angle combinations. The distance between the SRS conical collimators and LINAC isocenter is known. The collision detection model was programmed in MATLAB (Mathwork, Natick, MA) to display graphical plots of the calculations, and the plotted data is used to avoid the gantry and couch angle combinations that would likely result in a collision. We have utilized the cone collision tool for 23 SRS cone treatment plans (8 retrospective and 15 prospective for 10 patients). Results: Twenty one plans strongly agreed with the software tool prediction for collision. However, in two plans, a collision was observed with a 0.5 cm margin when the software predicted no collision. Therefore, additional margins were added to the clearance criteria in the program to achieve a lower risk of actual collisions. Conclusion: Our in-house developed collision check software successfully avoided SRS cone re-planning by 91.3% due to a reduction in cone collisions with the treatment table. Future developments to our software will include a CT image data set based collision prediction model as well as a beam angle optimization tool to avoid normal critical tissues as well as previously treated lesions.« less

Development of performance specifications for collision avoidance systems for lane change crashes. Task 6, interim report : testbed systems design and associated facilities

DOT National Transportation Integrated Search

2001-11-01

This report documents the design of an on-road testbed vehicle. The purposes of this testbed are twofold: (1) Establish a foundation for estimating lane change collision avoidance effectiveness, and (2) provide information pertinent to setting perfor...

A Receiver-Initiated Collision-Avoidance Protocol for Multi-Channel Networks

DTIC Science & Technology

2001-01-01

00-00-2001 to 00-00-2001 4. TITLE AND SUBTITLE A Receiver-Initiated Collision-Avoidance Protocol for Multi-Channel Netowrks 5a. CONTRACT NUMBER...images. 14. ABSTRACT 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 18. NUMBER OF PAGES 10 19a. NAME OF RESPONSIBLE

33 CFR 83.08 - Action to avoid collision (Rule 8).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Action to avoid collision (Rule 8). 83.08 Section 83.08 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES RULES Steering and Sailing Rules Conduct of Vessels in Any Condition of...

33 CFR 83.08 - Action to avoid collision (Rule 8).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Action to avoid collision (Rule 8). 83.08 Section 83.08 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES RULES Steering and Sailing Rules Conduct of Vessels in Any Condition of...

33 CFR 83.08 - Action to avoid collision (Rule 8).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Action to avoid collision (Rule 8). 83.08 Section 83.08 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES RULES Steering and Sailing Rules Conduct of Vessels in Any Condition of...

33 CFR 83.08 - Action to avoid collision (Rule 8).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Action to avoid collision (Rule 8). 83.08 Section 83.08 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES RULES Steering and Sailing Rules Conduct of Vessels in Any Condition of...

33 CFR 83.08 - Action to avoid collision (Rule 8).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Action to avoid collision (Rule 8). 83.08 Section 83.08 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES RULES Steering and Sailing Rules Conduct of Vessels in Any Condition of...

A Detailed Study of Advection Sea Fog Formation to Reduce the Operational Impacts Along the Northern Gulf of Mexico

DTIC Science & Technology

2007-03-01

From Mid-Air Collision Avoidance Pilot Education Program, Tyndall Air Force Base. http://www.tyndall.af.mil/ MACA /moamap.pdf Accessed 10 September...Collision Avoidance Pilot Education Program, Tyndall Air Force Base. http://www.tyndall.af.mil/ MACA /moamap.pdf Accessed 10 September 2006). 5...cited 2006: Tyndall Air Force Base. [Available online at http://www.tyndall.af.mil/ MACA /moamap.pdf]. Accessed 25 September 2006. Mid-Air Collision

The design of a minimal sensor configuration for a Cooperative Intersection Collision Avoidance System - Stop Sign Assist : (CICAS-SSA report #2).

DOT National Transportation Integrated Search

2010-08-01

The deployment of a Cooperative Intersection Collision Avoidance System Stop Sign Assist (CICAS-SSA) can save lives by addressing the causal factor of crashes at rural thru-Stop intersection: drivers who stop on the minor leg of the intersection,...

Development of performance specifications for collision avoidance systems for lane change, merging, and backing. Task 6, Interim report : testbed systems design and associated facilities

DOT National Transportation Integrated Search

1997-05-01

This report represents the documentation of the design of the testbed. The purposes of the testbed are twofold 1) Establish a foundation for estimating collision avoidance effectiveness and 2) Provide information pertinent to setting performance spec...

Obstacle avoidance in social groups: new insights from asynchronous models

PubMed Central

Croft, Simon; Budgey, Richard; Pitchford, Jonathan W.; Wood, A. Jamie

2015-01-01

For moving animals, the successful avoidance of hazardous obstacles is an important capability. Despite this, few models of collective motion have addressed the relationship between behavioural and social features and obstacle avoidance. We develop an asynchronous individual-based model for social movement which allows social structure within groups to be included. We assess the dynamics of group navigation and resulting collision risk in the context of information transfer through the system. In agreement with previous work, we find that group size has a nonlinear effect on collision risk. We implement examples of possible network structures to explore the impact social preferences have on collision risk. We show that any social heterogeneity induces greater obstacle avoidance with further improvements corresponding to groups containing fewer influential individuals. The model provides a platform for both further theoretical investigation and practical application. In particular, we argue that the role of social structures within bird flocks may have an important role to play in assessing the risk of collisions with wind turbines, but that new methods of data analysis are needed to identify these social structures. PMID:25833245

Design and hardware-in-loop implementation of collision avoidance algorithms for heavy commercial road vehicles

NASA Astrophysics Data System (ADS)

Rajaram, Vignesh; Subramanian, Shankar C.

2016-07-01

An important aspect from the perspective of operational safety of heavy road vehicles is the detection and avoidance of collisions, particularly at high speeds. The development of a collision avoidance system is the overall focus of the research presented in this paper. The collision avoidance algorithm was developed using a sliding mode controller (SMC) and compared to one developed using linear full state feedback in terms of performance and controller effort. Important dynamic characteristics such as load transfer during braking, tyre-road interaction, dynamic brake force distribution and pneumatic brake system response were considered. The effect of aerodynamic drag on the controller performance was also studied. The developed control algorithms have been implemented on a Hardware-in-Loop experimental set-up equipped with the vehicle dynamic simulation software, IPG/TruckMaker®. The evaluation has been performed for realistic traffic scenarios with different loading and road conditions. The Hardware-in-Loop experimental results showed that the SMC and full state feedback controller were able to prevent the collision. However, when the discrepancies in the form of parametric variations were included, the SMC provided better results in terms of reduced stopping distance and lower controller effort compared to the full state feedback controller.

Visuo-motor coordination and internal models for object interception.

PubMed

Zago, Myrka; McIntyre, Joseph; Senot, Patrice; Lacquaniti, Francesco

2009-02-01

Intercepting and avoiding collisions with moving objects are fundamental skills in daily life. Anticipatory behavior is required because of significant delays in transforming sensory information about target and body motion into a timed motor response. The ability to predict the kinematics and kinetics of interception or avoidance hundreds of milliseconds before the event may depend on several different sources of information and on different strategies of sensory-motor coordination. What are exactly the sources of spatio-temporal information and what are the control strategies remain controversial issues. Indeed, these topics have been the battlefield of contrasting views on how the brain interprets visual information to guide movement. Here we attempt a synthetic overview of the vast literature on interception. We discuss in detail the behavioral and neurophysiological aspects of interception of targets falling under gravity, as this topic has received special attention in recent years. We show that visual cues alone are insufficient to predict the time and place of interception or avoidance, and they need to be supplemented by prior knowledge (or internal models) about several features of the dynamic interaction with the moving object.

LightForce Photon-Pressure Collision Avoidance: Efficiency Assessment on an Entire Catalogue of Space Debris

NASA Technical Reports Server (NTRS)

Stupl, Jan Michael; Faber, Nicolas; Foster, Cyrus; Yang Yang, Fan; Levit, Creon

2013-01-01

The potential to perturb debris orbits using photon pressure from ground-based lasers has been confirmed by independent research teams. Two useful applications of this scheme are protecting space assets from impacts with debris and stabilizing the orbital debris environment, both relying on collision avoidance rather than de-orbiting debris. This paper presents the results of a new assessment method to analyze the efficiency of the concept for collision avoidance. Earlier research concluded that one ground based system consisting of a 10 kW class laser, directed by a 1.5 m telescope with adaptive optics, can prevent a significant fraction of debris-debris collisions in low Earth orbit. That research used in-track displacement to measure efficiency and restricted itself to an analysis of a limited number of objects. As orbit prediction error is dependent on debris object properties, a static displacement threshold should be complemented with another measure to assess the efficiency of the scheme. In this paper we present the results of an approach using probability of collision. Using a least-squares fitting method, we improve the quality of the original TLE catalogue in terms of state and co-state accuracy. We then calculate collision probabilities for all the objects in the catalogue. The conjunctions with the highest risk of collision are then engaged by a simulated network of laser ground stations. After those engagements, the perturbed orbits are used to re-assess the collision probability in a 20 minute window around the original conjunction. We then use different criteria to evaluate the utility of the laser-based collision avoidance scheme and assess the number of base-line ground stations needed to mitigate a significant number of high probability conjunctions. Finally, we also give an account how a laser ground station can be used for both orbit deflection and debris tracking.

Collision avoidance in space

NASA Technical Reports Server (NTRS)

Kessler, D. J.; Cour-Palais, B. G.; Taylor, R. E.; Landry, P. M.

1980-01-01

Collisions in earth orbital space between operational payloads and various forms of space debris (nonoperational payloads, nonfunctional mission-related objects and fragments resulting from collisions and explosions) are discussed and possible means of avoiding them are considered. From 10,000 to 15,000 objects are estimated to be in earth orbital space, most of which represent spacecraft fragments and debris too small to be detected and tracked by earth-based sensors, and it is considered likely that some of them will be or have already been involved in direct collisions with the ever increasing number of operational satellites and space stations. Means of protecting proposed large space structures and smaller spacecraft from significant damage by larger space objects, particularly in the 400-4000 km altitude range where most debris occurs, include structural redundancy and the double shielding of sensitive components. Other means of collision avoidance are the collection or relocation of satellites, rocket bodies and other objects by the Space Shuttle, the prevention of explosions and the disposal of spent rocket parts by reentry. Finally, a management structure would be required to administer guidelines for the prevention and elimination of space debris.

Volvo and Infiniti drivers' experiences with select crash avoidance technologies.

PubMed

Braitman, Keli A; McCartt, Anne T; Zuby, David S; Singer, Jeremiah

2010-06-01

Vehicle-based crash avoidance systems can potentially reduce crashes, but success depends on driver acceptance and understanding. This study gauged driver use, experience, and acceptance among early adopters of select technologies. Telephone interviews were conducted in early 2009 with 380 owners of Volvo vehicles equipped with forward collision warning with autobrake, lane departure warning, side-view assist, and/or active bi-xenon headlights and 485 owners of Infiniti vehicles with lane departure warning/prevention. Most owners kept systems turned on most of the time, especially forward collision warning with autobrake and side-view assist. The exception was lane departure prevention; many owners were unaware they had it, and the system must be activated each time the vehicle is started. Most owners reported being safer with the technologies and would want them again on their next vehicles. Perceived false or unnecessary warnings were fairly common, particularly with side-view assist. Some systems were annoying, especially lane departure warning. Many owners reported safer driving behaviors such as greater use of turn signals (lane departure warning), increased following distance (forward collision warning), and checking side mirrors more frequently (side-view assist), but some reported driving faster at night (active headlights). Despite some unnecessary or annoying warnings, most Volvo and Infiniti owners use crash avoidance systems most of the time. Among early adopters, the first requirement of effective warning systems (that owners use the technology) seems largely met. Systems requiring activation by drivers for each trip are used less often. Owner experience with the latest technologies from other automobile manufacturers should be studied, as well as for vehicles on which technologies are standard (versus optional) equipment. The effectiveness of technologies in preventing and mitigating crashes and injuries, and user acceptance of interfaces, should be examined as more vehicles with advanced technologies penetrate the fleet.

Passive Collision Avoidance System for UAS

DTIC Science & Technology

2008-09-01

feasibility of using SWAP efficient LWIR microbolometers as outlined in the Priest report circa 1998 as a solution to the collision avoidance problems for UASs...81 7.3 LWIR Multispectral Sensor ..........................................................................................84 7.4 LWIR ... LWIR image of the Ultralight. Muffler runs at approximately 1200 F. ......................32 Figure 36: 3D model of LVDS circuit board with L-3

Calibration, Information, and Control Strategies for Braking to Avoid a Collision

ERIC Educational Resources Information Center

Fajen, Brett R.

2005-01-01

This study explored visual control strategies for braking to avoid collision by manipulating information about speed of self-motion. Participants watched computer-generated displays and used a brake to stop at an object in the path of motion. Global optic flow rate and edge rate were manipulated by adjusting eyeheight and ground-texture size.…

CAESAR, French Probative Public Service for In-Orbit Collision Avoidance

NASA Astrophysics Data System (ADS)

Laporte, Francois; Moury, Monique

2013-08-01

This paper starts by describing the conjunction analysis which has to be performed using CSM data provided by JSpOC. This description not only demonstrates that Collision Avoidance is a 2-step process (close approach detection followed by risk evaluation for collision avoidance decision) but also leads to the conclusion that there is a need for Middle Man role. After describing the Middle Man concept, it introduces the French response CAESAR and the need for collaborative work environment which is implied by Middle Man concept. It includes a description of the environment put in place for CAESAR (secure website and dedicated tools), the content of the service, the condition for the distribution of the CNES software JAC and the advantages for subscribers.

The effect of collision avoidance for autonomous robot team formation

NASA Astrophysics Data System (ADS)

Seidman, Mark H.; Yang, Shanchieh J.

2007-04-01

As technology and research advance to the era of cooperative robots, many autonomous robot team algorithms have emerged. Shape formation is a common and critical task in many cooperative robot applications. While theoretical studies of robot team formation have shown success, it is unclear whether such algorithms will perform well in a real-world environment. This work examines the effect of collision avoidance schemes on an ideal circle formation algorithm, but behaves similarly if robot-to-robot communications are in place. Our findings reveal that robots with basic collision avoidance capabilities are still able to form into a circle, under most conditions. Moreover, the robot sizes, sensing ranges, and other critical physical parameters are examined to determine their effects on algorithm's performance.

Sense-and-Avoid Equivalent Level of Safety Definition for Unmanned Aircraft Systems. Revision 9

NASA Technical Reports Server (NTRS)

2005-01-01

Since unmanned aircraft do not have a pilot on-board the aircraft, they cannot literally comply with the "see and avoid" requirement beyond a short distance from the location of the unmanned pilot. No performance standards are presently defined for unmanned Sense and Avoid systems, and the FAA has no published approval criteria for a collision avoidance system. Before the FAA can develop the necessary guidance (rules / regulations / policy) regarding the see-and-avoid requirements for Unmanned Aircraft Systems (UAS), a concise understanding of the term "equivalent level of safety" must be attained. Since this term is open to interpretation, the UAS industry and FAA need to come to an agreement on how this term can be defined and applied for a safe and acceptable collision avoidance capability for unmanned aircraft. Defining an equivalent level of safety (ELOS) for sense and avoid is one of the first steps in understanding the requirement and developing a collision avoidance capability. This document provides a functional level definition of see-and-avoid as it applies to unmanned aircraft. The sense and avoid ELOS definition is intended as a bridge between the see and avoid requirement and the system level requirements for unmanned aircraft sense and avoid systems. Sense and avoid ELOS is defined in a rather abstract way, meaning that it is not technology or system specific, and the definition provides key parameters (and a context for those parameters) to focus the development of cooperative and non-cooperative sense and avoid system requirements.

Evaluation of minimum coverage size and orbital accuracy at different orbital regimes for one order of magnitude reduction of the catastrophic collision risk

NASA Astrophysics Data System (ADS)

Sánchez-Ortiz, Noelia; Domínguez-González, Raúl; Krag, Holger

2015-03-01

One of the main objectives of Space Surveillance and Tracking (SST) systems is to support space collision avoidance activities. This collision avoidance capability aims to significantly reduce the catastrophic collision risk of space objects. In particular, for the case of the future European SST, the objective is translated into a risk reduction of one order of magnitude whilst keeping a low number of false alarm events. In order to translate this aim into system requirements, an evaluation of the current catastrophic collision risk for different orbital regimes is addressed. The reduction of such risk depends on the amount of catalogued objects (coverage) and the knowledge of the associated orbits in the catalogue (accuracy). This paper presents an analysis of the impact of those two aspects in the capability to reduce the catastrophic collision risk at some orbital regimes. A reliable collision avoidance support depends on the accuracy of the predicted miss-events. The assessment of possible conjunctions is normally done by computing the estimated miss-distances between objects (which is compared with a defined distance threshold) or by computing the associated collision risk (which is compared with the corresponding accepted collision probability level). This second method is normally recommended because it takes into account the reliability of the orbits and allows reducing false alarm events. The collision risk depends on the estimated miss-distance, the object sizes and the accuracy of the two orbits at the time of event. This accuracy depends on the error of the orbits at the orbit determination epoch and the error derived from the propagation from that epoch up to the time of event. The modified DRAMA ARES (Domínguez-González et al., 2012, 2013a,b; Gelhaus et al., 2014) provides information on the expected number of encounters for a given mission and year. It also provides information on the capacity to reduce the risk of collision by means of avoidance manoeuvres as a function of the accepted collision probability level and the cataloguing performance of the surveillance system (determined by the limiting coverage size-altitude function and the orbital data accuracy). The assessment of avoidance strategies takes into account statistical models of the space object environment, as provided by ESA's MASTER-2009 model, and a mathematical framework for the collision risk estimation as used in satellite operations. In this papers, results are provided for some orbit types, covering different orbital regimes. The analysis is done for different cataloguing capacity levels (accuracy and coverage), concluding that 5 cm are to be covered at LEO for diminishing the catastrophic collision risk by one order of magnitude. For MEO and GEO regime, coverage down to 40 and 100 cm respectively allow similar reduction of risk.

How to quantitatively evaluate safety of driver behavior upon accident? A biomechanical methodology

PubMed Central

Zhang, Wen; Cao, Jieer

2017-01-01

How to evaluate driver spontaneous reactions in various collision patterns in a quantitative way is one of the most important topics in vehicle safety. Firstly, this paper constructs representative numerical crash scenarios described by impact velocity, impact angle and contact position based on finite element (FE) computation platform. Secondly, a driver cabin model is extracted and described in the well validated multi-rigid body (MB) model to compute the value of weighted injury criterion to quantitatively assess drivers’ overall injury under certain circumstances. Furthermore, based on the coupling of FE and MB, parametric studies on various crash scenarios are conducted. It is revealed that the WIC (Weighted Injury Criteria) value variation law under high impact velocities is quite distinct comparing with the one in low impact velocities. In addition, the coupling effect can be elucidated by the fact that the difference of WIC value among three impact velocities under smaller impact angles tends to be distinctly higher than that under larger impact angles. Meanwhile, high impact velocity also increases the sensitivity of WIC under different collision positions and impact angles. Results may provide a new methodology to quantitatively evaluate driving behaviors and serve as a significant guiding step towards collision avoidance for autonomous driving vehicles. PMID:29240789

How to quantitatively evaluate safety of driver behavior upon accident? A biomechanical methodology.

PubMed

Zhang, Wen; Cao, Jieer; Xu, Jun

2017-01-01

How to evaluate driver spontaneous reactions in various collision patterns in a quantitative way is one of the most important topics in vehicle safety. Firstly, this paper constructs representative numerical crash scenarios described by impact velocity, impact angle and contact position based on finite element (FE) computation platform. Secondly, a driver cabin model is extracted and described in the well validated multi-rigid body (MB) model to compute the value of weighted injury criterion to quantitatively assess drivers' overall injury under certain circumstances. Furthermore, based on the coupling of FE and MB, parametric studies on various crash scenarios are conducted. It is revealed that the WIC (Weighted Injury Criteria) value variation law under high impact velocities is quite distinct comparing with the one in low impact velocities. In addition, the coupling effect can be elucidated by the fact that the difference of WIC value among three impact velocities under smaller impact angles tends to be distinctly higher than that under larger impact angles. Meanwhile, high impact velocity also increases the sensitivity of WIC under different collision positions and impact angles. Results may provide a new methodology to quantitatively evaluate driving behaviors and serve as a significant guiding step towards collision avoidance for autonomous driving vehicles.

Pilot Non-Conformance to Alerting System Commands During Closely Spaced Parallel Approaches

NASA Technical Reports Server (NTRS)

Pritchett, Amy R.; Hansman, R. John

1997-01-01

Pilot non-conformance to alerting system commands has been noted in general and to a TCAS-like collision avoidance system in a previous experiment. This paper details two experiments studying collision avoidance during closely-spaced parallel approaches in instrument meteorological conditions (IMC), and specifically examining possible causal factors of, and design solutions to, pilot non-conformance.

Application of radar for automotive collision avoidance. Volume 1: Technical report

NASA Technical Reports Server (NTRS)

Lichtenberg, C. L. (Editor)

1987-01-01

The purpose of this project was research and development of an automobile collision avoidance radar system. The major finding was that the application of radar to the automobile collision avoidance problem deserves continued research even though the specific approach investigated in this effort did not perform adequately in its angle measurement capability. Additional findings were that: (1) preliminary performance requirements of a candidate radar system are not unreasonable; (2) the number and severity of traffic accidents could be reduced by using a collision avoidance radar system which observes a fairly wide (at least + or - 10 deg) field of view ahead of the vehicle; (3) the health radiation hazards of a probable radar design are not significant even when a large number of radar-equipped vehicles are considered; (4) effects of inclement weather on radar operation can be accommodated in most cases; (5) the phase monopulse radar technique as implemented demonstrated inferior angle measurement performance which warrants the recommendation of investigating alternative radar techniques; and (6) extended target and multipath effects, which presumably distort the amplitude and phase distribution across the antenna aperture, are responsible for the observed inadequate phase monopulse radar performance.

Radar sensors for intersection collision avoidance

NASA Astrophysics Data System (ADS)

Jocoy, Edward H.; Phoel, Wayne G.

1997-02-01

On-vehicle sensors for collision avoidance and intelligent cruise control are receiving considerably attention as part of Intelligent Transportation Systems. Most of these sensors are radars and `look' in the direction of the vehicle's headway, that is, in the direction ahead of the vehicle. Calspan SRL Corporation is investigating the use of on- vehicle radar for Intersection Collision Avoidance (ICA). Four crash scenarios are considered and the goal is to design, develop and install a collision warning system in a test vehicle, and conduct both test track and in-traffic experiments. Current efforts include simulations to examine ICA geometry-dependent design parameters and the design of an on-vehicle radar and tracker for threat detection. This paper discusses some of the simulation and radar design efforts. In addition, an available headway radar was modified to scan the wide angles (+/- 90 degree(s)) associated with ICA scenarios. Preliminary proof-of-principal tests are underway as a risk reduction effort. Some initial target detection results are presented.

Numerical approach of collision avoidance and optimal control on robotic manipulators

NASA Technical Reports Server (NTRS)

Wang, Jyhshing Jack

1990-01-01

Collision-free optimal motion and trajectory planning for robotic manipulators are solved by a method of sequential gradient restoration algorithm. Numerical examples of a two degree-of-freedom (DOF) robotic manipulator are demonstrated to show the excellence of the optimization technique and obstacle avoidance scheme. The obstacle is put on the midway, or even further inward on purpose, of the previous no-obstacle optimal trajectory. For the minimum-time purpose, the trajectory grazes by the obstacle and the minimum-time motion successfully avoids the obstacle. The minimum-time is longer for the obstacle avoidance cases than the one without obstacle. The obstacle avoidance scheme can deal with multiple obstacles in any ellipsoid forms by using artificial potential fields as penalty functions via distance functions. The method is promising in solving collision-free optimal control problems for robotics and can be applied to any DOF robotic manipulators with any performance indices and mobile robots as well. Since this method generates optimum solution based on Pontryagin Extremum Principle, rather than based on assumptions, the results provide a benchmark against which any optimization techniques can be measured.

Virtual reality-based navigation task to reveal obstacle avoidance performance in individuals with visuospatial neglect.

PubMed

Aravind, Gayatri; Darekar, Anuja; Fung, Joyce; Lamontagne, Anouk

2015-03-01

Persons with post-stroke visuospatial neglect (VSN) often collide with moving obstacles while walking. It is not well understood whether the collisions occur as a result of attentional-perceptual deficits caused by VSN or due to post-stroke locomotor deficits. We assessed individuals with VSN on a seated, joystick-driven obstacle avoidance task, thus eliminating the influence of locomotion. Twelve participants with VSN were tested on obstacle detection and obstacle avoidance tasks in a virtual environment that included three obstacles approaching head-on or 30 (°) contralesionally/ipsilesionally. Our results indicate that in the detection task, the contralesional and head-on obstacles were detected at closer proximities compared to the ipsilesional obstacle. For the avoidance task collisions were observed only for the contralesional and head-on obstacle approaches. For the contralesional obstacle approach, participants initiated their avoidance strategies at smaller distances from the obstacle and maintained smaller minimum distances from the obstacles. The distance at detection showed a negative association with the distance at the onset of avoidance strategy for all three obstacle approaches. We conclusion the observation of collisions with contralesional and head-on obstacles, in the absence of locomotor burden, provides evidence that attentional-perceptual deficits due to VSN, independent of post-stroke locomotor deficits, alter obstacle avoidance abilities.

Difference between car-to-cyclist crash and near crash in a perpendicular crash configuration based on driving recorder analysis.

PubMed

Ito, Daisuke; Hayakawa, Kosei; Kondo, Yuma; Mizuno, Koji; Thomson, Robert; Piccinini, Giulio Bianchi; Hosokawa, Naruyuki

2018-08-01

Analyzing a crash using driving recorder data makes it possible to objectively examine factors contributing to the occurrence of the crash. In this study, car-to-cyclist crashes and near crashes recorded on cars equipped with advanced driving recorders were compared with each other in order to examine the factors that differentiate near crashes from crashes, as well as identify the causes of the crashes. Focusing on cases where the car and cyclist approached each other perpendicularly, the differences in the car's and cyclist's parameters such as velocity, distance and avoidance behavior were analyzed. The results show that car-to-cyclist crashes would not be avoidable when the car approaching the cyclist enters an area where the average deceleration required to stop the car is more than 0.45 G (4.4 m/s 2 ). In order for this situation to occur, there are two types of cyclist crash scenarios. In the first scenario, the delay in the drivers' reaction in activating the brakes is the main factor responsible for the crash. In this scenario, time-to-collision when the cyclist first appears in the video is more than 2.0 s. In the second scenario, the sudden appearance of a cyclist from behind an obstacle on the street is the factor responsible for the crash. In this case, the time-to-collision is less than 1.2 s, and the crash cannot be avoided even if the driver exhibited avoidance maneuvers. Copyright © 2018 Elsevier Ltd. All rights reserved.

Visual control of foot placement when walking over complex terrain.

PubMed

Matthis, Jonathan S; Fajen, Brett R

2014-02-01

The aim of this study was to investigate the role of visual information in the control of walking over complex terrain with irregularly spaced obstacles. We developed an experimental paradigm to measure how far along the future path people need to see in order to maintain forward progress and avoid stepping on obstacles. Participants walked over an array of randomly distributed virtual obstacles that were projected onto the floor by an LCD projector while their movements were tracked by a full-body motion capture system. Walking behavior in a full-vision control condition was compared with behavior in a number of other visibility conditions in which obstacles did not appear until they fell within a window of visibility centered on the moving observer. Collisions with obstacles were more frequent and, for some participants, walking speed was slower when the visibility window constrained vision to less than two step lengths ahead. When window sizes were greater than two step lengths, the frequency of collisions and walking speed were weakly affected or unaffected. We conclude that visual information from at least two step lengths ahead is needed to guide foot placement when walking over complex terrain. When placed in the context of recent research on the biomechanics of walking, the findings suggest that two step lengths of visual information may be needed because it allows walkers to exploit the passive mechanical forces inherent to bipedal locomotion, thereby avoiding obstacles while maximizing energetic efficiency. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Evaluation of a Portable Collision Warning Device for Patients With Peripheral Vision Loss in an Obstacle Course.

PubMed

Pundlik, Shrinivas; Tomasi, Matteo; Luo, Gang

2015-04-01

A pocket-sized collision warning device equipped with a video camera was developed to predict impending collisions based on time to collision rather than proximity. A study was conducted in a high-density obstacle course to evaluate the effect of the device on collision avoidance in people with peripheral field loss (PFL). The 41-meter-long loop-shaped obstacle course consisted of 46 stationary obstacles from floor to head level and oncoming pedestrians. Twenty-five patients with tunnel vision (n = 13) or hemianopia (n = 12) completed four consecutive loops with and without the device, while not using any other habitual mobility aid. Walking direction and device usage order were counterbalanced. Number of collisions and preferred percentage of walking speed (PPWS) were compared within subjects. Collisions were reduced significantly by approximately 37% (P < 0.001) with the device (floor-level obstacles were excluded because the device was not designed for them). No patient had more collisions when using the device. Although the PPWS were also reduced with the device from 52% to 49% (P = 0.053), this did not account for the lower number of collisions, as the changes in collisions and PPWS were not correlated (P = 0.516). The device may help patients with a wide range of PFL avoid collisions with high-level obstacles while barely affecting their walking speed.

Conservative bin-to-bin fractional collisions

NASA Astrophysics Data System (ADS)

Martin, Robert

2016-11-01

Particle methods such as direct simulation Monte Carlo (DSMC) and particle-in-cell (PIC) are commonly used to model rarefied kinetic flows for engineering applications because of their ability to efficiently capture non-equilibrium behavior. The primary drawback to these methods relates to the poor convergence properties due to the stochastic nature of the methods which typically rely heavily on high degrees of non-equilibrium and time averaging to compensate for poor signal to noise ratios. For standard implementations, each computational particle represents many physical particles which further exacerbate statistical noise problems for flow with large species density variation such as encountered in flow expansions and chemical reactions. The stochastic weighted particle method (SWPM) introduced by Rjasanow and Wagner overcome this difficulty by allowing the ratio of real to computational particles to vary on a per particle basis throughout the flow. The DSMC procedure must also be slightly modified to properly sample the Boltzmann collision integral accounting for the variable particle weights and to avoid the creation of additional particles with negative weight. In this work, the SWPM with necessary modification to incorporate the variable hard sphere (VHS) collision cross section model commonly used in engineering applications is first incorporated into an existing engineering code, the Thermophysics Universal Research Framework. The results and computational efficiency are compared to a few simple test cases using a standard validated implementation of the DSMC method along with the adapted SWPM/VHS collision using an octree based conservative phase space reconstruction. The SWPM method is then further extended to combine the collision and phase space reconstruction into a single step which avoids the need to create additional computational particles only to destroy them again during the particle merge. This is particularly helpful when oversampling the collision integral when compared to the standard DSMC method. However, it is found that the more frequent phase space reconstructions can cause added numerical thermalization with low particle per cell counts due to the coarseness of the octree used. However, the methods are expected to be of much greater utility in transient expansion flows and chemical reactions in the future.

Interaction dynamics of multiple mobile robots with simple navigation strategies

NASA Technical Reports Server (NTRS)

Wang, P. K. C.

1989-01-01

The global dynamic behavior of multiple interacting autonomous mobile robots with simple navigation strategies is studied. Here, the effective spatial domain of each robot is taken to be a closed ball about its mass center. It is assumed that each robot has a specified cone of visibility such that interaction with other robots takes place only when they enter its visibility cone. Based on a particle model for the robots, various simple homing and collision-avoidance navigation strategies are derived. Then, an analysis of the dynamical behavior of the interacting robots in unbounded spatial domains is made. The article concludes with the results of computer simulations studies of two or more interacting robots.

Highly Efficient Transmitter for High Peak to Average Power Ratio (PAPR) Waveforms

DTIC Science & Technology

2011-01-19

on the modulated signal topology. N00039-10-C-0071 Page 1 ACRONYM DESCRIPTION FREQUENCY Lower Upper MHz MHz ACAS Avionics Identification ...450 GSM Global Mobile Communications 380 921 HAVE QUICK Military Aircraft Radio 225 400 IFF Avionics Identification . Collision Avoidance and...Channel Ground Air Radio System 30 88 TCAS Avionics Identification , Collision Avoidance and Traffic Alert 1030 1090 VIII Air Traffic Control (Civilian

Step 1: Human System Integration Simulation and Flight Test Progress Report

NASA Technical Reports Server (NTRS)

2005-01-01

The Access 5 Human Systems Integration Work Package produced simulation and flight demonstration planning products for use throughout the program. These included: Test Objectives for Command, Control, Communications; Pilot Questionnaire for Command, Control, Communications; Air Traffic Controller Questionnaire for Command, Control, Communications; Test Objectives for Collision Avoidance; Pilot Questionnaire for Collision Avoidance; Plans for Unmanned Aircraft Systems Control Station Simulations Flight Requirements for the Airspace Operations Demonstration

Dynamical study of low Earth orbit debris collision avoidance using ground based laser

NASA Astrophysics Data System (ADS)

Khalifa, N. S.

2015-06-01

The objective of this paper was to investigate the orbital velocity changes due to the effect of ground based laser force. The resulting perturbations of semi-major axis, miss distance and collision probability of two approaching objects are studied. The analytical model is applied for low Earth orbit debris of different eccentricities and area to mass ratio and the numerical test shows that laser of medium power ∼5 kW can perform a small change Δ V ‾ of an average magnitude of 0.2 cm/s which can be accumulated over time to be about 3 cm/day. Moreover, it is confirmed that applying laser Δ V ‾ results in decreasing collision probability and increasing miss distance in order to avoid collision.

Dash Cam videos on YouTube™ offer insights into factors related to moose-vehicle collisions.

PubMed

Rea, Roy V; Johnson, Chris J; Aitken, Daniel A; Child, Kenneth N; Hesse, Gayle

2018-03-26

To gain a better understanding of the dynamics of moose-vehicle collisions, we analyzed 96 videos of moose-vehicle interactions recorded by vehicle dash-mounted cameras (Dash Cams) that had been posted to the video-sharing website YouTube™. Our objective was to determine the effects of road conditions, season and weather, moose behavior, and driver response to actual collisions compared to near misses when the collision was avoided. We identified 11 variables that were consistently observable in each video and that we hypothesized would help to explain a collision or near miss. The most parsimonious logistic regression model contained variables for number of moose, sight time, vehicle slows, and vehicle swerves (AIC c w = 0.529). This model had good predictive accuracy (AUC = 0.860, SE = 0.041). The only statistically significant variable from this model that explained the difference between moose-vehicle collisions and near misses was 'Vehicle slows'. Our results provide no evidence that road surface conditions (dry, wet, ice or snow), roadside habitat type (forested or cleared), the extent to which roadside vegetation was cleared, natural light conditions (overcast, clear, twilight, dark), season (winter, spring and summer, fall), the presence of oncoming traffic, or the direction from which the moose entered the roadway had any influence on whether a motorist collided with a moose. Dash Cam videos posted to YouTube™ provide a unique source of data for road safety planners trying to understand what happens in the moments just before a moose-vehicle collision and how those factors may differ from moose-vehicle encounters that do not result in a collision. Copyright © 2018 Elsevier Ltd. All rights reserved.

Performance Analysis of Different Backoff Algorithms for WBAN-Based Emerging Sensor Networks

PubMed Central

Khan, Pervez; Ullah, Niamat; Ali, Farman; Ullah, Sana; Hong, Youn-Sik; Lee, Ki-Young; Kim, Hoon

2017-01-01

The Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) procedure of IEEE 802.15.6 Medium Access Control (MAC) protocols for the Wireless Body Area Network (WBAN) use an Alternative Binary Exponential Backoff (ABEB) procedure. The backoff algorithm plays an important role to avoid collision in wireless networks. The Binary Exponential Backoff (BEB) algorithm used in different standards does not obtain the optimum performance due to enormous Contention Window (CW) gaps induced from packet collisions. Therefore, The IEEE 802.15.6 CSMA/CA has developed the ABEB procedure to avoid the large CW gaps upon each collision. However, the ABEB algorithm may lead to a high collision rate (as the CW size is incremented on every alternative collision) and poor utilization of the channel due to the gap between the subsequent CW. To minimize the gap between subsequent CW sizes, we adopted the Prioritized Fibonacci Backoff (PFB) procedure. This procedure leads to a smooth and gradual increase in the CW size, after each collision, which eventually decreases the waiting time, and the contending node can access the channel promptly with little delay; while ABEB leads to irregular and fluctuated CW values, which eventually increase collision and waiting time before a re-transmission attempt. We analytically approach this problem by employing a Markov chain to design the PFB scheme for the CSMA/CA procedure of the IEEE 80.15.6 standard. The performance of the PFB algorithm is compared against the ABEB function of WBAN CSMA/CA. The results show that the PFB procedure adopted for IEEE 802.15.6 CSMA/CA outperforms the ABEB procedure. PMID:28257112

Cooperative Collision Avoidance Technology Demonstration Data Analysis Report

NASA Technical Reports Server (NTRS)

2007-01-01

This report details the National Aeronautics and Space Administration (NASA) Access 5 Project Office Cooperative Collision Avoidance (CCA) Technology Demonstration for unmanned aircraft systems (UAS) conducted from 21 to 28 September 2005. The test platform chosen for the demonstration was the Proteus Optionally Piloted Vehicle operated by Scaled Composites, LLC, flown out of the Mojave Airport, Mojave, CA. A single intruder aircraft, a NASA Gulf stream III, was used during the demonstration to execute a series of near-collision encounter scenarios. Both aircraft were equipped with Traffic Alert and Collision Avoidance System-II (TCAS-II) and Automatic Dependent Surveillance Broadcast (ADS-B) systems. The objective of this demonstration was to collect flight data to support validation efforts for the Access 5 CCA Work Package Performance Simulation and Systems Integration Laboratory (SIL). Correlation of the flight data with results obtained from the performance simulation serves as the basis for the simulation validation. A similar effort uses the flight data to validate the SIL architecture that contains the same sensor hardware that was used during the flight demonstration.

Using Distance Sensors to Perform Collision Avoidance Maneuvres on Uav Applications

NASA Astrophysics Data System (ADS)

Raimundo, A.; Peres, D.; Santos, N.; Sebastião, P.; Souto, N.

2017-08-01

The Unmanned Aerial Vehicles (UAV) and its applications are growing for both civilian and military purposes. The operability of an UAV proved that some tasks and operations can be done easily and at a good cost-efficiency ratio. Nowadays, an UAV can perform autonomous missions. It is very useful to certain UAV applications, such as meteorology, vigilance systems, agriculture, environment mapping and search and rescue operations. One of the biggest problems that an UAV faces is the possibility of collision with other objects in the flight area. To avoid this, an algorithm was developed and implemented in order to prevent UAV collision with other objects. "Sense and Avoid" algorithm was developed as a system for UAVs to avoid objects in collision course. This algorithm uses a Light Detection and Ranging (LiDAR), to detect objects facing the UAV in mid-flights. This light sensor is connected to an on-board hardware, Pixhawk's flight controller, which interfaces its communications with another hardware: Raspberry Pi. Communications between Ground Control Station and UAV are made via Wi-Fi or cellular third or fourth generation (3G/4G). Some tests were made in order to evaluate the "Sense and Avoid" algorithm's overall performance. These tests were done in two different environments: A 3D simulated environment and a real outdoor environment. Both modes worked successfully on a simulated 3D environment, and "Brake" mode on a real outdoor, proving its concepts.

Collision Avoidance Short Course Part I: Theory

NASA Technical Reports Server (NTRS)

Hejduk, Matthew D.

2017-01-01

Satellite conjunction assessment is perhaps the fastest-growing area in space situational awareness and protection, with military, civil, and commercial satellite owner operators embracing more and more sophisticated processes to avoid the avoidable namely collisions between high-value space assets and orbital debris. NASA and CNES have collaborated to offer an introductory short course on all the major aspects of the conjunction assessment problem. This half-day course will cover satellite conjunction dynamics and theory, JSpOC conjunction data products, major risk assessment parameters and plots, conjunction remediation decision support, and present and future challenges. This briefing represents the NASA portion of the course.

Mars Reconnaissance Orbiter Aerobraking Daily Operations and Collision Avoidance

NASA Technical Reports Server (NTRS)

Long, Stacia M.; You, Tung-Han; Halsell, C. Allen; Bhat, Ramachand S.; Demcak, Stuart W.; Graat, Eric J.; Higa, Earl S.; Highsmith, Dolan E.; Mottinger, Neil A.; Jah, Moriba K.

2007-01-01

The Mars Reconnaissance Orbiter reached Mars on March 10, 2006 and performed a Mars orbit insertion maneuver of 1 km/s to enter into a large elliptical orbit. Three weeks later, aerobraking operations began and lasted about five months. Aerobraking utilized the atmospheric drag to reduce the large elliptical orbit into a smaller, near circular orbit. At the time of MRO aerobraking, there were three other operational spacecraft orbiting Mars and the navigation team had to minimize the possibility of a collision. This paper describes the daily operations of the MRO navigation team during this time as well as the collision avoidance strategy development and implementation.

[Micron]ADS-B Detect and Avoid Flight Tests on Phantom 4 Unmanned Aircraft System

NASA Technical Reports Server (NTRS)

Arteaga, Ricardo; Dandachy, Mike; Truong, Hong; Aruljothi, Arun; Vedantam, Mihir; Epperson, Kraettli; McCartney, Reed

2018-01-01

Researchers at the National Aeronautics and Space Administration Armstrong Flight Research Center in Edwards, California and Vigilant Aerospace Systems collaborated for the flight-test demonstration of an Automatic Dependent Surveillance-Broadcast based collision avoidance technology on a small unmanned aircraft system equipped with the uAvionix Automatic Dependent Surveillance-Broadcast transponder. The purpose of the testing was to demonstrate that National Aeronautics and Space Administration / Vigilant software and algorithms, commercialized as the FlightHorizon UAS"TM", are compatible with uAvionix hardware systems and the DJI Phantom 4 small unmanned aircraft system. The testing and demonstrations were necessary for both parties to further develop and certify the technology in three key areas: flights beyond visual line of sight, collision avoidance, and autonomous operations. The National Aeronautics and Space Administration and Vigilant Aerospace Systems have developed and successfully flight-tested an Automatic Dependent Surveillance-Broadcast Detect and Avoid system on the Phantom 4 small unmanned aircraft system. The Automatic Dependent Surveillance-Broadcast Detect and Avoid system architecture is especially suited for small unmanned aircraft systems because it integrates: 1) miniaturized Automatic Dependent Surveillance-Broadcast hardware; 2) radio data-link communications; 3) software algorithms for real-time Automatic Dependent Surveillance-Broadcast data integration, conflict detection, and alerting; and 4) a synthetic vision display using a fully-integrated National Aeronautics and Space Administration geobrowser for three dimensional graphical representations for ownship and air traffic situational awareness. The flight-test objectives were to evaluate the performance of Automatic Dependent Surveillance-Broadcast Detect and Avoid collision avoidance technology as installed on two small unmanned aircraft systems. In December 2016, four flight tests were conducted at Edwards Air Force Base. Researchers in the ground control station looking at displays were able to verify the Automatic Dependent Surveillance-Broadcast target detection and collision avoidance resolutions.

Flexible Virtual Structure Consideration in Dynamic Modeling of Mobile Robots Formation

NASA Astrophysics Data System (ADS)

El Kamel, A. Essghaier; Beji, L.; Lerbet, J.; Abichou, A.

2009-03-01

In cooperative mobile robotics, we look for formation keeping and maintenance of a geometric configuration during movement. As a solution to these problems, the concept of a virtual structure is considered. Based on this idea, we have developed an efficient flexible virtual structure, describing the dynamic model of n vehicles in formation and where the whole formation is kept dependant. Notes that, for 2D and 3D space navigation, only a rigid virtual structure was proposed in the literature. Further, the problem was limited to a kinematic behavior of the structure. Hence, the flexible virtual structure in dynamic modeling of mobile robots formation presented in this paper, gives more capabilities to the formation to avoid obstacles in hostile environment while keeping formation and avoiding inter-agent collision.

Visual feedback training improves postural adjustments associated with moving obstacle avoidance in elderly women.

PubMed

Hatzitaki, V; Voudouris, D; Nikodelis, T; Amiridis, I G

2009-02-01

The study examined the impact of visually guided weight shifting (WS) practice on the postural adjustments evoked by elderly women when avoiding collision with a moving obstacle while standing. Fifty-six healthy elderly women (70.9+/-5.7 years, 87.5+/-9.6 kg) were randomly assigned into one of three groups: a group that completed 12 sessions (25 min, 3s/week) of WS practice in the Anterior/Posterior direction (A/P group, n=20), a group that performed the same practice in the medio/lateral direction (M/L group, n=20) and a control group (n=16). Pre- and post-training, participants were tested in a moving obstacle avoidance task. As a result of practice, postural response onset shifted closer to the time of collision with the obstacle. Side-to-side WS resulted in a reduction of the M/L sway amplitude and an increase of the trunk's velocity during avoidance. It is concluded that visually guided WS practice enhances elderly's ability for on-line visuo-motor processing when avoiding collision eliminating reliance on anticipatory scaling. Specifying the direction of WS seems to be critical for optimizing the transfer of training adaptations.

Small UAV Automatic Ground Collision Avoidance System Design Considerations and Flight Test Results

NASA Technical Reports Server (NTRS)

Sorokowski, Paul; Skoog, Mark; Burrows, Scott; Thomas, SaraKatie

2015-01-01

The National Aeronautics and Space Administration (NASA) Armstrong Flight Research Center Small Unmanned Aerial Vehicle (SUAV) Automatic Ground Collision Avoidance System (Auto GCAS) project demonstrated several important collision avoidance technologies. First, the SUAV Auto GCAS design included capabilities to take advantage of terrain avoidance maneuvers flying turns to either side as well as straight over terrain. Second, the design also included innovative digital elevation model (DEM) scanning methods. The combination of multi-trajectory options and new scanning methods demonstrated the ability to reduce the nuisance potential of the SUAV while maintaining robust terrain avoidance. Third, the Auto GCAS algorithms were hosted on the processor inside a smartphone, providing a lightweight hardware configuration for use in either the ground control station or on board the test aircraft. Finally, compression of DEM data for the entire Earth and successful hosting of that data on the smartphone was demonstrated. The SUAV Auto GCAS project demonstrated that together these methods and technologies have the potential to dramatically reduce the number of controlled flight into terrain mishaps across a wide range of aviation platforms with similar capabilities including UAVs, general aviation aircraft, helicopters, and model aircraft.

77 FR 6000 - Airworthiness Directives; Aviation Communication & Surveillance Systems (ACSS) Traffic Alert and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-07

... Airworthiness Directives; Aviation Communication & Surveillance Systems (ACSS) Traffic Alert and Collision... Communication & Surveillance Systems (ACSS) traffic alert and collision avoidance system (TCAS) units with part...

Particle Filtering for Obstacle Tracking in UAS Sense and Avoid Applications

PubMed Central

Moccia, Antonio

2014-01-01

Obstacle detection and tracking is a key function for UAS sense and avoid applications. In fact, obstacles in the flight path must be detected and tracked in an accurate and timely manner in order to execute a collision avoidance maneuver in case of collision threat. The most important parameter for the assessment of a collision risk is the Distance at Closest Point of Approach, that is, the predicted minimum distance between own aircraft and intruder for assigned current position and speed. Since assessed methodologies can cause some loss of accuracy due to nonlinearities, advanced filtering methodologies, such as particle filters, can provide more accurate estimates of the target state in case of nonlinear problems, thus improving system performance in terms of collision risk estimation. The paper focuses on algorithm development and performance evaluation for an obstacle tracking system based on a particle filter. The particle filter algorithm was tested in off-line simulations based on data gathered during flight tests. In particular, radar-based tracking was considered in order to evaluate the impact of particle filtering in a single sensor framework. The analysis shows some accuracy improvements in the estimation of Distance at Closest Point of Approach, thus reducing the delay in collision detection. PMID:25105154

A switching formation strategy for obstacle avoidance of a multi-robot system based on robot priority model.

PubMed

Dai, Yanyan; Kim, YoonGu; Wee, SungGil; Lee, DongHa; Lee, SukGyu

2015-05-01

This paper describes a switching formation strategy for multi-robots with velocity constraints to avoid and cross obstacles. In the strategy, a leader robot plans a safe path using the geometric obstacle avoidance control method (GOACM). By calculating new desired distances and bearing angles with the leader robot, the follower robots switch into a safe formation. With considering collision avoidance, a novel robot priority model, based on the desired distance and bearing angle between the leader and follower robots, is designed during the obstacle avoidance process. The adaptive tracking control algorithm guarantees that the trajectory and velocity tracking errors converge to zero. To demonstrate the validity of the proposed methods, simulation and experiment results present that multi-robots effectively form and switch formation avoiding obstacles without collisions. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

How do walkers avoid a mobile robot crossing their way?

PubMed

Vassallo, Christian; Olivier, Anne-Hélène; Souères, Philippe; Crétual, Armel; Stasse, Olivier; Pettré, Julien

2017-01-01

Robots and Humans have to share the same environment more and more often. In the aim of steering robots in a safe and convenient manner among humans it is required to understand how humans interact with them. This work focuses on collision avoidance between a human and a robot during locomotion. Having in mind previous results on human obstacle avoidance, as well as the description of the main principles which guide collision avoidance strategies, we observe how humans adapt a goal-directed locomotion task when they have to interfere with a mobile robot. Our results show differences in the strategy set by humans to avoid a robot in comparison with avoiding another human. Humans prefer to give the way to the robot even when they are likely to pass first at the beginning of the interaction. Copyright © 2016 Elsevier B.V. All rights reserved.

Initial Design and Experimental Implementation of the Traffic Advisory Service of ATARS

DTIC Science & Technology

1980-11-03

Traffic 6. Performing Organization Code Advisory Service of ATARS 7. Author(s) 8. Performing Organization Report No Jeffrey L. Gertz ATC-101 9...and Resolution Service ( ATARS ) is a ground-based collision avoidance system which utilizes surveillance data from the Discrete Address Beacon System...to aircraft via the DABS data link. ATARS provides both a traffic advisory and a resolution (collision avoidance) service to aircraft equipped with a

Virtual Acoustics, Aeronautics and Communications

NASA Technical Reports Server (NTRS)

Begault, Durand R.; Null, Cynthia H. (Technical Monitor)

1996-01-01

An optimal approach to auditory display design for commercial aircraft would utilize both spatialized ("3-D") audio techniques and active noise cancellation for safer operations. Results from several aircraft simulator studies conducted at NASA Ames Research Center are reviewed, including Traffic alert and Collision Avoidance System (TCAS) warnings, spoken orientation "beacons" for gate identification and collision avoidance on the ground, and hardware for improved speech intelligibility. The implications of hearing loss amongst pilots is also considered.

Virtual acoustics, aeronautics, and communications

NASA Technical Reports Server (NTRS)

Begault, D. R.; Wenzel, E. M. (Principal Investigator)

1998-01-01

An optimal approach to auditory display design for commercial aircraft would utilize both spatialized (3-D) audio techniques and active noise cancellation for safer operations. Results from several aircraft simulator studies conducted at NASA Ames Research Center are reviewed, including Traffic alert and Collision Avoidance System (TCAS) warnings, spoken orientation "beacons" for gate identification and collision avoidance on the ground, and hardware for improved speech intelligibility. The implications of hearing loss among pilots is also considered.

Opportunities for collision countermeasures using intelligent technologies.

DOT National Transportation Integrated Search

1997-01-01

Since 1991, the National Highway Traffic Safety Administration (NHTSA) has had a concentrated program to facilitate the development and deployment of effective safety-related collision avoidance systems as part of the Intelligent Transportation Syste...

Collision management utilizing CCD and remote sensing technology

NASA Technical Reports Server (NTRS)

Mcdaniel, Harvey E., Jr.

1995-01-01

With the threat of damage to aerospace systems (space station, shuttle, hypersonic a/c, solar power satellites, loss of life, etc.) from collision with debris (manmade/artificial), there exists an opportunity for the design of a novel system (collision avoidance) to be incorporated into the overall design. While incorporating techniques from ccd and remote sensing technologies, an integrated system utilized in the infrared/visible spectrum for detection, tracking, localization, and maneuvering from doppler shift measurements is achievable. Other analysis such as impact assessment, station keeping, chemical, and optical tracking/fire control solutions are possible through this system. Utilizing modified field programmable gated arrays (software reconfiguring the hardware) the mission and mission effectiveness can be varied. This paper outlines the theoretical operation of a prototype system as it applies to collision avoidance (to be followed up by research).

LightForce Photon-Pressure Collision Avoidance: Updated Efficiency Analysis Utilizing a Highly Parallel Simulation Approach

NASA Technical Reports Server (NTRS)

Stupl, Jan; Faber, Nicolas; Foster, Cyrus; Yang, Fan Yang; Nelson, Bron; Aziz, Jonathan; Nuttall, Andrew; Henze, Chris; Levit, Creon

2014-01-01

This paper provides an updated efficiency analysis of the LightForce space debris collision avoidance scheme. LightForce aims to prevent collisions on warning by utilizing photon pressure from ground based, commercial off the shelf lasers. Past research has shown that a few ground-based systems consisting of 10 kilowatt class lasers directed by 1.5 meter telescopes with adaptive optics could lower the expected number of collisions in Low Earth Orbit (LEO) by an order of magnitude. Our simulation approach utilizes the entire Two Line Element (TLE) catalogue in LEO for a given day as initial input. Least-squares fitting of a TLE time series is used for an improved orbit estimate. We then calculate the probability of collision for all LEO objects in the catalogue for a time step of the simulation. The conjunctions that exceed a threshold probability of collision are then engaged by a simulated network of laser ground stations. After those engagements, the perturbed orbits are used to re-assess the probability of collision and evaluate the efficiency of the system. This paper describes new simulations with three updated aspects: 1) By utilizing a highly parallel simulation approach employing hundreds of processors, we have extended our analysis to a much broader dataset. The simulation time is extended to one year. 2) We analyze not only the efficiency of LightForce on conjunctions that naturally occur, but also take into account conjunctions caused by orbit perturbations due to LightForce engagements. 3) We use a new simulation approach that is regularly updating the LightForce engagement strategy, as it would be during actual operations. In this paper we present our simulation approach to parallelize the efficiency analysis, its computational performance and the resulting expected efficiency of the LightForce collision avoidance system. Results indicate that utilizing a network of four LightForce stations with 20 kilowatt lasers, 85% of all conjunctions with a probability of collision Pc > 10 (sup -6) can be mitigated.

Algorithms for Collision Detection Between a Point and a Moving Polygon, with Applications to Aircraft Weather Avoidance

NASA Technical Reports Server (NTRS)

Narkawicz, Anthony; Hagen, George

2016-01-01

This paper proposes mathematical definitions of functions that can be used to detect future collisions between a point and a moving polygon. The intended application is weather avoidance, where the given point represents an aircraft and bounding polygons are chosen to model regions with bad weather. Other applications could possibly include avoiding other moving obstacles. The motivation for the functions presented here is safety, and therefore they have been proved to be mathematically correct. The functions are being developed for inclusion in NASA's Stratway software tool, which allows low-fidelity air traffic management concepts to be easily prototyped and quickly tested.

Collision Avoidance "Short Course" Part III: CA Role in Changing Space Flight Environment

NASA Technical Reports Server (NTRS)

Newman, Lauri

2017-01-01

Satellite conjunction assessment is perhaps the fastest-growing area in space situational awareness and protection, with military, civil, and commercial satellite owner operators embracing more and more sophisticated processes to avoid the avoidable namely collisions between high-value space assets and orbital debris. NASA and CNES have collaborated to offer an introductory short course on all the major aspects of the conjunction assessment problem. This half-day course will cover satellite conjunction dynamics and theory, JSpOC conjunction data products, major risk assessment parameters and plots, conjunction remediation decision support, and present and future challenges. This briefing represents the NASA portion of the course.

Collision avoidance in persons with homonymous visual field defects under virtual reality conditions.

PubMed

Papageorgiou, Eleni; Hardiess, Gregor; Ackermann, Hermann; Wiethoelter, Horst; Dietz, Klaus; Mallot, Hanspeter A; Schiefer, Ulrich

2012-01-01

The aim of the present study was to examine the effect of homonymous visual field defects (HVFDs) on collision avoidance of dynamic obstacles at an intersection under virtual reality (VR) conditions. Overall performance was quantitatively assessed as the number of collisions at a virtual intersection at two difficulty levels. HVFDs were assessed by binocular semi-automated kinetic perimetry within the 90° visual field, stimulus III4e and the area of sparing within the affected hemifield (A-SPAR in deg(2)) was calculated. The effect of A-SPAR, age, gender, side of brain lesion, time since brain lesion and presence of macular sparing on the number of collisions, as well as performance over time were investigated. Thirty patients (10 female, 20 male, age range: 19-71 years) with HVFDs due to unilateral vascular brain lesions and 30 group-age-matched subjects with normal visual fields were examined. The mean number of collisions was higher for patients and in the more difficult level they experienced more collisions with vehicles approaching from the blind side than the seeing side. Lower A-SPAR and increasing age were associated with decreasing performance. However, in agreement with previous studies, wide variability in performance among patients with identical visual field defects was observed and performance of some patients was similar to that of normal subjects. Both patients and healthy subjects displayed equal improvement of performance over time in the more difficult level. In conclusion, our results suggest that visual-field related parameters per se are inadequate in predicting successful collision avoidance. Individualized approaches which also consider compensatory strategies by means of eye and head movements should be introduced. Copyright © 2011 Elsevier Ltd. All rights reserved.

Surface target-tracking guidance by self-organizing formation flight of fixed-wing UAV

NASA Astrophysics Data System (ADS)

Regina, N.; Zanzi, M.

This paper presents a new concept of ground target surveillance based on a formation flight of two Unmanned Aerial Vehicles (UAVs) of fixed-wing type. Each UAV considered in this work has its own guidance law specifically designed for two different aims. A self organizing non-symmetric collaborative surveying scheme has been developed based on pursuers with different roles: the close-up-pursuer and the distance-pursuer. The close-up-pursuer behaves according to a guidance law which takes it to continually over-fly the target, also optimizing flight endurance. On the other hand, the distancepursuer behaves so as to circle around the target by flying at a certain distance and altitude from it; moreover, its motion ensures the maximum “ seeability” of the ground based target. In addition, the guidance law designed for the distance-pursuer also implements a collision avoidance feature in order to prevent possible risks of collision with the close-up-pursuer during the tracking maneuvers. The surveying scheme is non-symmetric in the sense that the collision avoidance feature is accomplished by a guidance law implemented only on one of the two pursuers; moreover, it is collaborative because the surveying is performed by different tasks of two UAVs and is self-organizing because, due to the collision avoidance feature, target tracking does not require pre-planned collision-risk-free trajectories but trajectories are generated in real time.

Experimental characterization of collision avoidance in pedestrian dynamics

NASA Astrophysics Data System (ADS)

Parisi, Daniel R.; Negri, Pablo A.; Bruno, Luciana

2016-08-01

In the present paper, the avoidance behavior of pedestrians was characterized by controlled experiments. Several conflict situations were studied considering different flow rates and group sizes in crossing and head-on configurations. Pedestrians were recorded from above, and individual two-dimensional trajectories of their displacement were recovered after image processing. Lateral swaying amplitude and step lengths were measured for free pedestrians, obtaining similar values to the ones reported in the literature. Minimum avoidance distances were computed in two-pedestrian experiments. In the case of one pedestrian dodging an arrested one, the avoidance distance did not depend on the relative orientation of the still pedestrian with respect to the direction of motion of the first. When both pedestrians were moving, the avoidance distance in a perpendicular encounter was longer than the one obtained during a head-on approach. It was found that the mean curvature of the trajectories was linearly anticorrelated with the mean speed. Furthermore, two common avoidance maneuvers, stopping and steering, were defined from the analysis of the acceleration and curvature in single trajectories. Interestingly, it was more probable to observe steering events than stopping ones, also the probability of simultaneous steering and stopping occurrences was negligible. The results obtained in this paper can be used to validate and calibrate pedestrian dynamics models.

Passenger rail equipment research in the U.S.

DOT National Transportation Integrated Search

2002-03-22

In 1989 the Federal Railroad Administration (FRA) initiated a program of research into the safety aspects of high-speed passenger train systems. Collision safety the balancing of collision avoidance measures of the system with the crashworthiness...

Communications and radar-supported transportation operations and planning : final report.

DOT National Transportation Integrated Search

2017-03-01

This project designs a conceptual framework to harness and mature wireless technology to improve : transportation safety, with a focus on frontal collision warning/collision avoidance (CW/CA) systems. The : framework identifies components of the tech...

Design of an Active Bumper with a Series Elastic Actuator for Pedestrian Protection of Small Unmanned Vehicles

NASA Astrophysics Data System (ADS)

Terumasa, Narukawa; Tomoki, Tsuge; Hiroshi, Yamamoto; Takahiro, Suzuki

2016-09-01

When autonomous unmanned vehicles are operated on sidewalks, the vehicles must have high safety standards such as avoiding injury when they come in contact with pedestrians. In this study, we established a design for preventing serious injury when such collisions occur. We designed an active bumper with a series elastic actuator, with the goal of avoiding serious injury to a pedestrian in a collision with a small unmanned vehicle. The series elastic actuator comprised an elastic element in series with a table driven by a ball screw and servo motor. The active bumper was used to control the contact force between a vehicle and a pedestrian. The optimal force for minimizing the deflection of the object of the collision was derived, and the actuator controlled to apply this optimal force. Numerical simulations showed that the active bumper was successful in improving the collision safety of small unmanned vehicles.

UAV-borne X-band radar for MAV collision avoidance

NASA Astrophysics Data System (ADS)

Moses, Allistair A.; Rutherford, Matthew J.; Kontitsis, Michail; Valavanis, Kimon P.

2011-05-01

Increased use of Miniature (Unmanned) Aerial Vehicles (MAVs) is coincidentally accompanied by a notable lack of sensors suitable for enabling further increases in levels of autonomy and consequently, integration into the National Airspace System (NAS). The majority of available sensors suitable for MAV integration are based on infrared detectors, focal plane arrays, optical and ultrasonic rangefinders, etc. These sensors are generally not able to detect or identify other MAV-sized targets and, when detection is possible, considerable computational power is typically required for successful identification. Furthermore, performance of visual-range optical sensor systems can suffer greatly when operating in the conditions that are typically encountered during search and rescue, surveillance, combat, and most common MAV applications. However, the addition of a miniature radar system can, in consort with other sensors, provide comprehensive target detection and identification capabilities for MAVs. This trend is observed in manned aviation where radar systems are the primary detection and identification sensor system. Within this document a miniature, lightweight X-Band radar system for use on a miniature (710mm rotor diameter) rotorcraft is described. We present analyses of the performance of the system in a realistic scenario with two MAVs. Additionally, an analysis of MAV navigation and collision avoidance behaviors is performed to determine the effect of integrating radar systems into MAV-class vehicles.

Sampling-Based Motion Planning Algorithms for Replanning and Spatial Load Balancing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boardman, Beth Leigh

The common theme of this dissertation is sampling-based motion planning with the two key contributions being in the area of replanning and spatial load balancing for robotic systems. Here, we begin by recalling two sampling-based motion planners: the asymptotically optimal rapidly-exploring random tree (RRT*), and the asymptotically optimal probabilistic roadmap (PRM*). We also provide a brief background on collision cones and the Distributed Reactive Collision Avoidance (DRCA) algorithm. The next four chapters detail novel contributions for motion replanning in environments with unexpected static obstacles, for multi-agent collision avoidance, and spatial load balancing. First, we show improved performance of the RRT*more » when using the proposed Grandparent-Connection (GP) or Focused-Refinement (FR) algorithms. Next, the Goal Tree algorithm for replanning with unexpected static obstacles is detailed and proven to be asymptotically optimal. A multi-agent collision avoidance problem in obstacle environments is approached via the RRT*, leading to the novel Sampling-Based Collision Avoidance (SBCA) algorithm. The SBCA algorithm is proven to guarantee collision free trajectories for all of the agents, even when subject to uncertainties in the knowledge of the other agents’ positions and velocities. Given that a solution exists, we prove that livelocks and deadlock will lead to the cost to the goal being decreased. We introduce a new deconfliction maneuver that decreases the cost-to-come at each step. This new maneuver removes the possibility of livelocks and allows a result to be formed that proves convergence to the goal configurations. Finally, we present a limited range Graph-based Spatial Load Balancing (GSLB) algorithm which fairly divides a non-convex space among multiple agents that are subject to differential constraints and have a limited travel distance. The GSLB is proven to converge to a solution when maximizing the area covered by the agents. The analysis for each of the above mentioned algorithms is confirmed in simulations.« less

Automated Spacecraft Conjunction Assessment at Mars and the Moon

NASA Technical Reports Server (NTRS)

Berry, David; Guinn, Joseph; Tarzi, Zahi; Demcak, Stuart

2012-01-01

Conjunction assessment and collision avoidance are areas of current high interest in space operations. Most current conjunction assessment activity focuses on the Earth orbital environment. Several of the world's space agencies have satellites in orbit at Mars and the Moon, and avoiding collisions there is important too. Smaller number of assets than Earth, and smaller number of organizations involved, but consequences similar to Earth scenarios.This presentation will examine conjunction assessment processes implemented at JPL for spacecraft in orbit at Mars and the Moon.

Development of an in-vehicle intersection collision countermeasure

NASA Astrophysics Data System (ADS)

Pierowicz, John A.

1997-02-01

Intersection collisions constitute approximately twenty-six percent of all accidents in the United States. Because of their complexity, and demands on the perceptual and decision making abilities of the driver, intersections present an increased risk of collisions between automobiles. This situation provides an opportunity to apply advanced sensor and processing capabilities to prevent these collisions. A program to determine the characteristics of intersection collisions and identify potential countermeasures will be described. This program, sponsored by the National Highway Traffic Safety Administration, utilized accident data to develop a taxonomy of intersection crashes. This taxonomy was used to develop a concept for an intersection collision avoidance countermeasure. The concept utilizes in-vehicle position, dynamic status, and millimeter wave radar system and an in-vehicle computer system to provide inputs to an intersection collision avoidance algorithm. Detection of potential violation of traffic control device, or proceeding into the intersection with inadequate gap will lead to the presentation of a warning to the driver. These warnings are presented to the driver primarily via a head-up display and haptic feedback. Roadside to vehicle communication provides information regarding phased traffic signal information. Active control of the vehicle's brake and steering systems are described. Progress in the development of the systems will be presented along with the schedule of future activities.

Active Beacon Collision Avoidance System (BCAS) Conference Proceedings, January 27-28, 1981.

DTIC Science & Technology

1981-01-01

WITH THE SINGLE OBJECTIVE OF PREVENTING MIDAIR COLLISIONS WHEN, FOR WHATEVER REASON, THE PRIMARY SYSTEM FAILS TO PROVIDE ADEQUATE SEPARA- TION. THE... PREVENTION OF MIDAIR-- AND NEAR MIDAIR--COLLISIONS. THAT MUCH IS SIMPLE. BUT JUST LIKE A CONTRACT, IT BEGINS TO GET MORE COMPLiCATED WHEN WE START ADDING THE...34WHEREAS" AND THE DETAILS. FIRST, ACTIVE BCAS IS DESIGNED TO PERFORM THE COLLISION- PREVENTION FUNCTION IN AN ENVIRONMENT WHERE OTHER AIRCRAFT FROM

Comparative Analysis of ACAS-Xu and DAIDALUS Detect-and-Avoid Systems

NASA Technical Reports Server (NTRS)

Davies, Jason T.; Wu, Minghong G.

2018-01-01

The Detect and Avoid (DAA) capability of a recent version (Run 3) of the Airborne Collision Avoidance System-Xu (ACAS-Xu) is measured against that of the Detect and AvoID Alerting Logic for Unmanned Systems (DAIDALUS), a reference algorithm for the Phase 1 Minimum Operational Performance Standards (MOPS) for DAA. This comparative analysis of the two systems' alerting and horizontal guidance outcomes is conducted through the lens of the Detect and Avoid mission using flight data of scripted encounters from a recent flight test. Results indicate comparable timelines and outcomes between ACAS-Xu's Remain Well Clear alert and guidance and DAIDALUS's corrective alert and guidance, although ACAS-Xu's guidance appears to be more conservative. ACAS-Xu's Collision Avoidance alert and guidance occurs later than DAIDALUS's warning alert and guidance, and overlaps with DAIDALUS's timeline of maneuver to remain Well Clear. Interesting discrepancies between ACAS-Xu's directive guidance and DAIDALUS's "Regain Well Clear" guidance occur in some scenarios.

CAESAR: An Initiative of Public Service for Collision Risks Mitigation

NASA Astrophysics Data System (ADS)

Laporte, Francois; Moury, Monique; Beaumet, Gregory

2013-09-01

This paper starts by describing the conjunction analysis which has to be performed using CSM data provided by JSpOC. This description not only demonstrates that Collision Avoidance is a 2-step process (close approach detection followed by risk evaluation for collision avoidance decision) but also leads to the conclusion that there is a need for Middle Man role.After describing the Middle Man concept, it introduces the French response CAESAR and the need for collaborative work environment which is implied by Middle Man concept. It includes a description of the environment put in place for CAESAR (secure website and dedicated tools), the content of the service, and the condition for the distribution of the CNES software JAC and the advantages for subscribers.

Pilot Non-Conformance to Alerting System Commands

NASA Technical Reports Server (NTRS)

Pritchett, Amy R.; Hansman, R. John

1997-01-01

Instances of pilot non-conformance to alerting system commands have been identified in previous studies. Pilot non-conformance changes the final behavior of the system, and therefore may reduce actual performance from that anticipated. A simulator study has examined pilot non-conformance, using the task of collision avoidance during closely spaced parallel approaches as a case study. Consonance between the display and the alerting system was found to significantly improve subject agreement with automatic alerts. Based on these results, a more general discussion of the factors involved in pilot conformance is given, and design guidelines for alerting systems are given.

Collision Avoidance Short Course: Conjunction Assessment Risk Analysis - NASA Robotic CARA. Part I: ; Theory

NASA Technical Reports Server (NTRS)

Hejduk, M. D.; Frigm, Ryan C.

2015-01-01

Satellite conjunction assessment is perhaps the fastest growing area in space situational awareness and protection with military, civil and commercial satellite owner-operators embracing more and more sophisticated processes to avoid the avoidable - namely collisions between high value space assets and orbital debris. NASA and Centre National d'Etudes Spatiales (CNES) have collaborated to offer an introductory short course on all the major aspects of the conjunctions assessment problem. This half-day course will cover satellite conjunction dynamics and theory. Joint Space Operations Center (JsPOC) conjunction data products, major risk assessment parameters and plots, conjunction remediation decision support, and present and future challenges. This briefing represents the NASA portion of the course.

Changes in Drivers’ Visual Performance during the Collision Avoidance Process as a Function of Different Field of Views at Intersections

PubMed Central

Yan, Xuedong; Zhang, Xinran; Zhang, Yuting; Li, Xiaomeng; Yang, Zhuo

2016-01-01

The intersection field of view (IFOV) indicates an extent that the visual information can be observed by drivers. It has been found that further enhancing IFOV can significantly improve emergent collision avoidance performance at intersections, such as faster brake reaction time, smaller deceleration rate, and lower traffic crash involvement risk. However, it is not known how IFOV affects drivers’ eye movements, visual attention and the relationship between visual searching and traffic safety. In this study, a driving simulation experiment was conducted to uncover the changes in drivers’ visual performance during the collision avoidance process as a function of different field of views at an intersection by using an eye tracking system. The experimental results showed that drivers’ ability in identifying the potential hazard in terms of visual searching was significantly affected by different IFOV conditions. As the IFOVs increased, drivers had longer gaze duration (GD) and more number of gazes (NG) in the intersection surrounding areas and paid more visual attention to capture critical visual information on the emerging conflict vehicle, thus leading to a better collision avoidance performance and a lower crash risk. It was also found that female drivers had a better visual performance and a lower crash rate than male drivers. From the perspective of drivers’ visual performance, the results strengthened the evidence that further increasing intersection sight distance standards should be encouraged for enhancing traffic safety. PMID:27716824

Theory of Aircraft Collision-Avoidance System Design and Evaluation

DOT National Transportation Integrated Search

1971-05-01

The problem of aircraft anti-collision system design and evaluation is discussed in this work. Two evaluation criteria, conflict ratio and probability of missed critical alarm are formulated and are found to be independent of both traffic density and...

LightForce Photon-pressure Collision Avoidance: Efficiency Analysis in the Current Debris Environment and Long-Term Simulation Perspective

NASA Technical Reports Server (NTRS)

Yang, Fan Y.; Nelson, Bron; Carlino, Roberto; Perez, Andres D.; Faber, Nicolas; Henze, Chris; Karacahoglu, Arif G.; O'Toole, Conor; Swenson, Jason; Stupl, Jan

2015-01-01

This work provides an efficiency analysis of the LightForce space debris collision avoidance scheme in the current debris environment and describes a simulation approach to assess its impact on the long-term evolution of the space debris environment. LightForce aims to provide just-in-time collision avoidance by utilizing photon pressure from ground-based industrial lasers. These ground stations impart minimal accelerations to increase the miss distance for a predicted conjunction between two objects. In the first part of this paper we will present research that investigates the short-term effect of a few systems consisting of 10kW class lasers directed by 1.5 m diameter telescopes using adaptive optics. The results found such a network of ground stations to mitigate more than 85 percent of conjunctions and could lower the expected number of collisions in Low Earth Orbit (LEO) by an order of magnitude. While these are impressive numbers that indicate LightForce's utility in the short-term, the remaining 15 percent of possible collisions contain (among others) conjunctions between two massive objects that would add large amount of debris if they collide. Still, conjunctions between massive objects and smaller objects can be mitigated. Hence we choose to expand the capabilities of the simulation software to investigate the overall effect of a network of LightForce stations on the long-term debris evolution. In the second part of this paper, we will present the planed simulation approach for that effort.

First annual report : automotive collision avoidance system field operational test

DOT National Transportation Integrated Search

2002-05-01

In June of 1999, the National Highway Traffic Safety Administration entered into a cooperative research agreement with General Motors to advance the state-of-the-art of rear-end collision warning technology and conduct a field operational test of a f...

Anticipatory sensors for collision avoidance and crash protection as applied to vehicle safety research.

DOT National Transportation Integrated Search

1973-05-01

Considerable effort has been expended in recent years to develop anticipatory crash sensors-effective means of detecting motor vehicle collisions immediately prior to occurrence. If the potential crash is sensed early enough, evasive action may be in...

Bipartite flocking for multi-agent systems

NASA Astrophysics Data System (ADS)

Fan, Ming-Can; Zhang, Hai-Tao; Wang, Miaomiao

2014-09-01

This paper addresses the bipartite flock control problem where a multi-agent system splits into two clusters upon internal or external excitations. Using structurally balanced signed graph theory, LaSalle's invariance principle and Barbalat's Lemma, we prove that the proposed algorithm guarantees a bipartite flocking behavior. In each of the two disjoint clusters, all individuals move with the same direction. Meanwhile, every pair of agents in different clusters moves with opposite directions. Moreover, all agents in the two separated clusters approach a common velocity magnitude, and collision avoidance among all agents is ensured as well. Finally, the proposed bipartite flock control method is examined by numerical simulations. The bipartite flocking motion addressed by this paper has its references in both natural collective motions and human group behaviors such as predator-prey and panic escaping scenarios.

Sensor Fusion Based Model for Collision Free Mobile Robot Navigation

PubMed Central

Almasri, Marwah; Elleithy, Khaled; Alajlan, Abrar

2015-01-01

Autonomous mobile robots have become a very popular and interesting topic in the last decade. Each of them are equipped with various types of sensors such as GPS, camera, infrared and ultrasonic sensors. These sensors are used to observe the surrounding environment. However, these sensors sometimes fail and have inaccurate readings. Therefore, the integration of sensor fusion will help to solve this dilemma and enhance the overall performance. This paper presents a collision free mobile robot navigation based on the fuzzy logic fusion model. Eight distance sensors and a range finder camera are used for the collision avoidance approach where three ground sensors are used for the line or path following approach. The fuzzy system is composed of nine inputs which are the eight distance sensors and the camera, two outputs which are the left and right velocities of the mobile robot’s wheels, and 24 fuzzy rules for the robot’s movement. Webots Pro simulator is used for modeling the environment and the robot. The proposed methodology, which includes the collision avoidance based on fuzzy logic fusion model and line following robot, has been implemented and tested through simulation and real time experiments. Various scenarios have been presented with static and dynamic obstacles using one robot and two robots while avoiding obstacles in different shapes and sizes. PMID:26712766

Sensor Fusion Based Model for Collision Free Mobile Robot Navigation.

PubMed

Almasri, Marwah; Elleithy, Khaled; Alajlan, Abrar

2015-12-26

Autonomous mobile robots have become a very popular and interesting topic in the last decade. Each of them are equipped with various types of sensors such as GPS, camera, infrared and ultrasonic sensors. These sensors are used to observe the surrounding environment. However, these sensors sometimes fail and have inaccurate readings. Therefore, the integration of sensor fusion will help to solve this dilemma and enhance the overall performance. This paper presents a collision free mobile robot navigation based on the fuzzy logic fusion model. Eight distance sensors and a range finder camera are used for the collision avoidance approach where three ground sensors are used for the line or path following approach. The fuzzy system is composed of nine inputs which are the eight distance sensors and the camera, two outputs which are the left and right velocities of the mobile robot's wheels, and 24 fuzzy rules for the robot's movement. Webots Pro simulator is used for modeling the environment and the robot. The proposed methodology, which includes the collision avoidance based on fuzzy logic fusion model and line following robot, has been implemented and tested through simulation and real time experiments. Various scenarios have been presented with static and dynamic obstacles using one robot and two robots while avoiding obstacles in different shapes and sizes.

Automatic Dependent Surveillance Broadcast: [micro]ADS-B Detect-and-Avoid Flight Tests

NASA Technical Reports Server (NTRS)

Arteaga, Ricardo; Dandachy, Mike

2018-01-01

The testing and demonstrations are necessary for both parties to further development and certification of the technology in three key areas; flights beyond line of sight, collision avoidance, and autonomous operations.

Advanced Vehicle Control Systems Potential Tort Liability For Developers

DOT National Transportation Integrated Search

1993-12-01

AUTOMOBILE ACCIDENTS AVOIDED BECAUSE THE AUTOMATIC COLLISION AVOIDANCE SYSTEM APPLIES THE BRAKES, HIGHWAYS WHICH ACCOMMODATE MORE VEHICLES WITH FEWER ACCIDENTS, AND EVEN CARS WHICH ARE PILOTED ENTIRELY BY SOPHISTICATED ELECTRONIC SYSTEMS -- ALL OF TH...

Phase I interim report : automotive collision avoidance system field operational test

DOT National Transportation Integrated Search

2002-05-30

In June of 1999, the National Highway Traffic Safety Administration entered into a cooperative research agreement with General Motors to advance the state-of-the-art of rear-end collision warning technology and conduct a field operational test of a f...

Surprise braking trials, time-to-collision judgments, and "first look" maneuvers under realistic rear-end crash scenarios

DOT National Transportation Integrated Search

2005-08-01

This project continues to build upon the foundation provided by the human factors experimentation conducted in the previous Crash Avoidance Metrics Partnership (CAMP) Forward Collision Warning (FCW) system efforts. As in the previous CAMP FCW researc...

Scattering of trajectories of hazardous asteroids

NASA Astrophysics Data System (ADS)

Sokolov, Leonid; Petrov, Nikita; Kuteeva, Galina; Vasilyev, Andrey

2018-05-01

Early detection of possible collisions of asteroids with the Earth is necessary to exept the asteroid-comet hazard. Many collisions associate with resonant returns after preceding approaches. The difficulty of collisions prediction is associated with a resonant returns after encounters with the Earth due to loss of precision in these predictions. On the other hand, we can use the fly-by effect to avoid hazardous asteroid from collision. The main research object is the asteroid Apophis (99942), for which we found about 100 orbits of possible impacts with the Earth and more than 10 - with the Moon. It is shown that the early (before 2029) change of the Apophis orbit allows to avoid all main impacts with the Earth in 21st century, associated with resonant returns, and such a change of the orbit, in principle, is feasible. The scattering of possible trajectories of Apophis after 2029 and after 2051, as well as 2015 RN35 and other dangerous objects, is discussed.

Speed Approach for UAV Collision Avoidance

NASA Astrophysics Data System (ADS)

Berdonosov, V. D.; Zivotova, A. A.; Htet Naing, Zaw; Zhuravlev, D. O.

2018-05-01

The article represents a new approach of defining potential collision of two or more UAVs in a common aviation area. UAVs trajectories are approximated by two or three trajectories’ points obtained from the ADS-B system. In the process of defining meeting points of trajectories, two cutoff values of the critical speed range, at which a UAVs collision is possible, are calculated. As calculation expressions for meeting points and cutoff values of the critical speed are represented in the analytical form, even if an on-board computer system has limited computational capacity, the time for calculation will be far less than the time of receiving data from ADS-B. For this reason, calculations can be updated at each cycle of new data receiving, and the trajectory approximation can be bounded by straight lines. Such approach allows developing the compact algorithm of collision avoidance, even for a significant amount of UAVs (more than several dozens). To proof the research adequacy, modeling was performed using a software system developed specifically for this purpose.

A trial of retrofitted advisory collision avoidance technology in government fleet vehicles.

PubMed

Thompson, James P; Mackenzie, Jamie R R; Dutschke, Jeffrey K; Baldock, Matthew R J; Raftery, Simon J; Wall, John

2018-06-01

In-vehicle collision avoidance technology (CAT) has the potential to prevent crash involvement. In 2015, Transport for New South Wales undertook a trial of a Mobileye 560 CAT system that was installed in 34 government fleet vehicles for a period of seven months. The system provided headway monitoring, lane departure, forward collision and pedestrian collision warnings, using audio and visual alerts. The purpose of the trial was to determine whether the technology could change the driving behaviour of fleet vehicle drivers and improve their safety. The evaluation consisted of three components: (1) analysis of objective data to examine effects of the technology on driving behaviour, (2) analysis of video footage taken from a sample of the vehicles to examine driving circumstances that trigger headway monitoring and forward collision warnings, and (3) a survey completed by 122 of the 199 individuals who drove the trial vehicles to examine experiences with, and attitudes to, the technology. Analysis of the objective data found that the system resulted in changes in behaviour with increased headway and improved lane keeping, but that these improvements dissipated once the warning alerts were switched off. Therefore, the system is capable of altering behaviour but only when it is actively providing alerts. In-vehicle video footage revealed that over a quarter of forward collision warnings were false alarms, in which a warning event was triggered despite there being no vehicle travelling ahead. The surveyed drivers recognised that the system could improve safety but most did not wish to use it themselves as they found it to be distracting and felt that it would not prevent them from having a crash. The results demonstrate that collision avoidance technology can improve driving behaviour but drivers may need to be educated about the potential benefits for their driving in order to accept the technology. Copyright © 2018 Elsevier Ltd. All rights reserved.

Volvo drivers' experiences with advanced crash avoidance and related technologies.

PubMed

Eichelberger, Angela H; McCartt, Anne T

2014-01-01

Crash avoidance technologies can potentially prevent or mitigate many crashes, but their success depends in part on driver acceptance. Owners of 2010-2012 model Volvo vehicles with several technologies were interviewed about their experiences. Interviews were conducted in summer 2012 with 155 owners of vehicles with City Safety as a standard feature; 145 owners with an optional technology package that included adaptive cruise control, distance alert, collision warning with full auto brake (and pedestrian detection on certain models), driver alert control, and lane departure warning; and 172 owners with both City Safety and the technology package. The survey response rates were 21 percent for owners with City Safety, 30 percent for owners with the technology package, and 27 percent for owners with both. Ten percent of owners opted out before the telephone survey began, and 18 percent declined to participate when called. Despite some annoyance, most respondents always leave the systems on, although fewer do so for lane departure warning (59%). For each of the systems, at least 80 percent of respondents with the system would want it on their next vehicle. Many respondents reported safer driving habits with the systems (e.g., following less closely with adaptive cruise control, using turn signals more often with lane departure warning). Fewer respondents reported potentially unsafe behavior, such as allowing the vehicle to brake for them at least some of the time. About one third of respondents experienced autonomous braking when they believed they were at risk of crashing, and about one fifth of respondents thought it had prevented a crash. About one fifth of respondents with the technology package reported that they were confused or misunderstood which safety system had activated in their vehicle. Consistent with the results for early adopters in the previous survey of Volvo and Infiniti owners, the present survey found that driver acceptance of the technologies remains high, although less so for lane departure warning. This study is the first to report drivers' experiences with City Safety, a collision avoidance system provided as standard equipment on certain Volvo 2010-2012 models, and driver acceptance of this system was high, although not to the same extent as the optional forward collision avoidance system. Future research should continue to monitor drivers' experiences with these technologies as they become available in more vehicles.

14 CFR Appendix B to Part 141 - Private Pilot Certification Course

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Recognition of critical weather situations from the ground and in flight, windshear avoidance, and the... aircraft, including collision avoidance, and recognition and avoidance of wake turbulence; (8) Effects of... takeoffs and 10 landings to a full stop (with each landing involving a flight in the traffic pattern) at an...

14 CFR Appendix B to Part 141 - Private Pilot Certification Course

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Recognition of critical weather situations from the ground and in flight, windshear avoidance, and the... aircraft, including collision avoidance, and recognition and avoidance of wake turbulence; (8) Effects of... takeoffs and 10 landings to a full stop (with each landing involving a flight in the traffic pattern) at an...

Proteus in flight over Southern California

NASA Image and Video Library

2003-03-27

Scaled Composites' unique tandem-wing Proteus was the testbed for a series of UAV collision-avoidance flight demonstrations. An Amphitech 35GHz radar unit installed below Proteus' nose was the primary sensor for the Detect, See and Avoid tests.

Proteus front view in flight

NASA Image and Video Library

2003-03-27

Scaled Composites' unique tandem-wing Proteus was the testbed for a series of UAV collision-avoidance flight demonstrations. An Amphitech 35GHz radar unit installed below Proteus' nose was the primary sensor for the Detect, See and Avoid tests.

UAS in the NAS Flight Test Series 4 Overview

NASA Technical Reports Server (NTRS)

Murphy, Jim

2016-01-01

Flight Test Series 4 (FT4) provides the researchers with an opportunity to expand on the data collected during the first flight tests. Following Flight Test Series 3, additional scripted encounters with different aircraft performance and sensors will be conducted. FT4 is presently planned for Spring of 2016 to ensure collection of data to support the validation of the final RTCA Phase 1 DAA (Detect and Avoid) Minimum Operational Performance Standards (MOPS). There are three research objectives associated with this goal: Evaluate the performance of the DAA system against cooperative and non-cooperative aircraft encounters Evaluate UAS (Unmanned Aircraft Systems) pilot performance in response to DAA maneuver guidance and alerting with live intruder encounters Evaluate TCAS/DAA (Traffic Alert and Collision Avoidance System/Detect and Avoid) interoperability. This flight test series will focus on only the Scripted Encounters configuration, supporting the collection of data to validate the interoperability of DAA and collision avoidance algorithms.

Path planning for assembly of strut-based structures. Thesis

NASA Technical Reports Server (NTRS)

Muenger, Rolf

1991-01-01

A path planning method with collision avoidance for a general single chain nonredundant or redundant robot is proposed. Joint range boundary overruns are also avoided. The result is a sequence of joint vectors which are passed to a trajectory planner. A potential field algorithm in joint space computes incremental joint vectors delta-q = delta-q(sub a) + delta-q(sub c) + delta-q(sub r). Adding delta-q to the robot's current joint vector leads to the next step in the path. Delta-q(sub a) is obtained by computing the minimum norm solution of the underdetermined linear system J delta-q(sub a) = x(sub a) where x(sub a) is a translational and rotational force vector that attracts the robot to its goal position and orientation. J is the manipulator Jacobian. Delta-q(sub c) is a collision avoidance term encompassing collisions between the robot (links and payload) and obstacles in the environment as well as collisions among links and payload of the robot themselves. It is obtained in joint space directly. Delta-q(sub r) is a function of the current joint vector and avoids joint range overruns. A higher level discrete search over candidate safe positions is used to provide alternatives in case the potential field algorithm encounters a local minimum and thus fails to reach the goal. The best first search algorithm A* is used for graph search. Symmetry properties of the payload and equivalent rotations are exploited to further enlarge the number of alternatives passed to the potential field algorithm.

Spacecraft Collision Avoidance

NASA Astrophysics Data System (ADS)

Bussy-Virat, Charles

The rapid increase of the number of objects in orbit around the Earth poses a serious threat to operational spacecraft and astronauts. In order to effectively avoid collisions, mission operators need to assess the risk of collision between the satellite and any other object whose orbit is likely to approach its trajectory. Several algorithms predict the probability of collision but have limitations that impair the accuracy of the prediction. An important limitation is that uncertainties in the atmospheric density are usually not taken into account in the propagation of the covariance matrix from current epoch to closest approach time. The Spacecraft Orbital Characterization Kit (SpOCK) was developed to accurately predict the positions and velocities of spacecraft. The central capability of SpOCK is a high accuracy numerical propagator of spacecraft orbits and computations of ancillary parameters. The numerical integration uses a comprehensive modeling of the dynamics of spacecraft in orbit that includes all the perturbing forces that a spacecraft is subject to in orbit. In particular, the atmospheric density is modeled by thermospheric models to allow for an accurate representation of the atmospheric drag. SpOCK predicts the probability of collision between two orbiting objects taking into account the uncertainties in the atmospheric density. Monte Carlo procedures are used to perturb the initial position and velocity of the primary and secondary spacecraft from their covariance matrices. Developed in C, SpOCK supports parallelism to quickly assess the risk of collision so it can be used operationally in real time. The upper atmosphere of the Earth is strongly driven by the solar activity. In particular, abrupt transitions from slow to fast solar wind cause important disturbances of the atmospheric density, hence of the drag acceleration that spacecraft are subject to. The Probability Distribution Function (PDF) model was developed to predict the solar wind speed five days in advance. In particular, the PDF model is able to predict rapid enhancements in the solar wind speed. It was found that 60% of the positive predictions were correct, while 91% of the negative predictions were correct, and 20% to 33% of the peaks in the speed were found by the model. En-semble forecasts provide the forecasters with an estimation of the uncertainty in the prediction, which can be used to derive uncertainties in the atmospheric density and in the drag acceleration. The dissertation then demonstrates that uncertainties in the atmospheric density result in large uncertainties in the prediction of the probability of collision. As an example, the effects of a geomagnetic storm on the probability of collision are illustrated. The research aims at providing tools and analyses that help understand and predict the effects of uncertainties in the atmospheric density on the probability of collision. The ultimate motivation is to support mission operators in making the correct decision with regard to a potential collision avoidance maneuver by providing an uncertainty on the prediction of the probability of collision instead of a single value. This approach can help avoid performing unnecessary costly maneuvers, while making sure that the risk of collision is fully evaluated.

Unmanned Aircraft Systems Human-in-the-Loop Controller and Pilot Acceptability Study: Collision Avoidance, Self-Separation, and Alerting Times (CASSAT)

NASA Technical Reports Server (NTRS)

Comstock, James R., Jr.; Ghatas, Rania W.; Vincent, Michael J.; Consiglio, Maria C.; Munoz, Cesar; Chamberlain, James P.; Volk, Paul; Arthur, Keith E.

2016-01-01

The Federal Aviation Administration (FAA) has been mandated by the Congressional funding bill of 2012 to open the National Airspace System (NAS) to Unmanned Aircraft Systems (UAS). With the growing use of unmanned systems, NASA has established a multi-center "UAS Integration in the NAS" Project, in collaboration with the FAA and industry, and is guiding its research efforts to look at and examine crucial safety concerns regarding the integration of UAS into the NAS. Key research efforts are addressing requirements for detect-and-avoid (DAA), self-separation (SS), and collision avoidance (CA) technologies. In one of a series of human-in-the-loop experiments, NASA Langley Research Center set up a study known as Collision Avoidance, Self-Separation, and Alerting Times (CASSAT). The first phase assessed active air traffic controller interactions with DAA systems and the second phase examined reactions to the DAA system and displays by UAS Pilots at a simulated ground control station (GCS). Analyses of the test results from Phase I and Phase II are presented in this paper. Results from the CASSAT study and previous human-in-the-loop experiments will play a crucial role in the FAA's establishment of rules, regulations, and procedures to safely, efficiently, and effectively integrate UAS into the NAS.

Probability-based hazard avoidance guidance for planetary landing

NASA Astrophysics Data System (ADS)

Yuan, Xu; Yu, Zhengshi; Cui, Pingyuan; Xu, Rui; Zhu, Shengying; Cao, Menglong; Luan, Enjie

2018-03-01

Future landing and sample return missions on planets and small bodies will seek landing sites with high scientific value, which may be located in hazardous terrains. Autonomous landing in such hazardous terrains and highly uncertain planetary environments is particularly challenging. Onboard hazard avoidance ability is indispensable, and the algorithms must be robust to uncertainties. In this paper, a novel probability-based hazard avoidance guidance method is developed for landing in hazardous terrains on planets or small bodies. By regarding the lander state as probabilistic, the proposed guidance algorithm exploits information on the uncertainty of lander position and calculates the probability of collision with each hazard. The collision probability serves as an accurate safety index, which quantifies the impact of uncertainties on the lander safety. Based on the collision probability evaluation, the state uncertainty of the lander is explicitly taken into account in the derivation of the hazard avoidance guidance law, which contributes to enhancing the robustness to the uncertain dynamics of planetary landing. The proposed probability-based method derives fully analytic expressions and does not require off-line trajectory generation. Therefore, it is appropriate for real-time implementation. The performance of the probability-based guidance law is investigated via a set of simulations, and the effectiveness and robustness under uncertainties are demonstrated.

Speed kills: ineffective avian escape responses to oncoming vehicles

PubMed Central

DeVault, Travis L.; Blackwell, Bradley F.; Seamans, Thomas W.; Lima, Steven L.; Fernández-Juricic, Esteban

2015-01-01

Animal–vehicle collisions cause high levels of vertebrate mortality worldwide, and what goes wrong when animals fail to escape and ultimately collide with vehicles is not well understood. We investigated alert and escape behaviours of captive brown-headed cowbirds (Molothrus ater) in response to virtual vehicle approaches of different sizes and at speeds ranging from 60 to 360 km h−1. Alert and flight initiation distances remained similar across vehicle speeds, and accordingly, alert and flight initiation times decreased at higher vehicle speeds. Thus, avoidance behaviours in cowbirds appeared to be based on distance rather than time available for escape, particularly at 60–150 km h−1; however, at higher speeds (more than or equal to 180 km h−1) no trend in response behaviour was discernible. As vehicle speed increased, cowbirds did not have enough time to assess the approaching vehicle, and cowbirds generally did not initiate flight with enough time to avoid collision when vehicle speed exceeded 120 km h−1. Although potentially effective for evading predators, the decision-making process used by cowbirds in our study appears maladaptive in the context of avoiding fast-moving vehicles. Our methodological approach and findings provide a framework to assess how novel management strategies could affect escape rules, and the sensory and cognitive abilities animals use to avoid vehicle collisions. PMID:25567648

The Monotonic Lagrangian Grid for Fast Air-Traffic Evaluation

NASA Technical Reports Server (NTRS)

Alexandrov, Natalia; Kaplan, Carolyn; Oran, Elaine; Boris, Jay

2010-01-01

This paper describes the continued development of a dynamic air-traffic model, ATMLG, intended for rapid evaluation of rules and methods to control and optimize transport systems. The underlying data structure is based on the Monotonic Lagrangian Grid (MLG), which is used for sorting and ordering positions and other data needed to describe N moving bodies, and their interactions. In ATMLG, the MLG is combined with algorithms for collision avoidance and updating aircraft trajectories. Aircraft that are close to each other in physical space are always near neighbors in the MLG data arrays, resulting in a fast nearest-neighbor interaction algorithm that scales as N. In this paper, we use ATMLG to examine how the ability to maintain a required separation between aircraft decreases as the number of aircraft in the volume increases. This requires keeping track of the primary and subsequent collision avoidance maneuvers necessary to maintain a five mile separation distance between all aircraft. Simulation results show that the number of collision avoidance moves increases exponentially with the number of aircraft in the volume.

CA-LOD: Collision Avoidance Level of Detail for Scalable, Controllable Crowds

NASA Astrophysics Data System (ADS)

Paris, Sébastien; Gerdelan, Anton; O'Sullivan, Carol

The new wave of computer-driven entertainment technology throws audiences and game players into massive virtual worlds where entire cities are rendered in real time. Computer animated characters run through inner-city streets teeming with pedestrians, all fully rendered with 3D graphics, animations, particle effects and linked to 3D sound effects to produce more realistic and immersive computer-hosted entertainment experiences than ever before. Computing all of this detail at once is enormously computationally expensive, and game designers as a rule, have sacrificed the behavioural realism in favour of better graphics. In this paper we propose a new Collision Avoidance Level of Detail (CA-LOD) algorithm that allows games to support huge crowds in real time with the appearance of more intelligent behaviour. We propose two collision avoidance models used for two different CA-LODs: a fuzzy steering focusing on the performances, and a geometric steering to obtain the best realism. Mixing these approaches allows to obtain thousands of autonomous characters in real time, resulting in a scalable but still controllable crowd.

Remote Maneuver of Space Debris Using Photon Pressure for Active Collision Avoidance

NASA Astrophysics Data System (ADS)

Smith, C.

2014-09-01

The Space Environment Research Corporation (SERC) is a consortium of companies and research institutions that have joined together to pursue research and development of technologies and capabilities that will help to preserve the orbital space environment. The consortium includes, Electro Optics Systems (Australia), Lockheed Martin Australia, Optus Satellite Systems (Australia), The Australian national University, RMIT University, National Institute of Information and Communications Technology (NICT, Japan) as well as affiliates from NASA Ames and ESA. SERC is also the recipient of and Australian Government Cooperative Research Centre grant. SERC will pursue a wide ranging research program including technologies to improve tracking capability and capacity, orbit determination and propagation algorithms, conjunction analysis and collision avoidance. All of these technologies will contribute to the flagship program to demonstrate active collision avoidance using photon pressure to provide remote maneuver of space debris. This project joins of the proposed NASA Lightforce concept with infrastructure and capabilities provided by SERC. This paper will describe the proposed research and development program to provide an on-orbit demonstration within the next five years for remote maneuver of space debris.

Medication and Driving-Appropriate Interventions.

PubMed

Hitosugi, Masahito

2017-01-01

Sudden illness while driving has been identified as a major cause of vehicle collisions, accounting for approximately 1 in 10 collisions. Because most drivers who experience sudden illnesses while driving do not perform avoidance maneuvers, the improvement of drivers' health is being promoted as a traffic safety strategy. Although stroke, heart disease, and epilepsy are common causes of sudden illness, common symptoms, such as abdominal cramps, vertigo, and syncope can also cause problems during driving. We found that regular referral to physicians was significantly less common among drivers who experienced health-related vehicle collisions or incidents. Inadequate control of chronic disease might lead to unusual symptoms and the onset of major attacks. Medications are prescribed to patients to relieve their symptoms and/or bring their diseases under control. However, pharmacists and doctors should ensure that patients are treated with appropriate medications to avoid drivers being distracted due to adverse reactions to medications. The author suggests that it is important to keep drivers in good health and administer appropriate medications if necessary. Both pharmacists and doctors should warn drivers that sudden illness or medication-associated distractions can cause vehicle collisions. Such interventions might contribute to reducing the frequency of sudden illness-related vehicle collisions.

Using Collision Cones to Asses Biological Deconiction Methods

NASA Astrophysics Data System (ADS)

Brace, Natalie

For autonomous vehicles to navigate the world as efficiently and effectively as biological species, improvements are needed in terms of control strategies and estimation algorithms. Reactive collision avoidance is one specific area where biological systems outperform engineered algorithms. To better understand the discrepancy between engineered and biological systems, a collision avoidance algorithm was applied to frames of trajectory data from three biological species (Myotis velifer, Hirundo rustica, and Danio aequipinnatus). The algorithm uses information that can be sensed through visual cues (relative position and velocity) to define collision cones which are used to determine if agents are on a collision course and if so, to find a safe velocity that requires minimal deviation from the original velocity for each individual agent. Two- and three-dimensional versions of the algorithm with constant speed and maximum speed velocity requirements were considered. The obstacles provided to the algorithm were determined by the sensing range in terms of either metric or topological distance. The calculated velocities showed good correlation with observed velocities over the range of sensing parameters, indicating that the algorithm is a good basis for comparison and could potentially be improved with further study.

Proteus in flight over Rosamond Dry lakebed

NASA Image and Video Library

2003-03-27

Scaled Composites' unique tandem-wing Proteus was the testbed for a series of UAV collision-avoidance flight demonstrations. An Amphitech 35GHz radar unit installed below Proteus' nose was the primary sensor for the Detect, See and Avoid tests.

Dynamic clearance measure to evaluate locomotor and perceptuo-motor strategies used for obstacle circumvention in a virtual environment.

PubMed

Darekar, Anuja; Lamontagne, Anouk; Fung, Joyce

2015-04-01

Circumvention around an obstacle entails a dynamic interaction with the obstacle to maintain a safe clearance. We used a novel mathematical interpolation method based on the modified Shepard's method of Inverse Distance Weighting to compute dynamic clearance that reflected this interaction as well as minimal clearance. This proof-of-principle study included seven young healthy, four post-stroke and four healthy age-matched individuals. A virtual environment designed to assess obstacle circumvention was used to administer a locomotor (walking) and a perceptuo-motor (navigation with a joystick) task. In both tasks, participants were asked to navigate towards a target while avoiding collision with a moving obstacle that approached from either head-on, or 30° left or right. Among young individuals, dynamic clearance did not differ significantly between obstacle approach directions in both tasks. Post-stroke individuals maintained larger and smaller dynamic clearance during the locomotor and the perceptuo-motor task respectively as compared to age-matched controls. Dynamic clearance was larger than minimal distance from the obstacle irrespective of the group, task and obstacle approach direction. Also, in contrast to minimal distance, dynamic clearance can respond differently to different avoidance behaviors. Such a measure can be beneficial in contrasting obstacle avoidance behaviors in different populations with mobility problems. Copyright © 2015 Elsevier B.V. All rights reserved.

Adaptive Resampling Particle Filters for GPS Carrier-Phase Navigation and Collision Avoidance System

NASA Astrophysics Data System (ADS)

Hwang, Soon Sik

This dissertation addresses three problems: 1) adaptive resampling technique (ART) for Particle Filters, 2) precise relative positioning using Global Positioning System (GPS) Carrier-Phase (CP) measurements applied to nonlinear integer resolution problem for GPS CP navigation using Particle Filters, and 3) collision detection system based on GPS CP broadcasts. First, Monte Carlo filters, called Particle Filters (PF), are widely used where the system is non-linear and non-Gaussian. In real-time applications, their estimation accuracies and efficiencies are significantly affected by the number of particles and the scheduling of relocating weights and samples, the so-called resampling step. In this dissertation, the appropriate number of particles is estimated adaptively such that the error of the sample mean and variance stay in bounds. These bounds are given by the confidence interval of a normal probability distribution for a multi-variate state. Two required number of samples maintaining the mean and variance error within the bounds are derived. The time of resampling is determined when the required sample number for the variance error crosses the required sample number for the mean error. Second, the PF using GPS CP measurements with adaptive resampling is applied to precise relative navigation between two GPS antennas. In order to make use of CP measurements for navigation, the unknown number of cycles between GPS antennas, the so called integer ambiguity, should be resolved. The PF is applied to this integer ambiguity resolution problem where the relative navigation states estimation involves nonlinear observations and nonlinear dynamics equation. Using the PF, the probability density function of the states is estimated by sampling from the position and velocity space and the integer ambiguities are resolved without using the usual hypothesis tests to search for the integer ambiguity. The ART manages the number of position samples and the frequency of the resampling step for real-time kinematics GPS navigation. The experimental results demonstrate the performance of the ART and the insensitivity of the proposed approach to GPS CP cycle-slips. Third, the GPS has great potential for the development of new collision avoidance systems and is being considered for the next generation Traffic alert and Collision Avoidance System (TCAS). The current TCAS equipment, is capable of broadcasting GPS code information to nearby airplanes, and also, the collision avoidance system using the navigation information based on GPS code has been studied by researchers. In this dissertation, the aircraft collision detection system using GPS CP information is addressed. The PF with position samples is employed for the CP based relative position estimation problem and the same algorithm can be used to determine the vehicle attitude if multiple GPS antennas are used. For a reliable and enhanced collision avoidance system, three dimensional trajectories are projected using the estimates of the relative position, velocity, and the attitude. It is shown that the performance of GPS CP based collision detecting algorithm meets the accuracy requirements for a precise approach of flight for auto landing with significantly less unnecessary collision false alarms and no miss alarms.

Development Of Performance Specifications For Collision Avoidance Systems For Lane Change Merging And Backing, Task 2 - Interim Report: Functional Goals Establishment

DOT National Transportation Integrated Search

1995-02-01

">IN ADDITION TO THE MOST BASIC GOAL OF ELIMINATING THE "BLIND SPOT", SIGNIFICANT CRASH AVOIDANCEOPPORTUNITIES CAN BE REALIZED BY GUARDING AGAINST "FAST CLOSING" VEHICLES DURING LANE CHANGE AND MERGING. THESE "FAST APPROACH" COLLISIONS, THOUGH INFREQ...

Two-Dimensional Distributed Velocity Collision Avoidance

DTIC Science & Technology

2014-02-11

place (i.e., in the global problem space) as much as possible in an effort to simplify the process/description. Additionally, to make some of the...guide agents without collision in the vast majority of cases. NAWCWD TP 8786 31 7.0 REFERENCES 1. P. L. Franchi . “Near Misses Between

Sequential Probability Ratio Test for Collision Avoidance Maneuver Decisions

NASA Technical Reports Server (NTRS)

Carpenter, J. Russell; Markley, F. Landis

2010-01-01

When facing a conjunction between space objects, decision makers must chose whether to maneuver for collision avoidance or not. We apply a well-known decision procedure, the sequential probability ratio test, to this problem. We propose two approaches to the problem solution, one based on a frequentist method, and the other on a Bayesian method. The frequentist method does not require any prior knowledge concerning the conjunction, while the Bayesian method assumes knowledge of prior probability densities. Our results show that both methods achieve desired missed detection rates, but the frequentist method's false alarm performance is inferior to the Bayesian method's

Obstacle Detection and Avoidance System Based on Monocular Camera and Size Expansion Algorithm for UAVs

PubMed Central

Al-Kaff, Abdulla; García, Fernando; Martín, David; De La Escalera, Arturo; Armingol, José María

2017-01-01

One of the most challenging problems in the domain of autonomous aerial vehicles is the designing of a robust real-time obstacle detection and avoidance system. This problem is complex, especially for the micro and small aerial vehicles, that is due to the Size, Weight and Power (SWaP) constraints. Therefore, using lightweight sensors (i.e., Digital camera) can be the best choice comparing with other sensors; such as laser or radar.For real-time applications, different works are based on stereo cameras in order to obtain a 3D model of the obstacles, or to estimate their depth. Instead, in this paper, a method that mimics the human behavior of detecting the collision state of the approaching obstacles using monocular camera is proposed. The key of the proposed algorithm is to analyze the size changes of the detected feature points, combined with the expansion ratios of the convex hull constructed around the detected feature points from consecutive frames. During the Aerial Vehicle (UAV) motion, the detection algorithm estimates the changes in the size of the area of the approaching obstacles. First, the method detects the feature points of the obstacles, then extracts the obstacles that have the probability of getting close toward the UAV. Secondly, by comparing the area ratio of the obstacle and the position of the UAV, the method decides if the detected obstacle may cause a collision. Finally, by estimating the obstacle 2D position in the image and combining with the tracked waypoints, the UAV performs the avoidance maneuver. The proposed algorithm was evaluated by performing real indoor and outdoor flights, and the obtained results show the accuracy of the proposed algorithm compared with other related works. PMID:28481277

Human motion behavior while interacting with an industrial robot.

PubMed

Bortot, Dino; Ding, Hao; Antonopolous, Alexandros; Bengler, Klaus

2012-01-01

Human workers and industrial robots both have specific strengths within industrial production. Advantageously they complement each other perfectly, which leads to the development of human-robot interaction (HRI) applications. Bringing humans and robots together in the same workspace may lead to potential collisions. The avoidance of such is a central safety requirement. It can be realized with sundry sensor systems, all of them decelerating the robot when the distance to the human decreases alarmingly and applying the emergency stop, when the distance becomes too small. As a consequence, the efficiency of the overall systems suffers, because the robot has high idle times. Optimized path planning algorithms have to be developed to avoid that. The following study investigates human motion behavior in the proximity of an industrial robot. Three different kinds of encounters between the two entities under three robot speed levels are prompted. A motion tracking system is used to capture the motions. Results show, that humans keep an average distance of about 0,5m to the robot, when the encounter occurs. Approximation of the workbenches is influenced by the robot in ten of 15 cases. Furthermore, an increase of participants' walking velocity with higher robot velocities is observed.

Toyota drivers' experiences with Dynamic Radar Cruise Control, Pre-Collision System, and Lane-Keeping Assist.

PubMed

Eichelberger, Angela H; McCartt, Anne T

2016-02-01

Advanced crash avoidance and driver assistance technologies potentially can prevent or mitigate many crashes. Previous surveys with drivers have found favorable opinions for many advanced technologies; however, these surveys are not necessarily representative of all drivers or all systems. As the technologies spread throughout the vehicle fleet, it is important to continue studying driver acceptance and use of them. This study focused on 2010-2013 Toyota Sienna and Prius models that were equipped with adaptive cruise control, forward collision avoidance, and lane departure warning and prevention (Prius models only). Telephone interviews were conducted in summer 2013 with 183 owners of vehicles with these technologies. About 9 in 10 respondents wanted adaptive cruise control and forward collision avoidance on their next vehicle, and 71% wanted lane departure warning/prevention again. Males and females reported some differences in their experiences with the systems; for example, males were more likely to have turned on lane departure warning/prevention than females, and when using this system, males reported more frequent warnings than did females. Relative to older drivers, drivers age 40 and younger were more likely to have seen or heard a forward collision warning. Consistent with the results in previous surveys of owners of luxury vehicles, the present survey found that driver acceptance of the technologies was high, although less so for lane departure warning/prevention. Experiences with the Toyota systems differed by driver age and gender to a greater degree than in previous surveys, suggesting that the responses of drivers may begin to differ as crash avoidance technology becomes available on a wider variety of vehicles. Crash avoidance technologies potentially can prevent or mitigate many crashes, but their success depends in part on driver acceptance. These systems will be effective only to the extent that drivers use them. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

Forward collision warning requirements project : refining the CAMP crash alert timing approach by examining "last second" braking and lane change maneuvers under various kinematic conditions

DOT National Transportation Integrated Search

2003-01-01

This final report describes a follow-on study to the previous Crash Avoidance Metrics Partnership (CAMP) human factors work addressing Forward Collision Warning (FCW) timing requirements. This research extends this work by gathering not only "last-se...

Risk management algorithm for rear-side collision avoidance using a combined steering torque overlay and differential braking

NASA Astrophysics Data System (ADS)

Lee, Junyung; Yi, Kyongsu; Yoo, Hyunjae; Chong, Hyokjin; Ko, Bongchul

2015-06-01

This paper describes a risk management algorithm for rear-side collision avoidance. The proposed risk management algorithm consists of a supervisor and a coordinator. The supervisor is designed to monitor collision risks between the subject vehicle and approaching vehicle in the adjacent lane. An appropriate criterion of intervention, which satisfies high acceptance to drivers through the consideration of a realistic traffic, has been determined based on the analysis of the kinematics of the vehicles in longitudinal and lateral directions. In order to assist the driver actively and increase driver's safety, a coordinator is designed to combine lateral control using a steering torque overlay by motor-driven power steering and differential braking by vehicle stability control. In order to prevent the collision while limiting actuator's control inputs and vehicle dynamics to safe values for the assurance of the driver's comfort, the Lyapunov theory and linear matrix inequalities based optimisation methods have been used. The proposed risk management algorithm has been evaluated via simulation using CarSim and MATLAB/Simulink.

A Motion Planning Approach to Automatic Obstacle Avoidance during Concentric Tube Robot Teleoperation

PubMed Central

Torres, Luis G.; Kuntz, Alan; Gilbert, Hunter B.; Swaney, Philip J.; Hendrick, Richard J.; Webster, Robert J.; Alterovitz, Ron

2015-01-01

Concentric tube robots are thin, tentacle-like devices that can move along curved paths and can potentially enable new, less invasive surgical procedures. Safe and effective operation of this type of robot requires that the robot’s shaft avoid sensitive anatomical structures (e.g., critical vessels and organs) while the surgeon teleoperates the robot’s tip. However, the robot’s unintuitive kinematics makes it difficult for a human user to manually ensure obstacle avoidance along the entire tentacle-like shape of the robot’s shaft. We present a motion planning approach for concentric tube robot teleoperation that enables the robot to interactively maneuver its tip to points selected by a user while automatically avoiding obstacles along its shaft. We achieve automatic collision avoidance by precomputing a roadmap of collision-free robot configurations based on a description of the anatomical obstacles, which are attainable via volumetric medical imaging. We also mitigate the effects of kinematic modeling error in reaching the goal positions by adjusting motions based on robot tip position sensing. We evaluate our motion planner on a teleoperated concentric tube robot and demonstrate its obstacle avoidance and accuracy in environments with tubular obstacles. PMID:26413381

A Motion Planning Approach to Automatic Obstacle Avoidance during Concentric Tube Robot Teleoperation.

PubMed

Torres, Luis G; Kuntz, Alan; Gilbert, Hunter B; Swaney, Philip J; Hendrick, Richard J; Webster, Robert J; Alterovitz, Ron

2015-05-01

Concentric tube robots are thin, tentacle-like devices that can move along curved paths and can potentially enable new, less invasive surgical procedures. Safe and effective operation of this type of robot requires that the robot's shaft avoid sensitive anatomical structures (e.g., critical vessels and organs) while the surgeon teleoperates the robot's tip. However, the robot's unintuitive kinematics makes it difficult for a human user to manually ensure obstacle avoidance along the entire tentacle-like shape of the robot's shaft. We present a motion planning approach for concentric tube robot teleoperation that enables the robot to interactively maneuver its tip to points selected by a user while automatically avoiding obstacles along its shaft. We achieve automatic collision avoidance by precomputing a roadmap of collision-free robot configurations based on a description of the anatomical obstacles, which are attainable via volumetric medical imaging. We also mitigate the effects of kinematic modeling error in reaching the goal positions by adjusting motions based on robot tip position sensing. We evaluate our motion planner on a teleoperated concentric tube robot and demonstrate its obstacle avoidance and accuracy in environments with tubular obstacles.

Driving with a partially autonomous forward collision warning system: how do drivers react?

PubMed

Muhrer, Elke; Reinprecht, Klaus; Vollrath, Mark

2012-10-01

The effects of a forward collision warning (FCW) and braking system (FCW+) were examined in a driving simulator study analyzing driving and gaze behavior and the engagement in a secondary task. In-depth accident analyses indicate that a lack of appropriate expectations for possible critical situations and visual distraction may be the major causes of rear-end crashes. Studies with FCW systems have shown that a warning alone was not enough for a driver to be able to avoid the accident. Thus,an additional braking intervention by such systems could be necessary. In a driving simulator experiment, 30 drivers took part in a car-following scenario in an urban area. It was assumed that different lead car behaviors and environmental aspects would lead to different drivers' expectations of the future traffic situation. Driving with and without FCW+ was introduced as a between-subjects factor. Driving with FCW+ resulted in significantly fewer accidents in critical situations. This result was achieved by the system's earlier reaction time as compared with that of drivers. The analysis of the gaze behavior showed that driving with the system did not lead to a stronger involvement in secondary tasks. The study supports the hypotheses about the importance of missing expectations for the occurrence of accidents. These accidents can be prevented by an FCW+ that brakes autonomously. The results indicate that an autonomous braking intervention should be implemented in FCW systems to increase the effectiveness of these assistance systems.

Middle Man Concept for In-Orbit Collision Risks Mitigation, CAESAR and CARA Examples

NASA Technical Reports Server (NTRS)

Moury, Monique; Newman, Lauri K.; Laporte, Francois

2014-01-01

This paper describes the conjunction analysis which has to be performed using data provided by JSpOC. This description not only demonstrates that Collision Avoidance is a 2- step process (close approach detection followed by risk evaluation for collision avoidance decision) but also leads to the conclusion that there is a need for a Middle Man role. After describing the Middle Man concept, this paper introduces two examples with their similarities and particularities: the American civil space effort delivered by the NASA CARA team (Conjunction Assessment Risk Analysis) and the French response CAESAR (Conjunction Assessment and Evaluation Service: Alerts and Recommendations). For both, statistics are presented and feedbacks discussed. All together, around 80 satellites are served by CARA and/or CAESAR. Both processes regularly evolve in order either to follow JSpOC upgrades or to improve analysis according to experience acquired during the past years.

Adaptive Stress Testing of Airborne Collision Avoidance Systems

NASA Technical Reports Server (NTRS)

Lee, Ritchie; Kochenderfer, Mykel J.; Mengshoel, Ole J.; Brat, Guillaume P.; Owen, Michael P.

2015-01-01

This paper presents a scalable method to efficiently search for the most likely state trajectory leading to an event given only a simulator of a system. Our approach uses a reinforcement learning formulation and solves it using Monte Carlo Tree Search (MCTS). The approach places very few requirements on the underlying system, requiring only that the simulator provide some basic controls, the ability to evaluate certain conditions, and a mechanism to control the stochasticity in the system. Access to the system state is not required, allowing the method to support systems with hidden state. The method is applied to stress test a prototype aircraft collision avoidance system to identify trajectories that are likely to lead to near mid-air collisions. We present results for both single and multi-threat encounters and discuss their relevance. Compared with direct Monte Carlo search, this MCTS method performs significantly better both in finding events and in maximizing their likelihood.

Sequential Probability Ratio Test for Collision Avoidance Maneuver Decisions Based on a Bank of Norm-Inequality-Constrained Epoch-State Filters

NASA Technical Reports Server (NTRS)

Carpenter, J. R.; Markley, F. L.; Alfriend, K. T.; Wright, C.; Arcido, J.

2011-01-01

Sequential probability ratio tests explicitly allow decision makers to incorporate false alarm and missed detection risks, and are potentially less sensitive to modeling errors than a procedure that relies solely on a probability of collision threshold. Recent work on constrained Kalman filtering has suggested an approach to formulating such a test for collision avoidance maneuver decisions: a filter bank with two norm-inequality-constrained epoch-state extended Kalman filters. One filter models 1he null hypothesis 1ha1 the miss distance is inside the combined hard body radius at the predicted time of closest approach, and one filter models the alternative hypothesis. The epoch-state filter developed for this method explicitly accounts for any process noise present in the system. The method appears to work well using a realistic example based on an upcoming highly-elliptical orbit formation flying mission.

A real-time robot arm collision avoidance system

NASA Technical Reports Server (NTRS)

Shaffer, Clifford A.; Herb, Gregory M.

1992-01-01

A data structure and update algorithm are presented for a prototype real-time collision avoidance safety system simulating a multirobot workspace. The data structure is a variant of the octree, which serves as a spatial index. An octree recursively decomposes 3D space into eight equal cubic octants until each octant meets some decomposition criteria. The N-objects octree, which indexes a collection of 3D primitive solids is used. These primitives make up the two (seven-degrees-of-freedom) robot arms and workspace modeled by the system. As robot arms move, the octree is updated to reflect their changed positions. During most update cycles, any given primitive does not change which octree nodes it is in. Thus, modification to the octree is rarely required. Cycle time for interpreting current arm joint angles, updating the octree to reflect new positions, and detecting/reporting imminent collisions averages 30 ms on an Intel 80386 processor running at 20 MHz.

Sequential Probability Ratio Test for Spacecraft Collision Avoidance Maneuver Decisions

NASA Technical Reports Server (NTRS)

Carpenter, J. Russell; Markley, F. Landis

2013-01-01

A document discusses sequential probability ratio tests that explicitly allow decision-makers to incorporate false alarm and missed detection risks, and are potentially less sensitive to modeling errors than a procedure that relies solely on a probability of collision threshold. Recent work on constrained Kalman filtering has suggested an approach to formulating such a test for collision avoidance maneuver decisions: a filter bank with two norm-inequality-constrained epoch-state extended Kalman filters. One filter models the null hypotheses that the miss distance is inside the combined hard body radius at the predicted time of closest approach, and one filter models the alternative hypothesis. The epoch-state filter developed for this method explicitly accounts for any process noise present in the system. The method appears to work well using a realistic example based on an upcoming, highly elliptical orbit formation flying mission.

An investigation of collisions between fiber positioning units in LAMOST

NASA Astrophysics Data System (ADS)

Liu, Xiao-Jie; Wang, Gang

2016-04-01

The arrangement of fiber positioning units in the LAMOST focal plane may lead to collisions during the fiber allocation process. To avoid these collisions, a software-based protection system has to abandon some targets located in the overlapping field of adjacent fiber units. In this paper, we first analyze the probability of collisions between fibers and infer their possible reasons. It is useful to solve the problem of collisions among fiber positioning units so as to improve the efficiency of LAMOST. Based on this, a collision handling system is designed by using a master-slave control structure between the micro control unit and microcomputer. Simulated experiments validate that the system can provide real-time inspection and swap information between the fiber unit controllers and the main controller.

Longitudinal driver model and collision warning and avoidance algorithms based on human driving databases

NASA Astrophysics Data System (ADS)

Lee, Kangwon

Intelligent vehicle systems, such as Adaptive Cruise Control (ACC) or Collision Warning/Collision Avoidance (CW/CA), are currently under development, and several companies have already offered ACC on selected models. Control or decision-making algorithms of these systems are commonly evaluated under extensive computer simulations and well-defined scenarios on test tracks. However, they have rarely been validated with large quantities of naturalistic human driving data. This dissertation utilized two University of Michigan Transportation Research Institute databases (Intelligent Cruise Control Field Operational Test and System for Assessment of Vehicle Motion Environment) in the development and evaluation of longitudinal driver models and CW/CA algorithms. First, to examine how drivers normally follow other vehicles, the vehicle motion data from the databases were processed using a Kalman smoother. The processed data was then used to fit and evaluate existing longitudinal driver models (e.g., the linear follow-the-leader model, the Newell's special model, the nonlinear follow-the-leader model, the linear optimal control model, the Gipps model and the optimal velocity model). A modified version of the Gipps model was proposed and found to be accurate in both microscopic (vehicle) and macroscopic (traffic) senses. Second, to examine emergency braking behavior and to evaluate CW/CA algorithms, the concepts of signal detection theory and a performance index suitable for unbalanced situations (few threatening data points vs. many safe data points) are introduced. Selected existing CW/CA algorithms were found to have a performance index (geometric mean of true-positive rate and precision) not exceeding 20%. To optimize the parameters of the CW/CA algorithms, a new numerical optimization scheme was developed to replace the original data points with their representative statistics. A new CW/CA algorithm was proposed, which was found to score higher than 55% in the performance index. This dissertation provides a model of how drivers follow lead-vehicles that is much more accurate than other models in the literature. Furthermore, the data-based approach was used to confirm that a CW/CA algorithm utilizing lead-vehicle braking was substantially more effective than existing algorithms, leading to collision warning systems that are much more likely to contribute to driver safety.

Fuzzy logic path planning system for collision avoidance by an autonomous rover vehicle

NASA Technical Reports Server (NTRS)

Murphy, Michael G.

1993-01-01

The Space Exploration Initiative of the United States will make great demands upon NASA and its limited resources. One aspect of great importance will be providing for autonomous (unmanned) operation of vehicles and/or subsystems in space flight and surface exploration. An additional, complicating factor is that much of the need for autonomy of operation will take place under conditions of great uncertainty or ambiguity. Issues in developing an autonomous collision avoidance subsystem within a path planning system for application in a remote, hostile environment that does not lend itself well to remote manipulation by Earth-based telecommunications is addressed. A good focus is unmanned surface exploration of Mars. The uncertainties involved indicate that robust approaches such as fuzzy logic control are particularly appropriate. Four major issues addressed are (1) avoidance of a fuzzy moving obstacle; (2) backoff from a deadend in a static obstacle environment; (3) fusion of sensor data to detect obstacles; and (4) options for adaptive learning in a path planning system. Examples of the need for collision avoidance by an autonomous rover vehicle on the surface of Mars with a moving obstacle would be wind-blown debris, surface flow or anomalies due to subsurface disturbances, another vehicle, etc. The other issues of backoff, sensor fusion, and adaptive learning are important in the overall path planning system.

SU-E-T-754: Three-Dimensional Patient Modeling Using Photogrammetry for Collision Avoidance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Popple, R; Cardan, R

2015-06-15

Purpose: To evaluate photogrammetry for creating a three-dimensional patient model. Methods: A mannequin was configured on the couch of a CT scanner to simulate a patient setup using an indexed positioning device. A CT fiducial was placed on the indexed CT table-overlay at the reference index position. Two dimensional photogrammetry targets were placed on the table in known positions. A digital SLR camera was used to obtain 27 images from different positions around the CT table. The images were imported into a commercial photogrammetry package and a 3D model constructed. Each photogrammetry target was identified on 2 to 5 images.more » The CT DICOM metadata and the position of the CT fiducial were used to calculate the coordinates of the photogrammetry targets in the CT image frame of reference. The coordinates were transferred to the photogrammetry software to orient the 3D model. The mannequin setup was transferred to the treatment couch of a linear accelerator and positioned at isocenter using in-room lasers. The treatment couch coordinates were noted and compared with prediction. The collision free regions were measured over the full range of gantry and table motion and were compared with predictions obtained using a general purpose polygon interference algorithm. Results: The reconstructed 3D model consisted of 180000 triangles. The difference between the predicted and measured couch positions were 5 mm, 1 mm, and 1 mm for longitudinal, lateral, and vertical, respectively. The collision prediction tested 64620 gantry table combinations in 11.1 seconds. The accuracy was 96.5%, with false positive and negative results occurring at the boundaries of the collision space. Conclusion: Photogrammetry can be used as a tool for collision avoidance during treatment planning. The results indicate that a buffer zone is necessary to avoid false negatives at the boundary of the collision-free zone. Testing with human patients is underway. Research partially supported by a grant from Varian Medical Systems.« less

Fuzzy Logic Path Planning System for Collision Avoidance by an Autonomous Rover Vehicle

NASA Technical Reports Server (NTRS)

Murphy, Michael G.

1991-01-01

Systems already developed at JSC have shown the benefits of applying fuzzy logic control theory to space related operations. Four major issues are addressed that are associated with developing an autonomous collision avoidance subsystem within a path planning system designed for application in a remote, hostile environment that does not lend itself well to remote manipulation of the vehicle involved through Earth-based telecommunication. A good focus for this is unmanned exploration of the surface of Mars. The uncertainties involved indicate that robust approaches such as fuzzy logic control are particularly appropriate. The four major issues addressed are: (1) avoidance of a single fuzzy moving obstacle; (2) back off from a dead end in a static obstacle environment; (3) fusion of sensor data to detect obstacles; and (4) options for adaptive learning in a path planning system.

Effects of roads on habitat quality for bears in the southern Appalachians: A long-term study

USGS Publications Warehouse

Reynolds-Hogland, M. J.; Mitchell, M.S.

2007-01-01

We tested the hypothesis that gravel roads, not paved roads, had the largest negative effect on habitat quality for a population of American black bears (Ursus americanus) that lived in a protected area, where vehicle collision was a relatively minimal source of mortality. We also evaluated whether road use by bears differed by sex or age and whether annual variation in hard mast productivity affected the way bears used areas near roads. In addition, we tested previous findings regarding the spatial extent to which roads affected bear behavior negatively. Using summer and fall home ranges for 118 black bears living in the Pisgah Bear Sanctuary in western North Carolina during 1981-2001, we estimated both home-range-scale (2nd-order) and within-home-range-scale (3rd-order) selection for areas within 250, 500, 800, and 1,600 m of paved and gravel roads. All bears avoided areas near gravel roads more than they avoided areas near paved roads during summer and fall for 2nd-order selection and during summer for 3rd-order selection. During fall, only adult females avoided areas near gravel roads more than they avoided areas near paved roads for 3rd-order selection. We found a positive relationship between use of roads by adults and annual variability in hard mast productivity. Overall, bears avoided areas within 800 m of gravel roads. Future research should determine whether avoidance of gravel roads by bears affects bear survival. ?? 2007 American Society of Mammalogists.

A Compact Magnetic Field-Based Obstacle Detection and Avoidance System for Miniature Spherical Robots.

PubMed

Wu, Fang; Vibhute, Akash; Soh, Gim Song; Wood, Kristin L; Foong, Shaohui

2017-05-28

Due to their efficient locomotion and natural tolerance to hazardous environments, spherical robots have wide applications in security surveillance, exploration of unknown territory and emergency response. Numerous studies have been conducted on the driving mechanism, motion planning and trajectory tracking methods of spherical robots, yet very limited studies have been conducted regarding the obstacle avoidance capability of spherical robots. Most of the existing spherical robots rely on the "hit and run" technique, which has been argued to be a reasonable strategy because spherical robots have an inherent ability to recover from collisions. Without protruding components, they will not become stuck and can simply roll back after running into bstacles. However, for small scale spherical robots that contain sensitive surveillance sensors and cannot afford to utilize heavy protective shells, the absence of obstacle avoidance solutions would leave the robot at the mercy of potentially dangerous obstacles. In this paper, a compact magnetic field-based obstacle detection and avoidance system has been developed for miniature spherical robots. It utilizes a passive magnetic field so that the system is both compact and power efficient. The proposed system can detect not only the presence, but also the approaching direction of a ferromagnetic obstacle, therefore, an intelligent avoidance behavior can be generated by adapting the trajectory tracking method with the detection information. Design optimization is conducted to enhance the obstacle detection performance and detailed avoidance strategies are devised. Experimental results are also presented for validation purposes.

Application of radar for automotive collision avoidance. Volume 2: Development plan and progress reports

NASA Technical Reports Server (NTRS)

Lichtenberg, Christopher L. (Editor)

1987-01-01

The purpose of this project was research and development of an automobile collision avoidance radar system. Items within the scope of the one-year effort were to: (1) review previous authors' work in this field; (2) select a suitable radar approach; (3) develop a system design; (4) perform basic analyses and observations pertinent to radar design, performance, and effects; (5) fabricate and collect radar data from a data collection radar; (6) analyze and derive conclusions from the radar data; and (7) make recommendations about the likelihood of success of the investigated radar techniques. The final technical report presenting all conclusions is contained in Volume 1.

A Summary of the NASA ISS Space Debris Collision Avoidance Program

NASA Technical Reports Server (NTRS)

Frisbee, Joseph

2002-01-01

Creating and implementing a process for the mitigation of the impact hazards due to cornets and asteroids will prove to be a complex and involved process. The closest similar program is the collision avoidance process currently used for protection of the International Space Station (ISS). This process, in operation for over three years, has many similarities to the NEG risk problem. By reviewing the ISS program, a broader perspective on the complications of and requirements for a NEO risk mitigation program might be obtained. Specifically, any lessons learned and continuing issues of concern might prove useful in the development of a NEO risk assessment and mitigation program.

Collision Avoidance for Airport Traffic Simulation Evaluation

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel, Lawrence J., III; Shelton, Kevin J.; Bailey, Randall E.; Otero, Sharon D.; Barker, Glover D.

2010-01-01

A Collision Avoidance for Airport Traffic (CAAT) concept for the airport Terminal Maneuvering Area (TMA) was evaluated in a simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center. CAAT is being designed to enhance surface situation awareness and provide cockpit alerts of potential conflicts during runway, taxi, and low altitude air-to-air operations. The purpose of the study was to evaluate pilot reaction to conflict events in the TMA near the airport, different alert timings for various scenarios, alerting display concepts, and directive alerting concepts. This paper gives an overview of the conflict detection and resolution (CD&R) concept, simulation study, and test results

Collision Avoidance for Airport Traffic Concept Evaluation

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel, Lawrence J., III; Otero, Sharon D.; Barker, Glover D.

2009-01-01

An initial Collision Avoidance for Airport Traffic (CAAT) concept for the Terminal Maneuvering Area (TMA) was evaluated in a simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center. CAAT is being designed to enhance surface situation awareness and provide cockpit alerts of potential conflicts during runway, taxi, and low altitude air-to-air operations. The purpose of the study was to evaluate the initial concept for an aircraft-based method of conflict detection and resolution (CD&R) in the TMA focusing on conflict detection algorithms and alerting display concepts. This paper gives an overview of the CD&R concept, simulation study, and test results.

Advanced Whale Detection Methods to Improve Whale-Ship Collision Avoidance

NASA Astrophysics Data System (ADS)

McGillivary, P. A.; Tougher, B.

2010-12-01

Collisions between whales and ships are now estimated to account for fully a third of all whale deaths worldwide. Such collisions can incur costly ship repairs, and may damage or disable ship steering requiring costly response efforts from state and federal agencies. While collisions with rare whale species are problematic in further reducing their low population numbers, collisions with some of the more abundant whale species are also becoming more common as their populations increase. The problem is compounded as ship traffic likewise continues to grow, thus posing a growing risk to both whales and ships. Federal agencies are considering policies to alter shipping lanes to minimize whale-ship collisions off California and elsewhere. Similar efforts have already been undertaken for the Boston Harbor ship approach, where a bend in the shipping lane was introduced to reduce ship traffic through a favorite area of the highly endangered North Atlantic Right Whale. The Boston shipping approach lane was also flanked with a system of moorings with whale detection hydrophones which broadcast the presence of calling whales in or near the ship channel to approaching ships in real time. When so notified, ships can post lookouts to avoid whale collisions, and reduce speed to reduce the likelihood of whale death, which is highly speed dependent. To reduce the likelihood and seriousness of whale-ship collisions off California and Alaska in particular, there is a need to better know areas of particularly high use by whales, and consider implementation of reduced ship speeds in these areas. There is also an ongoing discussion of altering shipping lanes in the Santa Barbara Channel to avoid habitual Blue whales aggregation areas in particular. However, unlike the case for Boston Harbor, notification of ships that whales are nearby to reduce or avoid collisions is complicated because many California and Alaska whale species do not call regularly, and would thus be undetected by hydrophone arrays. We here discuss the possibility of using Ambient Noise Imaging (ANI) systems initially developed for location of non-calling sperm whales along high speed ferry routes in the Canary Islands. A ‘hybrid’ ANI system has also been developed which uses sound from calling whales to ‘illuminate’ non-calling whales. Such systems designed for sperm whales would require modification for Blue and fin whales along California shipping lanes, and Bowhead whales in Alaska. We discuss how ANI whale detection systems could be developed for California and Alaska by combining bottom moorings with autonomous underwater vehicles (AUVs) and autonomous surface vehicles (ASVs) as part of ocean observing systems. The mechanisms, challenges, and potential solutions for use of ANI whale detection systems along critical shipping lanes along the California and Alaska coast to reduce whale-ship collisions are discussed as a means that permit science to assist in development of integrated state and federal ocean management policies. The combination of new scientific technology with ocean policy decisions can improve coastal ocean management, improve the safety and reduce the cost of shipping, while at the same time protecting endangered whale species.

Robot environment expert system

NASA Technical Reports Server (NTRS)

Potter, J. L.

1985-01-01

The Robot Environment Expert System uses a hexidecimal tree data structure to model a complex robot environment where not only the robot arm moves, but also the robot itself and other objects may move. The hextree model allows dynamic updating, collision avoidance and path planning over time, to avoid moving objects.

Evaluation of the crash mitigation effect of low-speed automated emergency braking systems based on insurance claims data.

PubMed

Isaksson-Hellman, Irene; Lindman, Magdalena

2016-09-01

The aim of the present study was to evaluate the crash mitigation performance of low-speed automated emergency braking collision avoidance technologies by examining crash rates, car damage, and personal injuries. Insurance claims data were used to identify rear-end frontal collisions, the specific situations where the low-speed automated emergency braking system intervenes. We compared cars of the same model (Volvo V70) with and without the low-speed automated emergency braking system (AEB and no AEB, respectively). Distributions of spare parts required for car repair were analyzed to identify car damage, and crash severity was estimated by comparing the results with laboratory crash tests. Repair costs and occupant injuries were investigated for both the striking and the struck vehicle. Rear-end frontal collisions were reduced by 27% for cars with low-speed AEB compared to cars without the system. Those of low severity were reduced by 37%, though more severe crashes were not reduced. Accordingly, the number of injured occupants in vehicles struck by low-speed AEB cars was reduced in low-severity crashes. In offset crash configurations, the system was found to be less effective. This study adds important information about the safety performance of collision avoidance technologies, beyond the number of crashes avoided. By combining insurance claims data and information from spare parts used, the study demonstrates a mitigating effect of low-speed AEB in real-world traffic.

Finding intrinsic rewards by embodied evolution and constrained reinforcement learning.

PubMed

Uchibe, Eiji; Doya, Kenji

2008-12-01

Understanding the design principle of reward functions is a substantial challenge both in artificial intelligence and neuroscience. Successful acquisition of a task usually requires not only rewards for goals, but also for intermediate states to promote effective exploration. This paper proposes a method for designing 'intrinsic' rewards of autonomous agents by combining constrained policy gradient reinforcement learning and embodied evolution. To validate the method, we use Cyber Rodent robots, in which collision avoidance, recharging from battery packs, and 'mating' by software reproduction are three major 'extrinsic' rewards. We show in hardware experiments that the robots can find appropriate 'intrinsic' rewards for the vision of battery packs and other robots to promote approach behaviors.

Dual tasking negatively impacts obstacle avoidance abilities in post-stroke individuals with visuospatial neglect: Task complexity matters!

PubMed

Aravind, Gayatri; Lamontagne, Anouk

2017-01-01

Persons with perceptual-attentional deficits due to visuospatial neglect (VSN) after a stroke are at a risk of collisions while walking in the presence of moving obstacles. The attentional burden of performing a dual-task may further compromise their obstacle avoidance performance, putting them at a greater risk of collisions. The objective of this study was to compare the ability of persons with (VSN+) and without VSN (VSN-) to dual task while negotiating moving obstacles. Twenty-six stroke survivors (13 VSN+, 13 VSN-) were assessed on their ability to (a) negotiate moving obstacles while walking (locomotor single task); (b) perform a pitch-discrimination task (cognitive single task) and (c) simultaneously perform the walking and cognitive tasks (dual task). We compared the groups on locomotor (collision rates, minimum distance from obstacle and onset of strategies) and cognitive (error rates) outcomes. For both single and dual task walking, VSN+ individuals showed higher collision rates compared to VSN- individuals. Dual tasking caused deterioration of locomotor (more collisions, delayed onset and smaller minimum distances) and cognitive performances (higher error rate) in VSN+ individuals. Contrastingly, VSN- individuals maintained collision rates, increased minimum distance, but showed more cognitive errors, prioritizing their locomotor performance. Individuals with VSN demonstrate cognitive-locomotor interference under dual task conditions, which could severely compromise safety when ambulating in community environments and may explain the poor recovery of independent community ambulation in these individuals.

Prevention 0f Unwanted Free-Declaration of Static Obstacles in Probability Occupancy Grids

NASA Astrophysics Data System (ADS)

Krause, Stefan; Scholz, M.; Hohmann, R.

2017-10-01

Obstacle detection and avoidance are major research fields in unmanned aviation. Map based obstacle detection approaches often use discrete world representations such as probabilistic grid maps to fuse incremental environment data from different views or sensors to build a comprehensive representation. The integration of continuous measurements into a discrete representation can result in rounding errors which, in turn, leads to differences between the artificial model and real environment. The cause of these deviations is a low spatial resolution of the world representation comparison to the used sensor data. Differences between artificial representations which are used for path planning or obstacle avoidance and the real world can lead to unexpected behavior up to collisions with unmapped obstacles. This paper presents three approaches to the treatment of errors that can occur during the integration of continuous laser measurement in the discrete probabilistic grid. Further, the quality of the error prevention and the processing performance are compared with real sensor data.

Amplitude modulation of alpha-band rhythm caused by mimic collision: MEG study.

PubMed

Yokosawa, Koichi; Watanabe, Tatsuya; Kikuzawa, Daichi; Aoyama, Gakuto; Takahashi, Makoto; Kuriki, Shinya

2013-01-01

Detection of a collision risk and avoiding the collision are important for survival. We have been investigating neural responses when humans anticipate a collision or intend to take evasive action by applying collision-simulating images in a predictable manner. Collision-simulating images and control images were presented in random order to 9 healthy male volunteers. A cue signal was also given visually two seconds before each stimulus to enable each participant to anticipate the upcoming stimulus. Magnetoencephalograms (MEG) were recorded with a 76-ch helmet system. The amplitude of alpha band (8-13 Hz) rhythm when anticipating the upcoming collision-simulating image was significantly smaller than that when anticipating control images even just after the cue signal. This result demonstrates that anticipating a negative (dangerous) event induced event-related desynchronization (ERD) of alpha band activity, probably caused by attention. The results suggest the feasibility of detecting endogenous brain activities by monitoring alpha band rhythm and its possible applications to engineering systems, such as an automatic collision evasion system for automobiles.

Conflict resolution maneuvers during near miss encounters with cockpit traffic displays

NASA Technical Reports Server (NTRS)

Palmer, E.

1983-01-01

The benefits and liabilities associated with pilots' use of a cockpit traffic display to assess the threat posed by air traffic and to make small maneuvers to avoid situations which would result in collision avoidance advisories are experimentally studied. The crew's task was to fly a simulated wide-body aircraft along a straight course at constant altitude while intruder aircraft appeared on a variety of converging trajectories. The main experimental variables were the amount and quality of the information displayed on the intruder aircraft's estimated future position. Pilots were to maintain a horizontal separation of at least 1.5 nautical miles or a vertical separation of 500 ft, so that collision avoidance advisories would not be triggered. The results show that pilots could usually maneuver to provide the specified separation but often made course deviations greater than 1.5 nm or 500 ft.

Simplified bionic solutions: a simple bio-inspired vehicle collision detection system.

PubMed

Hartbauer, Manfred

2017-02-15

Modern cars are equipped with both active and passive sensor systems that can detect potential collisions. In contrast, locusts avoid collisions solely by responding to certain visual cues that are associated with object looming. In neurophysiological experiments, I investigated the possibility that the 'collision-detector neurons' of locusts respond to impending collisions in films recorded with dashboard cameras of fast driving cars. In a complementary modelling approach, I developed a simple algorithm to reproduce the neuronal response that was recorded during object approach. Instead of applying elaborate algorithms that factored in object recognition and optic flow discrimination, I tested the hypothesis that motion detection restricted to a 'danger zone', in which frontal collisions on the motorways are most likely, is sufficient to estimate the risk of a collision. Furthermore, I investigated whether local motion vectors, obtained from the differential excitation of simulated direction-selective networks, could be used to predict evasive steering maneuvers and prevent undesired responses to motion artifacts. The results of the study demonstrate that the risk of impending collisions in real traffic scenes is mirrored in the excitation of the collision-detecting neuron (DCMD) of locusts. The modelling approach was able to reproduce this neuronal response even when the vehicle was driving at high speeds and image resolution was low (about 200  ×  100 pixels). Furthermore, evasive maneuvers that involved changing the steering direction and steering force could be planned by comparing the differences in the overall excitation levels of the simulated right and left direction-selective networks. Additionally, it was possible to suppress undesired responses of the algorithm to translatory movements, camera shake and ground shadows by evaluating local motion vectors. These estimated collision risk values and evasive steering vectors could be used as input for a driving assistant, converting the first into braking force and the latter into steering responses to avoid collisions. Since many processing steps were computed on the level of pixels and involved elements of direction-selective networks, this algorithm can be implemented in hardware so that parallel computations enhance the processing speed significantly.

Simplified bionic solutions: a simple bio-inspired vehicle collision detection system

PubMed Central

Hartbauer, Manfred

2018-01-01

Modern cars are equipped with both active and passive sensor systems that can detect potential collisions. In contrast, locusts avoid collisions solely by responding to certain visual cues that are associated with object looming. In neurophysiological experiments, I investigated the possibility that the ‘collision-detector neurons’ of locusts respond to impending collisions in films recorded with dashboard cameras of fast driving cars. In a complementary modelling approach, I developed a simple algorithm to reproduce the neuronal response that was recorded during object approach. Instead of applying elaborate algorithms that factored in object recognition and optic flow discrimination, I tested the hypothesis that motion detection restricted to a ‘danger zone’, in which frontal collisions on the motorways are most likely, is sufficient to estimate the risk of a collision. Furthermore, I investigated whether local motion vectors, obtained from the differential excitation of simulated direction-selective networks, could be used to predict evasive steering maneuvers and prevent undesired responses to motion artifacts. The results of the study demonstrate that the risk of impending collisions in real traffic scenes is mirrored in the excitation of the collision-detecting neuron (DCMD) of locusts. The modelling approach was able to reproduce this neuronal response even when the vehicle was driving at high speeds and image resolution was low (about 200 × 100 pixels). Furthermore, evasive maneuvers that involved changing the steering direction and steering force could be planned by comparing the differences in the overall excitation levels of the simulated right and left direction-selective networks. Additionally, it was possible to suppress undesired responses of the algorithm to translatory movements, camera shake and ground shadows by evaluating local motion vectors. These estimated collision risk values and evasive steering vectors could be used as input for a driving assistant, converting the first into braking force and the latter into steering responses to avoid collisions. Since many processing steps were computed on the level of pixels and involved elements of direction-selective networks, this algorithm can be implemented in hardware so that parallel computations enhance the processing speed significantly. PMID:28091394

MD Simulation on Collision Behavior Between Nano-Scale TiO₂ Particles During Vacuum Cold Spraying.

PubMed

Yao, Hai-Long; Yang, Guan-Jun; Li, Chang-Jiu

2018-04-01

Particle collision behavior influences significantly inter-nano particle bonding formation during the nano-ceramic coating deposition by vacuum cold spraying (or aerosol deposition method). In order to illuminate the collision behavior between nano-scale ceramic particles, molecular dynamic simulation was applied to explore impact process between nano-scale TiO2 particles through controlling impact velocities. Results show that the recoil efficiency of the nano-scale TiO2 particle is decreased with the increase of the impact velocity. Nano-scale TiO2 particle exhibits localized plastic deformation during collision at low velocities, while it is intensively deformed by collision at high velocities. This intensive deformation promotes the nano-particle adhesion rather than rebounding off. A relationship between the adhesion energy and the rebound energy is established for the bonding formation of the nano-scale TiO2 particle. The adhesion energy required to the bonding formation between nano-scale ceramic particles can be produced by high velocity collision.

Can use of walkers or canes impede lateral compensatory stepping movements?

PubMed

Bateni, Hamid; Heung, Evelyn; Zettel, John; McLlroy, William E; Maki, Brian E

2004-08-01

Although assistive devices, such as walkers and canes are often prescribed to aid in balance control, recent studies have suggested that such devices may actually increase risk of falling. In this study, we investigated one possible mechanism: the potential for walkers or canes to interfere with, or constrain, lateral movement of the feet and thereby impede execution of compensatory stepping reactions during lateral loss of balance. Lateral stepping reactions were evoked, in 10 healthy young adults (ages 22-27 years), by means of sudden unpredictable medio-lateral support surface translation. Subjects were tested while holding and loading a standard pickup walker or single-tip cane or while using no assistive device (hands free or holding an object). Results supported the hypothesis that using a walker or cane can interfere with compensatory stepping. Collisions between the swing-foot and mobility aid were remarkably frequent when using the walker (60% of stepping reactions) and also occurred in cane trials (11% of stepping reactions). Furthermore, such collisions were associated with a significant reduction (26-37%) in lateral step length. It appeared that subjects were sometimes able to avoid collision by increasing the forward or backward displacement of the swing-foot or by moving the cane; however, attempts to lift the walker out of the way occurred rarely and were usually impeded due to collision between the contralateral walker post and stance foot. The fact that compensatory stepping behavior was altered significantly in such a healthy cohort clearly demonstrates some of the safety limitations inherent to these assistive devices, as currently designed. Copyright 2003 Elsevier B.V.

Florida manatee avoidance technology: A pilot program by the Florida Fish and Wildlife Conservation Commission

NASA Astrophysics Data System (ADS)

Frisch, Katherine; Haubold, Elsa

2003-10-01

Since 1976, approximately 25% of the annual Florida manatee (Trichechus manatus latirostris) mortality has been attributed to collisions with watercraft. In 2001, the Florida Legislature appropriated $200,000 in funds for research projects using technological solutions to directly address the problem of collisions between manatees and watercraft. The Florida Fish & Wildlife Conservation Commission initially funded seven projects for the first two fiscal years. The selected proposals were designed to explore technology that had not previously been applied to the manatee/boat collision problem and included many acoustic concepts related to voice recognition, sonar, and an alerting device to be put on boats to warn manatees. The most promising results to date are from projects employing voice-recognition techniques to identify manatee vocalizations and warn boaters of the manatees' presence. Sonar technology, much like that used in fish finders, is promising but has met with regulatory problems regarding permitting and remains to be tested, as has the manatee-alerting device. The state of Florida found results of the initial years of funding compelling and plans to fund further manatee avoidance technology research in a continued effort to mitigate the problem of manatee/boat collisions.

Feasibility of collision warning, precision approach and landing using GPS, volume 1

NASA Technical Reports Server (NTRS)

Ruedger, W. H.

1981-01-01

The use of GPS, with an appropriately configured data link, to enhance general aviation avionic functions encountered in the terminal area and on approach was investigated with emphasis on approach and landing guidance and collision warning. The feasibility of using differential GPS to obtain the precision navigation solutions required for landing was studied. Results show that the concept is sound. An experimental program was developed to demonstrate this concept. The collision avoidance/warning concept was examined through the development of a functional system specification.

Collision analysis of one kind of chaos-based hash function

NASA Astrophysics Data System (ADS)

Xiao, Di; Peng, Wenbing; Liao, Xiaofeng; Xiang, Tao

2010-02-01

In the last decade, various chaos-based hash functions have been proposed. Nevertheless, the corresponding analyses of them lag far behind. In this Letter, we firstly take a chaos-based hash function proposed very recently in Amin, Faragallah and Abd El-Latif (2009) [11] as a sample to analyze its computational collision problem, and then generalize the construction method of one kind of chaos-based hash function and summarize some attentions to avoid the collision problem. It is beneficial to the hash function design based on chaos in the future.

Interaction dynamics of multiple autonomous mobile robots in bounded spatial domains

NASA Technical Reports Server (NTRS)

Wang, P. K. C.

1989-01-01

A general navigation strategy for multiple autonomous robots in a bounded domain is developed analytically. Each robot is modeled as a spherical particle (i.e., an effective spatial domain about the center of mass); its interactions with other robots or with obstacles and domain boundaries are described in terms of the classical many-body problem; and a collision-avoidance strategy is derived and combined with homing, robot-robot, and robot-obstacle collision-avoidance strategies. Results from homing simulations involving (1) a single robot in a circular domain, (2) two robots in a circular domain, and (3) one robot in a domain with an obstacle are presented in graphs and briefly characterized.

Real-time Collision Avoidance and Path Optimizer for Semi-autonomous UAVs.

NASA Astrophysics Data System (ADS)

Hawary, A. F.; Razak, N. A.

2018-05-01

Whilst UAV offers a potentially cheaper and more localized observation platform than current satellite or land-based approaches, it requires an advance path planner to reveal its true potential, particularly in real-time missions. Manual control by human will have limited line-of-sights and prone to errors due to careless and fatigue. A good alternative solution is to equip the UAV with semi-autonomous capabilities that able to navigate via a pre-planned route in real-time fashion. In this paper, we propose an easy-and-practical path optimizer based on the classical Travelling Salesman Problem and adopts a brute force search method to re-optimize the route in the event of collisions using range finder sensor. The former utilizes a Simple Genetic Algorithm and the latter uses Nearest Neighbour algorithm. Both algorithms are combined to optimize the route and avoid collision at once. Although many researchers proposed various path planning algorithms, we find that it is difficult to integrate on a basic UAV model and often lacks of real-time collision detection optimizer. Therefore, we explore a practical benefit from this approach using on-board Arduino and Ardupilot controllers by manually emulating the motion of an actual UAV model prior to test on the flying site. The result showed that the range finder sensor provides a real-time data to the algorithm to find a collision-free path and eventually optimized the route successfully.

Modeling Driver Behavior near Intersections in Hidden Markov Model

PubMed Central

Li, Juan; He, Qinglian; Zhou, Hang; Guan, Yunlin; Dai, Wei

2016-01-01

Intersections are one of the major locations where safety is a big concern to drivers. Inappropriate driver behaviors in response to frequent changes when approaching intersections often lead to intersection-related crashes or collisions. Thus to better understand driver behaviors at intersections, especially in the dilemma zone, a Hidden Markov Model (HMM) is utilized in this study. With the discrete data processing, the observed dynamic data of vehicles are used for the inference of the Hidden Markov Model. The Baum-Welch (B-W) estimation algorithm is applied to calculate the vehicle state transition probability matrix and the observation probability matrix. When combined with the Forward algorithm, the most likely state of the driver can be obtained. Thus the model can be used to measure the stability and risk of driver behavior. It is found that drivers’ behaviors in the dilemma zone are of lower stability and higher risk compared with those in other regions around intersections. In addition to the B-W estimation algorithm, the Viterbi Algorithm is utilized to predict the potential dangers of vehicles. The results can be applied to driving assistance systems to warn drivers to avoid possible accidents. PMID:28009838

Using artificial intelligence for automating testing of a resident space object collision avoidance system on an orbital spacecraft

NASA Astrophysics Data System (ADS)

Straub, Jeremy

2014-06-01

Resident space objects (RSOs) pose a significant threat to orbital assets. Due to high relative velocities, even a small RSO can cause significant damage to an object that it strikes. Worse, in many cases a collision may create numerous additional RSOs, if the impacted object shatters apart. These new RSOs will have heterogeneous mass, size and orbital characteristics. Collision avoidance systems (CASs) are used to maneuver spacecraft out of the path of RSOs to prevent these impacts. A RSO CAS must be validated to ensure that it is able to perform effectively given a virtually unlimited number of strike scenarios. This paper presents work on the creation of a testing environment and AI testing routine that can be utilized to perform verification and validation activities for cyber-physical systems. It reviews prior work on automated and autonomous testing. Comparative performance (relative to the performance of a human tester) is discussed.

Aerial vehicles collision avoidance using monocular vision

NASA Astrophysics Data System (ADS)

Balashov, Oleg; Muraviev, Vadim; Strotov, Valery

2016-10-01

In this paper image-based collision avoidance algorithm that provides detection of nearby aircraft and distance estimation is presented. The approach requires a vision system with a single moving camera and additional information about carrier's speed and orientation from onboard sensors. The main idea is to create a multi-step approach based on a preliminary detection, regions of interest (ROI) selection, contour segmentation, object matching and localization. The proposed algorithm is able to detect small targets but unlike many other approaches is designed to work with large-scale objects as well. To localize aerial vehicle position the system of equations relating object coordinates in space and observed image is solved. The system solution gives the current position and speed of the detected object in space. Using this information distance and time to collision can be estimated. Experimental research on real video sequences and modeled data is performed. Video database contained different types of aerial vehicles: aircrafts, helicopters, and UAVs. The presented algorithm is able to detect aerial vehicles from several kilometers under regular daylight conditions.

DANTi: Detect and Avoid iN The Cockpit

NASA Technical Reports Server (NTRS)

Chamberlain, James; Consiglio, Maria; Munoz, Cesar

2017-01-01

Mid-air collision risk continues to be a concern for manned aircraft operations, especially near busy non-towered airports. The use of Detect and Avoid (DAA) technologies and draft standards developed for unmanned aircraft systems (UAS), either alone or in combination with other collision avoidance technologies, may be useful in mitigating this collision risk for manned aircraft. This paper describes a NASA research effort known as DANTi (DAA iN The Cockpit), including the initial development of the concept of use, a software prototype, and results from initial flight tests conducted with this prototype. The prototype used a single Automatic Dependent Surveillance - Broadcast (ADS-B) traffic sensor and the own aircraft's position, track, heading and air data information, along with NASA-developed DAA software to display traffic alerts and maneuver guidance to manned aircraft pilots on a portable tablet device. Initial flight tests with the prototype showed a successful DANTi proof-of-concept, but also demonstrated that the traffic separation parameter set specified in the RTCA SC-228 Phase I DAA MOPS may generate excessive false alerts during traffic pattern operations. Several parameter sets with smaller separation values were also tested in flight, one of which yielded more timely alerts for the maneuvers tested. Results from this study may further inform future DANTi efforts as well as Phase II DAA MOPS development.

Design and development of a unit element microstrip antenna for aircraft collision avoidance system

NASA Astrophysics Data System (ADS)

De, Debajit; Sahu, Prasanna Kumar

2017-10-01

Aircraft/traffic alert and collision avoidance system (ACAS/TCAS) is an airborne system which is designed to provide the service as a last defense equipment for avoiding mid-air collisions between the aircraft. In the existing system, four monopole stub-elements are used as ACAS directional antenna and one blade type element is used as ACAS omnidirectional antenna. The existing ACAS antenna has some drawbacks such as low gain, large beamwidth, frequency and beam tuning/scanning issues etc. Antenna issues like unwanted signals reception may create difficulties to identify the possible threats. In this paper, the focus is on the design and development of a unit element microstrip antenna which can be used for ACAS application and to overcome the possible limitations associated with the existing techniques. Two proposed antenna models are presented here, which are single feed and dual feed microstrip dual patch slotted antenna. These are designed and simulated in CST Microwave Studio tool. The performance and other antenna characteristics have been explored from the simulation results followed by the antenna fabrication and measurement. A good reflection coefficient, Voltage Standing Wave Ratio (VSWR), narrow beamwidth, perfect directional radiation pattern, high gain and directivity make this proposed antenna a good candidate for this application.

AIAA Aviation UAS DAA Demonstration-Mini HITL Week 2 Stats

NASA Technical Reports Server (NTRS)

Fern, Lisa Carolynn; Murphy, James R.; Jovic, Srboljub

2016-01-01

The UAS-NAS Project demo will showcase recent research efforts to ensure the interoperability between proposed UAS detect and avoid (DAA) human machine interface requirements (developed within RTCA SC-228) and existing collision avoidance displays. Attendees will be able to view the current state of the art of the DAA pilot traffic, alerting and guidance displays integrated with Traffic advisory and Collision Avoidance (TCAS) II in the UAS-NAS Project's research UAS ground control station (developed in partnership with the Air Force Research Laboratory). In addition, attendees will have the opportunity to interact with the research UAS ground control station and "fly" encounters, using the DAA and TCAS II displays to avoid simulated aircraft. The display of the advisories will be hosted on a laptop with an external 30" monitor, running the Vigilant Spririt system. DAA advisories will be generated by the JADEM software tool, connected to the system via the LVC Gateway. A repeater of the primary flight display will be shown on a 55" tv/monitor mounted on a stand at the back of the booth to show the pilot interaction to the passersby.

UAS-NAS Project Demo - Mini HITL Week 2 Stats

NASA Technical Reports Server (NTRS)

Murphy, James R.; Fern, Lisa C.; Rorie, Robert C.; Shively, Robert; Jovic, Srboljub

2016-01-01

The UAS-NAS Project demo will showcase recent research efforts to ensure the interoperability between proposed UAS detect and avoid (DAA) human machine interface requirements (developed within RTCA SC-228) and existing collision avoidance displays. Attendees will be able to view the current state of the art of the DAA pilot traffic, alerting and guidance displays integrated with Traffic advisory and Collision Avoidance (TCAS) II in the UAS-NAS Project's research UAS ground control station (developed in partnership with the Air Force Research Laboratory). In addition, attendees will have the opportunity to interact with the research UAS ground control station and "fly" encounters, using the DAA and TCAS II displays to avoid simulated aircraft. The display of the advisories will be hosted on a laptop with an external 30" monitor, running the Vigilant Spirit system. DAA advisories will be generated by the JADEM software tool, connected to the system via the LVC Gateway. A repeater of the primary flight display will be shown on a 55" monitor mounted on a stand at the back of the booth to show the pilot interaction to the passersby.

Thermal Photon Radiation in High Multiplicity p + Pb Collisions at the Large Hadron Collider

DOE PAGES

Shen, Chun; Paquet, Jean-François; Denicol, Gabriel S.; ...

2016-02-18

We observed the collective behavior of hadronic particles in high multiplicity proton-lead collisions at the Large Hadron Collider, as well as in deuteron-gold collisions at the Relativistic Heavy-Ion Collider. In our work we present the first calculation, in the hydrodynamic framework, of thermal photon radiation from such small collision systems. Owing to their compact size, these systems can reach temperatures comparable to those in central nucleus-nucleus collisions. Moreover, the thermal photons can thus shine over the prompt background, and increase the low p T direct photon spectrum by a factor of 2–3 in 0%–1% p+Pb collisions at 5.02 TeV. Thismore » thermal photon enhancement can therefore serve as a signature of the existence of a hot quark-gluon plasma during the evolution of these small collision systems, as well as validate hydrodynamic behavior in small systems.« less

Universal behavior of charged particle production in heavy ion collisions

NASA Astrophysics Data System (ADS)

Phobos Collaboration; Steinberg, Peter A.; Back, B. B.; Baker, M. D.; Barton, D. S.; Betts, R. R.; Ballintijn, M.; Bickley, A. A.; Bindel, R.; Budzanowski, A.; Busza, W.; Carroll, A.; Decowski, M. P.; Garcia, E.; George, N.; Gulbrandsen, K.; Gushue, S.; Halliwell, C.; Hamblen, J.; Heintzelman, G. A.; Henderson, C.; Hofman, D. J.; Hollis, R. S.; Hołński, R.; Holzman, B.; Iordanova, A.; Johnson, E.; Kane, J. L.; Katzy, J.; Khan, N.; Kucewicz, W.; Kulinich, P.; Kuo, C. M.; Lin, W. T.; Manly, S.; McLeod, D.; Michałowski, J.; Mignerey, A. C.; Nouicer, R.; Olszewski, A.; Pak, R.; Park, I. C.; Pernegger, H.; Reed, C.; Remsberg, L. P.; Reuter, M.; Roland, C.; Roland, G.; Rosenberg, L.; Sagerer, J.; Sarin, P.; Sawicki, P.; Skulski, W.; Steadman, S. G.; Steinberg, P.; Stephans, G. S. F.; Stodulski, M.; Sukhanov, A.; Tang, J.-L.; Teng, R.; Trzupek, A.; Vale, C.; van Nieuwenhuizen, G. J.; Verdier, R.; Wadsworth, B.; Wolfs, F. L. H.; Wosiek, B.; Woźniak, K.; Wuosmaa, A. H.; Wysłouch, B.

2003-03-01

The PHOBOS experiment at RHIC has measured the multiplicity of primary charged particles as a function of centrality and pseudorapidity in Au+Au collisions at sqrt(s_NN) = 19.6, 130 and 200 GeV. Two kinds of universal behavior are observed in charged particle production in heavy ion collisions. The first is that forward particle production, over a range of energies, follows a universal limiting curve with a non-trivial centrality dependence. The second arises from comparisons with pp/pbar-p and e+e- data. N_tot/(N_part/2) in nuclear collisions at high energy scales with sqrt(s) in a similar way as N_tot in e+e- collisions and has a very weak centrality dependence. This feature may be related to a reduction in the leading particle effect due to the multiple collisions suffered per participant in heavy ion collisions.

Universal behavior of charged particle production in heavy ion collisions at RHIC energies

NASA Astrophysics Data System (ADS)

Steinberg, Peter A.; Back, B. B.; Baker, M. D.; Barton, D. S.; Betts, R. R.; Ballintijn, M.; Bickley, A. A.; Bindel, R.; Budzanowski, A.; Busza, W.; Carroll, A.; Decowski, M. P.; García, E.; George, N.; Gulbrandsen, K.; Gushue, S.; Halliwell, C.; Hamblen, J.; Heintzelman, G. A.; Henderson, C.; Hofman, D. J.; Hollis, R. S.; Holyński, R.; Holzman, B.; Iordanova, A.; Johnson, E.; Kane, J. L.; Katzy, J.; Khan, N.; Kucewicz, W.; Kulinich, P.; Kuo, C. M.; Lin, W. T.; Manly, S.; McLeod, D.; Michałowski, J.; Mignerey, A. C.; Nouicer, R.; Olszewski, A.; Pak, R.; Park, I. C.; Pernegger, H.; Reed, C.; Remsberg, L. P.; Reuter, M.; Roland, C.; Roland, G.; Rosenberg, L.; Sagerer, J.; Sarin, P.; Sawicki, P.; Skulski, W.; Steadman, S. G.; Steinberg, P.; Stephans, G. S. F.; Stodulski, M.; Sukhanov, A.; Tang, J.-L.; Teng, R.; Trzupek, A.; Vale, C.; van Nieuwenhuizen, G. J.; Verdier, R.; Wadsworth, B.; Wolfs, F. L. H.; Wosiek, B.; Woźniak, K.; Wuosmaa, A. H.; Wysłouch, B.; Phobos Collaboration

2003-04-01

The PHOBOS experiment at RHIC has measured the multiplicity of primary charged particles as a function of centrality and pseudorapidity in Au+Au collisions at √ SNN = 19.6, 130 and 200 GeV. Two kinds of universal behavior are observed in charged particle production in heavy ion collisions. The first is that forward particle production, over a range of energies, follows a universal limiting curve with a non-trivial centrality dependence. The second arises from comparisons with pp/ overlinepp and e +e - data. < Nch>/< Npart/2> in nuclear collisions at high energy scales with √ s in a similar way as Nch in e +e - collisions and has a very weak centrality dependence. This feature may be related to a reduction in the leading particle effect due to the multiple collisions suffered per participant in heavy ion collisions.

Collision avoidance for aircraft in abort landing

NASA Astrophysics Data System (ADS)

Mathwig, Jarret

We study the collision avoidance between two aircraft flying in the same vertical plane: a host aircraft on a glide path and an intruder aircraft on a horizontal trajectory below that of the host aircraft and heading in the opposite direction. Assuming that the intruder aircraft is uncooperative, the host aircraft executes an optimal abort landing maneuver: it applies maximum thrust setting and maximum angle of attack lifting the flight path over the original path, thereby increasing the timewise minimum distance between the two aircraft and, in this way, avoiding the potential collision. In the presence of weak constraints on the aircraft and/or the environment, the angle of attack must be brought to the maximum value and kept there until the maximin point is reached. On the other hand, in the presence of strong constraints on the aircraft and the environment, desaturation of the angle of attack might have to take place before the maximin point is reached. This thesis includes four parts. In the first part, after an introduction and review of the available literature, we reformulate and solve the one-subarc Chebyshev maximin problem as a two-subarc Bolza-Pontryagin problem in which the avoidance and the recovery maneuvers are treated simultaneously. In the second part, we develop a guidance scheme (gamma guidance) capable of approximating the optimal trajectory in real time. In the third part, we present the algorithms employed to solve the one-subarc and two-subarc problems. In the fourth part, we decompose the two-subarc Bolza-Pontryagin problem into two one-subarc problems: the avoidance problem and the recovery problem, to be solved in sequence; remarkably, for problems where the ratio of total maneuver time to avoidance time is sufficiently large (≥5), this simplified procedure predicts accurately the location of the maximin point as well as the maximin distance.

Discrepancy analysis of driving performance of taxi drivers and non-professional drivers for red-light running violation and crash avoidance at intersections.

PubMed

Wu, Jiawei; Yan, Xuedong; Radwan, Essam

2016-06-01

Due to comfort, convenience, and flexibility, taxis have become increasingly more prevalent in China, especially in large cities. However, many violations and road crashes that occurred frequently were related to taxi drivers. This study aimed to investigate differences in driving performance between taxi drivers and non-professional drivers from the perspectives of red-light running violation and potential crash involvement based on a driving simulation experiment. Two typical scenarios were established in a driving simulator, which includes the red-light running violation scenario and the crash avoidance scenario. There were 49 participants, including 23 taxi drivers (14 males and 9 females) and 26 non-professional drivers (13 males and 13 females) recruited for this experiment. The driving simulation experiment results indicated that non-professional drivers paid more attention to red-light running violations in comparison to taxi drivers who had a higher probability of red-light running violation. Furthermore, it was found that taxi drivers were more inclined to turn the steering wheel in an attempt to avoid a potential collision and non-professional drivers had more abrupt deceleration behaviors when facing a potential crash. Moreover, the experiment results showed that taxi drivers had a smaller crash rate compared to non-professional drivers and had a better performance in terms of crash avoidance at the intersection. Copyright © 2016 Elsevier Ltd. All rights reserved.

Counterfactual simulations applied to SHRP2 crashes: The effect of driver behavior models on safety benefit estimations of intelligent safety systems.

PubMed

Bärgman, Jonas; Boda, Christian-Nils; Dozza, Marco

2017-05-01

As the development and deployment of in-vehicle intelligent safety systems (ISS) for crash avoidance and mitigation have rapidly increased in the last decades, the need to evaluate their prospective safety benefits before introduction has never been higher. Counterfactual simulations using relevant mathematical models (for vehicle dynamics, sensors, the environment, ISS algorithms, and models of driver behavior) have been identified as having high potential. However, although most of these models are relatively mature, models of driver behavior in the critical seconds before a crash are still relatively immature. There are also large conceptual differences between different driver models. The objective of this paper is, firstly, to demonstrate the importance of the choice of driver model when counterfactual simulations are used to evaluate two ISS: Forward collision warning (FCW), and autonomous emergency braking (AEB). Secondly, the paper demonstrates how counterfactual simulations can be used to perform sensitivity analyses on parameter settings, both for driver behavior and ISS algorithms. Finally, the paper evaluates the effect of the choice of glance distribution in the driver behavior model on the safety benefit estimation. The paper uses pre-crash kinematics and driver behavior from 34 rear-end crashes from the SHRP2 naturalistic driving study for the demonstrations. The results for FCW show a large difference in the percent of avoided crashes between conceptually different models of driver behavior, while differences were small for conceptually similar models. As expected, the choice of model of driver behavior did not affect AEB benefit much. Based on our results, researchers and others who aim to evaluate ISS with the driver in the loop through counterfactual simulations should be sure to make deliberate and well-grounded choices of driver models: the choice of model matters. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ungulate Vehicle Collisions in a Peri-Urban Environment: Consequences of Transportation Infrastructures Planned Assuming the Absence of Ungulates

PubMed Central

Zuberogoitia, Iñigo; del Real, Javier; Torres, Juan José; Rodríguez, Luis; Alonso, María; Zabala, Jabi

2014-01-01

Ungulate vehicle collisions (UVC) provoke serious damage, including human casualties, and a large number of measures have been developed around the world to avoid collisions. We analyse the main factors involved in UVC in a road network built in the absence of ungulates, where mitigation structures to avoid UVC were not adequately considered. Ungulate population greatly increased during the last two decades and now Roe Deer and Wild Boars are widely distributed over the study area, but even after this increase, the road network was not adapted to avoid UVC. A total of 235 Roe Deer (RDVC) and 153 Wild Boar vehicle collisions (WBVC) were recorded between January 2008 and December 2011. We randomly selected 289 sample points (87 RDVC, 60 WBVC and 142 controls) separated by at least 500 metres from the next closest point and measured 19 variables that could potentially influence the vehicle collisions. We detected variations in the frequency of RDVC on a monthly basis, and WBVC was higher at weekends but no significant differences were detected on a monthly basis. UVC were more likely to occur at locations where sinuosity of the road, velocity, surface of shrub and deciduous forest area were greater, the presence of fences entered with positive relationship and distance to the nearest building was less. RDVC were more likely to occur at locations where timber forest area increased and distance to the nearest building decreased and WBVC was related to open fields cover and also to the presence of fences. Sinuosity and velocity entered in both cases as significant factors. Major roads, in which the traffic volume is greater and faster, caused more accidents with ungulates than secondary roads. Nowadays, the high frequency of ungulate road-kills deserves a new strategy in order to adapt infrastructure and adopt mitigation measures. PMID:25251376

Ungulate vehicle collisions in a peri-urban environment: consequences of transportation infrastructures planned assuming the absence of ungulates.

PubMed

Zuberogoitia, Iñigo; del Real, Javier; Torres, Juan José; Rodríguez, Luis; Alonso, María; Zabala, Jabi

2014-01-01

Ungulate vehicle collisions (UVC) provoke serious damage, including human casualties, and a large number of measures have been developed around the world to avoid collisions. We analyse the main factors involved in UVC in a road network built in the absence of ungulates, where mitigation structures to avoid UVC were not adequately considered. Ungulate population greatly increased during the last two decades and now Roe Deer and Wild Boars are widely distributed over the study area, but even after this increase, the road network was not adapted to avoid UVC. A total of 235 Roe Deer (RDVC) and 153 Wild Boar vehicle collisions (WBVC) were recorded between January 2008 and December 2011. We randomly selected 289 sample points (87 RDVC, 60 WBVC and 142 controls) separated by at least 500 metres from the next closest point and measured 19 variables that could potentially influence the vehicle collisions. We detected variations in the frequency of RDVC on a monthly basis, and WBVC was higher at weekends but no significant differences were detected on a monthly basis. UVC were more likely to occur at locations where sinuosity of the road, velocity, surface of shrub and deciduous forest area were greater, the presence of fences entered with positive relationship and distance to the nearest building was less. RDVC were more likely to occur at locations where timber forest area increased and distance to the nearest building decreased and WBVC was related to open fields cover and also to the presence of fences. Sinuosity and velocity entered in both cases as significant factors. Major roads, in which the traffic volume is greater and faster, caused more accidents with ungulates than secondary roads. Nowadays, the high frequency of ungulate road-kills deserves a new strategy in order to adapt infrastructure and adopt mitigation measures.

Dangerous student car drop-off behaviors and child pedestrian-motor vehicle collisions: An observational study.

PubMed

Rothman, Linda; Howard, Andrew; Buliung, Ron; Macarthur, Colin; Macpherson, Alison

2016-07-03

The objective of this study was to examine the association between dangerous student car drop-off behaviors and historical child pedestrian-motor vehicle collisions (PMVCs) near elementary schools in Toronto, Canada. Police-reported child PMVCs during school travel times from 2000 to 2011 were mapped within 200 m of 118 elementary schools. Observers measured dangerous student morning car drop-off behaviors and number of children walking to school during one day in 2011. A composite score of school social disadvantage was obtained from the Toronto District School Board. Built environment and traffic features were mapped and included as covariates. A multivariate Poisson regression was used to model the rates of PMVC/number of children walking and dangerous student car drop-off behaviors, adjusting for the built environment and social disadvantage. There were 45 child PMVCs, with 29 (64%) sustaining minor injuries resulting in emergency department visits. The mean collision rate was 2.9/10,000 children walking/year (SD = 6.7). Dangerous drop-off behaviors were observed in 104 schools (88%). In the multivariate analysis, each additional dangerous drop-off behavior was associated with a 45% increase in collision rates (incident rate ratio [IRR] = 1.45, 95% confidence interval [CI], 1.02, 2.07). Higher speed roads (IRR = 1.27, 95% CI, 1.13, 1.44) and social disadvantage (IRR = 2.99, 95% CI, 1.03, 8.68) were associated with higher collision rates. Dangerous student car drop-off behaviors were associated with historical nonfatal child PMVC rates during school travel times near schools. Some caution must be taken in interpreting these results due small number of events and limitations in the data collection, because collision data were collected historically over a 12-year period, whereas driving behavior was only observed on a single day in 2011. Targeted multifaceted intervention approaches related to the built environment, enforcement, and education could address dangerous drop-off behaviors near schools to reduce child PMVCs and promote safe walking to school.

Digital-Difference Processing For Collision Avoidance.

NASA Technical Reports Server (NTRS)

Shores, Paul; Lichtenberg, Chris; Kobayashi, Herbert S.; Cunningham, Allen R.

1988-01-01

Digital system for automotive crash avoidance measures and displays difference in frequency between two sinusoidal input signals of slightly different frequencies. Designed for use with Doppler radars. Characterized as digital mixer coupled to frequency counter measuring difference frequency in mixer output. Technique determines target path mathematically. Used for tracking cars, missiles, bullets, baseballs, and other fast-moving objects.

Trust-Based Analysis of an Air Force Collision Avoidance System

DTIC Science & Technology

2015-12-01

that test pilots’ trust depended on a number of factors, including the development of a nuisance free algorithm, designing fly-up evasive maneuvers...revealed that test pilots’ trust depended on a number of factors, including the development of a nuisance- free algorithm, designing fly-up evasive ...the terrain collision evasion maneuver. To overcome these limitations, Auto-GCAS was developed with a number of innovative approaches and solutions

Range Sensor-Based Efficient Obstacle Avoidance through Selective Decision-Making.

PubMed

Shim, Youngbo; Kim, Gon-Woo

2018-03-29

In this paper, we address a collision avoidance method for mobile robots. Many conventional obstacle avoidance methods have been focused solely on avoiding obstacles. However, this can cause instability when passing through a narrow passage, and can also generate zig-zag motions. We define two strategies for obstacle avoidance, known as Entry mode and Bypass mode. Entry mode is a pattern for passing through the gap between obstacles, while Bypass mode is a pattern for making a detour around obstacles safely. With these two modes, we propose an efficient obstacle avoidance method based on the Expanded Guide Circle (EGC) method with selective decision-making. The simulation and experiment results show the validity of the proposed method.

Avian behavior and mortality at power lines in coastal South Carolina

USGS Publications Warehouse

Savereno, A.J.; Savereno, L.A.; Boettcher, R.; Haig, S.M.

1996-01-01

We compared avian behavior and mortality associated with two 115-kV transmission lines on the central South Carolina coast during 3,392 hours of observation from May 1991 through May 1994. One line was marked with 30-cm-diameter yellow aviation markers. The second line was unmarked, but was similar in most other aspects. We conducted ground searches (n = 445) beneath each line year-round to document avian mortality due to power-line collisions. At marked lines, birds that approached at line height changed behavior more at unmarked lines (P< 0.001), and fewer crossed between static and conductor wires. Collision rate was 53% lower at marked than unmarked lines. Among collisions at both sites, 82% of birds collided with static wires. Based on observed collisions and carcass recoveries, wading birds particularly appeared to be at risk. We concluded that aviation markers were effective at increasing line visibility and reducing collisions and recommend marking static wires of power lines in potentially sensitive areas.

An Algorithm for Autonomous Formation Obstacle Avoidance

NASA Astrophysics Data System (ADS)

Cruz, Yunior I.

The level of human interaction with Unmanned Aerial Systems varies greatly from remotely piloted aircraft to fully autonomous systems. In the latter end of the spectrum, the challenge lies in designing effective algorithms to dictate the behavior of the autonomous agents. A swarm of autonomous Unmanned Aerial Vehicles requires collision avoidance and formation flight algorithms to negotiate environmental challenges it may encounter during the execution of its mission, which may include obstacles and chokepoints. In this work, a simple algorithm is developed to allow a formation of autonomous vehicles to perform point to point navigation while avoiding obstacles and navigating through chokepoints. Emphasis is placed on maintaining formation structures. Rather than breaking formation and individually navigating around the obstacle or through the chokepoint, vehicles are required to assemble into appropriately sized/shaped sub-formations, bifurcate around the obstacle or negotiate the chokepoint, and reassemble into the original formation at the far side of the obstruction. The algorithm receives vehicle and environmental properties as inputs and outputs trajectories for each vehicle from start to the desired ending location. Simulation results show that the algorithm safely routes all vehicles past the obstruction while adhering to the aforementioned requirements. The formation adapts and successfully negotiates the obstacles and chokepoints in its path while maintaining proper vehicle separation.

Motorcyclists safety system to avoid rear end collisions based on acoustic signatures

NASA Astrophysics Data System (ADS)

Muzammel, M.; Yusoff, M. Zuki; Malik, A. Saeed; Mohamad Saad, M. Naufal; Meriaudeau, F.

2017-03-01

In many Asian countries, motorcyclists have a higher fatality rate as compared to other vehicles. Among many other factors, rear end collisions are also contributing for these fatalities. Collision detection systems can be useful to minimize these accidents. However, the designing of efficient and cost effective collision detection system for motorcyclist is still a major challenge. In this paper, an acoustic information based, cost effective and efficient collision detection system is proposed for motorcycle applications. The proposed technique uses the Short time Fourier Transform (STFT) to extract the features from the audio signal and Principal component analysis (PCA) has been used to reduce the feature vector length. The reduction of feature length, further increases the performance of this technique. The proposed technique has been tested on self recorded dataset and gives accuracy of 97.87%. We believe that this method can help to reduce a significant number of motorcycle accidents.

Distance estimation and collision prediction for on-line robotic motion planning

NASA Technical Reports Server (NTRS)

Kyriakopoulos, K. J.; Saridis, G. N.

1991-01-01

An efficient method for computing the minimum distance and predicting collisions between moving objects is presented. This problem has been incorporated in the framework of an in-line motion planning algorithm to satisfy collision avoidance between a robot and moving objects modeled as convex polyhedra. In the beginning the deterministic problem, where the information about the objects is assumed to be certain is examined. If instead of the Euclidean norm, L(sub 1) or L(sub infinity) norms are used to represent distance, the problem becomes a linear programming problem. The stochastic problem is formulated, where the uncertainty is induced by sensing and the unknown dynamics of the moving obstacles. Two problems are considered: (1) filtering of the minimum distance between the robot and the moving object, at the present time; and (2) prediction of the minimum distance in the future, in order to predict possible collisions with the moving obstacles and estimate the collision time.

Universal hydrodynamic flow in holographic planar shock collisions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chesler, Paul M.; Kilbertus, Niki; van der Schee, Wilke

2015-11-20

We study the collision of planar shock waves in AdS 5 as a function of shock profile. In the dual field theory the shock waves describe planar sheets of energy whose collision results in the formation of a plasma which behaves hydrodynamically at late times. We find that the post-collision stress tensor near the light cone exhibits transient non-universal behavior which depends on both the shock width and the precise functional form of the shock profile. However, over a large range of shock widths, including those which yield qualitative different behavior near the future light cone, and for different shockmore » profiles, we find universal behavior in the subsequent hydrodynamic evolution. In addition, we compute the rapidity distribution of produced particles and find it to be well described by a Gaussian.« less

A Neural Model of Visually Guided Steering, Obstacle Avoidance, and Route Selection

ERIC Educational Resources Information Center

Elder, David M.; Grossberg, Stephen; Mingolla, Ennio

2009-01-01

A neural model is developed to explain how humans can approach a goal object on foot while steering around obstacles to avoid collisions in a cluttered environment. The model uses optic flow from a 3-dimensional virtual reality environment to determine the position of objects on the basis of motion discontinuities and computes heading direction,…

Traffic jam driving with NMV avoidance

NASA Astrophysics Data System (ADS)

Milanés, Vicente; Alonso, Luciano; Villagrá, Jorge; Godoy, Jorge; de Pedro, Teresa; Oria, Juan P.

2012-08-01

In recent years, the development of advanced driver assistance systems (ADAS) - mainly based on lidar and cameras - has considerably improved the safety of driving in urban environments. These systems provide warning signals for the driver in the case that any unexpected traffic circumstance is detected. The next step is to develop systems capable not only of warning the driver but also of taking over control of the car to avoid a potential collision. In the present communication, a system capable of autonomously avoiding collisions in traffic jam situations is presented. First, a perception system was developed for urban situations—in which not only vehicles have to be considered, but also pedestrians and other non-motor-vehicles (NMV). It comprises a differential global positioning system (DGPS) and wireless communication for vehicle detection, and an ultrasound sensor for NMV detection. Then, the vehicle's actuators - brake and throttle pedals - were modified to permit autonomous control. Finally, a fuzzy logic controller was implemented capable of analyzing the information provided by the perception system and of sending control commands to the vehicle's actuators so as to avoid accidents. The feasibility of the integrated system was tested by mounting it in a commercial vehicle, with the results being encouraging.

Modeling and simulation of cars in frontal collision

NASA Astrophysics Data System (ADS)

Deac, S. C.; Perescu, A.; Simoiu, D.; Nyaguly, E.; Crâştiu, I.; Bereteu, L.

2018-01-01

Protection of cars, mainly drivers and passengers in a collision are very important issues worldwide. Statistics given by “World Health Organization” are alarming rate of increase in the number of road accidents, most claiming with serious injury, human and material loss. For these reasons has been a continuous development of protection systems, especially car causing three quarters of all accidents. Mathematical modeling and simulation of a car behavior during a frontal collision leads to new solutions in the development of protective systems. This paper presents several structural models of a vehicle during a frontal collision and its behavior is analyzed by numerical simulation using Simulink.

Scaled Composites' Proteus aircraft and an F/A-18 Hornet from NASA's Dryden Flight Research Center d

NASA Technical Reports Server (NTRS)

2002-01-01

Scaled Composites' Proteus aircraft and an F/A-18 Hornet from NASA's Dryden Flight Research Center during a low-level flyby at Las Cruces Airport in New Mexico. The unique Proteus aircraft served as a test bed for NASA-sponsored flight tests designed to validate collision-avoidance technologies proposed for uninhabited aircraft. The tests, flown over southern New Mexico in March, 2002, used the Proteus as a surrogate uninhabited aerial vehicle (UAV) while three other aircraft flew toward the Proteus from various angles on simulated collision courses. Radio-based 'detect, see and avoid' equipment on the Proteus successfully detected the other aircraft and relayed that information to a remote pilot on the ground at Las Cruces Airport. The pilot then transmitted commands to the Proteus to maneuver it away from the potential collisions. The flight demonstration, sponsored by NASA Dryden Flight Research Center, New Mexico State University, Scaled Composites, the U.S. Navy and Modern Technology Solutions, Inc., were intended to demonstrate that UAVs can be flown safely and compatibly in the same skies as piloted aircraft.

A Geometric Analysis to Protect Manned Assets from Newly Launched Objects - Cola Gap Analysis

NASA Technical Reports Server (NTRS)

Hametz, Mark E.; Beaver, Brian A.

2013-01-01

A safety risk was identified for the International Space Station (ISS) by The Aerospace Corporation, where the ISS would be unable to react to a conjunction with a newly launched object following the end of the launch Collision Avoidance (COLA) process. Once an object is launched, there is a finite period of time required to track, catalog, and evaluate that new object as part of standard onorbit COLA screening processes. Additionally, should a conjunction be identified, there is an additional period of time required to plan and execute a collision avoidance maneuver. While the computed prelaunch probability of collision with any object is extremely low, NASA/JSC has requested that all US launches take additional steps to protect the ISS during this "COLA gap" period. This paper details a geometric-based COLA gap analysis method developed by the NASA Launch Services Program to determine if launch window cutouts are required to mitigate this risk. Additionally, this paper presents the results of several missions where this process has been used operationally.

Interactive-rate Motion Planning for Concentric Tube Robots.

PubMed

Torres, Luis G; Baykal, Cenk; Alterovitz, Ron

2014-05-01

Concentric tube robots may enable new, safer minimally invasive surgical procedures by moving along curved paths to reach difficult-to-reach sites in a patient's anatomy. Operating these devices is challenging due to their complex, unintuitive kinematics and the need to avoid sensitive structures in the anatomy. In this paper, we present a motion planning method that computes collision-free motion plans for concentric tube robots at interactive rates. Our method's high speed enables a user to continuously and freely move the robot's tip while the motion planner ensures that the robot's shaft does not collide with any anatomical obstacles. Our approach uses a highly accurate mechanical model of tube interactions, which is important since small movements of the tip position may require large changes in the shape of the device's shaft. Our motion planner achieves its high speed and accuracy by combining offline precomputation of a collision-free roadmap with online position control. We demonstrate our interactive planner in a simulated neurosurgical scenario where a user guides the robot's tip through the environment while the robot automatically avoids collisions with the anatomical obstacles.

Occupant injury protection in automobile collisions.

PubMed

Peters, G A; Peters, B J

1999-12-01

Modern technology has produced automotive vehicles that have become both a luxury and a necessity in modern civilization. They have become highly useful, even more varied in form and function, and capable of high speeds on crowded roadways. One unfortunate consequence is the high frequency of accidents and the greater severity of injuries when collisions do occur. In response, modern technology has produced a variety of safety and health features, devices and designs intended for better occupant protection on in high speed vehicles. Injury reduction has become a prime design objective, but there are residual risks, which, as technology evolves, require effective communication to those risk. There can be little risk avoidance behavior without awareness of the hazards and effective communication to the vehicle occupant, as to what could and should be done for self-protection. For example, one out of three drivers apparently fails to understand the function of head restraints, few understand the 'safe zone' posture required for air bags and many believe safety features should be adjusted only for comfort. Some of the current residual injury producing problems in occupant systems are specifically described here in order to illustrate what is needed in terms of both design remedies and health promotion activities.

Intelligent Vehicle Initiative : business plan

DOT National Transportation Integrated Search

1997-11-01

Ongoing and recently completed research and development indicate that collision avoidance systems offer the potential for significantly reducing motor vehicle crashes. Preliminary estimates by the National Highway Traffic Safety Administration (NHTSA...

An Intelligent Robotic Hospital Bed for Safe Transportation of Critical Neurosurgery Patients Along Crowded Hospital Corridors.

PubMed

Wang, Chao; Savkin, Andrey V; Clout, Ray; Nguyen, Hung T

2015-09-01

We present a novel design of an intelligent robotic hospital bed, named Flexbed, with autonomous navigation ability. The robotic bed is developed for fast and safe transportation of critical neurosurgery patients without changing beds. Flexbed is more efficient and safe during the transportation process comparing to the conventional hospital beds. Flexbed is able to avoid en-route obstacles with an efficient easy-to-implement collision avoidance strategy when an obstacle is nearby and to move towards its destination at maximum speed when there is no threat of collision. We present extensive simulation results of navigation of Flexbed in the crowded hospital corridor environments with moving obstacles. Moreover, results of experiments with Flexbed in the real world scenarios are also presented and discussed.

Traffic Alert and Collision Avoidance System (TCAS): Cockpit Display of Traffic Information (CDTI) investigation. Phase 1: Feasibility study

NASA Technical Reports Server (NTRS)

Burgess, Malcolm; Davis, Dean; Hollister, Walter; Sorensen, John A.

1991-01-01

The possibility of the Threat Alert and Collision Avoidance System (TCAS) traffic sensor and display being used for meaningful Cockpit Display of Traffic Information (CDTI) applications has resulted in the Federal Aviation Administration initiating a project to establish the technical and operational requirements to realize this potential. Phase 1 of the project is presented here. Phase 1 was organized to define specific CDTI applications for the terminal area, to determine what has already been learned about CDTI technology relevant to these applications, and to define the engineering required to supply the remaining TCAS-CDTI technology for capacity benefit realization. The CDTI applications examined have been limited to those appropriate to the final approach and departure phases of flight.

35-GHz radar sensor for automotive collision avoidance

NASA Astrophysics Data System (ADS)

Zhang, Jun

1999-07-01

This paper describes the development of a radar sensor system used for automotive collision avoidance. Because the heavy truck may have great larger radar cross section than a motorcyclist has, the radar receiver may have a large dynamic range. And multi-targets at different speed may confuse the echo spectrum causing the ambiguity between range and speed of target. To get more information about target and background and to adapt to the large dynamic range and multi-targets, a frequency modulated and pseudo- random binary sequences phase modulated continuous wave radar system is described. The analysis of this double- modulation system is given. A high-speed signal processing and data processing component are used to process and combine the data and information from echo at different direction and at every moment.

CCA Test Objectives

NASA Technical Reports Server (NTRS)

2005-01-01

Three sources have been considered to provide information allowing the evaluation of the Collision Conflict Avoidance (CCA) functional requirements: existing data, simulation, and flight test. The existing data sources that have been evaluated have been found to be lacking in two areas: The actual data that was recorded and missing elements to the system architecture. Many previous tests addressing collision avoidance were conducted without a remote operator. As such, they are missing critical elements that are required to assess the CCA functional requirements. Tests such as ERAST were conducted with all of the UAS elements. However, ERAST tests were conducted as a demonstration and the data recorded was of end-to-end performance. Many contributing elements of the system were not individually recorded or were recorded at a data rate insufficient for the purposes of evaluating the CCA functional requirements.

Autonomous assembly with collision avoidance of a fleet of flexible spacecraft based on disturbance observer

NASA Astrophysics Data System (ADS)

Chen, Ti; Wen, Hao

2018-06-01

This paper presents a distributed control law with disturbance observer for the autonomous assembly of a fleet of flexible spacecraft to construct a large flexible space structure. The fleet of flexible spacecraft is driven to the pre-assembly configuration firstly, and then to the desired assembly configuration. A distributed assembly control law with disturbance observer is proposed by treating the flexible dynamics as disturbances acting on the rigid motion of the flexible spacecraft. Theoretical analysis shows that the control law can actuate the fleet to the desired configuration. Moreover, the collision avoidance between the members is also considered in the process from initial configuration to pre-assembly configuration. Finally, a numerical example is presented to verify the feasibility of proposed mission planning and the effectiveness of control law.

Energy behavior on side structure in event of ship collision subjected to external parameters.

PubMed

Prabowo, Aditya Rio; Bae, Dong Myung; Sohn, Jung Min; Cao, Bo

2016-11-01

The safety of ships in regards to collisions and groundings, as well as the navigational and structural aspects of ships, has been improved and developed up to this day by technical, administrative and nautical parties. The damage resulting from collisions could be reduced through several techniques such as designing appropriate hull structures, ensuring tightness of cargo tanks as well as observation and review on structural behaviors, whilst accounting for all involved parameters. The position during a collision can be influenced by the collisions' location and angle as these parts are included in the external dynamics of ship collisions. In this paper, the results of several collision analyses using the finite element method were used and reviewed regarding the effect of location and angle on energy characteristic. Firstly, the capabilities of the structure and its ability to resist destruction in a collision process were presented and comparisons were made to other collision cases. Three types of collisions were identified based on the relative location of contact points to each other. From the results, it was found that the estimation of internal energy by the damaged ships differed in range from 12%-24%. In the second stage, the results showed that a collision between 30 to 60 degrees produced higher level energy than a collision in the perpendicular position. Furthermore, it was concluded that striking and struck objects in collision contributed to energy and damage shape.

Safety and Convergence Analysis of Intersecting Aircraft Flows Under Decentralized Collision Avoidance

NASA Astrophysics Data System (ADS)

Dallal, Ahmed H.

Safety is an essential requirement for air traffic management and control systems. Aircraft are not allowed to get closer to each other than a specified safety distance, to avoid any conflicts and collisions between aircraft. Forecast analysis predicts a tremendous increase in the number of flights. Subsequently, automated tools are needed to help air traffic controllers resolve air born conflicts. In this dissertation, we consider the problem of conflict resolution of aircraft flows with the assumption that aircraft are flowing through a fixed specified control volume at a constant speed. In this regard, several centralized and decentralized resolution rules have been proposed for path planning and conflict avoidance. For the case of two intersecting flows, we introduce the concept of conflict touches, and a collaborative decentralized conflict resolution rule is then proposed and analyzed for two intersecting flows. The proposed rule is also able to resolved airborne conflicts that resulted from resolving another conflict via the domino effect. We study the safety conditions under the proposed conflict resolution and collision avoidance rule. Then, we use Lyapunov analysis to analytically prove the convergence of conflict resolution dynamics under the proposed rule. The analysis show that, under the proposed conflict resolution rule, the system of intersecting aircraft flows is guaranteed to converge to safe, conflict free, trajectories within a bounded time. Simulations are provided to verify the analytically derived conclusions and study the convergence of the conflict resolution dynamics at different encounter angles. Simulation results show that lateral deviations taken by aircraft in each flow, to resolve conflicts, are bounded, and aircraft converged to safe and conflict free trajectories, within a finite time.

Pilots' use of a traffic alert and collision-avoidance system (TCAS 2) in simulated air carrier operations. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Chappell, Sheryl L.; Billings, Charles E.; Scott, Barry C.; Tuttell, Robert J.; Olsen, M. Christine; Kozon, Thomas E.

1989-01-01

Pilots' use of and responses to a traffic alert and collision-avoidance system (TCAS 2) in simulated air carrier line operations are discribed in Volume 1. TCAS 2 monitors the positions of nearby aircraft by means of transponder interrogation, and it commands a climb or descent which conflicting aircraft are projected to reach an unsafe closest point-of-approach within 20 to 25 seconds. A different level of information about the location of other air traffic was presented to each of three groups of flight crews during their execution of eight simulated air carrier flights. A fourth group of pilots flew the same segments without TCAS 2 equipment. Traffic conflicts were generated at intervals during the flights; many of the conflict aircraft were visible to the flight crews. The TCAS equipment successfully ameliorated the seriousness of all conflicts; three of four non-TCAS crews had hazardous encounters. Response times to TCAS maneuver commands did not differ as a function of the amount of information provided, nor did response accuracy. Differences in flight experience did not appear to contribute to the small performance differences observed. Pilots used the displays of conflicting traffic to maneuver to avoid unseen traffic before maneuver advisories were issued by the TCAS equipment. The results indicate: (1) that pilots utilize TCAS effectively within the response times allocated by the TCAS logic, and (2) that TCAS 2 is an effective collision avoidance device. Volume 2 contains the appendices referenced in Volume 1, providing details of the experiment and the results, and the text of two reports written in support of the program.

Pilots' use of a traffic alert and collision-avoidance system (TCAS 2) in simulated air carrier operations. Volume 1: Methodology, summary and conclusions

NASA Technical Reports Server (NTRS)

Chappell, Sheryl L.; Billings, Charles E.; Scott, Barry C.; Tuttell, Robert J.; Olsen, M. Christine; Kozon, Thomas E.

1989-01-01

Pilots' use of and responses to a traffic alert and collision-avoidance system (TCAS 2) in simulated air carrier line operations are described in Volume 1. TCAS 2 monitors the positions of nearby aircraft by means of transponder interrogation, and it commands a climb or descent when conflicting aircraft are projected to reach an unsafe closest point-of-approach within 20 to 25 seconds. A different level of information about the location of other air traffic was presented to each of three groups of flight crews during their execution of eight simulated air carrier flights. A fourth group of pilots flew the same segments without TCAS 2 equipment. Traffic conflicts were generated at intervals during the flights; many of the conflict aircraft were visible to the flight crews. The TCAS equipment successfully ameliorated the seriousness of all conflicts; three of four non-TCAS crews had hazardous encounters. Response times to TCAS maneuver commands did not differ as a function of the amount of information provided, nor did response accuracy. Differences in flight experience did not appear to contribute to the small performance differences observed. Pilots used the displays of conflicting traffic to maneuver to avoid unseen traffic before maneuver advisories were issued by the TCAS equipment. The results indicate: (1) that pilots utilize TCAS effectively within the response times allocated by the TCAS logic, and (2) that TCAS 2 is an effective collision avoidance device. Volume II contains the appendices referenced in Volume I, providing details of the experiment and the results, and the text of two reports written in support of the program.

Evaluation of new collision-pair selection models in DSMC

NASA Astrophysics Data System (ADS)

Akhlaghi, Hassan; Roohi, Ehsan

2017-10-01

The current paper investigates new collision-pair selection procedures in a direct simulation Monte Carlo (DSMC) method. Collision partner selection based on the random procedure from nearest neighbor particles and deterministic selection of nearest neighbor particles have already been introduced as schemes that provide accurate results in a wide range of problems. In the current research, new collision-pair selections based on the time spacing and direction of the relative movement of particles are introduced and evaluated. Comparisons between the new and existing algorithms are made considering appropriate test cases including fluctuations in homogeneous gas, 2D equilibrium flow, and Fourier flow problem. Distribution functions for number of particles and collisions in cell, velocity components, and collisional parameters (collision separation, time spacing, relative velocity, and the angle between relative movements of particles) are investigated and compared with existing analytical relations for each model. The capability of each model in the prediction of the heat flux in the Fourier problem at different cell numbers, numbers of particles, and time steps is examined. For new and existing collision-pair selection schemes, the effect of an alternative formula for the number of collision-pair selections and avoiding repetitive collisions are investigated via the prediction of the Fourier heat flux. The simulation results demonstrate the advantages and weaknesses of each model in different test cases.

Collision sensitive niche profile of the worst affected bird-groups at wind turbine structures in the Federal State of Brandenburg, Germany.

PubMed

Bose, Anushika; Dürr, Tobias; Klenke, Reinhard A; Henle, Klaus

2018-02-28

Biodiversity-related impacts at wind energy facilities have increasingly become a cause of conservation concern, central issue being the collision of birds. Utilizing spatial information of their carcass detections at wind turbines (WTs), we quantified the detections in relation to the metric distances of the respective turbines to different land-use types. We used ecological niche factor analysis (ENFA) to identify combinations of land-use distances with respect to the spatial allocation of WTs that led to higher proportions of collisions among the worst affected bird-groups: Buntings, Crows, Larks, Pigeons and Raptors. We also assessed their respective similarities to the collision phenomenon by checking for overlaps amongst their distance combinations. Crows and Larks showed the narrowest "collision sensitive niche"; a part of ecological niche under higher risk of collisions with turbines, followed by that of Buntings and Pigeons. Raptors had the broadest niche showing significant overlaps with the collision sensitive niches of the other groups. This can probably be attributed to their larger home range combined with their hunting affinities to open landscapes. Identification of collision sensitive niches could be a powerful tool for landscape planning; helping avoid regions with higher risks of collisions for turbine allocations and thus protecting sensitive bird populations.

Validation of Essential Acoustic Parameters for Highly Urgent In-Vehicle Collision Warnings.

PubMed

Lewis, Bridget A; Eisert, Jesse L; Baldwin, Carryl L

2018-03-01

Objective The aim of this study was to validate the importance of key acoustic criteria for use as in-vehicle forward collision warning (FCW) systems. Background Despite recent advances in vehicle safety, automobile crashes remain one of the leading causes of death. As automation allows for more control of noncritical functions by the vehicle, the potential for disengagement and distraction from the driving task also increases. It is, therefore, as important as ever that in-vehicle safety-critical interfaces are intuitive and unambiguous, promoting effective collision avoidance responses upon first exposure even under divided-attention conditions. Method The current study used a driving simulator to assess the effectiveness of two warnings, one that met all essential acoustic parameters, one that met only some essential parameters, and a no-warning control in the context of a lead vehicle-following task in conjunction with a cognitive distractor task and collision event. Results Participants receiving an FCW comprising five essential acoustic components had improved collision avoidance responses relative to a no-warning condition and an FCW missing essential elements on their first exposure. Responses to a consistently good warning (GMU Prime) improved with subsequent exposures, whereas continued exposure to the less optimal FCW (GMU Sub-Prime) resulted in poorer performance even relative to receiving no warning at all. Conclusions This study provides support for previous warning design studies and for the validity of five key acoustic parameters essential for the design of effective in-vehicle FCWs. Application Results from this study have implications for the design of auditory FCWs and in-vehicle display design.

Recommended Screening Practices for Launch Collision Aviodance

NASA Technical Reports Server (NTRS)

Beaver, Brian A.; Hametz, Mark E.; Ollivierre, Jarmaine C.; Newman, Lauri K.; Hejduk, Matthew D.

2015-01-01

The objective of this document is to assess the value of launch collision avoidance (COLA) practices and provide recommendations regarding its implementation for NASA robotic missions. The scope of this effort is limited to launch COLA screens against catalog objects that are either spacecraft or debris. No modifications to manned safety COLA practices are considered in this effort. An assessment of the value of launch COLA can be broken down into two fundamental questions: 1) Does collision during launch represent a significant risk to either the payload being launched or the space environment? 2) Can launch collision mitigation be performed in a manner that provides meaningful risk reduction at an acceptable level of operational impact? While it has been possible to piece together partial answers to these questions for some time, the first attempt to comprehensively address them is documented in reference (a), Launch COLA Operations: an Examination of Data Products, Procedures, and Thresholds, Revision A. This report is the product of an extensive study that addressed fundamental technical questions surrounding launch collision avoidance analysis and practice. The results provided in reference (a) will be cited throughout this document as these two questions are addressed. The premise of this assessment is that in order to conclude that launch COLA is a value-added activity, the answer to both of these questions must be affirmative. A "no" answer to either of these questions points toward the conclusion that launch COLA provides little or no risk mitigation benefit. The remainder of this assessment will focus on addressing these two questions.

A collision dynamics model of a multi-level train

DOT National Transportation Integrated Search

2006-11-05

In train collisions, multi-level rail passenger vehicles can deform in modes that are different from the behavior of single level cars. The deformation in single level cars usually occurs at the front end during a collision. In one particular inciden...

Examination of the collision force method for analyzing the responses of simple containment/deflection structures to impact by one engine rotor blade fragment

NASA Technical Reports Server (NTRS)

Zirin, R. M.; Witmer, E. A.

1972-01-01

An approximate collision analysis, termed the collision-force method, was developed for studying impact-interaction of an engine rotor blade fragment with an initially circular containment ring. This collision analysis utilizes basic mass, material property, geometry, and pre-impact velocity information for the fragment, together with any one of three postulated patterns of blade deformation behavior: (1) the elastic straight blade model, (2) the elastic-plastic straight shortening blade model, and (3) the elastic-plastic curling blade model. The collision-induced forces are used to predict the resulting motions of both the blade fragment and the containment ring. Containment ring transient responses are predicted by a finite element computer code which accommodates the large deformation, elastic-plastic planar deformation behavior of simple structures such as beams and/or rings. The effects of varying the values of certain parameters in each blade-behavior model were studied. Comparisons of predictions with experimental data indicate that of the three postulated blade-behavior models, the elastic-plastic curling blade model appears to be the most plausible and satisfactory for predicting the impact-induced motions of a ductile engine rotor blade and a containment ring against which the blade impacts.

VLSI chips for vision-based vehicle guidance

NASA Astrophysics Data System (ADS)

Masaki, Ichiro

1994-02-01

Sensor-based vehicle guidance systems are gathering rapidly increasing interest because of their potential for increasing safety, convenience, environmental friendliness, and traffic efficiency. Examples of applications include intelligent cruise control, lane following, collision warning, and collision avoidance. This paper reviews the research trends in vision-based vehicle guidance with an emphasis on VLSI chip implementations of the vision systems. As an example of VLSI chips for vision-based vehicle guidance, a stereo vision system is described in detail.

Interpretable Categorization of Heterogeneous Time Series Data

NASA Technical Reports Server (NTRS)

Lee, Ritchie; Kochenderfer, Mykel J.; Mengshoel, Ole J.; Silbermann, Joshua

2017-01-01

We analyze data from simulated aircraft encounters to validate and inform the development of a prototype aircraft collision avoidance system. The high-dimensional and heterogeneous time series dataset is analyzed to discover properties of near mid-air collisions (NMACs) and categorize the NMAC encounters. Domain experts use these properties to better organize and understand NMAC occurrences. Existing solutions either are not capable of handling high-dimensional and heterogeneous time series datasets or do not provide explanations that are interpretable by a domain expert. The latter is critical to the acceptance and deployment of safety-critical systems. To address this gap, we propose grammar-based decision trees along with a learning algorithm. Our approach extends decision trees with a grammar framework for classifying heterogeneous time series data. A context-free grammar is used to derive decision expressions that are interpretable, application-specific, and support heterogeneous data types. In addition to classification, we show how grammar-based decision trees can also be used for categorization, which is a combination of clustering and generating interpretable explanations for each cluster. We apply grammar-based decision trees to a simulated aircraft encounter dataset and evaluate the performance of four variants of our learning algorithm. The best algorithm is used to analyze and categorize near mid-air collisions in the aircraft encounter dataset. We describe each discovered category in detail and discuss its relevance to aircraft collision avoidance.

33 CFR 110.205 - Chicago Harbor, Ill.

Code of Federal Regulations, 2014 CFR

2014-07-01

... movement of any boat, and shall move away immediately after the emergency ceases, or upon notification by... an established anchorage ground or in stress of weather or to avoid collision, is prohibited...

33 CFR 110.205 - Chicago Harbor, Ill.

Code of Federal Regulations, 2013 CFR

2013-07-01

... movement of any boat, and shall move away immediately after the emergency ceases, or upon notification by... an established anchorage ground or in stress of weather or to avoid collision, is prohibited...

33 CFR 110.205 - Chicago Harbor, Ill.

Code of Federal Regulations, 2011 CFR

2011-07-01

... movement of any boat, and shall move away immediately after the emergency ceases, or upon notification by... an established anchorage ground or in stress of weather or to avoid collision, is prohibited...

33 CFR 110.205 - Chicago Harbor, Ill.

Code of Federal Regulations, 2012 CFR

2012-07-01

... movement of any boat, and shall move away immediately after the emergency ceases, or upon notification by... an established anchorage ground or in stress of weather or to avoid collision, is prohibited...

ITS Architecture Development Program, Phase I; Summary Report

DOT National Transportation Integrated Search

1994-11-01

IN-VEHICLE EMISSIONS DIAGNOSIS, COMMERCIAL VEHICLES OPERATIONS OR CVO, ADVANCED VEHICLE CONTROL AND SAFETY SYSTEMS OR AVCSS, ADVANCED PUBLIC TRANSPORTATION SYSTEMS OR APTS, INCIDENT MANAGEMENT/INCIDENT DETECTION, COLLISION AVOIDANCE SYSTEM, AUTOMATED...

Sequence and Temperature Dependence of the End-to-End Collision Dynamics of Single-Stranded DNA

PubMed Central

Uzawa, Takanori; Isoshima, Takashi; Ito, Yoshihiro; Ishimori, Koichiro; Makarov, Dmitrii E.; Plaxco, Kevin W.

2013-01-01

Intramolecular collision dynamics play an essential role in biomolecular folding and function and, increasingly, in the performance of biomimetic technologies. To date, however, the quantitative studies of dynamics of single-stranded nucleic acids have been limited. Thus motivated, here we investigate the sequence composition, chain-length, viscosity, and temperature dependencies of the end-to-end collision dynamics of single-stranded DNAs. We find that both the absolute collision rate and the temperature dependencies of these dynamics are base-composition dependent, suggesting that base stacking interactions are a significant contributor. For example, whereas the end-to-end collision dynamics of poly-thymine exhibit simple, linear Arrhenius behavior, the behavior of longer poly-adenine constructs is more complicated. Specifically, 20- and 25-adenine constructs exhibit biphasic temperature dependencies, with their temperature dependences becoming effectively indistinguishable from that of poly-thymine above 335 K for 20-adenines and 328 K for 25-adenines. The differing Arrhenius behaviors of poly-thymine and poly-adenine and the chain-length dependence of the temperature at which poly-adenine crosses over to behave like poly-thymine can be explained by a barrier friction mechanism in which, at low temperatures, the energy barrier for the local rearrangement of poly-adenine becomes the dominant contributor to its end-to-end collision dynamics. PMID:23746521

Quantitative safety assessment of air traffic control systems through system control capacity

NASA Astrophysics Data System (ADS)

Guo, Jingjing

Quantitative Safety Assessments (QSA) are essential to safety benefit verification and regulations of developmental changes in safety critical systems like the Air Traffic Control (ATC) systems. Effectiveness of the assessments is particularly desirable today in the safe implementations of revolutionary ATC overhauls like NextGen and SESAR. QSA of ATC systems are however challenged by system complexity and lack of accident data. Extending from the idea "safety is a control problem" in the literature, this research proposes to assess system safety from the control perspective, through quantifying a system's "control capacity". A system's safety performance correlates to this "control capacity" in the control of "safety critical processes". To examine this idea in QSA of the ATC systems, a Control-capacity Based Safety Assessment Framework (CBSAF) is developed which includes two control capacity metrics and a procedural method. The two metrics are Probabilistic System Control-capacity (PSC) and Temporal System Control-capacity (TSC); each addresses an aspect of a system's control capacity. And the procedural method consists three general stages: I) identification of safety critical processes, II) development of system control models and III) evaluation of system control capacity. The CBSAF was tested in two case studies. The first one assesses an en-route collision avoidance scenario and compares three hypothetical configurations. The CBSAF was able to capture the uncoordinated behavior between two means of control, as was observed in a historic midair collision accident. The second case study compares CBSAF with an existing risk based QSA method in assessing the safety benefits of introducing a runway incursion alert system. Similar conclusions are reached between the two methods, while the CBSAF has the advantage of simplicity and provides a new control-based perspective and interpretation to the assessments. The case studies are intended to investigate the potential and demonstrate the utilities of CBSAF and are not intended for thorough studies of collision avoidance and runway incursions safety, which are extremely challenging problems. Further development and thorough validations are required to allow CBSAF to reach implementation phases, e.g. addressing the issues of limited scalability and subjectivity.

Chromosome biology: conflict management for replication and transcription.

PubMed

Dewar, James M; Walter, Johannes C

2013-03-04

A recent study has uncovered a new mechanism that attenuates DNA replication during periods of heightened gene expression to avoid collisions between replication and transcription. Copyright © 2013 Elsevier Ltd. All rights reserved.

Assessment of pilot workload with the introduction of an airborne threat-alert system

NASA Technical Reports Server (NTRS)

Battiste, Vernol; Bortolussi, Michael R.

1989-01-01

Simulated line operations were used to assess the value of the TCAS on the pilot's ability to avoid a collision and to determine the effects of various display configurations and information contents on the flight-crew performance and workload. The crew flew a Phase II Link/Boeing 727 simulator in a simulated ATC environment. Four levels of collision avoidance information were evaluated using the following TCAS display formats: no TCAS information, TCAS information with no traffic display information, TCAS information with threat-activated traffic display information, and TCAS information with a full-time traffic display of threat information. It was found that the use of a threat-activated TCAS display significantly reduced the first officers' workload was significantly reduced by the threat-activated TCAS display, as were the workloads of the captain and the second officer.

Visual guidance of forward flight in hummingbirds reveals control based on image features instead of pattern velocity.

PubMed

Dakin, Roslyn; Fellows, Tyee K; Altshuler, Douglas L

2016-08-02

Information about self-motion and obstacles in the environment is encoded by optic flow, the movement of images on the eye. Decades of research have revealed that flying insects control speed, altitude, and trajectory by a simple strategy of maintaining or balancing the translational velocity of images on the eyes, known as pattern velocity. It has been proposed that birds may use a similar algorithm but this hypothesis has not been tested directly. We examined the influence of pattern velocity on avian flight by manipulating the motion of patterns on the walls of a tunnel traversed by Anna's hummingbirds. Contrary to prediction, we found that lateral course control is not based on regulating nasal-to-temporal pattern velocity. Instead, birds closely monitored feature height in the vertical axis, and steered away from taller features even in the absence of nasal-to-temporal pattern velocity cues. For vertical course control, we observed that birds adjusted their flight altitude in response to upward motion of the horizontal plane, which simulates vertical descent. Collectively, our results suggest that birds avoid collisions using visual cues in the vertical axis. Specifically, we propose that birds monitor the vertical extent of features in the lateral visual field to assess distances to the side, and vertical pattern velocity to avoid collisions with the ground. These distinct strategies may derive from greater need to avoid collisions in birds, compared with small insects.

Distance estimation and collision prediction for on-line robotic motion planning

NASA Technical Reports Server (NTRS)

Kyriakopoulos, K. J.; Saridis, G. N.

1992-01-01

An efficient method for computing the minimum distance and predicting collisions between moving objects is presented. This problem is incorporated into the framework of an in-line motion-planning algorithm to satisfy collision avoidance between a robot and moving objects modeled as convex polyhedra. In the beginning, the deterministic problem where the information about the objects is assumed to be certain is examined. L(1) or L(infinity) norms are used to represent distance and the problem becomes a linear programming problem. The stochastic problem is formulated where the uncertainty is induced by sensing and the unknown dynamics of the moving obstacles. Two problems are considered: First, filtering of the distance between the robot and the moving object at the present time. Second, prediction of the minimum distance in the future in order to predict the collision time.

STCA, TCAS, Airproxes and Collision Risk

NASA Astrophysics Data System (ADS)

Brooker, Peter

2005-09-01

The focus here is on the performance of and interaction between the Traffic Alert and Collision Avoidance System (TCAS) and the controller's short-term conflict alert (STCA) system. The data source used is UK Airprox Board Reports of close encounters between aircraft, and the focus is on commercial air transport aircraft using UK controlled airspace with a radar service. Do the systems work well together? Are controllers surprised when they find out that a pilot has received a TCAS resolution advisory? What do TCAS and STCA events say about collision risk? Generally, the systems seem to work together well. On most occasions, controllers are not surprised by TCAS advisories: either they have detected the problem themselves or STCA has alerted them to it. The statistically expected rate of future mid-air collisions is estimated by extrapolation of Airprox closest encounter distances.

The Traffic-Alert and Collision Avoidance System (TCAS) in the glass cockpit

NASA Technical Reports Server (NTRS)

Chappell, Sheryl L.

1988-01-01

This volume contains the contributions of the participants in the NASA Ames Research Center workshop on the traffic-alert and collision avoidance system (TCAS) implementation for aircraft with cathode ray tube (CRT) or flat panel displays. To take advantage of the display capability of the advanced-technology aircraft, NASA sponsored this workshop with the intent of bringing together industry personnel, pilots, and researchers so that pertinent issues in the area could be identified. During the 2-day workshop participants addressed a number of issues including: What is the optimum format for TCAS advisories. Where and how should maneuver advisories be presented to the crew. Should the maneuver advisories be presented on the primary flight display. Is it appropriate to have the autopilot perform the avoidance maneuver. Where and how should traffic information be presented to the crew. Should traffic information be combined with weather and navigation information. How much traffic should be shown and what ranges should be used. Contained in the document are the concepts and suggestions produced by the workshop participants.

Fuzzy logic control system to provide autonomous collision avoidance for Mars rover vehicle

NASA Technical Reports Server (NTRS)

Murphy, Michael G.

1990-01-01

NASA is currently involved with planning unmanned missions to Mars to investigate the terrain and process soil samples in advance of a manned mission. A key issue involved in unmanned surface exploration on Mars is that of supporting autonomous maneuvering since radio communication involves lengthy delays. It is anticipated that specific target locations will be designated for sample gathering. In maneuvering autonomously from a starting position to a target position, the rover will need to avoid a variety of obstacles such as boulders or troughs that may block the shortest path to the target. The physical integrity of the rover needs to be maintained while minimizing the time and distance required to attain the target position. Fuzzy logic lends itself well to building reliable control systems that function in the presence of uncertainty or ambiguity. The following major issues are discussed: (1) the nature of fuzzy logic control systems and software tools to implement them; (2) collision avoidance in the presence of fuzzy parameters; and (3) techniques for adaptation in fuzzy logic control systems.

Avian collision risk at an offshore wind farm

PubMed Central

Desholm, Mark; Kahlert, Johnny

2005-01-01

We have been the first to investigate whether long-lived geese and ducks can detect and avoid a large offshore wind farm by tracking their diurnal migration patterns with radar. We found that the percentage of flocks entering the wind farm area decreased significantly (by a factor 4.5) from pre-construction to initial operation. At night, migrating flocks were more prone to enter the wind farm but counteracted the higher risk of collision in the dark by increasing their distance from individual turbines and flying in the corridors between turbines. Overall, less than 1% of the ducks and geese migrated close enough to the turbines to be at any risk of collision. PMID:17148191

Avian collision risk at an offshore wind farm.

PubMed

Desholm, Mark; Kahlert, Johnny

2005-09-22

We have been the first to investigate whether long-lived geese and ducks can detect and avoid a large offshore wind farm by tracking their diurnal migration patterns with radar. We found that the percentage of flocks entering the wind farm area decreased significantly (by a factor 4.5) from pre-construction to initial operation. At night, migrating flocks were more prone to enter the wind farm but counteracted the higher risk of collision in the dark by increasing their distance from individual turbines and flying in the corridors between turbines. Overall, less than 1% of the ducks and geese migrated close enough to the turbines to be at any risk of collision.

NASA's Orbital Debris Conjuction Assessment and Collision Avoidance Strategy

NASA Technical Reports Server (NTRS)

Gavin, Richard T.

2010-01-01

NASA has successfully used debris avoidance maneuvers to protect our spacecraft for more than 20 . years. This process which started out using parametric data and maneuver boxes has seen considerable evolution and now allows us to continue nominal operations for all but the most threatening objects. This has greatly reduced the interruptions to the critical mission objectives being pursued by NASA s Space Station, Space Shuttle, and robotic satellites.

Sense and avoid technology for unmanned aircraft systems

NASA Astrophysics Data System (ADS)

McCalmont, John; Utt, James; Deschenes, Michael; Taylor, Michael; Sanderson, Richard; Montgomery, Joel; Johnson, Randal S.; McDermott, David

2007-04-01

The Sensors Directorate of the Air Force Research Laboratory (AFRL), in conjunction with the Global Hawk Systems Group, the J-UCAS System Program Office and contractor Defense Research Associates, Inc. (DRA) is conducting an Advanced Technology Demonstration (ATD) of a sense-and-avoid capability with the potential to satisfy the Federal Aviation Administration's (FAA) requirement for Unmanned Aircraft Systems (UAS) to provide "an equivalent level of safety, comparable to see-and-avoid requirements for manned aircraft". This FAA requirement must be satisfied for UAS operations within the national airspace. The Sense-and-Avoid, Phase I (Man-in-the-Loop) and Phase II (Autonomous Maneuver) ATD demonstrated an on-board, wide field of regard, multi-sensor visible imaging system operating in real time and capable of passively detecting approaching aircraft, declaring potential collision threats in a timely manner and alerting the human pilot located in the remote ground control station or autonomously maneuvered the aircraft. Intruder declaration data was collected during the SAA I & II Advanced Technology Demonstration flights conducted during December 2006. A total of 27 collision scenario flights were conducted and analyzed. The average detection range was 6.3 NM and the mean declaration range was 4.3 NM. The number of false alarms per engagement has been reduced to approximately 3 per engagement.

A Reliable Data Transmission Model for IEEE 802.15.4e Enabled Wireless Sensor Network under WiFi Interference.

PubMed

Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

2017-06-07

The IEEE 802.15.4e standard proposes Medium Access Control (MAC) to support collision-free wireless channel access mechanisms for industrial, commercial and healthcare applications. However, unnecessary wastage of energy and bandwidth consumption occur due to inefficient backoff management and collisions. In this paper, a new channel access mechanism is designed for the buffer constraint sensor devices to reduce the packet drop rate, energy consumption and collisions. In order to avoid collision due to the hidden terminal problem, a new frame structure is designed for the data transmission. A new superframe structure is proposed to mitigate the problems due to WiFi and ZigBee interference. A modified superframe structure with a new retransmission opportunity for failure devices is proposed to reduce the collisions and retransmission delay with high reliability. Performance evaluation and validation of our scheme indicate that the packet drop rate, throughput, reliability, energy consumption and average delay of the nodes can be improved significantly.

System engineering analysis of derelict collision prevention options

NASA Astrophysics Data System (ADS)

McKnight, Darren S.; Di Pentino, Frank; Kaczmarek, Adam; Dingman, Patrick

2013-08-01

Sensitivities to the future growth of orbital debris and the resulting hazard to operational satellites due to collisional breakups of large derelict objects are being studied extensively. However, little work has been done to quantify the technical and operational tradeoffs between options for minimizing future derelict fragmentations that act as the primary source for future debris hazard growth. The two general categories of debris mitigation examined for prevention of collisions involving large derelict objects (rocket bodies and payloads) are active debris removal (ADR) and just-in-time collision avoidance (JCA). Timing, cost, and effectiveness are compared for ADR and JCA solutions highlighting the required enhancements in uncooperative element set accuracy, rapid ballistic launch, despin/grappling systems, removal technologies, and remote impulsive devices. The primary metrics are (1) the number of derelict objects moved/removed per the number of catastrophic collisions prevented and (2) cost per collision event prevented. A response strategy that contains five different activities, including selective JCA and ADR, is proposed as the best approach going forward.

Three-dimensional derailment analysis of a crashed city tram

NASA Astrophysics Data System (ADS)

Zhou, Hechao; Wang, Wenbin; Hecht, Markus

2013-08-01

City tram collisions are simulated using multi-body dynamics. The aim of this paper is to investigate the collision-induced derailment. Simulation results demonstrate that the corner obstacle collision scenario defined in EN 15227 is mainly focused on the energy absorption process. Due to the large impact angle (45°), it is unlikely for a city tram to comply with this scenario without derailment. In order to avoid derailment, the maximum impact angle between city tram and oblique obstacle should be reduced to 25°. Moreover, some influence factors are analysed, such as mass of loaded passengers, friction coefficient, impact angle, etc. Derailment phenomenon is shown to be significantly dependent on these parameters. Two measures are proposed to prevent the collided city tram from derailment. One is using secondary lateral dampers to absorb collision energy. Another is increasing the lateral stiffness of secondary springs as well as the lateral clearance, so that more collision energy can be stored in the suspension. With these measures, the safety against derailment can be improved.

A Reliable Data Transmission Model for IEEE 802.15.4e Enabled Wireless Sensor Network under WiFi Interference

PubMed Central

Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

2017-01-01

The IEEE 802.15.4e standard proposes Medium Access Control (MAC) to support collision-free wireless channel access mechanisms for industrial, commercial and healthcare applications. However, unnecessary wastage of energy and bandwidth consumption occur due to inefficient backoff management and collisions. In this paper, a new channel access mechanism is designed for the buffer constraint sensor devices to reduce the packet drop rate, energy consumption and collisions. In order to avoid collision due to the hidden terminal problem, a new frame structure is designed for the data transmission. A new superframe structure is proposed to mitigate the problems due to WiFi and ZigBee interference. A modified superframe structure with a new retransmission opportunity for failure devices is proposed to reduce the collisions and retransmission delay with high reliability. Performance evaluation and validation of our scheme indicate that the packet drop rate, throughput, reliability, energy consumption and average delay of the nodes can be improved significantly. PMID:28590434

Millimeter wave radar for automobile crash avoidance systems

NASA Astrophysics Data System (ADS)

Huguenin, G. Richard

1994-08-01

Low cost, millimeter wave, forward looking radar sensors for applications in Autonomous Collision Warning and Autonomous Intelligent Cruise Control systems will be described. These safety related systems promise the largest payoff in preventing highway crashes.

TS0-C142, Lithium Batteries (proposed)

DOT National Transportation Integrated Search

2000-01-01

Success in developing IVHS collision avoidance systems that are both commercially attractive and effective will depend in large part on how well product designers understand and accommodate human factors considerations in their designs. Help from the...

Anticollision lights for the supersonic transport.

DOT National Transportation Integrated Search

1970-05-01

For visual detection at night, the aircraft must display conspicuous light signals to indicate its presence and course at sufficient distance and time remaining for the pilot to avoid a collision. Considerations about the usefulness of anticollision ...

Experimental BCAS Performance Results

DOT National Transportation Integrated Search

1978-07-01

The results of the (Litchford) Beacon-based Collision Avoidance System concept feasibility evaluation are reported. Included are a description of the concept, analysis and flight test results. The system concept is based on the range and bearing meas...

Permeability of roads to movement of scrubland lizards and small mammals.

PubMed

Brehme, Cheryl S; Tracey, Jeff A; McClenaghan, Leroy R; Fisher, Robert N

2013-08-01

A primary objective of road ecology is to understand and predict how roads affect connectivity of wildlife populations. Road avoidance behavior can fragment populations, whereas lack of road avoidance can result in high mortality due to wildlife-vehicle collisions. Many small animal species focus their activities to particular microhabitats within their larger habitat. We sought to assess how different types of roads affect the movement of small vertebrates and to explore whether responses to roads may be predictable on the basis of animal life history or microhabitat preferences preferences. We tracked the movements of fluorescently marked animals at 24 sites distributed among 3 road types: low-use dirt, low-use secondary paved, and rural 2-lane highway. Most data we collected were on the San Diego pocket mouse (Chaetodipus fallax), cactus mouse (Peromyscus eremicus), western fence lizard (Sceloporus occidentalis), orange-throated whiptail (Aspidoscelis hyperythra), Dulzura kangaroo rat (Dipodomys simulans) (dirt, secondary paved), and deer mouse (Peromyscus maniculatus) (highway only). San Diego pocket mice and cactus mice moved onto dirt roads but not onto a low-use paved road of similar width or onto the highway, indicating they avoid paved road substrate. Both lizard species moved onto the dirt and secondary paved roads but avoided the rural 2-lane rural highway, indicating they may avoid noise, vibration, or visual disturbance from a steady flow of traffic. Kangaroo rats did not avoid the dirt or secondary paved roads. Overall, dirt and secondary roads were more permeable to species that prefer to forage or bask in open areas of their habitat, rather than under the cover of rocks or shrubs. However, all study species avoided the rural 2-lane highway. Our results suggest that microhabitat use preferences and road substrate help predict species responses to low-use roads, but roads with heavy traffic may deter movement of a much wider range of small animal species. © 2013 Society for Conservation Biology.

Unifying Time to Contact Estimation and Collision Avoidance across Species

PubMed Central

Keil, Matthias S.; López-Moliner, Joan

2012-01-01

The -function and the -function are phenomenological models that are widely used in the context of timing interceptive actions and collision avoidance, respectively. Both models were previously considered to be unrelated to each other: is a decreasing function that provides an estimation of time-to-contact (ttc) in the early phase of an object approach; in contrast, has a maximum before ttc. Furthermore, it is not clear how both functions could be implemented at the neuronal level in a biophysically plausible fashion. Here we propose a new framework – the corrected modified Tau function – capable of predicting both -type (“”) and -type (“”) responses. The outstanding property of our new framework is its resilience to noise. We show that can be derived from a firing rate equation, and, as , serves to describe the response curves of collision sensitive neurons. Furthermore, we show that predicts the psychophysical performance of subjects determining ttc. Our new framework is thus validated successfully against published and novel experimental data. Within the framework, links between -type and -type neurons are established. Therefore, it could possibly serve as a model for explaining the co-occurrence of such neurons in the brain. PMID:22915999

Advanced driver assistance systems: Using multimodal redundant warnings to enhance road safety.

PubMed

Biondi, Francesco; Strayer, David L; Rossi, Riccardo; Gastaldi, Massimiliano; Mulatti, Claudio

2017-01-01

This study investigated whether multimodal redundant warnings presented by advanced assistance systems reduce brake response times. Warnings presented by assistance systems are designed to assist drivers by informing them that evasive driving maneuvers are needed in order to avoid a potential accident. If these warnings are poorly designed, they may distract drivers, slow their responses, and reduce road safety. In two experiments, participants drove a simulated vehicle equipped with a forward collision avoidance system. Auditory, vibrotactile, and multimodal warnings were presented when the time to collision was shorter than five seconds. The effects of these warnings were investigated with participants performing a concurrent cell phone conversation (Exp. 1) or driving in high-density traffic (Exp. 2). Braking times and subjective workload were measured. Multimodal redundant warnings elicited faster braking reaction times. These warnings were found to be effective even when talking on a cell phone (Exp. 1) or driving in dense traffic (Exp. 2). Multimodal warnings produced higher ratings of urgency, but ratings of frustration did not increase compared to other warnings. Findings obtained in these two experiments are important given that faster braking responses may reduce the potential for a collision. Copyright © 2016 Elsevier Ltd. All rights reserved.

Interactive-rate Motion Planning for Concentric Tube Robots

PubMed Central

Torres, Luis G.; Baykal, Cenk; Alterovitz, Ron

2014-01-01

Concentric tube robots may enable new, safer minimally invasive surgical procedures by moving along curved paths to reach difficult-to-reach sites in a patient’s anatomy. Operating these devices is challenging due to their complex, unintuitive kinematics and the need to avoid sensitive structures in the anatomy. In this paper, we present a motion planning method that computes collision-free motion plans for concentric tube robots at interactive rates. Our method’s high speed enables a user to continuously and freely move the robot’s tip while the motion planner ensures that the robot’s shaft does not collide with any anatomical obstacles. Our approach uses a highly accurate mechanical model of tube interactions, which is important since small movements of the tip position may require large changes in the shape of the device’s shaft. Our motion planner achieves its high speed and accuracy by combining offline precomputation of a collision-free roadmap with online position control. We demonstrate our interactive planner in a simulated neurosurgical scenario where a user guides the robot’s tip through the environment while the robot automatically avoids collisions with the anatomical obstacles. PMID:25436176

Behavioral and experiential avoidance in patients with hoarding disorder.

PubMed

Ayers, Catherine R; Castriotta, Natalie; Dozier, Mary E; Espejo, Emmanuel P; Porter, Ben

2014-09-01

This study examined the relationship between experiential and behavioral avoidance and hoarding symptom severity, controlling for anxiety and depression symptoms, in 66 adult individuals (M age = 61.41; SD = 9.03) with HD. Hierarchical regression was used to test the associations between hoarding severity, as defined by the Savings Inventory-Revised (SI-R) total and its three subscales, and avoidance, as defined by the Acceptance and Action Questionnaire II (AAQ-II) and two scales from the Brief COPE (Self-Distraction and Behavioral Disengagement) when controlling for anxiety and depression symptoms. Experiential avoidance (AAQ-II) and behavioral avoidance (Brief COPE subscales Self-Distraction and Behavioral Disengagement) uniquely accounted for aspects of hoarding severity (SI-R) in regression models. Behavioral avoidance contributed significant additional variance to the SI-R Clutter subscale, whereas experiential avoidance was uniquely predictive of additional variance in the SI-R Difficulty Discarding and the SI-R Acquisition subscales. Future research should examine the effect of experiential avoidance on hoarding behaviors experimentally. Given that the AAQ-II and Self-Distraction and Behavioral Disengagement subscales were not correlated, these findings suggest that experiential and behavioral avoidance are two distinct processes contributing to the severity of specific HD. Results support the utility of avoidance in the cognitive-behavioral model for HD. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of Particle Size and Impact Velocity on Collision Behaviors Between Nano-Scale TiN Particles: MD Simulation.

PubMed

Yao, Hai-Long; Hu, Xiao-Zhen; Yang, Guan-Jun

2018-06-01

Inter-particle bonding formation which determines qualities of nano-scale ceramic coatings is influenced by particle collision behaviors during high velocity collision processes. In this study, collision behaviors between nano-scale TiN particles with different diameters were illuminated by using Molecular Dynamics simulation through controlling impact velocities. Results show that nano-scale TiN particles exhibit three states depending on particle sizes and impact velocities, i.e., bonding, bonding with localized fracturing, and rebounding. These TiN particles states are summarized into a parameter selection map providing an overview of the conditions in terms of particle sizes and velocities. Microstructure results show that localized atoms displacement and partial fracture around the impact region are main reasons for bonding formation of nano-scale ceramic particles, which shows differences from conventional particles refining and amorphization. A relationship between the adhesion energy and the rebound energy is established to understand bonding formation mechanism for nano-scale TiN particle collision. Results show that the energy relationship is depended on the particle sizes and impact velocities, and nano-scale ceramic particles can be bonded together as the adhesion energy being higher than the rebound energy.

Treatment of avoidance behavior as an adjunct to exposure therapy: Insights from modern learning theory.

PubMed

Treanor, Michael; Barry, Tom J

2017-09-01

Pathological avoidance of benign stimuli is a hallmark of anxiety and related disorders, and exposure-based treatments have often encouraged the removal of avoidance, or safety behaviors, due to their negative effects on extinction learning. Unfortunately, empirical evidence suggests that avoidance behaviors can persist following treatment, and the mere availability of avoidance behavior can be sufficient to renew fear following successful extinction learning. The present paper critically examines the function of avoidance behavior through the lens of modern learning theory, and speculates on novel behavioral and pharmacological strategies for targeting avoidance as an adjunct to current evidence-based treatments. Copyright © 2017. Published by Elsevier Ltd.

Tracking colliding cells in vivo microscopy.

PubMed

Nguyen, Nhat H; Keller, Steven; Norris, Eric; Huynh, Toan T; Clemens, Mark G; Shin, Min C

2011-08-01

Leukocyte motion represents an important component in the innate immune response to infection. Intravital microscopy is a powerful tool as it enables in vivo imaging of leukocyte motion. Under inflammatory conditions, leukocytes may exhibit various motion behaviors, such as flowing, rolling, and adhering. With many leukocytes moving at a wide range of speeds, collisions occur. These collisions result in abrupt changes in the motion and appearance of leukocytes. Manual analysis is tedious, error prone,time consuming, and could introduce technician-related bias. Automatic tracking is also challenging due to the noise inherent in in vivo images and abrupt changes in motion and appearance due to collision. This paper presents a method to automatically track multiple cells undergoing collisions by modeling the appearance and motion for each collision state and testing collision hypotheses of possible transitions between states. The tracking results are demonstrated using in vivo intravital microscopy image sequences.We demonstrate that 1)71% of colliding cells are correctly tracked; (2) the improvement of the proposed method is enhanced when the duration of collision increases; and (3) given good detection results, the proposed method can correctly track 88% of colliding cells. The method minimizes the tracking failures under collisions and, therefore, allows more robust analysis in the study of leukocyte behaviors responding to inflammatory conditions.

Implementation of an open-scenario, long-term space debris simulation approach

NASA Astrophysics Data System (ADS)

Stupl, J.; Nelson, B.; Faber, N.; Perez, A.; Carlino, R.; Yang, F.; Henze, C.; Karacalioglu, A.; O'Toole, C.; Swenson, J.

This paper provides a status update on the implementation of a flexible, long-term space debris simulation approach. The motivation is to build a tool that can assess the long-term impact of various options for debris-remediation, including the LightForce space debris collision avoidance scheme. State-of-the-art simulation approaches that assess the long-term development of the debris environment use either completely statistical approaches, or they rely on large time steps in the order of several (5-15) days if they simulate the positions of single objects over time. They cannot be easily adapted to investigate the impact of specific collision avoidance schemes or de-orbit schemes, because the efficiency of a collision avoidance maneuver can depend on various input parameters, including ground station positions, space object parameters and orbital parameters of the conjunctions and take place in much smaller timeframes than 5-15 days. For example, LightForce only changes the orbit of a certain object (aiming to reduce the probability of collision), but it does not remove entire objects or groups of objects. In the same sense, it is also not straightforward to compare specific de-orbit methods in regard to potential collision risks during a de-orbit maneuver. To gain flexibility in assessing interactions with objects, we implement a simulation that includes every tracked space object in LEO, propagates all objects with high precision, and advances with variable-sized time-steps as small as one second. It allows the assessment of the (potential) impact of changes to any object. The final goal is to employ a Monte Carlo approach to assess the debris evolution during the simulation time-frame of 100 years and to compare a baseline scenario to debris remediation scenarios or other scenarios of interest. To populate the initial simulation, we use the entire space-track object catalog in LEO. We then use a high precision propagator to propagate all objects over the entire simulation duration. If collisions are detected, the appropriate number of debris objects are created and inserted into the simulation framework. Depending on the scenario, further objects, e.g. due to new launches, can be added. At the end of the simulation, the total number of objects above a cut-off size and the number of detected collisions provide benchmark parameters for the comparison between scenarios. The simulation approach is computationally intensive as it involves ten thousands of objects; hence we use a highly parallel approach employing up to a thousand cores on the NASA Pleiades supercomputer for a single run. This paper describes our simulation approach, the status of its implementation, the approach in developing scenarios and examples of first test runs.

Implementation of an Open-Scenario, Long-Term Space Debris Simulation Approach

NASA Technical Reports Server (NTRS)

Nelson, Bron; Yang Yang, Fan; Carlino, Roberto; Dono Perez, Andres; Faber, Nicolas; Henze, Chris; Karacalioglu, Arif Goktug; O'Toole, Conor; Swenson, Jason; Stupl, Jan

2015-01-01

This paper provides a status update on the implementation of a flexible, long-term space debris simulation approach. The motivation is to build a tool that can assess the long-term impact of various options for debris-remediation, including the LightForce space debris collision avoidance concept that diverts objects using photon pressure [9]. State-of-the-art simulation approaches that assess the long-term development of the debris environment use either completely statistical approaches, or they rely on large time steps on the order of several days if they simulate the positions of single objects over time. They cannot be easily adapted to investigate the impact of specific collision avoidance schemes or de-orbit schemes, because the efficiency of a collision avoidance maneuver can depend on various input parameters, including ground station positions and orbital and physical parameters of the objects involved in close encounters (conjunctions). Furthermore, maneuvers take place on timescales much smaller than days. For example, LightForce only changes the orbit of a certain object (aiming to reduce the probability of collision), but it does not remove entire objects or groups of objects. In the same sense, it is also not straightforward to compare specific de-orbit methods in regard to potential collision risks during a de-orbit maneuver. To gain flexibility in assessing interactions with objects, we implement a simulation that includes every tracked space object in Low Earth Orbit (LEO) and propagates all objects with high precision and variable time-steps as small as one second. It allows the assessment of the (potential) impact of physical or orbital changes to any object. The final goal is to employ a Monte Carlo approach to assess the debris evolution during the simulation time-frame of 100 years and to compare a baseline scenario to debris remediation scenarios or other scenarios of interest. To populate the initial simulation, we use the entire space-track object catalog in LEO. We then use a high precision propagator to propagate all objects over the entire simulation duration. If collisions are detected, the appropriate number of debris objects are created and inserted into the simulation framework. Depending on the scenario, further objects, e.g. due to new launches, can be added. At the end of the simulation, the total number of objects above a cut-off size and the number of detected collisions provide benchmark parameters for the comparison between scenarios. The simulation approach is computationally intensive as it involves tens of thousands of objects; hence we use a highly parallel approach employing up to a thousand cores on the NASA Pleiades supercomputer for a single run. This paper describes our simulation approach, the status of its implementation, the approach to developing scenarios and examples of first test runs.

Morgantown People Mover Collision Avoidance System Design Summary

DOT National Transportation Integrated Search

1980-09-01

The Morgantown People Mover (MPM) is an automated two-mode (schedule and demand) transit system that consists of a fleet of electrically powered, rubber-tired, passenger-carrying vehicles operating on a dedicated guideway under computer control. The ...

Results of DATAS Investigation of ATCRBS Environment at Los Angeles International Airport

DOT National Transportation Integrated Search

1993-04-01

Federal Aviation Administration (FAA) Technical Center Data Link project : personnel designed, developed, and deployed a system to record Traffic Alert : and Collision Avoidance System (TCAS) activity. Through coordinated efforts with : TCAS project ...

Beacon Collision Avoidance System (BCAS) Airborne Antenna Diversity Study

DOT National Transportation Integrated Search

1978-04-01

The potential need for antenna diversity on the intruding aircraft was examined. The BCAS system was used for determining airborne antenna diversity requirements for general aviation aircraft approaching a BCAS equipped aircraft from various angles. ...

Asset Analysis and Operational Concepts for Separation Assurance Flight Testing at Dryden Flight Research Center

NASA Technical Reports Server (NTRS)

Costa, Guillermo J.; Arteaga, Ricardo A.

2011-01-01

A preliminary survey of existing separation assurance and collision avoidance advancements, technologies, and efforts has been conducted in order to develop a concept of operations for flight testing autonomous separation assurance at Dryden Flight Research Center. This effort was part of the Unmanned Aerial Systems in the National Airspace System project. The survey focused primarily on separation assurance projects validated through flight testing (including lessons learned), however current forays into the field were also examined. Comparisons between current Dryden flight and range assets were conducted using House of Quality matrices in order to allow project management to make determinations regarding asset utilization for future flight tests. This was conducted in order to establish a body of knowledge of the current collision avoidance landscape, and thus focus Dryden s efforts more effectively towards the providing of assets and test ranges for future flight testing within this research field.

Analysis of the minimum swerving distance for the development of a motorcycle autonomous braking system.

PubMed

Giovannini, Federico; Savino, Giovanni; Pierini, Marco; Baldanzini, Niccolò

2013-10-01

In the recent years the autonomous emergency brake (AEB) was introduced in the automotive field to mitigate the injury severity in case of unavoidable collisions. A crucial element for the activation of the AEB is to establish when the obstacle is no longer avoidable by lateral evasive maneuvers (swerving). In the present paper a model to compute the minimum swerving distance needed by a powered two-wheeler (PTW) to avoid the collision against a fixed obstacle, named last-second swerving model (Lsw), is proposed. The effectiveness of the model was investigated by an experimental campaign involving 12 volunteers riding a scooter equipped with a prototype autonomous emergency braking, named motorcycle autonomous emergency braking system (MAEB). The tests showed the performance of the model in evasive trajectory computation for different riding styles and fixed obstacles. Copyright © 2013 Elsevier Ltd. All rights reserved.

Head-Up Auditory Displays for Traffic Collision Avoidance System Advisories: A Preliminary Investigation

NASA Technical Reports Server (NTRS)

Begault, Durand R.

1993-01-01

The advantage of a head-up auditory display was evaluated in a preliminary experiment designed to measure and compare the acquisition time for capturing visual targets under two auditory conditions: standard one-earpiece presentation and two-earpiece three-dimensional (3D) audio presentation. Twelve commercial airline crews were tested under full mission simulation conditions at the NASA-Ames Man-Vehicle Systems Research Facility advanced concepts flight simulator. Scenario software generated visual targets corresponding to aircraft that would activate a traffic collision avoidance system (TCAS) aural advisory; the spatial auditory position was linked to the visual position with 3D audio presentation. Results showed that crew members using a 3D auditory display acquired targets approximately 2.2 s faster than did crew members who used one-earpiece head- sets, but there was no significant difference in the number of targets acquired.

Study of flight data recorder, underwater locator beacon, data logger and flarm collision avoidance system

NASA Astrophysics Data System (ADS)

Timi, Purnota Hannan; Shermin, Saima; Rahman, Asifur

2017-06-01

Flight data recorder is one of the most important sources of flight data in event of aviation disaster which records a wide range of flight parameters including altitude, airspeed, heading etc. and also helps monitoring and analyzing aircraft performance. Cockpit voice recorder records radio microphone transmissions and sounds in the cockpit. These devices help to find out and understand the root causes of aircraft crashes and help building better aircraft systems and technical solutions to prevent similar type of crashes in future, which lead to improvement in safety of aircrafts and passengers. There are other devices also which enhance the aircraft safety and assists in emergency or catastrophic situations. This paper discusses the concept of Flight Data Recorder (FDR), Cockpit Voice Recorder (CVR), Underwater Locator Beacon (ULB), Data logger and flarm-collision avoidance system for aircraft and their applications in aviation.

Integrated Display and Simulation for Automatic Dependent Surveillance-Broadcast and Traffic Collision Avoidance System Data Fusion.

PubMed

Wang, Yanran; Xiao, Gang; Dai, Zhouyun

2017-11-13

Automatic Dependent Surveillance-Broadcast (ADS-B) is the direction of airspace surveillance development. Research analyzing the benefits of Traffic Collision Avoidance System (TCAS) and ADS-B data fusion is almost absent. The paper proposes an ADS-B minimum system from ADS-B In and ADS-B Out. In ADS-B In, a fusion model with a variable sampling Variational Bayesian-Interacting Multiple Model (VSVB-IMM) algorithm is proposed for integrated display and an airspace traffic situation display is developed by using ADS-B information. ADS-B Out includes ADS-B Out transmission based on a simulator platform and an Unmanned Aerial Vehicle (UAV) platform. This paper describes the overall implementation of ADS-B minimum system, including theoretical model design, experimental simulation verification, engineering implementation, results analysis, etc. Simulation and implementation results show that the fused system has better performance than each independent subsystem and it can work well in engineering applications.

Mixed-mode VLSI optic flow sensors for in-flight control of a micro air vehicle

NASA Astrophysics Data System (ADS)

Barrows, Geoffrey L.; Neely, C.

2000-11-01

NRL is developing compact optic flow sensors for use in a variety of small-scale navigation and collision avoidance tasks. These sensors are being developed for use in micro air vehicles (MAVs), which are autonomous aircraft whose maximum dimension is on the order of 15 cm. To achieve desired weight specifications of 1 - 2 grams, mixed-signal VLSI circuitry is being used to develop compact focal plane sensors that directly compute optic flow. As an interim proof of principle, we have constructed a sensor comprising a focal plane sensor head with on-chip processing and a back-end PIC microcontroller. This interim sensors weighs approximately 25 grams and is able to measure optic flow with real-world and low-contrast textures. Variations of this sensor have been used to control the flight of a glider in real-time to avoid collisions with walls.

Advanced mechanisms for robotics

NASA Technical Reports Server (NTRS)

Vranish, John M.

1992-01-01

An overview of applied research and development at NASA-Goddard (GSFC) on mechanisms and the collision avoidance skin for robots is presented. First the work on robot end effectors is outlined, followed by a brief discussion on robot-friendly payload latching mechanisms and compliant joints. This, in turn, is followed by the collision avoidance/management skin and the GSFC research on magnetostrictive direct drive motors. Finally, a new project, the artificial muscle, is introduced. Each of the devices is described in sufficient detail to permit a basic understanding of its purpose, fundamental principles of operation, and capabilities. In addition, the development status of each is reported along with descriptions of breadboards and prototypes and their test results. In each case, the implications of the research for commercialization is discussed. The chronology of the presentation will give a clear idea of both the evolution of the R&D in recent years and its likely direction in the future.

Improved computer simulation of the TCAS 3 circular array mounted on an aircraft

NASA Astrophysics Data System (ADS)

Rojas, R. G.; Chen, Y. C.; Burnside, Walter D.

1989-03-01

The Traffic advisory and Collision Avoidance System (TCAS) is being developed by the Federal Aviation Administration (FAA) to assist aircraft pilots in mid-air collision avoidance. This report concentrates on the computer simulation of the enchanced TCAS 2 systems mounted on a Boeing 727. First, the moment method is used to obtain an accurate model for the enhanced TCAS 2 antenna array. Then, the OSU Aircraft Code is used to generate theoretical radiation patterns of this model mounted on a simulated Boeing 727 model. Scattering error curves obtained from these patterns can be used to evaluate the performance of this system in determining the angular position of another aircraft with respect to the TCAS-equipped aircraft. Finally, the tracking of another aircraft is simulated when the TCAS-equipped aircraft follows a prescribed escape curve. In short, the computer models developed in this report have generality, completeness and yield reasonable results.

A 5 meter range non-planar CMUT array for Automotive Collision Avoidance

NASA Astrophysics Data System (ADS)

Hernandez Aguirre, Jonathan

A discretized hyperbolic paraboloid geometry capacitive micromachined ultrasonic transducer (CMUT) array has been designed and fabricated for automotive collision avoidance. The array is designed to operate at 40 kHz, beamwidth of 40° with a maximum sidelobe intensity of -10dB. An SOI based fabrication technology has been used for the 5x5 array with 5 sensing surfaces along each x and y axis and 7 elevation levels. An assembly and packaging technique has been developed to realize the non-planar geometry in a PGA-68 package. A highly accurate mathematical method has been presented for analytical characterization of capacitive micromachined ultrasonic transducers (CMUTs) built with square diaphragms. The method uses a new two-dimensional polynomial function to more accurately predict the deflection curve of a multilayer square diaphragm subject to both mechanical and electrostatic pressure and a new capacitance model that takes into account the contribution of the fringing field capacitances.

NASA UAS Integration into the NAS Project: Human Systems Integration

NASA Technical Reports Server (NTRS)

Shively, Jay

2016-01-01

This presentation provides an overview of the work the Human Systems Integration (HSI) sub-project has done on detect and avoid (DAA) displays while working on the UAS (Unmanned Aircraft System) Integration into the NAS project. The most recent simulation on DAA interoperability with Traffic Collision Avoidance System (TCAS) is discussed in the most detail. The relationship of the work to the larger UAS community and next steps are also detailed.

Statistical Orbit Determination using the Particle Filter for Incorporating Non-Gaussian Uncertainties

NASA Technical Reports Server (NTRS)

Mashiku, Alinda; Garrison, James L.; Carpenter, J. Russell

2012-01-01

The tracking of space objects requires frequent and accurate monitoring for collision avoidance. As even collision events with very low probability are important, accurate prediction of collisions require the representation of the full probability density function (PDF) of the random orbit state. Through representing the full PDF of the orbit state for orbit maintenance and collision avoidance, we can take advantage of the statistical information present in the heavy tailed distributions, more accurately representing the orbit states with low probability. The classical methods of orbit determination (i.e. Kalman Filter and its derivatives) provide state estimates based on only the second moments of the state and measurement errors that are captured by assuming a Gaussian distribution. Although the measurement errors can be accurately assumed to have a Gaussian distribution, errors with a non-Gaussian distribution could arise during propagation between observations. Moreover, unmodeled dynamics in the orbit model could introduce non-Gaussian errors into the process noise. A Particle Filter (PF) is proposed as a nonlinear filtering technique that is capable of propagating and estimating a more complete representation of the state distribution as an accurate approximation of a full PDF. The PF uses Monte Carlo runs to generate particles that approximate the full PDF representation. The PF is applied in the estimation and propagation of a highly eccentric orbit and the results are compared to the Extended Kalman Filter and Splitting Gaussian Mixture algorithms to demonstrate its proficiency.

Wall-collision line broadening of molecular oxygen within nanoporous materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Can T.; Lewander, Maerta; Andersson-Engels, Stefan

2011-10-15

Wall-collision broadening of near-infrared absorption lines of molecular oxygen confined in nanoporous zirconia is studied by employing high-resolution diode-laser spectroscopy. The broadening is studied for pores of different sizes under a range of pressures, providing new insights on how wall collisions and intermolecular collisions influence the total spectroscopic line profile. The pressure series show that wall-collision broadening is relatively more prominent under reduced pressures, enabling sensitive means to probe pore sizes of porous materials. In addition, we show that the total wall-collision-broadened profile strongly deviates from a Voigt profile and that wall-collision broadening exhibits an additive-like behavior to the pressuremore » and Doppler broadening.« less

Effects of lead time of verbal collision warning messages on driving behavior in connected vehicle settings.

PubMed

Wan, Jingyan; Wu, Changxu; Zhang, Yiqi

2016-09-01

Under the connected vehicle environment, vehicles will be able to exchange traffic information with roadway infrastructure and other vehicles. With such information, collision warning systems (CWSs) will be able to warn drivers with potentially hazardous situations within or out of sight and reduce collision accidents. The lead time of warning messages is a crucial factor in determining the effectiveness of CWSs in the prevention of traffic accidents. Accordingly, it is necessary to understand the effects of lead time on driving behaviors and explore the optimal lead time in various collision scenarios. The present driving simulator experiment studied the effects of controlled lead time at 16 levels (predetermined time headway from the subject vehicle to the collision location when the warning message broadcasted to a driver) on driving behaviors in various collision scenarios. Maximum effectiveness of warning messages was achieved when the controlled lead time was within the range of 5s to 8s. Specifically, the controlled lead time ranging from 4s to 8s led to the optimal safety benefit; and the controlled lead time ranging from 5s to 8s led to more gradual braking and shorter reaction time. Furthermore, a trapezoidal distribution of warning effectiveness was found by building a statistic model using curve estimation considering lead time, lifetime driving experience, and driving speed. The results indicated that the controlled lead time significantly affected driver performance. The findings have implications for the design of collision warning systems. Copyright © 2016 Elsevier Ltd and National Safety Council. All rights reserved.

Recommendations for Sense and Avoid Policy Compliance

NASA Technical Reports Server (NTRS)

2005-01-01

Since unmanned aircraft do not have a human on board, they need to have a sense and avoid capability that provides an "equivalent level of safety" (ELOS) to manned aircraft. The question then becomes - is sense and avoid ELOS for unmanned aircraft adequate to satisfy the requirements of 14 CFR 91.113? Access 5 has proposed a definition of sense and avoid, but the question remains as to whether any sense and avoid system can comply with 14 CFR 91.113 as currently written. The Access 5 definition of sense and avoid ELOS allows for the development of a sense and avoid system for unmanned aircraft that would comply with 14 CFR 91.113. Compliance is based on sensing and avoiding other traffic at an equivalent level of safety for collision avoidance, as manned aircraft. No changes to Part 91 are necessary, with the possible exception of changing "see" to "sense," or obtaining an interpretation from the FAA General Counsel that "sense" is equivalent to "see."

Translational Entanglement and Teleportation of Matter Wavepackets by Collisions and Half-Collisions

NASA Astrophysics Data System (ADS)

Fisch, L.; Tal, A.; Kurizki, G.

To date, the translationally-entangled state originally proposed by Einstein, Podolsky and Rosen (EPR) in 1935 has not been experimentally realized for massive particles. Opatrný and Kurizki [Phys. Rev. Lett. 86, 3180 (2000)] have suggested the creation of a position- and momentum-correlated, i.e., translationally-entangled, pair of particles approximating the EPR state by dissociation of cold diatomic molecules, and further manipulation of the EPR pair effecting matter-wave teleportation. Here we aim at setting the principles of and quantifying translational entanglement by collisions and half-collisions. In collisions, the resonance width s and the initial phase-space distributions are shown to determine the degree of post-collisional momentum entanglement. Half-collisions (dissociation) are shown to yield different types of approximate EPR states. We analyse a feasible realization of translational EPR entanglement and teleportation via cold-molecule Raman dissociation and subsequent collisions, resolving both practical and conceptual difficulties it has faced so far: How to avoid entanglement loss due to the wavepacket spreading of the dissociation fragments? How to measure both position and momentum correlations of the dissociation fragments with sufficient accuracy to verify their EPR correlations? How to reliably perform two-particle (Bell) position and momentum measurements on one of the fragments and the wavepacket to be teleported?

Colliding nuclei to colliding galaxies: Illustrations using a simple colliding liquid-drop apparatus

NASA Astrophysics Data System (ADS)

Becchetti, F. D.; Mack, S. L.; Robinson, W. R.; Ojaruega, M.

2015-10-01

A simple apparatus suitable for observing the collisions between drops of fluids of various properties is described. Typical results are shown for experiments performed by undergraduate students using various types of fluids. The collisions take place under free-fall (zero-g) conditions, with analysis employing digital video. Two specific types of collisions are examined in detail, head-on collisions and peripheral, grazing collisions. The collisions for certain fluids illustrate many types of nuclear collisions and provide useful insight into these processes, including both fusion and non-fusion outcomes, often with the formation of exotic shapes or emission of secondary fragments. Collisions of other liquids show a more chaotic behavior, often resembling galactic collisions. As expected, the Weber number associated with a specific collision impact parameter is found to be the important quantity in determining the initial outcome of these colliding systems. The features observed resemble those reported by others using more elaborate experimental techniques.

Small Collision Systems at RHIC

NASA Astrophysics Data System (ADS)

Novitzky, Norbert

2018-02-01

The observation of long range correlations in highly asymmetric systems, as in p+Pb and d+Au collisions, suggests a creation of a medium with collective behavior. It is still an open question if the quark-gluon plasma is formed in these collision. Hence, the RHIC collider invested time to study the small systems in different collision systems and energies. Here we discuss the recent results from the PHENIX and STAR collaborations in four different collision systems p+Al, p+Au, d+Au and 3He+Au at = 200 GeV, and also for the energy scan in d+Au collisions between = 19.6 - 200 GeV.

Effect of collision duration on the chaotic dynamics of a ball bouncing on a vertically vibrating plate

NASA Astrophysics Data System (ADS)

Jiang, Z. H.; Liang, Z. J.; Wu, A. C.; Zheng, R. H.

2018-03-01

Experiments have been performed to study the chaotic dynamics of a ball bouncing on a vertically vibrating plate. The velocity dependence of collision duration and coefficient of restitution is determined, and phase portraits of chaotic structures for the flight time and the relative collision velocities are obtained. Numerical calculations are carried out to examine the effects of velocity-dependent collision duration on the ball dynamics. It is revealed that when the collision is instantaneous, sticking solutions are always observed, whereas when the collision duration is taken into account, sticking solutions are destroyed and thereby chaos behaviors are induced.

Use and Understanding of the Proximate Status Indication in Traffic Displays

DOT National Transportation Integrated Search

2011-10-16

Traffic Collision Avoidance System (TCAS) traffic displays use symbol fill to distinguish proximate from non-proximate targets, where proximate targets are within a specified range and altitude of ownship, and non-proximate targets are ou...

Assessment of IVHS countermeasures for collision avoidance : rear-end crashes

DOT National Transportation Integrated Search

1993-05-01

This report describe an analysis of the application of Intelligent : Vehicle Highway System (IVHS) technology to the reduction of rear-end crashes. The : principal countermeasure concept examined is a headway detection (HD) system that : would detect...

Over height impact avoidance and incident detection system : research project capsule.

DOT National Transportation Integrated Search

2016-07-01

During the construction and repair of bridges, work platforms or construction-related : containment may result in restricted vertical clearances at a work : location. Some tractor-trailer combinations are prone to over-height collisions : at these lo...

Run-Off-Road Collision Avoidance Countermeasures Using IVHS Countermeasures, Task 3, Volume 1, Final Report

DOT National Transportation Integrated Search

1995-08-01

KEYWORDS : RESEARCH AND DEVELOPMENT OR R&D, CRASH REDUCTION, FATALITIES REDUCTION, LATERAL GUIDANCE, LONGITUDINAL GUIDANCE, ADVANCED VEHICLE CONTROL & SAFETY SYSTEMS OR AVCSS, ADVANCED VEHICLE CONTROL SYSTEM OR AVCS, INTELLIGENT VEHICLE INITIATIV...

An extended car-following model to describe connected traffic dynamics under cyberattacks

NASA Astrophysics Data System (ADS)

Wang, Pengcheng; Yu, Guizhen; Wu, Xinkai; Qin, Hongmao; Wang, Yunpeng

2018-04-01

In this paper, the impacts of the potential cyberattacks on vehicles are modeled through an extended car-following model. To better understand the mechanism of traffic disturbance under cyberattacks, the linear and nonlinear stability analysis are conducted respectively. Particularly, linear stability analysis is performed to obtain different neutral stability conditions with various parameters; and nonlinear stability analysis is carried out by using reductive perturbation method to derive the soliton solution of the modified Korteweg de Vries equation (mKdV) near the critical point, which is used to draw coexisting stability lines. Furthermore, by applying linear and nonlinear stability analysis, traffic flow state can be divided into three states, i.e., stable, metastable and unstable states which are useful to describe shockwave dynamics and driving behaviors under cyberattacks. The theoretical results show that the proposed car-following model is capable of successfully describing the car-following behavior of connected vehicles with cyberattacks. Finally, numerical simulation using real values has confirmed the validity of theoretical analysis. The results further demonstrate our model can be used to help avoid collisions and relieve traffic congestion with cybersecurity threats.

Background factors associated with problem avoidance behavior in healthy partners of breast cancer patients.

PubMed

Shiozaki, Mariko; Sanjo, Makiko; Hirai, Kei

2017-08-01

We evaluated avoidance behaviors of healthy partners of breast cancer patients and sought to (1) describe men's perception of their own avoidance behavior and (2) identify the background factors associated with such behavior. An Internet-based survey was conducted, and analysis was performed on the responses of 368 male spouses of female breast cancer patients. Thirty to forty percent of spouses had some type of problem avoidance behavior toward their wives. There was a high correlation (r = 0.70, P < .001) between problem avoidance behavior at the time of diagnosis and subsequent problem behavior (mean follow-up period after diagnosis: 1.3 + 1.1 years). The characteristics of spouses with avoidant behaviors included having wives with recurrence, having wives treated with anticancer drug therapy or total resection, and having their own experience of cancer. Covariance structure analysis revealed 2 factors related to the background of spouses with problem avoidance behavior: (1) having a sense of difficulty in coping (beta = 0.68, P < .001) and (2) having a poor marital relationship (beta = -0.27, P < .001). Our findings suggest that problem avoidance behavior among healthy male partners of breast cancer patients is common and correlates with difficulty coping and a poor marital relationship. It is important to address both the problem avoidance behavior itself and to support couples early, before this behavior surfaces. Copyright © 2016 John Wiley & Sons, Ltd.

Crash avoidance potential of four passenger vehicle technologies.

PubMed

Jermakian, Jessica S

2011-05-01

The objective was to update estimates of maximum potential crash reductions in the United States associated with each of four crash avoidance technologies: side view assist, forward collision warning/mitigation, lane departure warning/prevention, and adaptive headlights. Compared with previous estimates (Farmer, 2008), estimates in this study attempted to account for known limitations of current systems. Crash records were extracted from the 2004-08 files of the National Automotive Sampling System General Estimates System (NASS GES) and the Fatality Analysis Reporting System (FARS). Crash descriptors such as vehicle damage location, road characteristics, time of day, and precrash maneuvers were reviewed to determine whether the information or action provided by each technology potentially could have prevented or mitigated the crash. Of the four crash avoidance technologies, forward collision warning/mitigation had the greatest potential for preventing crashes of any severity; the technology is potentially applicable to 1.2 million crashes in the United States each year, including 66,000 serious and moderate injury crashes and 879 fatal crashes. Lane departure warning/prevention systems appeared relevant to 179,000 crashes per year. Side view assist and adaptive headlights could prevent 395,000 and 142,000 crashes per year, respectively. Lane departure warning/prevention was relevant to the most fatal crashes, up to 7500 fatal crashes per year. A combination of all four current technologies potentially could prevent or mitigate (without double counting) up to 1,866,000 crashes each year, including 149,000 serious and moderate injury crashes and 10,238 fatal crashes. If forward collision warning were extended to detect objects, pedestrians, and bicyclists, it would be relevant to an additional 3868 unique fatal crashes. There is great potential effectiveness for vehicle-based crash avoidance systems. However, it is yet to be determined how drivers will interact with the systems. The actual effectiveness of these systems will not be known until sufficient real-world experience has been gained. Copyright © 2010 Elsevier Ltd. All rights reserved.

Need for reaction coordinates to ensure a complete basis set in an adiabatic representation of ion-atom collisions

NASA Astrophysics Data System (ADS)

Rabli, Djamal; McCarroll, Ronald

2018-02-01

This review surveys the different theoretical approaches, used to describe inelastic and rearrangement processes in collisions involving atoms and ions. For a range of energies from a few meV up to about 1 keV, the adiabatic representation is expected to be valid and under these conditions, inelastic and rearrangement processes take place via a network of avoided crossings of the potential energy curves of the collision system. In general, such avoided crossings are finite in number. The non-adiabatic coupling, due to the breakdown of the Born-Oppenheimer separation of the electronic and nuclear variables, depends on the ratio of the electron mass to the nuclear mass terms in the total Hamiltonian. By limiting terms in the total Hamiltonian correct to first order in the electron to nuclear mass ratio, a system of reaction coordinates is found which allows for a correct description of both inelastic channels. The connection between the use of reaction coordinates in the quantum description and the electron translation factors of the impact parameter approach is established. A major result is that only when reaction coordinates are used, is it possible to introduce the notion of a minimal basis set. Such a set must include all avoided crossings including both radial coupling and long range Coriolis coupling. But, only when reactive coordinates are used, can such a basis set be considered as complete. In particular when the centre of nuclear mass is used as centre of coordinates, rather than the correct reaction coordinates, it is shown that erroneous results are obtained. A few results to illustrate this important point are presented: one concerning a simple two-state Landau-Zener type avoided crossing, the other concerning a network of multiple crossings in a typical electron capture process involving a highly charged ion with a neutral atom.

Grasping objects autonomously in simulated KC-135 zero-g

NASA Technical Reports Server (NTRS)

Norsworthy, Robert S.

1994-01-01

The KC-135 aircraft was chosen for simulated zero gravity testing of the Extravehicular Activity Helper/retriever (EVAHR). A software simulation of the EVAHR hardware, KC-135 flight dynamics, collision detection and grasp inpact dynamics has been developed to integrate and test the EVAHR software prior to flight testing on the KC-135. The EVAHR software will perform target pose estimation, tracking, and motion estimation for rigid, freely rotating, polyhedral objects. Manipulator grasp planning and trajectory control software has also been developed to grasp targets while avoiding collisions.

Safe Maritime Navigation with COLREGS Using Velocity Obstacles

NASA Technical Reports Server (NTRS)

Kuwata, Yoshiaki; Wolf, Michael T.; Zarzhitsky, Dimitri; Huntsberger, Terrance L.

2011-01-01

This paper presents a motion planning algorithm for Unmanned Surface Vehicles (USVs) to navigate safely in dynamic, cluttered environments. The proposed algorithm not only addresses Hazard Avoidance (HA) for stationary and moving hazards but also applies the International Regulations for Preventing Collisions at Sea (known as COLREGs). The COLREG rules specify, for example, which vessel is responsible for giving way to the other and to which side of the "stand-on" vessel to maneuver. The three primary COLREG rules were considered in this paper: crossing, overtaking, and head-on situations. For USVs to be safely deployed in environments with other traffic boats, it is imperative that the USV's navigation algorithm obey COLREGs. Note also that if other boats disregard their responsibility under COLREGs, the USV will still apply its HA algorithms to avoid a collision. The proposed approach is based on Velocity Obstacles, which generates a cone-shaped obstacle in the velocity space. Because Velocity Obstacles also specify which side of the obstacle the vehicle will pass during the avoidance maneuver, COLREGs are encoded in the velocity space in a natural way. The algorithm is demonstrated via both simulation and on-water tests.

Unified solution of the Boltzmann equation for electron and ion velocity distribution functions and transport coefficients in weakly ionized plasmas

NASA Astrophysics Data System (ADS)

Konovalov, Dmitry A.; Cocks, Daniel G.; White, Ronald D.

2017-10-01

The velocity distribution function and transport coefficients for charged particles in weakly ionized plasmas are calculated via a multi-term solution of Boltzmann's equation and benchmarked using a Monte-Carlo simulation. A unified framework for the solution of the original full Boltzmann's equation is presented which is valid for ions and electrons, avoiding any recourse to approximate forms of the collision operator in various limiting mass ratio cases. This direct method using Lebedev quadratures over the velocity and scattering angles avoids the need to represent the ion mass dependence in the collision operator through an expansion in terms of the charged particle to neutral mass ratio. For the two-temperature Burnett function method considered in this study, this amounts to avoiding the need for the complex Talmi-transformation methods and associated mass-ratio expansions. More generally, we highlight the deficiencies in the two-temperature Burnett function method for heavy ions at high electric fields to calculate the ion velocity distribution function, even though the transport coefficients have converged. Contribution to the Topical Issue "Physics of Ionized Gases (SPIG 2016)", edited by Goran Poparic, Bratislav Obradovic, Dragana Maric and Aleksandar Milosavljevic.

Step 1:Human System Integration (HSI) FY05 Pilot-Technology Interface Requirements for Collision Avoidance

NASA Technical Reports Server (NTRS)

2007-01-01

This document provides definition of technology human interface requirements for Collision Avoidance (CA). This was performed through a review of CA-related, HSI requirements documents, standards, and recommended practices. Technology concepts in use by the Access 5 CA work package were considered... Beginning with the HSI high-level functional requirement for CA, and CA technology elements, HSI requirements for the interface to the pilot were identified. Results of the analysis describe (1) the information required by the pilot to have knowledge CA system status, and (2) the control capability needed by the pilot to obtain CA information and affect an avoidance maneuver. Fundamentally, these requirements provide the candidate CA technology concepts with the necessary human-related elements to make them compatible with human capabilities and limitations. The results of the analysis describe how CA operations and functions should interface with the pilot to provide the necessary CA functionality to the UA-pilot system .Requirements and guidelines for CA are partitioned into four categories: (1) General, (2) Alerting, (3) Guidance, and (4) Cockpit Display of Traffic Information. Each requirement is stated and is supported with a rationale and associated reference(s).

RAC-multi: reader anti-collision algorithm for multichannel mobile RFID networks.

PubMed

Shin, Kwangcheol; Song, Wonil

2010-01-01

At present, RFID is installed on mobile devices such as mobile phones or PDAs and provides a means to obtain information about objects equipped with an RFID tag over a multi-channeled telecommunication networks. To use mobile RFIDs, reader collision problems should be addressed given that readers are continuously moving. Moreover, in a multichannel environment for mobile RFIDs, interference between adjacent channels should be considered. This work first defines a new concept of a reader collision problem between adjacent channels and then suggests a novel reader anti-collision algorithm for RFID readers that use multiple channels. To avoid interference with adjacent channels, the suggested algorithm separates data channels into odd and even numbered channels and allocates odd-numbered channels first to readers. It also sets an unused channel between the control channel and data channels to ensure that control messages and the signal of the adjacent channel experience no interference. Experimental results show that suggested algorithm shows throughput improvements ranging from 29% to 46% for tag identifications compared to the GENTLE reader anti-collision algorithm for multichannel RFID networks.

RAC-Multi: Reader Anti-Collision Algorithm for Multichannel Mobile RFID Networks

PubMed Central

Shin, Kwangcheol; Song, Wonil

2010-01-01

At present, RFID is installed on mobile devices such as mobile phones or PDAs and provides a means to obtain information about objects equipped with an RFID tag over a multi-channeled telecommunication networks. To use mobile RFIDs, reader collision problems should be addressed given that readers are continuously moving. Moreover, in a multichannel environment for mobile RFIDs, interference between adjacent channels should be considered. This work first defines a new concept of a reader collision problem between adjacent channels and then suggests a novel reader anti-collision algorithm for RFID readers that use multiple channels. To avoid interference with adjacent channels, the suggested algorithm separates data channels into odd and even numbered channels and allocates odd-numbered channels first to readers. It also sets an unused channel between the control channel and data channels to ensure that control messages and the signal of the adjacent channel experience no interference. Experimental results show that suggested algorithm shows throughput improvements ranging from 29% to 46% for tag identifications compared to the GENTLE reader anti-collision algorithm for multichannel RFID networks. PMID:22315528

Permeability of roads to movement of scrubland lizards and small mammals

USGS Publications Warehouse

Brehme, Cheryl S.; Tracey, Jeff A.; McClenaghan, Leroy R.; Fisher, Robert N.

2013-01-01

A primary objective of road ecology is to understand and predict how roads affect connectivity of wildlife populations. Road avoidance behavior can fragment populations, whereas lack of road avoidance can result in high mortality due to wildlife-vehicle collisions. Many small animal species focus their activities to particular microhabitats within their larger habitat. We sought to assess how different types of roads affect the movement of small vertebrates and to explore whether responses to roads may be predictable on the basis of animal life history or microhabitat preferences preferences. We tracked the movements of fluorescently marked animals at 24 sites distributed among 3 road types: low-use dirt, low-use secondary paved, and rural 2-lane highway. Most data we collected were on the San Diego pocket mouse (Chaetodipus fallax), cactus mouse (Peromyscus eremicus), western fence lizard (Sceloporus occidentalis), orange-throated whiptail (Aspidoscelis hyperythra), Dulzura kangaroo rat (Dipodomys simulans) (dirt, secondary paved), and deer mouse (Peromyscus maniculatus) (highway only). San Diego pocket mice and cactus mice moved onto dirt roads but not onto a low-use paved road of similar width or onto the highway, indicating they avoidpaved road substrate. Both lizard species moved onto the dirt and secondary paved roads but avoided the rural 2-lane rural highway, indicating they may avoid noise, vibration, or visual disturbance from a steady flow of traffic. Kangaroo rats did not avoid the dirt or secondary paved roads. Overall, dirt and secondary roads were more permeable to species that prefer to forage or bask in open areas of their habitat, rather than under the cover of rocks or shrubs. However, all study species avoided the rural 2-lane highway. Our results suggest that microhabitat use preferences and road substrate help predict species responses to low-use roads,but roads with heavy traffic may deter movement of a much wider range of small animal species.

Data Link Test and Analysis System/TCAS Monitor User's Guide

DOT National Transportation Integrated Search

1991-02-01

This document is a user's guide for the Data Link Test and Analysis System : (DATAS) Traffic Alert and Collision Avoidance System (TCAS) monitor application. : It provides a brief overall hardware description of DATAS configured as a TCAS : Monitor, ...

Test Results of Initial Installation DATAS/TCAS Monitor: DFW Airport

DOT National Transportation Integrated Search

1992-01-01

This document presents the results of initial tests with the Data Link Test and : Analysis System (DATAS)/Traffic Alert and Collision Avoidance System (TCAS). : Since a significant amount of air carriers have recently been equipped with : Traffic Ale...

Frankfurt, Germany: 1030/1090 MegaHertz Signal Analysis

DOT National Transportation Integrated Search

1996-07-01

The Data Link Test Analysis System (DATAS) was used in the Frankfort, Germany : to collect data in the frequency band used by Air Traffic Control Radar : Beacon (ATCRBS), Mode Select (Mode S), and Traffic Alert and Collision : Avoidance (TCAS). Data ...

50 CFR 218.33 - Mitigation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... take proper and effective action to avoid a collision with any marine animal and can be stopped within... and Fisheries NATIONAL MARINE FISHERIES SERVICE, NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking...

English Leadership Quarterly, 1993.

ERIC Educational Resources Information Center

Strickland, James, Ed.

1993-01-01

These four issues of the English Leadership Quarterly represent those published during 1993. Articles in number 1 deal with parent involvement and participation, and include: "Opening the Doors to Open House" (Jolene A. Borgese); "Parent/Teacher Conferences: Avoiding the Collision Course" (Robert Perrin); "Expanding Human…

Branch-Based Centralized Data Collection for Smart Grids Using Wireless Sensor Networks

PubMed Central

Kim, Kwangsoo; Jin, Seong-il

2015-01-01

A smart grid is one of the most important applications in smart cities. In a smart grid, a smart meter acts as a sensor node in a sensor network, and a central device collects power usage from every smart meter. This paper focuses on a centralized data collection problem of how to collect every power usage from every meter without collisions in an environment in which the time synchronization among smart meters is not guaranteed. To solve the problem, we divide a tree that a sensor network constructs into several branches. A conflict-free query schedule is generated based on the branches. Each power usage is collected according to the schedule. The proposed method has important features: shortening query processing time and avoiding collisions between a query and query responses. We evaluate this method using the ns-2 simulator. The experimental results show that this method can achieve both collision avoidance and fast query processing at the same time. The success rate of data collection at a sink node executing this method is 100%. Its running time is about 35 percent faster than that of the round-robin method, and its memory size is reduced to about 10% of that of the depth-first search method. PMID:26007734

Branch-based centralized data collection for smart grids using wireless sensor networks.

PubMed

Kim, Kwangsoo; Jin, Seong-il

2015-05-21

A smart grid is one of the most important applications in smart cities. In a smart grid, a smart meter acts as a sensor node in a sensor network, and a central device collects power usage from every smart meter. This paper focuses on a centralized data collection problem of how to collect every power usage from every meter without collisions in an environment in which the time synchronization among smart meters is not guaranteed. To solve the problem, we divide a tree that a sensor network constructs into several branches. A conflict-free query schedule is generated based on the branches. Each power usage is collected according to the schedule. The proposed method has important features: shortening query processing time and avoiding collisions between a query and query responses. We evaluate this method using the ns-2 simulator. The experimental results show that this method can achieve both collision avoidance and fast query processing at the same time. The success rate of data collection at a sink node executing this method is 100%. Its running time is about 35 percent faster than that of the round-robin method, and its memory size is reduced to about 10% of that of the depth-first search method.

Autonomous collision avoidance system by combined control of steering and braking using geometrically optimised vehicular trajectory

NASA Astrophysics Data System (ADS)

Hayashi, Ryuzo; Isogai, Juzo; Raksincharoensak, Pongsathorn; Nagai, Masao

2012-01-01

This study proposes an autonomous obstacle avoidance system not only by braking but also by steering, as one of the active safety technologies to prevent traffic accidents. The proposed system prevents the vehicle from colliding with a moving obstacle like a pedestrian jumping out from the roadside. In the proposed system, to avoid the predicted colliding position based on constant-velocity obstacle motion assumption, the avoidance trajectory is derived as connected two identical arcs. The system then controls the vehicle autonomously by the combined control of the braking and steering systems. In this paper, the proposed system is examined by real car experiments and its effectiveness is shown from the results of the experiments.

Navigational choice between reversal and curve during acidic pH avoidance behavior in Caenorhabditis elegans.

PubMed

Wakabayashi, Tokumitsu; Sakata, Kazumi; Togashi, Takuya; Itoi, Hiroaki; Shinohe, Sayaka; Watanabe, Miwa; Shingai, Ryuzo

2015-11-19

Under experimental conditions, virtually all behaviors of Caenorhabditis elegans are achieved by combinations of simple locomotion, including forward, reversal movement, turning by deep body bending, and gradual shallow turning. To study how worms regulate these locomotion in response to sensory information, acidic pH avoidance behavior was analyzed by using worm tracking system. In the acidic pH avoidance, we characterized two types of behavioral maneuvers that have similar behavioral sequences in chemotaxis and thermotaxis. A stereotypic reversal-turn-forward sequence of reversal avoidance caused an abrupt random reorientation, and a shallow gradual turn in curve avoidance caused non-random reorientation in a less acidic direction to avoid the acidic pH. Our results suggest that these two maneuvers were each triggered by a distinct threshold pH. A simulation study using the two-distinct-threshold model reproduced the avoidance behavior of the real worm, supporting the presence of the threshold. Threshold pH for both reversal and curve avoidance was altered in mutants with reduced or enhanced glutamatergic signaling from acid-sensing neurons. C. elegans employ two behavioral maneuvers, reversal (klinokinesis) and curve (klinotaxis) to avoid acidic pH. Unlike the chemotaxis in C. elegans, reversal and curve avoidances were triggered by absolute pH rather than temporal derivative of stimulus concentration in this behavior. The pH threshold is different between reversal and curve avoidance. Mutant studies suggested that the difference results from a differential amount of glutamate released from ASH and ASK chemosensory neurons.

The Top 10 Questions for Active Debris Removal

NASA Technical Reports Server (NTRS)

Liou, J. -C.

2010-01-01

This slide presentation reviews the requirement and issues around removal of debris from the earth orbital environment. The 10 questions discussed are: 1. Which region (LEO/MEO/GEO) has the fastest projected growth rate and the highest collision activities? 2. Can the commonly-adopted mitigation measures stabilize the future environment? 3. What are the objectives of active debris removal (ADR)? 4. How can effective ADR target selection criteria to stabilize the future LEO environment be defined? 5. What are the keys to remediate the future LEO environment? 6. What is the timeframe for ADR implementation? 7. What is the effect of practical/operational constraints? 8. What are the collision probabilities and masses of the current objects? 9. What are the benefits of collision avoidance maneuvers? 10. What is the next step?

A Numerical Approach to Estimate the Ballistic Coefficient of Space Debris from TLE Orbital Data

NASA Technical Reports Server (NTRS)

Narkeliunas, Jonas

2016-01-01

Low Earth Orbit (LEO) is full of space debris, which consist of spent rocket stages, old satellites and fragments from explosions and collisions. As of 2009, more than 21,000 orbital debris larger than 10 cm are known to exist], and while it is hard to track anything smaller than that, the estimated population of particles between 1 and 10 cm in diameter is approximately 500,000, whereas small as 1 cm exceeds 100 million. These objects orbit Earth with huge kinetic energies speeds usually exceed 7 kms. The shape of their orbit varies from almost circular to highly elliptical and covers all LEO, a region in space between 160 and 2,000 km above sea level. Unfortunately, LEO is also the place where most of our active satellites are situated, as well as, International Space Station (ISS) and Hubble Space Telescope, whose orbits are around 400 and 550 km above sea level, respectively.This poses a real threat as debris can collide with satellites and deal substantial damage or even destroy them.Collisions between two or more debris create clouds of smaller debris, which are harder to track and increase overall object density and collision probability. At some point, the debris density couldthen reach a critical value, which would start a chain reaction and the number of space debris would grow exponentially. This phenomenon was first described by Kessler in 1978 and he concluded that it would lead to creation of debris belt, which would vastly complicate satellite operations in LEO. The debris density is already relatively high, as seen from several necessary debris avoidance maneuvers done by Shuttle, before it was discontinued, and ISS. But not all satellites have a propulsion system to avoid collision, hence different methods need to be applied. One of the proposed collision avoidance concepts is called LightForce and it suggests using photon pressure to induce small orbital corrections to deflect debris from colliding. This method is very efficient as seen from theoretical simulations, even few continuous mode 10 kW ground-based lasers, focused by 1.5 m telescopes with adaptive optics, were enough to prevent significant amount of the debris collisions. Simulations were done by propagating all space objects in LEO by 1 year into the future and checking whether the probability of collision was high. For those space objects different ground-based lasers were used to divert them, afterwards collision probabilities were reevaluated. However, the actual accuracy of the LightForce software, which has been developed at NASA AmesResearch Center, depends on the veracity of the input parameters, one of which is the objects ballistic coefficient. It is a measure of bodys ability to overcome air resistance, which has a significant impact on the debris in LEO, and thus it is responsible for the shape of the trajectory of the debris. Having the exact values of the ballistic coefficient would make significantly better collision predictions, unfortunately, we do not know what are the values for most of the objects.In this research, we were working with part of LightForce code, which estimates the ballistic coefficient from ephemerides. Previously used method gave highly inaccurate values, when compared to known objects, and it needed to be changed. The goal of this work was to try out a different method of estimating the ballistic coefficient and to check whether or not it gives noticeable improvements.

Analysis of Well-Clear Boundary Models for the Integration of UAS in the NAS

NASA Technical Reports Server (NTRS)

Upchurch, Jason M.; Munoz, Cesar A.; Narkawicz, Anthony J.; Chamberlain, James P.; Consiglio, Maria C.

2014-01-01

The FAA-sponsored Sense and Avoid Workshop for Unmanned Aircraft Systems (UAS) defnes the concept of sense and avoid for remote pilots as "the capability of a UAS to remain well clear from and avoid collisions with other airborne traffic." Hence, a rigorous definition of well clear is fundamental to any separation assurance concept for the integration of UAS into civil airspace. This paper presents a family of well-clear boundary models based on the TCAS II Resolution Advisory logic. Analytical techniques are used to study the properties and relationships satisfied by the models. Some of these properties are numerically quantifed using statistical methods.

Frequency of distracting tasks people do while driving : an analysis of the ACAS FOT data.

DOT National Transportation Integrated Search

2007-06-01

This report describes further analysis of data from the advanced collision avoidance system (ACAS) field operational test, a naturalistic driving study. To determine how distracted and nondistracted driving differ, a stratified sample of 2,914 video ...

How do distracted and normal driving differ : an analysis of the ACAS naturalistic driving data

DOT National Transportation Integrated Search

2007-05-01

To determine how distracted and normal driving differ, this report re-examines : driving performance data from the advanced collision avoidance system (ACAS) field : operational test (FOT), a naturalistic driving study (96 drivers, 136,792 miles). : ...

Data link test and analysis system/TCAS monitor user's guide

NASA Astrophysics Data System (ADS)

Vandongen, John; Wapelhorst, Leo

1991-02-01

This document is a user's guide for the Data Link Test and Analysis System (DATAS) Traffic Alert and Collision Avoidance System (TCAS) monitor. It provides a brief overall hardware description of DATAS configured as a TCAS monitor, and the applications software.

Application of DGPS for Collision Avoidance in Intelligent Transportation Systems In a Wireless Environment

DOT National Transportation Integrated Search

2001-02-19

The Global Positioning System (GPS) is a satellite based radio-navigation system. A relatively large number of vehicles are already equipped with GPS devices. This project evaluated the application of Global Positing System (GPS) technology in collis...

Traffic Alert and Collision Avoidance System. Developmental Simulation.

DTIC Science & Technology

1982-07-01

deck system concepts, fuinctional capailities, and interface features. Proposed ;ystpms, system chanoes , and Alternative mechanizations can he evaluated...What chanoes should be made in the voice? Clarify limit command D-8 .A . .. .. . . . 10. Does the modification of the TYSI by addition Of command

NADS versus CAMP closed-course comparison examining "last-second" braking and steering maneuvers under various kinematic conditions

DOT National Transportation Integrated Search

2005-08-01

Drivers last-second braking and last-second steering judgments have been studied extensively by the Crash Avoidance Metrics Partnership (CAMP) Forward Collision Warning (FCW) Requirements project. This previous work was conducted under closed-cour...

The usefulness of the proximate status indication as represented by symbol fill on cockpit displays of traffic information

DOT National Transportation Integrated Search

2013-06-30

Traffic Alert and Collision Avoidance Systems (TCAS) displays depict traffic advisories, resolution advisories, and information on other aircraft. Symbols for other aircraft include the proximate status indication where the symbols of proximate...

50 CFR 218.33 - Mitigation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... take proper and effective action to avoid a collision with any marine animal and can be stopped within... Wildlife and Fisheries NATIONAL MARINE FISHERIES SERVICE, NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking...

50 CFR 218.33 - Mitigation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... take proper and effective action to avoid a collision with any marine animal and can be stopped within... Wildlife and Fisheries NATIONAL MARINE FISHERIES SERVICE, NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking...

A Hierarchy of Heuristic-Based Models of Crowd Dynamics

NASA Astrophysics Data System (ADS)

Degond, P.; Appert-Rolland, C.; Moussaïd, M.; Pettré, J.; Theraulaz, G.

2013-09-01

We derive a hierarchy of kinetic and macroscopic models from a noisy variant of the heuristic behavioral Individual-Based Model of Ngai et al. (Disaster Med. Public Health Prep. 3:191-195, 2009) where pedestrians are supposed to have constant speeds. This IBM supposes that pedestrians seek the best compromise between navigation towards their target and collisions avoidance. We first propose a kinetic model for the probability distribution function of pedestrians. Then, we derive fluid models and propose three different closure relations. The first two closures assume that the velocity distribution function is either a Dirac delta or a von Mises-Fisher distribution respectively. The third closure results from a hydrodynamic limit associated to a Local Thermodynamical Equilibrium. We develop an analogy between this equilibrium and Nash equilibria in a game theoretic framework. In each case, we discuss the features of the models and their suitability for practical use.

An elevated plus-maze in mixed reality for studying human anxiety-related behavior.

PubMed

Biedermann, Sarah V; Biedermann, Daniel G; Wenzlaff, Frederike; Kurjak, Tim; Nouri, Sawis; Auer, Matthias K; Wiedemann, Klaus; Briken, Peer; Haaker, Jan; Lonsdorf, Tina B; Fuss, Johannes

2017-12-21

A dearth of laboratory tests to study actual human approach-avoidance behavior has complicated translational research on anxiety. The elevated plus-maze (EPM) is the gold standard to assess approach-avoidance behavior in rodents. Here, we translated the EPM to humans using mixed reality through a combination of virtual and real-world elements. In two validation studies, we observed participants' anxiety on a behavioral, physiological, and subjective level. Participants reported higher anxiety on open arms, avoided open arms, and showed an activation of endogenous stress systems. Participants' with high anxiety exhibited higher avoidance. Moreover, open arm avoidance was moderately predicted by participants' acrophobia and sensation seeking, with opposing influences. In a randomized, double blind, placebo controlled experiment, GABAergic stimulation decreased avoidance of open arms while alpha-2-adrenergic antagonism increased avoidance. These findings demonstrate cross-species validity of open arm avoidance as a translational measure of anxiety. We thus introduce the first ecologically valid assay to track actual human approach-avoidance behavior under laboratory conditions.

A Monte Carlo simulation of the effect of ion self-collisions on the ion velocity distribution function in the high-latitude F-region

NASA Technical Reports Server (NTRS)

Barghouthi, I. A.; Barakat, A. R.; Schunk, R. W.

1994-01-01

Non-Maxwellian ion velocity distribution functions have been theoretically predicted and confirmed by observations, to occur at high latitudes. These distributions deviate from Maxwellian due to the combined effect of the E x B drift and ion-neutral collisions. At high altitude and/or for solar maximum conditions, the ion-to-neutral density ratio increases and, hence, the role of ion self-collisions becomes appreciable. A Monte Carlo simulation was used to investigate the behavior of O(+) ions that are E x B-drifting through a background of neutral O, with the effect of O(+) (Coulomb) self-collisions included. Wide ranges of the ion-to-neutral density ratio n(sub i)/n(sub n) and the electrostatic field E were considered in order to investigate the change of ion behavior with solar cycle and with altitude. For low altitudes and/or solar minimum (n(sub i)/n(sub n) less than or equal to 10(exp -5)), the effect of self-collisions is negligible. For higher values of n(sub i)/n(sub n), the effect of self-collisions becomes significant and, hence, the non-Maxwellian features of the O(+) distribution are reduced. The Monte Carlo results were compared to those that used simplified collision models in order to assess their validity. In general, the simple collision models tend to be more accurate for low E and for high n(sub i)/n(sub n).

The Suborbital Particle Aggregation and Collision Experiment (SPACE): studying the collision behavior of submillimeter-sized dust aggregates on the suborbital rocket flight REXUS 12.

PubMed

Brisset, Julie; Heißelmann, Daniel; Kothe, Stefan; Weidling, René; Blum, Jürgen

2013-09-01

The Suborbital Particle Aggregation and Collision Experiment (SPACE) is a novel approach to study the collision properties of submillimeter-sized, highly porous dust aggregates. The experiment was designed, built, and carried out to increase our knowledge about the processes dominating the first phase of planet formation. During this phase, the growth of planetary precursors occurs by agglomeration of micrometer-sized dust grains into aggregates of at least millimeters to centimeters in size. However, the formation of larger bodies from the so-formed building blocks is not yet fully understood. Recent numerical models on dust growth lack a particular support by experimental studies in the size range of submillimeters, because these particles are predicted to collide at very gentle relative velocities of below 1 cm/s that can only be achieved in a reduced-gravity environment. The SPACE experiment investigates the collision behavior of an ensemble of silicate-dust aggregates inside several evacuated glass containers which are being agitated by a shaker to induce the desired collisions at chosen velocities. The dust aggregates are being observed by a high-speed camera, allowing for the determination of the collision properties of the protoplanetary dust analog material. The data obtained from the suborbital flight with the REXUS (Rocket Experiments for University Students) 12 rocket will be directly implemented into a state-of-the-art dust growth and collision model.

Exaggerated acquisition and resistance to extinction of avoidance behavior in treated heroin-dependent men.

PubMed

Sheynin, Jony; Moustafa, Ahmed A; Beck, Kevin D; Servatius, Richard J; Casbolt, Peter A; Haber, Paul; Elsayed, Mahmoud; Hogarth, Lee; Myers, Catherine E

2016-03-01

Addiction is often conceptualized as a behavioral strategy for avoiding negative experiences. In rodents, opioid intake has been associated with abnormal acquisition and extinction of avoidance behavior. Here, we tested the hypothesis that these findings would generalize to human opioid-dependent subjects. Adults meeting DSM-IV criteria for heroin dependence and treated with opioid medication (n = 27) and healthy controls (n = 26) were recruited between March 2013 and October 2013 and given a computer-based task to assess avoidance behavior. For this task, subjects controlled a spaceship and could either gain points by shooting an enemy spaceship or hide in safe areas to avoid on-screen aversive events. Hiding duration during different periods of the task was used to measure avoidance behavior. While groups did not differ on escape responding (hiding) during the aversive event, heroin-dependent men (but not women) made more avoidance responses during a warning signal that predicted the aversive event (analysis of variance, sex × group interaction, P = .007). Heroin-dependent men were also slower to extinguish the avoidance response when the aversive event no longer followed the warning signal (P = .011). This behavioral pattern resulted in reduced opportunity to obtain reward without reducing risk of punishment. Results suggest that, in male patients, differences in avoidance behavior cannot be easily explained by impaired task performance or by exaggerated motor activity. This study provides evidence for abnormal acquisition and extinction of avoidance behavior in opioid-dependent patients. Interestingly, data suggest that abnormal avoidance is demonstrated only by male patients. Findings shed light on cognitive and behavioral manifestations of opioid addiction and may facilitate development of therapeutic approaches to help affected individuals. © Copyright 2016 Physicians Postgraduate Press, Inc.

Avoidant coping partially mediates the relationship between patient problem behaviors and depressive symptoms in spousal Alzheimer caregivers.

PubMed

Mausbach, Brent T; Aschbacher, Kirstin; Patterson, Thomas L; Ancoli-Israel, Sonia; von Känel, Roland; Mills, Paul J; Dimsdale, Joel E; Grant, Igor

2006-04-01

Caring for a loved one with Alzheimer disease is a highly stressful experience that is associated with significant depressive symptoms. Previous studies indicate a positive association between problem behaviors in patients with Alzheimer disease (e.g., repeating questions, restlessness, and agitation) and depressive symptoms in their caregivers. Moreover, the extant literature indicates a robust negative relationship between escape-avoidance coping (i.e., avoiding people, wishing the situation would go away) and psychiatric well-being. The purpose of this study was to test a mediational model of the associations between patient problem behaviors, escape-avoidance coping, and depressive symptoms in Alzheimer caregivers. Ninety-five spousal caregivers (mean age: 72 years) completed measures assessing their loved ones' frequency of problem behaviors, escape-avoidance coping, and depressive symptoms. A mediational model was tested to determine if escape-avoidant coping partially mediated the relationship between patient problem behaviors and caregiver depressive symptoms. Patient problem behaviors were positively associated with escape-avoidance coping (beta = 0.38, p < 0.01) and depressive symptoms (beta = 0.26, p < 0.05). Escape-avoidance coping was positively associated with depressive symptoms (beta = 0.33, p < 0.01). In a final regression analysis, the impact of problem behaviors on depressive symptoms was less after controlling for escape-avoidance coping. Sobel's test confirmed that escape-avoidance coping significantly mediated the relationship between problem behaviors and depressive symptoms (z = 2.07, p < 0.05). Escape-avoidance coping partially mediates the association between patient problem behaviors and depressive symptoms among elderly caregivers of spouses with dementia. This finding provides a specific target for psychosocial interventions for caregivers.

Launch Collision Probability

NASA Technical Reports Server (NTRS)

Bollenbacher, Gary; Guptill, James D.

1999-01-01

This report analyzes the probability of a launch vehicle colliding with one of the nearly 10,000 tracked objects orbiting the Earth, given that an object on a near-collision course with the launch vehicle has been identified. Knowledge of the probability of collision throughout the launch window can be used to avoid launching at times when the probability of collision is unacceptably high. The analysis in this report assumes that the positions of the orbiting objects and the launch vehicle can be predicted as a function of time and therefore that any tracked object which comes close to the launch vehicle can be identified. The analysis further assumes that the position uncertainty of the launch vehicle and the approaching space object can be described with position covariance matrices. With these and some additional simplifying assumptions, a closed-form solution is developed using two approaches. The solution shows that the probability of collision is a function of position uncertainties, the size of the two potentially colliding objects, and the nominal separation distance at the point of closest approach. ne impact of the simplifying assumptions on the accuracy of the final result is assessed and the application of the results to the Cassini mission, launched in October 1997, is described. Other factors that affect the probability of collision are also discussed. Finally, the report offers alternative approaches that can be used to evaluate the probability of collision.

Situation analysis for automotive pre-crash systems

NASA Astrophysics Data System (ADS)

Böhning, Marcus A.; Ritter, Henning; Rohling, Herrman

2008-01-01

According to the "World Report on Road Traffic Injury Prevention" jointly issued by the World Health Organization and the World Bank about 1.2 million people are killed and up to 50 million people are injured in road traffic accidents worldwide each year. While passive safety systems like the airbag are already deployed successfully to reduce fatalities and injuries, active safety systems assist the driver by issuing a warning or by taking corrective actions to either avoid a collision completely or, if impossible, to mitigate collision consequences. Today's radar sensors have the ability to detect and track objects with a high accuracy in range and velocity, therefore a collision warning system may consist of a radar sensor, a data processing unit and a model to describe possible evasion maneuvers. This allows to analyze the probability of a collision and to calculate the danger potential of the current situation. In this paper, such a system is proposed and it is verified with synthetic as well as real sensor data.

Predictions of asteroid hazard to the Earth for the 21st century

NASA Astrophysics Data System (ADS)

Petrov, Nikita; Sokolov, Leonid; Polyakhova, Elena; Oskina, Kristina

2018-05-01

Early detection and investigation of possible collisions and close approaches of asteroids with the Earth are necessary to exept the asteroid-comet hazard. The difficulty of prediction of close approaches and collisions associated with resonant returns after encounters with the Earth due to loss of precision in these encounters. The main research object is asteroid Apophis (99942), for which we found many possible orbits of impacts associated with resonant returns. It is shown that the early orbit change of Apophis allows to avoid main impacts, associated with resonant returns. Such a change of the orbit, in principle, is feasible. We also study the possible impacts with the Ground asteroid 2015 RN35. We present 21 possible collisions in this century, including 7 collisions with large gaps presented in NASA website. The results of observations by the telescope ZA-320M at Pulkovo Obser-vatory of the three near-Earth asteroids, namely, 7822, 20826, 68216, two of which 7822 and 68216 are potentially hazardous, are presented.

Healthcare avoidance: a critical review.

PubMed

Byrne, Sharon K

2008-01-01

The purpose of this study is to provide a critical review and synthesis of theoretical and research literature documenting the impact of avoidance on healthcare behaviors, identify the factors that influence healthcare avoidance and delay in the adult population, and propose a direction for future research. The Theory of Reasoned Action, Theory of Planned Behavior, Theory of Care-Seeking Behavior, the Transtheoretical Model, and the Behavioral Model of Health Services Use/Utilization are utilized to elaborate on the context within which individual intention to engage in healthcare behaviors occurs. Research literature on the concept of healthcare avoidance obtained by using computerized searches of CINAHL, MEDLINE, PSYCH INFO, and HAPI databases, from 1995 to 2007, were reviewed. Studies were organized by professional disciplines. Healthcare avoidance is a common and highly variable experience. Multiple administrative, demographic, personal, and provider factors are related to healthcare avoidance, for example, distrust of providers and/or the science community, health beliefs, insurance status, or socioeconomic/income level. Although the concept is recognized by multiple disciplines, limited research studies address its impact on healthcare decision making. More systematic research is needed to determine correlates of healthcare avoidance. Such studies will help investigators identify patients at risk for avoidant behaviors and provide the basis for health-promoting interventions. Methodological challenges include identification of characteristics of individuals and environments that hinder healthcare behaviors, as well as, the complexity of measuring healthcare avoidance. Studies need to systematically explore the influence of avoidance behaviors on specific healthcare populations at risk.

Anisotropic kinetic energy release and gyroscopic behavior of CO2 super rotors from an optical centrifuge.

PubMed

Murray, Matthew J; Ogden, Hannah M; Mullin, Amy S

2017-10-21

An optical centrifuge is used to generate an ensemble of CO 2 super rotors with oriented angular momentum. The collision dynamics and energy transfer behavior of the super rotor molecules are investigated using high-resolution transient IR absorption spectroscopy. New multipass IR detection provides improved sensitivity to perform polarization-dependent transient studies for rotational states with 76 ≤ J ≤ 100. Polarization-dependent measurements show that the collision-induced kinetic energy release is spatially anisotropic and results from both near-resonant energy transfer between super rotor molecules and non-resonant energy transfer between super rotors and thermal molecules. J-dependent studies show that the extent and duration of the orientational anisotropy increase with rotational angular momentum. The super rotors exhibit behavior akin to molecular gyroscopes, wherein molecules with larger amounts of angular momentum are less likely to change their angular momentum orientation through collisions.

Anisotropic kinetic energy release and gyroscopic behavior of CO2 super rotors from an optical centrifuge

NASA Astrophysics Data System (ADS)

Murray, Matthew J.; Ogden, Hannah M.; Mullin, Amy S.

2017-10-01

An optical centrifuge is used to generate an ensemble of CO2 super rotors with oriented angular momentum. The collision dynamics and energy transfer behavior of the super rotor molecules are investigated using high-resolution transient IR absorption spectroscopy. New multipass IR detection provides improved sensitivity to perform polarization-dependent transient studies for rotational states with 76 ≤ J ≤ 100. Polarization-dependent measurements show that the collision-induced kinetic energy release is spatially anisotropic and results from both near-resonant energy transfer between super rotor molecules and non-resonant energy transfer between super rotors and thermal molecules. J-dependent studies show that the extent and duration of the orientational anisotropy increase with rotational angular momentum. The super rotors exhibit behavior akin to molecular gyroscopes, wherein molecules with larger amounts of angular momentum are less likely to change their angular momentum orientation through collisions.

A novel passive micromixer based on unbalanced splits and collisions of fluid streams

NASA Astrophysics Data System (ADS)

Ansari, Mubashshir Ahmad; Kim, Kwang-Yong; Anwar, Khalid; Kim, Sun Min

2010-05-01

A new passive micromixer based on the concept of unbalanced splits and cross-collisions of fluid streams is designed and fabricated. Experimental and numerical studies have been carried out on the micromixer at Reynolds numbers ranging from 10 to 80. The three-dimensional Navier-Stokes equations have been used to analyze the mixing and flow behavior of the micromixer, which is composed of two sub-channels of unequal widths which repeatedly undergo splitting and recombination. The difference between the mass flow rates in the two sub-channels creates an unbalanced collision of the two fluid streams. Mixing is mainly due to the combined effect of unbalanced collisions of the fluid streams and Dean vortices. The micromixer shows interesting mixing behavior for different ratios of the widths of the two split sub-channels. The sub-channels wherein the major sub-channel is twice as wide as the minor sub-channel exhibit the highest mixing performance at Reynolds numbers larger than 40. The results show the lowest mixing performance for the case of uniform width, where balanced collisions occur.

Flight response to spatial and temporal correlates informs risk from wind turbines to the California Condor

USGS Publications Warehouse

Poessel, Sharon; Brandt, Joseph; Mendenhall, Laura C.; Braham, Melissa A.; Lanzone, Michael J.; McGann, Andrew J.; Katzner, Todd

2018-01-01

Wind power is a fast-growing energy resource, but wind turbines can kill volant wildlife, and the flight behavior of obligate soaring birds can place them at risk of collision with these structures. We analyzed altitudinal data from GPS telemetry of critically endangered California Condors (Gymnogyps californianus) to assess the circumstances under which their flight behavior may place them at risk from collision with wind turbines. Condor flight behavior was strongly influenced by topography and land cover, and birds flew at lower altitudes and closer to the rotor-swept zone of wind turbines when over ridgelines and steep slopes and over forested and grassland cover types. Condor flight behavior was temporally predictable, and birds flew lower and closer to the rotor-swept zone during early morning and evening hours and during the winter months, when thermal updrafts were weakest. Although condors only occasionally flew at altitudes that placed them in the rotor-swept zone of turbines, they regularly flew near or within wind resource areas preferred by energy developers. Practitioners aiming to mitigate collision risk to this and other soaring bird species of conservation concern can consider the manner in which flight behavior varies temporally and in response to areas of high topographic relief and proximity to nocturnal roosting sites. By contrast, collision risk to large soaring birds from turbines should be relatively lower over flatter and less rugged areas and in habitat used during daytime soaring.

Development of the KARI Space Debris Collision Risk Management System (KARISMA)

NASA Astrophysics Data System (ADS)

Kim, Hae-Dong; Lee, Sang-Cherl; Cho, Dong-Hyun; Seong, Jae-Dong

2018-05-01

Korea has been operating multi-purpose low-earth orbit (LEO) satellites such as the Korea multi-purpose satellite (KOMPSAT) since 1999 and the Communication, Ocean, and Meteorological Satellite (COMS), which was launched into geostationary orbit in 2006. The Korea Aerospace Research Institute (KARI) consequently became concerned about the deteriorating space debris environment. This led to the instigation, in 2011, of a project to develop the KARI space debris collision risk management system (KARISMA). In 2014, KARISMA was adopted as an official tool at the KARI ground station and is operated to mitigate collision risks while being continuously upgraded with input from satellite operators. The characteristics and architecture of KARISMA are described with detailed operational views. The user-friendly user interfaces including 2D and 3D displays of the results, conjunction geometries, and so on, are described in detail. The results of our analysis of the space collision risk faced by the KOMPSAT satellites as determined using KARISMA are presented, as well as optimized collision avoidance maneuver planning with maneuvering strategies for several conjunction events. Consequently, the development of KARISMA to provide detailed descriptions is expected to contribute significantly to satellite operators and owners who require tools with many useful functions to mitigate collision risk.

Design and performance evaluation of collision protection-based safety operation for a haptic robot-assisted catheter operating system.

PubMed

Zhang, Linshuai; Guo, Shuxiang; Yu, Huadong; Song, Yu; Tamiya, Takashi; Hirata, Hideyuki; Ishihara, Hidenori

2018-02-23

The robot-assisted catheter system can increase operating distance thus preventing the exposure radiation of the surgeon to X-ray for endovascular catheterization. However, few designs have considered the collision protection between the catheter tip and the vessel wall. This paper presents a novel catheter operating system based on tissue protection to prevent vessel puncture caused by collision. The integrated haptic interface not only allows the operator to feel the real force feedback, but also combines with the newly proposed collision protection mechanism (CPM) to mitigate the collision trauma. The CPM can release the catheter quickly when the measured force exceeds a certain threshold, so as to avoid the vessel puncture. A significant advantage is that the proposed mechanism can adjust the protection threshold in real time by the current according to the actual characteristics of the blood vessel. To verify the effectiveness of the tissue protection by the system, the evaluation experiments in vitro were carried out. The results show that the further collision damage can be effectively prevented by the CPM, which implies the realization of relative safe catheterization. This research provides some insights into the functional improvements of safe and reliable robot-assisted catheter systems.

Driving performance analysis of the ACAS FOT data and recommendations for a driving workload manager.

DOT National Transportation Integrated Search

2006-12-01

This report contains analyses of driving performance data from the Advanced Collision Avoidance System (ACAS) Field Operational Test (FOT), with data from nearly 100 drivers and over 100,000 miles of driving. The analyses compared normal and distract...

Development of collision avoidance for light vehicles : near-crash/crash event data recorders

DOT National Transportation Integrated Search

2006-12-01

This report presents the results of an analysis effort undertaken to address the following research question: What sensor(s) can be cost effectively added to vehicles on a wide scale to significantly improve the understanding and modeling of naturali...

14 CFR Appendix D to Part 25 - Appendix D to Part 25

Code of Federal Regulations, 2014 CFR

2014-01-01

..., electronic controls, pressurization system controls, and engine controls. (2) The accessibility and... considered: (1) Flight path control. (2) Collision avoidance. (3) Navigation. (4) Communications. (5) Operation and monitoring of aircraft engines and systems. (6) Command decisions. (b) Workload factors. The...

14 CFR Appendix D to Part 25 - Appendix D to Part 25

Code of Federal Regulations, 2010 CFR

2010-01-01

..., electronic controls, pressurization system controls, and engine controls. (2) The accessibility and... considered: (1) Flight path control. (2) Collision avoidance. (3) Navigation. (4) Communications. (5) Operation and monitoring of aircraft engines and systems. (6) Command decisions. (b) Workload factors. The...

14 CFR Appendix D to Part 25 - Appendix D to Part 25

Code of Federal Regulations, 2011 CFR

2011-01-01

..., electronic controls, pressurization system controls, and engine controls. (2) The accessibility and... considered: (1) Flight path control. (2) Collision avoidance. (3) Navigation. (4) Communications. (5) Operation and monitoring of aircraft engines and systems. (6) Command decisions. (b) Workload factors. The...

14 CFR Appendix D to Part 25 - Appendix D to Part 25

Code of Federal Regulations, 2012 CFR

2012-01-01

..., electronic controls, pressurization system controls, and engine controls. (2) The accessibility and... considered: (1) Flight path control. (2) Collision avoidance. (3) Navigation. (4) Communications. (5) Operation and monitoring of aircraft engines and systems. (6) Command decisions. (b) Workload factors. The...

Road-Following Formation Control of Autonomous Ground Vehicles

NASA Technical Reports Server (NTRS)

Ono, Masahiro; Droge, Greg; Grip, Havard; Toupet, Olivier; Scrapper, Chris; Rahmani, Amir

2015-01-01

This work presents a novel cooperative path planning for formation keeping robots traversing along a road with obstacles and possible narrow passages. A unique challenge in this problem is a requirement for spatial and temporal coordination between vehicles while ensuring collision and obstacle avoidance.

Scenarios for Evolution of Air Traffic Control,

DTIC Science & Technology

1981-11-01

decisionmaking systems. We have thus approached it from the perspectives of computer science, engineering, human-factors psychology , and the emerging field of...assurance monitor or indepen- dent collision-avoidance system like ATARS could prevent the acci- 35 dent), but there will undoubtedly be other situations

A TCAS-II Resolution Advisory Detection Algorithm

NASA Technical Reports Server (NTRS)

Munoz, Cesar; Narkawicz, Anthony; Chamberlain, James

2013-01-01

The Traffic Alert and Collision Avoidance System (TCAS) is a family of airborne systems designed to reduce the risk of mid-air collisions between aircraft. TCASII, the current generation of TCAS devices, provides resolution advisories that direct pilots to maintain or increase vertical separation when aircraft distance and time parameters are beyond designed system thresholds. This paper presents a mathematical model of the TCASII Resolution Advisory (RA) logic that assumes accurate aircraft state information. Based on this model, an algorithm for RA detection is also presented. This algorithm is analogous to a conflict detection algorithm, but instead of predicting loss of separation, it predicts resolution advisories. It has been formally verified that for a kinematic model of aircraft trajectories, this algorithm completely and correctly characterizes all encounter geometries between two aircraft that lead to a resolution advisory within a given lookahead time interval. The RA detection algorithm proposed in this paper is a fundamental component of a NASA sense and avoid concept for the integration of Unmanned Aircraft Systems in civil airspace.

A Virtual Audio Guidance and Alert System for Commercial Aircraft Operations

NASA Technical Reports Server (NTRS)

Begault, Durand R.; Wenzel, Elizabeth M.; Shrum, Richard; Miller, Joel; Null, Cynthia H. (Technical Monitor)

1996-01-01

Our work in virtual reality systems at NASA Ames Research Center includes the area of aurally-guided visual search, using specially-designed audio cues and spatial audio processing (also known as virtual or "3-D audio") techniques (Begault, 1994). Previous studies at Ames had revealed that use of 3-D audio for Traffic Collision Avoidance System (TCAS) advisories significantly reduced head-down time, compared to a head-down map display (0.5 sec advantage) or no display at all (2.2 sec advantage) (Begault, 1993, 1995; Begault & Pittman, 1994; see Wenzel, 1994, for an audio demo). Since the crew must keep their head up and looking out the window as much as possible when taxiing under low-visibility conditions, and the potential for "blunder" is increased under such conditions, it was sensible to evaluate the audio spatial cueing for a prototype audio ground collision avoidance warning (GCAW) system, and a 3-D audio guidance system. Results were favorable for GCAW, but not for the audio guidance system.

Avoiding space robot collisions utilizing the NASA/GSFC tri-mode skin sensor

NASA Technical Reports Server (NTRS)

Prinz, F. B. S.; Mahalingam, S.

1992-01-01

A capacitance based proximity sensor, the 'Capaciflector' (Vranish 92), has been developed at the Goddard Space Flight Center of NASA. We had investigated the use of this sensor for avoiding and maneuvering around unexpected objects (Mahalingam 92). The approach developed there would help in executing collision-free gross motions. Another important aspect of robot motion planning is fine motion planning. Let us classify manipulator robot motion planning into two groups at the task level: gross motion planning and fine motion planning. We use the term 'gross planning' where the major degrees of freedom of the robot execute large motions, for example, the motion of a robot in a pick and place type operation. We use the term 'fine motion' to indicate motions of the robot where the large dofs do not move much, and move far less than the mirror dofs, such as in inserting a peg in a hole. In this report we describe our experiments and experiences in this area.

Region-Based Collision Avoidance Beaconless Geographic Routing Protocol in Wireless Sensor Networks.

PubMed

Lee, JeongCheol; Park, HoSung; Kang, SeokYoon; Kim, Ki-Il

2015-06-05

Due to the lack of dependency on beacon messages for location exchange, the beaconless geographic routing protocol has attracted considerable attention from the research community. However, existing beaconless geographic routing protocols are likely to generate duplicated data packets when multiple winners in the greedy area are selected. Furthermore, these protocols are designed for a uniform sensor field, so they cannot be directly applied to practical irregular sensor fields with partial voids. To prevent the failure of finding a forwarding node and to remove unnecessary duplication, in this paper, we propose a region-based collision avoidance beaconless geographic routing protocol to increase forwarding opportunities for randomly-deployed sensor networks. By employing different contention priorities into the mutually-communicable nodes and the rest of the nodes in the greedy area, every neighbor node in the greedy area can be used for data forwarding without any packet duplication. Moreover, simulation results are given to demonstrate the increased packet delivery ratio and shorten end-to-end delay, rather than well-referred comparative protocols.

Region-Based Collision Avoidance Beaconless Geographic Routing Protocol in Wireless Sensor Networks

PubMed Central

Lee, JeongCheol; Park, HoSung; Kang, SeokYoon; Kim, Ki-Il

2015-01-01

Due to the lack of dependency on beacon messages for location exchange, the beaconless geographic routing protocol has attracted considerable attention from the research community. However, existing beaconless geographic routing protocols are likely to generate duplicated data packets when multiple winners in the greedy area are selected. Furthermore, these protocols are designed for a uniform sensor field, so they cannot be directly applied to practical irregular sensor fields with partial voids. To prevent the failure of finding a forwarding node and to remove unnecessary duplication, in this paper, we propose a region-based collision avoidance beaconless geographic routing protocol to increase forwarding opportunities for randomly-deployed sensor networks. By employing different contention priorities into the mutually-communicable nodes and the rest of the nodes in the greedy area, every neighbor node in the greedy area can be used for data forwarding without any packet duplication. Moreover, simulation results are given to demonstrate the increased packet delivery ratio and shorten end-to-end delay, rather than well-referred comparative protocols. PMID:26057037

Integrated Display and Simulation for Automatic Dependent Surveillance–Broadcast and Traffic Collision Avoidance System Data Fusion

PubMed Central

Wang, Yanran; Xiao, Gang; Dai, Zhouyun

2017-01-01

Automatic Dependent Surveillance–Broadcast (ADS-B) is the direction of airspace surveillance development. Research analyzing the benefits of Traffic Collision Avoidance System (TCAS) and ADS-B data fusion is almost absent. The paper proposes an ADS-B minimum system from ADS-B In and ADS-B Out. In ADS-B In, a fusion model with a variable sampling Variational Bayesian-Interacting Multiple Model (VSVB-IMM) algorithm is proposed for integrated display and an airspace traffic situation display is developed by using ADS-B information. ADS-B Out includes ADS-B Out transmission based on a simulator platform and an Unmanned Aerial Vehicle (UAV) platform. This paper describes the overall implementation of ADS-B minimum system, including theoretical model design, experimental simulation verification, engineering implementation, results analysis, etc. Simulation and implementation results show that the fused system has better performance than each independent subsystem and it can work well in engineering applications. PMID:29137194

Comparing and validating models of driver steering behaviour in collision avoidance and vehicle stabilisation

NASA Astrophysics Data System (ADS)

Markkula, G.; Benderius, O.; Wahde, M.

2014-12-01

A number of driver models were fitted to a large data set of human truck driving, from a simulated near-crash, low-friction scenario, yielding two main insights: steering to avoid a collision was best described as an open-loop manoeuvre of predetermined duration, but with situation-adapted amplitude, and subsequent vehicle stabilisation could to a large extent be accounted for by a simple yaw rate nulling control law. These two phenomena, which could be hypothesised to generalise to passenger car driving, were found to determine the ability of four driver models adopted from the literature to fit the human data. Based on the obtained results, it is argued that the concept of internal vehicle models may be less valuable when modelling driver behaviour in non-routine situations such as near-crashes, where behaviour may be better described as direct responses to salient perceptual cues. Some methodological issues in comparing and validating driver models are also discussed.

Analysis of Compression Algorithm in Ground Collision Avoidance Systems (Auto-GCAS)

NASA Technical Reports Server (NTRS)

Schmalz, Tyler; Ryan, Jack

2011-01-01

Automatic Ground Collision Avoidance Systems (Auto-GCAS) utilizes Digital Terrain Elevation Data (DTED) stored onboard a plane to determine potential recovery maneuvers. Because of the current limitations of computer hardware on military airplanes such as the F-22 and F-35, the DTED must be compressed through a lossy technique called binary-tree tip-tilt. The purpose of this study is to determine the accuracy of the compressed data with respect to the original DTED. This study is mainly interested in the magnitude of the error between the two as well as the overall distribution of the errors throughout the DTED. By understanding how the errors of the compression technique are affected by various factors (topography, density of sampling points, sub-sampling techniques, etc.), modifications can be made to the compression technique resulting in better accuracy. This, in turn, would minimize unnecessary activation of A-GCAS during flight as well as maximizing its contribution to fighter safety.

All-optical LAN architectures based on arrayed waveguide grating multiplexers

NASA Astrophysics Data System (ADS)

Woesner, Hagen

1998-10-01

The paper presents optical LAN topologies which are made possible using an Arrayed Waveguide Grating Multiplexer (AWGM) instead of a passive star coupler to interconnect stations in an all-optical LAN. Due to the collision-free nature of an AWGM it offers the n-fold bandwidth compared to the star coupler. Virtual ring topologies appear (one ring on each wavelength) if the number of stations attached to the AWGM is a prime number. A method to construct larger networks using Cayley graphs is shown. An access protocol to avoid collisions on the proposed network is outlined.

Collision Avoidance, Driver Support and Safety Intervention Systems

NASA Astrophysics Data System (ADS)

Gilling, Simon P.

Autonomous Intelligent Cruise Control (AICC) will be marketed by a number of vehicle manufacturers before the end of the decade. This paper will describe AICC and the next generation systems currently being developed and validated within the EC Fourth Framework project, Anti-Collision Autonomous Support and Safety Intervention SysTem (AC ASSIST).The currently available cruise control systems which maintain a fixed speed are a well-known form of longitudinal driver support. The fixed speed cruise control becomes less useful with increased traffic volumes, as the driver must disable the system when a slower preceding vehicle is encountered.

Post Deflection Impact Risk Analysis of the Double Asteroid Redirection Test (DART)

NASA Astrophysics Data System (ADS)

Eggl, S.; Hestroffer, D.

2017-09-01

Collisions between potentially hazardous near-Earth objects and our planet are among the few natural disasters that can be avoided by human intervention. The complexity of such an endeavor necessitates an asteroid orbit deflection test mission, however, ensuring all relevant knowledge is present when an asteroid on a collision course with the Earth is indeed discovered. The double asteroid redirection test (DART) mission concept currently investigated by NASA would serve such a purpose. The aim of our research is to make certain that DART does not turn a previously harmless asteroid into a potentially dangerous one.

The MIT - Cornell Collision and Why it Happened

DTIC Science & Technology

2008-10-01

George Boulevard Ben and Team UCF’s Knight Rider Section 2.2 2h00m North Nevada and Red Zone CarOLO’s Caroline turns across MIT’s Talos Section 2.3...3h00m White Zone Caroline and Talos collide. Section 2.4 4h00m Carolina Avenue and Texas Avenue Talos swerves to avoid Victor Tango’s Odin Section 2.5...stopped in time to prevent a collision. 2.3 Caroline and Talos at North Nevada and Red Zone N or th N ev ad a Av e C ar ol in a Av e Red Zone

Real life safety benefits of increasing brake deceleration in car-to-pedestrian accidents: Simulation of Vacuum Emergency Braking.

PubMed

Jeppsson, Hanna; Östling, Martin; Lubbe, Nils

2018-02-01

The objective of this study is to predict the real-life benefits, namely the number of injuries avoided rather than the reduction in impact speed, offered by a Vacuum Emergency Brake (VEB) added to a pedestrian automated emergency braking (AEB) system. We achieve this through the virtual simulation of simplified mathematical models of a system which incorporates expected future advances in technology, such as a wide sensor field of view, and reductions in the time needed for detection, classification, and brake pressure build up. The German In-Depth Accident Study database and the related Pre Crash Matrix, both released in the beginning of 2016, were used for this study and resulted in a final sample of 526 collisions between passenger car fronts and pedestrians. Weight factors were calculated for both simulation model and injury risk curves to make the data representative of Germany as a whole. The accident data was used with a hypothetical AEB system in a simulation model, and injury risk was calculated from the new impact speed using injury risk curves to generate new situations using real accidents. Adding a VEB to a car with pedestrian AEB decreased pedestrian casualties by an additional 8-22%, depending on system setting and injury level, over the AEB-only system. The overall decrease in fatalities was 80-87%, an improvement of 8%. Collision avoidance was improved by 14-28%. VEB with a maximum deceleration in the middle of the modelled performance range has an effectiveness similar to that of an "early activation" system, where the AEB is triggered as early as 2 s before collision. VEB may therefore offer a substantial increase in performance without increasing false positive rates, which earlier AEB activation does. Most collisions and injuries can be avoided when AEB is supplemented by the high performance VEB; remaining cases are characterised by high pedestrian walking speed and late visibility due to view obstructions. VEB is effective in all analysed accident scenarios. Copyright © 2017 Elsevier Ltd. All rights reserved.

Operational support to collision avoidance activities by ESA's space debris office

NASA Astrophysics Data System (ADS)

Braun, V.; Flohrer, T.; Krag, H.; Merz, K.; Lemmens, S.; Bastida Virgili, B.; Funke, Q.

2016-09-01

The European Space Agency's (ESA) Space Debris Office provides a service to support operational collision avoidance activities. This support currently covers ESA's missions Cryosat-2, Sentinel-1A and -2A, the constellation of Swarm-A/B/C in low-Earth orbit (LEO), as well as missions of third-party customers. In this work, we describe the current collision avoidance process for ESA and third-party missions in LEO. We give an overview on the upgrades developed and implemented since the advent of conjunction summary messages (CSM)/conjunction data messages (CDM), addressing conjunction event detection, collision risk assessment, orbit determination, orbit and covariance propagation, process control, and data handling. We pay special attention to the effect of warning thresholds on the risk reduction and manoeuvre rates, as they are established through risk mitigation and analysis tools, such as ESA's Debris Risk Assessment and Mitigation Analysis (DRAMA) software suite. To handle the large number of CDMs and the associated risk analyses, a database-centric approach has been developed. All CDMs and risk analysis results are stored in a database. In this way, a temporary local "mini-catalogue" of objects close to our target spacecraft is obtained, which can be used, e.g., for manoeuvre screening and to update the risk analysis whenever a new ephemeris becomes available from the flight dynamics team. The database is also used as the backbone for a Web-based tool, which consists of the visualization component and a collaboration tool that facilitates the status monitoring and task allocation within the support team as well as communication with the control team. The visualization component further supports the information sharing by displaying target and chaser motion over time along with the involved uncertainties. The Web-based solution optimally meets the needs for a concise and easy-to-use way to obtain a situation picture in a very short time, and the support for third-party missions not operated from the European Space Operations Centre (ESOC). Finally, we provide statistics on the identified conjunction events, taking into account the known significant changes in the LEO orbital environment and share ESA's experience along with recent examples.

Combining radar and direct observation to estimate pelican collision risk at a proposed wind farm on the Cape west coast, South Africa

PubMed Central

Reid, Tim; du Plessis, Johan; Colyn, Robin; Benn, Grant; Millikin, Rhonda

2018-01-01

Pre-construction assessments of bird collision risk at proposed wind farms are often confounded by insufficient or poor quality data describing avian flight paths through the development area. These limitations can compromise the practical value of wind farm impact studies. We used radar- and observer-based methods to quantify great white pelican flights in the vicinity of a planned wind farm on the Cape west coast, South Africa, and modelled turbine collision risk under various scenarios. Model outputs were combined with pre-existing demographic data to evaluate the possible influence of the wind farm on the pelican population, and to examine impact mitigation options. We recorded high volumes of great white pelican movement through the wind farm area, coincident with the breeding cycle of the nearby colony and associated with flights to feeding areas located about 50 km away. Pelicans were exposed to collision risk at a mean rate of 2.02 High Risk flights.h-1. Risk was confined to daylight hours, highest during the middle of the day and in conditions of strong north-westerly winds, and 82% of High Risk flights were focused on only five of the proposed 35 turbine placements. Predicted mean mortality rates (22 fatalities.yr-1, 95% Cl, 16–29, with average bird and blade speeds and 95% avoidance rates) were not sustainable, resulting in a negative population growth rate (λ = 0.991). Models suggested that removal of the five highest risk turbines from the project, or institution of a curtailment regimen that shuts down at least these turbines at peak traffic times, could theoretically reduce impacts to manageable levels. However, in spite of the large quantities of high quality data used in our analyses, our collision risk model remains compromised by untested assumptions about pelican avoidance rates and uncertainties about the existing dynamics of the pelican population, and our findings are probably not reliable enough to ensure sustainable development. PMID:29408877

TU-G-BRB-01: Continuous Path Optimization for Non-Coplanar Variant SAD IMRT Delivery Using C-Arm Machines.

PubMed

Ruan, D; Dong, P; Low, D; Sheng, K

2012-06-01

To develop and investigate a continuous path optimization methodology to traverse prescribed non-coplanar IMRT beams with variant SADs, by orchestrating the couch and gantry movement with zero-collision, minimal patient motion consequence and machine travel time. We convert the given collision zone definition and the prescribed beam location/angles to a tumor-centric coordinate, and represent the traversing path as a continuous open curve. We proceed to optimize a composite objective function consisting of (1) a strong attraction energy to ensure all prescribed beams are en-route, (2) a penalty for patient-motion inducing couch motion, and (3) a penalty for travel-time inducing overall path-length. Feasibility manifold is defined as complement to collision zone and the optimization is performed with a level set representation evolved with variational flows. The proposed method has been implemented and tested on clinically derived data. In the absence of any existing solutions for the same problem, we validate by: (1) visual inspecting the generated path rendered in the 3D tumor-centric coordinates, and (2) comparing with a traveling-salesman (TSP) solution obtained from relaxing the variant SADs and continuous collision-avoidance requirement. The proposed method has generated delivery paths that are smooth and intuitively appealing. Under relaxed settings, our results outperform the generic TSP solutions and agree with specially tuned versions. We have proposed a novel systematic approach that automatically determines the continuous path to cover non-coplanar, varying SAD IMRT beams. The proposed approach accommodates patient-specific collision zone definition and ensures its avoidance continuously. The differential penalty to couch and gantry motions allows customizable tradeoff between patient geometry stability and delivery efficiency. This development paves the path to achieve safe, accurate and efficient non-coplanar IMRT delivery with the advanced robotic controls in new-generation C-arm systems, enabling practical harvesting of the dose benefit offered by non-coplanar, variant SAD IMRT treatment. © 2012 American Association of Physicists in Medicine.

Combining radar and direct observation to estimate pelican collision risk at a proposed wind farm on the Cape west coast, South Africa.

PubMed

Jenkins, Andrew R; Reid, Tim; du Plessis, Johan; Colyn, Robin; Benn, Grant; Millikin, Rhonda

2018-01-01

Pre-construction assessments of bird collision risk at proposed wind farms are often confounded by insufficient or poor quality data describing avian flight paths through the development area. These limitations can compromise the practical value of wind farm impact studies. We used radar- and observer-based methods to quantify great white pelican flights in the vicinity of a planned wind farm on the Cape west coast, South Africa, and modelled turbine collision risk under various scenarios. Model outputs were combined with pre-existing demographic data to evaluate the possible influence of the wind farm on the pelican population, and to examine impact mitigation options. We recorded high volumes of great white pelican movement through the wind farm area, coincident with the breeding cycle of the nearby colony and associated with flights to feeding areas located about 50 km away. Pelicans were exposed to collision risk at a mean rate of 2.02 High Risk flights.h-1. Risk was confined to daylight hours, highest during the middle of the day and in conditions of strong north-westerly winds, and 82% of High Risk flights were focused on only five of the proposed 35 turbine placements. Predicted mean mortality rates (22 fatalities.yr-1, 95% Cl, 16-29, with average bird and blade speeds and 95% avoidance rates) were not sustainable, resulting in a negative population growth rate (λ = 0.991). Models suggested that removal of the five highest risk turbines from the project, or institution of a curtailment regimen that shuts down at least these turbines at peak traffic times, could theoretically reduce impacts to manageable levels. However, in spite of the large quantities of high quality data used in our analyses, our collision risk model remains compromised by untested assumptions about pelican avoidance rates and uncertainties about the existing dynamics of the pelican population, and our findings are probably not reliable enough to ensure sustainable development.

Fragile X mental retardation protein knockdown in the developing Xenopus tadpole optic tectum results in enhanced feedforward inhibition and behavioral deficits.

PubMed

Truszkowski, Torrey L S; James, Eric J; Hasan, Mashfiq; Wishard, Tyler J; Liu, Zhenyu; Pratt, Kara G; Cline, Hollis T; Aizenman, Carlos D

2016-08-08

Fragile X Syndrome is the leading monogenetic cause of autism and most common form of intellectual disability. Previous studies have implicated changes in dendritic spine architecture as the primary result of loss of Fragile X Mental Retardation Protein (FMRP), but recent work has shown that neural proliferation is decreased and cell death is increased with either loss of FMRP or overexpression of FMRP. The purpose of this study was to investigate the effects of loss of FMRP on behavior and cellular activity. We knocked down FMRP expression using morpholino oligos in the optic tectum of Xenopus laevis tadpoles and performed a series of behavioral and electrophysiological assays. We investigated visually guided collision avoidance, schooling, and seizure propensity. Using single cell electrophysiology, we assessed intrinsic excitability and synaptic connectivity of tectal neurons. We found that FMRP knockdown results in decreased swimming speed, reduced schooling behavior and decreased seizure severity. In single cells, we found increased inhibition relative to excitation in response to sensory input. Our results indicate that the electrophysiological development of single cells in the absence of FMRP is largely unaffected despite the large neural proliferation defect. The changes in behavior are consistent with an increase in inhibition, which could be due to either changes in cell number or altered inhibitory drive, and indicate that FMRP can play a significant role in neural development much earlier than previously thought.

Exaggerated acquisition and resistance to extinction of avoidance behavior in treated heroin-dependent males

PubMed Central

Sheynin, Jony; Moustafa, Ahmed A.; Beck, Kevin D.; Servatius, Richard J.; Casbolt, Peter A.; Haber, Paul; Elsayed, Mahmoud; Hogarth, Lee; Myers, Catherine E.

2015-01-01

Objective Addiction is often conceptualized as a behavioral strategy for avoiding negative experiences. In rodents, opioid intake has been associated with abnormal acquisition and extinction of avoidance behavior. Here, we tested the hypothesis that these findings would generalize to human opioid-dependent subjects. Method Adults meeting DSM-IV criteria for heroin-dependence and treated with opioid medication (n=27), and healthy controls (n=26), were recruited between March–October 2013 and given a computer-based task to assess avoidance behavior. On this task, subjects controlled a spaceship and could either gain points by shooting an enemy spaceship, or hide in safe areas to avoid on-screen aversive events. Results While groups did not differ on escape responding (hiding) during the aversive event, heroin-dependent males (but not females) made more avoidance responses during a warning signal that predicted the aversive event (ANOVA, sex × group interaction, p=0.007). This group was also slower to extinguish the avoidance response when the aversive event no longer followed the warning signal (p=0.011). This behavioral pattern resulted in reduced opportunity to obtain reward without reducing risk of punishment. Results suggest that differences in avoidance behavior cannot be easily explained by impaired task performance or by exaggerated motor activity in male patients. Conclusion This study provides evidence for abnormal acquisition and extinction of avoidance behavior in opioid-dependent patients. Interestingly, data suggest abnormal avoidance is demonstrated only by male patients. Findings shed light on cognitive and behavioral manifestations of opioid addiction, and may facilitate development of therapeutic approaches to help affected individuals. PMID:27046310

Passive avoidance is linked to impaired fear extinction in humans

PubMed Central

Cornwell, Brian R.; Overstreet, Cassie; Krimsky, Marissa; Grillon, Christian

2013-01-01

Conventional wisdom dictates we must face our fears to conquer them. This idea is embodied in exposure-based treatments for anxiety disorders, where the intent of exposure is to reverse a history of avoidant behavior that is thought to fuel a patient’s irrational fears. We tested in humans the relationship between fear and avoidance by combining Pavlovian differential fear conditioning with a novel task for quantifying spontaneous passive avoidant behavior. During self-guided navigation in virtual reality following de novo fear conditioning, we observed participants keeping their distance from the feared object. At the individual level, passive avoidant behavior was highly associated with maladaptive fear expression (fear-potentiated startle) during late extinction training, indicating that extinction learning was impaired following a brief episode of avoidance. Avoidant behavior, however, was not related to initial acquired fear, raising doubt about a straightforward link between physiological fear and behavioral avoidance. We conclude that a deeper understanding of what motivates avoidance may offer a target for early intervention, before fears transition from the rational to the irrational. PMID:23427168

A unique tripartite collision tumor of the esophagus

PubMed Central

Schizas, Dimitrios; Michalinos, Adamantios; Alexandrou, Paraskevi; Moris, Demetrios; Baliou, Evangelia; Tsilimigras, Diamantis; Throupis, Theodore; Liakakos, Theodore

2017-01-01

Abstract Rationale: We report a unique case of a tripartite esophageal collision tumor consisting of three separate histologic types. Patients concerns: Therapeutic dilemmas on the proper treatment of those rare neoplasms remain unanswered considering both proper surgical therapy and adjuvant therapy. Diagnose: In this paper, we report a unique case of a patient with a tripartite esophageal collision tumor consisting of a small cell carcinoma, an adenocarcinoma of medium differentiation and a signet ring cell carcinoma. Diagnosis is difficult as clinical presentation of the patient was undistinguishable from other, commoner tumor types. Interventions: The patient's diagnostic and therapeutic course along with available data on the collisions tumor's biological behavior and treatment are briefly discussed. Outcomes: Esophagectomy is the best treatment options for these patients. Unique nature of this tumor demands aggresive oncologic treatment. Lessons: Collision tumors are rare neoplasms consisting of distinct cell populations developing in juxtaposition to one another without any areas of intermingling. Various cell types can be found. However, collision neoplasms of the esophagus combining adenomatous and neuroendocrine components are exceedingly rare, with only 5 cases described to date in the literature. Given their rarity, limited information is available on their tumorigenesis, biological behavior and clinical course. In general, these tumors are aggressive neoplasms and significantly affect patient treatment and prognosis. PMID:29245236

Bose-Einstein correlations in pp and PbPb collisions with ALICE at the LHC

ScienceCinema

Kisiel, Adam

2018-05-14

We report on the results of identical pion femtoscopy at the LHC. The Bose-Einstein correlation analysis was performed on the large-statistics ALICE p+p at sqrt{s}= 0.9 TeV and 7 TeV datasets collected during 2010 LHC running and the first Pb+Pb dataset at sqrt{s_NN}= 2.76 TeV. Detailed pion femtoscopy studies in heavy-ion collisions have shown that emission region sizes ("HBT radii") decrease with increasing pair momentum, which is understood as a manifestation of the collective behavior of matter. 3D radii were also found to universally scale with event multiplicity. In p+p collisions at 7 TeV one measures multiplicities which are comparable with those registered in peripheral AuAu and CuCu collisions at RHIC, so direct comparisons and tests of scaling laws are now possible. We show the results of double-differential 3D pion HBT analysis, as a function of multiplicity and pair momentum. The results for two collision energies are compared to results obtained in the heavy-ion collisions at similar multiplicity and p+p collisions at lower energy. We identify the relevant scaling variables for the femtoscopic radii and discuss the similarities and differences to results from heavy-ions. The observed trends give insight into the soft particle production mechanism in p+p collisions and suggest that a self-interacting collective system may be created in sufficiently high multiplicity events. First results for the central Pb+Pb collisions are also shown. A significant increase of the reaction zone volume and lifetime in comparison to RHIC is observed. Signatures of collective hydrodynamics-like behavior of the system are also apparent, and are compared to model predictions.

A simulator-based analysis of engineering treatments for right-hook bicycle crashes at signalized intersections.

PubMed

Warner, Jennifer; Hurwitz, David S; Monsere, Christopher M; Fleskes, Kayla

2017-07-01

A right-hook crash is a crash between a right-turning motor vehicle and an adjacent through-moving bicycle. At signalized intersections, these crashes can occur during any portion of the green interval when conflicting bicycles and vehicles are moving concurrently. The objective of this research was to evaluate the effectiveness of four types of engineering countermeasures - regulatory signage, intersection pavement marking, smaller curb radius, and protected intersection design - at modifying driver behaviors that are known contributing factors in these crashes. This research focused on right-hook crashes that occur during the latter stage of the circular green indication at signalized intersections with a shared right-turn and through lane. Changes in driver performance in response to treatments were measured in a high-fidelity driving simulator. Twenty-eight participants each completed 22 right-turn maneuvers. A partially counterbalanced experimental design exposed drivers to critical scenarios, which had been determined in a previous experiment. For each turn, driver performance measures, including visual attention, crash avoidance, and potential crash severity, were collected. A total of 75 incidents (47 near-collisions and 28 collisions) were observed during the 616 right turns. All treatments had some positive effect on measured driver performance with respect to the right-turn vehicle conflicts. Further work is required to map the magnitude of these changes in driver performance to crash-based outcomes. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Teacher-Report Measure of Children's Task-Avoidant Behavior: A Validation Study of the Behavioral Strategy Rating Scale

ERIC Educational Resources Information Center

Zhang, Xiao; Nurmi, Jari-Erik; Kiuru, Noona; Lerkkanen, Marja-Kristiina; Aunola, Kaisa

2011-01-01

This study aims to validate a teacher-report measure of children's task-avoidant behavior, namely the Behavioral Strategy Rating Scale (BSRS), in a sample of 352 Finnish children. In each of the four waves from Kindergarten to Grade 2, teachers rated children's task-avoidant behavior using the BSRS, children completed reading and mathematics…

Assessing vulnerability of marine bird populations to offshore wind farms.

PubMed

Furness, Robert W; Wade, Helen M; Masden, Elizabeth A

2013-04-15

Offshore wind farms may affect bird populations through collision mortality and displacement. Given the pressures to develop offshore wind farms, there is an urgent need to assess population-level impacts on protected marine birds. Here we refine an approach to assess aspects of their ecology that influence population vulnerability to wind farm impacts, also taking into account the conservation importance of each species. Flight height appears to be a key factor influencing collision mortality risk but improved data on flight heights of marine birds are needed. Collision index calculations identify populations of gulls, white-tailed eagles, northern gannets and skuas as of particularly high concern in Scottish waters. Displacement index calculations identify populations of divers and common scoters as most vulnerable to population-level impacts of displacement, but these are likely to be less evident than impacts of collision mortality. The collision and displacement indices developed here for Scottish marine bird populations could be applied to populations elsewhere, and this approach will help in identifying likely impacts of future offshore wind farms on marine birds and prioritising monitoring programmes, at least until data on macro-avoidance rates become available. Copyright © 2013 Elsevier Ltd. All rights reserved.

14 CFR Appendix D to Part 25 - Appendix D to Part 25

Code of Federal Regulations, 2013 CFR

2013-01-01

... considered: (1) Flight path control. (2) Collision avoidance. (3) Navigation. (4) Communications. (5... flight, power, and equipment controls, including emergency fuel shutoff valves, electrical controls... crew action to guard against loss of hydraulic or electric power to flight controls or to other...

Information Measures for Statistical Orbit Determination

ERIC Educational Resources Information Center

Mashiku, Alinda K.

2013-01-01

The current Situational Space Awareness (SSA) is faced with a huge task of tracking the increasing number of space objects. The tracking of space objects requires frequent and accurate monitoring for orbit maintenance and collision avoidance using methods for statistical orbit determination. Statistical orbit determination enables us to obtain…

14 CFR Appendix A to Part 141 - Recreational Pilot Certification Course

Code of Federal Regulations, 2013 CFR

2013-01-01

... navigation using pilotage with the aid of a magnetic compass; (e) Recognition of critical weather situations... the aircraft category and class for which the course applies: (a) Applicable Federal Aviation... reports and forecasts; (f) Safe and efficient operation of aircraft, including collision avoidance, and...

Driver Performance and IVHS Collision Avoidance Systems: A Search for Design-Relevant Measurement Protocols

DOT National Transportation Integrated Search

1993-04-14

In 2005, the US Department of Transportation (DOT) initiated a program to develop and test a 5.9GHzbased Vehicle Infrastructure Integration (VII) proof of concept (POC). The POC was implemented in the northwest suburbs of Detroit, Michigan. This r...