40 CFR 98.193 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (General Stationary Fuel Combustion Sources) the combustion CO2 emissions from each lime kiln according to... must calculate and report the annual process CO2 emissions from all lime kilns combined using the... combustion CO2 emissions from all lime kilns by operating and maintaining a CEMS to measure CO2 emissions...

RESEARCH ON EMISSIONS AND MITIGATION OF POP'S FROM COMBUSTION SOURCES

EPA Science Inventory

Chapter summarizes EPA's research on emissions and control of persistent organic pollutants (POPS) from combustion sources, with emphasis on source characterization and measurement, formation and destruction mechanisms, formation prevention, and flue gas cleaning. Laboratory exp...

40 CFR 98.83 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (General Stationary Fuel Combustion Sources) the combustion CO2 emissions from the kiln according to the... calculate and report the annual process CO2 emissions from each kiln using the procedure in paragraphs (a... combustion CO2 emissions by operating and maintaining a CEMS to measure CO2 emissions according to the Tier 4...

40 CFR 98.83 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (General Stationary Fuel Combustion Sources) the combustion CO2 emissions from the kiln according to the... calculate and report the annual process CO2 emissions from each kiln using the procedure in paragraphs (a... combustion CO2 emissions by operating and maintaining a CEMS to measure CO2 emissions according to the Tier 4...

40 CFR 98.83 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (General Stationary Fuel Combustion Sources) the combustion CO2 emissions from the kiln according to the... calculate and report the annual process CO2 emissions from each kiln using the procedure in paragraphs (a... combustion CO2 emissions by operating and maintaining a CEMS to measure CO2 emissions according to the Tier 4...

AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

EPA Science Inventory

The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

Impact of various operating modes on performance and emission parameters of small heat source

NASA Astrophysics Data System (ADS)

Vician, Peter; Holubčík, Michal; Palacka, Matej; Jandačka, Jozef

2016-06-01

Thesis deals with the measurement of performance and emission parameters of small heat source for combustion of biomass in each of its operating modes. As the heat source was used pellet boiler with an output of 18 kW. The work includes design of experimental device for measuring the impact of changes in air supply and method for controlling the power and emission parameters of heat sources for combustion of woody biomass. The work describes the main factors that affect the combustion process and analyze the measurements of emissions at the heat source. The results of experiment demonstrate the values of performance and emissions parameters for the different operating modes of the boiler, which serve as a decisive factor in choosing the appropriate mode.

40 CFR 74.22 - Actual SO2 emissions rate.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Actual SO2 emissions rate. 74.22... (CONTINUED) SULFUR DIOXIDE OPT-INS Allowance Calculations for Combustion Sources § 74.22 Actual SO2 emissions... actual SO2 emissions rate shall be 1985. (2) For combustion sources that commenced operation after...

40 CFR 98.143 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Stationary Fuel Combustion Sources) the combustion CO2 emissions in the glass furnace according to the... calculate and report the annual process CO2 emissions from each continuous glass melting furnace using the... subpart the combined process and combustion CO2 emissions by operating and maintaining a CEMS to measure...

Control of mercury emissions from stationary coal combustion sources in China: Current status and recommendations.

PubMed

Hu, Yuanan; Cheng, Hefa

2016-11-01

Coal burning in power plants and industrial boilers is the largest combustion source of mercury emissions in China. Together, power plants and industrial boilers emit around 250 tonnes of mercury each year, or around half of atmospheric mercury emissions from anthropogenic sources in the country. Power plants in China are generally equipped with multi-pollutant control technologies, which offer the co-benefit of mercury removal, while mercury-specific control technologies have been installed in some facilities. In contrast, most industrial boilers have only basic or no flue gas cleaning. A combination of measures, including energy conservation, coal switching and blending, reducing the mercury contents of coals through washing, combustion controls, and flue gas cleaning, can be used to reduce mercury emissions from these stationary combustion sources. More stringent emission standards for the major air pollutants from coal-fired power plants and industrial boiler, along with standards for the previously unregulated mercury, were implemented recently, which is expected to bring significant reduction in their mercury emissions through the necessary upgrades of multi-pollutant and mercury-specific control technologies. Meanwhile, strong monitoring capacity and strict enforcement are necessary to ensure that the combustion sources operate in compliance with the new emission standards and achieve significant reduction in the emissions of mercury and other air pollutants. Copyright © 2016 Elsevier Ltd. All rights reserved.

Source diagnostics of polycyclic aromatic hydrocarbons in urban road runoff, dust, rain and canopy throughfall.

PubMed

Zhang, Wei; Zhang, Shucai; Wan, Chao; Yue, Dapan; Ye, Youbin; Wang, Xuejun

2008-06-01

Diagnostic ratios and multivariate analysis were utilized to apportion polycyclic aromatic hydrocarbon (PAH) sources for road runoff, road dust, rain and canopy throughfall based on samples collected in an urban area of Beijing, China. Three sampling sites representing vehicle lane, bicycle lane and branch road were selected. For road runoff and road dust, vehicular emission and coal combustion were identified as major sources, and the source contributions varied among the sampling sites. For rain, three principal components were apportioned representing coal/oil combustion (54%), vehicular emission (34%) and coking (12%). For canopy throughfall, vehicular emission (56%), coal combustion (30%) and oil combustion (14%) were identified as major sources. Overall, the PAH's source for road runoff mainly reflected that for road dust. Despite site-specific sources, the findings at the study area provided a general picture of PAHs sources for the road runoff system in urban area of Beijing.

40 CFR 49.129 - Rule for limiting emissions of sulfur dioxide.

Code of Federal Regulations, 2010 CFR

2010-07-01

... emissions from a combustion source stack must not exceed an average of 500 parts per million by volume, on a..., air pollution source, ambient air, British thermal unit (Btu), coal, combustion source, continuous..., incinerator, marine vessel, mobile sources, motor vehicle, nonroad engine, nonroad vehicle, open burning...

40 CFR 49.129 - Rule for limiting emissions of sulfur dioxide.

Code of Federal Regulations, 2011 CFR

2011-07-01

... emissions from a combustion source stack must not exceed an average of 500 parts per million by volume, on a..., air pollution source, ambient air, British thermal unit (Btu), coal, combustion source, continuous..., incinerator, marine vessel, mobile sources, motor vehicle, nonroad engine, nonroad vehicle, open burning...

Using Sediment Records to Reconstruct Historical Inputs Combustion-Derived Contaminants to Urban Airsheds/Watersheds: A Case Study From the Puget Sound

NASA Astrophysics Data System (ADS)

Louchouarn, P. P.; Kuo, L.; Brandenberger, J.; Marcantonio, F.; Wade, T. L.; Crecelius, E.; Gobeil, C.

2008-12-01

Urban centers are major sources of combustion-derived particulate matter (e.g. black carbon (BC), polycyclic aromatic hydrocarbons (PAH), anhydrosugars) and volatile organic compounds to the atmosphere. Evidence is mounting that atmospheric emissions from combustion sources remain major contributors to air pollution of urban systems. For example, recent historical reconstructions of depositional fluxes for pyrogenic PAHs close to urban systems have shown an unanticipated reversal in the trends of decreasing emissions initiated during the mid-20th Century. Here we compare a series of historical reconstructions of combustion emission in urban and rural airsheds over the last century using sedimentary records. A complex suite of combustion proxies (BC, PAHs, anhydrosugars, stable lead concentrations and isotope signatures) assisted in elucidating major changes in the type of atmospheric aerosols originating from specific processes (i.e. biomass burning vs. fossil fuel combustion) or fuel sources (wood vs. coal vs. oil). In all studied locations, coal continues to be a major source of combustion-derived aerosols since the early 20th Century. Recently, however, oil and biomass combustion have become substantial additional sources of atmospheric contamination. In the Puget Sound basin, along the Pacific Northwest region of the U.S., rural locations not impacted by direct point sources of contamination have helped assess the influence of catalytic converters on concentrations of oil-derived PAH and lead inputs since the early 1970s. Although atmospheric deposition of lead has continued to drop since the introduction of catalytic converters and ban on leaded gasoline, PAH inputs have "rebounded" in the last decade. A similar steady and recent rise in PAH accumulations in urban systems has been ascribed to continued urban sprawl and increasing vehicular traffic. In the U.S., automotive emissions, whether from gasoline or diesel combustion, are becoming a major source of combustion-derived PM and BC to the atmosphere and have started to replace coal as the major source in some surficial reservoirs. This increased urban influence of gasoline and diesel combustion on BC emissions was also observed in Europe both from model estimates as well as from measured fluxes in recent lake sediments.

Quantifying Molecular Hydrogen Emissions and an Industrial Leakage Rate for the South Coast Air Basin of California

NASA Astrophysics Data System (ADS)

Irish, M. C.; Schroeder, J.; Beyersdorf, A. J.; Blake, D. R.

2015-12-01

The poorly understood atmospheric budget and distribution of molecular hydrogen (H2) have invited further research since the discovery that emissions from a hydrogen-based economy could have negative impacts on the global climate system and stratospheric ozone. The burgeoning fuel cell electric vehicle industry in the South Coast Air Basin of California (SoCAB) presents an opportunity to observe and constrain urban anthropogenic H2 emissions. This work presents the first H2 emissions estimate for the SoCAB and calculates an upper limit for the current rate of leakage from production and distribution infrastructure within the region. A top-down method utilized whole air samples collected during the Student Airborne Research Program (SARP) onboard the NASA DC-8 research aircraft from 23-25 June 2015 to estimate H2 emissions from combustion and non-combustion sources. H2:carbon monoxide (CO) and H2:carbon dioxide ratios from airborne observations were compared with experimentally established ratios from pure combustion source ratios and scaled with the well-constrained CO emissions inventory to yield H2 emissions of 24.9 ± 3.6 Gg a-1 (1σ) from combustion engines and 8.2 ± 4.7 Gg a-1 from non-combustion sources. Total daily production of H2 in the SoCAB was compared with the top-down results to estimate an upper limit leakage rate (5%) where all emissions not accounted for by incomplete combustion in engines were assumed to be emitted from H2 infrastructure. For bottom-up validation, the NOAA Hybrid Single Particle Lagrangian Integrated Trajectory dispersion model was run iteratively with all known stationary sources in attempt to constrain emissions. While this investigation determined that H2 emissions from non-combustion sources in the SoCAB are likely significant, more in-depth analysis is required to better predict the atmospheric implications of a hydrogen economy.

Unspeciated organic emissions from combustion sources and their influence on the secondary organic aerosol budget in the United States

PubMed Central

Jathar, Shantanu H.; Gordon, Timothy D.; Hennigan, Christopher J.; Pye, Havala O. T.; Pouliot, George; Adams, Peter J.; Donahue, Neil M.; Robinson, Allen L.

2014-01-01

Secondary organic aerosol (SOA) formed from the atmospheric oxidation of nonmethane organic gases (NMOG) is a major contributor to atmospheric aerosol mass. Emissions and smog chamber experiments were performed to investigate SOA formation from gasoline vehicles, diesel vehicles, and biomass burning. About 10–20% of NMOG emissions from these major combustion sources are not routinely speciated and therefore are currently misclassified in emission inventories and chemical transport models. The smog chamber data demonstrate that this misclassification biases model predictions of SOA production low because the unspeciated NMOG produce more SOA per unit mass than the speciated NMOG. We present new source-specific SOA yield parameterizations for these unspeciated emissions. These parameterizations and associated source profiles are designed for implementation in chemical transport models. Box model calculations using these new parameterizations predict that NMOG emissions from the top six combustion sources form 0.7 Tg y−1 of first-generation SOA in the United States, almost 90% of which is from biomass burning and gasoline vehicles. About 85% of this SOA comes from unspeciated NMOG, demonstrating that chemical transport models need improved treatment of combustion emissions to accurately predict ambient SOA concentrations. PMID:25002466

Assessing the long-range transport of PAH to a sub-Arctic site using positive matrix factorization and potential source contribution function

NASA Astrophysics Data System (ADS)

Sofowote, Uwayemi M.; Hung, Hayley; Rastogi, Ankit K.; Westgate, John N.; Deluca, Patrick F.; Su, Yushan; McCarry, Brian E.

2011-02-01

Gas-phase and particle-phase atmospheric samples collected in a sparsely populated sub-Arctic environment in the Yukon Territory, Canada were analyzed for a wide range of organic pollutants including polycyclic aromatic hydrocarbons (PAH). Receptor modeling using positive matrix factorization (PMF) was applied to a PAH data set from samples collected between August 2007 and December 2008 to afford four factors. These factors were designated as fossil fuel combustion emissions, particle-phase wood combustion emissions, gas-phase wood combustion emissions, and unburned petroleum/petrogenic emissions. The multiple linear regression-derived average contributions of these factors to the total PAH concentrations were 14% for fossil fuel combustion, 6% for particle-phase wood combustion emissions, 46% for gas-phase wood combustion emissions and 34% for petrogenic emissions. When the total PAH concentrations (defined as the sum of twenty-two PAH) and the PMF-modeled PAH concentrations set were compared, the correlation was excellent ( R2 = 0.97). Ten-day back trajectories starting at four different heights were used in a potential source contribution function analysis (PSCF) to assess the potential source regions of these PAH factors. Mapping the computed PSCF values for the four PMF factors revealed different source regions in the northern hemisphere for each PMF factor. Atmospheric transport of PAH occurred from both relatively short and long distances with both continental (North American) and trans-oceanic (Asian) sources contributing significantly to the total PAH. This study provides evidence of the transport of fossil fuel and wood combustion emissions from Asia, continental North America and northern Europe to sub-Arctic Canada (and by extension to the Canadian Arctic) primarily during cooler (fall-winter) months. This study demonstrates for the first time that the combined PMF-PSCF methodology can be used to identify geographically-disperse PAH source contributors on a hemispherical scale.

Health impacts of anthropogenic biomass burning in the developed world.

PubMed

Sigsgaard, Torben; Forsberg, Bertil; Annesi-Maesano, Isabella; Blomberg, Anders; Bølling, Anette; Boman, Christoffer; Bønløkke, Jakob; Brauer, Michael; Bruce, Nigel; Héroux, Marie-Eve; Hirvonen, Maija-Riitta; Kelly, Frank; Künzli, Nino; Lundbäck, Bo; Moshammer, Hanns; Noonan, Curtis; Pagels, Joachim; Sallsten, Gerd; Sculier, Jean-Paul; Brunekreef, Bert

2015-12-01

Climate change policies have stimulated a shift towards renewable energy sources such as biomass. The economic crisis of 2008 has also increased the practice of household biomass burning as it is often cheaper than using oil, gas or electricity for heating. As a result, household biomass combustion is becoming an important source of air pollutants in the European Union.This position paper discusses the contribution of biomass combustion to pollution levels in Europe, and the emerging evidence on the adverse health effects of biomass combustion products.Epidemiological studies in the developed world have documented associations between indoor and outdoor exposure to biomass combustion products and a range of adverse health effects. A conservative estimate of the current contribution of biomass smoke to premature mortality in Europe amounts to at least 40 000 deaths per year.We conclude that emissions from current biomass combustion products negatively affect respiratory and, possibly, cardiovascular health in Europe. Biomass combustion emissions, in contrast to emissions from most other sources of air pollution, are increasing. More needs to be done to further document the health effects of biomass combustion in Europe, and to reduce emissions of harmful biomass combustion products to protect public health. Copyright ©ERS 2015.

40 CFR Table 4 to Subpart Bbbb of... - Model Rule-Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a

Code of Federal Regulations, 2011 CFR

2011-07-01

... Existing Small Municipal Waste Combustion Unit a 4 Table 4 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a For...

40 CFR Table 2 to Subpart Bbbb of... - Model Rule-Class I Emission Limits for Existing Small Municipal Waste Combustion Units a

Code of Federal Regulations, 2014 CFR

2014-07-01

... Existing Small Municipal Waste Combustion Units a 2 Table 2 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class I Emission Limits for Existing Small Municipal Waste Combustion Units a For...

40 CFR Table 4 to Subpart Bbbb of... - Model Rule-Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a

Code of Federal Regulations, 2014 CFR

2014-07-01

... Existing Small Municipal Waste Combustion Unit a 4 Table 4 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a For...

40 CFR Table 4 to Subpart Bbbb of... - Model Rule-Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a

Code of Federal Regulations, 2010 CFR

2010-07-01

... Existing Small Municipal Waste Combustion Unit a 4 Table 4 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a For...

40 CFR Table 2 to Subpart Bbbb of... - Model Rule-Class I Emission Limits for Existing Small Municipal Waste Combustion Units a

Code of Federal Regulations, 2012 CFR

2012-07-01

... Existing Small Municipal Waste Combustion Units a 2 Table 2 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class I Emission Limits for Existing Small Municipal Waste Combustion Units a For...

40 CFR Table 2 to Subpart Bbbb of... - Model Rule-Class I Emission Limits for Existing Small Municipal Waste Combustion Units a

Code of Federal Regulations, 2013 CFR

2013-07-01

... Existing Small Municipal Waste Combustion Units a 2 Table 2 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class I Emission Limits for Existing Small Municipal Waste Combustion Units a For...

40 CFR Table 2 to Subpart Bbbb of... - Model Rule-Class I Emission Limits for Existing Small Municipal Waste Combustion Units a

Code of Federal Regulations, 2010 CFR

2010-07-01

... Existing Small Municipal Waste Combustion Units a 2 Table 2 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class I Emission Limits for Existing Small Municipal Waste Combustion Units a For...

40 CFR Table 2 to Subpart Bbbb of... - Model Rule-Class I Emission Limits for Existing Small Municipal Waste Combustion Units a

Code of Federal Regulations, 2011 CFR

2011-07-01

... Existing Small Municipal Waste Combustion Units a 2 Table 2 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class I Emission Limits for Existing Small Municipal Waste Combustion Units a For...

40 CFR Table 4 to Subpart Bbbb of... - Model Rule-Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a

Code of Federal Regulations, 2012 CFR

2012-07-01

... Existing Small Municipal Waste Combustion Unit a 4 Table 4 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a For...

40 CFR Table 4 to Subpart Bbbb of... - Model Rule-Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a

Code of Federal Regulations, 2013 CFR

2013-07-01

... Existing Small Municipal Waste Combustion Unit a 4 Table 4 to Subpart BBBB of Part 60 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... Part 60—Model Rule—Class II Emission Limits for Existing Small Municipal Waste Combustion Unit a For...

Source apportionment of ambient volatile organic compounds in the Pearl River Delta, China: Part II

NASA Astrophysics Data System (ADS)

Liu, Ying; Shao, Min; Lu, Sihua; Chang, Chih-Chung; Wang, Jia-Lin; Fu, Linlin

The chemical mass balance receptor model was applied to the source apportionment of 58 hydrocarbons measured at seven sites in a field campaign that examined regional air quality in the Pearl River Delta (PRD) region in the fall of 2004. A total of 12 volatile organic compound (VOC) emission sources were considered, including gasoline- and diesel-powered vehicle exhausts, headspace vapors of gasoline and diesel fuel, vehicle evaporative emissions, liquid petroleum gas (LPG) leakage, paint vapors, asphalt emissions from paved roads, biomass combustion, coal combustion, the chemical industry, and petroleum refineries. Vehicle exhaust was the largest source of VOCs, contributing to >50% of ambient VOCs at the three urban sites (Guangzhou, Foshan, and Zhongshan). LPG leakage played an important role, representing 8-16% of emissions at most sites in the PRD. Solvent usage was the biggest emitter of VOCs at Dongguan, an industrial site, contributing 33% of ambient VOCs. Similarly, at Xinken, a non-urban site, the evaporation of solvents and coatings was the largest emission source, accounting for 31% of emissions, probably because it was downwind of Dongguan. Local biomass combustion was a noticeable source of VOCs at Xinken; although its contribution was estimated at 14.3%, biomass combustion was the third largest VOC source at this site.

Investigation of black and brown carbon multiple-wavelength-dependent light absorption from biomass and fossil fuel combustion source emissions

Treesearch

Michael R. Olson; Mercedes Victoria Garcia; Michael A. Robinson; Paul Van Rooy; Mark A. Dietenberger; Michael Bergin; James Jay Schauer

2015-01-01

Quantification of the black carbon (BC) and brown carbon (BrC) components of source emissions is critical to understanding the impact combustion aerosols have on atmospheric light absorption. Multiple-wavelength absorption was measured from fuels including wood, agricultural biomass, coals, plant matter, and petroleum distillates in controlled combustion settings....

HETEROGENEOUS SOOT NANOSTRUCTURE IN ATMOSPHERIC AND COMBUSTION SOURCE AEROSOLS

EPA Science Inventory

Microscopic images of soot emissions from wildfire and a wide range of anthropogenic combustion sources show that the nanostructures of individual particles in these emissions are predominantly heterogeneous, decidedly influenced by the fuel composition and by the particular comb...

Updating the conceptual model for fine particle mass emissions from combustion systems.

PubMed

Robinson, Allen L; Grieshop, Andrew P; Donahue, Neil M; Hunt, Sherri W

2010-10-01

Atmospheric transformations determine the contribution of emissions from combustion systems to fine particulate matter (PM) mass. For example, combustion systems emit vapors that condense onto existing particles or form new particles as the emissions are cooled and diluted. Upon entering the atmosphere, emissions are exposed to atmospheric oxidants and sunlight, which causes them to evolve chemically and physically, generating secondary PM. This review discusses these transformations, focusing on organic PM. Organic PM emissions are semi-volatile at atmospheric conditions and thus their partitioning varies continuously with changing temperature and concentration. Because organics contribute a large portion of the PM mass emitted by most combustion sources, these emissions cannot be represented using a traditional, static emission factor. Instead, knowledge of the volatility distribution of emissions is required to explicitly account for changes in gas-particle partitioning. This requires updating how PM emissions from combustion systems are measured and simulated from combustion systems. Secondary PM production often greatly exceeds the direct or primary PM emissions; therefore, secondary PM must be included in any assessment of the contribution of combustion systems to ambient PM concentrations. Low-volatility organic vapors emitted by combustion systems appear to be very important secondary PM precursors that are poorly accounted for in inventories and models. The review concludes by discussing the implications that the dynamic nature of these PM emissions have on source testing for emission inventory development and regulatory purposes. This discussion highlights important linkages between primary and secondary PM, which could lead to simplified certification test procedures while capturing the emission components that contribute most to atmospheric PM mass.

Updating the Conceptual Model for Fine Particle Mass Emissions from Combustion Systems Allen L. Robinson.

PubMed

Robinson, Allen L; Grieshop, Andrew P; Donahue, Neil M; Hunt, Sherri W

2010-10-01

Atmospheric transformations determine the contribution of emissions from combustion systems to fine particulate matter (PM) mass. For example, combustion systems emit vapors that condense onto existing particles or form new particles as the emissions are cooled and diluted. Upon entering the atmosphere, emissions are exposed to atmospheric oxidants and sunlight, which causes them to evolve chemically and physically, generating secondary PM. This review discusses these transformations, focusing on organic PM. Organic PM emissions are semi -volatile at atmospheric conditions and thus their partitioning varies continuously with changing temperature and concentration. Because organics contribute a large portion of the PM mass emitted by most combustion sources, these emissions cannot be represented using a traditional, static emission factor. Instead, knowledge of the volatility distribution of emissions is required to explicitly account for changes in gas-particle partitioning. This requires updating how PM emissions from combustion systems are measured and simulated from combustion systems. Secondary PM production often greatly exceeds the direct or primary PM emissions; therefore, secondary PM must be included in any assessment of the contribution of combustion systems to ambient PM concentrations. Low-volatility organic vapors emitted by combustion systems appear to be very important secondary PM precursors that are poorly accounted for in inventories and models. The review concludes by discussing the implications that the dynamic nature of these PM emissions have on source testing for emission inventory development and regulatory purposes. This discussion highlights important linkages between primary and secondary PM, which could lead to simplified certification test procedures while capturing the emission components that contribute most to atmospheric PM mass.

40 CFR 74.23 - 1985 Allowable SO2 emissions rate.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false 1985 Allowable SO2 emissions rate. 74... (CONTINUED) SULFUR DIOXIDE OPT-INS Allowance Calculations for Combustion Sources § 74.23 1985 Allowable SO2... data: (i) Allowable SO2 emissions rate of the combustion source expressed in lbs/mmBtu as defined under...

Considering the future of anthropogenic gas-phase organic compound emissions and the increasing influence of non-combustion sources on urban air quality

NASA Astrophysics Data System (ADS)

Khare, Peeyush; Gentner, Drew R.

2018-04-01

Decades of policy in developed regions has successfully reduced total anthropogenic emissions of gas-phase organic compounds, especially volatile organic compounds (VOCs), with an intentional, sustained focus on motor vehicles and other combustion-related sources. We examine potential secondary organic aerosol (SOA) and ozone formation in our case study megacity (Los Angeles) and demonstrate that non-combustion-related sources now contribute a major fraction of SOA and ozone precursors. Thus, they warrant greater attention beyond indoor environments to resolve large uncertainties in their emissions, oxidation chemistry, and outdoor air quality impacts in cities worldwide. We constrain the magnitude and chemical composition of emissions via several bottom-up approaches using chemical analyses of products, emissions inventory assessments, theoretical calculations of emission timescales, and a survey of consumer product material safety datasheets. We demonstrate that the chemical composition of emissions from consumer products as well as commercial and industrial products, processes, and materials is diverse across and within source subcategories. This leads to wide ranges of SOA and ozone formation potentials that rival other prominent sources, such as motor vehicles. With emission timescales from minutes to years, emission rates and source profiles need to be included, updated, and/or validated in emissions inventories with expected regional and national variability. In particular, intermediate-volatility and semi-volatile organic compounds (IVOCs and SVOCs) are key precursors to SOA, but are excluded or poorly represented in emissions inventories and exempt from emissions targets. We present an expanded framework for classifying VOC, IVOC, and SVOC emissions from this diverse array of sources that emphasizes a life cycle approach over longer timescales and three emission pathways that extend beyond the short-term evaporation of VOCs: (1) solvent evaporation, (2) solute off-gassing, and (3) volatilization of degradation by-products. Furthermore, we find that ambient SOA formed from these non-combustion-related emissions could be misattributed to fossil fuel combustion due to the isotopic signature of their petroleum-based feedstocks.

40 CFR 98.293 - Calculating GHG emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... subpart C of this part (General Stationary Fuel Combustion Sources) the combustion CO2, CH4, and N2O... must calculate and report the annual process CO2 emissions from each soda ash manufacturing line using... report under this subpart the combined process and combustion CO2 emissions by operating and maintaining...

40 CFR 98.183 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Stationary Fuel Combustion Sources). (2) Calculate and report process and combustion CO2 emissions separately... calculate and report the annual process CO2 emissions from each smelting furnace using the procedure in... § 98.33(b)(4)(ii) or (b)(4)(iii), you must calculate and report combined process and combustion CO2...

40 CFR 98.293 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... subpart C of this part (General Stationary Fuel Combustion Sources) the combustion CO2, CH4, and N2O... must calculate and report the annual process CO2 emissions from each soda ash manufacturing line using... report under this subpart the combined process and combustion CO2 emissions by operating and maintaining...

40 CFR 98.293 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... subpart C of this part (General Stationary Fuel Combustion Sources) the combustion CO2, CH4, and N2O... must calculate and report the annual process CO2 emissions from each soda ash manufacturing line using... report under this subpart the combined process and combustion CO2 emissions by operating and maintaining...

40 CFR 98.183 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Stationary Fuel Combustion Sources). (2) Calculate and report process and combustion CO2 emissions separately... calculate and report the annual process CO2 emissions from each smelting furnace using the procedure in... § 98.33(b)(4)(ii) or (b)(4)(iii), you must calculate and report combined process and combustion CO2...

40 CFR 98.183 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Stationary Fuel Combustion Sources). (2) Calculate and report process and combustion CO2 emissions separately... calculate and report the annual process CO2 emissions from each smelting furnace using the procedure in... § 98.33(b)(4)(ii) or (b)(4)(iii), you must calculate and report combined process and combustion CO2...

40 CFR 98.183 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Stationary Fuel Combustion Sources). (2) Calculate and report process and combustion CO2 emissions separately... calculate and report the annual process CO2 emissions from each smelting furnace using the procedure in... § 98.33(b)(4)(ii) or (b)(4)(iii), you must calculate and report combined process and combustion CO2...

40 CFR 98.293 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... subpart C of this part (General Stationary Fuel Combustion Sources) the combustion CO2, CH4, and N2O... must calculate and report the annual process CO2 emissions from each soda ash manufacturing line using... report under this subpart the combined process and combustion CO2 emissions by operating and maintaining...

40 CFR 98.293 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... subpart C of this part (General Stationary Fuel Combustion Sources) the combustion CO2, CH4, and N2O... must calculate and report the annual process CO2 emissions from each soda ash manufacturing line using... report under this subpart the combined process and combustion CO2 emissions by operating and maintaining...

Estimating State-Specific Contributions to PM2.5- and O3-Related Health Burden from Residential Combustion and Electricity Generating Unit Emissions in the United States.

PubMed

Penn, Stefani L; Arunachalam, Saravanan; Woody, Matthew; Heiger-Bernays, Wendy; Tripodis, Yorghos; Levy, Jonathan I

2017-03-01

Residential combustion (RC) and electricity generating unit (EGU) emissions adversely impact air quality and human health by increasing ambient concentrations of fine particulate matter (PM 2.5 ) and ozone (O 3 ). Studies to date have not isolated contributing emissions by state of origin (source-state), which is necessary for policy makers to determine efficient strategies to decrease health impacts. In this study, we aimed to estimate health impacts (premature mortalities) attributable to PM 2.5 and O 3 from RC and EGU emissions by precursor species, source sector, and source-state in the continental United States for 2005. We used the Community Multiscale Air Quality model employing the decoupled direct method to quantify changes in air quality and epidemiological evidence to determine concentration-response functions to calculate associated health impacts. We estimated 21,000 premature mortalities per year from EGU emissions, driven by sulfur dioxide emissions forming PM 2.5 . More than half of EGU health impacts are attributable to emissions from eight states with significant coal combustion and large downwind populations. We estimate 10,000 premature mortalities per year from RC emissions, driven by primary PM 2.5 emissions. States with large populations and significant residential wood combustion dominate RC health impacts. Annual mortality risk per thousand tons of precursor emissions (health damage functions) varied significantly across source-states for both source sectors and all precursor pollutants. Our findings reinforce the importance of pollutant-specific, location-specific, and source-specific models of health impacts in design of health-risk minimizing emissions control policies. Citation: Penn SL, Arunachalam S, Woody M, Heiger-Bernays W, Tripodis Y, Levy JI. 2017. Estimating state-specific contributions to PM 2.5 - and O 3 -related health burden from residential combustion and electricity generating unit emissions in the United States. Environ Health Perspect 125:324-332; http://dx.doi.org/10.1289/EHP550.

40 CFR 74.60 - Monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Monitoring requirements. 74.60 Section...) SULFUR DIOXIDE OPT-INS Monitoring Emissions: Combustion Sources § 74.60 Monitoring requirements. (a) Monitoring requirements for combustion sources. The owner or operator of each combustion source shall meet...

Ultra-lean combustion at high inlet temperatures

NASA Technical Reports Server (NTRS)

Anderson, D. N.

1981-01-01

Combustion at inlet air temperatures of 1100 to 1250 K was studied for application to advanced automotive gas turbine engines. Combustion was initiated by the hot environment, and therefore no external ignition source was used. Combustion was stabilized without a flameholder. The tests were performed in a 12 cm diameter test section at a pressure of 2.5 x 10 to the 5th power Pa, with reference velocities of 32 to 60 m/sec and at maximum combustion temperatures of 1350 to 1850 K. Number 2 diesel fuel was injected by means of a multiple source fuel injector. Unburned hydrocarbons emissions were negligible for all test conditions. Nitrogen oxides emissions were less than 1.9 g NO2/kg fuel for combustion temperatures below 1680 K. Carbon monoxide emissions were less than 16 g CO/kg fuel for combustion temperatures greater than 1600 K, inlet air temperatures higher than 1150 K, and residence times greater than 4.3 microseconds.

EMISSIONS AND COST ESTIMATES FOR GLOBALLY SIGNIFICANT ANTHROPOGENIC COMBUSTION SOURCES OF NOX, N2O, CH4, CO AND CO2

EPA Science Inventory

The report discusses the development of emission factors for CO2, CO, CH4, NOx, and N2O for about 80 globally significant combustion sources in seven source categories: utility, industrial, fuel production, transportation, residential, commercial, and kilns/ovens/dryers. ecause o...

Semivolatile POA and parameterized total combustion SOA in CMAQv5.2: impacts on source strength and partitioning

EPA Science Inventory

Mounting evidence from field and laboratory observations coupled with atmospheric model analyses shows that primary combustion emissions of organic compounds dynamically partition between the vapor and particulate phases, especially as near-source emissions dilute and cool to amb...

NATIONAL INVENTORIES FOR AREA SOURCE FUEL COMBUSTION AND GASOLINE MARKETING IN 1999

EPA Science Inventory

The product will be a set of estimates of county-level 1999 emissions of all relevant air pollutants from gasoline marketing and from the combustion of fuel by "area" sources, i.e., those too small be be required to report their emissions individually.

Regional Influence of Aerosol Emissions from Wildfires Driven by Combustion Efficiency: Insights from the BBOP Campaign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collier, Sonya; Zhou, Shan; Onasch, Timothy B.

Abstract Wildfires are important contributors to atmospheric aerosols and a large source of emissions that impact regional air quality and global climate. In this study, wildfire emissions in the Pacific Northwest region of the United States were characterized using real-time measurements near their sources using an aircraft, and farther downwind from a fixed ground site located at the Mt. Bachelor Observatory (~ 2700 m a.s.l.). The characteristics of aerosol emissions were found to depend strongly on the modified combustion efficiency (MCE), a qualitative index of the combustion processes of a fire. Organic aerosol emissions had negative correlations with MCE, whereasmore » the carbon oxidation state of organic aerosol increased with MCE. The relationships between the aerosol properties and MCE were consistent between fresher emissions (~1 hour old) and emissions sampled after atmospheric transport (6 - 45 hours), suggesting that organic aerosol mass loading and chemical properties were strongly influenced by combustion processes at the source and conserved to a significant extent during regional transport. These results suggest that MCE can be a useful metric for describing aerosol properties of regionally transported wildfire emissions and their impacts on regional air quality and global climate.« less

Composition and source apportionment of PM1 at urban site Kanpur in India using PMF coupled with CBPF

NASA Astrophysics Data System (ADS)

Rai, Pragati; Chakraborty, Abhishek; Mandariya, Anil Kumar; Gupta, Tarun

2016-09-01

This study addresses the three major questions: (1) what are the emission sources of PM1 which are affecting the study area; (2) where do these emission sources come from; and (3) is there any temporal variation in the emission sources. To address these issues, two advanced statistical methods are described in this paper. Identification of emission sources was performed by EPA PMF (v 5.0) and to understand the temporal variability, sampling was done for three winter seasons 2008-09, 2009-10 and 2011-12 within Kanpur city. To identify the possible source directions, Conditional Bivariate Probability function (CBPF) was used. The average PM1 concentration was higher in 2008-09 followed by 2011-12 and 2009-10 winter seasons. 2008-09 winter showed sources such as secondary sources mixed with power plant emission (42.8%), industrial emission (32.3%), coal combustion, brick kilns and vehicular emission (13.2%) and residual oil combustion and road dust (11.7%). The major contributors during winter season 2009-10 were secondary sources (33.1%), biomass burning (23.3%), heavy oil combustion (13%), vehicular emission mixed with crustal dust (11.3%), leather tanning industries (10.3%), industrial emission (4%), coal combustion and brick kilns (3.4%) and solid waste burning and incineration (1.5%) compared to secondary sources mixed with biomass burning (42.3%), industrial emission and crustal dust (35.1%) and vehicular emission and brick kilns (22.6%) during 2011-12 winter season. PMF model revealed that secondary sources were the main contributors for all the three winter seasons followed by biomass burning and power plant emission. The results of CBPF analysis agreed well with the locations of known local point sources., e.g. in the case of industrial emissions, the maximum probability was in the direction between NES direction where almost all the major industries are located in and around Kanpur while in the opposite direction the probability of biomass burning was high due to a rural area in NWS direction.

NEAR-REAL-TIME MEASUREMENT OF TRACE VOLATILE ORGANIC COMPOUNDS FROM COMBUSTION PROCESSES USING AN ON-LINE GAS CHROMATOGRAPH

EPA Science Inventory

The U.S. EPA's current regulatory approach for combustion and incineration sources emphasizes the use of real-time continuous emission monitors (CEMs) for particulate, Metals, and volatile, semivolatile, and of nonvolatile organic compounds to monitor source emissions. Currently...

Effects of fuel-injector design on ultra-lean combustion performance

NASA Technical Reports Server (NTRS)

Anderson, D. N.

1981-01-01

Emissions data were obtained for six fuel injector configurations tested with ultra lean combustion. Fuel injectors included three multiple source designs and three configurations using a single air assist injector. Only the multiple source fuel injectors provided acceptable emissions. Values of 16g CO/kg fuel, 1.9g HC/kg fuel, and 19.g NO2/kg fuel were obtained for the combustion temperature range of 1450 to 1700 K for both a high blockage 19 source injector and a low blockage 41 source injector. It was shown that high fuel injector pressure drop may not be required to achieve low emissions performance at high inlet air temperature when the fuel is well dispersed in the airstream.

Global Partitioning of NOx Sources Using Satellite Observations: Relative Roles of Fossil Fuel Combustion, Biomass Burning and Soil Emissions

NASA Technical Reports Server (NTRS)

Jaegle, Lyatt; Steinberger, Linda; Martin, Randall V.; Chance, Kelly

2005-01-01

This document contains the following abstract for the paper "Global partitioning of NOx sources using satellite observations: Relative roles of fossil fuel combustion, biomass burning and soil emissions." Satellite observations have been used to provide important new information about emissions of nitrogen oxides. Nitrogen oxides (NOx) are significant in atmospheric chemistry, having a role in ozone air pollution, acid deposition and climate change. We know that human activities have led to a three- to six-fold increase in NOx emissions since pre-industrial times, and that there are three main surface sources of NOx: fuel combustion, large-scale fires, and microbial soil processes. How each of these sources contributes to the total NOx emissions is subject to some doubt, however. The problem is that current NOx emission inventories rely on bottom-up approaches, compiling large quantities of statistical information from diverse sources such as fuel and land use, agricultural data, and estimates of burned areas. This results in inherently large uncertainties. To overcome this, Lyatt Jaegle and colleagues from the University of Washington, USA, used new satellite observations from the Global Ozone Monitoring Experiment (GOME) instrument. As the spatial and seasonal distribution of each of the sources of NOx can be clearly mapped from space, the team could provide independent topdown constraints on the individual strengths of NOx sources, and thus help resolve discrepancies in existing inventories. Jaegle's analysis of the satellite observations, presented at the recent Faraday Discussion on "Atmospheric Chemistry", shows that fuel combustion dominates emissions at northern mid-latitudes, while fires are a significant source in the Tropics. Additionally, she discovered a larger than expected role for soil emissions, especially over agricultural regions with heavy fertilizer use. Additional information is included in the original extended abstract.

40 CFR 63.6085 - Am I subject to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines What This... operate a stationary combustion turbine located at a major source of HAP emissions. (a) Stationary combustion turbine means all equipment, including but not limited to the turbine, the fuel, air, lubrication...

40 CFR 63.6085 - Am I subject to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines What This... operate a stationary combustion turbine located at a major source of HAP emissions. (a) Stationary combustion turbine means all equipment, including but not limited to the turbine, the fuel, air, lubrication...

40 CFR 63.6085 - Am I subject to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines What This... operate a stationary combustion turbine located at a major source of HAP emissions. (a) Stationary combustion turbine means all equipment, including but not limited to the turbine, the fuel, air, lubrication...

40 CFR 98.333 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the process CO2 emissions by... calculate and report the annual process CO2 emissions using the procedures specified in either paragraph (a... and combustion CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation...

40 CFR 98.333 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the process CO2 emissions by... calculate and report the annual process CO2 emissions using the procedures specified in either paragraph (a... and combustion CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation...

40 CFR 98.333 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the process CO2 emissions by... calculate and report the annual process CO2 emissions using the procedures specified in either paragraph (a... and combustion CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation...

Estimating State-Specific Contributions to PM2.5- and O3-Related Health Burden from Residential Combustion and Electricity Generating Unit Emissions in the United States

PubMed Central

Penn, Stefani L.; Arunachalam, Saravanan; Woody, Matthew; Heiger-Bernays, Wendy; Tripodis, Yorghos; Levy, Jonathan I.

2016-01-01

Background: Residential combustion (RC) and electricity generating unit (EGU) emissions adversely impact air quality and human health by increasing ambient concentrations of fine particulate matter (PM2.5) and ozone (O3). Studies to date have not isolated contributing emissions by state of origin (source-state), which is necessary for policy makers to determine efficient strategies to decrease health impacts. Objectives: In this study, we aimed to estimate health impacts (premature mortalities) attributable to PM2.5 and O3 from RC and EGU emissions by precursor species, source sector, and source-state in the continental United States for 2005. Methods: We used the Community Multiscale Air Quality model employing the decoupled direct method to quantify changes in air quality and epidemiological evidence to determine concentration–response functions to calculate associated health impacts. Results: We estimated 21,000 premature mortalities per year from EGU emissions, driven by sulfur dioxide emissions forming PM2.5. More than half of EGU health impacts are attributable to emissions from eight states with significant coal combustion and large downwind populations. We estimate 10,000 premature mortalities per year from RC emissions, driven by primary PM2.5 emissions. States with large populations and significant residential wood combustion dominate RC health impacts. Annual mortality risk per thousand tons of precursor emissions (health damage functions) varied significantly across source-states for both source sectors and all precursor pollutants. Conclusions: Our findings reinforce the importance of pollutant-specific, location-specific, and source-specific models of health impacts in design of health-risk minimizing emissions control policies. Citation: Penn SL, Arunachalam S, Woody M, Heiger-Bernays W, Tripodis Y, Levy JI. 2017. Estimating state-specific contributions to PM2.5- and O3-related health burden from residential combustion and electricity generating unit emissions in the United States. Environ Health Perspect 125:324–332; http://dx.doi.org/10.1289/EHP550 PMID:27586513

78 FR 14457 - National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-06

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Parts 60 and 63 [EPA-HQ-OAR-2008-0708, FRL-9756-4] RIN 2060-AQ58 National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion Engines; New Source Performance Standards for Stationary Internal Combustion Engines Correction In rule...

NITROUS OXIDE EMISSIONS FROM FOSSIL FUEL COMBUSTION

EPA Science Inventory

The role of coal combustion as a significant global source of nitrous oxide (N2O) emissions was reexamined through on-line emission measurements from six pulverized-coal-fired utility boilers and from laboratory and pilot-scale combustors. The full-scale utility boilers yielded d...

Inter-annual variability of wintertime PM2.5 chemical composition in Xi'an, China: Evidences of changing source emissions.

PubMed

Xu, Hongmei; Cao, Junji; Chow, Judith C; Huang, R-J; Shen, Zhenxing; Chen, L W Antony; Ho, Kin Fai; Watson, John G

2016-03-01

Chemical characteristics of PM2.5 in Xi'an in wintertime of 2006, 2008, and 2010 were investigated. Markers of OC2, EC1, and NO3(-)/SO4(2-) ratio were calculated to investigate the changes in PM2.5 emission sources over the 5-year period. Positive matrix factorization (PMF) model was used to identify and quantify the main sources of PM2.5 and their contributions. The results showed that coal combustion, motor vehicular emissions, fugitive dust, and secondary inorganic aerosol accounted for more than 80% of PM2.5 mass. The importance of these major sources to the PM2.5 mass varied yearly: coal combustion was the largest contributor (31.2% ± 5.2%), followed by secondary inorganic aerosol (20.9% ± 5.2%) and motor vehicular emissions (19.3% ± 4.8%) in 2006; the order was still coal combustion emissions (27.6% ± 3.4%), secondary inorganic aerosol (23.2% ± 6.9%), and motor vehicular emissions (20.9% ± 4.6%) in 2008; while coal combustion emission further decreased (24.1% ± 3.1%) with fugitive dust (19.4% ± 5.5%) increasing in 2010. The changes in PM2.5 chemical compositions and source contributions can be attributed to the social and economic developments in Xi'an, China, including energy structure adjustment, energy consumption, the expansion of civil vehicles, and the increase of urban construction activities. Copyright © 2015 Elsevier B.V. All rights reserved.

Apparatus for photocatalytic destruction of internal combustion engine emissions during cold start

DOEpatents

Janata, Jiri; McVay, Gary L.; Peden, Charles H.; Exarhos, Gregory J.

1998-01-01

A method and apparatus for the destruction of emissions from an internal combustion engine wherein a substrate coated with TiO.sub.2 is exposed to a light source in the exhaust system of an internal combustion engine thereby catalyzing oxidation/reduction reactions between gaseous hydrocarbons, carbon monoxide, nitrogen oxides and oxygen in the exhaust of the internal combustion engine.

75 FR 9647 - National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-03

...EPA is promulgating national emission standards for hazardous air pollutants for existing stationary compression ignition reciprocating internal combustion engines that either are located at area sources of hazardous air pollutant emissions or that have a site rating of less than or equal to 500 brake horsepower and are located at major sources of hazardous air pollutant emissions. In addition, EPA is promulgating national emission standards for hazardous air pollutants for existing non-emergency stationary compression ignition engines greater than 500 brake horsepower that are located at major sources of hazardous air pollutant emissions. Finally, EPA is revising the provisions related to startup, shutdown, and malfunction for the engines that were regulated previously by these national emission standards for hazardous air pollutants.

SOURCEBOOK: NOX CONTROL TECHNOLOGY DATA

EPA Science Inventory

The report, a compilation of available information on the control of nitrogen oxide (NOx) emissions from stationary sources, is provided to assist new source permitting activities by regulatory agencies. he sources covered are combustion turbines, internal combustion engines, non...

Catalysts for cleaner combustion of coal, wood and briquettes sulfur dioxide reduction options for low emission sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, P.V.

1995-12-31

Coal fired, low emission sources are a major factor in the air quality problems facing eastern European cities. These sources include: stoker-fired boilers which feed district heating systems and also meet local industrial steam demand, hand-fired boilers which provide heat for one building or a small group of buildings, and masonary tile stoves which heat individual rooms. Global Environmental Systems is marketing through Global Environmental Systems of Polane, Inc. catalysts to improve the combustion of coal, wood or fuel oils in these combustion systems. PCCL-II Combustion Catalysts promotes more complete combustion, reduces or eliminates slag formations, soot, corrosion and somemore » air pollution emissions and is especially effective on high sulfur-high vanadium residual oils. Glo-Klen is a semi-dry powder continuous acting catalyst that is injected directly into the furnace of boilers by operating personnel. It is a multi-purpose catalyst that is a furnace combustion catalyst that saves fuel by increasing combustion efficiency, a cleaner of heat transfer surfaces that saves additional fuel by increasing the absorption of heat, a corrosion-inhibiting catalyst that reduces costly corrosion damage and an air pollution reducing catalyst that reduces air pollution type stack emissions. The reduction of sulfur dioxides from coal or oil-fired boilers of the hand fired stoker design and larger, can be controlled by the induction of the Glo-Klen combustion catalyst and either hydrated lime or pulverized limestone.« less

Regional Influence of Aerosol Emissions from Wildfires Driven by Combustion Efficiency: Insights from the BBOP Campaign.

PubMed

Collier, Sonya; Zhou, Shan; Onasch, Timothy B; Jaffe, Daniel A; Kleinman, Lawrence; Sedlacek, Arthur J; Briggs, Nicole L; Hee, Jonathan; Fortner, Edward; Shilling, John E; Worsnop, Douglas; Yokelson, Robert J; Parworth, Caroline; Ge, Xinlei; Xu, Jianzhong; Butterfield, Zachary; Chand, Duli; Dubey, Manvendra K; Pekour, Mikhail S; Springston, Stephen; Zhang, Qi

2016-08-16

Wildfires are important contributors to atmospheric aerosols and a large source of emissions that impact regional air quality and global climate. In this study, the regional and nearfield influences of wildfire emissions on ambient aerosol concentration and chemical properties in the Pacific Northwest region of the United States were studied using real-time measurements from a fixed ground site located in Central Oregon at the Mt. Bachelor Observatory (∼2700 m a.s.l.) as well as near their sources using an aircraft. The regional characteristics of biomass burning aerosols were found to depend strongly on the modified combustion efficiency (MCE), an index of the combustion processes of a fire. Organic aerosol emissions had negative correlations with MCE, whereas the oxidation state of organic aerosol increased with MCE and plume aging. The relationships between the aerosol properties and MCE were consistent between fresh emissions (∼1 h old) and emissions sampled after atmospheric transport (6-45 h), suggesting that biomass burning organic aerosol concentration and chemical properties were strongly influenced by combustion processes at the source and conserved to a significant extent during regional transport. These results suggest that MCE can be a useful metric for describing aerosol properties of wildfire emissions and their impacts on regional air quality and global climate.

COMBUSTION AREA SOURCES: DATA SOURCES

EPA Science Inventory

The report identifies, documents, and evaluates data sources for stationary area source emissions, including solid waste and agricultural burning. Area source emissions of particulate matter, sulfur dioxide, oxides of nitrogen, reactive volatile organic compounds, and carbon mon...

40 CFR 98.273 - Calculating GHG emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fossil fuels and combustion of biomass in spent liquor solids. (1) Calculate fossil fuel-based CO2 emissions from direct measurement of fossil fuels consumed and default emissions factors according to the Tier 1 methodology for stationary combustion sources in § 98.33(a)(1). (2) Calculate fossil fuel-based...

40 CFR 98.52 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... emissions at the facility level. (b) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

40 CFR 98.52 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... emissions at the facility level. (b) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

40 CFR 98.52 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... emissions at the facility level. (b) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

Apparatus for photocatalytic destruction of internal combustion engine emissions during cold start

DOEpatents

Janata, J.; McVay, G.L.; Peden, C.H.; Exarhos, G.J.

1998-07-14

A method and apparatus are disclosed for the destruction of emissions from an internal combustion engine wherein a substrate coated with TiO{sub 2} is exposed to a light source in the exhaust system of an internal combustion engine thereby catalyzing oxidation/reduction reactions between gaseous hydrocarbons, carbon monoxide, nitrogen oxides and oxygen in the exhaust of the internal combustion engine. 4 figs.

40 CFR 98.82 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (General Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and... GREENHOUSE GAS REPORTING Cement Production § 98.82 GHGs to report. You must report: (a) CO2 process emissions from calcination in each kiln. (b) CO2 combustion emissions from each kiln. (c) CH4 and N2O combustion...

40 CFR 98.82 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (General Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and... GREENHOUSE GAS REPORTING Cement Production § 98.82 GHGs to report. You must report: (a) CO2 process emissions from calcination in each kiln. (b) CO2 combustion emissions from each kiln. (c) CH4 and N2O combustion...

40 CFR 98.82 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (General Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and... GREENHOUSE GAS REPORTING Cement Production § 98.82 GHGs to report. You must report: (a) CO2 process emissions from calcination in each kiln. (b) CO2 combustion emissions from each kiln. (c) CH4 and N2O combustion...

78 FR 54606 - National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-05

... Combustion Engines; New Source Performance Standards for Stationary Internal Combustion Engines AGENCY... hazardous air pollutants for stationary reciprocating internal combustion engines and the standards of performance for stationary internal combustion engines. Subsequently, the EPA received three petitions for...

Combustion aerosols: factors governing their size and composition and implications to human health.

PubMed

Lighty, J S; Veranth, J M; Sarofim, A F

2000-09-01

Particulate matter (PM) emissions from stationary combustion sources burning coal, fuel oil, biomass, and waste, and PM from internal combustion (IC) engines burning gasoline and diesel, are a significant source of primary particles smaller than 2.5 microns (PM2.5) in urban areas. Combustion-generated particles are generally smaller than geologically produced dust and have unique chemical composition and morphology. The fundamental processes affecting formation of combustion PM and the emission characteristics of important applications are reviewed. Particles containing transition metals, ultrafine particles, and soot are emphasized because these types of particles have been studied extensively, and their emissions are controlled by the fuel composition and the oxidant-temperature-mixing history from the flame to the stack. There is a need for better integration of the combustion, air pollution control, atmospheric chemistry, and inhalation health research communities. Epidemiology has demonstrated that susceptible individuals are being harmed by ambient PM. Particle surface area, number of ultrafine particles, bioavailable transition metals, polycyclic aromatic hydrocarbons (PAH), and other particle-bound organic compounds are suspected to be more important than particle mass in determining the effects of air pollution. Time- and size-resolved PM measurements are needed for testing mechanistic toxicological hypotheses, for characterizing the relationship between combustion operating conditions and transient emissions, and for source apportionment studies to develop air quality plans. Citations are provided to more specialized reviews, and the concluding comments make suggestions for further research.

Air Quality Impact of Diffuse and Inefficient Combustion Emissions in Africa (DICE-Africa).

PubMed

Marais, Eloise A; Wiedinmyer, Christine

2016-10-04

Anthropogenic pollution in Africa is dominated by diffuse and inefficient combustion sources, as electricity access is low and motorcycles and outdated cars proliferate. These sources are missing, out-of-date, or misrepresented in state-of-the-science emission inventories. We address these deficiencies with a detailed inventory of Diffuse and Inefficient Combustion Emissions in Africa (DICE-Africa) for 2006 and 2013. Fuelwood for energy is the largest emission source in DICE-Africa, but grows from 2006 to 2013 at a slower rate than charcoal production and use, and gasoline and diesel for motorcycles, cars, and generators. Only kerosene use and gas flaring decline. Increase in emissions from 2006 to 2013 in this work is consistent with trends in satellite observations of formaldehyde and NO 2 , but much slower than the explosive growth projected with a fuel consumption model. Seasonal biomass burning is considered a large pollution source in Africa, but we estimate comparable emissions of black carbon and higher emissions of nonmethane volatile organic compounds from DICE-Africa. Nitrogen oxide (NO x ≡ NO + NO 2 ) emissions are much lower than from biomass burning. We use GEOS-Chem to estimate that the largest contribution of DICE-Africa to annual mean surface fine particulate matter (PM 2.5 ) is >5 μg m -3 in populous Nigeria.

Supply of Soluble Iron from Combustion and Dust Sources to the Ocean

NASA Astrophysics Data System (ADS)

Ito, A.

2012-12-01

Bioavailable iron (Fe) from atmospheric particle is an essential nutrient for phytoplankton. Global models have been used to deduce atmospheric iron supply to the ocean, but uncertainty in the deposition flux remains large, which can influence the air-sea fluxes of carbon dioxide and thus radiative forcing significantly. Here, a global chemical transport model is used to investigate the effect of aerosol emissions from ship plumes on iron solubility in particles from the combustion and dust sources. The emission data sets for combustion-generated aerosols such as those from biomass and fossil fuel burnings are taken from the emission inventory. The iron from combustion sources such as biomass and fossil fuels burning is readily released into solutions in aerosols assuming constant iron solubility (i.e., the mass fraction of dissolved to total iron). In contrast, the emissions of dust are calculated on-line, based on the surface wind speed and soil wetness from the GMAO assimilated meteorological fields. Further, the iron solubility dynamically changes from that in the originally emitted dust aerosols (which is 0.45%) due to reactions with acidic species. The model results reveal that the oil combustion from shipping mainly contributes to high iron solubility at low mass concentration observed over the high latitude North Atlantic Ocean. The model results suggest that the combustion source from ships contributes to a significant deposition of soluble iron to the high latitude oceans in the Northern Hemisphere. Due to continuing growth in global shipping and no regulations regarding particles emissions, the input of bioavailable iron from ship plumes is likely to increase in a future warmer climate when oceanic primary production may be more dependent on the nutrient input from atmospheric aerosols.

REVIEW AND EVALUATION OF CURRENT METHODS AND USER NEEDS FOR OTHER STATIONARY COMBUSTION SOURCES

EPA Science Inventory

The report gives results of Phase 1 of an effort to develop improved methodologies for estimating area source emissions of air pollutants from stationary combustion sources. The report (1) evaluates Area and Mobile Source (AMS) subsystem methodologies; (2) compares AMS results w...

78 FR 31315 - Kraft Pulp Mills NSPS Review

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-23

... furnaces to levels equivalent to the new source PM limits in the NESHAP for chemical recovery combustion... will enable a broader understanding of condensable PM emissions from pulp and paper combustion sources... for 0.5 seconds (no ppmdv limit). 2. Use non-combustion control device with a limit of 5 ppmdv. 3. It...

EMISIONES AL AIRE DE LA COMBUSTION DE LLANTAS USADAS (SPANISH VERSION)

EPA Science Inventory

The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

Regional Influence of Aerosol Emissions from Wildfires Driven by Combustion Efficiency: Insights from the BBOP Campaign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collier, Sonya; Zhou, Shan; Onasch, Timothy B.

Wildfires are important contributors to atmospheric aerosols and a large source of emissions that impact regional air quality and global climate. In this study, the regional and nearfield influences of wildfire emissions on ambient aerosol concentration and chemical properties in the Pacific Northwest region of the United States were studied using real-time measurements from a fixed ground site located in Central Oregon at the Mt. Bachelor Observatory (~2700 m a.s.l.) as well as near their sources using an aircraft. In addition, the regional characteristics of biomass burning aerosols were found to depend strongly on the modified combustion efficiency (MCE), anmore » index of the combustion processes of a fire. Organic aerosol emissions had negative correlations with MCE, whereas the oxidation state of organic aerosol increased with MCE and plume aging. The relationships between the aerosol properties and MCE were consistent between fresh emissions (~1 h old) and emissions sampled after atmospheric transport (6–45 h), suggesting that biomass burning organic aerosol concentration and chemical properties were strongly influenced by combustion processes at the source and conserved to a significant extent during regional transport. In conclusion, these results suggest that MCE can be a useful metric for describing aerosol properties of wildfire emissions and their impacts on regional air quality and global climate.« less

Regional Influence of Aerosol Emissions from Wildfires Driven by Combustion Efficiency: Insights from the BBOP Campaign

DOE PAGES

Collier, Sonya; Zhou, Shan; Onasch, Timothy B.; ...

2016-07-11

Wildfires are important contributors to atmospheric aerosols and a large source of emissions that impact regional air quality and global climate. In this study, the regional and nearfield influences of wildfire emissions on ambient aerosol concentration and chemical properties in the Pacific Northwest region of the United States were studied using real-time measurements from a fixed ground site located in Central Oregon at the Mt. Bachelor Observatory (~2700 m a.s.l.) as well as near their sources using an aircraft. In addition, the regional characteristics of biomass burning aerosols were found to depend strongly on the modified combustion efficiency (MCE), anmore » index of the combustion processes of a fire. Organic aerosol emissions had negative correlations with MCE, whereas the oxidation state of organic aerosol increased with MCE and plume aging. The relationships between the aerosol properties and MCE were consistent between fresh emissions (~1 h old) and emissions sampled after atmospheric transport (6–45 h), suggesting that biomass burning organic aerosol concentration and chemical properties were strongly influenced by combustion processes at the source and conserved to a significant extent during regional transport. In conclusion, these results suggest that MCE can be a useful metric for describing aerosol properties of wildfire emissions and their impacts on regional air quality and global climate.« less

Evolution of Submicrometer Organic Aerosols during a Complete Residential Coal Combustion Process.

PubMed

Zhou, Wei; Jiang, Jingkun; Duan, Lei; Hao, Jiming

2016-07-19

In the absence of particulate matter (PM) control devices, residential coal combustion contributes significantly to ambient PM pollution. Characterizing PM emissions from residential coal combustion with high time resolution is beneficial for developing control policies and evaluating the environmental impact of PM. This study reports the evolution of submicrometer organic aerosols (OA) during a complete residential coal combustion process, that is, from fire start to fire extinction. Three commonly used coal types (bituminous, anthracite, and semicoke coals) were evaluated in a typical residential stove in China. For all three types of coal, the OA emission exhibited distinct characteristics in the four stages, that is, ignition, fierce combustion, relatively stable combustion, and ember combustion. OA emissions during the ignition stage accounted for 58.2-85.4% of the total OA emission of a complete combustion process. The OA concentration decreased rapidly during the fierce combustion stage and remained low during the relatively stable combustion stage. During these two stages, a significant ion peak of m/z 73 from organic acids were observed. The degree of oxidation of the OA increased from the first stage to the last stage. Implications for ambient OA source-apportionment and residential PM emission characterization and control are discussed.

Effect of shipping emissions on European ground-level ozone

NASA Astrophysics Data System (ADS)

Stergiou, Ioannis; -Eleni Sotiropoulou, Rafaella; Tagaris, Efthimios

2017-04-01

Shipping emissions contribution to the global nitrogen oxides emissions is about 15%, affecting ozone formation and the chemical composition of the atmosphere. The objective of this study is to assess the impact of shipping emissions on ozone levels over Europe suggesting regions where air quality degradation due to shipping emissions dominates against the rest of the anthropogenic source emissions. Ranking the importance of the Standard Nomenclature for Air Pollution (SNAP) categories on ozone mixing ratio, road transport has the major impact followed by other mobile sources, power generation, and industrial combustion sectors. All other sectors have a minor impact, therefor, our analysis is focused on these four emission categories. Results suggest that shipping emissions seem to play an important role on ozone levels compared to road transport sector near the coastal zone, while they could partly offset the benefits from the emissions reduction of other mobile sources, power generation and industrial combustion sources, over a great part of the European land.

40 CFR 98.322 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Stationary Fuel Combustion Sources) the CO2, CH4, and N2O emissions from each stationary fuel combustion unit... emissions from ventilation and degasification systems. (d) You must report under this subpart the CO2 emissions from coal mine gas CH4 destruction occuring at the facility, where the gas is not a fuel input for...

40 CFR 98.322 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Stationary Fuel Combustion Sources) the CO2, CH4, and N2O emissions from each stationary fuel combustion unit... emissions from ventilation and degasification systems. (d) You must report under this subpart the CO2 emissions from coal mine gas CH4 destruction occuring at the facility, where the gas is not a fuel input for...

40 CFR 98.322 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Stationary Fuel Combustion Sources) the CO2, CH4, and N2O emissions from each stationary fuel combustion unit... emissions from ventilation and degasification systems. (d) You must report under this subpart the CO2 emissions from coal mine gas CH4 destruction occuring at the facility, where the gas is not a fuel input for...

Evaluation of the health impact of aerosols emitted from different combustion sources: Comprehensive characterization of the aerosol physicochemical properties as well as the molecular biological and toxicological effects of the aerosols on human lung cells and macrophages.

NASA Astrophysics Data System (ADS)

Zimmermann, R.; Dittmar, G.; Kanashova, T.; Buters, J.; Öder, S.; Paur, H. R.; Mülhopt, S.; Dilger, M.; Weiss, C.; Harndorf, H.; Stengel, B.; Hirvonen, M. R.; Jokiniemi, J.; Hiller, K.; Sapcariu, S.; Sippula, O.; Streibel, T.; Karg, E.; Weggler, B.; Schnelle-Kreis, J.; Lintelmann, J.; Sklorz, M.; Orasche, J.; Müller, L.; Passig, J.; Gröger, T.; Jalava, P. I.; Happo, M.; Uski, O.

2016-12-01

A novel approach to evaluate the health effects of anthropogenic combustion emissions is the detailed comparison of comprehensive physicochemical data on the combustion aerosol properties with the biological response of aerosol-exposed lung cells. In this context the "HICE-Aerosol and Health" project consortium studies the properties as well as the biological and toxicological effects on lung cells induced by different combustion aerosol emissions (e.g. ship diesel exhaust, wood combustion effluents or automobile aerosol). Human alveolar epithelial cells (e.g. A549 cells) as well as murine macrophages were exposed to diluted emissions, using field deployable ALI-exposition systems in a mobile S2-biological laboratory. This allows a realistic lung-cell exposure by simulation of the lung situation. The cellular effects were then comprehensively characterized (cytotoxicology, transcriptomics, proteomics etc.) effects monitoring and put in context with the chemical and physical aerosol data. Emissions of wood combustion, a ship engine as well as diesel and gasoline engines were investigated. Furthermore for some experiments the atmospheric aging of the emission was simulated in a flow tube reactor using UV-light and ozone. Briefly the following order of cellular response-strength was observed: A relatively mild cellular effect is observed for the diluted wood combustion emissions, regardless if log-wood and pellet burner emissions are investigated. Similarly mild biological effects are observed for gasoline car emissions. The ship diesel engine emissions and construction machine diesel engine induced much more intense biological responses. A surprising result in this context is, that heavy fuel oil (HFO)-emissions show lower biological effect strengths than the supposedly cleaner diesel fuel emissions (DF). The HFO-emissions contain high concentrations of known toxicants (metals, polycyclic aromatics). This result was confirmed by experiments with murine macrophages. Detailed analyses suggest a large difference in relative toxicity for different combustion sources. Recently the cell experiments were successively evaluated and verified by animal exposure tests. This is important to develop a reliable animal-test free-monitoring method for aerosol-induced health effects.

Evaluation of the health impact of aerosols emitted from different combustion sources: Comprehensive characterization of the aerosol physicochemical properties as well as the molecular biological and toxicological effects of the aerosols on human lung cells and macrophages.

NASA Astrophysics Data System (ADS)

Zimmermann, R.; Dittmar, G.; Kanashova, T.; Buters, J.; Öder, S.; Paur, H. R.; Mülhopt, S.; Dilger, M.; Weiss, C.; Harndorf, H.; Stengel, B.; Hirvonen, M. R.; Jokiniemi, J.; Hiller, K.; Sapcariu, S.; Sippula, O.; Streibel, T.; Karg, E.; Weggler, B.; Schnelle-Kreis, J.; Lintelmann, J.; Sklorz, M.; Orasche, J.; Müller, L.; Passig, J.; Gröger, T.; Jalava, P. I.; Happo, M.; Uski, O.

2017-12-01

A novel approach to evaluate the health effects of anthropogenic combustion emissions is the detailed comparison of comprehensive physicochemical data on the combustion aerosol properties with the biological response of aerosol-exposed lung cells. In this context the "HICE-Aerosol and Health" project consortium studies the properties as well as the biological and toxicological effects on lung cells induced by different combustion aerosol emissions (e.g. ship diesel exhaust, wood combustion effluents or automobile aerosol). Human alveolar epithelial cells (e.g. A549 cells) as well as murine macrophages were exposed to diluted emissions, using field deployable ALI-exposition systems in a mobile S2-biological laboratory. This allows a realistic lung-cell exposure by simulation of the lung situation. The cellular effects were then comprehensively characterized (cytotoxicology, transcriptomics, proteomics etc.) effects monitoring and put in context with the chemical and physical aerosol data. Emissions of wood combustion, a ship engine as well as diesel and gasoline engines were investigated. Furthermore for some experiments the atmospheric aging of the emission was simulated in a flow tube reactor using UV-light and ozone. Briefly the following order of cellular response-strength was observed: A relatively mild cellular effect is observed for the diluted wood combustion emissions, regardless if log-wood and pellet burner emissions are investigated. Similarly mild biological effects are observed for gasoline car emissions. The ship diesel engine emissions and construction machine diesel engine induced much more intense biological responses. A surprising result in this context is, that heavy fuel oil (HFO)-emissions show lower biological effect strengths than the supposedly cleaner diesel fuel emissions (DF). The HFO-emissions contain high concentrations of known toxicants (metals, polycyclic aromatics). This result was confirmed by experiments with murine macrophages. Detailed analyses suggest a large difference in relative toxicity for different combustion sources. Recently the cell experiments were successively evaluated and verified by animal exposure tests. This is important to develop a reliable animal-test free-monitoring method for aerosol-induced health effects.

Evaluation of the health impact of nanoparticles emitted from combustion sources: Comprehensive characterization of the physicochemical properties of nanoparticle emissions from wood combustion compliances, car- and ship diesel-engines as well as investigation of their toxicological effects on human lung cells and macrophages.

NASA Astrophysics Data System (ADS)

Zimmermann, R.; Dittmar, G.; Kanashova, T.; Buters, J.; Öder, S.; Paur, H. R.; Mülhopt, S.; Dilger, M.; Weiss, C.; Harndorf, H.; Stengel, B.; Hirvonen, M. R.; Jokiniemi, J.; Hiller, K.; Sapcariu, S.; Sippula, O.; Streibel, T.; Karg, E.; Weggler, B.; Schnelle-Kreis, J.; Lintelmann, J.; Sklorz, M.; Orasche, J.; Müller, L.; Passig, J.; Gröger, T.; BéruBé, K.; Krebs, T.

2016-12-01

Combustion emissions cause health effects. The HICE-Aerosol and Health project team studies the physicochemical properties as well as biological and toxicological effects on lung cells of combustion particle emissions. The chemical composition and physical parameters thoroughly characterized. Human lung cells are exposed to the diluted combustion exhaust fumes at the air-liquid interface (ALI), allowing a realistic lung-cell exposure by simulation of the lung situation. After exposure, cellular responses of the exposed lung cells are studied by multi-omics molecular biological analyses on transcriptomic, proteomic and metabolomic level. Emissions of wood combustion (log wood, pellet heater), ship diesel engines and car gasoline engines are addressed. Special field deployable ALI-exposition systems in a mobile S2-biological laboratory were set up and applied. Human alveolar epithelial cells (A549, BEAS2B and primary cells) as well as murine macrophages were ALI-exposed to diluted emissions. The cellular effects were then comprehensively characterized (viability, cyto-toxicology, multi-omics effects monitoring) and put in context with the chemical and physical aerosol data. The following order of overall cellular response-strength was observed: A relatively mild cellular effect is observed for the diluted wood combustion emissions. Interestingly the effects-strength for log-wood and pellet burner emissions are similar, although PM-concentrations are much higher for the log-wood heater. Similar mild biological effects are observed for the gasoline car emissions. The ship diesel engine emissions induced the most intense biological responses. A surprising result in this context is, that heavy fuel oil (HFO)-emissions showed lower biological effect strengths than the supposedly cleaner diesel fuel emissions (DF). The HFO-emission contain high concentrations of known toxicants (transition metals, polycyclic aromatics). This result was recently confirmed by experiments with murine RAW macrophages. Detailed analyses of the activated cellular response pathways, such as pro-inflammatory responses, xenobiotic metabolism, phagocytosis and oxidative stress were performed. The data is suggesting a large difference in relative toxicity for different combustion sources.

PREDICTION OF DIOXIN/FURAN INCINERATOR EMISSIONS USING LOW-MOLECULAR-WEIGHT VOLATILE PRODUCTS OF INCOMPLETE COMBUSTION

EPA Science Inventory

Emissions of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs) from incinerators and other stationary combustion sources are of environmental concern because of the toxicity of certain PCDD/PCDF congeners. Measurement of trace levels of PCDDs/PCDFs...

Limitation of using Angstrom exponent for source apportionment of black carbon in complex environments - A case study from the North West Indo- Gangetic plain

NASA Astrophysics Data System (ADS)

Garg, S.; Sinha, B.; Sinha, V.; Chandra, P.; Sarda Esteve, R.; Gros, V.

2015-12-01

Determining the contribution of different sources to the total BC is necessary for targeted mitigation. Absorption Angstrom exponent (αabs) measurements of black carbon (BC) have recently been introduced as a novel tool to apportion the contribution of biomass burning sources to BC. Two-component Aethalometer model for apportioning BC to biomass burning sources and fossil fuel combustion sources, which uses αabs as a generic indicator of the source type, is widely used for determining the contribution of the two types of sources to the total BC. Our work studies BC emissions in the highly-populated, anthropogenic emissions-dominated Indo-Gangetic Plain and demonstrates that the αabs cannot be used as a generic tracer for biomass burning emissions in a complex environment. Simultaneously collected high time resolution data from a 7-wavelength Aethalometer (AE 42, Magee Scientific, USA) and a high sensitivity Proton Transfer Reaction- Quadrupole Mass Spectrometer (PTR-MS) installed at a sub-urban site in Mohali (Punjab), India, were used to identify a number of biomass combustion plumes during which BC enhancements correlated strongly with an increase in acetonitrile (a well-established biomass burning tracer) mixing ratio. Each type of biomass combustion is classified and characterized by distinct emission ratios of aromatic compounds and oxygenated VOCs to acetonitrile. The identified types of biomass combustion include two different types of crop residue burning (paddy and wheat), burning of leaf-litter, and garbage burning. Traffic (fossil-fuel burning) plumes were also selected for comparison. We find that the two-component Aethalometer source-apportionment method cannot be extrapolated to all types of biomass combustion and αabs of traffic plumes can be >1 in developing countries like India, where use of adulterated fuel in vehicles is common. Thus in a complex environment, where multiple anthropogenic BC sources and air masses of variable photochemical age impact a receptor site, the angstrom exponent is not representative of the combustion type and therefore, cannot be used as a generic tracer to constrain source contributions.

GLOBAL METHANE EMISSIONS FROM MINOR ANTHROPOGENIC SOURCES AND BIOFUEL COMBUSTION IN RESIDENTIAL STOVES (JOURNAL)

EPA Science Inventory

Most global methane (CH4) budgets have failed to include emissions from a diverse group of minor anthropogenic sources. Individually, these minor sources emit small quantities of CH4, but collectively, their contributions to the budget may be significant. In this paper, CH4 emiss...

40 CFR 60.1855 - What records must I keep for municipal waste combustion units that use activated carbon?

Code of Federal Regulations, 2013 CFR

2013-07-01

... waste combustion units that use activated carbon? 60.1855 Section 60.1855 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on... waste combustion units that use activated carbon? For municipal waste combustion units that use...

40 CFR 60.1855 - What records must I keep for municipal waste combustion units that use activated carbon?

Code of Federal Regulations, 2012 CFR

2012-07-01

... waste combustion units that use activated carbon? 60.1855 Section 60.1855 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on... waste combustion units that use activated carbon? For municipal waste combustion units that use...

40 CFR 60.1855 - What records must I keep for municipal waste combustion units that use activated carbon?

Code of Federal Regulations, 2010 CFR

2010-07-01

... waste combustion units that use activated carbon? 60.1855 Section 60.1855 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on... waste combustion units that use activated carbon? For municipal waste combustion units that use...

40 CFR 60.1855 - What records must I keep for municipal waste combustion units that use activated carbon?

Code of Federal Regulations, 2014 CFR

2014-07-01

... waste combustion units that use activated carbon? 60.1855 Section 60.1855 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on... waste combustion units that use activated carbon? For municipal waste combustion units that use...

40 CFR 60.1855 - What records must I keep for municipal waste combustion units that use activated carbon?

Code of Federal Regulations, 2011 CFR

2011-07-01

... waste combustion units that use activated carbon? 60.1855 Section 60.1855 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on... waste combustion units that use activated carbon? For municipal waste combustion units that use...

EMISSIONS OF DIOXINS AND RELATED COMPOUNDS FROM COMBUSTION AND INCINERATION SOURCES

EPA Science Inventory

This report on the emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans was prepared as a contribution to the Pilot Study on International Information Exchange on Dioxins and Related Compounds. he report describes the state of the art with respect to combustion and th...

40 CFR 98.342 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... collection and combustion systems. (c) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

40 CFR 98.342 - GHGs to report.

Code of Federal Regulations, 2010 CFR

2010-07-01

... collection and combustion systems. (c) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

40 CFR 98.342 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... collection and combustion systems. (c) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

40 CFR 98.342 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... collection and combustion systems. (c) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

40 CFR 98.342 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... collection and combustion systems. (c) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each stationary combustion unit following the...

77 FR 282 - Proposed Settlement Agreement

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-04

... revised the National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion... the stationary internal combustion engine new source performance standards (ICE NSPS) to allow owners and operators of emergency stationary internal combustion engines to operate emergency stationary...

40 CFR 63.6085 - Am I subject to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants for Stationary Combustion Turbines What This Subpart Covers § 63.6085... combustion turbine located at a major source of HAP emissions. (a) Stationary combustion turbine means all... comprising any simple cycle stationary combustion turbine, any regenerative/recuperative cycle stationary...

Mercury speciation and emissions from coal combustion in Guiyang, Southwest China.

PubMed

Tang, Shunlin; Feng, Xinbin; Qiu, Jianrong; Yin, Guoxun; Yang, Zaichan

2007-10-01

Although China has been regarded as one of the largest anthropogenic mercury emission source with coal combustion, so far the actual measurements of Hg species and Hg emissions from the combustion and the capture of Hg in Chinese emission control devices were very limited. Aiming at Hg mercury species measurements in Guiyang, the capital city of Guizhou province in Southwest China, we studied flue gases of medium-to-small-sized industrial steam coal-firing boiler (10-30 t/h) with no control devices, medium-to-small-sized industrial steam coal-firing boiler with WFGD and large-scale coal combustion with ESPs using Ontario Hytro method. We obtained mercury emission factors of the three representative coal combustion and estimated mercury emissions in Guiyang in 2003, as well as the whole province from 1986 to 2002. Coal combustion in Guiyang emitted 1898 kg mercury to the atmosphere, of which 36% Hg is released from power plants, 41% from industrial coal combustion, and 23% from domestic users, and 267 kg is Hg(p), 813 kg is Hg(2+) and 817 kg is Hg0. Mercury emission in Guizhou province increased sharply from 5.8 t in 1986 to 16.4 t in 2002. With the implementation of national economic strategy of China's Western Development, the annual mercury emission from coal combustion in the province is estimated to be about 32 t in 2015.

A review on black carbon emissions, worldwide and in China.

PubMed

Ni, Mingjiang; Huang, Jianxin; Lu, Shengyong; Li, Xiaodong; Yan, Jianhua; Cen, Kefa

2014-07-01

Black carbon (BC) produced from open burning (OB) and controlled combustion (CC) is a range of carbonaceous products of incomplete combustion of biomass and fossil fuel, and is deemed as one of the major contributors to impact global environment and human health. BC has a strong relationship with POPs, in waste combustion, BC promotes the formation of POPs, and then the transport of POPs in the environment is highly influenced by BC. However less is known about BC formation, measurement and emissions estimation especially in developing countries such as China. Different forms of BC are produced both in CC and OB. BC emission characteristics and combustion parameters which determine BC emissions from CC and OB are discussed. Recent studies showed a lack of common methodology and the resulting data for describing the mechanisms related to BC formation during combustion processes. Because BC is a continuum carbonaceous combustion product, different sampling and measuring methods are used for measuring their emissions with great quantitative uncertainty. We discuss the commonly used BC sampling and measuring methods along with the causes for uncertainty and measures to minimizing the uncertainty. Then, we discuss the estimations of BC emission factors and emission inventory for CC and OB sources. The total emissions of BC from CC and OB in China are also estimated and compared with previous BC emission inventories in this review and we find the inventories tend to be overestimated. As China becomes the largest contributor to global BC emissions, studies for characterizing BC emissions from OB and CC sources are absent in China. Finally, we comment on the current state of BC emission research and identify major deficiencies that need to overcome. Moreover, the advancement in research tools, measuring technique in particular, as discussed in this review is critical for researchers in developing countries to improve their capability to study BC emissions for addressing the growing climate change and public health concerns. Copyright © 2014 Elsevier Ltd. All rights reserved.

40 CFR 98.173 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... associated requirements for Tier 4 in subpart C of this part (General Stationary Fuel Combustion Sources). (b... basis (% CO2). Q = Hourly stack gas volumetric flow rate (scfh). %H2O = Hourly moisture percentage in... vented through the same stack as any combustion unit or process equipment that reports CO2 emissions...

40 CFR 98.173 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... associated requirements for Tier 4 in subpart C of this part (General Stationary Fuel Combustion Sources). (b... basis (% CO2). Q = Hourly stack gas volumetric flow rate (scfh). %H2O = Hourly moisture percentage in... vented through the same stack as any combustion unit or process equipment that reports CO2 emissions...

Source-receptor reconciliation of fine-particulate emissions from residential wood combustion in the southeastern United States

EPA Science Inventory

An extensive collection of speciated PM2.5 measurements including organic tracers permitted a detailed examination of the emissions from residential wood combustion (RWC) in the southeastern United States over an entire year (2007). The Community Multiscale Air Quality model-base...

RESEARCH AREA -- MUNICIPAL WASTE COMBUSTION (AIR POLLUTION TECHNOLOGY BRANCH, AIR POLLUTION PREVENTION AND CONTROL DIVISION, NRMRL)

EPA Science Inventory

The municipal waste combustion (MWC) program supports the development of revised rules for air pollutant emissions from the MWC source category. Basic research is performed on MWC pollutant formation and control mechanisms for acid gas, trace organic, and trace metal emissions. T...

Emission factors of particulate matter, polycyclic aromatic hydrocarbons, and levoglucosan from wood combustion in south-central Chile.

PubMed

Jimenez, Jorge; Farias, Oscar; Quiroz, Roberto; Yañez, Jorge

2017-07-01

In south-central Chile, wood stoves have been identified as an important source of air pollution in populated areas. Eucalyptus (Eucalyptus globulus), Chilean oak (Nothofagus oblique), and mimosa (Acacia dealbata) were burned in a single-chamber slow-combustion wood stove at a controlled testing facility located at the University of Concepción, Chile. In each experiment, 2.7-3.1 kg of firewood were combusted while continuously monitoring temperature, exhaust gases, burn rate, and collecting particulate matter samples in Teflon filters under isokinetic conditions for polycyclic aromatic hydrocarbon and levoglucosan analyses. Mean particulate matter emission factors were 2.03, 4.06, and 3.84 g/kg dry wood for eucalyptus, oak, and mimosa, respectively. The emission factors were inversely correlated with combustion efficiency. The mean emission factors of the sums of 12 polycyclic aromatic hydrocarbons in particle phases were 1472.5, 2134.0, and 747.5 μg/kg for eucalyptus, oak, and mimosa, respectively. Fluoranthene, pyrene, benzo[a]anthracene, and chrysene were present in the particle phase in higher proportions compared with other polycyclic aromatic hydrocarbons that were analyzed. Mean levoglucosan emission factors were 854.9, 202.3, and 328.0 mg/kg for eucalyptus, oak, and mimosa, respectively. Since the emissions of particulate matter and other pollutants were inversely correlated with combustion efficiency, implementing more efficient technologies would help to reduce air pollutant emissions from wood combustion. Residential wood burning has been identified as a significant source of air pollution in populated areas. Local wood species are combusted for home cooking and heating, which releases several toxic air pollutants, including particulate matter, carbon monoxide, and polycyclic aromatic hydrocarbons. Air pollutant emissions depend on the type of wood and the technology and operational conditions of the wood stove. A better understanding of emissions from local wood species and wood stove performance would help to identify better biomass fuels and wood stove technologies in order to reduce air pollution from residential wood burning.

Chemometric techniques in distribution, characterisation and source apportionment of polycyclic aromatic hydrocarbons (PAHS) in aquaculture sediments in Malaysia.

PubMed

Retnam, Ananthy; Zakaria, Mohamad Pauzi; Juahir, Hafizan; Aris, Ahmad Zaharin; Zali, Munirah Abdul; Kasim, Mohd Fadhil

2013-04-15

This study investigated polycyclic aromatic hydrocarbons (PAHs) pollution in surface sediments within aquaculture areas in Peninsular Malaysia using chemometric techniques, forensics and univariate methods. The samples were analysed using soxhlet extraction, silica gel column clean-up and gas chromatography mass spectrometry. The total PAH concentrations ranged from 20 to 1841 ng/g with a mean of 363 ng/g dw. The application of chemometric techniques enabled clustering and discrimination of the aquaculture sediments into four groups according to the contamination levels. A combination of chemometric and molecular indices was used to identify the sources of PAHs, which could be attributed to vehicle emissions, oil combustion and biomass combustion. Source apportionment using absolute principle component scores-multiple linear regression showed that the main sources of PAHs are vehicle emissions 54%, oil 37% and biomass combustion 9%. Land-based pollution from vehicle emissions is the predominant contributor of PAHs in the aquaculture sediments of Peninsular Malaysia. Copyright © 2013 Elsevier Ltd. All rights reserved.

Emissions from Combustion of Open Area Sources: Prescribed Forest and Agricultural Burns

EPA Science Inventory

Emissions from wildfires and prescribed forest and agricultural burns generate a variety of emissions that can cause adverse health effects for humans, contribute to climate change, and decrease visibility. Only limited pollutant data are available for these sources, particularly...

40 CFR Table 2 to Subpart Aaaa of... - Carbon Monoxide Emission Limits for New Small Municipal Waste Combustion Units

Code of Federal Regulations, 2012 CFR

2012-07-01

... Small Municipal Waste Combustion Units 2 Table 2 to Subpart AAAA of Part 60 Protection of Environment... SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is... New Small Municipal Waste Combustion Units For the following municipal waste combustion units You must...

40 CFR Table 2 to Subpart Aaaa of... - Carbon Monoxide Emission Limits for New Small Municipal Waste Combustion Units

Code of Federal Regulations, 2011 CFR

2011-07-01

... Small Municipal Waste Combustion Units 2 Table 2 to Subpart AAAA of Part 60 Protection of Environment... SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is... New Small Municipal Waste Combustion Units For the following municipal waste combustion units You must...

40 CFR Table 2 to Subpart Aaaa of... - Carbon Monoxide Emission Limits for New Small Municipal Waste Combustion Units

Code of Federal Regulations, 2013 CFR

2013-07-01

... Small Municipal Waste Combustion Units 2 Table 2 to Subpart AAAA of Part 60 Protection of Environment... SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is... New Small Municipal Waste Combustion Units For the following municipal waste combustion units You must...

40 CFR Table 2 to Subpart Aaaa of... - Carbon Monoxide Emission Limits for New Small Municipal Waste Combustion Units

Code of Federal Regulations, 2010 CFR

2010-07-01

... Small Municipal Waste Combustion Units 2 Table 2 to Subpart AAAA of Part 60 Protection of Environment... SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is... New Small Municipal Waste Combustion Units For the following municipal waste combustion units You must...

40 CFR Table 2 to Subpart Aaaa of... - Carbon Monoxide Emission Limits for New Small Municipal Waste Combustion Units

Code of Federal Regulations, 2014 CFR

2014-07-01

... Small Municipal Waste Combustion Units 2 Table 2 to Subpart AAAA of Part 60 Protection of Environment... SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is... New Small Municipal Waste Combustion Units For the following municipal waste combustion units You must...

Anthropogenic fugitive, combustion and industrial dust is a significant, underrepresented fine particulate matter source in global atmospheric models

NASA Astrophysics Data System (ADS)

Philip, Sajeev; Martin, Randall V.; Snider, Graydon; Weagle, Crystal L.; van Donkelaar, Aaron; Brauer, Michael; Henze, Daven K.; Klimont, Zbigniew; Venkataraman, Chandra; Guttikunda, Sarath K.; Zhang, Qiang

2017-04-01

Global measurements of the elemental composition of fine particulate matter across several urban locations by the Surface Particulate Matter Network reveal an enhanced fraction of anthropogenic dust compared to natural dust sources, especially over Asia. We develop a global simulation of anthropogenic fugitive, combustion, and industrial dust which, to our knowledge, is partially missing or strongly underrepresented in global models. We estimate 2-16 μg m-3 increase in fine particulate mass concentration across East and South Asia by including anthropogenic fugitive, combustion, and industrial dust emissions. A simulation including anthropogenic fugitive, combustion, and industrial dust emissions increases the correlation from 0.06 to 0.66 of simulated fine dust in comparison with Surface Particulate Matter Network measurements at 13 globally dispersed locations, and reduces the low bias by 10% in total fine particulate mass in comparison with global in situ observations. Global population-weighted PM2.5 increases by 2.9 μg m-3 (10%). Our assessment ascertains the urgent need of including this underrepresented fine anthropogenic dust source into global bottom-up emission inventories and global models.

Source Apportionment of Elemental Carbon in Beijing, China: Insights from Radiocarbon and Organic Marker Measurements.

PubMed

Zhang, Yan-Lin; Schnelle-Kreis, Jürgen; Abbaszade, Gülcin; Zimmermann, Ralf; Zotter, Peter; Shen, Rong-rong; Schäfer, Klaus; Shao, Longyi; Prévôt, André S H; Szidat, Sönke

2015-07-21

Elemental carbon (EC) or black carbon (BC) in the atmosphere has a strong influence on both climate and human health. In this study, radiocarbon ((14)C) based source apportionment is used to distinguish between fossil fuel and biomass burning sources of EC isolated from aerosol filter samples collected in Beijing from June 2010 to May 2011. The (14)C results demonstrate that EC is consistently dominated by fossil-fuel combustion throughout the whole year with a mean contribution of 79% ± 6% (ranging from 70% to 91%), though EC has a higher mean and peak concentrations in the cold season. The seasonal molecular pattern of hopanes (i.e., a class of organic markers mainly emitted during the combustion of different fossil fuels) indicates that traffic-related emissions are the most important fossil source in the warm period and coal combustion emissions are significantly increased in the cold season. By combining (14)C based source apportionment results and picene (i.e., an organic marker for coal emissions) concentrations, relative contributions from coal (mainly from residential bituminous coal) and vehicle to EC in the cold period were estimated as 25 ± 4% and 50 ± 7%, respectively, whereas the coal combustion contribution was negligible or very small in the warm period.

Adjustment of the flue gas path in small combustion appliances with regard to particulate matter reduction

NASA Astrophysics Data System (ADS)

Sulovcová, Katarína; Jandačka, Jozef; Nosek, Radovan

2014-08-01

Concentration of solid particles in ambient atmosphere is increasing in many countries nowadays. Particulate matter pollution in higher concentration has harmful impact on human and animal health. Source of particulate matter are not only industry and traffic. Small heat sources with biomass combustion, especially during winter heating season, are also significant producer of particulate matter emission. There is a huge importance to decrease quantities of solid particles which are getting into the atmosphere in every region of their production in order to decrease environmental pollution and improve air quality. The ability of flue gas emission elimination can influence future using of biomass combustion. Therefore effective and affordable solutions are searching for. The paper deals with the reduction of particulate matter in small heat source with biomass combustion by modification of geometric parameters in flue gas path.

Highly controlled, reproducible measurements of aerosol emissions from combustion of a common African biofuel source

NASA Astrophysics Data System (ADS)

Haslett, Sophie L.; Thomas, J. Chris; Morgan, William T.; Hadden, Rory; Liu, Dantong; Allan, James D.; Williams, Paul I.; Keita, Sekou; Liousse, Cathy; Coe, Hugh

2018-01-01

Particulate emissions from biomass burning can both alter the atmosphere's radiative balance and cause significant harm to human health. However, due to the large effect on emissions caused by even small alterations to the way in which a fuel burns, it is difficult to study particulate production of biomass combustion mechanistically and in a repeatable manner. In order to address this gap, in this study, small wood samples sourced from Côte D'Ivoire in West Africa were burned in a highly controlled laboratory environment. The shape and mass of samples, available airflow and surrounding thermal environment were carefully regulated. Organic aerosol and refractory black carbon emissions were measured in real time using an Aerosol Mass Spectrometer and a Single Particle Soot Photometer, respectively. This methodology produced remarkably repeatable results, allowing aerosol emissions to be mapped directly onto different phases of combustion. Emissions from pyrolysis were visible as a distinct phase before flaming was established. After flaming combustion was initiated, a black-carbon-dominant flame was observed during which very little organic aerosol was produced, followed by a period that was dominated by organic-carbon-producing smouldering combustion, despite the presence of residual flaming. During pyrolysis and smouldering, the two phases producing organic aerosol, distinct mass spectral signatures that correspond to previously reported variations in biofuel emissions measured in the atmosphere are found. Organic aerosol emission factors averaged over an entire combustion event were found to be representative of the time spent in the pyrolysis and smouldering phases, rather than reflecting a coupling between emissions and the mass loss of the sample. Further exploration of aerosol yields from similarly carefully controlled fires and a careful comparison with data from macroscopic fires and real-world emissions will help to deliver greater constraints on the variability of particulate emissions in atmospheric systems.

Characterizing and sourcing ambient PM2.5 over key emission regions in China II: Organic molecular markers and CMB modeling

NASA Astrophysics Data System (ADS)

Zhou, Jiabin; Xiong, Ying; Xing, Zhenyu; Deng, Junjun; Du, Ke

2017-08-01

From November 2012 to July 2013, a sampling campaign was completed for comprehensive characterization of PM2.5 over four key emission regions in China: Beijing-Tianjin-Hebei (BTH), Yangzi River Delta (YRD), Pearl River Delta (PRD), and Sichuan Basin (SB). A multi-method approach, adopting different analytical and receptor modeling methods, was employed to determine the relative abundances of region-specific air pollution constituents and contributions of emission sources. This paper is focused on organic molecular marker based source apportionment using chemical mass balance (CMB) receptor modeling. Analyses of the organic molecular markers revealed that vehicle emission, coal combustion, biomass burning, meat cooking and natural gas combustion were the major contributors to organic carbon (OC) in PM2.5. The vehicle emission dominated the sources contributing to OC in spring at four sampling sites. During wintertime, the coal combustion had highest contribution to OC at BTH site, while the major source contributing to OC at YRD and PRD sites was vehicle emission. In addition, the relative contributions of different emission sources to PM2.5 mass at a specific location site and in a specific season revealed seasonal and spatial variations across all four sampling locations. The largest contributor to PM2.5 mass was secondary sulfate (14-17%) in winter at the four sites. The vehicle emission was found to be the major source (14-21%) for PM2.5 mass at PRD site. The secondary ammonium has minor variation (4-5%) across the sites, confirming the influences of regional emission sources on these sites. The distinct patterns of seasonal and spatial variations of source apportionment observed in this study were consistent with the findings in our previous paper based upon water-soluble ions and carbonaceous fractions. This makes it essential for the local government to make season- and region-specific mitigation strategies for abating PM2.5 pollution in China.

Seasonal variations and source apportionment of atmospheric PM2.5-bound polycyclic aromatic hydrocarbons in a mixed multi-function area of Hangzhou, China.

PubMed

Lu, Hao; Wang, Shengsheng; Li, Yun; Gong, Hui; Han, Jingyi; Wu, Zuliang; Yao, Shuiliang; Zhang, Xuming; Tang, Xiujuan; Jiang, Boqiong

2017-07-01

To reveal the seasonal variations and sources of PM 2.5 -bound polycyclic aromatic hydrocarbons (PAHs) during haze and non-haze episodes, daily PM 2.5 samples were collected from March 2015 to February 2016 in a mixed multi-function area in Hangzhou, China. Ambient concentrations of 16 priority-controlled PAHs were determined. The sums of PM 2.5 -bound PAH concentrations during the haze episodes were 4.52 ± 3.32 and 13.6 ± 6.29 ng m -3 in warm and cold seasons, respectively, which were 1.99 and 1.49 times those during the non-haze episodes. Four PAH sources were identified using the positive matrix factorization model and conditional probability function, which were vehicular emissions (45%), heavy oil combustion (23%), coal and natural gas combustion (22%), and biomass combustion (10%). The four source concentrations of PAHs consistently showed higher levels in the cold season, compared with those in the warm season. Vehicular emissions were the most considerable sources that result in the increase of PM 2.5 -bound PAH levels during the haze episodes, and heavy oil combustion played an important role in the aggravation of haze pollution. The analysis of air mass back trajectories indicated that air mass transport had an influence on the PM 2.5 -bound PAH pollution, especially on the increased contributions from coal combustion and vehicular emissions in the cold season.

Impacts of Combustion Conditions and Photochemical Processing on the Light Absorption of Biomass Combustion Aerosol.

PubMed

Martinsson, J; Eriksson, A C; Nielsen, I Elbæk; Malmborg, V Berg; Ahlberg, E; Andersen, C; Lindgren, R; Nyström, R; Nordin, E Z; Brune, W H; Svenningsson, B; Swietlicki, E; Boman, C; Pagels, J H

2015-12-15

The aim was to identify relationships between combustion conditions, particle characteristics, and optical properties of fresh and photochemically processed emissions from biomass combustion. The combustion conditions included nominal and high burn rate operation and individual combustion phases from a conventional wood stove. Low temperature pyrolysis upon fuel addition resulted in "tar-ball" type particles dominated by organic aerosol with an absorption Ångström exponent (AAE) of 2.5-2.7 and estimated Brown Carbon contributions of 50-70% to absorption at the climate relevant aethalometer-wavelength (520 nm). High temperature combustion during the intermediate (flaming) phase was dominated by soot agglomerates with AAE 1.0-1.2 and 85-100% of absorption at 520 nm attributed to Black Carbon. Intense photochemical processing of high burn rate flaming combustion emissions in an oxidation flow reactor led to strong formation of Secondary Organic Aerosol, with no or weak absorption. PM1 mass emission factors (mg/kg) of fresh emissions were about an order of magnitude higher for low temperature pyrolysis compared to high temperature combustion. However, emission factors describing the absorption cross section emitted per kg of fuel consumed (m(2)/kg) were of similar magnitude at 520 nm for the diverse combustion conditions investigated in this study. These results provide a link between biomass combustion conditions, emitted particle types, and their optical properties in fresh and processed plumes which can be of value for source apportionment and balanced mitigation of biomass combustion emissions from a climate and health perspective.

40 CFR 63.861 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda, Sulfite, and...

40 CFR 63.861 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda, Sulfite, and...

40 CFR 98.182 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and N2O... GREENHOUSE GAS REPORTING Lead Production § 98.182 GHGs to report. You must report: (a) Process CO2 emissions from each smelting furnace used for lead production. (b) CO2 combustion emissions from each smelting...

40 CFR 98.182 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and N2O... GREENHOUSE GAS REPORTING Lead Production § 98.182 GHGs to report. You must report: (a) Process CO2 emissions from each smelting furnace used for lead production. (b) CO2 combustion emissions from each smelting...

40 CFR 98.182 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and N2O... GREENHOUSE GAS REPORTING Lead Production § 98.182 GHGs to report. You must report: (a) Process CO2 emissions from each smelting furnace used for lead production. (b) CO2 combustion emissions from each smelting...

40 CFR 98.182 - GHGs to report.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and N2O... GREENHOUSE GAS REPORTING Lead Production § 98.182 GHGs to report. You must report: (a) Process CO2 emissions from each smelting furnace used for lead production. (b) CO2 combustion emissions from each smelting...

40 CFR 98.182 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Stationary Fuel Combustion Sources) by following the requirements of subpart C. (d) CO2, CH4, and N2O... GREENHOUSE GAS REPORTING Lead Production § 98.182 GHGs to report. You must report: (a) Process CO2 emissions from each smelting furnace used for lead production. (b) CO2 combustion emissions from each smelting...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

40 CFR 60.1690 - What are the operating practice requirements for my municipal waste combustion unit?

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements for my municipal waste combustion unit? 60.1690 Section 60.1690 Protection of Environment... SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operating Requirements § 60.1690 What...

Climate Change Impacts of US Reactive Nitrogen Emissions

NASA Astrophysics Data System (ADS)

Pinder, R. W.; Davidson, E. A.; Goodale, C. L.; Greaver, T.; Herrick, J.; Liu, L.

2011-12-01

By fossil fuel combustion and fertilizer application, the US has substantially altered the nitrogen cycle, with serious effects on climate change. The climate effects can be short-lived, by impacting the chemistry of the atmosphere, or long-lived, by altering ecosystem greenhouse gas fluxes. Here, we develop a coherent framework for assessing the climate change impacts of US reactive nitrogen emissions. We use the global temperature potential (GTP) as a common metric, and we calculate the GTP at 20 and 100 years in units of CO2 equivalents. At both time-scales, nitrogen enhancement of CO2 uptake has the largest impact, because in the eastern US, areas of high nitrogen deposition are co-located with forests. In the short-term, the effect due to NOx altering ozone and methane concentrations is also substantial, but are not important on the 100 year time scale. Finally, the GTP of N2O emissions is substantial at both time scales. We have also attributed these impacts to combustion and agricultural sources, and quantified the uncertainty. Reactive nitrogen from combustion sources contribute more to cooling than warming. The impacts of agricultural sources tend to cancel each other out, and the net effect is uncertain. Recent trends show decreasing reactive nitrogen from US combustion sources, while agricultural sources are increasing. Fortunately, there are many mitigation strategies currently available to reduce the climate change impacts of US agricultural sources.

Estimate of sulfur, arsenic, mercury, fluorine emissions due to spontaneous combustion of coal gangue: An important part of Chinese emission inventories.

PubMed

Wang, Shaobin; Luo, Kunli; Wang, Xing; Sun, Yuzhuang

2016-02-01

A rough estimate of the annual amount of sulfur, arsenic, mercury and fluoride emission from spontaneous combustion of coal gangue in China was determined. The weighted mean concentrations of S, As, Hg, and F in coal gangue are 1.01%, 7.98, 0.18, and 365.54 mg/kg, respectively. Amounts of S, As, Hg, and F emissions from coal gangue spontaneous combustion show approximately 1.13 Mt, and 246, 45, and 63,298 tons in 2013, respectively. The atmospheric release amount of sulfur from coal gangue is more than one tenth of this from coal combustion, and the amounts of As, Hg, and F are close to or even exceed those from coal combustion. China's coal gangue production growth from 1992 to 2013 show an obvious growth since 2002. It may indicate that Chinese coal gangue has become a potential source of air pollution, which should be included in emission inventories. Copyright © 2015 Elsevier Ltd. All rights reserved.

Physicochemical characterization of fine particles from small-scale wood combustion

NASA Astrophysics Data System (ADS)

Lamberg, Heikki; Nuutinen, Kati; Tissari, Jarkko; Ruusunen, Jarno; Yli-Pirilä, Pasi; Sippula, Olli; Tapanainen, Maija; Jalava, Pasi; Makkonen, Ulla; Teinilä, Kimmo; Saarnio, Karri; Hillamo, Risto; Hirvonen, Maija-Riitta; Jokiniemi, Jorma

2011-12-01

Emissions from small-scale wood combustion appliances are of special interest since fine particles have been consistently associated with adverse health effects. It has been reported that the physicochemical characteristics of the emitted particles affect also their toxic properties but the mechanisms behind these phenomena and the causative role of particles from wood combustion sources are still mostly unknown. Combustion situations vary significantly in small-scale appliances, especially in batch combustion. Combustion behaviour is affected by fuel properties, appliance type and operational practice. Particle samples were collected from six appliances representing different combustion situations in small-scale combustion. These appliances were five wood log fuelled stoves, including one stove equipped with modern combustion technology, three different conventional combustion appliances and one sauna stove. In addition, a modern small-scale pellet boiler represented advanced continuous combustion technology. The aim of the study was to analyze gas composition and fine particle properties over different combustion situations. Fine particle (PM 1) emissions and their chemical constituents emerging from different combustion situations were compared and this physicochemical data was combined with the toxicological data on cellular responses induced by the same particles (see Tapanainen et al., 2011). There were significant differences in the particle emissions from different combustion situations. Overall, the efficient combustion in the pellet boiler produced the smallest emissions whereas inefficient batch combustion in a sauna stove created the largest emissions. Improved batch combustion with air-staging produced about 2.5-fold PM 1 emissions compared to the modern pellet boiler (50.7 mg MJ -1 and 19.7 mg MJ -1, respectively), but the difference in the total particulate PAH content was 750-fold (90 μg MJ -1 and 0.12 μg MJ -1, respectively). Improved batch combustion and conventional batch combustion showed almost the same PM 1 emissions (51.6 mg MJ -1), but a 10-fold difference in total particulate PAH emissions (910 μg MJ -1). These results highlight that same PM 1 emissions can be associated with very different chemical compositions, potentially leading to different toxic properties of the particles. Thus, changing from an old, less efficient, combustion appliance to a modern appliance can have a greater impact on toxic properties than the emitted PM 1 mass might indicate.

Optical Power Source Derived from Engine Combustion Chambers

NASA Technical Reports Server (NTRS)

Baumbick, Robert J. (Inventor)

1999-01-01

An optical power source is disclosed that collects the spectra of the light emissions created in a combustion chamber to provide its optical output signals that serve the needs of optical networks. The light spectra is collected by a collection ring serving as an optical waveguide.

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 63.867 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 63.867 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...

40 CFR 63.864 - Monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 63.864 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft...

40 CFR 63.864 - Monitoring requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Section 63.864 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft...

Atmospheric lead deposition to Okefenokee Swamp, Georgia, USA

USGS Publications Warehouse

Jackson, B.P.; Winger, P.V.; Lasier, P.J.

2004-01-01

'Capsule:' Coal combustion emissions appear to be a major source of Pb in the Okefenokee wetland. Contamination of the environment from atmospheric deposition during the twentieth century is pervasive even in areas ostensibly considered pristine or remote from point sources. In this study, Pb concentrations in a Pb-210-dated peat core collected from the Okefenokee Swamp, GA were used to assess historical contaminant input via atmospheric deposition. Lead isotope ratios were determined by dynamic reaction cell ICP-MS (DRC-ICP-MS). Increases in Pb concentration occurred in the late nineteenth century and a marked rise in Pb concentrations pre-dated the widespread use of leaded gasoline within the US. The Pb-206/Pb-207 ratios of 1.19 during this period were consistent with coal combustion emissions. A later increase in Pb concentration, concurrent with a trend toward more radiogenic Pb-206/Pb-207 ratios in gasoline is consistent with an increased input of Pb from leaded gasoline emissions. However, it appears that coal combustion emissions remain a major source of Pb to the Okefenokee.

Modeling Secondary Organic Aerosol Formation From Emissions of Combustion Sources

NASA Astrophysics Data System (ADS)

Jathar, Shantanu Hemant

Atmospheric aerosols exert a large influence on the Earth's climate and cause adverse public health effects, reduced visibility and material degradation. Secondary organic aerosol (SOA), defined as the aerosol mass arising from the oxidation products of gas-phase organic species, accounts for a significant fraction of the submicron atmospheric aerosol mass. Yet, there are large uncertainties surrounding the sources, atmospheric evolution and properties of SOA. This thesis combines laboratory experiments, extensive data analysis and global modeling to investigate the contribution of semi-volatile and intermediate volatility organic compounds (SVOC and IVOC) from combustion sources to SOA formation. The goals are to quantify the contribution of these emissions to ambient PM and to evaluate and improve models to simulate its formation. To create a database for model development and evaluation, a series of smog chamber experiments were conducted on evaporated fuel, which served as surrogates for real-world combustion emissions. Diesel formed the most SOA followed by conventional jet fuel / jet fuel derived from natural gas, gasoline and jet fuel derived from coal. The variability in SOA formation from actual combustion emissions can be partially explained by the composition of the fuel. Several models were developed and tested along with existing models using SOA data from smog chamber experiments conducted using evaporated fuel (this work, gasoline, fischertropschs, jet fuel, diesels) and published data on dilute combustion emissions (aircraft, on- and off-road gasoline, on- and off-road diesel, wood burning, biomass burning). For all of the SOA data, existing models under-predicted SOA formation if SVOC/IVOC were not included. For the evaporated fuel experiments, when SVOC/IVOC were included predictions using the existing SOA model were brought to within a factor of two of measurements with minor adjustments to model parameterizations. Further, a volatility-only model suggested that differences in the volatility of the precursors were able to explain most of the variability observed in the SOA formation. For aircraft exhaust, the previous methods to simulate SOA formation from SVOC and IVOC performed poorly. A more physically-realistic modeling framework was developed, which was then used to show that SOA formation from aircraft exhaust was (a) higher for petroleum-based than synthetically derived jet fuel and (b) higher at lower engine loads and vice versa. All of the SOA data from combustion emissions experiments were used to determine source-specific parameterizations to model SOA formation from SVOC, IVOC and other unspeciated emissions. The new parameterizations were used to investigate their influence on the OA budget in the United States. Combustion sources were estimated to emit about 2.61 Tg yr-1 of SVOC, 1VOC and other unspeciated emissions (sixth of the total anthropogenic organic emissions), which are predicted to double SOA production from combustion sources in the United States. The contribution of SVOC and IVOC emissions to global SOA formation was assessed using a global climate model. Simulations were performed using a modified version of GISS GCM 11'. The modified model predicted that SVOC and IVOC contributed to half of the OA mass in the atmosphere. Their inclusion improved OA model-measurement comparisons for absolute concentrations, POA-SOA split and volatility (gas-particle partitioning) globally suggesting that atmospheric models need to incorporate SOA formation from SVOC and IVOC if they are to reasonably predict the abundance and properties of aerosols. This thesis demonstrates that SVOC/IVOC and possibly other unspeciated organics emitted by combustion sources are very important precursors of SOA and potentially large contributors to the atmospheric aerosol mass. Models used for research and policy applications need to represent them to improve model-predictions of aerosols on climate and health outcomes. The improved modeling frameworks developed in this dissertation are suitable for implementation into chemical transport models.

An important missing source of atmospheric carbonyl sulfide: Domestic coal combustion

NASA Astrophysics Data System (ADS)

Du, Qianqian; Zhang, Chenglong; Mu, Yujing; Cheng, Ye; Zhang, Yuanyuan; Liu, Chengtang; Song, Min; Tian, Di; Liu, Pengfei; Liu, Junfeng; Xue, Chaoyang; Ye, Can

2016-08-01

Carbonyl sulfide (COS), carbon monoxide (CO), and sulfur dioxide (SO2) emissions generated from prevailing domestic coal stoves fueled with raw bituminous coal were studied under alternation cycles of flaming and smoldering combustion. The measurements in the laboratory and the farmer's house indicated that COS and CO emissions mainly occurred under the condition of flame extinguishment after coal loading, whereas SO2 emissions were mainly generated through combustion with flame. The COS emission factors for the domestic stoves in the laboratory and the farmer's house were recorded as 0.57 ± 0.10 g COS kg-1 and 1.43 ± 0.32 g COS kg-1, being approximately a factor of 50 and 125 greater than that generated from coal power plants, respectively. Based on the COS emission factors measured in this study, COS emission from only domestic coal combustion in China would be at least 30.5 ± 5.6 Gg S yr-1 which was 1 magnitude greater than the current COS estimation from the total coal combustion in China.

DEVELOPMENT OF SAMPLING AND ANALYTICAL METHODS FOR THE MEASUREMENT OF NITROUS OXIDE FROM FOSSIL FUEL COMBUSTION SOURCES

EPA Science Inventory

The report documents the technical approach and results achieved while developing a grab sampling method and an automated, on-line gas chromatography method suitable to characterize nitrous oxide (N2O) emissions from fossil fuel combustion sources. The two methods developed have...

ATTRIBUTION OF PARTICLE EXPOSURE AND RISK TO COMBUSTION SOURCE EMISSIONS BASED ON PERSONAL PAH EXPOSURE AND URINARY METABOLITES

EPA Science Inventory

Personal airborne exposures to carcinogenic particulate PAH have been significantly correlated with exposure to respirable fine particle mass (PM 2.5) in several studies. All combustion sources emit PAH, however the relative concentrations of different PAH and other organic tr...

78 FR 41735 - Approval and Promulgation of Air Quality Implementation Plans; Indiana; Redesignation of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-11

... and Applicable Federal Air Pollution Control Regulations and Other Permanent and Enforceable... Cross-State Air Pollution Rule (CSAPR) and ordered EPA to continue administering the Clean Air... combustion emissions of NO X from power plants, mobile sources and other combustion sources. The first air...

THE PHYSICAL AND CHEMICAL CHARACTERIZATION OF THE EMISSIONS FROM A RESIDENTIAL OIL BOILER

EPA Science Inventory

The toxicity of emissions from the combustion of home heating oil and the use of residential oil boilers (ROB) is an important health concern. Yet scant physical and chemical information about the emissions from this source are available for dispersion, climate, and source-recep...

40 CFR 60.1545 - Does this subpart directly affect municipal waste combustion unit owners and operators in my State?

Code of Federal Regulations, 2013 CFR

2013-07-01

... municipal waste combustion unit owners and operators in my State? 60.1545 Section 60.1545 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... municipal waste combustion unit owners and operators in my State? (a) No, this subpart does not directly...

40 CFR 60.1545 - Does this subpart directly affect municipal waste combustion unit owners and operators in my State?

Code of Federal Regulations, 2014 CFR

2014-07-01

... municipal waste combustion unit owners and operators in my State? 60.1545 Section 60.1545 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... municipal waste combustion unit owners and operators in my State? (a) No, this subpart does not directly...

40 CFR 60.1565 - What subcategories of small municipal waste combustion units must I include in my State plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... waste combustion units must I include in my State plan? 60.1565 Section 60.1565 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... of small municipal waste combustion units must I include in my State plan? This subpart specifies...

40 CFR 60.1545 - Does this subpart directly affect municipal waste combustion unit owners and operators in my State?

Code of Federal Regulations, 2011 CFR

2011-07-01

... municipal waste combustion unit owners and operators in my State? 60.1545 Section 60.1545 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... municipal waste combustion unit owners and operators in my State? (a) No, this subpart does not directly...

40 CFR 60.1545 - Does this subpart directly affect municipal waste combustion unit owners and operators in my State?

Code of Federal Regulations, 2012 CFR

2012-07-01

... municipal waste combustion unit owners and operators in my State? 60.1545 Section 60.1545 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... municipal waste combustion unit owners and operators in my State? (a) No, this subpart does not directly...

40 CFR 60.1565 - What subcategories of small municipal waste combustion units must I include in my State plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... waste combustion units must I include in my State plan? 60.1565 Section 60.1565 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... of small municipal waste combustion units must I include in my State plan? This subpart specifies...

40 CFR 60.1565 - What subcategories of small municipal waste combustion units must I include in my State plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... waste combustion units must I include in my State plan? 60.1565 Section 60.1565 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... of small municipal waste combustion units must I include in my State plan? This subpart specifies...

40 CFR 60.1565 - What subcategories of small municipal waste combustion units must I include in my State plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... waste combustion units must I include in my State plan? 60.1565 Section 60.1565 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... of small municipal waste combustion units must I include in my State plan? This subpart specifies...

40 CFR 60.1545 - Does this subpart directly affect municipal waste combustion unit owners and operators in my State?

Code of Federal Regulations, 2010 CFR

2010-07-01

... municipal waste combustion unit owners and operators in my State? 60.1545 Section 60.1545 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... municipal waste combustion unit owners and operators in my State? (a) No, this subpart does not directly...

40 CFR 60.1565 - What subcategories of small municipal waste combustion units must I include in my State plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... waste combustion units must I include in my State plan? 60.1565 Section 60.1565 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... of small municipal waste combustion units must I include in my State plan? This subpart specifies...

Field Measurements of Trace Gases and Aerosols Emitted by Undersampled Combustion Sources Including Wood and Dung Cooking Fires, Garbage and Crop Residue Burning, and Indonesian Peat Fires

NASA Astrophysics Data System (ADS)

Stockwell, C.; Jayarathne, T. S.; Goetz, D.; Simpson, I. J.; Selimovic, V.; Bhave, P.; Blake, D. R.; Cochrane, M. A.; Ryan, K. C.; Putra, E. I.; Saharjo, B.; Stone, E. A.; DeCarlo, P. F.; Yokelson, R. J.

2017-12-01

Field measurements were conducted in Nepal and in the Indonesian province of Central Kalimantan to improve characterization of trace gases and aerosols emitted by undersampled combustion sources. The sources targeted included cooking with a variety of stoves, garbage burning, crop residue burning, and authentic peat fires. Trace gas and aerosol emissions were studied using a land-based Fourier transform infrared spectrometer, whole air sampling, photoacoustic extinctiometers (405 and 870nm), and filter samples that were analyzed off-line. These measurements were used to calculate fuel-based emission factors (EFs) for up to 90 gases, PM2.5, and PM2.5 constituents. The aerosol optical data measured included EFs for the scattering and absorption coefficients, the single scattering albedo (at 870 and 405 nm), as well as the absorption Ångström exponent. The emissions varied significantly by source, although light absorption by both brown and black carbon (BrC and BC, respectively) was important for all non-peat sources. For authentic peat combustion, the emissions of BC were negligible and absorption was dominated by organic aerosol. The field results from peat burning were in reasonable agreement with recent lab measurements of smoldering Kalimantan peat and compare well to the limited data available from other field studies. The EFs can be used with estimates of fuel consumption to improve regional emissions inventories and assessments of the climate and health impacts of these undersampled sources.

Sulfur dioxide emissions from combustion in china: from 1990 to 2007.

PubMed

Su, Shenshen; Li, Bengang; Cui, Siyu; Tao, Shu

2011-10-01

China has become the world's largest emitter of SO(2) since 2005, and aggressive deployment of flue gas desulfurization (FGD) at coal-fired power plants appeared in China when facing the formidable pressure of environment pollution. In this work, we estimate the annual emission from combustion sources at provincial levels in China from 1990 to 2007, with updated data investigations. We have implemented the method of transportation matrix to gain a better understanding of sulfur content of coal in consuming provinces, which in turn improved the inventory. The total emissions from combustion in 2007 were 28.3 Tg, half of which was contributed by coal-fired power plants. Meanwhile, the industrial boiler coal combustion and residential coal consumed in centralized heating were responsible for another 32% of the total emissions. From 1990 to 2007, annual SO(2) emission was fluctuated with two peaks (1996 and 2006), and total emission doubled from 15.4 Tg to 30.8 Tg, at an annual growth rate of 4.4% (6.3% since 2000). Due to the extensive application of FGD technology and the phase-out of small, high emitting units, the SO(2) emission began to decrease after 2006. Furthermore, the differences among estimates reported in literatures highlight a great need for further research to reduce the uncertainties with more detailed information on key sources and actual operation of devices.

Solid waste from Swine wastewater as a fuel source for heat production.

PubMed

Park, Myung-Ho; Kumar, Sanjay; Ra, ChangSix

2012-11-01

This study was to evaluate the feasibility of recycling the solids separated from swine wastewater treatment process as a fuel source for heat production and to provide a data set on the gas emissions and combustion properties. Also, in this study, the heavy metals in ash content were analyzed for its possible use as a fertilizer. Proximate analysis of the solid recovered from the swine wastewater after flocculation with organic polymer showed high calorific (5,330.50 kcal/kg) and low moisture (15.38%) content, indicating that the solid separated from swine wastewater can be used as an alternative fuel source. CO and NOx emissions were found to increase with increasing temperature. Combustion efficiency of the solids was found to be stable (95 to 98%) with varied temperatures. Thermogravimetry (TG) and differential thermal analysis (DTA) showed five thermal effects (four exothermic and one endothermic), and these effects were distinguished in three stages, water evaporation, heterogeneous combustion of hydrocarbons and decomposition reaction. Based on the calorific value and combustion stability results, solid separated from swine manure can be used as an alternative source of fuel, however further research is still warranted regarding regulation of CO and NOx emissions. Furthermore, the heavy metal content in ash was below the legal limits required for its usage as fertilizer.

PCDD/F EMISSIONS FROM UNCONTROLLED, DOMESTIC WASTE BURNING

EPA Science Inventory

Considerable uncertainty exists in the inventory of polychlorinated dibenzodioxin and dibenzofuran (PCDD/F) emissions from controlled combustion sources such as backyard burning of domestic waste. The contribution from these sources to the worldwide PCDD/F balance may be signific...

40 CFR 62.1115 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Landfill Gas Emissions from Existing Municipal Solid Waste Landfills § 62.1115 Identification of sources. The plan applies to existing municipal solid waste landfills for which construction, reconstruction... 51451, Sept. 23, 1999] Emissions From Small Existing Municipal Waste Combustion Units ...

Assessment of organic contaminants in emissions from refuse-derived fuel combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrostowski, J.; Wait, D.; Kwong, E.

1985-09-01

Organic contaminants in emissions from refuse-derived fuel combustion were investigated in a 20-inch-diameter atmospheric fluidized-bed combustor. Combinations of coal/EcoFuel/MSW/toluene were burned inthe combustor with temperatures ranging from 1250 to 1550 degrees F. A Source Assessment Sampling System (SASS) was used to sample the stack gas; Level 1 methodology was used to analyze the organic-contaminant levels. Combustion efficiencies of 93 to 98 percent were achieved in the test burns. Combustion of the EcoFuel generated fewer organic emissions than combustion of coal at similar combustion temperatures. The fine particulate collected by the SASS train filter contained higher concentrations of extractable organics thanmore » the reactor fly ash and the SASS cyclone samples. Combustion of a toluene/EcoFuel mix generated a large number of benzene derivatives not seen in the combustion of pure EcoFuel. Polycyclic aromatic hydrocarbons were the dominant organic compounds contained in the XAD-2 resin extract from coal combustion. A number of different priority pollutants were identified in the samples collected.« less

Impacts of updated emission inventories on source apportionment of fine particle and ozone over the southeastern U.S.

NASA Astrophysics Data System (ADS)

Zhang, Yang; Wang, Wei; Wu, Shiang-Yuh; Wang, Kai; Minoura, Hiroaki; Wang, Zifa

2014-05-01

As the U.S. Environmental Protection Agency updates the National Emission Inventory (NEI), the source contributions (SC) of major source sectors to major pollutants based on source apportionment techniques should be periodically reassessed to reflect changes in SCs due to changes in emissions. This work assesses emission updates from the 1999 NEI version 2 (NEI99v2) and the 2005 NEI (NEI05) and the resulting differences in SCs using the two inventories. Large differences exist in the emissions of nitrogen oxide, formaldehyde, ammonia, terpene, and primary PM2.5 between NEI99v2 and NEI05. Differences in emissions lead to differences in model performance and source appointment. SCs of ten major source categories to fine particulate matter (PM2.5) are estimated using the Community Multiscale Air Quality modeling system with the Brute Force Method (CMAQ/BFM) andNEI05and compared with those obtained previously using CMAQ/BFM with NEI99v2. In January, compared to CMAQ/BFM (NEI99v2), CMAQ/BFM (NEI05) shows that miscellaneous areas, biomass burning, and coal combustion remain the top three contributors to PM2.5 but with different ranking and higher SCs (17.7%, 16.0%, and 14.1% for NEI05 vs. 11.8%, 13.7%, and 10.8% for NEI99v2, respectively). In July, coal combustion, miscellaneous areas, and industrial processes remain the top three with higher SCs (41.9%, 14.1%, and 8.8% for NEI05 vs.30.8%, 8.9%, and 6.9% for NEI99v2, respectively). Those changes in SCs are attributed to increased primary PM2.5 (PPM) emissions in NEI05 and increases in relative contributions of miscellaneous areas and coal combustion to the emissions of PPM, NH3, and SO2.SCs from diesel and gasoline vehicles decrease in both months, due to decreased contributions of gasoline vehicles to SO2 and NH3 emissions and those of diesel vehicles to NOx and PPM emissions. Compared with CMAQ/BFM (NEI99v2), SCs from other combustion and biomass burning are higher in Florida, due to substantial increases in formaldehyde and PPM emissions in NEI05, resulting from higher wildfire emissions and state emission updates. SCs from industrial processes increase and those from diesel and gasoline vehicles decrease in urban areas. SCs of O3 from most sources in both months increase due to a large increase in their contributions to NOx emissions, except for diesel vehicles in July, which decreases over domainwide due to a relative decrease in NOx emissions. These results provide valuable information for policy makers to formulate and adjust emission control strategies as the NEI is continuously updated.

Atmospheric emission of mercury due to combustion of steam coal and domestic coal in China

NASA Astrophysics Data System (ADS)

Wang, Shaobin; Luo, Kunli

2017-08-01

To study the mercury emission due to the combustion of steam coal and domestic coal in China, we analyzed the mercury contents of coal, fly ash, bottom ash and sluicing water in thermal power plants, steam boilers as well as domestic coal-stoves, in Shaanxi, Shanxi, Shandong and Yunnan Provinces. This study conduct an estimate of the Hg emission rates from steam coal and domestic coal combustion based on the method of mass distribution ratio of fly ash and bottom ash. The results show that the Hg emission rate of coal combustion in thermal power plants is about 50.21% (electrostatic precipitators + wet flue gas desulfurization), and that in heating boilers is about 67.23%, and 92.28% in industrial boilers without flue gas desulphurisation equipment. Furthermore, Hg emission rate is 83.61% due to domestic coal combustion in coal-stoves. The Hg emission amount into the atmosphere from power and heat generation, industrial boilers, domestic coal-stoves and spontaneous combustion of coal gangue is roughly estimated to be 133 ± 4, 100 ± 17, 11 ± 0.1 and 47 ± 26 tons in China in 2014, respectively, and the total Hg emission amount from this paper is estimated at 292 tons. The trends of Hg emission in China from 1991 to 2014 show an accelerating growth after 2002. The proportion of mercury emission due to thermal power, heating generation and industrial energy utilization continuously increased. The atmospheric emission of mercury due to combustion of steam coal, domestic coal and coal gangue accounts nearly 50% in total anthropogenic Hg emissions in China, indicating one of the largest sources of Hg emission in China which should draw more public and scientific attention in the future.

Report: Combustion Byproducts and Their Health Effects: Summary of the 10th International Congress

PubMed Central

Dellinger, Barry; D'Alessio, Antonio; D'Anna, Andrea; Ciajolo, Anna; Gullett, Brian; Henry, Heather; Keener, Mel; Lighty, JoAnn; Lomnicki, Slawomir; Lucas, Donald; Oberdörster, Günter; Pitea, Demetrio; Suk, William; Sarofim, Adel; Smith, Kirk R.; Stoeger, Tobias; Tolbert, Paige; Wyzga, Ron; Zimmermann, Ralf

2008-01-01

Abstract The 10th International Congress on Combustion Byproducts and their Health Effects was held in Ischia, Italy, from June 17–20, 2007. It is sponsored by the US NIEHS, NSF, Coalition for Responsible Waste Incineration (CRWI), and Electric Power Research Institute (EPRI). The congress focused on: the origin, characterization, and health impacts of combustion-generated fine and ultrafine particles; emissions of mercury and dioxins, and the development/application of novel analytical/diagnostic tools. The consensus of the discussion was that particle-associated organics, metals, and persistent free radicals (PFRs) produced by combustion sources are the likely source of the observed health impacts of airborne PM rather than simple physical irritation of the particles. Ultrafine particle-induced oxidative stress is a likely progenitor of the observed health impacts, but important biological and chemical details and possible catalytic cycles remain unresolved. Other key conclusions were: (1) In urban settings, 70% of airborne fine particles are a result of combustion emissions and 50% are due to primary emissions from combustion sources, (2) In addition to soot, combustion produces one, possibly two, classes of nanoparticles with mean diameters of ~10 nm and ~1 nm. (3) The most common metrics used to describe particle toxicity, viz. surface area, sulfate concentration, total carbon, and organic carbon, cannot fully explain observed health impacts, (4) Metals contained in combustion-generated ultrafine and fine particles mediate formation of toxic air pollutants such as PCDD/F and PFRs. (5) The combination of metal-containing nanoparticles, organic carbon compounds, and PFRs can lead to a cycle generating oxidative stress in exposed organisms. PMID:22476005

Mercury emissions from industrial sources in India and its effects in the environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arun B. Mukherjee; Prosun Bhattacharya; Atanu Sarkar

2009-07-01

This study describes the atmospheric mercury (Hg) emissions from industrial sources in India for the years 2000 to 2004. There is no consistent earlier information for Hg emissions to the environment for any sectors of industry. This paper may be the first road map in which we have tried to find out the total emission of Hg from a wide range of sources, e.g. from coal combustion to clinical thermometers broken during production or packing. There is a lack of basic data and in an attempt to correct this, emission factors suitable for Asian countries have been selected to completemore » this study. Before this document, there were some efforts in Europe to develop emission inventories for Hg from coal combustion or chlor-alkali plants for India. In this study it was found that total atmospheric emission from industrial sources has decreased from 321 Mg in 2000 to 253 Mg in 2004 due to a switch for the membrane cell process in the chlor-alkali industry. In 2004 the largest part of the Hg emissions stemmed from coal combustion in thermal power plants. Hg-cell technology had been used earlier in chlorine and sodium hydroxide production, as a result of which Hg concentration in terrestrial and aquatic species are nowadays quite high in coastal areas. India can thus be referred to as a mercury 'hot spot'. Limited information is available on emissions of Hg from industrial sources in India. Estimates are based on emission factors and the values taken from the literature. Against a background of limited data and information, this paper gives an overview of Hg emissions in India and of the recent steps undertaken by authorities to curb the emissions of Hg and its subsequent trans-boundary movement in the global environment.« less

Characteristics and source apportionment of fine haze aerosol in Beijing during the winter of 2013

NASA Astrophysics Data System (ADS)

Shang, Xiaona; Zhang, Kai; Meng, Fan; Wang, Shihao; Lee, Meehye; Suh, Inseon; Kim, Daigon; Jeon, Kwonho; Park, Hyunju; Wang, Xuezhong; Zhao, Yuxi

2018-02-01

For PM2.5 filter samples collected daily at the Chinese Research Academy of Environmental Sciences (Beijing, China) from December of 2013 to February of 2014 (the winter period), chemical characteristics and sources were investigated with an emphasis on haze events in different alert levels. During the 3 months, the average PM2.5 concentration was 89 µg m-3, exceeding the Chinese national standard of 75 µg m-3 in 24  h. The maximum PM2.5 concentration was 307 µg m-3, which characterizes developed-type pollution (PM2.5 / PM10>0.5) in the World Health Organization criteria. PM2.5 was dominated by SO42-, NO3-, and pseudo-carbonaceous compounds with obvious differences in concentrations and proportions between non-haze and haze episodes. The non-negative matrix factorization (NMF) analysis provided reasonable PM2.5 source profiles, by which five sources were identified: soil dust, traffic emission, biomass combustion, industrial emission, and coal combustion accounting for 13, 22, 12, 28, and 25  % of the total, respectively. The dust impact increased with northwesterlies during non-haze periods and decreased under stagnant conditions during haze periods. A blue alert of heavy air pollution was characterized by the greatest contribution from industrial emissions (61  %). During the Chinese Lantern Festival, an orange alert was issued and biomass combustion was found to be the major source owing to firework explosions. Red-alert haze was almost equally contributed by local traffic and transported coal combustion emissions from the vicinity of Beijing (approximately 40  % each) that was distinguished by the highest levels of NO3- and SO42-, respectively. This study also reveals that the severity and source of haze are largely dependent on meteorological conditions.

ENVIRONMENTAL APPLICATIONS OF NOVEL INSTRUMENTATION FOR MEASUREMENT OF LEAD ISOTOPE RATIOS IN ATMOSPHERIC POLLUTION SOURCE APPORTIONMENT STUDIES

EPA Science Inventory

In spite of the reduced flux of lead to the atmosphere from the combustion of leaded gasoline, anthropogenic sources still dominate the supply of lead to the atmosphere and the environment. Emissions from coal and oil combustion, industrial processes, and municipal incineration w...

Trends in multi-pollutant emissions from a technology-linked inventory for India: II. Residential, agricultural and informal industry sectors

NASA Astrophysics Data System (ADS)

Pandey, Apoorva; Sadavarte, Pankaj; Rao, Anand B.; Venkataraman, Chandra

2014-12-01

Dispersed traditional combustion technologies, characterized by inefficient combustion and significant emissions, are widely used in residential cooking and "informal industries" including brick production, food and agricultural product processing operations like drying and cooking operations related to sugarcane juice, milk, food-grain, jute, silk, tea and coffee. In addition, seasonal agricultural residue burning in field is a discontinuous source of significant emissions. Here we estimate fuel consumption in these sectors and agricultural residue burned using detailed technology divisions and survey-based primary data for 2010 and projected between 1996 and 2015. In the residential sector, a decline in the fraction of solid biomass users for cooking from 79% in 1996 to 65% in 2010 was offset by a growing population, leading to a nearly constant population of solid biomass users, with a corresponding increase in the population of LPG users. Emissions from agriculture followed the growth in agricultural production and diesel use by tractors and pumps. Trends in emissions from the informal industries sector followed those in coal combustion in brick kilns. Residential biomass cooking stoves were the largest contributors to emissions of PM2.5, OC, CO, NMVOC and CH4. Highest emitting technologies of BC were residential kerosene wick lamps. Emissions of SO2 were largely from coal combustion in Bull's trench kilns and other brick manufacturing technologies. Diesel use in tractors was the major source of NOx emissions. Uncertainties in emission estimates were principally from highly uncertain emission factors, particularly for technologies in the informal industries.

An overview of particulate emissions from residential biomass combustion

NASA Astrophysics Data System (ADS)

Vicente, E. D.; Alves, C. A.

2018-01-01

Residential biomass burning has been pointed out as one of the largest sources of fine particles in the global troposphere with serious impacts on air quality, climate and human health. Quantitative estimations of the contribution of this source to the atmospheric particulate matter levels are hard to obtain, because emission factors vary greatly with wood type, combustion equipment and operating conditions. Updated information should improve not only regional and global biomass burning emission inventories, but also the input for atmospheric models. In this work, an extensive tabulation of particulate matter emission factors obtained worldwide is presented and critically evaluated. Existing quantifications and the suitability of specific organic markers to assign the input of residential biomass combustion to the ambient carbonaceous aerosol are also discussed. Based on these organic markers or other tracers, estimates of the contribution of this sector to observed particulate levels by receptor models for different regions around the world are compiled. Key areas requiring future research are highlighted and briefly discussed.

[Inventory and environmental impact of VOCs emission from the typical anthropogenic sources in Sichuan province].

PubMed

Han, Li; Wang, Xing-Rui; He, Min; Guo, Wei-Guang

2013-12-01

Based on Sichuan province environmental statistical survey data and other relevant activity data, volatile organic compounds (VOCs) emissions from typical anthropogenic sources in Sichuan province were calculated for the year of 2011 by applying the emission factor method. Besides, ozone and secondary organic aerosol formation potentials of these typical anthropogenic sources were discussed. The total VOC emission from these sources was about 482 kt in Sichuan province, biomass burning, solvent utilization, industrial processes, storage and distribution of fuel, and fossil fuel combustion contributed 174 kt, 153 kt, 121 kt, 21 kt and 13 kt, respectively; architecture wall painting, furniture coating, wood decoration painting and artificial board were the major emission sectors of the solvent utilization; while for the industrial processes, 19.4% of VOCs emission was from the wine industry. Chengdu was the largest contributor compared to the other cities in Sichuan, whose VOCs emission from these typical anthropogenic sources in 2011 was 112 kt. OFP of these sources was 1,930 kt altogether. Solvent utilization contributed 50.5% of the total SOA formation potentials, biomass burning and industrial processes both contributed about 23% , with storage and distribution of fuel and fossil fuel combustion accounting for 1% and 1.4%, respectively.

40 CFR 98.32 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GREENHOUSE GAS REPORTING General Stationary Fuel Combustion Sources § 98.32 GHGs to report. You must report CO2, CH4, and N2O mass emissions from each stationary fuel combustion unit, except as otherwise...

40 CFR 98.32 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GREENHOUSE GAS REPORTING General Stationary Fuel Combustion Sources § 98.32 GHGs to report. You must report CO2, CH4, and N2O mass emissions from each stationary fuel combustion unit, except as otherwise...

40 CFR 98.32 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GREENHOUSE GAS REPORTING General Stationary Fuel Combustion Sources § 98.32 GHGs to report. You must report CO2, CH4, and N2O mass emissions from each stationary fuel combustion unit, except as otherwise...

40 CFR 98.32 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GREENHOUSE GAS REPORTING General Stationary Fuel Combustion Sources § 98.32 GHGs to report. You must report CO2, CH4, and N2O mass emissions from each stationary fuel combustion unit, except as otherwise...

Regional air pollution over Malaysia

NASA Astrophysics Data System (ADS)

Krysztofiak, G.; Catoire, V.; Dorf, M.; Grossmann, K.; Hamer, P. D.; Marécal, V.; Reiter, A.; Schlager, H.; Eckhardt, S.; Jurkat, T.; Oram, D.; Quack, B.; Atlas, E.; Pfeilsticker, K.

2012-12-01

During the SHIVA (Stratospheric Ozone: Halogen Impacts in a Varying Atmosphere) campaign in Nov. and Dec. 2011 a number of polluted air masses were observed in the marine and terrestrial boundary layer (0 - 2 km) and in the free troposphere (2 - 12 km) over Borneo/Malaysia. The measurements include isoprene, CO, CO2, CH4, N2O, NO2, SO2 as primary pollutants, O3 and HCHO as secondary pollutants, and meteorological parameters. This set of trace gases can be used to fingerprint different sources of local and regional air pollution (e.g., biomass burning and fossil fuel burning, gas flaring on oil rigs, emission of ships and from urban areas, volcanic emissions, and biogenic emissions). Individual sources and location can be identified when the measurements are combined with a nested-grid regional scale chemical and meteorological model and lagrangian particle dispersion model (e.g., CCATT-BRAMS and FLEXPART). In the case of the former, emission inventories of the primary pollutants provide the basis for the trace gas simulations. In this region, the anthropogenic influence on air pollution seems to dominate over natural causes. For example, CO2 and CH4 often show strong correlations with CO, suggesting biomass burning or urban fossil fuel combustion dominates the combustion sources. The study of the CO/CO2 and CH4/CO ratios can help separate anthropogenic combustion from biomass burning pollution sources. In addition, these ratios can be used as a measure of combustion efficiency to help place the type of biomass burning particular to this region within the wider context of fire types found globally. On several occasions, CH4 enhancements are observed near the ocean surface, which are not directly correlated with CO enhancements thus indicating a non-combustion-related CH4 source. Positive correlations between SO2 and CO show the anthropogenic influence of oil rigs located in the South China Sea. Furthermore, SO2 enhancements are observed without any increase in CO, indicating possible volcanic emissions from the Indonesian islands to the South and East and the Philippines to the North East. The regional pollution seems to be influenced by emissions from Singapore, Philippines, Indonesia and Peninsula Malaysia, and on occasion by anthropogenic emissions from Thailand, Vietnam, Australia, and China.

Nitrogen saturation in the Rocky Mountains: Linking emissions, deposition, and ecosystem effects using stable isotopes of nitrogen compounds

USGS Publications Warehouse

Campbell, D.H.; Nanus, L.; Böhlke, J.K.; Harlin, K.; Collett, J.

2007-01-01

Elevated levels of atmospheric N deposition are affecting terrestrial and aquatic ecosystems at high elevations in Rocky Mountain National Park and adjacent areas of the Front Range of Colorado. Federal and state agencies are now working together to develop cost-effective means for reducing atmospheric N deposition. A discussion on N saturation covers the need for better understanding of N emission source areas and source types that contribute to N deposition in the Rocky Mountains Front Range of Colorado; reductions in NO emissions that resulted from Clean Air Act Amendments, which caused NO3 deposition to decrease between 1984 and 2003; factors contributing to N deposition, e.g., rapid population growth and energy development; origins of NO3, e.g., as NO emissions from fossil fuel combustion, including stationary sources (e.g. emission from coal combustion in electric generating units), and mobile sources (vehicle emissions); disperse stationary sources from energy resource development, e.g., natural gas production; and the importance of incorporating local source characterization and finer spatial and temporal sampling into future studies, which could provide additional insight into N deposition source attribution. This is an abstract of a paper presented at the 100th Annual Conference and Exhibition of the Air and Waste Management Association (Pittsburgh, PA 6/26-29/2007).

A Global Emission Inventory of Black Carbon and Primary Organic Carbon from Fossil-Fuel and Biofuel Combustion

NASA Astrophysics Data System (ADS)

Bond, T. C.; Streets, D. G.; Nelson, S. M.

2001-12-01

Regional and global climate models rely on emission inventories of black carbon and organic carbon to determine the climatic effects of primary particulate matter (PM) from combustion. The emission of primary carbonaceous particles is highly dependent on fuel type and combustion practice. Therefore, simple categories such as "domestic" or "industrial" combustion are not sufficient to quantify emissions, and the black-carbon and organic-carbon fractions of PM vary with combustion type. We present a global inventory of primary carbonaceous particles that improves on previous "bottom-up" tabulations (e.g. \\textit{Cooke et al.,} 1999) by considering approximately 100 technologies, each representing one combination of fuel, combustion type, and emission controls. For fossil-fuel combustion, we include several categories not found in previous inventories, including "superemitting" and two-stroke vehicles, steel-making. We also include emissions from waste burning and biofuels used for heating and cooking. Open biomass burning is not included. Fuel use, drawn from International Energy Agency (IEA) and United Nations (UN) data, is divided into technologies on a regional basis. We suggest that emissions in developing countries are better characterized by including high-emitting technologies than by invoking emission multipliers. Due to lack of information on emission factors and technologies in use, uncertainties are high. We estimate central values and uncertainties by combining the range of emission factors found in the literature with reasonable estimates of technology divisions. We provide regional totals of central, low and high estimates, identify the sources of greatest uncertainty to be targeted for future work, and compare our results with previous emission inventories. Both central estimates and uncertainties are given on a 1\\deg x1\\deg grid. As we have reported previously for the case of China (\\textit{Streets et al.,} 2001), low-technology combustion contributes greatly to the emissions and to the uncertainties.

Emissions from small-scale energy production using co-combustion of biofuel and the dry fraction of household waste.

PubMed

Hedman, Björn; Burvall, Jan; Nilsson, Calle; Marklund, Stellan

2005-01-01

In sparsely populated rural areas, recycling of household waste might not always be the most environmentally advantageous solution due to the total amount of transport involved. In this study, an alternative approach to recycling has been tested using efficient small-scale biofuel boilers for co-combustion of biofuel and high-energy waste. The dry combustible fraction of source-sorted household waste was mixed with the energy crop reed canary-grass (Phalaris Arundinacea L.), and combusted in both a 5-kW pilot scale reactor and a biofuel boiler with 140-180 kW output capacity, in the form of pellets and briquettes, respectively. The chlorine content of the waste fraction was 0.2%, most of which originated from plastics. The HCl emissions exceeded levels stipulated in new EU-directives, but levels of equal magnitude were also generated from combustion of the pure biofuel. Addition of waste to the biofuel did not give any apparent increase in emissions of organic compounds. Dioxin levels were close to stipulated limits. With further refinement of combustion equipment, small-scale co-combustion systems have the potential to comply with emission regulations.

Gaseous emissions during concurrent combustion of biomass and non-recyclable municipal solid waste

PubMed Central

2011-01-01

Background Biomass and municipal solid waste offer sustainable sources of energy; for example to meet heat and electricity demand in the form of combined cooling, heat and power. Combustion of biomass has a lesser impact than solid fossil fuels (e.g. coal) upon gas pollutant emissions, whilst energy recovery from municipal solid waste is a beneficial component of an integrated, sustainable waste management programme. Concurrent combustion of these fuels using a fluidised bed combustor may be a successful method of overcoming some of the disadvantages of biomass (high fuel supply and distribution costs, combustion characteristics) and characteristics of municipal solid waste (heterogeneous content, conflict with materials recycling). It should be considered that combustion of municipal solid waste may be a financially attractive disposal route if a 'gate fee' value exists for accepting waste for combustion, which will reduce the net cost of utilising relatively more expensive biomass fuels. Results Emissions of nitrogen monoxide and sulphur dioxide for combustion of biomass are suppressed after substitution of biomass for municipal solid waste materials as the input fuel mixture. Interactions between these and other pollutants such as hydrogen chloride, nitrous oxide and carbon monoxide indicate complex, competing reactions occur between intermediates of these compounds to determine final resultant emissions. Conclusions Fluidised bed concurrent combustion is an appropriate technique to exploit biomass and municipal solid waste resources, without the use of fossil fuels. The addition of municipal solid waste to biomass combustion has the effect of reducing emissions of some gaseous pollutants. PMID:21284885

Characteristics and sensitivity analysis of multiple-time-resolved source patterns of PM2.5 with real time data using Multilinear Engine 2

NASA Astrophysics Data System (ADS)

Peng, Xing; Shi, Guo-Liang; Gao, Jian; Liu, Jia-Yuan; HuangFu, Yan-Qi; Ma, Tong; Wang, Hai-Ting; Zhang, Yue-Chong; Wang, Han; Li, Hui; Ivey, Cesunica E.; Feng, Yin-Chang

2016-08-01

With real time resolved data of Particulate matter (PM) and chemical species, understanding the source patterns and chemical characteristics is critical to establish controlling of PM. In this work, PM2.5 and chemical species were measured by corresponding online instruments with 1-h time resolution in Beijing. Multilinear Engine 2 (ME2) model was applied to explore the sources, and four sources (vehicle emission, crustal dust, secondary formation and coal combustion) were identified. To investigate the sensitivity of time resolution on the source contributions and chemical characteristics, ME2 was conducted with four time resolution runs (1-h, 2-h, 4-h, and 8-h). Crustal dust and coal combustion display large variation in the four time resolutions runs, with their contributions ranging from 6.7 to 10.4 μg m-3 and from 6.4 to 12.2 μg m-3, respectively. The contributions of vehicle emission and secondary formation range from 7.5 to 10.5 and from 14.7 to 16.7 μg m-3, respectively. The sensitivity analyses were conducted by principal component analysis-plot (PCA-plot), coefficient of divergence (CD), average absolute error (AAE) and correlation coefficients. For the four time resolution runs, the source contributions and profiles of crustal dust and coal combustion were more unstable than other source categories, possibly due to the lack of key markers of crustal dust and coal combustion (e.g. Si, Al). On the other hand, vehicle emission and crustal dust were more sensitive to time series of source contributions at different time resolutions. Findings in this study can improve our knowledge of source contributions and chemical characteristics at different time solutions.

40 CFR 60.1680 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2012 CFR

2012-07-01

... certification, who may operate the municipal waste combustion unit? 60.1680 Section 60.1680 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operator...

40 CFR 60.1680 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2011 CFR

2011-07-01

... certification, who may operate the municipal waste combustion unit? 60.1680 Section 60.1680 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operator...

40 CFR 60.1680 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2013 CFR

2013-07-01

... certification, who may operate the municipal waste combustion unit? 60.1680 Section 60.1680 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operator...

40 CFR 60.1680 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2014 CFR

2014-07-01

... certification, who may operate the municipal waste combustion unit? 60.1680 Section 60.1680 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operator...

40 CFR 60.1680 - After the required date for operator certification, who may operate the municipal waste...

Code of Federal Regulations, 2010 CFR

2010-07-01

... certification, who may operate the municipal waste combustion unit? 60.1680 Section 60.1680 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule-Good Combustion Practices: Operator...

Analyses of extracted biodiesel and petroleum diesel exhaust particle and the effects on endothelial cell toxicity and antioxidant response.

EPA Science Inventory

Biodiesel (BD) is a renewable energy source and is readily substituted in diesel engines. Combustion of biodiesel is cleaner due to the efficiency of the fuel to completely combust. Biodiesel combustion emissions contain less CO, PAHs, aldehydes, and particulate matter (PM) mas...

Temporal variability of Polycyclic Aromatic Hydrocarbons (PAHs) in a receptor site of the Puebla-Tlaxcala Valley

NASA Astrophysics Data System (ADS)

Padilla, Z. V.; Torres, R.; Ruiz Suarez, L.; Molina, L. T.

2013-05-01

This contribution documents the presence and possible origin of PAHs, their temporal concentration patterns and correlations with other air pollutants in the so-called Puebla-Tlaxcala valley. This valley is located to the east of the Mexico City Metropolitan Area and is a very populated region which suffers of air pollution problems. Emission sources of PAHs include open burning, industrial boilers, automobiles and trucks, but vehicle emissions vary significantly depending on the use of: fuel, engine type and catalytic converter. An important emission source in the Puebla-Tlaxcala region is wood burning for cooking. Therefore, it is expected to have contributions of PAHS from this type of sources. PAHs measurements were performed in an air pollution semi-rural receptor site (Chipilo) southwest the City of Puebla, using an aerosol photoelectric sensor (PAS 2000 CE) to measure the concentration of PAHs and a diffuser charger (DC 2000 CE) to evaluate the active surface (DC) of the particles. The measuring period included March and April of 2012 during the ozne season in central Mexico. The use of these two sensors in parallel has been identified as a fingerprint technique to identify different types of particles from several combustion processes and is a useful tool to identify quantitatively the major source of emissions, as well as to describe thephysical and chemical characteristics of the particles. Correlations between PAHs and DC, with NOx and CO, together with an analysis of atmospheric transport may approximate the possible origin of these particles. The coefficient PAHs / DC associated with backward trajectory analysis represents a tool to identify potential areas of emission. The correlation between PAHs and NOx emissions reflects association with diesel combustion, while the correlation between PAHs and CO, the combustion of gasoline. The results show that vehicle emissions are the major source of PAHs with an associated increase in the concentration of PAHs in the morning, when there is more vehicular traffic. The time series of PAHs also exhibit synchronized peaks of PAHs and DC that correspond to hours of traffic which shows the relationship of PAHs with DC. However, correlations of PAHs with DC show a relatively strong scattering suggesting that aerosols are a mixture of particles of different sources and different ages. Throughout the day is observed the aging of primary combustion particles due to the secondary aerosols coating. This coating may prolong the life time of the PAHs in the atmosphere. Also occurs a decrease in the ratio PAHs / DC during the day. Low ratios indicate the abundance of large particles, whereas high ratios indicate abundance dominated by small particle emissions from diesel engines. The resulting correlations show a significant linear trend evolution of PAHs with NOx, indicating that the PAHs are associated with the combustion of diesel, and a linear trend of PAHs with DC for each type of aerosol combustion, while the correlation of PAHs with CO results in an exponential trend which implies that PAHs are related to the combustion of diesel.

Alternative energy balances for Bulgaria to mitigate climate change

NASA Astrophysics Data System (ADS)

Christov, Christo

1996-01-01

Alternative energy balances aimed to mitigate greenhouse gas (GHG) emissions are developed as alternatives to the baseline energy balance. The section of mitigation options is based on the results of the GHG emission inventory for the 1987 1992 period. The energy sector is the main contributor to the total CO2 emissions of Bulgaria. Stationary combustion for heat and electricity production as well as direct end-use combustion amounts to 80% of the total emissions. The parts of the energy network that could have the biggest influence on GHG emission reduction are identified. The potential effects of the following mitigation measures are discussed: rehabilitation of the combustion facilities currently in operation; repowering to natural gas; reduction of losses in thermal and electrical transmission and distribution networks; penetration of new combustion technologies; tariff structure improvement; renewable sources for electricity and heat production; wasteheat utilization; and supply of households with natural gas to substitute for electricity in space heating and cooking. The total available and the achievable potentials are estimated and the implementation barriers are discussed.

40 CFR 60.1640 - What must I do if I plan to permanently close my municipal waste combustion unit and not restart it?

Code of Federal Regulations, 2013 CFR

2013-07-01

... close my municipal waste combustion unit and not restart it? 60.1640 Section 60.1640 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... do if I plan to permanently close my municipal waste combustion unit and not restart it? (a) If you...

40 CFR 60.1640 - What must I do if I plan to permanently close my municipal waste combustion unit and not restart it?

Code of Federal Regulations, 2012 CFR

2012-07-01

... close my municipal waste combustion unit and not restart it? 60.1640 Section 60.1640 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... do if I plan to permanently close my municipal waste combustion unit and not restart it? (a) If you...

40 CFR 60.1640 - What must I do if I plan to permanently close my municipal waste combustion unit and not restart it?

Code of Federal Regulations, 2014 CFR

2014-07-01

... close my municipal waste combustion unit and not restart it? 60.1640 Section 60.1640 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... do if I plan to permanently close my municipal waste combustion unit and not restart it? (a) If you...

40 CFR 60.1640 - What must I do if I plan to permanently close my municipal waste combustion unit and not restart it?

Code of Federal Regulations, 2011 CFR

2011-07-01

... close my municipal waste combustion unit and not restart it? 60.1640 Section 60.1640 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... do if I plan to permanently close my municipal waste combustion unit and not restart it? (a) If you...

40 CFR 60.1640 - What must I do if I plan to permanently close my municipal waste combustion unit and not restart it?

Code of Federal Regulations, 2010 CFR

2010-07-01

... close my municipal waste combustion unit and not restart it? 60.1640 Section 60.1640 Protection of... NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion... do if I plan to permanently close my municipal waste combustion unit and not restart it? (a) If you...

CONTROLLING NOX EMISSION FROM INDUSTRIAL SOURCES

EPA Science Inventory

A number of regulatory actions focused on reducing NO_x emissions from stationary combustion sources have been taken in the United States in the last decade. These actions include the Acid Rain NO_x regulations, the Ozone Transport Commission's NO_x ...

THE IMPACT OF PARTICULATE EMISSIONS CONTROL ON THE CONTROL OF OTHER MWC AIR EMISSIONS

EPA Science Inventory

On December 20, 1989, the Environmental Protection Agency (EPA) proposed revised new source performance standards for new municipal waste combustion (MWC) units and guidelines for existing sources. The proposed national regulations require tighter particulate matter control and a...

The new open Flexible Emission Inventory for Greece and the Greater Athens Area (FEI-GREGAA): Account of pollutant sources and their importance from 2006 to 2012

NASA Astrophysics Data System (ADS)

Fameli, Kyriaki-Maria; Assimakopoulos, Vasiliki D.

2016-07-01

Photochemical and particulate pollution problems persist in Athens as they do in various European cities, despite measures taken. Although, for many cities, organized and updated pollutant emissions databases exist, as well as infrastructure for the support of policy implementation, this is not the case for Greece and Athens. So far abstract efforts to create inventories from temporal and spatial annual low resolution data have not lead to the creation of a useful database. The objective of this study was to construct an emission inventory in order to examine the emission trends in Greece and the Greater Athens Area for the period 2006-2012 on a spatial scale of 6 × 6 km2 and 2 × 2 km2, respectively and on a temporal scale of 1 h. Emissions were calculated from stationary combustion sources, transportation (road, navigation and aviation), agriculture and industry obtained from official national and European sources. Moreover, new emission factors were calculated for road transport and aviation. The final database named F.E.I. - GREGAA (Flexible Emission Inventory for GREece and the GAA) is open-structured so as to receive data updates, new pollutants, various emission scenarios and/or different emission factors and be transformed for any grid spacing. Its main purpose is to be used in applications with photochemical models to contribute to the investigation on the type of sources and activities that lead to the configuration of air quality. Results showed a decreasing trend in CO, NOx and VOCs-NMVOCs emissions and an increasing trend from 2011 onwards in PM10 emissions. Road transport and small combustion contribute most to CO emissions, road transport and navigation to NOx and small combustion and industries to PM10. The onset of the economic crisis can be seen from the reduction of emissions from industry and the increase of biomass burning for heating purposes.

Receptor modeling for source apportionment of polycyclic aromatic hydrocarbons in urban atmosphere.

PubMed

Singh, Kunwar P; Malik, Amrita; Kumar, Ranjan; Saxena, Puneet; Sinha, Sarita

2008-01-01

This study reports source apportionment of polycyclic aromatic hydrocarbons (PAHs) in particulate depositions on vegetation foliages near highway in the urban environment of Lucknow city (India) using the principal components analysis/absolute principal components scores (PCA/APCS) receptor modeling approach. The multivariate method enables identification of major PAHs sources along with their quantitative contributions with respect to individual PAH. The PCA identified three major sources of PAHs viz. combustion, vehicular emissions, and diesel based activities. The PCA/APCS receptor modeling approach revealed that the combustion sources (natural gas, wood, coal/coke, biomass) contributed 19-97% of various PAHs, vehicular emissions 0-70%, diesel based sources 0-81% and other miscellaneous sources 0-20% of different PAHs. The contributions of major pyrolytic and petrogenic sources to the total PAHs were 56 and 42%, respectively. Further, the combustion related sources contribute major fraction of the carcinogenic PAHs in the study area. High correlation coefficient (R2 > 0.75 for most PAHs) between the measured and predicted concentrations of PAHs suggests for the applicability of the PCA/APCS receptor modeling approach for estimation of source contribution to the PAHs in particulates.

Urbanization-related changes in soil PAHs and potential health risks of emission sources in a township in Southern Jiangsu, China.

PubMed

Cao, Hongbin; Chao, Sihong; Qiao, Li; Jiang, Yanxue; Zeng, Xiancai; Fan, Xiaoting

2017-01-01

Urbanization, which is characterized by population aggregation, industrial development, and increased traffic load, may change local polycyclic aromatic hydrocarbons (PAH) emissions and their associated health risks. To investigate these changes, we collected soil samples in 2009 and 2014 in a rapidly developing small town in Southern Jiangsu (China) and measured the concentrations of 16 PAHs via gas chromatography-mass spectrometry. Although the total PAHs decreased from 4586.6 to 640.6ng/g, the concentrations of the high-molecular-weight PAHs benzo(b)fluoranthene and benzo(a)pyrene increased due to changes in the PAH sources. Source apportionment by positive matrix factorization indicated that the two sources responsible for the highest soil PAH contributions changed from biomass combustion (42%) and coal combustion (32%) in 2009 to coal, biomass and natural gas combustion (35%) and diesel combustion (33%) in 2014. However, the two sources with the highest associated health risks were diesel and gasoline combustion in both years. The incremental lifetime cancer risk for residents exposed to PAHs in the soil via incidental ingestion and dermal contact decreased from 1.75×10 -6 to 1.60×10 -6 . The ban on open burning of straw and the substitution of coal with natural gas offset the PAH health risks due to increased urbanization. Copyright © 2016 Elsevier B.V. All rights reserved.

Comparative toxicity and mutagenicity of soy-biodiesel and petroleum-diesel emissions: overview of studies from the U.S. EPA, Research Triangle Park, NC.

PubMed

Madden, Michael C

2015-01-01

Biodiesel use as a fuel is increasing globally as an alternate to petroleum sources. To comprehensively assess the effects of the use of biodiesel as an energy source, end stage uses of biodiesel such as the effects of inhalation of combusted products on human health must be incorporated. To date, few reports concerning the toxicological effects of the emissions of combusted biodiesel or blends of biodiesel on surrogates of health effects have been published. The relative toxicity of the combusted biodiesel emissions compared to petroleum diesel emissions with short term exposures is also not well known. To address the paucity of findings on the toxicity of combusted biodiesel emissions, studies were undertaken at the U.S. Environmental Protection Agency laboratories in Research Triangle Park, North Carolina. The studies used a variety of approaches with nonhuman animal models to examine biological responses of the lung and cardiovascular systems induced by acute and repeated exposures to pure biodiesel and biodiesel blended with petroleum diesel. Effects of the emissions on induction of mutations in bacterial test strains and mammalian DNA adducts were also characterized and normalized to engine work load. The emissions were characterized as to the physicochemical composition in order to determine the magnitude of the differences among the emissions utilized in the studies. This article summarizes the major finding of these studies which are contained within this special issue of Inhalation Toxicology. The findings provided in these articles provide information about the toxicity of biodiesel emissions relative to petroleum diesel emissions and which can be utilized in a life cycle analyses of the effects of increased biodiesel usage.

Size-resolved trace metal characterization of aerosols emitted by four important source types in Switzerland

NASA Astrophysics Data System (ADS)

Buerki, Peter R.; Gaelli, Brigitte C.; Nyffeler, Urs P.

In central Switzerland five types of emission sources are mainly responsible for airborne trace metals: traffic, industrial plants burning heavy oil, resuspension of soil particles, residential heatings and refuse incineration plants. The particulate emissions of each of these source types except refuse incineration were sampled using Berner impactors and the mass and elemental size distributions of Cd, Cu, Mn, Pb, Zn, As and Na determined. Cd, Na and Zn are not characteristic for any of these source types. As and Cu, occurring in the fine particle fractions are characteristic for heavy oil combustion, Mn for soil dust and sometimes for heavy and fuel oil combustion and Pb for traffic aerosols. The mass size distributions of aerosols originating from erosion and abrasion processes show a maximum mass fraction in the coarse particle range larger than about 1 μm aerodynamic equivalent diameters (A.E.D.). Aerosols originating from combustion processes show a second maximum mass fraction in the fine particle range below about 0.5μm A.E.D. Scanning electron microscopy combined with an EDS analyzer was used for the morphological characterization of emission and ambient aerosols.

Control of NOx Emissions from Stationary Combustion Sources

EPA Science Inventory

In general, NOx control technologies are categorized as being either primary control technologies or secondary control technologies. Primary control technologies reduce the formation of NOx in the primary combustion zone. In contrast, secondary control technologies destroy the NO...

MERCURY CONTROL FOR COAL-FIRED POWER PLANTS

EPA Science Inventory

There are many sources of natural and anthropogenic mercury emissions, but combustion of coal is known to be the major anthropogenic source of mercury (Hg) emissions in the U.S. and world wide. To address this, EPA has recently promulgated the Clean Air Mercury Rule to reduce Hg ...

Can positive matrix factorization help to understand patterns of organic trace gases at the continental Global Atmosphere Watch site Hohenpeissenberg?

NASA Astrophysics Data System (ADS)

Leuchner, M.; Gubo, S.; Schunk, C.; Wastl, C.; Kirchner, M.; Menzel, A.; Plass-Dülmer, C.

2015-02-01

From the rural Global Atmosphere Watch (GAW) site Hohenpeissenberg in the pre-alpine area of southern Germany, a data set of 24 C2-C8 non-methane hydrocarbons over a period of 7 years was analyzed. Receptor modeling was performed by positive matrix factorization (PMF) and the resulting factors were interpreted with respect to source profiles and photochemical aging. Differing from other studies, no direct source attribution was intended because, due to chemistry along transport, mass conservation from source to receptor is not given. However, at remote sites such as Hohenpeissenberg, the observed patterns of non-methane hydrocarbons can be derived from combinations of factors determined by PMF. A six-factor solution showed high stability and the most plausible results. In addition to a biogenic and a background factor of very stable compounds, four additional anthropogenic factors were resolved that could be divided into two short- and two long-lived patterns from evaporative sources/natural gas leakage and incomplete combustion processes. The volume or mass contribution at the site over the entire period was, in decreasing order, from the following factor categories: background, gas leakage and long-lived evaporative, residential heating and long-lived combustion, short-lived evaporative, short-lived combustion, and biogenic. The importance with respect to reactivity contribution was generally in reverse order, with the biogenic and the short-lived combustion factors contributing most. The seasonality of the factors was analyzed and compared to results of a simple box model using constant emissions and the photochemical decay calculated from the measured annual cycles of OH radicals and ozone. Two of the factors, short-lived combustion and gas leakage/long-lived evaporative, showed winter/summer ratios of about 9 and 7, respectively, as expected from constant source estimations. Contrarily, the short-lived evaporative emissions were about 3 times higher in summer than in winter, while residential heating/long-lived combustion emissions were about 2 times higher in winter than in summer.

Reducing mortality risk by targeting specific air pollution sources: Suva, Fiji.

PubMed

Isley, C F; Nelson, P F; Taylor, M P; Stelcer, E; Atanacio, A J; Cohen, D D; Mani, F S; Maata, M

2018-01-15

Health implications of air pollution vary dependent upon pollutant sources. This work determines the value, in terms of reduced mortality, of reducing ambient particulate matter (PM 2.5 : effective aerodynamic diameter 2.5μm or less) concentration due to different emission sources. Suva, a Pacific Island city with substantial input from combustion sources, is used as a case-study. Elemental concentration was determined, by ion beam analysis, for PM 2.5 samples from Suva, spanning one year. Sources of PM 2.5 have been quantified by positive matrix factorisation. A review of recent literature has been carried out to delineate the mortality risk associated with these sources. Risk factors have then been applied for Suva, to calculate the possible mortality reduction that may be achieved through reduction in pollutant levels. Higher risk ratios for black carbon and sulphur resulted in mortality predictions for PM 2.5 from fossil fuel combustion, road vehicle emissions and waste burning that surpass predictions for these sources based on health risk of PM 2.5 mass alone. Predicted mortality for Suva from fossil fuel smoke exceeds the national toll from road accidents in Fiji. The greatest benefit for Suva, in terms of reduced mortality, is likely to be accomplished by reducing emissions from fossil fuel combustion (diesel), vehicles and waste burning. Copyright © 2017. Published by Elsevier B.V.

Historical record of lead accumulation and source in the tidal flat of Haizhou Bay, Yellow Sea: Insights from lead isotopes.

PubMed

Zhang, Rui; Guan, Minglei; Shu, Yujie; Shen, Liya; Chen, Xixi; Zhang, Fan; Li, Tiegang

2016-05-15

In order to investigate the historical records of lead contamination and source in coastal region of Haizhou Bay, Yellow Sea, a sediment core was collected from tidal flat, dated by (210)Pb and (137)Cs. Lead and its stable isotopic ratios were determined. The profiles of enrichment factor (EF) and Pb isotope ratios showed increasing trend upward throughout the core, correlating closely with the experience of a rapid economic and industrial development of the catchment. According to Pb isotopic ratios, coal combustion emission mainly contributed to the Pb burden in sediments. Based on end-member model, coal combustion emission dominated anthropogenic Pb sources in recent decades contributing from 48% to 67% in sediment. And the contribution of leaded gasoline was lower than 20%. A stable increase of coal combustion source was found in sediment core, while the contribution of leaded gasoline had declined recently, with the phase-out of leaded gasoline in China. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mercury in municipal solid wastes and New Jersey mercury prevention and reduction program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erdogan, H.; Stevenson, E.

1994-12-31

Mercury is a very toxic heavy metal which accumulates in the brain causing neurological damages involving psychasthenic and vegetative syndrome. At high exposure levels it causes behavioral and personality changes, loss of memory and insomnia. Long-term exposure or exposure during pregnancy to mercury or mercury compounds can permanently damage the kidney and fetus. In addition to potential effects on human health, mercury poisoning can also affect other living organisms. Mercury is different than other heavy metals. It consistently biomagnifies and bioaccumulates within the aquatic food chain. Global sources of mercury release are both natural and anthropogenic. Natural sources include volatilizationmore » of gaseous-mercury iron soils ana rocks, volcanic releases, evaporation from the ocean and other water bodies. Anthropogenic sources are fuel and coal combustion, mining, smelting, manufacturing activities, disposal of sludge, pesticides, animal and food waste, and incineration of municipal solid waste. Worldwide combustion of municipal solid waste is the second largest source of atmospheric emission of mercury. In New Jersey, incineration of solid waste is the largest source of atmospheric emission of mercury. The New Jersey Department of Environmental Protection and Energy (NJDEPE) has developed a comprehensive program to control and prevent emission of mercury resulting from combustion municipal solid waste.« less

Air Quality and Stationary Source Emission Control; Committee on Public Works, Senate, Ninety-Fourth Congress, First Session. [Committee Print.

ERIC Educational Resources Information Center

National Academy of Sciences - National Research Council, Washington, DC.

This report reviews the problems of sulfur oxide emissions and nitrogen oxide emissions from stationary sources. The first part of the report discusses the adverse consequences to health from combustion of sulfur-containing fossil fuels. The health problem is discussed by relating sulfur oxide levels and respirable particulate matter with…

The effect of emission from coal combustion in nonindustrial sources on deposition of sulfur and oxidized nitrogen in Poland.

PubMed

Kryza, Maciej; Werner, Małgorzata; Błaś, Marek; Dore, Anthony J; Sobik, Mieczysław

2010-07-01

Poland has one of the largest sulfur and nitrogen emissions in Europe. This is mainly because coal is a main fuel in industrial and nonindustrial combustion. The aim of this paper is to assess the amount of sulfur and nitrogen deposited from SNAP sector 02 (nonindustrial sources) coal combustion. To assess this issue, the Fine Resolution Atmospheric Multipollutant Exchange (FRAME) model was used. The results suggest that industrial combustion has the largest impact on deposition of oxidized sulfur, whereas the oxidized nitrogen national deposition budget is dominated by transboundary transport. The total mass of pollutants deposited in Poland, originating from nonindustrial coal combustion, is 45 Gg of sulfur and 2.5 Gg of nitrogen, which is over 18% of oxidized sulfur and nearly 2% of oxidized nitrogen deposited. SNAP 02 is responsible for up to 80% of dry-deposited sulfur and 11% of nitrogen. The contribution to wet deposition is largest in central Poland in the case of sulfur and in some areas can exceed 11%. For oxidized nitrogen, nonindustrial emissions contribute less than 1% over the whole area of Poland. The switch from coal to gas fuel in this sector will result in benefits in sulfur and nitrogen deposition reduction.

Application of positive matrix factorization to identify potential sources of PAHs in soil of Dalian, China.

PubMed

Wang, Degao; Tian, Fulin; Yang, Meng; Liu, Chenlin; Li, Yi-Fan

2009-05-01

Soil derived sources of polycyclic aromatic hydrocarbons (PAHs) in the region of Dalian, China were investigated using positive matrix factorization (PMF). Three factors were separated based on PMF for the statistical investigation of the datasets both in summer and winter. These factors were dominated by the pattern of single sources or groups of similar sources, showing seasonal and regional variations. The main sources of PAHs in Dalian soil in summer were the emissions from coal combustion average (46%), diesel engine (30%), and gasoline engine (24%). In winter, the main sources were the emissions from coal-fired boiler (72%), traffic average (20%), and gasoline engine (8%). These factors with strong seasonality indicated that coal combustion in winter and traffic exhaust in summer dominated the sources of PAHs in soil. These results suggested that PMF model was a proper approach to identify the sources of PAHs in soil.

Characterizing and sourcing ambient PM2.5 over key emission regions in China III: Carbon isotope based source apportionment of black carbon

NASA Astrophysics Data System (ADS)

Yu, Kuangyou; Xing, Zhenyu; Huang, Xiaofeng; Deng, Junjun; Andersson, August; Fang, Wenzheng; Gustafsson, Örjan; Zhou, Jiabin; Du, Ke

2018-03-01

Regional haze over China has severe implications for air quality and regional climate. To effectively combat these effects the high uncertainties regarding the emissions from different sources needs to be reduced. In this paper, which is the third in a series on the sources of PM2.5 in pollution hotspot regions of China, we focus on the sources of black carbon aerosols (BC), using carbon isotope signatures. Four-season samples were collected at two key locations: Beijing-Tianjin-Hebei (BTH, part of Northern China plain), and the Pearl River Delta (PRD). We find that that fossil fuel combustion was the predominant source of BC in both BTH and PRD regions, accounting for 75 ± 5%. However, the contributions of what fossil fuel components were dominating differed significantly between BTH and PRD, and varied dramatically with seasons. Coal combustion is overall the all-important BC source in BTH, accounting for 46 ± 12% of the BC in BTH, with the maximum value (62%) found in winter. In contrast for the PRD region, liquid fossil fuel combustion (e.g., oil, diesel, and gasoline) is the dominant source of BC, with an annual mean value of 41 ± 15% and the maximum value of 55% found in winter. Region- and season-specific source apportionments are recommended to both accurately assess the climate impact of carbonaceous aerosol emissions and to effectively mitigate deteriorating air quality caused by carbonaceous aerosols.

BC measurement activities at the U.S. Environmental Protection Agency

EPA Science Inventory

Black carbon (BC)--sometimes referred to as soot, char, or elemental carbon (EC)--is a refractory form of light-absorbing carbon produced from incomplete combustion. Accurate measurement of BC in combustion source emissions is important for understanding anthropogenic climate for...

Emissions from fireplace and woodstove combustion of prevalent Portuguese woods

NASA Astrophysics Data System (ADS)

Alves, Célia

2010-05-01

P. Fernandes, C. Gonçalves, C.A. Alves, L. Tarelho, F. Mirante, T. Nunes and C. Pio Centre for Environmental and Marine Studies, Department of Environment, University of Aveiro, 3810-193 Aveiro, Portugal In Portugal, it was estimated that around 390000 ton/year of wood is burned in fireplaces, although the chemical characterisation of emission profiles has not yet been performed. Emission inventories and source apportionment, photochemistry and climate change models use values obtained for American or Alpine wood-fuels, uncommon in South Europe. Previous work has suggested that the species of wood used can have a huge influence on the particle emissions. Since the distribution of compounds emitted differs by species and burning conditions and there are many variations among published profiles, it is desirable to obtain specific data at a regional level on the chemical characterisation of wood smoke. A series of source tests was performed to compare the emission profiles from the woodstove combustion to those of fireplaces. Eight types of biomass were burned in the laboratory: seven species of wood grown in Portugal (Pinus pinaster, Eucalyptus globulus, Quercus suber, Acacia longifolia, Quercus faginea, Olea europea, Quercus ilex rotundifolia), and briquettes of biomass residues. The gas sampling was carried out in the exhaust ducts of both combustion systems. The collection of particles (PM2.5) was conducted in the dilution tunnel that was directly coupled to the chimney. Dilution sampling was used to characterise fine particle emissions from the combustion sources because it simulates the rapid cooling and dilution that occurs as exhaust mixes with the atmosphere. During each burning cycle, the concentrations of O2, CO2 and CO, as well as operational parameters (e.g. temperatures, flows, etc.), were automatically monitored. The PM2.5 samples were analysed by a thermal optical technique in order to obtain their organic carbon (OC) and elemental carbon (EC) content. It has been observed that fireplace emissions are higher than those of stoves. The emission factors were in the ranges 43 - 149 g CO/kg, 326 - 2699 g CO2/kg, 3 - 25 g PM2.5/kg, 1.34 - 12.0 g OC/kg and 0.16 - 1.25 g EC/kg of biomass burned on a dry basis. Very significant differences among emission factors for the different combusted wood species have not been registered.

Why models struggle to capture Arctic Haze: the underestimated role of gas flaring and domestic combustion emissions

NASA Astrophysics Data System (ADS)

Stohl, A.; Klimont, Z.; Eckhardt, S.; Kupiainen, K.

2013-04-01

Arctic Haze is a seasonal phenomenon with high concentrations of accumulation-mode aerosols occurring in the Arctic in winter and early spring. Chemistry transport models and climate chemistry models struggle to reproduce this phenomenon, and this has recently prompted changes in aerosol removal schemes to remedy the modeling problems. In this paper, we show that shortcomings in current emission data sets are at least as important. We perform a 3 yr model simulation of black carbon (BC) with the Lagrangian particle dispersion model FLEXPART. The model is driven with a new emission data set which includes emissions from gas flaring. While gas flaring is estimated to contribute less than 3% of global BC emissions in this data set, flaring dominates the estimated BC emissions in the Arctic (north of 66° N). Putting these emissions into our model, we find that flaring contributes 42% to the annual mean BC surface concentrations in the Arctic. In March, flaring even accounts for 52% of all Arctic BC near the surface. Most of the flaring BC remains close to the surface in the Arctic, so that the flaring contribution to BC in the middle and upper troposphere is small. Another important factor determining simulated BC concentrations is the seasonal variation of BC emissions from domestic combustion. We have calculated daily domestic combustion emissions using the heating degree day (HDD) concept based on ambient air temperature and compare results from model simulations using emissions with daily, monthly and annual time resolution. In January, the Arctic-mean surface concentrations of BC due to domestic combustion emissions are 150% higher when using daily emissions than when using annually constant emissions. While there are concentration reductions in summer, they are smaller than the winter increases, leading to a systematic increase of annual mean Arctic BC surface concentrations due to domestic combustion by 68% when using daily emissions. A large part (93%) of this systematic increase can be captured also when using monthly emissions; the increase is compensated by a decreased BC burden at lower latitudes. In a comparison with BC measurements at six Arctic stations, we find that using daily-varying domestic combustion emissions and introducing gas flaring emissions leads to large improvements of the simulated Arctic BC, both in terms of mean concentration levels and simulated seasonality. Case studies based on BC and carbon monoxide (CO) measurements from the Zeppelin observatory appear to confirm flaring as an important BC source that can produce pollution plumes in the Arctic with a high BC/CO enhancement ratio, as expected for this source type. Our results suggest that it may not be "vertical transport that is too strong or scavenging rates that are too low" and "opposite biases in these processes" in the Arctic and elsewhere in current aerosol models, as suggested in a recent review article (Bond et al., 2013), but missing emission sources and lacking time resolution of the emission data that are causing opposite model biases in simulated BC concentrations in the Arctic and in the mid-latitudes.

Sources of atmospheric ammonia

NASA Technical Reports Server (NTRS)

Harriss, R. C.; Michaels, J. T.

1982-01-01

The information available on factors that influence emissions from the principal societal sources of ammonia to the atmosphere, namely combustion processes, volatilization of farm animal wastes, and volatilization of fertilizers, is reviewed. Emission factors are established for each major source of atmospheric ammonia. The factors are then multiplied by appropriate source characterization descriptors to obtain calculated fluxes of ammonia to the atmosphere on a state-by-state basis for the United States.

Fluids and Combustion Facility Acoustic Emissions Controlled by Aggressive Low-Noise Design Process

NASA Technical Reports Server (NTRS)

Cooper, Beth A.; Young, Judith A.

2004-01-01

The Fluids and Combustion Facility (FCF) is a dual-rack microgravity research facility that is being developed by Northrop Grumman Information Technology (NGIT) for the International Space Station (ISS) at the NASA Glenn Research Center. As an on-orbit test bed, FCF will host a succession of experiments in fluid and combustion physics. The Fluids Integrated Rack (FIR) and the Combustion Integrated Rack (CIR) must meet ISS acoustic emission requirements (ref. 1), which support speech communication and hearing-loss-prevention goals for ISS crew. To meet these requirements, the NGIT acoustics team implemented an aggressive low-noise design effort that incorporated frequent acoustic emission testing for all internal noise sources, larger-scale systems, and fully integrated racks (ref. 2). Glenn's Acoustical Testing Laboratory (ref. 3) provided acoustical testing services (see the following photograph) as well as specialized acoustical engineering support as part of the low-noise design process (ref. 4).

Experimental Investigation of Fuel-Reactivity Controlled Compression Ignition (RCCI) Combustion Mode in a Multi-Cylinder, Light-Duty Diesel Engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cho, Kukwon; Curran, Scott; Prikhodko, Vitaly Y

2011-01-01

An experimental study was performed to provide the combustion and emission characteristics resulting from fuel-reactivity controlled compression ignition (RCCI) combustion mode utilizing dual-fuel approach in a light-duty, multi-cylinder diesel engine. In-cylinder fuel blending using port fuel injection of gasoline before intake valve opening (IVO) and early-cycle, direct injection of diesel fuel was used as the charge preparation and fuel blending strategy. In order to achieve the desired auto-ignition quality through the stratification of the fuel-air equivalence ratio ( ), blends of commercially available gasoline and diesel fuel were used. Engine experiments were performed at an engine speed of 2300rpm andmore » an engine load of 4.3bar brake mean effective pressure (BMEP). It was found that significant reduction in both nitrogen oxide (NOx) and particulate matter (PM) was realized successfully through the RCCI combustion mode even without applying exhaust gas recirculation (EGR). However, high carbon monoxide (CO) and hydrocarbon (HC) emissions were observed. The low combustion gas temperature during the expansion and exhaust processes seemed to be the dominant source of high CO emissions in the RCCI combustion mode. The high HC emissions during the RCCI combustion mode could be due to the increased combustion quenching layer thickness as well as the -stratification at the periphery of the combustion chamber. The slightly higher brake thermal efficiency (BTE) of the RCCI combustion mode was observed than the other combustion modes, such as the conventional diesel combustion (CDC) mode, and single-fuel, premixed charge compression ignition (PCCI) combustion mode. The parametric study of the RCCI combustion mode revealed that the combustion phasing and/or the peak cylinder pressure rise rate of the RCCI combustion mode could be controlled by several physical parameters premixed ratio (rp), intake swirl intensity, and start of injection (SOI) timing of directly injected fuel unlike other low temperature combustion (LTC) strategies.« less

40 CFR Appendix A-4 to Part 60 - Test Methods 6 through 10B

Code of Federal Regulations, 2010 CFR

2010-07-01

... sources Method 6A—Determination of sulfur dioxide, moisture, and carbon dioxide emissions from fossil fuel... fossil fuel combustion sources Method 6C—Determination of Sulfur Dioxide Emissions From Stationary... with SO2 to form particulate sulfite and by reacting with the indicator. If free ammonia is present...

40 CFR Appendix A-4 to Part 60 - Test Methods 6 through 10B

Code of Federal Regulations, 2011 CFR

2011-07-01

... sources Method 6A—Determination of sulfur dioxide, moisture, and carbon dioxide emissions from fossil fuel... fossil fuel combustion sources Method 6C—Determination of Sulfur Dioxide Emissions From Stationary... with SO2 to form particulate sulfite and by reacting with the indicator. If free ammonia is present...

40 CFR Appendix A-4 to Part 60 - Test Methods 6 through 10B

Code of Federal Regulations, 2013 CFR

2013-07-01

... sources Method 6A—Determination of sulfur dioxide, moisture, and carbon dioxide emissions from fossil fuel... fossil fuel combustion sources Method 6C—Determination of Sulfur Dioxide Emissions From Stationary... with SO2 to form particulate sulfite and by reacting with the indicator. If free ammonia is present...

40 CFR Appendix A-4 to Part 60 - Test Methods 6 through 10B

Code of Federal Regulations, 2014 CFR

2014-07-01

... sources Method 6A—Determination of sulfur dioxide, moisture, and carbon dioxide emissions from fossil fuel... fossil fuel combustion sources Method 6C—Determination of Sulfur Dioxide Emissions From Stationary... reacting with SO2 to form particulate sulfite and by reacting with the indicator. If free ammonia is...

40 CFR Appendix A-4 to Part 60 - Test Methods 6 through 10B

Code of Federal Regulations, 2012 CFR

2012-07-01

... sources Method 6A—Determination of sulfur dioxide, moisture, and carbon dioxide emissions from fossil fuel... fossil fuel combustion sources Method 6C—Determination of Sulfur Dioxide Emissions From Stationary... with SO2 to form particulate sulfite and by reacting with the indicator. If free ammonia is present...

Improved Leach Testing for Evaluating Fate of Mercury and Other Metals from Management of Coal Combustion Residues

EPA Science Inventory

Coal-fired power plants, the largest domestic source of atmospheric mercury emissions in the U.S., are also a major emission source of nitrogen oxides (NOx), sulfur dioxide (S02), and particulate matter (PM). In response to the U.S. Environmental Protection Agency's (EPA's) Clean...

Experimental modeling of NOx and PM generation from combustion of various biodiesel blends for urban transport buses.

DOT National Transportation Integrated Search

2016-08-01

Biodiesel has diverse sources of feedstock and the amount and composition of its emissions vary significantly depending on : combustion conditions. Results of laboratory and field tests reveal that nitrogen oxides (NOx) and particulate matter (PM) : ...

Climate change impacts of US reactive nitrogen.

PubMed

Pinder, Robert W; Davidson, Eric A; Goodale, Christine L; Greaver, Tara L; Herrick, Jeffrey D; Liu, Lingli

2012-05-15

Fossil fuel combustion and fertilizer application in the United States have substantially altered the nitrogen cycle, with serious effects on climate change. The climate effects can be short-lived, by impacting the chemistry of the atmosphere, or long-lived, by altering ecosystem greenhouse gas fluxes. Here we develop a coherent framework for assessing the climate change impacts of US reactive nitrogen emissions, including oxides of nitrogen, ammonia, and nitrous oxide (N(2)O). We use the global temperature potential (GTP), calculated at 20 and 100 y, in units of CO(2) equivalents (CO(2)e), as a common metric. The largest cooling effects are due to combustion sources of oxides of nitrogen altering tropospheric ozone and methane concentrations and enhancing carbon sequestration in forests. The combined cooling effects are estimated at -290 to -510 Tg CO(2)e on a GTP(20) basis. However, these effects are largely short-lived. On a GTP(100) basis, combustion contributes just -16 to -95 Tg CO(2)e. Agriculture contributes to warming on both the 20-y and 100-y timescales, primarily through N(2)O emissions from soils. Under current conditions, these warming and cooling effects partially offset each other. However, recent trends show decreasing emissions from combustion sources. To prevent warming from US reactive nitrogen, reductions in agricultural N(2)O emissions are needed. Substantial progress toward this goal is possible using current technology. Without such actions, even greater CO(2) emission reductions will be required to avoid dangerous climate change.

Climate change impacts of US reactive nitrogen

PubMed Central

Pinder, Robert W.; Davidson, Eric A.; Goodale, Christine L.; Greaver, Tara L.; Herrick, Jeffrey D.; Liu, Lingli

2012-01-01

Fossil fuel combustion and fertilizer application in the United States have substantially altered the nitrogen cycle, with serious effects on climate change. The climate effects can be short-lived, by impacting the chemistry of the atmosphere, or long-lived, by altering ecosystem greenhouse gas fluxes. Here we develop a coherent framework for assessing the climate change impacts of US reactive nitrogen emissions, including oxides of nitrogen, ammonia, and nitrous oxide (N2O). We use the global temperature potential (GTP), calculated at 20 and 100 y, in units of CO2 equivalents (CO2e), as a common metric. The largest cooling effects are due to combustion sources of oxides of nitrogen altering tropospheric ozone and methane concentrations and enhancing carbon sequestration in forests. The combined cooling effects are estimated at −290 to −510 Tg CO2e on a GTP20 basis. However, these effects are largely short-lived. On a GTP100 basis, combustion contributes just −16 to −95 Tg CO2e. Agriculture contributes to warming on both the 20-y and 100-y timescales, primarily through N2O emissions from soils. Under current conditions, these warming and cooling effects partially offset each other. However, recent trends show decreasing emissions from combustion sources. To prevent warming from US reactive nitrogen, reductions in agricultural N2O emissions are needed. Substantial progress toward this goal is possible using current technology. Without such actions, even greater CO2 emission reductions will be required to avoid dangerous climate change. PMID:22547815

40 CFR 98.62 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... electrolysis cells. (b) CO2 emissions from anode consumption during electrolysis in all prebake and Søderberg electrolysis cells. (c) CO2 emissions from on-site anode baking. (d) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, N2O, and CH4 emissions from...

40 CFR 98.62 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... electrolysis cells. (b) CO2 emissions from anode consumption during electrolysis in all prebake and Søderberg electrolysis cells. (c) CO2 emissions from on-site anode baking. (d) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, N2O, and CH4 emissions from...

40 CFR 98.62 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... cells. (b) CO2 emissions from anode consumption during electrolysis in all prebake and Sderberg electrolysis cells. (c) CO2 emissions from on-site anode baking. (d) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, N2O, and CH4 emissions from...

40 CFR 98.62 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... electrolysis cells. (b) CO2 emissions from anode consumption during electrolysis in all prebake and Søderberg electrolysis cells. (c) CO2 emissions from on-site anode baking. (d) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, N2O, and CH4 emissions from...

40 CFR 74.25 - Current promulgated SO2 emissions limit.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Current promulgated SO2 emissions... promulgated SO2 emissions limit. The designated representative shall submit the following data: (a) Current promulgated SO2 emissions limit of the combustion source, expressed in lbs/mmBtu, which shall be the most...

40 CFR 74.24 - Current allowable SO2 emissions rate.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Current allowable SO2 emissions rate... allowable SO2 emissions rate. The designated representative shall submit the following data: (a) Current allowable SO2 emissions rate of the combustion source, expressed in lbs/mmBtu, which shall be the most...

Seasonal changes, identification and source apportionment of PAH in PM1.0

NASA Astrophysics Data System (ADS)

Agudelo-Castañeda, Dayana Milena; Teixeira, Elba Calesso

2014-10-01

The objective of this research was to evaluate the seasonal variation of PAHs in PM1.0, as well as to identify and quantify the contributions of each source profile using the PMF receptor model. PM1.0 samples were collected on PTFE filters from August 2011 to July 2013 in the Metropolitan Area of Porto Alegre, Rio Grande do Sul, Brazil. The samples were extracted using the EPA method TO-13A and 16 Polycyclic Aromatic Hydrocarbons (PAHs) were analyzed using a gaseous chromatograph coupled with a mass spectrometer (GC-MS). Also, the data discussed in this study were analyzed to identify the relations of the PAHs concentrations with NOx, NO, O3 and meteorological parameters (temperature, solar radiation, wind speed, relative humidity). The results showed that in winter, concentrations of total PAHs were significantly higher than in summer, thus showing their seasonal variation. The identification of emission sources by applying diagnostic ratios confirmed that PAHs in the study area originate from mobile sources, especially, from diesel and gasoline emissions. The analysis by PMF receptor model showed the contribution of these two main sources of emissions, too, followed by coal combustion, incomplete combustion/unburned petroleum and wood combustion. The toxic equivalent factors were calculated to characterize the risk of cancer from PAH exposure to PM1.0 samples, and BaP and DahA dominated BaPeq levels.

Light bulb heat exchanger for magnetohydrodynamic generator applications - Preliminary evaluation

NASA Technical Reports Server (NTRS)

Smith, J. M.; Hwang, C. C.; Seikel, G. R.

1974-01-01

The light-bulb heat-exchanger concept is investigated as a possible means of using a combustion heat source to supply energy to an inert gas MHD power generator system. In this concept, combustion gases flow through a central passage which consists of a duct with transparent walls through which heat is transferred by radiation to a radiation receiver which in turn heats the inert gas by convection. The effects of combustion-gas emissivity, transparent-wall-transmissivity, radiation-receiver emissivity, and the use of fins in the inert gas coolant passage are studied. The results indicate that inert gas outlet temperatures of 2500 K are possible for combustion temperatures of 3200 K and that sufficient energy can be transferred from the combustion gas to reduce its temperature to approximately 2000 K. At this temperature more conventional heat exchangers can be used.

Experimental modeling of NOx and PM generation from combustion of various biodiesel blends for urban transport buses : research brief.

DOT National Transportation Integrated Search

2016-08-01

Although it is generally accepted : that biodiesel fuel contributes : to the reduction of pollutants, : biodiesel still needs more study : for better control of combustion emissions and engine performance. Biodiesel has very diverse : sources of feed...

40 CFR 60.1225 - What types of continuous emission monitoring must I perform?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced After August 30... emissions, you must perform four tasks: (a) Install continuous emission monitoring systems for certain...

Emission Measurements of Open Area Combustion Sources with an Unmanned Aerial System

EPA Science Inventory

miniaturized sensor/sampler system (“Kolibri”) on a six-motor, unmanned aerial system (UAS) was used to quantify emissions from open burning of obsolete military propellants. The UAS afforded the ability to sample plume emissions at altitude and from a safe distance ...

SOURCE OF GENOTOXICITY AND CANCER RISK IN AMBIENT AIR

EPA Science Inventory

Products of incomplete combustion are identified as a major source of carcinogenic risk in urban areas, especially those from small non-industrial sources. he major ubiquitous emission i sources outdoors in populated areas are residential home heating and motor vehicles. olycycli...

Mercury emissions from coal combustion in Silesia, analysis using geostatistics

NASA Astrophysics Data System (ADS)

Zasina, Damian; Zawadzki, Jaroslaw

2015-04-01

Data provided by the UNEP's report on mercury [1] shows that solid fuel combustion in significant source of mercury emission to air. Silesia, located in southwestern Poland, is notably affected by mercury emission due to being one of the most industrialized Polish regions: the place of coal mining, production of metals, stone mining, mineral quarrying and chemical industry. Moreover, Silesia is the region with high population density. People are exposed to severe risk of mercury emitted from both: industrial and domestic sources (i.e. small household furnaces). Small sources have significant contribution to total emission of mercury. Official and statistical analysis, including prepared for international purposes [2] did not provide data about spatial distribution of the mercury emitted to air, however number of analysis on Polish public power and energy sector had been prepared so far [3; 4]. The distribution of locations exposed for mercury emission from small domestic sources is interesting matter merging information from various sources: statistical, economical and environmental. This paper presents geostatistical approach to distibution of mercury emission from coal combustion. Analysed data organized in 2 independent levels: individual, bottom-up approach derived from national emission reporting system [5; 6] and top down - regional data calculated basing on official statistics [7]. Analysis, that will be presented, will include comparison of spatial distributions of mercury emission using data derived from sources mentioned above. Investigation will include three voivodeships of Poland: Lower Silesian, Opole (voivodeship) and Silesian using selected geostatistical methodologies including ordinary kriging [8]. References [1] UNEP. Global Mercury Assessment 2013: Sources, Emissions, Releases and Environmental Transport. UNEP Chemicals Branch, Geneva, Switzerland, 2013. [2] NCEM. Poland's Informative Inventory Report 2014. NCEM at the IEP-NRI, 2014. http://www.ceip.at/. [3] Zyśk J., Wyrwa A. and Pluta M. Emissions of mercury from the power sector in Poland. Atmospheric Environment, 45:605-610, 2011. http://dx.doi.org/10.1016/j.atmosenv.2010.10.041/. [4] Głodek A., Pacyna J. Mercury emission from coal-fired power plants in Poland. Atmospheric Environment, 43:5668-5673, 2009. http://dx.doi.org/10.1016/j.atmosenv.2009.07.041. [5] NCEM. National emission database, 2014. NCEM Management at the IEP-NRI. [6] Zasina D. and Zawadzki J. Disaggregation problems using data derived from polish air pollutant emission management system, Systems Supporting Production Engineering. Review of Problems and Solutions, ISBN 978-83-937845-9-2, pp. 128-137, 2014. [7] EUROSTAT. EUROSTAT Energy Database, 2014. [8] Wackernagel H. Basics in Geostatistics 3 Geostatistical Monte-Carlo methods: Conditional simulation, 2013.

Integral emission factors for methane determined using urban flux measurements and local-scale inverse models

NASA Astrophysics Data System (ADS)

Christen, Andreas; Johnson, Mark; Molodovskaya, Marina; Ketler, Rick; Nesic, Zoran; Crawford, Ben; Giometto, Marco; van der Laan, Mike

2013-04-01

The most important long-lived greenhouse gas (LLGHG) emitted during combustion of fuels is carbon dioxide (CO2), however also traces of the LLGHGs methane (CH4) and nitrous oxide (N2O) are released, the quantities of which depend largely on the conditions of the combustion process. Emission factors determine the mass of LLGHGs emitted per energy used (or kilometre driven for cars) and are key inputs for bottom-up emission modelling. Emission factors for CH4 are typically determined in the laboratory or on a test stand for a given combustion system using a small number of samples (vehicles, furnaces), yet associated with larger uncertainties when scaled to entire fleets. We propose an alternative, different approach - Can integrated emission factors be independently determined using direct micrometeorological flux measurements over an urban surface? If so, do emission factors determined from flux measurements (top-down) agree with up-scaled emission factors of relevant combustion systems (heating, vehicles) in the source area of the flux measurement? Direct flux measurements of CH4 were carried out between February and May, 2012 over a relatively densely populated, urban surface in Vancouver, Canada by means of eddy covariance (EC). The EC-system consisted of an ultrasonic anemometer (CSAT-3, Campbell Scientific Inc.) and two open-path infrared gas analyzers (Li7500 and Li7700, Licor Inc.) on a tower at 30m above the surface. The source area of the EC system is characterised by a relative homogeneous morphometry (5.3m average building height), but spatially and temporally varying emission sources, including two major intersecting arterial roads (70.000 cars drive through the 50% source area per day) and seasonal heating in predominantly single-family houses (natural gas). An inverse dispersion model (turbulent source area model), validated against large eddy simulations (LES) of the urban roughness sublayer, allows the determination of the spatial area that contributes to each measurement interval (30 min), which varies with wind direction and stability. A detailed geographic information system of the urban surface combined with traffic counts and building energy models makes it possible to statistically relate fluxes to vehicle density (km driven) and buildings (gas heated volume) - and ultimately quantify the contribution of space heating, transport sector and fugitive emissions to the total emitted CH4 from an urban environment. The measured fluxes of CH4 over the selected urban environment averaged to 22.8 mg CH4 m-2 day-1 during the study period. Compared with the simultaneously measured CO2 emissions, the contribution of CH4, however, accounts for only about 3% of the total LLGHG emissions from this particular urban surface. Traffic contributed 8.8 mg CH4 m-2 day-1, equivalent to 39% of the total CH4 flux. The determined emission factor for the typical fleet composition is 0.062 g CH4 per km driven which is higher than upscaled fleet emission factors (EPA) by a factor of two. This discrepancy can be partially explained through the slower city traffic with frequent idling (traffic congestion), fleet composition and cold starts. Emissions of CH4 by domestic space heating (55% of the total CH4 flux or 12.7 mg CH4 m-2 day-1) are also higher than estimated from upscaled emission factors. There is no evidence of substantial unknown sources such as soil processes, combustion of wood, and leakages from gas distribution pipes (residual: 6% or 1.3 mg CH4 m-2 day-1). The presented study is among the first direct measurements of CH4 emissions over an urban surface and demonstrates that flux measurements of greenhouse gases can be used to determine sources and emission factors in complex urban situations.

40 CFR 62.7860 - Identification of sources-negative declaration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mexico Emissions from Existing Large Municipal Waste Combustion Units § 62.7860 Identification of sources... lands under the jurisdiction of the Albuquerque/Bernalillo county Air Quality Control Board subject to...

40 CFR 62.7860 - Identification of sources-negative declaration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mexico Emissions from Existing Large Municipal Waste Combustion Units § 62.7860 Identification of sources... lands under the jurisdiction of the Albuquerque/Bernalillo county Air Quality Control Board subject to...

Black carbon in the Arctic: the underestimated role of gas flaring and residential combustion emissions

NASA Astrophysics Data System (ADS)

Stohl, A.; Klimont, Z.; Eckhardt, S.; Kupiainen, K.; Shevchenko, V. P.; Kopeikin, V. M.; Novigatsky, A. N.

2013-09-01

Arctic haze is a seasonal phenomenon with high concentrations of accumulation-mode aerosols occurring in the Arctic in winter and early spring. Chemistry transport models and climate chemistry models struggle to reproduce this phenomenon, and this has recently prompted changes in aerosol removal schemes to remedy the modeling problems. In this paper, we show that shortcomings in current emission data sets are at least as important. We perform a 3 yr model simulation of black carbon (BC) with the Lagrangian particle dispersion model FLEXPART. The model is driven with a new emission data set ("ECLIPSE emissions") which includes emissions from gas flaring. While gas flaring is estimated to contribute less than 3% of global BC emissions in this data set, flaring dominates the estimated BC emissions in the Arctic (north of 66° N). Putting these emissions into our model, we find that flaring contributes 42% to the annual mean BC surface concentrations in the Arctic. In March, flaring even accounts for 52% of all Arctic BC near the surface. Most of the flaring BC remains close to the surface in the Arctic, so that the flaring contribution to BC in the middle and upper troposphere is small. Another important factor determining simulated BC concentrations is the seasonal variation of BC emissions from residential combustion (often also called domestic combustion, which is used synonymously in this paper). We have calculated daily residential combustion emissions using the heating degree day (HDD) concept based on ambient air temperature and compare results from model simulations using emissions with daily, monthly and annual time resolution. In January, the Arctic-mean surface concentrations of BC due to residential combustion emissions are 150% higher when using daily emissions than when using annually constant emissions. While there are concentration reductions in summer, they are smaller than the winter increases, leading to a systematic increase of annual mean Arctic BC surface concentrations due to residential combustion by 68% when using daily emissions. A large part (93%) of this systematic increase can be captured also when using monthly emissions; the increase is compensated by a decreased BC burden at lower latitudes. In a comparison with BC measurements at six Arctic stations, we find that using daily-varying residential combustion emissions and introducing gas flaring emissions leads to large improvements of the simulated Arctic BC, both in terms of mean concentration levels and simulated seasonality. Case studies based on BC and carbon monoxide (CO) measurements from the Zeppelin observatory appear to confirm flaring as an important BC source that can produce pollution plumes in the Arctic with a high BC / CO enhancement ratio, as expected for this source type. BC measurements taken during a research ship cruise in the White, Barents and Kara seas north of the region with strong flaring emissions reveal very high concentrations of the order of 200-400 ng m-3. The model underestimates these concentrations substantially, which indicates that the flaring emissions (and probably also other emissions in northern Siberia) are rather under- than overestimated in our emission data set. Our results suggest that it may not be "vertical transport that is too strong or scavenging rates that are too low" and "opposite biases in these processes" in the Arctic and elsewhere in current aerosol models, as suggested in a recent review article (Bond et al., Bounding the role of black carbon in the climate system: a scientific assessment, J. Geophys. Res., 2013), but missing emission sources and lacking time resolution of the emission data that are causing opposite model biases in simulated BC concentrations in the Arctic and in the mid-latitudes.

A balloon system for profiling smoke plumes from forest fires

Treesearch

Paul W. Ryan; Charles D. Tangren; Charles K. McMahon

1979-01-01

This paper is directed to those interested in techniques for measuring emission rates and emission factors for forest fires and other open combustion sources. A source-sampling procedure that involved the use of a vertical array of lightweight, battery-operated instruments suspended from a helium-filled aerodynamic balloon is described. In this procedure, plume...

Carbon isotope-constrained seasonality of carbonaceous aerosol sources from an urban location (Kanpur) in the Indo-Gangetic Plain

NASA Astrophysics Data System (ADS)

Bikkina, Srinivas; Andersson, August; Ram, Kirpa; Sarin, M. M.; Sheesley, Rebecca J.; Kirillova, Elena N.; Rengarajan, R.; Sudheer, A. K.; Gustafsson, Örjan

2017-05-01

The Indo-Gangetic Plain (IGP) in northern India, Pakistan, and Bangladesh is a major source of carbonaceous aerosols in South Asia. However, poorly constrained seasonality of their sources over the IGP leads to large uncertainty in climate and health effects. Here we present a first data set for year-round radiocarbon (Δ14C) and stable carbon (δ13C)-based source apportionment of total carbon (TC) in ambient PM10 (n = 17) collected from an urban site (Kanpur: 26.5°N, 80.3°E) in the IGP during January 2007 to January 2008. The year-round 14C-based fraction biomass (fbio-TC) estimate at Kanpur averages 77 ± 7% and emphasizes an impact of biomass burning emissions (BBEs). The highest fbio-TC (%) is observed in fall season (October-November, 85 ± 6%) followed by winter (December-February, 80 ± 4%) and spring (March-May, 75 ± 8%), while lowest values are found in summer (June-September, 69 ± 2%). Since biomass/coal combustion and vehicular emissions mostly contribute to carbonaceous aerosols over the IGP, we predict δ13CTC (δ13Cpred) over Kanpur using known δ13C source signatures and the measured Δ14C value of each sample. The seasonal variability of δ13Cobs - δ13Cpred versus Δ14CTC together with air mass back trajectories and Moderate Resolution Imaging Spectroradiometer fire count data reveal that carbonaceous aerosols in winter/fall are significantly influenced by atmospheric aging (downwind transport of crop residue burning/wood combustion emissions in the northern IGP), while local sources (wheat residue combustion/vehicular emissions) dominate in spring/summer. Given the large temporal and seasonal variability in sources and emission strength of TC over the IGP, 14C-based constraints are, thus, crucial for reducing their uncertainties in carbonaceous aerosol budgets in climate models.

Research on the Emission Inventory of Major Air Pollutants in 2012 for the Sichuan City Cluster in China

NASA Astrophysics Data System (ADS)

Qian, J.; He, Q.

2014-12-01

This paper developed a high resolution emission inventory of major pollutants in city cluster of Sichuan Basin, one of the most polluted regions in China. The city cluster included five cities, which were Chengdu, Deyang, Mianyang, Meishan and Ziyang. Pollution source census and field measurements were conducted for the major emission sources such as the industry sources, on-road mobile sources, catering sources and the dust sources. The inventory results showed that in the year of 2012, the emission of SO2、NOX、CO、PM10、PM2.5、VOCs and NH3 in the region were 143.5、251.9、1659.9、299.3、163.5、464.1 and 995kt respectively. Chengdu, the provincial capital city, had the largest emission load of every pollutant among the cities. The industry sources, including power plants, fuel combustion facilities and non-combustion processes were the largest emission sources for SO2、NOX and CO, contributing to 84%, 46.5%, 35% of total SO2, NOX and CO emissions. On-road mobile sources accounted for 46.5%, 33%, 16% of the total NOx, CO, PM2.5 emissions and 28% of the anthropogenic VOCs emission. Dust and industry sources contributed to 42% and 23% of the PM10 emission with the dust sources also as the largest source of PM2.5, contributing to 27%. Anthropogenic and biogenic sources took 75% and 25% of the total VOCs emission while 36% of anthropogenic VOCs emission was owing to solvent use. Livestock contributed to 62% of NH3 emissions, followed by nitrogen fertilizer application whose contribution was 23%. Based on the developed emission inventory and local meteorological data, the regional air quality modeling system WRF-CMAQ was applied to simulate the status of PM2.5 pollution in a regional scale. The results showed that high PM2.5 concentration was distributed over the urban area of Chengdu and Deyang. On-road mobile sources and dust sources were two major contributors to the PM2.5 pollution in Chengdu, both had an contribution ratio of 27%. In Deyang, Mianyang, Meishan and Ziyang, industry sources had a relatively high contribution ratio to the PM2.5 pollution, accounting for about 35%, 33%, 38% and 24% respectively.

SO 2 and NO x emissions due to fossil ruel combustion in Saudi Arabia: A preliminary inventory

NASA Astrophysics Data System (ADS)

Ahmed, Azhari Fatahalla Mohamed

Phenomenal economic growth during the last two decades, as a result of oil wealth, has led to a dramatic increase in the demand for fossil fuel in the Kingdom of Saudi Arabia (KSA). In this paper a preliminary inventory for sulfur dioxide (SO 2) and nitrogen oxides (NO x) emitted into the atmosphere as a result of fossil fuel combustion by various economic sectors in KSA in the year 1986 is presented. Emissions are discussed in relation to major source categories (major fuel consuming economic sectors) and on the basis of type of fuel combusted. The data are also geographically disaggregated according to major economic and population centers in KSA in order to show the spatial distribution of emissions. Also, SO 2 and NO x emission trends (1971-1990) were estimated from 1986 data and historical and projected fuel consumption figures.

40 CFR 98.173 - Calculating GHG emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... associated requirements for Tier 4 in subpart C of this part (General Stationary Fuel Combustion Sources). (b..., dry basis (% CO2). Q = Hourly stack gas volumetric flow rate (scfh). %H2O = Hourly moisture percentage... reduction furnace are vented through the same stack as any combustion unit or process equipment that reports...

EXACERBATION OF ATHEROSCLEROSIS FOLLOWING EXPOSURE TO VARIOUS COMBUSTION SOURCE PARTICLES

EPA Science Inventory

Exposure of ApoE knockout (ApoE^-/-) mice to concentrated ambient particles (CAPs) has been shown to increase arterial plaque area and size. CAPs are a complex aerosol mixture consisting of wind-blown dust, emissions from the combustion of fossil fuels, and secondary tr...

ASSESSMENT OF TOXICITY OF OIL COMBUSTION EMISSION EXPOSURE IN NORMAL AND HYPERTENSIVE RATS

EPA Science Inventory

It has been suggested that the increased morbidity and mortality associated with exposure to airborne particulates (PM) is related to materials derived from combustion sources such as gasoline, diesel, oil, wood and coal. In these studies heavy oil # 5 was burned in a residual oi...

40 CFR 98.313 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... You must calculate and report the annual process CO2 emissions for each chloride process line using... subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation... (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the annual...

40 CFR 98.263 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... You must calculate and report the annual process CO2 emissions from each wet-process phosphoric acid... under this subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4... this part (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the...

40 CFR 98.263 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... You must calculate and report the annual process CO2 emissions from each wet-process phosphoric acid... under this subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4... this part (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the...

40 CFR 98.263 - Calculating GHG emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... You must calculate and report the annual process CO2 emissions from each wet-process phosphoric acid... under this subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4... this part (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the...

40 CFR 98.313 - Calculating GHG emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... You must calculate and report the annual process CO2 emissions for each chloride process line using... subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation... (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the annual...

40 CFR 98.263 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... You must calculate and report the annual process CO2 emissions from each wet-process phosphoric acid... under this subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4... this part (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the...

40 CFR 98.313 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... You must calculate and report the annual process CO2 emissions for each chloride process line using... subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation... (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the annual...

40 CFR 98.263 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... You must calculate and report the annual process CO2 emissions from each wet-process phosphoric acid... under this subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4... this part (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the...

40 CFR 98.313 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... You must calculate and report the annual process CO2 emissions for each chloride process line using... subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation... (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the annual...

40 CFR 98.313 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... You must calculate and report the annual process CO2 emissions for each chloride process line using... subpart the process CO2 emissions by operating and maintaining a CEMS according to the Tier 4 Calculation... (General Stationary Fuel Combustion Sources). (b) Calculate and report under this subpart the annual...

VARIABLES AFFECTING EMISSIONS OF PCDDS/FS FROM UNCONTROLLED COMBUSTION OF HOUSEHOLD WASTE IN BARRELS

EPA Science Inventory

The uncontrolled burning of household waste in barrels has recently been implicated as a major source of airborne emissions of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs). Based on the need to generate a more accurate emission factor for burn ba...

Generation and characterization of diesel engine combustion emissions from petroleum diesel and soybean biodiesel fuels and application for inhalation exposure studies

EPA Science Inventory

Biodiesel made from the transesterification of plant- and anmal-derived oils is an important alternative fuel source for diesel engines. Although numerous studies have reported health effects associated with petroleum diesel emissions, information on biodiesel emissions are more ...

Ammonia emissions from non-agricultural sources in the UK

NASA Astrophysics Data System (ADS)

Sutton, M. A.; Dragosits, U.; Tang, Y. S.; Fowler, D.

A detailed literature review has been undertaken of the magnitude of non-agricultural sources of ammonia (NH 3) in the United Kingdom. Key elements of the work included estimation of nitrogen (N) excreted by different sources (birds, animals, babies, human sweat), review of miscellaneous combustion sources, as well as identification of industrial sources and use of NH 3 as a solvent. Overall the total non-agricultural emission of NH 3 from the UK in 1996 is estimated here as 54 (27-106) kt NH 3-N yr -1, although this includes 11 (6-23) kt yr -1 from agriculture related sources (sewage sludge spreading, biomass burning and agro-industry). Compared with previous estimates for 1990, component source magnitudes have changed both because of revised average emissions per source unit (emission factors) and changes in the source activity between 1990 and 1996. Sources with larger average emission factors than before include horses, wild animals and sea bird colonies, industry, sugar beet processing, household products and non-agricultural fertilizer use, with the last three sources being included for the first time. Sources with smaller emission factors than before include: land spreading of sewage sludge, direct human emissions (sweat, breath, smoking, infants), pets (cats and dogs) and fertilizer manufacture. Between 1990 and 1996 source activities increased for sewage spreading (due to reduced dumping at sea) and transport (due to increased use of catalytic converters), but decreased for coal combustion. Combined with the current UK estimates of agricultural NH 3 emissions of 229 kt N yr -1 (1996), total UK NH 3 emissions are estimated at 283 kt N yr -1. Allowing for an import of reduced nitrogen (NH x) of 30 kt N yr -1 and deposition of 230 kt N yr -1, these figures imply an export of 83 kt NH 3-N yr -1. Although export is larger than previously estimated, due to the larger contribution of non-agricultural NH 3 emissions, it is still insufficient to balance the UK budget, for which around 150 kt NH 3-N are estimated to be exported. The shortfall in the budget is, nevertheless, well within the range of uncertainty of the total emissions.

Carbon flow analysis and Carbon emission reduction of FCC in Chinese oil refineries

NASA Astrophysics Data System (ADS)

Jia, Fengrui; Wei, Na; Ma, Danzhu; Liu, Guangxin; Wu, Ming; Yue, Qiang

2017-08-01

The major problem of the energy production in oil refineries is the high emission of CO2 in China. The fluid catalytic cracking unit (FCC) is the key source of carbon emission in the oil refineries. According to the statistical data, the carbon emission of FCC unit accounts for more than 31% for the typical oil refineries. The carbon flow of FCC in the typical Chinese oil refineries were evaluated and analysed, which aimed at the solution of CO2 emission reduction. The method of substances flow analysis (SFA) and the mathematical programming were used to evaluate the carbon metabolism and optimize the carbon emission. The results indicated that the combustion emission of the reaction-regeneration subsystem (RRS) was the major source of FCC. The quantity of CO2 emission of RSS was more than 90%. The combustion efficiency and the amount of residual oil affected the carbon emission of RRS most according to the optimized analysis of carbon emission reduction. Moreover, the fractionation subsystem (TFS) had the highest environmental efficiency and the absorption-stabilization subsystem (ASS) had the highest resource efficiency (approximately to 1) of carbon.

Improvement of a Global High-Resolution Ammonia Emission Inventory for Combustion and Industrial Sources with New Data from the Residential and Transportation Sectors.

PubMed

Meng, Wenjun; Zhong, Qirui; Yun, Xiao; Zhu, Xi; Huang, Tianbo; Shen, Huizhong; Chen, Yilin; Chen, Han; Zhou, Feng; Liu, Junfeng; Wang, Xinming; Zeng, Eddy Y; Tao, Shu

2017-03-07

There is increasing evidence indicating the critical role of ammonia (NH 3 ) in the formation of secondary aerosols. Therefore, high quality NH 3 emission inventory is important for modeling particulate matter in the atmosphere. Unfortunately, without directly measured emission factors (EFs) in developing countries, using data from developed countries could result in an underestimation of these emissions. A series of newly reported EFs for China provide an opportunity to update the NH 3 emission inventory. In addition, a recently released fuel consumption data product has allowed for a multisource, high-resolution inventory to be assembled. In this study, an improved global NH 3 emission inventory for combustion and industrial sources with high sectorial (70 sources), spatial (0.1° × 0.1°), and temporal (monthly) resolutions was compiled for the years 1960 to 2013. The estimated emissions from transportation (1.59 Tg) sectors in 2010 was 2.2 times higher than those of previous reports. The spatial variation of the emissions was associated with population, gross domestic production, and temperature. Unlike other major air pollutants, NH 3 emissions continue to increase, even in developed countries, which is likely caused by an increased use of biomass fuel in the residential sector. The emissions density of NH 3 in urban areas is an order of magnitude higher than in rural areas.

Estimation of mercury emission from different sources to atmosphere in Chongqing, China.

PubMed

Wang, Dingyong; He, Lei; Wei, Shiqiang; Feng, Xinbin

2006-08-01

This investigation presents a first assessment of the contribution to the regional mercury budget from anthropogenic and natural sources in Chongqing, an important industrial region in southwest China. The emissions of mercury to atmosphere from anthropogenic sources in the region were estimated through indirect approaches, i.e. using commonly acceptable emission factors method, which based on annual process throughputs or consumption for these sources. The natural mercury emissions were estimated from selected natural sources by the dynamic flux chamber technique. The results indicated that the anthropogenic mercury emissions totaled approximately 8.85 tons (t), more than 50% of this total originated in coal combustion and 23.7% of this total emission in the industrial process (include cement production, metal smelting and chemical industry). The natural emissions represented approximately 17% of total emissions (1.78 t yr(-1)). The total mercury emission to atmosphere in Chongqing in 2001 was 10.63 t.

40 CFR Table 6 to Subpart Eeee of... - Initial Compliance With Emission Limits

Code of Federal Regulations, 2010 CFR

2010-07-01

... approval, TOC) emissions by at least 95 weight-percent, or as an option for nonflare combustion devices to an exhaust concentration of ≤20 ppmv Total organic HAP (or, upon approval, TOC) emissions, based on..., or new affected source Reduce total organic HAP (or, upon approval, TOC) emissions from the loading...

40 CFR 74.24 - Current allowable SO2 emissions rate.

Code of Federal Regulations, 2011 CFR

2011-07-01

... allowable SO2 emissions rate of the combustion source, expressed in lbs/mmBtu, which shall be the most... application. If the allowable SO2 emissions rate is not expressed in lbs/mmBtu, the allowable emissions rate shall be converted to lbs/mmBtu by multiplying the allowable rate by the appropriate factor as specified...

Study on key technologies of optimization of big data for thermal power plant performance

NASA Astrophysics Data System (ADS)

Mao, Mingyang; Xiao, Hong

2018-06-01

Thermal power generation accounts for 70% of China's power generation, the pollutants accounted for 40% of the same kind of emissions, thermal power efficiency optimization needs to monitor and understand the whole process of coal combustion and pollutant migration, power system performance data show explosive growth trend, The purpose is to study the integration of numerical simulation of big data technology, the development of thermal power plant efficiency data optimization platform and nitrogen oxide emission reduction system for the thermal power plant to improve efficiency, energy saving and emission reduction to provide reliable technical support. The method is big data technology represented by "multi-source heterogeneous data integration", "large data distributed storage" and "high-performance real-time and off-line computing", can greatly enhance the energy consumption capacity of thermal power plants and the level of intelligent decision-making, and then use the data mining algorithm to establish the boiler combustion mathematical model, mining power plant boiler efficiency data, combined with numerical simulation technology to find the boiler combustion and pollutant generation rules and combustion parameters of boiler combustion and pollutant generation Influence. The result is to optimize the boiler combustion parameters, which can achieve energy saving.

Radiocarbon determination of fossil and contemporary carbon contribution to aerosol in the Pacific Islands.

PubMed

Isley, C F; Nelson, P F; Taylor, M P; Williams, A A; Jacobsen, G E

2018-06-21

Combustion emissions are of growing concern across all Pacific Island Countries, which account for >10,000 km 2 of the earth's surface area; as for many other small island states globally. Apportioning emissions inputs for Suva, the largest Pacific Island city, will aid in development of emission reduction strategies. Total suspended particulate (TSP) and fine particulate (PM 2.5 ) samples were collected for Suva City, a residential area (Kinoya, TSP) and a mainly ocean-influenced site (Suva Point, TSP) from 2014 to 2015. Percentages of contemporary and fossil carbon were determined by radiocarbon analysis (accelerator mass spectrometry); for non‑carbonate carbon (NCC), elemental carbon (EC) and organic carbon (OC). Source contributions to particulate matter were identified and the accuracy of previous emissions inventory and source apportionment studies was evaluated. Suva Point NCC concentrations (2.7 ± 0.4 μg/m 3 ) were four times lower than for City (13 ± 2 μg/m 3 in TSP) and Kinoya (13 ± 1 μg/m 3 in TSP); demonstrating the contribution of land-based emissions activities in city and residential areas. In Suva City, total NCC in air was 81% (79%-83%) fossil carbon, from vehicles, shipping, power generation and industry; whilst in the residential area, 48% (46%-50%) of total NCC was contemporary carbon; reflecting the higher incidence of biomass and waste burning and of cooking activities. Secondary organic fossil carbon sources contributed >36% of NCC mass at the city and >29% at Kinoya; with biogenic carbon being Kinoya's most significant source (approx. 30% of NCC mass). These results support the previous source apportionment studies for the city area; yet show that, in line with emissions inventory studies, biomass combustion contributes more PM 2.5 mass in residential areas. Hence air quality management strategies need to target open burning activities as well as fossil fuel combustion. Copyright © 2018 Elsevier B.V. All rights reserved.

Directions for combustion engine aerosol measurement in the 21st century.

PubMed

Maricq, M Matti; Maldonado, Hector

2010-10-01

The Coordinating Research Council convened two Real-Time PM Measurement Workshops in December 2008 and March 2009 to take an intensive look at the current status and future directions of combustion aerosol measurement. The purpose was to examine the implications of parallel rapid developments over the past decade in ambient aerosol science, engine aftertreatment technology, and aerosol measurement methodology, which provide benefits and challenges to the stakeholders in air quality management. The workshops were organized into sessions targeting key issues in ambient and source combustion particulate matter (PM). These include (1) metrics to characterize and quantify PM, (2) the need to reconcile ambient and source measurements, (3) the role of atmospheric transformations on modeling emissions and exposures, (4) the impact of sampling conditions on PM measurement, and (5) the potential benefits of novel PM instrumentation. This paper distills the material presented by subject experts and the insights derived from the in-depth discussions that formed the core of each session. The paper's objectives are to identify areas of consensus that allow wider practical application of the past decade's advances in combustion aerosol measurement to improve emissions and air quality modeling, develop emissions reduction strategies, and to recommend directions for progress on issues in which uncertainties remain.

Comparative Chemistry and Toxicity of Diesel and Biomass Combustion Emissions

EPA Science Inventory

Air pollution includes a complex mixture of carbonaceous gases and particles emitted from multiple anthropogenic, biogenic, and biomass burning sources, and also includes secondary organic components that form during atmospheric aging of these emissions. Exposure to these mixture...

SUMMARY REPORT CONTROL OF NOX EMISSIONS BY REBURNING

EPA Science Inventory

This report covers NO_x control employing reburning technology: A new, effective method of controlling NO_x emissions from a wide range of stationary combustion sources including large, coal-fired, utility boilers. Although reburning potentially is applicable ...

40 CFR 63.6145 - What notifications must I submit and when?

Code of Federal Regulations, 2011 CFR

2011-07-01

... when? 63.6145 Section 63.6145 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines Notifications...

Mutagenicity and Pollutant Emission Factors of Solid-Fuel Cookstoves: Comparison with Other Combustion Sources

PubMed Central

Mutlu, Esra; Warren, Sarah H.; Ebersviller, Seth M.; Kooter, Ingeborg M.; Schmid, Judith E.; Dye, Janice A.; Linak, William P.; Gilmour, M. Ian; Jetter, James J.; Higuchi, Mark; DeMarini, David M.

2016-01-01

Background: Emissions from solid fuels used for cooking cause ~4 million premature deaths per year. Advanced solid-fuel cookstoves are a potential solution, but they should be assessed by appropriate performance indicators, including biological effects. Objective: We evaluated two categories of solid-fuel cookstoves for eight pollutant and four mutagenicity emission factors, correlated the mutagenicity emission factors, and compared them to those of other combustion emissions. Methods: We burned red oak in a 3-stone fire (TSF), a natural-draft stove (NDS), and a forced-draft stove (FDS), and we combusted propane as a liquified petroleum gas control fuel. We determined emission factors based on useful energy (megajoules delivered, MJd) for carbon monoxide, nitrogen oxides (NOx), black carbon, methane, total hydrocarbons, 32 polycyclic aromatic hydrocarbons, PM2.5, levoglucosan (a wood-smoke marker), and mutagenicity in Salmonella. Results: With the exception of NOx, the emission factors per MJd were highly correlated (r ≥ 0.97); the correlation for NOx with the other emission factors was 0.58–0.76. Excluding NOx, the NDS and FDS reduced the emission factors an average of 68 and 92%, respectively, relative to the TSF. Nevertheless, the mutagenicity emission factor based on fuel energy used (MJthermal) for the most efficient stove (FDS) was between those of a large diesel bus engine and a small diesel generator. Conclusions: Both mutagenicity and pollutant emission factors may be informative for characterizing cookstove performance. However, mutagenicity emission factors may be especially useful for characterizing potential health effects and should be evaluated in relation to health outcomes in future research. An FDS operated as intended by the manufacturer is safer than a TSF, but without adequate ventilation, it will still result in poor indoor air quality. Citation: Mutlu E, Warren SH, Ebersviller SM, Kooter IM, Schmid JE, Dye JA, Linak WP, Gilmour MI, Jetter JJ, Higuchi M, DeMarini DM. 2016. Mutagenicity and pollutant emission factors of solid-fuel cookstoves: comparison with other combustion sources. Environ Health Perspect 124:974–982; http://dx.doi.org/10.1289/ehp.1509852 PMID:26895221

Chemical characteristic and toxicity assessment of particle associated PAHs for the short-term anthropogenic activity event: During the Chinese New Year's Festival in 2013.

PubMed

Shi, Guo-Liang; Liu, Gui-Rong; Tian, Ying-Ze; Zhou, Xiao-Yu; Peng, Xing; Feng, Yin-Chang

2014-06-01

PM10 and PM2.5 samples were simultaneously collected during a period which covered the Chinese New Year's (CNY) Festival. The concentrations of particulate matter (PM) and 16 polycyclic aromatic hydrocarbons (PAHs) were measured. The possible source contributions and toxicity risks were estimated for Festival and non-Festival periods. According to the diagnostic ratios and Multilinear Engine 2 (ME2), three sources were identified and their contributions were calculated: vehicle emission (48.97% for PM10, 53.56% for PM2.5), biomass & coal combustion (36.83% for PM10, 28.76% for PM2.5), and cook emission (22.29% for PM10, 27.23% for PM2.5). An interesting result was found: although the PAHs are not directly from the fireworks display, they were still indirectly influenced by biomass combustion which is affiliated with the fireworks display. Additionally, toxicity risks of different sources were estimated by Multilinear Engine 2-BaP equivalent (ME2-BaPE): vehicle emission (54.01% for PM10, 55.42% for PM2.5), cook emission (25.59% for PM10, 29.05% for PM2.5), and biomass & coal combustion source (20.90% for PM10, 14.28% for PM2.5). It is worth to be noticed that the toxicity contribution of cook emission was considerable in Festival period. The findings can provide useful information to protect the urban human health, as well as develop the effective air control strategies in special short-term anthropogenic activity event. Copyright © 2014 Elsevier B.V. All rights reserved.

Distribution and Source Apportionment of Polycyclic Aromatic Hydrocarbons (PAHs) in Forest Soils from Urban to Rural Areas in the Pearl River Delta of Southern China

PubMed Central

Xiao, Yihua; Tong, Fuchun; Kuang, Yuanwen; Chen, Bufeng

2014-01-01

The upper layer of forest soils (0–20 cm depth) were collected from urban, suburban, and rural areas in the Pearl River Delta of Southern China to estimate the distribution and the possible sources of polycyclic aromatic hydrocarbons (PAHs). Total concentrations of PAHs in the forest soils decreased significantly along the urban–suburban–rural gradient, indicating the influence of anthropogenic emissions on the PAH distribution in forest soils. High and low molecular weight PAHs dominated in the urban and rural forest soils, respectively, implying the difference in emission sources between the areas. The values of PAH isomeric diagnostic ratios indicated that forest soil PAHs were mainly originated from traffic emissions, mixed sources and coal/wood combustion in the urban, suburban and rural areas, respectively. Principal component analysis revealed that traffic emissions, coal burning and residential biomass combustion were the three primary contributors to forest soil PAHs in the Pearl River Delta. Long range transportation of PAHs via atmosphere from urban area might also impact the PAHs distribution in the forest soils of rural area. PMID:24599040

Vapor hydrogen and oxygen isotopes reflect water of combustion in the urban atmosphere.

PubMed

Gorski, Galen; Strong, Courtenay; Good, Stephen P; Bares, Ryan; Ehleringer, James R; Bowen, Gabriel J

2015-03-17

Anthropogenic modification of the water cycle involves a diversity of processes, many of which have been studied intensively using models and observations. Effective tools for measuring the contribution and fate of combustion-derived water vapor in the atmosphere are lacking, however, and this flux has received relatively little attention. We provide theoretical estimates and a first set of measurements demonstrating that water of combustion is characterized by a distinctive combination of H and O isotope ratios. We show that during periods of relatively low humidity and/or atmospheric stagnation, this isotopic signature can be used to quantify the concentration of water of combustion in the atmospheric boundary layer over Salt Lake City. Combustion-derived vapor concentrations vary between periods of atmospheric stratification and mixing, both on multiday and diurnal timescales, and respond over periods of hours to variations in surface emissions. Our estimates suggest that up to 13% of the boundary layer vapor during the period of study was derived from combustion sources, and both the temporal pattern and magnitude of this contribution were closely reproduced by an independent atmospheric model forced with a fossil fuel emissions data product. Our findings suggest potential for water vapor isotope ratio measurements to be used in conjunction with other tracers to refine the apportionment of urban emissions, and imply that water vapor emissions associated with combustion may be a significant component of the water budget of the urban boundary layer, with potential implications for urban climate, ecohydrology, and photochemistry.

Vapor hydrogen and oxygen isotopes reflect water of combustion in the urban atmosphere

PubMed Central

Gorski, Galen; Strong, Courtenay; Good, Stephen P.; Bares, Ryan; Ehleringer, James R.; Bowen, Gabriel J.

2015-01-01

Anthropogenic modification of the water cycle involves a diversity of processes, many of which have been studied intensively using models and observations. Effective tools for measuring the contribution and fate of combustion-derived water vapor in the atmosphere are lacking, however, and this flux has received relatively little attention. We provide theoretical estimates and a first set of measurements demonstrating that water of combustion is characterized by a distinctive combination of H and O isotope ratios. We show that during periods of relatively low humidity and/or atmospheric stagnation, this isotopic signature can be used to quantify the concentration of water of combustion in the atmospheric boundary layer over Salt Lake City. Combustion-derived vapor concentrations vary between periods of atmospheric stratification and mixing, both on multiday and diurnal timescales, and respond over periods of hours to variations in surface emissions. Our estimates suggest that up to 13% of the boundary layer vapor during the period of study was derived from combustion sources, and both the temporal pattern and magnitude of this contribution were closely reproduced by an independent atmospheric model forced with a fossil fuel emissions data product. Our findings suggest potential for water vapor isotope ratio measurements to be used in conjunction with other tracers to refine the apportionment of urban emissions, and imply that water vapor emissions associated with combustion may be a significant component of the water budget of the urban boundary layer, with potential implications for urban climate, ecohydrology, and photochemistry. PMID:25733906

METHANE EMISSIONS FROM THE NATURAL GAS INDUSTRY VOLUME 6: VENTED & COMBUSTION SOURCE SUMMARY

EPA Science Inventory

The 15-volume report summarizes the results of a comprehensive program to quantify methane (CH4) emissions from the U.S. natural gas industry for the base year. The objective was to determine CH4 emissions from the wellhead and ending downstream at the customer's meter. The accur...

Comparative dose-response assessment of various combustion source particles to indcue acute lung-injury and exacerbate atherosclerosis in ApoE-Mice

EPA Science Inventory

Exposure to concentrated ambient particles (CAPs) has been shown to increase arterial plaque area and size in atherosclerosis susceptible mice. CAPs are a complex aerosol mixture consisting of wind-blown dust. emissions from the combustion of fossil fuels, and secondary transform...

40 CFR 98.173 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... associated requirements for Tier 4 in subpart C of this part (General Stationary Fuel Combustion Sources). (b... stack gas volumetric flow rate (scfh). %H2O = Hourly moisture percentage in the stack gas. (iii) You... Tier 4 methodology in subpart C of this part, or through the same stack as any combustion unit or...

40 CFR 98.173 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... associated requirements for Tier 4 in subpart C of this part (General Stationary Fuel Combustion Sources). (b... basis (% CO2). Q = Hourly stack gas volumetric flow rate (scfh). %H2O = Hourly moisture percentage in... furnace are vented through the same stack as any combustion unit or process equipment that reports CO2...

COMPARATIVE POTENCY METHOD FOR CANCER RISK ASSESSMENT: APPLICATION TO THE QUANTITATIVE ASSESSMENT OF THE CONTRIBUTION OF COMBUSTION EMISSIONS TO LUNG CANCER RISK

EPA Science Inventory

Combustion sources emit soot particles containing carcinogenic polycyclic organic compounds which are mutagenic in short-term genetic bioassays in microbial and mammalian cells and are tumorigenic in animals. Although soot is considered to be a human carcinogen, soots from differ...

COMBUSTION MODIFICATION CONTROL OF NITROGEN OXIDES (EPA/600/F-95/012)

EPA Science Inventory

EPA's efforts in research and development of nitrogen oxide (NOx) control technologies by
means of modifying the combustion process have played a major role in reducing stationary
source NOx emissions by over 3 million tons (2.73 x 10^6 tonnes) annually, and have led to at<...

Particulate matter emissions from combustion of wood in district heating applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghafghazi, S.; Sowlati, T.; Sokhansanj, Shahabaddine

2011-01-01

The utilization of wood biomass to generate district heat and power in communities that have access to this energy source is increasing. In this paper the effect of wood fuel properties, combustion condition, and flue gas cleaning system on variation in the amount and formation of particles in the flue gas of typical district heating wood boilers are discussed based on the literature survey. Direct measurements of particulate matter (PM) emissions from wood boilers with district heating applications are reviewed and presented. Finally, recommendations are given regarding the selection of wood fuel, combustion system condition, and flue gas cleaning systemmore » in district heating systems in order to meet stringent air quality standards. It is concluded that utilization of high quality wood fuel, such as wood pellets produced from natural, uncontaminated stem wood, would generate the least PM emissions compared to other wood fuel types. Particulate matter emissions from grate burners equipped with electrostatic precipitators when using wood pellets can be well below stringent regulatory emission limit such as particulate emission limit of Metro Vancouver, Canada.« less

AIR POLLUTION CONTROL TECHNOLOGIES (CHAPTER 65)

EPA Science Inventory

The chapter discusses the use of technologies for reducing air pollution emissions from stationary sources, with emphasis on the control of combustion gen-erated air pollution. Major stationary sources include utility power boilers, industrial boilers and heaters, metal smelting ...

A practical approach to estimate emission rates of indoor air pollutants due to the use of personal combustible products based on small-chamber studies.

PubMed

Szulejko, Jan E; Kim, Ki-Hyun

2016-02-01

As emission rates of airborne pollutants are commonly measured from combusting substances placed inside small chambers, those values need to be re-evaluated for the possible significance under practical conditions. Here, a simple numerical procedure is investigated to extrapolate the chamber-based emission rates of formaldehyde that can be released from various combustible sources including e-cigarettes, conventional cigarettes, or scented candles to their concentration levels in a small room with relatively poor ventilation. This simple procedure relies on a mass balance approach by considering the masses of pollutants emitted from source and lost through ventilation under the assumption that mixing occurs instantaneously in the room without chemical reactions or surface sorption. The results of our study provide valuable insights into re-evaluation procedure of chamber data to allow comparison between extrapolated and recommended values to judge the safe use of various combustible products in confined spaces. If two scented candles with a formaldehyde emission rate of 310 µg h(-1) each were lit for 4 h in a small 20 m(3) room with an air change rate of 0.5 h(-1), then the 4-h (candle lit) and 8-h (up to 8 h after candle lighting) TWA [FA] were determined to be 28.5 and 23.5 ppb, respectively. This is clearly above the 8-h NIOSH recommended exposure limit (REL) time weighted average of 16 ppb. Copyright © 2015 Elsevier Ltd. All rights reserved.

Speciated non-methane organic compounds emissions from food cooking in Mexico

NASA Astrophysics Data System (ADS)

Mugica, V.; Vega, E.; Chow, J.; Reyes, E.; Sánchez, G.; Arriaga, J.; Egami, R.; Watson, J.

Non-methane organic compound (NMOC) emissions from different sorts of food preparation sites, were quantified for the first time in Mexico, in order to develop emission profiles for further application in the chemical mass balance receptor model (CMB). Restaurants using charcoal grills and LP gas stoves, "tortillerías", food frying places and rotisseries were sampled using SUMMA ® stainless-steel canisters to analyse NMOC by high-resolution gas chromatography. The results obtained show that profiles determined from food cooking processes have similarities to those found in LP gas combustion, which is the most common fuel in Mexico used for this purpose, although there were differences in the relative composition of propane and butane in both cases. This suggests that, the rates of combustion of propane and butane are different. It has also been detected that propene, a reactive olefin is produced during the combustion process. The obtained profiles of restaurants, rotisseries and fried food show an important contribution of two carbon compounds (ethane, ethylene and acetylene) that can be attributed to the complex process of grease and meat cooking. The presence of these compounds cannot be attributed to vehicular sources since the concentrations are higher than in ambient air. These were also determined from aromatic compounds such as benzene, toluene and xylene in the combustion of vegetal charcoal. The measured concentrations indicate that NMOC emissions from cooking may become an important indoor source of NMOC under crowded conditions in closed places.

Characteristics of NOx emission from Chinese coal-fired power plants equipped with new technologies

NASA Astrophysics Data System (ADS)

Ma, Zizhen; Deng, Jianguo; Li, Zhen; Li, Qing; Zhao, Ping; Wang, Liguo; Sun, Yezhu; Zheng, Hongxian; Pan, Li; Zhao, Shun; Jiang, Jingkun; Wang, Shuxiao; Duan, Lei

2016-04-01

Coal combustion in coal-fired power plants is one of the important anthropogenic NOx sources, especially in China. Many policies and methods aiming at reducing pollutants, such as increasing installed capacity and installing air pollution control devices (APCDs), especially selective catalytic reduction (SCR) units, could alter NOx emission characteristics (NOx concentration, NO2/NOx ratio, and NOx emission factor). This study reported the NOx characteristics of eight new coal-fired power-generating units with different boiler patterns, installed capacities, operating loads, and coal types. The results showed that larger units produced less NOx, and anthracite combustion generated more NOx than bitumite and lignite combustion. During formation, the NOx emission factors varied from 1.81 to 6.14 g/kg, much lower than those of older units at similar scales. This implies that NOx emissions of current and future units could be overestimated if they are based on outdated emission factors. In addition, APCDs, especially SCR, greatly decreased NOx emissions, but increased NO2/NOx ratios. Regardless, the NO2/NOx ratios were lower than 5%, in accordance with the guidelines and supporting the current method for calculating NOx emissions from coal-fired power plants that ignore NO2.

Magnetic characteristics of industrial dust from different sources of emission: A case study of Poland

NASA Astrophysics Data System (ADS)

Szuszkiewicz, Marcin; Magiera, Tadeusz; Kapička, Aleš; Petrovský, Eduard; Grison, Hanna; Gołuchowska, Beata

2015-05-01

Dust emission and deposition in topsoil have negative effect on individual components of the ecosystem. In addition to routine geochemical analyses, magnetic measurements may provide useful complementary information related to the type, concentration and grain-size distribution of the technogenic magnetic particles (TMPs) and thus the degree of contamination of the environment. The aim of this contribution is to use magnetic parameters in distinguishing dust from a wide range of sources of air pollution (power industry, cement, coke, ceramic industries and biomass combustion). We measured magnetic susceptibility, hysteresis parameters and thermomagnetic curves. Our results suggest that predominant component in tested samples is magnetite, only dust from coking plant and the combustion of lignite contained also maghemite and/or hematite. Mixture of sizes, ranging from fine single-domain to coarse multi-domain grains, was detected. Our results indicate that industrial dusts from various sources of emissions have different specific magnetic properties and magnetic measurements may provide very helpful information.

Large contribution of fossil fuel derived secondary organic carbon to water soluble organic aerosols in winter haze in China

NASA Astrophysics Data System (ADS)

Zhang, Yan-Lin; El-Haddad, Imad; Huang, Ru-Jin; Ho, Kin-Fai; Cao, Jun-Ji; Han, Yongming; Zotter, Peter; Bozzetti, Carlo; Daellenbach, Kaspar R.; Slowik, Jay G.; Salazar, Gary; Prévôt, André S. H.; Szidat, Sönke

2018-03-01

Water-soluble organic carbon (WSOC) is a large fraction of organic aerosols (OA) globally and has significant impacts on climate and human health. The sources of WSOC remain very uncertain in polluted regions. Here we present a quantitative source apportionment of WSOC, isolated from aerosols in China using radiocarbon (14C) and offline high-resolution time-of-flight aerosol mass spectrometer measurements. Fossil emissions on average accounted for 32-47 % of WSOC. Secondary organic carbon (SOC) dominated both the non-fossil and fossil derived WSOC, highlighting the importance of secondary formation to WSOC in severe winter haze episodes. Contributions from fossil emissions to SOC were 61 ± 4 and 50 ± 9 % in Shanghai and Beijing, respectively, significantly larger than those in Guangzhou (36 ± 9 %) and Xi'an (26 ± 9 %). The most important primary sources were biomass burning emissions, contributing 17-26 % of WSOC. The remaining primary sources such as coal combustion, cooking and traffic were generally very small but not negligible contributors, as coal combustion contribution could exceed 10 %. Taken together with earlier 14C source apportionment studies in urban, rural, semi-urban and background regions in Asia, Europe and the USA, we demonstrated a dominant contribution of non-fossil emissions (i.e., 75 ± 11 %) to WSOC aerosols in the Northern Hemisphere; however, the fossil fraction is substantially larger in aerosols from East Asia and the eastern Asian pollution outflow, especially during winter, due to increasing coal combustion. Inclusion of our findings can improve a modelling of effects of WSOC aerosols on climate, atmospheric chemistry and public health.

THE ONTARIO HYDRO METHOD FOR SPECIATED MERCURY MEASUREMENTS: ISSUES AND CONSIDERATIONS

EPA Science Inventory

The Ontario Hydro (OH) method has been developed for the measurement of total and speciated mercury emissions from coal-fired combustion sources. The OH method was initially developed to support EPA's information collection request to characterize and inventory mercury emissions ...

40 CFR 63.6150 - What reports must I submit and when?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines... this section, unless the Administrator has approved a different schedule. (1) Company name and address...

40 CFR 63.6150 - What reports must I submit and when?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines Notifications... section, unless the Administrator has approved a different schedule. (1) Company name and address. (2...

40 CFR 63.6150 - What reports must I submit and when?

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines... this section, unless the Administrator has approved a different schedule. (1) Company name and address...

40 CFR 63.9600 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... correspond to your standard operating procedures for maintaining the proper and efficient combustion within... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing Operation...

40 CFR 63.9600 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... correspond to your standard operating procedures for maintaining the proper and efficient combustion within... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing Operation...

40 CFR 63.9600 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... correspond to your standard operating procedures for maintaining the proper and efficient combustion within... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Taconite Iron Ore Processing Operation...

Highly-controlled, reproducible measurements of aerosol emissions from African biomass combustion

NASA Astrophysics Data System (ADS)

Haslett, Sophie; Thomas, J. Chris; Morgan, William; Hadden, Rory; Liu, Dantong; Allan, James; Williams, Paul; Sekou, Keïta; Liousse, Catherine; Coe, Hugh

2017-04-01

Particulate emissions from biomass burning can alter the atmosphere's radiative balance and cause significant harm to human health. However, the relationship between these emissions and fundamental combustion processes is, to date, poorly characterised. In atmospheric models, aerosol emissions are represented by emission factors based on mass loss, which are averaged over an entire combustion event for each particulate species. This approach, however, masks huge variability in emissions during different phases of the combustion period. Laboratory tests have shown that even small changes to the burning environment can lead to huge variation in observed aerosol emission factors (Akagi et al., 2011). In order to address this gap in understanding, in this study, small wood samples sourced from Côte D'Ivoire were burned in a highly-controlled laboratory environment. The shape and mass of samples, available airflow and surrounding heat were carefully regulated. Organic aerosol and refractory black carbon emissions were measured in real-time using an Aerosol Mass Spectrometer and a Single Particle Soot Photometer, respectively. Both of these instruments are used regularly to measure aerosol concentrations in the field. This methodology produced remarkably repeatable results, allowing three different phases of combustion to be identified by their emissions. Black carbon was emitted predominantly during flaming combustion; organic aerosols were emitted during pyrolysis before ignition and from smouldering-dominated behaviour near the end of combustion. During the flaming period, there was a strong correlation between the emission of black carbon and the rate of mass loss, which suggests there is value in employing a mass-based emission factor for this species. However, very little correlation was seen between organic aerosol and mass loss throughout the tests. As such, results here suggest that emission factors averaged over an entire combustion event are unlikely to be useful for organic aerosol emissions. The two different phases producing organic aerosol, pyrolysis and smouldering, were observed to have different mass spectra. In previous ambient experiments, two organic factors with very comparable signatures to these have been identified using positive matrix factorisation (Young et al., 2015). As such, it is postulated that these ambient organic factors are likely associated with the two combustion phases identified here. References: Akagi, S. K., Yokelson, R. J., Wiedinmyer, C., Alvarado, M. J., Reid, J. S., Karl, T., Crounse, J. D. and Wennberg, P. O., Emission factors for open and domestic biomass burning for use in atmospheric models. Atmos. Chem. Phys., 11, 4039-4072 (2011) Young, D. E., Allan, J. D., Williams, P. I., Green, D. C., Harrison, R. M., Yin, J., Flynn, M. J., Gallagher, M. W., Coe, H., Investigating a two-component model of solid fuel organic aerosol in London: processes, PM1 contribution, and seasonality. Atmos. Chem. Phys, 15, 2429-2443 (2015)

Emissions from the combustion of eucalypt and pine chips in a fluidized bed reactor.

PubMed

Vicente, E D; Tarelho, L A C; Teixeira, E R; Duarte, M; Nunes, T; Colombi, C; Gianelle, V; da Rocha, G O; Sanchez de la Campa, A; Alves, C A

2016-04-01

Interest in renewable energy sources has increased in recent years due to environmental concerns about global warming and air pollution, reduced costs and improved efficiency of technologies. Under the European Union (EU) energy directive, biomass is a suitable renewable source. The aim of this study was to experimentally quantify and characterize the emission of particulate matter (PM2.5) resulting from the combustion of two biomass fuels (chipped residual biomass from pine and eucalypt), in a pilot-scale bubbling fluidized bed (BFB) combustor under distinct operating conditions. The variables evaluated were the stoichiometry and, in the case of eucalypt, the leaching of the fuel. The CO and PM2.5 emission factors were lower when the stoichiometry used in the experiments was higher (0.33±0.1 g CO/kg and 16.8±1.0 mg PM2.5/kg, dry gases). The treatment of the fuel by leaching before its combustion has shown to promote higher PM2.5 emissions (55.2±2.5 mg/kg, as burned). Organic and elemental carbon represented 3.1 to 30 wt.% of the particle mass, while carbonate (CO3(2-)) accounted for between 2.3 and 8.5 wt.%. The particulate mass was mainly composed of inorganic matter (71% to 86% of the PM2.5 mass). Compared to residential stoves, BFB combustion generated very high mass fractions of inorganic elements. Chloride was the water soluble ion in higher concentration in the PM2.5 emitted by the combustion of eucalypt, while calcium was the dominant water soluble ion in the case of pine. Copyright © 2015. Published by Elsevier B.V.

The influence of charge stratification on the spectral signature of partially premixed combustion in a light-duty optical engine

NASA Astrophysics Data System (ADS)

Najafabadi, M. Izadi; Egelmeers, Luc; Somers, Bart; Deen, Niels; Johansson, Bengt; Dam, Nico

2017-04-01

The origin of light emission during low-temperature combustion in a light-duty IC engine is investigated by high-speed spectroscopy in both HCCI and PPC regimes. Chemiluminescence and thermal radiation are expected to be the dominant sources of light emission during combustion. A method has been developed to distinguish chemiluminescence from thermal radiation, and different chemiluminescing species could be identified. Different combustion modes and global equivalence ratios are analyzed in this manner. The results indicate that the spectral signature (270-540 nm range) of the combustion is highly dependent on the stratification level. A significant broadband chemiluminescence signal is detected and superimposed on all spectra. This broadband chemiluminescence signal can reach up to 100 percent of the total signal in HCCI combustion, while it drops to around 80 percent for stratified combustion (PPC). We show that this broadband signal can be used as a measure for the heat release rate. The broadband chemiluminescence did also correlate with the equivalence ratio quite well in both HCCI and PPC regimes, suggesting that the total emission in the spectral region of 330-400 nm can serve as a proxy of equivalence ratio and the rate of heat release. Regarding C2* chemiluminescence, we see two different chemical mechanisms for formation of C2* in the PPC regime: first during the early stage of combustion by the breakup of bigger molecules and the second during the late stage of combustion when soot particles are forming.

On-line Field Measurements of Speciated PM1 Emission Factors from Common South Asian Combustion Sources

NASA Astrophysics Data System (ADS)

DeCarlo, P. F.; Goetz, J. D.; Giordano, M.; Stockwell, C.; Maharjan, R.; Adhikari, S.; Bhave, P.; Praveen, P. S.; Panday, A. K.; Jayarathne, T. S.; Stone, E. A.; Yokelson, R. J.

2017-12-01

Characterization of aerosol emissions from prevalent but under sampled combustion sources in South Asia was performed as part of the Nepal Ambient Monitoring and Source Testing Experiment (NAMaSTE) in April 2015. Targeted emission sources included cooking stoves with a variety of solid fuels, brick kilns, garbage burning, crop-residue burning, diesel irrigation pumps, and motorcycles. Real-time measurements of submicron non-refractory particulate mass concentration and composition were obtained using an Aerodyne mini Aerosol Mass Spectrometer (mAMS). Speciated PM1 mass emission factors were calculated for all particulate species (e.g. organics, sulfates, nitrates, chlorides, ammonium) and for each source type using the carbon mass balance approach. Size resolved emission factors were also acquired using a novel high duty cycle particle time-of-flight technique (ePTOF). Black carbon and brown carbon absorption emission factors and absorption Angström exponents were measured using filter loading and scattering corrected attenuation at 370 nm and 880 nm with a dual spot aethalometer (Magee Scientific AE-33). The results indicate that open garbage burning is a strong emitter of organic aerosol, black carbon, and internally mixed particle phase hydrogen chloride (HCl). Emissions of HCl were attributed to the presence chlorinated plastics. The primarily coal fired brick kilns were found to be large emitters of sulfate but large differences in the organic and light absorbing component of emissions were observed between the two kiln types investigated (technologically advanced vs. traditional). These results, among others, bring on-line and field-tested aerosol emission measurements to an area of atmoshperic research dominated by off-line or laboratory based measurements.

[Preliminary study of source apportionment of PM10 and PM2.5 in three cities of China during spring].

PubMed

Gao, Shen; Pan, Xiao-chuan; Madaniyazi, Li-na; Xie, Juan; He, Ya-hui

2013-09-01

To study source apportionment of atmospheric PM10 (particle matter ≤ 10 µm in aerodynamic diameter) and PM2.5 (particle matter ≤ 2.5 µm in aerodynamic diameter) in Beijing,Urumqi and Qingdao, China. The atmospheric particle samples of PM10 and PM2.5 collected from Beijing between May 17th and June 18th, 2005, from Urumqi between April 20th and June 1st, 2006 and from Qingdao between April 4th and May 15th, 2005, were detected to trace the source apportionment by factor analysis and enrichment factor methods. In Beijing, the source apportionment results derived from factor analysis model for PM10 were construction dust and soil sand dust (contributing rate of variance at 45.35%), industry dust, coal-combusted smoke and vehicle emissions (contributing rate at 31.83%), and biomass burning dust (13.57%). The main pollution element was Pb, while the content (median (minimum value-maximum value)was 0.216 (0.040-0.795) µg/m(3)) . As for PM2.5, the sources were construction dust and soil sand dust (38.86%), industry dust, coal-combusted smoke and vehicle emissions (25.73%), biomass burning dust (13.10%) and burning oil dust (11.92%). The main pollution element was Zn (0.365(0.126-0.808) µg/m(3)).In Urumqi, source apportionment results for PM10 were soil sand dust and coal-combusted dust(49.75%), industry dust, vehicle emissions and secondary particles dust (30.65%). The main characteristic pollution element was Cd (0.463(0.033-1.351) ng/m(3)). As for PM2.5, the sources were soil sand dust and coal-combusted dust (43.26%), secondary particles dust (22.29%), industry dust and vehicle emissions (20.50%). The main characteristic pollution element was As (14.599 (1.696-36.741) µg/m(3)).In Qingdao, source apportionment results for PM10 were construction dust (30.91%), vehicle emissions and industry dust (29.65%) and secondary particles dust (28.99%). The main characteristic pollution element was Pb (64.071 (5.846-346.831) µg/m(3)). As for PM2.5, the sources were secondary particles dust, industry dust and vehicle emissions (49.82%) and construction dust (33.71%). The main characteristic pollution element was Pb(57.340 (5.004-241.559) µg/m(3)).Enrichment factors of Zn, Pb, As and Cd in PM2.5 were higher than those in PM10 both in Beijing and Urumqi. The major sources of the atmospheric particles PM10 and PM2.5 in Beijing were cement dust from construction sites and sand dust from soil; while the major sources of those in Urumqi were pollution by smoke and sand dust from burning coal. The major sources of the atmospheric particles PM10 in Qingdao were cement dust from construction sites; however, the major sources of PM2.5 there were secondary particles dust, industry dust and vehicle emissions. According to our study, the heavy metal elements were likely to gather in PM2.5.

Influences of diesel pilot injection on ethanol autoignition - a numerical analysis

NASA Astrophysics Data System (ADS)

Burnete, N. V.; Burnete, N.; Jurchis, B.; Iclodean, C.

2017-10-01

The aim of this study is to highlight the influences of the diesel pilot quantity as well as the timing on the autoignition of ethanol and the pollutant emissions resulting from the combustion process. The combustion concept presented in this paper requires the injection of a small quantity of diesel fuel in order to create the required autoignition conditions for ethanol. The combustion of the diesel droplets injected in the combustion chamber lead to the creation of high temperature locations that favour the autoignition of ethanol. However, due to the high vaporization enthalpy and the better distribution inside the combustion chamber of ethanol, the peak temperature values are reduced. Due to the lower temperature values and the high burning velocity of ethanol (combined with the fact that there are multiple ignition sources) the conditions required for the formation of nitric oxides are not achieved anymore, thus leading to significantly lower NOx emissions. This way the benefits of the Diesel engine and of the constant volume combustion are combined to enable a more efficient and environmentally friendly combustion process.

An investigation of late-combustion soot burnout in a DI diesel engine using simultaneous planar imaging of soot and OH radical

DOE Office of Scientific and Technical Information (OSTI.GOV)

John E. Dec; Peter L. Kelly-Zion

Diesel engine design continues to be driven by the need to improve performance while at the same time achieving further reductions in emissions. The development of new designs to accomplish these goals requires an understanding of how the emissions are produced in the engine. Laser-imaging diagnostics are uniquely capable of providing this information, and the understanding of diesel combustion and emissions formation has been advanced considerably in recent years by their application. However, previous studies have generally focused on the early and middle stages of diesel combustion. These previous laser-imaging studies do provide important insight into the soot formation andmore » oxidation processes during the main combustion event. They indicate that prior to the end of injection, soot formation is initiated by fuel-rich premixed combustion (equivalence ratio > 4) near the upstream limit of the luminous portion of the reacting fuel jet. The soot is then oxidized at the diffusion flame around the periphery of the luminous plume. Under typical diesel engine conditions, the diffusion flame does not burn the remaining fuel and soot as rapidly as it is supplied, resulting in an expanding region of rich combustion products and soot. This is evident in natural emission images by the increasing size of the luminous soot cloud prior to the end of injection. Hence, the amount of soot in the combustion chamber typically increases until shortly after the end of fuel injection, at which time the main soot formation period ends and the burnout phase begins. Sampling valve and two-color pyrometry data indicate that the vast majority (more than 90%) of the soot formed is oxidized before combustion ends; however, it is generally thought that a small fraction of this soot from the main combustion zones is not consumed and is the source of tail pipe soot emissions.« less

The seasonal changes and spatial trends of particle-associated polycyclic aromatic hydrocarbons in the summer and autumn in Changsha city

NASA Astrophysics Data System (ADS)

Yang, Fang; Zhai, YunBo; Chen, Lin; Li, CaiTing; Zeng, GuangMing; He, YiDe; Fu, ZongMin; Peng, WenFeng

2010-04-01

16 Polycyclic aromatic hydrocarbons (PAHs) in TSP were identified and quantified in samples collected during May and September of 2008, in Changsha, on three different sites: the city environmental protection agency of Changsha (A), the Middle School Attached to Hunan Normal University (B) and Yuhua district (C). The filters contained the particulate matter were extracted with dichloromethane in ultrasonic bath and then analyzed by gas chromatography/mass spectrometry (GC/MS). The total of 16 PAHs mean concentrations of summer at site A, B, C were 32.503 ng/m 3 , 19.360 ng/m 3 and 26.784 ng/m 3, respectively; while the values for autumn at site A, B, C were 24.982 ng/m 3, 17.088 ng/m 3 and 15.465 ng/m 3, respectively. The mean concentrations of PAHs of all samples in A site were 0.57 times higher than those measured at B site, and 0.38 times higher than at C site. The analysis of their distribution amongst the main emission sources was done through the diagnosis of concentration ratios of PAHs, as well as using statistical methods like principal component analysis. The diagnosis results of concentration ratios of PAHs suggested that the major polluting sources in the Changsha region during the studied period were the combustion of fuels, such as diesel oil, gasoline, wood and coal. The statistical analysis separated the 16 compounds studied into 3 and 4 factors for summer and autumn, separately. Factor 1 in summer represents vehicular emissions. Factor 2 represents emissions from the nature gas. Factor 3 represents emissions from combustion. In autumn, vehicle emissions, combustion sources, natural gas and coke oven were the major emissions.

Climate Forcing by Particles from Specific Sources, With Implications for No-regrets Scenarios

NASA Astrophysics Data System (ADS)

Bond, T. C.; Roden, C. A.; Subramanian, R.; Rasch, P. J.

2006-12-01

Mitigation-- the act of reducing human effects on climate and atmosphere by changing practices-- occurs one source at a time, one country at a time. Examining climate forcing produced by individual sources could be instructive. Two sectors contribute the largest fraction of black carbon aerosols from energy-related combustion: diesel engines and residential biofuel. We examine direct climate forcing by aerosols from these sources in four locations. Because source characterization is lacking, global emission inventories that include chemical composition of particles have often relied on expert judgment. We are gaining information on emission rates and climate- relevant properties through partnerships with projects related to air quality and health in Thailand and Honduras. Despite the presence of organic carbon, black carbon's constant companion, particles from both diesel and biofuel exert net climate warming. In particular, solid-fuel combustion produces material with weak light absorption and strong absorption spectral dependence. We discuss the expected emissions and properties of this material. Revised emission rates and properties are implemented in the Community Atmosphere Model, housed at the National Center for Atmospheric Research, and we tag particles emitted from individual sources. Which sources feed high-forcing regions, such as the area above the low-cloud deck in the North Pacific? Which particles might have been scavenged, and how does uncertainty in removal rates affect single-source forcing? Using model experiments, we estimate central values and uncertainties of direct radiative forcing from each source. Finally, we discuss the potential for reducing climate forcing by mitigating these individual sources. What is the range of benefits expected by addressing these sources, and what are the costs and obstacles? Only by representing uncertainty can we determine the likelihood that reducing these emissions represents a "no- regret" scenario for climate.

Time-resolved analysis of particle emissions from residential biomass combustion - Emissions of refractory black carbon, PAHs and organic tracers

NASA Astrophysics Data System (ADS)

Nielsen, Ingeborg E.; Eriksson, Axel C.; Lindgren, Robert; Martinsson, Johan; Nyström, Robin; Nordin, Erik Z.; Sadiktsis, Ioannis; Boman, Christoffer; Nøjgaard, Jacob K.; Pagels, Joakim

2017-09-01

Time-resolved particle emissions from a conventional wood stove were investigated with aerosol mass spectrometry to provide links between combustion conditions, emission factors, mixing state of refractory black carbon and implications for organic tracer methods. The addition of a new batch of fuel results in low temperature pyrolysis as the fuel heats up, resulting in strong, short-lived, variable emission peaks of organic aerosol-containing markers of anhydrous sugars, such as levoglucosan (fragment at m/z 60). Flaming combustion results in emissions dominated by refractory black carbon co-emitted with minor fractions of organic aerosol and markers of anhydrous sugars. Full cycle emissions are an external mixture of larger organic aerosol-dominated and smaller thinly coated refractory black carbon particles. A very high burn rate results in increased full cycle mass emission factors of 66, 2.7, 2.8 and 1.3 for particulate polycyclic aromatic hydrocarbons, refractory black carbon, total organic aerosol and m/z 60, respectively, compared to nominal burn rate. Polycyclic aromatic hydrocarbons are primarily associated with refractory black carbon-containing particles. We hypothesize that at very high burn rates, the central parts of the combustion zone become air starved, leading to a locally reduced combustion temperature that reduces the conversion rates from polycyclic aromatic hydrocarbons to refractory black carbon. This facilitates a strong increase of polycyclic aromatic hydrocarbons emissions. At nominal burn rates, full cycle emissions based on m/z 60 correlate well with organic aerosol, refractory black carbon and particulate matter. However, at higher burn rates, m/z 60 does not correlate with increased emissions of polycyclic aromatic hydrocarbons, refractory black carbon and organic aerosol in the flaming phase. The new knowledge can be used to advance source apportionment studies, reduce emissions of genotoxic compounds and model the climate impacts of refractory black carbon, such as absorption enhancement by lensing.

Spatial and temporal source apportionment of PM2.5 in Georgia, 2002 to 2013

NASA Astrophysics Data System (ADS)

Zhai, Xinxin; Mulholland, James A.; Russell, Armistead G.; Holmes, Heather A.

2017-07-01

The Chemical Mass Balance (CMB) receptor model was applied to estimate PM2.5 source impacts over Georgia from 2002 to 2013 using ambient PM2.5 species concentration data from 13 sites. Measurements of 19 PM2.5 species were used as inputs along with measurement-based source profiles to estimate the impacts of nine sources, including both primary components (from heavy duty diesel vehicle, light duty gasoline vehicle, biomass burning, coal combustion, and suspended dust sources) and secondary pollutants (ammonium sulfate, ammonium bisulfate, ammonium nitrate, and secondary organic carbon). From 2002 to 2013, PM2.5 total mass decreased from 13.8 μg/m3 to 9.2 μg/m3 averaged across all sites, a 33% decrease. Largest decreases were observed for secondary sulfate and nitrate species (58% and 44%, respectively). The amount of neutralization by ammonium did not change substantially over the time period in spite of substantial decreases in sulfate and nitrate concentrations. Total mobile source impacts decreased more at urban sites (39%) than rural sites (23%), whereas biomass burning decreased more at rural sites (34%) than urban sites (27%). The estimated central-site source impacts are found to spatially represent large areas for secondary pollutants, smaller areas for biomass burning and dust, and very local areas for mobile sources and coal combustion. Trends from the National Emissions Inventory were compared with the annual trends of mobile source impacts, coal combustion impacts, and sulfate concentrations, resulting in statistically significant positive trends with Pearson R2 of 0.80, 0.64, and 0.79, respectively. Results presented here suggest that PM2.5 reductions in Georgia and the Southeast have been achieved by control of both stationary and mobile sources, and that PM2.5 is comprised of increasing fractions of biomass burning emissions and suspended dust. The temporal trends of source impacts at each site adds information about source changes beyond the every-three-year emission inventories for evaluation of emission-based model results.

Source profiles and contributions of biofuel combustion for PM2.5, PM10 and their compositions, in a city influenced by biofuel stoves.

PubMed

Tian, Ying-Ze; Chen, Jia-Bao; Zhang, Lin-Lin; Du, Xin; Wei, Jin-Jin; Fan, Hui; Xu, Jiao; Wang, Hai-Ting; Guan, Liao; Shi, Guo-Liang; Feng, Yin-Chang

2017-12-01

Source and ambient samples were collected in a city in China that uses considerable biofuel, to assess influence of biofuel combustion and other sources on particulate matter (PM). Profiles and size distribution of biofuel combustion were investigated. Higher levels in source profiles, a significant increase in heavy-biomass ambient and stronger correlations of K + , Cl - , OC and EC suggest that they can be tracers of biofuel combustion. And char-EC/soot-EC (8.5 for PM 2.5 and 15.8 for PM 10 of source samples) can also be used to distinguish it. In source samples, water-soluble organic carbon (WSOC) were approximately 28.0%-68.8% (PM 2.5 ) and 27.2%-43.8% (PM 10 ) of OC. For size distribution, biofuel combustion mainly produces smaller particles. OC1, OC2, EC1 and EC2 abundances showed two peaks with one below 1 μm and one above 2 μm. An advanced three-way factory analysis model was applied to quantify source contributions to ambient PM 2.5 and PM 10 . Higher contributions of coal combustion, vehicular emission, nitrate and biofuel combustion occurred during the heavy-biomass period, and higher contributions of sulfate and crustal dust were observed during the light-biomass period. Mass and percentage contributions of biofuel combustion were significantly higher in heavy-biomass period. The biofuel combustion attributed above 45% of K + and Cl - , above 30% of EC and about 20% of OC. In addition, through analysis of source profiles and contributions, they were consistently evident that biofuel combustion and crustal dust contributed more to cation than to anion, while sulfate & SOC and nitrate showed stronger influence on anion than on cation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Oxidative Stress, Inflammatory Biomarkers and Toxicity in Mouse Lung and Liver after Inhalation Exposure to 100% Biodiesel or Petroleum Diesel Emissions

EPA Science Inventory

BACKGROUND: Over the past decade, biodiesel (BD) has become a first alternative energy source that is economically viable and meets requirements of the Clean Air Act. Due to lower mass emissions and reduced hazardous compounds compared to diesel combustion emissions (CE), BD expo...

40 CFR 60.4345 - What are the requirements for the continuous emission monitoring system equipment, if I choose to...

Code of Federal Regulations, 2010 CFR

2010-07-01

... continuous emission monitoring system equipment, if I choose to use this option? 60.4345 Section 60.4345... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4345 What are the requirements for the continuous emission monitoring system equipment, if I...

40 CFR 60.4345 - What are the requirements for the continuous emission monitoring system equipment, if I choose to...

Code of Federal Regulations, 2011 CFR

2011-07-01

... continuous emission monitoring system equipment, if I choose to use this option? 60.4345 Section 60.4345... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4345 What are the requirements for the continuous emission monitoring system equipment, if I...

40 CFR 98.112 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GREENHOUSE GAS REPORTING Ferroalloy Production § 98.112 GHGs to report. You must report: (a) Process CO2... Table K-1 to subpart K. (b) CO2, CH4, and N2O emissions from each stationary combustion unit following... part (General Stationary Fuel Combustion Sources). [74 FR 56374, Oct. 30, 2009, as amended at 75 FR...

40 CFR 98.112 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GREENHOUSE GAS REPORTING Ferroalloy Production § 98.112 GHGs to report. You must report: (a) Process CO2... Table K-1 to subpart K. (b) CO2, CH4, and N2O emissions from each stationary combustion unit following... part (General Stationary Fuel Combustion Sources). [74 FR 56374, Oct. 30, 2009, as amended at 75 FR...

40 CFR 98.112 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GREENHOUSE GAS REPORTING Ferroalloy Production § 98.112 GHGs to report. You must report: (a) Process CO2... Table K-1 to subpart K. (b) CO2, CH4, and N2O emissions from each stationary combustion unit following... part (General Stationary Fuel Combustion Sources). [74 FR 56374, Oct. 30, 2009, as amended at 75 FR...

40 CFR 98.112 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GREENHOUSE GAS REPORTING Ferroalloy Production § 98.112 GHGs to report. You must report: (a) Process CO2... Table K-1 to subpart K. (b) CO2, CH4, and N2O emissions from each stationary combustion unit following... part (General Stationary Fuel Combustion Sources). [74 FR 56374, Oct. 30, 2009, as amended at 75 FR...

SOA FORMATION FROM THE IRRADIATION OF A-PINENE-NOX IN THE ABSENCE AND PRESENCE OF SULFUR DIOXIDE

EPA Science Inventory

Sulfur dioxide (SO2) is an important constituent in the polluted atmosphere. It is emitted from combustion sources using fuels that contain sulfur. Emissions of SO2 in the United States were reportedly 17 Tg in 1996 with most coming from coal and petroleum combustion. The pr...

40 CFR 60.2145 - How do I demonstrate continuous compliance with the emission limitations and the operating limits?

Code of Federal Regulations, 2013 CFR

2013-07-01

... NEW STATIONARY SOURCES Standards of Performance for Commercial and Industrial Solid Waste Incineration... own or operate an existing commercial or industrial combustion unit that combusted a fuel or non-waste... internal and external corrosion. (3) Use a pressure sensor with a minimum tolerance of 1.27 centimeters of...

40 CFR 60.2145 - How do I demonstrate continuous compliance with the emission limitations and the operating limits?

Code of Federal Regulations, 2014 CFR

2014-07-01

... NEW STATIONARY SOURCES Standards of Performance for Commercial and Industrial Solid Waste Incineration... own or operate an existing commercial or industrial combustion unit that combusted a fuel or non-waste... external corrosion. (3) Use a pressure sensor with a minimum tolerance of 1.27 centimeters of water or a...

Modelling urban δ13C variations in the Greater Toronto Area

NASA Astrophysics Data System (ADS)

Pugliese, S.; Vogel, F. R.; Murphy, J. G.; Worthy, D. E. J.; Zhang, J.; Zheng, Q.; Moran, M. D.

2015-12-01

Even in urbanized regions, carbon dioxide (CO2) emissions are derived from a variety of biogenic and anthropogenic sources and are influenced by atmospheric transport across borders. As policies are introduced to reduce the emission of CO2, there is a need for independent verification of emissions reporting. In this work, we aim to use carbon isotope (13CO2 and 12CO2) simulations in combination with atmospheric measurements to distinguish between CO2 sources in the Greater Toronto Area (GTA), Canada. This is being done by developing an urban δ13C framework based on existing CO2 emission data and forward modelling using a chemistry transport model, CHIMERE. The framework is designed to use region specific δ13C signatures of the dominant CO2 sources together with a CO2 inventory at a fine spatial and temporal resolution; the product is compared against highly accurate 13CO2 and 12CO2 ambient data. The strength of this framework is its potential to estimate both locally produced and regionally transported CO­2. Locally, anthropogenic CO­2 in urban areas is often derived from natural gas combustion (for heating) and gasoline/diesel combustion (for transportation); the isotopic signatures of these processes are significantly different (approximately d13CVPDB = -40 ‰ and -26 ‰ respectively) and can be used to infer their relative contributions. Furthermore, the contribution of transported CO2 can also be estimated as nearby regions often rely on other sources of heating (e.g. coal combustion), which has a very different signature (approximately d13CVPDB = -23 ‰). We present an analysis of the GTA in contrast to Paris, France where atmospheric observations are also available and 13CO2 has been studied. Utilizing our δ13C framework and differences in sectoral isotopic signatures, we quantify the relative contribution of CO2 sources on the overall measured concentration and assess the ability of this framework as a tool for tracing the evolution of sector-specific emissions.

[Inventories of atmospheric arsenic emissions from coal combustion in China, 2005].

PubMed

Tian, He-Zhong; Qu, Yi-Ping

2009-04-15

Anthropogenic arsenic (As) emitted from coal combustion is one of key trace elements leading to negative air pollution and national economy loss. It is of great significance to estimate the atmospheric arsenic emission for proposing relevant laws or regulations and selecting proper pollution control technologies. The inventories of atmospheric arsenic emissions from coal combustion in China were evaluated by adopting the emission factor method based on fuel consumption. Arsenic emission sources were firstly classified into several categories by economic sectors, combustion types and pollution control technologies. Then, according to provincial coal consumption and averaged arsenic concentration in the feed fuel, the inventories of atmospheric arsenic emission from coal combustion in China in 2005 were established. Coal outputand consumption in China in 2005 were 2,119.8 and 2,099.8 Mt, respectively. The total emissions of arsenic released into the atmosphere in 2005 in China were estimated at about 1,564.4 t, and Shandong ranked the largest province with 144.4 t arsenic release, followed by Hunan (141.1 t), Hebei (108.5 t), Henan (77.7 t), and Jiangsu (77.0 t), which were mainly concentrated in the eastern and central provinces of China. The arsenic emissions were largely emitted by industry sector (818.8 t) and thermal power generation sector (303.4 t), contributing 52.3% and 19.4% of the totals, respectively. About 375.5 t arsenic was estimated to be released into the atmosphere in the form of gas phase in China in 2005, with a share of 24% of the totals. In general, arsenic pollution control from coal combustion should be highlighted for the power and industry sectors in the whole country. However, arsenic poisoning caused by residential coal burning should also be paid great attention in some areas such as Xinjiang, Gansu, Qinghai and Guishou.

Nepal Ambient Monitoring and Source Testing Experiment (NAMaSTE): Emissions of particulate matter from wood and dung cooking fires, brick kilns, generators, trash and crop residue burning

NASA Astrophysics Data System (ADS)

Stone, Elizabeth; Jayarathne, Thilina; Stockwell, Chelsea; Christian, Ted; Bhave, Prakash; Siva Praveen, Puppala; Panday, Arnico; Adhikari, Sagar; Maharjan, Rashmi; Goetz, Doug; DeCarlo, Peter; Saikawa, Eri; Yokelson, Robert

2016-04-01

The Nepal Ambient Monitoring and Source Testing Experiment (NAMASTE) field campaign targeted the in situ characterization of widespread and under-sampled combustion sources. In Kathmandu and the Terai, southern Nepal's flat plains, samples of fine particulate matter (PM2.5) were collected from wood and dung cooking fires (n = 22), generators (n = 2), groundwater pumps (n = 2), clamp kilns (n = 3), zig-zag kilns (n = 3), trash burning (n = 4), one heating fire, and one crop residue fire. Co-located measurements of carbon dioxide, carbon monoxide, and volatile organic compounds allowed for the application of the carbon mass balance approach to estimate emission factors for PM2.5, elemental carbon, organic carbon, and water-soluble inorganic ions. Organic matter was chemically speciated using gas chromatography - mass spectrometry for polycyclic aromatic hydrocarbons, sterols, n-alkanes, hopanes, steranes, and levoglucosan, which accounted for 2-8% of the measured organic carbon. These data were used to develop molecular-marker based profiles for use in source apportionment modeling. This study provides quantitative emission factors for particulate matter and its constituents for many important combustion sources in Nepal and South Asia.

Retene Emission from Residential Solid Fuels in China and Evaluation of Retene as a Unique Marker for Soft Wood Combustion

PubMed Central

Shen, Guofeng; Tao, Shu; Wei, Siye; Zhang, Yanyan; Wang, Rong; Wang, Bin; Li, Wei; Shen, Huizhong; Huang, Ye; Yang, Yifeng; Wang, Wei; Wang, Xilong; Massey Simonich, Staci L.

2012-01-01

Retene (1-methyl-7-isopropylphenanthrene) is often used as a marker for softwood combustion and for polycyclic aromatic hydrocarbon (PAH) source apportionment. The emission factors of retene (EFRET) from 11 crop residues, 27 firewood and 5 coals were measured using traditional rural Chinese stoves. Retene was measured in combustion emissions from all of the residential fuels tested and EFRET varied significantly among the fuels due to the differences in fuel properties and combustion conditions. EFRET for pine (0.34±0.08 mg/kg) and larch (0.29±0.22 mg/kg) were significantly higher than those of other wood types, including fir and cypress (0.081±0.058 mg/kg). However, EFRET for crop residues varied from 0.048±0.008 to 0.37±0.14 mg/kg and were not significantly lower than those for softwood (0.074±0.026 to 0.34±0.08 mg/kg). The EFRET for coal were very high and ranged from 2.2±1.5 (anthracite briquette) to 187±113 mg/kg (raw bituminous chunk). EFRET was positively correlated with EFs of co-emitted particulate matter (EFPM) and phenanthrene (EFPHE) for crop residue and coal, but not for wood. In addition, the ratios of EFPHE/EFRET and EFPM/EFRET for coals were much lower than those for crop residues and wood. These data suggest that retene is not a unique PAH marker for softwood combustion and that coal combustion, in particular, should be taken into account when retene is used for PAH source apportionment. PMID:22452486

Low emission U-fired boiler combustion system

DOEpatents

Ake, Terence; Beittel, Roderick; Lisauskas, Robert A.; Reicker, Eric

2000-01-01

At least one main combustion chamber contains at least one pulverized coal burner. Each pulverized coal burner is operatively arranged for minimizing NO.sub.X production and for maintaining a predetermined operating temperature to liquefy ash within the combustion chamber. The combustion chamber includes a slag drain for removing slag from the combustion chamber. A slag screen is positioned in a generally U-shaped furnace flow pattern. The slag screen is positioned between the combustion chamber and a radiant furnace. The radiant furnace includes a reburning zone for in-furnace No.sub.X reduction. The reburning zone extends between a reburning fuel injection source and at least one overfire air injection port for injecting air.

Changes in concentration, composition and source contribution of atmospheric organic aerosols by shifting coal to natural gas in Urumqi

NASA Astrophysics Data System (ADS)

Ren, Yanqin; Wang, Gehui; Wu, Can; Wang, Jiayuan; Li, Jianjun; Zhang, Lu; Han, Yanni; Liu, Lang; Cao, Cong; Cao, Junji; He, Qing; Liu, Xinchun

2017-01-01

Size-segregated aerosols were collected in Urumqi, a megacity in northwest China, during two heating seasons, i.e., before (heating season І: January-March 2012) and after (heating season II: January-March 2014) the project "shifting coal to natural gas", and determined for n-alkanes, PAHs and oxygenated PAHs to investigate the impact of replacement of coal by natural gas on organic aerosols in the urban atmosphere. Our results showed that compared to those in heating season I concentrations of n-alkanes, PAHs and OPAHs decreased by 74%, 74% and 82% in heating season II, respectively. Source apportionment analysis suggested that coal combustion, traffic emission and biomass burning are the major sources of the determined organics during the heating seasons in Urumqi. Traffic emission is the main source for n-alkanes in the city. Coal combustion is the dominant source of PAHs and OPAHs in heating season І, but traffic emission becomes their major source in heating season ІI. Relative contributions of coal combustion to n-alkanes, PAHs and OPAHs in Urumqi decreased from 21 to 75% in heating season I to 4.0-21% in heating season II due to the replacement of coal with natural gas for house heating. Health risk assessment further indicated that compared with that in heating season I the number of lung cancer related to PAHs exposure in Urumqi decreased by 73% during heating season II due to the project implementation. Our results suggest that replacing coal by clean energy sources for house heating will significantly mitigate air pollution and improve human health in China.

Nepal Ambient Monitoring and Source Testing Experiment (NAMaSTE): emissions of particulate matter from wood- and dung-fueled cooking fires, garbage and crop residue burning, brick kilns, and other sources

NASA Astrophysics Data System (ADS)

Jayarathne, Thilina; Stockwell, Chelsea E.; Bhave, Prakash V.; Praveen, Puppala S.; Rathnayake, Chathurika M.; Robiul Islam, Md.; Panday, Arnico K.; Adhikari, Sagar; Maharjan, Rashmi; Goetz, J. Douglas; DeCarlo, Peter F.; Saikawa, Eri; Yokelson, Robert J.; Stone, Elizabeth A.

2018-02-01

The Nepal Ambient Monitoring and Source Testing Experiment (NAMaSTE) characterized widespread and under-sampled combustion sources common to South Asia, including brick kilns, garbage burning, diesel and gasoline generators, diesel groundwater pumps, idling motorcycles, traditional and modern cooking stoves and fires, crop residue burning, and heating fire. Fuel-based emission factors (EFs; with units of pollutant mass emitted per kilogram of fuel combusted) were determined for fine particulate matter (PM2.5), organic carbon (OC), elemental carbon (EC), inorganic ions, trace metals, and organic species. For the forced-draft zigzag brick kiln, EFPM2.5 ranged from 12 to 19 g kg-1 with major contributions from OC (7 %), sulfate expected to be in the form of sulfuric acid (31.9 %), and other chemicals not measured (e.g., particle-bound water). For the clamp kiln, EFPM2.5 ranged from 8 to 13 g kg-1, with major contributions from OC (63.2 %), sulfate (23.4 %), and ammonium (16 %). Our brick kiln EFPM2.5 values may exceed those previously reported, partly because we sampled emissions at ambient temperature after emission from the stack or kiln allowing some particle-phase OC and sulfate to form from gaseous precursors. The combustion of mixed household garbage under dry conditions had an EFPM2.5 of 7.4 ± 1.2 g kg-1, whereas damp conditions generated the highest EFPM2.5 of all combustion sources in this study, reaching up to 125 ± 23 g kg-1. Garbage burning emissions contained triphenylbenzene and relatively high concentrations of heavy metals (Cu, Pb, Sb), making these useful markers of this source. A variety of cooking stoves and fires fueled with dung, hardwood, twigs, and/or other biofuels were studied. The use of dung for cooking and heating produced higher EFPM2.5 than other biofuel sources and consistently emitted more PM2.5 and OC than burning hardwood and/or twigs; this trend was consistent across traditional mud stoves, chimney stoves, and three-stone cooking fires. The comparisons of different cooking stoves and cooking fires revealed the highest PM emissions from three-stone cooking fires (7.6-73 g kg-1), followed by traditional mud stoves (5.3-19.7 g kg-1), mud stoves with a chimney for exhaust (3.0-6.8 g kg-1), rocket stoves (1.5-7.2 g kg-1), induced-draft stoves (1.2-5.7 g kg-1), and the bhuse chulo stove (3.2 g kg-1), while biogas had no detectable PM emissions. Idling motorcycle emissions were evaluated before and after routine servicing at a local shop, which decreased EFPM2.5 from 8.8 ± 1.3 to 0.71 ± 0.45 g kg-1 when averaged across five motorcycles. Organic species analysis indicated that this reduction in PM2.5 was largely due to a decrease in emission of motor oil, probably from the crankcase. The EF and chemical emissions profiles developed in this study may be used for source apportionment and to update regional emission inventories.

Vapor hydrogen and oxygen isotopes reflect water of combustion in the urban atmosphere

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorski, Galen; Strong, Courtenay; Good, Stephen P.

Anthropogenic modification of the water cycle involves a diversity of processes, many of which have been studied intensively using models and observations. Some effective tools for measuring the contribution and fate of combustion-derived water vapor in the atmosphere are lacking, however, and this flux has received relatively little attention. We provide theoretical estimates and a first set of measurements demonstrating that water of combustion is characterized by a distinctive combination of H and O isotope ratios. Furthermore, we show that during periods of relatively low humidity and/or atmospheric stagnation, this isotopic signature can be used to quantify the concentration ofmore » water of combustion in the atmospheric boundary layer over Salt Lake City. Combustion-derived vapor concentrations vary between periods of atmospheric stratification and mixing, both on multiday and diurnal timescales, and respond over periods of hours to variations in surface emissions. Our estimates suggest that up to 13% of the boundary layer vapor during the period of study was derived from combustion sources, and both the temporal pattern and magnitude of this contribution were closely reproduced by an independent atmospheric model forced with a fossil fuel emissions data product. These findings suggest potential for water vapor isotope ratio measurements to be used in conjunction with other tracers to refine the apportionment of urban emissions, and imply that water vapor emissions associated with combustion may be a significant component of the water budget of the urban boundary layer, with potential implications for urban climate, ecohydrology, and photochemistry.« less

Vapor hydrogen and oxygen isotopes reflect water of combustion in the urban atmosphere

DOE PAGES

Gorski, Galen; Strong, Courtenay; Good, Stephen P.; ...

2015-03-02

Anthropogenic modification of the water cycle involves a diversity of processes, many of which have been studied intensively using models and observations. Some effective tools for measuring the contribution and fate of combustion-derived water vapor in the atmosphere are lacking, however, and this flux has received relatively little attention. We provide theoretical estimates and a first set of measurements demonstrating that water of combustion is characterized by a distinctive combination of H and O isotope ratios. Furthermore, we show that during periods of relatively low humidity and/or atmospheric stagnation, this isotopic signature can be used to quantify the concentration ofmore » water of combustion in the atmospheric boundary layer over Salt Lake City. Combustion-derived vapor concentrations vary between periods of atmospheric stratification and mixing, both on multiday and diurnal timescales, and respond over periods of hours to variations in surface emissions. Our estimates suggest that up to 13% of the boundary layer vapor during the period of study was derived from combustion sources, and both the temporal pattern and magnitude of this contribution were closely reproduced by an independent atmospheric model forced with a fossil fuel emissions data product. These findings suggest potential for water vapor isotope ratio measurements to be used in conjunction with other tracers to refine the apportionment of urban emissions, and imply that water vapor emissions associated with combustion may be a significant component of the water budget of the urban boundary layer, with potential implications for urban climate, ecohydrology, and photochemistry.« less

Air quality in the German-Czech border region: A focus on harmful fractions of PM and ultrafine particles

NASA Astrophysics Data System (ADS)

Schladitz, Alexander; Leníček, Jan; Beneš, Ivan; Kováč, Martin; Skorkovský, Jiří; Soukup, Aleš; Jandlová, Jana; Poulain, Laurent; Plachá, Helena; Löschau, Gunter; Wiedensohler, Alfred

2015-12-01

A comprehensive air quality study has been carried out at two urban background sites in Annaberg-Buchholz (Germany) and Ústí nad Labem (Czech Republic) in the German-Czech border region between January 2012 and June 2014. Special attention was paid to quantify harmful fractions of particulate matter (PM) and ultrafine particle number concentration (UFP) from solid fuel combustion and vehicular traffic. Source type contributions of UFP were quantified by using the daily concentration courses of UFP and nitrogen oxide. Two different source apportionment techniques were used to quantify relative and absolute mass contributions: positive matrix factorization for total PM2.5 and elemental carbon in PM2.5 and chemical mass balance for total PM1 and organic carbon in PM1. Contributions from solid fuel combustion strongly differed between the non-heating period (April-September) and the heating period (October-March). Major sources of solid fuel combustion in this study were wood and domestic coal combustion, while the proportion of industrial coal combustion was low (<3%). In Ústí nad Labem combustion of domestic brown coal was the most important source of organic carbon ranging from 34% to 43%. Wood combustion was an important source of organic carbon in Annaberg-Buchholz throughout the year. Heavy metals and less volatile polycyclic aromatic hydrocarbons (PAH) in the accumulation mode were related to solid fuel combustion with enhanced concentrations during the heating period. In contrast, vehicular PAH emissions were allocated to the Aitken mode. Only in Ústí nad Labem a significant contribution of photochemical new particle formation (e.g. from sulfur dioxide) to UFP of almost 50% was observed during noontime. UFPs from traffic emissions (nucleation particles) and primary emitted soot particles dominated at both sites during the rest of the day. The methodology of a combined source apportionment of UFP and PM can be adapted to other regions of the world with similar problems of atmospheric pollution to calculate the relative risk in epidemiological health studies for different sub-fractions of PM and UFP. This will enhance the meaningfulness of published relative risks in health studies based on total PM and UFP number concentrations.

Untargeted Identification of Wood Type-Specific Markers in Particulate Matter from Wood Combustion.

PubMed

Weggler, Benedikt A; Ly-Verdu, Saray; Jennerwein, Maximilian; Sippula, Olli; Reda, Ahmed A; Orasche, Jürgen; Gröger, Thomas; Jokiniemi, Jorma; Zimmermann, Ralf

2016-09-20

Residential wood combustion emissions are one of the major global sources of particulate and gaseous organic pollutants. However, the detailed chemical compositions of these emissions are poorly characterized due to their highly complex molecular compositions, nonideal combustion conditions, and sample preparation steps. In this study, the particulate organic emissions from a masonry heater using three types of wood logs, namely, beech, birch, and spruce, were chemically characterized using thermal desorption in situ derivatization coupled to a GCxGC-ToF/MS system. Untargeted data analyses were performed using the comprehensive measurements. Univariate and multivariate chemometric tools, such as analysis of variance (ANOVA), principal component analysis (PCA), and ANOVA simultaneous component analysis (ASCA), were used to reduce the data to highly significant and wood type-specific features. This study reveals substances not previously considered in the literature as meaningful markers for differentiation among wood types.

Fossil and Nonfossil Sources of Organic and Elemental Carbon Aerosols in the Outflow from Northeast China.

PubMed

Zhang, Yan-Lin; Kawamura, Kimitaka; Agrios, Konstantinos; Lee, Meehye; Salazar, Gary; Szidat, Sönke

2016-06-21

Source quantification of carbonaceous aerosols in the Chinese outflow regions still remains uncertain despite their high mass concentrations. Here, we unambiguously quantified fossil and nonfossil contributions to elemental carbon (EC) and organic carbon (OC) of total suspended particles (TSP) from a regional receptor site in the outflow of Northeast China using radiocarbon measurement. OC and EC concentrations were lower in summer, representing mainly marine air, than in other seasons, when air masses mostly traveled over continental regions in Mongolia and northeast China. The annual-mean contribution from fossil-fuel combustion to EC was 76 ± 11% (0.1-1.3 μg m(-3)). The remaining 24 ± 11% (0.03-0.42 μg m(-3)) was attributed to biomass burning, with slightly higher contribution in the cold period (∼31%) compared to the warm period (∼21%) because of enhanced emissions from regional biomass combustion sources in China. OC was generally dominated by nonfossil sources, with an annual average of 66 ± 11% (0.5-2.8 μg m(-3)), approximately half of which was apportioned to primary biomass-burning sources (34 ± 6%). In winter, OC almost equally originated from primary OC (POC) emissions and secondary OC (SOC) formation from fossil fuel and biomass-burning sources. In contrast, summertime OC was dominated by primary biogenic emissions as well as secondary production from biogenic and biomass-burning sources, but fossil-derived SOC was the smallest contributor. Distinction of POC and SOC was performed using primary POC-to-EC emission ratios separated for fossil and nonfossil emissions.

DEVELOPMENT OF REAL-TIME FLARE COMBUSTION EFFICIENCY MONITOR - PHASE I

EPA Science Inventory

There are approximately 7,000 flares in operation at industrial facilities across the United States. Flares are one of the largest Volatile Organic Compounds (VOCs) and air toxics emissions sources. Based on a special emission inventory required by the Texas Commission on E...

40 CFR 60.1250 - What is my schedule for evaluating continuous emission monitoring systems?

Code of Federal Regulations, 2010 CFR

2010-07-01

... continuous emission monitoring systems? 60.1250 Section 60.1250 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced...

Specifics of phytomass combustion in small experimental device

NASA Astrophysics Data System (ADS)

Lenhard, Richard; Mičieta, Jozef; Jandačka, Jozef; Gavlas, Stanislav

2015-05-01

A wood pellet combustion carries out with high efficiency and comfort in modern pellet boilers. These facts help to increase the amount of installed pellet boilers in households. The combustion process quality depends besides the combustion conditions also on the fuel quality. The wood pellets, which don`t contain the bark and branches represent the highest quality. Because of growing pellet demand, an herbal biomass (phytomass), which is usually an agricultural by-product becomes economically attractive for pellet production. Although the phytomass has the net calorific value relatively slightly lower than the wood biomass, it is often significantly worse in view of the combustion process and an emission production. The combustion of phytomass pellets causes various difficulties in small heat sources, mainly due to a sintering of fuel residues. We want to avoid the ash sintering by a lowering of temperature in the combustion chamber below the ash sintering temperature of phytomass via the modification of a burner design. For research of the phytomass combustion process in the small boilers is constructed the experimental combustion device. There will investigate the impact of cooling intensity of the combustion chamber on the combustion process and emissions. Arising specific requirements from the measurement will be the basis for the design of the pellet burner and for the setting of operating parameters to the trouble-free phytomass combustion was guaranteed.

Global burden of mortalities due to chronic exposure to ambient PM2.5 from open combustion of domestic waste

NASA Astrophysics Data System (ADS)

Kodros, John K.; Wiedinmyer, Christine; Ford, Bonne; Cucinotta, Rachel; Gan, Ryan; Magzamen, Sheryl; Pierce, Jeffrey R.

2016-12-01

Uncontrolled combustion of domestic waste has been observed in many countries, creating concerns for air quality; however, the health implications have not yet been quantified. We incorporate the Wiedinmyer et al (2014 Environ. Sci. Technol. 48 9523-30) emissions inventory into the global chemical-transport model, GEOS-Chem, and provide a first estimate of premature adult mortalities from chronic exposure to ambient PM2.5 from uncontrolled combustion of domestic waste. Using the concentration-response functions (CRFs) of Burnett et al (2014 Environ. Health Perspect. 122 397-403), we estimate that waste-combustion emissions result in 270 000 (5th-95th: 213 000-328 000) premature adult mortalities per year. The confidence interval results only from uncertainty in the CRFs and assumes equal toxicity of waste-combustion PM2.5 to all other PM2.5 sources. We acknowledge that this result is likely sensitive to choice of chemical-transport model, CRFs, and emission inventories. Our central estimate equates to 9% of adult mortalities from exposure to ambient PM2.5 reported in the Global Burden of Disease Study 2010. Exposure to PM2.5 from waste combustion increases the risk of premature mortality by more than 0.5% for greater than 50% of the population. We consider sensitivity simulations to uncertainty in waste-combustion emission mass, the removal of waste-combustion emissions, and model resolution. A factor-of-2 uncertainty in waste-combustion PM2.5 leads to central estimates ranging from 138 000 to 518 000 mortalities per year for factors-of-2 reductions and increases, respectively. Complete removal of waste combustion would only avoid 191 000 (5th-95th: 151 000-224 000) mortalities per year (smaller than the total contributed premature mortalities due to nonlinear CRFs). Decreasing model resolution from 2° × 2.5° to 4° × 5° results in 16% fewer mortalities attributed to waste-combustion PM2.5, and over Asia, decreasing resolution from 0.5° × 0.666° to 2° × 2.5° results in 21% fewer mortalities attributed to waste-combustion PM2.5. Owing to coarse model resolution, our global estimates of premature mortality from waste-combustion PM2.5 are likely a lower bound.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matusik, Katarzyna E.; Duke, Daniel J.; Kastengren, Alan L.

The sparking behavior in an internal combustion engine affects the fuel efficiency, engine-out emissions, and general drivability of a vehicle. As emissions regulations become progressively stringent, combustion strategies, including exhaust gas recirculation (EGR), lean-burn, and turbocharging are receiving increasing attention as models of higher efficiency advanced combustion engines with reduced emissions levels. Because these new strategies affect the working environment of the spark plug, ongoing research strives to understand the influence of external factors on the spark ignition process. Due to the short time and length scales involved and the harsh environment, experimental quantification of the deposited energy from themore » sparking event is difficult to obtain. We present the results of x-ray radiography measurements of spark ignition plasma generated by a conventional spark plug. Our measurements were performed at the 7-BM beamline of the Advanced Photon Source at Argonne National Laboratory. The synchrotron x-ray source enables time-resolved measurements of the density change due to glow discharge in the spark gap with 153 ns temporal and 5 μm spatial resolutions. We also explore the effects of charging time, EGR-relevant gas compositions, and gas pressure on the sparking behavior. We also quantify the influence of the measurement technique on the obtained results.« less

Assessment of emissions of greenhouse gases and air pollutants in Indonesia and impacts of national policy for elimination of kerosene use in cooking

NASA Astrophysics Data System (ADS)

Permadi, Didin Agustian; Sofyan, Asep; Kim Oanh, Nguyen Thi

2017-04-01

This study presents an emission inventory (EI) for major anthropogenic sources of Indonesia in 2007 and 2010. The EI was developed using a combination of top-down and bottom-up approaches with comprehensive activity data collected at the provincial/district level to produce spatially and temporally distributed emission of toxic pollutants and greenhouse gases (GHGs). The sources were categorized into: 1) fuel combustion in power plant, 2) industry, 3) transportation, 4) residential and commercial combustion, 5) biomass open burning, and 6) non-combustion agricultural activity and waste disposal. The best estimates of the 2010 national emissions, in Gg, of toxic pollutants were: 1014 SO2; 3323 NOx; 24,849 CO; 4077 NMVOC; 1276 NH3; 2154 PM10; 1728 PM2.5; 246 BC; 718 OC; and GHGs: 540,275 CO2; 3979 CH4 and 180 N2O. During the period from 2007 to 2010, the national emissions increased by 0.7-8.8% (0.23-2.8% per year), varied with species, with the most significant changes obtained for the biomass open burning emissions. For 2010 results, the low and high emission estimates for different species were ranging from -58% to +122% of the corresponding best estimates. The largest range (high uncertainty) was for BC due to the wide range of the limitedly available emission factors. Spatially, higher emission intensity was seen in large urban areas of Java and Sumatra Islands. Temporally, dry months of August-October had higher emissions. During the first 3 years (2007-2010) of implementation, the national policy of elimination of kerosene use in cooking had successfully replaced 4.9 Tg kerosene with 2.6 Tg LPG in 30 designated provinces. The net emission reductions of different species ranged from 48 Mg (SO2) to 7.6 Tg for CO2. The global warming potential weighted emissions from the residential cooking alone, collectively for GHGs and short-lived climate pollutants in 20-yr CO2 eq., would reduce by 2%. More significant reductions in the residential combustion emissions are expected if the solid cooking fuel could be targeted in future fuel conversion programs. The benefits to human health resulted from the emission reduction of toxic pollutants from residential cooking could be substantial and should be assessed in future studies.

Sorbent control of trace metals in sewage sludge combustion and incineration

NASA Astrophysics Data System (ADS)

Naruse, I.; Yao, H.; Mkilaha, I. S. N.

2003-05-01

Coal and wastes combustion have become an important issue not only in terms of energy generation but also environmental conservation. The need for alternative fuels and wastes management has made the two energy sources of importance. However, the utilization of the two is faced with problems of impurity trace metals in the fuel. These metals usually speciate during combustion or incineration leading to generation of fumes and subsequently particles. This paper reports on the study aimed at understanding the speciation of trace metals and their emission from combustion systems as particulates. Experiments carried out using a down-flow furnace and theoretical study carried out using lead, chromium and cadmium as basic metals had shown that their speciation and subsequent emission is controlled by both chemical composition and physical properties of the fuel. The physical and chemical and physical properties of the fuel and their respective compounds and the operating conditions of the incineration and combustion system control the enrichment of the particles with trace metals.

Practical guide: Tools and methodologies for an oil and gas industry emission inventory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, C.C.; Killian, T.L.

1996-12-31

During the preparation of Title V Permit applications, the quantification and speciation of emission sources from oil and gas facilities were reevaluated to determine the {open_quotes}potential-to-emit.{close_quotes} The existing emissions were primarily based on EPA emission factors such as AP-42, for tanks, combustion sources, and fugitive emissions from component leaks. Emissions from insignificant activities and routine operations that are associated with maintenance, startups and shutdowns, and releases to control devices also required quantification. To reconcile EPA emission factors with test data, process knowledge, and manufacturer`s data, a careful review of other estimation options was performed. This paper represents the results ofmore » this analysis of emission sources at oil and gas facilities, including exploration and production, compressor stations and gas plants.« less

40 CFR 63.923 - Standards-Container Level 2 controls.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES... other requirements for the safe handling of flammable, combustible, explosive, reactive, or hazardous...

Towards the regulation of aerosol emissions by their potential health impact: Assessing adverse effects of aerosols from wood combustion and ship diesel engine emissions by combining comprehensive data on the chemical composition and their toxicological effects on human lung cells

NASA Astrophysics Data System (ADS)

Zimmermann, R.; Streibel, T.; Dittmar, G.; Kanashova, T.; Buters, J.; Öder, S.; Paur, H. R.; Dilger, M.; Weiss, C.; Harndorf, H.; Stengel, B.; Hirvonen, M. R.; Jokiniemi, J.; Hiller, K.; Sapcariu, S.; Sippula, O.; Orasche, J.; Müller, L.; Rheda, A.; Passig, J.; Radischat, C.; Czech, H.; Tiita, P.; Jalava, P.; Kasurinen, S.; Schwemer, T.; Yli-Prilä, P.; Tissari, J.; Lamberg, H.; Schnelle-Kreis, J.

2014-12-01

Ship engine emissions are important regarding lung and cardiovascular diseases in coastal regions worldwide. Bio mass burning is made responsible for adverse health effects in many cities and rural regions. The Virtual Helmholtz Institute-HICE (www.hice-vi.eu) addresses chemical & physical properties and health effects of anthropogenic combustion emissions. Typical lung cell responses to combustion aerosols include inflammation and apoptosis, but a molecular link with the specific chemical composition in particular of ship emissions has not been established. Through an air-liquid interface exposure system (ALI), we exposed human lung cells at-site to exhaust fumes from a ship engine running on common heavy fuel oil (HFO) and cleaner-burning diesel fuel (DF) as well as to emissions of wood combustion compliances. A special field deployable ALI-exposition system and a mobile S2-biological laboratory were developed for this study. Human alveolar basal epithelial cells (A549 etc.) are ALI-exposed to fresh, diluted (1:40-1:100) combustion aerosols and subsequently were toxicologically and molecular-biologically characterized. Advanced chemical analyses of the exhaust aerosols were combined with transcriptional, proteomic and metabolomic profiling to characterise the cellular responses. The HFO ship emissions contained high concentrations of toxic compounds (transition metals, organic toxicants) and particle masses. The cellular responses included inflammation and oxidative stress. Surprisingly, the DF ship emissions, which predominantly contain rather "pure" carbonaceous soot and much less known toxicants, induced significantly broader biological effects, affecting essential cellular pathways (e.g., mitochondrial function and intracellular transport). Therefore the use of distillate fuels for shipping (this is the current emission reduction strategy of the IMO) appears insufficient for diminishing health effects. The study suggests rather reducing the particle emissions by secondary measures (filters) than shifting the fuel. In the case of wood combustion the reduction of soot and carcinogenic aromatic compounds is suggested. However, for both sources (wood and ship diesel) we found that effects of the gaseous pollutants (e.g. aldehydes) are potentially problematic.

Quantifying the sources of atmospheric ice nuclei from carbonaceous combustion aerosol

NASA Astrophysics Data System (ADS)

Schill, G. P.; Jathar, S.; Galang, A.; Farmer, D.; Friedman, B.; Levin, E. J.; DeMott, P. J.; Kreidenweis, S. M.

2015-12-01

Ice nucleation on particles is a fundamental atmospheric process, which governs precipitation, cloud lifetimes, and climate. Despite being a basic atmospheric process, our current understanding of ice nucleation in the atmosphere is low. One reason for this low understanding is that ice nuclei concentrations are low (only ~1 in 105 particles in the free troposphere nucleate ice), making it challenging to identify both the composition and sources of ambient ice nuclei. Carbonaceous combustion aerosol produced from biomass and fossil fuel combustion are one potential source of these ice nuclei, as they contribute to over one-third of all aerosol in the North American free troposphere. Unfortunately, previous results from field measurements in-cloud, aircraft measurements, and laboratory studies are in conflict, with estimates of the impact of combustion aerosol ranging from no effect to rivaling the well-known atmospheric ice nuclei mineral dust. It is, however, becoming clear that aerosols from combustion processes are more complex than model particles, and their ice activity depends greatly on both fuel type and combustion conditions. Given these dependencies, we propose that sampling from real-world biomass burning and fossil fuel sources would provide the most useful new information on the contribution of carbonaceous combustion aerosols to atmospheric ice nuclei particles. To determine the specific contribution of refractory black carbon (rBC) to ice nuclei concentrations, we have coupled the Single Particle Soot Photometer (SP2) to the Colorado State University Continuous Flow Diffusion Chamber (CFDC). The SP2 utilizes laser-induced incandescence to quantify rBC mass on a particle-by-particle basis; in doing so, it also selectively destroys rBC particles by heating them to their vaporization temperature. Thus, the SP2 can be used as a selective pre-filter for rBC into the CFDC. In this work, we will present recent results looking at contribution of diesel engine exhaust to ice nuclei concentrations. Sampling was done for both diesel and biodiesel on fresh emissions and emissions aged up to 18 days equivalent photochemical aging with a Potential Aerosol Mass chamber. Our results show that, for mixed-phase clouds, both fresh and aged (bio)diesel are not likely a significant source of ice nuclei.

Computational Investigation of Combustion Dynamics in a Lean-Direct Injection Gas Turbine Combustor

DTIC Science & Technology

2012-11-01

variable vector which includes turbulence kinetic energy and specific dissipation, k and w; In the viscous flux, D is the molecular diffusion coefficient...for the liquid particle. This equation assumes the uniform temperature inside the liquid particle. The source term consist of the net sensible ...Spray Characteristics on Diesel Engine Combustion and Emission, SAE 980131, 1998 24 Fu, Y., “Aerodynamics and Combustion of Axial Swirlers,” Ph . D. dissertation from the University of Cincinnati, 2008.

Sourcing methane and carbon dioxide emissions from a small city: Influence of natural gas leakage and combustion.

PubMed

Chamberlain, Samuel D; Ingraffea, Anthony R; Sparks, Jed P

2016-11-01

Natural gas leakage and combustion are major sources of methane (CH 4 ) and carbon dioxide (CO 2 ), respectively; however, our understanding of emissions from cities is limited. We mapped distribution pipeline leakage using a mobile CH 4 detection system, and continuously monitored atmospheric CO 2 and CH 4 concentrations and carbon isotopes (δ 13 C-CO 2 and δ 13 C-CH 4 ) for one-year above Ithaca, New York. Pipeline leakage rates were low (<0.39 leaks mile -1 ), likely due to the small extent of cast iron and bare steel within the distribution pipeline system (2.6%). Our atmospheric monitoring demonstrated that the isotopic composition of locally emitted CO 2 approached the δ 13 C range of natural gas combustion in winter, correlating to natural gas power generation patterns at Cornell's Combined Heat and Power Plant located 600 m southeast of the monitoring site. Atmospheric CH 4 plumes were primarily of natural gas origin, were observed intermittently throughout the year, and were most frequent in winter and spring. No correlations between the timing of atmospheric natural gas CH 4 plumes and Cornell Plant gas use patterns could be drawn. However, elevated CH 4 and CO 2 concentrations were observed coincident with high winds from the southeast, and the plant is the only major emission source in that wind sector. Our results demonstrate pipeline leakage rates are low in cities with a low extent of leak prone pipe, and natural gas power facilities may be an important source of urban and suburban emissions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Compilation of Published PM2.5 Emission Rates for Cooking, Candles and Incense for Use in Modeling of Exposures in Residences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Tianchao; Singer, Brett C.; Logue, Jennifer M.

2012-08-01

recent analysis of health impacts from air pollutant inhalation in homes found that PM2.5 is the most damaging at the population level. Chronic exposure to elevated PM2.5 has the potential to damage human respiratory systems, and may result in premature death. PM2.5 exposures in homes can be mitigated through various approaches including kitchen exhaust ventilation, filtration, indoor pollutant source reduction and designing ventilation systems to reduce the entry of PM2.5 from outdoors. Analysis of the potential benefits and costs of various approaches can be accomplished using computer codes that simulate the key physical processes including emissions, dilution and ventilation. Themore » largest sources of PM2.5 in residences broadly are entry from outdoors and emissions from indoor combustion. The largest indoor sources are tobacco combustion (smoking), cooking and the burning of candles and incense. Data on the magnitude of PM2.5 and other pollutant emissions from these events and processes are required to conduct simulations for analysis. The goal of this study was to produce a database of pollutant emission rates associated with cooking and the burning of candles and incense. The target use of these data is for indoor air quality modeling.« less

Controls on boreal peat combustion and resulting emissions of carbon and mercury

NASA Astrophysics Data System (ADS)

Kohlenberg, Andrew J.; Turetsky, Merritt R.; Thompson, Dan K.; Branfireun, Brian A.; Mitchell, Carl P. J.

2018-03-01

Warming in the boreal forest region has already led to changes in the fire regime. This may result in increasing fire frequency or severity in peatlands, which could cause these ecosystems to shift from a net sink of carbon (C) to a net source of C to the atmosphere. Similar to C cycling, peatlands serve as a net sink for mercury (Hg), which binds strongly to organic matter and accumulates in peat over time. This stored Hg is also susceptible to re-release to the atmosphere during peat fires. Here we investigate the physical properties that influence depth of burn in experimental peat columns and the resulting emissions of CO, CO2, CH4, and gaseous and particulate Hg. As expected, bulk density and soil moisture content were important controls on depth of burn, CO2 emissions, and CO emissions. However, our results show that CH4 and Hg emissions are insensitive to combustion temperature or fuel moisture content. Emissions during the burning of peat, across a wide range of moisture conditions, were associated with low particulate Hg and high gaseous Hg release. Due to strong correlations between total Hg and CO emissions and because high Hg emissions occurred despite incomplete combustion of total C, our results suggest that Hg release during peat burning is governed by the thermodynamics of Hg reduction more so than by the release of Hg associated with peat combustion. Our measured emissions ratios, particularly for CH4:CO2, are higher than values typically used in the upscaling of boreal forest or peatland fire emissions. These emission ratios have important implications not only for our understanding of smouldering chemistry, but also for potential influences of peat fires on the Earth’s climate system.

Mapping 1995 global anthropogenic emissions of mercury

NASA Astrophysics Data System (ADS)

Pacyna, Jozef M.; Pacyna, Elisabeth G.; Steenhuisen, Frits; Wilson, Simon

This paper presents maps of anthropogenic Hg emissions worldwide within a 1°×1° latitude/longitude grid system in 1995. As such, the paper is designed for modelers simulating the Hg transport within air masses and Hg deposition to aquatic and terrestrial ecosystems. Maps of total Hg emissions and its three main chemical species: elemental gaseous Hg, divalent gaseous Hg, and particle-associated Hg are presented. The main emissions occur in southeast Asia (particularly in China), South Africa, Central and Eastern Europe, and the Eastern United States. These are the regions where coal combustion is the main source of electricity and heat production. Waste incineration adds to these emissions in the Eastern United States. Emissions of total Hg and its three species are quite similar in terms of their (global) spatial distributions. They reflect the worldwide distribution of coal consumption in large power plants, industrial burners, and small combustion units, such as residential and commercial furnaces.

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...) Additional reporting requirements for HAP metals standards. (1) Any owner or operator of a group of process units in a chemical recovery system at a mill complying with the PM emissions limits in § 63.862(a)(1...

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...) Additional reporting requirements for HAP metals standards. (1) Any owner or operator of a group of process units in a chemical recovery system at a mill complying with the PM emissions limits in § 63.862(a)(1...

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...) Additional reporting requirements for HAP metals standards. (1) Any owner or operator of a group of process units in a chemical recovery system at a mill complying with the PM emissions limits in § 63.862(a)(1...

40 CFR 98.210 - Definition of the source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... considered to emit CO2 if they consume at least 2,000 tons per year of carbonates heated to a temperature... that uses carbonates or carbonate containing minerals that are consumed in the production of cement... technology used to control emissions from stationary fuel combustion equipment. Emissions from carbonates...

40 CFR 98.210 - Definition of the source category.

Code of Federal Regulations, 2014 CFR

2014-07-01

... considered to emit CO2 if they consume at least 2,000 tons per year of carbonates heated to a temperature... that uses carbonates or carbonate containing minerals that are consumed in the production of cement... technology used to control emissions from stationary fuel combustion equipment. Emissions from carbonates...

40 CFR 98.152 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GREENHOUSE GAS REPORTING HCFC-22 Production and HFC-23 Destruction § 98.152 GHGs to report. (a) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2... must report HFC-23 emissions from HCFC-22 production processes and HFC-23 destruction processes. ...

40 CFR 98.152 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GREENHOUSE GAS REPORTING HCFC-22 Production and HFC-23 Destruction § 98.152 GHGs to report. (a) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2... must report HFC-23 emissions from HCFC-22 production processes and HFC-23 destruction processes. ...

40 CFR 98.210 - Definition of the source category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... considered to emit CO2 if they consume at least 2,000 tons per year of carbonates heated to a temperature... that uses carbonates or carbonate containing minerals that are consumed in the production of cement... technology used to control emissions from stationary fuel combustion equipment. Emissions from carbonates...

40 CFR 98.210 - Definition of the source category.

Code of Federal Regulations, 2012 CFR

2012-07-01

... considered to emit CO2 if they consume at least 2,000 tons per year of carbonates heated to a temperature... that uses carbonates or carbonate containing minerals that are consumed in the production of cement... technology used to control emissions from stationary fuel combustion equipment. Emissions from carbonates...

40 CFR 98.152 - GHGs to report.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GREENHOUSE GAS REPORTING HCFC-22 Production and HFC-23 Destruction § 98.152 GHGs to report. (a) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2... must report HFC-23 emissions from HCFC-22 production processes and HFC-23 destruction processes. ...

40 CFR 98.152 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GREENHOUSE GAS REPORTING HCFC-22 Production and HFC-23 Destruction § 98.152 GHGs to report. (a) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2... must report HFC-23 emissions from HCFC-22 production processes and HFC-23 destruction processes. ...

40 CFR 98.152 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GREENHOUSE GAS REPORTING HCFC-22 Production and HFC-23 Destruction § 98.152 GHGs to report. (a) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2... must report HFC-23 emissions from HCFC-22 production processes and HFC-23 destruction processes. ...

Open burning of household waste: Effect of experimental condition on combustion quality and emission of PCDD, PCDF and PCB

EPA Science Inventory

Open burning for waste disposal is, in many countries, the dominant source of polychlorinated dibenzodioxins/dibenzofurans and polychlorinated biphenyls (PCDD/PCDF/PCB) release to the environment. To generate emission factors for open burning, experimental pile burns of ca 100 k...

Unspeciated organic emissions from combustion sources and their influence on the secondary organic aerosol budget in the United States

EPA Science Inventory

Secondary organic aerosol (SOA) formed from the atmospheric oxidation of nonmethane organic gases (NMOG) is a major contributor to atmospheric aerosol mass. Emissions and smog chamber experiments were performed to investigate SOA formation from gasoline vehicles, diesel vehicles,...

A paler shade of green? The toxicology of biodiesel emissions: recent findings from studies with this alternative fuel

EPA Science Inventory

Background: Biodiesel produced primarily from plants and algal feedstocks is believed to have advantages for production and use compared to petroleum and to some other fuel sources. There is some speculation that exposure to biodiesel combustion emissions may not induce biologic...

40 CFR 63.6150 - What reports must I submit and when?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines Notifications, Reports, and... 40 Protection of Environment 12 2011-07-01 2009-07-01 true What reports must I submit and when? 63...

40 CFR 63.6150 - What reports must I submit and when?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines Notifications, Reports, and... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What reports must I submit and when? 63...

ANALYSIS OF LEAD IN CANDLE PARTICULATE EMISSIONS BY XRF USING UNIQUANT 4

EPA Science Inventory

As part of an extensive program to study the small combustion sources of indoor fine particulate matter (PM), candles with lead-core wicks were burned in a 46-L glass flow- through chamber. The particulate emissions with aerodynamic diameters <10 micrometers (PM10) were captured ...

Smoke and fire characteristics for cerrado and deforestation burns in Brazil: BASE-B experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, D.E.; Susott, R.A.; Babbitt, R.E.

1992-09-20

Fires of the tropical forests and savannas are a major source of particulate matter and trace gases affecting the atmosphere globally. A paucity of quantitative information exists for these ecosystems with respect to fuel biomass, smoke emissions, and fire behavior conditions affecting the release of emissions. Five test fires were performed during August and September 1990 in the cerrado (savannalike region) in central Brazil (three fires) and tropical moist forest (two fires) in the eastern Amazon. This paper details the gases released, the ratios of the gases to each other and to particulate matter, fuel loads and the fraction consumedmore » (combustion factors), and the fire behavior associated with biomass consumption. Models are presented for evaluating emission factors for CH{sub 4}, CO{sub 2}, CO, H{sub 2}, and particles less than 2.5 {mu}m diameter (PM2.5) as a function of combustion efficiency. The ratio of carbon released as CO{sub 2} (combustion efficiency) for the cerrado fires averaged 0.94 and for the deforestation fires it decreased from 0.88 for the flaming phase to <0.80 during the smoldering phase of combustion. For tropical ecosystems, emissions of most products of incomplete combustion are projected to be lower than previous estimates for savanna ecosystems and somewhat higher for fires used for deforestation purposes. 59 refs., 9 figs., 10 tabs.« less

40 CFR 74.25 - Current promulgated SO2 emissions limit.

Code of Federal Regulations, 2011 CFR

2011-07-01

... promulgated SO2 emissions limit of the combustion source, expressed in lbs/mmBtu, which shall be the most... date. If the promulgated SO2 emissions limit is not expressed in lbs/mmBtu, the limit shall be converted to lbs/mmBtu by multiplying the limit by the appropriate factor as specified in Table 1 of § 74.23...

Polycyclic aromatic hydrocarbons in the urban atmosphere of Nepal: Distribution, sources, seasonal trends, and cancer risk.

PubMed

Pokhrel, Balram; Gong, Ping; Wang, Xiaoping; Wang, Chuanfei; Gao, Shaoping

2018-03-15

Atmospheric polycyclic aromatic hydrocarbons (PAHs) in urban areas have always been a global concern, as these areas are considered to be the source region. Despite studies on the concentrations of PAHs in water, soils and sediments, knowledge of the distribution patterns, seasonality and sources of PAHs in urban areas of Nepal remains limited. In this study, polyurethane foam passive air samplers were used to measure gas-phase PAH concentrations over different land types in three major cities of Nepal-namely, Kathmandu (the capital) and Pokhara (both densely populated cities), and Hetauda (an agricultural city). The average concentrations of ∑15PAHs in ng/m 3 were 16.1±7.0 (6.4-28.6), 14.1±6.2 (6.8-29.4) and 11.1±9.0 (4.1-38.0) in Kathmandu, Pokhara and Hetauda, respectively. Molecular diagnostic ratio analysis suggested that fossil fuel combustion was a common PAH source for all three cities. In addition to this, coal combustion in Kathmandu, vehicle emissions in Pokhara, and grass/wood combustion in Hetauda were also possible sources of PAHs. In terms of cancer risk from PAH inhalation, a religious site with intense incense burning, a brick production area where extensive coal combustion is common, and a market place with heavy traffic emission, were associated with a higher risk than other areas. There were no clear seasonal trends in atmospheric PAHs. The estimated cancer risk due to inhalation of gas-phase PAHs exceeded the USEPA standard at >90% of the sites. Copyright © 2017 Elsevier B.V. All rights reserved.

Characterization of Arctic elemental carbon in Barrow, AK using radiocarbon source apportionment

NASA Astrophysics Data System (ADS)

Barrett, T. E.; Usenko, S.; Robinson, E. M.; Sheesley, R. J.

2013-12-01

Currently, the Arctic is one of the fastest warming regions on earth with surface temperatures increasing at a rate nearly double the global mean over recent decades. Despite the fact that atmospheric concentrations of elemental carbon (EC) are lower in the Arctic than in lower latitudes, deposition of EC on snow and ice may exacerbate regional warming by simultaneously decreasing albedo and increasing melt rates. Due to the intensifying Arctic oil exploration in areas such as the Beaufort and Chukchi seas, the impact of new emission sources such as heavy fuel and heavy diesel combustion on regional carbon needs to be assessed. The first step in developing mitigation strategies for reducing current and future EC emissions in the Arctic is to determine emission source contributions. This study aims to determine the relative contributions of fossil fuel and biomass combustion and to identify major source regions of EC to the Arctic. Radiocarbon analysis of both total organic carbon (TOC) and EC combined with organic tracer and back trajectory analysis has been applied to a set of wintertime coarse particulate matter (PM10) samples from Barrow, AK. Preliminary apportionment for January 2013 indicates roughly half of TOC is from biogenic/biomass burning emissions and one third of EC is due to biomass burning emissions. The radiocarbon results will be combined with organic tracer analysis (polycyclic aromatic hydrocarbons, petroleum biomarkers and normal alkanes), increasing the specificity of the relative contribution of both the fossil and modern (biogenic/biomass burning) carbon emission sources. This research represents the first reported radiocarbon values for Arctic EC, providing highly conclusive source apportionment prior to the influence of increased drilling operations and ship traffic in the Beaufort and Chukchi seas.

Important fossil source contribution to brown carbon in Beijing during winter

NASA Astrophysics Data System (ADS)

Yan, Caiqing; Zheng, Mei; Bosch, Carme; Andersson, August; Desyaterik, Yury; Sullivan, Amy P.; Collett, Jeffrey L.; Zhao, Bin; Wang, Shuxiao; He, Kebin; Gustafsson, Örjan

2017-03-01

Organic aerosol (OA) constitutes a substantial fraction of fine particles and affects both human health and climate. It is becoming clear that OA absorbs light substantially (hence termed Brown Carbon, BrC), adding uncertainties to global aerosol radiative forcing estimations. The few current radiative-transfer and chemical-transport models that include BrC primarily consider sources from biogenic and biomass combustion. However, radiocarbon fingerprinting here clearly indicates that light-absorbing organic carbon in winter Beijing, the capital of China, is mainly due to fossil sources, which contribute the largest part to organic carbon (OC, 67 ± 3%) and its sub-constituents (water-soluble OC, WSOC: 54 ± 4%, and water-insoluble OC, WIOC: 73 ± 3%). The dual-isotope (Δ14C/δ13C) signatures, organic molecular tracers and Beijing-tailored emission inventory identify that this fossil source is primarily from coal combustion activities in winter, especially from the residential sector. Source testing on Chinese residential coal combustion provides direct evidence that intensive coal combustion could contribute to increased light-absorptivity of ambient BrC in Beijing winter. Coal combustion is an important source to BrC in regions such as northern China, especially during the winter season. Future modeling of OA radiative forcing should consider the importance of both biomass and fossil sources.

Important fossil source contribution to brown carbon in Beijing during winter

PubMed Central

Yan, Caiqing; Zheng, Mei; Bosch, Carme; Andersson, August; Desyaterik, Yury; Sullivan, Amy P.; Collett, Jeffrey L.; Zhao, Bin; Wang, Shuxiao; He, Kebin; Gustafsson, Örjan

2017-01-01

Organic aerosol (OA) constitutes a substantial fraction of fine particles and affects both human health and climate. It is becoming clear that OA absorbs light substantially (hence termed Brown Carbon, BrC), adding uncertainties to global aerosol radiative forcing estimations. The few current radiative-transfer and chemical-transport models that include BrC primarily consider sources from biogenic and biomass combustion. However, radiocarbon fingerprinting here clearly indicates that light-absorbing organic carbon in winter Beijing, the capital of China, is mainly due to fossil sources, which contribute the largest part to organic carbon (OC, 67 ± 3%) and its sub-constituents (water-soluble OC, WSOC: 54 ± 4%, and water-insoluble OC, WIOC: 73 ± 3%). The dual-isotope (Δ14C/δ13C) signatures, organic molecular tracers and Beijing-tailored emission inventory identify that this fossil source is primarily from coal combustion activities in winter, especially from the residential sector. Source testing on Chinese residential coal combustion provides direct evidence that intensive coal combustion could contribute to increased light-absorptivity of ambient BrC in Beijing winter. Coal combustion is an important source to BrC in regions such as northern China, especially during the winter season. Future modeling of OA radiative forcing should consider the importance of both biomass and fossil sources. PMID:28266611

Temporal evolution of ultrafine particles and of alveolar deposited surface area from main indoor combustion and non-combustion sources in a model room.

PubMed

Manigrasso, Maurizio; Vitali, Matteo; Protano, Carmela; Avino, Pasquale

2017-11-15

Aerosol number size distributions, PM mass concentrations, alveolar deposited surface areas (ADSAs) and VOC concentrations were measured in a model room when aerosol was emitted by sources frequently encountered in indoor environments. Both combustion and non-combustion sources were considered. The most intense aerosol emission occurred when combustion sources were active (as high as 4.1×10 7 particlescm -3 for two meat grilling sessions; the first with exhaust ventilation, the second without). An intense spike generation of nucleation particles occurred when appliances equipped with brush electric motors were operating (as high as 10 6 particlescm -3 on switching on an electric drill). Average UFP increments over the background value were highest for electric appliances (5-12%) and lowest for combustion sources (as low as -24% for tobacco cigarette smoke). In contrast, average increments in ADSA were highest for combustion sources (as high as 3.2×10 3 μm 2 cm -3 for meat grilling without exhaust ventilation) and lowest for electric appliances (20-90μm 2 cm -3 ). The health relevance of such particles is associated to their ability to penetrate cellular structures and elicit inflammatory effects mediated through oxidative stress in a way dependent on their surface area. The highest VOC concentrations were measured (PID probe) for cigarette smoke (8ppm) and spray air freshener (10ppm). The highest PM mass concentration (PM 1 ) was measured for citronella candle burning (as high as 7.6mgm -3 ). Copyright © 2017 Elsevier B.V. All rights reserved.

RADIOCARBON SOURCE APPORTIONMENT IN A BIOFUELS ERA

EPA Science Inventory

Biofuels (gasohol and biodiesel) introduce radiocarbon into the U.S. mobile source fuel supply where it was previously absent. Initial measurements of radiocarbon in the PM_2.5 combustion emissions from engines using gasohol indicate that this may have less effect on r...

Anomalous elevated radiocarbon measurements of PM2.5

NASA Astrophysics Data System (ADS)

Buchholz, Bruce A.; Fallon, Stewart J.; Zermeño, Paula; Bench, Graham; Schichtel, Bret A.

2013-01-01

Two-component models are often used to determine the contributions made by fossil fuel and natural sources of carbon in airborne particulate matter (PM). The models reduce thousands of actual sources to two end members based on isotopic signature. Combustion of fossil fuels produces PM free of carbon-14 (14C). Wood or charcoal smoke, restaurant fryer emissions, and natural emissions from plants produce PM with the contemporary concentration of 14C approximately 1.2 × 10-1214C/C. Such data can be used to estimate the relative contributions of fossil fuels and biogenic aerosols to the total aerosol loading and radiocarbon analysis is becoming a popular source apportionment method. Emissions from incinerators combusting medical or biological wastes containing tracer 14C can skew the 14C/C ratio of PM, however, so critical analysis of sampling sites for possible sources of elevated PM needs to be completed prior to embarking on sampling campaigns. Results are presented for two ambient monitoring sites in different areas of the United States where 14C contamination is apparent. Our experience suggests that such contamination is uncommon but is also not rare (∼10%) for PM sampling sites.

PM2.5 emissions and source profiles from open burning of crop residues

NASA Astrophysics Data System (ADS)

Ni, Haiyan; Tian, Jie; Wang, Xiaoliang; Wang, Qiyuan; Han, Yongming; Cao, Junji; Long, Xin; Chen, L.-W. Antony; Chow, Judith C.; Watson, John G.; Huang, Ru-Jin; Dusek, Ulrike

2017-11-01

Wheat straw, rice straw, and corn stalks, the major agricultural crop residues in China, were collected from six major crop producing regions, and burned in a laboratory combustion chamber to determine PM2.5 source profiles and speciated emission factors (EFs). Organic carbon (OC) and water-soluble ions (the sum of NH4+, Na+, K+, Mg2+, Ca2+, Cl-, NO3- and SO42-) are major constituents, accounting for 43.1 ± 8.3% and 27.4 ± 14.6% of PM2.5, respectively. Chloride (Cl-) and water-soluble potassium (K+) are the dominant ionic species, with an average abundance of 14.5 ± 8.2% and 6.4 ± 4.4% in PM2.5, respectively. The average K+/Cl- ratio is ∼0.4, lower than 2.8-5.4 for wood combustion. Similarity measures (i.e., Student's t-test, coefficient of divergence, correlations, and residual to uncertainty ratios) show the crop profiles are too similar for the species measured to be resolved from one another by receptor modeling. The largest difference was found between rice straw and corn stalk emissions, with higher OC and lower Cl- and K+ abundances (50%, 8%, and 3% of PM2.5, respectively) for corn stalks; lower OC, and higher Cl- and K+ abundances (38%, 21%, and 10% of PM2.5, respectively) for rice straw. Average EFs were 4.8 ± 3.1 g kg-1 for OC, 1.3 ± 0.8 g kg-1 for Cl- and 0.59 ± 0.56 g kg-1 for K+. Flaming and smoldering combustions resulted in an average modified combustion efficiency (MCE) of 0.92 ± 0.03, and low elemental carbon (EC) EFs (0.24 ± 0.12 g kg-1). OC/EC ratios from individual source profiles ranged from 12.9 ± 4.3 for rice straw to 24.1 ± 13.5 for wheat straw. The average K+/EC ratio was 2.4 ± 1.5, an order of magnitude higher than those from residential wood combustion (0.2-0.76). Elevated emission rates were found for OC (387 Gg yr-1) and Cl- (122 Gg yr-1), accounting for 44% and 14% of 2008 PM2.5 emissions in China.

Anthropogenic atmospheric emissions of cadmium in China

NASA Astrophysics Data System (ADS)

Shao, Xiao; Cheng, Hongguang; Li, Qian; Lin, Chunye

2013-11-01

In this study, we estimated atmospheric Cd emissions from anthropogenic sources in China from 1990 to 2010 on the basis of consumption or output data and emission factors. China emitted approximately 2186 t Cd to the atmosphere in 2010, with approximately 77% and 14% of the emissions arising from non-ferrous metal smelting and coal combustion, respectively. Temporal changes in the total Cd emissions were characterized by two periods of increase (1990-2000 and 2001-2010) and a short period of decrease (2000-2001) due to application of energy-saving and cleaner production technologies. Overall, atmospheric Cd emissions increased from 474 t in 1990 to 2186 t in 2010 due to rapid economic growth, whereas energy-saving and cleaner production technologies have been in use since 2000. Spatial distribution of the atmospheric Cd emissions was dominated primarily by non-ferrous metal smelting and coal combustion. Emissions are high in Hunan and Yunnan Provinces because of high production non-ferrous metal smelting and in Shandong Province because of high coal consumption and moderate non-ferrous metal production.

Cross-scale controls on carbon emissions from boreal forest megafires.

PubMed

Walker, Xanthe J; Rogers, Brendan M; Baltzer, Jennifer L; Cumming, Steven G; Day, Nicola J; Goetz, Scott J; Johnstone, Jill F; Schuur, Edward A G; Turetsky, Merritt R; Mack, Michelle C

2018-04-26

Climate warming and drying is associated with increased wildfire disturbance and the emergence of megafires in North American boreal forests. Changes to the fire regime are expected to strongly increase combustion emissions of carbon (C) which could alter regional C balance and positively feedback to climate warming. In order to accurately estimate C emissions and thereby better predict future climate feedbacks, there is a need to understand the major sources of heterogeneity that impact C emissions at different scales. Here, we examined 211 field plots in boreal forests dominated by black spruce (Picea mariana) or jack pine (Pinus banksiana) of the Northwest Territories (NWT), Canada after an unprecedentedly large area burned in 2014. We assessed both aboveground and soil organic layer (SOL) combustion, with the goal of determining the major drivers in total C emissions, as well as to develop a high spatial resolution model to scale emissions in a relatively understudied region of the boreal forest. On average, 3.35 kg C m -2 was combusted and almost 90% of this was from SOL combustion. Our results indicate that black spruce stands located at landscape positions with intermediate drainage contribute the most to C emissions. Indices associated with fire weather and date of burn did not impact emissions, which we attribute to the extreme fire weather over a short period of time. Using these results, we estimated a total of 94.3 Tg C emitted from 2.85 Mha of burned area across the entire 2014 NWT fire complex, which offsets almost 50% of mean annual net ecosystem production in terrestrial ecosystems of Canada. Our study also highlights the need for fine-scale estimates of burned area that represent small water bodies and regionally specific calibrations of combustion that account for spatial heterogeneity in order to accurately model emissions at the continental scale. © 2018 John Wiley & Sons Ltd.

Dispersion modeling of polycyclic aromatic hydrocarbons from combustion of biomass and fossil fuels and production of coke in Tianjin, China.

PubMed

Tao, Shu; Li, Xinrong; Yang, Yu; Coveney, Raymond M; Lu, Xiaoxia; Chen, Haitao; Shen, Weiran

2006-08-01

A USEPA, procedure, ISCLT3 (Industrial Source Complex Long-Term), was applied to model the spatial distribution of polycyclic aromatic hydrocarbons (PAHs) emitted from various sources including coal, petroleum, natural gas, and biomass into the atmosphere of Tianjin, China. Benzo[a]pyrene equivalent concentrations (BaPeq) were calculated for risk assessment. Model results were provisionally validated for concentrations and profiles based on the observed data at two monitoring stations. The dominant emission sources in the area were domestic coal combustion, coke production, and biomass burning. Mainly because of the difference in the emission heights, the contributions of various sources to the average concentrations at receptors differ from proportions emitted. The shares of domestic coal increased from approximately 43% at the sources to 56% at the receptors, while the contributions of coking industry decreased from approximately 23% at the sources to 7% at the receptors. The spatial distributions of gaseous and particulate PAHs were similar, with higher concentrations occurring within urban districts because of domestic coal combustion. With relatively smaller contributions, the other minor sources had limited influences on the overall spatial distribution. The calculated average BaPeq value in air was 2.54 +/- 2.87 ng/m3 on an annual basis. Although only 2.3% of the area in Tianjin exceeded the national standard of 10 ng/m3, 41% of the entire population lives within this area.

Particulate matter chemical component concentrations and sources in settings of household solid fuel use.

PubMed

Secrest, M H; Schauer, J J; Carter, E M; Baumgartner, J

2017-11-01

Particulate matter (PM) air pollution derives from combustion and non-combustion sources and consists of various chemical species that may differentially impact human health and climate. Previous reviews of PM chemical component concentrations and sources focus on high-income urban settings, which likely differ from the low- and middle-income settings where solid fuel (ie, coal, biomass) is commonly burned for cooking and heating. We aimed to summarize the concentrations of PM chemical components and their contributing sources in settings where solid fuel is burned. We searched the literature for studies that reported PM component concentrations from homes, personal exposures, and direct stove emissions under uncontrolled, real-world conditions. We calculated weighted mean daily concentrations for select PM components and compared sources of PM determined by source apportionment. Our search criteria yielded 48 studies conducted in 12 countries. Weighted mean daily cooking area concentrations of elemental carbon, organic carbon, and benzo(a)pyrene were 18.8 μg m -3 , 74.0 μg m -3 , and 155 ng m -3 , respectively. Solid fuel combustion explained 29%-48% of principal component/factor analysis variance and 41%-87% of PM mass determined by positive matrix factorization. Multiple indoor and outdoor sources impacted PM concentrations and composition in these settings, including solid fuel burning, mobile emissions, dust, and solid waste burning. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Oxygenated fraction and mass of organic aerosol from direct emission and atmospheric processing measured on the R/V Ronald Brown during TEXAQS/GoMACCS 2006

NASA Astrophysics Data System (ADS)

Russell, L. M.; Takahama, S.; Liu, S.; Hawkins, L. N.; Covert, D. S.; Quinn, P. K.; Bates, T. S.

2009-04-01

Submicron particles collected on Teflon filters aboard the R/V Ronald Brown during the Texas Air Quality Study and Gulf of Mexico Atmospheric Composition and Climate Study (TexAQS/GoMACCS) 2006 in and around the port of Houston, Texas, were measured by Fourier transform infrared (FTIR) and X-ray fluorescence for organic functional groups and elemental composition. Organic mass (OM) concentrations (1-25 μg m-3) for ambient particle samples measured by FTIR showed good agreement with measurements made with an aerosol mass spectrometer. The fractions of organic mass identified as alkane and carboxylic acid groups were 47% and 32%, respectively. Three different types of air masses were identified on the basis of the air mass origin and the radon concentration, with significantly higher carboxylic acid group mass fractions in air masses from the north (35%) than the south (29%) or Gulf of Mexico (26%). Positive matrix factorization analysis attributed carboxylic acid fractions of 30-35% to factors with mild or strong correlations (r > 0.5) to elemental signatures of oil combustion and 9-24% to wood smoke, indicating that part of the carboxylic acid fraction of OM was formed by the same sources that controlled the metal emissions, namely the oil and wood combustion activities. The implication is that a substantial part of the measured carboxylic acid contribution was formed independently of traditionally "secondary" processes, which would be affected by atmospheric (both photochemical and meteorological) conditions and other emission sources. The carboxylic acid group fractions in the Gulf of Mexico and south air masses (GAM and SAM, respectively) were largely oil combustion emissions from ships as well as background marine sources, with only limited recent land influences (based on radon concentrations). Alcohol groups accounted for 14% of OM (mostly associated with oil combustion emissions and background sources), and amine groups accounted for 4% of OM in all air masses. Organosulfate groups were found in GAM and SAM, accounting for 1% and 3% of OM, respectively. Two thirds of the OM and oxygen-to-carbon (O/C) measured could be attributed to oil and wood combustion sources on the basis of mild or strong correlations to coemitted, nonvolatile trace metals, with the remaining one third being associated with atmospherically processed organic aerosol. The cloud condensation nuclei (CCN) fraction (normalized by total condensation nuclei) had weak correlations to the alcohol and amine group fractions and mild correlation with O/C, also varying inversely with alkane group fraction. The chemical components that influenced f(RH) were sulfate, organic, and nitrate fraction, but this contrast is consistent with the size-distribution dependence of CCN counters and nephelometers.

Positive matrix factorization and trajectory modelling for source identification: A new look at Indian Ocean Experiment ship observations

NASA Astrophysics Data System (ADS)

Bhanuprasad, S. G.; Venkataraman, Chandra; Bhushan, Mani

The sources of aerosols on a regional scale over India have only recently received attention in studies using back trajectory analysis and chemical transport modelling. Receptor modelling approaches such as positive matrix factorization (PMF) and the potential source contribution function (PSCF) are effective tools in source identification of urban and regional-scale pollution. In this work, PMF and PSCF analysis is applied to identify categories and locations of sources that influenced surface concentrations of aerosols in the Indian Ocean Experiment (INDOEX) domain measured on-board the research vessel Ron Brown [Quinn, P.K., Coffman, D.J., Bates, T.S., Miller, T.L., Johnson, J.E., Welton, E.J., et al., 2002. Aerosol optical properties during INDOEX 1999: means, variability, and controlling factors. Journal of Geophysical Research 107, 8020, doi:10.1029/2000JD000037]. Emissions inventory information is used to identify sources co-located with probable source regions from PSCF. PMF analysis identified six factors influencing PM concentrations during the INDOEX cruise of the Ron Brown including a biomass combustion factor (35-40%), three industrial emissions factors (35-40%), primarily secondary sulphate-nitrate, balance trace elements and Zn, and two dust factors (20-30%) of Si- and Ca-dust. The identified factors effectively predict the measured submicron PM concentrations (slope of regression line=0.90±0.20; R2=0.76). Probable source regions shifted based on changes in surface and elevated flows during different times in the ship cruise. They were in India in the early part of the cruise, but in west Asia, south-east Asia and Africa, during later parts of the cruise. Co-located sources include coal-fired electric utilities, cement, metals and petroleum production in India and west Asia, biofuel combustion for energy and crop residue burning in India, woodland/forest burning in north sub-Saharan Africa and forest burning in south-east Asia. Significant findings are equivalent contributions of biomass combustion and industrial emissions to the measured aerosol surface concentrations, the origin of carbonaceous aerosols largely from biomass combustion and the identification of probable source regions in Africa, west Asia, the Arabian peninsula and south-east Asia, in addition to India, which affected particulate matter concentrations over parts of the INDOEX domain covered by the Ron Brown cruise.

Source apportionment of fine particles and its chemical components over the Yangtze River Delta, China during a heavy haze pollution episode

NASA Astrophysics Data System (ADS)

Li, L.; An, J. Y.; Zhou, M.; Yan, R. S.; Huang, C.; Lu, Q.; Lin, L.; Wang, Y. J.; Tao, S. K.; Qiao, L. P.; Zhu, S. H.; Chen, C. H.

2015-12-01

An extremely high PM2.5 pollution episode occurred over the eastern China in January 2013. In this paper, the particulate matter source apportionment technology (PSAT) method coupled within the Comprehensive air quality model with extensions (CAMx) is applied to study the source contributions to PM2.5 and its major components at six receptors (Urban Shanghai, Chongming, Dianshan Lake, Urban Suzhou, Hangzhou and Zhoushan) in the Yangtze River Delta (YRD) region. Contributions from 4 source areas (including Shanghai, South Jiangsu, North Zhejiang and Super-region) and 9 emission sectors (including power plants, industrial boilers and kilns, industrial processing, mobile source, residential, volatile emissions, dust, agriculture and biogenic emissions) to PM2.5 and its major components (sulfate, nitrate, ammonia, organic carbon and elemental carbon) at the six receptors in the YRD region are quantified. Results show that accumulation of local pollution was the largest contributor during this air pollution episode in urban Shanghai (55%) and Suzhou (46%), followed by long-range transport (37% contribution to Shanghai and 44% to Suzhou). Super-regional emissions play an important role in PM2.5 formation at Hangzhou (48%) and Zhoushan site (68%). Among the emission sectors contributing to the high pollution episode, the major source categories include industrial processing (with contributions ranging between 12.7 and 38.7% at different receptors), combustion source (21.7-37.3%), mobile source (7.5-17.7%) and fugitive dust (8.4-27.3%). Agricultural contribution is also very significant at Zhoushan site (24.5%). In terms of the PM2.5 major components, it is found that industrial boilers and kilns are the major source contributor to sulfate and nitrate. Volatile emission source and agriculture are the major contributors to ammonia; transport is the largest contributor to elemental carbon. Industrial processing, volatile emissions and mobile source are the most significant contributors to organic carbon. Results show that the Yangtze River Delta region should focus on the joint pollution control of industrial processing, combustion emissions, mobile source emissions, and fugitive dust. Regional transport of air pollution among the cities are prominent, and the implementation of regional joint prevention and control of air pollution will help to alleviate fine particulate matter concentrations under heavy pollution case significantly.

A spatially resolved fuel-based inventory of Utah and Colorado oil and natural gas emissions

NASA Astrophysics Data System (ADS)

Gorchov Negron, A.; McDonald, B. C.; De Gouw, J. A.; Frost, G. J.

2015-12-01

A fuel-based approach is presented for estimating emissions from US oil and natural gas production that utilizes state-level fuel surveys of oil and gas engine activity, well-level production data, and emission factors for oil and gas equipment. Emissions of carbon dioxide (CO2) and nitrogen oxides (NOx) are mapped on a 4 km x 4 km horizontal grid for 2013-14 in Utah and Colorado. Emission sources include combustion from exploration (e.g., drilling), production (e.g., heaters, dehydrators, and compressor engines), and natural gas processing plants, which comprise a large fraction of the local combustion activity in oil and gas basins. Fuel-based emission factors of NOx are from the U.S. Environmental Protection Agency, and applied to spatially-resolved maps of CO2 emissions. Preliminary NOx emissions from this study are estimated for the Uintah Basin, Utah, to be ~5300 metric tons of NO2-equivalent in 2013. Our result compares well with an observations-based top-down emissions estimate of NOx derived from a previous study, ~4200 metric tons of NO2-equivalent. By contrast, the 2011 National Emissions Inventory estimates oil and gas emissions of NOx to be ~3 times higher than our study in the Uintah Basin. We intend to expand our fuel-based approach to map combustion-related emissions in other U.S. oil and natural gas basins and compare with additional observational datasets.

PAH molecular diagnostic ratios applied to atmospheric sources: a critical evaluation using two decades of source inventory and air concentration data from the UK.

PubMed

Katsoyiannis, Athanasios; Sweetman, Andrew J; Jones, Kevin C

2011-10-15

Molecular diagnostic ratios (MDRs)-the ratios of defined pairs of individual compounds-have been widely used as markers of different source categories of polycyclic aromatic hydrocarbons (PAHs). However, it is well-known that variations in combustion conditions and environmental degradation processes can cause substantial variability in the emission and degradation of individual compounds, potentially undermining the application of MDRs as reliable source apportionment tools. The United Kingdom produces a national inventory of atmospheric emissions of PAHs, and has an ambient air monitoring program at a range of rural, semirural, urban, and industrial sites. The inventory and the monitoring data are available over the past 20 years (1990-2010), a time frame that has seen known changes in combustion type and source. Here we assess 5 MDRs that have been used in the literature as source markers. We examine the spatial and temporal variability in the ratios and consider whether they are responsive to known differences in source strength and types between sites (on rural-urban gradients) and to underlying changes in national emissions since 1990. We conclude that the use of these 5 MDRs produces contradictory results and that they do not respond to known differences (in time and space) in atmospheric emission sources. For example, at a site near a motorway and far from other evident emission sources, the use of MDRs suggests "non-traffic" emissions. The ANT/(ANT + PHE) ratio is strongly seasonal at some sites; it is the most susceptible MDR to atmospheric processes, so these results illustrate how weathering in the environment will undermine the effectiveness of MDRs as markers of source(s). We conclude that PAH MDRs can exhibit spatial and temporal differences, but they are not valid markers of known differences in source categories and type. Atmospheric sources of PAHs in the UK are probably not dominated by any single clear and strong source type, so the mixture of PAHs in air is quickly "blended" away from the influence of the few major point sources which exist and further weathered in the environment by atmospheric reactions and selective loss processes.

Health Impact of PM10, PM2.5 and Black Carbon Exposure Due to Different Source Sectors in Stockholm, Gothenburg and Umea, Sweden

PubMed Central

Eneroth, Kristina; Gidhagen, Lars; Johansson, Christer; Omstedt, Gunnar; Engström Nylén, Anders; Forsberg, Bertil

2017-01-01

The most important anthropogenic sources of primary particulate matter (PM) in ambient air in Europe are exhaust and non-exhaust emissions from road traffic and combustion of solid biomass. There is convincing evidence that PM, almost regardless of source, has detrimental health effects. An important issue in health impact assessments is what metric, indicator and exposure-response function to use for different types of PM. The aim of this study is to describe sectorial contributions to PM exposure and related premature mortality for three Swedish cities: Gothenburg, Stockholm and Umea. Exposure is calculated with high spatial resolution using atmospheric dispersion models. Attributed premature mortality is calculated separately for the main local sources and the contribution from long-range transport (LRT), applying different relative risks. In general, the main part of the exposure is due to LRT, while for black carbon, the local sources are equally or more important. The major part of the premature deaths is in our assessment related to local emissions, with road traffic and residential wood combustion having the largest impact. This emphasizes the importance to resolve within-city concentration gradients when assessing exposure. It also implies that control actions on local PM emissions have a strong potential in abatement strategies. PMID:28686215

Assessment of Pneumatic Controller Emission Measurements using a High Volume Sampler at the Oil and Natural Gas Production Pads in Utah

EPA Science Inventory

Oil and Natural Gas (ONG) production facilities have the potential to emit greenhouse gases such as methane (CH4) and other hydrocarbons (HCs) to the atmosphere. ONG production sites have multiple emission sources including storage tank venting, enclosed combustion devices, engin...

Field determination of multipollutant, open area combustion source emission factors with a hexacopter unmanned aerial vehicle

EPA Science Inventory

An emission sensor/sampler system was coupled to a NASA hexacopter unmanned aerial system (UAS) to characterize gases and particles in the plume emitted from open burning of military ordnance. The UAS/sampler was tested at two field sites resulting in 33 flights at Radford, VA a...

40 CFR 74.22 - Actual SO 2 emissions rate.

Code of Federal Regulations, 2014 CFR

2014-07-01

... calculations under this section based on data submitted under § 74.20 for the following calendar year: (1) For combustion sources that commenced operation prior to January 1, 1985, the calendar year for calculating the... January 1, 1985, the calendar year for calculating the actual SO2 emissions rate shall be the first year...

40 CFR 74.22 - Actual SO2 emissions rate.

Code of Federal Regulations, 2012 CFR

2012-07-01

... calculations under this section based on data submitted under § 74.20 for the following calendar year: (1) For combustion sources that commenced operation prior to January 1, 1985, the calendar year for calculating the... January 1, 1985, the calendar year for calculating the actual SO2 emissions rate shall be the first year...

40 CFR 74.22 - Actual SO2 emissions rate.

Code of Federal Regulations, 2011 CFR

2011-07-01

... calculations under this section based on data submitted under § 74.20 for the following calendar year: (1) For combustion sources that commenced operation prior to January 1, 1985, the calendar year for calculating the... January 1, 1985, the calendar year for calculating the actual SO2 emissions rate shall be the first year...

40 CFR 74.22 - Actual SO 2 emissions rate.

Code of Federal Regulations, 2013 CFR

2013-07-01

... calculations under this section based on data submitted under § 74.20 for the following calendar year: (1) For combustion sources that commenced operation prior to January 1, 1985, the calendar year for calculating the... January 1, 1985, the calendar year for calculating the actual SO2 emissions rate shall be the first year...

40 CFR 63.6160 - In what form and how long must I keep my records?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines Notifications, Reports, and Records § 63.6160 In what form and how long must I keep my records? (a) You must...

40 CFR 63.6160 - In what form and how long must I keep my records?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants for Stationary Combustion Turbines Notifications, Reports, and Records § 63.6160 In what form and how long must I keep my records? (a) You must...

Flame blowout and pollutant emissions in vitiated combustion of conventional and bio-derived fuels

NASA Astrophysics Data System (ADS)

Singh, Bhupinder

The widening gap between the demand and supply of fossil fuels has catalyzed the exploration of alternative sources of energy. Interest in the power, water extraction and refrigeration (PoWER) cycle, proposed by the University of Florida, as well as the desirability of using biofuels in distributed generation systems, has motivated the exploration of biofuel vitiated combustion. The PoWER cycle is a novel engine cycle concept that utilizes vitiation of the air stream with externally-cooled recirculated exhaust gases at an intermediate pressure in a semi-closed cycle (SCC) loop, lowering the overall temperature of combustion. It has several advantages including fuel flexibility, reduced air flow, lower flame temperature, compactness, high efficiency at full and part load, and low emissions. Since the core engine air stream is vitiated with the externally cooled exhaust gas recirculation (EGR) stream, there is an inherent reduction in the combustion stability for a PoWER engine. The effect of EGR flow and temperature on combustion blowout stability and emissions during vitiated biofuel combustion has been characterized. The vitiated combustion performance of biofuels methyl butanoate, dimethyl ether, and ethanol have been compared with n-heptane, and varying compositions of syngas with methane fuel. In addition, at high levels of EGR a sharp reduction in the flame luminosity has been observed in our experimental tests, indicating the onset of flameless combustion. This drop in luminosity may be a result of inhibition of processes leading to the formation of radiative soot particles. One of the objectives of this study is finding the effect of EGR on soot formation, with the ultimate objective of being able to predict the boundaries of flameless combustion. Detailed chemical kinetic simulations were performed using a constant-pressure continuously stirred tank reactor (CSTR) network model developed using the Cantera combustion code, implemented in C++. Results have been presented showing comparative trends in pollutant emissions generation, flame blowout stability, and combustion efficiency. (Full text of this dissertation may be available via the University of Florida Libraries web site. Please check http://www.uflib.ufl.edu/etd.html)

Chemical composition of aerosol particles and light extinction apportionment before and during the heating season in Beijing, China

NASA Astrophysics Data System (ADS)

Wang, Qingqing; Sun, Yele; Jiang, Qi; Du, Wei; Sun, Chengzhu; Fu, Pingqing; Wang, Zifa

2015-12-01

Despite extensive efforts into characterization of the sources and formation mechanisms of severe haze pollution in the megacity of Beijing, the response of aerosol composition and optical properties to coal combustion emissions in the heating season remain poorly understood. Here we conducted a 3 month real-time measurement of submicron aerosol (PM1) composition by an Aerosol Chemical Speciation Monitor and particle light extinction by a Cavity Attenuated Phase Shift extinction monitor in Beijing, China, from 1 October to 31 December 2012. The average (±σ) PM1 concentration was 82.4 (±73.1) µg/m3 during the heating period (HP, 15 November to 31 December), which was nearly 50% higher than that before HP (1 October to 14 November). While nitrate and secondary organic aerosol (SOA) showed relatively small changes, organics, sulfate, and chloride were observed to have significant increases during HP, indicating the dominant impacts of coal combustion sources on these three species. The relative humidity-dependent composition further illustrated an important role of aqueous-phase processing for the sulfate enhancement during HP. We also observed great increases of hydrocarbon-like OA (HOA) and coal combustion OA (CCOA) during HP, which was attributed to higher emissions at lower temperatures and coal combustion emissions, respectively. The relationship between light extinction and chemical composition was investigated using a multiple linear regression model. Our results showed that the largest contributors to particle extinction were ammonium nitrate (32%) and ammonium sulfate (28%) before and during HP, respectively. In addition, the contributions of SOA and primary OA to particle light extinction were quantified. The results showed that the OA extinction was mainly caused by SOA before HP and by SOA and CCOA during HP, yet with small contributions from HOA and cooking aerosol for the entire study period. Our results elucidate substantial changes of aerosol composition, formation mechanisms, and optical properties due to coal combustion emissions and meteorological changes in the heating season.

Temporal variability in the sources and fluxes of CO2 in a residential area in an evergreen subtropical city

NASA Astrophysics Data System (ADS)

Weissert, L. F.; Salmond, J. A.; Turnbull, J. C.; Schwendenmann, L.

2016-10-01

Measurements of CO2 fluxes in temperate climates have shown that urban areas are a net source of CO2 and that photosynthetic CO2 uptake is generally not sufficient to offset local CO2 emissions. However, little is known about the role of vegetation in cities where biogenic CO2 uptake is not limited to a 2-8 months growing season. This study used the eddy covariance technique to quantify the atmospheric CO2 fluxes over a period of 12 months in a residential area in subtropical Auckland, New Zealand, where the vegetation cover (surface cover fraction: 47%) is dominated by evergreen vegetation. Radiocarbon isotope measurements of CO2 were conducted at three different times of the day (06:00-09:00, 12:00-15:00, 01:00-04:00) for four consecutive weekdays in summer and winter to differentiate anthropogenic sources of CO2 (fossil fuel combustion) from biogenic sources (ecosystem respiration, combustion of biofuel/biomass). The results reveal previously unreported patterns for CO2 fluxes, with no seasonal variability and negative (net uptake) CO2 midday fluxes throughout the year, demonstrating photosynthetic uptake by the evergreen vegetation all year-round. The winter radiocarbon measurements showed that 85% of the CO2 during the morning rush hour was attributed to fossil fuel emissions, when wind was from residential areas. However, for all other time periods radiocarbon measurements showed that fossil fuel combustion was not a large source of CO2, suggesting that biogenic processes likely dominate CO2 fluxes at this residential site. Overall, our findings highlight the importance of vegetation in residential areas to mitigate local CO2 emissions, particularly in cities with a climate that allows evergreen vegetation to maintain high photosynthetic rates over winter. As urban areas grow, urban planners need to consider the role of urban greenspace to mitigate urban CO2 emissions.

Quantifying the uncertainties of a bottom-up emission inventory of anthropogenic atmospheric pollutants in China

NASA Astrophysics Data System (ADS)

Zhao, Y.; Nielsen, C. P.; Lei, Y.; McElroy, M. B.; Hao, J.

2010-11-01

The uncertainties of a national, bottom-up inventory of Chinese emissions of anthropogenic SO2, NOx, and particulate matter (PM) of different size classes and carbonaceous species are comprehensively quantified, for the first time, using Monte Carlo simulation. The inventory is structured by seven dominant sectors: coal-fired electric power, cement, iron and steel, other industry (boiler combustion), other industry (non-combustion processes), transportation, and residential. For each parameter related to emission factors or activity-level calculations, the uncertainties, represented as probability distributions, are either statistically fitted using results of domestic field tests or, when these are lacking, estimated based on foreign or other domestic data. The uncertainties (i.e., 95% confidence intervals around the central estimates) of Chinese emissions of SO2, NOx, total PM, PM10, PM2.5, black carbon (BC), and organic carbon (OC) in 2005 are estimated to be -14%~12%, -10%~36%, -10%~36%, -12%~42% -16%~52%, -23%~130%, and -37%~117%, respectively. Variations at activity levels (e.g., energy consumption or industrial production) are not the main source of emission uncertainties. Due to narrow classification of source types, large sample sizes, and relatively high data quality, the coal-fired power sector is estimated to have the smallest emission uncertainties for all species except BC and OC. Due to poorer source classifications and a wider range of estimated emission factors, considerable uncertainties of NOx and PM emissions from cement production and boiler combustion in other industries are found. The probability distributions of emission factors for biomass burning, the largest source of BC and OC, are fitted based on very limited domestic field measurements, and special caution should thus be taken interpreting these emission uncertainties. Although Monte Carlo simulation yields narrowed estimates of uncertainties compared to previous bottom-up emission studies, the results are not always consistent with those derived from satellite observations. The results thus represent an incremental research advance; while the analysis provides current estimates of uncertainty to researchers investigating Chinese and global atmospheric transport and chemistry, it also identifies specific needs in data collection and analysis to improve on them. Strengthened quantification of emissions of the included species and other, closely associated ones - notably CO2, generated largely by the same processes and thus subject to many of the same parameter uncertainties - is essential not only for science but for the design of policies to redress critical atmospheric environmental hazards at local, regional, and global scales.

Quantifying the uncertainties of a bottom-up emission inventory of anthropogenic atmospheric pollutants in China

NASA Astrophysics Data System (ADS)

Zhao, Y.; Nielsen, C. P.; Lei, Y.; McElroy, M. B.; Hao, J.

2011-03-01

The uncertainties of a national, bottom-up inventory of Chinese emissions of anthropogenic SO2, NOx, and particulate matter (PM) of different size classes and carbonaceous species are comprehensively quantified, for the first time, using Monte Carlo simulation. The inventory is structured by seven dominant sectors: coal-fired electric power, cement, iron and steel, other industry (boiler combustion), other industry (non-combustion processes), transportation, and residential. For each parameter related to emission factors or activity-level calculations, the uncertainties, represented as probability distributions, are either statistically fitted using results of domestic field tests or, when these are lacking, estimated based on foreign or other domestic data. The uncertainties (i.e., 95% confidence intervals around the central estimates) of Chinese emissions of SO2, NOx, total PM, PM10, PM2.5, black carbon (BC), and organic carbon (OC) in 2005 are estimated to be -14%~13%, -13%~37%, -11%~38%, -14%~45%, -17%~54%, -25%~136%, and -40%~121%, respectively. Variations at activity levels (e.g., energy consumption or industrial production) are not the main source of emission uncertainties. Due to narrow classification of source types, large sample sizes, and relatively high data quality, the coal-fired power sector is estimated to have the smallest emission uncertainties for all species except BC and OC. Due to poorer source classifications and a wider range of estimated emission factors, considerable uncertainties of NOx and PM emissions from cement production and boiler combustion in other industries are found. The probability distributions of emission factors for biomass burning, the largest source of BC and OC, are fitted based on very limited domestic field measurements, and special caution should thus be taken interpreting these emission uncertainties. Although Monte Carlo simulation yields narrowed estimates of uncertainties compared to previous bottom-up emission studies, the results are not always consistent with those derived from satellite observations. The results thus represent an incremental research advance; while the analysis provides current estimates of uncertainty to researchers investigating Chinese and global atmospheric transport and chemistry, it also identifies specific needs in data collection and analysis to improve on them. Strengthened quantification of emissions of the included species and other, closely associated ones - notably CO2, generated largely by the same processes and thus subject to many of the same parameter uncertainties - is essential not only for science but for the design of policies to redress critical atmospheric environmental hazards at local, regional, and global scales.

PMF and PSCF based source apportionment of PM2.5 at a regional background site in North China

NASA Astrophysics Data System (ADS)

Zong, Zheng; Wang, Xiaoping; Tian, Chongguo; Chen, Yingjun; Fu, Shanfei; Qu, Lin; Ji, Ling; Li, Jun; Zhang, Gan

2018-05-01

To apportion regional PM2.5 (atmospheric particles with aerodynamic diameter < 2.5 μm) source types and their geographic pattern in North China, 120 daily PM2.5 samples on Beihuangcheng Island (BH, a regional background site in North China) were collected from August 20th, 2014 to September 15th, 2015 showing one-year period. After the chemical analyses on carbonaceous species, water-soluble ions and inorganic elements, various approaches, such as Mann-Kendall test, chemical mass closure, ISORROPIA II model, Positive Matrix Factorization (PMF) linked with Potential Source Contribution Function (PSCF), were used to explore the PM2.5 speciation, sources, and source regions. Consequently, distinct seasonal variations of PM2.5 and its main species were found and could be explained by varying emission source characteristics. Based on PMF model, seven source factors for PM2.5 were identified, which were coal combustion + biomass burning, vehicle emission, mineral dust, ship emission, sea salt, industry source, refined chrome industry with the contribution of 48.21%, 30.33%, 7.24%, 6.63%, 3.51%, 3.2%, and 0.88%, respectively. In addition, PSCF analysis using the daily contribution of each factor from PMF result suggested that Shandong peninsula and Hebei province were identified as the high potential region for coal combustion + biomass burning; Beijing-Tianjin-Hebei (BTH) region was the main source region for industry source; Bohai Sea and East China Sea were found to be of high source potential for ship emission; Geographical region located northwest of BH Island was possessed of high probability for sea salt; Mineral dust presumably came from the region of Mongolia; Refined chrome industry mostly came from Liaoning, Jilin province; The vehicle emission was primarily of BTH region origin, centring on metropolises, such as Beijing and Tianjin. These results provided precious implications for PM2.5 control strategies in North China.

The levels, variation characteristics, and sources of atmospheric non-methane hydrocarbon compounds during wintertime in Beijing, China

NASA Astrophysics Data System (ADS)

Liu, Chengtang; Ma, Zhuobiao; Mu, Yujing; Liu, Junfeng; Zhang, Chenglong; Zhang, Yuanyuan; Liu, Pengfei; Zhang, Hongxing

2017-09-01

Atmospheric non-methane hydrocarbon compounds (NMHCs) were measured at a sampling site in Beijing city from 15 December 2015 to 14 January 2016 to recognize their pollution levels, variation characteristics, and sources. We quantified 53 NMHCs, and the proportions of alkanes, alkenes, acetylene, and aromatics to the total NMHCs were 49.8-55.8, 21.5-24.7, 13.5-15.9, and 9.3-10.7 %, respectively. The variation trends in the NMHC concentrations were basically identical and exhibited remarkable fluctuation, which was mainly ascribed to the variation in meteorological conditions, especially wind speed. The diurnal variations in NMHCs on clear days exhibited two peaks during the morning and evening rush hours, whereas the rush hours' peaks diminished or even disappeared on the haze days, implying that the relative contribution of the vehicular emissions to atmospheric NMHCs depended on the pollution status. Two evident peaks of the propane / propene ratios appeared in the early morning before sun rise and at noontime on clear days, whereas only one peak occurred in the afternoon during the haze days, which were attributed to the relatively fast reactions of propene with OH, NO3, and O3. Based on the chemical kinetic equations, the daytime OH concentrations were calculated to be in the range of 3. 47 × 105-1. 04 × 106 molecules cm-3 on clear days and 6. 42 × 105-2. 35 × 106 molecules cm-3 on haze days. The nighttime NO3 concentrations were calculated to be in the range of 2. 82 × 109-4. 86 × 109 molecules cm-3 on clear days. The correlation coefficients of typical hydrocarbon pairs (benzene / toluene, o-xylene / m,p-xylene, isopentane / n-pentane, etc.) revealed that vehicular emissions and coal combustion were important sources for atmospheric NMHCs in Beijing during the wintertime. Five major emission sources for atmospheric NMHCs in Beijing during the wintertime were further identified by positive matrix factorization (PMF), including gasoline-related emissions (gasoline exhaust and evaporation), coal combustion, diesel exhaust, acetylene-related emissions, and consumer and household products. Coal combustion (probably domestic coal combustion) was found to make the greatest contribution (29.6-33.4 %) to atmospheric NMHCs during haze days.

Effect [of] co-combustion of sewage sludge and biomass on combustion behavior and emissions in pulverized fuel systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spliethoff, H.; Hein, K.R.G.

1999-07-01

Biomass not only has a considerable potential as an additional fuel source but also shows a reasonable cost level in comparison to other renewable energies. The practicable fuel types are both residual material from forestry and agriculture, such as wood or straw, and especially cultivated reproducible feedstock such as Miscanthus Sinensis, whole cereal plants, poplars, or willows. Besides as single fuel, it is also considered to be sensible to utilize biomass in co-combustion in existing firing systems, such as pc-fired power stations. Biomass or sewage sludge utilized as additional fuel in coal combustion systems has consequences on combustion behavior, emissions,more » corrosion and residual matter. The effects of burning sewage sludge and agricultural residuals such as straw and manure as well as specially grown energy plants in combination with coal were studied in a 0.5 MW pulverized fuel test facility and a 20 kW electrically heated combustor. A major aspect of the investigations had been the required preparation and milling of the additional fuels. The investigations showed that in co-combustion of straw with coal, a grinding of 6 mm and finer is sufficient. The definitely coarser milling degree of biomass delays combustion and is observable by in-flame measurements. The investigations reveal that biomass addition has a positive effect on emissions. Since biomass in most cases contains considerably less sulphur than coal, an increasing biomass share in the thermal output makes the SO{sub 2} emissions decrease proportionally. In addition, SO{sub 2} can partly be captured in the ash by the alkaline-earth fractions of the biomass ash. As for sewage sludge, the emissions of SO{sub 2} correlate with the sulphur content of the fuel and, hence, rise with an increasing share of this biomass. Independently from the type, biomass shows a considerably stronger release of volatile matter. This latter fact may have a positive impact on NOx emissions when NOx-reducing techniques are applied. Within the framework of these investigations the following configurations were used: (1) unstaged combustion with preblending of coal and biomass, (2) air-staged combustion with preblending of coal and biomass, (3) reburning with biomass as reduction fuel, and (4) various burner configurations. The results show that the burner design and operation mode have a great influence on the NOx emissions of combined flames. Air staging and reburning are effective measures to reduce the NOx emissions of combined fuels. NOx emissions smaller than 300 mg/m at 6% O{sub 2} can be reached with all fuels.« less

Anthropogenic atmospheric nickel emissions and its distribution characteristics in China.

PubMed

Tian, H Z; Lu, L; Cheng, K; Hao, J M; Zhao, D; Wang, Y; Jia, W X; Qiu, P P

2012-02-15

Nickel and its compounds are considered as potential human carcinogens, and atmospheric nickel is one of the major routes for human exposure. By applying the best available fuel-based or product-based emission factors and annual activity levels, a multiple-year comprehensive inventory of anthropogenic atmospheric nickel emissions in China is presented with temporal trend and spatial resolutions for the period of 1980-2009 from both fuels combustion sources and industrial producing processes. We estimate that the total atmospheric nickel emissions from all the sources have increased from 1096.07 t in 1980 to 3933.71 t in 2009, at an average annual growth rate of 4.5%. Therein, coal combustion is the leading source, attributing 63.4% of the national total nickel emissions in 2009; liquid fuels consumption ranks the second, contributing 12.4% of the totals; biofuels burning accounts for 8.4% and the remaining sources together contribute 15.8% of the totals. Significant spatial variations are demonstrated among provincial emissions and the most concentrated regions are the highly industrialized and densely populated areas like the Yangtze River Delta, the Pearl River Delta and the Beijing-Tianjin-Hebei region. Moreover, the overall uncertainties are estimated at -32.6%-37.7% by using Monte Carlo simulation, most of which come from non-ferrous metals smelting category, implying the urgent need for further investigation and field tests. This article may help to combat the increasing stress on air heavy metals pollution in China and provide useful information to calculate global mass balance models for hazardous trace elements. Copyright © 2011 Elsevier B.V. All rights reserved.

General Conformity Training Modules: Appendix A Sample Emissions Calculations

EPA Pesticide Factsheets

Appendix A of the training modules gives example calculations for external and internal combustion sources, construction, fuel storage and transfer, on-road vehicles, aircraft operations, storage piles, and paved roads.

X-Ray Radiography Measurements of the Thermal Energy in Spark Ignition Plasma at Variable Ambient Conditions

DOE PAGES

Matusik, Katarzyna E.; Duke, Daniel J.; Kastengren, Alan L.; ...

2017-04-09

The sparking behavior in an internal combustion engine affects the fuel efficiency, engine-out emissions, and general drivability of a vehicle. As emissions regulations become progressively stringent, combustion strategies, including exhaust gas recirculation (EGR), lean-burn, and turbocharging are receiving increasing attention as models of higher efficiency advanced combustion engines with reduced emissions levels. Because these new strategies affect the working environment of the spark plug, ongoing research strives to understand the influence of external factors on the spark ignition process. Due to the short time and length scales involved and the harsh environment, experimental quantification of the deposited energy from themore » sparking event is difficult to obtain. We present the results of x-ray radiography measurements of spark ignition plasma generated by a conventional spark plug. Our measurements were performed at the 7-BM beamline of the Advanced Photon Source at Argonne National Laboratory. The synchrotron x-ray source enables time-resolved measurements of the density change due to glow discharge in the spark gap with 153 ns temporal and 5 μm spatial resolutions. We also explore the effects of charging time, EGR-relevant gas compositions, and gas pressure on the sparking behavior. We also quantify the influence of the measurement technique on the obtained results.« less

Supplement a to compilation of air pollutant emission factors. Volume 1. Stationary point and area sources. Fifth edition

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-02-01

This Supplement to AP-42 addresses pollutant-generating activity from Bituminous and Subbituminous Coal Combustion; Anthracite Coal Combustion; Fuel Oil Combustion; Natural Gas Combustion; Wood Waste Combustion in Boilers; Lignite Combustion; Waste Oil Combustion: Stationary Gas Turbines for Electricity Generation; Heavy-duty Natural Gas-fired Pipeline Compressor Engines; Large Stationary Diesel and all Stationary Dual-fuel engines; Natural Gas Processing; Organic Liquid Storage Tanks; Meat Smokehouses; Meat Rendering Plants; Canned Fruits and Vegetables; Dehydrated Fruits and Vegetables; Pickles, Sauces and Salad Dressing; Grain Elevators and Processes; Cereal Breakfast Foods; Pasta Manufacturing; Vegetable Oil Processing; Wines and Brandy; Coffee Roasting; Charcoal; Coal Cleaning; Frit Manufacturing; Sandmore » and Gravel Processing; Diatomite Processing; Talc Processing; Vermiculite Processing; paved Roads; and Unpaved Roads. Also included is information on Generalized Particle Size Distributions.« less

Sources and sinks of methane in the African Savanna. CH4 emissions from biomass burning

NASA Astrophysics Data System (ADS)

Delmas, R. A.; Marenco, A.; Tathy, J. P.; Cros, B.; Baudet, J. G. R.

1991-04-01

Sources and sinks of atmospheric methane are studied in savanna regions of west and central Africa. Flux measured over dry savanna soils, using static chambers, is always negative the average uptake rate being 2×1010 molecules/cm2/s. In these regions, sources are linked to biomass burning. Methane and CO2 emission from combustion of savanna plants and wood is studied by both field experiments and laboratory experiments using a combustion chamber. For savanna plants most of the carbon (85%) contained in the biomaterial is volatilized as CO2 and 0.1 to 0.25% as methane. For graminaceous plants like loudetia simplex the ratio C-CH4/C-CO2 is 0.11%; it is 0.28% for hyparrhenia the other main type of savanna plants and it attains 1.4% for the combustion of wood. In natural fire plumes this ratio is around 0.26% for savanna fires and 0.56 to 2.22% for forest fires. These results show that methane release is highly dependent on the type of combustion. Methane to CO2 ratios are also studied in vertical profiles in the troposphere taken during the TROPOZ I campaign, an aerial research expedition carried out over west Africa during the bushfire period. Within polluted layers, the average ratio of CH4 to CO2 excess over ambient air concentration is 0.34%. These results show that biomass burning in tropical Africa constitutes an important source of atmospheric methane estimated to about 9.2×106 T(CH4)/yr.

40 CFR 60.1590 - When must I complete each increment of progress?

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30, 1999 Model Rule...

Microjet burners for molecular-beam sources and combustion studies

NASA Astrophysics Data System (ADS)

Groeger, Wolfgang; Fenn, John B.

1988-09-01

A novel microjet burner is described in which combustion is stabilized by a hot wall. The scale is so small that the entire burner flow can be passed through a nozzle only 0.2 mm or less in diameter into an evacuated chamber to form a supersonic free jet with expansion so rapid that all collisional processes in the jet gas are frozen in a microsecond or less. This burner can be used to provide high-temperature source gas for free jet expansion to produce intense beams of internally hot molecules. A more immediate use would seem to be in the analysis of combustion products and perhaps intermediates by various kinds of spectroscopies without some of the perturbation effects encountered in probe sampling of flames and other types of combustion devices. As an example of the latter application of this new tool, we present infrared emission spectra for jet gas obtained from the combustion of oxygen-hydrocarbon mixtures both fuel-rich and fuel-lean operation. In addition, we show results obtained by mass spectrometric analysis of the combustion products.

North America carbon dioxide sources and sinks: magnitude, attribution, and uncertainty

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Anthony W.; Hayes, Daniel J.; Huntzinger, Deborah N.

2012-12-01

North America is both a source and sink of atmospheric CO2. Sources, predominately fossil-fuel combustion in the United States along with contributions from deforestation in Mexico, add CO2 to the atmosphere. Most North America ecosystems, particularly regrowing forests in the United States, are sinks for atmospheric CO2. CO2 is removed from the atmosphere in photosynthesis, converted into biomass and stored as carbon in vegetation, soil and wood products. Fossil-fuel emissions dominate the North American source-sink balance. North America is a net source of atmospheric CO2 with ecosystem sinks balancing approximately 35% of fossil-fuel CO2 emissions from North America.

Source apportionment of PM(2.5) in the harbour-industrial area of Brindisi (Italy): identification and estimation of the contribution of in-port ship emissions.

PubMed

Cesari, D; Genga, A; Ielpo, P; Siciliano, M; Mascolo, G; Grasso, F M; Contini, D

2014-11-01

Harbours are important for economic and social development of coastal areas but they also represent an anthropogenic source of emissions often located near urban centres and industrial areas. This increases the difficulties in distinguishing the harbour contribution with respect to other sources. The aim of this work is the characterisation of main sources of PM2.5 acting on the Brindisi harbour-industrial area, trying to pinpoint the contribution of in-port ship emissions to primary and secondary PM2.5. Brindisi is an important port-city of the Adriatic Sea considered a hot-spot for anthropogenic environmental pressures at National level. Measurements were performed collecting PM2.5 samples and characterising the concentrations of 23 chemical species (water soluble organic and inorganic carbon; major ions: SO4(2-), NO3(-), NH4(+), Cl(-), C2O4(2-), Na(+), K(+), Mg(2+), Ca(2+); and elements: Ni, Cu, V, Mn, As, Pb, Cr, Sb, Fe, Al, Zn, and Ti). These species represent, on average, 51.4% of PM2.5 and were used for source apportionment via PMF. The contributions of eight sources were estimated: crustal (16.4±0.9% of PM2.5), aged marine (2.6±0.5%), crustal carbonates (7.7±0.3%), ammonium sulphate (27.3±0.8%), biomass burning-fires (11.7±0.7%), traffic (16.4±1.7 %), industrial (0.4±0.3%) and a mixed source oil combustion-industrial including ship emissions in harbour (15.3±1.3%). The PMF did not separate the in-port ship emission contribution from industrial releases. The correlation of estimated contribution with meteorology showed directionality with an increase of oil combustion and sulphate contribution in the harbour direction with respect to the direction of the urban area and an increase of the V/Ni ratio. This allowed for the use of V as marker of primary ship contribution to PM2.5 (2.8%+/-1.1%). The secondary contribution of oil combustion to non-sea-salt-sulphate, nssSO4(2-), was estimated to be 1.3 μg/m(3) (about 40% of total nssSO4(2-) or 11% of PM2.5). Copyright © 2014 Elsevier B.V. All rights reserved.

Chemical characterization and source identification of PM2.5 at multiple sites in the Beijing-Tianjin-Hebei region, China

NASA Astrophysics Data System (ADS)

Huang, Xiaojuan; Liu, Zirui; Liu, Jingyun; Hu, Bo; Wen, Tianxue; Tang, Guiqian; Zhang, Junke; Wu, Fangkun; Ji, Dongsheng; Wang, Lili; Wang, Yuesi

2017-11-01

The simultaneous observation and analysis of atmospheric fine particles (PM2.5) on a regional scale is an important approach to develop control strategies for haze pollution. In this study, samples of filtered PM2.5 were collected simultaneously at three urban sites (Beijing, Tianjin, and Shijiazhuang) and at a regional background site (Xinglong) in the Beijing-Tianjin-Hebei (BTH) region from June 2014 to April 2015. The PM2.5 at the four sites was mainly comprised of organic matter, secondary inorganic ions, and mineral dust. Positive matrix factorization (PMF) demonstrated that, on an annual basis, secondary inorganic aerosol was the largest PM2.5 source in this region, accounting for 29.2-40.5 % of the PM2.5 mass at the urban sites; the second-largest PM2.5 source was motor vehicle exhaust, particularly in Beijing (24.9 %), whereas coal combustion was also a large source in Tianjin (12.4 %) and Shijiazhuang (15.5 %), with particular dominance in winter. Secondary inorganic aerosol plays a vital role in the haze process, with the exception of the spring haze in Shijiazhuang and Tianjin, for which the dust source was crucial. In addition to secondary transformations, local direct emissions (coal combustion and motor vehicle exhaust) significantly contribute to the winter haze at the urban sites. Moreover, with the aggravation of haze pollution, the OC / EC mass ratio of PM2.5 decreased considerably and the nitrate-rich secondary aerosol increased during all four seasons in Beijing, both of which indicate that local motor vehicle emissions significantly contribute to the severe haze episodes in Beijing. To assess the impacts of regional transport on haze pollution, the PMF results were further processed with backward-trajectory cluster analysis, revealing that haze pollution usually occurred when air masses originating from polluted industrial regions in the south prevailed and is characterized by high PM2.5 loadings with considerable contributions from secondary aerosols. This study suggests that control strategies to mitigate haze pollution in the BTH region should focus on the reduction of gaseous precursor emissions from fossil fuel combustion (motor vehicle emissions in Beijing and coal combustion in Tianjin, Hebei, and nearby provinces).

Quantification of uncertainty associated with United States high resolution fossil fuel CO2 emissions: updates, challenges and future plans

NASA Astrophysics Data System (ADS)

Gurney, K. R.; Chandrasekaran, V.; Mendoza, D. L.; Geethakumar, S.

2010-12-01

The Vulcan Project has estimated United States fossil fuel CO2 emissions at the hourly time scale and at spatial scales below the county level for the year 2002. Vulcan is built from a wide variety of observational data streams including regulated air pollutant emissions reporting, traffic monitoring, energy statistics, and US census data. In addition to these data sets, Vulcan relies on a series of modeling assumptions and constructs to interpolate in space, time and transform non-CO2 reporting into an estimate of CO2 combustion emissions. The recent version 2.0 of the Vulcan inventory has produced advances in a number of categories with particular emphasis on improved temporal structure. Onroad transportation emissions now avail of roughly 5000 automated traffic count monitors allowing for much improved diurnal and weekly time structure in our onroad transportation emissions. Though the inventory shows excellent agreement with independent national-level CO2 emissions estimates, uncertainty quantification has been a challenging task given the large number of data sources and numerous modeling assumptions. However, we have now accomplished a complete uncertainty estimate across all the Vulcan economic sectors and will present uncertainty estimates as a function of space, time, sector and fuel. We find that, like the underlying distribution of CO2 emissions themselves, the uncertainty is also strongly lognormal with high uncertainty associated with a relatively small number of locations. These locations typically are locations reliant upon coal combustion as the dominant CO2 source. We will also compare and contrast Vulcan fossil fuel CO2 emissions estimates against estimates built from DOE fuel-based surveys at the state level. We conclude that much of the difference between the Vulcan inventory and DOE statistics are not due to biased estimation but mechanistic differences in supply versus demand and combustion in space/time.

Assessing fire emissions from tropical savanna and forests of central Brazil

Treesearch

Philip J. Riggan; James A. Brass; Robert N. Lockwood

1993-01-01

Wildfires in tropical forest and savanna are a strong source of trace gas and particulate emissions to the atmosphere, but estimates of the continental-scale impacts are limited by large uncertainties in the rates of fire occurrence and biomass combustion. Satellite-based remote sensing offers promise for characterizing fire physical properties and impacts on the...

40 CFR 98.282 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GREENHOUSE GAS REPORTING Silicon Carbide Production § 98.282 GHGs to report. You must report: (a) CO2 process emissions from all silicon carbide process units or furnaces combined. (b) CO2, CH4, and N2O emissions from... Stationary Fuel Combustion Sources) by following the requirements of subpart C. [74 FR 56374, Oct. 30, 2009...

40 CFR 98.222 - GHGs to report.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GREENHOUSE GAS REPORTING Nitric Acid Production § 98.222 GHGs to report. (a) You must report N2O process emissions from each nitric acid production train as required by this subpart. (b) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O...

40 CFR 98.222 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GREENHOUSE GAS REPORTING Nitric Acid Production § 98.222 GHGs to report. (a) You must report N2O process emissions from each nitric acid production train as required by this subpart. (b) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O...

40 CFR 98.222 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GREENHOUSE GAS REPORTING Nitric Acid Production § 98.222 GHGs to report. (a) You must report N2O process emissions from each nitric acid production train as required by this subpart. (b) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O...

40 CFR 98.222 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GREENHOUSE GAS REPORTING Nitric Acid Production § 98.222 GHGs to report. (a) You must report N2O process emissions from each nitric acid production train as required by this subpart. (b) You must report under subpart C of this part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O...

40 CFR 60.2710 - How do I demonstrate continuous compliance with the emission limitations and the operating limits?

Code of Federal Regulations, 2012 CFR

2012-07-01

... NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid...-to-fuel switch. (4) If you own or operate an existing commercial or industrial combustion unit that... internal and external corrosion. (3) Use a pressure sensor with a minimum tolerance of 1.27 centimeters of...

Inventory of U.S. 2012 dioxin emissions to atmosphere.

PubMed

Dwyer, Henri; Themelis, Nickolas J

2015-12-01

In 2006, the U.S. EPA published an inventory of dioxin emissions for the U.S. covering the period from 1987-2000. This paper is an updated inventory of all U.S. dioxin emissions to the atmosphere in the year 2012. The sources of emissions of polychlorinated dibenzodioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs), collectively referred to in this paper as "dioxins", were separated into two classes: controlled industrial and open burning sources. Controlled source emissions decreased 95.5% from 14.0 kg TEQ in 1987 to 0.6 kg in 2012. Open burning source emissions increased from 2.3 kg TEQ in 1987 to 2.9 kg in 2012. The 2012 dioxin emissions from 53 U.S. waste-to-energy (WTE) power plants were compiled on the basis of detailed data obtained from the two major U.S. WTE companies, representing 84% of the total MSW combusted (27.4 million metric tons). The dioxin emissions of all U.S. WTE plants in 2012 were 3.4 g TEQ and represented 0.54% of the controlled industrial dioxin emissions, and 0.09% of all dioxin emissions from controlled and open burning sources. Copyright © 2015. Published by Elsevier Ltd.

Evaluation of costs associated with atmospheric mercury emission reductions from coal combustion in China in 2010 and projections for 2020.

PubMed

Zhang, Yue; Ye, Xuejie; Yang, Tianjun; Li, Jinling; Chen, Long; Zhang, Wei; Wang, Xuejun

2018-01-01

Coal combustion is the most significant anthropogenic mercury emission source in China. In 2013, China signed the Minamata Convention affirming that mercury emissions should be controlled more strictly. Therefore, an evaluation of the costs associated with atmospheric mercury emission reductions from China's coal combustion is essential. In this study, we estimated mercury abatement costs for coal combustion in China for 2010, based on a provincial technology-based mercury emission inventory. In addition, four scenarios were used to project abatement costs for 2020. Our results indicate that actual mercury emission related to coal combustion in 2010 was 300.8Mg, indicating a reduction amount of 174.7Mg. Under a policy-controlled scenario for 2020, approximately 49% of this mercury could be removed using air pollution control devices, making mercury emissions in 2020 equal to or lower than in 2010. The total abatement cost associated with mercury emissions in 2010 was 50.2×10 9 RMB. In contrast, the total abatement costs for 2020 under baseline versus policy-controlled scenarios, having high-energy and low-energy consumption, would be 32.0×10 9 versus 51.2×10 9 , and 27.4×10 9 versus 43.9×10 9 RMB, respectively. The main expense is associated with flue gas desulfurization. The unit abatement cost of mercury emissions in 2010 was 288×10 3 RMB/(kgHg). The unit abatement costs projected for 2020 under a baseline, a policy-controlled, and an United Nations Environmental Programme scenario would be 143×10 3 , 172×10 3 and 1066×10 3 RMB/(kgHg), respectively. These results are much lower than other international ones. However, the relative costs to China in terms of GPD are higher than in most developed countries. We calculated that abatement costs related to mercury emissions accounted for about 0.14% of the GDP of China in 2010, but would be between 0.03% and 0.06% in 2020. This decrease in abatement costs in terms of GDP suggests that various policy-controlled scenarios would be viable. Copyright © 2017 Elsevier B.V. All rights reserved.

Suresh K. AggarwalQuantified Analysis of a Production Diesel Injector Using X-Ray Radiography and Engine Diagnostics

NASA Astrophysics Data System (ADS)

Ramirez, Anita I.

The work presented in this thesis pursues further the understanding of fuel spray, combustion, performance, and emissions in an internal combustion engine. Various experimental techniques including x-ray radiography, injection rate measurement, and in-cylinder endoscopy are employed in this work to characterize the effects of various upstream conditions such as injection rate profile and fuel physical properties. A single non-evaporating spray from a 6-hole full-production Hydraulically Actuated Electronically Controlled Unit Injector (HEUI) nozzle is studied under engine-like ambient densities with x-ray radiography at the Advanced Photon Source (APS) of Argonne National Laboratory (ANL). Two different injection pressures were investigated and parameters such as fuel mass distribution, spray penetration, cone angle, and spray velocity were obtained. The data acquired with x-ray radiography is used for the development and validation of improved Computational Fluid Dynamic (CFD) models. Rate of injection is studied using the same HEUI in a single cylinder Caterpillar test engine. The injection rate profile is altered to have three levels of initial injection pressure rise. Combustion behavior, engine performance, and emissions information was acquired for three rate profile variations. It is found that NOx emission reduction is achieved when the SOI timing is constant at the penalty of lower power generated in the cycle. However, if CA50 is aligned amongst the three profiles, the NOx emissions and power are constant with a slight penalty in CO emissions. The influence of physical and chemical parameters of fuel is examined in a study of the heavy alcohol, phytol (C20H40O), in internal combustion engine application. Phytol is blended with diesel in 5%, 10%, and 20% by volume. Combustion behavior is similar between pure diesel and the phytol/diesel blends with small differences noted in peak cylinder pressure, ignition delay, and heat release rate in the premix burn phase. Diesel/phytol blends yield marginally lower power values. In-cylinder soot radiation images show combustion instability at the start of the event for the 20% phytol/diesel blend. Overall, NOx emissions are comparable across the different fuels used and no discernible trend is found in CO emissions.

Small Municipal Waste Combustion Units Air Toxics Rules Fact Sheets

EPA Pesticide Factsheets

This page contains several fact sheets with information regarding the final New Source Performance Standards (NSPS), Emission Guidelines, and Compliance Times regulations. This document provides a summary of the information for these regulations.

Fine particulate matter emissions inventories: comparisons of emissions estimates with observations from recent field programs.

PubMed

Simon, Heather; Allen, David T; Wittig, Ann E

2008-02-01

Emissions inventories of fine particulate matter (PM2.5) were compared with estimates of emissions based on data emerging from U.S. Environment Protection Agency Particulate Matter Supersites and other field programs. Six source categories for PM2.5 emissions were reviewed: on-road mobile sources, nonroad mobile sources, cooking, biomass combustion, fugitive dust, and stationary sources. Ammonia emissions from all of the source categories were also examined. Regional emissions inventories of PM in the exhaust from on-road and nonroad sources were generally consistent with ambient observations, though uncertainties in some emission factors were twice as large as the emission factors. In contrast, emissions inventories of road dust were up to an order of magnitude larger than ambient observations, and estimated brake wear and tire dust emissions were half as large as ambient observations in urban areas. Although comprehensive nationwide emissions inventories of PM2.5 from cooking sources and biomass burning are not yet available, observational data in urban areas suggest that cooking sources account for approximately 5-20% of total primary emissions (excluding dust), and biomass burning sources are highly dependent on region. Finally, relatively few observational data were available to assess the accuracy of emission estimates for stationary sources. Overall, the uncertainties in primary emissions for PM2.s are substantial. Similar uncertainties exist for ammonia emissions. Because of these uncertainties, the design of PM2.5 control strategies should be based on inventories that have been refined by a combination of bottom-up and top-down methods.

Combustion and NOx emissions in deep-air-staging combustion of char in a circulating fluidized bed

NASA Astrophysics Data System (ADS)

Gong, Zhiqiang; Wang, Zhentong; Wang, Lei; Du, Aixun

2017-10-01

Combustion and NOx emissions in deep-air-staging (with higher level secondary air (SA) injection) combustion of char have been investigated in a CFB test rig. A good fluidized condition and uniform temperature distribution can be achieved with injection of higher level SA. NOx emission decreases with injection of higher level SA and the reduction effect is more obvious at higher temperature. NOx emission decreases with combustion temperature increasing for char combustion.

Organic tracer-based source analysis of PM2.5 organic and elemental carbon: A case study at Dongguan in the Pearl River Delta, China

NASA Astrophysics Data System (ADS)

Wang, Qiong Qiong; Huang, X. H. Hilda; Zhang, Ting; Zhang, Qingyan; Feng, Yongming; Yuan, Zibing; Wu, Dui; Lau, Alexis K. H.; Yu, Jian Zhen

2015-10-01

Organic carbon (OC) and elemental carbon (EC) are major constituents of PM2.5 and their source apportionment remains a challenging task due to the great diversity of their sources and lack of source-specific tracer data. In this work, sources of OC and EC are investigated using positive matrix factorization (PMF) analysis of PM2.5 chemical composition data, including major ions, OC, EC, elements, and organic molecular source markers, for a set of 156 filter samples collected over three years from 2010 to 2012 at Dongguan in the Pearl River Delta, China. The key organic tracers include levoglucosan, mannosan, hopanes, C27-C33n-alkanes, and polycyclic aromatic hydrocarbons (PAHs). Using these species as input for the PMF model, nine factors were resolved. Among them, biomass burning and coal combustion were significant sources contributing 15-17% of OC and 24-30% and 34-35% of EC, respectively. Industrial emissions and ship emissions, identified through their characteristic metal signatures, contributed 16-24% and 7-8% of OC and 8-11% and 16-17% of EC, respectively. Vehicle exhaust was a less significant source, accounting for 3-4% of OC and 5-8% of EC. Secondary OC, taken to be the sum of OC present in secondary sulfate and nitrate formation source factors, made up 27-36% of OC. Plastic burning, identified through 1,3,5-triphenylbenzene as a tracer, was a less important source for OC(≤4%) and EC (5-10%), but a significant source for PAHs at this site. The utility of organic source tracers was demonstrated by comparing PMF runs with different combinations of organic tracers removed from the input species list. Levoglucosan and mannosan were important additions to distinguish biomass burning from coal combustion by reducing collinearity among source profiles. Inclusion of hopanes and 1,3,5-triphenylbenzene was found to be necessary in resolving the less significant sources vehicle exhaust and plastic burning. Inclusion of C27-C33n-alkanes and PAHs can influence the source profiles resolved by PMF and thereby affect the source contributions to OC and EC. Considerably more OC (44% vs. 27% of OC) was apportioned to the secondary factors when only major components were considered in comparison with the PMF analysis with the full suite of organic tracers, mainly at the expense of coal combustion and industrial emissions. EC apportionment to the few major combustion sources was found more sensitive to inclusion of organic tracers than OC apportionment, with PAHs playing a prominent role. This work demonstrates the importance of having distinct organic tracers in identifying and quantifying OC and EC sources.

Sources and elemental composition of ambient PM(2.5) in three European cities.

PubMed

Vallius, M; Janssen, N A H; Heinrich, J; Hoek, G; Ruuskanen, J; Cyrys, J; Van Grieken, R; de Hartog, J J; Kreyling, W G; Pekkanen, J

2005-01-20

Source apportionment of urban fine particle mass (PM(2.5)) was performed from data collected during 1998-1999 in Amsterdam (The Netherlands), Erfurt (Germany) and Helsinki (Finland), using principal component analysis (PCA) and multiple linear regression. Six source categories of PM(2.5) were identified in Amsterdam. They were traffic-related particles (30% of the average PM(2.5)), secondary particles (34%), crustal material (7%), oil combustion (11%), industrial and incineration processes (9%), and sea salt (2%). The unidentified PM(2.5) fraction was 7% on the average. In Erfurt, four source categories were extracted with some difficulties in interpretation of source profiles. They were combustion emissions related to traffic (32%), secondary PM (32%), crustal material (21%) and industrial processes (8%). In Erfurt, 3% of PM(2.5) remained unidentified. Air pollution data and source apportionment results from the two Central European cities were compared to previously published results from Helsinki, where about 80% of average PM(2.5) was attributed to transboundary air pollution and particles from traffic and other regional combustion sources. Our results indicate that secondary particles and local combustion processes (mainly traffic) were the most important source categories in all cities; their impact on the average PM(2.5) was almost equal in Amsterdam and Erfurt whereas, in Helsinki, secondary particles made up for as much as half of the total average PM(2.5).

Spatial Variability of Mercury Wet Deposition in Eastern Ohio: Summertime Meteorological Case Study Analysis of Local Source Influences

EPA Science Inventory

Extensive exploration of event precipitation data in the Ohio River Valley indicates that coal combustion emissions play an important role in mercury (Hg) wet deposition. During July-September 2006, an intensive study was undertaken to discern the degree of local source influence...

SOURCE SAMPLING FINE PARTICULATE MATTER--INSTITUTIONAL OIL-FIRED BOILER

EPA Science Inventory

EPA seeks to understand the correlation between ambient fine PM and adverse human health effects, and there are no reliable emission factors to use for estimating PM2.5 or NH3. The most common source of directly emitted PM2.5 is incomplete combustion of fossil or biomass fuels. M...

Concentration, ozone formation potential and source analysis of volatile organic compounds (VOCs) in a thermal power station centralized area: A study in Shuozhou, China.

PubMed

Yan, Yulong; Peng, Lin; Li, Rumei; Li, Yinghui; Li, Lijuan; Bai, Huiling

2017-04-01

Volatile organic compounds (VOCs) from two sampling sites (HB and XB) in a power station centralized area, in Shuozhou city, China, were sampled by stainless steel canisters and measured by gas chromatography-mass selective detection/flame ionization detection (GC-MSD/FID) in the spring and autumn of 2014. The concentration of VOCs was higher in the autumn (HB, 96.87 μg/m 3 ; XB, 58.94 μg/m 3 ) than in the spring (HB, 41.49 μg/m 3 ; XB, 43.46 μg/m 3 ), as lower wind speed in the autumn could lead to pollutant accumulation, especially at HB, which is a new urban area surrounded by residential areas and a transportation hub. Alkanes were the dominant group at both HB and XB in both sampling periods, but the contribution of aromatic pollutants at HB in the autumn was much higher than that of the other alkanes (11.16-19.55%). Compared to other cities, BTEX pollution in Shuozhou was among the lowest levels in the world. Because of the high levels of aromatic pollutants, the ozone formation potential increased significantly at HB in the autumn. Using the ratio analyses to identify the age of the air masses and analyze the sources, the results showed that the atmospheric VOCs at XB were strongly influenced by the remote sources of coal combustion, while at HB in the spring and autumn were affected by the remote sources of coal combustion and local sources of vehicle emission, respectively. Source analysis conducted using the Positive Matrix Factorization (PMF) model at Shuozhou showed that coal combustion and vehicle emissions made the two largest contributions (29.98% and 21.25%, respectively) to atmospheric VOCs. With further economic restructuring, the influence of vehicle emissions on the air quality should become more significant, indicating that controlling vehicle emissions is key to reducing the air pollution. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fossil vs. non-fossil sources of fine carbonaceous aerosols in four Chinese cities during the extreme winter haze episode in 2013

NASA Astrophysics Data System (ADS)

Zhang, Y.-L.; Huang, R.-J.; El Haddad, I.; Ho, K.-F.; Cao, J.-J.; Han, Y.; Zotter, P.; Bozzetti, C.; Daellenbach, K. R.; Canonaco, F.; Slowik, J. G.; Salazar, G.; Schwikowski, M.; Schnelle-Kreis, J.; Abbaszade, G.; Zimmermann, R.; Baltensperger, U.; Prévôt, A. S. H.; Szidat, S.

2014-10-01

During winter 2013, extremely high concentrations (i.e. 4-20 times higher than the World Health Organization guideline) of PM2.5 (particulate matter with an aerodynamic diameter <2.5 μm) were reported in several large cities in China. In this work, source apportionment of fine carbonaceous aerosols during this haze episode was conducted at four major cities in China including Xian, Beijing, Shanghai and Guangzhou. An effective statistical analysis of a combined dataset from elemental carbon (EC) and organic carbon (OC), radiocarbon (14C) and biomass-burning marker measurements using Latin-hypercube sampling allowed a quantitative source apportionment of carbonaceous aerosols. We found that fossil emissions from coal combustion and vehicle exhaust dominated EC with a mean contribution of 75 ± 8% at all sites. The remaining 25 ± 8% was exclusively attributed to biomass combustion, consistent with the measurements of biomass-burning markers such as anhydrosugars (levoglucosan and mannosan) and water-soluble potassium (K+). With a combination of the levoglucosan-to-mannosan and levoglucosan-to-K+ ratios, the major source of biomass burning in winter in China is suggested to be combustion of crop residues. The contribution of fossil sources to OC was highest in Beijing (58 ± 5%) and decreased from Shanghai (49 ± 2%) to Xian (38 ± 3%) and Guangzhou (35 ± 7%). Generally, a larger fraction of fossil OC was rather from secondary origins than primary sources for all sites. Non-fossil sources accounted on average for 55 ± 10% and 48 ± 9% of OC and TC, respectively, which suggests that non-fossil emissions were very important contributors of urban carbonaceous aerosols in China. The primary biomass-burning emissions accounted for 40 ± 8%, 48 ± 18%, 53 ± 4% and 65 ± 26% of non-fossil OC for Xian, Beijing, Shanghai and Guangzhou, respectively. Other non-fossil sources excluding primary biomass-burning were mainly attributed to formation of secondary organic carbon (SOC) from non-fossil precursors such as biomass-burning emissions. For each site, we also compared samples from moderately with heavily polluted days according to particulate matter mass. Despite a significant increase of absolute mass concentrations of primary emissions from both, fossil and non-fossil sources, during the heavily polluted events, their relative contribution to TC was even decreased, whereas the portion of SOC was consistently increased at all sites. This observation indicates that SOC was an important fraction in the increment of carbonaceous aerosols during the haze episode in China.

Polycyclic aromatic hydrocarbon emissions from the combustion of alternative fuels in a gas turbine engine.

PubMed

Christie, Simon; Raper, David; Lee, David S; Williams, Paul I; Rye, Lucas; Blakey, Simon; Wilson, Chris W; Lobo, Prem; Hagen, Donald; Whitefield, Philip D

2012-06-05

We report on the particulate-bound polycyclic aromatic hydrocarbons (PAH) in the exhaust of a test-bed gas turbine engine when powered by Jet A-1 aviation fuel and a number of alternative fuels: Sasol fully synthetic jet fuel (FSJF), Shell gas-to-liquid (GTL) kerosene, and Jet A-1/GTL 50:50 blended kerosene. The concentration of PAH compounds in the exhaust emissions vary greatly between fuels. Combustion of FSJF produces the greatest total concentration of PAH compounds while combustion of GTL produces the least. However, when PAHs in the exhaust sample are measured in terms of the regulatory marker compound benzo[a]pyrene, then all of the alternative fuels emit a lower concentration of PAH in comparison to Jet A-1. Emissions from the combustion of Jet A-1/GTL blended kerosene were found to have a disproportionately low concentration of PAHs and appear to inherit a greater proportion of the GTL emission characteristics than would be expected from volume fraction alone. The data imply the presence of a nonlinear relation between fuel blend composition and the emission of PAH compounds. For each of the fuels, the speciation of PAH compounds present in the exhaust emissions were found to be remarkably similar (R(2) = 0.94-0.62), and the results do provide evidence to support the premise that PAH speciation is to some extent indicative of the emission source. In contrast, no correlation was found between the PAH species present in the fuel with those subsequently emitted in the exhaust. The results strongly suggests that local air quality measured in terms of the particulate-bound PAH burden could be significantly improved by the use of GTL kerosene either blended with or in place of Jet A-1 kerosene.

Comparison of emissions and toxicological properties of fine particles from wood and oil boilers in small (20-25 kW) and medium (5-10 MW) scale

NASA Astrophysics Data System (ADS)

Kaivosoja, T.; Jalava, P. I.; Lamberg, H.; Virén, A.; Tapanainen, M.; Torvela, T.; Tapper, U.; Sippula, O.; Tissari, J.; Hillamo, R.; Hirvonen, M.-R.; Jokiniemi, J.

2013-10-01

The aim of this study was to compare four alternatives for providing decentralized energy production in small communities in terms of their flue gas emissions and toxicological properties of the emissions. In this study, two different size classes of boilers were examined and the use of fossil fuel oils was compared against wood fuels. The lowest PM1 emission, 0.1 mg MJ-1, was observed from small-scale light fuel oil combustion. In medium-scale wood combustion, PM1 emission values from a grate fired wood combustion boiler (10 MW) without particulate filtration were the highest (264 mg MJ-1) but were substantially reduced down to 0.6 mg MJ-1 due to the usage of an electrostatic precipitator (ESP). The wood combustion particles were mainly formed of potassium salts. In light fuel oil combustion, one of the main components in the particles was sulphate whereas in heavy fuel oil combustion also significant amounts of V and Ni were emitted. Pellet combustion produced the lowest PAH emissions. Overall, oil combustion produced higher amount of PAHs than wood combustion. This was indicated also as a higher cytotoxicity of the oil combustion samples when compared to those from wood combustion in the corresponding scale of boilers. However, when calculated on an equal mass basis, the particles collected after ESP were even more cytotoxic which can be explained by the altered chemical characteristics of the emissions in the ESP. Due to the variation in the emissions and in the toxicity of the emissions, we propose that in the long term, not only the emission levels but also the toxicity of the emissions should be taken into account in the regulations of the emission limits of the combustion plants.

Elemental characterization and source apportionment of PM10 and PM2.5 in the western coastal area of central Taiwan.

PubMed

Hsu, Chin-Yu; Chiang, Hung-Che; Lin, Sheng-Lun; Chen, Mu-Jean; Lin, Tzu-Yu; Chen, Yu-Cheng

2016-01-15

This study investigated seasonal variations in PM10 and PM2.5 mass and associated trace metal concentrations in a residential area in proximity to the crude oil refinery plants and industrial parks of central Taiwan. Particle measurements were conducted during winter, spring and summer in 2013 and 2014. Twenty-six trace metals in PM10 and PM2.5 were analyzed using ICP-MS. Multiple approaches of the backward trajectory model, enrichment factor (EF), Lanthanum enrichment and positive matrix fraction (PMF) were used to identify potential sources of particulate metals. Mean concentrations of PM10 in winter, spring and summer were 76.4 ± 22.6, 33.2 ± 9.9 and 37.4 ± 17.0 μg m(-3), respectively, while mean levels of PM2.5 in winter, spring and summer were 47.8 ± 20.0, 23.9 ± 11.2 and 16.3 ± 8.2 μg m(-3), respectively. The concentrations of carcinogenic metals (Ni, As and adjusted Cr(VI)) in PM10 and PM2.5 exceeded the guideline limits published by WHO. The result of EF analysis confirmed that Mo, Sb, Cd, Zn, Mg, Cr, As, Pb, Cu, Ni and V were attributable to anthropogenic emission. PMF analysis demonstrated that trace metals in PM10 and PM2.5 were from the similar sources, such as coal combustion, oil combustion and traffic-related emission, except for soil dust and crustal element emissions only observed in PM10 and secondary aluminum smelter only observed in PM2.5. Considering health-related particulate metals, the traffic-related emission and coal combustion for PM10 and PM2.5, respectively, are important to control for reducing potential carcinogenic risk. The results could aid efforts to clarify the impact of source-specific origins on human health. Copyright © 2015 Elsevier B.V. All rights reserved.

Air pollution source apportionment before, during, and after the 2008 Beijing Olympics and association of sources to aldehydes and biomarkers of blood coagulation, pulmonary and systemic inflammation, and oxidative stress in healthy young adults

NASA Astrophysics Data System (ADS)

Altemose, Brent A.

Based on principal component analysis (PCA) of air pollution data collected during the Summer Olympic Games held in Beijing, China during 2008, the five source types of air pollution identified -- natural soil/road dust, vehicle and industrial combustion, vegetative burning, oil combustion, and secondary formation, were all distinctly lower during the Olympics. This was particularly true for vehicle and industrial combustion and oil combustion, and during the main games period between the opening and closing ceremonies. The reduction in secondary formation was reflective of a reduction in nitrogen oxides, but this also contributed to increased ozone concentrations during the Olympic period. Among three toxic aldehydes measured in Beijing during the same time period, only acetaldehyde had a reduction in mean concentration during the Olympic air pollution control period compared to the pre-Olympic period. Accordingly, acetaldehyde was significantly correlated with primary emission sources including vegetative burning and oil combustion, and with several pollutants emitted mainly from primary sources. In contrast, formaldehyde and acrolein increased during the Olympic air pollution control period; accordingly both were significantly correlated with ozone and with the secondary formation source type. These findings indicate primary sources may dominate for acetaldehyde while secondary sources may dominate for formaldehyde and acrolein. Biomarkers for pulmonary inflammation (exhaled breath condensate (EBC) pH, exhaled nitric oxide, and EBC nitrite) and hemostasis and blood coagulation (vWF and sCD62p) were most consistently associated with vehicle and industrial combustion, oil combustion, and vegetative burning. The systemic inflammation biomarker 8-OHdG was most consistently associated with vehicle and industrial combustion. In contrast, the associations between the biomarkers and the aldehydes were generally not significant or in the hypothesized direction, although EBC nitrite was associated with both acrolein and acetaldehyde, and sCD62p was associated with acetaldehyde. Notably, the biomarker sCD40L showed few significant associations with any of the air pollution source types or aldehydes. The findings indicate that implementing controls for combustion sources may have a positive impact on cardiorespiratory health, even in healthy young adults. More aggressive control of vegetative burning and further reduction of nitrogen oxide concentrations would likely have an even more positive impact.

Sources of particulate matter in China: Insights from source apportionment studies published in 1987-2017.

PubMed

Zhu, Yanhong; Huang, Lin; Li, Jingyi; Ying, Qi; Zhang, Hongliang; Liu, Xingang; Liao, Hong; Li, Nan; Liu, Zhenxin; Mao, Yuhao; Fang, Hao; Hu, Jianlin

2018-06-01

Particulate matter (PM) in the atmosphere has adverse effects on human health, ecosystems, and visibility. It also plays an important role in meteorology and climate change. A good understanding of its sources is essential for effective emission controls to reduce PM and to protect public health. In this study, a total of 239 PM source apportionment studies in China published during 1987-2017 were reviewed. The documents studied include peer-reviewed papers in international and Chinese journals, as well as degree dissertations. The methods applied in these studies were summarized and the main sources in various regions of China were identified. The trends of source contributions at two major cities with abundant studies over long-time periods were analyzed. The most frequently used methods for PM source apportionment in China are receptor models, including chemical mass balance (CMB), positive matrix factorization (PMF), and principle component analysis (PCA). Dust, fossil fuel combustion, transportation, biomass burning, industrial emission, secondary inorganic aerosol (SIA) and secondary organic aerosol (SOA) are the main source categories of fine PM identified in China. Even though the sources of PM vary among seven different geographical areas of China, SIA, industrial, and dust emissions are generally found to be the top three source categories in 2007-2016. A number of studies investigated the sources of SIA and SOA in China using air quality models and indicated that fossil fuel combustion and industrial emissions were the most important sources of SIA (total contributing 63.5%-88.1% of SO 4 2- , and 47.3%-70% NO 3 - ), and agriculture emissions were the dominant source of NH 4 + (contributing 53.9%-90%). Biogenic emissions were the most important source of SOA in China in summer, while residential and industrial emissions were important in winter. Long-term changes of PM sources at two megacities of Beijing and Nanjing indicated that the contributions of fossil fuel and industrial sources have been declining after stricter emission controls in recent years. In general, dust and industrial contributions decreased and transportation contributions increased after 2000. PM 2.5 emissions are predicted to decline in most regions during 2005-2030, even though the energy consumptions except biomass burning are predicted to continue to increase. Industrial, residential, and biomass burning sources will become more important in the future in the businuess-as-usual senarios. This review provides valuable information about main sources of PM and their trends in China. A few recommendations are suggested to further improve our understanding the sources and to develop effective PM control strategies in various regions of China. Copyright © 2018 Elsevier Ltd. All rights reserved.

Source identification and apportionment of heavy metals in urban soil profiles.

PubMed

Luo, Xiao-San; Xue, Yan; Wang, Yan-Ling; Cang, Long; Xu, Bo; Ding, Jing

2015-05-01

Because heavy metals (HMs) occurring naturally in soils accumulate continuously due to human activities, identifying and apportioning their sources becomes a challenging task for pollution prevention in urban environments. Besides the enrichment factors (EFs) and principal component analysis (PCA) for source classification, the receptor model (Absolute Principal Component Scores-Multiple Linear Regression, APCS-MLR) and Pb isotopic mixing model were also developed to quantify the source contribution for typical HMs (Cd, Co, Cr, Cu, Mn, Ni, Pb, Zn) in urban park soils of Xiamen, a representative megacity in southeast China. Furthermore, distribution patterns of their concentrations and sources in 13 soil profiles (top 20 cm) were investigated by different depths (0-5, 5-10, 10-20 cm). Currently the principal anthropogenic source for HMs in urban soil of China is atmospheric deposition from coal combustion rather than vehicle exhaust. Specifically for Pb source by isotopic model ((206)Pb/(207)Pb and (208)Pb/(207)Pb), the average contributions were natural (49%)>coal combustion (45%)≫traffic emissions (6%). Although the urban surface soils are usually more contaminated owing to recent and current human sources, leaching effects and historic vehicle emissions can also make deep soil layer contaminated by HMs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Provisional Guidance for Quantitative Risk Assessment of Polycyclic Aromatic Hydrocarbons

EPA Science Inventory

Polycyclic Aromatic Hydrocarbons (PAHs) are products of incomplete combustion of organic materials; sources are, thus, widespread,including cigarette smoke, municipal waste incineration, wood stove emissions, coal conversion, energy production form fossil fuels, and automobile an...

40 CFR 98.30 - Definition of the source category.

Code of Federal Regulations, 2010 CFR

2010-07-01

... generators and emergency equipment, as defined in § 98.6. (3) Irrigation pumps at agricultural operations. (4... a unit that combusts hazardous waste (as defined in 40 CFR 261.3), reporting of GHG emissions is not...

40 CFR 98.262 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each... GREENHOUSE GAS REPORTING Phosphoric Acid Production § 98.262 GHGs to report. (a) You must report CO2 process...

40 CFR 98.262 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each... GREENHOUSE GAS REPORTING Phosphoric Acid Production § 98.262 GHGs to report. (a) You must report CO2 process...

40 CFR 98.262 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each... GREENHOUSE GAS REPORTING Phosphoric Acid Production § 98.262 GHGs to report. (a) You must report CO2 process...

40 CFR 98.262 - GHGs to report.

Code of Federal Regulations, 2010 CFR

2010-07-01

... part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each... GREENHOUSE GAS REPORTING Phosphoric Acid Production § 98.262 GHGs to report. (a) You must report CO2 process...

40 CFR 98.262 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... part (General Stationary Fuel Combustion Sources) the emissions of CO2, CH4, and N2O from each... GREENHOUSE GAS REPORTING Phosphoric Acid Production § 98.262 GHGs to report. (a) You must report CO2 process...

The impact of municipal waste combustion in small heat sources

NASA Astrophysics Data System (ADS)

Vantúch, Martin; Kaduchová, Katarína; Lenhard, Richard

2016-06-01

At present there is a tendency to make greater use for heating houses for burning solid fuel, such as pieces of wood, coal, coke, local sources of heat to burn natural gas. This tendency is given both the high price of natural gas as well as the availability of cheaper solid fuel. In many cases, in the context saving heating costs, respectively in the context of the disposal of waste is co-incinerated with municipal solid fuels and wastes of different composition. This co entails increased production emissions such as CO (carbon monoxide), NOx (nitrogen oxides), particulate matter (particulate matter), PM10, HCl (hydrogen chloride), PCDD/F (polychlorinated dibenzodioxins and dibenzofurans), PCBs (polychlorinated biphenyls) and others. The experiment was focused on the emission factors from the combustion of fossil fuels in combination with municipal waste in conventional boilers designed to burn solid fuel.

Nitrogen enriched combustion of a natural gas internal combustion engine to reduce NO.sub.x emissions

DOEpatents

Biruduganti, Munidhar S.; Gupta, Sreenath Borra; Sekar, R. Raj; McConnell, Steven S.

2008-11-25

A method and system for reducing nitrous oxide emissions from an internal combustion engine. An input gas stream of natural gas includes a nitrogen gas enrichment which reduces nitrous oxide emissions. In addition ignition timing for gas combustion is advanced to improve FCE while maintaining lower nitrous oxide emissions.

The mortality cost of particulate matter due to emissions in the Stockholm area : an investigation into harmfulness, sources and the geographical dimension of their impact

DOT National Transportation Integrated Search

2008-12-01

The findings in this report are that there is not an one-to-one correspondence between emissions and costs. The reason for this is that the cost is based on health impacts which in turn are related to population exposure. Combustion particulate matte...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carrington, David Bradley; Waters, Jiajia

Research and development of KIVA-hpFE for turbulent reactive and multiphase flow particularly as related to engine modeling program has relevance to National energy security and climate change. Climate change is a source problem, and energy national security is consumption of petroleum products problem. Accurately predicting engine processes leads to, lower greenhouse gas (GHG) emission, where engines in the transportation sector currently account for 26% of the U.S. GHG emissions. Less dependence on petroleum products leads to greater energy security. By Environmental Protection Agency standards, some vehicles are now reaching 42 to the 50 mpg mark. These are conventional gasoline engines.more » Continued investment and research into new technical innovations, the potential exists to save more than 4 million barrels of oil per day or approximately $200 to $400 million per day. This would be a significant decrease in emission and use of petroleum and a very large economic stimulus too! It is estimated with further advancements in combustion, the current emissions can be reduced up to 40%. Enabling better understanding of fuel injection and fuel-air mixing, thermodynamic combustion losses, and combustion/emission formation processes enhances our ability to help solve both problems. To provide adequate capability for accurately simulating these processes, minimize time and labor for development of engine technology, are the goals of our KIVA development program.« less

A paler shade of green? The toxicology of biodiesel emissions ...

EPA Pesticide Factsheets

Background: Biodiesel produced primarily from plants and algal feedstocks is believed to have advantages for production and use compared to petroleum and to some other fuel sources. There is some speculation that exposure to biodiesel combustion emissions may not induce biological responses or health effects or at a minimum reduce the effects relative to other fuels. In evaluating the overall environmental and health effects of biodiesel production to end use scenario, empirical data or modeling data based on such data are needed.Scope of Review: This manuscript examines the available toxicology reports examining combustion derived biodiesel emissions since approximately 2007, when our last review of the topic occurred. Toxicity derived from other end uses of biodiesel- eg, spills, dermal absorption, etc- are not examined. Findings from biodiesel emissions are roughly divided into three areas: whole non-human animal model exposures; in vitro exposures of mammalian and bacterial cells (used for mutation studies primarily); and human exposures in controlled or other exposure fashions. Major Conclusions: Overall, these more current studies clearly demonstrate that biodiesel combustion emission exposure- to either 100% biodiesel or a blend in petroleum diesel- can induce biological effects. There are reports that show biodiesel exposure generally induces more effects or a greater magnitude of effect than petroleum diesel, however there are also a similar number

Analysis of polycyclic aromatic hydrocarbons in tree-rings of Masson pine (Pinus massoniana L.) from two industrial sites in the Pearl River Delta, south China.

PubMed

Kuang, Yuan-wen; Zhou, Guo-yi; Wen, Da-zhi; Li, Jiong; Sun, Fang-fang

2011-09-01

Concentrations of polycyclic aromatic hydrocarbons (PAHs) were examined and potential sources of PAHs were identified from the dated tree-rings of Masson pine (Pinus massoniana L.) near two industrial sites (Danshuikeng, DSK and Xiqiaoshan, XQS) in the Pearl River Delta of south China. Total concentrations of PAHs (∑PAHs) were revealed with similar patterns of temporal trends in the tree-rings at both sites, suggesting tree-rings recorded the historical variation in atmospheric PAHs. The differences of individual PAHs and of ∑PAHs detected in the tree-rings between the two sites reflected the historical differences of airborne PAHs. Regional changes in industrial activities might contribute to the site-specific and period-specific patterns of the tree-ring PAHs. The diagnostic PAH ratios of Ant/(Ant + PA), FL/(FL + Pyr), and BaA/(BaA + Chr)) revealed that PAHs in the tree-rings at both sites mainly stemmed from the combustion process (pyrogenic sources). Principal component analysis further confirmed that wood burning, coal combustion, diesel, and gasoline-powered vehicular emissions were the dominant contributors of PAHs sources at DSK, while diesel combustion, gasoline and natural gas combustion, and incomplete coal combustion were responsible for the main origins of PAHs at XQS. Tree-ring analysis of PAHs was indicative of PAHs from a mixture of sources of combustion, thus minimizing the bias of short-term active air sampling.

Emissions from open burning of simulated military waste from forward operating bases.

PubMed

Aurell, Johanna; Gullett, Brian K; Yamamoto, Dirk

2012-10-16

Emissions from open burning of simulated military waste from forward operating bases (FOBs) were extensively characterized as an initial step in assessing potential inhalation exposure of FOB personnel and future disposal alternatives. Emissions from two different burning scenarios, so-called "burn piles/pits" and an air curtain burner/"burn box", were compared using simulated FOB waste from municipal and commercial sources. A comprehensive array of emissions was quantified, including CO(2), PM(2.5), volatile organic compounds (VOCs), polyaromatic hydrocarbons (PAHs), polychlorinated dibenzodioxins and -furans (PCDDs/PCDFs), polybrominated dibenzodioxins and -furans (PBDDs/PBDFs), and metals. In general, smoldering conditions in the burn box and the burn pile led to similar emissions. However, when the burn box underwent periodic waste charging to maintain sustained combustion, PM(2.5), VOCs, and PAH emissions dropped considerably compared to smoldering conditions and the overall burn pile results. The PCDD/PCDF and PBDD/PBDF emission factors for the burn piles were 50 times higher than those from the burn box likely due to the dominance of smoldering combustion in the burn piles.

Atmospheric polycyclic aromatic hydrocarbons in the urban environment: Occurrence, toxicity and source apportionment.

PubMed

Mishra, Nitika; Ayoko, Godwin A; Morawska, Lidia

2016-01-01

Polycyclic Aromatic Hydrocarbons (PAHs) represent a major class of toxic pollutants because of their carcinogenic and mutagenic characteristics. People living in urban areas are regularly exposed to PAHs because of abundance of their emission sources. Within this context, this study aimed to: (i) identify and quantify the levels of ambient PAHs in an urban environment; (ii) evaluate their toxicity; and (iii) identify their sources as well as the contribution of specific sources to measured concentrations. Sixteen PAHs were identified and quantified in air samples collected from Brisbane. Principal Component Analysis - Absolute Principal Component Scores (PCA-APCS) was used in order to conduct source apportionment of the measured PAHs. Vehicular emissions, natural gas combustion, petrol emissions and evaporative/unburned fuel were the sources identified; contributing 56%, 21%, 15% and 8% of the total PAHs emissions, respectively, all of which need to be considered for any pollution control measures implemented in urban areas. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of diluted and preheated oxidizer on the emission of methane flameless combustion

NASA Astrophysics Data System (ADS)

Hosseini, Seyed Ehsan; Salehirad, Saber; Wahid, M. A.; Sies, Mohsin Mohd; Saat, Aminuddin

2012-06-01

In combustion process, reduction of emissions often accompanies with output efficiency reduction. It means, by using current combustion technique it is difficult to obtainlow pollution and high level of efficiency in the same time. In new combustion system, low NOxengines and burners are studied particularly. Recently flameless or Moderate and Intensive Low oxygen Dilution (MILD) combustion has received special attention in terms of low harmful emissions and low energy consumption. Behavior of combustion with highly preheated air was analyzed to study the change of combustion regime and the reason for the compatibility of high performance and low NOx production. Sustainability of combustion under low oxygen concentration was examined when; the combustion air temperature was above the self-ignition temperature of the fuel. This paper purposes to analyze the NOx emission quantity in conventional combustion and flameless combustion by Chemical Equilibrium with Applications (CEA) software.

Lead contamination and source in Shanghai in the past century using dated sediment cores from urban park lakes.

PubMed

Li, H B; Yu, S; Li, G L; Deng, H

2012-08-01

Lead contamination becomes of importance to urban resident health worldwide, especially for child health and growth. Undisturbed lake sediment cores are increasingly employed as a useful tool to backdate environmental contamination history. Five intact sediment cores collected from lakes in five urban parks were dated using (210)Pb and analyzed for total Pb content and isotope ratio to reconstruct the Pb contamination history over the last century in Shanghai, China. Total Pb content in the sediment cores increased by about 2- to 3-fold since 1900s. The profile of Pb flux in each sediment core revealed a remarkable increase of Pb contamination in Shanghai over the past century, especially in the latest three decades when China was experiencing a rapid economic and industrial development. Significant correlations were found between Pb fluxes in sediment cores and Pb emission from coal combustion in Shanghai. Coal combustion emission dominated anthropogenic Pb sources during the past century contributing from 52% to 69% of total Pb in cores, estimated by a three-end member model of Pb isotope ratios. Leaded gasoline emission generally contributed <30% of total Pb, which was banned by 1997 in the Shanghai region. Our results implicate that coal combustion-based energy consumption should be replaced, or at least partially replaced, to reduce health risks of Pb contamination in Shanghai. Copyright © 2012 Elsevier Ltd. All rights reserved.

Fossil vs. non-fossil sources of fine carbonaceous aerosols in four Chinese cities during the extreme winter haze episode of 2013

NASA Astrophysics Data System (ADS)

Zhang, Y.-L.; Huang, R.-J.; El Haddad, I.; Ho, K.-F.; Cao, J.-J.; Han, Y.; Zotter, P.; Bozzetti, C.; Daellenbach, K. R.; Canonaco, F.; Slowik, J. G.; Salazar, G.; Schwikowski, M.; Schnelle-Kreis, J.; Abbaszade, G.; Zimmermann, R.; Baltensperger, U.; Prévôt, A. S. H.; Szidat, S.

2015-02-01

During winter 2013, extremely high concentrations (i.e., 4-20 times higher than the World Health Organization guideline) of PM2.5 (particulate matter with an aerodynamic diameter < 2.5 μm) mass concentrations (24 h samples) were found in four major cities in China including Xi'an, Beijing, Shanghai and Guangzhou. Statistical analysis of a combined data set from elemental carbon (EC), organic carbon (OC), 14C and biomass-burning marker measurements using Latin hypercube sampling allowed a quantitative source apportionment of carbonaceous aerosols. Based on 14C measurements of EC fractions (six samples each city), we found that fossil emissions from coal combustion and vehicle exhaust dominated EC with a mean contribution of 75 ± 8% across all sites. The remaining 25 ± 8% was exclusively attributed to biomass combustion, consistent with the measurements of biomass-burning markers such as anhydrosugars (levoglucosan and mannosan) and water-soluble potassium (K+). With a combination of the levoglucosan-to-mannosan and levoglucosan-to-K+ ratios, the major source of biomass burning in winter in China is suggested to be combustion of crop residues. The contribution of fossil sources to OC was highest in Beijing (58 ± 5%) and decreased from Shanghai (49 ± 2%) to Xi'an (38 ± 3%) and Guangzhou (35 ± 7%). Generally, a larger fraction of fossil OC was from secondary origins than primary sources for all sites. Non-fossil sources accounted on average for 55 ± 10 and 48 ± 9% of OC and total carbon (TC), respectively, which suggests that non-fossil emissions were very important contributors of urban carbonaceous aerosols in China. The primary biomass-burning emissions accounted for 40 ± 8, 48 ± 18, 53 ± 4 and 65 ± 26% of non-fossil OC for Xi'an, Beijing, Shanghai and Guangzhou, respectively. Other non-fossil sources excluding primary biomass burning were mainly attributed to formation of secondary organic carbon (SOC) from non-fossil precursors such as biomass-burning emissions. For each site, we also compared samples from moderately to heavily polluted days according to particulate matter mass. Despite a significant increase of the absolute mass concentrations of primary emissions from both fossil and non-fossil sources during the heavily polluted events, their relative contribution to TC was even decreased, whereas the portion of SOC was consistently increased at all sites. This observation indicates that SOC was an important fraction in the increment of carbonaceous aerosols during the haze episode in China.

Solubility of iron from combustion source particles in acidic media linked to iron speciation.

PubMed

Fu, Hongbo; Lin, Jun; Shang, Guangfeng; Dong, Wenbo; Grassian, Vichi H; Carmichael, Gregory R; Li, Yan; Chen, Jianmin

2012-10-16

In this study, iron solubility from six combustion source particles was investigated in acidic media. For comparison, a Chinese loess (CL) dust was also included. The solubility experiments confirmed that iron solubility was highly variable and dependent on particle sources. Under dark and light conditions, the combustion source particles dissolved faster and to a greater extent relative to CL. Oil fly ash (FA) yielded the highest soluble iron as compared to the other samples. Total iron solubility fractions measured in the dark after 12 h ranged between 2.9 and 74.1% of the initial iron content for the combustion-derived particles (Oil FA > biomass burning particles (BP) > coal FA). Ferrous iron represented the dominant soluble form of Fe in the suspensions of straw BP and corn BP, while total dissolved Fe presented mainly as ferric iron in the cases of oil FA, coal FA, and CL. Mössbauer measurements and TEM analysis revealed that Fe in oil FA was commonly presented as nanosized Fe(3)O(4) aggregates and Fe/S-rich particles. Highly labile source of Fe in corn BP could be originated from amorphous Fe form mixed internally with K-rich particles. However, Fe in coal FA was dominated by the more insoluble forms of both Fe-bearing aluminosilicate glass and Fe oxides. The data presented herein showed that iron speciation varies by source and is an important factor controlling iron solubility from these anthropogenic emissions in acidic solutions, suggesting that the variability of iron solubility from combustion-derived particles is related to the inherent character and origin of the aerosols themselves. Such information can be useful in improving our understanding on iron solubility from combustion aerosols when they undergo acidic processing during atmospheric transport.

Source apportionment of the carcinogenic potential of polycyclic aromatic hydrocarbons (PAH) associated to airborne PM10 by a PMF model.

PubMed

Callén, M S; Iturmendi, A; López, J M; Mastral, A M

2014-02-01

In order to perform a study of the carcinogenic potential of polycyclic aromatic hydrocarbons (PAH), benzo(a)pyrene equivalent (BaP-eq) concentration was calculated and modelled by a receptor model based on positive matrix factorization (PMF). Nineteen PAH associated to airborne PM10 of Zaragoza, Spain, were quantified during the sampling period 2001-2009 and used as potential variables by the PMF model. Afterwards, multiple linear regression analysis was used to quantify the potential sources of BaP-eq. Five sources were obtained as the optimal solution and vehicular emission was identified as the main carcinogenic source (35 %) followed by heavy-duty vehicles (28 %), light-oil combustion (18 %), natural gas (10 %) and coal combustion (9 %). Two of the most prevailing directions contributing to this carcinogenic character were the NE and N directions associated with a highway, industrial parks and a paper factory. The lifetime lung cancer risk exceeded the unit risk of 8.7 x 10(-5) per ng/m(3) BaP in both winter and autumn seasons and the most contributing source was the vehicular emission factor becoming an important issue in control strategies.

Criteria pollutant and greenhouse gas emissions from CNG transit buses equipped with three-way catalysts compared to lean-burn engines and oxidation catalyst technologies.

PubMed

Yoon, Seungju; Collins, John; Thiruvengadam, Arvind; Gautam, Mridul; Herner, Jorn; Ayala, Alberto

2013-08-01

Engine and exhaust control technologies applied to compressed natural gas (CNG) transit buses have advanced from lean-burn, to lean-burn with oxidation catalyst (OxC), to stoichiometric combustion with three-way catalyst (TWC). With this technology advancement, regulated gaseous and particulate matter emissions have been significantly reduced. Two CNG transit buses equipped with stoichiometric combustion engines and TWCs were tested on a chassis dynamometer, and their emissions were measured. Emissions from the stoichiometric engines with TWCs were then compared to the emissions from lean-burn CNG transit buses tested in previous studies. Stoichiometric combustion with TWC was effective in reducing emissions of oxides of nitrogen (NO(x)), particulate matter (PM), and nonmethane hydrocarbon (NMHC) by 87% to 98% depending on pollutants and test cycles, compared to lean combustion. The high removal efficiencies exceeded the emission reduction required from the certification standards, especially for NO(x) and PM. While the certification standards require 95% and 90% reductions for NO(x) and PM, respectively, from the engine model years 1998-2003 to the engine model year 2007, the measured NO(x) and PM emissions show 96% and 95% reductions, respectively, from the lean-burn engines to the stoichiometric engines with TWC over the transient Urban Dynamometer Driving Schedule (UDDS) cycle. One drawback of stoichiometric combustion with TWC is that this technology produces higher carbon monoxide (CO) emissions than lean combustion. In regard to controlling CO emissions, lean combustion with OxC is more effective than stoichiometric combustion. Stoichiometric combustion with TWC produced higher greenhouse gas (GHG) emissions including carbon dioxide (CO2) and methane (CH4) than lean combustion during the UDDS cycle, but lower GHG emissions during the steady-state cruise cycle. Stoichiometric combustion with three-way catalyst is currently the best emission control technology available for compressed natural gas (CNG) transit buses to meet the stringent U.S. Environmental Protection Agency (EPA) 2010 heavy-duty engine NO(x) emissions standard. For existing lean-burn CNG transit buses in the fleet, oxidation catalyst would be the most effective retrofit technology for the control of NMHC and CO emissions.

40 CFR 60.4203 - How long must my engines meet the emission standards if I am a stationary CI internal combustion...

Code of Federal Regulations, 2010 CFR

2010-07-01

... emission standards if I am a stationary CI internal combustion engine manufacturer? 60.4203 Section 60.4203... Combustion Engines Emission Standards for Manufacturers § 60.4203 How long must my engines meet the emission standards if I am a stationary CI internal combustion engine manufacturer? Engines manufactured by...

40 CFR 60.4203 - How long must my engines meet the emission standards if I am a stationary CI internal combustion...

Code of Federal Regulations, 2011 CFR

2011-07-01

... emission standards if I am a stationary CI internal combustion engine manufacturer? 60.4203 Section 60.4203... Combustion Engines Emission Standards for Manufacturers § 60.4203 How long must my engines meet the emission standards if I am a stationary CI internal combustion engine manufacturer? Engines manufactured by...

Dioxins and polyvinylchloride in combustion and fires.

PubMed

Zhang, Mengmei; Buekens, Alfons; Jiang, Xuguang; Li, Xiaodong

2015-07-01

This review on polyvinylchloride (PVC) and dioxins collects, collates, and compares data from selected sources on the formation of polychlorinated dibenzofurans (PCDFs) and dibenzo-p-dioxins (PCDDs), or in brief dioxins, in combustion and fires. In professional spheres, the incineration of PVC as part of municipal solid waste is seldom seen as a problem, since deep flue gas cleaning is required anyhow. Conversely, with its high content of chlorine, PVC is frequently branded as a major chlorine donor and spitefully leads to substantial formation of dioxins during poorly controlled or uncontrolled combustion and open fires. Numerous still ill-documented and diverse factors of influence may affect the formation of dioxins during combustion: on the one hand PVC-compounds represent an array of materials with widely different formulations; on the other hand these may all be exposed to fires of different nature and consequences. Hence, attention should be paid to PVC with respect to the ignition and development of fires, as well as attenuating the emission of objectionable compounds, such as carbon monoxide, hydrogen chloride, polycyclic aromatic hydrocarbons, and dioxins. This review summarises available dioxin emissions data, gathers experimental and simulation studies of fires and combustion tests involving PVC, and identifies and analyses the effects of several local factors of influence, affecting the formation of dioxins during PVC combustion. © The Author(s) 2015.

Chemical compositions and source identification of PM₂.₅ aerosols for estimation of a diesel source surrogate.

PubMed

Sahu, Manoranjan; Hu, Shaohua; Ryan, Patrick H; Le Masters, Grace; Grinshpun, Sergey A; Chow, Judith C; Biswas, Pratim

2011-06-01

Exposure to traffic-related pollution during childhood has been associated with asthma exacerbation, and asthma incidence. The objective of the Cincinnati Childhood Allergy and Air Pollution Study (CCAAPS) is to determine if the development of allergic and respiratory disease is associated with exposure to diesel engine exhaust particles. A detailed receptor model analyses was undertaken by applying positive matrix factorization (PMF) and UNMIX receptor models to two PM₂.₅ data sets: one consisting of two carbon fractions and the other of eight temperature-resolved carbon fractions. Based on the source profiles resolved from the analyses, markers of traffic-related air pollution were estimated: the elemental carbon attributed to traffic (ECAT) and elemental carbon attributed to diesel vehicle emission (ECAD). Application of UNMIX to the two data sets generated four source factors: combustion related sulfate, traffic, metal processing and soil/crustal. The PMF application generated six source factors derived from analyzing two carbon fractions and seven factors from temperature-resolved eight carbon fractions. The source factors (with source contribution estimates by mass concentrations in parentheses) are: combustion sulfate (46.8%), vegetative burning (15.8%), secondary sulfate (12.9%), diesel vehicle emission (10.9%), metal processing (7.5%), gasoline vehicle emission (5.6%) and soil/crustal (0.7%). Diesel and gasoline vehicle emission sources were separated using eight temperature-resolved organic and elemental carbon fractions. Application of PMF to both datasets also differentiated the sulfate rich source from the vegetative burning source, which are combined in a single factor by UNMIX modeling. Calculated ECAT and ECAD values at different locations indicated that traffic source impacts depend on factors such as traffic volumes, meteorological parameters, and the mode of vehicle operation apart from the proximity of the sites to highways. The difference in ECAT and ECAD, however, was less than one standard deviation. Thus, a cost benefit consideration should be used when deciding on the benefits of an eight or two carbon approach. Published by Elsevier B.V.

Characterization of gas-phase organics using proton transfer reaction time-of-flight mass spectrometry: fresh and aged residential wood combustion emissions

NASA Astrophysics Data System (ADS)

Bruns, Emily A.; Slowik, Jay G.; El Haddad, Imad; Kilic, Dogushan; Klein, Felix; Dommen, Josef; Temime-Roussel, Brice; Marchand, Nicolas; Baltensperger, Urs; Prévôt, André S. H.

2017-01-01

Organic gases emitted during the flaming phase of residential wood combustion are characterized individually and by functionality using proton transfer reaction time-of-flight mass spectrometry. The evolution of the organic gases is monitored during photochemical aging. Primary gaseous emissions are dominated by oxygenated species (e.g., acetic acid, acetaldehyde, phenol and methanol), many of which have deleterious health effects and play an important role in atmospheric processes such as secondary organic aerosol formation and ozone production. Residential wood combustion emissions differ considerably from open biomass burning in both absolute magnitude and relative composition. Ratios of acetonitrile, a potential biomass burning marker, to CO are considerably lower ( ˜ 0.09 pptv ppbv-1) than those observed in air masses influenced by open burning ( ˜ 1-2 pptv ppbv-1), which may make differentiation from background levels difficult, even in regions heavily impacted by residential wood burning. A considerable amount of formic acid forms during aging ( ˜ 200-600 mg kg-1 at an OH exposure of (4.5-5.5) × 107 molec cm-3 h), indicating residential wood combustion can be an important local source for this acid, the quantities of which are currently underestimated in models. Phthalic anhydride, a naphthalene oxidation product, is also formed in considerable quantities with aging ( ˜ 55-75 mg kg-1 at an OH exposure of (4.5-5.5) × 107 molec cm-3 h). Although total NMOG emissions vary by up to a factor of ˜ 9 between burns, SOA formation potential does not scale with total NMOG emissions and is similar in all experiments. This study is the first thorough characterization of both primary and aged organic gases from residential wood combustion and provides a benchmark for comparison of emissions generated under different burn parameters.

Optical and chemical characterization of aerosols emitted from coal, heavy and light fuel oil, and small-scale wood combustion.

PubMed

Frey, Anna K; Saarnio, Karri; Lamberg, Heikki; Mylläri, Fanni; Karjalainen, Panu; Teinilä, Kimmo; Carbone, Samara; Tissari, Jarkko; Niemelä, Ville; Häyrinen, Anna; Rautiainen, Jani; Kytömäki, Jorma; Artaxo, Paulo; Virkkula, Aki; Pirjola, Liisa; Rönkkö, Topi; Keskinen, Jorma; Jokiniemi, Jorma; Hillamo, Risto

2014-01-01

Particle emissions affect radiative forcing in the atmosphere. Therefore, it is essential to know the physical and chemical characteristics of them. This work studied the chemical, physical, and optical characteristics of particle emissions from small-scale wood combustion, coal combustion of a heating and power plant, as well as heavy and light fuel oil combustion at a district heating station. Fine particle (PM1) emissions were the highest in wood combustion with a high fraction of absorbing material. The emissions were lowest from coal combustion mostly because of efficient cleaning techniques used at the power plant. The chemical composition of aerosols from coal and oil combustion included mostly ions and trace elements with a rather low fraction of absorbing material. The single scattering albedo and aerosol forcing efficiency showed that primary particles emitted from wood combustion and some cases of oil combustion would have a clear climate warming effect even over dark earth surfaces. Instead, coal combustion particle emissions had a cooling effect. Secondary processes in the atmosphere will further change the radiative properties of these emissions but are not considered in this study.