Prospective, randomized, blinded evaluation of donor semen quality provided by seven commercial sperm banks.

PubMed

Carrell, Douglas T; Cartmill, Deborah; Jones, Kirtly P; Hatasaka, Harry H; Peterson, C Matthew

2002-07-01

To evaluate variability in donor semen quality between seven commercial donor sperm banks, within sperm banks, and between intracervical insemination and intrauterine insemination. Prospective, randomized, blind evaluation of commercially available donor semen samples. An academic andrology laboratory. Seventy-five cryopreserved donor semen samples were evaluated. Samples were coded, then blindly evaluated for semen quality. Standard semen quality parameters, including concentration, motility parameters, World Health Organization criteria morphology, and strict criteria morphology. Significant differences were observed between donor semen banks for most semen quality parameters analyzed in intracervical insemination samples. In general, the greatest variability observed between banks was in percentage progressive sperm motility (range, 8.8 +/- 5.8 to 42.4 +/- 5.5) and normal sperm morphology (strict criteria; range, 10.1 +/- 3.3 to 26.6 +/- 4.7). Coefficients of variation within sperm banks were generally high. These data demonstrate the variability of donor semen quality provided by commercial sperm banks, both between banks and within a given bank. No relationship was observed between the size or type of sperm bank and the degree of variability. The data demonstrate the lack of uniformity in the criteria used to screen potential semen donors and emphasize the need for more stringent screening criteria and strict quality control in processing samples.

Development, optimization and validation of gas chromatographic fingerprinting of Brazilian commercial diesel fuel for quality control.

PubMed

dos Santos, Bruno César Diniz Brito; Flumignan, Danilo Luiz; de Oliveira, José Eduardo

2012-10-01

A three-step development, optimization and validation strategy is described for gas chromatography (GC) fingerprints of Brazilian commercial diesel fuel. A suitable GC-flame ionization detection (FID) system was selected to assay a complex matrix such as diesel. The next step was to improve acceptable chromatographic resolution with reduced analysis time, which is recommended for routine applications. Full three-level factorial designs were performed to improve flow rate, oven ramps, injection volume and split ratio in the GC system. Finally, several validation parameters were performed. The GC fingerprinting can be coupled with pattern recognition and multivariate regressions analyses to determine fuel quality and fuel physicochemical parameters. This strategy can also be applied to develop fingerprints for quality control of other fuel types.

Survey of quality indicators in commercial dehydrated fruits.

PubMed

Megías-Pérez, Roberto; Gamboa-Santos, Juliana; Soria, Ana Cristina; Villamiel, Mar; Montilla, Antonia

2014-05-01

Physical and chemical quality parameters (dry matter, aw, protein, carbohydrates, vitamin C, 2-furoylmethyl amino acids, rehydration ratio and leaching loss) have been determined in 30 commercial dehydrated fruits (strawberry, blueberry, raspberry, cranberry, cherry, apple, grapefruit, mango, kiwifruit, pineapple, melon, coconut, banana and papaya). For comparison purposes, strawberry samples processed in the laboratory by freeze-drying and by convective drying were used as control samples. Overall quality of dehydrated fruits seemed to be greatly dependent on processing conditions and, in a cluster analysis, samples which were presumably subjected to osmotic dehydration were separated from the rest of fruits. These samples presented the lowest concentration of vitamin C and the highest evolution of Maillard reaction, as evidenced by its high concentration of 2-furoylmethyl amino acids. This is the first study on the usefulness of this combination of chemical and physical indicators to assess the overall quality of commercial dehydrated fruits. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluation of commercial soybean cultivars for reaction to Phomopsis seed decay

USDA-ARS?s Scientific Manuscript database

Phomopsis seed decay (PSD), caused by Phomopsis longicolla (syn. Diaporthe longicolla), is an economically important soybean disease causing poor seed quality. Planting resistant cultivars is one of the most effective means to control PSD. In this study, 16 commercially available maturity groups IV ...

Carbon nuclear magnetic resonance spectroscopic fingerprinting of commercial gasoline: pattern-recognition analyses for screening quality control purposes.

PubMed

Flumignan, Danilo Luiz; Boralle, Nivaldo; Oliveira, José Eduardo de

2010-06-30

In this work, the combination of carbon nuclear magnetic resonance ((13)C NMR) fingerprinting with pattern-recognition analyses provides an original and alternative approach to screening commercial gasoline quality. Soft Independent Modelling of Class Analogy (SIMCA) was performed on spectroscopic fingerprints to classify representative commercial gasoline samples, which were selected by Hierarchical Cluster Analyses (HCA) over several months in retails services of gas stations, into previously quality-defined classes. Following optimized (13)C NMR-SIMCA algorithm, sensitivity values were obtained in the training set (99.0%), with leave-one-out cross-validation, and external prediction set (92.0%). Governmental laboratories could employ this method as a rapid screening analysis to discourage adulteration practices. Copyright 2010 Elsevier B.V. All rights reserved.

32 CFR 507.10 - Incorporation of designs or likenesses of approved designs in commercial articles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM... organizational insignia may be incorporated in articles manufactured for sale provided that permission has been... the coat of arms, crest, seal and organizational emblems. Such permission will be in writing...

Museums in the Commercial Marketplace: The Need for Licensing Agreements.

ERIC Educational Resources Information Center

Hodes, Scott; Gross, Karen

1978-01-01

Discussed are the major features of a Model Licensing Agreement to be used by museums in any commercial reproduction venture. They include rights and obligations of the respective parties, maintenance of quality control, payment of royalties, arbitration, and termination provisions. The Model Licensing Agreement is appended. (JMD)

Quality control tests of lab-reared Cydia pomonella and Cactoblastis cactorum field performance: Comparison of laboratory and field bioassays.

USDA-ARS?s Scientific Manuscript database

Research, operational, and commercial programs which rely on mass-reared insects of high quality and performance, need accurate methods for monitoring quality degradation during each step of production, handling and release. With continued interest in the use of the sterile insect technique (SIT) a...

Real Time Quality Control Methods for Cued EMI Data Collection

DTIC Science & Technology

2016-03-14

contents be construed as reflecting the official policy or position of the Department of Defense. Reference herein to any specific commercial product...This project evaluated the effectiveness of in-field quality control (QC) procedures during cued electromagnetic induction (EMI) data collection. The...electromagnetic induction ESTCP Environmental Security Technology Certification Program hr hour ISO Industry Standard Object IVS Instrument

Can the Roche hemolysis index be used for automated determination of cell-free hemoglobin? A comparison to photometric assays.

PubMed

Petrova, Darinka Todorova; Cocisiu, Gabriela Ariadna; Eberle, Christoph; Rhode, Karl-Heinz; Brandhorst, Gunnar; Walson, Philip D; Oellerich, Michael

2013-09-01

The aim of this study was to develop a novel method for automated quantification of cell-free hemoglobin (fHb) based on the HI (Roche Diagnostics). The novel fHb method based on the HI was correlated with fHb measured using the triple wavelength methods of both Harboe [fHb, g/L = (0.915 * HI + 2.634)/100] and Fairbanks et al. [fHb, g/L = (0.917 * HI + 2.131)/100]. fHb concentrations were estimated from the HI using the Roche Modular automated platform in self-made and commercially available quality controls, as well as samples from a proficiency testing scheme (INSTAND). The fHb using Roche automated HI results were then compared to results obtained using the traditional spectrophotometric assays for one hundred plasma samples with varying degrees of hemolysis, lipemia and/or bilirubinemia. The novel method using automated HI quantification on the Roche Modular clinical chemistry platform correlated well with results using the classical methods in the 100 patient samples (Harboe: r = 0.9284; Fairbanks et al.: r = 0.9689) and recovery was good for self-made controls. However, commercially available quality controls showed poor recovery due to an unidentified matrix problem. The novel method produced reliable determination of fHb in samples without interferences. However, poor recovery using commercially available fHb quality control samples currently greatly limits its usefulness. © 2013.

Gender disparities in the quality of cardiovascular disease care in private managed care plans.

PubMed

Chou, Ann F; Scholle, Sarah Hudson; Weisman, Carol S; Bierman, Arlene S; Correa-de-Araujo, Rosaly; Mosca, Lori

2007-01-01

Studies have shown that women with cardiovascular disease (CVD) are screened and treated less aggressively than men and are less likely to undergo cardiac procedures. Research in this area has primarily focused on the acute setting, and there are limited data on the ambulatory care setting, particularly among the commercially insured. To that end, the objective of this study is to determine if gender disparities in the quality of CVD care exist in commercial managed care populations. Using a national sample of commercial health plans, we analyzed member-level data for 7 CVD quality indicators from the Healthcare Effectiveness Data and Information Set (HEDIS) collected in 2005. We used hierarchical generalized linear models to estimate these HEDIS measures as a function of gender, controlling for race/ethnicity, socioeconomic status, age, and plans' clustering effects. Results showed that women were less likely than men to have low-density lipoprotein (LDL) cholesterol controlled at <100 mg/dL in those who have diabetes (odds ratio [OR], 0.81; 95% confidence interval [CI], 0.76-0.86) or a history of CVD (OR, 0.72; CI 95%, 0.64-0.82). The difference between men and women in meeting the LDL control measures was 5.74% among those with diabetes (44.3% vs. 38.5%) and 8.53% among those with a history of CVD (55.1% vs. 46.6%). However, women achieved higher performance than men in controlling blood pressure (OR, 1.12; 95% CI, 1.02-1.21), where the rate of women meeting this quality indicator exceeded that of men by 1.94% (70.8% for women vs. 68.9% for men). Gender disparities in the management and outcomes of CVD exist among patients in commercial managed care plans despite similar access to care. Poor performance in LDL control was seen in both men and women, with a lower rate of control in women suggesting the possibility of less intensive cholesterol treatment in women. The differences in patterns of care demonstrate the need for interventions tailored to address gender disparities.

[Quality of commercial inoculants for soybean crop in Argentina: concentration of viable rhizobia and presence of contaminants].

PubMed

Benintende, S

2010-01-01

In view of the inoculant production technology available, quality control is a necessary tool to improve soybean inoculants commercialized in Argentina. In 1988, the Facultad de Ciencias Agropecuarias de la Universidad Nacional de Entre Ríos (Argentina) created a quality control service for soybean crop inoculants to offer to farmers. The aim of this study was to evaluate the quality of soybean crop inoculants for seven cropping seasons and to contrast these results with those from previous investigations conducted in our country. This work was developed using 128 inoculant samples from 30 different trade names. The analyzed variables were: inoculant label information, number of viable rhizobia and presence of contaminants. Twenty per cent of the labels showed defects that did not comply with the Argentine legislation. The detected problems in inoculant labels were related to lot numbers or the expiry date, which lacked, was easy to remove or not visible. Eighty seven per cent of the analyzed inoculants were formulated in liquid carriers. Seventy six per cent of the samples had a number of rhizobia above 10(8) CFU/g or ml, the minimum quantity required by the legislation. Thirty per cent of the analyzed inoculants had contaminants and their presence was related to low rhizobia counts, as shown in a correspondence analysis. The relationship between liquid inoculants and the absence of contaminants was expressed. It can be concluded from the comparison of results found in this investigation with those in previous works published on Argentinean inoculants, that inoculant quality has been improved, although the situation is far from ideal. Adequate manufacturing and commercialization controls are necessary to ensure product quality.

Verification Testing of Air Pollution Control Technology Quality Management Plan Revision 2.3

EPA Pesticide Factsheets

The Air Pollution Control Technology Verification Center was established in 1995 as part of the EPA’s Environmental Technology Verification Program to accelerate the development and commercialization of improved environmental technologies’ performance.

[Multisite validation of CDT measurement by the %CDT TIA and the Tina Quant %CDT kits].

PubMed

Boehrer, J L; Cano, Y; Capolaghi, B; Desch, G; Dosbaa, I; Estepa, L; Hennache, B; Schellenberg, F

2007-01-01

The measurement of CDT (Carbohydrate Deficient Transferrin) is an essential biological tool in the diagnosis and follow-up of alcohol abuse. It is also employed as a marker of abstinence for the restitution of driving licences. However, the precision of measurement, and the between laboratory homogeneity of the results are still discussed. The ion exchange followed by immunodetermination of CDT is available in two products, the Tina Quant %CDT (Roche, Mannheim, Germany) and the %CDT TIA (Bio-Rad, Hercules, United States). This multicentre study was undertaken: 1) to evaluate the analytical characteristics of these kits and the homogeneity of the results from one laboratory to another, independently of the method used, 2) to validate the differences between the proposed normal values of both kits, 3) to study the possibility of using commercial control sera as external quality control. Four analytical systems were included in the study (Roche Modular/Hitachi 717, Beckman Coulter Immage and LX20, Dade Behring BNII). Determinations were carried out on pools of sera, commercial control sera, kit controls, and 30 serums of patients. These latter were also analyzed in capillary electrophoresis in order to establish correlations between the techniques. The calibrations were stable over one 2 weeks period. The repeatability of measurements spread out from 3,1% to 24,7%, for a mean value lower than 10%. The commercial control sera provided reliable results, with values adapted to a routine quality control use. The results of the Bio-Rad applications were lower by approximately 20% than those of the Roche application, which justifies the difference of the normal values (2,6% versus 3%), and an identical classification of the patients in at least 27 of the 30 samples. We conclude that the analytical quality of the compared techniques, even if it could be improved, is sufficient to guarantee a good reliability of the results. An external quality control could be proposed by using the control sera that we tested.

Integrated Neural Flight and Propulsion Control System

NASA Technical Reports Server (NTRS)

Kaneshige, John; Gundy-Burlet, Karen; Norvig, Peter (Technical Monitor)

2001-01-01

This paper describes an integrated neural flight and propulsion control system. which uses a neural network based approach for applying alternate sources of control power in the presence of damage or failures. Under normal operating conditions, the system utilizes conventional flight control surfaces. Neural networks are used to provide consistent handling qualities across flight conditions and for different aircraft configurations. Under damage or failure conditions, the system may utilize unconventional flight control surface allocations, along with integrated propulsion control, when additional control power is necessary for achieving desired flight control performance. In this case, neural networks are used to adapt to changes in aircraft dynamics and control allocation schemes. Of significant importance here is the fact that this system can operate without emergency or backup flight control mode operations. An additional advantage is that this system can utilize, but does not require, fault detection and isolation information or explicit parameter identification. Piloted simulation studies were performed on a commercial transport aircraft simulator. Subjects included both NASA test pilots and commercial airline crews. Results demonstrate the potential for improving handing qualities and significantly increasing survivability rates under various simulated failure conditions.

Evaluation of a commercially available organic acid product on body weight loss, carcass yield, and meat quality during preslaughter feed withdrawal in broiler chickens: a poultry welfare and economic perspective.

PubMed

Menconi, A; Kuttappan, V A; Hernandez-Velasco, X; Urbano, T; Matté, F; Layton, S; Kallapura, G; Latorre, J; Morales, B E; Prado, O; Vicente, J L; Barton, J; Andreatti Filho, R L; Lovato, M; Hargis, B M; Tellez, G

2014-02-01

The effect of a commercial organic acid (OA) product on BW loss (BWL) during feed withdrawal and transportation, carcass yield, and meat quality was evaluated in broiler chickens. Two experiments were conducted in Brazil. Commercial houses were paired as control groups receiving regular water and treated groups receiving OA in the water. Treated birds had a reduction in BWL of 37 g in experiment 1 and 32.2 g in experiment 2. In experiment 2, no differences were observed in carcass yield between groups. Estimation of the cost benefit suggested a 1:16 ratio by using the OA. In experiment 3, conducted in Mexico, significant differences on water consumption, BWL, and meat quality characteristics were observed in chickens that were treated with the OA (P < 0.05). These data suggest this OA product may improve animal welfare and economic concerns in the poultry industry by reducing BWL and improving meat quality attributes.

Commercial scale irradiation for insect disinfestation preserves peach quality

NASA Astrophysics Data System (ADS)

McDonald, Heather; McCulloch, Mary; Caporaso, Fred; Winborne, Ian; Oubichon, Michon; Rakovski, Cyril; Prakash, Anuradha

2012-06-01

Irradiation is approved as a generic quarantine treatment by the US Department of Agriculture, Animal and Plant Health Inspection Service. Due to the effectiveness of irradiation in controlling insects on commodities, there is a growing need to understand the effects of low dose irradiation on fruit quality. The goal of this study was to determine the sensitivity of peaches (Prunus persica) to irradiation, and secondly, to determine the effect of commercial scale treatment on shelf-life, overall quality and consumer liking. Six varieties of peaches were irradiated in small batches at 0.29, 0.49, 0.69 and 0.90 kGy to observe the sensitivity of peaches at different dose levels. Changes in quality were evaluated by 8 trained panelists using descriptive analysis. Sensory characteristics (color, smoothness, aroma, touch firmness, mouth firmness, graininess, overall flavor and off-flavor) were evaluated at 2-4 day intervals and untreated samples served as control. To simulate commercial treatment, peaches were irradiated in pallet quantities at a target dose level of 0.4 kGy. The average absorbed dose was 0.66 kGy with an average dose uniformity ratio of 1.57. Commercially treated peaches were evaluated by 40-80 untrained consumers for acceptability routinely throughout the shelf life. Titratable acidity, Brix, texture and weight loss were also monitored for both commercial and small scale irradiated peaches. There was no dose effect on TA, Brix and weight loss due to irradiation. Peaches irradiated at 0.69 and 0.90 kGy were darker in flesh color, more juicy and less firm as determined by the trained panel and analytical pressure tests. Commercial scale irradiation did not adversely affect shelf life but was seen to enhance ripening. This, however, was perceived as a positive change by consumers. Overall, consumers rated the acceptability of irradiated peaches higher than untreated peaches. Statistical analysis was performed using linear mixed models to find determinates of irradiation on peaches.

Comparative effects of gamma irradiation and phosphine fumigation on the quality of white ginseng

NASA Astrophysics Data System (ADS)

Kwon, J.-H. J.-H.; Byun, M.-W. M.-W.; Kim, K.-S. K.-S.; Kang, I.-J. I.-J.

2000-03-01

The hygienic, physicochemical, and organoleptic qualities of white ginseng were monitored during 6 months under accelerated conditions (40°C, 90% r.h.) by observing its microbial populations, disinfestation, and some quality attributes following either gamma irradiation at 2.5-10 kGy or commercial phosphine (PH 3) fumigation. In a comparative study, both treatments were found to be effective for disinfecting the stored samples. Phosphine showed no appreciable decontaminating effects on microorganisms contaminated including coliforms, while 5 kGy irradiation was sufficient to control all microorganisms related to the quality of the packed samples. Irradiation at 5 kGy caused negligible changes in physicochemical attributes of the samples, such as ginsenosides, amino acids, fatty acids, and organoleptic properties, whereas phosphine fumigation was found detrimental to sensory flavor ( P<0.01). Quality deterioration occurred in the commercially-packed samples was in the following order: the control, 10 kGy-, phosphine-, and 2.5-5 kGy-treated samples. Accordingly, irradiation at <5 kGy was found to be an effective alternative to phosphine fumigation for white ginseng.

[Basic principles, planning and implementation of non-commercial clinical trials].

PubMed

Finger, R P; Coch, C; Coenen, M; Mengel, M; Hartmann, G; Holz, F G

2011-01-01

The proof of a drug's efficacy in randomized controlled trials is fundamental to therapeutic concepts determined by evidence-based medicine. Clinical trials according to the German Medicinal Products Act are performed by the pharmaceutical industry as company-sponsored trials (CST) driven by commercial interests or by non-commercial facilities as investigator-initiated trials (IIT), typically implemented by University Hospitals. In areas with no commercial interest, IITs are the driving force that generate scientific progress leading to treatment optimization. Therefore, non-commercial or investigator-initiated clinical trials are indispensable for improving medical care. To ensure the safety of trial participants and the quality of the data obtained, clinical trials are controlled by many legal regulations and internationally accepted quality standards. Therefore implementation of a clinical trial requires profound knowledge, qualified personnel, appropriate infrastructure, and substantial financial resources. In IITs unlike CSTs this has to be accomplished by the University without the assistance of the pharmaceutical industry. Since teaching of skills needed to perform clinical trials is still largely neglected in medical school and during residency this review addresses the (in clinical trials) inexperienced physician and outlines the characterization of a clinical trial, the range and division of responsibilities and the performance of clinical trials according to the German Medicinal Products Act.

The commercial sector: marketing diet and fitness responsibly.

PubMed

Conley, R

1998-08-01

The commercial sector, through a range of products and services, is already heavily involved in the weight loss industry. Because of its capability to access millions of people, it has great potential for promoting public health through dietary and exercise practices. However, an absence of controls or advertising standards, safety and quality, currently threatens its credibility. This paper draws from my own experience developing a now well-established diet and fitness organisation. It makes the case that the best quality products and practice arise from close collaboration with scientific experts in the field. Effectiveness is increased through the distribution of sound educational messages, through an array of commercial options that include books, magazines, videos, television and diet and exercise clubs.

Resolving Identification Issues of Saraca asoca from Its Adulterant and Commercial Samples Using Phytochemical Markers

PubMed Central

Hegde, Satisha; Hegde, Harsha Vasudev; Jalalpure, Sunil Satyappa; Peram, Malleswara Rao; Pai, Sandeep Ramachandra; Roy, Subarna

2017-01-01

Saraca asoca (Roxb.) De Wilde (Ashoka) is a highly valued endangered medicinal tree species from Western Ghats of India. Besides treating cardiac and circulatory problems, S. asoca provides immense relief in gynecological disorders. Higher price and demand, in contrast to the smaller population size of the plant, have motivated adulteration with other plants such as Polyalthia longifolia (Sonnerat) Thwaites. The fundamental concerns in quality control of S. asoca arise due to its part of medicinal value (Bark) and the chemical composition. Phytochemical fingerprinting with proper selection of analytical markers is a promising method in addressing quality control issues. In the present study, high-performance liquid chromatography of phenolic compounds (gallic acid, catechin, and epicatechin) coupled to multivariate analysis was used. Five samples each of S. asoca, P. longifolia from two localities alongside five commercial market samples showed evidence of adulteration. Subsequently, multivariate hierarchical cluster analysis and principal component analysis was established to discriminate the adulterants of S. asoca. The proposed method ascertains identification of S. asoca from its putative adulterant P. longifolia and commercial market samples. The data generated may also serve as baseline data to form a quality standard for pharmacopoeias. SUMMARY Simultaneous quantification of gallic acid, catechin, epicatechin from Saraca asoca by high-performance liquid chromatographyDetection of S. asoca from adulterant and commercial samplesUse of analytical method along with a statistical tool for addressing quality issues. Abbreviations used: HPLC: High Performance Liquid Chromatography; RP-HPLC: Reverse Phase High Performance Liquid Chromatography; CAT: Catechin; EPI: Epicatechin; GA: Gallic acid; PCA: Principal Component Analysis. PMID:28808391

Quality Dashboards: Technical and Architectural Considerations of an Actionable Reporting Tool for Population Management

PubMed Central

Olsha-Yehiav, Maya; Einbinder, Jonathan S.; Jung, Eunice; Linder, Jeffrey A.; Greim, Julie; Li, Qi; Schnipper, Jeffrey L.; Middleton, Blackford

2006-01-01

Quality Dashboards (QD) is a condition-specific, actionable web-based application for quality reporting and population management that is integrated into the Electronic Health Record (EHR). Using server-based graphic web controls in a .Net environment to construct Quality Dashboards allows customization of the reporting tool without the need to rely on commercial business intelligence tool. Quality Dashboards will improve patient care and quality outcomes as clinicians utilize the reporting tool for population management. PMID:17238671

High-throughput assay for optimising microbial biological control agent production and delivery

USDA-ARS?s Scientific Manuscript database

Lack of technologies to produce and deliver effective biological control agents (BCAs) is a major barrier to their commercialization. A myriad of variables associated with BCA cultivation, formulation, drying, storage, and reconstitution processes complicates agent quality maximization. An efficie...

Measuring quality of adolescent preventive services of health plan enrollees and school-based health center users.

PubMed

Klein, Jonathan D; Handwerker, Lisa; Sesselberg, Tracy S; Sutter, Erika; Flanagan, Erinn; Gawronski, Beth

2007-08-01

To evaluate whether quality of care provided to adolescents enrolled in a community-based managed care plan was better for those who also received some care at school-based health centers (SBHCs). The Young Adult Health Care Survey (YAHCS) was administered to 374 adolescents (commercially insured, Medicaid-insured, and SBHC users) to assess risk behaviors, provision of preventive screening and counseling, and quality of care. SBHC users were most likely to report that their provider told them their discussions were confidential, and that they received screening/counseling on sexually transmitted diseases (STDs), HIV/AIDS, condom use, and birth control. Commercially insured adolescents were least likely to report discussion of sexual health issues. SBHC users had the highest mean YAHCS quality measure scores for screening/counseling on pregnancy/STDs, diet and exercise, and helpfulness of counseling provided; Medicaid-insured teens had the lowest scores on four of seven measures. Regression models controlled for demographics, use of screener, and site of care showed that use of a screener had a significant impact on six of seven quality measure models. Younger age predicted screening for risk behaviors; being female, African-American, and an SBHC user predicted screening on pregnancy/STDs. SBHCs may increase adolescents' access to confidential care, and SBHC providers may be more likely than those in other settings to screen and counsel patients about sexual health. Overall quality of preventive care reported by commercially insured adolescents may be better in some health content areas and worse in others compared with care reported by Medicaid-insured youth and SBHC users.

Optimizing anaerobic soil disinfestation for fresh market tomato production: Nematode and weed control, yield, and fruit quality

USDA-ARS?s Scientific Manuscript database

Anaerobic soil disinfestation (ASD) has potential as an alternative to chemical-fumigation for controlling soilborne pathogens and pests. Previously, control of nutsedge was sub-optimal and the quantity of inputs for commercial production was an impediment to adoption. Field studies were conducted i...

Reduced-cost Chlamydia trachomatis-specific multiplex real-time PCR diagnostic assay evaluated for ocular swabs and use by trachoma research programmes.

PubMed

Butcher, Robert; Houghton, Jo; Derrick, Tamsyn; Ramadhani, Athumani; Herrera, Beatriz; Last, Anna R; Massae, Patrick A; Burton, Matthew J; Holland, Martin J; Roberts, Chrissy H

2017-08-01

Trachoma, caused by the intracellular bacterium Chlamydia trachomatis (Ct), is the leading infectious cause of preventable blindness. Many commercial platforms are available that provide highly sensitive and specific detection of Ct DNA. However, the majority of these commercial platforms are inaccessible for population-level surveys in resource-limited settings typical to trachoma control programmes. We developed two low-cost quantitative PCR (qPCR) tests for Ct using readily available reagents on standard real-time thermocyclers. Each multiplex qPCR test targets one genomic and one plasmid Ct target in addition to an endogenous positive control for Homo sapiens DNA. The quantitative performance of the qPCR assays in clinical samples was determined by comparison to a previously evaluated droplet digital PCR (ddPCR) test. The diagnostic performance of the qPCR assays were evaluated against a commercial assay (artus C. trachomatis Plus RG PCR, Qiagen) using molecular diagnostics quality control standards and clinical samples. We examined the yield of Ct DNA prepared from five different DNA extraction kits and a cold chain-free dry-sample preservation method using swabs spiked with fixed concentrations of human and Ct DNA. The qPCR assay was highly reproducible (Ct plasmid and genomic targets mean total coefficients of variance 41.5% and 48.3%, respectively). The assay detected 8/8 core specimens upon testing of a quality control panel and performed well in comparison to commercially marketed comparator test (sensitivity and specificity>90%). Optimal extraction and sample preservation methods for research applications were identified. We describe a pipeline from collection to diagnosis providing the most efficient sample preservation and extraction with significant per test cost savings over a commercial qPCR diagnostic assay. The assay and its evaluation should allow control programs wishing to conduct independent research within the context of trachoma control, access to an affordable test with defined performance characteristics. Copyright © 2017. Published by Elsevier B.V.

Enhanced Quality Control in Pharmaceutical Applications by Combining Raman Spectroscopy and Machine Learning Techniques

NASA Astrophysics Data System (ADS)

Martinez, J. C.; Guzmán-Sepúlveda, J. R.; Bolañoz Evia, G. R.; Córdova, T.; Guzmán-Cabrera, R.

2018-06-01

In this work, we applied machine learning techniques to Raman spectra for the characterization and classification of manufactured pharmaceutical products. Our measurements were taken with commercial equipment, for accurate assessment of variations with respect to one calibrated control sample. Unlike the typical use of Raman spectroscopy in pharmaceutical applications, in our approach the principal components of the Raman spectrum are used concurrently as attributes in machine learning algorithms. This permits an efficient comparison and classification of the spectra measured from the samples under study. This also allows for accurate quality control as all relevant spectral components are considered simultaneously. We demonstrate our approach with respect to the specific case of acetaminophen, which is one of the most widely used analgesics in the market. In the experiments, commercial samples from thirteen different laboratories were analyzed and compared against a control sample. The raw data were analyzed based on an arithmetic difference between the nominal active substance and the measured values in each commercial sample. The principal component analysis was applied to the data for quantitative verification (i.e., without considering the actual concentration of the active substance) of the difference in the calibrated sample. Our results show that by following this approach adulterations in pharmaceutical compositions can be clearly identified and accurately quantified.

Interactions between 1-MCP and controlled atmosphere storage on quality and storage disorders of fruits and vegetable.

USDA-ARS?s Scientific Manuscript database

The use of 1-methycyclopropene (1-MCP) to maintain quality attributes of horticultural products has been investigated extensively. Commercial applications of 1-MCP (SmartFreshTM), are made to a range of horticultural crops, including avocados, bananas, melons, persimmons and tomatoes, but the major...

Interactions between 1-MCP and controlled atmospheres on quality and storage disorders of fruits and vegetable

USDA-ARS?s Scientific Manuscript database

The use of 1-methycyclopropene (1-MCP) to maintain quality attributes of horticultural products has been investigated extensively. Commercial applications of 1-MCP (SmartFreshTM), are made to a range of horticultural crops, including avocados, bananas, melons, persimmons and tomatoes, but the major...

Evaluation of a commercially available organic acid product on body weight loss, carcass yield, and meat quality during preslaughter feed withdrawal in broiler chickens: A poultry welfare and economic perspective1

PubMed Central

Menconi, A.; Kuttappan, V. A.; Hernandez-Velasco, X.; Urbano, T.; Matté, F.; Layton, S.; Kallapura, G.; Latorre, J.; Morales, B. E.; Prado, O.; Vicente, J. L.; Barton, J.; Filho, R. L. Andreatti; Lovato, M.; Hargis, B. M.; Tellez, G.

2014-01-01

The effect of a commercial organic acid (OA) product on BW loss (BWL) during feed withdrawal and transportation, carcass yield, and meat quality was evaluated in broiler chickens. Two experiments were conducted in Brazil. Commercial houses were paired as control groups receiving regular water and treated groups receiving OA in the water. Treated birds had a reduction in BWL of 37 g in experiment 1 and 32.2 g in experiment 2. In experiment 2, no differences were observed in carcass yield between groups. Estimation of the cost benefit suggested a 1:16 ratio by using the OA. In experiment 3, conducted in Mexico, significant differences on water consumption, BWL, and meat quality characteristics were observed in chickens that were treated with the OA (P < 0.05). These data suggest this OA product may improve animal welfare and economic concerns in the poultry industry by reducing BWL and improving meat quality attributes. PMID:24570468

Exchanging a few commercial, regularly consumed food items with improved fat quality reduces total cholesterol and LDL-cholesterol: a double-blind, randomised controlled trial.

PubMed

Ulven, Stine M; Leder, Lena; Elind, Elisabeth; Ottestad, Inger; Christensen, Jacob J; Telle-Hansen, Vibeke H; Skjetne, Anne J; Raael, Ellen; Sheikh, Navida A; Holck, Marianne; Torvik, Kristin; Lamglait, Amandine; Thyholt, Kari; Byfuglien, Marte G; Granlund, Linda; Andersen, Lene F; Holven, Kirsten B

2016-10-01

The healthy Nordic diet has been previously shown to have health beneficial effects among subjects at risk of CVD. However, the extent of food changes needed to achieve these effects is less explored. The aim of the present study was to investigate the effects of exchanging a few commercially available, regularly consumed key food items (e.g. spread on bread, fat for cooking, cheese, bread and cereals) with improved fat quality on total cholesterol, LDL-cholesterol and inflammatory markers in a double-blind randomised, controlled trial. In total, 115 moderately hypercholesterolaemic, non-statin-treated adults (25-70 years) were randomly assigned to an experimental diet group (Ex-diet group) or control diet group (C-diet group) for 8 weeks with commercially available food items with different fatty acid composition (replacing SFA with mostly n-6 PUFA). In the Ex-diet group, serum total cholesterol (P<0·001) and LDL-cholesterol (P<0·001) were reduced after 8 weeks, compared with the C-diet group. The difference in change between the two groups at the end of the study was -9 and -11 % in total cholesterol and LDL-cholesterol, respectively. No difference in change in plasma levels of inflammatory markers (high-sensitive C-reactive protein, IL-6, soluble TNF receptor 1 and interferon-γ) was observed between the groups. In conclusion, exchanging a few regularly consumed food items with improved fat quality reduces total cholesterol, with no negative effect on levels of inflammatory markers. This shows that an exchange of a few commercially available food items was easy and manageable and led to clinically relevant cholesterol reduction, potentially affecting future CVD risk.

Internal quality assurance in a clinical virology laboratory. II. Internal quality control.

PubMed Central

Gray, J J; Wreghitt, T G; McKee, T A; McIntyre, P; Roth, C E; Smith, D J; Sutehall, G; Higgins, G; Geraghty, R; Whetstone, R

1995-01-01

AIMS--In April 1991 additional quality control procedures were introduced into the virology section of the Clinical Microbiology and Public Health Laboratory, Cambridge. Internal quality control (IQC) samples were gradually included in the serological assays performed in the laboratory and supplemented kit controls and standard sera. METHODS--From April 1991 to December 1993, 2421 IQC procedures were carried out with reference sera. RESULTS--The IQC samples were evaluated according to the Westgard rules. Violations were recorded in 60 of 1808 (3.3%) controls and were highest in the IQC samples of complement fixation tests (25/312 (8%) of controls submitted for complement fixation tests). CONCLUSIONS--The inclusion of IQC samples in the serological assays performed in the laboratory has highlighted batch to batch variation in commercial assays. The setting of acceptable limits for the IQC samples has increased confidence in the validity of assay results. PMID:7730475

Results of the Medicare Health Support disease-management pilot program.

PubMed

McCall, Nancy; Cromwell, Jerry

2011-11-03

In the Medicare Modernization Act of 2003, Congress required the Centers for Medicare and Medicaid Services to test the commercial disease-management model in the Medicare fee-for-service program. The Medicare Health Support Pilot Program was a large, randomized study of eight commercial programs for disease management that used nurse-based call centers. We randomly assigned patients with heart failure, diabetes, or both to the intervention or to usual care (control) and compared them with the use of a difference-in-differences method to evaluate the effects of the commercial programs on the quality of clinical care, acute care utilization, and Medicare expenditures for Medicare fee-for-service beneficiaries. The study included 242,417 patients (163,107 in the intervention group and 79,310 in the control group). The eight commercial disease-management programs did not reduce hospital admissions or emergency room visits, as compared with usual care. We observed only 14 significant improvements in process-of-care measures out of 40 comparisons. These modest improvements came at substantial cost to the Medicare program in fees paid to the disease-management companies ($400 million), with no demonstrable savings in Medicare expenditures. In this large study, commercial disease-management programs using nurse-based call centers achieved only modest improvements in quality-of-care measures, with no demonstrable reduction in the utilization of acute care or the costs of care.

Healthy Building Design for the Commercial, Industrial, and Institutional Marketplace.

ERIC Educational Resources Information Center

Turner, William A.

Building design and construction that helps deliver both superior air quality and occupant thermal comfort, while minimizing energy consumption, are examined. The paper explores an integrated building systems approach that combines the principles of "directed air flow control" and "demand controlled ventilation" where ventilation is effectively…

Biological control of aflatoxin is effective and economical in Mississippi field trials

USDA-ARS?s Scientific Manuscript database

Aflatoxin contamination of corn is a major grain quality issue and can be a major economic limiting factor to Mississippi corn farmers. Biological control products based on aflatoxin non-producing strains of Aspergillus flavus are commercially available to prevent the contamination of corn with afl...

32 CFR 507.12 - Possession and wearing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.12..., society, or other group of persons without prior approval in writing by the Secretary of the Army or the...

32 CFR 507.12 - Possession and wearing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.12..., society, or other group of persons without prior approval in writing by the Secretary of the Army or the...

32 CFR 507.12 - Possession and wearing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.12..., society, or other group of persons without prior approval in writing by the Secretary of the Army or the...

32 CFR 507.12 - Possession and wearing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.12..., society, or other group of persons without prior approval in writing by the Secretary of the Army or the...

32 CFR 507.12 - Possession and wearing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.12..., society, or other group of persons without prior approval in writing by the Secretary of the Army or the...

Implementing self sustained quality control procedures in a clinical laboratory.

PubMed

Khatri, Roshan; K C, Sanjay; Shrestha, Prabodh; Sinha, J N

2013-01-01

Quality control is an essential component in every clinical laboratory which maintains the excellence of laboratory standards, supplementing to proper disease diagnosis, patient care and resulting in overall strengthening of health care system. Numerous quality control schemes are available, with combinations of procedures, most of which are tedious, time consuming and can be "too technical" whereas commercially available quality control materials can be expensive especially for laboratories in developing nations like Nepal. Here, we present a procedure performed at our centre with self prepared control serum and use of simple statistical tools for quality assurance. The pooled serum was prepared as per guidelines for preparation of stabilized liquid quality control serum from human sera. Internal Quality Assessment was performed on this sample, on a daily basis which included measurement of 12 routine biochemical parameters. The results were plotted on Levey-Jennings charts and analysed with quality control rules, for a period of one month. The mean levels of biochemical analytes in self prepared control serum were within normal physiological range. This serum was evaluated every day along with patients' samples. The results obtained were plotted on control charts and analysed using common quality control rules to identify possible systematic and random errors. Immediate mitigation measures were taken and the dispatch of erroneous reports was avoided. In this study we try to highlight on a simple internal quality control procedure which can be performed by laboratories, with minimum technology, expenditure, and expertise and improve reliability and validity of the test reports.

A novel approach to rapidly explore analytical markers for quality control of Radix Salviae Miltiorrhizae extract granules by robust principal component analysis with ultra-high performance liquid chromatography-ultraviolet-quadrupole time-of-flight mass spectrometry.

PubMed

Song, Jing-Zheng; Li, Song-Lin; Zhou, Yan; Qiao, Chun-Feng; Chen, Shi-Lin; Xu, Hong-Xi

2010-11-02

In a well-controlled experiment, outliers discriminated by robust principal component analysis (RPCA) represent contents in samples which are of particular quality distinguishable from the rest of the others, therefore chemical constituents in a natural product causing discrimination between outliers and the majority of samples could be considered as analytical markers for quality control. Based on this strategy, a novel approach for rapidly exploring characteristic analytical markers was proposed for the quality control of extract granules of Radix Salviae Miltiorrhizae (EGRSM). In this study, large sizes of samples were analyzed via high-throughput ultra-high performance liquid chromatography-ultraviolet-quadrupole time-of-flight mass spectrometry (UHPLC-UV-Q-Tof MS). RPCA was first performed on the three groups of samples: RSM (the raw material), the in-house prepared aqueous extract of Radix Salviae Miltiorrhizae (AERSM) and commercial product of EGRSM, to determine the variation of specific constituents between raw material and the final products as well as the effect of manufacturing process on the overall quality. Then RPCA was performed on the commercial products of EGRSM to explore the applicability of identified characteristic markers for the quality control of EGRSM. Candidate markers were extracted by RPCA, and their molecular formulae were determined by high resolution electrospray ionization-mass spectrometric (ESI-MS) analysis. The suitability of identified markers was then evaluated by determining the relationship between quantities of the identified markers with their antioxidant activities biologically, and further confirmed in a variety of samples. In conclusion, the combination of RPCA with UHPLC-UV-Q-Tof MS is a reliable means to identify chemical markers for evaluating quality of herbal medicines. Copyright (c) 2010 Elsevier B.V. All rights reserved.

[Role of medium-sized independent laboratories in control of healthcare-associated infection].

PubMed

Anzai, Eiko; Fukui, Toru

2009-05-01

In 2006, the Ministry of Health and Welfare revised the regulations regarding the Medical Service Law. The amendments stipulate that all healthcare institutions are required to implement infection control programs. However, small hospitals and clinics have no clinical microbiology laboratories, whereas medium-sized hospitals have few medical technologists and the outsourcing of microbiology tests to independent laboratories is common. The decreasing number of laboratories and recent outsourcing tendency reflect the increasing commercialization, and, with it, the escalating number of commercially operating chains. Each independent laboratory is responsible for supporting activities related to the surveillance, control, and prevention of healthcare-associated infections in the associated small and medium-sized hospitals. The people responsible for infection control in these hospitals usually do not have a background in microbiology. The evaluation of communication between independent laboratory staff and hospital personnel, and rapid turnaround time of microbiology laboratory test reports are important elements ensuring the quality of independent laboratory work. With the pressures of financial constraints in the Japanese medical insurance system, the development of a cost-effective and practical protocol for quality assurance is a real dilemma.

Industry's View on Using Quality Control, Biorelevant, and Clinically Relevant Dissolution Tests for Pharmaceutical Development, Registration, and Commercialization.

PubMed

Grady, Haiyan; Elder, David; Webster, Gregory K; Mao, Yun; Lin, Yiqing; Flanagan, Talia; Mann, James; Blanchard, Andy; Cohen, Michael J; Lin, Judy; Kesisoglou, Filippos; Hermans, Andre; Abend, Andreas; Zhang, Limin; Curran, David

2018-01-01

This article intends to summarize the current views of the IQ Consortium Dissolution Working Group, which comprises various industry companies, on the roles of dissolution testing throughout pharmaceutical product development, registration, commercialization, and beyond. Over the past 3 decades, dissolution testing has evolved from a routine and straightforward test as a component of end-product release into a comprehensive set of tools that the developer can deploy at various stages of the product life cycle. The definitions of commonly used dissolution approaches, how they relate to one another and how they may be applied in modern drug development, and life cycle management is described in this article. Specifically, this article discusses the purpose, advantages, and limitations of quality control, biorelevant, and clinically relevant dissolution methods. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Commercially available molecular tests for human papillomaviruses (HPV): 2015 update.

PubMed

Poljak, Mario; Kocjan, Boštjan J; Oštrbenk, Anja; Seme, Katja

2016-03-01

Commercial molecular tests for human papillomaviruses (HPV) are invaluable diagnostic tools in cervical carcinoma screening and management of women with cervical precancerous lesions as well as important research tools for epidemiological studies, vaccine development, and implementation and monitoring of vaccination programs. In this third inventory of commercial HPV tests, we identified 193 distinct commercial HPV tests and at least 127 test variants available on the market in 2015, which represents a 54% and 79% increase in the number of distinct HPV tests and variants, respectively, in comparison to our last inventory performed in 2012. Identified HPV tests were provisionally divided into eight main groups and several subgroups. Among the 193 commercial HPV tests, all but two target alpha-HPV types only. Although the number of commercial HPV tests with at least one published study in peer-reviewed literature has increased significantly in the last three years, several published performance evaluations are still not in line with agreed-upon standards in the HPV community. Manufacturers should invest greater effort into evaluating their products and publishing validation/evaluation results in peer-reviewed journals. To achieve this, more clinically oriented external quality-control panels and initiatives are required. For evaluating the analytical performance of the entire range of HPV tests currently on the market, more diverse and reliable external quality-control programs based on international standards for all important HPV types are indispensable. The performance of a wider range of HPV tests must be promptly evaluated on a variety of alternative clinical specimens. In addition, more complete HPV assays containing validated sample-extraction protocols and appropriate internal controls are urgently needed. Provision of a broader range of automated systems allowing large-scale HPV testing as well as the development of reliable, rapid, and affordable molecular point-of-care tests are priorities for the further improvement of HPV tests. Copyright © 2015 Elsevier B.V. All rights reserved.

Stability assessment of QKD procedures in commercial quantum cryptography systems versus quality of dark channel

NASA Astrophysics Data System (ADS)

Jacak, Monika; Melniczuk, Damian; Jacak, Janusz; Jóźwiak, Ireneusz; Gruber, Jacek; Jóźwiak, Piotr

2015-02-01

In order to assess the susceptibility of the quantum key distribution (QKD) systems to the hacking attack including simultaneous and frequent system self-decalibrations, we analyze the stability of the QKD transmission organized in two commercially available systems. The first one employs non-entangled photons as flying qubits in the dark quantum channel for communication whereas the second one utilizes the entangled photon pairs to secretly share the cryptographic key. Applying standard methods of the statistical data analysis to the characteristic indicators of the quality of the QKD communication (the raw key exchange rate [RKER] and the quantum bit error rate [QBER]), we have estimated the pace of the self-decalibration of both systems and the repeatability rate in the case of controlled worsening of the dark channel quality.

Drinking Water Quality in Hospitals and Other Buildings ...

EPA Pesticide Factsheets

Drinking water quality entering large buildings is generally adequately controlled by the water utility, but localized problems may occur within building or “premise” plumbing. Particular concerns are loss of disinfectant residual and temperature variability, which may enhance pathogen activity and metallic corrosion. Disinfection systems are available to building managers and are being installed in a variety of commercial buildings (hospitals, hotels, office buildings.) Yet our understanding of such additional treatment and of how to monitor end water quality at these buildings is limited. This class lecture will discuss challenges in maintaining acceptable water quality in hospitals, schools and other buildings. To give a lecture to a class of graduate students (ENVE 6054: Physical/Chemical Processes for Water Quality Control) at the University of Cincinnati, by presenting past research projects.

Impact of supplementing diets with propolis on productive performance, egg quality traits and some haematological variables of laying hens.

PubMed

Abdel-Kareem, A A A; El-Sheikh, T M

2017-06-01

One hundred and twenty eight, 28-weeks-old Lohmann LSL hybrid layers were used in this experiment, which lasted 12 weeks to investigate the effect of propolis supplementation on the productive performance, egg quality traits and haematological variables of laying hens. All hens were randomly classified into four equal experimental groups, eight replicates (4 birds/each). Hens in group 1 were fed on a commercial diet and considered as control group, while those in groups 2, 3 and 4 were fed on the same commercial diet and supplemented with 250, 500 and 1000 mg propolis/kg diet. The obtained results revealed that daily feed consumption/hen increased insignificantly with increasing propolis level than that of the control group. Regarding the means of egg mass and egg production rate, it was observed that the laying hens fed diets containing 250 and 1000 mg propolis/kg significantly (p < 0.05) produced more and heaver egg in comparison with control group. External egg quality traits have not affected with increasing the level of propolis, while eggshell weight was significantly (p < 0.05) increased. The internal egg quality traits except albumen and yolk percentages increased significantly (p < 0.05) with increasing propolis level for treated hens as compared to those in the control. Concerning the haematological parameters, the results showed that the levels of total protein and globulin increased significantly with increasing propolis level, while cholesterol and liver enzymes were significantly decreased (p < 0.05). Heterophils count of hens in the treated groups significantly decreased, whereas the lymphocyte count significantly increased, resulting in a decreased H/L ratio than that of the control group. Thus, it could be concluded that the supplementation of 250 mg propolis/kg diet is highly recommended to improving egg production, blood constituent and haematological parameters of the commercial laying hens. Journal of Animal Physiology and Animal Nutrition © 2015 Blackwell Verlag GmbH.

Control Strategies for Drug Product Continuous Direct Compression-State of Control, Product Collection Strategies, and Startup/Shutdown Operations for the Production of Clinical Trial Materials and Commercial Products.

PubMed

Almaya, Ahmad; De Belder, Lawrence; Meyer, Robert; Nagapudi, Karthik; Lin, Hung-Ren Homer; Leavesley, Ian; Jayanth, Jayanthy; Bajwa, Gurjit; DiNunzio, James; Tantuccio, Anthony; Blackwood, Dan; Abebe, Admassu

2017-04-01

Continuous manufacturing (CM) has emerged in the pharmaceutical industry as a paradigm shift with significant advantages related to cost, efficiency, flexibility, and higher assurance of quality. The inherent differences from batch processes justify examining the CM control strategy more holistically. This article describes the current thinking for the control and implementation of CM, using the example of a direct compression process and taking into consideration the ICH Q10 definition of "state of control" and process validation requirements. Statistical process control using control charts, sources of variation, process capability, and process performance is explained as a useful concept that can help assess the impact of variation within a batch and indicates if a process is in state of control. The potential for time-variant nature of startup and shutdown with CM is discussed to assure product quality while minimizing waste as well as different options for detection and isolation of non-conforming materials due to process upsets. While different levels of control are possible with CM, an appropriate balance between process control and end product testing is needed depending on the level of process understanding at the different stages of development from the production of clinical supplies through commercialization. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

A method for identifying boundary interference in PADV data

USDA-ARS?s Scientific Manuscript database

Recent commercialization of profiling acoustic Doppler velocimeters (PADVs) has enabled researchers to measure velocities at high frequencies simultaneously at specified increments over the instrument measurement range. The quantity of data output by PADVs can be large, hence robust quality control...

Assessment of the quality of harms reporting in non-randomised studies and randomised controlled studies of topiramate for the treatment of epilepsy using CONSORT criteria.

PubMed

Carmichael, Katie; Nolan, Sarah J; Weston, Jennifer; Tudur Smith, Catrin; Marson, Anthony G

2015-08-01

Treatment decisions should be informed by high quality evidence of both the potential benefit and harms of treatment alternatives. Randomised controlled trials (RCTs) provide the best evidence regarding benefits; however information relating to serious, rare and long-term harms is usually available only from non-randomised studies (NRSs). The aim of this study was to use a checklist based on the CONSORT (Consolidating Standards for Reporting Trials) extension for harms recommendations to assess the quality of reporting of harms data in both NRSs and RCTs of antiepileptic drugs, using studies of topiramate as an example. Seventy-eight studies were included from an online search of seven databases. Harms data was extracted from each study using a 25-point checklist. The mean number of items met was 11.5 (SD 2.96) per study. Commercially funded studies met on average 12.7 items and non-commercially funded studies met 10.08 (p value < 0.001). RCTs met on average 13.0 items and NRSs met 10.8 (p = 0.001). Multi-centre studies and commercially funded studies met significantly more items than single centre and non-commercially funded studies respectively. There was no significant difference in the mean number of items met by studies that had included adult vs. child participants, or studies published pre- vs. post-CONSORT extension for harms in 2004. Reporting of harms is significantly better in RCTs than in NRSs of TPM, but is suboptimal overall and has not improved since the publication of CONSORT extension for harms in 2004. There is a need to improve the reporting of harms in order to better inform treatment decisions. Copyright © 2015 Elsevier B.V. All rights reserved.

Smell of Stress: Identification of Induced Biochemical Pathways Affecting the Volatile Composition and Flavor Quality of Crops.

PubMed

Wüst, Matthias

2018-04-11

Recent research has shown that the biosynthesis of several key odorants is controlled by genes whose expression is altered or even induced by biotic or abiotic stress. These new findings provide a roadmap for improvement of flavor quality by the application of moderate, well-controlled stress. This strategy aims at reducing the flavor deficiencies in modern commercial varieties as a "green" alternative to genetic engineering. The workflow for a successful implementation of this approach, from the identification of key odorants by molecular science techniques to the investigation of mechanisms controlling their biosynthesis, is complex and calls for interdisciplinary research.

Stepwise heating in Stille polycondensation toward no batch-to-batch variations in polymer solar cell performance.

PubMed

Lee, Sang Myeon; Park, Kwang Hyun; Jung, Seungon; Park, Hyesung; Yang, Changduk

2018-05-14

For a given π-conjugated polymer, the batch-to-batch variations in molecular weight (M w ) and polydispersity index (Ð) can lead to inconsistent process-dependent material properties and consequent performance variations in the device application. Using a stepwise-heating protocol in the Stille polycondensation in conjunction with optimized processing, we obtained an ultrahigh-quality PTB7 polymer having high M w and very narrow Ð. The resulting ultrahigh-quality polymer-based solar cells demonstrate up to 9.97% power conversion efficiencies (PCEs), which is over 24% enhancement from the control devices fabricated with commercially available PTB7. Moreover, we observe almost negligible batch-to-batch variations in the overall PCE values from ultrahigh-quality polymer-based devices. The proposed stepwise polymerization demonstrates a facile and effective strategy for synthesizing high-quality semiconducting polymers that can significantly improve device yield in polymer-based solar cells, an important factor for the commercialization of organic solar cells, by mitigating device-to-device variations.

Lead/acid batteries in systems to improve power quality

NASA Astrophysics Data System (ADS)

Taylor, P.; Butler, P.; Nerbun, W.

Increasing dependence on computer technology is driving needs for extremely high-quality power to prevent loss of information, material, and workers' time that represent billions of dollars annually. This cost has motivated commercial and Federal research and development of energy storage systems that detect and respond to power-quality failures in milliseconds. Electrochemical batteries are among the storage media under investigation for these systems. Battery energy storage systems that employ either flooded lead/acid or valve-regulated lead/acid battery technologies are becoming commercially available to capture a share of this emerging market. Cooperative research and development between the US Department of Energy and private industry have led to installations of lead/acid-based battery energy storage systems to improve power quality at utility and industrial sites and commercial development of fully integrated, modular battery energy storage system products for power quality. One such system by AC Battery Corporation, called the PQ2000, is installed at a test site at Pacific Gas and Electric Company (San Ramon, CA, USA) and at a customer site at Oglethorpe Power Corporation (Tucker, GA, USA). The PQ2000 employs off-the-shelf power electronics in an integrated methodology to control the factors that affect the performance and service life of production-model, low-maintenance, flooded lead/acid batteries. This system, and other members of this first generation of lead/acid-based energy storage systems, will need to compete vigorously for a share of an expanding, yet very aggressive, power quality market.

Low cost solar array project. Experimental process system development unit for producing semiconductor-grade silicon using the silane-to-silicon process

NASA Technical Reports Server (NTRS)

1980-01-01

Technical activities are reported in the design of process, facilities, and equipment for producing silicon at a rate and price comensurate with production goals for low cost solar cell modules. The silane-silicone process has potential for providing high purity poly-silicon on a commercial scale at a price of fourteen dollars per kilogram by 1986, (1980 dollars). Commercial process, economic analysis, process support research and development, and quality control are discussed.

Conceptual design study of a V/STOL lift fan commercial short haul transport

NASA Technical Reports Server (NTRS)

Knight, R. G.; Powell, W. V., Jr.; Prizlow, J. A.

1973-01-01

Conceptual designs of V/STOL lift fan commercial short haul transport aircraft for the 1980-85 time period were studied to determine their technical and economic feasibility. The engine concepts included both integral and remote fans. The scope of the study included definition of the hover control concept for each propulsion system, aircraft design, mass properties, cruise performance, noise and ride qualities evaluation. Economic evaluation was also studied on the basis of direct-operating costs and route structure.

Conceptual design of a V/STOL lift fan commercial short haul transport

NASA Technical Reports Server (NTRS)

1973-01-01

Conceptual designs of V/STOL lift-fan commercial short-haul transport aircraft for the 1980-85 time period were studied to determine their technical and economic feasibility. Engine concepts studied included both integral remote fans. The scope of the study included definition of the hover control concept for each propulsion system, aircraft design, aircraft mass properties, cruise performance noise, and ride qualities evaluation. Economic evaluation was also studied on a basis of direct operating cost and route structure.

Food Fortification Stability Study

NASA Technical Reports Server (NTRS)

Sirmons, T. A.; Cooper, M. R.; Douglas, G. L.

2016-01-01

This study aims to assess the stability of vitamin content, sensory acceptability and color variation in fortified spaceflight foods over a period of 2 years. Findings will identify optimal formulation, processing, and storage conditions to maintain stability and acceptability of commercially available fortification nutrients. Changes in food quality are being monitored to indicate whether fortification affects quality over time (compared to the unfortified control), thus indicating their potential for use on long-duration missions.

Food Fortification Stability Study

NASA Technical Reports Server (NTRS)

Sirmons, T. A.; Cooper, M. R.; Douglas, G. L.

2017-01-01

This study aimed to assess the stability of vitamin content, sensory acceptability and color variation in fortified spaceflight foods over a period of two years. Findings will help to identify optimal formulation, processing, and storage conditions to maintain stability and acceptability of commercially available fortification nutrients. Changes in food quality were monitored to indicate whether fortification affects quality over time (compared to the unfortified control), thus indicating their potential for use on long-duration missions.

Low-Cost Quality Control and Nondestructive Evaluation Technologies for General Aviation Structures

NASA Technical Reports Server (NTRS)

Cramer, K. Elliott; Gavinsky, Bob; Semanskee, Grant

1998-01-01

NASA's Advanced General Aviation Transport Experiments (AGATE) Program has as a goal to reduce the overall cost of producing private aviation aircraft while maintaining the safety of these aircraft. In order to successfully meet this goal, it is necessary to develop nondestructive inspection techniques which will facilitate the production of the materials used in these aircraft and assure the quality necessary to maintain airworthiness. This paper will discuss a particular class of general aviation materials and several nondestructive inspection techniques that have proven effective for making these inspections. Additionally, this paper will discuss the investigation and application of other commercially available quality control techniques applicable to these structures.

Issues in Commercial Document Delivery.

ERIC Educational Resources Information Center

Marcinko, Randall Wayne

1997-01-01

Discusses (1) the history of document delivery; (2) the delivery process--end-user request, intermediary request, vendor reference, citation verification, obtaining document and source relations, quality control, transferring document to client, customer service and status, invoicing and billing, research and development, and copyright; and (3)…

Carboxyhaemoglobin: a possible reference material for haemoglobin assay.

PubMed Central

Rideout, J M; Louderback, A

1982-01-01

The inter- and intralaboratory quality control of haemoglobin estimation in remote laboratories requires a more rugged control haemolysate than is commercially available. The stabilities of oxyhaemoglobin and carboxyhaemoglobin forms of an ethanediol-containing haemolysate were studied over a three-year period. From the results obtained, carboxyhaemoglobin under nitrogen is proposed as a possible candidate reference material for haemoglobin assay. PMID:7068921

Short communication: Microbial quality of raw milk following commercial long-distance hauling.

PubMed

Darchuk, Emily M; Meunier-Goddik, Lisbeth; Waite-Cusic, Joy

2015-12-01

Hauling is a critical part of the commercial milk supply chain, yet very few studies have aimed to understand its effect on raw milk quality. This study focused on the effect of extended-duration tanker use during hauling on raw milk quality at a commercial facility. Standard tanker use [cleaned-in-place (CIP) once per 24h] served as a control and an incremental between-load water rinse with sanitizer treatment (RS) was evaluated to mitigate any effect from extended duration hauling. During this study, 1 commercial truck with 2 trailers was monitored for 10d. The truck collected milk at a large dairy farm, transported the milk to a manufacturing facility, and then returned to the same farm for a second load. Each round-trip journey took between 10 and 12h, allowing for 2 loads per 24-h use period. Following the second delivery, the truck was cleaned by CIP treatment starting a new treatment day. Producer samples were collected from the raw milk bulk tank on the farm before loading milk into the tanker. The same milk was sampled directly out of the tanker truck before unloading at the manufacturer. Effect on individual bacteria count, thermophilic spore count, and preliminary incubation count was quantified through common industry tests. Surface sponge swabs were also used to monitor tanker sanitation and the efficacy of cleaning treatments. Results did not identify a negative effect on raw milk quality due to extended duration hauling. Whereas the addition of RS did not provide any measurable quality benefits for the microbial milk quality, swab results demonstrated that the RS treatment was able to reduce surface bacteria in the tanker, although not to the same level as the full CIP treatment. Based on this study, current CIP practices for long distance milk hauling appear to be effective in mitigating any measurable effect on raw milk quality. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

32 CFR 507.6 - Authority to manufacture.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 3 2010-07-01 2010-07-01 true Authority to manufacture. 507.6 Section 507.6... PUBLIC RELATIONS MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Manufacture and Sale of Decorations, Medals, Badges...

76 FR 69214 - Approval and Promulgation of Air Quality Implementation Plans; Virginia; Consumer and Commercial...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-08

... portable fuel containers, consumer products, architectural and industrial (AIM) coatings, adhesives and... the control technology, testing, monitoring, administrative, recordkeeping, and reporting requirements... and products subject to the standards subject to the provisions of Chapter 45, specify monitoring...

An evaluation system for characterization of polysaccharides from the fruiting body of Hericium erinaceus and identification of its commercial product.

PubMed

Wu, Ding-Tao; Li, Wen-Zhi; Chen, Jun; Zhong, Qian-Xia; Ju, Yao-Jun; Zhao, Jing; Bzhelyansky, Anton; Li, Shao-Ping

2015-06-25

An evaluation system including colorimetric assay with iodine and potassium iodide, HPSEC-MALLS-RID analysis, GC-MS analysis, and saccharide mapping based on PACE analysis was proposed for the identification and discrimination of commercial product of Hericium erinaceus based on the chemical characters of polysaccharides in H. erinaceus fruiting body collected from different regions of China. The results showed that the molecular weights, the compositional monosaccharides and the glycosidic linkages of polysaccharides in H. erinaceus collected from different regions of China were similar, respectively. However, polysaccharides in the widely consumed product of H. erinaceus in China were significantly different from those of H. erinaceus fruiting body. The implications from these results were found to be beneficial to improve the quality control of polysaccharides from the H. erinaceus fruiting body, and suggest that the proposed evaluation system could be used as a routine approach for the quality control of polysaccharides in other edible and medicinal mushrooms. Copyright © 2015 Elsevier Ltd. All rights reserved.

A 3D-printed device for polymer nanoimprint lithography

NASA Astrophysics Data System (ADS)

Caño-García, Manuel; Geday, Morten A.; Gil-Valverde, Manuel; Megías Zarco, Antonio; Otón, José M.; Quintana, Xabier

2018-02-01

Nanoimprint lithography (NIL) is an imprinting technique which has experienced an increasing popularity due to its versatility in fabrication processes. Commercial NIL machines are readily available achieving high quality results; however, these machines involve a relatively high investment. Hence, small laboratories often choose to perform NIL copies in a more rudimentary and cheaper way. A new simple system is presented in this document. It is based on two devices which can be made in-house in plastic by using a 3D printer or in aluminum. Thus, the overall manufacturing complexity is vastly reduced. The presented system includes pressure control and potentially temperature control. Replicas have been made using a sawtooth grating master with a pitch around half micrometre. High quality patterns with low density of imperfections have been achieved in 2.25 cm2 surfaces. The material chosen for the negative intermediary mould is PDMS. Tests of the imprint have been performed using the commercial hybrid polymer Ormostamp®.

Bridging the gap between PAT concepts and implementation: An integrated software platform for fermentation.

PubMed

Chopda, Viki R; Gomes, James; Rathore, Anurag S

2016-01-01

Bioreactor control significantly impacts both the amount and quality of the product being manufactured. The complexity of the control strategy that is implemented increases with reactor size, which may vary from thousands to tens of thousands of litres in commercial manufacturing. The Process Analytical Technology (PAT) initiative has highlighted the need for having robust monitoring tools and effective control schemes that are capable of taking real time information about the critical quality attributes (CQA) and the critical process parameters (CPP) and executing immediate response as soon as a deviation occurs. However, the limited flexibility that present commercial software packages offer creates a hurdle. Visual programming environments have gradually emerged as potential alternatives to the available text based languages. This paper showcases development of an integrated programme using a visual programming environment for a Sartorius BIOSTAT® B Plus 5L bioreactor through which various peripheral devices are interfaced. The proposed programme facilitates real-time access to data and allows for execution of control actions to follow the desired trajectory. Major benefits of such integrated software system include: (i) improved real time monitoring and control; (ii) reduced variability; (iii) improved performance; (iv) reduced operator-training time; (v) enhanced knowledge management; and (vi) easier PAT implementation. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Manufacturing processes for fabricating graphite/PMR 15 polyimide structural elements

NASA Technical Reports Server (NTRS)

Sheppard, C. H.; Hoggatt, J. T.; Symonds, W. A.

1979-01-01

Investigations were conducted to obtain commercially available graphite/PMR-15 polyimide prepreg, develop an autoclave manufacturing process, and demonstrate the process by manufacturing structural elements. Controls were established on polymer, prepreg, composite fabrication, and quality assurance, Successful material quality control and processes were demonstrated by fabricating major structural elements including flat laminates, hat sections, I beam sections, honeycomb sandwich structures, and molded graphite reinforced fittings. Successful fabrication of structural elements and simulated section of the space shuttle aft body flap shows that the graphite/PMR-15 polyimide system and the developed processes are ready for further evaluation in flight test hardware.

Intelligent Manufacturing of Commercial Optics Final Report CRADA No. TC-0313-92

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, J. S.; Pollicove, H.

The project combined the research and development efforts of LLNL and the University of Rochester Center for Manufacturing Optics (COM), to develop a new generation of flexible computer controlled optics· grinding machines. COM's principal near term development effort is to commercialize the OPTICAM-SM, a new prototype spherical grinding machine. A crucial requirement for commercializing the OPTICAM-SM is the development of a predictable and repeatable material removal process ( deterministic micro-grinding) that yields high quality surfaces that minimize non-deterministic polishing. OPTICAM machine tools and the fabrication process development studies are part of COM' s response to the DOD (ARPA) request tomore » implement a modernization strategy for revitalizing the U.S. optics manufacturing base. This project was entered into in order to develop a new generation of :flexible, computer-controlled optics grinding machines.« less

A Quality Assurance Initiative for Commercial-Scale Production in High-Throughput Cryopreservation of Blue Catfish Sperm

PubMed Central

Hu, E; Liao, T. W.; Tiersch, T. R.

2013-01-01

Cryopreservation of fish sperm has been studied for decades at a laboratory (research) scale. However, high-throughput cryopreservation of fish sperm has recently been developed to enable industrial-scale production. This study treated blue catfish (Ictalurus furcatus) sperm high-throughput cryopreservation as a manufacturing production line and initiated quality assurance plan development. The main objectives were to identify: 1) the main production quality characteristics; 2) the process features for quality assurance; 3) the internal quality characteristics and their specification designs; 4) the quality control and process capability evaluation methods, and 5) the directions for further improvements and applications. The essential product quality characteristics were identified as fertility-related characteristics. Specification design which established the tolerance levels according to demand and process constraints was performed based on these quality characteristics. Meanwhile, to ensure integrity throughout the process, internal quality characteristics (characteristics at each quality control point within process) that could affect fertility-related quality characteristics were defined with specifications. Due to the process feature of 100% inspection (quality inspection of every fish), a specific calculation method, use of cumulative sum (CUSUM) control charts, was applied to monitor each quality characteristic. An index of overall process evaluation, process capacity, was analyzed based on in-control process and the designed specifications, which further integrates the quality assurance plan. With the established quality assurance plan, the process could operate stably and quality of products would be reliable. PMID:23872356

Effects of thinning on hydrology and water quality of a drained pine forest in coastal North Carolina

Treesearch

D.M. Amatya; R.W. Skaggs

2008-01-01

A study was conducted to examine the effects of commercial thinning on hydrology and water quality of a 28-year old (in 2002) drained loblolly pine (Pinus taeda L.) plantation watershed (D3) using another adjacent watershed (D1) as a control. A paired watershed approach was used with data from two periods (1988-90 and 2000-02) for calibration and data from 2002-07 as...

East Europe Report, Economic and Industrial Affairs

DTIC Science & Technology

1984-09-05

As. long as equipment to entrap sulfur dioxide from flue gases is not manufactured in this country, and fuels not desulfurized , or the fluidized...must coordinate, control and direct through the functional units the activities of commercial firms, directorates and offices in accordance with the...and other materials used in the production of goods with substandard indicators. 11 Particular attention has been paid to quality control personnel

Organizational Leadership and Adaptive Reserve in Blood Pressure Control: The Heart Health NOW Study.

PubMed

Henderson, Kamal H; DeWalt, Darren A; Halladay, Jacquie; Weiner, Bryan J; Kim, Jung I; Fine, Jason; Cykert, Samuel

2018-04-01

Our purpose was to assess whether a practice's adaptive reserve and high leadership capability in quality improvement are associated with population blood pressure control. We divided practices into quartiles of blood pressure control performance and considered the top quartile as the benchmark for comparison. Using abstracted clinical data from electronic health records, we performed a cross-sectional study to assess the association of top quartile hypertension control and (1) the baseline practice adaptive reserve (PAR) scores and (2) baseline practice leadership scores, using modified Poisson regression models adjusting for practice-level characteristics. Among 181 practices, 46 were in the top quartile, which averaged 68% or better blood pressure control. Practices with higher PAR scores compared with lower PAR scores were not more likely to reside in the top quartile of performance (prevalence ratio [PR] = 1.92 for highest quartile; 95% CI, 0.9-4.1). Similarly, high quality improvement leadership capability compared with lower capability did not predict better blood pressure control performance (PR = 0.94; 95% CI, 0.57-1.56). Practices with higher proportions of commercially insured patients were more likely than practices with lower proportions of commercially insured patients to have top quartile performance (37% vs 26%, P =.002), whereas lower proportions of the uninsured (8% vs 14%, P =.055) were associated with better performance. Our findings show that adaptive reserve and leadership capability in quality improvement implementation are not statistically associated with achieving top quartile practice-level hypertension control at baseline in the Heart Health NOW project. Our findings, however, may be limited by a lack of patient-related factors and small sample size to preclude strong conclusions. © 2018 Annals of Family Medicine, Inc.

Recycling of treated domestic effluent from an on-site wastewater treatment system for hydroponics.

PubMed

Oyama, N; Nair, J; Ho, G E

2005-01-01

An alternative method to conserve water and produce crops in arid regions is through hydroponics. Application of treated wastewater for hydroponics will help in stripping off nutrients from wastewater, maximising reuse through reduced evaporation losses, increasing control on quality of water and reducing risk of pathogen contamination. This study focuses on the efficiency of treated wastewater from an on-site aerobic wastewater treatment unit. The experiment aimed to investigate 1) nutrient reduction 2) microbial reduction and 3) growth rate of plants fed on wastewater compared to a commercial hydroponics medium. The study revealed that the chemical and microbial quality of wastewater after hydroponics was safe and satisfactory for irrigation and plant growth rate in wastewater hydroponics was similar to those grown in a commercial medium.

Country watch: Nicaragua.

PubMed

Pauw, J

1999-01-01

The Association of Workers for Education, Health and Social Integration (TESIS) works with commercial sex workers to control HIV and sexually transmitted diseases in Nicaragua through free condom distribution and education. Education includes group work, individual counseling, and demonstrations of correct condom use. Condoms are also distributed to the motels frequented by commercial sex workers. When the Condom Social Marketing (CSM) project in Central America started, it sold condoms of the same quality as the ones offered by TESIS; thus the condom donors reduced their donations, and in turn, TESIS lost its normal quota for free condom distribution. Because of this situation, TESIS dealt with a condom promotion scheme at a lower cost for the poorest women. Condom quality did not deteriorate as products only came with simpler packaging. TESIS fills the gap which CSM missed.

Evaluation of the lime-cooking and tortilla making properties of quality protein maize hybrids grown in Mexico.

PubMed

Serna-Saldivar, Sergio O; Amaya Guerra, Carlos A; Herrera Macias, Pedro; Melesio Cuellar, Jose L; Preciado Ortiz, Ricardo E; Terron Ibarra, Arturo D; Vazquez Carrillo, Gricelda

2008-09-01

Eleven experimental and three commercial white quality protein maize (QPM) hybrids and two regular endosperm controls were planted at Celaya, Guanajuato, Mexico with the aim of comparing grain physical characteristics, protein quality, lime-cooking and tortilla making properties. All genotypes were planted under irrigation using a density of 80,000 plants/ha and fertilized with 250 kg N-60 P-60 K per hectare. When compared with the controls these QPM genotypes had lower test (77.4 vs. 76.5 kg/hL) and 1,000 kernel weights (327 vs. 307 g), softer endosperm texture (2.5 vs. 1.8 where 1 = soft, 2 intermediate and 3 hard endosperm), lower protein (10.0 vs. 8.0%), higher nixtamal water uptake after 30 min lime-cooking (50.0 vs. 53.1% moisture) and lower pericarp removal scores. The lower thousand-kernel weight and softer endosperm texture observed in the QPM genotypes lowered the optimum lime-cooking time as estimated with regression equations. Most QPM genotypes had higher amounts of lysine, tryptophan and albumins/globulins when compared with the controls. QPMs HEC 424973, HEC 774986 and HEC 734286 had the best grain traits for nixtamalization and therefore the best potential for industrial utilization. The commercial use of these QPM hybrids should benefit Mexicans who depend on tortillas as the main staple.

[Correspondence analysis between traditional commercial specifications and quantitative quality indices of Notopterygii Rhizoma et Radix].

PubMed

Jiang, Shun-Yuan; Sun, Hong-Bing; Sun, Hui; Ma, Yu-Ying; Chen, Hong-Yu; Zhu, Wen-Tao; Zhou, Yi

2016-03-01

This paper aims to explore a comprehensive assessment method combined traditional Chinese medicinal material specifications with quantitative quality indicators. Seventy-six samples of Notopterygii Rhizoma et Radix were collected on market and at producing areas. Traditional commercial specifications were described and assigned, and 10 chemical components and volatile oils were determined for each sample. Cluster analysis, Fisher discriminant analysis and correspondence analysis were used to establish the relationship between the traditional qualitative commercial specifications and quantitative chemical indices for comprehensive evaluating quality of medicinal materials, and quantitative classification of commercial grade and quality grade. A herb quality index (HQI) including traditional commercial specifications and chemical components for quantitative grade classification were established, and corresponding discriminant function were figured out for precise determination of quality grade and sub-grade of Notopterygii Rhizoma et Radix. The result showed that notopterol, isoimperatorin and volatile oil were the major components for determination of chemical quality, and their dividing values were specified for every grade and sub-grade of the commercial materials of Notopterygii Rhizoma et Radix. According to the result, essential relationship between traditional medicinal indicators, qualitative commercial specifications, and quantitative chemical composition indicators can be examined by K-mean cluster, Fisher discriminant analysis and correspondence analysis, which provide a new method for comprehensive quantitative evaluation of traditional Chinese medicine quality integrated traditional commodity specifications and quantitative modern chemical index. Copyright© by the Chinese Pharmaceutical Association.

HoloHands: games console interface for controlling holographic optical manipulation

NASA Astrophysics Data System (ADS)

McDonald, C.; McPherson, M.; McDougall, C.; McGloin, D.

2012-10-01

The increased application of holographic optical manipulation techniques within the life sciences has sparked the development of accessible interfaces for control of holographic optical tweezers. Of particular interest are those that employ familiar, commercially available technologies. Here we present the use of a low cost games console interface, the Microsoft Kinect for the control of holographic optical tweezers and a study into the effect of using such a system upon the quality of trap generated.

Conceptual design studies of candidate V/STOL lift fan commercial short haul transport for 1980 - 1985 V/STOL lift fan study

NASA Technical Reports Server (NTRS)

Eldridge, W. M.; Ferrell, J. A.; Mckee, J. W.; Wayne, J. E., Jr.; Zabinsky, J. M.

1973-01-01

Conceptual designs of V/STOL lift fan commercial short haul transport aircraft for the 1980-85 time period were studied to determine their technical and economic feasibility. The engine concepts included both integral and remote fans. The scope of the study included definition of the hover control concept for each propulsion system, aircraft design, aircraft mass properties, cruise performance, noise and ride qualities evaluation. Economic evaluating was also studied on a basis of direct operating costs and route structure.

32 CFR 507.9 - Articles not authorized for manufacture or sale.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 3 2010-07-01 2010-07-01 true Articles not authorized for manufacture or sale... CIVIL AUTHORITIES AND PUBLIC RELATIONS MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Manufacture and Sale of Decorations...

32 CFR 507.8 - Articles authorized for manufacture and sale.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 3 2010-07-01 2010-07-01 true Articles authorized for manufacture and sale. 507... CIVIL AUTHORITIES AND PUBLIC RELATIONS MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Manufacture and Sale of Decorations...

Quality Control Analysis of Student-Generated Pharmaceutical Capsules

ERIC Educational Resources Information Center

Bucholtz, Ehren C.; French, Lisa M.; Lavoie, Jaie P.; Gaebelein, Claude J.

2010-01-01

Pharmacists, although not practicing chemists, often use skills and knowledge obtained in chemistry courses that are essential for success in their profession. This is especially apparent when preparing prescriptions for drugs that do not have a commercially available dosage form. Some well-publicized events indicate the potency of these drugs is…

32 CFR 507.11 - Reproduction of designs.

Code of Federal Regulations, 2012 CFR

2012-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.11 Reproduction of designs. (a) The photographing, printing, or, in any manner making or executing any engraving... 32 National Defense 3 2012-07-01 2009-07-01 true Reproduction of designs. 507.11 Section 507.11...

32 CFR 507.11 - Reproduction of designs.

Code of Federal Regulations, 2013 CFR

2013-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.11 Reproduction of designs. (a) The photographing, printing, or, in any manner making or executing any engraving... 32 National Defense 3 2013-07-01 2013-07-01 false Reproduction of designs. 507.11 Section 507.11...

32 CFR 507.11 - Reproduction of designs.

Code of Federal Regulations, 2014 CFR

2014-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.11 Reproduction of designs. (a) The photographing, printing, or, in any manner making or executing any engraving... 32 National Defense 3 2014-07-01 2014-07-01 false Reproduction of designs. 507.11 Section 507.11...

32 CFR 507.11 - Reproduction of designs.

Code of Federal Regulations, 2010 CFR

2010-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.11 Reproduction of designs. (a) The photographing, printing, or, in any manner making or executing any engraving... 32 National Defense 3 2010-07-01 2010-07-01 true Reproduction of designs. 507.11 Section 507.11...

32 CFR 507.11 - Reproduction of designs.

Code of Federal Regulations, 2011 CFR

2011-07-01

... HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Commercial Use of Heraldic Designs § 507.11 Reproduction of designs. (a) The photographing, printing, or, in any manner making or executing any engraving... 32 National Defense 3 2011-07-01 2009-07-01 true Reproduction of designs. 507.11 Section 507.11...

Solid anthropomorphic infant whole body DXA phantom: Design, evaluation, and multisite testing

USDA-ARS?s Scientific Manuscript database

Dual energy X-ray absorptiometry (DXA) requires phantoms for quality control and cross-calibration. No commercially available phantoms are designed specifically for infant whole-body scanning. We fabricated a phantom closely matching a 7-kg human infant in body habitus using PVC, nylon-mix, and poly...

Mapping of quantitative trait loci for butter content and hardness in cocoa beans (Theobroma cacao L.)

USDA-ARS?s Scientific Manuscript database

Cocoa butter is an important raw material for the chocolate, pharmaceutical, and cosmetic industries. The butter content and quality in cocoa beans are genetically controlled characteristics, and affect its commercial values and industrial applicability. In the present work, an F2 population derived...

Information Technology in Education: The Critical Lack of Principled Leadership.

ERIC Educational Resources Information Center

Maddux, Cleborne D.

2002-01-01

Suggests there is a crisis in educational leadership, especially as it affects information technology. Highlights include educational leaders as managers; the commercialization of education; management strategies on campus; students as customers; quality control, online distance education, and the business model; and the future of online distance…

48 CFR 46.202-1 - Contracts for commercial items.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 46.202-1 Contracts for commercial items... quality assurance systems as a substitute for Government inspection and testing before tender for...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mills, G.J.; Brown, G.G.; Waterman, D.D.

The feasibility of prestressing commercial boron/epoxy and graphite/epoxy prepreg material to higher strengths and lower property dispersions is demonstrated. Its practical application as an on-line process for improving quality levels is possible with minor modifications to current experimental practice. The mechanics of the bendstressing method affects a controlled alteration in the fiber defect content to the extent that composite improvements can be achieved approaching the inherent fiber quality with dispersions in properties reduced to the 1 to 2% range. (Author, modified-PL)

Effect of the use of a commercial phosphate mixture on selected quality characteristics of 2 Spanish-style dry-ripened sausages.

PubMed

Fonseca, Beatriz; Kuri, Victor; Zumalacárregui, José M; Fernández-Diez, Ana; Salvá, Bettit K; Caro, Irma; Osorio, M Teresa; Mateo, Javier

2011-01-01

The aim of this study was to evaluate the usefulness of the addition of a commercial phosphate mixture in 2 dry-ripened Spanish-style sausages: "salchichón" and "chorizo." Three batches of each of those sausages were prepared with low and high levels of phosphates, and selected quality variables (moisture, pH, a(w) , lactic and acetic acid, α-amino nitrogen, total free fatty acids, thiobarbituric acid reactive substances, microbial counts, color, and texture analysis) were compared against controls. Furthermore, phosphate-added and control sausages were ranked by consumers in order of preference. In "salchichón," phosphate addition resulted in a significant (P < 0.05) increase in drying rate, and tendencies (not significant) toward a decrease in lipid oxidation and an increase in hardness and chewiness. In "chorizo," the addition of phosphates resulted in higher hardness, elasticity and chewiness, and lower yellowness (P < 0.05). In the manufacture process of dry-ripened sausages, phosphates can be considered as additives with potential enhancement effect in drying and eating quality. The main outcome from the present study is to find evidence on which points of reference could be drawn for the technological application of phosphates in dry-ripened sausages. It has been observed that the drying rate and several eating quality characteristics can be enhanced with the use of phosphates. © 2011 Institute of Food Technologists®

Quality-control materials in the USDA National Food and Nutrient Analysis Program (NFNAP).

PubMed

Phillips, Katherine M; Patterson, Kristine Y; Rasor, Amy S; Exler, Jacob; Haytowitz, David B; Holden, Joanne M; Pehrsson, Pamela R

2006-03-01

The US Department of Agriculture (USDA) Nutrient Data Laboratory (NDL) develops and maintains the USDA National Nutrient Databank System (NDBS). Data are released from the NDBS for scientific and public use through the USDA National Nutrient Database for Standard Reference (SR) ( http://www.ars.usda.gov/ba/bhnrc/ndl ). In 1997 the NDL initiated the National Food and Nutrient Analysis Program (NFNAP) to update and expand its food-composition data. The program included: 1) nationwide probability-based sampling of foods; 2) central processing and archiving of food samples; 3) analysis of food components at commercial, government, and university laboratories; 4) incorporation of new analytical data into the NDBS; and 5) dissemination of these data to the scientific community. A key feature and strength of the NFNAP was a rigorous quality-control program that enabled independent verification of the accuracy and precision of analytical results. Custom-made food-control composites and/or commercially available certified reference materials were sent to the laboratories, blinded, with the samples. Data for these materials were essential to ongoing monitoring of analytical work, to identify and resolve suspected analytical problems, to ensure the accuracy and precision of results for the NFNAP food samples.

Meteorological Data Quality from Original Equipment Manufacturer (OEM) Sensors on Commercial Vehicles

NASA Astrophysics Data System (ADS)

Chang, C. H.; Pietras, J.; Heppner, P.; Evans, J. D.; Wang, J.

2016-12-01

The Mobile Platform Environmental Data (MoPED) system acquires real-time data on weather conditions from commercial fleet providers and provides them to the National Weather Service (NWS) for use in operations and numerical models. The MoPED system assesses the quality of these data by comparing them to observations from airport weather stations when the mobile platforms are in sufficiently close proximity (in space and time). We have devised a set of quality control algorithms that are applied to vehicle observation datasets to qualify them for dissemination to NWS. Commercial vehicles participating in MoPED have a third-party suite of sensors for ambient air temperature, relative humidity, light level, precipitation intensity, atmospheric pressure, ozone, and road temperature. In addition, some vehicles also generate meteorological data from sensors built into the vehicles themselves (original equipment manufacturer (OEM) sensors) which conform to the SAE J1939 standard for onboard vehicle networking. These sensors, known as OEM J-data sensors, measure numerous parameters associated with emissions control and engine performance - including ambient air temperature and atmospheric pressure. Time-tagged and transmitted to the MoPED system, these OEM J-data measurements can be a tremendous source of weather data for NWS if they can be extracted and communicated in real-time from the vehicles. We are working with a commercial fleet (who have OEM J-data available) to determine suitability of these data for NWS. To ensure the overall quality of the data, we have developed a methodology for assessing the suitability of classes of vehicles and sensors for inclusion in the MoPED dissemination, for the continued assessment of individual vehicles once their class has been accepted into MoPED, and for identifying corrective measures (such as adjusting measurements to correct for individual sensor offsets). A byproduct of that methodology is a multi-component model for sources of errors in mobile meteorological data measurements. We describe this error model, and provide examples of studies of candidate OEM J-data vehicle fleets in which we measured or compensated for various components of the error model.

RESULTS OF THE CANADIAN POTATO IRRADIATION PROGRAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hetherington, C.H.; MacQueen, K.F.

1963-01-01

Results of test irradiations of potatoes in Canada between October 1961 and March 1962 are reviewed. Completely effective sprout inhibition was obtained in all cases. Radiation treatment was observed to be more effective than other methods. A lower dosage level would probably be satisfactory on a commercial basis. There was no internal sprouting and irradiated potatoes remained firmer than controls. Some dry rot was present in both control and treated potatoes. Irradiated potatoes were found to be more resistant to light greening. The quality of chips, instant mashed potatoes, frozen French fries, and fresh boilers produced from irradiated potatoes wasmore » found to be good. Implications and plans for commercialization of the process are discussed. (H.M.G.)« less

Protection induced by a commercial bivalent vaccine against Foot-and-Mouth Disease 2010 field virus from Ecuador.

PubMed

Duque, Hernando; Naranjo, Jose; Carrillo, Consuelo; Burbano, Alexandra; Vargas, Javier; Pauszek, Lisa; Olesen, Ian; Sanchez-Vazquez, Manuel J; Cosivi, Ottorino; Allende, Rossana M

2016-07-29

Foot-and-Mouth Disease serotype O circulated endemically in Ecuador for many years, with an upsurge occurring in 2009. This manuscript describes retrospectively in vitro and in vivo laboratory studies to predict the field effectiveness of a commercial FMD vaccine to protect against the field strain, and explains the key actions and epidemiological strategies followed by the country to control the disease. The results established that the use of a good quality oil vaccine, manufactured with strains that were isolated long ago: O1 Campos Br/58 and A24 Cruzeiro Br/55; combined with the correct epidemiological strategies, are useful to control field strains when used in periodic biannual vaccination campaigns. Published by Elsevier Ltd.

Relationship between influence function accuracy and polishing quality in magnetorheological finishing

NASA Astrophysics Data System (ADS)

Schinhaerl, Markus; Schneider, Florian; Rascher, Rolf; Vogt, Christian; Sperber, Peter

2010-10-01

Magnetorheological finishing is a typical commercial application of a computer-controlled polishing process in the manufacturing of precision optical surfaces. Precise knowledge of the material removal characteristic of the polishing tool (influence function) is essential for controlling the material removal on the workpiece surface by the dwell time method. Results from the testing series with magnetorheological finishing have shown that a deviation of only 5% between the actual material removal characteristic of the polishing tool and that represented by the influence function caused a considerable reduction in the polishing quality. The paper discusses reasons for inaccuracies in the influence function and the effects on the polishing quality. The generic results of this research serve for the development of improved polishing strategies, and may be used in alternative applications of computer-controlled polishing processes that quantify the material removal characteristic by influence functions.

Design requirements for SRB production control system. Volume 3: Package evaluation, modification and hardware

NASA Technical Reports Server (NTRS)

1981-01-01

The software package evaluation was designed to analyze commercially available, field-proven, production control or manufacturing resource planning management technology and software package. The analysis was conducted by comparing SRB production control software requirements and conceptual system design to software package capabilities. The methodology of evaluation and the findings at each stage of evaluation are described. Topics covered include: vendor listing; request for information (RFI) document; RFI response rate and quality; RFI evaluation process; and capabilities versus requirements.

Quality parameters and RAPD-PCR differentiation of commercial baker's yeast and hybrid strains.

PubMed

El-Fiky, Zaki A; Hassan, Gamal M; Emam, Ahmed M

2012-06-01

Baker's yeast, Saccharomyces cerevisiae, is a key component in bread baking. Total of 12 commercial baker's yeast and 2 hybrid strains were compared using traditional quality parameters. Total of 5 strains with high leavening power and the 2 hybrid strains were selected and evaluated for their alpha-amylase, maltase, glucoamylase enzymes, and compared using random amplified polymorphic DNA (RAPD). The results revealed that all selected yeast strains have a low level of alpha-amylase and a high level of maltase and glucoamylase enzymes. Meanwhile, the Egyptian yeast strain (EY) had the highest content of alpha-amylase and maltase enzymes followed by the hybrid YH strain. The EY and YH strains have the highest content of glucoamylase enzyme almost with the same level. The RAPD banding patterns showed a wide variation among commercial yeast and hybrid strains. The closely related Egyptian yeast strains (EY and AL) demonstrated close similarity of their genotypes. The 2 hybrid strains were clustered to Turkish and European strains in 1 group. The authors conclude that the identification of strains and hybrids using RAPD technique was useful in determining their genetic relationship. These results can be useful not only for the basic research, but also for the quality control in baking factories. © 2012 Institute of Food Technologists®

Intermittent slow sand filtration for preventing diarrhoea among children in Kenyan households using unimproved water sources: randomized controlled trial.

PubMed

Tiwari, Sangya-Sangam K; Schmidt, Wolf-Peter; Darby, Jeannie; Kariuki, Z G; Jenkins, Marion W

2009-11-01

Measure effectiveness of intermittent slow sand filtration for reducing child diarrhoea among households using unimproved water sources in rural Kenya. A randomized controlled trail was conducted among populations meeting a high-risk profile for child diarrhoea from drinking river water in the River Njoro watershed. Intervention households (30) were provided the concrete BioSand Filter and instructed on filter use and maintenance. Control households (29) continued normal practices. Longitudinal monthly monitoring of diarrhoea (seven-day daily prevalence recall) and of influent, effluent, and drinking water quality for fecal coliform was conducted for 6 months. Intervention households had better drinking water quality than control households (fecal coliform geometric mean, 30.0 CFU vs. 89.0 CFU/100 ml, P < 0.001) and reported significantly fewer diarrhoea days (86 days over 626 child-weeks) compared to controls (203 days over 558 child-weeks) among children up to 15 (age-adjusted RR 0.46; 95 % CI = 0.22, 0.96). Greater child diarrhoea reduction due to the intervention (age-adjusted RR 0.23, 95 % CI = 0.10, 0.51) was observed among the sub-group using unimproved water sources all of the time. Intermittent slow sand filtration, a non-commercial technology, produces similar observed effects on child diarrhoea as commercial POU products, adding to the range of effective options for poor populations (chlorination, ceramic filtration, solar disinfection, flocculation/disinfection).

Lead contamination in Eugenia dyeriana herbal preparations from different commercial sources in Malaysia.

PubMed

Ang, H H

2008-06-01

The Drug Control Authority (DCA) of Malaysia implemented the phase three registration of traditional medicines on 1 January, 1992. A total of 100 products in various pharmaceutical dosage forms of a herbal preparation, containing Eugenia dyeriana, either single or combined preparations (more than one medicinal plant), were analyzed for the presence of lead contamination, using atomic absorption spectrophotometry. These samples were bought from different commercial sources in the Malaysian market, after performing a simple random sampling. Results showed that 22% of the above products failed to comply with the quality requirement for traditional medicines in Malaysia. Although this study showed that 78% of the products fully complied with the quality requirement for traditional medicines in Malaysia pertaining to lead, however, they cannot be assumed safe from lead contamination because of batch-to-batch inconsistency.

Control Reallocation Strategies for Damage Adaptation in Transport Class Aircraft

NASA Technical Reports Server (NTRS)

Gundy-Burlet, Karen; Krishnakumar, K.; Limes, Greg; Bryant, Don

2003-01-01

This paper examines the feasibility, potential benefits and implementation issues associated with retrofitting a neural-adaptive flight control system (NFCS) to existing transport aircraft, including both cable/hydraulic and fly-by-wire configurations. NFCS uses a neural network based direct adaptive control approach for applying alternate sources of control authority in the presence of damage or failures in order to achieve desired flight control performance. Neural networks are used to provide consistent handling qualities across flight conditions, adapt to changes in aircraft dynamics and to make the controller easy to apply when implemented on different aircraft. Full-motion piloted simulation studies were performed on two different transport models: the Boeing 747-400 and the Boeing C-17. Subjects included NASA, Air Force and commercial airline pilots. Results demonstrate the potential for improving handing qualities and significantly increased survivability rates under various simulated failure conditions.

Offset Printing Plate Quality Sensor on a Low-Cost Processor

PubMed Central

Poljak, Jelena; Botella, Guillermo; García, Carlos; Poljaček, Sanja Mahović; Prieto-Matías, Manuel; Tirado, Francisco

2013-01-01

The aim of this work is to develop a microprocessor-based sensor that measures the quality of the offset printing plate through the introduction of different image analysis applications. The main features of the presented system are the low cost, the low amount of power consumption, its modularity and easy integration with other industrial modules for printing plates, and its robustness against noise environments. For the sake of clarity, a viability analysis of previous software is presented through different strategies, based on dynamic histogram and Hough transform. This paper provides performance and scalability data compared with existing costly commercial devices. Furthermore, a general overview of quality control possibilities for printing plates is presented and could be useful to a system where such controls are regularly conducted. PMID:24284766

Easy parallel screening of reagent stability, quality control, and metrology in solid phase peptide synthesis (SPPS) and peptide couplings for microarrays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Achyuthan, Komandoor E.; Wheeler, David R.

Evaluating the stability of coupling reagents, quality control (QC), and surface functionalization metrology are all critical to the production of high quality peptide microarrays. We describe a broadly applicable screening technique for evaluating the fidelity of solid phase peptide synthesis (SPPS), the stability of activation/coupling reagents, and a microarray surface metrology tool. This technique was used to assess the stability of the activation reagent 1-{[1-(Cyano-2-ethoxy-2-oxo-ethylidenaminooxy)dimethylamino-morpholinomethylene]}methaneaminiumHexafluorophosphate (COMU) (Sigma-Aldrich, St. Louis, MO, USA) by SPPS of Leu-Enkephalin (YGGFL) or the coupling of commercially synthesized YGGFL peptides to (3-aminopropyl)triethyoxysilane-modified glass surfaces. Coupling efficiency was quantitated by fluorescence signaling based on immunoreactivity of themore » YGGFL motif. It was concluded that COMU solutions should be prepared fresh and used within 5 h when stored at ~23 °C and not beyond 24 h if stored refrigerated, both in closed containers. Caveats to gauging COMU stability by absorption spectroscopy are discussed. Commercial YGGFL peptides needed independent QC, due to immunoreactivity variations for the same sequence synthesized by different vendors. This technique is useful in evaluating the stability of other activation/coupling reagents besides COMU and as a metrology tool for SPPS and peptide microarrays.« less

Easy parallel screening of reagent stability, quality control, and metrology in solid phase peptide synthesis (SPPS) and peptide couplings for microarrays

DOE PAGES

Achyuthan, Komandoor E.; Wheeler, David R.

2015-08-27

Evaluating the stability of coupling reagents, quality control (QC), and surface functionalization metrology are all critical to the production of high quality peptide microarrays. We describe a broadly applicable screening technique for evaluating the fidelity of solid phase peptide synthesis (SPPS), the stability of activation/coupling reagents, and a microarray surface metrology tool. This technique was used to assess the stability of the activation reagent 1-{[1-(Cyano-2-ethoxy-2-oxo-ethylidenaminooxy)dimethylamino-morpholinomethylene]}methaneaminiumHexafluorophosphate (COMU) (Sigma-Aldrich, St. Louis, MO, USA) by SPPS of Leu-Enkephalin (YGGFL) or the coupling of commercially synthesized YGGFL peptides to (3-aminopropyl)triethyoxysilane-modified glass surfaces. Coupling efficiency was quantitated by fluorescence signaling based on immunoreactivity of themore » YGGFL motif. It was concluded that COMU solutions should be prepared fresh and used within 5 h when stored at ~23 °C and not beyond 24 h if stored refrigerated, both in closed containers. Caveats to gauging COMU stability by absorption spectroscopy are discussed. Commercial YGGFL peptides needed independent QC, due to immunoreactivity variations for the same sequence synthesized by different vendors. This technique is useful in evaluating the stability of other activation/coupling reagents besides COMU and as a metrology tool for SPPS and peptide microarrays.« less

Extending the shelf life of edible flowers with controlled release of 1-methylcyclopropene and modified atmosphere packaging.

PubMed

Kou, Liping; Turner, Ellen R; Luo, Yaguang

2012-05-01

Edible flowers have great sensory appeal, but their extremely short shelf life limits their commercial usage. Postharvest 1-methylcyclopropene (1-MCP) treatment is used to counter ethylene activity and delay senescence in fresh produce; however, its potential application in edible flowers has not been tested. The objective of this study was to investigate the effect of 1-MCP treatment with modified atmosphere packaging (MAP) on the shelf life of edible flowers. Freshly harvested carnations and snapdragons were packaged in trays with or without 0.5 μL/L of 1-MCP, sealed with a gas permeable film, and stored at 5 °C. Package atmospheres, tissue electrolyte leakage, and flower quality were evaluated on days 0, 7, and 14. Treatment with 1-MCP resulted in significantly slower changes in package headspace O(2), CO(2), and C(2)H(4) partial pressures, maintained higher overall quality of both flower species and reduced electrolyte leakage and abscission in snapdragon. All samples prepared with MAP had significantly reduced dehydration and higher overall quality compared to flowers packaged commercially in plastic clamshell containers. Treatments with controlled release of 1-MCP and MAP significantly extended storage life of edible carnation and snapdragon flowers. © 2012 Institute of Food Technologists®

A practical discussion of risk management for manufacturing of pharmaceutical products.

PubMed

Mollah, A Hamid; Baseman, Harold S; Long, Mike; Rathore, Anurag S

2014-01-01

Quality risk management (QRM) is now a regulatory expectation, and it makes good business sense. The goal of the risk assessment is to increase process understanding and deliver safe and effective product to the patients. Risk analysis and management is an acceptable and effective way to minimize patient risk and determine the appropriate level of controls in manufacturing. While understanding the elements of QRM is important, knowing how to apply them in the manufacturing environment is essential for effective process performance and control. This article will preview application of QRM in pharmaceutical and biopharmaceutical manufacturing to illustrate how QRM can help the reader achieve that objective. There are several areas of risk that a drug company may encounter in pharmaceutical manufacturing, specifically addressing oral solid and liquid formulations. QRM tools can be used effectively to identify the risks and develop strategy to minimize or control them. Risks are associated throughout the biopharmaceutical manufacturing process-from raw material supply through manufacturing and filling operations to final distribution via a controlled cold chain process. Assessing relevant attributes and risks for biotechnology-derived products is more complicated and challenging for complex pharmaceuticals. This paper discusses key risk factors in biopharmaceutical manufacturing. Successful development and commercialization of pharmaceutical products is all about managing risks. If a company was to take zero risk, most likely the path to commercialization would not be commercially viable. On the other hand, if the risk taken was too much, the product is likely to have a suboptimal safety and efficacy profile and thus is unlikely to be a successful product. This article addresses the topic of quality risk management with the key objective of minimizing patient risk while creating an optimal process and product. Various tools are presented to aid implementation of these concepts. © PDA, Inc. 2014.

HPTLC Fingerprint Analysis: A Quality Control for Authentication of Herbal Phytochemicals

NASA Astrophysics Data System (ADS)

Ram, Mauji; Abdin, M. Z.; Khan, M. A.; Jha, Prabhakar

Authentication and consistent quality are the basic requirement for Indian traditional medicine (TIM), Chinese traditional herbal medicine (TCHM), and their commercial products, regardless of the kind of research conducted to modernize the TIM and TCHM. The complexities of TIM and TCHM challenge the current official quality control mode, for which only a few biochemical markers were selected for identification and quantitative assay. Referring too many unknown factors existed in TIM and TCHM, it is impossible and unnecessary to pinpoint qualitatively and quantitatively every single component contained in the herbal drug. Chromatographic fingerprint is a rational option to meet the need for more effective and powerful quality assessment to TIM and TCHM. The optimized chromatographic fingerprint is not only an alternative analytical tool for authentication, but also an approach to express the various pattern of chemical ingredients distribution in the herbal drugs and preserve such "database" for further multifaced sustainable studies. Analytical separation techniques, for example, high-performance liquid chromatography (HPLC), gas chromatography (GC) and mass spectrometry (MS) were among the most popular methods of choice used for quality control of raw material and finished herbal product. Fingerprint analysis approach using high-performance thin-layer chromatography (HPTLC) has become the most potent tool for quality control of herbal medicines because of its simplicity and reliability. It can serve as a tool for identification, authentication, and quality control of herbal drugs. In this chapter, attempts are being made to expand the use of HPTLC and at the same time create interest among prospective researcher in herbal analysis. The developed method can be used as a quality control tool for rapid authentication from a wide variety of herbal samples. Some examples demonstrated the role of fingerprinting in quality control and assessment.

Layered Manufacturing: Challenges and Opportunities

DTIC Science & Technology

2003-04-01

quality of the surface finish, eliminating residual stress , controlling local composition and microstructure, achieving fine feature size and...applications. Some methods have achieved commercial status, having graduated from the university level, others are in various stages of research. However...Road * Sintering * Co-firing * Shrinkage * Gas dimensions + Powder or + Resin * Residual stress precursors * Layer wire feeding infiltration * Distortion

Mapping loci that control tuber and foliar symptoms caused by PVY in Autotetraploid Potato (Solanum tuberosum L.)

USDA-ARS?s Scientific Manuscript database

Potato tuber necrotic ringspot disease (PTNRD) is a tuber deformity associated with infection by the tuber necrotic strain of Potato virus Y (PVYNTN). PTNRD negatively impacts tuber quality and marketability and poses a serious threat to seed and commercial potato production worldwide. PVYNTN symp...

Humans Do It Better: Inside the Open Directory Project.

ERIC Educational Resources Information Center

Sherman, Chris

2000-01-01

Explains the Open Directory Project (ODP), an attempt to catalog the World Wide Web by creating a human-compiled Web directory. Discusses the history of the project; open source models; the use of volunteer editors; quality control; problems and complaints; and use of ODP data by commercial services such as Google. (LRW)

Silviculture of the mahogany forest of Quintana Roo, Mexico: criteria and recommendations

Treesearch

P. ​​Negreros-Castillo; L. Camara-Cabrales; MS Devall; Mary Ann Fajvan; M.A. Mendoza Briseno; C.W. Mize; A. Navarro-Martinez

2014-01-01

Silviculture is the art, science and practice of controlling the establishment, composition, health, quality and growth of forests to accomplish a set of management objectives. This publication offers an approach to silviculture of the forests of Quintana Roo in which mahogany (Swietenia macrophylla King), the commercially most important tree...

Navigating sticky areas in transdermal product development.

PubMed

Strasinger, Caroline; Raney, Sam G; Tran, Doanh C; Ghosh, Priyanka; Newman, Bryan; Bashaw, Edward D; Ghosh, Tapash; Shukla, Chinmay G

2016-07-10

The benefits of transdermal delivery over the oral route to combat such issues of low bioavailability and limited controlled release opportunities are well known and have been previously discussed by many in the field (Prausnitz et al. (2004) [1]; Hadgraft and Lane (2006) [2]). However, significant challenges faced by developers as a product moves from the purely theoretical to commercial production have hampered full capitalization of the dosage forms vast benefits. While different technical aspects of transdermal system development have been discussed at various industry meetings and scientific workshops, uncertainties have persisted regarding the pharmaceutical industry's conventionally accepted approach for the development and manufacturing of transdermal systems. This review provides an overview of the challenges frequently faced and the industry's best practices for assuring the quality and performance of transdermal delivery systems and topical patches (collectively, TDS). The topics discussed are broadly divided into the evaluation of product quality and the evaluation of product performance; with the overall goal of the discussion to improve, advance and accelerate commercial development in the area of this complex controlled release dosage form. Published by Elsevier B.V.

California hospital networks are narrower in Marketplace than in commercial plans, but access and quality are similar.

PubMed

Haeder, Simon F; Weimer, David L; Mukamel, Dana B

2015-05-01

Do insurance plans offered through the Marketplace implemented by the State of California under the Affordable Care Act restrict consumers' access to hospitals relative to plans offered on the commercial market? And are the hospitals included in Marketplace networks of lower quality compared to those included in the commercial plans? To answer these questions, we analyzed differences in hospital networks across similar plan types offered both in the Marketplace and commercially, by region and insurer. We found that the common belief that Marketplace plans have narrower networks than their commercial counterparts appears empirically valid. However, there does not appear to be a substantive difference in geographic access as measured by the percentage of people residing in at least one hospital market area. More surprisingly, depending on the measure of hospital quality employed, the Marketplace plans have networks with comparable or even higher average quality than the networks of their commercial counterparts. Project HOPE—The People-to-People Health Foundation, Inc.

Ultrafast gas chromatography method with direct injection for the quantitative determination of benzene, toluene, ethylbenzene, and xylenes in commercial gasoline.

PubMed

Miranda, Nahieh Toscano; Sequinel, Rodrigo; Hatanaka, Rafael Rodrigues; de Oliveira, José Eduardo; Flumignan, Danilo Luiz

2017-04-01

Benzene, toluene, ethylbenzene, and xylenes are some of the most hazardous constituents found in commercial gasoline samples; therefore, these components must be monitored to avoid toxicological problems. We propose a new routine method of ultrafast gas chromatography coupled to flame ionization detection for the direct determination of benzene, toluene, ethylbenzene, and xylenes in commercial gasoline. This method is based on external standard calibration to quantify each compound, including the validation step of the study of linearity, detection and quantification limits, precision, and accuracy. The time of analysis was less than 3.2 min, with quantitative statements regarding the separation and quantification of all compounds in commercial gasoline samples. Ultrafast gas chromatography is a promising alternative method to official analytical techniques. Government laboratories could consider using this method for quality control. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Selected physical and chemical properties of Feverfew (Tanacetum parthenium) extracts important for formulated product quality and performance.

PubMed

Jin, Ping; Madieh, Shadi; Augsburger, Larry L

2008-01-01

The objectives of this research are: (1) to assess selected formulation-relevant physical properties of several commercial Feverfew extracts, including flowability, hygroscopicity, compressibility and compactibility (2) to develop and validate a suitable extraction method and HPLC assay, and (3) to determine the parthenolide content of several commercial Feverfew extracts. Carr's index, minimum orifice diameter and particle-particle interaction were used to evaluate powder flowability. Hygroscopicity was evaluated by determining the equilibrium moisture content (EMC) after storage at various % relative humidities. Heckle analysis and compression pressure-radial tensile strength relationship were used to represent compression and compaction properties of feverfew extracts. An adapted analytical method was developed based on literature methods and then validated for the determination of parthenolide in feverfew. The commercial extracts tested exhibited poor to very poor flowability. The comparatively low mean yield pressure suggested that feverfew extracts deformed mainly plastically. Hygroscopicity and compactibility varied greatly with source. No commercial feverfew extracts tested contained the label claimed parthenolide. Even different batches from the same manufacturer showed significantly different parthenolide content. Therefore, extract manufactures should commit to proper quality control procedures that ensure accurate label claims, and supplement manufacturers should take into account possible differences in physico-chemical properties when using extracts from multiple suppliers.

Commutability of control materials for external quality assessment of serum apolipoprotein A-I measurement.

PubMed

Zeng, Jie; Qi, Tianqi; Wang, Shu; Zhang, Tianjiao; Zhou, Weiyan; Zhao, Haijian; Ma, Rong; Zhang, Jiangtao; Yan, Ying; Dong, Jun; Zhang, Chuanbao; Chen, Wenxiang

2018-04-25

The aim of the current study was to evaluate the commutability of commercial control materials and human serum pools and to investigate the suitability of the materials for the external quality assessment (EQA) of serum apolipoprotein A-I (apo A-I) measurement. The Clinical and Laboratory Standards Institute (CLSI) EP14-A3 protocol was used for the commutability study. Apo A-I concentrations in two levels of commercial control materials used in EQA program, two fresh-frozen human serum pools (FSPs) and two frozen human serum pools prepared from residual clinical specimens (RSPs) were measured along with 50 individual samples using nine commercial assays. Measurement results of the 50 individual samples obtained with different assays were pairwise analyzed by Deming regression, and 95% prediction intervals (PIs) were calculated. The commutability of the processed materials was evaluated by comparing the measurement results of the materials with the limits of the PIs. The FSP-1 was commutable for all the 36 assay pairs, and FSP-2 was commutable for 30 pairs; RSP-1 and RSP-2 showed commutability for 27/36 and 22/36 assay pairs, respectively, whereas the two EQA materials were commutable only for 4/36 and 5/36 assay pairs, respectively. Non-commutability of the tested EQA materials has been observed among current apo A-I assays. EQA programs need either to take into account the commutability-related biases in the interpretation of the EQA results or to use more commutable materials. Frozen human serum pools were commutable for most of the assays.

Long-term quality assurance of [(18)F]-fluorodeoxyglucose (FDG) manufacturing.

PubMed

Gaspar, Ludovit; Reich, Michal; Kassai, Zoltan; Macasek, Fedor; Rodrigo, Luis; Kruzliak, Peter; Kovac, Peter

2016-01-01

Nine years of experience with 2286 commercial synthesis allowed us to deliver comprehensive information on the quality of (18)F-FDG production. Semi-automated FDG production line using Cyclone 18/9 machine (IBA Belgium), TRACERLab MXFDG synthesiser (GE Health, USA) using alkalic hydrolysis, grade "A" isolator with dispensing robotic unit (Tema Sinergie, Italy), and automatic control system under GAMP5 (minus2, Slovakia) was assessed by TQM tools as highly reliable aseptic production line, fully compliant with Good Manufacturing Practice and just-in-time delivery of FDG radiopharmaceutical. Fluoride-18 is received in steady yield and of very high radioactive purity. Synthesis yields exhibited high variance connected probably with quality of disposable cassettes and chemicals sets. Most performance non-conformities within the manufacturing cycle occur at mechanical nodes of dispensing unit. The long-term monitoring of 2286 commercial synthesis indicated high reliability of automatic synthesizers. Shewhart chart and ANOVA analysis showed that minor non-compliances occurred were mostly caused by the declinations of less experienced staff from standard operation procedures, and also by quality of automatic cassettes. Only 15 syntheses were found unfinished and in 4 cases the product was out-of-specification of European Pharmacopoeia. Most vulnerable step of manufacturing was dispensing and filling in grade "A" isolator. Its cleanliness and sterility was fully controlled under the investigated period by applying hydrogen peroxide vapours (VHP). Our experience with quality assurance in the production of [(18)F]-fluorodeoxyglucose (FDG) at production facility of BIONT based on TRACERlab MXFDG production module can be used for bench-marking of the emerging manufacturing and automated manufacturing systems.

Long-term quality assurance of [18F]-fluorodeoxyglucose (FDG) manufacturing

PubMed Central

Gaspar, Ludovit; Reich, Michal; Kassai, Zoltan; Macasek, Fedor; Rodrigo, Luis; Kruzliak, Peter; Kovac, Peter

2016-01-01

Nine years of experience with 2286 commercial synthesis allowed us to deliver comprehensive information on the quality of 18F-FDG production. Semi-automated FDG production line using Cyclone 18/9 machine (IBA Belgium), TRACERLab MXFDG synthesiser (GE Health, USA) using alkalic hydrolysis, grade “A” isolator with dispensing robotic unit (Tema Sinergie, Italy), and automatic control system under GAMP5 (minus2, Slovakia) was assessed by TQM tools as highly reliable aseptic production line, fully compliant with Good Manufacturing Practice and just-in-time delivery of FDG radiopharmaceutical. Fluoride-18 is received in steady yield and of very high radioactive purity. Synthesis yields exhibited high variance connected probably with quality of disposable cassettes and chemicals sets. Most performance non-conformities within the manufacturing cycle occur at mechanical nodes of dispensing unit. The long-term monitoring of 2286 commercial synthesis indicated high reliability of automatic synthesizers. Shewhart chart and ANOVA analysis showed that minor non-compliances occurred were mostly caused by the declinations of less experienced staff from standard operation procedures, and also by quality of automatic cassettes. Only 15 syntheses were found unfinished and in 4 cases the product was out-of-specification of European Pharmacopoeia. Most vulnerable step of manufacturing was dispensing and filling in grade “A” isolator. Its cleanliness and sterility was fully controlled under the investigated period by applying hydrogen peroxide vapours (VHP). Our experience with quality assurance in the production of [18F]-fluorodeoxyglucose (FDG) at production facility of BIONT based on TRACERlab MXFDG production module can be used for bench-marking of the emerging manufacturing and automated manufacturing systems. PMID:27508102

Space Age Training

NASA Technical Reports Server (NTRS)

1996-01-01

Teledyne Brown developed a computer-based interactive multimedia training system for use with the Crystal Growth Furnace in the U.S. Microgravity Laboratory-2 mission on the Space Shuttle. Teledyne Brown commercialized the system and customized it for PPG Industries Aircraft Products. The system challenges learners with role-playing scenarios and software-driven simulations engaging all the senses using text, video, animation, voice, sounds and music. The transfer of this technology to commercial industrial process training has resulted in significant improvements in effectiveness, standardization, and quality control, as well as cost reductions over the usual classroom and on-the- job training approaches.

Quality of cucumbers commercially fermented in calcium chloride brine without sodium salts

USDA-ARS?s Scientific Manuscript database

Commercial cucumber fermentation produces large volumes of salty wastewater. This study evaluated the quality of fermented cucumbers produced commercially using an alternative calcium chloride brining process. Fermentation conducted in calcium brines (0.1M calcium chloride, 6mM potassium sorbate, eq...

Effect of Self-efficacy Intervention on Quality of Life of Patients With Intestinal Stoma.

PubMed

Xu, Shujuan; Zhang, Zhiyun; Wang, Aimei; Zhu, Jiangyun; Tang, Hongzhi; Zhu, Xiaoli

2017-07-19

Colorectal carcinoma is one of the most common malignancies worldwide and the most prevalent cause of cancer mortality in China. The Miles operation and permanent colostomy are effective treatment. However, these affect the quality of life of patients as they alter normal defecation. Self-efficacy is used to define an individuals' assessments of their ability to perform a specific behavior successfully. It is regarded as an important belief that can predict health behaviors. The aim of this study was to explore the effect of a self-efficacy intervention on the quality of life of patients with a permanent colostomy. Forty-eight patients in treatment for permanent colostomy surgery were divided into the control and intervention groups. The control group received routine nursing; the intervention group was exposed to a 3-month self-efficacy intervention, as well as routine nursing. The two groups completed the Chinese version of a self-efficacy questionnaire at 10 days, 1 month, and 3 months after surgery. Three months after surgery, the two groups also completed a quality-of-life questionnaire. There were significant differences in the quality of life between the two groups. The self-efficacy intervention nursing method improved self-efficacy and the quality of life of patients with intestinal stoma and is worthy of clinical utilization and application.This is an open-access article distributed under the terms of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal.

Feasibility study of transmission of OTV camera control information in the video vertical blanking interval

NASA Technical Reports Server (NTRS)

White, Preston A., III

1994-01-01

The Operational Television system at Kennedy Space Center operates hundreds of video cameras, many remotely controllable, in support of the operations at the center. This study was undertaken to determine if commercial NABTS (North American Basic Teletext System) teletext transmission in the vertical blanking interval of the genlock signals distributed to the cameras could be used to send remote control commands to the cameras and the associated pan and tilt platforms. Wavelength division multiplexed fiberoptic links are being installed in the OTV system to obtain RS-250 short-haul quality. It was demonstrated that the NABTS transmission could be sent over the fiberoptic cable plant without excessive video quality degradation and that video cameras could be controlled using NABTS transmissions over multimode fiberoptic paths as long as 1.2 km.

Using spacecraft trace contaminant control systems to cure sick building syndrome

NASA Technical Reports Server (NTRS)

Graf, John C.

1994-01-01

Many residential and commercial buildings with centralized, recirculating, heating ventilation and air conditioning systems suffer from 'Sick Building Syndrome.' Ventilation rates are reduced to save energy costs, synthetic building materials off-gas contaminants, and unsafe levels of volatile organic compounds (VOC's) accumulate. These unsafe levels of contaminants can cause irritation of eyes and throat, fatigue and dizziness to building occupants. Increased ventilation, the primary method of treating Sick Building Syndrome is expensive (due to increased energy costs) and recently, the effectiveness of increased ventilation has been questioned. On spacecraft venting is not allowed, so the primary methods of air quality control are; source control, active filtering, and destruction of VOC's. Four non-venting contaminant removal technologies; strict material selection to provide source control, ambient temperature catalytic oxidation, photocatalytic oxidation, and uptake by higher plants, may have potential application for indoor air quality control.

Automated standardization technique for an inductively-coupled plasma emission spectrometer

USGS Publications Warehouse

Garbarino, John R.; Taylor, Howard E.

1982-01-01

The manifold assembly subsystem described permits real-time computer-controlled standardization and quality control of a commercial inductively-coupled plasma atomic emission spectrometer. The manifold assembly consists of a branch-structured glass manifold, a series of microcomputer-controlled solenoid valves, and a reservoir for each standard. Automated standardization involves selective actuation of each solenoid valve that permits a specific mixed standard solution to be pumped to the nebulizer of the spectrometer. Quality control is based on the evaluation of results obtained for a mixed standard containing 17 analytes, that is measured periodically with unknown samples. An inaccurate standard evaluation triggers restandardization of the instrument according to a predetermined protocol. Interaction of the computer-controlled manifold assembly hardware with the spectrometer system is outlined. Evaluation of the automated standardization system with respect to reliability, simplicity, flexibility, and efficiency is compared to the manual procedure. ?? 1982.

PEM-INST-001: Instructions for Plastic Encapsulated Microcircuit (PEM) Selection, Screening, and Qualification

NASA Technical Reports Server (NTRS)

Teverovsky, Alexander; Sahu, Kusum

2003-01-01

Potential users of plastic encapsulated microcircuits (PEMs) need to be reminded that unlike the military system of producing robust high-reliability microcircuits that are designed to perform acceptably in a variety of harsh environments, PEMs are primarily designed for use in benign environments where equipment is easily accessed for repair or replacement. The methods of analysis applied to military products to demonstrate high reliability cannot always be applied to PEMs. This makes it difficult for users to characterize PEMs for two reasons: 1. Due to the major differences in design and construction, the standard test practices used to ensure that military devices are robust and have high reliability often cannot be applied to PEMs that have a smaller operating temperature range and are typically more frail and susceptible to moisture absorption. In contrast, high-reliability military microcircuits usually utilize large, robust, high-temperature packages that are hermetically sealed. 2. Unlike the military high-reliability system, users of PEMs have little visibility into commercial manufacturers proprietary design, materials, die traceability, and production processes and procedures. There is no central authority that monitors PEM commercial product for quality, and there are no controls in place that can be imposed across all commercial manufacturers to provide confidence to high-reliability users that a common acceptable level of quality exists for all PEMs manufacturers. Consequently, there is no guaranteed control over the type of reliability that is built into commercial product, and there is no guarantee that different lots from the same manufacturer are equally acceptable. And regarding application, there is no guarantee that commercial products intended for use in benign environments will provide acceptable performance and reliability in harsh space environments. The qualification and screening processes contained in this document are intended to detect poor-quality lots and screen out early random failures from use in space flight hardware. However, since it cannot be guaranteed that quality was designed and built into PEMs that are appropriate for space applications, users cannot screen in quality that may not exist. It must be understood that due to the variety of materials, processes, and technologies used to design and produce PEMs, this test process may not accelerate and detect all failure mechanisms. While the tests herein will increase user confidence that PEMs with otherwise unknown reliability can be used in space environments, such testing may not guarantee the same level of reliability offered by military microcircuits. PEMs should only be used where due to performance needs there are no alternatives in the military high-reliability market, and projects are willing to accept higher risk.

An audit of a hospital-based Doppler ultrasound quality control protocol using a commercial string Doppler phantom.

PubMed

Cournane, S; Fagan, A J; Browne, J E

2014-05-01

Results from a four-year audit of a Doppler quality assurance (QA) program using a commercially available Doppler string phantom are presented. The suitability of the phantom was firstly determined and modifications were made to improve the reliability and quality of the measurements. QA of Doppler ultrasound equipment is very important as data obtained from these systems is used in patient management. It was found that if the braided-silk filament of the Doppler phantom was exchanged with an O-ring rubber filament and the velocity range below 50 cm/s was avoided for Doppler quality control (QC) measurements, then the maximum velocity accuracy (MVA) error and intrinsic spectral broadening (ISB) results obtained using this device had a repeatability of 18 ± 3.3% and 19 ± 3.5%, respectively. A consistent overestimation of the MVA of between 12% and 56% was found for each of the tested ultrasound systems. Of more concern was the variation of the overestimation within each respective transducer category: MVA errors of the linear, curvilinear and phased array probes were in the range 12.3-20.8%, 32.3-53.8% and 27-40.7%, respectively. There is a dearth of QA data for Doppler ultrasound; it would be beneficial if a multicentre longitudinal study was carried out using the same Doppler ultrasound test object to evaluate sensitivity to deterioration in performance measurements. Copyright © 2013 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Commercial Probiotic Products: A Call for Improved Quality Control. A Position Paper by the ESPGHAN Working Group for Probiotics and Prebiotics.

PubMed

Kolaček, Sanja; Hojsak, Iva; Berni Canani, Roberto; Guarino, Alfredo; Indrio, Flavia; Orel, Rok; Pot, Bruno; Shamir, Raanan; Szajewska, Hania; Vandenplas, Yvan; van Goudoever, Johannes; Weizman, Zvi

2017-07-01

Probiotics have been proposed for a number of indications ranging from the hypothetical long-term immunomodulatory effects to proven benefits in the management of different clinical conditions.An increasing number of commercial products containing probiotics are available. In those products, irrespective if it is food, food supplement, medical food, or drug, the probiotic microorganisms have to be present in a sufficient number by the end of the shelf-life, to pass through the gastrointestinal tract resisting acid and bile, to colonize the gut, and to retain functional properties required to obtain the suggested beneficial effect. Finally, it should be contamination-free.Studies organized worldwide and summarized in this article have shown that inconsistencies and deviations from the information provided on the product label are surprisingly common. Frequently strains are misidentified and misclassified, products are occasionally contaminated, sometimes with even facultative or obligatory pathogens, strains are not viable, the labeled number of colonies cannot be verified, or the functional properties are diminished to the extent that preclude the proposed health benefit. As the probiotic preparations are commonly used for a wide range of conditions, the aim of the Working Group was to summarize results of the studies looking into the quality of the probiotic products and to raise the awareness of the important issue of their quality control.Based on the results obtained, we strongly suggest a more stringent quality control process. This process should ensure that the probiotic content as mentioned on the label meets the actual content throughout the shelf life of the product, while no contamination is present.

Energy Auditor and Quality Control Inspector Competency Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Head, Heather R.; Kurnik, Charles W.; Schroeder, Derek

The Energy Auditor (EA) and Quality Control Inspector (QCI) Competency model was developed to identify the soft skills, foundational competencies and define the levels of Knowledge, Skills, and Abilities (KSAs) required to successfully perform the tasks defined in the EA and QCI Job Task Analysis (JTAs), the U.S. Department of Energy (DOE) used the U.S. Department of Labor's (DOL) Competency Model Clearinghouse resources to develop a QCI and EA Competency Model. To keep the QCI and EA competency model consistent with other construction and energy management competency models, DOE and the National Renewable Energy Laboratory used the existing 'Residential Constructionmore » Competency Model' and the 'Advanced Commercial Building Competency Model' where appropriate.« less

Water-quality characteristics of urban storm runoff at selected sites in East Baton Rouge Parish, Louisiana, February 2006 through November 2009

USGS Publications Warehouse

Frederick, C. Paul

2011-01-01

Water samples were collected at three watersheds in East Baton Rouge Parish, Louisiana, during February 2006 through November 2009 for continued evaluation of urban storm runoff. The watersheds represented land uses characterized predominantly as established commercial, industrial, and residential. The following water-quality data are reported: physical and chemical-related properties, fecal coliform, nutrients, trace elements, and organic compounds. Results of water-quality analyses enabled calculation of event-mean concentrations and estimated annual contaminant loads and yields of storm runoff from nonpoint sources for 12 water-quality properties and constituents. Lead met or exceeded the U.S. Environmental Protection Agency Maximum Contaminant Level of 15 micrograms per liter for drinking water standards in 4 of 14 samples. Low level concentrations of mercury were detected in all 14 samples, and half were two to four times above the reporting limit of 0.02 micrograms per liter. The average dissolved phosphorus concentrations from each land use were two to four times the U.S. Environmental Protection Agency criterion of 0.05 milligrams per liter. Diazinon was detected in one sample at a concentration of 0.2 micrograms per liter. In the residential watershed, the largest at 216 acres, contaminant loads for 5 of the 12 water-quality properties and constituents were highest, with 4 of these being nutrients. The industrial watershed, 97 acres, had the highest contaminant loads for 6 of the 12 water-quality properties and constituents with 3 of these being metals, which is indicative of the type of land use. Zinc had the highest metal load (155 pounds per year) in the industrial watershed, compared to 36 pounds per year in the residential watershed, and 32 pounds per year in the established commercial watershed. The industrial watershed had the highest yields for 8 of the 12 water-quality properties and constituents, whereas the established commercial watershed had the lowest yield for 5 of the 12. Lower yields from the established commercial and residential watersheds could be from Best Management Practices in place that help control increased runoff from impervious areas and land development. Metal yields from all the watersheds were less than 1 pound per acre per year, except for the zinc from the industrial watershed, which was 2 pounds per acre per year. Nutrient yields in the established commercial watershed were lowest for total nitrogen, ammonia plus organic nitrogen (Kjeldahl nitrogen), and dissolved phosphorus.

Radiation preservation and test marketing of fruits and vegetables

NASA Astrophysics Data System (ADS)

Zhicheng, Xu; Dong, Cai; Fuying, He; Deyao, Zhao

1993-07-01

To develop the technology for radiation preservation of fruits and vegetables, many varieties of fruits and vegetables had been researched. Results showed that the low dose irradiation is useful to preservation of fruits and vegetables. On the besis of research, 1900 tons garlic, 950 tons onion, 500 tons potatoes, 710 tons apples and 1000 kg litchi had been irradiated in commercial scale. The quality control standards of irradiated garlic, onion and potato had been established and used for commercial scale irradiation. In order to collect consumers in store response to irradiated foods, a special counter was set up for selling irradiated apples in Nan Jing Road (W), Shanghai. 634 sheets of consumer in-store respense investigation forms have been returned and analysed. These results showed that when consumer understands the benefit of irradiation preservation such as higher quality, greater safety, longer shelf-live, wide product availability, or good prices for value, consumer would willingly buy irradiated food.

A Practical Guide for Translators (Third Revised Edition). Topics in Translation 13.

ERIC Educational Resources Information Center

Samuelsson-Brown, Geoffrey

This third edition of a guide for translators contains more information than the second edition and looks at translation as a business as well as an occupation, focusing on marketing and quality control. It is designed for people with little or no practical experience with translation in a commercial environment. The 16 chapters examine these…

Meter Designs Reduce Operation Costs for Industry

NASA Technical Reports Server (NTRS)

2013-01-01

Marshall Space Flight Center collaborated with Quality Monitoring and Control (QMC) of Humble, Texas, through a Space Act Agreement to design a balanced flow meter for the Space Shuttle Program. QMC founded APlus-QMC LLC to commercialize the technology, which has contributed to 100 new jobs, approximately $250,000 in yearly sales, and saved customers an estimated $10 million.

Silviculture guide for the mahogany forests of Quintana Roo, Mexico – Criteria and recommendations

Treesearch

P. Negreros-Castillo; L. Cámara-Cabrales; Margaret Devall; M.A. Fajvan; M.A. Mendoza Briseño; C.W. Mize

2014-01-01

Silviculture is the art, science and practice of controlling the establishment, composition, health, quality and growth of forests to accomplish a set of management objectives. This publication offers an approach to silviculture of the forests of Quintana Roo in which mahogany (Swietenia macrophylla King), the commercially most important tree species in Latin America,...

A new method for long-term storage of titred microbial standard solutions suitable for microbiologic quality control activities of pharmaceutical companies.

PubMed

Chiellini, Carolina; Mocali, Stefano; Fani, Renato; Ferro, Iolanda; Bruschi, Serenella; Pinzani, Alessandro

2016-08-01

Commercially available lyophilized microbial standards are expensive and subject to reduction in cell viability due to freeze-drying stress. Here we introduce an inexpensive and straightforward method for in-house microbial standard preparation and cryoconservation that preserves constant cell titre and cell viability over 14 months.

Quality effects of sugar replacement with alternative sweetener blends in lean yellow-shortened cupcakes over a 4-day storage period

USDA-ARS?s Scientific Manuscript database

In lean yellow shortened cupcakes, the multiple ingredient approach was used to replace 100% of the sugar in the control with a commercial sucralose/maltodextrin blend (Splenda Granulated) and isomalt. Sugar substitutions were 100% Splenda Granulated (SP100), and two ratios of Splenda Granulated to ...

People’s Preferences of Urban Design Qualities for Walking on a Commercial Street

NASA Astrophysics Data System (ADS)

Ernawati, J.; Surjono; Sudarmo, B. S.

2018-03-01

This research aims to explore people’s preferences of urban design qualities for walking on a commercial street, with Kawi Street located in a commercial neighborhood in the town of Malang Indonesia as the case study. Based on a literature review, this study used eight urban design qualities, i.e., enclosure, legibility, human scale, transparency, complexity, coherence, linkage, and imageability. This study applied a survey research method using a self-administered paper-pencil questionnaire applying two measurement techniques: Likert scale was used to explore people’s evaluations of urban design qualities of the street, while multiple-rating scales were used to measure people’s preference for walking on the street. One hundred and ten people randomly selected as respondents. Regression analysis was employed to explore the influence of urban design qualities on people preference for walking. Results indicated four urban design qualities that affect people’s choice for walking on a commercial street, i.e., transparency, coherence, linkage, and imageability. Implications of the findings will be discussed in the paper.

Digital Control Technologies for Modular DC-DC Converters

NASA Technical Reports Server (NTRS)

Button, Robert M.; Kascak, Peter E.; Lebron-Velilla, Ramon

2002-01-01

Recent trends in aerospace Power Management and Distribution (PMAD) systems focus on using commercial off-the-shelf (COTS) components as standard building blocks. This move to more modular designs has been driven by a desire to reduce costs and development times, but is also due to the impressive power density and efficiency numbers achieved by today's commercial DC-DC converters. However, the PMAD designer quickly learns of the hidden "costs" of using COTS converters. The most significant cost is the required addition of external input filters to meet strict electromagnetic interference (MIAMI) requirements for space systems. In fact, the high power density numbers achieved by the commercial manufacturers are greatly due to the lack of necessary input filters included in the COTS module. The NASA Glenn Research Center is currently pursuing a digital control technology that addresses this problem with modular DC-DC converters. This paper presents the digital control technologies that have been developed to greatly reduce the input filter requirements for paralleled, modular DC-DC converters. Initial test result show that the input filter's inductor size was reduced by 75 percent, and the capacitor size was reduced by 94 percent while maintaining the same power quality specifications.

Gamma irradiation as a phytosanitary treatment for fresh pome fruits produced in Patagonia

NASA Astrophysics Data System (ADS)

Pérez, J.; Lires, C.; Horak, C.; Pawlak, E.; Docters, A.; Kairiyama, E.

2009-07-01

Argentina produces 1.8 million tons/year of apples ( Malus domestica L.) and pears ( Pyrus communis L.) in the Patagonia region. Cydia pomonella, codling moth, and Grapholita molesta, Oriental fruit moth, ( Lepidoptera: Tortricidae) are quarantine pests in pome fruits. Irradiation is a promising phytosanitary treatment because a dose of 200 Gy completely prevents pest adult emergence. A pilot irradiation process of commercially packaged 'Red Delicious' apples and 'Packham's Triumph' pears was performed in an irradiation facility with a Cobalt 60 source. Quality analyses were carried out at 0, 2, 4, 6 and 8 months of storage (1 °C, RH 99%) to evaluate fruit tolerance at 200, 400 and 800 Gy. Irradiation at 200 and 400 Gy had no undesirable effects on fruit quality (pulp firmness, external colour, soluble solids content (SSC), titratable acidity (TA) and sensory evaluations). Irradiation of 'Red Delicious' apples and 'Packham's Triumph' pears can be applied as a commercial quarantine treatment with a minimum absorbed dose of 200 Gy (to control codling moth and Oriental fruit moth) and <800 Gy (according to quality results).

Fuel cells provide a revenue-generating solution to power quality problems

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, J.M. Jr.

Electric power quality and reliability are becoming increasingly important as computers and microprocessors assume a larger role in commercial, health care and industrial buildings and processes. At the same time, constraints on transmission and distribution of power from central stations are making local areas vulnerable to low voltage, load addition limitations, power quality and power reliability problems. Many customers currently utilize some form of premium power in the form of standby generators and/or UPS systems. These include customers where continuous power is required because of health and safety or security reasons (hospitals, nursing homes, places of public assembly, air trafficmore » control, military installations, telecommunications, etc.) These also include customers with industrial or commercial processes which can`t tolerance an interruption of power because of product loss or equipment damage. The paper discusses the use of the PC25 fuel cell power plant for backup and parallel power supplies for critical industrial applications. Several PC25 installations are described: the use of propane in a PC25; the use by rural cooperatives; and a demonstration of PC25 technology using landfill gas.« less

Information systems as a quality management tool in clinical laboratories

NASA Astrophysics Data System (ADS)

Schmitz, Vanessa; Rosecler Bez el Boukhari, Marta

2007-11-01

This article describes information systems as a quality management tool in clinical laboratories. The quality of laboratory analyses is of fundamental importance for health professionals in aiding appropriate diagnosis and treatment. Information systems allow the automation of internal quality management processes, using standard sample tests, Levey-Jennings charts and Westgard multirule analysis. This simplifies evaluation and interpretation of quality tests and reduces the possibility of human error. This study proposes the development of an information system with appropriate functions and costs for the automation of internal quality control in small and medium-sized clinical laboratories. To this end, it evaluates the functions and usability of two commercial software products designed for this purpose, identifying the positive features of each, so that these can be taken into account during the development of the proposed system.

Quality Assurance of RNA Expression Profiling in Clinical Laboratories

PubMed Central

Tang, Weihua; Hu, Zhiyuan; Muallem, Hind; Gulley, Margaret L.

2012-01-01

RNA expression profiles are increasingly used to diagnose and classify disease, based on expression patterns of as many as several thousand RNAs. To ensure quality of expression profiling services in clinical settings, a standard operating procedure incorporates multiple quality indicators and controls, beginning with preanalytic specimen preparation and proceeding thorough analysis, interpretation, and reporting. Before testing, histopathological examination of each cellular specimen, along with optional cell enrichment procedures, ensures adequacy of the input tissue. Other tactics include endogenous controls to evaluate adequacy of RNA and exogenous or spiked controls to evaluate run- and patient-specific performance of the test system, respectively. Unique aspects of quality assurance for array-based tests include controls for the pertinent outcome signatures that often supersede controls for each individual analyte, built-in redundancy for critical analytes or biochemical pathways, and software-supported scrutiny of abundant data by a laboratory physician who interprets the findings in a manner facilitating appropriate medical intervention. Access to high-quality reagents, instruments, and software from commercial sources promotes standardization and adoption in clinical settings, once an assay is vetted in validation studies as being analytically sound and clinically useful. Careful attention to the well-honed principles of laboratory medicine, along with guidance from government and professional groups on strategies to preserve RNA and manage large data sets, promotes clinical-grade assay performance. PMID:22020152

MALDI-TOF MS for quality control of high protein content sport supplements.

PubMed

De Ceglie, Cristina; Calvano, Cosima D; Zambonin, Carlo G

2015-06-01

High protein content sport nutritional supplements are found as powder products containing, as ingredients, amino acids and proteins with important nutritional values as milk, soy and egg proteins. An EU Food Supplements Directive (2002) requires that supplements should be safe, both in dosages and in purity. It is important, then, to develop rapid and sensitive methods to be employed for the quality control of these substances. In this work, we apply, for the first time, matrix-assisted laser desorption ionization-mass spectrometry as a fast, reproducible and sensitive method for the quality control of sport nutritional supplements based on proteins. To this aim, several commercial egg- and/or milk-based powder products have been processed by in gel or in solution digestion and analyzed in comparison to pure standard products. This strategy allowed to assess the reliability of the indications on proteins (as caseins, whey proteins and ovalbumin) declared in the label of several sport nutritional supplements. Copyright © 2014 Elsevier Ltd. All rights reserved.

Feasibility of UV-VIS-Fluorescence spectroscopy combined with pattern recognition techniques to authenticate a new category of plant food supplements.

PubMed

Boggia, Raffaella; Turrini, Federica; Anselmo, Marco; Zunin, Paola; Donno, Dario; Beccaro, Gabriele L

2017-07-01

Bud extracts, named also "gemmoderivatives", are a new category of natural products, obtained macerating meristematic fresh tissues of trees and plants. In the European Community these botanical remedies are classified as plant food supplements. Nowadays these products are still poorly studied, even if they are widely used and commercialized. Several analytical tools for the quality control of these very expensive supplements are urgently needed in order to avoid mislabelling and frauds. In fact, besides the usual quality controls common to the other botanical dietary supplements, these extracts should be checked in order to quickly detect if the cheaper adult parts of the plants are deceptively used in place of the corresponding buds whose harvest-period and production are extremely limited. This study aims to provide a screening analytical method based on UV-VIS-Fluorescence spectroscopy coupled to multivariate analysis for a rapid, inexpensive and non-destructive quality control of these products.

Rapid and Accurate Evaluation of the Quality of Commercial Organic Fertilizers Using Near Infrared Spectroscopy

PubMed Central

Wang, Chang; Huang, Chichao; Qian, Jian; Xiao, Jian; Li, Huan; Wen, Yongli; He, Xinhua; Ran, Wei; Shen, Qirong; Yu, Guanghui

2014-01-01

The composting industry has been growing rapidly in China because of a boom in the animal industry. Therefore, a rapid and accurate assessment of the quality of commercial organic fertilizers is of the utmost importance. In this study, a novel technique that combines near infrared (NIR) spectroscopy with partial least squares (PLS) analysis is developed for rapidly and accurately assessing commercial organic fertilizers quality. A total of 104 commercial organic fertilizers were collected from full-scale compost factories in Jiangsu Province, east China. In general, the NIR-PLS technique showed accurate predictions of the total organic matter, water soluble organic nitrogen, pH, and germination index; less accurate results of the moisture, total nitrogen, and electrical conductivity; and the least accurate results for water soluble organic carbon. Our results suggested the combined NIR-PLS technique could be applied as a valuable tool to rapidly and accurately assess the quality of commercial organic fertilizers. PMID:24586313

Rapid and accurate evaluation of the quality of commercial organic fertilizers using near infrared spectroscopy.

PubMed

Wang, Chang; Huang, Chichao; Qian, Jian; Xiao, Jian; Li, Huan; Wen, Yongli; He, Xinhua; Ran, Wei; Shen, Qirong; Yu, Guanghui

2014-01-01

The composting industry has been growing rapidly in China because of a boom in the animal industry. Therefore, a rapid and accurate assessment of the quality of commercial organic fertilizers is of the utmost importance. In this study, a novel technique that combines near infrared (NIR) spectroscopy with partial least squares (PLS) analysis is developed for rapidly and accurately assessing commercial organic fertilizers quality. A total of 104 commercial organic fertilizers were collected from full-scale compost factories in Jiangsu Province, east China. In general, the NIR-PLS technique showed accurate predictions of the total organic matter, water soluble organic nitrogen, pH, and germination index; less accurate results of the moisture, total nitrogen, and electrical conductivity; and the least accurate results for water soluble organic carbon. Our results suggested the combined NIR-PLS technique could be applied as a valuable tool to rapidly and accurately assess the quality of commercial organic fertilizers.

Interplay of the Quality of Ciprofloxacin and Antibiotic Resistance in Developing Countries

PubMed Central

Sharma, Deepali; Patel, Rahul P.; Zaidi, Syed Tabish R.; Sarker, Md. Moklesur Rahman; Lean, Qi Ying; Ming, Long C.

2017-01-01

Ciprofloxacin, a second generation broad spectrum fluoroquinolone, is active against both Gram-positive and Gram-negative bacteria. Ciprofloxacin has a high oral bioavailability and a large volume of distribution. It is used for the treatment of a wide range of infections including urinary tract infections caused by susceptible bacteria. However, the availability and use of substandard and spurious quality of oral ciprofloxacin formulations in the developing countries has been thought to have contributed toward increased risk of treatment failure and bacterial resistance. Therefore, quality control and bioequivalence studies of the commercially available oral ciprofloxacin formulations should be monitored. Appropriate actions should be taken against offending manufacturers in order to prevent the sale of substandard and spurious quality of ciprofloxacin formulations. PMID:28871228

Controlled ice nucleation in the field of freeze-drying: fundamentals and technology review.

PubMed

Geidobler, R; Winter, G

2013-10-01

In the scientific community as well as in commercial freeze-drying, controlled ice nucleation has received a lot of attention because increasing the ice nucleation temperature can significantly reduce primary drying duration. Furthermore, controlled ice nucleation enables to reduce the randomness of the ice nucleation temperature, which can be a serious scale-up issue during process development. In this review, fundamentals of ice nucleation in the field of freeze-drying are presented. Furthermore, the impact of controlled ice nucleation on product qualities is discussed, and methods to achieve controlled ice nucleation are presented. Copyright © 2013 Elsevier B.V. All rights reserved.

Using Micromechanical Resonators to Measure Rheological Properties and Alcohol Content of Model Solutions and Commercial Beverages

PubMed Central

Paxman, Rosemary; Stinson, Jake; Dejardin, Anna; McKendry, Rachel A.; Hoogenboom, Bart W.

2012-01-01

Micromechanic resonators provide a small-volume and potentially high-throughput method to determine rheological properties of fluids. Here we explore the accuracy in measuring mass density and viscosity of ethanol-water and glycerol-water model solutions, using a simple and easily implemented model to deduce the hydrodynamic effects on resonating cantilevers of various length-to-width aspect ratios. We next show that these measurements can be extended to determine the alcohol percentage of both model solutions and commercial beverages such as beer, wine and liquor. This demonstrates how micromechanical resonators can be used for quality control of every-day drinks. PMID:22778654

Combination of Methoprene and Controlled Aeration to Manage Insects in Stored Wheat.

PubMed

Liu, Samuel S; Arthur, Frank H; VanGundy, Douglas; Phillips, Thomas W

2016-06-17

A commercial formulation of the insect growth regulator methoprene was applied to wheat stored in small bins either alone or in combination with controlled aeration of the bins, to lower grain temperature for insect pest management of stored wheat. Grain temperatures were monitored and modified by a computer-controlled thermocouple system that also activated the aeration system at programmed set-points to move cool ambient air through the grain mass to lower grain temperature. Results from sampling insect populations in experimental storage bins along with laboratory mortality bioassays of insects placed on wheat taken from the bins over the course of the storage period showed that methoprene was very effective in controlling infestation by the externally-feeding stored grain insects Plodia interpunctella (Hübner), the Indian meal moth Tribolium castaneum (Herbst), the red flour beetle, Cryptolestes ferrugineus (Stephens), the rusty grain beetle, and also for the internal-feeding pest Rhyzopertha dominica( Fauvel), the lesser grain borer. Methoprene did not give good control of the internal-feeding pest Sitophilus oryzae (L.), the rice weevil. Aeration alone was somewhat effective in suppressing insect population development, while methoprene alone or when combined with aeration greatly enhanced insect control. Commercial grain grading for industry quality standards at the end of the storage period confirmed the impact of insect suppression on maintaining high quality of the stored wheat. This field experiment shows that methoprene combined with aeration to cool grain can be effective for pest management of stored wheat in the southern plains of the United States of America.

Different carbonization process of bamboo charcoal using Gigantochloa Albociliata

NASA Astrophysics Data System (ADS)

Isa, S. S. M.; Ramli, M. M.; Halin, D. S. C.; Anhar, N. A. M.; Hambali, N. A. M. A.

2017-09-01

Bamboo charcoal has attracted a lot of interests due to their microporous structure, high surface area and great adsorption properties. Some of the applications utilizing this material focused on these advantages such as water purification, electromagnetic wave absorber and blood purification. However, these advantages really depend on the carbonization and activation process of bamboo charcoal. The production must be carried out in properly control environment with precise temperatures and timing. This paper report the production of bamboo charcoal using Gigantochloa Albociliata in controlled environment at 500 °C for 1 hour (lab-prepared). Then the material was characterized for their dispersibility and adsorption behaviour. Furthermore, the bamboo charcoal that was produced commercially, by company, was also characterized and compared. The results show, bamboo charcoal produced by lab-prepared has similar qualities with the commercial bamboo charcoal.

Development of an advanced pitch active control system for a wide body jet aircraft

NASA Technical Reports Server (NTRS)

Guinn, Wiley A.; Rising, Jerry J.; Davis, Walt J.

1984-01-01

An advanced PACS control law was developed for a commercial wide-body transport (Lockheed L-1011) by using modern control theory. Validity of the control law was demonstrated by piloted flight simulation tests on the NASA Langley visual motion simulator. The PACS design objective was to develop a PACS that would provide good flying qualities to negative 10 percent static stability margins that were equivalent to those of the baseline aircraft at a 15 percent static stability margin which is normal for the L-1011. Also, the PACS was to compensate for high-Mach/high-g instabilities that degrade flying qualities during upset recoveries and maneuvers. The piloted flight simulation tests showed that the PACS met the design objectives. The simulation demonstrated good flying qualities to negative 20 percent static stability margins for hold, cruise and high-speed flight conditions. Analysis and wind tunnel tests performed on other Lockheed programs indicate that the PACS could be used on an advanced transport configuration to provide a 4 percent fuel savings which results from reduced trim drag by flying at negative static stability margins.

Inter-laboratory validation of an inexpensive streamlined method to measure inorganic arsenic in rice grain

USDA-ARS?s Scientific Manuscript database

With the establishment by CODEX of a 200 ng/g limit of inorganic arsenic (iAs) in polished rice grain, more analyses of iAs will be necessary to ensure compliance in regulatory and trade applications, to assess quality control in commercial rice production, and to conduct research involving iAs in r...

Selection of chemical markers for the quality control of medicinal plants of the genus Cecropia.

PubMed

Rivera-Mondragón, Andrés; Ortíz, Orlando O; Bijttebier, Sebastiaan; Vlietinck, Arnold; Apers, Sandra; Pieters, Luc; Caballero-George, Catherina

2017-12-01

Several Cecropia (Cecropiaceae) species are traditionally used in Latin America for the treatment of a variety of diseases including diabetes, arterial hypertension, asthma, bronchitis, anxiety, and inflammation. At present, a number of commercial products based on these plants have been introduced into the market with very little information on methods for guaranteeing their quality and safety. This work proposes potential chemical markers for the quality control of the raw materials of Cecropia obtusifolia Bertol., Cecropia peltata L., Cecropia glaziovii Snethl., Cecropia pachystachya Trécul, and Cecropia hololeuca Miq. The Herbal Chemical Marker Ranking System (Herb MaRS) developed by the National Institute of Complementary Medicine (NICM) at the University of Western Sydney was used for selecting chemical markers for the quality control of selected medicinal species of Cecropia. This review covers the period from 1982 to 2016. Chlorogenic acid, flavonoidal glycosides (orientin, isoorientin, vitexin, isovitexin, and rutin), catechin, epicatechin, procyanidins (B2, B5, and C1), steroids (β-sitosterol), and triterpenoids (α-amyrin, pomolic, tormentic and ursolic acids) were selected as chemical markers for the quality control of the leaves. It is necessary to establish comprehensive standards for guaranteeing quality, safety and efficacy of herbal drugs. The selection of adequate chemical markers for quality control purposes requires a good knowledge about the chemical composition of medicinal plants and their associated biological properties. To the best of our knowledge this review article is the first to address the identification and quantitative determination of the chemical markers for the genus Cecropia.

Reducing Bits in Electrodeposition Process of Commercial Vehicle - A Case Study

NASA Astrophysics Data System (ADS)

Rahim, Nabiilah Ab; Hamedon, Zamzuri; Mohd Turan, Faiz; Iskandar, Ismed

2016-02-01

Painting process is critical in commercial vehicle manufacturing process for protection and decorative. The good quality on painted body is important to reduce repair cost and achieve customer satisfaction. In order to achieve the good quality, it is important to reduce the defect at the first process in painting process which is electrodeposition process. The Pareto graph and cause and effect diagram in the seven QC tools is utilized to reduce the electrodeposition defects. The main defects in the electrodeposition process in this case study are the bits. The 55% of the bits are iron filings. The iron filings which come from the metal assembly process at the body shop are minimised by controlling the spot welding parameter, defect control and standard body cleaning process. However the iron filings are still remained on the body and carry over to the paint shop. The remained iron filings on the body are settled inside the dipping tank and removed by filtration system and magnetic separation. The implementation of filtration system and magnetic separation improved 27% of bits and reduced 42% of sanding man hour with a total saving of RM38.00 per unit.

3D Printing, Additive Manufacturing, and Solid Freeform Fabrication: The Technologies of the Past, Present and Future

NASA Astrophysics Data System (ADS)

Beaman, Joseph

2015-03-01

Starting in the late 1980's, several new technologies were created that have the potential to revolutionize manufacturing. These technologies are, for the most part, additive processes that build up parts layer by layer. In addition, the processes that are being touted for hard-core manufacturing are primarily laser or e-beam based processes. This presentation gives a brief history of Additive Manufacturing and gives an assessment for these technologies. These technologies initially grew out of a commercial need for rapid prototyping. This market has a different requirement for process and quality control than traditional manufacturing. The relatively poor process control of the existing commercial Additive Manufacturing equipment is a vestige of this history. This presentation discusses this history and improvements in quality over time. The emphasis will be on Additive Manufacturing processes that are being considered for direct manufacturing, which is a different market than the 3D Printing ``Makerbot'' market. Topics discussed include past and present machine sensors, materials, and operational methods that were used in the past and those that are used today to create manufactured parts. Finally, a discussion of new methods and future directions of AM is presented.

Evaluation of different commercial feeds on grow-out silver black porgy, Sparidentex hasta (Valenciennes), for optimum growth performance, fillet quality, and cost of production.

PubMed

Hossain, M A; Al-Abdul-Elah, K M; El-Dakour, S

2017-01-01

The objective of the study was to find a cost-effective feed from three commercial feeds, namely, Arasco (Saudi Arabia), Skretting (Turkey), and Biomar (Greece) for commercially producing silver black porgy (sobaity bream), Sparidentex hasta in Kuwait. For confidentiality, these feeds were randomly given code names, diets 1, 2, and 3, which were known only to the investigating staffs. The trash fish (diet 4) was used as the control. The experiment was conducted for 28 wk with grow-out sobaity bream (210.0 ± 0.51 g) using a flow-through system consisting of twelve 1-m 3 tanks. There were three replicates for each treatment. Fish were fed two times daily at satiation level. The results showed that fish fed diet 2 resulted in significantly ( P  > 0.05) better growth performance, feed utilization, and higher fillet eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) content compared to other diets. A comparison of fillet quality of cultured and wild sobaity bream showed no significant ( P  > 0.05) difference between sensory attributes, except that of 'flavor' in cooked fillets of wild sobaity bream. A simple economic analysis showed that the cost per kilogram of fish production was significantly ( P  > 0.05) the lowest in diet 2 (USD4.13), followed by diet 1 (USD5.70), diet 4 (USD6.33), and diet 3 (USD6.92). Thus, based on growth performance, feed utilization, cost of production, and nutritional quality of fillet, it is concluded that diet 2 may be recommended for commercial culture of sobaity bream in Kuwait. However, future research should focus on how to improve fillet quality of the cultured fish at par with wild fish by manipulating the feed formulation.

Influence of Customer Quality Perception on the Effectiveness of Commercial Stimuli for Electronic Products.

PubMed

Garrido-Morgado, Álvaro; González-Benito, Óscar; Martos-Partal, Mercedes

2016-01-01

Creating and maintaining customer loyalty are strategic requirements for modern business. In the current competitive context, product quality, and brand experience are crucial in building and maintaining customer loyalty. Consumer loyalty, which may be classified into cognitive loyalty and affective loyalty, is related to customers' quality perception. Cue utilization theory distinguishes two dimensions for perceived quality, extrinsic quality-linked to the brand-and intrinsic quality-related with internal product characteristics. We propose that (i) cognitive loyalty is more influenced by intrinsic product quality whereas extrinsic product quality (brand name) is more salient for affective loyalty and, (ii) different commercial stimuli have a differential effectiveness on intrinsic and extrinsic perceived quality. In fact, in this study, we analyze how perceived quality dimensions may influence the effectiveness of two different commercial stimuli: displays and advertising flyers. While displays work within the point of sale under time-constrained conditions where consumers are more likely to use heuristics to simplify their decisions, advertising flyers work outside of the point of sale under low time-constrained conditions, and therefore favor a more reasoned purchase decision where systematic processing will be more likely. We analyze the role of quality perception in determining the effectiveness of both these commercial stimuli for selling products that induce high purchase involvement and perceived risk. The empirical analysis focuses on computer products sold by one of Europe's largest computer retailers and it combines scanner, observational, and survey data. The results show that both dimensions of quality perceptions moderate the influence of displays and advertising flyers on sales, but their impact is different on each commercial stimuli. Extrinsic quality perception increases to a greater extent the effect of displays due to the use of a brand name heuristic. However, intrinsic quality perception improves to a greater extent the effect of advertising flyers, which in turn are more closely related to systematic decision processing.

Quality management for the international transport of laboratory animals.

PubMed

Leary, Steven L

2008-01-01

Increased collaboration between investigators at different institutions has increased the number of laboratory animals being transported. The current system of laws and regulations governing animal shipments is inconsistent and government agencies often have areas of overlapping regulatory management. Furthermore, the lack of industry-wide shipping standards and good practices contributes to confusion among those responsible for shipment. One answer to these quality control issues would be the establishment of independent, industry-regulated 'good practices' for animal transport, similar to those used in laboratories for experimental design. These good practices could be based on the existing International Air Transport Association Live Animals Regulations, with contributions from representatives of the specialties involved. Additionally, quality control under the current system of patchwork regulations could be improved if each institution, both academic and commercial, would designate a single point of contact to follow each shipment from start to finish.

The April 1994 and October 1994 radon intercomparisons at EML

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisenne, I.M.; George, A.C.; Perry, P.M.

1995-10-01

Quality assurance/quality control (QA/QC) are the backbone of many commercial and research processes and programs. QA/QC research tests the state of a functioning system, be it the production of manufactured goods or the ability to make accurate and precise measurements. The quality of the radon measurements in the US have been tested under controlled conditions in semi-annual radon gas intercomparison exercises sponsored by the Environmental Measurements Laboratory (EML) since 1981. The two Calendar Year 1994 radon gas intercomparison exercises were conducted in the EML exposure chamber. Thirty-two groups including US Federal facilities, USDOE contractors, national and state laboratories, universities andmore » foreign institutions participated in these exercises. The majority of the participant`s results were within {+-}10% of the EML value at radon concentrations of 570 and 945 Bq m{sup {minus}3}.« less

Openstage: A Low-Cost Motorized Microscope Stage with Sub-Micron Positioning Accuracy

PubMed Central

Campbell, Robert A. A.; Eifert, Robert W.; Turner, Glenn C.

2014-01-01

Recent progress in intracellular calcium sensors and other fluorophores has promoted the widespread adoption of functional optical imaging in the life sciences. Home-built multiphoton microscopes are easy to build, highly customizable, and cost effective. For many imaging applications a 3-axis motorized stage is critical, but commercially available motorization hardware (motorized translators, controller boxes, etc) are often very expensive. Furthermore, the firmware on commercial motor controllers cannot easily be altered and is not usually designed with a microscope stage in mind. Here we describe an open-source motorization solution that is simple to construct, yet far cheaper and more customizable than commercial offerings. The cost of the controller and motorization hardware are under $1000. Hardware costs are kept low by replacing linear actuators with high quality stepper motors. Electronics are assembled from commonly available hobby components, which are easy to work with. Here we describe assembly of the system and quantify the positioning accuracy of all three axes. We obtain positioning repeatability of the order of in X/Y and in Z. A hand-held control-pad allows the user to direct stage motion precisely over a wide range of speeds ( to ), rapidly store and return to different locations, and execute “jumps” of a fixed size. In addition, the system can be controlled from a PC serial port. Our “OpenStage” controller is sufficiently flexible that it could be used to drive other devices, such as micro-manipulators, with minimal modifications. PMID:24586468

Flexible control techniques for a lunar base

NASA Technical Reports Server (NTRS)

Kraus, Thomas W.

1992-01-01

The fundamental elements found in every terrestrial control system can be employed in all lunar applications. These elements include sensors which measure physical properties, controllers which acquire sensor data and calculate a control response, and actuators which apply the control output to the process. The unique characteristics of the lunar environment will certainly require the development of new control system technology. However, weightlessness, harsh atmospheric conditions, temperature extremes, and radiation hazards will most significantly impact the design of sensors and actuators. The controller and associated control algorithms, which are the most complex element of any control system, can be derived in their entirety from existing technology. Lunar process control applications -- ranging from small-scale research projects to full-scale processing plants -- will benefit greatly from the controller advances being developed today. In particular, new software technology aimed at commercial process monitoring and control applications will almost completely eliminate the need for custom programs and the lengthy development and testing cycle they require. The applicability of existing industrial software to lunar applications has other significant advantages in addition to cost and quality. This software is designed to run on standard hardware platforms and takes advantage of existing LAN and telecommunications technology. Further, in order to exploit the existing commercial market, the software is being designed to be implemented by users of all skill levels -- typically users who are familiar with their process, but not necessarily with software or control theory. This means that specialized technical support personnel will not need to be on-hand, and the associated costs are eliminated. Finally, the latest industrial software designed for the commercial market is extremely flexible, in order to fit the requirements of many types of processing applications with little or no customization. This means that lunar process control projects will not be delayed by unforeseen problems or last minute process modifications. The software will include all of the tools needed to adapt to virtually any changes. In contrast to other space programs which required the development of tremendous amounts of custom software, lunar-based processing facilities will benefit from the use of existing software technology which is being proven in commercial applications on Earth.

Biology and genetic engineering of fruit maturation for enhanced quality and shelf-life.

PubMed

Matas, Antonio J; Gapper, Nigel E; Chung, Mi-Young; Giovannoni, James J; Rose, Jocelyn K C

2009-04-01

Commercial regulation of ripening is currently achieved through early harvest, by controlling the postharvest storage atmosphere and genetic selection for slow or late ripening varieties. Although these approaches are often effective, they are not universally applicable and often result in acceptable, but poor quality, products. With increased understanding of the molecular biology underlying ripening and the advent of genetic engineering technologies, researchers have pursued new strategies to address problems in fruit shelf-life and quality. These have been guided by recent insights into mechanisms by which ethylene and a complex network of transcription factors regulate ripening, and by an increased appreciation of factors that contribute to shelf-life, such as the fruit cuticle.

Evaluation of the ability of commercial wine yeasts to form biofilms (mats) and adhere to plastic: implications for the microbiota of the winery environment.

PubMed

Tek, Ee Lin; Sundstrom, Joanna F; Gardner, Jennifer M; Oliver, Stephen G; Jiranek, Vladimir

2018-02-01

Commercially available active dried wine yeasts are regularly used by winemakers worldwide to achieve reliable fermentations and obtain quality wine. This practice has led to increased evidence of traces of commercial wine yeast in the vineyard, winery and uninoculated musts. The mechanism(s) that enables commercial wine yeast to persist in the winery environment and the influence to native microbial communities on this persistence is poorly understood. This study has investigated the ability of commercial wine yeasts to form biofilms and adhere to plastic. The results indicate that the biofilms formed by commercial yeasts consist of cells with a combination of different lifestyles (replicative and non-replicative) and growth modes including invasive growth, bud elongation, sporulation and a mat sectoring-like phenotype. Invasive growth was greatly enhanced on grape pulp regardless of strain, while adhesion on plastic varied between strains. The findings suggest a possible mechanism that allows commercial yeast to colonise and survive in the winery environment, which may have implications for the indigenous microbiota profile as well as the population profile in uninoculated fermentations if their dissemination is not controlled. © FEMS 2018. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Quality control of commercial bovine lactoferrin.

PubMed

Wakabayashi, Hiroyuki; Yamauchi, Koji; Abe, Fumiaki

2018-06-01

Herein we review commercial bovine lactoferrin quality issues by describing an example of industrial production, the current status of global quality standardization, and quality-activity concerns for further discussion. Morinaga Milk Industry has been industrially producing bovine lactoferrin in Milei GmbH, Germany, since 1989. We delineate its production and quality as an example of safe and high-quality manufacturing. Currently, global standardization in the quality of bovine lactoferrin is progressing through Novel Food and GRAS in the EU and USA, respectively. Novel Food was applied or notified to seven lactoferrin manufacturers and GRAS was notified to three manufacturers, two of which are for infant use and one is for adult use, by the end of 2017. The specifications of these regulations are relatively high, including more than 95% lactoferrin purity in protein, which means that such companies can supply relatively high-grade lactoferrin. There appear to be several concerns regarding lactoferrin quality affecting activities, including contamination of lipopolysaccharide (LPS) and angiogenin, purity, and degradation of lactoferrin sample. Although LPS is immunologically toxic when invading the body, it is distributed normally in foods and the gut. However, an industrial lactoferrin sample may contain LPS at a maximum LPS/lactoferrin molecule ratio = 1/1724, which means 99.9% of the lactoferrin molecule is LPS-free. It is difficult to speculate that LPS contained in a lactoferrin sample affects its activities. Finally in order to achieve good and reproducible results, we make proposals to researchers a use of high-grade lactoferrin, careful storage, and indication the manufacturers' names and specifications in the paper.

Land cover controls on summer discharge and runoff solution chemistry of semi-arid urban catchments

NASA Astrophysics Data System (ADS)

Gallo, Erika L.; Brooks, Paul D.; Lohse, Kathleen A.; McLain, Jean E. T.

2013-04-01

SummaryRecharge of urban runoff to groundwater as a stormwater management practice has gained importance in semi-arid regions where water resources are scarce and urban centers are growing. Despite this trend, the importance of land cover in controlling semi-arid catchment runoff quantity and quality remains unclear. Here we address the question: How do land cover characteristics control the amount and quality of storm runoff in semi-arid urban catchments? We monitored summertime runoff quantity and quality from five catchments dominated by distinct urban land uses: low, medium, and high density residential, mixed use, and commercial. Increasing urban land cover increased runoff duration and the likelihood that a rainfall event would result in runoff, but did not increase the time to peak discharge of episodic runoff. The effect of urban land cover on hydrologic responses was tightly coupled to the magnitude of rainfall. At distinct rainfall thresholds, roads, percent impervious cover and the stormwater drainage network controlled runoff frequency, runoff depth and runoff ratios. Contrary to initial expectations, runoff quality did not vary in repose to impervious cover or land use. We identified four major mechanisms controlling runoff quality: (1) variable solute sourcing due to land use heterogeneity and above ground catchment connectivity; (2) the spatial extent of pervious and biogeochemically active areas; (3) the efficiency of overland flow and runoff mobilization; and (4) solute flushing and dilution. Our study highlights the importance of the stormwater drainage systems characteristics in controlling urban runoff quantity and quality; and suggests that enhanced wetting and in-stream processes may control solute sourcing and retention. Finally, we suggest that the characteristics of the stormwater drainage system should be integrated into stormwater management approaches.

Properties of high quality GaP single crystals grown by computer controlled liquid encapsulated Czochralski technique

NASA Astrophysics Data System (ADS)

Kokubun, Y.; Washizuka, S.; Ushizawa, J.; Watanabe, M.; Fukuda, T.

1982-11-01

The properties of GaP single crystals grown by an automatically diameter controlled liquid encapsulated Czochralski technique using a computer have been studied. A dislocation density less than 5×104 cm-2 has been observed for crystal grown in a temperature gradient lower than 70 °C/cm near the solid-liquid interface. Crystals have about 10% higher electron mobility than that of commercially available coracle controlled crystals and have 0.2˜0.5 compensation ratios. Yellow light emitting diodes using computer controlled (100) substrates have shown extremely high external quantum efficiency of 0.3%.

Performance of a web-based, realtime, tele-ultrasound consultation system over high-speed commercial telecommunication lines.

PubMed

Yoo, Sun K; Kim, D K; Jung, S M; Kim, E-K; Lim, J S; Kim, J H

2004-01-01

A Web-based, realtime, tele-ultrasound consultation system was designed. The system employed ActiveX control, MPEG-4 coding of full-resolution ultrasound video (640 x 480 pixels at 30 frames/s) and H.320 videoconferencing. It could be used via a Web browser. The system was evaluated over three types of commercial line: a cable connection, ADSL and VDSL. Three radiologists assessed the quality of compressed and uncompressed ultrasound video-sequences from 16 cases (10 abnormal livers, four abnormal kidneys and two abnormal gallbladders). The radiologists' scores showed that, at a given frame rate, increasing the bit rate was associated with increasing quality; however, at a certain threshold bit rate the quality did not increase significantly. The peak signal to noise ratio (PSNR) was also measured between the compressed and uncompressed images. In most cases, the PSNR increased as the bit rate increased, and increased as the number of dropped frames increased. There was a threshold bit rate, at a given frame rate, at which the PSNR did not improve significantly. Taking into account both sets of threshold values, a bit rate of more than 0.6 Mbit/s, at 30 frames/s, is suggested as the threshold for the maintenance of diagnostic image quality.

Nutritional quality of lunches consumed by Korean workers: Comparison between institutional and commercial lunches

PubMed Central

Kim, Won Gyoung; Choi, Injoo

2016-01-01

BACKGROUND/OBJECTIVES The nutritional quality of lunches is an important factor related to workers' health. This study examined the nutritional quality of Korean workers' lunches with a focus on comparing institutional and commercial lunches. SUBJECTS/METHODS The data from a 1-day, 24-hour dietary recall from the 5th Korea National Health and Nutrition Examination Survey (2010-2012) were analyzed. A total of 2,192 subjects aged 19 to 64 years, who had consumed lunches served by institutional or commercial food service vendors, were included for analysis. The nutritional quality of the lunches of the institutional lunch group (n=626) and the commercial lunch group (n=1,566) was compared in terms of the number of servings, food groups, nutrient intake, Nutrient Adequacy Ratio (NAR), and Mean Adequacy Ratio (MAR). RESULTS The NAR and MAR were significantly higher in the institutional lunches than in the commercial lunches, but more than half of workers in both groups obtained over 65% of their energy from carbohydrate. The average sodium intake from the lunches exceeded the daily intake goal (2,000 mg) in both groups. More than half of workers in both groups presented less than one-third of their respective recommended daily intake of riboflavin and calcium. With the exception of riboflavin, the nutrient intake from lunches accounted for more than 35% of the daily nutrient intake. CONCLUSIONS The overall nutritional quality of institutional lunches was higher than that of commercial lunches. However, institutional lunches had room for improvement in terms of nutritional quality. PMID:27909558

Assessment of the quality and content of website health information about herbal remedies for menopausal symptoms.

PubMed

Sowter, Julie; Astin, Felicity; Dye, Louise; Marshall, Paul; Knapp, Peter

2016-06-01

To assess the quality, readability and coverage of website information about herbal remedies for menopausal symptoms. A purposive sample of commercial and non-commercial websites was assessed for quality (DISCERN), readability (SMOG) and information coverage. Non-parametric and parametric tests were used to explain the variability of these factors across types of websites and to assess associations between website quality and information coverage. 39 sites were assessed. Median quality and information coverage scores were 44/80 and 11/30 respectively. The median readability score was 18.7, similar to UK broadsheets. Commercial websites scored significantly lower on quality (p=0.014), but there were no statistical differences for information coverage or readability. There was a significant positive correlation between information quality and coverage scores irrespective of website provider (r=0.69, p<0.001, n=39). Overall website quality and information coverage are poor and the required reading level high. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Influence of Customer Quality Perception on the Effectiveness of Commercial Stimuli for Electronic Products

PubMed Central

Garrido-Morgado, Álvaro; González-Benito, Óscar; Martos-Partal, Mercedes

2016-01-01

Creating and maintaining customer loyalty are strategic requirements for modern business. In the current competitive context, product quality, and brand experience are crucial in building and maintaining customer loyalty. Consumer loyalty, which may be classified into cognitive loyalty and affective loyalty, is related to customers' quality perception. Cue utilization theory distinguishes two dimensions for perceived quality, extrinsic quality—linked to the brand—and intrinsic quality—related with internal product characteristics. We propose that (i) cognitive loyalty is more influenced by intrinsic product quality whereas extrinsic product quality (brand name) is more salient for affective loyalty and, (ii) different commercial stimuli have a differential effectiveness on intrinsic and extrinsic perceived quality. In fact, in this study, we analyze how perceived quality dimensions may influence the effectiveness of two different commercial stimuli: displays and advertising flyers. While displays work within the point of sale under time-constrained conditions where consumers are more likely to use heuristics to simplify their decisions, advertising flyers work outside of the point of sale under low time-constrained conditions, and therefore favor a more reasoned purchase decision where systematic processing will be more likely. We analyze the role of quality perception in determining the effectiveness of both these commercial stimuli for selling products that induce high purchase involvement and perceived risk. The empirical analysis focuses on computer products sold by one of Europe's largest computer retailers and it combines scanner, observational, and survey data. The results show that both dimensions of quality perceptions moderate the influence of displays and advertising flyers on sales, but their impact is different on each commercial stimuli. Extrinsic quality perception increases to a greater extent the effect of displays due to the use of a brand name heuristic. However, intrinsic quality perception improves to a greater extent the effect of advertising flyers, which in turn are more closely related to systematic decision processing. PMID:27014144

How Online Quality Ratings Influence Patients’ Choice of Medical Providers: Controlled Experimental Survey Study

PubMed Central

Wang, Weiguang; Gao, Guodong (Gordon); Agarwal, Ritu

2018-01-01

Background In recent years, the information environment for patients to learn about physician quality is being rapidly changed by Web-based ratings from both commercial and government efforts. However, little is known about how various types of Web-based ratings affect individuals’ choice of physicians. Objective The objective of this research was to measure the relative importance of Web-based quality ratings from governmental and commercial agencies on individuals’ choice of primary care physicians. Methods In a choice-based conjoint experiment conducted on a sample of 1000 Amazon Mechanical Turk users in October 2016, individuals were asked to choose their preferred primary care physician from pairs of physicians with different ratings in clinical and nonclinical aspects of care provided by governmental and commercial agencies. Results The relative log odds of choosing a physician increases by 1.31 (95% CI 1.26-1.37; P<.001) and 1.32 (95% CI 1.27-1.39; P<.001) units when the government clinical ratings and commercial nonclinical ratings move from 2 to 4 stars, respectively. The relative log odds of choosing a physician increases by 1.12 (95% CI 1.07-1.18; P<.001) units when the commercial clinical ratings move from 2 to 4 stars. The relative log odds of selecting a physician with 4 stars in nonclinical ratings provided by the government is 1.03 (95% CI 0.98-1.09; P<.001) units higher than a physician with 2 stars in this rating. The log odds of selecting a physician with 4 stars in nonclinical government ratings relative to a physician with 2 stars is 0.23 (95% CI 0.13-0.33; P<.001) units higher for females compared with males. Similar star increase in nonclinical commercial ratings increases the relative log odds of selecting the physician by female respondents by 0.15 (95% CI 0.04-0.26; P=.006) units. Conclusions Individuals perceive nonclinical ratings provided by commercial websites as important as clinical ratings provided by government websites when choosing a primary care physician. There are significant gender differences in how the ratings are used. More research is needed on whether patients are making the best use of different types of ratings, as well as the optimal allocation of resources in improving physician ratings from the government’s perspective. PMID:29581091

Field performance and genetic makeup of RU1001161, a good quality selection from crosses between weed-suppressive indica rice and commercial U.S. southern long grains

USDA-ARS?s Scientific Manuscript database

Sustainable, economically viable weed control is an ongoing challenge in U.S. rice production, particularly in light of increased resistance to herbicides in populations of Echinochloa crus-galli (barnyardgrass) and other weed species. Indica rice lines such as PI 312777 and PI 338046 have been sho...

A Review of Dynamic Characteristics of Magnetically Levitated Vehicle Systems.

DTIC Science & Technology

1995-11-01

The dynamic response of magnetically levitated ( maglev ) ground transportation systems has important consequences for safety and ride quality...smoothness and levitation and control systems must be considered if maglev systems are to be economically feasible. The link between the guideway and the...other maglev components is vehicle dynamics. For a commercial maglev system, vehicle dynamics must be analyzed and tested in detail. This report, which

Advanced instrumentation for QELS experiments

NASA Technical Reports Server (NTRS)

Tscharnuter, Walther; Weiner, Bruce; Thomas, John

1989-01-01

Quasi Elastic Light Scattering (QELS) experiments have become an important tool in both research and quality control applications during the past 25 years. From the crude beginnings employing mechanically driven spectrum analyzers, an impressive array of general purpose digital correlators and special purpose particle sizers is now commercially available. The principles of QELS experiments are reviewed, their advantages and disadvantages are discussed and new instrumentation is described.

Content Integrity, Conflict of Interest, and Commercial Support: Defining and Operationalizing the Terms.

PubMed

Dickerson, Pam; Chappell, Kathy

2015-01-01

One of the hallmarks of quality continuing education developed using accreditation criteria is content integrity. Components of content integrity include identifying, resolving, and disclosing conflict of interest; ensuring content is based on the best available evidence; managing commercial support (if applicable); and presenting the educational activity free of promotion or bias. This article explores content integrity, conflict of interest, and commercial support. Understanding and being able to operationalize these concepts will enable providers to offer high-quality educational activities that promote the professional development of nurses and/or improve the quality of patient care.

An engineering approach to controlling indoor air quality.

PubMed

Woods, J E

1991-11-01

Evidence is accumulating that indicates air quality problems in residential and commercial buildings are nearly always associated with inadequacies in building design and methods of operation. Thus, the very systems depended on to control the indoor environment can become indirect sources of contamination if diligence is not exercised at each stage of a building's life: a) planning and design, b) construction and commissioning, c) operation, and d) demolition or renovation. In this paper, an engineering perspective is presented in which the existing building stock is characterized in terms of its environmental performance. Preliminary data indicate that 20 to 30% of the existing buildings have sufficient problems to manifest as sick-building syndrome or building-related illness, while another 10 to 20% may have undetected problems. Thus, only about 50 to 70% of the existing buildings qualify as healthy buildings. Two methods and three mechanisms of control are described to achieve "acceptable" indoor air quality: source control and exposure control. If sources cannot be removed, some level of occupant exposure will result. To control exposures with acceptable values, the primary sensory receptors of the occupants (i.e., thermal, ocular, auditory, and olfactory) cannot be excessively stimulated. The three exposure control mechanisms are conduction, radiation, and convection. To achieve acceptable occupant responses, it is often practical to integrate the mechanisms of radiation and convection in heating, ventilating, and air conditioning systems that are designed to provide acceptable thermal, acoustic, and air quality conditions within occupied spaces.(ABSTRACT TRUNCATED AT 250 WORDS)

An engineering approach to controlling indoor air quality.

PubMed Central

Woods, J E

1991-01-01

Evidence is accumulating that indicates air quality problems in residential and commercial buildings are nearly always associated with inadequacies in building design and methods of operation. Thus, the very systems depended on to control the indoor environment can become indirect sources of contamination if diligence is not exercised at each stage of a building's life: a) planning and design, b) construction and commissioning, c) operation, and d) demolition or renovation. In this paper, an engineering perspective is presented in which the existing building stock is characterized in terms of its environmental performance. Preliminary data indicate that 20 to 30% of the existing buildings have sufficient problems to manifest as sick-building syndrome or building-related illness, while another 10 to 20% may have undetected problems. Thus, only about 50 to 70% of the existing buildings qualify as healthy buildings. Two methods and three mechanisms of control are described to achieve "acceptable" indoor air quality: source control and exposure control. If sources cannot be removed, some level of occupant exposure will result. To control exposures with acceptable values, the primary sensory receptors of the occupants (i.e., thermal, ocular, auditory, and olfactory) cannot be excessively stimulated. The three exposure control mechanisms are conduction, radiation, and convection. To achieve acceptable occupant responses, it is often practical to integrate the mechanisms of radiation and convection in heating, ventilating, and air conditioning systems that are designed to provide acceptable thermal, acoustic, and air quality conditions within occupied spaces.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:1821369

IMAT graphics manual

NASA Technical Reports Server (NTRS)

Stockwell, Alan E.; Cooper, Paul A.

1991-01-01

The Integrated Multidisciplinary Analysis Tool (IMAT) consists of a menu driven executive system coupled with a relational database which links commercial structures, structural dynamics and control codes. The IMAT graphics system, a key element of the software, provides a common interface for storing, retrieving, and displaying graphical information. The IMAT Graphics Manual shows users of commercial analysis codes (MATRIXx, MSC/NASTRAN and I-DEAS) how to use the IMAT graphics system to obtain high quality graphical output using familiar plotting procedures. The manual explains the key features of the IMAT graphics system, illustrates their use with simple step-by-step examples, and provides a reference for users who wish to take advantage of the flexibility of the software to customize their own applications.

High success rates of sedation-free brain MRI scanning in young children using simple subject preparation protocols with and without a commercial mock scanner–the Diabetes Research in Children Network (DirecNet) experience

PubMed Central

Barnea-Goraly, Naama; Weinzimer, Stuart A.; Mauras, Nelly; Beck, Roy W.; Marzelli, Matt J.; Mazaika, Paul K.; Aye, Tandy; White, Neil H.; Tsalikian, Eva; Fox, Larry; Kollman, Craig; Cheng, Peiyao; Reiss, Allan L.

2013-01-01

Background The ability to lie still in an MRI scanner is essential for obtaining usable image data. To reduce motion, young children are often sedated, adding significant cost and risk. Objective We assessed the feasibility of using a simple and affordable behavioral desensitization program to yield high-quality brain MRI scans in sedation-free children. Materials and methods 222 children (4–9.9 years), 147 with type 1 diabetes and 75 age-matched non-diabetic controls, participated in a multi-site study focused on effects of type 1 diabetes on the developing brain. T1-weighted and diffusion-weighted imaging (DWI) MRI scans were performed. All children underwent behavioral training and practice MRI sessions using either a commercial MRI simulator or an inexpensive mock scanner consisting of a toy tunnel, vibrating mat, and video player to simulate the sounds and feel of the MRI scanner. Results 205 children (92.3%), mean age 7±1.7 years had high-quality T1-W scans and 174 (78.4%) had high-quality diffusion-weighted scans after the first scan session. With a second scan session, success rates were 100% and 92.5% for T1-and diffusion-weighted scans, respectively. Success rates did not differ between children with type 1 diabetes and children without diabetes, or between centers using a commercial MRI scan simulator and those using the inexpensive mock scanner. Conclusion Behavioral training can lead to a high success rate for obtaining high-quality T1-and diffusion-weighted brain images from a young population without sedation. PMID:24096802

Suitability of Commercial Transport Media for Biological Pathogens under Nonideal Conditions

PubMed Central

Hubbard, Kyle; Pellar, Gregory; Emanuel, Peter

2011-01-01

There is extensive data to support the use of commercial transport media as a stabilizer for known clinical samples; however, there is little information to support their use outside of controlled conditions specified by the manufacturer. Furthermore, there is no data to determine the suitability of said media for biological pathogens, specifically those of interest to the US military. This study evaluates commercial off-the-shelf (COTS) transport media based on sample recovery, viability, and quality of nucleic acids and peptides for nonpathogenic strains of Bacillus anthracis, Yersinia pestis, and Venezuelan equine encephalitis virus, in addition to ricin toxin. Samples were stored in COTS, PBST, or no media at various temperatures over an extended test period. The results demonstrate that COTS media, although sufficient for the preservation of nucleic acid and proteinaceous material, are not capable of maintaining an accurate representation of biothreat agents at the time of collection. PMID:22121364

First Worldwide Proficiency Study on Variable-Number Tandem-Repeat Typing of Mycobacterium tuberculosis Complex Strains

PubMed Central

de Beer, Jessica L.; Kremer, Kristin; Ködmön, Csaba; Supply, Philip

2012-01-01

Although variable-number tandem-repeat (VNTR) typing has gained recognition as the new standard for the DNA fingerprinting of Mycobacterium tuberculosis complex (MTBC) isolates, external quality control programs have not yet been developed. Therefore, we organized the first multicenter proficiency study on 24-locus VNTR typing. Sets of 30 DNAs of MTBC strains, including 10 duplicate DNA samples, were distributed among 37 participating laboratories in 30 different countries worldwide. Twenty-four laboratories used an in-house-adapted method with fragment sizing by gel electrophoresis or an automated DNA analyzer, nine laboratories used a commercially available kit, and four laboratories used other methods. The intra- and interlaboratory reproducibilities of VNTR typing varied from 0% to 100%, with averages of 72% and 60%, respectively. Twenty of the 37 laboratories failed to amplify particular VNTR loci; if these missing results were ignored, the number of laboratories with 100% interlaboratory reproducibility increased from 1 to 5. The average interlaboratory reproducibility of VNTR typing using a commercial kit was better (88%) than that of in-house-adapted methods using a DNA analyzer (70%) or gel electrophoresis (50%). Eleven laboratories using in-house-adapted manual typing or automated typing scored inter- and intralaboratory reproducibilities of 80% or higher, which suggests that these approaches can be used in a reliable way. In conclusion, this first multicenter study has documented the worldwide quality of VNTR typing of MTBC strains and highlights the importance of international quality control to improve genotyping in the future. PMID:22170917

NASA. Langley Research Center dry powder towpreg system

NASA Technical Reports Server (NTRS)

Baucom, Robert M.; Marchello, Joseph M.

1990-01-01

Dry powder polymer impregnated carbon fiber tows were produced for preform weaving and composite materials molding applications. In the process, fluidized powder is deposited on spread tow bundles and melted on the fibers by radiant heating to adhere the polymer to the fiber. Unit design theory and operating correlations were developed to provide the basis for scale up of the process to commercial operation. Special features of the operation are the pneumatic tow spreader, fluidized bed, resin feeder, and quality control system. Bench scale experiments, at tow speeds up to 50 cm/sec, demonstrated that process variables can be controlled to produce weavable LARC-TPI carbon fiber towpreg. The towpreg made by the dry powder process was formed into unidirectional fiber moldings and was woven and molded into preform material of good quality.

Manufacturing, characterization and control of cell-based medicinal products: challenging paradigms toward commercial use.

PubMed

Salmikangas, Paula; Menezes-Ferreira, Margarida; Reischl, Ilona; Tsiftsoglou, Asterios; Kyselovic, Jan; Borg, John Joseph; Ruiz, Sol; Flory, Egbert; Trouvin, Jean-Hugues; Celis, Patrick; Ancans, Janis; Timon, Marcos; Pante, Guido; Sladowski, Dariusz; Lipnik-Stangelj, Metoda; Schneider, Christian K

2015-01-01

During the past decade, a large number of cell-based medicinal products have been tested in clinical trials for the treatment of various diseases and tissue defects. However, licensed products and those approaching marketing authorization are still few. One major area of challenge is the manufacturing and quality development of these complex products, for which significant manipulation of cells might be required. While the paradigms of quality, safety and efficacy must apply also to these innovative products, their demonstration may be demanding. Demonstration of comparability between production processes and batches may be difficult for cell-based medicinal products. Thus, the development should be built around a well-controlled manufacturing process and a qualified product to guarantee reproducible data from nonclinical and clinical studies.

Preventing and controlling foodborne disease in commercial and institutional food service settings: a systematic review of published intervention studies.

PubMed

Viator, Catherine; Blitstein, Jonathan; Brophy, Jenna E; Fraser, Angela

2015-02-01

This study reviews the current literature on behavioral and environmental food safety interventions conducted in commercial and institutional food service settings. A systematic search of the published literature yielded 268 candidate articles, from which a set of 23 articles reporting intervention outcomes was retained for evaluation. A categorization of measured outcomes is reported; studies addressed multiple outcomes ranging from knowledge, attitudes, and behavior of personal hygiene and food safety to management practices and disease rates and outbreaks. This study also investigates the quality of reported research methods used to evaluate the effectiveness of the interventions, using a nine-point quality index adapted by the authors. The observed scores suggest that there are opportunities to improve the design and reporting of research in the field of foodborne disease prevention as it applies to food safety interventions that target the food service industry. The aim is to aid researchers in this area to design higher quality studies and to produce clearer and more useful reports of their research. In turn, this can help to create a more complete evidence base that can be used to continually improve interventions in this domain.

Control of Disturbing Loads in Residential and Commercial Buildings via Geometric Algebra

PubMed Central

2013-01-01

Many definitions have been formulated to represent nonactive power for distorted voltages and currents in electronic and electrical systems. Unfortunately, no single universally suitable representation has been accepted as a prototype for this power component. This paper defines a nonactive power multivector from the most advanced multivectorial power theory based on the geometric algebra (GA). The new concept can have more importance on harmonic loads compensation, identification, and metering, between other applications. Likewise, this paper is concerned with a pioneering method for the compensation of disturbing loads. In this way, we propose a multivectorial relative quality index   δ~ associated with the power multivector. It can be assumed as a new index for power quality evaluation, harmonic sources detection, and power factor improvement in residential and commercial buildings. The proposed method consists of a single-point strategy based of a comparison among different relative quality index multivectors, which may be measured at the different loads on the same metering point. The comparison can give pieces of information with magnitude, direction, and sense on the presence of disturbing loads. A numerical example is used to illustrate the clear capabilities of the suggested approach. PMID:24260017

Control of disturbing loads in residential and commercial buildings via geometric algebra.

PubMed

Castilla, Manuel-V

2013-01-01

Many definitions have been formulated to represent nonactive power for distorted voltages and currents in electronic and electrical systems. Unfortunately, no single universally suitable representation has been accepted as a prototype for this power component. This paper defines a nonactive power multivector from the most advanced multivectorial power theory based on the geometric algebra (GA). The new concept can have more importance on harmonic loads compensation, identification, and metering, between other applications. Likewise, this paper is concerned with a pioneering method for the compensation of disturbing loads. In this way, we propose a multivectorial relative quality index δ(~) associated with the power multivector. It can be assumed as a new index for power quality evaluation, harmonic sources detection, and power factor improvement in residential and commercial buildings. The proposed method consists of a single-point strategy based of a comparison among different relative quality index multivectors, which may be measured at the different loads on the same metering point. The comparison can give pieces of information with magnitude, direction, and sense on the presence of disturbing loads. A numerical example is used to illustrate the clear capabilities of the suggested approach.

Effect of vertical active vibration isolation on tracking performance and on ride qualities

NASA Technical Reports Server (NTRS)

Dimasi, F. P.; Allen, R. E.; Calcaterra, P. C.

1972-01-01

An investigation to determine the effect on pilot performance and comfort of an active vibration isolation system for a commercial transport pilot seat is reported. The test setup consisted of: a hydraulic shaker which produced random vertical vibration inputs; the active vibration isolation system; the pilot seat; the pilot control wheel and column; the side-arm controller; and a two-axis compensatory tracking task. The effects of various degrees of pilot isolation on short-term (two-minute) tracking performance and comfort were determined.

Citrus pulp and wheat straw silage as an ingredient in lamb diets: effects on growth and carcass and meat quality.

PubMed

Scerra, V; Caparra, P; Foti, F; Lanza, M; Priolo, A

2001-04-01

Twenty "Merinizzata Italiana" lambs were introduced to two experimental diets. Ten animals (five males and five females, control group) received the traditional diet that is supplied by farmers in southern Italy, which comprised of oat hay ad libitum and commercial concentrate. The second group (the same number of lambs, silage group) received citrus pulp and wheat straw silage ad libitum and 70% of the commercial concentrate supplied to the control group. The animals were slaughtered after 80 days of feeding and carcass and some meat quality parameters were measured. No differences were observed for live weight between treatments, and carcass weights were similar for the two diets, but with obvious differences between sexes. Animals on silage produced carcasses with a better muscular conformation and with a lower fatness score (P<0.05). Subcutaneous fat colour was influenced by sex, being lighter in the female carcasses (P<0.05). Dissection of different anatomical parts showed a higher percentage of lean and a lower proportion of fat in silage samples compared to control ones. Ultimate pH was highly affected by sex being higher in the samples from male lambs (P<0.01), but was unaffected by diet treatment. Diet tended to affect meat shear force value which was lower in the silage samples, although, samples from all the animals were extremely tender. Meat from silage samples had a higher water content (P<0.05). Overall, in our experimental conditions, the use of citrus pulp silage seemed to be economically convenient for producing animals with substantially unmodified carcass and meat quality characteristics.

Muffins Elaborated with Optimized Monoglycerides Oleogels: From Solid Fat Replacer Obtention to Product Quality Evaluation.

PubMed

Giacomozzi, Anabella S; Carrín, María E; Palla, Camila A

2018-06-01

This study demonstrates the effectiveness of using oleogels from high oleic sunflower oil (HOSO) and monoglycerides as solid fat replacers in a sweet bakery product. Firstly, a methodology to obtain oleogels with desired properties based on mathematical models able to describe relationships between process and product characteristics variables followed by multi-objective optimization was applied. Later, muffins were prepared with the optimized oleogels and their physicochemical and textural properties were compared with those of muffins formulated using a commercial margarine (Control) or only HOSO. Furthermore, the amount of oil released from muffins over time (1, 7, and 10 days) was measured to evaluate their stability. The replacement of commercial margarine with the optimized oleogels in muffin formulation led to the obtention of products with greater spreadability, higher specific volume, similar hardness values, and a more connected and homogeneous crumb structure. Moreover, these products showed a reduction of oil migration of around 50% in contrast to the Control muffins after 10 days of storage, which indicated that the optimized oleogels can be used satisfactorily to decrease oil loss in this sweet baked product. Fat replacement with the optimized monoglycerides oleogels not only had a positive impact on the quality of the muffins, but also allowed to improve their nutritional profile (without trans fat and low in saturated fat). The food industry demands new ways to reduce the use of saturated and trans fats in food formulations. To contribute to this search, oleogels from high oleic sunflower oil and saturated monoglycerides were prepared under optimized conditions in order to obtain a product with similar functionality to margarine, and its potential application as a semisolid fat ingredient in muffins was evaluated. Muffins formulated with oleogels showed an improved quality compare with those obtained using a commercial margarine with the added benefit of a healthier nutritional profile. © 2018 Institute of Food Technologists®.

Assessing the Quality and Potential Efficacy of Commercial Extracts of Rhodiola rosea L. by Analyzing the Salidroside and Rosavin Content and the Electrophysiological Activity in Hippocampal Long-Term Potentiation, a Synaptic Model of Memory.

PubMed

Dimpfel, Wilfried; Schombert, Leonie; Panossian, Alexander G

2018-01-01

Rhodiola rosea L. roots and rhizome extracts are active ingredients in adaptogenic herbal medicinal products (HMP) and dietary supplements for temporary relief of symptoms of stress, such as fatigue and weakness. R. rosea extract has a stimulating effect on the CNS, suggesting potential benefits on cognitive functions, memory, learning, and attention. The reproducible efficacy and quality of preparations of the underground parts of R. rosea depend on the highly variable content of the active markers, salidroside and rosavin, which affect the quality of HMP and dietary supplements. However, it is not clear which analytical markers are important for assessing the efficacy of R. rosea preparations intended for use in aging-induced mild cognitive disorders, such as attenuated memory, attention, and learning. Furthermore, the activity of various commercial R. rosea extracts has not been correlated with their content. Here, the biological activities of salidroside, rosavin, and seven commercial extracts of underground parts of R. rosea were assessed using a synaptic model of memory: long-term potentiation (LTP) of synaptic transmission in hippocampus slices. A high degree of variation in the content of all active markers was observed. One extract from China lacked rosavin, and there was even variation in the extracts from the Altai geographic region. In vitro , rosavin, salidroside and all tested R. rosea extracts potentiated electric stimulation of an intra-hippocampal electric circuit, which resulted in higher responses of the pyramidal cells in isolated hippocampus slices. Rosavin was more active at higher concentrations than salidroside; while, salidroside was more effective at lower concentrations. The highest content of both active markers was found in the extracts that were active at the lowest concentrations tested; while, some extracts contained some other compounds that presumably reduced the efficacy due to antagonistic interactions. Standardized content of active markers is necessary for the quality control of herbal preparations containing R. rosea extracts, but insufficient for assessment of their potential efficacy. Additional bioassays are needed to assure the reproducible pharmacological activity of R. rosea extracts; therefore, the LTP of synaptic transmission in hippocampus slices may serve as a validation tool for the quality control of R. rosea extracts.

Particle loading rates for HVAC filters, heat exchangers, and ducts.

PubMed

Waring, M S; Siegel, J A

2008-06-01

The rate at which airborne particulate matter deposits onto heating, ventilation, and air-conditioning (HVAC) components is important from both indoor air quality (IAQ) and energy perspectives. This modeling study predicts size-resolved particle mass loading rates for residential and commercial filters, heat exchangers (i.e. coils), and supply and return ducts. A parametric analysis evaluated the impact of different outdoor particle distributions, indoor emission sources, HVAC airflows, filtration efficiencies, coils, and duct system complexities. The median predicted residential and commercial loading rates were 2.97 and 130 g/m(2) month for the filter loading rates, 0.756 and 4.35 g/m(2) month for the coil loading rates, 0.0051 and 1.00 g/month for the supply duct loading rates, and 0.262 g/month for the commercial return duct loading rates. Loading rates are more dependent on outdoor particle distributions, indoor sources, HVAC operation strategy, and filtration than other considered parameters. The results presented herein, once validated, can be used to estimate filter changing and coil cleaning schedules, energy implications of filter and coil loading, and IAQ impacts associated with deposited particles. The results in this paper suggest important factors that lead to particle deposition on HVAC components in residential and commercial buildings. This knowledge informs the development and comparison of control strategies to limit particle deposition. The predicted mass loading rates allow for the assessment of pressure drop and indoor air quality consequences that result from particle mass loading onto HVAC system components.

Economic burden of sarcoidosis in a commercially-insured population in the United States.

PubMed

Rice, J Bradford; White, Alan; Lopez, Andrea; Conway, Alexandra; Wagh, Aneesha; Nelson, Winnie W; Philbin, Michael; Wan, George J

2017-10-01

Sarcoidosis is a multi-system inflammatory disorder characterized by the presence of non-caseating granulomas in involved organs. Patients with sarcoidosis have a reduced quality-of-life and are at an increased risk for several comorbidities. Little is known about the direct and indirect cost of sarcoidosis following the initial diagnosis. To provide an estimate of the healthcare resource utilization (HCRU) and costs borne by commercial payers for sarcoidosis patients in the US. Patients with a first diagnosis of sarcoidosis between January 1, 1998 and March 31, 2015 ("index date") were selected from a de-identified privately-insured administrative claims database. Sarcoidosis patients were required to have continuous health plan enrollment 12 months prior to and following their index dates. Propensity-score (1:1) matching of sarcoidosis patients with non-sarcoidosis controls was carried out based on a logistic regression of baseline characteristics. Burden of HCRU and work loss (disability days and medically-related absenteeism) were compared between the matched groups over the 12-month period following the index date ("outcome period"). A total of 7,119 sarcoidosis patients who met the selection criteria were matched with a control. Overall, commercial payers incurred $19,714 in mean total annual healthcare costs per sarcoidosis patient. The principle cost drivers were outpatient visits ($9,050 2015 USD, 46%) and inpatient admissions ($6,398, 32%). Relative to controls, sarcoidosis patients had $5,190 (36%) higher total healthcare costs ($19,714 vs $14,524; p < 0.001). Sarcoidosis patients also had significantly more work loss days (15.9 vs 11.3; p < 0.001) and work loss costs ($3,288 vs $2,527; p < 0.001) than matched controls. Sarcoidosis imposes an estimated total direct medical cost of $1.3-$8.7 billion to commercial payers, and an indirect cost of $0.2-$1.5 billion to commercial payers in work loss. Sarcoidosis imposes a significant economic burden to payers in the first year following diagnosis.

ACOs Holding Commercial Contracts Are Larger And More Efficient Than Noncommercial ACOs

PubMed Central

Peiris, David; Phipps-Taylor, Madeleine C.; Stachowski, Courtney A.; Kao, Lee-Sien; Shortell, Stephen M.; Lewis, Valerie A.; Rosenthal, Meredith B.; Colla, Carrie H.

2016-01-01

Accountable care organizations (ACOs) have diverse contracting arrangements and have displayed wide variations in their performance. Using data from national surveys of 399 ACOs, we examined differences between the 228 commercial ACOs (those with commercial payer contracts) and the 171 noncommercial ACOs (those with only public contracts, such as with Medicare or Medicaid). Commercial ACOs were significantly larger and more integrated with hospitals, and had lower benchmark expenditures and higher quality scores, compared to noncommercial ACOs. Among all of the ACOs, there was low uptake of quality and efficiency activities. However, commercial ACOs reported more use of disease monitoring tools, patient satisfaction data, and quality improvement methods than did noncommercial ACOs. Few ACOs reported having high-level performance monitoring capabilities. About two-thirds of the ACOs had established processes for distributing any savings accrued, and these ACOs allocated approximately the same amount of savings to the ACOs themselves, participating member organizations, and physicians. Our findings demonstrate that ACO delivery systems remain at a nascent stage. Structural differences between commercial and noncommercial ACOs are important factors to consider as public policy efforts continue to evolve. PMID:27702959

A Community Standard Format for the Representation of Protein Affinity Reagents*

PubMed Central

Gloriam, David E.; Orchard, Sandra; Bertinetti, Daniela; Björling, Erik; Bongcam-Rudloff, Erik; Borrebaeck, Carl A. K.; Bourbeillon, Julie; Bradbury, Andrew R. M.; de Daruvar, Antoine; Dübel, Stefan; Frank, Ronald; Gibson, Toby J.; Gold, Larry; Haslam, Niall; Herberg, Friedrich W.; Hiltke, Tara; Hoheisel, Jörg D.; Kerrien, Samuel; Koegl, Manfred; Konthur, Zoltán; Korn, Bernhard; Landegren, Ulf; Montecchi-Palazzi, Luisa; Palcy, Sandrine; Rodriguez, Henry; Schweinsberg, Sonja; Sievert, Volker; Stoevesandt, Oda; Taussig, Michael J.; Ueffing, Marius; Uhlén, Mathias; van der Maarel, Silvère; Wingren, Christer; Woollard, Peter; Sherman, David J.; Hermjakob, Henning

2010-01-01

Protein affinity reagents (PARs), most commonly antibodies, are essential reagents for protein characterization in basic research, biotechnology, and diagnostics as well as the fastest growing class of therapeutics. Large numbers of PARs are available commercially; however, their quality is often uncertain. In addition, currently available PARs cover only a fraction of the human proteome, and their cost is prohibitive for proteome scale applications. This situation has triggered several initiatives involving large scale generation and validation of antibodies, for example the Swedish Human Protein Atlas and the German Antibody Factory. Antibodies targeting specific subproteomes are being pursued by members of Human Proteome Organisation (plasma and liver proteome projects) and the United States National Cancer Institute (cancer-associated antigens). ProteomeBinders, a European consortium, aims to set up a resource of consistently quality-controlled protein-binding reagents for the whole human proteome. An ultimate PAR database resource would allow consumers to visit one on-line warehouse and find all available affinity reagents from different providers together with documentation that facilitates easy comparison of their cost and quality. However, in contrast to, for example, nucleotide databases among which data are synchronized between the major data providers, current PAR producers, quality control centers, and commercial companies all use incompatible formats, hindering data exchange. Here we propose Proteomics Standards Initiative (PSI)-PAR as a global community standard format for the representation and exchange of protein affinity reagent data. The PSI-PAR format is maintained by the Human Proteome Organisation PSI and was developed within the context of ProteomeBinders by building on a mature proteomics standard format, PSI-molecular interaction, which is a widely accepted and established community standard for molecular interaction data. Further information and documentation are available on the PSI-PAR web site. PMID:19674966

Quality of 99mTcO4- from 99Mo Produced by 100Mo(n,2n)99Mo

NASA Astrophysics Data System (ADS)

Nagai, Yasuki; Nakahara, Yuto; Kawabata, Masako; Hatsukawa, Yuichi; Hashimoto, Kazuyuki; Saeki, Hideya; Motoishi, Shoji; Ohta, Akio; Shiina, Takayuki; Kawauchi, Yukimasa

2017-05-01

The pharmaceutical quality of 99mTc pertechnetate solution obtained from 99Mo, the 100Mo(n,2n) reaction product, was investigated for the first time with an emphasis on the nonradioactive Mo content and endotoxin concentration. They were less than the tolerance dose given in international guidelines and the established upper limit in an international pharmacopoeia, respectively. Four other quality control tests commonly used for a commercially available 99mTc pertechnetate solution also demonstrated to meet the United States Pharmacopeia requirements. The results strongly support that the thermochromatographic separation method used to separate 99mTc from 99Mo can be a promising substitute for the fission product 99Mo.

Metabolic Profiling of Hoodia, Chamomile, Terminalia Species and Evaluation of Commercial Preparations Using Ultrahigh-Performance Liquid Chromatography Quadrupole-Time-of-Flight Mass Spectrometry.

PubMed

Avula, Bharathi; Wang, Yan-Hong; Isaac, Giorgis; Yuk, Jimmy; Wrona, Mark; Yu, Kate; Khan, Ikhlas A

2017-11-01

Ultrahigh-performance liquid chromatography quadrupole-time-of-flight mass spectrometry (UHPLC-QToF-MS) profiling was used for the identification of marker compounds and generation of metabolic patterns that could be interrogated using chemometric modeling software. UHPLC-QToF-MS was used to generate comprehensive fingerprints of three botanicals ( Hoodia, Terminalia , and chamomile), each having different classes of compounds. Detection of a broad range of ions was carried out in full scan mode in both positive and negative modes over the range m/z 100-1700 using high-resolution mass spectrometry. Multivariate statistical analysis was used to extract relevant chemical information from the data to easily differentiate between Terminalia species, chamomile varieties, and quality control of Hoodia products. Using nontargeted analysis, identification of 37 compounds contributed to the differences between Terminalia species, 26 flavonoids were identified to show the differences between German and Roman chamomile, and 43 pregnane glycosides were identified from Hoodia gordonii samples. The UHPLC-QToF-MS-based chemical fingerprinting with principal component analysis was able to correctly distinguish botanicals and their commercial products. This work can be used as a basis to assure the quality of botanicals and commercial products. Georg Thieme Verlag KG Stuttgart · New York.

Food-poisoning and commercial air travel.

PubMed

McMullan, R; Edwards, P J; Kelly, M J; Millar, B C; Rooney, P J; Moore, J E

2007-09-01

With the introduction of budget airlines and greater competitiveness amongst all airlines, air travel has now become an extremely popular form of travel, presenting its own unique set of risks from food poisoning. Foodborne illness associated with air travel is quite uncommon in the modern era. However, when it occurs, it may have serious implications for passengers and when crew are affected, has the potential to threaten safety. Quality, safe, in-flight catering relies on high standards of food preparation and storage; this applies at the airport kitchens (or at subcontractors' facilities), on the aircraft and in the transportation vehicles which carry the food from the ground source to the aircraft. This is especially challenging in certain countries. Several foodborne outbreaks have been recorded by the airline industry as a result of a number of different failures of these systems. These have provided an opportunity to learn from past mistakes and current practice has, therefore, reached such a standard so as to minimise risk of failures of this kind. This review examines: (i) the origin of food safety in modern commercial aviation; (ii) outbreaks which have occurred previously relating to aviation travel; (iii) the microbiological quality of food and water on board commercial aircraft; and (iv) how Hazard Analysis Critical Control Points may be employed to maintain food safety in aviation travel.

Comparison of architect I 2000 for determination of cyclosporine with axsym.

PubMed

Serdarevic, Nafija; Zunic, Lejla

2012-12-01

Cyclosporine has been shown effective drug in suppressing acute rejection in recipients of allograft organ transplants. The cyclosporine concentration of 96 blood samples was determined using CMIA (chemiluminesecent microparticle immnoassay) Architect i 2000 and FPIA (fluorescence polarization immunoassay) AxSYM Abbott diagnostic. All patients have transplantation of kidneys and were hospitalized at Department of Nephrology at the Clinical center of University of Sarajevo. The reference serum range of cyclosporine for kidney organ transplantation for maintenance lies between 50 and 150 ng/mL. The quality control, precision and accurancy of Architect i 2000 were assessed. The quality control was done using quality control serums for low (= 91 ng/mL), medium (= 328 ng/mL) and high (= 829 ng/mL). We have used commercial BIORAD controls and got reproducibility CV 5.83 % to 13 % for Architect i 2000. It was established that the main difference between Architect i 2000 and AxSYM and it was statistically significant for P < 0.05 according to Student t-test. Correlation coefficient was r = 0.903. The CMIA Architect assay has significant reduced cyclosporine metabolite interference relative to other immunoassay and is a convenient and sensitive automated method to measure cyclosporine in whole blood.

Application of genotypic and phenotypic analyses to commercial probiotic strain identity and relatedness.

PubMed

Yeung, P S M; Kitts, C L; Cano, R; Tong, P S; Sanders, M E

2004-01-01

The objective of this study was to generate strain-specific genomic patterns of a bank of 67 commercial and reference probiotic strains, with a focus on probiotic lactobacilli. Pulsed-field gel electrophoresis (PFGE) was used as the primary method for strain differentiation. This method was compared with carbohydrate fermentation analysis. To supplement visual comparison, PFGE patterns were analysed quantitatively by cluster analysis using unweighted pair group method with arithmetic averages. SmaI, NotI and XbaI were found to effectively generate clear and easy-to-interpret PFGE patterns of a range of probiotic strains. Some probiotic strains from different sources shared highly similar PFGE patterns. Results document the value of genotypic strain identification methods, combined with phenotypic methods, for determining probiotic strain identity and relatedness. No correlation was found between relatedness determined by carbohydrate fermentation profiles alone compared with PFGE analysis alone. Some commercial strains are probably derived from similar sources. This approach is valuable to the probiotic industry to develop commercial strain identification patterns, to provide quality control of strain manufacturing production runs, to track use of protected strains and to determine the relatedness among different research and commercial probiotic strains.

Chemical profiling and quantification of monacolins and citrinin in red yeast rice commercial raw materials and dietary supplements using liquid chromatography-accurate QToF mass spectrometry: Chemometrics application.

PubMed

Avula, Bharathi; Cohen, Pieter A; Wang, Yan-Hong; Sagi, Satyanarayanaraju; Feng, Wei; Wang, Mei; Zweigenbaum, Jerry; Shuangcheng, Ma; Khan, Ikhlas A

2014-11-01

Red yeast rice (RYR) is prepared by fermenting rice with various strains of the yeast Monascus spp of the Aspergillaceae family. Depending on the Monascus strains and the fermentation conditions, the products may contain monacolins, pigments and citrinin as secondary metabolites. Authentic and commercial RYR samples were analyzed using UHPLC-DAD-QToF-MS for monacolins, pigments and citrinin. A separation by UHPLC was achieved using a reversed-phase column and a gradient of water/acetonitrile each containing formic acid as the mobile phase. Accurate mass QToF spectrometry was used to distinguish isobaric monacolins. Principle component analysis (PCA), a chemometric technique was used to discriminate between authentic RYR, commercial RYR raw materials and dietary supplements. Three authentic RYR samples, 31 commercial RYR raw materials and 14 RYR dietary supplements were analyzed. Monacolin K content in 600mg of authentic RYR samples ranged from 1.2mg to 1.38mg. Amounts of monacolin K in dietary supplements labeled as containing 600mg of RYR varied more than 40-fold from 0.03mg to 2.18mg. Monacolin K content of dietary supplements labeled as containing 1200mg RYR varied more than 20-fold from 0.22mg to 5.23mg. In addition to large variations in quantity of monacolin K found in dietary supplements, RYR dietary supplements contained ratios of monacolins that differed significantly from authentic samples. The results indicated that RYR commercial products are of variable quality and the analytical method is suitable for quality control testing of a variety of RYR products. Copyright © 2014 Elsevier B.V. All rights reserved.

Silvicultural practices (commercial thinning) are influencing the health of natural pine stands in eastern California

Treesearch

Gary O. Fiddler; Dennis R. Hart; Philip M. McDonald; Susan J. Frankel

1995-01-01

Overstocked 70- to 90-year-old stands of ponderosa pine on medium to low quality sites were thinned in 1980 to 40, 55, and 70 percent of normal basal area and compareh to an unthinned control. Mortality was recorded annually. Growth was measured every 5 years from 1980 to 1994. After 15 years, mortality, primarily from bark beetles and annosus root disease, was reduced...

Quality Control of Direct Molecular Diagnostics for Methicillin-Resistant Staphylococcus aureus▿

PubMed Central

van Belkum, Alex; Niesters, Hubert G. M.; MacKay, William G.; van Leeuwen, Willem B.

2007-01-01

Ten samples containing various amounts of methicillin-resistant Staphylococcus aureus (MRSA), methicillin-susceptible S. aureus, methicillin-resistant Staphylococcus epidermidis (MRSE), and combinations thereof were distributed to 51 laboratories for molecular diagnostics testing. Samples containing 102 to 103 MRSA cells were frequently reported to be negative. MRSE samples were scored as negative by all commercial tests but by only two out of three in-house tests. PMID:17581936

Reprocessing and reuse of waste tire rubber to solve air-quality related problems

USGS Publications Warehouse

Lehmann, C.M.B.; Rostam-Abadi, M.; Rood, M.J.; Sun, Jielun

1998-01-01

There is a potential for using waste tire rubber to make activated-carbon adsorbents for air-quality control applications. Such an approach provides a recycling path for waste tires and the production of new adsorbents from a low-cost waste material. Tire-derived activated carbons (TDACs) were prepared from waste tires. The resulting products are generally mesoporous, with N2-BET specific surface areas ranging from 239 to 1031 m2/g. TDACs were tested for their ability to store natural gas and remove organic compounds and mercury species from gas streams. TDACs are able to achieve 36% of the recommended adsorbed natural gas (methane) storage capacity for natural-gas-fueled vehicles. Equilibrium adsorption capacities for CH4 achieved by TDACs are comparable to Calgon BPL, a commercially available activated-carbon adsorbent. The acetone adsorption capacity for a TDAC is 67% of the adsorption capacity achieved by BPL at 1 vol % acetone. Adsorption capacities of mercury in simulated flue-gas streams are, in general, larger than adsorption capacities achieved by coal-derived activated carbons (CDACs) and BPL. Although TDACs may not perform as well as commercial adsorbents in some air pollution control applications, the potential lower cost of TDACS should be considered when evaluating economics.

Irradiation effect on bulgogi sauce for making commercial Korean traditional meat product, bulgogi

NASA Astrophysics Data System (ADS)

Jo, C.; Kim, D. H.; Shin, M. G.; Kang, I. J.; Byun, M. W.

2003-12-01

Gamma-irradiated sauce of bulogogi, Korean traditional meat products, was compared with heat-pasteurized one to enhance its safety, quality, and commercial availability. The sauce is usually sold in refrigerated state with 2-7 days of self-life or heat-sterilized and sold in room temperature for a year. Raw vegetables, fruits and soy sauce for sauce making were highly contaminated by thermophillic microorganisms (totally 2.13×10 6 CFU/g) and coliform bacteria (totally 5.90×10 4 CFU/g) at the initial stage. Heat treatment (100°C for 30 min) was effective to control coliform and microbes counted from Salmonella-Shigella selective agar in the sauce but not on thermophillic microorganisms, resulting in a rapid spoilage after 2 weeks at 20°C. Gamma irradiation reduced the level of thermophillic microorganisms and the spoilage was prevented during storage for 4 weeks at 20°C. Protease activity of the sauce was significantly reduced by heat treatment while was not changed by irradiation at 2.5, 5.0, and 10 kGy. Sensory evaluation showed that the irradiation was better in color than nonirradiated control or heat-treated sample. Results indicate that low dose irradiation (2.5-5.0 kGy) is effective to ensure safety of bulgogi sauce with acceptable sensory quality.

Impact of commercial housing systems and nutrient and energy intake on laying hen performance and egg quality parameters1

PubMed Central

Karcher, D. M.; Jones, D. R.; Abdo, Z.; Zhao, Y.; Shepherd, T. A.; Xin, H.

2015-01-01

The US egg industry is exploring alternative housing systems for laying hens. However, limited published research related to cage-free aviary systems and enriched colony cages exists related to production, egg quality, and hen nutrition. The laying hen's nutritional requirements and resulting productivity are well established with the conventional cage system, but diminutive research is available in regards to alternative housing systems. The restrictions exist with limited availability of alternative housing systems in research settings and the considerable expense for increased bird numbers in a replicate due to alternative housing system design. Therefore, the objective of the current study was to evaluate the impact of nutrient and energy intake on production and egg quality parameters from laying hens housed at a commercial facility. Lohmann LSL laying hens were housed in three systems: enriched colony cage, cage-free aviary, and conventional cage at a single commercial facility. Daily production records were collected along with dietary changes during 15 production periods (28-d each). Eggs were analyzed for shell strength, shell thickness, Haugh unit, vitelline membrane properties, and egg solids each period. An analysis of covariance (ANCOVA) coupled with a principal components analysis (PCA) approach was utilized to assess the impact of nutritional changes on production parameters and monitored egg quality factors. The traits of hen-day production and mortality had a response only in the PCA 2 direction. This finds that as house temperature and Met intake increases, there is an inflection point at which hen-day egg production is negatively effected. Dietary changes more directly influenced shell parameters, vitelline membrane parameters, and egg total solids as opposed to laying hen housing system. Therefore, further research needs to be conducted in controlled research settings on laying hen nutrient and energy intake in the alternative housing systems and resulting impact on egg quality measures. PMID:25630672

Impact of commercial housing systems and nutrient and energy intake on laying hen performance and egg quality parameters.

PubMed

Karcher, D M; Jones, D R; Abdo, Z; Zhao, Y; Shepherd, T A; Xin, H

2015-03-01

The US egg industry is exploring alternative housing systems for laying hens. However, limited published research related to cage-free aviary systems and enriched colony cages exists related to production, egg quality, and hen nutrition. The laying hen's nutritional requirements and resulting productivity are well established with the conventional cage system, but diminutive research is available in regards to alternative housing systems. The restrictions exist with limited availability of alternative housing systems in research settings and the considerable expense for increased bird numbers in a replicate due to alternative housing system design. Therefore, the objective of the current study was to evaluate the impact of nutrient and energy intake on production and egg quality parameters from laying hens housed at a commercial facility. Lohmann LSL laying hens were housed in three systems: enriched colony cage, cage-free aviary, and conventional cage at a single commercial facility. Daily production records were collected along with dietary changes during 15 production periods (28-d each). Eggs were analyzed for shell strength, shell thickness, Haugh unit, vitelline membrane properties, and egg solids each period. An analysis of covariance (ANCOVA) coupled with a principal components analysis (PCA) approach was utilized to assess the impact of nutritional changes on production parameters and monitored egg quality factors. The traits of hen-day production and mortality had a response only in the PCA 2 direction. This finds that as house temperature and Met intake increases, there is an inflection point at which hen-day egg production is negatively effected. Dietary changes more directly influenced shell parameters, vitelline membrane parameters, and egg total solids as opposed to laying hen housing system. Therefore, further research needs to be conducted in controlled research settings on laying hen nutrient and energy intake in the alternative housing systems and resulting impact on egg quality measures. © The Author 2015. Published by Oxford University Press on behalf of Poultry Science Association.

Development and Validation of a Combined Methodology for Assessing the Total Quality Control of Herbal Medicinal Products – Application to Oleuropein Preparations

PubMed Central

Lemonakis, Nikolaos; Gikas, Evagelos; Halabalaki, Maria; Skaltsounis, Alexios-Leandros

2013-01-01

Oleuropein (OE) is a secoiridoid glycoside, which occurs mostly in the Oleaceae family presenting several pharmacological properties, including antioxidant, cardio-protective, anti-atherogenic effects etc. Based on these findings OE is commercially available, as Herbal Medicinal Product (HMP), claimed for its antioxidant effects. As there are general provisions of the medicine regulating bodies e.g. European Medicines Agency, the quality of the HMP’s must always be demonstrated. Therefore, a novel LC-MS methodology was developed and validated for the simultaneous quantification of OE and its main degradation product, hydroxytyrosol (HT), for the relevant OE claimed HMP’s. The internal standard (IS) methodology was employed and separation of OE, HT and IS was achieved on a C18 Fused Core column with 3.1 min overall run time employing the SIM method for the analytical signal acquisition. The method was validated according to the International Conference on Harmonisation requirements and the results show adequate linearity (r2 > 0.99) over a wide concentration range [0.1–15 μg/mL (n=12)] and a LLOQ value of 0.1 μg/mL, for both OE and HT. Furthermore, as it would be beneficial to control the quality taking into account all the substances of the OE claimed HMP’s; a metabolomics-like approach has been developed and applied for the total quality control of the different preparations employing UHPLC-HRMS-multivariate analysis (MVA). Four OE-claimed commercial HMP’s have been randomly selected and MVA similarity-based measurements were performed. The results showed that the examined samples could also be differentiated as evidenced according to their scores plot. Batch to batch reproducibility between the samples of the same brand has also been determined and found to be acceptable. Overall, the developed combined methodology has been found to be an efficient tool for the monitoring of the HMP’s total quality. Only one OE HMP has been found to be consistent to its label claim. PMID:24205178

48 CFR 846.470 - Use of commercial organizations for inspections and grading services.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Use of commercial organizations for inspections and grading services. 846.470 Section 846.470 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality...

Demonstrating PQS Effectiveness and Driving Continual Improvement: Evidence-Based Risk Reduction.

PubMed

Ramnarine, Emma; O'Donnell, Kevin

2018-04-18

Product knowledge grows and evolves during the life of a product. In order to maintain a state of control and deliver product with consistent quality throughout its commercial life, continuous improvement and product lifecycle management become essential. The practical link between product and process knowledge, risk-based control strategies, and continual improvement and innovation can be made stronger through evidence-based risk reduction. Regulatory relief and flexibility in post approval change management and overall product lifecycle management will only be possible with effective application of science and risk-based concepts and demonstrated effectiveness of the PQS in assuring a state of control. Copyright © 2018, Parenteral Drug Association.

Assessing image quality of low-cost laparoscopic box trainers: options for residents training at home.

PubMed

Kiely, Daniel J; Stephanson, Kirk; Ross, Sue

2011-10-01

Low-cost laparoscopic box trainers built using home computers and webcams may provide residents with a useful tool for practice at home. This study set out to evaluate the image quality of low-cost laparoscopic box trainers compared with a commercially available model. Five low-cost laparoscopic box trainers including the components listed were compared in random order to one commercially available box trainer: A (high-definition USB 2.0 webcam, PC laptop), B (Firewire webcam, Mac laptop), C (high-definition USB 2.0 webcam, Mac laptop), D (standard USB webcam, PC desktop), E (Firewire webcam, PC desktop), and F (the TRLCD03 3-DMEd Standard Minimally Invasive Training System). Participants observed still image quality and performed a peg transfer task using each box trainer. Participants rated still image quality, image quality with motion, and whether the box trainer had sufficient image quality to be useful for training. Sixteen residents in obstetrics and gynecology took part in the study. The box trainers showing no statistically significant difference from the commercially available model were A, B, C, D, and E for still image quality; A for image quality with motion; and A and B for usefulness of the simulator based on image quality. The cost of the box trainers A-E is approximately $100 to $160 each, not including a computer or laparoscopic instruments. Laparoscopic box trainers built from a high-definition USB 2.0 webcam with a PC (box trainer A) or from a Firewire webcam with a Mac (box trainer B) provide image quality comparable with a commercial standard.

Comparative effect of technical and commercial formulations of methamidophos on sperm quality and DNA integrity in mice.

PubMed

Urióstegui-Acosta, Mayrut; Hernández-Ochoa, Isabel; Solís-Heredia, María de Jesús; Martínez-Aguilar, Gerardo; Quintanilla-Vega, Betzabet

2014-08-01

Methamidophos (MET), widely used in developing countries, is a highly neurotoxic organophosphate pesticide that has been associated with male reproductive alterations. Commercial formulations of pesticides used by agricultural workers and urban sprayers are responsible for thousands of intoxications in developing countries and may not have the same effects as active pure ingredients. Therefore, we compared effects of MET technical (METt) and commercial (METc) grades on sperm quality and DNA integrity. Male mice were injected (intraperitoneal, i.p.) with METt or METc (3.75, 5, and 7 mg/kg bw/day/4 days) and sacrificed 24 h post-treatment. Sperm cells collected from epididymis-vas deferens were evaluated for quality parameters, DNA damage by the comet assay, and lipoperoxidation by malondialdehyde (MDA) production. Erythrocyte acetylcholinesterase (AChE) activity was evaluated by acetylthiocholine inhibition as an index of overall toxicity. A dose-dependent AChE inhibition was observed with both formulations. Sperm quality was decreased after treatment with both MET compounds, but the commercial formulation showed stronger effects; a similar profile was observed with the DNA damage, being METc more genotoxic. None MET formulation increased MDA, suggesting no peroxidative damage involved. In summary, the commercial formulation of MET was more reprotoxic and genotoxic than the active pure ingredient, highlighting that commercial formulations must be considered for more appropriate risk assessment of pesticide exposures. Copyright © 2012 Wiley Periodicals, Inc., a Wiley company.

Genetic divergence for high-molecular weight glutenin subunits (HMW-GS) in indigenous landraces and commercial cultivars of bread wheat of Pakistan.

PubMed

Yasmeen, F; Khurshid, H; Ghafoor, A

2015-05-11

Wheat flour quality is an important consideration in the breeding and development of new cultivars. A strong association between high-molecular weight glutenin subunits (HMW-GS) and bread making quality has resulted in the widespread utilization of HMW-GS in wheat breeding. In this study, we analyzed 242 lines of wheat, including landraces from the provinces of Punjab and Baluchistan, as well as the commercial varieties of Pakistan, to determine allelic variation in the Glu-A1, Glu-B1, and Glu-D1 loci encoding HMW-GS. Higher genetic diversity was observed for HMW-GS in landraces from Baluchistan, followed by landraces collected from Punjab and then commercial varieties. Rare and uncommon subunits were observed in Glu-B1, whereas Glu-A1 was less polymorphic. However, Glu-B1 was the highest contributor to overall diversity (78%), with a total of 31 rare alleles, followed by Glu-D1 (20%) with the high quality 5+10 allele and other variants. Commercial cultivars possessed favorable alleles, potentially from indirect selection for wheat flour quality by the breeders; however, this indirect selection has decreased the pedigree base of commercial cultivars. The allelic combinations, including 2*, 5+10, and 17+18, showing high quality scores were frequent among landraces, indicating their usefulness in future crop improvement and breeding programs.

Comparison of defined culture systems for feeder cell free propagation of human embryonic stem cells

PubMed Central

Akopian, Veronika; Beil, Stephen; Benvenisty, Nissim; Brehm, Jennifer; Christie, Megan; Ford, Angela; Fox, Victoria; Gokhale, Paul J.; Healy, Lyn; Holm, Frida; Hovatta, Outi; Knowles, Barbara B.; Ludwig, Tenneille E.; McKay, Ronald D. G.; Miyazaki, Takamichi; Nakatsuji, Norio; Oh, Steve K. W.; Pera, Martin F.; Rossant, Janet; Stacey, Glyn N.; Suemori, Hirofumi

2010-01-01

There are many reports of defined culture systems for the propagation of human embryonic stem cells in the absence of feeder cell support, but no previous study has undertaken a multi-laboratory comparison of these diverse methodologies. In this study, five separate laboratories, each with experience in human embryonic stem cell culture, used a panel of ten embryonic stem cell lines (including WA09 as an index cell line common to all laboratories) to assess eight cell culture methods, with propagation in the presence of Knockout Serum Replacer, FGF-2, and mouse embryonic fibroblast feeder cell layers serving as a positive control. The cultures were assessed for up to ten passages for attachment, death, and differentiated morphology by phase contrast microscopy, for growth by serial cell counts, and for maintenance of stem cell surface marker expression by flow cytometry. Of the eight culture systems, only the control and those based on two commercial media, mTeSR1 and STEMPRO, supported maintenance of most cell lines for ten passages. Cultures grown in the remaining media failed before this point due to lack of attachment, cell death, or overt cell differentiation. Possible explanations for relative success of the commercial formulations in this study, and the lack of success with other formulations from academic groups compared to previously published results, include: the complex combination of growth factors present in the commercial preparations; improved development, manufacture, and quality control in the commercial products; differences in epigenetic adaptation to culture in vitro between different ES cell lines grown in different laboratories. PMID:20186512

Seasonal Variation in Drinking and Domestic Water Sources and Quality in Port Harcourt, Nigeria

PubMed Central

Kumpel, Emily; Cock-Esteb, Alicea; Duret, Michel; de Waal, Dominick; Khush, Ranjiv

2017-01-01

We compared dry and rainy season water sources and their quality in the urban region of Port Harcourt, Nigeria. Representative sampling indicated that municipal water supplies represent < 1% of the water sources. Residents rely on privately constructed and maintained boreholes that are supplemented by commercially packaged bottled and sachet drinking water. Contamination by thermotolerant coliforms increased from 21% of drinking water sources in the dry season to 42% of drinking water sources in the rainy season (N = 356 and N = 397). The most significant increase was in sachet water, which showed the lowest frequencies of contamination in the dry season compared with other sources (15%, N = 186) but the highest frequencies during the rainy season (59%, N = 76). Only half as many respondents reported drinking sachet water in the rainy season as in the dry season. Respondents primarily used flush or pour-flush toilets connected to septic tanks (85%, N = 399). The remainder relied on pit latrines and hanging (pier) latrines that drained into surface waters. We found significant associations between fecal contamination in boreholes and the nearby presence of hanging latrines. Sanitary surveys of boreholes showed that more than half were well-constructed, and we did not identify associations between structural or site deficiencies and microbial water quality. The deterioration of drinking water quality during the rainy season is a serious public health risk for both untreated groundwater and commercially packaged water, highlighting a need to address gaps in monitoring and quality control. PMID:27821689

[Research on stormwater runoff quality of mountain city by source area monitoring].

PubMed

Li, Li-Qing; Shan, Bao-Qing; Zhao, Jian-Wei; Guo, Shu-Gang; Gao, Yong

2012-10-01

Stormwater runoff samples were collected from 10 source areas in Mountain City, Chongqing, during five rain events in an attempt to investigate the characteristics of runoff quality and influencing factors. The outcomes are expected to offer practical guidance of sources control of urban runoff pollution. The results indicated that the stormwater runoff of Mountain City presented a strong first flush for almost all events and constituents. The runoff quality indices were also influenced by the rainfall intensity. The concentration of TSS, COD, TN and TP decreased as the rainfall intensity increased. The concentrations of COD and TP in stormwater runoff were highly correlated with TSS concentrations. Suspended solid matter were not only the main pollutant of stormwater runoff but also served as the vehicle for transport of organic matter and phosphorus. Organic matter and phosphorus in stormwatrer runoff were mainly bound to particles, whereas nitrogen was predominantly dissolved, with ammonia and nitrate. A significant difference of stormwater runoff quality was observed among the ten monitored source areas. The highest magnitude of urban stormwater runoff pollution was expected in the commercial area and the first trunk road, followed by the minor road, residential area, parking lot and roof. Urban surface function, traffic volume, population density, and street sweeping practice are the main factors determining spatial differentiation of urban surface runoff quality. Commercial area, the first trunk road and residential area with high population density are the critical sources areas of urban stormwater runoff pollution.

Environmental Assessment for Toxecon Retrofit for Mercury and Multi-Pollutant Control, Presque Isle Power Plant, Marquette, Michigan

DOE Office of Scientific and Technical Information (OSTI.GOV)

N /A

This Environmental Assessment (EA) evaluates environmental issues associated with constructing and operating an integrated emissions control system proposed by We Energies and its project partners with cost-shared funding support by DOE. The proposed project would be demonstrated at the existing 90-MW Units 7, 8, and 9 of We Energies' coal-fired Presque Isle Power Plant in Marquette, Michigan. The commercial-scale demonstrate would allow utilities to make decisions regarding the integrated emissions control system as a viable commercial option. DOE's share of the funding for the 5-year demonstration project would be about $25 million, while $25 million would also be provided bymore » We Energies and its project partners. This project was selected by DOE under the Clean Coal Power Initiative (CCPI) for negotiation of a cooperative agreement to demonstrate the integration of technologies to reduce emissions of mercury (Hg) and particulate matter, as well as potentially control sulfur dioxide (SO{sub 2}), oxides of nitrogen (NO{sub x}) and hydrochloric acid (HCl) emissions. DOE's decision is whether or not to fund the project. The EA evaluates the principal environmental issues, including air quality, waste management, and traffic, that could result from construction and operation of the proposed project. The EA also considers two reasonably foreseeable scenarios that could result from the no-action alternative in which DOE would not provide cost-shared funding for the proposed project. Key findings include that potential air quality impacts resulting from the proposed project would generally be beneficial because plantwide air emissions would decrease or continue at the same level. The decrease in stack exit temperature would decrease the plume rise, which could result in increased downwind ground-level concentrations of those air pollutants experience little or no decrease in stack emissions. However, results of air dispersion modeling indicated that no major impacts would be expected relative to Prevention of Significant Deterioration increments and National Ambient Air Quality Standards.« less

Modeling in the quality by design environment: Regulatory requirements and recommendations for design space and control strategy appointment.

PubMed

Djuris, Jelena; Djuric, Zorica

2017-11-30

Mathematical models can be used as an integral part of the quality by design (QbD) concept throughout the product lifecycle for variety of purposes, including appointment of the design space and control strategy, continual improvement and risk assessment. Examples of different mathematical modeling techniques (mechanistic, empirical and hybrid) in the pharmaceutical development and process monitoring or control are provided in the presented review. In the QbD context, mathematical models are predominantly used to support design space and/or control strategies. Considering their impact to the final product quality, models can be divided into the following categories: high, medium and low impact models. Although there are regulatory guidelines on the topic of modeling applications, review of QbD-based submission containing modeling elements revealed concerns regarding the scale-dependency of design spaces and verification of models predictions at commercial scale of manufacturing, especially regarding real-time release (RTR) models. Authors provide critical overview on the good modeling practices and introduce concepts of multiple-unit, adaptive and dynamic design space, multivariate specifications and methods for process uncertainty analysis. RTR specification with mathematical model and different approaches to multivariate statistical process control supporting process analytical technologies are also presented. Copyright © 2017 Elsevier B.V. All rights reserved.

From producer to consumer: greenhouse tomato quality as affected by variety, maturity stage at harvest, transport conditions, and supermarket storage.

PubMed

Verheul, Michèl J; Slimestad, Rune; Tjøstheim, Irene Holta

2015-05-27

Possible causes for differences in quality traits at the time of buying were studied in two widely different red tomato types. Three maturity stages were harvested from commercial greenhouses and transferred immediately to controlled environments simulating different storage, transport, and supermarket conditions. Results show significant differences in development of color, fruit firmness, contents of soluble solids (SSC), titratable acids (TTA), phenolics, and carotenoids from harvest to sale, as related to postharvest conditions. Fruit firmness, SSC, and TTA of vine-ripened red cherry tomatoes was 30, 55 and 11% higher than for those harvested at breakers and ripened to red. Temperature, light, UVC radiation, or ethylene during 4 days transport affected tomato quality traits, and differences persisted during 3 weeks of supermarket storage. Ethylene exposure gave a 3.7-fold increase in lycopene content in cherry tomatoes, whereas UVC hormesis revealed a 6-fold increase compared with the control. Results can be used to update recommendations concerning optimal handling.

Particle counter as a tool to control pre-hydrolyzed coagulant dosing and rapid filtration efficiency in a conventional treatment system.

PubMed

Gumińska, Jolanta; Kłos, Marcin

2015-01-01

Filtration efficiency in a conventional water treatment system was analyzed in the context of pre-hydrolyzed coagulant overdosing. Two commercial coagulants of different aluminum speciation were tested. A study was carried out at a water treatment plant supplied with raw water of variable quality. The lack of stability of water quality caused many problems with maintaining the optimal coagulant dose. The achieved results show that the type of coagulant had a very strong influence on the effectiveness of filtration resulting from the application of an improper coagulant dose. The overdosing of high basicity coagulant (PAC85) caused a significant increase of fine particles in the outflow from the sedimentation tanks, which could not be retained in the filter bed due to high surface charge and the small size of hydrolysis products. When using a coagulant of lower basicity (PAC70), it was much easier to control the dose of coagulant and to adjust it to the changing water quality.

Pterodon pubescens oil: characterisation, certification of origin and quality control via mass spectrometry fingerprinting analysis.

PubMed

Cabral, E C; Sevart, L; Spindola, H M; Coelho, M B; Sousa, I M O; Queiroz, N C A; Foglio, M A; Eberlin, M N; Riveros, J M

2013-02-01

The oil obtained from Pterodon pubescens (Leguminosae) seeds are known to display anti-cancer, anti-dermatogenic and anti-nociceptive activitiy. Phytochemical studies have demonstrated that its main constituents are diterpenoids with voucapan skeletons. Considering the potential biological activities of the oil, rapid and efficient methods for assessing its quality would facilitate certification and quality control. To develop a direct mass spectrometric fingerprinting method for the P. pubescens seed oil that would focus on the major diterpenoids constituents, enabling quality control, origin certification and recognition of marker species in commercially available products. Two techniques were used: (i) direct infusion electrospray ionisation (ESI) mass spectrometry after solvent extraction and dilution and (ii) ambient desorption/ionisation via easy ambient sonic-spray ionisation, EASI(+)-MS, performed directly on the seed surface or at a paper surface imprinted with the oil. From a combination of ESI-MS, HRESI-MS and ESI-MS/MS data, 12 diterpenes were characterised, and typical profiles were obtained for the oil extract or the crude oil via both ESI-MS and EASI-MS. These techniques require no or very simple sample preparation protocols and the whole analytical processes with spectra acquisition take just a few minutes. Both techniques, but particularly EASI-MS, provide simple, fast and efficient MS fingerprinting methodologies to characterise the P. pubescens oil with typical (di)terpene profiles being applicable to quality control and certification of authenticity and origin. Copyright © 2012 John Wiley & Sons, Ltd.

48 CFR 46.203 - Criteria for use of contract quality requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Criteria for use of contract quality requirements. 46.203 Section 46.203 Federal Acquisition Regulations System FEDERAL...) Commercial (described in commercial catalogs, drawings, or industrial standards; see part 2); or (2) Military...

48 CFR 46.203 - Criteria for use of contract quality requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Criteria for use of contract quality requirements. 46.203 Section 46.203 Federal Acquisition Regulations System FEDERAL...) Commercial (described in commercial catalogs, drawings, or industrial standards; see part 2); or (2) Military...

48 CFR 46.203 - Criteria for use of contract quality requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Criteria for use of contract quality requirements. 46.203 Section 46.203 Federal Acquisition Regulations System FEDERAL...) Commercial (described in commercial catalogs, drawings, or industrial standards; see part 2); or (2) Military...

48 CFR 46.203 - Criteria for use of contract quality requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Criteria for use of contract quality requirements. 46.203 Section 46.203 Federal Acquisition Regulations System FEDERAL...) Commercial (described in commercial catalogs, drawings, or industrial standards; see part 2); or (2) Military...

48 CFR 46.203 - Criteria for use of contract quality requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Criteria for use of contract quality requirements. 46.203 Section 46.203 Federal Acquisition Regulations System FEDERAL...) Commercial (described in commercial catalogs, drawings, or industrial standards; see part 2); or (2) Military...

Human-centered sensor-based Bayesian control: Increased energy efficiency and user satisfaction in commercial lighting

NASA Astrophysics Data System (ADS)

Granderson, Jessica Ann

2007-12-01

The need for sustainable, efficient energy systems is the motivation that drove this research, which targeted the design of an intelligent commercial lighting system. Lighting in commercial buildings consumes approximately 13% of all the electricity generated in the US. Advanced lighting controls1 intended for use in commercial office spaces have proven to save up to 45% in electricity consumption. However, they currently comprise only a fraction of the market share, resulting in a missed opportunity to conserve energy. The research goals driving this dissertation relate directly to barriers hindering widespread adoption---increase user satisfaction, and provide increased energy savings through more sophisticated control. To satisfy these goals an influence diagram was developed to perform daylighting actuation. This algorithm was designed to balance the potentially conflicting lighting preferences of building occupants, with the efficiency desires of building facilities management. A supervisory control policy was designed to implement load shedding under a demand response tariff. Such tariffs offer incentives for customers to reduce their consumption during periods of peak demand, trough price reductions. In developing the value function occupant user testing was conducted to determine that computer and paper tasks require different illuminance levels, and that user preferences are sufficiently consistent to attain statistical significance. Approximately ten facilities managers were also interviewed and surveyed to isolate their lighting preferences with respect to measures of lighting quality and energy savings. Results from both simulation and physical implementation and user testing indicate that the intelligent controller can increase occupant satisfaction, efficiency, cost savings, and management satisfaction, with respect to existing commercial daylighting systems. Several important contributions were realized by satisfying the research goals. A general model of a daylighted environment was designed, and a practical means of user preference identification was defined. Further, a set of general procedures were identified for the design of human-centered sensor-based decision-analytic systems, and for the identification of the allowable uncertainty in nodes of interest. To confirm generality, a vehicle health monitoring problem was defined and solved using these two procedures. 1'Daylighting' systems use sensors to determine room occupancy and available sunlight, and automatically dim the lights in response.

Short Communication - Study on quality and efficacy of commercial tylosin and doxycycline products against local isolates of mycoplasma in broilers.

PubMed

Riazuddin, -; Khan, Sarzamin; Imtiaz, Naila; Aslam, Saima; Ahmad, Shakoor; Khan, Hamayun; Rabbani, Masood; Muhammad, Javed; Tanveer, Zafar Iqbal; Ali, Sakhawat

2017-03-01

The present study was conducted to investigate the quality and efficacy of commercially available preparations of tylosin and doxycycline available in the local market at Peshawar for poultry. In vitro and in vivo, tests were conducted to check the quality of these antimicrobial drugs. In vitro quality control test was performed by High performance liquid chromatographic (HPLC) and micro dilution method. In vivo, efficacy of the test drugs was checked in broilers infected with Mycoplasma gallisepticum. Results of HPLC indicated that test drug-2 contains doxycycline hydrochloride within specified limits but contain high quantity of active ingredient (Tylosin tartrate 120%). Recovery percentage of test drugs (3, 4, 5) were below the pharmacopoeial limit, which contained low quantity of tylosin tartrate (85%, 87.5%, 85%) respectively however, percent recovery of doxycycline were in the appropriate limits. All the tested drugs were effective against Mycoplasma gallisepticum and showed minimum inhibitory concentration (MIC) at 1.9μg/ml. The in vivo result indicated that all tested drugs decreased morbidity and mortality in infected chicks. The birds treated with test drugs (3 and 5) showed mortality of 9.5%, which was slightly higher than the other test groups. The current study suggested that there are incidences of substandard drugs in Pakistan and the drug regularity authorities should take strict actions against the manufacturing companies.

Meat Quality Assessment by Electronic Nose (Machine Olfaction Technology)

PubMed Central

Ghasemi-Varnamkhasti, Mahdi; Mohtasebi, Seyed Saeid; Siadat, Maryam; Balasubramanian, Sundar

2009-01-01

Over the last twenty years, newly developed chemical sensor systems (so called “electronic noses”) have made odor analyses possible. These systems involve various types of electronic chemical gas sensors with partial specificity, as well as suitable statistical methods enabling the recognition of complex odors. As commercial instruments have become available, a substantial increase in research into the application of electronic noses in the evaluation of volatile compounds in food, cosmetic and other items of everyday life is observed. At present, the commercial gas sensor technologies comprise metal oxide semiconductors, metal oxide semiconductor field effect transistors, organic conducting polymers, and piezoelectric crystal sensors. Further sensors based on fibreoptic, electrochemical and bi-metal principles are still in the developmental stage. Statistical analysis techniques range from simple graphical evaluation to multivariate analysis such as artificial neural network and radial basis function. The introduction of electronic noses into the area of food is envisaged for quality control, process monitoring, freshness evaluation, shelf-life investigation and authenticity assessment. Considerable work has already been carried out on meat, grains, coffee, mushrooms, cheese, sugar, fish, beer and other beverages, as well as on the odor quality evaluation of food packaging material. This paper describes the applications of these systems for meat quality assessment, where fast detection methods are essential for appropriate product management. The results suggest the possibility of using this new technology in meat handling. PMID:22454572

Development, characterization and qualification of first GEM foils produced in India

NASA Astrophysics Data System (ADS)

Shah, Aashaq; Ahmed, Asar; Gola, Mohit; Sharma, Ram Krishna; Malhotra, Shivali; Kumar, Ashok; Naimuddin, Md.; Menon, Pradeep; Srinivasan, K.

2018-06-01

The increasing demand for Gas Electron Multiplier (GEM) foils has been driven by their application in many current and proposed high-energy physics experiments. Micropack, a Bengaluru-based company, has established and commercialized GEM foils for the first time in India. Micropack used the double-mask etching technique to successfully produce 10 cm × 10 cm GEM foil. In this paper, we report on the development as well as the geometrical and electrical properties of these foils, including the size uniformity of the holes and leakage current measurements. Our characterization studies show that the foils are of good quality and satisfy all the necessary quality control criteria.

[Implementation of a web based software for documentation and control of quality of an acute pain service].

PubMed

Pawlik, Michael T; Abel, Reinhard; Abt, Gregor; Kieninger, Martin; Graf, Bernhard Martin; Taeger, Kai; Ittner, Karl Peter

2009-07-01

Providing an acute pain service means accumulation of a large amount of data. The alleviation of data collection, improvement of data quality and data analysis plays a pivotal role. The electronic medical record (EMR) is gaining more and more importance in this context and is continuously spreading in clinical practice. Up to now only a few commercial softwares are available that specifically fit to the needs of an acute pain service. Here we report the development and implementation of such a program (Schmerzvisite, Medlinq, Hamburg, Germany) in the acute pain service of a University Hospital.

Uterine fluid proteins and egg quality characteristics for 2 commercial and 2 heritage laying hen lines in response to manipulation of dietary calcium and vitamin D3.

PubMed

Kaur, Ravinder; Rathgeber, Bruce M; Thompson, Kristen L; Macisaac, Janice

2013-09-01

The aim of this study was to evaluate the quality of eggs from 2 selected commercial strains of laying hens and 2 unselected lines of chickens fed diets with different combinations of Ca and vitamin D and relate it to the profile of uterine proteins and ultrastructure of the shell. A group of 4 chickens was housed in each of 24 cages. The group consisted of one representative from each of the following breeds: Lohmann LSL- Lite, Lohmann Classic-Brown, Fayoumi, and Light Sussex. Six dietary combinations of Ca and vitamin D(3) (3.35%, 2,500 IU; 4.10%, 2,500 IU (control); 4.85%, 2,500 IU; 3.35%, 200 IU; 4.10%, 200 IU; and 4.85%, 200 IU) were randomly assigned to 4 replicate cages for 2 treatment periods (26-29 and 56-59 wk of age). Data were analyzed as a split-plot design with cage as the main plot and hen as the subplot. Egg quality traits were different (P < 0.0001) between commercial and heritage breeds. Lohmann Brown had stronger shells with higher specific gravity compared with other breeds. Both commercial and heritage birds responded to a drop in vitamin D3 level by marked reduction in shell thickness. The SDS-PAGE profiles of uterine fluid samples revealed a decrease (P < 0.05) in 200-, 150-, 116-, and ≤6.5-kDa proteins, whereas proteins with molecular weight (MW) of 80, 55, 52, 45, 42, and 28 kDa increased with bird age. A 36- and 52-kDa protein band was most intense for Fayoumi compared with other breeds. Ultrastructural characteristics showed flattened and deeply etched mammillary caps for Lohmann Brown and the presence of type A and type B bodies between mammillary cones in eggshells from Fayoumi and Lohmann Lite. The negative correlation between ultrastructural characteristics, which decrease with bird age, and the 116-kDa uterine protein band could provide insight into reduced eggshell quality as hens age.

Dynamics and controls in maglev systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Chen, S.S.; Rote, D.M.

1992-09-01

The dynamic response of magnetically levitated (maglev) ground transportation systems has important consequences for safety and ride quality, guideway design, and system costs. Ride quality is determined by vehicle response and by environmental factors such as humidity and noise. The dynamic response of the vehicles is the key element in determining ride quality, and vehicle stability is an important safety-related element. To design a proper guideway that provides acceptable ride quality in the stable region, vehicle dynamics must be understood. Furthermore the trade-off between guideway smoothness and the levitation and control systems must be considered if maglev systems are tomore » be economically feasible. The link between the guideway and the other maglev components is vehicle dynamics. For a commercial maglev system, vehicle dynamics must be analyzed and tested in detail. In this study, the role of dynamics and controls in maglev vehicle/guideway interactions is discussed, and the literature on modeling the dynamic interactions of vehicle/guideway and suspension controls for ground vehicles is reviewed. Particular emphasis is placed on modeling vehicle/guideway interactions and response characteristics of maglev systems for a multicar, multiload vehicle traveling on a single- or doublespan flexible guideway, including coupling effects of vehicle/guideway, comparison of concentrated and distributed loads, and ride comfort. Different control-law designs are introduced into vehicle suspensions when a simple two-degree-of-freedom vehicle model is applied. Active and semiactive control designs for primary and secondary suspensions do improve the response of vehicle and provide acceptable ride comfort. Finally, future research associated with dynamics and controls of vehicle/guideway systems is identified.« less

Preparation and Quality Control of 68Ga-Citrate for PET Applications

PubMed Central

Aghanejad, Ayuob; Jalilian, Amir Reza; Ardaneh, Khosro; Bolourinovin, Fatemeh; Yousefnia, Hassan; Samani, Ali Bahrami

2015-01-01

Objective(s): In nuclear medicine studies, gallium-68 (8Ga) citrate has been recently known as a suitable infection agent in positron emission tomography (PET). In this study, by applying an in-house produced 68Ge/68Ga generator, a simple technique for the synthesis and quality control of 68Ga-citrate was introduced; followed by preliminary animal studies. Methods: 68GaCl3 eluted from the generator was studied in terms of quality control factors including radiochemical purity (assessed by HPLC and RTLC), chemical purity (assessed by ICP-EOS), radionuclide purity (evaluated by HPGe), and breakthrough. 68Ga-citrate was prepared from eluted 68GaCl3 and sodium citrate under various reaction conditions. Stability of the complex was evaluated in human serum for 2 h at 370C, followed by biodistribution studies in rats for 120 min. Results: 68Ga-citrate was prepared with acceptable radiochemical purity (>97 ITLC and >98% HPLC), specific activity (4-6 GBq/mM), chemical purity (Sn, Fe<0.3 ppm and Zn<0.2 ppm) within 15 min at 500C. The biodistribution of 68Ga-citrate was consistent with former reports up to 120 minutes. Conclusion: This study demonstrated the possible in-house preparation and quality control of 68Ga-citrate, using a commercially available 68Ge/68Ga generator for PET imaging throughout the country. PMID:27408889

Prevalence of IgE reactivities in mold-allergic subjects to commercially available fungal enzymes.

PubMed

Horner, W Elliott; Armstrong, Maricelis; El-Dahr, Jane; McCants, Marjorie; Reese, Gerald; Kobernick, Aaron K; Lehrer, Samuel B

2008-01-01

Fungi are important aeroallergens. However, fungal allergen sources of consistent quality for clinical testing are not readily available. Because some allergens have been identified as enzymes, we assessed the prevalence of IgE reactivity to commercially available fungal enzymes. The purpose of this study was to determine IgE antibody reactivity by radioallergosorbent assay (RAST) to commercially available fungal enzymes in mold-allergic individuals. Sera from 20 subjects with symptoms of respiratory allergies and skin test reactivity to 2 or more fungal allergens (4 conidial [imperfecti] fungi and/or 8 basidiomycetes) were selected. Controls were six atopic individuals with neither history of fungal allergy nor skin test reactivity to fungi. Seventeen commercial fungal enzymes were used as antigens to evaluate the subjects' IgE antibody reactivity by RAST. Sera from most fungus-allergic individuals showed substantial IgE antibody reactivity to enzymes; control sera showed little or no reactivity. The mean reactivity to all commercial enzymes of all subjects tested was RAST > or = 3% with only one exception. The most reactive fungal enzymes were invertase (bakers' yeast, Saccharomyces cerevisiae), cellulase (Trichoderma viride), and glucosidase (brewers yeast, S. cerevisiae) with mean binding of 14.6, 9.5, and 8.8%, respectively. Using RAST results with a combination of four enzymes from S. cerevisiae (brewers yeast glucosidase, bakers' yeast maltase, invertase, and invertase V), a sensitivity of 100% was shown for detecting mold-allergic patients. The studies suggest that fungal enzymes may be useful source materials for the identification of fungal allergens and may also provide readily available source materials to produce improved diagnostic and therapeutic reagents.

JACIE: A Model Partnership

NASA Technical Reports Server (NTRS)

Thome, Kurt; Goldberg, Mitch; Mita, Dath; Stensaas, Gregory L.

2013-01-01

The National Aeronautics and Space Administration (NASA), National Oceanic and Atmospheric Administration (NOAA), the United States Department of Agriculture (USDA), and the United States Geological Survey (USGS), and their associates and partners, are directly responsible for establishing and leading a unique interagency team of scientists and engineers who work together to evaluate and enhance the quality remote sensing data for commercial and government use. This team is called "the Joint Agency Commercial Imagery Evaluation (JACIE) team". The team works together to define, prioritize, assign, and assess civil and commercial image quality and jointly sponsors an annual JACIE Civil Commercial Imagery Evaluation workshop with participation support from the remote sensing calibration and validation science community.

ACOs Holding Commercial Contracts Are Larger And More Efficient Than Noncommercial ACOs.

PubMed

Peiris, David; Phipps-Taylor, Madeleine C; Stachowski, Courtney A; Kao, Lee-Sien; Shortell, Stephen M; Lewis, Valerie A; Rosenthal, Meredith B; Colla, Carrie H

2016-10-01

Accountable care organizations (ACOs) have diverse contracting arrangements and have displayed wide variation in their performance. Using data from national surveys of 399 ACOs, we examined differences between the 228 commercial ACOs (those with commercial payer contracts) and the 171 noncommercial ACOs (those with only public contracts, such as with Medicare or Medicaid). Commercial ACOs were significantly larger and more integrated with hospitals, and had lower benchmark expenditures and higher quality scores, compared to noncommercial ACOs. Among all of the ACOs, there was low uptake of quality and efficiency activities. However, commercial ACOs reported more use of disease monitoring tools, patient satisfaction data, and quality improvement methods than did noncommercial ACOs. Few ACOs reported having high-level performance monitoring capabilities. About two-thirds of the ACOs had established processes for distributing any savings accrued, and these ACOs allocated approximately the same amount of savings to the ACOs themselves, participating member organizations, and physicians. Our findings demonstrate that ACO delivery systems remain at a nascent stage. Structural differences between commercial and noncommercial ACOs are important factors to consider as public policy efforts continue to evolve. Project HOPE—The People-to-People Health Foundation, Inc.

An Optimal Current Controller Design for a Grid Connected Inverter to Improve Power Quality and Test Commercial PV Inverters.

PubMed

Algaddafi, Ali; Altuwayjiri, Saud A; Ahmed, Oday A; Daho, Ibrahim

2017-01-01

Grid connected inverters play a crucial role in generating energy to be fed to the grid. A filter is commonly used to suppress the switching frequency harmonics produced by the inverter, this being passive, and either an L- or LCL-filter. The latter is smaller in size compared to the L-filter. But choosing the optimal values of the LCL-filter is challenging due to resonance, which can affect stability. This paper presents a simple inverter controller design with an L-filter. The control topology is simple and applied easily using traditional control theory. Fast Fourier Transform analysis is used to compare different grid connected inverter control topologies. The modelled grid connected inverter with the proposed controller complies with the IEEE-1547 standard, and total harmonic distortion of the output current of the modelled inverter has been just 0.25% with an improved output waveform. Experimental work on a commercial PV inverter is then presented, including the effect of strong and weak grid connection. Inverter effects on the resistive load connected at the point of common coupling are presented. Results show that the voltage and current of resistive load, when the grid is interrupted, are increased, which may cause failure or damage for connecting appliances.

An Optimal Current Controller Design for a Grid Connected Inverter to Improve Power Quality and Test Commercial PV Inverters

PubMed Central

Altuwayjiri, Saud A.; Ahmed, Oday A.; Daho, Ibrahim

2017-01-01

Grid connected inverters play a crucial role in generating energy to be fed to the grid. A filter is commonly used to suppress the switching frequency harmonics produced by the inverter, this being passive, and either an L- or LCL-filter. The latter is smaller in size compared to the L-filter. But choosing the optimal values of the LCL-filter is challenging due to resonance, which can affect stability. This paper presents a simple inverter controller design with an L-filter. The control topology is simple and applied easily using traditional control theory. Fast Fourier Transform analysis is used to compare different grid connected inverter control topologies. The modelled grid connected inverter with the proposed controller complies with the IEEE-1547 standard, and total harmonic distortion of the output current of the modelled inverter has been just 0.25% with an improved output waveform. Experimental work on a commercial PV inverter is then presented, including the effect of strong and weak grid connection. Inverter effects on the resistive load connected at the point of common coupling are presented. Results show that the voltage and current of resistive load, when the grid is interrupted, are increased, which may cause failure or damage for connecting appliances. PMID:28540362

Metropolitan Boston air quality control region: transportation control plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1975-02-28

The EPA is considering a number of amendments to the transportation control plan which it promulgated Nov. 8, 1973 for the Metropolitan Boston Intrastate Air Quality Control Region. Included in the proposed amendments is a revised regulation for reduction of commuter travel which would include students and employees. This program would be implemented in conjunction with the carpool matching program being developed by the Commonwealth of Massachusetts and the employee pass program offered by the Massachusetts Bay Transportation Authority. A new provision for limiting overall hydrocarbon emissions from major users of organic compounds is included. Also published are a proposalmore » for encouraging bicycle use, new proposals for controlling carbon monoxide levels outside the Boston core area, and a new procedure for periodic monitoring and updating of the plan. Other features of the original plan are retained with modifications in areas including the ceiling on the level of commercial parking spaces in the so-called ''freeze'' area, limitations of on-street commuter parking, a semiannual inspection and maintenance program, a retrofit program, and incentives for carpool and transit use.« less

Quantitative Determination of Bioactive Constituents in Noni Juice by High-performance Liquid Chromatography with Electrospray Ionization Triple Quadrupole Mass Spectrometry.

PubMed

Yan, Yongqiu; Lu, Yu; Jiang, Shiping; Jiang, Yu; Tong, Yingpeng; Zuo, Limin; Yang, Jun; Gong, Feng; Zhang, Ling; Wang, Ping

2018-01-01

Noni juice has been extensively used as folk medicine for the treatment of arthritis, infections, analgesic, colds, cancers, and diabetes by Polynesians for many years. Due to the lack of standard scientific evaluation methods, various kinds of commercial Noni juice with different quality and price were available on the market. To establish a sensitive, reliable, and accurate high-performance liquid chromatography with electrospray ionization triple quadrupole mass spectrometry (HPLC-ESI-MS/MS) method for separation, identification, and simultaneous quantitative analysis of bioactive constituents in Noni juice. The analytes and eight batches of commercially available samples from different origins were separated and analyzed by the HPLC-ESI-MS/MS method on an Agilent ZORBAX SB-C 18 (150 mm × 4.6 mm i.d., 5 μm) column using a gradient elution of acetonitrile-methanol-0.05% glacial acetic acid in water (v/v) at a constant flow rate of 0.5 mL/min. Seven components were identification and all of the assay parameters were within the required limits. Components were within the correlation coefficient values ( R 2 ≥ 0.9993) at the concentration ranges tested. The precision of the assay method was <0.91% and the repeatability between 1.36% and 3.31%. The accuracy varied from 96.40% to 103.02% and the relative standard deviations of stability were <3.91%. Samples from the same origin showed similar content while different origins showed significant different result. The developed methods would provide a reliable basis and be useful in the establishment of a rational quality control standard of Noni juice. Separation, identification, and simultaneous quantitative analysis method of seven bioactive constituents in Noni juice is originally developed by high-performance liquid chromatography with electrospray ionization triple quadrupole mass spectrometryThe presented method was successfully applied to the quality control of eight batches of commercially available samples of Noni juiceThis method is simple, sensitive, reliable, accurate, and efficient method with strong specificity, good precision, and high recovery rate and provides a reliable basis for quality control of Noni juice. Abbreviations used: HPLC-ESI-MS/MS: High-performance liquid chromatography with electrospray ionization triple quadrupole mass spectrometry, LOD: Limit of detection, LOQ: Limit of quantitation, S/N: Signal-to-noise ratio, RSD: Relative standard deviations, DP: Declustering potential, CE: Collision energy, MRM: Multiple reaction monitoring, RT: Retention time.

Quantitative Determination of Bioactive Constituents in Noni Juice by High-performance Liquid Chromatography with Electrospray Ionization Triple Quadrupole Mass Spectrometry

PubMed Central

Yan, Yongqiu; Lu, Yu; Jiang, Shiping; Jiang, Yu; Tong, Yingpeng; Zuo, Limin; Yang, Jun; Gong, Feng; Zhang, Ling; Wang, Ping

2018-01-01

Background: Noni juice has been extensively used as folk medicine for the treatment of arthritis, infections, analgesic, colds, cancers, and diabetes by Polynesians for many years. Due to the lack of standard scientific evaluation methods, various kinds of commercial Noni juice with different quality and price were available on the market. Objective: To establish a sensitive, reliable, and accurate high-performance liquid chromatography with electrospray ionization triple quadrupole mass spectrometry (HPLC-ESI-MS/MS) method for separation, identification, and simultaneous quantitative analysis of bioactive constituents in Noni juice. Materials and Methods: The analytes and eight batches of commercially available samples from different origins were separated and analyzed by the HPLC-ESI-MS/MS method on an Agilent ZORBAX SB-C18 (150 mm × 4.6 mm i.d., 5 μm) column using a gradient elution of acetonitrile-methanol-0.05% glacial acetic acid in water (v/v) at a constant flow rate of 0.5 mL/min. Results: Seven components were identification and all of the assay parameters were within the required limits. Components were within the correlation coefficient values (R2 ≥ 0.9993) at the concentration ranges tested. The precision of the assay method was <0.91% and the repeatability between 1.36% and 3.31%. The accuracy varied from 96.40% to 103.02% and the relative standard deviations of stability were <3.91%. Samples from the same origin showed similar content while different origins showed significant different result. Conclusions: The developed methods would provide a reliable basis and be useful in the establishment of a rational quality control standard of Noni juice. SUMMARY Separation, identification, and simultaneous quantitative analysis method of seven bioactive constituents in Noni juice is originally developed by high-performance liquid chromatography with electrospray ionization triple quadrupole mass spectrometryThe presented method was successfully applied to the quality control of eight batches of commercially available samples of Noni juiceThis method is simple, sensitive, reliable, accurate, and efficient method with strong specificity, good precision, and high recovery rate and provides a reliable basis for quality control of Noni juice. Abbreviations used: HPLC-ESI-MS/MS: High-performance liquid chromatography with electrospray ionization triple quadrupole mass spectrometry, LOD: Limit of detection, LOQ: Limit of quantitation, S/N: Signal-to-noise ratio, RSD: Relative standard deviations, DP: Declustering potential, CE: Collision energy, MRM: Multiple reaction monitoring, RT: Retention time. PMID:29576704

Lactobacillus plantarum (KACC 92189) as a Potential Probiotic Starter Culture for Quality Improvement of Fermented Sausages

PubMed Central

2018-01-01

This study was conducted to evaluate the effects of fermenting temperature on the applicability of Lactobacillus plantarum for production of fermented sausages as starter cultures, and its applicable efficiency was also compared with those inoculated with commercial starter culture or non-inoculated control. The L. plantarum isolated from a naturally-fermented meat, identified by 16S rDNA sequencing and again identified by de novo Assembly Analysis method was used as a starter culture. Six treatments: 3 with L. plantarum at different fermenting temperatures (20, 25 and 30°C), and other 3 treatments (1 with commercial starter culture, 1 with its mixture with L. plantarum and 1 non-inoculated control) fermented under the same conditions (25°C) were prepared. Results revealed that the fermenting temperature considerably affected the pH change in samples added with L. plantarum; the highest pH drop rate (1.57 unit) was obtained on the samples fermented at 30°C, followed by those at 25°C (1.3 unit) and 20°C (0.99 unit) after 4 days fermentation. Increasing the temperature up to 30°C resulted in significantly lower spoilage bacteria count (5.15 log CFU/g) and lipid oxidation level in the products inoculated with L. plantarum. The sensory analysis also showed that the samples added with L. plantarum at 30°C had significantly higher odor, taste and acceptability scores than those fermented at lower temperatures. Under the same processing condition, although the L. plantarum showed slightly lower acidification than the commercial starter culture, however, it significantly improved the eating quality of the product. PMID:29725237

Cost-utility of cognitive behavioral therapy for low back pain from the commercial payer perspective.

PubMed

Norton, Giulia; McDonough, Christine M; Cabral, Howard; Shwartz, Michael; Burgess, James F

2015-05-15

Markov cost-utility model. To evaluate the cost-utility of cognitive behavioral therapy (CBT) for the treatment of persistent nonspecific low back pain (LBP) from the perspective of US commercial payers. CBT is widely deemed clinically effective for LBP treatment. The evidence is suggestive of cost-effectiveness. We constructed and validated a Markov intention-to-treat model to estimate the cost-utility of CBT, with 1-year and 10-year time horizons. We applied likelihood of improvement and utilities from a randomized controlled trial assessing CBT to treat LBP. The trial randomized subjects to treatment but subjects freely sought health care services. We derived the cost of equivalent rates and types of services from US commercial claims for LBP for a similar population. For the 10-year estimates, we derived recurrence rates from the literature. The base case included medical and pharmaceutical services and assumed gradual loss of skill in applying CBT techniques. Sensitivity analyses assessed the distribution of service utilization, utility values, and rate of LBP recurrence. We compared health plan designs. Results are based on 5000 iterations of each model and expressed as an incremental cost per quality-adjusted life-year. The incremental cost-utility of CBT was $7197 per quality-adjusted life-year in the first year and $5855 per quality-adjusted life-year over 10 years. The results are robust across numerous sensitivity analyses. No change of parameter estimate resulted in a difference of more than 7% from the base case for either time horizon. Including chiropractic and/or acupuncture care did not substantively affect cost-effectiveness. The model with medical but no pharmaceutical costs was more cost-effective ($5238 for 1 yr and $3849 for 10 yr). CBT is a cost-effective approach to manage chronic LBP among commercial health plans members. Cost-effectiveness is demonstrated for multiple plan designs. 2.

How Online Quality Ratings Influence Patients' Choice of Medical Providers: Controlled Experimental Survey Study.

PubMed

Yaraghi, Niam; Wang, Weiguang; Gao, Guodong Gordon; Agarwal, Ritu

2018-03-26

In recent years, the information environment for patients to learn about physician quality is being rapidly changed by Web-based ratings from both commercial and government efforts. However, little is known about how various types of Web-based ratings affect individuals' choice of physicians. The objective of this research was to measure the relative importance of Web-based quality ratings from governmental and commercial agencies on individuals' choice of primary care physicians. In a choice-based conjoint experiment conducted on a sample of 1000 Amazon Mechanical Turk users in October 2016, individuals were asked to choose their preferred primary care physician from pairs of physicians with different ratings in clinical and nonclinical aspects of care provided by governmental and commercial agencies. The relative log odds of choosing a physician increases by 1.31 (95% CI 1.26-1.37; P<.001) and 1.32 (95% CI 1.27-1.39; P<.001) units when the government clinical ratings and commercial nonclinical ratings move from 2 to 4 stars, respectively. The relative log odds of choosing a physician increases by 1.12 (95% CI 1.07-1.18; P<.001) units when the commercial clinical ratings move from 2 to 4 stars. The relative log odds of selecting a physician with 4 stars in nonclinical ratings provided by the government is 1.03 (95% CI 0.98-1.09; P<.001) units higher than a physician with 2 stars in this rating. The log odds of selecting a physician with 4 stars in nonclinical government ratings relative to a physician with 2 stars is 0.23 (95% CI 0.13-0.33; P<.001) units higher for females compared with males. Similar star increase in nonclinical commercial ratings increases the relative log odds of selecting the physician by female respondents by 0.15 (95% CI 0.04-0.26; P=.006) units. Individuals perceive nonclinical ratings provided by commercial websites as important as clinical ratings provided by government websites when choosing a primary care physician. There are significant gender differences in how the ratings are used. More research is needed on whether patients are making the best use of different types of ratings, as well as the optimal allocation of resources in improving physician ratings from the government's perspective. ©Niam Yaraghi, Weiguang Wang, Guodong (Gordon) Gao, Ritu Agarwal. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 26.03.2018.

How the quality and processing attributes of commercial sweet sorghum hybrids and cultivar compare for biorefining

USDA-ARS?s Scientific Manuscript database

Quality and processing attributes of sweet sorghum (Sorghum bicolor L. Moench) biomass are critical to the development of a large-scale industry for the manufacture of bioproducts. Two commercial sweet sorghum hybrids 105 and 106, later and earlier maturing, respectively, were compared to inbred, l...

Glass-to-Metal Seal Quality.

DTIC Science & Technology

1982-05-01

SELECTION AND EVALUATION . . . . . . . . . . . . . . 2 2.2 MICROELECTRONIC PACKAGES AND THEIR QUALITY . . . * . . . . . . . . 5 2.3 EQUIPMENT...liquid penetrant testing for various microelectronic package hermeticity. I t I MATERIALS AND EQUIPMENT 2.1 DYE PENETRANT SELECTION AND EVALUATION...a commercial visible dye penetrant and a commercial fluorescent dye penetrant were selected as being suitable for the testing of microelectronic

Effectiveness of commercial video gaming on fine motor control in chronic stroke within community-level rehabilitation.

PubMed

Paquin, Kate; Ali, Suzanne; Carr, Kelly; Crawley, Jamie; McGowan, Cheri; Horton, Sean

2015-01-01

The purpose of this study was to investigate the effectiveness of commercial gaming as an intervention for fine motor recovery in chronic stroke. Ten chronic phase post-stroke participants (mean time since CVA = 39 mos; mean age = 72 yrs) completed a 16-session program using the Nintendo Wii for 15 min two times per week with their more affected hand (10 right handed). Functional recovery (Jebsen Hand Function Test (JHFT), Box and Block Test (BBT), Nine Hole Peg Test (NHPT)), and quality of life (QOL; Stroke Impact Scale (SIS)) were measured at baseline (pre-testing), after 8 sessions (mid-testing) and after 16 sessions (post-testing). Significant improvements were found with the JHFT, BBT and NHPT from pre-testing to post-testing (p = 0.03, p = 0.03, p = 0.01, respectively). As well, there was an increase in perceived QOL from pre-testing to post-testing, as determined by the SIS (p = 0.009). Commercial gaming may be a viable resource for those with chronic stroke. Future research should examine the feasibility of this as a rehabilitation tool for this population. Stroke survivors often live with lasting effects from their injury, however, those with chronic stroke generally receive little to no rehabilitation due to a perceived motor recovery plateau. Virtual reality in the form of commercial gaming is a novel and motivating way for clients to complete rehabilitation. The Nintendo Wii may be a feasible device to improve both functional ability and perceived quality of life in chronic stroke survivors.

Characterization and manufacture of braided composites for large commercial aircraft structures

NASA Technical Reports Server (NTRS)

Fedro, Mark J.; Willden, Kurtis

1992-01-01

Braided composite materials, one of the advanced material forms which is under investigation in Boeing's ATCAS program, have been recognized as a potential cost-effective material form for fuselage structural elements. Consequently, there is a strong need for more knowledge in the design, manufacture, test, and analysis of textile structural composites. The overall objective of this work is to advance braided composite technology towards applications to a large commercial transport fuselage. This paper summarizes the mechanics of materials and manufacturing demonstration results which have been obtained in order to acquire an understanding of how braided composites can be applied to a commercial fuselage. Textile composites consisting of 1D, 2D triaxial, and 3D braid patterns with thermoplastic and two RTM resin systems were investigated. The structural performance of braided composites was evaluated through an extensive mechanical test program. Analytical methods were also developed and applied to predict the following: internal fiber architectures, stiffnesses, fiber stresses, failure mechanisms, notch effects, and the entire history of failure of the braided composites specimens. The applicability of braided composites to a commercial transport fuselage was further assessed through a manufacturing demonstration. Three foot fuselage circumferential hoop frames were manufactured to demonstrate the feasibility of consistently producing high quality braided/RTM composite primary structures. The manufacturing issues (tooling requirements, processing requirements, and process/quality control) addressed during the demonstration are summarized. The manufacturing demonstration in conjunction with the mechanical test results and developed analytical methods increased the confidence in the ATCAS approach to the design, manufacture, test, and analysis of braided composites.

Comparison of reduced sugar high quality chocolates sweetened with stevioside and crude stevia 'green' extract.

PubMed

Torri, Luisa; Frati, Alessandra; Ninfali, Paolino; Mantegna, Stefano; Cravotto, Giancarlo; Morini, Gabriella

2017-06-01

The demand for zero and reduced-sugar food products containing cocoa is expanding continuously. The present study was designed to evaluate the feasibility of producing high-quality chocolate sweetened with a crude extract of Stevia rebaudiana (Bertoni) prepared by a green microwave-assisted water-steam extraction procedure. Seven approximately isosweet chocolate formulations were developed, mixing cocoa paste, sucrose, commercial stevioside, crude green extract and maltitol in different proportions. All samples were analyzed for the determination of polyphenol and flavonoid content, antioxidant activity, and sensory acceptability. The use of a crude stevia extract allowed low-sugar, high-quality chocolates to be obtained that were also acceptable by consumers and had a significant increased antioxidant activity. Moreover, consumers' segmentation revealed a cluster of consumers showing the same overall liking for the sample with 50% sucrose replaced by the stevia crude extract as that obtained with the commercial stevioside and the control sample (without sucrose replacement). The results provide information that can contribute to promoting the development of sweet food products, with advantages in terms of an improved nutritional value (reduced sugar content and increased antioxidant activity) and a reduced impact of the production process on the environment. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Multivariate analysis in the pharmaceutical industry: enabling process understanding and improvement in the PAT and QbD era.

PubMed

Ferreira, Ana P; Tobyn, Mike

2015-01-01

In the pharmaceutical industry, chemometrics is rapidly establishing itself as a tool that can be used at every step of product development and beyond: from early development to commercialization. This set of multivariate analysis methods allows the extraction of information contained in large, complex data sets thus contributing to increase product and process understanding which is at the core of the Food and Drug Administration's Process Analytical Tools (PAT) Guidance for Industry and the International Conference on Harmonisation's Pharmaceutical Development guideline (Q8). This review is aimed at providing pharmaceutical industry professionals an introduction to multivariate analysis and how it is being adopted and implemented by companies in the transition from "quality-by-testing" to "quality-by-design". It starts with an introduction to multivariate analysis and the two methods most commonly used: principal component analysis and partial least squares regression, their advantages, common pitfalls and requirements for their effective use. That is followed with an overview of the diverse areas of application of multivariate analysis in the pharmaceutical industry: from the development of real-time analytical methods to definition of the design space and control strategy, from formulation optimization during development to the application of quality-by-design principles to improve manufacture of existing commercial products.

Visual quality evaluation of urban commercial streetscape for the development of landscape visual planning system in provincial street corridors in Malang, Indonesia

NASA Astrophysics Data System (ADS)

Santosa, H.; Ernawati, J.; Wulandari, L. D.

2018-03-01

The visual aesthetic experience in urban spaces is important in establishing a comfortable and satisfying experience for the community. The embodiment of a good visual image of urban space will encourage the emergence of positive perceptions and meanings stimulating the community to produce a good reaction to its urban space. Moreover, to establish a Good Governance in urban planning and design, it is necessary to boost and promote a community participation in the process of controlling the visual quality of urban space through the visual quality evaluation on urban street corridors. This study is an early stage as part of the development of ‘Landscape Visual Planning System’ on the commercial street corridor in Malang. Accordingly, the research aims to evaluate the physical characteristics and the public preferences of the spatial and visual aspects in five provincial road corridors in Malang. This study employs a field survey methods, and an environmental aesthetics approach through semantic differential method. The result of the identification of physical characteristics and the assessment of public preferences on the spatial and visual aspects of the five provincial streets serve as the basis for constructing the 3d interactive simulation scenarios in the Landscape Visual Planning System.

Simultaneous determination of 19 flavonoids in commercial trollflowers by using high-performance liquid chromatography and classification of samples by hierarchical clustering analysis.

PubMed

Song, Zhiling; Hashi, Yuki; Sun, Hongyang; Liang, Yi; Lan, Yuexiang; Wang, Hong; Chen, Shizhong

2013-12-01

The flowers of Trollius species, named Jin Lianhua in Chinese, are widely used traditional Chinese herbs with vital biological activity that has been used for several decades in China to treat upper respiratory infections, pharyngitis, tonsillitis, and bronchitis. We developed a rapid and reliable method for simultaneous quantitative analysis of 19 flavonoids in trollflowers by using high-performance liquid chromatography (HPLC). Chromatography was performed on Inertsil ODS-3 C18 column, with gradient elution methanol-acetonitrile-water with 0.02% (v/v) formic acid. Content determination was used to evaluate the quality of commercial trollflowers from different regions in China, while three Trollius species (Trollius chinensis Bunge, Trollius ledebouri Reichb, Trollius buddae Schipcz) were explicitly distinguished by using hierarchical clustering analysis. The linearity, precision, accuracy, limit of detection, and limit of quantification were validated for the quantification method, which proved sensitive, accurate and reproducible indicating that the proposed approach was applicable for the routine analysis and quality control of trollflowers. © 2013.

Influence of PA6 nanocomposite films on the stability of vacuum-aged beef loins during storage in modified atmospheres.

PubMed

Picouet, P A; Fernandez, A; Realini, C E; Lloret, E

2014-01-01

A masterbatch of polyamide 6 (PA6) containing dispersed nanoclays, was used to fabricate a novel multilayer film for vacuum packed meat. Performance of the nanocomposite was compared to a control PA6 multilayer and a high barrier commercial film. Addition of nanoclays improved oxygen barrier properties, UV-blocking capability and stiffness. Beef loins were vacuum-aged using the three films for 0 7, 14 and 21 days at 2°C. After each ageing time, beef steaks were packaged in commercial trays and high oxygen atmosphere and stored at 4°C for 9 days. Beef quality parameters and gas content were studied during display time in MAP (1, 3, 6 and 9 d). Beef quality parameters were not influenced by the packaging materials used during ageing and the performance of nanocomposites was comparable to high barrier films. Ageing had a positive impact on the stabilization of redness up to day 6 in MAP. Thereafter, oxymyoglobin content and oxidation levels were negatively influenced by ageing. © 2013.

Beam uniformity of flat top lasers

NASA Astrophysics Data System (ADS)

Chang, Chao; Cramer, Larry; Danielson, Don; Norby, James

2015-03-01

Many beams that output from standard commercial lasers are multi-mode, with each mode having a different shape and width. They show an overall non-homogeneous energy distribution across the spot size. There may be satellite structures, halos and other deviations from beam uniformity. However, many scientific, industrial and medical applications require flat top spatial energy distribution, high uniformity in the plateau region, and complete absence of hot spots. Reliable standard methods for the evaluation of beam quality are of great importance. Standard methods are required for correct characterization of the laser for its intended application and for tight quality control in laser manufacturing. The International Organization for Standardization (ISO) has published standard procedures and definitions for this purpose. These procedures have not been widely adopted by commercial laser manufacturers. This is due to the fact that they are unreliable because an unrepresentative single-pixel value can seriously distort the result. We hereby propose a metric of beam uniformity, a way of beam profile visualization, procedures to automatically detect hot spots and beam structures, and application examples in our high energy laser production.

Assessing the impact of a school-based safe water intervention on household adoption of point-of-use water treatment practices in southern India.

PubMed

Freeman, Matthew C; Clasen, Thomas

2011-03-01

We assessed a pilot project by UNICEF and Hindustan Unilever Limited to improve the quality of drinking water for children in schools through adoption of improved drinking water practices among households in southern India. The intervention consisted of providing classrooms of 200 schools a commercial water purifier, and providing basic hygiene and water treatment information to students, parents, and teachers. We found no evidence that the intervention was effective in improving awareness or uptake of effective water treatment practices at home. A similar proportion of household members in the intervention and control groups boiled their water (P = 0.60), used a ceramic filtration system (P = 0.33), and used a cloth filter (P = 0.89). One year after the launch of the campaign, household ownership of the commercial purifier promoted at schools was higher in the intervention group (26%) than the control group (19%), but this difference was not statistically significant (P = 0.53).

Quality and provider choice: a multinomial logit-least-squares model with selectivity.

PubMed Central

Haas-Wilson, D; Savoca, E

1990-01-01

A Federal Trade Commission survey of contact lens wearers is used to estimate a multinomial logit-least-squares model of the joint determination of provider choice and quality of care in the contact lens industry. The effect of personal and industry characteristics on a consumer's choice among three types of providers--opticians, ophthalmologists, and optometrists--is estimated via multinomial logit. The regression model of the quality of care has two features that distinguish it from previous work in the area. First, it uses an outcome rather than a structural or process measure of quality. Quality is measured as an index of the presence of seven potentially pathological eye conditions caused by poorly fitted lenses. Second, the model controls for possible selection bias that may arise from the fact that the sample observations on quality are generated by consumers' nonrandom choices of providers. The multinomial logit estimates of provider choice indicate that professional regulations limiting the commercial practices of optometrists shift demand for contact lens services away from optometrists toward ophthalmologists. Further, consumers are more likely to have their lenses fitted by opticians in states that require the licensing of opticians. The regression analysis of variations in quality across provider types shows a strong positive selection bias in the estimate of the quality of care received by consumers of ophthalmologists' services. Failure to control for this selection bias results in an overestimate of the quality of care provided by ophthalmologists. PMID:2312308

The integrated quality assessment of Chinese commercial dry red wine based on a method of online HPLC-DAD-CL combined with HPLC-ESI-MS.

PubMed

Yu, Hai-Xiang; Sun, Li-Qiong; Qi, Jin

2014-07-01

To apply an integrated quality assessment strategy to investigate the quality of multiple Chinese commercial dry red wine samples. A comprehensive method was developed by combining a high performance liquid chromatography-diode array detector-chemiluminescence (HPLC-DAD-CL) online hyphenated system with an HPLC-ESI-MS technique. Chromatographic and H2O2-scavenging active fingerprints of thirteen batches of different, commercially available Chinese dry red wine samples were obtained and analyzed. Twenty-five compounds, including eighteen antioxidants were identified and evaluated. The dominant and characteristic antioxidants in the samples were identified. The relationships between antioxidant potency and the cultivated variety of grape, producing area, cellaring period, and trade mark are also discussed. The results provide the feasibility for an integrated quality assessment strategy to be efficiently and objectively used in quality (especially antioxidant activity) assessment and identification of dry red wine. Copyright © 2014 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.

On the Traceability of Commercial Saffron Samples Using ¹H-NMR and FT-IR Metabolomics.

PubMed

Consonni, Roberto; Ordoudi, Stella A; Cagliani, Laura R; Tsiangali, Maria; Tsimidou, Maria Z

2016-02-29

In previous works on authentic samples of saffron of known history (harvest and processing year, storage conditions, and length of time) some biomarkers were proposed using both FT-IR and NMR metabolomics regarding the shelf life of the product. This work addresses the difficulties to trace back the "age" of commercial saffron samples of unknown history, sets a limit value above which these products can be considered substandard, and offers a useful tool to combat saffron mislabeling and fraud with low-quality saffron material. Investigations of authentic and commercial saffron samples of different origin and harvest year, which had been stored under controlled conditions for different lengths of time, allowed a clear-cut clustering of samples in two groups according to the storage period irrespectively of the provenience. In this respect, the four-year cut off point proposed in our previous work assisted to trace back the "age" of unknown samples and to check for possible mislabeling practices.

Attenuated Total Reflection Mid-Infrared (ATR-MIR) Spectroscopy and Chemometrics for the Identification and Classification of Commercial Tannins.

PubMed

Ricci, Arianna; Parpinello, Giuseppina P; Olejar, Kenneth J; Kilmartin, Paul A; Versari, Andrea

2015-11-01

Attenuated total reflection Fourier transform infrared (FT-IR) spectroscopy was used to characterize 40 commercial tannins, including condensed and hydrolyzable chemical classes, provided as powder extracts from suppliers. Spectral data were processed to detect typical molecular vibrations of tannins bearing different chemical groups and of varying botanical origin (univariate qualitative analysis). The mid-infrared region between 4000 and 520 cm(-1) was analyzed, with a particular emphasis on the vibrational modes in the fingerprint region (1800-520 cm(-1)), which provide detailed information about skeletal structures and specific substituents. The region 1800-1500 cm(-1) contained signals due to hydrolyzable structures, while bands due to condensed tannins appeared at 1300-900 cm(-1) and exhibited specific hydroxylation patterns useful to elucidate the structure of the flavonoid monomeric units. The spectra were investigated further using principal component analysis for discriminative purposes, to enhance the ability of infrared spectroscopy in the classification and quality control of commercial dried extracts and to enhance their industrial exploitation.

Nurses, Inc.: expansion and commercialization of nursing education in the Philippines.

PubMed

Masselink, Leah E; Lee, Shoou-Yih Daniel

2010-07-01

Exporting nurses has been a long-standing economic strategy for the Philippine government, despite the fact that the Philippines' domestic health system is weak and existing supplies of health workers are poorly distributed. This study explores the role of nursing schools as "migrant institutions" in expanding and commercializing nursing education and perpetuating the link between nursing education and migration. Data were collected primarily via in-depth interviews of key informants (nursing school administrators and policymakers) in the Philippines. Results suggest that nursing schools have expanded migration opportunities by making nursing educational available to more students and more diverse student populations. Also, some nursing schools have acted to control the licensure and recruitment processes by establishing commercial relationships with licensure exam review centers and recruitment agencies. These activities perpetuate the culture of migration in the country's nursing profession and indirectly contribute to declining quality of nursing education, misuse of scarce resources, corruption in the nursing sector, and exacerbation of existing health workforce imbalances. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Portable Fourier Transform Spectroscopy for Analysis of Surface Contamination and Quality Control

NASA Technical Reports Server (NTRS)

Pugel, Diane

2012-01-01

Progress has been made into adapting and enhancing a commercially available infrared spectrometer for the development of a handheld device for in-field measurements of the chemical composition of various samples of materials. The intent is to duplicate the functionality of a benchtop Fourier transform infrared spectrometer (FTIR) within the compactness of a handheld instrument with significantly improved spectral responsivity. Existing commercial technology, like the deuterated L-alanine triglycine sulfide detectors (DLATGS), is capable of sensitive in-field chemical analysis. This proposed approach compares several subsystem elements of the FTIR inside of the commercial, non-benchtop system to the commercial benchtop systems. These subsystem elements are the detector, the preamplifier and associated electronics of the detector, the interferometer, associated readout parameters, and cooling. This effort will examine these different detector subsystem elements to look for limitations in each. These limitations will be explored collaboratively with the commercial provider, and will be prioritized to meet the deliverable objectives. The tool design will be that of a handheld gun containing the IR filament source and associated optics. It will operate in a point-and-shoot manner, pointing the source and optics at the sample under test and capturing the reflected response of the material in the same handheld gun. Data will be captured via the gun and ported to a laptop.

Experimental studies of thermal environment and contaminant transport in a commercial aircraft cabin with gaspers on.

PubMed

Li, B; Duan, R; Li, J; Huang, Y; Yin, H; Lin, C-H; Wei, D; Shen, X; Liu, J; Chen, Q

2016-10-01

Gaspers installed in commercial airliner cabins are used to improve passengers' thermal comfort. To understand the impact of gasper airflow on the air quality in a cabin, this investigation measured the distributions of air velocity, air temperature, and gaseous contaminant concentration in five rows of the economy-class section of an MD-82 commercial aircraft. The gaseous contaminant was simulated using SF6 as a tracer gas with the source located at the mouth of a seated manikin close to the aisle. Two-fifths of the gaspers next to the aisle were turned on in the cabin, and each of them supplied air at a flow rate of 0.66 l/s. The airflow rate in the economy-class cabin was controlled at 10 l/s per passenger. Data obtained in a previous study of the cabin with all gaspers turned off were used for comparison. The results show that the jets from the gaspers had a substantial impact on the air velocity and contaminant transport in the cabin. The air velocity in the cabin was higher, and the air temperature slightly more uniform, when the gaspers were on than when they were off, but turning on the gaspers may not have improved the air quality. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Qualitative and nutritional differences in processing tomatoes grown under commercial organic and conventional production systems.

PubMed

Barrett, D M; Weakley, C; Diaz, J V; Watnik, M

2007-11-01

Organically grown products experienced a doubling in percent penetration of organic sales into retail markets during the period from 1997 to 2003; however, there is still a debate over the perceived quality advantage of organically grown fruits and vegetables. In a study focusing on commercial production of processing tomatoes, samples were analyzed from 4 growers with matched organic and conventional fields. For the 4 growers studied, individual analysis of variance results indicated that tomato juice prepared from organically produced tomatoes on some farms was significantly higher in soluble solids ( degrees Brix), higher in consistency, and titratable acidity, but lower in red color, ascorbic acid, and total phenolics content in the microwaved juice. Results were significantly different among specific growers, and this may be attributed to differences in soil type and soil nutrients, tomato cultivar, environmental conditions, or other production-related factors. Higher levels of soluble solids, titratable acidity, and consistency are desirable for the production of tomato paste, in that tomatoes with these attributes may be more flavorful and require less thermal treatment. This has the potential to result both in cost savings from less energy required in paste manufacture and potentially a higher quality product due to less thermal degradation of color, flavor, and nutrients. Future work may involve a larger number of commercial growers and correlation to controlled university research plots.

An Assessment of the Influence of the Industry Distribution Chain on the Oxygen Levels in Commercial Modified Atmosphere Packaged Cheddar Cheese Using Non-Destructive Oxygen Sensor Technology.

PubMed

O' Callaghan, Karen A M; Papkovsky, Dmitri B; Kerry, Joseph P

2016-06-20

The establishment and control of oxygen levels in packs of oxygen-sensitive food products such as cheese is imperative in order to maintain product quality over a determined shelf life. Oxygen sensors quantify oxygen concentrations within packaging using a reversible optical measurement process, and this non-destructive nature ensures the entire supply chain can be monitored and can assist in pinpointing negative issues pertaining to product packaging. This study was carried out in a commercial cheese packaging plant and involved the insertion of 768 sensors into 384 flow-wrapped cheese packs (two sensors per pack) that were flushed with 100% carbon dioxide prior to sealing. The cheese blocks were randomly assigned to two different storage groups to assess the effects of package quality, packaging process efficiency, and handling and distribution on package containment. Results demonstrated that oxygen levels increased in both experimental groups examined over the 30-day assessment period. The group subjected to a simulated industrial distribution route and handling procedures of commercial retailed cheese exhibited the highest level of oxygen detected on every day examined and experienced the highest rate of package failure. The study concluded that fluctuating storage conditions, product movement associated with distribution activities, and the possible presence of cheese-derived contaminants such as calcium lactate crystals were chief contributors to package failure.

An Assessment of the Influence of the Industry Distribution Chain on the Oxygen Levels in Commercial Modified Atmosphere Packaged Cheddar Cheese Using Non-Destructive Oxygen Sensor Technology

PubMed Central

O’ Callaghan, Karen A.M.; Papkovsky, Dmitri B.; Kerry, Joseph P.

2016-01-01

The establishment and control of oxygen levels in packs of oxygen-sensitive food products such as cheese is imperative in order to maintain product quality over a determined shelf life. Oxygen sensors quantify oxygen concentrations within packaging using a reversible optical measurement process, and this non-destructive nature ensures the entire supply chain can be monitored and can assist in pinpointing negative issues pertaining to product packaging. This study was carried out in a commercial cheese packaging plant and involved the insertion of 768 sensors into 384 flow-wrapped cheese packs (two sensors per pack) that were flushed with 100% carbon dioxide prior to sealing. The cheese blocks were randomly assigned to two different storage groups to assess the effects of package quality, packaging process efficiency, and handling and distribution on package containment. Results demonstrated that oxygen levels increased in both experimental groups examined over the 30-day assessment period. The group subjected to a simulated industrial distribution route and handling procedures of commercial retailed cheese exhibited the highest level of oxygen detected on every day examined and experienced the highest rate of package failure. The study concluded that fluctuating storage conditions, product movement associated with distribution activities, and the possible presence of cheese-derived contaminants such as calcium lactate crystals were chief contributors to package failure. PMID:27331815

Selected metal levels of commercially valuable seaweeds adjacent to and distant from point sources of contamination in Nova Scotia and New Brunswick

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharp, G.J.; Samant, H.S.; Vaidya, O.C.

1988-06-01

The harvesting of marine plants on a commercial scale was a significant industry in the Maritime Provinces of Canada by the end of World War II. These seaweeds have been traditionally utilized as foodstuffs either as a processed extract or a semi-processed plant. The Maritime coastline is becoming industrialized; there is also potential for expansion of the marine plant industry beyond traditional harvest areas. Therefore, the quality of material from new areas must be examined prior to exploitation as well as monitoring of traditional areas. The bioaccumulated of metals by marine plants was recognized in early measurements of trace elementmore » concentrations which were above ambient water values. Before growth and reproductive inhibition are caused by severe effects of heavy metal pollution, food quality changes may occur. The Food Chemical Code (U.S.A.) limits heavy metals in the extracts of seaweeds. Sediment and water samples taken in connection with the Ocean Dumping Control Act of Canada have identified several sites with elevated heavy metal content in the Maritimes. The purpose of this study was to examine heavy metal levels in commercially important seaweeds from traditional harvest areas and areas near point sources of pollution. The authors wished to provide a baseline for the future and identify existing problem areas.« less

SPINOFF 2000

NASA Technical Reports Server (NTRS)

2000-01-01

For the past 42 years, NASA has made special efforts to ensure the widest possible dissemination of its research and technology developments. We share the wealth of technology developed for our missions with the nation's industries to contribute to US economic strength and quality of life. For the past 27 years, this publication has provided you with over 1,200 examples of products and services developed as a direct result of commercial partnerships between NASA and the business community. Examples have covered products from fire retardant materials and air pollution monitors to non-invasive cardiac monitors and sensors for environmental control. In the Technology Transfer and Outreach section of Spinoff 2000, we highlight the activities of our Ames Research Center's Commercial Technology Office (CTO). Their efforts to facilitate and support technology commercialization are representative of the CTO at each field center. Increased activities to accelerate the dissemination of technologies, speed up the process of patent licensing, quicken the release of software for beta testing, support and manage incubators, and hasten the collaboration with commercial and academic organizations will continue to maximize the earliest potential commercial utilization of NASA's new inventions and technologies. Spinoff 2000 is organized into three sections: (1) Aerospace and Development highlights major research and development efforts currently carried out at the 10 NASA field centers; (2) Commercial Benefits-Spinoffs describes commercially available products and services resulting from the transfer of NASA technology; and (3) Technology Transfer and Outreach features this year's center spotlight, NASA's Ames Research Center, and its commercialization efforts, as well as the mechanisms in place nationwide to assist US industry in obtaining, transferring, and applying NASA technology, expertise, and assistance.

Job satisfaction of occupational physicians in commercial and other delivery settings: a comparative and explorative study.

PubMed

Plomp, Harmen Nico; van der Beek, Allard J

2014-08-01

Commercialization of occupational health services (OHS) and transition to a supplier market which started in 1995, has affected work and working conditions of occupational physicians (OPs) profoundly. OPs have lost influence on the organization of their work and managers took over control. This study explores the impact of commercialization on job satisfaction of occupational physicians. Data were collected through a questionnaire completed by 797 OPs, members of the Netherlands Association of Occupational Medicine (response: 45%). A range of work satisfiers and dissatisfiers measures was included that, according to the Social Action Approach, could explain the variation in job satisfaction. Stepwise multivariate regression analyses were performed to explore to what extent the differences in job satisfaction can be attributed to the characteristics of the setting, biographical variables, satisfiers and dissatisfiers. Occupational physicians in commercial settings had the lowest average score as regards job satisfaction (6.7) contrasting sharply with their colleagues in private practices (8.7) and in non-commercial settings (7.9). The variation in job satisfaction between delivery settings could largely be attributed to satisfiers and dissatisfiers. Biographical characteristics (age, gender) had no effect. The data suggested that not commercialization as such, but the ability of commercial OHS providers to integrate professional values was the crucial factor to bring about job satisfaction. The challenge for commercial OHS providers is to preserve the professional zeal in OPs by integrating professional values in their organization in order to improve the quality of the services and the attractiveness of the profession.

COMPARISON OF ARCHITECT I 2000 FOR DETERMINATION OF CYCLOSPORINE WITH AXSYM

PubMed Central

Serdarevic, Nafija; Zunic, Lejla

2012-01-01

Background: Cyclosporine has been shown effective drug in suppressing acute rejection in recipients of allograft organ transplants. Methods: The cyclosporine concentration of 96 blood samples was determined using CMIA (chemiluminesecent microparticle immnoassay) Architect i 2000 and FPIA (fluorescence polarization immunoassay) AxSYM Abbott diagnostic. All patients have transplantation of kidneys and were hospitalized at Department of Nephrology at the Clinical center of University of Sarajevo. The reference serum range of cyclosporine for kidney organ transplantation for maintenance lies between 50 and 150 ng/mL. The quality control, precision and accurancy of Architect i 2000 were assessed. Results: The quality control was done using quality control serums for low (= 91 ng/mL), medium (= 328 ng/mL) and high (= 829 ng/mL). We have used commercial BIORAD controls and got reproducibility CV 5.83 % to 13 % for Architect i 2000. It was established that the main difference between Architect i 2000 and AxSYM and it was statistically significant for P < 0.05 according to Student t-test. Correlation coefficient was r = 0.903. Conclusion: The CMIA Architect assay has significant reduced cyclosporine metabolite interference relative to other immunoassay and is a convenient and sensitive automated method to measure cyclosporine in whole blood. PMID:23378685

Xenoesterogens and male infertility: myth or reality?

PubMed

Rozati, R; Reddy, P P; Reddanna, P; Mujtaba, R

2000-12-01

To evaluate the role of polychlorinated biphenyls (PCBs) as a potential environmental hazard in the deterioration of male fertility. Fifty-three males were studied. After a thorough case history evaluation and relevant clinical and laboratory investigations, PCBs were estimated in the seminal plasma of 21 infertile men with "Unexplained Male Factor" and 32 fertile controls. Peak retention times of the eluants were compared with those of the commercially available standard PCB Mix, and the results confirmed spectrophotometrically. Seminal PCB concentrations were compared between i) fertile and infertile men and ii) men from different areas and diets. The relationship between PCB concentrations and measures of sperm quality such as the total motile sperm count, was assessed. PCBs were detected in seminal plasma of infertile men but absent from controls. Sperm quantity and quality were significantly lower in infertile men compared to controls. The highest average PCB concentrations were found in fish-eating urban dwellers, and followed in succession by fish-eating rural dwellers, non fish-eating urban dwellers and non fish-eating rural dwellers. The total motile sperm counts were inversely proportional to the PCB concentrations and were significantly lower than those of the respective controls. PCBs may be instrumental in the deterioration of sperm quantity and quality, a contaminated fish diet being the main source of exposure.

Cooking Can Be Profitable; Commercial Cooking and Baking 1:9193.03.

ERIC Educational Resources Information Center

Dade County Public Schools, Miami, FL.

The course outline is prepared as a guide for the 10th grade student in Commercial Cooking and Baking or Food Management Production and Service. The course introduces the student to effective production of high quality foods and develops an understanding of high standards in quality food service. Totaling 90 hours of instruction, nine blocks of…

APPLICATION OF A FUNCTIONAL MATHEMATICAL QUALITY INDEX TO ASPARAGINE, FREE SUGAR AND PHENOLIC ACID CONTENT OF 20 COMMERCIAL POTATO VARIETIES

USDA-ARS?s Scientific Manuscript database

In this article, we apply a functional mathematical index (FMI), introduced in a previous publication, to 20 commercial potato varieties. The index allows evaluation of nutritional, safety and processing “quality parameters” of different potato cultivars. The main goal of the index is to link the q...

[Analysis of commercial specifications and grades of wild and cultivated Gentianae Macrophyllae Radix based on multi-indicative constituents].

PubMed

Yang, Yan-Mei; Lin, Li; Lu, You-Yuan; Ma, Xiao-Hui; Jin, Ling; Zhu, Tian-Tian

2016-03-01

The study is aimed to analyze the commercial specifications and grades of wild and cultivated Gentianae Macrophllae Radix based on multi-indicative constituents. The seven kinds of main chemical components containing in Gentianae Macrophyllae Radix were determined by UPLC, and then the quality levels of chemical component of Gentianae Macrophyllae Radix were clustered and classified by modern statistical methods (canonical correspondence analysis, Fisher discriminant analysis and so on). The quality indices were selected and their correlations were analyzed. Lastly, comprehensively quantitative grade division for quality under different commodity-specifications and different grades of same commodity-specifications of wild and planting were divided. The results provide a basis for a reasonable division of specification and grade of the commodity of Gentianae Macrophyllae Radix. The range of quality evaluation of main index components (gentiopicrin, loganin acid and swertiamarin) was proposed, and the Herbal Quality Index (HQI) was introduced. The rank discriminant function was established based on the quality by Fisher discriminant analysis. According to the analysis, the quality of wild and cultivated Luobojiao, one of the commercial specification of Gentianae Macrophyllae Radix was the best, Mahuajiao, the other commercial specification, was average , Xiaoqinjiao was inferior. Among grades, the quality of first-class cultivated Luobojiao was the worst, of second class secondary, and the third class the best; The quality of the first-class of wild Luobojiao was secondary, and the second-class the best; The quality of the second-class of Mahuajiao was secondary, and the first-class was the best; the quality of first-class Xiaoqinjiao was secondary, and the second-class was the better one between the two grades, but not obvious significantly. The method provides a new idea and method for evaluation of comprehensively quantitative on the quality of Gentianae Macrophyllae Radix. Copyright© by the Chinese Pharmaceutical Association.

Design of Interline Unified Power Quality Conditioner for Power Quality Disturbances using Simulink

NASA Astrophysics Data System (ADS)

Kumaraswamy, G.; Reddy, Y. Rajasekhar; Harikrishna, Ch.

2012-10-01

Proliferation of electronic equipment in commercial and industrial processes has resulted in increasingly sensitive electrical loads to be fed from power distribution system which introduce contamination to voltage and current waveforms at the point of common coupling of industrial loads. The unified power quality conditioner (UPQC) is connected between two different feeders (lines), hence this method of connection of the UPQC is called as Interline UPQC (IUPQC).This paper proposes a new connection for a UPQC to improve the power quality of two feeders in a distribution system. Interline Unified Power Quality Conditioner (IUPQC), specifically aims at the integration of series VSC and Shunt VSC to provide high quality power supply by means of voltage sag/swell compensation, harmonic elimination and power factor correction in a power distribution network, so that improved power quality can be made available at the point of common coupling. The structure, control and capability of the IUPQC are discussed in this paper. The efficiency of the proposed configuration has been verified through simulation using MATLAB/ SIMULINK.

Field Demonstration and Validation of a New Device for Measuring Water and Solute Fluxes at CFB Borden

DTIC Science & Technology

2006-11-01

All Quality Control Reference Materials are acquired only from authorized vendors or sources commonly used by U.S. EPA Regional Laboratories...Institue of Standards and Testing (NITS) Standard Reference Materials (SRM) or to the U.S. EPA Reference Standards. Working Standards The commercial...contaminants from clothing or equipment by blowing, shaking or any other means that may disperse material into the air is prohibited. 7.1.3. All disposable

Seasonal Variation in Drinking and Domestic Water Sources and Quality in Port Harcourt, Nigeria.

PubMed

Kumpel, Emily; Cock-Esteb, Alicea; Duret, Michel; de Waal, Dominick; Khush, Ranjiv

2017-02-08

We compared dry and rainy season water sources and their quality in the urban region of Port Harcourt, Nigeria. Representative sampling indicated that municipal water supplies represent < 1% of the water sources. Residents rely on privately constructed and maintained boreholes that are supplemented by commercially packaged bottled and sachet drinking water. Contamination by thermotolerant coliforms increased from 21% of drinking water sources in the dry season to 42% of drinking water sources in the rainy season ( N = 356 and N = 397). The most significant increase was in sachet water, which showed the lowest frequencies of contamination in the dry season compared with other sources (15%, N = 186) but the highest frequencies during the rainy season (59%, N = 76). Only half as many respondents reported drinking sachet water in the rainy season as in the dry season. Respondents primarily used flush or pour-flush toilets connected to septic tanks (85%, N = 399). The remainder relied on pit latrines and hanging (pier) latrines that drained into surface waters. We found significant associations between fecal contamination in boreholes and the nearby presence of hanging latrines. Sanitary surveys of boreholes showed that more than half were well-constructed, and we did not identify associations between structural or site deficiencies and microbial water quality. The deterioration of drinking water quality during the rainy season is a serious public health risk for both untreated groundwater and commercially packaged water, highlighting a need to address gaps in monitoring and quality control. © The American Society of Tropical Medicine and Hygiene.

When Spreadsheets Become Software - Quality Control Challenges and Approaches - 13360

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fountain, Stefanie A.; Chen, Emmie G.; Beech, John F.

2013-07-01

As part of a preliminary waste acceptance criteria (PWAC) development, several commercial models were employed, including the Hydrologic Evaluation of Landfill Performance model (HELP) [1], the Disposal Unit Source Term - Multiple Species model (DUSTMS) [2], and the Analytical Transient One, Two, and Three-Dimensional model (AT123D) [3]. The results of these models were post-processed in MS Excel spreadsheets to convert the model results to alternate units, compare the groundwater concentrations to the groundwater concentration thresholds, and then to adjust the waste contaminant masses (based on average concentration over the waste volume) as needed in an attempt to achieve groundwater concentrationsmore » at the limiting point of assessment that would meet the compliance concentrations while maximizing the potential use of the landfill (i.e., maximizing the volume of projected waste being generated that could be placed in the landfill). During the course of the PWAC calculation development, one of the Microsoft (MS) Excel spreadsheets used to post-process the results of the commercial model packages grew to include more than 575,000 formulas across 18 worksheets. This spreadsheet was used to assess six base scenarios as well as nine uncertainty/sensitivity scenarios. The complexity of the spreadsheet resulted in the need for a rigorous quality control (QC) procedure to verify data entry and confirm the accuracy of formulas. (authors)« less

SPRT Calibration Uncertainties and Internal Quality Control at a Commercial SPRT Calibration Facility

NASA Astrophysics Data System (ADS)

Wiandt, T. J.

2008-06-01

The Hart Scientific Division of the Fluke Corporation operates two accredited standard platinum resistance thermometer (SPRT) calibration facilities, one at the Hart Scientific factory in Utah, USA, and the other at a service facility in Norwich, UK. The US facility is accredited through National Voluntary Laboratory Accreditation Program (NVLAP), and the UK facility is accredited through UKAS. Both provide SPRT calibrations using similar equipment and procedures, and at similar levels of uncertainty. These uncertainties are among the lowest available commercially. To achieve and maintain low uncertainties, it is required that the calibration procedures be thorough and optimized. However, to minimize customer downtime, it is also important that the instruments be calibrated in a timely manner and returned to the customer. Consequently, subjecting the instrument to repeated calibrations or extensive repeated measurements is not a viable approach. Additionally, these laboratories provide SPRT calibration services involving a wide variety of SPRT designs. These designs behave differently, yet predictably, when subjected to calibration measurements. To this end, an evaluation strategy involving both statistical process control and internal consistency measures is utilized to provide confidence in both the instrument calibration and the calibration process. This article describes the calibration facilities, procedure, uncertainty analysis, and internal quality assurance measures employed in the calibration of SPRTs. Data will be reviewed and generalities will be presented. Finally, challenges and considerations for future improvements will be discussed.

Controlled electrostatic methodology for imaging indentations in documents.

PubMed

Yaraskavitch, Luke; Graydon, Matthew; Tanaka, Tobin; Ng, Lay-Keow

2008-05-20

The electrostatic process for imaging indentations on documents using the ESDA device is investigated under controlled experimental settings. An in-house modified commercial xerographic developer housing is used to control the uniformity and volume of toner deposition, allowing for reproducible image development. Along with this novel development tool, an electrostatic voltmeter and fixed environmental conditions facilitate an optimization process. Sample documents are preconditioned in a humidity cabinet with microprocessor control, and the significant benefit of humidification above 70% RH on image quality is verified. Improving on the subjective methods of previous studies, image quality analysis is carried out in an objective and reproducible manner using the PIAS-II. For the seven commercial paper types tested, the optimum ESDA operating point is found to be at an electric potential near -400V at the Mylar surface; however, for most paper types, the optimum operating regime is found to be quite broad, spanning relatively small electric potentials between -200 and -550V. At -400V, the film right above an indented area generally carries a voltage which is 30-50V less negative than the non-indented background. In contrast with Seward's findings [G.H. Seward, Model for electrostatic imaging of forensic evidence via discharge through Mylar-paper path, J. Appl. Phys. 83 (3) (1998) 1450-1456; G.H. Seward, Practical implications of the charge transport model for electrostatic detection apparatus (ESDA), J. Forensic Sci. 44 (4) (1999) 832-836], a period of charge decay before image development is not required when operating in this optimal regime. A brief investigation of the role played by paper-to-paper friction during the indentation process is conducted using our optimized development method.

Minimising losses to predation during microalgae cultivation.

PubMed

Flynn, Kevin J; Kenny, Philip; Mitra, Aditee

2017-01-01

We explore approaches to minimise impacts of zooplanktonic pests upon commercial microalgal crops using system dynamics models to describe algal growth controlled by light and nutrient availability and zooplankton growth controlled by crop abundance and nutritional quality. Losses of microalgal crops are minimised when their growth is fastest and, in contrast, also when growing slowly under conditions of nutrient exhaustion. In many culture systems, however, dwindling light availability due to self-shading in dense suspensions favours slow growth under nutrient sufficiency. Such a situation improves microalgal quality as prey, enhancing zooplankton growth, and leads to rapid crop collapse. Timing of pest entry is important; crop losses are least likely in established, nutrient-exhausted microalgal communities grown for high C-content (e.g. for biofuels). A potentially useful approach is to promote a low level of P-stress that does not adversely affect microalgal growth but which produces a crop that is suboptimal for zooplankton growth.

Flight service evaluation of an advanced composite empennage component on commercial transport aircraft. Phase 1: Engineering development

NASA Technical Reports Server (NTRS)

Ary, A.; Axtell, C.; Fogg, L.; Jackson, A.; James, A. M.; Mosesian, B.; Vanderwier, J.; Vanhamersveld, J.

1976-01-01

The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes the front and rear spars. Various design options were evaluated to arrive at a configuration which would offer the highest potential for satisfying program objectives. The preferred configuration selected consists of a hat-stiffened cover with molded integrally stiffened spars, aluminum trussed composite ribs, and composite miniwich web ribs with integrally molded caps. Material screening tests were performed to select an advanced composite material system for the Advanced Composite Vertical Fin (ACFV) that would meet the program requirements from the standpoint of quality, reproducibility, and cost. Preliminary weight and cost analysis were made, targets established, and tracking plans developed. These include FAA certification, ancillary test program, quality control, and structural integrity control plans.

Commercial lumber, round timbers, and ties

Treesearch

David E. Kretschmann

2010-01-01

When sawn, a log yields round timber, ties, or lumber of varying quality. This chapter presents a general discussion of grading, standards, and specifications for these commercial products. In a broad sense, commercial lumber is any lumber that is bought or sold in the normal channels of commerce. Commercial lumber may be found in a variety of forms, species, and types...

76 FR 15607 - National Emission Standards for Hazardous Air Pollutants for Major Sources: Industrial...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-21

...On September 13, 2004, under authority of section 112 of the Clean Air Act, EPA promulgated national emission standards for hazardous air pollutants for new and existing industrial/commercial/ institutional boilers and process heaters. On June 19, 2007, the United States Court of Appeals for the District of Columbia Circuit vacated and remanded the standards. In response to the Court's vacatur and remand, EPA is, in this action, establishing emission standards that will require industrial/ commercial/institutional boilers and process heaters located at major sources to meet hazardous air pollutants standards reflecting the application of the maximum achievable control technology. This rule protects air quality and promotes public health by reducing emissions of the hazardous air pollutants listed in section 112(b)(1) of the Clean Air Act.

Isolated Operation at Hachinohe Micro-Grid Project

NASA Astrophysics Data System (ADS)

Takano, Tomihiro; Kojima, Yasuhiro; Temma, Koji; Simomura, Masaru

To meet the global warming, renewable energy sources like wind, solar and biomass generations are dramatically increasing. Cogeneration systems are also ever-growing to save consumers' energy costs among factories, buildings and homes where lots of thermal loads are expected. According to these dispersed generators growth, their negative impacts to commercial power systems quality become non-negligible, because their unstable output causes network voltage and frequency fluctuation. Micro-grid technology comes to the front to solve the problem and many demonstrative field tests are now going all over the world. This paper presents the control paradigm and its application to Hachinohe micro-gird project, especially focusing on the power quality at isolated operation on which strict condition is imposed.

Automated surface quality inspection with ARGOS: a case study

NASA Astrophysics Data System (ADS)

Kiefhaber, Daniel; Etzold, Fabian; Warken, Arno F.; Asfour, Jean-Michel

2017-06-01

The commercial availability of automated inspection systems for optical surfaces specified according to ISO 10110-7 promises unsupervised and automated quality control with reproducible results. In this study, the classification results of the ARGOS inspection system are compared to the decisions by well-trained inspectors based on manual-visual inspection. Both are found to agree in 93.6% of the studied cases. Exemplary cases with differing results are studied, and shown to be partly caused by shortcomings of the ISO 10110-7 standard, which was written for the industry standard manual-visual inspection. Applying it to high resolution images of the whole surface of objective machine vision systems brings with it a few challenges which are discussed.

Black dimensional stones: Geology, technical properties and deposit characterization of the dolerites from Uruguay

NASA Astrophysics Data System (ADS)

Morales Demarco, M.; Oyhantçabal, P.; Stein, K.-J.; Siegesmund, S.

2012-04-01

Dimensional stones with a black color occupy a prominent place on the international market. Uruguayan dolerite dikes of andesitic and andesitic-basaltic composition are mined for commercial blocks of black dimensional stones. A total of 16 dikes of both compositions were studied and samples collected for geochemical and petrographical analysis. Color measurements were performed on different black dimensional stones in order to compare them with the Uruguayan dolerites. Samples of the two commercial varieties (Absolute Black and Moderate Black) were obtained for petrophysical analysis (e.g. density, porosity, uniaxial compressive strength, tensile strength, etc.). Detailed structural analyses were performed in several quarries. Geochemistry and petrography determines the intensity of the black color. When compared with commercial samples from China, Brazil, India and South Africa, among others, the Uruguayan dolerite Absolute Black is the darkest black dimensional stone analyzed. In addition, the petrophysical properties of the Uruguayan dolerites make them one of the highest quality black dimensional stones. Structural analyses show that five joint sets have been recognized: two sub-vertical joints, one horizontal and two diagonal. These joint sets are one of the most important factors that control the deposits, since they control the block size distribution and the amount of waste material.

48 CFR 46.709 - Warranties of commercial items.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Warranties of commercial items. 46.709 Section 46.709 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Warranties 46.709 Warranties of commercial items. The contracting...

Evaluation of Commercially Available Chikungunya Virus Immunoglobulin M Detection Assays

PubMed Central

Johnson, Barbara W.; Goodman, Christin H.; Holloway, Kimberly; de Salazar, P. Martinez; Valadere, Anne M.; Drebot, Michael A.

2016-01-01

Commercial chikungunya virus (CHIKV)–specific IgM detection kits were evaluated at the Centers for Disease Control and Prevention (CDC), the Public Health Agency of Canada National Microbiology Laboratory, and the Caribbean Public Health Agency (CARPHA). The Euroimmun Anti-CHIKV IgM ELISA kit had ≥ 95% concordance with all three reference laboratory results. The limit of detection for low CHIK IgM+ samples, as measured by serial dilution of seven sera up to 1:12,800 ranged from 1:800 to 1:3,200. The Euroimmun IIFT kit evaluated at CDC and CARPHA performed well, but required more retesting of equivocal results. The InBios CHIKjj Detect MAC-ELISA had 100% and 98% concordance with CDC and CARPHA results, respectively, and had equal sensitivity to the CDC MAC-ELISA to 1:12,800 dilution in serially diluted samples. The Abcam Anti-CHIKV IgM ELISA had high performance at CARPHA, but at CDC, performance was inconsistent between lots. After replacement of the biotinylated IgM antibody controls with serum containing CHIKV-specific IgM and additional quality assurance/control measures, the Abcam kit was rereleased and reevaluated at CDC. The reformatted Abcam kit had 97% concordance with CDC results and limit of detection of 1:800 to 1:3,200. Two rapid tests and three other CHIKV MAC-ELISAs evaluated at CDC had low sensitivity, as the CDC CHIKV IgM in-house positive controls were below the level of detection. In conclusion, laboratories have options for CHIKV serological diagnosis using validated commercial kits. PMID:26976887

Ultra high performance liquid chromatography coupled with triple quadrupole mass spectrometry and chemometric analysis of licorice based on the simultaneous determination of saponins and flavonoids.

PubMed

Jiang, Zhenzuo; Wang, Yuefei; Zheng, Yunfeng; Yang, Jing; Zhang, Lei

2016-08-01

Licorice is among the most popular herbal medicines and frequently used in traditional medicine, food products, and cosmetics. In China, only Glycyrrhiza uralensis Fisch., Glycyrrhiza inflata Bat. and Glycyrrhiza glabra L. are officially used and are usually processed with honey prior to use. To maintain the quality of commercially available herbal products, a simple, rapid, and reliable ultra high performance liquid chromatography with triple quadrupole mass spectrometry was developed to investigate the major active constituents of commercially available licorice products. Nineteen components were accurately determined, including eight triterpenoid saponins, one triterpene, and ten flavonoids. Subsequently, multivariate statistical analysis methods were employed to further explore and interpret the experimental data. The results indicated that liquiritin apioside may be considered as a candidate index for the quality control of licorice as well as 18β-glycyrrhizic acid and liquiritin. In addition, both 18β-glycyrrhizic acid and licorice-saponin G2 can be used for discrimination between crude and honey-processed licorice. Furthermore, using 18β-glycyrrhizic acid and liquiritin as markers, this work revealed that the quality of licorice products may have declined in recent years. This highlights the need for additional effort focused on good agricultural practice during the processing of licorice. In summary, this study provides a valuable reference for the quality assessment of licorice. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Commercialization of New Beam Applications

NASA Astrophysics Data System (ADS)

McKeown, Joseph

1996-05-01

The commercialization of electron processing applications is driven by demonstrated technical advantages over current practice. Mature and reliable accelerator technology has permitted more consistent product quality and the development of new processes. However, the barriers to commercial adoption are often not amenable to solution within the laboratory alone. Aspects of the base accelerator technology, plant engineering, production, project management, financing, regulatory control, product throughput and plant operational efficiency all contribute to the business risk. Experiences in building three 10 MeV, 50 kW, IMPELA electron accelerators at approximately 8 M each and achieving cumulative operational availability greater than 98% in commercial environments have identified key parameters defining those aspects. The allowed ranges of these parameters to generate the 1.5 M annual revenue that is typically necessary to support outlays of this scale are presented. Such data have been used in proposals to displace expensive chemicals in the viscose industry, sterilize sewage sludge, detoxify chemically contaminated soils and build radiation service centers for a diversity of applications. The proposals face stiff competition from traditional chemical methods. Quantitative technical and business details of these activities are provided and an attempt is made to establish realistic expectations for the exploitation of electron beam technologies in emerging applications.

Stormwater-runoff data for a commercial area, Broward County, Florida

USGS Publications Warehouse

Miller, Robert A.; Mattraw, H.C.; Hardee, Jack

1979-01-01

Rainfall, stormwater discharge, and water-quality data for rainfall and runoff are summarized for a commercial area in Fort Lauderdale, Florida. Loads for 20 water-quality constituents were computed for runoff from 31 storms between May 1975 and June 1977. The basin of 20.4 acres contains a shopping center with adjacent parking, and is 97.9 percent impervious. (Woodard-USGS)

Safe Drinking Water and Satisfaction with Environmental Quality of Life in Some Oil and Gas Industry Impacted Cities of Nigeria

ERIC Educational Resources Information Center

Ejechi, E. O.; Ejechi, B. O.

2008-01-01

The availability and safety of drinking water and the environmental quality of life was investigated in five cities located in an oil-producing area of Nigeria using questionnaire-based scales, discussion and laboratory tests. Polythene-packaged sachet water and commercial and non-commercial private boreholes largely met the drinking water…

Effect of a commercial housing system on egg quality during extended storage.

PubMed

Jones, D R; Karcher, D M; Abdo, Z

2014-05-01

Egg producers in the United States are utilizing a variety of commercial egg production systems to provide consumer choice and meet legislative requirements. Consumer egg grades in the United States were developed for conventional cage production, and it is unclear what effect alternative production systems might have on egg quality during retail and consumer home storage. The current study was undertaken to determine what changes in egg quality characteristics occur during extended cold storage for commercially produced conventional cage, enriched colony cage, and cage-free aviary eggs. During 12 wk of cold storage, egg weight, albumen height, Haugh unit, static compression shell strength, vitelline membrane strength and deformation, yolk index, shell dynamic stiffness, and whole egg total solids were monitored. Overall, aviary and enriched eggs were significantly (P < 0.05) heavier than conventional cage. Albumen height and Haugh unit (P < 0.05) were significantly greater for conventional cage than enriched eggs. Static compression shell strength was greatest (P < 0.05) for enriched eggs compared with aviary. No overall housing system effects for yolk measurements, shell dynamic stiffness, or whole egg total solids were observed. Albumen height, Haugh unit, and yolk quality measurements were all greatest at 0 and lowest at 12 wk of storage (P < 0.05). The rate of quality change among the housing systems for each measured attribute at 4, 6, and 12 wk was determined. Other than differences in the change of egg weight at 4 wk, no significant differences in the rate of quality decline were found among the housing systems. The results of the current study indicate that current US egg quality standards should effectively define quality for commercially produced conventional cage, enriched colony cage, and cage-free aviary eggs.

Researcher responsibilities and genetic counseling for pure-bred dog populations.

PubMed

Bell, Jerold S

2011-08-01

Breeders of dogs have ethical responsibilities regarding the testing and management of genetic disease. Molecular genetics researchers have their own responsibilities, highlighted in this article. Laboratories offering commercial genetic testing should have proper sample identification and quality control, official test result certificates, clear explanations of test results and reasonably priced testing fees. Providing test results to a publicly-accessible genetic health registry allows breeders and the public to search for health-tested parents to reduce the risk of producing or purchasing affected offspring. Counseling on the testing and elimination of defective genes must consider the effects of genetic selection on the population. Recommendations to breed quality carriers to normal-testing dogs and replacing them with quality normal-testing offspring will help to preserve breeding lines and breed genetic diversity. Copyright © 2011 Elsevier Ltd. All rights reserved.

NASA S and MA at the Crossroads; The Role of NASA Quality Insight/Oversight for Commercial Crewed Launch Vehicles

NASA Technical Reports Server (NTRS)

Malone, Roy W., Jr.

2010-01-01

The presentation slides examine: The Journey, Current Safety and Mission Assurance (S and MA) Oversight/Insight, The Change, The Issue, Potential NASA relationship with Commercial Partners, and Commercial "X" FRR - Are you Go.

Implementation of quality by design toward processing of food products.

PubMed

Rathore, Anurag S; Kapoor, Gautam

2017-05-28

Quality by design (QbD) is a systematic approach that begins with predefined objectives and emphasizes product and process understanding and process control. It is an approach based on principles of sound science and quality risk management. As the food processing industry continues to embrace the idea of in-line, online, and/or at-line sensors and real-time characterization for process monitoring and control, the existing gaps with regard to our ability to monitor multiple parameters/variables associated with the manufacturing process will be alleviated over time. Investments made for development of tools and approaches that facilitate high-throughput analytical and process development, process analytical technology, design of experiments, risk analysis, knowledge management, and enhancement of process/product understanding would pave way for operational and economic benefits later in the commercialization process and across other product pipelines. This article aims to achieve two major objectives. First, to review the progress that has been made in the recent years on the topic of QbD implementation in processing of food products and second, present a case study that illustrates benefits of such QbD implementation.

Ensuring the Quality of Stem Cell-Derived In Vitro Models for Toxicity Testing.

PubMed

Stacey, Glyn N; Coecke, Sandra; Price, Anna-Bal; Healy, Lyn; Jennings, Paul; Wilmes, Anja; Pinset, Christian; Ingelman-Sundberg, Magnus; Louisse, Jochem; Haupt, Simone; Kidd, Darren; Robitski, Andrea; Jahnke, Heinz-Georg; Lemaitre, Gilles; Myatt, Glenn

Quality control of cell cultures used in new in vitro toxicology assays is crucial to the provision of reliable, reproducible and accurate toxicity data on new drugs or constituents of new consumer products. This chapter explores the key scientific and ethical criteria that must be addressed at the earliest stages of developing toxicology assays based on human pluripotent stem cell (hPSC) lines. It also identifies key considerations for such assays to be acceptable for regulatory, laboratory safety and commercial purposes. Also addressed is the development of hPSC-based assays for the tissue and cell types of greatest interest in drug toxicology. The chapter draws on a range of expert opinion within the European Commission/Cosmetics Europe-funded alternative testing cluster SEURAT-1 and consensus from international groups delivering this guidance such as the International Stem Cell Banking Initiative. Accordingly, the chapter summarizes the most up-date best practices in the use and quality control of human Pluripotent Stem Cell lines in the development of in vitro toxicity assays from leading experts in the field.

SU-E-T-268: Differences in Treatment Plan Quality and Delivery Between Two Commercial Treatment Planning Systems for Volumetric Arc-Based Radiation Therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, S; Zhang, H; Zhang, B

2015-06-15

Purpose: To clinically evaluate the differences in volumetric modulated arc therapy (VMAT) treatment plan and delivery between two commercial treatment planning systems. Methods: Two commercial VMAT treatment planning systems with different VMAT optimization algorithms and delivery approaches were evaluated. This study included 16 clinical VMAT plans performed with the first system: 2 spine, 4 head and neck (HN), 2 brain, 4 pancreas, and 4 pelvis plans. These 16 plans were then re-optimized with the same number of arcs using the second treatment planning system. Planning goals were invariant between the two systems. Gantry speed, dose rate modulation, MLC modulation, planmore » quality, number of monitor units (MUs), VMAT quality assurance (QA) results, and treatment delivery time were compared between the 2 systems. VMAT QA results were performed using Mapcheck2 and analyzed with gamma analysis (3mm/3% and 2mm/2%). Results: Similar plan quality was achieved with each VMAT optimization algorithm, and the difference in delivery time was minimal. Algorithm 1 achieved planning goals by highly modulating the MLC (total distance traveled by leaves (TL) = 193 cm average over control points per plan), while maintaining a relatively constant dose rate (dose-rate change <100 MU/min). Algorithm 2 involved less MLC modulation (TL = 143 cm per plan), but greater dose-rate modulation (range = 0-600 MU/min). The average number of MUs was 20% less for algorithm 2 (ratio of MUs for algorithms 2 and 1 ranged from 0.5-1). VMAT QA results were similar for all disease sites except HN plans. For HN plans, the average gamma passing rates were 88.5% (2mm/2%) and 96.9% (3mm/3%) for algorithm 1 and 97.9% (2mm/2%) and 99.6% (3mm/3%) for algorithm 2. Conclusion: Both VMAT optimization algorithms achieved comparable plan quality; however, fewer MUs were needed and QA results were more robust for Algorithm 2, which more highly modulated dose rate.« less

Qualitative and quantitative analyses of flavonoids in Spirodela polyrrhiza by high-performance liquid chromatography coupled with mass spectrometry.

PubMed

Qiao, Xue; He, Wen-ni; Xiang, Cheng; Han, Jian; Wu, Li-jun; Guo, De-an; Ye, Min

2011-01-01

Spirodela polyrrhiza (L.) Schleid. is a traditional Chinese herbal medicine for the treatment of influenza. Despite its wide use in Chinese medicine, no report on quality control of this herb is available so far. To establish qualitative and quantitative analytical methods by high-performance liquid chromatography (HPLC) coupled with mass spectrometry (MS) for the quality control of S. polyrrhiza. The methanol extract of S. polyrrhiza was analysed by HPLC/ESI-MS(n). Flavonoids were identified by comparing with reference standards or according to their MS(n) (n = 2-4) fragmentation behaviours. Based on LC/MS data, a standardised HPLC fingerprint was established by analysing 15 batches of commercial herbal samples. Furthermore, quantitative analysis was conducted by determining five major flavonoids, namely luteolin 8-C-glucoside, apigenin 8-C-glucoside, luteolin 7-O-glucoside, apigenin 7-O-glucoside and luteolin. A total of 18 flavonoids were identified by LC/MS, and 14 of them were reported from this herb for the first time. The HPLC fingerprints contained 10 common peaks, and could differentiate good quality batches from counterfeits. The total contents of five major flavonoids in S. polyrrhiza varied significantly from 4.28 to 19.87 mg/g. Qualitative LC/MS and quantitative HPLC analytical methods were established for the comprehensive quality control of S. polyrrhiza. Copyright © 2011 John Wiley & Sons, Ltd.

Effect of Liberibacter infection (huanglongbing or "greening" disease) of citrus on orange juice flavor quality by sensory evaluation.

PubMed

Plotto, Anne; Baldwin, Elizabeth; McCollum, Greg; Manthey, John; Narciso, Jan; Irey, Mike

2010-05-01

Some anecdotal reports suggest that infection of citrus trees with Candidatus Liberibacter asiaticus (Las), the suspected causal agent of huanglongbing (HLB) disease, imparts off flavor to orange juice. It is of interest to the industry to know how Las infection affects juice quality with respect to cultivar, maturity, or processing method. Hamlin, Midsweet, and Valencia oranges were harvested over 2 y from trees that tested negative (Las-) or positive (Las+) for Las from different groves and included normal looking (nonsymptomatic) and symptomatic fruit (small, green, and lopsided) from Las+ trees. In the 1st year, fruit were manually juiced, while in the 2nd year, a commercial process was used. Juice from Las+ trees was compared to juice from Las- trees in difference-from-control tests, and by descriptive analysis. Results showed large variability due to tree, harvest date, and cultivar. Juice from Hamlin Las+ trees tended to be more bitter and sour than its Las- counterpart. In contrast, hand processed Valencia juice from Las+ trees was perceived to have some off-flavor and bitterness compared to control, but the following year, commercially processed Valencia juice from Las+ trees was perceived to be only slightly more sour than juice from Las- trees for the April harvest, and to be sweeter for the June harvest. When juice from individual replicates was pooled to be more representative of a commercial situation, there was no difference between Las+ and Las- juice in Valencia. Trained panel differences were noted for juice from Hamlin Las+ fruit, especially for symptomatic fruit. Assumptions that juice made from oranges harvested from Huanglongbing (from infection with Liberibacter sp.) affected trees is off-flavored appeared to be generally more true for Hamlin juice than for Midsweet or Valencia, especially for Hamlin juice made from symptomatic fruit. For Midsweet and Valencia, flavor differences between juice made from fruit harvested from diseased or healthy trees varied greatly between trees, season, and even processing method. Under a commercial processing situation, where juice is blended from several varieties, seasons, and multiple locations, it is expected that off-flavor will not be a major problem.

Testing an egg yolk supplemented diet on boars to aid in sperm adaptation at 5°C.

PubMed

Casas, Isabel; Miller-Lux, Yvonne; Osborne, Betty; Bonet, Sergi; Althouse, Gary C

2015-01-01

In many species, extended semen can be stored at low temperatures to slow bacterial growth. However, boar semen performs poorly at temperatures below 15 °C and this poses unique challenges, as it is not easy to maintain a constant 15-19 °C during shipment. Some extenders have been formulated with egg yolk for storage at 5 °C but the addition of egg yolk is not applicable in the majority of commercial operations. The purpose of this study was to evaluate if boar dietary supplementation with powdered egg yolk imparts any protective effects on sperm quality when stored at 15 °C and 5 °C for up to 11 days in a conventional extender. Ten boars were fed a commercial diet with the addition of 0.11 Kg of powdered egg yolk for 10 weeks. Ejaculates collected on weeks 4, 6, 8, and 10 were processed for storage at both 15 °C and 5 °C and compared with ejaculates from boars fed a standard diet. Throughout an 11-day storage period, sperm quality was assessed including several motility and morphologic parameters and select plasma membrane properties (fluidity, integrity, and triacylglycerol content). Linear regression models were used to describe effects of treatment, storage day, week and temperature on all sperm parameters. Overall, there were minimal beneficial effects of egg yolk treatment on sperm quality parameters. Sperm from egg yolk supplemented boars did have a slower decline in viability and plasma membrane fluidity than that observed in the control sperm when stored at 5 °C (p < 0.001). Additionally, there was an increase in total morphologic abnormalities in sperm from egg yolk fed boars compared to controls at week 10 (p <  .001). In conclusion, the results of this study do not support a significant benefit to sperm quality or resistance to cold storage when feeding a 10-week dietary supplementation of 0.11 Kg powdered egg yolk to crossbred boars.

Flat-plate solar array project: Experimental process system development unit for producing semiconductor-grade silicon using the silane-to-silicon process

NASA Technical Reports Server (NTRS)

1983-01-01

The process technology for the manufacture of semiconductor-grade silicon in a large commercial plant by 1986, at a price less than $14 per kilogram of silicon based on 1975 dollars is discussed. The engineering design, installation, checkout, and operation of an Experimental Process System Development unit was discussed. Quality control of scaling-up the process and an economic analysis of product and production costs are discussed.

Fluorescent and high intensity discharge lamp use in chambers and greenhouses

NASA Technical Reports Server (NTRS)

Langhans, Robert W.

1994-01-01

Fluorescent and High Intensity Discharge lamps have opened up great opportunities for researchers to study plant growth under controlled environment conditions and for commercial growers to increase plant production during low/light periods. Specific technical qualities of fluorescent and HID lamps have been critically reviewed. I will direct my remarks to fluorescent and high intensity discharge (HID) lamps in growth chambers, growth rooms, and greenhouses. I will discuss the advantages and disadvantages of using each lamp in growth chambers, growth rooms and greenhouses.

Commercial Television Personnel's Review of the Technical Quality and Marketability of AEL's "Around the Bend" Pilot Tapes. Technical Report No. 29.

ERIC Educational Resources Information Center

Shively, Joe E.

In order to determine whether Appalachia Educational Laboratory (AEL) had the capacity to produce a TV series of sufficient quality, two pilot tapes were produced by AEL and then submitted for rating to nine broadcasting specialists from several commercial TV stations. Based on the responses of these nine individuals to a questionnaire dealing…

Cluster 1: commercializing additive manufacturing—hurdles in materials characterization and testing

DOE PAGES

Roach, R. A.; Gardner, S. H.

2017-10-20

A major challenge in the commercialization of additive manufactured (AM) materials and processes is the ability to achieve acceptance of processes and products. There has been some progress towards acceptance has been made by adapting legacy qualification paradigms to match with the very limited process control and monitoring offered by AM machines. The opportunity for in-situ measurement can provide process monitoring and control perhaps changing the way we qualify parts however it is limited by lack of adequate process measurement methods. New measurement techniques, sensors and correlations to relevant phenomena are needed that enable process control and monitoring for consistentlymore » producing high quality articles. Beyond process data we need to characterize uncertainties of performance in all aspects of material, process and final part. These are prerequisites to achieving articles that are indeed worthy of materials characterization efforts that establish a microstructural reference of desirable performance through process-structure-property relations. Only then can industry apply physics based understanding of the material, part and process to probabilistically predict performance of an AM part. Our paper provides a brief overview, discussion of hurdles and key areas where R&D investment is needed.« less

Cluster 1: commercializing additive manufacturing—hurdles in materials characterization and testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roach, R. A.; Gardner, S. H.

A major challenge in the commercialization of additive manufactured (AM) materials and processes is the ability to achieve acceptance of processes and products. There has been some progress towards acceptance has been made by adapting legacy qualification paradigms to match with the very limited process control and monitoring offered by AM machines. The opportunity for in-situ measurement can provide process monitoring and control perhaps changing the way we qualify parts however it is limited by lack of adequate process measurement methods. New measurement techniques, sensors and correlations to relevant phenomena are needed that enable process control and monitoring for consistentlymore » producing high quality articles. Beyond process data we need to characterize uncertainties of performance in all aspects of material, process and final part. These are prerequisites to achieving articles that are indeed worthy of materials characterization efforts that establish a microstructural reference of desirable performance through process-structure-property relations. Only then can industry apply physics based understanding of the material, part and process to probabilistically predict performance of an AM part. Our paper provides a brief overview, discussion of hurdles and key areas where R&D investment is needed.« less

Commercial breakfast cereals available in Mexican markets and their contribution in dietary fiber, β-glucans and protein quality by rat bioassays.

PubMed

Falcón-Villa, María R; Barrón-Hoyos, Jesús M; Cinco-Moroyoqui, Francisco J

2014-09-01

The beneficial effect of dietary fiber (DF) consumption has long been recognized. The global economy and open market trade policies have increased the availability of food products in Mexican markets, resulting in a wide variety of ready-to-eat commercial breakfast cereals classified as 'high fiber'. This research was aimed to evaluate the total dietary fiber contents, its fractions (soluble and insoluble) and β-glucan in 13 commercial 'high-fiber' breakfast cereals, as well as to evaluate their protein quality by rat bioassays. Commercial 'high-fiber' breakfast cereals had 7.42-39.82% insoluble dietary fiber, 2.53-12.85% soluble dietary fiber, and 0.45-4.96% β-glucan. These ready-to-eat commercial 'high-fiber' breakfast cereals differed significantly in their total dietary fiber, their soluble and insoluble DF fractions, and also in their β-glucan contents. When supplied as experimental diets, in 14-day rat feeding trials, the 'high-fiber' breakfast cereals showed an adverse effect on the % N digestibility but protein utilization, as measured as net protein ratio (NPR), was not significantly affected. The consumption of these commercial breakfast cereals, especially those made of oats as the basic ingredient, is highly recommended, since these products, being a concentrated source of dietary fiber, do not affect their protein quality.

A comparative study of noise pollution levels in some selected areas in Ilorin Metropolis, Nigeria.

PubMed

Oyedepo, Olayinka S; Saadu, Abdullahi A

2009-11-01

The noise pollution is a major problem for the quality of life in urban areas. This study was conducted to compare the noise pollution levels at busy roads/road junctions, passengers loading parks, commercial, industrial and residential areas in Ilorin metropolis. A total number of 47-locations were selected within the metropolis. Statistical analysis shows significant difference (P < 0.05) in noise pollution levels between industrial areas and low density residential areas, industrial areas and high density areas, industrial areas and passengers loading parks, industrial areas and commercial areas, busy roads/road junctions and low density areas, passengers loading parks and commercial areas and commercial areas and low density areas. There is no significant difference (P > 0.05) in noise pollution levels between industrial areas and busy roads/road junctions, busy roads/road junctions and high density areas, busy roads/road junctions and passengers loading parks, busy roads/road junctions and commercial areas, passengers loading parks and high density areas, passengers loading parks and commercial areas and commercial areas and high density areas. The results show that Industrial areas have the highest noise pollution levels (110.2 dB(A)) followed by busy roads/Road junctions (91.5 dB(A)), Passengers loading parks (87.8 dB(A)) and Commercial areas (84.4 dB(A)). The noise pollution levels in Ilorin metropolis exceeded the recommended level by WHO at 34 of 47 measuring points. It can be concluded that the city is environmentally noise polluted and road traffic and industrial machineries are the major sources of it. Noting the noise emission standards, technical control measures, planning and promoting the citizens awareness about the high noise risk may help to relieve the noise problem in the metropolis.

Automatic loudness control in short-form content for broadcasting.

PubMed

Pires, Leandro da S; Vieira, Maurílio N; Yehia, Hani C

2017-03-01

During the early years of the International Telecommunication Union (ITU) loudness calculation standard for sound broadcasting [ITU-R (2006), Rec. BS Series, 1770], the need for additional loudness descriptors to evaluate short-form content, such as commercials and live inserts, was identified. This work proposes a loudness control scheme to prevent loudness jumps, which can bother audiences. It employs short-form content audio detection and dynamic range processing methods for the maximum loudness level criteria. Detection is achieved by combining principal component analysis for dimensionality reduction and support vector machines for binary classification. Subsequent processing is based on short-term loudness integrators and Hilbert transformers. The performance was assessed using quality classification metrics and demonstrated through a loudness control example.

Nintendo Wii™ Versus Xbox Kinect™ for Assisting People With Parkinson's Disease.

PubMed

Alves, Melissa L M; Mesquita, Beatriz S; Morais, Wenderson S; Leal, Josevan C; Satler, Corina E; Dos Santos Mendes, Felipe A

2018-06-01

This study investigated changes in motor and cognitive skills, anxiety levels, and quality of life perception among patients with Parkinson's Disease (PD) following training with different commercial gaming devices-Nintendo Wii™ and Xbox Kinect™. We used a quasi-experimental, simple blinded clinical trial, dividing 27 patients with PD into three equal groups of nine members: (a) Nintendo Wii™, (b) Xbox Kinect™, and (c) control group. After pretests, experimental group participants spent 10 sessions playing four games of the selected gaming device, while control group participants received no intervention. Only those engaged with the Nintendo Wii™ significantly improved their performance on single and dual task gait tests, decreased anxiety levels, and improved memory, attention, and reversibility. The control group showed no changes on any measures.

Precise Morphology Control and Continuous Fabrication of Perovskite Solar Cells Using Droplet-Controllable Electrospray Coating System.

PubMed

Hong, Seung Chan; Lee, Gunhee; Ha, Kyungyeon; Yoon, Jungjin; Ahn, Namyoung; Cho, Woohyung; Park, Mincheol; Choi, Mansoo

2017-03-08

Herein, we developed a novel electrospray coating system for continuous fabrication of perovskite solar cells with high performance. Our system can systemically control the size of CH 3 NH 3 PbI 3 precursor droplets by modulating the applied electrical potential, shown to be a crucial factor for the formation of perovskite films. As a result, we have obtained pinhole-free and large grain-sized perovskite solar cells, yielding the best PCE of 13.27% with little photocurrent hysteresis. Furthermore, the average PCE through the continuous coating process was 11.56 ± 0.52%. Our system demonstrates not only the high reproducibility but also a new way to commercialize high-quality perovskite solar cells.

Carcass Characteristics and Meat Quality of Korean Native Ducks and Commercial Meat-type Ducks Raised under Same Feeding and Rearing Conditions

PubMed Central

Kwon, H. J.; Choo, Y. K.; Choi, Y. I.; Kim, E. J.; Kim, H. K.; Heo, K. N.; Choi, H. C.; Lee, S. K.; Kim, C. J.; Kim, B. G.; Kang, C. W.; An, B. K.

2014-01-01

This study was conducted to compare carcass characteristics and physico-chemical meat quality in two different genotype ducks raised under identical feeding and rearing conditions. A total of ninety 1-d-old Korean native ducks (KND, n = 45) and commercial meat-type ducks (Grimaud, n = 45) were fed same experimental diets during 56 d and 42 d, respectively to obtain similar slaughter weights. The experimental diet for starter period contained 20% crude protein (CP) and 2,900 kcal nitrogen corrected true metabolizable energy (TMEn)/kg of diet and that for grower period contained 17% CP and 3,050 TMEn/kg of diet. Average daily gain and feed efficiency of KND were inferior to those of commercial meat-type ducks (p<0.05). Carcass weight was not different between two genetically different ducks, but carcass yield of KND was significantly higher (p<0.05) than that of commercial meat-type ducks. There were no significant differences in cooking loss and pH of breast meat between two genetically different ducks, but water holding capacity of KND was significantly higher than that of commercial meat-type ducks. The linoleic acid and total polyunsaturated fatty acid of breast meat from KND were significantly higher (p<0.05) than the corresponding part from commercial meat-type ducks. Significant differences were detected in water holding capacity and the content of linoleic acid and polyunsaturated fatty acid, which were significantly higher in KND, whereas growth performance tended to be superior in commercial ducks. At the market weight, the meat from KND was judged to have better qualities with regard to higher water holding capacity and greater content of polyunsaturated fatty acid compare with meat from commercial meat-type duck. PMID:25358325

Carcass Characteristics and Meat Quality of Korean Native Ducks and Commercial Meat-type Ducks Raised under Same Feeding and Rearing Conditions.

PubMed

Kwon, H J; Choo, Y K; Choi, Y I; Kim, E J; Kim, H K; Heo, K N; Choi, H C; Lee, S K; Kim, C J; Kim, B G; Kang, C W; An, B K

2014-11-01

This study was conducted to compare carcass characteristics and physico-chemical meat quality in two different genotype ducks raised under identical feeding and rearing conditions. A total of ninety 1-d-old Korean native ducks (KND, n = 45) and commercial meat-type ducks (Grimaud, n = 45) were fed same experimental diets during 56 d and 42 d, respectively to obtain similar slaughter weights. The experimental diet for starter period contained 20% crude protein (CP) and 2,900 kcal nitrogen corrected true metabolizable energy (TMEn)/kg of diet and that for grower period contained 17% CP and 3,050 TMEn/kg of diet. Average daily gain and feed efficiency of KND were inferior to those of commercial meat-type ducks (p<0.05). Carcass weight was not different between two genetically different ducks, but carcass yield of KND was significantly higher (p<0.05) than that of commercial meat-type ducks. There were no significant differences in cooking loss and pH of breast meat between two genetically different ducks, but water holding capacity of KND was significantly higher than that of commercial meat-type ducks. The linoleic acid and total polyunsaturated fatty acid of breast meat from KND were significantly higher (p<0.05) than the corresponding part from commercial meat-type ducks. Significant differences were detected in water holding capacity and the content of linoleic acid and polyunsaturated fatty acid, which were significantly higher in KND, whereas growth performance tended to be superior in commercial ducks. At the market weight, the meat from KND was judged to have better qualities with regard to higher water holding capacity and greater content of polyunsaturated fatty acid compare with meat from commercial meat-type duck.

Effect of a hypocaloric diet with a commercial formula in weight loss and quality of life in obese patients with chronic osteoarthritis.

PubMed

de Luis, D A; Izaola, O; García Alonso, M; Aller, R; Cabezas, G; de la Fuente, B

2012-01-01

The aim of our study was to evaluate in patients with obesity and chronic osteoarthritis the impact on quality of life and metabolic control of a dietary intervention with a hypocaloric commercial formula. A sample of 55 obese patients with chronic osteoarthritis was enrolled. The study consisted of a 12-week weight reduction program where the participants received an oral diet replaced with 2 bricks of Optisource Plus®. In order to assess the effect of weight loss on different parameters, patients were divided in two groups by the median of weight loss percentage (9%); group 1 (< 9%) and group 2 (> 9%). In group 2, patients showed an improvement in total SF-36 score (4.0 ± 6.1 points), physical function domain of SF 36 (1.8 ± 3.4 points), role physical domain of SF 36 (0.6 ± 1.6 points) and vitality domain of SF 36 (2.7 ± 4.6 points) improved. Total score of WOMAC test (- 8.2 ± 15.0 points), function domain of WOMAC test (- 6.5 ± 10.6 points) and stiffness domain of WOMAC test (-0.7 ± 2.1 points) improved, too. The effect on metabolic response, functionality and quality of life was better in patients with a percentage of weight loss > 9% than patients with a lower weight loss.

Manufacturing of biodrugs: need for harmonization in regulatory standards.

PubMed

Sahoo, Niharika; Choudhury, Koel; Manchikanti, Padmavati

2009-01-01

Biodrugs (biologics) are much more complex than chemically synthesized drugs because of their structural heterogeneity and interactions within a given biologic system. The manufacturing process in the biodrug industry varies with each type of molecule and is far more elaborate and stringent due to the use of living organisms and complex substrates. Product purity and altered structural characteristics leading to potential immunogenicity have often been of concern when establishing quality and safety in the use of biodrugs. Regulatory compliance in manufacturing and commercialization of biodrugs involves quality control, quality assurance, and batch documentation. Many factors such as host cell development, cell bank establishment, cell culture, protein production, purification, analysis, formulation, storage, and handling are critical for ensuring the purity, activity, and safety of the finished product. Good Manufacturing Practice (GMP) for biodrugs has been developed in certain regions such as the EU, US, and Japan. Due to differences in manufacturing methods and systems, product-specific GMP guidelines are evolving. In general, there are variations in GMP guidelines between countries, which lead to difficulty for the manufacturers in conforming to different standards, thus entailing delays in the commercialization of biodrugs. There is a need to develop a unified regulatory guideline for biodrug manufacturing across various countries, which would be helpful in the marketing of products and trade. This review deals with the comparative framework and analysis of GMP regulation of biodrugs.

From Banking to International Governance: Fostering Innovation in Stem Cell Research

PubMed Central

Isasi, Rosario; Knoppers, Bartha M.

2011-01-01

Stem cell banks are increasingly recognized as an essential resource of biological materials for both basic and translational stem cell research. By providing transnational access to quality controlled and ethically sourced stem cell lines, stem cell banks seek to foster international collaboration and innovation. However, given that national stem cell banks operate under different policy, regulatory and commercial frameworks, the transnational sharing of stem cell materials and data can be complicating. This paper will provide an overview of the most pressing challenges regarding the governance of stem cell banks, and the difficulties in designing regulatory and commercial frameworks that foster stem cell research. Moreover, the paper will shed light on the numerous international initiatives that have arisen to help harmonize and standardize stem cell banking and research processes to overcome such challenges. PMID:21904557

Dollars and scents: commercial opportunities in olfaction and taste.

PubMed

Gilbert, Avery N; Firestein, Stuart

2002-11-01

Research successes over the past decade have provided a broad outline of the neuroscience of olfaction and taste. Our understanding of these systems now spans the molecular to the psychological. It will soon reach critical mass and begin to generate a variety of practical applications with commercial potential. Given the ubiquity of smell and taste and their importance to health, nutrition and quality of life, these applications could have a major impact on consumer product markets and create entirely new ones. Sensory biotechnology could be the first post-genomic application to break through to the consumer market. We describe odor modulation technologies with implications for food intake, health care and other arenas. Our deeper understanding of olfaction and taste in animal behavior and reproduction provides opportunities in pest control and animal husbandry, where environmentally neutral interventions are much in demand.

Test progress on the electrostatic membrane reflector

NASA Technical Reports Server (NTRS)

Mihora, D. J.

1981-01-01

An extemely lightweight type of precision reflector antenna, being developed for potential deployment from the space shuttle, uses electrostatic forces to tension a thin membrane and form it into a concave reflector surface. The typical shuttle-deployed antenna would have a diameter of 100 meters and an RMS surface smoothness of 10 to 1 mm for operation at 1 to 10 GHz. NASA Langley Research Center built and is currently testing a subscale (16 foot diameter) model of the membrane reflector portion of such an antenna. Preliminary test results and principal factors affecting surface quality are addressed. Factors included are the effect of the perimeter boundary, splicing of the membrane, the long-scale smoothness of commercial membranes, and the spatial controllability of the membrane using voltage adjustments to alter the electrostatic pressure. Only readily available commercial membranes are considered.

Application of sigma metrics for the assessment of quality control in clinical chemistry laboratory in Ghana: A pilot study.

PubMed

Afrifa, Justice; Gyekye, Seth A; Owiredu, William K B A; Ephraim, Richard K D; Essien-Baidoo, Samuel; Amoah, Samuel; Simpong, David L; Arthur, Aaron R

2015-01-01

Sigma metrics provide a uniquely defined scale with which we can assess the performance of a laboratory. The objective of this study was to assess the internal quality control (QC) in the clinical chemistry laboratory of the University of Cape Cost Hospital (UCC) using the six sigma metrics application. We used commercial control serum [normal (L1) and pathological (L2)] for validation of quality control. Metabolites (glucose, urea, and creatinine), lipids [triglycerides (TG), total cholesterol, high-density lipoprotein cholesterol (HDL-C)], enzymes [alkaline phosphatase (ALP), alanine aminotransferase (AST)], electrolytes (sodium, potassium, chloride) and total protein were assessed. Between-day imprecision (CVs), inaccuracy (Bias) and sigma values were calculated for each control level. Apart from sodium (2.40%, 3.83%), chloride (2.52% and 2.51%) for both L1 and L2 respectively, and glucose (4.82%), cholesterol (4.86%) for L2, CVs for all other parameters (both L1 and L2) were >5%. Four parameters (HDL-C, urea, creatinine and potassium) achieved sigma levels >1 for both controls. Chloride and sodium achieved sigma levels >1 for L1 but <1 for L2. In contrast, cholesterol, total protein and AST achieved sigma levels <1 for L1 but >1 for L2. Glucose and ALP achieved a sigma level >1 for both control levels whereas TG achieved a sigma level >2 for both control levels. Unsatisfactory sigma levels (<3) where achieved for all parameters using both control levels, this shows instability and low consistency of results. There is the need for detailed assessment of the analytical procedures and the strengthening of the laboratory control systems in order to achieve effective six sigma levels for the laboratory.

Application of sigma metrics for the assessment of quality control in clinical chemistry laboratory in Ghana: A pilot study

PubMed Central

Afrifa, Justice; Gyekye, Seth A.; Owiredu, William K. B. A.; Ephraim, Richard K. D.; Essien-Baidoo, Samuel; Amoah, Samuel; Simpong, David L.; Arthur, Aaron R.

2015-01-01

Background: Sigma metrics provide a uniquely defined scale with which we can assess the performance of a laboratory. The objective of this study was to assess the internal quality control (QC) in the clinical chemistry laboratory of the University of Cape Cost Hospital (UCC) using the six sigma metrics application. Materials and Methods: We used commercial control serum [normal (L1) and pathological (L2)] for validation of quality control. Metabolites (glucose, urea, and creatinine), lipids [triglycerides (TG), total cholesterol, high-density lipoprotein cholesterol (HDL-C)], enzymes [alkaline phosphatase (ALP), alanine aminotransferase (AST)], electrolytes (sodium, potassium, chloride) and total protein were assessed. Between-day imprecision (CVs), inaccuracy (Bias) and sigma values were calculated for each control level. Results: Apart from sodium (2.40%, 3.83%), chloride (2.52% and 2.51%) for both L1 and L2 respectively, and glucose (4.82%), cholesterol (4.86%) for L2, CVs for all other parameters (both L1 and L2) were >5%. Four parameters (HDL-C, urea, creatinine and potassium) achieved sigma levels >1 for both controls. Chloride and sodium achieved sigma levels >1 for L1 but <1 for L2. In contrast, cholesterol, total protein and AST achieved sigma levels <1 for L1 but >1 for L2. Glucose and ALP achieved a sigma level >1 for both control levels whereas TG achieved a sigma level >2 for both control levels. Conclusion: Unsatisfactory sigma levels (<3) where achieved for all parameters using both control levels, this shows instability and low consistency of results. There is the need for detailed assessment of the analytical procedures and the strengthening of the laboratory control systems in order to achieve effective six sigma levels for the laboratory. PMID:25657495

Water reuse systems: A review of the principal components

USGS Publications Warehouse

Lucchetti, G.; Gray, G.A.

1988-01-01

Principal components of water reuse systems include ammonia removal, disease control, temperature control, aeration, and particulate filtration. Effective ammonia removal techniques include air stripping, ion exchange, and biofiltration. Selection of a particular technique largely depends on site-specific requirements (e.g., space, existing water quality, and fish densities). Disease control, although often overlooked, is a major problem in reuse systems. Pathogens can be controlled most effectively with ultraviolet radiation, ozone, or chlorine. Simple and inexpensive methods are available to increase oxygen concentration and eliminate gas supersaturation, these include commercial aerators, air injectors, and packed columns. Temperature control is a major advantage of reuse systems, but the equipment required can be expensive, particularly if water temperature must be rigidly controlled and ambient air temperature fluctuates. Filtration can be readily accomplished with a hydrocyclone or sand filter that increases overall system efficiency. Based on criteria of adaptability, efficiency, and reasonable cost, we recommend components for a small water reuse system.

Implementation of buffy-coat-derived pooled platelet concentrates for internal quality control of light transmission aggregometry: a proof of concept study.

PubMed

Prüller, F; Rosskopf, K; Mangge, H; Mahla, E; von Lewinski, D; Weiss, E C; Riegler, A; Enko, D

2017-12-01

Essentials In platelet function testing, standardized internal controls (IQC) are not commercially provided. Platelet function testing was performed daily on aliquoted pooled platelet concentrates. Pooled platelet concentrates showed stability for control purposes from Monday to Friday. Pooled platelet concentrates provide the necessary steadiness to serve as IQC material. Background Standardized commercially available control material for internal quality control (IQC) of light transmission aggregometry (LTA) is still lacking. Moreover, the availability of normal blood donors to provide fresh platelets is difficult in small laboratories, where 'volunteers' may be in short supply. Objectives To evaluate the implementation of buffy-coat-derived pooled platelet concentrates (PCs) for IQC material for LTA. Methods We used buffy-coat-derived pooled PCs from the blood bank as IQC material for LTA. On each weekend one PC was prepared (> 200 mL) and aliquoted from the original storage bag on a daily basis in four baby bags (40-50 mL), which were delivered from Monday to Friday to our laboratory. The IQC measurements of at least 85 work-weeks (from Monday to Friday) were evaluated with this new IQC material. LTA was performed on a four-channel Chronolog 700 Aggregometer (Chronolog Corporation, Havertown, PA, USA) (agonists: collagen, adenosine diphosphate [ADP], arachidonic acid [AA] and thrombin receptor activator peptide-6 [TRAP-6]). Results The medians of platelet aggregation from IQC measurements with collagen, ADP and AA from Monday to Friday were 68.0-59.5, 3.0-2.0 and 51.0-50.0%, respectively, and the mean of platelet aggregation with TRAP-6 was 71.2-66.4%. Conclusions Buffy-coat-derived pooled PCs serve as a reliable and robust IQC material for LTA measurements and would be beneficial for the whole laboratory procedure and employees' safety. © 2017 International Society on Thrombosis and Haemostasis.

Wavefront sensorless adaptive optics optical coherence tomography for in vivo retinal imaging in mice

PubMed Central

Jian, Yifan; Xu, Jing; Gradowski, Martin A.; Bonora, Stefano; Zawadzki, Robert J.; Sarunic, Marinko V.

2014-01-01

We present wavefront sensorless adaptive optics (WSAO) Fourier domain optical coherence tomography (FD-OCT) for in vivo small animal retinal imaging. WSAO is attractive especially for mouse retinal imaging because it simplifies optical design and eliminates the need for wavefront sensing, which is difficult in the small animal eye. GPU accelerated processing of the OCT data permitted real-time extraction of image quality metrics (intensity) for arbitrarily selected retinal layers to be optimized. Modal control of a commercially available segmented deformable mirror (IrisAO Inc.) provided rapid convergence using a sequential search algorithm. Image quality improvements with WSAO OCT are presented for both pigmented and albino mouse retinal data, acquired in vivo. PMID:24575347

Transglycosylation of stevioside to improve the edulcorant quality by lower substitution using cornstarch hydrolyzate and CGTase.

PubMed

Li, Sha; Li, Wei; Xiao, Qiu-yan; Xia, Yongmei

2013-06-01

Stevioside is an abundant sweetener extracted from Stevia rebaudiana leaf with a bitter aftertaste. Enzymatic transglycosylation of stevioside is a solution to improve the edulcorant quality of stevioside, but highly derivatised stevioside coming with high conversion of stevioside is undesired. In this experiment, the transglycosylation of stevioside was investigated by using a commercial cyclodextrin glucanotransferase and cornstarch hydrolyzate. With controlled parameters, the product was mainly composed of mono- and di-glucosylated stevioside while the highest stevioside conversion reached 77.11%. Neither kinetic nor thermodynamic factor stimulated the formation of high substituted steviosides. The simultaneous hydrolysis in the reaction might inhibit the yield of highly substituted steviosides. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of microencapsulated fat powders on rheological characteristics of biscuit dough and quality of biscuits.

PubMed

Sudha, M L; Chetana, R; Reddy, S Yella

2014-12-01

The effect of microencapsulated fat powders on the rheological characteristics and quality of biscuits were studied and compared with the control native fat normally used in the biscuit industry. Commercial bakery fat was encapsulated using sodium caseinate or skimmed milk powder (SMP) and the fat content in the powders was in the range of 73 - 78 % for sodium caseinate, whereas it ranged between 57.5 and 61 % with SMP and the sugar content was in the range of 9.8 - 17.5 %. The rheological characteristics indicated that with high sodium caseinate and SMP, the doughs were more elastic. The TPA analysis showed that with increasing the casein content in the fat powder, the dough hardness increased, and the doughs were less cohesive. The quality of biscuits was comparable with lower amount of encapsulating agents. Powders with lower amount of agents had comparable benefits on the rheological characteristics of the dough and biscuit quality.

Evaluating a preventive biological control agent applied on grapevines against Botrytis cinerea and its influence on winemaking.

PubMed

Escribano-Viana, Rocío; Portu, Javier; Garijo, Patrocinio; Gutiérrez, Ana Rosa; Santamaría, Pilar; López-Alfaro, Isabel; López, Rosa; González-Arenzana, Lucía

2018-02-25

This research was aimed to study the influence on grape and wine quality and on the fermentation processes of the application of a preventive biological treatment against Botrytis cinerea in Tempranillo Rioja grapevines. For this purpose, a biofungicide containing Bacillus subtilis QST713 was applied twice to the vineyard. Results were compared with non-treated samples from the same vineyard and with samples treated with a chemical fungicide composed of fenhexamid. Data showed that general grape quality and spontaneous alcoholic fermentation performance were not influenced by either fungicide application. The chemical fungicide had a considerable influence on the clonal diversity of Saccharomyces cerevisiae species, which led to the alcoholic fermentation. Furthermore, it caused longer malolactic fermentation than with the biological fungicide and in the control. The biofungicide made malolactic fermentation 1 day shorter because the establishment of the commercial lactic acid bacteria used as a starter culture was total. After malolactic fermentation, the wines did not show significant differences in general oenological parameters. Preventive biofungicide treatment against B. cinerea did not negatively influence the quality of grapes and wines and the fermentation processes. Therefore, biological control of B. cinerea with B. subtilis applied on grapevines could be advisable in oenological terms. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Reduction of patulin in apple cider by UV radiation.

PubMed

Dong, Qingfang; Manns, David C; Feng, Guoping; Yue, Tianli; Churey, John J; Worobo, Randy W

2010-01-01

The presence of the mycotoxin patulin in processed apple juice and cider presents a continual challenge to the food industry as both consumer health and product quality issues. Although several methods for control and/or elimination of patulin have been proposed, no unifying method has been commercially successful for reducing patulin burdens while maintaining product quality. In the present study, exposure to germicidal UV radiation was evaluated as a possible commercially viable alternative for the reduction and possible elimination of the patulin mycotoxin in fresh apple cider. UV exposure of 14.2 to 99.4 mJ/cm(2) resulted in a significant and nearly linear decrease in patulin levels while producing no quantifiable changes in the chemical composition (i.e., pH, Brix, and total acids) or organoleptic properties of the cider. For the range of UV doses tested, patulin levels decreased by 9.4 to 43.4%; the greatest reduction was achieved after less than 15 s of UV exposure. The method of UV radiation (the CiderSure 3500 system) is an easily implemented, high-throughput, and cost-effective method that offers simultaneous UV pasteurization of cider and juice products and reduction and/or elimination of patulin without unwanted alterations in the final product.

Light Quality Dependent Changes in Morphology, Antioxidant Capacity, and Volatile Production in Sweet Basil (Ocimum basilicum)

PubMed Central

Carvalho, Sofia D.; Schwieterman, Michael L.; Abrahan, Carolina E.; Colquhoun, Thomas A.; Folta, Kevin M.

2016-01-01

Narrow-bandwidth light treatments may be used to manipulate plant growth, development and metabolism. In this report LED-based light treatments were used to affect yield and metabolic content of sweet basil (Ocimum basilicum L. cv “Ceasar”) grown in controlled environments. This culinary herb produces an aroma highly appreciated by consumers, primarily composed of terpenes/terpenoids, phenylpropanoids, and fatty-acid- derived volatile molecules. Basil plants were grown under narrow-bandwidth light conditions, and leaf area, height, mass, antioxidant capacity and volatile emissions were measured at various time points. The results indicate reproducible significant differences in specific volatiles, and in biochemical classes of volatiles, compared to greenhouse grown plants. For example, basil plants grown under blue/red/yellow or blue/red/green wavelengths emit higher levels of a subset of monoterpenoid volatiles, while a blue/red/far-red treatment leads to higher levels of most sesquiterpenoid volatile molecules. Specific light treatments increase volatile content, mass, and antioxidant capacity. The results show that narrow-bandwidth illumination can induce discrete suites of volatile classes that affect sensory quality in commercial herbs, and may be a useful tool in improving commercial production. PMID:27635127

Light Quality Dependent Changes in Morphology, Antioxidant Capacity, and Volatile Production in Sweet Basil (Ocimum basilicum).

PubMed

Carvalho, Sofia D; Schwieterman, Michael L; Abrahan, Carolina E; Colquhoun, Thomas A; Folta, Kevin M

2016-01-01

Narrow-bandwidth light treatments may be used to manipulate plant growth, development and metabolism. In this report LED-based light treatments were used to affect yield and metabolic content of sweet basil (Ocimum basilicum L. cv "Ceasar") grown in controlled environments. This culinary herb produces an aroma highly appreciated by consumers, primarily composed of terpenes/terpenoids, phenylpropanoids, and fatty-acid- derived volatile molecules. Basil plants were grown under narrow-bandwidth light conditions, and leaf area, height, mass, antioxidant capacity and volatile emissions were measured at various time points. The results indicate reproducible significant differences in specific volatiles, and in biochemical classes of volatiles, compared to greenhouse grown plants. For example, basil plants grown under blue/red/yellow or blue/red/green wavelengths emit higher levels of a subset of monoterpenoid volatiles, while a blue/red/far-red treatment leads to higher levels of most sesquiterpenoid volatile molecules. Specific light treatments increase volatile content, mass, and antioxidant capacity. The results show that narrow-bandwidth illumination can induce discrete suites of volatile classes that affect sensory quality in commercial herbs, and may be a useful tool in improving commercial production.

Development of an Effective System Identification and Control Capability for Quad-copter UAVs

NASA Astrophysics Data System (ADS)

Wei, Wei

In recent years, with the promise of extensive commercial applications, the popularity of Unmanned Aerial Vehicles (UAVs) has dramatically increased as witnessed by publications and mushrooming research and educational programs. Over the years, multi-copter aircraft have been chosen as a viable configuration for small-scale VTOL UAVs in the form of quad-copters, hexa-copters and octo-copters. Compared to the single main rotor configuration such as the conventional helicopter, multi-copter airframes require a simpler feedback control system and fewer mechanical parts. These characteristics make these UAV platforms, such as quad-copter which is the main emphasis in this dissertation, a rugged and competitive candidate for many applications in both military and civil areas. Because of its configuration and relative size, the small-scale quad-copter UAV system is inherently very unstable. In order to develop an effective control system through simulation techniques, obtaining an accurate dynamic model of a given quad-copter is imperative. Moreover, given the anticipated stringent safety requirements, fault tolerance will be a crucial component of UAV certification. Accurate dynamic modeling and control of this class of UAV is an enabling technology and is imperative for future commercial applications. In this work, the dynamic model of a quad-copter system in hover flight was identified using frequency-domain system identification techniques. A new and unique experimental system, data acquisition and processing procedure was developed catering specifically to the class of electric powered multi-copter UAV systems. The Comprehensive Identification from FrEquency Responses (CIFER RTM) software package, developed by US Army Aviation Development Directorate -- AFDD, was utilized along with flight tests to develop dynamic models of the quad-copter system. A new set of flight tests were conducted and the predictive capability of the dynamic models were successfully validated. A PID controller and two fuzzy logic controllers were developed based on the validated dynamic models. The controller performances were evaluated and compared in both simulation environment and flight testing. Flight controllers were optimized to comply with US Aeronautical Design Standard Performance Specification Handling Quality Requirements for Military Rotorcraft (ADS-33E-PRF). Results showed a substantial improvement for developed controllers when compared to the nominal controllers based on hand tuning. The scope of this research involves experimental system hardware and software development, flight instrumentation, flight testing, dynamics modeling, system identification, dynamic model validation, control system modeling using PID and fuzzy logic, analysis of handling qualities, flight control optimization and validation. Both closed-loop and open-loop dynamics of the quad-copter system were analyzed. A cost-effective and high quality system identification procedure was applied and results proved in simulations as well as in flight tests.

Analysis of pollen load based on color, physicochemical composition and botanical source.

PubMed

Modro, Anna F H; Silva, Izabel C; Luz, Cynthia F P; Message, Dejair

2009-06-01

Pollen load samples from 10 hives of Apis mellifera (L.) were analyzed based on their physicochemical composition and botanical source, considering color as a parameter for quality control. In seven samples it was possible to establish the occurrence of more than 80% of a single pollen type, characterizing them as unifloral but with protein content variation. One of the samples was exclusively composed of saprophytic fungi (Cladosporium sp.). Comparing the mean results of the fungi loads with those of the nutritional components of pollen load, the former presented higher protein, mineral matter and dry matter and lower organic matter, ethereal extract and total carbohydrate values. The monochromatic samples met the physicochemical specifications regulating pollen load quality. The results showed that homogeneous coloration of the pollen load was not found to be a good indication of unifloral pollen, confirming the importance of physicochemical analysis and melissopalynological analysis for characterization of the quality of commercial pollen load.

Protein and hematological evaluations of infant formulated from cooking banana fruits (Musa spp, ABB genome) and fermented bambara groundnut (Vigna subterranean L. Verdc) seeds.

PubMed

Ijarotimi, Oluwole Steve

2008-01-01

Protein-energy malnutrition is regarded as one of the public health problems in developing countries as a result of poor feeding practices due to poverty. This study, therefore, aimed at evaluating nutritional quality of a potential weaning food formulated from locally available food materials. The cooking banana fruit (CB) and bambara groundnut seeds (BG) were purchased from local market in Akure, Ondo State, Nigeria. The CB and BG were processed into flours, mixed in ratios of 90:10, 80:20, 70:30 and 60:40 and subjected into proximate, sensory and biochemical analyses using standard procedures. Nutrend (a commercial formula) and ogi (corn gruel, a traditional weaning food) were used as control. The nutritient composition (g/100 g) of the food samples were ranged as follows: moisture 2.94-6.94, protein 7.02-16.0, ash 1.76-2.99, fat 0.76-8.45, fibre 1.52-3.75, carbohydrate 63.84-88.43 and energy 1569.8-1665.7 kcal. The biological value (BV), net protein retention (NPR), protein efficiency ratio (PER) and feed efficiency ratio (FER) of the experimental food samples were significantly (p<0.05) lower than nutrend, but higher than ogi. The haematological variables of rats fed with formulated food samples, commercial formula (nutrend) and traditional weaning food (ogi) were not significantly (p>0.05) influenced by the dietary treatment. However, the values obtained for red blood cell (RBC), white blood cell (WBC), pack cell volume (PCV) and erythrocyte sedimentation rate (ESR) were higher in the experimental food samples than the commercial food. The growth rate of animals fed with experimental food samples were lower than those fed with the nutrend, but higher than those fed with ogi. In conclusion, the nutritional quality of CB and fermented BG mix of 60:40 ratio was better than ogi; and comparable to the nutrend. This implies that it can be used to replace low quality traditional weaning food and the expensive commercial weaning formula.

Indoor Air Quality Building Education and Assessment Model Forms

EPA Pesticide Factsheets

The Indoor Air Quality Building Education and Assessment Model (I-BEAM) is a guidance tool designed for use by building professionals and others interested in indoor air quality in commercial buildings.

Characterizing commercial pureed foods: sensory, nutritional, and textural analysis.

PubMed

Ettinger, Laurel; Keller, Heather H; Duizer, Lisa M

2014-01-01

Dysphagia (swallowing impairment) is a common consequence of stroke and degenerative diseases such as Parkinson's and Alzheimer's. Limited research is available on pureed foods, specifically the qualities of commercial products. Because research has linked pureed foods, specifically in-house pureed products, to malnutrition due to inferior sensory and nutritional qualities, commercial purees also need to be investigated. Proprietary research on sensory attributes of commercial foods is available; however direct comparisons of commercial pureed foods have never been reported. Descriptive sensory analysis as well as nutritional and texture analysis of commercially pureed prepared products was performed using a trained descriptive analysis panel. The pureed foods tested included four brands of carrots, of turkey, and two of bread. Each commercial puree was analyzed for fat (Soxhlet), protein (Dumas), carbohydrate (proximate analysis), fiber (total fiber), and sodium content (Quantab titrator strips). The purees were also texturally compared with a line spread test and a back extrusion test. Differences were found in the purees for sensory attributes as well as nutritional and textural properties. Findings suggest that implementation of standards is required to reduce variability between products, specifically regarding the textural components of the products. This would ensure all commercial products available in Canada meet standards established as being considered safe for swallowing.

The Educational Efficacy of Distinct Information Delivery Systems in Modified Video Games

ERIC Educational Resources Information Center

Moshirnia, Andrew; Israel, Maya

2010-01-01

Despite the increasing popularity of many commercial video games, this popularity is not shared by educational video games. Modified video games, however, can bridge the gap in quality between commercial and education video games by embedding educational content into popular commercial video games. This study examined how different information…

In-School Commercialism: A Slick Compulsory Change Movement. Issues in Education.

ERIC Educational Resources Information Center

Flores, Stephanie A.

2001-01-01

Discusses the impact of commercialism on American public schools, arguing that commercialism imperils the democratic nature of public schools and compromises the goals of quality education for all children. Maintains that education's larger purposes diverge tremendously from those of the business community and that in-school advertising results in…

Quantifying the foodscape: A systematic review and meta-analysis of the validity of commercially available business data.

PubMed

Lebel, Alexandre; Daepp, Madeleine I G; Block, Jason P; Walker, Renée; Lalonde, Benoît; Kestens, Yan; Subramanian, S V

2017-01-01

This paper reviews studies of the validity of commercially available business (CAB) data on food establishments ("the foodscape"), offering a meta-analysis of characteristics associated with CAB quality and a case study evaluating the performance of commonly-used validity indicators describing the foodscape. Existing validation studies report a broad range in CAB data quality, although most studies conclude that CAB quality is "moderate" to "substantial". We conclude that current studies may underestimate the quality of CAB data. We recommend that future validation studies use density-adjusted and exposure measures to offer a more meaningful characterization of the relationship of data error with spatial exposure.

Quantifying the foodscape: A systematic review and meta-analysis of the validity of commercially available business data

PubMed Central

Lebel, Alexandre; Daepp, Madeleine I. G.; Block, Jason P.; Walker, Renée; Lalonde, Benoît; Kestens, Yan; Subramanian, S. V.

2017-01-01

This paper reviews studies of the validity of commercially available business (CAB) data on food establishments (“the foodscape”), offering a meta-analysis of characteristics associated with CAB quality and a case study evaluating the performance of commonly-used validity indicators describing the foodscape. Existing validation studies report a broad range in CAB data quality, although most studies conclude that CAB quality is “moderate” to “substantial”. We conclude that current studies may underestimate the quality of CAB data. We recommend that future validation studies use density-adjusted and exposure measures to offer a more meaningful characterization of the relationship of data error with spatial exposure. PMID:28358819

Thyme oil vapour and modified atmosphere packaging reduce anthracnose incidence and maintain fruit quality in avocado.

PubMed

Sellamuthu, Periyar Selvam; Mafune, Mpho; Sivakumar, Dharini; Soundy, Puffy

2013-09-01

Postharvest application of prochloraz fungicide is commercially practiced to control anthracnose, a postharvest disease in avocado. Increasing consumer concern regarding food safety and demand for organically produced fruits make it necessary to search for natural environmentally friendly alternative products and processes for the fruit industry. A combination of modified atmosphere packaging (MAP; ∼8% CO₂, 2% O₂) plus thyme oil (TO) was evaluated on the incidence and severity of anthracnose, physiological disorders (grey pulp, vascular browning), fruit quality parameters (L*, h°, firmness, weight loss) and sensory parameters (taste, texture, flavour and overall acceptance), phenylalanine ammonia-lyase (PAL) enzyme activity, total phenolic compounds, flavonoid contents and antioxidant activity in avocados ('Fuerte' and 'Hass' cultivars) held at 10 °C cold storage for 18 days and thereafter, ripened at 25 °C for 5-10 days. Stand-alone MAP, commercial treatment (prochloraz 0.05%) and untreated (control) fruit were included for comparison. MAP + TO treatment significantly (P < 0.05) reduced the incidence and severity of anthracnose, grey pulp, vascular browning, weight loss and loss of fruit firmness, and showed acceptable taste, flavour, texture and higher overall acceptance, increased PAL activity, total phenolic compounds, flavonoid contents and antioxidant activity, after ripening at 25 °C followed by cold storage at 10 °C. This investigation recommends MAP + TO combination treatment as a suitable alternative to the currently adopted prochloraz application. © 2013 Society of Chemical Industry.

[Commercial video games in the rehabilitation of patients with sub-acute stroke: a pilot study].

PubMed

Cano-Manas, M J; Collado-Vazquez, S; Cano-de-la-Cuerda, R

2017-10-16

Stroke generates dependence on the patients due to the various impairments associated. The use of low-cost technologies for neurological rehabilitation may be beneficial for the treatment of these patients. To determine whether combined treatment using a semi-immersive virtual reality protocol to an interdisciplinary rehabilitation approach, improve balance and postural control, functional independence, quality of life, motivation, self-esteem and adherence to intervention in stroke patients in subacute stage. A longitudinal prospective study with pre and post-intervention evaluation was carried out. Fourteen were recruited at La Fuenfria Hospital (Spain) and completed the intervention. Experimental intervention was performed during eight weeks in combination with conventional treatment of physiotherapy and occupational therapy. Each session was increased in time and intensity, using commercial video games linked to Xbox 360° videoconsole and Kinect sensor. There were statistical significant improvements in modified Rankin scale (p = 0.04), baropodometry (load distribution, p = 0.03; support surface, p = 0.01), Barthel Index (p = 0.01), EQ-5D Questionnaire (p = 0.01), motivation (p = 0.02), self-esteem (p = 0.01) and adherence to the intervention (p = 0.02). An interdisciplinary rehabilitation approach supplemented with semi-immersive virtual reality seems to be useful for improving balance and postural control, functional independence in basic activities of daily living, quality of life, as well as motivation and self-esteem, with excellent adherence. This intervention modality could be adopted as a therapeutic tool in neurological rehabilitation of stroke patients in subacute stage.

Response of Pink Lady® apples to post-harvest application of 1-methylcyclopropene as a function of applied dose, maturity at harvest, storage time and controlled atmosphere storage.

PubMed

Cocci, Emiliano; Sacchetti, Giampiero; Rocculi, Pietro; Dalla Rosa, Marco

2014-10-01

1-Methylcyclopropene (1-MCP) is an inhibitor of ethylene reception used in post-harvest treatments to delay fruit ripening. Several factors affect the efficacy of 1-MCP treatments. The effect of a post-harvest treatment with 1-MCP on the quality of Pink Lady® apples as a function of 1-MCP dose, storage time and maturity at harvest was investigated. 1-MCP treatment was further tested in combination with controlled atmosphere (CA) storage. 1-MCP limited fruit respiration and softening during storage and was more effective on partially matured fruits and at prolonged storage times. The delaying of 1-MCP on the increase of ripening index was greater on matured fruits at prolonged storage times. The combination of 1-MCP and CA treatments positively affected quality indices of mature apples during 6 months of storage and 7 days of commercial life, with 1-MCP being more effective than CA. 1-MCP and CA showed positive combined effects on firmness and ripening index after 6 months of storage, and on firmness and CO₂ production after a further 7 days of commercial life. By knowing fruit maturity at harvest and expected storage time it is possible to choose the most suitable 1-MCP dose to meet the market requirements by applying a simple polynomial model. © 2014 Society of Chemical Industry.

Application of carbon and hydrogen stable isotope analyses to detect exogenous citric acid in Japanese apricot liqueur.

PubMed

Akamatsu, Fumikazu; Oe, Takaaki; Hashiguchi, Tomokazu; Hisatsune, Yuri; Kawao, Takafumi; Fujii, Tsutomu

2017-08-01

Japanese apricot liqueur manufacturers are required to control the quality and authenticity of their liqueur products. Citric acid made from corn is the main acidulant used in commercial liqueurs. In this study, we conducted spiking experiments and carbon and hydrogen stable isotope analyses to detect exogenous citric acid used as an acidulant in Japanese apricot liqueurs. Our results showed that the δ 13 C values detected exogenous citric acid originating from C 4 plants but not from C 3 plants. The δ 2 H values of citric acid decreased as the amount of citric acid added increased, whether the citric acid originated from C 3 or C 4 plants. Commercial liqueurs with declared added acidulant provided higher δ 13 C values and lower δ 2 H values than did authentic liqueurs and commercial liqueurs with no declared added acidulant. Carbon and hydrogen stable isotope analyses are suitable as routine methods for detecting exogenous citric acid in Japanese apricot liqueur. Copyright © 2017 Elsevier Ltd. All rights reserved.

Surface attachment of active antimicrobial coatings onto conventional plastic-based laminates and performance assessment of these materials on the storage life of vacuum packaged beef sub-primals.

PubMed

Clarke, David; Tyuftin, Andrey A; Cruz-Romero, Malco C; Bolton, Declan; Fanning, Seamus; Pankaj, Shashi K; Bueno-Ferrer, Carmen; Cullen, Patrick J; Kerry, Joe P

2017-04-01

Two antimicrobial coatings, namely Sodium octanoate and Auranta FV (a commercial antimicrobial composed of bioflavonoids, citric, malic, lactic, and caprylic acids) were used. These two antimicrobials were surface coated onto the inner polyethylene layer of cold plasma treated polyamide films using beef gelatin as a carrier and coating polymer. This packaging material was then used to vacuum pack beef sub-primal cuts and stored at 4 °C. A control was prepared using the non-coated commercial laminate and the same vacuum packaged sub-primal beef cuts. During storage, microbial and quality assessments were carried out. Sodium octanoate treated packages significantly (p < 0.05) reduced microbial counts for all bacteria tested with an increase of 7 and 14 days, respectively compared to control samples. No significant effect on pH was observed with any treatment. The results suggested that these food grade antimicrobials have the potential to be used in antimicrobial active packaging applications for beef products. Copyright © 2016 Elsevier Ltd. All rights reserved.

Flavored Anesthetic Masks for Inhalational Induction in Children.

PubMed

Gupta, Aakriti; Mathew, Preethy Joseph; Bhardwaj, Neerja

2017-10-01

To evaluate the clinical efficacy of masking the odor of inhalational agents using fruit flavors on the anxiety behavior and compliance of children for inhalational induction. A prospective randomized double blind, placebo controlled study was conducted on 60 unpremedicated children in the age group of 4-12 y. Thirty children received anesthetic masks smeared with a flavor of child's choice while the other 30 children were induced using masks without flavor. Anxiety was assessed using modified Yale Pre-operative Anxiety Scale (mYPAS) in the pre-op room and during inhalational induction. Mask acceptance was graded by Induction Compliance Checklist (ICC). The cost-effectiveness of flavored anesthetic masks was compared to that of commercially available pre-scented masks. The baseline anxiety in the two groups was comparable. The number of children demonstrating high levels of anxiety at anesthetic induction was similar in flavored and non-flavored mask groups (p 0.45). The compliance to mask induction was also equally good (p 0.99). The authors found significant difference in the cost of flavored mask (INR 56.45 per mask) as compared to commercially available pre-scented masks (INR 660 per mask). The authors observed a placebo effect that reduced the pre-op anxiety in the control group which probably made the quality of induction equivalent with flavored and non-flavored masks. Therefore, using a flavored anesthetic mask is cost-effective than using a commercially available pre-scented mask.

Simple and rapid quality control of sulfated glycans by a fluorescence sensor assay--exemplarily developed for the sulfated polysaccharides from red algae Delesseria sanguinea.

PubMed

Lühn, Susanne; Grimm, Juliane C; Alban, Susanne

2014-04-10

Sulfated polysaccharides (SP) from algae are of great interest due to their manifold biological activities. Obstacles to commercial (especially medical) application include considerable variability and complex chemical composition making the analysis and the quality control challenging. The aim of this study was to evaluate a simple microplate assay for screening the quality of SP. It is based on the fluorescence intensity (FI) increase of the sensor molecule Polymer-H by SP and was originally developed for direct quantification of SP. Exemplarily, 65 SP batches isolated from the red alga Delesseria sanguinea (D.s.-SP) and several other algae polysaccharides were investigated. Their FI increase in the Polymer-H assay was compared with other analytical parameters. By testing just one concentration of a D.s.-SP sample, quality deviations from the reference D.s.-SP and thus both batch-to-batch variability and stability can be detected. Further, structurally distinct SP showed to differ in their concentration-dependent FI profiles. By using corresponding reference compounds, the Polymer-H assay is therefore applicable as identification assay with high negative predictability. In conclusion, the Polymer-H assay showed to represent not only a simple method for quantification, but also for characterization identification and differentiation of SP of marine origin.

Bioreactor process parameter screening utilizing a Plackett-Burman design for a model monoclonal antibody.

PubMed

Agarabi, Cyrus D; Schiel, John E; Lute, Scott C; Chavez, Brittany K; Boyne, Michael T; Brorson, Kurt A; Khan, Mansoora; Read, Erik K

2015-06-01

Consistent high-quality antibody yield is a key goal for cell culture bioprocessing. This endpoint is typically achieved in commercial settings through product and process engineering of bioreactor parameters during development. When the process is complex and not optimized, small changes in composition and control may yield a finished product of less desirable quality. Therefore, changes proposed to currently validated processes usually require justification and are reported to the US FDA for approval. Recently, design-of-experiments-based approaches have been explored to rapidly and efficiently achieve this goal of optimized yield with a better understanding of product and process variables that affect a product's critical quality attributes. Here, we present a laboratory-scale model culture where we apply a Plackett-Burman screening design to parallel cultures to study the main effects of 11 process variables. This exercise allowed us to determine the relative importance of these variables and identify the most important factors to be further optimized in order to control both desirable and undesirable glycan profiles. We found engineering changes relating to culture temperature and nonessential amino acid supplementation significantly impacted glycan profiles associated with fucosylation, β-galactosylation, and sialylation. All of these are important for monoclonal antibody product quality. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Human pathogens in marine mammal meat – a northern perspective.

PubMed

Tryland, M; Nesbakken, T; Robertson, L; Grahek-Ogden, D; Lunestad, B T

2014-09-01

Only a few countries worldwide hunt seals and whales commercially. In Norway, hooded and harp seals and minke whales are commercially harvested, and coastal seals (harbour and grey seals) are hunted as game. Marine mammal meat is sold to the public and thus included in general microbiological meat control regulations. Slaughtering and dressing of marine mammals are performed in the open air on deck, and many factors on board sealing or whaling vessels may affect meat quality, such as the ice used for cooling whale meat and the seawater used for cleaning, storage of whale meat in the open air until ambient temperature is reached, and the hygienic conditions of equipment, decks, and other surfaces. Based on existing reports, it appears that meat of seal and whale does not usually represent a microbiological hazard to consumers in Norway, because human disease has not been associated with consumption of such foods. However, as hygienic control on marine mammal meat is ad hoc, mainly based on spot-testing, and addresses very few human pathogens, this conclusion may be premature. Additionally, few data from surveys or systematic quality control screenings have been published. This review examines the occurrence of potential human pathogens in marine mammals, as well as critical points for contamination of meat during the slaughter, dressing, cooling, storage and processing of meat. Some zoonotic agents are of particular relevance as foodborne pathogens, such as Trichinella spp., Toxoplasma gondii, Salmonella and Leptospira spp. In addition, Mycoplasma spp. parapoxvirus and Mycobacterium spp. constitute occupational risks during handling of marine mammals and marine mammal products. Adequate training in hygienic procedures is necessary to minimize the risk of contamination on board, and acquiring further data is essential for obtaining a realistic assessment of the microbiological risk to humans from consuming marine mammal meat.

Indoor Air Quality Building Education and Assessment Model

EPA Pesticide Factsheets

The Indoor Air Quality Building Education and Assessment Model (I-BEAM), released in 2002, is a guidance tool designed for use by building professionals and others interested in indoor air quality in commercial buildings.

Links Related to the Indoor Air Quality Building Education and Assessment Model

EPA Pesticide Factsheets

The Indoor Air Quality Building Education and Assessment Model (I-BEAM) is a guidance tool designed for use by building professionals and others interested in indoor air quality in commercial buildings.

Bibliography for the Indoor Air Quality Building Education and Assessment Model

EPA Pesticide Factsheets

The Indoor Air Quality Building Education and Assessment Model (I-BEAM) is a guidance tool designed for use by building professionals and others interested in indoor air quality in commercial buildings.

Fuzzy comprehensive evaluation of multiple environmental factors for swine building assessment and control.

PubMed

Xie, Qiuju; Ni, Ji-Qin; Su, Zhongbin

2017-10-15

In confined swine buildings, temperature, humidity, and air quality are all important for animal health and productivity. However, the current swine building environmental control is only based on temperature; and evaluation and control methods based on multiple environmental factors are needed. In this paper, fuzzy comprehensive evaluation (FCE) theory was adopted for multi-factor assessment of environmental quality in two commercial swine buildings using real measurement data. An assessment index system and membership functions were established; and predetermined weights were given using analytic hierarchy process (AHP) combined with knowledge of experts. The results show that multi-factors such as temperature, humidity, and concentrations of ammonia (NH 3 ), carbon dioxide (CO 2 ), and hydrogen sulfide (H 2 S) can be successfully integrated in FCE for swine building environment assessment. The FCE method has a high correlation coefficient of 0.737 compared with the method of single-factor evaluation (SFE). The FCE method can significantly increase the sensitivity and perform an effective and integrative assessment. It can be used as part of environmental controlling and warning systems for swine building environment management to improve swine production and welfare. Copyright © 2017 Elsevier B.V. All rights reserved.

Iranian Television Advertisement and Children's Food Preferences.

PubMed

Hajizadehoghaz, Masoomeh; Amini, Maryam; Abdollahi, Afsoun

2016-01-01

In this study, the nature of food commercials in children's television (TV) was monitored and analyzed; simultaneously, the relationship between recalling TV food commercials and children's interest in them and in the consumption of the same food products was evaluated. A total of 108 h children's programs broadcast on two channels (Two and Amouzesh) of Islamic Republic of Iran Broadcasting (IRIB) media organization were monitored (May 6-12, 2015). Simultaneously, a cross-sectional study using 403 primary schoolchildren (201 boys) in four schools of Shirvan, Northeast of Iran, was executed. The children were prompted to recall all TV commercials broadcast on IRIB. Meanwhile, they were directed to define in the list of recalled TV food commercials those were interested in and the commercials (food products) they actually were willing to consume. Regarding the frequency and duration of broadcasting, food commercials ranked fifth and sixth, respectively. Fruit leather and plum paste were the most frequently broadcast food commercials. "High quality" (19%), "good taste" (15%), "novelty", and "message on nutritional composition" (13%) were the most frequent messages used in promoting the sale of food products, respectively. In addition, focus on "high quality/precision in the preparation of the food products" was the most frequently used appeals in TV commercials. There was a significant relationship between recalling TV food commercials and the interest in five out of eight of the commercials (62.5%) ( P < 0.05). The relationship between recalling TV food commercials and the interest in the consumption of the same food product ("Tomato paste B") was statistically significant for 12.5% of the commercials ( P < 0.05). TV food commercials do not encourage healthy eating. The current study provides convincing evidence for policy-makers and researchers to pay more attention to this area.

[Blood-sugar self control. A means for the diabetic of controlling his metabolic management. Quality control of a battery-run pocket size reflectometer (glucose-meter)].

PubMed

Leidinger, F; Jörgens, V; Chantelau, E; Berchtold, P; Berger, M

1980-07-26

Home blood glucose monitoring by diabetic patients has recently been advocated as an effective means to improve metabolic control. The Glucocheck apparatus, a pocket-size battery-driven reflectance-meter (in Germany commercially available under the name Glucose-meter), has been evaluated for accuracy and practicability. In 450 blood glucose measurements, the variance between the values obtained using the Glucocheck apparatus and routine clinical laboratory procedures was +/- 11.7%. Especially in the low range of blood glucose concentrations, the Glucocheck method was very reliable. The quantitative precision of the Glucocheck method depends, however, quite considerably on the ability of the patient to use the apparatus correctly. In order to profit from Glucocheck in clinical practice, particular efforts to educate the patients in its use are necessary.

Bivalent rLP2086 (Trumenba®): Development of a well-characterized vaccine through commercialization.

PubMed

Sunasara, Khurram; Cundy, John; Srinivasan, Sriram; Evans, Brad; Sun, Weiqiang; Cook, Scott; Bortell, Eric; Farley, John; Griffin, Daniel; Bailey Piatchek, Michele; Arch-Douglas, Katherine

2018-05-24

The phrase "Process is the Product" is often applied to biologics, including multicomponent vaccines composed of complex components that evade complete characterization. Vaccine production processes must be defined and locked early in the development cycle to ensure consistent quality of the vaccine throughout scale-up, clinical studies, and commercialization. This approach of front-loading the development work helped facilitate the accelerated approval of the Biologic License Application for the well-characterized vaccine bivalent rLP2086 (Trumenba®, Pfizer Inc) in 2014 under Breakthrough Therapy Designation. Bivalent rLP2086 contains two rLP2086 antigens and is licensed for the prevention of meningococcal meningitis disease caused by Neisseria meningitidis serogroup B in individuals 10-25years of age in the United States. This paper discusses the development of the manufacturing process of the two antigens for the purpose of making it amenable to any manufacturing facility. For the journey to commercialization, the operating model used to manage this highly accelerated program led to a framework that ensured "right the first time" execution, robust process characterization, and proactive process monitoring. This framework enabled quick problem identification and proactive resolutions, resulting in a robust control strategy for the commercial process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bee pollination improves crop quality, shelf life and commercial value.

PubMed

Klatt, Björn K; Holzschuh, Andrea; Westphal, Catrin; Clough, Yann; Smit, Inga; Pawelzik, Elke; Tscharntke, Teja

2014-01-22

Pollination improves the yield of most crop species and contributes to one-third of global crop production, but comprehensive benefits including crop quality are still unknown. Hence, pollination is underestimated by international policies, which is particularly alarming in times of agricultural intensification and diminishing pollination services. In this study, exclusion experiments with strawberries showed bee pollination to improve fruit quality, quantity and market value compared with wind and self-pollination. Bee-pollinated fruits were heavier, had less malformations and reached higher commercial grades. They had increased redness and reduced sugar-acid-ratios and were firmer, thus improving the commercially important shelf life. Longer shelf life reduced fruit loss by at least 11%. This is accounting for 0.32 billion US$ of the 1.44 billion US$ provided by bee pollination to the total value of 2.90 billion US$ made with strawberry selling in the European Union 2009. The fruit quality and yield effects are driven by the pollination-mediated production of hormonal growth regulators, which occur in several pollination-dependent crops. Thus, our comprehensive findings should be transferable to a wide range of crops and demonstrate bee pollination to be a hitherto underestimated but vital and economically important determinant of fruit quality.

Environmental and management factors affecting the welfare of chickens on commercial farms in the United Kingdom and Denmark stocked at five densities.

PubMed

Jones, T A; Donnelly, C A; Stamp Dawkins, M

2005-08-01

Data from a large commercial-scale experiment in which 10 major broiler producer companies stocked whole houses of birds at 30, 34, 38, 42, and 46 kg/m2 were analyzed to identify 1) temperature and humidity profiles achieved throughout the growth cycle, 2) management practices and equipment that contributed to observed variation in environmental conditions, and 3) the extent to which environmental variables affected bird welfare. The study involved a total of 2.7 million birds in 114 houses on commercial farms with measurement of a wide range of environmental and bird variables. Much of the variation in broiler health and welfare was associated with the percentage of time a company could maintain house temperature and RH within limits recommended by the breeder company. RH in the first week of life was particularly important to later health, suggesting that better control of humidity might lead to improved welfare. Key management factors affecting bird welfare were those relating to good ventilation and air control such as the type of ventilation, type of drinker, numbers of stockmen, and litter type. Controlling the environment, particularly temperature, humidity, and air and litter quality, is crucial to broiler chicken welfare. This does not mean that stocking density is unimportant, but lowering stocking density on its own, without regard to the environment the birds experience, is not sufficient. Genuine improvements in bird welfare will come from setting standards that combine stocking density, safeguards on the environment, and the genetic makeup of the birds.

A simple control for sediment-toxicity exposures using the amphipod, Hyalella azteca

USGS Publications Warehouse

Lasier, Peter J.; Urich, Matthew L.

2014-01-01

Sediment-toxicity exposures comparing survival and growth of the freshwater amphipod, Hyalella azteca, are often components of aquatic-habitat assessments. Standardized exposure methods have been established and require evaluations for quality assurance. Test acceptability using performance-based criteria can be determined from exposures to control sediments, which are collected from the environment or formulated from commercially available components. Amending sand with leached alfalfa solids provided a simple formulated sediment that elicited consistently acceptable survival and growth in 28-day exposures with and without a daily feeding regime. A procedure is described for preparing the sediment along with results from comparisons among sand, amended sand, and field-collected sediments that incorporated three feeding regimes.

[Comparative study on the productivity of strains of Pleurotus spp. in commercial cultivation].

PubMed

Vogel, F; Salmones, D

2000-12-01

This paper describes the commercial production of two strains of Pleurotus pulmonarius, selected in the laboratory for their rapid mycelial development and high production of basidiomata, and one commercial strain of Pleurotus ostreatus. Substrate preparation, impact of pathogens and environmental conditions necessary for the production and quality of the fruiting bodies required are discussed.

50 CFR 635.24 - Commercial retention limits for sharks and swordfish.

Code of Federal Regulations, 2010 CFR

2010-10-01

... those sharks with sharks of higher quality or size that are caught later in the trip. Any fish that are... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Commercial retention limits for sharks and... Management Measures § 635.24 Commercial retention limits for sharks and swordfish. The retention limits in...

A rootstock provides water conservation for a grafted commercial tomato (Solanum lycopersicum L.) line in response to mild-drought conditions: a focus on vegetative growth and photosynthetic parameters.

PubMed

Nilsen, Erik T; Freeman, Joshua; Grene, Ruth; Tokuhisa, James

2014-01-01

The development of water stress resistant lines of commercial tomato by breeding or genetic engineering is possible, but will take considerable time before commercial varieties are available for production. However, grafting commercial tomato lines on drought resistant rootstock may produce drought tolerant commercial tomato lines much more rapidly. Due to changing climates and the need for commercial production of vegetables in low quality fields there is an urgent need for stress tolerant commercial lines of vegetables such as tomato. In previous observations we identified a scion root stock combination ('BHN 602' scion grafted onto 'Jjak Kkung' rootstock hereafter identified as 602/Jjak) that had a qualitative drought-tolerance phenotype when compared to the non-grafted line. Based on this initial observation, we studied photosynthesis and vegetative above-ground growth during mild-drought for the 602/Jjak compared with another scion-rootstock combination ('BHN 602' scion grafted onto 'Cheong Gang' rootstock hereafter identified as 602/Cheong) and a non-grafted control. Overall above ground vegetative growth was significantly lower for 602/Jjak in comparison to the other plant lines. Moreover, water potential reduction in response to mild drought was significantly less for 602/Jjak, yet stomatal conductance of all plant-lines were equally inhibited by mild-drought. Light saturated photosynthesis of 602/Jjak was less affected by low water potential than the other two lines as was the % reduction in mesophyll conductance. Therefore, the Jjak Kkung rootstock caused aboveground growth reduction, water conservation and increased photosynthetic tolerance of mild drought. These data show that different rootstocks can change the photosynthetic responses to drought of a high yielding, commercial tomato line. Also, this rapid discovery of one scion-rootstock combination that provided mild-drought tolerance suggests that screening more scion-rootstock combination for stress tolerance may rapidly yield commercially viable, stress tolerant lines of tomato.

Ethical considerations in placebo-controlled randomised clinical trials.

PubMed

Kaufman, Kenneth R

2015-06-01

Ethical considerations in standard medical care and clinical research are underpinnings to quality medicine. Similarly, the placebo-controlled double-blind randomised clinical trial is the gold standard for medical research and fundamental to the development of evidence-based medicine. Researchers and clinicians are challenged by ethical concerns in the informed consent with a need to maximise understanding and minimise therapeutic misconception. This editorial expands on themes raised by Chen et al 's article 'Disclosing the Potential Impact of Placebo Controls in Antidepressant Trials' and serves as an invitation for further submissions to BJPsych Open on ethics, research design and informed consent. None. © The Royal College of Psychiatrists 2015. This is an open access article distributed under the terms of the Creative Commons Non-Commercial, No Derivatives (CC BY-NC-ND) licence.

Sodium alginate as feed additive in cultured sea bream (Sparus aurata): does it modify the quality of the flesh?

PubMed

Peso-Echarri, P; Frontela-Saseta, C; Santaella-Pascual, M; García-Alcázar, A; Abdel, I; Ros-Berruezo, G; Martínez-Graciá, C

2012-11-15

The objective of this study was to evaluate the effect of sodium alginate obtained from brown seaweed as a prebiotic supplement to the feed of reared sea bream (Sparus aurata). Addition of the alginate to a control diet was investigated at both concentrations 2% and 5%. Proximate composition in the flesh were not modified significantly by sodium alginate inclusion in the diet of the sea bream; however the fat and ash content in the specimens supplemented with 5% alginate were found to be significantly higher than those found in individuals who were fed the control diet. No significant differences in mineral content, fatty acid profiles, cholesterol content, texture parameters and sensory acceptability among the three studied groups. Results obtained in this study offer support for the use of alginate as a feed additive in sea bream diets since no significant effects were found in the flesh quality and characteristics of commercial size sea bream. Copyright © 2012 Elsevier Ltd. All rights reserved.

Multiscale analysis of replication technique efficiency for 3D roughness characterization of manufactured surfaces

NASA Astrophysics Data System (ADS)

Jolivet, S.; Mezghani, S.; El Mansori, M.

2016-09-01

The replication of topography has been generally restricted to optimizing material processing technologies in terms of statistical and single-scale features such as roughness. By contrast, manufactured surface topography is highly complex, irregular, and multiscale. In this work, we have demonstrated the use of multiscale analysis on replicates of surface finish to assess the precise control of the finished replica. Five commercial resins used for surface replication were compared. The topography of five standard surfaces representative of common finishing processes were acquired both directly and by a replication technique. Then, they were characterized using the ISO 25178 standard and multiscale decomposition based on a continuous wavelet transform, to compare the roughness transfer quality at different scales. Additionally, atomic force microscope force modulation mode was used in order to compare the resins’ stiffness properties. The results showed that less stiff resins are able to replicate the surface finish along a larger wavelength band. The method was then tested for non-destructive quality control of automotive gear tooth surfaces.

Millimeter-Wave Absorption as a Quality Control Tool for M-Type Hexaferrite Nanopowders

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCloy, John S.; Korolev, Konstantin A.; Crum, Jarrod V.

2013-01-01

Millimeter wave (MMW) absorption measurements have been conducted on commercial samples of large (micrometer-sized) and small (nanometer-sized) particles of BaFe12O19 and SrFe12O19 using a quasi-optical MMW spectrometer and a series of backwards wave oscillators encompassing the 30-120 GHz range. Effective anisotropy of the particles calculated from the resonant absorption frequency indicates lower overall anisotropy in the nano-particles. Due to their high magnetocrystalline anisotropy, both BaFe12O19 and SrFe12O19 are expected to have spin resonances in the 45-55 GHz range. Several of the sampled BaFe12O19 powders did not have MMW absorptions, so they were further investigated by DC magnetization and x-ray diffractionmore » to assess magnetic behavior and structure. The samples with absent MMW absorption contained primarily iron oxides, suggesting that MMW absorption could be used for quality control in hexaferrite powder manufacture.« less

The role of the private sector in the provision of antenatal care: a study of Demographic and Health Surveys from 46 low- and middle-income countries.

PubMed

Powell-Jackson, Timothy; Macleod, David; Benova, Lenka; Lynch, Caroline; Campbell, Oona M R

2015-02-01

To examine the role of the private sector in the provision of antenatal care (ANC) across low- and middle-income countries. Demographic and Health Survey (DHS) data from 46 countries (representing 2.6 billion people) on components of ANC given to 303 908 women aged 15-49 years for most recent birth were used. We identified 79 unique sources of care which were re-coded into home, public, private (commercial) and private (not-for-profit). Use of ANC and a quality of care index (scaled 0-1) were stratified by type of provider, region and wealth quintile. Linear regressions were used to examine the association between provider type and antenatal quality of care score. Across all countries, the main source of ANC was public (54%), followed by private commercial (36%) and home (5%), but there were large variations by region. Home-based ANC was associated with worse quality of care (0.2; 95% CI -0.2 to -0.19) relative to the public sector, while the private not-for-profit sector (0.03; 95% CI 0.02 to 0.04) was better. There were no differences in quality of care between public and private commercial providers. The market for ANC varies considerably between regions. The two largest sectors - public and private commercial - perform similarly in terms of quality of care. Future research should examine the role of the private sector in other health service domains across multiple countries and test what policies and programmes can encourage private providers to contribute to increased coverage, quality and equity of maternal care. © 2014 John Wiley & Sons Ltd.

Cassava flour slurry as a low-cost alternative to commercially available gel for obstetrical ultrasound: a blinded non-inferiority trial comparison of image quality.

PubMed

Aziz, A; Dar, P; Hughes, F; Solorzano, C; Muller, M M; Salmon, C; Salmon, M; Benfield, N

2018-01-12

To evaluate the quality of ultrasound images obtained with cassava flour slurry (CFS) compared with conventional gel in order to determine objectively whether CFS could be a true low-cost alternative. Blinded non-inferiority trial. Obstetrical ultrasound unit in an academic medical centre. Women with a singleton pregnancy, undergoing anatomy ultrasounds. Thirty pregnant women had standard biometry measures obtained with CFS and conventional gel. Images were compared side-by-side in random order by two blinded sonologists and rated for image resolution, detail and total image quality using a 10-cm visual analogue scale. Ratings were compared using paired t-tests. Participant and sonographer experience was measured using five-point Likert scales. Image resolution, detail, and total image quality. Participant experience of gel regarding irritation, messiness, and ease of removal. We found no significant difference between perceived image quality obtained with CFS (mean = 6.2, SD = 1.2) and commercial gel (mean = 6.4, SD = 1.2) [t (28) = -1.1; P = 0.3]. Images were not rated significantly differently for either reviewer in any measure, any standardized image or any view of a specific anatomic structure. All five sonographers rated CFS as easy to obtain clear images and easy for patient and machine cleanup. Only one participant reported itching with CFS. CFS produces comparable image quality to commercial ultrasound gel. The dissemination of these results and the simple CFS recipe could significantly increase access to ultrasound for screening, monitoring and diagnostic purposes in resource-limited settings. This study was internally funded by our department. Low-cost homemade cassava flour slurry creates images equal to commercial ultrasound gel, improving access. © 2018 Royal College of Obstetricians and Gynaecologists.

Materials and manufacturing processes for increased life/reliability. [of turbine wheels

NASA Technical Reports Server (NTRS)

Duttweiler, R. E.

1977-01-01

Improvements in both quality and durability of disk raw material for both military and commercial engines necessitated an entirely new concept in raw material process control which imposes careful selection, screening and sampling of the basic alloy ingredients, followed by careful monitoring of the melting parameters in all phases of the vacuum melting sequence. Special care is taken to preclude solidification conditions that produce adverse levels of segregation. Melt furnaces are routinely cleaned and inspected for contamination. Ingots are also cleaned and inspected before entering the final melt step.

Metal Oxide Sensors for Electronic Noses and Their Application to Food Analysis

PubMed Central

Berna, Amalia

2010-01-01

Electronic noses (E-noses) use various types of electronic gas sensors that have partial specificity. This review focuses on commercial and experimental E-noses that use metal oxide semi-conductors. The review covers quality control applications to food and beverages, including determination of freshness and identification of contaminants or adulteration. Applications of E-noses to a wide range of foods and beverages are considered, including: meat, fish, grains, alcoholic drinks, non-alcoholic drinks, fruits, milk and dairy products, olive oils, nuts, fresh vegetables and eggs. PMID:22319332

The design, development, fabrication and testing of two (2) Non-Spin Platforms, (NSP)

NASA Technical Reports Server (NTRS)

1975-01-01

The non spin platform is a means for achieving the very low acceleration requirements for cost effective space processing experiments on research rocket flights. These platforms have a low initial cost, are re-usable and have extremely low refurbishment cost. In order to attain this goal, commercially available components were used and only the necessary quality control standards were imposed. A detailed system description, the very few design problems encountered, the operational procedures (both pre-flight and post-flight), and the maintenance requirements are described.

Liquid Scintillator Production for the NOvA Experiment

DOE PAGES

Mufson, S.; Baugh, B.; Bower, C.; ...

2015-04-15

The NOvA collaboration blended and delivered 8.8 kt (2.72M gal) of liquid scintillator as the active detector medium to its near and far detectors. The composition of this scintillator was specifically developed to satisfy NOvA's performance requirements. A rigorous set of quality control procedures was put in place to verify that the incoming components and the blended scintillator met these requirements. The scintillator was blended commercially in Hammond, IN. The scintillator was shipped to the NOvA detectors using dedicated stainless steel tanker trailers cleaned to food grade.

Multileaf collimator performance monitoring and improvement using semiautomated quality control testing and statistical process control.

PubMed

Létourneau, Daniel; Wang, An; Amin, Md Nurul; Pearce, Jim; McNiven, Andrea; Keller, Harald; Norrlinger, Bernhard; Jaffray, David A

2014-12-01

High-quality radiation therapy using highly conformal dose distributions and image-guided techniques requires optimum machine delivery performance. In this work, a monitoring system for multileaf collimator (MLC) performance, integrating semiautomated MLC quality control (QC) tests and statistical process control tools, was developed. The MLC performance monitoring system was used for almost a year on two commercially available MLC models. Control charts were used to establish MLC performance and assess test frequency required to achieve a given level of performance. MLC-related interlocks and servicing events were recorded during the monitoring period and were investigated as indicators of MLC performance variations. The QC test developed as part of the MLC performance monitoring system uses 2D megavoltage images (acquired using an electronic portal imaging device) of 23 fields to determine the location of the leaves with respect to the radiation isocenter. The precision of the MLC performance monitoring QC test and the MLC itself was assessed by detecting the MLC leaf positions on 127 megavoltage images of a static field. After initial calibration, the MLC performance monitoring QC test was performed 3-4 times/week over a period of 10-11 months to monitor positional accuracy of individual leaves for two different MLC models. Analysis of test results was performed using individuals control charts per leaf with control limits computed based on the measurements as well as two sets of specifications of ± 0.5 and ± 1 mm. Out-of-specification and out-of-control leaves were automatically flagged by the monitoring system and reviewed monthly by physicists. MLC-related interlocks reported by the linear accelerator and servicing events were recorded to help identify potential causes of nonrandom MLC leaf positioning variations. The precision of the MLC performance monitoring QC test and the MLC itself was within ± 0.22 mm for most MLC leaves and the majority of the apparent leaf motion was attributed to beam spot displacements between irradiations. The MLC QC test was performed 193 and 162 times over the monitoring period for the studied units and recalibration had to be repeated up to three times on one of these units. For both units, rate of MLC interlocks was moderately associated with MLC servicing events. The strongest association with the MLC performance was observed between the MLC servicing events and the total number of out-of-control leaves. The average elapsed time for which the number of out-of-specification or out-of-control leaves was within a given performance threshold was computed and used to assess adequacy of MLC test frequency. A MLC performance monitoring system has been developed and implemented to acquire high-quality QC data at high frequency. This is enabled by the relatively short acquisition time for the images and automatic image analysis. The monitoring system was also used to record and track the rate of MLC-related interlocks and servicing events. MLC performances for two commercially available MLC models have been assessed and the results support monthly test frequency for widely accepted ± 1 mm specifications. Higher QC test frequency is however required to maintain tighter specification and in-control behavior.

CT and MRI slice separation evaluation by LabView developed software.

PubMed

Acri, Giuseppe; Testagrossa, Barbara; Sestito, Angela; Bonanno, Lilla; Vermiglio, Giuseppe

2018-02-01

The efficient use of Computed Tomography (CT) and Magnetic Resonance Imaging (MRI) equipment necessitates establishing adequate quality-control (QC) procedures. In particular, the accuracy of slice separation, during multislices acquisition, requires scan exploration of phantoms containing test objects. To simplify such procedures, a novel phantom and a computerised LabView-based procedure have been devised, enabling determination the midpoint of full width at half maximum (FWHM) in real time while the distance from the profile midpoint of two progressive images is evaluated and measured. The results were compared with those obtained by processing the same phantom images with commercial software. To validate the proposed methodology the Fisher test was conducted on the resulting data sets. In all cases, there was no statistically significant variation between the commercial procedure and the LabView one, which can be used on any CT and MRI diagnostic devices. Copyright © 2017. Published by Elsevier GmbH.

Nondestructive Evaluation Techniques for Development and Characterization of Carbon Nanotube Based Superstructures

NASA Technical Reports Server (NTRS)

Wincheski, Buzz; Kim, Jae-Woo; Sauti, Godfrey; Wainwright, Elliot; Williams, Phillip; Siochi, Emile J.

2014-01-01

Recently, multiple commercial vendors have developed capability for the production of large-scale quantities of high-quality carbon nanotube sheets and yarns. While the materials have found use in electrical shielding applications, development of structural systems composed of a high volume fraction of carbon nanotubes is still lacking. A recent NASA program seeks to address this by prototyping a structural nanotube composite with strength-toweight ratio exceeding current state-of-the-art carbon fiber composites. Commercially available carbon nanotube sheets, tapes, and yarns are being processed into high volume fraction carbon nanotube-polymer nanocomposites. Nondestructive evaluation techniques have been applied throughout this development effort for material characterization and process control. This paper will report on the progress of these efforts, including magnetic characterization of residual catalyst content, Raman scattering characterization of nanotube diameter, defect ratio, and nanotube strain, and polarized Raman scattering for characterization of nanotube alignment.

Edible packaging materials.

PubMed

Janjarasskul, Theeranun; Krochta, John M

2010-01-01

Research groups and the food and pharmaceutical industries recognize edible packaging as a useful alternative or addition to conventional packaging to reduce waste and to create novel applications for improving product stability, quality, safety, variety, and convenience for consumers. Recent studies have explored the ability of biopolymer-based food packaging materials to carry and control-release active compounds. As diverse edible packaging materials derived from various by-products or waste from food industry are being developed, the dry thermoplastic process is advancing rapidly as a feasible commercial edible packaging manufacturing process. The employment of nanocomposite concepts to edible packaging materials promises to improve barrier and mechanical properties and facilitate effective incorporation of bioactive ingredients and other designed functions. In addition to the need for a more fundamental understanding to enable design to desired specifications, edible packaging has to overcome challenges such as regulatory requirements, consumer acceptance, and scaling-up research concepts to commercial applications.

Determination of synthetic food dyes in commercial soft drinks by TLC and ion-pair HPLC.

PubMed

de Andrade, Francisca Ivani; Florindo Guedes, Maria Izabel; Pinto Vieira, Ícaro Gusmão; Pereira Mendes, Francisca Noélia; Salmito Rodrigues, Paula Alves; Costa Maia, Carla Soraya; Marques Ávila, Maria Marlene; de Matos Ribeiro, Luzara

2014-08-15

Synthetic food colourings were analyzed on commercial carbonated orange and grape soft drinks produced in Ceará State, Brazil. Tartrazine (E102), Amaranth (E123), Sunset Yellow (E110) and Brilliant Blue (E133) were extracted from soft drinks using C18 SPE and identified by thin layer chromatography (TLC), this method was used to confirm the composition of food colouring in soft drinks stated on label. The concentration of food colouring in soft drink was determined by ion-pair high performance liquid chromatography with photodiode array detection. The results obtained with the samples confirm that the identification and quantification methods are recommended for quality control of the synthetic colours in soft drinks, as well as to determine whether the levels and lables complies with the recommendations of food dyes legislation. Copyright © 2014 Elsevier Ltd. All rights reserved.

[Research on spatial differentiation of urban stormwater runoff quality by source area monitoring].

PubMed

Li, Li-Qing; Zhu, Ren-Xiao; Guo, Shu-Gang; Yin, Cheng-Qing

2010-12-01

Runoff samples were collected from 14 source areas in Hanyang district during four rain events in an attempt to investigate the spatial differentiation and influencing factors of urban stormwater runoff quality. The outcomes are expected to offer practical guidance in sources control of urban runoff pollution. The results revealed that particle-bound proportion of chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in stormwater runoff were 58% +/- 17%, 65% +/- 13% and 92% +/- 6%, respectively. The fractions of ammonia, nitrate and dissolved organic nitrogen were homogeneous in dissolved nitrogen composition. Urban surface function, traffic volume, land use, population density, and street sweeping practice are the main factors determining spatial differentiation of urban surface runoff quality. The highest magnitude of urban stormwater runoff pollution was expected in the old urban residential area, followed by general residential with restaurants, commercial and transport area, new developments and green land. In addition, the magnitude of road stormwater runoff pollution is positively correlated to traffic volume, in the following order: the first trunk road > the second trunk road > minor road. Street sweeping and critical source areas controls should be implemented to mitigate the adverse effects of urban stormwater runoff on receive waters.

External Quality Assessment for Rubella Virus RNA Detection Using Armored RNA in China.

PubMed

Zhang, D; Lin, G; Yi, L; Hao, M; Fan, G; Yang, X; Peng, R; Ding, J; Zhang, K; Zhang, R; Li, J

2017-02-01

Although tremendous efforts have been made to reduce rubella incidence, there are still 300 new cases of congenital rubella syndrome daily; thus, rubella infections remain one of the leading causes of preventable congenital birth defects. An effective surveillance system, which could be achieved and maintained by using an external quality assessment program, is critical for prevention and control of this disease. Armored RNAs, which are noninfectious and RNase-resistant, were used for encapsulation of the E1 gene of rubella virus and for preparation of a 10-specimen panel for external quality assessment. Thirty-two laboratories across mainland China that used nucleic acid tests for rubella virus RNA detection were included in the external quality assessment program organized by the National Center for Clinical Laboratories of China. Different kinds of commercial kits were used by the laboratories for nucleic acid extraction and TaqMan real-time reverse-transcription PCR for rubella virus RNA detection; 99.2% sensitivity and 100% specificity were achieved in this external quality assessment program. Most of the participating laboratories obtained accurate results for rubella nucleic acid tests, thereby achieving the quality required for regional rubella and congenital rubella syndrome elimination.

Performance Evaluation of "Low-cost" Sensors for Measuring Gaseous and Particle Air Pollutants: Results from Two Years of Field and Laboratory Testing

NASA Astrophysics Data System (ADS)

Feenstra, B. J.; Polidori, A.; Tisopulos, L.; Papapostolou, V.; Zhang, H.; Pathmanabhan, J.

2016-12-01

In recent years great progress has been made in development of low-cost miniature air quality sensing technologies. Such low-cost sensors offer a prospect of providing a real-time spatially dense information on pollutants, however, the quality of the data produced by these sensors is so far untested. In an effort to inform the general public about the actual performance of commercially available low-cost air quality sensors, in June 2014 the South Coast Air Quality Management District (SCAQMD) has established the Air Quality Sensor Performance Evaluation Center (AQ-SPEC). This program performs a thorough characterization of low-cost sensors under ambient (in the field) and controlled (in the laboratory) conditions. During the field testing, air quality sensors are operated side-by-side with Federal Reference Methods and Federal Equivalent Methods (FRM and FEM, respectively), which are routinely used to measure the ambient concentration of gaseous or particle pollutants for regulatory purposes. Field testing is conducted at two of SCAQMD's existing air monitoring stations, one in Rubidoux and one near the I-710 freeway. Sensors that demonstrate an acceptable performance in the field are brought back to the lab where a "characterization chamber" is used to challenge these devices with known concentrations of different particle and gaseous pollutants under different temperature and relative humidity levels. Testing results for each sensor are then summarized in a technical report and, along with other relevant information, posted online on a dedicated website (www.aqmd.gov/aq-spec) to educate the public about the capabilities of commercially available sensors and their potential applications. During this presentation, the results from two years of field and laboratory testing will be presented. The major strengths and weaknesses of some of the most commonly available particle and gaseous sensors will be discussed.

Meteorology drives ambient air quality in a valley: a case of Sukinda chromite mine, one among the ten most polluted areas in the world.

PubMed

Mishra, Soumya Ranjan; Pradhan, Rudra Pratap; Prusty, B Anjan Kumar; Sahu, Sanjat Kumar

2016-07-01

The ambient air quality (AAQ) assessment was undertaken in Sukinda Valley, the chromite hub of India. The possible correlations of meteorological variables with different air quality parameters (PM10, PM2.5, SO2, NO2 and CO) were examined. Being the fourth most polluted area in the globe, Sukinda Valley has always been under attention of researchers, for hexavalent chromium contamination of water. The monitoring was carried out from December 2013 through May 2014 at six strategic locations in the residential and commercial areas around the mining cluster of Sukinda Valley considering the guidelines of Central Pollution Control Board (CPCB). In addition, meteorological parameters viz., temperature, relative humidity, wind speed, wind direction and rainfall, were also monitored. The air quality data were subjected to a general linear model (GLM) coupled with one-way analysis of variance (ANOVA) test for testing the significant difference in the concentration of various parameters among seasons and stations. Further, a two-tailed Pearson's correlation test helped in understanding the influence of meteorological parameters on dispersion of pollutants in the area. All the monitored air quality parameters varied significantly among the monitoring stations suggesting (i) the distance of sampling location to the mine site and other allied activities, (ii) landscape features and topography and (iii) meteorological parameters to be the forcing functions. The area was highly polluted with particulate matters, and in most of the cases, the PM level exceeded the National Ambient Air Quality Standards (NAAQS). The meteorological parameters seemed to play a major role in the dispersion of pollutants around the mine clusters. The role of wind direction, wind speed and temperature was apparent in dispersion of the particulate matters from their source of generation to the surrounding residential and commercial areas of the mine.

Geodetic glacier mass balances at the push of a button: application of Structure from Motion technology on aerial images in mountain regions

NASA Astrophysics Data System (ADS)

Bolch, T.; Mölg, N.

2017-12-01

The application of Structure-from-Motion (SfM) to generate digital terrain models (DTMs) derived out of images from various kinds of sources has strongly increased in recent years. The major reason for this is its easy-to-use handling in comparison to conventional photogrammetry. In glaciology, DTMs are intensely used, among others, to calculate the geodetic mass balances. Few studies investigated the application of SfM to aerial images in mountainous terrain and results look promising. We tested this technique in a demanding environment in the Swiss Alps including very steep slopes, snow and ice covered terrain. SfM (using the commercial software packages of Agisoft Photoscan and Pix4DMapper) and conventional photogrammetry (ERDAS Photogrammetry) were applied on archival aerial images for nine dates between 1946 and 2005 the results were compared regarding bundle adjustment and final DTM quality. The overall precision of the DTMs could be defined with the use of a modern, high-quality reference DTM by Swisstopo. Results suggest a high performance of SfM to produce DTMs of similar quality as conventional photogrammetry. A ground resolution of high quality (little noise and artefacts) can be up to 50% higher, with 3-6 times less user effort. However, the controls on the commercial SfM software packages are limited in comparison to ERDAS Photogrammetry. SfM performs less reliably when few images with little overlap are processed. Overall, the uncertainty of DTMs from the different software are comparable and mostly within the uncertainty range of the reference DTM, making them highly valuable for glaciological purposes. Even though SfM facilitates the largely automated production of high quality DTMs, the user is not exempt from a thorough quality check, at best with reference data where available.

Building Air Quality Guide: A Guide for Building Owners and Facility Managers

EPA Pesticide Factsheets

The Building Air Quality, developed by the EPA and the National Institute for Occupational Safety and Health, provides practical suggestions on preventing, identifying, and resolving indoor air quality (IAQ) problems in public and commercial buildings.

Characterisation of commercial Perna canaliculus samples and development of extemporaneous oral veterinary paste formulations containing Perna.

PubMed

Juliano, Claudia; Manconi, Paola; Cossu, Massimo

2016-09-01

Perna canaliculus is a nutritional supplement recently studied and highly recommended for its anti-inflammatory effects in both animals and humans. In this study, the physicochemical properties, the microbiological quality, the total lipid content and fatty acids composition of three commercial samples of Perna powder were determined. Subsequently, three simple formulations of extemporaneous oral pastes containing Perna were prepared and designed for veterinary use. Their microbiological stability was assessed after 1-month storage at either room temperature or 35 °C. The results demonstrated that commercial Perna samples lack homogeneity, in regard to some technological properties and fatty acid composition; therefore, a preliminary characterisation of commercial Perna samples is recommended to assure the quality of formulations containing this nutritional supplement. Oral paste formulations are easy and simple to prepare and show good physical and microbiological stability, suggesting their large-scale production.

Quality of basic life support when using different commercially available public access defibrillators.

PubMed

Müller, Michael P; Poenicke, Cynthia; Kurth, Maxi; Richter, Torsten; Koch, Thea; Eisold, Carolin; Pfältzer, Adrian; Heller, Axel R

2015-06-21

Basic life support (BLS) guidelines focus on chest compressions with a minimal no-flow fraction (NFF), early defibrillation, and a short perishock pause. By using an automated external defibrillator (AED) lay persons are guided through the process of attaching electrodes and initiating defibrillation. It is unclear, however, to what extent the voice instructions given by the AED might influence the quality of initial resuscitation. Using a patient simulator, 8 different commercially available AEDs were evaluated within two different BLS scenarios (ventricular fibrillation vs. asystole). A BLS certified instructor acted according to the current European Resuscitation Council 2010 Guidelines and followed all of the AED voice prompts. In a second set of scenarios, the rescuer anticipated the appropriate actions and started already before the AED stopped speaking. A BLS scenario without AED served as the control. All scenarios were run three times. The time until the first chest compression was 25 ± 2 seconds without the AED and ranged from 50 ± 3 to 148 ± 13 seconds with the AED depending on the model used. The NFF was .26 ± .01 without the AED and between .37 ± .01 and .72 ± .01 when an AED was used. The perishock pause ranged from 12 ± 0 to 46 ± 0 seconds. The optimized sequence of actions reduced the NFF, which ranged now from .32 ± .01 to .41 ± .01, and the perishock pause ranging from 1 ± 1 to 19 ± 1 seconds. Voice prompts given by commercially available AED merely meet the requirements of current evidence in basic life support. Furthermore, there is a significant difference between devices with regard to time until the first chest compression, perishock pause, no-flow fraction and other objective measures of the quality of BLS. However, the BLS quality may be improved with optimized handling of the AED. Thus, rescuers should be trained on the respective AED devices, and manufacturers should expend more effort in improving user guidance to shorten the NFF and perishock pause.

Quality of internet-based decision aids for shoulder arthritis: what are patients reading?

PubMed

Somerson, Jeremy S; Bois, Aaron J; Jeng, Jeffrey; Bohsali, Kamal I; Hinchey, John W; Wirth, Michael A

2018-04-11

The objective of this study was to assess the source, quality, accuracy, and completeness of Internet-based information for shoulder arthritis. A web search was performed using three common Internet search engines and the top 50 sites from each search were analyzed. Information sources were categorized into academic, commercial, non-profit, and physician sites. Information quality was measured using the Health On the Net (HON) Foundation principles, content accuracy by counting factual errors and completeness using a custom template. After removal of duplicates and sites that did not provide an overview of shoulder arthritis, 49 websites remained for analysis. The majority of sites were from commercial (n = 16, 33%) and physician (n = 16, 33%) sources. An additional 12 sites (24%) were from an academic institution and five sites (10%) were from a non-profit organization. Commercial sites had the highest number of errors, with a five-fold likelihood of containing an error compared to an academic site. Non-profit sites had the highest HON scores, with an average of 9.6 points on a 16-point scale. The completeness score was highest for academic sites, with an average score of 19.2 ± 6.7 (maximum score of 49 points); other information sources had lower scores (commercial, 15.2 ± 2.9; non-profit, 18.7 ± 6.8; physician, 16.6 ± 6.3). Patient information on the Internet regarding shoulder arthritis is of mixed accuracy, quality, and completeness. Surgeons should actively direct patients to higher-quality Internet sources.

Qualitative assessment of precocious puberty-related user-created contents on YouTube.

PubMed

Nam, Hyo-Kyoung; Bang, Soo Min; Rhie, Young Jun; Park, Sang Hee; Lee, Kee-Hyoung

2015-09-01

User-created content (UCC) has provided a considerable amount of medical information and become an important source. We aimed to evaluate the quality and scientific accuracy of precocious puberty-related UCC on YouTube. The keywords "precocious puberty", "early puberty", "sexual precocity", and "precocity" were searched for on YouTube during June and July 2014. More than 1,500 UCC matched the keywords. According to the information provider, UCC was classified as medical, oriental, or commercial & others. We evaluated the quality and scientific accuracy of the information provided in UCC using the DISCERN instrument and information scores, respectively. We selected 51 UCC, which were categorized into three types: medical (n=17), oriental (n=17), or commercial & others (n=17). The overall quality score for medical UCC (3.4) was significantly higher relative to those of oriental and commercial & others UCC (2.8 and 2.3, respectively) (P<0.001). In the assessment of scientific accuracy, the mean information score for medical UCC (30.7) was significantly higher than those of oriental and commercial & others UCC (15.9 and 5.1, respectively) (P<0.001). The mean duration of oriental UCC was the longest (P<0.001), however, it was viewed less frequently among them (P=0.086). The quality and accuracy of precocious puberty-related health information in UCC were variable and often unreliable. The overall quality of UCC regarding precocious puberty was moderate. Only medical UCC provided scientifically accurate information. As UCC becomes a popular source of health information, it is important to provide reliable, scientifically accurate information.

Qualitative assessment of precocious puberty-related user-created contents on YouTube

PubMed Central

Nam, Hyo-Kyoung; Bang, Soo Min; Rhie, Young Jun; Park, Sang Hee

2015-01-01

Purpose User-created content (UCC) has provided a considerable amount of medical information and become an important source. We aimed to evaluate the quality and scientific accuracy of precocious puberty-related UCC on YouTube. Methods The keywords "precocious puberty", "early puberty", "sexual precocity", and "precocity" were searched for on YouTube during June and July 2014. More than 1,500 UCC matched the keywords. According to the information provider, UCC was classified as medical, oriental, or commercial & others. We evaluated the quality and scientific accuracy of the information provided in UCC using the DISCERN instrument and information scores, respectively. Results We selected 51 UCC, which were categorized into three types: medical (n=17), oriental (n=17), or commercial & others (n=17). The overall quality score for medical UCC (3.4) was significantly higher relative to those of oriental and commercial & others UCC (2.8 and 2.3, respectively) (P<0.001). In the assessment of scientific accuracy, the mean information score for medical UCC (30.7) was significantly higher than those of oriental and commercial & others UCC (15.9 and 5.1, respectively) (P<0.001). The mean duration of oriental UCC was the longest (P<0.001), however, it was viewed less frequently among them (P=0.086). Conclusion The quality and accuracy of precocious puberty-related health information in UCC were variable and often unreliable. The overall quality of UCC regarding precocious puberty was moderate. Only medical UCC provided scientifically accurate information. As UCC becomes a popular source of health information, it is important to provide reliable, scientifically accurate information. PMID:26512350

Improving tablet coating robustness by selecting critical process parameters from retrospective data.

PubMed

Galí, A; García-Montoya, E; Ascaso, M; Pérez-Lozano, P; Ticó, J R; Miñarro, M; Suñé-Negre, J M

2016-09-01

Although tablet coating processes are widely used in the pharmaceutical industry, they often lack adequate robustness. Up-scaling can be challenging as minor changes in parameters can lead to varying quality results. To select critical process parameters (CPP) using retrospective data of a commercial product and to establish a design of experiments (DoE) that would improve the robustness of the coating process. A retrospective analysis of data from 36 commercial batches. Batches were selected based on the quality results generated during batch release, some of which revealed quality deviations concerning the appearance of the coated tablets. The product is already marketed and belongs to the portfolio of a multinational pharmaceutical company. The Statgraphics 5.1 software was used for data processing to determine critical process parameters in order to propose new working ranges. This study confirms that it is possible to determine the critical process parameters and create design spaces based on retrospective data of commercial batches. This type of analysis is thus converted into a tool to optimize the robustness of existing processes. Our results show that a design space can be established with minimum investment in experiments, since current commercial batch data are processed statistically.

26 CFR 1.892-5 - Controlled commercial entity.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Controlled commercial entity. 1.892-5 Section 1... (CONTINUED) INCOME TAXES Miscellaneous Provisions § 1.892-5 Controlled commercial entity. (a)-(a)(2...)(B), the term entity means and includes a corporation, a partnership, a trust (including a pension...

Advanced process control framework initiative

NASA Astrophysics Data System (ADS)

Hill, Tom; Nettles, Steve

1997-01-01

The semiconductor industry, one the world's most fiercely competitive industries, is driven by increasingly complex process technologies and global competition to improve cycle time, quality, and process flexibility. Due to the complexity of these problems, current process control techniques are generally nonautomated, time-consuming, reactive, nonadaptive, and focused on individual fabrication tools and processes. As the semiconductor industry moves into higher density processes, radical new approaches are required. To address the need for advanced factory-level process control in this environment, Honeywell, Advanced Micro Devices (AMD), and SEMATECH formed the Advanced Process Control Framework Initiative (APCFI) joint research project. The project defines and demonstrates an Advanced Process Control (APC) approach based on SEMATECH's Computer Integrated Manufacturing (CIM) Framework. Its scope includes the coordination of Manufacturing Execution Systems, process control tools, and wafer fabrication equipment to provide necessary process control capabilities. Moreover, it takes advantage of the CIM Framework to integrate and coordinate applications from other suppliers that provide services necessary for the overall system to function. This presentation discusses the key concept of model-based process control that differentiates the APC Framework. This major improvement over current methods enables new systematic process control by linking the knowledge of key process settings to desired product characteristics that reside in models created with commercial model development tools The unique framework-based approach facilitates integration of commercial tools and reuse of their data by tying them together in an object-based structure. The presentation also explores the perspective of each organization's involvement in the APCFI project. Each has complementary goals and expertise to contribute; Honeywell represents the supplier viewpoint, AMD represents the user with 'real customer requirements', and SEMATECH provides a consensus-building organization that widely disseminates technology to suppliers and users in the semiconductor industry that face similar equipment and factory control systems challenges.

Teaching Quality and Student Satisfaction: Nexus or Simulacrum?

ERIC Educational Resources Information Center

Beecham, Rod

2009-01-01

Quality has clear meanings when associated with specific phenomena. The relative nature of quality in commercial contexts, specifically in relation to manufactured goods, has been studied. In service industries there is no satisfactory indicator of quality. The Likert-scale questionnaire does not allow the researcher to distinguish between…

Replacement of mineral fertilizers with anaerobically digested pig slurry in paddy fields: assessment of plant growth and grain quality.

PubMed

Zhang, Jin; Wang, Minyan; Cao, Yucheng; Liang, Peng; Wu, Shengchun; Leung, Anna Oi Wah; Christie, Peter

2017-04-01

Rice cultivation requires large quantities of irrigation water and mineral fertilizers. This provides an opportunity for the recycling of the plant nutrients in anaerobically digested pig slurry, large amounts of which are generated in Chinese pig farms. Hence, to promote the sustainable development of livestock and poultry breeding and rice production, a micro-plot field experiment was carried out to assess whether or not slurry can replace mineral fertilizers in rice paddy production in terms of plant tillering, grain quality, and yields. The results indicate that the total N content of the slurry can serve as an alternative source of N when compared to the control (450 kg ha -1 commercial compound fertilizer (N/P 2 O 5 /K 2 O = 15:15:15) as basal fertilizer, 300 kg ha -1 urea (N% = 46), and 150 kg ha -1 commercial compound fertilizer as top-dressed fertilizer). No negative effects on plant growth or grain yield were observed, although there may be a potential risk due to an increase in grain Cu concentration. The amylose content and gel consistency of the rice grains were enhanced significantly by the use of slurry as a basal fertilizer, but the grain protein and total amino acid contents decreased. The results suggest that anaerobically digested pig slurry can replace mineral fertilizers in rice production when applied as a basal dressing together with urea and commercial compound fertilizer as top-dressed fertilizers.

Current Cytology Practices in Korea: A Nationwide Survey by the Korean Society for Cytopathology

PubMed Central

Oh, Eun Ji; Jung, Chan Kwon; Kim, Dong-Hoon; Kim, Han Kyeom; Kim, Wan Seop; Jin, So-Young; Yoon, Hye Kyoung

2017-01-01

Background Limited data are available on the current status of cytology practices in Korea. This nationwide study presents Korean cytology statistics from 2015. Methods A nationwide survey was conducted in 2016 as a part of the mandatory quality-control program by the Korean Society for Cytopathology. The questionnaire was sent to 208 medical institutions performing cytopathologic examinations in Korea. Individual institutions were asked to submit their annual cytology statistical reports and gynecologic cytology-histology correlation data for 2015. Results Responses were obtained from 206 medical institutions including 83 university hospitals, 87 general hospitals, and 36 commercial laboratories. A total of 8,284,952 cytologic examinations were performed in 2015, primarily in commercial laboratories (74.9%). The most common cytology specimens were gynecologic samples (81.3%). Conventional smears and liquid-based cytology were performed in 6,190,526 (74.7%) and 2,094,426 (25.3%) cases, respectively. The overall diagnostic concordance rate between cytologic and histologic diagnoses of uterine cervical samples was 70.5%. Discordant cases were classified into three categories: category A (minimal clinical impact, 17.4%), category B (moderate clinical impact, 10.2%), and category C (major clinical impact, 1.9%). The ratio of atypical squamous cells of undetermined significance to squamous intraepithelial lesion was 1.6 in university hospitals, 2.9 in general hospitals, and 4.9 in commercial laboratories. Conclusions This survey reveals the current status and trend of cytology practices in Korea. The results of this study can serve as basic data for the establishment of nationwide cytopathology policies and quality improvement guidelines in Korean medical institutions. PMID:28950443

Effect of storage temperature and duration on the behavior of Escherichia coli O157:H7 on packaged fresh-cut salad containing romaine and iceberg lettuce.

PubMed

Luo, Yaguang; He, Qiang; McEvoy, James L

2010-09-01

This study investigated the impact of storage temperature and duration on the fate of Escherichia coli O157:H7 on commercially packaged lettuce salads, and on product quality. Fresh-cut Romaine and Iceberg lettuce salads of different commercial brands were obtained from both retail and wholesale stores. The packages were cut open at one end, the lettuce salad inoculated with E. coli O157:H7 via a fine mist spray, and resealed with or without an initial N(2) flush to match the original package atmospheric levels. The products were stored at 5 and 12 °C until their labeled "Best If Used By" dates, and the microbial counts and product quality were monitored periodically. The results indicate that storage at 5 °C allowed E. coli O157:H7 to survive, but limited its growth, whereas storage at 12 °C facilitated the proliferation of E. coli O157:H7. There was more than 2.0 log CFU/g increase in E. coli O157:H7 populations on lettuce when held at 12 °C for 3 d, followed by additional growth during the remainder of the storage period. Although there was eventually a significant decline in visual quality of lettuce held at 12 °C, the quality of this lettuce was still fully acceptable when E. coli O157:H7 growth reached a statistically significant level. Therefore, maintaining fresh-cut products at 5 °C or below is critical for reducing the food safety risks as E. coli O157:H7 grows at a rapid, temperature-dependent rate prior to significant quality deterioration. Specific information regarding the effect of temperature on pathogen growth on leafy greens is needed to develop science-based food safety guidelines and practices by the regulatory agencies and produce industry. Temperature control is commonly thought to promote quality of leafy greens, not safety, based at least partially on a theory that product quality deterioration precedes pathogen growth at elevated temperatures. This prevalent attitude results in temperature abuse incidents being frequently overlooked in the supply chain. This study demonstrates that human pathogens, such as E. coli O157:H7, can grow significantly on commercially packaged lettuce salads while the product's visual quality is fully acceptable. Packaged fresh-cut salads are marketed as "ready-to-eat" while lacking an effective pathogen kill step during their preparation. Thus, maintaining storage temperature at 5 °C or below is critical to prevent pathogen proliferation and mitigate food safety risks should pathogen contamination inadvertently occur during crop growth or postharvest fresh-cut processing.

Automated Boiler Combustion Controls for Emission Reduction and Efficiency Improvement

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

1998-12-02

In the late 1980s, then President Bush visited Krakow, Poland. The terrible air quality theremotivated him to initiate a USAID-funded program, managed by DOE, entitled "Krakow Clean Fossil Fuels and Energy Efficiency Program." The primary objective of this program was to encourage the formation of commercial ventures between U.S. and Polish firms to provide equipment and/or services to reduce pollution from low-emission sources in Krakow, Poland. This program led to the award of a number of cooperative agreements, including one to Control Techtronics International. The technical objective of CTI's cooperative agreement is to apply combustion controls to existing boiler plantsmore » in Krakow and transfer knowledge and technology through a joint U.S. and Polish commercial venture. CTI installed automatic combustion controls on five coal boilers for the district heating system in Krakow. Three of these were for domestic hot-water boilers, and two were for steam for industrial boilers. The following results have occurred due to the addition of CTI's combustion controls on these five existing boilers: ! 25% energy savings ! 85% reduction in particulate emissions The joint venture company CTI-Polska was then established. Eleven additional technical and costing proposals were initiated to upgrade other coal boilers in Krakow. To date, no co-financing has been made available on the Polish side. CTI-Polska continues in operation, serving customers in Russia and Ukraine. Should the market in Poland materialize, the joint venture company is established there to provide equipment and service.« less

Evaluating the accuracy of orthophotos and 3D models from UAV photogrammetry

NASA Astrophysics Data System (ADS)

Julge, Kalev; Ellmann, Artu

2015-04-01

Rapid development of unmanned aerial vehicles (UAV) in recent years has made their use for various applications more feasible. This contribution evaluates the accuracy and quality of different UAV remote sensing products (i.e. orthorectified image, point cloud and 3D model). Two different autonomous fixed wing UAV systems were used to collect the aerial photographs. One is a mass-produced commercial UAV system, the other is a similar state-of-the-art UAV system. Three different study areas with varying sizes and characteristics (including urban areas, forests, fields, etc.) were surveyed. The UAV point clouds, 3D models and orthophotos were generated with three different commercial and free-ware software. The performance of each of these was evaluated. The effect of flying height on the accuracy of the results was explored, as well as the optimum number and placement of ground control points. Also the achieved results, when the only georeferencing data originates from the UAV system's on-board GNSS and inertial measurement unit, are investigated. Problems regarding the alignment of certain types of aerial photos (e.g. captured over forested areas) are discussed. The quality and accuracy of UAV photogrammetry products are evaluated by comparing them with control measurements made with GNSS-measurements on the ground, as well as high-resolution airborne laser scanning data and other available orthophotos (e.g. those acquired for large scale national mapping). Vertical comparisons are made on surfaces that have remained unchanged in all campaigns, e.g. paved roads. Planar comparisons are performed by control surveys of objects that are clearly identifiable on orthophotos. The statistics of these differences are used to evaluate the accuracy of UAV remote sensing. Some recommendations are given on how to conduct UAV mapping campaigns cost-effectively and with minimal time-consumption while still ensuring the quality and accuracy of the UAV data products. Also the benefits and drawbacks of UAV remote sensing compared to more traditional methods (e.g. national mapping from airplanes or direct measurements on the ground with GNSS devices or total stations) are outlined.

26 CFR 1.892-5 - Controlled commercial entity.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 9 2011-04-01 2011-04-01 false Controlled commercial entity. 1.892-5 Section 1... (CONTINUED) INCOME TAXES (CONTINUED) Miscellaneous Provisions § 1.892-5 Controlled commercial entity. (a)-(a... section 892(a)(2)(B), the term entity means and includes a corporation, a partnership, a trust (including...

Model predictive control of a solar-thermal reactor

NASA Astrophysics Data System (ADS)

Saade Saade, Maria Elizabeth

Solar-thermal reactors represent a promising alternative to fossil fuels because they can harvest solar energy and transform it into storable and transportable fuels. The operation of solar-thermal reactors is restricted by the available sunlight and its inherently transient behavior, which affects the performance of the reactors and limits their efficiency. Before solar-thermal reactors can become commercially viable, they need to be able to maintain a continuous high-performance operation, even in the presence of passing clouds. A well-designed control system can preserve product quality and maintain stable product compositions, resulting in a more efficient and cost-effective operation, which can ultimately lead to scale-up and commercialization of solar thermochemical technologies. In this work, we propose a model predictive control (MPC) system for a solar-thermal reactor for the steam-gasification of biomass. The proposed controller aims at rejecting the disturbances in solar irradiation caused by the presence of clouds. A first-principles dynamic model of the process was developed. The model was used to study the dynamic responses of the process variables and to identify a linear time-invariant model used in the MPC algorithm. To provide an estimation of the disturbances for the control algorithm, a one-minute-ahead direct normal irradiance (DNI) predictor was developed. The proposed predictor utilizes information obtained through the analysis of sky images, in combination with current atmospheric measurements, to produce the DNI forecast. In the end, a robust controller was designed capable of rejecting disturbances within the operating region. Extensive simulation experiments showed that the controller outperforms a finely-tuned multi-loop feedback control strategy. The results obtained suggest that our controller is suitable for practical implementation.

[Comparison between the LightCycler CMV Quant Kit (Roche Diagnostics) with a standardized in-house Taqman assay for cytomegalovirus blood viral load quantification].

PubMed

Alain, S; Lachaise, V; Hantz, S; Denis, F

2010-04-01

The broad use of cytomegalovirus (CMV) viral load quantification in blood to follow immunosuppressed patients need standardized assays. Choice of whole blood allows follow-up for several viruses and simplifies pretreatment and storage of samples. We therefore evaluated the LightCycler CMV Quant Kit (Roche Diagnostics) assay on whole blood after a manual extraction (High Pure viral nucleic acid kit, Roche Diagnostics), using as a reference an in-house Taqman assay (LC1UL83) which has been validated in various clinical situations. A panel obtained by serial dilutions of a virion stock in CMV whole blood, a commercial plasma quality control (VQC, Argène, France) crude or diluted in whole blood, infected cells extracts and 46 clinical samples from transplanted patients were tested simultaneously by both techniques. For plasma quality controls, both PCR assays are correlated VQC (R(2)=0.93). On whole blood or infected cells dilutions, correlation shows an overestimation by the LC1UL83 assay (mean 1.2 log copies/ml) over 3 log though R(2)=0.94. Results with CMV Quant Kit are closer to expected values. Results on clinical samples are close to quality controls with a lower variation of quantification (0.76 log copies/ml). CMV Quant Kit performs well when compared with a clinically validated PCR. Quality control results showed discrepancies between plasma and whole blood, demonstrating the need for whole blood standardized panels to compare the methods. This underlines the need to follow a patient with the same technique during his follow-up. Copyright 2009 Elsevier Masson SAS. All rights reserved.

Effects of different source additives and wilt conditions on the pH value, aerobic stability, and carbohydrate and protein fractions of alfalfa silage.

PubMed

Tao, Lian; Zhou, He; Zhang, Naifeng; Si, Bingwen; Tu, Yan; Ma, Tao; Diao, Qiyu

2017-01-01

To improve the silage quality and reduce the silage additive cost, the present experiment was designed to evaluate the potential of applying the fermented juice of epiphytic lactic acid bacteria (FJLB) as an additive in alfalfa silage. The effects of FJLB on the fermentation quality, carbohydrate and protein fractions, and aerobic stability of alfalfa silage wilted under five different conditions were investigated and compared with commercial lactic acid bacteria (CLAB) and the control. The FJLB application decreased the pH value, the volatile fatty acids and non-protein nitrogen content, and the loss of sugar by 9.9%, 22.9%, 19.6% and 9.6%, respectively; it increased the lactic acid concentration by 29.5% and the aerobic stability by 17 h in comparison to the control. The FJLB application also decreased the pH value (4.44 vs. 4.66) and volatile fatty acid content (38.32 vs. 44.82) and increased the lactic acid concentration (68.99 vs. 63.29) in comparison to the CLAB-treated silage. However, the FJLB treatment had lower aerobic stability (254 h vs. 274 h) than the CLAB treatment. The FJLB application improved silage quality in comparison to the control; in addition, its effect as a fermentation stimulant may be comparable to or even better than CLAB. © 2016 Japanese Society of Animal Science.

Incorporation of Chlorella vulgaris and Spirulina maxima biomass in pasta products. Part 1: Preparation and evaluation.

PubMed

Fradique, Mónica; Batista, Ana Paula; Nunes, M Cristiana; Gouveia, Luísa; Bandarra, Narcisa M; Raymundo, Anabela

2010-08-15

Microalgae are able to enhance the nutritional content of conventional foods and hence to positively affect human health, due to their original chemical composition. The aim of the present study was to prepare fresh spaghetti enriched with different amounts of microalgae biomass (Chlorella vulgaris and Spirulina maxima) and to compare the quality parameters (optimal cooking time, cooking losses, swelling index and water absorption), chemical composition, instrumental texture and colour of the raw and cooked pasta enriched with microalgae biomass with standard semolina spaghetti. The incorporation of microalgae results in an increase of quality parameters when compared to the control sample. The colour of microalgae pastas remained relatively stable after cooking. The addition of microalgae resulted in an increase in the raw pasta firmness when compared to the control sample. Of all the microalgae studied, an increase in the biomass concentration (0.5-2.0%) resulted in a general tendency of an increase in the pasta firmness. Sensory analysis revealed that microalgae pastas had higher acceptance scores by the panellists than the control pasta. Microalgae pastas presented very appellative colours, such as orange and green, similar to pastas produced with vegetables, with nutritional advantages, showing energetic values similar to commercial pastas. The use of microalgae biomass can enhance the nutritional and sensorial quality of pasta, without affecting its cooking and textural properties. Copyright (c) 2010 Society of Chemical Industry.

Effects of acetic acid and hydrogen peroxide application during defeathering on the microbiological quality of broiler carcasses prior to evisceration.

PubMed

Dickens, J A; Whittemore, A D

1997-04-01

The microbiological quality and skin appearance of New York dressed broiler carcasses were determined in two separate experiments after a water control, acetic acid, or H2O2 spray during defeathering. Broilers were picked up from a local processor and transported in coops to the pilot facility. In both experiments, commercial processing parameters were followed up to the defeathering step. After feather removal, the vents of all carcasses were blocked with a cotton plug to prevent contamination of the whole carcass rinse diluent with fecal material from the lower gut. The neck and feet were removed, and the carcasses were placed in individual plastic bags in preparation for a whole carcass rinse. Results showed a statistically significant reduction (P < 0.05) in the log10 total aerobic plate counts for carcasses treated with 1% acetic acid in comparison to the water control (log10 cfu counts = 3.93 and 4.53, respectively). No differences were observed in skin appearance due to the 1% acid treatment. The addition of 0.5, 1, or 1.5% H2O2 to spray waters had no effect on microbiological quality of the carcasses when compared to the water control (4.92, 5.01, 4.91, and 4.99 log10 counts, respectively). The skin of carcasses treated with hydrogen peroxide, regardless of the concentration was bleached and bloated.

Commercialization of veterinary viral vaccines.

PubMed

Flore, P H

2004-12-01

If vaccines are to reliably prevent disease, they must be developed, produced and quality-controlled according to very strict regulations and procedures. Veterinary viral vaccine registrations are governed by different rules in different countries, but these rules all emphasize that the quality of the raw materials--the cells, eggs, animals or plants that are used in production--need to be carefully controlled. The veterinary vaccine business is also very cost-conscious. Emphasis over the last 5-10 years has therefore been to develop culture systems that minimize labor and sterility problems and thus provide for reliable and cost-effective production. Implementing these often more complex systems in a production environment takes considerable effort, first in scale-up trials and further down the line in convincing production personnel to change their familiar system for something new and possibly untried. To complete scale-up trials successfully, it is absolutely necessary to understand the biochemistry of the cells and the influence of the virus on the cells under scale-up and later production conditions. Once a viral product can be produced on a large scale, it is imperative that the quality of the end-product is controlled in an intelligent way. One needs to know whether the end-product performs in the animal as was intended during its conception in the research and development department. The development of the appropriate tests to demonstrate this plays an important role in the successful development of a vaccine.

Automatic and remote controlled ictal SPECT injection for seizure focus localization by use of a commercial contrast agent application pump.

PubMed

Feichtinger, Michael; Eder, Hans; Holl, Alexander; Körner, Eva; Zmugg, Gerda; Aigner, Reingard; Fazekas, Franz; Ott, Erwin

2007-07-01

In the presurgical evaluation of patients with partial epilepsy, the ictal single photon emission computed tomography (SPECT) is a useful noninvasive diagnostic tool for seizure focus localization. To achieve optimal SPECT scan quality, ictal tracer injection should be carried out as quickly as possible after the seizure onset and under highest safety conditions possible. Compared to the commonly used manual injection, an automatic administration of the radioactive tracer may provide higher quality standards for this procedure. In this study, therefore, we retrospectively analyzed efficiency and safety of an automatic injection system for ictal SPECT tracer application. Over a 31-month period, 26 patients underwent ictal SPECT by use of an automatic remote-controlled injection pump originally designed for CT-contrast agent application. Various factors were reviewed, including latency of ictal injection, radiation safety parameters, and ictal seizure onset localizing value. Times between seizure onset and tracer injection ranged between 3 and 48 s. In 21 of 26 patients ictal SPECT supported the localization of the epileptogenic focus in the course of the presurgical evaluation. In all cases ictal SPECT tracer injection was performed with a high degree of safety to patients and staff. Ictal SPECT by use of a remote-controlled CT-contrast agent injection system provides a high scan quality and is a safe and confirmatory presurgical evaluation technique in the epilepsy-monitoring unit.

Adaptation of commercial biomarker kits and proposal for 'drug development kits' to support bioanalysis: call for action.

PubMed

Islam, Rafiqul; Kar, Sumit; Islam, Clarinda; Farmen, Raymond

2018-06-01

There has been an increased use of commercial kits for biomarker measurement, commensurate with the increased demand for biomarkers in drug development. However, in most cases these kits do not meet the quality attributes for use in regulated environment. The process for adaptation of these kits can be frustrating, time consuming and resource intensive. In addition, a lack of harmonized guidance for the validation of biomarker poses a significant challenge in the adaptation of kits in a regulated environment. The purpose of this perspective is to propose a tiered approach to commercial drug development kits with clearly defined quality attributes and to demonstrate how these kits can be adapted to perform analytical validation in a regulated environment.

External Quality Assessment for the Detection of Measles Virus by Reverse Transcription-PCR Using Armored RNA

PubMed Central

Jia, Tingting; Zhang, Lei; Wang, Guojing; Zhang, Rui; Zhang, Kuo; Lin, Guigao; Xie, Jiehong; Wang, Lunan; Li, Jinming

2015-01-01

In recent years, nucleic acid tests for detection of measles virus RNA have been widely applied in laboratories belonging to the measles surveillance system of China. An external quality assessment program was established by the National Center for Clinical Laboratories to evaluate the performance of nucleic acid tests for measles virus. The external quality assessment panel, which consisted of 10 specimens, was prepared using armored RNAs, complex of noninfectious MS2 bacteriophage coat proteins encapsulated RNA of measles virus, as measles virus surrogate controls. Conserved sequences amplified from a circulating measles virus strain or from a vaccine strain were encapsulated into these armored RNAs. Forty-one participating laboratories from 15 provinces, municipalities, or autonomous regions that currently conduct molecular detection of measles virus enrolled in the external quality assessment program, including 40 measles surveillance system laboratories and one diagnostic reagent manufacturer. Forty laboratories used commercial reverse transcription-quantitative PCR kits, with only one laboratory applying a conventional PCR method developed in-house. The results indicated that most of the participants (38/41, 92.7%) were able to accurately detect the panel with 100% sensitivity and 100% specificity. Although a wide range of commercially available kits for nucleic acid extraction and reverse transcription polymerase chain reaction were used by the participants, only two false-negative results and one false-positive result were generated; these were generated by three separate laboratories. Both false-negative results were obtained with tests performed on specimens with the lowest concentration (1.2 × 104 genomic equivalents/mL). In addition, all 18 participants from Beijing achieved 100% sensitivity and 100% specificity. Overall, we conclude that the majority of the laboratories evaluated have reliable diagnostic capacities for the detection of measles virus. PMID:26244795

External Quality Assessment for the Detection of Measles Virus by Reverse Transcription-PCR Using Armored RNA.

PubMed

Zhang, Dong; Sun, Yu; Jia, Tingting; Zhang, Lei; Wang, Guojing; Zhang, Rui; Zhang, Kuo; Lin, Guigao; Xie, Jiehong; Wang, Lunan; Li, Jinming

2015-01-01

In recent years, nucleic acid tests for detection of measles virus RNA have been widely applied in laboratories belonging to the measles surveillance system of China. An external quality assessment program was established by the National Center for Clinical Laboratories to evaluate the performance of nucleic acid tests for measles virus. The external quality assessment panel, which consisted of 10 specimens, was prepared using armored RNAs, complex of noninfectious MS2 bacteriophage coat proteins encapsulated RNA of measles virus, as measles virus surrogate controls. Conserved sequences amplified from a circulating measles virus strain or from a vaccine strain were encapsulated into these armored RNAs. Forty-one participating laboratories from 15 provinces, municipalities, or autonomous regions that currently conduct molecular detection of measles virus enrolled in the external quality assessment program, including 40 measles surveillance system laboratories and one diagnostic reagent manufacturer. Forty laboratories used commercial reverse transcription-quantitative PCR kits, with only one laboratory applying a conventional PCR method developed in-house. The results indicated that most of the participants (38/41, 92.7%) were able to accurately detect the panel with 100% sensitivity and 100% specificity. Although a wide range of commercially available kits for nucleic acid extraction and reverse transcription polymerase chain reaction were used by the participants, only two false-negative results and one false-positive result were generated; these were generated by three separate laboratories. Both false-negative results were obtained with tests performed on specimens with the lowest concentration (1.2 × 104 genomic equivalents/mL). In addition, all 18 participants from Beijing achieved 100% sensitivity and 100% specificity. Overall, we conclude that the majority of the laboratories evaluated have reliable diagnostic capacities for the detection of measles virus.

Oxidative stress and food supplementation with antioxidants in therapy dogs.

PubMed

Sechi, Sara; Fiore, Filippo; Chiavolelli, Francesca; Dimauro, Corrado; Nudda, Anna; Cocco, Raffaella

2017-07-01

The objective of this study was to evaluate the ability of a long-term antioxidant-supplemented diet to regulate the oxidative stress and general health status of dogs involved in animal-assisted intervention (AAI) programs. Oxidative stress is a consequence of the accumulation of reactive oxygen species (ROS). Exercise-induced oxidative stress can increase muscle fatigue and fiber damage and eventually leads to impairment of the immune system. A randomized, placebo-controlled, crossover clinical evaluation was conducted with 11 healthy therapy dogs: 6 females and 5 males of different breeds and with a mean age of 2.7 ± 0.8 y (mean ± SEM). The dogs were divided into 2 groups, 1 fed a high quality commercial diet without antioxidants (CD) and the other a high quality commercial diet supplemented with antioxidants (SD) for 18 wk. After the first 18 wk, metabolic parameters, reactive oxygen metabolite-derivatives (d-ROMs), and biological antioxidant potential (BAP) levels were monitored and showed a significant reduction of d-ROMs, triglycerides, and creatinine values in the SD group ( P < 0.05) and a significant increase in amylase values in the CD group ( P < 0.01). At the end of this period, groups were crossed over and fed for another 18 wk. A significant decrease in amylase and glutamate pyruvate transaminase (GPT) values was observed in the CD and SD group, respectively ( P < 0.05). In conclusion, a controlled, balanced antioxidant diet may be a valid approach to restoring good cell metabolism and neutralizing excess free radicals in therapy dogs.

A short term quality control tool for biodegradable microspheres.

PubMed

D'Souza, Susan; Faraj, Jabar A; Dorati, Rossella; DeLuca, Patrick P

2014-06-01

Accelerated in vitro release testing methodology has been developed as an indicator of product performance to be used as a discriminatory quality control (QC) technique for the release of clinical and commercial batches of biodegradable microspheres. While product performance of biodegradable microspheres can be verified by in vivo and/or in vitro experiments, such evaluation can be particularly challenging because of slow polymer degradation, resulting in extended study times, labor, and expense. Three batches of Leuprolide poly(lactic-co-glycolic acid) (PLGA) microspheres having varying morphology (process variants having different particle size and specific surface area) were manufactured by the solvent extraction/evaporation technique. Tests involving in vitro release, polymer degradation and hydration of the microspheres were performed on the three batches at 55°C. In vitro peptide release at 55°C was analyzed using a previously derived modification of the Weibull function termed the modified Weibull equation (MWE). Experimental observations and data analysis confirm excellent reproducibility studies within and between batches of the microsphere formulations demonstrating the predictability of the accelerated experiments at 55°C. The accelerated test method was also successfully able to distinguish the in vitro product performance between the three batches having varying morphology (process variants), indicating that it is a suitable QC tool to discriminate product or process variants in clinical or commercial batches of microspheres. Additionally, data analysis utilized the MWE to further quantify the differences obtained from the accelerated in vitro product performance test between process variants, thereby enhancing the discriminatory power of the accelerated methodology at 55°C.

Oxidative stress and food supplementation with antioxidants in therapy dogs

PubMed Central

Sechi, Sara; Fiore, Filippo; Chiavolelli, Francesca; Dimauro, Corrado; Nudda, Anna; Cocco, Raffaella

2017-01-01

The objective of this study was to evaluate the ability of a long-term antioxidant-supplemented diet to regulate the oxidative stress and general health status of dogs involved in animal-assisted intervention (AAI) programs. Oxidative stress is a consequence of the accumulation of reactive oxygen species (ROS). Exercise-induced oxidative stress can increase muscle fatigue and fiber damage and eventually leads to impairment of the immune system. A randomized, placebo-controlled, crossover clinical evaluation was conducted with 11 healthy therapy dogs: 6 females and 5 males of different breeds and with a mean age of 2.7 ± 0.8 y (mean ± SEM). The dogs were divided into 2 groups, 1 fed a high quality commercial diet without antioxidants (CD) and the other a high quality commercial diet supplemented with antioxidants (SD) for 18 wk. After the first 18 wk, metabolic parameters, reactive oxygen metabolite-derivatives (d-ROMs), and biological antioxidant potential (BAP) levels were monitored and showed a significant reduction of d-ROMs, triglycerides, and creatinine values in the SD group (P < 0.05) and a significant increase in amylase values in the CD group (P < 0.01). At the end of this period, groups were crossed over and fed for another 18 wk. A significant decrease in amylase and glutamate pyruvate transaminase (GPT) values was observed in the CD and SD group, respectively (P < 0.05). In conclusion, a controlled, balanced antioxidant diet may be a valid approach to restoring good cell metabolism and neutralizing excess free radicals in therapy dogs. PMID:28725111

32 CFR 861.2 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Department of Defense Commercial Air Transportation Quality and Safety Review Program, charges the Commander... collectively referred to as “air carriers”) providing air transportation and operational support services to... Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT DEPARTMENT OF DEFENSE COMMERCIAL AIR...

Quality of Water from Shallow Wells in Urban Residential and Light Commercial Areas in Lafayette Parish, Louisiana, 2001 through 2002

USGS Publications Warehouse

Fendick, Robert B.; Tollett, Roland W.

2004-01-01

In 2001-02, the U.S. Geological Survey installed and sampled 28 shallow wells in urban residential and light commercial areas in Lafayette Parish, Louisiana, for a land-use study in the Acadian-Pontchartrain Study Unit of the National Water-Quality Assessment (NAWQA) Program. The wells were installed in the Chicot aquifer system, the primary source of water for irrigation and public-water supplies in southwestern Louisiana. The purpose of this report is to describe the quality of water from the 28 shallow wells and to relate that water quality to natural factors and to human activities. Ground-water samples were analyzed for general ground-water properties and about 240 water-quality contituents, including dissolved solids, major inorganic ions, trace elements, nutrients, dissolved organic carbon (DOC), radon, chlorofluorocarbons, selected stable isotopes, pesticides, pesticide degradation products, and volatile organic compounds (VOC's).

Building Energy Management Open Source Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rahman, Saifur

Funded by the U.S. Department of Energy in November 2013, a Building Energy Management Open Source Software (BEMOSS) platform was engineered to improve sensing and control of equipment in small- and medium-sized commercial buildings. According to the Energy Information Administration (EIA), small- (5,000 square feet or smaller) and medium-sized (between 5,001 to 50,000 square feet) commercial buildings constitute about 95% of all commercial buildings in the U.S. These buildings typically do not have Building Automation Systems (BAS) to monitor and control building operation. While commercial BAS solutions exist, including those from Siemens, Honeywell, Johnsons Controls and many more, they aremore » not cost effective in the context of small- and medium-sized commercial buildings, and typically work with specific controller products from the same company. BEMOSS targets small and medium-sized commercial buildings to address this gap.« less

The Joint Agency Commercial Imagery Evaluation Team and Product Characterization Approach

NASA Technical Reports Server (NTRS)

Zanoni, Vicki; Pagnutti, Mary; Ryan, Robert E.; Snyder, Greg; Lehman, William; Roylance, Spencer

2003-01-01

The Joint Agency Commercial Imagery Evaluation (JACIE) team is a collaborative interagency group focused on the characterization of commercial remote sensing data products. The team members - the National Aeronautics and Space Administration (NASA), the National Imagery and Mapping Agency (NIMA), and the U.S. Geological Survey (USGS) - each have a vested interest in the purchase and use of commercial imagery to support government research and operational applications. For both research and applications, commercial products must be well characterized for precision, accuracy, and repeatability. Since commercial systems are built and operated with no government insight or oversight, the JACIE team provides an independent product characterization of delivered image and image-derived end products. End product characterization differs from the systems calibration approach that is typically used with government systems, where detailed system design information is available. The product characterization approach addresses three primary areas of product performance: geopositional accuracy, image quality, and radiometric accuracy. The JACIE team utilizes well-characterized test sites to support characterization activities. To characterize geopositional accuracy, the team utilizes sites containing several "photo-identifiable" targets and compares their precisely known locations with those defined by the commercial image product. In the area of image quality, spatial response is characterized using edge targets and pulse targets to measure edge response and to estimate image modulation transfer function. Additionally, imagery is also characterized using the National Imagery Interpretability Rating Scale, a means of quantifying the ability to identify certain targets (e.g., rail-cars, airplanes) within an image product. Radiometric accuracy is characterized using reflectance-based vicarious calibration methods at several uniform sites. Each JACIE agency performs an aspect of product characterization based on its area of expertise, thus minimizing duplication of effort. The JACIE team collaborated to perform comprehensive characterization of products from Space Imaging Inc.'s IKONOS satellite and from DigitalGlobe's QuickBird satellite and is currently characterizing products from OrbImage s OrbView-3. JACIE assessments have resulted in several improvements to commercial image product quality and have enhanced working relationships between government and industry. Assessment results are presented at an annual JACIE High Spatial Resolution Commercial Imagery Workshop.

Machine Vision-Based Measurement Systems for Fruit and Vegetable Quality Control in Postharvest.

PubMed

Blasco, José; Munera, Sandra; Aleixos, Nuria; Cubero, Sergio; Molto, Enrique

Individual items of any agricultural commodity are different from each other in terms of colour, shape or size. Furthermore, as they are living thing, they change their quality attributes over time, thereby making the development of accurate automatic inspection machines a challenging task. Machine vision-based systems and new optical technologies make it feasible to create non-destructive control and monitoring tools for quality assessment to ensure adequate accomplishment of food standards. Such systems are much faster than any manual non-destructive examination of fruit and vegetable quality, thus allowing the whole production to be inspected with objective and repeatable criteria. Moreover, current technology makes it possible to inspect the fruit in spectral ranges beyond the sensibility of the human eye, for instance in the ultraviolet and near-infrared regions. Machine vision-based applications require the use of multiple technologies and knowledge, ranging from those related to image acquisition (illumination, cameras, etc.) to the development of algorithms for spectral image analysis. Machine vision-based systems for inspecting fruit and vegetables are targeted towards different purposes, from in-line sorting into commercial categories to the detection of contaminants or the distribution of specific chemical compounds on the product's surface. This chapter summarises the current state of the art in these techniques, starting with systems based on colour images for the inspection of conventional colour, shape or external defects and then goes on to consider recent developments in spectral image analysis for internal quality assessment or contaminant detection.

Machine vision system for measuring conifer seedling morphology

NASA Astrophysics Data System (ADS)

Rigney, Michael P.; Kranzler, Glenn A.

1995-01-01

A PC-based machine vision system providing rapid measurement of bare-root tree seedling morphological features has been designed. The system uses backlighting and a 2048-pixel line- scan camera to acquire images with transverse resolutions as high as 0.05 mm for precise measurement of stem diameter. Individual seedlings are manually loaded on a conveyor belt and inspected by the vision system in less than 0.25 seconds. Designed for quality control and morphological data acquisition by nursery personnel, the system provides a user-friendly, menu-driven graphical interface. The system automatically locates the seedling root collar and measures stem diameter, shoot height, sturdiness ratio, root mass length, projected shoot and root area, shoot-root area ratio, and percent fine roots. Sample statistics are computed for each measured feature. Measurements for each seedling may be stored for later analysis. Feature measurements may be compared with multi-class quality criteria to determine sample quality or to perform multi-class sorting. Statistical summary and classification reports may be printed to facilitate the communication of quality concerns with grading personnel. Tests were conducted at a commercial forest nursery to evaluate measurement precision. Four quality control personnel measured root collar diameter, stem height, and root mass length on each of 200 conifer seedlings. The same seedlings were inspected four times by the machine vision system. Machine stem diameter measurement precision was four times greater than that of manual measurements. Machine and manual measurements had comparable precision for shoot height and root mass length.

QTL mapping of fruit mineral contents provides new chances for molecular breeding of tomato nutritional traits.

PubMed

Capel, Carmen; Yuste-Lisbona, Fernando J; López-Casado, Gloria; Angosto, Trinidad; Heredia, Antonio; Cuartero, Jesús; Fernández-Muñoz, Rafael; Lozano, Rafael; Capel, Juan

2017-05-01

Agronomical characterization of a RIL population for fruit mineral contents allowed for the identification of QTL controlling these fruit quality traits, flanked by co-dominant markers useful for marker-assisted breeding. Tomato quality is a multi-variant attribute directly depending on fruit chemical composition, which in turn determines the benefits of tomato consumption for human health. Commercially available tomato varieties possess limited variability in fruit quality traits. Wild species, such as Solanum pimpinellifolium, could provide different nutritional advantages and can be used for tomato breeding to improve overall fruit quality. Determining the genetic basis of the inheritance of all the traits that contribute to tomato fruit quality will increase the efficiency of the breeding program necessary to take advantage of the wild species variability. A high-density linkage map has been constructed from a recombinant inbred line (RIL) population derived from a cross between tomato Solanum lycopersicum and the wild-relative species S. pimpinellifolium. The RIL population was evaluated for fruit mineral contents during three consecutive growing seasons. The data obtained allowed for the identification of main QTL and novel epistatic interaction among QTL controlling fruit mineral contents on the basis of a multiple-environment analysis. Most of the QTL were flanked by candidate genes providing valuable information for both tomato breeding for new varieties with novel nutritional properties and the starting point to identify the genes underlying these QTL, which will help to reveal the genetic basis of tomato fruit nutritional properties.

75 FR 70203 - Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From the...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-17

... cards, and other commercial printing applications requiring high quality print graphics. Specifically... Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From the People's Republic of China... on certain coated paper suitable for high-quality print graphics using sheet-fed presses (``coated...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Traynor, G.W.; Talbott, J.M.; Moses, D.O.

Building ventilation consumes about 5.8 exajoules of energy each year in the US The annual cost of this energy, used for commercial building fans (1.6 exajoules) and the heating and cooling of outside air (4.2 exajoules), is about $US 33 billion per year. Energy conservation measures that reduce heating and cooling season ventilation rates 15 to 35% in commercial and residential buildings can result in a national savings of about 0.6 to 1.5 exajoules ($US 3-8 billion) per year assuming no reduction of commercial building fan energy use. The most significant adverse environmental impact of reduced ventilation and infiltration ismore » the potential degradation of the buildings indoor air quality. Potential benefits to the US from the implementation of sound indoor air quality and building ventilation reduction policies include reduced building-sector energy consumption; reduced indoor, outdoor, and global air pollution; reduced product costs; reduced worker absenteeism; reduced health care costs; reduced litigation; increased worker well-being and productivity; and increased product quality and competitiveness.« less

Effect of psychrotrophic post-pasteurization contamination of the keeping quality at 11 and 5 degrees C of HTST-pasteurized milk in the UK.

PubMed

Schröder, M J; Cousins, C M; McKinnon, C H

1982-11-01

The keeping quality of commercial HTST-pasteurized milk and laboratory pasteurized milk from a common bulk raw supply has been investigated for 5 dairies. Spoilage occurred at levels of total bacterial counts around 10(7) colony forming units/ml, but with a slightly higher off-flavour threshold for the commercial milks than the laboratory pasteurized milks. The predominant microflora at spoilage and the type of off-flavour produced differed between the 2 types of milk. Raising the storage temperature from 5 to 11 degrees C caused a slight shift in the spoilage microflora and led to an average reduction in the shelf life of the laboratory pasteurized milk from 28 to 6 d and of the commercial pasteurized milk from 13 to 5 d. Changes in the level of post-pasteurization contamination (PPC) were reflected in changes in keeping quality, particularly at 5 degrees C. However, the greatest improvements were found in the absence of PPC.

Metabolomics driven analysis of artichoke leaf and its commercial products via UHPLC-q-TOF-MS and chemometrics.

PubMed

Farag, Mohamed A; El-Ahmady, Sherweit H; Elian, Fatma S; Wessjohann, Ludger A

2013-11-01

The demand to develop efficient and reliable analytical methods for the quality control of herbal medicines and nutraceuticals is on the rise, together with an increase in the legal requirements for safe and consistent levels of active principles. Here, we describe an ultra-high performance liquid chromatography method (UHPLC) coupled with quadrupole high resolution time of flight mass spectrometry (qTOF-MS) analysis for the comprehensive measurement of metabolites from three Cynara scolymus (artichoke) cultivars: American Green Globe, French Hyrious, and Egyptian Baladi. Under optimized conditions, 50 metabolites were simultaneously quantified and identified including: eight caffeic acid derivatives, six saponins, 12 flavonoids and 10 fatty acids. Principal component analysis (PCA) was used to define both similarities and differences among the three artichoke leaf cultivars. In addition, batches from seven commercially available artichoke market products were analysed and showed variable quality, particularly in caffeic acid derivatives, flavonoid and fatty acid contents. PCA analysis was able to discriminate between various preparations, including differentiation between various batches from the same supplier. To the best of our knowledge, this study provides the first approach utilizing UHPLC-MS based metabolite fingerprinting to reveal secondary metabolite compositional differences in artichoke leaf extracts. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of commercial mineral-based additives on composting and compost quality.

PubMed

Himanen, M; Hänninen, K

2009-08-01

The effectiveness of two commercial additives meant to improve the composting process was studied in a laboratory-scale experiment. Improver A (sulphates and oxides of iron, magnesium, manganese, and zinc mixed with clay) and B (mixture of calcium hydroxide, peroxide, and oxide) were added to source-separated biowaste:peat mixture (1:1, v/v) in proportions recommended by the producers. The composting process (T, emissions of CO(2), NH(3), and CH(4)) and the quality of the compost (pH, conductivity, C/N ratio, water-soluble NH(4)-N and NO(3)-N, water- and NaOH-soluble low-weight carboxylic acids, nutrients, heavy metals and phytotoxicity to Lepidium sarivum) were monitored during one year. Compared with the control, the addition of improver B increased pH by two units, led to an earlier elimination of water-soluble ammonia, an increase in nitrates, a 10-fold increase in concentrations of acetic acid, and shortened phytotoxicity period by half; as negative aspect it led to volatilization of ammonia. The addition of improver A led to a longer thermophilic stage by one week and lower concentrations of low-weight carboxylic acids (both water- and NaOH-extractable) with formic and acetic of similar amounts, however, most of the aspects claimed by the improver's producer were not confirmed in this trial.

Improvement in botanical standardization of commercial freeze-dried herbal extracts by using the combination of antioxidant capacity and constituent marker concentrations.

PubMed

Ninfali, Paolino; Gennari, Lorenzo; Biagiotti, Enrica; Cangi, Francesca; Mattoli, Luisa; Maidecchi, Anna

2009-01-01

Botanical extracts are standardized to > or = 1 marker compounds (MCs). This standardization provides a certain level of quality control, but not complete quality assurance. Thus, industries are looking for other satisfactory systems to improve standardization. This study focuses on the standardization of herbal medicines by combining 2 parameters: the concentration of the MC and antioxidant capacity. Antioxidant capacity was determined with the oxygen radical absorbance capacity (ORAC) method and the concentrations of the MCs, by high-performance liquid chromatography. Total phenols were also determined by the Folin-Ciocolteau method. The ORAC values, expressed as micromol Trolox equivalents/100 g (ORAC %), of 12 commercial herbal extracts were related to the ORAC values of the respective pure MCs at the concentrations at which the MCs occur in products (ORAC-MC %). The ORAC % values of 11 extracts were higher than those of the respective MCs and the ratios ORAC-MC %/ORAC % ranged from 0.007 to 0.7, whereas in the case of Olea europaea leaves, the same ratio was 1.36. The ORAC parameters and their ratios, as well as the linear relationship between ORAC-MC % and ORAC %, are described and discussed as tools for improving the standardization of herbal products and detecting modifications due to herb processing and storage.

Antimicrobial peptides and plant disease control.

PubMed

Montesinos, Emilio

2007-05-01

Several diseases caused by viruses, bacteria and fungi affect plant crops, resulting in losses and decreasing the quality and safety of agricultural products. Plant disease control relies mainly on chemical pesticides that are currently subject to strong restrictions and regulatory requirements. Antimicrobial peptides are interesting compounds in plant health because there is a need for new products in plant protection that fit into the new regulations. Living organisms secrete a wide range of antimicrobial peptides produced through ribosomal (defensins and small bacteriocins) or non-ribosomal synthesis (peptaibols, cyclopeptides and pseudopeptides). Several antimicrobial peptides are the basis for the design of new synthetic analogues, have been expressed in transgenic plants to confer disease protection or are secreted by microorganisms that are active ingredients of commercial biopesticides.

Advances in vaccine research against economically important viral diseases of food animals: Infectious bursal disease virus.

PubMed

Jackwood, Daral J

2017-07-01

Numerous reviews have been published on infectious bursal disease (IBD) and infectious bursal disease virus (IBDV). Many high quality vaccines are commercially available for the control of IBD that, when used correctly, provide solid protection against infection and disease caused by IBDV. Viruses are not static however; they continue to evolve and vaccines need to keep pace with them. The evolution of IBDV has resulted in very virulent strains and new antigenic types of the virus. This review will discuss some of the limitations associated with existing vaccines, potential solutions to these problems and advances in new vaccines for the control of IBD. Copyright © 2016 Elsevier B.V. All rights reserved.

Information technology and medical missteps: evidence from a randomized trial.

PubMed

Javitt, Jonathan C; Rebitzer, James B; Reisman, Lonny

2008-05-01

We analyze the effect of a decision support tool designed to help physicians detect and correct medical "missteps". The data comes from a randomized trial of the technology on a population of commercial HMO patients. The key findings are that the new information technology lowers average charges by 6% relative to the control group. This reduction in resource utilization was the result of reduced in-patient charges (and associated professional charges) for the most costly patients. The rate at which identified issues were resolved was generally higher in the study group than in the control group, suggesting the possibility of improvements in care quality along measured dimensions and enhanced diffusion of new protocols based on new clinical evidence.

Direct Growth of Graphene on Silicon by Metal-Free Chemical Vapor Deposition

NASA Astrophysics Data System (ADS)

Tai, Lixuan; Zhu, Daming; Liu, Xing; Yang, Tieying; Wang, Lei; Wang, Rui; Jiang, Sheng; Chen, Zhenhua; Xu, Zhongmin; Li, Xiaolong

2018-06-01

The metal-free synthesis of graphene on single-crystal silicon substrates, the most common commercial semiconductor, is of paramount significance for many technological applications. In this work, we report the growth of graphene directly on an upside-down placed, single-crystal silicon substrate using metal-free, ambient-pressure chemical vapor deposition. By controlling the growth temperature, in-plane propagation, edge-propagation, and core-propagation, the process of graphene growth on silicon can be identified. This process produces atomically flat monolayer or bilayer graphene domains, concave bilayer graphene domains, and bulging few-layer graphene domains. This work would be a significant step toward the synthesis of large-area and layer-controlled, high-quality graphene on single-crystal silicon substrates. [Figure not available: see fulltext.

A systematic review of randomized controlled trials for prevention or treatment of atopic dermatitis in dogs: 2008-2011 update.

PubMed

Olivry, Thierry; Bizikova, Petra

2013-02-01

The management of atopic dermatitis (AD) in dogs relies mainly on the use of interventions to reduce pruritus and skin lesions. To provide a critical analysis of recent clinical trials reporting the efficacy and safety of interventions for canine AD. Systematic review of randomized controlled trials (RCTs) published, presented or completed between 2008 and 2011, which enrolled dogs with AD. The search was done using electronic databases, reviewing published meeting abstracts and sending queries to professional email lists. Trials reporting the efficacy of interventions aimed at treating, preventing or reducing glucocorticoid usage in atopic dogs were selected. Twenty-one RCTs were included. We found further moderate-quality evidence of efficacy and safety of oral glucocorticoids and ciclosporin for treatment of canine AD. There was additional moderate-quality evidence of the efficacy of a topical glucocorticoid spray containing hydrocortisone aceponate. Low-quality evidence was found for the efficacy and safety of injectable recombinant interferons, a budesonide leave-on conditioner, a ciclosporin topical nano-emulsion and oral fexofenadine. There is low-quality evidence of efficacy of oral masitinib, with a need for monitoring for protein-losing nephropathy. Finally, we uncovered low-quality evidence of efficacy of a commercial diet as a glucocorticoid-sparing intervention and of a glucocorticoid spray as a flare-delaying measure. Very low-quality evidence was found for the efficacy of other interventions. Topical or oral glucocorticoids and oral ciclosporin remain the interventions with highest evidence for efficacy and relative safety for treatment of canine AD. © 2013 The Authors. Veterinary Dermatology © 2013 ESVD and ACVD.

The effect of gamma irradiation on the stability and hygienic quality of semi-dried Pacific saury ( Cololabis seira) flesh

NASA Astrophysics Data System (ADS)

Lee, Ju.-Woon; Cho, Kyung.-Hwan; Yook, Hong.-Sun; Jo, Cheorun; Kim, Dong.-Ho; Byun, Myung.-Woo

2002-07-01

This study was carried out to investigate the effects of gamma irradiation on the improvement of hygienic quality and the extension of shelf life of Kwamegi prepared from semi-dried Pacific saury ( Cololabis seira) flesh. Commercial Kwamegi was purchased from a domestic market, vacuum-packaged, and irradiated to doses of 0, 3, 5, 7 or 10 kGy. Non-irradiated Kwamegi rapidly deteriorated during storage at 5°C, and some bacteria presumed as Salmonella and/or Shigella species were detected using selective medium. However, the total viable cells and presumptive pathogens were reduced with increased radiation dose, and a dose level of 7-10 kGy was considered to be an optimum and effective dose for the preservation of Kwamegi. Thiobarbituric acid values did not differ, regardless of irradiation dose and storage time. Sensory evaluation results were not different in all samples immediately after irradiation. After 60-day storage, the sensory quality of irradiated Kwamegi was adequate; however the quality of the control deteriorated.

WELDSMART: A vision-based expert system for quality control

NASA Technical Reports Server (NTRS)

Andersen, Kristinn; Barnett, Robert Joel; Springfield, James F.; Cook, George E.

1992-01-01

This work was aimed at exploring means for utilizing computer technology in quality inspection and evaluation. Inspection of metallic welds was selected as the main application for this development and primary emphasis was placed on visual inspection, as opposed to other inspection methods, such as radiographic techniques. Emphasis was placed on methodologies with the potential for use in real-time quality control systems. Because quality evaluation is somewhat subjective, despite various efforts to classify discontinuities and standardize inspection methods, the task of using a computer for both inspection and evaluation was not trivial. The work started out with a review of the various inspection techniques that are used for quality control in welding. Among other observations from this review was the finding that most weld defects result in abnormalities that may be seen by visual inspection. This supports the approach of emphasizing visual inspection for this work. Quality control consists of two phases: (1) identification of weld discontinuities (some of which may be severe enough to be classified as defects), and (2) assessment or evaluation of the weld based on the observed discontinuities. Usually the latter phase results in a pass/fail judgement for the inspected piece. It is the conclusion of this work that the first of the above tasks, identification of discontinuities, is the most challenging one. It calls for sophisticated image processing and image analysis techniques, and frequently ad hoc methods have to be developed to identify specific features in the weld image. The difficulty of this task is generally not due to limited computing power. In most cases it was found that a modest personal computer or workstation could carry out most computations in a reasonably short time period. Rather, the algorithms and methods necessary for identifying weld discontinuities were in some cases limited. The fact that specific techniques were finally developed and successfully demosntrated to work illustrates that the general approach taken here appears to be promising for commercial development of computerized quality inspection systems. Inspection based on these techniques may be used to supplement or substitute more elaborate inspection methods, such as x-ray inspections.

Virtual Reality Therapy for Adults Post-Stroke: A Systematic Review and Meta-Analysis Exploring Virtual Environments and Commercial Games in Therapy

PubMed Central

Lohse, Keith R.; Hilderman, Courtney G. E.; Cheung, Katharine L.; Tatla, Sandy; Van der Loos, H. F. Machiel

2014-01-01

Background The objective of this analysis was to systematically review the evidence for virtual reality (VR) therapy in an adult post-stroke population in both custom built virtual environments (VE) and commercially available gaming systems (CG). Methods MEDLINE, CINAHL, EMBASE, ERIC, PSYCInfo, DARE, PEDro, Cochrane Central Register of Controlled Trials, and Cochrane Database of Systematic Reviews were systematically searched from the earliest available date until April 4, 2013. Controlled trials that compared VR to conventional therapy were included. Population criteria included adults (>18) post-stroke, excluding children, cerebral palsy, and other neurological disorders. Included studies were reported in English. Quality of studies was assessed with the Physiotherapy Evidence Database Scale (PEDro). Results Twenty-six studies met the inclusion criteria. For body function outcomes, there was a significant benefit of VR therapy compared to conventional therapy controls, G = 0.48, 95% CI = [0.27, 0.70], and no significant difference between VE and CG interventions (P = 0.38). For activity outcomes, there was a significant benefit of VR therapy, G = 0.58, 95% CI = [0.32, 0.85], and no significant difference between VE and CG interventions (P = 0.66). For participation outcomes, the overall effect size was G = 0.56, 95% CI = [0.02, 1.10]. All participation outcomes came from VE studies. Discussion VR rehabilitation moderately improves outcomes compared to conventional therapy in adults post-stroke. Current CG interventions have been too few and too small to assess potential benefits of CG. Future research in this area should aim to clearly define conventional therapy, report on participation measures, consider motivational components of therapy, and investigate commercially available systems in larger RCTs. Trial Registration Prospero CRD42013004338 PMID:24681826

Virtual reality therapy for adults post-stroke: a systematic review and meta-analysis exploring virtual environments and commercial games in therapy.

PubMed

Lohse, Keith R; Hilderman, Courtney G E; Cheung, Katharine L; Tatla, Sandy; Van der Loos, H F Machiel

2014-01-01

The objective of this analysis was to systematically review the evidence for virtual reality (VR) therapy in an adult post-stroke population in both custom built virtual environments (VE) and commercially available gaming systems (CG). MEDLINE, CINAHL, EMBASE, ERIC, PSYCInfo, DARE, PEDro, Cochrane Central Register of Controlled Trials, and Cochrane Database of Systematic Reviews were systematically searched from the earliest available date until April 4, 2013. Controlled trials that compared VR to conventional therapy were included. Population criteria included adults (>18) post-stroke, excluding children, cerebral palsy, and other neurological disorders. Included studies were reported in English. Quality of studies was assessed with the Physiotherapy Evidence Database Scale (PEDro). Twenty-six studies met the inclusion criteria. For body function outcomes, there was a significant benefit of VR therapy compared to conventional therapy controls, G = 0.48, 95% CI = [0.27, 0.70], and no significant difference between VE and CG interventions (P = 0.38). For activity outcomes, there was a significant benefit of VR therapy, G = 0.58, 95% CI = [0.32, 0.85], and no significant difference between VE and CG interventions (P = 0.66). For participation outcomes, the overall effect size was G = 0.56, 95% CI = [0.02, 1.10]. All participation outcomes came from VE studies. VR rehabilitation moderately improves outcomes compared to conventional therapy in adults post-stroke. Current CG interventions have been too few and too small to assess potential benefits of CG. Future research in this area should aim to clearly define conventional therapy, report on participation measures, consider motivational components of therapy, and investigate commercially available systems in larger RCTs. Prospero CRD42013004338.

Quality-related enzymes in fruit and vegetable products: effects of novel food processing technologies, part 1: high-pressure processing.

PubMed

Terefe, Netsanet Shiferaw; Buckow, Roman; Versteeg, Cornelis

2014-01-01

The activity of endogenous deteriorative enzymes together with microbial growth (with associated enzymatic activity) and/or other non-enzymatic (usually oxidative) reactions considerably shorten the shelf life of fruits and vegetable products. Thermal processing is commonly used by the food industry for enzyme and microbial inactivation and is generally effective in this regard. However, thermal processing may cause undesirable changes in product's sensory as well as nutritional attributes. Over the last 20 years, there has been a great deal of interest shown by both the food industry and academia in exploring alternative food processing technologies that use minimal heat and/or preservatives. One of the technologies that have been investigated in this context is high-pressure processing (HPP). This review deals with HPP focusing on its effectiveness for controlling quality-degrading enzymes in horticultural products. The scientific literature on the effects of HPP on plant enzymes, mechanism of action, and intrinsic and extrinsic factors that influence the effectiveness of HPP for controlling plant enzymes is critically reviewed. HPP inactivates vegetative microbial cells at ambient temperature conditions, resulting in a very high retention of the nutritional and sensory characteristics of the fresh product. Enzymes such as polyphenol oxidase (PPO), peroxidase (POD), and pectin methylesterase (PME) are highly resistant to HPP and are at most partially inactivated under commercially feasible conditions, although their sensitivity towards pressure depends on their origin as well as their environment. Polygalacturonase (PG) and lipoxygenase (LOX) on the other hand are relatively more pressure sensitive and can be substantially inactivated by HPP at commercially feasible conditions. The retention and activation of enzymes such as PME by HPP can be beneficially used for improving the texture and other quality attributes of processed horticultural products as well as for creating novel structures that are not feasible with thermal processing.

Reprocessing Close Range Terrestrial and Uav Photogrammetric Projects with the Dbat Toolbox for Independent Verification and Quality Control

NASA Astrophysics Data System (ADS)

Murtiyoso, A.; Grussenmeyer, P.; Börlin, N.

2017-11-01

Photogrammetry has recently seen a rapid increase in many applications, thanks to developments in computing power and algorithms. Furthermore with the democratisation of UAVs (Unmanned Aerial Vehicles), close range photogrammetry has seen more and more use due to the easier capability to acquire aerial close range images. In terms of photogrammetric processing, many commercial software solutions exist in the market that offer results from user-friendly environments. However, in most commercial solutions, a black-box approach to photogrammetric calculations is often used. This is understandable in light of the proprietary nature of the algorithms, but it may pose a problem if the results need to be validated in an independent manner. In this paper, the Damped Bundle Adjustment Toolbox (DBAT) developed for Matlab was used to reprocess some photogrammetric projects that were processed using the commercial software Agisoft Photoscan. Several scenarios were experimented on in order to see the performance of DBAT in reprocessing terrestrial and UAV close range photogrammetric projects in several configurations of self-calibration setting. Results show that DBAT managed to reprocess PS projects and generate metrics which can be useful for project verification.

Common Data Acquisition Systems (DAS) Software Development for Rocket Propulsion Test (RPT) Test Facilities

NASA Technical Reports Server (NTRS)

Hebert, Phillip W., Sr.; Davis, Dawn M.; Turowski, Mark P.; Holladay, Wendy T.; Hughes, Mark S.

2012-01-01

The advent of the commercial space launch industry and NASA's more recent resumption of operation of Stennis Space Center's large test facilities after thirty years of contractor control resulted in a need for a non-proprietary data acquisition systems (DAS) software to support government and commercial testing. The software is designed for modularity and adaptability to minimize the software development effort for current and future data systems. An additional benefit of the software's architecture is its ability to easily migrate to other testing facilities thus providing future commonality across Stennis. Adapting the software to other Rocket Propulsion Test (RPT) Centers such as MSFC, White Sands, and Plumbrook Station would provide additional commonality and help reduce testing costs for NASA. Ultimately, the software provides the government with unlimited rights and guarantees privacy of data to commercial entities. The project engaged all RPT Centers and NASA's Independent Verification & Validation facility to enhance product quality. The design consists of a translation layer which provides the transparency of the software application layers to underlying hardware regardless of test facility location and a flexible and easily accessible database. This presentation addresses system technical design, issues encountered, and the status of Stennis development and deployment.

Maize transformation technology development for commercial event generation.

PubMed

Que, Qiudeng; Elumalai, Sivamani; Li, Xianggan; Zhong, Heng; Nalapalli, Samson; Schweiner, Michael; Fei, Xiaoyin; Nuccio, Michael; Kelliher, Timothy; Gu, Weining; Chen, Zhongying; Chilton, Mary-Dell M

2014-01-01

Maize is an important food and feed crop in many countries. It is also one of the most important target crops for the application of biotechnology. Currently, there are more biotech traits available on the market in maize than in any other crop. Generation of transgenic events is a crucial step in the development of biotech traits. For commercial applications, a high throughput transformation system producing a large number of high quality events in an elite genetic background is highly desirable. There has been tremendous progress in Agrobacterium-mediated maize transformation since the publication of the Ishida et al. (1996) paper and the technology has been widely adopted for transgenic event production by many labs around the world. We will review general efforts in establishing efficient maize transformation technologies useful for transgenic event production in trait research and development. The review will also discuss transformation systems used for generating commercial maize trait events currently on the market. As the number of traits is increasing steadily and two or more modes of action are used to control key pests, new tools are needed to efficiently transform vectors containing multiple trait genes. We will review general guidelines for assembling binary vectors for commercial transformation. Approaches to increase transformation efficiency and gene expression of large gene stack vectors will be discussed. Finally, recent studies of targeted genome modification and transgene insertion using different site-directed nuclease technologies will be reviewed.

Maize transformation technology development for commercial event generation

PubMed Central

Que, Qiudeng; Elumalai, Sivamani; Li, Xianggan; Zhong, Heng; Nalapalli, Samson; Schweiner, Michael; Fei, Xiaoyin; Nuccio, Michael; Kelliher, Timothy; Gu, Weining; Chen, Zhongying; Chilton, Mary-Dell M.

2014-01-01

Maize is an important food and feed crop in many countries. It is also one of the most important target crops for the application of biotechnology. Currently, there are more biotech traits available on the market in maize than in any other crop. Generation of transgenic events is a crucial step in the development of biotech traits. For commercial applications, a high throughput transformation system producing a large number of high quality events in an elite genetic background is highly desirable. There has been tremendous progress in Agrobacterium-mediated maize transformation since the publication of the Ishida et al. (1996) paper and the technology has been widely adopted for transgenic event production by many labs around the world. We will review general efforts in establishing efficient maize transformation technologies useful for transgenic event production in trait research and development. The review will also discuss transformation systems used for generating commercial maize trait events currently on the market. As the number of traits is increasing steadily and two or more modes of action are used to control key pests, new tools are needed to efficiently transform vectors containing multiple trait genes. We will review general guidelines for assembling binary vectors for commercial transformation. Approaches to increase transformation efficiency and gene expression of large gene stack vectors will be discussed. Finally, recent studies of targeted genome modification and transgene insertion using different site-directed nuclease technologies will be reviewed. PMID:25140170

Impact of reduced mass of light commercial vehicles on fuel consumption, CO2 emissions, air quality, and socio-economic costs.

PubMed

Cecchel, S; Chindamo, D; Turrini, E; Carnevale, C; Cornacchia, G; Gadola, M; Panvini, A; Volta, M; Ferrario, D; Golimbioschi, R

2018-02-01

This study presents a modelling system to evaluate the impact of weight reduction in light commercial vehicles with diesel engines on air quality and greenhouse gas emissions. The PROPS model assesses the emissions of one vehicle in the aforementioned category and its corresponding reduced-weight version. The results serve as an input to the RIAT+ tool, an air quality integrated assessment modelling system. This paper applies the tools in a case study in the Lombardy region (Italy) and discusses the input data pre-processing, the PROPS-RIAT+ modelling system runs, and the results. Copyright © 2017 Elsevier B.V. All rights reserved.

Safety of ceftriaxone in paediatrics: a systematic review protocol.

PubMed

Zeng, Linan; Choonara, Imti; Zhang, Lingli; Xue, Song; Chen, Zhe; He, Miaomiao

2017-08-21

Ceftriaxone is widely used in children in the treatment of sepsis. However, concerns have been raised about the safety of ceftriaxone, especially in young children. The aim of this review is to systematically evaluate the safety of ceftriaxone in children of all age groups. MEDLINE, PubMed, Cochrane Central Register of Controlled Trials, EMBASE, CINAHL, International Pharmaceutical Abstracts and adverse drug reaction (ADR) monitoring systems will be systematically searched for randomised controlled trials (RCTs), cohort studies, case-control studies, cross-sectional studies, case series and case reports evaluating the safety of ceftriaxone in children. The Cochrane risk of bias tool, Newcastle-Ottawa and quality assessment tools developed by the National Institutes of Health will be used for quality assessment. Meta-analysis of the incidence of ADRs from RCTs and prospective studies will be done. Subgroup analyses will be performed for age and dosage regimen. Formal ethical approval is not required as no primary data are collected. This systematic review will be disseminated through a peer-reviewed publication and at conference meetings. CRD42017055428. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Monitoring industrial wastewater by online GC-MS with direct aqueous injection.

PubMed

Wortberg, M; Ziemer, W; Kugel, M; Müller, H; Neu, H-J

2006-03-01

An online GC-MS-system for automated monitoring of crude wastewater at a complex chemical production site is presented. The modular system is, in principal, based on commercial equipment, but utilizes a special, two-stage injector, which consists of a splitless vaporization chamber on top of a PTV injector filled with Tenax. This set-up enables direct injection of wastewater. Almost 140 volatile and semi-volatile compounds are calibrated down to 1 mg L(-1), which is sufficient for analysis of the influent of the wastewater-treatment plant. Two instruments analyze alternately, every 20 min, and the instrument cycle time is 40 min. The quantitative results are transferred to a database which is connected to a process-control system. Depending on the nature and concentration of a compound, an alarm can be generated and the wastewater stream can be diverted into an "off spec tank" if necessary. The GC-MS-system operates quasi-continuously with a system availability >98%. Data quality is automatically controlled in each run and by daily analysis of a quality-control sample. The development of a novel stacked PTV-PTV injector design to expand the range of analytes to selected basic compounds is described.

Methodology to estimate particulate matter emissions from certified commercial aircraft engines.

DOT National Transportation Integrated Search

2009-01-01

Today, about one-fourth of U.S. commercial service airports, : including 41 of the busiest 50, are either in nonattainment : or maintenance areas per the National Ambient : Air Quality Standards. U.S. aviation activity is forecasted : to triple by 20...

Red beet and betaine as ingredients in diets of rainbow trout (Oncorhynchus mykiss): effects on growth performance, nutrient retention and flesh quality.

PubMed

Pinedo-Gil, Julia; Tomás-Vidal, Ana; Jover-Cerdá, Miguel; Tomás-Almenar, Cristina; Sanz-Calvo, Miguel Ángel; Martín-Diana, Ana Belén

2017-12-01

The objective of the study was to evaluate the impact of different concentrations of dietary red beet and betaine on the growth performance and fish flesh quality of rainbow trout. Therefore, a control diet was compared with four diets in which two levels of red beet (14% and 28%) and betaine (0.9% and 1.63%) were incorporated in combination. The study was set up with an average body weight of 69 ± 2.2 g and finished when fish reached commercial weight (175-250 g) after 105 d. The impact of the diets was studied based on the growth performance, biometric indexes, proximal composition, protein and fat retention efficiencies and apparent nutrient digestibility by fish reared on a recirculation system. Further estimates were the effect of red beet and betaine on the flesh proximate composition and quality of the final product (water activity, colour, texture, thiobarbituric acid reactive substances and sensory characteristics). Results showed that inclusion of 14% red beet and 0.9% betaine did not affect growth, nutritive or biometric parameters and nutrient retention when compared with the control diet. However, higher levels of red beet and betaine had negative effects on growth and nutritive parameters. The tested ingredients enhanced quality parameters regardless of the concentration used. After feeding the red beet and betaine, fish flesh showed lower water activity and better textural and colour properties than the control and also a dose-dependent effect on lipid oxidation was observed.

Dietary Lecithin Supplementation Can Improve the Quality of the M. Longissimus thoracis

PubMed Central

D’Souza, Darryl N.; Blake, Bronwyn L.; Williams, Ian H.; Mullan, Bruce P.; Pethick, David W.; Dunshea, Frank R.

2015-01-01

Simple Summary Meat tenderness and texture can be influenced by the connective tissue content. Dietary lecithin offers a means of improving fat digestibility of pigs and reducing the connective tissue of pork. This feeding study confirmed that dietary lecithin decreased the chewiness and improved the fatty acid composition of pork without impacting on growth performance of pigs. Therefore, dietary lecithin supplementation has the potential to improve the quality attributes of pork. Abstract Forty crossbred (Large White × Landrace × Duroc) female pigs (16.4 kg ± 0.94 kg) were used to investigate the effect of dietary lecithin supplementation on growth performance and pork quality. Pigs were randomly allocated to a commercial diet containing either 0, 3, 15 or 75 g lecithin/kg of feed during the grower and finisher growth phase. Pork from pigs consuming the diets containing 15 g and 75 g lecithin/kg had lower hardness (P < 0.001) and chewiness (P < 0.01) values compared to the controls. Dietary lecithin supplementation at 75 g/kg significantly increased (P < 0.05) the linoleic acid and reduced (P < 0.05) the myristic acid levels of pork compared to the control and the 3 g/kg and 15 g/kg lecithin supplemented treatments. Pigs fed the 75 g/kg lecithin supplemented diet had lower plasma cholesterol (P < 0.05) at slaughter compared to pigs fed the control diet and the 3 g/kg and 15 g/kg lecithin supplemented treatments. These data indicate that dietary lecithin supplementation has the potential to improve the quality attributes of pork from female pigs. PMID:26610579

A Tiered Analytical Approach for Investigating Poor Quality Emergency Contraceptives

PubMed Central

Monge, María Eugenia; Dwivedi, Prabha; Zhou, Manshui; Payne, Michael; Harris, Chris; House, Blaine; Juggins, Yvonne; Cizmarik, Peter; Newton, Paul N.; Fernández, Facundo M.; Jenkins, David

2014-01-01

Reproductive health has been deleteriously affected by poor quality medicines. Emergency contraceptive pills (ECPs) are an important birth control method that women can use after unprotected coitus for reducing the risk of pregnancy. In response to the detection of poor quality ECPs commercially available in the Peruvian market we developed a tiered multi-platform analytical strategy. In a survey to assess ECP medicine quality in Peru, 7 out of 25 different batches showed inadequate release of levonorgestrel by dissolution testing or improper amounts of active ingredient. One batch was found to contain a wrong active ingredient, with no detectable levonorgestrel. By combining ultrahigh performance liquid chromatography-ion mobility spectrometry-mass spectrometry (UHPLC-IMS-MS) and direct analysis in real time MS (DART-MS) the unknown compound was identified as the antibiotic sulfamethoxazole. Quantitation by UHPLC-triple quadrupole tandem MS (QqQ-MS/MS) indicated that the wrong ingredient was present in the ECP sample at levels which could have significant physiological effects. Further chemical characterization of the poor quality ECP samples included the identification of the excipients by 2D Diffusion-Ordered Nuclear Magnetic Resonance Spectroscopy (DOSY 1H NMR) indicating the presence of lactose and magnesium stearate. PMID:24748219

Impact of a packing medium with alga Bifurcaria bifurcata extract on canned Atlantic mackerel (Scomber scombrus) quality.

PubMed

Barbosa, Roberta G; Trigo, Marcos; Fett, Roseane; Aubourg, Santiago P

2018-01-03

The present research focused on the quality of canned fish. Its primary objective was the quality enhancement of canned Atlantic mackerel (Scomber scombrus) by including an aqueous Bifurcaria bifurcata extract in the packing medium. Various alga extract concentrations were tested and compared with a control without alga extract. After 3 months of canned storage, the cans were opened and quality changes in fish white muscle were analyzed. An inhibitory effect on lipid oxidation development (tertiary compound formation) and color parameter (L* and b*) values was observed as a result of the alga presence in the packing medium. On the contrary, the presence of the alga extract did not produce any effect on volatile compound (total and trimethylamine) formation and lipid hydrolysis (free fatty acid formation) development. A preservative effect derived from the use of an aqueous B. bifurcata extract as packing medium is concluded, and this result is primarily linked to the presence of hydrophilic preservative molecules. The packing system proposed in this work constitutes a novel and promising strategy to enhance the quality of commercial canned fish products. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Refocusing Mussel Watch on contaminants of emerging concern (CECs): the California pilot study (2009-10)

USGS Publications Warehouse

Maruya, Keith A.; Dodder, Nathan G.; Schaffner, Rebecca A.; Weisberg, Stephen B.; Gregorio, Dominic; Klosterhaus, Susan; Alvarez, David A.; Furlong, Edward T.; Kimbrough, Kimani L.; Lauenstein, Gunnar G.; Christensen, John D.

2014-01-01

To expand the utility of the Mussel Watch Program, local, regional and state agencies in California partnered with NOAA to design a pilot study that targeted contaminants of emerging concern (CECs). Native mussels (Mytilus spp.) from 68 stations, stratified by land use and discharge scenario, were collected in 2009–10 and analyzed for 167 individual pharmaceuticals, industrial and commercial chemicals and current use pesticides. Passive sampling devices (PSDs) and caged Mytilus were co-deployed to expand the list of CECs, and to assess the ability of PSDs to mimic bioaccumulation by Mytilus. A performance-based quality assurance/quality control (QA/QC) approach was developed to ensure a high degree of data quality, consistency and comparability. Data management and analysis were streamlined and standardized using automated software tools. This pioneering study will help shape future monitoring efforts in California’s coastal ecosystems, while serving as a model for monitoring CECs within the region and across the nation.

Energy and water quality management systems for water utility's operations: a review.

PubMed

Cherchi, Carla; Badruzzaman, Mohammad; Oppenheimer, Joan; Bros, Christopher M; Jacangelo, Joseph G

2015-04-15

Holistic management of water and energy resources is critical for water utilities facing increasing energy prices, water supply shortage and stringent regulatory requirements. In the early 1990s, the concept of an integrated Energy and Water Quality Management System (EWQMS) was developed as an operational optimization framework for solving water quality, water supply and energy management problems simultaneously. Approximately twenty water utilities have implemented an EWQMS by interfacing commercial or in-house software optimization programs with existing control systems. For utilities with an installed EWQMS, operating cost savings of 8-15% have been reported due to higher use of cheaper tariff periods and better operating efficiencies, resulting in the reduction in energy consumption of ∼6-9%. This review provides the current state-of-knowledge on EWQMS typical structural features and operational strategies and benefits and drawbacks are analyzed. The review also highlights the challenges encountered during installation and implementation of EWQMS and identifies the knowledge gaps that should motivate new research efforts. Copyright © 2015 Elsevier Ltd. All rights reserved.

Growth and quality of soybean sprouts (Glycine max L. Merrill) as affected by gamma irradiation

NASA Astrophysics Data System (ADS)

Yun, Juan; Li, Xihong; Fan, Xuetong; Li, Weili; Jiang, Yuqian

2013-01-01

In this study, soybean seeds and sprouts (Glycine max L. Merrill) were exposed to radiation doses up to 3.0 kGy. The irradiated and non-irradiated seeds were germinated, and then germination rate, sprouts length, vitamin C content, antioxidants and visual and olfactory quality were determined after irradiation. Results indicated that there was no significant difference in the germination rate and sprouts length between the control and 0.3 kGy treated soybeans, however, the reductions in sprouts length of the 1.0 kGy and 3.0 kGy treated samples were quite significant with reductions of 20.4% and 58.8%, respectively. Irradiated sprouts had similar visual and olfactory quality as the non-irradiated one. Therefore, irradiation of seeds alone would have limited value in terms of commercial use due to reduced germination and length of sprouts. However, irradiation of sprouts at doses up to 3.0 kGy was feasible to enhance microbial safety of sprouts.

Spatial Allocator for air quality modeling

EPA Pesticide Factsheets

The Spatial Allocator is a set of tools that helps users manipulate and generate data files related to emissions and air quality modeling without requiring the use of a commercial Geographic Information System.

Phenotyping the quality of complex medium components by simple online-monitored shake flask experiments.

PubMed

Diederichs, Sylvia; Korona, Anna; Staaden, Antje; Kroutil, Wolfgang; Honda, Kohsuke; Ohtake, Hisao; Büchs, Jochen

2014-11-07

Media containing yeast extracts and other complex raw materials are widely used for the cultivation of microorganisms. However, variations in the specific nutrient composition can occur, due to differences in the complex raw material ingredients and in the production of these components. These lot-to-lot variations can affect growth rate, product yield and product quality in laboratory investigations and biopharmaceutical production processes. In the FDA's Process Analytical Technology (PAT) initiative, the control and assessment of the quality of critical raw materials is one key aspect to maintain product quality and consistency. In this study, the Respiration Activity Monitoring System (RAMOS) was used to evaluate the impact of different yeast extracts and commercial complex auto-induction medium lots on metabolic activity and product yield of four recombinant Escherichia coli variants encoding different enzymes. Under non-induced conditions, the oxygen transfer rate (OTR) of E. coli was not affected by a variation of the supplemented yeast extract lot. The comparison of E. coli cultivations under induced conditions exhibited tremendous differences in OTR profiles and volumetric activity for all investigated yeast extract lots of different suppliers as well as lots of the same supplier independent of the E. coli variant. Cultivation in the commercial auto-induction medium lots revealed the same reproducible variations. In cultivations with parallel offline analysis, the highest volumetric activity was found at different cultivation times. Only by online monitoring of the cultures, a distinct cultivation phase (e.g. glycerol depletion) could be detected and chosen for comparable and reproducible offline analysis of the yield of functional product. This work proves that cultivations conducted in complex media may be prone to significant variation in final product quality and quantity if the quality of the raw material for medium preparation is not thoroughly checked. In this study, the RAMOS technique enabled a reliable and reproducible screening and phenotyping of complex raw material lots by online measurement of the respiration activity. Consequently, complex raw material lots can efficiently be assessed if the distinct effects on culture behavior and final product quality and quantity are visualized.

Is Low-field NMR a Complementary Tool to GC-MS in Quality Control of Essential Oils? A Case Study: Patchouli Essential Oil.

PubMed

Krause, Andre; Wu, Yu; Tian, Runtao; van Beek, Teris A

2018-04-24

High-field NMR is an expensive and important quality control technique. In recent years, cheaper and simpler low-field NMR has become available as a new quality control technique. In this study, 60 MHz 1 H-NMR was compared with GC-MS and refractometry for the detection of adulteration of essential oils, taking patchouli essential oil as a test case. Patchouli essential oil is frequently adulterated, even today. In total, 75 genuine patchouli essential oils, 10 commercial patchouli essential oils, 10 other essential oils, 17 adulterants, and 1 patchouli essential oil, spiked at 20% with those adulterants, were measured. Visual inspection of the NMR spectra allowed for easy detection of 14 adulterants, while gurjun and copaiba balsams proved difficult and one adulterant could not be detected. NMR spectra of 10 random essential oils differed not only strongly from patchouli essential oil but also from one another, suggesting that fingerprinting by low-field NMR is not limited to patchouli essential oil. Automated chemometric evaluation of NMR spectra was possible by similarity analysis (Mahalanobis distance) based on the integration from 0.1 - 8.1 ppm in 0.01 ppm increments. Good quality patchouli essential oils were recognised as well as 15 of 17 deliberate adulterations. Visual qualitative inspection by GC-MS allowed for the detection of all volatile adulterants. Nonvolatile adulterants, and all but one volatile adulterant, could be detected by semiquantitation. Different chemometric approaches showed satisfactory results. Similarity analyses were difficult with nonvolatile adulterants. Refractive index measurements could detect only 8 of 17 adulterants. Due to advantages such as simplicity, rapidity, reproducibility, and ability to detect nonvolatile adulterants, 60 MHz 1 H-NMR is complimentary to GC-MS for quality control of essential oils. Georg Thieme Verlag KG Stuttgart · New York.

Health and perception of cabin air quality among Swedish commercial airline crew.

PubMed

Lindgren, T; Norbäck, D

2005-01-01

Health symptoms and perception of cabin air quality (CAQ) among commercial cabin crew were studied as a function of personal risk factors, occupation, and work on intercontinental flights with exposure to environmental tobacco smoke (ETS). A standardized questionnaire (MM 040 NA) was mailed in February to March 1997 to all Stockholm airline crew on duty in a Scandinavian airline (n=1857), and to office workers from the same airline (n=218). During this time, smoking was allowed only on intercontinental flights. The participation rate was 81% (n=1513) by the airline crew, and 77% (n=168) by the office group. Statistical analysis was performed by multiple logistic regression analysis, controlling for age, gender, atopy, current smoking habits, and occupation. The most common symptoms among airline crew were: fatigue (21%), nasal symptoms (15%), eye irritation (11%), dry or flushed facial skin (12%), and dry/itchy skin on hands (12%). The most common complaint about CAQ was dry air (53%). Airline crew had more nasal, throat, and hand skin symptoms, than office workers did. Airline crew with a history of atopy had more nasal, throat, and dermal face and hand symptoms than other crew members did. Older airline crew members had more complaints of difficulty concentrating, but fewer complaints of dermal symptoms on the face and hands than younger crew members did. Female crew members reported more headaches than male crew members reported. Smoking was not associated with frequency of symptoms. Pilots had fewer complaints of most symptoms than other crew had. Airline crew that had been on an intercontinental flight in the week before the survey had more complaints of fatigue, heavy-headedness, and difficulty concentrating. Complaints of stuffy air and dry air were more common among airline crew than among office workers from the same airline. Female crew had more complaints of stuffy and dry air than male crew had. Older cabin crew had fewer complaints of dry air than younger crew had, and cabin crew with atopy had more complaints of dry air than other crew had. Current smokers had fewer complaints of stuffy air than non-smokers had. Airline crew that had been on a flight on which smoking was allowed in the week before the survey, had more complaints of stuffy air, dry air and passive smoking, than crew that had not been on such a flight in the preceding week had. Complaints on cabin air quality and health symptoms were common among commercial airline crew, and related to age, gender, atopy and type of work onboard. The hygienic measurements showed that the relative air humidity is very low on intercontinental flights, and particle levels are high on flights with passive smoking. This illustrates the need to improve the cabin air quality in commercial airlines. Such improvements could include better control of cabin temperature, air humidification, efficient air filtration with high efficiency particulate air filter (HEPA) filtration on all types of aircraft and sufficient air exchange rate in order to fulfil current ventilation standards.

A Two-Year Water Quality Monitoring Curriculum.

ERIC Educational Resources Information Center

Glazer, Richard B.; And Others

The Environmental Protection Agency developed this curriculum to train technicians to monitor water quality. Graduates of the program should be able to monitor municipal, industrial, and commercial discharges; test drinking water for purity; and determine quality of aquatic environments. The program includes algebra, communication skills, biology,…

THz identification and Bayes modeling

NASA Astrophysics Data System (ADS)

Sokolnikov, Andre

2017-05-01

THz Identification is a developing technology. Sensing in the THz range potentially gives opportunity for short range radar sensing because THz waves can better penetrate through obscured atmosphere, such as fog, than visible light. The lower scattering of THz as opposed to the visible light results also in significantly better imaging than in IR spectrum. A much higher contrast can be achieved in medical trans-illumination applications than with X-rays or visible light. The same THz radiation qualities produce better tomographical images from hard surfaces, e.g. ceramics. This effect comes from the delay in time of reflected THz pulses detection. For special or commercial applications alike, the industrial quality control of defects is facilitated with a lower cost. The effectiveness of THz wave measurements is increased with computational methods. One of them is Bayes modeling. Examples of this kind of mathematical modeling are considered.

Crystal growth of device quality GaAs in space

NASA Technical Reports Server (NTRS)

Gatos, H. C.; Lagowski, J.

1983-01-01

GaAs device technology has recently reached a new phase of rapid advancement, made possible by the improvement of the quality of GaAs bulk crystals. At the same time, the transition to the next generation of GaAs integrated circuits and optoelectronic systems for commercial and government applications hinges on new quantum steps in three interrelated areas: crystal growth, device processing and device-related properties and phenomena. Special emphasis is placed on the establishment of quantitative relationships among crystal growth parameters-material properties-electronic properties and device applications. The overall program combines studies of crystal growth on novel approaches to engineering of semiconductor material (i.e., GaAs and related compounds); investigation and correlation of materials properties and electronic characteristics on a macro- and microscale; and investigation of electronic properties and phenomena controlling device applications and device performance.

32 CFR 861.1 - References.

Code of Federal Regulations, 2010 CFR

2010-07-01

...: (a) 10 U.S.C. 2640, Charter Air Transportation of Members of the Armed Forces. (b) Department of Defense Directive 4500.53, Department of Defense Commercial Air Transportation Quality and Safety Review... Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT DEPARTMENT OF DEFENSE COMMERCIAL AIR...

Use of Commercial FPGA-Based Evaluation Boards for Single-Event Testing of DDR2 and DDR3 SDRAMs

NASA Technical Reports Server (NTRS)

Ladbury, R. L.; Berg, M. D.; Wilcox, E. P.; LaBel, K. A.; Kim, H. S.; Phan, A. M.; Seidleck, C. M.

2013-01-01

We investigate the use of commercial FPGA based evaluation boards for radiation testing DDR2 and DDR3 SDRAMs. We evaluate the resulting data quality and the tradeoffs involved in the use of these boards.

Temperature and Humidity Calibration of a Low-Cost Wireless Dust Sensor for Real-Time Monitoring.

PubMed

Hojaiji, Hannaneh; Kalantarian, Haik; Bui, Alex A T; King, Christine E; Sarrafzadeh, Majid

2017-03-01

This paper introduces the design, calibration, and validation of a low-cost portable sensor for the real-time measurement of dust particles within the environment. The proposed design consists of low hardware cost and calibration based on temperature and humidity sensing to achieve accurate processing of airborne dust density. Using commercial particulate matter sensors, a highly accurate air quality monitoring sensor was designed and calibrated using real world variations in humidity and temperature for indoor and outdoor applications. Furthermore, to provide a low-cost secure solution for real-time data transfer and monitoring, an onboard Bluetooth module with AES data encryption protocol was implemented. The wireless sensor was tested against a Dylos DC1100 Pro Air Quality Monitor, as well as an Alphasense OPC-N2 optical air quality monitoring sensor for accuracy. The sensor was also tested for reliability by comparing the sensor to an exact copy of itself under indoor and outdoor conditions. It was found that accurate measurements under real-world humid and temperature varying and dynamically changing conditions were achievable using the proposed sensor when compared to the commercially available sensors. In addition to accurate and reliable sensing, this sensor was designed to be wearable and perform real-time data collection and transmission, making it easy to collect and analyze data for air quality monitoring and real-time feedback in remote health monitoring applications. Thus, the proposed device achieves high quality measurements at lower-cost solutions than commercially available wireless sensors for air quality.

Combined Expression of Aspergillus nidulans Endoxylanase X24 and Aspergillus oryzae (alpha)-Amylase in Industrial Baker's Yeasts and Their Use in Bread Making.

PubMed

Monfort, A; Blasco, A; Prieto, J A; Sanz, P

1996-10-01

The Aspergillus nidulans endoxylanase X24 and the Aspergillus oryzae (alpha)-amylase cDNAs were placed under the control of the Saccharomyces cerevisiae actin promoter (pACT1) and introduced into baker's yeast. Bread made with transformants expressing both enzymes (YEpACT-AMY-ACT-X24) showed a 30% increase in volume and reduced firmness in comparison with that produced with a commercial strain. Endoxylanase X24 and (alpha)-amylase seem to act synergistically to improve the quality of bread in terms of volume and density.

Combined Expression of Aspergillus nidulans Endoxylanase X24 and Aspergillus oryzae (alpha)-Amylase in Industrial Baker's Yeasts and Their Use in Bread Making

PubMed Central

Monfort, A.; Blasco, A.; Prieto, J. A.; Sanz, P.

1996-01-01

The Aspergillus nidulans endoxylanase X24 and the Aspergillus oryzae (alpha)-amylase cDNAs were placed under the control of the Saccharomyces cerevisiae actin promoter (pACT1) and introduced into baker's yeast. Bread made with transformants expressing both enzymes (YEpACT-AMY-ACT-X24) showed a 30% increase in volume and reduced firmness in comparison with that produced with a commercial strain. Endoxylanase X24 and (alpha)-amylase seem to act synergistically to improve the quality of bread in terms of volume and density. PMID:16535419

Improved Advanced Actuated Hybrid Mirrors Final Report CRADA No. TC02130.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbee, T. W.; Ealey, M. A.

2017-08-25

This was a collaborative effort to develop and demonstrate an improved Advanced Actuated Hybrid Mirrors (AAHM) for commercial or Government purposes. The AAHM consists of a nanolaminate film replicating a precision optical surface bonded to a Silicon Carbide (SiC) substrate with active figure control capability. The goal of this project was to further the development of specific AAHM technologies. The intent of the CRADA was to combine the expertise of LLNL and NG Xinetics in the manufacture and test of a very high quality AAHM, incorporating lessons learned from earlier joint efforts.

Making change easy: A peer-to-peer guide on transitioning to new hand hygiene products.

PubMed

Amirov, Chingiz M; Candon, Heather L; Jacob, Latha

2017-01-01

This report summarizes our experiences planning and implementing the transition to a new commercial line of hand hygiene products and their dispensing systems in a large academic health care facility in Toronto, Canada. Our lessons learned are organized into a practical guide made available in 2 different formats: this article and an illustrated peer-to-peer guide (http://www.baycrest.org/wp-content/uploads/HCE-PROG-HH_HighQuality.pdf). Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Numerical simulation of temperature and pressure fields in CdTe growth experiment in the Material Science Laboratory (MSL) onboard the International Space Station in relation to dewetting

NASA Astrophysics Data System (ADS)

Sylla, Lamine; Duffar, Thierry

2007-05-01

A global thermal modelling of a cadmium telluride (CdTe) space experiment has been performed to determine the temperature field within the sample cartridge assembly of the Material Science Laboratory-low gradient furnace (MSL-LGF) apparatus. Heat transfer and phase change have been treated with a commercial CFD software based on a control volume technique. This work underlines the difficult compromise between enhancing the crystal quality and the occurrence of the dewetting phenomenon when using a Cd overpressure or inert gas in the ampoule.

Stereoscopic display technologies for FHD 3D LCD TV

NASA Astrophysics Data System (ADS)

Kim, Dae-Sik; Ko, Young-Ji; Park, Sang-Moo; Jung, Jong-Hoon; Shestak, Sergey

2010-04-01

Stereoscopic display technologies have been developed as one of advanced displays, and many TV industrials have been trying commercialization of 3D TV. We have been developing 3D TV based on LCD with LED BLU (backlight unit) since Samsung launched the world's first 3D TV based on PDP. However, the data scanning of panel and LC's response characteristics of LCD TV cause interference among frames (that is crosstalk), and this makes 3D video quality worse. We propose the method to reduce crosstalk by LCD driving and backlight control of FHD 3D LCD TV.

Environmental Assessment of the City of El Cerrito, CA: Creek, Trash and Air Quality Analysis

NASA Astrophysics Data System (ADS)

Moore, A.; Ilan, A.

2015-12-01

The City of El Cerrito, CA is located within Western Contra Costa County and adjacent to the San Francisco Bay. Local land-uses that affect its overall public and environmental health include major freeways, railways, and commercial and industrial zones. In an effort to assess the overall health of the local environment, students at Korematsu Middle School conducted a comprehensive analysis that included street litter auditing, water monitoring of Cerritos Creek and air quality measurements made along local streets. In 2014 the City of El Cerrito adopted a long-term trash plan that included strategies for reducing trash loads of local stormwater sewer systems. This plan called for load reduction of 70% by July 1, 2017 and 100% by July 1, 2022. To evaluate the effectiveness of the trash plan, our team quantified and scored trash concentration levels at two locations—one in a residential neighborhood and the other in a commercial zone. We also monitored water quality at nearby Cerritos Creek to investigate the impacts that each area's trash concentrations had on water quality. We also monitored particulate matter (PM) concentration levels in air within these locations to determine whether or not differences exist between residential and commercial areas. Preliminary analysis of litter data suggests that the Long Term Trash Plan has thus far been effective in reducing concentrations of street litter along San Pablo Avenue, which is located within a major commercial zone, but has been inadequate in reducing trash in nearby parks. Water quality results indicate that Cerritos Creek contains waters that are quite healthy with respect to Ammonia and Nitrate concentration levels (i.e., very low values for every sample collected). However, elevated concentration levels of Phosphates were detected in every sample collected. Air quality data surprisingly revealed that extremely high PM concentration levels occur in air surrounding a residential park in El Cerrito.

Multileaf collimator performance monitoring and improvement using semiautomated quality control testing and statistical process control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Létourneau, Daniel, E-mail: daniel.letourneau@rmp.uh.on.ca; McNiven, Andrea; Keller, Harald

2014-12-15

Purpose: High-quality radiation therapy using highly conformal dose distributions and image-guided techniques requires optimum machine delivery performance. In this work, a monitoring system for multileaf collimator (MLC) performance, integrating semiautomated MLC quality control (QC) tests and statistical process control tools, was developed. The MLC performance monitoring system was used for almost a year on two commercially available MLC models. Control charts were used to establish MLC performance and assess test frequency required to achieve a given level of performance. MLC-related interlocks and servicing events were recorded during the monitoring period and were investigated as indicators of MLC performance variations. Methods:more » The QC test developed as part of the MLC performance monitoring system uses 2D megavoltage images (acquired using an electronic portal imaging device) of 23 fields to determine the location of the leaves with respect to the radiation isocenter. The precision of the MLC performance monitoring QC test and the MLC itself was assessed by detecting the MLC leaf positions on 127 megavoltage images of a static field. After initial calibration, the MLC performance monitoring QC test was performed 3–4 times/week over a period of 10–11 months to monitor positional accuracy of individual leaves for two different MLC models. Analysis of test results was performed using individuals control charts per leaf with control limits computed based on the measurements as well as two sets of specifications of ±0.5 and ±1 mm. Out-of-specification and out-of-control leaves were automatically flagged by the monitoring system and reviewed monthly by physicists. MLC-related interlocks reported by the linear accelerator and servicing events were recorded to help identify potential causes of nonrandom MLC leaf positioning variations. Results: The precision of the MLC performance monitoring QC test and the MLC itself was within ±0.22 mm for most MLC leaves and the majority of the apparent leaf motion was attributed to beam spot displacements between irradiations. The MLC QC test was performed 193 and 162 times over the monitoring period for the studied units and recalibration had to be repeated up to three times on one of these units. For both units, rate of MLC interlocks was moderately associated with MLC servicing events. The strongest association with the MLC performance was observed between the MLC servicing events and the total number of out-of-control leaves. The average elapsed time for which the number of out-of-specification or out-of-control leaves was within a given performance threshold was computed and used to assess adequacy of MLC test frequency. Conclusions: A MLC performance monitoring system has been developed and implemented to acquire high-quality QC data at high frequency. This is enabled by the relatively short acquisition time for the images and automatic image analysis. The monitoring system was also used to record and track the rate of MLC-related interlocks and servicing events. MLC performances for two commercially available MLC models have been assessed and the results support monthly test frequency for widely accepted ±1 mm specifications. Higher QC test frequency is however required to maintain tighter specification and in-control behavior.« less

Commercial gaming devices for stroke upper limb rehabilitation: a systematic review.

PubMed

Thomson, Katie; Pollock, Alex; Bugge, Carol; Brady, Marian

2014-06-01

Rehabilitation using commercial gaming devices is a new concept for stroke care. Commercial gaming devices such as Nintendo Wii or Sony PlayStation encourage high repetition of arm movements and are being introduced into some clinical settings. The evidence base for gaming use in rehabilitation is growing rapidly and there is a need to systematically synthesise research. Our review aims to integrate evidence on how gaming is being used, explore patient/therapist experience and synthesise evidence of effectiveness. An integrative systematic review was undertaken searching Cochrane Central Register of Controlled Trials (2013), Medline (2013), Embase (2013) and twelve additional databases. Two review authors independently selected studies based on pre-defined inclusion criteria, extracted data and assessed risk of bias. Nineteen studies including 215 patients met inclusion criteria. Studies were typically small scale feasibility studies using a range of research designs, limiting the ability to reach generalised conclusions. Results have been tabulated (activities of daily living, upper limb function/ movement) and qualitative themes identified. Findings suggest that most patients enjoy using commercial gaming and can tolerate 180 mins per week without significant adverse effects. A trend towards improvement was noted for upper limb function/ movement. Few studies recorded outcomes related to activities of daily living or focused on understanding patients' experiences of this intervention. Commercial gaming can provide high intensity upper limb practice however there is insufficient high quality evidence to reach generalisable conclusions about risks or benefits on activities of daily living or upper limb function/movement. © 2014 The Authors. International Journal of Stroke © 2014 World Stroke Organization.

Dietary management of childhood diarrhea in low- and middle-income countries: a systematic review

PubMed Central

2013-01-01

Background Current WHO guidelines on the management and treatment of diarrhea in children strongly recommend continued feeding alongside the administration of oral rehydration solution and zinc therapy, but there remains some debate regarding the optimal diet or dietary ingredients for feeding children with diarrhea. Methods We conducted a systematic search for all published randomized controlled trials evaluating food-based interventions among children under five years old with diarrhea in low- and middle-income countries. We classified 29 eligible studies into one or more comparisons: reduced versus regular lactose liquid feeds, lactose-free versus lactose-containing liquid feeds, lactose-free liquid feeds versus lactose-containing mixed diets, and commercial/specialized ingredients versus home-available ingredients. We used all available outcome data to conduct random-effects meta-analyses to estimate the average effect of each intervention on diarrhea duration, stool output, weight gain and treatment failure risk for studies on acute and persistent diarrhea separately. Results Evidence of low-to-moderate quality suggests that among children with acute diarrhea, diluting or fermenting lactose-containing liquid feeds does not affect any outcome when compared with an ordinary lactose-containing liquid feeds. In contrast, moderate quality evidence suggests that lactose-free liquid feeds reduce duration and the risk of treatment failure compared to lactose-containing liquid feeds in acute diarrhea. Only limited evidence of low quality was available to assess either of these two approaches in persistent diarrhea, or to assess lactose-free liquid feeds compared to lactose-containing mixed diets in either acute or persistent diarrhea. For commercially prepared or specialized ingredients compared to home-available ingredients, we found low-to-moderate quality evidence of no effect on any outcome in either acute or persistent diarrhea, though when we restricted these analyses to studies where both intervention and control diets were lactose-free, weight gain in children with acute diarrhea was shown to be greater among those fed with a home-available diet. Conclusions Among children in low- and middle-income countries, where the dual burden of diarrhea and malnutrition is greatest and where access to proprietary formulas and specialized ingredients is limited, the use of locally available age-appropriate foods should be promoted for the majority of acute diarrhea cases. Lactose intolerance is an important complication in some cases, but even among those children for whom lactose avoidance may be necessary, nutritionally complete diets comprised of locally available ingredients can be used at least as effectively as commercial preparations or specialized ingredients. These same conclusions may also apply to the dietary management of children with persistent diarrhea, but the evidence remains limited. PMID:24564685

Monitoring the quality consistency of Fufang Danshen Pills using micellar electrokinetic chromatography fingerprint coupled with prediction of antioxidant activity and chemometrics.

PubMed

Ji, Zhengchao; Sun, Wanyang; Sun, Guoxiang; Zhang, Jin

2016-08-01

A fast micellar electrokinetic chromatography fingerprint method combined with quantification was developed and validated to evaluate the quality of Fufang Danshen Pills, a traditional Chinese Medicine, which has been used in the treatment of cardiovascular system diseases, in which the tetrahedron optimization method was first used to optimize the background electrolyte solution. Subsequently, the index of the fingerprint information amount of I was performed as an excellent objective indictor to investigate the experimental conditions. In addition, a systematical quantified fingerprint method was constructed for evaluating the quality consistency of 20 batches of test samples obtained from the same drug manufacturer. The fingerprint analysis combined with quantitative determination of two components showed that the quality consistency of the test samples was quite good within the same commercial brand. Furthermore, the partial least squares model analysis was used to explore the fingerprint-efficacy relationship between active components and antioxidant activity in vitro, which can be applied for the assessment of anti-oxidant activity of Fufang Danshen pills and provide valuable medicinal information for quality control. The result illustrated that the present study provided a reliable and reasonable method for monitoring the quality consistency of Fufang Danshen pills. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Type 2 diabetes detection and management among insured adults.

PubMed

Dall, Timothy M; Yang, Weyna; Halder, Pragna; Franz, Jerry; Byrne, Erin; Semilla, April P; Chakrabarti, Ritashree; Stuart, Bruce

2016-01-01

The Centers for Disease Control and Prevention estimates that 28.9 million adults had diabetes in 2012 in the US, though many patients are undiagnosed or not managing their condition. This study provides US national and state estimates of insured adults with type 2 diabetes who are diagnosed, receiving exams and medication, managing glycemic levels, with diabetes complications, and their health expenditures. Such information can be used for benchmarking and to identify gaps in diabetes detection and management. The study combines analysis of survey data with medical claims analysis for the commercially insured, Medicare, and Medicaid populations to estimate the number of adults with diagnosed type 2 diabetes and undiagnosed diabetes by insurance type, age, and sex. Medical claims analysis used the 2012 de-identified Normative Health Information database covering a nationally representative commercially insured population, the 2011 Medicare 5% Sample, and the 2008 Medicaid Mini-Max. Among insured adults in 2012, approximately 16.9 million had diagnosed type 2 diabetes, 1.45 million had diagnosed type 1 diabetes, and 6.9 million had undiagnosed diabetes. Of those with diagnosed type 2, approximately 13.0 million (77%) received diabetes medication-ranging from 70% in New Jersey to 82% in Utah. Suboptimal percentages had claims indicating recommended exams were performed. Of those receiving diabetes medication, 43% (5.6 million) had medical claims indicating poorly controlled diabetes-ranging from 29% with poor control in Minnesota and Iowa to 53% in Texas. Poor control was correlated with higher prevalence of neurological complications (+14%), renal complications (+14%), and peripheral vascular disease (+11%). Patients with poor control averaged $4,860 higher average annual health care expenditures-ranging from $6,680 for commercially insured patients to $4,360 for Medicaid and $3,430 for Medicare patients. This study highlights the large number of insured adults with undiagnosed type 2 diabetes by insurance type and state. Furthermore, this study sheds light on other gaps in diabetes care quality among patients with diagnosed diabetes and corresponding poorly controlled diabetes. These findings underscore the need for improvements in data collection and diabetes screening and management, along with policies that support these improvements.

The FAA's Approach to Quality Assurance in the Flight Safety Analysis of Launch and Reentry Vehicles

NASA Astrophysics Data System (ADS)

Murray, Daniel P.; Weil, Andre

2010-09-01

The U.S. Federal Aviation Administration(FAA) Office of Commercial Space Transportation’s safety mission is to ensure protection of the public, property, and the national security and foreign policy interests of the United States during commercial launch and reentry activities. As part of this mission, the FAA issues licenses to the operators of launch and reentry vehicles who successfully demonstrate compliance with FAA regulations. To meet these regulations, vehicle operators submit an application that contains, among other things, flight safety analyses of their proposed missions. In the process of evaluating these submitted analyses, the FAA often conducts its own independent analyses, using input data from the submitted license application. These analyses are conducted according to approved procedures using industry developed tools. To assist in achieving the highest levels of quality in these independent analyses, the FAA has developed a quality assurance program that consists of multiple levels of review. These reviews rely on the work of multiple teams, as well as additional, independently performed work of support contractors. This paper describes the FAA’s quality assurance process for flight safety analyses. Members of the commercial space industry may find that elements of this process can be easily applied to their own analyses, improving the quality of the material they submit to the FAA in their license applications.

Variation of meat quality traits among five genotypes of chicken.

PubMed

Tang, H; Gong, Y Z; Wu, C X; Jiang, J; Wang, Y; Li, K

2009-10-01

The main objective of this study was to examine the diversity of meat quality traits among 5 chicken genotypes. The genotypes included 2 Chinese native breeds (Wenchang,WCH, and Xianju), 1 commercial broiler line (Avian, AV), 1 commercial layer line (Hy-Line Brown, HLB), and 1 Chinese commercial broiler line (Lingnanhuang, LNH) synthesized by exotic and native breeds, which were slaughtered at their market ages: 16, 7, 16, and 8 wk, respectively. The effects of genotype, muscle type, and sex on meat quality traits were examined. Birds from slow-growing genotypes (WCH, Xianju, and HLB) exhibited higher shear value, inosine-5'-monophosphate concentration, lower cook loss, and more fat than those from fast-growing genotypes (AV and LNH). Chickens from WCH possessed the lowest expressible moisture, cook loss, and the highest lipid (%) among the 3 slow-growing genotypes. The HLB birds were intermediate in expressible moisture and cook loss and lowest in lipid among all genotypes. The LNH cross birds were similar to AV broilers in most meat quality parameters, although they had a lower shear force value and higher fat content than AV broilers. Breast muscle had higher expressible moisture, shear force, protein (%), inosine-5'-monophosphate content, lower cook loss, and lipid (%) than leg muscle. Muscles from male chickens had higher expressible moisture than those from the females. Variability of meat quality characteristics is mainly related to genotype and muscle type differences.

7 CFR 58.142 - Product quality and stability.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Procedures § 58.142 Product quality and stability. The receiving, holding and processing of milk and cream... accordance with clean and sanitary methods, consistent with good commercial practices to promote the production of the highest quality of finished product and improve product stability. Milk should not be more...

7 CFR 58.142 - Product quality and stability.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Procedures § 58.142 Product quality and stability. The receiving, holding and processing of milk and cream... accordance with clean and sanitary methods, consistent with good commercial practices to promote the production of the highest quality of finished product and improve product stability. Milk should not be more...

7 CFR 58.142 - Product quality and stability.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Procedures § 58.142 Product quality and stability. The receiving, holding and processing of milk and cream... accordance with clean and sanitary methods, consistent with good commercial practices to promote the production of the highest quality of finished product and improve product stability. Milk should not be more...

7 CFR 58.142 - Product quality and stability.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Procedures § 58.142 Product quality and stability. The receiving, holding and processing of milk and cream... accordance with clean and sanitary methods, consistent with good commercial practices to promote the production of the highest quality of finished product and improve product stability. Milk should not be more...

Visual Grading and Quality of 1-0 Northern Red Oak Seedlings

Treesearch

S.L. Clark; S.E. Scblarbaum; Paul P. Kormanik

2000-01-01

Past research has used detailed measurements of various growth characteristics to determine seedling grades and quality of northern red oak nursery stock This study evaluates the effectiveness ofa visual grading process. similar to thosefound in commercial nursery operations, to distinguish high quality seedlings. Northern red oak (Quercus rubra...

Evaluation of the nutritional equivalency of soybean meal with the genetically modified trait DP-3O5423-1 when fed to laying hens.

PubMed

Mejia, L; Jacobs, C M; Utterback, P L; Parsons, C M; Rice, D; Sanders, C; Smith, B; Iiams, C; Sauber, T

2010-12-01

An experiment using 336 Hy-Line W-36 Single Comb White Leghorn hens was conducted to evaluate transgenic soybeans containing the gm-fad2-1 gene fragment and the gm-hra gene. Transcription of the gm-fad2-1 gene fragment results in an increased level of oleic acid (18:1) in the seed, and expression of the soybean acetolactate synthase protein (GM-HRA) encoded by the modified gm-hra gene, is used as a selectable marker during transformation. Pullets (20 wk of age) were placed in cage lots (7 hens/cage, 2 cages/lot) and were randomly assigned to 1 of 4 corn-soybean meal dietary treatments (6 lots/treatment) formulated with the following soybean meals: nontransgenic near-isoline control (control), nontransgenic commercial reference soybean meal A (92M72), nontransgenic commercial reference soybean meal B (93B15), or transgenic soybean meal produced from soybeans containing event DP-3Ø5423-1 (305423). Weeks 20 to 24 were a preconditioning period, and the 4 experimental diets were then fed from 25 to 36 wk of age. Differences between the 305423 and control group means were evaluated, with statistical significance at P < 0.05. Body weight, hen-day egg production, egg mass, feed consumption, and feed efficiency for hens fed the 305423 soybean meal were not significantly different from the respective values for hens fed diets formulated with the near-isoline soybean meal. Likewise, egg component weights, Haugh unit measures, and egg weights were similar regardless of the soybean meal source. This research indicates that performance of hens fed diets containing 305423 soybean meal, as measured by egg production and egg quality, was similar to that of hens fed diets formulated with the near-isoline control and commercial soybean meals.