LG based decision aid for naval tactical action officer's (TAO) workstation

NASA Astrophysics Data System (ADS)

Stilman, Boris; Yakhnis, Vladimir; Umanskiy, Oleg; Boyd, Ron

2005-05-01

In the increasingly NetCentric battlespace of the 21st century, Stilman Advanced Strategies Linguistic Geometry software has the potential to revolutionize the way that the Navy fights in two key areas: as a Tactical Decision Aid and for creating a relevant Common Operating Picture. Incorporating STILMAN's software into a prototype Tactical Action Officers (TAO) workstation as a Tactical Decision Aid (TDA) will allow warfighters to manage their assets more intelligently and effectively. This prototype workstation will be developed using human-centered design principles and will be an open, component-based architecture for combat control systems for future small surface combatants. It will integrate both uninhabited vehicles and onboard sensors and weapon systems across a squadron of small surface combatants. In addition, the hypergame representation of complex operations provides a paradigm for the presentation of a common operating picture to operators and personnel throughout the command hierarchy. In the hypergame technology there are game levels that span the range from the tactical to the global strategy level, with each level informing the others. This same principle will be applied to presenting the relevant common operating picture to operators. Each operator will receive a common operating picture that is appropriate for their level in the command hierarchy. The area covered by this operating picture and the level of detail contained within it will be dependent upon the specific tasks the operator is performing (supervisory vice tactical control) and the level of the operator (or command personnel) within the command hierarchy. Each level will inform the others to keep the picture concurrent and up-to-date.

Solar Photovoltaic DC Systems: Basics and Safety: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

McNutt, Peter F; Sekulic, William R; Dreifuerst, Gary

Solar Photovoltaic (PV) systems are common and growing with 42.4 GW installed capacity in U.S. (almost 15 GW added in 2016). This paper will help electrical workers, and emergency responders understand the basic operating principles and hazards of PV DC arrays. We briefly discuss the following aspects of solar photovoltaic (PV) DC systems: the effects of solar radiation and temperature on output power; PV module testing standards; common system configurations; a simple PV array sizing example; NEC guidelines and other safety features; DC array commissioning, periodic maintenance and testing; arc-flash hazard potential; how electrical workers and emergency responders can andmore » do work safely around PV arrays; do moonlight and artificial lighting pose a real danger; typical safe operating procedures; and other potential DC-system hazards to be aware of. We also present some statistics on PV DC array electrical incidents and injuries. Safe PV array operation is possible with a good understanding of PV DC arrays basics and having good safe operating procedures in place.« less

Analysis of Access Control Policies in Operating Systems

ERIC Educational Resources Information Center

Chen, Hong

2009-01-01

Operating systems rely heavily on access control mechanisms to achieve security goals and defend against remote and local attacks. The complexities of modern access control mechanisms and the scale of policy configurations are often overwhelming to system administrators and software developers. Therefore, mis-configurations are common, and the…

Obstacles to Industrial Implementation of Scanning Systems

Treesearch

Anders Astrom; Olog Broman; John Graffman; Anders Gronlund; Armas Jappinene; Jari Luostarinen; Jan Nystrom; Daniel L. Schmoldt

1998-01-01

Initially the group discussed what is meant by scanning systems. An operational definition was adopted to consider scanning system in the current context to be nontraditional scanning. Where, traditional scanning is defined as scanning that has been industrially operational and relatively common for several years-a mature technology. For example,...

Multifunctional Information Distribution System (MIDS)

DTIC Science & Technology

2015-12-01

UNCLASSIFIED 2 Table of Contents Common Acronyms and Abbreviations for MDAP Programs 3 Program Information 5 Responsible Office 5...Contracts 77 Deliveries and Expenditures 84 Operating and Support Cost 85 Common Acronyms and Abbreviations for MDAP Programs Acq O&M...Acquisition-Related Operations and Maintenance ACAT - Acquisition Category ADM - Acquisition Decision Memorandum APB - Acquisition Program Baseline

40 CFR 89.317 - NOX converter check.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Figure 2 in appendix B of this subpart is a reference for the following paragraphs. (b) Follow good... most common operating range. (e) Introduce into the NOX generator analyzer-system an NO-in-nitrogen (N2) mixture with an NO concentration equal to approximately 80 percent of the most common operating range. The...

40 CFR 89.317 - NOX converter check.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Figure 2 in appendix B of this subpart is a reference for the following paragraphs. (b) Follow good... most common operating range. (e) Introduce into the NOX generator analyzer-system an NO-in-nitrogen (N2) mixture with an NO concentration equal to approximately 80 percent of the most common operating range. The...

Transformational Spaceport and Range Concept of Operations: A Vision to Transform Ground and Launch Operations

NASA Technical Reports Server (NTRS)

2005-01-01

The Transformational Concept of Operations (CONOPS) provides a long-term, sustainable vision for future U.S. space transportation infrastructure and operations. This vision presents an interagency concept, developed cooperatively by the Department of Defense (DoD), the Federal Aviation Administration (FAA), and the National Aeronautics and Space Administration (NASA) for the upgrade, integration, and improved operation of major infrastructure elements of the nation s space access systems. The interagency vision described in the Transformational CONOPS would transform today s space launch infrastructure into a shared system that supports worldwide operations for a variety of users. The system concept is sufficiently flexible and adaptable to support new types of missions for exploration, commercial enterprise, and national security, as well as to endure further into the future when space transportation technology may be sufficiently advanced to enable routine public space travel as part of the global transportation system. The vision for future space transportation operations is based on a system-of-systems architecture that integrates the major elements of the future space transportation system - transportation nodes (spaceports), flight vehicles and payloads, tracking and communications assets, and flight traffic coordination centers - into a transportation network that concurrently accommodates multiple types of mission operators, payloads, and vehicle fleets. This system concept also establishes a common framework for defining a detailed CONOPS for the major elements of the future space transportation system. The resulting set of four CONOPS (see Figure 1 below) describes the common vision for a shared future space transportation system (FSTS) infrastructure from a variety of perspectives.

Common Sense Conversion: Can You Read Me?

ERIC Educational Resources Information Center

Crawford, Walt

1988-01-01

Discusses basic approaches and available software for five categories of file conversion: (1) converting between different computers with different operating systems; (2) converting between different computers with the same operating systems; (3) converting between different applications on the same computer; (4) converting between different…

Creative Analytics of Mission Ops Event Messages

NASA Technical Reports Server (NTRS)

Smith, Dan

2017-01-01

Historically, tremendous effort has been put into processing and displaying mission health and safety telemetry data; and relatively little attention has been paid to extracting information from missions time-tagged event log messages. Todays missions may log tens of thousands of messages per day and the numbers are expected to dramatically increase as satellite fleets and constellations are launched, as security monitoring continues to evolve, and as the overall complexity of ground system operations increases. The logs may contain information about orbital events, scheduled and actual observations, device status and anomalies, when operators were logged on, when commands were resent, when there were data drop outs or system failures, and much much more. When dealing with distributed space missions or operational fleets, it becomes even more important to systematically analyze this data. Several advanced information systems technologies make it appropriate to now develop analytic capabilities which can increase mission situational awareness, reduce mission risk, enable better event-driven automation and cross-mission collaborations, and lead to improved operations strategies: Industry Standard for Log Messages. The Object Management Group (OMG) Space Domain Task Force (SDTF) standards organization is in the process of creating a formal standard for industry for event log messages. The format is based on work at NASA GSFC. Open System Architectures. The DoD, NASA, and others are moving towards common open system architectures for mission ground data systems based on work at NASA GSFC with the full support of the commercial product industry and major integration contractors. Text Analytics. A specific area of data analytics which applies statistical, linguistic, and structural techniques to extract and classify information from textual sources. This presentation describes work now underway at NASA to increase situational awareness through the collection of non-telemetry mission operations information into a common log format and then providing display and analytics tools to provide in-depth assessment of the log contents. The work includes: Common interface formats for acquiring time-tagged text messages Conversion of common files for schedules, orbital events, and stored commands to the common log format Innovative displays to depict thousands of messages on a single display Structured English text queries against the log message data store, extensible to a more mature natural language query capability Goal of speech-to-text and text-to-speech additions to create a personal mission operations assistant to aid on-console operations. A wide variety of planned uses identified by the mission operations teams will be discussed.

NASA Customer Data and Operations System

NASA Technical Reports Server (NTRS)

Butler, Madeline J.; Stallings, William H.

1991-01-01

In addition to the currently provided NASA services such as Communications and Tracking and Data Relay Satellite System services, the NASA's Customer Data and Operations System (CDOS) will provide the following services to the user: Data Delivery Service, Data Archive Service, and CDOS Operations Management Service. This paper describes these services in detail and presents respective block diagrams. The CDOS services will support a variety of multipurpose missions simultaneously with centralized and common hardware and software data-driven systems.

Common Eigenvectors of N Particles' Compatible Observables and its Squeezing Operator

NASA Astrophysics Data System (ADS)

Xu, Shi-Min; Xu, Xing-Lei; Li, Hong-Qi

We construct 2N operators for a N-particle system, namely one center-of-mass coordinate operator, N-1 relative coordinate operators, one total momentum operator and N-1 mass-weighted relative momentum operators, and give common eigenvectors of N compatible observables \\{∑ Ni=1hat {p}i,hat {x}1-hat {x}2,hat {x}2-hat {x}3,hat {x}3-hat {x}4,...; ,hat {x}N-1-hat {x}N\\}, which are composed of N particles' coordinate hat {x}i and momentum hat {p}i. By compatible, we mean such observables can be simultaneously determined. Using the technique of integration within an ordered product of operators (IWOP), we prove that the common eigenvectors are complete and orthonormal, and hereby qualified for making up a representation. This new representation can be applied to solving some dynamic problems in quantum mechanics.

The need for separate operational and engineering user interfaces for command and control of airborne synthetic aperture radar systems

NASA Astrophysics Data System (ADS)

Klein, Laura M.; McNamara, Laura A.

2017-05-01

In this paper, we address the needed components to create usable engineering and operational user interfaces (UIs) for airborne Synthetic Aperture Radar (SAR) systems. As airborne SAR technology gains wider acceptance in the remote sensing and Intelligence, Surveillance, and Reconnaissance (ISR) communities, the need for effective and appropriate UIs to command and control these sensors has also increased. However, despite the growing demand for SAR in operational environments, the technology still faces an adoption roadblock, in large part due to the lack of effective UIs. It is common to find operational interfaces that have barely grown beyond the disparate tools engineers and technologists developed to demonstrate an initial concept or system. While sensor usability and utility are common requirements to engineers and operators, their objectives for interacting with the sensor are different. As such, the amount and type of information presented ought to be tailored to the specific application.

Emergence of a Common Modeling Architecture for Earth System Science (Invited)

NASA Astrophysics Data System (ADS)

Deluca, C.

2010-12-01

Common modeling architecture can be viewed as a natural outcome of common modeling infrastructure. The development of model utility and coupling packages (ESMF, MCT, OpenMI, etc.) over the last decade represents the realization of a community vision for common model infrastructure. The adoption of these packages has led to increased technical communication among modeling centers and newly coupled modeling systems. However, adoption has also exposed aspects of interoperability that must be addressed before easy exchange of model components among different groups can be achieved. These aspects include common physical architecture (how a model is divided into components) and model metadata and usage conventions. The National Unified Operational Prediction Capability (NUOPC), an operational weather prediction consortium, is collaborating with weather and climate researchers to define a common model architecture that encompasses these advanced aspects of interoperability and looks to future needs. The nature and structure of the emergent common modeling architecture will be discussed along with its implications for future model development.

Rainwater harvesting in the United States: a survey of common system practices

EPA Science Inventory

Rainwater harvesting (RWH) systems in the United States vary in terms of design and operation. To better understand common practices in the RWH community and motivation for collecting harvested rainwater, an electronic survey was used to poll members of the American Rainwater Cat...

Integrating a Trusted Computing Base Extension Server and Secure Session Server into the LINUX Operating System

DTIC Science & Technology

2001-09-01

Readily Available Linux has been copyrighted under the terms of the GNU General Public 5 License (GPL)1. This is a license written by the Free...GNOME and KDE . d. Portability Linux is highly compatible with many common operating systems. For...using suitable libraries, Linux is able to run programs written for other operating systems. [Ref. 8] 1 The GNU Project is coordinated by the

Adding Support to the ALMA Common Software for Real-Time Operations through the Usage of a POSIX-Compliant RTOS

NASA Astrophysics Data System (ADS)

Tobar, R. J.; von Brand, H.; Araya, M. A.; Juerges, T.

2010-12-01

The ALMA Common Software (ACS) framework lacks of the real-time capabilities to control the antennas’ instrumentation — as has been probed by previous works — which has lead to non-portable workarounds to the problem. Indeed, the time service used in ACS, based in the Container/Component model, presents plenty of results that confirm this statement. This work addresses the problem of design and integrate a real-time service for ACS, providing to the framework an implementation such that the control operations over the different instruments could be done within real-time constraints. This implementation is compared with the current time service, showing the difference between the two systems when subjecting them to common scenarios. Also, the new implementation is done following the POSIX specification, ensuring interoperability and portability through different operating systems.

A Common Criteria-Based Team Project for High Assurance Secure Systems

DTIC Science & Technology

2005-01-01

experience in the FHM, full system documentation, and plenty of time. The students had little experience and little time. The MINIX operating... MINIX is a very appropriate target for student enhancements. Since the principle objective of Secure Systems is to teach the concepts of...to construct a system when one of the developmental threats is subversion. Because students were studying MINIX in a prerequisite operating systems

ESPC Common Model Architecture

DTIC Science & Technology

2014-09-30

1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. ESPC Common Model Architecture Earth System Modeling...Operational Prediction Capability (NUOPC) was established between NOAA and Navy to develop common software architecture for easy and efficient...development under a common model architecture and other software-related standards in this project. OBJECTIVES NUOPC proposes to accelerate

Defining a region of optimization based on engine usage data

DOEpatents

Jiang, Li; Lee, Donghoon; Yilmaz, Hakan; Stefanopoulou, Anna

2015-08-04

Methods and systems for engine control optimization are provided. One or more operating conditions of a vehicle engine are detected. A value for each of a plurality of engine control parameters is determined based on the detected one or more operating conditions of the vehicle engine. A range of the most commonly detected operating conditions of the vehicle engine is identified and a region of optimization is defined based on the range of the most commonly detected operating conditions of the vehicle engine. The engine control optimization routine is initiated when the one or more operating conditions of the vehicle engine are within the defined region of optimization.

40 CFR 63.1517 - Records

Code of Federal Regulations, 2011 CFR

2011-07-01

... operating parameter value and corrective action taken. (6) For each continuous monitoring system, records... operator may retain records on microfilm, computer disks, magnetic tape, or microfiche; and (3) The owner or operator may report required information on paper or on a labeled computer disk using commonly...

7 CFR 3560.303 - Housing project budgets.

Code of Federal Regulations, 2013 CFR

2013-01-01

... common area systems repairs and maintenance. (F) Snow removal. (G) Elevator repairs and maintenance.... Expenses charged to project operations, whether for management agent services or other expenses, must be... operations and are necessary to carry out successful operations. (i) Housing project expenses must not...

7 CFR 3560.303 - Housing project budgets.

Code of Federal Regulations, 2012 CFR

2012-01-01

... common area systems repairs and maintenance. (F) Snow removal. (G) Elevator repairs and maintenance.... Expenses charged to project operations, whether for management agent services or other expenses, must be... operations and are necessary to carry out successful operations. (i) Housing project expenses must not...

Real Time Metrics and Analysis of Integrated Arrival, Departure, and Surface Operations

NASA Technical Reports Server (NTRS)

Sharma, Shivanjli; Fergus, John

2017-01-01

A real time dashboard was developed in order to inform and present users notifications and integrated information regarding airport surface operations. The dashboard is a supplement to capabilities and tools that incorporate arrival, departure, and surface air-traffic operations concepts in a NextGen environment. As trajectory-based departure scheduling and collaborative decision making tools are introduced in order to reduce delays and uncertainties in taxi and climb operations across the National Airspace System, users across a number of roles benefit from a real time system that enables common situational awareness. In addition to shared situational awareness the dashboard offers the ability to compute real time metrics and analysis to inform users about capacity, predictability, and efficiency of the system as a whole. This paper describes the architecture of the real time dashboard as well as an initial set of metrics computed on operational data. The potential impact of the real time dashboard is studied at the site identified for initial deployment and demonstration in 2017; Charlotte-Douglas International Airport. Analysis and metrics computed in real time illustrate the opportunity to provide common situational awareness and inform users of metrics across delay, throughput, taxi time, and airport capacity. In addition, common awareness of delays and the impact of takeoff and departure restrictions stemming from traffic flow management initiatives are explored. The potential of the real time tool to inform the predictability and efficiency of using a trajectory-based departure scheduling system is also discussed.

SCORPION persistent surveillance system with universal gateway

NASA Astrophysics Data System (ADS)

Coster, Michael; Chambers, Jon; Winters, Michael; Belesi, Joe

2008-04-01

This paper addresses benefits derived from the universal gateway utilized in Northrop Grumman Systems Corporation's (NGSC) SCORPION, a persistent surveillance and target recognition system produced by the Xetron campus in Cincinnati, Ohio. SCORPION is currently deployed in Operations Iraqi Freedom (OIF) and Enduring Freedom (OEF). The SCORPION universal gateway is a flexible, field programmable system that provides integration of over forty Unattended Ground Sensor (UGS) types from a variety of manufacturers, multiple visible and thermal electro-optical (EO) imagers, and numerous long haul satellite and terrestrial communications links, including the Army Research Lab (ARL) Blue Radio. Xetron has been integrating best in class sensors with this universal gateway to provide encrypted data exfiltration and remote sensor command and control since 1998. SCORPION data can be distributed point to point, or to multiple Common Operational Picture (COP) systems, including Command and Control Personal Computer (C2PC), Common Data Interchange Format for the Situational Awareness Display (CDIF/SAD), Force XXI Battle Command Brigade and Below (FBCB2), Defense Common Ground Systems (DCGS), and Remote Automated Position Identification System (RAPIDS).

Mobile Phone Use Behaviors and Postures on Public Transportation Systems.

PubMed

Liang, Huey-Wen; Hwang, Yaw-Huei

2016-01-01

Mobile phones are common in our daily life, but the users' preferences for postures or screen operating styles have not been studied. This was a cross-sectional and observational study. We randomly sampled passengers who used mobile phones on the Mass Rapid Transit (MRT) system in metropolitan Taipei. A checklist was used to observe their body postures and screen operating styles while sitting or standing. As a result, 1,230 subjects from 400 trips were observed. Overall, of all the passengers who were sitting, 41% of them were using mobile phones. The majority of the tasks involved browsing (84%) with their phones in a portrait orientation (93%). Different-hand holding/operating was the most commonly used operating style while sitting (46%) and same-hand holding/operating was the most common while standing (46%). The distribution of screen operating styles was significantly different for those sitting than for those standing and for different genders and age groups. The most frequently observed postures while sitting were having one's trunk against a backrest, feet on the floor and with or without an arm supported (58%). As for the users who were standing, the both- and different-hands groups had a high proportion of arms unsupported, feet on the floor and either their trunk supported or not. In contrast, the same-hand group tended to have their trunk unsupported, were holding a pole or handstrap and had both feet on floor. Further studies are warranted to characterize the ergonomic exposure of these commonly used postures and operating styles, and our results will help guide the selection of experimental conditions for laboratory settings.

Genomic Data Commons launches

Cancer.gov

The Genomic Data Commons (GDC), a unified data system that promotes sharing of genomic and clinical data between researchers, launched today with a visit from Vice President Joe Biden to the operations center at the University of Chicago.

Genomic Data Commons launches - TCGA

Cancer.gov

The Genomic Data Commons (GDC), a unified data system that promotes sharing of genomic and clinical data between researchers, launched today with a visit from Vice President Joe Biden to the operations center at the University of Chicago.

Space Operations Center system analysis study extension. Volume 2: Programmatics and cost

NASA Technical Reports Server (NTRS)

1982-01-01

A summary of Space Operations Center (SOC) orbital space station costs, program options and program recommendations is presented. Program structure, hardware commonality, schedules and program phasing are considered. Program options are analyzed with respect to mission needs, design and technology options, and anticipated funding constraints. Design and system options are discussed.

The Command Operations Dashboard: A Common Operating Picture of the Operators

DTIC Science & Technology

2014-06-01

applications in order to collect data: it utilizes Apache Camel as a light-weight enterprise system bus for routing communications through...Mesmer-Magnus & DeChurch, 2009) to focus their limited resources on those teams needing more support. In terms of productivity , new information

Operational Impacts of Operating Reserve Demand Curves on Production Cost and Reliability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Ibanez, Eduardo; Ela, Erik

The electric power industry landscape is continually evolving. As emerging technologies such as wind, solar, electric vehicles, and energy storage systems become more cost-effective and present in the system, traditional power system operating strategies will need to be reevaluated. The presence of wind and solar generation (commonly referred to as variable generation) may result in an increase in the variability and uncertainty of the net load profile. One mechanism to mitigate this is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increasedmore » variability and uncertainty occurring at finer temporal resolutions. A new operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this paper, and its implications on power system operations are analyzed.« less

Operational Impacts of Operating Reserve Demand Curves on Production Cost and Reliability: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Ibanez, Eduardo; Ela, Erik

The electric power industry landscape is continually evolving. As emerging technologies such as wind, solar, electric vehicles, and energy storage systems become more cost-effective and present in the system, traditional power system operating strategies will need to be reevaluated. The presence of wind and solar generation (commonly referred to as variable generation) may result in an increase in the variability and uncertainty of the net load profile. One mechanism to mitigate this is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increasedmore » variability and uncertainty occurring at finer temporal resolutions. A new operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this paper, and its implications on power system operations are analyzed.« less

Versatile Friction Stir Welding/Friction Plug Welding System

NASA Technical Reports Server (NTRS)

Carter, Robert

2006-01-01

A proposed system of tooling, machinery, and control equipment would be capable of performing any of several friction stir welding (FSW) and friction plug welding (FPW) operations. These operations would include the following: Basic FSW; FSW with automated manipulation of the length of the pin tool in real time [the so-called auto-adjustable pin-tool (APT) capability]; Self-reacting FSW (SRFSW); SR-FSW with APT capability and/or real-time adjustment of the distance between the front and back shoulders; and Friction plug welding (FPW) [more specifically, friction push plug welding] or friction pull plug welding (FPPW) to close out the keyhole of, or to repair, an FSW or SR-FSW weld. Prior FSW and FPW systems have been capable of performing one or two of these operations, but none has thus far been capable of performing all of them. The proposed system would include a common tool that would have APT capability for both basic FSW and SR-FSW. Such a tool was described in Tool for Two Types of Friction Stir Welding (MFS- 31647-1), NASA Tech Briefs, Vol. 30, No. 10 (October 2006), page 70. Going beyond what was reported in the cited previous article, the common tool could be used in conjunction with a plug welding head to perform FPW or FPPW. Alternatively, the plug welding head could be integrated, along with the common tool, into a FSW head that would be capable of all of the aforementioned FSW and FPW operations. Any FSW or FPW operation could be performed under any combination of position and/or force control.

Distributed Common Ground System-Navy Increment 2 (DCGS-N Inc 2)

DTIC Science & Technology

2016-03-01

15 minutes Enter and be Managed in the Network: Reference SvcV-7, Consolidated Afloat Networks and Enterprise Services ( CANES ) CDD, DCGS-N Inc 2...Red, White , Gray Data and Tracks to Command and Control System. Continuous Stream from SCI Common Intelligence Picture to General Service (GENSER...AIS - Automatic Information System AOC - Air Operations Command CANES - Consolidated Afloat Networks and Enterprise Services CID - Center for

ASTER system operating achievement for 15 years on orbit

NASA Astrophysics Data System (ADS)

Inada, Hitomi; Ito, Yoshiyuki; Kikuchi, Masakuni; Sakuma, Fumihiro; Tatsumi, Kenji; Akagi, Shigeki; Ono, Hidehiko

2015-10-01

ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) System is operating more than 15 years since launched on board of NASA's Terra spacecraft in December 1999. ASTER System is composed of 3 radiometers (VNIR (Visible and Near Infrared Radiometer), SWIR (Short-Wave Infrared Radiometer), and TIR (Thermal Infrared Radiometer)), CSP (Common Signal Processor) and MSP (Master Power Supply). This paper describes the ASTER System operating history and the achievement of ASTER System long term operation since the initial checkout operation, the normal operation, and the continuous operation. Through the 15 years operation, ASTER system had totally checked the all subsystems (MPS, VNIR, TIR, SWIR, and CSP) health and safety check using telemetry data trend evaluation, and executed the necessary action. The watch items are monitored as the life control items. The pointing mechanics for VNIR, SWIR and TIR, and the cooler for SWIR and TIR are all operating with any problem for over 15 years. In 2003, ASTER was successfully operated for the lunar calibration. As the future plan, ASTER team is proposing the 2nd lunar calibration before the end of mission.

A Common Communications, Navigation and Surveillance Infrastructure for Accommodating Space Vehicles in the Next Generation Air Transportation System

NASA Technical Reports Server (NTRS)

VanSuetendael, RIchard; Hayes, Alan; Birr, Richard

2008-01-01

Suborbital space flight and space tourism are new potential markets that could significantly impact the National Airspace System (NAS). Numerous private companies are developing space flight capabilities to capture a piece of an emerging commercial space transportation market. These entrepreneurs share a common vision that sees commercial space flight as a profitable venture. Additionally, U.S. space exploration policy and national defense will impose significant additional demands on the NAS. Air traffic service providers must allow all users fair access to limited airspace, while ensuring that the highest levels of safety, security, and efficiency are maintained. The FAA's Next Generation Air Transportation System (NextGen) will need to accommodate spacecraft transitioning to and from space through the NAS. To accomplish this, space and air traffic operations will need to be seamlessly integrated under some common communications, navigation and surveillance (CNS) infrastructure. As part of NextGen, the FAA has been developing the Automatic Dependent Surveillance Broadcast (ADS-B) which utilizes the Global Positioning System (GPS) to track and separate aircraft. Another key component of NextGen, System-Wide Information Management/ Network Enabled Operations (SWIM/NEO), is an open architecture network that will provide NAS data to various customers, system tools and applications. NASA and DoD are currently developing a space-based range (SBR) concept that also utilizes GPS, communications satellites and other CNS assets. The future SBR will have very similar utility for space operations as ADS-B and SWIM has for air traffic. Perhaps the FAA, NASA, and DoD should consider developing a common space-based CNS infrastructure to support both aviation and space transportation operations. This paper suggests specific areas of research for developing a CNS infrastructure that can accommodate spacecraft and other new types of vehicles as an integrated part of NextGen.

23 CFR 973.204 - Management systems requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL LANDS HIGHWAYS MANAGEMENT... system; (2) A process to operate and maintain the management systems and their associated databases; (3... systems shall use databases with a common or coordinated reference system that can be used to geolocate...

23 CFR 973.204 - Management systems requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL LANDS HIGHWAYS MANAGEMENT... system; (2) A process to operate and maintain the management systems and their associated databases; (3... systems shall use databases with a common or coordinated reference system that can be used to geolocate...

Mobile Phone Use Behaviors and Postures on Public Transportation Systems

PubMed Central

Liang, Huey-Wen; Hwang, Yaw-Huei

2016-01-01

Mobile phones are common in our daily life, but the users’ preferences for postures or screen operating styles have not been studied. This was a cross-sectional and observational study. We randomly sampled passengers who used mobile phones on the Mass Rapid Transit (MRT) system in metropolitan Taipei. A checklist was used to observe their body postures and screen operating styles while sitting or standing. As a result, 1,230 subjects from 400 trips were observed. Overall, of all the passengers who were sitting, 41% of them were using mobile phones. The majority of the tasks involved browsing (84%) with their phones in a portrait orientation (93%). Different-hand holding/operating was the most commonly used operating style while sitting (46%) and same-hand holding/operating was the most common while standing (46%). The distribution of screen operating styles was significantly different for those sitting than for those standing and for different genders and age groups. The most frequently observed postures while sitting were having one’s trunk against a backrest, feet on the floor and with or without an arm supported (58%). As for the users who were standing, the both- and different-hands groups had a high proportion of arms unsupported, feet on the floor and either their trunk supported or not. In contrast, the same-hand group tended to have their trunk unsupported, were holding a pole or handstrap and had both feet on floor. Further studies are warranted to characterize the ergonomic exposure of these commonly used postures and operating styles, and our results will help guide the selection of experimental conditions for laboratory settings. PMID:26828797

Intelligent systems and advanced user interfaces for design, operation, and maintenance of command management systems

NASA Technical Reports Server (NTRS)

Potter, William J.; Mitchell, Christine M.

1993-01-01

Historically, command management systems (CMS) have been large and expensive spacecraft-specific software systems that were costly to build, operate, and maintain. Current and emerging hardware, software, and user interface technologies may offer an opportunity to facilitate the initial formulation and design of a spacecraft-specific CMS as well as to develop a more generic CMS system. New technologies, in addition to a core CMS common to a range of spacecraft, may facilitate the training and enhance the efficiency of CMS operations. Current mission operations center (MOC) hardware and software include Unix workstations, the C/C++ programming languages, and an X window interface. This configuration provides the power and flexibility to support sophisticated and intelligent user interfaces that exploit state-of-the-art technologies in human-machine interaction, artificial intelligence, and software engineering. One of the goals of this research is to explore the extent to which technologies developed in the research laboratory can be productively applied in a complex system such as spacecraft command management. Initial examination of some of these issues in CMS design and operation suggests that application of technologies such as intelligent planning, case-based reasoning, human-machine systems design and analysis tools (e.g., operator and designer models), and human-computer interaction tools (e.g., graphics, visualization, and animation) may provide significant savings in the design, operation, and maintenance of the CMS for a specific spacecraft as well as continuity for CMS design and development across spacecraft. The first six months of this research saw a broad investigation by Georgia Tech researchers into the function, design, and operation of current and planned command management systems at Goddard Space Flight Center. As the first step, the researchers attempted to understand the current and anticipated horizons of command management systems at Goddard. Preliminary results are given on CMS commonalities and causes of low re-use, and methods are proposed to facilitate increased re-use.

Advanced Transport Operating System (ATOPS) control display unit software description

NASA Technical Reports Server (NTRS)

Slominski, Christopher J.; Parks, Mark A.; Debure, Kelly R.; Heaphy, William J.

1992-01-01

The software created for the Control Display Units (CDUs), used for the Advanced Transport Operating Systems (ATOPS) project, on the Transport Systems Research Vehicle (TSRV) is described. Module descriptions are presented in a standardized format which contains module purpose, calling sequence, a detailed description, and global references. The global reference section includes subroutines, functions, and common variables referenced by a particular module. The CDUs, one for the pilot and one for the copilot, are used for flight management purposes. Operations performed with the CDU affects the aircraft's guidance, navigation, and display software.

Launch Processing System. [for Space Shuttle

NASA Technical Reports Server (NTRS)

Byrne, F.; Doolittle, G. V.; Hockenberger, R. W.

1976-01-01

This paper presents a functional description of the Launch Processing System, which provides automatic ground checkout and control of the Space Shuttle launch site and airborne systems, with emphasis placed on the Checkout, Control, and Monitor Subsystem. Hardware and software modular design concepts for the distributed computer system are reviewed relative to performing system tests, launch operations control, and status monitoring during ground operations. The communication network design, which uses a Common Data Buffer interface to all computers to allow computer-to-computer communication, is discussed in detail.

Medical Systems Engineering to Support Mars Mission Crew Autonomy

NASA Technical Reports Server (NTRS)

Antonsen, Erik; Mindock, Jennifer

2017-01-01

Human spaceflight missions to Mars face exceptionally challenging resource limitations that far exceed those faced before. Increasing transit times, decreasing opportunity for resupply, communications challenges, and extended time to evacuate a crew to definitive medical care dictate a level of crew autonomy in medical care that is beyond the current medical model. To approach this challenge, a medical systems engineering approach is proposed that relies on a clearly articulated Concept of Operations and risk analysis tools that are in development at NASA. This paper proposes an operational clinical model with key terminology and concepts translated to a controls theory paradigm to frame a common language between clinical and engineering teams. This common language will be used for design and validation of an exploration medical system that is fully integrated into a Mars transit vehicle. This approach merges medical simulation, human factors evaluation techniques, and human-in-the-loop testing in ground based analogs to tie medical hardware and software subsystem performance and overall medical system functionality to metrics of operational medical autonomy. Merging increases in operational clinical autonomy with a more restricted vehicle system resource scenario in interplanetary spaceflight will require an unprecedented level of medical and engineering integration. Full integration of medical capabilities into a Mars vehicle system may require a new approach to integrating medical system design and operations into the vehicle Program structure. Prior to the standing-up of a Mars Mission Program, proof of concept is proposed through the Human Research Program.

47 CFR 32.5280 - Nonregulated operating revenue.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Nonregulated operating revenue. 32.5280 Section 32.5280 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions For Revenue Accounts § 32.5280...

Flow Control and Measurement in Electric Propulsion Systems: Towards an AIAA Reference Standard

NASA Technical Reports Server (NTRS)

Snyder, John Steven; Baldwin, Jeff; Frieman, Jason D.; Walker, Mitchell L. R.; Hicks, Nathan S.; Polzin, Kurt A.; Singleton, James T.

2013-01-01

Accurate control and measurement of propellant flow to a thruster is one of the most basic and fundamental requirements for operation of electric propulsion systems, whether they be in the laboratory or on flight spacecraft. Hence, it is important for the electric propulsion community to have a common understanding of typical methods for flow control and measurement. This paper addresses the topic of propellant flow primarily for the gaseous propellant systems which have dominated laboratory research and flight application over the last few decades, although other types of systems are also briefly discussed. While most flight systems have employed a type of pressure-fed flow restrictor for flow control, both thermal-based and pressure-based mass flow controllers are routinely used in laboratories. Fundamentals and theory of operation of these types of controllers are presented, along with sources of uncertainty associated with their use. Methods of calibration and recommendations for calibration processes are presented. Finally, details of uncertainty calculations are presented for some common calibration methods and for the linear fits to calibration data that are commonly used.

Telepresence system development for application to the control of remote robotic systems

NASA Technical Reports Server (NTRS)

Crane, Carl D., III; Duffy, Joseph; Vora, Rajul; Chiang, Shih-Chien

1989-01-01

The recent developments of techniques which assist an operator in the control of remote robotic systems are described. In particular, applications are aimed at two specific scenarios: The control of remote robot manipulators; and motion planning for remote transporter vehicles. Common to both applications is the use of realistic computer graphics images which provide the operator with pertinent information. The specific system developments for several recently completed and ongoing telepresence research projects are described.

Modeling Load Dynamics to Support Resiliency-based Operations in Low-Inertia Microgrids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuffner, Francis K.; Schneider, Kevin P.; Hansen, Jacob

Microgrids have repeatedly demonstrated the ability to provide uninterrupted service to critical end-use loads during normal outages, severe weather events, and natural disasters. While their ability to provide critical services is well documented, microgrids present a more dynamic operational environment than grid-connected distribution systems. The electrodynamics of a microgrid are commonly driven by the high inertia of rotating generators, which are common in many microgrids. In such high-inertia systems, the impact of end-use load electromechanical dynamics are often not examined. However, with the increased penetration of inverter-based generation with little or no inertia, it is necessary to consider the impactmore » that the dynamics of the end-use loads have on the operations of microgrids, particularly for a resiliency-based operation. These operations include, but are not limited to, switching operations, loss of generating units, and the starting of induction motors. This paper examines the importance of including multi-state electromechanical dynamic models of the end-use load when evaluating the operations of low inertia microgrids, and shows that by properly representing their behavior, it is possible to cost effectively size equipment while supporting resilient operations of critical end-use loads.« less

Operating room myths: what is the evidence for common practices.

PubMed

Pada, Surinder; Perl, Trish M

2015-08-01

In order to ensure patient safety and prevent surgical site infections (SSIs), operating theaters/rooms have evolved into complex, highly technical environments. Prevention of healthcare-associated infections, and strategies to limit patient harm, have gained momentum over the last decade. This article aims to examine and dispute some commonly held beliefs with specific reference to: laminar airflow, noise and operating theater door openings and how these impact SSI. Laminar airflow may not be necessary for prosthetic implant surgery. Some recent data suggest that there may be patient harm. With the development of better surgical techniques and perioperative care, such costly systems may not be needed. Operating rooms with a high number of door openings have also been shown to experience higher SSI rates, as have operating rooms with high noise levels. These may serve as surrogate markers for operating room discipline. Initiatives which target these areas may be worth considering when devising strategies to reduce SSIs. Improved surveillance systems for SSIs are needed and should include operating theater airflow type. This will allow further analysis of the effect of laminar air flow on SSIs and provide evidence for a decisive recommendation. Cultivating a culture of good operating theater discipline may also reduce SSIs.

Modeling Load Dynamics to Support Resiliency-based Operations in Low-Inertia Microgrids

DOE PAGES

Tuffner, Francis K.; Schneider, Kevin P.; Hansen, Jacob; ...

2018-03-07

Microgrids have repeatedly demonstrated the ability to provide uninterrupted service to critical end-use loads during normal outages, severe weather events, and natural disasters. While their ability to provide critical services is well documented, microgrids present a more dynamic operational environment than grid-connected distribution systems. The electrodynamics of a microgrid are commonly driven by the high inertia of rotating generators, which are common in many microgrids. In such high-inertia systems, the impact of end-use load electromechanical dynamics are often not examined. However, with the increased penetration of inverter-based generation with little or no inertia, it is necessary to consider the impactmore » that the dynamics of the end-use loads have on the operations of microgrids, particularly for a resiliency-based operation. These operations include, but are not limited to, switching operations, loss of generating units, and the starting of induction motors. This paper examines the importance of including multi-state electromechanical dynamic models of the end-use load when evaluating the operations of low inertia microgrids, and shows that by properly representing their behavior, it is possible to cost effectively size equipment while supporting resilient operations of critical end-use loads.« less

Local reduction of certain wave operators to one-dimensional form

NASA Technical Reports Server (NTRS)

Roe, Philip

1994-01-01

It is noted that certain common linear wave operators have the property that linear variation of the initial data gives rise to one-dimensional evolution in a plane defined by time and some direction in space. The analysis is given For operators arising in acoustics, electromagnetics, elastodynamics, and an abstract system.

Detailed requirements document for common software of shuttle program information management system

NASA Technical Reports Server (NTRS)

Everette, J. M.; Bradfield, L. D.; Horton, C. L.

1975-01-01

Common software was investigated as a method for minimizing development and maintenance cost of the shuttle program information management system (SPIMS) applications while reducing the time-frame of their development. Those requirements satisfying these criteria are presented along with the stand-alone modules which may be used directly by applications. The SPIMS applications operating on the CYBER 74 computer, are specialized information management systems which use System 2000 as a data base manager. Common software provides the features to support user interactions on a CRT terminal using form input and command response capabilities. These features are available as subroutines to the applications.

Delays in the operating room: signs of an imperfect system.

PubMed

Wong, Janice; Khu, Kathleen Joy; Kaderali, Zul; Bernstein, Mark

2010-06-01

Delays in the operating room have a negative effect on its efficiency and the working environment. In this prospective study, we analyzed data on perioperative system delays. One neurosurgeon prospectively recorded all errors, including perioperative delays, for consecutive patients undergoing elective procedures from May 2000 to February 2009. We analyzed the prevalence, causes and impact of perioperative system delays that occurred in one neurosurgeon's practice. A total of 1531 elective surgical cases were performed during the study period. Delays were the most common type of error (33.6%), and more than half (51.4%) of all cases had at least 1 delay. The most common cause of delay was equipment failure. The first cases of the day and cranial cases had more delays than subsequent cases and spinal cases, respectively. A delay in starting the first case was associated with subsequent delays. Delays frequently occur in the operating room and have a major effect on patient flow and resource utilization. Thorough documentation of perioperative delays provides a basis for the development of solutions for improving operating room efficiency and illustrates the principles underlying the causes of operating room delays across surgical disciplines.

47 CFR 32.6530 - Network operations expense.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Network operations expense. 32.6530 Section 32.6530 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions for Expense Accounts § 32.6530 Network...

47 CFR 32.6530 - Network operations expense.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Network operations expense. 32.6530 Section 32.6530 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions for Expense Accounts § 32.6530 Network...

14 CFR 125.213 - Miscellaneous equipment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... provided for transferring an instrument from its primary operating system to an alternative system, the...) A windshield wiper or equivalent for each pilot station. (c) A power supply and distribution system... distribution system fails. The use of common elements in the system may be approved if the Administrator finds...

14 CFR 125.213 - Miscellaneous equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... provided for transferring an instrument from its primary operating system to an alternative system, the...) A windshield wiper or equivalent for each pilot station. (c) A power supply and distribution system... distribution system fails. The use of common elements in the system may be approved if the Administrator finds...

14 CFR 125.213 - Miscellaneous equipment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... provided for transferring an instrument from its primary operating system to an alternative system, the...) A windshield wiper or equivalent for each pilot station. (c) A power supply and distribution system... distribution system fails. The use of common elements in the system may be approved if the Administrator finds...

14 CFR 125.213 - Miscellaneous equipment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... provided for transferring an instrument from its primary operating system to an alternative system, the...) A windshield wiper or equivalent for each pilot station. (c) A power supply and distribution system... distribution system fails. The use of common elements in the system may be approved if the Administrator finds...

14 CFR 125.213 - Miscellaneous equipment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... provided for transferring an instrument from its primary operating system to an alternative system, the...) A windshield wiper or equivalent for each pilot station. (c) A power supply and distribution system... distribution system fails. The use of common elements in the system may be approved if the Administrator finds...

The implementation of fail-operative functions in integrated digital avionics systems

NASA Technical Reports Server (NTRS)

Osoer, S. S.

1976-01-01

System architectures which incorporate fail operative flight guidance functions within a total integrated avionics complex are described. It is shown that the mixture of flight critical and nonflight critical functions within a common computer complex is an efficient solution to the integration of navigation, guidance, flight control, display, and flight management. Interfacing subsystems retain autonomous capability to avoid vulnerability to total avionics system shutdown as a result of only a few failures.

PRAIS: Distributed, real-time knowledge-based systems made easy

NASA Technical Reports Server (NTRS)

Goldstein, David G.

1990-01-01

This paper discusses an architecture for real-time, distributed (parallel) knowledge-based systems called the Parallel Real-time Artificial Intelligence System (PRAIS). PRAIS strives for transparently parallelizing production (rule-based) systems, even when under real-time constraints. PRAIS accomplishes these goals by incorporating a dynamic task scheduler, operating system extensions for fact handling, and message-passing among multiple copies of CLIPS executing on a virtual blackboard. This distributed knowledge-based system tool uses the portability of CLIPS and common message-passing protocols to operate over a heterogeneous network of processors.

Digital ultrasonic signal processing: Primary ultrasonics task and transducer characterization use and detailed description

NASA Technical Reports Server (NTRS)

Hammond, P. L.

1979-01-01

This manual describes the use of the primary ultrasonics task (PUT) and the transducer characterization system (XC) for the collection, processing, and recording of data received from a pulse-echo ultrasonic system. Both PUT and XC include five primary functions common to many real-time data acquisition systems. Some of these functions are implemented using the same code in both systems. The solicitation and acceptance of operator control input is emphasized. Those operations not under user control are explained.

RFID Technology for Continuous Monitoring of Physiological Signals in Small Animals.

PubMed

Volk, Tobias; Gorbey, Stefan; Bhattacharyya, Mayukh; Gruenwald, Waldemar; Lemmer, Björn; Reindl, Leonhard M; Stieglitz, Thomas; Jansen, Dirk

2015-02-01

Telemetry systems enable researchers to continuously monitor physiological signals in unrestrained, freely moving small rodents. Drawbacks of common systems are limited operation time, the need to house the animals separately, and the necessity of a stable communication link. Furthermore, the costs of the typically proprietary telemetry systems reduce the acceptance. The aim of this paper is to introduce a low-cost telemetry system based on common radio frequency identification technology optimized for battery-independent operational time, good reusability, and flexibility. The presented implant is equipped with sensors to measure electrocardiogram, arterial blood pressure, and body temperature. The biological signals are transmitted as digital data streams. The device is able of monitoring several freely moving animals housed in groups with a single reader station. The modular concept of the system significantly reduces the costs to monitor multiple physiological functions and refining procedures in preclinical research.

ISACC in Operations

DTIC Science & Technology

2014-06-01

19th floor of a Hotel to overlook the entire event. Page 12 of 17 Figure 6: The SPF Operations Centre overlooking the Event Lessons...have a cheap system to help them solve their immediate operational needs. b. Medium enterprises, that need to have quick customization of the...Optimize” tools to help them advance their current operations to a higher service satisfaction level seen by the public. 32. Common across all

The Secure Distributed Operating System Design Project

DTIC Science & Technology

1988-06-01

a di- verse group of people . Its organization isolates different aspects of the project, such as expected results, preliminary results, and technical...modeled after these procedures. " Automation: computers are commonly used to automate tasks previously performed by people ; many of these tasks are... people commonly con- sidered the threats anticipated to the system and mechanisms that are used to prevent those threats. Both hardware and software

Robotics for Nuclear Material Handling at LANL:Capabilities and Needs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harden, Troy A; Lloyd, Jane A; Turner, Cameron J

Nuclear material processing operations present numerous challenges for effective automation. Confined spaces, hazardous materials and processes, particulate contamination, radiation sources, and corrosive chemical operations are but a few of the significant hazards. However, automated systems represent a significant safety advance when deployed in place of manual tasks performed by human workers. The replacement of manual operations with automated systems has been desirable for nearly 40 years, yet only recently are automated systems becoming increasingly common for nuclear materials handling applications. This paper reviews several automation systems which are deployed or about to be deployed at Los Alamos National Laboratory formore » nuclear material handling operations. Highlighted are the current social and technological challenges faced in deploying automated systems into hazardous material handling environments and the opportunities for future innovations.« less

Common spaceborne multicomputer operating system and development environment

NASA Technical Reports Server (NTRS)

Craymer, L. G.; Lewis, B. F.; Hayes, P. J.; Jones, R. L.

1994-01-01

A preliminary technical specification for a multicomputer operating system is developed. The operating system is targeted for spaceborne flight missions and provides a broad range of real-time functionality, dynamic remote code-patching capability, and system fault tolerance and long-term survivability features. Dataflow concepts are used for representing application algorithms. Functional features are included to ensure real-time predictability for a class of algorithms which require data-driven execution on an iterative steady state basis. The development environment supports the development of algorithm code, design of control parameters, performance analysis, simulation of real-time dataflow applications, and compiling and downloading of the resulting application.

Automated space vehicle control for rendezvous proximity operations

NASA Technical Reports Server (NTRS)

Lea, Robert N.

1988-01-01

Rendezvous during the unmanned space exploration missions, such as a Mars Rover/Sample Return will require a completely automatic system from liftoff to docking. A conceptual design of an automated rendezvous, proximity operations, and docking system is being implemented and validated at the Johnson Space Center (JSC). The emphasis is on the progress of the development and testing of a prototype system for control of the rendezvous vehicle during proximity operations that is currently being developed at JSC. Fuzzy sets are used to model the human capability of common sense reasoning in decision making tasks and such models are integrated with the expert systems and engineering control system technology to create a system that performs comparably to a manned system.

Automated space vehicle control for rendezvous proximity operations

NASA Technical Reports Server (NTRS)

Lea, Robert N.

1988-01-01

Rendezvous during the unmanned space exploration missions, such as a Mars Rover/Sample Return will require a completely automatic system from liftoff to docking. A conceptual design of an automated rendezvous, proximity operations, and docking system is being implemented and validated at the Johnson Space Center (JSC). The emphasis is on the progress of the development and testing of a prototype system for control of the rendezvous vehicle during proximity operations that is currently being developed at JSC. Fuzzy sets are used to model the human capability of common sense reasoning in decision-making tasks and such models are integrated with the expert systems and engineering control system technology to create a system that performs comparably to a manned system.

47 CFR 27.1134 - Protection of Federal Government operations.

Code of Federal Regulations, 2013 CFR

2013-10-01

....1134 Section 27.1134 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES 1710-1755 MHz, 2110-2155 MHz, 2000-2020 MHz, and... Defense (DoD) operates communications systems in the 1710-1755 MHz band at 16 protected facilities...

47 CFR 32.7240 - Operating other taxes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Operating other taxes. 32.7240 Section 32.7240 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS..., gross receipts, franchise and capital stock taxes; this account shall also reflect subsequent...

Machine & electrical double control air dryer for vehicle air braking system

NASA Astrophysics Data System (ADS)

Zhang, Xuan; Yang, Liu; Wang, Xian Yan; Tan, Xiao Yan; Wang, Wei

2017-09-01

As is known to all, a vehicle air brake system, in which usually contains moisture. To solve the problem, it is common to use air dryer to dry compressed air effectively and completely remove the moisture and oil of braking system. However, the existing air dryer is not suitable for all commercial vehicles. According to the operational status of the new energy vehicles in the initial operating period, the structure design principle of the machine & electric control air dryer is expounded from the aspects of the structure and operating principle, research & development process.

HVAC SYSTEMS IN THE CURRENT STOCK OF US K-12 SCHOOLS

EPA Science Inventory

The report summarizes information on heating, ventilating, an air- conditioning (HVAC) systems commonly found in U. S. school buildings and the effect that operating these systems has on indoor radon levels. The report describes the ability of various HVAC systems to pressurize a...

HVAC SYSTEMS IN THE CURRENT STOCK OF U.S. K-12 SCHOOLS

EPA Science Inventory

The report summarizes information on heating, ventilating, an air- conditioning (HVAC) systems commonly found in U. S. school buildings and the effect that operating these systems has on indoor radon levels. The report describes the ability of various HVAC systems to pressurize a...

Extending the littoral battlespace (ELB)

NASA Astrophysics Data System (ADS)

McKinney, Edward J.

1999-07-01

The ELB program is a joint Advanced Concept Technology Demonstration funded by the Navy, Marine Corps and the Office of the Secretary of Defence, and managed by the Naval Research. ELB is based on the new warfare paradigm defined by 'joint vision 2010, and on concepts developed by the Navy and Marine Corps in 'From the Sea', 'Forward...from the Sea', 'Ship to Objective Maneuver (STOM)', and 'Operational Maneuver from the Sea'. The objective of ELB is to demonstrate effective operation of dispersed forces in a variety of littoral environments, and to provide those forces timely remote fire support. Successful operation will depend on achieving a common situational awareness among a mobile, distributed command and control, a shortened sensor- to-shooter timeline, and effective utilization of all information source. The glue to hold this system of systems together is a reliable wide band communications system and network infrastructure. This paper will describe the overall architecture of ELB and focus on the core command and control functions associated with achieving a common situational awareness.

Initial Test Results of a Dual Closed-Brayton-Cycle Power Conversion System

NASA Technical Reports Server (NTRS)

Johnson, Paul K.; Mason, Lee S.

2007-01-01

The dual Brayton power conversion system constructed for NASA Glenn Research Center (GRC) was acceptance tested April 2007 at Barber-Nichols, Inc., Arvada, Colorado. This uniquely configured conversion system is built around two modified commercial Capstone C30 microturbines and employs two closed-Brayton-cycle (CBC) converters sharing a common gas inventory and common heat source. Because both CBCs share the gas inventory, behavior of one CBC has an impact on the performance of the other CBC, especially when one CBC is standby or running at a different shaft speed. Testing performed to date includes the CBCs operating at equal and unequal shaft speeds. A test was also conducted where one CBC was capped off and the other was operated as a single CBC converter. The dual Brayton configuration generated 10.6 kWe at 75 krpm and a turbine inlet temperature of 817 K. Single Brayton operation generated 14.8 kWe at 90 krpm and a turbine inlet temperature of 925 K.

Simultaneous overpass off nadir (SOON): a method for unified calibration/validation across IEOS and GEOSS system of systems

NASA Astrophysics Data System (ADS)

Ardanuy, Philip; Bergen, Bill; Huang, Allen; Kratz, Gene; Puschell, Jeff; Schueler, Carl; Walker, Joe

2006-08-01

The US operates a diverse, evolving constellation of research and operational environmental satellites, principally in polar and geosynchronous orbits. Our current and enhanced future domestic remote sensing capability is complemented by the significant capabilities of our current and potential future international partners. In this analysis, we define "success" through the data customers' "eyes": participating in the sufficient and continuously improving satisfaction of their mission responsibilities. To successfully fuse together observations from multiple simultaneous platforms and sensors into a common, self-consistent, operational environment requires that there exist a unified calibration and validation approach. Here, we consider develop a concept for an integrating framework for absolute accuracy; long-term stability; self-consistency among sensors, platforms, techniques, and observing systems; and validation and characterization of performance. Across all systems, this is a non-trivial problem. Simultaneous Nadir Overpasses, or SNO's, provide a proven intercomparison technique: simultaneous, collocated, co-angular measurements. Many systems have off-nadir elements, or effects, that must be calibrated. For these systems, the nadir technique constrains the process. We define the term "SOON," for simultaneous overpass off nadir. We present a target architecture and sensitivity analysis for the affordable, sustainable implementation of a global SOON calibration/validation network that can deliver the much-needed comprehensive, common, self-consistent operational picture in near-real time, at an affordable cost.

A New Kind of Shift Operators for Infinite Circular and Spherical Wells

DOE PAGES

Sun, Guo-Hua; Launey, K. D.; Dytrych, T.; ...

2014-01-01

A new kind of smore » hift operators for infinite circular and spherical wells is identified. These shift operators depend on all spatial variables of quantum systems and connect some eigenstates of confined systems of different radii R sharing energy levels with a common eigenvalue. In circular well, the momentum operators P ± = P x ± i P y play the role of shift operators. The P x and P y operators, the third projection of the orbital angular momentum operator L z , and the Hamiltonian H form a complete set of commuting operators with the SO(2) symmetry. In spherical well, the shift operators establish a novel relation between ψ l m ( r ) and ψ ( l ± 1 ) ( m ± 1 ) ( r ) .« less

Fail-safe bidirectional valve driver

NASA Technical Reports Server (NTRS)

Fujimoto, H.

1974-01-01

Cross-coupled diodes are added to commonly used bidirectional valve driver circuit to protect circuit and power supply. Circuit may be used in systems requiring fail-safe bidirectional valve operation, particularly in chemical- and petroleum-processing control systems and computer-controlled hydraulic or pneumatic systems.

47 CFR 27.1134 - Protection of Federal Government operations.

Code of Federal Regulations, 2014 CFR

2014-10-01

....1134 Section 27.1134 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES 1695-1710 MHz, 1710-1755 MHz, 1755-1780 MHz, 2110... band. The Department of Defense (DoD) operates communications systems in the 1710-1755 MHz band at 16...

47 CFR 32.7240 - Operating other taxes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS... of the cost of the items to which the taxes relate. (g) Taxes on rented telecommunications plant... shall be charged by the lessee to the appropriate Plant Specific Operations Expense account. [51 FR...

Safety validation test equipment operation

NASA Astrophysics Data System (ADS)

Kurosaki, Tadaaki; Watanabe, Takashi

1992-08-01

An overview of the activities conducted on safety validation test equipment operation for materials used for NASA manned missions is presented. Safety validation tests, such as flammability, odor, offgassing, and so forth were conducted in accordance with NASA-NHB-8060.1C using test subjects common with those used by NASA, and the equipment used were qualified for their functions and performances in accordance with NASDA-CR-99124 'Safety Validation Test Qualification Procedures.' Test procedure systems were established by preparing 'Common Procedures for Safety Validation Test' as well as test procedures for flammability, offgassing, and odor tests. The test operation organization chaired by the General Manager of the Parts and Material Laboratory of NASDA (National Space Development Agency of Japan) was established, and the test leaders and operators in the organization were qualified in accordance with the specified procedures. One-hundred-one tests had been conducted so far by the Parts and Material Laboratory according to the request submitted by the manufacturers through the Space Station Group and the Safety and Product Assurance for Manned Systems Office.

Operator assistant systems - An experimental approach using a telerobotics application

NASA Technical Reports Server (NTRS)

Boy, Guy A.; Mathe, Nathalie

1993-01-01

This article presents a knowledge-based system methodology for developing operator assistant (OA) systems in dynamic and interactive environments. This is a problem both of training and design, which is the subject of this article. Design includes both design of the system to be controlled and design of procedures for operating this system. A specific knowledge representation is proposed for representing the corresponding system and operational knowledge. This representation is based on the situation recognition and analytical reasoning paradigm. It tries to make explicit common factors involved in both human and machine intelligence, including perception and reasoning. An OA system based on this representation has been developed for space telerobotics. Simulations have been carried out with astronauts and the resulting protocols have been analyzed. Results show the relevance of the approach and have been used for improving the knowledge representation and the OA architecture.

A reconfigurable common spare for co-located direct television broadcasting satellites

NASA Astrophysics Data System (ADS)

Roederer, A.; Fromm, H.-H.; Berretta, G.

1984-10-01

Spare spacecraft are needed to assure continuous operation in broadcasting services provided with the aid of satellites. The present investigation is concerned with the employment of a common spare approach in which two or three countries share one or several spare spacecraft that can support or temporarily replace any of the prime satellites. Such common spares would have to be reconfigurable to adapt their antenna coverage and polarization, as well as their operating frequencies and possibly their RF output power, to the corresponding parameters assigned to the country to be served. The considered concept is discussed, taking into account questions related to system and transponder, a repointable antenna with a few feed horns, a fixed antenna (apart from fine pointing) with more feeds, and a reconfigurable broadcast payload for a common spare. A common spare for France, Germany, and Italy is considered along with a common spare for the United Kingdom and Spain.

CrossTalk: The Journal of Defense Software Engineering. Volume 23, Number 2, March/April 2010

DTIC Science & Technology

2010-04-01

SDLC phase. 4. Developing secure software depends on understanding the operational con- text in which it will be used. This con- text includes... its development . BSI leverages the Common Weakness Enumeration (CWE) and the Common Attack Pattern Enumeration and Classification (CAPEC) efforts. To...system integrators providing sys- tems (both IT and warfighting) to the Concept Refinement Technology Development System Development and

NATO initial common operational picture capability project

NASA Astrophysics Data System (ADS)

Fanti, Laura; Beach, David

2002-08-01

The Common Operational Picture (COP) capability can be defined as the ability to display on a single screen integrated views of the Recognized Maritime, Air and Ground Pictures, enriched by other tactical data, such as theater plans, assets, intelligence and logistics information. The purpose of the COP capability is to provide military forces a comprehensive view of the battle space, thereby enhancing situational awareness and the decision-making process across the military command and control spectrum. The availability of a COP capability throughout the command structure is a high priority operational requirement in NATO. A COP capability for NATO is being procured and implemented in an incremental way within the NATO Automated Information System (Bi-SC AIS) Functional Services programme under the coordination of the NATO Consultation, Command and Control Agency (NC3A) Integrated Programme Team 5 (IPT5). The NATO Initial COP (iCOP) capability project, first step of this evolutionary procurement, will provide an initial COP capability to NATO in a highly pragmatic and low-risk fashion, by using existing operational communications infrastructure and NATO systems, i.e. the NATO-Wide Integrated Command and Control Software for Air Operations (ICC), the Maritime Command and Control Information System (MCCIS), and the Joint Operations and Intelligence Information System (JOIIS), which will provide respectively the Recognized Air, Maritime and Ground Pictures. This paper gives an overview of the NATO Initial COP capability project, including its evolutionary implementation approach, and describes the technical solution selected to satisfy the urgent operational requirement in a timely and cost effective manner.

Presentation of Class 1 designs for a family of commuter airplanes

NASA Technical Reports Server (NTRS)

Creighton, Tom; Dragush, George; Hendrich, Louis; Hensley, Doug; Morgan, Louise; Oxendine, Charles; Remen, John; Robinson, Terry; Russell, Mark; Swift, Jerry

1986-01-01

The Class 1 configuration designs of a family of commuter aircraft are presented. The proposed aircraft will have a capacity of from 25 to 100 passengers. They are to have the following common features: (1) 2 aft fuselage mounted engines; (2) a low wing; (3) a T-tail type empennage; and (4) a tricycle type landing gear. A family concept is introduced to achieve structural, systems and handling quality commonality throughout. Implementing commonality can substantially reduce manufacturing and production costs. By achieving common system designs, maintenance costs can be reduced by permitting airlines to stock a smaller inventory of spares. Therefore, the higher degree of commonality, the lower the direct operating and life cycle costs. The attempt to implement some of the commonality requirements has caused configuration design problems, i.e., the twin-body concept was introduced. Design data are compared to existing aircraft, and the extent of structural, systems and handling qualities achieved are reviewed.

Real Time Metrics and Analysis of Integrated Arrival, Departure, and Surface Operations

NASA Technical Reports Server (NTRS)

Sharma, Shivanjli; Fergus, John

2017-01-01

To address the Integrated Arrival, Departure, and Surface (IADS) challenge, NASA is developing and demonstrating trajectory-based departure automation under a collaborative effort with the FAA and industry known Airspace Technology Demonstration 2 (ATD-2). ATD-2 builds upon and integrates previous NASA research capabilities that include the Spot and Runway Departure Advisor (SARDA), the Precision Departure Release Capability (PDRC), and the Terminal Sequencing and Spacing (TSAS) capability. As trajectory-based departure scheduling and collaborative decision making tools are introduced in order to reduce delays and uncertainties in taxi and climb operations across the National Airspace System, users of the tools across a number of roles benefit from a real time system that enables common situational awareness. A real time dashboard was developed to inform and present users notifications and integrated information regarding airport surface operations. The dashboard is a supplement to capabilities and tools that incorporate arrival, departure, and surface air-traffic operations concepts in a NextGen environment. In addition to shared situational awareness, the dashboard offers the ability to compute real time metrics and analysis to inform users about capacity, predictability, and efficiency of the system as a whole. This paper describes the architecture of the real time dashboard as well as an initial proposed set of metrics. The potential impact of the real time dashboard is studied at the site identified for initial deployment and demonstration in 2017: Charlotte-Douglas International Airport (CLT). The architecture of implementing such a tool as well as potential uses are presented for operations at CLT. Metrics computed in real time illustrate the opportunity to provide common situational awareness and inform users of system delay, throughput, taxi time, and airport capacity. In addition, common awareness of delays and the impact of takeoff and departure restrictions stemming from traffic flow management initiatives are explored. The potential of the real time tool to inform users of the predictability and efficiency of using a trajectory-based departure scheduling system is also discussed.

Experimental and Analytical Performance of a Dual Brayton Power Conversion System

NASA Technical Reports Server (NTRS)

Lavelle, Thomas A.; Hervol, David S.; Briggs, Maxwell; Owen, A. Karl

2009-01-01

The interactions between two closed Brayton cycle (CBC) power conversion units (PCU) which share a common gas inventory and heat source have been studied experimentally using the Dual Brayton Power Conversion System (DBPCS) and analytically using the Closed- Cycle System Simulation (CCSS) computer code. Selected operating modes include steady-state operation at equal and unequal shaft speeds and various start-up scenarios. Equal shaft speed steady-state tests were conducted for heater exit temperatures of 840 to 950 K and speeds of 50 to 90 krpm, providing a system performance map. Unequal shaft speed steady-state testing over the same operating conditions shows that the power produced by each Brayton is sensitive to the operating conditions of the other due to redistribution of gas inventory. Startup scenarios show that starting the engines one at a time can dramatically reduce the required motoring energy. Although the DBPCS is not considered a flight-like system, these insights, as well as the operational experience gained from operating and modeling this system provide valuable information for the future development of Brayton systems.

Object-Oriented Technology-Based Software Library for Operations of Water Reclamation Centers

NASA Astrophysics Data System (ADS)

Otani, Tetsuo; Shimada, Takehiro; Yoshida, Norio; Abe, Wataru

SCADA systems in water reclamation centers have been constructed based on hardware and software that each manufacturer produced according to their design. Even though this approach used to be effective to realize real-time and reliable execution, it is an obstacle to cost reduction about system construction and maintenance. A promising solution to address the problem is to set specifications that can be used commonly. In terms of software, information model approach has been adopted in SCADA systems in other field, such as telecommunications and power systems. An information model is a piece of software specification that describes a physical or logical object to be monitored. In this paper, we propose information models for operations of water reclamation centers, which have not ever existed. In addition, we show the feasibility of the information model in terms of common use and processing performance.

ATLAS, an integrated structural analysis and design system. Volume 2: System design document

NASA Technical Reports Server (NTRS)

Erickson, W. J. (Editor)

1979-01-01

ATLAS is a structural analysis and design system, operational on the Control Data Corporation 6600/CYBER computers. The overall system design, the design of the individual program modules, and the routines in the ATLAS system library are described. The overall design is discussed in terms of system architecture, executive function, data base structure, user program interfaces and operational procedures. The program module sections include detailed code description, common block usage and random access file usage. The description of the ATLAS program library includes all information needed to use these general purpose routines.

47 CFR 22.959 - Rules governing processing of applications for initial systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... initial systems. 22.959 Section 22.959 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES PUBLIC MOBILE SERVICES Cellular Radiotelephone Service § 22.959 Rules governing processing of applications for initial systems. Pending applications for authority to operate the first...

Power consumption analysis of operating systems for wireless sensor networks.

PubMed

Lajara, Rafael; Pelegrí-Sebastiá, José; Perez Solano, Juan J

2010-01-01

In this paper four wireless sensor network operating systems are compared in terms of power consumption. The analysis takes into account the most common operating systems--TinyOS v1.0, TinyOS v2.0, Mantis and Contiki--running on Tmote Sky and MICAz devices. With the objective of ensuring a fair evaluation, a benchmark composed of four applications has been developed, covering the most typical tasks that a Wireless Sensor Network performs. The results show the instant and average current consumption of the devices during the execution of these applications. The experimental measurements provide a good insight into the power mode in which the device components are running at every moment, and they can be used to compare the performance of different operating systems executing the same tasks.

Skill accreditation system for laparoscopic gastroenterologic surgeons in Japan.

PubMed

Mori, Toshiyuki; Kimura, Taizo; Kitajima, Masaki

2010-01-01

The Japan Society for Endoscopic Surgery (JSES) has established an Endoscopic Surgical Skill Qualification System and started examination in 2004. Non-edited videotapes were assessed by two judges in a double-blinded fashion with strict criteria. Two kinds of criteria, namely common and procedure-specific, were prepared. The common criteria were designed to evaluate set-ups, autonomy of the operator, display of the surgical field, recognition of surgical anatomy, co-operation of the surgical team. The procedure-specific criteria were made to assess the operation in a step-by-step fashion. In total, out of 1.114 surgeons who were assessed by this qualification system over a period of four years, 537 (48.2%) have been accredited. The qualification rate in each surgical field has remained at the same level of 40 to 50% to date. Inter-rater agreement of two judges was low at 0.31 in the first year, but improved with revision of the criteria and consensus meetings. Surgeons assessed by this system as qualified experienced less frequent complications when compared to those who failed. This system has impacted on the improvement and standardization of laparoscopic surgery in Japan.

The U.S. Air Force Transformation Flight Plan

DTIC Science & Technology

2003-11-01

at Buckley Air Force Base, Colorado. Reserve Associate and Active Associate units have proven that this concept works and benef its the Active and...munitions manufactured from nano-particles, whose virtually all-surface structure yields unprecedented “burn-rates” (extreme explosiveness), promise far...systems for a common operating system, and a suite of remotely operated sensors, weapons, and robotics . Also included are a group of non-lethal weapon

Space Shuttle utilization characteristics with special emphasis on payload design, economy of operation and effective space exploitation

NASA Technical Reports Server (NTRS)

Turner, D. N.

1981-01-01

The reusable manned Space Shuttle has made new and innovative payload planning a reality and opened the door to a variety of payload concepts formerly unavailable in routine space operations. In order to define the payload characteristics and program strategies, current Shuttle-oriented programs are presented: NASA's Space Telescope, the Long Duration Exposure Facility, the West German Shuttle Pallet Satellite, and the Goddard Space Flight Center's Multimission Modular Spacecraft. Commonality of spacecraft design and adaptation for specific mission roles minimizes payload program development and STS integration costs. Commonality of airborne support equipment assures the possibility of multiple program space operations with the Shuttle. On-orbit maintenance and repair was suggested for the module and system levels. Program savings from 13 to over 50% were found obtainable by the Shuttle over expendable launch systems, and savings from 17 to 45% were achievable by introducing reuse into the Shuttle-oriented programs.

Observation of Biological Tissues Using Common Path Optical Coherence Tomography with Gold Coated Conical Tip Lens Fiber

NASA Astrophysics Data System (ADS)

Taguchi, K.; Sugiyama, J.; Totsuka, M.; Imanaka, S.

2012-03-01

In this paper, we proposed a high lateral resolution common-path Fourier domain optical coherence tomography(OCT) system with the use of a chemically etched single mode fiber. In our experiments, single mode optical fiber for 1310nm was used for preparing the tapered tips. Our system used a conical microlens that was chemically etched by selective chemical etching technique using an etching solution of buffered hydrofluoric acid (BHF). From experimental results, we verified that our proposed optical coherence tomography system could operate as a common-path Fourier domain OCT system and conical tip lens fiber was very useful for a high lateral resolution common-path Fourier domain OCT system. Furthermore, we could observe a surface of paramecium bursaria and symbiotic chlorella in the paramecium bursaria using gold coated conical-tip fiber in the water.

The Effects of High-Altitude Electromagnetic Pulse (HEMP) on Telecommunications Assets

DTIC Science & Technology

1988-06-01

common to a whole class of switches. 5ESS switch software controls the operating system, call processing, and system administration andgmaintenance...LEVEL (ky/rn)3 (a). Mean Fraction of Preset Calls Dropped Due to Induced Transients3 1.0 W -o35kVhM (36 EVENTS) 5-40 kV/M (13 EVENTS) IAUTOMATIC ...eel PERIPHRAL UNIT BUS,IMNA The entire 4ESS system is controlled by the 1A processor. The processor monitors and controls the operation of the

An Integration of the Turbojet and Single-Throat Ramjet

NASA Technical Reports Server (NTRS)

Trefny, C. J.; Benson, T. J.

1995-01-01

A turbine-engine-based hybrid propulsion system is described. Turbojet engines are integrated with a single-throat ramjet so as to minimize variable geometry and eliminate redundant propulsion components. The result is a simple, lightweight system that is operable from takeoff to high Mach numbers. Non-afterburning turbojets are mounted within the ramjet duct. They exhaust through a converging-diverging (C-D) nozzle into a common ramjet burner section. At low speed the ejector effect of the C-D nozzle aerodynamically isolates the relatively high pressure turbojet exhaust stream from the ramjet duct. As the Mach number increases, and the turbojet pressure ratio diminishes, the system is biased naturally toward ramjet operation. The common ramjet burner is fueled with hydrogen and thermally choked, thus avoiding the weight and complexity of a variable geometry, split-flow exhaust system. The mixed-compression supersonic inlet and subsonic diffuser are also common to both the turbojet and ramjet cycles. As the compressor face total temperature limit is approached, a two-position flap within the inlet is actuated, which closes off the turbojet inlet and provides increased internal contraction for ramjet operation. Similar actuation of the turbojet C-D nozzle flap completes the enclosure of the turbojet. Performance of the hybrid system is compared herein to that of the discrete turbojet and ramjet engines from takeoff to Mach 6. The specific impulse of the hybrid system falls below that of the non-integrated turbojet and ramjet because of ejector and Rayleigh losses. Unlike the discrete turbojet or ramjet however, the hybrid system produces thrust over the entire Mach number range. An alternate mode of operation for takeoff and low speed is also described. In this mode the C-D nozzle flap is deflected to a third position, which closes off the ramjet duct and eliminates the ejector total pressure loss.

ELISA, a demonstrator environment for information systems architecture design

NASA Technical Reports Server (NTRS)

Panem, Chantal

1994-01-01

This paper describes an approach of reusability of software engineering technology in the area of ground space system design. System engineers have lots of needs similar to software developers: sharing of a common data base, capitalization of knowledge, definition of a common design process, communication between different technical domains. Moreover system designers need to simulate dynamically their system as early as possible. Software development environments, methods and tools now become operational and widely used. Their architecture is based on a unique object base, a set of common management services and they host a family of tools for each life cycle activity. In late '92, CNES decided to develop a demonstrative software environment supporting some system activities. The design of ground space data processing systems was chosen as the application domain. ELISA (Integrated Software Environment for Architectures Specification) was specified as a 'demonstrator', i.e. a sufficient basis for demonstrations, evaluation and future operational enhancements. A process with three phases was implemented: system requirements definition, design of system architectures models, and selection of physical architectures. Each phase is composed of several activities that can be performed in parallel, with the provision of Commercial Off the Shelves Tools. ELISA has been delivered to CNES in January 94, currently used for demonstrations and evaluations on real projects (e.g. SPOT4 Satellite Control Center). It is on the way of new evolutions.

A Common Cockpit Training System

DTIC Science & Technology

2005-01-01

a learning environment where students can practice ASW via free - play simulated tactical situations while receiving feedback and instruction customized...Mission Display and includes free play simulation capability to maximize training. This intelligent tutoring system (ITS) will observe the operator’s

Technology requirements and readiness for very large vehicles

NASA Technical Reports Server (NTRS)

Conner, D. W.

1979-01-01

Common concerns of very large vehicles in the areas of economics, transportation system interfaces and operational problems were reviewed regarding their influence on vehicle configurations and technology. Fifty-four technology requirements were identified which are judged to be unique, or particularly critical, to very large vehicles. The requirements were about equally divided among the four general areas of aero/hydrodynamics, propulsion and acoustics, structures, and vehicle systems and operations. The state of technology readiness was judged to be poor to fair for slightly more than one half of the requirements. In the classic disciplinary areas, the state of technology readiness appears to be more advanced than for vehicle systems and operations.

Protection against hostile algorithms in UNIX software

NASA Astrophysics Data System (ADS)

Radatti, Peter V.

1996-03-01

Protection against hostile algorithms contained in Unix software is a growing concern without easy answers. Traditional methods used against similar attacks in other operating system environments such as MS-DOS or Macintosh are insufficient in the more complex environment provided by Unix. Additionally, Unix provides a special and significant problem in this regard due to its open and heterogeneous nature. These problems are expected to become both more common and pronounced as 32 bit multiprocess network operating systems become popular. Therefore, the problems experienced today are a good indicator of the problems and the solutions that will be experienced in the future, no matter which operating system becomes predominate.

Prevalence of Salmonella enterica, Listeria monocytogenes, and pathogenic Escherichia coli in bulk tank milk and milk filters from US dairy operations in the National Animal Health Monitoring System Dairy 2014 study.

PubMed

Sonnier, Jakeitha L; Karns, Jeffrey S; Lombard, Jason E; Kopral, Christine A; Haley, Bradd J; Kim, Seon-Woo; Van Kessel, Jo Ann S

2018-03-01

The dairy farm environment is a well-documented reservoir for zoonotic pathogens such as Salmonella enterica, Shiga-toxigenic Escherichia coli, and Listeria monocytogenes, and humans may be exposed to these pathogens via consumption of unpasteurized milk and dairy products. As part of the National Animal Health Monitoring System Dairy 2014 study, bulk tank milk (BTM, n = 234) and milk filters (n = 254) were collected from a total of 234 dairy operations in 17 major dairy states and analyzed for the presence of these pathogens. The invA gene was detected in samples from 18.5% of operations and Salmonella enterica was isolated from 18.0% of operations. Salmonella Dublin was detected in 0.7% of operations. Sixteen Salmonella serotypes were isolated, and the most common serotypes were Cerro, Montevideo, and Newport. Representative Salmonella isolates (n = 137) were tested against a panel of 14 antimicrobials. Most (85%) were pansusceptible; the remaining were resistant to 1 to 9 antimicrobials, and within the resistant strains the most common profile was resistance to ampicillin/clavulanic acid, ampicillin, cefoxitin, ceftiofur, ceftriaxone, chloramphenicol, streptomycin, sulfisoxazole, and tetracycline. Listeria spp. were isolated from 19.9% of operations, and L. monocytogenes was isolated from 3.0% of operations. Serogroups 1/2a and 1/2b were the most common, followed by 4b and 4a. One or more E. coli virulence genes were detected in the BTM from 30.5% of operations and in the filters from 75.3% of operations. A combination of stx 2 , eaeA, and γ-tir genes was detected in the BTM from 0.5% of operations and in the filters from 6.6% of operations. The results of this study indicate an appreciable prevalence of bacterial pathogens in BTM and filters, including serovars known to infect humans. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Fundamental procedures of geographic information analysis

NASA Technical Reports Server (NTRS)

Berry, J. K.; Tomlin, C. D.

1981-01-01

Analytical procedures common to most computer-oriented geographic information systems are composed of fundamental map processing operations. A conceptual framework for such procedures is developed and basic operations common to a broad range of applications are described. Among the major classes of primitive operations identified are those associated with: reclassifying map categories as a function of the initial classification, the shape, the position, or the size of the spatial configuration associated with each category; overlaying maps on a point-by-point, a category-wide, or a map-wide basis; measuring distance; establishing visual or optimal path connectivity; and characterizing cartographic neighborhoods based on the thematic or spatial attributes of the data values within each neighborhood. By organizing such operations in a coherent manner, the basis for a generalized cartographic modeling structure can be developed which accommodates a variety of needs in a common, flexible and intuitive manner. The use of each is limited only by the general thematic and spatial nature of the data to which it is applied.

Achieving Better Buying Power for Mobile Open Architecture Software Systems Through Diverse Acquisition Scenarios

DTIC Science & Technology

2016-04-30

software (OSS) and proprietary (CSS) software elements or remote services (Scacchi, 2002, 2010), eventually including recent efforts to support Web ...specific platforms, including those operating on secured Web /mobile devices.  Common Development Technology provides AC development tools and common...transition to OA systems and OSS software elements, specifically for Web and Mobile devices within the realm of C3CB. OA, Open APIs, OSS, and CSS OA

The Aegean Sea marine security decision support system

NASA Astrophysics Data System (ADS)

Perivoliotis, L.; Krokos, G.; Nittis, K.; Korres, G.

2011-05-01

As part of the integrated ECOOP (European Coastal Sea Operational observing and Forecasting System) project, HCMR upgraded the already existing standalone Oil Spill Forecasting System for the Aegean Sea, initially developed for the Greek Operational Oceanography System (POSEIDON), into an active element of the European Decision Support System (EuroDeSS). The system is accessible through a user friendly web interface where the case scenarios can be fed into the oil spill drift model component, while the synthetic output contains detailed information about the distribution of oil spill particles and the oil spill budget and it is provided both in text based ECOOP common output format and as a series of sequential graphics. The main development steps that were necessary for this transition were the modification of the forcing input data module in order to allow the import of other system products which are usually provided in standard formats such as NetCDF and the transformation of the model's calculation routines to allow use of current, density and diffusivities data in z instead of sigma coordinates. During the implementation of the Aegean DeSS, the system was used in operational mode in order support the Greek marine authorities in handling a real accident that took place in North Aegean area. Furthermore, the introduction of common input and output files by all the partners of EuroDeSS extended the system's interoperability thus facilitating data exchanges and comparison experiments.

The Aegean sea marine security decision support system

NASA Astrophysics Data System (ADS)

Perivoliotis, L.; Krokos, G.; Nittis, K.; Korres, G.

2011-10-01

As part of the integrated ECOOP (European Coastal Sea Operational observing and Forecasting System) project, HCMR upgraded the already existing standalone Oil Spill Forecasting System for the Aegean Sea, initially developed for the Greek Operational Oceanography System (POSEIDON), into an active element of the European Decision Support System (EuroDeSS). The system is accessible through a user friendly web interface where the case scenarios can be fed into the oil spill drift model component, while the synthetic output contains detailed information about the distribution of oil spill particles and the oil spill budget and it is provided both in text based ECOOP common output format and as a series of sequential graphics. The main development steps that were necessary for this transition were the modification of the forcing input data module in order to allow the import of other system products which are usually provided in standard formats such as NetCDF and the transformation of the model's calculation routines to allow use of current, density and diffusivities data in z instead of sigma coordinates. During the implementation of the Aegean DeSS, the system was used in operational mode in order to support the Greek marine authorities in handling a real accident that took place in North Aegean area. Furthermore, the introduction of common input and output files by all the partners of EuroDeSS extended the system's interoperability thus facilitating data exchanges and comparison experiments.

Dataset for forensic analysis of B-tree file system.

PubMed

Wani, Mohamad Ahtisham; Bhat, Wasim Ahmad

2018-06-01

Since B-tree file system (Btrfs) is set to become de facto standard file system on Linux (and Linux based) operating systems, Btrfs dataset for forensic analysis is of great interest and immense value to forensic community. This article presents a novel dataset for forensic analysis of Btrfs that was collected using a proposed data-recovery procedure. The dataset identifies various generalized and common file system layouts and operations, specific node-balancing mechanisms triggered, logical addresses of various data structures, on-disk records, recovered-data as directory entries and extent data from leaf and internal nodes, and percentage of data recovered.

The Significance of the Understanding of Balance and Coordination in Self-Cognitive "Bio-Electro-Biblio/Info" Systems.

ERIC Educational Resources Information Center

Tsai, Bor-sheng

1991-01-01

Examines the information communication process and proposes a fuzzy commonality model for improving communication systems. Topics discussed include components of an electronic information programing and processing system and the flow of the formation and transfer of information, including DOS (disk operating system) commands, computer programing…

A Better Management Information System Is Needed to Promote Information Sharing, Effective Planning, and Coordination of Afghanistan Reconstruction Activities

DTIC Science & Technology

2009-07-30

management information systems for collecting data on their reconstruction activities, but there is no single management information system that provides...spreadsheets, presentations, and other ad hoc reports. An integrated management information system that provides a common operating picture of all U.S

An exploratory study to determine the integrated technological air transportation system ground requirements of liquid-hydrogen-fueled subsonic, long-haul civil air transports

NASA Technical Reports Server (NTRS)

1976-01-01

A baseline air terminal concept was developed which permitted airlines and the airport to operate JP- or LH2-fueled aircraft at common terminal gates. The concept included installation of a hydrogen liquefaction and storage facility on airport property, as well as the fuel distribution system. The capital investment and hydrogen-related operating costs to the airlines were estimated.

State of the art survey of network operating systems development

NASA Technical Reports Server (NTRS)

1985-01-01

The results of the State-of-the-Art Survey of Network Operating Systems (NOS) performed for Goddard Space Flight Center are presented. NOS functional characteristics are presented in terms of user communication data migration, job migration, network control, and common functional categories. Products (current or future) as well as research and prototyping efforts are summarized. The NOS products which are revelant to the space station and its activities are evaluated.

20th International Seapower Symposium

DTIC Science & Technology

2013-01-01

System ( aIS ) we need to build common operations and the concept of operations of that. The Maritime Safety and Security Information System (MSSIS)— we...closed factories, unemployment , and social stress in ar- eas far removed from the initial disruption. The value-added of goods with a “Made in China...germany and Korea as close runners-up. The United States itself is also a major contributor to that production pattern. a Federal Reserve Bank of

One Way of Testing a Distributed Processor

NASA Technical Reports Server (NTRS)

Edstrom, R.; Kleckner, D.

1982-01-01

Launch processing for Space Shuttle is checked out, controlled, and monitored with new system. Entire system can be exercised by two computer programs--one in master console and other in each of operations consoles. Control program in each operations console detects change in status and begins task initiation. All of front-end processors are exercised from consoles through common data buffer, and all data are logged to processed-data recorder for posttest analysis.

A Future Vision for Remotely Piloted Aircraft: Leveraging Interoperability and Networked Operations

DTIC Science & Technology

2013-06-21

over the next 25 years  Balances the effects envisioned in the USAF UAS Flight Plan with the reality of constrained resources and ambitious...theater-level unmanned systems must detect, avoid, or counter threats – operating from permissive to highly contested access in all weather...Rapid Reaction Group II/III SUAS Unit  Light Footprint, Low Cost ISR Option  Networked Autonomous C2 System  Air-Launched SUAS  Common

Graphics-oriented Battlefield Tracking Systems: U.S. Army and Air Force Interoperability

DTIC Science & Technology

2010-12-10

systems. There are hundreds of applications used to control joint air operations, to synchronize land forces, and to develop a common operational...plan and synchronize the employment of 5 combat power (Department of Defense 2010c, II-9). The subsystem that facilitates graphics-oriented...during the battle recounts, “we had so many different assets up in the air . . . they were stacked up on so many different levels” ( Jung 2009

Space Station data management system architecture

NASA Technical Reports Server (NTRS)

Mallary, William E.; Whitelaw, Virginia A.

1987-01-01

Within the Space Station program, the Data Management System (DMS) functions in a dual role. First, it provides the hardware resources and software services which support the data processing, data communications, and data storage functions of the onboard subsystems and payloads. Second, it functions as an integrating entity which provides a common operating environment and human-machine interface for the operation and control of the orbiting Space Station systems and payloads by both the crew and the ground operators. This paper discusses the evolution and derivation of the requirements and issues which have had significant effect on the design of the Space Station DMS, describes the DMS components and services which support system and payload operations, and presents the current architectural view of the system as it exists in October 1986; one-and-a-half years into the Space Station Phase B Definition and Preliminary Design Study.

Principles of Sociology in Systems Engineering

NASA Technical Reports Server (NTRS)

Watson, Michael D.; Andrews, James G.; Larsen, Jordan A.

2017-01-01

Systems engineering involves both the integration of the system and the integration of the disciplines which develop and operate the system. Integrating the disciplines is a sociological effort to bring together different groups, often with different terminology, to achieve a common goal, the system. The focus for the systems engineer is information flow through the organization, between the disciplines, to ensure the system is developed and operated with all relevant information informing system decisions. Robert K. Merton studied the sociological principles of the sciences and the sociological principles he developed apply to systems engineering. Concepts such as specification of ignorance, common terminology, opportunity structures, role-sets, and the reclama (reconsideration) process are all important sociological approaches that should be employed by the systems engineer. In bringing the disciplines together, the systems engineer must also be wary of social ambivalence, social anomie, social dysfunction, insider-outsider behavior, unintended consequences, and the self-fulfilling prophecy. These sociological principles provide the systems engineer with key approaches to manage the information flow through the organization as the disciplines are integrated and share their information. This also helps identify key sociological barriers to information flow through the organization. This paper will discuss this theoretical basis for the application of sociological principles to systems engineering.

Grid Integration Studies: Advancing Clean Energy Planning and Deployment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katz, Jessica; Chernyakhovskiy, Ilya

2016-07-01

Integrating significant variable renewable energy (VRE) into the grid requires an evolution in power system planning and operation. To plan for this evolution, power system stakeholders can undertake grid integration studies. This Greening the Grid document reviews grid integration studies, common elements, questions, and guidance for system planners.

Regenerating an Arsenic Removal Iron-Based Adsorptive Media System, Part 2: Performance and Cost

EPA Science Inventory

The replacement of exhausted, adsorptive media used to remove arsenic from drinking water accounts for approximately 80% of the total operational and maintenance (O/M) costs of this commonly used small system technology. The results of three, full scale system studies of an on-s...

Single module pressurized fuel cell turbine generator system

DOEpatents

George, Raymond A.; Veyo, Stephen E.; Dederer, Jeffrey T.

2001-01-01

A pressurized fuel cell system (10), operates within a common pressure vessel (12) where the system contains fuel cells (22), a turbine (26) and a generator (98) where preferably, associated oxidant inlet valve (52), fuel inlet valve (56) and fuel cell exhaust valve (42) are outside the pressure vessel.

47 CFR 32.2311 - Station apparatus.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS..., Operator systems, or Account 2341, Large Private Branch Exchanges, as appropriate. (e) Station apparatus... from this account and included in Account 1220, Inventories. (h) Embedded CPE is that equipment or...

47 CFR 32.2311 - Station apparatus.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS..., Operator systems, or Account 2341, Large Private Branch Exchanges, as appropriate. (e) Station apparatus... from this account and included in Account 1220, Inventories. (h) Embedded CPE is that equipment or...

47 CFR 32.2311 - Station apparatus.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS..., Operator systems, or Account 2341, Large Private Branch Exchanges, as appropriate. (e) Station apparatus... from this account and included in Account 1220, Inventories. (h) Embedded CPE is that equipment or...

NASA UAS Traffic Management National Campaign Operations across Six UAS Test Sites

NASA Technical Reports Server (NTRS)

Rios, Joseph; Mulfinger, Daniel; Homola, Jeff; Venkatesan, Priya

2016-01-01

NASA's Unmanned Aircraft Systems Traffic Management research aims to develop policies, procedures, requirements, and other artifacts to inform the implementation of a future system that enables small drones to access the low altitude airspace. In this endeavor, NASA conducted a geographically diverse flight test in conjunction with the FAA's six unmanned aircraft systems Test Sites. A control center at NASA Ames Research Center autonomously managed the airspace for all participants in eight states as they flew operations (both real and simulated). The system allowed for common situational awareness across all stakeholders, kept traffic procedurally separated, offered messages to inform the participants of activity relevant to their operations. Over the 3- hour test, 102 flight operations connected to the central research platform with 17 different vehicle types and 8 distinct software client implementations while seamlessly interacting with simulated traffic.

Laying a Common Foundation for Success

ERIC Educational Resources Information Center

Rothman, Robert

2012-01-01

For decades, the American elementary and secondary education system has operated somewhat as the railroads did before Lincoln's day, with each state setting its own expectations for what students should know and be able to do. To address that problem, nearly every state, with little fanfare, has adopted the Common Core State Standards for student…

Department of Homeland Security: Assessments of Selected Complex Acquisitions

DTIC Science & Technology

2010-06-01

10 The two nonmajor programs selected—the Biosurveillance Common...Management Directive AD 102-01, and approves acquisitions to proceed to their next acquisition life- cycle phases upon satisfaction of applicable ...programs are Biosurveillance Common Operating Network and the Integrated Public Alert and Warning System. BioWatch Generation-3 had not started

Analysis of failure and maintenance experiences of motor operated valves in a Finnish nuclear power plant

NASA Astrophysics Data System (ADS)

Simola, Kaisa; Laakso, Kari

1992-01-01

Eight years of operating experiences of 104 motor operated closing valves in different safety systems in nuclear power units were analyzed in a systematic way. The qualitative methods used were Failure Mode and Effect Analysis (FMEA) and Maintenance Effects and Criticality Analysis (MECA). These reliability engineering methods are commonly used in the design stage of equipment. The successful application of these methods for analysis and utilization of operating experiences was demonstrated.

Assessment of Delivery Accuracy in an Operational-Like Environment

NASA Technical Reports Server (NTRS)

Sharma, Shivanjli; Wynnyk, Mitch

2016-01-01

In order to enable arrival management concepts and solutions in a Next Generation Air Transportation System (NextGen) environment, ground-based sequencing and scheduling functions were developed to support metering operations in the National Airspace System. These sequencing and scheduling tools are designed to assist air traffic controllers in developing an overall arrival strategy, from enroute down to the terminal area boundary. NASA developed a ground system concept and protoype capability called Terminal Sequencing and Spacing (TSAS) to extend metering operations into the terminal area to the runway. To demonstrate the use of these scheduling and spacing tools in an operational-like environment, the FAA, NASA, and MITRE conducted an Operational Integration Assessment (OIA) of a prototype TSAS system at the FAA's William J. Hughes Technical Center (WJHTC). This paper presents an analysis of the arrival management strategies utilized and delivery accuracy achieved during the OIA. The analysis demonstrates how en route preconditioning, in various forms, and schedule disruptions impact delivery accuracy. As the simulation spanned both enroute and terminal airspace, the use of Ground Interval Management - Spacing (GIM-S) enroute speed advisories was investigated. Delivery accuracy was measured as the difference between the Scheduled Time of Arrival (STA) and the Actual Time of Arrival (ATA). The delivery accuracy was computed across all runs conducted during the OIA, which included deviations from nominal operations which are known to commonly occur in real operations, such as schedule changes and missed approaches. Overall, 83% of all flights were delivered into the terminal airspace within +/- 30 seconds of their STA and 94% of flights were delivered within +/- 60 seconds. The meter fix delivery accuracy standard deviation was found to be between 36 and 55 seconds across all arrival procedures. The data also showed when schedule disruptions were excluded, the percentage of aircraft delivered within +/- 30 seconds was between 85 and 90% across the various arrival procedures at the meter fix. This paper illustrates the ability to meet new delivery accuracy requirements in an operational-like environment using operational systems and NATCA controller participants, while also including common events that might cause disruptions to the schedule and overall system.

The Evolvable Advanced Multi-Mission Operations System (AMMOS): Making Systems Interoperable

NASA Technical Reports Server (NTRS)

Ko, Adans Y.; Maldague, Pierre F.; Bui, Tung; Lam, Doris T.; McKinney, John C.

2010-01-01

The Advanced Multi-Mission Operations System (AMMOS) provides a common Mission Operation System (MOS) infrastructure to NASA deep space missions. The evolution of AMMOS has been driven by two factors: increasingly challenging requirements from space missions, and the emergence of new IT technology. The work described in this paper focuses on three key tasks related to IT technology requirements: first, to eliminate duplicate functionality; second, to promote the use of loosely coupled application programming interfaces, text based file interfaces, web-based frameworks and integrated Graphical User Interfaces (GUI) to connect users, data, and core functionality; and third, to build, develop, and deploy AMMOS services that are reusable, agile, adaptive to project MOS configurations, and responsive to industrially endorsed information technology standards.

Legacy System Improvements for the Objective Force

DTIC Science & Technology

2001-08-14

Less Than 11 lbs • M249 Short Barrel/ Buttstock •Reduced size/length • Com Remotely Op Wpn Sys •Fire Under Armor w/o Turret • IAV Program Spt •Primary...concepts being evaluated Common Remotely Operated Weapons Station(CROWS) Benefits: • Permits under armor operation of crew served weapons for suppression of

7 CFR 1730.62 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... ELECTRIC SYSTEM OPERATIONS AND MAINTENANCE Interconnection of Distributed Resources § 1730.62 Definitions. “Distributed resources” as used in this subpart means sources of electric power that are not directly connected... to the borrower's electric power system through a point of common coupling. Distributed resources...

A parsimonious land data assimilation system for the SMAP/GPM satellite era

USDA-ARS?s Scientific Manuscript database

Land data assimilation systems typically require complex parameterizations in order to: define required observation operators, quantify observing/forecasting errors and calibrate a land surface assimilation model. These parameters are commonly defined in an arbitrary manner and, if poorly specified,...

7 CFR 1730.62 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... ELECTRIC SYSTEM OPERATIONS AND MAINTENANCE Interconnection of Distributed Resources § 1730.62 Definitions. “Distributed resources” as used in this subpart means sources of electric power that are not directly connected... to the borrower's electric power system through a point of common coupling. Distributed resources...

7 CFR 1730.62 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... ELECTRIC SYSTEM OPERATIONS AND MAINTENANCE Interconnection of Distributed Resources § 1730.62 Definitions. “Distributed resources” as used in this subpart means sources of electric power that are not directly connected... to the borrower's electric power system through a point of common coupling. Distributed resources...

7 CFR 1730.62 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... ELECTRIC SYSTEM OPERATIONS AND MAINTENANCE Interconnection of Distributed Resources § 1730.62 Definitions. “Distributed resources” as used in this subpart means sources of electric power that are not directly connected... to the borrower's electric power system through a point of common coupling. Distributed resources...

7 CFR 1730.62 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... ELECTRIC SYSTEM OPERATIONS AND MAINTENANCE Interconnection of Distributed Resources § 1730.62 Definitions. “Distributed resources” as used in this subpart means sources of electric power that are not directly connected... to the borrower's electric power system through a point of common coupling. Distributed resources...

Development of thermal control methods for specialized components and scientific instruments at very low temperatures (follow-on)

NASA Technical Reports Server (NTRS)

Wright, J. P.; Wilson, D. E.

1976-01-01

Many payloads currently proposed to be flown by the space shuttle system require long-duration cooling in the 3 to 200 K temperature range. Common requirements also exist for certain DOD payloads. Parametric design and optimization studies are reported for multistage and diode heat pipe radiator systems designed to operate in this temperature range. Also optimized are ground test systems for two long-life passive thermal control concepts operating under specified space environmental conditions. The ground test systems evaluated are ultimately intended to evolve into flight test qualification prototypes for early shuttle flights.

Improved methods for the measurement and modeling of PV module and system performance for all operating conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, D.L.

1995-11-01

The objective of this work was to develop improved performance model for modules and systems for for all operating conditions for use in module specifications, system and BOS component design, and system rating or monitoring. The approach taken was to identify and quantify the influence of dominant factors of solar irradiance, cell temperature, angle-of-incidence; and solar spectrum; use outdoor test procedures to separate the effects of electrical, thermal, and optical performance; use fundamental cell characteristics to improve analysis; and combine factors in simple model using the common variables.

MDA DS COI Spiral 3 - NOA, SILO and ABAC

DTIC Science & Technology

2009-06-01

agencies. The National Plan to Achieve MDA, a by-product of the Maritime Security Policy, established the national maritime common operating picture...information about vessels determined to be of interest by intelligence and operational organizations and is normally classified or highly sensitive. Exposing...makes it available to its users. For Spiral 3, the Coast Guard team, consisting of CG-26, the Operations Systems Center (OSC), and the Coast Guard

Power Consumption Analysis of Operating Systems for Wireless Sensor Networks

PubMed Central

Lajara, Rafael; Pelegrí-Sebastiá, José; Perez Solano, Juan J.

2010-01-01

In this paper four wireless sensor network operating systems are compared in terms of power consumption. The analysis takes into account the most common operating systems—TinyOS v1.0, TinyOS v2.0, Mantis and Contiki—running on Tmote Sky and MICAz devices. With the objective of ensuring a fair evaluation, a benchmark composed of four applications has been developed, covering the most typical tasks that a Wireless Sensor Network performs. The results show the instant and average current consumption of the devices during the execution of these applications. The experimental measurements provide a good insight into the power mode in which the device components are running at every moment, and they can be used to compare the performance of different operating systems executing the same tasks. PMID:22219688

47 CFR 63.02 - Exemptions for extensions of lines and for systems for the delivery of video programming.

Code of Federal Regulations, 2011 CFR

2011-10-01

... systems for the delivery of video programming. 63.02 Section 63.02 Telecommunication FEDERAL... systems for the delivery of video programming. (a) Any common carrier is exempt from the requirements of... with respect to the establishment or operation of a system for the delivery of video programming. [64...

47 CFR 63.02 - Exemptions for extensions of lines and for systems for the delivery of video programming.

Code of Federal Regulations, 2010 CFR

2010-10-01

... systems for the delivery of video programming. 63.02 Section 63.02 Telecommunication FEDERAL... systems for the delivery of video programming. (a) Any common carrier is exempt from the requirements of... with respect to the establishment or operation of a system for the delivery of video programming. [64...

47 CFR 63.02 - Exemptions for extensions of lines and for systems for the delivery of video programming.

Code of Federal Regulations, 2013 CFR

2013-10-01

... systems for the delivery of video programming. 63.02 Section 63.02 Telecommunication FEDERAL... systems for the delivery of video programming. (a) Any common carrier is exempt from the requirements of... with respect to the establishment or operation of a system for the delivery of video programming. [64...

47 CFR 63.02 - Exemptions for extensions of lines and for systems for the delivery of video programming.

Code of Federal Regulations, 2014 CFR

2014-10-01

... systems for the delivery of video programming. 63.02 Section 63.02 Telecommunication FEDERAL... systems for the delivery of video programming. (a) Any common carrier is exempt from the requirements of... with respect to the establishment or operation of a system for the delivery of video programming. [64...

47 CFR 63.02 - Exemptions for extensions of lines and for systems for the delivery of video programming.

Code of Federal Regulations, 2012 CFR

2012-10-01

... systems for the delivery of video programming. 63.02 Section 63.02 Telecommunication FEDERAL... systems for the delivery of video programming. (a) Any common carrier is exempt from the requirements of... with respect to the establishment or operation of a system for the delivery of video programming. [64...

Common MD-IS infrastructure for wireless data technologies

NASA Astrophysics Data System (ADS)

White, Malcolm E.

1995-12-01

The expansion of global networks, caused by growth and acquisition within the commercial sector, is forcing users to move away from proprietary systems in favor of standards-based, open systems architectures. The same is true in the wireless data communications arena, where operators of proprietary wireless data networks have endeavored to convince users that their particular implementation provides the best service. However, most of the vendors touting these solutions have failed to gain the critical mass that might have lead to their technologies' adoption as a defacto standard, and have been held back by a lack of applications and the high cost of mobile devices. The advent of the cellular digital packet data (CDPD) specification and its support by much of the public cellular service industry has set the stage for the ubiquitous coverage of wireless packet data services across the Unites States. Although CDPD was developed for operation over the advanced mobile phone system (AMPS) cellular network, many of the defined protocols are industry standards that can be applied to the construction of a common infrastructure supporting multiple airlink standards. This approach offers overall cost savings and operation efficiency for service providers, hardware, and software developers and end-users alike, and could be equally advantageous for those service operators using proprietary end system protocols, should they wish to migrate towards an open standard.

30 CFR 778.22 - Facilities or structures used in common.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR LEGAL, FINANCIAL, COMPLIANCE, AND RELATED...

Control of intrauterine fluid pressure during operative hysteroscopy.

PubMed

Shirk, G J; Gimpelson, R J

1994-05-01

To evaluate the safety of a commonly used piston pump that controls the infusion pressure of low-viscosity fluids in a continuous-flow hysteroscopic system during operative hysteroscopy. Consecutive patients requiring operative hysteroscopy. Three hospital facilities in the Midwest. Sequential sample of 250 women who underwent operative hysteroscopy. Endometrial ablations, resection of submucosal or pedunculated uterine leiomyomata with or without endometrial ablation, polyp resections, metroplasty, and lysis of synechiae. The most serious complication of operative hysteroscopy is fluid overload due to intravasation into the patient's vascular system. Low-viscosity fluids were infused by the Zimmer Controlled Distention Irrigation System. The instrument uses a closed-feedback loop to monitor cavity pressure and automatically regulates the flow to maintain the set point pressure. It is designed to operate in a pressure range of 0 to 80 mm Hg and at flows in excess of 450 ml/minute. In 250 operative hysteroscopies no fluid complications occurred when intrauterine pressure was maintained below 80 mm Hg. No clinically significant differences in intravasation were seen in any type of operative hysteroscopy. This controlled mechanical pump system with exact intrauterine pressure measurement reduced many technical difficulties associated with low-viscosity media, and created a safe environment for the media's use in operative hysteroscopy.

The Dilemma for USSOCOM: Transitioning SOF-Peculiar to Service-Common

DTIC Science & Technology

2012-02-15

Operations-peculiar (SO-peculiar or SOF-peculiar) to Service-common, while the third implication suggests a lack of “ advertising ”, i.e. the need for a...Portfolio Management ( CPM ) system which seeks to optimize capability investments across the defense enterprise.59 Though CPMs are charged to identify...capabilities as Service-common. Collectively though they do offer several avenues in which SOCOM can “ advertise ” them, and whereby through mutual

Advanced Modular Power Approach to Affordable, Supportable Space Systems

NASA Technical Reports Server (NTRS)

Oeftering, Richard C.; Kimnach, Greg L.; Fincannon, James; Mckissock,, Barbara I.; Loyselle, Patricia L.; Wong, Edmond

2013-01-01

Recent studies of missions to the Moon, Mars and Near Earth Asteroids (NEA) indicate that these missions often involve several distinct separately launched vehicles that must ultimately be integrated together in-flight and operate as one unit. Therefore, it is important to see these vehicles as elements of a larger segmented spacecraft rather than separate spacecraft flying in formation. The evolution of large multi-vehicle exploration architecture creates the need (and opportunity) to establish a global power architecture that is common across all vehicles. The Advanced Exploration Systems (AES) Modular Power System (AMPS) project managed by NASA Glenn Research Center (GRC) is aimed at establishing the modular power system architecture that will enable power systems to be built from a common set of modular building blocks. The project is developing, demonstrating and evaluating key modular power technologies that are expected to minimize non-recurring development costs, reduce recurring integration costs, as well as, mission operational and support costs. Further, modular power is expected to enhance mission flexibility, vehicle reliability, scalability and overall mission supportability. The AMPS project not only supports multi-vehicle architectures but should enable multi-mission capability as well. The AMPS technology development involves near term demonstrations involving developmental prototype vehicles and field demonstrations. These operational demonstrations not only serve as a means of evaluating modular technology but also provide feedback to developers that assure that they progress toward truly flexible and operationally supportable modular power architecture.

The ultimate efficiency of photosensitive systems

NASA Technical Reports Server (NTRS)

Buoncristiani, A. M.; Byvik, C. E.; Smith, B. T.

1981-01-01

These systems have in common two important but not independent features: they can produce a storable fuel, and they are sensitive only to radiant energy with a characteristic absorption spectrum. General analyses of the conversion efficiencies were made using the operational characteristics of each particular system. An efficiency analysis of a generalized system consisting of a blackbody source, a radiant energy converter having a threshold energy and operating temperature, and a reservoir is reported. This analysis is based upon the first and second laws of thermodynamics, and leads to a determination of the limiting or ultimate efficiency for an energy conversion system having a characteristic threshold.

An engineering database management system for spacecraft operations

NASA Technical Reports Server (NTRS)

Cipollone, Gregorio; Mckay, Michael H.; Paris, Joseph

1993-01-01

Studies at ESOC have demonstrated the feasibility of a flexible and powerful Engineering Database Management System in support for spacecraft operations documentation. The objectives set out were three-fold: first an analysis of the problems encountered by the Operations team in obtaining and managing operations documents; secondly, the definition of a concept for operations documentation and the implementation of prototype to prove the feasibility of the concept; and thirdly, definition of standards and protocols required for the exchange of data between the top-level partners in a satellite project. The EDMS prototype was populated with ERS-l satellite design data and has been used by the operations team at ESOC to gather operational experience. An operational EDMS would be implemented at the satellite prime contractor's site as a common database for all technical information surrounding a project and would be accessible by the cocontractor's and ESA teams.

Entropic cohering power in quantum operations

NASA Astrophysics Data System (ADS)

Xi, Zhengjun; Hu, Ming-Liang; Li, Yongming; Fan, Heng

2018-02-01

Coherence is a basic feature of quantum systems and a common necessary condition for quantum correlations. It is also an important physical resource in quantum information processing. In this paper, using relative entropy, we consider a more general definition of the cohering power of quantum operations. First, we calculate the cohering power of unitary quantum operations and show that the amount of distributed coherence caused by non-unitary quantum operations cannot exceed the quantum-incoherent relative entropy between system of interest and its environment. We then find that the difference between the distributed coherence and the cohering power is larger than the quantum-incoherent relative entropy. As an application, we consider the distributed coherence caused by purification.

Delegation control of multiple unmanned systems

NASA Astrophysics Data System (ADS)

Flaherty, Susan R.; Shively, Robert J.

2010-04-01

Maturing technologies and complex payloads coupled with a future objective to reduce the logistics burden of current unmanned aerial systems (UAS) operations require a change to the 2-crew employment paradigm. Increased automation and operator supervisory control of unmanned systems have been advocated to meet the objective of reducing the crew requirements, while managing future technologies. Specifically, a delegation control employment strategy has resulted in reduced workload and higher situation awareness for single operators controlling multiple unmanned systems in empirical studies1,2. Delegation control is characterized by the ability for an operator to call a single "play" that initiates prescribed default actions for each vehicle and associated sensor related to a common mission goal. Based upon the effectiveness of delegation control in simulation, the U.S. Army Aeroflightdynamics Directorate (AFDD) developed a Delegation Control (DelCon) operator interface with voice recognition implementation for play selection, real-time play modification, and play status with automation transparency to enable single operator control of multiple unmanned systems in flight. AFDD successfully demonstrated delegation control in a Troops-in-Contact mission scenario at Ft. Ord in 2009. This summary showcases the effort as a beneficial advance in single operator control of multiple UAS.

10 CFR Appendix N to Part 52 - Standardization of Nuclear Power Plant Designs: Combined Licenses To Construct and Operate...

Code of Federal Regulations, 2012 CFR

2012-01-01

... structures, systems, and components important to radiological health and safety and the common defense and... report on the environmental impacts of the common design. 5. Upon a determination that each application.... 6. The NRC staff shall prepare draft and final environmental impact statements for each of the...

10 CFR 71.4 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... venting, external cooling by an ancillary system, or operational controls during transport. Natural...: The International System of Units (SI) followed or preceded by U.S. standard or customary units. The U... water as a common, contract, or private carrier, or by civil aircraft. Certificate holder means a person...

10 CFR 71.4 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... venting, external cooling by an ancillary system, or operational controls during transport. Natural...: The International System of Units (SI) followed or preceded by U.S. standard or customary units. The U... water as a common, contract, or private carrier, or by civil aircraft. Certificate holder means a person...

10 CFR 71.4 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... venting, external cooling by an ancillary system, or operational controls during transport. Natural...: The International System of Units (SI) followed or preceded by U.S. standard or customary units. The U... water as a common, contract, or private carrier, or by civil aircraft. Certificate holder means a person...

BEARS: a multi-mission anomaly response system

NASA Astrophysics Data System (ADS)

Roberts, Bryce A.

2009-05-01

The Mission Operations Group at UC Berkeley's Space Sciences Laboratory operates a highly automated ground station and presently a fleet of seven satellites, each with its own associated command and control console. However, the requirement for prompt anomaly detection and resolution is shared commonly between the ground segment and all spacecraft. The efficient, low-cost operation and "lights-out" staffing of the Mission Operations Group requires that controllers and engineers be notified of spacecraft and ground system problems around the clock. The Berkeley Emergency Anomaly and Response System (BEARS) is an in-house developed web- and paging-based software system that meets this need. BEARS was developed as a replacement for an existing emergency reporting software system that was too closedsource, platform-specific, expensive, and antiquated to expand or maintain. To avoid these limitations, the new system design leverages cross-platform, open-source software products such as MySQL, PHP, and Qt. Anomaly notifications and responses make use of the two-way paging capabilities of modern smart phones.

An open-source, extensible system for laboratory timing and control

NASA Astrophysics Data System (ADS)

Gaskell, Peter E.; Thorn, Jeremy J.; Alba, Sequoia; Steck, Daniel A.

2009-11-01

We describe a simple system for timing and control, which provides control of analog, digital, and radio-frequency signals. Our system differs from most common laboratory setups in that it is open source, built from off-the-shelf components, synchronized to a common and accurate clock, and connected over an Ethernet network. A simple bus architecture facilitates creating new and specialized devices with only moderate experience in circuit design. Each device operates independently, requiring only an Ethernet network connection to the controlling computer, a clock signal, and a trigger signal. This makes the system highly robust and scalable. The devices can all be connected to a single external clock, allowing synchronous operation of a large number of devices for situations requiring precise timing of many parallel control and acquisition channels. Provided an accurate enough clock, these devices are capable of triggering events separated by one day with near-microsecond precision. We have achieved precisions of ˜0.1 ppb (parts per 109) over 16 s.

An Integrated Planning Representation Using Macros, Abstractions, and Cases

NASA Technical Reports Server (NTRS)

Baltes, Jacky; MacDonald, Bruce

1992-01-01

Planning will be an essential part of future autonomous robots and integrated intelligent systems. This paper focuses on learning problem solving knowledge in planning systems. The system is based on a common representation for macros, abstractions, and cases. Therefore, it is able to exploit both classical and case based techniques. The general operators in a successful plan derivation would be assessed for their potential usefulness, and some stored. The feasibility of this approach was studied through the implementation of a learning system for abstraction. New macros are motivated by trying to improve the operatorset. One heuristic used to improve the operator set is generating operators with more general preconditions than existing ones. This heuristic leads naturally to abstraction hierarchies. This investigation showed promising results on the towers of Hanoi problem. The paper concludes by describing methods for learning other problem solving knowledge. This knowledge can be represented by allowing operators at different levels of abstraction in a refinement.

Modular space vehicle boards, control software, reprogramming, and failure recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judd, Stephen; Dallmann, Nicholas; McCabe, Kevin

A space vehicle may have a modular board configuration that commonly uses some or all components and a common operating system for at least some of the boards. Each modular board may have its own dedicated processing, and processing loads may be distributed. The space vehicle may be reprogrammable, and may be launched without code that enables all functionality and/or components. Code errors may be detected and the space vehicle may be reset to a working code version to prevent system failure.

Identification and Analysis of National Airspace System Resource Constraints

NASA Technical Reports Server (NTRS)

Smith, Jeremy C.; Marien, Ty V.; Viken, Jeffery K.; Neitzke, Kurt W.; Kwa, Tech-Seng; Dollyhigh, Samuel M.; Fenbert, James W.; Hinze, Nicolas K.

2015-01-01

This analysis is the deliverable for the Airspace Systems Program, Systems Analysis Integration and Evaluation Project Milestone for the Systems and Portfolio Analysis (SPA) focus area SPA.4.06 Identification and Analysis of National Airspace System (NAS) Resource Constraints and Mitigation Strategies. "Identify choke points in the current and future NAS. Choke points refer to any areas in the en route, terminal, oceanic, airport, and surface operations that constrain actual demand in current and projected future operations. Use the Common Scenarios based on Transportation Systems Analysis Model (TSAM) projections of future demand developed under SPA.4.04 Tools, Methods and Scenarios Development. Analyze causes, including operational and physical constraints." The NASA analysis is complementary to a NASA Research Announcement (NRA) "Development of Tools and Analysis to Evaluate Choke Points in the National Airspace System" Contract # NNA3AB95C awarded to Logistics Management Institute, Sept 2013.

Mars Surface System Common Capabilities and Challenges for Human Missions

NASA Technical Reports Server (NTRS)

Hoffman, Stephen J.; Toups, Larry

2016-01-01

NASA has begun a process to identify and evaluate candidate locations where humans could land, live and work on the martian surface. These locations are referred to as Exploration Zones (EZs). Given current mission concepts, an EZ is a collection of Regions of Interest (ROIs) that are located within approximately 100 kilometers of a centralized landing site. ROIs are areas that are relevant for scientific investigation and/or development/maturation of capabilities and resources necessary for a sustainable human presence. The EZ also contains a landing site and a habitation site that will be used by multiple human crews during missions to explore and utilize the ROIs within the EZ. In parallel with this process, NASA continues to make progress on the Evolvable Mars Campaign examining alternatives that can pioneer an extended human presence on Mars that is Earth independent. This involves ongoing assessments of surface systems and operations to enable a permanent, sustainable human presence. Because of the difficulty in getting equipment and supplies to the surface of Mars, part of these assessments involve identifying those systems and processes that can perform in multiple, sometimes completely unrelated, situations. These assessments have been performed in a very generic surface mission carried out at a very generic surface location. As specific candidate EZs are identified it becomes important to evaluate the current suite of surface systems and operations as they are likely to perform for the specific locations and for the types of operations - both scientific and development - that are proposed for these EZs. It is also important to evaluate the proposed EZs for their suitability to be explored or developed given the range of capabilities and constraints for the types of surface systems and operations being considered within the EMC. This means looking at setting up and operating a field station at a central location within the EZ as well as traversing to and exploring the scientific ROIs within the boundaries of the EZ. The proposed paper will describe the current status of common systems and operations as they can be applied to actual EZ locations on Mars. Initially these EZs will be the four locations identified MEPAG's Human Exploration of Mars Science Analysis Group (HEM-SAG) that will be used as representative of the EZs that will emerge from the process that NASA has initiated. An example process that could be commonly applied is an approach for developing a field station site plan that would be demonstrated by applying this process to each of the four HEM-SAG sites. Examples of common systems include (a) mobility systems that can be used to off-load and move payloads to specific locations at the central field station location that could also be used to traverse long distances to reach some of the more remote ROIs or (b) robotic systems that can support various activities (such as system set up and maintenance) at the field station that could also be used to explore scientific ROIs and used to support site-specific ISRU production activities.

On-Orbit Propulsion System Performance of ISS Visiting Vehicles

NASA Technical Reports Server (NTRS)

Martin, Mary Regina M.; Swanson, Robert A.; Kamath, Ulhas P.; Hernandez, Francisco J.; Spencer, Victor

2013-01-01

The International Space Station (ISS) represents the culmination of over two decades of unprecedented global human endeavors to conceive, design, build and operate a research laboratory in space. Uninterrupted human presence in space since the inception of the ISS has been made possible by an international fleet of space vehicles facilitating crew rotation, delivery of science experiments and replenishment of propellants and supplies. On-orbit propulsion systems on both ISS and Visiting Vehicles are essential to the continuous operation of the ISS. This paper compares the ISS visiting vehicle propulsion systems by providing an overview of key design drivers, operational considerations and performance characteristics. Despite their differences in design, functionality, and purpose, all visiting vehicles must adhere to a common set of interface requirements along with safety and operational requirements. This paper addresses a wide variety of methods for satisfying these requirements and mitigating credible hazards anticipated during the on-orbit life of propulsion systems, as well as the seamless integration necessary for the continued operation of the ISS.

Cooling system for a nuclear reactor

DOEpatents

Amtmann, Hans H.

1982-01-01

A cooling system for a gas-cooled nuclear reactor is disclosed which includes at least one primary cooling loop adapted to pass coolant gas from the reactor core and an associated steam generator through a duct system having a main circulator therein, and at least one auxiliary cooling loop having communication with the reactor core and adapted to selectively pass coolant gas through an auxiliary heat exchanger and circulator. The main and auxiliary circulators are installed in a common vertical cavity in the reactor vessel, and a common return duct communicates with the reactor core and intersects the common cavity at a junction at which is located a flow diverter valve operative to effect coolant flow through either the primary or auxiliary cooling loops.

Spectral domain, common path OCT in a handheld PIC based system

NASA Astrophysics Data System (ADS)

Leinse, Arne; Wevers, Lennart; Marchenko, Denys; Dekker, Ronald; Heideman, René G.; Ruis, Roosje M.; Faber, Dirk J.; van Leeuwen, Ton G.; Kim, Keun Bae; Kim, Kyungmin

2018-02-01

Optical Coherence Tomography (OCT) has made it into the clinic in the last decade with systems based on bulk optical components. The next disruptive step will be the introduction of handheld OCT systems. Photonic Integrated Circuit (PIC) technology is the key enabler for this further miniaturization. PIC technology allows signal processing on a stable platform and the implementation of a common path interferometer in that same platform creates a robust fully integrated OCT system with a flexible fiber probe. In this work the first PIC based handheld and integrated common path based spectral domain OCT system is described and demonstrated. The spectrometer in the system is based on an Arrayed Waveguide Grating (AWG) and fully integrated with the CCD and a fiber probe into a system operating at 850 nm. The AWG on the PIC creates a 512 channel spectrometer with a resolution of 0.22 nm enabling a high speed analysis of the full A-scan. The silicon nitride based proprietary waveguide technology (TriPleXTM) enables low loss complex photonic structures from the visible (405 nm) to IR (2350 nm) range, making it a unique candidate for OCT applications. Broadband AWG operation from visible to 1700 nm has been shown in the platform and Photonic Design Kits (PDK) are available enabling custom made designs in a system level design environment. This allows a low threshold entry for designing new (OCT) designs for a broad wavelength range.

Advanced Transport Operating System (ATOPS) color displays software description microprocessor system

NASA Technical Reports Server (NTRS)

Slominski, Christopher J.; Plyler, Valerie E.; Dickson, Richard W.

1992-01-01

This document describes the software created for the Sperry Microprocessor Color Display System used for the Advanced Transport Operating Systems (ATOPS) project on the Transport Systems Research Vehicle (TSRV). The software delivery known as the 'baseline display system', is the one described in this document. Throughout this publication, module descriptions are presented in a standardized format which contains module purpose, calling sequence, detailed description, and global references. The global reference section includes procedures and common variables referenced by a particular module. The system described supports the Research Flight Deck (RFD) of the TSRV. The RFD contains eight cathode ray tubes (CRTs) which depict a Primary Flight Display, Navigation Display, System Warning Display, Takeoff Performance Monitoring System Display, and Engine Display.

Dynamic Exergy Method for Evaluating the Control and Operation of Oxy-Combustion Boiler Island Systems.

PubMed

Jin, Bo; Zhao, Haibo; Zheng, Chuguang; Liang, Zhiwu

2017-01-03

Exergy-based methods are widely applied to assess the performance of energy conversion systems; however, these methods mainly focus on a certain steady-state and have limited applications for evaluating the control impacts on system operation. To dynamically obtain the thermodynamic behavior and reveal the influences of control structures, layers and loops, on system energy performance, a dynamic exergy method is developed, improved, and applied to a complex oxy-combustion boiler island system for the first time. The three most common operating scenarios are studied, and the results show that the flow rate change process leads to less energy consumption than oxygen purity and air in-leakage change processes. The variation of oxygen purity produces the largest impact on system operation, and the operating parameter sensitivity is not affected by the presence of process control. The control system saves energy during flow rate and oxygen purity change processes, while it consumes energy during the air in-leakage change process. More attention should be paid to the oxygen purity change because it requires the largest control cost. In the control system, the supervisory control layer requires the greatest energy consumption and the largest control cost to maintain operating targets, while the steam control loops cause the main energy consumption.

The common engine concept for ALS application - A cost reduction approach

NASA Technical Reports Server (NTRS)

Bair, E. K.; Schindler, C. M.

1989-01-01

Future launch systems require the application of propulsion systems which have been designed and developed to meet mission model needs while providing high degrees of reliability and cost effectiveness. Vehicle configurations which utilize different propellant combinations for booster and core stages can benefit from a common engine approach where a single engine design can be configured to operate on either set of propellants and thus serve as either a booster or core engine. Engine design concepts and mission application for a vehicle employing a common engine are discussed. Engine program cost estimates were made and cost savings, over the design and development of two unique engines, estimated.

A new design to evaluate erosion and sediment control

Treesearch

Johnny M. Grace

2006-01-01

Water quality issues surrounding sediment movement related to forest operations are a focus in forest management. The forest road system is a primary area of concern related to sediment movement because roads are a component of most forest operations. Controlling sediment movement is a common objective in most forestry best management practices (BMPs). However, there...

USAF Aircraft Maintenance Officer Knowledge, Skills and Abilities and Commonalities among the Logistics Officer Corps

DTIC Science & Technology

2013-02-01

distribution managemen t operations to include managing cargo distribution functions such as receiving, inspecting, tracing, tracking, packaging, and...Production Management DE CDE ABCDEFG Scheduling DE ADEF ABCDEF T ie r 2 Flightline Operations E BDE Systems Engineering D ABDEG Table 19: 21R...logistics units/ elements and as members of general or executive s t affs in t he operating forces, supporting establishment, and joint staffs . They

Aeromedical Factors in Aviator Fatigue, Crew Work/Rest Schedules and Extended Flight Operations: An Annotated Bibliography.

DTIC Science & Technology

1981-01-01

complex is a common psychological reaction to stress, which causes a chronic overactivity of the higher brain centers and the vagal-parasympathetic...continuous military operations in which other complex man-machine systems were being used. In addition, we found great interest in multidisciplinary...2. Adams, J. T. 1967. Fatigue in helicopter aircrews in combat. In: Aeromedical aspects of helicopter operations in the tac- tical situation

An agent-oriented approach to automated mission operations

NASA Technical Reports Server (NTRS)

Truszkowski, Walt; Odubiyi, Jide

1994-01-01

As we plan for the next generation of Mission Operations Control Center (MOCC) systems, there are many opportunities for the increased utilization of innovative knowledge-based technologies. The innovative technology discussed is an advanced use of agent-oriented approaches to the automation of mission operations. The paper presents an overview of this technology and discusses applied operational scenarios currently being investigated and prototyped. A major focus of the current work is the development of a simple user mechanism that would empower operations staff members to create, in real time, software agents to assist them in common, labor intensive operations tasks. These operational tasks would include: handling routine data and information management functions; amplifying the capabilities of a spacecraft analyst/operator to rapidly identify, analyze, and correct spacecraft anomalies by correlating complex data/information sets and filtering error messages; improving routine monitoring and trend analysis by detecting common failure signatures; and serving as a sentinel for spacecraft changes during critical maneuvers enhancing the system's capabilities to support nonroutine operational conditions with minimum additional staff. An agent-based testbed is under development. This testbed will allow us to: (1) more clearly understand the intricacies of applying agent-based technology in support of the advanced automation of mission operations and (2) access the full set of benefits that can be realized by the proper application of agent-oriented technology in a mission operations environment. The testbed under development addresses some of the data management and report generation functions for the Explorer Platform (EP)/Extreme UltraViolet Explorer (EUVE) Flight Operations Team (FOT). We present an overview of agent-oriented technology and a detailed report on the operation's concept for the testbed.

Operability driven space system concept with high leverage technologies

NASA Astrophysics Data System (ADS)

Woo, Henry H.

1997-01-01

One of the common objectives of future launch and space transfer systems is to achieve low-cost and effective operational capability by automating processes from pre-launch to the end of mission. Hierarchical and integrated mission management, system management, autonomous GN&C, and integrated micro-nano avionics technologies are critical to extend or revitalize the exploitation of space. Essential to space transfer, orbital systems, Earth-To-Orbit (ETO), commercial and military aviation, and planetary systems are these high leverage hardware and software technologies. This paper covers the driving issues, goals, and requirements definition supported with typical concepts and utilization of multi-use technologies. The approach and method results in a practical system architecture and lower level design concepts.

Surgical PACS for the digital operating room. Systems engineering and specification of user requirements.

PubMed

Korb, Werner; Bohn, Stefan; Burgert, Oliver; Dietz, Andreas; Jacobs, Stephan; Falk, Volkmar; Meixensberger, Jürgen; Strauss, Gero; Trantakis, Christos; Lemke, Heinz U

2006-01-01

For better integration of surgical assist systems into the operating room, a common communication and processing plattform that is based on the users needs is needed. The development of such a system, a Surgical Picture Aquisition and Communication System (S-PACS), according the systems engineering cycle is oulined in this paper. The first two steps (concept and specification) for the engineering of the S-PACS are discussed.A method for the systematic integration of the users needs', the Quality Function Deployment (QFD), is presented. The properties of QFD for the underlying problem and first results are discussed. Finally, this leads to a first definition of an S-PACS system.

Ground System Harmonization Efforts at NASA's Goddard Space Flight Center

NASA Technical Reports Server (NTRS)

Smith, Dan

2011-01-01

This slide presentation reviews the efforts made at Goddard Space Flight Center in harmonizing the ground systems to assist in collaboration in space ventures. The key elements of this effort are: (1) Moving to a Common Framework (2) Use of Consultative Committee for Space Data Systems (CCSDS) Standards (3) Collaboration Across NASA Centers (4) Collaboration Across Industry and other Space Organizations. These efforts are working to bring into harmony the GSFC systems with CCSDS standards to allow for common software, use of Commercial Off the Shelf Software and low risk development and operations and also to work toward harmonization with other NASA centers

Common data buffer system. [communication with computational equipment utilized in spacecraft operations

NASA Technical Reports Server (NTRS)

Byrne, F. (Inventor)

1981-01-01

A high speed common data buffer system is described for providing an interface and communications medium between a plurality of computers utilized in a distributed computer complex forming part of a checkout, command and control system for space vehicles and associated ground support equipment. The system includes the capability for temporarily storing data to be transferred between computers, for transferring a plurality of interrupts between computers, for monitoring and recording these transfers, and for correcting errors incurred in these transfers. Validity checks are made on each transfer and appropriate error notification is given to the computer associated with that transfer.

Personal digital assistant-based, internet-enabled remote communication system for a wearable pneumatic biventricular assist device.

PubMed

Nam, Kyoung Won; Lee, Jung Joo; Hwang, Chang Mo; Choi, Seong Wook; Son, Ho Sung; Sun, Kyung

2007-11-01

Currently, personal mobile communication devices have become quite common, and the applications of such devices have expanded quickly. Remote communication systems might be employed for the telemonitoring of patients or the operating status of their medical devices. In this article, we describe the development of a mobile-based artificial heart telemanagement system for use in a wearable extracorporeal pneumatic biventricular assist device, which is capable of telemonitoring and telecontrolling the operating status of the ventricular assist device from any site. The system developed herein utilized small mobile phones for the client device and adopted a standard transmission control protocol/Internet protocol communication protocol for the purposes of telecommunication. The results of in vitro and animal experiments showed that the telemanagement system developed herein operated in accordance with the desired parameters.

SLAC modulator system improvements and reliability results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donaldson, A.R.

1998-06-01

In 1995, an improvement project was completed on the 244 klystron modulators in the linear accelerator. The modulator system has been previously described. This article offers project details and their resulting effect on modulator and component reliability. Prior to the project, the authors had collected four operating cycles (1991 through 1995) of MTTF data. In this discussion, the '91 data will be excluded since the modulators operated at 60 Hz. The five periods following the '91 run were reviewed due to the common repetition rate at 120 Hz.

Transforming to Effects-Based Operations: Lessons from the United Kingdom Experience

DTIC Science & Technology

2008-01-01

acquisition of the Airborne Stand-off Radar ( ASTOR ) ground surveillance system which links into the American Joint Surveillance and Attack Radar System...Pumas and the navy’s Sea King HC4s are very old and struggling to cope with the climates in which they are now operating. SECTION 4 The ongoing...Vol. 80, No. 1, pp. 49-62. 21. Tom King , House of Commons Parliamentary Debates, Statement on Defence “Options for Change,” July 25, 1990, session

Applications of Database Machines in Library Systems.

ERIC Educational Resources Information Center

Salmon, Stephen R.

1984-01-01

Characteristics and advantages of database machines are summarized and their applications to library functions are described. The ability to attach multiple hosts to the same database and flexibility in choosing operating and database management systems for different functions without loss of access to common database are noted. (EJS)

An Evaporative Cooling Model for Teaching Applied Psychrometrics

ERIC Educational Resources Information Center

Johnson, Donald M.

2004-01-01

Evaporative cooling systems are commonly used in controlled environment plant and animal production. These cooling systems operate based on well defined psychrometric principles. However, students often experience considerable difficulty in learning these principles when they are taught in an abstract, verbal manner. This article describes an…

Integrating Automation into a Multi-Mission Operations Center

NASA Technical Reports Server (NTRS)

Surka, Derek M.; Jones, Lori; Crouse, Patrick; Cary, Everett A, Jr.; Esposito, Timothy C.

2007-01-01

NASA Goddard Space Flight Center's Space Science Mission Operations (SSMO) Project is currently tackling the challenge of minimizing ground operations costs for multiple satellites that have surpassed their prime mission phase and are well into extended mission. These missions are being reengineered into a multi-mission operations center built around modern information technologies and a common ground system infrastructure. The effort began with the integration of four SMEX missions into a similar architecture that provides command and control capabilities and demonstrates fleet automation and control concepts as a pathfinder for additional mission integrations. The reengineered ground system, called the Multi-Mission Operations Center (MMOC), is now undergoing a transformation to support other SSMO missions, which include SOHO, Wind, and ACE. This paper presents the automation principles and lessons learned to date for integrating automation into an existing operations environment for multiple satellites.

Information Interaction Study for DER and DMS Interoperability

NASA Astrophysics Data System (ADS)

Liu, Haitao; Lu, Yiming; Lv, Guangxian; Liu, Peng; Chen, Yu; Zhang, Xinhui

The Common Information Model (CIM) is an abstract data model that can be used to represent the major objects in Distribution Management System (DMS) applications. Because the Common Information Model (CIM) doesn't modeling the Distributed Energy Resources (DERs), it can't meet the requirements of DER operation and management for Distribution Management System (DMS) advanced applications. Modeling of DER were studied based on a system point of view, the article initially proposed a CIM extended information model. By analysis the basic structure of the message interaction between DMS and DER, a bidirectional messaging mapping method based on data exchange was proposed.

Automated Ground Umbilical Systems (AGUS) Project

NASA Technical Reports Server (NTRS)

Gosselin, Armand M.

2007-01-01

All space vehicles require ground umbilical systems for servicing. Servicing requirements can include, but are not limited to, electrical power and control, propellant loading and venting, pneumatic system supply, hazard gas detection and purging as well as systems checkout capabilities. Of the various types of umbilicals, all require several common subsystems. These typically include an alignment system, mating and locking system, fluid connectors, electrical connectors and control !checkout systems. These systems have been designed to various levels of detail based on the needs for manual and/or automation requirements. The Automated Ground Umbilical Systems (AGUS) project is a multi-phase initiative to develop design performance requirements and concepts for launch system umbilicals. The automation aspect minimizes operational time and labor in ground umbilical processing while maintaining reliability. This current phase of the project reviews the design, development, testing and operations of ground umbilicals built for the Saturn, Shuttle, X-33 and Atlas V programs. Based on the design and operations lessons learned from these systems, umbilicals can be optimized for specific applications. The product of this study is a document containing details of existing systems and requirements for future automated umbilical systems with emphasis on design-for-operations (DFO).

Plugfest 2009: Global Interoperability in Telerobotics and Telemedicine

PubMed Central

King, H. Hawkeye; Hannaford, Blake; Kwok, Ka-Wai; Yang, Guang-Zhong; Griffiths, Paul; Okamura, Allison; Farkhatdinov, Ildar; Ryu, Jee-Hwan; Sankaranarayanan, Ganesh; Arikatla, Venkata; Tadano, Kotaro; Kawashima, Kenji; Peer, Angelika; Schauß, Thomas; Buss, Martin; Miller, Levi; Glozman, Daniel; Rosen, Jacob; Low, Thomas

2014-01-01

Despite the great diversity of teleoperator designs and applications, their underlying control systems have many similarities. These similarities can be exploited to enable inter-operability between heterogeneous systems. We have developed a network data specification, the Interoperable Telerobotics Protocol, that can be used for Internet based control of a wide range of teleoperators. In this work we test interoperable telerobotics on the global Internet, focusing on the telesurgery application domain. Fourteen globally dispersed telerobotic master and slave systems were connected in thirty trials in one twenty four hour period. Users performed common manipulation tasks to demonstrate effective master-slave operation. With twenty eight (93%) successful, unique connections the results show a high potential for standardizing telerobotic operation. Furthermore, new paradigms for telesurgical operation and training are presented, including a networked surgery trainer and upper-limb exoskeleton control of micro-manipulators. PMID:24748993

Biofiltration of Volatile Pollutants: Engineering Mechanisms for Improved Design, Long-term Operation, Prediction and Implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, Brian H.

1999-06-01

Biofiltration systems can be used for treatment of volatile organic compounds (VOCs); however, the systems are poorly understood and are currently operated as ''black boxes''. Common operational problems associated with biofilters include fouling, deactivation, and overgrowth, all of which make them ineffective for continuous, long-term use. The objective of this investigation is to develop generic methods for longterm stable operation, in particular by using selective limitation of supplemental nutrients while maintaining high activity. As part of this effort, we will provide deeper fundamental understanding of the important biological and transport mechanisms in biodestruction of sparingly soluble VOCs and extend thismore » approach and mathematical models to additional systems of high priority EM relevance--direct degradation and cometabolic degradation of priority pollutants such as BTEX and chlorinated organics.« less

BIOFILTRATION OF VOLATILE POLLUTANTS: Fundamental Mechanisms for Improved Design, Long-term Operation, Prediction, and Implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, Brian H.; Klasson, K. Thomas; Barton, John W.

2000-06-01

Biofiltration systems can be used for treatment of volatile organic compounds (VOCs); however, the systems are poorly understood and are currently operated as ''black boxes''. Common operational problems associated with biofilters include fouling, deactivation, and overgrowth, all of which make them ineffective for continuous, long-term use. The objective of this investigation is to develop generic methods for long-term stable operation, in particular by using selective limitation of supplemental nutrients while maintaining high activity. As part of this effort, we will provide deeper fundamental understanding of the important biological and transport mechanisms in biodestruction of sparingly soluble VOCs and extend thismore » approach and mathematical models to additional systems of high priority EM relevance--direct degradation and cometabolic degradation of priority pollutants such as BTEX and chlorinated organics.« less

29 CFR 779.219 - Unified operation may be achieved without common control or common ownership.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Unified operation may be achieved without common control or... Act May Apply; Enterprise Coverage Unified Operation Or Common Control § 779.219 Unified operation may be achieved without common control or common ownership. The performance of related activities through...

Demonstration of an Enhanced Vertical Magnetic Gradient System for UXO

DTIC Science & Technology

2008-12-01

fluxgate magnetometers , data recording console, laser altimeter, and acoustic altimeters were tested to ensure proper operation and performance. The VG...Simultaneous Electromagnetic Induction and Magnetometer System WAA wide area assessment ACKNOWLEDGEMENTS We wish to express our sincere...sensors. The benefits of vertical gradient (VG) configurations in magnetometer systems are common knowledge, and these configurations are routinely

A virtual reality environment for telescope operation

NASA Astrophysics Data System (ADS)

Martínez, Luis A.; Villarreal, José L.; Ángeles, Fernando; Bernal, Abel

2010-07-01

Astronomical observatories and telescopes are becoming increasingly large and complex systems, demanding to any potential user the acquirement of great amount of information previous to access them. At present, the most common way to overcome that information is through the implementation of larger graphical user interfaces and computer monitors to increase the display area. Tonantzintla Observatory has a 1-m telescope with a remote observing system. As a step forward in the improvement of the telescope software, we have designed a Virtual Reality (VR) environment that works as an extension of the remote system and allows us to operate the telescope. In this work we explore this alternative technology that is being suggested here as a software platform for the operation of the 1-m telescope.

Design and operations technologies - Integrating the pieces. [for future space systems design

NASA Technical Reports Server (NTRS)

Eldred, C. H.

1979-01-01

As major elements of life-cycle costs (LCC) having critical impacts on the initiation and utilization of future space programs, the areas of vehicle design and operations are reviewed in order to identify technology requirements. Common to both areas is the requirement for efficient integration of broad, complex systems. Operations technologies focus on the extension of space-based capabilities and cost reduction through the combination of innovative design, low-maintenance hardware, and increased manpower productivity. Design technologies focus on computer-aided techniques which increase productivity while maintaining a high degree of flexibility which enhances creativity and permits graceful design changes.

The Parable of the Boiled Safety Professional

NASA Technical Reports Server (NTRS)

Shivers, Charles H.

2011-01-01

Common and unique issues contribute to system failures. This paper touches on the concept of drift to failure as a cautionary message. Managers and leaders, design team members, fabricators and assemblers, analysis and assurance personnel, and others associated with operating and maintaining systems, need to pay attention to identify the manifestation of individual and collective behaviors that might indicate slips in rigor or focus or decisions that might eat away at safety margins as our system drifts to failure. Corrections to drift made during design and development phases may efficiently prevent or mitigate drift problems occurring in the operational phase.

47 CFR 22.959 - Rules governing processing of applications for initial systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Rules governing processing of applications for...) COMMON CARRIER SERVICES PUBLIC MOBILE SERVICES Cellular Radiotelephone Service § 22.959 Rules governing processing of applications for initial systems. Pending applications for authority to operate the first...

Updates to SCORPION persistent surveillance system with universal gateway

NASA Astrophysics Data System (ADS)

Coster, Michael; Chambers, Jon; Winters, Michael; Brunck, Al

2008-10-01

This paper addresses benefits derived from the universal gateway utilized in Northrop Grumman Systems Corporation's (NGSC) SCORPION, a persistent surveillance and target recognition system produced by the Xetron campus in Cincinnati, Ohio. SCORPION is currently deployed in Operations Iraqi Freedom (OIF) and Enduring Freedom (OEF). The SCORPION universal gateway is a flexible, field programmable system that provides integration of over forty Unattended Ground Sensor (UGS) types from a variety of manufacturers, multiple visible and thermal electro-optical (EO) imagers, and numerous long haul satellite and terrestrial communications links, including the Army Research Lab (ARL) Blue Radio. Xetron has been integrating best in class sensors with this universal gateway to provide encrypted data exfiltration to Common Operational Picture (COP) systems and remote sensor command and control since 1998. In addition to being fed to COP systems, SCORPION data can be visualized in the Common sensor Status (CStat) graphical user interface that allows for viewing and analysis of images and sensor data from up to seven hundred SCORPION system gateways on single or multiple displays. This user friendly visualization enables a large amount of sensor data and imagery to be used as actionable intelligence by a minimum number of analysts.

Power system restoration - A task force report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adibi, M.; Clelland, P.; Fink, L.

1986-01-01

The IEEE PES System Operation Subcommittee has established the Power System Restoration Task Force to: review operating practices, conduct a literature search, prepare relevant glossaries and bibliographies, and promote information exchange through technical papers. This is the first report of the Task Force. The problem of bulk power system restoration following a complete or partial collapse is practically as old as the electric utility industry itself. Many electric utilities have developed over the years system restoration schemes that meet the needs of their particular systems. These plans provide a great deal of insight into how the restorative process is viewedmore » by operating and planning personnel and what concerns and constraints any plan must operate under. The body of the report consists of notes prepared by members of the Task Force. It should not be interred that a complete reporting on Power System Restoration is undertaken here. The intent is to report upon work of the Task Force to date. The report also reviews several different restoration plans and shows their common concerns and constraints.« less

Agent-based paradigm for integration of interactive cable television operations and business support systems

NASA Astrophysics Data System (ADS)

Wattawa, Scott

1995-11-01

Offering interactive services and data in a hybrid fiber/coax cable system requires the coordination of a host of operations and business support systems. New service offerings and network growth and evolution create never-ending changes in the network infrastructure. Agent-based enterprise models provide a flexible mechanism for systems integration of service and support systems. Agent models also provide a mechanism to decouple interactive services from network architecture. By using the Java programming language, agents may be made safe, portable, and intelligent. This paper investigates the application of the Object Management Group's Common Object Request Brokering Architecture to the integration of a multiple services metropolitan area network.

Use of major surgery in south India: A retrospective audit of hospital claim data from a large, community health insurance program.

PubMed

Shaikh, Maaz; Woodward, Mark; Rahimi, Kazem; Patel, Anushka; Rath, Santosh; MacMahon, Stephen; Jha, Vivekanand

2015-05-01

Information on the use of major surgery in India is scarce. In this study we aimed to bridge this gap by auditing hospital claims from Rajiv Aarogyasri Community Health Insurance Scheme, which provides access to free hospital care through state-funded insurance to 68 million beneficiaries, an estimated 81% of population in the states of Telangana and Andhra Pradesh. Publicly available deidentified hospital claim data for all surgery procedures conducted between mid-2008 and mid-2012 were compiled across all 23 districts in Telangana and Andhra Pradesh. A total of 677,332 operative admissions (80% at private hospitals) were recorded at an annual rate of 259 per 100,000 beneficiaries, with male subjects accounting for 56% of admissions. Injury was the most common cause for operative admission (27%) with operative correction of long bone fractures being the most common procedure (20%) identified in the audit. Diseases of the digestive (16%), genitourinary (12%), and musculoskeletal (10%) systems were other leading causes for operative admissions. Most hospital bed-days were used by admissions for injuries (31%) and diseases of the digestive (17%) and musculoskeletal system (11%) costing 19%, 13%, and 11% of reimbursement. Operations on the circulatory system (8%) accounted for 21% of reimbursements. Annual per capita cost of operative claims was US$1.48. The use of surgery by an insured population in India continued to be low despite access to financing comparable with greater spending countries, highlighting need for strategies, beyond traditional health financing, that prioritize improvement in access, delivery, and use of operative care. Copyright © 2015 Elsevier Inc. All rights reserved.

ENVRIplus - European collaborative development of environmental infrastructures

NASA Astrophysics Data System (ADS)

Asmi, A.; Brus, M.; Kutsch, W. L.; Laj, P.

2016-12-01

European Research Infrastructures (RI) are built using ESFRI process, which dictates the steps towards a common European RIs. Building each RI separately creates unnessary barriers towards service users (e.g. on differing standards) and is not effiicient in e.g. e-science tool or data system development. To answer these inter-RI issues, the European Commission has funded several large scale cluster projectsto bring these RIs together already in planning and development phases to develop common tools, standards and methodologies, as well as learn from the exisiting systems. ENVRIplus is the cluster project for the environmental RIs in Europe, and provides platform for common development and sharing within the RI community. The project is organized around different themes, each having several workpackages with specific tasks. Major themesof the ENVRIplus are: Technical innovation, including tasks such as RI technology transfer, new observation techniques, autonomous operation, etc.; Data for science, with tasks such as RI reference model development, data discovery and citation, data publication, processing, etc.; Access to RIs, with specific tasks on interdicplinary and transnational access to RI services, and common access governance; Societal relevance and understanding, tackling on ethical issues on RI operations and understanding on human-environmental system and citizen science approaches, among others; Knowledge transfer, particularly between the RIs, and with developing RI organizations, organizing training and staff exchange; and Communication and dissemination, working towards a common environmental RI community (ENVRI community platform), and creating an own advisory RI discussion board (BEERi), and disseminating the ENVRIplus products globally. Importantly, all ENVRIplus results are open to any users from any country. Also, collaboration with international RIs and user communities are crucial to the success of the ENVRI initiatives. Overall goal is to do science globally, to answer global and regional critical challenges. The presentation will not only present the project, its state after nearly 2 years of operation, but will alsop present ideas towards building international and even more interdiciplinary collaboration on research infrastructures and their users.

A study of System Interface Sets (SIS) for the host, target and integration environments of the Space Station Program (SSP)

NASA Technical Reports Server (NTRS)

Mckay, Charles; Auty, David; Rogers, Kathy

1987-01-01

System interface sets (SIS) for large, complex, non-stop, distributed systems are examined. The SIS of the Space Station Program (SSP) was selected as the focus of this study because an appropriate virtual interface specification of the SIS is believed to have the most potential to free the project from four life cycle tyrannies which are rooted in a dependance on either a proprietary or particular instance of: operating systems, data management systems, communications systems, and instruction set architectures. The static perspective of the common Ada programming support environment interface set (CAIS) and the portable common execution environment (PCEE) activities are discussed. Also, the dynamic perspective of the PCEE is addressed.

2008 Federal Radionavigation Plan

DOT National Transportation Integrated Search

2009-01-01

The Federal Radionavigation Plan (FRP) is the official source of radionavigation policy and planning for the Federal Government. The FRP covers common-use, Federally operated radionavigation systems. This edition of the FRP combines the Federal Radio...

Occupational Health Screenings of the Virtual Warrior: Distributed Common Ground System Intelligence Operators Compared with Non-Combatant Support Personnel

DTIC Science & Technology

2014-02-01

long hours , shift work , relational conflict...reasons for an increase in medication. Such sleep problems were often explained in textual responses to be the result of long work hours , shift work ...to be operational in nature [1]. Specifically, long hours , shift work , organizational and leadership challenges, nature of work , additional

Reassessment of psychological distress and post-traumatic stress disorder in United States Air Force Distributed Common Ground System operators.

PubMed

Prince, Lillian; Chappelle, Wayne L; McDonald, Kent D; Goodman, Tanya; Cowper, Sara; Thompson, William

2015-03-01

The goal of this study was to assess for the main sources of occupational stress, as well as self-reported symptoms of distress and post-traumatic stress disorder among U.S. Air Force (USAF) Distributed Common Ground System (DCGS) intelligence exploitation and support personnel. DCGS intelligence operators (n=1091) and nonintelligence personnel (n = 447) assigned to a USAF Intelligence, Surveillance, and Reconnaissance Wing responded to the web-based survey. The overall survey response rate was 31%. Study results revealed the most problematic stressors among DCGS intelligence personnel included high workload, low manning, as well as organizational leadership and shift work issues. Results also revealed 14.35% of DCGS intelligence operators' self-reported high levels of psychological distress (twice the rate of DCGS nonintelligence support personnel). Furthermore, 2.0% to 2.5% self-reported high levels of post-traumatic stress disorder symptoms, with no significant difference between groups. The implications of these findings are discussed along with recommendations for USAF medical and mental health providers, as well as operational leadership. Reprint & Copyright © 2015 Association of Military Surgeons of the U.S.

AUTOMATIC COUNTING APPARATUS

DOEpatents

Howell, W.D.

1957-08-20

An apparatus for automatically recording the results of counting operations on trains of electrical pulses is described. The disadvantages of prior devices utilizing the two common methods of obtaining the count rate are overcome by this apparatus; in the case of time controlled operation, the disclosed system automatically records amy information stored by the scaler but not transferred to the printer at the end of the predetermined time controlled operations and, in the case of count controlled operation, provision is made to prevent a weak sample from occupying the apparatus for an excessively long period of time.

The Utilization of Network Enabled Capability in NATO Air C2 and Targeting Systems

DTIC Science & Technology

2013-06-01

TBMCS Mission Exchange 3.1 ICC-JCOP JCOP aims to provide a common operational picture to the NATO users to increase the situational awareness by...transformation steps (Figure 9). Figure 9: WISI consumed by Oracle’s SOA tools 3.4 ICC-ACCS- TBMCS Mission Exchange The aim of this experiment was to... TBMCS ) using a common methodology. For this purpose, initially, a common mission definition (CMD) was defined which had the same meaning for all of

Analysis of operating reserve demand curves in power system operations in the presence of variable generation

DOE PAGES

Krad, Ibrahim; Gao, David Wenzhong; Ela, Erik; ...

2017-06-07

The electric power industry landscape is continually evolving. As emerging technologies such as wind and solar generating systems become more cost effective, traditional power system operating strategies will need to be re-evaluated. The presence of wind and solar generation (commonly referred to as variable generation or VG) can increase variability and uncertainty in the net-load profile. One mechanism to mitigate this issue is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increased variability and uncertainty occurring at finer temporal resolutions. A newmore » operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this study, and its implications on power system operations are analyzed. Results show that flexibility reserve products can improve economic metrics, particularly in significantly reducing the number of scarcity pricing events, with minimal impacts on reliability metrics and production costs. Furthermore, the production costs increased due to increased VG curtailment - i.e. including the flexible ramping product in the commitment of excess thermal capacity that needed to remain online at the expense of VG output.« less

Analysis of operating reserve demand curves in power system operations in the presence of variable generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Gao, David Wenzhong; Ela, Erik

The electric power industry landscape is continually evolving. As emerging technologies such as wind and solar generating systems become more cost effective, traditional power system operating strategies will need to be re-evaluated. The presence of wind and solar generation (commonly referred to as variable generation or VG) can increase variability and uncertainty in the net-load profile. One mechanism to mitigate this issue is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increased variability and uncertainty occurring at finer temporal resolutions. A newmore » operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this study, and its implications on power system operations are analyzed. Results show that flexibility reserve products can improve economic metrics, particularly in significantly reducing the number of scarcity pricing events, with minimal impacts on reliability metrics and production costs. Furthermore, the production costs increased due to increased VG curtailment - i.e. including the flexible ramping product in the commitment of excess thermal capacity that needed to remain online at the expense of VG output.« less

Implementation of a Publish-Subscribe Protocol in Microgrid Islanding and Resynchronization with Self-Discovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Starke, M.; Herron, A.; King, D.

Communications systems and protocols are becoming second nature to utilities operating distribution systems. Traditionally, centralized communication approaches are often used, while recently in microgrid applications, distributed communication and control schema emerge offering several advantages such as improved system reliability, plug-and-play operation and distributed intelligence. Still, operation and control of microgrids including distributed communication schema have been less of a discussion in the literature. To address the challenge of multiple-inverter microgrid synchronization, a publish-subscribe protocol based, Data Distribution Service (DDS), communication schema for microgrids is proposed in this paper. The communication schema is discussed in details for individual devices such asmore » generators, photovoltaic systems, energy storage systems, microgrid point of common coupling switch, and supporting applications. In conclusion, islanding and resynchronization of a microgrid are demonstrated on a test-bed utilizing this schema.« less

Implementation of a Publish-Subscribe Protocol in Microgrid Islanding and Resynchronization with Self-Discovery

DOE PAGES

Starke, M.; Herron, A.; King, D.; ...

2017-08-24

Communications systems and protocols are becoming second nature to utilities operating distribution systems. Traditionally, centralized communication approaches are often used, while recently in microgrid applications, distributed communication and control schema emerge offering several advantages such as improved system reliability, plug-and-play operation and distributed intelligence. Still, operation and control of microgrids including distributed communication schema have been less of a discussion in the literature. To address the challenge of multiple-inverter microgrid synchronization, a publish-subscribe protocol based, Data Distribution Service (DDS), communication schema for microgrids is proposed in this paper. The communication schema is discussed in details for individual devices such asmore » generators, photovoltaic systems, energy storage systems, microgrid point of common coupling switch, and supporting applications. In conclusion, islanding and resynchronization of a microgrid are demonstrated on a test-bed utilizing this schema.« less

Oxygen Toxicity and Special Operations Forces Diving: Hidden and Dangerous

PubMed Central

Wingelaar, Thijs T.; van Ooij, Pieter-Jan A. M.; van Hulst, Rob A.

2017-01-01

In Special Operations Forces (SOF) closed-circuit rebreathers with 100% oxygen are commonly utilized for covert diving operations. Exposure to high partial pressures of oxygen (PO2) could cause damage to the central nervous system (CNS) and pulmonary system. Longer exposure time and higher PO2 leads to faster development of more serious pathology. Exposure to a PO2 above 1.4 ATA can cause CNS toxicity, leading to a wide range of neurologic complaints including convulsions. Pulmonary oxygen toxicity develops over time when exposed to a PO2 above 0.5 ATA and can lead to inflammation and fibrosis of lung tissue. Oxygen can also be toxic for the ocular system and may have systemic effects on the inflammatory system. Moreover, some of the effects of oxygen toxicity are irreversible. This paper describes the pathophysiology, epidemiology, signs and symptoms, risk factors and prediction models of oxygen toxicity, and their limitations on SOF diving. PMID:28790955

Global Positioning System Synchronized Active Light Autonomous Docking System

NASA Technical Reports Server (NTRS)

Howard, Richard T. (Inventor); Book, Michael L. (Inventor); Bryan, Thomas C. (Inventor); Bell, Joseph L. (Inventor)

1996-01-01

A Global Positioning System Synchronized Active Light Autonomous Docking System (GPSSALADS) for automatically docking a chase vehicle with a target vehicle comprising at least one active light emitting target which is operatively attached to the target vehicle. The target includes a three-dimensional array of concomitantly flashing lights which flash at a controlled common frequency. The GPSSALADS further comprises a visual tracking sensor operatively attached to the chase vehicle for detecting and tracking the target vehicle. Its performance is synchronized with the flash frequency of the lights by a synchronization means which is comprised of first and second internal clocks operatively connected to the active light target and visual tracking sensor, respectively, for providing timing control signals thereto, respectively. The synchronization means further includes first and second Global Positioning System receivers operatively connected to the first and second internal clocks, respectively, for repeatedly providing simultaneous synchronization pulses to the internal clocks, respectively. In addition, the GPSSALADS includes a docking process controller means which is operatively attached to the chase vehicle and is responsive to the visual tracking sensor for producing commands for the guidance and propulsion system of the chase vehicle.

Global Positioning System Synchronized Active Light Autonomous Docking System

NASA Technical Reports Server (NTRS)

Howard, Richard (Inventor)

1994-01-01

A Global Positioning System Synchronized Active Light Autonomous Docking System (GPSSALADS) for automatically docking a chase vehicle with a target vehicle comprises at least one active light emitting target which is operatively attached to the target vehicle. The target includes a three-dimensional array of concomitantly flashing lights which flash at a controlled common frequency. The GPSSALADS further comprises a visual tracking sensor operatively attached to the chase vehicle for detecting and tracking the target vehicle. Its performance is synchronized with the flash frequency of the lights by a synchronization means which is comprised of first and second internal clocks operatively connected to the active light target and visual tracking sensor, respectively, for providing timing control signals thereto, respectively. The synchronization means further includes first and second Global Positioning System receivers operatively connected to the first and second internal clocks, respectively, for repeatedly providing simultaneous synchronization pulses to the internal clocks, respectively. In addition, the GPSSALADS includes a docking process controller means which is operatively attached to the chase vehicle and is responsive to the visual tracking sensor for producing commands for the guidance and propulsion system of the chase vehicle.

Three-stage variability-based reserve modifiers for enhancing flexibility reserve requirements under high variable generation penetrations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Gao, David Wenzhong; Ibanez, Eduardo

2016-12-01

The electric power system has continuously evolved in order to accommodate new technologies and operating strategies. As the penetration of integrated variable generation in the system increases, it is beneficial to develop strategies that can help mitigate their effect on the grid. Historically, power system operators have held excess capacity during the commitment and dispatch process to allow the system to handle unforeseen load ramping events. As variable generation resources increase, sufficient flexibility scheduled in the system is required to ensure that system performance is not deteriorated in the presence of additional variability and uncertainty. This paper presents a systematicmore » comparison of various flexibility reserve strategies. Several of them are implemented and applied in a common test system, in order to evaluate their effect on the economic and reliable operations. Furthermore, a three stage reserve modifier algorithm is proposed and evaluated for its ability to improve system performance.« less

Operative experience of surgery residents: trends and challenges.

PubMed

Malangoni, Mark A; Biester, Thomas W; Jones, Andrew T; Klingensmith, Mary E; Lewis, Frank R

2013-01-01

To evaluate trends in operative experience and to determine the effect of establishing the Surgical Council on Resident Education (SCORE) operative classification system on changes in operative volume among graduating surgery residents. The general surgery operative logs of graduating surgery residents from 2005 were retrospectively compared with residents who completed training in 2010 and 2011. Nonparametric statistical analyses were used (Mann-Whitney and median test) with significance set at p<0.01. A total of 1022 residents completing residency in 2005 were compared with 1923 residents completing training in 2010-2011. Total operations reported increased from a median of 1023 to 1238 (21%) between 2005 and 2010-2011 (p<0.001). Cases increased in most SCORE categories. The median numbers of total, basic, and complex laparoscopic operations increased by 49%, 37%, and 82%, respectively, over the 5-year interval (p<0.001). Open cavitary (thoracic + abdominal) operations decreased by 5%, whereas other major operations increased by 35% (both p<0.001). The frequency of discrete operations done at least 10 times during residency did not change. The median number of SCORE essential-common operations performed ranged from 1 to 107, whereas essential-uncommon operations ranged from 0 to 4. Twenty-three of 67 SCORE essential-common operations (34%) had a median of less than 5 and 4 had a median of 0. The operative volume of graduating surgical residents has increased by 21% since 2005; however, the number of operations done 10 times or greater has not changed. Although open cavitary procedures continue to decline, there has been a large increase in endoscopy, complex laparoscopic, and other major operations. Some essential-common operations continue to be performed infrequently. These results suggest that education in the operating room must improve and alternate methods for teaching infrequently performed procedures are needed. © 2013 Published by Association of Program Directors in Surgery on behalf of Association of Program Directors in Surgery.

A home away from home. [life support system design for Space Station

NASA Technical Reports Server (NTRS)

Powell, L. E.; Hager, R. W.; Mccown, J. W.

1985-01-01

The role of the NASA-Marshall center in the development of the Space Station is discussed. The tasks of the center include the development of the life-support system; the design of the common module, which will form the basis for all pressurized Space Station modules; the design and outfit of a common module for the Material and Technology Laboratory (MTL) and logistics use; accommodations for operations of the Orbit Maneuvering Vehicle (OMV) and the Orbit Transfer Vehicle (OTV); and the Space Station propulsion system. A description of functions and design is given for each system, with particular emphasis on the goals of safety, efficiency, automation, and cost effectiveness.

ATLAS, an integrated structural analysis and design system. Volume 3: User's manual, input and execution data

NASA Technical Reports Server (NTRS)

Dreisbach, R. L. (Editor)

1979-01-01

The input data and execution control statements for the ATLAS integrated structural analysis and design system are described. It is operational on the Control Data Corporation (CDC) 6600/CYBER computers in a batch mode or in a time-shared mode via interactive graphic or text terminals. ATLAS is a modular system of computer codes with common executive and data base management components. The system provides an extensive set of general-purpose technical programs with analytical capabilities including stiffness, stress, loads, mass, substructuring, strength design, unsteady aerodynamics, vibration, and flutter analyses. The sequence and mode of execution of selected program modules are controlled via a common user-oriented language.

The 'INMARSAT' international maritime satellite communication system

NASA Astrophysics Data System (ADS)

Atserov, Iu. S.

1982-12-01

The history, design, operating characteristics, achievements, and prospects of INMARSAT are discussed. More than 1300 ships are presently equipped to operate within the system, and this number is expected to rise to about 5000 by 1986. The principle of operation involves single coordinating earth stations allocating telephone channels in their zones between other earth stations. The messages reach a common signalling channel with which all ship stations keep in touch. The ship stations are connected to the international telex network. The INMARSAT system enables ships in the automated mode of operation to establish telephone and telegraph comunication with any subscriber on the shore of any country. The quality of the communication is practically independent of the distance between ship and shore at any time of year and under any meteorological conditions. Estimates indicate that the use of satellite communication with ships reduces losses from accidents by 10 percent per year.

29 CFR 779.220 - Unified operation may exist as to separately owned or controlled activities which are related.

Code of Federal Regulations, 2010 CFR

2010-07-01

... otherwise, they are so performed as to constitute a unified business system organized for a common business... their activities in such manner as to be for all intents and purposes a single business system except..., in part or in whole, by the individual companies comprising the unified business system. The various...

Load Modeling and Calibration Techniques for Power System Studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chassin, Forrest S.; Mayhorn, Ebony T.; Elizondo, Marcelo A.

2011-09-23

Load modeling is the most uncertain area in power system simulations. Having an accurate load model is important for power system planning and operation. Here, a review of load modeling and calibration techniques is given. This paper is not comprehensive, but covers some of the techniques most commonly found in the literature. The advantages and disadvantages of each technique are outlined.

Regenerative switching CMOS system

DOEpatents

Welch, James D.

1998-01-01

Complementary Metal Oxide Semiconductor (CMOS) Schottky barrier Field Effect Transistor systems, which are a seriesed combination of N and P-Channel MOSFETS, in which Source Schottky barrier junctions of the N and P-Channel Schottky barrier MOSFETS are electically interconnected, (rather than the Drains as in conventional diffused junction CMOS), which Schottky barrier MOSFET system demonstrates Regenerative Inverting Switching Characteristics in use are disclosed. Both the N and P-Channel Schottky barrier MOSFET devices are unique in that they provide operational Drain Current vs. Drain to Source voltage as a function of Gate voltage only where the polarities of the Drain voltage and Gate voltage are opposite, referenced to the Source as a common terminal, and where the polarity of the voltage applied to the Gate is appropriate to cause Channel inversion. Experimentally derived results which demonstrate and verify the operation of N and P-Channel Schottky barrier MOSFETS actually fabricated on P and N-type Silicon respectively, by a common procedure using vacuum deposited Chromium as a Schottky barrier forming metal, are also provided.

Regenerative switching CMOS system

DOEpatents

Welch, J.D.

1998-06-02

Complementary Metal Oxide Semiconductor (CMOS) Schottky barrier Field Effect Transistor systems, which are a series combination of N and P-Channel MOSFETS, in which Source Schottky barrier junctions of the N and P-Channel Schottky barrier MOSFETS are electrically interconnected, (rather than the Drains as in conventional diffused junction CMOS), which Schottky barrier MOSFET system demonstrates Regenerative Inverting Switching Characteristics in use are disclosed. Both the N and P-Channel Schottky barrier MOSFET devices are unique in that they provide operational Drain Current vs. Drain to Source voltage as a function of Gate voltage only where the polarities of the Drain voltage and Gate voltage are opposite, referenced to the Source as a common terminal, and where the polarity of the voltage applied to the Gate is appropriate to cause Channel inversion. Experimentally derived results which demonstrate and verify the operation of N and P-Channel Schottky barrier MOSFETS actually fabricated on P and N-type Silicon respectively, by a common procedure using vacuum deposited Chromium as a Schottky barrier forming metal, are also provided. 14 figs.

Issues of Exploitation of Induction Motors in the Course of Underground Mining Operations

NASA Astrophysics Data System (ADS)

Gumula, Stanisław; Hudy, Wiktor; Piaskowska-Silarska, Malgorzata; Pytel, Krzysztof

2017-09-01

Mining industry is one of the most important customers of electric motors. The most commonly used in the contemporary mining industry is alternating current machines used for processing electrical energy into mechanical energy. The operating problems and the influence of qualitative interference acting on the inputs of individual regulators to field-oriented system in the course of underground mining operations has been presented in the publication. The object of controlling the speed is a slip-ring induction motor. Settings of regulators were calculated using an evolutionary algorithm. Examination of system dynamics was performed by a computer with the use of the MATLAB / Simulink software. According to analyzes, large distortion of input signals of regulators adversely affects the rotational speed that pursued by the control system, which may cause a large vibration of the whole system and, consequently, its much faster destruction. Designed system is characterized by a significantly better resistance to interference. The system is stable with the properly selected settings of regulators, which is particularly important during the operation of machinery used in underground mining.

Accelerating Malware Detection via a Graphics Processing Unit

DTIC Science & Technology

2010-09-01

Processing Unit . . . . . . . . . . . . . . . . . . 4 PE Portable Executable . . . . . . . . . . . . . . . . . . . . . 4 COFF Common Object File Format...operating systems for the future [Szo05]. The PE format is an updated version of the common object file format ( COFF ) [Mic06]. Microsoft released a new...NAs02]. These alerts can be costly in terms of time and resources for individuals and organizations to investigate each misidentified file [YWL07] [Vak10

Advanced Transport Operating System (ATOPS) color displays software description: MicroVAX system

NASA Technical Reports Server (NTRS)

Slominski, Christopher J.; Plyler, Valerie E.; Dickson, Richard W.

1992-01-01

This document describes the software created for the Display MicroVAX computer used for the Advanced Transport Operating Systems (ATOPS) project on the Transport Systems Research Vehicle (TSRV). The software delivery of February 27, 1991, known as the 'baseline display system', is the one described in this document. Throughout this publication, module descriptions are presented in a standardized format which contains module purpose, calling sequence, detailed description, and global references. The global references section includes subroutines, functions, and common variables referenced by a particular module. The system described supports the Research Flight Deck (RFD) of the TSRV. The RFD contains eight Cathode Ray Tubes (CRTs) which depict a Primary Flight Display, Navigation Display, System Warning Display, Takeoff Performance Monitoring System Display, and Engine Display.

47 CFR 32.1 - Background.

Code of Federal Regulations, 2010 CFR

2010-10-01

... financial accounting system which reports the results of operational and financial events in a manner which... permit upon the consistency of the well established body of accounting theories and principles commonly referred to as generally accepted accounting principles. ...

Evaluation of low-cost commercial-off-the-shelf autopilot systems for SUAS operations

NASA Astrophysics Data System (ADS)

Brown, Calvin Thomas

With this increase in unmanned aircraft system (UAS) operations, there is a need for a structured process to evaluate different commercially available systems, particularly autopilots. The Remotely Operated Aircraft Management, Interpretation, and Navigation from Ground or ROAMING scale was developed to meet this need. This scale is a modification of the widely accepted Handling Qualities Rating scale developed by George Cooper and Robert Harper Jr. The Cooper-Harper scale allows pilots to rate a vehicle's performance in completing some task. Similarly, the ROAMING scale allows UAS operators to evaluate the management and observability of UAS in completing some task. The standardized evaluative process consists of cost, size, weight, and power (SWAP) analysis, ease of implementation through procedural description of setup, ROAMING scale rating, a slightly modified NASA TLX rating, and comparison of manual operation to autonomous operation of the task. This standard for evaluation of autopilots and their software will lead to better understanding of the workload placed on UAS operators and indicate where improvements to design and operational procedures can be made. An assortment of low-cost commercial-off-the-shelf (COTS) autopilots were selected for use in the development of the evaluation and results of these tests demonstrate the commonalities and differences in these systems.

Anomalous azygos venous system in a south Indian cadaver: a case report

PubMed Central

2009-01-01

Introduction The posterior thoracic wall, an area drained by the azygos venous system, is a common site for surgical intervention. Since the venous part of the cardiovascular system is subject to most common variation, abnormalities in the azygos venous system are often reported. Case presentation During routine dissection classes for undergraduate medical students, we encountered a variation in the azygos venous system in a 65 years old south Indian male cadaver. We observed that there was no accessory azygos vein, and left 4th, 5th, 6th and 7th posterior intercostal veins terminated directly into azygos vein. Conclusion Identifying these types of variations is important during imaging this region and surgical operations of mediastinum. PMID:20181176

Metadata-Driven SOA-Based Application for Facilitation of Real-Time Data Warehousing

NASA Astrophysics Data System (ADS)

Pintar, Damir; Vranić, Mihaela; Skočir, Zoran

Service-oriented architecture (SOA) has already been widely recognized as an effective paradigm for achieving integration of diverse information systems. SOA-based applications can cross boundaries of platforms, operation systems and proprietary data standards, commonly through the usage of Web Services technology. On the other side, metadata is also commonly referred to as a potential integration tool given the fact that standardized metadata objects can provide useful information about specifics of unknown information systems with which one has interest in communicating with, using an approach commonly called "model-based integration". This paper presents the result of research regarding possible synergy between those two integration facilitators. This is accomplished with a vertical example of a metadata-driven SOA-based business process that provides ETL (Extraction, Transformation and Loading) and metadata services to a data warehousing system in need of a real-time ETL support.

Developing a Coalition Battle Management Language to Facilitate Interoperability Between Operation CIS, and Simulations in Support of Training and Mission Rehearsal

DTIC Science & Technology

2005-06-01

virtualisation of distributed computing and data resources such as processing, network bandwidth, and storage capacity, to create a single system...and Simulation (M&S) will be integrated into this heterogeneous SOA. M&S functionality will be available in the form of operational M&S services. One...documents defining net centric warfare, the use of M&S functionality is a common theme. Alberts and Hayes give a good overview on net centric operations

Electrochemical cell operation and system

DOEpatents

Maru, Hansraj C.

1980-03-11

Thermal control in fuel cell operation is affected through sensible heat of process gas by providing common input manifolding of the cell gas flow passage in communication with the cell electrolyte and an additional gas flow passage which is isolated from the cell electrolyte and in thermal communication with a heat-generating surface of the cell. Flow level in the cell gas flow passage is selected based on desired output electrical energy and flow level in the additional gas flow passage is selected in accordance with desired cell operating temperature.

Operating & Environmental Standards « Coast Guard Maritime Commons

Science.gov Websites

: Marine Safety Information Bulletin 03-18, Oily bilge water management This bulletin summarizes key legal updates to Marine Safety Center's ballast water management system website The Marine Safety Center recently updated two tools posted to its ballast water management system website to assist industry when

Spill-Detector-and-Shutoff Device

NASA Technical Reports Server (NTRS)

Jarvis, M. R.; Fulton, D. S.

1985-01-01

Overflow in liquid chromatography systems rapidly detected and stopped. Spill-detector-and-shutoff device incorporated into liquid-chromatography system. When liquid from output nozzle spills on liquid sensor, device automatically shuts off pump and releases solenoid to pinch off flow in tube. Device uses common type of alarm circuit reset manually before normal operation resumes.

Effects of semi-continous peracetic acid dosing on rainbow trout Oncorhynchus mykiss performance, water quality, and off-flavor compounds in recirculation aquaculture systems

USDA-ARS?s Scientific Manuscript database

Water clarifying and disinfection techniques such as ozonation and ultraviolet irradiation are commonly used in recirculation aquaculture systems (RAS); however, the capital and operating costs of these technologies are expensive. Cost-effective treatment options that maintain fish health and simult...

Beach Profile Analysis Systems (BPAS). Volume VI. BPAS User’s Guide: Analysis Module VOLCTR.

DTIC Science & Technology

1982-06-01

the two seawardmost points. Before computing volume changes, common bonds are established relative to the landward and seaward extent of the surveys on...bit word size, the FORTRAN- callable sort routine (interfacing with the NOS or NOSME operating system SORTMRG utility), and the utility subroutines and

The performance of integrated transconductance amplifiers as variable current sources for bio-electric impedance measurements.

PubMed

Smith, D N

1992-01-01

Multiple applied current impedance measurement systems require numbers of current sources which operate simultaneously at the same frequency and within the same phase but at variable amplitudes. Investigations into the performance of some integrated operational transconductance amplifiers as variable current sources are described. Measurements of breakthrough, non-linearity and common-mode output levels for LM13600, NE5517 and CA3280 were carried out. The effects of such errors on the overall performance and stability of multiple current systems when driving floating loads are considered.

A New Data Collection System for Ionospheric Modelling and Related Topics

DTIC Science & Technology

1993-04-15

Fluctuations of sgn, I strengt g d t1sr are cftcn os.;erved :,t utF frequencies in r ,:’i:- a t-e cayn r at r af’rer sunset. Marke d seasom c dependenc es in...Unfortunately there are few choices for real-time operating systems for PCs. The common alternate operating environments such as DeskView, MS Windows or...of the analog I/O and DMA support functions supplied by MetraByte. The processing module is where all the action is. After receiving a full data buffer

Systems Engineering in NASA's R&TD Programs

NASA Technical Reports Server (NTRS)

Jones, Harry

2005-01-01

Systems engineering is largely the analysis and planning that support the design, development, and operation of systems. The most common application of systems engineering is in guiding systems development projects that use a phased process of requirements, specifications, design, and development. This paper investigates how systems engineering techniques should be applied in research and technology development programs for advanced space systems. These programs should include anticipatory engineering of future space flight systems and a project portfolio selection process, as well as systems engineering for multiple development projects.

Patterns of technical error among surgical malpractice claims: an analysis of strategies to prevent injury to surgical patients.

PubMed

Regenbogen, Scott E; Greenberg, Caprice C; Studdert, David M; Lipsitz, Stuart R; Zinner, Michael J; Gawande, Atul A

2007-11-01

To identify the most prevalent patterns of technical errors in surgery, and evaluate commonly recommended interventions in light of these patterns. The majority of surgical adverse events involve technical errors, but little is known about the nature and causes of these events. We examined characteristics of technical errors and common contributing factors among closed surgical malpractice claims. Surgeon reviewers analyzed 444 randomly sampled surgical malpractice claims from four liability insurers. Among 258 claims in which injuries due to error were detected, 52% (n = 133) involved technical errors. These technical errors were further analyzed with a structured review instrument designed by qualitative content analysis. Forty-nine percent of the technical errors caused permanent disability; an additional 16% resulted in death. Two-thirds (65%) of the technical errors were linked to manual error, 9% to errors in judgment, and 26% to both manual and judgment error. A minority of technical errors involved advanced procedures requiring special training ("index operations"; 16%), surgeons inexperienced with the task (14%), or poorly supervised residents (9%). The majority involved experienced surgeons (73%), and occurred in routine, rather than index, operations (84%). Patient-related complexities-including emergencies, difficult or unexpected anatomy, and previous surgery-contributed to 61% of technical errors, and technology or systems failures contributed to 21%. Most technical errors occur in routine operations with experienced surgeons, under conditions of increased patient complexity or systems failure. Commonly recommended interventions, including restricting high-complexity operations to experienced surgeons, additional training for inexperienced surgeons, and stricter supervision of trainees, are likely to address only a minority of technical errors. Surgical safety research should instead focus on improving decision-making and performance in routine operations for complex patients and circumstances.

The Chimera II Real-Time Operating System for advanced sensor-based control applications

NASA Technical Reports Server (NTRS)

Stewart, David B.; Schmitz, Donald E.; Khosla, Pradeep K.

1992-01-01

Attention is given to the Chimera II Real-Time Operating System, which has been developed for advanced sensor-based control applications. The Chimera II provides a high-performance real-time kernel and a variety of IPC features. The hardware platform required to run Chimera II consists of commercially available hardware, and allows custom hardware to be easily integrated. The design allows it to be used with almost any type of VMEbus-based processors and devices. It allows radially differing hardware to be programmed using a common system, thus providing a first and necessary step towards the standardization of reconfigurable systems that results in a reduction of development time and cost.

Preserving Staffing Resources As a System: Nurses Leading Operations and Efficiency Initiatives.

PubMed

Hill, Karen S; Higdon, Karen; Porter, Bernard W; Rutland, Michael D; Vela, Donna K

2015-01-01

Nurse leaders have struggled for generations with using the right staff in appropriate roles and numbers to optimally cover patient care services and yet preserve salary dollars when possible. The Baptist Health system identified opportunities to enhance communication across facilities and encouraged executives and department leaders to work together to achieve common goals of efficiency and quality. Baptist Health created an operations and efficiency council with representation from each of the seven hospitals in the system, as well as corporate leaders and support staff. Beginning in April 2014, the system began consistently exceeding productivity targets and effectively eliminated a $30 million dollar salary variance from the spring of 2013.

Role of Pumped Storage Hydro Resources in Electricity Markets and System Operation: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ela, E.; Kirby, B.; Botterud, A.

2013-05-01

The most common form of utility- sized energy storage system is the pumped storage hydro system. Originally, these types of storage systems were economically viable simply because they displace more expensive generating units. However, over time, as those expensive units became more efficient and costs declined, pumped hydro storage units no longer have the operational edge. As a result, in the current electricity market environment, pumped storage hydro plants are struggling. To offset this phenomenon, certain market modifications should be addressed. This paper will introduce some of the challenges faced by pumped storage hydro plants in today's markets and purposemore » some solutions to those problems.« less

Assessments in the Global Peace Operations Initiative: A Systems Engineering Approach

DTIC Science & Technology

2014-06-01

police unit GCC GPOI Coordination Committee GIG GPOI Implementation Guide GPOI Global Peace Operations Initiative GRC GPOI Regional Committee G8...degree necessary to build a coherent assessments framework. The GPOI Implementation Guide ( GIG ) begins by alluding to what the program intended to...elements and associated interactions fully observed and understood. Using the U.S. economy as an example, Driscoll (2011) illustrates the common

Director, Operational Test and Evaluation FY 2014 Annual Report

DTIC Science & Technology

2015-01-01

Federal Departments and Agencies. Mitigation measures such as curtailment of wind turbine operations during test periods, identification of alternative...impact of wind turbines on ground-based and airborne radars, and this investment may help mitigate interference of wind turbines with test range...Frequency Active (SURTASS CLFA) Test Plan Tactical Unmanned Aircraft System Tactical Common Data Link (Shadow) FOT&E OTA Test Plan Tempest Wind 2014

Psychological Sciences Division 1979 Programs.

DTIC Science & Technology

1979-11-01

the potential for substantially improving the ONR effectiveness of Navy undersea manipulator sys- tems. Computer aided controls can be used to Report...OPERATOR VIEWING AND CONTROL OF the operator enters control orders) to determine UNDERSEA VEHICLE AND WORK SYS- ihe structure and mode of command inputs...efforts focus upon a class of control-display ele- Current Navy submersible work systems, such as ments common to general purpose undersea work CURV

Generalized Operations Simulation Environment for Aircraft Maintenance Training

DTIC Science & Technology

2004-04-01

Operations Simulation Environment ( GOSE ) project is a collaborative effort between AETC and AFRL to develop common, cost-effective, generalized VR training...maintenance training domain since it provided an opportunity to build on the VEST architecture. Development of GOSE involves re-engineering VEST as a scalable...modular, immersive VR training system comprised of PC-based hardware and software. GOSE initiatives include: (a) formalize training needs across

Commercial Space with Technology Maturation

NASA Technical Reports Server (NTRS)

McCleskey, Carey M.; Rhodes, Russell E.; Robinson, John W.

2013-01-01

To provide affordable space transportation we must be capable of using common fixed assets and the infrastructure for multiple purposes simultaneously. The Space Shuttle was operated for thirty years, but was not able to establish an effective continuous improvement program because of the high risk to the crew on every mission. An unmanned capability is needed to provide an acceptable risk to the primary mission. This paper is intended to present a case where a commercial space venture could share the large fixed cost of operating the infrastructure with the government while the government provides new advanced technology that is focused on reduced operating cost to the common launch transportation system. A conceivable commercial space venture could provide educational entertainment for the country's youth that would stimulate their interest in the science, technology, engineering, and mathematics (STEM) through access at entertainment parks or the existing Space Visitor Centers. The paper uses this example to demonstrate how growing public-private space market demand will re-orient space transportation industry priorities in flight and ground system design and technology development, and how the infrastructure is used and shared.

Video display terminal operation: a potential risk in the etiology and maintenance of temporomandibular disorders.

PubMed

Horowitz, L; Sarkin, J M

1992-01-01

Surveys indicate over 50 million Americans, mostly women, currently operate video display terminals (VDTs) at home or in the workplace. Recent epidemiological studies reveal more than 75% of approximately 30 million American temporomandibular disorder (TMD) sufferers are women. What does the VDT and TMD have in common besides an affinity for the female gender? TMD is associated with numerous risk factors that commonly initiate sympathetic nervous system and stress hormone response mechanisms resulting in muscle spasms, trigger point formation, and pain in the head and neck. Likewise VDT operation may be linked to three additional sympathetic nervous system irritants including: (1) electrostatic ambient air negative ion depletion, (2) electromagnetic radiation, and (3) eyestrain and postural stress associated with poor work habits and improper work station design. Additional research considering the roles these three factors may play in the etiology of TMD and other myofascial pain problems is indicated. Furthermore, dentists are advised to educate patients as to these possible risks, encourage preventive behaviors on the part of employers and employees, and recommend workplace health, safety, and ergonomic upgrades when indicated.

Ground Data System Risk Mitigation Techniques for Faster, Better, Cheaper Missions

NASA Technical Reports Server (NTRS)

Catena, John J.; Saylor, Rick; Casasanta, Ralph; Weikel, Craig; Powers, Edward I. (Technical Monitor)

2000-01-01

With the advent of faster, cheaper, and better missions, NASA Projects acknowledged that a higher level of risk was inherent and accepted with this approach. It was incumbent however upon each component of the Project whether spacecraft, payload, launch vehicle, or ground data system to ensure that the mission would nevertheless be an unqualified success. The Small Explorer (SMEX) program's ground data system (GDS) team developed risk mitigation techniques to achieve these goals starting in 1989. These techniques have evolved through the SMEX series of missions and are practiced today under the Triana program. These techniques are: (1) Mission Team Organization--empowerment of a closeknit ground data system team comprising system engineering, software engineering, testing, and flight operations personnel; (2) Common Spacecraft Test and Operational Control System--utilization of the pre-launch spacecraft integration system as the post-launch ground data system on-orbit command and control system; (3) Utilization of operations personnel in pre-launch testing--making the flight operations team an integrated member of the spacecraft testing activities at the beginning of the spacecraft fabrication phase; (4) Consolidated Test Team--combined system, mission readiness and operations testing to optimize test opportunities with the ground system and spacecraft; and (5). Reuse of Spacecraft, Systems and People--reuse of people, software and on-orbit spacecraft throughout the SMEX mission series. The SMEX ground system development approach for faster, cheaper, better missions has been very successful. This paper will discuss these risk management techniques in the areas of ground data system design, implementation, test, and operational readiness.

Common Technologies for Environmental Research Infrastructures in ENVRIplus

NASA Astrophysics Data System (ADS)

Paris, Jean-Daniel

2016-04-01

Environmental and geoscientific research infrastructures (RIs) are dedicated to distinct aspects of the ocean, atmosphere, ecosystems, or solid Earth research, yet there is significant commonality in the way they conceive, develop, operate and upgrade their observation systems and platforms. Many environmental Ris are distributed network of observatories (be it drifting buoys, geophysical observatories, ocean-bottom stations, atmospheric measurements sites) with needs for remote operations. Most RIs have to deal with calibration and standardization issues. RIs use a variety of measurements technologies, but this variety is based on a small, common set of physical principles. All RIs have set their own research and development priorities, and developed their solution to their problems - however many problems are common across RIs. Finally, RIs may overlap in terms of scientific perimeter. In ENVRIplus we aim, for the first time, to identify common opportunities for innovation, to support common research and development across RIs on promising issues, and more generally to create a forum to spread state of the art techniques among participants. ENVRIplus activities include 1) measurement technologies: where are the common types of measurement for which we can share expertise or common development? 2) Metrology : how do we tackle together the diversified challenge of quality assurance and standardization? 3) Remote operations: can we address collectively the need for autonomy, robustness and distributed data handling? And 4) joint operations for research: are we able to demonstrate that together, RIs are able to provide relevant information to support excellent research. In this process we need to nurture an ecosystem of key players. Can we involve all the key technologists of the European RIs for a greater mutual benefit? Can we pave the way to a growing common market for innovative European SMEs, with a common programmatic approach conducive to targeted R&D? Can we develop a common metrological language adapted to the observation of our environment? We aim at creating a space for exchange on the "hardware" issues of our networks of observatories, a forum that allows fast transmission across RIs of best practices and state of the art technology, a laboratory for joint research and co-development, where research infrastructures and their communities join efforts on well-identified objectives.

Common solutions for power, communication and robustness in operations of large measurement networks within Research Infrastructures

NASA Astrophysics Data System (ADS)

Huber, Robert; Beranzoli, Laura; Fiebig, Markus; Gilbert, Olivier; Laj, Paolo; Mazzola, Mauro; Paris, Jean-Daniel; Pedersen, Helle; Stocker, Markus; Vitale, Vito; Waldmann, Christoph

2017-04-01

European Environmental Research Infrastructures (RI) frequently comprise in situ observatories from large-scale networks of platforms or sites to local networks of various sensors. Network operation is usually a cumbersome aspect of these RIs facing specific technological problems related to operations in remote areas, maintenance of the network, transmission of observation values, etc.. Robust inter-connection within and across these networks is still at infancy level and the burden increases with remoteness of the station, harshness of environmental conditions, and unavailability of classic communication systems, which is a common feature here. Despite existing RIs having developed ad-hoc solutions to overcome specific problems and innovative technologies becoming available, no common approach yet exists. Within the European project ENVRIplus, a dedicated work package aims to stimulate common network operation technologies and approaches in terms of power supply and storage, robustness, and data transmission. Major objectives of this task are to review existing technologies and RI requirements, propose innovative solutions and evaluate the standardization potential prior to wider deployment across networks. Focus areas within these efforts are: improving energy production and storage units, testing robustness of RI equipment towards extreme conditions as well as methodologies for robust data transmission. We will introduce current project activities which are coordinated at various levels including the engineering as well as the data management perspective, and explain how environmental RIs can benefit from the developments.

Evaluation of the Trajectory Operations Applications Software Task (TOAST)

NASA Technical Reports Server (NTRS)

Perkins, Sharon; Martin, Andrea; Bavinger, Bill

1990-01-01

The Trajectory Operations Applications Software Task (TOAST) is a software development project under the auspices of the Mission Operations Directorate. Its purpose is to provide trajectory operation pre-mission and real-time support for the Space Shuttle program. As an Application Manager, TOAST provides an isolation layer between the underlying Unix operating system and the series of user programs. It provides two main services: a common interface to operating system functions with semantics appropriate for C or FORTRAN, and a structured input and output package that can be utilized by user application programs. In order to evaluate TOAST as an Application Manager, the task was to assess current and planned capabilities, compare capabilities to functions available in commercially-available off the shelf (COTS) and Flight Analysis Design System (FADS) users for TOAST implementation. As a result of the investigation, it was found that the current version of TOAST is well implemented and meets the needs of the real-time users. The plans for migrating TOAST to the X Window System are essentially sound; the Executive will port with minor changes, while Menu Handler will require a total rewrite. A series of recommendations for future TOAST directions are included.

Image-guided laparoscopic surgery in an open MRI operating theater.

PubMed

Tsutsumi, Norifumi; Tomikawa, Morimasa; Uemura, Munenori; Akahoshi, Tomohiko; Nagao, Yoshihiro; Konishi, Kozo; Ieiri, Satoshi; Hong, Jaesung; Maehara, Yoshihiko; Hashizume, Makoto

2013-06-01

The recent development of open magnetic resonance imaging (MRI) has provided an opportunity for the next stage of image-guided surgical and interventional procedures. The purpose of this study was to evaluate the feasibility of laparoscopic surgery under the pneumoperitoneum with the system of an open MRI operating theater. Five patients underwent laparoscopic surgery with a real-time augmented reality navigation system that we previously developed in a horizontal-type 0.4-T open MRI operating theater. All procedures were performed in an open MRI operating theater. During the operations, the laparoscopic monitor clearly showed the augmented reality models of the intraperitoneal structures, such as the common bile ducts and the urinary bladder, as well as the proper positions of the prosthesis. The navigation frame rate was 8 frames per min. The mean fiducial registration error was 6.88 ± 6.18 mm in navigated cases. We were able to use magnetic resonance-incompatible surgical instruments out of the 5-Gs restriction area, as well as conventional laparoscopic surgery, and we developed a real-time augmented reality navigation system using open MRI. Laparoscopic surgery with our real-time augmented reality navigation system in the open MRI operating theater is a feasible option.

Man-systems integration and the man-machine interface

NASA Technical Reports Server (NTRS)

Hale, Joseph P.

1990-01-01

Viewgraphs on man-systems integration and the man-machine interface are presented. Man-systems integration applies the systems' approach to the integration of the user and the machine to form an effective, symbiotic Man-Machine System (MMS). A MMS is a combination of one or more human beings and one or more physical components that are integrated through the common purpose of achieving some objective. The human operator interacts with the system through the Man-Machine Interface (MMI).

Gas-Liquid Flows and Phase Separation

NASA Technical Reports Server (NTRS)

McQuillen, John

2004-01-01

Common issues for space system designers include:Ability to Verify Performance in Normal Gravity prior to Deployment; System Stability; Phase Accumulation & Shedding; Phase Separation; Flow Distribution through Tees & Manifolds Boiling Crisis; Heat Transfer Coefficient; and Pressure Drop.The report concludes:Guidance similar to "A design that operates in a single phase is less complex than a design that has two-phase flow" is not always true considering the amount of effort spent on pressurizing, subcooling and phase separators to ensure single phase operation. While there is still much to learn about two-phase flow in reduced gravity, we have a good start. Focus now needs to be directed more towards system level problems .

NMESys: An expert system for network fault detection

NASA Technical Reports Server (NTRS)

Nelson, Peter C.; Warpinski, Janet

1991-01-01

The problem of network management is becoming an increasingly difficult and challenging task. It is very common today to find heterogeneous networks consisting of many different types of computers, operating systems, and protocols. The complexity of implementing a network with this many components is difficult enough, while the maintenance of such a network is an even larger problem. A prototype network management expert system, NMESys, implemented in the C Language Integrated Production System (CLIPS). NMESys concentrates on solving some of the critical problems encountered in managing a large network. The major goal of NMESys is to provide a network operator with an expert system tool to quickly and accurately detect hard failures, potential failures, and to minimize or eliminate user down time in a large network.

The MAP Autonomous Mission Control System

NASA Technical Reports Server (NTRS)

Breed, Juile; Coyle, Steven; Blahut, Kevin; Dent, Carolyn; Shendock, Robert; Rowe, Roger

2000-01-01

The Microwave Anisotropy Probe (MAP) mission is the second mission in NASA's Office of Space Science low-cost, Medium-class Explorers (MIDEX) program. The Explorers Program is designed to accomplish frequent, low cost, high quality space science investigations utilizing innovative, streamlined, efficient management, design and operations approaches. The MAP spacecraft will produce an accurate full-sky map of the cosmic microwave background temperature fluctuations with high sensitivity and angular resolution. The MAP spacecraft is planned for launch in early 2001, and will be staffed by only single-shift operations. During the rest of the time the spacecraft must be operated autonomously, with personnel available only on an on-call basis. Four (4) innovations will work cooperatively to enable a significant reduction in operations costs for the MAP spacecraft. First, the use of a common ground system for Spacecraft Integration and Test (I&T) as well as Operations. Second, the use of Finite State Modeling for intelligent autonomy. Third, the integration of a graphical planning engine to drive the autonomous systems without an intermediate manual step. And fourth, the ability for distributed operations via Web and pager access.

Phasing operator for two oscillators in classical field

NASA Technical Reports Server (NTRS)

Kim, Jong-Jean; Koo, Je-Hwan; Bae, Dong-Jae

1993-01-01

The origin of Dicke cooperative states was studied by considering two harmonic oscillators driven by a common field of radiation. The origin is assumed for superradiance in a system of molecules where no mutual interactions exist, but all of the molecules encounter the same field of radiation. A phasing operator as Phi(sub Nu) equals D(alpha) + P(sub Nu)D(alpha), where D(alpha) is the displacing operator and P(sub Nu) the projection operator for constant energy Nu for two oscillators, was derived. The eigenstates of the phasing operator Phi are found to show a finite correlation as in the Dicke cooperative states.

OR automation systems.

PubMed

2002-12-01

An operating room (OR) automation system is a combination of hardware and software designed to address efficiency issues in the OR by controling multiple devices via a common interface. Systems range from the relatively basic--allowing control of a few devices within a single OR--to advanced designs that are capable of not only controlling a wide range of devices within the OR but also exchanging information with remote locations.

Design of a Multi-mode Flight Deck Decision Support System for Airborne Conflict Management

NASA Technical Reports Server (NTRS)

Barhydt, Richard; Krishnamurthy, Karthik

2004-01-01

NASA Langley has developed a multi-mode decision support system for pilots operating in a Distributed Air-Ground Traffic Management (DAG-TM) environment. An Autonomous Operations Planner (AOP) assists pilots in performing separation assurance functions, including conflict detection, prevention, and resolution. Ongoing AOP design has been based on a comprehensive human factors analysis and evaluation results from previous human-in-the-loop experiments with airline pilot test subjects. AOP considers complex flight mode interactions and provides flight guidance to pilots consistent with the current aircraft control state. Pilots communicate goals to AOP by setting system preferences and actively probing potential trajectories for conflicts. To minimize training requirements and improve operational use, AOP design leverages existing alerting philosophies, displays, and crew interfaces common on commercial aircraft. Future work will consider trajectory prediction uncertainties, integration with the TCAS collision avoidance system, and will incorporate enhancements based on an upcoming air-ground coordination experiment.

A microcomputer controlled snow ski binding system--I. Instrumentation and field evaluation.

PubMed

MacGregor, D; Hull, M L; Dorius, L K

1985-01-01

This paper presents the design and field evaluation of the first microcomputer controlled ski binding system. This system incorporates an Intel 8086 microcomputer controller and an integral binding/dynamometer. This instrumentation system not only undertakes real time control, but also it records dynamometer data via a miniature digital cassette tape recorder. The integral binding/dynamometer offers the same operational and mounting convenience of commercially available mechanical bindings. The binding may be released either manually or electrically via the controller. Comprised of four octagonal half strain rings, the strain gage dynamometer measures the three moment load components at the boot. To enable the user to conveniently operate the computer, extensive operating software was developed. The operating software is discussed in relation to both the acquisition and storage of data from the dynamometer and the control of the electro-mechanical snow ski binding. The binding system has been used successfully to both record boot moment components and control ski binding release during actual skiing maneuvers. Moment histories typical of three common recreational skiing maneuvers are presented.

In-Space Cryogenic Propellant Depot (ISCPD) Architecture Definitions and Systems Studies

NASA Technical Reports Server (NTRS)

Fikes, John C.; Howell, Joe T.; Henley, Mark

2006-01-01

The objectives of the ISCPD Architecture Definitions and Systems Studies were to determine high leverage propellant depot architecture concepts, system configuration trades, and related technologies to enable more ambitious and affordable human and robotic exploration of the Earth Neighborhood and beyond. This activity identified architectures and concepts that preposition and store propellants in space for exploration and commercial space activities, consistent with Exploration Systems Research and Technology (ESR&T) objectives. Commonalities across mission scenarios for these architecture definitions, depot concepts, technologies, and operations were identified that also best satisfy the Vision of Space Exploration. Trade studies were conducted, technology development needs identified and assessments performed to drive out the roadmap for obtaining an in-space cryogenic propellant depot capability. The Boeing Company supported the NASA Marshall Space Flight Center (MSFC) by conducting this Depot System Architecture Development Study. The primary objectives of this depot architecture study were: (1) determine high leverage propellant depot concepts and related technologies; (2) identify commonalities across mission scenarios of depot concepts, technologies, and operations; (3) determine the best depot concepts and key technology requirements and (4) identify technology development needs including definition of ground and space test article requirements.

[Research on infrared safety protection system for machine tool].

PubMed

Zhang, Shuan-Ji; Zhang, Zhi-Ling; Yan, Hui-Ying; Wang, Song-De

2008-04-01

In order to ensure personal safety and prevent injury accident in machine tool operation, an infrared machine tool safety system was designed with infrared transmitting-receiving module, memory self-locked relay and voice recording-playing module. When the operator does not enter the danger area, the system has no response. Once the operator's whole or part of body enters the danger area and shades the infrared beam, the system will alarm and output an control signal to the machine tool executive element, and at the same time, the system makes the machine tool emergency stop to prevent equipment damaged and person injured. The system has a module framework, and has many advantages including safety, reliability, common use, circuit simplicity, maintenance convenience, low power consumption, low costs, working stability, easy debugging, vibration resistance and interference resistance. It is suitable for being installed and used in different machine tools such as punch machine, pour plastic machine, digital control machine, armor plate cutting machine, pipe bending machine, oil pressure machine etc.

Low-Cost SIRTF Flight Operations

NASA Astrophysics Data System (ADS)

Deutsch, M.-J.; Ebersole, M.; Nichols, J.

1997-12-01

The Space Infrared Telescope Facility (SIRTF) , the fourth of the Great Observatories, will be placed in a unique solar orbit trailing the Earth, in 2001. SIRTF will acquire both imaging and spectral data using large infrared detector arrays from 3.5mm to 160mm. The primary science objectives are (1) search for and study of brown dwarfs and super planets, (2) discovery and study of protoplanetary debris disks, (3) study of ultraluminous galaxies and active galactic nuclei, and (4) study of the early Universe. Driven by the limited cryogenic lifetime of 2.5 years, with a goal of 5 years, and the severely cost-capped development, a Mission Planning and Operations system is being designed that will result in high on-board efficiency (>90%) and low-cost operation, yet will accommodate rapid response science requirements . SIRTF is designing an architecture for an operations system that will be shared between science and flight operations. Crucial to this effort is the philosophy of an integrated science and engineering plan, co-location, cross-training of teams and common planning tools. The common tool set will enable the automatic generation of an integrated and conflict free planned schedule accommodating 20 000 observations and engineering activities a year. The shared tool set will help generate standard observations , (sometimes non-standard) engineering activities and manage the ground and flight resources and constraints appropriately. The ground software will allow the development from the ground of robust event driven sequences. Flexibility will be provided to incorporate newly discovered science opportunities or health issues late in the process and via quick links. This shared science and flight operations process if used from observation selection through sequence and command generation, will provide a low-cost operations system. Though SIRTF is a 'Great Observatory', its annual mission operations costs will more closely resemble those of an Explorer class mission.

Health systems strengthening: a common classification and framework for investment analysis

PubMed Central

Shakarishvili, George; Lansang, Mary Ann; Mitta, Vinod; Bornemisza, Olga; Blakley, Matthew; Kley, Nicole; Burgess, Craig; Atun, Rifat

2011-01-01

Significant scale-up of donors’ investments in health systems strengthening (HSS), and the increased application of harmonization mechanisms for jointly channelling donor resources in countries, necessitate the development of a common framework for tracking donors’ HSS expenditures. Such a framework would make it possible to comparatively analyse donors’ contributions to strengthening specific aspects of countries’ health systems in multi-donor-supported HSS environments. Four pre-requisite factors are required for developing such a framework: (i) harmonization of conceptual and operational understanding of what constitutes HSS; (ii) development of a common set of criteria to define health expenditures as contributors to HSS; (iii) development of a common HSS classification system; and (iv) harmonization of HSS programmatic and financial data to allow for inter-agency comparative analyses. Building on the analysis of these aspects, the paper proposes a framework for tracking donors’ investments in HSS, as a departure point for further discussions aimed at developing a commonly agreed approach. Comparative analysis of financial allocations by the Global Fund to Fight AIDS, Tuberculosis and Malaria and the GAVI Alliance for HSS, as an illustrative example of applying the proposed framework in practice, is also presented. PMID:20952397

Next Generation Community Based Unified Global Modeling System Development and Operational Implementation Strategies at NCEP

NASA Astrophysics Data System (ADS)

Tallapragada, V.

2017-12-01

NOAA's Next Generation Global Prediction System (NGGPS) has provided the unique opportunity to develop and implement a non-hydrostatic global model based on Geophysical Fluid Dynamics Laboratory (GFDL) Finite Volume Cubed Sphere (FV3) Dynamic Core at National Centers for Environmental Prediction (NCEP), making a leap-step advancement in seamless prediction capabilities across all spatial and temporal scales. Model development efforts are centralized with unified model development in the NOAA Environmental Modeling System (NEMS) infrastructure based on Earth System Modeling Framework (ESMF). A more sophisticated coupling among various earth system components is being enabled within NEMS following National Unified Operational Prediction Capability (NUOPC) standards. The eventual goal of unifying global and regional models will enable operational global models operating at convective resolving scales. Apart from the advanced non-hydrostatic dynamic core and coupling to various earth system components, advanced physics and data assimilation techniques are essential for improved forecast skill. NGGPS is spearheading ambitious physics and data assimilation strategies, concentrating on creation of a Common Community Physics Package (CCPP) and Joint Effort for Data Assimilation Integration (JEDI). Both initiatives are expected to be community developed, with emphasis on research transitioning to operations (R2O). The unified modeling system is being built to support the needs of both operations and research. Different layers of community partners are also established with specific roles/responsibilities for researchers, core development partners, trusted super-users, and operations. Stakeholders are engaged at all stages to help drive the direction of development, resources allocations and prioritization. This talk presents the current and future plans of unified model development at NCEP for weather, sub-seasonal, and seasonal climate prediction applications with special emphasis on implementation of NCEP FV3 Global Forecast System (GFS) and Global Ensemble Forecast System (GEFS) into operations by 2019.

Video Guidance Sensor for Surface Mobility Operations

NASA Technical Reports Server (NTRS)

Fernandez, Kenneth R.; Fischer, Richard; Bryan, Thomas; Howell, Joe; Howard, Ricky; Peters, Bruce

2008-01-01

Robotic systems and surface mobility will play an increased role in future exploration missions. Unlike the LRV during Apollo era which was an astronaut piloted vehicle future systems will include teleoperated and semi-autonomous operations. The tasks given to these vehicles will run the range from infrastructure maintenance, ISRU, and construction to name a few. A common task that may be performed would be the retrieval and deployment of trailer mounted equipment. Operational scenarios may require these operations to be performed remotely via a teleoperated mode,or semi-autonomously. This presentation describes the on-going project to adapt the Automated Rendezvous and Capture (AR&C) sensor developed at the Marshall Space Flight Center for use in an automated trailer pick-up and deployment operation. The sensor which has been successfully demonstrated on-orbit has been mounted on an iRobot/John Deere RGATOR autonomous vehicle for this demonstration which will be completed in the March 2008 time-frame.

Combined rankine and vapor compression cycles

DOEpatents

Radcliff, Thomas D.; Biederman, Bruce P.; Brasz, Joost J.

2005-04-19

An organic rankine cycle system is combined with a vapor compression cycle system with the turbine generator of the organic rankine cycle generating the power necessary to operate the motor of the refrigerant compressor. The vapor compression cycle is applied with its evaporator cooling the inlet air into a gas turbine, and the organic rankine cycle is applied to receive heat from a gas turbine exhaust to heat its boiler within one embodiment, a common condenser is used for the organic rankine cycle and the vapor compression cycle, with a common refrigerant, R-245a being circulated within both systems. In another embodiment, the turbine driven generator has a common shaft connected to the compressor to thereby eliminate the need for a separate motor to drive the compressor. In another embodiment, an organic rankine cycle system is applied to an internal combustion engine to cool the fluids thereof, and the turbo charged air is cooled first by the organic rankine cycle system and then by an air conditioner prior to passing into the intake of the engine.

Exhaustive Thresholds and Resistance Checkpoints

NASA Technical Reports Server (NTRS)

Easton, Charles; Khuzadi, Mbuyi

2008-01-01

Once deployed, all intricate systems that operate for a long time (such as an airplane or chemical processing plant) experience degraded performance during operational lifetime. These can result from losses of integrity in subsystems and parts that generally do not materially impact the operation of the vehicle (e.g., the light behind the button that opens the sliding door of the minivan). Or it can result from loss of more critical parts or subsystems. Such losses need to be handled quickly in order to avoid loss of personnel, mission, or part of the system itself. In order to manage degraded systems, knowledge of its potential problem areas and the means by which these problems are detected should be developed during the initial development of the system. Once determined, a web of sensors is employed and their outputs are monitored with other system parameters while the system is in preparation or operation. Just gathering the data is only part of the story. The interpretation of the data itself and the response of the system must be carefully developed as well to avoid a mishap. Typically, systems use a test-threshold-response paradigm to process potential system faults. However, such processing sub-systems can suffer from errors and oversights of a consistent type, causing system aberrant behavior instead of expected system and recovery operations. In our study, we developed a complete checklist for determining the completeness of a fault system and its robustness to common processing and response difficulties.

Design of a steganographic virtual operating system

NASA Astrophysics Data System (ADS)

Ashendorf, Elan; Craver, Scott

2015-03-01

A steganographic file system is a secure file system whose very existence on a disk is concealed. Customarily, these systems hide an encrypted volume within unused disk blocks, slack space, or atop conventional encrypted volumes. These file systems are far from undetectable, however: aside from their ciphertext footprint, they require a software or driver installation whose presence can attract attention and then targeted surveillance. We describe a new steganographic operating environment that requires no visible software installation, launching instead from a concealed bootstrap program that can be extracted and invoked with a chain of common Unix commands. Our system conceals its payload within innocuous files that typically contain high-entropy data, producing a footprint that is far less conspicuous than existing methods. The system uses a local web server to provide a file system, user interface and applications through a web architecture.

A data seamless interaction scheme between electric power secondary business systems

NASA Astrophysics Data System (ADS)

Ai, Wenkai; Qian, Feng

2018-03-01

At present, the data interaction of electric power secondary business systems is very high, and it is not universal to develop programs when data interaction is carried out by different manufacturers' electric power secondary business systems. There are different interaction schemes for electric power secondary business systems with different manufacturers, which lead to high development cost, low reusability and high maintenance difficulty. This paper introduces a new data seamless interaction scheme between electric power secondary business systems. The scheme adopts the international common Java message service protocol as the transmission protocol, adopts the common JavaScript object symbol format as the data interactive format, unified electric power secondary business systems data interactive way, improve reusability, reduce complexity, monitor the operation of the electric power secondary business systems construction has laid a solid foundation.

Designing berthing mechanisms for international compatibility

NASA Technical Reports Server (NTRS)

Winch, John; Gonzalez-Vallejo, Juan J.

1991-01-01

The paper examines the technological issues regarding common berthing interfaces for the Space Station Freedom and pressurized modules from U.S., European, and Japanese space programs. The development of the common berthing mechanism (CBM) is based on common requirements concerning specifications, launch environments, and the unique requirements of ESA's Man-Tended Free Flyer. The berthing mechanism is composed of an active and a passive half, a remote manipulator system, 4 capture-latch assemblies, 16 structural bolts, and a pressure gage to verify equalization. Extensive graphic and verbal descriptions of each element are presented emphasizing the capture-latch motion and powered-bolt operation. The support systems to complete the interface are listed, and the manufacturing requirements for consistent fabrication are discussed to ensure effective international development.

Sharing from Scratch: How To Network CD-ROM.

ERIC Educational Resources Information Center

Doering, David

1998-01-01

Examines common CD-ROM networking architectures: via existing operating systems (OS), thin server towers, and dedicated servers. Discusses digital video disc (DVD) and non-CD/DVD optical storage solutions and presents case studies of networks that work. (PEN)

USAF/WL robust 300 C wire insulation system program status

NASA Technical Reports Server (NTRS)

Wong, Wing

1995-01-01

The objective of this program is to identify, develop, and demonstrate an optimum wire insulation system capable of continuous operation at 300 C which possesses a combination of superior electrical (AC or DC), mechanical, and physical properties over Kapton derived insulations described in MIL-W-81381 and those hybrid materials commonly known as TKT constructions.

Airborne multispectral data collection

NASA Technical Reports Server (NTRS)

Hasell, P. G., Jr.

1974-01-01

Multispectral mapping accomplishments using the M7 airborne scanner are summarized. The M7 system is described and overall results of specific data collection flight operations since June 1971 are reviewed. A major advantage of the M7 system is that all spectral bands of the scanner are in common spatial registration, whereas in the M5 they were not.

USAF/WL robust 300 C wire insulation system program status

NASA Astrophysics Data System (ADS)

Wong, Wing

1995-11-01

The objective of this program is to identify, develop, and demonstrate an optimum wire insulation system capable of continuous operation at 300 C which possesses a combination of superior electrical (AC or DC), mechanical, and physical properties over Kapton derived insulations described in MIL-W-81381 and those hybrid materials commonly known as TKT constructions.

Adaptable state based control system

NASA Technical Reports Server (NTRS)

Rasmussen, Robert D. (Inventor); Dvorak, Daniel L. (Inventor); Gostelow, Kim P. (Inventor); Starbird, Thomas W. (Inventor); Gat, Erann (Inventor); Chien, Steve Ankuo (Inventor); Keller, Robert M. (Inventor)

2004-01-01

An autonomous controller, comprised of a state knowledge manager, a control executor, hardware proxies and a statistical estimator collaborates with a goal elaborator, with which it shares common models of the behavior of the system and the controller. The elaborator uses the common models to generate from temporally indeterminate sets of goals, executable goals to be executed by the controller. The controller may be updated to operate in a different system or environment than that for which it was originally designed by the replacement of shared statistical models and by the instantiation of a new set of state variable objects derived from a state variable class. The adaptation of the controller does not require substantial modification of the goal elaborator for its application to the new system or environment.

A study of the selection of microcomputer architectures to automate planetary spacecraft power systems

NASA Technical Reports Server (NTRS)

Nauda, A.

1982-01-01

Performance and reliability models of alternate microcomputer architectures as a methodology for optimizing system design were examined. A methodology for selecting an optimum microcomputer architecture for autonomous operation of planetary spacecraft power systems was developed. Various microcomputer system architectures are analyzed to determine their application to spacecraft power systems. It is suggested that no standardization formula or common set of guidelines exists which provides an optimum configuration for a given set of specifications.

Ship Integration of Energy Scavenging Technology for Sea Base Operations

DTIC Science & Technology

2009-07-01

operates similar to the common commercial refrigerating system in reverse like a heat pump.3 However, cold water pipes do pose a 12 Naval Surface...sunlight at the focal point in a solar collector , more light can be converted to electricity for less solar cell material. Solar concentrators come in...Kotter, D.K., et al. (2008). Proceeding from ES2008: Solar Nantenna Electromagnetic Collectors . Jacksonville, Florida: Energy Sustainability 2008

Analysis of Operating Principles with S-system Models

PubMed Central

Lee, Yun; Chen, Po-Wei; Voit, Eberhard O.

2011-01-01

Operating principles address general questions regarding the response dynamics of biological systems as we observe or hypothesize them, in comparison to a priori equally valid alternatives. In analogy to design principles, the question arises: Why are some operating strategies encountered more frequently than others and in what sense might they be superior? It is at this point impossible to study operation principles in complete generality, but the work here discusses the important situation where a biological system must shift operation from its normal steady state to a new steady state. This situation is quite common and includes many stress responses. We present two distinct methods for determining different solutions to this task of achieving a new target steady state. Both methods utilize the property of S-system models within Biochemical Systems Theory (BST) that steady-states can be explicitly represented as systems of linear algebraic equations. The first method uses matrix inversion, a pseudo-inverse, or regression to characterize the entire admissible solution space. Operations on the basis of the solution space permit modest alterations of the transients toward the target steady state. The second method uses standard or mixed integer linear programming to determine admissible solutions that satisfy criteria of functional effectiveness, which are specified beforehand. As an illustration, we use both methods to characterize alternative response patterns of yeast subjected to heat stress, and compare them with observations from the literature. PMID:21377479

Alternative Method to Simulate a Sub-idle Engine Operation in Order to Synthesize Its Control System

NASA Astrophysics Data System (ADS)

Sukhovii, Sergii I.; Sirenko, Feliks F.; Yepifanov, Sergiy V.; Loboda, Igor

2016-09-01

The steady-state and transient engine performances in control systems are usually evaluated by applying thermodynamic engine models. Most models operate between the idle and maximum power points, only recently, they sometimes address a sub-idle operating range. The lack of information about the component maps at the sub-idle modes presents a challenging problem. A common method to cope with the problem is to extrapolate the component performances to the sub-idle range. Precise extrapolation is also a challenge. As a rule, many scientists concern only particular aspects of the problem such as the lighting combustion chamber or the turbine operation under the turned-off conditions of the combustion chamber. However, there are no reports about a model that considers all of these aspects and simulates the engine starting. The proposed paper addresses a new method to simulate the starting. The method substitutes the non-linear thermodynamic model with a linear dynamic model, which is supplemented with a simplified static model. The latter model is the set of direct relations between parameters that are used in the control algorithms instead of commonly used component performances. Specifically, this model consists of simplified relations between the gas path parameters and the corrected rotational speed.

The virtual digital nuclear power plant: A modern tool for supporting the lifecycle of VVER-based nuclear power units

NASA Astrophysics Data System (ADS)

Arkadov, G. V.; Zhukavin, A. P.; Kroshilin, A. E.; Parshikov, I. A.; Solov'ev, S. L.; Shishov, A. V.

2014-10-01

The article describes the "Virtual Digital VVER-Based Nuclear Power Plant" computerized system comprising a totality of verified initial data (sets of input data for a model intended for describing the behavior of nuclear power plant (NPP) systems in design and emergency modes of their operation) and a unified system of new-generation computation codes intended for carrying out coordinated computation of the variety of physical processes in the reactor core and NPP equipment. Experiments with the demonstration version of the "Virtual Digital VVER-Based NPP" computerized system has shown that it is in principle possible to set up a unified system of computation codes in a common software environment for carrying out interconnected calculations of various physical phenomena at NPPs constructed according to the standard AES-2006 project. With the full-scale version of the "Virtual Digital VVER-Based NPP" computerized system put in operation, the concerned engineering, design, construction, and operating organizations will have access to all necessary information relating to the NPP power unit project throughout its entire lifecycle. The domestically developed commercial-grade software product set to operate as an independently operating application to the project will bring about additional competitive advantages in the modern market of nuclear power technologies.

A Novel Hybrid Clonal Selection Algorithm with Combinatorial Recombination and Modified Hypermutation Operators for Global Optimization

PubMed Central

Lin, Jingjing; Jing, Honglei

2016-01-01

Artificial immune system is one of the most recently introduced intelligence methods which was inspired by biological immune system. Most immune system inspired algorithms are based on the clonal selection principle, known as clonal selection algorithms (CSAs). When coping with complex optimization problems with the characteristics of multimodality, high dimension, rotation, and composition, the traditional CSAs often suffer from the premature convergence and unsatisfied accuracy. To address these concerning issues, a recombination operator inspired by the biological combinatorial recombination is proposed at first. The recombination operator could generate the promising candidate solution to enhance search ability of the CSA by fusing the information from random chosen parents. Furthermore, a modified hypermutation operator is introduced to construct more promising and efficient candidate solutions. A set of 16 common used benchmark functions are adopted to test the effectiveness and efficiency of the recombination and hypermutation operators. The comparisons with classic CSA, CSA with recombination operator (RCSA), and CSA with recombination and modified hypermutation operator (RHCSA) demonstrate that the proposed algorithm significantly improves the performance of classic CSA. Moreover, comparison with the state-of-the-art algorithms shows that the proposed algorithm is quite competitive. PMID:27698662

Challenges for operational forecasting and early warning of rainfall induced landslides

NASA Astrophysics Data System (ADS)

Guzzetti, Fausto

2017-04-01

In many areas of the world, landslides occur every year, claiming lives and producing severe economic and environmental damage. Many of the landslides with human or economic consequences are the result of intense or prolonged rainfall. For this reason, in many areas the timely forecast of rainfall-induced landslides is of both scientific interest and social relevance. In the recent years, there has been a mounting interest and an increasing demand for operational landslide forecasting, and for associated landslide early warning systems. Despite the relevance of the problem, and the increasing interest and demand, only a few systems have been designed, and are currently operated. Inspection of the - limited - literature on operational landslide forecasting, and on the associated early warning systems, reveals that common criteria and standards for the design, the implementation, the operation, and the evaluation of the performances of the systems, are lacking. This limits the possibility to compare and to evaluate the systems critically, to identify their inherent strengths and weaknesses, and to improve the performance of the systems. Lack of common criteria and of established standards can also limit the credibility of the systems, and consequently their usefulness and potential practical impact. Landslides are very diversified phenomena, and the information and the modelling tools used to attempt landslide forecasting vary largely, depending on the type and size of the landslides, the extent of the geographical area considered, the timeframe of the forecasts, and the scope of the predictions. Consequently, systems for landslide forecasting and early warning can be designed and implemented at several different geographical scales, from the local (site or slope specific) to the regional, or even national scale. The talk focuses on regional to national scale landslide forecasting systems, and specifically on operational systems based on empirical rainfall threshold models. Building on the experience gained in designing, implementing, and operating national and regional landslide forecasting systems in Italy, and on a preliminary review of the existing literature on regional landslide early warning systems, the talk discusses concepts, limitations and challenges inherent to the design of reliable forecasting and early warning systems for rainfall-triggered landslides, the evaluation of the performances of the systems, and on problems related to the use of the forecasts and the issuing of landslide warnings. Several of the typical elements of an operational landslide forecasting system are considered, including: (i) the rainfall and landslide information used to establish the threshold models, (ii) the methods and tools used to define the empirical rainfall thresholds, and their associated uncertainty, (iii) the quality (e.g., the temporal and spatial resolution) of the rainfall information used for operational forecasting, including rain gauge and radar measurements, satellite estimates, and quantitative weather forecasts, (iv) the ancillary information used to prepare the forecasts, including e.g., the terrain subdivisions and the landslide susceptibility zonations, (v) the criteria used to transform the forecasts into landslide warnings and the methods used to communicate the warnings, and (vi) the criteria and strategies adopted to evaluate the performances of the systems, and to define minimum or optimal performance levels.

Using A Model-Based Systems Engineering Approach For Exploration Medical System Development

NASA Technical Reports Server (NTRS)

Hanson, A.; Mindock, J.; McGuire, K.; Reilly, J.; Cerro, J.; Othon, W.; Rubin, D.; Urbina, M.; Canga, M.

2017-01-01

NASA's Human Research Program's Exploration Medical Capabilities (ExMC) element is defining the medical system needs for exploration class missions. ExMC's Systems Engineering (SE) team will play a critical role in successful design and implementation of the medical system into exploration vehicles. The team's mission is to "Define, develop, validate, and manage the technical system design needed to implement exploration medical capabilities for Mars and test the design in a progression of proving grounds." Development of the medical system is being conducted in parallel with exploration mission architecture and vehicle design development. Successful implementation of the medical system in this environment will require a robust systems engineering approach to enable technical communication across communities to create a common mental model of the emergent engineering and medical systems. Model-Based Systems Engineering (MBSE) improves shared understanding of system needs and constraints between stakeholders and offers a common language for analysis. The ExMC SE team is using MBSE techniques to define operational needs, decompose requirements and architecture, and identify medical capabilities needed to support human exploration. Systems Modeling Language (SysML) is the specific language the SE team is utilizing, within an MBSE approach, to model the medical system functional needs, requirements, and architecture. Modeling methods are being developed through the practice of MBSE within the team, and tools are being selected to support meta-data exchange as integration points to other system models are identified. Use of MBSE is supporting the development of relationships across disciplines and NASA Centers to build trust and enable teamwork, enhance visibility of team goals, foster a culture of unbiased learning and serving, and be responsive to customer needs. The MBSE approach to medical system design offers a paradigm shift toward greater integration between vehicle and the medical system and directly supports the transition of Earth-reliant ISS operations to the Earth-independent operations envisioned for Mars. Here, we describe the methods and approach to building this integrated model.

Lessons Learned from Engineering a Multi-Mission Satellite Operations Center

NASA Technical Reports Server (NTRS)

Madden, Maureen; Cary, Everett, Jr.; Esposito, Timothy; Parker, Jeffrey; Bradley, David

2006-01-01

NASA's Small Explorers (SMEX) satellites have surpassed their designed science-lifetimes and their flight operations teams are now facing the challenge of continuing operations with reduced funding. At present, these missions are being reengineered into a fleet-oriented ground system at Goddard Space Flight Center (GSFC). When completed, this ground system will provide command and control of four SMEX missions and will demonstrate fleet automation and control concepts. As a path-finder for future mission consolidation efforts, this ground system will also demonstrate new ground-based technologies that show promise of supporting longer mission lifecycles and simplifying component integration. One of the core technologies being demonstrated in the SMEiX Mission Operations Center is the GSFC Mission Services Evolution Center (GMSEC) architecture. The GMSEC architecture uses commercial Message Oriented Middleware with a common messaging standard to realize a higher level of component interoperability, allowing for interchangeable components in ground systems. Moreover, automation technologies utilizing the GMSEC architecture are being evaluated and implemented to provide extended lights-out operations. This mode of operation will provide routine monitoring and control of the heterogeneous spacecraft fleet. The operational concepts being developed will reduce the need for staffed contacts and is seen as a necessity for fleet management. This paper will describe the experiences of the integration team throughout the reengineering effort of the SMEX ground system. Additionally, lessons learned will be presented based on the team s experiences with integrating multiple missions into a fleet-based automated ground system.

Lessons Learned from Engineering a Multi-Mission Satellite Operations Center

NASA Technical Reports Server (NTRS)

Madden, Maureen; Cary, Everett, Jr.; Esposito, Timothy; Parker, Jeffrey; Bradley, David

2006-01-01

NASA's Small Explorers (SMEX) satellites have surpassed their designed science-lifetimes and their flight operations teams are now facing the challenge of continuing operations with reduced funding. At present, these missions are being re-engineered into a fleet-oriented ground system at Goddard Space Flight Center (GSFC). When completed, this ground system will provide command and control of four SMEX missions and will demonstrate fleet automation and control concepts. As a path-finder for future mission consolidation efforts, this ground system will also demonstrate new ground-based technologies that show promise of supporting longer mission lifecycles and simplifying component integration. One of the core technologies being demonstrated in the SMEX Mission Operations Center is the GSFC Mission Services Evolution Center (GMSEC) architecture. The GMSEC architecture uses commercial Message Oriented Middleware with a common messaging standard to realize a higher level of component interoperability, allowing for interchangeable components in ground systems. Moreover, automation technologies utilizing the GMSEC architecture are being evaluated and implemented to provide extended lights-out operations. This mode of operation will provide routine monitoring and control of the heterogeneous spacecraft fleet. The operational concepts being developed will reduce the need for staffed contacts and is seen as a necessity for fleet management. This paper will describe the experiences of the integration team throughout the re-enginering effort of the SMEX ground system. Additionally, lessons learned will be presented based on the team's experiences with integrating multiple missions into a fleet-automated ground system.

Rocket Testing and Integrated System Health Management

NASA Technical Reports Server (NTRS)

Figueroa, Fernando; Schmalzel, John

2005-01-01

Integrated System Health Management (ISHM) describes a set of system capabilities that in aggregate perform: determination of condition for each system element, detection of anomalies, diagnosis of causes for anomalies, and prognostics for future anomalies and system behavior. The ISHM should also provide operators with situational awareness of the system by integrating contextual and timely data, information, and knowledge (DIaK) as needed. ISHM capabilities can be implemented using a variety of technologies and tools. This chapter provides an overview of ISHM contributing technologies and describes in further detail a novel implementation architecture along with associated taxonomy, ontology, and standards. The operational ISHM testbed is based on a subsystem of a rocket engine test stand. Such test stands contain many elements that are common to manufacturing systems, and thereby serve to illustrate the potential benefits and methodologies of the ISHM approach for intelligent manufacturing.

A 3D metrology system for the GMT

NASA Astrophysics Data System (ADS)

Rakich, A.; Dettmann, Lee; Leveque, S.; Guisard, S.

2016-08-01

The Giant Magellan Telescope (GMT)1 is a 25 m telescope composed of seven 8.4 m "unit telescopes", on a common mount. Each primary and conjugated secondary mirror segment will feed a common instrument interface, their focal planes co-aligned and co-phased. During telescope operation, the alignment of the optical components will deflect due to variations in thermal environment and gravity induced structural flexure of the mount. The ultimate co-alignment and co-phasing of the telescope is achieved by a combination of the Acquisition Guiding and Wavefront Sensing system and two segment edge-sensing systems2. An analysis of the capture range of the wavefront sensing system indicates that it is unlikely that that system will operate efficiently or reliably with initial mirror positions provided by open-loop corrections alone3. The project is developing a Telescope Metrology System (TMS) which incorporates a large number of absolute distance measuring interferometers. The system will align optical components of the telescope to the instrument interface to (well) within the capture range of the active optics wavefront sensing systems. The advantages offered by this technological approach to a TMS, over a network of laser trackers, are discussed. Initial investigations of the Etalon Absolute Multiline Technology™ by Etalon Ag4 show that a metrology network based on this product is capable of meeting requirements. A conceptual design of the system is presented and expected performance is discussed.

Laparoscopic cholecystectomy for a left-sided gallbladder.

PubMed

Iskandar, Mazen E; Radzio, Agnes; Krikhely, Merab; Leitman, I Michael

2013-09-21

Cholecystectomy is a common procedure. Abnormalities in the anatomy of the biliary system are common but an abnormal location of the gallbladder is much rarer. Despite frequent pre-operative imaging, the aberrant location of the gallbladder is commonly discovered at surgery. This article presents a case of a patient with the gallbladder located to the left of the falciform ligament in the absence of situs inversus totalis that presented with right upper quadrant pain. A laparoscopic cholecystectomy was performed and it was noted that the cystic duct originated from the right side. The presence of a left sided gall bladder is often associated with various biliary, portal venous and other anomalies that might lead to intra-operative injuries. The spectrum of unusual positions and anatomical gallbladder abnormalities is reviewed in order to facilitate elective and emergent cholecystectomy as well as other hepatobiliary procedures. With proper identification of the anatomy, minimally invasive approaches are still considered safe.

Laparoscopic cholecystectomy for a left-sided gallbladder

PubMed Central

Iskandar, Mazen E; Radzio, Agnes; Krikhely, Merab; Leitman, I Michael

2013-01-01

Cholecystectomy is a common procedure. Abnormalities in the anatomy of the biliary system are common but an abnormal location of the gallbladder is much rarer. Despite frequent pre-operative imaging, the aberrant location of the gallbladder is commonly discovered at surgery. This article presents a case of a patient with the gallbladder located to the left of the falciform ligament in the absence of situs inversus totalis that presented with right upper quadrant pain. A laparoscopic cholecystectomy was performed and it was noted that the cystic duct originated from the right side. The presence of a left sided gall bladder is often associated with various biliary, portal venous and other anomalies that might lead to intra-operative injuries. The spectrum of unusual positions and anatomical gallbladder abnormalities is reviewed in order to facilitate elective and emergent cholecystectomy as well as other hepatobiliary procedures. With proper identification of the anatomy, minimally invasive approaches are still considered safe. PMID:24124340

Engineering low-temperature expression systems for heterologous production of cold-adapted enzymes.

PubMed

Bjerga, Gro Elin Kjæreng; Lale, Rahmi; Williamson, Adele Kim

2016-01-01

Production of psychrophilic enzymes in the commonly used mesophilic expression systems is hampered by low intrinsic stability of the recombinant enzymes at the optimal host growth temperatures. Unless strategies for low-temperature expression are advanced, research on psychrophilic enzymes may end up being biased toward those that can be stably produced in commonly used mesophilic host systems. Two main strategies are currently being explored for the development of low-temperature expression in bacterial hosts: (i) low-temperature adaption of existing mesophilic expression systems, and (ii) development of new psychrophilic hosts. These developments include genetic engineering of the expression cassettes to optimize the promoter/operator systems that regulate heterologous expression. In this addendum we present our efforts in the development of such low-temperature expression systems, and speculate about future advancements in the field and potential applications.

Robust 300 C wire insulation system

NASA Technical Reports Server (NTRS)

Nairus, John G.

1994-01-01

The objective of this program is to identify, develop, and demonstrate an optimum wire insulation system that is capable of continuous operation at 300 C. The system is to possess a combination of superior electrical (AC or DC), mechanical, and physical properties over the KAPTON (trademark) derived insulations described in MIL-W-81381 and those hybrid constructions identified in Air Force contract F33615-89-C-5606, commonly known as TKT constructions.

Organizing for intelligent transportation systems : case study of emergency operations in San Francisco Bay area

DOT National Transportation Integrated Search

1997-01-01

Computer-integrated transportation (CIT) is envisioned as an integrated network of public and private transportation organizations, each with unique responsibilities but working toward a common mission of facilitating travel across all modes of trans...

USEPA Guidance for Designing a Source Water Monitoring System

EPA Science Inventory

Treatment plants are commonly designed and operated to handle typical variability in source water quality, treat contaminants known to occur in source water, comply with drinking water standards, and meet customer expectations. However, unanticipated changes in source water qual...

An integral nuclear power and propulsion system concept

NASA Astrophysics Data System (ADS)

Choong, Phillip T.; Teofilo, Vincent L.; Begg, Lester L.; Dunn, Charles; Otting, William

An integral space power concept provides both the electrical power and propulsion from a common heat source and offers superior performance capabilities over conventional orbital insertion using chemical propulsion systems. This paper describes a hybrid (bimodal) system concept based on a proven, inherently safe solid fuel form for the high temperature reactor core operation and rugged planar thermionic energy converter for long-life steady state electric power production combined with NERVA-based rocket technology for propulsion. The integral system is capable of long-life power operation and multiple propulsion operations. At an optimal thrust level, the integral system can maintain the minimal delta-V requirement while minimizing the orbital transfer time. A trade study comparing the overall benefits in placing large payloads to GEO with the nuclear electric propulsion option shows superiority of nuclear thermal propulsion. The resulting savings in orbital transfer time and the substantial reduction of overall lift requirement enables the use of low-cost launchers for several near-term military satellite missions.

Re-engineering Nascom's network management architecture

NASA Technical Reports Server (NTRS)

Drake, Brian C.; Messent, David

1994-01-01

The development of Nascom systems for ground communications began in 1958 with Project Vanguard. The low-speed systems (rates less than 9.6 Kbs) were developed following existing standards; but, there were no comparable standards for high-speed systems. As a result, these systems were developed using custom protocols and custom hardware. Technology has made enormous strides since the ground support systems were implemented. Standards for computer equipment, software, and high-speed communications exist and the performance of current workstations exceeds that of the mainframes used in the development of the ground systems. Nascom is in the process of upgrading its ground support systems and providing additional services. The Message Switching System (MSS), Communications Address Processor (CAP), and Multiplexer/Demultiplexer (MDM) Automated Control System (MACS) are all examples of Nascom systems developed using standards such as, X-windows, Motif, and Simple Network Management Protocol (SNMP). Also, the Earth Observing System (EOS) Communications (Ecom) project is stressing standards as an integral part of its network. The move towards standards has produced a reduction in development, maintenance, and interoperability costs, while providing operational quality improvement. The Facility and Resource Manager (FARM) project has been established to integrate the Nascom networks and systems into a common network management architecture. The maximization of standards and implementation of computer automation in the architecture will lead to continued cost reductions and increased operational efficiency. The first step has been to derive overall Nascom requirements and identify the functionality common to all the current management systems. The identification of these common functions will enable the reuse of processes in the management architecture and promote increased use of automation throughout the Nascom network. The MSS, CAP, MACS, and Ecom projects have indicated the potential value of commercial-off-the-shelf (COTS) and standards through reduced cost and high quality. The FARM will allow the application of the lessons learned from these projects to all future Nascom systems.

Open Architecture SDR for Space

NASA Technical Reports Server (NTRS)

Smith, Carl; Long, Chris; Liebetreu, John; Reinhart, Richard C.

2005-01-01

This paper describes an open-architecture SDR (software defined radio) infrastructure that is suitable for space-based operations (Space-SDR). SDR technologies will endow space and planetary exploration systems with dramatically increased capability, reduced power consumption, and significantly less mass than conventional systems, at costs reduced by vigorous competition, hardware commonality, dense integration, reduced obsolescence, interoperability, and software re-use. Significant progress has been recorded on developments like the Joint Tactical Radio System (JSTRS) Software Communication Architecture (SCA), which is oriented toward reconfigurable radios for defense forces operating in multiple theaters of engagement. The JTRS-SCA presents a consistent software interface for waveform development, and facilitates interoperability, waveform portability, software re-use, and technology evolution.

Event Oriented Design and Adaptive Multiprocessing

DTIC Science & Technology

1991-08-31

System 5 2.3 The Classification 5 2.4 Real-Time Systems 7 2.5 Non Real-Time Systems 10 2.6 Common Characterizations of all Software Systems 10 2.7... Non -Optimal Guarantee Test Theorem 37 6.3.2 Chetto’s Optimal Guarantee Test Theorem 37 6.3.3 Multistate Case: An Extended Guarantee 39 Test Theorem...which subdivides all software systems according to the way in which they operate, such as interactive, non interactive, real-time, etc. Having defined

Biofiltration of volatile pollutants: Engineering mechanisms for improved design, long-term operation, prediction and implementation. 1998 annual progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, B.H.; Klasson, K.T.; Barton, J.W.

1998-06-01

'Biofiltration systems can be used for treatment of volatile organic compounds (VOCs); however, the systems are poorly understood and are currently operated as black boxes. Common operational problems associated with biofilters include fouling, deactivation, and overgrowth, all of which make them ineffective for continuous, long-term use. The objective of this investigation is to develop generic methods for long-term stable operation, in particular by using selective limitation of supplemental nutrients while maintaining high activity. As part of this effort, the author will provide deeper fundamental understanding of the important biological and transport mechanisms in biodestruction of sparingly soluble VOCs and extendmore » this approach and mathematical models to additional systems of high priority EM relevance--direct degradation and cometabolic degradation of priority pollutants such as BTEX and chlorinated organics. This report summarizes work after 2 years of a 3-year project. Major results are enumerated and discussed'« less

Meta-manager: a requirements analysis.

PubMed

Cook, J F; Rozenblit, J W; Chacko, A K; Martinez, R; Timboe, H L

1999-05-01

The digital imaging network-picture-archiving and communications system (DIN-PACS) will be implemented in ten sites within the Great Plains Regional Medical Command (GPRMC). This network of PACS and teleradiology technology over a shared T1 network has opened the door for round the clock radiology coverage of all sites. However, the concept of a virtual radiology environment poses new issues for military medicine. A new workflow management system must be developed. This workflow management system will allow us to efficiently resolve these issues including quality of care, availability, severe capitation, and quality of the workforce. The design process of this management system must employ existing technology, operate over various telecommunication networks and protocols, be independent of platform operating systems, be flexible and scaleable, and involve the end user at the outset in the design process for which it is developed. Using the unified modeling language (UML), the specifications for this new business management system were created in concert between the University of Arizona and the GPRMC. These specifications detail a management system operating through a common object request brokered architecture (CORBA) environment. In this presentation, we characterize the Meta-Manager management system including aspects of intelligence, interfacility routing, fail-safe operations, and expected improvements in patient care and efficiency.

A reagent-free tubular biofilm reactor for on-line determination of biochemical oxygen demand.

PubMed

Liu, Changyu; Zhao, Huijun; Gao, Shan; Jia, Jianbo; Zhao, Limin; Yong, Daming; Dong, Shaojun

2013-07-15

We reported a reagent-free tubular biofilm reactor (BFR) based analytical system for rapid online biochemical oxygen demand (BOD) determination. The BFR was cultivated using microbial seeds from activated sludge. It only needs tap water to operate and does not require any chemical reagent. The analytical performance of this reagent-free BFR system was found to be equal to or better than the BFR system operated using phosphate buffer saline (PBS) and high purity deionized water. The system can readily achieve a limit of detection of 0.25 mg O2 L(-1), possessing superior reproducibility, and long-term operational and storage stability. More importantly, we confirmed for the first time that the BFR system is capable of tolerating common toxicants found in wastewaters, such as 3,5-dichlorophenol and Zn(II), Cr(VI), Cd(II), Cu(II), Pb(II), Mn(II) and Ni(II), enabling the method to be applied to a wide range of wastewaters. The sloughing and clogging are the important attributes affecting the operational stability, hence, the reliability of most online wastewater monitoring systems, which can be effectively avoided, benefiting from the tubular geometry of the reactor and high flow rate conditions. These advantages, coupled with simplicity in device, convenience in operation and minimal maintenance, make such a reagent-free BFR analytical system promising for practical BOD online determination. Copyright © 2013 Elsevier B.V. All rights reserved.

47 CFR 27.66 - Discontinuance, reduction, or impairment of service.

Code of Federal Regulations, 2013 CFR

2013-10-01

... licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager, is... carrier licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager... fixed non-common carrier licensee, or a fixed non-common carrier operating on spectrum licensed to a...

47 CFR 27.66 - Discontinuance, reduction, or impairment of service.

Code of Federal Regulations, 2014 CFR

2014-10-01

... licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager, is... carrier licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager... fixed non-common carrier licensee, or a fixed non-common carrier operating on spectrum licensed to a...

47 CFR 27.66 - Discontinuance, reduction, or impairment of service.

Code of Federal Regulations, 2012 CFR

2012-10-01

... licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager, is... carrier licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager... fixed non-common carrier licensee, or a fixed non-common carrier operating on spectrum licensed to a...

47 CFR 27.66 - Discontinuance, reduction, or impairment of service.

Code of Federal Regulations, 2011 CFR

2011-10-01

... licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager, is... carrier licensee, or a fixed common carrier operating on spectrum licensed to a Guard Band Manager... fixed non-common carrier licensee, or a fixed non-common carrier operating on spectrum licensed to a...

Innovative and applied research on big data platforms of smart heritage

NASA Astrophysics Data System (ADS)

Qiu, J.; Li, J.; Sun, H.

2015-08-01

Big data has huge commercial value and potential. Under the background of big data, a heritage site is faced with a number of questions and challenges such as, how to accelerate industrial innovation, benign competition and the creation of new business value. Based on the analysis of service data from the national archaeological site and park, Yuan Ming Yuan, this paper investigates the common problems of site management operations such as, inappropriate cultural interpretation, insufficient consumer demand and so on. In order to solve these operational problems, a new service system called the "one platform - three systems" was put forward. This system includes the smart heritage platform and three management systems: the smart heritage management system, the 3-O (Online-Offline-Onsite) service system and the digital explanation system. Combined with the 3-O marketing operation, the platform can realize bidirectional interaction between heritage site management units and tourists, which can also benefit visitors to the heritage site by explaining the culture and history of the heritage site, bring about more demand for cultural information and expand the social and economic benefits.

Architecting Communication Network of Networks for Space System of Systems

NASA Technical Reports Server (NTRS)

Bhasin, Kul B.; Hayden, Jeffrey L.

2008-01-01

The National Aeronautics and Space Administration (NASA) and the Department of Defense (DoD) are planning Space System of Systems (SoS) to address the new challenges of space exploration, defense, communications, navigation, Earth observation, and science. In addition, these complex systems must provide interoperability, enhanced reliability, common interfaces, dynamic operations, and autonomy in system management. Both NASA and the DoD have chosen to meet the new demands with high data rate communication systems and space Internet technologies that bring Internet Protocols (IP), routers, servers, software, and interfaces to space networks to enable as much autonomous operation of those networks as possible. These technologies reduce the cost of operations and, with higher bandwidths, support the expected voice, video, and data needed to coordinate activities at each stage of an exploration mission. In this paper, we discuss, in a generic fashion, how the architectural approaches and processes are being developed and used for defining a hypothetical communication and navigation networks infrastructure to support lunar exploration. Examples are given of the products generated by the architecture development process.

Defense Acquisitions: Assessments of Selected Weapon Programs

DTIC Science & Technology

2009-03-01

a field experiment , but program officials report that it will take additional efforts to transition the waveform to an operational platform. The...successfully demonstrated during a field experiment ending in October 2008 that included a multi-subnet test by Future Combat Systems personnel. The...Individual Programs 29 Advanced Extremely High Frequency (AEHF) Satellites 31 Advanced Threat Infrared Countermeasure/Common Missile Warning System

School Principals' Perceptions of "Basic Values" in the Swedish Compulsory School System in Regard to Bronfenbrenner's Ecological Systems Theory

ERIC Educational Resources Information Center

Drakenberg, Margareth; Malmgren, Therese Vincenti

2013-01-01

The purpose of this study is to compare how Swedish school principals understand basic values that are important in fulfilling the Swedish national curriculum, Curriculum 1994 (a new curriculum, Curriculum 2011, which came into operation in autumn 2011, has only minor differences compared to the common text in Curriculum 1994), considering…

Rotorcraft System Identification (Identification des Systemes de Voilures Tournantes)

DTIC Science & Technology

1991-10-01

the NATO community; - Providing scientific and technical advice and assistance to the Military Committee in the field of aerospace research and...common defence posture, - Improving the co-operation among member nations in aerospace research and development. - Exchange of scientific and...technical information; - Prcviding assistance to member nations for the purpose of increasing their scientific and technical potential, - Rendenng scientific

A systematic review of the extent, nature and likely causes of preventable adverse events arising from hospital care.

PubMed

Sari, A Akbari; Doshmangir, L; Sheldon, T

2010-01-01

Understanding the nature and causes of medical adverse events may help their prevention. This systematic review explores the types, risk factors, and likely causes of preventable adverse events in the hospital sector. MEDLINE (1970-2008), EMBASE, CINAHL (1970-2005) and the reference lists were used to identify the studies and a structured narrative method used to synthesise the data. Operative adverse events were more common but less preventable and diagnostic adverse events less common but more preventable than other adverse events. Preventable adverse events were often associated with more than one contributory factor. The majority of adverse events were linked to individual human error, and a significant proportion of these caused serious patient harm. Equipment failure was involved in a small proportion of adverse events and rarely caused patient harm. The proportion of system failures varied widely ranging from 3% to 85% depending on the data collection and classification methods used. Operative adverse events are more common but less preventable than diagnostic adverse events. Adverse events are usually associated with more than one contributory factor, the majority are linked to individual human error, and a proportion of these with system failure.

Constructed wetlands for wastewater and activated sludge treatment in north Greece: a review.

PubMed

Tsihrintzis, V A; Gikas, G D

2010-01-01

Constructed wetlands used for the treatment of urban, industrial and agricultural wastewater have become very popular treatment systems all over the world. In Greece, these systems are not very common, although the climate is favourable for their use. During recent years, there have been several attempts for the implementation of these systems in Greece, which include, among others, pilot-scale systems used for research, and full-scale systems designed and/or constructed to serve settlements or families. The purpose of this paper is the presentation of systems operating in Northern Greece, which have been studied by the Laboratory of Ecological Engineering and Technology of Democritus University of Thrace and others. A comparison is made of different system types, and the effect of various design and operational parameters is presented. Current research shows the good and continuous performance of these systems.

Space station integrated propulsion and fluid systems study. Space station program fluid management systems databook

NASA Technical Reports Server (NTRS)

Bicknell, B.; Wilson, S.; Dennis, M.; Lydon, M.

1988-01-01

Commonality and integration of propulsion and fluid systems associated with the Space Station elements are being evaluated. The Space Station elements consist of the core station, which includes habitation and laboratory modules, nodes, airlocks, and trusswork; and associated vehicles, platforms, experiments, and payloads. The program is being performed as two discrete tasks. Task 1 investigated the components of the Space Station architecture to determine the feasibility and practicality of commonality and integration among the various propulsion elements. This task was completed. Task 2 is examining integration and commonality among fluid systems which were identified by the Phase B Space Station contractors as being part of the initial operating capability (IOC) and growth Space Station architectures. Requirements and descriptions for reference fluid systems were compiled from Space Station documentation and other sources. The fluid systems being examined are: an experiment gas supply system, an oxygen/hydrogen supply system, an integrated water system, the integrated nitrogen system, and the integrated waste fluids system. Definitions and descriptions of alternate systems were developed, along with analyses and discussions of their benefits and detriments. This databook includes fluid systems descriptions, requirements, schematic diagrams, component lists, and discussions of the fluid systems. In addition, cost comparison are used in some cases to determine the optimum system for a specific task.

47 CFR 32.6113 - Aircraft expense.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Aircraft expense. 32.6113 Section 32.6113 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS... account for amounts transferred to Construction and/or to other Plant Specific Operations Expense accounts...

Video Vehicle Detector Verification System (V2DVS) operators manual and project final report.

DOT National Transportation Integrated Search

2012-03-01

The accurate detection of the presence, speed and/or length of vehicles on roadways is recognized as critical for : effective roadway congestion management and safety. Vehicle presence sensors are commonly used for traffic : volume measurement and co...

47 CFR 32.6113 - Aircraft expense.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Aircraft expense. 32.6113 Section 32.6113 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS... account for amounts transferred to Construction and/or to other Plant Specific Operations Expense accounts...

SCALE-MODEL STUDIES OF MIXING IN DRINKING WATER STORAGE TANKS

EPA Science Inventory

Storage tanks and reservoirs are commonly used in drinking water distribution systems to equalize pumping requirements and operating pressures, and to provide emergency water for fire-fighting and pumping outages. Poor mixing in these structures can create pockets of older water...

47 CFR 22.946 - Service commencement and construction systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... 22.946 Section 22.946 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES PUBLIC MOBILE SERVICES Cellular Radiotelephone Service § 22.946 Service commencement and... telephone network (PSTN) and must be providing service to mobile stations operated by its subscribers and...

Mars Surface Systems Common Capabilities and Challenges for Human Missions

NASA Technical Reports Server (NTRS)

Toups, Larry; Hoffman, Stephen J.; Watts, Kevin

2016-01-01

This paper describes the current status of common systems and operations as they are applied to actual locations on Mars that are representative of Exploration Zones (EZ) - NASA's term for candidate locations where humans could land, live and work on the martian surface. Given NASA's current concepts for human missions to Mars, an EZ is a collection of Regions of Interest (ROIs) located within approximately 100 kilometers of a centralized landing site. ROIs are areas that are relevant for scientific investigation and/or development/maturation of capabilities and resources necessary for a sustainable human presence. An EZ also contains a habitation site that will be used by multiple human crews during missions to explore and utilize the ROIs within the EZ. The Evolvable Mars Campaign (EMC), a description of NASA's current approach to these human Mars missions, assumes that a single EZ will be identified within which NASA will establish a substantial and durable surface infrastructure that will be used by multiple human crews. The process of identifying and eventually selecting this single EZ will likely take many years to finalized. Because of this extended EZ selection process it becomes important to evaluate the current suite of surface systems and operations being evaluated for the EMC as they are likely to perform at a variety of proposed EZ locations and for the types of operations - both scientific and development - that are proposed for these candidate EZs. It is also important to evaluate proposed EZs for their suitability to be explored or developed given the range of capabilities and constraints for the types of surface systems and operations being considered within the EMC.

Predicting System Accidents with Model Analysis During Hybrid Simulation

NASA Technical Reports Server (NTRS)

Malin, Jane T.; Fleming, Land D.; Throop, David R.

2002-01-01

Standard discrete event simulation is commonly used to identify system bottlenecks and starving and blocking conditions in resources and services. The CONFIG hybrid discrete/continuous simulation tool can simulate such conditions in combination with inputs external to the simulation. This provides a means for evaluating the vulnerability to system accidents of a system's design, operating procedures, and control software. System accidents are brought about by complex unexpected interactions among multiple system failures , faulty or misleading sensor data, and inappropriate responses of human operators or software. The flows of resource and product materials play a central role in the hazardous situations that may arise in fluid transport and processing systems. We describe the capabilities of CONFIG for simulation-time linear circuit analysis of fluid flows in the context of model-based hazard analysis. We focus on how CONFIG simulates the static stresses in systems of flow. Unlike other flow-related properties, static stresses (or static potentials) cannot be represented by a set of state equations. The distribution of static stresses is dependent on the specific history of operations performed on a system. We discuss the use of this type of information in hazard analysis of system designs.

Ion extraction capabilities of two-grid accelerator systems. [for spacecraft propulsion

NASA Technical Reports Server (NTRS)

Rovang, D. C.; Wilbur, P. J.

1984-01-01

An experimental investigation into the ion extraction capabilities of two-grid accelerator systems common to electrostatic ion thrusters is described. A large body of experimental data which facilitates the selection of the accelerator system geometries and operating parameters necessary to maximize the extracted ion current is presented. Results suggest that the impingement-limited perveance is not dramatically affected by reductions in screen hole diameter to 0.5 mm. Impingement-limited performance is shown to depend most strongly on grid separation distance, accelerator hole diameter ratio, the discharge-to-total accelerating voltage ratio, and the net-to-total accelerating voltage ratio. Results obtained at small grid separation ratios suggest a new grid operating condition where high beam current per hole levels are achieved at a specified net accelerating voltage. It is shown that this operating condition is realized at an optimum ratio of net-to-total accelerating voltage ratio which is typically quite high.

Design Criteria for Vacuum Wastewater Transfer Systems in Advanced Base Applications

DTIC Science & Technology

1979-05-01

costs, and (d) operational man- powe reqiremnts._51 Library Card I Civil Engineering labo~rator% L ~ DISIGN CRITERIA FOR VACUU’tM WASTEWATER ITRANSFER...generated from multiple sources (such as toil-ts, kitchens , laundries, and showers) and transported in a single, common transport main. Although special...system)(Ref 1) 2. A single-pipe system in parallel with the other where gray water sources (shower, laundry, and kitchen types of wastewaters) are

Challenges in Achieving Trajectory-Based Operations

NASA Technical Reports Server (NTRS)

Cate, Karen Tung

2012-01-01

In the past few years much of the global ATM research community has proposed advanced systems based on Trajectory-Based Operations (TBO). The concept of TBO uses four-dimensional aircraft trajectories as the base information for managing safety and capacity. Both the US and European advanced ATM programs call for the sharing of trajectory data across different decision support tools for successful operations. However, the actual integration of TBO systems presents many challenges. Trajectory predictors are built to meet the specific needs of a particular system and are not always compatible with others. Two case studies are presented which examine the challenges of introducing a new concept into two legacy systems in regards to their trajectory prediction software. The first case describes the issues with integrating a new decision support tool with a legacy operational system which overlap in domain space. These tools perform similar functions but are driven by different requirements. The difference in the resulting trajectories can lead to conflicting advisories. The second case looks at integrating this same new tool with a legacy system originally developed as an integrated system, but diverged many years ago. Both cases illustrate how the lack of common architecture concepts for the trajectory predictors added cost and complexity to the integration efforts.

Medical lighting composed of LED arrays for surgical operation

NASA Astrophysics Data System (ADS)

Shimada, Junichi; Kawakami, Yoichi; Fujita, Shigeo

2001-05-01

Everywhere in the world, the highest quality and quantity of lighting is required during the surgical operations. However, the surgical approach has had many types and various angles, common ceiling surgical halogen lighting system cannot provide an adequate amount of beams because the surgeons' heads hinder the illuminations from reaching the operation field. Here, we newly design surgical lighting system composed of white LEDs equipped on both sides of goggles, which controls the lighting beams to the gazing point. With this system, it is just needed for surgeons to wear light plastic goggles with high quality LEDs made by Nichia. In fact, we have succeeded in the first internal shunt operation in the left forearm using the surgical LED lighting system on 11th Sept 2000. The electrical power for the system was supplied from lithium-ion battery for 2 hours. Since the white LEDs used were composed of InGaN- blue-emitters and YAG-yellow-phosphors, the color rendering property was not sufficient in the reddish colors. Therefore, in the next approach, it is very important to develop the spectral distribution of white LED to render inherent color of raw flesh such as skin, blood, fat tissue and internal organs.

Extensions to the Parallel Real-Time Artificial Intelligence System (PRAIS) for fault-tolerant heterogeneous cycle-stealing reasoning

NASA Technical Reports Server (NTRS)

Goldstein, David

1991-01-01

Extensions to an architecture for real-time, distributed (parallel) knowledge-based systems called the Parallel Real-time Artificial Intelligence System (PRAIS) are discussed. PRAIS strives for transparently parallelizing production (rule-based) systems, even under real-time constraints. PRAIS accomplished these goals (presented at the first annual C Language Integrated Production System (CLIPS) conference) by incorporating a dynamic task scheduler, operating system extensions for fact handling, and message-passing among multiple copies of CLIPS executing on a virtual blackboard. This distributed knowledge-based system tool uses the portability of CLIPS and common message-passing protocols to operate over a heterogeneous network of processors. Results using the original PRAIS architecture over a network of Sun 3's, Sun 4's and VAX's are presented. Mechanisms using the producer-consumer model to extend the architecture for fault-tolerance and distributed truth maintenance initiation are also discussed.

Autonomous Satellite Operations Via Secure Virtual Mission Operations Center

NASA Technical Reports Server (NTRS)

Miller, Eric; Paulsen, Phillip E.; Pasciuto, Michael

2011-01-01

The science community is interested in improving their ability to respond to rapidly evolving, transient phenomena via autonomous rapid reconfiguration, which derives from the ability to assemble separate but collaborating sensors and data forecasting systems to meet a broad range of research and application needs. Current satellite systems typically require human intervention to respond to triggers from dissimilar sensor systems. Additionally, satellite ground services often need to be coordinated days or weeks in advance. Finally, the boundaries between the various sensor systems that make up such a Sensor Web are defined by such things as link delay and connectivity, data and error rate asymmetry, data reliability, quality of service provisions, and trust, complicating autonomous operations. Over the past ten years, researchers from the NASA Glenn Research Center (GRC), General Dynamics, Surrey Satellite Technology Limited (SSTL), Cisco, Universal Space Networks (USN), the U.S. Geological Survey (USGS), the Naval Research Laboratory, the DoD Operationally Responsive Space (ORS) Office, and others have worked collaboratively to develop a virtual mission operations capability. Called VMOC (Virtual Mission Operations Center), this new capability allows cross-system queuing of dissimilar mission unique systems through the use of a common security scheme and published application programming interfaces (APIs). Collaborative VMOC demonstrations over the last several years have supported the standardization of spacecraft to ground interfaces needed to reduce costs, maximize space effects to the user, and allow the generation of new tactics, techniques and procedures that lead to responsive space employment.

Metrological Software Test for Simulating the Method of Determining the Thermocouple Error in Situ During Operation

NASA Astrophysics Data System (ADS)

Chen, Jingliang; Su, Jun; Kochan, Orest; Levkiv, Mariana

2018-04-01

The simplified metrological software test (MST) for modeling the method of determining the thermocouple (TC) error in situ during operation is considered in the paper. The interaction between the proposed MST and a temperature measuring system is also reflected in order to study the error of determining the TC error in situ during operation. The modelling studies of the random error influence of the temperature measuring system, as well as interference magnitude (both the common and normal mode noises) on the error of determining the TC error in situ during operation using the proposed MST, have been carried out. The noise and interference of the order of 5-6 μV cause the error of about 0.2-0.3°C. It is shown that high noise immunity is essential for accurate temperature measurements using TCs.

Unreliable numbers: error and harm induced by bad design can be reduced by better design

PubMed Central

Thimbleby, Harold; Oladimeji, Patrick; Cairns, Paul

2015-01-01

Number entry is a ubiquitous activity and is often performed in safety- and mission-critical procedures, such as healthcare, science, finance, aviation and in many other areas. We show that Monte Carlo methods can quickly and easily compare the reliability of different number entry systems. A surprising finding is that many common, widely used systems are defective, and induce unnecessary human error. We show that Monte Carlo methods enable designers to explore the implications of normal and unexpected operator behaviour, and to design systems to be more resilient to use error. We demonstrate novel designs with improved resilience, implying that the common problems identified and the errors they induce are avoidable. PMID:26354830

The need for GPS standardization

NASA Technical Reports Server (NTRS)

Lewandowski, Wlodzimierz W.; Petit, Gerard; Thomas, Claudine

1992-01-01

A desirable and necessary step for improvement of the accuracy of Global Positioning System (GPS) time comparisons is the establishment of common GPS standards. For this reason, the CCDS proposed the creation of a special group of experts with the objective of recommending procedures and models for operational time transfer by GPS common-view method. Since the announcement of the implementation of Selective Availability at the end of last spring, action has become much more urgent and this CCDS Group on GPS Time Transfer Standards has now been set up. It operates under the auspices of the permanent CCDS Working Group on TAI and works in close cooperation with the Sub-Committee on Time of the Civil GPS Service Interface Committee (CGSIC). Taking as an example the implementation of SA during the first week of July 1991, this paper illustrates the need to develop urgently at least two standardized procedures in GPS receiver software: monitoring GPS tracks with a common time scale and retaining broadcast ephemeris parameters throughout the duration of a track. Other matters requiring action are the adoption of common models for atmospheric delay, a common approach to hardware design and agreement about short-term data processing. Several examples of such deficiencies in standardization are presented.

Passive serialization in a multitasking environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hennessey, J.P.; Osisek, D.L.; Seigh, J.W. II

1989-02-28

In a multiprocessing system having a control program in which data objects are shared among processes, this patent describes a method for serializing references to a data object by the processes so as to prevent invalid references to the data object by any process when an operation requiring exclusive access is performed by another process, comprising the steps of: permitting the processes to reference data objects on a shared access basis without obtaining a shared lock; monitoring a point of execution of the control program which is common to all processes in the system, which occurs regularly in the process'more » execution and across which no references to any data object can be maintained by any process, except references using locks; establishing a system reference point which occurs after each process in the system has passed the point of execution at least once since the last such system reference point; requesting an operation requiring exclusive access on a selected data object; preventing subsequent references by other processes to the selected data object; waiting until two of the system references points have occurred; and then performing the requested operation.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brouillette, Greg A.

These are slides for various presentations on C41SR and urban disasters disasters response and recovery tools. These are all mainly charts and images of disaster response and recovery tools. Slides included have headings such as the following: vignette of a disaster response, situational awareness and common operating picture available to EOC, plume modeling capability, Program ASPECT Chemical Response Products, EPA ASPECT - Hurricane RITA Response 9/25/2005, Angel Fire Imagery, incident commander's view/police chief's view/ EMS' view, common situational awareness and collaborative planning, exercise, training capability, systems diagram, Austere Challenge 06 Sim/C4 Requirements, common situational awareness and collaborative planning, exercise, trainingmore » environment, common situational awareness, real world, crisis response, and consequence management.« less

The X-33 range Operations Control Center

NASA Technical Reports Server (NTRS)

Shy, Karla S.; Norman, Cynthia L.

1998-01-01

This paper describes the capabilities and features of the X-33 Range Operations Center at NASA Dryden Flight Research Center. All the unprocessed data will be collected and transmitted over fiber optic lines to the Lockheed Operations Control Center for real-time flight monitoring of the X-33 vehicle. By using the existing capabilities of the Western Aeronautical Test Range, the Range Operations Center will provide the ability to monitor all down-range tracking sites for the Extended Test Range systems. In addition to radar tracking and aircraft telemetry data, the Telemetry and Radar Acquisition and Processing System is being enhanced to acquire vehicle command data, differential Global Positioning System corrections and telemetry receiver signal level status. The Telemetry and Radar Acquisition Processing System provides the flexibility to satisfy all X-33 data processing requirements quickly and efficiently. Additionally, the Telemetry and Radar Acquisition Processing System will run a real-time link margin analysis program. The results of this model will be compared in real-time with actual flight data. The hardware and software concepts presented in this paper describe a method of merging all types of data into a common database for real-time display in the Range Operations Center in support of the X-33 program. All types of data will be processed for real-time analysis and display of the range system status to ensure public safety.

47 CFR 32.6112 - Motor vehicle expense.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Motor vehicle expense. 32.6112 Section 32.6112 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS.../or to other Plant Specific Operations Expense accounts. These amounts shall be computed on the basis...

47 CFR 22.957 - Mexican condition.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Mexican condition. 22.957 Section 22.957 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES PUBLIC MOBILE SERVICES... the system must be advised that operation of a mobile unit in Mexico is not permitted at this time...

SDR/STRS Flight Experiment and the Role of SDR-Based Communication and Navigation Systems

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.

2008-01-01

This presentation describes an open architecture SDR (software defined radio) infrastructure, suitable for space-based radios and operations, entitled Space Telecommunications Radio System (STRS). SDR technologies will endow space and planetary exploration systems with dramatically increased capability, reduced power consumption, and less mass than conventional systems, at costs reduced by vigorous competition, hardware commonality, dense integration, minimizing the impact of parts obsolescence, improved interoperability, and software re-use. To advance the SDR architecture technology and demonstrate its applicability in space, NASA is developing a space experiment of multiple SDRs each with various waveforms to communicate with NASA s TDRSS satellite and ground networks, and the GPS constellation. An experiments program will investigate S-band and Ka-band communications, navigation, and networking technologies and operations.

Orion Entry, Descent, and Landing Performance and Mission Design

NASA Technical Reports Server (NTRS)

Broome, Joel M.; Johnson, Wyatt

2007-01-01

The Orion Vehicle is the next spacecraft to take humans into space and will include missions to ISS as well as missions to the Moon. As part of that challenge, the vehicle will have to accommodate multiple mission design concepts, since return from Low Earth Orbit and return from the Moon can be quite different. Commonality between the different missions as it relates to vehicle systems, guidance capability, and operations concepts is the goal. Several unique mission design concepts include the specification of multiple land-based landing sites for a vehicle with closed-loop direct and skip entry guidance, followed by a parachute descent and landing attenuation system. This includes the ability of the vehicle to accurately target and land at a designated landing site, including site location aspects, landing site size, and landing opportunities assessments. Analyses associated with these mission design and flight performance challenges and constraints will be discussed as well as potential operational concepts to provide feasibility and/or mission commonality.

Research on common methods for evaluating the operation effect of integrated wastewater treatment facilities of iron and steel enterprises

NASA Astrophysics Data System (ADS)

Bingsheng, Xu

2017-04-01

Considering the large quantities of wastewater generated from iron and steel enterprises in China, this paper is aimed to research the common methods applied for evaluating the integrated wastewater treatment effect of iron and steel enterprises. Based on survey results on environmental protection performance, technological economy, resource & energy consumption, services and management, an indicator system for evaluating the operation effect of integrated wastewater treatment facilities is set up. By discussing the standards and industrial policies in and out of China, 27 key secondary indicators are further defined on the basis of investigation on main equipment and key processes for wastewater treatment, so as to determine the method for setting key quantitative and qualitative indicators for evaluation indicator system. It is also expected to satisfy the basic requirements of reasonable resource allocation, environmental protection and sustainable economic development, further improve the integrated wastewater treatment effect of iron and steel enterprises, and reduce the emission of hazardous substances and environmental impact.

Intranets: virtual procedure manuals for the pathology lab.

PubMed

Ruby, S G; Krempel, G

1998-08-01

A novel system exists for replacing standard written operation manuals using a computerized PC-based peer-to-peer network. The system design is based on commonly available hardware and software and utilizes existing equipment to minimize implementation expense. The system is relatively easy to implement and maintain, involves minimal training, and should quickly become a financial asset. In addition, such a system can improve access to laboratory procedure manuals so that resources can be better used on a daily basis.

Integrated waste and water management system

NASA Technical Reports Server (NTRS)

Murray, R. W.; Sauer, R. L.

1986-01-01

The performance requirements of the NASA Space Station have prompted a reexamination of a previously developed integrated waste and water management system that used distillation and catalytic oxydation to purify waste water, and microbial digestion and incineration for waste solids disposal. This system successfully operated continuously for 206 days, for a 4-man equivalent load of urine, feces, wash water, condensate, and trash. Attention is given to synergisms that could be established with other life support systems, in the cases of thermal integration, design commonality, and novel technologies.

[Modern foreign car safety systems and their forensic-medical significance].

PubMed

Iakunin, S A

2007-01-01

The author gives a characteristic of active and passive security systems installed in cars of foreign production. These security systems significantly modify the classic car trauma character decreasing frequency of occurrence and dimensions of specific and typical injuries. A new approach based on the theory of probability to estimate these injuries is required. The most common active and passive security systems are described in the article; their principles of operation and influence on the trauma character are estimated.

Distributed Common Ground System - Army (DCGS-A) Increment 1 Release 2 Follow-on Operational Test and Evaluation (FOT and E) Report

DTIC Science & Technology

2016-01-01

Moving Target Indicator, Unmanned Aircraft System (UAS), Rivet Joint, U-2, and ground signals intelligence (PROPHET). At the BCT, Ranger Regiment and... metadata catalog managed by the DIB management office (outside of the DCGS-A system ). A metadata is a searchable description of data, and users across...challenge for users . The system required reboots about every 20 hours for users who had heavy workloads such as the fire support analysts and data

System Proposal for Mass Transit Service Quality Control Based on GPS Data

PubMed Central

Padrón, Gabino; Cristóbal, Teresa; Alayón, Francisco; Quesada-Arencibia, Alexis; García, Carmelo R.

2017-01-01

Quality is an essential aspect of public transport. In the case of regular public passenger transport by road, punctuality and regularity are criteria used to assess quality of service. Calculating metrics related to these criteria continuously over time and comprehensively across the entire transport network requires the handling of large amounts of data. This article describes a system for continuously and comprehensively monitoring punctuality and regularity. The system uses location data acquired continuously in the vehicles and automatically transferred for analysis. These data are processed intelligently by elements that are commonly used by transport operators: GPS-based tracking system, onboard computer and wireless networks for mobile data communications. The system was tested on a transport company, for which we measured the punctuality of one of the routes that it operates; the results are presented in this article. PMID:28621745

System Proposal for Mass Transit Service Quality Control Based on GPS Data.

PubMed

Padrón, Gabino; Cristóbal, Teresa; Alayón, Francisco; Quesada-Arencibia, Alexis; García, Carmelo R

2017-06-16

Quality is an essential aspect of public transport. In the case of regular public passenger transport by road, punctuality and regularity are criteria used to assess quality of service. Calculating metrics related to these criteria continuously over time and comprehensively across the entire transport network requires the handling of large amounts of data. This article describes a system for continuously and comprehensively monitoring punctuality and regularity. The system uses location data acquired continuously in the vehicles and automatically transferred for analysis. These data are processed intelligently by elements that are commonly used by transport operators: GPS-based tracking system, onboard computer and wireless networks for mobile data communications. The system was tested on a transport company, for which we measured the punctuality of one of the routes that it operates; the results are presented in this article.

Lessons Learned From the Development, Operation, and Review of Mechanical Systems on the Space Shuttle, International Space Station, and Payloads

NASA Technical Reports Server (NTRS)

Dinsel, Alison; Jermstad, Wayne; Robertson, Brandan

2006-01-01

The Mechanical Design and Analysis Branch at the Johnson Space Center (JSC) is responsible for the technical oversight of over 30 mechanical systems flying on the Space Shuttle Orbiter and the International Space Station (ISS). The branch also has the responsibility for reviewing all mechanical systems on all Space Shuttle and International Space Station payloads, as part of the payload safety review process, through the Mechanical Systems Working Group (MSWG). These responsibilities give the branch unique insight into a large number of mechanical systems, and problems encountered during their design, testing, and operation. This paper contains narrative descriptions of lessons learned from some of the major problems worked on by the branch during the last two years. The problems are grouped into common categories and lessons learned are stated.

Binaries discovered by the SPY survey. VI. Discovery of a low mass companion to the hot subluminous planetary nebula central star EGB 5 - a recently ejected common envelope?

NASA Astrophysics Data System (ADS)

Geier, S.; Napiwotzki, R.; Heber, U.; Nelemans, G.

2011-04-01

Hot subdwarf B stars (sdBs) in close binary systems are assumed to be formed via common envelope ejection. According to theoretical models, the amount of energy and angular momentum deposited in the common envelope scales with the mass of the companion. That low mass companions near or below the core hydrogen-burning limit are able to trigger the ejection of this envelope is well known. The currently known systems have very short periods ≃0.1-0.3 d. Here we report the discovery of a low mass companion (M2 > 0.14 M⊙) orbiting the sdB star and central star of a planetary nebula EGB 5 with an orbital period of 16.5 d at a minimum separation of 23 R⊙. Its long period is only just consistent with the energy balance prescription of the common envelope. The marked difference between the short and long period systems will provide strong constraints on the common envelope phase, in particular if the masses of the sdB stars can be measured accurately. Due to selection effects, the fraction of sdBs with low mass companions and similar or longer periods may be quite high. Low mass stellar and substellar companions may therefore play a significant role for the still unclear formation of hot subdwarf stars. Furthermore, the nebula around EGB 5 may be the remnant of the ejected common envelope making this binary a unique system to study this short und poorly understood phase of binary evolution. Based on observations at the Paranal Observatory of the European Southern Observatory for programmes No. 167.H-0407(A) and 71.D-0383(A). Based on observations collected at the Centro Astronómico Hispano Alemán (CAHA) at Calar Alto, operated jointly by the Max-Planck Institut für Astronomie and the Instituto de Astrofísica de Andalucía (CSIC). Some of the data used in this work were obtained at the William Herschel Telescope (WHT) operated by the Isaac Newton Group of Telescopes (ING).

Graphene Ambipolar Nanoelectronics for High Noise Rejection Amplification.

PubMed

Liu, Che-Hung; Chen, Qi; Liu, Chang-Hua; Zhong, Zhaohui

2016-02-10

In a modern wireless communication system, signal amplification is critical for overcoming losses during multiple data transformations/processes and long-distance transmission. Common mode and differential mode are two fundamental amplification mechanisms, and they utilize totally different circuit configurations. In this paper, we report a new type of dual-gate graphene ambipolar device with capability of operating under both common and differential modes to realize signal amplification. The signal goes through two stages of modulation where the phase of signal can be individually modulated to be either in-phase or out-of-phase at two stages by exploiting the ambipolarity of graphene. As a result, both common and differential mode amplifications can be achieved within one single device, which is not possible in the conventional circuit configuration. In addition, a common-mode rejection ratio as high as 80 dB can be achieved, making it possible for low noise circuit application. These results open up new directions of graphene-based ambipolar electronics that greatly simplify the RF circuit complexity and the design of multifunction device operation.

Energy Efficient Operation of Ammonia Refrigeration Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohammed, Abdul Qayyum; Wenning, Thomas J; Sever, Franc

Ammonia refrigeration systems typically offer many energy efficiency opportunities because of their size and complexity. This paper develops a model for simulating single-stage ammonia refrigeration systems, describes common energy saving opportunities, and uses the model to quantify those opportunities. The simulation model uses data that are typically available during site visits to ammonia refrigeration plants and can be calibrated to actual consumption and performance data if available. Annual electricity consumption for a base-case ammonia refrigeration system is simulated. The model is then used to quantify energy savings for six specific energy efficiency opportunities; reduce refrigeration load, increase suction pressure, employmore » dual suction, decrease minimum head pressure set-point, increase evaporative condenser capacity, and reclaim heat. Methods and considerations for achieving each saving opportunity are discussed. The model captures synergistic effects that result when more than one component or parameter is changed. This methodology represents an effective method to model and quantify common energy saving opportunities in ammonia refrigeration systems. The results indicate the range of savings that might be expected from common energy efficiency opportunities.« less

Global Strike 2035: Considerations for Enabling Effective Command and Control

DTIC Science & Technology

2012-02-16

reach places .1 Broadly grouped under the moniker Global Strike,2 this family-of-systems capability should mature by 2035 leading to the realization of...and] ‘micro-actors with massive impact,’…[combine] with new technology and new or transfigured ways of war, but the old threats also remain and have...as the Joint Time-Sensitive Targets Manager (JTSTM),38 “operators and analysts [could] access the same dynamic common operating picture…to provide

Function Package for Computing Quantum Resource Measures

NASA Astrophysics Data System (ADS)

Huang, Zhiming

2018-05-01

In this paper, we present a function package for to calculate quantum resource measures and dynamics of open systems. Our package includes common operators and operator lists, frequently-used functions for computing quantum entanglement, quantum correlation, quantum coherence, quantum Fisher information and dynamics in noisy environments. We briefly explain the functions of the package and illustrate how to use the package with several typical examples. We expect that this package is a useful tool for future research and education.

C2 of C3: Command and Control of Command, Control, Communication Systems.

DTIC Science & Technology

1988-04-22

capabilities the Army has not yet realized the full benefit of the new technology--largely because of deficiencies in the operational management of these newly...managers frequently constructed CEOI’s by drawing available frequencies or letter/number combinations (for unit callsigns) from a Bingo creel--which was...rapidly occurring changes, with subordinate units. At last, units were beginning to see the benefits of operating from a commonly shared data base. Up to

Technology Assessment of Avanced propulsion Systems for Some Classes of Combat Vehicles. Volume 3. Appendices G-M.

DTIC Science & Technology

1978-09-01

generally recognized that the best possible configura- tion for engines operating at high speeds and at high-pressure levels is probably the single...engines is invariably accom- plished by the operation of computer simulation models that generate specific numerical data rather than the generalized re...lationships common to other forms of prime mover based on units of mass or volume. Thus, providing such generalized relation- ships for a Stirling

75 FR 4560 - Ocean Transportation Intermediary License Applicants

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-28

... license as a Non-Vessel-Operating Common Carrier and Ocean Freight Forwarder--Ocean Transportation..., DC 20573. Non-Vessel-Operating Common Carrier--Ocean Transportation Intermediary Applicants: Doma... (Qualifying Individual), Rafia S. Waheed, President. Non-Vessel-Operating Common Carrier and Ocean Freight...

Resilient Grid Operational Strategies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pasqualini, Donatella

Extreme weather-related disturbances, such as hurricanes, are a leading cause of grid outages historically. Although physical asset hardening is perhaps the most common way to mitigate the impacts of severe weather, operational strategies may be deployed to limit the extent of societal and economic losses associated with weather-related physical damage.1 The purpose of this study is to examine bulk power-system operational strategies that can be deployed to mitigate the impact of severe weather disruptions caused by hurricanes, thereby increasing grid resilience to maintain continuity of critical infrastructure during extreme weather. To estimate the impacts of resilient grid operational strategies, Losmore » Alamos National Laboratory (LANL) developed a framework for hurricane probabilistic risk analysis (PRA). The probabilistic nature of this framework allows us to estimate the probability distribution of likely impacts, as opposed to the worst-case impacts. The project scope does not include strategies that are not operations related, such as transmission system hardening (e.g., undergrounding, transmission tower reinforcement and substation flood protection) and solutions in the distribution network.« less

Probability Distributions for Random Quantum Operations

NASA Astrophysics Data System (ADS)

Schultz, Kevin

Motivated by uncertainty quantification and inference of quantum information systems, in this work we draw connections between the notions of random quantum states and operations in quantum information with probability distributions commonly encountered in the field of orientation statistics. This approach identifies natural sample spaces and probability distributions upon these spaces that can be used in the analysis, simulation, and inference of quantum information systems. The theory of exponential families on Stiefel manifolds provides the appropriate generalization to the classical case. Furthermore, this viewpoint motivates a number of additional questions into the convex geometry of quantum operations relative to both the differential geometry of Stiefel manifolds as well as the information geometry of exponential families defined upon them. In particular, we draw on results from convex geometry to characterize which quantum operations can be represented as the average of a random quantum operation. This project was supported by the Intelligence Advanced Research Projects Activity via Department of Interior National Business Center Contract Number 2012-12050800010.

Survey of U.S. Ancillary Services Markets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Zhi; Levin, Todd; Conzelmann, Guenter

2016-01-01

In addition to providing energy to end-consumers, power system operators are also responsible for ensuring system reliability. To this end, power markets maintain an array of ancillary services to ensure it is always possible to balance the supply and demand for energy in real-time. A subset of these ancillary services are commonly procured through market-based mechanisms: namely, Regulation, Spinning, and Non-spinning Reserves.

Strengthening the management of ESA - the Inter-Directorate Reform of Corporate and Risk Management

NASA Astrophysics Data System (ADS)

Feustel-Büechl, Jörg; Arend, Harald; Derio, Eric; Infante, Giovanni; Kreiner, Gerhard; Phaler, Jesse; Tabbert, Michael

2007-02-01

ESA has undertaken the Inter-Directorate Reform of Corporate and Risk Management to strengthen the Agency's internal operations. The reform was completed at the end of 2006, encompassing five dedicated projects on Risk Management, Agency-Wide Controlling System, Project Plan and Integrated Project Review, General Budget Structure and Charging Policy, and Corporate Information Systems. It has contributed to improved management of the Agency's internal operations by engaging all internal stakeholders in a common objective, introducing improvements to planning and management methods, elaborating consolidated information structures and tools, contributing to enhanced transparency and accountability, and by providing qualified new policies, processes and tools.

The balloon and the airship technological heritage

NASA Technical Reports Server (NTRS)

Mayer, N. J.

1981-01-01

The balloon and the airship are discussed with emphasis on the identification of commonalities and distinctions. The aerostat technology behind the shape and structure of the vehicles is reviewed, including a discussion of structural weight, internal pressure, buckling, and the development of a stable tethered balloon system. Proper materials for the envelope are considered, taking elongation and stress into account, and flight operation and future developments are reviewed. Airships and tethered balloons which are designed to carry high operating pressure with low gas loss characteristics are found to share similar problems in low speed flight operations, while possessing interchangeable technologies.

Nickel release from surgical instruments and operating room equipment.

PubMed

Boyd, Anne H; Hylwa, Sara A

2018-04-15

Background There has been no systematic study assessing nickel release from surgical instruments and equipment used within the operating suite. This equipment represents important potential sources of exposure for nickel-sensitive patients and hospital staff. To investigate nickel release from commonly used surgical instruments and operating room equipment. Using the dimethylglyoxime nickel spot test, a variety of surgical instruments and operating room equipment were tested for nickel release at our institution. Of the 128 surgical instruments tested, only 1 was positive for nickel release. Of the 43 operating room items tested, 19 were positive for nickel release, 7 of which have the potential for direct contact with patients and/or hospital staff. Hospital systems should be aware of surgical instruments and operating room equipment as potential sources of nickel exposure.

Physician practice management companies: implications for hospital-based integrated delivery systems.

PubMed

Burns, L R; Robinson, J C

1997-01-01

Physician practice management companies (PPMCs) are one of the most visible entrants into the industry of managing physician practices, and anywhere from 100-150 are already in operation. Although PPMCs and hospital-based integrated delivery systems (IDSs) differ from each other in many ways, they share a number of common features, including the pursuit of capitation contracts from payors. As a result, PPMCs pose a growing, direct threat to hospital systems in competing for managed care contracts that cover physician service. PPMCs also provide an alternative to hospital-based IDSs at the local market level for physician group consolidation. This article looks at the structure, operation, and strategy of PPMCs and examines what implications their growth will have for hospital-based IDSs.

Experimenting with C2 Applications and Federated Infrastructures for Integrated Full-Spectrum Operational Environments in Support of Collaborative Planning and Interoperable Execution

DTIC Science & Technology

2004-06-01

Situation Understanding) Common Operational Pictures Planning & Decision Support Capabilities Message & Order Processing Common Operational...Pictures Planning & Decision Support Capabilities Message & Order Processing Common Languages & Data Models Modeling & Simulation Domain

Robotic acquisition programs: technical and performance challenges

NASA Astrophysics Data System (ADS)

Thibadoux, Steven A.

2002-07-01

The Unmanned Ground Vehicles/ Systems Joint Project Office (UGV/S JPO) is developing and fielding a variety of tactical robotic systems for the Army and Marine Corps. The Standardized Robotic System (SRS) provides a family of common components that can be installed in existing military vehicles, to allow unmanned operation of the vehicle and its payloads. The Robotic Combat Support System (RCSS) will be a medium sized unmanned system with interchangeable attachments, allowing a remote operator to perform a variety of engineering tasks. The Gladiator Program is a USMC initiative for a small to medium sized, highly mobile UGV to conduct scout/ surveillance missions and to carry various lethal and non-lethal payloads. Acquisition plans for these programs require preplanned evolutionary block upgrades to add operational capability, as new technology becomes available. This paper discusses technical and performance issues that must be resolved and the enabling technologies needed for near term block upgrades of these first generation robotic systems. Additionally, two Joint Robotics Program (JRP) initiatives, Robotic Acquisition through Virtual Environments and Networked Simulations (RAVENS) and Joint Architecture for Unmanned Ground Systems (JAUGS), will be discussed. RAVENS and JAUGS will be used to efficiently evaluate and integrate new technologies to be incorporated in system upgrades.

Multisensor interoperability for persistent surveillance and FOB protection with multiple technologies during the TNT exercise at Camp Roberts, California

NASA Astrophysics Data System (ADS)

Murarka, Naveen; Chambers, Jon

2012-06-01

Multiple sensors, providing actionable intelligence to the war fighter, often have difficulty interoperating with each other. Northrop Grumman (NG) is dedicated to solving these problems and providing complete solutions for persistent surveillance. In August, 2011, NG was invited to participate in the Tactical Network Topology (TNT) Capabilities Based Experimentation at Camp Roberts, CA to demonstrate integrated system capabilities providing Forward Operating Base (FOB) protection. This experiment was an opportunity to leverage previous efforts from NG's Rotorcraft Avionics Innovation Laboratory (RAIL) to integrate five prime systems with widely different capabilities. The five systems included a Hostile Fire and Missile Warning Sensor System, SCORPION II Unattended Ground Sensor system, Smart Integrated Vehicle Area Network (SiVAN), STARLite Synthetic Aperture Radar (SAR)/Ground Moving Target Indications (GMTI) radar system, and a vehicle with Target Location Module (TLM) and Laser Designation Module (LDM). These systems were integrated with each other and a Tactical Operations Center (TOC) equipped with RaptorX and Falconview providing a Common Operational Picture (COP) via Cursor on Target (CoT) messages. This paper will discuss this exercise, and the lessons learned, by integrating these five prime systems for persistent surveillance and FOB protection.

Research on numerical control system based on S3C2410 and MCX314AL

NASA Astrophysics Data System (ADS)

Ren, Qiang; Jiang, Tingbiao

2008-10-01

With the rapid development of micro-computer technology, embedded system, CNC technology and integrated circuits, numerical control system with powerful functions can be realized by several high-speed CPU chips and RISC (Reduced Instruction Set Computing) chips which have small size and strong stability. In addition, the real-time operating system also makes the attainment of embedded system possible. Developing the NC system based on embedded technology can overcome some shortcomings of common PC-based CNC system, such as the waste of resources, low control precision, low frequency and low integration. This paper discusses a hardware platform of ENC (Embedded Numerical Control) system based on embedded processor chip ARM (Advanced RISC Machines)-S3C2410 and DSP (Digital Signal Processor)-MCX314AL and introduces the process of developing ENC system software. Finally write the MCX314AL's driver under the embedded Linux operating system. The embedded Linux operating system can deal with multitask well moreover satisfy the real-time and reliability of movement control. NC system has the advantages of best using resources and compact system with embedded technology. It provides a wealth of functions and superior performance with a lower cost. It can be sure that ENC is the direction of the future development.

An alternative to sneakernet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orrell, S.; Ralstin, S.

1992-04-01

Many computer security plans specify that only a small percentage of the data processed will be classified. Thus, the bulk of the data on secure systems must be unclassified. Secure limited access sites operating approved classified computing systems sometimes also have a system ostensibly containing only unclassified files but operating within the secure environment. That system could be networked or otherwise connected to a classified system(s) in order that both be able to use common resources for file storage or computing power. Such a system must operate under the same rules as the secure classified systems. It is in themore » nature of unclassified files that they either came from, or will eventually migrate to, a non-secure system. Today, unclassified files are exported from systems within the secure environment typically by loading transport media and carrying them to an open system. Import of unclassified files is handled similarly. This media transport process, sometimes referred to as sneaker net, often is manually logged and controlled only by administrative procedures. A comprehensive system for secure bi-directional transfer of unclassified files between secure and open environments has yet to be developed. Any such secure file transport system should be required to meet several stringent criteria. It is the purpose of this document to begin a definition of these criteria.« less

An alternative to sneakernet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orrell, S.; Ralstin, S.

1992-01-01

Many computer security plans specify that only a small percentage of the data processed will be classified. Thus, the bulk of the data on secure systems must be unclassified. Secure limited access sites operating approved classified computing systems sometimes also have a system ostensibly containing only unclassified files but operating within the secure environment. That system could be networked or otherwise connected to a classified system(s) in order that both be able to use common resources for file storage or computing power. Such a system must operate under the same rules as the secure classified systems. It is in themore » nature of unclassified files that they either came from, or will eventually migrate to, a non-secure system. Today, unclassified files are exported from systems within the secure environment typically by loading transport media and carrying them to an open system. Import of unclassified files is handled similarly. This media transport process, sometimes referred to as sneaker net, often is manually logged and controlled only by administrative procedures. A comprehensive system for secure bi-directional transfer of unclassified files between secure and open environments has yet to be developed. Any such secure file transport system should be required to meet several stringent criteria. It is the purpose of this document to begin a definition of these criteria.« less

47 CFR 32.2682 - Leasehold improvements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS... telecommunications plant held under a capital or operating lease, which are subject to amortization treatment. This... telecommunications plant which are of a relatively minor cost or short life or for which the period of the lease is...

- Foreign Vessels « Coast Guard Maritime Commons

Science.gov Websites

demonstrated the highest commitment to maintaining strict compliance with U.S. and international safety international safety, security and environmental regulations. 11/22/2017: Notice of public meeting factors, it uncovered evidence of an ineffective safety management system within the operating company

47 CFR 32.2682 - Leasehold improvements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES UNIFORM SYSTEM OF ACCOUNTS... telecommunications plant held under a capital or operating lease, which are subject to amortization treatment. This... telecommunications plant which are of a relatively minor cost or short life or for which the period of the lease is...

Analysis, Modeling, and Simulation (AMS) testbed framework for Dynamic Mobility Applications (DMA) and Active Transportation and Demand Management (ATDM) programs.

DOT National Transportation Integrated Search

1997-08-01

A Regional ITS/CVO Coordination Plan outlines a strategy for the deployment of Intelligent Transportation Systems (ITS)/Commercial Vehicle Operations (CVO) technologies by a group of states with common economic and transportation needs. The Coordinat...

Co-simulation of heavy truck tire dynamics and electronic stability control systems (phase B).

DOT National Transportation Integrated Search

2010-07-01

In the past decade, electronic stability controls (ESC) have become increasingly common on vehicles operating in the United States. The acceptance of this technology has progressed to the point where all new passenger vehicles sold in the US are requ...

The embedded software life cycle - An expanded view

NASA Technical Reports Server (NTRS)

Larman, Brian T.; Loesh, Robert E.

1989-01-01

Six common issues that are encountered in the development of software for embedded computer systems are discussed from the perspective of their interrelationships with the development process and/or the system itself. Particular attention is given to concurrent hardware/software development, prototyping, the inaccessibility of the operational system, fault tolerance, the long life cycle, and inheritance. It is noted that the life cycle for embedded software must include elements beyond simply the specification and implementation of the target software.

Study to Expand Simulation Cockpit Displays of Advanced Sensors

DTIC Science & Technology

1981-03-01

common source is being used for multiple sensor types). If inde- pendent displays and controls are desired then two independent video sources or sensor...line is inserted in each gap, the result is the familiar 211 in- terlace. If two lines are inserted, the result is 31l interlace, and so on. The total...symbol generators. If these systems are oper- ating at various scan rates and if a common display device, such as a multifunction display (MFD) is to

Vaccum drainage system application in the management of operation-related non-regional epidural hematoma

PubMed Central

2013-01-01

Background Epidural intracranial hematoma is one of the most common complications of surgeries for intracranial tumors. The non-regional epidural hematoma is related to severe fluctuation of the intracranial pressure during the operation. The traditional management of hematoma evacuation through craniotomy is time-consuming and may aggravate intracranial pressure imbalance, which causes further complications. We designed a method using vaccum epidural drainage system, and tried to evaluate advantage and the disadvantage of this new technique. Methods Seven patients of intracranial tumors were selected. All of the patients received tumor resection and intra-operative non-regional epidural hematoma was confirmed through intra-operative ultrasound or CT scan. The vaccum drainage system was applied. Another ten patients who received craniotomy for intra-operative non-regional epidural hematoma evacuation were selected as comparison. Regular tests, like serial CT scan, were performed afterward to evaluate the effectiveness and to help deciding when to remove the drainage system. Results The vaccum drainage method was effective in epidual hemotoma clearance and prevented recurrent epidural hemorrhage. The drainage systems were removed within 4 days. All of the patients recovered well. No complications related to the drainage system were observed. Conclusions Compared to the traditional craniotomy, the new method of epidural hemoatoma management using vaccum epidural drainage system proved to be as effective in hematoma clearance, and was less-invasive and easier to perform, with less complication, shorter hospitalization, less economic burden, and better prognosis. PMID:23842198

An Introduction to Message-Bus Architectures for Space Systems

NASA Technical Reports Server (NTRS)

Smith, Danford; Gregory, Brian

2005-01-01

This course presents technical and programmatic information on the development of message-based architectures for space mission ground and flight software systems. Message-based architecture approaches provide many significant advantages over the more traditional socket-based one-of-a-kind integrated system development approaches. The course provides an overview of publish/subscribe concepts, the use of common isolation layer API's, approaches to message standardization, and other technical topics. Several examples of currently operational systems are discussed and possible changes to the system discussed and time for questions and answers will be provided.

Heat Pipe Space Nuclear Reactor Design Assessment. Volume 2. Feasibility Study of Upgrading the SP-100 Heat Pipe Space Nuclear Power System.

DTIC Science & Technology

1985-08-01

system thermal -to-electric energy conversion efficiency quite high (-20-25 percent). c. Fuel system--Figure 6 compares the fuel swelling of U02 , UN... high temperature reservoir. Figure 28 shows a schematic of an AMTEC operation. The efficiency of ANTEC is calculated by: IV IV + 1 (L + C AT) + Qloss... thermal energy to electrical energy. The high efficiency and low specific mass (for large systems) are the common advantages of these active systems. In

[Analysis of microbial flora during operation for cholangitis and other inflammatory deseases of the hepato-billiary system].

PubMed

Zhivkov, E; Dimitrova, V; Popov, V; Tosheva, E; Taneva, I

2006-01-01

Inflammatory deseases of the billiary system are common in the hepato-billiary surgery. Most serious is the cholangitis. Treatment is based on individual approach of choice of moment of correct surgical intervention and corresponding adequate antibiotic therapy. Retrospective analysis of the experience of our clinic of the positive biliocultures and their antibiograms. 152 positive biliocultures taken intraoperativly, for 10 years period. 48 of them are from patients with cholangitis. Analysis of count and species microbiological agents and their sensitivity to antibiogram antibiotics in table format. The data of the literature reviewed and discussed. Most common microbiological agents are E. coli 60%, Klebsiella 31%, Pseudomonas 24%. In 40% theres are more then one agent. Most common agents have big sensivity to Cefalosporines II-III generation, Amikacin, Ciprofloxacin and Carbapenems.

Open Architecture Standard for NASA's Software-Defined Space Telecommunications Radio Systems

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Johnson, Sandra K.; Kacpura, Thomas J.; Hall, Charles S.; Smith, Carl R.; Liebetreu, John

2008-01-01

NASA is developing an architecture standard for software-defined radios used in space- and ground-based platforms to enable commonality among radio developments to enhance capability and services while reducing mission and programmatic risk. Transceivers (or transponders) with functionality primarily defined in software (e.g., firmware) have the ability to change their functional behavior through software alone. This radio architecture standard offers value by employing common waveform software interfaces, method of instantiation, operation, and testing among different compliant hardware and software products. These common interfaces within the architecture abstract application software from the underlying hardware to enable technology insertion independently at either the software or hardware layer. This paper presents the initial Space Telecommunications Radio System (STRS) Architecture for NASA missions to provide the desired software abstraction and flexibility while minimizing the resources necessary to support the architecture.

Prototype Tool and Focus Group Evaluation for an Advanced Trajectory-Based Operations Concept

NASA Technical Reports Server (NTRS)

Guerreiro, Nelson M.; Jones, Denise R.; Barmore, Bryan E.; Butler, Ricky W.; Hagen, George E.; Maddalon, Jeffrey M.; Ahmad, Nash'at N.

2017-01-01

Trajectory-based operations (TBO) is a key concept in the Next Generation Air Transportation System transformation of the National Airspace System (NAS) that will increase the predictability and stability of traffic flows, support a common operational picture through the use of digital data sharing, facilitate more effective collaborative decision making between airspace users and air navigation service providers, and enable increased levels of integrated automation across the NAS. NASA has been developing trajectory-based systems to improve the efficiency of the NAS during specific phases of flight and is now also exploring Advanced 4-Dimensional Trajectory (4DT) operational concepts that will integrate these technologies and incorporate new technology where needed to create both automation and procedures to support gate-to-gate TBO. A TBO Prototype simulation toolkit has been developed that demonstrates initial functionality of an Advanced 4DT TBO concept. Pilot and controller subject matter experts (SMEs) were brought to the Air Traffic Operations Laboratory at NASA Langley Research Center for discussions on an Advanced 4DT operational concept and were provided an interactive demonstration of the TBO Prototype using four example scenarios. The SMEs provided feedback on potential operational, technological, and procedural opportunities and concerns. This paper describes an Advanced 4DT operational concept, the TBO Prototype, the demonstration scenarios and methods used, and the feedback obtained from the pilot and controller SMEs in this focus group activity.

Overview of condition monitoring and operation control of electric power conversion systems in direct-drive wind turbines under faults

NASA Astrophysics Data System (ADS)

Huang, Shoudao; Wu, Xuan; Liu, Xiao; Gao, Jian; He, Yunze

2017-09-01

Electric power conversion system (EPCS), which consists of a generator and power converter, is one of the most important subsystems in a direct-drive wind turbine (DD-WT). However, this component accounts for the most failures (approximately 60% of the total number) in the entire DD-WT system according to statistical data. To improve the reliability of EPCSs and reduce the operation and maintenance cost of DD-WTs, numerous researchers have studied condition monitoring (CM) and fault diagnostics (FD). Numerous CM and FD techniques, which have respective advantages and disadvantages, have emerged. This paper provides an overview of the CM, FD, and operation control of EPCSs in DD-WTs under faults. After introducing the functional principle and structure of EPCS, this survey discusses the common failures in wind generators and power converters; briefly reviewed CM and FD methods and operation control of these generators and power converters under faults; and discussed the grid voltage faults related to EPCSs in DD-WTs. These theories and their related technical concepts are systematically discussed. Finally, predicted development trends are presented. The paper provides a valuable reference for developing service quality evaluation methods and fault operation control systems to achieve high-performance and high-intelligence DD-WTs.

BIOFILTRATION OF VOLATILE POLLUTANTS: Fundamental Mechanisms for Improved Design, Long-term Operation, Prediction, and Implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison,Brian H.

2000-12-31

Biofiltration systems can be used for treatment of volatile organic compounds (VOCs); however, the systems are poorly understood and are normally operated as ''black boxes''. Common operational problems associated with biofilters include fouling, deactivation, and overgrowth, all of which make them ineffective for continuous, long-term use. The objective of this investigation was to develop generic methods for long-term stable operation, in particular by using selective limitation of supplemental nutrients while maintaining high activity. As part of this effort, we have provided a deeper fundamental understanding of the important biological and transport mechanisms in biodestruction of sparingly soluble VOCs and havemore » extended this approach and mathematical models to additional systems of high priority EM relevance--direct degradation and cometabolic degradation of priority pollutants such as BTEX and chlorinated organics. Innovative aspects of this project included development of a user-friendly two-dimensional predictive model/program for MS Windows 95/98/2000 to elucidate mass transfer and kinetic limitations in these systems, isolation of a unique microorganism capable of using sparingly soluble organic and chloroorganic VOCs as its sole carbon and energy source, and making long-term growth possible by successfully decoupling growth and degradation metabolisms in operating trickle bed bioreactors.« less

Magnetic suspension and balance system study

NASA Technical Reports Server (NTRS)

Boom, R. W.; Eyssa, Y. M.; Mcintosh, G. E.; Abdelsalam, M. K.

1984-01-01

A compact design for a superconducting magnetic suspension and balance system is developed for a 8 ft. x 8 ft. transonic wind tunnel. The main features of the design are: a compact superconducting solenoid in the suspended airplane model; permanent magnet wings; one common liquid helium dewar for all superconducting coils; efficient new race track coils for roll torques; use of established 11 kA cryostable AC conductor; acceptable AC losses during 10 Hz control even with all steel structure; and a 560 liter/hour helium liquefier. Considerable design simplicity, reduced magnet weights, and reduced heat leak results from using one common dewar which eliminates most heavy steel structure between coils and the suspended model. Operational availability is thought to approach 100% for such magnet systems. The weight and cost of the magnet system is approximately one-third that of previous less compact designs.

Analysis of mental workload of electrical power plant operators of control and operation centers.

PubMed

Vitório, Daiana Martins; Masculo, Francisco Soares; Melo, Miguel O B C

2012-01-01

Electrical systems can be categorized as critical systems where failure can result in significant financial loss, injury or threats to human life. The operators of the electric power control centers perform an activity in a specialized environment and have to carry it out by mobilizing knowledge and reasoning to which they have adequate training under the terms of the existing rules. To reach this there is a common mental request of personnel involved in these centers due the need to maintain attention, memory and reasoning request. In this sense, this study aims to evaluate the Mental Workload of technical workers of the Control Centers of Electrical Energy. It was undertaken a research on operators control centers of the electricity sector in Northeast Brazil. It was used for systematic observations, followed by interview and application of the instrument National Aeronautics and Space Administration Task Load Index known as NASA-TLX. As a result there will be subsidies for an assessment of mental workload of operators, and a contribution to improving the processes of managing the operation of electric utilities and the quality of workers.

Joint Polar Satellite System (JPSS) Common Ground System (CGS) Block 3.0 Communications Strategies

NASA Astrophysics Data System (ADS)

Miller, S. W.; Grant, K. D.; Ottinger, K.

2015-12-01

The National Oceanic and Atmospheric Administration (NOAA) and National Aeronautics and Space Administration (NASA) are jointly acquiring the next-generation civilian weather and environmental satellite system: the Joint Polar Satellite System (JPSS). The JPSS program is the follow-on for both space and ground systems to the Polar-orbiting Operational Environmental Satellites (POES) managed by NOAA. The JPSS satellites will carry a suite of sensors designed to collect meteorological, oceanographic, climatological and geophysical observations of the Earth. The ground processing system for JPSS is known as the JPSS Common Ground System (JPSS CGS). Developed and maintained by Raytheon Intelligence, Information and Services (IIS), the CGS is a globally distributed, multi-mission system serving NOAA, NASA and their national and international partners. The CGS has demonstrated its scalability and flexibility to incorporate multiple missions efficiently and with minimal cost, schedule and risk, while strengthening global partnerships in weather and environmental monitoring. In a highly successful international partnership between NOAA and the European Organisation for the Exploitation of Meteorological Satellites (EUMETSAT), the CGS currently provides data routing from McMurdo Station in Antarctica to the EUMETSAT processing center in Darmstadt, Germany. Continuing and building upon that partnership, NOAA and EUMETSAT are collaborating on the development of a new path forward for the 2020's. One approach being explored is a concept of operations where each organization shares satellite downlink resources with the other. This paper will describe that approach, as well as modeling results that demonstrate its feasibility and expected performance.

46 CFR 520.11 - Non-vessel-operating common carriers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 9 2010-10-01 2010-10-01 false Non-vessel-operating common carriers. 520.11 Section 520.11 Shipping FEDERAL MARITIME COMMISSION REGULATIONS AFFECTING OCEAN SHIPPING IN FOREIGN COMMERCE CARRIER AUTOMATED TARIFFS § 520.11 Non-vessel-operating common carriers. (a) Financial responsibility. An...

Continuously-stirred anaerobic digester to convert organic wastes into biogas: system setup and basic operation.

PubMed

Usack, Joseph G; Spirito, Catherine M; Angenent, Largus T

2012-07-13

Anaerobic digestion (AD) is a bioprocess that is commonly used to convert complex organic wastes into a useful biogas with methane as the energy carrier. Increasingly, AD is being used in industrial, agricultural, and municipal waste(water) treatment applications. The use of AD technology allows plant operators to reduce waste disposal costs and offset energy utility expenses. In addition to treating organic wastes, energy crops are being converted into the energy carrier methane. As the application of AD technology broadens for the treatment of new substrates and co-substrate mixtures, so does the demand for a reliable testing methodology at the pilot- and laboratory-scale. Anaerobic digestion systems have a variety of configurations, including the continuously stirred tank reactor (CSTR), plug flow (PF), and anaerobic sequencing batch reactor (ASBR) configurations. The CSTR is frequently used in research due to its simplicity in design and operation, but also for its advantages in experimentation. Compared to other configurations, the CSTR provides greater uniformity of system parameters, such as temperature, mixing, chemical concentration, and substrate concentration. Ultimately, when designing a full-scale reactor, the optimum reactor configuration will depend on the character of a given substrate among many other nontechnical considerations. However, all configurations share fundamental design features and operating parameters that render the CSTR appropriate for most preliminary assessments. If researchers and engineers use an influent stream with relatively high concentrations of solids, then lab-scale bioreactor configurations cannot be fed continuously due to plugging problems of lab-scale pumps with solids or settling of solids in tubing. For that scenario with continuous mixing requirements, lab-scale bioreactors are fed periodically and we refer to such configurations as continuously stirred anaerobic digesters (CSADs). This article presents a general methodology for constructing, inoculating, operating, and monitoring a CSAD system for the purpose of testing the suitability of a given organic substrate for long-term anaerobic digestion. The construction section of this article will cover building the lab-scale reactor system. The inoculation section will explain how to create an anaerobic environment suitable for seeding with an active methanogenic inoculum. The operating section will cover operation, maintenance, and troubleshooting. The monitoring section will introduce testing protocols using standard analyses. The use of these measures is necessary for reliable experimental assessments of substrate suitability for AD. This protocol should provide greater protection against a common mistake made in AD studies, which is to conclude that reactor failure was caused by the substrate in use, when really it was improper user operation.

A physical layer perspective on access network sharing

NASA Astrophysics Data System (ADS)

Pfeiffer, Thomas

2015-12-01

Unlike in copper or wireless networks, there is no sharing of resources in fiber access networks yet, other than bit stream access or cable sharing, in which the fibers of a cable are let to one or multiple operators. Sharing optical resources on a single fiber among multiple operators or different services has not yet been applied. While this would allow for a better exploitation of installed infrastructures, there are operational issues which still need to be resolved, before this sharing model can be implemented in networks. Operating multiple optical systems and services over a common fiber plant, autonomously and independently from each other, can result in mutual distortions on the physical layer. These distortions will degrade the performance of the involved systems, unless precautions are taken in the infrastructure hardware to eliminate or to reduce them to an acceptable level. Moreover, the infrastructure needs to be designed such as to support different system technologies and to ensure a guaranteed quality of the end-to-end connections. In this paper, suitable means are proposed to be introduced in fiber access infrastructures that will allow for shared utilization of the fibers while safeguarding the operational needs and business interests of the involved parties.

Augmented reality user interface for mobile ground robots with manipulator arms

NASA Astrophysics Data System (ADS)

Vozar, Steven; Tilbury, Dawn M.

2011-01-01

Augmented Reality (AR) is a technology in which real-world visual data is combined with an overlay of computer graphics, enhancing the original feed. AR is an attractive tool for teleoperated UGV UIs as it can improve communication between robots and users via an intuitive spatial and visual dialogue, thereby increasing operator situational awareness. The successful operation of UGVs often relies upon both chassis navigation and manipulator arm control, and since existing literature usually focuses on one task or the other, there is a gap in mobile robot UIs that take advantage of AR for both applications. This work describes the development and analysis of an AR UI system for a UGV with an attached manipulator arm. The system supplements a video feed shown to an operator with information about geometric relationships within the robot task space to improve the operator's situational awareness. Previous studies on AR systems and preliminary analyses indicate that such an implementation of AR for a mobile robot with a manipulator arm is anticipated to improve operator performance. A full user-study can determine if this hypothesis is supported by performing an analysis of variance on common test metrics associated with UGV teleoperation.

Incorporation of quality updates for JPSS CGS Products

NASA Astrophysics Data System (ADS)

Cochran, S.; Grant, K. D.; Ibrahim, W.; Brueske, K. F.; Smit, P.

2016-12-01

NOAA's next-generation environmental satellite, the Joint Polar Satellite System (JPSS) replaces the current Polar-orbiting Operational Environmental Satellites (POES). JPSS satellites carry sensors which collect meteorological, oceanographic, climatological, and solar-geophysical observations of the earth, atmosphere, and space. The first JPSS satellite was launched in 2011 and is currently NOAA's primary operational polar satellite. The JPSS ground system is the Common Ground System (CGS), and provides command, control, and communications (C3) and data processing (DP). A multi-mission system, CGS provides combinations of C3/DP for numerous NASA, NOAA, DoD, and international missions. In preparation for the next JPSS satellite, CGS improved its multi-mission capabilities to enhance mission operations for larger constellations of earth observing satellites with the added benefit of streamlining mission operations for other NOAA missions. This paper will discuss both the theoretical basis and the actual practices used to date to identify, test and incorporate algorithm updates into the CGS processing baseline. To provide a basis for this support, Raytheon developed a theoretical analysis framework, and the application of derived engineering processes, for the maintenance of consistency and integrity of remote sensing operational algorithm outputs. The framework is an abstraction of the operationalization of the science-grade algorithm (Sci2Ops) process used throughout the JPSS program. By combining software and systems engineering controls, manufacturing disciplines to detect and reduce defects, and a standard process to control analysis, an environment to maintain operational algorithm maturity is achieved. Results of the use of this approach to implement algorithm changes into operations will also be detailed.

Methods and Tools for Product Quality Maintenance in JPSS CGS

NASA Astrophysics Data System (ADS)

Cochran, S.; Smit, P.; Grant, K. D.; Jamilkowski, M. L.

2015-12-01

NOAA's next-generation environmental satellite, the Joint Polar Satellite System (JPSS) replaces the current Polar-orbiting Operational Environmental Satellites (POES). JPSS satellites carry sensors which collect meteorological, oceanographic, climatological, and solar-geophysical observations of the earth, atmosphere, and space. The first JPSS satellite was launched in 2011 and is currently NOAA's primary operational polar satellite. The JPSS ground system is the Common Ground System (CGS), and provides command, control, and communications (C3) and data processing (DP). A multi-mission system, CGS provides combinations of C3/DP for numerous NASA, NOAA, DoD, and international missions. In preparation for the next JPSS satellite, CGS improved its multi-mission capabilities to enhance mission operations for larger constellations of earth observing satellites with the added benefit of streamlining mission operations for other NOAA missions. This paper will discuss both the theoretical basis and the actual practices used to date to identify, test and incorporate algorithm updates into the CGS processing baseline. To provide a basis for this support, Raytheon developed a theoretical analysis framework, and the application of derived engineering processes, for the maintenance of consistency and integrity of remote sensing operational algorithm outputs. The framework is an abstraction of the operationalization of the science-grade algorithm (Sci2Ops) process used throughout the JPSS program. By combining software and systems engineering controls, manufacturing disciplines to detect and reduce defects, and a standard process to control analysis, an environment to maintain operational algorithm maturity is achieved. Results of the use of this approach to implement algorithm changes into operations will also be detailed.

Distributed intelligence for supervisory control

NASA Technical Reports Server (NTRS)

Wolfe, W. J.; Raney, S. D.

1987-01-01

Supervisory control systems must deal with various types of intelligence distributed throughout the layers of control. Typical layers are real-time servo control, off-line planning and reasoning subsystems and finally, the human operator. Design methodologies must account for the fact that the majority of the intelligence will reside with the human operator. Hierarchical decompositions and feedback loops as conceptual building blocks that provide a common ground for man-machine interaction are discussed. Examples of types of parallelism and parallel implementation on several classes of computer architecture are also discussed.

Human Behaviour in High Stress Situations in Aerospace Operations Conference Proceedings Held in The Hague, The Netherlands on 24-28 October 1988

DTIC Science & Technology

1989-06-01

Continuously stimulating advances in the aerospace sciences relevant to strengthening the common defence posture; - Improving the co-operation among member...very stimulating symposium. vii KI-1 PREDICTION OF PERSONALITY Harald T. Andersen M.D., Ph.D., D.Sc,D.Av.Med. Director RNoAF Institute of Aviation...audio tape recorder which was connected to the aircraft communication system. This recorder provided a continuous auditory record of each mission so that

Implementing the Common Core of Constructs: Measurement and Interviewer Training. The Project on State-Level Child Outcomes. Proceedings of the Meeting of the Operational Phase of the Project on State-Level Child Outcome (1st, Washington, DC, December 9, 1997).

ERIC Educational Resources Information Center

Child Trends, Inc., Washington, DC.

The Project on State-Level Child Outcomes is designed to assist states and other groups to improve the measurement of child outcomes in state welfare evaluations and in other state data systems. This report summarizes the first meeting of the five states (Connecticut, Florida, Indiana, Iowa, Minnesota) that participated in the operational phase of…

Can varying the number of teams in a shift schedule constitute a preventive strategy?

PubMed

Jeppesen, Hans Jeppe; Kleiven, Magnar; Bøggild, Henrik

2004-12-01

The study examines the implications for shiftworkers of applying different numbers of teams in the organization of shiftwork. The participating operators came from five different companies applying continuous shift rotation systems. The companies shared the same product organization and a common corporate culture belonging to the same multinational company. Each company had a shift system consisting of four, five or six teams, with the proportion of shifts outside day work decreasing as the number of teams increased. Questionnaire and documentary data were used as data sources. Operators in systems with additional teams had more daywork but also more irregular working hours due to both overtime and schedule changes. Operators using six teams used fewer social compensation strategies. Operators in four teams were most satisfied with their work hours. Satisfaction with the time available for various social activities outside work varied inconsistently between the groups. In rotating systems the application of more teams reduces the number of shifts outside day work. This apparent improvement for shiftworkers was counteracted by a concomitant irregularity produced by greater organizational requirements for flexibility. The balance of this interaction was found to have a critical impact on employees.

Low-Noise Band-Pass Amplifier

NASA Technical Reports Server (NTRS)

Kleinberg, L.

1982-01-01

Circuit uses standard components to overcome common limitation of JFET amplifiers. Low-noise band-pass amplifier employs JFET and operational amplifier. High gain and band-pass characteristics are achieved with suitable choice of resistances and capacitances. Circuit should find use as low-noise amplifier, for example as first stage instrumentation systems.

47 CFR 32.7300 - Nonoperating income and expense.

Code of Federal Regulations, 2011 CFR

2011-10-01

... investments in common and preferred stock, which is the property of the company, whether such stock is owned... UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions For Other Income Accounts § 32..., events and circumstances affecting the company during a period and which are not operational in nature...

Building a model-based decision support system for solving vehicle routing and driver scheduling problems under hours of service regulations.

DOT National Transportation Integrated Search

2011-08-27

"In principle, hours-of-service (HOS) regulations are intended to help truck drivers ensure get adequate rest and perform safe operations. The new HOS regulations, however, may lead to substantial cost increases for regional common carriers which hav...

Integrated imaging sensor systems with CMOS active pixel sensor technology

NASA Technical Reports Server (NTRS)

Yang, G.; Cunningham, T.; Ortiz, M.; Heynssens, J.; Sun, C.; Hancock, B.; Seshadri, S.; Wrigley, C.; McCarty, K.; Pain, B.

2002-01-01

This paper discusses common approaches to CMOS APS technology, as well as specific results on the five-wire programmable digital camera-on-a-chip developed at JPL. The paper also reports recent research in the design, operation, and performance of APS imagers for several imager applications.

Settleometer. Operational Control Tests for Wastewater Treatment Facilities. Instructor's Manual [and] Student Workbook.

ERIC Educational Resources Information Center

Arasmith, E. E.

The settleometer test is used to indicate the solids-liquid separation (downtime) capability of sludge, most commonly on activated sludge entering the secondary clarifier and aerobic digesters. Designed for individuals who have completed National Pollutant Discharge Elimination System (NPDES) level 1 laboratory training skills, this module…

Applying Hierarchical Model Calibration to Automatically Generated Items.

ERIC Educational Resources Information Center

Williamson, David M.; Johnson, Matthew S.; Sinharay, Sandip; Bejar, Isaac I.

This study explored the application of hierarchical model calibration as a means of reducing, if not eliminating, the need for pretesting of automatically generated items from a common item model prior to operational use. Ultimately the successful development of automatic item generation (AIG) systems capable of producing items with highly similar…

Foster Youth Who Have Succeeded in Higher Education: Common Themes

ERIC Educational Resources Information Center

Lovitt, Thomas; Emerson, John

2009-01-01

All young people, including foster youth and youth with disabilities, can succeed academically given adequate support and advocacy from educators, professionals, and their caregivers. Casey Family Programs (www.casey.org), a Seattle-based national operating foundation that has served children, youth, and families in the child welfare system since…

Digital Libraries--Methods and Applications

ERIC Educational Resources Information Center

Huang, Kuo Hung, Ed.

2011-01-01

Digital library is commonly seen as a type of information retrieval system which stores and accesses digital content remotely via computer networks. However, the vision of digital libraries is not limited to technology or management, but user experience. This book is an attempt to share the practical experiences of solutions to the operation of…

S.M.P. SEQUENTIAL MATHEMATICS PROGRAM.

ERIC Educational Resources Information Center

CICIARELLI, V; LEONARD, JOSEPH

A SEQUENTIAL MATHEMATICS PROGRAM BEGINNING WITH THE BASIC FUNDAMENTALS ON THE FOURTH GRADE LEVEL IS PRESENTED. INCLUDED ARE AN UNDERSTANDING OF OUR NUMBER SYSTEM, AND THE BASIC OPERATIONS OF WORKING WITH WHOLE NUMBERS--ADDITION, SUBTRACTION, MULTIPLICATION, AND DIVISION. COMMON FRACTIONS ARE TAUGHT IN THE FIFTH, SIXTH, AND SEVENTH GRADES. A…

14 CFR 171.105 - Minimum requirements for approval.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the frequency channel is needed for higher priority common system service. ... agree to operate and maintain the facility in accordance with § 171.115. (5) The owner must agree to furnish periodic reports as set forth in § 171.117, and agree to allow the FAA to inspect the facility and...

Space Telecommunications Radio System (STRS) Architecture Standard. Release 1.02.1

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Kacpura, Thomas J.; Handler, Louis M.; Hall, C. Steve; Mortensen, Dale J.; Johnson, Sandra K.; Briones, Janette C.; Nappier, Jennifer M.; Downey, Joseph A.; Lux, James P.

2012-01-01

This document contains the NASA architecture standard for software defined radios used in space- and ground-based platforms to enable commonality among radio developments to enhance capability and services while reducing mission and programmatic risk. Transceivers (or transponders) with functionality primarily defined in software (e.g., firmware) have the ability to change their functional behavior through software alone. This radio architecture standard offers value by employing common waveform software interfaces, method of instantiation, operation, and testing among different compliant hardware and software products. These common interfaces within the architecture abstract application software from the underlying hardware to enable technology insertion independently at either the software or hardware layer.

ISRU Reactant, Fuel Cell Based Power Plant for Robotic and Human Mobile Exploration Applications

NASA Technical Reports Server (NTRS)

Baird, Russell S.; Sanders, Gerald; Simon, Thomas; McCurdy, Kerri

2003-01-01

Three basic power generation system concepts are generally considered for lander, rover, and Extra-Vehicular Activity (EVA) assistant applications for robotic and human Moon and Mars exploration missions. The most common power system considered is the solar array and battery system. While relatively simple and successful, solar array/battery systems have some serious limitations for mobile applications. For typical rover applications, these limitations include relatively low total energy storage capabilities, daylight only operating times (6 to 8 hours on Mars), relatively short operating lives depending on the operating environment, and rover/lander size and surface use constraints. Radioisotope power systems are being reconsidered for long-range science missions. Unfortunately, the high cost, political controversy, and launch difficulties that are associated with nuclear-based power systems suggests that the use of radioisotope powered landers, rovers, and EVA assistants will be limited. The third power system concept now being considered are fuel cell based systems. Fuel cell power systems overcome many of the performance and surface exploration limitations of solar array/battery power systems and the prohibitive cost and other difficulties associated with nuclear power systems for mobile applications. In an effort to better understand the capabilities and limitations of fuel cell power systems for Moon and Mars exploration applications, NASA is investigating the use of in-Situ Resource Utilization (ISRU) produced reactant, fuel cell based power plants to power robotic outpost rovers, science equipment, and future human spacecraft, surface-excursion rovers, and EVA assistant rovers. This paper will briefly compare the capabilities and limitations of fuel cell power systems relative to solar array/battery and nuclear systems, discuss the unique and enhanced missions that fuel cell power systems enable, and discuss the common technology and system attributes possible for robotic and human exploration to maximize scientific return and minimize cost and risk to both. Progress made to date at the Johnson Space Center on an ISRU producible reactant, Proton Exchange Membrane (PEM) fuel cell based power plant project to demonstrate the concept in conjunction with rover applications will be presented in detail.

ISRU Reactant, Fuel Cell Based Power Plant for Robotic and Human Mobile Exploration Applications

NASA Astrophysics Data System (ADS)

Baird, Russell S.; Sanders, Gerald; Simon, Thomas; McCurdy, Kerri

2003-01-01

Three basic power generation system concepts are generally considered for lander, rover, and Extra-Vehicular Activity (EVA) assistant applications for robotic and human Moon and Mars exploration missions. The most common power system considered is the solar array and battery system. While relatively simple and successful, solar array/battery systems have some serious limitations for mobile applications. For typical rover applications, these limitations include relatively low total energy storage capabilities, daylight only operating times (6 to 8 hours on Mars), relatively short operating lives depending on the operating environment, and rover/lander size and surface use constraints. Radioisotope power systems are being reconsidered for long-range science missions. Unfortunately, the high cost, political controversy, and launch difficulties that are associated with nuclear-based power systems suggests that the use of radioisotope powered landers, rovers, and EVA assistants will be limited. The third power system concept now being considered are fuel cell based systems. Fuel cell power systems overcome many of the performance and surface exploration limitations of solar array/battery power systems and the prohibitive cost and other difficulties associated with nuclear power systems for mobile applications. In an effort to better understand the capabilities and limitations of fuel cell power systems for Moon and Mars exploration applications. NASA is investigating the use of In-Situ Resource Utilization (ISRU) produced reactant, fuel cell based power plants to power robotic outpost rovers, science equipment, and future human spacecraft, surface-excursion rovers, and EVA assistant rovers. This paper will briefly compare the capabilities and limitations of fuel cell power systems relative to solar array/battery and nuclear systems, discuss the unique and enhanced missions that fuel cell power systems enable, and discuss the common technology and system attributes possible for robotic and human exploration to maximize scientific return and minimize cost and risk to both. Progress made to date at the Johnson Space Center on an ISRU producible reactant. Proton Exchange Membrane (PEM) fuel cell based power plant project for use in the first demonstration of this concept in conjunction with rover applications will be presented in detail.

A Model of Workflow Composition for Emergency Management

NASA Astrophysics Data System (ADS)

Xin, Chen; Bin-ge, Cui; Feng, Zhang; Xue-hui, Xu; Shan-shan, Fu

The common-used workflow technology is not flexible enough in dealing with concurrent emergency situations. The paper proposes a novel model for defining emergency plans, in which workflow segments appear as a constituent part. A formal abstraction, which contains four operations, is defined to compose workflow segments under constraint rule. The software system of the business process resources construction and composition is implemented and integrated into Emergency Plan Management Application System.

Reducing Stator Current Harmonics for a Doubly-Fed Induction Generator Connected to a Distorted Grid

DTIC Science & Technology

2013-09-01

electric grid voltage harmonics, which is a potential obstacle for implementing stable wind -energy systems. Two existing rotor voltage controllers...electric grid voltage harmonics, which is a potential obstacle for implementing stable wind -energy systems. Two existing rotor voltage controllers...speed of the DFIG can be adjusted to optimize turbine efficiency for given wind conditions. A common method for controlling the operating speed is

A Common Interface Real-Time Multiprocessor Operating System for Embedded Systems

DTIC Science & Technology

1991-03-04

Pressman , a design methodology should show hierarchical organization, lead to modules exhibiting independent functional characteristics, and be derived...Boehm, Barry W. "Software Engineering," Tutorial: Software Design Strategies, 2nd Edition. 35-50. Los Angeles CA: IEEE Computer Society Press, 1981... Pressman , Roger S. Software Engineering: A Practitioner’s Approach, Second Edi- tion. McGraw-Hill Book Company, New York, 1988. 59. Quinn, Michael J

Software Requirements Engineering Methodology

DTIC Science & Technology

1976-09-01

common speech, so that the specification can be read by managers, systems enginetrs, and others who are not specially trained in the language. To...of the system and its DPS. They are usually implicit in the wording of the originating specifications, although the new SREM user must train ...to the name of the ENTITYjCLASS, the operation is applicable only to a single instance. This concentration of the requirements for creation and

Reliability Engineering for Service Oriented Architectures

DTIC Science & Technology

2013-02-01

Common Object Request Broker Architecture Ecosystem In software , an ecosystem is a set of applications and/or services that grad- ually build up over time...Enterprise Service Bus Foreign In an SOA context: Any SOA, service or software which the owners of the calling software do not have control of, either...SOA Service Oriented Architecture SRE Software Reliability Engineering System Mode Many systems exhibit different modes of operation. E.g. the cockpit

The Development of Educational Environment Suited to the Japan-Specific Educational Service Using Requirements Engineering Techniques: Case Study of Running Sakai with PostgreSQL

ERIC Educational Resources Information Center

Terawaki, Yuki; Takahashi, Yuichi; Kodama, Yasushi; Yana, Kazuo

2011-01-01

This paper describes an integration of different Relational Database Management System (RDBMS) of two Course Management Systems (CMS) called Sakai and the Common Factory for Inspiration and Value in Education (CFIVE). First, when the service of CMS is provided campus-wide, the problems of user support, CMS operation and customization of CMS are…

Riemann sum method for non-line-of-sight ultraviolet communication in noncoplanar geometry

NASA Astrophysics Data System (ADS)

Song, Peng; Zhou, Xianli; Song, Fei; Zhao, Taifei; Li, Yunhong

2017-12-01

The non-line-of-sight ultraviolet (UV) communication relies on the scattering common volume, however, it is difficult to carry out the triple integral operation of the scattering common volume. Based on UV single-scattering propagation theory and the spherical coordinate, we propose to use the Riemann sum method (RSM) to analyze the link path loss (PL) of UV communication system in noncoplanar geometries, and carried out related simulations. In addition, an outdoor testbed using UV light-emitting diode was set up to provide support for the validity of the RSM. When the elevation angles of the transmitter or the receiver are small, using RSM, the channel PL and temporal response of UV communication systems can be effectively and efficiently calculated. It is useful in UV embedded system design.

Arrester Resistive Current Measuring System Based on Heterogeneous Network

NASA Astrophysics Data System (ADS)

Zhang, Yun Hua; Li, Zai Lin; Yuan, Feng; Hou Pan, Feng; Guo, Zhan Nan; Han, Yue

2018-03-01

Metal Oxide Arrester (MOA) suffers from aging and poor insulation due to long-term impulse voltage and environmental impact, and the value and variation tendency of resistive current can reflect the health conditions of MOA. The common wired MOA detection need to use long cables, which is complicated to operate, and that wireless measurement methods are facing the problems of poor data synchronization and instability. Therefore a novel synchronous measurement system of arrester current resistive based on heterogeneous network is proposed, which simplifies the calculation process and improves synchronization, accuracy and stability and of the measuring system. This system combines LoRa wireless network, high speed wireless personal area network and the process layer communication, and realizes the detection of arrester working condition. Field test data shows that the system has the characteristics of high accuracy, strong anti-interference ability and good synchronization, which plays an important role in ensuring the stable operation of the power grid.

Large-scale modular biofiltration system for effective odor removal in a composting facility.

PubMed

Lin, Yueh-Hsien; Chen, Yu-Pei; Ho, Kuo-Ling; Lee, Tsung-Yih; Tseng, Ching-Ping

2013-01-01

Several different foul odors such as nitrogen-containing groups, sulfur-containing groups, and short-chain fatty-acids commonly emitted from composting facilities. In this study, an experimental laboratory-scale bioreactor was scaled up to build a large-scale modular biofiltration system that can process 34 m(3)min(-1)waste gases. This modular reactor system was proven effective in eliminating odors, with a 97% removal efficiency for 96 ppm ammonia, a 98% removal efficiency for 220 ppm amines, and a 100% removal efficiency of other odorous substances. The results of operational parameters indicate that this modular biofiltration system offers long-term operational stability. Specifically, a low pressure drop (<45 mmH2O m(-1)) was observed, indicating that the packing carrier in bioreactor units does not require frequent replacement. Thus, this modular biofiltration system can be used in field applications to eliminate various odors with compact working volume.

Joint Chemical Agent Detector (JCAD): the future of chemical agent detection

NASA Astrophysics Data System (ADS)

Laljer, Charles E.; Owen, Jeffery L.

2002-06-01

The Joint Chemical Agent Detector (JCAD) will provide state of the art chemical warfare agent detection capability to ground vehicle operators. Intelligence sources estimate that over twenty counties have active chemical weapons programs. The spread of chemical weapons to third world nations, coupled with the potential for US involvement in these areas in an operational or support capacity, increases the probability that the Joint Services may encounter chemical agents and toxic industrial materials anywhere in the world. Currently, fielded chemical agent detectors are bulky, labor intensive, and subject to false readings. No legacy detector is sensitive enough to provide detection and warning of the low dose hazards associated with miosis contamination. The JCAD will provide a small, lightweight chemical agent detector for vehicle interiors, aircraft, individual personnel, shipboard, and fixed site locations. The system provides a common detection components across multi-service platforms. This common detector system will allow the Joint Services to use the same operational and support concept for more efficient utilization of resources. The JCAD will detect, identify, quantify, and warn of the presence of chemical agents prior to onset of miosis. Upon detection of chemical agents, the detector will provide local and remote audible and visual alarms to the operators. Advance warning will provide the vehicle crew with the time necessary to protect themselves from the lethal effects of chemical agents. The JCAD will also be capable of being upgraded to protect against future chemical agent threats. The JCAD will provide the vehicle operators with the warning necessary to survive and fight in a chemical warfare agent threat environment.

NASA Integrated Space Communications Network

NASA Technical Reports Server (NTRS)

Tai, Wallace; Wright, Nate; Prior, Mike; Bhasin, Kul

2012-01-01

The NASA Integrated Network for Space Communications and Navigation (SCaN) has been in the definition phase since 2010. It is intended to integrate NASA s three existing network elements, i.e., the Space Network, Near Earth Network, and Deep Space Network, into a single network. In addition to the technical merits, the primary purpose of the Integrated Network is to achieve a level of operating cost efficiency significantly higher than it is today. Salient features of the Integrated Network include (a) a central system element that performs service management functions and user mission interfaces for service requests; (b) a set of common service execution equipment deployed at the all stations that provides return, forward, and radiometric data processing and delivery capabilities; (c) the network monitor and control operations for the entire integrated network are conducted remotely and centrally at a prime-shift site and rotating among three sites globally (a follow-the-sun approach); (d) the common network monitor and control software deployed at all three network elements that supports the follow-the-sun operations.

Determining Parameters of Double-Wiebe Function for Simulation of Combustion Process in Overload Diesel Engine with Common Rail Fuel Feed System

NASA Astrophysics Data System (ADS)

Kamaltdinov, V. G.; Markov, V. A.; Lysov, I. O.

2018-03-01

To analyze the peculiarities of the combustion process in an overload diesel engine with the system of Common Rail type with one-stage injection, the indicator diagram was registered. The parameters of the combustion process simulated by the double-Wiebe function were calculated as satisfactorily reconstructing the law of burning rate variation. The main parameters of the operating cycle obtained through the indicator diagram processing and the double-Wiebe function calculation differed insignificantly. And the calculated curve of the cylinder pressure differed notably only in the end of the expansion stroke. To improve the performance of the diesel engine, a two-stage fuel injection was recommended.

Argument-Based Airworthiness Assurance of Small UAS

NASA Technical Reports Server (NTRS)

Denney, Ewen; Pai, Ganesh

2015-01-01

Presently, there are three avenues by which Unmanned Aircraft System (UAS) operations are authorized in the U.S. National Airspace System (NAS): obtaining either (i) a certificate of authorization (COA), or (ii) a special airworthiness certificate (SAC) in either the experimental, or the restricted category, or (iii) an exemption from an airworthiness certificate together with a civil COA. The first is meant primarily for public entities, such as NASA; the remaining two are the only available means for civil UAS operations. Recently, the Federal Aviation Administration (FAA) has also proposed a regulatory framework targeted for certain small UAS, specifically those weighing 55 pounds or less, although final rulemaking remains pending. We have previously shown how an assurance case can aggregate heterogeneous reasoning and safety evidence, with application to UAS safety. In this paper, we describe how assurance cases can serve as a common framework to justify overall system safety, unifying both operational aspects and airworthiness, in particular system design assurance. We also show how this approach can coexist with, and augment, existing safety analysis processes and best-practices, by transforming the artifacts they produce into structured assurance arguments. To illustrate the applicability and utility of our approach, we have been applying it for the design assurance of an unmanned rotorcraft system, intended for precision agriculture operations, as part of the NASA Unmanned Aircraft System (UAS) Integration in the National Airspace System (NAS) project.

Auditory display as feedback for a novel eye-tracking system for sterile operating room interaction.

PubMed

Black, David; Unger, Michael; Fischer, Nele; Kikinis, Ron; Hahn, Horst; Neumuth, Thomas; Glaser, Bernhard

2018-01-01

The growing number of technical systems in the operating room has increased attention on developing touchless interaction methods for sterile conditions. However, touchless interaction paradigms lack the tactile feedback found in common input devices such as mice and keyboards. We propose a novel touchless eye-tracking interaction system with auditory display as a feedback method for completing typical operating room tasks. Auditory display provides feedback concerning the selected input into the eye-tracking system as well as a confirmation of the system response. An eye-tracking system with a novel auditory display using both earcons and parameter-mapping sonification was developed to allow touchless interaction for six typical scrub nurse tasks. An evaluation with novice participants compared auditory display with visual display with respect to reaction time and a series of subjective measures. When using auditory display to substitute for the lost tactile feedback during eye-tracking interaction, participants exhibit reduced reaction time compared to using visual-only display. In addition, the auditory feedback led to lower subjective workload and higher usefulness and system acceptance ratings. Due to the absence of tactile feedback for eye-tracking and other touchless interaction methods, auditory display is shown to be a useful and necessary addition to new interaction concepts for the sterile operating room, reducing reaction times while improving subjective measures, including usefulness, user satisfaction, and cognitive workload.

[Current status and changes of metabolic and bariatric surgery in China].

PubMed

Liu, Jingang

2017-04-25

Through continuous development, metabolic and bariatric surgery (MBS) has become widely recognized in academic and medical circles. In China, the volume of MBS operations has increased year by year. Therapeutic goals of MBS have evolved from treating obesity to treating Type 2 diabetes mellitus, and further to treating a series of obesity-associated metabolic diseases (including conditions in the endocrine system, circulatory system, respiratory system, reproductive system, and etc). Surgical approach of MBS has also been evolving continuously. Currently the common surgical procedures include laparoscopic Roux-en-Y gastric bypass (LRYGB), laparoscopic sleeve gastrectomy (LSG), laparoscopic adjustable gastric banding (LAGB) and bilio-pancreatic diversion with duodenal switch (BPD-DS). All surgical procedures have pros and cons, and the choice of surgical procedures should be based on the conditions of patients, the surgeon's technical ability, and benefits and operative risks. With the development of MBS, the proportions of different surgical procedures also changed in China. In recent five years, the proportion of AGB has decreased continuously and LAGB is no longer a common procedure. The proportion of LSG has increased rapidly, rising from 9% in 2010 to 55% in 2015. The proportion of RYGB has increased from 57% to 64% between 2010 and 2013, and remained at 45% afterwards. Since 2010, most MBS operations are laparoscopic surgery. 3D Laparoscopic surgery, laparoendoscopic single-site surgery and da Vinci Robotic Surgery have also been introduced in MBS. This review discusses the status quo and changes of MBS in china, as well as the new technology in MBS, aiming to strengthen the information and comprehension of MBS in china.

Novel application of simultaneous multi-image display during complex robotic abdominal procedures

PubMed Central

2014-01-01

Background The surgical robot offers the potential to integrate multiple views into the surgical console screen, and for the assistant’s monitors to provide real-time views of both fields of operation. This function has the potential to increase patient safety and surgical efficiency during an operation. Herein, we present a novel application of the multi-image display system for simultaneous visualization of endoscopic views during various complex robotic gastrointestinal operations. All operations were performed using the da Vinci Surgical System (Intuitive Surgical, Sunnyvale, CA, USA) with the assistance of Tilepro, multi-input display software, during employment of the intraoperative scopes. Three robotic operations, left hepatectomy with intraoperative common bile duct exploration, low anterior resection, and radical distal subtotal gastrectomy with intracorporeal gastrojejunostomy, were performed by three different surgeons at a tertiary academic medical center. Results The three complex robotic abdominal operations were successfully completed without difficulty or intraoperative complications. The use of the Tilepro to simultaneously visualize the images from the colonoscope, gastroscope, and choledochoscope made it possible to perform additional intraoperative endoscopic procedures without extra monitors or interference with the operations. Conclusion We present a novel use of the multi-input display program on the da Vinci Surgical System to facilitate the performance of intraoperative endoscopies during complex robotic operations. Our study offers another potentially beneficial application of the robotic surgery platform toward integration and simplification of combining additional procedures with complex minimally invasive operations. PMID:24628761

Normalization as a canonical neural computation

PubMed Central

Carandini, Matteo; Heeger, David J.

2012-01-01

There is increasing evidence that the brain relies on a set of canonical neural computations, repeating them across brain regions and modalities to apply similar operations to different problems. A promising candidate for such a computation is normalization, in which the responses of neurons are divided by a common factor that typically includes the summed activity of a pool of neurons. Normalization was developed to explain responses in the primary visual cortex and is now thought to operate throughout the visual system, and in many other sensory modalities and brain regions. Normalization may underlie operations such as the representation of odours, the modulatory effects of visual attention, the encoding of value and the integration of multisensory information. Its presence in such a diversity of neural systems in multiple species, from invertebrates to mammals, suggests that it serves as a canonical neural computation. PMID:22108672

Situation management in the Link Monitor and Control Operator Assistant (LMCOA)

NASA Technical Reports Server (NTRS)

Hill, Randall W., Jr.; Lee, Lorrine F.

1993-01-01

This paper describes a knowledge-based system called the Situation Manager that was developed for the Link Monitor and Control Operator Assistant (LMCOA) at the Jet Propulsion Laboratory. This system was developed in response to a number of deficiencies that were identified in an earlier version of the LMCOA: the need to close the control loop between sending a directive and knowing when its execution is complete (versus just closing the communications loop), the need to recognize an anomaly and alert the operator when a directive is rejected or a link device fails, and the need to suggest ways to work around an anomaly, provided that it is recognizable. In response to these needs, the Situation Manager has been designed to provide the LMCOA with three basic capabilities: situation assessment, anomaly diagnosis, and recovery from commonly occurring problems.

The Large Synoptic Survey Telescope OCS and TCS models

NASA Astrophysics Data System (ADS)

Schumacher, German; Delgado, Francisco

2010-07-01

The Large Synoptic Survey Telescope (LSST) is a project envisioned as a system of systems with demanding science, technical, and operational requirements, that must perform as a fully integrated unit. The design and implementation of such a system poses big engineering challenges when performing requirements analysis, detailed interface definitions, operational modes and control strategy studies. The OMG System Modeling Language (SysML) has been selected as the framework for the systems engineering analysis and documentation for the LSST. Models for the overall system architecture and different observatory subsystems have been built describing requirements, structure, interfaces and behavior. In this paper we show the models for the Observatory Control System (OCS) and the Telescope Control System (TCS), and how this methodology has helped in the clarification of the design and requirements. In one common language, the relationships of the OCS, TCS, Camera and Data management subsystems are captured with models of the structure, behavior, requirements and the traceability between them.

Strengthening the Security of ESA Ground Data Systems

NASA Astrophysics Data System (ADS)

Flentge, Felix; Eggleston, James; Garcia Mateos, Marc

2013-08-01

A common approach to address information security has been implemented in ESA's Mission Operations (MOI) Infrastructure during the last years. This paper reports on the specific challenges to the Data Systems domain within the MOI and how security can be properly managed with an Information Security Management System (ISMS) according to ISO 27001. Results of an initial security risk assessment are reported and the different types of security controls that are being implemented in order to reduce the risks are briefly described.

Border Collision of Three-Phase Voltage-Source Inverter System with Interacting Loads

NASA Astrophysics Data System (ADS)

Li, Zhen; Liu, Bin; Li, Yining; Wong, Siu-Chung; Liu, Xiangdong; Huang, Yuehui

As a commercial interface, three-phase voltage-source inverters (VSI) are commonly equipped for energy conversion to export DC power from most distributed generation (DG) to the AC utility. Not only do voltage-source converters take charge of converting the power to the loads but support the grid voltage at the point of common connection (PCC) as well, which is dependent on the condition of the grid-connected loads. This paper explores the border collision and its interacting mechanism among the VSI, resistive interacting loads and grids, which manifests as the alternating emergence of the inverting and rectifying operations, where the normal operation is terminated and a new one is assumed. Their mutual effect on the power quality under investigation will cause the circuital stability issue and further deteriorate the voltage regulation capability of VSI by dramatically raising the grid voltage harmonics. It is found in a design-oriented view that the border collision operation will be induced within the unsuitable parameter space with respect to transmission lines of AC grid, resistive loads and internal resistance of VSI. The physical phenomenon is also identified by the theoretical analysis. With numerical simulations for various circuit conditions, the corresponding bifurcation boundaries are collected, where the stability of the system is lost via border collision.

[Cleanliness in the operating room].

PubMed

Suzuki, Toshiyasu

2010-05-01

With regard to recent findings in the cleanliness of the operating room, concerning handwashing and performing operations, the traditional method of excessive scrubbing using a brush is not effective, and handwashing using only an alcohol-containing antiseptic hand rub (rubbing method) has become common practice. Use of a brush has already been abolished in some medical institutions. In addition, sterilized water used for handwashing when performing operations has no scientific basis and use of tap water is considered sufficient. Furthermore, the concept of operating room zoning has also undergone a dramatic change. It was discovered that a layout focusing on work efficiency is more desirable than the one that follows an excessively rigid zoning pattern. One-footwear System not requiring change of shoes also has various advantages in improving the efficiency of the operation room, and this is thought to become commonplace in the future.

General surgical services at an urban teaching hospital in Mozambique.

PubMed

Snyder, Elizabeth; Amado, Vanda; Jacobe, Mário; Sacks, Greg D; Bruzoni, Matias; Mapasse, Domingos; DeUgarte, Daniel A

2015-10-01

As surgery becomes incorporated into global health programs, it will be critical for clinicians to take into account already existing surgical care systems within low-income countries. To inform future efforts to expand the local system and systems in comparable regions of the developing world, we aimed to describe current patterns of surgical care at a major urban teaching hospital in Mozambique. We performed a retrospective review of all general surgery patients treated between August 2012 and August 2013 at the Hospital Central Maputo in Maputo, Mozambique. We reviewed emergency and elective surgical logbooks, inpatient discharge records, and death records to report case volume, disease etiology, and mortality. There were 1598 operations (910 emergency and 688 elective) and 2606 patient discharges during our study period. The most common emergent surgeries were for nontrauma laparotomy (22%) followed by all trauma procedures (18%), whereas the most common elective surgery was hernia repair (31%). The majority of lower extremity amputations were above knee (69%). The most common diagnostic categories for inpatients were infectious (31%), trauma (18%), hernia (12%), neoplasm (10%), and appendicitis (5%). The mortality rate was 5.6% (146 deaths), approximately half of which were related to sepsis. Our data demonstrate the general surgery caseload of a large, academic, urban training and referral center in Mozambique. We describe resource limitations that impact operative capacity, trauma care, and management of amputations and cancer. These findings highlight challenges that are applicable to a broad range of global surgery efforts. Copyright © 2015 Elsevier Inc. All rights reserved.

A knowledge acquisition process to analyse operational problems in solid waste management facilities.

PubMed

Dokas, Ioannis M; Panagiotakopoulos, Demetrios C

2006-08-01

The available expertise on managing and operating solid waste management (SWM) facilities varies among countries and among types of facilities. Few experts are willing to record their experience, while few researchers systematically investigate the chains of events that could trigger operational failures in a facility; expertise acquisition and dissemination, in SWM, is neither popular nor easy, despite the great need for it. This paper presents a knowledge acquisition process aimed at capturing, codifying and expanding reliable expertise and propagating it to non-experts. The knowledge engineer (KE), the person performing the acquisition, must identify the events (or causes) that could trigger a failure, determine whether a specific event could trigger more than one failure, and establish how various events are related among themselves and how they are linked to specific operational problems. The proposed process, which utilizes logic diagrams (fault trees) widely used in system safety and reliability analyses, was used for the analysis of 24 common landfill operational problems. The acquired knowledge led to the development of a web-based expert system (Landfill Operation Management Advisor, http://loma.civil.duth.gr), which estimates the occurrence possibility of operational problems, provides advice and suggests solutions.

Status quo and current trends of operating room management in Germany.

PubMed

Baumgart, André; Schüpfer, Guido; Welker, Andreas; Bender, Hans-Joachim; Schleppers, Alexander

2010-04-01

Ongoing healthcare reforms in Germany have required strenuous efforts to adapt hospital and operating room organizations to the needs of patients, new technological developments, and social and economic demands. This review addresses the major developments in German operating room management research and current practice. The introduction of the diagnosis-related group system in 2003 has changed the incentive structure of German hospitals to redesign their operating room units. The role of operating room managers has been gradually changing in hospitals in response to the change in the reimbursement system. Operating room managers are today specifically qualified and increasingly externally hired staff. They are more and more empowered with authority to plan and control operating rooms as profit centers. For measuring performance, common perioperative performance indicators are still scarcely implemented in German hospitals. In 2008, a concerted time glossary was established to enable consistent monitoring of operating room performance with generally accepted process indicators. These key performance indicators are a consistent way to make a procedure or case - and also the effectiveness of the operating room management - more transparent. In the presence of increasing financial pressure, a hospital's executives need to empower an independent operating room management function to achieve the hospital's economic goals. Operating room managers need to adopt evidence-based methods also from other scientific fields, for example management science and information technology, to further sustain operating room performance.

Intelligent Launch and Range Operations Virtual Test Bed (ILRO-VTB)

NASA Technical Reports Server (NTRS)

Bardina, Jorge; Rajkumar, T.

2003-01-01

Intelligent Launch and Range Operations Virtual Test Bed (ILRO-VTB) is a real-time web-based command and control, communication, and intelligent simulation environment of ground-vehicle, launch and range operation activities. ILRO-VTB consists of a variety of simulation models combined with commercial and indigenous software developments (NASA Ames). It creates a hybrid software/hardware environment suitable for testing various integrated control system components of launch and range. The dynamic interactions of the integrated simulated control systems are not well understood. Insight into such systems can only be achieved through simulation/emulation. For that reason, NASA has established a VTB where we can learn the actual control and dynamics of designs for future space programs, including testing and performance evaluation. The current implementation of the VTB simulates the operations of a sub-orbital vehicle of mission, control, ground-vehicle engineering, launch and range operations. The present development of the test bed simulates the operations of Space Shuttle Vehicle (SSV) at NASA Kennedy Space Center. The test bed supports a wide variety of shuttle missions with ancillary modeling capabilities like weather forecasting, lightning tracker, toxic gas dispersion model, debris dispersion model, telemetry, trajectory modeling, ground operations, payload models and etc. To achieve the simulations, all models are linked using Common Object Request Broker Architecture (CORBA). The test bed provides opportunities for government, universities, researchers and industries to do a real time of shuttle launch in cyber space.

Intelligent launch and range operations virtual testbed (ILRO-VTB)

NASA Astrophysics Data System (ADS)

Bardina, Jorge; Rajkumar, Thirumalainambi

2003-09-01

Intelligent Launch and Range Operations Virtual Test Bed (ILRO-VTB) is a real-time web-based command and control, communication, and intelligent simulation environment of ground-vehicle, launch and range operation activities. ILRO-VTB consists of a variety of simulation models combined with commercial and indigenous software developments (NASA Ames). It creates a hybrid software/hardware environment suitable for testing various integrated control system components of launch and range. The dynamic interactions of the integrated simulated control systems are not well understood. Insight into such systems can only be achieved through simulation/emulation. For that reason, NASA has established a VTB where we can learn the actual control and dynamics of designs for future space programs, including testing and performance evaluation. The current implementation of the VTB simulates the operations of a sub-orbital vehicle of mission, control, ground-vehicle engineering, launch and range operations. The present development of the test bed simulates the operations of Space Shuttle Vehicle (SSV) at NASA Kennedy Space Center. The test bed supports a wide variety of shuttle missions with ancillary modeling capabilities like weather forecasting, lightning tracker, toxic gas dispersion model, debris dispersion model, telemetry, trajectory modeling, ground operations, payload models and etc. To achieve the simulations, all models are linked using Common Object Request Broker Architecture (CORBA). The test bed provides opportunities for government, universities, researchers and industries to do a real time of shuttle launch in cyber space.

Modular System to Enable Extravehicular Activity

NASA Technical Reports Server (NTRS)

Sargusingh, Miriam J.

2011-01-01

The ability to perform extravehicular activity (EVA), both human and robotic, has been identified as a key component to space missions to support such operations as assembly and maintenance of space system (e.g. construction and maintenance of the International Space Station), and unscheduled activities to repair an element of the transportation and habitation systems that can only be accessed externally and via unpressurized areas. In order to make human transportation beyond lower earth orbit (BLEO) practical, efficiencies must be incorporated into the integrated transportation systems to reduce system mass and operational complexity. Affordability is also a key aspect to be considered in space system development; this could be achieved through commonality, modularity and component reuse. Another key aspect identified for the EVA system was the ability to produce flight worthy hardware quickly to support early missions and near Earth technology demonstrations. This paper details a conceptual architecture for a modular extravehicular activity system (MEVAS) that would meet these stated needs for EVA capability that is affordable, and that could be produced relatively quickly. Operational concepts were developed to elaborate on the defined needs and define the key capabilities, operational and design constraints, and general timelines. The operational concept lead to a high level design concept for a module that interfaces with various space transportation elements and contains the hardware and systems required to support human and telerobotic EVA; the module would not be self-propelled and would rely on an interfacing element for consumable resources. The conceptual architecture was then compared to EVA Systems used in the Shuttle Orbiter, on the International Space Station to develop high level design concepts that incorporate opportunities for cost savings through hardware reuse, and quick production through the use of existing technologies and hardware designs. An upgrade option was included to make use of the developing suitport technologies.

DARPA DTN Phase 3 Core Engineering Support

NASA Technical Reports Server (NTRS)

Torgerson, J. Leigh; Richard Borgen, Richard; McKelvey, James; Segui, John; Tsao, Phil

2010-01-01

This report covers the initial DARPA DTN Phase 3 activities as JPL provided Core Engineering Support to the DARPA DTN Program, and then further details the culmination of the Phase 3 Program with a systematic development, integration and test of a disruption-tolerant C2 Situation Awareness (SA) system that may be transitioned to the USMC and deployed in the near future. The system developed and tested was a SPAWAR/JPL-Developed Common Operating Picture Fusion Tool called the Software Interoperability Environment (SIE), running over Disruption Tolerant Networking (DTN) protocols provided by BBN and MITRE, which effectively extends the operational range of SIE from normal fully-connected internet environments to the mobile tactical edges of the battlefield network.

Development of user guidelines for ECAS display design, volume 1

NASA Technical Reports Server (NTRS)

Dodson, D. W.; Shields, N. L., Jr.

1978-01-01

Experiment computer application software (ECAS) display design and command usage guidelines were developed, which if followed by spacelab experiments, would standardize methods and techniques for data presentation and commanding via ECAS. These guidelines would provide some commonality among experiments which would enhance crew training and flight operations. The guidelines are applicable to all onboard experiment displays, whether allocated by ECAS or a dedicated experiment processor. A brief description of the spacelab data display system characteristics and of the services provided by the experiment computer operating system is included. Guidelines concerning data presentation and layout of alphanumeric and graphic information are presented along with guidelines concerning keyboard commanding and command feedback.

Development and evaluation of a Kalman-filter algorithm for terminal area navigation using sensors of moderate accuracy

NASA Technical Reports Server (NTRS)

Kanning, G.; Cicolani, L. S.; Schmidt, S. F.

1983-01-01

Translational state estimation in terminal area operations, using a set of commonly available position, air data, and acceleration sensors, is described. Kalman filtering is applied to obtain maximum estimation accuracy from the sensors but feasibility in real-time computations requires a variety of approximations and devices aimed at minimizing the required computation time with only negligible loss of accuracy. Accuracy behavior throughout the terminal area, its relation to sensor accuracy, its effect on trajectory tracking errors and control activity in an automatic flight control system, and its adequacy in terms of existing criteria for various terminal area operations are examined. The principal investigative tool is a simulation of the system.

Department of Defense Joint Technical Architecture Version 2.0

DTIC Science & Technology

1998-05-26

Mandates 2.1-5 2.1.4.1 Year 2000 (Y2K) Compliance 2.1-5 2.1.4.2 Defense Information Infrastructure Common Operating Environment (DU COE) 2.1-5 2.1.5...2.2.2.2.1.6 Communications Services 2.2-11 2.2.2.2.1.7 Operating System Services 2.2-11 2.2.2.2.2 Application Platform Cross-Area Services 2.2- 12 ...2.2.2.2.2.1 Internationalization Services 2.2- 12 2.2.2.2.2.2 Security Services 2.2- 12 2.2.2.2.2.3 System Management Services 2.2- 12 2.2.2.2.2.4

Japanese style total quality control: A first hand experience

NASA Astrophysics Data System (ADS)

Cook, S. C.

1991-11-01

The scope, concepts and practices of Total Quality Control (TQC) as operated in Japan today are described. The following mechanisms and elements are introduced: policy deployment, cross functional management, small group activities, suggestion systems, standardization, the TQC promotion department, and TQC education. It is shown on a practical level, how TQC operates in the research and engineering divisions of the aeroengine and space operation at Ishikawajima Harima Industries in Japan. Japanese style TQC is a well developed, well promoted, well structured, common approach to achieving customer satisfaction through continuous improvements. Furthermore, TQC itself is being continuously improved with the Japanese still refining, extending, and developing TQC.

An operating system for future aerospace vehicle computer systems

NASA Technical Reports Server (NTRS)

Foudriat, E. C.; Berman, W. J.; Will, R. W.; Bynum, W. L.

1984-01-01

The requirements for future aerospace vehicle computer operating systems are examined in this paper. The computer architecture is assumed to be distributed with a local area network connecting the nodes. Each node is assumed to provide a specific functionality. The network provides for communication so that the overall tasks of the vehicle are accomplished. The O/S structure is based upon the concept of objects. The mechanisms for integrating node unique objects with node common objects in order to implement both the autonomy and the cooperation between nodes is developed. The requirements for time critical performance and reliability and recovery are discussed. Time critical performance impacts all parts of the distributed operating system; e.g., its structure, the functional design of its objects, the language structure, etc. Throughout the paper the tradeoffs - concurrency, language structure, object recovery, binding, file structure, communication protocol, programmer freedom, etc. - are considered to arrive at a feasible, maximum performance design. Reliability of the network system is considered. A parallel multipath bus structure is proposed for the control of delivery time for time critical messages. The architecture also supports immediate recovery for the time critical message system after a communication failure.

Applications of superconducting bolometers in security imaging

NASA Astrophysics Data System (ADS)

Luukanen, A.; Leivo, M. M.; Rautiainen, A.; Grönholm, M.; Toivanen, H.; Grönberg, L.; Helistö, P.; Mäyrä, A.; Aikio, M.; Grossman, E. N.

2012-12-01

Millimeter-wave (MMW) imaging systems are currently undergoing deployment World-wide for airport security screening applications. Security screening through MMW imaging is facilitated by the relatively good transmission of these wavelengths through common clothing materials. Given the long wavelength of operation (frequencies between 20 GHz to ~ 100 GHz, corresponding to wavelengths between 1.5 cm and 3 mm), existing systems are suited for close-range imaging only due to substantial diffraction effects associated with practical aperture diameters. The present and arising security challenges call for systems that are capable of imaging concealed threat items at stand-off ranges beyond 5 meters at near video frame rates, requiring substantial increase in operating frequency in order to achieve useful spatial resolution. The construction of such imaging systems operating at several hundred GHz has been hindered by the lack of submm-wave low-noise amplifiers. In this paper we summarize our efforts in developing a submm-wave video camera which utilizes cryogenic antenna-coupled microbolometers as detectors. Whilst superconducting detectors impose the use of a cryogenic system, we argue that the resulting back-end complexity increase is a favorable trade-off compared to complex and expensive room temperature submm-wave LNAs both in performance and system cost.

Electric circuit breaker comprising a plurality of vacuum interrupters simultaneously operated by a common operator

DOEpatents

Barkan, Philip; Imam, Imdad

1980-01-01

This circuit breaker comprises a plurality of a vacuum-type circuit interrupters, each having a movable contact rod. A common operating device for the interrupters comprises a linearly-movable operating member. The interrupters are mounted at one side of the operating member with their movable contact rods extending in a direction generally toward the operating member. Means is provided for mechanically coupling the operating member to the contact rods, and this means comprises a plurality of insulating operating rods, each connected at one end to the operating member and at its opposite end to one of the movable contact rods. The operating rods are of substantially equal length and have longitudinal axes that converge and intersect at substantially a common point.

Apparatus and method for detecting and measuring changes in linear relationships between a number of high frequency signals

DOEpatents

Bittner, J.W.; Biscardi, R.W.

1991-03-19

An electronic measurement circuit is disclosed for high speed comparison of the relative amplitudes of a predetermined number of electrical input signals independent of variations in the magnitude of the sum of the signals. The circuit includes a high speed electronic switch that is operably connected to receive on its respective input terminals one of said electrical input signals and to have its common terminal serve as an input for a variable-gain amplifier-detector circuit that is operably connected to feed its output to a common terminal of a second high speed electronic switch. The respective terminals of the second high speed electronic switch are operably connected to a plurality of integrating sample and hold circuits, which in turn have their outputs connected to a summing logic circuit that is operable to develop first, second and third output voltages, the first output voltage being proportional to a predetermined ratio of sums and differences between the compared input signals, the second output voltage being proportional to a second summed ratio of predetermined sums and differences between said input signals, and the third output voltage being proportional to the sum of signals to the summing logic circuit. A servo system that is operably connected to receive said third output signal and compare it with a reference voltage to develop a slowly varying feedback voltage to control the variable-gain amplifier in said common amplifier-detector circuit in order to make said first and second output signals independent of variations in the magnitude of the sum of said input signals. 2 figures.

Apparatus and method for detecting and measuring changes in linear relationships between a number of high frequency signals

DOEpatents

Bittner, John W.; Biscardi, Richard W.

1991-01-01

An electronic measurement circuit for high speed comparison of the relative amplitudes of a predetermined number of electrical input signals independent of variations in the magnitude of the sum of the signals. The circuit includes a high speed electronic switch that is operably connected to receive on its respective input terminals one of said electrical input signals and to have its common terminal serve as an input for a variable-gain amplifier-detector circuit that is operably connected to feed its output to a common terminal of a second high speed electronic switch. The respective terminals of the second high speed electronic switch are operably connected to a plurality of integrating sample and hold circuits, which in turn have their outputs connected to a summing logic circuit that is operable to develop first, second and third output voltages, the first output voltage being proportional to a predetermined ratio of sums and differences between the compared input signals, the second output voltage being proportional to a second summed ratio of predetermined sums and differences between said input signals, and the third output voltage being proportional to the sum of signals to the summing logic circuit. A servo system that is operably connected to receive said third output signal and compare it with a reference voltage to develop a slowly varying feedback voltage to control the variable-gain amplifier in said common amplifier-detector circuit in order to make said first and second output signals independent of variations in the magnitude of the sum of said input signals.

Deep Space Habitat Concept of Operations for Extended Duration Transit Missions

NASA Technical Reports Server (NTRS)

Hoffman, Stephen J.; Toups, Larry

2012-01-01

NASA's Capability-Driven Framework (CDF) describes an approach for progressively extending human exploration missions farther into the Solar System for longer periods of time as allowed by developments in technology and spacecraft systems. Within this framework design reference missions (DRMs) targeted for several specific destinations are being used to assess different combinations of vehicles, operations, and advanced technologies to help understand which combination will best support expanded human exploration both efficiently and sustainably. Several of the identified destinations have been found to require missions with a round trip duration exceeding one year. These mission durations exceed the capabilities of current human-rated spacecraft if resupply from Earth is not possible. This makes the design of an efficient and reliable Deep Space Habitat (DSH) critical for reaching these destinations. The paper will describe the current understanding of DSH capabilities and functions that must be exhibited by any future habitat design for these missions. This description of the DSH is presented in the form of a concept of operation, which focuses on the functions that any DSH must provide, as opposed to a specific DSH design concept. Development of a concept of operations, based on DRM features, provides a common basis for assessing the viability of design concepts incorporating differing configurations and technologies. A study team with representation from several NASA Centers and relevant engineering and scientific disciplines collaborated to develop this DSH concept of operations for the transit phases of these missions. The transit phase of a mission is defined as the time after leaving Earth but before arrival at the destination and the time after leaving the destination but before arriving back at Earth. These transit phases were found to have many common features across all of the destinations being assessed for the CDF and thus arguing for a common concept of operations for all of the associated DRMs. The paper first describes the CDF and potential destinations being considered within this framework. DRMs representative of those currently being assessed will then be discussed to illustrate the range of capabilities that the DSH must support. The 18 functions identified by the multi-discipline analysis team are then described at a summary level. Several specific examples of the potential use for this concept of operations are described.

Mars Surface Systems Common Capabilities and Challenges for Human Missions

NASA Technical Reports Server (NTRS)

Toups, Larry; Hoffman, Stephen J.

2016-01-01

This paper describes the current status of common systems and operations as they are applied to actual locations on Mars that are representative of Exploration Zones (EZ) - NASA's term for candidate locations where humans could land, live and work on the Martian surface. Given NASA's current concepts for human missions to Mars, an EZ is a collection of Regions of Interest (ROIs) located within approximately 100 kilometers of a centralized landing site. ROIs are areas that are relevant for scientific investigation and/or development/maturation of capabilities and resources necessary for a sustainable human presence. An EZ also contains a habitation site that will be used by multiple human crews during missions to explore and utilize the ROIs within the EZ. The Evolvable Mars Campaign (EMC), a description of NASA's current approach to these human Mars missions, assumes that a single EZ will be identified within which NASA will establish a substantial and durable surface infrastructure that will be used by multiple human crews. The process of identifying and eventually selecting this single EZ will likely take many years to finalized. Because of this extended EZ selection process it becomes important to evaluate the current suite of surface systems and operations being evaluated for the EMC as they are likely to perform at a variety of proposed EZ locations and for the types of operations - both scientific and development - that are proposed for these candidate EZs. It is also important to evaluate proposed EZs for their suitability to be explored or developed given the range of capabilities and constraints for the types of surface systems and operations being considered within the EMC. Four locations identified in the Mars Exploration Program Analysis Group (MEPAG)'s Human Exploration of Mars Science Analysis Group (HEM-SAG) report are used in this paper as representative of candidate EZs that will emerge from the selection process that NASA has initiated. A field station site plan is developed for each of these four HEM-SAG sites. Because of the difficulty in getting equipment and supplies to the surface of Mars, specific assessments have been conducted to identify those systems and processes that can perform in multiple, sometimes completely unrelated, situations. Examples of common systems that are assessed at all of these sites include: (a) habitation and associated logistics storage systems, (b) a centralized power plant capable of supplying power to a geographically distributed (but within the central habitation zone) set of systems, (c) mobility systems that can be used to off-load and move payloads to specific locations at the central field station location that could also be used to traverse long distances to reach some of the more remote ROIs and (d) robotic systems that can support various activities (such as system set up and maintenance) at the field station that could also be used to explore scientific ROIs and used to support site-specific ISRU (In Situ Resource Utilization) production activities.

Robotic systems in spine surgery.

PubMed

Onen, Mehmet Resid; Naderi, Sait

2014-01-01

Surgical robotic systems have been available for almost twenty years. The first surgical robotic systems were designed as supportive systems for laparoscopic approaches in general surgery (the first procedure was a cholecystectomy in 1987). The da Vinci Robotic System is the most common system used for robotic surgery today. This system is widely used in urology, gynecology and other surgical disciplines, and recently there have been initial reports of its use in spine surgery, for transoral access and anterior approaches for lumbar inter-body fusion interventions. SpineAssist, which is widely used in spine surgery, and Renaissance Robotic Systems, which are considered the next generation of robotic systems, are now FDA approved. These robotic systems are designed for use as guidance systems in spine instrumentation, cement augmentations and biopsies. The aim is to increase surgical accuracy while reducing the intra-operative exposure to harmful radiation to the patient and operating team personnel during the intervention. We offer a review of the published literature related to the use of robotic systems in spine surgery and provide information on using robotic systems.

Evaluation of the Next-Gen Exercise Software Interface in the NEEMO Analog

NASA Technical Reports Server (NTRS)

Hanson, Andrea; Kalogera, Kent; Sandor, Aniko; Hardy, Marc; Frank, Andrew; English, Kirk; Williams, Thomas; Perera, Jeevan; Amonette, William

2017-01-01

NSBRI (National Space Biomedical Research Institute) funded research grant to develop the 'NextGen' exercise software for the NEEMO (NASA Extreme Environment Mission Operations) analog. Develop a software architecture to integrate instructional, motivational and socialization techniques into a common portal to enhance exercise countermeasures in remote environments. Increase user efficiency and satisfaction, and institute commonality across multiple exercise systems. Utilized GUI (Graphical User Interface) design principals focused on intuitive ease of use to minimize training time and realize early user efficiency. Project requirement to test the software in an analog environment. Top Level Project Aims: 1) Improve the usability of crew interface software to exercise CMS (Crew Management System) through common app-like interfaces. 2) Introduce virtual instructional motion training. 3) Use virtual environment to provide remote socialization with family and friends, improve exercise technique, adherence, motivation and ultimately performance outcomes.

Wireless data transmission for high energy physics applications

NASA Astrophysics Data System (ADS)

Dittmeier, Sebastian; Brenner, Richard; Dancila, Dragos; Dehos, Cedric; De Lurgio, Patrick; Djurcic, Zelimir; Drake, Gary; Gonzalez Gimenez, Jose Luis; Gustafsson, Leif; Kim, Do-Won; Locci, Elizabeth; Pfeiffer, Ullrich; Röhrich, Dieter; Rydberg, Anders; Schöning, André; Siligaris, Alexandre; Soltveit, Hans Kristian; Ullaland, Kjetil; Vincent, Pierre; Rodriguez Vazquez, Pedro; Wiedner, Dirk; Yang, Shiming

2017-08-01

Silicon tracking detectors operated at high luminosity collider experiments pose a challenge for current and future readout systems regarding bandwidth, radiation, space and power constraints. With the latest developments in wireless communications, wireless readout systems might be an attractive alternative to commonly used wired optical and copper based readout architectures. The WADAPT group (Wireless Allowing Data and Power Transmission) has been formed to study the feasibility of wireless data transmission for future tracking detectors. These proceedings cover current developments focused on communication in the 60 GHz band. This frequency band offers a high bandwidth, a small form factor and an already mature technology. Motivation for wireless data transmission for high energy physics application and the developments towards a demonstrator prototype are summarized. Feasibility studies concerning the construction and operation of a wireless transceiver system have been performed. Data transmission tests with a transceiver prototype operating at even higher frequencies in the 240 GHz band are described. Data transmission at rates up to 10 Gb/s have been obtained successfully using binary phase shift keying.

A comparison of position and rate control for telemanipulations with consideration of manipulator system dynamics

NASA Technical Reports Server (NTRS)

Kim, Won S.; Tendick, Frank; Stark, Lawrence W.; Ellis, Stephen R.

1987-01-01

Position and rate control are the two common manual control modes in teleoperations. Human operator performance using the two modes is evaluated and compared. Simulated three-axis pick-and-place operations are used as the primary task for evaluation. First, ideal position and rate control are compared by considering several factors, such as joystick gain, joystick type, display mode, task, and manipulator work space size. Then the effects of the manipulator system dynamics are investigated by varying the natural frequency and speed limit. Experimental results show that ideal position control is superior to ideal rate control, regardless of joystick type or display mode, when the manipulation work space is small or comparable to the human operator's control space. Results also show that when the manipulator system is slow, the superiority of position control disappears. Position control is recommended for small-work-space telemanipulation tasks, while rate control is recommended for slow wide-work-space telemanipulation tasks.

Short-Term Load Forecasting Error Distributions and Implications for Renewable Integration Studies: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hodge, B. M.; Lew, D.; Milligan, M.

2013-01-01

Load forecasting in the day-ahead timescale is a critical aspect of power system operations that is used in the unit commitment process. It is also an important factor in renewable energy integration studies, where the combination of load and wind or solar forecasting techniques create the net load uncertainty that must be managed by the economic dispatch process or with suitable reserves. An understanding of that load forecasting errors that may be expected in this process can lead to better decisions about the amount of reserves necessary to compensate errors. In this work, we performed a statistical analysis of themore » day-ahead (and two-day-ahead) load forecasting errors observed in two independent system operators for a one-year period. Comparisons were made with the normal distribution commonly assumed in power system operation simulations used for renewable power integration studies. Further analysis identified time periods when the load is more likely to be under- or overforecast.« less

Using Smartphones for Research Outside Clinical Settings: How Operating Systems, App Developers, and Users Determine Geolocation Data Quality in mHealth Studies.

PubMed

Beukenhorst, A L; Schultz, D M; McBeth, J; Lakshminarayana, R; Sergeant, J C; Dixon, W G

2017-01-01

Smartphones that collect user geolocation provid opportunities for mobile Health (mHealth). Although granularity of geolocation data may be high, data completeness depends on the device's operating system, application developer decisions, and user actions. We investigate completeness of geolocation data collected via smartphones of 5601 people that self-reported daily chronic pain symptoms on 349,293 days. On 17% of these days, hourly geolocation data is reported, but days with 0 (16%), 1 (14%) and 2 (13%) geolocations are common. Android phones collect geolocation more often than iPhones (median 17 versus 2 times a day). Factors on operating system level and individual user level influence completeness of geolocation data collected with smartphones. mHealth researchers should be aware of these factors when designing their studies. The mHealth research community should devise standards for reporting geolocation data quality, analysing systematic differences in data quality between participant groups, and methods for data imputation.

Executable Architecture Research at Old Dominion University

NASA Technical Reports Server (NTRS)

Tolk, Andreas; Shuman, Edwin A.; Garcia, Johnny J.

2011-01-01

Executable Architectures allow the evaluation of system architectures not only regarding their static, but also their dynamic behavior. However, the systems engineering community do not agree on a common formal specification of executable architectures. To close this gap and identify necessary elements of an executable architecture, a modeling language, and a modeling formalism is topic of ongoing PhD research. In addition, systems are generally defined and applied in an operational context to provide capabilities and enable missions. To maximize the benefits of executable architectures, a second PhD effort introduces the idea of creating an executable context in addition to the executable architecture. The results move the validation of architectures from the current information domain into the knowledge domain and improve the reliability of such validation efforts. The paper presents research and results of both doctoral research efforts and puts them into a common context of state-of-the-art of systems engineering methods supporting more agility.

Autonomously managed electrical power systems

NASA Technical Reports Server (NTRS)

Callis, Charles P.

1986-01-01

The electric power systems for future spacecraft such as the Space Station will necessarily be more sophisticated and will exhibit more nearly autonomous operation than earlier spacecraft. These new power systems will be more reliable and flexible than their predecessors offering greater utility to the users. Automation approaches implemented on various power system breadboards are investigated. These breadboards include the Hubble Space Telescope power system test bed, the Common Module Power Management and Distribution system breadboard, the Autonomusly Managed Power System (AMPS) breadboard, and the 20 kilohertz power system breadboard. Particular attention is given to the AMPS breadboard. Future plans for these breadboards including the employment of artificial intelligence techniques are addressed.

Application of total care time and payment per unit time model for physician reimbursement for common general surgery operations.

PubMed

Chatterjee, Abhishek; Holubar, Stefan D; Figy, Sean; Chen, Lilian; Montagne, Shirley A; Rosen, Joseph M; Desimone, Joseph P

2012-06-01

The relative value unit system relies on subjective measures of physician input in the care of patients. A payment per unit time model incorporates surgeon reimbursement to the total care time spent in the operating room, postoperative in-house, and clinic time to define payment per unit time. We aimed to compare common general surgery operations by using the total care time and payment per unit time method in order to demonstrate a more objective measurement for physician reimbursement. Average total physician payment per case was obtained for 5 outpatient operations and 4 inpatient operations in general surgery. Total care time was defined as the sum of operative time, 30 minutes per hospital day, and 30 minutes per office visit for each operation. Payment per unit time was calculated by dividing the physician reimbursement per case by the total care time. Total care time, physician payment per case, and payment per unit time for each type of operation demonstrated that an average payment per time spent for inpatient operations was $455.73 and slightly more at $467.51 for outpatient operations. Partial colectomy with primary anastomosis had the longest total care time (8.98 hours) and the least payment per unit time ($188.52). Laparoscopic gastric bypass had the highest payment per time ($707.30). The total care time and payment per unit time method can be used as an adjunct to compare reimbursement among different operations on an institutional level as well as on a national level. Although many operations have similar payment trends based on time spent by the surgeon, payment differences using this methodology are seen and may be in need of further review. Copyright © 2012 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

ISRU Development Strategy and Recent Activities to Support Near and Far Term Missions

NASA Astrophysics Data System (ADS)

Baird, Russell S.; Sanders, Gerald B.; Simon, Thomas M.

2003-01-01

The practical expansion of humans beyond low Earth orbit into near-Earth space and out into the solar system for exploration, commercialization, tourism, and colonization will require the effective utilization of whatever indigenous resources are available to make these endeavors economically feasible and capable of extended operations. This concept of ``living off the land'' is called In-Situ Resource Utilization (ISRU). The resources available for ISRU applications vary widely, depending upon the location. However, there are resources, technologies, and processes that are common to multiple destinations and ISRU-related applications. These resources range from carbon dioxide (CO2) and water vapor found in human habitats (surface & spacecraft) and in the Martian atmosphere, to water (ice and hydrated minerals) and various oxygen, carbon, and metal-bearing resources found on comets and asteroids, and in planetary surface materials at numerous destinations of interest (Moon, Mars, Titan, and Europa). Many parties are investigating the common technologies and processes to effectively extract and use these resources. This paper will discuss how ISRU is enabling for both near and far term human exploration missions, and present a summary of recent and on-going ISRU work sponsored by the NASA/Johnson Space Center. Technology development activities that will be described in detail include an advanced CO2 freezer acquisition system, a multi-fluid common bulkhead cryogenic storage tank, and a variety of microchannel chemical reactor concepts. Recent advanced Sabatier reactor concept development activities in preparation for later, end-to-end system testing will be described as well. This paper will also discuss an ISRU-based strategy to enable extensive robotic and human surface exploration operations and a related on-going demonstration program for a fuel cell based power plant for rover applications. Technology commonalities between ISRU, life support systems, and Extra Vehicular Activity (EVA), applications will also be presented.

Recirculating 1-K-Pot for Pulse-Tube Cryostats

NASA Technical Reports Server (NTRS)

Paine, Christopher T.; Naylor, Bret J.; Prouve, Thomas

2013-01-01

A paper describes a 1-K-pot that works with a commercial pulse tube cooler for astrophysics instrumentation testbeds that require temperatures <1.7 K. Pumped liquid helium-4 cryostats were commonly used to achieve this temperature. However, liquid helium-4 cryostats are being replaced with cryostats using pulse tube coolers. The closed-cycle 1K-pot system for the pulse tube cooler requires a heat exchanger on the pulse tube, a flow restriction, pump-out line, and pump system that recirculates helium-4. The heat exchanger precools and liquefies helium- 4 gas at the 2.5 to 3.5 K pulse tube cold head. This closed-cycle 1-K-pot system was designed to work with commercially available laboratory pulse tube coolers. It was built using common laboratory equipment such as stainless steel tubing and a mechanical pump. The system is self-contained and requires only common wall power to operate. The lift of 15 mW at 1.1 K and base temperature of 0.97 K are provided continuously. The system can be scaled to higher heat lifts of .30 to 50 mW if desired. Ground-based telescopes could use this innovation to improve the efficiency of existing cryo

14 CFR 119.21 - Commercial operators engaged in intrastate common carriage and direct air carriers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Commercial operators engaged in intrastate common carriage and direct air carriers. 119.21 Section 119.21 Aeronautics and Space FEDERAL AVIATION...: CERTIFICATION AND OPERATIONS CERTIFICATION: AIR CARRIERS AND COMMERCIAL OPERATORS Applicability of Operating...

14 CFR 119.21 - Commercial operators engaged in intrastate common carriage and direct air carriers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Commercial operators engaged in intrastate common carriage and direct air carriers. 119.21 Section 119.21 Aeronautics and Space FEDERAL AVIATION...: CERTIFICATION AND OPERATIONS CERTIFICATION: AIR CARRIERS AND COMMERCIAL OPERATORS Applicability of Operating...

14 CFR 119.21 - Commercial operators engaged in intrastate common carriage and direct air carriers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Commercial operators engaged in intrastate common carriage and direct air carriers. 119.21 Section 119.21 Aeronautics and Space FEDERAL AVIATION...: CERTIFICATION AND OPERATIONS CERTIFICATION: AIR CARRIERS AND COMMERCIAL OPERATORS Applicability of Operating...

14 CFR 119.21 - Commercial operators engaged in intrastate common carriage and direct air carriers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Commercial operators engaged in intrastate common carriage and direct air carriers. 119.21 Section 119.21 Aeronautics and Space FEDERAL AVIATION...: CERTIFICATION AND OPERATIONS CERTIFICATION: AIR CARRIERS AND COMMERCIAL OPERATORS Applicability of Operating...

14 CFR 119.21 - Commercial operators engaged in intrastate common carriage and direct air carriers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Commercial operators engaged in intrastate common carriage and direct air carriers. 119.21 Section 119.21 Aeronautics and Space FEDERAL AVIATION...: CERTIFICATION AND OPERATIONS CERTIFICATION: AIR CARRIERS AND COMMERCIAL OPERATORS Applicability of Operating...

Reference Avionics Architecture for Lunar Surface Systems

NASA Technical Reports Server (NTRS)

Somervill, Kevin M.; Lapin, Jonathan C.; Schmidt, Oron L.

2010-01-01

Developing and delivering infrastructure capable of supporting long-term manned operations to the lunar surface has been a primary objective of the Constellation Program in the Exploration Systems Mission Directorate. Several concepts have been developed related to development and deployment lunar exploration vehicles and assets that provide critical functionality such as transportation, habitation, and communication, to name a few. Together, these systems perform complex safety-critical functions, largely dependent on avionics for control and behavior of system functions. These functions are implemented using interchangeable, modular avionics designed for lunar transit and lunar surface deployment. Systems are optimized towards reuse and commonality of form and interface and can be configured via software or component integration for special purpose applications. There are two core concepts in the reference avionics architecture described in this report. The first concept uses distributed, smart systems to manage complexity, simplify integration, and facilitate commonality. The second core concept is to employ extensive commonality between elements and subsystems. These two concepts are used in the context of developing reference designs for many lunar surface exploration vehicles and elements. These concepts are repeated constantly as architectural patterns in a conceptual architectural framework. This report describes the use of these architectural patterns in a reference avionics architecture for Lunar surface systems elements.

Shaping the operating room and perioperative systems of the future: innovating for improved competitiveness.

PubMed

Seim, Andreas R; Sandberg, Warren S

2010-12-01

To review the current state of anesthesiology for operative and invasive procedures, with an eye toward possible future states. Anesthesiology is at once a mature specialty and in a crisis--requiring breakthrough to move forward. The cost of care now approaches reimbursement, and outcomes as commonly measured approach perfection. Thus, the cost of further improvements seems ready to topple the field, just as the specialty is realizing that seemingly innocuous anesthetic choices have long-term consequences, and better practice is required. Anesthesiologists must create more headroom between costs and revenues in order to sustain the academic vigor and creativity required to create better clinical practice. We outline three areas in which technological and organizational innovation in anesthesiology can improve competitiveness and become a driving force in collaborative efforts to develop the operating rooms and perioperative systems of the future: increasing the profitability of operating rooms; increasing the efficiency of anesthesia; and technological and organizational innovation to foster improved patient flow, communication, coordination, and organizational learning.

Well-to-Wheels Analysis of Advanced Fuel/Vehicle Systems: A North American Study of Energy Use, Greenhouse Gas Emissions, and Criteria Pollutant Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brinkman, Norman; Wang, Michael; Weber, Trudy

An accurate assessment of future fuel/propulsion system options requires a complete vehicle fuel-cycle analysis, commonly called a well-to-wheels (WTW) analysis. This WTW study analyzes energy use and emissions associated with fuel production (or well-to-tank [WTT]) activities and energy use and emissions associated with vehicle operation (or tank-to-wheels [TTW]) activities.

Ultrascalable Techniques Applied to the Global Intelligence Community Information Awareness Common Operating Picture (IA COP)

DTIC Science & Technology

2005-11-01

more random. Autonomous systems can exchange entropy statistics for packet streams with no confidentiality concerns, potentially enabling timely and... analysis began with simulation results, which were validated by analysis of actual data from an Autonomous System (AS). A scale-free network is one...traffic—for example, time series of flux at given nodes and mean path length Outputs the time series from any node queried Calculates

Application of singular value decomposition to structural dynamics systems with constraints

NASA Technical Reports Server (NTRS)

Juang, J.-N.; Pinson, L. D.

1985-01-01

Singular value decomposition is used to construct a coordinate transformation for a linear dynamic system subject to linear, homogeneous constraint equations. The method is compared with two commonly used methods, namely classical Gaussian elimination and Walton-Steeves approach. Although the classical method requires fewer numerical operations, the singular value decomposition method is more accurate and convenient in eliminating the dependent coordinates. Numerical examples are presented to demonstrate the application of the method.

NASA's Automated Rendezvous and Docking/Capture Sensor Development and Its Applicability to the GER

NASA Technical Reports Server (NTRS)

Hinkel, Heather; Cryan, Scott; DSouza, Christopher; Strube, Matthew

2014-01-01

This paper will address how a common Automated Rendezvous and Docking/Capture (AR&D/C) sensor suite can support Global Exploration Roadmap (GER) missions, and discuss how the model of common capability development to support multiple missions can enable system capability level partnerships and further GER objectives. NASA has initiated efforts to develop AR&D/C sensors, that are directly applicable to GER. NASA needs AR&D/C sensors for both the robotic and crewed segments of the Asteroid Redirect Mission (ARM). NASA recently conducted a commonality assessment of the concept of operations for the robotic Asteroid Redirect Vehicle (ARV) and the crewed mission segment using the Orion crew vehicle. The commonality assessment also considered several future exploration and science missions requiring an AR&D/C capability. Missions considered were asteroid sample return, satellite servicing, and planetary entry, descent, and landing. This assessment determined that a common sensor suite consisting of one or more visible wavelength cameras, a three-dimensional LIDAR along with long-wavelength infrared cameras for robustness and situational awareness could be used on each mission to eliminate the cost of multiple sensor developments and qualifications. By choosing sensor parameters at build time instead of at design time and, without having to requalify flight hardware, a specific mission can design overlapping bearing, range, relative attitude, and position measurement availability to suit their mission requirements with minimal nonrecurring engineering costs. The resulting common sensor specification provides the union of all performance requirements for each mission and represents an improvement over the current systems used for AR&D/C today. NASA's AR&D/C sensor development path could benefit the International Exploration Coordination Group (ISECG) and support the GER mission scenario by providing a common sensor suite upon which GER objectives could be achieved while minimizing development costs. The paper will describe the concepts of operations of these missions and how the common sensors are utilized by each mission. It will also detail the potential partnerships and contribution of the International community in the development of this common AR&D/C sensor suite.

The optimization problems of CP operation

NASA Astrophysics Data System (ADS)

Kler, A. M.; Stepanova, E. L.; Maximov, A. S.

2017-11-01

The problem of enhancing energy and economic efficiency of CP is urgent indeed. One of the main methods for solving it is optimization of CP operation. To solve the optimization problems of CP operation, Energy Systems Institute, SB of RAS, has developed a software. The software makes it possible to make optimization calculations of CP operation. The software is based on the techniques and software tools of mathematical modeling and optimization of heat and power installations. Detailed mathematical models of new equipment have been developed in the work. They describe sufficiently accurately the processes that occur in the installations. The developed models include steam turbine models (based on the checking calculation) which take account of all steam turbine compartments and regeneration system. They also enable one to make calculations with regenerative heaters disconnected. The software for mathematical modeling of equipment and optimization of CP operation has been developed. It is based on the technique for optimization of CP operating conditions in the form of software tools and integrates them in the common user interface. The optimization of CP operation often generates the need to determine the minimum and maximum possible total useful electricity capacity of the plant at set heat loads of consumers, i.e. it is necessary to determine the interval on which the CP capacity may vary. The software has been applied to optimize the operating conditions of the Novo-Irkutskaya CP of JSC “Irkutskenergo”. The efficiency of operating condition optimization and the possibility for determination of CP energy characteristics that are necessary for optimization of power system operation are shown.

Screening reactor steam/water piping systems for water hammer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffith, P.

1997-09-01

A steam/water system possessing a certain combination of thermal, hydraulic and operational states, can, in certain geometries, lead to a steam bubble collapse induced water hammer. These states, operations, and geometries are identified. A procedure that can be used for identifying whether an unbuilt reactor system is prone to water hammer is proposed. For the most common water hammer, steam bubble collapse induced water hammer, six conditions must be met in order for one to occur. These are: (1) the pipe must be almost horizontal; (2) the subcooling must be greater than 20 C; (3) the L/D must be greatermore » than 24; (4) the velocity must be low enough so that the pipe does not run full, i.e., the Froude number must be less than one; (5) there should be void nearby; (6) the pressure must be high enough so that significant damage occurs, that is the pressure should be above 10 atmospheres. Recommendations on how to avoid this kind of water hammer in both the design and the operation of the reactor system are made.« less

Ion extraction capabilities of two-grid accelerator systems. M.S. Thesis

NASA Technical Reports Server (NTRS)

Rovang, D. C.; Wilbur, P. J.

1984-01-01

An experimental investigation into the ion extraction capabilities of two-grid accelerator systems common to electrostatic ion thrusters is described. This work resulted in a large body of experimental data which facilitates the selection of the accelerator system geometries and operating parameters necessary to maximize the extracted ion current. Results suggest that the impingement-limited perveance is not dramatically affected by reductions in screen hole diameter to 0.5 mm. Impingement-limited performance is shown to depend most strongly on grid separation distance, accelerator hole diameter ratio, the discharge-to-total accelerating voltage ratio, and the net-to-total accelerating voltage ratio. Results obtained at small grid separation ratios suggest a new grid operating condition where high beam current per hole levels are achieved at a specified net accelerating voltage. It is shown that this operating condition is realized at an optimum ratio of net-to-total accelerating voltage ratio which is typically quite high. The apparatus developed for this study is also shown to be well suited measuring the electron backstreaming and electrical breakdown characteristics of two-grid accelerator systems.

A Software Defined Radio Based Airplane Communication Navigation Simulation System

NASA Astrophysics Data System (ADS)

He, L.; Zhong, H. T.; Song, D.

2018-01-01

Radio communication and navigation system plays important role in ensuring the safety of civil airplane in flight. Function and performance should be tested before these systems are installed on-board. Conventionally, a set of transmitter and receiver are needed for each system, thus all the equipment occupy a lot of space and are high cost. In this paper, software defined radio technology is applied to design a common hardware communication and navigation ground simulation system, which can host multiple airplane systems with different operating frequency, such as HF, VHF, VOR, ILS, ADF, etc. We use a broadband analog frontend hardware platform, universal software radio peripheral (USRP), to transmit/receive signal of different frequency band. Software is compiled by LabVIEW on computer, which interfaces with USRP through Ethernet, and is responsible for communication and navigation signal processing and system control. An integrated testing system is established to perform functional test and performance verification of the simulation signal, which demonstrate the feasibility of our design. The system is a low-cost and common hardware platform for multiple airplane systems, which provide helpful reference for integrated avionics design.

Application of PMU-Based Information in the Indian Power System

NASA Astrophysics Data System (ADS)

Agarwal, P. K.; Agarwal, V. K.; Rathour, Harish

2013-05-01

SCADA/EMS system has been the most commonly used tool for real-time power system operation and control throughout the world. This system has been found to be very useful in steady-state analysis of the power system. The ever-increasing dependence of human society and every country's economy on electrical energy calls for reliable power delivery. In order to meet these expectations, engineers across the globe have been exploring such new technologies that can improve upon the limitations of SCADA and provide dynamic visibility of the power system. A breakthrough has now been achieved in the form of synchrophasor technology. Synchrophasor measurements using phasor measurement units (PMUs) deployed over a wide area, facilitate dynamic state measurement and visualization of a power system, which are useful in monitoring safety and security of the grid. The Power System Operation Corporation (POSOCO) has taken initiative and implemented a pilot project wherein nine phasor measurement units (PMUs) along with one phasor data concentrator (PDC) were commissioned in the Northern Region (NR) of India. The primary objective of this pilot project was to comprehend the synchrophasor technology and its applications in power system operation. The data received and information derived from the pilot project have been found to be very useful and helped in improving the performance of the grid operation in several ways. The pilot project is operational for the last two years; in the meanwhile, many other initiatives have also been taken in other regions by POSOCO. This article details the utilization of the data collected from the pilot projects and the application of the data in the improvement of Indian power grid.

One tool - one team: the marriage of test and operations in a low-budget spacecraft development

NASA Astrophysics Data System (ADS)

Finley, Charles J.

2006-05-01

The Air Force Research Laboratory's Space Vehicles Directorate (AFRL/VS) and the Department of Defense Space Test Program (STP) are two organizations that have partnered on more than 85 missions since 1968 to develop, launch, and operate Research and Development, Test and Evaluation space missions. As valuable as these missions have been to the follow-on generation of Operational systems, they are consistently under-funded and forced to execute on excessively ambitious development schedules. Due to these constraints, space mission development teams that serve the RDT&E community are faced with a number of unique technical and programmatic challenges. AFRL and STP have taken various approaches throughout the mission lifecycle to accelerate their development schedules, without sacrificing cost or system reliability. In the areas of test and operations, they currently employ one of two strategies. Historically, they have sought to avoid the added cost and complexity associated with coupled development schedules and segregated the spacecraft development and test effort from the ground operations system development and test effort. However, because these efforts have far more in common than they have differences, they have more recently attempted to pursue parallel I&T and Operations development and readiness efforts. This paper seeks to compare and contrast the "decoupled test and operations" approach, used by such missions as C/NOFS and Coriolis, with the "coupled test and operations" approach, adopted by the XSS-11 and TacSat-2 missions.

Introduction to Message-Bus Architectures for Space Systems

NASA Technical Reports Server (NTRS)

Smith, Dan; Gregory, Brian

2005-01-01

This course presents technical and programmatic information on the development of message-based architectures for space mission ground and flight software systems. Message-based architecture approaches provide many significant advantages over the more traditional socket-based one-of-a-kind integrated system development approaches. The course provides an overview of publish/subscribe concepts, the use of common isolation layer API's, approaches to message standardization, and other technical topics. Several examples of currently operational systems are discussed and possible changes to the system development process are presented. Benefits and lessons learned will be discussed and time for questions and answers will be provided.

Laboratory Ventilation and Safety.

ERIC Educational Resources Information Center

Steere, Norman V.

1965-01-01

In order to meet the needs of both safety and economy, laboratory ventilation systems must effectively remove air-borne toxic and flammable materials and at the same time exhaust a minimum volume of air. Laboratory hoods are the most commonly used means of removing gases, dusts, mists, vapors, and fumed from laboratory operations. To be effective,…

49 CFR 1242.77 - Administration (account XX-55-01).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Administration (account XX-55-01). 1242.77 Section...-Transportation § 1242.77 Administration (account XX-55-01). Separate common expenses in the same proportion as... systems operations and loss and damage claims processing (accounts XX-55-76, XX-55-77 and XX-55-78). ...