Electromagnetic compatibility of PLC adapters for in-home/domestic networks

NASA Astrophysics Data System (ADS)

Potisk, Lukas; Hallon, Jozef; Orgon, Milos; Fujdiak, Radek

2018-01-01

The use of programable logic controllers (PLC) technology in electrical networks 230 V causes electromagnetic radiation that interferes with other electrical equipment connected to the network [1-4]. Therefore, this article describes the issues of electromagnetic compatibility (EMC) of new PLC adapters used in IP broadband services in a multi-user environment. The measurements of disturbing electromagnetic field originated in PLC adapters were made in a certified laboratory EMC (laboratory of electromagnetic compatibility) in the Institute of Electrical Engineering at Faculty of Electrical Engineering and Information Technology of the Slovak University of Technology in Bratislava. The measured spectra of the radiated electromagnetic field will be compared with the results obtained when testing older PLC modems [5].

Elimination of Potential Electrical Stress During EMC (CS01) Testing

NASA Technical Reports Server (NTRS)

Erickson, Kenneth P.; Whittlesey, Albert C.; Vorperian, Vatche

2006-01-01

This viewgraph presentation reviews possible ways to eliminate electrical stress during Electromagneticic Compatibility (EMC) testing. The presentation reviews tests that have had problems due to electrical stress. On December 5, 1995 Cassini Radar instrument failed a functional test in preparation for EMC conducted susceptibility (CSO 1 ) testing. The instrument power supply did not turn on as required, and failure occurred prior to injection of CS test stimulus. A investigation of the failure was conducted. A PSPICE simulation of Cassini Radar 30V line using the EMC test setup was performed; the result of the simulation was an oscillation on the 30V input of the power supply. In another case: on December 28, 1999 an oscillation occurred on the input power line of the SlRTF Infrared Array Camera (IRAC) while preparing to perform CSOI testing, Resulted in damage to flight hardware. Subsequent to failure, JPL provided GSFC history and corrective action from Cassini Radar CSOI test failure GSFC implemented the same corrective action as JPL, except that the value of the resistor connected across the isolation transformer primary winding is 2.5 ohms instead of 50 ohms. Three recommendations are made: (1) Make EMC test community aware of the problem and potential solutions by presenting papers at major environmental test conferences (2) Include warnings and safeguards in EMC test requirements and procedures (3) Try to convince EMC test equipment suppliers to design a CSOl test fixture similar to fixture shown in the diagram

Development of automated electromagnetic compatibility test facilities at Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Harrison, Cecil A.

1986-01-01

The efforts to automate the electromagentic compatibility (EMC) test facilites at Marshall Flight Center were examined. A battery of nine standard tests is to be integrated by means of a desktop computer-controller in order to provide near real-time data assessment, store the data acquired during testing on flexible disk, and provide computer production of the certification report.

Electromagnetic Compatibility between Marine Automatic Identification and Public Correspondence Systems in the Maritime Mobile VHF Band.

DOT National Transportation Integrated Search

2000-04-01

The Coast Guard funded the National Telecommunications and Information Administration : (NTIA) to perform electromagnetic compatibility (EMC) tests between an ITU-R M. 825-3 : (Characteristics Of a Transponder System Using Digital Selective Calling T...

Electromagnetic Compatibility (EMC) for Integration and Use of Near Field Communication (NFC) in Aircraft

NASA Astrophysics Data System (ADS)

Nalbantoglu, Cemal; Kiehl, Thorsten; God, Ralf; Stadtler, Thiemo; Kebel, Robert; Bienert, Renke

2016-05-01

For portable electronic devices (PEDs), e.g. smartphones or tablets, near field communication (NFC) enables easy and convenient man-machine interaction by simply tapping a PED to a tangible NFC user interface. Usage of NFC technology in the air transport system is supposed to facilitate travel processes and self-services for passengers and to support digital interaction with other participating stakeholders. One of the potential obstacles to benefit from NFC technology in the aircraft cabin is the lack of an explicit qualification guideline for electromagnetic compatibility (EMC) testing. In this paper, we propose a methodology for EMC testing and for characterizing NFC devices and their emissions according to aircraft industry standards (RTCA DO-160, DO-294, DO-307 and EUROCAE ED- 130). A potential back-door coupling scenario of radiated NFC emissions and possible effects to nearby aircraft wiring are discussed. A potential front-door- coupling effect on NAV/COM equipment is not investigated in this paper.

Morgantown People Mover Electromagnetic Compatibility Program

DOT National Transportation Integrated Search

1980-09-01

Electromagnetic Compatibility (EMC) of a transit system is the absence of interference between all parts of the system, and between the system and the community which it serves. This report documents the EMC experience obtained during the design and ...

Correlating the EMC analysis and testing methods for space systems in MIL-STD-1541A

NASA Technical Reports Server (NTRS)

Perez, Reinaldo J.

1990-01-01

A study was conducted to improve the correlation between the electromagnetic compatibility (EMC) analysis models stated in MIL-STD-1541A and the suggested testing methods used for space systems. The test and analysis methods outlined in MIL-STD-1541A are described, and a comparative assessment of testing and analysis techniques as they relate to several EMC areas is presented. Suggestions on present analysis and test methods are introduced to harmonize and bring the analysis and testing tools in MIL-STD-1541A into closer agreement. It is suggested that test procedures in MIL-STD-1541A must be improved by providing alternatives to the present use of shielded enclosures as the primary site for such tests. In addition, the alternate use of anechoic chambers and open field test sites must be considered.

C3I system modification and EMC (electromagnetic compatibility) methodology, volume 1

NASA Astrophysics Data System (ADS)

Wilson, J. L.; Jolly, M. B.

1984-01-01

A methodology (i.e., consistent set of procedures) for assessing the electromagnetic compatibility (EMC) of RF subsystem modifications on C3I aircraft was generated during this study (Volume 1). An IEMCAP (Intrasystem Electromagnetic Compatibility Analysis Program) database for the E-3A (AWACS) C3I aircraft RF subsystem was extracted to support the design of the EMC assessment methodology (Volume 2). Mock modifications were performed on the E-3A database to assess, using a preliminary form of the methodology, the resulting EMC impact. Application of the preliminary assessment methodology to modifications in the E-3A database served to fine tune the form of a final assessment methodology. The resulting final assessment methodology is documented in this report in conjunction with the overall study goals, procedures, and database. It is recommended that a similar EMC assessment methodology be developed for the power subsystem within C3I aircraft. It is further recommended that future EMC assessment methodologies be developed around expert systems (i.e., computer intelligent agents) to control both the excruciating detail and user requirement for transparency.

EMC Test Challenges for NASAs James Webb Space Telescope

NASA Technical Reports Server (NTRS)

McCloskey, John

2016-01-01

This presentation describes the electromagnetic compatibility (EMC) tests performed on the Integrated Science Instrument Module (ISIM), the science payload of the James Webb Space Telescope (JWST), at NASAs Goddard Space Flight Center (GSFC) in August 2015. By its very nature of being an integrated payload, it could be treated as neither a unit level test nor an integrated spacecraft observatory test. Non-standard test criteria are described along with non-standard test methods that had to be developed in order to evaluate them. Results are presented to demonstrate that all test criteria were met in less than the time allocated.

EMC Test Challenges for NASA's James Webb Space Telescope

NASA Technical Reports Server (NTRS)

McCloskey, John

2016-01-01

This presentation describes the electromagnetic compatibility (EMC) tests performed on the Integrated Science Instrument Module (ISIM), the science payload of the James Webb Space Telescope (JWST), at NASAs Goddard Space Flight Center (GSFC) in August 2015. By its very nature of being an integrated payload, it could be treated as neither a unit level test nor an integrated spacecraft observatory test. Non-standard test criteria are described along with non-standard test methods that had to be developed in order to evaluate them. Results are presented to demonstrate that all test criteria were met in less than the time allocated.

Feasibility results of an electromagnetic compatibility test protocol to evaluate medical devices to radio frequency identification exposure

PubMed Central

2014-01-01

Background The use of radio frequency identification (RFID) systems in healthcare is increasing, and concerns for electromagnetic compatibility (EMC) pose one of the biggest obstacles for widespread adoption. Numerous studies have demonstrated that RFID systems can interfere with medical devices; however, the majority of past studies relied on time-consuming and burdensome test schemes based on ad hoc test methods applied to individual RFID systems. Methods This paper presents the results of using an RFID simulator that allows for faster evaluation of RFID-medical device EMC against a library of RFID test signals at various field strengths. Results The results of these tests demonstrate the feasibility and adequacy of simulator testing and can be used to support its incorporation into applicable consensus standards. Conclusions This work can aid the medical device community in better assessing the risks associated with medical device exposure to RFID. PMID:25086451

Feasibility results of an electromagnetic compatibility test protocol to evaluate medical devices to radio frequency identification exposure.

PubMed

Seidman, Seth J; Bekdash, Omar; Guag, Joshua; Mehryar, Maryam; Booth, Paul; Frisch, Paul

2014-08-03

The use of radio frequency identification (RFID) systems in healthcare is increasing, and concerns for electromagnetic compatibility (EMC) pose one of the biggest obstacles for widespread adoption. Numerous studies have demonstrated that RFID systems can interfere with medical devices; however, the majority of past studies relied on time-consuming and burdensome test schemes based on ad hoc test methods applied to individual RFID systems. This paper presents the results of using an RFID simulator that allows for faster evaluation of RFID-medical device EMC against a library of RFID test signals at various field strengths. The results of these tests demonstrate the feasibility and adequacy of simulator testing and can be used to support its incorporation into applicable consensus standards. This work can aid the medical device community in better assessing the risks associated with medical device exposure to RFID.

Development of Design Standards and Guidelines for Electromagnetic Compatibility and Lightning Protection for Spacecraft Utilizing Composite Materials

NASA Technical Reports Server (NTRS)

1996-01-01

Preliminary design guidelines necessary to assure electromagnetic compatibility (EMC) of spacecraft using composite materials, are presented. A database of electrical properties of composite materials which may have an effect on EMC is established. The guidelines concentrate on the composites that are conductive but may require enhancement to be adequate for EMC purposes. These composites are represented by graphite reinforced polymers. Methods for determining adequate conductivity levels for various EMC purposes are defined, along with the methods of design which increase conductivity of composite materials and joints to adequate levels.

Electromagnetic Compatibility (EMC) in Microelectronics.

DTIC Science & Technology

1983-02-01

Fault Tree Analysis", System Saftey Symposium, June 8-9, 1965, Seattle: The Boeing Company . 12. Fussell, J.B., "Fault Tree Analysis-Concepts and...procedure for assessing EMC in microelectronics and for applying DD, 1473 EOiTO OP I, NOV6 IS OESOL.ETE UNCLASSIFIED SECURITY CLASSIFICATION OF THIS...CRITERIA 2.1 Background 2 2.2 The Probabilistic Nature of EMC 2 2.3 The Probabilistic Approach 5 2.4 The Compatibility Factor 6 3 APPLYING PROBABILISTIC

The Ships Below-Decks Electromagnetic Compatibility (EMC) Program. A compilation of Papers Presented at the 1987 IEEE International Symposium on EMC

DTIC Science & Technology

1987-09-30

were producing below-deck environ - such that after 24 hours the performance loss ranged mental levels exceeding the "normal" environmental from 13 to...SGA performance environmental EMI testing in the electromagnetically measurements b- made in the laboratory. However, it quiet laboratory environments ... Environmentally Sealed SGAs.................................... 1-1 Need for Long Term SGA Performance Evaluation .................... 1-2 Performance

Electromagnetic Interference/Compatibility (EMI/EMC) Control Test and Measurement Facility: User Test Planning Guide

NASA Technical Reports Server (NTRS)

Scully, Robert C.

2011-01-01

Test process, milestones and inputs are unknowns to first-time users of the EMI/EMC Test Facility. The User Test Planning Guide aids in establishing expectations for both NASA and non-NASA facility customers. The potential audience for this guide includes both internal and commercial spaceflight hardware/software developers. It is intended to assist their test engineering personnel in test planning and execution. Material covered includes a roadmap of the test process, roles and responsibilities of facility and user, major milestones, facility capabilities, and inputs required by the facility. Samples of deliverables, test article interfaces, and inputs necessary to define test scope, cost, and schedule are included as an appendix to the guide.

Aircraft electromagnetic compatibility

NASA Technical Reports Server (NTRS)

Clarke, Clifton A.; Larsen, William E.

1987-01-01

Illustrated are aircraft architecture, electromagnetic interference environments, electromagnetic compatibility protection techniques, program specifications, tasks, and verification and validation procedures. The environment of 400 Hz power, electrical transients, and radio frequency fields are portrayed and related to thresholds of avionics electronics. Five layers of protection for avionics are defined. Recognition is given to some present day electromagnetic compatibility weaknesses and issues which serve to reemphasize the importance of EMC verification of equipment and parts, and their ultimate EMC validation on the aircraft. Proven standards of grounding, bonding, shielding, wiring, and packaging are laid out to help provide a foundation for a comprehensive approach to successful future aircraft design and an understanding of cost effective EMC in an aircraft setting.

Electromagnetic compatibility (EMC) standard test chamber upgrade requirements for spacecraft design verification tests

NASA Technical Reports Server (NTRS)

Dyer, Edward F.

1992-01-01

In view of the serious performance deficiencies inherent in conventional modular and welded shielding EMC test enclosures, in which multipath reflections and resonant standing waves can damage flight hardware during RF susceptibility tests, NASA-Goddard has undertaken the modification of a 20 x 24 ft modular-shielded enclosure through installation of steel panels to which ferrite tiles will be mounted with epoxy. The internally reflected RF energy will thereby be absorbed, and exterior power-line noise will be reduced. Isolation of power-line filters and control of 60-Hz ground connections will also be undertaken in the course of upgrading.

EMC (Electromagnetic Compatibility) Standards Handbook. Revision 4,

DTIC Science & Technology

1982-11-01

report was prepared by the lIT Research Institute as part of AF Project 649E under Contract F-19628-80-C-0042 with the Electronic Systems Division of...the Air Pbrce Systems Command in support of the DoD Electromagnetic Compatibility Analysis Center, Annapolis, Maryland. This report has been reviewed...3-1 "JVDE Organizations .. .0 . . . . . . . . . . . . . . . . . . . . . 3 1 VDE Testing Station

Electromagnetic environmental criteria for US Army missile systems - EMC, EMR, EMI, EMP, ESD, and lightning

NASA Astrophysics Data System (ADS)

Ponds, Charles D.; Knaur, James A.

1988-01-01

This paper presents the design and test requirements in developing an electromagnetic compatibility missile system. Environmental levels are presented for electromagnetic radiation hazards, electromagnetic radiation operational, electrostatic discharge, lightning, and electromagnetic pulse (nuclear). Testing techniques and facility capabilities are presented for research and development testing of missile systems.

Overview on the standardization in the field of electromagnetic compatibility

NASA Astrophysics Data System (ADS)

Goldberg, Georges

1989-04-01

Standardization in the domain of electromagnetic compatibility (EMC) is discussed, with specific reference to the standards of the International Electrotechnical Commission, the Comite International Special des Perturbations Radioelectriques, and the Comite Europeen de Normalisation Electrotechnique. EMC fields considered include radiocommunications, telecommunications, biological effects, and data transmission. Standards are presented for such electromagnetic disturbances as low-frequency, high-frequency, conduction, and radiation phenomena.

International Symposium on Electromagnetic Compatibility, Wakefield, MA, August 20-22, 1985, Record

NASA Astrophysics Data System (ADS)

Various papers on electromagnetic compatibility are presented. The general topics addressed include: EMI transient/impulsive disturbances, electromagnetic shielding, antennas and propagation, measurement technology, anechoic chamber/open site measurements, communications systems, electrostatic discahrge, cables/transmission lines. Also considered are: elecromagnetic environments, antennas, electromagnetic pulse, nonlinear effect, computer/data transmission systems, EMI standards and requirements, enclosures/TEM cells, systems EMC, and test site measurements.

EMC Enhanced Constant ’Z’ Modulator.

DTIC Science & Technology

1984-06-01

TUTHILL, Colonel, USAF Chief, Relilability & Compatibility Division FOR THE COMMANDER: JOHN A. RITZ Acting Chief, Plans Office 0 * - If your address...supply bypasses. 3.2.6 System Testing Breadboard system tests resulted in the replacement of the HP5082-3340 shunt mounted PIN diodes due to a carrer life

21 CFR 874.3305 - Wireless air-conduction hearing aid.

Code of Federal Regulations, 2013 CFR

2013-04-01

...-amplifying device, intended to compensate for impaired hearing that incorporates wireless technology in its...: (1) Appropriate analysis/testing should validate electro magnetic compatibility (EMC) and safety of... technology functions; and (3) Labeling should specify appropriate instructions, warnings, and information...

Wireless Coexistence and EMC of Bluetooth and 802.11b Devices in Controlled Laboratory Settings

PubMed Central

Seidman, Seth; Kainz, Wolfgang; Ruggera, Paul; Mendoza, Gonzalo

2011-01-01

This paper presents experimental testing that has been performed on wireless communication devices as victims of electromagnetic interference (EMI). Wireless victims included universal serial bus (USB) network adapters and personal digital assistants (PDAs) equipped with IEEE 802.11b and Bluetooth technologies. The experimental data in this paper was gathered in an anechoic chamber and a gigahertz transverse electromagnetic (GTEM) cell to ensure reliable and repeatable results. This testing includes: Electromagnetic compatibility (EMC) testing performed in accordance with IEC 60601-1-2, an in-band sweep of EMC testing, and coexistence testing. The tests in this study show that a Bluetooth communication was able to coexist with other Bluetooth devices with no decrease in throughput and no communication breakdowns. However, testing revealed a significant decrease in throughput and increase in communication breakdowns when an 802.11b source is near an 802.11b victim. In a hospital setting decreased throughput and communication breakdowns can cause wireless medical devices to fail. It is therefore vital to have an understanding of the effect EMI can have on wireless communication devices. PMID:22043254

Wireless Coexistence and EMC of Bluetooth and 802.11b Devices in Controlled Laboratory Settings.

PubMed

Seidman, Seth; Kainz, Wolfgang; Ruggera, Paul; Mendoza, Gonzalo

2011-01-01

This paper presents experimental testing that has been performed on wireless communication devices as victims of electromagnetic interference (EMI). Wireless victims included universal serial bus (USB) network adapters and personal digital assistants (PDAs) equipped with IEEE 802.11b and Bluetooth technologies. The experimental data in this paper was gathered in an anechoic chamber and a gigahertz transverse electromagnetic (GTEM) cell to ensure reliable and repeatable results. This testing includes: Electromagnetic compatibility (EMC) testing performed in accordance with IEC 60601-1-2, an in-band sweep of EMC testing, and coexistence testing. The tests in this study show that a Bluetooth communication was able to coexist with other Bluetooth devices with no decrease in throughput and no communication breakdowns. However, testing revealed a significant decrease in throughput and increase in communication breakdowns when an 802.11b source is near an 802.11b victim. In a hospital setting decreased throughput and communication breakdowns can cause wireless medical devices to fail. It is therefore vital to have an understanding of the effect EMI can have on wireless communication devices.

EMC system test performance on Spacelab

NASA Astrophysics Data System (ADS)

Schwan, F.

1982-07-01

Electromagnetic compatibility testing of the Spacelab engineering model is discussed. Documentation, test procedures (including data monitoring and test configuration set up) and performance assessment approach are described. Equipment was assembled into selected representative flight configurations. The physical and functional interfaces between the subsystems were demonstrated within the integration and test sequence which culminated in the flyable configuration Long Module plus one Pallet.

Space and Missile Systems Center Standard: Test Requirements for Ground Systems

DTIC Science & Technology

2013-09-30

Human Exposure to Radio Frequency Electromagnetic Fields , 3kHz to...5] Federal Code of Regulations FCC Part 15 Federal Code of Regulations, Title 47: Telecommunication, Part 15– Radio Frequency Devices 2.3 Non...DT&E Development test and evaluation EMC Electromagnetic compatibility FAT Factory acceptance test FCA Functional configuration audit FCC

Potential Damage to Flight Hardware from MIL-STD-462 CS02 Setup

NASA Technical Reports Server (NTRS)

Harris, Patrick K.; Block, Nathan F.

2003-01-01

The MIL-STD-462 CS02 conducted susceptibility test setup includes an audio transformer, with the secondary used as an inductor, and a large capacitor. Together, these two components form an L-type low-pass filter to minimize the injected test signal input into the power source. Some flight hardware power input configurations are not compatible with this setup and break into oscillation when powered up. This, in turn, can damage flight hardware. Such an oscillation resulted in the catastrophic failure of an item tested in the Goddard Space Flight Center (GSFC) Large electromagnetic compatibility (EMC) Test Facility.

UMTA Rail Transit EMI/EMC Program : An Overview and Summary

DOT National Transportation Integrated Search

1987-02-01

This report gives a history of the UMTA Rail Transit Electromagnetic Interference and Electromagnetic Compatibility (EMI/EMC) program, together with a listing of significant achievements over the life of the program. This is the lead volume of a nine...

Electromagnetic Compatibility Design of the Computer Circuits

NASA Astrophysics Data System (ADS)

Zitai, Hong

2018-02-01

Computers and the Internet have gradually penetrated into every aspect of people’s daily work. But with the improvement of electronic equipment as well as electrical system, the electromagnetic environment becomes much more complex. Electromagnetic interference has become an important factor to hinder the normal operation of electronic equipment. In order to analyse the computer circuit compatible with the electromagnetic compatibility, this paper starts from the computer electromagnetic and the conception of electromagnetic compatibility. And then, through the analysis of the main circuit and system of computer electromagnetic compatibility problems, we can design the computer circuits in term of electromagnetic compatibility. Finally, the basic contents and methods of EMC test are expounded in order to ensure the electromagnetic compatibility of equipment.

Experimental investigations and guidelines for PCB design for a fuel injection ECU to meet automotive environmental, EMI/EMC and ESD standards

NASA Astrophysics Data System (ADS)

Kalyankar-Narwade, Supriya; Kumar, C. Ramesh; Patil, Sanjay A.

2017-11-01

Engine Management ECU plays a vital role in controlling different important features related to the engine performance. ECU is an embedded system which includes hardware and firmware platform for control logics. However, it is necessary to verify its smooth performance by its functionality testing in the Electromagnetic environment for approval. If these requirements are not known at earlier stages, then ECU may not fulfil functional requirements during required automotive electronic test standards. Hence, focusing on EMS ECU, this paper highlights hardware, layout and software guidelines for solving problems related with Electromagnetic Interference (EMI) to comply ISO 7637, CISPR 25 standard, Electromagnetic Compatibility (EMC) to comply ISO 11452-4,5 standard, Electrostatic Discharge (ESD) to comply ISO 10605 standard and Environmental Testing to comply standards as per IEC standards. This paper specifies initially the importance, need and guidelines for reducing the EMI effect on PCB i.e. making ECU more electromagnetically compatible as per automotive standards. The guidelines are useful for the designers to avoid pitfalls at the later stage. After mentioned modifications in the paper, ECU successfully passed the requirements for all standard tests.

Radiated EMC immunity investigation of common recognition identification platform for medical applications

NASA Astrophysics Data System (ADS)

Miranda, Jorge; Cabral, Jorge; Ravelo, Blaise; Wagner, Stefan; Pedersen, Christian F.; Memon, Mukhtiar; Mathiesen, Morten

2015-01-01

An innovative e-healthcare platform named common recognition and identification platform (CRIP) was developed and tested as part of the CareStore project. CareStore and CRIP aims at delivering accurate and safe disease management by minimising human operator errors in hospitals and care facilities. To support this, the CRIP platform features fingerprint biometrics and near field communication (NFC) for user identification; and Bluetooth communication support for a range of telemedicine medical devices adhering to the IEEE 11073 standard. The aim of this study was to evaluate the electromagnetic compatibility (EMC) immunity of the CRIP platform in order to validate it for medical application use. The first prototype of CRIP was demonstrated to operate as expected by showing the user identification function feasibility, both via NFC and biometric, and by detection of Bluetooth devices via radio frequency (RF) scanning. The NFC module works in the 13.56 MHz band and the Bluetooth module work in the 2.4 GHz band, according to the IEEE 802.15.1 standard. The standard test qualification of the CRIP was performed based on the radiated EMC immunity with respect to the EN 61000-4-3 standard. The immunity tests were conducted under industrial EMC compliance with electric field aggression, with levels up to 10 V/m in both horizontal and vertical polarisations when the test antenna and the CRIP were placed at a distance of 3 m. It was found that the CRIP device complies with the European electromagnetic (EM) radiation immunity requirements.

Small Diameter Bomb Increment II (SDB II)

DTIC Science & Technology

2013-12-01

in 2013: Electromagnetic Environments and Effects and Hazards of Electromagnetic Radiation to Ordnance . Reliability Growth Testing started in June...unclassified c. THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 SDB II December 2013 SAR April 16, 2014 17:24:29...Framework EMC - Electromagnetic Compatibility EMI - Electromagnetic Interference GESP - GIG Enterprise Service Profiles GIG - Global Information Grid i.e

Basic EMC (Electromagnetic Compatibility) Technology Advancement for C3 Systems - Model Revision for IEMCAP (Intrasystem Electromagnetic Compatibility Analysis Program).

DTIC Science & Technology

1984-10-01

8217:- . . . .:- . . . * *. . - . . -’" - *. - . " . * - -A REFERENCES [1] J. L. Bogdanor , et. al., Intrasystem Electromagnetic Compatibility Analy- sis Program, Technical Report, RADC-TR-74...286, Vol. IV A, Rome Air -.- Development Center, Griffiss AFB, NY, November 1982. [30] J0 B. Bogdanor , M. D. Siegel, G. L. Weinstock, Intra-Vehicle

Hardware Demonstration: Radiated Emissions as a Function of Common Mode Current

NASA Technical Reports Server (NTRS)

Mc Closkey, John; Roberts, Jen

2016-01-01

This presentation describes the electromagnetic compatibility (EMC) tests performed on the Integrated Science Instrument Module (ISIM), the science payload of the James Webb Space Telescope (JWST), at NASAs Goddard Space Flight Center (GSFC) in August 2015. By its very nature of being an integrated payload, it could be treated as neither a unit level test nor an integrated spacecraft observatory test. Non-standard test criteria are described along with non-standard test methods that had to be developed in order to evaluate them. Results are presented to demonstrate that all test criteria were met in less than the time allocated.

Technical Basis for Electromagnetic Compatibility Regulatory Guidance Update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ewing, Paul D.; Korsah, Kofi; Harrison, Thomas J.

2016-03-01

The objective of this report is to serve as the technical basis document for the next, planned revision of this RG that highlights and provides the rationale for the recommended changes. The structure of this document follows and summarizes the several assessment activities undertaken during the course of this project to evaluate new and updated electromagnetic compatibility (EMC) standards, testing methods and limits, and relevant technology developments being incorporated into plant activities that may have EMI/RFI implications, as well as other specific issues, including impacts of electrostatic discharge (ESD) on safety equipment and impacts on increased usage of wireless devicesmore » in nuclear power plants.« less

20 kHz main inverter unit. [for space station power supplies

NASA Technical Reports Server (NTRS)

Hussey, S.

1989-01-01

A proof-of-concept main inverter unit has demonstrated the operation of a pulse-width-modulated parallel resonant power stage topology as a 20-kHz ac power source driver, showing simple output regulation, parallel operation, power sharing and short-circuit operation. The use of a two-stage dc input filter controls the electromagnetic compatibility (EMC) characteristics of the dc power bus, and the use of an ac harmonic trap controls the EMC characteristics of the 20-kHz ac power bus.

Characteristics of the wire biconical antenna used for EMC measurements

NASA Astrophysics Data System (ADS)

Austin, Brian A.; Fourie, Andre P. C.

1991-08-01

The characteristics of a wire biconical antenna that determine its antenna factor were computed by using the method of moments code NEC-2. A fairly extensive validation exercise was conducted from which a suitable computer model was derived. The input impedance, gain, and radiation patterns of the antenna were computed for special cases where the biconical antenna is used above a conducting ground plane for open-field EMC (electromagnetic compatibility) testing. The effects of height above the ground plane and polarization of the antenna on these parameters were found and the antenna factor was corrected for them. The current distribution along the antenna elements was also examined, and it was found that significant pattern distortion can occur at some frequencies when a horizontal wire biconical antenna is used close to the ground. These results will allow this broadband antenna to be used with confidence in applications where previously only resonant dipoles were specified.

Primary experimental study on safety of deep brain stimulation in RF electromagnetic field.

PubMed

Jun, Xu; Luming, Li; Hongwei, Hao

2009-01-01

With the rapid growth of clinical application of Deep Brain Stimulation, its safety and functional concern in the electromagnetic field, another pollution becoming much more serious, has become more and more significant. Meanwhile, the measuring standards on Electromagnetic Compatibility (EMC) for DBS are still incomplete. Particularly, the knowledge of the electromagnetic field induced signals on the implanted lead is ignorant while some informal reports some side effects. This paper briefly surmised the status of EMC standards on implantable medical devices. Based on the EMC experiments of DBS device we developed, two experiments for measuring the induced voltage of the deep brain stimulator in RF electromagnetic field were reported. The measured data showed that the induced voltage in some frequency was prominent, for example over 2V. As a primary research, we think these results would be significant to cause researcher to pay more attention to the EMC safety problem and biological effects of the induced voltage in deep brain stimulation and other implantable devices.

Definition and test of the electromagnetic immunity of UAS for first responders

NASA Astrophysics Data System (ADS)

Adami, C.; Chmel, S.; Jöster, M.; Pusch, T.; Suhrke, M.

2015-11-01

Recent technological developments considerably lowered the barrier for unmanned aerial systems (UAS) to be employed in a variety of usage scenarios, comprising live video transmission from otherwise inaccessible vantage points. As an example, in the French-German ANCHORS project several UAS guided by swarm intelligence provide aerial views and environmental data of a disaster site while deploying an ad-hoc communication network for first responders. Since being able to operate in harsh environmental conditions is a key feature, the immunity of the UAS against radio frequency (RF) exposure has been studied. Conventional Electromagnetic Compatibility (EMC) applied to commercial and industrial electronics is not sufficient since UAS are airborne and can as such move beyond the bounds within which RF exposure is usually limited by regulatory measures. Therefore, the EMC requirements have been complemented by a set of specific RF test frequencies and parameters where strong sources are expected to interfere in the example project test case of an inland port environment. While no essential malfunctions could be observed up to field strengths of 30 V m-1, a sophisticated, more exhaustive approach for testing against potential sources of interference in key scenarios of UAS usage should be derived from our present findings.

Lecture Series on Electromagnetic Interference and Electromagnetic Compatibility Presented on 10-11 June 1991 in Kjeller, Norway, 13-14 June 1991 in Konigswinter, Germany and 17-18 June 1991 in Lisbon, Portugal.

DTIC Science & Technology

1991-06-01

assessing EMC characteristics of EM systems in a lecture on "Measuremazzenvironments and testing".The various test en - vronments available will be described...severe in a dual-diversity system gains at least 10 dB in SNR relative to a maritime situation where salt water corrosion has for many non-diversity...environment having great significance for NATO systems are: (a) electromagnetic interference (EMT) arising from both natural and man-made sources; (b

System Guidelines for EMC Safety-Critical Circuits: Design, Selection, and Margin Demonstration

NASA Technical Reports Server (NTRS)

Lawton, R. M.

1996-01-01

Demonstration of required safety margins on critical electrical/electronic circuits in large complex systems has become an implementation and cost problem. These margins are the difference between the activation level of the circuit and the electrical noise on the circuit in the actual operating environment. This document discusses the origin of the requirement and gives a detailed process flow for the identification of the system electromagnetic compatibility (EMC) critical circuit list. The process flow discusses the roles of engineering disciplines such as systems engineering, safety, and EMC. Design and analysis guidelines are provided to assist the designer in assuring the system design has a high probability of meeting the margin requirements. Examples of approaches used on actual programs (Skylab and Space Shuttle Solid Rocket Booster) are provided to show how variations of the approach can be used successfully.

Shuttle Communications and Tracking, Avionics, and Electromagnetic Compatibility

NASA Technical Reports Server (NTRS)

deSilva, K.; Hwu, Shian; Kindt, Kaylene; Kroll, Quin; Nuss, Ray; Romero, Denise; Schuler, Diana; Sham, Catherine; Scully, Robert

2011-01-01

By definition, electromagnetic compatibility (EMC) is the capability of components, sub-systems, and systems, to operate in their intended electromagnetic environment, within an established margin of safety, and at design levels of performance. Practice of the discipline itself incorporates knowledge of various aspects of applied physics, materials science, and engineering across the board, and includes control and mitigation of undesirable electromagnetic interaction between intentional and unintentional emitters and receivers of radio frequency energy, both within and external to the vehicle; identification and control of the hazards of non-ionizing electromagnetic radiation to personnel, ordnance, and fuels and propellants; and vehicle and system protection from the direct and indirect effects of lightning and various other forms of electrostatic discharge (ESD) threats, such as triboelectrification and plasma charging. EMC is extremely complex and far-reaching, affecting in some degree every aspect of the vehicle s design and operation. The most successful efforts incorporate EMC design features and techniques throughout design and fabrication of the vehicle s structure and components, as well as appropriate operational considerations with regard to electromagnetic threats in the operational environment, from the beginning of the design effort to the end of the life cycle of the manufactured product. This approach yields the highest design performance with the lowest cost and schedule impact.

Military Handbook. Grounding, Bonding, and Shielding for Electronic Equipments and Facilities. Volume 2. Applications

DTIC Science & Technology

1987-12-29

EMC, San Francisco CA, 16-18 July 1974, 76-84. 1-13. E. R. Uhlig, "Developmnent of Criteria for Protection ef NIKE -X Power Plant and Facilities...Interference Reduction and Electronic Compatibility, Armour Research Foundation of Illinois Institute of Technology (now IITRI), Chicago IL, October...Measuring Systems Susceptibility," Proceedings of the Eighth Tri-Service Conference on Electromagnetic Compatibility, Armour Research Foundation of

System Guidelines for EMC Safety-Critical Circuits: Design, Selection, and Margin Demonstration

NASA Technical Reports Server (NTRS)

Lawton, R. M.

1996-01-01

Demonstration of safety margins for critical points (circuits) has traditionally been required since it first became a part of systems-level Electromagnetic Compatibility (EMC) requirements of MIL-E-6051C. The goal of this document is to present cost-effective guidelines for ensuring adequate Electromagnetic Effects (EME) safety margins on spacecraft critical circuits. It is for the use of NASA and other government agencies and their contractors to prevent loss of life, loss of spacecraft, or unacceptable degradation. This document provides practical definition and treatment guidance to contain costs within affordable limits.

Electromagnetic compatibility (EMC) assurance of automotive signal/data transmission for vehicle transportation systems.

DOT National Transportation Integrated Search

2012-03-31

This report is the final report of the Center for Transportation & Materials Engineering (CTME) research project funded by the grant (Grant Number: G00000245). The report is submitted to Director of CTME for partial fulfillment for the deliverables o...

Electromagnetic Compatibility for the Space Shuttle

NASA Technical Reports Server (NTRS)

Scully, Robert C.

2004-01-01

This slide presentation reviews the Space Shuttle electromagnetic compatibility (EMC). It includes an overview of the design of the shuttle with the areas that are of concern for the electromagnetic compatibility. It includes discussion of classical electromagnetic interference (EMI) and the work performed to control the electromagnetic interference. Another area of interest is electrostatic charging and the threat of electrostatic discharge and the attempts to reduce damage to the Shuttle from these possible hazards. The issue of electrical bonding is als reviewed. Lastly the presentation reviews the work performed to protect the shuttle from lightning, both in flight and on the ground.

Electromagnetic Compatibility Testing Studies

NASA Technical Reports Server (NTRS)

Trost, Thomas F.; Mitra, Atindra K.

1996-01-01

This report discusses the results on analytical models and measurement and simulation of statistical properties from a study of microwave reverberation (mode-stirred) chambers performed at Texas Tech University. Two analytical models of power transfer vs. frequency in a chamber, one for antenna-to-antenna transfer and the other for antenna to D-dot sensor, were experimentally validated in our chamber. Two examples are presented of the measurement and calculation of chamber Q, one for each of the models. Measurements of EM power density validate a theoretical probability distribution on and away from the chamber walls and also yield a distribution with larger standard deviation at frequencies below the range of validity of the theory. Measurements of EM power density at pairs of points which validate a theoretical spatial correlation function on the chamber walls and also yield a correlation function with larger correlation length, R(sub corr), at frequencies below the range of validity of the theory. A numerical simulation, employing a rectangular cavity with a moving wall shows agreement with the measurements. The determination that the lowest frequency at which the theoretical spatial correlation function is valid in our chamber is considerably higher than the lowest frequency recommended by current guidelines for utilizing reverberation chambers in EMC testing. Two suggestions have been made for future studies related to EMC testing.

A Real-Time Knowledge Based Expert System For Diagnostic Problem Solving

NASA Astrophysics Data System (ADS)

Esteva, Juan C.; Reynolds, Robert G.

1986-03-01

This paper is a preliminary report of a real-time expert system which is concerned with the detection and diagnosis of electrical deviations in on-board vehicle-based electrical systems. The target systems are being tested at radio frequencies to evaluate their capability to be operated at designed levels of efficiency in an electromagnetic environment. The measurement of this capability is known as ElectroMagnetic Compatibility (EMC). The Intelligent Deviation Diagnosis (IDD) system consists of two basic modules the Automatic Data Acquisition Module (ADAM) and the Diagnosis System (DS). In this paper only the diagnosis system is described.

Developing energy and momentum conceptual survey (EMCS) with four-tier diagnostic test items

NASA Astrophysics Data System (ADS)

Afif, Nur Faadhilah; Nugraha, Muhammad Gina; Samsudin, Achmad

2017-05-01

Students' conceptions of work and energy are important to support the learning process in the classroom. For that reason, a diagnostic test instrument is needed to diagnose students' conception of work and energy. As a result, the researcher decided to develop Energy and Momentum Conceptual Survey (EMCS) instrument test into four-tier test diagnostic items. The purpose of this research is organized as the first step of four-tier test-formatted EMCS development as one of diagnostic test instruments on work and Energy. The research method used the 4D model (Defining, Designing, Developing and Disseminating). The instrument developed has been tested to 39 students in one of Senior High Schools. The resulting research showed that four-tier test-formatted EMCS is able to diagnose students' conception level of work and energy concept. It can be concluded that the development of four-tier test-formatted EMCS is one of potential diagnostic test instruments that able to obtain the category of students who understand concepts, misconceptions and do not understand about Work and Energy concept at all.

Electromagnetic Compatibility Analysis Group VA-H3

NASA Technical Reports Server (NTRS)

Armanda, Carlos A.

2008-01-01

During the eight weeks working at NASA, I was fortunate enough to work with the Expendable Launch Vehicle's (ELV) Electromagnetic Compatibility (EMC) Team, who is responsible for the evaluation and analysis of any EMI risk an ELV mission might face. This group of people concern themselves with practically any form of electromagnetic interference that may risk the safety of a rocket, a mission, or even people. Taking this into consideration, the group investigates natural forms of interference, such as lightning, to manmade interferences, such as antennas.

Reverberant Microwave Propagation

DTIC Science & Technology

2008-10-01

HERO Hazards of Electromagnetic Radiation to Ordnance HP Hewlett Packard HWD Half-Wave Dipole IEC International Electrotechnical Commission IEE...composite panels used in new ship design; Hazards of Electromagnetic Radiation to Ordnance ( HERO ) analyses; and digital wireless system performance...Electro-Explosive Device EMC Electromagnetic Compatibility ft Foot (feet) GHz Gigahertz HERO Hazards of Electromagnetic

Investigation of Electromagnetic Signatures of a FPGA Using an APREL EM-ISIGHT System

DTIC Science & Technology

2015-12-01

unprofessional workmanship in the bonding process. Focused ion beam (FIB) images often consist of some type of etch and/or deposition of material from/to...characteristics of conducted emissions." Electromagnetic Compatibility, 2008. EMC 2008. IEEE International Symposium (2008): 1-4. Montanari, Ivan

Achieving EMC Emissions Compliance for an Aeronautics Power Line Communications System

NASA Astrophysics Data System (ADS)

Dominiak, S.; Vos, G.; ter Meer, T.; Widmer, H.

2012-05-01

Transmitting data over the power distribution network - Power Line Communications (PLC) -provides an interesting solution to reducing the weight and complexity of wiring networks in commercial aircraft. One of the potential roadblocks for the introduction of this technology is achieving EMC emissions compliance. In this article an overview of the EMC conducted and radiated emissions testing for PLC- enabled aeronautics equipment is presented. Anomalies resulting from chamber resonances leading to discrepancies between the conducted emissions tests and the measured radiated emissions are identified and described. Measurements made according to the current version of the civil aeronautical EMC standard, EUROCAE ED-14F (RTCA DO-160F), show that PLC equipment can achieve full EMC emissions compliance.

Comparative analyses of different variants of standard ground for automatic control systems of technical processes of oil and gas production

NASA Astrophysics Data System (ADS)

Gromakov, E. I.; Gazizov, A. T.; Lukin, V. P.; Chimrov, A. V.

2017-01-01

The paper analyses efficiency (interference resistance) of standard TT, TN, IT networks in control links of automatic control systems (ACS) of technical processes (TP) of oil and gas production. Electromagnetic compatibility (EMC) is a standard term used to describe the interference in grounding circuits. Improved EMC of ACS TP can significantly reduce risks and costs of malfunction of equipment that could have serious consequences. It has been proved that an IT network is the best type of grounds for protection of ACS TP in real life conditions. It allows reducing the interference down to the level that is stated in standards of oil and gas companies.

Instrumentation and test methods of an automated radiated susceptibility system

NASA Astrophysics Data System (ADS)

Howard, M. W.; Deere, J.

1983-09-01

The instrumentation and test methods of an automated electromagnetic compatibility (EMC) system for performing radiated susceptibility tests from 14 kHz to 1000 MHz is described. Particular emphasis is given to the effectiveness of the system in the evaluation of electronic circuits for susceptibility to RF radiation. The system consists of a centralized data acquisition/control unit which interfaces with the equipment under test (EUT), the RF isolated field probes, and RF amplifier ALC output; four broadband linear RF amplifiers; and a frequency synthesizer with drive level increments in steps of 0.1 dB. Centralized control of the susceptibility test system is provided by a desktop computer. It is found that the system can reduce the execution time of RF susceptibility tests by as much as 70 percent. A block diagram of the system is provided.

Assessment of risks of EMI for personal medical electronic devices (PMEDs) from emissions of millimeter-wave security screening systems

NASA Astrophysics Data System (ADS)

Witters, Donald; Bassen, Howard; Guag, Joshua; Addissie, Bisrat; LaSorte, Nickolas; Rafai, Hazem

2013-06-01

This paper describes research and testing of a representative group of high priority body worn and implantable personal medical electronic devices (PMEDs) for exposure to millimeter wave (MMW) advanced imaging technology (AIT) security systems used at airports. The sample PMEDs included in this study were implantable cardiac pacemakers, ICDs, neurostimulators and insulin pumps. These PMEDs are designed and tested for susceptibility to electromagnetic interference (EMI) under the present standards for medical device electromagnetic compatibility (EMC). However, the present standards for medical equipment do not address exposure to the much higher frequency fields that are emitted by MMW security systems. Initial AIT emissions measurements were performed to assess the PMED and passenger exposures. Testing protocols were developed and testing methods were tailored to the type of PMED. In addition, a novel exposure simulation system was developed to allow controlled EMC testing without the need of the MMW AIT system. Methodology, test results, and analysis are presented, along with an assessment of the human exposure and risks for PMED users. The results on this study reveal no effects on the medical devices from the exposure to the MMW security system. Furthermore, the human exposure measurements and analysis showed levels well below applicable standard, and the risks for PMED users and others we assessed to be very low. These findings apply to the types of PMEDs used in the study though these findings might suggest that the risks for other, similar PMEDs would likely be similar.

Basic EMC Technology Advancement for C3 Systems - Model Revision for IEMCAP. Volume 5

DTIC Science & Technology

1984-10-01

important asset. 126 REFERENCES [1] J. L. Bogdanor , et. al., Inttasystem Electromagnetic Compatibility Analy- sis Program, Technical Report, RADC-TR-74...Method of Moments, Technical Report, RADC-TR-82-286, Vol. IV A, Rome Air Development Center, Griffiss AFB, NY, November 1982. [30] J. B. Bogdanor , M. D

Galileo environmental test and analysis program summary

NASA Technical Reports Server (NTRS)

Hoffman, A. R.

1991-01-01

This paper presents an overview of the Galileo Project's environmental test and analysis program during the spacecraft development phase - October 1978 through launch in October 1989. After describing the top-level objectives of the program, summaries of-the approach, requirements, and margins are provided. Examples of assembly- and system-level test results are given for both the pre-1986 (direct mission) testing and the post-1986 (Venus-Earth-Earth gravity assist mission) testing, including dynamic, thermal, electromagnetic compatibility (EMC), and magnetic. The approaches and results for verifying by analysis that the requirements of certain environments (e.g., radiation, micrometeoroids, and single event upsets) are satisfied are presented. The environmental program implemented on Galileo satisfied the spirit and intent of the requirements imposed by the Project during the spacecraft's development. The lessons learned from the Galileo environmental program are discussed in this paper.

Application of nomographs for analysis and prediction of receiver spurious response EMI

NASA Astrophysics Data System (ADS)

Heather, F. W.

1985-07-01

Spurious response EMI for the front end of a superheterodyne receiver follows a simple mathematic formula; however, the application of the formula to predict test frequencies produces more data than can be evaluated. An analysis technique has been developed to graphically depict all receiver spurious responses usig a nomograph and to permit selection of optimum test frequencies. The discussion includes the math model used to simulate a superheterodyne receiver, the implementation of the model in the computer program, the approach to test frequency selection, interpretation of the nomographs, analysis and prediction of receiver spurious response EMI from the nomographs, and application of the nomographs. In addition, figures are provided of sample applications. This EMI analysis and prediction technique greatly improves the Electromagnetic Compatibility (EMC) test engineer's ability to visualize the scope of receiver spurious response EMI testing and optimize test frequency selection.

Novel device for creating continuous curvilinear capsulorhexis.

PubMed

Soylak, Mustafa

2016-01-01

The purpose of this paper is to develop a novel capsulorhexis system. Mechatronics Laboratory, University of Erciyes and Kayseri Maya Eye Hospital. A 3D model was created and simulations were conducted to develop a new device which was designed, fabricated and tested for continuous curvilinear capsulorhexis (CCC). The name of this system is the electro-mechanical capsulorhexis system (EMCS). The 3D model was created by using a commercial design software and a 3D printer was used to fabricate the EMCS Finite element analysis and geometrical relation tests of the EMCS for different sized lenses were performed. The results show that the EMCS is a perfect solution for capsulorhexis surgeries, without mechanical or geometrical problems. The EMCS can open the anterior lens capsule more easily and effectively than manual CCC applications and needs less experience.

Developments in the application of the geometrical theory of diffraction and computer graphics to aircraft inter-antenna coupling analysis

NASA Astrophysics Data System (ADS)

Bogusz, Michael

1993-01-01

The need for a systematic methodology for the analysis of aircraft electromagnetic compatibility (EMC) problems is examined. The available computer aids used in aircraft EMC analysis are assessed and a theoretical basis is established for the complex algorithms which identify and quantify electromagnetic interactions. An overview is presented of one particularly well established aircraft antenna to antenna EMC analysis code, the Aircraft Inter-Antenna Propagation with Graphics (AAPG) Version 07 software. The specific new algorithms created to compute cone geodesics and their associated path losses and to graph the physical coupling path are discussed. These algorithms are validated against basic principles. Loss computations apply the uniform geometrical theory of diffraction and are subsequently compared to measurement data. The increased modelling and analysis capabilities of the newly developed AAPG Version 09 are compared to those of Version 07. Several models of real aircraft, namely the Electronic Systems Trainer Challenger, are generated and provided as a basis for this preliminary comparative assessment. Issues such as software reliability, algorithm stability, and quality of hardcopy output are also discussed.

Cross-reactive antibodies in convalescent SARS patients' sera against the emerging novel human coronavirus EMC (2012) by both immunofluorescent and neutralizing antibody tests.

PubMed

Chan, Kwok-Hung; Chan, Jasper Fuk-Woo; Tse, Herman; Chen, Honglin; Lau, Candy Choi-Yi; Cai, Jian-Piao; Tsang, Alan Ka-Lun; Xiao, Xincai; To, Kelvin Kai-Wang; Lau, Susanna Kar-Pui; Woo, Patrick Chiu-Yat; Zheng, Bo-Jiang; Wang, Ming; Yuen, Kwok-Yung

2013-08-01

A severe acute respiratory syndrome (SARS)-like disease due to a novel betacoronavirus, human coronavirus EMC (HCoV-EMC), has emerged recently. HCoV-EMC is phylogenetically closely related to Tylonycteris-bat-coronavirus-HKU4 and Pipistrellus-bat-coronavirus-HKU5 in Hong Kong. We conducted a seroprevalence study on archived sera from 94 game-food animal handlers at a wild life market, 28 SARS patients, and 152 healthy blood donors in Southern China to assess the zoonotic potential and evidence for intrusion of HCoV-EMC and related viruses into humans. Anti-HCoV-EMC and anti-SARS-CoV antibodies were detected using screening indirect immunofluorescence (IF) and confirmatory neutralizing antibody tests. Two (2.1%) animal handlers had IF antibody titer of ≥ 1:20 against both HCoV-EMC and SARS-CoV with neutralizing antibody titer of <1:10. No blood donor had antibody against either virus. Surprisingly, 17/28 (60.7%) of SARS patients had significant IF antibody titers with 7/28 (25%) having anti-HCoV-EMC neutralizing antibodies at low titers which significantly correlated with that of HCoV-OC43. Bioinformatics analysis demonstrated a significant B-cell epitope overlapping the heptad repeat-2 region of Spike protein. Virulence of SARS-CoV over other betacoronaviruses may boost cross-reactive neutralizing antibodies against other betacoronaviruses. Convalescent SARS sera may contain cross-reactive antibodies against other betacoronaviruses and confound seroprevalence study for HCoV-EMC. Copyright © 2013 The British Infection Association. Published by Elsevier Ltd. All rights reserved.

Plant growth using EMCS hardware on the ISS.

PubMed

Iversen, Tor-Henning; Fossum, Knut R; Svare, Hakon; Johnsson, Anders; Schiller, Peter

2002-07-01

Under separate contracts with ESA (FUMO and ERM Study) and as a link in the development of the European Modular Cultivation System's (EMCS) functionality and biocompatibility, plant studies have been performed at The Plant Biocentre in Trondheim, Norway. The main goal was to test whether the breadboards containing the major components planned for use in the EMCS would be optimal for space experiments with plant material. The test plans and the experimental set-up for the verification of biocompatibility and biological functionality included the use of a few model plant species including cress (Lepidium sativum L.) and Arabidopsis thaliana. The plants were tested at different developmental levels of morphological and physiological complexity (illumination, life support, humidity control, water supply, observation, short- and long-term plant growth experiments and contamination prevention). Results from the tests show that the EMCS concept is useful for long duration plant growth on the ISS.

Radiated Emissions from a Remote-Controlled Airplane-Measured in a Reverberation Chamber

NASA Technical Reports Server (NTRS)

Ely, Jay J.; Koppen, Sandra V.; Nguyen, Truong X.; Dudley, Kenneth L.; Szatkowski, George N.; Quach, Cuong C.; Vazquez, Sixto L.; Mielnik, John J.; Hogge, Edward F.; Hill, Boyd L.;

Overview of the Orion Vibroacoustic Test Capability at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Hughes, William O.; Hozman, Aron D.; McNelis, Mark E.; Otten, Kim D.

2008-01-01

In order to support the environmental test needs for our new Orion and Constellation program, NASA is developing unique world-class test facilities. To optimize this testing of spaceflight hardware while minimizing transportation issues, a one-stop, under one roof test capability is being developed at the Space Power Facility at the NASA Glenn Research Center's Plum Brook Station. This facility will provide the capability to perform the following environmental testing: (1) reverberation acoustic testing, (2) mechanical base-shake sine testing, (3) modal testing, (4) thermal-vacuum testing, and (5) EMI/EMC (electromagnetic interference and compatibility) testing. An overview of this test capability will be provided in this presentation, with special focus on the two new vibroacoustic test facilities currently being designed and built, the Reverberant Acoustic Test Facility (RATF) and the Mechanical Vibration Facility (MVF). Testing of the engineering developmental hardware and qualification hardware of the Orion (Crew Exploration Vehicle) will commence shortly after the facilities are commissioned.

Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Test Report, Electromagnetic Interference (EMI)/Electromagnetic Radiation(EMR) and Electromagnetic Capability (EMC) for the EOS/AMSU-A1

NASA Technical Reports Server (NTRS)

Paliwoda, L.

1998-01-01

This document contains the procedure and the test results of the Advanced Microwave Sounding Unit-A (AMSU-A) Earth Observing System (EOS) Project, assembly part number 1356008-1, serial number 202, Electromagnetic Interference (EMI) and Electromagnetic Susceptibility (EMC) qualification test. The test was conducted in accordance with the approved EMI/EMC Test Plan/Procedure, Specification number AE-26151/8B, dated 10 September 1998. Aerojet intends that the presentation and submittal of this document, prepared in accordance with the objectives established by the aforementioned Test Plan/Procedure, document number AE-26151/8B, will satisfy the data requirement with respect to the AMSU-A/EOS instrument operational compliance of the EMI/EMC test requirement. Test for the AMSU-A/EOS instrument have been completed and all the requirements per General Interface Requirement Document (GIRD), GSFC 422-11-12-01, for EOS Common Spacecraft/Instruments, paragraph 10.11, were met with the exceptions of the test methods CE03, RE01, and RE02, as described in this document.

Suppression of radiating harmonics Electro-Impulse Deicing (EIDI) systems

NASA Astrophysics Data System (ADS)

Zieve, Peter; Ng, James; Fiedberg, Robert

1991-10-01

The electromagnetic compatibility (EMC) of two different configurations of electromagnetic deicing systems is discussed. Both Electro-Impulse Deicing (EIDI) and Eddy Current Repulsion Deicing Strip (EDS) are investigated. With EIDI, rigid coils are mounted behind the wing; while with EDS, the impulse coils are built thin and flexible with printed circuit board technology. An important consideration in the certification of electromagnetic impulse deicing systems is electromagnetic compatibility (EMC). When the capacitor bank discharges, a large current pulse travels down a transmission line to the coil. The coil is one source of radiation. Another source is the cabling and connections to the coil. In work conducted for the FAA in 1988, it was found that excessive electromagnetic emissions resulted from the operation of a Low Voltage Electro-Impulse Deicer (LVEID) in conjunction with a composite wing. The goal of this project was to investigate and develop techniques for controlling emissions without the benefit of shielding. In this study it was determined that both EIDI and EDS could be brought within the RTCA/DO-160B standards through proper shielding and termination of the pulse power cable. An alternative topology of EDS with the impulse coil on the wing exterior surface did not meet the standard.

EMI / EMC Design for Class D Payloads (Resource Prospector / NIRVSS)

NASA Technical Reports Server (NTRS)

Forgione, Josh; Benton, Joshua Eric; Thompson, Sarah; Colaprete, Anthony

2015-01-01

EMI/EMC techniques are applied to a Class D instrument (NIRVSS) to achieve low noise performance and reduce risk of EMI/EMC testing failures and/or issues during system integration and test. Basic techniques are not terribly expensive or complex, but do require close coordination between electrical and mechanical staff early in the design process. Low-cost methods to test subsystems on the bench without renting an EMI chamber are discussed. This method was applied to the NIRVSS instrument and achieved improvements up to 59dB on conducted emissions measurements between hardware revisions.

Measurement technology of RF interference current in high current system

NASA Astrophysics Data System (ADS)

Zhao, Zhihua; Li, Jianxuan; Zhang, Xiangming; Zhang, Lei

2018-06-01

Current probe is a detection method commonly used in electromagnetic compatibility. With the development of power electronics technology, the power level of power conversion devices is constantly increasing, and the power current of the electric energy conversion device in the electromagnetic launch system can reach 10kA. Current probe conventionally used in EMC (electromagnetic compatibility) detection cannot meet the test requirements on high current system due to the magnetic saturation problem. The conventional high current sensor is also not suitable for the RF (Radio Frequency) interference current measurement in high current power device due to the high noise level in the output of active amplifier. In this paper, a passive flexible current probe based on Rogowski coil and matching resistance is proposed that can withstand high current and has low noise level, to solve the measurement problems of interference current in high current power converter. And both differential mode and common mode current detection can be easily carried out with the proposed probe because of the probe's flexible structure.

Adhoc electromagnetic compatibility testing of non-implantable medical devices and radio frequency identification

PubMed Central

2013-01-01

Background The use of radiofrequency identification (RFID) in healthcare is increasing and concerns for electromagnetic compatibility (EMC) pose one of the biggest obstacles for widespread adoption. Numerous studies have documented that RFID can interfere with medical devices. The majority of past studies have concentrated on implantable medical devices such as implantable pacemakers and implantable cardioverter defibrillators (ICDs). This study examined EMC between RFID systems and non-implantable medical devices. Methods Medical devices were exposed to 19 different RFID readers and one RFID active tag. The RFID systems used covered 5 different frequency bands: 125–134 kHz (low frequency (LF)); 13.56 MHz (high frequency (HF)); 433 MHz; 915 MHz (ultra high frequency (UHF])) and 2.4 GHz. We tested three syringe pumps, three infusion pumps, four automatic external defibrillators (AEDs), and one ventilator. The testing procedure is modified from American National Standards Institute (ANSI) C63.18, Recommended Practice for an On-Site, Ad Hoc Test Method for Estimating Radiated Electromagnetic Immunity of Medical Devices to Specific Radio-Frequency Transmitters. Results For syringe pumps, we observed electromagnetic interference (EMI) during 13 of 60 experiments (22%) at a maximum distance of 59 cm. For infusion pumps, we observed EMI during 10 of 60 experiments (17%) at a maximum distance of 136 cm. For AEDs, we observed EMI during 18 of 75 experiments (24%) at a maximum distance of 51 cm. The majority of the EMI observed was classified as probably clinically significant or left the device inoperable. No EMI was observed for all medical devices tested during exposure to 433 MHz (two readers, one active tag) or 2.4 GHz RFID (two readers). Conclusion Testing confirms that RFID has the ability to interfere with critical medical equipment. Hospital staff should be aware of the potential for medical device EMI caused by RFID systems and should be encouraged to perform on-site RF immunity tests prior to RFID system deployment or prior to placing new medical devices in an RFID environment. The methods presented in this paper are time-consuming and burdensome and suggest the need for standard test methods for assessing the immunity of medical devices to RFID systems. PMID:23845013

Adhoc electromagnetic compatibility testing of non-implantable medical devices and radio frequency identification.

PubMed

Seidman, Seth J; Guag, Joshua W

2013-07-11

The use of radiofrequency identification (RFID) in healthcare is increasing and concerns for electromagnetic compatibility (EMC) pose one of the biggest obstacles for widespread adoption. Numerous studies have documented that RFID can interfere with medical devices. The majority of past studies have concentrated on implantable medical devices such as implantable pacemakers and implantable cardioverter defibrillators (ICDs). This study examined EMC between RFID systems and non-implantable medical devices. Medical devices were exposed to 19 different RFID readers and one RFID active tag. The RFID systems used covered 5 different frequency bands: 125-134 kHz (low frequency (LF)); 13.56 MHz (high frequency (HF)); 433 MHz; 915 MHz (ultra high frequency (UHF])) and 2.4 GHz. We tested three syringe pumps, three infusion pumps, four automatic external defibrillators (AEDs), and one ventilator. The testing procedure is modified from American National Standards Institute (ANSI) C63.18, Recommended Practice for an On-Site, Ad Hoc Test Method for Estimating Radiated Electromagnetic Immunity of Medical Devices to Specific Radio-Frequency Transmitters. For syringe pumps, we observed electromagnetic interference (EMI) during 13 of 60 experiments (22%) at a maximum distance of 59 cm. For infusion pumps, we observed EMI during 10 of 60 experiments (17%) at a maximum distance of 136 cm. For AEDs, we observed EMI during 18 of 75 experiments (24%) at a maximum distance of 51 cm. The majority of the EMI observed was classified as probably clinically significant or left the device inoperable. No EMI was observed for all medical devices tested during exposure to 433 MHz (two readers, one active tag) or 2.4 GHz RFID (two readers). Testing confirms that RFID has the ability to interfere with critical medical equipment. Hospital staff should be aware of the potential for medical device EMI caused by RFID systems and should be encouraged to perform on-site RF immunity tests prior to RFID system deployment or prior to placing new medical devices in an RFID environment. The methods presented in this paper are time-consuming and burdensome and suggest the need for standard test methods for assessing the immunity of medical devices to RFID systems.

Encapsulation of ethylhexyl methoxycinnamate, a light-sensitive UV filter, in lipid nanoparticles.

PubMed

Durand, L; Habran, N; Henschel, V; Amighi, K

2010-01-01

The aim of this study was to encapsulate ethylhexyl methoxycinnamate (EMC), a commonly used UVB filter, in a solid lipid matrix in order to obtain microparticles and then nanoparticles to reduce its photo-instability under UV light exposure. Glyceryl behenate, rice bran wax and ozokerite were investigated for encapsulating EMC. The suspensions of nanoparticles contained 70% encapsulated EMC (relative to the lipid mass). The absorbance level at 310 nm of suspensions containing nanoparticles was more than twice that of those containing microparticles. So, decreasing the size of particles improved the efficiency of light protection, regardless of the lipid material used. Moreover, free EMC presented a 30% loss of its efficiency after 2 h of irradiation, whereas the three NLC formulations showed a loss of absorbency between 10% and 21%. The in vitro cutaneous penetration test did not show a higher potential penetration for EMC contained in nanosuspensions compared to free EMC.

Summary of the electromagnetic compatibility evaluation of the proposed satellite power system

NASA Technical Reports Server (NTRS)

Morrison, E. L., Jr.; Grant, W. B.; Davis, K. C.

1980-01-01

The effects of the proposed solar power satellite (SPS) operations on electronic equipment and systems by fundamental, harmonic, and intermodulation component emissions from the orbital station; and the fundamental, harmonic, and structural intermodulation emissions from the rectenna site were evaluated. The coupling and affects interactions affecting a wide spectrum of electronic equipment are considered. The primary EMC tasking areas are each discussed separately.

Computational Electromagnetics Application to Small Geometric Anomalies and Associated Ucertainty Evaluation

DTIC Science & Technology

2010-02-28

implemented a fast method to enable the statistical characterization of electromagnetic interference and compatibility (EMI/EMC) phenomena on electrically...higher accuracy is needed, e.g., to compute higher moment statistics . To address this problem, we have developed adaptive stochastic collocation methods ...SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) AF OFFICE OF SCIENTIFIC RESEARCH 875 N. RANDOLPH ST. ROOM 3112 ARLINGTON VA 22203 UA

Electromagnetic Noise Interference and Compatibility

DTIC Science & Technology

1975-11-01

RADIO INTERFERENCE by C.Fengler 7 LES CHARGES ELECTROSTATIQUES ET LES PERTURBATIONS QU’ELLES ENTRAINENT DANS LES LIAISONS RADIOELECTRIQUES par...PAR LA TRANSMISSION DANS UN SYSTFJE INTEGRE AEROPORTE par r,.David et M.Vanneizel 31 Not available at time of priating Reference DIGITAL DATA...TRANSMISSION IN AIRCRAFT: EMC-PROBLEMS AND POSSIBLE SOLUTIONS by R.Rode 32 GENERATIONS El EFFETS DES TENSIONS PARASITES DE CONDUCTION ET DE RAVONNEMENT ENTRE

Development of models simulating operation of elements of radio devices, for solving problems of ensuring electromagnetic compatibility of radio electronic means

NASA Astrophysics Data System (ADS)

Glotov, V. V.; Ostroumov, I. V.; Romashchenko, M. A.

2018-05-01

To study the effect of phase-shift signals parameters on EMC of REM, a generalized signal generation model in a radio transmitter was developed which allows obtaining digital representations of phase-shift signals, which are a continuous pulse in the time domain and on the frequency axis with different signal element envelope shapes.

Maintaining Stability During a Conducted-Ripple EMC Test

NASA Technical Reports Server (NTRS)

Vorperian, Vatche

2007-01-01

An improved technique, and electronic circuitry to implement the technique, have been developed for a military-standard electromagnetic-compatibility (EMC) test in which one analyzes susceptibility to low-frequency ripple conducted into the equipment under test via a DC power line. In the traditional technique for performing the particular test, the ripple is coupled onto the DC power line via a transformer. Depending upon some design details of the equipment under test, the inductance of the transformer can contribute a degree of instability that results in an oscillation of amplitude large enough to destroy the equipment. It is usually possible to suppress the oscillation by connecting a damping resistor to the primary terminals of the ripple-injection transformer. However, it is important to emphasize the usually in the preceding sentence: sometimes, the resistive damping becomes insufficient to suppress destructive oscillation. In addition, undesirably, the resistor contributes to power dissipation and power demand, and thereby also necessitates the use of a larger ripple voltage amplifier. Yet another disadvantage of the transformer-coupling technique is that the transformer introduces low-frequency distortion of the injected ripple voltage. The improved technique makes it possible to inject ripple with very low distortion at low frequency, without inducing oscillation. In this technique, a transformer is not used: Instead, power is fed to the equipment under test via series power field-effect transistors (FETs) controlled by a summing operational amplifier. One of the inputs to the amplifier controls the DC component of the power-line voltage; the other input, generated by an external oscillator, controls the ripple component. The circuitry for implementing this technique includes panel displays, an internal power supply for the operational amplifier and panel displays, and amplitude controls for the DC and ripple powerline voltage components.

Endometrial cells on Pap tests: ideal reporting is more complex than just finding the right age.

PubMed

Fischer, Gabor; Haddad, Maha; Cormier, Karen

2017-07-01

The age for reporting normal endometrial cells (EMCs) on Pap tests was changed to ≥ 45 years in the latest Bethesda update (2014). This recommendation is solely based on age with no consensus on optimal reporting guidelines. Pap tests with EMCs for women ≥40 years were retrieved from our Laboratory Information System (LIS). Patient age, last menstrual period (LMP) and available follow-up histology were recorded. Follow-up diagnoses were categorized as: no significant pathology, benign, hyperplasia ± atypia, or malignant. The Fisher's exact test was used to assess the association between categorical variables, p < .05 (two-sided test) was considered significant. Of the 352 cases with EMCs, 155 had surgical follow-up. They showed no malignancy in the 89 women between 40-49 years, compared with five malignancies in the 66 women 50+ years (p = .016). The number of cases with significant pathology (hyperplasia and malignant) was 4 (40-49 years) vs. 11 (50+ years) (p = 0.029). The LMP was inconsistently provided (57%) and women identified as postmenopausal on requisition comprised all the malignancies and half the hyperplasias. Combined effort by pathologists and clinicians necessitates determining the best standardized clinicopathologic guidelines to report EMCs and appropriate follow-up. Increasing the required age to ≥50 years would provide more optimal patient management; however, there are other considerations beyond age. Reporting EMCs in postmenopausal women is a reasonable alternative requiring consistent and accurate recording of LMP. Improving provided information for pathologists, determining reporting requirements for EMCs and standardizing clinical follow-up should be a multidisciplinary effort. Diagn. Cytopathol. 2017;45:587-591. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

EMCS Experiment Container for the Plant Gravity Perception Experiment

NASA Image and Video Library

2018-02-08

iss054e037079 (Feb. 8, 2018) --- Plant Gravity Perception experiment in a centrifuge on a European Modular Cultivation System (EMCS) Experiment Container (EC) to test the gravity-sensing ability of plants in microgravity.

EMCS EC Connector Inspection Imagery

NASA Image and Video Library

2018-02-02

iss054e026863 (Feb. 2, 2018) --- The Plant Gravity Perception experiment in a centrifuge before its second run on the European Modular Cultivation System (EMCS) Experiment Container (EC) to test the gravity-sensing ability of plants in microgravity.

Electronic media communication with friends from 2002 to 2006 and links to face-to-face contacts in adolescence: an HBSC study in 31 European and North American countries and regions.

PubMed

Kuntsche, Emmanuel; Simons-Morton, Bruce; ter Bogt, Tom; Queija, Inmaculada Sánchez; Tinoco, Victoria Muñoz; Gaspar de Matos, Margarida; Santinello, Massimo; Lenzi, Michela

2009-09-01

Because the potential for electronic media communication (EMC) has increased greatly, it is of interest to describe trends in EMC between adolescents and their friends and to investigate whether EMC facilitate or supersede face-to-face contacts among peers. Answers of 275,571 adolescents concerning contacting friends by means of the phone, text messages, and the internet (i. e. EMC), the number of close friends, and the number of afternoons and evenings per week spent out with friends were analysed by means of chi(2)-tests and multiple regression. In 2006, between more than one third (11-year olds) and nearly two thirds (15-year olds) communicated electronically with their friends daily or nearly daily. From 2002 to 2006, EMC increased in almost all participating countries. Particularly high increases were found in Eastern Europe. Across countries, the higher the frequency of EMC the higher the number of afternoons and evenings spent with friends. The results are surprisingly consistent across the 31 countries and suggest that EMC among adolescents facilitate rather than supersede face-to-face peer contacts.

Basic EMC (Electromagnetic Compatibility) Technology Advancement for C3 Systems. Volume 1B. Demodulation Radio Frequency Interference Effects in Operational Amplifier Circuits.

DTIC Science & Technology

1985-02-01

Then it follows that H2 (fl,-f 2) (-flf Thus, the total amplitude of the intermodulation signal at fre- quency fAF is given by6 V = V +I mA2 III(fl 1-f...RFI suppression in the manner described. 229 . * . ... ..... 4 -*.-., ,e ’ - ."..~ REFERENCES 1. G. Kaplan , "Computer Aided Design," IEEE Spectrum, Vol

EMCS Experiment Container Replacement

NASA Image and Video Library

2018-01-26

iss054e023800 (Jan. 26, 2018) --- NASA astronaut Joe Acaba placing an Experiment Container (EC) on the European Modular Cultivation System (EMCS) for the the first run of the Plant Gravity Perception experiment to test the gravity-sensing ability of plants in microgravity.

EMCS Experiment Container Replacement

NASA Image and Video Library

2018-01-26

iss054e023776 (Jan. 26, 2018) --- NASA astronaut Joe Acaba removing an Experiment Container (EC) on the European Modular Cultivation System (EMCS) for the the first run of the Plant Gravity Perception experiment to test the gravity-sensing ability of plants in microgravity.

Effecting aging time of epoxy molding compound to molding process for integrated circuit packaging

NASA Astrophysics Data System (ADS)

Tachapitunsuk, Jirayu; Ugsornrat, Kessararat; Srisuwitthanon, Warayoot; Thonglor, Panakamon

2017-09-01

This research studied about effecting aging time of epoxy molding compound (EMC) that effect to reliability performance of integrated circuit (IC) package in molding process. Molding process is so important of IC packaging process for protecting IC chip (or die) from temperature and humidity environment using encapsulated EMC. For general molding process, EMC are stored in the frozen at 5°C and left at room temperature at 25 °C for aging time on self before molding of die onto lead frame is 24 hours. The aging time effect to reliability performance of IC package due to different temperature and humidity inside the package. In experiment, aging time of EMC were varied from 0 to 24 hours for molding process of SOIC-8L packages. For analysis, these packages were tested by x-ray and scanning acoustic microscope to analyze properties of EMC with an aging time and also analyzed delamination, internal void, and wire sweep inside the packages with different aging time. The results revealed that different aging time of EMC effect to properties and reliability performance of molding process.

Lunar Atmosphere and Dust Environment Explorer Integration and Test

NASA Technical Reports Server (NTRS)

Wright, Michael R.; McCormick, John L.

2010-01-01

The Lunar Atmosphere and Dust Environment Explorer (LADEE) is a NASA collaborative flight project to explore the lunar exosphere. It is being developed through a unique partnership between NASA's Ames Research Center (ARC) and Goddard Space Flight Center (GSFC). Each center brings its own experience and flight systems heritage to the task of integrating and testing the LADEE subsystems, instruments, and spacecraft. As an "in-house" flight project being implemented at low-cost and moderate risk, LADEE relies on single-string subsystems and protoflight hardware to accomplish its mission. Integration and test (l&T) of the LADEE spacecraft with the instruments will be performed at GSFC, and includes assembly, integration, functional testing, and flight qualification and acceptance testing. Due to the nature of the LADEE mission, l&T requirements include strict contamination control measures and instrument calibration procedures. Environmental testing will include electromagnetic compatibility (EMC), vibro-acoustic testing, and thermal-balance/vacuum. Upon successful completion of spacecraft l&T, LADEE will be launched from NASA's Wallops Flight Facility. Launch of the LADEE spacecraft is currently scheduled for December 2012.

Electromagnetic Compatibility (EMC) Requirements for Military and Commercial Equipment

DTIC Science & Technology

2009-09-01

Commercial off-the shelf (COTS) use also provides access to what has become a much larger industrial base. With these goals in mind, the Secretary of...Band (110 – 300 GHz) 10–1 mm Microwave data links, radio astronomy , amateur radio, remote sensing, advanced weapons systems 12 Radiated EMI...to what has become a much larger industrial base. With these goals in mind, the Secretary of Defense issued a directive in June 1994 requiring the

EMC design for actuators in the FAST reflector

NASA Astrophysics Data System (ADS)

Zhang, Hai-Yan; Wu, Ming-Chang; Yue, You-Ling; Gan, Heng-Qian; Hu, Hao; Huang, Shi-Jie

2018-04-01

An active reflector is one of the three main innovations incorporated in the Five-hundred-meter Aperture Spherical radio Telescope (FAST). The deformation of such a huge spherically shaped reflector into different transient parabolic shapes is achieved by using 2225 hydraulic actuators which change the position of the 2225 nodes through the connected down tied cables. For each different tracking process of the telescope, more than 1/3 of these 2225 actuators must be in operation to tune the parabolic aperture accurately and meet the surface error restriction. This means that some of these actuators are inevitably located within the main beam of the receiver, and Electromagnetic Interference (EMI) from the actuators must be mitigated to ensure the scientific output of the telescope. Based on the threshold level of interference detrimental to radio astronomy described in ITU-R Recommendation RA.769 and EMI measurements, the shielding efficiency (SE) requirement for each actuator is set to be 80 dB in the frequency range from 70 MHz to 3 GHz. Therefore, Electromagnetic Compatibility (EMC) was taken into account in the actuator design by measures such as power line filters, optical fibers, shielding enclosures and other structural measures. In 2015, all the actuators had been installed at the FAST site. Till now, no apparent EMI from the actuators has been detected by the receiver, which demonstrates the effectiveness of these EMC measures.

Design Guidelines for Shielding Effectiveness, Current Carrying Capability, and the Enhancement of Conductivity of Composite Materials

NASA Technical Reports Server (NTRS)

Evans, R. W.

1997-01-01

These guidelines address the electrical properties of composite materials which may have an effect on electromagnetic compatibility (EMC). The main topics of the guidelines include the electrical shielding, fault current return, and lightning protection capabilities of graphite reinforced polymers, since they are somewhat conductive but may require enhancement to be adequate for EMC purposes. Shielding effectiveness depends heavily upon the conductivity of the material. Graphite epoxy can provide useful shielding against RF signals, but it is approximately 1,000 times more resistive than good conductive metals. The reduced shielding effectiveness is significant but is still useful in many cases. The primary concern is with gaps and seams in the material just as it is with metal. Current carrying capability of graphite epoxy is adequate for dissipation static charges, but fault currents through graphite epoxy may cause fire at the shorting contact and at joints. The effect of lightning on selected graphite epoxy material and mating surfaces is described, and protection methods are reviewed.

Understanding reverberating chambers as an alternative facility for EMC testing

NASA Astrophysics Data System (ADS)

Ma, M. T.

A relatively new facility called a reverberating chamber designed for EMC testing is described. The purpose is to create a statistically uniform electric field inside a metal enclosure for testing radiated susceptibility or immunity of equipment. Design criteria in terms of the number of cavity modes, mode density, and composite quality factor are presented in details in order to understand the physical insight and to enhance interpretations of measurement results. Recent experimental data are included to illustrate the underlying principle.

FDTD simulation of field performance in reverberation chamber excited by two excitation antennas

NASA Astrophysics Data System (ADS)

Wang, Song; Wu, Zhan-cheng; Cui, Yao-zhong

2013-03-01

The excitation source is one of the critical items that determine the electromagnetic fields in a reverberation chamber (RC). In order to optimize the electromagnetic fields performance, a new method of exciting RC with two antennas is proposed based on theoretical analysis. The full 3D simulation of RC is carried out by the finite difference time domain (FDTD) method on two excitation conditions of one antenna and two antennas. The broadband response of RC is obtained by fast Fourier transformation (FFT) after only one simulation. Numerical data show that the field uniformity in the test space is improved on the condition of two transmitting antennas while the normalized electric fields decreased slightly compared to the one antenna condition. It is straightforward to recognize that two antennas excitation can reduce the demands on power amplifier as the total input power is split among the two antennas, and consequently the cost of electromagnetic compatibility (EMC) test in large-scale RC can be reduced.

Open-field test site

NASA Astrophysics Data System (ADS)

Gyoda, Koichi; Shinozuka, Takashi

1995-06-01

An open-field test site with measurement equipment, a turn table, antenna positioners, and measurement auxiliary equipment was remodelled at the CRL north-site. This paper introduces the configuration, specifications and characteristics of this new open-field test site. Measured 3-m and 10-m site attenuations are in good agreement with theoretical values, and this means that this site is suitable for using 3-m and 10-m method EMI/EMC measurements. The site is expected to be effective for antenna measurement, antenna calibration, and studies on EMI/EMC measurement methods.

Comparison of maternal and fetal complications in elective and emergency cesarean section: a systematic review and meta-analysis.

PubMed

Yang, Xiao-Jing; Sun, Shan-Shan

2017-09-01

Though the same types of complication were found in both elective cesarean section (ElCS) and emergence cesarean section (EmCS), the aim of this study is to compare the rates of maternal and fetal morbidity and mortality between ElCS and EmCS. Full-text articles involved in the maternal and fetal complications and outcomes of ElCS and EmCS were searched in multiple database. Review Manager 5.0 was adopted for meta-analysis, sensitivity analysis, and bias analysis. Funnel plots and Egger's tests were also applied with STATA 10.0 software to assess possible publication bias. Totally nine articles were included in this study. Among these articles, seven, three, and four studies were involved in the maternal complication, fetal complication, and fetal outcomes, respectively. The combined analyses showed that both rates of maternal complication and fetal complication in EmCS were higher than those in ElCS. The rates of infection, fever, UTI (urinary tract infection), wound dehiscence, DIC (disseminated intravascular coagulation), and reoperation of postpartum women with EmCS were much higher than those with ElCS. Larger infant mortality rate of EmCS was also observed. Emergency cesarean sections showed significantly more maternal and fetal complications and mortality than elective cesarean sections in this study. Certain plans should be worked out by obstetric practitioners to avoid the post-operative complications.

Electromagnetic compatibility of implantable neurostimulators to RFID emitters

PubMed Central

2011-01-01

Background The objective of this study is to investigate electromagnetic compatibility (EMC) of implantable neurostimulators with the emissions from radio frequency identification (RFID) emitters. Methods Six active implantable neurostimulators with lead systems were tested for susceptibility to electromagnetic fields generated by 22 RFID emitters. These medical devices have been approved for marketing in the U.S. for a number of intended uses that include: epilepsy, depression, incontinence, Parkinsonian tremor and pain relief. Each RFID emitter had one of the following carrier frequencies: 125 kHz, 134 kHz, 13.56 MHz, 433 MHz, 915 MHz and 2.45 GHz Results The test results showed the output of one of the implantable neurostimulators was inhibited by 134 kHz RFID emitter at separation distances of 10 cm or less. The output of the same implantable neurostimulator was also inhibited by another 134 kHz RFID emitter at separation distances of 10 cm or less and also showed inconsistent pulsing rate at a separation distance of 15 cm. Both effects occurred during and lasted through out the duration of the exposure. Conclusions The clinical significance of the effects was assessed by a clinician at the U.S. Food and Drug Administration. The effects were determined to be clinically significant only if they occurred for extended period of time. There were no observed effects from the other 5 implantable neurostimulators or during exposures from other RFID emitters. PMID:21658266

Electromagnetic compatibility of implantable neurostimulators to RFID emitters.

PubMed

Pantchenko, Oxana S; Seidman, Seth J; Guag, Joshua W; Witters, Donald M; Sponberg, Curt L

2011-06-09

The objective of this study is to investigate electromagnetic compatibility (EMC) of implantable neurostimulators with the emissions from radio frequency identification (RFID) emitters. Six active implantable neurostimulators with lead systems were tested for susceptibility to electromagnetic fields generated by 22 RFID emitters. These medical devices have been approved for marketing in the U.S. for a number of intended uses that include: epilepsy, depression, incontinence, Parkinsonian tremor and pain relief. Each RFID emitter had one of the following carrier frequencies: 125 kHz, 134 kHz, 13.56 MHz, 433 MHz, 915 MHz and 2.45 GHz. The test results showed the output of one of the implantable neurostimulators was inhibited by 134 kHz RFID emitter at separation distances of 10 cm or less. The output of the same implantable neurostimulator was also inhibited by another 134 kHz RFID emitter at separation distances of 10 cm or less and also showed inconsistent pulsing rate at a separation distance of 15 cm. Both effects occurred during and lasted through out the duration of the exposure. The clinical significance of the effects was assessed by a clinician at the U.S. Food and Drug Administration. The effects were determined to be clinically significant only if they occurred for extended period of time. There were no observed effects from the other 5 implantable neurostimulators or during exposures from other RFID emitters.

Basic EMC (Electromagnetic compatibility) technology advancement for C3 (Command, control, and communications) systems. Volume 6

NASA Astrophysics Data System (ADS)

Weiner, D.; Paul, C. R.; Whalen, J.

1985-04-01

This research effort was devoted to eliminating some of the basic technological gaps in the two important areas of: (1) electromagnetic effects (EM) on microelectronic circuits and (2) EM coupling and testing. The results are presented in fourteen reports which have been organized into six volumes. The reports are briefly summarized in this volume. In addition, an experiment is described which was performed to demonstrate the feasibility of applying several of the results to a problem involving electromagnetic interference. Specifically, experimental results are provided for the randomness associated with: (1) crosstalk in cable harnesses and (2) demodulation of amplitude modulated (AM) signals in operational amplifiers. These results are combined to predict candidate probability density functions (pdf's) for the amplitude of an AM interfering signal required to turn on a light emitting diode. The candidate pdf's are shown to be statistically consistent with measured data.

Thermal Expansion Behavior of Hot-Pressed Engineered Matrices

NASA Technical Reports Server (NTRS)

Raj, S. V.

2016-01-01

Advanced engineered matrix composites (EMCs) require that the coefficient of thermal expansion (CTE) of the engineered matrix (EM) matches those of the fiber reinforcements as closely as possible in order to reduce thermal compatibility strains during heating and cooling of the composites. The present paper proposes a general concept for designing suitable matrices for long fiber reinforced composites using a rule of mixtures (ROM) approach to minimize the global differences in the thermal expansion mismatches between the fibers and the engineered matrix. Proof-of-concept studies were conducted to demonstrate the validity of the concept.

Basic EMC (Electromagnetic Compatibility) Technology Advancement for C3 Systems, Macromodeling of Digital Circuits. Volume 2B.

DTIC Science & Technology

1984-04-01

dependent source to multiply a ramp by a unit sinusoid. Using this method, data could be extracted from a single run to show the magnitude of the...IHPUT VOLTAGE SOURCES VAC 1 0 0V VAl 2 0 0V VA2 3 0 0V VA3 4 0 PULSE(OV 3V ONSD 2NSR 2NSF 198NSPW) VB0 5 0 OV VB1 6 0 OV VB2 7 0 CV VB3 8 0 PULSE

Design, development, and clinical evaluation of the electronic mobility cane for vision rehabilitation.

PubMed

Bhatlawande, Shripad; Mahadevappa, Manjunatha; Mukherjee, Jayanta; Biswas, Mukul; Das, Debabrata; Gupta, Somedeb

2014-11-01

This paper proposes a new electronic mobility cane (EMC) for providing obstacle detection and way-finding assistance to the visually impaired people. The main feature of this cane is that it constructs the logical map of the surrounding environment to deduce the priority information. It provides a simplified representation of the surrounding environment without causing any information overload. It conveys this priority information to the subject by using intuitive vibration, audio or voice feedback. The other novel features of the EMC are staircase detection and nonformal distance scaling scheme. It also provides information about the floor status. It consists of a low power embedded system with ultrasonic sensors and safety indicators. The EMC was subjected to series of clinical evaluations in order to verify its design and to assess its ability to assist the subjects in their daily-life mobility. Clinical evaluations were performed with 16 totally blind and four low vision subjects. All subjects walked controlled and the real-world test environments with the EMC and the traditional white cane. The evaluation results and significant scores of subjective measurements have shown the usefulness of the EMC in vision rehabilitation services.

Analysis of Waves in Space Plasma (WISP) near field simulation and experiment

NASA Technical Reports Server (NTRS)

Richie, James E.

1992-01-01

The WISP payload scheduler for a 1995 space transportation system (shuttle flight) will include a large power transmitter on board at a wide range of frequencies. The levels of electromagnetic interference/electromagnetic compatibility (EMI/EMC) must be addressed to insure the safety of the shuttle crew. This report is concerned with the simulation and experimental verification of EMI/EMC for the WISP payload in the shuttle cargo bay. The simulations have been carried out using the method of moments for both thin wires and patches to stimulate closed solids. Data obtained from simulation is compared with experimental results. An investigation of the accuracy of the modeling approach is also included. The report begins with a description of the WISP experiment. A description of the model used to simulate the cargo bay follows. The results of the simulation are compared to experimental data on the input impedance of the WISP antenna with the cargo bay present. A discussion of the methods used to verify the accuracy of the model is shown to illustrate appropriate methods for obtaining this information. Finally, suggestions for future work are provided.

Development of Biocompatibility Procedures for Assessment of Plant Growth in Ground Test Hardware for the EMCS

NASA Technical Reports Server (NTRS)

Bowman, R. N.; Steele, M. K.; Sun, S. (Technical Monitor)

2002-01-01

The European Modular Cultivation System (EMCS) is an European Space Agency-developed facility designed to support plant research in microgravity on the IS NASA is responsible for providing US specific hardware to use within the EMCS. In preparation for flight, research will be developed and tested at Ames Research Center in the EMCS ground test hardware, the Experiment Reference Module (ERM) In order to determine the acceptability of the ERM for such purposes, biocompatibility tests will be performed to determine that the hardware functions as intended and successfully supports the' growth of plants. In this report, we describe the development of procedures and the collection of baseline data against which to compare ERM function, e.g. biocompatibility testing. A simple and robust system was developed to grow whole Arabidopsis thaliana plants within the confined volumes characteristic of spaceflight hardware. Our system for growing plants eliminated the necessity of a water/nutrient delivery system and allowed for quantifiable assessment of individual plants, as well as entire population dynamics. To insure uniform germination, seeds were started in small straw segments and transplanted into modified scintillation vials. Seedlings were selected prior to transplantation to decrease genetic variability. Plants were grown for a total of 24 days in standard laboratory plant growth chambers under controlled conditions. Sequential digital still images were taken on a daily basis. Analysis of these images allowed for the quantification of even minute environmental effect, on growth dynamics whole plants. The data collected provide reliable growth curves against which to compare plants grown in the ERM.

Direct-coupled microcomputer-based building emulator for building energy management and control systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lam, H.N.

1999-07-01

In this paper, the development and implementation of a direct-coupled building emulator for a building energy management and control system (EMCS) is presented. The building emulator consists of a microcomputer and a computer model of an air-conditioning system implemented in a modular dynamic simulation software package for direct-coupling to an EMCS, without using analog-to-digital and digital-to-analog converters. The building emulator can be used to simulate in real time the behavior of the air-conditioning system under a given operating environment and subject to a given usage pattern. Software modules for data communication, graphical display, dynamic data exchange, and synchronization of simulationmore » outputs with real time have been developed to achieve direct digital data transfer between the building emulator and a commercial EMCS. Based on the tests conducted, the validity of the building emulator has been established and the proportional-plus-integral control function of the EMCS assessed.« less

Ground Testing of the EMCS Seed Cassette for Biocompatibility with the Tardigrade, Hypsibius dujardini

NASA Technical Reports Server (NTRS)

Reinsch, Sigrid; Myers, Zachary Alan; DeSimone, Julia Carol; Freeman, John L.; Steele, Marianne K.; Sun, Gwo-Shing; Heathcote, David

2014-01-01

The European Modular Cultivation System, EMCS, was developed by ESA for plant experiments. We performed ground testing to determine whether ARC EMCS seed cassettes could be adapted for use with tardigrades for future spaceflight experiments. Tardigrades (water bears) are small invertebrates that enter the tun state in response to desiccation or other environmental stresses. Tardigrade tuns have suspended metabolism and have been shown to be survive exposure to space vacuum, high pressure, temperature and other stresses. For spaceflight experiments using the EMCS, the organisms ideally must be able to survive desiccation and storage in the cassette at ambient temperature for several weeks prior to the initiation of the experiment by the infusion of water to the cassette during spaceflight. The ability of tardigrades to survive extremes by entering the tun state make them ideal candidates for growth experiments in the EMCS cassettes. The growth substratum in the cassettes is a gridded polyether sulfone (PES) membrane. A blotter beneath the PES membrane contains dried growth medium. The goals of our study were to (1) determine whether tardigrades survive and reproduce on PES membranes, (2) develop a consistent method for dehydration of the tardigrades with high recovery rates upon rehydration, (3) to determine an appropriate food source for the tardigrades that can also be dehydrated/rehydrated and (4) successful mock rehydration experiment in cassettes with appropriate food source. We present results that show successful multigenerational growth of tardigrades on PES membranes with a variety of wet food sources. We have successfully performed a mock rehydration with tardigrades and at least one candidate food, protonema of the moss Polytrichum, that supports multigenerational growth and whose spores germinate quickly enough to match tardigrade feeding patterns post rehydration. Our results indicate that experiments on the ISS using the tardigrade, Hypsibius dujardini and other similar species could successfully be performed in the flight verified hardware of the EMCS seed cassettes.

The Effect of Epoxy Molding Compound Floor Life to Reliability Performance and mold ability for QFN Package

NASA Astrophysics Data System (ADS)

Peanpunga, Udom; Ugsornrat, Kessararat; Thorlor, Panakamol; Sumithpibul, Chalermsak

2017-09-01

This research studied about an epoxy molding compound (EMC) floor life to reliability performance of integrated circuit (IC) package. Molding is the process for protecting the die of IC package form mechanical and chemical reaction from external environment by shaping EMC. From normal manufacturing process, the EMC is stored in the frozen at 5oC and left at around room temperature for aging time or floor life before molding process. The EMC floor life effect to its properties and reliability performance of IC package. Therefore, this work interested in varied the floor life of EMC before molding process to analyze properties of EMC such as spiral flow length, gelation time, and viscosity. In experiment, the floor life of EMC was varied to check the effect of its property to reliability performance. The EMC floor life were varied from 0 hours to 60 hours with a step of 12 hours and observed wire sweep, incomplete EMC, and delamination inside the packages for 3x3, 5x5 and 8x8 mm2 of QFN packages. The evaluation showed about clearly effect of EMC floor life to IC packaging reliability. EMC floor life is not any concern for EMC property, moldabilty, and reliability from 0 hours to 48 hours for molding process of 3x3,5x5 and 8x8 mm2 QFN packaging manufacturing

Multigen-2 Pre-Flight Testing: Science Testing Unit (STU) and Stowage Conditions

NASA Astrophysics Data System (ADS)

Kittang, A.-I.; Kvaloy, B.; Berg, C.; Rakvaag, G.; Iversen, T.-H.

2008-06-01

The Multigen-2 experiment Science Testing Unit (STU) proved to be a useful tool in optimizing experiment environment settings for cultivation of Arabidopsis thaliana (Col-0) in the European Modular Cultivation System (EMCS). By using the EMCS Experiment Reference Model (ERM); light, temperature and air flow regimes for optimal growth could be tested. Healthy seedlings were obtained using the STU#2 and STU#3 in the EMCS ERM. It was concluded that the Experiment Container Development Kit (ECDK) is unsuitable for the Multigen-2 testing due to limitation in the ECDK temperature control. The results from the stowage condition tests showed that the selected growth medium (agar) can be used after 3 months at +4°C. The seeds show a germination rate of ≥80% after sterilisation and stowed for 5 months. The Multigen-2 plant samples will be fixed in RNA later and stored at - 80 °C. Three methods with different RNA isolation kits showed that the Qiagen kit (#74904) gave the highest amount and the best quality of Total RNA from RNA Later and frozen samples. The amount of plant material from one cultivation chamber gives two RNA isolations. Each of the isolations gives Total RNA sufficient for at least two microarray analyses.

1998 Conference on Precision Electromagnetic Measurements Digest. Proceedings.

NASA Astrophysics Data System (ADS)

Nelson, T. L.

The following topics were dealt with: fundamental constants; caesium standards; AC-DC transfer; impedance measurement; length measurement; units; statistics; cryogenic resonators; time transfer; QED; resistance scaling and bridges; mass measurement; atomic fountains and clocks; single electron transport; Newtonian constant of gravitation; stabilised lasers and frequency measurements; cryogenic current comparators; optical frequency standards; high voltage devices and systems; international compatibility; magnetic measurement; precision power measurement; high resolution spectroscopy; DC transport standards; waveform acquisition and analysis; ion trap standards; optical metrology; quantised Hall effect; Josephson array comparisons; signal generation and measurement; Avogadro constant; microwave networks; wideband power standards; antennas, fields and EMC; quantum-based standards.

Hearing aid-compatible mobile handsets, petition of American National Standards Committee C63 (EMC) ANSO ASC C63 (TM). Final rule.

PubMed

2008-05-07

The Federal Communications Commission (Commission) adopts various proposals to amend its hearing aid compatibility policies and requirements pertaining to wireless services, including modifications and other requirements along the framework proposed in a consensus plan (Joint Consensus Plan) developed jointly by industry and representatives for the deaf and hard of hearing community. The Commission anticipates that these rule changes, taken together and largely supported by manufacturers, service providers, and consumers with hearing loss, will meet statutory obligations to ensure reasonable access to telephone service by persons with impaired hearing. These requirements are intended to benefit wireless users in the deaf and hard of hearing community, including the most disadvantaged who are more likely to rely on telecoil-equipped hearing aids, as well as to ensure that these consumers have a variety of handsets available to them, including handsets with innovative features.

IEEE 1988 International Symposium on Electromagnetic Compatibility, Seattle, WA, Aug. 2-4, 1988, Record

NASA Astrophysics Data System (ADS)

Various papers on electromagnetic compatibility are presented. Some of the optics considered include: field-to-wire coupling 1 to 18 GHz, SHF/EHF field-to-wire coupling model, numerical method for the analysis of coupling to thin wire structures, spread-spectrum system with an adaptive array for combating interference, technique to select the optimum modulation indices for suppression of undesired signals for simultaneous range and data operations, development of a MHz RF leak detector technique for aircraft harness surveillance, and performance of standard aperture shielding techniques at microwave frequncies. Also discussed are: spectrum efficiency of spread-spectrum systems, control of power supply ripple produced sidebands in microwave transistor amplifiers, an intership SATCOM versus radar electromagnetic interference prediction model, considerations in the design of a broadband E-field sensing system, unique bonding methods for spacecraft, and review of EMC practice for launch vehicle systems.

The prognostic value of visually assessing enamel microcracks: Do debonding and adhesive removal contribute to their increase?

PubMed

Dumbryte, Irma; Jonavicius, Tomas; Linkeviciene, Laura; Linkevicius, Tomas; Peciuliene, Vytaute; Malinauskas, Mangirdas

2016-05-01

To find a correlation between the severity of enamel microcracks (EMCs) and their increase during debonding and residual adhesive removal (RAR). Following their examination with scanning electron microscopy (SEM), 90 extracted human premolars were divided into three groups of 30: group 1, teeth having pronounced EMCs (visible with the naked eye under normal room illumination); group 2, teeth showing weak EMCs (not apparent under normal room illumination but visible by SEM); and group 3, a control group. EMCs have been classified into weak and pronounced, based on their visibility. Metal brackets (MB) and ceramic brackets (CB), 15 of each type, were bonded to all the teeth from groups 1 and 2. Debonding was performed with pliers, followed by RAR. The location, length, and width of the longest EMCs were measured using SEM before and after debonding. The mean overall width (Woverall) was higher for pronounced EMCs before and after debonding CB (P < .05), and after the removal of MB. Pronounced EMCs showed greater length values using both types of brackets. After debonding, the increase in Woverall of pronounced EMCs was 0.57 µm with MB (P < .05) and 0.30 µm with CB; for weak EMCs, - 0.32 µm with MB and 0.30 µm with CB. Although the teeth having pronounced EMCs showed higher width and length values, this did not predispose to greater EMCs increase after debonding MB and CB followed by RAR.

Basic EMC (Electromagnetic compatibility) technology advancement for C3 systems. Volume 4D: Modeling crosstalk in balanced twisted pairs

NASA Astrophysics Data System (ADS)

Koopman, D. A.; Paul, C. R.

1984-08-01

Electrical devices (computers, radar systems, communication radios, etc.) are interconnected by wires on most present systems. Electromagnetic fields produced by the excitation of these wires will cause unintentional coupling of signals onto nearby wires. This undesired electromagnetic coupling is termed crosstalk. It is important to be able to determine whether these crosstalk signals will cause the devices at the ends of the wires to malfunction. Wires are often grouped together in cable bundles or harnesses. The close proximity of wires in these bundles enhances the possibility that the crosstalk levels will be sufficiently large to cause malfunctions. The ability to predict crosstalk levels and the means to control crosstalk when it causes a problem are important to optimum system design. It interference of this type is allowed to surface during final system tests, a costly and time consuming retrofit of the wiring or the addition of filters and other interference control measures may be required.

Electromagnetic code for naval applications

NASA Astrophysics Data System (ADS)

Crescimbeni, F.; Bessi, F.; Chiti, S.

1988-12-01

The use of an increasing number of electronic apparatus became vital to meet the high performance required for military Navy applications. Thus the number of antennas to be mounted on shipboard greatly increased. As a consequence of the high antenna density, of the complexity of the shipboard environment and of the powers used for communication and radar systems, the EMC (Electro-Magnetic Compatibility) problem is playing a leading role in the design of the topside of a ship. The Italian Navy has acquired a numerical code for the antenna siting and design. This code, together with experimental data measured at the Italian Navy test range facility, allows for the evaluation of optimal sitings for antenna systems on shipboard, and the prediction of their performances in the actual environment. The structure of this code, named Programma Elettromagnetico per Applicazioni Navali, (Electromagnetic Code for Naval Applications) is discussed, together with its capabilities and applications. Also the results obtained in some examples are presented and compared with the measurements.

Efficient replication of the novel human betacoronavirus EMC on primary human epithelium highlights its zoonotic potential.

PubMed

Kindler, Eveline; Jónsdóttir, Hulda R; Muth, Doreen; Hamming, Ole J; Hartmann, Rune; Rodriguez, Regulo; Geffers, Robert; Fouchier, Ron A M; Drosten, Christian; Müller, Marcel A; Dijkman, Ronald; Thiel, Volker

2013-02-19

The recent emergence of a novel human coronavirus (HCoV-EMC) in the Middle East raised considerable concerns, as it is associated with severe acute pneumonia, renal failure, and fatal outcome and thus resembles the clinical presentation of severe acute respiratory syndrome (SARS) observed in 2002 and 2003. Like SARS-CoV, HCoV-EMC is of zoonotic origin and closely related to bat coronaviruses. The human airway epithelium (HAE) represents the entry point and primary target tissue for respiratory viruses and is highly relevant for assessing the zoonotic potential of emerging respiratory viruses, such as HCoV-EMC. Here, we show that pseudostratified HAE cultures derived from different donors are highly permissive to HCoV-EMC infection, and by using reverse transcription (RT)-PCR and RNAseq data, we experimentally determined the identity of seven HCoV-EMC subgenomic mRNAs. Although the HAE cells were readily responsive to type I and type III interferon (IFN), we observed neither a pronounced inflammatory cytokine nor any detectable IFN responses following HCoV-EMC, SARS-CoV, or HCoV-229E infection, suggesting that innate immune evasion mechanisms and putative IFN antagonists of HCoV-EMC are operational in the new host. Importantly, however, we demonstrate that both type I and type III IFN can efficiently reduce HCoV-EMC replication in HAE cultures, providing a possible treatment option in cases of suspected HCoV-EMC infection. IMPORTANCE A novel human coronavirus, HCoV-EMC, has recently been described to be associated with severe respiratory tract infection and fatalities, similar to severe acute respiratory syndrome (SARS) observed during the 2002-2003 epidemic. Closely related coronaviruses replicate in bats, suggesting that, like SARS-CoV, HCoV-EMC is of zoonotic origin. Since the animal reservoir and circumstances of zoonotic transmission are yet elusive, it is critically important to assess potential species barriers of HCoV-EMC infection. An important first barrier against invading respiratory pathogens is the epithelium, representing the entry point and primary target tissue of respiratory viruses. We show that human bronchial epithelia are highly susceptible to HCoV-EMC infection. Furthermore, HCoV-EMC, like other coronaviruses, evades innate immune recognition, reflected by the lack of interferon and minimal inflammatory cytokine expression following infection. Importantly, type I and type III interferon treatment can efficiently reduce HCoV-EMC replication in the human airway epithelium, providing a possible avenue for treatment of emerging virus infections.

Expression of hypoxia-inducible 2 (HIG2) protein in uterine cancer.

PubMed

Nishimura, S; Tsuda, H; Nomura, H; Kataoka, F; Chiyoda, T; Tanaka, H; Tanaka, K; Susumu, N; Aoki, D

2011-01-01

For both cervical cancer (UCC) and endometrial cancer (EMC) there are no effective prognostic markers. In this study, we evaluated HIG2 protein expression in 332 uterine cancers (186 UCCs and 146 EMCs) and examined the relationship between HIG2 protein expression and clinical factors, including prognosis. Totally, HIG2 expression was detected in 58% of UCC and 66% of EMC. However, there was no significant relationship between HIG2 expression and age, clinical stage and histology in either UCC or EMC. In addition, HIG2 protein expression was not related to prognosis of UCC or EMC. The positivity rate of HIG2 protein was 56% and 61% in early-stage UCC and EMC, respectively and 67% in non-squamous cell carcinoma of UCC. The positivity rate of HIG2 protein was high even in early-stage UCC and EMC

Explanatory model of emotional-cognitive variables in school mathematics performance: a longitudinal study in primary school.

PubMed

Cerda, Gamal; Pérez, Carlos; Navarro, José I; Aguilar, Manuel; Casas, José A; Aragón, Estíbaliz

2015-01-01

This study tested a structural model of cognitive-emotional explanatory variables to explain performance in mathematics. The predictor variables assessed were related to students' level of development of early mathematical competencies (EMCs), specifically, relational and numerical competencies, predisposition toward mathematics, and the level of logical intelligence in a population of primary school Chilean students (n = 634). This longitudinal study also included the academic performance of the students during a period of 4 years as a variable. The sampled students were initially assessed by means of an Early Numeracy Test, and, subsequently, they were administered a Likert-type scale to measure their predisposition toward mathematics (EPMAT) and a basic test of logical intelligence. The results of these tests were used to analyse the interaction of all the aforementioned variables by means of a structural equations model. This combined interaction model was able to predict 64.3% of the variability of observed performance. Preschool students' performance in EMCs was a strong predictor for achievement in mathematics for students between 8 and 11 years of age. Therefore, this paper highlights the importance of EMCs and the modulating role of predisposition toward mathematics. Also, this paper discusses the educational role of these findings, as well as possible ways to improve negative predispositions toward mathematical tasks in the school domain.

EMC Recent Additions

EPA Pesticide Factsheets

This page has information about recent changes to promulgated and proposed test methods, perfomance specifications, and quality assurance procedures. It also includes updates and changes to all other approved and proposed test methods.

Epithelial-myoepithelial carcinoma with myoepithelial anaplasia: report of a case with cytologic findings of a rare variant.

PubMed

Suzuki, Takashi; Murata, Shin-ichi; Yamaguchi, Hiroshi; Shimizu, Yoshihiko; Shimizu, Michio

2010-01-01

Epithelial-myoepithelial carcinoma (EMC) is usually a low grade malignancy with rare mortality. Rare aggressive variants of EMC, dedifferentiated EMC and EMC with myoepithelial anaplasia have been reported. An 81-year-old man presented with EMC of the parotid gland showing the classical type at the time of initial presentation and a high grade type with myoepithelial anaplasia at recurrence after 10 years. We compared the histologic and cytologic findings of the initial and recurrent tumors. Aspiration cytology of the initial tumor was typical of classical EMC, represented by a biphasic pattern composed of sheetlike and tubular clusters. In contrast, cytologic specimens of the recurrent tumor, which had a focally biphasic pattern similar to that of the initial tumor, also had many isolated or discohesive piled-up clusters of spindle and polygonal cells with nuclear atypia. The cytologic findings of the recurrent tumor were consistent with a rare variant of EMC with myoepithelial anaplasia. To the best of our knowledge, this is the first report of the cytologic finding of an EMC with myoepithelial anaplasia.

Elastic memory composites (EMC) for deployable industrial and commercial applications

NASA Astrophysics Data System (ADS)

Arzberger, Steven C.; Tupper, Michael L.; Lake, Mark S.; Barrett, Rory; Mallick, Kaushik; Hazelton, Craig; Francis, William; Keller, Phillip N.; Campbell, Douglas; Feucht, Sara; Codell, Dana; Wintergerst, Joe; Adams, Larry; Mallioux, Joe; Denis, Rob; White, Karen; Long, Mark; Munshi, Naseem A.; Gall, Ken

2005-05-01

The use of smart materials and multifunctional components has the potential to provide enhanced performance, improved economics, and reduced safety concerns for applications ranging from outer space to subterranean. Elastic Memory Composite (EMC) materials, based on shape memory polymers and used to produce multifunctional components and structures, are being developed and qualified for commercial use as deployable components and structures. EMC materials are similar to traditional fiber-reinforced composites except for the use of a thermoset shape memory resin that enables much higher packaging strains than traditional composites without damage to the fibers or the resin. This unique capability is being exploited in the development of very efficient EMC structural components for deployable spacecraft systems as well as capability enhancing components for use in other industries. The present paper is intended primarily to describe the transition of EMC materials as smart structure technologies into viable industrial and commercial products. Specifically, the paper discusses: 1) TEMBO EMC materials for deployable space/aerospace systems, 2) TEMBO EMC resins for terrestrial applications, 3) future generation EMC materials.

Efficient Replication of the Novel Human Betacoronavirus EMC on Primary Human Epithelium Highlights Its Zoonotic Potential

PubMed Central

Kindler, Eveline; Jónsdóttir, Hulda R.; Muth, Doreen; Hamming, Ole J.; Hartmann, Rune; Rodriguez, Regulo; Geffers, Robert; Fouchier, Ron A. M.; Drosten, Christian; Müller, Marcel A.; Dijkman, Ronald; Thiel, Volker

2013-01-01

ABSTRACT The recent emergence of a novel human coronavirus (HCoV-EMC) in the Middle East raised considerable concerns, as it is associated with severe acute pneumonia, renal failure, and fatal outcome and thus resembles the clinical presentation of severe acute respiratory syndrome (SARS) observed in 2002 and 2003. Like SARS-CoV, HCoV-EMC is of zoonotic origin and closely related to bat coronaviruses. The human airway epithelium (HAE) represents the entry point and primary target tissue for respiratory viruses and is highly relevant for assessing the zoonotic potential of emerging respiratory viruses, such as HCoV-EMC. Here, we show that pseudostratified HAE cultures derived from different donors are highly permissive to HCoV-EMC infection, and by using reverse transcription (RT)-PCR and RNAseq data, we experimentally determined the identity of seven HCoV-EMC subgenomic mRNAs. Although the HAE cells were readily responsive to type I and type III interferon (IFN), we observed neither a pronounced inflammatory cytokine nor any detectable IFN responses following HCoV-EMC, SARS-CoV, or HCoV-229E infection, suggesting that innate immune evasion mechanisms and putative IFN antagonists of HCoV-EMC are operational in the new host. Importantly, however, we demonstrate that both type I and type III IFN can efficiently reduce HCoV-EMC replication in HAE cultures, providing a possible treatment option in cases of suspected HCoV-EMC infection. PMID:23422412

Error mapping controller: a closed loop neuroprosthesis controlled by artificial neural networks.

PubMed

Pedrocchi, Alessandra; Ferrante, Simona; De Momi, Elena; Ferrigno, Giancarlo

2006-10-09

The design of an optimal neuroprostheses controller and its clinical use presents several challenges. First, the physiological system is characterized by highly inter-subjects varying properties and also by non stationary behaviour with time, due to conditioning level and fatigue. Secondly, the easiness to use in routine clinical practice requires experienced operators. Therefore, feedback controllers, avoiding long setting procedures, are required. The error mapping controller (EMC) here proposed uses artificial neural networks (ANNs) both for the design of an inverse model and of a feedback controller. A neuromuscular model is used to validate the performance of the controllers in simulations. The EMC performance is compared to a Proportional Integral Derivative (PID) included in an anti wind-up scheme (called PIDAW) and to a controller with an ANN as inverse model and a PID in the feedback loop (NEUROPID). In addition tests on the EMC robustness in response to variations of the Plant parameters and to mechanical disturbances are carried out. The EMC shows improvements with respect to the other controllers in tracking accuracy, capability to prolong exercise managing fatigue, robustness to parameter variations and resistance to mechanical disturbances. Different from the other controllers, the EMC is capable of balancing between tracking accuracy and mapping of fatigue during the exercise. In this way, it avoids overstressing muscles and allows a considerable prolongation of the movement. The collection of the training sets does not require any particular experimental setting and can be introduced in routine clinical practice.

Error mapping controller: a closed loop neuroprosthesis controlled by artificial neural networks

PubMed Central

Pedrocchi, Alessandra; Ferrante, Simona; De Momi, Elena; Ferrigno, Giancarlo

2006-01-01

Background The design of an optimal neuroprostheses controller and its clinical use presents several challenges. First, the physiological system is characterized by highly inter-subjects varying properties and also by non stationary behaviour with time, due to conditioning level and fatigue. Secondly, the easiness to use in routine clinical practice requires experienced operators. Therefore, feedback controllers, avoiding long setting procedures, are required. Methods The error mapping controller (EMC) here proposed uses artificial neural networks (ANNs) both for the design of an inverse model and of a feedback controller. A neuromuscular model is used to validate the performance of the controllers in simulations. The EMC performance is compared to a Proportional Integral Derivative (PID) included in an anti wind-up scheme (called PIDAW) and to a controller with an ANN as inverse model and a PID in the feedback loop (NEUROPID). In addition tests on the EMC robustness in response to variations of the Plant parameters and to mechanical disturbances are carried out. Results The EMC shows improvements with respect to the other controllers in tracking accuracy, capability to prolong exercise managing fatigue, robustness to parameter variations and resistance to mechanical disturbances. Conclusion Different from the other controllers, the EMC is capable of balancing between tracking accuracy and mapping of fatigue during the exercise. In this way, it avoids overstressing muscles and allows a considerable prolongation of the movement. The collection of the training sets does not require any particular experimental setting and can be introduced in routine clinical practice. PMID:17029636

Spacecraft-level verification of the Van Allen Probes' RF communication system

NASA Astrophysics Data System (ADS)

Crowne, M. J.; Srinivasan, D.; Royster, D.; Weaver, G.; Matlin, D.; Mosavi, N.

This paper presents the verification process, lessons learned, and selected test results of the radio frequency (RF) communication system of the Van Allen Probes, formerly known as the Radiation Belt Storm Probes (RBSP). The Van Allen Probes mission is investigating the doughnut-shaped regions of space known as the Van Allen radiation belts where the Sun interacts with charged particles trapped in Earth's magnetic field. Understanding this dynamic area that surrounds our planet is important to improving our ability to design spacecraft and missions for reliability and astronaut safety. The Van Allen Probes mission features two nearly identical spacecraft designed, built, and operated by the Johns Hopkins University Applied Physics Laboratory (JHU/APL) for the National Aeronautics and Space Administration (NASA). The RF communication system features the JHU/APL Frontier Radio. The Frontier Radio is a software-defined radio (SDR) designed for spaceborne communications, navigation, radio science, and sensor applications. This mission marks the first spaceflight usage of the Frontier Radio. RF ground support equipment (RF GSE) was developed using a ground station receiver similar to what will be used in flight and whose capabilities provided clarity into RF system performance that was previously not obtained until compatibility testing with the ground segments. The Van Allen Probes underwent EMC, acoustic, vibration, and thermal vacuum testing at the environmental test facilities at APL. During this time the RF communication system was rigorously tested to ensure optimal performance, including system-level testing down to threshold power levels. Compatibility tests were performed with the JHU/APL Satellite Communication Facility (SCF), the Universal Space Network (USN), and the Tracking and Data Relay Satellite System (TDRSS). Successful completion of this program as described in this paper validated the design of the system and demonstrated that it will be able to me- t all of the Van Allen Probes's communications requirements with its intended ground segments.

Numerical analysis of electromagnetic cascades in emulsion chambers

NASA Technical Reports Server (NTRS)

Plyasheshnikov, A. V.; Vorobyev, K. V.

1985-01-01

A new calculational scheme of the Monte Carlo method assigned for the investigation of the development of high and extremely high energy electromagnetic cascades (EMC) in the matter was elaborated. The scheme was applied to the analysis of angular and radial distributions of EMC electrons in the atmosphere. By means of this scheme the EMC development in dense medium is investigated and some preliminary data are presented on the behavior of EMC in emulsion chambers. The results of more detailed theoretical analysis of the EMC development in emulsion chambers are discussed.

Effects of long-term estrogen replacement therapy on bone turnover in periarticular tibial osteophytes in surgically postmenopausal cynomolgus monkeys

PubMed Central

Olson, Erik J.; Lindgren, Bruce R.; Carlson, Cathy S.

2008-01-01

The aims of the present study were to assess the effects of long-term estrogen replacement therapy (ERT) on size and indices of bone turnover in periarticular osteophytes in ovariectomized cynomolgus monkeys and to compare dynamic indices of bone turnover in osteophyte bone with those of subchondral bone (SCB) and epiphyseal/metaphyseal cancellous (EMC) bone. One hundred sixty-five adult female cynomolgus macaques were bilaterally ovariectomized and randomly divided into three age- and weight-matched treatment groups for a 36-month treatment period. Group 1 (OVX control) received no treatment, Group 2 (SPE) received soy phytoestrogens, and Group 3 (ERT) received conjugated equine estrogens in the diet; all monkeys were labeled with calcein before necropsy. A midcoronal, plastic-embedded section of the right proximal tibia from 20 randomly selected animals per treatment group was examined histologically. Forty-nine of the sections (OVX control, n=16; SPE, n=16; ERT, n=17) contained lateral abaxial osteophytes, and static and dynamic histomorphometry measurements were taken from osteophyte bone, SCB from the lateral tibial plateau, and EMC bone. Data were analyzed using the ANOVA and Kruskal-Wallis test, correlation and regression methods, and the Friedman and Wilcoxon signed rank test. There was no significant effect of long-term ERT on osteophyte area or on any static or dynamic histomorphometry parameters. The bone volume, trabecular number, and trabecular thickness in osteophyte bone were considerably higher than in EMC bone; whereas, trabecular separation was considerably lower in osteophyte bone. In all three treatment groups, BS/BV was significantly lower in osteophyte bone vs. EMC bone and significantly higher in osteophyte bone vs. lateral SCB. We conclude that osteophyte area and static and dynamic histomorphometry parameters within periarticular tibial osteophytes in ovariectomized cynomolgus monkeys are not significantly influenced by long-term ERT, but that site differences in static and dynamic bone histomorphometry parameters exist, particularly between EMC and osteophyte bone. PMID:18291743

Effects of long-term estrogen replacement therapy on bone turnover in periarticular tibial osteophytes in surgically postmenopausal cynomolgus monkeys.

PubMed

Olson, Erik J; Lindgren, Bruce R; Carlson, Cathy S

2008-05-01

The aims of the present study were to assess the effects of long-term estrogen replacement therapy (ERT) on size and indices of bone turnover in periarticular osteophytes in ovariectomized cynomolgus monkeys and to compare dynamic indices of bone turnover in osteophyte bone with those of subchondral bone (SCB) and epiphyseal/metaphyseal cancellous (EMC) bone. One hundred sixty-five adult female cynomolgus macaques were bilaterally ovariectomized and randomly divided into three age- and weight-matched treatment groups for a 36-month treatment period. Group 1 (OVX control) received no treatment, Group 2 (SPE) received soy phytoestrogens, and Group 3 (ERT) received conjugated equine estrogens in the diet; all monkeys were labeled with calcein before necropsy. A midcoronal, plastic-embedded section of the right proximal tibia from 20 randomly selected animals per treatment group was examined histologically. Forty-nine of the sections (OVX control, n=16; SPE, n=16; ERT, n=17) contained lateral abaxial osteophytes, and static and dynamic histomorphometry measurements were taken from osteophyte bone, SCB from the lateral tibial plateau, and EMC bone. Data were analyzed using the ANOVA and Kruskal-Wallis test, correlation and regression methods, and the Friedman and Wilcoxon signed rank test. There was no significant effect of long-term ERT on osteophyte area or on any static or dynamic histomorphometry parameters. The bone volume, trabecular number, and trabecular thickness in osteophyte bone were considerably higher than in EMC bone; whereas, trabecular separation was considerably lower in osteophyte bone. In all three treatment groups, BS/BV was significantly lower in osteophyte bone vs. EMC bone and significantly higher in osteophyte bone vs. lateral SCB. We conclude that osteophyte area and static and dynamic histomorphometry parameters within periarticular tibial osteophytes in ovariectomized cynomolgus monkeys are not significantly influenced by long-term ERT, but that site differences in static and dynamic bone histomorphometry parameters exist, particularly between EMC and osteophyte bone.

Moisture content of wood for interior use...Douglas-fir and robusta eucalyptus samples studied

Treesearch

R. Sidney Boone

1967-01-01

Panels of Douglas-fir and robusta eucalyptus blocks showed little seasonal variation in Equilibrium Moisture Content (EMC) of wood at 19 indoor locations on Oahu, Hawaii. Differences in EMC between locations were more variable. Minimum EMC at nonair-conditioned locations was 10 percent;at air-conditioned locations. 8 percent. Maximum EMC at nonairconditioned locations...

EMC Test Report: StangSat - CubeSat Program

NASA Technical Reports Server (NTRS)

Carmody, Lynne M.; Aragona, Peter S.

2013-01-01

This report documents the Electromagnetic Interference E M I testing performed on the StangSat; the unit under test (UUT). Testing was per the requirements of MIL STD-461F. The UUT was characterized and passed the radiated emissions (RE102 limit for Spacecraft) testing.

Development of a cognitive function test using virtual reality technology: examination in healthy participants.

PubMed

Sakai, Hiromi; Nagano, Akinori; Seki, Keiko; Okahashi, Sayaka; Kojima, Maki; Luo, Zhiwei

2018-07-01

We developed a virtual reality test to assess the cognitive function of Japanese people in near-daily-life environment, namely, a virtual shopping test (VST). In this test, participants were asked to execute shopping tasks using touch panel operations in a "virtual shopping mall." We examined differences in VST performances among healthy participants of different ages and correlations between VST and screening tests, such as the Mini-Mental State Examination (MMSE) and Everyday Memory Checklist (EMC). We included 285 healthy participants between 20 and 86 years of age in seven age groups. Therefore, each VST index tended to decrease with advancing age; differences among age groups were significant. Most VST indices had a significantly negative correlation with MMSE and significantly positive correlation with EMC. VST may be useful for assessing general cognitive decline; effects of age must be considered for proper interpretation of the VST scores.

Explanatory model of emotional-cognitive variables in school mathematics performance: a longitudinal study in primary school

PubMed Central

Cerda, Gamal; Pérez, Carlos; Navarro, José I.; Aguilar, Manuel; Casas, José A.; Aragón, Estíbaliz

2015-01-01

This study tested a structural model of cognitive-emotional explanatory variables to explain performance in mathematics. The predictor variables assessed were related to students’ level of development of early mathematical competencies (EMCs), specifically, relational and numerical competencies, predisposition toward mathematics, and the level of logical intelligence in a population of primary school Chilean students (n = 634). This longitudinal study also included the academic performance of the students during a period of 4 years as a variable. The sampled students were initially assessed by means of an Early Numeracy Test, and, subsequently, they were administered a Likert-type scale to measure their predisposition toward mathematics (EPMAT) and a basic test of logical intelligence. The results of these tests were used to analyse the interaction of all the aforementioned variables by means of a structural equations model. This combined interaction model was able to predict 64.3% of the variability of observed performance. Preschool students’ performance in EMCs was a strong predictor for achievement in mathematics for students between 8 and 11 years of age. Therefore, this paper highlights the importance of EMCs and the modulating role of predisposition toward mathematics. Also, this paper discusses the educational role of these findings, as well as possible ways to improve negative predispositions toward mathematical tasks in the school domain. PMID:26441739

EMC Aspects of Turbulence Heating ObserveR (THOR) Spacecraft

NASA Astrophysics Data System (ADS)

Soucek, J.; Ahlen, L.; Bale, S.; Bonnell, J.; Boudin, N.; Brienza, D.; Carr, C.; Cipriani, F.; Escoubet, C. P.; Fazakerley, A.; Gehler, M.; Genot, V.; Hilgers, A.; Hanock, B.; Jannet, G.; Junge, A.; Khotyaintsev, Y.; De Keyser, J.; Kucharek, H.; Lan, R.; Lavraud, B.; Leblanc, F.; Magnes, W.; Mansour, M.; Marcucci, M. F.; Nakamura, R.; Nemecek, Z.; Owen, C.; Phal, Y.; Retino, A.; Rodgers, D.; Safrankova, J.; Sahraoui, F.; Vainio, R.; Wimmer-Schweingruber, R.; Steinhagen, J.; Vaivads, A.; Wielders, A.; Zaslavsky, A.

2016-05-01

Turbulence Heating ObserveR (THOR) is a spacecraft mission dedicated to the study of plasma turbulence in near-Earth space. The mission is currently under study for implementation as a part of ESA Cosmic Vision program. THOR will involve a single spinning spacecraft equipped with state of the art instruments capable of sensitive measurements of electromagnetic fields and plasma particles. The sensitive electric and magnetic field measurements require that the spacecraft- generated emissions are restricted and strictly controlled; therefore a comprehensive EMC program has been put in place already during the study phase. The THOR study team and a dedicated EMC working group are formulating the mission EMC requirements already in the earliest phase of the project to avoid later delays and cost increases related to EMC. This article introduces the THOR mission and reviews the current state of its EMC requirements.

Next generation sequencing of extraskeletal myxoid chondrosarcoma.

PubMed

Davis, Elizabeth J; Wu, Yi-Mi; Robinson, Dan; Schuetze, Scott M; Baker, Laurence H; Athanikar, Jyoti; Cao, Xuhong; Kunju, Lakshmi P; Chinnaiyan, Arul M; Chugh, Rashmi

2017-03-28

Extraskeletal myxoid chondrosarcoma (EMC) is an indolent translocation-associated soft tissue sarcoma with a high propensity for metastases. Using a clinical sequencing approach, we genomically profiled patients with metastatic EMC to elucidate the molecular biology and identify potentially actionable mutations. We also evaluated potential predictive factors of benefit to sunitinib, a multi-targeted tyrosine kinase inhibitor with reported activity in a subset of EMC patients. Between January 31, 2012 and April 15, 2016, six patients with EMC participated in the clinical sequencing research study. High quality DNA and RNA was isolated and matched normal samples underwent comprehensive next generation sequencing (whole or OncoSeq capture exome of tumor and normal, tumor PolyA+ and capture transcriptome). The expression levels of sunitinib targeted-kinases were measured by transcriptome sequencing for KDR, PDGFRA/B, KIT, RET, FLT1, and FLT4. The previously reported EWSR1-NR4A3 translocation was identified in all patient tumors; however, other recurring genomic abnormalities were not detected. RET expression was significantly greater in patients with EMC relative to other types of sarcomas except for liposarcoma (p<0.0002). The folate receptor was overexpressed in two patients. Our study demonstrated that similar to other translocation-associated sarcomas, the mutational profile of metastatic EMC is limited beyond the pathognomonic translocation. The clinical significance of RET expression in EMC should be explored. Additional pre-clinical investigations of EMC may help elucidate molecular mechanisms contributing to EMC tumorigenesis that could be translated to the clinical setting.

[Stimulation of mouse encephalomyocarditis virus reproduction by non-multiplying poliomyelitis virus in several transplantable tissue culture lines].

PubMed

Maslova, S V; Shirman, G A; Gavrilovskaia, I N

1977-01-01

Reproduction of mouse encephalomyocarditis virus (EMC) was studied in 5 continuous primate cell lines: HeLa, Fl, Detroit-6, P/7, and MIO inoculated with guanidine-dependent variant of poliomyelitis virus in the absence of guanidine. Poliomyelitis virus stimulated EMC virus reproduction in all cell lines under study. This stimulation effect was studied at length in HeLa and MIO cells. In HeLa cells, stimulation was observed at a low and moderate multiplicity of infection of EMC virus but not at a high (100 PEU/cell) multiplicity. Also, when EMC virus reproduction was stimulated, a shortening of the latent period of its multiplication cycle, an increase in the number of antigen-containing cells and the number of infectious centers were observed. In MIO cells, stimulation was found to occur both with low and high doses of EMC virus but not to be accompanied by a shortening in the latent period of EMC reproduction cycle, or any increase in the antigen-containing cells or number of infectious centers. In both cell types upon mixed infection the synthesis of virus-specific RNA's of EMC virus was enhanced. It is suggested that the stimulating effect of poliomyelitis virus is realized in HeLa and MIO cells at different stages of EMC virus reproduction.

Warpage of QFN Package in Post Mold Cure Process of integrated circuit packaging

NASA Astrophysics Data System (ADS)

Sriwithoon, Nattha; Ugsornrat, Kessararat; Srisuwitthanon, Warayoot; Thonglor, Panakamon

2017-09-01

This research studied about warpage of QFN package in post mold cure process of integrated circuit (IC) packages using pre-plated (PPF) leadframe. For IC package, epoxy molding compound (EMC) are molded by cross linking of compound stiffness but incomplete crosslinked network and leading the fully cured thermoset by post mold cure (PMC) process. The cure temperature of PMC can change microstructure of EMC in term of stress inside the package and effect to warpage of the package due to coefficient of thermal expansion (CTE) between EMC and leadframe. In experiment, cure temperatures were varied to check the effect of internal stress due to different cure temperature after completed post mold cure for TDFN 2×3 8L. The cure temperature were varied with 180 °C, 170 °C, 160 °C, and 150°C with cure time 4 and 6 hours, respectively. For analysis, the TDFN 2×3 8L packages were analyzed the warpage by thickness gauge and scanning acoustic microscope (SAM) after take the test samples out from the oven cure. The results confirmed that effect of different CTE between EMC and leadframe due to different cure temperature resulting to warpage of the TDFN 2×3 8L packages.

Seasonal variation of fecal indicator bacteria in storm events within the US stormwater database.

PubMed

Pan, Xubin; Jones, Kim D

2012-01-01

Bacteria are one of the major causes of surface water impairments in the USA. Over the past several years, best management practices, including detention basins, manufactured devices, grass swales, filters and bioretention cells have been used to remove bacteria and other pollutants from stormwater runoff. However, there are data gaps in the comprehensive studies of bacteria concentrations in stormwater runoff. In this paper, the event mean concentration (EMC) of fecal indicator bacteria (Enterococcus, Escherichia coli, fecal Streptococcus group bacteria, and fecal coliform) across the USA was retrieved from the international stormwater best management practices database to analyze the seasonal variations of inflow and outflow event mean concentrations and removal efficiencies. The Kruskal-Wallis test was employed to determine the seasonal variations of bacteria indicator concentrations and removals, and the two-sample Kolmogorov-Smirnov test was used for comparing different seasonal outcomes. The results indicate that all the inflow EMC of FIB in stormwater runoff is above the water quality criteria. The seasonal differences of fecal Streptococcus group bacteria and fecal coliform are significant. Summer has the potential to increase the bacteria EMC and illustrate the seasonal differences.

Missile telemetry systems for flight tests and EMC tests on EED's

NASA Astrophysics Data System (ADS)

Freymann, D.

1985-06-01

This paper describes telemetry systems developed for use in the 'Roland', 'MLRS AT2' and 'Kormoran' missiles. The main design effort required to obtain a high performance of telemetry data acquisition and transmission under extreme environmental conditions are discussed, along with test results. Considered are different types of PCM telemetry systems where the data is either transmitted directly to the ground via an RF or fiber optic link or stored in an onboard solid-state memory. The safety of EEDs in the presence of unwanted electromagnetic fields or currents is very important in weapon-systems. Therefore another type of telemetry system is reported here allowing the measurement of extremely small DC- and RF-currents induced on EEDs during EMC ground-tests. These telemetry signals are transmitted via fiber optics, to avoid additional coupling. Finally, there is a brief commentary on the future design philosophy of missile telemetry systems.

Evaluation of a Commercially Available Single Building EMCS (Energy Monitoring Control System).

DTIC Science & Technology

1985-02-01

Available Single Building EMCS K i,,n vir Sanchey. John Franchi and Karlin Canfield S -,or isored by Naval Material Cor it iand February. 1985 LU...BUILDING EMCS (SBEMCS), (Final) by Ivan Sanchez and John Franchi TR-914 29 pp illus February 1985 Unclassified 1. EMCS 2. Energy conservation I. Z0371-O1...Ivan Sanchez, John Franchi and Karlin Canfield 9 PERFORMING ORGANIZAT.ON NAME AND ADDRESS 𔃺 PROGRAM ELEMENT PROJECT, TASKAREA & WORK UNIIT NUMBERS

EMC effect in the Drell-Yan process at COMPASS

NASA Astrophysics Data System (ADS)

Mitrofanov, Evgenii

2018-04-01

The EMC effect or a modification of parton distributions in bound nucleons as compared to free ones, has been extensively studied during the last 30 years but its full understanding is still lacking. The COMPASS experiment at CERN will provide new results on the EMC effect, originating from the Drell-Yan process and studied in the 190 GeV=c π- beam scattering on the ammonia and tungsten targets. The present understanding of the EMC effect and experimental possibilities of COMPASS in this context are discussed.

Management of the JWST MIRI pFM environmental and performance verification test campaign

NASA Astrophysics Data System (ADS)

Eccleston, Paul; Glasse, Alistair; Grundy, Timothy; Detre, Örs Hunor; O'Sullivan, Brian; Shaughnessy, Bryan; Sykes, Jon; Thatcher, John; Walker, Helen; Wells, Martyn; Wright, Gillian; Wright, David

2012-09-01

The Mid-Infrared Instrument (MIRI) is one of four scientific instruments on the James Webb Space Telescope (JWST) observatory, scheduled for launch in 2018. It will provide unique capabilities to probe the distant or deeply dust-enshrouded regions of the Universe, investigating the history of star and planet formation from the earliest universe to the present day. To enable this the instrument optical module must be cooled below 7K, presenting specific challenges for the environmental testing and calibration activities. The assembly, integration and verification (AIV) activities for the proto-flight model (pFM) instrument ran from March 2010 to May 2012 at RAL where the instrument has been put through a full suite of environmental and performance tests with a non-conventional single cryo-test approach. In this paper we present an overview of the testing conducted on the MIRI pFM including ambient alignment testing, vibration testing, gravity release testing, cryogenic performance and calibration testing, functional testing at ambient and operational temperatures, thermal balance tests, and Electro-Magnetic Compatibility (EMC) testing. We discuss how tests were planned and managed to ensure that the whole AIV process remained on schedule and give an insight into the lessons learned from this process. We also show how the process of requirement verification for this complex system was managed and documented. We describe how the risks associated with a single long duration test at operating temperature were controlled so that the complete suite of environmental tests could be used to build up a full picture of instrument compliance.

National Centers for Environmental Prediction

Science.gov Websites

Organization Search Enter text Search Navigation Bar End Cap Search EMC Go Branches Global Climate and Weather / VISION | About EMC EMC > GLOBAL BRANCH > GFS > HOME Home Implementations Documentation References Products Model Guidance Performance Developers VLab GLOBAL FORECAST SYSTEM Global Data

Enamel microcracks in terms of orthodontic treatment: A novel method for their detection and evaluation.

PubMed

Dumbryte, Irma; Linkeviciene, Laura; Linkevicius, Tomas; Malinauskas, Mangirdas

2017-07-26

The study aimed at introducing current available techniques for enamel microcracks (EMCs) detection, and presenting a method for direct quantitative analysis of an individual EMC. Measurements of the detailed EMCs characteristics (location, length, and width) were taken from the reconstructed images of the buccal tooth surface (teeth extracted from two age groups of patients) employing a scanning electron microscopy (SEM) and our derived formulas before and after ceramic brackets removal. Measured parameters of EMCs for younger age group were 2.41 µm (width), 3.68 mm (length) before and 2.73 µm, 3.90 mm after debonding; for older -4.03 µm, 4.35 mm before and 4.80 µm, 4.37 mm after brackets removal. Following debonding EMCs increased for both groups, however the changes in width and length were statistically insignificant. Regardless of the age group, proposed method enabled precise detection of the same EMC before and after debonding, and quantitative examination of its characteristics.

Primary extraskeletal myxoid chondrosarcoma of the vulva.

PubMed

Sawada, Morio; Tochigi, Naobumi; Sasajima, Yuko; Hasegawa, Tadashi; Kasamatsu, Takahiro; Kitawaki, Jo

2011-11-01

Primary extraskeletal myxoid chondrosarcoma (EMC) of the vulva is extremely rare. There is little available information about the biological behavior and treatment strategy for primary EMC of the vulva. We report a rare case of primary EMC of the vulva treated surgically. A 24-year-old Japanese woman had demonstrated a small and elastic mass of the vulva and underwent enucleation of the mass at a previous hospital, but a definitive histopathological diagnosis was not obtained. Therefore, the patient was referred to our hospital for further evaluation and treatment. We histopathologically diagnosed the tumor as primary EMC of the vulva and performed vulvectomy with vulvoperineal reconstruction. Microscopic examination of the resected specimens demonstrated residual tumor nodules of EMC. However, there were no viable tumor cells at the surgical margin. Approximately two years after wide local excision was performed, the patient is doing well and there is no apparent recurrence of EMC. © 2011 The Authors. Journal of Obstetrics and Gynaecology Research © 2011 Japan Society of Obstetrics and Gynecology.

EMCS Experiment Container Replacement

NASA Image and Video Library

2018-01-26

iss054e023797 (Jan. 26, 2018) --- NASA astronaut Joe Acaba with an Experiment Container (EC) to begin the Plant Gravity Perception experiment, testing the gravity-sensing ability of plants in microgravity.

Measurement of the EMC effect in the deuteron

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffioen, Keith A.; Arrington, John R.; Christy, M. Eric

2015-07-21

We have determined the structure function ratiomore » $$R^d_{\\rm EMC}=F_2^d/(F_2^n+F_2^p)$$ from recently published $$F_2^n/F_2^d$$ data taken by the BONuS experiment using CLAS at Jefferson Lab. This ratio deviates from unity, with a slope $$dR_{\\rm EMC}^{d}/dx= -0.10\\pm 0.05$$ in the range of Bjorken $x$ from 0.35 to 0.7, for invariant mass $W>1.4$ GeV and $Q^2>1$ GeV$^2$. The observed EMC effect for these kinematics is consistent with conventional nuclear physics models that include off-shell corrections, as well as with empirical analyses that find the EMC effect proportional to the probability of short-range nucleon-nucleon correlations.« less

Cell host response to infection with novel human coronavirus EMC predicts potential antivirals and important differences with SARS coronavirus.

PubMed

Josset, Laurence; Menachery, Vineet D; Gralinski, Lisa E; Agnihothram, Sudhakar; Sova, Pavel; Carter, Victoria S; Yount, Boyd L; Graham, Rachel L; Baric, Ralph S; Katze, Michael G

2013-04-30

A novel human coronavirus (HCoV-EMC) was recently identified in the Middle East as the causative agent of a severe acute respiratory syndrome (SARS) resembling the illness caused by SARS coronavirus (SARS-CoV). Although derived from the CoV family, the two viruses are genetically distinct and do not use the same receptor. Here, we investigated whether HCoV-EMC and SARS-CoV induce similar or distinct host responses after infection of a human lung epithelial cell line. HCoV-EMC was able to replicate as efficiently as SARS-CoV in Calu-3 cells and similarly induced minimal transcriptomic changes before 12 h postinfection. Later in infection, HCoV-EMC induced a massive dysregulation of the host transcriptome, to a much greater extent than SARS-CoV. Both viruses induced a similar activation of pattern recognition receptors and the interleukin 17 (IL-17) pathway, but HCoV-EMC specifically down-regulated the expression of several genes within the antigen presentation pathway, including both type I and II major histocompatibility complex (MHC) genes. This could have an important impact on the ability of the host to mount an adaptive host response. A unique set of 207 genes was dysregulated early and permanently throughout infection with HCoV-EMC, and was used in a computational screen to predict potential antiviral compounds, including kinase inhibitors and glucocorticoids. Overall, HCoV-EMC and SARS-CoV elicit distinct host gene expression responses, which might impact in vivo pathogenesis and could orient therapeutic strategies against that emergent virus. Identification of a novel coronavirus causing fatal respiratory infection in humans raises concerns about a possible widespread outbreak of severe respiratory infection similar to the one caused by SARS-CoV. Using a human lung epithelial cell line and global transcriptomic profiling, we identified differences in the host response between HCoV-EMC and SARS-CoV. This enables rapid assessment of viral properties and the ability to anticipate possible differences in human clinical responses to HCoV-EMC and SARS-CoV. We used this information to predict potential effective drugs against HCoV-EMC, a method that could be more generally used to identify candidate therapeutics in future disease outbreaks. These data will help to generate hypotheses and make rapid advancements in characterizing this new virus.

Advanced Stirling Convertor Durability Testing: Plans and Interim Results

NASA Technical Reports Server (NTRS)

Meer, David W.; Oriti, Salvatore M.

2012-01-01

The U.S. Department of Energy (DOE), Lockheed Martin Corporation (LM), and NASA Glenn Research Center (GRC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. In support of this program, GRC has been involved in testing Stirling convertors, including the Advanced Stirling Convertor (ASC), for use in the ASRG. This testing includes electromagnetic interference/compatibility (EMI/EMC), structural dynamics, advanced materials, organics, and unattended extended operation. The purpose of the durability tests is to experimentally demonstrate the margins in the ASC design. Due to the high value of the hardware, previous ASC tests focused on establishing baseline performance of the convertors within the nominal operating conditions. The durability tests present the first planned extension of the operating conditions into regions beyond those intended to meet the product spec, where the possibility exists of lateral contact, overstroke, or over-temperature events. These tests are not intended to cause damage that would shorten the life of the convertors, so they can transition into extended operation at the conclusion of the tests. This paper describes the four tests included in the durability test sequence: 1) start/stop cycling, 2) exposure to constant acceleration in the lateral and axial directions, 3) random vibration at increased piston amplitude to induce contact events, and 4) overstroke testing to simulate potential failures during processing or during the mission life where contact events could occur. The paper also summarizes the analysis and simulation used to predict the results of each of these tests.

Performance of thin-film ferroelectric capacitors for EMC decoupling.

PubMed

Li, Huadong; Subramanyam, Guru

2008-12-01

This paper studied the effects of thin-film ferroelectrics as decoupling capacitors for electromagnetic compatibility applications. The impedance and insertion loss of PZT capacitors were measured and compared with the results from commercial off-the-shelf capacitors. An equivalent circuit model was extracted from the experimental results, and a considerable series resistance was found to exist in ferroelectric capacitors. This resistance gives rise to the observed performance difference around series resonance between ferroelectric PZT capacitors and normal capacitors. Measurements on paraelectric (Ba,Sr)TiO(3)-based integrated varactors do not show this significant resistance. Some analyses were made to investigate the mechanisms, and it was found that it can be due to the hysteresis in the ferroelectric thin films.

Absorber for microwave investigation in the open space

NASA Astrophysics Data System (ADS)

Kubacki, Roman; Smólski, Bogusław; Głuszewski, Wojciech; Przesmycki, Rafał; Rudyk, Karol

2017-04-01

In some circumstances there is a need to realize the Electromagnetic Compatibility (EMC) investigation not in the specialized anechoic chamber but in the open space. Typical absorbers used in anechoic chamber to reduce the reflected rays from walls and floor, such as ferrite plates and graphite cones, are not suitable in the open space. In the work the investigation of the flexible absorbing material intended to the liquidation of the radiation reflected from the ground has been presented. As an absorbing material the metallic-glass with graphite was elaborated. This material was additionally exposed to the ionizing radiation in the dose of 100 kGy in the radioactive gamma source. The permittivity, permeability as well as the shielding properties have been analyzed.

Electronically tunable phase locked loop oscillator

NASA Astrophysics Data System (ADS)

Balasis, M.; Davis, M. R.; Jackson, C. R.

1982-02-01

This report describes the design and development of a low noise, high power, variable oscillator incorporating a high 'Q' electronically tunable resonator as the frequency determining element. The VCO provides improved EMC performance in phase locked synthesizers which are a part of communications equipments. The oscillator combines a low noise VMOS transistor with the selectivity and out-of-band attenuation of a coaxial resonator to provide superior EMC performance. Several oscillator designs were examined and the basis for the final configuration is presented. Oscillator noise is discussed and models for analysis are explained. A brass board model was constructed and tested and the technical results are presented.

An Attempt to Compare EMCS with TOXLINE.

ERIC Educational Resources Information Center

Lorent, Jean-Pierre; Schirner, Hedi

1978-01-01

Sixteen queries, performed on the two systems, resulted in 247 unique relevant references from EMCS and 559 from TOXLINE. The overlap varied considerably, from 6 to 50 percent. It is remarkable that TOXLINE, with nine subfiles specially compiled for toxicology, can be supplemented by EMCS, which in the present study delivered 31 percent of all the…

Interactive color-graphics interface for energy-monitoring and -control systems. Final report, October 1979-September 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Canfield, K.J.

1984-05-01

An EMCS (Energy Monitoring and Control System) can be described as a system that automatically takes care of routine operation of equipment and provides centralized reporting and override capabilities. Equipment controlled by an EMCS would be heating, ventilating, and air conditioning (HVAC) equipment, air compressors, and small package boiler units. The EMCS would obtain raw information (data) from sensors associated with the equipment and massage the data into useful information. The information obtained from the sensors plus additional information available to the EMCS would be used to control the equipment. The information would also be available to the operator inmore » the form of reports or in response to operator commands for specific information. EMCS are computerized systems that control and monitor energy consuming and producing equipment at Naval facilities. The larger systems have been installed with color-graphics cathode ray tube operator consoles to provide better information to the personnel operating these systems. This report summarizes the work done on defining an adequate operator console and recommends changes to the existing EMCS Guide Specifications.« less

Final Results for the GRC Supporting Technology Development Project for the 110-Watt Stirling Radioisotope Generator (SRG110)

NASA Technical Reports Server (NTRS)

Schreiber, Jeffrey G.; Thieme, Lanny G.

2007-01-01

From 1999 to 2006, the NASA Glenn Research Center (GRC) supported the development of a high-efficiency, nominal 110-We Stirling Radioisotope Generator (SRG110) for potential use on NASA missions, including deep space missions, Mars rovers, and lunar applications. Lockheed Martin (LM) was the system integrator for the SRG110, under contract to the Department of Energy (DOE). Infinia Corporation (formerly Stirling Technology Company) developed the Stirling convertor, first as a contractor to DOE and then under subcontract to LM. The SRG110 development has been redirected, and recent program changes have been made to significantly increase the specific power of the generator. System development of an Advanced Stirling Radioisotope Generator (ASRG) has now begun, using a lightweight, advanced convertor from Sunpower, Inc. This paper summarizes the results of the supporting technology effort that GRC completed for the SRG110. GRC tasks included convertor extended-duration testing in air and thermal vacuum environments, heater head life assessment, materials studies, permanent magnet aging characterization, linear alternator evaluations, structural dynamics testing, electromagnetic interference (EMI) and electromagnetic compatibility (EMC) characterization, organic materials evaluations, reliability studies, and development of an end-to-end system dynamic model. Related efforts are now continuing in many of these areas to support ASRG development.

Final Results for the GRC Supporting Technology Development Project for the 110-Watt Stirling Radioisotope Generator (SRG110)

NASA Technical Reports Server (NTRS)

Schreiber, Jeffrey G.; Thieme, Lanny G.

2007-01-01

From 1999-2006, the NASA Glenn Research Center (GRC) supported the development of a high-efficiency, nominal 110-We Stirling Radioisotope Generator (SRG110) for potential use on NASA missions, including deep space missions, Mars rovers, and lunar applications. Lockheed Martin (LM) was the system integrator for the SRG110, under contract to the Department of Energy (DOE). Infinia Corporation (formerly Stirling Technology Company) developed the Stirling convertor, first as a contractor to DOE and then under subcontract to LM. The SRG110 development has been redirected, and recent program changes have been made to significantly increase the specific power of the generator. System development of an Advanced Stirling Radioisotope Generator (ASRG) has now begun, using a lightweight, advanced convertor from Sunpower, Inc. This paper summarizes the results of the supporting technology effort that GRC completed for the SRG110. GRC tasks included convertor extended-duration testing in air and thermal vacuum environments, heater head life assessment, materials studies, permanent magnet aging characterization, linear alternator evaluations, structural dynamics testing, electromagnetic interference (EMI) and electromagnetic compatibility (EMC) characterization, organic materials evaluations, reliability studies, and development of an end-to-end system dynamic model. Related efforts are now continuing in many of these areas to support ASRG development.

International trends in electronic media communication among 11- to 15-year-olds in 30 countries from 2002 to 2010: association with ease of communication with friends of the opposite sex.

PubMed

Boniel-Nissim, Meyran; Lenzi, Michela; Zsiros, Emese; de Matos, Margarida Gaspar; Gommans, Rob; Harel-Fisch, Yossi; Djalovski, Amir; van der Sluijs, Winfried

2015-04-01

Electronic media has become a central part of the lives of adolescents. Therefore, this study examines trends in adolescent electronic media communication (EMC) and its relationship with ease of communication with friends of the opposite sex, from 2002 to 10 in 30 European and North American regions. Data from the HBSC study were collected using self-report questionnaires from 11-, 13- and 15-year-old participants (N = 404 523). EMC use has grown over the years in most of these regions and increases with age. Even though Internet usage is often blamed for its negative effects on teenagers' social interactions in the physical world, in this study EMC was found to predict ease of communication with friends. Especially, the more they use EMC, the easier they find it to talk with friends of the opposite sex. Although these findings suggest that EMC reinforces communication, the interaction between year (2002-2006-2010) and EMC usage was not significant. This finding contradicts research that suggests that EMC contributes to loneliness and isolation, and supports other studies that present electronic media as a powerful tool for helping to connect people. © The Author 2015. Published by Oxford University Press on behalf of the European Public Health Association. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Kee Sung; Rajput, Nav Nidhi; Persson, Kristin A.

Ferrocene (Fc) and N-(ferrocenylmethyl)-N,N-dimethyl-N-ethylammonium bistrifluoromethyl-sulfonimide (Fc1N112-TFSI) were dissolved in carbonate solvents and self-diffusion coefficients (D) of solutes and solvents were measured by {sup 1}H and {sup 19}F pulsed field gradient nuclear magnetic resonance (NMR) spectroscopy. The organic solvents were propylene carbonate (PC), ethyl methyl carbonate (EMC), and a ternary mixture that also includes ethylene carbonate (EC). Results from NMR studies over the temperature range of 0–50 °C and for various concentrations (0.25–1.7 M) of Fc1N112-TFSI are compared to values of D simulated with classical molecular dynamics (MD). The measured self-diffusion coefficients gradually decreased as the Fc1N112-TFSI concentration increased in allmore » solvents. Since TFSI{sup −} has fluoromethyl groups (CF{sub 3}), D{sub TFSI} could be measured separately and the values found are larger than those for D{sub Fc1N112} in all samples measured. The EC, PC, and EMC have the same D in the neat solvent mixture and when Fc is dissolved in EC/PC/EMC at a concentration of 0.2 M, probably due to the interactions between common carbonyl structures within EC, PC, and EMC. A difference in D (D{sub PC} < D{sub EC} < D{sub EMC}), and both a higher E{sub a} for translational motion and higher effective viscosity for PC in the mixture containing Fc1N112-TFSI reflect the interaction between PC and Fc1N112{sup +}, which is a relatively stronger interaction than that between Fc1N112{sup +} and other solvent species. In the EC/PC/EMC solution that is saturated with Fc1N112-TFSI, we find that D{sub PC} = D{sub EC} = D{sub EMC} and Fc1N112{sup +} and all components of the EC/PC/EMC solution have the same E{sub a} for translational motion, while the ratio D{sub EC/PC/EMC}/D{sub Fc1N112} is approximately 3. These results reflect the lack of available free volume for independent diffusion in the saturated solution. The Fc1N112{sup +} transference numbers lie around 0.4 and increase slightly as the temperature is increased in the PC and EMC solvents. The trends observed for D from simulations are in good agreement with experimental results and provide molecular level understanding of the solvation structure of Fc1N112-TFSI dissolved in EC/PC/EMC.« less

Flight Hardware Packaging Design for Stringent EMC Radiated Emission Requirements

NASA Technical Reports Server (NTRS)

Lortz, Charlene L.; Huang, Chi-Chien N.; Ravich, Joshua A.; Steiner, Carl N.

2013-01-01

This packaging design approach can help heritage hardware meet a flight project's stringent EMC radiated emissions requirement. The approach requires only minor modifications to a hardware's chassis and mainly concentrates on its connector interfaces. The solution is to raise the surface area where the connector is mounted by a few millimeters using a pedestal, and then wrapping with conductive tape from the cable backshell down to the surface-mounted connector. This design approach has been applied to JPL flight project subsystems. The EMC radiated emissions requirements for flight projects can vary from benign to mission critical. If the project's EMC requirements are stringent, the best approach to meet EMC requirements would be to design an EMC control program for the project early on and implement EMC design techniques starting with the circuit board layout. This is the ideal scenario for hardware that is built from scratch. Implementation of EMC radiated emissions mitigation techniques can mature as the design progresses, with minimal impact to the design cycle. The real challenge exists for hardware that is planned to be flown following a built-to-print approach, in which heritage hardware from a past project with a different set of requirements is expected to perform satisfactorily for a new project. With acceptance of heritage, the design would already be established (circuit board layout and components have already been pre-determined), and hence any radiated emissions mitigation techniques would only be applicable at the packaging level. The key is to take a heritage design with its known radiated emissions spectrum and repackage, or modify its chassis design so that it would have a better chance of meeting the new project s radiated emissions requirements.

Cell Host Response to Infection with Novel Human Coronavirus EMC Predicts Potential Antivirals and Important Differences with SARS Coronavirus

PubMed Central

Josset, Laurence; Menachery, Vineet D.; Gralinski, Lisa E.; Agnihothram, Sudhakar; Sova, Pavel; Carter, Victoria S.; Yount, Boyd L.; Graham, Rachel L.; Baric, Ralph S.; Katze, Michael G.

2013-01-01

ABSTRACT A novel human coronavirus (HCoV-EMC) was recently identified in the Middle East as the causative agent of a severe acute respiratory syndrome (SARS) resembling the illness caused by SARS coronavirus (SARS-CoV). Although derived from the CoV family, the two viruses are genetically distinct and do not use the same receptor. Here, we investigated whether HCoV-EMC and SARS-CoV induce similar or distinct host responses after infection of a human lung epithelial cell line. HCoV-EMC was able to replicate as efficiently as SARS-CoV in Calu-3 cells and similarly induced minimal transcriptomic changes before 12 h postinfection. Later in infection, HCoV-EMC induced a massive dysregulation of the host transcriptome, to a much greater extent than SARS-CoV. Both viruses induced a similar activation of pattern recognition receptors and the interleukin 17 (IL-17) pathway, but HCoV-EMC specifically down-regulated the expression of several genes within the antigen presentation pathway, including both type I and II major histocompatibility complex (MHC) genes. This could have an important impact on the ability of the host to mount an adaptive host response. A unique set of 207 genes was dysregulated early and permanently throughout infection with HCoV-EMC, and was used in a computational screen to predict potential antiviral compounds, including kinase inhibitors and glucocorticoids. Overall, HCoV-EMC and SARS-CoV elicit distinct host gene expression responses, which might impact in vivo pathogenesis and could orient therapeutic strategies against that emergent virus. PMID:23631916

The Effects of Simulated Weightlessness on Susceptibility to Viral and Bacterial Infections Using a Murine Model

NASA Technical Reports Server (NTRS)

Gould, C. L.

1985-01-01

Certain immunological responses may be compromised as a result of changes in environmental conditions, such as the physiological adaptation to and from the weightlessness which occurs during space flight and recovery. A murine antiorthostatic model was developed to simulate weightlessness. Using this model, the proposed study will determine if differences in susceptibility to viral and bacterial infections exist among mice suspended in an antiorthostatic orientation to simulate weightlessness, mice suspended in an orthostatic orientation to provide a stressful situation without the condition of weightlessness simulation, and non-suspended control mice. Inbred mouse strains which are resistant to the diabetogenic effects of the D variant of encephalomyocarditis virus (EMC-D) and the lethal effects of Salmonella typhimurium will be evaluated. Glucose tolerance tests will be performed on all EMC-D-infected and non-infected control groups. The incidence of EMC-D-induced diabetes and the percentage survival of S. typhimurium-infected animals will be determined in each group. An additional study will determine the effects of simulated weightlessness on murine responses to exogenous interferon.

Interface Modification of Bernal- and Rhombohedral-Stacked Trilayer-Graphene/Metal Electrode on Resistive Switching of Silver Electrochemical Metallization Cells.

PubMed

Wang, Jer-Chyi; Chan, Ya-Ting; Chen, Wei-Fan; Wu, Ming-Chung; Lai, Chao-Sung

2017-10-25

Bernal- and rhombohedral-stacked trilayer graphene (B- and r-TLG) on nickel (Ni) and iridium (Ir) films acting as bottom electrodes (BEs) of silver electrochemical metallization cells (Ag-EMCs) have been investigated in this study. Prior to the fabrication of the EMC devices, Raman mapping and atomic force microscopy are applied to identify the B- and r-TLG sheets, with the latter revealing a significant D peak and a rough surface for the Ir film. The Ag-EMCs with the stacked BE of r-TLG on the Ir film show a conductive mechanism of Schottky emission at the positive top electrode bias for both high- and low-resistance states that can be examined by the resistance change with the device area and are modulated by pulse bias operation. Thus, an effective electron barrier height of 0.262 eV at the r-TLG and Ir interface is obtained because of the conspicuous energy gap of r-TLG on the Ir film and the van der Waals (vdW) gap between the r-TLG and Ir contact metal. With the use of Ni instead of Ir contact metal, the Ag-EMCs with TLG BE demonstrate +0.3 V/-0.75 V operation voltages, more than 10 4 s data retention at 115 °C and 250 times endurance testing, making the TLG sheets suitable for low-power nonvolatile memory applications on flexible substrates.

National Centers for Environmental Prediction

Science.gov Websites

Skip Navigation Links www.nws.noaa.gov NOAA logo - Click to go to the NOAA homepage National Weather Service NWS logo - Click to go to the NWS homepage EMC Logo Navigation Bar Left Cap Home News Publications EMC Facebook Contact EMC Webmaster logo image for USA dot gov website. USA dot gov is the U.S

Epithelial-myoepithelial carcinoma metastasis to the thoracic spine.

PubMed

Goodwin, C Rory; Khattab, Mohamed H; Sankey, Eric W; Crane, Genevieve M; McCarthy, Edward F; Sciubba, Daniel M

2016-02-01

Epithelial-myoepithelial carcinoma (EMC) is a very rare salivary gland malignancy accounting for less than 1% of salivary gland tumors, and classically arises from the parotid gland in females. Spinal cord compression caused by EMC metastasized from the parotid gland has only been described once in the literature to our knowledge. We report the first case of a patient with parotid EMC spinal metastasis undergoing a gross total resection with instrumented fusion. This case illustrates that an en bloc resection with a planned transgression through the spinal canal may be a reasonable option for EMC metastasized to the spine. Copyright © 2015 Elsevier Ltd. All rights reserved.

ESA hardware for plant research on the International Space Station

NASA Astrophysics Data System (ADS)

Brinckmann, E.

The long awaited launch of the European Modular Cultivation System (EMCS) will provide a platform on which long-term and shorter experiments with plants will be performed on the International Space Station (ISS). EMCS is equipped with two centrifuge rotors (600 mm diameter), which can be used for in-flight 1 g controls and for studies with acceleration levels from 0.001 g to 2.0 g. Several experiments are in preparation investigating gravity relating to gene expression, gravisensing and phototropism of Arabidopsis thaliana and lentil roots. The experiment-specific hardware provides growth chambers for seedlings and whole A. thaliana plants and is connected to the EMCS Life Support System. Besides in-flight video observation, the experiments will be evaluated post-flight by means of fixed or frozen material. EMCS will have for the first time the possibility to fix samples on the rotating centrifuge, allowing a detailed analysis of the process of gravisensing. About two years after the EMCS launch, ESA's Biolab will be launched in the European "Columbus" Module. In a similar way as in EMCS, Biolab will accommodate experiments with plant seedlings and automatic fixation processes on the centrifuge. The hardware concepts for these experiments are presented in this communication.

New Developments in Spaceflight Hardware for Plant Research

NASA Astrophysics Data System (ADS)

Brinckmann, E.

The long awaited launch of the European Modular Cultivation System (EMCS) will provide a platform to perform long term and shorter experiments with plants on the International Space Station (ISS). EMCS is equipped with two centrifuge rotors (600 mm diameter), which can be used for flight 1xg controls and for studies with accelerations from 0.001xg to 2.0xg. Several experiments are in preparation, investigating gravity related gene expressions, gravisensing and phototropism of Arabidopsis thaliana, fern spores and lentil rots. The experiment specific hardware provides growth chambers for seedlings and whole A. thaliana plants, connected to the EMCS Life Support System. Besides video observation, the experiments will be evaluated on ground by means of fixed or frozen material. EMCS will have for the first time the possibility to fix samples on the rotating centrifuge, allowing a detailed analysis of the process of gravisensing. Two years after EMCS, ESA's BIOLAB will be launched in the European "Columbus" Module. In a similar way as in EMCS, BIOLAB accommodates experiments with plant seedlings and automatic fixation processes on the centrifuge. The hardware concepts for these experiments will be presented in this communication.

Overview and comparative study of GPR international standards and guidelines - COST Action TU1208

NASA Astrophysics Data System (ADS)

Pajewski, Lara; Marciniak, Marian; Benedetto, Andrea; Tosti, Fabio

2016-04-01

Ground Penetrating Radar (GPR) can be effectively used for non-destructive testing of composite structures and diagnostics affecting the whole life-cycle of civil engineering works. Nevertheless, few recognised international standards exist in this field and inhomogeneous recommendations are present in different countries. Moreover, the levels of knowledge, awareness and experience regarding the use of GPR in civil engineering vary strongly across different European areas. The COST Action TU1208 is working hard on leveraging these differences, by sharing and disseminating knowledge and experience, as well as by developing guidelines and protocols for a safe and effective use of GPR in civil engineering. GPR users need to know which is the best way to conduct GPR measurements and what the quality level for the results should be. The TU1208 guidelines will ensure a higher efficiency and quality of GPR services and they will constitute a scientific basis for the introduction of European Standards on the application of GPR in civil engineering. The aim of this contribution is to present an in-depth overview and critical analysis of the existing GPR international and national standards and guidelines. The main documents considered in our work are listed and briefly described in the following. Three standards are provided by the American Society for Testing and Materials (ASTM), to guide the GPR use for subsurface investigation, evaluation of asphalt-covered concrete bridge decks, and determination of pavement-layer thickness: 1. ASTM D6432-11, Standard Guide for Using the Surface Ground Penetrating Radar Method for Subsurface Investigation, ASTM International, West Conshohocken, PA, 2011, www.astm.org, DOI: 10.1520/D6432-11. 2. ASTM D6087-08, Standard Test Method for Evaluating Asphalt-Covered Concrete Bridge Decks Using Ground Penetrating Radar, ASTM International, West Conshohocken, PA, 2008, www.astm.org, DOI: 10.1520/D6087-08. 3. ASTM D4748-10, Standard Test Method for Determining the Thickness of Bound Pavement Layers Using Short-Pulse Radar, ASTM International, West Conshohocken, PA, 2010, www.astm.org, DOI: 10.1520/D4748-10. Further ASTM standards exist, not focused on GPR but including useful information (details are not provided here, for brevity reasons). There are no standards in Europe, instead, guiding the GPR use for subsurface prospecting and regulating the numerous applications of this non-destructive technique. The following Radio and Telecommunications Terminal Equipment (R&TTE) directive applies to GPR equipment and allows the placing of a GPR product on the European (EU) market for sale: Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999, on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. Official Journal of the European Union, L 91, 7.4.1999, open access on ec.europa.eu. This document will be repealed, since 13 June 2016, by the following R&TTE directive: Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014, on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment, repealing Directive 1999/5/EC. Official Journal of the European Union, L 153, 22.5.2014, open access on ec.europa. Although conformance to the R&TTE directive allows the placing of a GPR product on the market for sale, it does not give authority for its use. In order to use the equipment, in the majority of EU member countries, a license is required. The license is controlled and issued by the radio administration in each of the member countries. The Electronic Communications Committee (ECC) of the European Conference of Postal and Telecommunications Administrations (CEPT) considers and develops policies on electronic communications activities in European context, taking account of European and international legislations and regulations. There are 48 European countries involved in the CEPT, which cooperate to regulate posts, radio spectrum and communications networks in Europe. The ECC agreed to the decision ECC/DEC/(06)08, specifically referred to GPR and Wall Penetrating Radar (WPR) systems: ECC Decision of 1 December 2006 on the conditions for use of the radio spectrum by Ground- and Wall- Probing Radar (GPR/WPR) imaging systems, 14 December 2006, open access on www.cept.org. This is not legally binding on member countries. It is currently implemented by 25 and partly implemented by 2 of the 48 administrations; 5 further administration are considering and studying the decision. Outside Europe, different approaches exist, ranging from very formal technical approval and licensing conditions to no specific rules. A series of standards and codes, introduced by the European Telecommunications Standards Institute (ETSI), regulate the GPR use and its emissions of electromagnetic radiation in Europe: 1. ETSI EN 301 489-1 v1.9.2, Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements, Sept. 2011, open access on www.etsi.org, Ref. DEN/ERM-EMC-230-32, 45 pp. [7]. This document is a Harmonized European Standard. 2. ETSI EN 301 489-32 v1.1.1, Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 32: Specific conditions for Ground and Wall Probing Radar applications, Sept. 2009, open access on www.etsi.org, Ref. DEN/ERM-EMC-230-32, 12 pp. [8]. This document is currently (May 2015) a Candidate Harmonized European Standard (Telecommunication Series). 3. ETSI EN 302/066-1 v1.2.1, Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground- and Wall- Probing Radar applications (GPR/WPR) imaging systems; Part 1: Technical characteristics and test methods, Dec. 2007, open access on www.etsi.org, Ref. REN/ERM-TG31A-0113-1, 25 pp. [9]. This document is a Harmonized European Standard (Telecommunications series). 4. ETSI EN 302/066-2 v1.2.1, Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground- and Wall- Probing Radar applications (GPR/WPR) imaging systems; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive, Dec. 2007, open access on www.etsi.org, Ref. REN/ERM-TG31A-0113-2, 12 pp. [10]. This document is a Harmonized European Standard (Telecommunications series). 5. ETSI EG 202 730 v1.1.1, Electromagnetic compatibility and Radio spectrum Matters (ERM); Code of Practice in respect of the control, use and application of Ground Probing Radar (GPR) and Wall Probing Radar (WPR) systems and equipment, Sept. 2009, open access on www.etsi.org, Ref. DEG/ERM-TGUWB-010, 11 pp. [11]. This document is currently (May 2015) an ETSI guide. Few National GPR Guidelines and Standards exist in Europe. In France, the National standard NF S 70-003, Parts 1-3, is concerned with the use of GPR to detect buried utilities. Still in France, Cerema/Ifsttar produced protocols for road inspection. In Germany, the DGZfP e.V. (German Society for Non-Destructive Testing) published a fact sheet called "Merkblatt B10" on the radar method for non-destructive testing in civil engineering (2008). Still in Germany, there is a BASt (Federal Highway Administration) instruction sheet on the use of GPR to gain inventory data of road structure (2003). In Poland, the national regulation of September 24, 1998 (Dz.U. Nr 126 poz. 839) cites 'georadar testing' as a method to investigate the soil structure. In Scandinavia, recommendations for guidelines were developed during the MARA NORD Project (2010-2012) on the use of GPR in asphalt air voids content measurements, in road construction quality control, in bridge deck surveys, in road rehabilitation projects and in site investigations. Acknowledgement This work stems from the research activities of COST (European COoperation in Science and Technology) Action TU1208 "Civil engineering applications of Ground Penetrating Radar." The Authors thank COST (www.cost.eu) for funding the Action TU1208 (www.GPRadar.eu). Part of this work was carried out during the Short-Term Scientific Mission STSM-TU1208-24656 "Comparative study of GPR international standards and guidelines" (Dr Lara Pajewski, Italy, visiting Prof Marian Marciniak, Poland).

Ground Testing of the EMCS Seed Cassette for Biocompatibility with the Cellular Slime Mold, Dictyostelium Discoideum

NASA Technical Reports Server (NTRS)

Hanely, Julia C.; Reinsch, Sigrid; Myers, Zachary A.; Freeman, John; Steele, Marianne K.; Sun, Gwo-Shing; Heathcote, David G.

2014-01-01

The European Modular Cultivation System, EMCS, was developed by ESA for plant experiments. To expand the use of flight verified hardware for various model organisms, we performed ground experiments to determine whether ARC EMCS Seed Cassettes could be adapted for use with cellular slime mold for future space flight experiments. Dictyostelium is a cellular slime mold that can exist both as a single-celled independent organism and as a part of a multicellular colony which functions as a unit (pseudoplasmodium). Under certain stress conditions, individual amoebae will aggregate to form multicellular structures. Developmental pathways are very similar to those found in Eukaryotic organisms, making this a uniquely interesting organism for use in genetic studies. Dictyostelium has been used as a genetic model organism for prior space flight experiments. Due to the formation of spores that are resistant to unfavorable conditions such as desiccation, Dictyostelium is also a good candidate for use in the EMCS Seed Cassettes. The growth substratum in the cassettes is a gridded polyether sulfone (PES) membrane. A blotter beneath the PES membranes contains dried growth medium. The goals of this study were to (1) verify that Dictyostelium are capable of normal growth and development on PES membranes, (2) develop a method for dehydration of Dictyostelium spores with successful recovery and development after rehydration, and (3) successful mock rehydration experiments in cassettes. Our results show normal developmental progression in two strains of Dictyostelium discoideum on PES membranes with a bacterial food source. We have successfully performed a mock rehydration of spores with developmental progression from aggregation to slug formation, and production of morphologically normal spores within 9 days of rehydration. Our results indicate that experiments on the ISS using the slime mold, Dictyostelium discoideum could potentially be performed in the flight verified hardware of the EMCS ARC Seed Cassettes.

Dynamically Movable Exhausting Emc Sealing System

DOEpatents

Barringer, Dennis R.; Seminaro, Edward J.; Toffler, Harold M.

2003-12-09

A docking apparatus for printed circuit boards including a cassette housing, having a housing base, a housing cover and a housing wall, wherein the housing base and the housing wall are disposed relative to each other so as to define a housing cavity for containing a printed circuit card and wherein the housing wall includes a cable opening disposed so as to be communicated with the housing cavity, a housing bezel, disposed relative to the cassette housing so as to be associated with the cable opening, the housing bezel includes an outer bezel having a first plurality of openings and an inner bezel having a second plurality of apertures, the inner bezel in electrical communication with the printed circuit card, wherein said housing bezel is removable, and an EMC gasket disposed between the outer and inner bezels of said housing bezel, the EMC gasket configured to provide a removable EMC seal proximate the cable opening while still allowing airflow through the first and second plurality of apertures having the EMC gasket therebetween. A docking apparatus for printed circuit boards including a cassette housing, having a housing base, a housing cover and a housing wall, wherein the housing base and the housing wall are disposed relative to each other so as to define a housing cavity for containing a printed circuit card and wherein the housing wall includes a cable opening disposed so as to be communicated with the housing cavity, a housing bezel, disposed relative to the cassette housing so as to be associated with the cable opening, the housing bezel includes an outer bezel having a first plurality of openings and an inner bezel having a second plurality of apertures, the inner bezel in electrical communication with the printed circuit card, wherein said housing bezel is removable, and an EMC gasket disposed between the outer and inner bezels of said housing bezel, the EMC gasket configured to provide a removable EMC seal proximate the cable opening while still allowing airflow through the first and second plurality of apertures having the EMC gasket therebetween.

Lithium-Ion Electrolytes with Improved Safety Tolerance to High Voltage Systems

NASA Technical Reports Server (NTRS)

Smart, Marshall C. (Inventor); Prakash, Surya G. (Inventor); Bugga, Ratnakumar V. (Inventor); Krause, Frederick C. (Inventor)

2015-01-01

The invention discloses various embodiments of electrolytes for use in lithium-ion batteries, the electrolytes having improved safety and the ability to operate with high capacity anodes and high voltage cathodes. In one embodiment there is provided an electrolyte for use in a lithium-ion battery comprising an anode and a high voltage cathode. The electrolyte has a mixture of a cyclic carbonate of ethylene carbonate (EC) or mono-fluoroethylene carbonate (FEC) co-solvent, ethyl methyl carbonate (EMC), a flame retardant additive, a lithium salt, and an electrolyte additive that improves compatibility and performance of the lithium-ion battery with a high voltage cathode. The lithium-ion battery is charged to a voltage in a range of from about 2.0 V (Volts) to about 5.0 V (Volts).

Utilizing ARC EMCS Seedling Cassettes as Highly Versatile Miniature Growth Chambers for Model Organism Experiments

NASA Technical Reports Server (NTRS)

Freeman, John L.; Steele, Marianne K.; Sun, Gwo-Shing; Heathcote, David; Reinsch, S.; DeSimone, Julia C.; Myers, Zachary A.

2014-01-01

The aim of our ground testing was to demonstrate the capability of safely putting specific model organisms into dehydrated stasis, and to later rehydrate and successfully grow them inside flight proven ARC EMCS seedling cassettes. The ARC EMCS seedling cassettes were originally developed to support seedling growth during space flight. The seeds are attached to a solid substrate, launched dry, and then rehydrated in a small volume of media on orbit to initiate the experiment. We hypothesized that the same seedling cassettes should be capable of acting as culture chambers for a wide range of organisms with minimal or no modification. The ability to safely preserve live organisms in a dehydrated state allows for on orbit experiments to be conducted at the best time for crew operations and more importantly provides a tightly controlled physiologically relevant growth experiment with specific environmental parameters. Thus, we performed a series of ground tests that involved growing the organisms, preparing them for dehydration on gridded Polyether Sulfone (PES) membranes, dry storage at ambient temperatures for varying periods of time, followed by rehydration. Inside the culture cassettes, the PES membranes were mounted above blotters containing dehydrated growth media. These were mounted on stainless steel bases and sealed with plastic covers that have permeable membrane covered ports for gas exchange. The results showed we were able to demonstrate acceptable normal growth of C.elegans (nematodes), E.coli (bacteria), S.cerevisiae (yeast), Polytrichum (moss) spores and protonemata, C.thalictroides (fern), D.discoideum (amoeba), and H.dujardini (tardigrades). All organisms showed acceptable growth and rehydration in both petri dishes and culture cassettes initially, and after various time lengths of dehydration. At the end of on orbit ISS European Modular Cultivation System experiments the cassettes could be frozen at ultra-low temperatures, refrigerated, or chemically preserved before being returned to Earth for analyses. Our results suggest that with protocol modifications and future verification testing we can utilize the versatile EMCS to conduct tightly controlled experiments inside our culture cassettes for a wide variety of organisms. These physiological experiments would be designed to answer questions at the molecular level about the specific stress responses of space flight.

High Speed Link Radiated Emission Reduction

NASA Astrophysics Data System (ADS)

Bisognin, P.; Pelissou, P.; Cissou, R.; Giniaux, M.; Vargas, O.

2016-05-01

To control the radiated emission of high-speed link and associated unit, the current approach is to implement overall harness shielding on cables bundles. This method is very efficient in the HF/ VHF (high frequency/ very high frequency) and UHF (ultra-high frequency) ranges when the overall harness shielding is properly bonded on EMC back-shell. Unfortunately, with the increasing frequency, the associated half wavelength matches with the size of Sub-D connector that is the case for the L band. Therefore, the unit connectors become the main source of interference emission. For the L-band and S-band, the current technology of EMC back-shell leaves thin aperture matched with the L band half wavelength and therefore, the shielding effectiveness is drastically reduced. In addition, overall harness shielding means significant increases of the harness mass.Airbus D&S Toulouse and Elancourt investigated a new solution to avoid the need of overall harness shielding. The objective is to procure EM (Electro-Magnetic) clean unit connected to cables bundles free of any overall harness shielding. The proposed solution is to implement EMC common mode filtering on signal interfaces directly on unit PCB as close as possible the unit connector.Airbus D&S Elancourt designed and manufactured eight mock-ups of LVDS (Low Voltage Differential Signaling) interface PCBs' with different solutions of filtering. After verification of the signal integrity, three mock-ups were retained (RC filter and two common mode choke coil) in addition to the reference one (without EMC filter).Airbus D&S Toulouse manufactured associated LVDS cable bundles and integrated the RX (Receiver) and TX (Transmitter) LVDS boards in shielded boxes.Then Airbus D&S performed radiated emission measurement of the LVDS links subassemblies (e.g. RX and TX boxes linked by LVDS cables) according to the standard test method. This paper presents the different tested solutions and main conclusions on the feasibility of such approach.

Enhanced methane production via repeated batch bioaugmentation pattern of enriched microbial consortia.

PubMed

Yang, Zhiman; Guo, Rongbo; Xu, Xiaohui; Wang, Lin; Dai, Meng

2016-09-01

Using batch and repeated batch cultivations, this study investigated the effects of bioaugmentation with enriched microbial consortia (named as EMC) on methane production from effluents of hydrogen-producing stage of potato slurry, as well as on the indigenous bacterial community. The results demonstrated that the improved methane production and shift of the indigenous bacterial community structure were dependent on the EMC/sludge ratio and bioaugmentation patterns. The methane yield and production rate in repeated batch bioaugmentation pattern of EMC were, respectively, average 15% and 10% higher than in one-time bioaugmentation pattern of EMC. DNA-sequencing approach showed that the enhanced methane production in the repeated batch bioaugmentation pattern of EMC mainly resulted from the enriched iron-reducing bacteria and the persistence of the introduced Syntrophomonas, which led to a rapid degradation of individual VFAs to methane. The findings contributed to understanding the correlation between the bioaugmentation of microbial consortia, community shift, and methane production. Copyright © 2016 Elsevier Ltd. All rights reserved.

55. E.M.C., photographer July 3, 1936 HUMBOLDT COUNTY, SECTION J, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

55. E.M.C., photographer July 3, 1936 HUMBOLDT COUNTY, SECTION J, HIGHWAY 1. 1-HUM-I-J #80, BITUMULS PORTION OF EXPERIMENTAL SECTION, E.M.C, 7-3-36. BACK READS: C/PROCESSING STABILIZING BITUMULS WITH BLADE AFTER BEING PROCESSED WITH SPRING TOOTH HARROW. Stamped office copy. - Redwood National & State Parks Roads, California coast from Crescent City to Trinidad, Crescent City, Del Norte County, CA

Determination of first flush criteria using dynamic EMCs (event mean concentrations) on highway stormwater runoff.

PubMed

Kim, L H; Jeong, S M; Ko, S O

2007-01-01

Recently the Ministry of Environment in Korea has developed the total maximum daily load program in accordance with the target pollutant and its concentration goal on four major large rivers. Since the program is largely related to regional development, nonpoint source control is both important and topical. Of the various nonpoint sources, highways are stormwater intensive land uses since they are impervious and have high pollutant mass emissions from vehicular activity. The event mean concentration (EMC) is useful in estimating the loadings to receiving water bodies. However, the EMC does not provide information on the time varying changes in pollutant concentration or mass emissions, which are often important for best management practice development, or understanding shock loads. Therefore, in this study a new concept, the dynamic EMC determination method, will be introduced to clearly verify the relationship between EMC and the first flush effect. Three monitoring sites in Daejeon metropolitan city areas were equipped with an automatic rainfall gauge and a flow meter for accumulating the data such as rainfall and runoff flow. The dynamic EMC method was applied to more than 17 events, and the improved first flush criteria were determined on the ranges of storm duration and accumulated rainfall.

Track propagation methods for the correlation of charged tracks with clusters in the calorimeter of the bar PANDA experiment

NASA Astrophysics Data System (ADS)

Nasawasd, T.; Simantathammakul, T.; Herold, C.; Stockmanns, T.; Ritman, J.; Kobdaj, C.

2018-02-01

To classify clusters of hits in the electromagnetic calorimeter (EMC) of bar PANDA (antiProton ANnihilation at DArmstadt), one has to match these EMC clusters with tracks of charged particles reconstructed from hits in the tracking system. Therefore the tracks are propagated to the surface of the EMC and associated with EMC clusters which are nearby and below a cut parameter. In this work, we propose a helix propagator to extrapolate the track from the Straw Tube Tracker (STT) to the inner surface of the EMC instead of the GEANE propagator which is already embedded within the PandaRoot computational framework. The results for both propagation methods show a similar quality, with a 30% gain in CPU time when using the helix propagator. We use Monte-Carlo truth information to compare the particle ID of the EMC clusters with the ID of the extrapolated points, thus deciding upon the correctness of the matches. By varying the cut parameter as a function of transverse momentum and particle type, our simulations show that the purity can be increased by 3-5% compared to the default value which is a constant cut in the bar PANDA simulation framework PandaRoot.

The Electromagnetic Compatibility (EMC) Design Challenge for Scientific Spacecraft Powered by a Stirling Power Converter

NASA Technical Reports Server (NTRS)

Sargent, Noel B.

2001-01-01

A 55 We free-piston Stirling Technology Demonstration Convertor (TDC) has been tested as part of an evaluation to determine its feasibility as a means for significantly reducing the amount of radioactive material required compared to Radioisotope Thermoelectric Generators (RTGs) to support long-term space science missions. Measurements were made to quantify the low frequency magnetic and electric fields radiated from the Stirling's 80 Hertz (Hz) linear alternator and control electronics in order to determine the magnitude of reduction that will be required to protect sensitive field sensors aboard some science missions. One identified "Solar Probe" mission requires a 100 dB reduction in the low frequency magnetic field over typical military standard design limits, to protect its plasma wave sensor. This paper discusses the electromagnetic interference (EMI) control options relative to the physical design impacts for this power system, composed of 3 basic electrical elements. They are (1) the Stirling Power Convertor with its linear alternator, (2) the power switching and control electronics to convert the 90 V, 80 Hz alternator output to DC for the use of the spacecraft, and (3) the interconnecting wiring including any instrumentation to monitor and control items 1 and 2.

Are prediction models for Lynch syndrome valid for probands with endometrial cancer?

PubMed

Backes, Floor J; Hampel, Heather; Backes, Katherine A; Vaccarello, Luis; Lewandowski, George; Bell, Jeffrey A; Reid, Gary C; Copeland, Larry J; Fowler, Jeffrey M; Cohn, David E

2009-01-01

Currently, three prediction models are used to predict a patient's risk of having Lynch syndrome (LS). These models have been validated in probands with colorectal cancer (CRC), but not in probands presenting with endometrial cancer (EMC). Thus, the aim was to determine the performance of these prediction models in women with LS presenting with EMC. Probands with EMC and LS were identified. Personal and family history was entered into three prediction models, PREMM(1,2), MMRpro, and MMRpredict. Probabilities of mutations in the mismatch repair genes were recorded. Accurate prediction was defined as a model predicting at least a 5% chance of a proband carrying a mutation. From 562 patients prospectively enrolled in a clinical trial of patients with EMC, 13 (2.2%) were shown to have LS. Nine patients had a mutation in MSH6, three in MSH2, and one in MLH1. MMRpro predicted that 3 of 9 patients with an MSH6, 3 of 3 with an MSH2, and 1 of 1 patient with an MLH1 mutation could have LS. For MMRpredict, EMC coded as "proximal CRC" predicted 5 of 5, and as "distal CRC" three of five. PREMM(1,2) predicted that 4 of 4 with an MLH1 or MSH2 could have LS. Prediction of LS in probands presenting with EMC using current models for probands with CRC works reasonably well. Further studies are needed to develop models that include questions specific to patients with EMC with a greater age range, as well as placing increased emphasis on prediction of LS in probands with MSH6 mutations.

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > NOAH > IMPLEMENTATION SCHEDULLE Home Operational Products Experimental Data Verification Model Configuration Implementation Schedule Collaborators Documentation FAQ Code

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > GEFS > IMPLEMENTATION SCHEDULLE Home Operational Products Experimental Data Verification Model Configuration Implementation Schedule Collaborators Documentation FAQ Code

Penetration of High Intensity Radiated Fields (HIRF) Into General Aviation Aircraft

NASA Technical Reports Server (NTRS)

Balanis, Constantine A.; Birtcher, Craig R.; Georgakopoulos, Stavros V.; Panaretos, Anastasios H.

2004-01-01

The ability to design and achieve electromagnetic compatibility is becoming more challenging with the rapid development of new electronic products and technologies. The importance of electromagnetic interference (EMI) and electromagnetic compatibility (EMC) issues stems from the fact that the ambient electromagnetic environment has become very hostile; that is, it increases both in density and intensity, while the current trend in technology suggests the number of electronic devices increases in homes, businesses, factories, and transportation vehicles. Furthermore, the operating frequency of products coming into the market continuously increases. While cell phone technology has exceeded 1 GHz and Bluetooth operates at 2.4 GHz, products involving satellite communications operate near 10 GHz and automobile radar systems involve frequencies above 40 GHz. The concern about higher frequencies is that they correspond to smaller wavelengths, therefore electromagnetic waves are able to penetrate equipment enclosure through apertures or even small cracks more easily. In addition, electronic circuits have become small in size, and they are usually placed on motherboards or housed in boxes in very close proximity. Cosite interference and coupling in all electrical and electronic circuit assemblies are two essential issues that have to be examined in every design.

Genomic Characterization of a Newly Discovered Coronavirus Associated with Acute Respiratory Distress Syndrome in Humans

PubMed Central

van Boheemen, Sander; de Graaf, Miranda; Lauber, Chris; Bestebroer, Theo M.; Raj, V. Stalin; Zaki, Ali Moh; Osterhaus, Albert D. M. E.; Haagmans, Bart L.; Gorbalenya, Alexander E.; Snijder, Eric J.; Fouchier, Ron A. M.

2012-01-01

ABSTRACT A novel human coronavirus (HCoV-EMC/2012) was isolated from a man with acute pneumonia and renal failure in June 2012. This report describes the complete genome sequence, genome organization, and expression strategy of HCoV-EMC/2012 and its relation with known coronaviruses. The genome contains 30,119 nucleotides and contains at least 10 predicted open reading frames, 9 of which are predicted to be expressed from a nested set of seven subgenomic mRNAs. Phylogenetic analysis of the replicase gene of coronaviruses with completely sequenced genomes showed that HCoV-EMC/2012 is most closely related to Tylonycteris bat coronavirus HKU4 (BtCoV-HKU4) and Pipistrellus bat coronavirus HKU5 (BtCoV-HKU5), which prototype two species in lineage C of the genus Betacoronavirus. In accordance with the guidelines of the International Committee on Taxonomy of Viruses, and in view of the 75% and 77% amino acid sequence identity in 7 conserved replicase domains with BtCoV-HKU4 and BtCoV-HKU5, respectively, we propose that HCoV-EMC/2012 prototypes a novel species in the genus Betacoronavirus. HCoV-EMC/2012 may be most closely related to a coronavirus detected in Pipistrellus pipistrellus in The Netherlands, but because only a short sequence from the most conserved part of the RNA-dependent RNA polymerase-encoding region of the genome was reported for this bat virus, its genetic distance from HCoV-EMC remains uncertain. HCoV-EMC/2012 is the sixth coronavirus known to infect humans and the first human virus within betacoronavirus lineage C. PMID:23170002

Status of Emergency Contraceptives in Europe One Year after the European Medicines Agency's Recommendation to Switch Ulipristal Acetate to Non-Prescription Status.

PubMed

Italia, Salvatore; Brand, Helmut

2016-01-01

In November 2014, the European Medicines Agency (EMA) recommended switching the emergency contraceptive (EMC) ulipristal acetate to non-prescription status. This study's objective is to assess the current legal status of the two EMCs ulipristal acetate and levonorgestrel in Europe and to report on the development of sales figures for EMCs since they were made freely available. Health authorities were contacted in autumn 2015 and asked about the current status of EMCs and whether the sales figures had changed after a switch to non-prescription status. Additionally, data on consumption were collected in 18 German community pharmacies. As of November 2015, most countries in the European Union (EU) have followed the EMA recommendation. Hungary kept the prescription-only status. In Malta, EMC drugs are not authorized. Germany and Croatia switched levonorgestrel to non-prescription status as well. Of the EU candidate and European Free Trade Association countries, ulipristal acetate is available without prescription in Norway and Bosnia and Herzegovina only. Several countries reported an increase in EMC sales since the switch. An EMA recommendation can strongly contribute to the harmonization of a drug's legal status in the EU. In most European countries, ulipristal acetate and/or levonorgestrel are now freely available. © 2016 The Author(s) Published by S. Karger AG, Basel.

Ester-Based Electrolytes for Low-Temperature Li-Ion Cells

NASA Technical Reports Server (NTRS)

Smart, Marshall; Bugga, Ratnakumar

2005-01-01

Electrolytes comprising LiPF6 dissolved at a concentration of 1.0 M in five different solvent mixtures of alkyl carbonates have been found to afford improved performance in rechargeable lithium-ion electrochemical cells at temperatures as low as -70 C. These and other electrolytes have been investigated in continuing research directed toward extending the lower limit of practical operating temperatures of Li-ion cells. This research at earlier stages, and the underlying physical and chemical principles, were reported in numerous previous NASA Tech Briefs articles, the most recent being Low-EC-Content Electrolytes for Low-Temperature Li-Ion Cells (NPO-30226), NASA Tech Briefs, Vol. 27, No. 1 (January 2003), page 46. The ingredients of the present solvent mixtures are ethylene carbonate (EC), ethyl methyl carbonate (EMC), methyl butyrate (MB), methyl propionate (MP), ethyl propionate (EP), ethyl butyrate (EB), and ethyl valerate (EV). In terms of volume proportions of these ingredients, the present solvent mixtures are 1EC + 1EMC + 8MB, 1EC + 1EMC + 8EB, 1EC + 1EMC + 8MP, 1EC + 1EMC + 8EV, and 1EC + 9EMC. These electrolytes were placed in Liion cells containing carbon anodes and LiNi0.8Co0.2O2 cathodes, and the low-temperature electrical performances of the cells were measured. The cells containing the MB and MP mixtures performed best.

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > NOAH > PEOPLE Home Operational Products Experimental Data Verification / Development Contacts Change Log Events Calendar Events People Numerical Forecast Systems Coming Soon. NOAA

Sorption Isotherm of Southern Yellow Pine-High Density Polyethylene Composites.

PubMed

Liu, Feihong; Han, Guangping; Cheng, Wanli; Wu, Qinglin

2015-01-20

Temperature and relative humidity (RH) are two major external factors, which affect equilibrium moisture content (EMC) of wood-plastic composites (WPCs). In this study, the effect of different durability treatments on sorption and desorption isotherms of southern yellow pine (SYP)-high density polyethylene (HDPE) composites was investigated. All samples were equilibriumed at 20 °C and various RHs including 16%, 33%, 45%, 66%, 75%, 85%, 93%, and100%. EMCs obtained from desorption and absorption for different WPC samples were compared with Nelson's sorption isotherm model predictions using the same temperature and humidity conditions. The results indicated that the amount of moisture absorbed increased with the increases in RH at 20 °C. All samples showed sorption hysteresis at a fixed RH. Small difference between EMC data of WPC samples containing different amount of ultraviolet (UV) stabilizers were observed. Similar results were observed among the samples containing different amount of zinc borate (ZB). The experimental data of EMCs at various RHs fit to the Nelson's sorption isotherm model well. The Nelson's model can be used to predicate EMCs of WPCs under different RH environmental conditions.

Sorption Isotherm of Southern Yellow Pine—High Density Polyethylene Composites

PubMed Central

Liu, Feihong; Han, Guangping; Cheng, Wanli; Wu, Qinglin

2015-01-01

Temperature and relative humidity (RH) are two major external factors, which affect equilibrium moisture content (EMC) of wood-plastic composites (WPCs). In this study, the effect of different durability treatments on sorption and desorption isotherms of southern yellow pine (SYP)-high density polyethylene (HDPE) composites was investigated. All samples were equilibriumed at 20 °C and various RHs including 16%, 33%, 45%, 66%, 75%, 85%, 93%, and100%. EMCs obtained from desorption and absorption for different WPC samples were compared with Nelson’s sorption isotherm model predictions using the same temperature and humidity conditions. The results indicated that the amount of moisture absorbed increased with the increases in RH at 20 °C. All samples showed sorption hysteresis at a fixed RH. Small difference between EMC data of WPC samples containing different amount of ultraviolet (UV) stabilizers were observed. Similar results were observed among the samples containing different amount of zinc borate (ZB). The experimental data of EMCs at various RHs fit to the Nelson’s sorption isotherm model well. The Nelson’s model can be used to predicate EMCs of WPCs under different RH environmental conditions. PMID:28787943

Active System for Electromagnetic Perturbation Monitoring in Vehicles

NASA Astrophysics Data System (ADS)

Matoi, Adrian Marian; Helerea, Elena

Nowadays electromagnetic environment is rapidly expanding in frequency domain and wireless services extend in terms of covered area. European electromagnetic compatibility regulations refer to limit values regarding emissions, as well as procedures for determining susceptibility of the vehicle. Approval procedure for a series of cars is based on determining emissions/immunity level for a few vehicles picked randomly from the entire series, supposing that entire vehicle series is compliant. During immunity assessment, the vehicle is not subjected to real perturbation sources, but exposed to electric/magnetic fields generated by laboratory equipment. Since current approach takes into account only partially real situation regarding perturbation sources, this paper proposes an active system for determining electromagnetic parameters of vehicle's environment, that implements a logical diagram for measurement, satisfying the imposed requirements. This new and original solution is useful for EMC assessment of hybrid and electrical vehicles.

Automating the deconfliction of jamming and spectrum management

NASA Astrophysics Data System (ADS)

Segner, Samuel M.

1988-12-01

Powerful airborne and ground based jammers are being fielded by all services and nations as part of their intelligence/electronic warfare (I/EW) combat capability. For their survivability, these I/EW systems operate far from the FLOT; this creates rather large denial areas to friendly forces when they jam. Manual coordination between IE/W managers and spectrum managers is not practical to take on targets of opportunities or track the intended enemy victims when these victims counter by frequency maneuvers. Two possible architectures, one centralized, the other decentralized, are explored as is the applicability of the electromagnetic compatibility (EMC) software developed for the U.S. Army Automatic Tactical Frequency Engineering System (ATFES) pilot program. The proposed approach is to apply the principles of the Joint Commanders EW Staff (JCEWS). The initial simplified software to demonstrate the computer aided coordination at VHF is explained.

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > RAP, HRRR > Home Operational Products Experimental Data Verification Model Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post

Relationship between fumonisin contamination of feed and mystery swine disease. A case-control study.

PubMed

Bane, D P; Neumann, E J; Hall, W F; Harlin, K S; Slife, R L

1992-02-01

Fumonisin is a recently identified mycotoxin that has been shown to be the cause of pulmonary edema disease in swine and leukoencephalomalacia in horses. Mystery Swine Disease (MSD), is an economically devastating disease complex of unknown etiology that has been reported to have occurred in several swine producing states since 1988. To determine the relationship between MSD and fumonisin, a case-control study was carried out in Illinois in mid-1990. Feed samples collected from 12 case and 9 control farms were analyzed for fumonisin. Sera from swine on all farms was screened for titers against encephalomyocarditis (EMC) virus and concentrations of alpha-1 acid glycoprotein (an acute phase reactive protein). Fumonisin concentrations greater than or equal to 20 ppm were found on 1 control farm (1/9) and 8 case farms (8/12). Titers against EMC virus (greater than or equal to 1:16) were found on 5 control farms (5/9) and on 6 case farms (6/12). Farms with greater than or equal to 20 ppm fumonisin in the feed were at significantly increased risk (OR = 11.2, Fisher's exact test p = 0.037) for MSD. Furthermore, the pi2 test for trend was (p = 0.017), meaning that as the level of fumonisin in the feed increased, the risk of MSD also increased. The presence of EMC virus titers in the sow herd was not a significant risk for MSD (OR = 1.25, Fisher's exact test p = 0.75). Alpha-1 acid glycoprotein concentrations obtained from a 2-week old nursing pigs differed significantly (p = 0.0005) between MSD case and control herds.

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > NOAH > HOME Home Operational Products Experimental Data Verification Model PAGE LOGO NCEP HOME NWS LOGO NOAA HOME NOAA HOME Disclaimer for this non-operational web page

Personalized objects can optimize the diagnosis of EMCS in the assessment of functional object use in the CRS-R: a double blind, randomized clinical trial.

PubMed

Sun, Yuxiao; Wang, Jianan; Heine, Lizette; Huang, Wangshan; Wang, Jing; Hu, Nantu; Hu, Xiaohua; Fang, Xiaohui; Huang, Supeng; Laureys, Steven; Di, Haibo

2018-04-12

Behavioral assessment has been acted as the gold standard for the diagnosis of disorders of consciousness (DOC) patients. The item "Functional Object Use" in the motor function sub-scale in the Coma Recovery Scale-Revised (CRS-R) is a key item in differentiating between minimally conscious state (MCS) and emergence from MCS (EMCS). However, previous studies suggested that certain specific stimuli, especially something self-relevant can affect DOC patients' scores of behavioral assessment scale. So, we attempted to find out if personalized objects can improve the diagnosis of EMCS in the assessment of Functional Object Use by comparing the use of patients' favorite objects and other common objects in MCS patients. Twenty-one post-comatose patients diagnosed as MCS were prospectively included. The item "Functional Object Use" was assessed by using personalized objects (e.g., cigarette, paper) and non-personalized objects, which were presented in a random order. The rest assessments were performed following the standard protocol of the CRS-R. The differences between functional uses of the two types of objects were analyzed by the McNemar test. The incidence of Functional Object Use was significantly higher using personalized objects than non-personalized objects in the CRS-R. Five out of the 21 MCS studied patients, who were assessed with non-personalized objects, were re-diagnosed as EMCS with personalized objects (χ 2  = 5, df = 1, p < 0.05). Personalized objects employed here seem to be more effective to elicit patients' responses as compared to non-personalized objects during the assessment of Functional Object Use in DOC patients. Clinical Trials.gov: NCT02988206 ; Date of registration: 2016/12/12.

[A rare tumor of the parapharyngeal space: myxoid chondrosarcoma].

PubMed

Bahri, I; Boudawara, T; Sellami, A; Khabir, A; Ghorgel, M; Drira, M; Daoud, J; Jlidi, R

2002-01-01

Extrasqueletal myxoid chondrosarcoma (EMC) is an uncommon soft tissue malignant tumor, locally aggressive with a high incidence of distant metastasis. It has distinctive clinical, immunophenotypic, cytogenetic and ultrastructural features. Most EMC are associated with the translocation t(9;22) (q22;q12). Their occurrence in the parapharyngeal space is extremely rare. Our objective is to discuss the difficulties of the histological diagnosis of EMC and to describe its immunophenotypic, cytogenetic features and clinical behavior. We report a case of a 67 years old woman who presented with a five months history of dysphagia. The oral examination found a mass displacing the posterior and left walls of the pharynx. Surgical resection of the tumor was undertaken. The pathologic examination concluded to the diagnosis of an EMC of the left parapharygeal space. Now, the patient is receiving an adjuvant radiotherapy.

Increased levels of inflammatory cytokines in the female reproductive tract are associated with altered expression of proteases, mucosal barrier proteins, and an influx of HIV-susceptible target cells.

PubMed

Arnold, Kelly B; Burgener, Adam; Birse, Kenzie; Romas, Laura; Dunphy, Laura J; Shahabi, Kamnoosh; Abou, Max; Westmacott, Garrett R; McCorrister, Stuart; Kwatampora, Jessie; Nyanga, Billy; Kimani, Joshua; Masson, Lindi; Liebenberg, Lenine J; Abdool Karim, Salim S; Passmore, Jo-Ann S; Lauffenburger, Douglas A; Kaul, Rupert; McKinnon, Lyle R

2016-01-01

Elevated inflammatory cytokines (EMCs) at mucosal surfaces have been associated with HIV susceptibility, but the underlying mechanisms remain unclear. We characterized the soluble mucosal proteome associated with elevated cytokine expression in the female reproductive tract. A scoring system was devised based on the elevation (upper quartile) of at least three of seven inflammatory cytokines in cervicovaginal lavage. Using this score, HIV-uninfected Kenyan women were classified as either having EMC (n=28) or not (n=68). Of 455 proteins quantified in proteomic analyses, 53 were associated with EMC (5% false discovery rate threshold). EMCs were associated with proteases, cell motility, and actin cytoskeletal pathways, whereas protease inhibitor, epidermal cell differentiation, and cornified envelope pathways were decreased. Multivariate analysis identified an optimal signature of 16 proteins that distinguished the EMC group with 88% accuracy. Three proteins in this signature were neutrophil-associated proteases that correlated with many cytokines, especially GM-CSF (granulocyte-macrophage colony-stimulating factor), IL-1β (interleukin-1β), MIP-3α (macrophage inflammatory protein-3α), IL-17, and IL-8. Gene set enrichment analyses implicated activated immune cells; we verified experimentally that EMC women had an increased frequency of endocervical CD4(+) T cells. These data reveal strong linkages between mucosal cytokines, barrier function, proteases, and immune cell movement, and propose these as potential mechanisms that increase risk of HIV acquisition.

40 CFR 63.6675 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

..., and Process Heaters Using Portable Analyzers”, EMC Conditional Test Protocol 30 (CTM-30), Gas Research... emergency situation. Examples include stationary RICE used to produce power for critical networks or... institutional establishments such as medical centers, nursing homes, research centers, institutions of higher...

40 CFR 63.6675 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

..., and Process Heaters Using Portable Analyzers”, EMC Conditional Test Protocol 30 (CTM-30), Gas Research... emergency situation. Examples include stationary RICE used to produce power for critical networks or... institutional establishments such as medical centers, nursing homes, research centers, institutions of higher...

National Centers for Environmental Prediction

Science.gov Websites

different sites - Examples of the testing on different sites - Computing Environment NCEPLIBS Documentation - Procedures and conventions for NCEPLIBS use - Tutorials of NCEPLIBS use. Examples - Applications and ) 5830 University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page generated:Sunday

Testing of Unmanned Ground Vehicle (UGV) Systems

DTIC Science & Technology

2009-02-12

Emissions - Intra-system EMC TOP 1-2-51253 TOP 1-2-51154 TOP 2-2-61355 Determines whether the item tested meets the electromagnetic radiation ...effects, static electricity, and lightning criteria and the maximum electromagnetic radiation environment to which the test item may be exposed...Form 298 (Rev. 8-98) Prescribed by ANSI Std. Z39-18 2-2-540 Testing of Unmanned Ground Vehicle (UGV) Systems 5c. PROGRAM ELEMENT NUMBER 5d

Diffusional Motion of Redox Centers in Carbonate Electrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Kee Sung; Rajput, Nav Nidhi; Wei, Xiaoliang

2014-09-14

Ferrocene (Fc) and N-(ferrocenylmethyl)-N,N-dimethyl-N-ethylammonium bistrifluoromethyl-sulfonimide (Fc1N112-TFSI) were dissolved in carbonate solvents and self diffusion coefficents (D) of solutes and solvents were measured by 1H and 19F pulsed field gradient (PFG) nuclear magnetic resonance (NMR) spectroscopy. The organic solvents were propylene carbonate (PC), ethyl methyl carbonate (EMC) and a ternary mixture that also includes ethylene carbonate (EC). Results from NMR studies over the temperature range of 0-50 °C and for various concentrations (0.25 - 1.7 M) of Fc1N112-TFSI are compared to values of D simulated with classical molecular dynamics (MD). The measured self-diffusion coefficients gradually decreased as the Fc1N112-TFSI concentration increasedmore » in all solvents. Since the peaks for the two ions (Fc1N212 and TFSI) are separated in one-dimensional NMR spectra, separate diffusion coefficients could be measured and DTFSI is larger than DFc1N112 in all samples measured. The EC, PC and EMC have the same D in the neat solvent mixture and when Fc is dissolved in EC/PC/EMC at a concentration of 0.2 M, probably due to the interactions between common carbonyl structures within EC, PC and EMC. A difference in D (DPC < DEC < DEMC), and both a higher Ea for translational motion and higher effective viscosity for PC in the mixture containing Fc1N112-TFSI reflect the interaction between PC and Fc1N112+, which is a relatively stronger interaction than that between Fc1N112+ and other solvent species. In the EC/PC/EMC solution that is saturated with Fc1N112-TFSI, we find that DPC = DEC = DEMC and Fc1N112+ and all components of the EC/PC/EMC solution have the same Ea for translational motion, while the ratio DEC/PC/EMC/DFc1N112+ is approximately 3. These results reflect the lack of available free volume for independent diffusion in the saturated solution. The Fc1N112+ transference numbers lie around 0.4 and increases slightly as the temperature is increased in the PC and EMC solvents. The trends observed for D from simulations are in good agreement with experimental results and provide molecular level understanding of the solvation structure of Fc1N112-TFSI dissolved in EC/PC/EMC.« less

Estimation of limit strains in disk-type flywheels made of a compliant elastomeric matrix composite undergoing radial creep

NASA Astrophysics Data System (ADS)

Portnov, G. G.; Bakis, Ch. E.

2000-01-01

Fiber reinforced elastomeric matrix composites (EMCs) offer several potential advantages for construction of rotors for flywheel energy storage systems. One potential advantage, for safety considerations, is the existence of maximum stresses near the outside radius of thick circumferentially wound EMC disks, which could lead to a desirable self-arresting failure mode at ultimate speeds. Certain unidirectionally reinforced EMCs, however, have been noted to creep readily under the influence of stress transverse to the fibers. In this paper, stress redistribution in a spinning thick disk made of a circumferentially filament wound EMC material on a small rigid hub has been analyzed with the assumption of total radial stress relaxation due to radial creep. It is shown that, following complete relaxation, the circumferential strains and stresses are maximized at the outside radius of the disk. Importantly, the radial tensile strains are three times greater than the circumferential strains at any given radius. Therefore, a unidirectional EMC material system that can safely endure transverse tensile creep strains of at least three times the elastic longitudinal strain capacity of the same material is likely to maintain the theoretically safe failure mode despite complete radial stress relaxation.

Energy Monitoring and Control Systems--Performance Verification and Endurance Test Procedures.

DTIC Science & Technology

1982-12-01

EM-; tK2 s) trave h.en loadted in qvstem sit ~rp sm:l , o,1 ti-’.~ -1 rouiitthe factoz’, lest. E.VEF.NT Comnmwid the system to display the status of...contractor correction of all outstanding deficiencies . 163 TEST NO: END-i Page I of 1 OBJECTIVE: To demonstrate EMCS normal mode operation 24 TITLE: Endurance

The magnitude of variability produced by methods used to estimate annual stormwater contaminant loads for highly urbanised catchments.

PubMed

Beck, H J; Birch, G F

2013-06-01

Stormwater contaminant loading estimates using event mean concentration (EMC), rainfall/runoff relationship calculations and computer modelling (Model of Urban Stormwater Infrastructure Conceptualisation--MUSIC) demonstrated high variability in common methods of water quality assessment. Predictions of metal, nutrient and total suspended solid loadings for three highly urbanised catchments in Sydney estuary, Australia, varied greatly within and amongst methods tested. EMC and rainfall/runoff relationship calculations produced similar estimates (within 1 SD) in a statistically significant number of trials; however, considerable variability within estimates (∼50 and ∼25 % relative standard deviation, respectively) questions the reliability of these methods. Likewise, upper and lower default inputs in a commonly used loading model (MUSIC) produced an extensive range of loading estimates (3.8-8.3 times above and 2.6-4.1 times below typical default inputs, respectively). Default and calibrated MUSIC simulations produced loading estimates that agreed with EMC and rainfall/runoff calculations in some trials (4-10 from 18); however, they were not frequent enough to statistically infer that these methods produced the same results. Great variance within and amongst mean annual loads estimated by common methods of water quality assessment has important ramifications for water quality managers requiring accurate estimates of the quantities and nature of contaminants requiring treatment.

Hydration behaviour of food grains and modelling their moisture pick up as per Peleg's equation: Part I. Cereals.

PubMed

Vasudeva, Singh; Vishwanathan, K H; Aswathanarayana, K N; Indhudhara Swamy, Y M

2010-01-01

Cereals and millets generally hydrate at a moderate rate and their hydration behaviour differs in native and in processed state. The study was on the hydration of paddy, milled rice, parboiled rice, wheat, millets and equilibrium moisture content (EMC) on soaking at room temperature. Paddy hydrated very slowly, hydration rate was slow in brown rice but fast in milled rice and highest in waxy rice. In most of the rice varieties, maximum absorption occurred at the end of 30 min. In wheat hydration rate was slow and its EMC was highest (43%). Maize grits of big size hydrated slowly compared to small grits. In coarse cereals EMC varied from 28 to 38%. Foxtail millet hydration was slow whereas that of finger millet was fast. The data were tested on the Peleg's equation, which gave a reasonable fit to experimental data. Peleg's constants k1 and k2 were calculated for the above grains and their hydration behaviour has been predicted. The model fitted very well to milled rice hydration data where the coefficient of variance ranged from 0.9982 to 0.9995. With exception in some millet the hydration data fitted well with the Peleg's equation. Generalized equations have been formulated for prediction of moisture content of cereals and millets.

Characterization of silica particles modified with γ-methacryloxypropyltrimethoxysilane

NASA Astrophysics Data System (ADS)

Jiang, Jun; Wang, Wang; Shen, Haiying; Wang, Jiamin; Cao, Jinzhen

2017-03-01

The surface of hydrophilic silica particles was modified with different concentrations (2, 4, 6, 8 and 10%) of γ-methacryloxypropyltrimethoxysilane (MPTS). The hydrophobicity and hygroscopicity of unmodified and modified silica were investigated through water contact angle (WCA) tests and dynamic vapor sorption (DVS) method, respectively. The results showed that the surface properties of silica were closely related with the MPTS concentration. Within the range of MPTS concentration applied, 8% MPTS modified silica showed the least aggregation. With the increasing MPTS concentration, the WCAs on modified silica film increased correspondingly, and finally exceeded 90° at 6% and 8% concentrations. The equilibrium moisture contents (EMCs) of modified silica also decreased with the increasing MPTS concentration. The improvement on hydrophobicity can be correlated with the reduction of residual hydroxyl groups (-OH) on modified silica. The self-condensation of MPTS began to occur at concentrations higher than 4%, especially at 8%. Owing to this effect, the modified silica with 8% MPTS showed a slightly higher EMC than 6% MPTS within low relative humidity (RH) range up to 40%. At a higher RH ranging from 40 to 90%, 8% group showed the lowest EMCs because of its highest hydrophobicity and low specific surface area. A mechanism concerning the MPTS modification of silica was also proposed in this study based on the research results.

Water quality of an urban wet detention pond in Madison, Wisconsin, 1987-88

USGS Publications Warehouse

House, L.B.; Waschbusch, R.J.; Hughes, P.E.

1993-01-01

A 5,670-sq m wet detention pond was monitored by the U.S. Geological Survey to determine its effect on the water quality of urban runoff. The pond has a drainage area of 0.96-sq km, composed primarily of single-family residential land use. Event-mean concentrations (EMC) were determined from samples collected for sediment, nutrients, and selected metals at the pond's inflow and outflow sites. EMC samples were collected for 64 runoff events during the study period from February 1987 to April 1988. Storm precipitation ranged from 1 to 51 mm during these events. Inflow and outflow EMC and constituent loads were compared to determine the trap efficiency of the pond. Trap efficiency varied considerably among water-quality constituents. In general, the detention pond decreased the EMC of sampled constituents at the outlet compared to the inlet. The median decrease in EMC for suspended solids was 88 percent, 60 percent for total chemical oxygen demand (COD), 43 percent for total phosphorus, 38 percent for total Kjeldahl nitrogen, 65 percent for total nitrite plus nitrate, and 71 percent for total lead. A notable exception to the general decrease in EMC is for chloride. The EMC for chloride was generally higher in outflow from the pond than in the inflow. This is attributed to an unmonitored influx of chloride to the pond during the winter that subsequently was flushed out during monitored runoff events. The total study-period loads of most constituents were less leaving the pond than the loads entering it. This decrease is attributed to the constituents transported on suspended sediment being deposited in the pond. The decrease in total load of suspended solids was 88 percent, 62 percent for total COD, 58 percent for total phosphorus, 46 percent for total Kjeldahl nitrogen, 62 percent for total nitrite plus nitrate, 97 percent for total copper, and 93 percent for total lead. (USGS)

--No Title--

Science.gov Websites

2008073000 2008072900 2008072800 Background information bias reduction = ( | domain-averaged ensemble mean bias | - | domain-averaged bias-corrected ensemble mean bias | / | domain-averaged bias-corrected ensemble mean bias | NAEFS Products | NAEFS | EMC Ensemble Products EMC | NCEP | National Weather Service

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > NAM > EXPERIMENTAL DATA Home NAM Operational Products HIRESW Operational Products Operational Forecast Graphics Experimental Forecast Graphics Verification and Diagnostics Model PARALLEL/EXPERIMENTAL MODEL FORECAST GRAPHICS OPERATIONAL VERIFICATION / DIAGNOSTICS PARALLEL VERIFICATION

Primary extraskeletal myxoid chondrosarcoma in cerebellum: A case report with literature review.

PubMed

Qin, You; Zhang, Hai-Bo; Ke, Chang-Shu; Huang, Jing; Wu, Bian; Wan, Chao; Yang, Chen-Su; Yang, Kun-Yu

2017-11-01

Extraskeletal myxoid chondrosarcoma (EMC) is a rare malignant neoplasm of which intracranial EMC is the rarest. We present an unusual case report of a 41-year-old woman who was sent to the emergency department for a sudden headache and other symptoms related to increased intracranial pressure. Emergent CT revealed an occupying lesion in the left cerebellum with surrounding edema. A complete surgical excision of the lesion through a transcortical approach was performed. After the operation, this patient received adjuvant radiotherapy and temozolomide treatment. Pathology diagnosis was an intracranial EMC. The patient survives with no tumor recurrence as of the last follow-up. Progression-free survival exceeded 20 months. We have reviewed the literature and here summarize the diagnosis and treatment options for intracranial EMC. Diagnosis and treatment options of this rare disease are discussed. Copyright © 2017 The Authors. Published by Wolters Kluwer Health, Inc. All rights reserved.

[Study on the characteristics of combined sewer overflow from the high density residential area in Shanghai].

PubMed

Li, He; Li, Tian

2006-08-01

The urban non-point pollution has become main pollution resource of urban water bodies of Shanghai. Character of combined sewer overflow from watershed SA in Shanghai was studied, and the correlation of influence factors to the EMCs of overflows was discussed. It is found that the EMCs of COD, BOD, SS, NH3-N, TN, TP are 614 mg/L, 208.5 mg/L, 684 mg/L, 17.6 mg/L, 29.8 mg/L, 3.0 mg/L respectively, and the values obtained herein are much higher than the documented data from other countries. From the probability plot of the EMCs, it is found that the BOD has the best fitness for lognormal distribution; and correlation between the EMCs of COD, SS and the ratio of antecedent dry weather time to rain duration is quite good.

Pollutant concentrations and pollution loads in stormwater runoff from different land uses in Chongqing.

PubMed

Wang, Shumin; He, Qiang; Ai, Hainan; Wang, Zhentao; Zhang, Qianqian

2013-03-01

To investigate the distribution of pollutant concentrations and pollution loads in stormwater runoff in Chongqing, six typical land use types were selected and studied from August 2009 to September 2011. Statistical analysis on the distribution of pollutant concentrations in all water samples shows that pollutant concentrations fluctuate greatly in rainfall-runoff, and the concentrations of the same pollutant also vary greatly in different rainfall events. In addition, it indicates that the event mean concentrations (EMCs) of total suspended solids (TSS) and chemical oxygen demand (COD) from urban traffic roads (UTR) are significantly higher than those from residential roads (RR), commercial areas (CA), concrete roofs (CR), tile roofs (TRoof), and campus catchment areas (CCA); and the EMCs of total phosphorus (TP) and NH3-N from UTR and CA are 2.35-5 and 3 times of the class-II standard values specified in the Environmental Quality Standards for Surface Water (GB 3838-2002). The EMCs of Fe, Pb and Cd are also much higher than the class-III standard values. The analysis of pollution load producing coefficients (PLPC) reveals that the main pollution source of TSS, COD and TP is UTR. The analysis of correlations between rainfall factors and EMCs/PLPC indicates that rainfall duration is correlated with EMCs/PLPC of TSS for TRoof and TP for UTR, while rainfall intensity is correlated with EMCs/PLPC of TP for both CR and CCA. The results of this study provide a reference for better management of non-point source pollution in urban regions.

EMC HWRF Weekly Meeting Homepage

Science.gov Websites

structure using idealized HWRF simulations with GFS and MYJ PBL schemes by Jun Zhang (HRD/AOML) NOAA- MoES Zhan Zhang(EMC) (NOTE: Links open presentations in a new window) Please e-mail comments, questions, or

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > Mesoscale Modeling > PEOPLE Home Mission Models R & D Collaborators Documentation Change Log People Calendar References Verification/Diagnostics Tropical & Extratropical Cyclone Tracks & Verification Implementation Info FAQ Disclaimer More Info MESOSCALE MODELING PEOPLE

Adapting PC104Plus for Space

NASA Technical Reports Server (NTRS)

Abbott, Larry; Cox, Gary; Nguyen, Hai

2000-01-01

This article addresses the issues associated with adapting the commercial PC104Plus standard and its associated architecture to the requirements of space applications. In general, space applications exhibit extreme constraints on power, weight, and volume. EMI and EMC are also issues of significant concern. Additionally, space applications have to survive high radiation environment. Finally, NASA is always concerned about achieving cost effective solutions that are compatible with safety and launch constraints. Weight and volume constraints are directly related to high launch cost. Power on the other hand is not only related to the high launch costs, but are related to the problem of dissipating the resulting heat once in space. The article addresses why PC104Plus is an appropriate solution for the weight and volume issues. The article also addresses what NASA did electrically to reduce power consumption and mechanically dissipate the associated heat in a microgravity and vacuum environment, and how these solutions allow NASA to integrate various sizes of ruggedized custom PC104 boards with COTS, PC104 complaint boards for space applications. In addition to the mechanical changes to deal with thermal dissipation NASA also made changes to minimize EMI. Finally, radiation issues are addressed as well as the architectural and testing solutions and the implications for use of COTS PC104Plus boards.

Mars Surface Habitability Options

NASA Technical Reports Server (NTRS)

Howe, A. Scott; Simon, Matthew; Smitherman, David; Howard, Robert; Toups, Larry; Hoffman, Stephen J.

2015-01-01

This paper reports on current habitability concepts for an Evolvable Mars Campaign (EMC) prepared by the NASA Human Spaceflight Architecture Team (HAT). For many years NASA has investigated alternative human Mars missions, examining different mission objectives, trajectories, vehicles, and technologies; the combinations of which have been referred to as reference missions or architectures. At the highest levels, decisions regarding the timing and objectives for a human mission to Mars continue to evolve while at the lowest levels, applicable technologies continue to advance. This results in an on-going need for assessments of alternative system designs such as the habitat, a significant element in any human Mars mission scenario, to provide meaningful design sensitivity characterizations to assist decision-makers regarding timing, objectives, and technologies. As a subset of the Evolvable Mars Campaign activities, the habitability team builds upon results from past studies and recommends options for Mars surface habitability compatible with updated technologies.

Electrical Grounding Architecture for Unmanned Spacecraft

NASA Technical Reports Server (NTRS)

1998-01-01

This handbook is approved for use by NASA Headquarters and all NASA Centers and is intended to provide a common framework for consistent practices across NASA programs. This handbook was developed to describe electrical grounding design architecture options for unmanned spacecraft. This handbook is written for spacecraft system engineers, power engineers, and electromagnetic compatibility (EMC) engineers. Spacecraft grounding architecture is a system-level decision which must be established at the earliest point in spacecraft design. All other grounding design must be coordinated with and be consistent with the system-level architecture. This handbook assumes that there is no one single 'correct' design for spacecraft grounding architecture. There have been many successful satellite and spacecraft programs from NASA, using a variety of grounding architectures with different levels of complexity. However, some design principles learned over the years apply to all types of spacecraft development. This handbook summarizes those principles to help guide spacecraft grounding architecture design for NASA and others.

Information Security due to Electromagnetic Environments

NASA Astrophysics Data System (ADS)

Sekiguchi, Hidenori; Seto, Shinji

Generally, active electronic devices emit slightly unintentional electromagnetic noise. From long ago, electromagnetic emission levels have been regulated from the aspect of electromagnetic compatibility (EMC). Also, it has been known the electromagnetic emissions have been generated from the ON/OFF of signals in the device. Recently, it becomes a topic of conversation on the information security that the ON/OFF on a desired signal in the device can be reproduced or guessed by receiving the electromagnetic emission. For an example, a display image on a personal computer (PC) can be reconstructed by receiving and analyzing the electromagnetic emission. In sum, this fact makes known information leakage due to electromagnetic emission. “TEMPEST" that has been known as a code name originated in the U. S. Department of Defense is to prevent the information leakage caused by electromagnetic emissions. This paper reports the brief summary of the information security due to electromagnetic emissions from information technology equipments.

EMC: Mission Statement

Science.gov Websites

EMC: Mission Statement Mesoscale Modeling Branch Mission Statement The Mesoscale Modeling Branch , advanced numerical techniques applied to mesoscale modeling problems, parameterization of mesoscale new observing systems. The Mesoscale Modeling Branch publishes research results in various media for

National Centers for Environmental Prediction

Science.gov Websites

Organization Search Enter text Search Navigation Bar End Cap Search EMC Go Branches Global Climate and Weather / VISION | About EMC Click on a model logo to go to its home page RTOFS Global RTOFS Global RTOFS Atlantic

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > NAM > Home NAM Operational Products HIRESW Operational Products Operational Forecast Graphics Experimental Forecast Graphics Verification and Diagnostics Model Configuration Collaborators Documentation and Code FAQ Operational Change Log Parallel Experiment Change Log Contacts

Energy Management Control Systems: Tools for Energy Savings and Environmental Protection

NASA Technical Reports Server (NTRS)

Zsebik, Albin; Zala, Laszlo F.

2002-01-01

The change in the price of energy has encouraged the increase of energy efficiency. This report will discuss a tool to promote energy efficiency in intelligent buildings, energy management control systems (EMCS). In addition to the online control of energy production, supply, and consumption, the function of the EMCS is to support short- and long-term planning of the system operation as well as to collect, store, and regularly evaluate operation data. The strategies behind planning and implementing the EMCS as well as the manipulating the resulting data are discussed in this report.

Use of Additives to Improve Performance of Methyl Butyrate-Based Lithium-Ion Electrolytes

NASA Technical Reports Server (NTRS)

Smart, Marshall C.; Bugga, Ratnakumar V.

2011-01-01

This work addresses the need for robust rechargeable batteries that can operate well over a wide temperature range. To this end, a number of electrolyte formulations have been developed that incorporate the use of electrolyte additives to improve the high-temperature resilience, low-temperature power capability, and life characteristics of methyl butyrate-based electrolyte solutions. These electrolyte additives include mono-fluoroethylene carbonate (FEC), lithium oxalate, vinylene carbonate (VC), and lithium bis(oxalato)borate (LiBOB), which have been shown to result in improved high-temperature resilience of all carbonate-based electrolytes. Improved performance has been demonstrated of Li-ion cells with methyl butyrate-based electrolytes, including 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %); 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 2% FEC; 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 4% FEC; 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + lithium oxalate; 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 2% VC; and 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 0.10M LiBOB. These electrolytes have been shown to improve performance in MCMB-LiNiCoO2 and graphite-LiNi1/3Co1/3Mn1/3O2 experimental Li-ion cells. A number of LiPF6-based mixed carbonate electrolyte formulations have been developed that contain ester co-solvents, which have been optimized for operation at low temperature, while still providing reasonable performance at high temperature. For example, a number of ester co-solvents were investigated, including methyl propionate (MP), ethyl propionate (EP), methyl butyrate (MB), ethyl butyrate (EB), propyl butyrate (PB), and butyl butyrate (BB) in multi-component electrolytes of the following composition: 1.0M LiPF6 in ethylene carbonate (EC) + ethyl methyl carbonate (EMC) + X (20:60:20 v/v %) [where X = ester co-solvent]. ["Optimized Car bon ate and Ester-Based Li-Ion Electrolytes", NASA Tech Briefs, Vol. 32, No. 4 (April 2008), p. 56.] Focusing upon improved rate capability at low temperatures (i.e., 20 to 40 C), this approach was optimized further, resulting in the development of 1.20M LiPF6 in EC+EMC+MP (20:20:60 v/v %) and 1.20M LiPF6 in EC+EMC+EB (20:20:60 v/v %), which were demonstrated to operate well over a wide temperature range in MCMB-LiNiCoAlO2 and Li4Ti5O12(-)LiNiCoAlO2 prototype cells.

EMC: Verification

Science.gov Websites

, GFS, RAP, HRRR, HIRESW, SREF mean, International Global Models, HPC analysis Precipitation Skill Scores : 1995-Present NAM, GFS, NAM CONUS nest, International Models EMC Forecast Verfication Stats: NAM ) Real Time Verification of NCEP Operational Models against observations Real Time Verification of NCEP

SiRen: Leveraging Similar Regions for Efficient and Accurate Variant Calling

DTIC Science & Technology

2015-05-30

Cloudera, EMC2, Ericsson, Facebook, Guavus, HP, Huawei, Informatica , Intel, Microsoft, NetApp, Pivotal, Samsung, Schlumberger, Splunk, Virdata and VMware...EMC2, Ericsson, Facebook, Guavus, HP, Huawei, Informatica , Intel, Microsoft, NetApp, Pivotal, Samsung, Schlumberger, Splunk, Virdata and VMware

The development of optimal on-premise Electronic Message Center (EMC) lighting levels and sign lighting measurement techniques.

DOT National Transportation Integrated Search

2013-02-01

Research conducted recently for the United States Sign Council Foundation found no consensus in the research : literature or the practices of the commercial electronic message center (EMC) industry on lighting measurement : or appropriate lighting le...

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar ) of the Environmental Modeling Center (EMC) conducts a program of research and development in support Climate Prediction (NCWCP) 5830 University Research Court College Park, MD 20740 Page Author: EMC

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > GEFS > COLLABORATORS Home Operational Products Experimental Data ENSEMBLE FORECAST SYSTEM MSC NAEFS Products CPC NAEFS Experimental 8 to 14 Day Temperature Guidance CPC NAEFS Experimental 8 to 14 Day Precip Guidance NOAA / National Weather Service National Centers for

National Centers for Environmental Prediction

Science.gov Websites

Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post missed NDAS cycles since 1 Apr 1995 Log of NAM model code changes Log of NAM model test runs Problems and Prediction (NCWCP) 5830 University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page

National Centers for Environmental Prediction

Science.gov Websites

albedos (testing) Vegetation types Soil texture Images of Snow files: NAM snow page The NESDIS/IMS snow /ice images On Hua-Lu Pan's home page (EMC/NCEP) On the NCAR/RAP Weather Data Page Related soil moisture web sites NCEP/NASA NDAS CPC Soil Moisture Monitoring and Prediction NOAA / National Weather

National Centers for Environmental Prediction

Science.gov Websites

Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post / VISION | About EMC EMC > Mesoscale Modeling > Home Mission Models R & D Collaborators Cyclone Tracks & Verification Implementation Info FAQ Disclaimer More Info MESOSCALE MODELING NOAA

An Integrated Approach to Environmental Education: A Case Study

ERIC Educational Resources Information Center

du Preez, Nicolaas P.; Mohr-Swart, Maryna

2004-01-01

In 1994, the Executive Management Committee (EMC) of Technikon Pretoria took a strategic decision to develop educational programmes in environmental management and sustainable development. The EMC also decided to integrate these programmes with the development and implementation of an environmental management policy for Technikon Pretoria. This…

EMCS Modules/Intelligent Time Clock (ITC).

DTIC Science & Technology

1980-09-01

scale, smaller activities where a large EMCS would not be economically feasible, have had to look elsewhere to achieve their conservation goals. In this...DAEN- MPU . Washington DC: ERADCOM Tech Supp Dir. (DELSD-L) Ft. Monmouth, NJ: Engr District (Memphis) Library. Memphis TN: Natick (’en (Kwvoh flu

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > GEFS > OPERATIONAL PRODUCTS Home Operational Products Experimental Data Global Ensemble products posted by the GEFS model team are experimental analysis and forecast products , and you will find them listed under the "Experimental Data" section of our web site. The

Canonical Statistical Model for Maximum Expected Immission of Wire Conductor in an Aperture Enclosure

NASA Technical Reports Server (NTRS)

Bremner, Paul G.; Vazquez, Gabriel; Christiano, Daniel J.; Trout, Dawn H.

2016-01-01

Prediction of the maximum expected electromagnetic pick-up of conductors inside a realistic shielding enclosure is an important canonical problem for system-level EMC design of space craft, launch vehicles, aircraft and automobiles. This paper introduces a simple statistical power balance model for prediction of the maximum expected current in a wire conductor inside an aperture enclosure. It calculates both the statistical mean and variance of the immission from the physical design parameters of the problem. Familiar probability density functions can then be used to predict the maximum expected immission for deign purposes. The statistical power balance model requires minimal EMC design information and solves orders of magnitude faster than existing numerical models, making it ultimately viable for scaled-up, full system-level modeling. Both experimental test results and full wave simulation results are used to validate the foundational model.

Evaluation of statistical distributions to analyze the pollution of Cd and Pb in urban runoff.

PubMed

Toranjian, Amin; Marofi, Safar

2017-05-01

Heavy metal pollution in urban runoff causes severe environmental damage. Identification of these pollutants and their statistical analysis is necessary to provide management guidelines. In this study, 45 continuous probability distribution functions were selected to fit the Cd and Pb data in the runoff events of an urban area during October 2014-May 2015. The sampling was conducted from the outlet of the city basin during seven precipitation events. For evaluation and ranking of the functions, we used the goodness of fit Kolmogorov-Smirnov and Anderson-Darling tests. The results of Cd analysis showed that Hyperbolic Secant, Wakeby and Log-Pearson 3 are suitable for frequency analysis of the event mean concentration (EMC), the instantaneous concentration series (ICS) and instantaneous concentration of each event (ICEE), respectively. In addition, the LP3, Wakeby and Generalized Extreme Value functions were chosen for the EMC, ICS and ICEE related to Pb contamination.

Light-assisted drying (LAD) of small volume biologics: a comparison of two IR light sources

NASA Astrophysics Data System (ADS)

Young, Madison A.; Van Vorst, Matthew; Elliott, Gloria D.; Trammell, Susan R.

2016-03-01

Protein therapeutics have been developed to treat diseases ranging from arthritis and psoriasis to cancer. A challenge in the development of protein-based drugs is maintaining the protein in the folded state during processing and storage. We are developing a novel processing method, light-assisted drying (LAD), to dehydrate proteins suspended in a sugar (trehalose) solution for storage at supra-zero temperatures. Our technique selectively heats the water in small volume samples using near-IR light to speed dehydration which prevents sugar crystallization that can damage embedded proteins. In this study, we compare the end moisture content (EMC) as a function of processing time of samples dried with two different light sources, Nd:YAG (1064 nm) and Thulium fiber (1850 nm) lasers. EMC is the ratio of water to dry weight in a sample and the lower the EMC the higher the possible storage temperature. LAD with the 1064 and 1850 nm lasers yielded 78% and 65% lower EMC, respectively, than standard air-drying. After 40 minutes of LAD with 1064 and 1850 nm sources, EMCs of 0.27+/-.27 and 0.15+/-.05 gH2O/gDryWeight were reached, which are near the desired value of 0.10 gH2O/gDryWeight that enables storage in a glassy state without refrigeration. LAD is a promising new technique for the preparation of biologics for anhydrous preservation.

Evaluation of the Eclipse eMC algorithm for bolus electron conformal therapy using a standard verification dataset.

PubMed

Carver, Robert L; Sprunger, Conrad P; Hogstrom, Kenneth R; Popple, Richard A; Antolak, John A

2016-05-08

The purpose of this study was to evaluate the accuracy and calculation speed of electron dose distributions calculated by the Eclipse electron Monte Carlo (eMC) algorithm for use with bolus electron conformal therapy (ECT). The recent com-mercial availability of bolus ECT technology requires further validation of the eMC dose calculation algorithm. eMC-calculated electron dose distributions for bolus ECT have been compared to previously measured TLD-dose points throughout patient-based cylindrical phantoms (retromolar trigone and nose), whose axial cross sections were based on the mid-PTV (planning treatment volume) CT anatomy. The phantoms consisted of SR4 muscle substitute, SR4 bone substitute, and air. The treatment plans were imported into the Eclipse treatment planning system, and electron dose distributions calculated using 1% and < 0.2% statistical uncertainties. The accuracy of the dose calculations using moderate smoothing and no smooth-ing were evaluated. Dose differences (eMC-calculated less measured dose) were evaluated in terms of absolute dose difference, where 100% equals the given dose, as well as distance to agreement (DTA). Dose calculations were also evaluated for calculation speed. Results from the eMC for the retromolar trigone phantom using 1% statistical uncertainty without smoothing showed calculated dose at 89% (41/46) of the measured TLD-dose points was within 3% dose difference or 3 mm DTA of the measured value. The average dose difference was -0.21%, and the net standard deviation was 2.32%. Differences as large as 3.7% occurred immediately distal to the mandible bone. Results for the nose phantom, using 1% statistical uncertainty without smoothing, showed calculated dose at 93% (53/57) of the measured TLD-dose points within 3% dose difference or 3 mm DTA. The average dose difference was 1.08%, and the net standard deviation was 3.17%. Differences as large as 10% occurred lateral to the nasal air cavities. Including smoothing had insignificant effects on the accuracy of the retromolar trigone phantom calculations, but reduced the accuracy of the nose phantom calculations in the high-gradient dose areas. Dose calculation times with 1% statistical uncertainty for the retromolar trigone and nose treatment plans were 30 s and 24 s, respectively, using 16 processors (Intel Xeon E5-2690, 2.9 GHz) on a framework agent server (FAS). In comparison, the eMC was significantly more accurate than the pencil beam algorithm (PBA). The eMC has comparable accuracy to the pencil beam redefinition algorithm (PBRA) used for bolus ECT planning and has acceptably low dose calculation times. The eMC accuracy decreased when smoothing was used in high-gradient dose regions. The eMC accuracy was consistent with that previously reported for accuracy of the eMC electron dose algorithm and shows that the algorithm is suitable for clinical implementation of bolus ECT.

National Centers for Environmental Prediction

Science.gov Websites

Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post / VISION | About EMC EMC > Mesoscale Modeling > IMPLEMENTATION INFO Home Mission Models R & D ; Extratropical Cyclone Tracks & Verification Implementation Info FAQ Disclaimer More Info MESOSCALE MODELING

National Centers for Environmental Prediction

Science.gov Websites

Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post / VISION | About EMC EMC > Mesoscale Modeling > Home Mission Models R & D Collaborators Cyclone Tracks & Verification Implementation Info FAQ Disclaimer More Info MESOSCALE MODELING JUMP TO

National Centers for Environmental Prediction

Science.gov Websites

Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post / VISION | About EMC EMC > Mesoscale Modeling > MODELS Home Mission Models R & D Collaborators Cyclone Tracks & Verification Implementation Info FAQ Disclaimer More Info MESOSCALE MODELING SREF

National Centers for Environmental Prediction

Science.gov Websites

Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post / VISION | About EMC EMC > Mesoscale Modeling > CALENDAR Home Mission Models R & D Collaborators Cyclone Tracks & Verification Implementation Info FAQ Disclaimer More Info MESOSCALE MODELING CALENDAR

National Centers for Environmental Prediction

Science.gov Websites

Modeling Mesoscale Modeling Marine Modeling and Analysis Teams Climate Data Assimilation Ensembles and Post / VISION | About EMC EMC > Mesoscale Modeling > R & D Home Mission Models R & D Collaborators Cyclone Tracks & Verification Implementation Info FAQ Disclaimer More Info MESOSCALE MODELING Air

OBSERVATIONAL DATA PROCESSING AT NCEP

Science.gov Websites

operations, but also for research and study. 2. The various NCEP networks access the observational data base Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar / VISION | About EMC Observational Data Processing at NCEP Dennis Keyser - NOAA/NWS/NCEP/EMC (Last Revised

75 FR 43555 - Hewlett Packard; Hewlett Packard-Enterprise Business Services Formerly Known as Electronic Data...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-26

... Workers From Sun Microsystems, Inc., Dell Computer Corp., EMC Corp., EMC Corp. Total, Cisco Systems Capital Corporation, Microsoft Corp., Symantec Corp., Xerox Corp., Vmware, Inc., Sun Microsystems Federal... known as Electronic Data Systems, including on- site leased workers from Sun Microsystems, Inc., Dell...

75 FR 63509 - Hewlett Packard, Hewlett Packard-Enterprise Business Services, Formerly Known as Electronic Data...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-15

... Workers From Sun Microsystems, Inc., Dell Computer Corp., EMC Corp., EMC Corp. Total, Cisco Systems Capital Corporation, Microsoft Corp., Symantec Corp., Xerox Corp., VMWare, Inc., Sun Microsystems Federal...-- Services, formerly known as Electronic Data Systems, including on- site leased workers from Sun...

Testing quantum chromodynamics in electroproduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brodsky, S.J.

1987-05-01

The exclusive channels in electroproduction are discussed. The study of color transparency, the formation zone, and other novel aspects of QCD by measuring exclusive reactions inside nuclear targets is covered. Diffractive electroproduction channels are discussed, and exclusive nuclear processes in QCD are examined. Non-additivity of nuclear structure functions (EMC effect) is also discussed, as well as jet coalescence in electroproduction. (LEW)

40 CFR Appendix A - Protocol for Using an Electrochemical Analyzer to Determine Oxygen and Carbon Monoxide...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., and Process Heaters Using Portable Analyzers”, EMC Conditional Test Protocol 30 (CTM-30), Gas Research... cell design(s) conforming to this protocol will determine the analytical range for each gas component..., selective gas scrubbers, etc.) to meet the design specifications of this protocol. Do not make changes to...

40 CFR Appendix A - Protocol for Using an Electrochemical Analyzer to Determine Oxygen and Carbon Monoxide...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., and Process Heaters Using Portable Analyzers”, EMC Conditional Test Protocol 30 (CTM-30), Gas Research... cell design(s) conforming to this protocol will determine the analytical range for each gas component..., selective gas scrubbers, etc.) to meet the design specifications of this protocol. Do not make changes to...

Thematic mapper flight model preshipment review data package. Volume 3, part A: System data

NASA Technical Reports Server (NTRS)

1982-01-01

Results of vibration, acoustical noise, and thermal vacuum are described as well as tests studies of EMI/EMC and mass properties conducted for thematic mapper systems integration. Liens are summarized and the engineering change proposal status is presented. Requests for deviation/waiver are included along with failure and nonforming material reports.

NCEP Operational HWRF Forecasting System

Science.gov Websites

NOAA logo - Click to go to the NOAA homepage EMC Hurricane Team NWS logo - Click to go to the NWS © 2018 | NOAA * NWS * NCEP * EMC * Hurricane Project Team DISCLAIMER: THIS INFORMATION IS PROVIDED AS GUIDANCE. IT REQUIRES INTERPRETATION BY HURRICANE SPECIALISTS AND SHOULD NOT BE CONSIDERED AS A FINAL

National Centers for Environmental Prediction

Science.gov Websites

Mailing Lists There are two listservs for the MTT group: announce and discuss To join the listservs go here: Announce - https://lstsrv.ncep.noaa.gov/mailman/listinfo/ncep.list.emc_porting-announce Discuss - https://lstsrv.ncep.noaa.gov/mailman/listinfo/ncep.list.emc_porting-discuss To email the lists: Announce

NCEP SST Analysis

Science.gov Websites

Branches Global Climate & Weather Modeling Mesoscale Modeling Marine Modeling and Analysis Contact EMC Weather Service NWS logo - Click to go to the NWS homepage Environmental Modeling Center Home News Organization Search Go Search Polar Go MMAB SST Analysis Main page About MMAB Our Mission Our Personnel EMC

EMC: Air Quality Forecast Home page

Science.gov Websites

archive NAM Verification Meteorology Error Time Series EMC NAM Spatial Maps Real Time Mesoscale Analysis Precipitation verification NAQFC VERIFICATION CMAQ Ozone & PM Error Time Series AOD Error Time Series HYSPLIT Smoke forecasts vs GASP satellite Dust and Smoke Error Time Series HYSPLIT WCOSS Upgrade (July

Equilibrium Moisture Content of Common Fine Fuels in Southeastern Forests

Treesearch

W.H. Blackmarr

1971-01-01

Nine different kinds of forest litter found in ground fuel complexes of southeastern forests were subjected to step-wise changes in relative humidity to determine their equilibrium moisture content (EMC) at different levels of relative humidity. The adsorption and desorption EMC curves for these fuels exhibited the typical hysteresis loop...

Effects of Solvent Composition on Liquid Range, Glass Transition, and Conductivity of Electrolytes of a (Li, Cs)PF 6 Salt in EC-PC-EMC Solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Michael S.; Li, Qiuyan; Li, Xing

Electrolytes of 1 M LiPF 6 (lithium hexafluorophosphate) and 0.05 M CsPF 6 (cesium hexafluorophosphate) in EC-PC-EMC (ethylene carbonate-propylene carbonate-ethyl methyl carbonate) solvents of varying solvent compositions were studied for the effects of solvent composition on the lower limit of liquid range, viscosity (as reflected by the glass transition temperature), and electrolytic conductivity. In addition, a ternary phase diagram of EC-PC-EMC was constructed and crystallization temperatures of EC and EMC were calculated to assist the interpretation and understanding of the change of liquid range with solvent composition. A function based on Vogel-Fulcher-Tammann equation was fitted to the conductivity data inmore » their entirety and plotted as conductivity surfaces in solvent composition space for more direct and clear comparisons and discussions. Changes of viscosity and dielectric constant of the solvents with their composition, in relation to those of the solvent components, were found to be underlying many of the processes studied.« less

Storm runoff quality and pollutant loading from commercial, residential, and industrial catchments in the tropic.

PubMed

Chow, M F; Yusop, Z; Shirazi, S M

2013-10-01

Information on the pollution level and the influence of hydrologic regime on the stormwater pollutant loading in tropical urban areas are still scarce. More local data are still required because rainfall and runoff generation processes in tropical environment are very different from the temperate regions. This study investigated the extent of urban runoff pollution in residential, commercial, and industrial catchments in the south of Peninsular Malaysia. Stormwater samples and flow rate data were collected from 51 storm events. Samples were analyzed for total suspended solids, 5-day biochemical oxygen demand, chemical oxygen demand, oil and grease (O&G), nitrate nitrogen (NO3-N), nitrite nitrogen, ammonia nitrogen, soluble reactive phosphorus, total phosphorus (TP), and zinc (Zn). It was found that the event mean concentrations (EMCs) of pollutants varied greatly between storm characteristics and land uses. The results revealed that site EMCs for residential catchment were lower than the published data but higher for the commercial and industrial catchments. All rainfall variables were negatively correlated with EMCs of most pollutants except for antecedent dry days (ADD). This study reinforced the earlier findings on the importance of ADD for causing greater EMC values with exceptions for O&G, NO3-N, TP, and Zn. In contrast, the pollutant loadings are influenced primarily by rainfall depth, mean intensity, and max 5-min intensity in all the three catchments. Overall, ADD is an important variable in multiple linear regression models for predicting the EMC values in the tropical urban catchments.

Poster - Thur Eve - 45: Commissioning of the Varian ECLIPSE eMC algorithm for clinical electron treatment planning.

PubMed

Serban, M; Ruo, R; Sarfehnia, A; Parker, W; Evans, M

2012-07-01

Fast electron Monte Carlo systems have been developed commercially, and implemented for clinical practice in radiation therapy clinics. In this work the Varian eMC (electron Monte Carlo) algorithm was commissioned for clinical electron beams of energies between 6 MeV and 20 MeV. Beam outputs, PDDs and profiles were measured for 29 regular and irregular cutouts using the IC-10 (Wellhöfer) ionization chamber. Detailed percentage depth dose comparisons showed that the agreement between measurement and eMC for different characteristic points on the PDD are generally less than 1 mm and always less than 2 mm, with the eMC calculated values being lower than the measured values. Of the 145 measured output factors, 19 cases fail a ±2% agreement but only 8 cases fail a ±3% agreement between calculation and measurement. Comparison of central axis dose distributions for two electron energies (9, and 20 MeV) for a 10 × 10 cm 2 field, centrally shielded with Pb of width 0 cm (open), 1, 2 and 3 cm, shows agreement to within 3% except near the surface. Comparison of central axis dose distributions for 9 MeV in heterogeneous phantoms including bone and lung inserts showed agreement of 1 mm and 3 mm respectively with measured TLD data. The overall agreement between measurement and eMC calculation has enabled us to begin implementing this calculation model for clinical use. © 2012 American Association of Physicists in Medicine.

Designing Collaborative Developmental Standards by Refactoring of the Earth Science Models, Libraries, Workflows and Frameworks.

NASA Astrophysics Data System (ADS)

Mirvis, E.; Iredell, M.

2015-12-01

The operational (OPS) NOAA National Centers for Environmental Prediction (NCEP) suite, traditionally, consist of a large set of multi- scale HPC models, workflows, scripts, tools and utilities, which are very much depending on the variety of the additional components. Namely, this suite utilizes a unique collection of the in-house developed 20+ shared libraries (NCEPLIBS), certain versions of the 3-rd party libraries (like netcdf, HDF, ESMF, jasper, xml etc.), HPC workflow tool within dedicated (sometimes even vendors' customized) HPC system homogeneous environment. This domain and site specific, accompanied with NCEP's product- driven large scale real-time data operations complicates NCEP collaborative development tremendously by reducing chances to replicate this OPS environment anywhere else. The NOAA/NCEP's Environmental Modeling Center (EMC) missions to develop and improve numerical weather, climate, hydrological and ocean prediction through the partnership with the research community. Realizing said difficulties, lately, EMC has been taken an innovative approach to improve flexibility of the HPC environment by building the elements and a foundation for NCEP OPS functionally equivalent environment (FEE), which can be used to ease the external interface constructs as well. Aiming to reduce turnaround time of the community code enhancements via Research-to-Operations (R2O) cycle, EMC developed and deployed several project sub-set standards that already paved the road to NCEP OPS implementation standards. In this topic we will discuss the EMC FEE for O2R requirements and approaches in collaborative standardization, including NCEPLIBS FEE and models code version control paired with the models' derived customized HPC modules and FEE footprints. We will share NCEP/EMC experience and potential in the refactoring of EMC development processes, legacy codes and in securing model source code quality standards by using combination of the Eclipse IDE, integrated with the reverse engineering tools/APIs. We will also inform on collaborative efforts in the restructuring of the NOAA Environmental Modeling System (NEMS) - the multi- model and coupling framework, and transitioning FEE verification methodology.

TSA suppresses miR-106b-93-25 cluster expression through downregulation of MYC and inhibits proliferation and induces apoptosis in human EMC.

PubMed

Zhao, Zhi-Ning; Bai, Jiu-Xu; Zhou, Qiang; Yan, Bo; Qin, Wei-Wei; Jia, Lin-Tao; Meng, Yan-Ling; Jin, Bo-Quan; Yao, Li-Bo; Wang, Tao; Yang, An-Gang

2012-01-01

Histone deacetylase (HDAC) inhibitors are emerging as a novel class of anti-tumor agents and have manifested the ability to decrease proliferation and increase apoptosis in different cancer cells. A significant number of genes have been identified as potential effectors responsible for the anti-tumor function of HDAC inhibitor. However, the molecular mechanisms of these HDAC inhibitors in this process remain largely undefined. In the current study, we searched for microRNAs (miRs) that were affected by HDAC inhibitor trichostatin (TSA) and investigated their effects in endometrial cancer (EMC) cells. Our data showed that TSA significantly inhibited the growth of EMC cells and induced their apoptosis. Among the miRNAs that altered in the presence of TSA, the miR-106b-93-25 cluster, together with its host gene MCM7, were obviously down-regulated in EMC cells. p21 and BIM, which were identified as target genes of miR-106b-93-25 cluster, increased in TSA treated tumor cells and were responsible for cell cycle arrest and apoptosis. We further identified MYC as a regulator of miR-106b-93-25 cluster and demonstrated its down-regulation in the presence of TSA resulted in the reduction of miR-106b-93-25 cluster and up-regulation of p21 and BIM. More important, we found miR-106b-93-25 cluster was up-regulated in clinical EMC samples in association with the overexpression of MCM7 and MYC and the down-regulation of p21 and BIM. Thus our studies strongly indicated TSA inhibited EMC cell growth and induced cell apoptosis and cell cycle arrest at least partially through the down-regulation of the miR-106b-93-25 cluster and up-regulation of it's target genes p21 and BIM via MYC.

SU-F-T-74: Experimental Validation of Monaco Electron Monte Carlo Dose Calculation for Small Fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Varadhan; Way, S; Arentsen, L

2016-06-15

Purpose: To verify experimentally the accuracy of Monaco (Elekta) electron Monte Carlo (eMC) algorithm to calculate small field size depth doses, monitor units and isodose distributions. Methods: Beam modeling of eMC algorithm was performed for electron energies of 6, 9, 12 15 and 18 Mev for a Elekta Infinity Linac and all available ( 6, 10, 14 20 and 25 cone) applicator sizes. Electron cutouts of incrementally smaller field sizes (20, 40, 60 and 80% blocked from open cone) were fabricated. Dose calculation was performed using a grid size smaller than one-tenth of the R{sub 80–20} electron distal falloff distancemore » and number of particle histories was set at 500,000 per cm{sup 2}. Percent depth dose scans and beam profiles at dmax, d{sub 90} and d{sub 80} depths were measured for each cutout and energy with Wellhoffer (IBA) Blue Phantom{sup 2} scanning system and compared against eMC calculated doses. Results: The measured dose and output factors of incrementally reduced cutout sizes (to 3cm diameter) agreed with eMC calculated doses within ± 2.5%. The profile comparisons at dmax, d{sub 90} and d{sub 80} depths and percent depth doses at reduced field sizes agreed within 2.5% or 2mm. Conclusion: Our results indicate that the Monaco eMC algorithm can accurately predict depth doses, isodose distributions, and monitor units in homogeneous water phantom for field sizes as small as 3.0 cm diameter for energies in the 6 to 18 MeV range at 100 cm SSD. Consequently, the old rule of thumb to approximate limiting cutout size for an electron field determined by the lateral scatter equilibrium (E (MeV)/2.5 in centimeters of water) does not apply to Monaco eMC algorithm.« less

Human coronavirus EMC does not require the SARS-coronavirus receptor and maintains broad replicative capability in mammalian cell lines.

PubMed

Müller, Marcel A; Raj, V Stalin; Muth, Doreen; Meyer, Benjamin; Kallies, Stephan; Smits, Saskia L; Wollny, Robert; Bestebroer, Theo M; Specht, Sabine; Suliman, Tasnim; Zimmermann, Katrin; Binger, Tabea; Eckerle, Isabella; Tschapka, Marco; Zaki, Ali M; Osterhaus, Albert D M E; Fouchier, Ron A M; Haagmans, Bart L; Drosten, Christian

2012-12-11

A new human coronavirus (hCoV-EMC) has emerged very recently in the Middle East. The clinical presentation resembled that of the severe acute respiratory syndrome (SARS) as encountered during the epidemic in 2002/2003. In both cases, acute renal failure was observed in humans. HCoV-EMC is a member of the same virus genus as SARS-CoV but constitutes a sister species. Here we investigated whether it might utilize angiotensin-converting enzyme 2 (ACE2), the SARS-CoV receptor. Knowledge of the receptor is highly critical because the restriction of the SARS receptor to deep compartments of the human respiratory tract limited the spread of SARS. In baby hamster kidney (BHK) cells, lentiviral transduction of human ACE2 (hACE2) conferred permissiveness and replication for SARS-CoV but not for hCoV-EMC. Monkey and human kidney cells (LLC-MK2, Vero, and 769-P) and swine kidney cells were permissive for both viruses, but only SARS-CoV infection could be blocked by anti-hACE2 antibody and could be neutralized by preincubation of virus with soluble ACE2. Our data show that ACE2 is neither necessary nor sufficient for hCoV-EMC replication. Moreover, hCoV-EMC, but not SARS-CoV, replicated in cell lines from Rousettus, Rhinolophus, Pipistrellus, Myotis, and Carollia bats, representing four major chiropteran families from both suborders. As human CoV normally cannot replicate in bat cells from different families, this suggests that hCoV-EMC might use a receptor molecule that is conserved in bats, pigs, and humans, implicating a low barrier against cross-host transmission. IMPORTANCE A new human coronavirus (hCoV) emerged recently in the Middle East. The disease resembled SARS (severe acute respiratory syndrome), causing a fatal epidemic in 2002/2003. Coronaviruses have a reservoir in bats and because this novel virus is related to SARS-CoV, we investigated whether it might replicate in bat cells and use the same receptor (angiotensin-converting enzyme 2 [ACE2]). This knowledge is highly critical, because the SARS-CoV receptor influenced pathology, and its localization in the deep respiratory tract is thought to have restricted the transmissibility of SARS. Our data show that hCoV-EMC does not need the SARS-CoV receptor to infect human cells. Moreover, the virus is capable of infecting human, pig, and bat cells. This is remarkable, as human CoVs normally cannot replicate in bat cells as a consequence of host adaptation. Our results implicate that the new virus might use a receptor that is conserved between bats, pigs and humans suggesting a low barrier against cross-host transmission.

Fuel Injection Strategy for a Next Generation Pulse Detonation Engine

DTIC Science & Technology

2006-06-01

at 45°C CE Approved EMC EMC Directive 89/336/EEC; EN 61326-1 Emissions and Immunity Safety Low Voltage Directive 73/23/EEC; EN 61010 -1...Operating Humidity 0–90% Nonoperating Humidity 0–100% CDRH Class IIIb IEC Class 3B From www.mellesgriot.com 47 SILICON OPTICAL SENSOR Model

Teaching E=mc2: An Exploration of Some Issues.

ERIC Educational Resources Information Center

Baierlein, Ralph

1991-01-01

A discussion of what E=mc2 means and other issues associated with the equation are presented. The differences between matter, mass, and energy, a derivation of the equation, the history of the word mass and examples of how it is used, misconceptions surrounding the equation, and a discussion of uranium fission are included. (KR)

Simple Statistical Model to Quantify Maximum Expected EMC in Spacecraft and Avionics Boxes

NASA Technical Reports Server (NTRS)

Trout, Dawn H.; Bremner, Paul

2014-01-01

This study shows cumulative distribution function (CDF) comparisons of composite a fairing electromagnetic field data obtained by computational electromagnetic 3D full wave modeling and laboratory testing. Test and model data correlation is shown. In addition, this presentation shows application of the power balance and extention of this method to predict the variance and maximum exptected mean of the E-field data. This is valuable for large scale evaluations of transmission inside cavities.

Bilateral comparison on electric field measurements between TÜBİTAK UME and SASO NMCC

NASA Astrophysics Data System (ADS)

Aslan, Çağlar; Alrobaish, Abdullah M.; Şen, Osman

2017-01-01

Electromagnetic (EM) probes are widely utilized in the measurement of EM fields for non-ionizing radiation, electromagnetic compatibility (EMC) testing and other applications in the frequency range 5 Hz-60 GHz. They must be calibrated by National Metrology Institutes (NMIs) or accredited calibration laboratories in accordance with international standards such as IEEE 1309. The existing NMIs or emerging NMIs should refer to the international comparison measurements in order to assure the quality of their measurement results. Therefore, the electric field comparison measurements organized by TUBITAK UME were performed between TUBITAK UME and SASO NMCC at the 100 Hz, 1 kHz, 10 MHz, 100 MHz, 1 GHz, 10 GHz and 18 GHz frequencies in order to obtain the correction factors of the electric field probes. The comparison measurements were carried out in accordance with the Technical Protocol prepared by TUBITAK UME. The measurements started in October 2017 and were completed in January 2017. There was good agreement found for the correction factors. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final Environmental Assessment: Demolition of Barracks (Building T-2) at Ipswich Antenna Test Facility

DTIC Science & Technology

2011-12-01

EIAP), managed the preparation and was the primary author of this environmental assessment. QAULITY ASSURANCE LEADER Cravedi, Gregory. 66 ABG/CE...BMP Best Management Practice CEQ Council on Environmental Quality CERCLA Comprehensive Environmental Response, Compensation, and Liability Act...Assessment EMCS Energy Management Control System ESC Electronic Systems Center FEMA Federal Emergency Management Agency FIRM Federal

Influence of moisture on brown-rot fungal attack on wood

Treesearch

R.M. Rowell; R.E. Ibach; T. Nilsson

2007-01-01

Southern pine solid wood and wood fiber were reacted with acetic anhydride to various acetyl weight gains. The equilibrium moisture content (EMC) was determined on these specimens at 30%, 65% and 90% relative humidity (RH) and 27 °C. A standard soil block decay test using the brown-rot fungus Gloeophyllum trabeum was performed and weight loss calculated. Two...

[Role of an educational-and-methodological complex in the optimization of teaching at the stage of additional professional education of physicians in the specialty "anesthesiology and reanimatology"].

PubMed

Buniatian, A A; Sizova, Zh M; Vyzhigina, M A; Shikh, E V

2010-01-01

An educational-and-methodological complex (EMC) in the specialty 'Anesthesiology and Reanimatology", which promotes manageability, flexibility, and dynamism of an educational process, is of great importance in solving the problem in the systematization of knowledge and its best learning by physicians at a stage of additional professional education (APE). EMC is a set of educational-and-methodological materials required to organize and hold an educational process for the advanced training of anesthesiologists and resuscitation specialists at the stage of APE. EMC includes a syllabus for training in the area "Anesthesiology and Reanimatology" by the appropriate training pattern (certification cycles, topical advanced training cycles); a work program for training in the specialty "Anesthesiology and Reanimatology"; a work curriculums for training in allied specialties (surgery, traumatology and orthopedics, obstetrics and gynecology, and pediatrics); work programs on basic disciplines (pharmacology, normal and pathological physiology, normal anatomy, chemistry and biology); working programs on the area "Public health care and health care service", guidelines for the teacher; educational-and-methodological materials for the student; and quiz programs. The main point of EMC in the specialty "Anesthesiology and Reanimatology" is a work program. Thus, educational-and-methodological and teaching materials included into the EMC in the specialty 'Anesthesiology and Reanimatology" should envisage the logically successive exposition of a teaching material, the use of currently available methods and educational facilities, which facilitates the optimization of training of anesthesiologists and resuscitation specialists at the stage of APE.

Antenna Measurements: Test & Analysis of the Radiated Emissions from the NASA/Orion Spacecraft - Parachute System Simulator

NASA Technical Reports Server (NTRS)

Norgard, John D.

2012-01-01

For future NASA Manned Space Exploration of the Moon and Mars, a blunt body capsule, called the Orion Crew Exploration Vehicle (CEV), composed of a Crew Module (CM) and a Service Module (SM), with a parachute decent assembly is planned for reentry back to Earth. A Capsule Parachute Assembly System (CPAS) is being developed for preliminary parachute drop tests at the Yuma Proving Ground (YPG) to simulate high-speed reentry to Earth from beyond Low-Earth-Orbit (LEO) and to provide measurements of landing parameters and parachute loads. The avionics systems on CPAS also provide mission critical firing events to deploy, reef, and release the parachutes in three stages (extraction, drogues, mains) using mortars and pressure cartridge assemblies. In addition, a Mid-Air Delivery System (MDS) is used to separate the capsule from the sled that is used to eject the capsule from the back of the drop plane. Also, high-speed and high-definition cameras in a Video Camera System (VCS) are used to film the drop plane extraction and parachute landing events. To verify Electromagnetic Compatibility (EMC) of the CPAS system from unintentional radiation, Electromagnetic Interference (EMI) measurements are being made inside a semi-anechoic chamber at NASA/JSC at 1m from the electronic components of the CPAS system. In addition, EMI measurements of the integrated CPAS system are being made inside a hanger at YPG. These near-field B-Dot probe measurements on the surface of a parachute simulator (DART) are being extrapolated outward to the 1m standard distance for comparison to the MIL-STD radiated emissions limit.

Investigation of Historic Equilibrium Moisture Content Data from the Forest Products Laboratory

Treesearch

Samuel V. Glass; Samuel L. Zelinka; Jay A. Johnson

2014-01-01

The Forest Products Laboratory (FPL) has provided equilibrium moisture content (EMC) values of wood for given temperature and relative humidity (RH) conditions in various forms over the course of its history, primarily for practical purposes related to drying lumber and controlling moisture content. The FPL EMC data have been widely cited and reprinted, not only in...

Frequent electronic media communication with friends is associated with higher adolescent substance use.

PubMed

Gommans, Rob; Stevens, Gonneke W J M; Finne, Emily; Cillessen, Antonius H N; Boniel-Nissim, Meyran; ter Bogt, Tom F M

2015-02-01

This study investigated the unique associations between electronic media communication (EMC) with friends and adolescent substance use (tobacco, alcohol, and cannabis), over and beyond the associations of face-to-face (FTF) interactions with friends and the average level of classroom substance use. Drawn from the cross-national 2009/2010 Health Behaviour in School-aged Children (HBSC) study in The Netherlands, 5,642 Dutch adolescents (Mage = 14.29) reported on their substance use, EMC, and FTF interactions. Two-level multilevel analyses (participants nested within classrooms) were run. Electronic media communication was positively associated with adolescent substance use, though significantly more strongly with alcohol (β = 0.15, SEβ = 0.02) than with tobacco (β = 0.05, SEβ = 0.02, t (5,180) = 3.33, p < 0.001) or cannabis use (β = 0.06, SEβ = 0.02, t (5,160) = 2.79, p < 0.01). Further, EMC strengthened several positive associations of FTF interactions and average classroom substance use with adolescent substance use. Electronic media communication was uniquely associated with substance use, predominantly with alcohol use. Thus, adolescents' EMC and other online behaviors should not be left unnoticed in substance use research and prevention programs.

Exploring Sea Quark EMC Effect and Anti-Shadowing Through Drell-Yan at SeaQuest / Fermilab E906

NASA Astrophysics Data System (ADS)

Dannowitz, Bryan; Fermilab E906 / SeaQuest Collaboration

2015-04-01

Fermilab E906/SeaQuest is a fixed-target experiment that uses the 120 GeV Main Injector proton beam. SeaQuest will extract sea anti-quark structure of the proton by detecting dimuon pairs created by Drell-Yan and measuring the cross-section ratios for LH2, LD2, C, Fe, and W targets. The European Muon Collaboration (EMC) discovered that the momentum distribution of quarks in a free nucleon becomes modified when bound within a nucleus. In studying the EMC Effect, an anti-shadowing feature has been observed in DIS and pion-induced DY measurements in the 0 . 1

Automated culture system experiments hardware: developing test results and design solutions.

PubMed

Freddi, M; Covini, M; Tenconi, C; Ricci, C; Caprioli, M; Cotronei, V

2002-07-01

The experiment proposed by Prof. Ricci University of Milan is funded by ASI with Laben as industrial Prime Contractor. ACS-EH (Automated Culture System-Experiment Hardware) will support the multigenerational experiment on weightlessness with rotifers and nematodes within four Experiment Containers (ECs) located inside the European Modular Cultivation System (EMCS) facility..Actually the Phase B is in progress and a concept design solution has been defined. The most challenging aspects for the design of such hardware are, from biological point of view the provision of an environment which permits animal's survival and to maintain desiccated generations separated and from the technical point of view, the miniaturisation of the hardware itself due to the reduce EC provided volume (160mmx60mmx60mm). The miniaturisation will allow a better use of the available EMCS Facility resources (e.g. volume. power etc.) and to fulfil the experiment requirements. ACS-EH, will be ready to fly in the year 2005 on boar the ISS.

Chemistry of green encapsulating molding compounds at interfaces with other materials in electronic devices

NASA Astrophysics Data System (ADS)

Scandurra, A.; Zafarana, R.; Tenya, Y.; Pignataro, S.

2004-07-01

The interface chemistry between encapsulating epoxy phenolic molding compound (EMC) containing phosphorous based organic flame retardant (the so called "green materials") and copper oxide-hydroxide and aluminum oxide-hydroxide surfaces have been studied in comparison with "conventional" EMC containing bromine and antimony as flame retardant. These green materials are designed to reduce the presence of toxic elements in the electronic packages and, consequently, in the environment. For the study were used a Scanning Acoustic Microscopy for delamination measurements, a dynamometer for the pull strength measurements and an ESCA spectrometer for chemical analysis of the interface. The general behavior of the green compound in terms of delamination, adhesion, and corrosion is found better or at least comparable than that of the conventional EMC.

Advanced Patient Data Replication and Recovery

DTIC Science & Technology

2010-10-01

Patient Data Protection (APDAPT) Eisenhower Medical Center (EMC) is attempting to lower the risk of losing patient data, as well as the risk...includes radiological images. EMC has made a multi-million dollar investment in the digitization of patient data; the Electronic Medical Record (EMR...storage and retrieval of the patient chart or EMR. The EMR is comprised of patient vital signs, nurse notes, medications administered, doctors

Randomized controlled study of early medication change for non-improvers to antidepressant therapy in major depression--The EMC trial.

PubMed

Tadić, André; Wachtlin, Daniel; Berger, Mathias; Braus, Dieter F; van Calker, Dietrich; Dahmen, Norbert; Dreimüller, Nadine; Engel, Alice; Gorbulev, Stanislav; Helmreich, Isabella; Kaiser, Anne-Katrin; Kronfeld, Kai; Schlicht, Konrad F; Tüscher, Oliver; Wagner, Stefanie; Hiemke, Christoph; Lieb, Klaus

2016-04-01

Patients with Major Depressive Disorder (MDD) and no improvement after two weeks of antidepressant pharmacotherapy have a high risk of treatment failure. The aim of the study was to determine whether an early medication change (EMC) strategy is superior to a guideline-based treatment in MDD patients without improvement after two weeks of antidepressant pharmacotherapy. Eight-hundred-and-eighty-nine patients with MDD were enrolled, 879 patients received the SSRI escitalopram. Of those, 192 patients had no improvement, defined as a reduction of < 20% on the Hamilton Depression Rating Scale (HAMD-17) after 14 days of treatment, and were randomly assigned to open treatment with the EMC strategy (n = 97; venlafaxine XR for study days 15-56; in case of sustained non-improvement on day 28, lithium augmentation for days 29-56) or TAU (n = 95; escitalopram continuation; non-responders on day 28 were switched to venlafaxine XR for four weeks, i.e. days 29-56). The primary outcome was remission (HAMD-17 ≤ 7) after 8 weeks of treatment as assessed by blinded raters. Remission rates were 24% for EMC and 16% for TAU, which was not significantly different (p = 0.2056). Sensitivity analyses for the primary and secondary effectiveness endpoints consistently showed favorable results for patients randomized to EMC. The results confirm data from post-hoc analyses of clinical trials showing that early non-improvement identifies patients who likely need alternate interventions. However, the herein used two-step switch/augmentation strategy for this risk group was not more effective than the control intervention. Alternate strategies and other design aspects are discussed in order to support researchers addressing the same research question. Copyright © 2016 Elsevier B.V. and ECNP. All rights reserved.

Respiratory and intraperitoneal infection of mice with encephalomyocarditis virus: effect of sublethal x-irradiation on host resistance and survival

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bogaerts, W.J.C.; Durville-vanderoord, B.J.

1975-01-01

The relationships governing host resistance to viral infection were evaluated in mice following respiratory or peritoneal infection with three strains of encephalomyocarditis (EMC) virus, which were antigenically similar but differed in virulence. Host resistance to each strain was evaluated by determining the mean lethal dose LD50, and the mean infectious dose ID50. The contribution of non-specific resistance to the overall defense of the host was assessed in mice that had received 450 R of x irradiation prior to viral infection. Experimental results indicate that host capacity to resist respiratory infection exceeds that for peritoneal infection for the three EMC strains.more » It is concluded that respiratory inoculation of virus affords better immunization against EMC virus infection than does peritoneal infection. (Author) (GRA)« less

[First flush effects of storm events of Baoxiang River in Lake Dianchi Watershed].

PubMed

Guo, Huai-Cheng; Xiang, Nan; Zhou, Feng; Wang, Yong-Hua; Li, Fa-Rong; Zhu, Xiang; Mao, Guo-Zhu; Yu, Shu-Xia; Li, Na; Sheng, Hu; Yang, Yong-Hui; He, Cheng-Jie; Wang, Cui-Yu

2013-04-01

To understand riverine process of non-point source effectively, first flush effects of storm events were investigated at Baoxiang River of Lake Dianchi Watershed. Three sampling stations were selected along Baoxiang River for observing the flow rate and pollutant concentrations of the first three storm events from June 2009 to August 2009. Net discharged volume, net discharged loading, and net event mean concentration (EMC(n)) were proposed with their calculation methods. According to the analysis of three storm events at three stations, the following results colcd be extracted: (1) the larger the percent of impervious land and population density were, the higher EMC(n) of TSS, TN, TP, permanganate index and their cumulative curves [M(V)] were along the river; (2) TSS, TP loadings as well as their M (V) were positively correlated to the storm intensity, while TN and permanganate index loadings were consistent with the total rainfall of each storm event, where the percent of NO3(-) -N in total nitrogen decreased gradually when the number of storm events increased; (3) compared to tradition EMC, EMC(n) was proven to be a better indicator to accurately uncover and magnify the differences in first flush effects of storm events among different stations or storm events.

Comparison of the treatment performance of hybrid constructed wetlands treating stormwater runoff.

PubMed

Choi, J Y; Maniquiz-Redillas, M C; Hong, J S; Lee, S Y; Kim, L H

2015-01-01

This study was conducted to compare the treatment performance of two hybrid constructed wetlands (CWs) in treating stormwater runoff. The hybrid CWs were composed of a combination of free water surface (FWS) and horizontal subsurface flow (HSSF) CWs. Based on the results, strong correlation exists between potential runoff impacts and stormwater characteristics; however, the low correlations also suggest that not only the monitored parameters contribute to stormwater event mean concentrations (EMC) of pollutants, but other factors should also be considered as well. In the hydraulic and treatment performance of the hybrid CWs, a small surface area to catchment area (SA/CA) ratio, receiving a high concentration of influent EMC, will find it hard to achieve great removal efficiency; also a large SA/CA ratio, receiving low concentration of influent EMC, will find it hard to achieve great removal efficiency. With this, SA/CA ratio and influent characteristics such as EMC or load should be considered among the design factors of CWs. The performance data of the two CWs were used to consider the most cost-effective design of a hybrid CW. The optimum facility capacity (ratio of total runoff volume to storage volume) that is applicable for a target volume reduction and removal efficiency was provided in this study.

Influences of rainfall variables and antecedent discharge on urban effluent concentrations and loads in wet weather.

PubMed

Xu, Zuxin; Xiong, Lijun; Li, Huaizheng; Liao, Zhengliang; Yin, Hailong; Wu, Jun; Xu, Jin; Chen, Hao

2017-04-01

For storm drainages inappropriately connected with sewage, wet weather discharge is a major factor that adversely affects receiving waters. A study of the wet weather influences of rainfall-discharge variables on storm drainages connected with sewage was conducted in the downtown Shanghai area (374 ha). Two indicators, event mean concentration (EMC) and event pollutant load per unit area (EPL), were used to describe the pollution discharge during 20 rain events. The study showed that the total rainfall and discharge volume were important factors that affect the EMCs and EPLs of the chemical oxygen demand, total phosphorus, and especially those of NH 4 + -N. The pollutant concentrations at the beginning of the discharge and the discharge period were also major factors that influence the EMCs of these three pollutants. Regression relationships between the rainfall-discharge variables and discharge volume/ EPLs (R 2 = 0.824-0.981) were stronger than the relationships between the rainfall-discharge variables and EMCs. These regression equations can be considered reliable in the system, with a relative validation error of less than ±10% for the discharge volume, and less than ±20% for the EPLs. The results presented in this paper provide guidance for effectively controlling pollution in similar storm drainages.

Electromagnetic Compatibility of Devices on Hybrid Electromagnetic Components

NASA Astrophysics Data System (ADS)

Konesev, S. G.; Khazieva, R. T.; Kirillov, R. V.; Gainutdinov, I. Z.; Kondratyev, E. Y.

2018-01-01

There is a general tendency to reduce the weight and dimensions, the consumption of conductive and electrical insulating materials, increase the reliability and energy efficiency of electrical devices. In recent years, designers have been actively developing devices based on hybrid electromagnetic components (HEMC) such as inductive-capacitive converters (ICC), voltages pulse generators (VPG), secondary power supplies (SPS), capacitive storage devices (CSD), induction heating systems (IHS). Sources of power supplies of similar electrical devices contain, as a rule, links of increased frequency and function in key (pulse) modes, which leads to an increase in electromagnetic interference (EMI). Nonlinear and periodic (impulse) loads, non-sinusoidal (pulsation) of the electromotive force and nonlinearity of the internal parameters of the source and input circuits of consumers distort the shape of the input voltage lead to an increase in thermal losses from the higher harmonic currents, aging of the insulation, increase in the weight of the power supply filter units, resonance at higher harmonics. The most important task is to analyze the operation of electrotechnical devices based on HEMC from the point of view of creating EMIs and assessing their electromagnetic compatibility (EMC) with power supply systems (PSS). The article presents the results of research on the operation of an IHS, the operation principle of a secondary power supply source of which is based on the operation of a half-bridge autonomous inverter, the switching circuit of which is made in the form of a HEMC, called the «multifunctional integrated electromagnetic component»" (MIEC).

Shuttle orbiter S-band communications equipment design evaluation

NASA Technical Reports Server (NTRS)

Springett, J. C.

1979-01-01

An assessment of S-band communication equipment includes: (1) the review and analysis of the ability of the various subsystem avionic equipment designs to interface with, and operate on signals from/to adjoining equipment; (2) the performance peculiarities of the hardware against the overall specified system requirements; and (3) the evaluation of EMC EMI test results of the various equipment with respect to the possibility of mutual interferences.

The Forward Endcap of the Electromagnetic Calorimeter for the PANDA Detector at FAIR

NASA Astrophysics Data System (ADS)

Albrecht, Malte; PANDA Collaboration

2015-02-01

The versatile 4π-detector PANDA will be built at the Facility for Antiproton and Ion Research (FAIR), an accelerator complex, currently under construction near Darmstadt, Germany. A cooled antiproton beam in a momentum range of 1.5 - 15GeV/c will be provided by the High Energy Storage Ring (HESR). All measurements at PANDA rely on an excellent performance of the detector with respect to tracking, particle identification and energy measurement. The electromagnetic calorimeter (EMC) of the PANDA detector will be equipped with 15744 PbWO4 crystals (PWO-II), which will be operated at a temperature of - 25° C in order to increase the light output. The design of the forward endcap of the EMC has been finalized. The crystals will be read out with Large Area Avalanche Photo Diodes (LAAPDs) in the outer regions and with Vacuum Photo Tetrodes (VPTTs) in the innermost part. Production of photosensor units utilizing charge integrating preamplifiers has begun. A prototype comprised of 216 PbWO4 crystals has been built and tested at various accelerators (CERN SPS, ELSA/Bonn, MAMI/Mainz), where the crystals have been exposed to electron and photon beams of 25MeV up to 15GeV. The results of these test measurements regarding the energy and position resolution are presented.

Nonlinear System Analysis in Bipolar Integrated Circuits.

DTIC Science & Technology

1980-01-01

H2 (fl,f 6), H2 (f2,f4), and H2 (f3,f4) are all equal, Equation (7-8) can be written as v M(t) = mA2 H2 (fl’-f 2) cos[27(f ,-f2)t] (7-9) The AF...and R. A. AMADORI: Micro- wave Interference Effect in Bipolar Transistors, IEEE Trans. EMC, Vol. EMC-17, pp. 216-219, November 1975. 55. KAPLAN , G

Characterization of Stormwater Runoff from a Light Rail Transit Area.

PubMed

Sajjad, Raja Umer; Kim, Kyoung Jin; Memon, Sheeraz; Sukhbaatar, Chinzorig; Paule, Ma Cristina; Lee, Bum-Yeon; Lee, Chang-Hee

2015-09-01

The monitoring of stormwater runoff from Light Rail Transit (LRT) facilities is insufficient in many regions around the world. In this study, runoff quality and quantity were monitored during operational and non-operational LRT phases during 2010-2013. The event mean concentration (EMC) of pollutants showed little statistical variability during both phases. The antecedent dry day (ADD) showed a strong to moderate positive correlation with most pollutant EMCs during the non-operational phase. The existence and magnitude of the first flush from LRT runoff was found to be similar to those from other transportation land uses. The comparison of LRT runoff data with an adjacent road bridge site showed that the pollutant EMC and unit load were 2 to 9 times higher from the road bridge. It was suggested that LRT automated operation and the elevated track makes this transportation mode a viable option for the management of non-point source pollution.

Suppression of Type-II Diabetes with Dyslipidemia and Nephropathy by Peels of Musa cavendish Fruit.

PubMed

Navghare, Vijay; Dhawale, Shashikant

2016-10-01

Musa cavendish, peels has local and traditional use to promote wound healing, hyperglycemia, ulceration etc. The present work investigated the lipid lowering; nephroprotective and glucose lowering properties of ethanolic extract of peels of Musa cavendish (EMC) in alloxan-induced diabetic rats. The EMC 250, 500 and 1000 mg/kg/day and the vehicle were administered orally to alloxan-induced diabetic rats (n = 6) for 3 weeks. Changes in plasma glucose, lipid profile along with kidney function before and after treatment with EMC were recorded. The ethanolic extract of peels of Musa cavendish reduced blood glucose, serum triglyceride, cholesterol, LDL cholesterol and creatinine levels and improvement in body weight, liver glycogen, serum HDL cholesterol, serum albumin and total protein level when compared with untreated rats. Musa cavendish has lipid lowering, nephroprotective and antidiabetic property by regulating glucose uptake in the liver and muscles by restoring the intracellular energy balance.

Entry, Descent, and Landing Performance for a Mid-Lift-to-Drag Ratio Vehicle at Mars

NASA Technical Reports Server (NTRS)

Johnson, Breanna J.; Braden, Ellen M.; Sostaric, Ronald R.; Cerimele, Christopher J.; Lu, Ping

2018-01-01

In an effort to mature the design of the Mid-Lift-to-Drag ratio Rigid Vehicle (MRV) candidate of the NASA Evolvable Mars Campaign (EMC) architecture study, end-to-end six-degree-of-freedom (6DOF) simulations are needed to ensure a successful entry, descent, and landing (EDL) design. The EMC study is assessing different vehicle and mission architectures to determine which candidate would be best to deliver a 20 metric ton payload to the surface of Mars. Due to the large mass payload and the relatively low atmospheric density of Mars, all candidates of the EMC study propose to use Supersonic Retro-Propulsion (SRP) throughout the descent and landing phase, as opposed to parachutes, in order to decelerate to a subsonic touchdown. This paper presents a 6DOF entry-to-landing performance and controllability study with sensitivities to dispersions, particularly in the powered descent and landing phases.

Plant Stem and Leaf Movements in Microgravity. Preliminary Results from a Study Using the EMCS Hardware on the ISS

NASA Astrophysics Data System (ADS)

Johnsson, Anders; Bokn Solheim, Bjarte Gees; Henning Iversen, Tor

2008-06-01

In the 72 days long MULTIGEN-1 experiment movements of Arabidopsis thaliana were recorded using the European Modular Cultivation System, EMCS. One main goal in the experiment was to study possible oscillatory movements of plant parts in weightlessness and under acceleration pulses on centrifuge rotors. Recording was made by video sampling of the plants in cultivation chambers every 5 min. The camera + mirror set-up in the EMCS was developed by alternating the mirror positions to get 'stereoscopic' 2D pictures so that 3D-movements could be constructed. Studies of rhythmic, helical movements of shoots as well as of rhythmic movements of leaves are discussed. It is concluded that gravity amplifies self-sustained circumnutations. Also gravitropical reactions of leaves were successfully documented. The results are of importance, for example in the discussion since Charles Darwin's days on the influence of gravity on circumnutations.

Analysis of waveguides containing EMCs (electromagnetic conductors) or PEMCs (perfect electromagnetic conductors)

NASA Astrophysics Data System (ADS)

Prudêncio, Filipa R.; Matos, Sérgio A.; Paiva, Carlos R.

2014-11-01

The concept of a perfect electromagnetic conductor (PEMC) was introduced to generalize and unify two well-known and apparently disjoint concepts in electromagnetics: the perfect electric conductor (PEC) and the perfect magnetic conductor (PMC). Although the PEMC has proven a fertile tool in electromagnetic analyses dealing with new and complex boundaries, its corresponding definition as a medium has, nevertheless, raised several problems. In fact, according to its initial 3D definition, the PEMC cannot be considered a unique and well-defined medium: it leads to extraneous fields without physical meaning. By using a previously published generalization of a PEMC that regards this concept both as a boundary and as a medium - which was dubbed an MIM (Minkowskian isotropic medium) and acts, in practice, as an actual electromagnetic conductor (EMC) - it is herein presented a straightforward analysis of waveguides containing PEMCs that readily and systematically follows from the general framework of waveguides containing EMCs.

Spin dependent structure function g1 of the deuteron and the proton

NASA Astrophysics Data System (ADS)

Klostermann, L.

1995-05-01

This thesis presents a study on the spin structure of the nucleon, via deep inelastic scattering (DIS) of polarized muons on polarized proton and deuterium targets. The work was done in the Spin Muon Collaboration (SMC) at CERN in Geneva. From the asymmetry in the scattering cross section for nucleon and lepton spins parallel and anti-parallel, one can determine the spin dependent structure function g(sub 1), which contains information on the quark and gluon spin distribution functions. The interpretation in the frame work of the quark parton model (QPM) of earlier results on g(sub 1, sup d) by the European Muon Collaboration (EMC), gave an indication that only a small fraction of the proton spin, compatible with zero, is carried by the spins of the constituent quarks. The SMC was set up to check this unexpected result with improved accuracy, and to combine measurements of g(sub 1, sup p) and g(sub 1, sup d) to test a fundamental sum rule in quantum chromodynamics (QCD), the Bjorken sum rule. The SMC results presented in this thesis are based on data taken in 1992 using a polarized deuterium target and polarized muons with an incident energy of 100 GeV, and 1993 data with a proton target and an incident muon energy of 190 GeV. Using all available data, the fundamental Bjorken sum rule has now been verified at the one standard deviation level to within 16% of its theoretical value.

Results of sub-analysis of a phase 2 study on trabectedin treatment for extraskeletal myxoid chondrosarcoma and mesenchymal chondrosarcoma.

PubMed

Morioka, Hideo; Takahashi, Shunji; Araki, Nobuhito; Sugiura, Hideshi; Ueda, Takafumi; Takahashi, Mitsuru; Yonemoto, Tsukasa; Hiraga, Hiroaki; Hiruma, Toru; Kunisada, Toshiyuki; Matsumine, Akihiko; Susa, Michiro; Nakayama, Robert; Nishimoto, Kazumasa; Kikuta, Kazutaka; Horiuchi, Keisuke; Kawai, Akira

2016-07-14

Trabectedin is reported to be particularly effective against translocation-related sarcoma. Recently, a randomized phase 2 study in patients with translocation-related sarcomas unresponsive or intolerable to standard chemotherapy was conducted, which showed clinical benefit of trabectedin compared with best supportive care (BSC). Extraskeletal myxoid chondrosarcoma (EMCS) and Mesenchymal chondrosarcoma (MCS) are very rare malignant soft tissue sarcomas, and are associated with translocations resulting in fusion genes. In addition, the previous in vivo data showed that trabectedin affect tumor necrosis and reduction in vascularization in a xenograft model of a human high-grade chondrosarcoma. The aim of the present analysis was to clarify the efficacy of trabectedin for EMCS and MCS subjects in the randomized phase 2 study. Five subjects with EMCS and MCS received trabectedin treatment in the randomized phase 2 study. Three MCS subjects were allocated to the BSC group. Objective response and progression-free survival (PFS) were assessed according to the Response Evaluation Criteria in Solid Tumors (RECIST) version 1.1 by central radiology imaging review. The median follow-up time of the randomized phase 2 study was 22.7 months, and one subject with MCS was still receiving trabectedin treatment at the final data cutoff. The median PFS was 12.5 months (95 % CI: 7.4-not reached) in the trabectedin group, while 1.0 months (95 % CI: 0.3-1.0 months) in MCS subjects of the BSC group. The six-month progression-free rate was 100 % in the trabectedin group. One subject with MCS showed partial response, and the others in the trabectedin group showed stable disease. Overall survival of EMCS and MCS subjects was 26.4 months (range, 10.4-26.4 months) in the trabectedin group. At the final data cutoff, two of five subjects were still alive. This sub-analysis shows that trabectedin is effective for patients with EMCS and MCS compared with BSC. The efficacy results were better than previously reported data of TRS. These facts suggest that trabectedin become an important choice of treatment for patients with advanced EMCS or MCS who failed or were intolerable to standard chemotherapy. The randomized phase 2 study is registered with the Japan Pharmaceutical Information Center, number JapicCTI-121850 (May 31, 2012).

Effects of organic silicon compounds as additives on charge-discharge cycling efficiencies of lithium in nonaqueous electrolytes for rechargeable lithium cells

NASA Astrophysics Data System (ADS)

Yanagisawa, Ryota; Endo, Hisayuki; Unno, Masafumi; Morimoto, Hideyuki; Tobishima, Shin-ichi

2014-11-01

Influence of mixing organic silicon compounds into 1 M (M: mol L-1) LiPF6-ethylene carbonate (EC)/ethylmethyl carbonate (EMC) (mixing volume ratio = 3:7) mixed solvent electrolytes on charge-discharge cycling efficiencies of lithium metal negative electrodes is examined. As organic silicon compounds, polyether-modified siloxanes with polyethylene oxide chains, chlorotrimethylsilane, tetraethoxysilane, cis-tetra [isobutyl (dimethylsiloxy)] cyclotetrasiloxane and cage-type silsesquioxane are investigated. Charge-discharge cycling tests of lithium are galvanostatically carried out using stainless steel working electrodes. Charge-discharge cycling efficiencies of lithium tend to improve by mixing organic silicon compounds. A cage-type silsesquioxane, octaphenyloctasilsesquioxane (Ph8T8) exhibits the highest cycling efficiency of approximately 80% with small mixing amount of 0.02 M Ph8T8. Mechanism of enhancement of lithium cycling efficiencies by mixing organic silicon compounds is considered to be due to the suppression of excess reduction of LiPF6-EC/EMC by lithium and the growth of surface film on lithium.

Nondestructive determination of the modulus of elasticity of Fraxinus mandschurica using near-infrared spectroscopy

NASA Astrophysics Data System (ADS)

Yu, Huiling; Liang, Hao; Lin, Xue; Zhang, Yizhuo

2018-04-01

A nondestructive methodology is proposed to determine the modulus of elasticity (MOE) of Fraxinus mandschurica samples by using near-infrared (NIR) spectroscopy. The test data consisted of 150 NIR absorption spectra of the wood samples obtained using an NIR spectrometer, with the wavelength range of 900 to 1900 nm. To eliminate the high-frequency noise and the systematic variations on the baseline, Savitzky-Golay convolution combined with standard normal variate and detrending transformation was applied as data pretreated methods. The uninformative variable elimination (UVE), improved by the evolutionary Monte Carlo (EMC) algorithm and successive projections algorithm (SPA) selected three characteristic variables from full 117 variables. The predictive ability of the models was evaluated concerning the root-mean-square error of prediction (RMSEP) and coefficient of determination (Rp2) in the prediction set. In comparison with the predicted results of all the models established in the experiments, UVE-EMC-SPA-LS-SVM presented the best results with the smallest RMSEP of 0.652 and the highest Rp2 of 0.887. Thus, it is feasible to determine the MOE of F. mandschurica using NIR spectroscopy accurately.

Energy Monitoring and Control Systems Operator Training - Recommended Qualifications, Staffing, Job Description, and Training Requirements for EMCS Operators.

DTIC Science & Technology

1982-06-01

start/stop chiller optimization , and demand limiting were added. The system monitors a 7,000 ton chiller plant and controls 74 air handlers. The EMCS does...Modify analog limits. g. Adjust setpoints of selected controllers. h. Select manual or automatic control modes. i. Enable and disable individual points...or event schedules and controller setpoints ; make nonscheduled starts and stops of equipment or disable field panels when required for routine

Analysis and predictive models of stormwater runoff volumes, loads, and pollutant concentrations from watersheds in the Twin Cities metropolitan area, Minnesota, USA.

PubMed

Brezonik, Patrick L; Stadelmann, Teresa H

2002-04-01

Urban nonpoint source pollution is a significant contributor to water quality degradation. Watershed planners need to be able to estimate nonpoint source loads to lakes and streams if they are to plan effective management strategies. To meet this need for the twin cities metropolitan area, a large database of urban and suburban runoff data was compiled. Stormwater runoff loads and concentrations of 10 common constituents (six N and P forms, TSS, VSS, COD, Pb) were characterized, and effects of season and land use were analyzed. Relationships between runoff variables and storm and watershed characteristics were examined. The best regression equation to predict runoff volume for rain events was based on rainfall amount, drainage area, and percent impervious area (R2 = 0.78). Median event-mean concentrations (EMCs) tended to be higher in snowmelt runoff than in rainfall runoff, and significant seasonal differences were found in yields (kg/ha) and EMCs for most constituents. Simple correlations between explanatory variables and stormwater loads and EMCs were weak. Rainfall amount and intensity and drainage area were the most important variables in multiple linear regression models to predict event loads, but uncertainty was high in models developed with the pooled data set. The most accurate models for EMCs generally were found when sites were grouped according to common land use and size.

Primary epithelial-myoepithelial carcinoma of the lung: A case report demonstrating high-grade transformation-like changes.

PubMed

Tajima, Shogo; Aki, Michihiko; Yajima, Kiyoshige; Takahashi, Tsuyoshi; Neyatani, Hiroshi; Koda, Kenji

2015-07-01

Primary salivary gland-type tumors of the lung are rare; among them, epithelial-myoepithelial carcinomas (EMC) represent a minor histological subtype. The present case documents an EMC that occluded the B8 segment of the left lung in a 72-year-old woman. Macroscopically, the tumor was well-demarcated; however, microscopic examination demonstrated that it had infiltrated the lung parenchyma. The majority of the tumor mass was composed of a myoepithelial overgrowth in conjunction with conventional bilayered ductal structures comprising epithelial and myoepithelial cells. At the advancing edge of the tumor, the myoepithelial overgrowth was observed to be gradually transitioning to a higher-grade component, which demonstrated venous invasion. The Ki-67 labeling index was reduced compared with high-grade transformation (HGT) of salivary gland EMC; p53 was sparsely observed on immunostaining. However, cyclin D1, which is reported to be overexpressed in certain subtypes of salivary gland carcinomas with HGT, was overexpressed in the higher-grade component of the tumor, indicating a potential HGT initiation. The surgical margin was tumor free, and no recurrence has been observed for 4 months. A thorough follow-up is required considering the HGT-like changes and venous invasion of the tumor. Additional studies are required to elucidate the characteristics of pulmonary EMC, with an emphasis on detecting HGT or HGT-like changes.

Evolutionary modification of mesenchyme cells in sand dollars in the transition from indirect to direct development.

PubMed

Yajima, Mamiko

2007-01-01

Peronella japonica, an intermediate type of direct-developing sand dollar, forms an abbreviated pluteus, followed by metamorphosis within 3 days without feeding. In this species, ingression of mesenchyme cells starts before hatching and continues until gastrulation, but no typical secondary mesenchyme cells (SMCs) migrate from the tip of the archenteron. Here, I investigated the cell lineage of mesenchyme cells through metamorphosis in P. japonica and found that mesenchyme cells migrating before hatching (early mesenchyme cells [EMCs]) were exclusively derived from micromeres and became larval skeletogenic cells, whereas cells migrating after hatching (late mesenchyme cells [LMCs]) appeared to contain several nonskeletogenic cells. Thus, it is likely that EMCs are homologous to primary mesenchyme cells (PMCs) and LMCs are similar to the SMCs of typical indirect developers, suggesting that heterochrony in the timing of mesenchyme cell ingression may have occurred in this species. EMCs disappeared after metamorphosis and LMCs were involved in adult skeletogenesis. Embryos from which micromeres were removed at the 16-cell stage formed armless plutei that went on to form adult skeletons and resulted in juveniles with normal morphology. These results suggest that in P. japonica, LMCs form adult skeletal elements, whereas EMCs are specialized for larval spicule formation. The occurrence of evolutionary modifications in mesenchyme cells in the transition from indirect to direct development of sand dollars is discussed.

Managing for the next big thing. Interview by Paul Hemp.

PubMed

Ruettgers, M

2001-01-01

In this HBR interview, CEO Michael Ruettgers speaks in detail about the managerial practices that have allowed EMC to anticipate and exploit disruptive technologies, market opportunities, and business models ahead of its competitors. He recounts how the company repeatedly ventured into untested markets, ultimately transforming itself from a struggling maker of minicomputer memory boards into a data storage powerhouse and one of the most successful companies of the past decade. The company has achieved sustained and nearly unrivaled revenue, profit, and shareprice growth through a number of means. Emphasizing timing and speed, Ruettgers says, is critical. That's meant staggering products rather than developing them sequentially and avoiding the excessive refinements that slow time to market. Indeed, a sense of urgency, Ruettgers explains, has been critical to EMC's success. Processes such as quarterly goal setting and monthly forecasting meetings help maintain a sense of urgency and allow managers to get early glimpses of changes in the market. So does an environment in which personal accountability is stressed and the corporate focus is single-minded. Perhaps most important, the company has procedures to glean insights from customers. Intensive forums involving EMC engineers and leading-edge customers, who typically push for unconventional solutions to their problems, often yield new product features. Similarly, a customer service system that includes real-time monitoring of product use enables EMC to understand customer needs firsthand.

Clinicopathologic and radiologic features of extraskeletal myxoid chondrosarcoma: a retrospective study of 40 Chinese cases with literature review.

PubMed

Shao, Rui; Lao, I Weng; Wang, Lei; Yu, Lin; Wang, Jian; Fan, Qinhe

2016-08-01

The aim of this study is to describe the clinicopathologic and radiologic features of 40 cases of extraskeletal myxoid chondrosarcoma (EMC) from China. There were 25 males and 15 females (sex ratio, 1.7:1). Apart from an adolescent, all patients were adults with a median age of 49years. Twenty-four tumors (60%) occurred in the lower limb and limb girdles, especially the thigh, followed by the upper limb and limb girdles (20%) and trunk (10%). Other less commonly involved locations included the head and neck, sacrococcygeal region, and perineum. Tumors ranged in size from 1.5 to 19cm (mean, 7cm). By radiology, they appeared as hypoattenuated or isoattenuated masses on computed tomography with hyperintense signal on T2-weighted magnetic resonance imaging. Intralesional hypointense septa were present in most cases. Of the 40 tumors, 30 belonged to the classic subtype, whereas 9 cases were cellular, and 1 case had a rhabdoid phenotype. Tumor cells showed variable expression of synaptophysin (36%), S-100 protein (29%), epithelial membrane antigen (11%), and neuron-specific enolase (7%). Ki-67 index was remarkably higher in the cellular variant (mean, 30%). EWSR1-related rearrangement was detected in 12 of 14 cases tested by fluorescence in situ hybridization using break-apart probes. The overall 5- and 7-year survival was 71% and 60%, respectively. Awareness of the imaging features may help pathologists in the diagnosis of EMC. Fluorescence in situ hybridization also serves as a useful diagnostic tool for EMC, especially in the distinction from its mimics. Copyright © 2016 Elsevier Inc. All rights reserved.

[Total pollution features of urban runoff outlet for urban river].

PubMed

Luo, Hong-Bing; Luo, Lin; Huang, Gu; He, Qiang; Liu, Ping

2009-11-01

The urban stormwater runoff discharged to urban river, especially to rainfall source river, cannot be ignored. In this study, the Futian River watershed in Shenzhen city in a typical southern city of China is taken as the research object. In order to guide the pollution control for urban river, the eighteen rainfall events were monitored, and the total pollution features of the urban runoff outlet for this urban river were analyzed and discussed by using the process of pollutographs, the identifying to first flush, event mean concentration (EMC), etc. Results show that the concentrations of COD, SS, TN, TP and BOD5 are ten times more than the grade V of the environmental quality standards for surface water during the runoff time; the pollution caused by heavy metals (Cr, Ge, Cu, Hg and As) in runoff at a typical rainfall event is serious; the average and range of pollutant concentration at this runoff outlet in study area are evidently higher than at Shapingba in Chongqing city of China and at Silerwood in Canada, but are lower than at Shilipu in Wuhan city of China. The first flushes of COD, SS, BOD5, especially COD and SS, are evident, but the TN and TP are not. The average EMC of COD, TN, TP and BOD5 are 224.14, 571.15, 5.223, 2.04, 143.5 mg/L, respectively. To some extent, the EMC of COD is about two times of the value of the near cities, Macao and Zhuhai. The EMC of TN and TP are obviously higher than Beijing, Guangzhou and Shanghai. To compared with foreign counties, the EMC of the study area in Shenzhen is obviously much higher than the cities of Korean, USA and Canada. So the total pollution caused by the urban surface runoff in study area is serious and necessary to be treated.

Vehicle Fault Diagnose Based on Smart Sensor

NASA Astrophysics Data System (ADS)

Zhining, Li; Peng, Wang; Jianmin, Mei; Jianwei, Li; Fei, Teng

In the vehicle's traditional fault diagnose system, we usually use a computer system with a A/D card and with many sensors connected to it. The disadvantage of this system is that these sensor can hardly be shared with control system and other systems, there are too many connect lines and the electro magnetic compatibility(EMC) will be affected. In this paper, smart speed sensor, smart acoustic press sensor, smart oil press sensor, smart acceleration sensor and smart order tracking sensor were designed to solve this problem. With the CAN BUS these smart sensors, fault diagnose computer and other computer could be connected together to establish a network system which can monitor and control the vehicle's diesel and other system without any duplicate sensor. The hard and soft ware of the smart sensor system was introduced, the oil press, vibration and acoustic signal are resampled by constant angle increment to eliminate the influence of the rotate speed. After the resample, the signal in every working cycle could be averaged in angle domain and do other analysis like order spectrum.

Nonlinear system analysis in bipolar integrated circuits

NASA Astrophysics Data System (ADS)

Fang, T. F.; Whalen, J. J.

1980-01-01

Since analog bipolar integrated circuits (IC's) have become important components in modern communication systems, the study of the Radio Frequency Interference (RFI) effects in bipolar IC amplifiers is an important subject for electromagnetic compatibility (EMC) engineering. The investigation has focused on using the nonlinear circuit analysis program (NCAP) to predict RF demodulation effects in broadband bipolar IC amplifiers. The audio frequency (AF) voltage at the IC amplifier output terminal caused by an amplitude modulated (AM) RF signal at the IC amplifier input terminal was calculated and compared to measured values. Two broadband IC amplifiers were investigated: (1) a cascode circuit using a CA3026 dual differential pair; (2) a unity gain voltage follower circuit using a micro A741 operational amplifier (op amp). Before using NCAP for RFI analysis, the model parameters for each bipolar junction transistor (BJT) in the integrated circuit were determined. Probe measurement techniques, manufacturer's data, and other researcher's data were used to obtain the required NCAP BJT model parameter values. An important contribution included in this effort is a complete set of NCAP BJT model parameters for most of the transistor types used in linear IC's.

Space processing applications payload equipment study. Volume 2B: Payload interface analysis (power/thermal/electromagnetic compatibility)

NASA Technical Reports Server (NTRS)

Hammel, R. L. (Editor); Smith, A. G. (Editor)

1974-01-01

As a part of the task of performing preliminary engineering analysis of modular payload subelement/host vehicle interfaces, a subsystem interface analysis was performed to establish the integrity of the modular approach to the equipment design and integration. Salient areas that were selected for analysis were power and power conditioning, heat rejection and electromagnetic capability (EMC). The equipment and load profiles for twelve representative experiments were identified. Two of the twelve experiments were chosen as being representative of the group and have been described in greater detail to illustrate the evaluations used in the analysis. The shuttle orbiter will provide electrical power from its three fuel cells in support of the orbiter and the Spacelab operations. One of the three shuttle orbiter fuel cells will be dedicated to the Spacelab electrical power requirements during normal shuttle operation. This power supplies the Spacelab subsystems and the excess will be available to the payload. The current Spacelab sybsystem requirements result in a payload allocation of 4.0 to 4.8 kW average (24 hour/day) and 9.0 kW peak for 15 minutes.

Highway runoff quality models for the protection of environmentally sensitive areas

NASA Astrophysics Data System (ADS)

Trenouth, William R.; Gharabaghi, Bahram

2016-11-01

This paper presents novel highway runoff quality models using artificial neural networks (ANN) which take into account site-specific highway traffic and seasonal storm event meteorological factors to predict the event mean concentration (EMC) statistics and mean daily unit area load (MDUAL) statistics of common highway pollutants for the design of roadside ditch treatment systems (RDTS) to protect sensitive receiving environs. A dataset of 940 monitored highway runoff events from fourteen sites located in five countries (Canada, USA, Australia, New Zealand, and China) was compiled and used to develop ANN models for the prediction of highway runoff suspended solids (TSS) seasonal EMC statistical distribution parameters, as well as the MDUAL statistics for four different heavy metal species (Cu, Zn, Cr and Pb). TSS EMCs are needed to estimate the minimum required removal efficiency of the RDTS needed in order to improve highway runoff quality to meet applicable standards and MDUALs are needed to calculate the minimum required capacity of the RDTS to ensure performance longevity.

Shadows of rotating five-dimensional charged EMCS black holes

NASA Astrophysics Data System (ADS)

Amir, Muhammed; Singh, Balendra Pratap; Ghosh, Sushant G.

2018-05-01

Higher-dimensional theories admit astrophysical objects like supermassive black holes, which are rather different from standard ones, and their gravitational lensing features deviate from general relativity. It is well known that a black hole shadow is a dark region due to the falling geodesics of photons into the black hole and, if detected, a black hole shadow could be used to determine which theory of gravity is consistent with observations. Measurements of the shadow sizes around the black holes can help to evaluate various parameters of the black hole metric. We study the shapes of the shadow cast by the rotating five-dimensional charged Einstein-Maxwell-Chern-Simons (EMCS) black holes, which is characterized by four parameters, i.e., mass, two spins, and charge, in which the spin parameters are set equal. We integrate the null geodesic equations and derive an analytical formula for the shadow of the five-dimensional EMCS black hole, in turn, to show that size of black hole shadow is affected due to charge as well as spin. The shadow is a dark zone covered by a deformed circle, and the size of the shadow decreases with an increase in the charge q when compared with the five-dimensional Myers-Perry black hole. Interestingly, the distortion increases with charge q. The effect of these parameters on the shape and size of the naked singularity shadow of the five-dimensional EMCS black hole is also discussed.

General Environmental Verification Specification

NASA Technical Reports Server (NTRS)

Milne, J. Scott, Jr.; Kaufman, Daniel S.

2003-01-01

The NASA Goddard Space Flight Center s General Environmental Verification Specification (GEVS) for STS and ELV Payloads, Subsystems, and Components is currently being revised based on lessons learned from GSFC engineering and flight assurance. The GEVS has been used by Goddard flight projects for the past 17 years as a baseline from which to tailor their environmental test programs. A summary of the requirements and updates are presented along with the rationale behind the changes. The major test areas covered by the GEVS include mechanical, thermal, and EMC, as well as more general requirements for planning, tracking of the verification programs.

Development of dual sensor hand-held detector

NASA Astrophysics Data System (ADS)

Sezgin, Mehmet

2010-04-01

In this paper hand-held dual sensor detector development requirements are considered dedicated to buried object detection. Design characteristics of such a system are categorized and listed. Hardware and software structures, ergonomics, user interface, environmental and EMC/EMI tests to be applied and performance test issues are studied. Main properties of the developed system (SEZER) are presented, which contains Metal Detector (MD) and Ground Penetrating Radar (GPR). The realized system has ergonomic structure and can detect both metallic and non-metallic buried objects. Moreover classification of target is possible if it was defined to the signal processing software in learning phase.

[Magnetic resonance compatibility research for coronary mental stents].

PubMed

Wang, Ying; Liu, Li; Wang, Shuo; Shang, Ruyao; Wang, Chunren

2015-01-01

The objective of this article is to research magnetic resonance compatibility for coronary mental stents, and to evaluate the magnetic resonance compatibility based on laboratory testing results. Coronary stents magnetic resonance compatibility test includes magnetically induced displacement force test, magnetically induced torque test, radio frequency induced heating and evaluation of MR image. By magnetic displacement force and torque values, temperature, and image distortion values to determine metal coronary stent demagnetization effect. The methods can be applied to test magnetic resonance compatibility for coronary mental stents and evaluate its demagnetization effect.

EMC effect: Past, Present, and Future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fomin, Nadia

2015-09-01

Since the discovery of the EMC effect over 30 years ago, it has been of great theoretical interest and studied in several experimental measurements. No unified picture arose to explain the underlying cause of per nucleon structure function modification in nuclei. Precise measurements on light nuclei from JLab’s 6 GeV era revitalized this research by showing that traditional A or density dependent models of this nuclear modification do not work. The measurements will be reviewed, discussed and preliminary data on heavy targets from JLab’s E03-103 will be presented.

On the deduction of chemical reaction pathways from measurements of time series of concentrations.

PubMed

Samoilov, Michael; Arkin, Adam; Ross, John

2001-03-01

We discuss the deduction of reaction pathways in complex chemical systems from measurements of time series of chemical concentrations of reacting species. First we review a technique called correlation metric construction (CMC) and show the construction of a reaction pathway from measurements on a part of glycolysis. Then we present two new improved methods for the analysis of time series of concentrations, entropy metric construction (EMC), and entropy reduction method (ERM), and illustrate (EMC) with calculations on a model reaction system. (c) 2001 American Institute of Physics.

Electrochemical Performance of LiNi0.5Mn1.5O4 by Sol-gel Self-combustion Reaction Method in Different Kinds of Electrolyte for High-voltage Rechargeable Lithium Cells

NASA Astrophysics Data System (ADS)

Liang, Xinghua; Shi, Lin; Liu, Yusi; Zeng, Shuaibo; Ye, Chaochao

2015-07-01

LiNi0.5Mn1.5O4 cathode material was synthesized through sol-gel self-combustion reaction method. LiNi0.5Mn1.5O4 powders were subsequently characterized as cathode materials in a Li-ion coin cell comprising a Li anode with electrolyte A or electrolyte B. 1.0 mol/L Lithium Hexafluorophosphate (LiPF6) dissolved in volume ration of ethylene carbonate (EC) to ethyl methyl carbonate (EMC) to diethyl carbonate (DEC) corresponded to 4:3:3as electrolyte A, 1.0 mol/L LiPF6 dissolved in volume ration of EC to EMC to DEC corresponded to 4:2:4 as electrolyte B. Electrochemical performance of lithium cells was evaluated. These tests showed that no matter the cells with electrolyte A or electrolyte B has good discharge platform in 4.7V range (3.5V-4.75V) at the rate of 0.1C, the initial discharge capacity of cell with electrolyte B was higher than that with electrolyte A.

Small Habitat Commonality Reduces Cost for Human Mars Missions

NASA Technical Reports Server (NTRS)

Griffin, Brand N.; Lepsch, Roger; Martin, John; Howard, Robert; Rucker, Michelle; Zapata, Edgar; McCleskey, Carey; Howe, Scott; Mary, Natalie; Nerren, Philip (Inventor)

2015-01-01

Most view the Apollo Program as expensive. It was. But, a human mission to Mars will be orders of magnitude more difficult and costly. Recently, NASA's Evolvable Mars Campaign (EMC) mapped out a step-wise approach for exploring Mars and the Mars-moon system. It is early in the planning process but because approximately 80% of the total life cycle cost is committed during preliminary design, there is an effort to emphasize cost reduction methods up front. Amongst the options, commonality across small habitat elements shows promise for consolidating the high bow-wave costs of Design, Development, Test and Evaluation (DDT&E) while still accommodating each end-item's functionality. In addition to DDT&E, there are other cost and operations benefits to commonality such as reduced logistics, simplified infrastructure integration and with inter-operability, improved safety and simplified training. These benefits are not without a cost. Some habitats are sub-optimized giving up unique attributes for the benefit of the overall architecture and because the first item sets the course for those to follow, rapidly developing technology may be excluded. The small habitats within the EMC include the pressurized crew cabins for the ascent vehicle,

22st Annual National Test and Evaluation Conference

DTIC Science & Technology

2006-03-09

B1 B2 y ii) Factor B affects the standard deviation C2 C1 y iii) Factor C affects the average and the standard deviation D1 = D2 y iv) Factor D has...22303 UNITED STATES (P) (703)862-0908 (F) (703)970-5700 poole_grady@emc.com Mr. Josh Pressnell RTI 8306 Rugby Rd. Manassas, VA 20111...Ricciardi RTI 8306 Rugby Rd. Manassas, VA 20111-1912 UNITED STATES (P) (703)365-9662 (F) (703)365-9818 michael.ricciardi@rti-world.com Mr

Different styles of postseismic deformation after the 2013 M7.7 Balochistan earthquake in Pakistan and the 2010 M7.2 El Mayor-Cucapah earthquake in Mexico

NASA Astrophysics Data System (ADS)

Fielding, E. J.; Yague-Martinez, N.; Motagh, M.; Gonzalez-Ortega, J. A.; Huang, M. H.; Burgmann, R.; Freed, A. M.; Samsonov, S. V.

2014-12-01

We study postseismic deformation after the Mw 7.7 earthquake in the Balochistan region of western Pakistan on 24 September 2013 and the Mw 7.2 El Mayor-Cucapah (EMC) earthquake in Baja California of northern Mexico on 4 April 2010. Pakistan InSAR measurements from the German TerraSAR-X (TSX) and Canadian RADARSAT-2 (RS2) satellites include TSX narrow stripmap beams on a descending track, RS2 wide strip modes, and TSX wide-swath ScanSAR images on an ascending track, specially acquired with interferometric alignment of ScanSAR bursts. For the EMC earthquake, InSAR includes Envisat, ALOS, and RS2 satellites and NASA/JPL UAVSAR airborne InSAR, with piece-wise time coverage. Plate Boundary Observatory acquires continuous GPS data and others collect campaign GPS. Interferograms show significant afterslip on both main ruptures in the first weeks and months, not masked by the atmospheric effects. Balochistan shallow afterslip reaches at least 10 cm in 2-4 months in the same area as the largest coseismic slip, but less near the aftershock activity. Rapid afterslip was observed primarily at the ends of the EMC mainshock rupture where the strike changes, with magnitudes up to 30 cm. Large variations of tropospheric water vapor complicate measurement of small long-wavelength deformation so we do time series analysis. We expect viscoelastic relaxation after these two strike-slip earthquakes to differ due to completely opposite tectonic settings: EMC earthquake in the Salton Trough rift and fast-moving strike-slip system, where crust and lithosphere are thin and hot with very shallow asthenosphere, and Balochistan earthquake in the shortening Makran accretional prism with much slower strike-slip deformation rates and cold and thick lithosphere of the subducting Arabian plate directly beneath it, so asthenosphere is much deeper. Studies have found rapid and large viscoelastic relaxation for the EMC quake, but we don't expect measurable relaxation in the Balochistan area in the first year, based on preliminary modeling. These very different lithospheric configurations have strong implications for transfer of stress and future earthquake risk.

Chemorheology of highly filled thermosets: Effects of fillers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Halley, P.J.

1996-12-31

Highly filled thermosets are utilised in the manufacture of many high value added products in the aerospace, communication, computer and automobile industries. A fundamental understanding of the processing of these materials has, however, been hindered by the inherent complexities of the flow and cure properties of these composite thermoset materials. A chemorheological (gel point and chemoviscosity) testing procedure is described here that uses dynamic multiwave tests on a modified Rheometrics RDSII system, using a filled epoxy moulding compound (EMC). Data from this testing procedure has been combined with physical property and kinetic data to produce realistic simulation results using flowmore » simulation software (TSET; MOLDFLOW Pty Ltd). This chemorheological testing procedure has now been successfully implemented commercially by MOLDFLOW Pty Ltd.« less

Use of phosphoranimines to reduce organic carbonate content in Li-ion battery electrolytes

DOE PAGES

Dufek, Eric J.; Klaehn, John R.; McNally, Joshua S.; ...

2016-05-09

In this study, the use of phosphoranimines (PAs), a class of linear, monomeric phosphazenes, as electrolytes for Li-ion battery applications has been investigated as a route to improve safety and stability for Li-ion batteries. Of the potential PAs for use in battery applications, this work focuses on the initial synthetic preparation and analysis of N-trimethylsilyl-P,P-bis((2-methoxyethoxy)ethoxy)-P-ethylphosphoranimine (PA-5). PA-5 has high LiPF6 solubility in excess of 2 M, high thermal stability with a melting point below -80°C and high thermal stability as a neat compound to at least 250°C. As part of electrolyte blends, the inclusion of PA-5 shifts the onset ofmore » thermal degradation by close to 40°C at 35% loading and by 20°C at a 10% loading, improves the low temperature performance of the electrolyte, and when used as a primary solvent leads to increases in the flash point (by 20°C) when compared to more traditional EC:EMC blends. Cycling capabilities of full-coin cells with graphite negative electrodes and Li 1+w[Ni 0.5Mn 0.3Co 0.2] 1-wO 2 positive electrodes using PA-5:EC:EMC electrolyte blends are comparable with the performance seen for traditional EC:EMC blends. Analysis of the impact of the use of additives such as vinylene carbonate in PA-5:EC:EMC blended electrolyte results in enhanced capacity retention and improved coulombic efficiency.« less

EMC effect for light nuclei: New results from Jefferson Lab

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aji Daniel

High energy lepton scattering has been the primary tool for mapping out the quark distributions of nucleons and nuclei. Measurements of deep inelastic scattering in nuclei show that the quark distributions in heavy nuclei are not simply the sum of the quark distributions of the constituent proton and neutron, as one might expect for a weakly bound system. This modification of the quark distributions in nuclei is known as the EMC effect. I will discuss the results from Jefferson Lab (JLab) experiment E03-103, a precise measurement of the EMC effect in few-body nuclei with emphasis on the large x region.more » Data from the light nuclei suggests that the nuclear dependence of the high x quark distribution may depend on the nucleon's local environment, rather than being a purely bulk effect. In addition, I will also discuss about a future experiment at the upgraded 12 GeV Jefferson Lab facility which will further investigate the role of the local nuclear environment and the influence of detailed nuclear structure to the modification of quark distributions.« less

Transport simulations of linear plasma generators with the B2.5-Eirene and EMC3-Eirene codes

DOE PAGES

Rapp, Juergen; Owen, Larry W.; Bonnin, X.; ...

2014-12-20

Linear plasma generators are cost effective facilities to simulate divertor plasma conditions of present and future fusion reactors. For this research, the codes B2.5-Eirene and EMC3-Eirene were extensively used for design studies of the planned Material Plasma Exposure eXperiment (MPEX). Effects on the target plasma of the gas fueling and pumping locations, heating power, device length, magnetic configuration and transport model were studied with B2.5-Eirene. Effects of tilted or vertical targets were calculated with EMC3-Eirene and showed that spreading the incident flux over a larger area leads to lower density, higher temperature and off-axis profile peaking in front of themore » target. In conclusion, the simulations indicate that with sufficient heating power MPEX can reach target plasma conditions that are similar to those expected in the ITER divertor. B2.5-Eirene simulations of the MAGPIE experiment have been carried out in order to establish an additional benchmark with experimental data from a linear device with helicon wave heating.« less

Muscle contraction and the elasticity-mediated crosstalk effect

NASA Astrophysics Data System (ADS)

Dharan, Nadiv; Farago, Oded

2013-05-01

Cooperative action of molecular motors is essential for many cellular processes. One possible regulator of motor coordination is the elasticity-mediated crosstalk (EMC) coupling between myosin II motors whose origin is the tensile stress that they collectively generate in actin filaments. Here, we use a statistical mechanical analysis to investigate the influence of the EMC effect on the sarcomere — the basic contractile unit of skeletal muscles. We demonstrate that the EMC effect leads to an increase in the attachment probability of motors located near the end of the sarcomere while simultaneously decreasing the attachment probability of the motors in the central part. Such a polarized attachment probability would impair the motors' ability to cooperate efficiently. Interestingly, this undesired phenomenon becomes significant only when the system size exceeds that of the sarcomere in skeletal muscles, which provides an explanation for the remarkable lack of sarcomere variability in vertebrates. Another phenomenon that we investigate is the recently observed increase in the duty ratio of the motors with the tension in muscle. We reveal that the celebrated Hill's equation for muscle contraction is very closely related to this observation.

First Search for the EMC Effect and Nuclear Shadowing in Neutrino Nucleus Deep Inelastic Scattering at MINERvA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mousseau, Joel A.

2015-01-01

Decades of research in electron-nucleus deep inelastic scattering (DIS) have provided a clear picture of nuclear physics at high momentum transfer. While these effects have been clearly demonstrated by experiment, the theoretical explanation of their origin in some kinematic regions has been lacking. Particularly, the effects in the intermediate regions of Bjorken-x, anti-shadowing and the EMC effect have no universally accepted quantum mechanical explanation. In addition, these effects have not been measured systematically with neutrino-nucleus deep inelastic scattering, due to experiments lacking multiple heavy targets.

Evaluating performance of stormwater sampling approaches using a dynamic watershed model.

PubMed

Ackerman, Drew; Stein, Eric D; Ritter, Kerry J

2011-09-01

Accurate quantification of stormwater pollutant levels is essential for estimating overall contaminant discharge to receiving waters. Numerous sampling approaches exist that attempt to balance accuracy against the costs associated with the sampling method. This study employs a novel and practical approach of evaluating the accuracy of different stormwater monitoring methodologies using stormflows and constituent concentrations produced by a fully validated continuous simulation watershed model. A major advantage of using a watershed model to simulate pollutant concentrations is that a large number of storms representing a broad range of conditions can be applied in testing the various sampling approaches. Seventy-eight distinct methodologies were evaluated by "virtual samplings" of 166 simulated storms of varying size, intensity and duration, representing 14 years of storms in Ballona Creek near Los Angeles, California. The 78 methods can be grouped into four general strategies: volume-paced compositing, time-paced compositing, pollutograph sampling, and microsampling. The performances of each sampling strategy was evaluated by comparing the (1) median relative error between the virtually sampled and the true modeled event mean concentration (EMC) of each storm (accuracy), (2) median absolute deviation about the median or "MAD" of the relative error or (precision), and (3) the percentage of storms where sampling methods were within 10% of the true EMC (combined measures of accuracy and precision). Finally, costs associated with site setup, sampling, and laboratory analysis were estimated for each method. Pollutograph sampling consistently outperformed the other three methods both in terms of accuracy and precision, but was the most costly method evaluated. Time-paced sampling consistently underestimated while volume-paced sampling over estimated the storm EMCs. Microsampling performance approached that of pollutograph sampling at a substantial cost savings. The most efficient method for routine stormwater monitoring in terms of a balance between performance and cost was volume-paced microsampling, with variable sample pacing to ensure that the entirety of the storm was captured. Pollutograph sampling is recommended if the data are to be used for detailed analysis of runoff dynamics.

SU-F-T-365: Clinical Commissioning of the Monaco Treatment Planning System for the Novalis Tx to Deliver VMAT, SRS and SBRT Treatments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adnani, N

Purpose: To commission the Monaco Treatment Planning System for the Novalis Tx machine. Methods: The commissioning of Monte-Carlo (MC), Collapsed Cone (CC) and electron Monte-Carlo (eMC) beam models was performed through a series of measurements and calculations in medium and in water. In medium measurements relied Octavius 4D QA system with the 1000 SRS detector array for field sizes less than 4 cm × 4 cm and the 1500 detector array for larger field sizes. Heterogeneity corrections were validated using a custom built phantom. Prior to clinical implementation, an end to end testing of a Prostate and H&N VMAT plansmore » was performed. Results: Using a 0.5% uncertainty and 2 mm grid sizes, Tables I and II summarize the MC validation at 6 MV and 18 MV in both medium and water. Tables III and IV show similar comparisons for CC. Using the custom heterogeneity phantom setup of Figure 1 and IGRT guidance summarized in Figure 2, Table V lists the percent pass rate for a 2%, 2 mm gamma criteria at 6 and 18 MV for both MC and CC. The relationship between MC calculations settings of uncertainty and grid size and the gamma passing rate for a prostate and H&N case is shown in Table VI. Table VII lists the results of the eMC calculations compared to measured data for clinically available applicators and Table VIII for small field cutouts. Conclusion: MU calculations using MC are highly sensitive to uncertainty and grid size settings. The difference can be of the order of several per cents. MC is superior to CC for small fields and when using heterogeneity corrections, regardless of field size, making it more suitable for SRS, SBRT and VMAT deliveries. eMC showed good agreement with measurements down to 2 cm − 2 cm field size.« less

Testing cosmology from fundamental considerations: Is the Friedmann universe intrinsically flat

NASA Astrophysics Data System (ADS)

Mitra, Abhas

2014-02-01

Recently Melia and Shevchuk (Mon Not R Astron Soc 419:2579,2012) (MS) have proposed the so-called cosmology where the "Gravitational Horizon" of the universe is equal to the distance travelled by light since "Big Bang". Here we would like to see whether the basic claim is correct or not because MS have not given any cogent derivation for the same. Essentially we will compare the twin expressions for the Einstein energy momentum complex (EMC) of the Friedmann universe obtained by using an appropriate superpotential and also by a direct method. To enable a meaningful comparison of the twin expressions, both are computed by using the same quasi-Cartesian coordinates. We however do not claim that Einstein EMC is superior to many other routes of defining EM of a self-gravitating system. In fact, for static isolated spherical syatems, the idea of a coordinate independent field energy of Lynden-Bell and Katz (Mon Not R Astron Soc 213:21, 1985) might be quite physically significant. Yet, here, we use Einstein EMC because (i) our system is non-static and not isolated one (ii) our primary aim is not find any absolute value of EM, and, finally, (iii) only Einstein pseudo-tensor offers equivalent twin expressions for EM which one can be equated irrespective of any physical significance. Following such comparison of equivalent twin expressions of Einstein energy, we find an exact proof as to why Friedmann universe must be spatially flat even though, mathematically one can conceive of curved spaces in any dimension. Additionally, it follows that, apparently, the scale factor as insisted by proposition. Nonetheless, because of close similarity of this form, , with the (vacuum) Milne metric, and also because of implied unphysical equation of state, cosmology is unlikely to represent the physical universe.

Sensitivity and Specificity of the Coma Recovery Scale--Revised Total Score in Detection of Conscious Awareness.

PubMed

Bodien, Yelena G; Carlowicz, Cecilia A; Chatelle, Camille; Giacino, Joseph T

2016-03-01

To describe the sensitivity and specificity of Coma Recovery Scale-Revised (CRS-R) total scores in detecting conscious awareness. Data were retrospectively extracted from the medical records of patients enrolled in a specialized disorders of consciousness (DOC) program. Sensitivity and specificity analyses were completed using CRS-R-derived diagnoses of minimally conscious state (MCS) or emerged from minimally conscious state (EMCS) as the reference standard for conscious awareness and the total CRS-R score as the test criterion. A receiver operating characteristic curve was constructed to demonstrate the optimal CRS-R total cutoff score for maximizing sensitivity and specificity. Specialized DOC program. Patients enrolled in the DOC program (N=252, 157 men; mean age, 49y; mean time from injury, 48d; traumatic etiology, n=127; nontraumatic etiology, n=125; diagnosis of coma or vegetative state, n=70; diagnosis of MCS or EMCS, n=182). Not applicable. Sensitivity and specificity of CRS-R total scores in detecting conscious awareness. A CRS-R total score of 10 or higher yielded a sensitivity of .78 for correct identification of patients in MCS or EMCS, and a specificity of 1.00 for correct identification of patients who did not meet criteria for either of these diagnoses (ie, were diagnosed with vegetative state or coma). The area under the curve in the receiver operating characteristic curve analysis is .98. A total CRS-R score of 10 or higher provides strong evidence of conscious awareness but resulted in a false-negative diagnostic error in 22% of patients who demonstrated conscious awareness based on CRS-R diagnostic criteria. A cutoff score of 8 provides the best balance between sensitivity and specificity, accurately classifying 93% of cases. The optimal total score cutoff will vary depending on the user's objective. Copyright © 2016 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Test beam demonstration of silicon microstrip modules with transverse momentum discrimination for the future CMS tracking detector

NASA Astrophysics Data System (ADS)

Adam, W.; Bergauer, T.; Brondolin, E.; Dragicevic, M.; Friedl, M.; Frühwirth, R.; Hoch, M.; Hrubec, J.; König, A.; Steininger, H.; Treberspurg, W.; Waltenberger, W.; Alderweireldt, S.; Beaumont, W.; Janssen, X.; Lauwers, J.; Van Mechelen, P.; Van Remortel, N.; Van Spilbeeck, A.; Beghin, D.; Brun, H.; Clerbaux, B.; De Lentdecker, G.; Delannoy, H.; Fasanella, G.; Favart, L.; Goldouzian, R.; Grebenyuk, A.; Karapostoli, G.; Lenzi, T.; Léonard, A.; Luetic, J.; Maerschalk, T.; Marinov, A.; Postiau, N.; Randle-Conde, A.; Seva, T.; Vanlaer, P.; Vannerom, D.; Yonamine, R.; Wang, Q.; Yang, Y.; Zenoni, F.; Zhang, F.; Abu Zeid, S.; Blekman, F.; De Bruyn, I.; De Clercq, J.; D'Hondt, J.; Deroover, K.; Lowette, S.; Moortgat, S.; Moreels, L.; Python, Q.; Skovpen, K.; Van Mulders, P.; Van Parijs, I.; Bakhshiansohi, H.; Bondu, O.; Brochet, S.; Bruno, G.; Caudron, A.; Delaere, C.; Delcourt, M.; De Visscher, S.; Francois, B.; Giammanco, A.; Jafari, A.; Cabrera Jamoulle, J.; De Favereau De Jeneret, J.; Komm, M.; Krintiras, G.; Lemaitre, V.; Magitteri, A.; Mertens, A.; Michotte, D.; Musich, M.; Piotrzkowski, K.; Quertenmont, L.; Szilasi, N.; Vidal Marono, M.; Wertz, S.; Beliy, N.; Caebergs, T.; Daubie, E.; Hammad, G. H.; Härkönen, J.; Lampén, T.; Luukka, P.; Peltola, T.; Tuominen, E.; Tuovinen, E.; Eerola, P.; Baulieu, G.; Boudoul, G.; Caponetto, L.; Combaret, C.; Contardo, D.; Dupasquier, T.; Gallbit, G.; Lumb, N.; Mirabito, L.; Perries, S.; Vander Donckt, M.; Viret, S.; Agram, J.-L.; Andrea, J.; Bloch, D.; Bonnin, C.; Brom, J.-M.; Chabert, E.; Chanon, N.; Charles, L.; Conte, E.; Fontaine, J.-Ch.; Gross, L.; Hosselet, J.; Jansova, M.; Tromson, D.; Autermann, C.; Feld, L.; Karpinski, W.; Kiesel, K. M.; Klein, K.; Lipinski, M.; Ostapchuk, A.; Pierschel, G.; Preuten, M.; Rauch, M.; Schael, S.; Schomakers, C.; Schulz, J.; Schwering, G.; Wlochal, M.; Zhukov, V.; Pistone, C.; Fluegge, G.; Kuensken, A.; Pooth, O.; Stahl, A.; Aldaya, M.; Asawatangtrakuldee, C.; Beernaert, K.; Bertsche, D.; Contreras-Campana, C.; Eckerlin, G.; Eckstein, D.; Eichhorn, T.; Gallo, E.; Garay Garcia, J.; Hansen, K.; Haranko, M.; Harb, A.; Hauk, J.; Keaveney, J.; Kalogeropoulos, A.; Kleinwort, C.; Lohmann, W.; Mankel, R.; Maser, H.; Mittag, G.; Muhl, C.; Mussgiller, A.; Pitzl, D.; Reichelt, O.; Savitskyi, M.; Schuetze, P.; Walsh, R.; Zuber, A.; Biskop, H.; Buhmann, P.; Centis-Vignali, M.; Garutti, E.; Haller, J.; Hoffmann, M.; Klanner, R.; Matysek, M.; Perieanu, A.; Scharf, Ch.; Schleper, P.; Schmidt, A.; Schwandt, J.; Sonneveld, J.; Steinbrück, G.; Vormwald, B.; Wellhausen, J.; Abbas, M.; Amstutz, C.; Barvich, T.; Barth, Ch.; Boegelspacher, F.; De Boer, W.; Butz, E.; Casele, M.; Colombo, F.; Dierlamm, A.; Freund, B.; Hartmann, F.; Heindl, S.; Husemann, U.; Kornmeyer, A.; Kudella, S.; Muller, Th.; Printz, M.; Simonis, H. J.; Steck, P.; Weber, M.; Weiler, Th.; Anagnostou, G.; Asenov, P.; Assiouras, P.; Daskalakis, G.; Kyriakis, A.; Loukas, D.; Paspalaki, L.; Siklér, F.; Veszprémi, V.; Bhardwaj, A.; Dalal, R.; Jain, G.; Ranjan, K.; Dutta, S.; Chowdhury, S. Roy; Bakhshiansohl, H.; Behnamian, H.; Khakzad, M.; Naseri, M.; Cariola, P.; Creanza, D.; De Palma, M.; De Robertis, G.; Fiore, L.; Franco, M.; Loddo, F.; Sala, G.; Silvestris, L.; Maggi, G.; My, S.; Selvaggi, G.; Albergo, S.; Costa, S.; Di Mattia, A.; Giordano, F.; Potenza, R.; Saizu, M. A.; Tricomi, A.; Tuve, C.; Barbagli, G.; Brianzi, M.; Ciaranfi, R.; Ciulli, V.; Civinini, C.; D'Alessandro, R.; Focardi, E.; Latino, G.; Lenzi, P.; Meschini, M.; Paoletti, S.; Russo, L.; Scarlini, E.; Sguazzoni, G.; Strom, D.; Viliani, L.; Ferro, F.; Lo Vetere, M.; Robutti, E.; Dinardo, M. E.; Fiorendi, S.; Gennai, S.; Malvezzi, S.; Manzoni, R. A.; Menasce, D.; Moroni, L.; Pedrini, D.; Azzi, P.; Bacchetta, N.; Bisello, D.; Dall'Osso, M.; Pozzobon, N.; Tosi, M.; De Canio, F.; Gaioni, L.; Manghisoni, M.; Nodari, B.; Riceputi, E.; Re, V.; Traversi, G.; Comotti, D.; Ratti, L.; Alunni Solestizi, L.; Biasini, M.; Bilei, G. M.; Cecchi, C.; Checcucci, B.; Ciangottini, D.; Fanò, L.; Gentsos, C.; Ionica, M.; Leonardi, R.; Manoni, E.; Mantovani, G.; Marconi, S.; Mariani, V.; Menichelli, M.; Modak, A.; Morozzi, A.; Moscatelli, F.; Passeri, D.; Placidi, P.; Postolache, V.; Rossi, A.; Saha, A.; Santocchia, A.; Storchi, L.; Spiga, D.; Androsov, K.; Azzurri, P.; Arezzini, S.; Bagliesi, G.; Basti, A.; Boccali, T.; Borrello, L.; Bosi, F.; Castaldi, R.; Ciampa, A.; Ciocci, M. A.; Dell'Orso, R.; Donato, S.; Fedi, G.; Giassi, A.; Grippo, M. T.; Ligabue, F.; Lomtadze, T.; Magazzu, G.; Martini, L.; Mazzoni, E.; Messineo, A.; Moggi, A.; Morsani, F.; Palla, F.; Palmonari, F.; Raffaelli, F.; Rizzi, A.; Savoy-Navarro, A.; Spagnolo, P.; Tenchini, R.; Tonelli, G.; Venturi, A.; Verdini, P. G.; Bellan, R.; Costa, M.; Covarelli, R.; Da Rocha Rolo, M.; Demaria, N.; Rivetti, A.; Dellacasa, G.; Mazza, G.; Migliore, E.; Monteil, E.; Pacher, L.; Ravera, F.; Solano, A.; Fernandez, M.; Gomez, G.; Jaramillo Echeverria, R.; Moya, D.; Gonzalez Sanchez, F. J.; Vila, I.; Virto, A. L.; Abbaneo, D.; Ahmed, I.; Albert, E.; Auzinger, G.; Berruti, G.; Bianchi, G.; Blanchot, G.; Bonnaud, J.; Caratelli, A.; Ceresa, D.; Christiansen, J.; Cichy, K.; Daguin, J.; D'Auria, A.; Detraz, S.; Deyrail, D.; Dondelewski, O.; Faccio, F.; Frank, N.; Gadek, T.; Gill, K.; Honma, A.; Hugo, G.; Jara Casas, L. M.; Kaplon, J.; Kornmayer, A.; Kottelat, L.; Kovacs, M.; Krammer, M.; Lenoir, P.; Mannelli, M.; Marchioro, A.; Marconi, S.; Mersi, S.; Martina, S.; Michelis, S.; Moll, M.; Onnela, A.; Orfanelli, S.; Pavis, S.; Peisert, A.; Pernot, J.-F.; Petagna, P.; Petrucciani, G.; Postema, H.; Rose, P.; Tropea, P.; Troska, J.; Tsirou, A.; Vasey, F.; Vichoudis, P.; Verlaat, B.; Zwalinski, L.; Bachmair, F.; Becker, R.; di Calafiori, D.; Casal, B.; Berger, P.; Djambazov, L.; Donega, M.; Grab, C.; Hits, D.; Hoss, J.; Kasieczka, G.; Lustermann, W.; Mangano, B.; Marionneau, M.; Martinez Ruiz del Arbol, P.; Masciovecchio, M.; Meinhard, M.; Perozzi, L.; Roeser, U.; Starodumov, A.; Tavolaro, V.; Wallny, R.; Zhu, D.; Amsler, C.; Bösiger, K.; Caminada, L.; Canelli, F.; Chiochia, V.; de Cosa, A.; Galloni, C.; Hreus, T.; Kilminster, B.; Lange, C.; Maier, R.; Ngadiuba, J.; Pinna, D.; Robmann, P.; Taroni, S.; Yang, Y.; Bertl, W.; Deiters, K.; Erdmann, W.; Horisberger, R.; Kaestli, H.-C.; Kotlinski, D.; Langenegger, U.; Meier, B.; Rohe, T.; Streuli, S.; Chen, P.-H.; Dietz, C.; Grundler, U.; Hou, W.-S.; Lu, R.-S.; Moya, M.; Cussans, D.; Flacher, H.; Goldstein, J.; Grimes, M.; Jacob, J.; Seif El Nasr-Storey, S.; Cole, J.; Hoad, C.; Hobson, P.; Morton, A.; Reid, I. D.; Auzinger, G.; Bainbridge, R.; Dauncey, P.; Fulcher, J.; Hall, G.; James, T.; Magnan, A.-M.; Pesaresi, M.; Raymond, D. M.; Uchida, K.; Braga, D.; Coughlan, J. A.; Harder, K.; Jones, L.; Ilic, J.; Murray, P.; Prydderch, M.; Tomalin, I. R.; Garabedian, A.; Heintz, U.; Narain, M.; Nelson, J.; Sagir, S.; Speer, T.; Swanson, J.; Tersegno, D.; Watson-Daniels, J.; Chertok, M.; Conway, J.; Conway, R.; Flores, C.; Lander, R.; Pellett, D.; Ricci-Tam, F.; Squires, M.; Thomson, J.; Yohay, R.; Burt, K.; Ellison, J.; Hanson, G.; Olmedo, M.; Si, W.; Yates, B. R.; Gerosa, R.; Sharma, V.; Vartak, A.; Yagil, A.; Zevi Della Porta, G.; Dutta, V.; Gouskos, L.; Incandela, J.; Kyre, S.; Mullin, S.; Qu, H.; White, D.; Dominguez, A.; Bartek, R.; Cumalat, J. P.; Ford, W. T.; Jensen, F.; Johnson, A.; Krohn, M.; Leontsinis, S.; Mulholland, T.; Stenson, K.; Wagner, S. R.; Apresyan, A.; Bolla, G.; Burkett, K.; Butler, J. N.; Cheung, H. W. K.; Chramowicz, J.; Christian, D.; Cooper, W. E.; Deptuch, G.; Derylo, G.; Gingu, C.; Grünendahl, S.; Hasegawa, S.; Hoff, J.; Howell, J.; Hrycyk, M.; Jindariani, S.; Johnson, M.; Kahlid, F.; Lei, C. M.; Lipton, R.; Lopes De Sá, R.; Liu, T.; Los, S.; Matulik, M.; Merkel, P.; Nahn, S.; Prosser, A.; Rivera, R.; Schneider, B.; Sellberg, G.; Shenai, A.; Spiegel, L.; Tran, N.; Uplegger, L.; Voirin, E.; Berry, D. R.; Chen, X.; Ennesser, L.; Evdokimov, A.; Evdokimov, O.; Gerber, C. E.; Hofman, D. J.; Makauda, S.; Mills, C.; Sandoval Gonzalez, I. D.; Alimena, J.; Antonelli, L. J.; Francis, B.; Hart, A.; Hill, C. S.; Parashar, N.; Stupak, J.; Bortoletto, D.; Bubna, M.; Hinton, N.; Jones, M.; Miller, D. H.; Shi, X.; Tan, P.; Baringer, P.; Bean, A.; Khalil, S.; Kropivnitskaya, A.; Majumder, D.; Wilson, G.; Ivanov, A.; Mendis, R.; Mitchell, T.; Skhirtladze, N.; Taylor, R.; Anderson, I.; Fehling, D.; Gritsan, A.; Maksimovic, P.; Martin, C.; Nash, K.; Osherson, M.; Swartz, M.; Xiao, M.; Acosta, J. G.; Cremaldi, L. M.; Oliveros, S.; Perera, L.; Summers, D.; Bloom, K.; Claes, D. R.; Fangmeier, C.; Gonzalez Suarez, R.; Monroy, J.; Siado, J.; Hahn, K.; Sevova, S.; Sung, K.; Trovato, M.; Bartz, E.; Gershtein, Y.; Halkiadakis, E.; Kyriacou, S.; Lath, A.; Nash, K.; Osherson, M.; Schnetzer, S.; Stone, R.; Walker, M.; Malik, S.; Norberg, S.; Ramirez Vargas, J. E.; Alyari, M.; Dolen, J.; Godshalk, A.; Harrington, C.; Iashvili, I.; Kharchilava, A.; Nguyen, D.; Parker, A.; Rappoccio, S.; Roozbahani, B.; Alexander, J.; Chaves, J.; Chu, J.; Dittmer, S.; McDermott, K.; Mirman, N.; Rinkevicius, A.; Ryd, A.; Salvati, E.; Skinnari, L.; Soffi, L.; Tao, Z.; Thom, J.; Tucker, J.; Zientek, M.; Akgün, B.; Ecklund, K. M.; Kilpatrick, M.; Nussbaum, T.; Zabel, J.; Betchart, B.; Covarelli, R.; Demina, R.; Hindrichs, O.; Petrillo, G.; Eusebi, R.; Patel, R.; Perloff, A.; Ulmer, K. A.; Delannoy, A. G.; D'Angelo, P.; Johns, W.

2018-03-01

A new CMS Tracker is under development for operation at the High Luminosity LHC from 2026 onwards. It includes an outer tracker based on dedicated modules that will reconstruct short track segments, called stubs, using spatially coincident clusters in two closely spaced silicon sensor layers. These modules allow the rejection of low transverse momentum track hits and reduce the data volume before transmission to the first level trigger. The inclusion of tracking information in the trigger decision is essential to limit the first level trigger accept rate. A customized front-end readout chip, the CMS Binary Chip (CBC), containing stub finding logic has been designed for this purpose. A prototype module, equipped with the CBC chip, has been constructed and operated for the first time in a 4 GeemVem/emc positron beam at DESY. The behaviour of the stub finding was studied for different angles of beam incidence on a module, which allows an estimate of the sensitivity to transverse momentum within the future CMS detector. A sharp transverse momentum threshold around 2 emVem/emc was demonstrated, which meets the requirement to reject a large fraction of low momentum tracks present in the LHC environment on-detector. This is the first realistic demonstration of a silicon tracking module that is able to select data, based on the particle's transverse momentum, for use in a first level trigger at the LHC . The results from this test are described here.

Preparation and characterization of TiO2 coated Fe nanofibers for electromagnetic wave absorber.

PubMed

Jang, Dae-Hwan; Song, Hanbok; Lee, Young-In; Lee, Kun-Jae; Kim, Ki Hyeon; Oh, Sung-Tag; Lee, Sang-Kwan; Choa, Yong-Ho

2011-01-01

Recently, electromagnetic interference (EMI) and electromagnetic compatibility (EMC) have become serious problems due to the growth of electronic device and next generation telecommunication. It is necessary to develop new electromagnetic wave absorbing material to overcome the limitation of electromagnetic wave shielding materials. The EMI attenuation is normally related to magnetic loss and dielectric loss. Therefore, magnetic material coating dielectric materials are required in this reason. In this study, TiO2 coated Fe nanofibers were prepared to improve their properties for electromagnetic wave absorption. Poly(vinylpyrrolidone) (PVP) and Iron (III) nitrate nonahydrate (Fe(NO3)3 x 9H2O) were used as starting materials for the synthesis of Fe oxide nanofibers. Fe oxide nanofibers were prepared by electrospinning in an electric field and heat treatment. TiO2 layer was coated on the surface of Fe oxide nanofibers using sol-gel process. After the reduction of TiO2 coated Fe oxide nanofibers, Fe nanofibers with a TiO2 coating layer of about 10 nm were successfully obtained. The morphology and structure of fibers were characterized by SEM, TEM, and XRD. In addition, the absorption properties of TiO2 coated Fe nanofibers were measured by network analyzer.

Critical Review of the ECSS-E-ST-20-07C ESD Test Set-Up for Testing Spacecraft Equipment

NASA Astrophysics Data System (ADS)

Pelissou, P.; Daout, B.; Romero, C.; Wolf, K.-F. J.

2016-05-01

Satellite equipment needs to be immune to electrostatic discharges (ESD) likely to occur in flight. Testing the susceptibility against ESD on spacecraft equipment is therefore an important part of the EMC test program. The test method according to ECSS-E-ST- 20-07C [1], which is commonly used in space industry, leaves undesirable degrees of freedom on how the test is performed, which in turn has an influence on the injected current and therefore on the test results. Because of the indirect coupling of ESD to circuits, the current waveform applied during the test and its repeatability are of high importance. In the frame of an ESTEC research contract (4000109887/13/NL/GLC), a critical review of the ECSS-E-ST-20-07C is performed to identify the influence factors which have an impact on the test repeatability.

The Electronic Medication Complete Communication (EMC2) Study: Rationale and Methods for a Randomized Controlled Trial of a Strategy to Promote Medication Safety in Ambulatory Care

PubMed Central

Bailey, Stacy Cooper; Paasche-Orlow, Michael K.; Adams, William G.; Brokenshire, Samantha A.; Hickson, Ryan P.; Oramasionwu, Christine U.; Curtis, Laura M.; Kwasny, Mary J.; Wolf, Michael S.

2016-01-01

Background Adverse drug events (ADEs) affect millions of patients annually and place a significant burden on the healthcare system. The Food and Drug Administration (FDA) has developed patient safety information for high-risk medications that pose serious public health concerns. However, there are currently few assurances that patients receive this information or are able to identify or respond correctly to ADEs. Objective To compare the effectiveness of the Electronic Medication Complete Communication (EMC2) Strategy to promote safe medication use and reporting of ADEs in comparison to usual care. Methods The automated EMC2 Strategy consists of: 1) provider alerts to counsel patients on medication risks, 2) the delivery of patient-friendly medication information via the electronic health record, and 3) an automated telephone assessment to identify potential medication concerns or ADEs. The study will take place in two community health centers in Chicago, IL. Adult, English or Spanish-speaking patients (N=1,200) who have been prescribed a high-risk medication will be enrolled and randomized to the intervention arm or usual care based upon practice location. The primary outcomes of the study are medication knowledge, proper medication use, and reporting of ADEs; these will be measured at baseline, 4 weeks, and three months. Intervention fidelity as well as barriers and costs of implementation will be evaluated. Conclusions The EMC2 Strategy automates a patient-friendly risk communication and surveillance process to promote safe medication use while minimizing clinic burden. This trial seeks to evaluate the effectiveness and feasibility of this strategy in comparison to usual care. PMID:27777127

Estimating risks for water-quality exceedances of total-copper from highway and urban runoff under predevelopment and current conditions with the Stochastic Empirical Loading and Dilution Model (SELDM)

USGS Publications Warehouse

Granato, Gregory E.; Jones, Susan C.; Dunn, Christopher N.; Van Weele, Brian

2017-01-01

The stochastic empirical loading and dilution model (SELDM) was used to demonstrate methods for estimating risks for water-quality exceedances of event-mean concentrations (EMCs) of total-copper. Monte Carlo methods were used to simulate stormflow, total-hardness, suspended-sediment, and total-copper EMCs as stochastic variables. These simulations were done for the Charles River Basin upstream of Interstate 495 in Bellingham, Massachusetts. The hydrology and water quality of this site were simulated with SELDM by using data from nearby, hydrologically similar sites. Three simulations were done to assess the potential effects of the highway on receiving-water quality with and without highway-runoff treatment by a structural best-management practice (BMP). In the low-development scenario, total copper in the receiving stream was simulated by using a sediment transport curve, sediment chemistry, and sediment-water partition coefficients. In this scenario, neither the highway runoff nor the BMP effluent caused concentration exceedances in the receiving stream that exceed the once in three-year threshold (about 0.54 percent). In the second scenario, without the highway, runoff from the large urban areas in the basin caused exceedances in the receiving stream in 2.24 percent of runoff events. In the third scenario, which included the effects of the urban runoff, neither the highway runoff nor the BMP effluent increased the percentage of exceedances in the receiving stream. Comparison of the simulated geometric mean EMCs with data collected at a downstream monitoring site indicates that these simulated values are within the 95-percent confidence interval of the geometric mean of the measured EMCs.

Performance of two commercial electron beam algorithms over regions close to the lung-mediastinum interface, against Monte Carlo simulation and point dosimetry in virtual and anthropomorphic phantoms.

PubMed

Ojala, J; Hyödynmaa, S; Barańczyk, R; Góra, E; Waligórski, M P R

2014-03-01

Electron radiotherapy is applied to treat the chest wall close to the mediastinum. The performance of the GGPB and eMC algorithms implemented in the Varian Eclipse treatment planning system (TPS) was studied in this region for 9 and 16 MeV beams, against Monte Carlo (MC) simulations, point dosimetry in a water phantom and dose distributions calculated in virtual phantoms. For the 16 MeV beam, the accuracy of these algorithms was also compared over the lung-mediastinum interface region of an anthropomorphic phantom, against MC calculations and thermoluminescence dosimetry (TLD). In the phantom with a lung-equivalent slab the results were generally congruent, the eMC results for the 9 MeV beam slightly overestimating the lung dose, and the GGPB results for the 16 MeV beam underestimating the lung dose. Over the lung-mediastinum interface, for 9 and 16 MeV beams, the GGPB code underestimated the lung dose and overestimated the dose in water close to the lung, compared to the congruent eMC and MC results. In the anthropomorphic phantom, results of TLD measurements and MC and eMC calculations agreed, while the GGPB code underestimated the lung dose. Good agreement between TLD measurements and MC calculations attests to the accuracy of "full" MC simulations as a reference for benchmarking TPS codes. Application of the GGPB code in chest wall radiotherapy may result in significant underestimation of the lung dose and overestimation of dose to the mediastinum, affecting plan optimization over volumes close to the lung-mediastinum interface, such as the lung or heart. Copyright © 2013 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

The electronic medication complete communication (EMC2) study: Rationale and methods for a randomized controlled trial of a strategy to promote medication safety in ambulatory care.

PubMed

Bailey, Stacy Cooper; Paasche-Orlow, Michael K; Adams, William G; Brokenshire, Samantha A; Hickson, Ryan P; Oramasionwu, Christine U; Curtis, Laura M; Kwasny, Mary J; Wolf, Michael S

2016-11-01

Adverse drug events (ADEs) affect millions of patients annually and place a significant burden on the healthcare system. The Food and Drug Administration (FDA) has developed patient safety information for high-risk medications that pose serious public health concerns. However, there are currently few assurances that patients receive this information or are able to identify or respond correctly to ADEs. To evaluate the effectiveness of the Electronic Medication Complete Communication (EMC 2 ) Strategy to promote safe medication use and reporting of ADEs in comparison to usual care. The automated EMC 2 Strategy consists of: 1) provider alerts to counsel patients on medication risks, 2) the delivery of patient-friendly medication information via the electronic health record, and 3) an automated telephone assessment to identify potential medication concerns or ADEs. The study will take place in two community health centers in Chicago, IL. Adult, English or Spanish-speaking patients (N=1200) who have been prescribed a high-risk medication will be enrolled and randomized to the intervention arm or usual care based upon practice location. The primary outcomes of the study are medication knowledge, proper medication use, and reporting of ADEs; these will be measured at baseline, 4weeks, and three months. Intervention fidelity as well as barriers and costs of implementation will be evaluated. The EMC 2 Strategy automates a patient-friendly risk communication and surveillance process to promote safe medication use while minimizing clinic burden. This trial seeks to evaluate the effectiveness and feasibility of this strategy in comparison to usual care. Copyright © 2016 Elsevier Inc. All rights reserved.

[Output characteristics of rainfall runoff phosphorus pollution from a typical small watershed in Yimeng mountainous area].

PubMed

Yu, Xing-xiu; Li, Zhen-wei; Liu, Qian-jin; Jing, Guang-hua

2012-08-01

Relationships between phosphorus pollutant concentrations and precipitation-runoff were analyzed by monitoring pollutant losses at outlets of the Menglianggu watershed in 2010. A typical small watershed was selected to examine the runoff and quality parameters such as total phosphorus (TP), particle phosphorus (PP), dissolve phosphorus (DP) and dissolve inorganic phosphorus (DIP) in rainfall-runoff of 10 rainfall events. Precipitation was above 2 mm for all the 10 rainfall events. The results showed that the peak of phosphorus concentrations occurred before the peak of water flows, whereas change processes of the phosphorus fluxes were consistent with that of the water flows and the phosphorus flux also have a strong linear relationship with the water flows. The minimums of the phosphorus concentrations in every 10 natural rainfall events have small differences with each other, but the maximum and EMCs of the phosphorus concentrations have significant differences with each rainfall event. This was mainly influenced by the precipitation, maximum rainfall intensity and mean rainfall intensity (EMCs) and was less influenced by rainfall duration. DP and TP were mainly composed of DIP and PP, respectively. There were no significant correlations between DIP/DP dynamic changes and rainfall characteristics, whereas significant correlations between PP/TP dynamic changes and maximum rainfall intensity were detected. The production of DIP, DP, AND TP were mainly influenced by the direct runoff (DR) and base flow (BF). The EMCs of DIP, DP, TP and the variations of DIP/DP were all found to have significant polynomial relationships with DR/TR., but the dynamic changes of PP/ TP and the EMCS of PP were less influenced by the DR/TR.

Cryo-vacuum testing of the JWST Integrated Science Instrument Module (SPIE)

NASA Technical Reports Server (NTRS)

Kimble, Randy A.; Vila, M. Begona; Van Campen, Julie; Birkmann, Stephan M.; Comber, Brian J.; Fatig, Curtis C.; Glasse, Alistair C. H.; Glazer, Stuart D.; Kelly, Douglas M.; Mann, Steven D.;

Bulk Current Injection Testing of Cable Noise Reduction Techniques, 50 kHz to 400 MHz

NASA Technical Reports Server (NTRS)

Bradley, Arthur T.; Hare, Richard J.; Singh, Manisha

2009-01-01

This paper presents empirical results of cable noise reduction techniques as demonstrated using bulk current injection (BCI) techniques with radiated fields from 50 kHz - 400 MHz. It is a follow up to the two-part paper series presented at the Asia Pacific EMC Conference that focused on TEM cell signal injection. This paper discusses the effects of cable types, shield connections, and chassis connections on cable noise. For each topic, well established theories are compared with data from a real-world physical system.

Evaluation of the SEI using a multilayer spectroscopic ellipsometry model

DOE PAGES

Dufek, Eric J.

2014-08-28

A multilayer spectroscopic ellipsometry (SE) model has been developed to characterize SEI formation. The model, which consists of two Cauchy layers, is constructed with an inner layer meant to model primarily inorganic compounds adjacent to an electrode and an outer layer which mirrors polymeric, organic constituents on the exterior of the SEI. Comparison of 1:1 EC:EMC and 1:4 EC:EMC with 1.0 M LiPF₆ shows distinct differences in the two modeled layers. The data suggest that the thickness of both layers change over a wide potential range. These changes have been linked with other reports on the growth of the SEI.

A boy asked his Mom about energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mutolo, Paul F.; Muller, David; O'Dea, James

Representing the Energy Materials Center (EMC), this document is one of the entries in the Ten Hundred and One Word Challenge. As part of the challenge, the 46 Energy Frontier Research Centers were invited to represent their science in images, cartoons, photos, words and original paintings, but any descriptions or words could only use the 1000 most commonly used words in the English language, with the addition of one word important to each of the EFRCs and the mission of DOE energy. The mission of EMC is advancing the science of energy conversion and storage by understanding and exploiting fundamentalmore » properties of active materials and their interfaces.« less

Implementation of the 3D edge plasma code EMC3-EIRENE on NSTX

DOE PAGES

Lore, J. D.; Canik, J. M.; Feng, Y.; ...

2012-05-09

The 3D edge transport code EMC3-EIRENE has been applied for the first time to the NSTX spherical tokamak. A new disconnected double null grid has been developed to allow the simulation of plasma where the radial separation of the inner and outer separatrix is less than characteristic widths (e.g. heat flux width) at the midplane. Modelling results are presented for both an axisymmetric case and a case where 3D magnetic field is applied in an n = 3 configuration. In the vacuum approximation, the perturbed field consists of a wide region of destroyed flux surfaces and helical lobes which aremore » a mixture of long and short connection length field lines formed by the separatrix manifolds. This structure is reflected in coupled 3D plasma fluid (EMC3) and kinetic neutral particle (EIRENE) simulations. The helical lobes extending inside of the unperturbed separatrix are filled in by hot plasma from the core. The intersection of the lobes with the divertor results in a striated flux footprint pattern on the target plates. As a result, profiles of divertor heat and particle fluxes are compared with experimental data, and possible sources of discrepancy are discussed.« less

Development of an EMC3-EIRENE Synthetic Imaging Diagnostic

NASA Astrophysics Data System (ADS)

Meyer, William; Allen, Steve; Samuell, Cameron; Lore, Jeremy

2017-10-01

2D and 3D flow measurements are critical for validating numerical codes such as EMC3-EIRENE. Toroidal symmetry assumptions preclude tomographic reconstruction of 3D flows from single camera views. In addition, the resolution of the grids utilized in numerical code models can easily surpass the resolution of physical camera diagnostic geometries. For these reasons we have developed a Synthetic Imaging Diagnostic capability for forward projection comparisons of EMC3-EIRENE model solutions with the line integrated images from the Doppler Coherence Imaging diagnostic on DIII-D. The forward projection matrix is 2.8 Mpixel by 6.4 Mcells for the non-axisymmetric case we present. For flow comparisons, both simple line integral, and field aligned component matrices must be calculated. The calculation of these matrices is a massive embarrassingly parallel problem and performed with a custom dispatcher that allows processing platforms to join mid-problem as they become available, or drop out if resources are needed for higher priority tasks. The matrices are handled using standard sparse matrix techniques. Prepared by LLNL under Contract DE-AC52-07NA27344. This material is based upon work supported by the U.S. DOE, Office of Science, Office of Fusion Energy Sciences. LLNL-ABS-734800.

Modulation of Intraplate Deformation in Arizona due to Far-Reaching Postseismic Relaxation Following Plate Boundary Earthquakes

NASA Astrophysics Data System (ADS)

Kreemer, C.; Broermann, J.; Bennett, R. A.; Blewitt, G.

2016-12-01

The Basin and Range of southern Arizona is mostly devoid of active faults and seismicity, although M7+ earthquakes are known to have occurred in the Quaternary. Before the 2010 Mw=7.2 El-Mayor Cucapah (EMC) earthquake, we found from GPS data 2 mm/yr of extension across this region. After the EMC, we find that the extension across southern Arizona has been reduced to near-zero; this is part of a widespread change in the region's post-EMC deformation field that can be explained by viscoelastic relaxation of the lower crust and upper mantle. If the relaxation after the EMC is so wide-spread, similar affects must have occurred after other previous large earthquakes such that the deformation field is probably ever-changing, slowly. This transient deformation field obscures any long-term deformation and makes it difficult to assess the driving forces responsible for the deformation. To model the transient deformation we consider that the observed GPS-time-series record postseismic relaxation from the most recent large earthquakes: 1992 Landers, 1999 Hector Mine, 2009 Gulf of California, 2010 EMC, and 2012 Gulf of California. The postseismic model assumes an elastic upper crust to a depth of 15 km, a Maxwell visco-elastic lower crust at 15-30 km, a Burger's body rheology for the lithospheric mantle at 30-60 km, and an asthenosphere below 60 km. A best fitting viscosity was found by a random search over the parameter space of the three viscous layers and minimizing the misfit between the corrected time series and a least squares model that includes intercept, velocity, offsets at times of earthquakes and equipment offsets and annual and semi-annual terms. The overall best fitting viscosity for the lower crust 1019.9 Pa-s, lithospheric mantle 1019.6 Pa-s, and asthenospheric mantle 1018.8 Pa-s. Both the mantle viscosities are treated as Burger rheologies with a Kelvin Voigt element 1/10 of the Maxwell element. These viscosities predict very small present-day velocity gradients associated with relaxation from pre-1992 events. We will use the corrected GPS velocity field to explore the driving sources behind the velocity field; i.e., plate motion and spatial variation in gravitational potential energy.

Simulação de ejeções de massa coronal

NASA Astrophysics Data System (ADS)

Corsini, M. A.; Silva, A. V. R.

2003-08-01

Ejeções de massa coronal (EMC) são bolhas gigantes de gás permeadas por campos magnéticos que são ejetadas do Sol durante um período de várias horas. Caso estas ejeções atinjam a Terra, geralmente, causam uma série de distúrbios às comunicações de longa distância e navegação, além de danos a satélites e transformadores. Portanto, é desejável que sejamos capazes de prever quando estas ejeções atingirão a Terra. Para tanto, é necessário um bom entendimento dos mecanismos causadores das ejeções e, principalmente, de como se dá a propagação das EMC e sua interação com o vento solar que permeia o meio interplanetário. Nesse sentido foi desenvolvido um programa computacional para resolver as equações MHD (Magneto-Hidro-Dinâmica) que regem a evolução das EMC. Primeiramente foram estabelecidas as condições necessárias para descrever o vento solar, no estado estacionário, que permeia todo o meio interplanetário. Num primeiro momento, resolveu-se o sistema de equações para o caso do vento isotérmico, conhecida como a solução de Parker, a fim de testarmos o modelo. Então, foi considerado o caso do vento solar com temperatura variável no meio interplanetário. Este resultado foi utilizado como a base de nosso sistema em seu instante inicial. Posteriormente foram feitas as considerações necessárias para descrever a propagação da Ejeção de Massa Coronal. As EMC foram simuladas como um aumento de densidade e temperatura local na coroa solar. A órbita e a posição da Terra foram incluídas no sistema. Os dados gerados possibilitaram uma análise da evolução da EMC pelo meio interplanetário até encontrar-se com a Terra. Os perfis de densidade e temperatura a 1 Unidade Astronômica são comparados com os dados de satélites reportados na literatura.

Efficacy of elastic memory chains versus nickel-titanium coil springs in canine retraction: A two-center split-mouth randomized clinical trial.

PubMed

Khanemasjedi, Mashallah; Moradinejad, Mehrnaz; Javidi, Pedram; Niknam, Ozra; Jahromi, Nima Haghighat; Rakhshan, Vahid

2017-12-01

The use of newly-introduced elastic memory chains (EMCs) in space closure is increasingly gaining popularity. However, no clinical studies have evaluated their efficacy. Therefore, this study was conducted. In this two-center split-mouth single-blind randomized controlled trial, 21 jaws were divided into 42 quadrants. The two treatments [canine retraction using EMCs versus nickel-titanium (NiTi) coil springs (as control)] were randomly assigned to two quadrants of each jaw. The premolar space was measured at the baseline, and in the 1st, 2nd, and 3rd months of canine retraction, by a blinded orthodontist. Space closure rates were compared using a paired t-test. The rates of space closure using NiTi springs were 1.93±0.62, 1.71±0.75, and 1.36±0.51mm/month, during the 1st, 2nd, and 3rd months of treatment, respectively. The 3-month average rates of space closure were 1.67±0.39 and 1.89±0.36mm/month in the NiTi and elastic groups, respectively (faster in the elastic group, P=0.022). The application of elastic memory chains is as effective as NiTi springs. Copyright © 2017. Published by Elsevier Masson SAS.

Modern Space Craft - Antique Specifications

NASA Technical Reports Server (NTRS)

Brewer, Ron; Trout, Dawn

2006-01-01

Spacecraft now and of the future are being controlled by EMC requirements of the past. Little has been done by the launch vehicle/spacecraft manufacturers to abandon MIL-STD-461C which was released in 1986 because most of the electronics equipment being used aboard current launch vehicles is approved by similarity and heritage to MIL-STD-46 1 C and its predecessors. Twenty years later these electronic equipment items are still not tested to today's MIL-STD-461E requirements because there is a risk that the items will fail to meet the requirements and thus the cost will increase if it becomes necessary to redesign the equipment. That cost is insignificant compared with the cost of losing an entire mission! In the 20 years that have elapsed since MIL-STD-461C was released, the EMC environment has undergone major changes. High speed digital devices have been created that have fundamental clock and bus frequencies that span the entire LV/SC frequency range from the Flight Termination Systems through C and S-Band telemetry. Personnel involved in ground operations routinely carry and use hand held transceivers and cellular telephones close by sensitive electronics equipment. There are now many more orbiting receivers and emitters, plus range assets have increased dramatically since 2001. It's way past time to bring requirements up-to-date!

Humanoid Flight Metabolic Simulator Project

NASA Technical Reports Server (NTRS)

Ross, Stuart

2015-01-01

NASA's Evolvable Mars Campaign (EMC) has identified several areas of technology that will require significant improvements in terms of performance, capacity, and efficiency, in order to make a manned mission to Mars possible. These include crew vehicle Environmental Control and Life Support System (ECLSS), EVA suit Portable Life Support System (PLSS) and Information Systems, autonomous environmental monitoring, radiation exposure monitoring and protection, and vehicle thermal control systems (TCS). (MADMACS) in a Suit can be configured to simulate human metabolism, consuming crew resources (oxygen) in the process. In addition to providing support for testing Life Support on unmanned flights, MADMACS will also support testing of suit thermal controls, and monitor radiation exposure, body zone temperatures, moisture, and loads.

Mutual interferences and design principles for mechatronic devices in magnetic resonance imaging.

PubMed

Yu, Ningbo; Gassert, Roger; Riener, Robert

2011-07-01

Robotic and mechatronic devices that work compatibly with magnetic resonance imaging (MRI) are applied in diagnostic MRI, image-guided surgery, neurorehabilitation and neuroscience. MRI-compatible mechatronic systems must address the challenges imposed by the scanner's electromagnetic fields. We have developed objective quantitative evaluation criteria for device characteristics needed to formulate design guidelines that ensure MRI-compatibility based on safety, device functionality and image quality. The mutual interferences between an MRI system and mechatronic devices working in its vicinity are modeled and tested. For each interference, the involved components are listed, and a numerical measure for "MRI-compatibility" is proposed. These interferences are categorized into an MRI-compatibility matrix, with each element representing possible interactions between one part of the mechatronic system and one component of the electromagnetic fields. Based on this formulation, design principles for MRI-compatible mechatronic systems are proposed. Furthermore, test methods are developed to examine whether a mechatronic device indeed works without interferences within an MRI system. Finally, the proposed MRI-compatibility criteria and design guidelines have been applied to an actual design process that has been validated by the test procedures. Objective and quantitative MRI-compatibility measures for mechatronic and robotic devices have been established. Applying the proposed design principles, potential problems in safety, device functionality and image quality can be considered in the design phase to ensure that the mechatronic system will fulfill the MRI-compatibility criteria. New guidelines and test procedures for MRI instrument compatibility provide a rational basis for design and evaluation of mechatronic devices in various MRI applications. Designers can apply these criteria and use the tests, so that MRI-compatibility results can accrue to build an experiential database.

Radiated radiofrequency immunity testing of automated external defibrillators - modifications of applicable standards are needed

PubMed Central

2011-01-01

Background We studied the worst-case radiated radiofrequency (RF) susceptibility of automated external defibrillators (AEDs) based on the electromagnetic compatibility (EMC) requirements of a current standard for cardiac defibrillators, IEC 60601-2-4. Square wave modulation was used to mimic cardiac physiological frequencies of 1 - 3 Hz. Deviations from the IEC standard were a lower frequency limit of 30 MHz to explore frequencies where the patient-connected leads could resonate. Also testing up to 20 V/m was performed. We tested AEDs with ventricular fibrillation (V-Fib) and normal sinus rhythm signals on the patient leads to enable testing for false negatives (inappropriate "no shock advised" by the AED). Methods We performed radiated exposures in a 10 meter anechoic chamber using two broadband antennas to generate E fields in the 30 - 2500 MHz frequency range at 1% frequency steps. An AED patient simulator was housed in a shielded box and delivered normal and fibrillation waveforms to the AED's patient leads. We developed a technique to screen ECG waveforms stored in each AED for electromagnetic interference at all frequencies without waiting for the long cycle times between analyses (normally 20 to over 200 s). Results Five of the seven AEDs tested were susceptible to RF interference, primarily at frequencies below 80 MHz. Some induced errors could cause AEDs to malfunction and effectively inhibit operator prompts to deliver a shock to a patient experiencing lethal fibrillation. Failures occurred in some AEDs exposed to E fields between 3 V/m and 20 V/m, in the 38 - 50 MHz range. These occurred when the patient simulator was delivering a V-Fib waveform to the AED. Also, we found it is not possible to test modern battery-only-operated AEDs for EMI using a patient simulator if the IEC 60601-2-4 defibrillator standard's simulated patient load is used. Conclusions AEDs experienced potentially life-threatening false-negative failures from radiated RF, primarily below the lower frequency limit of present AED standards. Field strengths causing failures were at levels as low as 3 V/m at frequencies below 80 MHz where resonance of the patient leads and the AED input circuitry occurred. This plus problems with the standard's' prescribed patient load make changes to the standard necessary. PMID:21801368

Radiated radiofrequency immunity testing of automated external defibrillators--modifications of applicable standards are needed.

PubMed

Umberger, Ken; Bassen, Howard I

2011-07-29

We studied the worst-case radiated radiofrequency (RF) susceptibility of automated external defibrillators (AEDs) based on the electromagnetic compatibility (EMC) requirements of a current standard for cardiac defibrillators, IEC 60601-2-4. Square wave modulation was used to mimic cardiac physiological frequencies of 1-3 Hz. Deviations from the IEC standard were a lower frequency limit of 30 MHz to explore frequencies where the patient-connected leads could resonate. Also testing up to 20 V/m was performed. We tested AEDs with ventricular fibrillation (V-Fib) and normal sinus rhythm signals on the patient leads to enable testing for false negatives (inappropriate "no shock advised" by the AED). We performed radiated exposures in a 10 meter anechoic chamber using two broadband antennas to generate E fields in the 30-2500 MHz frequency range at 1% frequency steps. An AED patient simulator was housed in a shielded box and delivered normal and fibrillation waveforms to the AED's patient leads. We developed a technique to screen ECG waveforms stored in each AED for electromagnetic interference at all frequencies without waiting for the long cycle times between analyses (normally 20 to over 200 s). Five of the seven AEDs tested were susceptible to RF interference, primarily at frequencies below 80 MHz. Some induced errors could cause AEDs to malfunction and effectively inhibit operator prompts to deliver a shock to a patient experiencing lethal fibrillation. Failures occurred in some AEDs exposed to E fields between 3 V/m and 20 V/m, in the 38 - 50 MHz range. These occurred when the patient simulator was delivering a V-Fib waveform to the AED. Also, we found it is not possible to test modern battery-only-operated AEDs for EMI using a patient simulator if the IEC 60601-2-4 defibrillator standard's simulated patient load is used. AEDs experienced potentially life-threatening false-negative failures from radiated RF, primarily below the lower frequency limit of present AED standards. Field strengths causing failures were at levels as low as 3 V/m at frequencies below 80 MHz where resonance of the patient leads and the AED input circuitry occurred. This plus problems with the standard's' prescribed patient load make changes to the standard necessary.

EMC Test Report Electrodynamic Dust Shield

NASA Technical Reports Server (NTRS)

Carmody, Lynne M.; Boyette, Carl B.

2014-01-01

This report documents the Electromagnetic Interference E M I evaluation performed on the Electrodynamic Dust Shield (EDS) which is part of the MISSE-X System under the Electrostatics and Surface Physics Laboratory at Kennedy Space Center. Measurements are performed to document the emissions environment associated with the EDS units. The purpose of this report is to collect all information needed to reproduce the testing performed on the Electrodynamic Dust Shield units, document data gathered during testing, and present the results. This document presents information unique to the measurements performed on the Bioculture Express Rack payload; using test methods prepared to meet SSP 30238 requirements. It includes the information necessary to satisfy the needs of the customer per work order number 1037104. The information presented herein should only be used to meet the requirements for which it was prepared.

Blackhole formula and example relativity

NASA Astrophysics Data System (ADS)

Shin, Philip

Black hole formula 1) Second dimension (x,y) f(x)=y Energy E=m*c2 2) Third dimension (x,y,z) really x=y=z Black hole formula Root(c2)=c=Root(E/m) As mass go the velocity of light, mass become black hole so there are energy as multiply by mass. Example relativity When E=m*c2 1) Root(c2)=c=Root(E/m) 2) 3*c*Root(c2)=3*c*Root(E/m)=3*c2 From 1) to 2) as an example, As velocity is faster, mass increased. It means when velocity is increased, sec(time) is slower, and m(distance) is increased. The number is good to study physics.

Ground-based studies of tropisms in hardware developed for the European Modular Cultivation System (EMCS)

NASA Astrophysics Data System (ADS)

Correll, Melanie J.; Edelmann, Richard E.; Hangarter, Roger P.; Mullen, Jack L.; Kiss, John Z.

Phototropism and gravitropism play key roles in the oriented growth of roots in flowering plants. In blue or white light, roots exhibit negative phototropism, but red light induces positive phototropism in Arabidopsis roots. The blue-light response is controlled by the phototropins while the red-light response is mediated by the phytochrome family of photoreceptors. In order to better characterize root phototropism, we plan to perform experiments in microgravity so that this tropism can be more effectively studied without the interactions with the gravity response. Our experiments are to be performed on the European Modular Cultivation System (EMCS), which provides an incubator, lighting system, and high resolution video that are on a centrifuge palette. These experiments will be performed at μg, 1g (control) and fractional g-levels. In order to ensure success of this mission on the International Space Station, we have been conducting ground-based studies on growth, phototropism, and gravitropism in experimental unique equipment (EUE) that was designed for our experiments with Arabidopsis seedlings. Currently, the EMCS and our EUE are scheduled for launch on space shuttle mission STS-121. This project should provide insight into how the blue- and red-light signaling systems interact with each other and with the gravisensing system.

Effect of storage temperatures and humidity on proximate composition, peroxide value and iodine value of raw cashew nuts.

PubMed

Ajith, Sabna; Pramod, S; Prabha Kumari, C; Potty, V P

2015-07-01

The equilibrium moisture content (EMC) of raw cashew nuts (RCN) were determined using the standard static gravimetric method at 30 °C, 40 °C and 50 °C for relative humidity (RH) ranging from 43 to 90 %. The proximate composition analysis, peroxide value and iodine value of RCN were assessed at this equilibrium stage. The RCN kept under the humidity of 86 and 90 percentage at all studied temperatures developed mold growth within 24-48 h of time. The better storage condition assessed for raw cashew nut is 67 % of RH at 30 °C and the values obtained for EMC, proximate composition analysis, peroxide value and iodine value are within the same range as observed with harvested RCN. Highlights • Raw cashew nut storage condition identified • It was analysed with different temperature (30 (°)C, 40 (°)C and 50 (°)C) and relative humidity (43 %-90 %) • Better storage condition for raw cashew nut is in 67 % of RH at 30 (°)C • In this condition the EMC was 8.11 % as within the range of moisture in harvested RCN.

An age-related change in susceptibility of rat brain to encephalomyocarditis virus infection

PubMed Central

IKEGAMI, HISASHI; TAKEDA, MAKIO; DOI, KUNIO

1997-01-01

Rats were inoculated intraperitoneally (i.p.) or intracerebrally (i.c.) with 1 × 104 plaque forming units (PFU)/animal of the D variant of encephalomyocarditis virus (EMC-D) at 2, 4, 7, 14, 28 or 56 days of age for virological and histopathological examination. In the i.p.-inoculation study, neither viral replication nor lesions were detected in the animals inoculated at 28 and 56 days of age. In the animals inoculated when younger than 14 days of age, lesions were restricted to the brain although viral replication was detected in the brain, heart and pancreas. The brain lesions were characterized by acute meningoencephalitis with neuronal necrosis in the cerebral cortex, hippocampus and thalamus, and viral RNA was detected in degenerated and/or intact neurons. In the i.c.-inoculation study, similar age-related changes in susceptibility of rat brain to EMC-D infection were observed, but a minor difference was that viral replication and lesions were still detected in the hippocampus of some animals inoculated at 28 days of age. These results suggest that an age-related decrease in the susceptibility of rat brain to EMC virus infection may reflect an age-related change in the susceptibility of neurons themselves as well as in maturation of the immune system. PMID:9203984

Lithium ion solvation and diffusion in bulk organic electrolytes from first-principles and classical reactive molecular dynamics.

PubMed

Ong, Mitchell T; Verners, Osvalds; Draeger, Erik W; van Duin, Adri C T; Lordi, Vincenzo; Pask, John E

2015-01-29

Lithium-ion battery performance is strongly influenced by the ionic conductivity of the electrolyte, which depends on the speed at which Li ions migrate across the cell and relates to their solvation structure. The choice of solvent can greatly impact both the solvation and diffusivity of Li ions. In this work, we used first-principles molecular dynamics to examine the solvation and diffusion of Li ions in the bulk organic solvents ethylene carbonate (EC), ethyl methyl carbonate (EMC), and a mixture of EC and EMC. We found that Li ions are solvated by either carbonyl or ether oxygen atoms of the solvents and sometimes by the PF6(-) anion. Li(+) prefers a tetrahedrally coordinated first solvation shell regardless of which species are involved, with the specific preferred solvation structure dependent on the organic solvent. In addition, we calculated Li diffusion coefficients in each electrolyte, finding slightly larger diffusivities in the linear carbonate EMC compared to the cyclic carbonate EC. The magnitude of the diffusion coefficient correlates with the strength of Li(+) solvation. Corresponding analysis for the PF6(-) anion shows greater diffusivity associated with a weakly bound, poorly defined first solvation shell. These results can be used to aid in the design of new electrolytes to improve Li-ion battery performance.

Comparing deep neural network and other machine learning algorithms for stroke prediction in a large-scale population-based electronic medical claims database.

PubMed

Chen-Ying Hung; Wei-Chen Chen; Po-Tsun Lai; Ching-Heng Lin; Chi-Chun Lee

2017-07-01

Electronic medical claims (EMCs) can be used to accurately predict the occurrence of a variety of diseases, which can contribute to precise medical interventions. While there is a growing interest in the application of machine learning (ML) techniques to address clinical problems, the use of deep-learning in healthcare have just gained attention recently. Deep learning, such as deep neural network (DNN), has achieved impressive results in the areas of speech recognition, computer vision, and natural language processing in recent years. However, deep learning is often difficult to comprehend due to the complexities in its framework. Furthermore, this method has not yet been demonstrated to achieve a better performance comparing to other conventional ML algorithms in disease prediction tasks using EMCs. In this study, we utilize a large population-based EMC database of around 800,000 patients to compare DNN with three other ML approaches for predicting 5-year stroke occurrence. The result shows that DNN and gradient boosting decision tree (GBDT) can result in similarly high prediction accuracies that are better compared to logistic regression (LR) and support vector machine (SVM) approaches. Meanwhile, DNN achieves optimal results by using lesser amounts of patient data when comparing to GBDT method.

Neutron observables from inclusive lepton scattering on nuclei

NASA Astrophysics Data System (ADS)

Rinat, A. S.; Taragin, M. F.

2010-07-01

We analyze new data from Thomas Jefferson National Accelerator Facility (JLab) for inclusive electron scattering on various targets. Computed and measured total inclusive cross sections in the range 0.3≲x≲0.95 show reasonable agreement on a logarithmic scale for all targets. However, closer inspection of the quasielastic components reveals serious discrepancies. European Muon Collaboration (EMC) ratios with conceivably smaller systematic errors fare the same. As a consequence, the new data do not enable the extraction of the magnetic form factor GMn and the structure function F2n of the neutron, although the application of exactly the same analysis to older data had been successful. We incorporate in the above analysis older CLAS Collaboration data on F22H. Removal of some scattered points from those makes it appear possible to obtain the desired neutron information. We compare our results with others from alternative sources. Special attention is paid to the A=3 isodoublet cross sections and EMC ratios. Present data exist only for He3, but the available input in combination with charge symmetry enables computations for H3. Their average is the computed isoscalar part and is compared with the empirical modification of He3 EMC ratios toward a fictitious A=3 isosinglet.

SU-E-T-344: Validation and Clinical Experience of Eclipse Electron Monte Carlo Algorithm (EMC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pokharel, S; Rana, S

2014-06-01

Purpose: The purpose of this study is to validate Eclipse Electron Monte Carlo (Algorithm for routine clinical uses. Methods: The PTW inhomogeneity phantom (T40037) with different combination of heterogeneous slabs has been CT-scanned with Philips Brilliance 16 slice scanner. The phantom contains blocks of Rando Alderson materials mimicking lung, Polystyrene (Tissue), PTFE (Bone) and PMAA. The phantom has 30×30×2.5 cm base plate with 2cm recesses to insert inhomogeneity. The detector systems used in this study are diode, tlds and Gafchromic EBT2 films. The diode and tlds were included in CT scans. The CT sets are transferred to Eclipse treatment planningmore » system. Several plans have been created with Eclipse Monte Carlo (EMC) algorithm 11.0.21. Measurements have been carried out in Varian TrueBeam machine for energy from 6–22mev. Results: The measured and calculated doses agreed very well for tissue like media. The agreement was reasonably okay for the presence of lung inhomogeneity. The point dose agreement was within 3.5% and Gamma passing rate at 3%/3mm was greater than 93% except for 6Mev(85%). The disagreement can reach as high as 10% in the presence of bone inhomogeneity. This is due to eclipse reporting dose to the medium as opposed to the dose to the water as in conventional calculation engines. Conclusion: Care must be taken when using Varian Eclipse EMC algorithm for dose calculation for routine clinical uses. The algorithm dose not report dose to water in which most of the clinical experiences are based on rather it just reports dose to medium directly. In the presence of inhomogeneity such as bone, the dose discrepancy can be as high as 10% or even more depending on the location of normalization point or volume. As Radiation oncology as an empirical science, care must be taken before using EMC reported monitor units for clinical uses.« less

A comparative study of the grain-size distribution of surface dust and stormwater runoff quality on typical urban roads and roofs in Beijing, China.

PubMed

Shen, Zhenyao; Liu, Jin; Aini, Guzhanuer; Gong, Yongwei

2016-02-01

The deposition of pollutants on impervious surfaces is a serious problem associated with rapid urbanization, which results in non-point-source pollution. Characterizing the build-up and wash-off processes of pollutants in urban catchments is essential for urban planners. In this paper, the spatial variation and particle-size distributions of five heavy metals and two nutrients in surface dust were analyzed, and the runoff water first-flush effect (FF30) and event-mean concentrations (EMCs) of 10 common constituents were characterized. The relationships between runoff variables and stormwater characteristics were examined from three typical urban impervious surfaces in Beijing, China. Dust on road surfaces with smaller grain sizes had higher pollutant concentrations, whereas concentrations of Mn, Zn, Fe, and TP in roof surface dust increased with grain size. Particles with grain sizes of 38-74 and 125-300 μm contributed most to the total pollutant load in roads, while particles with the smallest grain sizes (<38 μm) contributed most on roofs (23.46-41.71 %). Event-mean concentrations (EMCs) and FF30 values for most runoff pollutants tended to be higher on roofs than on roads. The maximum intensity (I max) and the antecedent dry days (ADD) were critical parameters for EMCs in roads, while ADD was the only dominant parameter for EMCs on our studied roof. The rainfall intensity (RI) and maximum intensity (I max) were found to be the parameters with the strongest correlation to the first-flush effect on both roads and roofs. Significant correlations of total suspended solids (TSS) concentration in runoff with grain-size fractions of surface dust indicated that coarser particles (74-300 μm) are most likely to contribute to the solid-phase pollutants, and finer particles (<38 μm) are likely the main source of dissolved pollutants.

Key factors affecting urban runoff pollution under cold climatic conditions

NASA Astrophysics Data System (ADS)

Valtanen, Marjo; Sillanpää, Nora; Setälä, Heikki

2015-10-01

Urban runoff contains various pollutants and has the potential of deteriorating the quality of aquatic ecosystems. In this study our objective is to shed light on the factors that control the runoff water quality in urbanized catchments. The effects of runoff event characteristics, land use type and catchment imperviousness on event mass loads (EML) and event mean concentrations (EMC) were studied during warm and cold periods in three study catchments (6.1, 6.5 and 12.6 ha in size) in the city of Lahti, Finland. Runoff and rainfall were measured continuously for two years at each catchment. Runoff samples were taken for total nutrients (tot-P and tot-N), total suspended solids (TSS), heavy metals (Zn, Cr, Al, Co, Ni, Cu, Pb, Mn) and total organic carbon (TOC). Stepwise multiple linear regression analysis (SMLR) was used to identify general relationships between the following variables: event water quality, runoff event characteristics and catchment characteristics. In general, the studied variables explained 50-90% of the EMLs but only 30-60% of the EMCs, with runoff duration having an important role in most of the SMLR models. Mean runoff intensity or peak flow was also often included in the runoff quality models. Yet, the importance (being the first, second or third best) and role (negative or positive impact) of the explanatory variables varied between the cold and warm period. Land use type often explained cold period concentrations, but imperviousness alone explained EMCs weakly. As for EMLs, the influence of imperviousness and/or land use was season and pollutant dependent. The study suggests that pollutant loads can be - throughout the year - adequately predicted by runoff characteristics given that seasonal differences are taken into account. Although pollutant concentrations were sensitive to variation in seasonal and catchment conditions as well, the accurate estimation of EMCs would require a more complete set of explanatory factors than used in this study.

Quality of care for patients with type 2 diabetes mellitus in the Netherlands and the United States: a comparison of two quality improvement programs.

PubMed

Valk, Gerlof D; Renders, Carry M; Kriegsman, Didi M W; Newton, Katherine M; Twisk, Jos W R; van Eijk, Jacques Th M; van der Wal, Gerrit; Wagner, Edward H

2004-08-01

To assess differences in diabetes care and patient outcomes by comparing two multifaceted quality improvement programs in two different countries, and to increase knowledge of effective elements of such programs. Primary care in the ExtraMural Clinic (EMC) of the Department of General Practice of the Vrije Universiteit in Amsterdam, the Netherlands, and the Group Health Cooperative (GHC), a group-model health maintenance organization (HMO) in western Washington State in the United States. Data were collected from 1992 to 1997. In this observational study two diabetes cohorts in which a quality improvement program was implemented were compared. Both programs included a medical record system, clinical practice guidelines, physician educational meetings, audit, and feedback. Only the Dutch program (EMC) included guidelines on the structure of diabetes care and a recall system. Only the GHC program included educational outreach visits, formation of multidisciplinary teams, and patient self-management support. Included were 379 EMC patients, and 2,119 GHC patients with type 2 diabetes mellitus. Main process outcomes were: annual number of diabetes visits, and number of HbA1c and blood lipid measurements. Main patient outcomes were HbA1c and blood lipid levels. Multilevel analysis was used to adjust for dependency between repeated observations within one patient and for clustering of patients within general practices. In the EMC process outcomes and glycemic control improved more than at GHC, however, GHC had better baseline measures. There were no differences between programs on blood lipid control. During follow-up, intensification of pharmacotherapy was noted at both sites. Differences noted between programs were in line with differences in diabetes guidelines. Following implementation of guidelines and organizational improvement efforts, change occurred primarily in the process outcomes, rather than in the patient outcomes. Although much effort was put into improving process and patient outcomes, both complex programs still showed only moderate effects.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carver, R; Popple, R; Benhabib, S

Purpose: To evaluate the accuracy of electron dose distribution calculated by the Varian Eclipse electron Monte Carlo (eMC) algorithm for use with recent commercially available bolus electron conformal therapy (ECT). Methods: eMC-calculated electron dose distributions for bolus ECT have been compared to those previously measured for cylindrical phantoms (retromolar trigone and nose), whose axial cross sections were based on the mid-PTV CT anatomy for each site. The phantoms consisted of SR4 muscle substitute, SR4 bone substitute, and air. The bolus ECT treatment plans were imported into the Eclipse treatment planning system and calculated using the maximum allowable histories (2×10{sup 9}),more » resulting in a statistical error of <0.2%. Smoothing was not used for these calculations. Differences between eMC-calculated and measured dose distributions were evaluated in terms of absolute dose difference as well as distance to agreement (DTA). Results: Results from the eMC for the retromolar trigone phantom showed 89% (41/46) of dose points within 3% dose difference or 3 mm DTA. There was an average dose difference of −0.12% with a standard deviation of 2.56%. Results for the nose phantom showed 95% (54/57) of dose points within 3% dose difference or 3 mm DTA. There was an average dose difference of 1.12% with a standard deviation of 3.03%. Dose calculation times for the retromolar trigone and nose treatment plans were 15 min and 22 min, respectively, using 16 processors (Intel Xeon E5-2690, 2.9 GHz) on a Varian Eclipse framework agent server (FAS). Results of this study were consistent with those previously reported for accuracy of the eMC electron dose algorithm and for the .decimal, Inc. pencil beam redefinition algorithm used to plan the bolus. Conclusion: These results show that the accuracy of the Eclipse eMC algorithm is suitable for clinical implementation of bolus ECT.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cebe, M; Pacaci, P; Mabhouti, H

Purpose: In this study, the two available calculation algorithms of the Varian Eclipse treatment planning system(TPS), the electron Monte Carlo(eMC) and General Gaussian Pencil Beam(GGPB) algorithms were used to compare measured and calculated peripheral dose distribution of electron beams. Methods: Peripheral dose measurements were carried out for 6, 9, 12, 15, 18 and 22 MeV electron beams of Varian Triology machine using parallel plate ionization chamber and EBT3 films in the slab phantom. Measurements were performed for 6×6, 10×10 and 25×25cm{sup 2} cone sizes at dmax of each energy up to 20cm beyond the field edges. Using the same filmmore » batch, the net OD to dose calibration curve was obtained for each energy. Films were scanned 48 hours after irradiation using an Epson 1000XL flatbed scanner. Dose distribution measured using parallel plate ionization chamber and EBT3 film and calculated by eMC and GGPB algorithms were compared. The measured and calculated data were then compared to find which algorithm calculates peripheral dose distribution more accurately. Results: The agreement between measurement and eMC was better than GGPB. The TPS underestimated the out of field doses. The difference between measured and calculated doses increase with the cone size. The largest deviation between calculated and parallel plate ionization chamber measured dose is less than 4.93% for eMC, but it can increase up to 7.51% for GGPB. For film measurement, the minimum gamma analysis passing rates between measured and calculated dose distributions were 98.2% and 92.7% for eMC and GGPB respectively for all field sizes and energies. Conclusion: Our results show that the Monte Carlo algorithm for electron planning in Eclipse is more accurate than previous algorithms for peripheral dose distributions. It must be emphasized that the use of GGPB for planning large field treatments with 6 MeV could lead to inaccuracies of clinical significance.« less

Feasibility and systems definition study for microwave multi-application payload (MMAP)

NASA Technical Reports Server (NTRS)

Horton, J. B.; Allen, C. C.; Massaro, M. J.; Zemany, J. L.; Murrell, J. W.; Stanhouse, R. W.; Condon, G. P.; Stone, R. F.

1977-01-01

There were three Shuttle/Spacelab experiments: adaptive multibeam phased array antenna (AMPA) experiment, electromagnetic environment experiment (EEE), and millimeter wave communications experiment (MWCE). Work on the AMPA experiment was completed. Results included are definition of operating modes, sequence of operation, radii of operation about several ground stations, signal format, foot prints of typical orbits and preliminary definition of ground and user terminals. Definition of the MOD I EEE included conceptual hardware designs, spacelab interfaces, preliminary data handling methods, experiment tests and verification, and EMC studies. The MWCE was defined conceptually for a steerable high gain antenna.

Influences of Hydrological Regime on Runoff Quality and Pollutant Loadings in Tropical Urban Areas

NASA Astrophysics Data System (ADS)

Chow, M.; Yusop, Z.

2011-12-01

Experience in many developed countries suggests that non point source (NPS) pollution is still the main contributor to pollutant loadings into water bodies in urban areas. However, the mechanism of NPS pollutant transport and the influences of hydrologic regime on the pollutant loading are still unclear. Understanding these interactions will be useful for improving design criteria and strategies for controlling NPS pollution in urban areas. This issue is also extremely relevant in tropical environment because its rainfall and the runoff generation processes are so different from the temperate regions where most of the studies on NPS pollutant have been carried out. In this regard, an intensive study to investigate the extent of this pollution was carried out in Skudai, Johor, Malaysia. Three small catchments, each represents commercial, residential and industrial land use were selected. Stormwater samples and flow rate data were collected at these catchments over 52 storm events from year 2008 to 2009. Samples were analyzed for ten water quality constituents including total suspended solids, 5-day biochemical oxygen demand, chemical oxygen demand, oil and grease, nitrate nitrogen, nitrite nitrogen, ammonia nitrogen, soluble phosphorus, total phosphorus and zinc. Quality of stormwater runoff is estimated using Event Mean Concentration (EMC) value. The storm characteristics analyzed included rainfall depth, rainfall duration, mean intensity, max 5 minutes intensity, antecedent dry day, runoff volume and peak flow. Correlation coefficients were determined between storm parameters and EMCs for the residential, commercial and industrial catchments. Except for the antecedent storm mean intensity and antecedent dry days, the other rainfall and runoff variables were negatively correlated with EMCs of most pollutants. This study reinforced the earlier findings on the importance of antecedent dry days for causing greater EMC values with exceptions for oil and grease, nitrate nitrogen, total phosphorus and zinc. There is no positive correlation between rainfall intensity and EMC of constituents in all the studied catchments. In contrast, the pollutant loadings are influenced primarily by the rainfall and runoff characteristics. Rainfall depth, mean intensity, max 5 minute intensity, runoff volume and peak flow were positively correlated with the loadings of most of the constituents. Antecedent storm mean intensity and antecedent dry days seemed to be less important for estimating the pollutant loadings. Such study should be further conducted for acquiring a long term monitoring data related to storm runoff quality during rainfall, in order to have a better understanding on NPS pollution in urban areas.

Physical mechanisms affecting hot carrier-induced degradation in gallium nitride HEMTs

NASA Astrophysics Data System (ADS)

Mukherjee, Shubhajit

Gallium Nitride or GaN-based high electron mobility transistors (HEMTs) is currently the most promising device technology in several key military and civilian applications due to excellent high-power as well as high-frequency performance. Even though the performance figures are outstanding, GaN-based HEMTs are not as mature as some competing technologies, which means that establishing the reliability of the technology is important to enable use in critical applications. The objective of this research is to understand the physical mechanisms affecting the reliability of GaN HEMTs at moderate drain biases (typically VDS < 30 V in the devices considered here). The degradation in device performance is believed to be due to the formation or modification of charged defects near the interface by hydrogen depassivation processes (due to electron-activated hydrogen removal) from energetic carriers. A rate-equation describing the defect generation process is formulated based on this assumption. A combination of ensemble Monte-Carlo (EMC) simulation statistics, ab-initio density functional theory (DFT) calculations, and accelerated stress experiments is used to relate the candidate defects to the overall degradation behavior (VT and gm). The focus of this work is on the 'semi-ON' mode of transistor operation in which the degradation is usually observed to be at its highest. This semi-ON state is reasonably close to the biasing region of class-AB high power amplifiers, which are popular because of the combination of high efficiency and low distortion that is associated with this configuration. The carrier-energy distributions are obtained using an EMC simulator that was developed specifically for III-V HFETs. The rate equation is used to model the degradation at different operating conditions as well as longer stress times from the result of one short duration stress test, by utilizing the carrier-energy distribution obtained from EMC simulations for one baseline condition. This work also attempts to identify the spatial location of these defects, and how this impacts the V T shift and gm degradation of the devices.

Laser Processed Condensing Heat Exchanger Technology Development

NASA Technical Reports Server (NTRS)

Hansen, Scott; Wright, Sarah; Wallace, Sarah; Hamilton, Tanner; Dennis, Alexander; Zuhlke, Craig; Roth, Nick; Sanders, John

2017-01-01

The reliance on non-permanent coatings in Condensing Heat Exchanger (CHX) designs is a significant technical issue to be solved before long-duration spaceflight can occur. Therefore, high reliability CHXs have been identified by the Evolvable Mars Campaign (EMC) as critical technologies needed to move beyond low earth orbit. The Laser Processed Condensing Heat Exchanger project aims to solve these problems through the use of femtosecond laser processed surfaces, which have unique wetting properties and potentially exhibit anti-microbial growth properties. These surfaces were investigated to identify if they would be suitable candidates for a replacement CHX surface. Among the areas researched in this project include microbial growth testing, siloxane flow testing in which laser processed surfaces were exposed to siloxanes in an air stream, and manufacturability.

Antenna Measurements: Test & Analysis of the Radiated Emissions/Immunity of the NASA/Orion Spacecraft Dart Parachute Simulator & Prototype Capsule - The Crew Exploration Vehicle

NASA Technical Reports Server (NTRS)

Norgard, John D.

2012-01-01

For future NASA Manned Space Exploration of the Moon and Mars, a blunt body capsule, called the Orion Crew Exploration Vehicle (CEV), composed of a Crew Module (CM) and a Service Module (SM), with a parachute decent assembly is planned for reentry back to Earth. A Capsule Parachute Assembly System (CPAS) is being developed for preliminary prototype parachute drop tests at the Yuma Proving Ground (YPG) to simulate high-speed reentry to Earth from beyond Low-Earth-Orbit (LEO) and to provide measurements of position, velocity, acceleration, attitude, temperature, pressure, humidity, and parachute loads. The primary and secondary (backup) avionics systems on CPAS also provide mission critical firing events to deploy, reef, and release the parachutes in three stages (extraction, drogues, mains) using mortars and pressure cartridge assemblies. In addition, a Mid-Air Delivery System (MDS) is used to separate the capsule from the sled that is used to eject the capsule from the back of the drop plane. Also, high-speed and high-definition cameras in a Video Camera System (VCS) are used to film the drop plane extraction and parachute landing events. Intentional and unintentional radiation emitted from and received by antennas and electronic devices on/in the CEV capsule, the MDS sled, and the VCS system are being tested for radiated emissions/immunity (susceptibility) (RE/RS). To verify Electromagnetic Compatibility (EMC) of the Orion capsule, Electromagnetic Interference (EMI) measurements are being made inside a semi-anechoic chamber at NASA/JSC on the components of the CPAS system. Measurements are made at 1m from the components-under-test (CUT). In addition, EMI measurements of the integrated CEV system are being made inside a hanger at YPG. These measurements are made in a complete circle, at 30? angles or less, around the Orion Capsule, the spacecraft system under-test (SUT). Near-field B-Dot probe measurements on the surface of the Orion capsule are being extrapolated outward to the 1m standard distance for comparison to the MIL-STD radiated emissions limit, and far-field hybrid antenna measurements at 3m are being extrapolated inward to the 1m distance for similar comparisons.

David Florida Laboratory: Support for mobile satellite communications

NASA Technical Reports Server (NTRS)

Dumoulin, Jean-Guy; Mamen, Rolf

1995-01-01

The comprehensive integration and environmental (including RF) test facilities of the Canadian Space Agency's David Florida Laboratory (CSA)(DFL) were used extensively for the MSAT Program. Following a description of the facilities, the paper outlines their application to the qualification of the two MSAT satellites following an overview of the test plan. Particular emphasis is given to passive intermodulation measurement (PIM) demands, which for the MSAT satellites, contributed to the need to extend the anechoic chamber. The extended chamber was also used for an EMC test and SAR signature test of the RADARSAT satellite. The DFL's facilities are being used for additional aspects of mobile satellite communications. One shielded anechoic Extra High Frequency (EHF) chamber and associated test equipment are employed predominantly for measuring the performance of the IRIDIUM satellites' Engineering Model Gateway Moveable Antennas (EM)(GMA). Other chambers are used for testing aeronautical antennas on behalf of Inmarsat. Still others combine thermal and PIM testing. The paper concludes with a review of the test requirements of evolving satcom missions such as Inmarsat Aero-1.

Micro-cooler enhancements by barrier interface analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stephen, A.; Dunn, G. M.; Glover, J.

A novel gallium arsenide (GaAs) based micro-cooler design, previously analysed both experimentally and by an analytical Heat Transfer (HT) model, has been simulated using a self-consistent Ensemble Monte Carlo (EMC) model for a more in depth analysis of the thermionic cooling in the device. The best fit to the experimental data was found and was used in conjunction with the HT model to estimate the cooler-contact resistance. The cooling results from EMC indicated that the cooling power of the device is highly dependent on the charge distribution across the leading interface. Alteration of this charge distribution via interface extensions onmore » the nanometre scale has shown to produce significant changes in cooler performance.« less

Optimal design of active EMC filters

NASA Astrophysics Data System (ADS)

Chand, B.; Kut, T.; Dickmann, S.

2013-07-01

A recent trend in automotive industry is adding electrical drive systems to conventional drives. The electrification allows an expansion of energy sources and provides great opportunities for environmental friendly mobility. The electrical powertrain and its components can also cause disturbances which couple into nearby electronic control units and communication cables. Therefore the communication can be degraded or even permanently disrupted. To minimize these interferences, different approaches are possible. One possibility is to use EMC filters. However, the diversity of filters is very large and the determination of an appropriate filter for each application is time-consuming. Therefore, the filter design is determined by using a simulation tool including an effective optimization algorithm. This method leads to improvements in terms of weight, volume and cost.

The Architecture and Application of RAMSES, a CCSDS and ECSS PUS Compliant Test and Control System

NASA Astrophysics Data System (ADS)

Battelino, Milan; Svard, Christian; Carlsson, Anna; Carlstedt-Duke, Theresa; Tornqvist, Marcus

2010-08-01

SSC, Swedish Space Corporation, has more than 30 years of experience in developing test and control systems for sounding rockets, experimental test modules and satellites. The increasing amount of ongoing projects made SSC to consider developing a test and control system conformant to CCSDS (Consultative Committee for Space Data Systems) and ECSS (European Cooperation for Space Standardization), that with small effort and cost, could be reused between separate projects and products. The foreseen reduction in cost and development time for different future space-related projects made such a reusable control system desirable. This paper will describe the ideas behind the RAMSES (Rocket and Multi-Satellite EMCS Software) system, its architecture and how it has been and is being used in a variety of applications at SSC such as the multi-satellite mission PRISMA and sounding rocket project MAXUS-8.

Compatibility Studies of Hydrogen Peroxide and a New Hypergolic Fuel Blend

NASA Technical Reports Server (NTRS)

Baldridge, Jennifer; Villegas, Yvonne

2002-01-01

Several preliminary materials compatibility studies have been conducted to determine the practicality of a new hypergolic fuel system. Hypergolic fuel ignites spontaneously as the oxidizer decomposes and releases energy in the presence of the fuel. The bipropellant system tested consists of high-test hydrogen peroxide (HTP) and a liquid fuel blend consisting of a hydrocarbon fuel, an ignition enhancer and a transition metal catalyst. In order for further testing of the new fuel blend to take place, some basic materials compatibility and HTP decomposition studies must be accomplished. The thermal decomposition rate of HTP was tested using gas evolution and isothermal microcalorimetry (IMC). Materials were analyzed for compatibility with hydrogen peroxide including a study of the affect welding has on stainless steel elemental composition and its relation to HTP decomposition. Compatibility studies of valve materials in the fuel blend were performed to determine the corrosion resistance of the materials.

Biocompatibility studies in preparation for a spaceflight experiment on plant tropisms (TROPI)

NASA Astrophysics Data System (ADS)

Kiss, John Z.; Kumar, Prem; Bowman, Robert N.; Steele, Marianne K.; Eodice, Michael T.; Correll, Melanie J.; Edelmann, Richard E.

The interaction among tropisms is important in determining the growth form of a plant. Thus, we have developed a project to study the interaction between two key tropistic responses (i.e., gravitropism and phototropism) to be performed in microgravity on the International Space Station (ISS). Specifically, we are interested in the role of red-light-absorbing phytochrome pigments in modulating tropisms in seedlings of Arabidopsis thaliana. This project, termed TROPI for tropisms, is to be performed on the European Modular Cultivation System (EMCS), which provides an incubator with atmospheric control, lighting, and high-resolution video. The EMCS has two rotating centrifuge platforms so that our experiments can be performed at microgravity, 1g (control), and fractional g-levels. In order to optimize these spaceflight experiments, we have continued ground-based technical tests as well as basic science experiments. Since the seeds will have to be stored for several months in hardware prior to use on the ISS, we tested the effects of long-term storage of seeds in the TROPI EUE (experimental unique equipment) on germination rates and plant growth. The EUE consists of five seedling cassettes with LED lighting and a water delivery system in an Experimental Container (EC). Preliminary studies showed that there were reduced seed germination and plant growth after several months of storage in the EUE. We determined that the likely source of this biocompatibility problem was the conformal coating of electrical components of the EUE, which was required by NASA for safety reasons. In order to alleviate this problem, carbon filters were added to both the seedling cassettes and to the base of the EC. We expect that these improvements to the hardware will result in healthy plants capable of robust tropistic responses in our spaceflight experiments.

[Research of the Stormwater Runoff and Pollution Characteristics in Rural Area of Yuhang District, Hangzhou].

PubMed

Duan, Sheng-hui; Zhao, Yu; Shan, Bao-qing; Tang, Wen-zhong; Zhang, Wen-qiang; Zhang, Shu-zhen; Lang, Chao

2015-10-01

In order to investigate the pollution characteristics of stormwater runoff in the southern developed rural region, the runoff samples were collected from four different underlying surfaces during three storm events in Caoqiao and Pujia Tou, which are two typical villages and are located in Yuhang District of Hangzhou. The content of nutrition (nitrogen and phosphorus) and heavy metals (Mn, Cu, Zn, Ni, Cr, Cd, As, Pb) in the simples were analyzed, and the difference of EMC ( event mean concentration) and pollution load of the contaminants in the runoff on different underlying surfaces were compared. The results showed that the EMC of TSS, COD, NH4(+)-N, TP and TN were 16.19, 21.01, 0.74, 1.39 and 2.39 mg x L(-1) in the Caoqiao, respectively; as to Pujia Tou, they were 3.10, 15.69, 0.90, 0.78 and 3.58 mg x L(-1), respectively. The content of heavy metals was all lower than the national surface water quality of two type water in the runoff. Compared with the quality standards for surface water, the EMC of TP was 9 times and 3. 5 times higher and TN was 1. 8 times and 1. 2 times higher in two areas. Besides, the pollution loads of TSS and COD were the highest in farmland.

Intratracheal exposure of common marmosets to MERS-CoV Jordan-n3/2012 or MERS-CoV EMC/2012 isolates does not result in lethal disease

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Reed F., E-mail: johnsonreed@mail.nih.gov; Via, Laura E.; Kumar, Mia R.

Middle East Respiratory Syndrome Coronavirus (MERS-CoV) continues to be a threat to human health in the Middle East. Development of countermeasures is ongoing; however, an animal model that faithfully recapitulates human disease has yet to be defined. A recent study indicated that inoculation of common marmosets resulted in inconsistent lethality. Based on these data we sought to compare two isolates of MERS-CoV. We followed disease progression in common marmosets after intratracheal exposure with: MERS-CoV-EMC/2012, MERS-CoV-Jordan-n3/2012, media, or inactivated virus. Our data suggest that common marmosets developed a mild to moderate non-lethal respiratory disease, which was quantifiable by computed tomography (CT),more » with limited other clinical signs. Based on CT data, clinical data, and virological data, MERS-CoV inoculation of common marmosets results in mild to moderate clinical signs of disease that are likely due to manipulations of the marmoset rather than as a result of robust viral replication. - Highlights: • Common marmosets infected with MERS-EMC and MERS-JOR did not develop lethal disease. • Infected subjects developed transient signs of clinical disease. • CT indicated few differences between the infected and control groups. • Marmosets do not faithfully replicate human MERS pathogenesis.« less

Lithium Ion Solvation and Diffusion in Bulk Organic Electrolytes from First-Principles and Classical Reactive Molecular Dynamics

DOE PAGES

Ong, Mitchell T.; Verners, Osvalds; Draeger, Erik W.; ...

2014-12-19

We report that lithium-ion battery performance is strongly influenced by the ionic conductivity of the electrolyte, which depends on the speed at which Li ions migrate across the cell and relates to their solvation structure. The choice of solvent can greatly impact both the solvation and diffusivity of Li ions. In this work, we used first-principles molecular dynamics to examine the solvation and diffusion of Li ions in the bulk organic solvents ethylene carbonate (EC), ethyl methyl carbonate (EMC), and a mixture of EC and EMC. We found that Li ions are solvated by either carbonyl or ether oxygen atoms of the solvents and sometimes by the PF more » $$\\bar{6}$$ anion. Li + prefers a tetrahedrally coordinated first solvation shell regardless of which species are involved, with the specific preferred solvation structure dependent on the organic solvent. In addition, we calculated Li diffusion coefficients in each electrolyte, finding slightly larger diffusivities in the linear carbonate EMC compared to the cyclic carbonate EC. The magnitude of the diffusion coefficient correlates with the strength of Li + solvation. Corresponding analysis for the PF $$\\bar{6}$$ anion shows greater diffusivity associated with a weakly bound, poorly defined first solvation shell. In conclusion, these results can be used to aid in the design of new electrolytes to improve Li-ion battery performance.« less

Low-EC-Content Electrolytes for Low-Temperature Li-Ion Cells

NASA Technical Reports Server (NTRS)

Smart, Marshall; Bugga, Ratnakumar; Surampudi, Subbarao

2003-01-01

Electrolytes comprising LiPF6 dissolved at a concentration of 1.0 M in three different mixtures of alkyl carbonates have been found well suited for use in rechargeable lithium-ion electrochemical cells at low temperatures. These and other electrolytes have been investigated in continuing research directed toward extending the lower limit of practical operating temperatures of Li-ion cells down to -60 C. This research at earlier stages was reported in numerous previous NASA Tech Briefs articles, the three most recent being "Ethyl Methyl Carbonate as a Cosolvent for Lithium-Ion Cells" (NPO-20605), Vol. 25, Low-EC-Content Electrolytes for Low-Temperature Li-Ion Cells No. 6 (June 2001), page 53; "Alkyl Pyrocarbonate Electrolyte Additives for Li-Ion Cells" (NPO-20775), Vol. 26, No. 5 (May 2002), page 37; and "Fluorinated Alkyl Carbonates as Cosolvents in Li-Ion Cells (NPO-21076), Vol. 26, No. 5 (May 2002), page 38. The present solvent mixtures, in terms of volume proportions of their ingredients, are 1 ethylene carbonate (EC) + 1 diethyl carbonate (DEC) + 1 dimethyl carbonate (DMC) + 3 ethyl methyl carbonate (EMC); 3EC + 3DMC + 14EMC; and 1EC + 1DEC + 1DMC + 4EMC. Relative to similar mixtures reported previously, the present mixtures, which contain smaller proportions of EC, have been found to afford better performance in experimental Li-ion cells at temperatures < -20 C.

Fault geometry inversion and slip distribution of the 2010 Mw 7.2 El Mayor-Cucapah earthquake from geodetic data

NASA Astrophysics Data System (ADS)

Huang, Mong-Han; Fielding, Eric J.; Dickinson, Haylee; Sun, Jianbao; Gonzalez-Ortega, J. Alejandro; Freed, Andrew M.; Bürgmann, Roland

2017-01-01

The 4 April 2010 Mw 7.2 El Mayor-Cucapah (EMC) earthquake in Baja, California, and Sonora, Mexico, had primarily right-lateral strike-slip motion and a minor normal-slip component. The surface rupture extended about 120 km in a NW-SE direction, west of the Cerro Prieto fault. Here we use geodetic measurements including near- to far-field GPS, interferometric synthetic aperture radar (InSAR), and subpixel offset measurements of radar and optical images to characterize the fault slip during the EMC event. We use dislocation inversion methods and determine an optimal nine-segment fault geometry, as well as a subfault slip distribution from the geodetic measurements. With systematic perturbation of the fault dip angles, randomly removing one geodetic data constraint, or different data combinations, we are able to explore the robustness of the inferred slip distribution along fault strike and depth. The model fitting residuals imply contributions of early postseismic deformation to the InSAR measurements as well as lateral heterogeneity in the crustal elastic structure between the Peninsular Ranges and the Salton Trough. We also find that with incorporation of near-field geodetic data and finer fault patch size, the shallow slip deficit is reduced in the EMC event by reductions in the level of smoothing. These results show that the outcomes of coseismic inversions can vary greatly depending on model parameterization and methodology.

Three-dimensional simulation of H-mode plasmas with localized divertor impurity injection on Alcator C-Mod using the edge transport code EMC3-EIRENE

DOE PAGES

Lore, Jeremy D.; Reinke, M. L.; Brunner, D.; ...

2015-04-28

We study experiments in Alcator C-Mod to assess the level of toroidal asymmetry in divertor conditions resulting from poloidally and toroidally localized extrinsic impurity gas seeding show a weak toroidal peaking (~1.1) in divertor electron temperatures for high-power enhanced D-alpha H-modeplasmas. This is in contrast to similar experiments in Ohmically heated L-modeplasmas, which showed a clear toroidal modulation in the divertor electron temperature. Modeling of these experiments using the 3D edge transport code EMC3-EIRENE [Y. Feng et al., J. Nucl. Mater. 241, 930 (1997)] qualitatively reproduces these trends, and indicates that the different response in the simulations is due tomore » the ionization location of the injected nitrogen. Low electron temperatures in the private flux region (PFR) in L-mode result in a PFR plasma that is nearly transparent to neutral nitrogen, while in H-mode the impurities are ionized in close proximity to the injection location, with this latter case yielding a largely axisymmetric radiation pattern in the scrape-off-layer. In conclusion, the consequences for the ITER gas injection system are discussed. Quantitative agreement with the experiment is lacking in some areas, suggesting potential areas for improving the physics model in EMC3-EIRENE.« less

Changes in operational procedures to improve spaceflight experiments in plant biology in the European Modular Cultivation System

NASA Astrophysics Data System (ADS)

Kiss, John Z.; Aanes, Gjert; Schiefloe, Mona; Coelho, Liz H. F.; Millar, Katherine D. L.; Edelmann, Richard E.

2014-03-01

The microgravity environment aboard orbiting spacecraft has provided a unique laboratory to explore topics in basic plant biology as well as applied research on the use of plants in bioregenerative life support systems. Our group has utilized the European Modular Cultivation System (EMCS) aboard the International Space Station (ISS) to study plant growth, development, tropisms, and gene expression in a series of spaceflight experiments. The most current project performed on the ISS was termed Seedling Growth-1 (SG-1) which builds on the previous TROPI (for tropisms) experiments performed in 2006 and 2010. Major technical and operational changes in SG-1 (launched in March 2013) compared to the TROPI experiments include: (1) improvements in lighting conditions within the EMCS to optimize the environment for phototropism studies, (2) the use of infrared illumination to provide high-quality images of the seedlings, (3) modifications in procedures used in flight to improve the focus and overall quality of the images, and (4) changes in the atmospheric conditions in the EMCS incubator. In SG-1, a novel red-light-based phototropism in roots and hypocotyls of seedlings that was noted in TROPI was confirmed and now can be more precisely characterized based on the improvements in procedures. The lessons learned from sequential experiments in the TROPI hardware provide insights to other researchers developing space experiments in plant biology.

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar Climate Prediction (NCWCP) 5830 University Research Court College Park, MD 20740 Page Author: EMC

Formulation design of ranitidine hydrochloride to reduce its moisture absorption characteristics.

PubMed

Khan, Shagufta; Giradkar, Praful; Yeole, Pramod

2009-01-01

This investigation examined the effect of a ranitidine hydrocholoride (RHCl)-ion exchange resin complexation on the drug's moisture uptake behavior. Drug resin complexes (DRCs) were prepared using the batch method with (i) two weak cation exchange resins, Polacrilex with exchangeable H+ and Polacrillin potassium; and (ii) a strong cation exchange resin;Sodium polystyrene sulfonate. RHCl, simple resins, and DRCs were subjected to storage stability under 40 +/- 2 degrees C and 75 +/- 5% relative humidity (RH) for 16 h, and the resulting percent increase in weight was calculated. DRCs gained less moisture than the simple drug and free resins. Out of the three complexes tested, DRC containing Polacrilex resin showed the most promising effect in protecting RHCl against moisture uptake with an increase in weight of 10.22 +/- 17% (free RHCl gained 28.11%) and was thereby selected for tablet formulation. Tablets were prepared using simple RHCl with Starch 1500 (F1); low moisture-grade Starch 1500 LM (F2); RHCl as DRC with Starch 1500 (F3); and, Starch 1500 LM (F4). Tablets were tested for equilibrium moisture content (EMC) under different humidity conditions and hygroscopicity in the presence and absence of light. In addition, stability studies were run over the duration of 6 months in conditions under 40 +/- 2 degrees C and 75 +/- 5% RH. The EMC of tablets at 80% RH decreased in the following order: F1 > F2 > marketed coated tablet > F3 > F4. The results of hygroscopicity testing revealed that both rate and extent of moisture gain in the presence or absence of light by F3 and F4 were significantly less than F1, F2, and marketed coated tablet (P < 0.05). Stability studies showed insignificant changes in weight, breaking force, friability, and disintegration time for tablets containing resin, while significant changes in these properties were found in tablets without resin. Thus, Polacrilex resin with exchangeable H+ was found to be the best for protecting RHCl against moisture uptake.

Breeding graft-compatible Douglas-fir rootstocks (Pseudotsuga menziesii (Mirb.) Franco).

Treesearch

D.L. Copes

1999-01-01

A study encompassing 24 years was conducted to determine if a breeding program could produce highly graft-compatible rootstocks. Twenty-seven trees of apparent high graft compatibility were selected and crossed to produce 226 control-pollinated families. Seedlings were grown, field planted, and grafted with test scions. Graft unions from field tests were evaluated...

Hydrocarbon-fuel/combustion-chamber-liner materials compatibility

NASA Technical Reports Server (NTRS)

Gage, Mark L.

1990-01-01

Results of material compatibility experiments using hydrocarbon fuels in contact with copper-based combustion chamber liner materials are presented. Mil-Spec RP-1, n- dodecane, propane, and methane fuels were tested in contact with OFHC, NASA-Z, and ZrCu coppers. Two distinct test methods were employed. Static tests, in which copper coupons were exposed to fuel for long durations at constant temperature and pressure, provided compatibility data in a precisely controlled environment. Dynamic tests, using the Aerojet Carbothermal Test Facility, provided fuel and copper compatibility data under realistic booster engine service conditions. Tests were conducted using very pure grades of each fuel and fuels to which a contaminant, e.g., ethylene or methyl mercaptan, was added to define the role played by fuel impurities. Conclusions are reached as to degradation mechanisms and effects, methods for the elimination of these mechanisms, selection of copper alloy combustion chamber liners, and hydrocarbon fuel purchase specifications.

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar Prediction (NCWCP) 5830 University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar ) 5830 University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page generated:Sunday

Lithium-Ion Electrolytes Containing Flame Retardant Additives for Increased Safety Characteristics

NASA Technical Reports Server (NTRS)

Bugga, Ratnakumar V. (Inventor); Krause, Frederick Charles (Inventor); Smart, Marshall C. (Inventor); Prakash, Surya G. (Inventor); Smith, Kiah A. (Inventor)

2014-01-01

The invention discloses various embodiments of Li-ion electrolytes containing flame retardant additives that have delivered good performance over a wide temperature range, good cycle life characteristics, and improved safety characteristics, namely, reduced flammability. In one embodiment of the invention there is provided an electrolyte for use in a lithium-ion electrochemical cell, the electrolyte comprising a mixture of an ethylene carbonate (EC), an ethyl methyl carbonate (EMC), a fluorinated co-solvent, a flame retardant additive, and a lithium salt. In another embodiment of the invention there is provided an electrolyte for use in a lithium-ion electrochemical cell, the electrolyte comprising a mixture of an ethylene carbonate (EC), an ethyl methyl carbonate (EMC), a flame retardant additive, a solid electrolyte interface (SEI) film forming agent, and a lithium salt.

The effect of inhibitors of cellular RNA synthesis on stimulation of mouse encephalomyocarditis virus reproduction by poliovirus in HeLa and MIO cells.

PubMed

Shirman, G A; Maslova, S V

1978-05-01

Inoculation of HeLa and MIO cells with a guanidine-dependent mutant of poliovirus (gd-polio) in the absence of guanidine resulted in stimulation of mouse encephalomyocarditis (EMC) virus reproduction. No stimulation was found to occur in the presence of actinomycin D, on pre-treatment of the cells with cordycepin, or on their UV irradiation or enucleation. In contrast to HeLa cells, the enhancement of EMC virus reproduction by gd-polio in MIO cells required no current synthesis of cellular RNAs: it occurred in the presence of actinomycin D, upon UV irradiation of the cells or their enucleation. The possible mechanisms of the stimulating effect of poliovirus in HeLa and MIO cells are discussed.

Preparation of refractory cermet structures for lithium compatibility testing

NASA Technical Reports Server (NTRS)

Heestand, R. L.; Jones, R. A.; Wright, T. R.; Kizer, D. E.

1973-01-01

High-purity nitride and carbide cermets were synthesized for compatability testing in liquid lithium. A process was developed for the preparation of high-purity hafnium nitride powder, which was subsequently blended with tungsten powder or tantalum nitride and tungsten powders and fabricated into 3 in diameter billets by uniaxial hot pressing. Specimens were then cut from the billets for compatability testing. Similar processing techniques were applied to produce hafnium carbide and zirconium carbide cermets for use in the testing program. All billets produced were characterized with respect to chemistry, structure, density, and strength properties.

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page generated:Sunday, 27-May

Quality of Care for Patients with Type 2 Diabetes Mellitus in the Netherlands and the United States: A Comparison of Two Quality Improvement Programs

PubMed Central

Valk, Gerlof D; Renders, Carry M; Kriegsman, Didi MW; Newton, Katherine M; Twisk, Jos WR; van Eijk, Jacques ThM; van der Wal, Gerrit; Wagner, Edward H

2004-01-01

Objective To assess differences in diabetes care and patient outcomes by comparing two multifaceted quality improvement programs in two different countries, and to increase knowledge of effective elements of such programs. Study Setting Primary care in the ExtraMural Clinic (EMC) of the Department of General Practice of the Vrije Universiteit in Amsterdam, the Netherlands, and the Group Health Cooperative (GHC), a group-model health maintenance organization (HMO) in western Washington State in the United States. Data were collected from 1992 to 1997. Study Design In this observational study two diabetes cohorts in which a quality improvement program was implemented were compared. Both programs included a medical record system, clinical practice guidelines, physician educational meetings, audit, and feedback. Only the Dutch program (EMC) included guidelines on the structure of diabetes care and a recall system. Only the GHC program included educational outreach visits, formation of multidisciplinary teams, and patient self-management support. Data Collection Included were 379 EMC patients, and 2,119 GHC patients with type 2 diabetes mellitus. Main process outcomes were: annual number of diabetes visits, and number of HbA1c and blood lipid measurements. Main patient outcomes were HbA1c and blood lipid levels. Multilevel analysis was used to adjust for dependency between repeated observations within one patient and for clustering of patients within general practices. Principal Findings In the EMC process outcomes and glycemic control improved more than at GHC, however, GHC had better baseline measures. There were no differences between programs on blood lipid control. During follow-up, intensification of pharmacotherapy was noted at both sites. Differences noted between programs were in line with differences in diabetes guidelines. Conclusions Following implementation of guidelines and organizational improvement efforts, change occurred primarily in the process outcomes, rather than in the patient outcomes. Although much effort was put into improving process and patient outcomes, both complex programs still showed only moderate effects. PMID:15230924

Design Considerations for Spacecraft Operations During Uncrewed Dormant Phases of Human Exploration Missions

NASA Technical Reports Server (NTRS)

Williams-Byrd, Julie; Antol, Jeff; Jefferies, Sharon; Goodliff, Kandyce; Williams, Phillip; Ambrose, Rob; Sylvester, Andre; Anderson, Molly; Dinsmore, Craig; Hoffman, Stephen;

Validation results of specifications for motion control interoperability

NASA Astrophysics Data System (ADS)

Szabo, Sandor; Proctor, Frederick M.

1997-01-01

The National Institute of Standards and Technology (NIST) is participating in the Department of Energy Technologies Enabling Agile Manufacturing (TEAM) program to establish interface standards for machine tool, robot, and coordinate measuring machine controllers. At NIST, the focus is to validate potential application programming interfaces (APIs) that make it possible to exchange machine controller components with a minimal impact on the rest of the system. This validation is taking place in the enhanced machine controller (EMC) consortium and is in cooperation with users and vendors of motion control equipment. An area of interest is motion control, including closed-loop control of individual axes and coordinated path planning. Initial tests of the motion control APIs are complete. The APIs were implemented on two commercial motion control boards that run on two different machine tools. The results for a baseline set of APIs look promising, but several issues were raised. These include resolving differing approaches in how motions are programmed and defining a standard measurement of performance for motion control. This paper starts with a summary of the process used in developing a set of specifications for motion control interoperability. Next, the EMC architecture and its classification of motion control APIs into two classes, Servo Control and Trajectory Planning, are reviewed. Selected APIs are presented to explain the basic functionality and some of the major issues involved in porting the APIs to other motion controllers. The paper concludes with a summary of the main issues and ways to continue the standards process.

42 CFR 493.863 - Standard; Compatibility testing.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Standard; Compatibility testing. 493.863 Section 493.863 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN... for Laboratories Performing Tests of Moderate Complexity (including the Subcategory), High Complexity...

42 CFR 493.863 - Standard; Compatibility testing.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 5 2011-10-01 2011-10-01 false Standard; Compatibility testing. 493.863 Section 493.863 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN... for Laboratories Performing Tests of Moderate Complexity (including the Subcategory), High Complexity...

Organizational Change and the Individual.

ERIC Educational Resources Information Center

Fojt, Martin, Ed.

1995-01-01

Nineteen precis highlight concepts of managing change and people. Specific examples are provided from such companies as Texas Instruments, EMC, British Telecom, Cooper & Lybrands, MCB University Press, and the Royal Bank of Scotland. (SK)

Transportation-Driven Mars Surface Operations Supporting an Evolvable Mars Campaign

NASA Technical Reports Server (NTRS)

Toups, Larry; Brown, Kendall; Hoffman, Stephen J.

2015-01-01

This paper describes the results of a study evaluating options for supporting a series of human missions to a single Mars surface destination. In this scenario the infrastructure emplaced during previous visits to this site is leveraged in following missions. The goal of this single site approach to Mars surface infrastructure is to enable "Steady State" operations by at least 4 crew for up to 500 sols at this site. These characteristics, along with the transportation system used to deliver crew and equipment to and from Mars, are collectively known as the Evolvable Mars Campaign (EMC). Information in this paper is presented in the sequence in which it was accomplished. First, a logical buildup sequence of surface infrastructure was developed to achieve the desired "Steady State" operations on the Mars surface. This was based on a concept of operations that met objectives of the EMC. Second, infrastructure capabilities were identified to carry out this concept of operations. Third, systems (in the form of conceptual elements) were identified to provide these capabilities. This included top-level mass, power and volume estimates for these elements. Fourth, the results were then used in analyses to evaluate three options (18t, 27t, and 40t landed mass) of Mars Lander delivery capability to the surface. Finally, Mars arrival mass estimates were generated based upon the entry, descent, and landing requirements for inclusion in separate assessments of in-space transportation capabilities for the EMC.

Stormwater runoff pollutant loading distributions and their correlation with rainfall and catchment characteristics in a rapidly industrialized city.

PubMed

Li, Dongya; Wan, Jinquan; Ma, Yongwen; Wang, Yan; Huang, Mingzhi; Chen, Yangmei

2015-01-01

Fast urbanization and industrialization in developing countries result in significant stormwater runoff pollution, due to drastic changes in land-use, from rural to urban. A three-year study on the stormwater runoff pollutant loading distributions of industrial, parking lot and mixed commercial and residential catchments was conducted in the Tongsha reservoir watershed of Dongguan city, a typical, rapidly industrialized urban area in China. This study presents the changes in concentration during rainfall events, event mean concentrations (EMCs) and event pollution loads per unit area (EPLs). The first flush criterion, namely the mass first flush ratio (MFFn), was used to identify the first flush effects. The impacts of rainfall and catchment characterization on EMCs and pollutant loads percentage transported by the first 40% of runoff volume (FF40) were evaluated. The results indicated that the pollutant wash-off process of runoff during the rainfall events has significant temporal and spatial variations. The mean rainfall intensity (I), the impervious rate (IMR) and max 5-min intensity (Imax5) are the critical parameters of EMCs, while Imax5, antecedent dry days (ADD) and rainfall depth (RD) are the critical parameters of FF40. Intercepting the first 40% of runoff volume can remove 55% of TSS load, 53% of COD load, 58% of TN load, and 61% of TP load, respectively, according to all the storm events. These results may be helpful in mitigating stormwater runoff pollution for many other urban areas in developing countries.

Light assisted drying (LAD) for protein stabilization: optimization of laser processing parameters

NASA Astrophysics Data System (ADS)

Young, Madison A.; Antczak, Andrew T.; Elliott, Gloria D.; Trammell, Susan R.

2017-02-01

In this study, a novel light-based processing method to create an amorphous trehalose matrix for the stabilization of proteins is discussed. Near-IR radiation is used to remove water from samples, leaving behind an amorphous solid with embedded protein. This method has potential applications in the stabilization of protein-based therapeutics and diagnostics that are becoming widely used in the treatment and diagnosis of a variety of diseases. Freeze-drying or freezing are currently the standard for the preservation of proteins, but these methods are expensive and can be challenging in some environments due to a lack of available infrastructure. Light-assisted drying offers a relatively inexpensive method for drying samples. Proteins suspended in a trehalose solution are dehydrated using near-infrared laser light. The laser radiation speeds drying and as water is removed the sugar forms a protective matrix. The goal of this study is to determine processing parameters that result in fast processing times and low end moisture contents (EMC), while maintaining the functionality of embedded proteins. We compare the effect of changing processing wavelength, power and resulting sample temperature, and substrate material on the EMC for two NIR laser sources (1064 nm and 1850 nm). The 1850 nm laser resulted in the lowest EMC (0.1836+/-0.09 gH2O/gDryWeight) after 10 minutes of processing on borosilicate glass microfiber paper. This suggests a storage temperature of 3°C.

Investigation of a novel ternary electrolyte based on dimethyl sulfite and lithium difluoromono(oxalato)borate for lithium ion batteries

NASA Astrophysics Data System (ADS)

Chen, Renjie; Zhu, Lu; Wu, Feng; Li, Li; Zhang, Rong; Chen, Shi

2014-01-01

Lithium difluoromono(oxalato)borate (LiODFB) has been used as a novel lithium salt for battery in recent studies. In this study, a series of novel electrolytes has been prepared by adding 30 vol% dimethyl sulfite (DMS) or dimethyl carbonate (DMC) as co-solvent into an ethylene carbonate (EC)/ethyl methyl carbonate (EMC) + LiX mixture, in which the LiX could be LiClO4, LiODFB, LiBOB, LiTFSI, or LiCF3SO3. These ternary electrolytes have been investigated for use in lithium ion batteries. FT-IR spectroscopy analysis shows that characteristic functional groups (-CO3, -SO3) undergo red-shift or blue-shift with the addition of different lithium salts. The LiODFB-EC/EMC/DMS electrolyte exhibits high ionic conductivity, which is mainly because of the low melting point of DMS, and LiODFB possessing high solubility. The Li/MCMB cells containing this novel electrolyte exhibit high capacities, good cycling performance, and excellent rate performance. These performances are probably because both LiODFB and DMS can assist in the formation of SEI films by reductive decomposition. Additionally, the discharge capacity of Li/LiCoO2 half cell containing LiODFB-EC/EMC/DMS electrolyte is 130.9 mAh g-1 after 50 cycles, and it is very comparable with the standard-commercial electrolyte. The results show that this study produces a promising electrolyte candidate for lithium ion batteries.

Wide-Temperature Electrolytes for Lithium-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Qiuyan; Jiao, Shuhong; Luo, Langli

2017-05-26

Formulating electrolytes with solvents of low freezing points and high dielectric constants is a direct approach to extend the service temperature range of lithium (Li)-ion batteries (LIBs), for which propylene carbonate (PC), ethyl methyl carbonate (EMC), diethyl carbonate (DEC), methyl butyrate (MB) are excellent candidates. In this work, we report such low temperature electrolyte formulations by optimizing the content of ethylene carbonate (EC) in the EC-PC-EMC ternary solvent system with LiPF6 salt and CsPF6 additive. An extended service temperature range from 40°C to 60°C was obtained in LIBs with lithium nickel cobalt aluminum mixed oxide (LiNi0.80Co0.15Al0.05O2, NCA) as cathode andmore » graphite as anode. The discharge capacities at low temperatures and the cycle life at room and elevated temperatures were systematically investigated in association with the ionic conductivity and phase transition behaviors. The most promising electrolyte formulation was identified as 1.0 M LiPF6 in EC-PC-EMC (1:1:8 by wt.) with 0.05 M CsPF6, which was demonstrated in both coin cells of graphite||NCA and 1 Ah pouch cells of graphite||LiNi1/3Mn1/3Co1/3O2. This optimized electrolyte enables excellent wide-temperature performances, as evidenced by the 68% capacity retention at 40C and C/5 rate, and nearly identical stable cycle life at room and elevated temperatures up to 60C.« less

Stormwater Runoff Pollutant Loading Distributions and Their Correlation with Rainfall and Catchment Characteristics in a Rapidly Industrialized City

PubMed Central

Li, Dongya; Wan, Jinquan; Ma, Yongwen; Wang, Yan; Huang, Mingzhi; Chen, Yangmei

2015-01-01

Fast urbanization and industrialization in developing countries result in significant stormwater runoff pollution, due to drastic changes in land-use, from rural to urban. A three-year study on the stormwater runoff pollutant loading distributions of industrial, parking lot and mixed commercial and residential catchments was conducted in the Tongsha reservoir watershed of Dongguan city, a typical, rapidly industrialized urban area in China. This study presents the changes in concentration during rainfall events, event mean concentrations (EMCs) and event pollution loads per unit area (EPLs). The first flush criterion, namely the mass first flush ratio (MFFn), was used to identify the first flush effects. The impacts of rainfall and catchment characterization on EMCs and pollutant loads percentage transported by the first 40% of runoff volume (FF40) were evaluated. The results indicated that the pollutant wash-off process of runoff during the rainfall events has significant temporal and spatial variations. The mean rainfall intensity (I), the impervious rate (IMR) and max 5-min intensity (Imax5) are the critical parameters of EMCs, while Imax5, antecedent dry days (ADD) and rainfall depth (RD) are the critical parameters of FF40. Intercepting the first 40% of runoff volume can remove 55% of TSS load, 53% of COD load, 58% of TN load, and 61% of TP load, respectively, according to all the storm events. These results may be helpful in mitigating stormwater runoff pollution for many other urban areas in developing countries. PMID:25774922

Mixed-Salt/Ester Electrolytes for Low-Temperature Li+ Cells

NASA Technical Reports Server (NTRS)

Smart, Marshall; Bugga, Ratnakumar

2006-01-01

Electrolytes comprising, variously, LiPF6 or LiPF6 plus LiBF4 dissolved at various concentrations in mixtures of alkyl carbonates and alkyl esters have been found to afford improved low-temperature performance in rechargeable lithium-ion electrochemical cells. These and other electrolytes have been investigated in a continuing effort to extend the lower limit of operating temperatures of such cells. This research at earlier stages, and the underlying physical and chemical principles, were reported in numerous previous NASA Tech Briefs articles, the most recent being Ester-Based Electrolytes for Low-Temperature Li-Ion Cells (NPO-41097), NASA Tech Briefs, Vol. 29, No. 12 (December 2005), page 59. The ingredients of the solvent mixtures include ethylene carbonate (EC), ethyl methyl carbonate (EMC), methyl butyrate (MB), and methyl propionate (MP). The electrolytes were placed in Li-ion cells containing carbon anodes and LiNi0.8Co0.2O2 cathodes, and the electrical performances of the cells were measured over a range of temperatures down to 60 C. The electrolytes that yielded the best low-temperature performances were found to consist, variously, of 1.0 M LiPF6 + 0.4 M LiBF4 or 1.4 LiPF6 in 1EC + 1EMC + 8MP or 1EC + 1EMC + 8MB, where the concentrations of the salts are given in molar units and the proportions of the solvents are by relative volume.

Damage of Elastomeric Matrix Composites (EMC-rubbers) Under Static Loading Conditions: Experimental and Numerical Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayari, F.; Supmeca/LISMMA-Paris, School of Mechanical and Manufacturing Engineering; Bayraktar, E.

2011-01-17

Elastomeric matrix composites (EMC-rubbers) are considered as isotropic hyper elastic incompressible materials under static loading conditions. As a rubber material element cannot be extended to an infinite stretch ratio, a damage mechanism at large strain is considered. The phenomenon of cavitation plays an important role in the damage of EMCs and influences the toughening mechanism of rubber-modified plastics. Indeed, cavitation in elastomers is thought to be initiated from flaws, which grow primarily due to a hydrostatic tensile stress and ahead of the crack; there will not only be a high stress perpendicular to the plane of the crack but alsomore » significant stress components in the other direction. However, there exists historically much discussion on the evolution of the cavitation in elastomers under monotonic and/or static solicitation. Mainly, cavitation instability occurs when the stress levels are sufficiently high so that the void expansion rate becomes infinitely large. Many research works have been performed to understand the effects of rubber cavitation on toughening of plastics. In fact, the cavitation phenomenon is not well known in detail. The most popular idea states that the cavitation is related to the existence of the gas bubbles trapped in the material during the production stage and the growing of the cavities would then be the result of the growing gas bubbles. Further, instable failure mechanism at the end of the cavitation is not well known too.« less

Flammability, Offgassing, and Compatibility Requirements and Test Procedures. Interim NASA Technical Standard

NASA Technical Reports Server (NTRS)

2009-01-01

This Interim Standard establishes requirements for evaluation, testing, and selection of materials that are intended for use in space vehicles, associated Ground Support Equipment (GSE), and facilities used during assembly, test, and flight operations. Included are requirements, criteria, and test methods for evaluating the flammability, offgassing, and compatibility of materials.

3-D Deformation Field Of The 2010 El Mayor-Cucapah (Mexico) Earthquake From Matching Before To After Aerial Lidar Point Clouds

NASA Astrophysics Data System (ADS)

Hinojosa-Corona, A.; Nissen, E.; Arrowsmith, R.; Krishnan, A. K.; Saripalli, S.; Oskin, M. E.; Arregui, S. M.; Limon, J. F.

2012-12-01

The Mw 7.2 El Mayor-Cucapah earthquake (EMCE) of 4 April 2010 generated a ~110 km long, NW-SE trending rupture, with normal and right-lateral slip in the order of 2-3m in the Sierra Cucapah, the northern half, where the surface rupture has the most outstanding expression. Vertical and horizontal surface displacements produced by the EMCE have been addressed separately by other authors with a variety of aerial and satellite remote sensing techniques. Slip variation along fault and post-seismic scarp erosion and diffusion have been estimated in other studies using terrestrial LiDAR (TLS) on segments of the rupture. To complement these other studies, we computed the 3D deformation field by comparing pre- to post-event point clouds from aerial LiDAR surveys. The pre-event LiDAR with lower point density (0.013-0.033 pts m-2) required filtering and post-processing before comparing with the denser (9-18 pts m-2) more accurate post event dataset. The 3-dimensional surface displacement field was determined using an adaptation of the Iterative Closest Point (ICP) algorithm, implemented in the open source Point Cloud Library (PCL). The LiDAR datasets are first split into a grid of windows, and for each one, ICP iteratively converges on the rigid body transformation (comprising a translation and a rotation) that best aligns the pre- to post-event points. Testing on synthetic datasets perturbed with displacements of known magnitude showed that windows with dimensions of 100-200m gave the best results for datasets with these densities. Here we present the deformation field with detailed displacements in segments of the surface rupture where its expression was recognized by ICP from the point cloud matching, mainly the scarcely vegetated Sierra Cucapah with the Borrego and Paso Superior fault segments the most outstanding, where we are able to compare our results with values measured in the field and results from TLS reported in other works. EMC simulated displacement field for a 2m right lateral normal (east block down) slip on the pre-event point cloud along the Borrego fault on Sierra Cucapah. Shaded DEM from post-event point cloud as backdrop.

High-temperature compatibility study of iridium (DOP-26 alloy) with graphite and plutonia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Axler, K.M.; Eash, D.T.

1987-12-01

This report outlines the materials compatibility tests conducted on DOP-26 iridium alloy and carbon. The carbon used was in the form of woven graphite as present in the impact shell used to encase plutonia in nuclear heat sources. In addition, compatibility tests of the DOP-26 alloy with plutonia are described. The reactivity observed in both systems is discussed. 4 refs., 6 figs.

Experimental Interactions of Components of Hemodialysis Units with Human Blood

PubMed Central

Zucker, W. H.; Shinoda, B. A.; Mason, R. G.

1974-01-01

An in vitro model test system for estimation of the blood compatibility of hemodialysis membranes and tubing is described. The model test system consists of a modified hemodialysis unit and blood pump through which fresh citrated human blood is circulated. The effects of the use of different pump and tubing types upon hematologic and blood coagulation parameters are described. Preexposure of test surfaces to albumin appeared to enhance blood compatibility characteristics of the model test system, whereas preexposure to a high density lipoprotein preparation or a proteinpolysaccharide preparation was without appreciable benefit. Use of blood from subjects receiving aspirin resulted in enhanced blood compatibility in the test system as did use of heparin. Use of Warfarin or dextran did not appear to enhance blood compatibility of test surfaces under the conditions of this test system. Dialysis membranes and tubing which formed parts of the test system were examined by scanning and transmission electron microscopy in control tests and in tests for effects of proteins and antithrombotic agents. ImagesFig 5Fig 6Fig 7Fig 8Fig 9Fig 10Fig 11Fig 12Fig 13Fig 14Fig 1Fig 2Fig 3Fig 4 PMID:4825611

Channel electron multiplier compatibility with Viton and Apiezon-L vacuum grease

NASA Astrophysics Data System (ADS)

McComas, D. J.; Baldonado, J. R.; Bame, S. J.; Barraclough, B. L.

1987-12-01

Clean Viton and Viton coated with Apiezon-L vacuum grease were tested for their noncontaminating compatibility with channel electron multipliers (CEMs). The test setup and procedure were the same as those used previously in conjunction with CEM compatibility tests of certain epoxies, solder, and fluorocarbon polymer materials useful for construction of spaceflight sensors. While some CEM gain degradation was noted during exposure to Viton and Apiezon-L, the present tests indicate that, at least over instrument lifetimes of about 2 x 10 to the 12th counts, these materials should be suitable for (1) preflight space sensor testing systems, (2) hermetic seals for CEM-based space sensors, and (3) terrestrial CEM-based instrumentation.

AEOLUS mission: the latest preparations before launch

NASA Astrophysics Data System (ADS)

Culoma, A.; Elfving, A.; Meynart, R.; Straume, A.; Wernham, D.

2017-09-01

The European Space Agency is developing a direct detection Doppler Wind Lidar for measuring wind profiles from space. The main objective of Aeolus is to provide tropospheric and lower stratospheric wind profiles globally for the improvement of weather forecast on short and medium term. Aeolus data are expected to greatly contribute to weather and air quality monitoring and to scientific advances in atmospheric dynamics. The UV Lidar instrument, ALADIN, will deliver horizontally-projected single line-of-sight wind profiles from the Doppler shift of molecular and particle backscatter. The development of the AEOLUS mission passed a major milestone with the integration of the full instrument and its functional and performance tests in 2016 and a 6-month life test of the spare UV laser transmitter. The satellite has been assembled and has successfully been subjected to a programme of functional and environmental (vibration, acoustic, shock, EMC) tests. The preparation of thermal vacuum testing, including instrument performance in vacuum, is close to completion.

Compatibility testing of spacecraft materials and space-storable liquid propellants

NASA Technical Reports Server (NTRS)

Constantino, L. L.; Denson, J. R.; Krishnan, C. S.; Toy, A.

1974-01-01

Compatibility measurements were made for aluminum 2219-T87 alloy and titanium 6Al-4V alloy in the presence of liquid fluorine and flox. Results of post test characterization after exposure durations of 61 and 70 weeks are presented. Results of the total test program are analyzed.

78 FR 28733 - Medical Devices; General Hospital and Personal Use Monitoring Devices; Classification of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-16

... Toxicology Testing. Labeling (dose limits). Electromagnetic incompatibility........ Electromagnetic... analysis and nonclinical testing must validate electromagnetic compatibility performance, wireless... electromagnetic compatibility performance, wireless performance, and electrical safety; and (4) Labeling must...

Physical and Chemical Compatibility of Injectable Acetaminophen During Simulated Y-Site Administration

PubMed Central

Anderson, Collin; Boehme, Sabrina; Ouellette, Jacquelyn; Stidham, Chanelle; MacKay, Mark

2014-01-01

Purpose: The physical and chemical compatibility of intravenous acetaminophen with commonly administered injectable medications was evaluated. Methods: Simulated Y-site evaluation was accomplished by mixing 2 mL of acetaminophen (10 mg/mL) with 2 mL of an alternative intravenous medication and subsequently storing the mixture in a polypropylene syringe for 4 hours. The aliquot solutions were visually inspected and evaluated for crystal content at 4 hours by infusing 4 mL of the medication mixture through a 0.45-μm nitrocellulose filter disc. Medication mixtures that were selected for chemical stability testing were analyzed by high-performance liquid chromatography at 0, 1, and 4 hours using a Zorbax Eclipse Plus C18, 4.6 x 100 mm, 3.5-μm column for separation of analytes with subsequent diode-array detection. Medications were considered chemically compatible if the concentrations of all components were >90% of the original concentrations during the 4 hour simulated Y-site compatibility test. Results: U.S. Pharmacopeial Convention (USP) standards for physical particle counts were met for acetaminophen injection (10 mg/mL) when combined with cefoxitin, ceftriaxone, clindamycin, dexamethasone, diphenhydramine, dolasetron, fentanyl, granisetron, hydrocortisone, hydromorphone, ketorolac, meperidine, methylprednisolone, midazolam, morphine, nalbuphine, ondansetron, piperacillin/tazobactam, ranitidine, and vancomycin. Injectable acetaminophen is incompatible with acyclovir and diazepam and therefore should not be administered concomitantly with either of these products. Further testing confirmed the chemical compatibility of acetaminophen with ceftriaxone, diphenhydramine, granisetron, ketorolac, nalbuphine, ondansetron, piperacillin/tazobactam, and vancomycin. Conclusion: All medications tested with acetaminophen were physically compatible except for acyclovir and diazepam. All 8 medications tested for chemical compatibility with acetaminophen were stable over the 4 hour simulated Y-site administration study. PMID:24421562

Flammability, odor, offgassing, thermal vacuum stability, and compatibility with aerospace fluids of wire insulations

NASA Technical Reports Server (NTRS)

Hirsch, David; Johnson, Harry

1994-01-01

The NASA Lewis Research Center requested NASA Johnson Space Center White Sands Test Facility to conduct flammability, odor, offgassing, thermal vacuum stability, and compatibility tests with aerospace fluids of several wire insulations.

ARC EMCS Experiments (Seedling Growth-2) Experiment Status

NASA Technical Reports Server (NTRS)

Heathcote, David; Steele, Marianne

2015-01-01

Presentation of the status of the ARC ISS (International Space Station) Experiment, Seedling Growth-2 to the Payload Operations Investigator Working Group meeting at MSFC, Huntsville AL. The experiment employs the European Modular Cultivation System (ECMS).

The cornerstone of data warehousing for government applications

NASA Technical Reports Server (NTRS)

Kenbeek, Doug; Rothschild, Jack

1996-01-01

The purpose of this paper is to discuss data warehousing storage issues and the impact of EMC open storage technology for meeting the myriad of challenges government organizations face when building Decision Support/Data Warehouse system.

NCEP ENSEMBLE PRODUCTS

Science.gov Websites

://www.emc.ncep.noaa.gov/GEFS/ The links to the various Forecast Plots are listed under Experimental Data on the new GEFS page. This NCEP Ensemble Home Page is a collection of experimental analysis and forecast products

Uncertainties in stormwater runoff data collection from a small urban catchment, Southeast China.

PubMed

Huang, Jinliang; Tu, Zhenshun; Du, Pengfei; Lin, Jie; Li, Qingsheng

2010-01-01

Monitoring data are often used to identify stormwater runoff characteristics and in stormwater runoff modelling without consideration of their inherent uncertainties. Integrated with discrete sample analysis and error propagation analysis, this study attempted to quantify the uncertainties of discrete chemical oxygen demand (COD), total suspended solids (TSS) concentration, stormwater flowrate, stormwater event volumes, COD event mean concentration (EMC), and COD event loads in terms of flow measurement, sample collection, storage and laboratory analysis. The results showed that the uncertainties due to sample collection, storage and laboratory analysis of COD from stormwater runoff are 13.99%, 19.48% and 12.28%. Meanwhile, flow measurement uncertainty was 12.82%, and the sample collection uncertainty of TSS from stormwater runoff was 31.63%. Based on the law of propagation of uncertainties, the uncertainties regarding event flow volume, COD EMC and COD event loads were quantified as 7.03%, 10.26% and 18.47%.

Estimation of human emotions using thermal facial information

NASA Astrophysics Data System (ADS)

Nguyen, Hung; Kotani, Kazunori; Chen, Fan; Le, Bac

2014-01-01

In recent years, research on human emotion estimation using thermal infrared (IR) imagery has appealed to many researchers due to its invariance to visible illumination changes. Although infrared imagery is superior to visible imagery in its invariance to illumination changes and appearance differences, it has difficulties in handling transparent glasses in the thermal infrared spectrum. As a result, when using infrared imagery for the analysis of human facial information, the regions of eyeglasses are dark and eyes' thermal information is not given. We propose a temperature space method to correct eyeglasses' effect using the thermal facial information in the neighboring facial regions, and then use Principal Component Analysis (PCA), Eigen-space Method based on class-features (EMC), and PCA-EMC method to classify human emotions from the corrected thermal images. We collected the Kotani Thermal Facial Emotion (KTFE) database and performed the experiments, which show the improved accuracy rate in estimating human emotions.

Evaluating Stellarator Divertor Designs with EMC3

NASA Astrophysics Data System (ADS)

Bader, Aaron; Anderson, D. T.; Feng, Y.; Hegna, C. C.; Talmadge, J. N.

2013-10-01

In this paper various improvements of stellarator divertor design are explored. Next step stellarator devices require innovative divertor solutions to handle heat flux loads and impurity control. One avenue is to enhance magnetic flux expansion near strike points, somewhat akin to the X-Divertor concept in Tokamaks. The effect of judiciously placed external coils on flux deposition is calculated for configurations based on the HSX stellarator. In addition, we attempt to optimize divertor plate location to facilitate the external coil placement. Alternate areas of focus involve altering edge island size to elucidate the driving physics in the edge. The 3-D nature of stellarators complicates design and necessitates analysis of new divertor structures with appropriate simulation tools. We evaluate the various configurations with the coupled codes EMC3-EIRENE, allowing us to benchmark configurations based on target heat flux, impurity behavior, radiated power, and transitions to high recycling and detached regimes. Work supported by DOE-SC0006103.

Epithelial-myoepithelial carcinoma of floor of mouth: A case report with cytological, histological and immunohistochemical correlation

PubMed Central

Mohanty, Sujata; Pathak, Himani

2014-01-01

A 61-year-old female presented with a 3-year-old swelling in the right floor of mouth. Clinical examination and fine needle aspiration cytology suggested a benign lesion. The mass was excised locally along with the involved sublingual and deep part of submandibular gland and duct. Post-operative histopathological examination revealed features of pleomorphic adenoma. However, on revision of histological sections, features were predominantly of a rare malignancy of the salivary glands, epithelial-myoepithelial carcinoma (EMC), along with focal areas of adenoid cystic carcinoma (Ad CC). The tumor was p-63, s-100 and smooth muscle actin positive but C-kit was negative, which ruled out Ad CC and the possibility of a hybrid carcinoma. The aim of this article is to describe a rare case of EMC in the floor of mouth and the confusing cytological picture that it created. PMID:25937734

Epithelial-myoepithelial carcinoma of floor of mouth: A case report with cytological, histological and immunohistochemical correlation.

PubMed

Mohanty, Sujata; Pathak, Himani

2014-01-01

A 61-year-old female presented with a 3-year-old swelling in the right floor of mouth. Clinical examination and fine needle aspiration cytology suggested a benign lesion. The mass was excised locally along with the involved sublingual and deep part of submandibular gland and duct. Post-operative histopathological examination revealed features of pleomorphic adenoma. However, on revision of histological sections, features were predominantly of a rare malignancy of the salivary glands, epithelial-myoepithelial carcinoma (EMC), along with focal areas of adenoid cystic carcinoma (Ad CC). The tumor was p-63, s-100 and smooth muscle actin positive but C-kit was negative, which ruled out Ad CC and the possibility of a hybrid carcinoma. The aim of this article is to describe a rare case of EMC in the floor of mouth and the confusing cytological picture that it created.

Molded underfill (MUF) encapsulation for flip-chip package: A numerical investigation

NASA Astrophysics Data System (ADS)

Azmi, M. A.; Abdullah, M. K.; Abdullah, M. Z.; Ariff, Z. M.; Saad, Abdullah Aziz; Hamid, M. F.; Ismail, M. A.

2017-07-01

This paper presents the numerical simulation of epoxy molding compound (EMC) filling in multi flip-chip packages during encapsulation process. The empty and a group flip chip packages were considered in the mold cavity in order to study the flow profile of the EMC. SOLIDWORKS software was used for three-dimensional modeling and it was incorporated into fluid analysis software namely as ANSYS FLUENT. The volume of fluid (VOF) technique was used for capturing the flow front profiles and Power Law model was applied for its rheology model. The numerical result are compared and discussed with previous experimental and it was shown a good conformity for model validation. The prediction of flow front was observed and analyzed at different filling time. The possibility and visual of void formation in the package is captured and the number of flip-chip is one factor that contributed to the void formation.

Characteristics of the event mean concentration (EMC) from rainfall runoff on an urban highway.

PubMed

Lee, Ju Young; Kim, Hyoungjun; Kim, Youngjin; Han, Moo Young

2011-04-01

The purpose of this study was to investigate the characterization of the event mean concentration (EMC) of runoff during heavy precipitation events on highways. Highway runoff quality data were collected from the 7th highway, in South Korea during 2007-2009. The samples were analyzed for runoff quantity and quality parameters such as COD(cr), TSS, TPHs, TKN, NO₃, TP, PO₄ and six heavy metals, e.g., As, Cu, Cd, Ni, Pb and Zn. Analysis of resulting hydrographs and pollutant graphs indicates that the peak of the pollutant concentrations in runoff occurs 20 min after the first rainfall runoff occurrence. The first flush effect depends on the preceding dry period and the rainfall intensity. The results of this study can be used as a reference for water quality management of urban highways. Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.

Photo nuclear energy loss term for muon-nucleus interactions based on xi scaling model of QCD

NASA Technical Reports Server (NTRS)

Roychoudhury, R.

1985-01-01

Extensive air showers (EMC) experiments discovered a significant deviation of the ratio of structure functions of iron and deuteron from unity. It was established that the quark parton distribution in nuclei are different from the corresponding distribution in the nucleus. It was examined whether these results have an effect on the calculation of photo nucleus energy loss term for muon-nucleus nuclear interaction. Though the EMC and SLAC data were restricted to rather large q sq region it is expected that the derivation would persist even in the low q sq domain. For the ratio of iron and deuteron structure function a rather naive least square fit of the form R(x) = a + bx was taken and it is assumed that the formula is valid for the whole q sq region the absence of any knowledge of R(x) for small q sq.

Oxygen Compatibility Testing of Composite Materials

NASA Technical Reports Server (NTRS)

Graf, Neil A.; Hudgins, Richard J.; McBain, Michael

2000-01-01

The development of polymer composite liquid oxygen LO2 tanks is a critical step in creating the next generation of launch vehicles. Future launch vehicles need to minimize the gross liftoff weight (GLOW), which is possible due to the 25%-40% reduction in weight that composite materials could provide over current aluminum technology. Although a composite LO2 tank makes these weight savings feasible, composite materials have not historically been viewed as "LO2 compatible." To be considered LO2 compatible, materials must be selected that will resist any type of detrimental, combustible reaction when exposed to usage environments. This is traditionally evaluated using a standard set of tests. However, materials that do not pass the standard tests can be shown to be safe for a particular application. This paper documents the approach and results of a joint NASA/Lockheed Martin program to select and verify LO2 compatible composite materials for liquid oxygen fuel tanks. The test approach developed included tests such as mechanical impact, particle impact, puncture, electrostatic discharge, friction, and pyrotechnic shock. These tests showed that composite liquid oxygen tanks are indeed feasible for future launch vehicles.

EMC problems on board the remote sensing and communications satellites equipped with electric propulsions

NASA Astrophysics Data System (ADS)

Plokhikh, A.; Vazhenin, N.; Soganova, G.

Wide application of electric propulsions (EP) as attitude control and orbit correction thrusters for a numerous class of satellites (remote sensing and communications satellites including) imposes new problems before the developers in meeting the electromagnetic compatibility requirements on board these satellites. This is connected with the fact that any EP is a source of interference broad-band emission reaching, as a rule, frequency ranges used by on-board radio systems designed for remote sensing and communications. In this case, reliable joint operation should be secured for the highly sensitive on -board radio receiving systems and sensors of remote sensing systems on one hand and EP on the other. In view of this, analysis is rather actual for the influence of EP interference emission upon the parameters and characteristics of modern remote sensing and communications systems. Procedures and results of typical operating characteristics calculation for the radio systems with the presence of operating EP on board are discussed in the paper on the basis of systematic approach with the following characteristics being among them: signal-to-noise ratio, range, data transmission rate, error probability, etc. EP effect is taken into account by the statistical analysis for the results of joint influence of valid signal and interference produced by EP upon the quality indices of communication systems and paths of the sensors being the parts of remote sensing systems. Test data for the measured EP interference characteristics were used for qualitative assessments. All necessary measurements were made by authors on the basis of the test procedure developed by them for assessing self- em ission of EP under ground conditions that may be used as a base for the certification of such measurements. Analysis was made on the basis of test data obtained and calculation procedures developed by authors for the EP influence upon the qualitative characteristics of remote sensing and communications radio systems that revealed the presence of destructive effect resulting in substantial decrease in maximum range and data transmission rate, as well as reduction of sensitivity for the sensors of remote sensing systems. Recommendations are given on the basis of analysis made for the optimization of radio systems and calibration of their sensors at a presence of electric propulsions on board the satellites.

Ground testing of Arabidopsis preservation protocol for the microarray analysis to be used in the ISS EMCS Multigen-2 experiment

NASA Astrophysics Data System (ADS)

Kittang, Ann-Iren; Kvaløy, Brita; Winge, Per; Iversen, Tor-Henning

2010-11-01

Gene expression analysis using microarrays has proved to be an important method in life science. The opportunity to grow higher plants on the International Space Station (ISS) opens up the possibility for gene expression profiling of plants grown in microgravity. The work presented focuses on how to meet the scientific requirements of plant growth and the sample preservation, given the technical and operational constraints associated with space research. The growth chamber (Multigen-2 Science Testing Unit) and a protocol suggested to be used in the European Modular Cultivation System (EMCS) Multigen-2 experiment on the ISS to grow and later preserve Arabidopsis seedlings, were tested on ground. The results showed that most of the plants developed normally. In order to avoid high population stress the number of seedlings per growth area should be reduced. The RNAlater preservation method to be used in the space experiment was compared with a quick freeze in Liquid Nitrogen (LN2). The RNA from samples preserved in RNAlater at room temperature for 24 h was slightly more degraded than the RNA from the LN2 preserved samples (RNA integrity number, RIN: 7.7 and 8.6, respectively). However, the RNA quality and quantity was satisfactory for microarray analysis. Of the genes analysed, 74 genes (0.28%) were significantly differentially expressed, most of them showing moderate to low regulation. Among the genes induced in the RNAlater preserved samples, three salt inducible transcription factors (ZAT10, SZF1 and SZF2) were identified, suggesting that the high salt concentration in RNAlater causes salt stress before the transcription stopped. In conclusion, the Multigen-2 preservation protocol tested here will allow for the genes regulated by microgravity in the space experiment to be revealed. The results do indicate that not all the biological processes are stopped instantly by the RNAlater. The limited diffusion indirectly caused by the microgravity may potentially result in a different degree of salt stress in the test compared to the 1 × g control during the space experiment. This has to be accounted for during the evaluation of the results. Since slightly degraded RNA was observed, further optimalisation of the preservation protocol will be performed.

Evaluation of accuracy of linear regression models in predicting urban stormwater discharge characteristics.

PubMed

Madarang, Krish J; Kang, Joo-Hyon

2014-06-01

Stormwater runoff has been identified as a source of pollution for the environment, especially for receiving waters. In order to quantify and manage the impacts of stormwater runoff on the environment, predictive models and mathematical models have been developed. Predictive tools such as regression models have been widely used to predict stormwater discharge characteristics. Storm event characteristics, such as antecedent dry days (ADD), have been related to response variables, such as pollutant loads and concentrations. However it has been a controversial issue among many studies to consider ADD as an important variable in predicting stormwater discharge characteristics. In this study, we examined the accuracy of general linear regression models in predicting discharge characteristics of roadway runoff. A total of 17 storm events were monitored in two highway segments, located in Gwangju, Korea. Data from the monitoring were used to calibrate United States Environmental Protection Agency's Storm Water Management Model (SWMM). The calibrated SWMM was simulated for 55 storm events, and the results of total suspended solid (TSS) discharge loads and event mean concentrations (EMC) were extracted. From these data, linear regression models were developed. R(2) and p-values of the regression of ADD for both TSS loads and EMCs were investigated. Results showed that pollutant loads were better predicted than pollutant EMC in the multiple regression models. Regression may not provide the true effect of site-specific characteristics, due to uncertainty in the data. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Phosphorus loads from different urban storm runoff sources in southern China: a case study in Wenzhou City.

PubMed

Zhou, Dong; Bi, Chun-Juan; Chen, Zhen-Lou; Yu, Zhong-Jie; Wang, Jun; Han, Jing-Chao

2013-11-01

Storm runoff from six types of underlying surface area during five rainfall events in two urban study areas of Wenzhou City, China was investigated to measure phosphorus (P) concentrations and discharge rates. The average event mean concentrations (EMCs) of total phosphorus (TP), total dissolved phosphorus (TDP), and particulate phosphorus (PP) ranged from 0.02 to 2.5 mg · L(-1), 0.01 to 0.48 mg · L(-1), and 0.02 to 2.43 mg · L(-1), respectively. PP was generally the dominant component of TP in storm runoff, while the major form of P varied over time, especially in roof runoff, where TDP made up the largest portion in the latter stages of runoff events. Both TP and PP concentrations were positively correlated with pH, total suspended solids (TSS), and biochemical oxygen demand (BOD)/chemical oxygen demand (COD) concentrations (p<0.01), while TDP was positively correlated with BOD/COD only (p<0.01). In addition, the EMCs of TP and PP were negatively correlated with maximum rainfall intensity (p<0.05), while the EMCs of TDP positively correlated with the antecedent dry weather period (p<0.05). The annual TP emission fluxes from the two study areas were 367.33 and 237.85 kg, respectively. Underlying surface type determined the TP and PP loadings in storm runoff, but regional environmental conditions affected the export of TDP more significantly. Our results indicate that the removal of particles from storm runoff could be an effective measure to attenuate P loadings to receiving water bodies.

Watershed and land use-based sources of trace metals in urban storm water.

PubMed

Tiefenthaler, Liesl L; Stein, Eric D; Schiff, Kenneth C

2008-02-01

Trace metal contributions in urban storm water are of concern to environmental managers because of their potential impacts on ambient receiving waters. The mechanisms and processes that influence temporal and spatial patterns of trace metal loading in urban storm water, however, are not well understood. The goals of the present study were to quantify trace metal event mean concentration (EMC), flux, and mass loading associated with storm water runoff from representative land uses; to compare EMC, flux, and mass loading associated with storm water runoff from urban (developed) and nonurban (undeveloped) watersheds; and to investigate within-storm and within-season factors that affect trace metal concentration and flux. To achieve these goals, trace metal concentrations were measured in 315 samples over 11 storm events in five southern California, USA, watersheds representing eight different land use types during the 2000 through 2005 storm seasons. In addition, 377 runoff samples were collected from 12 mass emission sites (end of watershed) during 15 different storm events. Mean flux at land use sites ranged from 24 to 1,238, 0.1 to 1,272, and 6 to 33,189 g/km(2) for total copper, total lead, and total zinc, respectively. Storm water runoff from industrial land use sites contained higher EMCs and generated greater flux of trace metals than other land use types. For all storms sampled, the highest metal concentrations occurred during the early phases of storm water runoff, with peak concentrations usually preceding peak flow. Early season storms produced significantly higher metal flux compared with late season storms at both mass emission and land use sites.

Heterogeneous Earth Structure, Deformation, and Slip During the 2010 Mw 7.2 El Mayor-Cucapah Earthquake from Geodetic Data

NASA Astrophysics Data System (ADS)

Huang, M. H.; Dickinson, H.; Fielding, E. J.; Sun, J.; Freed, A. M.; Burgmann, R.

2015-12-01

The 4th of April 2010 Mw 7.2 El Mayor-Cucapah (EMC) earthquake in Baja California and Sonora, Mexico has primarily right-lateral strike-slip motion and a minor normal slip component. The surface rupture extends about 120 km west of the boundary between the Pacific and the North American plates. The EMC event initiated near the center and ruptured bilaterally into an east-dipping strike-slip fault zone to the north and a west-dipping strike-slip zone to the south. Here we use geodetic measurements including GPS, InSAR (SAR interferometry), and sub-pixel offset measurements to characterize the fault slip during the EMC event. We use dislocation inversion methods to determine fault geometry as well as sub-fault slip distribution based on geodetic measurements. We find that assuming layered earth elastic structure increased the inferred deep slip (10-15 km depth) by up to 1.6 m (60%) compared to assuming a homogeneous elastic structure. Inferred slip was also strongly (up to 2 m) influenced by the choice of observational constraints used in the inversion. The choice of constraints also influenced the inverted seismic moment from Mw 7.20 to 7.26, and the difference is equivalent to a Mw 6.5 event. Our results show that the outcomes of coseismic inversions can vary greatly depending on the methodology, something that needs to be considered both for characterizing an earthquake and when using such results in subsequent studies of postseismic deformation.

Exploration of plant growth and development using the European Modular Cultivation System facility on the International Space Station.

PubMed

Kittang, A-I; Iversen, T-H; Fossum, K R; Mazars, C; Carnero-Diaz, E; Boucheron-Dubuisson, E; Le Disquet, I; Legué, V; Herranz, R; Pereda-Loth, V; Medina, F J

2014-05-01

Space experiments provide a unique opportunity to advance our knowledge of how plants respond to the space environment, and specifically to the absence of gravity. The European Modular Cultivation System (EMCS) has been designed as a dedicated facility to improve and standardise plant growth in the International Space Station (ISS). The EMCS is equipped with two centrifuges to perform experiments in microgravity and with variable gravity levels up to 2.0 g. Seven experiments have been performed since the EMCS was operational on the ISS. The objectives of these experiments aimed to elucidate phototropic responses (experiments TROPI-1 and -2), root gravitropic sensing (GRAVI-1), circumnutation (MULTIGEN-1), cell wall dynamics and gravity resistance (Cell wall/Resist wall), proteomic identification of signalling players (GENARA-A) and mechanism of InsP3 signalling (Plant signalling). The role of light in cell proliferation and plant development in the absence of gravity is being analysed in an on-going experiment (Seedling growth). Based on the lessons learned from the acquired experience, three preselected ISS experiments have been merged and implemented as a single project (Plant development) to study early phases of seedling development. A Topical Team initiated by European Space Agency (ESA), involving experienced scientists on Arabidopsis space research experiments, aims at establishing a coordinated, long-term scientific strategy to understand the role of gravity in Arabidopsis growth and development using already existing or planned new hardware. © 2014 German Botanical Society and The Royal Botanical Society of the Netherlands.

78 FR 35173 - Physical Medicine Devices; Reclassification of Stair-Climbing Wheelchairs

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-12

.... Electromagnetic interference: The device may interfere with the operation of other electrical devices or be... electromagnetic compatibility testing as well as characterization of speed/acceleration, battery longevity, and... electrical safety and electromagnetic compatibility of the device. Performance testing must demonstrate...

Delayed seismicity rate changes controlled by static stress transfer

USGS Publications Warehouse

Kroll, Kayla A.; Richards-Dinger, Keith B.; Dieterich, James H.; Cochran, Elizabeth S.

2017-01-01

On 15 June 2010, a Mw5.7 earthquake occurred near Ocotillo, California, in the Yuha Desert. This event was the largest aftershock of the 4 April 2010 Mw7.2 El Mayor-Cucapah (EMC) earthquake in this region. The EMC mainshock and subsequent Ocotillo aftershock provide an opportunity to test the Coulomb failure hypothesis (CFS). We explore the spatiotemporal correlation between seismicity rate changes and regions of positive and negative CFS change imparted by the Ocotillo event. Based on simple CFS calculations we divide the Yuha Desert into three subregions, one triggering zone and two stress shadow zones. We find the nominal triggering zone displays immediate triggering, one stress shadowed region experiences immediate quiescence, and the other nominal stress shadow undergoes an immediate rate increase followed by a delayed shutdown. We quantitatively model the spatiotemporal variation of earthquake rates by combining calculations of CFS change with the rate-state earthquake rate formulation of Dieterich (1994), assuming that each subregion contains a mixture of nucleation sources that experienced a CFS change of differing signs. Our modeling reproduces the observations, including the observed delay in the stress shadow effect in the third region following the Ocotillo aftershock. The delayed shadow effect occurs because of intrinsic differences in the amplitude of the rate response to positive and negative stress changes and the time constants for return to background rates for the two populations. We find that rate-state models of time-dependent earthquake rates are in good agreement with the observed rates and thus explain the complex spatiotemporal patterns of seismicity.

Delayed Seismicity Rate Changes Controlled by Static Stress Transfer

NASA Astrophysics Data System (ADS)

Kroll, Kayla A.; Richards-Dinger, Keith B.; Dieterich, James H.; Cochran, Elizabeth S.

2017-10-01

On 15 June 2010, a Mw5.7 earthquake occurred near Ocotillo, California, in the Yuha Desert. This event was the largest aftershock of the 4 April 2010 Mw7.2 El Mayor-Cucapah (EMC) earthquake in this region. The EMC mainshock and subsequent Ocotillo aftershock provide an opportunity to test the Coulomb failure hypothesis (CFS). We explore the spatiotemporal correlation between seismicity rate changes and regions of positive and negative CFS change imparted by the Ocotillo event. Based on simple CFS calculations we divide the Yuha Desert into three subregions, one triggering zone and two stress shadow zones. We find the nominal triggering zone displays immediate triggering, one stress shadowed region experiences immediate quiescence, and the other nominal stress shadow undergoes an immediate rate increase followed by a delayed shutdown. We quantitatively model the spatiotemporal variation of earthquake rates by combining calculations of CFS change with the rate-state earthquake rate formulation of Dieterich (1994), assuming that each subregion contains a mixture of nucleation sources that experienced a CFS change of differing signs. Our modeling reproduces the observations, including the observed delay in the stress shadow effect in the third region following the Ocotillo aftershock. The delayed shadow effect occurs because of intrinsic differences in the amplitude of the rate response to positive and negative stress changes and the time constants for return to background rates for the two populations. We find that rate-state models of time-dependent earthquake rates are in good agreement with the observed rates and thus explain the complex spatiotemporal patterns of seismicity.

DSOM - Decision Support for Operations and Maintenance - Application to a USMC Base Centralized Energy System.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meador, Richard J.; Hatley, Darrel D.

2004-06-01

PNNL DSOM technology coordinates efficient steam plant operation with EMCS and SCADA systems, providing generation support and automated load shedding to meet peak demand limits saving over $1M in two years.

Lithospheric Structure and Active Deformation in the Salton Trough from Coseismic and Postseismic Models of the 2010 Mw 7.2 El Mayor-Cucapah Earthquake

NASA Astrophysics Data System (ADS)

Fielding, E. J.; Huang, M. H.; Dickinson, H.; Freed, A. M.; Burgmann, R.; Gonzalez-Ortega, J. A.; Andronicos, C.

2016-12-01

The 4 April 2010 Mw 7.2 El Mayor-Cucapah (EMC) Earthquake ruptured about 120 km along several NW-striking faults to the west of the Cerro Prieto Fault in the Salton Trough of Baja California, Mexico. We analyzed interferometric synthetic aperture radar (SAR), SAR and optical pixel offsets, and continuous and campaign GPS data to optimize an EMC coseismic rupture model with 9 fault segments, which fits the complex structure of the faults. Coseismic slip inversion with a layered elastic model shows that largely right-lateral slip is confined to upper 10 km with strong variations along strike. Near-field GPS measures slip on a north-striking normal fault that ruptured at the beginning of the earthquake, previously inferred from seismic waveforms. EMC Earthquake postseismic deformation shows the Earth's response to the large coseismic stress changes. InSAR shows rapid shallow afterslip at the north and south ends of the main ruptures. Continuous GPS from the Plate Boundary Observatory operated by UNAVCO measures the first six years of postseismic deformation, extremely rapid near the rupture. Afterslip on faults beneath the coseismic rupture cannot explain far-field displacements that are best explained by viscoelastic relaxation of the lower crust and upper mantle. We built a viscoelastic 3D finite element model of the lithosphere and asthenosphere based on available data for the region with the EMC coseismic faults embedded inside. Coseismic slip was imposed on the model, allowed to relax for 5 years, and then compared to the observed surface deformation. Systematic exploration of the viscoelastic parameters shows that horizontal and vertical heterogeneity is required to fit the postseismic deformation. Our preferred viscoelastic model has weaker viscosity layers beneath the Salton Trough than adjacent blocks that are consistent with the inferred differences in the geotherms. Defining mechanical lithosphere as rocks that have viscosities greater than 10^19 Pa s (able to sustain stresses for more than 100 years), we infer the thickness of lithosphere beneath the Salton Trough to be 32 km and 65 km beneath the Peninsula Ranges to the west. These mechanical lithosphere-asthenosphere boundaries (LABs) are shallower than the observed seismic LABs, but probably better represent the strength of the blocks in this area.

75 FR 32943 - Food and Drug Administration Modernization Act of 1997: Modifications to the List of Recognized...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-10

... basic safety and essential performance--Collateral standard: Electromagnetic compatibility--Requirements... standard: Electromagnetic compatibility--Requirements and tests 5-34 5-53 IEC 60601-1-2 Third edition 2007... for basic safety and essential performance--Collateral standard: Electromagnetic compatibility...

An in vitro investigation into the physical properties of irreversible hydrocolloid alternatives.

PubMed

Patel, Rishi D; Kattadiyil, Mathew T; Goodacre, Charles J; Winer, Myron S

2010-11-01

A number of manufacturers have introduced new products that are marketed as alternatives to irreversible hydrocolloid impression materials. However, there is a paucity of laboratory and clinical research on these products compared to traditional irreversible hydrocolloid. The purpose of this study was to evaluate the detail reproduction, gypsum compatibility, and linear dimensional change of 3 recently introduced impression materials designed as alternatives to irreversible hydrocolloid. The tested materials were Position Penta Quick, Silgimix, and AlgiNot. An irreversible hydrocolloid impression material, Jeltrate Plus Antimicrobial, served as the control. The parameters of detail reproduction, gypsum compatibility, and linear dimensional change were tested in accordance with ANSI/ADA Specifications No. 18 and 19. The gypsum compatibility was tested using a type III stone (Microstone Golden) and a type IV stone (Die-Keen Green). The data were analyzed using the Kruskal-Wallis rank test and the Mann-Whitney U test (α=.05). The test materials demonstrated significantly (P<.001) better detail reproduction than the control material. Silgimix exhibited the best compatibility with Microstone, whereas AlgiNot and Position Penta Quick exhibited the best gypsum compatibility with Die-Keen. An incompatibility was observed over time between the Jeltrate control material and the Microstone gypsum material. For linear dimensional change, the mean dimension of the control material most closely approximated the distance between the lines on the test die, but it exhibited the greatest variability in measurements. All of the test materials exhibited linear dimensional change within the ADA's accepted limit of 1.0%. The 3 new impression materials exhibited better detail reproduction and less variability in linear dimensional change than the irreversible hydrocolloid control. Gypsum compatibility varied with the brand of gypsum used, with an incompatibility identified between the control material (Jeltrate Plus Antimicrobial) and Microstone related to surface changes observed over time. Copyright © 2010 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

The Influence of Modulated Signal Risetime in Flight Electronics Radiated Immunity Testing with a Mode-Stirred Chamber

NASA Technical Reports Server (NTRS)

Ely, Jay J.; Nguyen, Truong X.; Scearce, Stephen A.

2000-01-01

For electromagnetic immunity testing of an electronic system, it is desirable to demonstrate its functional integrity when exposed to the full range and intensity of environmental electromagnetic threats that may be encountered over its operational life. As part of this, it is necessary to show proper system operation when exposed to representative threat signal modulations. Modulated signal transition time is easily overlooked, but can be highly significant to system susceptibility. Radiated electromagnetic field immunity testing is increasingly being performed in Mode Stirred Chambers. Because the peak field vs. time relationship is affected by the operation of a reverberating room, it is important to understand how the room may influence any input signal modulation characteristics. This paper will provide insight into the field intensity vs. time relationship within the test environment of a mode stirred chamber. An understanding of this relationship is important to EMC engineers in determining what input signal modulation characteristics will be transferred to the equipment under test. References will be given for the development of this topic, and experimental data will be presented

A Single-Block TRL Test Fixture for the Cryogenic Characterization of Planar Microwave Components

NASA Technical Reports Server (NTRS)

Mejia, M.; Creason, A. S.; Toncich, S. S.; Ebihara, B. T.; Miranda, F. A.

1996-01-01

The High-Temperature-Superconductivity (HTS) group of the RF Technology Branch, Space Electronics Division, is actively involved in the fabrication and cryogenic characterization of planar microwave components for space applications. This process requires fast, reliable, and accurate measurement techniques not readily available. A new calibration standard/test fixture that enhances the integrity and reliability of the component characterization process has been developed. The fixture consists of 50 omega thru, reflect, delay, and device under test gold lines etched onto a 254 microns (0.010 in) thick alumina substrate. The Thru-Reflect-Line (TRL) fixture was tested at room temperature using a 30 omega, 7.62 mm (300 mil) long, gold line as a known standard. Good agreement between the experimental data and the data modelled using Sonnet's em(C) software was obtained for both the return (S(sub 11)) and insertion (S( 21)) losses. A gold two-pole bandpass filter with a 7.3 GHz center frequency was used as our Device Under Test (DUT), and the results compared with those obtained using a Short-Open-Load-Thru (SOLT) calibration technique.

Effects of the thermal sterilization procedure on polymeric products

NASA Technical Reports Server (NTRS)

Campbell, B. A.; Kalfayan, S. H.

1971-01-01

Properties of samples are tested, after thermal exposure, and values are compared with unexposed samples. Thermal stability or compatibility ratings of formulated or compounded organic polymers using trade names are made and degree of change in measured properties is assessed. Products are rated compatible, marginal, or not compatible.

NCEP HYSPLIT SMOKE & DUST Verification. NOAA/NWS/NCEP/EMC

Science.gov Websites

April May June July August Summer September October November December Prod vs Para Summer 2013 CA/MX Hawaii All regions PROD run All regions PARA run Select averaged hour: 1 hr average Select forecast four

National Centers for Environmental Prediction

Science.gov Websites

...).t00z.pgrb2(a/b)f24 The examples of files given above are pressure grib files that also contain flux and ) 5830 University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page generated:Sunday

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allcorn, Eric

A standard electrolyte mixture of 1.2M LiPF6 in EC:EMC (Gen2) was prepared and combined with various weight percentages of the BFR additive Tribromoneopentyl Alcohol (TBNPA) of the values 1, 2, 5, 10, 20, 30, and 40 wt.%. The additive amounts of 1,2,5,10, and 20 wt.% TBNPA were visually fully dissolved within 10 minutes of mixing with the Gen2 electrolyte while the 30 wt.% mixture showed full dissolution after 24 hours and the 40 wt.% mixture after 36 hours. A baseline of Gen2 electrolyte with no TBNPA was also included in testing as a baseline. Once the mixtures were fully dissolved,more » electrolyte conductivity was carried out on prepared samples of <1mL using a tee-cell with glassy carbon electrodes. The tests were conducted with a Solartron potentiostat and frequency response analyzer with a voltage amplitude of 5mV and frequency range from 1 Hz to 100 kHz. Each mixture was tested at room temperature (~25°C).« less

Materials Compatibility Testing in RSRM ODC: Free Cleaner Selection

NASA Technical Reports Server (NTRS)

Keen, Jill M.; Sagers, Neil W.; McCool, Alex (Technical Monitor)

2001-01-01

Government regulations have mandated production phase-outs of a number of solvents, including 1,1,1-trichloroethane, an ozone-depleting chemical (ODC). This solvent was used extensively in the production of the Reusable Solid Rocket Motors (RSRMs) for the Space Shuttle. Many tests have been performed to identify replacement cleaners. One major area of concern in the selection of a new cleaner has been compatibility. Some specific areas considered included cleaner compatibility with non-metallic surfaces, painted surfaces, support materials such as gloves and wipers as well as corrosive properties of the cleaners on the alloys used on these motors. The intent of this paper is to summarize the test logic, methodology, and results acquired from testing the many cleaner and material combinations.

78 FR 14015 - Medical Devices; Exemption From Premarket Notification; Class II Devices; Powered Patient Transport

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-04

... for Safety--Collateral Standard: Electromagnetic Compatibility--Requirements and Tests,'' and ASME A18.1 ``Safety Standard for Platform Lifts and Stairway Chair Lifts'') must validate electromagnetic...: Electromagnetic Compatibility--Requirements and Tests,'' and ASME A18.1 ``Safety Standard for Platform Lifts and...

Electromagnetic compatibility test report for the tethered satellite data acquisition and control assembly

NASA Astrophysics Data System (ADS)

Hoskins, Douglas; Snead, Robert

1988-05-01

This report details the results of an electromagnetic compatibility test on the SCI Systems Data Acquisition and Control Assembly (DACA). This assembly is an electronic processor which controls the central communication link from the Tethered Satellite System (TSS) to the Space Transportation System Orbiter Space Shuttle.

Conductive cotton prepared by polyaniline in situ polymerization using laccase.

PubMed

Zhang, Ya; Dong, Aixue; Wang, Qiang; Fan, Xuerong; Cavaco-Paulo, Artur; Zhang, Ying

2014-09-01

The high-redox-potential catalyst laccase, isolated from Aspergillus, was first used as a biocatalyst in the oxidative polymerization of water-soluble conductive polyaniline, and then conductive cotton was prepared by in situ polymerization under the same conditions. The polymerization of aniline was performed in a water dispersion of sodium dodecylbenzenesulfonate (SDBS) micellar solution with atmospheric oxygen serving as the oxidizing agent. This method is ecologically clean and permits a greater degree of control over the kinetics of the reaction. The conditions for polyaniline synthesis were optimized. Characterizations of the conducting polyaniline and cotton were carried out using Fourier transform infrared spectroscopy, UV-vis spectroscopy, cyclic voltammetry, the fabric induction electrostatic tester, and the far-field EMC shielding effectiveness test fixture.

Abuse Response of 18650 Li-Ion Cells with Different Cathodes Using EC:EMC/LiPF6 and EC:PC:DMC/LiPF6 Electrolytes

DOE PAGES

Roth, Emmanuel Peter

2008-01-01

We report Lithium-Ion batteries are being considered as a high-energy density replacement for Nickel Metal Hydride (NiMH) batteries in Hybrid Electric Vehicles (HEVs) and in the new Plug-In Hybrids (PHEVs). Although these cells can result in significant reduction in weight and volume, they have several safety related issues that still need to be addressed. We report here on the thermal response of Li-ion cells specifically assembled in our laboratory to test new materials, electrolytes and additives. Finally, improvements in the thermal abuse tolerance of cells are reported and discussed in terms of the need for overall battery system safety.

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar (CFS) HURRICANE WEATHER RESEARCH and FORECASTING (HWRF) GLOBAL ENSEMBLE FORECAST SYSTEM (GEFS) NATIONAL Climate Prediction (NCWCP) 5830 University Research Court College Park, MD 20740 Page Author: EMC

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar Observing system Research and Predictability EXperiment (THORPEX) Targeted Obs Targeted Observations Cyclone University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page generated:Sunday, 27-May

49 CFR Appendix B to Part 173 - Procedure for Testing Chemical Compatibility and Rate of Permeation in Plastic Packaging and...

Code of Federal Regulations, 2014 CFR

2014-10-01

... Rate of Permeation in Plastic Packaging and Receptacles B Appendix B to Part 173 Transportation Other..., App. B Appendix B to Part 173—Procedure for Testing Chemical Compatibility and Rate of Permeation in... °C. (64 °F.) b. Test Method 2: 28 days at a temperature no lower than 50 °C. (122 °F.) c. Test Method...

A novel bifunctional metabolizable linker for the conjugation of antibodies with radionuclides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arano, Y.; Matsushima, H.; Tagawa, M.

1991-03-01

A novel heterogeneous bifunctional reagent containing an ester bond, N-((4-(2-maleimidoethoxy)-succinyl)oxy)succinimide (MESS), was designed and synthesized for the conjugation of antibodies with the gallium-67 (67Ga) chelate of succinyldeferoxamine (SDF) via the ester bond. MESS was synthesized by the acylation of N-(2-hydroxyethyl)maleimide with succinic anhydride, followed by the activation of the resulting carboxylic acid to a succinimido ester. MESS possesses a maleimide group for protein conjugation and an active ester group for deferoxamine (DFO) coupling, and the two functional groups are linked via ester bonding. Conjugation of 67Ga-SDF with nonspecific human IgG was performed by reacting freshly thiolated IgG with the reactionmore » product of MESS and DFO, followed by 67Ga labeling of the resulting conjugate using GaCl3 (67Ga-DFO-MESS-IgG). For comparison, 67Ga-DFO conjugated nonspecific human IgG with a nonmetabolizable linkage was synthesized under the same conjugation conditions as those for 67Ga-DFO-MESS-IgG, using a nonmetabolizable heterogenous bifunctional reagent (N-((6-maleimidocaproyl)oxy)succinimide, EMCS) instead of MESS (67Ga-DFO-EMCS-IgG). HPLC size-exclusion chromatography of both preparations showed a single radioactivity and UV peak corresponding to the intact IgG. Generation of 67Ga-SDF from the 67Ga-DFO-MESS-IgG was demonstrated by reverse-phase HPLC analysis and cellulose acetate electrophoresis after the incubation of 67Ga-DFO-MESS-IgG in a buffered solution containing carboxyesterase. After injection of 67Ga-DFO-MESS-IgG into mice, faster radioactivity clearance from the blood and less radioactivity accumulation in the liver, kidney, and spleen was noted than when 67Ga-DFO-EMCS-IgG was injected.« less

A network approach to assessing cognition in disorders of consciousness(e–Pub ahead of print)(CME)

PubMed Central

Rodriguez Moreno, D.; Schiff, N.D.; Giacino, J.; Kalmar, K.; Hirsch, J.

2010-01-01

Objective: Conventional assessments of consciousness rely on motor responses to indicate awareness. However, overt behaviors may be absent or ambiguous in patients with disorders of consciousness (DOC) resulting in underrating capacity for cognition. fMRI during a silent picture-naming task was evaluated as an indicator of command following when conventional methods are not sufficient. Methods: A total of 10 patients with and without conventional evidence of awareness, who met diagnostic criteria for the minimally conscious state (MCS) (n = 5), vegetative state (VS) (n = 3), emerged from MCS (EMCS) (n = 1), and locked-in syndrome (LIS) (n = 1), participated in this observational fMRI study. Results: The LIS and EMCS patients engaged a complete network of essential language-related regions during the object-naming task. The MCS and 2 of the VS patients demonstrated both complete and partial preservation of the object-naming system. Patients who engaged a complete network scored highest on the Coma Recovery Scale-Revised. Conclusions: This study supports the view that fMRI during object naming can elicit brain activations in patients with DOC similar to those observed in healthy subjects during command following, and patients can be stratified by completeness of the engaged neural system. These results suggest that activity of the language network may serve as an indicator of high-level cognition and possibly volitional processes that cannot be discerned through conventional behavioral assessment alone. GLOSSARY BA = Brodmann area; BOLD = blood oxygenation level–dependent; CRS-R = Coma Recovery Scale-Revised; DOC = disorders of consciousness; EMCS = emerged from minimally conscious state; GFi(d) = dorsal inferior frontal gyrus; GFi(v) = ventral inferior frontal gyrus; hrf = hemodynamic response function; LIS = locked-in syndrome; MCS = minimally conscious state; preSMA = pre-supplementary motor area; STG = superior temporal gyrus; VS = vegetative state. PMID:20980667

Electronic medication complete communication strategy for opioid prescriptions in the emergency department: Rationale and design for a three-arm provider randomized trial.

PubMed

McCarthy, Danielle M; Courtney, D Mark; Lank, Patrick M; Cameron, Kenzie A; Russell, Andrea M; Curtis, Laura M; Kim, Kwang-Youn A; Walton, Surrey M; Montague, Enid; Lyden, Abbie L; Gravenor, Stephanie J; Wolf, Michael S

2017-08-01

Thousands of people die annually from prescription opioid overdoses; however there are few strategies to ensure patients receive medication risk information at the time of prescribing. To compare the effectiveness of the Emergency Department (ED) Electronic Medication Complete Communication (EMC 2 ) Opioid Strategy (with and without text messaging) to promote safe medication use and improved patient knowledge as compared to usual care. The ED EMC 2 Opioid Strategy consists of 5 automated components to promote safe medication use: 1) physician reminder to counsel, 2) inbox message sent on to the patient's primary care physician, 3) pharmacist message on the prescription to counsel, 4) MedSheet supporting prescription information, and 5) patient-centered Take-Wait-Stop wording of prescription instructions. This strategy will be assessed both with and without the addition of text messages via a three-arm randomized trial. The study will take place at an urban academic ED (annual volume>85,000) in Chicago, IL. Patients being discharged with a new prescription for hydrocodone-acetaminophen will be enrolled and randomized (based on their prescribing physician). The primary outcome of the study is medication safe use as measured by a demonstrated dosing task. Additionally actual safe use, patient knowledge and provider counseling will be measured. Implementation fidelity as well as costs will be reported. The ED EMC 2 Opioid Strategy embeds a risk communication strategy into the electronic health record and promotes medication counseling with minimal workflow disruption. This trial will evaluate the strategy's effectiveness and implementation fidelity as compared to usual care. This trial is registered on clinicaltrials.gov with identifier NCT02431793. Copyright © 2017 Elsevier Inc. All rights reserved.

Revisiting Nuclear Thermal Propulsion for Human Mars Exploration

NASA Technical Reports Server (NTRS)

Percy, Thomas K.; Rodriguez, Mitchell

2017-01-01

Nuclear Thermal Propulsion (NTP) has long been considered as a viable in-space transportation alternative for delivering crew and cargo to the Martian system. While technology development work in nuclear propulsion has continued over the year, general interest in NTP propulsion applications has historically been tied directly to the ebb and flow of interest in sending humans to explore Mars. As far back as the 1960’s, plans for NTP-based human Mars exploration have been proposed and periodically revisited having most recently been considered as part of NASA Design Reference Architecture (DRA) 5.0. NASA has been investigating human Mars exploration strategies tied to its current Journey to Mars for the past few years however, NTP has only recently been added into the set of alternatives under consideration for in-space propulsion under the Mars Study Capability (MSC) team, formerly the Evolvable Mars Campaign (EMC) team. The original charter of the EMC was to find viable human Mars exploration approaches that relied heavily on technology investment work already underway, specifically related to the development of large Solar Electric Propulsion (SEP) systems. The EMC team baselined several departures from traditional Mars exploration ground rules to enable these types of architectures. These ground rule changes included lower energy conjunction class trajectories with corresponding longer flight times, aggregation of mission elements in cis-Lunar space rather than Low Earth Orbit (LEO) and, in some cases, the pre-deployment of Earth return propulsion systems to Mars. As the MSC team continues to refine the in-space transportation trades, an NTP-based architecture that takes advantage of some of these ground rule departures is being introduced.

Mars Surface Systems Common Capabilities and Challenges for Human Missions

NASA Technical Reports Server (NTRS)

Toups, Larry; Hoffman, Stephen J.; Watts, Kevin

2016-01-01

This paper describes the current status of common systems and operations as they are applied to actual locations on Mars that are representative of Exploration Zones (EZ) - NASA's term for candidate locations where humans could land, live and work on the martian surface. Given NASA's current concepts for human missions to Mars, an EZ is a collection of Regions of Interest (ROIs) located within approximately 100 kilometers of a centralized landing site. ROIs are areas that are relevant for scientific investigation and/or development/maturation of capabilities and resources necessary for a sustainable human presence. An EZ also contains a habitation site that will be used by multiple human crews during missions to explore and utilize the ROIs within the EZ. The Evolvable Mars Campaign (EMC), a description of NASA's current approach to these human Mars missions, assumes that a single EZ will be identified within which NASA will establish a substantial and durable surface infrastructure that will be used by multiple human crews. The process of identifying and eventually selecting this single EZ will likely take many years to finalized. Because of this extended EZ selection process it becomes important to evaluate the current suite of surface systems and operations being evaluated for the EMC as they are likely to perform at a variety of proposed EZ locations and for the types of operations - both scientific and development - that are proposed for these candidate EZs. It is also important to evaluate proposed EZs for their suitability to be explored or developed given the range of capabilities and constraints for the types of surface systems and operations being considered within the EMC.

An Improved Approach for Analyzing the Oxygen Compatibility of Solvents and other Oxygen-Flammable Materials for Use in Oxygen Systems

NASA Technical Reports Server (NTRS)

Harper, Susan A.; Juarez, Alfredo; Peralta, Stephen F.; Stoltzfus, Joel; Arpin, Christina Pina; Beeson, Harold D.

2016-01-01

Solvents used to clean oxygen system components must be assessed for oxygen compatibility, as incompatible residue or fluid inadvertently left behind within an oxygen system can pose a flammability risk. The most recent approach focused on solvent ignition susceptibility to assess the flammability risk associated with these materials. Previous evaluations included Ambient Pressure Liquid Oxygen (LOX) Mechanical Impact Testing (ASTM G86) and Autogenous Ignition Temperature (AIT) Testing (ASTM G72). The goal in this approach was to identify a solvent material that was not flammable in oxygen. As environmental policies restrict the available options of acceptable solvents, it has proven difficult to identify one that is not flammable in oxygen. A more rigorous oxygen compatibility approach is needed in an effort to select a new solvent for NASA applications. NASA White Sands Test Facility proposed an approach that acknowledges oxygen flammability, yet selects solvent materials based on their relative oxygen compatibility ranking, similar to that described in ASTM G63-99. Solvents are selected based on their ranking with respect to minimal ignition susceptibility, damage and propagation potential, as well as their relative ranking when compared with other solvent materials that are successfully used in oxygen systems. Test methods used in this approach included ASTM G86 (Ambient Pressure LOX Mechanical Impact Testing and Pressurized Gaseous Oxygen (GOX) Mechanical Impact Testing), ASTM G72 (AIT Testing), and ASTM D240 (Heat of Combustion (HOC) Testing). Only four solvents were tested through the full battery of tests for evaluation of oxygen compatibility: AK-225G as a baseline comparison, Solstice PF, L-14780, and Vertrel MCA. Baseline solvent AK-225G exhibited the lowest HOC and highest AIT of solvents tested. Nonetheless, Solstice PF, L-14780, and Vertrel MCA HOCs all fell well within the range of properties that are associated with proven oxygen system materials. Tested AITs for these solvents fell only slightly lower than the AIT for the proven AK-225G solvent. Based on these comparisons in which solvents exhibited properties within those ranges seen with proven oxygen system materials, it is believed that Solstice PF, L-14780, and Vertrel MCA would perform well with respect to oxygen compatibility.

A Laboratory Exercise for Compatibility Testing of Hazardous Wastes in an Environmental Analysis Course.

ERIC Educational Resources Information Center

Chang, J. C.; And Others

1986-01-01

Discusses a new program at the University of Michigan in hazardous waste management. Describes a laboratory demonstration that deals with the reactivity and potential violence of several reactions that may be encountered on a hazardous waste site. Provides criteria for selecting particular compatibility testing methods. (TW)

The compatibility of consumer DLP projectors with time-sequential stereoscopic 3D visualisation

NASA Astrophysics Data System (ADS)

Woods, Andrew J.; Rourke, Tegan

2007-02-01

A range of advertised "Stereo-Ready" DLP projectors are now available in the market which allow high-quality flickerfree stereoscopic 3D visualization using the time-sequential stereoscopic display method. The ability to use a single projector for stereoscopic viewing offers a range of advantages, including extremely good stereoscopic alignment, and in some cases, portability. It has also recently become known that some consumer DLP projectors can be used for timesequential stereoscopic visualization, however it was not well understood which projectors are compatible and incompatible, what display modes (frequency and resolution) are compatible, and what stereoscopic display quality attributes are important. We conducted a study to test a wide range of projectors for stereoscopic compatibility. This paper reports on the testing of 45 consumer DLP projectors of widely different specifications (brand, resolution, brightness, etc). The projectors were tested for stereoscopic compatibility with various video formats (PAL, NTSC, 480P, 576P, and various VGA resolutions) and video input connections (composite, SVideo, component, and VGA). Fifteen projectors were found to work well at up to 85Hz stereo in VGA mode. Twenty three projectors would work at 60Hz stereo in VGA mode.

Compatibility and infectivity of a Cercospora rodmanii formulation with enhancing agents. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pennington, J.C.; Theriot, E.A.

1983-06-01

A formulation of the fungus Cercospora rodmanii Conway has been produced, as a biocontrol of waterhyacinth (Eichhornia crassipes (Mart.) Solms.). To ensure the most efficient germination of the formulation, 12 potential enhancing agents were tested for addition during the spray application. The agents were aspartic acid, glucose, glutamic acid, gum xanthan, nutrient agar, Ortho X-77 Spreader, Tween 20, Tween 60, Tween 80, sodium alginate, Super Slupper, and yeast extract. Compatibility of test agents and combinations of test agents with two lots of the formulation was determined in the laboratory. All combinations of test agents were compatible with both lots ofmore » the C. rodmanii formulation. The C. rodmanii formulation was sprayed with test agents on waterhyacinth pseudolaminae. Damage was monitored each week for 8 weeks by assigning a disease index to each original and new pseudolaminae. No spots having characteristics suggestive of C. rodmanii infection were observed at any time during the study. Lack of infectivity could be remedied by isolating a virulent strain of C. rodmanii from the field. Agents determined to be compatible in this study could then be reexamined for enhancing infectivity on a virulent C. rodmanii formulation. 14 references, 2 figures, 5 tables.« less

Lopez-Alegria performs EMCS-EC replace activity in Destiny laboratory module

NASA Image and Video Library

2006-12-29

ISS014-E-10647 (29 Dec. 2006) --- Astronaut Michael E. Lopez-Alegria, Expedition 14 commander and NASA space station science officer, performs the European Modular Cultivation System (EMSC) -- Experiment Container (EC) replacement in the Destiny laboratory of the International Space Station.

Lopez-Alegria performs EMCS-EC replace activity in Destiny laboratory module

NASA Image and Video Library

2006-12-29

ISS014-E-10639 (29 Dec. 2006) --- Astronaut Michael E. Lopez-Alegria, Expedition 14 commander and NASA space station science officer, performs the European Modular Cultivation System (EMSC) -- Experiment Container (EC) replacement in the Destiny laboratory of the International Space Station.

NCEP Air Quality Forecast(AQF) Verification. NOAA/NWS/NCEP/EMC

Science.gov Websites

Southwest Desert All regions PROD All regions PARA Select averaged hour: 8 hr sfc average 1 hr sfc average Select forecast four: Diurnal period 01-24 hr by day 25-48 hr by day Select statistic type: BIAS RMSE

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar Cycle) and the High-Resolution Rapid Refresh (HRRR) was developed at NOAA's Earth System Research Prediction (NCWCP) 5830 University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page

A Measurement of Neutral B Mixing using Di-Lepton Events with the BaBar Detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gunawardane, Naveen

This thesis reports on a measurement of the neutral B meson mixing parameter, Δm d, at the BABAR experiment and the work carried out on the electromagnetic calorimeter (EMC) data acquisition (DAQ) system and simulation software.

Remedial/Reluctant Materials.

ERIC Educational Resources Information Center

Curriculum Review, 1978

1978-01-01

Eight kits or series are reviewed: Headliners I (EMC Corporation); Pacemaker Bestsellers I and II (Fearon-Pitman); Rocket Reading (AIDS); Vistas (Houghton Mifflin); The New Action Unit (Scholastic); Superstars of Soil and Rock (Steck-Vaughn); Super A and Super B (SRA); and Shoptalk: Vocational Reading Skills (Allyn and Bacon). (SJL)

NCEP Global Aerosols Forecast. NOAA/NWS/NCEP/EMC

Science.gov Websites

Documentations Select Domain Global Regional Year: 2016 2017 2018 Month: Jan Feb Mar Apr May Jun Jul Aug Sep Oct 31 Select Field: Total AOD Total AOD Dust AOD Sea salt AOD Black carbon AOD POM AOD Sulfate AOD Get

Measurement of the nucleon structure function F 2 in the nuclear medium and evaluation of its moments

DOE PAGES

Osipenko, M.

2010-06-01

We report on the measurement of inclusive electron scattering off a carbon target performed with CLAS at Jefferson Laboratory. A combination of three different beam energies 1.161, 2.261 and 4.461 GeV allowed us to reach an invariant mass of the final-state hadronic system W ≈ 2.4 GeV with four-momentum transfers Q 2 ranging from 0.2 to 5 GeV 2. These data, together with previous measurements of the inclusive electron scattering off proton and deuteron, which cover a similar continuous two-dimensional region of Q 2 and Bjorken variable x, permit the study of nuclear modifications of the nucleon structure. By usingmore » these, as well as other world data, we evaluated the F 2 structure function and its moments. Using an OPE-based twist expansion, we studied the Q 2-evolution of the moments, obtaining a separation of the leading-twist and the total higher-twist terms. The carbon-to-deuteron ratio of the leading-twist contributions to the F 2 moments exhibits the well known EMC effect, compatible with that discovered previously in x-space. The total higher-twist term in the carbon nucleus appears, although with large systematic uncertainites, to be smaller with respect to the deuteron case for n < 7, suggesting partial parton deconfinement in nuclear matter. Lastly, we speculate that the spatial extension of the nucleon is changed when it is immersed in the nuclear medium.« less

Morphological and electrical properties of epoxy-based composites reinforced with exfoliated graphite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamberti, Patrizia; Spinelli, Giovanni, E-mail: gspinelli@unisa.it; Tucci, Vincenzo

An experimental study has been carried out to prepare and characterize epoxy/amine-based composites filled with different percentages of partially exfoliated graphite (i.e. pEG) particles having an exfoliation degree of 56% in order to analyze the effect of the filler amounts on the electrical properties of the resulting nanocomposites. Moreover, in order to fully investigate the direct relationship between the physical properties of the employed filler and the results of the electrical characterization, a structural and morphological characterization of the pEG samples is carried out by means of various type of analysis such as X-ray diffraction patterns, micro-Raman and Scanning Electronmore » Microscopy (SEM) images. The DC electrical characterization reveals a percolation thresholds (EPT) that falls in the range [2–3] wt% and an electrical conductivity of about 0.66 S/m at the highest filler loading (6.5 wt%). From the analysis of the percolative curve it is possible to derive the percolation law parameters and in particular the critical exponent t, whose value (i.e. 1.2) reflects an effective 2D organization of the percolating structure consistent with the type of filler used (2-dimensional). Finally, an extensive analysis concerning the electrical properties in the frequency domain has been carried out in order to evaluate the effectiveness of pEG-loaded composites in terms of electromagnetic interference compatibility (EMC) and their applicability as radar absorbers materials (RAMs).« less

Evaluation of Electromagnetic Fields in a Hospital for Safe Use of Electronic Medical Equipment.

PubMed

Ishida, Kai; Fujioka, Tomomi; Endo, Tetsuo; Hosokawa, Ren; Fujisaki, Tetsushi; Yoshino, Ryoji; Hirose, Minoru

2016-03-01

Establishment of electromagnetic compatibility is important in use of electronic medical equipment in hospitals. To evaluate the electromagnetic environment, the electric field intensity induced by electromagnetic radiation in broadcasting spectra coming from outside the hospital was measured in a new hospital building before any patients visited the hospital and 6 months after the opening of the hospital. Various incoming radio waves were detected on the upper floors, with no significant difference in measured levels before and after opening of the hospital. There were no cellphone terminal signals before the hospital opened, but these signals were strongly detected at 6 months thereafter. Cellphone base stations signals were strongly detected on the upper floors, but there were no signals at most locations in the basement and in the center of the building on the lower floors. A maximum electrical intensity of 0.28 V/m from cellphone base stations (2.1 GHz) was detected at the south end of the 2nd floor before the hospital opened. This value is lower than the EMC marginal value for general electronic medical equipment specified in IEC 60601-1-2 (3 V/m). Therefore, electromagnetic interference with electronic medical equipment is unlikely in this situation. However, cellphone terminal signals were frequently detected in non-base station signal areas. This is a concern, and understanding signal strength from cellphone base stations at a hospital is important for promotion of greater safety.

Bacterial Compatibility in Combined Inoculations Enhances the Growth of Potato Seedlings.

PubMed

Santiago, Christine D; Yagi, Shogo; Ijima, Motoaki; Nashimoto, Tomoya; Sawada, Maki; Ikeda, Seishi; Asano, Kenji; Orikasa, Yoshitake; Ohwada, Takuji

2017-03-31

The compatibility of strains is crucial for formulating bioinoculants that promote plant growth. We herein assessed the compatibility of four potential bioinoculants isolated from potato roots and tubers (Sphingomonas sp. T168, Streptomyces sp. R170, Streptomyces sp. R181, and Methylibium sp. R182) that were co-inoculated in order to improve plant growth. We screened these strains using biochemical tests, and the results obtained showed that R170 had the highest potential as a bioinoculant, as indicated by its significant ability to produce plant growth-promoting substances, its higher tolerance against NaCl (2%) and AlCl 3 (0.01%), and growth in a wider range of pH values (5.0-10.0) than the other three strains. Therefore, the compatibility of R170 with other strains was tested in combined inoculations, and the results showed that the co-inoculation of R170 with T168 or R182 synergistically increased plant weight over un-inoculated controls, indicating the compatibility of strains based on the increased production of plant growth promoters such as indole-3-acetic acid (IAA) and siderophores as well as co-localization on roots. However, a parallel test using strain R181, which is the same Streptomyces genus as R170, showed incompatibility with T168 and R182, as revealed by weaker plant growth promotion and a lack of co-localization. Collectively, our results suggest that compatibility among bacterial inoculants is important for efficient plant growth promotion, and that R170 has potential as a useful bioinoculant, particularly in combined inoculations that contain compatible bacteria.

Helminth Community Dynamics in Populations of Blue-Winged Teal (Anas discors) Using Two Distinct Migratory Corridors.

PubMed

Garvon, Jason M; Fedynich, Alan M; Peterson, Markus J; Pence, Danny B

2011-01-01

The influence of spatially distinct host subpopulations on helminth community structure and pattern was examined in a migratory avian host species. Forty helminth species represented by 24,082 individuals were collected from 184 blue-winged teal (Anas discors; BWT) from 2 primary migratory corridors in Florida (eastern migratory corridor; EMC) and Louisiana and Texas (western migratory corridor; WMC). Mean species richness was greater in BWT from the WMC (x̅±SE = 10.2 ± 0.3 species) than the EMC (8.6 ± 0.2). The helminth community from the WMC had higher abundances of 6 common/intermediate species. Corridor helminth communities were similar in species composition but less similar when incorporating abundances of those species. Overlapping distributions of phylogenetically related host species that share generalist helminth species across ecologically similar habitats seem to mitigate the isolating mechanisms that are necessary for the distinct coevolutionary pathways to develop between adjacent corridors.

A Gravitational, Mathematical Model for the Energy, Emitted Power and Longevity of the Sun and Stars that does not use E=mc^2

NASA Astrophysics Data System (ADS)

Morse Kingsley, James

2017-08-01

A gravitational mathematical model for the energy, radiated power and lifetime of the sun and stars is derived that does not use E=mc^2. The speed of solar flares, 200 to 1000km/sec is used to derive the surface temperature of the sun as 1.4(10^6)degrees K. Optical radiation results as gamma rays leave the sun's surface and traverse and lose energy to the ~10^6km of the sun's corona. The corona is a result of solar flares with a speed component of 424km/sec parallel to the sun's surface placing their atoms into gravitational orbit about the sun. The temperature, density, and pressure of the sun are derived as a function of r, i.e. the distance from the center of the sun. The complete article is chapter 11 of my text that can be found on my website www.jmkingsleyiii.info

Electricity: The Energy of Tomorrow (A "Life at the Frontiers of Energy Research" contest entry from the 2011 Energy Frontier Research Centers (EFRCs) Summit and Forum)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

"Electricity: the Energy of Tomorrow" was submitted by the Energy Materials Center at Cornell (emc2) to the "Life at the Frontiers of Energy Research" video contest at the 2011 Science for Our Nation's Energy Future: Energy Frontier Research Centers (EFRCs) Summit and Forum. Twenty-six EFRCs created short videos to highlight their mission and their work. emc2, an EFRC directed by Hector D. Abruna at Cornell University (lead) is a partnership between Cornell and Lawrence Berkeley National Laboratory. The Office of Basic Energy Sciences in the U.S. Department of Energy's Office of Science established the 46 Energy Frontier Research Centers (EFRCs)more » in 2009. These collaboratively-organized centers conduct fundamental research focused on 'grand challenges' and use-inspired 'basic research needs' recently identified in major strategic planning efforts by the scientific community. The overall purpose is to accelerate scientific progress toward meeting the nation's critical energy challenges.« less

Lithium ethylene dicarbonate identified as the primary product of chemical and electrochemical reduction of EC in 1.2 M LiPF6/EC:EMC electrolyte.

PubMed

Zhuang, Guorong V; Xu, Kang; Yang, Hui; Jow, T Richard; Ross, Philip N

2005-09-22

Lithium ethylene dicarbonate ((CH2OCO2Li)2) was chemically synthesized and its Fourier transform infrared (FTIR) spectrum was obtained and compared with that of surface films formed on Ni after cyclic voltammetry (CV) in 1.2 M lithium hexafluorophosphate (LiPF6)/ethylene carbonate (EC):ethyl methyl carbonate (EMC) (3:7, w/w) electrolyte and on metallic lithium cleaved in-situ in the same electrolyte. By comparison of IR experimental spectra with that of the synthesized compound, we established that the title compound is the predominant surface species in both instances. Detailed analysis of the IR spectrum utilizing quantum chemical (Hartree-Fock) calculations indicates that intermolecular association through O...Li...O interactions is very important in this compound. It is likely that the title compound in the passivation layer has a highly associated structure, but the exact intermolecular conformation could not be established on the basis of analysis of the IR spectrum.

Electricity: The Energy of Tomorrow (A "Life at the Frontiers of Energy Research" contest entry from the 2011 Energy Frontier Research Centers (EFRCs) Summit and Forum)

ScienceCinema

Abruna, Hector D. (Director, Energy Materials Center at Cornell); emc2 Staff

2017-12-09

'Electricity: the Energy of Tomorrow' was submitted by the Energy Materials Center at Cornell (emc2) to the 'Life at the Frontiers of Energy Research' video contest at the 2011 Science for Our Nation's Energy Future: Energy Frontier Research Centers (EFRCs) Summit and Forum. Twenty-six EFRCs created short videos to highlight their mission and their work. emc2, an EFRC directed by Hector D. Abruna at Cornell University (lead) is a partnership between Cornell and Lawrence Berkeley National Laboratory. The Office of Basic Energy Sciences in the U.S. Department of Energy's Office of Science established the 46 Energy Frontier Research Centers (EFRCs) in 2009. These collaboratively-organized centers conduct fundamental research focused on 'grand challenges' and use-inspired 'basic research needs' recently identified in major strategic planning efforts by the scientific community. The overall purpose is to accelerate scientific progress toward meeting the nation's critical energy challenges.

Global Molecular Analyses of Methane Metabolism in Methanotrophic Alphaproteobacterium, Methylosinus trichosporium OB3b. Part I: Transcriptomic Study

PubMed Central

Matsen, Janet B.; Yang, Song; Stein, Lisa Y.; Beck, David; Kalyuzhnaya, Marina G.

2013-01-01

Methane utilizing bacteria (methanotrophs) are important in both environmental and biotechnological applications, due to their ability to convert methane to multicarbon compounds. However, systems-level studies of methane metabolism have not been carried out in methanotrophs. In this work we have integrated genomic and transcriptomic information to provide an overview of central metabolic pathways for methane utilization in Methylosinus trichosporium OB3b, a model alphaproteobacterial methanotroph. Particulate methane monooxygenase, PQQ-dependent methanol dehydrogenase, the H4MPT-pathway, and NAD-dependent formate dehydrogenase are involved in methane oxidation to CO2. All genes essential for operation of the serine cycle, the ethylmalonyl-CoA (EMC) pathway, and the citric acid (TCA) cycle were expressed. PEP-pyruvate-oxaloacetate interconversions may have a function in regulation and balancing carbon between the serine cycle and the EMC pathway. A set of transaminases may contribute to carbon partitioning between the pathways. Metabolic pathways for acquisition and/or assimilation of nitrogen and iron are discussed. PMID:23565111

EMC3-EIRENE modelling of toroidally-localized divertor gas injection experiments on Alcator C-Mod

DOE PAGES

Lore, Jeremy D.; Reinke, M. L.; LaBombard, Brian; ...

2014-09-30

Experiments on Alcator C-Mod with toroidally and poloidally localized divertor nitrogen injection have been modeled using the three-dimensional edge transport code EMC3-EIRENE to elucidate the mechanisms driving measured toroidal asymmetries. In these experiments five toroidally distributed gas injectors in the private flux region were sequentially activated in separate discharges resulting in clear evidence of toroidal asymmetries in radiated power and nitrogen line emission as well as a ~50% toroidal modulation in electron pressure at the divertor target. The pressure modulation is qualitatively reproduced by the modelling, with the simulation yielding a toroidal asymmetry in the heat flow to the outermore » strike point. Finally, toroidal variation in impurity line emission is qualitatively matched in the scrape-off layer above the strike point, however kinetic corrections and cross-field drifts are likely required to quantitatively reproduce impurity behavior in the private flux region and electron temperatures and densities directly in front of the target.« less

Milliwatt Generator Project

NASA Astrophysics Data System (ADS)

Latimer, T. W.; Rinehart, G. H.

1992-05-01

This report covers progress on the Milliwatt Generator Project from April 1986 through March 1988. Activities included fuel processing and characterization, production of heat sources, fabrication of pressure-burst test units, compatibility studies, impact testing, and examination of surveillance units. The major task of the Los Alamos Milliwatt Generator Project is to fabricate MC2893A heat sources (4.0 W) for MC2730A radioisotope thermoelectric generators (RTG's) and MC3599 heat sources (4.5 W) for MC3500 RTG's. The MWG Project interfaces with the following contractors: Sandia National Laboratories, Albuquerque (designer); E.I. du Pont de Nemours and Co. (Inc.), Savannah River Plant (fuel); Monsanto Research Corporation, Mound Facility (metal hardware); and General Electric Company, Neutron Devices Department (RTG's). In addition to MWG fabrication activities, Los Alamos is involved in (1) fabrication of pressure-burst test units, (2) compatibility testing and evaluation, (3) examination of surveillance units, and (4) impact testing and subsequent examination of compatibility and surveillance units.

Hygrothermal Properties of Cross Laminated Timber and Moisture Response of Wood at High Relative Humidity

NASA Astrophysics Data System (ADS)

AlSayegh, George

Cross Laminated Timber (CLT) is a new wood-based material composed of cross laminated wood boards that form a structural panel. This study focuses on identifying the appropriate methods to determine the hygrothermal properties of CLTs fabricated with Canadian and European Lumber. The laboratory tests carried out in this study will help establish heat, air and moisture response properties to be used for hygrothermal simulation to assess the durability of CLTs in building envelope construction. Measurement of water vapour permeability, liquid water absorption, sorption isotherms, thermal conductivity, and air permeability were performed on three Canadian CLT specimens composed of Hem-Fir, Eastern Spruce-Pine-Fir, and Western Spruce-Pine-Fir and one European specimen composed of Spruce. The hygrothermal properties of CLT, considered in this study, appear to be similar to commonly used wood specimens reported in the literature. However, liquid water absorption coefficients of CLT were found to be generally lower than common wood species, possibly due to the presence of glue between the wood layers which limits the moisture movement across the specimen. On the other hand, the air permeability across the CLT specimens varied due to the glue discontinuity within the specimen which led some CLTs to be permeable, however all the European specimens were found to be impermeable. This study also critically analyzed the significance of equilibrium moisture content (EMC) of wood at high relative humidity, measured by means of a pressure plate apparatus and humidity chambers, on the moisture management performance of a wood-frame stucco wall, using the hygrothermal simulation tool hygIRC-2D. The simulation results indicate that the prediction of the moisture response of a wood-frame stucco wall assembly depends significantly on the method adopted to derive the EMC of wood at high RH.

MERS coronaviruses from camels in Africa exhibit region-dependent genetic diversity.

PubMed

Chu, Daniel K W; Hui, Kenrie P Y; Perera, Ranawaka A P M; Miguel, Eve; Niemeyer, Daniela; Zhao, Jincun; Channappanavar, Rudragouda; Dudas, Gytis; Oladipo, Jamiu O; Traoré, Amadou; Fassi-Fihri, Ouafaa; Ali, Abraham; Demissié, Getnet F; Muth, Doreen; Chan, Michael C W; Nicholls, John M; Meyerholz, David K; Kuranga, Sulyman A; Mamo, Gezahegne; Zhou, Ziqi; So, Ray T Y; Hemida, Maged G; Webby, Richard J; Roger, Francois; Rambaut, Andrew; Poon, Leo L M; Perlman, Stanley; Drosten, Christian; Chevalier, Veronique; Peiris, Malik

2018-03-20

Middle East respiratory syndrome coronavirus (MERS-CoV) causes a zoonotic respiratory disease of global public health concern, and dromedary camels are the only proven source of zoonotic infection. Although MERS-CoV infection is ubiquitous in dromedaries across Africa as well as in the Arabian Peninsula, zoonotic disease appears confined to the Arabian Peninsula. MERS-CoVs from Africa have hitherto been poorly studied. We genetically and phenotypically characterized MERS-CoV from dromedaries sampled in Morocco, Burkina Faso, Nigeria, and Ethiopia. Viruses from Africa (clade C) are phylogenetically distinct from contemporary viruses from the Arabian Peninsula (clades A and B) but remain antigenically similar in microneutralization tests. Viruses from West (Nigeria, Burkina Faso) and North (Morocco) Africa form a subclade, C1, that shares clade-defining genetic signatures including deletions in the accessory gene ORF4b Compared with human and camel MERS-CoV from Saudi Arabia, virus isolates from Burkina Faso (BF785) and Nigeria (Nig1657) had lower virus replication competence in Calu-3 cells and in ex vivo cultures of human bronchus and lung. BF785 replicated to lower titer in lungs of human DPP4-transduced mice. A reverse genetics-derived recombinant MERS-CoV (EMC) lacking ORF4b elicited higher type I and III IFN responses than the isogenic EMC virus in Calu-3 cells. However, ORF4b deletions may not be the major determinant of the reduced replication competence of BF785 and Nig1657. Genetic and phenotypic differences in West African viruses may be relevant to zoonotic potential. There is an urgent need for studies of MERS-CoV at the animal-human interface. Copyright © 2018 the Author(s). Published by PNAS.

Spatial variations of storm runoff pollution and their correlation with land-use in a rapidly urbanizing catchment in China.

PubMed

Qin, Hua-Peng; Khu, Soon-Thiam; Yu, Xiang-Ying

2010-09-15

The composition of land use for a rapidly urbanizing catchment is usually heterogeneous, and this may result in significant spatial variations of storm runoff pollution and increase the difficulties of water quality management. The Shiyan Reservoir catchment, a typical rapidly urbanizing area in China, is chosen as a study area, and temporary monitoring sites were set at the downstream of its 6 sub-catchments to synchronously measure rainfall, runoff and water quality during 4 storm events in 2007 and 2009. Due to relatively low frequency monitoring, the IHACRES and exponential pollutant wash-off simulation models are used to interpolate the measured data to compensate for data insufficiency. Three indicators, event pollutant loads per unit area (EPL), event mean concentration (EMC) and pollutant loads transported by the first 50% of runoff volume (FF50), were used to describe the runoff pollution for different pollutants in each sub-catchment during the storm events, and the correlations between runoff pollution spatial variations and land-use patterns were tested by Spearman's rank correlation analysis. The results indicated that similar spatial variation trends were found for different pollutants (EPL or EMC) in light storm events, which strongly correlate with the proportion of residential land use; however, they have different trends in heavy storm events, which correlate with not only the residential land use, but also agricultural and bare land use. And some pairs of pollutants (such as COD/BOD, NH(3)-N/TN) might have the similar source because they have strong or moderate positive spatial correlation. Moreover, the first flush intensity (FF50) varies with impervious land areas and different interception ratio of initial storm runoff volume should be adopted in different sub-catchments. Copyright 2010 Elsevier B.V. All rights reserved.