Science.gov

Sample records for component development part

  1. Development of cryogenic components based on COTS parts for the HARMONI instrument

    NASA Astrophysics Data System (ADS)

    Gigante, José V.; Hernández, Elvio; Rodríguez-Ramos, Luis F.; Estévez, Cristian; Moreno, Antonio F.; Garcia-Lorenzo, Begoña.; Herreros, José M.; Mediavilla, Evencio; Bryson, Ian; Clarke, Fraser; Thatte, Niranjan

    2016-08-01

    HARMONI is an integral field spectrograph working at visible and near-infrared wavelengths. The instrument will be part of the first-light complement at the E-ELT. The IAC is in charge of several work packages and the design of two important components is ongoing: A 'Cryogenic Pupil Mask Rotator' based on a direct drive brushless motor, and a 'Cryogenic Fast Shutter' based on voice coil. One of the main goals of these developments is the use of COTS (Commercial-Off-The-Shelf) parts since their use will reduce costs and short the schedule. Nevertheless, the application of COTS parts in cryo-vacuum is often very difficult and represents a technological challenge.

  2. High temperature ceramics for automobile gas turbines. Part 2: Development of ceramic components

    NASA Technical Reports Server (NTRS)

    Walzer, P.; Koehler, M.; Rottenkolber, P.

    1978-01-01

    The development of ceramic components for automobile gas turbine engines is described with attention given to the steady and unsteady thermal conditions the ceramics will experience, and their anti-corrosion and strain-resistant properties. The ceramics considered for use in the automobile turbines include hot-pressed Si3N4, reaction-sintered, isostatically pressed Si3N4, hot-pressed SiC, reaction-bonded SiC, and glass ceramics. Attention is given to the stress analysis of ceramic structures and the state of the art of ceramic structural technology is reviewed, emphasizing the use of ceramics for combustion chambers and ceramic shrouded turbomachinery (a fully ceramic impeller).

  3. Laser marking of component parts

    SciTech Connect

    Gress, A.V. Jr.

    1983-01-01

    Permanent identification of components and subassemblies for traceability and historical purposes is essential for assemblies subject to long term storage. Marketing requirements run the gamut from simple functional alphanumerics for terminal or wire numbers to complex component identification involving program nomenclature, part number, manufacturer's code, serial number, data code, and lot or batch number. The wide range of opaque materials marked includes both ferrous and nonferrous materials, plastics, composites, and ceramics.

  4. 76 FR 58778 - U.S. Automotive Parts and Components Business Development Mission to Russia

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-22

    ... April 23-28, 2012. Led by a senior Department of Commerce official, this mission is designed to provide... in Russia; and establish research and development activities. In addition to Ford and GM, major...'' in Kaluga. Volkswagen Group has invested more than 500 million Euro in its 150,000 capacity...

  5. GCS component development cycle

    NASA Astrophysics Data System (ADS)

    Rodríguez, Jose A.; Macias, Rosa; Molgo, Jordi; Guerra, Dailos; Pi, Marti

    2012-09-01

    The GTC1 is an optical-infrared 10-meter segmented mirror telescope at the ORM observatory in Canary Islands (Spain). First light was at 13/07/2007 and since them it is in the operation phase. The GTC control system (GCS) is a distributed object & component oriented system based on RT-CORBA8 and it is responsible for the management and operation of the telescope, including its instrumentation. GCS has used the Rational Unified process (RUP9) in its development. RUP is an iterative software development process framework. After analysing (use cases) and designing (UML10) any of GCS subsystems, an initial component description of its interface is obtained and from that information a component specification is written. In order to improve the code productivity, GCS has adopted the code generation to transform this component specification into the skeleton of component classes based on a software framework, called Device Component Framework. Using the GCS development tools, based on javadoc and gcc, in only one step, the component is generated, compiled and deployed to be tested for the first time through our GUI inspector. The main advantages of this approach are the following: It reduces the learning curve of new developers and the development error rate, allows a systematic use of design patterns in the development and software reuse, speeds up the deliverables of the software product and massively increase the timescale, design consistency and design quality, and eliminates the future refactoring process required for the code.

  6. Develop a Model Component

    NASA Technical Reports Server (NTRS)

    Ensey, Tyler S.

    2013-01-01

    During my internship at NASA, I was a model developer for Ground Support Equipment (GSE). The purpose of a model developer is to develop and unit test model component libraries (fluid, electrical, gas, etc.). The models are designed to simulate software for GSE (Ground Special Power, Crew Access Arm, Cryo, Fire and Leak Detection System, Environmental Control System (ECS), etc. .) before they are implemented into hardware. These models support verifying local control and remote software for End-Item Software Under Test (SUT). The model simulates the physical behavior (function, state, limits and 110) of each end-item and it's dependencies as defined in the Subsystem Interface Table, Software Requirements & Design Specification (SRDS), Ground Integrated Schematic (GIS), and System Mechanical Schematic.(SMS). The software of each specific model component is simulated through MATLAB's Simulink program. The intensiv model development life cycle is a.s follows: Identify source documents; identify model scope; update schedule; preliminary design review; develop model requirements; update model.. scope; update schedule; detailed design review; create/modify library component; implement library components reference; implement subsystem components; develop a test script; run the test script; develop users guide; send model out for peer review; the model is sent out for verifictionlvalidation; if there is empirical data, a validation data package is generated; if there is not empirical data, a verification package is generated; the test results are then reviewed; and finally, the user. requests accreditation, and a statement of accreditation is prepared. Once each component model is reviewed and approved, they are intertwined together into one integrated model. This integrated model is then tested itself, through a test script and autotest, so that it can be concluded that all models work conjointly, for a single purpose. The component I was assigned, specifically, was a

  7. Developing a Model Component

    NASA Technical Reports Server (NTRS)

    Fields, Christina M.

    2013-01-01

    The Spaceport Command and Control System (SCCS) Simulation Computer Software Configuration Item (CSCI) is responsible for providing simulations to support test and verification of SCCS hardware and software. The Universal Coolant Transporter System (UCTS) was a Space Shuttle Orbiter support piece of the Ground Servicing Equipment (GSE). The initial purpose of the UCTS was to provide two support services to the Space Shuttle Orbiter immediately after landing at the Shuttle Landing Facility. The UCTS is designed with the capability of servicing future space vehicles; including all Space Station Requirements necessary for the MPLM Modules. The Simulation uses GSE Models to stand in for the actual systems to support testing of SCCS systems during their development. As an intern at Kennedy Space Center (KSC), my assignment was to develop a model component for the UCTS. I was given a fluid component (dryer) to model in Simulink. I completed training for UNIX and Simulink. The dryer is a Catch All replaceable core type filter-dryer. The filter-dryer provides maximum protection for the thermostatic expansion valve and solenoid valve from dirt that may be in the system. The filter-dryer also protects the valves from freezing up. I researched fluid dynamics to understand the function of my component. The filter-dryer was modeled by determining affects it has on the pressure and velocity of the system. I used Bernoulli's Equation to calculate the pressure and velocity differential through the dryer. I created my filter-dryer model in Simulink and wrote the test script to test the component. I completed component testing and captured test data. The finalized model was sent for peer review for any improvements. I participated in Simulation meetings and was involved in the subsystem design process and team collaborations. I gained valuable work experience and insight into a career path as an engineer.

  8. Developing a Model Component

    NASA Technical Reports Server (NTRS)

    Fields, Christina M.

    2013-01-01

    The Spaceport Command and Control System (SCCS) Simulation Computer Software Configuration Item (CSCI) is,. responsible for providing simulations to support test and verification of SCCS hardware and software. The Universal Coolant Transporter System (UCTS) is a Space Shuttle Orbiter support piece of the Ground Servicing Equipment (GSE). The purpose of the UCTS is to provide two support services to the Space Shuttle Orbiter immediately after landing at the Shuttle Landing Facility. The Simulation uses GSE Models to stand in for the actual systems to support testing of SCCS systems s:luring their development. As an intern at KSC, my assignment was to develop a model component for the UCTS. I was given a fluid component (drier) to model in Matlab. The drier was a Catch All replaceable core type filter-drier. The filter-drier provides maximum protection for the thermostatic expansion valve and solenoid valve from dirt that may be in the system. The filter-drier also protects the valves from freezing up. I researched fluid dynamics to understand the function of my component. I completed training for UNIX and Simulink to help aid in my assignment. The filter-drier was modeled by determining affects it has on the pressure, velocity and temperature of the system. I used Bernoulli's Equation to calculate the pressure and velocity differential through the dryer. I created my model filter-drier in Simulink and wrote the test script to test the component. I completed component testing and captured test data. The finalized model was sent for peer review for any improvements.

  9. Component characterization and development 2

    NASA Astrophysics Data System (ADS)

    Smith, Jacqueline D.

    1993-09-01

    The effort entitled, 'Component Characterization and Development II' was established in the Rome Lab Photonics Center Analog & Lightwave Photonics Branch as part of the overall in-house program plan to advanced the state-of-the-art in optics and electrooptics. The objective of the effort is to specify, acquire, and/or develop components for Air Force Command, Control, Communications, and Intelligence (C3I) applications. The source of prototype devices was designated to include academia, industry, and government organizations. Actual performance data was measured for both electro-optic and fiber-optic based devices that were of interest to communications, spatial laser control, and optical beamforming applications. Additionally, several novel approaches to device fabrication were investigated through a BAA contract with Syracuse University.

  10. Definition, analysis and development of an optical data distribution network for integrated avionics and control systems. Part 2: Component development and system integration

    NASA Technical Reports Server (NTRS)

    Yen, H. W.; Morrison, R. J.

    1984-01-01

    Fiber optic transmission is emerging as an attractive concept in data distribution onboard civil aircraft. Development of an Optical Data Distribution Network for Integrated Avionics and Control Systems for commercial aircraft will provide a data distribution network that gives freedom from EMI-RFI and ground loop problems, eliminates crosstalk and short circuits, provides protection and immunity from lightning induced transients and give a large bandwidth data transmission capability. In addition there is a potential for significantly reducing the weight and increasing the reliability over conventional data distribution networks. Wavelength Division Multiplexing (WDM) is a candidate method for data communication between the various avionic subsystems. With WDM all systems could conceptually communicate with each other without time sharing and requiring complicated coding schemes for each computer and subsystem to recognize a message. However, the state of the art of optical technology limits the application of fiber optics in advanced integrated avionics and control systems. Therefore, it is necessary to address the architecture for a fiber optics data distribution system for integrated avionics and control systems as well as develop prototype components and systems.

  11. Nickel-hydrogen component development

    NASA Technical Reports Server (NTRS)

    Charleston, J. A.

    1983-01-01

    Light weight energy storage systems for future space missions are investigated. One of the systems being studied is the nickel hydrogen battery. This battery is designed to achieve longer life, improve performance, and higher energy densities for space applications. The nickel hydrogen component development is discussed. Test data from polarization measurements of the hydrogen electrode component is presented.

  12. Bridging the educational research-teaching practice gap. Curriculum development, Part 1: Components of the curriculum and influences on the process of curriculum design.

    PubMed

    Anderson, Trevor R; Rogan, John M

    2011-01-01

    This article summarizes the major components of curriculum design: vision, operationalization of the vision, design, and evaluation. It stresses that the relationship between these components is dynamic, and that the process of curriculum design does not proceed via a linear application of these components. The article then summarizes some of the major influences on curriculum design: policy, local context, societal expectations, research trends, and technology. Then, it provides examples of how these influences affect the design of a curriculum and ends with a comprehensive set of questions that instructors could use to guide their curriculum development process.

  13. JPL preferred parts list: Reliable electronic components

    NASA Technical Reports Server (NTRS)

    Covey, R. E.; Scott, W. R.; Hess, L. M.; Steffy, T. G.; Stott, F. R.

    1982-01-01

    The JPL Preferred Parts List was prepared to provide a basis for selection of electronic parts for JPL spacecraft programs. Supporting tests for the listed parts were designed to comply with specific spacecraft environmental requirements. The list tabulates the electronic, magnetic, and electromechanical parts applicable to all JPL electronic equipment wherein reliability is a major concern. The parts listed are revelant to equipment supplied by subcontractors as well as fabricated at the laboratory.

  14. 16 CFR 1109.11 - Component part testing for paint.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Component part testing for paint. 1109.11... Component part testing for paint. (a) Generally. The Commission will permit certification of a consumer product, or a component part of a consumer product, as being in compliance with the lead paint limit...

  15. 16 CFR 1109.11 - Component part testing for paint.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Component part testing for paint. 1109.11... Component part testing for paint. (a) Generally. The Commission will permit certification of a consumer product, or a component part of a consumer product, as being in compliance with the lead paint limit...

  16. 16 CFR 1109.11 - Component part testing for paint.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Component part testing for paint. 1109.11... Component part testing for paint. (a) Generally. The Commission will permit certification of a consumer product, or a component part of a consumer product, as being in compliance with the lead paint limit...

  17. MCFC component development at ANL.

    SciTech Connect

    Bloom, I.

    1998-09-15

    Argonne National Laboratory is developing advanced cathode and electrolyte components for the molten carbonate fuel cell (MCFC). Working in support of the MCFC developers, the goal of this effort is to extend the life of the MCFC cell and to improve its performance.

  18. Parts and Components Reliability Assessment: A Cost Effective Approach

    NASA Technical Reports Server (NTRS)

    Lee, Lydia

    2009-01-01

    System reliability assessment is a methodology which incorporates reliability analyses performed at parts and components level such as Reliability Prediction, Failure Modes and Effects Analysis (FMEA) and Fault Tree Analysis (FTA) to assess risks, perform design tradeoffs, and therefore, to ensure effective productivity and/or mission success. The system reliability is used to optimize the product design to accommodate today?s mandated budget, manpower, and schedule constraints. Stand ard based reliability assessment is an effective approach consisting of reliability predictions together with other reliability analyses for electronic, electrical, and electro-mechanical (EEE) complex parts and components of large systems based on failure rate estimates published by the United States (U.S.) military or commercial standards and handbooks. Many of these standards are globally accepted and recognized. The reliability assessment is especially useful during the initial stages when the system design is still in the development and hard failure data is not yet available or manufacturers are not contractually obliged by their customers to publish the reliability estimates/predictions for their parts and components. This paper presents a methodology to assess system reliability using parts and components reliability estimates to ensure effective productivity and/or mission success in an efficient manner, low cost, and tight schedule.

  19. Bridging the Educational Research-Teaching Practice Gap: Curriculum Development, Part 1--Components of the Curriculum and Influences on the Process of Curriculum Design

    ERIC Educational Resources Information Center

    Anderson, Trevor R.; Rogan, John M.

    2011-01-01

    This article summarizes the major components of curriculum design: vision, operationalization of the vision, design, and evaluation. It stresses that the relationship between these components is dynamic, and that the process of curriculum design does not proceed via a linear application of these components. The article then summarizes some of the…

  20. Research and development studies for MHD/coal power flow train components. Part II. Diagnostics and instrumentation MHD channel combutor. Progres report. [Flow calculations for combustors

    SciTech Connect

    Bloom, M.H.; Lederman, S.; Sforza, P.; Matalon, M.

    1980-01-01

    This is Part II of the Technical Progress Report on Tasks II-IV of the subject contract. It deals sequentially with Diagnostics and Instrumentation, the MHD Channel and the Combustor. During this period, a significant effort has gone into establishing a schematic design of a laser diagnostic system which can be applied to the flow-train of the MHD system, and to acquiring, assembling and shaking down a laboratory set-up upon which a prototype can be based. With further reference to the MHD Channel, a model analysis has been initiated of the two-dimensional MHD boundary layer between two electrodes in the limit of small magnetic Reynolds numbers with negligible effect of the flow on the applied magnetic field. An objective of this model study is the assessment of variations in initial conditions on the boundary layer behavior. Finally, the problem of combustion modeling has been studied on an initial basis. The open reports on this subject depict a high degree of empiricism, centering attention on global behavior mainly. A quasi-one-dimensional model code has been set-up to check some of the existing estimates. Also a code for equilibrium combustion has been activated.

  1. Machinability of Green Powder Metallurgy Components: Part II. Sintered Properties of Components Machined in Green State

    NASA Astrophysics Data System (ADS)

    Robert-Perron, Etienne; Blais, Carl; Pelletier, Sylvain; Thomas, Yannig

    2007-06-01

    The green machining process is virtually a must if the powder metallurgy (PM) industries are to solve the lower machining performances associated with PM components. This process is known for lowering the rate of tool wear. Recent improvements in binder/lubricant technologies have led to high-green-strength systems that enable green machining. Combined with the optimized cutting parameters determined in Part I of the study, the green machining of PM components seems to be a viable process for fabricating high performance parts on large scale and complete other shaping processes. This second part of our study presents a comparison between the machining behaviors and the sintered properties of components machined prior to or after sintering. The results show that the radial crush strength measured on rings machined in their green state is equal to that of parts machined after sintering.

  2. 42 CFR 84.62 - Component parts; minimum requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Component parts; minimum requirements. 84.62 Section 84.62 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES...

  3. 42 CFR 84.62 - Component parts; minimum requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 1 2012-10-01 2012-10-01 false Component parts; minimum requirements. 84.62 Section 84.62 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES...

  4. 42 CFR 84.62 - Component parts; minimum requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 1 2013-10-01 2013-10-01 false Component parts; minimum requirements. 84.62 Section 84.62 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES...

  5. 42 CFR 84.62 - Component parts; minimum requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 1 2011-10-01 2011-10-01 false Component parts; minimum requirements. 84.62 Section 84.62 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES...

  6. 42 CFR 84.62 - Component parts; minimum requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 1 2014-10-01 2014-10-01 false Component parts; minimum requirements. 84.62 Section 84.62 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES...

  7. RELAP-7 Pressurizer Component Development Updates

    SciTech Connect

    Zhao, Haihua; Zhang, Hongbin; Zou, Ling; Martineau, Richard; Holten, Michael; Wu, Qiao

    2016-03-01

    RELAP-7 is a nuclear systems safety analysis code being developed at the Idaho National Laboratory (INL). RELAP-7 development began in 2011 to support the Risk Informed Safety Margins Characterization (RISMC) Pathway of the Light Water Reactor Sustainability (LWRS) program. The overall design goal of RELAP-7 is to take advantage of the previous thirty years of advancements in computer architecture, software design, numerical methods, and physical models in order to provide capabilities needed for the RISMC methodology and to support nuclear power safety analysis. The code is being developed based on Idaho National Laboratory’s modern scientific software development framework – MOOSE (the Multi-Physics Object-Oriented Simulation Environment). The initial development goal of the RELAP-7 approach focused primarily on the development of an implicit algorithm capable of strong (nonlinear) coupling of the dependent hydrodynamic variables contained in the 1-D/2-D flow models with the various 0-D system reactor components that compose various boiling water reactor (BWR) and pressurized water reactor nuclear power plants (NPPs). As part of the efforts to expand the capability for PWR simulation, an equilibrium single-region pressurizer model has been implemented in RELAP-7. The pressurizer component can simulate pressure and water level change through insurge, spray, and heating processes. Two simple tests – one for insurge process and another for outsurge process – have been reported to demonstrate and verify the functions of the pressurizer model. The typical single-phase PWR system model presented in the first RELAP-7 milestone report has been updated, as part of system level test for the new pressurizer model. The updated PWR system model with the pressurizer component can be used for more realistic transient simulations. The addition of the equilibrium single-region pressurizer model represents the first step of developing a suite of pressurizer models with

  8. Advanced Electrical Materials and Components Being Developed

    NASA Technical Reports Server (NTRS)

    Schwarze, Gene E.

    2004-01-01

    All aerospace systems require power management and distribution (PMAD) between the energy and power source and the loads. The PMAD subsystem can be broadly described as the conditioning and control of unregulated power from the energy source and its transmission to a power bus for distribution to the intended loads. All power and control circuits for PMAD require electrical components for switching, energy storage, voltage-to-current transformation, filtering, regulation, protection, and isolation. Advanced electrical materials and component development technology is a key technology to increasing the power density, efficiency, reliability, and operating temperature of the PMAD. The primary means to develop advanced electrical components is to develop new and/or significantly improved electronic materials for capacitors, magnetic components, and semiconductor switches and diodes. The next important step is to develop the processing techniques to fabricate electrical and electronic components that exceed the specifications of presently available state-of-the-art components. The NASA Glenn Research Center's advanced electrical materials and component development technology task is focused on the following three areas: 1) New and/or improved dielectric materials for the development of power capacitors with increased capacitance volumetric efficiency, energy density, and operating temperature; 2) New and/or improved high-frequency, high-temperature soft magnetic materials for the development of transformers and inductors with increased power density, energy density, electrical efficiency, and operating temperature; 3) Packaged high-temperature, high-power density, high-voltage, and low-loss SiC diodes and switches.

  9. Bocca : A development environment for HPC components.

    SciTech Connect

    Elwasif, W.; Norris, B.; Allan, B.; Armstrong, R.; Mathematics and Computer Science; ORNL; SNL

    2007-01-01

    In high-performance scientific software development, the emphasis is often on short time to first solution. Even when the development of new components mostly reuses existing components or libraries and only small amounts of new code must be created, dealing with component glue code to obtain complete applications is still tedious and error prone. Component-based software meant to reduce complexity at the application level increases complexity with the attendant glue code. To address these needs, we introduce Bocca, the first tool to enable application developers to perform rapid component prototyping while maintaining robust software engineering practices suitable to HPC environments. Bocca provides project management and a comprehensive build environment for creating and managing applications composed of Common Component Architecture components. Of critical importance for HPC applications, Bocca is designed to operate in a language-agnostic way, simultaneously handling components written in any of the common HPC workstation languages: C, C++, Fortran, Fortran77, Python, and Java. Bocca automates the tasks related to the component glue code, freeing the user to focus on the scientific aspects of the application. Bocca embraces the philosophy pioneered by Ruby Rails for web applications: Start with something that works and evolve it to the user's purpose.

  10. Bocca: A Development Environment for HPC Components

    SciTech Connect

    Elwasif, Wael R; Norris, Boyana; Benjamin, Allan A.; Armstrong, Robert C.

    2007-01-01

    In high-performance scientific software development, the emphasis is often on short time to first solution. Even when the development of new components mostly reuses existing components or libraries and only small amounts of new code must be created, dealing with the component glue code and software build processes to obtain complete applications is still tedious and error-prone. Component-based soft ware meant to reduce complexity at the application level increases complexity with the attendant glue code. To address these needs, we introduce Bocca, the first tool to enable application developers to perform rapid component prototyping while maintaining robust software-engineering practices suitable to HPC environments. Bocca provides project management and a comprehensive build environment for creating and managing applications composed of Common Component Architecture components. Of critical importance for HPC applications, Bocca is designed to operate in a language-agnostic way, simultaneously handling components written in any of the languages commonly used in scientific applications: C, C++, Fortran, Fortran77, Python, and Java. Bocca automates the tasks related to the component glue code, freeing the user to focus on the scientific aspects of the application. Bocca embraces the philosophy pioneered by Ruby Rails for web applications: Start with something that works and evolve it to the user's purpose.

  11. Advanced Electrical Materials and Component Development

    NASA Technical Reports Server (NTRS)

    Schwarze, Gene E.

    2003-01-01

    The primary means to develop advanced electrical components is to develop new and improved materials for magnetic components (transformers, inductors, etc.), capacitors, and semiconductor switches and diodes. This paper will give a description and status of the internal and external research sponsored by NASA Glenn Research Center on soft magnetic materials, dielectric materials and capacitors, and high quality silicon carbide (SiC) atomically smooth substrates. The rationale for and the benefits of developing advanced electrical materials and components for the PMAD subsystem and also for the total power system will be briefly discussed.

  12. 16 CFR 1109.12 - Component part testing for lead content of children's products.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Component part testing for lead content of... Chemicals § 1109.12 Component part testing for lead content of children's products. A certifier may rely on component part testing of each accessible component part of a children's product for lead content,...

  13. 16 CFR 1109.12 - Component part testing for lead content of children's products.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Component part testing for lead content of... Chemicals § 1109.12 Component part testing for lead content of children's products. A certifier may rely on component part testing of each accessible component part of a children's product for lead content,...

  14. 16 CFR 1109.12 - Component part testing for lead content of children's products.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Component part testing for lead content of... Chemicals § 1109.12 Component part testing for lead content of children's products. A certifier may rely on component part testing of each accessible component part of a children's product for lead content,...

  15. Silicon Micromachining for Terahertz Component Development

    NASA Technical Reports Server (NTRS)

    Chattopadhyay, Goutam; Reck, Theodore J.; Jung-Kubiak, Cecile; Siles, Jose V.; Lee, Choonsup; Lin, Robert; Mehdi, Imran

    2013-01-01

    Waveguide component technology at terahertz frequencies has come of age in recent years. Essential components such as ortho-mode transducers (OMT), quadrature hybrids, filters, and others for high performance system development were either impossible to build or too difficult to fabricate with traditional machining techniques. With micromachining of silicon wafers coated with sputtered gold it is now possible to fabricate and test these waveguide components. Using a highly optimized Deep Reactive Ion Etching (DRIE) process, we are now able to fabricate silicon micromachined waveguide structures working beyond 1 THz. In this paper, we describe in detail our approach of design, fabrication, and measurement of silicon micromachined waveguide components and report the results of a 1 THz canonical E-plane filter.

  16. Low-Temperature Electronic Components Being Developed

    NASA Technical Reports Server (NTRS)

    Patterson, Richard L.; Hammond, Ahmad

    1999-01-01

    In many future NASA missions, such as deep space planetary exploration and the Next Generation Space Telescope, electrical components and systems must operate reliably and efficiently in extremely low temperature environments. Most modern electronic components cannot operate below moderately low operating temperatures (-40 to -55 C). The low-temperature electronics program at the NASA Lewis Research Center is focusing on the development and characterization of low-temperature components and the integration of the developed devices into demonstrable very low-temperature (-200 C) power systems such as dc-dc converters. Such low-temperature electronics will not only tolerate hostile environments but also will reduce system size and weight by eliminating radioisotope heating units, thereby reducing launch cost, improving reliability and lifetime, and increasing energy densities. Low-temperature electronic components will also have a great influence on terrestrial applications such as medical instrumentation, magnetic levitation transportation systems, and arctic and antarctic exploration. Lewis researchers are now performing extensive evaluations of commercially available as well as custom-made devices. These include various types of energy storage and signal capacitors, power switching devices, magnetic and superconducting materials, and primary lithium batteries, to name a few.

  17. 42 CFR 84.86 - Component parts exposed to oxygen pressures; minimum requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Component parts exposed to oxygen pressures... PROTECTIVE DEVICES Self-Contained Breathing Apparatus § 84.86 Component parts exposed to oxygen pressures... component parts exposed to oxygen pressures above atmospheric pressure are safe and compatible for...

  18. 42 CFR 84.86 - Component parts exposed to oxygen pressures; minimum requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 1 2013-10-01 2013-10-01 false Component parts exposed to oxygen pressures... PROTECTIVE DEVICES Self-Contained Breathing Apparatus § 84.86 Component parts exposed to oxygen pressures... component parts exposed to oxygen pressures above atmospheric pressure are safe and compatible for...

  19. 42 CFR 84.86 - Component parts exposed to oxygen pressures; minimum requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 1 2012-10-01 2012-10-01 false Component parts exposed to oxygen pressures... PROTECTIVE DEVICES Self-Contained Breathing Apparatus § 84.86 Component parts exposed to oxygen pressures... component parts exposed to oxygen pressures above atmospheric pressure are safe and compatible for...

  20. 42 CFR 84.86 - Component parts exposed to oxygen pressures; minimum requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 1 2011-10-01 2011-10-01 false Component parts exposed to oxygen pressures... PROTECTIVE DEVICES Self-Contained Breathing Apparatus § 84.86 Component parts exposed to oxygen pressures... component parts exposed to oxygen pressures above atmospheric pressure are safe and compatible for...

  1. 42 CFR 84.86 - Component parts exposed to oxygen pressures; minimum requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 1 2014-10-01 2014-10-01 false Component parts exposed to oxygen pressures... PROTECTIVE DEVICES Self-Contained Breathing Apparatus § 84.86 Component parts exposed to oxygen pressures... component parts exposed to oxygen pressures above atmospheric pressure are safe and compatible for...

  2. Sustainable Development in Indian Automotive Component Clusters

    NASA Astrophysics Data System (ADS)

    Bhaskaran, E.

    2013-01-01

    India is the world's second fastest growing auto market and boasts of the sixth largest automobile industry after China, the US, Germany, Japan and Brazil. The Indian auto component industry recorded its highest year-on-year growth of 34.2 % in 2010-2011, raking in revenue of US 39.9 billion; major contribution coming from exports at US five billion and fresh investment from the US at around US two billion. For inclusive growth and sustainable development most of the auto components manufacturers has adopted the cluster development approach. The objective is to study the technical efficiency (θ), peer weights (λ i ), input slacks (S-) and output slacks (S+) of four Auto Component Clusters (ACC) in India. The methodology adopted is using Data Envelopment Analysis of Input Oriented Banker Charnes Cooper Model by taking number of units and number of employments as inputs and sales and exports in crores as an outputs. The non-zero λ i 's represents the weights for efficient clusters. The S > 0 obtained for one ACC reveals the excess no. of units (S-) and employment (S-) and shortage in sales (S+) and exports (S+). However the variable returns to scale are increasing for three clusters, constant for one more cluster and with nil decrease. To conclude, for inclusive growth and sustainable development, the inefficient ACC should increase their turnover and exports, as decrease in no. of enterprises and employment is practically not possible. Moreover for sustainable development, the ACC should strengthen infrastructure interrelationships, technology interrelationships, procurement interrelationships, production interrelationships and marketing interrelationships to increase productivity and efficiency to compete in the world market.

  3. Development of nanostructures on plasma facing components

    NASA Astrophysics Data System (ADS)

    Ruzic, David; Fiflis, Peter; Kalathiparambil, Kishor Kumar

    2015-11-01

    Exposure to low temperature helium plasma, with parameters similar to tokamak edge plasmas, have been found to induce the growth of nanostructures on tungsten. These nanostructures results in an increase in the effective surface area, and will alter the physical properties of the components. Although this has several potential applications in the industrial scenario, it is an undesired effect for fusion reactor components, and is hence necessary to understand their growth mechanisms in order to figure out suitable remedial schemes. Work done using a high density, low temperature helicon discharge plasma source with a resistively heated tungsten wire immersed in the discharge as the substrate have demonstrated the well-defined stages of the growth as a function of total fluence. The required fluence was attained by extending the exposure time. Extensive research work has also shown that a variety of other materials are also prone to develop such structures under similar conditions. In the present work, the effect of the experimental conditions on the various stages of structure development will be presented and a comparison between the structures developed on different types of substrates will be shown.

  4. Hydrogen-bromine fuel cell advance component development

    NASA Technical Reports Server (NTRS)

    Charleston, Joann; Reed, James

    1988-01-01

    Advanced cell component development is performed by NASA Lewis to achieve improved performance and longer life for the hydrogen-bromine fuel cells system. The state-of-the-art hydrogen-bromine system utilizes the solid polymer electrolyte (SPE) technology, similar to the SPE technology developed for the hydrogen-oxygen fuel cell system. These studies are directed at exploring the potential for this system by assessing and evaluating various types of materials for cell parts and electrode materials for Bromine-hydrogen bromine environment and fabricating experimental membrane/electrode-catalysts by chemical deposition.

  5. Motor Development and Learning Difficulties. Part Two.

    ERIC Educational Resources Information Center

    van Eyck, J. W. L.

    1980-01-01

    Part Two of the article focuses on the development of manual motor skills in learning disabled children. After a discussion of test methods, the author considers aspects of a medical examination, including a general exam, a neurological exam, an electroencephalogram, and a diagnostic test of hand/motor skill development. (For Part One, see EC 123…

  6. 40 CFR Appendix I to Part 1068 - Emission-Related Components

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Emission-Related Components I Appendix I to Part 1068 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION..., emission-related components include any engine parts related to the following systems: 1....

  7. 28 CFR Appendix I to Part 16 - Components of the Department of Justice

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 28 Judicial Administration 1 2012-07-01 2012-07-01 false Components of the Department of Justice I Appendix I to Part 16 Judicial Administration DEPARTMENT OF JUSTICE PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION Pt. 16, App. I Appendix I to Part 16—Components of the Department of Justice Unless a...

  8. 32 CFR Appendix F to Part 286 - DoD Freedom of Information Act Program Components

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 2 2011-07-01 2011-07-01 false DoD Freedom of Information Act Program Components F Appendix F to Part 286 National Defense Department of Defense (Continued) OFFICE OF THE... REGULATION Pt. 286, App. F Appendix F to Part 286—DoD Freedom of Information Act Program Components Office...

  9. 32 CFR Appendix F to Part 286 - DoD Freedom of Information Act Program Components

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 2 2010-07-01 2010-07-01 false DoD Freedom of Information Act Program Components F Appendix F to Part 286 National Defense Department of Defense (Continued) OFFICE OF THE... REGULATION Pt. 286, App. F Appendix F to Part 286—DoD Freedom of Information Act Program Components Office...

  10. Advanced Gas Turbine (AGT) Technology Development Project, ceramic component developments

    NASA Technical Reports Server (NTRS)

    Teneyck, M. O.; Macbeth, J. W.; Sweeting, T. B.

    1987-01-01

    The ceramic component technology development activity conducted by Standard Oil Engineered Materials Company while performing as a principal subcontractor to the Garrett Auxiliary Power Division for the Advanced Gas Turbine (AGT) Technology Development Project (NASA Contract DEN3-167) is summarized. The report covers the period October 1979 through July 1987, and includes information concerning ceramic technology work categorized as common and unique. The former pertains to ceramic development applicable to two parallel AGT projects established by NASA contracts DEN3-168 (AGT100) and DEN3-167 (AGT101), whereas the unique work solely pertains to Garrett directed activity under the latter contract. The AGT101 Technology Development Project is sponsored by DOE and administered by NASA-Lewis. Standard Oil directed its efforts toward the development of ceramic materials in the silicon-carbide family. Various shape forming and fabrication methods, and nondestructive evaluation techniques were explored to produce the static structural components for the ceramic engine. This permitted engine testing to proceed without program slippage.

  11. Probabilistic Aeroelastic Analysis Developed for Turbomachinery Components

    NASA Technical Reports Server (NTRS)

    Reddy, T. S. R.; Mital, Subodh K.; Stefko, George L.; Pai, Shantaram S.

    2003-01-01

    Aeroelastic analyses for advanced turbomachines are being developed for use at the NASA Glenn Research Center and industry. However, these analyses at present are used for turbomachinery design with uncertainties accounted for by using safety factors. This approach may lead to overly conservative designs, thereby reducing the potential of designing higher efficiency engines. An integration of the deterministic aeroelastic analysis methods with probabilistic analysis methods offers the potential to design efficient engines with fewer aeroelastic problems and to make a quantum leap toward designing safe reliable engines. In this research, probabilistic analysis is integrated with aeroelastic analysis: (1) to determine the parameters that most affect the aeroelastic characteristics (forced response and stability) of a turbomachine component such as a fan, compressor, or turbine and (2) to give the acceptable standard deviation on the design parameters for an aeroelastically stable system. The approach taken is to combine the aeroelastic analysis of the MISER (MIStuned Engine Response) code with the FPI (fast probability integration) code. The role of MISER is to provide the functional relationships that tie the structural and aerodynamic parameters (the primitive variables) to the forced response amplitudes and stability eigenvalues (the response properties). The role of FPI is to perform probabilistic analyses by utilizing the response properties generated by MISER. The results are a probability density function for the response properties. The probabilistic sensitivities of the response variables to uncertainty in primitive variables are obtained as a byproduct of the FPI technique. The combined analysis of aeroelastic and probabilistic analysis is applied to a 12-bladed cascade vibrating in bending and torsion. Out of the total 11 design parameters, 6 are considered as having probabilistic variation. The six parameters are space-to-chord ratio (SBYC), stagger angle

  12. High temperature thermocouple development program, part A and part B

    NASA Technical Reports Server (NTRS)

    Toenshoff, D. A.; Zysk, E. D.; Fleischner, P. L.

    1972-01-01

    The problem of extending the useful life of thermocouples intended for in-core and out-of-core thermionic applications in a vacuum environment at temperatures up to 2273 K for periods of time up to 10,000 hours was investigated. Many factors that may influence this useful life were examined, and a basic probe design was developed. With a few modifications, twenty-three thermocouple assemblies were fabricated. Generally the finished thermocouple consisted of solid doped W-3% Re and W-25% Re wires and high purity and high density BeO insulators, and was sheathed in a high purity tantalum tube. In a few probes, stranded thermocouple wires were substituted; commercial grade BeO was used; and in two cases, CVD W-22% Re tubing was used. Each of the components was made of the highest purity materials available; was subjected to special cleaning steps, and was assembled in a class 10,000 clean room. Pertinent physical and chemical properties were determined on each of the components. Special processing techniques were used in the fabrication of the high purity (99.95%), high density (over 95% of theoretical) BeO.

  13. Developments in space power components for power management and distribution

    NASA Technical Reports Server (NTRS)

    Renz, D. D.

    1984-01-01

    Advanced power electronic components development for space applications is discussed. The components described include transformers, inductors, semiconductor devices such as transistors and diodes, remote power controllers, and transmission lines.

  14. Development and Characterization of Boehmite Component Simulant

    SciTech Connect

    Russell, Renee L.; Peterson, Reid A.; Smith, Harry D.; Rinehart, Donald E.; Aker, Pamela M.; Buck, Edgar C.

    2009-03-10

    According to Bechtel National Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, “Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes,” simulants for boehmite, gibbsite, and filtration are to be developed that can be used in subsequent bench and integrated testing of the leaching/filtration processes. These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents the results of the boehmite simulant development.

  15. 40 CFR Appendix Vi to Part 86 - Vehicle and Engine Components

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Vehicle and Engine Components VI... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Pt. 86, App. VI Appendix VI to Part 86—Vehicle and Engine Components (a) Light-Duty Vehicles, Light-Duty...

  16. Developing a Research Component of Education

    ERIC Educational Resources Information Center

    Stiles, Lindley J.

    1972-01-01

    The lack of effective research constituency has led to a negative image of educational research. Educators and researchers must get involved in public policy development in order to expand educational research. (MF)

  17. Development and Characterization of Gibbsite Component Simulant

    SciTech Connect

    Russell, Renee L.; Smith, Harry D.; Rinehart, Donald E.; Peterson, Reid A.

    2009-01-29

    According to Bechtel National, Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, "Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes," simulants for boehmite, gibbsite, and filtration are to be developed so they can be used in subsequent bench and integrated testing of the leaching/filtration processes for the River Protection Project-Waste Treatment and Immobilization Plant (RPP-WTP). These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents PNNL’s results of the gibbsite simulant development.

  18. Ceramic component manufacturing process development. Final report

    SciTech Connect

    Robinson, S.

    1996-09-30

    Ceramic materials are well suited for applications where temperature, wear, and corrosion resistance are necessary. The toughness and wear resistance properties that make ceramics desirable, also make fabrication of parts difficult. The objective of this CRADA was to increase the grinding efficiency on Ceradyne Incorporated silicon nitride. This was to be accomplished through optimization of grinding wheel life and increasing silicon nitride material removal rates. Experiments were conducted to determine the relationship between grinding parameters, wheel wear, and material removal rates. Due to excessive, unexplained variation in the experimental results, a consistent relationship between the selected grinding parameters and wheel wear could not be established. Maximum material removal rates were limited by spindle and table drive power. Additional experiments were conducted to evaluate high speed grinding. When compared to conventional grinding speeds, the material removal rates using high speed grinding (13,000 SFM) increased by a factor of five to ten with no degradation of fracture strength.

  19. The Development of Semantic Components of Number.

    ERIC Educational Resources Information Center

    Walker, Alice A.

    In this paper the author reviews and synthesizes the research literature concerning the developmental relationships between conservation of number and linguistic capability in handling of quantitative and relational terms. Several models for the development of these competencies are discussed. On the basis of this review the author concludes that…

  20. Development and Characterization of Boehmite Component Simulant

    SciTech Connect

    Russell, Renee L.; Peterson, Reid A.; Smith, Harry D.; Rinehart, Donald E.; Aker, Pamela M.; Buck, Edgar C.

    2009-06-03

    According to Bechtel National Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, “Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes,” simulants for boehmite, gibbsite, and filtration are to be developed that can be used in subsequent bench and integrated testing of the leaching/filtration processes. These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents the results of the boehmite simulant development and blended simulant crossflow ultrafiltration leaching completed in accordance with the test plan TP-RPP-WTP-469 Rev 0 (WTP Doc. No. 24590- 101-TSA-W000-0004-182-00001 Rev 00A) prepared and approved in response to the cited test specification. This report also includes the results of the aluminate and anion effect on boehmite dissolution performed in accordance with the test plan TP-RPP-WTP-509, Rev 0 (WTP Doc. No. 24590-101-TSA-W000-0004-72-00019 Rev 00A) prepared and approved in response to the Test Specification 24590-WTP-TSP-RT-07-004, Rev 0 (Sundar 2007).

  1. Non-Reactor Micro-Component Development

    SciTech Connect

    Palo, Daniel R.; Stenkamp, Victoria S.; Holladay, Jamie D.; Humble, Paul H.; Dagle, Robert A.; Brooks, Kriston P.

    2007-02-01

    This book chapter will appear in a book being published by Wiley VCH, titled "Micro-Instrumentation for High Throughput Experimentation and Process Intensification." It represents a summary of microchannel-based research in all areas of non-reactive process development, such as heat exchange, mixing, emulsification, phase separation, distillation, mass-transfer, and biological applications.

  2. 76 FR 69545 - Conditions and Requirements for Relying on Component Part Testing or Certification, or Another...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-08

    ...The Consumer Product Safety Commission (``CPSC,'' ``Commission,'' or ``we'') is issuing a final rule regarding the conditions and requirements for relying on testing or certification of either component parts of consumer products, or another party's finished product, or both, to demonstrate, in whole or in part, compliance of a consumer product with all applicable rules, bans, standards, and......

  3. 22 CFR 121.8 - End-items, components, accessories, attachments, parts, firmware, software and systems.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ..., parts, firmware, software and systems. 121.8 Section 121.8 Foreign Relations DEPARTMENT OF STATE...-items, components, accessories, attachments, parts, firmware, software and systems. (a) An end-item is.... Firmware includes but is not limited to circuits into which software has been programmed. (f)...

  4. 22 CFR 121.8 - End-items, components, accessories, attachments, parts, firmware, software and systems.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ..., parts, firmware, software and systems. 121.8 Section 121.8 Foreign Relations DEPARTMENT OF STATE...-items, components, accessories, attachments, parts, firmware, software and systems. (a) An end-item is.... Firmware includes but is not limited to circuits into which software has been programmed. (f)...

  5. Methodology Evaluation Framework for Component-Based System Development.

    ERIC Educational Resources Information Center

    Dahanayake, Ajantha; Sol, Henk; Stojanovic, Zoran

    2003-01-01

    Explains component-based development (CBD) for distributed information systems and presents an evaluation framework, which highlights the extent to which a methodology is component oriented. Compares prominent CBD methods, discusses ways of modeling, and suggests that this is a first step towards a components-oriented systems development…

  6. Peridigm summary report : lessons learned in development with agile components.

    SciTech Connect

    Salinger, Andrew Gerhard; Mitchell, John Anthony; Littlewood, David John; Parks, Michael L.

    2011-09-01

    This report details efforts to deploy Agile Components for rapid development of a peridynamics code, Peridigm. The goal of Agile Components is to enable the efficient development of production-quality software by providing a well-defined, unifying interface to a powerful set of component-based software. Specifically, Agile Components facilitate interoperability among packages within the Trilinos Project, including data management, time integration, uncertainty quantification, and optimization. Development of the Peridigm code served as a testbed for Agile Components and resulted in a number of recommendations for future development. Agile Components successfully enabled rapid integration of Trilinos packages into Peridigm. A cost of this approach, however, was a set of restrictions on Peridigm's architecture which impacted the ability to track history-dependent material data, dynamically modify the model discretization, and interject user-defined routines into the time integration algorithm. These restrictions resulted in modifications to the Agile Components approach, as implemented in Peridigm, and in a set of recommendations for future Agile Components development. Specific recommendations include improved handling of material states, a more flexible flow control model, and improved documentation. A demonstration mini-application, SimpleODE, was developed at the onset of this project and is offered as a potential supplement to Agile Components documentation.

  7. Energy efficient engine component development and integration program

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Accomplishments in the Energy Efficient Engine Component Development and Integration program during the period of April 1, 1981 through September 30, 1981 are discussed. The major topics considered are: (1) propulsion system analysis, design, and integration; (2) engine component analysis, design, and development; (3) core engine tests; and (4) integrated core/low spool testing.

  8. Component-Based Approach in Learning Management System Development

    ERIC Educational Resources Information Center

    Zaitseva, Larisa; Bule, Jekaterina; Makarov, Sergey

    2013-01-01

    The paper describes component-based approach (CBA) for learning management system development. Learning object as components of e-learning courses and their metadata is considered. The architecture of learning management system based on CBA being developed in Riga Technical University, namely its architecture, elements and possibilities are…

  9. 19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and... United States Coast Guard, aircraft, aircraft engines, and ground flight simulators, including...

  10. 19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and... United States Coast Guard, aircraft, aircraft engines, and ground flight simulators, including...

  11. 19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and... United States Coast Guard, aircraft, aircraft engines, and ground flight simulators, including...

  12. 19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and... United States Coast Guard, aircraft, aircraft engines, and ground flight simulators, including...

  13. 19 CFR 10.183 - Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components...

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Duty-free entry of civil aircraft, aircraft engines, ground flight simulators, parts, components, and... aircraft, aircraft engines, and ground flight simulators, including their parts, components, and... United States Coast Guard, aircraft, aircraft engines, and ground flight simulators, including...

  14. Probabilistic Structural Analysis Methods (PSAM) for select space propulsion system components, part 2

    NASA Technical Reports Server (NTRS)

    1991-01-01

    The technical effort and computer code enhancements performed during the sixth year of the Probabilistic Structural Analysis Methods program are summarized. Various capabilities are described to probabilistically combine structural response and structural resistance to compute component reliability. A library of structural resistance models is implemented in the Numerical Evaluations of Stochastic Structures Under Stress (NESSUS) code that included fatigue, fracture, creep, multi-factor interaction, and other important effects. In addition, a user interface was developed for user-defined resistance models. An accurate and efficient reliability method was developed and was successfully implemented in the NESSUS code to compute component reliability based on user-selected response and resistance models. A risk module was developed to compute component risk with respect to cost, performance, or user-defined criteria. The new component risk assessment capabilities were validated and demonstrated using several examples. Various supporting methodologies were also developed in support of component risk assessment.

  15. The Development and Validation of the Empathy Components Questionnaire (ECQ)

    PubMed Central

    Batchelder, Laurie; Brosnan, Mark; Ashwin, Chris

    2017-01-01

    Key research suggests that empathy is a multidimensional construct comprising of both cognitive and affective components. More recent theories and research suggest even further factors within these components of empathy, including the ability to empathize with others versus the drive towards empathizing with others. While numerous self-report measures have been developed to examine empathy, none of them currently index all of these wider components together. The aim of the present research was to develop and validate the Empathy Components Questionnaire (ECQ) to measure cognitive and affective components, as well as ability and drive components within each. Study one utilized items measuring cognitive and affective empathy taken from various established questionnaires to create an initial version of the ECQ. Principal component analysis (PCA) was used to examine the underlying components of empathy within the ECQ in a sample of 101 typical adults. Results revealed a five-component model consisting of cognitive ability, cognitive drive, affective ability, affective drive, and a fifth factor assessing affective reactivity. This five-component structure was then validated and confirmed using confirmatory factor analysis (CFA) in an independent sample of 211 typical adults. Results also showed that females scored higher than males overall on the ECQ, and on specific components, which is consistent with previous findings of a female advantage on self-reported empathy. Findings also showed certain components predicted scores on an independent measure of social behavior, which provided good convergent validity of the ECQ. Together, these findings validate the newly developed ECQ as a multidimensional measure of empathy more in-line with current theories of empathy. The ECQ provides a useful new tool for quick and easy measurement of empathy and its components for research with both healthy and clinical populations. PMID:28076406

  16. Development of swinging part profilometer for optics

    NASA Astrophysics Data System (ADS)

    Zhang, Peng; Li, Jie; Yu, Guoyu; Walker, David D.

    2016-11-01

    A new surface metrology instrument, the `Swinging Part Profilometer' (SPP), has been developed for in-situ measurement of optics undergoing robot-processing in the ground (non-specular) state. In this paper, we present the hardware-design of the SPP, together with software for hardware-control, data-acquisition and surface-reconstruction. First results on a sample part are presented, compared with interferometric metrology, and error-contributions considered. Notably, during each individual scan of a measurement-cycle, the probe remains fixed. This lends itself to automated probe-deployment by the same robot as performs surface-processing, as probe stability is required on only the time-scale for a single scan.

  17. 10 CFR 72.156 - Identification and control of materials, parts, and components.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Identification and control of materials, parts, and components. 72.156 Section 72.156 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSING REQUIREMENTS FOR THE INDEPENDENT STORAGE OF SPENT NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND...

  18. 40 CFR Appendix I to Part 1068 - Emission-Related Components

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Emission-Related Components I Appendix I to Part 1068 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION...*. 8. Control Solenoids*. 9. Electronic Controls*. 10. Vacuum Control Diaphragms*. 11. Control...

  19. 40 CFR Appendix I to Part 1068 - Emission-Related Components

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Emission-Related Components I Appendix I to Part 1068 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION...*. 9. Electronic Controls*. 10. Vacuum Control Diaphragms*. 11. Control Cables*. 12. Control...

  20. 49 CFR Appendix A to Part 215 - Railroad Freight Car Components

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Railroad Freight Car Components A Appendix A to Part 215 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Pt. 215, App. A Appendix A...

  1. 49 CFR Appendix A to Part 215 - Railroad Freight Car Components

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Railroad Freight Car Components A Appendix A to Part 215 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Pt. 215, App. A Appendix A...

  2. 22 CFR 121.8 - End-items, components, accessories, attachments, parts, firmware, software and systems.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 22 Foreign Relations 1 2012-04-01 2012-04-01 false End-items, components, accessories, attachments, parts, firmware, software and systems. 121.8 Section 121.8 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS THE UNITED STATES MUNITIONS LIST Enumeration of Articles § 121.8...

  3. 22 CFR 121.8 - End-items, components, accessories, attachments, parts, firmware, software, and systems.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 22 Foreign Relations 1 2014-04-01 2014-04-01 false End-items, components, accessories, attachments, parts, firmware, software, and systems. 121.8 Section 121.8 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS THE UNITED STATES MUNITIONS LIST Enumeration of Articles § 121.8...

  4. 22 CFR 121.8 - End-items, components, accessories, attachments, parts, firmware, software and systems.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 22 Foreign Relations 1 2013-04-01 2013-04-01 false End-items, components, accessories, attachments, parts, firmware, software and systems. 121.8 Section 121.8 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS THE UNITED STATES MUNITIONS LIST Enumeration of Articles § 121.8...

  5. 40 CFR Appendix I to Part 1068 - Emission-Related Components

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Emission-Related Components I Appendix I to Part 1068 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR HIGHWAY, STATIONARY, AND NONROAD PROGRAMS Pt. 1068, App....

  6. 40 CFR Appendix I to Part 1068 - Emission-Related Components

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Emission-Related Components I Appendix I to Part 1068 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR HIGHWAY, STATIONARY, AND NONROAD PROGRAMS Pt. 1068, App....

  7. Disasters and development: Part I. Relationships between disasters and development.

    PubMed

    Stephenson, Rob S; DuFrane, Charles

    2002-01-01

    This module introduces a paradigm for understanding the disaster/development interface. Specifically, the module asserts that disasters and development are linked closely in that disasters can both destroy development initiatives and create development opportunities, and that development schemes can both increase and decrease vulnerability. The module consists of four parts: Part One introduces these concepts and discusses how disasters can vary from one type of hazard to another, as well as from one type of economic condition to another. Part Two develops the paradigm in depth, and provides case examples to amplify the points made in the text. Part Three describes and discusses different methods and tools for analyzing decisions for potential investment of resources, and should enhance the reader's capacity to analyze the mitigational benefits of development alternatives in both the pre- and post-disaster context. Part Four conceptualizes the role of UN agencies, NGOs, and the affected communities in promoting development based on the concepts discussed in the module. This training module, Disasters and Development, initially was designed to introduce this aspect of disaster management to an audience of UN organization professionals who form disaster management teams, as well as to government counterpart agencies, non-governmental organizations (NGOs), and donors. The educational process has been designed to increase the audience's awareness of the nature and management of disasters, in order to lead to better performance in disaster preparedness and response. The content has been written by experts in the field of disaster management and in general follows the UNDP/UNDRO Disaster Management Manual and its principles, procedures, and terminology.

  8. Recent developments in plastic optical fiber components for automotive applications

    NASA Astrophysics Data System (ADS)

    Cirillo, James R.; Jennings, Kurt L.; Lynn, Mark A.; Steele, Robert E.

    1993-02-01

    The majority of production applications using plastic optical fiber (POF) have been for illumination applications. These applications continue to be refined and new illumination applications continue to be introduced. Point-to-point data communication applications of POF are beginning to appear in production vehicles. New developments in connection systems and networking components are occurring rapidly. This paper discusses recently developed components for illumination and data communications. The illumination components were designed for three different applications: lamp monitoring, keyhole illumination, and PRNDL indication (gear shift). Components for data communications include two connection systems and two passive stars designed for networking. The two connections systems are a 16 electrical/1 optical system for point-to-point links and a 5 electrical/2 optical for two-way optical communications. The two stars are a 16 node star and 7 node star. Performance characteristics and design advantages are described for all components.

  9. Adult Basic Education Component; Manpower Development Component; and Program Evaluation. Delta Opportunities Corporation: Final Report.

    ERIC Educational Resources Information Center

    Delta Opportunities Corp., Greenville, MS.

    The Adult Education Component of the Delta Opportunities Corporation (DOC) operated learning centers in four Mississippi delta counties for educationally disadvantaged rural poor adults. The centers served an excess of 200 participants, preparing them for General Education Development Tests (GED) and providing prevocational and adult basic…

  10. Machinability of Green Powder Metallurgy Components: Part I. Characterization of the Influence of Tool Wear

    NASA Astrophysics Data System (ADS)

    Robert-Perron, Etienne; Blais, Carl; Pelletier, Sylvain; Thomas, Yannig

    2007-06-01

    The green machining process is an interesting approach for solving the mediocre machining behavior of high-performance powder metallurgy (PM) steels. This process appears as a promising method for extending tool life and reducing machining costs. Recent improvements in binder/lubricant technologies have led to high green strength systems that enable green machining. So far, tool wear has been considered negligible when characterizing the machinability of green PM specimens. This inaccurate assumption may lead to the selection of suboptimum cutting conditions. The first part of this study involves the optimization of the machining parameters to minimize the effects of tool wear on the machinability in turning of green PM components. The second part of our work compares the sintered mechanical properties of components machined in green state with other machined after sintering.

  11. Energy efficient engine. Volume 1: Component development and integration program

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Technology for achieving lower installed fuel consumption and lower operating costs in future commercial turbofan engines are developed, evaluated, and demonstrated. The four program objectives are: (1) propulsion system analysis; (2) component analysis, design, and development; (3) core design, fabrication, and test; and (4) integrated core/low spoon design, fabrication, and test.

  12. Advanced Electrical Materials and Components Development: An Update

    NASA Technical Reports Server (NTRS)

    Schwarze, Gene E.

    2005-01-01

    The primary means to develop advanced electrical components is to develop new and improved materials for magnetic components (transformers, inductors, etc.), capacitors, and semiconductor switches and diodes. This paper will give an update of the Advanced Power Electronics and Components Technology being developed by the NASA Glenn Research Center for use in future Power Management and Distribution subsystems used in space power systems for spacecraft and lunar and planetary surface power. The initial description and status of this technology program was presented two years ago at the First International Energy Conversion Engineering Conference held at Portsmouth, Virginia, August 2003. The present paper will give a brief background of the previous work reported and a summary of research performed the past several years on soft magnetic materials characterization, dielectric materials and capacitor developments, high quality silicon carbide atomically smooth substrates, and SiC static and dynamic device characterization under elevated temperature conditions. The rationale for and the benefits of developing advanced electrical materials and components for the PMAD subsystem and also for the total power system will also be briefly discussed.

  13. Ceramic Composite Development for Gas Turbine Engine Hot Section Components

    NASA Technical Reports Server (NTRS)

    DiCarlo, James A.; VANrOODE, mARK

    2006-01-01

    The development of ceramic materials for incorporation into the hot section of gas turbine engines has been ongoing for about fifty years. Researchers have designed, developed, and tested ceramic gas turbine components in rigs and engines for automotive, aero-propulsion, industrial, and utility power applications. Today, primarily because of materials limitations and/or economic factors, major challenges still remain for the implementation of ceramic components in gas turbines. For example, because of low fracture toughness, monolithic ceramics continue to suffer from the risk of failure due to unknown extrinsic damage events during engine service. On the other hand, ceramic matrix composites (CMC) with their ability to display much higher damage tolerance appear to be the materials of choice for current and future engine components. The objective of this paper is to briefly review the design and property status of CMC materials for implementation within the combustor and turbine sections for gas turbine engine applications. It is shown that although CMC systems have advanced significantly in thermo-structural performance within recent years, certain challenges still exist in terms of producibility, design, and affordability for commercial CMC turbine components. Nevertheless, there exist some recent successful efforts for prototype CMC components within different engine types.

  14. Microalgae as part of the autotrophic component of life support systems for future planetary bases

    NASA Astrophysics Data System (ADS)

    Sychev, Vladimir; Levinskikh, Margarita

    Research and development of human life support systems incorporating biospheric components performed in the USSR and Russia for over 50 years resulted in a well- structured and rational step-by-step approach to this area of activities. The development of biological life support systems (BLSS) was based on the theory of biocenology advanced by V.N. Sukachev, according to which organic matter turnover is a result of combined activities of plants, animals and microorganisms. Hence, a BLSS with its semi-closed matter turnover needs to incorporate all the components of natural ecosystems, i.e., plants (photoautotrophic organisms), animals, including humans, and microorganisms (heterotrophic organisms). The photoautotrophic component of the BLSS designed to support humans should meet a number of specific requirements, the most important of which are: - high productivity - stability of functional parameters within their normal fluctuation ranges - compatibility with other system components to preclude additional load on them - minimum of un-utilizable compounds in the material balance of the component. The photosynthetic component may consist of lower and higher plants, which may function separately or jointly. In either case, microalgae will play a key role, as they do on Earth, in the production of organic compounds and oxygen as well as in the support of BLSS reliability. The construction of a planetary base begins with the assembly of major engineering facilities whereas the construction of a BLSS starts after the assembly is complete and the base interior is fully separated from the outside environment. At early stages of base operation the autotrophic component of the system will consist of algae alone, which will provide photosynthetic regeneration of air and water. At later stages the autotrophic component will progress from lower to higher plants; when the greenhouses reach adequate sizes, higher plants will occupy the major portion of the autotrophic component

  15. Magnetohydrodynamic projects at the CDIF (Component Development and Integration Facility)

    SciTech Connect

    Not Available

    1990-01-01

    This quarterly technical progress report presents the tasks accomplished at the Component Development and Integration Facility during the fourth quarter of FY90. Areas of technical progress this quarter included: coal system development; seed system development; test bay modification; channel power dissipation and distribution system development; oxygen system storage upgrade; iron core magnet thermal protection system oxygen checkout; TRW slag rejector/CDIF slag removal project; stack gas/environmental compliance upgrade; coal-fired combustor support; 1A channels fabrication and assembly; support of Mississippi State University diagnostic testing; test operations and results; data enhancement; data analysis and modeling; technical papers; and projected activities. 2 tabs.

  16. Physical activity versus cardiorespiratory fitness: two (partly) distinct components of cardiovascular health?

    PubMed

    DeFina, Laura F; Haskell, William L; Willis, Benjamin L; Barlow, Carolyn E; Finley, Carrie E; Levine, Benjamin D; Cooper, Kenneth H

    2015-01-01

    Physical activity (PA) and cardiorespiratory fitness (CRF) both have inverse relationships to cardiovascular (CV) morbidity and mortality. Recent position papers and guidelines have identified the important role of both of these factors in CV health. The benefits of PA and CRF in the prevention of CV disease and risk factors are reviewed. In addition, assessment methodology and utilization in the research and clinical arenas are discussed. Finally, the benefits, methodology, and utilization are compared and contrasted to better understand the two (partly) distinct components and their impact on CV health.

  17. 10 CFR Appendix D to Part 110 - Illustrative List of Aerodynamic Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Equipment and Components Under NRC Export Licensing Authority D Appendix D to Part 110 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) EXPORT AND IMPORT OF NUCLEAR EQUIPMENT AND MATERIAL Pt. 110, App. D Appendix D to Part 110—Illustrative List of Aerodynamic Enrichment Plant Equipment and Components Under...

  18. 10 CFR Appendix D to Part 110 - Illustrative List of Aerodynamic Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Equipment and Components Under NRC Export Licensing Authority D Appendix D to Part 110 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) EXPORT AND IMPORT OF NUCLEAR EQUIPMENT AND MATERIAL Pt. 110, App. D Appendix D to Part 110—Illustrative List of Aerodynamic Enrichment Plant Equipment and Components Under...

  19. 10 CFR Appendix D to Part 110 - Illustrative List of Aerodynamic Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Equipment and Components Under NRC Export Licensing Authority D Appendix D to Part 110 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) EXPORT AND IMPORT OF NUCLEAR EQUIPMENT AND MATERIAL Pt. 110, App. D Appendix D to Part 110—Illustrative List of Aerodynamic Enrichment Plant Equipment and Components Under...

  20. A systems tester for compact HPG component development

    NASA Astrophysics Data System (ADS)

    Walls, W. A.; Vaughn, M. R.

    1984-03-01

    To facilitate the development of more compact homopolar generators (HPGs), the compact HPG systems tester was designed and built to develop the system and component technology necessary to design HPGs having energy densities of up to 60 MJ/cu m. The systems tester is one-half of a full-scale counter-rotating HPG storing 2.5 MJ at 6,900 rpm and generating 20 V. Incorporated in the tester are two new types of components, face brushes and a stationary-shaft hydrostatic bearing, which will lead to HPG designs that will rotate a larger fraction of the magnetic circuit while eliminating much of the stationary support structure. The systems tester is designed to provide a facility for future bearing research and development of the higher-current-density brushgear required for drawing larger currents from the smaller slip ring areas of more compact machines.

  1. Reusable Component Model Development Approach for Parallel and Distributed Simulation

    PubMed Central

    Zhu, Feng; Yao, Yiping; Chen, Huilong; Yao, Feng

    2014-01-01

    Model reuse is a key issue to be resolved in parallel and distributed simulation at present. However, component models built by different domain experts usually have diversiform interfaces, couple tightly, and bind with simulation platforms closely. As a result, they are difficult to be reused across different simulation platforms and applications. To address the problem, this paper first proposed a reusable component model framework. Based on this framework, then our reusable model development approach is elaborated, which contains two phases: (1) domain experts create simulation computational modules observing three principles to achieve their independence; (2) model developer encapsulates these simulation computational modules with six standard service interfaces to improve their reusability. The case study of a radar model indicates that the model developed using our approach has good reusability and it is easy to be used in different simulation platforms and applications. PMID:24729751

  2. Structural analysis methods development for turbine hot section components

    NASA Technical Reports Server (NTRS)

    Thompson, R. L.

    1989-01-01

    The structural analysis technologies and activities of the NASA Lewis Research Center's gas turbine engine HOT Section Technoloogy (HOST) program are summarized. The technologies synergistically developed and validated include: time-varying thermal/mechanical load models; component-specific automated geometric modeling and solution strategy capabilities; advanced inelastic analysis methods; inelastic constitutive models; high-temperature experimental techniques and experiments; and nonlinear structural analysis codes. Features of the program that incorporate the new technologies and their application to hot section component analysis and design are described. Improved and, in some cases, first-time 3-D nonlinear structural analyses of hot section components of isotropic and anisotropic nickel-base superalloys are presented.

  3. An overview: Component development for solar thermal systems

    NASA Astrophysics Data System (ADS)

    Mancini, T. R.

    In this paper, I review the significant issues and the development of solar concentrators and thermal receivers for central-receiver power plants and dish/engine systems. Due to the breadth of the topic area, I have arbitrarily narrowed the content of this paper by choosing not to discuss line-focus (trough) systems and energy storage. I will focus my discussion on the development of heliostats, dishes, and receivers since the 1970s with an emphasis on describing the technologies and their evolution, identifying some key observations and lessons learned, and suggesting what the future in component development may be.

  4. Development of Nonelectronic Part Cyclic Failure Rates

    DTIC Science & Technology

    1977-12-01

    for a short duration. The dc operation allows the current to build up to rated value during energization with no overshoot. Protective devices, such...failures/ houL 4.3 Part Classes and Failure Rates To update Sections 2.9, 2.10, and 2.11 of MIL-HDBK-217B, failure rate mathematical models and base

  5. Development of sensors for ceramic components in advanced propulsion systems

    NASA Technical Reports Server (NTRS)

    Atkinson, William H.; Cyr, M. A.; Strange, R. R.

    1994-01-01

    The 'Development of Sensors for Ceramics Components in Advanced Propulsion Systems' program was divided into two phases. The objectives of Phase 1 were to analyze, evaluate and recommend sensor concepts for the measurement of surface temperature, strain and heat flux on ceramic components for advanced propulsion systems. The results of this effort were previously published in NASA CR-182111. As a result of Phase 1, three approaches were recommended for further development: pyrometry, thin-film sensors, and thermographic phosphors. The objectives of Phase 2 were to fabricate and conduct laboratory demonstration tests of these systems. A summary report of the Phase 2 effort, together with conclusions and recommendations for each of the categories evaluated, has been submitted to NASA. Emittance tests were performed on six materials furnished by NASA Lewis Research Center. Measurements were made of various surfaces at high temperature using a Thermogage emissometer. This report describes the emittance test program and presents a summary of the results.

  6. Scorpion venom components as potential candidates for drug development.

    PubMed

    Ortiz, Ernesto; Gurrola, Georgina B; Schwartz, Elisabeth Ferroni; Possani, Lourival D

    2015-01-01

    Scorpions are well known for their dangerous stings that can result in severe consequences for human beings, including death. Neurotoxins present in their venoms are responsible for their toxicity. Due to their medical relevance, toxins have been the driving force in the scorpion natural compounds research field. On the other hand, for thousands of years, scorpions and their venoms have been applied in traditional medicine, mainly in Asia and Africa. With the remarkable growth in the number of characterized scorpion venom components, several drug candidates have been found with the potential to tackle many of the emerging global medical threats. Scorpions have become a valuable source of biologically active molecules, from novel antibiotics to potential anticancer therapeutics. Other venom components have drawn attention as useful scaffolds for the development of drugs. This review summarizes the most promising candidates for drug development that have been isolated from scorpion venoms.

  7. Computer Developments and the Administrator, Part I.

    ERIC Educational Resources Information Center

    Landford, R. R.

    1979-01-01

    Computer developments that might concern educational administrators are outlined, including physical size, processing performance, peripheral performance, cost of computation, and software development. Computer development and advances in data processing technology are expected to continue to be as dramatic in the 1980s as they have in the past 25…

  8. Robust principal component analysis in water quality index development

    NASA Astrophysics Data System (ADS)

    Ali, Zalina Mohd; Ibrahim, Noor Akma; Mengersen, Kerrie; Shitan, Mahendran; Juahir, Hafizan

    2014-06-01

    Some statistical procedures already available in literature are employed in developing the water quality index, WQI. The nature of complexity and interdependency that occur in physical and chemical processes of water could be easier explained if statistical approaches were applied to water quality indexing. The most popular statistical method used in developing WQI is the principal component analysis (PCA). In literature, the WQI development based on the classical PCA mostly used water quality data that have been transformed and normalized. Outliers may be considered in or eliminated from the analysis. However, the classical mean and sample covariance matrix used in classical PCA methodology is not reliable if the outliers exist in the data. Since the presence of outliers may affect the computation of the principal component, robust principal component analysis, RPCA should be used. Focusing in Langat River, the RPCA-WQI was introduced for the first time in this study to re-calculate the DOE-WQI. Results show that the RPCA-WQI is capable to capture similar distribution in the existing DOE-WQI.

  9. Advanced diesel engine component development program, tasks 4-14

    NASA Astrophysics Data System (ADS)

    Kaushal, Tony S.; Weber, Karen E.

    1994-11-01

    This report summarizes the Advanced Diesel Engine Component Development (ADECD) Program to develop and demonstrate critical technology needed to advance the heavy-duty low heat rejection engine concept. Major development activities reported are the design, analysis, and fabrication of monolithic ceramic components; vapor phase and solid film lubrication; electrohydraulic valve actuation; and high pressure common rail injection. An advanced single cylinder test bed was fabricated as a laboratory tool in studying these advanced technologies. This test bed simulates the reciprocator for a system having no cooling system, turbo compounding, Rankine bottoming cycle, common rail injection, and variable valve actuation to achieve fuel consumption of 160 g/kW-hr (.26 lb/hp-hr). The advanced concepts were successfully integrated into the test engine. All ceramic components met their functional and reliability requirements. The firedeck, cast-in-place ports, valves, valve guides, piston cap, and piston ring were made from silicon nitride. Breakthroughs required to implement a 'ceramic' engine included the fabrication of air-gap cylinder heads, elimination of compression gaskets, machining of ceramic valve seats within the ceramic firedeck, fabrication of cast-in-place ceramic port liners, implementation of vapor phase lubrication, and elimination of the engine coolant system. Silicon nitride valves were successfully developed to meet several production abuse test requirements and incorporated into the test bed with a ceramic valve guide and solid film lubrication. The ADECD cylinder head features ceramic port shields to increase insulation and exhaust energy recovery. The combustion chamber includes a ceramic firedeck and piston cap. The tribological challenge posed by top ring reversal temperatures of 550 C was met through the development of vapor phase lubrication using tricresyl phosphate at the ring-liner interface. A solenoid-controlled, variable valve actuation system

  10. Advanced diesel engine component development program, tasks 4-14

    NASA Technical Reports Server (NTRS)

    Kaushal, Tony S.; Weber, Karen E.

    1994-01-01

    This report summarizes the Advanced Diesel Engine Component Development (ADECD) Program to develop and demonstrate critical technology needed to advance the heavy-duty low heat rejection engine concept. Major development activities reported are the design, analysis, and fabrication of monolithic ceramic components; vapor phase and solid film lubrication; electrohydraulic valve actuation; and high pressure common rail injection. An advanced single cylinder test bed was fabricated as a laboratory tool in studying these advanced technologies. This test bed simulates the reciprocator for a system having no cooling system, turbo compounding, Rankine bottoming cycle, common rail injection, and variable valve actuation to achieve fuel consumption of 160 g/kW-hr (.26 lb/hp-hr). The advanced concepts were successfully integrated into the test engine. All ceramic components met their functional and reliability requirements. The firedeck, cast-in-place ports, valves, valve guides, piston cap, and piston ring were made from silicon nitride. Breakthroughs required to implement a 'ceramic' engine included the fabrication of air-gap cylinder heads, elimination of compression gaskets, machining of ceramic valve seats within the ceramic firedeck, fabrication of cast-in-place ceramic port liners, implementation of vapor phase lubrication, and elimination of the engine coolant system. Silicon nitride valves were successfully developed to meet several production abuse test requirements and incorporated into the test bed with a ceramic valve guide and solid film lubrication. The ADECD cylinder head features ceramic port shields to increase insulation and exhaust energy recovery. The combustion chamber includes a ceramic firedeck and piston cap. The tribological challenge posed by top ring reversal temperatures of 550 C was met through the development of vapor phase lubrication using tricresyl phosphate at the ring-liner interface. A solenoid-controlled, variable valve actuation system

  11. Valuing Professional Development Components for Emerging Undergraduate Researchers

    NASA Astrophysics Data System (ADS)

    Cheung, I.

    2015-12-01

    In 2004 the Hatfield Marine Science Center (HMSC) at Oregon State University (OSU) established a Research Experience for Undergraduates (REU) program to engage undergraduate students in hands-on research training in the marine sciences. The program offers students the opportunity to conduct research focused on biological and ecological topics, chemical and physical oceanography, marine geology, and atmospheric science. In partnership with state and federal government agencies, this ten-week summer program has grown to include 20+ students annually. Participants obtain a background in the academic discipline, professional development training, and research experience to make informed decisions about careers and advanced degrees in marine and earth system sciences. Professional development components of the program are designed to support students in their research experience, explore career goals and develop skills necessary to becoming a successful young marine scientist. These components generally include seminars, discussions, workshops, lab tours, and standards of conduct. These componentscontribute to achieving the following professional development objectives for the overall success of new emerging undergraduate researchers: Forming a fellowship of undergraduate students pursuing marine research Stimulating student interest and understanding of marine research science Learning about research opportunities at Oregon State University "Cross-Training" - broadening the hands-on research experience Exploring and learning about marine science careers and pathways Developing science communication and presentation skills Cultivating a sense of belonging in the sciences Exposure to federal and state agencies in marine and estuarine science Academic and career planning Retention of talented students in the marine science Standards of conduct in science Details of this program's components, objectives and best practices will be discussed.

  12. Research, Development and Innovation: Contextual Analysis. Part Two.

    ERIC Educational Resources Information Center

    Radnor, Michael; And Others

    Part 2 of a three-part volume for research and development systems researchers, this report attempts to apply the contextual analysis framework of research, development, and innovation (RD & I) activities presented in Part 1. The authors make a detailed analysis of RD & I activities in the sectors of education, civilian aviation, health,…

  13. Expression of COPI components during development of Drosophila melanogaster.

    PubMed

    Grieder, Nicole C; Kloter, Urs; Gehring, Walter J

    2005-12-01

    In a P{lArB} enhancer detector collection, a line was found that showed upregulated expression within centrally to posteriorly located germarial cysts. It was inserted in the gammaCOP locus on chromosome 3R. GammaCOP is a component of the COPI coatomer involved in membrane traffic. Most of the other known components of the COPI coatomer also showed higher expression in the posterior half of the germarium. Not only meiotic germline cysts but also migrating follicle cells upregulate the COPI subunits. During embryonic and larval development, the COPI subunits are expressed ubiquitously as expected for genes required for cell viability. In addition, they are strongly expressed in the salivary glands and the proventriculus. Whether tissue-specific transcriptional upregulation of COPI subunits is required for the reorganization of membranous compartments that are needed for the developmental processes that confer cyst polarity and follicle maturation will have to be addressed in a genetic study.

  14. Recent Developments in Radioastronomy--Part 2.

    ERIC Educational Resources Information Center

    Booth, R. S.

    1980-01-01

    Described are recent developments and discoveries in radioastronomy. Topics discussed include galactic structures, stellar evolution, the binary pulsar and general relativity, extragalactic radioastronomy, model of the source of radioactive emission and quasars. (DS)

  15. Preceptor Development: Providing Effective Feedback, Part 2

    PubMed Central

    Wilkinson, Samaneh T.; Phillips, Holly

    2014-01-01

    Abstract An integral part of providing effective feedback to pharmacy residents occurs during the evaluation process. Residency evaluation involves measuring and documenting performance as it relates to standardized residency outcomes, goals, and learning objectives. Evaluations may be formative or summative and include the preceptor’s evaluation of the resident’s performance, the resident’s self-assessments, and the resident’s evaluation of the preceptor and learning experience. Evaluations are more structured than feedback, and they involve documentation of the verbal feedback that was provided throughout the learning experience. This article will focus on the preceptor’s role in providing effective resident evaluations based on specific learning activities. PMID:24958969

  16. 12 CFR Appendix 1 to Part 24 - CD-1-National Bank Community Development (Part 24) Investments

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 1 2011-01-01 2011-01-01 false CD-1-National Bank Community Development (Part 24) Investments 1 Appendix 1 To Part 24 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY COMMUNITY AND ECONOMIC DEVELOPMENT ENTITIES, COMMUNITY DEVELOPMENT PROJECTS, AND...

  17. 12 CFR Appendix 1 to Part 24 - CD-1-National Bank Community Development (Part 24) Investments

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false CD-1-National Bank Community Development (Part 24) Investments 1 Appendix 1 To Part 24 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY COMMUNITY AND ECONOMIC DEVELOPMENT ENTITIES, COMMUNITY DEVELOPMENT PROJECTS, AND...

  18. 12 CFR Appendix 1 to Part 24 - CD-1-National Bank Community Development (Part 24) Investments

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 1 2012-01-01 2012-01-01 false CD-1-National Bank Community Development (Part 24) Investments 1 Appendix 1 To Part 24 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY COMMUNITY AND ECONOMIC DEVELOPMENT ENTITIES, COMMUNITY DEVELOPMENT PROJECTS, AND...

  19. 12 CFR Appendix 1 to Part 24 - CD-1-National Bank Community Development (Part 24) Investments

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 1 2013-01-01 2013-01-01 false CD-1-National Bank Community Development (Part 24) Investments 1 Appendix 1 To Part 24 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY COMMUNITY AND ECONOMIC DEVELOPMENT ENTITIES, COMMUNITY DEVELOPMENT PROJECTS, AND...

  20. EDUCATION AND THE DEVELOPMENT OF IN-RESIDENCE TRAINING PROGRAMS, PART I, PART II.

    ERIC Educational Resources Information Center

    MELICAN, ROBERT L.; PURCELL, FRANCIS P.

    THE TWO PARTS OF THIS DISCUSSION CONSIDER THE DEVELOPMENT OF RESIDENTIAL PROGRAMS FOR VOCATIONAL AND SOCIAL TRAINING TO MEET THE PROBLEMS OF THE LOW-INCOME SCHOOL DROPOUT. PART I REVIEWS THE HISTORICAL BACKGROUND OF RESIDENCY PROGRAMS IN SUCH EDUCATIONAL INSTITUTIONS AS COLLEGES, UNIVERSITIES, CHURCHES, AND SUMMER CAMPS. PART II DEALS WITH THE…

  1. Evaluating innovation. Part 2: Development in neurosurgery.

    PubMed

    Schnurman, Zane; Kondziolka, Douglas

    2016-01-01

    OBJECT Patients, practitioners, payers, and regulators are advocating for reform in how medical advances are evaluated. Because surgery does not adhere to a standardized developmental pathway, how the medical community accepts a procedure remains unclear. The authors developed a new model, using publication data and patterns, that quantifies this process. Using this technique, the authors identified common archetypes and influences on neurosurgical progress from idea inception to acceptance. METHODS Seven neurosurgical procedures developed in the past 15-25 years were used as developmental case studies (endovascular coil, deep brain stimulation, vagus nerve stimulation, 1,3-bis(2-chloroethyl)-l-nitrosourea wafer, and 3 radiosurgery procedures), and the literature on each topic was evaluated. A new metric the authors termed "progressive scholarly acceptance" (PSA) was used as an end point for community acceptance. PSA was reached when the number of investigations that refine or improve a procedure eclipsed the total number of reports assessing initial efficacy. Report characteristics, including the number of patients studied, study design, and number of authoring groups from the first report to the point of PSA, were assessed. RESULTS Publication data implicated factors that had an outsized influence on acceptance. First, procedural accessibility to investigators was found to influence the number of reports, number of patients studied, and number of authoring groups contributing. Barriers to accessibility included target disease rarity, regulatory restrictions, and cost. Second, the ease or difficulty in applying a randomized controlled trial had an impact on study design. Based on these 2 factors, 3 developmental archetypes were characterized to generally describe the development of surgery. CONCLUSIONS Common surgical development archetypes can be described based on factors that impact investigative methods, data accumulation, and ultimate acceptance by society

  2. ANL's research and development of alternative components for MCFC's

    SciTech Connect

    Kucera, G.H.; Brown, A.P.; Roche, M.; Chu, D.; Indacochea, E.

    1992-01-01

    Molten carbonate fuel cell (MCFC) systems are currently limited by several technical problems. The objectives of this project are to focus on these problems and develop materials . and cell components that will ameliorate or eliminate them. Specifically, new ceramic materials are being investigated for dimensionally stable electrode materials with improved chemical and electrochemical properties over the present NiO cathode and Ni/Cr and Ni/Al anodes. Also, altemative electrolyte formulations to the present Li{sub 2}CO{sub 3}-K{sub 2}CO{sub 3} are being studied.

  3. Principal Component-Based Radiative Transfer Model (PCRTM) for Hyperspectral Sensors. Part I; Theoretical Concept

    NASA Technical Reports Server (NTRS)

    Liu, Xu; Smith, William L.; Zhou, Daniel K.; Larar, Allen

    2005-01-01

    Modern infrared satellite sensors such as Atmospheric Infrared Sounder (AIRS), Cosmic Ray Isotope Spectrometer (CrIS), Thermal Emission Spectrometer (TES), Geosynchronous Imaging Fourier Transform Spectrometer (GIFTS) and Infrared Atmospheric Sounding Interferometer (IASI) are capable of providing high spatial and spectral resolution infrared spectra. To fully exploit the vast amount of spectral information from these instruments, super fast radiative transfer models are needed. This paper presents a novel radiative transfer model based on principal component analysis. Instead of predicting channel radiance or transmittance spectra directly, the Principal Component-based Radiative Transfer Model (PCRTM) predicts the Principal Component (PC) scores of these quantities. This prediction ability leads to significant savings in computational time. The parameterization of the PCRTM model is derived from properties of PC scores and instrument line shape functions. The PCRTM is very accurate and flexible. Due to its high speed and compressed spectral information format, it has great potential for super fast one-dimensional physical retrievals and for Numerical Weather Prediction (NWP) large volume radiance data assimilation applications. The model has been successfully developed for the National Polar-orbiting Operational Environmental Satellite System Airborne Sounder Testbed - Interferometer (NAST-I) and AIRS instruments. The PCRTM model performs monochromatic radiative transfer calculations and is able to include multiple scattering calculations to account for clouds and aerosols.

  4. Research, Development and Innovation: Contextual Analysis. Part One.

    ERIC Educational Resources Information Center

    Radnor, Michael; And Others

    Part 1 of a three-part volume for research and development (R & D) systems researchers, this report attempts to provide a basic understanding of the process of contextual analysis for research, development, and innovation. The term "research development and innovation" (RD & I) is used to describe the total process of innovation…

  5. Development of a 5-Component Balance for Water Tunnel Applications

    NASA Technical Reports Server (NTRS)

    Suarez, Carlos J.; Kramer, Brian R.; Smith, Brooke C.

    1999-01-01

    The principal objective of this research/development effort was to develop a multi-component strain gage balance to measure both static and dynamic forces and moments on models tested in flow visualization water tunnels. A balance was designed that allows measuring normal and side forces, and pitching, yawing and rolling moments (no axial force). The balance mounts internally in the model and is used in a manner typical of wind tunnel balances. The key differences between a water tunnel balance and a wind tunnel balance are the requirement for very high sensitivity since the loads are very low (typical normal force is 90 grams or 0.2 lbs), the need for water proofing the gage elements, and the small size required to fit into typical water tunnel models. The five-component balance was calibrated and demonstrated linearity in the responses of the primary components to applied loads, very low interactions between the sections and no hysteresis. Static experiments were conducted in the Eidetics water tunnel with delta wings and F/A-18 models. The data were compared to forces and moments from wind tunnel tests of the same or similar configurations. The comparison showed very good agreement, providing confidence that loads can be measured accurately in the water tunnel with a relatively simple multi-component internal balance. The success of the static experiments encouraged the use of the balance for dynamic experiments. Among the advantages of conducting dynamic tests in a water tunnel are less demanding motion and data acquisition rates than in a wind tunnel test (because of the low-speed flow) and the capability of performing flow visualization and force/moment (F/M) measurements simultaneously with relative simplicity. This capability of simultaneous flow visualization and for F/M measurements proved extremely useful to explain the results obtained during these dynamic tests. In general, the development of this balance should encourage the use of water tunnels for a

  6. Development of wear resistant ceramic coatings for diesel engine components

    SciTech Connect

    Haselkorn, M.H. )

    1992-04-01

    Improved fuel economy and a reduction of emissions can be achieved by insulation of the combustion chamber components to reduce heat rejection. However, insulating the combustion chamber components will also increase the operating temperature of the piston ring/cylinder liner interface from approximately 150{degree}C to over 300{degree}C. Existing ring/liner materials can not withstand these higher operating temperatures and for this reason, new materials need to be developed for this critical tribological interface. The overall goal of this program is the development of piston ring/cylinder liner material pairs which would be able to provide the required friction and wear properties at these more severe operating conditions. More specifically, this program first selected, and then evaluated, potential d/wear resistant coatings which could be applied to either piston rings an or cylinder liners and provide, at 350{degree}C under lubricated conditions, coefficients of friction below 0.1 and wear rates of less than 25 {times} lO{sup {minus}6} mm/hour. The processes selected for applying the candidate wear resistant coatings to piston rings and/or cylinder liners were plasma spraying, chemical vapor, physical vapor and low temperature arc vapor deposition techniques as well as enameling techniques.

  7. Development of Prototype HTS Components for Magnetic Suspension Applications

    NASA Technical Reports Server (NTRS)

    Haldar, P.; Hoehn, J., Jr.; Selvamanickam, V.; Farrell, R. A.; Balachandran, U.; Iyer, A. N.; Peterson, E.; Salazar, K.

    1996-01-01

    We have concentrated on developing prototype lengths of bismuth and thallium based silver sheathed superconductors by the powder-in-tube approach to fabricate high temperature superconducting (HTS) components for magnetic suspension applications. Long lengths of mono and multi filament tapes are presently being fabricated with critical current densities useful for maglev and many other applications. We have recently demonstrated the prototype manufacture of lengths exceeding 1 km of Bi-2223 multi filament conductor. Long lengths of thallium based multi-filament conductor have also been fabricated with practical levels of critical current density and improved field dependence behavior. Test coils and magnets have been built from these lengths and characterized over a range of temperatures and background fields to determine their performance. Work is in progress to develop, fabricate and test HTS windings that will be suitable for magnetic suspension, levitation and other electric power related applications.

  8. Review on surface mounting components (wire wound chip resistors) development

    NASA Astrophysics Data System (ADS)

    Shiota, Shigeo; Nakao, Masahiro; Shimizu, Akira

    1992-08-01

    An overview of the development review on surface mounting components (wire wound chip resistors) is presented. Temperature rise tests were conducted on wire wound chip resistors installing them on substrates made of alumina, glass epoxy resin, or polyimide to determine their temperature rise characteristics, and maximum load factors were determined taking substrate heat resisting temperature and solder melting temperature into consideration. Evaluation tests were conducted on the filters' resistance to environments (thermal shock, anti hydroscopicity, thermal stability, loaded life, shock, random vibration, radiation resistance, out gassing), and the subject filters functioned satisfactory with exception of difficulty of conducting the thermal stability test at 125 C which was lower than the temperature specified in the NASDA's (National Space Development Agency of Japan's) specification due to problems of heat resistance of the molding resin material.

  9. Development of impact design methods for ceramic gas turbine components

    NASA Technical Reports Server (NTRS)

    Song, J.; Cuccio, J.; Kington, H.

    1990-01-01

    Impact damage prediction methods are being developed to aid in the design of ceramic gas turbine engine components with improved impact resistance. Two impact damage modes were characterized: local, near the impact site, and structural, usually fast fracture away from the impact site. Local damage to Si3N4 impacted by Si3N4 spherical projectiles consists of ring and/or radial cracks around the impact point. In a mechanistic model being developed, impact damage is characterized as microcrack nucleation and propagation. The extent of damage is measured as volume fraction of microcracks. Model capability is demonstrated by simulating late impact tests. Structural failure is caused by tensile stress during impact exceeding material strength. The EPIC3 code was successfully used to predict blade structural failures in different size particle impacts on radial and axial blades.

  10. Inertial confinement fusion target component fabrication and technology development report

    NASA Astrophysics Data System (ADS)

    Steinman, D.

    1994-03-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities which took place under this contract during the period of October 1, 1992 through September 30, 1993. During this period, GA was assigned 18 tasks in support of the Inertial Confinement Fusion program and its laboratories. These tasks included 'Capabilities Activation' and 'Capabilities Demonstration' to enable us to begin production of glass and composite polymer capsules. Capsule delivery tasks included 'Small Glass Shell Deliveries' and 'Composite Polymer Capsules' for Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL). We also were asked to provide direct 'Onsite Support' at LLNL and LANL. We continued planning for the transfer of 'Micromachining Equipment from Rocky Flats' and established 'Target Component Micromachining and Electroplating Facilities' at GA. We fabricated over 1100 films and filters of 11 types for Sandia National Laboratory and provided full-time onsite engineering support for target fabrication and characterization. We initiated development of methods to make targets for the Naval Research Laboratory. We investigated spherical interferometry, built an automated capsule sorter, and developed an apparatus for calorimetric measurement of fuel fill for LLNL. We assisted LANL in the 'Characterization of Opaque b-Layered Targets.' We developed deuterated and UV-opaque polymers for use by the University of Rochester's Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process.

  11. Development Of Software To Recognize Parts Of Plants

    NASA Technical Reports Server (NTRS)

    Despain, Ronald R.; Tharpe, Roy, Jr.; Davis, Leon; Hauss, Sharon; Shawaga, Larry; Biro, Ron

    1993-01-01

    Report describes first phase in development of digital image-processing subsystem recognizing parts of plants. Subsystem part of robotic system tending and harvesting plants in automated plant-growth chamber. Initial focus on image-processing software that distinguishes among seed heads, stems, and leaves of wheat plants and further distinguishes between these parts and background. Software adaptable to other types of plants.

  12. Blood borne: bacterial components in mother's blood influence fetal development.

    PubMed

    Loughran, Allister J; Tuomanen, Elaine I

    2016-01-01

    Bacterial or viral infection of the mother during the course of pregnancy can cross the placenta and actively infect the fetus. However, especially for bacteria, it is more common for mothers to experience an infection that can be treated without overt fetal infection. In this setting, it is less well understood what the risk to fetal development is, particularly in terms of neurological development. This research highlight reviews recent findings indicating that bacterial components generated during infection of the mother can cross the placenta and activate the fetal innate immune system resulting in changes in the course of brain development and subsequent progression to postnatal cognitive disorders. Bacterial cell wall is a ubiquitous bacterial PAMP (pathogen-associated molecular pattern) known to activate inflammation through the stimulation of TLR2. Cell wall is released from bacteria during antibiotic treatment and new work shows that embryos exposed to cell wall from the mother demonstrate anomalous proliferation of neuronal precursor cells in a TLR2 dependent manner. Such proliferation increases the neuronal density of the cortical plate and alters brain architecture. Although there is no fetal death, subsequent cognitive development is significantly impaired. This model system suggests that bacterial infection of the mother and its treatment can impact fetal brain development and requires greater understanding to potentially eliminate a risk factor for cognitive disorders such as autism.

  13. Static Feed Water Electrolysis Subsystem Testing and Component Development

    NASA Technical Reports Server (NTRS)

    Koszenski, E. P.; Schubert, F. H.; Burke, K. A.

    1983-01-01

    A program was carried out to develop and test advanced electrochemical cells/modules and critical electromechanical components for a static feed (alkaline electrolyte) water electrolysis oxygen generation subsystem. The accomplishments were refurbishment of a previously developed subsystem and successful demonstration for a total of 2980 hours of normal operation; achievement of sustained one-person level oxygen generation performance with state-of-the-art cell voltages averaging 1.61 V at 191 ASF for an operating temperature of 128F (equivalent to 1.51V when normalized to 180F); endurance testing and demonstration of reliable performance of the three-fluid pressure controller for 8650 hours; design and development of a fluid control assembly for this subsystem and demonstration of its performance; development and demonstration at the single cell and module levels of a unitized core composite cell that provides expanded differential pressure tolerance capability; fabrication and evaluation of a feed water electrolyte elimination five-cell module; and successful demonstration of an electrolysis module pressurization technique that can be used in place of nitrogen gas during the standby mode of operation to maintain system pressure and differential pressures.

  14. Mast cells are an essential hematopoietic component for polyp development

    PubMed Central

    Gounaris, Elias; Erdman, Susan E.; Restaino, Clifford; Gurish, Michael F.; Friend, Daniel S.; Gounari, Fotini; Lee, David M.; Zhang, Guoying; Glickman, Jonathan N.; Shin, Kichul; Rao, Varada P.; Poutahidis, Theofilos; Weissleder, Ralph; McNagny, Kelly M.; Khazaie, Khashayarsha

    2007-01-01

    It is generally agreed that most colon cancers develop from adenomatous polyps, and it is this fact on which screening strategies are based. Although there is overwhelming evidence to link intrinsic genetic lesions with the formation of these preneoplastic lesions, recent data suggest that the tumor stromal environment also plays an essential role in this disease. In particular, it has been suggested that CD34+ immature myeloid precursor cells are required for tumor development and invasion. Here we have used mice conditional for the stabilization of β-catenin or defective for the adenomatous polyposis coli (APC) gene to reinvestigated the identity and importance of tumor-infiltrating hematopoietic cells in polyposis. We show that, from the onset, polyps are infiltrated with proinflammatory mast cells (MC) and their precursors. Depletion of MC either pharmacologically or through the generation of chimeric mice with genetic lesions in MC development leads to a profound remission of existing polyps. Our data suggest that MC are an essential hematopoietic component for preneoplastic polyp development and are a novel target for therapeutic intervention. PMID:18077429

  15. A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing Part I: System Analysis, Component Identification, Additive Manufacturing, and Testing of Polymer Composites

    NASA Technical Reports Server (NTRS)

    Grady, Joseph E.; Haller, William J.; Poinsatte, Philip E.; Halbig, Michael C.; Schnulo, Sydney L.; Singh, Mrityunjay; Weir, Don; Wali, Natalie; Vinup, Michael; Jones, Michael G.; Patterson, Clark; Santelle, Tom; Mehl, Jeremy

    2015-01-01

    The research and development activities reported in this publication were carried out under NASA Aeronautics Research Institute (NARI) funded project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing." The objective of the project was to conduct evaluation of emerging materials and manufacturing technologies that will enable fully nonmetallic gas turbine engines. The results of the activities are described in three part report. The first part of the report contains the data and analysis of engine system trade studies, which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. The technical scope of activities included an assessment of the feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composites, which were accomplished by fabricating prototype engine components and testing them in simulated engine operating conditions. The manufacturing process parameters were developed and optimized for polymer and ceramic composites (described in detail in the second and third part of the report). A number of prototype components (inlet guide vane (IGV), acoustic liners, engine access door) were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included turbine nozzle components. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail.

  16. Liquid Oxygen/Liquid Methane Component Technology Development at MSFC

    NASA Technical Reports Server (NTRS)

    Robinson, Joel W.

    2010-01-01

    The National Aeronautics & Space Administration (NASA) has identified Liquid Oxygen (LOX)/Liquid Methane (LCH4) as a potential propellant combination for future space vehicles based upon exploration studies. The technology is estimated to have higher performance and lower overall systems mass compared to existing hypergolic propulsion systems. Besides existing in-house risk reduction activities, NASA has solicited from industry their participation on component technologies based on the potential application to the lunar ascent main engine (AME). Contracted and NASA efforts have ranged from valve technologies to engine system testbeds. The application for the AME is anticipated to be an expendable, pressure-fed engine for ascent from the moon at completion of its lunar stay. Additionally, the hardware is expected to provide an abort capability prior to landing, in the event that descent systems malfunction. For the past 4 years, MSFC has been working with the Glenn Research Center and the Johnson Space Center on methane technology development. This paper will focus on efforts specific to MSFC in pursuing ignition, injector performance, chamber material assessments and cryogenic valve technologies. Ignition studies have examined characteristics for torch, spark and microwave systems. Injector testing has yielded insight into combustion performance for shear, swirl and impinging type injectors. The majority of chamber testing has been conducted with ablative and radiatively cooled chambers with planned activities for regenerative and transpiration cooled chambers. Lastly, an effort is underway to examine the long duration exposure issues of cryogenic valve internal components. The paper will summarize the status of these efforts.

  17. Expression of Wnt Signaling Components during Xenopus Pronephros Development

    PubMed Central

    Zhang, Bo; Tran, Uyen; Wessely, Oliver

    2011-01-01

    Background The formation of the vertebrate kidney is tightly regulated and relies on multiple evolutionarily conserved inductive events. These are present in the complex metanephric kidney of higher vertebrates, but also in the more primitive pronephric kidney functional in the larval stages of amphibians and fish. Wnts have long been viewed as central in this process. Canonical β-Catenin-dependent Wnt signaling establishes kidney progenitors and non-canonical β-Catenin-independent Wnt signaling participate in the morphogenetic processes that form the highly sophisticated nephron structure. While some individual Wnt signaling components have been studied extensively in the kidney, the overall pathway has not yet been analyzed in depth. Methodology/Principal Findings Here we report a detailed expression analysis of all Wnt ligands, receptors and several downstream Wnt effectors during pronephros development in Xenopus laevis using in situ hybridization. Out of 19 Wnt ligands, only three, Wnt4, Wnt9a and Wnt11, are specifically expressed in the pronephros. Others such as Wnt8a are present, but in a broader domain comprising adjacent tissues in addition to the kidney. The same paradigm is observed for the Wnt receptors and its downstream signaling components. Fzd1, Fzd4, Fzd6, Fzd7, Fzd8 as well as Celsr1 and Prickle1 show distinct expression domains in the pronephric kidney, whereas the non-traditional Wnt receptors, Ror2 and Ryk, as well as the majority of the effector molecules are rather ubiquitous. In addition to this spatial regulation, the timing of expression is also tightly regulated. In particular, non-canonical Wnt signaling seems to be restricted to later stages of pronephros development. Conclusion/Significance Together these data suggest a complex cross talk between canonical and non-canonical Wnt signaling is required to establish a functional pronephric kidney. PMID:22028899

  18. Cognitive components underpinning the development of model-based learning.

    PubMed

    Potter, Tracey C S; Bryce, Nessa V; Hartley, Catherine A

    2016-10-29

    Reinforcement learning theory distinguishes "model-free" learning, which fosters reflexive repetition of previously rewarded actions, from "model-based" learning, which recruits a mental model of the environment to flexibly select goal-directed actions. Whereas model-free learning is evident across development, recruitment of model-based learning appears to increase with age. However, the cognitive processes underlying the development of model-based learning remain poorly characterized. Here, we examined whether age-related differences in cognitive processes underlying the construction and flexible recruitment of mental models predict developmental increases in model-based choice. In a cohort of participants aged 9-25, we examined whether the abilities to infer sequential regularities in the environment ("statistical learning"), maintain information in an active state ("working memory") and integrate distant concepts to solve problems ("fluid reasoning") predicted age-related improvements in model-based choice. We found that age-related improvements in statistical learning performance did not mediate the relationship between age and model-based choice. Ceiling performance on our working memory assay prevented examination of its contribution to model-based learning. However, age-related improvements in fluid reasoning statistically mediated the developmental increase in the recruitment of a model-based strategy. These findings suggest that gradual development of fluid reasoning may be a critical component process underlying the emergence of model-based learning.

  19. Development and fabrication of structural components for a scramjet engine

    NASA Technical Reports Server (NTRS)

    Buchmann, O. A.

    1990-01-01

    A program broadly directed toward design and development of long-life (100 hours and 1,000 cycles with a goal of 1,000 hours and 10,000 cycles) hydrogen-cooled structures for application to scramjets is presented. Previous phases of the program resulted in an overall engine design and analytical and experimental characterization of selected candidate materials and concepts. The latter efforts indicated that the basic life goals for the program can be reached with available means. The main objective of this effort was an integrated, experimental evaluation of the results of the previous program phases. The fuel injection strut was selected for this purpose, including fabrication development and fabrication of a full-scale strut. Testing of the completed strut was to be performed in a NASA-Langley wind tunnel. In addition, conceptual designs were formulated for a heat transfer test unit and a flat panel structural test unit. Tooling and fabrication procedures required to fabricate the strut were developed, and fabrication and delivery to NASA of all strut components, including major subassemblies, were completed.

  20. Engineering development of selective agglomeration: Task 6, Operation of the Component Development Test Facility

    SciTech Connect

    Not Available

    1991-09-01

    The objective of this report is to summarize the component development and laboratory binder test work at Wilsonville during Task 6. This Task included the construction and startup of the Component Development Test Facility (CDTF), coal procurement, evaluation of unit operation and dewatering performance, laboratory binder tests for diesel and heptane, production characterization, and vendor tests. Data evaluation, interpretation, and analysis are not included in this report, but will be discussed in the Task 7 report.

  1. Perspectives on Spiritual Development as Part of Youth Development

    ERIC Educational Resources Information Center

    Quinn, Jane

    2008-01-01

    Speaking to the issue of spiritual development from her extensive experience as a youth work practitioner, the author notes several ideas she finds particularly compelling, among them that spiritual development interacts with, yet is distinct from, moral and religious development; that spiritual development is a core construct of identity…

  2. Inertial Confinement Fusion Target Component Fabrication and Technology Development Support

    SciTech Connect

    Steinman, D.

    1993-03-01

    On December 31, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities of the period January 1, 1991 through September 30, 1992. During this period, GA was assigned 15 tasks in support of the Inertial Confinement Fusion program and its laboratories. These tasks included Facilities Activation, Staff Development, and Capabilities Validation to establish facilities and equipment, and demonstrate capability to perform ICF target fabrication research, development and production activities. The capabilities developed and demonstrated are those needed for fabrication and precise characterization of polymer shells and polymer coatings. We made progress toward production capability for glass shells, barrier layer coatings, and gas idling of shells. We fabricated over 1000 beam diagnostic foil targets for Sandia National Laboratory Albuquerque and provided full-time on-site engineering support for target fabrication and characterization. We initiated development of methods to fabricate polymer shells by a controlled mass microencapsulation technique, and performed chemical syntheses of several chlorine- and silicon-doped polymer materials for the University of Rochester's Laboratory for Laser Energetics (UR/LLE). We performed the conceptual design of a cryogenic target handling system for UR/LLE that will fill, transport, layer, and characterize targets filled with cryogenic deuterium or deuterium-tritium fuel, and insert these cryogenic targets into the OMEGA-Upgrade target chamber for laser implosion experiments. This report summarizes and documents the technical progress made on these tasks.

  3. Inertial confinement fusion target component fabrication and technology development support

    NASA Astrophysics Data System (ADS)

    Steinman, D.

    1993-03-01

    On December 31, 1990, the U.S. Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities of the period January 1, 1991 through September 30, 1992. During this period, GA was assigned 15 tasks in support of the Inertial Confinement Fusion program and its laboratories. These tasks included Facilities Activation, Staff Development, and Capabilities Validation to establish facilities and equipment, and demonstrate capability to perform ICF target fabrication research, development, and production activities. The capabilities developed and demonstrated are those needed for fabrication and precise characterization of polymer shells and polymer coatings. We made progress toward production capability for glass shells, barrier layer coatings, and gas idling of shells. We fabricated over 1000 beam diagnostic foil targets for Sandia National Laboratory Albuquerque and provided full-time on-site engineering support for target fabrication and characterization. We initiated development of methods to fabricate polymer shells by a controlled mass microencapsulation technique, and performed chemical syntheses of several chlorine- and silicon-doped polymer materials for the University of Rochester's Laboratory for Laser Energetics (UR/LLE). We performed the conceptual design of a cryogenic target handling system for UR/LLE that will fill, transport, layer, and characterize targets filled with cryogenic deuterium or deuterium-tritium fuel, and insert these cryogenic targets into the OMEGA-Upgrade target chamber for laser implosion experiments. This report summarizes and documents the technical progress made on these tasks.

  4. Potential of direct metal deposition technology for manufacturing thick functionally graded coatings and parts for reactors components

    NASA Astrophysics Data System (ADS)

    Thivillon, L.; Bertrand, Ph.; Laget, B.; Smurov, I.

    2009-03-01

    Direct metal deposition (DMD) is an automated 3D deposition process arising from laser cladding technology with co-axial powder injection to refine or refurbish parts. Recently DMD has been extended to manufacture large-size near-net-shape components. When applied for manufacturing new parts (or their refinement), DMD can provide tailored thermal properties, high corrosion resistance, tailored tribology, multifunctional performance and cost savings due to smart material combinations. In repair (refurbishment) operations, DMD can be applied for parts with a wide variety of geometries and sizes. In contrast to the current tool repair techniques such as tungsten inert gas (TIG), metal inert gas (MIG) and plasma welding, laser cladding technology by DMD offers a well-controlled heat-treated zone due to the high energy density of the laser beam. In addition, this technology may be used for preventative maintenance and design changes/up-grading. One of the advantages of DMD is the possibility to build functionally graded coatings (from 1 mm thickness and higher) and 3D multi-material objects (for example, 100 mm-sized monolithic rectangular) in a single-step manufacturing cycle by using up to 4-channel powder feeder. Approved materials are: Fe (including stainless steel), Ni and Co alloys, (Cu,Ni 10%), WC compounds, TiC compounds. The developed coatings/parts are characterized by low porosity (<1%), fine microstructure, and their microhardness is close to the benchmark value of wrought alloys after thermal treatment (Co-based alloy Stellite, Inox 316L, stainless steel 17-4PH). The intended applications concern cooling elements with complex geometry, friction joints under high temperature and load, light-weight mechanical support structures, hermetic joints, tubes with complex geometry, and tailored inside and outside surface properties, etc.

  5. A Dormant Microbial Component in the Development of Preeclampsia

    PubMed Central

    Kell, Douglas B.; Kenny, Louise C.

    2016-01-01

    Preeclampsia (PE) is a complex, multisystem disorder that remains a leading cause of morbidity and mortality in pregnancy. Four main classes of dysregulation accompany PE and are widely considered to contribute to its severity. These are abnormal trophoblast invasion of the placenta, anti-angiogenic responses, oxidative stress, and inflammation. What is lacking, however, is an explanation of how these themselves are caused. We here develop the unifying idea, and the considerable evidence for it, that the originating cause of PE (and of the four classes of dysregulation) is, in fact, microbial infection, that most such microbes are dormant and hence resist detection by conventional (replication-dependent) microbiology, and that by occasional resuscitation and growth it is they that are responsible for all the observable sequelae, including the continuing, chronic inflammation. In particular, bacterial products such as lipopolysaccharide (LPS), also known as endotoxin, are well known as highly inflammagenic and stimulate an innate (and possibly trained) immune response that exacerbates the inflammation further. The known need of microbes for free iron can explain the iron dysregulation that accompanies PE. We describe the main routes of infection (gut, oral, and urinary tract infection) and the regularly observed presence of microbes in placental and other tissues in PE. Every known proteomic biomarker of “preeclampsia” that we assessed has, in fact, also been shown to be raised in response to infection. An infectious component to PE fulfills the Bradford Hill criteria for ascribing a disease to an environmental cause and suggests a number of treatments, some of which have, in fact, been shown to be successful. PE was classically referred to as endotoxemia or toxemia of pregnancy, and it is ironic that it seems that LPS and other microbial endotoxins really are involved. Overall, the recognition of an infectious component in the etiology of PE mirrors that for

  6. Energy efficient engine component development and integration program

    NASA Technical Reports Server (NTRS)

    1982-01-01

    The objective of the Energy Efficient Engine Component Development and Integration program is to develop, evaluate, and demonstrate the technology for achieving lower installed fuel consumption and lower operating costs in future commercial turbofan engines. Minimum goals have been set for a 12 percent reduction in thrust specific fuel consumption (TSFC), 5 percent reduction in direct operating cost (DOC), and 50 percent reduction in performance degradation for the Energy Efficient Engine (flight propulsion system) relative to the JT9D-7A reference engine. The Energy Efficienct Engine features a twin spool, direct drive, mixed flow exhaust configuration, utilizing an integrated engine nacelle structure. A short, stiff, high rotor and a single stage high pressure turbine are among the major enhancements in providing for both performance retention and major reductions in maintenance and direct operating costs. Improved clearance control in the high pressure compressor and turbines, and advanced single crystal materials in turbine blades and vanes are among the major features providing performance improvement. Highlights of work accomplished and programs modifications and deletions are presented.

  7. Development of components for waste management systems using aerospace technology

    SciTech Connect

    Rousar, D.; Young, M.; Sieger, A.

    1995-09-01

    An aerospace fluid management technology called ``platelets`` has been applied to components that are critical to the economic operation of waste management systems. Platelet devices are made by diffusion bonding thin metal plates which have been etched with precise flow passage circuitry to control and meter fluid to desired locations. Supercritical water oxidation (SCWO) is a promising waste treatment technology for safe and environmentally acceptable destruction of hazardous wastes. Performance and economics of current SCWO systems are limited by severe salt deposition on and corrosion of the reactor walls. A platelet transpiring-wall reactor has been developed that provides a protective layer of water adjacent to the reactor walls which prevents salt deposition and corrosion. Plasma arc processing is being considered as a method for stabilizing mixed radioactive wastes. Plasma arc torch systems currently require frequent shutdown to replace failed electrodes and this increases operating costs. A platelet electrode design was developed that has more than 10 times the life of conventional electrodes. It has water cooling channels internal to the electrode wall and slots through the wall for injecting gas into the arc.

  8. COMPONENT DEVELOPMENT NEEDS FOR THE HYBRID SULFUR ELECTROLYZER

    SciTech Connect

    Hobbs, D; Hector Colon-Mercado, H; Mark Elvington, M

    2008-05-30

    Fiscal year 2008 studies in electrolyzer component development have focused on the characterization of membrane electrode assemblies (MEA) after performance tests in the single cell electrolyzer, evaluation of electrocatalysts and membranes using a small scale electrolyzer and evaluating the contribution of individual cell components to the overall electrochemical performance. Scanning electron microscopic (SEM) studies of samples taken from MEAs testing in the SRNL single cell electrolyzer test station indicates a sulfur-rich layer forms between the cathode catalyst layer and the membrane. Based on a review of operating conditions for each of the MEAs evaluated, we conclude that the formation of the layer results from the reduction of sulfur dioxide as it passes through the MEA and reaches the catalyst layer at the cathode-membrane interface. Formation of the sulfur rich layer results in partial delamination of the cathode catalyst layer leading to diminished performance. Furthermore we believe that operating the electrolyzer at elevated pressure significantly increases the rate of formation due to increased adsorption of hydrogen on the internal catalyst surface. Thus, identification of a membrane that exhibits much lower transport of sulfur dioxide is needed to reduce the quantity of sulfur dioxide that reaches the cathode catalyst and is reduced to produce the sulfur-rich layer. Three candidate membranes are currently being evaluated that have shown promise from preliminary studies, (1) modified Nafion{reg_sign}, (2) polybenzimidazole (PBI), and (3) sulfonated Diels Alder polyphenylene (SDAPP). Testing examined the activity for the sulfur dioxide oxidation of platinum (Pt) and platinum-alloy catalysts in 30 wt% sulfuric acid solution. Linear sweep voltammetry showed an increase in activity when catalysts in which Pt is alloyed with non-noble transition metals such as cobalt and chromium. However when Pt is alloyed with noble metals, such as iridium or ruthenium

  9. Photoprotection: part II. Sunscreen: development, efficacy, and controversies.

    PubMed

    Jansen, Rebecca; Osterwalder, Uli; Wang, Steven Q; Burnett, Mark; Lim, Henry W

    2013-12-01

    In addition to the naturally occurring, physical, and systemic photoprotective agents reviewed in part I, topical ultraviolet radiation filters are an important cornerstone of photoprotection. Sunscreen development, efficacy, testing, and controversies are reviewed in part II of this continuing medical education article.

  10. 28 CFR Appendix I to Part 16 - Components of the Department of Justice

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Avenue, NW., Washington, DC 20530-0001. For all components marked by an asterisk, FOIA and Privacy Act...., Suite 570, Washington, DC 20530-0001. The components are: A Office of the Attorney General * Office of..., Washington, DC 20530-0001 Civil Division, U.S. Department of Justice, 901E Bldg., Room 808, Washington,...

  11. Control Systems for Information Systems Development Projects (Part I)

    ERIC Educational Resources Information Center

    Dickson, Gary W.

    1970-01-01

    Discusses control of management information systems and finds a similarity in management of research and development activity. Part II will appear in AEDS Journal, Volume 4, number 2, December 1970. (JF)

  12. 10 CFR Appendix G to Part 110 - Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Illustrative List of Plasma Separation Enrichment Plant... Appendix G to Part 110—Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export Licensing Authority Note—In the plasma separation process, a plasma of uranium...

  13. 10 CFR Appendix G to Part 110 - Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Illustrative List of Plasma Separation Enrichment Plant... Appendix G to Part 110—Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export Licensing Authority Note—In the plasma separation process, a plasma of uranium...

  14. 10 CFR Appendix G to Part 110 - Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Illustrative List of Plasma Separation Enrichment Plant... Appendix G to Part 110—Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export Licensing Authority Note—In the plasma separation process, a plasma of uranium...

  15. 10 CFR Appendix G to Part 110 - Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Illustrative List of Plasma Separation Enrichment Plant... Appendix G to Part 110—Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export Licensing Authority Note—In the plasma separation process, a plasma of uranium...

  16. 10 CFR Appendix G to Part 110 - Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Illustrative List of Plasma Separation Enrichment Plant... Appendix G to Part 110—Illustrative List of Plasma Separation Enrichment Plant Equipment and Components Under NRC Export Licensing Authority Note: In the plasma separation process, a plasma of uranium...

  17. 10 CFR Appendix O to Part 110 - Illustrative List of Fuel Element Fabrication Plant Equipment and Components Under NRC's Export...

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Illustrative List of Fuel Element Fabrication Plant... Appendix O to Part 110—Illustrative List of Fuel Element Fabrication Plant Equipment and Components Under NRC's Export Licensing Authority Note: Nuclear fuel elements are manufactured from source or...

  18. 10 CFR Appendix O to Part 110 - Illustrative List of Fuel Element Fabrication Plant Equipment and Components Under NRC's Export...

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Illustrative List of Fuel Element Fabrication Plant Equipment and Components Under NRC's Export Licensing Authority O Appendix O to Part 110 Energy NUCLEAR..., grinding and grading will be present. Mixed oxide fuels are handled in glove boxes (or...

  19. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXVI, I--CATERPILLAR LUBRICATION SYSTEMS AND COMPONENTS, II--LEARNING ABOUT BRAKES (PART I).

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE FUNCTIONS OF DIESEL ENGINE LUBRICATION SYSTEMS AND COMPONENTS AND THE PRINCIPLES OF OPERATION OF BRAKE SYSTEMS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) THE NEED FOR OIL, (2) SERVICE CLASSIFICATION OF OILS, (3) CATERPILLAR LUBRICATION SYSTEM COMPONENTS (4)…

  20. Disasters and development: Part 2: Understanding and exploiting disaster-development linkages.

    PubMed

    Stephenson, Rob S; DuFrane, Charles

    2005-01-01

    This lesson is a continuation of Disasters and Development: Part 2: Understanding and Exploiting Disaster-Development Linkages published in Prehospital and Disaster Medicine in Volume 17, Number 3. It identifies the goals of a specific damage mitigation project that can be incorporated into a regular development project and the mechanisms for obtaining the mitigation component of such a project. Mechanisms for assessing the success of such a project are discussed. It stresses the importance of the application of building codes, associated training programs, and more extensive use of zoning regulations in urban development that decrease the population at risk and the likelihood of damage to industrial facilities. Disasters can elevate the development potential of a society at risk for damage from a hazard. The political impact of damage and disruption can be a catalyst for change. Development opportunities often are compromised because of an excessive focus on relief assistance. Interventions designed to mitigate the damage from a given hazard are particularly effective when they focus on areas at particularly high risk for actualization of the hazard. Support from the private sector, including the non-formal sector, is a key element of successful reconstruction management. The period of recovery is an opportunity for general assistance to government with administrative procedures, including enhanced management training programs.

  1. Judicious use of custom development in an open source component architecture

    NASA Astrophysics Data System (ADS)

    Bristol, S.; Latysh, N.; Long, D.; Tekell, S.; Allen, J.

    2014-12-01

    Modern software engineering is not as much programming from scratch as innovative assembly of existing components. Seamlessly integrating disparate components into scalable, performant architecture requires sound engineering craftsmanship and can often result in increased cost efficiency and accelerated capabilities if software teams focus their creativity on the edges of the problem space. ScienceBase is part of the U.S. Geological Survey scientific cyberinfrastructure, providing data and information management, distribution services, and analysis capabilities in a way that strives to follow this pattern. ScienceBase leverages open source NoSQL and relational databases, search indexing technology, spatial service engines, numerous libraries, and one proprietary but necessary software component in its architecture. The primary engineering focus is cohesive component interaction, including construction of a seamless Application Programming Interface (API) across all elements. The API allows researchers and software developers alike to leverage the infrastructure in unique, creative ways. Scaling the ScienceBase architecture and core API with increasing data volume (more databases) and complexity (integrated science problems) is a primary challenge addressed by judicious use of custom development in the component architecture. Other data management and informatics activities in the earth sciences have independently resolved to a similar design of reusing and building upon established technology and are working through similar issues for managing and developing information (e.g., U.S. Geoscience Information Network; NASA's Earth Observing System Clearing House; GSToRE at the University of New Mexico). Recent discussions facilitated through the Earth Science Information Partners are exploring potential avenues to exploit the implicit relationships between similar projects for explicit gains in our ability to more rapidly advance global scientific cyberinfrastructure.

  2. Epilepsy Care in Developing Countries: Part II of II

    PubMed Central

    Birbeck, Gretchen L

    2010-01-01

    Although 80% of people with epilepsy reside in resource poor, developing countries, epilepsy care in these regions remains limited and the majority of epilepsy patients go untreated. Cost-effective, sustainable epilepsy care services, delivering first-line antiepileptic drugs through established primary health care facilities, are needed to decrease these treatment gaps. Neurologists with local experience and knowledge of the culture, who are willing to serve as educators, policy advisors, and advocates, can make a difference. This is Part II of a two-part article. Part I reviewed the burden of epilepsy and the current state of resources for treatment in developing countries, while Part II will now discuss various aspects of care in these countries. PMID:20944819

  3. Cleaning Process Development for Metallic Additively Manufactured Parts

    NASA Technical Reports Server (NTRS)

    Tramel, Terri L.; Welker, Roger; Lowery, Niki; Mitchell, Mark

    2014-01-01

    Additive Manufacturing of metallic components for aerospace applications offers many advantages over traditional manufacturing techniques. As a new technology, many aspects of its widespread utilization remain open to investigation. Among these are the cleaning processes that can be used for post finishing of parts and measurements to verify effectiveness of the cleaning processes. Many cleaning and drying processes and measurement methods that have been used for parts manufactured using conventional techniques are candidates that may be considered for cleaning and verification of additively manufactured parts. Among these are vapor degreasing, ultrasonic immersion and spray cleaning, followed by hot air drying, vacuum baking and solvent displacement drying. Differences in porosity, density, and surface finish of additively manufactured versus conventionally manufactured parts may introduce new considerations in the selection of cleaning and drying processes or the method used to verify their effectiveness. This presentation will review the relative strengths and weaknesses of different candidate cleaning and drying processes as they may apply to additively manufactured metal parts for aerospace applications. An ultrasonic cleaning technique for exploring the cleanability of parts will be presented along with an example using additively manufactured Inconel 718 test specimens to illustrate its use. The data analysis shows that this ultrasonic cleaning approach results in a well-behaved ultrasonic cleaning/extraction behavior. That is, it does not show signs of accelerated cavitation erosion of the base material, which was later confirmed by neutron imaging. In addition, the analysis indicated that complete cleaning would be achieved by ultrasonic immersion cleaning at approximately 5 minutes, which was verified by subsequent cleaning of additional parts.

  4. Energy efficient engine component development and integration program

    NASA Technical Reports Server (NTRS)

    1980-01-01

    The design of an energy efficient commercial turbofan engine is examined with emphasis on lower fuel consumption and operating costs. Propulsion system performance, emission standards, and noise reduction are also investigated. A detailed design analysis of the engine/aircraft configuration, engine components, and core engine is presented along with an evaluation of the technology and testing involved.

  5. A Developing Market for Continuing Higher Education: The Reserve Components.

    ERIC Educational Resources Information Center

    Watt, David M.

    Due to increasingly sophisticated military equipment, the Reserve Components of the armed forces need to raise the educational standards for recruits. A number of U.S. educational institutions have responded to their needs for continuing higher education in the areas of job skill enhancement (such as computer operation), regular courses directly…

  6. The Order of Importance of Component Parts of the Biblical Worldview in Christian High School Students

    ERIC Educational Resources Information Center

    Van Meter, Kenneth G.

    2009-01-01

    This micro-ethnographic study is an exploration of the relative degree of importance of the several components of a worldview as articulated by a purposive sample of fourteen upper division students currently enrolled in advance placement classes in ACSI and WASC accredited Christian high schools in Northern California. The research design uses an…

  7. 14 CFR Appendix D to Part 417 - Flight Termination Systems, Components, Installation, and Monitoring

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... monitoring. Non-operating and operating environments include temperature, vibration, shock, acceleration... environments. A thermal cycle must begin with the component at ambient temperature. The cycle must continue as... temperature. Each cycle, including all dwell times, must be continuous without interruption by any...

  8. 49 CFR Appendix A to Part 215 - Railroad Freight Car Components

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    .... Dresser (Symington) Birdsboro Lenoir car works 21183-B BO 5234 1458 CS-184. 1468 21183-N BO 5263 1471 CS... 49 Transportation 4 2013-10-01 2013-10-01 false Railroad Freight Car Components A Appendix A to... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Pt. 215, App. A Appendix A...

  9. 49 CFR Appendix A to Part 215 - Railroad Freight Car Components

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    .... Dresser (Symington) Birdsboro Lenoir car works 21183-B BO 5234 1458 CS-184. 1468 21183-N BO 5263 1471 CS... 49 Transportation 4 2014-10-01 2014-10-01 false Railroad Freight Car Components A Appendix A to... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Pt. 215, App. A Appendix A...

  10. 49 CFR Appendix A to Part 215 - Railroad Freight Car Components

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    .... Dresser (Symington) Birdsboro Lenoir car works 21183-B BO 5234 1458 CS-184. 1468 21183-N BO 5263 1471 CS... 49 Transportation 4 2012-10-01 2012-10-01 false Railroad Freight Car Components A Appendix A to... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Pt. 215, App. A Appendix A...

  11. Manual development: A strategy for identifying core components of integrated health programs.

    PubMed

    Mooss, Angela; Hartman, Megan; Ibañez, Gladys

    2015-12-01

    Integrated care models are gaining popularity as a clinical strategy to reduce costs and improve client outcomes; however, implementation of such complex models requires an understanding of programmatic core components essential to producing positive outcomes. To promote this understanding, evaluators can work collaboratively with organization staff and leaderships to gather information on program implementation, adaptations, organizational buy-in, and project outcomes. In 2011, SAMHSA funded two Miami health clinics to implement integrated care models in co-located settings. Changes in the federal healthcare landscape, non-Medicaid expansion for Florida, and the complexity of projects goals led evaluators to facilitate a core component review as part of evaluation. A manual was developed throughout the project and captured a description, adaptations, inputs needed, lessons learned, and sustainability for each integrated care component. To increase chances for program success, evaluators should institute a method to better define core components of new programs and implementation adaptations, while keeping program replication in mind. Breaking down the program structurally gave the evaluation utility for stakeholders, and ultimately served as a resource for organizations to better understand their program model. The manual also continues to serve as a dissemination and replication source for other providers looking to implement integrated care.

  12. What Not To Do: Anti-patterns for Developing Scientific Workflow Software Components

    NASA Astrophysics Data System (ADS)

    Futrelle, J.; Maffei, A. R.; Sosik, H. M.; Gallager, S. M.; York, A.

    2013-12-01

    software components developed by programmers with widely varying levels of expertise, and have been able to discover and characterize a number of anti-patterns. Our evaluation methodology and testbed have also enabled us to assess the efficacy of strategies to address these anti-patterns according to scientifically relevant metrics, such as ability of algorithms to perform faster than the rate of data acquisition and the accuracy of workflow component output relative to ground truth. The set of anti-patterns and solutions we have identified augments of the body of more well-known software engineering anti-patterns by addressing additional concerns that obtain when a software component has to function as part of a workflow assembled out of independently-developed codebases. Our experience shows that identifying and resolving these anti-patterns reduces development time and improves performance without reducing component reusability.

  13. Research and Development: A Complex Relationship Part I [and] Part II.

    ERIC Educational Resources Information Center

    Pollard, John Douglas Edward

    Part 1 of this document describes the background, format, and early groundwork that went into the development of a test sponsored entirely by private enterprise. The discipline imposed by a financial bottom line imposes special pressures but also offers new opportunities. This private enterprise model is a multi-constructional process where…

  14. Interim report re: component parts for proton-exchange membrane fuel cells

    SciTech Connect

    George Marchetti

    1999-10-01

    The purpose of the first phase of the grant project is to design, develop and test a simplified fuel cell electrode structure for use in proton-exchange membrane fuel cells (''PEMFC''). By simplifying the structure of the electrode, mass production manufacturing efficiencies can be brought into play which will result in significant cost reductions for this fuel cell component. With a reduction in the cost of this key fuel cell component overall costs for PEMFC's can be brought within the commercialization target range of about US$100 per kilowatt for the fuel cell stack. Fuel cell electrodes are necessarily ''multi-layered'' composites. Multi-layers are required because of the several functions that the electrode must be able to perform in the working PEM fuel cell. The current generation of state-of-the-art porous fuel cell electrodes for PEMFC's is comprised of three primary layers. The first layer is the catalyst layer. Since hydrogen is the fuel used in this project and air is used as the oxidant, the catalyst must be capable of adsorbing hydrogen and oxygen from the air. While work is constantly on-going with respect to new hydrogen or oxygen catalysts, the best available catalyst at present for both of the reactant gases is platinum. To be effective, the catalyst (1) must be exposed to a constant flow of the respective reactant gas; (2) must be in intimate contact with the proton-exchange membrane; and (3) must be a finely divided catalyst and have a large specific surface area, especially on the oxidant side where the electrochemical reaction is slower by several orders of magnitude. The second layer is the substrate layer. The substrate layer provides structural support for the finely divided catalyst. It also functions as an electronic junction for conducting electricity produced by the electrochemical reaction from the catalyst layer to the bipolar plate of the fuel cell. In state-of-the-art PEMFC's, this layer is comprised of carbon particles (onto which

  15. Advanced manufacturing development of a composite empennage component for L-1011 aircraft

    NASA Technical Reports Server (NTRS)

    Alva, T.; Henkel, J.; Johnson, R.; Carll, B.; Jackson, A.; Mosesian, B.; Brozovic, R.; Obrien, R.; Eudaily, R.

    1982-01-01

    This is the final report of technical work conducted during the fourth phase of a multiphase program having the objective of the design, development and flight evaluation of an advanced composite empennage component manufactured in a production environment at a cost competitive with those of its metal counterpart, and at a weight savings of at least 20 percent. The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes front and rear spars. During Phase 4 of the program, production quality tooling was designed and manufactured to produce three sets of covers, ribs, spars, miscellaneous parts, and subassemblies to assemble three complete ACVF units. Recurring and nonrecurring cost data were compiled and documented in the updated producibility/design to cost plan. Nondestruct inspections, quality control tests, and quality acceptance tests were performed in accordance with the quality assurance plan and the structural integrity control plan. Records were maintained to provide traceability of material and parts throughout the manufacturing development phase. It was also determined that additional tooling would not be required to support the current and projected L-1011 production rate.

  16. Progress in the development of energy efficient engine components

    NASA Technical Reports Server (NTRS)

    Bucy, R. W.

    1982-01-01

    Component test results are presented for the NASA Energy Efficient Engine program, whose design goals relative to the CF6-50C reference engine include a 12% reduction in specific fuel consumption, 5% reduction in direct operating costs, and 50% reduction in specific fuel consumption deterioration rate over the course of commercial service. Emphasis is placed on the engine's high pressure compressor, which has a design pressure ratio of 23:1, and has completed a series of component tests whose resulting configuration is expected to meet all major objectives of the program. Descriptions are given of the core engine and integrated core/low spool tests, and system test benefits are discussed. Attention is given to the design features of the engine's double annular combustor, high and low pressure air turbines, and scale model exhaust mixer.

  17. Development of Lightweight Prime Power Source Components for Pulsed Applications

    DTIC Science & Technology

    1991-06-01

    lbs, 22 11 long, 18" diameter, 7 lbsjsec mass flow rate, 1, 700 degree F turbine inlet temperature. (1] ALTERNATOR CONSIDERATIONS The choice of...provides an overview of system integration for the 1 MW power source components and power source integration with the pulsed load . This will...indicated that peak power flow into the capacitor occurs about midway through the charge cycle. The varying power flow gives rise to cyclic

  18. Analysis and Modeling of the Galvanic Skin Response Spontaneous Component in the context of Intelligent Biofeedback Systems Development

    NASA Astrophysics Data System (ADS)

    Unakafov, A.

    2009-01-01

    The paper presents an approach to galvanic skin response (GSR) spontaneous component analysis and modeling. In the study a classification of biofeedback training methods is given, importance of intelligent methods development is shown. The INTENS method, which is perspective for intellectualization, is presented. An important problem of biofeedback training method intellectualization - estimation of the GSR spontaneous component - is solved in the main part of the work. Its main characteristics are described; results of GSR spontaneous component modeling are shown. Results of small research of an optimum material for GSR probes are presented.

  19. 14 CFR Appendix D to Part 417 - Flight Termination Systems, Components, Installation, and Monitoring

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... propulsion system that has the capability of reaching a populated or other protected area, incapable of propulsion, without significant lateral or longitudinal deviation in the impact point. This includes each stage and any strap on motor or propulsion system that is part of any payload; (2) Terminate the...

  20. 14 CFR Appendix D to Part 417 - Flight Termination Systems, Components, Installation, and Monitoring

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... propulsion system that has the capability of reaching a populated or other protected area, incapable of propulsion, without significant lateral or longitudinal deviation in the impact point. This includes each stage and any strap on motor or propulsion system that is part of any payload; (2) Terminate the...

  1. 14 CFR Appendix D to Part 417 - Flight Termination Systems, Components, Installation, and Monitoring

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... propulsion system that has the capability of reaching a populated or other protected area, incapable of propulsion, without significant lateral or longitudinal deviation in the impact point. This includes each stage and any strap on motor or propulsion system that is part of any payload; (2) Terminate the...

  2. 14 CFR Appendix D to Part 417 - Flight Termination Systems, Components, Installation, and Monitoring

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... propulsion system that has the capability of reaching a populated or other protected area, incapable of propulsion, without significant lateral or longitudinal deviation in the impact point. This includes each stage and any strap on motor or propulsion system that is part of any payload; (2) Terminate the...

  3. 76 FR 13928 - Amendment to the International Traffic in Arms Regulations: Replacement Parts/Components and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-15

    ... ITAR coverage to where diversion of the embedded defense article is a realistic and practical concern... replacement parts when they are embedded into a larger assembly such that they can be removed without... rule to cover defense articles embedded into ``a higher level assembly that is not an end...

  4. Integration of Multiple Components in Polystyrene-based Microfluidic Devices Part 1: Fabrication and Characterization

    PubMed Central

    Johnson, Alicia S.; Anderson, Kari B.; Halpin, Stephen T.; Kirkpatrick, Douglas C.; Spence, Dana M.; Martin, R. Scott

    2012-01-01

    In Part I of a two-part series, we describe a simple, and inexpensive approach to fabricate polystyrene devices that is based upon melting polystyrene (from either a Petri dish or powder form) against PDMS molds or around electrode materials. The ability to incorporate microchannels in polystyrene and integrate the resulting device with standard laboratory equipment such as an optical plate reader for analyte readout and micropipettors for fluid propulsion is first described. A simple approach for sample and reagent delivery to the device channels using a standard, multi-channel micropipette and a PDMS-based injection block is detailed. Integration of the microfluidic device with these off-chip functions (sample delivery and readout) enables high throughput screens and analyses. An approach to fabricate polystyrene-based devices with embedded electrodes is also demonstrated, thereby enabling the integration of microchip electrophoresis with electrochemical detection through the use of a palladium electrode (for a decoupler) and carbon-fiber bundle (for detection). The device was sealed against a PDMS-based microchannel and used for the electrophoretic separation and amperometric detection of dopamine, epinephrine, catechol, and 3,4-dihydroxyphenylacetic acid. Finally, these devices were compared against PDMS-based microchips in terms of their optical transparency and absorption of an anti-platelet drug, clopidogrel. Part I of this series lays the foundation for Part II, where these devices were utilized for various on-chip cellular analysis. PMID:23120747

  5. Sediment studies at Bikini Atoll part 1. distribution of fine and coarse components in surface sediments

    SciTech Connect

    Noshkin, V. E.; Eagle, R.J.; Robison, W.L.

    1997-01-01

    In 1979, 21 years after the moratorium on nuclear testing in the Marshall Islands, surface sediment samples (to depths of 2 and 4 cm) were collected from 87 locations over the floor of Bikini lagoon. The main purpose for the collections was to map the distribution of long- lived man-made radionuclides associated with the bottom material. In addition the samples were processed to estimate the fraction of fine and coarse components to show what modifications occurred since the sediment composition was first described in samples collected before testing in 1946. In this report a comparison is made of the amount and distribution of fine material associated with the lagoon surface sediment before and after the testing of nuclear devices. Nuclear testing produced more finely divided material in-the surface sediment layer over large areas of the lagoon and especially in regions of the lagoon and reef adjacent to test sites. Five cratering events at Bikini Atoll generated sufficient material to account for the inventory of new fine material found over the bottom surface of the lagoon. Although the fraction of fine material in the bottom sediments was altered by the nuclear events, the combined processes of formation, transport and deposition were not sufficiently dynamic to alter the geographical features of the major sedimentary components over most of the lagoon floor.

  6. Capacity building in water demand management as a key component for attaining millennium development goals

    NASA Astrophysics Data System (ADS)

    Gumbo, Bekithemba; Forster, Laura; Arntzen, Jaap

    Successful water demand management (WDM) implementation as a component of integrated water resource management (IWRM) can play a significant role in the alleviation of poverty through more efficient use of available water resources. The urban population in Southern African cities is characterised by so-called ‘water poor’ communities who typically expend a high percentage of their household income on poor quality water. Usually they have no access to an affordable alternative source. Although WDM as a component of IWRM is not a panacea for poverty, it can help alleviate poverty by facilitating water services management by municipal water supply agencies (MWSAs) in the region. WDM is a key strategy for achieving the millennium development goals (MDGs) and, as such, should be given due attention in the preparation of national IWRM and water efficiency plans. Various studies in the Southern African region have indicated that capacity building is necessary for nations to develop IWRM and water-use efficiency plans to meet the targets set out in the MDGs. WDM education and training of water professionals and end-users is particularly important in developing countries, which are resource and information-access poor. In response to these findings, The World Conservation Union (IUCN) and its consulting partners, the Training and Instructional Design Academy of South Africa (TIDASA), and Centre for Applied Research (CAR) designed, developed and presented a pilot WDM Guideline Training Module for MWSAs as part of Phase II of IUCN’s Southern Africa regional WDM project. Pilot training was conducted in July 2004 in Lusaka, Zambia for a group of 36 participants involved in municipal water supply from nine Southern African countries. This paper looks at the links between building the capacity of professionals, operational staff and other role-players in the municipal water supply chain to implement WDM as part of broader IWRM strategies, and the subsequent potential for

  7. Professional Development as a Critical Component of Continuing Teacher Quality

    ERIC Educational Resources Information Center

    Phillips, Paulina

    2008-01-01

    Professional Development is critical for improving and maintaining teacher quality and the effect flows on into the classroom. Factors influencing the success of Professional Development activities include potential for workplace change, the diverse effect and understanding of adult learning principles, subject specificity, effective mentoring and…

  8. Incorporating an Applied Economic Development Component into a Geography Curriculum.

    ERIC Educational Resources Information Center

    Kale, Steven R.

    1989-01-01

    Discusses how applied economic development has been integrated into the economic geography curriculum at Oregon State University (Corvallis). States that coursework in applied economic development should lead to greater understanding of the causes of economic change, the problems associated with growth or decline, and methods for achieving…

  9. Recreation as a Component of the Community Youth Development System

    ERIC Educational Resources Information Center

    Outley, Corliss; Bocarro, Jason N.; Boleman, Chris T.

    2011-01-01

    Youth today develop within nested systems that either positively or negatively influence their development. Recent research shows that American youth have made tremendous progress: fewer teen births, fewer youth who are heavy drinkers or smokers, and more students completing high school. However, data also indicate that the number of youth living…

  10. Software Engineering: A New Component for Instructional Software Development.

    ERIC Educational Resources Information Center

    Chen, J. Wey; Shen, Chung-Wei

    1989-01-01

    Discussion of software engineering for computer-based instruction (CBI) focuses on a model for instructional software development. Highlights include a multidisciplinary team approach; needs analysis; feasibility study; requirement analysis; prototype construction; design phase; implementation and development; testing and evaluation; and project…

  11. 24 CFR 1000.324 - How is the need component developed?

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false How is the need component developed... URBAN DEVELOPMENT NATIVE AMERICAN HOUSING ACTIVITIES Allocation Formula § 1000.324 How is the need component developed? After determining the FCAS allocation, remaining funds are allocated by need...

  12. Part III: Principal component analysis: bridging the gap between strain, sex and drug effects.

    PubMed

    Keeley, R J; McDonald, R J

    2015-07-15

    Previous work has identified the adolescent period as particularly sensitive to the short- and long-term effects of marijuana and its main psychoactive component Δ9-tetrahydrocannabinol (THC). However, other studies have identified certain backgrounds as more sensitive than others, including the sex of the individual or the strain of the rat used. Further, the effects of THC may be specific to certain behavioural tasks (e.g. measures of anxiety), and the consequences of THC are not seen equally across all behavioural measures. Here, data obtained from adolescent male and female Long-Evans and Wistar rats exposed to THC and tested as adults, which, using standard ANOVA testing, showed strain- and sex-specific effects of THC, was analyzed using principal component analysis (PCA). PCA allowed for the examination of the relative contribution of our variables of interest to the variance in the data obtained from multiple behavioural tasks, including the skilled reaching task, the Morris water task, the discriminative fear-conditioning to context task, the elevated plus maze task and the conditioned place preference task to a low dose of amphetamine, as well as volumetric estimates of brain volumes and cfos activation. We observed that early life experience accounted for a large proportion of variance across data sets, although its relative contribution varied across tasks. Additionally, THC accounted for a very small proportion of the variance across all behavioural tasks. We demonstrate here that by using PCA, we were able to describe the main variables of interest and demonstrate that THC exposure had a negligible effect on the variance in the data set.

  13. Recreation as a component of the community youth development system.

    PubMed

    Outley, Corliss; Bocarro, Jason N; Boleman, Chris T

    2011-01-01

    In an era of fragmented school systems and budget cuts, many educators and youth leaders seeking to solve the problems that youth face are turning to out-of-school-time programs. In many communities, these programs are seen as essential in the development of youth into fully functioning adults. One such area of the out-of-school-time sector is the provision of recreation services. Recreational services have a vital role in connecting youth to their communities, as well as enabling youth and adult allies to improve challenging conditions. This chapter outlines the historical role that recreation has played in community youth development programs and shows how community youth development has evolved. It then looks at how organizations in three communities--the Youthline Outreach Mentorship program in Minneapolis, a 4-H initiative in Parker City, Texas, and the Hockey Is for Everyone program--have successfully applied the theoretical knowledge. Best practices from these programs illustrate that the role of recreation in community youth development is changing. No longer are recreation programs about providing just "fun and games." Recreation organizations are now placing more value on the development of the community as a whole, in addition to the individual well-being of young people.

  14. Ceramic component development analysis -- Volume 1. Final report

    SciTech Connect

    Boss, D.E.

    1998-06-09

    The development of advanced filtration media for advanced fossil-fueled power generating systems is a critical step in meeting the performance and emissions requirements for these systems. While porous metal and ceramic candle-filters have been available for some time, the next generation of filters will include ceramic-matrix composites (CMCs) (Techniweave/Westinghouse, Babcock and Wilcox (B and W), DuPont Lanxide Composites), intermetallic alloys (Pall Corporation), and alternate filter geometries (CeraMem Separations). The goal of this effort was to perform a cursory review of the manufacturing processes used by 5 companies developing advanced filters from the perspective of process repeatability and the ability for their processes to be scale-up to produce volumes. Given the brief nature of the on-site reviews, only an overview of the processes and systems could be obtained. Each of the 5 companies had developed some level of manufacturing and quality assurance documentation, with most of the companies leveraging the procedures from other products they manufacture. It was found that all of the filter manufacturers had a solid understanding of the product development path. Given that these filters are largely developmental, significant additional work is necessary to understand the process-performance relationships and projecting manufacturing costs.

  15. Energy efficient engine component development and integration program

    NASA Technical Reports Server (NTRS)

    1982-01-01

    The development of the technology to improve energy efficiency of propulsion systems for subsonic commercial aircrafts was examined. Goals established include: (1) fuel consumption, reduction in flight propulsion system; (2) direct operation cost; (3) noise, with provision for engine growth corresponding to future engine application; and (4) emissions, EPA new engine standards.

  16. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT VIII. ENGINE COMPONENTS--PART I.

    ERIC Educational Resources Information Center

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE CONSTRUCTION AND MAINTENANCE OF DIESEL ENGINE CYLINDER HEADS AND CYLINDER ASSEMBLIES. TOPICS ARE CYLINDER ASSEMBLY (LINERS), CYLINDER HEADS, VALVES AND VALVE MECHANISMS, AND PISTON AND PISTON RINGS. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING…

  17. Quick Development Microcomputer System: Training Automatic Components for Electronic Troubleshooting

    DTIC Science & Technology

    1991-06-01

    memory demands. The lack of interaction is counter to the buffer models of short-term memory (e.g., Baddeley 1988, Atkinson & Shiffrin 1968). Fourth, the...term memory models and supports the need for an Intermediate or episodic form of memory . We will be developing a simulation model In the coming year...testing quantitative models of skill acquisition. Richard A. Carlson & Walter Schneider (1987). Learning and using causal rules. Submitted to Memory and

  18. An Analytical Approach to Prioritizing the Development of Seabasing Components

    DTIC Science & Technology

    2007-04-05

    116.8 million. This results in a Cost to Field score of fifty points. Joint Maritime Assault Connector The Joint Maritime Assault Connector ( JMAC ...The most likely design is essentially a “stretched” LCAC, about fifty percent longer than the current version. The JMAC is in the development phase...and is planned to be delivered around 2015, as the SLEP LCACs reach their end- of-life. The Seabasing capabilities of the JMAC are summarized in

  19. Transcriptome analysis elucidates key developmental components of bryozoan lophophore development

    PubMed Central

    Wong, Yue Him; Ryu, Taewoo; Seridi, Loqmane; Ghosheh, Yanal; Bougouffa, Salim; Qian, Pei-Yuan; Ravasi, Timothy

    2014-01-01

    The most recent phylogenomic study suggested that Bryozoa (Ectoprocta), Brachiopoda, and Phoronida are monophyletic, implying that the lophophore of bryozoans, phoronids and brachiopods is a synapomorphy. Understanding the molecular mechanisms of the lophophore development of the Lophophorata clade can therefore provide us a new insight into the formation of the diverse morphological traits in metazoans. In the present study, we profiled the transcriptome of the Bryozoan (Ectoproct) Bugula neritina during the swimming larval stage (SW) and the early (4 h) and late (24 h) metamorphic stages using the Illumina HiSeq2000 platform. Various genes that function in development, the immune response and neurogenesis showed differential expression levels during metamorphosis. In situ hybridization of 23 genes that participate in the Wnt, BMP, Notch, and Hedgehog signaling pathways revealed their regulatory roles in the development of the lophophore and the ancestrula digestive tract. Our findings support the hypothesis that developmental precursors of the lophophore and the ancestrula digestive tract are pre-patterned by the differential expression of key developmental genes according to their fate. This study provides a foundation to better understand the developmental divergence and/or convergence among developmental precursors of the lophophore of bryozoans, branchiopods and phoronids. PMID:25300304

  20. Materials and Component Development for Advanced Turbine Systems

    SciTech Connect

    Alvin, M.A.; Pettit, F.; Meier, G.; Yanar, N.; Chyu, M.; Mazzotta, D.; Slaughter, W.; Karaivanov, V.; Kang, B.; Feng, C.; Chen, R.; Fu, T-C.

    2008-10-01

    In order to meet the 2010-2020 DOE Fossil Energy goals for Advanced Power Systems, future oxy-fuel and hydrogen-fired turbines will need to be operated at higher temperatures for extended periods of time, in environments that contain substantially higher moisture concentrations in comparison to current commercial natural gas-fired turbines. Development of modified or advanced material systems, combined with aerothermal concepts are currently being addressed in order to achieve successful operation of these land-based engines. To support the advanced turbine technology development, the National Energy Technology Laboratory (NETL) has initiated a research program effort in collaboration with the University of Pittsburgh (UPitt), and West Virginia University (WVU), working in conjunction with commercial material and coating suppliers as Howmet International and Coatings for Industry (CFI), and test facilities as Westinghouse Plasma Corporation (WPC) and Praxair, to develop advanced material and aerothermal technologies for use in future oxy-fuel and hydrogen-fired turbine applications. Our program efforts and recent results are presented.

  1. Transcriptome analysis elucidates key developmental components of bryozoan lophophore development.

    PubMed

    Wong, Yue Him; Ryu, Taewoo; Seridi, Loqmane; Ghosheh, Yanal; Bougouffa, Salim; Qian, Pei-Yuan; Ravasi, Timothy

    2014-10-10

    The most recent phylogenomic study suggested that Bryozoa (Ectoprocta), Brachiopoda, and Phoronida are monophyletic, implying that the lophophore of bryozoans, phoronids and brachiopods is a synapomorphy. Understanding the molecular mechanisms of the lophophore development of the Lophophorata clade can therefore provide us a new insight into the formation of the diverse morphological traits in metazoans. In the present study, we profiled the transcriptome of the Bryozoan (Ectoproct) Bugula neritina during the swimming larval stage (SW) and the early (4 h) and late (24 h) metamorphic stages using the Illumina HiSeq2000 platform. Various genes that function in development, the immune response and neurogenesis showed differential expression levels during metamorphosis. In situ hybridization of 23 genes that participate in the Wnt, BMP, Notch, and Hedgehog signaling pathways revealed their regulatory roles in the development of the lophophore and the ancestrula digestive tract. Our findings support the hypothesis that developmental precursors of the lophophore and the ancestrula digestive tract are pre-patterned by the differential expression of key developmental genes according to their fate. This study provides a foundation to better understand the developmental divergence and/or convergence among developmental precursors of the lophophore of bryozoans, branchiopods and phoronids.

  2. Integration of Multiple Components in Polystyrene-based Microfluidic Devices Part 2: Cellular Analysis

    PubMed Central

    Anderson, Kari B.; Halpin, Stephen T.; Johnson, Alicia S.; Martin, R. Scott; Spence, Dana M.

    2012-01-01

    In Part II of this series describing the use of polystyrene (PS) devices for microfluidic-based cellular assays, various cellular types and detection strategies are employed to determine three fundamental assays often associated with cells. Specifically, using either integrated electrochemical sensing or optical measurements with a standard multi-well plate reader, cellular uptake, production, or release of important cellular analytes are determined on a PS-based device. One experiment involved the fluorescence measurement of nitric oxide (NO) produced within an endothelial cell line following stimulation with ATP. The result was a four-fold increase in NO production (as compared to a control), with this receptor-based mechanism of NO production verifying the maintenance of cell receptors following immobilization onto the PS substrate. The ability to monitor cellular uptake was also demonstrated by optical determination of Ca2+ into endothelial cells following stimulation with the Ca2+ ionophore A20317. The result was a significant increase (42%) in the calcium uptake in the presence of the ionophore, as compared to a control (17%) (p < 0.05). Finally, the release of catecholamines from a dopaminergic cell line (PC 12 cells) was electrochemically monitored, with the electrodes being embedded into the PS-based device. The PC 12 cells had better adherence on the PS devices, as compared to use of PDMS. Potassium-stimulation resulted in the release of 114 ± 11 µM catecholamines, a significant increase (p < 0.05) over the release from cells that had been exposed to an inhibitor (reserpine, 20 ± 2 µM of catecholamines). The ability to successfully measure multiple analytes, generated in different means from various cells under investigation, suggests that PS may be a useful material for microfluidic device fabrication, especially considering the enhanced cell adhesion to PS, its enhanced rigidity/amenability to automation, and its ability to enable a wider range of

  3. Development of improved coating for advanced carbon-carbon components

    NASA Technical Reports Server (NTRS)

    Yamaki, Y. R.; Brown, J. J.

    1984-01-01

    Reaction sintered silicon nitride (RSSN) was studied as a substitute coating material on the carbon-carbon material (RCC) presently used as a heat shield on the space shuttle, and on advanced carbon-carbon (ACC), a later development. On RCC, RSSN showed potential in a 538 C (1000 F) screening test in which silicon carbide coated material exhibits its highest oxidation rate; RSSN afforded less protection to ACC because of a larger thermal expansion mismatch. Organosilicon densification and metallic silicon sealing methods were studied as means of further increasing the oxidation resistance of the coating, and some improvement was noted when these methods were employed.

  4. Development of metrological NDE methods for microturbine ceramic components

    SciTech Connect

    Lee, H.-R.; Ellingson, W. A.

    1999-12-23

    In this work, X-ray computed tomographic imaging technology with high spatial resolution has been explored for metrological applications to Si{sub 3}N{sub 4} ceramic turbine wheels. X-ray computed tomography (XCT) data were acquired by a charge-coupled device detector coupled to an image intensifier. Cone-beam XCT reconstruction algorithms were used to allow full-volume data acquisition from the turbine wheels. Special software was developed so that edge detection and complex blade contours could be determined from the XCT data. The feasibility of using the XCT for dimensional analyses was compared with that of a coordinate-measuring machine. Details of the XCT system, data acquisition, and dimensional comparisons will be presented.

  5. Seal Technology Development for Advanced Component for Airbreathing Engines

    NASA Technical Reports Server (NTRS)

    Snyder, Philip H.

    2008-01-01

    Key aspects of the design of sealing systems for On Rotor Combustion/Wave Rotor (ORC/WR) systems were addressed. ORC/WR systems generally fit within a broad class of pressure gain Constant Volume Combustors (CVCs) or Pulse Detonation Combustors (PDCs) which are currently being considered for use in many classes of turbine engines for dramatic efficiency improvement. Technology readiness level of this ORC/WR approaches are presently at 2.0. The results of detailed modeling of an ORC/WR system as applied to a regional jet engine application were shown to capture a high degree of pressure gain capabilities. The results of engine cycle analysis indicated the level of specific fuel consumption (SFC) benefits to be 17 percent. The potential losses in pressure gain due to leakage were found to be closely coupled to the wave processes at the rotor endpoints of the ORC/WR system. Extensive investigation into the sealing approaches is reported. Sensitivity studies show that SFC gains of 10 percent remain available even when pressure gain levels are highly penalized. This indicates ORC/WR systems to have a high degree of tolerance to rotor leakage effects but also emphasizes their importance. An engine demonstration of an ORC/WR system is seen as key to progressing the TRL of this technology. An industrial engine was judged to be a highly advantageous platform for demonstration of a first generation ORC/WR system. Prior to such a demonstration, the existing NASA pressure exchanger wave rotor rig was identified as an opportunity to apply both expanded analytical modeling capabilities developed within this program and to identify and fix identified leakage issues existing within this rig. Extensive leakage analysis of the rig was performed and a detailed design of additional sealing strategies for this rig was generated.

  6. Developing the Multimedia User Interface Component (MUSIC) for the Icarus Presentation System (IPS)

    DTIC Science & Technology

    1993-12-01

    AD-A276 341 In-House Report December 1993 DEVELOPING THE MULTIMEDIA USER INTERFACE COMPONENT ( MUSIC ) FOR THE ICARUS PRESENTATION SYSTEM (IPS) Ingrid...DATEs COVERED 7 December 1993 Ina-House Jun - Aug 93 4 TWLE AM SL1sM1E & FUNDING NUMBERS DEVELOPING THE MULTIMEDIA USER INTERFACE COMPONENT ( MUSIC ) PE...the Multimedia User Interface Component ( MUSIC ). This report documents the initial research, design and implementation of a prototype of the MUSIC

  7. MITOCHONDRIAL DISEASES PART II: MOUSE MODELS OF OXPHOS DEFICIENCIES CAUSED BY DEFECTS IN REGULATORY FACTORS AND OTHER COMPONENTS REQUIRED FOR MITOCHONDRIAL FUNCTION

    PubMed Central

    Iommarini, Luisa; Peralta, Susana; Torraco, Alessandra; Diaz, Francisca

    2015-01-01

    Mitochondrial disorders are defined as defects that affect the oxidative phosphorylation system (OXPHOS). They are characterized by a heterogeneous array of clinical presentations due in part to a wide variety of factors required for proper function of the components of the OXPHOS system. There is no cure for these disorders owing our poor knowledge of the pathogenic mechanisms of disease. To understand the mechanisms of human disease numerous mouse models have been developed in recent years. Here we summarize the features of several mouse models of mitochondrial diseases directly related to those factors affecting mtDNA maintenance, replication, transcription, translation as well to other proteins that are involved in mitochondrial dynamics and quality control which affect mitochondrial OXPHOS function without been intrinsic components of the system. We discuss how these models have contributed to our understanding of mitochondrial diseases and their pathogenic mechanisms. PMID:25640959

  8. Analysis of State Applications for Year 4: Planning for the Personnel Components of Part H of IDEA.

    ERIC Educational Resources Information Center

    Bruder, Mary Beth; McCollum, Jeanette

    1991-01-01

    This analysis reports on the plans for special education personnel development by those states submitting fourth year applications under Part H of Public Law 99-457, the Education of the Handicapped Act Amendments (1986). The eight states--Colorado, Hawaii, Idaho, Illinois, Maryland, Montana, North Carolina, and Texas--used a variety of approaches…

  9. Development of disease-resistant rice using regulatory components of induced disease resistance.

    PubMed

    Takatsuji, Hiroshi

    2014-01-01

    Infectious diseases cause huge crop losses annually. In response to pathogen attacks, plants activate defense systems that are mediated through various signaling pathways. The salicylic acid (SA) signaling pathway is the most powerful of these pathways. Several regulatory components of the SA signaling pathway have been identified, and are potential targets for genetic manipulation of plants' disease resistance. However, the resistance associated with these regulatory components is often accompanied by fitness costs; that is, negative effects on plant growth and crop yield. Chemical defense inducers, such as benzothiadiazole and probenazole, act on the SA pathway and induce strong resistance to various pathogens without major fitness costs, owing to their 'priming effect.' Studies on how benzothiadiazole induces disease resistance in rice have identified WRKY45, a key transcription factor in the branched SA pathway, and OsNPR1/NH1. Rice plants overexpressing WRKY45 were extremely resistant to rice blast disease caused by the fungus Magnaporthe oryzae and bacterial leaf blight disease caused by Xanthomonas oryzae pv. oryzae (Xoo), the two major rice diseases. Disease resistance is often accompanied by fitness costs; however, WRKY45 overexpression imposed relatively small fitness costs on rice because of its priming effect. This priming effect was similar to that of chemical defense inducers, although the fitness costs were amplified by some environmental factors. WRKY45 is degraded by the ubiquitin-proteasome system, and the dual role of this degradation partly explains the priming effect. The synergistic interaction between SA and cytokinin signaling that activates WRKY45 also likely contributes to the priming effect. With a main focus on these studies, I review the current knowledge of SA-pathway-dependent defense in rice by comparing it with that in Arabidopsis, and discuss potential strategies to develop disease-resistant rice using signaling components.

  10. Development of a Versatile Ultrasonic Internal Pipe/Vessel Component Monitor for In-Service Inspection of Nuclear Reactor Components

    SciTech Connect

    Searfass, Clifford T.; Malinowski, Owen M.; Van Velsor, Jason K.

    2015-03-22

    The stated goal of this work was to develop a versatile system which could accurately measure vessel and valve internal vibrations and cavitation formation under in-service conditions in nuclear power plants, ultrasonically. The developed technology will benefit the nuclear power generation industry by allowing plant operators to monitor valve and vessel internals during operation. This will help reduce planned outages and plant component failures. During the course of this work, Structural Integrity Associates, Inc. gathered information from industry experts that target vibration amplitudes to be detected should be in the range of 0.001-in to 0.005-in (0.025-mm to 0.127-mm) and target vibration frequency ranges which should be detected were found to be between 0-Hz and 300-Hz. During the performed work, an ultrasonic measuring system was developed which utilized ultrasonic pulse-echo time-of-flight measurements to measure vibration frequency and amplitude. The developed system has been shown to be able to measure vibration amplitudes as low as 0.0008-in (0.020-mm) with vibration frequencies in the range of 17-Hz to 1000-Hz. Therefore, the developed system was able to meet the industry needs for vibration measurement. The developed ultrasonic system was also to be able to measure cavitation formation by monitoring the received ultrasonic time- and frequency-domain signals. This work also demonstrated the survivability of commercially available probes at temperatures up to 300-F for several weeks.

  11. World Development Report, 1980. Part I: Adjustment and Growth in the 1980s. Part II: Poverty and Human Development. Annex: World Development Indicators. With Summary.

    ERIC Educational Resources Information Center

    Isenman, Paul; And Others

    The report, third in a series of annual publications, examines some of the difficulties and prospects in areas of social and economic progress and human development which developing countries face during the next decade. Distinguishing oil-importing from oil-exporting developing countries, the first part of the report presents global and regional…

  12. Development of a wind converter and investigation of its operational function. Part 1: Technical description of the wind energy converter

    NASA Astrophysics Data System (ADS)

    Molly, J. P.; Steinheber, R.

    1982-11-01

    A 10 kW wind energy converter was developed by using as far possible standard serial production parts. The design criteria and the description of the essential machinery components of the MODA 10 wind energy converter are discussed. For some special load cases the safety calculation of the important components is shown. The blade control system which qualified for small wind energy converters, is explained. Weight and cost of the MODA 10 are considered.

  13. Component Development to Accelerate Commercial Implementation of Ultra-Low Emissions Catalytic Combustion

    SciTech Connect

    McCarty, Jon; Berry, Brian; Lundberg, Kare; Anson, Orris

    2003-03-31

    This final report describes a 2000-2003 program for the development of components and processes to enhance the commercialization of ultra-low emissions catalytic combustion in industrial gas turbines. The range of project tasks includes: development of more durable, lower-cost catalysts and catalytic combustor components; development and design of a catalytic pre-burner and a catalytic pilot burner for gas turbines, and on-site fuel conversion processing for utilization of liquid fuel.

  14. Development of Underwater Laser Cladding and Underwater Laser Seal Welding Techniques for Reactor Components (II)

    SciTech Connect

    Masataka Tamura; Shohei Kawano; Wataru Kouno; Yasushi Kanazawa

    2006-07-01

    Stress corrosion cracking (SCC) is one of the major reasons to reduce the reliability of aged reactor components. Toshiba has been developing underwater laser welding onto surface of the aged components as maintenance and repair techniques. Because most of the reactor internal components to apply this underwater laser welding technique have 3-dimensional shape, effect of welding positions and welded shapes are examined and presented in this report. (authors)

  15. DEVELOPMENT OF CAPE-OPEN COMPLIANT PROCESS MODELING COMPONENTS IN MICROSOFT .NET

    EPA Science Inventory

    The CAPE-OPEN middleware standards were created to allow process modeling components (PMCs) developed by third parties to be used in any process modeling environment (PME) utilizing these standards. The CAPE-OPEN middleware specifications were based upon both Microsoft's Compone...

  16. Development and testing of CMC components for automotive gas turbine engines

    NASA Technical Reports Server (NTRS)

    Khandelwal, Pramod K.

    1991-01-01

    Ceramic matrix composite (CMC) materials are currently being developed and evaluated for advanced gas turbine engine components because of their high specific strength and resistance to catastrophic failure. Components with 2D and 3D composite architectures have been successfully designed and fabricated. This is an overview of the test results for a backplate, combustor, and a rotor.

  17. Coil End Parts Development Using BEND and Design for MQXF by LARP

    SciTech Connect

    Yu, Miao; Ambrosio, G.; Bermudez, S. Izquierdo; Bossert, R.; Ferracin, P.; Krave, S.

    2016-09-06

    End parts are critical components for saddle-shaped coils. They have a structural function where the cables are deformed in order to cross over the magnet aperture. Based on the previous design of the US LARP program for 90 mm aperture quadrupoles (TQ/LQ) and 120 mm aperture quadrupoles (HQ/LHQ) using BEND, the coil ends of the low-β quadruples (MQXF) for the HiLumi LHC upgrade were developed. This paper shows the design of the MQXF coil ends, the analysis of the coil ends during the coil fabrication, the autopsy analysis of the coil ends and the feedback to BEND parameters.

  18. Development of glass vitrification at SRL as a waste treatment technique for nuclear weapon components

    SciTech Connect

    Coleman, J.T.; Bickford, D.F.

    1991-01-01

    This report discusses the development of vitrification for the waste treatment of nuclear weapons components at the Savannah River Site. Preliminary testing of surrogate nuclear weapon electronic waste shows that glass vitrification is a viable, robust treatment method.

  19. Development of glass vitrification at SRL as a waste treatment technique for nuclear weapon components

    SciTech Connect

    Coleman, J.T.; Bickford, D.F.

    1991-12-31

    This report discusses the development of vitrification for the waste treatment of nuclear weapons components at the Savannah River Site. Preliminary testing of surrogate nuclear weapon electronic waste shows that glass vitrification is a viable, robust treatment method.

  20. Development of a Real-Time GPS/Seismic Displacement Meter: Seismic Component and Communications

    NASA Astrophysics Data System (ADS)

    Vernon, F.; Bock, Y.

    2002-12-01

    In two abstracts, we report on an ongoing effort to develop an Integrated Real-Time GPS/Seismic System for Orange and Western Riverside Counties, California, spanning three major strike-slip faults in southern California (San Andreas, San Jacinto, and Elsinore) and significant populations and civilian infrastructure. The system relying on existing GPS and seismic networks will collect and analyze GPS and seismic data for the purpose of estimating and disseminating real-time positions and total ground displacements (dynamic, as well as static) covering all phases of the seismic cycle, from fractions of seconds to years. Besides its intrinsic scientific use as a real-time displacement meter (transducer), the GPS/Seismic System will be a powerful tool for local and state decision makers for risk mitigation, disaster management, and structural monitoring (dams, bridges, and buildings). Furthermore, the GPS/Seismic System will become an integral part of California's spatial referencing and positioning infrastructure, which is complicated by tectonic motion, seismic displacements, and land subsidence. This development is taking place under the umbrella of the California Spatial Reference Center, in partnership with local (The Counties, Riverside County Flood and Water Conservation District, Southern California Metropolitan Water District), state (Caltrans), and Federal agencies (NGS, NASA, USGS), the geophysics community (SCEC2/SCIGN), and the private sector (RBF Consulting). The project is leveraging considerable funding, resources, and research and development from SCIGN, CSRC and two NSF-funded IT projects at UCSD and SDSU: RoadNet (Real-Time Observatories, Applications and Data Management Network) and the High Performance Wireless Research and Education Network (HPWREN). These two projects are funded to develop both the wireless networks and the integrated, seamless, and transparent information management system that will deliver seismic, geodetic, oceanographic

  1. Structuring Serendipity: Mentoring as a Component of Leadership Development Programs in Higher Education

    ERIC Educational Resources Information Center

    Bonebright, Denise A.

    2014-01-01

    The need to develop a pool of well-qualified future leaders is a key concern for human resource development scholars and practitioners in higher education. Research indicates that formal leadership development programs are most effective when they are based on experiential models. Mentoring is one experiential component that can enhance such…

  2. Trends and problems in development of the power plants electrical part

    NASA Astrophysics Data System (ADS)

    Gusev, Yu. P.

    2015-03-01

    The article discusses some problems relating to development of the electrical part of modern nuclear and thermal power plants, which are stemming from the use of new process and electrical equipment, such as gas turbine units, power converters, and intellectual microprocessor devices in relay protection and automated control systems. It is pointed out that the failure rates of electrical equipment at Russian and foreign power plants tend to increase. The ongoing power plant technical refitting and innovative development processes generate the need to significantly widen the scope of research works on the electrical part of power plants and rendering scientific support to works on putting in use innovative equipment. It is indicated that one of main factors causing the growth of electrical equipment failures is that some of components of this equipment have insufficiently compatible dynamic characteristics. This, in turn may be due to lack or obsolescence of regulatory documents specifying the requirements for design solutions and operation of electric power equipment that incorporates electronic and microprocessor control and protection devices. It is proposed to restore the system of developing new and updating existing departmental regulatory technical documents that existed in the 1970s, one of the fundamental principles of which was placing long-term responsibility on higher schools and leading design institutions for rendering scientific-technical support to innovative development of components and systems forming the electrical part of power plants. This will make it possible to achieve lower failure rates of electrical equipment and to steadily improve the competitiveness of the Russian electric power industry and energy efficiency of generating companies.

  3. Development of a Novel Brayton-Cycle Cryocooler and Key Component Technologies

    NASA Astrophysics Data System (ADS)

    Nieczkoski, S. J.; Mohling, R. A.

    2004-06-01

    Brayton-cycle cryocoolers are being developed to provide efficient cooling in the 6 K to 70 K temperature range. The cryocoolers are being developed for use in space and in terrestrial applications where combinations of long lifetime, high efficiency, compactness, low mass, low vibration, flexible interfacing, load variability, and reliability are essential. The key enabling technologies for these systems are a mesoscale expander and an advanced oil-free scroll compressor. Both these components are nearing completion of their prototype development phase. The emphasis on the component and system development has been on invoking fabrication processes and techniques that can be evolved to further reduction in scale tending toward cryocooler miniaturization.

  4. A Study On The Practical Application Of Repair Development Methods For Aerospace Components

    NASA Astrophysics Data System (ADS)

    Moedano, Jesus A.

    In the industry of manufacturing, each gas turbine engine component begins in a raw state such as bar stock and is routed through manufacturing processes to define its final form before being installed on the engine. What is the follow-up to this part? What happens when over time and usage it wears? Several factors have created a section of the manufacturing industry known as aftermarket to support the customer in their need for restoration and repair of their original product. Once a product has reached a wear factor or cycle limit that cannot be ignored, one of the options is to have it repaired to maintain use of the core. This research investigated the study into the creation and application of repair development methodology that can be utilized by current and new manufacturing engineers of the world. Those who have been in this field for some time will find the process thought provoking while the engineering students can develop a foundation of thinking to prepare for the common engineering problems they will be tasked to resolve. The examples, figures and tables are true issues of the industry though the data will have been changed due to proprietary factors. The results of the study reveals, under most scenarios, a solid process can be followed to proceed with the best options for repair based on the initial discrepancy. However, this methodology will not be a "catch-all" process but a guidance that will develop the proper thinking in evaluation of the repair options and the possible failure modes of each choice. As with any continuous improvement tool, further research is needed to test the applicability of this process in other fields.

  5. A General Reversible Hereditary Constitutive Model. Part 1; Theoretical Developments

    NASA Technical Reports Server (NTRS)

    Saleeb, A. F.; Arnold, S. M.

    1997-01-01

    Using an internal-variable formalism as a starting point, we describe the viscoelastic extension of a previously-developed viscoplasticity formulation of the complete potential structure type. It is mainly motivated by experimental evidence for the presence of rate/time effects in the so-called quasilinear, reversible, material response range. Several possible generalizations are described, in the general format of hereditary-integral representations for non-equilibrium, stress-type, state variables, both for isotropic as well as anisotropic materials. In particular, thorough discussions are given on the important issues of thermodynamic admissibility requirements for such general descriptions, resulting in a set of explicit mathematical constraints on the associated kernel (relaxation and creep compliance) functions. In addition, a number of explicit, integrated forms are derived, under stress and strain control to facilitate the parametric and qualitative response characteristic studies reported here, as well as to help identify critical factors in the actual experimental characterizations from test data that will be reported in Part II.

  6. The human vomeronasal organ. Part II: prenatal development

    PubMed Central

    SMITH, TIMOTHY D.; BHATNAGAR, KUNWAR P.

    2000-01-01

    During the 20th century, the human vomeronasal organ (VNO) has been controversial regarding its structure, function, and even identity. Despite reports that provide evidence for its presence throughout prenatal and postnatal ontogeny, some studies and numerous textbooks declare its absence in late fetal and postnatal humans. To that end, the present study was designed to establish firmly whether the human VNO is homologous with that of other mammals and whether it degenerates (partially or completely) or persists throughout prenatal development. Fifty human embryos and fetuses (33 d to 32 wk fertilisation age) and 2 neonates were examined by light microscopy. Four embryonic primates (mouse lemurs) were examined for a comparison of VNO embryogenesis. The presence or absence and structural characteristics of the VNO and supporting tissues are described. The first appearance of the VNO was in the form of bilateral epithelial thickenings of the nasal septum, the vomeronasal primordium. The primordia invaginated between 37 and 43 d of age and formed the tubular VNO. The tubular VNO was located dorsally at a variable distance from, but was always spatially separated from the paraseptal cartilages. The mouse lemurs examined in this study and other reports from the literature indicate that the human VNO resembles that of primates having functional VNOs until just after a tubular VNO is formed. Examination of the VNO and adjacent tissues suggested that the VNO may lose receptor cells and corresponding vomeronasal nerves and become a ciliated, pseudostratified epithelium between ∼ 12 and 14 wk of age. Our findings indicate the prenatal human VNO goes through 3 successive stages: early morphogenesis, transformation (of the epithelium), and growth. These observations indicated that (1) all embryonic humans develop a vomeronasal organ which is homologous with the VNOs of other mammals, but which has become displaced and highly variable in relative location during

  7. Toward Interoperable Mesh, Geometry and Field Components for PDE Simulation Development

    SciTech Connect

    Chand, K K; Diachin, L F; Li, X; Ollivier-Gooch, C; Seol, E S; Shephard, M; Tautges, T; Trease, H

    2005-07-11

    Mesh-based PDE simulation codes are becoming increasingly sophisticated and rely on advanced meshing and discretization tools. Unfortunately, it is still difficult to interchange or interoperate tools developed by different communities to experiment with various technologies or to develop new capabilities. To address these difficulties, we have developed component interfaces designed to support the information flow of mesh-based PDE simulations. We describe this information flow and discuss typical roles and services provided by the geometry, mesh, and field components of the simulation. Based on this delineation for the roles of each component, we give a high-level description of the abstract data model and set of interfaces developed by the Department of Energy's Interoperable Tools for Advanced Petascale Simulation (ITAPS) center. These common interfaces are critical to our interoperability goal, and we give examples of several services based upon these interfaces including mesh adaptation and mesh improvement.

  8. 24 CFR 1000.324 - How is the need component developed?

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    .... The need component consists of seven criteria. They are: (a) American Indian and Alaskan Native (AIAN... DEVELOPMENT (CONTINUED) OFFICE OF ASSISTANT SECRETARY FOR PUBLIC AND INDIAN HOUSING, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT NATIVE AMERICAN HOUSING ACTIVITIES Allocation Formula § 1000.324 How is the...

  9. Chemistry research and development. Progress report, December 1978-May 1979. [Component, pilot plant, instrumentation

    SciTech Connect

    Miner, F. J.

    1980-06-30

    Progress and activities are reported on component development, pilot plant development, and instrumentation and statistical systems. Specific items studied include processing of pond sludge, transport of radioactive materials and wastes, corrosion, decontamination and cleaning, fluidized-bed incineration, Pu contamination of soils, chemical analysis, radiometric analysis, security. (DLC)

  10. DEVELOPMENT OF STANDARD AND CORRELATED DIMENSIONS OF MATERIAL-COMPONENTS IN SCHOOL CONSTRUCTION.

    ERIC Educational Resources Information Center

    GRAHAM, LEON R.

    THE OBJECTIVE WAS TO DEVELOP A CORRELATED MODULAR SYSTEM OF SCHOOL DESIGN WHICH WOULD PERMIT A VARIETY OF COMPETITIVE MATERIALS AND EQUIPMENT COMPONENTS TO BE MASS PRODUCED FOR SCHOOLS AND USED INTERCHANGEABLY AND FLEXIBLY. THE DEVELOPED SYSTEM PROPOSES FUNDAMENTAL AND SIGNIFICANT INNOVATIONS WHICH HAVE NOT BEEN ADVANCED BY EARLIER PROGRAMS. THIS…

  11. The Development of a Scale to Explore the Multidimensional Components of Good Student-Teacher Relationships

    ERIC Educational Resources Information Center

    Wilkins, Julia

    2014-01-01

    The Student-Teacher Relationship Survey: Student Version was developed and assessed for factor structure using principal components analysis. No instruments measuring students' perceptions of student-teacher relationships have been developed for high school students, and scales that measure related constructs tend to view good student-teacher…

  12. Gravitational effects on the rearrangement of cytoplasmic components during axial formation in amphibian development

    NASA Astrophysics Data System (ADS)

    Phillips, C. R.; Whalon, B.; Moore, J.; Danilchik, M.

    The spatial positioning of the dorsal-ventral axis in the amphibian, Xenopus laevis, can be experimentally manipulated either by tipping the embryo relative to Earth's gravitational force vector or by centrifugation. Experimental evidence suggests that certain cytoplasmic components are redistributed during the first cell cycle and that these components are, in part, responsible for the establishment of this axis. Further studies indicate that at least some of the cytoplasmic components responsible for establishing this axis may be RNA. Recombinant cDNA and PCR technology are utilized to isolate DNA clones for messenger RNA which becomes spatially localized to the dorsal side of the embryo. These clones are being used to study the mechanisms of spatial localization and the function of the localized RNA transcripts.

  13. Developing interpretable models with optimized set reduction for identifying high risk software components

    NASA Technical Reports Server (NTRS)

    Briand, Lionel C.; Basili, Victor R.; Hetmanski, Christopher J.

    1993-01-01

    Applying equal testing and verification effort to all parts of a software system is not very efficient, especially when resources are limited and scheduling is tight. Therefore, one needs to be able to differentiate low/high fault frequency components so that testing/verification effort can be concentrated where needed. Such a strategy is expected to detect more faults and thus improve the resulting reliability of the overall system. This paper presents the Optimized Set Reduction approach for constructing such models, intended to fulfill specific software engineering needs. Our approach to classification is to measure the software system and build multivariate stochastic models for predicting high risk system components. We present experimental results obtained by classifying Ada components into two classes: is or is not likely to generate faults during system and acceptance test. Also, we evaluate the accuracy of the model and the insights it provides into the error making process.

  14. From Lunar Regolith to Fabricated Parts: Technology Developments and the Utilization of Moon Dirt

    NASA Technical Reports Server (NTRS)

    McLemore, C. A.; Fikes, J. C.; McCarley, K. S.; Good, J. E.; Gilley, S. D.; Kennedy, J. P.

    2008-01-01

    The U.S. Space Exploration Policy has as a cornerstone the establishment of an outpost on the moon. This lunar outpost wil1 eventually provide the necessary planning, technology development, testbed, and training for manned missions in the future beyond the Moon. As part of the overall activity, the National Aeronautics and Space Administration (NASA) is investigating how the in situ resources can be utilized to improve mission success by reducing up-mass, improving safety, reducing risk, and bringing down costs for the overall mission. Marshall Space Flight Center (MSFC), along with other NASA centers, is supporting this endeavor by exploring how lunar regolith can be mined for uses such as construction, life support, propulsion, power, and fabrication. An infrastructure capable of fabrication and nondestructive evaluation will be needed to support habitat structure development and maintenance, tools and mechanical parts fabrication, as well as repair and replacement of space-mission hardware such as life-support items, vehicle components, and crew systems, This infrastructure will utilize the technologies being developed under the In Situ Fabrication and Repair (ISFR) element, which is working in conjunction with the technologies being developed under the In Situ Resources Utilization (ISRU) element, to live off the land. The ISFR Element supports the Space Exploration Initiative by reducing downtime due to failed components; decreasing risk to crew by recovering quickly from degraded operation of equipment; improving system functionality with advanced geometry capabilities; and enhancing mission safety by reducing assembly part counts of original designs where possible. This paper addresses the need and plan for understanding the properties of the lunar regolith to determine the applicability of using this material in a fabrication process. This effort includes the development of high fidelity simulants that will be used in fabrication processes on the ground to

  15. Simulating the Response of a Composite Honeycomb Energy Absorber. Part 1; Dynamic Crushing of Components and Multi-Terrain Impacts

    NASA Technical Reports Server (NTRS)

    Jackson, Karen E.; Fasanella, Edwin L.; Polanco, Michael A.

    2012-01-01

    This paper describes the experimental and analytical evaluation of an externally deployable composite honeycomb structure that is designed to attenuate impact energy during helicopter crashes. The concept, designated the Deployable Energy Absorber (DEA), utilizes an expandable Kevlar (Registered Trademark) honeycomb to dissipate kinetic energy through crushing. The DEA incorporates a unique flexible hinge design that allows the honeycomb to be packaged and stowed until needed for deployment. Experimental evaluation of the DEA included dynamic crush tests of multi-cell components and vertical drop tests of a composite fuselage section, retrofitted with DEA blocks, onto multi-terrain. Finite element models of the test articles were developed and simulations were performed using the transient dynamic code, LSDYNA (Registered Trademark). In each simulation, the DEA was represented using shell elements assigned two different material properties: Mat 24, an isotropic piecewise linear plasticity model, and Mat 58, a continuum damage mechanics model used to represent laminated composite fabrics. DEA model development and test-analysis comparisons are presented.

  16. Development and testing of hermetic, laser-ignited pyrotechnic and explosive components

    NASA Technical Reports Server (NTRS)

    Kramer, Daniel P.; Beckman, Thomas M.; Spangler, Ed M.; Munger, Alan C.; Woods, C. M.

    1993-01-01

    During the last decade there has been increasing interest in the use of lasers in place of electrical systems to ignite various pyrotechnic and explosive materials. The principal driving force for this work was the requirement for safer energetic components which would be insensitive to electrostatic and electromagnetic radiation. In the last few years this research has accelerated since the basic concepts have proven viable. At the present time it is appropriate to shift the research emphasis in laser initiation from the scientific arena--whether it can be done--to the engineering realm--how it can be put into actual practice in the field. Laser initiation research and development at EG&G Mound was in three principal areas: (1) laser/energetic material interactions; (2) development of novel processing techniques for fabricating hermetic (helium leak rate of less than 1 x 10(exp -8) cu cm/s) laser components; and (3) evaluation and testing of laser-ignited components. Research in these three areas has resulted in the development of high quality, hermetic, laser initiated components. Examples are presented which demonstrate the practicality of fabricating hermetic, laser initiated explosive or pyrotechnic components that can be used in the next generation of ignitors, actuators, and detonators.

  17. Near term and long term materials issues and development needs for plasma interactive components

    SciTech Connect

    Mattas, R.F.

    1986-01-01

    Plasma interactive components (PICs), including the first wall, limiter blades, divertor collector plates, halo scrapers, and RF launchers, are exposed to high particle fluxes that can result in high sputtering erosion rates and high heat fluxes. In addition, the materials in reactors are exposed to high neutron fluxes which will degrade the bulk properties. This severe environment will limit the materials and designs which can be used in fusion devices. In order to provide a reasonable degree of confidence that plasma interactive components will operate successfully, a comprehensive development program is needed. Materials research and development plays a key role in the successful development of PICs. The range of operating conditions along with a summary of the major issues for materials development is described. The areas covered include plasma/materials interactions, erosion/redeposition, baseline materials properties, fabrication, and irradiation damage effects. Candidate materials and materials development needs in the near term and long term are identified.

  18. 76 FR 71313 - U.S. Automotive Parts and Components Business Development Mission to Russia

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-17

    ... Government officials and decision-makers, one-on-one meetings with potential business partners and site... business partners that match their market interests. Timetable Sunday, April 22 (Moscow, Russia)--Arrive... business partners. The Commercial Service will assist in booking hotels at favorable rates, but...

  19. 76 FR 77974 - U.S. Automotive Parts and Components Business Development Mission to Russia

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-15

    ... Government officials and decisionmakers, one-on-one meetings with potential business partners and site visits... business partners that match their market interests. Timetable Sunday, April 22, Moscow, Russia Arrive... business partners. The Commercial Service will assist in booking hotels at favorable rates, but...

  20. 5 CFR Appendix B to Part 2641 - Agency Components for Purposes of 18 U.S.C. 207(c)

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... effective as of January 1, 1991. Parent: Department of Commerce Components: Bureau of the Census. Bureau of... States Patent and Trademark Office (formerly Patent and Trademark Office). Parent: Department of Defense... Security Agency. Parent: Department of Energy Component: Federal Energy Regulatory Commission....

  1. Enhancing the Mental Health Promotion Component of a Health and Personal Development Programme in Irish Schools

    ERIC Educational Resources Information Center

    Fitzpatrick, Carol; Conlon, Andrea; Cleary, Deirdre; Power, Mike; King, Frances; Guerin, Suzanne

    2013-01-01

    This study set out to examine the impact of a health and personal development programme (the Social, Personal and Health Education Programme) which had been "enhanced" by the addition of a mental health promotion component. Students aged 12-16 years attending 17 secondary schools were randomly allocated as clusters to participate in…

  2. The Components of Effective Professional Development Activities in Terms of Teachers' Perspective

    ERIC Educational Resources Information Center

    Bayar, Adem

    2014-01-01

    Teacher preparedness is linked to student achievement, yet regularly teachers are entering the profession unprepared. In-service training, or professional development activities, are increasingly being used to remedy this situation. There is little agreement regarding exactly what key components should be included in an effective professional…

  3. The Individual Regulation Component of Group Emotional Intelligence: Measure Development and Validation

    ERIC Educational Resources Information Center

    Peterson, Christina Hamme

    2012-01-01

    Counseling work is increasingly conducted in team format. The methods counseling teams use to manage the emotional component of their group life, or their group emotional intelligence, have been proposed as significantly contributing to group member trust, cooperation, and ultimate performance. Item development, exploratory factor analysis, and…

  4. Advanced component development of MCFC technology at M-C Power

    SciTech Connect

    Erickson, D.S.; Haugh, E.J.; Benjamin, T.G.

    1996-12-31

    M-C Power Corporation (MCP) was founded in 1987 to commercialize Molten Carbonate Fuel Cell (MCFC) stacks. The first generation of active area cell components were successfully scaled-up from the 100-cm{sup 2} area laboratory scale to continuous production of commercial-area (1-m) components. These components have been tested in five commercial-area subscale (20-kW) stacks and one commercial-scale (250-kW) stack. The second 250 kW stack is being installed in the power plant for operation in late 1996 and components have already been manufactured for the third 250-kW stack which is scheduled to go on-line in the middle of 1997. Concurrent with commercial-area (1-m{sup 2}) active component manufacturing has been an ongoing effort to develop and test advanced component technologies that will enable MCP to meet its future cost and performance goals. The primary goal is to lower the total cell package cost, while attaining improvements in cell performance and endurance. This work is being completed through analysis of the cost drivers for raw materials and manufacturing techniques. A program is in place to verify the performance of the lower cost materials through pressurized (3 atm) bench scale (100-cm{sup 2}) cell tests. Bench-scale cell testing of advanced active area components has shown that simultaneous cost reduction and improvements in the performance and endurance are attainable. Following performance verification at the bench scale level, scale-up of the advanced component manufacturing processes to commercial-area has been ongoing in the past year. The following sections discuss some of the performance improvements and reductions in cost that have been realized.

  5. Developing standard performance testing procedures for MC&A components at a site

    SciTech Connect

    Scherer, Carolynn

    2010-01-01

    The condition of a nuclear material control and accountability system (MC&A) and its individual components, as with any system combining technical elements, documentation and the human factor, may be characterized through an aggregate of values for the various parameters that determine the system's ability to perform. The MC&A system's status may be functioning effectively, marginally or not functioning based on a summary of the values of the individual parameters. This work included a review of the following elements and subsystems or components for a material control and accountability system: (1) MC&A Elements: Information subsystem, Measurement subsystem, NM access subsystem, including a tamper-indicating device (TID) program, and Automated information-gathering subsystem; and (2) Detecting NM Loses Elements: Inventory differences, Shipper/receiver differences, Confirmatory measurements and differences with accounting data, and TID or seal violations. In order to detect the absence or loss of nuclear material there must be appropriate interactions among the elements and their respective subsystems (from the list above). Additionally this work includes a review of the status of regulatory requirements for the MC&A system components and potential criteria that support the evaluation of the performance of the listed components. The listed components had performance testing algorithms and procedures developed that took into consideration the regulatory criteria. The developed MC&A performance-testing procedures were the basis for a pilot Guide for MC&A Performance Testing at the MBAs of SSC RF IPPE.

  6. Development of RT-components for the M-3 Strawberry Harvesting Robot

    NASA Astrophysics Data System (ADS)

    Yamashita, Tomoki; Tanaka, Motomasa; Yamamoto, Satoshi; Hayashi, Shigehiko; Saito, Sadafumi; Sugano, Shigeki

    We are now developing the strawberry harvest robot called “M-3” prototype robot system under the 4th urgent project of MAFF. In order to develop the control software of the M-3 robot more efficiently, we innovated the RT-middleware “OpenRTM-aist” software platform. In this system, we developed 9 kind of RT-Components (RTC): Robot task sequence player RTC, Proxy RTC for image processing software, DC motor controller RTC, Arm kinematics RTC, and so on. In this paper, we discuss advantages of RT-middleware developing system and problems about operating the RTC-configured robotic system by end-users.

  7. Advanced Environmental Barrier Coating Development for SiC-SiC Ceramic Matrix Composite Components

    NASA Technical Reports Server (NTRS)

    Zhu, Dongming; Harder, Bryan; Bhatt, Ramakrishna; Kiser, Doug; Wiesner, Valerie L.

    2016-01-01

    This presentation reviews the NASA advanced environmental barrier coating (EBC) system development for SiCSiC Ceramic Matrix Composite (CMC) components for next generation turbine engines. The emphasis has been placed on the current design challenges of the 2700F environmental barrier coatings; coating processing and integration with SiCSiC CMCs and component systems; and performance evaluation and demonstration of EBC-CMC systems. This presentation also highlights the EBC-CMC system temperature capability and durability improvements through advanced compositions and architecture designs, as shown in recent simulated engine high heat flux, combustion environment, in conjunction with mechanical creep and fatigue loading testing conditions.

  8. Development of a butterfly multiprocessor test bed description of butterfly components

    NASA Astrophysics Data System (ADS)

    Goodhue, J.; Starr, E.

    1985-03-01

    In this, the first in a series of quarterly technical reports on the development of a 128-node Butterfly (TM) testbed we present descriptions of the major components of the Butterfly Parallel Processor: the Processor Node (BPN), the MSI Switch Node (BSN), the VLSI Switch Node (BVSN), the Butterfly I/O Board (BI1), the Multibus Adapter (BMA), and the Butterfly Fantail (BFAN). At the end of the report, there is a set of tables that summarize the important characteristics of each component.

  9. New developments in investment recovery and parts locating

    SciTech Connect

    Honeywell, A.P. ); Kelly, J.C. )

    1992-01-01

    Electric utilities and other industrial firms are discovering that by establishing special investment recovery groups they can release scarce investment capital tied up in excess spare parts and equipment. Some of these groups have become significant suppliers of material in the industrial equipment marketplace. Experience is showing that the efforts of these groups can potentially produce more profit for their companies per incremental unit of administrative cost than any other arm of a company's operation. The role of investment recovery groups to identify and profitably dispose of excess inventories will become more important, especially within utilities, because public utility agencies are now encouraging, even mandating, inventory reduction and tighter management overall.

  10. White Paper for Streamlined Development of Part 70 Permit Applications

    EPA Pesticide Factsheets

    This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Policy and Guidance Database available at www2.epa.gov/title-v-operating-permits/title-v-operating-permit-policy-and-guidance-document-index. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  11. Development of Hot Isostatically Pressed Rene 95 Turbine Parts

    DTIC Science & Technology

    1977-05-01

    34---.- ~’A4 𔃾 A4 - ’t- Al ’ a % ~ * . Ř lOOX 2000F/15 ksi 50OX Figure~~ ~ 6.. Mirstutue of -60 Mes Vedo B nta.tuyCmat-(he ) -. 4, 38 - .4-I-J En n cn In 0 0... Vedo AAty’ :x&J u-Sud onTs edrAadVno aeil (let) ~4~4 ;147 diameters of each cooling-plate was left intact during heat treatment. All parts were

  12. INDIAN EDUCATION WORKSHOPS. PART I - EDUCATION OF INDIAN ADULTS. PART II - COMMUNITY DEVELOPMENT IN INDIAN EDUCATION.

    ERIC Educational Resources Information Center

    LEE, NICHOLAS, ED.; ROESSEL, ROBERT A., JR., ED.

    DURING THE SUMMER OF 1962, THE INDIAN EDUCATION CENTER OF ARIZONA STATE UNIVERSITY OFFERED TWO COURSES--EDUCATION OF THE INDIAN ADULT AND COMMUNITY DEVELOPMENT IN INDIAN EDUCATION. PAPERS WRITTEN BY STUDENTS IN THE COURSES AND REPORTS OF GUEST SPEAKERS ARE PRESENTED IN THIS VOLUME. TOPICS COVERED INCLUDE ADULT EDUCATION THROUGH PARENT-TEACHER…

  13. Achievement Motivation Development Project. Final Report. Appendix IV, Part 2.

    ERIC Educational Resources Information Center

    McClelland, David C.; Alschuler, Alfred S.

    The Achievement Motivation Development Project is described. The Project has culminated in the development of course materials designed explicitly to promote aspects of psychological growth. As such, it is viewed as but one thrust in an emerging psychological education movement. Achievement motivation is defined as a way of planning, a set of…

  14. Successful Drug Development Despite Adverse Preclinical Findings Part 2: Examples

    PubMed Central

    Kuroda, Junji; Plassmann, Stephanie; Hayashi, Makoto; Prentice, David E.

    2010-01-01

    To illustrate the process of addressing adverse preclinical findings (APFs) as outlined in the first part of this review, a number of cases with unexpected APF in toxicity studies with drug candidates is discussed in this second part. The emphasis is on risk characterization, especially regarding the mode of action (MoA), and risk evaluation regarding relevance for man. While severe APFs such as retinal toxicity may turn out to be of little human relevance, minor findings particularly in early toxicity studies, such as vasculitis, may later pose a real problem. Rodents are imperfect models for endocrine APFs, non-rodents for human cardiac effects. Liver and kidney toxicities are frequent, but they can often be monitored in man and do not necessarily result in early termination of drug candidates. Novel findings such as the unusual lesions in the gastrointestinal tract and the bones presented in this review can be difficult to explain. It will be shown that well known issues such as phospholipidosis and carcinogenicity by agonists of peroxisome proliferator-activated receptors (PPAR) need to be evaluated on a case-by-case basis. The latter is of particular interest because the new PPAR α and dual α/γ agonists resulted in a change of the safety paradigm established with the older PPAR α agonists. General toxicologists and pathologists need some understanding of the principles of genotoxicity and reproductive toxicity testing. Both types of preclinical toxicities are major APF and clinical monitoring is difficult, generally leading to permanent use restrictions. PMID:22272032

  15. Vapour and acid components separation from gases by membranes principles and engineering approach to membranes development

    NASA Astrophysics Data System (ADS)

    Kagramanov, G. G.; Storojuk, I. P.; Farnosova, E. N.

    2016-09-01

    The modern commercially available polymer membranes and membrane modules for purification of gases, containing acid components, simultaneously with dehumidification of treated gas streams, were developed and commercialized in the very end of XXth century. The membranes basic properties - selectivity (separation factor) and permeation flow rates - are relatively far from satisfying the growing and modern-scale industrial need in purification technologies and corresponding equipments. The attempt to formulate the basic principles, scientific and engineering approaches to the development of prospective membranes for the purification of gases, especially such as natural and oil gases, from acid components, simultaneously with drying them, was being made. For this purpose the influence of various factors - polymer nature, membrane type, structure, geometrical and mass-transfer characteristics, etc. - were studied and analyzed in order to formulate the basic principles and demands for development of membranes, capable to withstand successfully the sever conditions of exploitation.

  16. 10 CFR Appendix F to Part 110 - Illustrative List of Laser-Based Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... uranium vaporization systems that contain high-power strip or scanning electron beam guns with a delivered... 10 Energy 2 2014-01-01 2014-01-01 false Illustrative List of Laser-Based Enrichment Plant... Appendix F to Part 110—Illustrative List of Laser-Based Enrichment Plant Equipment and Components Under...

  17. 10 CFR Appendix F to Part 110 - Illustrative List of Laser-Based Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... uranium vaporization systems that contain high-power strip or scanning electron beam guns with a delivered... 10 Energy 2 2013-01-01 2013-01-01 false Illustrative List of Laser-Based Enrichment Plant... Appendix F to Part 110—Illustrative List of Laser-Based Enrichment Plant Equipment and Components Under...

  18. 10 CFR Appendix F to Part 110 - Illustrative List of Laser-Based Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... laser. The laser system for MLIS usually consists of a CO2 or excimer laser and a multi-pass optical... 10 Energy 2 2010-01-01 2010-01-01 false Illustrative List of Laser-Based Enrichment Plant... Appendix F to Part 110—Illustrative List of Laser-Based Enrichment Plant Equipment and Components Under...

  19. EXTENSION OF SELF-MODELING CURVE RESOLUTION TO MIXTURES OF MORE THAN THREE COMPONENTS: PART 2: FINDING THE COMPLETE SOLUTION. (R826238)

    EPA Science Inventory

    The previous paper [R.C. Henry, B.M. Kim, Extension of self-modeling curve resolution to mixtures of more than three components: Part 1. Finding the basic feasible region, Chemometrics and Intelligent Laboratory Systems 8 (1990) 205¯216] explained an extension ...

  20. Three-component competitive adsorption model for fixed-bed and moving-bed granular activated carbon adsorbers. Part II. Model parameterization and verification

    SciTech Connect

    Lance C. Schideman; Benito J. Marinas; Vernon L. Snoeyink; Carlos Campos

    2006-11-01

    COMPSORB-GAC is a 3-component competitive adsorption kinetic model for granular activated carbon (GAC) adsorbers that was developed in Part I of this study, including a proposed procedure for determining model parameters in natural water applications with background natural organic matter (NOM). Part II of this study demonstrates the proposed parameterization procedure and validates the modeling approach by comparing predictions with experimental breakthrough curves at multiple empty-bed contact times for both fixed-bed and moving-bed reactors. The parameterization procedure consists of a set of independent, short-term experimental tests with fresh and batch preloaded adsorbents (using F-400 GAC, a coal-based adsorbent) and then data fitting using both classic and recently developed theoretical expressions. The model and parameterization procedure simplifies NOM into two fictive fractions (pore-blocking and strongly competing) and incorporates three competitive effects that vary both temporally and axially in a GAC column (direct competition for sites, intraparticle pore blockage, and external surface pore blockage). With all three competitive mechanisms accounted for, the model could accurately predict breakthrough profiles for column lengths and durations that were much longer than those used for model parameterization. Model predictions that ignored one or more of the competitive mechanisms showed that each mechanism was important for different regions of the breakthrough curve. The external surface pore-blockage effect was predominant for the prediction of early breakthrough data, whereas direct competition for sites and intraparticle pore blockage were prevalent when predicting higher breakthrough levels and data later in the column run. 22 refs., 10 figs., 2 tabs.

  1. Impacts of climatic changes on carbon and water balance components of boreal forest ecosystems in central part of European Russia

    NASA Astrophysics Data System (ADS)

    Olchev, A.; Novenko, E.; Desherevskaya, O.; Kurbatova, J.

    2009-04-01

    Within the framework of the study the possible impacts of climatic changes on carbon and water balances of boreal forest ecosystems of the central part of European Russia for period up to 2100 was estimated using results of model simulations and field measurements. The boreal forests of the Central Forest State Natural Biosphere Reserve (CFSNBR) were selected for the study. They are located at the southern boundary of south taiga zone in the European part of Russia (Tver region) and it can be expected that they will be very sensitive to modern climate warming. Expected future pattern of climatic parameters in the study area was derived using the global climatic model ECHAM5 (MPI Hamburg, Germany) and climatic scenarios B1, A1B and A2 (IPCC 2007). The possible scenarios of species composition changes of the boreal forests were developed using reconstructions of Holocene vegetation cover and climatic conditions on the base of pollen and plant macrofossil analysis of peat profiles in CFSNBR. The annual future pattern of CO2 and H2O fluxes of the forests were simulated using a process-based Mixfor-SVAT model (Olchev et al. 2002, 2008). The main advantage of Mixfor-SVAT is that it allows us to describe CO2 and H2O fluxes both in mono-specific and mixed forest stands. It is able to quantify both total ecosystem fluxes and flux partitioning among different tree species and canopy layers. It is obvious that it can be very helpful to describe accurately effects of species composition changes on structure of dynamics of carbon and water balance of forest ecosystems. Results of modeling experiments show that expected climatic and vegetation changes can have significant impact on evapotranspiration, transpiration, Net Ecosystem Exchange (NEE), Gross (GPP) and Net (NPP) Primary Productivities of boreal forest ecosystems. These changes have a clear seasonal trend and they are depended on species composition of a forest stand. This study was supported by the Russian Foundation

  2. Developing a Small Scale Preventive Maintenance Program: Part 1.

    ERIC Educational Resources Information Center

    Morris, John M.

    1981-01-01

    The first of two articles outlines how the director of the physical plant at Monroe County Community College (Michigan) developed a preventive maintenance program. The first step, assembling a set of up-to-date records, is detailed. (MLF)

  3. Standardized development of computer software. Part 2: Standards

    NASA Technical Reports Server (NTRS)

    Tausworthe, R. C.

    1978-01-01

    This monograph contains standards for software development and engineering. The book sets forth rules for design, specification, coding, testing, documentation, and quality assurance audits of software; it also contains detailed outlines for the documentation to be produced.

  4. The Cash Flow Budget. Part I--Development

    ERIC Educational Resources Information Center

    Gehm, Rudy

    1978-01-01

    With the cash flow budget a college store manager can prepare himself and the business office to meet current obligations during periods of cash shortfall. Its development is described and guidelines are offered. (LBH)

  5. Materials Evaluation. Part II. Development of Corrosion Inhibitors.

    DTIC Science & Technology

    1979-09-01

    and Identify by block number) A borax -nitrite based inhibitor has been developed for incorporation into the Air Force Rinse Facility at MacDill Air...Block 20 inhibitors has been tested and a borax -nitrite based formulation developed which inhibits the corrosion of several ferrous and nonferrous...alternatives to chromates, one such alternative being a borax -nitrite based inhibitor. The value of borax nitrite as a corrosion inhibitor has long been

  6. Innovation through developing consumers’ community. Part I: Innovation in action

    NASA Astrophysics Data System (ADS)

    Gălăţanu (Avram, E.; Avasilcăi, S.

    2015-11-01

    Technological changes and need for innovation represents the main concerns for organizational growth and profitability. However the main priority is still about achieving high performance through product development and consumers' engagement activities. As implementation of open innovation applications increased and value co — creation became well known and major process, companies were engaged into value co — innovation activities. From this point of view the need for joint efforts with consumers in product development arose. Thus the primary condition for an organization to be consumer centric is to define clear the vision and mission which reflects the common efforts for co — creation and diffusion of innovation. As Research & Development processes evolved and interest for innovative concepts and products arose, companies started to implement the specific instruments for consumers' attraction and engagement into design and product development. The digitalized innovation became the main source for establishing the direct communication with the consumers. In order to achieve organization growth, profitability and recognition, the companies should be aware of the innovation importance and the need for internal change. From this point of view, there is necessary to assess the organizational structures, to implement new policies and to establish strategic targets. Basically it is justified the need for platform occurrence and development. Based on case study of BMW Group, recognised leader in automotive industry for innovative concepts, there will be analysed main features within organizational context which promotes the innovation implementation. There will be provided the review of the BMW Group experience of innovation activities, main consumers' engagement strategies, the values which promote the consumer — centric product development, new opportunities assessment, major policies and concerns. The foreseen result is to understand how companies are

  7. Development of high performance scientific components for interoperability of computing packages

    SciTech Connect

    Gulabani, Teena Pratap

    2008-01-01

    Three major high performance quantum chemistry computational packages, NWChem, GAMESS and MPQC have been developed by different research efforts following different design patterns. The goal is to achieve interoperability among these packages by overcoming the challenges caused by the different communication patterns and software design of each of these packages. A chemistry algorithm is hard to develop as well as being a time consuming process; integration of large quantum chemistry packages will allow resource sharing and thus avoid reinvention of the wheel. Creating connections between these incompatible packages is the major motivation of the proposed work. This interoperability is achieved by bringing the benefits of Component Based Software Engineering through a plug-and-play component framework called Common Component Architecture (CCA). In this thesis, I present a strategy and process used for interfacing two widely used and important computational chemistry methodologies: Quantum Mechanics and Molecular Mechanics. To show the feasibility of the proposed approach the Tuning and Analysis Utility (TAU) has been coupled with NWChem code and its CCA components. Results show that the overhead is negligible when compared to the ease and potential of organizing and coping with large-scale software applications.

  8. Standardized development of computer software. Part 1: Methods

    NASA Technical Reports Server (NTRS)

    Tausworthe, R. C.

    1976-01-01

    This work is a two-volume set on standards for modern software engineering methodology. This volume presents a tutorial and practical guide to the efficient development of reliable computer software, a unified and coordinated discipline for design, coding, testing, documentation, and project organization and management. The aim of the monograph is to provide formal disciplines for increasing the probability of securing software that is characterized by high degrees of initial correctness, readability, and maintainability, and to promote practices which aid in the consistent and orderly development of a total software system within schedule and budgetary constraints. These disciplines are set forth as a set of rules to be applied during software development to drastically reduce the time traditionally spent in debugging, to increase documentation quality, to foster understandability among those who must come in contact with it, and to facilitate operations and alterations of the program as requirements on the program environment change.

  9. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1997--September 30, 1998

    SciTech Connect

    Gibson, J.

    1998-12-01

    During this period, General Atomics (GA) and their partner Schafer Corporation were assigned 17 formal tasks in support of the Inertial Confinement Fusion (ICF) program and its five laboratories. A portion of the effort on these tasks included providing direct ``On-site Support`` at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). They fabricated and delivered over 1,200 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNLA. They produced more than 1,300 glass and plastic target capsules for LLNL, LANL, SNLA, and the University of Rochester/Laboratory for Laser Energetics (UR/LLE). They also delivered nearly 2,000 various target foils and films for Naval Research Lab (NRL) and UR/LLE in FY98. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY98, great progress was made by the GA/Schafer-UR/LLE-LANL team in the design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA. The design phase was concluded for all components of the OCTS and all major components were procured and nearly all were fabricated. Many of the components were assembled and tested, and some have been shipped to UR/LLE. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. They are part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. They also contributed cryogenic support and developed concepts for NIF cryogenic targets. This report summarizes and documents the technical progress made on these tasks.

  10. Insights into Teacher Development: Part I--The Emergent Teacher

    ERIC Educational Resources Information Center

    Berl, Patricia Scallan

    2004-01-01

    The child care workforce is changing. More than ever before, directors must contend with faculty whose educational levels, job expectations, and career aspirations differ widely. Teachers vary in their experience, professional demeanor, stages in career development, and most recently, generational differences that impact the significance and…

  11. Development of a container for handling, testing, and storing discrete microelectronic components

    NASA Technical Reports Server (NTRS)

    Filip, G. L.; Caruso, S. V.

    1972-01-01

    A container has been developed for handling, testing, burning-in, and storing discrete microelectronic components without removal from the protective package. The package was designed to accommodate the leadless inverted device and other carrier-mounted active devices and chip-type discrete resistors and capacitors. Before the indicated development, components were handled and tested in various ways, some of which resulted in damage or contamination. The basic design of the container utilizes precision machined printed circuit boards and chemically milled (photoetched) contact springs. Included in this design for protection is an O-ring-sealed cover. Methods of fabrication and limitations of the current hardware are presented. Current applications of and possible extensions to the technology are discussed.

  12. Development of Sensors for Ceramic Components in Advanced Propulsion Systems. Phase 2; Temperature Sensor Systems Evaluation

    NASA Technical Reports Server (NTRS)

    Atkinson, W. H.; Cyr, M. A.; Strange, R. R.

    1994-01-01

    The 'development of sensors for ceramic components in advanced propulsion systems' program is divided into two phases. The objectives of Phase 1 were to analyze, evaluate and recommend sensor concepts for the measurement of surface temperature, strain and heat flux on ceramic components for advanced propulsion systems. The results of this effort were previously published in NASA CR-182111. As a result of Phase 1, three approaches were recommended for further development: pyrometry, thin-film sensors, and thermographic phosphors. The objective of Phase 2 were to fabricate and conduct laboratory demonstration tests of these systems. Six materials, mutually agreed upon by NASA and Pratt & Whitney, were investigated under this program. This report summarizes the Phase 2 effort and provides conclusions and recommendations for each of the categories evaluated.

  13. Development and empirical validation of symmetric component measures of multidimensional constructs: customer and competitor orientation.

    PubMed

    Sørensen, Hans Eibe; Slater, Stanley F

    2008-08-01

    Atheoretical measure purification may lead to construct deficient measures. The purpose of this paper is to provide a theoretically driven procedure for the development and empirical validation of symmetric component measures of multidimensional constructs. Particular emphasis is placed on establishing a formalized three-step procedure for achieving a posteriori content validity. Then the procedure is applied to development and empirical validation of two symmetrical component measures of market orientation, customer orientation and competitor orientation. Analysis suggests that average variance extracted is particularly critical to reliability in the respecification of multi-indicator measures. In relation to this, the results also identify possible deficiencies in using Cronbach alpha for establishing reliable and valid measures.

  14. Development of a Panel Method for Modeling Configurations with Unsteady Component Motions. Phase 1

    DTIC Science & Technology

    1988-04-15

    significant length scales, the methods rely on the results of existing wake modeling techniques to specify the boundary conditions on their solution...15ANALYTICAL METHODS REPORT 8801 ( I DEVELOPMENT OF A PANEL METHOD FOR MODELING CONFIGURATIONS WITH UNSTEADY COMPONENT MOTIONS PHASE I FINAL REPORT...PREPARED UNDER SEIR CONTRACT DAALO3-87-C-OO11 Lfl Prepared By: David R. Clark & Brian Maskew Analytical Methods Inc. 2133 152nd Avenue N.E. Redmond

  15. Team development, Part 7: Its role at the workplace.

    PubMed

    Mahoney, F X

    1982-01-01

    In this windup of his series on team development (TD), Francis X. Mahoney, personnel development advisor for Exxon Company, U.S.A., sums up TD's advantages, shows how it can be used to meet organizational objectives, and indicates other ways of applying TD methods. Mahoney maintains that TD is truly "organization development (OD) at the front line" because they share the same objectives. For example, employee involvement and encouragement of initiative are OD goals and, as we have seen, TD gets people involved and encourages even those at the lowest level of the organization to contribute ideas and work together to solve work problems and implement the solutions. Mahoney hopes that this series will encourage internal and external OD experts to apply OD at levels not normally reached during regular assignments. TD activities can provide the basis for continuing activities between or after consultants' visits and after training programs. It can become a tool, particularly for first-time supervisors and middle managers, to improve productivity and teamwork. That, in essence, is what this series is all about--getting people to work together productively, effectively, and cohesively.

  16. 5 CFR Appendix B to Part 2641 - Agency Components for Purposes of 18 U.S.C. 207(c)

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Components: Department of the Air Force. Department of the Army. Department of the Navy. Defense Information Systems Agency. Defense Intelligence Agency. Defense Logistics Agency. Defense Threat Reduction Agency (effective February 5, 1999). National Geospatial-Intelligence Agency (formerly National Imagery and...

  17. 10 CFR Appendix H to Part 110 - Illustrative List of Electromagnetic Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... separated ions. Auxiliary systems for the process include the magnet power supply system, the ion source... opening and closure for removal and reinstallation of these components; and (iv) Magnet pole pieces—especially designed or prepared magnet pole pieces having a diameter greater than 2 m used to maintain...

  18. 10 CFR Appendix H to Part 110 - Illustrative List of Electromagnetic Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... separated ions. Auxiliary systems for the process include the magnet power supply system, the ion source... opening and closure for removal and reinstallation of these components; and (iv) Magnet pole pieces—especially designed or prepared magnet pole pieces having a diameter greater than 2 m used to maintain...

  19. 10 CFR Appendix H to Part 110 - Illustrative List of Electromagnetic Enrichment Plant Equipment and Components Under NRC Export...

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... separated ions. Auxiliary systems for the process include the magnet power supply system, the ion source... opening and closure for removal and reinstallation of these components; and (iv) Magnet pole pieces—especially designed or prepared magnet pole pieces having a diameter greater than 2 m used to maintain...

  20. Nutritional components regulate the gut immune system and its association with intestinal immune disease development.

    PubMed

    Lamichhane, Aayam; Kiyono, Hiroshi; Kunisawa, Jun

    2013-12-01

    The gut is equipped with a unique immune system for maintaining immunological homeostasis, and its functional immune disruption can result in the development of immune diseases such as food allergy and intestinal inflammation. Accumulating evidence has demonstrated that nutritional components play an important role in the regulation of gut immune responses and also in the development of intestinal immune diseases. In this review, we focus on the immunological functions of lipids, vitamins, and nucleotides in the regulation of the intestinal immune system and as potential targets for the control of intestinal immune diseases.

  1. Modular and coordinated expression of immune system regulatory and signaling components in the developing and adult nervous system.

    PubMed

    Monzón-Sandoval, Jimena; Castillo-Morales, Atahualpa; Crampton, Sean; McKelvey, Laura; Nolan, Aoife; O'Keeffe, Gerard; Gutierrez, Humberto

    2015-01-01

    During development, the nervous system (NS) is assembled and sculpted through a concerted series of neurodevelopmental events orchestrated by a complex genetic programme. While neural-specific gene expression plays a critical part in this process, in recent years, a number of immune-related signaling and regulatory components have also been shown to play key physiological roles in the developing and adult NS. While the involvement of individual immune-related signaling components in neural functions may reflect their ubiquitous character, it may also reflect a much wider, as yet undescribed, genetic network of immune-related molecules acting as an intrinsic component of the neural-specific regulatory machinery that ultimately shapes the NS. In order to gain insights into the scale and wider functional organization of immune-related genetic networks in the NS, we examined the large scale pattern of expression of these genes in the brain. Our results show a highly significant correlated expression and transcriptional clustering among immune-related genes in the developing and adult brain, and this correlation was the highest in the brain when compared to muscle, liver, kidney and endothelial cells. We experimentally tested the regulatory clustering of immune system (IS) genes by using microarray expression profiling in cultures of dissociated neurons stimulated with the pro-inflammatory cytokine TNF-alpha, and found a highly significant enrichment of immune system-related genes among the resulting differentially expressed genes. Our findings strongly suggest a coherent recruitment of entire immune-related genetic regulatory modules by the neural-specific genetic programme that shapes the NS.

  2. Quantifying nonhomogeneous colors in agricultural materials part I: method development.

    PubMed

    Balaban, M O

    2008-11-01

    Measuring the color of food and agricultural materials using machine vision (MV) has advantages not available by other measurement methods such as subjective tests or use of color meters. The perception of consumers may be affected by the nonuniformity of colors. For relatively uniform colors, average color values similar to those given by color meters can be obtained by MV. For nonuniform colors, various image analysis methods (color blocks, contours, and "color change index"[CCI]) can be applied to images obtained by MV. The degree of nonuniformity can be quantified, depending on the level of detail desired. In this article, the development of the CCI concept is presented. For images with a wide range of hue values, the color blocks method quantifies well the nonhomogeneity of colors. For images with a narrow hue range, the CCI method is a better indicator of color nonhomogeneity.

  3. GSTARS computer models and their applications, part I: theoretical development

    USGS Publications Warehouse

    Yang, C.T.; Simoes, F.J.M.

    2008-01-01

    GSTARS is a series of computer models developed by the U.S. Bureau of Reclamation for alluvial river and reservoir sedimentation studies while the authors were employed by that agency. The first version of GSTARS was released in 1986 using Fortran IV for mainframe computers. GSTARS 2.0 was released in 1998 for personal computer application with most of the code in the original GSTARS revised, improved, and expanded using Fortran IV/77. GSTARS 2.1 is an improved and revised GSTARS 2.0 with graphical user interface. The unique features of all GSTARS models are the conjunctive use of the stream tube concept and of the minimum stream power theory. The application of minimum stream power theory allows the determination of optimum channel geometry with variable channel width and cross-sectional shape. The use of the stream tube concept enables the simulation of river hydraulics using one-dimensional numerical solutions to obtain a semi-two- dimensional presentation of the hydraulic conditions along and across an alluvial channel. According to the stream tube concept, no water or sediment particles can cross the walls of stream tubes, which is valid for many natural rivers. At and near sharp bends, however, sediment particles may cross the boundaries of stream tubes. GSTARS3, based on FORTRAN 90/95, addresses this phenomenon and further expands the capabilities of GSTARS 2.1 for cohesive and non-cohesive sediment transport in rivers and reservoirs. This paper presents the concepts, methods, and techniques used to develop the GSTARS series of computer models, especially GSTARS3. ?? 2008 International Research and Training Centre on Erosion and Sedimentation and the World Association for Sedimentation and Erosion Research.

  4. Understanding physical developer (PD): Part I--Is PD targeting lipids?

    PubMed

    de la Hunty, Mackenzie; Moret, Sébastien; Chadwick, Scott; Lennard, Chris; Spindler, Xanthe; Roux, Claude

    2015-12-01

    Physical developer (PD) is a fingermark development technique that involves the selective reduction of silver onto fingermark residue. PD can develop marks on porous substrates even if they have been wet, leading to the logical, long held belief that the reagent targets the water insoluble constituents in the fingermark residue. The present research has tested this hypothesis as part of a broader study that aims to identify the targets of physical developer. Spot tests of some fatty acids, cholesterol and squalene, treated with PD, showed that only cholesterol produced significant silver deposition. PD is known to be particularly effective on aged marks, however cholesterol degrades over time. These observations indicate that PD reactivity with fingermarks cannot solely be due to the presence of cholesterol. Fingermarks were deposited on paper and washed with various organic solvents before being treated with PD. PD effectiveness was intermittent on both solvent washed and unwashed sides of both natural and groomed marks; however, it was seen to effectively develop groomed samples that had been exposed to common lipid extraction solvents, shown to have removed the lipids by visualisation using the lipid stain Nile red. PD effectiveness was most affected by exposure of samples to solvents that could dissolve water soluble components, showing that the removal of these constituents (by either water, or other solvents) decreases the amount of silver deposited on the fingermark residue by the working solution. Close observation of PD developed samples showed variation in silver deposition uniformity when comparing a developed ridge to a pore site located on that ridge. Some samples showed an absence of silver, and other showed an increase of silver at pore locations. This indicates that the material excreted by the pores on the finger has an effect on silver deposition, suggesting that PD may be specifically targeting eccrine constituents that are present along the

  5. Development of neuroendocrine components of the thyroid axis in the direct-developing frog Eleutherodactylus coqui: formation of the median eminence and onset of pituitary TSH production.

    PubMed

    Jennings, David H; Evans, Bryce; Hanken, James

    2015-04-01

    Direct-developing frogs lack, wholly or in part, a wide range of larval features found in metamorphosing species and form adult-specific features precociously, during embryogenesis. Most information on thyroid regulation of direct development relies on hormone manipulations; the ontogeny of many thyroid axis components has not been fully described. This analysis examines differentiation of the median eminence of the hypothalamus and production of thyroid-stimulating hormone (TSH) by the pituitary of the direct-developing frog Eleutherodactylus coqui. The median eminence is established two-thirds of the way through embryogenesis. Cells immunoreactive to human TSHβ antibodies are first detected during embryogenesis and quantitative changes in TSHβ-IR cells resemble those in metamorphosing amphibians. Formation of the median eminence of the hypothalamus and TSHβ production by the pituitary precede or coincide with morphological changes during embryogenesis that occur during metamorphosis in biphasic anurans. Thus, while the onset of neuroendocrine regulation has changed during the evolution of direct development, it is likely that these thyroid axis components still mediate the formation of adult features.

  6. Through the Lens of Teacher Professional Development Components: The "Dialogic Video Cycle" as an Innovative Program to Foster Classroom Dialogue

    ERIC Educational Resources Information Center

    Gröschner, Alexander; Seidel, Tina; Kiemer, Katharina; Pehmer, Ann-Kathrin

    2015-01-01

    For developing professional development (PD) programs, research suggests referring to effective components. In developing a PD program on classroom dialogue, we explored to what extent effective components could be addressed. We conducted a study with two groups. In the "Dialogic Video Cycle" (DVC), six German teachers participated in a…

  7. Data-Mining Toolset Developed for Determining Turbine Engine Part Life Consumption

    NASA Technical Reports Server (NTRS)

    Litt, Jonathan S.

    2003-01-01

    The current practice in aerospace turbine engine maintenance is to remove components defined as life-limited parts after a fixed time, on the basis of a predetermined number of flight cycles. Under this schedule-based maintenance practice, the worst-case usage scenario is used to determine the usable life of the component. As shown, this practice often requires removing a part before its useful life is fully consumed, thus leading to higher maintenance cost. To address this issue, the NASA Glenn Research Center, in a collaborative effort with Pratt & Whitney, has developed a generic modular toolset that uses data-mining technology to parameterize life usage models for maintenance purposes. The toolset enables a "condition-based" maintenance approach, where parts are removed on the basis of the cumulative history of the severity of operation they have experienced. The toolset uses data-mining technology to tune life-consumption models on the basis of operating and maintenance histories. The flight operating conditions, represented by measured variables within the engine, are correlated with repair records for the engines, generating a relationship between the operating condition of the part and its service life. As shown, with the condition-based maintenance approach, the lifelimited part is in service until its usable life is fully consumed. This approach will lower maintenance costs while maintaining the safety of the propulsion system. The toolset is a modular program that is easily customizable by users. First, appropriate parametric damage accumulation models, which will be functions of engine variables, must be defined. The tool then optimizes the models to match the historical data by computing an effective-cycle metric that reduces the unexplained variability in component life due to each damage mode by accounting for the variability in operational severity. The damage increment due to operating conditions experienced during each flight is used to compute

  8. Models and Frameworks: A Synergistic Association for Developing Component-Based Applications

    PubMed Central

    Sánchez-Ledesma, Francisco; Sánchez, Pedro; Pastor, Juan A.; Álvarez, Bárbara

    2014-01-01

    The use of frameworks and components has been shown to be effective in improving software productivity and quality. However, the results in terms of reuse and standardization show a dearth of portability either of designs or of component-based implementations. This paper, which is based on the model driven software development paradigm, presents an approach that separates the description of component-based applications from their possible implementations for different platforms. This separation is supported by automatic integration of the code obtained from the input models into frameworks implemented using object-oriented technology. Thus, the approach combines the benefits of modeling applications from a higher level of abstraction than objects, with the higher levels of code reuse provided by frameworks. In order to illustrate the benefits of the proposed approach, two representative case studies that use both an existing framework and an ad hoc framework, are described. Finally, our approach is compared with other alternatives in terms of the cost of software development. PMID:25147858

  9. Development of multi-component explosive lenses for arbitrary phase velocity generation

    NASA Astrophysics Data System (ADS)

    Loiseau, Jason; Huneault, Justin; Petel, Oren; Goroshin, Sam; Frost, David; Higgins, Andrew; Zhang, Fan

    2013-06-01

    The combination of explosives with different detonation velocities and lens-like geometric shaping is a well-established technique for producing structured detonation waves. This technique can be extended to produce nearly arbitrary detonation phase velocities for the purposes of sequentially imploding pressurized tubes or driving Mach disks through high-density metalized explosives. The current study presents the experimental development of accelerating, multi-component lenses designed using simple geometric optics and idealized front curvature. The fast explosive component is either Composition C4 (VOD = 8 km/s) or Primasheet 1000 (VOD = 7 km/s), while the slow component varies from heavily amine-diluted nitromethane (amine mass fraction exceeding 20%) to packed metal and glass particle beds wetted with amine-sensitized nitromethane. The applicability of the geometric optic analog to such highly heterogeneous explosives is also investigated. The multi-layered lens technique is further developed as a means of generating a directed mass and momentum flux of metal particles via Mach-disk formation and jetting in circular and oval planar lenses.

  10. Regulation of molecular components of the synapse in the developing and adult rat superior cervical ganglion

    SciTech Connect

    Wu, K.; Black, I.B.

    1987-12-01

    Rat superior cervical sympathetic ganglion was used to begin studying the regulation of molecular components of the synapse. Ganglionic postsynaptic densities (PSDs) exhibited a thin, disc-shaped profile electron microscopically, comparable to that described for brain. Moreover, the presumptive ganglionic PSD protein (PSDp) was phosphorylated in the presence of Ca/sup 2 +/ and calmodulin, bound /sup 125/I-labeled calmodulin, and exhibited a M/sub r/ of 51,000 all characteristic of the major PSD protein of brain. These initial studies indicated that ganglionic PSDp and the major PSD protein of brain are comparable, allowing the study synaptic regulation in the well-defined superior cervical sympathetic ganglion. To obtain enough quantities of ganglionic PSDp, the authors used synaptic membrane fractions. During postnatal development, calmodulin binding to the ganglionic PSDp increased 411-fold per ganglion from birth to 60 days, whereas synaptic membrane protein increased only 4.5-fold. Consequently, different synaptic components apparently develop differently. Moreover, denervation of the superior cervical sympathetic ganglion in adult rats caused an 85% decrease in ganglionic PSDp-calmodulin binding, but denervation caused no change in synaptic membrane protein 2 weeks postoperatively. The observations suggest that presynaptic innervation selectively regulates specific molecular components of the postsynaptic membrane structure.

  11. Development of Novel Pre-alloyed PM Steels for Optimization of Machinability and Fatigue Resistance of PM Components

    NASA Astrophysics Data System (ADS)

    Mardan, Milad; Blais, Carl

    2016-03-01

    It is well known that a large proportion of ferrous PM components require secondary machining operations for dimensional conformance or for producing geometrical features that cannot be generated during die compaction. Nevertheless, the machining behavior of PM parts is generally characterized as being "difficult" due to the presence of residual porosity that lowers thermal conductivity and induces interrupted cutting. Several admixed additives such as MnS and BN-h can be used to improve the machining behavior of PM steels. Nevertheless, their negative effect on mechanical properties, especially fatigue resistance, makes their utilization uninteresting for the fabrication of high-performance PM steel components. This article summarizes the work carried out to develop a novel PM steel that was especially engineered to form machinability enhancing precipitates. This new material is pre-alloyed with tin (Sn) in order to form Cu-Sn (Cu(α)) precipitates during transient liquid phase sintering. The newly developed material presents machinability improvement of 165% compared to reference material used in the PM industry as well as increases in toughness and fatigue resistance of 100% and 13%, respectively.

  12. Development of the six-component rotating shaft balances for counter rotating open rotor testing

    NASA Astrophysics Data System (ADS)

    Bogdanov, V. V.; Lytov, V. V.; Manvelyan, V. S.

    2016-10-01

    Measurement of total aerodynamic loads acting on airplane's high speed CRORs, is one of the tasks of experimental aerodynamics. A special plant for this task solving was developed in TsAGI. One of the main challenges in the way of solving this problem is to develop a six-component rotating shaft balance (RSB) for the front and rear airscrews of CROR. The substantial stage of the balance development is the choice of the design. A promising design for the RSB was developed. It is a system of 12 non-prismatic beams, which is transmitting loads from the airscrews throughout a rim to a support. The rim connected to an airscrews hub and support rigidly connected to the shaft of VVP. Calculations have shown that this design has several advantages compared to known designs of eight beams.

  13. Understanding stakeholder participation in research as part of sustainable development.

    PubMed

    Bell, Simon; Morse, Stephen; Shah, Rupesh A

    2012-06-30

    Participation is often presented as a 'good' thing and a fairer way to represent views and opinions outside narrow confines of interest and expertise. However, the roots of participatory approaches within research contexts are deep and numerous twists and turns demonstrate a confused and possibly confusing morphology with significant gaps and weaknesses. In this paper 'via the medium' of the POINT (Policy Influence of Indicators) research project we trace elements of the recent history of group participation in sustainable development and the emergence of focus on four areas, most significantly how participatory methods are used. In the absence of strong evidence to contrary we suggest that the issue of how participants engage in participation remains a significant weakness for the field. In order to counter the apparent gap we suggest that a certain degree of structure and process can provide the oeuvre of participatory approaches with a higher degree of transparency in the research process and, by focus on the use of a method called Triple Task, group participatory events can be encouraged to yield greater insights into the workings of groups of all kinds.

  14. Flow simulation of the Component Development Integration Facility magnetohydrodynamic power train system

    SciTech Connect

    Chang, S.L.; Lottes, S.A.; Bouillard, J.X.; Petrick, M.

    1997-11-01

    This report covers application of Argonne National Laboratory`s (ANL`s) computer codes to simulation and analysis of components of the magnetohydrodynamic (MHD) power train system at the Component Development and Integration Facility (CDIF). Major components of the system include a 50-MWt coal-fired, two-stage combustor and an MHD channel. The combustor, designed and built by TRW, includes a deswirl section between the first and the second-stage combustor and a converging nozzle following the second-stage combustor, which connects to the MHD channel. ANL used computer codes to simulate and analyze flow characteristics in various components of the MHD system. The first-stage swirl combustor was deemed a mature technology and, therefore, was not included in the computer simulation. Several versions of the ICOMFLO computer code were used for the deswirl section and second-stage combustor. The MGMHD code, upgraded with a slag current leakage submodel, was used for the MHD channel. Whenever possible data from the test facilities were used to aid in calibrating parameters in the computer code, to validate the computer code, or to set base-case operating conditions for computations with the computer code. Extensive sensitivity and parametric studies were done on cold-flow mixing in the second-stage combustor, reacting flow in the second-stage combustor and converging nozzle, and particle-laden flow in the deswirl zone of the first-stage combustor, the second-stage combustor, and the converging nozzle. These simulations with subsequent analysis were able to show clearly in flow patterns and various computable measures of performance a number of sensitive and problematical areas in the design of the power train. The simulations of upstream components also provided inlet parameter profiles for simulation of the MHD power generating channel. 86 figs., 18 tabs.

  15. Effects of Er:YAG laser irradiation and manipulation treatments on dentin components, part 1: Fourier transform-Raman study

    NASA Astrophysics Data System (ADS)

    Soares, Luís Eduardo Silva; Do Espírito Santo, Ana Maria; Junior, Aldo Brugnera; Zanin, Fátima Antônia Aparecida; da Silva Carvalho, Carolina; de Oliveira, Rodrigo; Martin, Airton Abraha~O.

    2009-03-01

    The effects of laser etching, decontamination, and storage treatments on dentin components were studied using Fourier transform (FT)-Raman spectroscopy. Thirty bovine incisors were prepared to expose the dentin surface and then divided in two main groups based upon the decontamination process and storage procedure: autoclaved (group A, n=15) or stored in thymol aqueous solution (group B, n=15). The surfaces of the dentin slices were schematically divided into four areas, with each one corresponding to a treatment subgroup. The specimens were either etched with phosphoric acid (control subgroup) or irradiated with erbium-doped yttrium-aluminum-garnet (Er:YAG) laser (subgroups: I-80 mJ, II-120 mJ, and III-180 mJ, and total energy of 12 J). Samples were analyzed by FT-Raman spectroscopy; we collected three spectra for each area (before and after treatment). The integrated areas of five Raman peaks were calculated to yield average spectra. The areas of the peaks associated with phosphate content (P<0.001), type I collagen, and organic C-H bonds (P<0.05) were reduced significantly in group A (control). Analyses of samples irradiated with reduced laser energies did not show significant changes in the dentin components. These results suggest that thymol storage treatment is advised for in vitro study; furthermore, 12 J of Er:YAG laser energy does not affect dentin components.

  16. 10 CFR Appendix E to Part 110 - Illustrative List of Chemical Exchange or Ion Exchange Enrichment Plant Equipment and Components...

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... between the isotopes of uranium causes small changes in chemical reaction equilibria that can be used as a... 10 Energy 2 2013-01-01 2013-01-01 false Illustrative List of Chemical Exchange or Ion Exchange.... 110, App. E Appendix E to Part 110—Illustrative List of Chemical Exchange or Ion Exchange...

  17. 10 CFR Appendix E to Part 110 - Illustrative List of Chemical Exchange or Ion Exchange Enrichment Plant Equipment and Components...

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... between the isotopes of uranium causes small changes in chemical reaction equilibria that can be used as a... 10 Energy 2 2011-01-01 2011-01-01 false Illustrative List of Chemical Exchange or Ion Exchange.... 110, App. E Appendix E to Part 110—Illustrative List of Chemical Exchange or Ion Exchange...

  18. 10 CFR Appendix E to Part 110 - Illustrative List of Chemical Exchange or Ion Exchange Enrichment Plant Equipment and Components...

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... between the isotopes of uranium causes small changes in chemical reaction equilibria that can be used as a... 10 Energy 2 2014-01-01 2014-01-01 false Illustrative List of Chemical Exchange or Ion Exchange.... 110, App. E Appendix E to Part 110—Illustrative List of Chemical Exchange or Ion Exchange...

  19. 10 CFR Appendix E to Part 110 - Illustrative List of Chemical Exchange or Ion Exchange Enrichment Plant Equipment and Components...

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... between the isotopes of uranium causes small changes in chemical reaction equilibria that can be used as a... 10 Energy 2 2012-01-01 2012-01-01 false Illustrative List of Chemical Exchange or Ion Exchange.... 110, App. E Appendix E to Part 110—Illustrative List of Chemical Exchange or Ion Exchange...

  20. Methodology Development for Passive Component Reliability Modeling in a Multi-Physics Simulation Environment

    SciTech Connect

    Aldemir, Tunc; Denning, Richard; Catalyurek, Umit; Unwin, Stephen

    2015-01-23

    Reduction in safety margin can be expected as passive structures and components undergo degradation with time. Limitations in the traditional probabilistic risk assessment (PRA) methodology constrain its value as an effective tool to address the impact of aging effects on risk and for quantifying the impact of aging management strategies in maintaining safety margins. A methodology has been developed to address multiple aging mechanisms involving large numbers of components (with possibly statistically dependent failures) within the PRA framework in a computationally feasible manner when the sequencing of events is conditioned on the physical conditions predicted in a simulation environment, such as the New Generation System Code (NGSC) concept. Both epistemic and aleatory uncertainties can be accounted for within the same phenomenological framework and maintenance can be accounted for in a coherent fashion. The framework accommodates the prospective impacts of various intervention strategies such as testing, maintenance, and refurbishment. The methodology is illustrated with several examples.

  1. Developing Your Evaluation Plans: A Critical Component of Public Health Program Infrastructure.

    PubMed

    Lavinghouze, S Rene; Snyder, Kimberly

    A program's infrastructure is often cited as critical to public health success. The Component Model of Infrastructure (CMI) identifies evaluation as essential under the core component of engaged data. An evaluation plan is a written document that describes how to monitor and evaluate a program, as well as how to use evaluation results for program improvement and decision making. The evaluation plan clarifies how to describe what the program did, how it worked, and why outcomes matter. We use the Centers for Disease Control and Prevention's (CDC) "Framework for Program Evaluation in Public Health" as a guide for developing an evaluation plan. Just as using a roadmap facilitates progress on a long journey, a well-written evaluation plan can clarify the direction your evaluation takes and facilitate achievement of the evaluation's objectives.

  2. Psychoanalytic training experience and postgraduate professional development - Part II.

    PubMed

    Schneider, Jorge; Wilkerson, Douglas; Solomon, Brenda; Perlman, Caryle; Duval, Denise; Shelby, Dennis; Witten, Molly

    2017-03-02

    This exploratory study looks at the training and postgraduate experience of the 2008-2014 graduates of the Chicago Institute for Psychoanalysis. It follows our former study of all living graduates through the year 2007 (Schneider et al., 2014). The survey developed and used in the first study, with a few additional questions added to increase our understanding of the training experience, was sent to 38 graduates with a return rate of 58%. As with the first survey, graduates were invited to assess, among other training experiences, their training analysis, classroom work, and supervision, and to tell of their post-graduation involvement in teaching, supervising, study groups and other professional endeavors. They were also asked to rate their satisfaction with themselves as psychoanalysts and with their analytic career. The questions added to the previous survey related to the graduates' theoretical orientation, the influence on their training experiences of the change in gender distribution, and of the diversity of professions now represented in the analytic training program. They were also encouraged to provide spontaneous narrative data. The data from our second survey showed important differences when compared with our first. In the first survey male respondents were in the majority; in the second, women held the majority. Of the professions represented in the training program, psychiatry was the majority in the first survey, psychology and social work held the majority in the second. Most respondents claimed an object-relation theoretical orientation. Analytic immersion continues to decrease, with most respondents having two patients at the time of graduation and one at the time of the survey.

  3. Developing standard performance testing procedures for material control and accounting components at a site

    SciTech Connect

    Scherer, Carolynn P; Bushlya, Anatoly V; Efimenko, Vladimir F; Ilyanstev, Anatoly; Regoushevsky, Victor I

    2010-01-01

    The condition of a nuclear material control and accountability system (MC&A) and its individual components, as with any system combining technical elements and documentation, may be characterized through an aggregate of values for the various parameters that determine the system's ability to perform. The MC&A system's status may be functioning effectively, marginally or not functioning based on a summary of the values of the individual parameters. This work included a review of the following subsystems, MC&A and Detecting Material Losses, and their respective elements for the material control and accountability system: (a) Elements of the MC&A Subsystem - Information subsystem (Accountancy/Inventory), Measurement subsystem, Nuclear Material Access subsystem, including tamper-indicating device (TID) program, and Automated Information-gathering subsystem; (b) Elements for Detecting Nuclear Material Loses Subsystem - Inventory Differences, Shipper/receiver Differences, Confirmatory Measurements and differences with accounting data, and TID or Seal Violations. In order to detect the absence or loss of nuclear material there must be appropriate interactions among the elements and their respective subsystems from the list above. Additionally this work includes a review of regulatory requirements for the MC&A system component characteristics and criteria that support the evaluation of the performance of the listed components. The listed components had performance testing algorithms and procedures developed that took into consideration the regulatory criteria. The developed MC&A performance-testing procedures were the basis for a Guide for MC&A Performance Testing at the material balance areas (MBAs) of State Scientific Center of the Russian Federation - Institute for Physics and Power Engineering (SSC RF-IPPE).

  4. Program plan for research and development of HVDC power systems and components

    SciTech Connect

    Not Available

    1984-01-01

    The Division of Electric Energy Systems (EES) of the US Department of Energy (DOE) has formulated a program for research and development (R and D) of high-voltage direct-current (HVDC) power transmission and delivery systems and associated dc components. The program includes analysis of future utility system applications, development of new HVDC control and protection concepts, and advanced dc component research. The structure of this program will provide an appropriate balance between mid- and long-term options for the enhancement of HVDC power transmission and delivery for future electric power systems. This HVDC research program is intended to further develop and improve an important energy transport technology, one that will offer many opportunities to reduce future energy costs. The economics and operating constraints in alternating-current (ac) solutions strongly indicate that new HVDC technology options will be advantageous and will provide an enhanced ability to use generation and transmission system resources efficiently and economically in existing electric energy systems. Studies show that further development of this technology will lead to significant integration of new HVDC techniques into existing electric energy systems with appreciable economic and technical benefit. The R and D proposed in this HVDC Program Plan will be of substantial value to future electric power systems.

  5. Progress in Materials and Component Development for Advanced Lithium-ion Cells for NASA's Exploration Missions

    NASA Technical Reports Server (NTRS)

    Reid, Concha, M.; Reid, Concha M.

    2011-01-01

    Vehicles and stand-alone power systems that enable the next generation of human missions to the Moon will require energy storage systems that are safer, lighter, and more compact than current state-of-the- art (SOA) aerospace quality lithium-ion (Li-ion) batteries. NASA is developing advanced Li-ion cells to enable or enhance the power systems for the Altair Lunar Lander, Extravehicular Activities spacesuit, and rovers and portable utility pallets for Lunar Surface Systems. Advanced, high-performing materials are required to provide component-level performance that can offer the required gains at the integrated cell level. Although there is still a significant amount of work yet to be done, the present state of development activities has resulted in the synthesis of promising materials that approach the ultimate performance goals. This report on interim progress of the development efforts will elaborate on the challenges of the development activities, proposed strategies to overcome technical issues, and present performance of materials and cell components.

  6. Development of Continuous, Direct Feedback Control Systems for Sintering of Metallic Components

    SciTech Connect

    Diran Apelian; Marc M. Baum

    2006-09-18

    N,N.-Ethylenebisstearimide (EBS) is one of the most commonlyused lubricants in the powder metallurgy (PM) industry in the sintering process. During sintering, the lubricated powder compacts are heat-treated to temperatures in excess of 1,200 °C thus fusing adjacent particles and yielding a part with improved mechanical strength. Delubrication commonly is achieved in the first zone of a sintering furnace by heating the part to temperatures in the 500-600 °C temperature range at a fixed rate and under controlled atmospheric conditions; this strategy minimizes defects, carbon contamination, and compact deformation. The de-lubricated part then enters the second zone (commonly in the 1200-1300 °C temperature range) for sintering. The third zone cools the sintered part at a desired rate to obtain the requisite micro-structural properties. Controlled delubrication is imperative towards achieving high quality parts for the following reasons: the elevated thermal gradient at the transition between the first and second zones can cause parts to expand rapidly and develop microscopic fissures (.blistering.); improper gas flows and belt speeds can lead to carbon deposition on the part and at the grain boundaries (sooting); delubrication products deposit throughout the furnace, even in the coolers, which are far removed from the preheating chamber, leading to significant maintenance costs; pollutants emitted in the exhaust stream of furnaces operating inefficiently are increasingly of environmental concern. In practice, lubricant removal is difficult to control, which often leads to reduced yields in PM manufacturing processes. Throughput is another important issue: process control ideally should lead to a delubrication cycle that yields defect-free parts in a minimum of furnace time, thereby increasing productivity and reducing the net energy consumption. Efficient process control requires rapid monitoring of suitable indicators, preferably gasphase products of delubrication

  7. Chemical Kinetics Mechanism Reduction Based on Principal Component Analysis: Development and Testing of Some New Implementations

    DTIC Science & Technology

    2013-05-01

    prediction of propulsion system performance. In addition, programs employed in this study for screening the merit of reduced mechanisms were...development of system -specific gas-phase finite-rate chemical kinetics mechanisms is a significant part of these efforts (Anderson et al., 2010; Chen and...employed to model other combustion systems . The final step involves producing a “reduced” (or skeletal) mechanism from the detailed/full one

  8. Development of Spray on Bag for manufacturing of large composites parts: Diffusivity analysis

    NASA Astrophysics Data System (ADS)

    Dempah, Maxime Joseph

    Bagging materials are utilized in many composites manufacturing processes. The selection is mainly driven by cost, temperature requirements, chemical compatibility and tear properties of the bag. The air barrier properties of the bag are assumed to be adequate or in many cases are not considered at all. However, the gas barrier property of a bag is the most critical parameter, as it can negatively affect the quality of the final laminate. The barrier property is a function of the bag material, uniformity, thickness and temperature. Improved barrier properties are needed for large parts, high pressure consolidated components and structures where air stays entrapped on the part surface. The air resistance property of the film is defined as permeability and is investigated in this thesis. A model was developed to evaluate the gas transport through the film and an experimental cell was implemented to characterize various commercial films. Understanding and characterizing the transport phenomena through the film allows optimization of the bagging material for various manufacturing processes. Spray-on-Bag is a scalable alternative bagging method compared to standard films. The approach allows in-situ fabrication of the bag on large and complex geometry structures where optimization of the bag properties can be varied on a local level. An experimental setup was developed and implemented using a six axis robot and an automated spraying system. Experiments were performed on a flat surface and specimens were characterized and compared to conventional films. Air barrier properties were within range of standard film approaches showing the potential to fabricate net shape bagging structures in an automated process.

  9. Development and extension of an aggregated scale model: Part 2 — Extensions to ASMITA

    NASA Astrophysics Data System (ADS)

    Townend, Ian; Wang, Zheng Bing; Stive, Marcel; Zhou, Zeng

    2016-10-01

    Whilst much attention has been given to models that describe wave, tide and sediment transport processes in sufficient detail to determine the local changes in bed level over a relatively detailed representation of the bathymetry, far less attention has been given to models that consider the problem at a much larger scale (e.g. that of geomorphological elements such as a tidal flat and tidal channel). Such aggregated or lumped models tend not to represent the processes in detail but rather capture the behaviour at the scale of interest. One such model developed using the concept of an equilibrium concentration is the Aggregated Scale Morphological Interaction between Tidal basin and Adjacent coast (ASMITA). In a companion paper (Part 1), we detail the original model and provide some new insights into the concepts of equilibrium, and horizontal and vertical exchange that are key components of this modelling approach. In this paper, we summarise a range of developments that have been undertaken to extend the original model concept, to illustrate the flexibility and power of the conceptual framework. However, adding detail progressively moves the model in the direction of the more detailed process-based models and we give some consideration to the boundary between the two.

  10. Advanced Materials and Component Development for Lithium-Ion Cells for NASA Missions

    NASA Technical Reports Server (NTRS)

    Reid, Concha M.

    2012-01-01

    Human missions to Near Earth Objects, such as asteroids, planets, moons, liberation points, and orbiting structures, will require safe, high specific energy, high energy density batteries to provide new or extended capabilities than are possible with today s state-of-the-art aerospace batteries. The Enabling Technology Development and Demonstration Program, High Efficiency Space Power Systems Project battery development effort at the National Aeronautics and Space Administration (NASA) is continuing advanced lithium-ion cell development efforts begun under the Exploration Technology Development Program Energy Storage Project. Advanced, high-performing materials are required to provide improved performance at the component-level that contributes to performance at the integrated cell level in order to meet the performance goals for NASA s High Energy and Ultra High Energy cells. NASA s overall approach to advanced cell development and interim progress on materials performance for the High Energy and Ultra High Energy cells after approximately 1 year of development has been summarized in a previous paper. This paper will provide an update on these materials through the completion of 2 years of development. The progress of materials development, remaining challenges, and an outlook for the future of these materials in near term cell products will be discussed.

  11. Advanced Materials and Component Development for Lithium-ion Cells for NASA Missions

    NASA Technical Reports Server (NTRS)

    Reid, Concha M.

    2012-01-01

    Human missions to Near Earth Objects, such as asteroids, planets, moons, libration points, and orbiting structures, will require safe, high specific energy, high energy density batteries to provide new or extended capabilities than are possible with today s state-of-the-art aerospace batteries. The National Aeronautics and Space Administration is developing advanced High Energy and Ultra High Energy lithium-ion cells to address these needs. In order to meet the performance goals, advanced, high-performing materials are required to provide improved performance at the component-level that contributes to performance at the integrated cell level. This paper will provide an update on the performance of experimental materials through the completion of two years of development. The progress of materials development, remaining challenges, and an outlook for the future of these materials in near term cell products will be discussed.

  12. Technology Professional Development and Instructional Technology Integration among Part-Time Faculty at Illinois Community Colleges

    ERIC Educational Resources Information Center

    Roohani, Behnam

    2014-01-01

    This study focused on exploring Illinois community college faculty development coordinators' perceptions about how they are implementing faculty technology professional development programs and providing technical support for part-time faculty in the Illinois community college systems. Also examined were part-time faculty perceptions of the degree…

  13. RNA-binding proteins in eye development and disease: implication of conserved RNA granule components.

    PubMed

    Dash, Soma; Siddam, Archana D; Barnum, Carrie E; Janga, Sarath Chandra; Lachke, Salil A

    2016-07-01

    The molecular biology of metazoan eye development is an area of intense investigation. These efforts have led to the surprising recognition that although insect and vertebrate eyes have dramatically different structures, the orthologs or family members of several conserved transcription and signaling regulators such as Pax6, Six3, Prox1, and Bmp4 are commonly required for their development. In contrast, our understanding of posttranscriptional regulation in eye development and disease, particularly regarding the function of RNA-binding proteins (RBPs), is limited. We examine the present knowledge of RBPs in eye development in the insect model Drosophila as well as several vertebrate models such as fish, frog, chicken, and mouse. Interestingly, of the 42 RBPs that have been investigated for their expression or function in vertebrate eye development, 24 (~60%) are recognized in eukaryotic cells as components of RNA granules such as processing bodies, stress granules, or other specialized ribonucleoprotein (RNP) complexes. We discuss the distinct developmental and cellular events that may necessitate potential RBP/RNA granule-associated RNA regulon models to facilitate posttranscriptional control of gene expression in eye morphogenesis. In support of these hypotheses, three RBPs and RNP/RNA granule components Tdrd7, Caprin2, and Stau2 are linked to ocular developmental defects such as congenital cataract, Peters anomaly, and microphthalmia in human patients or animal models. We conclude by discussing the utility of interdisciplinary approaches such as the bioinformatics tool iSyTE (integrated Systems Tool for Eye gene discovery) to prioritize RBPs for deriving posttranscriptional regulatory networks in eye development and disease. WIREs RNA 2016, 7:527-557. doi: 10.1002/wrna.1355 For further resources related to this article, please visit the WIREs website.

  14. An operational measure of physician lifelong learning: its development, components and preliminary psychometric data.

    PubMed

    Hojat, Mohammadreza; Nasca, Thomas J; Erdmann, James B; Frisby, Anthony J; Veloski, J Jon; Gonnella, Joseph S

    2003-07-01

    Despite the emphasis placed on physicians' lifelong learning, no psychometrically sound instrument has been developed to provide an operational measure of the concept and its components among physicians. The authors designed this study to develop a tool for measuring physician lifelong learning, to identify its underlying components and to assess its psychometric properties. A 37-item questionnaire was developed, based on a review of literature and the results of two pilot studies. Psychometric analyses of the responses of 160 physicians identified 19 items that were included in the Jefferson Scale of Physician Lifelong Learning. Factor analysis of the 19 items showed five meaningful factors that were consistent with the definition and major features of lifelong learning. They were 'need recognition', 'research endeavor', 'self-initiation', 'technical skills' and 'personal motivation'. The method of contrasted groups provided evidence in support of the validity of the five factors. The factors' reliability was assessed by coefficient alpha. It is concluded that lifelong learning is a multifaceted concept, and its operational measure is feasible for evaluating different educational programs and for studying group differences among physicians.

  15. Development of HVOF Sprayed Erosion/Oxidation Resistant Coatings for Composite Structural Components in Propulsion Systems

    NASA Technical Reports Server (NTRS)

    Knight, R.; Ivosevic, M.; Twardowski, T. E.; Kalidindi, S. R.; Sutter, James K.; Kim, D. Y.; Gray, Hugh R. (Technical Monitor)

    2002-01-01

    Thermally sprayed coatings are being studied and developed as methods of enabling lightweight composites to be used more extensively as structural components in propulsion applications in order to reduce costs and improve efficiency through weight reductions. The primary goal of this work is the development of functionally graded material [FGM] polymer/metal matrix composite coatings to provide improved erosion/oxidation resistance to polyimide-based polymer matrix composite [PMC] substrates. The goal is to grade the coating composition from pure polyimide, similar to the PMC substrate matrix on one side, to 100 % WC-Co on the other. Both step-wise and continuous gradation of the loading of the WC-Co reinforcing phase are being investigated. Details of the coating parameter development will be presented, specifically the high velocity oxy-fuel [HVOF] combustion spraying of pure PMR-11 matrix material and layers of various composition PMR-II/WC-Co blends onto steel and PMR-15 composite substrates. Results of the HVOF process optimization, microstructural characterization, and analysis will be presented. The sprayed coatings were evaluated using standard metallographic techniques - optical and scanning electron microscopy [SEM]. An SEM + electron dispersive spectroscopy [EDS] technique has also been used to confirm retention of the PMR-II component. Results of peel/butt adhesion testing to determine adhesion will also be presented.

  16. Development of HVOF Sprayed Erosion/Oxidation Resistant Coatings for Composite Structural Components in Propulsion Systems

    NASA Technical Reports Server (NTRS)

    Ivosevic, M.; Twardowski, T.; Kalidindi, S.; Knight, R.; Sutter, J.; Kim, D. Y.

    1990-01-01

    Thermally sprayed coatings are being studied and developed as methods of enabling lightweight composites to be used more extensively as structural components in propulsion applications in order to reduce costs and improve efficiency through weight reductions. The primary goal of this work is the development of functionally graded material [FGM] polymer/metal matrix composite coatings to provide improved erosion/oxidation resistance to polyimide-based polymer matrix composite [PMC] substrates. The goal is to grade the coating composition from pure polyimide, similar to the PMC substrate matrix on one side, to 100% WC-Co on the other. Both step-wise and continuous gradation of the loading of the WC-Co reinforcing phase are being investigated, Details of the coating parameter development will be presented, specifically the high velocity oxy-fuel [HVOF] combustion spraying of pure PMR-I1 matrix material and layers of various composition PMR-II/WC-Co blends onto steel and PMR-15 composite substrates. Results of the HVOF process optimization, microstructural characterization, and analysis will be presented. The sprayed coatings were evaluated using standard metallographic techniques - optical and scanning electron microscopy [SEMI. An SEM + electron dispersive spectroscopy [EDS] technique has also been used to confirm retention of the PMR-I1 component. Results of peel/butt adhesion testing to determine adhesion will also be presented.

  17. Development of Advanced In-Cylinder Components and Tribological Systems for Low Heat Rejection Diesel Engines

    NASA Technical Reports Server (NTRS)

    Yonushonis, T. M.; Wiczynski, P. D.; Myers, M. R.; Anderson, D. D.; McDonald, A. C.; Weber, H. G.; Richardson, D. E.; Stafford, R. J.; Naylor, M. G.

    1999-01-01

    In-cylinder components and tribological system concepts were designed, fabricated and tested at conditions anticipated for a 55% thermal efficiency heavy duty diesel engine for the year 2000 and beyond. A Cummins L10 single cylinder research engine was used to evaluate a spherical joint piston and connecting rod with 19.3 MPa (2800 psi) peak cylinder pressure capability, a thermal fatigue resistant insulated cylinder head, radial combustion seal cylinder liners, a highly compliant steel top compression ring, a variable geometry turbocharger, and a microwave heated particulate trap. Components successfully demonstrated in the final test included spherical joint connecting rod with a fiber reinforced piston, high conformability steel top rings with wear resistant coatings, ceramic exhaust ports with strategic oil cooling and radial combustion seal cylinder liner with cooling jacket transfer fins. A Cummins 6B diesel was used to develop the analytical methods, materials, manufacturing technology and engine components for lighter weight diesel engines without sacrificing performance or durability. A 6B diesel engine was built and tested to calibrate analytical models for the aluminum cylinder head and aluminum block.

  18. Program for the development of high temperature electrical materials and components

    NASA Technical Reports Server (NTRS)

    Neff, W. S.; Lowry, L. R.

    1972-01-01

    Evaluation of high temperature, space-vacuum performance of selected electrical materials and components, high temperature capacitor development, and evaluation, construction, and endurance testing of compression sealed pyrolytic boron nitride slot insulation are described. The first subject above covered the aging evaluation of electrical devices constructed from selected electrical materials. Individual materials performances were also evaluated and reported. The second subject included study of methods of improving electrical performance of pyrolytic boron nitride capacitors. The third portion was conducted to evaluate the thermal and electrical performance of pyrolytic boron nitride as stator slot liner material under varied temperature and compressive loading. Conclusions and recommendations are presented.

  19. ANL`s research and development of alternative components for MCFC`s

    SciTech Connect

    Kucera, G.H.; Brown, A.P.; Roche, M.; Chu, D.; Indacochea, E.

    1992-09-01

    Molten carbonate fuel cell (MCFC) systems are currently limited by several technical problems. The objectives of this project are to focus on these problems and develop materials . and cell components that will ameliorate or eliminate them. Specifically, new ceramic materials are being investigated for dimensionally stable electrode materials with improved chemical and electrochemical properties over the present NiO cathode and Ni/Cr and Ni/Al anodes. Also, altemative electrolyte formulations to the present Li{sub 2}CO{sub 3}-K{sub 2}CO{sub 3} are being studied.

  20. Development and study of aluminum-air electrochemical generator and its main components

    NASA Astrophysics Data System (ADS)

    Ilyukhina, A. V.; Kleymenov, B. V.; Zhuk, A. Z.

    2017-02-01

    Aluminum-air power sources are receiving increased attention for applications in portable electronic devices, transportation, and energy systems. This study reports on the development of an aluminum-air electrochemical generator (AA ECG) and provides a technical foundation for the selection of its components, i.e., aluminum anode, gas diffusion cathode, and alkaline electrolyte. A prototype 1.5 kW AA ECG with specific energy of 270 Wh kg-1 is built and tested. The results of this study demonstrate the feasibility of AA ECGs as portable reserve and emergency power sources, as well as power sources for electric vehicles.

  1. Development of improved and corrosion-resistant surfaces for fossil power system components

    SciTech Connect

    Sikka, V.K.; Santella, M.L.; Goodwin, G.M.

    1996-06-01

    The purpose of this task is to develop the corrosion-resistant surfaces on a variety of fossil power system components. The Fe-Al alloys ranging in aluminum from 16 to 36 @ % are of interest. The surfaces of Fe-Al alloys can be produced by weld overlay. However, because of their limited room-temperature ductility, the production of weld wire for these compositions is not commercially feasible. The alloying element dilution during weld overlay also makes depositing exact surface composition rather difficult.

  2. 5 CFR Appendix B to Part 2641 - Agency Components for Purposes of 18 U.S.C. 207(c)

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... listed as Minority Business Development Administration). National Institute of Standards and Technology... Administration). Food and Drug Administration. Health Resources and Services Administration (effective May...

  3. Development of equipment parameter tolerances for the ultrasonic inspection of steel components: Application to components up to 3 inches thick

    SciTech Connect

    Green, E.R.; Doctor, S.R.; Hockey, R.L.; Diaz, A.A. )

    1992-06-01

    This report documents work performed at Pacific Northwest Laboratory on the effect of frequency domain equipment interactions on the reliability of ultrasonic inservice inspection. The primary focus of this work is to provide information to the United States Nuclear Regulatory Commission on the acceptability of equipment parameter tolerances as given in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section 11 Appendix 8. Mathematical models were developed for the entire ultrasonic inspection system including sound propagation through the inspection sample. The models were used to determine worst-case inspection scenarios for thin sections (piping), and these worst-case inspection scenarios were then used in sensitivity studies to determine the suitability of equipment parameter tolerances. Ultrasonics literature was reviewed to find worst-case inspection scenarios outside the scope of the model used, but none that were significantly worse were found. Experiments were performed to confirm the important modeling results. Methods for reducing parameter sensitivity such as the use of a phase insensitive receive were also investigated. The model predicted that ASME Code tolerances for equipment bandwidth are acceptable, but tolerances for center frequency are too broad to provide reliable inspection of worst-case defects using narrow band systems. Experiments confirmed the basic trends predicted by the model, but the model seems to be conservative in that it shows greater sensitivity than is found empirically.

  4. The Connective Tissue Components of Optic Nerve Head Cupping in Monkey Experimental Glaucoma Part 1: Global Change

    PubMed Central

    Yang, Hongli; Ren, Ruojin; Lockwood, Howard; Williams, Galen; Libertiaux, Vincent; Downs, Crawford; Gardiner, Stuart K.; Burgoyne, Claude F.

    2015-01-01

    Purpose To characterize optic nerve head (ONH) connective tissue change within 21 monkey experimental glaucoma (EG) eyes, so as to identify its principal components. Methods Animals were imaged three to five times at baseline then every 2 weeks following chronic unilateral IOP elevation, and euthanized early through end-stage confocal scanning laser tomographic change. Optic nerve heads were serial-sectioned, three-dimensionally (3D) reconstructed, delineated, and quantified. Overall EG versus control eye differences were assessed by general estimating equations (GEE). Significant, animal-specific, EG eye change was required to exceed the maximum physiologic intereye differences in six healthy animals. Results Overall EG eye change was significant (P < 0.0026) and animal-specific EG eye change most frequent, for five phenomena (number of EG eyes and range of animal-specific change): posterior laminar deformation (21, −29 to −437 μm), laminar thickening (11, 20–73 μm) and thinning (3, −23 to −31 μm), scleral canal expansion (17, 20–139 μm), outward anterior (16, −16 to −124 μm) and posterior (17, −22 to −279 μm) laminar insertion migration, and peripapillary scleral bowing (11, 21–77 μm). Experimental glaucoma versus control eye laminar thickness differences were bimodal in behavior, being thickened in most EG eyes demonstrating the least deformation and less thickened or thinned in most EG eyes demonstrating the greatest deformation. Conclusions Our postmortem studies retrospectively identify five connective tissue components of ONH “cupping” in monkey EG which serve as targets for longitudinally staging and phenotyping ONH connective tissue alteration within all forms of monkey and human optic neuropathy. PMID:26641545

  5. Development of an animal-component free medium for vero cells culture.

    PubMed

    Rourou, Samia; van der Ark, Arno; van der Velden, Tiny; Kallel, Héla

    2009-01-01

    This work describes the development of an animal-component free medium (IPT-AFM) that allows an optimal growth of Vero cells, an adherent cell line used for the production of viral vaccines. Statistical experimental design was applied to identify crucial nutrients that affect cell growth. Using Medium 199 or MEM as a basal medium, a serum-free medium (SFM) referred as IPT-SFM that only enclosed transferrin as a component of animal origin was developed at first. Then, the composition of IPT-SFM was further improved to obtain an animal-component free medium named IPT-AFM. IPT-AFM contains M199 as a basal medium, plant hydrolysates, epidermal growth factor, ethanolamine, ferric citrate, and vitamin C. Among various plant hydrolysates, specific combinations of soy (Hypep 1510) and wheat gluten (Hypeps 4601 and 4605) hydrolysates, were identified to promote cell growth; whereas individual Hypeps had a minor positive effect on cell growth. Nevertheless, the removal of serum did influence cell attachment. Coating tissue-culture flasks with teleostean, a product extracted from cold water fish skin, had not only enhanced cell attachment but also improved cell growth performance in static cultures. Different non-animal proteases were also assessed as an alternative to trypsin. TrypLE Select, a recombinant trypsin, gave the best cell growth performances. Kinetics of cell growth in IPT-AFM were investigated in T-flasks, cell growth was comparable with that obtained in MEM+10% fetal calf serum (FCS). A mean cell division number equal to 2.26 +/- 0.18 and a specific growth rate micro 0.019 +/- 0.003 h(-1) were achieved in IPT-AFM.

  6. Development of system level integration of compact RF components on multilayer liquid crystal polymer (LCP)

    NASA Astrophysics Data System (ADS)

    Chung, David

    element antenna array, the concept of beam steering is shown. Using this antenna array as a building block, an 8 x 8 element antenna array is shown with the measured results when conformed around a cylinder. Further expanding the antenna array, a 16 x 16 element antenna array is designed, fabricated, and measured. All of these antenna arrays use LCP as a platform for lightweight and low cost satellite communication applications. Finally, using the integration technology and expertise developed from the previous work, a 60 GHz transceiver front end is designed on LCP for high speed wireless communication applications. Two dual mode filters and high-gain vertical dipoles are integrated at the packaging level on LCP to create a low cost system. A PA and LNA are included in the system to increase the system gain. The measurements of the dual mode filters are presented as well as the fully integrated transceiver pattern measurements and gain measurements of each of the transmitting and receiving mode. This research contributes to LCP integration technology with more compact and higher frequency multilayer applications while focusing on integration of the components at the system packaging level to achieve optimal compactness. The highlight of this work is in developing key technologies for multilayer integration on organic LCP such as HDI interconnects and RF MEMS; applying the technology to create reconfigurable RF components such as reconfigurable antennas and compact low voltage phase shifters; and integrating the components to create compact low cost multilayer RF front end systems.

  7. Rethinking blood components and patients: Patient blood management. Possible ways for development in France.

    PubMed

    Folléa, Gilles

    2016-01-01

    As any therapeutic means, blood transfusion requires regular evaluation, particularly for its indications, effectiveness and risks. A better awareness of the risks of blood transfusion, the availability of randomized clinical trials, the evolution of the quality of blood components, and the economic constraints shared by all countries, all have led to rethink both transfusion therapy as a whole and the organization of the transfusion chain from donor to recipient. In this context, patient blood management (PBM) appears as an evidence-based, patient centred, multidisciplinary approach, aiming to optimise the care of patients who might need transfusion and consequently the use of blood products. This paper presents updated scientific bases of PBM and the three pillars founding it. As PBM is developing fast in other European countries, this review proposes ways to explore for its development in France. It finally proposes to integrate PBM in a wider and coordinated approach of the blood supply management, with tools to improve the effectiveness and efficiency of the transfusion chain, starting with the needs of the patients and ending with an optimum treatment of the patient, including the appropriate number of blood components of the required quality. A better understanding, implementation and assessment of this coordinated global approach, allowing to adapt donor collections to the patients' needs in compliance with safety requirements for patients and donors, in a coordinated way, will certainly be a major challenge for transfusion medicine in the near future, for the benefit of patients, donors and all other stakeholders involved in the transfusion chain.

  8. Development of wear resistant ceramic coatings for diesel engine components. Final report

    SciTech Connect

    Haselkorn, M.H.

    1992-04-01

    Improved fuel economy and a reduction of emissions can be achieved by insulation of the combustion chamber components to reduce heat rejection. However, insulating the combustion chamber components will also increase the operating temperature of the piston ring/cylinder liner interface from approximately 150{degree}C to over 300{degree}C. Existing ring/liner materials can not withstand these higher operating temperatures and for this reason, new materials need to be developed for this critical tribological interface. The overall goal of this program is the development of piston ring/cylinder liner material pairs which would be able to provide the required friction and wear properties at these more severe operating conditions. More specifically, this program first selected, and then evaluated, potential d/wear resistant coatings which could be applied to either piston rings an or cylinder liners and provide, at 350{degree}C under lubricated conditions, coefficients of friction below 0.1 and wear rates of less than 25 {times} lO{sup {minus}6} mm/hour. The processes selected for applying the candidate wear resistant coatings to piston rings and/or cylinder liners were plasma spraying, chemical vapor, physical vapor and low temperature arc vapor deposition techniques as well as enameling techniques.

  9. Development of Certain Protein Kinase Inhibitors with the Components from Traditional Chinese Medicine

    PubMed Central

    Liu, Minghua; Zhao, Ge; Cao, Shousong; Zhang, Yangyang; Li, Xiaofang; Lin, Xiukun

    2017-01-01

    Traditional Chinese medicines (TCMs) have been used in China for more than two thousand years, and some of them have been confirmed to be effective in cancer treatment. Protein kinases play critical roles in control of cell growth, proliferation, migration, survival, and angiogenesis and mediate their biological effects through their catalytic activity. In recent years, numerous protein kinase inhibitors have been developed and are being used clinically. Anticancer TCMs represent a large class of bioactive substances, and some of them display anticancer activity via inhibiting protein kinases to affect the phosphoinositide 3-kinase, serine/threonine-specific protein kinases, pechanistic target of rapamycin (PI3K/AKT/mTOR), P38, mitogen-activated protein kinase (MAPK) and extracellular signal-regulated kinases (ERK) pathways. In the present article, we comprehensively reviewed several components isolated from anticancer TCMs that exhibited significantly inhibitory activity toward a range of protein kinases. These components, which belong to diverse structural classes, are reviewed herein, based upon the kinases that they inhibit. The prospects and problems in development of the anticancer TCMs are also discussed. PMID:28119606

  10. Advanced Diesel Engine Component Development Program, final report - tasks 4-14

    SciTech Connect

    Kaushal, T.S.; Weber, K.E.

    1994-11-01

    The Advanced Diesel Engine Component Development (ADECD) Program is a multi-year, multi-phase effort to develop and demonstrate the critical technology needed to advance the heavy-duty low heat rejection (LHR) engine concept for the long-haul, heavy-duty truck market. The ADECD Program has been partitioned into two phases. The first phase, Phase 1, was completed in 1986, resulting in definition of the Advanced Diesel Reference Engine (ADRE)III. The second phase, Phase 11/111, examines the feasibility of the ADRE concepts for application to the on-highway diesel engine. Phase 11/111 is currently underway. This project is sponsored by the U.S. Department of Energy, Office of Transportation Technologies. The work has been performed by the Detroit Diesel Corporation (DDC) under Contract DEN3-329 with the NASA Lewis Research Center, who provide project management and technical direction.

  11. Development of high power radio frequency components for fusion plasma heating. Final report, Revision 3

    SciTech Connect

    1997-09-11

    The purpose of this CRADA was to develop advanced microwave heating systems for both ion cyclotron heating and electron cyclotron heating for magnetic fusion reactors. This involved low-frequency (UHF), high-power (millimeter-wave) microwave components, such as antennas, windows, and matching elements. This CRADA also involved developing conceptual designs for new microwave sources. General Atomics built and tested the distributed cooled window and provided LLNL with transmission and reflection test data in order to then benchmark the EM computer codes. The combline antenna built and analyzed by LLNL was based on a GA design. GA provided LLNL with a number of niobium plates for hot pressing and provided the necessary guidance to allow successful bonding. GA representatives were on site at LLNL on numerous occasions to consult and give guidance on the ferroelectric tuner, combline antenna and distributed window analysis.

  12. Advanced manufacturing development of a composite empennage component for L-1011 aircraft

    NASA Technical Reports Server (NTRS)

    1978-01-01

    Work continued toward the development of tooling and processing concepts required for a cocured hat/skin cover assembly. A plan was developed and implemented to develop the process for using preimpregnated T300/5208 with a resin content of 34 + or - 2 percent by weight. Use of this material results in a simplified laminating process because removal by bleeding or prebleeding is no longer required. The approach to this task basically consists of fabricating and testing flat laminated panels and simulated structural panels to verify known processing techniques relative to end-laminate quality. The flat panels were used to determine air bleeding arrangement and required cure cycle. Single and multihat-stiffened panels were fabricated using the established air bleeding arrangement and cure cycle with the resulting cured parts yielding excellent correlation of ply thickness with all surfaces clear of porosity and voids.

  13. Unmanned Aerial Systems as Part of a Multi-Component Assessment Strategy to Address Climate Change and Atmospheric Processes

    NASA Astrophysics Data System (ADS)

    Lange, Manfred; Vrekoussis, Mihalis; Sciare, Jean; Argyrides, Marios; Ioannou, Stelios; Keleshis, Christos

    2015-04-01

    Unmanned Aerial Systems (UAS) have been established as versatile tools for different applications, providing data and observations for atmospheric and Earth-Systems research. They offer an urgently needed link between in-situ ground based measurements and satellite remote sensing observations and are distinguished by significant versatility, flexibility and moderate operational costs. UAS have the proven potential to contribute to a multi-component assessment strategy that combines remote-sensing, numerical modelling and surface measurements in order to elucidate important atmospheric processes. This includes physical and chemical transformations related to ongoing climate change as well as issues linked to aerosol-cloud interactions and air quality. The distinct advantages offered by UAS comprise, to name but a few: (i) their ability to operate from altitudes of a few meters to up to a few kilometers; (ii) their capability to perform autonomously controlled missions, which provides for repeat-measurements to be carried out at precisely defined locations; (iii) their relative ease of operation, which enables flexible employment at short-term notice and (iv) the employment of more than one platform in stacked formation, which allows for unique, quasi-3D-observations of atmospheric properties and processes. These advantages are brought to bear in combining in-situ ground based observations and numerical modeling with UAS-based remote sensing in elucidating specific research questions that require both horizontally and vertically resolved measurements at high spatial and temporal resolutions. Employing numerical atmospheric modelling, UAS can provide survey information over spatially and temporally localized, focused areas of evolving atmospheric phenomena, as they become identified by the numerical models. Conversely, UAS observations offer urgently needed data for model verification and provide boundary conditions for numerical models. In this presentation, we will

  14. Supporting the transition from weight loss to maintenance: development and optimisation of a face-to-face behavioural intervention component.

    PubMed

    Sainsbury, Kirby; Cleland, Claire L; Evans, Elizabeth H; Adamson, Ashley; Batterham, Alan; Dombrowski, Stephan U; Gellert, Paul; Hill, Moira; Kwasnicka, Dominika; Scott, Dawn; Sniehotta, Falko F; White, Martin; Araújo-Soares, Vera

    2017-01-01

    After weight loss, most individuals regain lost weight. Interventions to support the transition from successful loss to weight loss maintenance (WLM), regardless of the method of prior weight loss, are needed. The aims of this study were to (1) develop a face-to-face behavioural intervention session to support overweight and obese individuals who have recently lost a clinically significant amount of weight in the transition to WLM; (2) to assess the single-session intervention for acceptability and feasibility prior to its use in a larger, 12-month, multi-component trial; and (3) to optimise the intervention session for future use based on participant feedback. Participants with a Body Mass Index of ≥25 kg/m(2) prior to a ≥5% weight loss in the previous 12 months were recruited via the local government authority and community-based advertisements. Each attended the one-hour session with a trained facilitator, which focused on setting maintenance-relevant weight, eating, and physical activity goals. Semi-structured interviews were carried out immediately post-session to obtain feedback on the acceptability of this intervention component. Data were used to generate recommendations for changes to the session, which were discussed by the team, and used to optimise the session. Seventeen participants (13 female; median WL = 13%) were recruited. All participants evaluated the intervention session positively; 11 participants suggested improvements including reducing information provision in favour of greater focus on identifying and coping with barriers, and the inclusion of practical examples. The systematic refinement and optimisation process resulted in an acceptable and feasible face-to-face behavioural intervention session (described here), which will be tested as part of a multi-component intervention. We anticipate the session could be used to supplement existing support including online services, and has the potential to benefit people who have lost a

  15. Supporting the transition from weight loss to maintenance: development and optimisation of a face-to-face behavioural intervention component

    PubMed Central

    Sainsbury, Kirby; Cleland, Claire L.; Evans, Elizabeth H.; Adamson, Ashley; Batterham, Alan; Dombrowski, Stephan U.; Gellert, Paul; Hill, Moira; Kwasnicka, Dominika; Scott, Dawn; Sniehotta, Falko F.; White, Martin; Araújo-Soares, Vera

    2017-01-01

    ABSTRACT After weight loss, most individuals regain lost weight. Interventions to support the transition from successful loss to weight loss maintenance (WLM), regardless of the method of prior weight loss, are needed. The aims of this study were to (1) develop a face-to-face behavioural intervention session to support overweight and obese individuals who have recently lost a clinically significant amount of weight in the transition to WLM; (2) to assess the single-session intervention for acceptability and feasibility prior to its use in a larger, 12-month, multi-component trial; and (3) to optimise the intervention session for future use based on participant feedback. Participants with a Body Mass Index of ≥25 kg/m2 prior to a ≥5% weight loss in the previous 12 months were recruited via the local government authority and community-based advertisements. Each attended the one-hour session with a trained facilitator, which focused on setting maintenance-relevant weight, eating, and physical activity goals. Semi-structured interviews were carried out immediately post-session to obtain feedback on the acceptability of this intervention component. Data were used to generate recommendations for changes to the session, which were discussed by the team, and used to optimise the session. Seventeen participants (13 female; median WL = 13%) were recruited. All participants evaluated the intervention session positively; 11 participants suggested improvements including reducing information provision in favour of greater focus on identifying and coping with barriers, and the inclusion of practical examples. The systematic refinement and optimisation process resulted in an acceptable and feasible face-to-face behavioural intervention session (described here), which will be tested as part of a multi-component intervention. We anticipate the session could be used to supplement existing support including online services, and has the potential to benefit people who have

  16. Standards for PV Modules and Components -- Recent Developments and Challenges: Preprint

    SciTech Connect

    Wohlgemuth, J. H.

    2012-10-01

    International standards play an important role in the Photovoltaic industry. Since PV is such a global industry it is critical that PV products be measured and qualified the same way everywhere in the world. IEC TC82 has developed and published a number of module and component measurement and qualification standards. These are continually being updated to take advantage of new techniques and equipment as well as better understanding of test requirements. Standards presently being updated include the third edition of IEC 61215, Crystalline Silicon Qualification and the second edition of IEC 61730, PV Module Safety Requirements. New standards under development include qualification of junction boxes, connectors, PV cables, and module integrated electronics as well as for testing the packaging used during transport of modules. After many years of effort, a draft standard on Module Energy Rating should be circulated for review soon. New activities have been undertaken to develop standards for the materials within a module and to develop tests that evaluate modules for wear-out in the field (International PV Module QA Task Force). This paper will discuss these efforts and indicate how the audience can participate in development of international standards.

  17. Development of software for computing forming information using a component based approach

    NASA Astrophysics Data System (ADS)

    Ko, Kwang Hee; Park, Jiing Seo; Kim, Jung; Kim, Young Bum; Shin, Jong Gye

    2009-12-01

    In shipbuilding industry, the manufacturing technology> has advanced at an unprecedented pace for the last decade. As a result, many automatic systems for cutting, welding, etc. have been developed and employed in the manufacturing process and accordingly the productivity has been increased drastically. Despite such improvement in the manufacturing technology', however, development of an automatic system for fabricating a curved hull plate remains at the beginning stage since hardware and software for the automation of the curved hull fabrication process should be developed differently depending on the dimensions of plates, forming methods and manufacturing processes of each shipyard. To deal with this problem, it is necessary> to create a "plug-in ''framework, which can adopt various kinds of hardware and software to construct a full automatic fabrication system. In this paper, a frame-work for automatic fabrication of curved hull plates is proposed, which consists of four components and related software. In particular the software module for computing fabrication information is developed by using the ooCBD development methodology; which can interface with other hardware and software with minimum effort. Examples of the proposed framework applied to medium and large shipyards are presented.

  18. Blood borne: bacterial components in mother’s blood influence fetal development

    PubMed Central

    Loughran, Allister J.; Tuomanen, Elaine I.

    2016-01-01

    Bacterial or viral infection of the mother during the course of pregnancy can cross the placenta and actively infect the fetus. However, especially for bacteria, it is more common for mothers to experience an infection that can be treated without overt fetal infection. In this setting, it is less well understood what the risk to fetal development is, particularly in terms of neurological development. This research highlight reviews recent findings indicating that bacterial components generated during infection of the mother can cross the placenta and activate the fetal innate immune system resulting in changes in the course of brain development and subsequent progression to postnatal cognitive disorders. Bacterial cell wall is a ubiquitous bacterial PAMP (pathogen-associated molecular pattern) known to activate inflammation through the stimulation of TLR2. Cell wall is released from bacteria during antibiotic treatment and new work shows that embryos exposed to cell wall from the mother demonstrate anomalous proliferation of neuronal precursor cells in a TLR2 dependent manner. Such proliferation increases the neuronal density of the cortical plate and alters brain architecture. Although there is no fetal death, subsequent cognitive development is significantly impaired. This model system suggests that bacterial infection of the mother and its treatment can impact fetal brain development and requires greater understanding to potentially eliminate a risk factor for cognitive disorders such as autism.

  19. First evidence of chitin as a component of the skeletal fibers of marine sponges. Part I. Verongidae (demospongia: Porifera).

    PubMed

    Ehrlich, Hermann; Maldonado, Manuel; Spindler, Klaus-Dieter; Eckert, Carsten; Hanke, Thomas; Born, René; Goebel, Caren; Simon, Paul; Heinemann, Sascha; Worch, Hartmut

    2007-07-15

    The Porifera (sponges) are often regarded as the oldest, extant metazoan phylum, also bearing the ancestral stage for most features occurring in higher animals. The absence of chitin in sponges, except for the wall of peculiar resistance bodies produced by a highly derived fresh-water group, is puzzling, since it points out chitin to be an autapomorphy for a particular sponge family rather than the ancestral condition within the metazoan lineage. By investigating the internal proteinaceous (spongin) skeleton of two demosponges (Aplysina sp. and Verongula gigantea) using a wide array of techniques (Fourier transform infrared (FTIR), Raman, X-ray, Calcofluor White Staining, Immunolabeling, and chitinase test), we show that chitin is a component of the outermost layer (cuticle) of the skeletal fibers of these demosponges. FTIR and Raman spectra, as well as X-ray difractograms consistently revealed that sponge chitin is much closer to the alpha-chitin known from other animals than to beta-chitin. These findings support the view that the occurrence of a chitin-producing system is the ancestral condition in Metazoa, and that the alpha-chitin is the primitive form in animals.

  20. The molecular, cellular, and morphological components of blood-brain barrier development during embryogenesis.

    PubMed

    Hagan, Nellwyn; Ben-Zvi, Ayal

    2015-02-01

    The blood brain barrier (BBB) is a hallmark of blood vessels in the brain and functions to protect the brain from unwanted blood born materials, support the unique metabolic needs of the brain, and define a stable environment crucial for brain homeostasis. The temporal profile of BBB development was long debated until recent studies produced convincing evidence demonstrating that the BBB is established and functional during embryogenesis. Here we review research focused on the molecular, cellular and morphological characteristics of BBB development. Our review discusses the precise temporal profile of BBB formation, the development of endothelial cell ultrastructure and the molecular components that provide sealing and transporting properties, the molecular pathways involved in the induction of BBB specific endothelial cell differentiation, the signaling pathways driving developmental angiogenesis versus barrier-genesis, and finally the contribution of other cell types to BBB formation. We examine aspects of BBB development that are still unresolved while highlighting research tools that could provide new insight to answer these open questions.

  1. An Integrated Surface Engineering Technology Development for Improving Energy Efficiency of Engine Components

    SciTech Connect

    Stephen Hsu; Liming Chang; Huan Zhan

    2009-05-31

    Frictional losses are inherent in most practical mechanical systems. The ability to control friction offers many opportunities to achieve energy conservation. Over the years, materials, lubricants, and surface modifications have been used to reduce friction in automotive and diesel engines. However, in recent years, progress in friction reduction technology has slowed because many of the inefficiencies have been eliminated. A new avenue for friction reduction is needed. Designing surfaces specifically for friction reduction with concomitant enhanced durability for various engine components has emerged recently as a viable opportunity due to advances in fabrication and surface finishing techniques. Recently, laser ablated dimples on surfaces have shown friction reduction properties and have been demonstrated successfully in conformal contacts such as seals where the speed is high and the load is low. The friction reduction mechanism in this regime appears to depend on the size, patterns, and density of dimples in the contact. This report describes modeling efforts in characterizing surface textures and understanding their mechanisms for enhanced lubrication under high contact pressure conditions. A literature survey is first presented on the development of descriptors for irregular surface features. This is followed by a study of the hydrodynamic effects of individual micro-wedge dimples using the analytical solution of the 1-D Reynolds equation and the determination of individual components of the total friction resistance. The results obtained provide a better understanding of the dimple orientation effects and the approach which may be used to further compare the friction reduction provided by different texture patterns.

  2. Part-Time Faculty and Professional Development: Notes from the Field

    ERIC Educational Resources Information Center

    Wallin, Desna L.

    2007-01-01

    As community colleges become dependent on a contingent workforce, the recruitment, retention, and motivation of quality part-time faculty become an institutional priority. This chapter presents an overview of the practices of three exemplary colleges in providing innovative professional development for part-time faculty.

  3. Development of Be-Cu bonding technologies for plasma facing component application

    SciTech Connect

    Barabash, V.; Prokofiev, Y.G.; Gurjeva, T.

    1994-12-31

    Beryllium is proposed as a main candidate armor materials for plasma facing components of ITER reactor. Be-Cu water cooled duplex structures are under consideration as a design options for divertor plates and limiters. The different bonding technologies were critically studied for analysis the possibility of manufacturing different divertor designs. Some results of the development of Be-Cu joints are presented in this report. The following bonding technologies were studied: (1) brazing, (2) solid state diffusion bonding, (3) hot isostatic pressure technology, (4) joint rolling. Different grades of Be were used in this study for future investigation of its response at high heat flux tests. The OFHC Cu and dispersion strengthened copper alloy MAGT-0.2 were chosen as a heat sink material. The non-destructive examination and microstructural studies of Be-Cu joints were carried out. The data on mechanical properties of joints are presented and discussed.

  4. Development of On-Line Monitoring Systems for High Temperature Components in Power Plants

    PubMed Central

    Zhang, Hongcai; Jia, Jiuhong; Wang, Ning; Hu, Xiaoyin; Tu, Shan-Tung; Zhou, Shaoping; Wang, Zhengdong

    2013-01-01

    To accurately detect deformation and extend the component life beyond the original design limits, structural safety monitoring techniques have attracted considerable attention in the power and process industries for decades. In this paper an on-line monitoring system for high temperature pipes in a power plant is developed. The extension-based sensing devices are amounted on straight pipes, T-Joints and elbows of a main steam pipeline. During on-site monitoring for more than two years, most of the sensors worked reliably and steadily. However, the direct strain gauge could not work for long periods because of the high temperature environment. Moreover, it is found that the installation and connection of the extensometers can have a significant influence on the measurement results. The on-line monitoring system has a good alarming function which is demonstrated by detecting a steam leakage of the header. PMID:24233026

  5. Design, process development, manufacture, test and evaluation of boron-aluminum for space shuttle components

    NASA Technical Reports Server (NTRS)

    Garrett, R. A.; Niemann, J. T.; Otto, O. R.; Brown, N. M.; Heinrich, R. E.

    1973-01-01

    A multi phase boron-aluminum design and evaluation program for space shuttle components was conducted, culminating in the fabrication of a 1.22 m (48 inch) x 1.83 m (72 inch) boron-aluminum compression panel capable of distributing a point load of 1555 kN (350,000 lbs) into a uniform running load at a temperature of 589 K (600 F). This panel was of the skin-stringer construction with two intermediate frame supports; seven unidirectional stringers varied in thickness from 5 plies to 52 plies and the skin was contoured to thicknesses ranging from 10 plies to 62 plies. Both the stringers and the skin incorporated Ti-6Al-4V titanium interleaves to increase bearing and in-plane shear strength. The discrete program phases were materials evaluation, design studies, process technology development, fabrication and assembly, and test and evaluation.

  6. A method for developing biomechanical response corridors based on principal component analysis.

    PubMed

    Sun, W; Jin, J H; Reed, M P; Gayzik, F S; Danelson, K A; Bass, C R; Zhang, J Y; Rupp, J D

    2016-10-03

    The standard method for specifying target responses for human surrogates, such as crash test dummies and human computational models, involves developing a corridor based on the distribution of a set of empirical mechanical responses. These responses are commonly normalized to account for the effects of subject body shape, size, and mass on impact response. Limitations of this method arise from the normalization techniques, which are based on the assumptions that human geometry linearly scales with size and in some cases, on simple mechanical models. To address these limitations, a new method was developed for corridor generation that applies principal component (PC) analysis to align response histories. Rather than use normalization techniques to account for the effects of subject size on impact response, linear regression models are used to model the relationship between PC features and subject characteristics. Corridors are generated using Monte Carlo simulation based on estimated distributions of PC features for each PC. This method is applied to pelvis impact force data from a recent series of lateral impact tests to develop corridor bounds for a group of signals associated with a particular subject size. Comparing to the two most common methods for response normalization, the corridors generated by the new method are narrower and better retain the features in signals that are related to subject size and body shape.

  7. Effect of dilution of stool soluble component on growth and development of Strongyloides stercoralis.

    PubMed

    Anamnart, Witthaya; Intapan, Pewpan Maleewong; Pattanawongsa, Attarat; Chamavit, Pennapa; Kaewsawat, Supreecha; Maleewong, Wanchai

    2015-06-02

    Dispersion or dilution of stool by water from heavy rainfall may affect Strongyloides stercoralis free-living development producing infective filariform larvae (FL). This study examined effect of water dilution of stool on survival of S. stercoralis free-living development. One g of stool was prepared in water so that its soluble component was diluted sequentially from 1:2 to 1:480. Three dishes were used to compare FL production in three culture conditions: stool suspension, stool sediment deposited in soil, and isolated rhabditiform larvae (RhL) deposited in soil. The fourth dish was for developmental observation of RhL into free-living stages. Numerous FL were generated from undiluted or 1:2 diluted stool and stool sediment placed on soil. However, starting from dilution 1:5, FL production continuously decreased in both stool suspensions and stool sediments placed on soil. RhL isolated from stool dilutions placed on soil gave rise to few FL. Worm mating were seen at 24-30 hours in dilutions 1:20-1:120 only. Highest numbers of FL from indirect free-living cycle were 1/3 of those from control. FL production decreased as stool dilution increased, and reached zero production at 1:160 dilution. Rainfall may disperse or dilute stool so that nutritional supplement for S. stercoralis free-living development is insufficient.

  8. Effect of dilution of stool soluble component on growth and development of Strongyloides stercoralis

    PubMed Central

    Anamnart, Witthaya; Maleewong Intapan, Pewpan; Pattanawongsa, Attarat; Chamavit, Pennapa; Kaewsawat, Supreecha; Maleewong, Wanchai

    2015-01-01

    Dispersion or dilution of stool by water from heavy rainfall may affect Strongyloides stercoralis free-living development producing infective filariform larvae (FL). This study examined effect of water dilution of stool on survival of S. stercoralis free-living development. One g of stool was prepared in water so that its soluble component was diluted sequentially from 1:2 to 1:480. Three dishes were used to compare FL production in three culture conditions: stool suspension, stool sediment deposited in soil, and isolated rhabditiform larvae (RhL) deposited in soil. The fourth dish was for developmental observation of RhL into free-living stages. Numerous FL were generated from undiluted or 1:2 diluted stool and stool sediment placed on soil. However, starting from dilution 1:5, FL production continuously decreased in both stool suspensions and stool sediments placed on soil. RhL isolated from stool dilutions placed on soil gave rise to few FL. Worm mating were seen at 24-30 hours in dilutions 1:20-1:120 only. Highest numbers of FL from indirect free-living cycle were 1/3 of those from control. FL production decreased as stool dilution increased, and reached zero production at 1:160 dilution. Rainfall may disperse or dilute stool so that nutritional supplement for S. stercoralis free-living development is insufficient. PMID:26035061

  9. Development of A General Principle Solution Forisoagrinet Compliant Networking System Components in Animal Husbandry

    NASA Astrophysics Data System (ADS)

    Kuhlmann, Arne; Herd, Daniel; Röβler, Benjamin; Gallmann, Eva; Jungbluth, Thomas

    In pig production software and electronic systems are widely used for process control and management. Unfortunately most devices on farms are proprietary solutions and autonomically working. To unify data communication of devices in agricultural husbandry, the international standard ISOagriNET (ISO 17532:2007) was developed. It defines data formats and exchange protocols, to link up devices like climate controls, feeding systems and sensors, but also management software. The aim of the research project, "Information and Data Collection in Livestock Systems" is to develop an ISOagriNET compliant IT system, a so called Farming Cell. It integrates all electronic components to acquire the available data and information for pig fattening. That way, an additional benefit to humans, animals and the environment regarding process control and documentation, can be generated. Developing the Farming Cell is very complex; in detail it is very difficult and long-winded to integrate hardware and software by various vendors into an ISOagriNET compliant IT system. This ISOagriNET prototype shows as a test environment the potential of this new standard.

  10. The flipped classroom for professional development: part II. making podcasts and videos.

    PubMed

    Smith, Charlene M; McDonald, Katie

    2013-11-01

    As described in Part I, podcasts and videos are educational technologies used to flip the classroom. This column describes the technology options for creating podcasts and videos and offers tips on developing podcasts and videos.

  11. Development of a solid polymer electrolyte electrolysis cell module and ancillary components for a breadboard water electrolysis system

    NASA Technical Reports Server (NTRS)

    Porter, F. J., Jr.

    1972-01-01

    Solid polymer electrolyte technology in a water electrolysis system along with ancillary components to generate oxygen and hydrogen for a manned space station application are considered. Standard commercial components are utilized wherever possible. Presented are the results of investigations, surveys, tests, conclusions and recommendations for future development efforts.

  12. Development of a Real-Time GPS/Seismic Displacement Meter: GPS Component

    NASA Astrophysics Data System (ADS)

    Bock, Y.; Canas, J.; Andrew, A.; Vernon, F.

    2002-12-01

    We report on the status of the Orange County Real-Time GPS Network (OCRTN), an upgrade of the SCIGN sites in Orange County and Catalina Island to low latency (1 sec), high-rate (1 Hz) data streaming, analysis, and dissemination. The project is a collaborative effort of the California Spatial Reference Center (CSRC) and the Orange County Dept. of Geomatics, with partners from the geophysical community (SCIGN), local and state government, and the private sector. As part of Phase 1 of the project, nine sites are streaming data by dedicated, point-to-point radio modems to a central data server located in Santa Ana. Instantaneous positions are computed for each site. Data are converted from 1 Hz Ashtech binary MBEN format to (1) 1 Hz RTCM format, and (2) decimated (15 sec) RINEX format. A second computer outside a firewall and located in another building at the Orange County's Computer Center is a TCP-based client of RTCM data (messages 18, 19, 3, and 22) from the data server, as well as a TCP-based server of RTCM data to the outside world. An external computer can access the RTCM data from all active sites through an IP socket connection. Data latency, in the best case, is less than 1 sec from real-time. Once a day, the decimated RINEX data are transferred by ftp from the data server to the SOPAC-CSRC archive at Scripps. Data recovery is typically 99-100%. As part of the second phase of the project, the RTCM server provides data to field receivers to perform RTK surveying. On connection to the RTCM server the user gets a list of active stations, and can then choose from which site to retrieve RTCM data. This site then plays the role of the RTK base station and a CDPD-based wireless Internet device plays the role of the normal RTK radio link. If an Internet connection is available, we will demonstrate how the system operates. This system will serve as a prototype for the GPS component of the GPS/seismic displacement meter.

  13. Development of a dual phantom technique for measuring the fast neutron component of dose in boron neutron capture therapy

    SciTech Connect

    Sakurai, Yoshinori Tanaka, Hiroki; Kondo, Natsuko; Kinashi, Yuko; Suzuki, Minoru; Masunaga, Shinichiro; Ono, Koji; Maruhashi, Akira

    2015-11-15

    Purpose: Research and development of various accelerator-based irradiation systems for boron neutron capture therapy (BNCT) is underway throughout the world. Many of these systems are nearing or have started clinical trials. Before the start of treatment with BNCT, the relative biological effectiveness (RBE) for the fast neutrons (over 10 keV) incident to the irradiation field must be estimated. Measurements of RBE are typically performed by biological experiments with a phantom. Although the dose deposition due to secondary gamma rays is dominant, the relative contributions of thermal neutrons (below 0.5 eV) and fast neutrons are virtually equivalent under typical irradiation conditions in a water and/or acrylic phantom. Uniform contributions to the dose deposited from thermal and fast neutrons are based in part on relatively inaccurate dose information for fast neutrons. This study sought to improve the accuracy in the dose estimation for fast neutrons by using two phantoms made of different materials in which the dose components can be separated according to differences in the interaction cross sections. The development of a “dual phantom technique” for measuring the fast neutron component of dose is reported. Methods: One phantom was filled with pure water. The other phantom was filled with a water solution of lithium hydroxide (LiOH) capitalizing on the absorbing characteristics of lithium-6 (Li-6) for thermal neutrons. Monte Carlo simulations were used to determine the ideal mixing ratio of Li-6 in LiOH solution. Changes in the depth dose distributions for each respective dose component along the central beam axis were used to assess the LiOH concentration at the 0, 0.001, 0.01, 0.1, 1, and 10 wt. % levels. Simulations were also performed with the phantom filled with 10 wt. % {sup 6}LiOH solution for 95%-enriched Li-6. A phantom was constructed containing 10 wt. % {sup 6}LiOH solution based on the simulation results. Experimental characterization of the

  14. Pulsed Plasma Thruster (PPT) Technology: Earth Observing-1 PPT Operational and Advanced Components Being Developed

    NASA Technical Reports Server (NTRS)

    Pencil, Eric J.; Benson, Scott W.; Arrington, Lynn A.; Frus, John; Hoskins, W. Andrew; Burton, Rodney

    2003-01-01

    In 2002 the pulsed plasma thruster (PPT) mounted on the Earth Observing-1 spacecraft was operated successfully in orbit. The two-axis thruster system is fully incorporated in the attitude determination and control system and is being used to automatically counteract disturbances in the pitch axis of the spacecraft. The first tests conducted in space demonstrated the full range of PPT operation, followed by calibration of control torques from the PPT in the attitude control system. Then the spacecraft was placed in PPT control mode. To date, it has operated for about 30 hr. The PPT successfully controlled pitch momentum during wheel de-spin, solar array acceleration and deceleration during array rewind, and environmental torques in nominal operating conditions. Images collected with the Advanced Landsat Imager during PPT operation have demonstrated that there was no degradation in comparison to full momentum wheel control. In addition, other experiments have been performed to interrogate the effects of PPT operation on communication packages and light reflection from spacecraft surfaces. Future experiments will investigate the possibility of orbit-raising maneuvers, spacecraft roll, and concurrent operation with the Hyperion imager. Future applications envisioned for pulsed plasma thrusters include longer life, higher precision, multiaxis thruster configurations for three-axis attitude control systems or high-precision, formationflying systems. Advanced components, such as a "dry" mica-foil capacitor, a wear-resistant spark plug, and a multichannel power processing unit have been developed under contract with Unison Industries, General Dynamics, and C.U. Aerospace. Over the last year, evaluation tests have been conducted to determine power processing unit efficiency, atmospheric functionality, vacuum functionality, thruster performance evaluation, thermal performance, and component life.

  15. Process development for electron beam joining of ceramic and glass components

    SciTech Connect

    Turman, B.N.; Glass, S.J.; Yang, P.; Gerstle, F.P.; Halbleib, J.A.; Voth, T.E.; McKenzie, B.; Clifford, J.R.; Habiger, K.

    1997-11-01

    The purpose of this project is to develop and extend the electron beam joining process to applications related to Mo/Al{sub 2}O{sub 3} cermets for neutron tube fabrication, glass seals for flat panel displays, and ceramics for structural applications. The key issue is the identification of the allowable operating ranges that produce thermal conditions favorable to robust joining and sealing. High strength, hermetic braze joints between ceramic components have been produced using high energy electron beams. With a penetration depth into a typical ceramic of {approximately} 1 cm for a 10 MeV electron beam, this method provides the capability for rapid, transient brazing operations where temperature control of heat sensitive components is essential. The method deposits energy directly into a buried joint, allowing otherwise inaccessible interfaces to be brazed. The combination of transient heating, with higher thermal conductivity, lower heat capacity, and lower melting temperature of braze metals relative to the ceramic materials, enables a pulsed high power beam to melt a braze metal without producing excessive ceramic temperatures. The authors have demonstrated the feasibility of this process related to ceramic coupons a well as ceramic and glass tubes and cylindrical shapes. The transient thermal response was predicted, using as input the energy absorption predicted from the coupled electron-photon and thermal transport analysis. The joining experiments were conducted with an RF linear accelerator at 10--13 MV. Joining experiments have provided high strength joints between alumina and alumina and between alumina and cermet joints in cylindrical geometry. These joints provided good hermetic seals.

  16. Development of Standardized Power Electronic Components, Subsystems, and Systems for Increased Modularity and Scalability

    SciTech Connect

    Chakraborty, S.; Pink, C.; Price, J.; Kroposki, B.; Kern, G.

    2007-11-01

    Power electronics devices hold substantial promise for making distributed energy applications more efficient and cost effective. This project is motivated towards developing and testing inverters that will allow distributed energy systems to provide ancillary services such as voltage and VAR regulation, and increased grid reliability by seamlessly transitioning between grid-tied and stand-alone operation modes. The objectives of this project are to identify system integration and optimization issues and technologies and to provide solutions through research, analysis, and testing of power electronic interfaces for distributed energy applications that are cost-competitive and have substantially faster response times than conventional technologies. In addition, the testing of power electronics interfaces will develop a technical basis for performance assessment for distributed energy systems, subsystems, and components that will finally create a foundation for standardized measurements and test procedures. The ultimate goal for this research is to advance the potential benefits of distributed energy to provide ancillary services, enhance power system reliability, and allow customer choice.

  17. The microprocessor component, DGCR8, is essential for early B-cell development in mice.

    PubMed

    Brandl, Andreas; Daum, Patrick; Brenner, Sven; Schulz, Sebastian R; Yap, Desmond Yat-Hin; Bösl, Michael R; Wittmann, Jürgen; Schuh, Wolfgang; Jäck, Hans-Martin

    2016-12-01

    microRNAs (miRNAs) are important posttranscriptional regulators during hematopoietic lineage commitment and lymphocyte development. Mature miRNAs are processed from primary miRNA transcripts in two steps by the microprocessor complex, consisting of Drosha and its partner DiGeorge Critical Region 8 (DGCR8), and the RNAse III enzyme, Dicer. Conditional ablations of Drosha and Dicer have established the importance of both RNAses in B- and T-cell development. Here, we show that a cre-mediated B-cell specific deletion of DGCR8 in mice results in a nearly complete maturation block at the transition from the pro-B to the pre-B cell stage, and a failure to upregulate Ig μ heavy chain expression in pro-B cells. Furthermore, we found that the death of freshly isolated DGCR8-deficient pro-B cells could be partially prevented by enforced Bcl2 expression. We conclude from these findings that the microprocessor component DGCR8 is essential for survival and differentiation of early B-cell progenitors.

  18. Gawky is a component of cytoplasmic mRNA processing bodies required for early Drosophila development

    PubMed Central

    Schneider, Mary D.; Najand, Nima; Chaker, Sana; Pare, Justin M.; Haskins, Julie; Hughes, Sarah C.; Hobman, Tom C.; Locke, John; Simmonds, Andrew J.

    2006-01-01

    In mammalian cells, the GW182 protein localizes to cytoplasmic bodies implicated in the regulation of messenger RNA (mRNA) stability, translation, and the RNA interference pathway. Many of these functions have also been assigned to analogous yeast cytoplasmic mRNA processing bodies. We have characterized the single Drosophila melanogaster homologue of the human GW182 protein family, which we have named Gawky (GW). Drosophila GW localizes to punctate, cytoplasmic foci in an RNA-dependent manner. Drosophila GW bodies (GWBs) appear to function analogously to human GWBs, as human GW182 colocalizes with GW when expressed in Drosophila cells. The RNA-induced silencing complex component Argonaute2 and orthologues of LSm4 and Xrn1 (Pacman) associated with 5′–3′ mRNA degradation localize to some GWBs. Reducing GW activity by mutation or antibody injection during syncytial embryo development leads to abnormal nuclear divisions, demonstrating an early requirement for GWB-mediated cytoplasmic mRNA regulation. This suggests that gw represents a previously unknown member of a small group of genes that need to be expressed zygotically during early embryo development. PMID:16880270

  19. Localization of extracellular matrix components in developing mouse salivary glands by confocal microscopy

    NASA Technical Reports Server (NTRS)

    Hardman, P.; Spooner, B. S.

    1992-01-01

    The importance of the extracellular matrix (ECM) in epithelial-mesenchymal interactions in developing organisms is well established. Proteoglycans and interstitial collagens are required for the growth, morphogenesis, and differentiation of epithelial organs and the distribution of these molecules has been described. However, much less is known about other ECM macromolecules in developing epithelial organs. We used confocal microscopy to examine the distribution of laminin, heparan sulfate (BM-1) proteoglycan, fibronectin, and collagen types I, IV, and V, in mouse embryonic salivary glands. Organ rudiments were isolated from gestational day 13 mouse embryos and cultured for 24, 48, or 72 hours. Whole mounts were stained by indirect immunofluorescence and then examined using a Zeiss Laser Scan Microscope. We found that each ECM component examined had a distinct distribution and that the distribution of some molecules varied with culture time. Laminin was mainly restricted to the basement membrane. BM-1 proteoglycan was concentrated in the basement membrane and also formed a fine network throughout the mesenchyme. Type IV collagen was mainly located in the basement membrane of the epithelium, but it was also present throughout the mesenchyme. Type V collagen was distributed throughout the mesenchyme at 24 hours, but at 48 hours was principally located in the basement membrane. Type I collagen was distributed throughout the mesenchyme at all culture times, and accumulated in the clefts and particularly at the epithelial-mesenchymal interface as time in culture increased. Fibronectin was observed throughout the mesenchyme at all times.

  20. Development of active polyvinyl alcohol/β-cyclodextrin composites to scavenge undesirable food components.

    PubMed

    López-de-Dicastillo, Carol; Jordá, María; Catalá, Ramón; Gavara, Rafael; Hernández-Muñoz, Pilar

    2011-10-26

    Active food packaging systems based on the incorporation of agents into polymeric package walls are being designed to purposely release or retain compounds to maintain or even increase food quality. The objective of this work was to develop polyvinyl alcohol (PVOH)/β-cyclodextrin (βCD) composite films that can be applied to reduce undesirable component content such as cholesterol in foods through active retention of the compounds in the package walls during storage. Cyclodextrins were added to PVOH in a proportion of 1:1 and cross-linked with glyoxal under acidic media to reduce its water-soluble character. Three different cross-linking procedures were used: cross-linking of the polymer/polysaccharide mixture in solution and film casting, PVOH. βCD*; cross-linking of the polymer, addition of βCD, and casting of the mixture, PVOH*.CD; and casting of a PVOH film, addition of a βCD/glyoxal solution onto the film, and cross-linking during drying, PVOH.CD*. Characterization studies showed that the PVOH*.CD and PVOH.CD* films provided the best physical characteristics with the lowest release values and the highest barrier properties. As a potential application, materials were tested as potential cholesterol-scavenging films. There was a significant reduction in the cholesterol concentration in milk samples when they were exposed to the materials developed.

  1. Recent development in liquid chromatography stationary phases for separation of Traditional Chinese Medicine components.

    PubMed

    Jin, Hongli; Liu, Yanfang; Guo, Zhimou; Wang, Jixia; Zhang, Xiuli; Wang, Chaoran; Liang, Xinmiao

    2016-10-25

    Traditional Chinese Medicine (TCM) is an ancient medical practice which has been used to prevent and cure diseases for thousands of years. TCMs are frequently multi-component systems with mainly unidentified constituents. The study of the chemical compositions of TCMs remains a hotspot of research. Different strategies have been developed to manage the significant complexity of TCMs, in an attempt to determine their constituents. Reversed-phase liquid chromatography (RPLC) is still the method of choice for the separation of TCMs, but has many problems related to limited selectivity. Recently, enormous efforts have been concentrated on the development of efficient liquid chromatography (LC) methods for TCMs, based on selective stationary phases. This can improve the resolution and peak capacity considerably. In addition, high-efficiency stationary phases have been applied in the analysis of TCMs since the invention of ultra high-performance liquid chromatography (UHPLC). This review describes the advances in LC methods in TCM research from 2010 to date, and focuses on novel stationary phases. Their potential in the separation of TCMs using relevant applications is also demonstrated.

  2. The response of fluid-saturated reservoirs to lunisolar tides: Part 1. Background parameters of tidal components in ground displacements and groundwater level

    NASA Astrophysics Data System (ADS)

    Besedina, A. N.; Vinogradov, E. A.; Gorbunova, E. M.; Kabychenko, N. V.; Svintsov, I. S.; Pigulevskiy, P. I.; Svistun, V. K.; Shcherbina, S. V.

    2015-01-01

    The first part of this work is dedicated to the response of different-age structures to lunisolar tides, which can be considered as a sounding signal for monitoring the state of fluid-saturated reservoirs. The complex approach to processing the data obtained at the testing sites of the Institute of Geosphere Dynamics of the Russian Academy of Sciences, Institute of Geophysics of the National Academy of Sciences of Ukraine, and KIEV station of the IRIS seismic network is applied for recognizing the tides against the hydrogeological, barometric, and seismic series. The comparative analysis of the experimental and theoretical values of the diurnal and semidiurnal tidal components in the time series of ground displacements is carried out. The tidal variations in the groundwater level are compared with the tidal components revealed in the ground displacement of the different-age structure of the Moscow Basin and Ukrainian Shield, which are parts of the East European artesian region. The differences in the tidal responses of the groundwater level and ground displacement probably suggest that the state of the massif is affected by certain additional factors associated, e.g., with the passage of earthquake-induced seismic waves and the changes in the hydrogeodynamic environment.

  3. Database Development for Electrical, Electronic, and Electromechanical (EEE) Parts for the International Space Station Alpha

    NASA Technical Reports Server (NTRS)

    Wassil-Grimm, Andrew D.

    1997-01-01

    More effective electronic communication processes are needed to transfer contractor and international partner data into NASA and prime contractor baseline database systems. It is estimated that the International Space Station Alpha (ISSA) parts database will contain up to one million parts each of which may require database capabilities for approximately one thousand bytes of data for each part. The resulting gigabyte database must provide easy access to users who will be preparing multiple analyses and reports in order to verify as-designed, as-built, launch, on-orbit, and return configurations for up to 45 missions associated with the construction of the ISSA. Additionally, Internet access to this data base is strongly indicated to allow multiple user access from clients located in many foreign countries. This summer's project involved familiarization and evaluation of the ISSA Electrical, Electronic, and Electromechanical (EEE) Parts data and the process of electronically managing these data. Particular attention was devoted to improving the interfaces among the many elements of the ISSA information system and its global customers and suppliers. Additionally, prototype queries were developed to facilitate the identification of data changes in the data base, verifications that the designs used only approved parts, and certifications that the flight hardware containing EEE parts was ready for flight. This project also resulted in specific recommendations to NASA for further development in the area of EEE parts database development and usage.

  4. Development of a component design tool for metal hydride heat pumps

    NASA Astrophysics Data System (ADS)

    Waters, Essene L.

    Given current demands for more efficient and environmentally friendly energy sources, hydrogen based energy systems are an increasingly popular field of interest. Within the field, metal hydrides have become a prominent focus of research due to their large hydrogen storage capacity and relative system simplicity and safety. Metal hydride heat pumps constitute one such application, in which heat and hydrogen are transferred to and from metal hydrides. While a significant amount of work has been done to study such systems, the scope of materials selection has been quite limited. Typical studies compare only a few metal hydride materials and provide limited justification for the choice of those few. In this work, a metal hydride component design tool has been developed to enable the targeted down-selection of an extensive database of metal hydrides to identify the most promising materials for use in metal hydride thermal systems. The material database contains over 300 metal hydrides with various physical and thermodynamic properties included for each material. Sub-models for equilibrium pressure, thermophysical data, and default properties are used to predict the behavior of each material within the given system. For a given thermal system, this tool can be used to identify optimal materials out of over 100,000 possible hydride combinations. The selection tool described herein has been applied to a stationary combined heat and power system containing a high-temperature proton exchange membrane (PEM) fuel cell, a hot water tank, and two metal hydride beds used as a heat pump. A variety of factors can be used to select materials including efficiency, maximum and minimum system pressures, pressure difference, coefficient of performance (COP), and COP sensitivity. The targeted down-selection of metal hydrides for this system focuses on the system's COP for each potential pair. The values of COP and COP sensitivity have been used to identify pairs of highest interest for

  5. Development of linear and nonlinear components for integrated optical signal processing

    NASA Astrophysics Data System (ADS)

    Tseng, Shuo-Yen

    Optical processors have potentially a major advantage over electronic processors because of their tremendous bandwidth. Massive parallelism is another inherent advantage of optical processors. However, it is traditionally demonstrated with free space components and seldom used for integrated optical signal processing. In this thesis, we consider spatial domain signal processing in guided wave structures, which brings a new dimension to the existing serial signal processing architecture and takes advantage of the parallelism in optics. A novel class of devices using holograms in multimode channel waveguides is developed in this work. Linear optical signal processing using multimode waveguide holograms (MWHs) is analyzed. We focus on discrete unitary transformations to take advantage of the discrete nature of modes in multimode waveguides. We prove that arbitrary unitary transformations can be performed using holograms in multimode waveguides. A model using the wide-angle beam propagation method (WA-BPM) is developed to simulate the devices and shows good agreement with the theory. The design principle of MWH devices is introduced. Based on the design principle, BPM models are used to design several devices including a mode-order converter, a Hadamard transformer, and an optical pattern generator/correlator. Optical pattern generators are fabricated to verify the theory and the model. Also, the bandwidth and fabrication tolerance of MWH devices are also analyzed. Also, we examine the nonlinear optical switches which allow the integration of MWHs into modern optical communication networks. A simple optical setup using an imaged 2-D phase grating is developed for characterization of the complex third-order nonlinearity chi(3) to identify suitable nonlinear materials for integrated optical switches. This technique provides a reliable way to characterize chi(3) as new materials are constantly being developed. Finally, we demonstrate the concept of optical switching using

  6. Rat pup social motivation: A critical component of early psychological development

    PubMed Central

    Cromwell, Howard Casey

    2011-01-01

    Examining the role of the offspring in early social dynamics is especially difficult. Human developmental psychology has found infant behavior to be a vital part of the early environmental setting. In the rodent model, the different ways that a rodent neonate or pup can influence social dynamics are not well known. Typically, litters of neonates or pups offer complex social interactions dominated by behavior seemingly initiated and maintained by the primary caregiver (e.g., the dam). Despite this strong role for the caregiver, the young most likely influence the litter dynamics in many powerful ways including communication signals, discrimination abilities and early approach behavior. Nelson and Panksepp (1996) developed a preference task to examine early rodent pup social motivation. We have used the same task to examine how variations in maternal care or different environmental perturbations could alter the rat pup preferences for social-related stimuli. Rat pups receiving low levels of maternal licking and grooming were impaired in maternal odor cue learning and emitted lower levels of 22 kHz ultrasounds compared to pups from the high licking and grooming cohort. Prenatal stress or early exposure to a toxicant (polychlorinated biphenyl) altered early social preferences in the rat pup in different ways indicating that diverse strategies are expressed and specific to the type of perturbation exposure. A greater focus on the offspring motivation following early ‘stressors’ will allow for more complete understanding of the dynamics in behavior during early social development. PMID:21251926

  7. A Basis for Skills Developing the "College for Business" in Sussex: Part of an LSDA Collection.

    ERIC Educational Resources Information Center

    Hughes, Maria; Stanton, Geoff

    As part of its ongoing efforts to improve further education (FE) in the United Kingdom, the Learning and Skills Development Agency (LSDA) developed a model for FE colleges that see their core purpose as meeting the needs of business and industry as distinct form colleges with a mission to serve the needs of the community or prepare young people…

  8. Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1994--September 30, 1995

    SciTech Connect

    Hoppe, M.

    1996-05-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities of the period October 1, 1994 through September 30, 1995. During this period, GA was assigned 15 tasks in support of the Inertial Confinement Fusion program and its laboratories. A portion of the effort on these tasks included providing direct ``Onsite Support`` at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). The ICF program is anticipating experiments at the National Ignition Facility (NIF) and the OMEGA Upgrade. Both facilities will require capsules containing layered D{sub 2} or deuterium-tritium (D-T) fuel. The authors are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Progress has been made on ways to both create viable layers and to characterize them. They continued engineering, assembly and testing of equipment for a cryogenic target handling system for University of Rochester`s Laboratory for Laser Energetics (UR/LLE) that will fill, transport, layer, and characterize targets filled with cryogenic fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments. This report summarizes and documents the technical progress made on these tasks.

  9. A Technology for Developing Instructional Materials. Vol. 3, Handbook. Part F, Develop Diagnostic and Evaluative Tests.

    ERIC Educational Resources Information Center

    Gropper, George L.

    This document, sixth in a series of 11 subvolumes of a handbook prepared to provide training for educational research and development personnel in the development of instructional materials, deals with the task of developing diagnostic and evaluative tests. The document is organized according to the four sequential steps involved in performing the…

  10. Development and evaluation of components for a totally implantable artificial heart system.

    PubMed

    Taenaka, Y; Masuzawa, T; Tatsumi, F; Anai, H; Toda, K; Akagi, H; Nakatani, T; Baba, Y; Fya, K; Wakisaka, Y

    1994-01-01

    The authors have been developing an electrohydraulic (EH) artificial heart system for total implantation. This system consists of intrathoracic ventricles, an abdominally placed EH actuator, flexible silicone oil conduits, externally coupled transcutaneous energy transfer (TET) system, transcutaneous optical telemetry (TOT) system, internal battery, and internal control drive unit. Fitting was evaluated in chronic animal experiments as a pneumatic system in 11 goats weighing 55.2 +/- 4.2 kg and 3 calves of 52.3 +/- 1.2 kg. The longest survival time in calves was 111 days, and that in goats was 51 days. The assembled EH pump was implanted in two goats of 49 and 50 kg as an acute experiment, and 4.2-6.7 L/min of cardiac output was maintained. For the TET system, an internal coil 3 cm in diameter was implanted to make an arch covered by skin. Electric energy was transmitted from the external to the internal coil, and energy of about 20 W was carried through wires to an external load. The DC-to-DC efficiency of the system was 76-83% for 40 days. The TOT system with internal light emitting diodes and external photodiodes also was evaluated in a goat. Disalignment of up to 12 mm was tolerated. Although more improvement is necessary, most of the components showed characteristics desirable for a totally implantable system.

  11. Enhancing the mental health promotion component of a health and personal development programme in Irish schools

    PubMed Central

    Fitzpatrick, Carol; Conlon, Andrea; Cleary, Deirdre; Power, Mike; King, Frances; Guerin, Suzanne

    2013-01-01

    This study set out to examine the impact of a health and personal development programme (the Social, Personal and Health Education Programme) which had been ‘enhanced’ by the addition of a mental health promotion component. Students aged 12–16 years attending 17 secondary schools were randomly allocated as clusters to participate in either the standard programme (SP) or the enhanced programme (EP). Both programmes were delivered over an eight-month period. Questionnaires assessing help-seeking, emotional and behavioural difficulties and students’ views of school social environment were completed by students in both groups at pre-intervention, post-intervention and at six-month follow-up. One thousand and seventy-two students participated. Analyses were carried out on the 782 students (72.9%) for whom data were available at all three time points. Both groups showed improvement over time in terms of emotional and behavioural difficulties, with male students identified as ‘at risk’ in the EP showing significantly greater improvements than males ‘at risk’ in the SP. Although there were few differences in outcomes between the groups, males identified as ‘at risk’ appeared to benefit selectively from the EP. PMID:23730327

  12. Development Of Model P-302 Beryllium Rotating Mirror Component In High Speed Streak Camera

    NASA Astrophysics Data System (ADS)

    Sang, Yongsheng

    1989-06-01

    This paper depicts the development and test of Model P-302 Beryllium Rotating Mirror Component used in Model WPG-30 or Model SJZ-15 Streak Camera. The mirror body is made of Hot lsostatic Pressing (HIP) Beryllium. The mirror reflective surface is made by replica film method and consists of 0.1 wave-length flatness beryllium substrate with an aluminum overcoating. Its reflectance is 83%. The cavity of the rotating mirror is not vacuumized. The rotor is strictly adjusted with the dynamic balance method. The turbine is driven by compressive-air and the maximum rotating speed in test is 5,833 rps. The size of the mirror body is 22.5X25 mmX8 mm (rotating diameter is 22.5 mm). Under examination of dynamic performance its writing rate is 15 km/s, the time resolution is 1.4 ns (0.01 mm slit width), the dynamic resolution in scanning direction is 28 line pairs/mm and the effective aperture at film is 1/10.6. The results for detonation experiments indicated that when its rotating speed was 5,000rps, the image density was suitable for measurement while using 36 DIN film. And the results also showed that the precision of measurement have been greatly improved as compared with the steel rotating mirror used before.

  13. The Component Packaging Problem: A Vehicle for the Development of Multidisciplinary Design and Analysis Methodologies

    NASA Technical Reports Server (NTRS)

    Fadel, Georges; Bridgewood, Michael; Figliola, Richard; Greenstein, Joel; Kostreva, Michael; Nowaczyk, Ronald; Stevenson, Steve

    1999-01-01

    This report summarizes academic research which has resulted in an increased appreciation for multidisciplinary efforts among our students, colleagues and administrators. It has also generated a number of research ideas that emerged from the interaction between disciplines. Overall, 17 undergraduate students and 16 graduate students benefited directly from the NASA grant: an additional 11 graduate students were impacted and participated without financial support from NASA. The work resulted in 16 theses (with 7 to be completed in the near future), 67 papers or reports mostly published in 8 journals and/or presented at various conferences (a total of 83 papers, presentations and reports published based on NASA inspired or supported work). In addition, the faculty and students presented related work at many meetings, and continuing work has been proposed to NSF, the Army, Industry and other state and federal institutions to continue efforts in the direction of multidisciplinary and recently multi-objective design and analysis. The specific problem addressed is component packing which was solved as a multi-objective problem using iterative genetic algorithms and decomposition. Further testing and refinement of the methodology developed is presently under investigation. Teaming issues research and classes resulted in the publication of a web site, (http://design.eng.clemson.edu/psych4991) which provides pointers and techniques to interested parties. Specific advantages of using iterative genetic algorithms, hurdles faced and resolved, and institutional difficulties associated with multi-discipline teaming are described in some detail.

  14. Analytical Method to Evaluate Failure Potential During High-Risk Component Development

    NASA Technical Reports Server (NTRS)

    Tumer, Irem Y.; Stone, Robert B.; Clancy, Daniel (Technical Monitor)

    2001-01-01

    Communicating failure mode information during design and manufacturing is a crucial task for failure prevention. Most processes use Failure Modes and Effects types of analyses, as well as prior knowledge and experience, to determine the potential modes of failures a product might encounter during its lifetime. When new products are being considered and designed, this knowledge and information is expanded upon to help designers extrapolate based on their similarity with existing products and the potential design tradeoffs. This paper makes use of similarities and tradeoffs that exist between different failure modes based on the functionality of each component/product. In this light, a function-failure method is developed to help the design of new products with solutions for functions that eliminate or reduce the potential of a failure mode. The method is applied to a simplified rotating machinery example in this paper, and is proposed as a means to account for helicopter failure modes during design and production, addressing stringent safety and performance requirements for NASA applications.

  15. Evaluation of Preproduction Hardware Components for IMS Station Upgrades to Reduce Manufacturers Development Time

    NASA Astrophysics Data System (ADS)

    Hart, Darren; Pearce, Nathan; Starovoit, Yuri; Guralp, Cansun

    2014-05-01

    Since the Comprehensive Nuclear-Test-Ban Treaty was opened for signature in 1996, nearly 80% of the network has been certified as operational, and those stations are sending data to the International Data Centre (IDC) in Vienna. Several International Monitoring System (IMS) monitoring facilities have been in operation for close to 15 years, and several certified stations are facing equipment obsolescence issues. The search for engineering solutions to replace obsolete hardware components is guided by two primary goals: 1) be compliant with IMS minimum technical requirements and 2) be able to be integrated with the existing system. To reduce the development and verification time necessary to address obsolescence in equipment, the PTS has requested the preproduction testing of the recently revised Guralp CMG-DM24AM digitizer. Performing preproduction testing has helped in identifying issues, which Guralp Systems has resolved. In our poster, we will review the reasons for the digitizer updates, present results of the preproduction testing of the Guralp digitizer, and comment on the value this process has provided to the IMS operation.

  16. Recent developments in Medicare Part D: 7 things providers should know.

    PubMed

    Grimaldi, Paul L

    2007-03-01

    Providers should be aware of the following recent developments in the Medicare Part D program: The standard plan will cost more in 2007. The coverage gap will remain a source of discontent. The recently streamlined Drug Plan Finder eases decision making. The weighting method used to calculate the national average bid has been modified. The Part D audit guide has been finalized. Rebates and other price concessions face greater scrutiny. There is renewed debate over negotiated drug prices.

  17. "Looking and Feeling the Part": Developing Aviation Students' Professional Identity through a Community of Practice

    ERIC Educational Resources Information Center

    O'Brien, Wendy; Bates, Paul

    2015-01-01

    For students entering a profession with a strong vocational focus, the development of professional identity and attributes are important components of successful professional practice. Familiarity with the norms and culture of a specific profession are not often addressed within normal curricula contexts of undergraduate degrees. At Griffith…

  18. Development and setting of a new system for advanced rheocast components

    SciTech Connect

    Rosso, Mario; Peter, I.; Calosso, F.

    2011-05-04

    This paper presents an overview of alternative methods of production of enhanced performance Al-based alloys components for critical areas. In particular, a new rheocasting system, suitable for the manufacturing of high performance industrial components has been considered. The aforementioned method allows obtaining component quickly and results a more convenient process, from economical point of view than other innovative processes. Two series of components have been produced with A356 and A357 alloys, then have been heat treated using T5 and T6 treatments. On polished transverse sections of samples the microstructure of the alloy has been observed. Their soundness has been previously certified by non destructive tests. Samples for tensile and three point bending tests have been machined directly from the produced components. On the fractured samples, fracture surface analysis has been performed in order to analyze and evaluate the influence of the process and of the alloy on the fracture behaviour.

  19. Development and setting of a new system for advanced rheocast components

    NASA Astrophysics Data System (ADS)

    Rosso, Mario; Peter, I.; Calosso, F.

    2011-05-01

    This paper presents an overview of alternative methods of production of enhanced performance Al-based alloys components for critical areas. In particular, a new rheocasting system, suitable for the manufacturing of high performance industrial components has been considered. The aforementioned method allows obtaining component quickly and results a more convenient process, from economical point of view than other innovative processes. Two series of components have been produced with A356 and A357 alloys, then have been heat treated using T5 and T6 treatments. On polished transverse sections of samples the microstructure of the alloy has been observed. Their soundness has been previously certified by non destructive tests. Samples for tensile and three point bending tests have been machined directly from the produced components. On the fractured samples, fracture surface analysis has been performed in order to analyze and evaluate the influence of the process and of the alloy on the fracture behaviour.

  20. Roadmap for Developing of Brokering as a Component of EarthCube

    NASA Astrophysics Data System (ADS)

    Pearlman, J.; Khalsa, S. S.; Browdy, S.; Duerr, R. E.; Nativi, S.; Parsons, M. A.; Pearlman, F.; Robinson, E. M.

    2012-12-01

    The goal of NSF's EarthCube is to create a sustainable infrastructure that enables the sharing of all geosciences data, information, and knowledge in an open, transparent and inclusive manner. Key to achieving the EarthCube vision is establishing a process that will guide the evolution of the infrastructure through community engagement and appropriate investment so that the infrastructure is embraced and utilized by the entire geosciences community. In this presentation we describe a roadmap, developed through the EarthCube Brokering Concept Award, for an evolutionary process of infrastructure and interoperability development. All geoscience communities already have, to a greater or lesser degree, elements of an information infrastructure in place. These elements include resources such as data archives, catalogs, and portals as well as vocabularies, data models, protocols, best practices and other community conventions. What is necessary now is a process for consolidating these diverse infrastructure elements into an overall infrastructure that provides easy discovery, access and utilization of resources across disciplinary boundaries. This process of consolidation will be achieved by creating "interfaces," what we call "brokers," between systems. Brokers connect disparate systems without imposing new burdens upon those systems, and enable the infrastructure to adjust to new technical developments and scientific requirements as they emerge. Robust cyberinfrastructure will arise only when social, organizational, and cultural issues are resolved in tandem with the creation of technology-based services. This is best done through use-case-driven requirements and agile, iterative development methods. It is important to start by solving real (not hypothetical) information access and use problems via small pilot projects that develop capabilities targeted to specific communities. These pilots can then grow into larger prototypes addressing intercommunity problems working

  1. Development of Hydrometeorological Monitoring and Forecasting as AN Essential Component of the Early Flood Warning System:

    NASA Astrophysics Data System (ADS)

    Manukalo, V.

    2012-12-01

    Defining issue The river inundations are the most common and destructive natural hazards in Ukraine. Among non-structural flood management and protection measures a creation of the Early Flood Warning System is extremely important to be able to timely recognize dangerous situations in the flood-prone areas. Hydrometeorological information and forecasts are a core importance in this system. The primary factors affecting reliability and a lead - time of forecasts include: accuracy, speed and reliability with which real - time data are collected. The existing individual conception of monitoring and forecasting resulted in a need in reconsideration of the concept of integrated monitoring and forecasting approach - from "sensors to database and forecasters". Result presentation The Project: "Development of Flood Monitoring and Forecasting in the Ukrainian part of the Dniester River Basin" is presented. The project is developed by the Ukrainian Hydrometeorological Service in a conjunction with the Water Management Agency and the Energy Company "Ukrhydroenergo". The implementation of the Project is funded by the Ukrainian Government and the World Bank. The author is nominated as the responsible person for coordination of activity of organizations involved in the Project. The term of the Project implementation: 2012 - 2014. The principal objectives of the Project are: a) designing integrated automatic hydrometeorological measurement network (including using remote sensing technologies); b) hydrometeorological GIS database construction and coupling with electronic maps for flood risk assessment; c) interface-construction classic numerical database -GIS and with satellite images, and radar data collection; d) providing the real-time data dissemination from observation points to forecasting centers; e) developing hydrometeoroogical forecasting methods; f) providing a flood hazards risk assessment for different temporal and spatial scales; g) providing a dissemination of

  2. FISCAL YEAR 2006 REPORT ON ELECTROLYZER COMPONENT DEVELOPMENT FOR THE HYBRID SULFUR PROJECT

    SciTech Connect

    Colon-Mercado, H; David Hobbs, D; Daryl Coleman, D; Amy Ekechukwu, A

    2006-08-03

    Thermochemical processes are being developed to provide global-scale quantities of hydrogen. A variant on sulfur-based thermochemical cycles is the Hybrid Sulfur (HyS) Process which uses a sulfur dioxide depolarized electrolyzer (SDE) to produce the hydrogen. In FY05, testing at the Savannah River National Laboratory (SRNL) explored a low temperature fuel cell design concept for the SDE. The advantages of this design concept include high electrochemical efficiency and small volumetric footprint that is crucial for successful implementation on a commercial scale. A key component of the SDE is the ion conductive membrane through which protons produced at anode migrate to the cathode and react to produce hydrogen. An ideal membrane for the SDE should have both low ionic resistivity and low sulfur dioxide transport. These features allow the electrolyzer to perform at high currents with low potentials, along with preventing contamination of both the hydrogen output and poisoning of the catalysts involved. Another key component is the electrocatalyst material used for the anode and cathode. Good electrocatalysts should be chemically stable and low overpotential for the desired electrochemical reactions. This report summarizes results from activities to evaluate different membrane and electrocatalyst materials for the SDE. Several different types of commercially-available membranes were analyzed for ionic resistance and sulfur dioxide transport including perfluorinated sulfonic acid, sulfonated poly-etherketone-ketone, and poly-benzimidazole membranes. Of these membrane types, the poly-benzimidazole (PBI) membrane, Celtec-L, exhibited the best combination of characteristics for use in an SDE. Testing examined the activity and stability of platinum and palladium as electrocatalyst for the SDE in sulfuric acid solutions. Cyclic and linear sweep voltammetry revealed that platinum provided better catalytic activity with much lower potentials and higher currents than palladium

  3. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1995--September 30, 1996

    SciTech Connect

    Hoppe, M.

    1997-02-01

    On December 30, 1990, the U.S. Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. In September 1995 this contract ended and a second contract was issued for us to continue this ICF target support work. This report documents the technical activities of the period October 1, 1995 through September 30, 1996. During this period, GA and our partners WJ Schafer Associates (WJSA) and Soane Technologies, Inc. (STI) were assigned 14 formal tasks in support of the Inertial Confinement Fusion program and its five laboratories. A portion of the effort on these tasks included providing direct {open_quotes}Onsite Support{close_quotes} at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). We fabricated and delivered over 800 gold-plated hohlraum mandrels to LLNL, LANL and SNLA. We produced nearly 1,200 glass and plastic target capsules for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). We also delivered over 100 flat foil targets for Naval Research Lab (NRL) and SNLA in FY96. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require capsules containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. We are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Substantial progress has been made on ways to both create and characterize viable layers. During FY96, significant progress was made in the design of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA.

  4. Development of Evaluation Methods for Lower Limb Function between Aged and Young Using Principal Component Analysis

    NASA Astrophysics Data System (ADS)

    Nomoto, Yohei; Yamashita, Kazuhiko; Ohya, Tetsuya; Koyama, Hironori; Kawasumi, Masashi

    There is the increasing concern of the society to prevent the fall of the aged. The improvement in aged people's the muscular strength of the lower-limb, postural control and walking ability are important for quality of life and fall prevention. The aim of this study was to develop multiple evaluation methods in order to advise for improvement and maintenance of lower limb function between aged and young. The subjects were 16 healthy young volunteers (mean ± S.D: 19.9 ± 0.6 years) and 10 healthy aged volunteers (mean ± S.D: 80.6 ± 6.1 years). Measurement items related to lower limb function were selected from the items which we have ever used. Selected measurement items of function of lower are distance of extroversion of the toe, angle of flexion of the toe, maximum width of step, knee elevation, moving distance of greater trochanter, walking balance, toe-gap force and rotation range of ankle joint. Measurement items summarized by the principal component analysis into lower ability evaluation methods including walking ability and muscle strength of lower limb and flexibility of ankle. The young group demonstrated the factor of 1.6 greater the assessment score of walking ability compared with the aged group. The young group demonstrated the factor of 1.4 greater the assessment score of muscle strength of lower limb compared with the aged group. The young group demonstrated the factor of 1.2 greater the assessment score of flexibility of ankle compared with the aged group. The results suggested that it was possible to assess the lower limb function of aged and young numerically and to advise on their foot function.

  5. Development of Structural Components of Future Technicians' Professional Competencies during Their Studies of General Disciplines in College

    ERIC Educational Resources Information Center

    Kopilov, Sergey N.; Dorozhkin, Evgenij M.; Tarasyuk, Olga V.; Osipova, Irina V.; Lazareva, Natalia V.

    2016-01-01

    The relevance of the problem stems from the necessity to develop and implement the formation model for structural components of future technicians' professional competencies during their studies of general professional disciplines. The purpose of the article is to carry out a theoretical study, to develop and approbate a model that forms the…

  6. Development of phased array techniques to improve characterization of defect located in a component of complex geometry.

    PubMed

    Mahaut, Steve; Roy, Olivier; Beroni, Claude; Rotter, Bernhard

    2002-05-01

    Ultrasonic inspection of complex geometry components has to cope with different problems: limited access of the area assumed to be insonified, beam misorientation and distortions, loss of sensitivity. Those harmful effects can lead to inspection performance degradations, especially in terms of defect detection and characterization. Phased array techniques may be used to overcome such difficulties, as they can provide an optimal mastering of the ultrasonic beam radiated through the inspected component. This paper presents some applications of phased array inspections carried out by the French Atomic Energy Commission (CEA) and the French Company of Electricity (EDF) in the framework of R&D studies. Inspections of components with varying profile (of planar and cylindrical parts, misalignment and local depression), and containing artificial reflectors have been carried out with pulse echo immersion techniques, using standard and phased arrays transducers. Optimal delay laws have been applied to preserve the beam characteristics in spite of the varying profile geometry encountered as the phased array transducer was moved over the component. Those delay laws allow to efficiently compensate the beam distortions generated by the profile geometry. They were computed using a specific model and compared to experimental delays obtained using through transmission tests. Experimental and simulation results showed that the defect detection and characterization performances were greatly enhanced using phased array techniques. In the presented examples, with standard transducers, defects located below the irregular parts of the specimen were partially detected, in accurately located or even missed, whereas phased array inspections enabled to detect and locate all of these defects.

  7. Higher Education and Development in South-East Asia. Volume III, Part 1, High-level Manpower for Development.

    ERIC Educational Resources Information Center

    Hunter, Guy

    This document, the first part of the third volume of a study concerned with the role of institutions of higher education in the development of countries in South-East Asia, appraises the high-level manpower needs of the region. The report is divided into two sections: the first includes the major comments on the position of high-level manpower in…

  8. Cross- and triple-ratios of human body parts during development.

    PubMed

    Lundh, Torbjörn; Udagawa, Jun; Hänel, Sven-Erik; Otani, Hiroki

    2011-08-01

    Recently developed landmark-based geometric morphometry has been used to depict the morphological development of organisms. In geometry, four landmarks can be mapped to any other four by Möbius transformations, if the cross-ratio of the landmarks is invariant and vice versa. To geometrically analyze the morphological development of the human body, we examined the cross-ratio of three consecutive body parts that are segmented by four landmarks in their configuration. Moreover, we introduced the triple-ratio of five landmarks that segments four consecutive parts (e.g., the shoulder, upper arm, forearm, and hand) and examined their growth patterns. The cross- and triple-ratios of the upper limb and shoulder girdle in fetuses were constant when biomechanical landmarks were used, although the cross-ratio of the upper limb varied when anatomical landmarks were used. The cross-ratios of the lower limbs, trunk, and pelvic girdles in fetuses differed from their corresponding cross-ratios in adults. These results suggest Möbius growth in the fetal upper limb and shoulder girdle but not in the other body parts examined. However, the growth balance of the three contiguous body parts was represented by the developmental change in the cross-ratio. Therefore, the cross- and triple-ratios may be applicable for simple but significant assessments of growth balance or proportion of the body parts.

  9. Ericksonian Approach to Experiential Education, Part 1: Developing the Stance of the Practitioner; Part 2: Tailoring Interventions; Part 3: Applying Specific Ericksonian Techniques.

    ERIC Educational Resources Information Center

    Itin, Christian

    This three-part workshop presentation explores the ideas of Milton Erickson on the therapeutic relationship and the therapeutic use of metaphor, and applies these ideas to experiential education and adventure therapy. Part 1 introduces the practitioner to the core philosophy within an Ericksonian approach: "utilization" of a client's…

  10. Low-melting-point titanium-base brazing alloys. Part 1: Characteristics of two-, three-, and four-component filler metals

    SciTech Connect

    Chang, E.; Chen, C.H.

    1997-12-01

    The melting point, microstructure, phase, and electrochemical behavior of Ti-21Ni-15Cu alloy, together with two-, three-, and four-component low-melting-point titanium-base brazing alloys, are presented in this paper. Five filler metals were selected for the study, in which melting points were measured by differential thermal analysis, phases identified by x-ray diffractometry, and corrosion behaviors tested by potentiodynamic polarization. The experimental results show that the three-component Ti-15Cu-15Ni and the newly developed Ti-21Ni-14Cu alloys exhibit the combination of lower melting point and superior corrosion resistance compared to the two- and four-component titanium alloys, 316L stainless steel, and a Co-Cr-Mo alloy in Hank`s solution at 37 C. On a short time basis, the presence of Ti{sub 2}Ni and Ti{sub 2}Cu intermetallics in the Ti-15Cu-15Ni and Ti-21Ni-14Cu alloys should not be preferentially dissolved in galvanic corrosion with respect to the dissimilar Ti-6Al-4V alloy.

  11. Multiphase wide gap braze alloys for the repair of nickel-base superalloy turbine components: Development and characterization

    NASA Astrophysics Data System (ADS)

    Nelson, Scott David

    Gas turbine components made of nickel-base superalloys experience cracking after service in extreme environments. As these cracks can be wide, brazing or fusion welding is typically used to repair them. Properly designed and applied, brazing filler metal will help extend the useful life of damaged turbine components. During repair of defective OEM parts, brazing is also considered, provided that proper filler metals with enhanced ductility and improved resistance to low-cycle fatigue are available. This research strives to develop the brazing technique and alloys to achieve a repair with acceptable mechanical properties. Additionally, the effects of silicon and boron, as fast diffusing and melting point suppressing elements on the braze microstructure and mechanical properties were examined in detail to help guide future alloy development. Three commercially available "low-temperature" brazing powders were mixed with an additive superalloy powder to prepare a series of filler metals for wide gap brazing used to repair OEM gas turbine components. BNi-2 (Ni-7Cr-4.2Si-3B-3Fe), BNi-5 (Ni-19Cr-10Si) and BNi-9 (Ni-15Cr-3.5B) were mixed with MARM247 (Ni-10W-10Co-8.25Cr-5.5Al-3Ta-1Ti-0.7Mo-0.5Fe-0.015B) at ratios of 40, 50, and 60 wt. pct. creating a total of nine experimental filler alloys. The brazes were applied to a 0.06 inch gap in a Rene 108(TM) substrate for mechanical and microstructural analysis. The wettability and flow of each of the experimental alloys were analyzed to determine the required brazing temperature through isothermal spreadability experiments. Bend testing was performed on brazed joints to determine their mechanical properties and maximum angular deflection. The metallurgical driving factors, such as solidification behavior and compositional effects, were analyzed to correlate the resulting microstructural constituents to the mechanical properties developed through experimentation. It was found that because of the solid solubility of silicon into

  12. Software tools for developing parallel applications. Part 1: Code development and debugging

    SciTech Connect

    Brown, J.; Geist, A.; Pancake, C.; Rover, D.

    1997-04-01

    Developing an application for parallel computers can be a lengthy and frustrating process making it a perfect candidate for software tool support. Yet application programmers are often the last to hear about new tools emerging from R and D efforts. This paper provides an overview of two focuses of tool support: code development and debugging. Each is discussed in terms of the programmer needs addressed, the extent to which representative current tools meet those needs, and what new levels of tool support are important if parallel computing is to become more widespread.

  13. Plant Biotechnology Can Enhance Food Security and Nutrition in the Developing World Part 1.

    PubMed

    Mackey, Maureen; Montgomery, Jill

    2004-03-01

    The world’s demand for food production will increase markedly in the coming years. Meeting this demand will require that we employ all manner of approaches, including the use of biotechnology, to produce results that cannot be achieved using traditional methods. This 2-part article reviews ongoing experiences in developing countries where crop biotechnology is being used to enhance the availability and/or nutritional value of local crops. In part 1, the authors describe strategies that seek to enhance yields of staples and to improve the yields of indigenous nutritious foods. In Part 2 of this article, the authors describe strategies that seek to enhance the nutrient density of foods that can increase net income to resource-poor farmers in developing countries.

  14. Canl to Curarrehue (Chile): A Journey in Alternative Development. Outdoor Education and Sustainable Development: Part Two.

    ERIC Educational Resources Information Center

    Walker, Rod

    1999-01-01

    The outdoor experience's core element of connection to the earth is a central feature of an environmental-education project in Canl forest sanctuary (Chile). Developed to provide integrated environmental and adventure-education experiences to forest visitors, the project expanded to train local youth as ecotourism guides and native-tree nursery…

  15. BIOMARKERS FOR ASSESSING REPRODUCTIVE DEVELOPMENT AND HEALTH: PART 1 - PUBERTAL DEVELOPMENT

    EPA Science Inventory

    The proposed National Children?s Study has helped raise awareness of the issues related to children?s health and the importance of monitoring the growth and development of children from preconception through to adulthood. Many genetic predispositions can adversely impact the nor...

  16. Development of remote sensing technology in New Zealand, part 1. Mapping land use and environmental studies in New Zealand, part 2. Indigenous forest assessment, part 3. Seismotectonic, structural, volcanologic and geomorphic study of New Zealand, part 4

    NASA Technical Reports Server (NTRS)

    Probine, M. C.; Suggate, R. P.; Stirling, I. F.; Mcgreevy, M. G. (Principal Investigator)

    1976-01-01

    The author has identified the following significant results. As part of the tape reformatting process, a simple coded picture output program was developed. This represents Pixel's radiance level by one of a 47 character set on a nonoverprinting line printer. It not only has aided in locating areas for the reformatting process, but has also formed the foundation for a supervised clustering package. This in turn has led to a simplistic but effective thematic mapping package.

  17. Part-Time Work of High School Students: Impact on Employability, Employment Outcomes and Career Development

    ERIC Educational Resources Information Center

    Patton, Wendy; Smith, Erica

    2010-01-01

    With the large number of high school students engaging in part-time work, very little is known about the impact of this activity on employability, employment outcomes and career development. This paper outlines the context of this phenomenon in Australia, and reviews the body of empirical work that has been published in recent years, noting the…

  18. "Scaffolding" of Action Learning within a Part-Time Management Development Module

    ERIC Educational Resources Information Center

    Joesbury, Mark

    2015-01-01

    This Account of Practice describes the introduction and development of action learning within a level 5 module of "Communications at Work" delivered as part of a Business & Technology Education Council (BTEC) Professional Certificate in Management (CMS) between 2005/2006 and 2009/2010. This will commence with a personal narrative and…

  19. Part Two: Graduate Student Perspectives on the Development of Electronic Portfolios

    ERIC Educational Resources Information Center

    Tsai, Howard; Lowell, Kay; Liu, Peilin; MacDonald, Laurie; Lohr, Linda

    2004-01-01

    This is the second segment of a two-part investigation into the design of electronic portfolios in a graduate-level educational technology class that had been structured around the ADDIE model of instructional design. This second paper is a reflective case study of how students implemented the ADDIE model--Analyze, Design, Develop, Implement,…

  20. Reflective Blogging as Part of ICT Professional Development to Support Pedagogical Change

    ERIC Educational Resources Information Center

    Prestridge, Sarah J.

    2014-01-01

    Reflection is considered an inherent part of teacher practice. However, when used within professional development activity, it is fraught with issues associated with teacher confidence and skill in reflective action. Coupled with anxiety generally associated with technological competency and understanding the nature of blogging, constructive…

  1. Handbook for Directing Teachers. Developed as a Part of the Teacher Education Internship Project.

    ERIC Educational Resources Information Center

    Terrell, Mary Sue; Grimes, Mary

    This handbook is part of a series of guides developed for use with the Teacher Education Internship Project at the University of North Florida. This guide is written for directing teachers who work with the teacher interns during the practice teaching experience. Sections of the handbook discuss: (1) the clinical supervision model used by the…

  2. Peer Coaching as Part of a Professional Development Program for Science Teachers in Botswana

    ERIC Educational Resources Information Center

    Thijs, Annette; van den Berg, Ellen

    2002-01-01

    This paper discusses the findings of a study into the potentials of peer coaching as part of a professional development program, consisting of an in-service course and exemplary curriculum materials, in supporting the implementation of learner-centred teaching in senior secondary science and mathematics education in Botswana. Teachers in the study…

  3. Practitioner Research as Part of Professional Development in Initial Teacher Education

    ERIC Educational Resources Information Center

    Maaranen, Katriina

    2009-01-01

    The purpose of this research is to seek the connection between professional development and an MA thesis research project, which is conducted as part of initial teacher education in Finland. This article examines the experiences of teachers with work experience, but without an official qualification, who recently completed their MA thesis. The…

  4. Mapping the Journey: Developing an Information Literacy Strategy as Part of Curriculum Reform

    ERIC Educational Resources Information Center

    Salisbury, Fiona; Sheridan, Linda

    2011-01-01

    This article will outline the development of an Information Literacy Strategy in 2009 as part of an overall program of curriculum review and renewal at La Trobe University, Australia. Current information literacy programs at La Trobe University Library employ a diverse range of approaches and delivery methods. However, they are limited in scope…

  5. Electronics and telecommunications in Poland, issues and perspectives: Part III. Innovativeness, applications, economy, development scenarios, politics

    NASA Astrophysics Data System (ADS)

    Modelski, Józef; Romaniuk, Ryszard

    2010-09-01

    Electronics is under development in this country in an organized and institutional way since the beginning of 30-ties of the previous century. It grew up from electrical engineering of weak currents and its first name used popularly was communications. It was time when television was born and the radio was maturing. Electronics is a branch of research and technology which deals with generation and processing of electrical and electromagnetic signals. A subject of telecommunications is signal transmission for a distance. Electronics and telecommunications (ET) includes or is combined with other branches like: microelectronics, radioelectronics, optoelectronics, photonics, acoustoelectronics, magnetronics, bioelectronics, energoelectronics, material engineering, semiconductor physics, automation and robotics, mechatronics and microsystems, informatics, teleinformatics, software engineering and other. Devices and functional systems of ET such as computers, data warehouses, cell phones, TV sets, Internet, GPS are build of electronic components and circuits. ET is a branch which belongs to hi-tech area, where the products gather a large load of knowledge of value overcoming frequently the price of work and material. ET has recently turned to an active participant of the processes of generation, storing, processing, transportation, distribution and usage of knowledge in the society. ET started to create artificial intelligence, co-creates intellectual property, searches for knowledge in big data sets, aids medicine, extends virtual/augmented reality, builds Internet of persons and things, strengthens security, protects natural environment, facilitates our life, aids our decisions, activates individuals, equalizes chances, provides convenient personal communications and access to data, starts building a penetrating ubiquitous infrastructure, ceases to be only a branch of technology, grows into the social space, touches culture, sociology, psychology and art. Such an

  6. Electronics and telecommunications in Poland, issues and perspectives: Part II. Science, research, development, higher education

    NASA Astrophysics Data System (ADS)

    Modelski, Józef; Romaniuk, Ryszard

    2010-09-01

    Electronics is under development in this country in an organized and institutional way since the beginning of 30-ties of the previous century. It grew up from electrical engineering of weak currents and its first name used popularly was communications. It was time when television was born and the radio was maturing. Electronics is a branch of research and technology which deals with generation and processing of electrical and electromagnetic signals. A subject of telecommunications is signal transmission for a distance. Electronics and telecommunications (ET) includes or is combined with other branches like: microelectronics, radioelectronics, optoelectronics, photonics, acoustoelectronics, magnetronics, bioelectronics, energoelectronics, material engineering, semiconductor physics, automation and robotics, mechatronics and microsystems, informatics, teleinformatics, software engineering and other. Devices and functional systems of ET such as computers, data warehouses, cell phones, TV sets, Internet, GPS are build of electronic components and circuits. ET is a branch which belongs to hi-tech area, where the products gather a large load of knowledge of value overcoming frequently the price of work and material. ET has recently turned to an active participant of the processes of generation, storing, processing, transportation, distribution and usage of knowledge in the society. ET started to create artificial intelligence, co-creates intellectual property, searches for knowledge in big data sets, aids medicine, extends virtual/augmented reality, builds Internet of persons and things, strengthens security, protects natural environment, facilitates our life, aids our decisions, activates individuals, equalizes chances, provides convenient personal communications and access to data, starts building a penetrating ubiquitous infrastructure, ceases to be only a branch of technology, grows into the social space, touches culture, sociology, psychology and art. Such an

  7. A formative model for student nurse development and evaluation--Part 1--Developing the model.

    PubMed

    van der Merwe, A S; Roos, E C; Mulder, M; Joubert, A; Botha, D E; Coetzee, M H; Lombard, A; van Niekerk, A; Visser, L

    1996-12-01

    Preparing student nurses for the profession is a complex task for nurse educators; especially when dealing with the development of personal and interpersonal skills, qualities and values held in high esteem by the nursing profession and the community they serve. These researchers developed a model for formative evaluation of students by using the principles of inductive and deductive reasoning. This model was implemented in clinical practice situations and evaluated for its usefulness. It seems that the model enhanced the standards of nursing care because it had a positive effect on the behavior of students and they were better motivated; the model also improved interpersonal relationships and communication between practising nurses and students. The fact that students repeatedly use the model as a norm for self evaluation ensures that they are constantly reminded of the standards required of a professional nurse.

  8. Minor components in the sex pheromone of legume podborer: Maruca vitrata development of an attractive blend.

    PubMed

    Downham, M C A; Hall, D R; Chamberlain, D J; Cork, A; Farman, D I; Tamò, M; Dahounto, D; Datinon, B; Adetonah, S

    2003-04-01

    The legume podborer, Maruca vitrata (syn. M. testulalis) (F.) (Lepidoptera: Pyralidae) is a pantropical pest of legume crops. Sex pheromone was collected by gland extraction or trapping of volatiles from virgin female moths originating in India, West Africa, or Taiwan. Analysis by GC-EAG and GC-MS confirmed previously published findings that (E,E)-10,12-hexadecadienal is the most abundant EAG-active component with 2-5% of (E,E)-10,12-hexadecadienol also present. At least one other EAG response was detected at retention times typical of monounsaturated hexadecenals or tetradecenyl acetates, but neither could be detected by GC-MS. Laboratory wind-tunnel bioassays and a field bioassay of blends of (E,E)-10,12-hexadecadienal with (E,E )-10,12-hexadecadienol and a range of monounsaturated hexadecenal and tetradecenyl acetate isomers indicated greatest attraction of males was to those including (E,E)-10,12-hexadecadienol and (E)-10-hexadecenal as minor components. In subsequent trapping experiments in cowpea fields in Benin, traps baited with a three-component blend of (E,E)-10,12-hexadecadienal and these two minor components in a 100:5:5 ratio caught significantly more males than traps baited with the major component alone, either two-component blend, or virgin female moths. Further blend optimization experiments did not produce a more attractive blend. No significant differences in catches were found between traps baited with polyethylene vials or rubber septa, or between lures containing 0.01 and 0.1 mg of synthetic pheromone. Significant numbers of female M. vitrata moths, up to 50% of total catches, were trapped with synthetic blends but not with virgin females. At present there is no clear explanation for this almost unprecedented finding, but the phenomenon may improve the predictive power of traps for population monitoring.

  9. Making mental health an integral part of sustainable development: the contribution of a social determinants framework.

    PubMed

    De Silva, M J

    2015-04-01

    There have been repeated calls to include mental health in the sustainable development goals (SDGs), arguing that progress in development will not be made without improvements in mental health. Although these calls are starting to gain political traction, currently only a tiny fraction of international development work includes mental health. A social determinants framework may be useful in incorporating mental health into sustainable development because it promotes a multi-sectorial and multi-disciplinary approach which is the corner stone of good development practice. Two approaches are suggested to make mental health a part of sustainable development: (1) integrate mental health into existing development programmes to promote social and economic environments that prevent mental health problems developing; (2) ensure that mental health programmes are better at promoting sustainable development by preventing the negative social and economic consequences of mental illness. Real-world examples of these approaches are provided. To achieve this, the mental health impact of wider development programmes, and the social and economic consequences of mental health interventions, must be evaluated. Development agencies should ensure that they have equity for mental health in all their policies, and investment must be increased for those mental health prevention, promotion and treatment programmes which have the greatest impact on sustainable development. The SDGs bring the promise of a more holistic approach to development. It is now the task of global mental health to demonstrate not just that mental health is an integral part of sustainable development, but that affordable and effective solutions exist which can improve mental health and development more broadly.

  10. [Lasers in dentistry. Part A--Development, characteristics, structure, principles of operation and types of lasers].

    PubMed

    Stabholz, A; Stabholz, A; Leopold, Y; Rosenberg, Y; Moshonov, J

    2001-04-01

    Laser technology is developing very quickly. New Lasers with a wide range of characteristics are available today and are being used in the various fields of dentistry. The search for new devices and technologies for dental procedures was always challenging and in the last two decades much experience and knowledge has been gained. The purpose of this series of articles published in the journal of the Israel Dental Association in three parts is to present the Israeli dentist a comprehensive and contemporary overview which will assist him in understanding the potential of the use of laser technology for clinical applications in dentistry. The first part will describe the history and development of lasers in dentistry, the characteristics and structure of lasers as well as their principles of operation. A description of the different types of lasers used today in dentistry will be presented in the first part. The second part will describe the interaction of lasers with biological tissues and their effect on the soft and hard tissues of the oral cavity as well as on the dental pulp. Laser safety in the dental practice will also be discussed. The third part will focus on clinical applications of Lasers in Dentistry: pits and fissures sealing, dentin desensitization, cavity preparations, composite curing, surgical procedures and tooth whitening. Current status of using lasers in periodontics, endodontics and dental implantology will be discussed and possible future clinical applications of lasers in dentistry will be presented.

  11. Y-12 development organization technical progress report, Part 3: Metal processing period ending March 1, 1995

    SciTech Connect

    Northcutt, W.G. Jr.

    1995-10-01

    In an effort to integrate vertically the manufacturing processes at the Oak Ridge Centers for Manufacturing Technology (ORCMT) and at the same time obtain higher quality nickel-aluminium-bronze castings more quickly than outside sources were providing, a development program was started, addressing the problems of castings these types of components. Several small demonstration castings were made under vacuum and in graphite to assess the quality achievable by using this system.

  12. Robust integration schemes for generalized viscoplasticity with internal-state variables. Part 1: Theoretical developments and applications

    NASA Technical Reports Server (NTRS)

    Saleeb, Atef F.; Li, Wei

    1995-01-01

    This two-part report is concerned with the development of a general framework for the implicit time-stepping integrators for the flow and evolution equations in generalized viscoplastic models. The primary goal is to present a complete theoretical formulation, and to address in detail the algorithmic and numerical analysis aspects involved in its finite element implementation, as well as to critically assess the numerical performance of the developed schemes in a comprehensive set of test cases. On the theoretical side, the general framework is developed on the basis of the unconditionally-stable, backward-Euler difference scheme as a starting point. Its mathematical structure is of sufficient generality to allow a unified treatment of different classes of viscoplastic models with internal variables. In particular, two specific models of this type, which are representative of the present start-of-art in metal viscoplasticity, are considered in applications reported here; i.e., fully associative (GVIPS) and non-associative (NAV) models. The matrix forms developed for both these models are directly applicable for both initially isotropic and anisotropic materials, in general (three-dimensional) situations as well as subspace applications (i.e., plane stress/strain, axisymmetric, generalized plane stress in shells). On the computational side, issues related to efficiency and robustness are emphasized in developing the (local) interative algorithm. In particular, closed-form expressions for residual vectors and (consistent) material tangent stiffness arrays are given explicitly for both GVIPS and NAV models, with their maximum sizes 'optimized' to depend only on the number of independent stress components (but independent of the number of viscoplastic internal state parameters). Significant robustness of the local iterative solution is provided by complementing the basic Newton-Raphson scheme with a line-search strategy for convergence. In the present first part of the

  13. The historical development and nutritional importance of olive and olive oil constituted an important part of the Mediterranean diet.

    PubMed

    Uylaşer, Vildan; Yildiz, Gökçen

    2014-01-01

    The olive tree (Olea europaea) is widely cultivated for the production of both oil and table olives and very significant because of its economic value. Olive and olive oil, a traditional food product with thousands of years of history, are the essential components of the Mediterranean diet and are largely consumed in the world. Beside of their economical contribution to national economy, these are an important food in terms of their nutritional value. Olive and olive oil may have a role in the prevention of coronary heart disease and certain cancers because of their high levels of monosaturated fatty acids and phenolic compounds. In addition, olives (Olea europaea L.) and olive oils provide a rich source of natural antioxidants. These make them both fairly stable against auto-oxidation and suitable for human health. The aim of this paper is to define the historical development and nutritional importance of olive and olive oil constituted an important part of the Mediterranean diet.

  14. Thermal stress analysis of fused-cast AZS refractories during production; Part 2: Development of thermo-elastic stress model

    SciTech Connect

    Cockcroft, S.L.; Brimacombe, J.K. . Centre for Metallurgical Process Engineering); Walrod, D.G.; Myles, T.A. . Monofrax-S Plant)

    1994-06-01

    Mathematical models of heat flow and thermo-elastic stress, based on the finite-element method, have been developed and utilized to analyze the voidless,'' fused-cast, AZS, solidification process. The results of the mathematical analysis, in conjunction with information obtained in a comprehensive industrial study, presented in Part 1 of this paper, describe the mechanisms for the formation of the various crack types found in the fused-cast product. Thermal stresses are generated early in the solidification process by rapid cooling of the refractory surface as it contacts the initially cool mold and later in conjunction with the tetragonal-to-monoclinic phase transformation which occurs in the zirconia component of the AZS refractory. Applying this model, castings were made using a revised mold design. Preliminary results indicate these castings to be free of objectionable transverse cracks.

  15. Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1996--September 30, 1997

    SciTech Connect

    Gibson, J.

    1998-03-01

    This report documents the technical activities of the period October 1, 1996 through September 30, 1997. During this period, GA and their partner Schafer Corporation were assigned 13 formal tasks in support of the ICF program and its five laboratories. A portion of the effort on these tasks included providing direct {open_quotes}Onsite Support{close_quotes} at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). Over 700 gold-plated hohlraum mandrels were fabricated and delivered to LLNL, LANL and SNLA. More than 1600 glass and plastic target capsules were produced for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). Nearly 2000 various target foils and films were delivered for Naval Research Lab (NRL) and UR/LLE in FY97. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. This project is part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. During FY97, significant progress was made in the design and component testing of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA. This included major design changes, reduction in equipment, and process simplifications. This report summarizes and documents the technical progress made on these tasks.

  16. Rapid Naming Speed Components and Reading Development in a Consistent Orthography

    ERIC Educational Resources Information Center

    Georgiou, George K.; Papadopoulos, Timothy C.; Fella, Argyro; Parrila, Rauno

    2012-01-01

    We examined how rapid automatized naming (RAN) components--articulation time and pause time--predict word and text reading fluency in a consistent orthography (Greek). In total, 68 children were followed from Grade 2 to Grade 6 and were assessed three times on RAN (Digits and Objects), phonological awareness, orthographic processing, speed of…

  17. Study and program plan for improved heavy duty gas turbine engine ceramic component development

    NASA Technical Reports Server (NTRS)

    Helms, H. E.

    1977-01-01

    Fuel economy in a commercially viable gas turbine engine was demonstrated through use of ceramic materials. Study results show that increased turbine inlet and generator inlet temperatures, through the use of ceramic materials, contribute the greatest amount to achieving fuel economy goals. Improved component efficiencies show significant additional gains in fuel economy.

  18. A lean methane premixed laminar flame doped with components of diesel fuel part III: Indane and comparison between n-butylbenzene, n-propylcyclohexane and indane

    SciTech Connect

    Pousse, E.; Tian, Z.Y.; Glaude, P.A.; Fournet, R.; Battin-Leclerc, F.

    2010-07-15

    To better understand the chemistry of the combustion of components of diesel fuel, the structure of a laminar lean premixed methane flame doped with indane has been investigated. The inlet gases contained 7.1% (molar) of methane, 36.8% of oxygen and 0.9% of indane corresponding to an equivalence ratio of 0.67 and a ratio C{sub 10}H{sub 14}/CH{sub 4} of 12.8%. The flame has been stabilized on a burner at a pressure of 6.7 kPa (50 Torr) using argon as diluent, with a gas velocity at the burner of 49.1 cm s{sup -1} at 333 K. Quantified species included the usual methane C{sub 0}-C{sub 2} combustion products, but also 16 C{sub 3}-C{sub 5} non-aromatic hydrocarbons, 6 C{sub 1}-C{sub 3} non-aromatic oxygenated compounds, as well as 22 aromatic products, namely benzene, toluene, xylenes, phenylacetylene, ethylbenzene, styrene, propenylbenzene, allylbenzene, n-propylbenzene, methylstyrenes, ethyltoluenes, trimethylbenzenes, n-butylbenzene, dimethylethylbenzene, indene, methylindenes, methylindane, benzocyclobutene, naphthalene, phenol, benzaldehyde, and benzofuran. A new mechanism for the oxidation of indane was proposed whose predictions were in satisfactory agreement with measured species profiles in both flames and jet-stirred reactor experiments. The main reaction pathways of consumption of indane have been derived from flow rate analyses in the two types of reactors. A comparison of the effect of the addition of three components of diesel fuel, namely indane, n-butylbenzene and n-propylcyclohexane (parts I and II of this series of paper), on the structure of a laminar lean premixed methane flame is also presented. (author)

  19. Development of a New and Fast Linear Solver for Multi-component Reactive Transport Simulation

    NASA Astrophysics Data System (ADS)

    Qiao, C.; Li, L.; Bao, C.; Hu, X.; Johns, R.; Xu, J.

    2013-12-01

    Reactive transport models (RTM) have been extensively used to understand the coupling between solute transport and (bio) geochemical reactions in complex earth systems. RTM typically involves a large number of primary and secondary species with a complex reaction network in large domains. The computational expenses increase significantly with the number of grid blocks and the number of chemical species. Within both the operator splitting approach (OS) and the global implicit approach (GI) that are commonly used, the steps that involve Newton-Raphson method are typically one of the most time-consuming parts (up to 80% to 90% of CPU times). Under such circumstances, accelerating reactive transport simulation is very essential. In this research, we present a physics-based linear system solution strategy for general reactive transport models with many species. We observed up to five times speed up for the linear solver portion of the simulations in our test cases. Our new linear solver takes advantage of the sparsity of the Jacobian matrix arising from the reaction network. The Jacobian matrix for the speciation problem is typically considered as a dense matrix and solved with a direct method such as Gaussian elimination. For the reactive transport problem, the graph of the local Jacobian matrix has a one-to-one correspondence to the reaction network graph. The Jacobian matrix is commonly sparse and has the same sparsity structure for the same reaction network. We developed a strategy that performs a minimum degree of reordering and symbolic factorization to determine the non-zero pattern at the beginning of the OS and GI simulation. During the speciation calculation in OS, we calculate the L and U factors and solve the triangular matrices according to the non-zero pattern. For GI, our strategy can be applied to inverse the diagonal blocks in the block-Jacobi preconditioner and smoothers of the multigrid preconditioners in iterative solvers. Our strategy is naturally

  20. Development of radiation tolerant components for the Quench Protection System at CERN

    NASA Astrophysics Data System (ADS)

    Bitterling, O.; Denz, R.; Steckert, J.; Uznanski, S.

    2016-01-01

    This paper describes the results of irradiation campaigns with the high resolution Analog to Digital Converter (ADC) ADS1281. This ADC will be used as part of a revised quench detection circuit for the 600 A corrector magnets at the CERN Large Hadron Collider (LHC) . To verify the radiation tolerance of the ADC an irradiation campaign using a proton beam, applying doses up to 3,4 kGy was conducted. The resulting data and an analysis of the found failure modes is discussed in this paper. Several mitigation measures are described that allow to reduce the error rate to levels acceptable for operation as part of the LHC QPS.

  1. Development of an enhanced anticaries efficacy dual component dentifrice containing sodium fluoride and dicalcium phosphate dihydrate.

    PubMed

    Sullivan, R J; Masters, J; Cantore, R; Roberson, A; Petrou, I; Stranick, M; Goldman, H; Guggenheim, B; Gaffar, A

    2001-05-01

    A dual-chamber dentifrice, which contains sodium fluoride (NaF) in one component and dicalcium phosphate dihydrate (dical) in the other, has been developed. The dentifrice is packaged in a dual-chamber tube and is formulated to deliver 1100 ppm F. A series of studies consisting of in vitro fluoride uptake, in vivo calcium labeling, intraoral remineralization-demineralization, and animal caries studies were performed to support the improved anticaries efficacy of this product in comparison to a sodium fluoride/silica dentifrice (NaF/silica). An in vitro fluoride uptake study comparing 1100 ppm F NaF/dical dentifrice to 1100 ppm F NaF/silica showed that NaF/dical delivered significantly more fluoride than NaF/silica, 3.72 +/- 0.36 micrograms/cm2 versus 2.41 +/- 0.10 micrograms/cm2. A 6-day in vivo brushing study with a 44Ca labeled NaF/dical dentifrice showed that calcium from dical penetrated demineralized enamel and was present in plaque up to 18 hrs since the last brushing. An intra-oral remineralization-demineralization study was performed to evaluate NaF/dical's ability to promote remineralization in comparison to three silica-based dentifrices containing 0, 250, and 1100 ppm F as NaF. The percent mineral changes after treatment were +20.44 +/- 17.14 for NaF/dical, +9.27 +/- 19.53 for 1100 ppm NaF/silica, -1.43 +/- 20.57 for 250 ppm NaF/silica, and -12.36 +/- 32.76 for 0 ppm F/silica. A statistical analysis showed that the dual-chamber NaF/dical dentifrice was significantly more effective than the 1100 ppm NaF/silica dentifrice at promoting remineralization. A rat caries study was performed to evaluate NaF/dical ability to prevent caries in comparison to 1100 ppm F NaF/silica, 250 ppm F NaF/silica, silica, and dical dentifrices. The mean smooth surface caries scores were 1.6 +/- 2.8 for NaF/dical, 5.5 +/- 6.2 for 1100 ppm F NaF/silica, 10.6 +/- 6.2 for 250 ppm F NaF/silica, 13.7 +/- 4.7 for 0 ppm F/silica, and 9.5 +/- 7.8 0 ppm F/dical. A statistical analysis

  2. Utilizing the CIPP Model as a Means to Develop an Integrated Service-Learning Component in a University Health Course

    ERIC Educational Resources Information Center

    Powell, Brent; Conrad, Eric

    2015-01-01

    Purpose: To examine the enhancement of a university health course through the utilization of the CIPP Model as a means to develop an integrated service-learning component. Methods: The CIPP model was utilized in two concurrent semesters of an undergraduate health course in order to design and evaluate the implementation of a drug and alcohol…

  3. Development and Implementation of a Program of Evaluation To Support Improvement of Organizational Components in a Child Care Center.

    ERIC Educational Resources Information Center

    Cross, Alice Frazeur

    This practicum's goal was to improve the organizational components of a university child care center through the development and implementation of a comprehensive program of evaluation. Several evaluation models were considered. The Context-Input-Process-Product Model was selected for its flexibility in providing formative and summative results,…

  4. Research Gaps and Technology Needs in Development of PHM for Passive AdvSMR Components

    SciTech Connect

    Meyer, Ryan M.; Ramuhalli, Pradeep; Coble, Jamie B.; Hirt, Evelyn H.; Mitchell, Mark R.; Wootan, David W.; Berglin, Eric J.; Bond, Leonard J.; Henager, Charles H.

    2014-01-01

    Advanced small modular reactors (AdvSMRs), which are based on modularization of advanced reactor concepts, may provide a longer-term alternative to traditional light-water reactors and near term small modular reactors (SMRs), which are based on integral pressurized water reactor (iPWR) concepts. SMRs are challenged economically due to losses in economy of scale, thus, there is increased motivation to reduce the controllable operations and maintenance (O&M) costs through automation technologies including prognostics health management (PHM) systems. In this regard, PHM systems have the potential to play a vital role in supporting the deployment of AdvSMRs and face several unique challenges with respect to implementation for passive AdvSMR components. This paper presents a summary of a research gaps and technical needs assessment performed for implementation of PHM for passive AdvSMR components. state-of-the-art in PHM.

  5. Research gaps and technology needs in development of PHM for passive AdvSMR components

    SciTech Connect

    Meyer, Ryan M.; Ramuhalli, Pradeep; Hirt, Evelyn H.; Mitchell, Mark R.; Wootan, David W.; Berglin, Eric J.; Henagar, Chuck H. Jr.; Coble, Jamie B.; Bond, Leonard J.

    2014-02-18

    Advanced small modular reactors (AdvSMRs), which are based on modularization of advanced reactor concepts, may provide a longer-term alternative to traditional light-water reactors and near-term small modular reactors (SMRs), which are based on integral pressurized water reactor (iPWR) concepts. SMRs are challenged economically because of losses in economy of scale; thus, there is increased motivation to reduce the controllable operations and maintenance costs through automation technologies including prognostics health management (PHM) systems. In this regard, PHM systems have the potential to play a vital role in supporting the deployment of AdvSMRs and face several unique challenges with respect to implementation for passive AdvSMR components. This paper presents a summary of a research gaps and technical needs assessment performed for implementation of PHM for passive AdvSMR components.

  6. The development and testing of ceramic components in piston engines. Final report

    SciTech Connect

    McEntire, B.J.; Willis, R.W.; Southam, R.E.

    1994-10-01

    Within the past 10--15 years, ceramic hardware has been fabricated and tested in a number of piston engine applications including valves, piston pins, roller followers, tappet shims, and other wear components. It has been shown that, with proper design and installation, ceramics improve performance, fuel economy, and wear and corrosion resistance. These results have been obtained using rig and road tests on both stock and race engines. Selected summaries of these tests are presented in this review paper.

  7. Adiabatic diesel engine component development: Reference engine for on-highway applications

    NASA Technical Reports Server (NTRS)

    Hakim, Nabil S.

    1986-01-01

    The main objectives were to select an advanced low heat rejection diesel reference engine (ADRE) and to carry out systems analysis and design. The ADRE concept selection consisted of: (1) rated point performance optimization; (2) study of various exhaust energy recovery scenarios; (3) components, systems and engine configuration studies; and (4) life cycle cost estimates of the ADRE economic worth. The resulting ADRE design proposed a reciprocator with many advanced features for the 1995 technology demonstration time frame. These included ceramic air gap insulated hot section structural components, high temperature tribology treatments, nonmechanical (camless) valve actuation systems, and elimination of the cylinder head gasket. ADRE system analysis and design resulted in more definition of the engine systems. These systems include: (1) electro-hydraulic valve actuation, (2) electronic common rail injection system; (3) engine electronic control; (4) power transfer for accessory drives and exhaust energy recovery systems; and (5) truck installation. Tribology and performance assessments were also carried out. Finite element and probability of survival analyses were undertaken for the ceramic low heat rejection component.

  8. Development of an ASPEN PLUS physical property database for biofuels components

    SciTech Connect

    Wooley, R.J.; Putsche, V.

    1996-04-01

    Physical property data for many of the key components used in the simulation for the ethanol from lignocellulose process are not available in the standard ASPEN PLUS property databases. Indeed, many of the properties necessary to successfully simulate this process are not available anywhere. In addition, inputting the available properties into each simulation is awkward and tedious, and mistakes can be easily introduced when a long list of physical property equation parameters is entered. Therefore, one must evaluate the literature, estimate properties where necessary, and determine a set of consistent physical properties for all components of interest. The components must then be entered into an in-house NREL ASPEN PLUS database so they can be called on without being retyped into each specific simulation. The first phase of this work is complete. A complete set of properties for the currently identifiable important compounds in the ethanol process is attached. With this as the starting base the authors can continue to search for and evaluate new properties or have properties measured in the laboratory and update the central database.

  9. Development of a non-invasive diagnostic technique for acetabular component loosening in total hip replacements.

    PubMed

    Alshuhri, Abdullah A; Holsgrove, Timothy P; Miles, Anthony W; Cunningham, James L

    2015-08-01

    Current techniques for diagnosing early loosening of a total hip replacement (THR) are ineffective, especially for the acetabular component. Accordingly, new, accurate, and quantifiable methods are required. The aim of this study was to investigate the viability of vibrational analysis for accurately detecting acetabular component loosening. A simplified acetabular model was constructed using a Sawbones(®) foam block. By placing a thin silicone layer between the acetabular component and the Sawbones block, 2- and 4-mm soft tissue membranes were simulated representing different loosening scenarios. A constant amplitude sinusoidal excitation with a sweep range of 100-1500 Hz was used. Output vibration from the model was measured using an accelerometer and an ultrasound probe. Loosening was determined from output signal features such as the number and relative strength of observed harmonic frequencies. Both measurement methods were sufficient to measure the output vibration. Vibrational analysis reliably detected loosening corresponding to both 2 and 4 mm tissue membranes at driving frequencies between 100 and 1000 Hz (p < 0.01) using the accelerometer. In contrast, ultrasound detected 2-mm loosening at a frequency range of 850-1050 Hz (p < 0.01) and 4-mm loosening at 500-950 Hz (p < 0.01).

  10. The Impact of Professional Development on the Quality of the Transition Components of IEPs

    ERIC Educational Resources Information Center

    Flannery, K. Brigid; Lombardi, Allison; Kato, Mimi McGrath

    2015-01-01

    Under the Individuals With Disabilities Education Act (IDEA), transition needs and services are to be discussed as part of the Individual Education Program (IEP) planning process, and decisions based on students' future goals are to be documented in the IEP. These transition requirements were included in IDEA in order to plan with the student,…

  11. Assessment of the components of the Kalimantan and Sulawesi power development project: Volume 2. Export trade information

    SciTech Connect

    1998-03-31

    This report, conducted by Utility Consulting was funded by the US Trade and Development Agency. The report concerns a power development project on the islands of Kalimantan and Sulawesi. This is TDA Volume 2, the main text (Report Volume 1), and it includes the following: (1) Introduction; (2) Transmission line and substation investment plan; (3) The distribution component; (4) Telecommunications; (5) PLN information systems; and Appendix: Figures and tables.

  12. Mass-specific optical absorption coefficients and imaginary part of the complex refractive indices of mineral dust components measured by a multi-wavelength photoacoustic spectrometer

    NASA Astrophysics Data System (ADS)

    Utry, N.; Ajtai, T.; Pintér, M.; Tombácz, E.; Illés, E.; Bozóki, Z.; Szabó, G.

    2015-01-01

    Mass-specific optical absorption coefficients (MACs) and the imaginary part (κ) of the refractive indices of various mineral dust components including silicate clays (illite, kaolin and bentonite), oxides (quartz, hematite and rutile), and carbonate (limestone) were determined at the wavelengths of 1064, 532, 355 and 266 nm. The MAC values were calculated from aerosol optical absorption coefficients measured by a multi-wavelength photoacoustic (PA) instrument, the mass concentration and the number size distribution of the generated aerosol samples as well as the size transfer functions of the measuring instruments. Values of κ were calculated from the measured and particle-loss-corrected data by using a Mie-theory-based retrieval algorithm. The determined values could be used for comparisons with calculated wavelength-dependent κ values typically deduced from bulk-phase measurements by using indirect measurement methods. Accordingly, the presented comparison of the measured and calculated aerosol optical absorption spectra revealed the strong need for standardized sample preparation and measurement methodology in case of bulk-phase measurements.

  13. Structural CNT Composites. Part I; Developing a Carbon Nanotube Filament Winder

    NASA Technical Reports Server (NTRS)

    Sauti, Godfrey; Kim, Jae-Woo; Wincheski, Russell A.; Antczak, Andrew; Campero, Jamie C.; Luong, Hoa H.; Shanahan, Michelle H.; Stelter, Christopher J.; Siochi, Emilie J.

    2015-01-01

    Carbon nanotube (CNT) based materials promise advances in the production of high strength and multifunctional components for aerospace and other applications. Specifically, in tension dominated applications, the latest CNT based filaments are yielding composite properties comparable to or exceeding composites from more established fibers such as Kevlar and carbon fiber. However, for the properties of these materials to be fully realized at the component level, suitable manufacturing processes have to be developed. These materials handle differently from conventional fibers, with different wetting characteristics and behavior under load. The limited availability of bulk forms also requires that the equipment be scaled down accordingly to tailor the process development approach to material availability. Here, the development of hardware and software for filament winding of carbon nanotube based tapes and yarns is described. This hardware features precision guidance of the CNT material and control of the winding tension over a wide range in an open architecture that allows for effective process control and troubleshooting during winding. Use of the filament winder to develop CNT based Composite Overwrapped Pressure Vessels (COPVs) shall also be discussed.

  14. Aerodynamic design and analysis system for supersonic aircraft. Part 1: General description and theoretical development

    NASA Technical Reports Server (NTRS)

    Middleton, W. D.; Lundry, J. L.

    1975-01-01

    An integrated system of computer programs has been developed for the design and analysis of supersonic configurations. The system uses linearized theory methods for the calculation of surface pressures and supersonic area rule concepts in combination with linearized theory for calculation of aerodynamic force coefficients. Interactive graphics are optional at the user's request. This part presents a general description of the system and describes the theoretical methods used.

  15. A Component Approach to Collaborative Scientific Software Development: Tools and Techniques Utilized by the Quantum Chemistry Science Application Partnership

    DOE PAGES

    Kenny, Joseph P.; Janssen, Curtis L.; Gordon, Mark S.; ...

    2008-01-01

    Cutting-edge scientific computing software is complex, increasingly involving the coupling of multiple packages to combine advanced algorithms or simulations at multiple physical scales. Component-based software engineering (CBSE) has been advanced as a technique for managing this complexity, and complex component applications have been created in the quantum chemistry domain, as well as several other simulation areas, using the component model advocated by the Common Component Architecture (CCA) Forum. While programming models do indeed enable sound software engineering practices, the selection of programming model is just one building block in a comprehensive approach to large-scale collaborative development which must also addressmore » interface and data standardization, and language and package interoperability. We provide an overview of the development approach utilized within the Quantum Chemistry Science Application Partnership, identifying design challenges, describing the techniques which we have adopted to address these challenges and highlighting the advantages which the CCA approach offers for collaborative development.« less

  16. Dynamic in-plane potential gradients for actively controlling electrochemical reactions: Part I. Characterization of 1- and 2-component alkanethiol monolayer gradients on thin gold films. Part II. Applications of in-plane potential gradients

    NASA Astrophysics Data System (ADS)

    Balss, Karin Maria

    The research contained in this thesis is focused on the formation and characterization of surface composition gradients on thin gold films that are formed by applications of in-plane potential gradients. Injecting milliamp currents into thin Au films yields significant in-plane voltage drops so that, rather than assuming a single value of potential, an in-plane potential gradient is imposed on the film which depends on the resistivity of the film, the cross sectional area and the magnitude of the potential drop. Furthermore, the in-plane electric potential gradient means that, relative to a solution reference couple, electrochemical reactions occurs at defined spatial positions corresponding to the local potential, V(x) ˜ E0. The spatial gradient in electrochemical potential can then produce spatially dependent electrochemistry. Surface-chemical potential gradients can be prepared by arranging the spread of potentials to span an electrochemical wave mediating redox-associated adsorption or desorption. Examples of reactions that can be spatially patterned include the electrosorption of alkanethiols and over-potential metal deposition. The unique advantage of this method for patterning spatial compositions is the control of surface coverage in both space and time. The thesis is organized into two parts. In Part I, formation and characterization of 1- and 2-component alkanethiol monolayer gradients is investigated. Numerous surface science tools are employed to examine the distribution in coverage obtained by application of in-plane potential gradients. Macroscopic characterization was obtained by sessile water drop contact angle measurements and surface plasmon resonance imaging. Gradients were also imaged on micron length scales with pulsed-force mode atomic force microscopy. Direct chemical evidence of surface compositions in aromatic thiol surface coverage was obtained by surface-enhanced Raman spectroscopy. In Part II, the applications of in-plane potential

  17. Development of modified vibration test criteria for qualifying space vehicle components

    NASA Technical Reports Server (NTRS)

    Chang, K. Y.; Kao, G. C.

    1976-01-01

    The results of the evaluation of two response prediction methods relating to the prediction of structural responses of stiffened shell structures with or without attached components, and subjected to broadband acoustic excitations are presented. The methods under evaluation were the constant mass attenuation method and the impedance ratio method. Example problems were used to illustrate the application procedures of these two methods and to compare their predicted results with the experimentally measured data. It is found that more realistic estimates of the structural response can be obtained by the impedance ratio method.

  18. Development of a Nonlinear Cumulative Fatigue Damage Methodology for Aircraft Engine Components under Multiaxial Loadings

    DTIC Science & Technology

    2007-04-01

    fatigue damage accumulation under a variety of loading conditions. These models are, for the most part, empirical approaches that have relied little on...elastic-plastic stresses listed in this table represent the surface stresses at maximum and minimum loads as determined by an elastic-plastic finite...Torsion,Load Control • R=-1 .Torsion.Strain Control © R-0,Torsion,Strain Control ■ Proportional • R=-1 .Torsion,Load Control A Runout ■ \\ n 0 X

  19. Progress in the spectacle correction of presbyopia. Part 1: Design and development of progressive lenses.

    PubMed

    Meister, Darryl J; Fisher, Scott W

    2008-05-01

    Most of the commercial advances in the spectacle correction of presbyopia continue to occur in progressive lens design, which has been the focus of intense research and development over the past 60 years by major spectacle lens manufacturers. While progressive lens design and manufacturing techniques have advanced at a steady pace, recent progress in 'free-form' lens surfacing has opened up many exciting possibilities that will in all likelihood bring about a paradigm shift in the current model of progressive lens fabrication and distribution. The first installment of this two-part series will review the fundamental optical principles and early development work associated with progressive lenses.

  20. Metallic wear debris sensors: promising developments in failure prevention for wind turbine gearsets and similar components

    NASA Astrophysics Data System (ADS)

    Poley, Jack; Dines, Michael

    2011-04-01

    Wind turbines are frequently located in remote, hard-to-reach locations, making it difficult to apply traditional oil analysis sampling of the machine's critical gearset at timely intervals. Metal detection sensors are excellent candidates for sensors designed to monitor machine condition in vivo. Remotely sited components, such as wind turbines, therefore, can be comfortably monitored from a distance. Online sensor technology has come of age with products now capable of identifying onset of wear in time to avoid or mitigate failure. Online oil analysis is now viable, and can be integrated with onsite testing to vet sensor alarms, as well as traditional oil analysis, as furnished by offsite laboratories. Controlled laboratory research data were gathered from tests conducted on a typical wind turbine gearbox, wherein total ferrous particle measurement and metallic particle counting were employed and monitored. The results were then compared with a physical inspection for wear experienced by the gearset. The efficacy of results discussed herein strongly suggests the viability of metallic wear debris sensors in today's wind turbine gearsets, as correlation between sensor data and machine trauma were very good. By extension, similar components and settings would also seem amenable to wear particle sensor monitoring. To our knowledge no experiments such as described herein, have previously been conducted and published.

  1. Development and characterization of fatigue resistant Aramid reinforced aluminium laminates (ARALL) for fatigue Critical aircraft components

    NASA Astrophysics Data System (ADS)

    Qaiser, M. H.; Umar, S.; Nauman, S.

    2014-06-01

    The structural weight of an aircraft has always been a controlling parameter that governs its fuel efficiency and transport capacity. In pursuit of achieving light-weight aircraft structures, high design stress levels have to be adopted and materials with high specific strength such as Aluminum etc. are to be deployed. However, an extensive spectrum of fatigue load exists at the aircraft wings and other aerodynamic components that may cause initiation and propagation of fatigue cracks and concludes in a catastrophic rupture. Fatigue is therefore the limiting design parameter in such cases and materials with high fatigue resistance are then required. A major improvement in the fatigue behavior was observed by laminating Kevlar fibers with Aluminum using epoxy. ARALL (Aramid Reinforced ALuminum Laminates) is a fatigue resistant hybrid composite that consists of layers of thin high strength aluminum alloy sheets surface bonded with aramid fibers. The intact aramid fibers tie up the fatigue cracks, thus reducing the stress intensity factor at the crack tip as a result of which the fatigue properties of can be enhanced with orders of magnitude as compared to monolithic high strength Aluminum alloy sheets. Significant amount of weight savings can be achieved in fatigue critical components in comparison with the traditional materials used in aircraft.

  2. Workshop Report on Additive Manufacturing for Large-Scale Metal Components - Development and Deployment of Metal Big-Area-Additive-Manufacturing (Large-Scale Metals AM) System

    SciTech Connect

    Babu, Sudarsanam Suresh; Love, Lonnie J.; Peter, William H.; Dehoff, Ryan

    2016-05-01

    ) systems development, (iv) material feedstock, (v) process planning, (vi) residual stress & distortion, (vii) post-processing, (viii) qualification of parts, (ix) supply chain and (x) business case. Furthermore, an open innovation network methodology was proposed to accelerate the development and deployment of new large-scale metal additive manufacturing technology with the goal of creating a new generation of high deposition rate equipment, affordable feed stocks, and large metallic components to enhance America’s economic competitiveness.

  3. Performance-based landfill design: development of a design component selection matrix using GIS and system simulation models

    NASA Astrophysics Data System (ADS)

    Tarhan, Başak; Ünlü, Kahraman

    2005-11-01

    Designing environmentally safe and economically feasible landfills can be a challenging task due to complex interactions that need to be taken into account between landfill size, waste and site characteristics. The main focus of this study is, by interfacing the geographic information systems (GIS) with system simulation models (SSM), to develop a methodology and a landfill design component selection matrix that can enable the determination of landfill design components providing the desired performance with minimal design details. In this paper, the conceptual framework and applications of the developed methodology demonstrating the selection of landfill design components that are suitable for the existing site conditions are presented. The conceptual model defines design variables, performance criteria and design components of a landfill. GIS and SSM are used to handle the site-specific data and to evaluate the landfill performance, respectively. Results indicate that the landfills having the same design characteristics show different performance under different site conditions; therefore, a landfill design that is technically and economically feasible should be selected on the basis of performance.

  4. Development and testing of a 20-kHz component test bed

    NASA Technical Reports Server (NTRS)

    Button, Robert M.; Brush, Andrew S.; Sundberg, Richard C.

    1989-01-01

    A history of the General Dynamics Space Systems Division 20 kHz Breadboard is presented including its current configuration and its role in the Space Station Freedom (SSF) program. Highlights and results are presented on a series of tests conducted on the 20 kHz Breadboard. The first test presented is the 20 kHz Breadboard Acceptance test. This test verified the operation of the delivered Breadboard and also characterized the main components of the system. Next, an indepth efficiency testing effort is presented. The tests attempted to apportion all the power losses in the 20 kHz Breadboard Main Invert Units. Distortion test data is presented showing the distortion characteristics of a Mapham inverter. Lastly, current work on the 20 kHz Breadboard is presented including Main Inverter Unit paralleling tests. Conclusions are summarized and references given.

  5. Development and tests of molybdenum armored copper components for MITICA ion source

    SciTech Connect

    Pavei, Mauro Marcuzzi, Diego; Rizzolo, Andrea; Valente, Matteo; Böswirth, Bernd; Greuner, Henri

    2016-02-15

    In order to prevent detrimental material erosion of components impinged by back-streaming positive D or H ions in the megavolt ITER injector and concept advancement beam source, a solution based on explosion bonding technique has been identified for producing a 1 mm thick molybdenum armour layer on copper substrate, compatible with ITER requirements. Prototypes have been recently manufactured and tested in the high heat flux test facility Garching Large Divertor Sample Test Facility (GLADIS) to check the capability of the molybdenum-copper interface to withstand several thermal shock cycles at high power density. This paper presents both the numerical fluid-dynamic analyses of the prototypes simulating the test conditions in GLADIS as well as the experimental results.

  6. Design and development of application-specific microfluidic components for flow control

    NASA Astrophysics Data System (ADS)

    Xu, Bai; Castracane, James; Altemus, Bruce; Keijmel, Jeroen; Heuzinkveld, Martijn

    2003-01-01

    There has been a growing interest in the research of microfluidic management systems, e.g., for DNA sequencing devices, biological cell manipulation systems, chemical analysis systems and microdosage systems. microfluidic management is crucial capability in most biomedical nanodevices and micro fuel cells using methanol as fuel. It involves the manipulation of fluids ranging from a scale of nano to millimeters. Basic building components for a microfluidic management system are microvalves and micropump s together with the interconnect fluidic channels . Micropumps can have passive and/or active valve. Because of the increasing functionality in portable electronic devices and systems, the micropumps and mic rovalves should be compact, reliable, long-lifetime and high energy efficient. In this report, the design, fabrication and modeling of a low power, low voltage, leak proof microfluidic management systems will be discussed.

  7. Dynamic analysis of a flexible spacecraft with rotating components. Volume 1: Analytical developments

    NASA Technical Reports Server (NTRS)

    Bodley, C. S.; Devers, A. D.; Park, A. C.

    1975-01-01

    Analytical procedures and digital computer code are presented for the dynamic analysis of a flexible spacecraft with rotating components. Topics, considered include: (1) nonlinear response in the time domain, and (2) linear response in the frequency domain. The spacecraft is assumed to consist of an assembly of connected rigid or flexible subassemblies. The total system is not restricted to a topological connection arrangement and may be acting under the influence of passive or active control systems and external environments. The analytics and associated digital code provide the user with the capability to establish spacecraft system nonlinear total response for specified initial conditions, linear perturbation response about a calculated or specified nominal motion, general frequency response and graphical display, and spacecraft system stability analysis.

  8. Development and tests of molybdenum armored copper components for MITICA ion source.

    PubMed

    Pavei, Mauro; Böswirth, Bernd; Greuner, Henri; Marcuzzi, Diego; Rizzolo, Andrea; Valente, Matteo

    2016-02-01

    In order to prevent detrimental material erosion of components impinged by back-streaming positive D or H ions in the megavolt ITER injector and concept advancement beam source, a solution based on explosion bonding technique has been identified for producing a 1 mm thick molybdenum armour layer on copper substrate, compatible with ITER requirements. Prototypes have been recently manufactured and tested in the high heat flux test facility Garching Large Divertor Sample Test Facility (GLADIS) to check the capability of the molybdenum-copper interface to withstand several thermal shock cycles at high power density. This paper presents both the numerical fluid-dynamic analyses of the prototypes simulating the test conditions in GLADIS as well as the experimental results.

  9. Development and tests of molybdenum armored copper components for MITICA ion source

    NASA Astrophysics Data System (ADS)

    Pavei, Mauro; Böswirth, Bernd; Greuner, Henri; Marcuzzi, Diego; Rizzolo, Andrea; Valente, Matteo

    2016-02-01

    In order to prevent detrimental material erosion of components impinged by back-streaming positive D or H ions in the megavolt ITER injector and concept advancement beam source, a solution based on explosion bonding technique has been identified for producing a 1 mm thick molybdenum armour layer on copper substrate, compatible with ITER requirements. Prototypes have been recently manufactured and tested in the high heat flux test facility Garching Large Divertor Sample Test Facility (GLADIS) to check the capability of the molybdenum-copper interface to withstand several thermal shock cycles at high power density. This paper presents both the numerical fluid-dynamic analyses of the prototypes simulating the test conditions in GLADIS as well as the experimental results.

  10. The development of optical techniques for component inspection in the aerospace industry

    NASA Astrophysics Data System (ADS)

    Irving, Paul Anthony

    A key requirement discussed within this thesis is feature extraction, in particular line segments. The Hough Transform is an elegant feature extraction technique for image analysis which performs well in noisy scenes and where occlusion may be problematic. Since its inception by P. V. C. Hough in 1962 for the detection of lines in bubble chambers, it has been widely researched, but minimal machine vision applications of the Hough Transform have been implemented. This lack of an application for the Hough Transform, coupled with the need for experimentation of an optical probe based on a conventional granite bed Coordinate Measuring Machine (CMM) is addressed. This latter requirement is currently fulfilled by mechanical touch trigger probes, or where optical techniques are used, back-illuminated glass tables. The suitability of the Hough Transform for machine vision inspection tasks is analyzed, and conclusions are drawn on whether or not useful results can be obtained by mounting a camera on the head of a CMM coupled with illumination from above. The industrial application addressed a drill and rout template digitizing within the aerospace industry; furthermore, the Hough Transform is also demonstrated for object recognition with a view to automatic component datum setting. New methods are illustrated for efficient, high accuracy Hough Transformation. Techniques are given for peak extraction in Hough space, enabling the isolation of all peaks irrespective of comparative magnitude, thereby eliminating the need for thresholding. Software data structures are shown to be an efficient method for implementing the above, especially with the later processing stages involving component boundary segment parsing.

  11. Expanding a Model for Affective Development: Implications for an Activity Component.

    ERIC Educational Resources Information Center

    McCrary, Nancye E.

    One useful framework for understanding and articulating instructional design to change biased beliefs is the Martin and Reigeluth model for affective development, appearing in Volume II of Reigeluth's "Instructional-Design Theories and Models" (1999). Using this recently developed framework to examine a Web-based multimedia instructional program…

  12. Using Components of Mathematical Ability for Initial Development and Identification of Mathematically Promising Students

    ERIC Educational Resources Information Center

    Vilkomir, T.; O'Donoghue, J.

    2009-01-01

    Kruteskii's work on the mathematical abilities of school children is a seminal work on the nature of mathematical ability. However, the task of developing methods for the practical application of his work is still a significant problem in mathematics education. The authors have developed a practical application of Kruteskii's approach to the…

  13. Projections from the cat posterior lateral hypothalamus to the ventral part of the oral pontine reticular nucleus contain a GABAergic component.

    PubMed

    De La Roza, Carmen; Martínez-Mena, Juana; Sánchez-Valle, María Elena; Reinoso-Suárez, Fernando

    2004-09-10

    The posterior lateral hypothalamus (PLH) has long been considered crucial to normal wakefulness while the ventral part of the oral pontine reticular nucleus (vRPO) is involved in the generation and maintenance of rapid eye movement (REM) sleep. However, to date, there is no information on the ultrastructure or neurotransmitter content of the hypothalamo-reticular projection. In the present study, we examined the morphology and synaptic organization of PLH terminals in the vRPO using PLH injections of biotinylated dextran amine (BDA) as well as of wheat germ agglutinin conjugated to horseradish peroxidase (WGA-HRP). Since some PLH neurons are GABAergic, we used a post-embedding immunogold technique to determine whether any anterogradely labeled terminals were GABA-immunopositive. Electron microscope analyses revealed a variety of ultrastructural features in the vRPO anterogradely labeled terminals. Although most labeled terminals (over 63%) formed symmetric synapses on vRPO somata and dendrites, others made asymmetric synapses on vRPO dendrites. The relative percentages of labeled terminals observed on large, medium and small diameter dendrites were 44.3 +/- 5.5%, 35.3 +/- 3.0% and 20.4 +/- 3.1%, respectively. Finally, post-embedding immunogold technique revealed that there are GABA-immunopositive and immunonegative components to this projection, indicating that GABA is one of the transmitters used by the PLH cells that project to the vRPO. Furthermore, most, if not all, of the GABA-labeled axon terminals formed symmetric synapsis. In conclusion, our results suggest that the PLH could modulate the physiological responses of vRPO neurons through a GABAergic pathway as well as by other inhibitory and/or excitatory pathways. Activation of the descending PLH GABAergic projection may inhibit the REM sleep-inducing neurons within the vRPO and thus contribute to the suppression of REM sleep activation during wakefulness.

  14. Forecasting peak daily ozone levels: part 2--A regression with time series errors model having a principal component trigger to forecast 1999 and 2002 ozone levels.

    PubMed

    Liu, Pao-Wen Grace; Johnson, Richard

    2003-12-01

    A modified time series approach, a Box-Jenkins regression with time series errors (RTSE) model plus a principal component (PC) trigger, has been developed to forecast peak daily 1-hr ozone (O3) in real time at the University of Wisconsin-Milwaukee North (UWM-N) during 1999 and 2002. The PC trigger acts as a predictor variable in the RTSE model. It tries to answer the question: will the next day be a possible high O3 day? To answer this question, three PC trigger rules were developed: (1) Hi-Low Checklist, (2) Discriminant Function Approach I, and (3) Discriminant Function Approach II. Also, a pure RTSE model without including the PC trigger and a persistence approach were tested for comparison. The RTSE model with DFA I successfully forecast the only two 1-hr federal exceedances (124 ppb), one in 1999 and one in 2002. In terms of the O3 100-ppb exceedances, 60-80% of the incorrect forecasts occurred with incorrect PC decisions. A few others may have been caused by unexpected O3-weather relations. When the three approaches used UWM-N data to forecast a 100-ppb exceedance somewhere in the Milwaukee, WI, metropolitan area, their performance was dramatically improved: the false alarm rate was reduced from 0.89 to 0.44, and the probability of detection was increased from 0.71 to 0.88.

  15. Developing a complex independent component analysis technique to extract non-stationary patterns from geophysical time-series

    NASA Astrophysics Data System (ADS)

    Forootan, Ehsan; Kusche, Jürgen

    2016-04-01

    Geodetic/geophysical observations, such as the time series of global terrestrial water storage change or sea level and temperature change, represent samples of physical processes and therefore contain information about complex physical interactionswith many inherent time scales. Extracting relevant information from these samples, for example quantifying the seasonality of a physical process or its variability due to large-scale ocean-atmosphere interactions, is not possible by rendering simple time series approaches. In the last decades, decomposition techniques have found increasing interest for extracting patterns from geophysical observations. Traditionally, principal component analysis (PCA) and more recently independent component analysis (ICA) are common techniques to extract statistical orthogonal (uncorrelated) and independent modes that represent the maximum variance of observations, respectively. PCA and ICA can be classified as stationary signal decomposition techniques since they are based on decomposing the auto-covariance matrix or diagonalizing higher (than two)-order statistical tensors from centered time series. However, the stationary assumption is obviously not justifiable for many geophysical and climate variables even after removing cyclic components e.g., the seasonal cycles. In this paper, we present a new decomposition method, the complex independent component analysis (CICA, Forootan, PhD-2014), which can be applied to extract to non-stationary (changing in space and time) patterns from geophysical time series. Here, CICA is derived as an extension of real-valued ICA (Forootan and Kusche, JoG-2012), where we (i) define a new complex data set using a Hilbert transformation. The complex time series contain the observed values in their real part, and the temporal rate of variability in their imaginary part. (ii) An ICA algorithm based on diagonalization of fourth-order cumulants is then applied to decompose the new complex data set in (i

  16. Predictive models of safety based on audit findings: Part 1: Model development and reliability.

    PubMed

    Hsiao, Yu-Lin; Drury, Colin; Wu, Changxu; Paquet, Victor

    2013-03-01

    This consecutive study was aimed at the quantitative validation of safety audit tools as predictors of safety performance, as we were unable to find prior studies that tested audit validity against safety outcomes. An aviation maintenance domain was chosen for this work as both audits and safety outcomes are currently prescribed and regulated. In Part 1, we developed a Human Factors/Ergonomics classification framework based on HFACS model (Shappell and Wiegmann, 2001a,b), for the human errors detected by audits, because merely counting audit findings did not predict future safety. The framework was tested for measurement reliability using four participants, two of whom classified errors on 1238 audit reports. Kappa values leveled out after about 200 audits at between 0.5 and 0.8 for different tiers of errors categories. This showed sufficient reliability to proceed with prediction validity testing in Part 2.

  17. Automated procedure for developing hybrid computer simulations of turbofan engines. Part 1: General description

    NASA Technical Reports Server (NTRS)

    Szuch, J. R.; Krosel, S. M.; Bruton, W. M.

    1982-01-01

    A systematic, computer-aided, self-documenting methodology for developing hybrid computer simulations of turbofan engines is presented. The methodology that is pesented makes use of a host program that can run on a large digital computer and a machine-dependent target (hybrid) program. The host program performs all the calculations and data manipulations that are needed to transform user-supplied engine design information to a form suitable for the hybrid computer. The host program also trims the self-contained engine model to match specified design-point information. Part I contains a general discussion of the methodology, describes a test case, and presents comparisons between hybrid simulation and specified engine performance data. Part II, a companion document, contains documentation, in the form of computer printouts, for the test case.

  18. Calculation of stress intensity factors in an isotropic multicracked plate. Part 1: Theoretical development

    NASA Technical Reports Server (NTRS)

    Binienda, W. K.; Arnold, S. M.; Tan, H. Q.

    1992-01-01

    An essential part of describing the damage state and predicting the damage growth in a multicracked plate is the accurate calculation of stress intensity factors (SIF's). Here, a methodology and rigorous solution formulation for SIF's of a multicracked plate, with fully interacting cracks, subjected to a far-field arbitrary stress state is presented. The fundamental perturbation problem is derived, and the steps needed to formulate the system of singular integral equations whose solution gives rise to the evaluation of the SIF's are identified. This analytical derivation and numerical solution are obtained by using intelligent application of symbolic computations and automatic FORTRAN generation capabilities (described in the second part of this paper). As a result, a symbolic/FORTRAN package, named SYMFRAC, that is capable of providing accurate SIF's at each crack tip was developed and validated.

  19. Part 1. Characterization of roadway asphalts by solubility studies. Part 2. Development of concrete applicant organo-functional silanes

    SciTech Connect

    Lee, W.D.

    1993-01-01

    Part 1. Solubility profiles describe the chemical constitution of asphalt in terms of internal solubility phenomena. In this study the solubility parameter (r) which is related to hydrogen bonding or associative interactions and the volume dependent solubility parameter (V) which is related to London dispersion forces (non-polar interactions) and the dipole-dipole polar interactions. The plot by the solubility coordinates (r, V) of the solvents and the solubility of the asphalt is termed the solubility profile. Solubility profile data can be related to roadway performance. Roadway asphalt aging can be followed visually and mathematically by the detailed analysis of time-lapsed solubility profiles of roadway core asphalts. The profiles can be used to describe the gross chemical changes without the need to identify or isolate pure substances. This report investigates thirty-two roadway projects constructed between February 1983 and August 1987 which have been monitored for condition and followed by a series of solubility profiles for up to 60 months. Part 2. A variety of organosilanes have been used as applicants to roadway surfaces thereby extending the life or service of the roadway. The aim of this research project is to synthesize and characterize several organosilane compounds with potential concrete roadway applications. Alkyltrialkoxysilanes can be used to stop salt from penetrating concrete and resultant rebar corrosion. The first area this project deals with the optimization of the catalytic synthesis of n-octyltrichloro-and n-decyltrichlorosilane and their alkoxy derivatives. The investigation includes a study of the type and amount of catalyst and a study of varying reaction conditions. The second area of research involves the synthesis and characterization of a set of UV-absorbing/VIS-emitting organosiloxanes. These compounds have potential use as roadway delineation or roadway obstruction demarkation product enhancements.

  20. Status on the Component Models Developed in the Modelica Framework: High-Temperature Steam Electrolysis Plant & Gas Turbine Power Plant

    SciTech Connect

    Suk Kim, Jong; McKellar, Michael; Bragg-Sitton, Shannon M.; Boardman, Richard D.

    2016-10-01

    This report has been prepared as part of an effort to design and build a modeling and simulation (M&S) framework to assess the economic viability of a nuclear-renewable hybrid energy system (N-R HES). In order to facilitate dynamic M&S of such an integrated system, research groups in multiple national laboratories have been developing various subsystems as dynamic physics-based components using the Modelica programming language. In fiscal year (FY) 2015, Idaho National Laboratory (INL) performed a dynamic analysis of two region-specific N-R HES configurations, including the gas-to-liquid (natural gas to Fischer-Tropsch synthetic fuel) and brackish water reverse osmosis desalination plants as industrial processes. In FY 2016, INL has developed two additional subsystems in the Modelica framework: a high-temperature steam electrolysis (HTSE) plant and a gas turbine power plant (GTPP). HTSE has been proposed as a high priority industrial process to be integrated with a light water reactor (LWR) in an N-R HES. This integrated energy system would be capable of dynamically apportioning thermal and electrical energy (1) to provide responsive generation to the power grid and (2) to produce alternative industrial products (i.e., hydrogen and oxygen) without generating any greenhouse gases. A dynamic performance analysis of the LWR/HTSE integration case was carried out to evaluate the technical feasibility (load-following capability) and safety of such a system operating under highly variable conditions requiring flexible output. To support the dynamic analysis, the detailed dynamic model and control design of the HTSE process, which employs solid oxide electrolysis cells, have been developed to predict the process behavior over a large range of operating conditions. As first-generation N-R HES technology will be based on LWRs, which provide thermal energy at a relatively low temperature, complementary temperature-boosting technology was suggested for integration with the

  1. Developing an “Evidence-Based Medicine and Use of the Biomedical Literature” component as a longitudinal theme of an outcomes-based medical school curriculum: year 1

    PubMed Central

    Burrows, Suzetta; Moore, Kelly; Arriaga, Joaquin; Paulaitis, Gediminas; Lemkau, Henry L.

    2003-01-01

    This paper describes the new outcomes-based curriculum at the University of Miami School of Medicine, a model curriculum for the first decade of the twenty-first century. The new curriculum has a strong emphasis on evidence-based medicine (EBM), implemented throughout its four years as a component of one of its longitudinal themes. The “EBM and Use of the Biomedical Literature” component, which begins at orientation, was developed and is implemented by the Louis Calder Memorial Library, the center of EBM focus and activity for the curriculum and other initiatives at the University of Miami/Jackson Memorial Medical Center. The authors are unaware of any published reports of library-centric EBM initiatives as part of a longitudinal theme of a four-year outcomes-based curriculum. Other innovations of the EBM component in the new curriculum to date include use of BlackboardTM and CATmakerTM software programs for self-paced, interactive educational opportunities. PMID:12568156

  2. Projects at the Component Development and Integration Facility. Quarterly technical progress report, July 1--September 30, 1993

    SciTech Connect

    Not Available

    1993-12-31

    This quarterly technical progress report presents progress on the projects at the Component Development and Integration Facility (CDIF) during the first quarter of FY94. The CDIF is a major US Department of Energy test facility in Butte, Montana, operated by MSE, Inc. Projects in progress include: MHD Proof-of-Concept project; mine waste technology pilot program; plasma projects; resource recovery project; sodium sulfide/ferrous sulfate project; soil washing project; and spray casting project.

  3. Projects at the Component Development and Integration Facility. Quarterly technical progress report, April 1--June 30, 1993

    SciTech Connect

    Not Available

    1993-12-01

    This quarterly technical progress report presents progress on the projects at the Component Development and Integration Facility (CDIF) during the third quarter of FY93. The CDIF is a major US Department of Energy test facility in Butte, Montana, operated by MSE, Inc. Projects in progress include: MHD Proof-of-Concept Project; Mine Waste Technology Program; Plasma Projects; Resource Recovery Project; Sodium Sulfide/Ferrous Sulfate Project; Soil Washing Project; and Spray Casting Project.

  4. Projects at the Component Development and Integration Facility. Quarterly technical progress report, January 1, 1994--March 31, 1994

    SciTech Connect

    Not Available

    1994-08-01

    This quarterly technical progress report presents progress on the projects at the Component Development and Integration Facility (CDIF) during the second quarter of FY94. The CDIF is a major US Department of Energy test facility in Butte, Montana, operated by MSE, Inc. Projects in progress include: Biomass Remediation Project; Heavy Metal-Contaminated Soil Project; MHD Shutdown; Mine Waste Technology Pilot Program; Plasma Projects; Resource Recovery Project; Sodium Sulfide/Ferrous Sulfate Project; and Spray Casting Project.

  5. Vapor Compression Distillation Subsystem (VCDS) Component Enhancement, Testing and Expert Fault Diagnostics Development, Volume 2

    NASA Technical Reports Server (NTRS)

    Mallinak, E. S.

    1987-01-01

    A wide variety of Space Station functions will be managed via computerized controls. Many of these functions are at the same time very complex and very critical to the operation of the Space Station. The Environmental Control and Life Support System is one group of very complex and critical subsystems which directly affects the ability of the crew to perform their mission. Failure of the Environmental Control and Life Support Subsystems are to be avoided and, in the event of failure, repair must be effected as rapidly as possible. Due to the complex and diverse nature of the subsystems, it is not possible to train the Space Station crew to be experts in the operation of all of the subsystems. By applying the concepts of computer-based expert systems, it may be possible to provide the necessary expertise for these subsystems in dedicated controllers. In this way, an expert system could avoid failures and extend the operating time of the subsystems even in the event of failure of some components, and could reduce the time to repair by being able to pinpoint the cause of a failure when one cannot be avoided.

  6. Development and testing of an integrated smart tool holder for four-component cutting force measurement

    NASA Astrophysics Data System (ADS)

    Xie, Zhengyou; Lu, Yong; Li, Jianguang

    2017-09-01

    Cutting force measurement is a significant requirement for monitoring and controlling the machining processes. Hence, various methods of measuring the cutting force have been proposed by many researchers. In this study, an innovative integrated smart tool holder system based on capacitive sensors is designed, constructed and tested, which is capable of measuring triaxial cutting force and a torque simultaneously in a wireless environment system. A standard commercial tool holder is modified to make itself be the force sensing element that has advantages of simple structure and easy machining. Deformable beams are created in the tool holder, and the tiny deformations of which used to calculate the four-component cutting force are detected by six high precision capacitive sensors. All the sensors and other electronics, like data acquisition and transmitting unit, and wireless power unit, are incorporated into the tool holder as a whole system. The device is intended to be used in a rotating spindle such as in milling and drilling processes. Eventually, the static and dynamic characteristics of the smart tool holder have been determined by a series of tests. Cutting tests have also been carried out and the results show it is stable and practical to measure the cutting force in milling and drilling processes.

  7. In vitro diagnosis of Hymenoptera venom allergy and further development of component resolved diagnostics.

    PubMed

    Ebo, Didier G; Van Vaerenbergh, Matthias; de Graaf, Dirk C; Bridts, Chris H; De Clerck, Luc S; Sabato, Vito

    2014-03-01

    For most people Hymenoptera stings result in transient and bothersome local inflammatory responses characterized by pain, itching, redness and swelling. In contrast, for those presenting an IgE-mediated allergic reaction, a re-sting may cause life-threatening reactions. In such patients, correct diagnosis is an absolute prerequisite for effective management, i.e. venom-specific immunotherapy. Generally, identification of the offending insect involves a detailed history along with quantification of venom-specific IgE antibodies and venom skin tests. Unfortunately, due to uncertainties associated with both tests, correct diagnosis is not always straightforward. This review summarizes the potentials and limitations of the various in vitro tests that are currently being used in the diagnosis of Hymenoptera venom allergy. Particular attention is paid to the potential of novel cellular tests such as basophil activation tests and component-resolved diagnosis with recombinant venom allergens in the diagnostic approach of patients with difficult diagnosis, i.e. cases in whom traditional venom specific IgE and skin tests yield equivocal or negative results. Finally, this review also covers the recent discoveries in the field of proteome research of Hymenoptera venoms and the selection of cell types for recombinant allergens production.

  8. Vangl1 and Vangl2: planar cell polarity components with a developing role in cancer

    PubMed Central

    Hatakeyama, Jason; Wald, Jessica H; Printsev, Ignat; Ho, Hsin-Yi Henry; Carraway, Kermit L

    2015-01-01

    Cancers commonly reactivate embryonic developmental pathways to promote the aggressive behavior of their cells, resulting in metastasis and poor patient outcome. While developmental pathways such as canonical Wnt signaling and epithelial-to-mesenchymal transition have received much attention, our understanding of the role of the planar cell polarity (PCP) pathway in tumor progression remains rudimentary. Protein components of PCP, including a subset that overlaps with the canonical Wnt pathway, partition in polarized epithelial cells along the planar axis and are required for the establishment and maintenance of lateral epithelial polarity. Significant insight into PCP regulation of developmental and cellular processes has come from analysis of the functions of the core PCP scaffolding proteins Vangl1 and Vangl2. In particular, studies on zebrafish and with Looptail (Lp) mice, which harbor point mutations in Vangl2 that alter its trafficking and localization, point to roles for the PCP pathway in maintaining cell polarization along both the apical–basal and planar axes as well as in collective cell motility and invasiveness. Recent findings have suggested that the Vangls can promote similar processes in tumor cells. Initial data-mining efforts suggest that VANGL1 and VANGL2 are dysregulated in human cancers, and estrogen receptor (ER)-positive breast cancer patients whose tumors exhibit elevated VANGL1 expression suffer from shortened overall survival. Overall, evidence is beginning to accumulate that the heightened cellular motility and invasiveness associated with PCP reactivation may contribute to the malignancy of some cancer subtypes. PMID:24981109

  9. Energy Conversion Alternatives Study (ECAS), General Electric Phase 1. Volume 3: Energy conversion subsystems and components. Part 1: Bottoming cycles and materials of construction

    NASA Technical Reports Server (NTRS)

    Shah, R. P.; Solomon, H. D.

    1976-01-01

    Energy conversion subsystems and components were evaluated in terms of advanced energy conversion systems. Results of the bottoming cycles and materials of construction studies are presented and discussed.

  10. Vegetation component of geothermal EIS studies: Introduced plants, ecosystem stability, and geothermal development

    NASA Astrophysics Data System (ADS)

    1994-10-01

    This paper contributes new information about the impacts from introduced plant invasions on the native Hawaiian vegetation as consequences of land disturbance and geothermal development activities. In this regard, most geothermal development is expected to act as another recurring source of physical disturbance which favors the spread and maintenance of introduced organisms throughout the region. Where geothermal exploration and development activities extend beyond existing agricultural and residential development, they will become the initial or sole source of disturbance to the naturalized vegetation of the area. Kilauea has a unique ecosystem adapted to the dynamics of a volcanically active landscape. The characteristics of this ecosystem need to be realized in order to understand the major threats to the ecosystem and to evaluate the effects of and mitigation for geothermal development in Puna. The native Puna vegetation is well adapted to disturbances associated with volcanic eruption, but it is ill-adapted to compete with alien plant species in secondary disturbances produced by human activities. Introduced plant and animal species have become a major threat to the continued presence of the native biota in the Puna region.

  11. Vegetation component of geothermal EIS studies: Introduced plants, ecosystem stability, and geothermal development

    SciTech Connect

    1994-10-01

    This paper contributes new information about the impacts from introduced plant invasions on the native Hawaiian vegetation as consequences of land disturbance and geothermal development activities. In this regard, most geothermal development is expected to act as another recurring source of physical disturbance which favors the spread and maintenance of introduced organisms throughout the region. Where geothermal exploration and development activities extend beyond existing agricultural and residential development, they will become the initial or sole source of disturbance to the naturalized vegetation of the area. Kilauea has a unique ecosystem adapted to the dynamics of a volcanically active landscape. The characteristics of this ecosystem need to be realized in order to understand the major threats to the ecosystem and to evaluate the effects of and mitigation for geothermal development in Puna. The native Puna vegetation is well adapted to disturbances associated with volcanic eruption, but it is ill-adapted to compete with alien plant species in secondary disturbances produced by human activities. Introduced plant and animal species have become a major threat to the continued presence of the native biota in the Puna region of reference.

  12. Energy efficient engine. Volume 2. Appendix A: Component development and integration program

    NASA Technical Reports Server (NTRS)

    Moracz, D. J.; Cook, C. R.

    1981-01-01

    The large size and the requirement for precise lightening cavities in a considerable portion of the titanium fan blades necessitated the development of a new manufacturing method. The approach which was selected for development incorporated several technologies including HIP diffusion bonding of titanium sheet laminates containing removable cores and isothermal forging of the blade form. The technology bases established in HIP/DB for composite blades and in isothermal forging for fan blades were applicable for development of the manufacturing process. The process techniques and parameters for producing and inspecting the cored diffusion bonded titanium laminate blade preform were established. The method was demonstrated with the production of twelve hollow simulated blade shapes for evaluation. Evaluations of the critical experiments conducted to establish procedures to produce hollow structures by a laminate/core/diffusion bonding approach are included. In addition the transfer of this technology to produce a hollow fan blade is discussed.

  13. Development of Acid Functional Groups and Lactones During the Thermal Degradation of Wood and Wood Components

    USGS Publications Warehouse

    Rutherford, David W.; Wershaw, Robert L.; Reeves, James B.

    2008-01-01

    Black carbon (pyrogenic materials including chars) in soils has been recognized as a substantial portion of soil organic matter, and has been shown to play a vital role in nutrient cycling; however, little is known concerning the properties of this material. Previous studies have largely been concerned with the creation of high-surface-area materials for use as sorbents. These materials have been manufactured at high temperature and have often been activated. Chars occurring in the environment can be formed over a wide range of temperature. Because it is extremely difficult to isolate black carbon once it has been incorporated in soils, chars produced in the laboratory under controlled conditions can be used to investigate the range of properties possible for natural chars. This report shows that charring conditions (temperature and time) have substantial impact on the acid functional group and lactone content of chars. Low temperatures (250?C) and long charring times (greater than 72 hours) produce chars with the highest acid functional group and lactone content. The charring of cellulose appears to be responsible for the creation of the acid functional group and lactones. The significance of this study is that low-temperature chars can have acid functional group contents comparable to humic materials (as high as 8.8 milliequivalents per gram). Acid functional group and lactone content decreases as charring temperature increases. The variation in formation conditions expected under natural fire conditions will result in a wide range of sorption properties for natural chars which are an important component of soil organic matter. By controlling the temperature and duration of charring, it is possible to tailor the sorption properties of chars, which may be used as soil amendments.

  14. Developing Training Exemplars for the Requisite Components of Visual Threat Detection

    DTIC Science & Technology

    2012-09-01

    construed as an official Department of the Army position, unless so designated by other authorized documents. i REPORT DOCUMENTATION PAGE 1... Design ............................................................................................................................. 34...activities in the OE. This report presents the findings from the final research phase and consists of a discussion of the design and development of the

  15. A Cognitive Component Analysis Approach for Developing Game-Based Spatial Learning Tools

    ERIC Educational Resources Information Center

    Hung, Pi-Hsia; Hwang, Gwo-Jen; Lee, Yueh-Hsun; Su, I-Hsiang

    2012-01-01

    Spatial ability has been recognized as one of the most important factors affecting the mathematical performance of students. Previous studies on spatial learning have mainly focused on developing strategies to shorten the problem-solving time of learners for very specific learning tasks. Such an approach usually has limited effects on improving…

  16. Technical Guidelines and References: Crops Training Component. From: Agricultural Development Workers Training Manual. Volume III: Crops.

    ERIC Educational Resources Information Center

    Peace Corps, Washington, DC. Information Collection and Exchange Div.

    This reference manual for training Peace Corps agricultural development workers deals with crops. The document begins with common units of area, length, weight, volume, and conversions between them. A practice problem is worked and other conversion problems are given. The second section is intended to show agricultural field workers how to survey…

  17. 24 CFR 1000.324 - How is the need component developed?

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... percent of formula median income reduced by the combination of current assisted stock and units developed...) Households with housing cost burden greater than 50 percent of formula annual income weighted at 22 percent; (b) AIAN Households which are overcrowded or without kitchen or plumbing weighted at 25 percent;...

  18. 24 CFR 1000.324 - How is the need component developed?

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... percent of formula median income reduced by the combination of current assisted stock and units developed...) Households with housing cost burden greater than 50 percent of formula annual income weighted at 22 percent; (b) AIAN Households which are overcrowded or without kitchen or plumbing weighted at 25 percent;...

  19. The roles of microRNAs and protein components of the microRNA pathway in lung development and diseases.

    PubMed

    Cushing, Leah; Jiang, Zhihua; Kuang, Pingping; Lü, Jining

    2015-04-01

    Decades of studies have shown evolutionarily conserved molecular networks consisting of transcriptional factors, diffusing growth factors, and signaling pathways that regulate proper lung development. Recently, microRNAs (miRNAs), small, noncoding regulatory RNAs, have been integrated into these networks. Significant advances have been made in characterizing the developmental stage- or cell type-specific miRNAs during lung development by using approaches such as genome-wide profiling and in situ hybridization. Results from gain- or loss-of-function studies revealed pivotal roles of protein components of the miRNA pathway and individual miRNAs in regulating proliferation, apoptosis, differentiation, and morphogenesis during lung development. Aberrant expression or functions of these components have been associated with pulmonary disorders, suggesting their involvement in pathogenesis of these diseases. Moreover, genetically modified mice generated in these studies have become useful models of human lung diseases. Challenges in this field include characterization of collective function and responsible targets of miRNAs specifically expressed during lung development, and translation of these basic findings into clinically relevant information for better understanding of human diseases. The goal of this review is to discuss the recent progress on the understanding of how the miRNA pathway regulates lung development, how dysregulation of miRNA activities contributes to pathogenesis of related pulmonary diseases, and to identify relevant questions and future directions.

  20. The quantification of biodiversity: an esoteric quest or a vital component of sustainable development?

    PubMed

    Lovejoy, T E

    1994-07-29

    Biodiversity relates to sustainable development through a series of direct and indirect uses. These include direct harvest, nature tourism, wild genes improving domestic crops, wild species contributing to crop productivity, pest management, sources of medicine and bioremediation (biologically based environmental clean-up). Biodiversity relates through services, individual species indicating environmental change or stress, insights into the life sciences and increasingly today, through wealth generated from biodiversity at the level of the molecule. Sustainable development relates to the quantification of biodiversity through organizing information to enable the foregoing activities. It also relates in little-explored ways to ecosystem function, stability and resilience. Biodiversity is already a proven indicator of environmental change in freshwater systems.

  1. Development of a Piezoelectric Vacuum Sensing Component for a Wide Pressure Range

    PubMed Central

    Wang, Bing-Yu; Hsieh, Fan-Chun; Lin, Che-Yu; Chen, Shao-En; Chen, Fong-Zhi; Wu, Chia-Che

    2014-01-01

    In this study, we develop a clamped–clamped beam-type piezoelectric vacuum pressure sensing element. The clamped–clamped piezoelectric beam is composed of a PZT layer and a copper substrate. A pair of electrodes is set near each end. An input voltage is applied to a pair of electrodes to vibrate the piezoelectric beam, and the output voltage is measured at the other pair. Because the viscous forces on the piezoelectric beam vary at different air pressures, the vibration of the beam depends on the vacuum pressure. The developed pressure sensor can sense a wide range of pressure, from 6.5 × 10−6 to 760 Torr. The experimental results showed that the output voltage is inversely proportional to the gas damping ratio, and thus, the vacuum pressure was estimated from the output voltage. PMID:25421736

  2. Development of a propulsion system and component test facility for advanced radioisotope powered Mars Hopper platforms

    SciTech Connect

    Robert C. O'Brien; Nathan D. Jerred; Steven D. Howe

    2011-02-01

    Verification and validation of design and modeling activities for radioisotope powered Mars Hopper platforms undertaken at the Center for Space Nuclear Research is essential for proof of concept. Previous research at the center has driven the selection of advanced material combinations; some of which require specialized handling capabilities. The development of a closed and contained test facility to forward this research is discussed within this paper.

  3. Development of a Five-Component Strain-Gauge Balance for the DSTO Water Tunnel

    DTIC Science & Technology

    2009-11-01

    IFOSTP ( International Follow on Structural Test Program ) Test for the F/A-18. He has accumulated...has been developed, enabling very small flow-induced forces and moments on models to be measured. This followed the successful implementation of a two...there to the Structures Division where he has been involved in Structural Instrumentation for large fatigue testing of both fixed-wing and

  4. Development and successful testing of MCP BSCCO-2212 components for a 10 MVA resistive superconducting fault current limiter

    NASA Astrophysics Data System (ADS)

    Bock, J.; Breuer, F.; Walter, H.; Noe, M.; Kreutz, R.; Kleimaier, M.; Weck, K.-H.; Elschner, S.

    2004-05-01

    The German government funded resistive superconducting fault current limiter project CURL 10 is based on bulk material and aims at the development of a three-phase prototype for the medium voltage level (10 kV, 10 MVA). The key element of the project is the development of suitable robust superconducting components. On the basis of the well known melt cast process (MCP) for BSCCO-2212, these are manufactured by cutting superconducting tubes to bifilar coils. At the operation temperature of 65 K a current density of 4000 A cm-2 was achieved. In order to protect the superconductor during limitation the component was equipped with an electrical shunt contacted on its entire length. Single-phase tests with nine of these components in series, corresponding to a protected load of 1.2 MVA, have been successfully accomplished and are described in detail. These tests include different types of short circuits as specified by the utilities within the project and included lightning surge loads up to 75 kV.

  5. Global public-private partnerships: Part I--A new development in health?

    PubMed Central

    Buse, K.; Walt, G.

    2000-01-01

    The proliferation of public-private partnerships is rapidly reconfiguring the international health landscape. This article (part I of two on the subject) traces the changing nature of partnership, and discusses the definitional and conceptual ambiguities surrounding the term. After defining global public-private partnerships (GPPPs) for health development, we analyse the factors which have led to the convergence of public and private actors and discuss the consequences of the trend toward partnership between UN agencies (including the World Bank) and commercial entities in the health sector. Generic factors such as globalization and disillusionment with the UN, and factors specific to the health sector, such as market failure in product development for orphan diseases, are examined. Reviewed are the interests, policies, practices and concerns of the UN, the private-for-profit sector, bilateral organizations, and governments of low-income countries with respect to public-private partnership. While GPPPs bring much needed resources to problems of international health, we highlight concerns regarding this new organizational format. Part II, which will be published in the May issue of the Bulletin, presents a conceptual framework for analysing health GPPPs and explores the issues raised. PMID:10885184

  6. Manufacturing technologies for photovoltaics and possible means of their development in Russia (Review). Part 1: General approach to the development of photoelectric converters and basic silicon technologies

    NASA Astrophysics Data System (ADS)

    Tarasenko, A. B.; Popel', O. S.

    2015-11-01

    The state and key tendencies of the development of basic technologies for manufacture of photoelectric converters (PECs) in the world are considered, and their advantages and disadvantages are discussed. The first part of the review gives short information on the development of photovoltaics in the world and planes of the development of solar power plants in Russia. Total power of photoelectric plants operating in various countries in 2015 exceeded 150 GW and increased in the last ten years with a rate of approximately 50% per year. Russia made important state decisions on the support of the development of renewable power engineering and developed mechanisms, which were attractive for business, on the stimulation of building of the network of solar power plants with a total power to 1.5 GW in the country to 2020. At the same time, the rigid demands are made with respect to the localization of the production of components of these plants that opens new abilities for the development of the domestic production of photovoltaics manufacture. Data on the efficiency of PECs of various types that are attained in the leading laboratories of the world are given. Particular emphasis has been placed on the consideration of basic silicon technologies of PEC manufacture, which had the widest commercial application. The basic methods for production of polycrystalline silicon and making single-crystal and multicrystal silicon are described. Fundamentals of making techniques for plates, PECs, and photoelectric modules based on single-crystal and polycrystalline silicon are considered. The second part will be devoted to modifications of manufacturing techniques for photoelectric converters, enhancement methods for contact structures, and recommendations of authors with respect to the choice of prospective technologies for the expansion of PEC production in Russia. It will involve formulations and substantiations of the most promising lines of the development of photoelectric

  7. Development of critical life stage assays: Teratogenic effects of SRS effluent components on freshwater fish, gambusia

    SciTech Connect

    Guram, M.S.

    1990-11-01

    The final report of the research carried out at Voorhees College contains a composite compilation of the last two years work. The data note variation in the number of young fish delivered per female vary markedly between several ponds on the SRS and of SRS ponds. The reasons for this are unknown at present. Initial research was carried out on the effects on the developing fish fetus of various substances that may have produced these variations. Further study is necessary to identify the factors that produce the observed alterations. 7 figs., 5 tabs.

  8. Searching for Components of Conceptual Ecology That Mediate Development of Epistemological Beliefs in Science

    NASA Astrophysics Data System (ADS)

    Deniz, Hasan

    2011-12-01

    This paper articulates the importance of epistemological beliefs (EBs) and draws a parallel between EBs literature in educational psychology and nature of science (NOS) literature in science education. The paper stresses that EBs in science and NOS ideas have common ground and they can be best improved through explicit-reflective instruction informed by conceptual change theory. The paper concludes that future studies should explore the factors that mediate the development of EBs in science and NOS ideas rather than documenting the changes in students' and teachers' EBs in science and NOS ideas after explicit-reflective instruction through pre- and post assessments.

  9. Advanced manufacturing development of a composite empennage component for L-1011 aircraft

    NASA Technical Reports Server (NTRS)

    1979-01-01

    Work on process verification and tooling development continued. The cover process development was completed with the decision to proceed with low resin content prepreg material (34 + or - 3% by weight) in the fabrication of production readiness verification test (PRVT) specimens and the full-scale covers. The structural integrity of the cover/joint design was verified with the successful test of the cover attachment to fuselage ancillary test specimen (H25). Failure occurred, as predicted, in the skin panel away from the fuselage joint at 141 percent of the design ultimate load. With the successful completion of the H25 test, the PRVT cover specimens, which are identical to the H25 ancillary test specimen, were cleared for production. Eight of the twenty cover specimens were fabricated and are in preparation for test. All twenty of the PRVT spar specimens were fabricated and also were prepared for test. The environmental chambers used in the durability test of ten cover and ten spar PRVT specimens were completed and installed in the load reaction frames.

  10. Developing Components and Curricula for a Research-Rich Undergraduate Degree in Computational Physics

    NASA Astrophysics Data System (ADS)

    Landau, Rubin

    2001-06-01

    A four-year undergraduate curriculum leading to a Bachelor's degree in Computational Physics is described. The courses, texts, and seminars are research- and Web-rich, and culminate in an Advanced Computational Science Laboratory derived from graduate theses and research from NPACI centers and national laboratories. There are important places for Maple, Java, MathML, MatLab, C and Fortran in the curriculum. The curriculum will be rich with web materials that are used and, at times, developed by the students. This reflects developments in our department and research groups over the last eight years in web-enhanced education, and our view that the web and computer-mediated instruction will play an increasing role in future scientific computing and education. The curriculum concludes with a completely new, advanced computational laboratory in which senior and graduate students will experiment with computer simulations taken from previous M.S. and Ph.D. research projects, as well as from research projects at national laboratories.

  11. What develops during emotional development? A component process approach to identifying sources of psychopathology risk in adolescence

    PubMed Central

    McLaughlin, Katie A.; Garrad, Megan C.; Somerville, Leah H.

    2015-01-01

    Adolescence is a phase of the lifespan associated with widespread changes in emotional behavior thought to reflect both changing environments and stressors, and psychological and neurobiological development. However, emotions themselves are complex phenomena that are composed of multiple subprocesses. In this paper, we argue that examining emotional development from a process-level perspective facilitates important insights into the mechanisms that underlie adolescents' shifting emotions and intensified risk for psychopathology. Contrasting the developmental progressions for the antecedents to emotion, physiological reactivity to emotion, emotional regulation capacity, and motivation to experience particular affective states reveals complex trajectories that intersect in a unique way during adolescence. We consider the implications of these intersecting trajectories for negative outcomes such as psychopathology, as well as positive outcomes for adolescent social bonds. PMID:26869841

  12. What develops during emotional development? A component process approach to identifying sources of psychopathology risk in adolescence.

    PubMed

    McLaughlin, Katie A; Garrad, Megan C; Somerville, Leah H

    2015-12-01

    Adolescence is a phase of the lifespan associated with widespread changes in emotional behavior thought to reflect both changing environments and stressors, and psychological and neurobiological development. However, emotions themselves are complex phenomena that are composed of multiple subprocesses. In this paper, we argue that examining emotional development from a process-level perspective facilitates important insights into the mechanisms that underlie adolescents' shifting emotions and intensified risk for psychopathology. Contrasting the developmental progressions for the antecedents to emotion, physiological reactivity to emotion, emotional regulation capacity, and motivation to experience particular affective states reveals complex trajectories that intersect in a unique way during adolescence. We consider the implications of these intersecting trajectories for negative outcomes such as psychopathology, as well as positive outcomes for adolescent social bonds.

  13. [Distribution of 137Cs, 90Sr and their chemical analogues in the components of an above-ground part of a pine in a quasi-equilibrium condition].

    PubMed

    Mamikhin, S V; Manakhov, D V; Shcheglov, A I

    2014-01-01

    The additional study of the distribution of radioactive isotopes of caesium and strontium and their chemical analogues in the above-ground components of pine in the remote from the accident period was carried out. The results of the research confirmed the existence of analogy in the distribution of these elements on the components of this type of wood vegetation in the quasi-equilibrium (relatively radionuclides) condition. Also shown is the selective possibility of using the data on the ash content of the components of forest stands of pine and oak as an information analogue.

  14. Development, growth and maintenance of β-cell mass: Models are also part of the story

    PubMed Central

    Khadra, Anmar; Schnell, Santiago

    2015-01-01

    Pancreatic β-cells in the islets of Langerhans play a crucial role in regulating glucose homeostasis in the circulation. Loss of β-cell mass or function due to environmental, genetic and immunological factors leads to the manifestation of diabetes mellitus. The mechanisms regulating the dynamics of pancreatic β-cell mass during normal development and diabetes progression are complex. To fully unravel such complexity, experimental and clinical approaches need to be combined with mathematical and computational models. In the natural sciences, mathematical and computational models have aided the identification of key mechanisms underlying the behavior of systems comprising multiple interacting components. A number of mathematical and computational models have been proposed to explain the development, growth and death of pancreatic β-cells. In this review, we discuss some of these models and how their predictions provide novel insight into the mechanisms controlling β-cell mass during normal development and diabetes progression. Lastly, we discuss a handful of the major open questions in the field. PMID:25720614

  15. Educator professional development as a component of earthquake and tsunami readiness and early warning systems

    NASA Astrophysics Data System (ADS)

    Pratt-Sitaula, B. A.; Butler, R. F.; Lillie, R. J.; Hunter, N.; Magura, B.; Groom, R.; Hedeen, C.; Johnson, J. A.; Olds, S. E.; Charlevoix, D.; Coe, M.

    2014-12-01

    The implementation of any real-time earthquake analysis for disaster mitigation requires not just scientific expertise and equipment but thoughtful, far-reaching, and long term education for emergency management personnel and the public. The "Cascadia EarthScope Earthquake and Tsunami Education Program" (CEETEP) is working to mitigate these potential disasters through collaboration building and professional development for K-12 teachers, park and museum interpreters, and emergency management outreach educators in communities along the Oregon and Washington coast (2013-2016). In this project nearly 150 coastal Cascadia educators are being introduced to critical knowledge about (among other things) earthquake monitoring and earthquake early warning systems. In collaboration last year with UNAVCO, CEETEP developed an animation explaining how GPS and seismic systems can work in concert to greatly enhance earthquake early warning systems for Cascadia and other subduction zone areas (www.youtube.com/user/unavcovideos, "animations"). Science and preparedness educators are key partners in the endeavor of implementing earthquake and tsunami early warning systems. The knowledge of how to run effective professional development programs for such educators will greatly enhance outreach efforts. Initial results from CEETEP are very encouraging. Four of the planned six workshops were held in 2013 (northern coastal Oregon) and 2014 (Olympic Peninsula, Washington). Results from Year 1 show that participant content knowledge improved from 50% to 86% over the course of the workshop. Similarly, confidence in teaching about workshop topics increased from an average of 2.8 to 5.2 on a 6-point scale. Participant optimism about the efficacy and tractability of community-level planning also increased from 5.7 to 7.4 on a 9-point scale. Nearly 90% of participants continued to be active with the program through the time of the March 8, 2014 Share-a-thon and presented on a wide range of

  16. Changes in the Essential Oil Components during the Development of Fennel Plants from Somatic Embryoids.

    PubMed

    Miura, Y; Ogawa, K; Fukui, H; Tabata, M

    1987-02-01

    Quantitative and qualitative changes of essential oils during the development of clonal plants of fennel propagated through somatic embryogenesis were investigated. Although no essential oil could be detected either in cultured cells or in somatic embryoids, monoter-penes such as alpha-phellandrene and alpha-pinene were found in radical leaves of regenerated plantlets cultured on a hormone-free agar medium. The regenerated plants cultivated in the field for about one month accumulated phenylpropanoids such as estragole, anethole, and fenchone in addition to the two monoterpenes described above in radical leaves. Rich accumulations of phenylpropanoids and monoterpenes were observed in the fruits; especially the contents of estragole and anethole were much higher than in radical leaves.

  17. Advanced manufacturing development of a composite empennage component for l-1011 aircraft

    NASA Technical Reports Server (NTRS)

    1978-01-01

    Tooling concepts were developed which would permit co-couring of the hat stiffeners to the skin to form the cover assembly in a single autoclave cycle. These tooling concepts include the use of solid rubber mandrels, foam mandrels, and formed elastometric bladders. A simplification of the root end design of the cover hat stiffeners was accomplished in order to facilitate fabrication. The conversion of the 3D NASTRAN model from level 15 to level 16 was completed and a successful check run accomplished. A detailed analysis of the thermal load requirement for the environmental chambers was carried out. Based on the thermal analysis, best function requirements, load inputs and ease of access, a system involving four chambers, two for the covers containing 6 and 4 specimens, respectively, and two for the spares containing 6 and 4 specimens, respectively, evolved.

  18. History of the child health and development book. Part 1: 1920 to 1945.

    PubMed

    Clendon, Jill; McBride-Henry, Karen

    2014-03-01

    The New Zealand child health and development record book (also known as the Well Child/Tamariki Ora Health Book or Plunket book) has recorded the history of infant-rearing practices in New Zealand for almost 100 years. Since its initial publication it has been used by mothers and health professionals to track the health and development of children under the age of five years. The book also provides insight on the development of mothering practices and provides commentary on the medicalisation of mothering and the emergence of mothering as a science from the time of its inception. This article, part one of two, explores the history of the Plunket book during the years of 1920 to 1945. Information for this article stems from both primary and secondary sources, including an extensive collection of Plunket books from across New Zealand. The findings chronicle the development of a medicalised relationship between mothers and health professionals. The exploration reveals that the rise of scientific mothering coincided with the devaluing of women-centred mothering knowledge, and as a result the language that described women's mothering experiences was silenced.

  19. History of the child health and development book. Part 2: 1945-2000.

    PubMed

    Clendon, Jill; McBride-Henry, Karen

    2014-07-01

    This is the second part of a historical review of the New Zealand child health and development record book (also known as the Well Child/Tamariki Ora Health book or Plunket book). It focuses on the years between 1945 and 2000. The first article highlighted how the book documented the development of "scientific mothering", which marginalized women-generated mothering knowledge. The present article highlights how during the reviewed time period women began to challenge notions of "scientific mothering", these changes are signaled in the content of the Well Child/Tamariki Ora Health book over time. In addition, women's movements, such as LaLeche league and Parent Centre, reflected significant societal changes during this era in relation to mothering and child-rearing practices, the influence of which had a significant impact on the Plunket book's development. However, tensions between health professionals and women in relation to the value placed on types of knowledge continued to exist as evidenced by the language employed in the Plunket books throughout the time period reviewed. Being mindful of the tensions that exist between competing discourses and knowledge sources is important as they call us to engage with how we value and develop our relationships with women and mothers as health care professionals.

  20. DOE program guide for universities and other research groups. Part I. DOE Research and Development Programs; Part II. DOE Procurement and Assistance Policies/Procedures

    SciTech Connect

    Not Available

    1980-03-01

    This guide addresses the DOE responsibility for fostering advanced research and development of all energy resources, both current and potential. It is intended to provide, in a single publication, all the fundamental information needed by an institution to develop a potential working relationship with DOE. Part I describes DOE research and development programs and facilities, and identifies areas of additional research needs and potential areas for new research opportunities. It also summarizes budget data and identifies the DOE program information contacts for each program. Part II provides researchers and research administrators with an introduction to the DOE administrative policies and procedures for submission and evaluation of proposals and the administration of resulting grants, cooperative agreements, and research contracts. (RWR)